Preliminary design for spent fuel canister handling systems in a canister transfer and installation vehicle

International Nuclear Information System (INIS)

Wendelin, T.; Suikki, M.

2008-12-01

The report presents a spent fuel canister transfer and installation vehicle. The vehicle is used for carrying the fuel canister into a disposal tunnel and installing it into a deposition hole. The report outlines basic requirements and a design for canister handling equipment used in a canister transfer and installation vehicle, a description regarding the operation and maintenance of the equipment, as well as a cost estimate. Specific vehicles will be manufactured for all canister types in order to minimize the height of the disposal tunnels. This report is only focused on a transfer and installation vehicle for OL1-2 fuel canisters. Detailed designing and selection of final components have not yet been carried out. The report also describes the vehicle's requirements for the structures of a repository system, as well as actions in possible malfunction or fault situations. The spent fuel canister is brought from an encapsulation plant by a canister lift down to the repository level. The fuel canister is driven from the canister lift by an automated guided vehicle onto a canister hoist at a canister loading station. The canister transfer and installation vehicle is waiting for the canister with its radiation shield in an upright position above the canister hoist. The hoist carries the canister upward until the vehicle's own lifting means grab hold of the canister and raise it up into the vehicle's radiation shield. This is followed by turning the radiation shield to a transport position and by closing it in a radiation-proof manner against a rear radiation shield. The vehicle is driven along the central tunnel into the disposal tunnel and parked on top of the deposition hole. The vehicle's radiation shield is turned to the upright position and the canister is lowered with the vehicle's hydraulic winches into a bentonite-lined deposition hole. The radiation shield is turned back to the transport position and the vehicle can be driven out of the disposal tunnel

Project Freebird: An orbital transfer vehicle

Science.gov (United States)

Aneses, Carlos A.; Blanchette, Ryan L.; Brann, David M.; Campos, Mario J.; Cohen, Lisa E.; Corcoran, Daniel J., III; Cox, James F.; Curtis, Trevor J.; Douglass, Deborah A.; Downard, Catherine L.

1994-08-01

Freebird is a space-based orbital transfer vehicle designed to repair and deorbit orbital assets. Freebird is based at International Space Station Alpha (ISSA) at an inclination of 51.6 deg and is capable of three types of missions: crewed and teleoperated LEO missions, and extended robotic missions. In a crewed local configuration, the vehicle can visit inclinations between 30.8 deg and 72.4 deg at altitudes close to 390 km. Adding extra fuel tanks extends this range of inclination up to 84.9 deg and down to 18.3 deg. Furthermore, removing the crew module, using the vehicle in a teleoperated manner, and operating with extra fuel tanks allows missions to polar and geosynchronous orbits. To allow for mission flexibility, the vehicle was designed in a semimodular configuration. The major system components include a crew module, a 'smart box' (which contains command, communications, guidance, and navigation equipment), a propulsion pack, extra fuel tanks, and a vehicle storage facility (VSF) for storage purposes. To minimize risk as well as development time and cost, the vehicle was designed using only proven technology or technology which is expected to be flight-qualified in time for the intended launch date of 2002. And, because Freebird carries crew and operates near the space station, it must meet or exceed the NASA reliability standard of 0.994, as well as other standard requirements for such vehicles. The Freebird program was conceived and designed as a way to provide important and currently unavailable satellite repair and replacement services of a value equal to or exceeding operational costs.

Pellet bed reactor for nuclear propelled vehicles: Part 2: Missions and vehicle integration trades

International Nuclear Information System (INIS)

Haloulakos, V.E.

1991-01-01

Mission and vehicle integration tradeoffs involving the use of the pellet bed reactor (PBR) for nuclear powered vehicles is discussed, with much of the information being given in viewgraph form. Information is given on propellant tank geometries, shield weight requirements for conventional tank configurations, effective specific impulse, radiation mapping, radiation dose rate after shutdown, space transfer vehicle design data, a Mars mission summary, sample pellet bed nuclear orbit transfer vehicle mass breakdown, and payload fraction vs. velocity increment

Pellet bed reactor for nuclear propelled vehicles: Part 2: Missions and vehicle integration trades

Science.gov (United States)

Haloulakos, V. E.

1991-01-01

Mission and vehicle integration tradeoffs involving the use of the pellet bed reactor (PBR) for nuclear powered vehicles is discussed, with much of the information being given in viewgraph form. Information is given on propellant tank geometries, shield weight requirements for conventional tank configurations, effective specific impulse, radiation mapping, radiation dose rate after shutdown, space transfer vehicle design data, a Mars mission summary, sample pellet bed nuclear orbit transfer vehicle mass breakdown, and payload fraction vs. velocity increment.

Magnetic Field Emission Comparison for Series-Parallel and Series-Series Wireless Power Transfer to Vehicles – PART 2/2

DEFF Research Database (Denmark)

Batra, Tushar; Schaltz, Erik

2014-01-01

Series-series and series-parallel topologies are the most favored topologies for design of wireless power transfer system for vehicle applications. The series-series topology has the advantage of reflecting only the resistive part on the primary side. On the other hand, the current source output...... characteristics of the series-parallel topology are more suited for the battery of the vehicle. This paper compares the two topologies in terms of magnetic emissions to the surroundings for the same input power, primary current, quality factor and inductors. Theoretical and simulation results show that the series...

Exogenous attention enhances 2nd-order contrast sensitivity

Science.gov (United States)

Barbot, Antoine; Landy, Michael S.; Carrasco, Marisa

2011-01-01

Natural scenes contain a rich variety of contours that the visual system extracts to segregrate the retinal image into perceptually coherent regions. Covert spatial attention helps extract contours by enhancing contrast sensitivity for 1st-order, luminance-defined patterns at attended locations, while reducing sensitivity at unattended locations, relative to neutral attention allocation. However, humans are also sensitive to 2nd-order patterns such as spatial variations of texture, which are predominant in natural scenes and cannot be detected by linear mechanisms. We assess whether and how exogenous attention—the involuntary and transient capture of spatial attention—affects the contrast sensitivity of channels sensitive to 2nd-order, texture-defined patterns. Using 2nd-order, texture-defined stimuli, we demonstrate that exogenous attention increases 2nd-order contrast sensitivity at the attended location, while decreasing it at unattended locations, relative to a neutral condition. By manipulating both 1st- and 2nd-order spatial frequency, we find that the effects of attention depend both on 2nd-order spatial frequency of the stimulus and the observer’s 2nd-order spatial resolution at the target location. At parafoveal locations, attention enhances 2nd-order contrast sensitivity to high, but not to low 2nd-order spatial frequencies; at peripheral locations attention also enhances sensitivity to low 2nd-order spatial frequencies. Control experiments rule out the possibility that these effects might be due to an increase in contrast sensitivity at the 1st-order stage of visual processing. Thus, exogenous attention affects 2nd-order contrast sensitivity at both attended and unattended locations. PMID:21356228

Ariane Transfer Vehicle in service of man in orbit

Science.gov (United States)

Deutscher, N.; Schefold, K.; Cougnet, C.

1988-10-01

The Ariane Transfer Vehicle (ATV), an unmanned propulsion system that is designed to be carried by the Ariane 5 launch vehicle, will undertake the logistical support required by the International Space Station and the Man-Tended Free Flyer, carrying both pressurized and unpressurized cargo to these spacecraft and carrying away wastes. The ATV is an expendable vehicle, disposed of by burn-up during reentry, and will be available for initial operations in 1996. In order to minimize development costs and recurrent costs, the ATV design will incorporate existing hardware and software.

Porous Na2O-B2O3-Nd2O3 material

Energy Technology Data Exchange (ETDEWEB)

De Villiers, D R; Res, M A; Richter, P W

1986-12-01

Substitution of SiO2 by Nd2O3 in the sodium borosilicate system produced glasses containing up to 50 mass% Nd2O3. Sodium borate was leached out of some of the materials to produce either a porous Nd2O3-rich glass or a porous glass-ceramic containing NdBO3, depending on the starting material. Surface areas of up to 190 mS g- were measured. Powder X-ray diffraction (XRD) revealed the NdBO3 to be the high-temperature form with low symmetry.

C-type Nd2Se3

Directory of Open Access Journals (Sweden)

2009-03-01

Full Text Available The title compound, neodymium sesquiselenide, is isotypic with the other known rare-earth metal(III selenides M2Se3 (M = La–Pr and Sm–Lu with the cubic C-type structure. It adopts a cation-defective Th3P4-type arrangement with close to 8/9 of the unique neodymium-cation site occupied, leading to the composition Nd2.667Se4 (Z = 4 or Nd2Se3 (Z = 5.333, respectively. The Nd3+ cations are thus surrounded by eight selenide anions, forming trigonal [NdSe8]13− dodecahedra, whereas the Se2− anions exhibit a sixfold coordination, but due to the under-occupation of neodymium, each one is statistically surrounded by only 5.333 cations. The crystal studied was a merohedral twin with a 0.31 (6:0.69 (6 domain ratio.

Absorption spectra of CsNd(MoO4)2 and CsGd(MoO4)2-Nd3+ crystals in strong magnetic fields

International Nuclear Information System (INIS)

Gorban', I.S.; Kozeeva, L.P.; Slobodyanyuk, A.V.; Shevchenko, V.A.

1987-01-01

The comparison of the electronic structure of Nd 3+ in CsNd(MoO 4 ) 2 and CsGd(MoO 4 ) 2 - Nd 3+ crystals is made. It is established that in these crystals the activator centers, mainly, of the certain type with the symmetry of the local environment C 2 are formed. The absorption spectra of self-activated CsNd(MoO 4 ) 2 crystal differ from spectra of CsGd(MoO 4 ) 2 - Nd 3+ by the presence of the vibrating structure. The Stark splittings of energy levels of Nd 3+ in the investigated crystalline matrices are more sensitive to the environment effect than the Zeeman ones. The ground state of Nd 3+ ion in CsNd(MoO 4 ) 2 and CsGd(MoO 4 ) 2 molybdates is characterized by the similar values of g-factors

Mass spectrometric study of Nd2S3 vaporization

International Nuclear Information System (INIS)

Fenochka, B.V.

1987-01-01

The authors conduct a mass-spectrometric study of neodymium(III) sulfide vaporization. The chemical composition of the samples was stoichiometric and the samples were vaporized from tantalum effusion cells. When the vapor over Nd 2 S 3 is ionized by electrons the mass spectra shows monovalent cations of Nd, S, NdS, and NdO. The enthalpy of vaporization if Nd atoms from Nd 2 S 3 at average experimental temperatures and the standard enthalpy of reaction is shown. Also presented is the enthalpy of vaporization of NdS molecules from Nd 2 S 3 at average experimental temperatures and the standard enthalpy of reaction

Shape transition in the Nd-isotopes

International Nuclear Information System (INIS)

Sandor, Robert Karl Josef.

1991-01-01

In this thesis the results of an electron scattering experiment on 142 Nd, 146 Nd and 150 Nd, designed to study the influence of this shape transition an the low-lying excited states, have been presented and discussed. The spectra have been obtained at the high-resolution electron scattering facility of NIKHEF-K and cover a momentum transfer range from 0.5 up to 2.8 fm -1 . The experimental form factors and transition charge densities have been compared to two microscopic models, i.e. the Quasiparticle-Phonon Model for 142 Nd and 146 Nd and the Density-Dependent Hartree-Fock-Boguliubov model with a dynamical approach to calculate transition charge densities for 146 Nd and 150 Nd. The data obtained for the latter nuclei have also been compared to the macroscopic Rotation-Vibration Model. (author). 127 refs.; 49 figs.; 26 tabs

Fluctuation kinetics of fluorescence hopping quenching in the Nd3+:Y2O3 spherical nanoparticles

International Nuclear Information System (INIS)

Orlovskii, Yu.V.; Popov, A.V.; Platonov, V.V.; Fedorenko, S.G.; Sildos, I.; Osipov, V.V.

2013-01-01

We study the peculiarities of energy transfer kinetics from the 4 F 3/2 laser level in the Nd 3+ doped Y 2 O 3 spherical nanoparticles of monoclinic phase synthesized by laser ablation of solid targets with subsequent recondensation in flow of air at atmospheric pressure comparing to the similar bulk crystal. We show that the fluorescence quenching in the nanoparticles is determined by two processes depending on Nd 3+ concentration and the degree of dehydration. At concentrations less than 1% the fluorescence quenching is mainly determined by direct (static) quenching by vibrations of OH − molecular groups associated with oxygen vacancies. At concentrations greater than 1 at % quenching is due to energy migration over neodymium ions, followed by the Nd 3+ –OH − quenching. In the latter case, the first time in a solid-state impurity laser medium we observe non-stationary kinetics on the entire length of a time-dependent luminescence quenching, starting from static decay and ending with fluctuation kinetics of fluorescence hopping quenching. -- Highlights: ► We prepare monoclinic Nd 3+ :Y 2 O 3 spherical NPs of mean D=12 nm by laser ablation of solid targets. ► We detect the fluorescence quenching of Nd 3+ the 4 F 3/2 level by vibrations of OH – molecular groups. ► We find that at 0.1% of Nd 3+ the process of static quenching by vibrations of OH – dominates. ► We find that Nd 3+ –Nd 3+ energy migration accelerates the Nd 3+ –OH − quenching at 1% of Nd 3+ . ► We detect non-stationary quenching kinetics ending with fluctuation stage of hopping quenching

High Precision 142Nd/144Nd and 143Nd/144Nd Isotope Ratio Measurements in Rock Samples

Science.gov (United States)

Ali, A.; Srinivasan, G.

2009-05-01

The long-lived 147Sm-143Nd system with a half-life (T1/2) of 106 Gyr is generally used for geochronology. The short-lived 146Sm-142Nd system (T1/2= 103 Myr) is used as a geological tracer to track early (˜500 Ma) silicate differentiation [1] events in different planetary bodies. The isotope composition measurements by thermal ionization mass spectrometry (TIMS) require purification of Nd using chemical separation methods. This is important as an impure sample will give both a very poor ion yield and cause beam instability in the mass spectrometer, potentially resulting in a poor analysis [2]. The separation of Nd for 143Nd isotope measurement is, fairly straightforward because there is no isobaric interference of any other REE. While 142Nd isotope analysis needs chemically separated Nd fraction to be ˜100% Ce-free as latter is composed of a substantial amount of 142Ce isotope. A 4-steps technique, modified from Caro et al., [3], for the separation of Nd is established at the Cosmochemistry Laboratory of University of Toronto, Canada and applied to the measurement of Nd isotope ratios in geological reference sample BCR-2 (USGS, Columbia River basalt) using TIMS. Results of the isotopic ratios obtained for BCR-2 are in good agreement with published values [e.g., 4]. Analytical work on the samples discovered as the oldest rocks on Earth [5] from Nuvvuagittuq greenstone belt in Québec, Canada and various meteorites is in progress. An account of the procedures involved is briefly described here. All working solutions and acids were prepared using >18.2 MΩ.cm-1 H2O from a Milli-Q water system. Experiments were performed under Class 100 clean work bench with acid-cleaned apparatus and plastic-ware. The whole rock powders were weighed (20-30 mg) and dissolved in a mixture of HF and HNO3 using PFA vials and heated at 110°C. Further decomposition was done in Teflon bomb in the oven at 205°C. Later on contents of the Teflon bomb were transferred to vials and fluorides

Research on the transfer learning of the vehicle logo recognition

Science.gov (United States)

Zhao, Wei

2017-08-01

The Convolutional Neural Network of Deep Learning has been a huge success in the field of image intelligent transportation system can effectively solve the traffic safety, congestion, vehicle management and other problems of traffic in the city. Vehicle identification is a vital part of intelligent transportation, and the effective information in vehicles is of great significance to vehicle identification. With the traffic system on the vehicle identification technology requirements are getting higher and higher, the vehicle as an important type of vehicle information, because it should not be removed, difficult to change and other features for vehicle identification provides an important method. The current vehicle identification recognition (VLR) is mostly used to extract the characteristics of the method of classification, which for complex classification of its generalization ability to be some constraints, if the use of depth learning technology, you need a lot of training samples. In this paper, the method of convolution neural network based on transfer learning can solve this problem effectively, and it has important practical application value in the task of vehicle mark recognition.

Project 2nd Periodic Report - Section 2

DEFF Research Database (Denmark)

Healy, Mark; Knowles, Emma; Johnstone, Cameron

The work described in this publication has received support from the European Community - Research Infrastructure Action under the FP7 “Capacities” Specific Programme through grant agreement number 262552, MaRINET. Project Periodic Report. 2nd Period: October 2012 – March 2014 inclusive.......The work described in this publication has received support from the European Community - Research Infrastructure Action under the FP7 “Capacities” Specific Programme through grant agreement number 262552, MaRINET. Project Periodic Report. 2nd Period: October 2012 – March 2014 inclusive....

Emission sensitization processes involving Nd{sup 3+} in YAG

Energy Technology Data Exchange (ETDEWEB)

Lupei, V., E-mail: lupei_voicu@yahoo.com [National Institute of Laser, Plasma and Radiation Physics, Bucharest 077125 (Romania); Lupei, A.; Gheorghe, C. [National Institute of Laser, Plasma and Radiation Physics, Bucharest 077125 (Romania); Ikesue, A. [World Lab. Co., Nagoya (Japan)

2016-02-15

The paper investigates the characteristics of sensitization processes of Nd{sup 3+} emission in YAG ceramics under broad band pumping by co-doping with Cr{sup 3+} and the prospect of using Nd{sup 3+} and Cr{sup 3+} for sensitization of emission of Yb{sup 3+}. It is evidenced that the energy transfer from Cr{sup 3+} to Nd{sup 3+} involves both direct and weak migration-assisted processes and is thus dependent on the concentrations of both species. It is also found that the ion–ion interaction responsible for the direct transfer contains besides the dipole–dipole coupling strong superexchange contribution that dominates the transfer to the Nd{sup 3+} ions up to the third coordination sphere and has major implication in sensitization. Investigation of (Cr, Nd, Yb)-doped YAG ceramics shows that Cr{sup 3+} can sensitize the emission of Yb{sup 3+} both via the chain Cr–Nd–Yb or by direct Cr–Yb energy transfer. The prospect of utilization of these processes in the solar-pumped laser is discussed. - Highlights: • The efficiency of sensitization increases at high Cr and Nd doping concentrations. • The Cr-to-Nd energy transfer involves both direct and migration-assisted processes. • The direct transfer implies both dipole–dipole and superexchange interactions. • The superexchange interaction has major influence on sensitization. • Sensitized emission of Yb{sup 3+} in (Cr,Nd,Yb):YAG by Cr–Nd–Yb and Cr–Yb transfers.

Simulations of heat transfer through the cabin walls of rail vehicle

Directory of Open Access Journals (Sweden)

Schuster M.

2007-10-01

Full Text Available This paper deals with industrial application of numerical methods to the prediction of thermal situation in the rail vehicle interior. Basic principles of heat transfer are summarised to explain both theoretical background of simulations and engineering approach to solving temperature conditions in the vehicle interior. The main part of the contribution describes the solution of the locomotive driver’s cabin heating and controlling the temperature levels. This contribution is a brief overview of both possibilities of engineering modelling of heat transfer modes and results in the simulation of the real locomotive cabin heating/ventilation system design.

Singlet Energy Transfer as the Main Pathway in the Sensitization of Near-Infrared Nd3+ Luminescence by Dansyl and Lissamine Dyes

NARCIS (Netherlands)

Hebbink, G.A.; Klink, S.I.; Grave, Lennart; Oude Alink, Patrick G.B.; van Veggel, F.C.J.M.

2002-01-01

general, sensitization of lanthanide(III) ions by organic sensitizers is regarded to take place via the triplet state of the sensitizers. Herein, we show that in dansyl- and lissamine-functionalized Nd3+ complexes energy transfer occurs from the singlet state of the sensitizers to the Nd3+ center.

Antiferromagnetic Nd ordering in NdPd{sub 2}Ga{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Doenni, A.; Fischer, P.; Fauth, F.; Zolliker, M. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Bauer, E. [Technische Univ., Vienna (Austria)

1997-09-01

The ternary intermetallic compound NdPd{sub 2}Ga{sub 3} was investigated by powder neutron diffraction: the crystal structure agrees well with the ordered hexagonal PrNi{sub 2}Al{sub 3}-type structure. The antiferromagnetic ordering below T{sub N} 6.5 K corresponds to a propagation vector k = [1/2,0,0]. The ordered magnetic Nd moments of (1.99 {+-} 0.04) {mu}{sub B} at saturation lie in the basal plane due to the crystal-electric field anisotropy and are oriented perpendicular to the propagation vector. (author) 1 fig., 1 tab., 2 refs.

Electronic structure of layered titanate Nd 2Ti 2O 7

Science.gov (United States)

Atuchin, V. V.; Gavrilova, T. A.; Grivel, J.-C.; Kesler, V. G.

2008-10-01

The electronic structure of the binary titanate Nd 2Ti 2O 7 has been studied by X-ray photoelectron spectroscopy (XPS). Spectral features of the valence band and all constituent element core levels have been considered. The Auger parameters of titanium and oxygen in Nd 2Ti 2O 7 are determined as αTi = 873.5 and αO = 1042.2 eV. Chemical bonding effects have been discussed with the binding energies differences ΔTi = (BE O 1s - BE Ti 2p 3/2) = 71.5 eV and ΔNd = (BE Nd 3d 5/2 - BE O 1s) = 452.5 eV as key parameters in comparison with those in other titanium- and neodymium-bearing oxides.

Benefits of high aerodynamic efficiency to orbital transfer vehicles

Science.gov (United States)

Andrews, D. G.; Norris, R. B.; Paris, S. W.

1984-01-01

The benefits and costs of high aerodynamic efficiency on aeroassisted orbital transfer vehicles (AOTV) are analyzed. Results show that a high lift to drag (L/D) AOTV can achieve significant velocity savings relative to low L/D aerobraked OTV's when traveling round trip between low Earth orbits (LEO) and alternate orbits as high as geosynchronous Earth orbit (GEO). Trajectory analysis is used to show the impact of thermal protection system technology and the importance of lift loading coefficient on vehicle performance. The possible improvements in AOTV subsystem technologies are assessed and their impact on vehicle inert weight and performance noted. Finally, the performance of high L/D AOTV concepts is compared with the performances of low L/D aeroassisted and all propulsive OTV concepts to assess the benefits of aerodynamic efficiency on this class of vehicle.

Mixed alkali neodymium orthoborates: K_9Li_3Nd_3(BO_3)_7 and A_2LiNd(BO_3)_2 (A = Rb, Cs)

International Nuclear Information System (INIS)

Chen, Pengyun; Xia, Mingjun; Li, Rukang

2016-01-01

Crystals of mixed alkali neodymium orthoborates, K_9Li_3Nd_3(BO_3)_7 and A_2LiNd(BO_3)_2 (A = Rb, Cs) were obtained by spontaneous crystallization. K_9Li_3Nd_3(BO_3)_7 crystallizes in space group P2/c with cell parameters of a = 11.4524(7) Aa, b = 10.1266(6) Aa, c = 12.3116 (10) Aa, β = 122.0090(10) . In the structure, NdO_8 polyhedra share corners and connect with planer BO_3 groups to form infinite [Nd_3B_3O_2_1]_n chains. These chains are linked by additional BO_3 groups to produce a double layer of [Nd_6B_6O_3_8]_n blocks in the ac plane with K and Li ions filled into the cavities. A_2LiNd(BO_3)_2 (A = Rb, Cs) crystallizes in space group Pbcm, with cell parameters of a = 7.113(2) Aa, b = 9.691(3) Aa and c = 10.135(3) Aa for Rb_2LiNd(BO_3)_2, and a = 7.2113(3) Aa, b = 9.9621(4) Aa, and c = 10.3347(4) Aa for Cs_2LiNd(BO_3)_2. In the structure, NdO_8 polyhedra are corner-sharing with each other and further interlinked by BO_3 groups to comprise the infinite [Nd_4B_4O_2_4] sheets in the bc plane, with Rb/Cs and Li ions occupying the interlayered space. The compounds show effective near-IR emission and their associated lifetimes are obtained by fluorescence spectra. (Copyright copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Crystal-field energy level analysis for Nd3+ ions at the low symmetry C1 site in [Nd(hfa)4(H2O)](N(C2H5)4) single crystals

International Nuclear Information System (INIS)

Mech, Agnieszka; Gajek, Zbigniew; Karbowiak, Miroslaw; Rudowicz, Czeslaw

2008-01-01

Optical absorption measurements of Nd 3+ ions in single crystals of [Nd(hfa) 4 (H 2 O)](N(C 2 H 5 ) 4 ) (hfa = hexafluoroacetyloacetonate), denoted Nd(hfa) for short, have been carried out at 4.2 and 298 K. This compound crystallizes in the monoclinic system (space group P 2 1 /n). Each Nd ion is coordinated to eight oxygen atoms that originate from the hexafluoroacetylacetonate ligands and one oxygen atom from the water molecule. A total of 85 experimental crystal-field (CF) energy levels arising from the Nd 3+ (4f 3 ) electronic configuration were identified in the optical spectra and assigned. A three-step CF analysis was carried out in terms of a parametric Hamiltonian for the actual C 1 symmetry at the Nd 3+ ion sites. In the first step, a total of 27 CF parameters (CFPs) in the Wybourne notation B kq , admissible by group theory, were determined in a preliminary fitting constrained by the angular overlap model predictions. The resulting CFP set was reduced to 24 specific independent CFPs using appropriate standardization transformations. Optimizations of the second-rank CFPs and extended scanning of the parameter space were employed in the second step to improve reliability of the CFP sets, which is rather a difficult task in the case of no site symmetry. Finally, seven free-ion parameters and 24 CFPs were freely varied, yielding an rms deviation between the calculated energy levels and the 85 observed ones of 11.1 cm -1 . Our approach also allows prediction of the energy levels of Nd 3+ ions that are hidden in the spectral range overlapping with strong ligand absorption, which is essential for understanding the inter-ionic energy transfer. The orientation of the axis system associated with the fitted CF parameters w.r.t. the crystallographic axes is established. The procedure adopted in our calculations may be considered as a general framework for analysis of CF levels of lanthanide ions at low (triclinic) symmetry sites

Crystal-field energy level analysis for Nd(3+) ions at the low symmetry C(1) site in [Nd(hfa)(4)(H(2)O)](N(C(2)H(5))(4)) single crystals.

Science.gov (United States)

Mech, Agnieszka; Gajek, Zbigniew; Karbowiak, Mirosław; Rudowicz, Czesław

2008-09-24

Optical absorption measurements of Nd(3+) ions in single crystals of [Nd(hfa)(4)(H(2)O)](N(C(2)H(5))(4)) (hfa = hexafluoroacetyloacetonate), denoted Nd(hfa) for short, have been carried out at 4.2 and 298 K. This compound crystallizes in the monoclinic system (space group P 2(1)/n). Each Nd ion is coordinated to eight oxygen atoms that originate from the hexafluoroacetylacetonate ligands and one oxygen atom from the water molecule. A total of 85 experimental crystal-field (CF) energy levels arising from the Nd(3+) (4f(3)) electronic configuration were identified in the optical spectra and assigned. A three-step CF analysis was carried out in terms of a parametric Hamiltonian for the actual C(1) symmetry at the Nd(3+) ion sites. In the first step, a total of 27 CF parameters (CFPs) in the Wybourne notation B(kq), admissible by group theory, were determined in a preliminary fitting constrained by the angular overlap model predictions. The resulting CFP set was reduced to 24 specific independent CFPs using appropriate standardization transformations. Optimizations of the second-rank CFPs and extended scanning of the parameter space were employed in the second step to improve reliability of the CFP sets, which is rather a difficult task in the case of no site symmetry. Finally, seven free-ion parameters and 24 CFPs were freely varied, yielding an rms deviation between the calculated energy levels and the 85 observed ones of 11.1 cm(-1). Our approach also allows prediction of the energy levels of Nd(3+) ions that are hidden in the spectral range overlapping with strong ligand absorption, which is essential for understanding the inter-ionic energy transfer. The orientation of the axis system associated with the fitted CF parameters w.r.t. the crystallographic axes is established. The procedure adopted in our calculations may be considered as a general framework for analysis of CF levels of lanthanide ions at low (triclinic) symmetry sites.

The expression characteristics of mt-ND2 gene in chicken.

Science.gov (United States)

Zhang, Wenwen; Hou, Lingling; Wang, Ting; Lu, Weiwei; Tao, Yafei; Chen, Wen; Du, Xiaohui; Huang, Yanqun

2016-09-01

Subunit 2 of NADH dehydrogenase (ND2) is encoded by the mt-ND2 gene and plays a critical role in controlling the production of the mitochondrial reactive oxygen species. Our study focused on exploring the mt-ND2 tissue expression patterns and the effects of energy restriction and dietary fat (linseed oil, corn oil, sesame oil or lard) level (2.5% and 5%) on its expression in chicken. The results showed that mt-ND2 gene was expressed in the 15 tissues of hybrid chickens with the highest level in heart and lowest level in pancreas tissue; 30% energy restriction did not significantly affect mt-ND2 mRNA level in chicken liver tissue. Both the mt-ND2 mRNA levels in chicken pectoralis (p chicken age (p chicken age (p chicken age.

Crystal-field energy level analysis for Nd3+ ions at the low symmetry C1 site in [Nd(hfa)4(H2O)](N(C2H5)4) single crystals

Science.gov (United States)

Mech, Agnieszka; Gajek, Zbigniew; Karbowiak, Mirosław; Rudowicz, Czesław

2008-09-01

Optical absorption measurements of Nd3+ ions in single crystals of [Nd(hfa)4(H2O)](N(C2H5)4) (hfa = hexafluoroacetyloacetonate), denoted Nd(hfa) for short, have been carried out at 4.2 and 298 K. This compound crystallizes in the monoclinic system (space group P 21/n). Each Nd ion is coordinated to eight oxygen atoms that originate from the hexafluoroacetylacetonate ligands and one oxygen atom from the water molecule. A total of 85 experimental crystal-field (CF) energy levels arising from the Nd3+ (4f3) electronic configuration were identified in the optical spectra and assigned. A three-step CF analysis was carried out in terms of a parametric Hamiltonian for the actual C1 symmetry at the Nd3+ ion sites. In the first step, a total of 27 CF parameters (CFPs) in the Wybourne notation Bkq, admissible by group theory, were determined in a preliminary fitting constrained by the angular overlap model predictions. The resulting CFP set was reduced to 24 specific independent CFPs using appropriate standardization transformations. Optimizations of the second-rank CFPs and extended scanning of the parameter space were employed in the second step to improve reliability of the CFP sets, which is rather a difficult task in the case of no site symmetry. Finally, seven free-ion parameters and 24 CFPs were freely varied, yielding an rms deviation between the calculated energy levels and the 85 observed ones of 11.1 cm-1. Our approach also allows prediction of the energy levels of Nd3+ ions that are hidden in the spectral range overlapping with strong ligand absorption, which is essential for understanding the inter-ionic energy transfer. The orientation of the axis system associated with the fitted CF parameters w.r.t. the crystallographic axes is established. The procedure adopted in our calculations may be considered as a general framework for analysis of CF levels of lanthanide ions at low (triclinic) symmetry sites.

Influence of microstructural change of the interface between Nd2Fe14B and Nd-O phases on coercivity of Nd-Fe-B films by oxidation and subsequent low-temperature annealing

International Nuclear Information System (INIS)

Matsuura, Masashi; Tezuka, Nobuki; Sugimoto, Satoshi; Goto, Ryota

2011-01-01

This study provides the influence of microstructural change of the interface between Nd 2 Fe 14 B and Nd-O phases on coercivity of Nd-Fe-B thin films during annealing at low temperature (∼350 deg. C). All films were prepared by using ultra high vacuum (UHV) magnetron sputtering, and the Nd-Fe-B layer was oxidized under Ar gas atmosphere (O 2 content; ∼2 Vol.ppm). Then, the films were annealed at 250-350 deg. C under UHV condition. After oxidation, the coercivity of Nd-Fe-B film decreased to around 40% of the coercivity of as-deposited Nd-Fe-B film. The Nd-rich phase changed from α-Nd to amorphous Nd(-O), and the interface of Nd 2 Fe 14 B/Nd(-O) became rough. In the Nd-Fe-B films oxidized and subsequent annealed at 350 deg. C, the coercivity decreased to around 20%. In the films, poly crystalline hcp Nd 2 O 3 phase crystallized in Nd-rich phase, and there were some steps at the surface of Nd 2 Fe 14 B phase contacting with hcp Nd 2 O 3 phase. Regardless of crystal orientation of Nd 2 Fe 14 B, the microstructural changes of the interface described above were observed.

Future orbital transfer vehicle technology study. Volume 1: Executive summary

Science.gov (United States)

Davis, E. E.

1982-01-01

Reusable space and ground based LO2/LH2 OTV's, both advanced space engines and aero assist capability were compared. The SB OTV provided advantages in life cycle cost, performance and potential for improvement. An all LO2/LH2 OTV fleet was also compared with a fleet of LO2/.H2 OTV's and electric OTV's. The normal growth technology electric OTV used silicon cells with heavy shielding and argon ion thrusters. In this case, the LO2/LH2 OTV fleet provided a 23% advantage in total transportation cost. An accelerated technology LF2/LH2 OTV provided improvements in performance relative to LO2/.H2 OTV but has higher DDT&E cost which negated its cost effectiveness. The accelerated technology electric vehicle used GaAs cells and annealing but still did not result in the mixed fleet being any cheaper than an all LO2/LH2 OTV fleet. It is concluded that reusable LO2/LH2 OTV's can serve all general purpose cargo roles between LEO and GEO for the forseeable future. The most significant technology for the second generation vehicle would be space debris protection, on orbit propellant storage and transfer and on orbit maintenance capability.

40 CFR 80.532 - How are motor vehicle diesel fuel credits used and transferred?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false How are motor vehicle diesel fuel... AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel....532 How are motor vehicle diesel fuel credits used and transferred? (a) Credit use stipulations. Motor...

Housing of Cull Sows in the Hours before Transport to the Abattoir—An Initial Description of Sow Behaviour While Waiting in a Transfer Vehicle

DEFF Research Database (Denmark)

Herskin, Mette S.; Fogsgaard, Katrine Kop; Erichsen, Ditte

2017-01-01

of the sows, after which they (in groups of 7–13) were mixed and moved to the transfer vehicle (median stocking density: 1.2 sow/m2), and driven a short distance to a public road. The duration of the stays in the transfer vehicles before being loaded onto the commercial trucks ranged from 6–59 min. During......In modern pig production, sows are transported by road to abattoirs. For reasons of biosecurity, commercial trucks may have limited access to farms. According to Danish regulations, sows can be kept in stationary transfer vehicles away from the farm for up to two hours before being loaded onto...

The Ariane Transfer Vehicle (ATV) system studies

Science.gov (United States)

Thomas, U.; Thirkettle, A.

1991-08-01

Two distinct concepts of the Ariane transfer vehicle (ATV) are compared which incorporate existing ATV technology and offer logistics delivery at competitive costs. One concept is based on the Ariane-5 upper stage and the Vehicle Equipment Bay, and the other does not include Ariane-5 functions so that existing upper-stage limitations can be eliminated. Both concepts are required to accomplish the same transport, rendezvous, and berthing maneuvers and allow for controlled destructive reentry. An ATV reference mission is outlined, and key ATV design drivers are listed which include safety requirements, debris protection, and propulsion criteria. The Ariane-5 upgrade is the most cost-effective design although the second design is more operationally efficient. The ATV can potentially be used to relieve the schedule of the shuttle flights required for building the Space Station Freedom.

The History of the 2nd Ranger Company

National Research Council Canada - National Science Library

Bond, Victor

2003-01-01

The purpose of this research project is to uncover the history of the 2nd Ranger Company and to determine the impact segregation had on the selection, training, and combat operations of the 2nd Ranger Company...

Energy transfer mechanism between manganese and neodymium

Energy Technology Data Exchange (ETDEWEB)

Kumar, R [Department of Physics, Government Raza Post-Graduate College, Rampur 244901, U.P., India

1977-01-01

The mechanism of energy transfer between Mn/sup 2 +/ ..-->.. Nd/sup 3 +/ in barium borate glass has been investigated. The change in emission intensities and lifetimes of Mn/sup 2 +/ (donor) due to the presence of Nd/sup 3 +/ (acceptor) are observed. It has been concluded that the mechanism of energy transfer involves a nonradiative resonance process. The electrostatic multiple interaction responsible for the transfer is dipole-dipole in nature.

LINK2009 Phase 1: Development of 2. generation fuel cell vehicles and hydrogen refueling station. Final report; LINK2009 fase 1: Udvikling af 2. gen. braendselscelle koeretoejer og brinttankstation. Slutrapport

Energy Technology Data Exchange (ETDEWEB)

2010-03-15

LINK2009 project was to develop 2nd gen. technologies fuel cell systems for vehicles and 350bar hydrogen refueling stations. Also the LINK2009 project were to ensure a continuously positioning of Denmark and the Scandinavian Region within hydrogen for transport and continue to attract international car manufacturers to conduct demonstration and later market introduction in the region. The LINK2009 project is divided in two phases where this first phase only deals with the development of the 2nd generation technologies, whereas the following phase 2 will include the demonstration hereof as well as additional research activities. This Report describes the results of the phase 1 that was commenced in summer 2008 and ended in late 2009. Phase 1 has resulted in the development of new 2nd generation fuel cell technology for use in a city car and a service vehicle. Stated targets for price and efficiency have been reached and the following demonstration in Phase 2 is to confirm reaching of life time targets. The efficiency of the fuel cell system for the city car has been measured to be 42-48% at a power delivery of respectively 10kW and 2kW, which is significantly above the target of >40%. System simplifications and selection of new components have enabled a 50% reduction in the kW price for the fuel cell system, including 700bar hydrogen storage, now totalling Euro 4.500/kW. This creates sufficient basis for conducting demonstration of the system in vehicles. 9 vehicles are planned to be demonstrated in the following phase 2. Additional 8 vehicles were put in operation in Copenhagen in November 2009. Phase 1 has conducted development of 2nd gen. hydrogen refuelling technology that has resulted in concepts for both 350bar and 700bar refuelling as well as a concept for onsite hydrogen production at refuelling stations. In separate projects the developed 350bar technology has been brought to use in a newly established hydrogen station in Copenhagen, and the hydrogen

Ansaldo programs on fuel cell vehicles

Energy Technology Data Exchange (ETDEWEB)

Marcenaro, B.G.; Federici, F. [Ansaldo Ricerche Srl, Genova (Italy)

1996-12-31

The growth in traffic and the importance of maintaining a stable ecology at the global scale, particularly with regard to atmospheric pollution, raises the necessity to realize a new generation of vehicles which are more efficient, more economical and compatible with the environment. At European level, the Car of Tomorrow task force has identified fuel cells as a promising alternative propulsion system. Ansaldo Ricerche has been involved in the development of fuel cell vehicles since the early nineties. Current ongoing programs relates to: (1) Fuel cell bus demonstrator (EQHEPP BUS) Test in 1996 (2) Fuel cell boat demonstrator (EQHHPP BOAT) Test in 1997 (3) Fuel cell passenger car prototype (FEVER) Test in 1997 (4) 2nd generation Fuel cell bus (FCBUS) 1996-1999 (5) 2nd generation Fuel cell passenger car (HYDRO-GEN) 1996-1999.

Electronic structure of layered titanate Nd2Ti2O7

DEFF Research Database (Denmark)

Atuchin, V.V.; Gavrilova, T.A.; Grivel, Jean-Claude

2008-01-01

The electronic structure of the binary titanate Nd2Ti2O7 has been studied by X-ray photoelectron spectroscopy (XPS). Spectral features of the valence band and all constituent element core levels have been considered. The Auger parameters of titanium and oxygen in Nd2Ti2O7 are determined as alpha...

NIR emission and Ce{sup 3+}–Nd{sup 3+} energy transfer in LaCaAl{sub 3}O{sub 7} phosphor prepared by combustion synthesis

Energy Technology Data Exchange (ETDEWEB)

Pathak, A.A. [National Power Training Institute, South Ambazari Road, Nagpur 440022 (India); Talewar, R.A., E-mail: talewarrupesh@gmail.com [Physics Department, Shri Ramdeobaba College of Engineering and Management, Katol Road, Nagpur 440013 (India); Joshi, C.P. [Physics Department, Shri Ramdeobaba College of Engineering and Management, Katol Road, Nagpur 440013 (India); Moharil, S.V. [Department of Physics, Rashtrasant Tukadoji Maharaj Nagpur University, Nagpur 440010 (India)

2016-11-15

Near infrared (NIR) emitting phosphor, LaCaAl{sub 3}O{sub 7}:Ce{sup 3+},Nd{sup 3+} was synthesized by one step combustion synthesis and characterized with scanning electron microscope, photoluminescence emission, photoluminescence excitation spectra and fluorescence decay measurements. When excited with UV, the phosphor gives broadband emission at 410 nm, which corresponds to the allowed 5d→4f transition of Ce{sup 3+} ions and an intense NIR emissions in the range 800–1400 nm, which are assigned to the characteristic transitions from {sup 4}I{sub 9/2,11/2,13/2} states of Nd{sup 3+} ions. The dependences of visible and NIR emissions, decay lifetime and the energy transfer efficiency (η{sub ETE}) on dopant concentrations were investigated in detail. The luminescence spectra, both in visible (VIS) and NIR regions, and decay curves of Ce{sup 3+} have been measured to prove energy transfer (ET) from Ce{sup 3+} to Nd{sup 3+}. These results demonstrate the possibility for enhancing the photovoltaic conversion efficiency of c-Si solar cell by modifying the absorption and utilizing the UV part of the solar spectrum where the efficiency of c-Si solar cell is low.

A matheuristic for transfer synchronization through integrated timetabling and vehicle scheduling

DEFF Research Database (Denmark)

Fonseca, João Paiva; van der Hurk, Evelien; Roberti, Roberto

2018-01-01

Long transfer times often add unnecessary inconvenience to journeys in public transport systems. Synchronizing relevant arrival and departure times through small timetable modifications could reduce excess transfer times, but may also directly affect the operational costs, as the timetable defines...... the set of feasible vehicle schedules. Therefore better results in terms of passenger service, operational costs, or both, could be obtained by solving these problems simultaneously....

Fire simulation of the canister transfer and installation vehicle

International Nuclear Information System (INIS)

Peltokorpi, L.

2012-12-01

A pyrolysis model of the canister transfer and installation vehicle was developed and vehicle fires in the final disposal tunnel and in the central tunnel were simulated using the fire simulation program FDS (Fire Dynamics Simulator). For comparison, same vehicle fire was also simulated at conditions in which the fire remained as a fuel controlled during the whole simulation. The purpose of the fire simulations was to simulate the fire behaviour realistically taking into account for example the limitations coming from the lack of oxygen. The material parameters for the rubber were defined and the simulation models for the tyres developed by simulating the fire test of a front wheel loader rubber tyre done by SP Technical Research Institute of Sweden. In these simulations the most important phenomena were successfully brought out but the timing of the phenomena was difficult. The final values for the rubber material parameters were chosen so that the simulated fire behaviour was at least as intense as the measured one. In the vehicle fire simulations a hydraulic oil or diesel leak causing a pool fire size of 2 MW and 2 m 2 was assumed. The pool fire was assumed to be located under the tyres of the SPMT (Self Propelled Modular Transporters) transporter. In each of the vehicle fire simulations only the tyres of the SPMT transporter were observed to be burning whereas the tyres of the trailer remained untouched. In the fuel controlled fire the maximum power was slightly under 10 MW which was reached in about 18 minutes. In the final disposal tunnel the growth of the fire was limited due to the lack of oxygen and the relatively fast air flows existing in the tunnel. Fast air flows caused the flame spreading to be limited to the certain directions. In the final disposal tunnel fire the maximum power was slightly over 7 MW which was reached about 8 minutes after the ignition. In the central tunnel there was no shortage of oxygen but the spread of the fire was limited due

Effect of mixing RE elements (Nd, Sm, Gd, Eu, Y, Yb) on the RE2BaCuO5/Nd4-2xBa2+2xCu2-xO10-2x phases in RE cuprate high-Tc superconductors

International Nuclear Information System (INIS)

Langhorn, J.B.; Black, M.A.; McGinn, P.J.

1999-01-01

The phases RE 2 BaCuO 5 /RE 4 Ba 2 Cu 2 O 10 phases (where RE is a mixture of Nd, Sm, Gd, Eu, Y and Yb) have been synthesized in an oxygen atmosphere and subsequently characterized. The mixing of RE elements which inherently form the RE 2 BaCuO 5 phase through the peritectic decomposition of REBa 2 Cu 3 O 7-x (RE123) (i.e. Sm, Gd, Eu, Y, Yb), was observed to give homogeneous mixing of the elements in the 211 phase. In contrast it was found that on mixing Nd with other RE elements a mixture of the Nd 4-2x Ba 2+2x Cu 2-x O 10-2x (Nd422) and RE 2 BaCuO 5 (RE211) phases resulted. It was also observed that on mixing Nd with other REs a finite amount of the RE is substituted into the Nd422 phase and Nd into the RE211. (author)

Orbital transfer vehicle concept definition and system analysis study, 1985. Volume 2: OTV concept definition and evaluation. Book 4: Operations

Science.gov (United States)

Mitchell, Jack C.; Keeley, J. T.

1985-01-01

The benefits of the reusable Space Shuttle and the advent of the new Space Station hold promise for increasingly effective utilization of space by the scientific and commercial as well as military communities. A high energy reusable oribital transfer vehicle (OTV) represents an additional capability which also exhibits potential for enhancing space access by allowing more ambitious missions and at the same time reducing launch costs when compared to existing upper stages. This section, Vol. 2: Book 4, covers launch operations and flight operations. The launch operations section covers analyses of ground based and space based vehicles, launch site facilities, logistics requirements, propellant loading, space based maintenance and aft cargo carrier access options. The flight operations sections contain summary descriptions of ground based and space based OTV missions, operations and support requirements, and a discussion of fleet implications.

Spectroscopic properties of Er/Nd co-doped yttrium lanthanum oxide transparent ceramics pumped at 980 nm

Energy Technology Data Exchange (ETDEWEB)

Shao, Yingjie; Yang, Qiuhong, E-mail: yangqiuhong@shu.edu.cn; Gui, Yan; Yuan, Ye; Lu, Qing

2016-05-15

(Er{sub 0.01}Nd{sub x}Y{sub 0.89-x}La{sub 0.1}){sub 2}O{sub 3} (x = 0, 0.001, 0.002, 0.005, 0.01) transparent ceramics were prepared by conventional ceramic processing. The Nd{sup 3+} content dependencies of mid-infrared, near infrared and up-conversion emission of Er{sup 3+} pumped at 980 nm were fully presented. Mechanism of energy transfer between Er{sup 3+} and Nd{sup 3+} was also demonstrated. The results showed that co-doping 0.1 at% Nd{sup 3+} into 1 at% Er{sup 3+} doped yttrium lanthanum oxide transparent ceramic enhanced the 2.7 μm emission significantly and meanwhile suppressed the 1.5 μm emission effectively which indicated an improvement in population inversion between Er:{sup 4}I{sub 11/2} and Er:{sup 4}I{sub 13/2}. Moreover, green up-conversion emission of Er{sup 3+} ion also showed a great improvement by co-doping 0.1 at% Nd{sup 3+}. Those great results were attributed to energy recycle from Er:{sup 4}I{sub 13/2} to Er:{sup 4}I{sub 11/2}. The energy recycle was mainly built by the two energy transfer between Er{sup 3+} and Nd{sup 3+} (one is from Er to Nd, another is in opposite way). So, Er/Nd co-doped yttrium lanthanum oxide transparent ceramic with Nd in low concentration can be considered as a promising laser material for ∼3 μm and up-conversion laser application. - Highlights: • (Er{sub 0.01}Nd{sub x}Y{sub 0.89-x}La{sub 0.1}){sub 2}O{sub 3} transparent ceramics were prepared. • The emission of 2.7 μm of Er{sup 3+} ion was significantly enhanced as x was 0.001. • The emission of 1.5 μm of Er{sup 3+} ion was suppressed greatly by co-doping Nd{sup 3+} ion. • Mechanism of Er–Nd energy transfer was discussed by the energy sketch.

Wireless power transfer for electric vehicles and mobile devices

CERN Document Server

Rim, Chun T

2017-01-01

From mobile, cable-free re-charging of electric vehicles, smart phones and laptops to collecting solar electricity from orbiting solar farms, wireless power transfer (WPT) technologies offer consumers and society enormous benefits. Written by innovators in the field, this comprehensive resource explains the fundamental principles and latest advances in WPT and illustrates key applications of this emergent technology.

PERANCANGAN SISTEM TRANSFER DAYA NIRKABEL UNTUK UNMANNED AERIAL VEHICLE (UAV MICRO JENIS QUADCOPTER

Directory of Open Access Journals (Sweden)

Setyawan Wahyu Pratomo

2016-11-01

Full Text Available Dalam Unmanned Aerial Vehicle ( UAV jenis Quadcopter, sumber catu daya berupa baterai yang hanya mampu bekerja 10-15 menit di udara merupakan permasalahan tersendiri bagi performa Quadcopter. Sedangkan perfomansi dari Quadcopter pada ketinggian yang susah dijangkau, diharapkan peran operator yang selama ini harus mengkoneksikan secara manual kabel charging ke baterai bisa digantikan oleh sistem secara otomatis ketika baterai akan habis. Untuk itu dalam paper ini membahas suatu perancangan sistem transfer daya nirkabel untuk Quadcopter mengisi ulang baterai tanpa bantuan operator dan tidak harus dilakukan pendaratan di atas tanah. Proses isi ulang ( charging baterai bisa dilakukan di atas gedung maupun di landasan yang telah terpasang transfer daya nirkabel. Tujuannya adalah meningkatkan performansi kerja Quadcopter di udara sesuai dengan kegunaanya. Dari perancangan sistem transfer daya nirkabel untuk Unmanned Aerial Vehicle ( UAV jenis Quadcopter mengisi ulang ( charging baterai, diperoleh hasil efisiensi transfer daya terbaik sebesar 62,24% dengan jarak efektif 10 cm. Frekuensi sistem transfer daya nirkabel diperoleh dari rangkaian Colpitss Oscillator sebesar 333,1 KHz dengan menerapkan prinsip induksi elektromagnetik.

Thermal aging of melt-spun NdFeB magnetic powder in hydrogen

Science.gov (United States)

Pinkerton, Frederick E.; Balogh, Michael P.; Ellison, Nicole; Foto, Aldo; Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P.

2016-11-01

High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity Hci of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H2 gas. Expansion of the NdFeB crystal lattice in both ATF and H2 identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets.

Nuclear reactor power for an electrically powered orbital transfer vehicle

Science.gov (United States)

Jaffe, L.; Beatty, R.; Bhandari, P.; Chow, E.; Deininger, W.; Ewell, R.; Fujita, T.; Grossman, M.; Kia, T.; Nesmith, B.

1987-01-01

To help determine the systems requirements for a 300-kWe space nuclear reactor power system, a mission and spacecraft have been examined which utilize electric propulsion and this nuclear reactor power for multiple transfers of cargo between low earth orbit (LEO) and geosynchronous earth orbit (GEO). A propulsion system employing ion thrusters and xenon propellant was selected. Propellant and thrusters are replaced after each sortie to GEO. The mass of the Orbital Transfer Vehicle (OTV), empty and dry, is 11,000 kg; nominal propellant load is 5000 kg. The OTV operates between a circular orbit at 925 km altitude, 28.5 deg inclination, and GEO. Cargo is brought to the OTV by Shuttle and an Orbital Maneuvering Vehicle (OMV); the OTV then takes it to GEO. The OTV can also bring cargo back from GEO, for transfer by OMV to the Shuttle. OTV propellant is resupplied and the ion thrusters are replaced by the OMV before each trip to GEO. At the end of mission life, the OTV's electric propulsion is used to place it in a heliocentric orbit so that the reactor will not return to earth. The nominal cargo capability to GEO is 6000 kg with a transit time of 120 days; 1350 kg can be transferred in 90 days, and 14,300 kg in 240 days. These capabilities can be considerably increased by using separate Shuttle launches to bring up propellant and cargo, or by changing to mercury propellant.

Nuclear reactor power for an electrically powered orbital transfer vehicle

International Nuclear Information System (INIS)

Jaffe, L.; Beatty, R.; Bhandari, P.

1987-01-01

To help determine the systems requirements for a 300-kWe space nuclear reactor power system, a mission and spacecraft have been examined which utilize electric propulsion and this nuclear reactor power for multiple transfers of cargo between low Earth orbit (LEO) and geosynchronous Earth orbit (GEO). A propulsion system employing ion thrusters and xenon propellant was selected. Propellant and thrusters are replaced after each sortie to GEO. The mass of the Orbital Transfer Vehicle (OTV), empty and dry, is 11,000 kg; nominal propellant load is 5000 kg. The OTV operates between a circular orbit at 925 km altitude, 28.5 deg inclination, and GEO. Cargo is brought to the OTV by Shuttle and an Orbital Maneuvering Vehicle (OMV); the OTV then takes it to GEO. The OTV can also bring cargo back from GEO, for transfer by OMV to the Shuttle. OTV propellant is resupplied and the ion thrusters are replaced by the OMV before each trip to GEO. At the end of mission life, the OTV's electric propulsion is used to place it in a heliocentric orbit so that the reactor will not return to Earth. The nominal cargo capability to GEO is 6000 kg with a transit time of 120 days; 1350 kg can be transferred in 90 days, and 14,300 kg in 240 days. These capabilities can be considerably increased by using separate Shuttle launches to bring up propellant and cargo, or by changing to mercury propellant

Subsolidus phase relations of Bi2O3-Nd2O3-CuO

International Nuclear Information System (INIS)

Sun Yezhou

1997-01-01

The subsolidus phase relations of the Bi 2 O 3 -Nd 2 O 3 -CuO ternary system and its binary systems along with crystallographic parameters of the compounds were investigated by X-ray powder diffraction and differential thermal analysis. The room temperature section of the phase diagram of the Bi 2 O 3 -Nd 2 O 3 -CuO system can be divided into two diphase regions and six triphase regions. No ternary compound was found. There exist two solid solutions (α, β) and a compound Bi 0.55 Nd 0.45 O 1.5 in the (Bi 2 O 2 ) 1-x (Nd 2 O 3 ) x system. Both solid solution α (0.05≤x≤0.30) and β (0.53≤x≤0.73) belong to the rhombohedral system (R3m). The lattice parameters represented by a hexagonal cell are a=3.9832(4), c=27.536(5) A for Bi 0.8 Nd 0.2 O 1.5 (α phase) and a=3.8826(3), c=9.727(1) A for Bi 0.4 Nd 0.8 O 1.5 (β phase). The Bi 0.55 Nd 0.45 O 1.5 compound crystallizes in a face-centered cubic (f.c.c.) lattice with a=5.5480(2) A. (orig.)

Studi On Oxidation State Of U In Ba2NdUO6

International Nuclear Information System (INIS)

Firman Windarto, Hendri

1996-01-01

Ba 2 NdUO 6 is not of the important compounds that is formed from a solidification process for high level liquid waste using super high temperature method Ba 2 NdUO 6 has ordered perovskite structure. The objective of this study is to investigate oxidation state of U in Ba 2 NdUO 6 . The properties of Ba 2 NdUO 6 were observed by using Faraday-type torsion magnetometer and X-ray Photoelectron Spectrometer (XPS). The magnetic susceptibility measured in the temperature range of 4K to room temperature showed that the Ba 2 NdUO 6 is paramagnetism that obeys the Curie-Weiss law. The effective moment of Ba 2 NdUO 6 is 3.04 μB. The results of xPs spectrum showed that the peaks of U4f for Ba 2 NdUO 6 appeared exactly between binding energy of UO 2 and UO 3 . It can be concluded that Ba 2 NdUO 6 has binding energy peaks corresponding to pentavalent uranium

Wheeled Vehicle Clutches, Transmissions, and Transfers. Military Curriculum Materials for Vocational and Technical Education.

Science.gov (United States)

Army Ordnance Center and School, Aberdeen Proving Ground, MD.

This course is one of several subcourses that make up the entire Army correspondence course on wheeled vehicle maintenance. The subcourse is designed to provide the student with information about the operation, malfunction diagnosis, maintenance, and repair of wheeled vehicle clutches, transmissions, and transfer cases. It provides the basic…

Magnetic Field Emissions for Ferrite and Non-Ferrite Geometries for Wireless Power Transfer to Vehicles

DEFF Research Database (Denmark)

Batra, Tushar; Schaltz, Erik

2014-01-01

Minimizing magnetic field emissions to surroundings is one of the most challenging design criteria for wireless power transfer to vehicles. In this paper, concept of division of the emissions into three zones (primary, secondary, and combined zone) in the vertical direction is introduced. For geo......Minimizing magnetic field emissions to surroundings is one of the most challenging design criteria for wireless power transfer to vehicles. In this paper, concept of division of the emissions into three zones (primary, secondary, and combined zone) in the vertical direction is introduced...... for vertical separation between the coils in range of 100-180 mm. It is observed that lower vertical separation results in higher overlapping of the zones and the coils behave as they are effectively placed close to center of air gap. The analysis in this work provides a better understanding of the space...... profile of magnetic field emissions (with and without ferrite) for wireless power transfer to vehicles....

Coercivity enhancement in hot deformed Nd2Fe14B-type magnets by doping low-melting RCu alloys (R = Nd, Dy, Nd + Dy)

Science.gov (United States)

Lee, Y. I.; Huang, G. Y.; Shih, C. W.; Chang, W. C.; Chang, H. W.; You, J. S.

2017-10-01

Magnetic properties of the anisotropic NdFeB magnets prepared by hot pressing followed by die-upsetting NdFeB MQU-F powders doped with low-melting RCu alloy powders were explored, where RCu stands for Nd70Cu30, Dy70Cu30 and (Nd0.5Dy0.5)70Cu30, respectively. In addition, the post-annealing at 600 °C was employed to modify the microstructures and the magnetic properties of the hot deformed magnets. It is found that doping RCu alloy powders is effective in enhancing the coercivity of the hot deformed NdFeB magnets from 15.1 kOe to 16.3-19.5 kOe. For Nd70Cu30-doped magnets, the increment of coercivity is only 1.2 kOe. Meanwhile, Dy70Cu30-doped and (Nd0.5Dy0.5)70Cu30-doped magnets show an almost identical enhancement of coercivity of about 4.4 kOe. Importantly, the latter magnet shows a beneficial effect of reducing the usage of Dy from 1.6 wt% to 0.8 wt%. TEM analysis shows that nonmagnetic Nd, Dy and Cu appear at grain boundary and isolate the magnetic grains, leading to an enhancement of coercivity. Doping lower melting point Dy-lean (Nd0.5Dy0.5)70Cu30 powders into commercial MQU-F powders for making high coercivity hot deformed NdFeB magnets might be a potential and economic way for mass production.

Definition of technology development missions for early space stations orbit transfer vehicle serving. Phase 2, task 1: Space station support of operational OTV servicing

Science.gov (United States)

1983-01-01

Representative space based orbital transfer vehicles (OTV), ground based vehicle turnaround assessment, functional operational requirements and facilities, mission turnaround operations, a comparison of ground based versus space based tasks, activation of servicing facilities prior to IOC, fleet operations requirements, maintenance facilities, OTV servicing facilities, space station support requirements, and packaging for delivery are discussed.

Near-UV sensitized 1.06 μm emission of Nd{sup 3+} ions via monovalent copper in phosphate glass

Energy Technology Data Exchange (ETDEWEB)

Jiménez, José A., E-mail: jose.jimenez@unf.edu [Department of Chemistry, University of North Florida, Jacksonville, FL 32224 (United States); Sendova, Mariana [Optical Spectroscopy & Nano-Materials Lab, New College of Florida, Sarasota, FL 34243 (United States)

2015-07-15

Monovalent copper ions effectively incorporated in Nd-containing phosphate glass by a single-step melt-quench method have been established as near-ultraviolet (UV) sensitizers of Nd{sup 3+} ions, resulting in a remarkable {sup 4}F{sub 3/2} → {sup 4}I{sub 11/2} emission at 1.06 μm. The spectroscopic data indicates an efficient energy conversion process. The Cu{sup +} ions first absorb photons broadly around 360 nm, and subsequently transfer the energy from the Stokes-shifted emitting states to resonant Nd{sup 3+} energy levels in the visible. Ultimately, the Nd{sup 3+} electronic excited states decay and the upper lasing state {sup 4}F{sub 3/2} is populated, leading to the enhanced emission at 1.06 μm. The characteristic features of the Cu{sup +} visible emission spectra and the reduced lifetime of the corresponding Cu{sup +} donor states indicate an efficient non-radiative transfer. The Cu{sup +}/Nd{sup 3+} co-doped phosphate glass appears suitable as solid-state laser material with enhanced pump range in the near-UV part of the spectrum and for solar spectral conversion in photovoltaic cells. - Graphical abstract: Display Omitted - Highlights: • Monovalent copper ions effectively stabilized in Nd{sup 3+}-containing phosphate glass. • Enhanced Nd{sup 3+} near-infrared emission observed upon the Cu{sup +} ions incorporation. • Cu{sup +} → Nd{sup 3+} non-radiative energy transfer efficiencies and likely energy transfer pathways evaluated. • Potential for solid-state lasers and solar spectral conversion suggested.

Crystal-field energy level analysis for Nd{sup 3+} ions at the low symmetry C{sub 1} site in [Nd(hfa){sub 4}(H{sub 2}O)](N(C{sub 2}H{sub 5}){sub 4}) single crystals

Energy Technology Data Exchange (ETDEWEB)

Mech, Agnieszka; Gajek, Zbigniew [Institute of Low Temperature and Structure Research, Polish Academy Of Sciences, ulica Okolna 2, 54-422 Wroclaw (Poland); Karbowiak, Miroslaw [Faculty of Chemistry, University of Wroclaw, ulica F Joliot-Curie 14, 50-383 Wroclaw (Poland); Rudowicz, Czeslaw [Institute of Physics, Szczecin University of Technology, Aleja Piastow 17, 70-310 Szczecin (Poland)], E-mail: karb@wchuwr.pl

2008-09-24

Optical absorption measurements of Nd{sup 3+} ions in single crystals of [Nd(hfa){sub 4}(H{sub 2}O)](N(C{sub 2}H{sub 5}){sub 4}) (hfa = hexafluoroacetyloacetonate), denoted Nd(hfa) for short, have been carried out at 4.2 and 298 K. This compound crystallizes in the monoclinic system (space group P 2{sub 1}/n). Each Nd ion is coordinated to eight oxygen atoms that originate from the hexafluoroacetylacetonate ligands and one oxygen atom from the water molecule. A total of 85 experimental crystal-field (CF) energy levels arising from the Nd{sup 3+} (4f{sup 3}) electronic configuration were identified in the optical spectra and assigned. A three-step CF analysis was carried out in terms of a parametric Hamiltonian for the actual C{sub 1} symmetry at the Nd{sup 3+} ion sites. In the first step, a total of 27 CF parameters (CFPs) in the Wybourne notation B{sub kq}, admissible by group theory, were determined in a preliminary fitting constrained by the angular overlap model predictions. The resulting CFP set was reduced to 24 specific independent CFPs using appropriate standardization transformations. Optimizations of the second-rank CFPs and extended scanning of the parameter space were employed in the second step to improve reliability of the CFP sets, which is rather a difficult task in the case of no site symmetry. Finally, seven free-ion parameters and 24 CFPs were freely varied, yielding an rms deviation between the calculated energy levels and the 85 observed ones of 11.1 cm{sup -1}. Our approach also allows prediction of the energy levels of Nd{sup 3+} ions that are hidden in the spectral range overlapping with strong ligand absorption, which is essential for understanding the inter-ionic energy transfer. The orientation of the axis system associated with the fitted CF parameters w.r.t. the crystallographic axes is established. The procedure adopted in our calculations may be considered as a general framework for analysis of CF levels of lanthanide ions at low

Synthesis and characterization of Nd3+: Yb3+ co-doped near infrared sensitive fluorapatite nanoparticles as a bioimaging probe

Science.gov (United States)

Karthi, S.; Kumar, G. A.; Sardar, D. K.; Santhosh, C.; Girija, E. K.

2018-03-01

Trivalent Nd and Yb co-doped rod shaped hexagonal phase fluorapatite (FAP) nanoparticles of length and width about 32 and 13 nm, respectively were prepared by hydrothermal method and investigated the ability for 980 nm emission via Nd3+ → Yb3+ energy transfer with the objective of utilizing them in biomedical imaging. Nd3+ → Yb3+ energy transfer in FAP was studied as a function of both Nd3+ and Yb3+ concentrations and found that when Yb3+ concentration was 10 mol% the FAP phase has partially turned in to YbPO4 phase. The Yb3+ emission intensity at 980 nm significantly increased up to 5 mol% Yb3+ doping and then reduced drastically for further increase in its concentration. Nd3+ →Yb3+ energy transfer rates were evaluated from the decay curves and found that a transfer rate of 71% for 2 mol% Nd3+ co-doped with 5 mol% Yb3+. The cytocompatibility test with fibroblast like cells using MTT assay revealed that the nanoparticles are compatible with the cells.

Orbital transfer vehicle concept definition and system analysis study. Volume 2: OTV concept definition and evaluation. Book 1: Mission and system requirements

Science.gov (United States)

Kofal, Allen E.

1987-01-01

The mission and system requirements for the concept definition and system analysis of the Orbital Transfer Vehicle (OTV) are established. The requirements set forth constitute the single authority for the selection, evaluation, and optimization of the technical performance and design of the OTV. This requirements document forms the basis for the Ground and Space Based OTV concept definition analyses and establishes the physical, functional, performance and design relationships to STS, Space Station, Orbital Maneuvering Vehicle (OMV), and payloads.

Solar Electric Propulsion Technologies Being Designed for Orbit Transfer Vehicle Applications

Science.gov (United States)

Sarver-Verhey, Timothy R.; Hoffman, David J.; Kerslake, Thomas W.; Oleson, Steven R.; Falck, Robert D.

2002-01-01

There is increasing interest in employing Solar Electric Propulsion (SEP) for new missions requiring transfer from low Earth orbit to the Earth-Moon Lagrange point, L1. Mission architecture plans place the Gateway Habitat at L1 in the 2011 to 2016 timeframe. The Gateway Habitat is envisioned to be used for Lunar exploration, space telescopes, and planetary mission staging. In these scenarios, an SEP stage, or "tug," is used to transport payloads to L1--such as the habitat module, lunar excursion and return vehicles, and chemical propellant for return crew trips. SEP tugs are attractive because they are able to efficiently transport large (less than 10,000 kg) payloads while minimizing propellant requirements. To meet the needs of these missions, a preliminary conceptual design for a general-purpose SEP tug was developed that incorporates several of the advanced space power and in-space propulsion technologies (such as high-power gridded ion and Hall thrusters, high-performance thin-film photovoltaics, lithium-ion batteries, and advanced high-voltage power processing) being developed at the NASA Glenn Research Center. A spreadsheet-based vehicle system model was developed for component sizing and is currently being used for mission planning. This model incorporates a low-thrust orbit transfer algorithm to make preliminary determinations of transfer times and propellant requirements. Results from this combined tug mass estimation and orbit transfer model will be used in a higher fidelity trajectory model to refine the analysis.

Design considerations for Mars transfer vehicles using nuclear thermal propulsion

Science.gov (United States)

Emrich, William J.

1995-01-01

The design of a Mars Transfer Vehicle (MTV) utilizing nuclear propulsion will require that careful consideration be given to the nuclear radiation environment in which it will operate. The extremely high neutron and gamma fluxes characteristic of nuclear thermal propulsion systems will cause significant heating of the fluid systems in close proximity to the reactor, especially in the lower propellant tanks. Crew radiation doses are also a concern particularly late in a mission when there is less shielding from the propellant tanks. In this study, various vehicle configuration and shielding strategies were examined and the resulting time dependent radiation fields evaluated. A common cluster of three particle bed reactor (PBR) engines were used in all configurations examined. In general, it appears that long, relatively narrow vehicles perform the best from a radiation standpoint, however, good shield optimization will be critical in maintaining a low radiation environment while minimizing the shield weight penalty.

Low temperature magnetic properties of NdCu2

International Nuclear Information System (INIS)

Hillberg, M.; Wagener, W.; Melo, M.A.C. de; Klauss, H.H.; Litterst, F.J.; Loewenhaupt, W.

1997-01-01

μSR experiments on NdCu 2 give evidence for short range order below 25 K above T N =6.5 K. No signal was detected between 16 K and 1.2 K where neutron scattering reveals an incommensurate spin structure. Below 1.2 K the μSR signal is recovered and shows a rotation with 22 MHz. This is interpreted with a squaring up of Nd spins accompanied by a decrease of magnon excitations which is reflected in a decrease of damping of the muon signal

Wireless Power Transfer to a Microaerial Vehicle with a Microwave Active Phased Array

Directory of Open Access Journals (Sweden)

Shotaro Nako

2014-01-01

Full Text Available A wireless power transfer system using a microwave active phased array was developed. In the system, power is transferred to a circling microaerial vehicle (MAV by a microwave beam of 5.8 GHz, which is formed and directed to the MAV using an active phased array antenna. The MAV is expected to support observation of areas that humans cannot reach. The power beam is formed by the phased array with eight antenna elements. Input power is about 5.6 W. The peak power density at 1,500 mm altitude was 2.63 mW/cm2. The power is sent to a circling MAV. Therefore, the transfer beam should be polarized circularly to achieve a constant power supply independent of its yaw angle. To minimize the polarization loss, a sequentially routed antenna (SRA was applied to the transmitter antenna. Results show that the axial ratio of 0.440 dB was accomplished and that power fluctuation was kept below 1%.

Thermal aging of melt-spun NdFeB magnetic powder in hydrogen

International Nuclear Information System (INIS)

Pinkerton, Frederick E.; Balogh, Michael P.; Ellison, Nicole; Foto, Aldo; Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P.

2016-01-01

High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity H ci of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H 2 gas. Expansion of the NdFeB crystal lattice in both ATF and H 2 identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets. - Highlights: • Injection molded NdFeB magnets age rapidly in automatic transmission fluid (ATF). • Coercivity loss is not due to direct chemical reaction between ATF and the powder. • Chemical reaction with the binder does not play a major role in aging. • Hydrogen dissociates from ATF and diffuses into Nd 2 Fe 14 B, reducing coercivity.

Thermal aging of melt-spun NdFeB magnetic powder in hydrogen

Energy Technology Data Exchange (ETDEWEB)

Pinkerton, Frederick E., E-mail: frederick.e.pinkerton@gm.com [Chemical and Materials Systems Laboratory, General Motors Research and Development Center, Warren, MI 48092 (United States); Balogh, Michael P.; Ellison, Nicole [Chemical and Materials Systems Laboratory, General Motors Research and Development Center, Warren, MI 48092 (United States); Foto, Aldo [Element Materials Technology Wixom, Inc (United States); Sechan, Martin; Tessema, Misle M.; Thompson, Margarita P. [Powertrain Materials/Fluids/AMPPD Engineering and Labs, GFL VE/PT Materials Engineering, General Motors LLC, Pontiac, MI 48340 (United States)

2016-11-01

High energy product neodymium-iron-boron (NdFeB) magnets are the premier candidate for demanding electrified vehicle traction motor applications. Injection molded (IM) or compression molded (CM) magnets made using NdFeB powders are promising routes to improve motor efficiency, cost, and manufacturability. However, IM and CM NdFeB magnets are susceptible to substantial thermal aging losses at motor operating temperatures when exposed to the automatic transmission fluid (ATF) used as a lubricant and cooling medium. The intrinsic coercivity H{sub ci} of NdFeB IM and CM magnets degrades by as much as 18% when aged for 1000 h in ATF at 150 °C, compared to a 3% loss when aged in air. Here we report aging studies of rapidly quenched NdFeB powder in air, ATF, and H{sub 2} gas. Expansion of the NdFeB crystal lattice in both ATF and H{sub 2} identified hydrogen dissociated from the ATF during aging and diffused into the primary NdFeB phase as the probable cause of the coercivity loss of IM and CM magnets. - Highlights: • Injection molded NdFeB magnets age rapidly in automatic transmission fluid (ATF). • Coercivity loss is not due to direct chemical reaction between ATF and the powder. • Chemical reaction with the binder does not play a major role in aging. • Hydrogen dissociates from ATF and diffuses into Nd{sub 2}Fe{sub 14}B, reducing coercivity.

Survey of Modular Military Vehicles: Benefits and Burdens

Science.gov (United States)

2016-01-01

initiated to delve deeper into these issues . TARDEC has initiated a study through the ARC to establish a modeling framework for assessing the...Development and Engineering Center. army-technology.com. (n.d.). Patria AMV armoured modular vehicle, Finland. Retrieved from http://www.army...technology.com/projects/patria/ army-technology.com. (n.d.). Stryker armoured combat vehicle family, United States of America. Retrieved from http://www.army

Luminescence characteristics of Mg2SiO4:Nd

International Nuclear Information System (INIS)

Indira, P.; Subrahmanyam, R.V.; Murthy, K.V.R.

2011-01-01

Thermoluminescence (TL) properties of Magnesium Ortho silicate (2:1) Mg 2 SiO 4 doped with various concentrations of rare earth (Nd) have been studied. The phosphor material were prepared using standard solid state reaction technique and heated specimens at 1100 ± 20 deg C for two hours. 4% Ammonium chloride was used as flux. The received material was grinded in an agate mortar and pestle. The TL exhibited by the Mg 2 SiO 4 with varying concentration of Nd is interesting in nature. It is interesting to note but as the concentration of Nd increases the peak around 125 deg C TL peak intensity increases. But the hump around 200 deg C resolved as TL peak at 253 deg C with high intensity. (author)

Order and disorder in Ca2ND0.90H0.10-A structural and thermal study

International Nuclear Information System (INIS)

Verbraeken, Maarten C.; Suard, Emmanuelle; Irvine, John T.S.

2011-01-01

The structure of calcium nitride hydride and its deuterided form has been re-examined at room temperature and studied at high temperature using neutron powder diffraction and thermal analysis. When synthesised at 600 deg. C, a mixture of both ordered and disordered Ca 2 ND 0.90 H 0.10 phases results. The disordered phase is the minor component and has a primitive rocksalt structure (spacegroup Fm3m) with no ordering of D/N on the anion sites and the ordered phase is best described using the rhombohedral spacegroup R-3m with D and N arranged in alternate layers in (111) planes. This mixture of ordered and disordered phases exists up to 580 deg. C, at which the loss of deuterium yields Ca 2 ND 0.85 with the disappearance of the disordered phase. In the new ordered phase there exists a similar content of vacancies on both anion sites; to achieve this balance, a little N transfers onto the D site, whereas there is no indication of D transferring onto the N-sites. These observations are thought to indicate that the D/N ordering is difficult to achieve with fully occupied anion sites. It has previously been reported that Ca 2 ND has an ordered cubic cell with alternating D and N sites in the [100] directions ; however, for the samples studied herein, there were clearly two coexisting phases with apparent broadening/splitting of the primitive peaks but not for the ordered peaks. The rhombohedral phase was in fact metrically cubic; however, all the observed peaks were consistent with the rhombohedral unit cell with no peaks requiring the larger ordered cubic unit cell to be utilised. Furthermore this rhombohedral cell displays the same form of N-D ordering as the Sr and Ba analogues, which are metrically rhombohedral. - Graphical abstract: Ca 2 ND 0.90 H 0.10 forms a mixture of ordered and disordered phases when synthesised at 600 deg. C. The ordered phase disappears at high temperature upon release of structural deuterium/hydrogen, leaving a single, partially disordered

Solubility of NaNd(CO3)2.6H2O(c) in concentrated Na2CO3 and NaHCO3 solutions

International Nuclear Information System (INIS)

Rao, L.; Rai, D.; Felmy, A.R.; Fulton, R.W.; Novak, C.F.

1996-01-01

NaNd(CO 3 ) 2 x 6 H 2 O(c) was identified to be the final equilibrium solid phase in suspensions containing concentrated sodium carbonate (0.1 to 2.0 M) and sodium bicarbonate (0.1 to 1.0 M), with either NaNd(CO 3 ) 2 x 6 H 2 O(c) or Nd 2 (CO 3 ) 3 x xH 2 O(s) as initial solids. A thermodynamic model, based on Pitzer's specific into-interaction approach, was developed to interpret the solubility of NaNd(CO 3 ) 2 x 6 H 2 O(c) as functions of sodium carbonate and sodium bicarbonate concentrations. In this model, the solubility data of NaNd(CO 3 ) 2 x 6 H 2 O(c) were explained by assuming the formation of NdCO 3 + , Nd(CO 3 ) 2 - and Nd(CO 3 ) 3 3- species and invoking the specific ion interactions between Na + and Nd(CO 3 ) 3 3- . Ion interaction parameters for Na + -Nd(CO 3 ) 3 3- were developed to fit the solubility data. Based on the model calculations, Nd(CO 3 ) 3 3- was the predominant aqueous neodymium species in 0.1 to 2 M sodium carbonate and 0.1 to 1 M sodium bicarbonate solutions. The logarithm of the NaNd(CO 3 ) 2 x 6 H 2 O solubility product (NaNd(CO 3 ) 2 x 6 H 2 O(c)=Na + +Nd 3+ +2 CO 3 2- +6 H 2 O) was calculated to be -21.39. This model also provided satisfactory interpretation of the solubility data of the analogous Am(III) system in less concentrated carbonate and bicarbonate solutions. (orig.)

Heavy vehicle simulator operations: protocol for instrumentation, data collection and data storage - 2nd draft

CSIR Research Space (South Africa)

Jones, DJ

2002-09-01

Full Text Available The instrumentation used is discussed under the relevant sections. Keywords: Accelerated pavement testing (APT), Heavy Vehicle Simulator (HVS) Proposals for implementation: Follow protocol in all future HVS testing. Update as required... future HVS testing. The protocol discusses staffing, site selection and establishment, and data collection, analysis and storage. 1.2. Accelerated Pavement Testing Accelerated Pavement Testing (APT) can be described as a controlled application...

Crystal structure of Nd4Cu2O7

International Nuclear Information System (INIS)

Pederzolli, D.R.; Attfield, J.P.

1998-01-01

The structure of Nd 4 Cu 2 O 7 (A2/m, a = 8.449 A, b = 3.759 A, c = 12.601 A, β = 109.57 ), prepared by topotactic reduction of the high-T c superconductor parent phase Nd 2 CuO 4 , has been determined from time-of-flight neutron powder diffraction data revealing a new oxygen vacancy-ordered arrangement containing cooperatively distorted Cu 2 O 3 planes in which 2- and 4- coordinate Cu - sites are present. (orig.)

Synthesis and Characterization of Nd(3+)-Doped CaF2 Nanoparticles.

Science.gov (United States)

Yuan, Dan; Li, Weiwei; Mei, Bingchu; Song, Jinghong

2015-12-01

The Ca(1-x)F(2+x):Nd(x) nanoparticles were synthesized by chemical direct precipitation method. X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Image analyzer, absorption spectrum and transmittance were taken to characterization the phases, morphologies, sizes, size distribution and optical properties of the samples. The results indicate that the Ca(1-x)F(2+x):Nd(x) samples can be rationally modified in size and morphology by altering the Nd3+ ions doping concentration. With increasing concentration of Nd3+ ions, the particle size decreased from 24 to 14 nm, the intensity of the diffraction peaks decreased, the Ca(1-x)F(2+x):Nd(x) particles aggregated ion of the formed clusters which should have an effect on both speed and orientation of the particles growth. The transmittance of ceramics with a thickness of 2 mm showed that the transmittance can reach 90% when the doping concentration was 5%, which should be profitable for LD pumping.

Autocommander: A Supervisory Controller for Integrated Guidance and Control for the 2nd Generation Reusable Launch Vehicle

Science.gov (United States)

Fisher, J. E.; Lawrence, D. A.; Zhu, J. J.; Jackson, Scott (Technical Monitor)

2002-01-01

This paper presents a hierarchical architecture for integrated guidance and control that achieves risk and cost reduction for NASA's 2d generation reusable launch vehicle (RLV). Guidance, attitude control, and control allocation subsystems that heretofore operated independently will now work cooperatively under the coordination of a top-level autocommander. In addition to delivering improved performance from a flight mechanics perspective, the autocommander is intended to provide an autonomous supervisory control capability for traditional mission management under nominal conditions, G&C reconfiguration in response to effector saturation, and abort mode decision-making upon vehicle malfunction. This high-level functionality is to be implemented through the development of a relational database that is populated with the broad range of vehicle and mission specific data and translated into a discrete event system model for analysis, simulation, and onboard implementation. A Stateflow Autocoder software tool that translates the database into the Stateflow component of a Matlab/Simulink simulation is also presented.

Improved room-temperature-selectivity between Nd and Fe in Nd recovery from Nd-Fe-B magnet

Energy Technology Data Exchange (ETDEWEB)

Kataoka, Y.; Kitagawa, J., E-mail: j-kitagawa@fit.ac.jp [Department of Electrical Engineering, Faculty of Engineering, Fukuoka Institute of Technology, 3-30-1 Wajiro-higashi, Higashi-ku, Fukuoka 811-0295 (Japan); Ono, T.; Tsubota, M. [Physonit Inc., 6-10 Minami-Horikawa, Kaita Aki, Hiroshima 736-0044 (Japan)

2015-11-15

The sustainable society requires the recycling of rare metals. Rare earth Nd is one of rare metals, accompanying huge consumption especially in Nd-Fe-B magnets. Although the wet process using acid is in practical use in the in-plant recycle of sludge, higher selectivity between Nd and Fe at room temperature is desired. We have proposed a pretreatment of corrosion before the dissolution into HCl and the oxalic acid precipitation. The corrosion produces γ-FeOOH and a Nd hydroxide, which have high selectivity for HCl solution at room temperature. Nd can be recovered as Mn{sub 2}O{sub 3}-type Nd{sub 2}O{sub 3}. The estimated recovery-ratio of Nd reaches to 97%.

Improved room-temperature-selectivity between Nd and Fe in Nd recovery from Nd-Fe-B magnet

Directory of Open Access Journals (Sweden)

Y. Kataoka

2015-11-01

Full Text Available The sustainable society requires the recycling of rare metals. Rare earth Nd is one of rare metals, accompanying huge consumption especially in Nd-Fe-B magnets. Although the wet process using acid is in practical use in the in-plant recycle of sludge, higher selectivity between Nd and Fe at room temperature is desired. We have proposed a pretreatment of corrosion before the dissolution into HCl and the oxalic acid precipitation. The corrosion produces γ-FeOOH and a Nd hydroxide, which have high selectivity for HCl solution at room temperature. Nd can be recovered as Mn2O3-type Nd2O3. The estimated recovery-ratio of Nd reaches to 97%.

Implementation Scenarios for Electric Vehicle Roadway Wireless Power Transfer; NREL (National Renewable Energy Laboratory)

Energy Technology Data Exchange (ETDEWEB)

Meintz, A.; Markel, T.; Burton, E.; Wang, L.; Gonder, J.; Brooker, A.

2015-06-05

Analysis has been performed on the Transportation Secure Data Center (TSDC) warehouse of collected GPS second-by-second driving profile data of vehicles in the Atlanta, Chicago, Fresno, Kansas City, Los Angeles, Sacramento, and San Francisco Consolidated Statistical Areas (CSAs) to understand in-motion wireless power transfer introduction scenarios. In this work it has been shown that electrification of 1% of road miles could reduce fuel use by 25% for Hybrid Electric Vehicles (HEVs) in these CSAs. This analysis of strategically located infrastructure offers a promising approach to reduced fuel consumption; however, even the most promising 1% of road miles determined by these seven analysis scenarios still represent an impressive 2,700 miles of roadway to electrify. Therefore to mitigate the infrastructure capital costs, integration of the grid-tied power electronics in the Wireless Power Transfer (WPT) system at the DC-link to photovoltaic and/or battery storage is suggested. The integration of these resources would allow for the hardware to provide additional revenue through grid services at times of low traffic volumes and conversely at time of high traffic volumes these resources could reduce the peak demand that the WPT system would otherwise add to the grid.

Electric vehicle station equipment for grid-integrated vehicles

Science.gov (United States)

Kempton, Willett; Kiamilev, Fouad; McGee, Rodney; Waite, Nick

2017-09-05

Methods, systems, and apparatus transferring power between the grid and an electric vehicle are disclosed. The apparatus may include at least one vehicle communication port for interfacing with electric vehicle equipment (EVE) and a processor coupled to the at least one vehicle communication port to establish communication with the EVE, receive EVE attributes from the EVE, and transmit electric vehicle station equipment (EVSE) attributes to the EVE. Power may be transferred between the grid and the electric vehicle by maintaining EVSE attributes, establishing communication with the EVE, and transmitting the EVSE maintained attributes to the EVE.

Fabrication and spectral properties of Nd, La: CaF2 transparent ceramics

Science.gov (United States)

Xie, Xiaoyu; Mei, Bingchu; Song, Jinghong; Li, Weiwei; Su, Liangbi

2018-02-01

1 at.% Nd: CaF2 nanoparticles doped with different concentrations of La3+ ions (from 0 to 5 at.%) were synthesized by co-precipitation method. Phase identification, morphology of the nanoparticles were investigated by XRD and SEM measurements. The Nd, La: CaF2 ceramics were fabricated by hot-pressed method in the vacuum environment. The transmittance of all the ceramics reached 88% at the wavelength of 1400 nm. The luminescence intensities and decay lifetimes enhanced significantly with the increasing of La3+ concentration. The Nd, La: CaF2 ceramics have broad and flat emission band at 1050 nm with the largest FWHM of 28.16 nm. In addition, the spectrum results indicated that the fluorescence lifetime of Nd, La: CaF2 ceramics was longer than that of the Nd, Y: CaF2 ceramics with the same doping concentration.

Nd-YAG laser welding of bare and galvanised steels

International Nuclear Information System (INIS)

Kennedy, S.C.; Norris, I.M.

1989-01-01

Until recently, one of the problems that has held back the introduction of lasers into car body fabrication has been the difficulty of integrating the lasers with robots. Nd-YAG laser beams can be transmitted through fibre optics which, as well as being considerably easier to manipulate than a mirror system, can be mounted on more lightweight accurate robots. Although previously only available at low powers, recent developments in Nd-YAG laser technology mean that lasers of up to 1kW average power will soon be available, coupled to a fibre optic beam delivery system. The increasing usage of zinc coated steels in vehicle bodies has led to welding problems using conventional resistance welding as well as CO 2 laser welding. The use of Nd-YAG lasers may be able to overcome these problems. This paper outlines work carried out at The Welding Institute on a prototype Lumonics 800W pulsed Nd-YAG laser to investigate its welding characteristics on bare and zinc coated car body steels

Nd(BrO3)3-Yb(BrO3)3-H2O and Nd2(SeO4)3-Yb2(SeO4)3-H2O systems at 25 deg C

International Nuclear Information System (INIS)

Serebrennikov, V.V.; Batyreva, V.A.; Tsybukova, T.N.

1981-01-01

Using the methods of isothermal solubility the Nd(BrO 3 ) 3 - Yb(BrO 3 ) 3 -H 2 O and Nd 2 (SeO 4 ) 3 -Yb 2 (SeO 4 ) 3 -H 2 O systems are studied at 25 deg C. The compositions of the solid phases are determined by the method of ''residues''. The formation of two series of solid solutions in both systems is established. Besides, there is a crystallization region of Nd 2 (SeO 4 ) 3 in the system of selenates. The solubility diagrams of the systems are presented [ru

Prospects for the use of thermionic nuclear power plants for interorbital transfers of space vehicles in near space

International Nuclear Information System (INIS)

Andreev, P.V.; Zhabotinskii, E.E.; Nikonov, A.M.

1993-01-01

In a previous study the authors considered the use of thermionic nuclear power plants with a thermal reactor for interorbital transfers of space vehicles by electrojet propulsion systems (EJPSs), opening up broad prospects for putting payloads into a high orbit with relatively inexpensive means for a launch into a reference orbit, e.g., the Proton launch vehicle. This is of major importance for the commercial use of space technology, in particular, for erecting technological platforms for the production of various materials. In the work reported here the authors continue the study of interorbital transfers and explore the potentialities of thermionic NPPs with a thermal reactor and with a fast reactor. In boosted operation the electrical power of the latter may reach several hundred kilowatts. What type of NPP is desirable for testing an electrojet propulsion system in interorbital transfers from a reference orbit to a high orbit, providing that the time is limited, depends on the class of the launch vehicle characterized by the mass M o that the vehicle can carry into the reference orbit, where radiation safety conditions allow the NPP to be started up. Results of studies are presented that give an idea of the rational choice of type of thermionic NPP for the organization in interorbital transfers

Intrinsic evolution of novel (Nd, MM)2Fe14B-system magnetic flakes

Science.gov (United States)

Yu, Xiaoqiang; Zhu, Minggang; Liu, Weiqiang; Li, Yanfeng; Zhang, Jiuxing; Yue, Ming; Li, Wei

2018-01-01

The Nd-substituted (Nd x MM1- x )-Fe-B strip-casting flakes were prepared by induction melting in the vacuum furnace and then subsequently by strip-casting technology. The microstructure and magnetic properties of (Nd x MM1- x )-Fe-B alloys are related to the Nd substitution. 2:14:1 main phases and minor impure phases coexist in the MM-Fe-B flake. For example, La2O3 and CeFe2 impure phases are obviously detected in the x = 0 specimen. As an increase of the Ce concentration is inversely accompanied with the decrease of the Nd content ( x) in (Nd x MM1- x )2Fe14B main phases (0 ≤ x ≤ 1), XRD analysis shows that the overall diffraction peaks of the main phases shift to right domestically because of smaller radius Ce4+. The melting point, spin reorientation phase transition temperature, Curie temperature, magneto-crystalline anisotropy field (at 300 K), and the magnetization ( M 9T) for MM-Fe-B/(Nd0.4MM0.6)-Fe-B/(Nd0.7MM0.3)-Fe-B/Nd-Fe-B strip-casting alloys are 1376.15/1414.15/1439.15/1458.15 K, 74/113/124/135 K, 493.2/538.4/559.7/582.3 K, 48/55.2/64.4/70.1 kOe and 136.5/143.7/151.5/153.7 emu/g, respectively. Due to the varied composition of hard magnetic main phases, M 9T increases gradually with the increase of Nd content ( x). SEM observation and EDX results demonstrate that more Nd and Pr elements aggregate into the 2:14:1 ferromagnetic phase, while less La and Ce elements are prone to the RE-rich region compared with the nominal ratio. As a result, the growth of M 9T becomes extraordinary under maximum external field 9 T, indicating that the (Nd0.7MM0.3)-Fe-B flake may display relatively good magnetic properties and those with higher Nd content have evident effect on magnetization, compositions, and microstructures of hard magnetic main phases. Therefore, practical application of (Nd x MM1- x )-Fe-B-sintered magnets will be very prospective.

Weight optimization of an aerobrake structural concept for a lunar transfer vehicle

Science.gov (United States)

Bush, Lance B.; Unal, Resit; Rowell, Lawrence F.; Rehder, John J.

1992-01-01

An aerobrake structural concept for a lunar transfer vehicle was weight optimized through the use of the Taguchi design method, finite element analyses, and element sizing routines. Six design parameters were chosen to represent the aerobrake structural configuration. The design parameters included honeycomb core thickness, diameter-depth ratio, shape, material, number of concentric ring frames, and number of radial frames. Each parameter was assigned three levels. The aerobrake structural configuration with the minimum weight was 44 percent less than the average weight of all the remaining satisfactory experimental configurations. In addition, the results of this study have served to bolster the advocacy of the Taguchi method for aerospace vehicle design. Both reduced analysis time and an optimized design demonstrated the applicability of the Taguchi method to aerospace vehicle design.

Abstracts: 2nd interventional MRI symposium

Energy Technology Data Exchange (ETDEWEB)

Anon.

1997-09-01

Main topics of the 2nd interventional MRI symposium were: MR compatibility and pulse sequences; MR thermometry, biopsy, musculoskeletal system; laser-induced interstitial thermotherapy, radiofrequency ablations; intraoperative MR; vascular applications, breast, endoscopy; focused ultrasound, cryotherapy, perspectives; poster session with 34 posters described. (AJ)

Abstracts: 2nd interventional MRI symposium

International Nuclear Information System (INIS)

Anon.

1997-01-01

Main topics of the 2nd interventional MRI symposium were: MR compatibility and pulse sequences; MR thermometry, biopsy, musculoskeletal system; laser-induced interstitial thermotherapy, radiofrequency ablations; intraoperative MR; vascular applications, breast, endoscopy; focused ultrasound, cryotherapy, perspectives; poster session with 34 posters described. (AJ)

UV Thermoluminescence and Phosphorescence Properties of Mg2+ and Nd3+ Doped Nanostructured Al2O3

International Nuclear Information System (INIS)

Bitencourt, J F S; Goncalves, K A; Tatumi, S H; Marcos, P J B

2010-01-01

Mg 2+ and Nd 3+ doped aluminium oxide samples were produced by polymer calcination method. Mg 2+ doped samples did not exhibited significant fluorescence emission, using IR (LED, emission centered at 862nm) or green (Xe-lamp plus optical filter, emission centered at 520 nm) sources. Nonetheless, high thermostimulated luminescence was detected, with high emission peak at 190 0 C. A nanoscopic layer (about 50 nm width) of magnesium spinel was observed by Transmission Electronic Microscopy (TEM) for 2.61mol% doped sample; this layer can be the responsible for TL enhancement. Nd 3+ doped sample exhibited low phosphorescence emission in the UV (Schott U-340) using IR source. TL peaks were detected at 185 and 265 0 C; the intermediary peak showed the highest emission. Occurrence of NdAl and NdAl 2 structures were detected in 5 mol% doped sample and NdAl 2 and NdAl 4 structures in 10 mol% doped sample.

Energy transfer in LaF3: R3+, Pr3+ (where R = Nd, Dy)

International Nuclear Information System (INIS)

Reddy, B.R.; Venkateswarlu, P.

1982-01-01

Fluorescence is observed for 1 D 2 levels of Pr 3+ on exciting the higher lying level 3 P 0 in doubly doped systems LaF 3 : R 3+ , Pr 3+ (R = Nd or Dy) but not in LaF 3 :Pr 3+ . From the recorded excitation spectra, and the measured decay times, it has been found that the drain mechanism of population to 1 D 2 levels is caused in doubly doped systems by ion-pair relaxation between Pr 3+ ( 3 P 0 -- 1 D 2 ) and Nd 3+ (Z-X) or Dy 3+ (Z-Y) ions

Measurement and Evaluation of the Activation Resonance Integral of 146Nd, 148Nd and 150Nd

International Nuclear Information System (INIS)

Ricabarra, M. D.; Turjanski, R.; Ricabarra, G. H.

2012-01-01

Values of the ratio of the reduced activation resonance integral to the thermal cross section, I'/σ 0 of 146 Nd, 148 Nd and 150 Nd were determined relative to gold by measuring cadmium ratios. A lithium-drifted germanium gamma ray spectrometer was used to resolve the activities of the irradiated samples. The results are for 146 Nd I'/σ 0 = 1.42±0.1 0 and with an assumed σ 0 = 1.4 barn, I' = 1 .99±0.20; for 148 Nd I'/ σ 0 = 4.22±0.1 4 and with an assumed σ 0 = 2.5 barn, I' = 10.5±0. 9 barn, and for 150 Nd I'/σ 0 = 13.7±0. 8 and with an assumed σ 0 = 1.2 barn, I' = 16.4±2.8. The resolved and unresolved epithermal integrals of 146 Nd, 148 Nd and 150 Nd were calculated. Values of the spectral correction factor were also calculated, so the resonance integral could be obtained from the epithermal integral data measured in our reactor spectrum in this experiment. Epithermal integral and spectral correction factors are listed in the text. The most important result of this investigation is that the 148 Nd activation reduced resonance integral is about half of the previously recommended value and consequently the radiative width for 148 Nd is also about half of the previously accepted value. (author)

File list: His.Lar.10.AllAg.2nd_instar [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available His.Lar.10.AllAg.2nd_instar dm3 Histone Larvae 2nd instar SRX013087,SRX013015,SRX01...3112,SRX013042,SRX013043,SRX013096 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/His.Lar.10.AllAg.2nd_instar.bed ...

File list: His.Lar.05.AllAg.2nd_instar [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available His.Lar.05.AllAg.2nd_instar dm3 Histone Larvae 2nd instar SRX013087,SRX013096,SRX01...3043,SRX013015,SRX013112,SRX013042 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/His.Lar.05.AllAg.2nd_instar.bed ...

File list: His.Lar.50.AllAg.2nd_instar [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available His.Lar.50.AllAg.2nd_instar dm3 Histone Larvae 2nd instar SRX013015,SRX013042,SRX01...3112,SRX013043,SRX013087,SRX013096 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/His.Lar.50.AllAg.2nd_instar.bed ...

File list: His.Lar.20.AllAg.2nd_instar [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available His.Lar.20.AllAg.2nd_instar dm3 Histone Larvae 2nd instar SRX013015,SRX013042,SRX01...3112,SRX013043,SRX013096,SRX013087 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/His.Lar.20.AllAg.2nd_instar.bed ...

File list: ALL.Lar.05.AllAg.2nd_instar [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available ALL.Lar.05.AllAg.2nd_instar dm3 All antigens Larvae 2nd instar SRX013087,SRX013096,...SRX013043,SRX013015,SRX013112,SRX013042,SRX013113,SRX013016,SRX013114 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/ALL.Lar.05.AllAg.2nd_instar.bed ...

File list: ALL.Lar.50.AllAg.2nd_instar [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available ALL.Lar.50.AllAg.2nd_instar dm3 All antigens Larvae 2nd instar SRX013015,SRX013042,...SRX013112,SRX013016,SRX013114,SRX013043,SRX013087,SRX013096,SRX013113 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/ALL.Lar.50.AllAg.2nd_instar.bed ...

File list: ALL.Lar.20.AllAg.2nd_instar [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available ALL.Lar.20.AllAg.2nd_instar dm3 All antigens Larvae 2nd instar SRX013015,SRX013042,...SRX013112,SRX013043,SRX013016,SRX013114,SRX013096,SRX013087,SRX013113 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/ALL.Lar.20.AllAg.2nd_instar.bed ...

Structure of comorbid psychopathological disorders in patients with type 2nd diabetes mellitus

Directory of Open Access Journals (Sweden)

V. V. Chugunov

2017-04-01

Full Text Available Aim: to identify and explore the structure of comorbid psychopathological disorders in patients with type 2nd diabetes mellitus (DM. Materials and methods: 543 patients with type 2nd DM were included into the study. The average age of patients was (56.2 ± 0.65 years. The patients were divided into three groups according to the severity of DM. The first clinical group (CG-1 included 57 patients with type 2nd DM of mild severity, who was treated in outpatient department; the average age in the group was (51.8 ± 1.28 years. The second clinical group (CG-2 made up of 312 patients with type 2nd DM, moderate severity, they were in inpatient department; the median age of the group was (55.1 ± 1.12 years. The third clinical group (CG-3 included 174 patients with type 2nd DM, severe degrees of severity, they undergone inpatient treatment too; average age in the group was (61.8 ± 0.85 years. Research methods: clinical-anamnesis, clinical- psychopathological, statistical. Research results. The study established the incidence of non-psychotic mental disorders of varying severity in patients with type 2nd DM at the level of 94.11 %, among them, for 91.16 % – of psychogenic origin. Proportional correlation between the severity of type 2nd DM and the absence of comorbid psychopathological manifestations was detected (rs = -0.3416, p < 0.01. It is revealed that the dominant psychopathological syndromes among all patients with type 2nd DM were psychoorganic (62.43 %, dyssomnia (60.86 %, asthenic (55.58 % and anxiety (43.05 % syndromes. Structure of the dominant psychopathological syndromes was established depending on severity of type 2nd DM: in CG-1 dominated dyssomnia (36.84 %, anxiety (31.58 %, psychoorganic (21.05 % syndromes; in CG-2 – psychoorganic (65.38 %, asthenic (40.38 %, dyssomnia (38.46 %, anxiety (37, and 82 % syndromes; in CG-3 – dyssomnia (97.70 %, asthenic (89.08 %, organic mental (70.69 %, anxious 48.28 % syndromes. Significant

Definition of technology development missions for early space station, orbit transfer vehicle servicing. Volume 1: Executive summary

Science.gov (United States)

1983-01-01

Orbital Transfer Vehicle (OTV) servicing study scope, propellant transfer, storage and reliquefaction technology development missions (TDM), docking and berthing TDM, maintenance TDM, OTV/payload integration TDM, combined TDMS design, summary space station accomodations, programmatic analysis, and TDM equipment operational usage are discussed.

Thermoluminescent characteristics of ZrO2:Nd films

International Nuclear Information System (INIS)

Vera B, G.; Rivera M, T.; Azorin N, J.; Falcony G, C.; Garcia H, M.; Martinez S, E.

2002-01-01

In this work it is exposed the obtained results after analysing the photo luminescent and thermoluminescent characteristics of activated zirconium oxide with neodymium (ZrO 2 :Nd) and its possible application in the UV radiation dosimetry. The realized experiments had as objective to study the characteristics such as the optimum thermal erased treatment, the influence of light on the response, the response depending on the wavelength, the fadeout of the information, the temperature effect, the response depending on the time and the recurring of the response. The results show that the ZrO 2 :Nd is a promising material to be used as Tl dosemeter for the UV radiation. (Author)

Heat Transfer Analysis of Thermal Protection Structures for Hypersonic Vehicles

Science.gov (United States)

Zhou, Chen; Wang, Zhijin; Hou, Tianjiao

2017-11-01

This research aims to develop an analytical approach to study the heat transfer problem of thermal protection systems (TPS) for hypersonic vehicles. Laplace transform and integral method are used to describe the temperature distribution through the TPS subject to aerodynamic heating during flight. Time-dependent incident heat flux is also taken into account. Two different cases with heat flux and radiation boundary conditions are studied and discussed. The results are compared with those obtained by finite element analyses and show a good agreement. Although temperature profiles of such problems can be readily accessed via numerical simulations, analytical solutions give a greater insight into the physical essence of the heat transfer problem. Furthermore, with the analytical approach, rapid thermal analyses and even thermal optimization can be achieved during the preliminary TPS design.

Synthesis, structure and properties of layered iron-oxychalcogenides Nd2Fe2Se2−xSxO3

International Nuclear Information System (INIS)

Liu, Y.; Zhang, S.B.; Tan, S.G.; Yuan, B.; Kan, X.C.; Zu, L.; Sun, Y.P.

2015-01-01

A new series of sulfur-substituted iron-oxychalcogenides Nd 2 Fe 2 Se 2−x S x O 3 (0≤x≤0.4) was synthesized by solid state reaction method, and investigated by structure, transport, magnetic and specific heat measurements. The compounds crystallize in the layered tetragonal structure with I4/mmm space group, and show semiconducting behavior. The large discrepancy between the activation energies for conductivity, E ρ (152–202 meV), and thermopower, E S (15.6–39.8 meV), indicates the polaronic transport mechanism of the carrier. The parent compound Nd 2 Fe 2 Se 2 O 3 exhibits a frustrated antiferromagnetic (AFM) ground state, and the S-substitution induces an enhanced ferromagnetic (FM) component and possible increased degree of frustration. - Graphical abstract: The crystal structure of Nd 2 Nd 2 Fe 2 Se 2−x S x O 3 is built up by stacking fluorite-like Nd 2 O 2 layers and anti-CuO 2 -type Fe 2 O(Se/S) 2 layers with Fe 2+ cations coordinated by two in-plane O 2- and four Se 2- above and below the square Fe 2 O plane. - Highlights: • We have synthesized a new series of layered iron-oxychalcogenides Nd 2 Fe 2 Se 2−x S x O 3 . • They crystallize in layered tetragonal structure and show semiconducting behavior. • The transport analysis indicates the polaronic transport mechanism of the carrier. • The parent compound shows a frustrated antiferromagnetic (AFM) ground state. • The S-substitution induces an enhanced ferromagnetic (FM) component

Studies of the energy transfer processes from Er3+ and Ho3+ to Nd3+, Tb3+ or Eu3+ in LiYF4 crystal and ZBLAN glass for the laser media optimization operating near 3μm region

International Nuclear Information System (INIS)

Jagosich, Fabio Henrique

2006-01-01

The energy transfer processes (ET) from the 4 I 13/2 ; 4 I 11/2 levels of Er 3+ and 5 I 6 levels of Ho 3+ ions in LiYF 4 (YLF) crystal and ZBLAN glass to Nd 3+ , Tb 3+ or Eu 3+ deactivators ions were studied. The micro parameters of these energy transfer processes were determined using the overlap integral method, and showed that Eu 3+ ion is the best deactivator of the first excited state of the Ho 3+ in YLF, and Nd 3+ is the best deactivator of the Er 3+ in YLF and ZBLAN materials. The 1.5 and 2.7μm emissions of Er 3+ and 2.1 and 2.9μm fluorescence of Ho 3+ were measured using short laser pulses excitations from a tunable OPO pumped 2w-Nd:YAG laser system. We proposed a criterion for discriminating the energy transfer processes assisted by excitation migration (diffusion or hopping) among donors. It was observed that diffusion model describes the ET process from the second excited state of the donor (Er 3+ or Ho 3+ ) independently of the C D-D /C D-A ratio, while the hopping model can describe the ET process involving the first excited state of donor. We proposed a modification of the hopping model in order to describe the experimental results for systems having C D-D /C D-A ≥ 10. Using the ET parameters, we determined that the best systems for laser action at 3μm are the Ho:Eu:YLF, Ho:Nd:YLF and Er:Nd:YLF systems. On the other hand, we found that Er 3+ doped (1.5 mol%) ZBLAN glasses, single and co-doped with Nd 3+ , Tb 3+ or Eu 3+ , do not show potential for laser action at 2.8μm. The up-conversion processes were studied in Er:YLF systems as a function of the Er 3+ concentration, and the excited state absorption (ESA) and up conversion by energy transfer (ETU) processes were discriminated using a time resolved fluorescence decays. It was observed that 980 nm is the most convenient wavelength for pumping the Er:YLF system for quasi cw laser operation at 2.8μm. The pump-probe technique was used to investigate the lifetime effects in Er:YLF system showing

A decay heat removal methodology for reuseable orbital transfer vehicles

Science.gov (United States)

McDaniel, Patrick J.; Perkins, David R.

1992-07-01

Operation of a nuclear thermal rocket(NTR) as the propulsion system for a reusable orbital transfer vehicle has been considered. This application is the most demanding in terms of designing a multiple restart capability for an NTR. The requirements on a NTR cooling system associated with the nuclear decay heat stored during operation have been evaluated, specifically for a Particle Bed Reactor(PBR) configuration. A three mode method of operation has been identified as required to adequately remove the nuclear decay heat.

Texturing for bulk α-Fe/Nd2Fe14B nanocomposites with enhanced magnetic properties

International Nuclear Information System (INIS)

Lou, L.; Hou, F.C.; Wang, Y.N.; Cheng, Y.; Li, H.L.; Li, W.; Guo, D.F.; Li, X.H.; Zhang, X.Y.

2014-01-01

In the present study, the texturing of bulk α-Fe/Nd 2 Fe 14 B nanocomposites produced from Nd-lean amorphous Nd x Fe 92.5−x Cu 1.5 B 6 (x=9 to 11.5 at%) via a hot deformation under a uniaxial stress of ∼350 MPa at 973 K has been studied. An enhanced (00l) texture of the hard phase is observed with increasing Nd content, which results in an increase in the magnetic anisotropy of the nanocomposite magnets. As a result, both the coercivity and the remanence of the magnets increase simultaneously with increasing Nd content from x=9–11.5 at%, yielding a significant enhancement of the maximum energy product from (BH) max =13.2 to 17.5 MGOe in the direction parallel to stress axis. - Highlights: • Textured bulk α-Fe/Nd 2 Fe 14 B nanocomposites have been produced from Nd-lean alloys. • Nd content has an effect on the texturing of α-Fe/Nd 2 Fe 14 B nanocomposite magnets. • An enhanced (00l) texture of hard phase is observed with increasing Nd content. • Both the coercivity and remanence increase simultaneously with Nd content

Up-conversion luminescence of Er3+/Yb3+/Nd3+-codoped tellurite glasses

International Nuclear Information System (INIS)

Lu Longjun; Nie Qiuhua; Xu Tiefeng; Dai Shixun; Shen Xiang; Zhang Xianghua

2007-01-01

Up-conversion luminescence and energy transfer (ET) processes in Nd 3+ -Yb 3+ -Er 3+ triply doped TeO 2 -ZnO-Na 2 O glasses have been studied under 800 nm excitation. Intense green up-conversion emissions around 549 nm, which can be attributed to the Er 3+ : 4 S 3/2 →4 I 15/2 transition, are observed in triply doped samples. In contrast, the green emissions are hardly observed in Er 3+ singly doped and Er 3+ -Yb 3+ codoped samples under the same condition. Up-conversion luminescence intensity exhibits dependence of Yb 2 O 3 -concentration and Nd 2 O 3 -concentration. Up-conversion mechanism in the triply doped glasses under 800 nm pump is discussed by analyzing the ET among Nd 3+ , Yb 3+ and Er 3+ . And a possible up-conversion mechanism based on sequential ET from Nd 3+ to Er 3+ through Yb 3+ is proposed for green and red up-conversion emission processes

Thermal response of an aeroassisted orbital-transfer vehicle with a conical drag brake

Science.gov (United States)

Pitts, W. C.; Murbach, M. S.

1984-01-01

As an aeroassisted orbital-transfer vehicle (AOTV) goes through an aerobraking maneuver, a significant amount of heat is generated. In this paper, the thermal response of a specific AOTV to this aerobrake heating is examined. The vehicle has a 70 deg, conical drag-brake heat shield attached to a cylindrical body which contains the payload. The heat shield is made of silica fabric. The heat-shield thickness is varied from that of a thin cloth to a 1.5-cm blanket. The fabric thickness, the radiation absorptivity of the vehicle surface materials, and radiation from the wake are all significant parameters in the thermal response to the heating produced by the braking maneuver. The maximum temperatures occur in the vicinity of the interface between the body and the conical heat shield.

Thermal Response of an Aeroassisted Orbital Transfer Vehicle with a Conical Drag Brake

Science.gov (United States)

Pitts, W. C.; Murbach, M. S.

1985-01-01

As an aeroassisted orbital transfer vehicle (AOTV) goes through an aerobraking maneuver a significant amount of heat is generated. In this paper, the thermal response of a specific AOTV to this aerobrake heating is examined. The vehicle has a 70-deg, Conical drag-brake heat shield attached to a cylindrical body which contains the payload. The heat shield is made of ceramic fabric its thickness is varied from that of a thin cloth to a 1.5-cm blanket. The fabric thickness, the radiation absorptivity of the vehicle surface materials, and radiation from the wake are all significant parameters in the thermal response to the heating produced by the braking maneuver. The maximum temperatures occur In the vicinity of the interface between the body and the conical heat shield.

Crystal-field and Nd-Mn exchange interaction in Nd{sub 2/3}Ca{sub 1/3}MnO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Beznosov, A; Fertman, E; Desnenko, V; Loginov, A [B Verkin Institute for Low Temperature Physics and Engineering, NASU, 47 Lenin Ave., 61103 Kharkov (Ukraine); Feher, A; Kajnakova, M, E-mail: fertman@ilt.kharkov.u [Centre of Low Temperature Physics of the Faculty of Science of P.J. Safarik University and IEP SAS, Park Angelinum 9, SK-04154 Kotice (Slovakia)

2010-01-01

A study of the low field magnetization and specific heat in magnetic fields up to 9 T of Nd{sub 2/3}Ca{sub 1/3}MnO{sub 3} perovskite in the 2-30 K temperature range has been done. All the specific heat data show broadened Schottky-like anomaly below 20 K. We suppose that such a behavior originates from the Nd magnetic ordering caused by the splitting of the Nd{sup 3+} ions ground-state doublet (GSD) in the effective molecular field H{sub ex} of Mn spin system supplemented by an applied external magnetic field. The zero field GSD splitting is an evidence of a strong exchange coupling between Nd and Mn magnetic subsystems. The Nd-ions magnetic ordering introduces an additional contribution to the ferromagnetic moment producing anomalies of the field-cooled and zero-field-cooled magnetizations of the system below 28 K. The broadened Schottky-like anomalies found are fitted for every field by a set of three Schottky functions. Applied magnetic field extends the anomaly region and shifts it to the higher temperatures. Splitting of the higher crystal field Kramers doublets gives an additional contribution to the heat capacity under magnetic fields. The GSD g-factors g{sub ||} and g{sub p}erpendicular was estimated as 3.4 and 2.2, respectively, and H{sub ex} as 9 T.

Commensurability oscillations in NdBa2Cu3Oy single crystals

Indian Academy of Sciences (India)

gated by angular dependent magnetization in very pure twinned and twin-free NdBa2 Cu3 Oy single ... The layered structure and the c-axis coherence length, ξc ≈ 4 ˚A, smaller than the lattice ... The high quality of both crystals is demonstrated by ... Commensurability oscillations in NdBa2Cu3Oy single crystals. 2. 3. 4. 5. 6.

ICESat-2 laser Nd:YVO4 amplifier

Science.gov (United States)

Sawruk, Nicholas W.; Burns, Patrick M.; Edwards, Ryan E.; Litvinovitch, Viatcheslav; Martin, Nigel; Witt, Greg; Fakhoury, Elias; Iskander, John; Pronko, Mark S.; Troupaki, Elisavet; Bay, Michael M.; He, Charles C.; Wang, Liqin L.; Cavanaugh, John F.; Farrokh, Babak; Salem, Jonathan A.; Baker, Eric

2018-02-01

We report on the cause and corrective actions of three amplifier crystal fractures in the space-qualified laser systems used in NASA Goddard Space Flight Center's (GSFC) Ice, Cloud, and Land Elevation Satellite-2 (ICESat-2). The ICESat-2 lasers each contain three end-pumped Nd:YVOO4 amplifier stages. The crystals are clamped between two gold plated copper heat spreaders with an indium foil thermal interface material, and the crystal fractures occurred after multiple years of storage and over a year of operational run-time. The primary contributors are high compressive loading of the NdYVO4 crystals at the beginning of life, a time dependent crystal stress caused by an intermetallic reaction of the gold plating and indium, and slow crack growth resulting in a reduction in crystal strength over time. An updated crystal mounting scheme was designed, analyzed, fabricated and tested. Thee fracture slab failure analysis, finite-element modeling and corrective actions are presented.

Orbits 2nd order singularity-free solutions

CERN Document Server

Xu, Guochang

2014-01-01

In its 2nd edition, this book covers the theory of satellite orbits, derives the complete solutions of orbital disturbances, describes the algorithms of orbits determination and the applications of the theory to the phenomenon of physical satellite formation.

Passive Shielding Effect on Space Profile of Magnetic Field Emissions for Wireless Power Transfer to Vehicles

DEFF Research Database (Denmark)

Batra, Tushar; Schaltz, Erik

2015-01-01

Magnetic fields emitted by wireless power transfer systems are of high importance with respect to human safety and health. Aluminum and ferrite are used in the system to reduce the fields and are termed as passive shielding. In this paper, the influence of these materials on the space profile has...... fields for wireless power transfer for vehicle applications....

An analytical optimization method for electric propulsion orbit transfer vehicles

International Nuclear Information System (INIS)

Oleson, S.R.

1993-01-01

Due to electric propulsion's inherent propellant mass savings over chemical propulsion, electric propulsion orbit transfer vehicles (EPOTVs) are a highly efficient mode of orbit transfer. When selecting an electric propulsion device (ion, MPD, or arcjet) and propellant for a particular mission, it is preferable to use quick, analytical system optimization methods instead of time intensive numerical integration methods. It is also of interest to determine each thruster's optimal operating characteristics for a specific mission. Analytical expressions are derived which determine the optimal specific impulse (Isp) for each type of electric thruster to maximize payload fraction for a desired thrusting time. These expressions take into account the variation of thruster efficiency with specific impulse. Verification of the method is made with representative electric propulsion values on a LEO-to-GEO mission. Application of the method to specific missions is discussed

Luminescence properties of Yb:Nd:Tm:KY3F10 nanophosphor and thermal treatment effects

International Nuclear Information System (INIS)

Gomes, Laércio; Linhares, Horácio Marconi da Silva M.D.; Ichikawa, Rodrigo Uchida; Martinez, Luis Gallego; Ranieri, Izilda Marcia

2015-01-01

In this work, we present the spectroscopic properties of KY 3 F 10 (KY3F) nanocrystals activated with thulium and codoped with ytterbium and neodymium ions. The most important processes that lead to the thulium upconversion emissions in the blue region were identified. A time-resolved luminescence spectroscopy technique was employed to measure the luminescence decays and to determine the most important mechanisms involved in the upconversion process that populates 1 G 4 (Tm 3+ ) excited states. Analysis of the energy-transfer processes dynamics using selective pulsed-laser excitations in Yb:Nd:Tm, Nd:KY3F nanocrystals shows that the direct energy transfer from Nd 3+ to Tm 3+ ions is the mechanism responsible for the 78% of the blue upconversion luminescence in the Yb:Nd:Tm:KY3F when compared with the Yb:Nd:Tm:KY3F bulk crystal for an laser excitation at 802 nm. An investigation of the 1 G 4 level luminescence kinetic of Tm 3+ in Yb/Nd/Tm system revealed that the luminescence efficiency ( 1 G 4 ) starts with a very low value (0.38%) for the synthesized nanocrystal (as grown) and strongly increases to 97% after thermal treatment at 550 °C for 6 h under argon flow. As a consequence of the thermal treatment at T=550 °C, the contributions of the (Nd×Tm) (Up 1 ) and (Nd×Yb×Tm) (Up 2 ) upconversion processes to the 1 G 4 luminescence are 33% (Up 1 ) and 67% for Up 2 . Up 2 process represented by Nd 3+ ( 4 F 3/2 )→Yb 3+ ( 2 F 7/2 ) followed by Yb 3+ ( 2 F 5/2 )→Tm ( 3 H 4 )→Tm 3+ ( 1 G 4 ) was previously reported as the main mechanism to produce the blue luminescence in Yb:Nd:Tm:YLiF 4 and KY 3 F 10 bulk crystals. Results of X-ray diffraction analysis of nanopowder using the Rietveld method reveled that crystallite sizes remain unchanged (12–14 nm) after thermal treatments with T≤400 °C, while the 1 G 4 luminescence efficiency strongly increases from 0.38% (T=25 °C) to 12% (T=400 °C). Results shown that the Nd 3+ ions distribution has a concentration

Nd2(SeO3)2(SeO4) . 2H2O - a mixed-valence compound containing selenium in the oxidation states +IV and +VI

International Nuclear Information System (INIS)

Berdonosov, P.S.; Dityat'yev, O.A.; Dolgikh, V.A.; Schmidt, P.; Ruck, Michael; Lightfoot, P.

2004-01-01

Pale pink crystals of Nd 2 (SeO 3 ) 2 (SeO 4 ) . 2H 2 O were synthesized under hydrothermal conditions from H 2 SeO 3 and Nd 2 O 3 at about 200 C. X-ray diffraction on powder and single-crystals revealed that the compound crystallizes with the monoclinic space group C 2/c (a = 12.276(1) A, b = 7.0783(5) A, c = 13.329(1) A, β = 104.276(7) ). The crystal structure of Nd 2 (SeO 3 ) 2 (SeO 4 ) . 2H 2 O is an ordered variant of the corresponding erbium compound. Eight oxygen atoms coordinate the Nd III atom in the shape of a bi-capped trigonal prism. The oxygen atoms are part of pyramidal (Se IV O 3 ) 2- groups, (Se VI O 4 ) 2- tetrahedra and water molecules. The [NdO 8 ] polyhedra share edges to form chains oriented along [010]. The selenate ions link these chains into layers parallel to (001). The layers are interconnected by the selenite ions into a three-dimensional framework. The dehydration of Nd 2 (SeO 3 ) 2 (SeO 4 ) . 2H 2 O starts at 260 C. The thermal decomposition into Nd 2 SeO 5 , SeO 2 and O 2 at 680 C is followed by further loss of SeO 2 leaving cubic Nd 2 O 3 . (Abstract Copyright [2004], Wiley Periodicals, Inc.) [de

Experimental Investigation and Thermodynamic Modeling of the B2O3-FeO-Fe2O3-Nd2O3 System for Recycling of NdFeB Magnet Scrap

Science.gov (United States)

Jakobsson, Lars Klemet; Tranell, Gabriella; Jung, In-Ho

2017-02-01

NdFeB magnet scrap is an alternative source of neodymium that could have a significantly lower impact on the environment than current mining and extraction processes. Neodymium can be readily oxidized in the presence of oxygen, which makes it easy to recover neodymium in oxide form. Thermochemical data and phase diagrams for neodymium oxide containing systems is, however, very limited. Thermodynamic modeling of the B2O3-FeO-Fe2O3-Nd2O3 system was hence performed to obtain accurate phase diagrams and thermochemical properties of the system. Key phase diagram experiments were also carried out for the FeO-Nd2O3 system in saturation with iron to improve the accuracy of the present modeling. The modified quasichemical model was used to describe the Gibbs energy of the liquid oxide phase. The Gibbs energy functions of the liquid phase and the solids were optimized to reproduce all available and reliable phase diagram data, and thermochemical properties of the system. Finally the optimized database was applied to calculate conditions for selective oxidation of neodymium from NdFeB magnet waste.

XMCD study of the Ruddlesden-Popper phase La1.2Nd0.2Sr1.6Mn2O7

International Nuclear Information System (INIS)

Weigand, F.; Goering, E.; Geissler, J.; Justen, M.; Ruck, K.; Schuetz, G.; Doerr, K.

2001-01-01

X-ray Magnetic Circular Dichroism (XMCD) measurements of the Ruddlesden-Popper Phase La 1.2 Nd 0.2 Sr 1.6 Mn 2 O 7 are reported. The Mn K, La and Nd L 2 , 3 edges have been measured on a powder sample at two different magnetic fields at low temperature. The analysis of the spectra at B = 1T indicates a large orbital moment of the Nd 5d-states and a significant spin-polarization of the La 5d-band. Furthermore at the Mn Κ-edge a XMCD-signal is observed, showing a polarization of the Mn 4p-band. At lower field (0.2T) all XMCD-signals are about two times smaller corresponding to the lower total magnetization. The signal at the Nd L 2 edge vanishes completely at 0.2T. (au)

Effects of Nd-addition on the structural, hydrogen storage, and electrochemical properties of C14 metal hydride alloys

Energy Technology Data Exchange (ETDEWEB)

Wong, D.F. [BASF/Battery Materials-Ovonic, 2983 Waterview Drive, Rochester Hills, MI 48309 (United States); Department of Chemical Engineering, Wayne State University, Detroit, MI 48202 (United States); Young, K., E-mail: kwo.young@basf.com [BASF/Battery Materials-Ovonic, 2983 Waterview Drive, Rochester Hills, MI 48309 (United States); Department of Chemical Engineering, Wayne State University, Detroit, MI 48202 (United States); Nei, J.; Wang, L. [BASF/Battery Materials-Ovonic, 2983 Waterview Drive, Rochester Hills, MI 48309 (United States); Ng, K.Y.S. [Department of Chemical Engineering, Wayne State University, Detroit, MI 48202 (United States)

2015-10-25

Nd-addition to the AB{sub 2}-based alloy Ti{sub 12}Zr{sub 22.8−x}V{sub 10}Cr{sub 7.5}Mn{sub 8.1}Co{sub 7.0}Ni{sub 32.2}Al{sub 0.4}Nd{sub x} is studied for its effects on the structure, gaseous-phase hydrogen storage, and electrochemical properties. This study follows a series of Cu, Mo, Fe, Y, Si, and La doping studies in similar AB{sub 2}-based alloys. Limited solubility of Nd in the main Laves phase promotes the formation of secondary phases (AB and Zr{sub 7}Ni{sub 10}) to provide catalytic effects and synergies for improved capacity and high-rate dischargeability (HRD) performance. The main C14 storage phase has smaller lattice constants and cell volumes, and these effects reduce the storage capacity at higher Nd levels. Different hydrogen absorption mechanisms can occur in these multi-component, multi-phase alloys depending on the interfaces of the phases, and they have effects on the alloy properties. Higher Nd-levels improve the HRD performance despite having lower bulk diffusion and surface exchange current. Magnetic susceptibility measurements indicate large percentage of larger metallic nickel clusters are present in the surface oxide of alloys with higher Nd-content, and AC impedance studies show very low charge-transfer resistance with high catalytic capability in the alloys. The −40 °C charge-transfer resistance of 8.9 Ω g in this Nd-series of alloys is the lowest measured out of the studies investigating doped AB{sub 2}-based MH alloys for improved low-temperature characteristics. The improvement in HRD and low-temperature performance appears to be related to the proportion of the highly catalytic NdNi-phase at the surface, which must offset the increased bulk diffusion resistance in the alloy. - Graphical abstract: Schematics of hydrogen flow and corresponding PCT isotherms in funneling mode. - Highlights: • Structural and hydrogen storage properties of Nd-substituted AB{sub 2} metal hydride are reported. • Nd contributes to the lowest

Single NdPc2 molecules on surfaces. Adsorption, interaction, and molecular magnetism

International Nuclear Information System (INIS)

Fahrendorf, Sarah

2013-01-01

They have huge potential for application in molecular-spin-transistors, molecular-spinvalves, and molecular quantum computing. SMMs are characterized by high spin ground states with zero-field splitting leading to high relaxation barriers and long relaxation times. A relevant class of molecules are the lanthanide double-decker phthalocyanines (LaPc 2 ) with only one metal atom sandwiched between two organic phthalocyanine (Pc) ligands. For envisaged spintronic applications it is important to understand the interaction between the molecules and the substrate and its influence on the electronic and magnetic properties. The subject of this thesis is the investigation of the adsorbed neodymium double-decker phthalocyanine (NdPc 2 ) by means of low temperature scanning tunneling microscopy and spectroscopy (STM and STS). The molecules are deposited by sublimation onto different substrates. It is observed that a large fraction of the double-decker molecules decomposes during deposition. The decomposition probability strongly depends on the chosen substrate. Therefore it is concluded that the substrate modifies the electronic structure of the molecule leading to a stabilization or destabilization of the molecular entity. Charge transfer from the surface to the molecule is identified as a potential stabilizing mechanism. The electronic and magnetic properties are investigated in detail for adsorbed NdPc 2 molecules on Cu(100). The results of the experimental study are compared to state-of-the-art density functional theory calculations performed by our colleagues from the Peter Gruenberg Institute (PGI-1) at the Forschungszentrum Juelich. Interestingly, the lower Pc ring of the molecule hybridizes intensely with the substrate leading to strong chemisorption of the molecule, while the upper Pc ring keeps its molecular type electronic states, which can be energetically shifted by an external electric field. Importantly, it is possible to get direct access to the spin

A neodymium(III)-ammonium complex involving oxalate and carbonate ligands: (NH4)2[Nd2(C2O4)3(CO3)(H2O)].H2O.

Science.gov (United States)

Trombe, Jean-Christian; Galy, Jean; Enjalbert, Renée

2002-10-01

The title compound, diammonium aqua-mu-carbonato-tri-mu-oxalato-dineodymium(III) hydrate, (NH(4))(2)[Nd(2)(CO(3))(C(2)O(4))(3)(H(2)O)].H(2)O, involving the two ligands oxalate and carbonate, has been prepared hydrothermally as single crystals. The Nd atoms form a tetranuclear unit across the inversion centre at (1/2, 1/2, 1/2). Starting from this tetranuclear unit, the oxalate ligands serve to develop a three-dimensional network. The carbonate group acts as a bis-chelating ligand to two Nd atoms, and is monodentate to a third Nd atom. The oxalate groups are all bis-chelating. The two independent Nd atoms are ninefold coordinated and the coordination polyhedron of these atoms is a distorted monocapped antiprism.

Chronology of the 1st–2nd Century Graves from the Tarasovo Burial Ground

Directory of Open Access Journals (Sweden)

Goldina Rimma D.

2016-03-01

Full Text Available The article focuses on the chronology of graves dating back to the early (1st – 2nd centuries AD – Nyrgynda stage of the 1st – 5th century Tarasovo burial ground, a classical monument attributed to the Cheganda culture of the Pyany Bor cultural-historical community. Cultural stratigraphy is applied as a research method. Artifacts from the early stage were correlated for 37 male and 102 female complexes, separately. The analysis of grave goods from male burials showed the following three chronological groups, that can be distinguished at the Nyrgynda stage: 1st century (group 1, 2nd century (group 2 and 1st – 2nd centuries AD (group 3. The goods from female graves are more representative and various, so three more groups with shorter chronological lives can be singled out: the fi rst half of the 2nd century (group 2а, the second half of the 2nd century (group 2б and the 1st – fi rst half of the 2nd century (group 4. Certainly, the suggested chronology leaves room for any eventual corrections subject to new findings.

Particularly compliance violations in patients with diabetes mellitus of 2nd type

Directory of Open Access Journals (Sweden)

V. V. Chugunov

2017-04-01

Full Text Available Aim: to investigate and establish the specific complains violations in patients with diabetes mellitus (DM of 2nd type. Materials and methods: 543 patients with DM of 2nd type were examined; the disease duration ranged from 2 to 27 years, average – (14.58 ± 1.82 years. Research methods: clinical-anamnestic, clinical-psychopathological, psycho diagnostic, statistical. Research results. We found that compliance to therapy in patients with DM of 2nd type was broken in 90.49 % of cases. We highlighted three options for compliance violations to DM therapy of 2nd type: dismedication (to 68.14 %, disdiet (88.40 % and disexercise (90.49 %. The sub-variants of dismedication compliance violations to DM therapy of 2nd type was hyper-curation type (8.29 %, which was developed according to surplus of appointments execution and hypo-curation type (59.85 %, which was developed according to deficiency of appointments execution. Among them it was possible to distinguish a third – mixed version (7.37 %, which brings together episodes of the surplus and the deficit of medical drugs usage. The sub-options of disdiet option of compliance violations was hyper-curation type (1.66 %, which manifested itself in pathologically excessive rejection of food and hypo-curation type (86.74 %, which manifested itself in a disregard for the restrictions in the diet. Disexercise variant of compliance violations was possible to divide into hyper-curation type (4,24 %, manifested in excessive physical activity and, in its turn, had three subtypes – inceptional (1.66 %, sub-hyper-curation (1.10 % and procurationis (1.47 %, and hypo-curation type of compliance violations (87.48 %, which manifested itself in a disregard of physical exertion. Dominance of disdiet and disexercise compliance violations among patients with DM of 2nd type (χ2 = 117.258, p < 0.01, dismedication option among patients of all hyper-curation types of compliance violations with DM of 2nd type (χ2 = 26

Fluorescence and Nonradiative Properties of Nd3+ in Novel Heavy Metal Contained Fluorophosphate Glass

Directory of Open Access Journals (Sweden)

Ju H. Choi

2007-01-01

Full Text Available We demonstrate new series of heavy metal containing fluorophosphate glass system. The fluorescence and nonradiative properties of Nd3+ ions are investigated as a function of Nd2O3 concentration. The variation of intensity parameters Ω2, Ω4, and Ω6 is determined from absorption spectra. The spontaneous probability (A and branching ratio (β are determined using intensity parameters. The emission cross sections for the 4F3/2→4I13/2 transition, which is calculated by Fuchtbabauer-Ladenburg method, decrease from 6.1×10−21 to 3.0×10−21(pm2 and those for the 4F3/2→4I11/2 transition decrease from 3.51×10−20 to 1.7×10−20 as Nd2O3 concentration increase up to 3 wt%. The nonradiative relaxation is analyzed in terms of multiphonon relaxation and concentration quenching due to energy transfer among Nd3+ ions. Finally, the above results obtained at 1 wt %Nd2O3 are compared with some of reported laser host glasses which indicated the potentials for broadband-amplifiers and high-power laser applications.

UCP2 muscle gene transfer modifies mitochondrial membrane potential.

Science.gov (United States)

Marti, A; Larrarte, E; Novo, F J; Garcia, M; Martinez, J A

2001-01-01

The aim of this work was to evaluate the effect of uncoupling protein 2 (UCP2) muscle gene transfer on mitochondrial activity. Five week-old male Wistar rats received an intramuscular injection of plasmid pXU1 containing UCP2 cDNA in the right tibialis anterior muscles. Left tibialis anterior muscles were injected with vehicle as control. Ten days after DNA injection, tibialis anterior muscles were dissected and muscle mitochondria isolated and analyzed. There were two mitochondrial populations in the muscle after UCP2 gene transfer, one of low fluorescence and complexity and the other, showing high fluorescence and complexity. UCP2 gene transfer resulted in a 3.6 fold increase in muscle UCP2 protein levels compared to control muscles assessed by Western blotting. Furthermore, a significant reduction in mitochondria membrane potential assessed by spectrofluorometry and flow cytometry was observed. The mitochondria membrane potential reduction might account for a decrease in fluorescence of the low fluorescence mitochondrial subpopulation. It has been demonstrated that UCP2 muscle gene transfer in vivo is associated with a lower mitochondria membrane potential. Our results suggest the potential involvement of UCP2 in uncoupling respiration. International Journal of Obesity (2001) 25, 68-74

The Nd-Mn exchange interaction, low temperature specific heat and magnetism of Nd{sub 2/3}Ca{sub 1/3}MnO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Beznosov, Anatoly [B. Verkin Institute for Low Temperature Physics and Engineering NASU, 47 Lenin Avenue, Kharkov 61103 (Ukraine); Fertman, Elena, E-mail: fertman@ilt.kharkov.ua [B. Verkin Institute for Low Temperature Physics and Engineering NASU, 47 Lenin Avenue, Kharkov 61103 (Ukraine); Desnenko, Vladimir [B. Verkin Institute for Low Temperature Physics and Engineering NASU, 47 Lenin Avenue, Kharkov 61103 (Ukraine); Kajnakova, Marcela; Feher, Alexander [Centre of Low Temperature Physics of the Faculty of Science UPJS and IEP SAS, Park Angelinum 9, 04154 Kosice (Slovakia)

2011-10-15

The low temperature specific heat and magnetic characteristics of Nd{sub 2/3}Ca{sub 1/3}MnO{sub 3} perovskite are studied in a wide range of magnetic fields (up to 9 T). Temperature dependent specific heat data show a broadened Schottky-like anomaly below 20 K caused by splitting of the Nd{sup 3+} ions ground-state doublet in the effective molecular field H{sub ex}, determined by exchange interaction between Nd and Mn spin systems supplemented by an applied external magnetic field. Existence of the splitting at zero magnetic field and expressed field dependence is the evidence of a strong exchange coupling between Nd and Mn magnetic subsystems. The Nd-ions magnetic ordering leads to an additional contribution to the magnetic moment of the system below 30 K, producing anomalies of the magnetic loss and field-cooled and zero-field-cooled magnetizations. The observed broadened Schottky-like anomalies are fitted for each applied magnetic field by the sum of three Schottky functions. Applied magnetic field extends the anomaly region and shifts it to higher temperatures. Splitting of the higher crystal field Kramers doublets gives an additional contribution to the heat capacity in magnetic fields. The ground state doublet g-factors g{sub ||} and g{sub perpendicular} were estimated to be 3.4 and 2.2, respectively, and H{sub ex} was estimated to be 9 T. The Nd{sup 3+} ions magnetic moment estimated from the magnetization data agrees with the value obtained from the specific heat data. - Highlights: > Low temperature specific heat of Nd{sub 2/3}Ca{sub 1/3}MnO{sub 3} has been measured in magnetic fields up to 9 T. > Schottky-like anomalies are fitted for each magnetic field by a sum of three Schottky functions. > An effective magnetic field of the Mn spin system on Nd ion has been estimated as H{sub ex}=9 T. > Nd{sup 3+} ground-state g-factors have been estimated as g{sub ||}=3.4 and g{sub perpendicular} =2.2. > Magnetic ordering of the Nd subsystem has been revealed below

Study of VUV emission and γ-ray responses of Nd:BaF2 scintillaotor

International Nuclear Information System (INIS)

Yanagida, Takayuki; Kawaguchi, Noriaki; Yokota, Yuui; Ishidu, Sumito; Fukuda, Kentaro; Yoshikawa, Akira; Pejchal, Jan; Nikl, Martin; Babin, Vladimir; Sekiya, Hiroyuki; Kamada, Kei

2010-01-01

Nd 3+ 1%, 5% and 10% doped BaF 2 single crystals were grown by the micro-pulling down method. Photoluminescence properties, including excitation and emission spectra and luminescence decay were measured under synchrotron radiation excitation at the Superlumi station in HASYLAB at DESY (Hamburg, Germany). The Nd 3+ related 5d-4f emission lines peaking around 180 nm, 230 nm, and 260 nm, identified as the 5d- 4 I j , 5d- 4 F j , and 5d- 2 G j transitions, were observed under 140-168 nm excitation. In photoluminescence decay under the 160 nm excitation, the dominant component decay time is about 12, 2.5 and 1.2 ns for Nd 3+ 1%, 5% and 10% concentration, respectively. The decay time shortening is explained by the concentration quenching effect. Transmittance of Nd1% sample is about 80% for wavelengths above 185 nm. Finally, gamma-ray responses, non-proportionality and energy resolution of Nd1% sample were compared with the undoped BaF 2 scintillator. The light yield of the Nd1%:BaF 2 is about 93% of that of undoped BaF 2 .

Neutron investigation of Ru-doped Nd1/2Ca1/2MnO3. Comparison with Cr-doped Nd1/2Ca1/2MnO3

International Nuclear Information System (INIS)

Moritomo, Yutaka; Nonobe, Toshihiko; Machida, Akihiko; Ohoyama, Kenji

2002-01-01

Lattice and magnetic properties are investigated for 3% Ru- and Cr-doped Nd 1/2 Ca 1/2 MnO 3 . The parent Nd 1/2 Ca 1/2 MnO 3 is a charge-ordered insulator (T CO =250K). With decreasing temperature below ≅210K, these compounds are separated into two perovskite phases, that is, the long-c and short-c phases. The long-c region shows a ferromagnetic transition at T C ≅210K for the Ru-doped compound and ≅130K for the Cr-doped compound, while the short-c region shows antiferromagnetic transition at T N ≅150K for Ru and ≅110K for Cr. We discuss the origin of the enhanced T C for the Ru-doped compound in terms of the effective one-electron bandwidth W of the e g -band. (author)

Study on heat transfer from hot water to air with evaporation. 2nd report

International Nuclear Information System (INIS)

Yamaji, Tatsuya; Hirota, Tatsuya; Koizumi, Yasuo; Murase, Michio

2013-01-01

Heat transfer from hot water flow to cold air flow was examined. In the present study, the air flow was in turbulent flow condition. When the heat flux from the water flow to the air flow is divides into two terms of an evaporation term and a convection term, the evaporation term is much higher than the convection term; approximately 80 ∼ 60% of the total heat flux since latent heat is taken into the air flow by evaporating vapor. The convection term was approximately two times of the single-phase heat transfer rate with no evaporation. By making use of the analogy between the mass transfer and the heat transfer, and the single-phase heat transfer correlation, the predicting method of the heat transfer rate with the evaporation was developed. (author)

An efficient wireless power transfer system with security considerations for electric vehicle applications

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhen; Chau, K. T., E-mail: ktchau@eee.hku.hk; Liu, Chunhua; Qiu, Chun; Lin, Fei [Department of Electrical and Electronic Engineering, The University of Hong Kong, Pokfulam Road, Hong Kong (China)

2014-05-07

This paper presents a secure inductive wireless power transfer (WPT) system for electric vehicle (EV) applications, such as charging the electric devices inside EVs and performing energy exchange between EVs. The key is to employ chaos theory to encrypt the wirelessly transferred energy which can then be decrypted by specific receptors in the multi-objective system. In this paper, the principle of encrypted WPT is first revealed. Then, computer simulation is conducted to validate the feasibility of the proposed system. Moreover, by comparing the WPT systems with and without encryption, the proposed energy encryption scheme does not involve noticeable power consumption.

An efficient wireless power transfer system with security considerations for electric vehicle applications

International Nuclear Information System (INIS)

Zhang, Zhen; Chau, K. T.; Liu, Chunhua; Qiu, Chun; Lin, Fei

2014-01-01

This paper presents a secure inductive wireless power transfer (WPT) system for electric vehicle (EV) applications, such as charging the electric devices inside EVs and performing energy exchange between EVs. The key is to employ chaos theory to encrypt the wirelessly transferred energy which can then be decrypted by specific receptors in the multi-objective system. In this paper, the principle of encrypted WPT is first revealed. Then, computer simulation is conducted to validate the feasibility of the proposed system. Moreover, by comparing the WPT systems with and without encryption, the proposed energy encryption scheme does not involve noticeable power consumption

An efficient wireless power transfer system with security considerations for electric vehicle applications

Science.gov (United States)

Zhang, Zhen; Chau, K. T.; Liu, Chunhua; Qiu, Chun; Lin, Fei

2014-05-01

This paper presents a secure inductive wireless power transfer (WPT) system for electric vehicle (EV) applications, such as charging the electric devices inside EVs and performing energy exchange between EVs. The key is to employ chaos theory to encrypt the wirelessly transferred energy which can then be decrypted by specific receptors in the multi-objective system. In this paper, the principle of encrypted WPT is first revealed. Then, computer simulation is conducted to validate the feasibility of the proposed system. Moreover, by comparing the WPT systems with and without encryption, the proposed energy encryption scheme does not involve noticeable power consumption.

PREFACE: 32nd UIT (Italian Union of Thermo-fluid-dynamics) Heat Transfer Conference

Science.gov (United States)

2014-11-01

The annual Conference of the ''Unione Italiana di Termofluidodinamica'' (UIT) aims to promote cooperation in the field of heat transfer and thermal sciences by bringing together scientists and engineers working in related areas. The 32nd UIT Conference was held in Pisa, from the 23rd to the 25th of June, 2014 in the buildings of the School of Engineering, just a few months after the celebration of the 100th anniversary of the first Institution of the School of Engineering at the University of Pisa. The response was very good, with more than 100 participants and 80 high-quality contributions from 208 authors on seven different heat transfer related topics: Heat transfer and efficiency in energy systems, environmental technologies, and buildings (25 papers); Micro and nano scale thermo-fluid dynamics (9 papers); Multi-phase fluid dynamics, heat transfer and interface phenomena (14 papers); Computational fluid dynamics and heat transfer (10 papers); Heat transfer in nuclear plants (8 papers); Natural, forced and mixed convection (10 papers) and Conduction and radiation (4 papers). To encourage the debate, the Conference Program scheduled 16 oral sessions (44 papers), three ample poster sessions (36 papers) and four invited lectures given by experts in the various fields both from Industry and from University. Keynote Lectures were given by Dr. Roberto Parri (ENEL, Italy), Prof. Peter Stephan (TU Darmstadt, Germany), Prof. Bruno Panella (Politecnico di Torino), and Prof. Sara Rainieri (Universit;aacute; di Parma). This special volume collects a selection of the scientific contributions discussed during this conference. A total of 46 contributions, two keynote lectures and 44 papers both from oral and poster sessions, have been selected for publication in this special issue, after a second accurate revision process. These works give a good overview of the state of the art of Italian research in the field of Heat Transfer related topics at the date. The editors of the

Cooperative Control of Multiple Unmanned Autonomous Vehicles

Science.gov (United States)

2005-06-03

I I Final Report 4. TITLE AND SUBTITLE 5. FUNDING NUMBERS Cooperative Control of Multiple Unmanned Autonomous Vehicles F49620-01-1-0337 6. AUTHOR(S... Autonomous Vehicles Final Report Kendall E. Nygard Department of Computer Science and Operations Research North Dakota State University Fargo, ND 58105-5164

Nd(NH2SO3)(SO4) . 1.5 H2O: a non-centrosymmetric amidosulfate-sulfate of neodymium

International Nuclear Information System (INIS)

Wickleder, M.S.

2005-01-01

The thermal decomposition of Nd(NH 2 SO 3 ) 3 . 2 H 2 O in a closed tube leads to violet single crystals of Nd(NH 2 SO 3 )(SO 4 ) . 1.5 H 2 O. The compound crystallizes with the space group P1 (Z = 2, a = 689.2, b = 691.4, c = 962.0 pm, α = 109.64, β = 97.00, γ = 109.62 ). The triclinic unit cell can be transformed into the respective bodycentered setting I1 (Z = 2, a = 977.9, b = 795.6, c = 1113.0 pm, α = 90.69, β = 115.06, γ = 88.98 ) leading to a nearly monoclinic unit cell for the compound. In the crystal structure of Nd(NH 2 SO 3 )(SO 4 ) . 1.5 H 2 O two Nd 3+ ions are present. Nd(1) 3+ is coordinated by four NH 2 SO 3 - and two SO 4 2- ions, and one H 2 O molecule. Owing to the chelating attack of the sulfate groups, the CN is nine. Nd(2) 3+ is surrounded by four monodentate SO 4 2- and two NH 2 SO 3 - groups. Two H 2 O ligands fill up the coordination sphere and lead to a CN of eight. The linkage of the polyhedra leads to a three-dimensional network. (orig.)

Combination of CO2 and Q-switched Nd:YAG lasers is more effective than Q-switched Nd:YAG laser alone for eyebrow tattoo removal.

Science.gov (United States)

Radmanesh, Mohammad; Rafiei, Zohreh

2015-04-01

The eyebrow tattoo removal using Q-switched lasers is usually prolonged. Other modalities may be required to enhance the efficacy and shorten the treatment course. To compare the efficacy of Q-switched neodymium-doped yttrium aluminum garnet (Nd:YAG) laser alone versus combination of Q-switched Nd:YAG and Ultrapulse CO2 lasers for eyebrow tattoo removal after a single session. After local anesthesia, the right eyebrow of 20 patients was treated with Ultrapulse CO2 laser with the parameters of 4 J/cm(2) and 3.2 J/cm(2) for the first and the second passes. Both eyebrows were then treated with 1064-nm and 532-nm Q-switched Nd:YAG laser. The spot size and pulse duration were 3 mm and 5 nanoseconds for both wavelengths, and the fluence was 7 J/cm(2) for 1064 nm and 3 J/cm (2) for 532 nm. The side treated with combination of Q-switched Nd:YAG and CO2 lasers improved 75-100% in 6 of 20 patients versus only 1 of 20 in the side treated with Q-switched Nd:YAG alone. Similarly, the right side in 13 of 20 patients showed more than 50% improvement with combination therapy versus the left side (the monotherapy side), where only 6 of 20 cases showed more than 50% improvement. The Mann-Whitney test was 2.85 for the right side and 1.95 for the left side (P value = 0.007). Using Ultra pulse CO2 laser enhances the efficacy of Q-switched Nd:YAG laser in eyebrow tattoo removal.

Propagation of Nd magnetic phases in Nd/Sm(001) superlattices

International Nuclear Information System (INIS)

Soriano, S; Dufour, C; Dumesnil, K; Stunault, A

2006-01-01

The propagation of Nd long range magnetic order in the hexagonal and cubic sublattices has been investigated in double hexagonal compact Nd/Sm(001) superlattices by resonant x-ray magnetic scattering at the Nd L 2 absorption edge. For a superlattice with 3.7 nm thick Sm layers, the magnetic structure of the hexagonal sublattice propagates coherently through several bilayers, whereas the order in the cubic sublattice remains confined to single Nd blocks. For a superlattice with 1.4 nm thick Sm layers, the magnetic structures of both sublattices appear to propagate coherently through the superlattice. This is the first observation (i) of the long range coherent propagation of Nd order on the cubic sites between Nd blocks and (ii) of a different thickness dependence of the propagation of the Nd magnetic phases associated with the hexagonal and cubic sublattices. The propagation of the Nd magnetic order through Sm is interpreted in terms of generalized susceptibility of the Nd conduction electrons

Design and Control of a 3 kW Wireless Power Transfer System for Electric Vehicles

Directory of Open Access Journals (Sweden)

Zhenshi Wang

2015-12-01

Full Text Available This paper aims to study a 3 kW wireless power transfer system for electric vehicles. First, the LCL-LCL topology and LC-LC series topology are analyzed, and their transfer efficiencies under the same transfer power are compared. The LC-LC series topology is validated to be more efficient than the LCL-LCL topology and thus is more suitable for the system design. Then a novel q-Zsource-based online power regulation method which employs a unique impedance network (two pairs of inductors and capacitors to couple the cascaded H Bridge to the power source is proposed. By controlling the shoot-through state of the H Bridge, the charging current can be adjusted, and hence, transfer power. Finally, a prototype is implemented, which can transfer 3 kW wirelessly with ~95% efficiency over a 20 cm transfer distance.

Nd2Fe14C-based magnet with better permanent magnetic properties prepared by a simple mechanochemical method

Science.gov (United States)

Geng, Hongmin; Ji, Yuan; Zhang, Jingjing; Gao, Yuchao; Yan, Yu; Wang, Wenquan; Su, Feng; Du, Xiaobo

2017-11-01

Nd2Fe14C-based magnet is prepared by a mechanochemical method, namely high-energy ball-milling Nd2Fe11Bx (x = 0-0.15) alloy in heptane (C7H16), followed by annealing to 850 °C in vacuum. Under the action of high-energy ball-milling, Nd2Fe11Bx react with heptane to form NdH2+δ, Fe-(CB), C, etc. H2 is released and Nd2Fe17, Nd2Fe17Cx (x = 0-3), Nd2Fe14C, Nd carbides and α-Fe are formed in the subsequent annealing. C amount depends on ball-milling time t. Long time ball milling or high C content suppresses the formation of 2:17 phase and favors the formation of 2:14:1 phase in the final products. Excessive ball-milling results in the quick increase of α-Fe. The maximum of magnetically hard Nd2Fe14C is obtained at t = 4 h. For Nd2Fe11 samples, there exists considerable quantity of Nd carbides and α-Fe phase appears earlier and increases rapidly with extending the ball-milling time t. The addition of B element shortens the ball-milling time of the formation of maximum Nd2Fe14C and prominently suppresses the formation of Nd carbide and α-Fe. The optimum magnetic properties, coercivity iHc of 1193.7 kA/m, remanence Mr of 580.9 kA/m, maximum magnetic energy product (BH)max of 91.7 kJ/m3 is approaching to its theoretic value of 99.2 kJ/m3 for isotropic Nd2Fe14C magnet, are obtained in Nd2Fe11B0.06 alloy ball milled for 3.5 h.

Kinetics of selected elementary reactions of NH(a{sup 1}{delta}) or ND(a{sup {delta}}), NH(X{sup 3}{sigma}{sup -}) or ND(X{sup 3}{sigma}{sup -}) and NH{sub 2}(X), NHD(X), NH{sub 2}(X) radicals; Untersuchung der Kinetik ausgewaehlter Elementarreaktionen von NH(a{sup 1}{delta})- bzw. ND(a{sup 1}{delta})-, NH(X{sup 3}{sigma}{sup -})- bzw. ND(X{sup 3}{sigma}{sup -})- und NH{sub 2}(X)-, NHD(X)-, ND{sub 2}(X)-Radikalen

Energy Technology Data Exchange (ETDEWEB)

Adam, L.

2002-02-01

The elementary reactions of the NH and ND radicals in the ground state and the first excited state with H({sup 2}S) atoms and with molecules containing hydrogen and fluorine element bonds were investigated in the gaseous phase at a pressure of p = 7-80 bar. The elementary reactions of the NH{sub 2}, NHD and ND{sub 2} radicals in the ground state with hydrogen halides in the gaseous phase were investigated as well. [German] Die Elementarreaktionen des NH- bzw. ND-Radikals im Elektronengrundzustand und im ersten elektronisch angeregten Zustand mit H({sup 2}S)-Atomen und mit Molekuelen, die Wasserstoff- und Fluor-Elementbindungen besitzen, wurden in der Gasphase bei einem Druck von p = 7 - 80 mbar untersucht. Weiterhin wurden die Elementarreaktionen der NH{sub 2}-, NHD- bzw. ND{sub 2}-Radikale im Elektronengrundzustand mit Halogenwasserstoffen in der Gasphase untersucht. (orig.)

Persistent deNOx Ability of CaAl2O4:(Eu, Nd/TiO2-xNy Luminescent Photocatalyst

Directory of Open Access Journals (Sweden)

Li Huihui

2011-01-01

Full Text Available Abstract CaAl2O4:(Eu, Nd/TiO2-xNy composite luminescent photocatalyst was successfully synthesized by a simple planetary ball milling process. Improvement of photocatalytic deNOx ability of TiO2-xNy, together with the persistent photocatalytic activity for the decomposition of NO after turning off the light were realized, by coupling TiO2-xNy with long afterglow phosphor, CaAl2O4:(Eu, Nd. The novel persistent photocatalytic behavior was related to the overlap between the absorption wavelength of TiO2-xNy and the emission wavelength of the CaAl2O4:(Eu, Nd. It was found that CaAl2O4:(Eu, Nd/TiO2-xNy composites provided the luminescence to persist photocatalytic reaction for more than 3 h after turning off the light. Graphical Abstract CaAl2O4:(Eu, Nd/TiO2-xNy composite luminescent photocatalyst with persistent deNOx activity after turning off the light was successfully synthesized by a simple planetary ball milling process. The novel persistent photocatalytic behavior was related to the overlap between the absorption wavelength of TiO2-xNy and the emission wavelength of the CaAl2O4:(Eu, Nd. Additional file 1 Click here for file

2nd Tourism Postdisciplinarity Conference

DEFF Research Database (Denmark)

Following the noted success of the 1st international conference on postdisciplinary approaches to tourism studies (held in Neuchatel, Switzerland, 19-22 June, 2013), we are happy to welcome you to the 2nd Tourism Postdisciplinarity Conference. Postdisciplinarity surpasses the boundaries...... of study less embedded in that system of thought. Postdisciplinarity is an epistemological endeavour that speaks of knowledge production and the ways in which the world of physical and social phenomena can be known. It is also an ontological discourse as it concerns what we call ‘tourism...

The 2nd reactor core of the NS Otto Hahn

International Nuclear Information System (INIS)

Manthey, H.J.; Kracht, H.

1979-01-01

Details of the design of the 2nd reactor core are given, followed by a brief report summarising the operating experience gained with this 2nd core, as well as by an evaluation of measured data and statements concerning the usefulness of the knowledge gained for the development of future reactor cores. Quite a number of these data have been used to improve the concept and thus the specifications for the fuel elements of the 3rd core of the reactor of the NS Otto Hahn. (orig./HP) [de

Spectroscopy and enhanced frequency upconversion in Nd3+-Yb3+ codoped TPO glasses: energy transfer and NIR to visible upconverter

Science.gov (United States)

Azam, Mohd; Rai, Vineet Kumar; Mohanty, Deepak Kumar

2017-09-01

TeO2-Pb3O4 (TPO) glasses codoped with Nd3+ and Yb3+ ions have been fabricated by conventional melting technique. The absorption, emission and excitation spectra of the samples have been recorded. The optical band gap in both the doped/codoped glasses is found to be ˜3.31 eV. Judd-Ofelt analysis has been carried out by using the absorption spectrum of 0.8 mol% Nd3+ doped glass to determine the radiative properties viz radiative transition probabilities, branching ratios, radiative lifetimes, quality factor and emission cross sections of some emitting levels for Nd3+ ions. The radiative transition probability for the 4G7/2 → 4I9/2 transition (˜1926 Hz) is found to be maximum compared to other 4G5/2 → 4I9/2 (˜1622 Hz) and 4F5/2 → 4I9/2 (˜865 Hz) transitions. Upconversion (UC) luminescence of the samples has been examined by the 980 nm CW diode laser excitation. Effect of addition of Yb3+ ions in the Nd3+ doped glasses on UC emission intensity has been discussed. The UC emission intensity corresponding to the green, red and NIR bands in the codoped glass has been enhanced by ˜17, ˜12 and ˜42 times as compared to that of the Nd3+ singly doped glass. The quantum efficiency for the 4G7/2 level is found to be ˜32%. The nephelauxetic ratio, bonding parameter and covalency of Nd3+ ions have been found positive which represents the covalent bonding between Nd3+ ion and oxygen atom. The colour tunability from yellowish-green to dominant green region has been obtained in the optimized codoped TPO glass.

Study of magnetic field to promote oxygen transfer and its application in zinc–air fuel cells

International Nuclear Information System (INIS)

Shi, Jicheng; Xu, Hongfeng; Lu, Lu; Sun, Xin

2013-01-01

Highlights: ► High magnetic strength reduces R ct and increases C d in oxygen reduction reaction. ► Oxygen diffusion and transfer coefficient become large in high magnetic strength. ► The magnetic ZAFC discharge performance is better than the nonmagnetic ZAFC. ► Increased NdFeB/C load density improves the magnetic ZAFC discharge performance. ► Excess NdFeB/C load density decreases the magnetic ZAFC discharge performance. -- Abstract: This study investigates the effects of magnetic field on oxygen transfer and the correlations of electrochemical parameters in different magnetic strengths. The discharge performance of zinc–air fuel cell (ZAFC) was tested under magnetic and nonmagnetic conditions using neodymium–iron–boron/carbon (NdFeB/C) magnetic particles in ZAFC cathode. The results showed that the oxygen diffusion coefficient (D Oi ) and transfer coefficient (α i ) increased by 102.14% and 52.38% when the magnetic strength increased from 0 mT to 5.0 mT, respectively. In addition, the electric double-layer capacitance (C d ) increased from 8.16 to 22.46 μF cm −2 , the charge-transfer resistance (R ct ) decreased from 9.43 Ω cm 2 to 6.02 Ω cm 2 , and the oxygen reduction reaction (ORR) current was improved. With the NdFeB/C load density of 2.4 mg cm −2 in ZAFC cathode, the discharge current of magnetic ZAFC increased by 13.86% compared with the nonmagnetic ZAFC at the 0.80 V discharge voltage. These results indicate that magnetic strength has a positive correlation with D Oi , α i , and the ORR current. Under magnetic attractions, the oxygen transfer process is easier at the Pt/C catalytic surface, and the discharge performance of magnetic ZAFC is superior to the nonmagnetic ZAFC. At lower NdFeB/C load density, increasing the NdFeB/C load density facilitates oxygen transfer and improves the discharge performance of ZAFC. However, the magnetic ZAFC discharge performance decreases at a higher NdFeB/C load density because of the blocked oxygen

Luminescence properties of Nd3+-doped Y2O3 nanoparticles in organic media

International Nuclear Information System (INIS)

Cui, Xiaoxia; Hou, Chaoqi; Lu, Jiabao; Gao, Chao; Wei, Wei; Peng, Bo

2011-01-01

Nd 3+ -doped yttrium oxide nanoparticles (Y 2 O 3 :Nd) with cubic phase were obtained successfully by a glycine-nitrate solution combustion method. The results of Fourier transform infrared spectra (FTIR) showed that the -OH groups residing on the nanoparticles surfaces were reduced effectively by modifying with capping agent. The modified Y 2 O 3 :Nd nanoparticles displayed good monodispersity and excellent luminescence in N,N-dimethylformamide (DMF) solvent. Some optical parameters were calculated by Judd-Ofelt analysis based on absorption and fluorescence spectra. A relative large stimulated emission cross section, 1.7 x 10 -20 cm 2 , of the 4 F 3/2 → 4 I 11/2 transition was calculated. Theses results show that the modified Y 2 O 3 :Nd nanoparticles display good luminescence behavior in organic media. (orig.)

A route for recycling Nd from Nd-Fe-B magnets using Cu melts

Energy Technology Data Exchange (ETDEWEB)

Moore, Martina; Gebert, Annett, E-mail: a.gebert@ifw-dresden.de; Stoica, Mihai; Uhlemann, Margitta; Löser, Wolfgang

2015-10-25

Phase evolutions in Nd-Fe-B magnet/Cu systems have been explored with regard to Nd recycling. It was demonstrated that large scale phase separation into a ferromagnetic Fe(B)-rich ingot core with α-Fe main phase and a non-magnetic (Cu,Nd)-rich ingot rim takes place upon arc melting with Cu fractions ≥ 21.5 wt.-%. The re-solidification of the Nd{sub 2}Fe{sub 14}B magnet main phase is suppressed. The rim consists of the Cu{sub 2}Nd main phase and CuNd/Cu{sub 4}Nd minority phases in which Al traces from the magnetic material are gathered. Induction melting of such Nd-Fe-B/Cu mixtures can support the separation of these phase regions with very sharp boundaries. Main features of liquid phase separation and microstructure evolution have been interpreted on the basis of Nd-Fe-Cu phase diagram data. The key advantage with respect to Nd recycling from Nd-Fe-B permanent magnet scrap is the substantial accumulation of Nd in the (Cu,Nd)-rich region of the phase separated solidified specimen, which can be easily detached from the Fe-rich part by mechanical-magnetic treatments. Such portions contained up to ∼44 wt.-% Nd (25 at.-%) in first lab-scale experiments. Nd recovery from the (Cu,Nd)-rich fractions is possible by exploiting the large chemical property differences between the reactive rare earths elements and Cu. - Highlights: • phase evolution analysis in Nd-Fe-B magnet/Cu systems with regard to Nd recycling. • Cu ≥ 21 wt.-%, large scale phase separation- Fe(B)-rich ingot core, (Cu,Nd)-rich rim. • high Nd content (∼44 wt.-%) of (Cu,Nd)-rich region, mechanical-magnetic treatments.

Single NdPc{sub 2} molecules on surfaces. Adsorption, interaction, and molecular magnetism

Energy Technology Data Exchange (ETDEWEB)

Fahrendorf, Sarah

2013-01-24

They have huge potential for application in molecular-spin-transistors, molecular-spinvalves, and molecular quantum computing. SMMs are characterized by high spin ground states with zero-field splitting leading to high relaxation barriers and long relaxation times. A relevant class of molecules are the lanthanide double-decker phthalocyanines (LaPc{sub 2}) with only one metal atom sandwiched between two organic phthalocyanine (Pc) ligands. For envisaged spintronic applications it is important to understand the interaction between the molecules and the substrate and its influence on the electronic and magnetic properties. The subject of this thesis is the investigation of the adsorbed neodymium double-decker phthalocyanine (NdPc{sub 2}) by means of low temperature scanning tunneling microscopy and spectroscopy (STM and STS). The molecules are deposited by sublimation onto different substrates. It is observed that a large fraction of the double-decker molecules decomposes during deposition. The decomposition probability strongly depends on the chosen substrate. Therefore it is concluded that the substrate modifies the electronic structure of the molecule leading to a stabilization or destabilization of the molecular entity. Charge transfer from the surface to the molecule is identified as a potential stabilizing mechanism. The electronic and magnetic properties are investigated in detail for adsorbed NdPc{sub 2} molecules on Cu(100). The results of the experimental study are compared to state-of-the-art density functional theory calculations performed by our colleagues from the Peter Gruenberg Institute (PGI-1) at the Forschungszentrum Juelich. Interestingly, the lower Pc ring of the molecule hybridizes intensely with the substrate leading to strong chemisorption of the molecule, while the upper Pc ring keeps its molecular type electronic states, which can be energetically shifted by an external electric field. Importantly, it is possible to get direct access to the

Study on magnetic properties of (Nd0.8Ce0.2)2-xFe12Co2B (x = 0-0.6) alloys

Science.gov (United States)

Tan, G. S.; Xu, H.; Yu, L. Y.; Tan, X. H.; Zhang, Q.; Gu, Y.; Hou, X. L.

2017-09-01

In the present work, (Nd0.8Ce0.2)2-xFe12Co2B (x = 0-0.6) permanent alloys are prepared by melt-spinning method. The hard magnetic properties of (Nd0.8Ce0.2)2-xFe12Co2B (x = 0-0.6) alloys annealed at optimum temperatures have been investigated systematically. Depending on the Nd, Ce concentration, the maximum energy product ((BH)max) and remanence (Br) increase gradually with x in the range of 0 ≤ x ≤ 0.4, whereas decrease gradually in the alloys with 0.4 plays a certain role in the magnetization reversal behavior and can improve the microstructure of (Nd0.8Ce0.2)1.6Fe12Co2B alloy.

Frustrated ground state in the metallic Ising antiferromagnet Nd2Ni2In

Science.gov (United States)

Sala, G.; Mašková, S.; Stone, M. B.

2017-10-01

We used inelastic neutron scattering measurements to examine the intermetallic Ising antiferromagnet Nd2Ni2In . The dynamical structure factor displays a spectrum with multiple crystal field excitations. These crystal field excitations consist of a set of four transitions covering a range of energies between 4 and 80 meV. The spectrum is very sensitive to the temperature, and we observed a softening and a shift in the energies above the transition temperature of the system. The analysis of the crystalline electric field scheme confirms the Ising nature of the spins and their orientation as proposed by previous studies. We characterized Nd2Ni2In as a large moment intermetallic antiferromagnet with the potential to support a geometrically frustrated Shastry-Sutherland lattice.

Effects of Al substitution in Nd2Fe17 studied by first-principles calculations

International Nuclear Information System (INIS)

Huang, M.; Ching, W.Y.

1994-01-01

We have studied the effect of Al substitution in Nd 2 Fe 17 compound by means of first-principles calculations. We first obtain the site-decomposed potentials for Fe from self-consistent calculation on Y 2 Fe 17 and the atomiclike potentials in the crystalline environment for Al and Nd. Calculations are carried out for a single Al substituting one Fe at four different Fe sites (6c), (9d), (18f ), and (18h), two Al substituting two Fe (18h), and four Al substituting three Fe (18h) and one Fe (18f ). Our results show that the Al moment is oppositely polarized to Fe. The average moment per Fe atom actually increases for Al substituting Fe (18h) and Fe (18f ) is about the same for Al substituting Fe (6c), and is drastically reduced when replacing Fe (9d). Experimentally, Al is shown to be excluded from the (9d) sites because of the small Wigner--Seitz volume. When two Fe atoms are replaced by two Al atoms, the total moment is only slightly less than when only one Fe atom is replaced, and the M s per Fe site actually increases, in agreement with the Moessbauer data. These results are analyzed in terms of the local atomic geometry and the charge transfer effect from the neighboring Fe to Al

Phase relations in the ZrO2-Nd2O3-Y2O3 system. Experimental study and CALPHAD assessment

International Nuclear Information System (INIS)

Fabrichnaya, Olga; Savinykh, Galina; Schreiber, Gerhard; Seifert, Hans J.

2010-01-01

The thermodynamic parameters of the Nd 2 O 3 Y 2 O 3 system were re-assessed for better reproduction of experimental data. The thermodynamic parameters were combined from binary descriptions to calculate phase diagrams for the ternary system ZrO 2 -Nd 2 O 3 Y 2 O 3 . The calculated phase diagrams were used to select compositions for the experimental studies at 1250, 1400 and 1600 C. The samples were synthesised by co-precipitation and heat treated at 1250-1600 C, investigated by X-ray diffraction and scanning electron microscopy combined with energy dispersive X-ray spectroscopy. It was found that solubility of the Y 2 O 3 in the pyrochlore phase exceeds 10 mol.%. The experimental data obtained for phase equilibria were used to derive thermodynamic parameters for fluorite, Y 2 O 3 cubic phase C, monoclinic B and Nd 2 O 3 hexagonal A phases by CALPHAD method. The isothermal sections and liquidus surface were calculated for the ZrO 2 -Nd 2 O 3 Y 2 O 3 system. (orig.)

2nd International Arctic Ungulate Conference

OpenAIRE

Anonymous, A.

1996-01-01

The 2nd International Arctic Ungulate Conference was held 13-17 August 1995 on the University of Alaska Fairbanks campus. The Institute of Arctic Biology and the Alaska Cooperative Fish and Wildlife Research Unit were responsible for organizing the conference with assistance from biologists with state and federal agencies and commercial organizations. David R. Klein was chair of the conference organizing committee. Over 200 people attended the conference, coming from 10 different countries. T...

H-II Transfer Vehicle (HTV) and the Operations Concept for Extravehicular Activity (EVA) Hardware

Science.gov (United States)

Chullen, Cinda; Blome, Elizabeth; Tetsuya, Sakashita

2011-01-01

With the retirement of the Space Shuttle fleet imminent in 2011, a new operations concept will become reality to meet the transportation challenges of the International Space Station (ISS). The planning associated with the retirement of the Space Shuttle has been underway since the announcement in 2004. Since then, several companies and government entities have had to look for innovative low-cost commercial orbital transportation systems to continue to achieve the objectives of ISS delivery requirements. Several options have been assessed and appear ready to meet the large and demanding delivery requirements of the ISS. Options that have been identified that can facilitate the challenge include the Russian Federal Space Agency's Soyuz and Progress spacecraft, European Space Agency's Automated Transfer Vehicle (ATV), and the Japan Aerospace Exploration Agency's (JAXA s) H-II Transfer Vehicle (HTV). The newest of these options is the JAXA's HTV. This paper focuses on the HTV, mission architecture and operations concept for Extra-Vehicular Activities (EVA) hardware, the associated launch system, and details of the launch operations approach.

From 1st- to 2nd-Generation Biofuel Technologies: Extended Executive Summary

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

This report looks at the technical challenges facing 2nd-generation biofuels, evaluates their costs and examines related current policies to support their development and deployment. The potential for production of more advanced biofuels is also discussed. Although significant progress continues to be made to overcome the technical and economic challenges, 2nd-generation biofuels still face major constraints to their commercial deployment.

Superconductivity in Pd-Intercalated Ternary Rare-Earth Polychalcogenide NdSeTe_2

International Nuclear Information System (INIS)

Wang Pei-Pei; Xue Mian-Qi; Long Yu-Jia; Zhao Ling-Xiao; Cai Yao; Yang Huai-Xin; Li Jian-Qi; Ren Zhi-An; Chen Gen-Fu

2015-01-01

We synthesize a set of Pd-doped polycrystalline samples Pd_xNdSeTe_2 and measure their physical properties. Compared with pure NdSeTe_2, the charge density wave (CDW) order is continuously suppressed with the Pd-intercalation. Bulk superconductivity first appears at x = 0.06 with T_c nearly 2.5K, coexisting with a CDW transition at 176K. Further Pd-doping enhances T_c, until it reaches the maximum value 2.84K at x=0.1, meanwhile the CDW transition vanishes. The upper critical field for the optimal doping sample Pd_0_._1NdSeTe_2 is determined from the R-H measurement, which is estimated to be 0.6 T. These results provide another kind of ideal compound for studying the interplay between CDW and superconductivity systematically. (paper)

Fire simulation of the canister transfer and installation vehicle; Kapselin siirto- ja asennusajoneuvon palosimulointi

Energy Technology Data Exchange (ETDEWEB)

Peltokorpi, L. [Fortum Power and Heat Oy, Espoo (Finland)

2012-12-15

A pyrolysis model of the canister transfer and installation vehicle was developed and vehicle fires in the final disposal tunnel and in the central tunnel were simulated using the fire simulation program FDS (Fire Dynamics Simulator). For comparison, same vehicle fire was also simulated at conditions in which the fire remained as a fuel controlled during the whole simulation. The purpose of the fire simulations was to simulate the fire behaviour realistically taking into account for example the limitations coming from the lack of oxygen. The material parameters for the rubber were defined and the simulation models for the tyres developed by simulating the fire test of a front wheel loader rubber tyre done by SP Technical Research Institute of Sweden. In these simulations the most important phenomena were successfully brought out but the timing of the phenomena was difficult. The final values for the rubber material parameters were chosen so that the simulated fire behaviour was at least as intense as the measured one. In the vehicle fire simulations a hydraulic oil or diesel leak causing a pool fire size of 2 MW and 2 m{sup 2} was assumed. The pool fire was assumed to be located under the tyres of the SPMT (Self Propelled Modular Transporters) transporter. In each of the vehicle fire simulations only the tyres of the SPMT transporter were observed to be burning whereas the tyres of the trailer remained untouched. In the fuel controlled fire the maximum power was slightly under 10 MW which was reached in about 18 minutes. In the final disposal tunnel the growth of the fire was limited due to the lack of oxygen and the relatively fast air flows existing in the tunnel. Fast air flows caused the flame spreading to be limited to the certain directions. In the final disposal tunnel fire the maximum power was slightly over 7 MW which was reached about 8 minutes after the ignition. In the central tunnel there was no shortage of oxygen but the spread of the fire was limited

Study of Nd-Fe-B alloys with nonstoichiometric Nd content in optimal magnetic state

Directory of Open Access Journals (Sweden)

Ćosović V.

2009-01-01

Full Text Available Characterization of two rapid-quenched Nd-Fe-B alloys with nonstoichiometric Nd content in the optimized magnetic state was carried out using the X-ray diffractometry (XRD, 57Fe Mössbauer spectroscopic phase analysis (MS, electron microscopy (TEM, high resolution TEM (HREM and Superconducting Quantum Interference Device (SQUID magnetometer. The experimental results demonstrate the fundamental difference in the structure and magnetic properties of the two investigated alloys in the optimized magnetic state. The Nd-Fe-B alloy with the reduced Nd content (Nd4.5Fe77B18.5 was found to have the nanocomposite structure of Fe3B/Nd2Fe14B and partly α-Fe/Nd2Fe14B, with mean grain size below 30 nm. On the other side, the overstoichiometric Nd14Fe79B7 alloy has almost a monophase structure with the dominant content of the hard magnetic phase Nd2Fe14B (up to 95 wt. % and a mean crystallite size about 60 nm, as determined by XRD and TEM analysis. The results of magnetic measurements on SQUID magnetometer also suggest the nanocomposite structure of the Nd-low alloy and nanocrystalline decoupled structure of the Nd-rich alloy after the optimal heat treatment.

Upconversion in Nd3+-doped glasses: Microscopic theory and spectroscopic measurements

International Nuclear Information System (INIS)

Oliveira, S. L.; Sousa, D. F. de; Andrade, A. A.; Nunes, L. A. O.; Catunda, T.

2008-01-01

In this work, we report a systematic investigation of upconversion losses and their effects on fluorescence quantum efficiency and fractional thermal loading in Nd 3+ -doped fluoride glasses. The energy transfer upconversion (γ up ) parameter, which describes upconversion losses, was experimentally determined using different methods: thermal lens (TL) technique and steady state luminescence (SSL) measurements. Additionally, the upconversion parameter was also obtained from energy transfer models and excited state absorption measurements. The results reveal that the microscopic treatment provided by the energy transfer models is similar to the macroscopic ones achieved from the TL and SSL measurements because similar γ up parameters were obtained. Besides, the achieved results also point out the migration-assisted energy transfer according to diffusion-limited regime rather than hopping regime as responsible for the upconversion losses in Nd-doped glasses

Polarized spectroscopic properties of Nd3+-doped KGd(WO4)2 single crystal

International Nuclear Information System (INIS)

Chen Yujin; Lin Yanfu; Gong Xinghong; Tan Qiguang; Zhuang Jian; Luo Zundu; Huang Yidong

2007-01-01

The polarized absorption spectra, infrared fluorescence spectra, upconversion visible fluorescence spectra, and fluorescence decay curve of orientated Nd 3+ :KGd(WO 4 ) 2 crystal were measured at room-temperature. Some important spectroscopic parameters were investigated in detail in the framework of the Judd-Ofelt theory and the Fuchtbauer-Ladenburg formula. The effect of the crystal structure on the spectroscopic properties of the Nd 3+ ions was analyzed. The relation among the spectroscopic parameters and the laser performances of the Nd 3+ :KGd(WO 4 ) 2 crystal was discussed

STABILITY CONTROL OF ELEVATING-TRANSFER VEHICLES IN THE CONSTRUCTION

Directory of Open Access Journals (Sweden)

Zhadanovskiy Boris Vasil’evich

2016-05-01

Full Text Available The underground space is widely used in the construction in big cities of the Russian Federation. These works need the use of elevating-transfer vehicles. In this case the requirements of norms and regulations on operating safety should be strictly observed, because their breach often leads to emergency situations and injuries. The organizational and technological solutions when developing the design documentation and executing construction and assembly works should be primarily based on the stability of lifting facilities. The author states the requirements to installation of lifting tackles (cranes. The features of their installation in different operation conditions on construction sites are described. The crane stability depends on many different indicators, which are considered by the author. The calculation algorithms of crane stability are offered.

Structural and magnetic transformations in NdMn2Hx hydrides

International Nuclear Information System (INIS)

Budziak, A.; Zachariasz, P.; Pełka, R.; Figiel, H.; Żukrowski, J.; Woch, M.W.

2012-01-01

Highlights: ► Full structural phase diagram is presented for the NdMn 2 H x (2.0 ≤ x ≤ 4.0) hydrides in the temperature range of 70–385 K. ► For samples x = 2.0, 2.5, and 4.0 a splitting into two phases with different hydrogen concentrations are observed. ► Only for samples with x = 3.0 and 3.5 no spinodal decompositions are detected. ► The effects of hydrogen absorption on structural properties are shown to be reflected in magnetic behavior. ► A huge jump of magnetic ordering temperatures from ∼104 K for host NdMn 2 to above 200 K for its hydrides is observed or anticipated. - Abstract: X-ray powder diffraction and bulk magnetization measurements were used to study structural and magnetic properties of hydrides NdMn 2 H x (2.0 ≤ x ≤ 4.0). The X-ray investigations performed in the temperature range 70–385 K have revealed many structural transformations at low temperatures. In particular, a transformation from the hexagonal to the monoclinic phase and spinodal decompositions were observed. The magnetic behavior of the hydrides is correlated with the structural transitions. A tentative structural diagram is presented. The obtained results are compared with the properties of other cubic and hexagonal RMn 2 H x hydrides.

REE Recovery from End-of-Life NdFeB Permanent Magnet Scrap : A Critical Review

NARCIS (Netherlands)

Yang, Y.; Walton, A; Sheridan, R.; Güth, K.; Gauß, R.; Gutfleisch, O; Buchert, M; Steenari, B-M,; Van Gerven, T; Jones, PT; Binnemans, K

2017-01-01

NdFeB permanent magnets have different life cycles, depending on the applications: from as short as 2–3 years in consumer electronics to 20–30 years in wind turbines. The size of the magnets ranges from less than 1 g in small consumer electronics to about 1 kg in electric vehicles (EVs) and hybrid

In-situ electric field in human body model in different postures for wireless power transfer system in an electrical vehicle

International Nuclear Information System (INIS)

Shimamoto, Takuya; Laakso, Ilkka; Hirata, Akimasa

2015-01-01

The in-situ electric field of an adult male model in different postures is evaluated for exposure to the magnetic field leaked from a wireless power transfer system in an electrical vehicle. The transfer system is located below the centre of the vehicle body and the transferred power and frequency are 7 kW and 85 kHz, respectively. The in-situ electric field is evaluated for a human model (i) crouching near the vehicle, (ii) lying on the ground with or without his arm stretched, (iii) sitting in the driver’s seat, and (iv) standing on a transmitting coil without a receiving coil. In each scenario, the maximum in-situ electric fields are lower than the allowable limit prescribed by international guidelines, although the local magnetic field strength in regions of the human body is higher than the allowable external magnetic field strength. The highest in-situ electric field is observed when the human body model is placed on the ground with his arm extended toward the coils, because of a higher magnetic field around the arm. (paper)

In-situ electric field in human body model in different postures for wireless power transfer system in an electrical vehicle.

Science.gov (United States)

Shimamoto, Takuya; Laakso, Ilkka; Hirata, Akimasa

2015-01-07

The in-situ electric field of an adult male model in different postures is evaluated for exposure to the magnetic field leaked from a wireless power transfer system in an electrical vehicle. The transfer system is located below the centre of the vehicle body and the transferred power and frequency are 7 kW and 85 kHz, respectively. The in-situ electric field is evaluated for a human model (i) crouching near the vehicle, (ii) lying on the ground with or without his arm stretched, (iii) sitting in the driver's seat, and (iv) standing on a transmitting coil without a receiving coil. In each scenario, the maximum in-situ electric fields are lower than the allowable limit prescribed by international guidelines, although the local magnetic field strength in regions of the human body is higher than the allowable external magnetic field strength. The highest in-situ electric field is observed when the human body model is placed on the ground with his arm extended toward the coils, because of a higher magnetic field around the arm.

Nd Fe10 Mo2 alloys production through reduction-diffusion for nitrogenation

International Nuclear Information System (INIS)

Guilherme, Eneida da G.; Rechenberg, Hercilio R.

1996-01-01

In this work we have examined the effect of various processing variables on the Nd Fe 10 Mo 2 phase formation by reduction-diffusion calciothermic process (R D C). The best results were obtained for 4 hours treatment at 950 deg C with 40% excess content Nd Cl 3 and 50% excess content of Ca, for alloy Nd Fe 10.5 Mo 1.5 . Preliminary nitrogen absorption experiments have been done, without any further powder size reduction at temperatures between 300 and 350 deg C. (author)

Nd composition dependence of microstructure and magnetic properties for gradient sputtered NdFeB films

International Nuclear Information System (INIS)

Li Shandong; Wang Dawei; Fang Jianglin; Duh, J.-G.; Wang Yinying; Wu Yizhi; Huang Junheng; Zheng Hongjun

2008-01-01

NdFeB films with Nd compositions varied from 13.34 to 24.30 at% were deposited by DC gradient sputtering using targets Nd 12.5 Fe 71.5 B 16 and Nd. The hard magnetic properties, grain growth direction and magnetic domain structures were dramatically influenced by Nd composition. The samples with intermediate Nd concentrations exhibited optimal magnetic properties and microstructures, such as large squareness ratio over 0.9, large energy product up to 174 kJ/m 3 , and vertical domain structure. However, the samples with higher and lower Nd compositions showed almost isotropic loops. (0 0 l) as main X-ray diffraction peaks in the optimal Nd composition region indicated most of Nd 2 Fe 14 B grains with c-axis perpendicular to the film plane, while NdFeB grains in other region are almost random growth. The good magnetic properties can be attributed to the vertical growth of Nd 2 Fe 14 B grains

Nd composition dependence of microstructure and magnetic properties for gradient sputtered NdFeB films

Energy Technology Data Exchange (ETDEWEB)

Li Shandong [Department of Physics, Fujian Normal University, Fuzhou 350007 (China)], E-mail: dylsd007@yahoo.com.cn; Wang Dawei [Department of Physics, Fujian Normal University, Fuzhou 350007 (China); Fang Jianglin [Center for Materials Analysis, Nanjing University, Nanjing 210093 (China); Duh, J.-G. [Department of Materials Science and Engineering, National TsingHua Universtiy, Hsinchu, Taiwan (China); Wang Yinying; Wu Yizhi; Huang Junheng; Zheng Hongjun [Department of Physics, Fujian Normal University, Fuzhou 350007 (China)

2008-08-15

NdFeB films with Nd compositions varied from 13.34 to 24.30 at% were deposited by DC gradient sputtering using targets Nd{sub 12.5}Fe{sub 71.5}B{sub 16} and Nd. The hard magnetic properties, grain growth direction and magnetic domain structures were dramatically influenced by Nd composition. The samples with intermediate Nd concentrations exhibited optimal magnetic properties and microstructures, such as large squareness ratio over 0.9, large energy product up to 174 kJ/m{sup 3}, and vertical domain structure. However, the samples with higher and lower Nd compositions showed almost isotropic loops. (0 0 l) as main X-ray diffraction peaks in the optimal Nd composition region indicated most of Nd{sub 2}Fe{sub 14}B grains with c-axis perpendicular to the film plane, while NdFeB grains in other region are almost random growth. The good magnetic properties can be attributed to the vertical growth of Nd{sub 2}Fe{sub 14}B grains.

High-Temperature Heat Capacity of Germanates Pr2Ge2O7 and Nd2Ge2O7 within 350-1000 K

Science.gov (United States)

Denisova, L. T.; Irtyugo, L. A.; Beletskii, V. V.; Belousova, N. V.; Denisov, V. M.

2018-03-01

Pr2Ge2O7 and Nd2Ge2O7 were obtained via solid-phase synthesis from Pr2O3 ( Nd2O3) and GeO2 with multistage firing in air within 1273-1473 K. A temperature effect on molar heat capacity of the oxide compounds was measured with a differential scanning calorimetry. Their thermodynamic properties were calculated from the C P = f( T) dependences.

Colossal magnetoresistance in layered manganite Nd2−2xSr1+ ...

Indian Academy of Sciences (India)

starting compounds, have been obtained. Except for x=0.4, which is found to be an antiferromagnetic insulator, all other x values yielded metal–insulator transition and ferromagnetic ordering. Keywords. Colossal magnetoresistance; layered manganites; Nd2−2x Sr1+2x Mn2O7. PACS Nos 75.30.Vn; 71.30.+h. 1. Introduction.

Analysis of asthenic phenomens in patients with type 2nd diabetes mellitus in the clinical and psychological aspect

Directory of Open Access Journals (Sweden)

O. V. Tkachenko

2017-03-01

Full Text Available Aim – to analyze the peculiarities of asthenic manifestations in patients with type 2nd diabetes mellitus (DM in clinical and psychological perspective. Materials and methods. We examined in 543 patients with type 2nd DM. The first clinical group (CG-1 was 57 patients with type 2nd DM of mild severity; the average age in the group was (51,80±1,28 years. The second clinical group (CG-2 made up of 312 patients with type 2nd DM, moderate severity; mean age in the group was (55,10±1,12 years. The third clinical group (CG-3 included 174 patients with type 2nd DM, severe degree of severity; the average age in the group was (61.80±0,85 years. Research methods: clinical-anamnestic, clinical-psychopathological, statistical. Results. The marked prevalence of asthenic syndrome in patients wath type 2nd DM 52,30%, which is almost half among all surveyed type 2nd DM. Discovered the direct correlation of asthenic symptoms with the severity of the type 2nd DM (rs = 0.4033, p<0.01. The factors in the risk of asthenic syndrome in patients with type 2nd DM was installed, among them is dominated by a moderate and severe degree of type 2nd DM, combined with obesity 2 degrees, DEP II degree, ischemic heart disease, heart failure, degenerative dystrophic lesions of the spine. Established that there is a direct correlation asthenic syndrome to the severity of type 2nd DM, as well as the accompanying somatic pathology. Established dominance in CG-1 and CG-2 component fatigue "mental fatigue" and CG-3 component "physical fatigue". Conclusions. Features of asthenic manifestations in patients with type 2nd DM in clinical and psychological perspective were investigated. The detection rate of asthenic manifestations among patients with type 2nd DM and the factors for their amplification were established. The organic etiology of asthenic manifestations have been proven; presentation about the stages of development of asthenic symptoms in patients with type 2nd DM were

Low-voltage organic thin film transistors (OTFTs) using crosslinked polyvinyl alcohol (PVA)/neodymium oxide (Nd2O3) bilayer gate dielectrics

Science.gov (United States)

Khound, Sagarika; Sarma, Ranjit

2018-01-01

We have reported here on the design, processing and dielectric properties of pentacene-based organic thin film transitors (OTFTs) with a bilayer gate dilectrics of crosslinked PVA/Nd2O3 which enables low-voltage organic thin film operations. The dielectric characteristics of PVA/Nd2O3 bilayer films are studied by capacitance-voltage ( C- V) and current-voltage ( I- V) curves in the metal-insulator-metal (MIM) structure. We have analysed the output electrical responses and transfer characteristics of the OTFT devices to determine their performance of OTFT parameters. The mobility of 0.94 cm2/Vs, the threshold voltage of - 2.8 V, the current on-off ratio of 6.2 × 105, the subthreshold slope of 0.61 V/decade are evaluated. Low leakage current of the device is observed from current density-electric field ( J- E) curve. The structure and the morphology of the device are studied using X-ray diffraction (XRD) and atomic force microscope (AFM), respectively. The study demonstrates an effective way to realize low-voltage, high-performance OTFTs at low cost.

Effect of spin reorientation on magnetocaloric and transport properties of NdAl{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Souza, M.V. de, E-mail: marcos_vinicios@hotmail.com [Núcleo de Pós-Graduação em Física, Campus Prof. José Aloísio de Campos, UFS, 49100-000 São Cristóvão, SE (Brazil); Silva, J.A. da [Núcleo de Pós-Graduação em Física, Campus Prof. José Aloísio de Campos, UFS, 49100-000 São Cristóvão, SE (Brazil); Silva, L.S. [Núcleo de Pós-Graduação em Física, Campus Prof. José Aloísio de Campos, UFS, 49100-000 São Cristóvão, SE (Brazil); Instituto Federal de Tocantins, IFTO – Campus Colinas do Tocantins, AV. Bernardo Sayao S/N, Chácara Raio de Sol, Setor Santa Maria, CEP 77760-000 Colinas do Tocantins, TO (Brazil)

2017-01-01

We report the magneto-thermal and resistive properties of rare-earth dialuminide NdAl{sub 2}, including spin reorientation transition. To this purpose, we used a theoretical model that considers the interactions of exchange and Zeeman, besides the anisotropy due to the electrical crystal field. The theoretical results obtained were compared to experimental data of the NdAl{sub 2} in single crystal and bulk forms. Explicitly, we have calculated the anisotropic variation of magnetic entropy with the magnetic field oriented along the three principal crystallographic directions: [100], [110], and [111] of NdAl{sub 2} single crystal, where a signature of the spin reorientation is observed in the [110] and [111] directions. Moreover, of magnetoresistivity we consider the applied magnetic field along the crystallographic directions [100] and [110]. In turn, for the polycrystalline form, the good agreement between theory and experiment confirms the presence of spin reorientation, which was predicted theoretically in magnetization curves. - Highlights: • Modeling of the thermodynamics quantities in NdAl{sub 2} single crystal and policrystal. • Modeling of the transport properties in NdAl{sub 2} single crystal. • Effect of reorientation of spin on caloric and transport properties.

Luminescence properties of Yb:Nd:Tm:KY{sub 3}F{sub 10} nanophosphor and thermal treatment effects

Energy Technology Data Exchange (ETDEWEB)

Gomes, Laércio, E-mail: lgomes@ipen.br [Centro de Lasers e Aplicações, Instituto de Pesquisas Energéticas e Nucleares, IPEN-CNEN/SP, Butantã, P.O. Box 11049, São Paulo, SP o5422-970 (Brazil); Linhares, Horácio Marconi da Silva M.D. [Centro de Lasers e Aplicações, Instituto de Pesquisas Energéticas e Nucleares, IPEN-CNEN/SP, Butantã, P.O. Box 11049, São Paulo, SP o5422-970 (Brazil); Ichikawa, Rodrigo Uchida; Martinez, Luis Gallego [Departamento de Ciências dos Materiais, Instituto de Pesquisas Energéticas e Nucleares (Brazil); Ranieri, Izilda Marcia [Centro de Lasers e Aplicações, Instituto de Pesquisas Energéticas e Nucleares, IPEN-CNEN/SP, Butantã, P.O. Box 11049, São Paulo, SP o5422-970 (Brazil)

2015-01-15

In this work, we present the spectroscopic properties of KY{sub 3}F{sub 10} (KY3F) nanocrystals activated with thulium and codoped with ytterbium and neodymium ions. The most important processes that lead to the thulium upconversion emissions in the blue region were identified. A time-resolved luminescence spectroscopy technique was employed to measure the luminescence decays and to determine the most important mechanisms involved in the upconversion process that populates {sup 1}G{sub 4} (Tm{sup 3+}) excited states. Analysis of the energy-transfer processes dynamics using selective pulsed-laser excitations in Yb:Nd:Tm, Nd:KY3F nanocrystals shows that the direct energy transfer from Nd{sup 3+} to Tm{sup 3+} ions is the mechanism responsible for the 78% of the blue upconversion luminescence in the Yb:Nd:Tm:KY3F when compared with the Yb:Nd:Tm:KY3F bulk crystal for an laser excitation at 802 nm. An investigation of the {sup 1}G{sub 4} level luminescence kinetic of Tm{sup 3+} in Yb/Nd/Tm system revealed that the luminescence efficiency ({sup 1}G{sub 4}) starts with a very low value (0.38%) for the synthesized nanocrystal (as grown) and strongly increases to 97% after thermal treatment at 550 °C for 6 h under argon flow. As a consequence of the thermal treatment at T=550 °C, the contributions of the (Nd×Tm) (Up{sub 1}) and (Nd×Yb×Tm) (Up{sub 2}) upconversion processes to the {sup 1}G{sub 4} luminescence are 33% (Up{sub 1}) and 67% for Up{sub 2}. Up{sub 2} process represented by Nd{sup 3+} ({sup 4}F{sub 3/2})→Yb{sup 3+} ({sup 2}F{sub 7/2}) followed by Yb{sup 3+} ({sup 2}F{sub 5/2})→Tm ({sup 3}H{sub 4})→Tm{sup 3+} ({sup 1}G{sub 4}) was previously reported as the main mechanism to produce the blue luminescence in Yb:Nd:Tm:YLiF{sub 4} and KY{sub 3}F{sub 10} bulk crystals. Results of X-ray diffraction analysis of nanopowder using the Rietveld method reveled that crystallite sizes remain unchanged (12–14 nm) after thermal treatments with T≤400 °C, while the

Cost-Effectiveness Comparison of Coupler Designs of Wireless Power Transfer for Electric Vehicle Dynamic Charging

Directory of Open Access Journals (Sweden)

Weitong Chen

2016-11-01

Full Text Available This paper presents a cost-effectiveness comparison of coupler designs for wireless power transfer (WPT, meant for electric vehicle (EV dynamic charging. The design comparison of three common types of couplers is first based on the raw material cost, output power, transfer efficiency, tolerance of horizontal offset, and flux density. Then, the optimal cost-effectiveness combination is selected for EV dynamic charging. The corresponding performances of the proposed charging system are compared and analyzed by both simulation and experimentation. The results verify the validity of the proposed dynamic charging system for EVs.

Study on microstructure and properties of extruded Mg-2Nd-0.2Zn alloy as potential biodegradable implant material.

Science.gov (United States)

Li, Junlei; Tan, Lili; Wan, Peng; Yu, Xiaoming; Yang, Ke

2015-04-01

Mg-2Nd-0.2Zn (NZ20) alloy was prepared for the application as biodegradable implant material in this study. The effects of the extrusion process on microstructure, mechanical and corrosion properties of the alloy were investigated. The as-cast alloy was composed of α-Mg matrix and Mg12Nd eutectic compound. The solution treatment could lead to the Mg12Nd phase dissolution and the grain coarsening. The alloy (E1) preheated at 380°C for 1h and extruded at 390°C presents fine grains with amounts of tiny Mg12Nd particles uniformly dispersed throughout the boundaries and the interior of the grains. The alloy (E2) preheated at 480°C for 1h and extruded at 500°C exhibits relatively larger grains with few nano-scale Mg12Nd phase particles dispersed. The alloy of E1, compared with E2, showed relatively lower corrosion rate, higher yield strength and slightly lower elongation. Copyright © 2015 Elsevier B.V. All rights reserved.

Magnetic Properties of NdAl2

DEFF Research Database (Denmark)

Bak, P.

1974-01-01

The magnetic properties of NdAl2 are calculated using a Hamiltonian including crystal-field and isotropic exchange interaction terms. A two-dimensional mean-field theory is evaluated to calculate single-crystal magnetization curves. It is shown that the magnetic properties can be understood using...... the crystal-field parameters derived from the magnetic exciton spectrum measured by Houmann et al. by means of inelastic neutron scattering. The combined lambda -Schottky anomaly in the heat capacity is explained. No additional parameters are introduced....

High field magnetization process of (Sm, Nd)2Fe17Ny compounds

International Nuclear Information System (INIS)

Yu, M.J.; Tang, N.; Liu, Y.L.; Tegus, O.; Lu, Y.; Kuang, J.P.; Yang, F.M.; Li, X.; Zhou, G.F.; Boer, F.R. de

1992-01-01

The crystal structure and high-field magnetization process of (Sm 1-x Nd x ) 2 Fe 17 N y compounds (x = 0.0, 0.1, ..., 1.0, 2 1-x Nd x ) 2 Fe 17 N y compounds were found to crystallize in the rhombohedral Th 2 Zn 17 structure. As x increases, the Curie temperature decreases. The anisotropy fields and easy magnetization direction were investigated from 1.5 K to room temperature by means of high-field magnetization measurements and AC-susceptibility measurements, combined with X-ray diffraction on random and magnetically aligned powder samples. The anisotropy field decreases with increasing x and approaches a minimum value at about x = 0.6, then increases again. A tentative spin phase diagram for the (Sm 1-x Nd x ) 2 Fe 17 N y series is presented. At room temperature, the easy magnetization direction remains along the c-axis up to x = 0.6. (orig.)

All-optical 1st- and 2nd-order differential equation solvers with large tuning ranges using Fabry-Pérot semiconductor optical amplifiers.

Science.gov (United States)

Chen, Kaisheng; Hou, Jie; Huang, Zhuyang; Cao, Tong; Zhang, Jihua; Yu, Yuan; Zhang, Xinliang

2015-02-09

We experimentally demonstrate an all-optical temporal computation scheme for solving 1st- and 2nd-order linear ordinary differential equations (ODEs) with tunable constant coefficients by using Fabry-Pérot semiconductor optical amplifiers (FP-SOAs). By changing the injection currents of FP-SOAs, the constant coefficients of the differential equations are practically tuned. A quite large constant coefficient tunable range from 0.0026/ps to 0.085/ps is achieved for the 1st-order differential equation. Moreover, the constant coefficient p of the 2nd-order ODE solver can be continuously tuned from 0.0216/ps to 0.158/ps, correspondingly with the constant coefficient q varying from 0.0000494/ps(2) to 0.006205/ps(2). Additionally, a theoretical model that combining the carrier density rate equation of the semiconductor optical amplifier (SOA) with the transfer function of the Fabry-Pérot (FP) cavity is exploited to analyze the solving processes. For both 1st- and 2nd-order solvers, excellent agreements between the numerical simulations and the experimental results are obtained. The FP-SOAs based all-optical differential-equation solvers can be easily integrated with other optical components based on InP/InGaAsP materials, such as laser, modulator, photodetector and waveguide, which can motivate the realization of the complicated optical computing on a single integrated chip.

Magnetic properties of Nd-deficient manganites Nd0.9-xCaxMnOy

International Nuclear Information System (INIS)

Troyanchuk, I.O.; Khomchenko, V.A.; Pastushonok, S.N.; Novitsky, O.A.; Pavlov, V.I.; Szymczak, H.

2006-01-01

X-ray diffraction and magnetic studies of neodymium deficient Nd 0.9-x Ca x MnO y (0= 0.9 MnO y samples have been prepared in the 2.85= g -orbitals of manganese ions. Composition with y=2.85 is antiferromagnet with T N =85K, whereas for more oxidized Nd 0.9 MnO y samples a coexistence of antiferromagnetic and ferromagnetic phases is suggested. Low-temperature magnetic phase transition which is accompanied by a negative magnetization appearance has been found in the Nd 0.9 MnO 2.90 compound. Magnetic behavior of Nd 0.9-x Ca x MnO y (0.1= 1-x Ca x MnO 3 series. Properties of the Nd 0.9-x Ca x MnO y (0=< x=<0.4) solid solutions are in agreement with a hypothesis according to which a part of Nd ions can be substituted by Mn ions

Investigation on demagnetization of Nd2Fe14B permanent magnets induced by irradiation

Science.gov (United States)

Li, Zhefu; Jia, Yanyan; Liu, Renduo; Xu, Yuhai; Wang, Guanghong; Xia, Xiaobin

2017-12-01

Nd2Fe14B is an important component of insertion devices, which are used in synchrotron radiation sources, and could be demagnetized by irradiation. In the present study, the Monte Carlo code FLUKA was used to analyze the irradiation field of Nd2Fe14B, and it was confirmed that the main demagnetization particle was neutron. Nd2Fe14B permanent magnet samples were irradiated by Ar ions at different doses to simulate neutron irradiation damage. The hysteresis loops were measured using a vibrating sample magnetometer, and the microstructure evolutions were characterized by transmission electron microscopy. Moreover, the relationship between them was discussed. The results indicate that the decrease in saturated magnetization is caused by the changes in microstructure. The evolution of single crystals into an amorphous structure is the reason for the demagnetization phenomenon of Nd2Fe14B permanent magnets when considering its microscopic structure.

Hydrazinium lanthanide oxalates: synthesis, structure and thermal reactivity of N2H5[Ln2(C2O4)4(N2H5)]·4H2O, Ln = Ce, Nd.

Science.gov (United States)

De Almeida, Lucie; Grandjean, Stéphane; Rivenet, Murielle; Patisson, Fabrice; Abraham, Francis

2014-03-28

New hydrazinium lanthanide oxalates N2H5[Ln2(C2O4)4(N2H5)]·4H2O, Ln = Ce (Ce-HyOx) and Nd (Nd-HyOx), were synthesized by hydrothermal reaction at 150 °C between lanthanide nitrate, oxalic acid and hydrazine solutions. The structure of the Nd compound was determined from single-crystal X-ray diffraction data, space group P2₁/c with a = 16.315(4), b = 12.127(3), c = 11.430(2) Å, β = 116.638(4)°, V = 2021.4(7) Å(3), Z = 4, and R1 = 0.0313 for 4231 independent reflections. Two distinct neodymium polyhedra are formed, NdO9 and NdO8N, an oxygen of one monodentate oxalate in the former being replaced by a nitrogen atom of a coordinated hydrazinium ion in the latter. The infrared absorption band at 1005 cm(-1) confirms the coordination of N2H5(+) to the metal. These polyhedra are connected through μ2 and μ3 oxalate ions to form an anionic three-dimensional neodymium-oxalate arrangement. A non-coordinated charge-compensating hydrazinium ion occupies, with water molecules, the resulting tunnels. The N-N stretching frequencies of the infrared spectra demonstrate the existence of the two types of hydrazine ions. Thermal reactivity of these hydrazinium oxalates and of the mixed isotypic Ce/Nd (CeNd-HyOx) oxalate were studied by using thermogravimetric and differential thermal analyses coupled with gas analyzers, and high temperature X-ray diffraction. Under air, fine particles of CeO2 and Ce(0.5)Nd(0.5)O(1.75) are formed at low temperature from Ce-HyOx and CeNd-HyOx, respectively, thanks to a decomposition/oxidation process. Under argon flow, dioxymonocyanamides Ln2O2CN2 are formed.

Nd3-xBixFe4GaO12 (x = 2, 2.5 films on glass substrates prepared by MOD method

Directory of Open Access Journals (Sweden)

Yoshida T.

2014-07-01

Full Text Available We studied Nd3-XBiXFe4GaO12 films to obtain perpendicular magnetic anisotropy as well as large Faraday effect. NdBi2Fe4GaO12 (Bi2:NIGG and Nd0.5Bi2.5Fe4GaO12 (Bi2.5:NIGG films were obtained on Nd2BiFe4GaO12 (Bi1:NIGG layer prepared on glass substrates by metal-organic decomposition (MOD method. Bi2:NIGG and Bi2.5:NIGG films showed large Faraday rotation angles of 7.5 and 10.5 degree/µm, at a wavelength of 520 nm, respectively. Those films have perpendicular magnetic anisotropy with a coercivity of 350 Oe and a saturation magnetic field of 730 Oe.

The effects of Nd2O3 concentration in the laser emission of TeO2-ZnO glasses

Science.gov (United States)

Moreira, L. M.; Anjos, V.; Bell, M. J. V.; Ramos, C. A. R.; Kassab, L. R. P.; Doualan, D. J. L.; Camy, P.; Moncorgé, R.

2016-08-01

The present work reports the modification introduced by different Nd2O3 concentration on optical properties and the laser operation of Nd3+ doped (TeO2-ZnO) bulk tellurite glass. The spectroscopic data are analyzed within the Judd Ofelt formalism framework and the results are compared to the fluorescence lifetime and emission measurements to derive values for the quantum efficiency and the stimulated emission cross section of the considered 4F3/2 → 4I11/2 infrared laser transition around 1062.5 nm. Continuous-wave laser action is achieved with this bulk tellurite glass by pumping the sample inside a standard plan-concave mirror laser cavity with different output couplers. It is possible to observe coherent emission only for the lower concentration (0.5%(wt.) of Nd2 O3). Also laser action could only be observed for this sample with threshold pump power of 73 mW associated with a laser slope efficiency of 8% for an output coupler transmission of 4% indicating that TeO2-ZnO are potential materials for laser action. The results presented in this work together with those previously reported with higher concentration (1.0% (wt) of Nd2O3) determine the adequate Nd2O3 concentration for laser action and guide the correct experimental procedure for TeO2-ZnO glasses preparation.

Phase equilibrium of the system Ag-Fe-Nd, and Nd extraction from magnet scraps using molten silver

International Nuclear Information System (INIS)

Takeda, O.; Okabe, T.H.; Umetsu, Y.

2004-01-01

To develop a new recycling process, we examined the direct extraction of neodymium (Nd) metal from Nd-Fe-B magnet scraps using molten silver (Ag) as an extraction medium. Prior to the extraction experiment, the phase equilibrium of the system Ag-Fe-Nd was investigated to estimate the theoretical extraction limit. It was observed that the Fe/Nd 2 Fe 17 mixture equilibrates with the molten Ag-Nd alloy containing 50-52 mol% Nd (57-59 mass% Nd) at 1363 K. The experimental results were in good agreement with the thermodynamic calculation based on literature values. By reacting Nd-Fe-B magnet scraps with molten silver at 1273 K, more than 90% of the neodymium in the scrap was extracted, and an Ag-Nd alloy containing 40-50 mass% Nd was obtained. The neodymium in the Ag-Nd alloy was separated from silver as Nd 2 O 3 by oxidizing the obtained alloy in air. Although the wettability of Nd 2 O 3 with molten silver caused some difficulties in the separation of neodymium from silver, molten silver is shown to be an effective medium for neodymium extraction from magnet scrap

Microstructure and Magnetic Properties of NdFeB Films through Nd Surface Diffusion Process

Directory of Open Access Journals (Sweden)

Wenfeng Liu

2017-01-01

Full Text Available Ta/Nd/NdFeB/Nd/Ta films were deposited by magnetron sputtering on Si (100 substrates and subsequently annealed for 30 min at 923 K in vacuum. It was found that the microstructure and magnetic properties of Ta/Nd/NdFeB/Nd/Ta films strongly depend on the NdFeB layer thickness. With NdFeB layer thickness increasing, both the grain size and the strain firstly reduce and then increase. When NdFeB layer thickness is 750 nm, the strain reaches the minimum value. Meanwhile, both the in-plane and perpendicular coercivities firstly drastically increase and then slowly decrease with NdFeB layer thickness increasing. The highest in-plane and perpendicular coercivities can be obtained at NdFeB layer thickness of 750 nm, which are 21.2 kOe and 19.5 kOe, respectively. In addition, the high remanence ratio (remanent magnetization/saturation magnetization of 0.87 can also be achieved in Ta/Nd/NdFeB (750 nm/Nd/Ta film.

Hydrazinium lanthanide oxalates: synthesis, structure and thermal reactivity of N_2H_5[Ln_2(C_2O_4)_4(N_2H_5)].4H_2O, Ln = Ce, Nd

International Nuclear Information System (INIS)

De Almeida, Lucie; Grandjean, Stephane; Abraham, Francis; Rivenet, Murielle; Patisson, Fabrice

2014-01-01

New hydrazinium lanthanide oxalates N_2H_5[Ln_2(C_2O_4)_4(N_2H_5)].4H_2O, Ln = Ce (Ce-H_yO_x) and Nd (Nd- H_yO_x), were synthesized by hydrothermal reaction at 150 C between lanthanide nitrate, oxalic acid and hydrazine solutions. The structure of the Nd compound was determined from single-crystal X-ray diffraction data, space group P2_1/c with a = 16.315(4), b = 12.127(3), c = 11.430(2) Angstroms, β = 116.638(4) degrees, V = 2021.4(7) Angstroems"3, Z = 4, and R1 = 0.0313 for 4231 independent reflections. Two distinct neodymium polyhedra are formed, NdO_9 and NdO_8N, an oxygen of one monodentate oxalate in the former being replaced by a nitrogen atom of a coordinated hydrazinium ion in the latter. The infrared absorption band at 1005 cm"-"1 confirms the coordination of N_2H_5"+ to the metal. These polyhedra are connected through μ"2 and μ"3 oxalate ions to form an anionic three-dimensional neodymium-oxalate arrangement. A non-coordinated charge-compensating hydrazinium ion occupies, with water molecules, the resulting tunnels. The N-N stretching frequencies of the infrared spectra demonstrate the existence of the two types of hydrazine ions. Thermal reactivity of these hydrazinium oxalates and of the mixed isotypic Ce/Nd (CeNd-H_yO_x) oxalate were studied by using thermogravimetric and differential thermal analyses coupled with gas analyzers, and high temperature X-ray diffraction. Under air, fine particles of CeO_2 and Ce_0_._5Nd_0_._5O_1_._7_5 are formed at low temperature from Ce-H_yO_x and CeNd-H_yO_x, respectively, thanks to a decomposition/oxidation process. Under argon flow, dioxy-mono-cyanamides Ln_2O_2CN_2 are formed. (authors)

2nd Generation alkaline electrolysis. Final report

Energy Technology Data Exchange (ETDEWEB)

Yde, L. [Aarhus Univ. Business and Social Science - Centre for Energy Technologies (CET), Aarhus (Denmark); Kjartansdottir, C.K. [Technical Univ. of Denmark. DTU Mechanical Engineering, Kgs. Lyngby (Denmark); Allebrod, F. [Technical Univ. of Denmark. DTU Energy Conversion, DTU Risoe Campus, Roskilde (Denmark)] [and others

2013-03-15

The overall purpose of this project has been to contribute to this load management by developing a 2{sup nd} generation of alkaline electrolysis system characterized by being compact, reliable, inexpensive and energy efficient. The specific targets for the project have been to: 1) Increase cell efficiency to more than 88% (according to the higher heating value (HHV)) at a current density of 200 mA /cm{sup 2}; 2) Increase operation temperature to more than 100 degree Celsius to make the cooling energy more valuable; 3) Obtain an operation pressure more than 30 bar hereby minimizing the need for further compression of hydrogen for storage; 4) Improve stack architecture decreasing the price of the stack with at least 50%; 5) Develop a modular design making it easy to customize plants in the size from 20 to 200 kW; 6) Demonstrating a 20 kW 2{sup nd} generation stack in H2College at the campus of Arhus University in Herning. The project has included research and development on three different technology tracks of electrodes; an electrochemical plating, an atmospheric plasma spray (APS) and finally a high temperature and pressure (HTP) track with operating temperature around 250 deg. C and pressure around 40 bar. The results show that all three electrode tracks have reached high energy efficiencies. In the electrochemical plating track a stack efficiency of 86.5% at a current density of 177mA/cm{sup 2} and a temperature of 74.4 deg. C has been shown. The APS track showed cell efficiencies of 97%, however, coatings for the anode side still need to be developed. The HTP cell has reached 100 % electric efficiency operating at 1.5 V (the thermoneutral voltage) with a current density of 1. 1 A/cm{sup 2}. This track only tested small cells in an externally heated laboratory set-up, and thus the thermal loss to surroundings cannot be given. The goal set for the 2{sup nd} generation electrolyser system, has been to generate 30 bar pressure in the cell stack. An obstacle to be

Multiple Attribute Decision Making Based Relay Vehicle Selection for Electric Vehicle Communication

Directory of Open Access Journals (Sweden)

Zhao Qiang

2015-01-01

Full Text Available Large-scale electric vehicle integration into power grid and charging randomly will cause serious impacts on the normal operation of power grid. Therefore, it is necessary to control the charging behavior of electric vehicle, while information transmission for electric vehicle is significant. Due to the highly mobile characteristics of vehicle, transferring information to power grid directly might be inaccessible. Relay vehicle (RV can be used for supporting multi-hop connection between SV and power grid. This paper proposes a multiple attribute decision making (MADM-based RV selection algorithm, which considers multiple attribute, including data transfer rate, delay, route duration. It takes the characteristics of electric vehicle communication into account, which can provide protection for the communication services of electric vehicle charging and discharging. Numerical results demonstrate that compared to previous algorithm, the proposed algorithm offer better performance in terms of throughput, transmission delay.

Vehicle-to-vehicle communications : readiness of V2V technology for application.

Science.gov (United States)

2014-08-01

The purpose of this research report is to assess the readiness for application of vehicle-to-vehicle (V2V) : communications, a system designed to transmit basic safety information between vehicles to facilitate warnings to : drivers concerning impend...

Structural refinement of Nd[Fe(CN)6].4H2O and study of NdFeO3 obtained by its oxidative thermal decomposition at very low temperatures

International Nuclear Information System (INIS)

Navarro, M. Carolina; Pannunzio-Miner, Elisa V.; Pagola, Silvina; Gomez, M. Ines; Carbonio, Raul E.

2005-01-01

The crystal structure of Nd[Fe(CN) 6 ].4H 2 O has been refined by Rietveld analysis using high resolution synchrotron powder X-ray diffraction data. It belonged to the orthorhombic crystal system, Cmcm space group, with cell parameters: a=7.473952(1)A, b=12.919104(2)A and c=13.800549(2)A. The change in space group from P6 3 /m which is observed in the pentahydrates (LnFe(CN) 6 .5H 2 O) to Cmcm in the tetrahydrates has been analyzed to be a consequence of the change in 9-fold coordination of Nd 3+ in the pentahydrates to 8-fold coordination in the tetrahydrates, which changes the Nd 3+ environment from tricapped trigonal prism to a distorted tricapped trigonal prism or square antiprism. Its decomposition process in air to produce NdFeO 3 has been followed by thermogravimetric and differential thermal analysis, IR spectroscopy and laboratory powder XRD. We found that it is possible to synthesize crystalline NdFeO 3 at temperatures as low as 380 o C and refine the structure of single phase crystalline NdFeO 3 synthesized by this method at 600 deg. C

Relation between Nd2Fe14B grain alignment and coercive force decrease ratio in NdFeB sintered magnets

International Nuclear Information System (INIS)

Matsuura, Yutaka; Hoshijima, Jun; Ishii, Rintaro

2013-01-01

It was found that the coercive force of NdFeB sintered magnets decreases as the Nd 2 Fe 14 B grain alignment improves. Because of this phenomenon, studies looked at the relation between this alignment and the coercive force decrease ratio. In experiments, it was expected that the coercive force of perfectly aligned magnet reached 0.7 of coercive force in istotropically aligned magnet. When it is postulated that the coercive force is determined by the Stoner–Wohlfarth model, coercive force increases as the alignment improves and it becomes difficult to explain our experimental data. On the other hand, when the coercive force is determined by magnetic domain wall motion, the coercive force decreases as the alignment improves and the coercive force of the perfectly aligned magnet reaches 1/√(2) of the isotropically aligned magnet. This tendency and value was very close to our data. It strongly suggests that the coercive force of NdFeB sintered magnets is determined by the domain wall motion. - Highlights: ► Coercive force of NdFeB sintered magnets decreases as grains alignment improves. ► Coercive force decrease ratio reaches −30% at the perfect aligned magnet. ►These experimental results are different from the Stoner–Wohlfarth model. ► The magnetic domain wall motion could explain this coercive force decrease ratio

Four-wave-mixing and nonlinear cavity dumping of 280 picosecond 2nd Stokes pulse at 1.3 μm from Nd:SrMoO4 self-Raman laser

International Nuclear Information System (INIS)

Smetanin, S N; Ivleva, L I; Jelínek, M Jr; Kubeček, V; Jelínková, H; Shurygin, A S

2016-01-01

The 280 picosecond 2nd Stokes Raman pulses at 1.3 μm were generated directly from the miniature diode-pumped Nd:SrMoO 4 self-Raman laser. Using the 90° phase matching insensitive to the angular mismatch, the self-Raman laser allowed for the achievement of the four-wave-mixing generation of the 2nd Stokes Raman pulse directly in the active Nd:SrMoO 4 crystal at stimulated Raman scattering (SRS) self-conversion of the laser radiation. The passive Cr:YAG Q-switching and nonlinear cavity dumping was used without any phase locking device. (letter)

Feature interpretability and the positions of 2nd person possessives in Brazilian Portuguese

Directory of Open Access Journals (Sweden)

Bruna Karla Pereira

2016-12-01

Full Text Available Interpretability and valuation of φ-features (Chomsky, 2001; Pesetsky and Torrego, 2007 have played a central role in the investigation of language universals. With regard to that, in standard Brazilian Portuguese (BP, as well as in other Romance languages, possessives have uninterpretable number features, which are valued via nominal agreement. However, dialects of BP, especially the one spoken in Minas Gerais, have shown that 2nd person possessives, in postnominal position, do not have number agreement with the noun. In order to account for these facts, I will argue that, in this grammar, number features on 2nd person possessives are reanalyzed as being: (i associated with the person (rather than the noun and (ii interpretable. From the first postulation, ‘seu’ is expected to be the possessive for 2nd person singular, and ‘seus’ for 2nd person plural. From the second postulation, no number concord is expected to be triggered on the possessive. In addition, based on Danon (2011 and Norris (2014, I will argue that cardinals divide BP DPs into two domains in that phrases located above NumP are marked with the plural morpheme, while phrases below it are unmarked. In this sense, because prenominal possessives precede cardinals (NumP, they must be marked with the plural morpheme for nominal agreement; whereas postnominal possessives, which follow NumP, must be unmarked. Free from the plural marking associated with nominal agreement, postnominal 2nd person possessives favor the reanalysis of the morpheme ‘-s’ as indicating the number associated with person features.

Afs password expiration starts Feb 2nd 2004

CERN Multimedia

2004-01-01

Due to security reasons, and in agreement with CERN management, afs/lxplus passwords will fall into line with Nice/Mail passwords on February 2nd and expire annually. As of the above date afs account holders who have not changed their passwords for over a year will have a 60 day grace period to make a change. Following this date their passwords will become invalid. What does this mean to you? If you have changed your afs password in the past 10 months the only difference is that 60 days before expiration you will receive a warning message. Similar warnings will also appear nearer the time of expiration. If you have not changed your password for more than 10 months, then, as of February 2nd you will have 60 days to change it using the command ‘kpasswd'. Help to choose a good password can be found at: http://security.web.cern.ch/security/passwords/ If you have been given a temporary password at any time by the Helpdesk or registration team this will automatically fall into the expiration category ...

Microstructure characteristic and excellent corrosion protection properties of sealed Zn-TiO{sub 2} composite coating for sintered NdFeB magnet

Energy Technology Data Exchange (ETDEWEB)

Yang Xiaokui [School of Materials Science and Engineering, Southwest University, Chongqing 400715 (China); Li Qing, E-mail: liqingd@swu.edu.c [School of Chemistry and Chemical Engineering, Southwest University, Chongqing 400715 (China); Zhang Shiyan; Liu Fang; Wang Shaoyin; Zhang Haixiao [School of Chemistry and Chemical Engineering, Southwest University, Chongqing 400715 (China)

2010-04-09

In this paper, a protective sealed Zn-TiO{sub 2} composite coating (SCC) was prepared on sintered NdFeB magnet by electrodeposition and sol-gel combined technique. For a comparison, unsealed Zn-TiO{sub 2} composite coating (UCC) was also studied. The surface morphologies of composite coating were studied using scanning electron microscope (SEM). The microstructure of composite coatings and structure of sealing layer were studied by X-ray diffraction (XRD) and Fourier transform infrared (FT-IR) spectrum, respectively. The anticorrosive properties of composite coatings in neutral 3.5 wt.% NaCl solutions were evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) technique. The results of corrosion tests showed that due to the blocking effect of sealing layer, SCC could suppress the corrosion process by holding back the transfer or diffusion of corrosive medium, and therefore showed the excellent corrosion protection properties for sintered NdFeB magnet.

Proceedings of the 2nd Symposium on Laser Spectroscopy

International Nuclear Information System (INIS)

1994-11-01

This proceedings contains articles of the 2nd Symposium on Laser Spectroscopy. It was held on Nov 3-4, 1994 in Taejeon, Korea. The main topics are as follows: Laser Isotope, Laser Spectroscopy, Laser Fusion, Laser Applications and so on. (Yi, J. H.)

Magnetic excitations of Nd in Nd{sub 2-x}Ce{sub x}CuO{sub 4} (x=0,0.09,0.13)

Energy Technology Data Exchange (ETDEWEB)

Henggeler, W.; Furrer, A. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Chattopadyay, T.; Roessli, B. [Institut Max von Laue - Paul Langevin, 75 - Paris (France); Vorderwisch, P. [Hahn-Meitner-Institut Berlin GmbH (Germany); Thalmeier, P. [MPI Dresden (Germany)

1997-09-01

We have studied the wave vector dependence of the magnetic excitation spectrum of Nd in Nd{sub 2-x}Ce{sub x}CuO{sub 4} (x=0,0.09,0.13) by inelastic neutron scattering experiments on single crystals. The results are analyzed with the help of model calculations which are performed in the context of the mean field random-phase approximation. This enables us to obtain direct information on the coupling constants between the rare earth ions. (author) 1 fig., 2 refs.

Magnetic properties of ND Rich Melt-Spun ND-FE-B alloy

Directory of Open Access Journals (Sweden)

Grujić Aleksandar

2005-01-01

Full Text Available As a part of these experimental investigations of melt-spun Nd-Fe-B alloy with Nd rich content in relation to Nd2Fe14B prepared by rapid quenching process for optimally selected cooling rate and heat treatment, the influence of the chosen chemical composition on magnetic properties was observed. The results of X-ray diffraction, Mössbauer spectroscopy phase analysis and magnetic measurement of investigated melt-spun Nd14.5Fe78.5B7 alloy are presented to bring some new information concerning the relation between their structure and magnetic properties.

Development of a Hydrologic Characterization Technology for Fault Zones Phase II 2nd Report

Energy Technology Data Exchange (ETDEWEB)

Karasaki, Kenzi [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Doughty, Christine [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gasperikova, Erika [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Peterson, John [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Conrad, Mark [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Cook, Paul [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Tiemi, Onishi [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2011-03-31

This is the 2nd report on the three-year program of the 2nd phase of the NUMO-LBNL collaborative project: Development of Hydrologic Characterization Technology for Fault Zones under NUMO-DOE/LBNL collaboration agreement. As such, this report is a compendium of the results by Kiho et al. (2011) and those by LBNL.

Nd Fe{sub 10} Mo{sub 2} alloys production through reduction-diffusion for nitrogenation; Obtencao de ligas NdFe{sub 10}Mo{sub 2} por reducao-difusao para posterior nitrogenacao

Energy Technology Data Exchange (ETDEWEB)

Guilherme, Eneida da G. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil); Rechenberg, Hercilio R. [Sao Paulo Univ., SP (Brazil). Inst. de Fisica

1996-12-31

In this work we have examined the effect of various processing variables on the Nd Fe{sub 10} Mo{sub 2} phase formation by reduction-diffusion calciothermic process (R D C). The best results were obtained for 4 hours treatment at 950 deg C with 40% excess content Nd Cl{sub 3} and 50% excess content of Ca, for alloy Nd Fe{sub 10.5} Mo{sub 1.5}. Preliminary nitrogen absorption experiments have been done, without any further powder size reduction at temperatures between 300 and 350 deg C. (author) 9 refs., 6 figs., 1 tab.

The GNC Measurement System for the Automated Transfer Vehicle

Science.gov (United States)

Roux, Y.; da Cunha, P.

The Automated Transfer Vehicle (ATV) is a European Space Agency (ESA) funded spacecraft developed by EADS Space Transportation as prime contractor for the space segment together with major European industrial partners, in the frame of the International Space Station (ISS). Its mission objective is threefold : to supply the station with fret and propellant, to reboost ISS to a higher orbit and to dispose of waste from the station. The ATV first flight, called Jules Verne and planned on 2005, will be the first European Vehicle to perform an orbital rendezvous. The GNC Measurement System (GMS) is the ATV on board function in charge of the measurement data collection and preconditioning for the navigation, guidance and control (GNC) algorithms. The GMS is made up of hardware which are the navigation sensors (with a certain level of hardware redundancy for each of them), and of an on-board software that manages, monitors and performs consistency checks to detect and isolate potential sensor failures. The GMS relies on six kinds of navigation sensors, used during various phases of the mission : the gyrometers assembly (GYRA), the accelerometers assembly (ACCA), the star trackers (STR), the GPS receivers, the telegoniometers (TGM) and the videometers (VDM), the last two being used for the final rendezvous phase. The GMS function is developed by EADS Space Transportation together with other industrial partners: EADS Astrium, EADS Sodern, Laben and Dasa Jena Optronik.

Homogeneity of peraluminous SiO2-B2O3-Al2O3-Na2O-CaO-Nd2O3 glasses: Effect of neodymium content

International Nuclear Information System (INIS)

Gasnier, E.; Bardez-Giboire, I.; Massoni, N.; Montouillout, V.; Pellerin, N.; Allix, M.; Ory, S.; Cabie, M.; Poissonnet, S.; Massiot, D.

2014-01-01

Considering the interest of developing new glass matrices able to immobilize higher concentration of high level nuclear wastes than currently used nuclear borosilicate compositions, glasses containing high rare earth contents are of particular interest. This study focuses on a peraluminous alumino borosilicate system SiO 2 -B 2 O 3 -Al 2 O 3 -Na 2 O-CaO-Nd 2 O 3 defined by a per-alkaline/peraluminous ratio RP = ([Na 2 O] + [CaO])/ ([Na 2 O] + [CaO] + [Al 2 O 3 ]) ≤ 0.5. Samples with various contents of Nd 2 O 3 from 0 to 10 mol% were studied using DSC, XRD, SEM, TEM, STEM and EMPA methods. The glasses present a high thermal stability even after a slow cooling treatment from the melt. Only a slight mullite crystallization is detected for low Nd 2 O 3 content (≤2.3 mol%) and crystallization of a neodymium borosilicate crystalline phase combined to a phase separation occurred at high Nd 2 O 3 content (≥8 mol%). The solubility of neodymium in the presence of aluminum is demonstrated, with higher neodymium incorporation amounts than in per-alkaline glasses. (authors)

Modeling Dexterity Development in 2nd-4th-grade Boys by Means of Active Games

Directory of Open Access Journals (Sweden)

C. Марченко

2017-06-01

Full Text Available The objective is to optimize the mode of using game for dexterity development in the 2nd-4th-grade boys. Materials & methods: to conduct the experiment, there were eight test groups (n=48 formed in each class. The total number of such test groups was 24. The research relied on the following methods: theoretical analysis and collation of scientific and methodological literature; pedagogical testing; methods of mathematical experiment planning (complete factorial experiment 23; modeling method. Results: the research has determined that to develop dexterity, the 2nd-4th-grade boys need to participate in up to five games. The number of repetitions for the 2nd-3rd-graders is two, and for the 4th-graders – three, with 30–40-second rest intervals. The 2nd-4th-grade boys showed effective development during 40 classes, and the 3rd-grade boys – during 20 classes. After that, we recommend to use other means. The game duration varies from one to two minutes. Conclusions: the analysis of the scientific and methodological literature has revealed that the level of motor readiness, dexterity being one of its main components, largely determines the state of children’s physical and mental health. The research has found that the natural development of coordination abilities in boys aged between 7 and 10 is 22.5–80.0% (56.2% on average. Game actions play a particular role in dexterity development in junior schoolers. The 23 complete factorial experiment made it possible to study the multi-factorial structure of game load for the 2nd-4th-graders; to specify the relations between factors for their use during dexterity development in the 2nd-4th-grade boys in physical education classes. They can serve as an objective tool for the educational process optimization. The given regression equations are models that can be used to determine the optimal game means ratio in the academic process of the 2nd-4th-graders.

Preoperative clinical radioimmunodetection of pancreatic cancer by 111In-labeled chimeric monoclonal antibody Nd2

International Nuclear Information System (INIS)

Sawada, Tetsuji; Nishihara, Tamahiro; Yamamoto, Atsushi

1999-01-01

The present study was carried out with the purpose of evaluating the clinical usefulness of radioimmunodetection (RAID) with 111 In-labeled murine/human chimeric monoclonal antibody, Nd2 (c-Nd2) in patients with pancreatic cancer. Nineteen patients suspected to have pancreatic cancer were administered intravenously 74 MBq/2 mg 111 In-labeled c-Nd2 in 100 ml of saline containing 2% albumin over 30 min. A scintigram was obtained on the 3rd day after infusion by using single photon emission computed tomography (SPECT) imaging. Of the 14 patients finally diagnosed as having pancreatic cancer on the basis of surgical specimens or progress of disease, specific focal uptake at the site of the tumor was detected in 12 (true positive cases), representing a sensitivity of 85.7% (12/14), and liver metastasis was found in one case with metastasis. Of the 5 patients diagnosed with tumor-forming pancreatitis (TFP), 4 patients demonstrated true negative imaging, but one patient whose tumor demonstrated interesting findings in histology and immunostaining, showed false positive imaging. Of patients investigated for human anti-chimeric antibody (HACA) response, none showed HACA response, and no allergic reaction was seen in any of the patients administered c-Nd2. These results suggest that RAID with 111 In-labeled c-Nd2 is useful for differential preoperative diagnosis between invasive pancreatic cancer and TFP. (author)

Food irradiation - 2nd all-German conference. Proceedings

International Nuclear Information System (INIS)

Walz, E.; Ehlermann, D.A.E.

1993-01-01

The 2nd conference on 'Food Irradiation' in re-united Germany took place in Eggenstein-Leopoldshafen at the Karlsruhe Nuclear Research Centre, 9th to 10th December 1992. Participants came from government investigating agencies and research institutions of the German Federal Government and the Federal States. Abstracts focus on issues of food laws and certification of irradiation treatment. (UHE) [de

Soft and hard natures of Nd2Fe14B permanent magnet explored by first-order-reversal-curves

International Nuclear Information System (INIS)

Chen, Po-An; Yang, Chao-Yao; Chang, Shu-Jui; Lee, Min-Han; Tang, Nai-Kuang; Yen, Sheng-Chan; Tseng, Yuan-Chieh

2014-01-01

Two commercial Nd 2 Fe 14 B samples, MQP-B and sintered-NdFeB were investigated using synchrotron-based x-ray diffraction and first-order-reversal-curves (FORCs). Despite differing in magnetic and structural properties, the two samples were found to comprise two major ferromagnetic components in FORCs. For the sintered-NdFeB case, the soft component may originate from the intrinsically soft Nd-f site which was coupled with its local Fe atomic environment that differs in magnetic anisotropy from the Nd-g site (intrinsically hard). It may directly originate from the Nd-rich phase or microstructural imperfection, while the former possibility (Nd-f site) appears greater than the latter. While for the MQP-B, the minor second phase resulting from high structural disorder was likely in charge of the presence of the soft component. Sophisticated FORCs analyses revealed the natures of the soft and hard components, soft–hard coupling and switching reversibility of the two cases, irrespective of the origins of their two components. This provides insights to the origin of magnetic stability and reversal dynamics of Nd 2 Fe 14 B that have not been fully understood by conventional magnetic analyses. The coexistence of the two components led to an incoherent reversal undermining the magnetic stability of Nd 2 Fe 14 B. This is a fundamental problem as to why the performance extremity can only be improved finitely through extrinsic tuning. From FORCs simulation we understand that the soft–hard coupling was moderate in a real Nd 2 Fe 14 B compound. A stronger soft–hard coupling is necessary to conquer the anisotropic competition to enable a coherent reversal that will promote the magnetic hardness. - Highlights: • We investigated two commercially available Nd 2 Fe 14 B compounds with FORCs. • The two compounds were found to comprise soft and hard natures. • The coupling between the soft and hard phases is moderate in a real Nd 2 Fe 14 B

BaO-Nd2O3-CuOx subsolidus equilibria under carbonate-free conditions at pO2=100 Pa and at pO2=21 kPa

International Nuclear Information System (INIS)

Wong-Ng, W.; Cook, L.P.; Suh, J.; Coutts, R.; Stalick, J.K.; Levin, I.; Huang, Q.

2003-01-01

Subsolidus phase equilibria of the BaO-Nd 2 O 3 -CuO x system at pO 2 =100 Pa (0.1% O 2 volume fraction, 810 deg. C) and at pO 2 =21 kPa (21% O 2 volume fraction, 930 deg. C) have been investigated by applying controlled-atmosphere methods to minimize the presence of carbonate and CO 2 and H 2 O contamination. Under carbonate-free conditions, the BaO-Nd 2 O 3 -CuO x phase diagrams at pO 2 =100 Pa and at pO 2 =21 kPa are similar to one another except for differences in the extent of the solid solutions. Apart from the limiting binary phases, the ternary system consists of three solid solutions and one stoichiometric ternary compound. The first solid solution is the high T c series, Ba 2-x Nd 1+x Cu 3 O 6+z (0.3≥x≥0 at pO 2 =100 Pa; 0.95≥x≥ 0 at pO 2 =21 kPa). At pO 2 =21 kPa, a compositionally dependent phase change was detected, from tetragonal (0.7>x≥0) to orthorhombic (0.95≥x≥0.7). The second solid solution series, the 'brown-phase' Ba 1+x Nd 2-x CuO z , has a narrow homogeneity region (0.10>x≥0 at pO 2 =100 Pa; 0.15>x≥0 at pO 2 =21 kPa). In the high BaO part of the phase diagram, a third solid solution (Ba 2-x Nd x )CuO 3+z (x=0 to ∼ 0.3 at pO 2 =100 Pa; x=0-0.45 at pO 2 =21 kPa) was confirmed, as well as a nominally stoichiometric phase, Ba 4 Nd 2 Cu 2 O z . The latter phase is an insulator, with a structure comprised of unusual CuO 5 linear chains. A significant difference in tie line distribution involving the Ba 2-x Nd 1+x Cu 3 O 6+z superconductor was found under carbonate-free conditions relative to literature studies completed in air. Instead of the BaCuO 2+x -Ba 2+x Nd 4-x Cu 2 O z tie line normally encountered in air, a Ba 2-x Nd 1+x Cu 3 O 6+z -(Ba,Nd) 2 CuO 3+x tie line was established. This tie line substantially expands the field of stability of the Ba 2-x Nd 1+x Cu 3 O 6+z superconductor phase into the BaO-rich region of the phase diagram. Implications for the processing of materials based on the Ba 2-x Nd 1+x Cu 3 O 6+z

BIPHASIC TREATMENT OF 2ND CLASS ANGLE ANOMALIES

OpenAIRE

C. Romanec; R. Stanciu; Anca Telmecea; Valentina Dorobat

2011-01-01

Our approach aims at presenting, based on clinical observations and complementary examinations, the effects of a treatment’s setting up during the mixed dentition period. The objectives include the identification of the optimal time of treatment of II/1, II/2 Angle malocclusions, as well as the therapeutic possibilities for the treatment of 2nd class Angle malocclusion during the period of mixed and permanent dentition. The study is based on data collected from 114 cli...

Nd{sub 2±x}Zr{sub 2∓x}O{sub 7±x/2} (−0.2≤x≤0.4) complex oxides: Effect of anion disorder on ionic conductivity

Energy Technology Data Exchange (ETDEWEB)

Anithakumari, P., E-mail: anithakumari21-02@yahoo.co.in; Grover, V.; Tyagi, A. K. [Chemistry Division, Bhabha Atomic Research Centre, Mumbai, India-400085 (India)

2016-05-23

In the present work, a series of Nd{sub 2±x}Zr{sub 2∓x}O{sub 7±x/2} (−0.2≤x≤0.4) was prepared by self assisted gel-combution method followed by high temperature sintering at 1673 K. Thorough structural characterizations were done by X-ray diffraction and Raman spectroscopic techniques. The nominal compositions Nd{sub 1.6}Zr{sub 2.4}O{sub 7.2} and Nd{sub 1.8}Zr{sub 2.2}O{sub 7.1} were found to possess single-phasic pyrochlore structure whereas Nd{sub 2.0}Zr{sub 2.0}O{sub 7} and Nd{sub 2.2}Zr{sub 1.8}O{sub 6.9} consisted of a pyrochlore phase and a small amount of hexagonal Nd{sub 2}O{sub 3} as an impurity phase. Electrical behavior of the samples was examined by AC impedance analysis. Even though the activation energies of all the samples are not very different, a high pre-exponential factor for the Nd{sub 1.6}Zr{sub 2.4}O{sub 7.2} composition resulted in high ionic conductivity (3.37 × 10{sup −3} Scm{sup −1} at 773 K). This high ionic conductivity value makes it a superior candidate as an electrolyte material for SOFC applications.

Nd3+-doped TeO2-Bi2O3-ZnO transparent glass ceramics for laser application at 1.06 μm

Science.gov (United States)

Hu, Xiaolin; Luo, Zhiwei; Liu, Taoyong; Lu, Anxian

2017-04-01

The high crystallinity transparent glass ceramics based on Nd3+-doped 70TeO2-15Bi2O3-15ZnO (TBZ) compositions were successfully prepared by two-step heat treatment process. The effects of Nd2O3 content on the thermal, structural, mechanical, and optical properties of TBZ glass ceramics were studied. The incorporation of Nd2O3 enhanced the crystallization tendency in the matrix glass composition. The crystal phase and morphology of Bi2Te4O11 in the glass ceramics were confirmed by X-ray diffraction and field emission scanning electron microscopy. Due to precipitate more crystal phase, the hardness values increased from 3.21 to 3.66 GPa. Eight absorption peaks were observed from 400 to 900 nm and three emission bands appeared in the range of 850-1400 nm. With the increasing of Nd2O3 content from 0.5 to 2.5 wt%, the intensity of absorption peaks enhanced and the emission intensity increased up to 1.0 wt% and then fell down for further dopant concentration. The fluorescence decay lifetime decreased rapidly starting from 1.5 wt% Nd2O3 content due to the obvious energy migration among Nd3+. According to the extreme strong emission band around 1062 nm and the optimum Nd2O3 content (1.0 wt%), N10 glass ceramic was considered as a potential material for 1.06 μm laser applications.

Stable continuous-wave single-frequency Nd:YAG blue laser at 473 nm considering the influence of the energy-transfer upconversion.

Science.gov (United States)

Wang, Yaoting; Liu, Jianli; Liu, Qin; Li, Yuanji; Zhang, Kuanshou

2010-06-07

We report a continuous-wave (cw) single frequency Nd:YAG blue laser at 473 nm end-pumped by a laser diode. A ring laser resonator was designed, the frequency doubling efficiency and the length of nonlinear crystal were optimized based on the investigation of the influence of the frequency doubling efficiency on the thermal lensing effect induced by energy-transfer upconversion. By intracavity frequency doubling with PPKTP crystal, an output power of 1 W all-solid-state cw blue laser of single-frequency operation was achieved. The stability of the blue output power was better than +/- 1.8% in the given four hours.

One-stage thumb lengthening with use of an osteocutaneous 2nd metacarpal flap.

Science.gov (United States)

Givissis, Panagiotis; Stavridis, Stavros I; Ditsios, Konstantinos; Christodoulou, Anastasios

2009-12-01

Traumatic thumb amputation represents an extremely disabling entity, thus rendering its reconstruction a procedure of paramount importance. A case of a patient, who sustained a traumatic amputation of his left index finger at the metacarpophalangeal joint and of his left thumb in the middle of the proximal phalanx 4 months ago and was initially treated elsewhere, is described. For the thumb reconstruction, an osteocutaneous flap of the radial side of the 2nd metacarpal, which consisted of a 3, 5-cm bony segment with the overlying skin and its blood and nerve supply was used. The flap was transferred and fixed with a plate and screws to the palmar-medial side of the stump of the thumb, while the 1st web space was deepened by removing the rest of the second metacarpal, while a partial skin graft was used to cover a remaining gap. Thumb functionality was restored immediately postoperatively, and the overall result was satisfactory.

Heat Transfer Analysis in Wire Bundles for Aerospace Vehicles

Science.gov (United States)

Rickman, S. L.; Iamello, C. J.

2016-01-01

Design of wiring for aerospace vehicles relies on an understanding of "ampacity" which refers to the current carrying capacity of wires, either, individually or in wire bundles. Designers rely on standards to derate allowable current flow to prevent exceedance of wire temperature limits due to resistive heat dissipation within the wires or wire bundles. These standards often add considerable margin and are based on empirical data. Commercial providers are taking an aggressive approach to wire sizing which challenges the conventional wisdom of the established standards. Thermal modelling of wire bundles may offer significant mass reduction in a system if the technique can be generalized to produce reliable temperature predictions for arbitrary bundle configurations. Thermal analysis has been applied to the problem of wire bundles wherein any or all of the wires within the bundle may carry current. Wire bundles present analytical challenges because the heat transfer path from conductors internal to the bundle is tortuous, relying on internal radiation and thermal interface conductance to move the heat from within the bundle to the external jacket where it can be carried away by convective and radiative heat transfer. The problem is further complicated by the dependence of wire electrical resistivity on temperature. Reduced heat transfer out of the bundle leads to higher conductor temperatures and, hence, increased resistive heat dissipation. Development of a generalized wire bundle thermal model is presented and compared with test data. The steady state heat balance for a single wire is derived and extended to the bundle configuration. The generalized model includes the effects of temperature varying resistance, internal radiation and thermal interface conductance, external radiation and temperature varying convective relief from the free surface. The sensitivity of the response to uncertainties in key model parameters is explored using Monte Carlo analysis.

Thermodynamic optimization of the Cu-Nd system

International Nuclear Information System (INIS)

Wang Peisheng; Zhou Liangcai; Du Yong; Xu Honghui; Liu Shuhong; Chen Li; Ouyang Yifang

2011-01-01

Research highlights: → The enthalpies of formation of the compounds Cu 6 Nd, Cu 5 Nd, Cu 2 Nd and αCuNd were calculated using DFT. → The thermodynamic constraints to eliminate the artificial phase relations were imposed during the thermodynamic optimization procedure. → The Cu-Nd system was optimized under the thermodynamic constraints. - Abstract: The thermodynamic constraints to eliminate artificial phase relations were introduced with the Cu-Nd system as an example. The enthalpies of formation of the compounds Cu 6 Nd, Cu 5 Nd, Cu 2 Nd and αCuNd are calculated using density functional theory. Taking into account all the experimental data and the first-principles calculated enthalpies of formation of these compounds, the thermodynamic optimization of the Cu-Nd system was performed under the proposed thermodynamic constraints. It is demonstrated that the thermodynamic constraints are critical to obtain a set of thermodynamic parameters for the Cu-Nd system, which can avoid the appearance of all the artificial phase relations.

Crystal structures and phase transformation of deuterated lithium imide, Li2ND

International Nuclear Information System (INIS)

Balogh, Michael P.; Jones, Camille Y.; Herbst, J.F.; Hector, Louis G.; Kundrat, Matthew

2006-01-01

We have investigated the crystal structure of deuterated lithium imide, Li 2 ND, by means of neutron and X-ray diffraction. An order-disorder transition occurs near 360K. Below that temperature Li 2 ND can be described to the same level of accuracy as a disordered cubic (Fd3-bar m) structure with partially occupied Li 32e sites or as a fully occupied orthorhombic (Ima2 or Imm2) structure. The high temperature phase is best characterized as disordered cubic (Fm3-bar m) with D atoms randomized over the 192l sites. Density functional theory calculations complement and support the diffraction analyses. We compare our findings in detail with previous studies

Magnetic and structural properties of the Nd2(Fe100-xNbx)14B system prepared by arc melting

International Nuclear Information System (INIS)

Oyola Lozano, D.; Zamora, L. E.; Perez Alcazar, G. A.; Rojas, Y. A.; Bustos, H.; Greneche, J. M.

2006-01-01

In this work the magnetic and structural properties are investigated by Moessbauer spectrometry, Vibrating Sample Magnetometry and X-ray diffraction of Nd 2 (Fe 100-x Nb x ) 14 B powdered alloys with x = 0, 2 and 4 prepared by arc melting. The Moessbauer spectra of the samples were fitted with several contributions from: Nd 2 Fe 14 B, α-Fe and a paramagnetic phase associated with Nd 1.1 Fe 4 B 4 for x = 0 and additionally from NbFeB and Nd 2 Fe 17 for x = 2 and x = 4. The relative fractions of α-Fe and Nd 2 Fe 14 B are smaller for x = 4 than for x = 0, indicating that the amount of these two phases is reduced with increasing Nb content, while the relative fraction of Nd 2 Fe 17 increases. The α-Fe grain size slightly decreases while that of the Nd 2 Fe 14 B phase is increasing, when the Nb content increases. The hysteresis loops indicate that these samples behave as hard ferromagnets, with a coercive field which decreases when the Nb content increases, but with rather low remanent magnetization.

A chiral mixed carboxylate, [Nd4(H2O)2(OOC(CH2)3COO)4(C2O4)2], exhibiting NLO properties

International Nuclear Information System (INIS)

Vaidhyanathan, R.; Natarajan, Srinivasan; Rao, C.N.R.

2004-01-01

Reaction of a mixture of neodymium carbonate, HCl, oxamic acid and glutaric acid under hydrothermal conditions gives rise to a new mixed carboxylate of neodymium, [Nd 4 (H 2 O) 2 (OOC(CH 2 ) 3 COO) 4 (C 2 O 4 ) 2 ], I. The structure, determined using single crystal X-ray diffraction, comprises a helical column formed by the grafting of the oxalate unit on to helical NdO 9 chains, cross-linked by the glutarate anions. It is noteworthy that the pitch of the helix is equivalent to the length of the oxalate unit. Furthermore, I shows about 1.1 times the SHG activity of urea

Evaluation of Nd-Loaded SnO2:F Films Coated via Spray Pyrolysis

Science.gov (United States)

Turgut, G.

2018-07-01

Thin layers of single (F)- and double (F/Nd)-incorporated tin oxide have been coated on glass substrate via spray pyrolysis. The structural, morphological, electrical, and optical features of F-incorporated samples were evaluated depending on the Nd loading. X-ray diffraction analysis revealed that samples had tetragonal tin oxide structure with (211) and (200) preferential directions. The crystallite size and strain values varied from 37.98 nm and 1.21 × 10-3 to 52.12 nm and 1.88 × 10-3. Scanning electron microscopy analysis showed that the samples consisted of pyramidal, polyhedral, and needle-shaped granules. The lowest sheet resistance value of 1.22 Ω was found for 1.8 at.% Nd + 25 at.% F-coloaded SnO2. However, the widest optical bandgap of 4.01 eV was observed for the single 25 at.% F-loaded sample. The Urbach tail and figure of merit also changed in the ranges of 664 meV to 1296 meV and 6.4 × 10-2 Ω-1 to 2.3 × 10-3 Ω-1, respectively. The results presented herein indicate that the character of F-doped tin oxide films can be controlled by Nd loading and that these films could be useful for technological applications.

An investigation about the improvement of Tc for the n-type superconductor Nd2-xCexCuO4

International Nuclear Information System (INIS)

Wang Cong; Liang Jingkui; Chen Xiaolong; Min Jinrong; Cheng Xiangrong; Zhuang Weidong; Rao Guanghui

1994-01-01

Nd 2-x Ce x CuO 4 (x = 0.12 to 0.18) with T onset = 17 to 26 K is synthesized from the nominal composition of Nd 2-x Ce x CuO 4 + nSrCuO 2 (+nCaCuO 2 ) (n = 1, 2) under standard conditions without high pressure treatment. The sintering temperature, atmosphere, and synthetic procedure are important for the superconductivity of Nd 2-x Ce x CuO 4 . It is difficult to build up n blocks of SrCuO 2 , CaCuO 2 , or CdCuO 2 on Nd 2-x Ce x CuO 4 so as to add CuO 2 layers. In addition, the crystal structure and electrical resistance of Nd 2-x Ce x CuO 4 are studied. (orig.)

Commensurability oscillations in NdBa2Cu3Oy single crystals

Indian Academy of Sciences (India)

Postfach 3640, 76021 Karlsruhe, Germany. 2Technical ... the vortices are placed between the CuO2 layers, but the energy necessary for the elastic ... Two Nd123 crystals from the same batch were investigated: FK, twinned, transition tem-.

49 CFR 193.2513 - Transfer procedures.

Science.gov (United States)

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY LIQUEFIED NATURAL GAS FACILITIES... Practice.” (2) Before transfer, verify that each receiving container or tank vehicle does not contain any... volume of each receiving container or tank vehicle to ensure that expansion of the incoming fluid due to...

2nd International Conference on Green Communications and Networks 2012

CERN Document Server

Ma, Maode; GCN 2012

2013-01-01

The objective of the 2nd International Conference on Green Communications and Networks 2012 (GCN 2012) is to facilitate an exchange of information on best practices for the latest research advances in the area of communications, networks and intelligence applications. These mainly involve computer science and engineering, informatics, communications and control, electrical engineering, information computing, and business intelligence and management. Proceedings of the 2nd International Conference on Green Communications and Networks 2012 (GCN 2012) will focus on green information technology and applications, which will provide in-depth insights for engineers and scientists in academia, industry, and government. The book addresses the most innovative research developments including technical challenges, social and economic issues, and presents and discusses the authors’ ideas, experiences, findings, and current projects on all aspects of advanced green information technology and applications. Yuhang Yang is ...

Isotopic effect in phase transitions of (NH4)2HPO4 and (ND4)2DPO4

International Nuclear Information System (INIS)

Diosa, J.E.; Coral, E.E.; Vargas, R.A.

1996-01-01

Specific heat and dielectric constant measurements at low frequency, have shown two transitions in the ionic systems (NH4)2HPO4 and (ND4)2DPO4 bellow 300 K. For (NH4)2HPO4, the transition are observed at 174 K and 246 K, while (ND4)2DPO4, they are observed at 147 K and 229 K. We have also found a shift of the transition temperatures to smaller values when the hydrogen is replaced by deuterium. The specific heat anomalies associated with these transitions are reversible in successive thermal cycles (heating and cooling) and we did not detect latent heat through them. Furthermore, we have detected anomalies in the dielectric constant in the same transition points. We have attributed these transition phases to reorientations of the tetrahedra of NH4 and ND4, so that the activation energy Ea for these process that we associated with the thermal energy KBTt required for the transition, is inversely related to the mass of the hydrogen isotope

10 kW Contactless Power Transfer System for Rapid Charger of Electric Vehicle

OpenAIRE

Yamanaka, Tomohiro; Kaneko, Yasuyoshi; Abe, Shigeru; Yasuda, Tomio

2012-01-01

A contactless power transfer system for charging electric vehicles requires a high efficiency, a large air gap, and a good tolerance to lateral misalignment and needs to be compact and lightweight. A double-sided winding 10 kW transformer based on a 1.5 kW H-shaped core transformer was developed for a rapid charger. Even though the transformer capacity was increased, the dimensions of the 10 kW transformer were almost the same as those of the 1.5 kW transformer. In this paper, the design conc...

2nd International Conference on Nuclear Physics in Astrophysics

CERN Document Server

Fülöp, Zsolt; Somorjai, Endre; The European Physical Journal A : Volume 27, Supplement 1, 2006

2006-01-01

Launched in 2004, "Nuclear Physics in Astrophysics" has established itself in a successful topical conference series addressing the forefront of research in the field. This volume contains the selected and refereed papers of the 2nd conference, held in Debrecen in 2005 and reprinted from "The European Physical Journal A - Hadrons and Nuclei".

Relation between Nd{sub 2}Fe{sub 14}B grain alignment and coercive force decrease ratio in NdFeB sintered magnets

Energy Technology Data Exchange (ETDEWEB)

Matsuura, Yutaka, E-mail: Yutaka_Matsuura@hitachi-metals.co.jp [Hitachi Metals Ltd., NEOMAX Division, 2-15-17 Egawa, Shimamoto-cho, Mishima-gun, Osaka 618-0013 (Japan); Hoshijima, Jun; Ishii, Rintaro [Hitachi Metals Ltd., NEOMAX Division, 2-15-17 Egawa, Shimamoto-cho, Mishima-gun, Osaka 618-0013 (Japan)

2013-06-15

It was found that the coercive force of NdFeB sintered magnets decreases as the Nd{sub 2}Fe{sub 14}B grain alignment improves. Because of this phenomenon, studies looked at the relation between this alignment and the coercive force decrease ratio. In experiments, it was expected that the coercive force of perfectly aligned magnet reached 0.7 of coercive force in istotropically aligned magnet. When it is postulated that the coercive force is determined by the Stoner–Wohlfarth model, coercive force increases as the alignment improves and it becomes difficult to explain our experimental data. On the other hand, when the coercive force is determined by magnetic domain wall motion, the coercive force decreases as the alignment improves and the coercive force of the perfectly aligned magnet reaches 1/√(2) of the isotropically aligned magnet. This tendency and value was very close to our data. It strongly suggests that the coercive force of NdFeB sintered magnets is determined by the domain wall motion. - Highlights: ► Coercive force of NdFeB sintered magnets decreases as grains alignment improves. ► Coercive force decrease ratio reaches −30% at the perfect aligned magnet. ►These experimental results are different from the Stoner–Wohlfarth model. ► The magnetic domain wall motion could explain this coercive force decrease ratio.

Reconstructing the Nd oceanic cycle using a coupled dynamical – biogeochemical model

Directory of Open Access Journals (Sweden)

T. Arsouze

2009-12-01

Full Text Available The decoupled behaviour observed between Nd isotopic composition (Nd IC, also referred as ε_Nd and Nd concentration cycles has led to the notion of a "Nd paradox". While ε_Nd behaves in a quasi-conservative way in the open ocean, leading to its broad use as a water-mass tracer, Nd concentration displays vertical profiles that increase with depth, together with a deep-water enrichment along the global thermohaline circulation. This non-conservative behaviour is typical of nutrients affected by scavenging in surface waters and remineralisation at depth. In addition, recent studies suggest the only way to reconcile both concentration and Nd IC oceanic budgets, is to invoke a "Boundary Exchange" process (BE, defined as the co-occurrence of transfer of elements from the margin to the sea with removal of elements from the sea by Boundary Scavenging as a source-sink term. However, these studies do not simulate the input/output fluxes of Nd to the ocean, and therefore prevents from crucial information that limits our understanding of Nd decoupling. To investigate this paradox on a global scale, this study uses for the first time a fully prognostic coupled dynamical/biogeochemical model with an explicit representation of Nd sources and sinks to simulate the Nd oceanic cycle. Sources considered include dissolved river fluxes, atmospheric dusts and margin sediment re-dissolution. Sinks are scavenging by settling particles. This model simulates the global features of the Nd oceanic cycle well, and produces a realistic distribution of Nd concentration (correct order of magnitude, increase with depth and along the conveyor belt, 65% of the simulated values fit in the ±10 pmol/kg envelop when compared to the data and isotopic composition (inter-basin gradient, characterization of the main water-masses, more than 70% of the simulated values fit in the ±3 ε_Nd envelop when compared to the data, though a slight overestimation of

Lifetimes of low-lying states in 132Nd and 134Nd

International Nuclear Information System (INIS)

Kruecken, R.; Mullins, S.M.; Thornley, D.J.; Kirwan, A.J.; Nolan, P.J.; Regan, P.H.; Wadsworth, R.

1995-01-01

Lifetimes of low-lying states have been measured in 132 Nd and 134 Nd using the coincidence-plunger technique. The reaction 32 S+ 105 Pd was used at a bombarding energy of 152 MeV. The measurement has been performed at the NSF Daresbury using the ESSA 30 array. The differential decay-curve method (DDCM) was used to analyze the recoil-distance Doppler-shift (RDDS) data. The experimental B(E2) values in 132 Nd are well described by the predictions of the rotational model and the IBM in the O(6) limit. ((orig.))

Pentacene based thin film transistors with high-k dielectric Nd2O3 as a gate insulator

International Nuclear Information System (INIS)

Sarma, R.; Saikia, D.

2010-01-01

We have investigated the pentacene based Organic Thin Film Transistors (OTFTs) with high-k dielectric Nd 2 O 3 . Use of high dielectric constant (high-k) gate insulator Nd 2 O 3 reduces the threshold voltage and sub threshold swing of the OTFTs. The calculated threshold voltage -2.2V and sub-threshold swing 1V/decade, current ON-OFF ratio is 1.7 X 10 4 and mobility is 0.13cm 2 /V.s. Pentacene film is deposited on Nd 2 O 3 surface using two step deposition method. Deposited pentacene film is found poly crystalline in nature. (author)

Microstructure evolution and coercivity enhancement in Nd-Fe-B thin films diffusion-processed by R-Al alloys (R=Nd, Pr)

Science.gov (United States)

Xie, Yigao; Yang, Yang; Zhang, Tongbo; Fu, Yanqing; Jiang, Qingzheng; Ma, Shengcan; Zhong, Zhenchen; Cui, Weibin; Wang, Qiang

2018-05-01

Diffusion process by Nd-Al and Pr-Al alloys was compared and investigated in Nd-Fe-B thin films. Enhanced coercivity 2.06T and good squareness was obtained by using Pr85Al15 and Nd85Al15 alloys as diffusion sources. But the coercivity of diffusion-processed thin films by Pr70Al30 and Pr55Al45 alloys decreased to 2.04T and 1.82T. High ambient coercivity of 2.26T was achieved in diffusion-processed thin film by Nd70Al30 leading to an improved coercivity thermal stability because Nd2Fe14B grains were enveloped by Nd-rich phase as seen by transmission electron microscopy Nd-loss image. Meanwhile, microstructure-dependent parameters α and Neff were improved. However, high content of Al in diffusion-processed thin film by Nd55Al45 lead to degraded texture and coercivity.

Energy and polarization dependence of resonant inelastic X-ray scattering in Nd2CuO4

International Nuclear Information System (INIS)

Hill, J.P.; Kao, C.C.; Haemaelaeinen, K.

1998-01-01

The authors report the energy and polarization dependence of resonant inelastic x-ray scattering from Nd 2 CuO 4 . An energy loss feature at ∼6 eV is observed in the vicinity of the Cu K-edge. Numerical calculations based on the Anderson impurity model identify this as a charge transfer excitation to the anti-bonding state. The incident polarization is shown to select the intermediate states participating in the resonance process. Resonances are observed at 8,990 eV and 9,000 eV with the incident polarization perpendicular and parallel to the CuO planes, respectively. In contrast to the single-site model calculations, no resonances are observed associated with the 1s3d 10 L intermediate states, suggesting non-local effects play a role

Concentration quenching in Nd-doped glasses

International Nuclear Information System (INIS)

Stokowski, S.E.; Cook, L.; Mueller, H.; Weber, M.J.

1984-01-01

Fluorescence from trivalent Nd in solids is unfortunately quenched by interactions between Nd ions. Thus, laser materials with high Nd concentrations have reduced efficiencies because of this self-quenching, also known as concentration quenching. Nd self-quenching in different crystals and glasses varies considerably. We are therefore investigating this effect in a large number of materials in an effort to: (1) find those materials with long Nd fluorescent lifetimes at high Nd concentrations; and (2) elucidate the basic mechanisms of quenching and how the material structure controls its magnitude. We have concentrated on Nd-doped glasses because they provide a rich variety of structures, albeit complicated by Nd site inhomogeneities, and are easily and quickly made

Effect of V-Nd co-doping on phase transformation and grain growth process of TiO2

Science.gov (United States)

Khatun, Nasima; Amin, Ruhul; Anita, Sen, Somaditya

2018-05-01

The pure and V-Nd co-doped TiO2 samples are prepared by the modified sol-gel process. The phase formation is confirmed by XRD spectrum. Phase transformation is delayed in V-Nd co-doped TiO2 (TVN) samples compared to pure TiO2. The particle size is comparatively small in TVN samples at both the temperature 450 °C and 900 °C. Hence the effect of Nd doping is dominated over V doping in both phase transformation and grain growth process of TiO2.

Interplay of structural chemistry and magnetism in perovskites; A study of CaLn2Ni2WO9; Ln=La, Pr, Nd

Science.gov (United States)

Chin, Chun-Mann; Paria Sena, Robert; Hunter, Emily C.; Hadermann, Joke; Battle, Peter D.

2017-07-01

Polycrystalline samples of CaLn2Ni2WO9 (Ln=La, Pr, Nd) have been synthesized and characterised by a combination of X-ray and neutron diffraction, electron microscopy and magnetometry. Each composition adopts a perovskite-like structure with a 5.50, b 5.56, c 7.78 Å, β 90.1° in space group P21/n. Of the two crystallographically distinct six-coordinate sites, one is occupied entirely (Ln=Pr) or predominantly (Ln=La, Nd) by Ni2+ and the other by Ni2+ and W6+ in a ratio of approximately 1:2. None of the compounds shows long-range magnetic order at 5 K. The magnetometry data show that the magnetic moments of the Ni2+ cations form a spin glass below 30 K in each case. The Pr3+ moments in CaPr2Ni2WO9 also freeze but the Nd3+ moments in CaNd2Ni2WO9 do not. This behaviour is contrasted with that observed in other (A,A')B2B'O9 perovskites.

Functional separation of oxidation–reduction reactions and electron transport in PtRu/ND and conductive additive hybrid electrocatalysts during methanol oxidation

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yan; Wang, Yanhui [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Bian, Linyan [College of Physics and Chemistry, Henan Polytechnic University, Jiaozuo, Henan 454000 (China); Lu, Rui [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Zang, Jianbing, E-mail: jbzang@ysu.edu.cn [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China)

2016-02-28

Graphical abstract: - Highlights: • Functional separation of reactions and electron transport in PtRu/ND + AB (or CNT). • A conductive network was formed after the addition of AB or CNT. • PtRu/ND + AB (or CNT) exhibited enhanced activity and stability than PtRu/ND. - Abstract: Undoped nanodiamond (ND) supported PtRu (PtRu/ND) electrocatalyst for methanol oxidation reactions (MOR) in direct methanol fuel cells was prepared by a microwave-assisted polyol reduction method. Sp{sup 3}-bonded ND possesses high electrochemical stability but low conductivity, while sp{sup 2}-bonded carbon nanomaterials with high conductivity are prone to oxidation. Therefore, the functions of the supporting material were separated in this study. ND (sp{sup 3}), as a support, and AB or CNTs (sp{sup 2}), as a conductive additive, were combined to form the hybrid electrocatalysts PtRu/ND + AB and PtRu/ND + CNT for MOR. The morphology of the electrocatalysts was characterized by scanning electron microscopy and electrochemical measurements were performed using an electrochemical workstation. The results indicated that the electrocatalytic activity of PtRu/ND for MOR was improved with the addition of AB or CNTs as a conductive additive. Moreover, adding CNTs to PtRu/ND as a conductive additive showed better electrocatalytic activities than adding AB, which can be ascribed to the better electron-transfer ability of CNTs.

Large positive magnetoresistance in intermetallic compound NdCo2Si2

Science.gov (United States)

Roy Chowdhury, R.; Dhara, S.; Das, I.; Bandyopadhyay, B.; Rawat, R.

2018-04-01

The magnetic, magneto-transport and magnetocaloric properties of antiferromagnetic intermetallic compound NdCo2Si2 (TN = 32K) have been studied. The compound yields a positive magnetoresistance (MR) of about ∼ 123 % at ∼ 5K in 8 T magnetic field. The MR value is significantly large vis - a - vis earlier reports of large MR in intermetallic compounds, and possibly associated with the changes in magnetic structure of the compound. The large MR value can be explained in terms of field induced pseudo-gaps on Fermi surface.

BIPHASIC TREATMENT OF 2ND CLASS ANGLE ANOMALIES

Directory of Open Access Journals (Sweden)

C. Romanec

2011-09-01

Full Text Available Our approach aims at presenting, based on clinical observations and complementary examinations, the effects of a treatment’s setting up during the mixed dentition period. The objectives include the identification of the optimal time of treatment of II/1, II/2 Angle malocclusions, as well as the therapeutic possibilities for the treatment of 2nd class Angle malocclusion during the period of mixed and permanent dentition. The study is based on data collected from 114 clinical cases (69 girls and 45 boys with an age span between 7 and 18 years.

2nd National Conference on Theoretical Physics. Abstracts Book

International Nuclear Information System (INIS)

Grecu, Alexandru Tudor

2004-01-01

The 2nd National Conference on Theoretical Physics was held on 26-29 August 2004 in Constanta, Romania. The addressed physics fields within the INIS scope are as follows: classical and quantum mechanics, general physics, physics of elementary particles and fields, nuclear physics and radiation physics, classical and quantum mechanics, general physics, atomic and molecular physics, condensed matter physics

In situ preparation of (TiB + TiC + Nd2O3)/Ti composites by powder metallurgy

International Nuclear Information System (INIS)

Lu Junqiang; Qin Jining; Lu Weijie; Liu Yang; Gu Jiajun; Zhang Di

2009-01-01

Titanium matrix composites reinforced with multiple ceramic particulates TiB, TiC and Nd 2 O 3 were prepared by powder metallurgy utilizing the chemical reactions among Ti, B 4 C, NdB 6 and oxygen in Ti powder. The thermodynamic feasibility of the in situ reaction has been calculated. The phases were identified by X-ray diffraction (XRD). The result shows that multiple ceramic phases TiB, TiC and Nd 2 O 3 particulates have been synthesized. The microstructures were examined by means of optical microscopy (OM), scanning electron microscopy (SEM), backscattered electron microscopy and transmission electron microscope (TEM). The results show that the reinforcements are distributed uniformly in the matrix alloy and grow in different shapes. TiB grows in needle shape; TiC and Nd 2 O 3 grow in equiaxed or near-equiaxed shapes. The addition of NdB 6 is beneficial to grain refinement, grain-boundary purification and porosity reduction

3-D laser confocal microscopy study of the oxidation of NdFeB magnets in atmospheric conditions

International Nuclear Information System (INIS)

Meakin, J.P.; Speight, J.D.; Sheridan, R.S.; Bradshaw, A.; Harris, I.R.; Williams, A.J.; Walton, A.

2016-01-01

Highlights: • Room temperature atmospheric oxidation behaviour of sintered NdFeB. • 3D laser confocal microscopy measurement of oxide phase growth. • Significant height increase of oxide phase only observed at triple points. • Raman spectroscopy identified oxide phase to be Nd 2 O 3 . • Diffusion coefficient determined to be 4 × 10 −13 cm 2 /s. - Abstract: Neodymium iron boron (NdFeB) magnets are used in a number of important applications, such as generators in gearless wind turbines, motors in electric vehicles and electronic goods (e.g.— computer hard disk drives, HDD). Hydrogen can be used as a processing gas to separate and recycle scrap sintered Nd-Fe-B magnets from end-of-life products to form a powder suitable for recycling. However, the magnets are likely to have been exposed to atmospheric conditions prior to processing, and any oxidation could lead to activation problems for the hydrogen decrepitation reaction. Many previous studies on the oxidation of NdFeB magnets have been performed at elevated temperatures; however, few studies have been formed under atmospheric conditions. In this paper a combination of 3-D laser confocal microscopy and Raman spectroscopy have been used to assess the composition, morphology and rate of oxidation/corrosion on scrap sintered NdFeB magnets. Confocal microscopy has been employed to measure the growth of surface reaction products at room temperature, immediately after exposure to air. The results showed that there was a significant height increase at the triple junctions of the Nd-rich grain boundaries. Using Raman spectroscopy, the product was shown to consist of Nd 2 O 3 and formed only on the Nd-rich triple junctions. The diffusion coefficient of the triple junction reaction product growth at 20 °C was determined to be approximately 4 × 10 −13 cm 2 /sec. This value is several orders of magnitude larger than values derived from the diffusion controlled oxide growth observations at elevated

3-D laser confocal microscopy study of the oxidation of NdFeB magnets in atmospheric conditions

Energy Technology Data Exchange (ETDEWEB)

Meakin, J.P., E-mail: jxm764@bham.ac.uk; Speight, J.D.; Sheridan, R.S.; Bradshaw, A.; Harris, I.R.; Williams, A.J.; Walton, A.

2016-08-15

Highlights: • Room temperature atmospheric oxidation behaviour of sintered NdFeB. • 3D laser confocal microscopy measurement of oxide phase growth. • Significant height increase of oxide phase only observed at triple points. • Raman spectroscopy identified oxide phase to be Nd{sub 2}O{sub 3}. • Diffusion coefficient determined to be 4 × 10{sup −13} cm{sup 2}/s. - Abstract: Neodymium iron boron (NdFeB) magnets are used in a number of important applications, such as generators in gearless wind turbines, motors in electric vehicles and electronic goods (e.g.— computer hard disk drives, HDD). Hydrogen can be used as a processing gas to separate and recycle scrap sintered Nd-Fe-B magnets from end-of-life products to form a powder suitable for recycling. However, the magnets are likely to have been exposed to atmospheric conditions prior to processing, and any oxidation could lead to activation problems for the hydrogen decrepitation reaction. Many previous studies on the oxidation of NdFeB magnets have been performed at elevated temperatures; however, few studies have been formed under atmospheric conditions. In this paper a combination of 3-D laser confocal microscopy and Raman spectroscopy have been used to assess the composition, morphology and rate of oxidation/corrosion on scrap sintered NdFeB magnets. Confocal microscopy has been employed to measure the growth of surface reaction products at room temperature, immediately after exposure to air. The results showed that there was a significant height increase at the triple junctions of the Nd-rich grain boundaries. Using Raman spectroscopy, the product was shown to consist of Nd{sub 2}O{sub 3} and formed only on the Nd-rich triple junctions. The diffusion coefficient of the triple junction reaction product growth at 20 °C was determined to be approximately 4 × 10{sup −13} cm{sup 2}/sec. This value is several orders of magnitude larger than values derived from the diffusion controlled oxide growth

Distance Dependence of Path Loss for Millimeter Wave Inter-Vehicle Communications

Directory of Open Access Journals (Sweden)

M. Fujise

2004-12-01

Full Text Available Millimeter-wave path loss between two cars was measured to obtainthe general applicable distance for inter-vehicle communication systemsin real environments. An abrupt and substantial increase in path lossdue to interruption, curves, and different-lane traveling has been amajor concern in inter-vehicle communications. The path lossmeasurements were carried out using 60-GHz CW radiowaves and standardhorn antennas on metropolitan highways and regular roads. Because thepropagation loss is traffic-dependent, the highways were classifiedinto uncrowded and crowded highways, and the regular roads wereclassified into uncrowded and crowded roads. The path loss for thehighways exhibited 2nd-power-law attenuation and that for the regularroads exhibited 1st-power-law attenuation with an increase ininter-vehicle distance. Additional losses of 15 dB for the highways and5 dB for the regular roads were observed when the inter-vehicledistance was more than approximately 30 m. Thus, we were able todemonstrate millimeter-wave inter-vehicle communications at aninter-vehicle distance of more than 100 m.

YBa2Cu3O7-δ/NdBa2(Cu1-xNix)3O7-δ double layers by liquid-phase epitaxial growth

International Nuclear Information System (INIS)

Yao, X.; Izumi, Toru; Hobara, Natsuro; Nakamura, Yuichi; Izumi, Teruo; Shiohara, Yuh

2001-01-01

Our present investigation has answered questions pertaining to the REBa 2 Cu 3 O 7-δ (RE123, RE=rare-earth elements)-coated conductor application when NdBa 2 (Cu 1-x Ni x ) 3 O 7-δ (Ni-NdBCO) solid solution is used as a buffer layer by the liquid-phase epitaxy(LPE) process. The NiO/Ni substrate has no substantial reaction in the Ni-saturated Nd-Ba-Cu-O liquid. There is no essential Ni interdiffusion between YBa 2 Cu 3 O 7-δ (YBCO) and Ni-NdBCO LPE thick films as evident from T c values of 90 K obtained from multilayer YBCO/Ni-NdBCO samples. (author)

Conventional and Bimodal Nuclear Thermal Rocket (NTR) Artificial Gravity Mars Transfer Vehicle Concepts

Science.gov (United States)

Borowski, Stanley K.; McCurdy, David R.; Packard, Thomas W.

2016-01-01

A variety of countermeasures have been developed to address the debilitating physiological effects of zero-gravity (0-g) experienced by cosmonauts and astronauts during their approximately 0.5 to 1.2 year long stays in low Earth orbit (LEO). Longer interplanetary flights, combined with possible prolonged stays in Mars orbit, could subject crewmembers to up to approximately 2.5 years of weightlessness. In view of known and recently diagnosed problems associated with 0-g, an artificial gravity (AG) spacecraft offers many advantages and may indeed be an enabling technology for human flights to Mars. A number of important human factors must be taken into account in selecting the rotation radius, rotation rate, and orientation of the habitation module or modules. These factors include the gravity gradient effect, radial and tangential Coriolis forces, along with cross-coupled acceleration effects. Artificial gravity Mars transfer vehicle (MTV) concepts are presented that utilize both conventional NTR, as well as, enhanced bimodal nuclear thermal rocket (BNTR) propulsion. The NTR is a proven technology that generates high thrust and has a specific impulse (Isp) capability of approximately 900 s-twice that of today's best chemical rockets. The AG/MTV concepts using conventional Nuclear Thermal Propulsion (NTP) carry twin cylindrical International Space Station (ISS)- type habitation modules with their long axes oriented either perpendicular or parallel to the longitudinal spin axis of the MTV and utilize photovoltaic arrays (PVAs) for spacecraft power. The twin habitat modules are connected to a central operations hub located at the front of the MTV via two pressurized tunnels that provide the rotation radius for the habitat modules. For the BNTR AG/MTV option, each engine has its own closed secondary helium(He)-xenon (Xe) gas loop and Brayton Rotating Unit (BRU) that can generate 10s of kilowatts (kWe) of spacecraft electrical power during the mission coast phase

Specific features of the domain structure of (Gd sub 1-x Nd sub x ) sub 2 (MoO sub 4 ) sub 3 crystals. Osobennosti domennoj struktury kristallov (Gd sub 1-x Nd sub x ) sub 2 (MoO sub 4 ) sub 3

Energy Technology Data Exchange (ETDEWEB)

Bryzgalov, A N; Slepchenko, B M; Virachev, B P [Cherepovetskij Gosudarstvennyj Pedagogicheskij Inst., Cherepovets (USSR)

1989-11-01

Formation of the domain structures by sample transfer into thermodynamically metastable state using a simultaneous effect of electric field and temperature change is investigated in Gd{sub 1.7}Nd{sub 0.3}(MoO{sub 4}){sub 3} monocrystals (GMO). Some new results obtained under investigations into GMO domain structure using neodymium by means of hydrothermal etching and polarization-optical method are presented.

Short rare hTERT-VNTR2-2nd alleles are associated with prostate cancer susceptibility and influence gene expression

International Nuclear Information System (INIS)

Yoon, Se-Lyun; Cheon, Sang-Hyeon; Leem, Sun-Hee; Jung, Se-Il; Do, Eun-Ju; Lee, Se-Ra; Lee, Sang-Yeop; Chu, In-Sun; Kim, Wun-Jae; Jung, Jaeil; Kim, Choung Soo

2010-01-01

The hTERT (human telomerase reverse transcriptase) gene contains five variable number tandem repeats (VNTR) and previous studies have described polymorphisms for hTERT-VNTR2-2 nd . We investigated how allelic variation in hTERT-VNTR2-2 nd may affect susceptibility to prostate cancer. A case-control study was performed using DNA from 421 cancer-free male controls and 329 patients with prostate cancer. In addition, to determine whether the VNTR polymorphisms have a functional consequence, we examined the transcriptional levels of a reporter gene linked to these VNTRs and driven by the hTERT promoter in cell lines. Three new rare alleles were detected from this study, two of which were identified only in cancer subjects. A statistically significant association between rare hTERT-VNTR2-2 nd alleles and risk of prostate cancer was observed [OR, 5.17; 95% confidence interval (CI), 1.09-24.43; P = 0.021]. Furthermore, the results indicated that these VNTRs inserted in the enhancer region could influence the expression of hTERT in prostate cancer cell lines. This is the first study to report that rare hTERT VNTRs are associated with prostate cancer predisposition and that the VNTRs can induce enhanced levels of hTERT promoter activity in prostate cancer cell lines. Thus, the hTERT-VNTR2-2 nd locus may function as a modifier of prostate cancer risk by affecting gene expression

Diode-pumped femtosecond mode-locked Nd, Y-codoped CaF2 laser

International Nuclear Information System (INIS)

Zhu, Jiangfeng; Zhang, Lijuan; Gao, Ziye; Wang, Junli; Wang, Zhaohua; Wei, Zhiyi; Su, Liangbi; Zheng, Lihe; Wang, Jingya; Xu, Jun

2015-01-01

A passively mode-locked femtosecond laser based on an Nd, Y-codoped CaF 2 disordered crystal was demonstrated. The Y 3+ -codoping in Nd : CaF 2 markedly suppressed the quenching effect and improved the fluorescence quantum efficiency and emission spectra. With a fiber-coupled laser diode as the pump source, the continuous wave tuning range covering from 1042 to 1076 nm was realized, while the mode-locked operation generated 264 fs pulses with an average output power of 180 mW at a repetition rate of 85 MHz. The experimental results show that the Nd, Y-codoped CaF 2 disordered crystal has potential in a new generation diode-pumped high repetition rate chirped pulse amplifier. (letter)

3-D laser confocal microscopy study of the oxidation of NdFeB magnets in atmospheric conditions

Science.gov (United States)

Meakin, J. P.; Speight, J. D.; Sheridan, R. S.; Bradshaw, A.; Harris, I. R.; Williams, A. J.; Walton, A.

2016-08-01

Neodymium iron boron (NdFeB) magnets are used in a number of important applications, such as generators in gearless wind turbines, motors in electric vehicles and electronic goods (e.g.- computer hard disk drives, HDD). Hydrogen can be used as a processing gas to separate and recycle scrap sintered Nd-Fe-B magnets from end-of-life products to form a powder suitable for recycling. However, the magnets are likely to have been exposed to atmospheric conditions prior to processing, and any oxidation could lead to activation problems for the hydrogen decrepitation reaction. Many previous studies on the oxidation of NdFeB magnets have been performed at elevated temperatures; however, few studies have been formed under atmospheric conditions. In this paper a combination of 3-D laser confocal microscopy and Raman spectroscopy have been used to assess the composition, morphology and rate of oxidation/corrosion on scrap sintered NdFeB magnets. Confocal microscopy has been employed to measure the growth of surface reaction products at room temperature, immediately after exposure to air. The results showed that there was a significant height increase at the triple junctions of the Nd-rich grain boundaries. Using Raman spectroscopy, the product was shown to consist of Nd2O3 and formed only on the Nd-rich triple junctions. The diffusion coefficient of the triple junction reaction product growth at 20 °C was determined to be approximately 4 × 10-13 cm2/sec. This value is several orders of magnitude larger than values derived from the diffusion controlled oxide growth observations at elevated temperatures in the literature. This indicates that the growth of the room temperature oxidation products are likely defect enhanced processes at the NdFeB triple junctions.

Lead contamination of paint remediation workers' vehicles.

Science.gov (United States)

Boraiko, Carol; Wright, Eva M; Ralston, Faye

2013-03-01

Exposure to lead has been shown to be harmful to adults; it is a teratogen, it can damage the peripheral nervous system, and it adversely affects the reproductive system. Professional lead-based paint remediation workers are at risk of exposure to lead dust. The authors' study was conducted to determine if these remediation workers transfer lead from their work site to their vehicles and then potentially expose their families. It was hypothesized that remediation workers transported the lead from the remediation work site to the floorboards of their vehicles due to not following required protective equipment use. The laboratory's level of quantitation for lead on the wipe samples, 10 microg/ft2, was used to indicate lead contamination. This level was exceeded in 50% of the floorboards sampled. These results confirm that many vehicle floorboards used by remediation workers are contaminated with lead dust, potentially resulting in transfer of lead dust. The ultimate detrimental outcome could be the transfer of lead particles to other family members, causing the poisoning of a child or other at-risk person.

Robust H2/H∞ Control for the Electrohydraulic Steering System of a Four-Wheel Vehicle

Directory of Open Access Journals (Sweden)

Min Ye

2014-01-01

Full Text Available To shorten the steer diameter and to improve the maneuverability flexibility of a construction vehicle, four wheels’ steering system is presented. This steering system consists of mechanical-electrical-hydraulic assemblies. Its diagram and principle are depicted in detail. Then the mathematical models are derived step by step, including the whole vehicle model and the hydraulic route model. Considering the nonlinear and time-varying uncertainty of the steering system, robust H2/H∞ controller is put forward to guarantee both the system performance and the robust stability. The H∞ norm of the sensitive function from the parameter perturbation of the hydraulic system to the yaw velocity of the vehicle is taken as the evaluating index of the robustness and the H2 norm of the transfer function from the external disturbance to the steering angle of the wheel as the index of linear quadratic Gaussian. The experimental results showed that the proposed scheme was superior to classical PID controller and can guarantee both the control performance and the robustness of the steering system.

Co-doping effect of CaS and Nd2S3 nanocrystallites on luminescence properties of sol-gel SiO2 xerogel

International Nuclear Information System (INIS)

Yang, P.; Lue, M.K.; Song, C.F.; Xu, D.; Yuan, D.L.; Gu, F.

2005-01-01

The synthesis and photoluminescence characteristics of a porous phosphor silica xerogel containing CaS and Nd 2 S 3 nanoparticles entrapped in a sol-gel silica network are discussed. X-ray diffraction (XRD), transmission electron micrograph (TEM), UV-Vis absorption spectroscopy and photoluminescence spectroscopy have been performed. The observed luminescence is assigned to CaS and Nd 2 S 3 nanoparticles embedded in the sol-gel silica xerogel. Transmission electron micrographs of doped samples revealed the presence of CaS and Nd 2 S 3 nanoparticles with average diameters of 10-20 nm. Two emission bands have been observed from co-doped sample

Nd loaded liquid scintillator to search for 150Nd neutrinoless double beta decay

International Nuclear Information System (INIS)

Barabanov, I; Bezrukov, L; Yanovich, E; Cattadori, C; Danilov, N; Di Vacri, A; Ianni, A; Nisi, S; Ortica, F; Romani, A; Salvo, C; Smirnov, O

2008-01-01

The 150 Nd is considered one of the most attractive candidate for searching neutrinoless double beta (0νββ-) decay, thanks to its high Q-value (3.367 MeV), that makes the external background issue less significative respect to other isotopes, and favorable computed matrix elements. The isotopic abundance of this isotope in natural neodimium is only 5.6% and up to now, it has been investigated only in low mass experiments. The next step is to increase the sensitivity of the experiments using larger mass of neodymium (10 ton-1 kton). This could be possible with a Nd loaded liquid scintillator (LS). At the Gran Sasso National Laboratory (LNGS), a joint INFN (Istituto Nazionale di Fisica Nucleare) and INR (Institute for Nuclear Research of Moscow) working group has been carrying out since 2001 an R and D activity aiming to develop organic liquid scintillators (LS) doped with metals. The achieved know-how and the satisfactory results obtained both with In and Gd allowed to face the development and production of Nd doped LS. The development of metal doped LS is challenging because the metal has to be embedded in a proper organic system that makes it soluble in an organic solvent minimizing the impact of the metal-organic compound on the optical and scintillation properties of the LS. A further challenge in the case of Nd is the presence of absorption bands of this element in the optical region with a transparent region around 400 nm, which is about at the maximum of the scintillator emission spectrum. A 2.5 1 Nd loaded LS has been produced diluting an originally developed Nd-Carboxylic (Nd-CBX) salt in pseudocumene (PC), the solvent of the Borexino liquid scintillator. The measured light yield, at [Nd] = 6.5 g/1 and [PPO] = 1.5 g/1, is ∼ 75% of pure PC at the same fluor concentration (∼ 10000 ph/MeV). The Nd doped LS has been tested in a 2 1 quartz cell (wrapped by VM2000 reflector film) having dimensions 5x5x100 cm 3 . The light propagates in the cell by total

Fusion Technologies: 2nd Karlsruhe International Summer School

International Nuclear Information System (INIS)

Bahm, W.

2008-01-01

Nuclear fusion promises to deliver a future non-polluting energy supply with nearly unlimited fuel reserves. To win young scientists and engineers for nuclear fusion, the Karlsruhe Research Center, together with other partners in the European Fusion Education Network being established by the European Commission, organizes the 2nd Karlsruhe International Summer School on Fusion Technologies on September 1-12, 2008. The program covers all key technologies necessary for construction and operation of a fusion reactor. (orig.)

Phase transitions and molecular motions in [Ni(ND3)6](ClO4)2

International Nuclear Information System (INIS)

Migdal-Mikuli, Anna; Mikuli, Edward; Gorska, Natalia; Kowalska, Aneta; Ulanski, Jacek

2004-01-01

[Ni(ND 3 ) 6 ](ClO 4 ) 2 has three solid phases between 100 and 300 K. The phase transitions temperatures at heating (T C1 h =164.1 K and T C2 h =145.1 K) are shifted, as compared to the non-deuterated compound, towards the lower temperature of ca. 8 and 5 K, respectively. The ClO 4 - anions perform fast, picosecond, isotropic reorientation with the activation energy of 6.6 kJ mol -1 , which abruptly slow down at T C1 c phase transition, during sample cooling. The ND 3 ligands perform fast uniaxial reorientation around the Ni-N bond in all three detected phases, with the effective activation energy of 2.9 kJ mol -1 . The reorientational motion of ND 3 is only slightly distorted at the T C1 phase transition due to the dynamical orientational order-disorder process of anions. The low value of the activation energy for the ND 3 reorientation suggests that this reorientation undergoes the translation-rotation coupling, which makes the barrier to the rotation of the ammonia ligands not constant but fluctuating. The phase polymorphism and the dynamics of the molecular reorientations of the title compound are similar but not quite identical with these of the [Ni(NH 3 ) 6 ](ClO 4 ) 2

Belief Functions: Theory and Applications - Proceedings of the 2nd International Conference on Belief Functions

CERN Document Server

Masson, Marie-Hélène

2012-01-01

The theory of belief functions, also known as evidence theory or Dempster-Shafer theory, was first introduced by Arthur P. Dempster in the context of statistical inference, and was later developed by Glenn Shafer as a general framework for modeling epistemic uncertainty. These early contributions have been the starting points of many important developments, including the Transferable Belief Model and the Theory of Hints. The theory of belief functions is now well established as a general framework for reasoning with uncertainty, and has well understood connections to other frameworks such as probability, possibility and imprecise probability theories.   This volume contains the proceedings of the 2nd International Conference on Belief Functions that was held in Compiègne, France on 9-11 May 2012. It gathers 51 contributions describing recent developments both on theoretical issues (including approximation methods, combination rules, continuous belief functions, graphical models and independence concepts) an...

Soft and hard natures of Nd{sub 2}Fe{sub 14}B permanent magnet explored by first-order-reversal-curves

Energy Technology Data Exchange (ETDEWEB)

Chen, Po-An; Yang, Chao-Yao; Chang, Shu-Jui [Department of Materials Science and Engineering, National Chiao Tung University, Hsinchu, Taiwan, ROC (China); Lee, Min-Han [Undergraduate Honors Program of Nano Science and Engineering, National Chiao Tung University, Hsinchu, Taiwan, ROC (China); Tang, Nai-Kuang; Yen, Sheng-Chan [Metal Industries Research and Development Center, Kaohsiung, Taiwan (China); Tseng, Yuan-Chieh, E-mail: yctseng21@mail.nctu.edu.tw [Department of Materials Science and Engineering, National Chiao Tung University, Hsinchu, Taiwan, ROC (China)

2014-12-15

Two commercial Nd{sub 2}Fe{sub 14}B samples, MQP-B and sintered-NdFeB were investigated using synchrotron-based x-ray diffraction and first-order-reversal-curves (FORCs). Despite differing in magnetic and structural properties, the two samples were found to comprise two major ferromagnetic components in FORCs. For the sintered-NdFeB case, the soft component may originate from the intrinsically soft Nd-f site which was coupled with its local Fe atomic environment that differs in magnetic anisotropy from the Nd-g site (intrinsically hard). It may directly originate from the Nd-rich phase or microstructural imperfection, while the former possibility (Nd-f site) appears greater than the latter. While for the MQP-B, the minor second phase resulting from high structural disorder was likely in charge of the presence of the soft component. Sophisticated FORCs analyses revealed the natures of the soft and hard components, soft–hard coupling and switching reversibility of the two cases, irrespective of the origins of their two components. This provides insights to the origin of magnetic stability and reversal dynamics of Nd{sub 2}Fe{sub 14}B that have not been fully understood by conventional magnetic analyses. The coexistence of the two components led to an incoherent reversal undermining the magnetic stability of Nd{sub 2}Fe{sub 14}B. This is a fundamental problem as to why the performance extremity can only be improved finitely through extrinsic tuning. From FORCs simulation we understand that the soft–hard coupling was moderate in a real Nd{sub 2}Fe{sub 14}B compound. A stronger soft–hard coupling is necessary to conquer the anisotropic competition to enable a coherent reversal that will promote the magnetic hardness. - Highlights: • We investigated two commercially available Nd{sub 2}Fe{sub 14}B compounds with FORCs. • The two compounds were found to comprise soft and hard natures. • The coupling between the soft and hard phases is moderate in a real Nd

Analytical Modelling of Wireless Power Transfer (WPT) Systems for Electric Vehicle Application

Energy Technology Data Exchange (ETDEWEB)

Chinthavali, Madhu Sudhan [ORNL; Campbell, Steven L [ORNL

2016-01-01

This paper presents an analytical model for wireless power transfer system used in electric vehicle application. The equivalent circuit model for each major component of the system is described, including the input voltage source, resonant network, transformer, nonlinear diode rectifier load, etc. Based on the circuit model, the primary side compensation capacitance, equivalent input impedance, active / reactive power are calculated, which provides a guideline for parameter selection. Moreover, the voltage gain curve from dc output to dc input is derived as well. A hardware prototype with series-parallel resonant stage is built to verify the developed model. The experimental results from the hardware are compared with the model predicted results to show the validity of the model.

Heavy vehicle simulator (HVS) evaluation of load transfer efficiency and continuously reinforced concrete inlays on the N3 near Pietermartizburg

CSIR Research Space (South Africa)

Du Plessis, L

2006-07-01

Full Text Available The paper addresses two different heavy Vehicle Simulator (HVS) studies conducted on concrete: Load transfer through aggregate interlock and the use of dowels and the evaluation of the performance of an in-service continuously reinforced concrete...

Supercurrent transport properties in Nd substituted TlSr2CaCu2O7 high temperature superconductor

International Nuclear Information System (INIS)

Andrew Das Arulsamy; Abd Shukor, R.

1999-01-01

The transport critical current density, J ct of TI(Sr 1-x Nd x ) 2 CaCu 2 O 7 (x= 0.1, 0.2 and 0.3) high temperature superconductors were measured at various temperatures. X-ray diffraction patterns indicate that all samples consist of mainly of the 1212 phase. The variation of J ct with Nd concentration, temperature and T c were scaled using a universal function. By plotting J ct versus T n c (x) and [1-(T/T c ) 2 ] m , we can divide the temperature dependencies of J ct into two regions. In each region, a linear relationship is suggested to hold between J ct and [1-(T/T c ) 2 ] m . For x=0.1, a relatively large exponent m in the range 40 - 50 K is observed, but a lower value is observed for a higher temperature range, 55 - 60 K. Average m for x = 0. 1 in the range 40 - 70 K is 1.8 but for x=0.2 and 0.3, m is 0.6 and 1.2, respectively. This can be interpreted as an indication that there is a change in the elementary flux pinning force which is responsible for sustaining the supercurrent. A self-field approximation indicates that Nd substitution lowers the distance between pinning centers (L c ). (author)

Generation of 103 fs mode-locked pulses by a gain linewidth-variable Nd,Y:CaF2 disordered crystal.

Science.gov (United States)

Qin, Z P; Xie, G Q; Ma, J; Ge, W Y; Yuan, P; Qian, L J; Su, L B; Jiang, D P; Ma, F K; Zhang, Q; Cao, Y X; Xu, J

2014-04-01

We have demonstrated a diode-pumped passively mode-locked femtosecond Nd,Y:CaF2 disordered crystal laser for the first time to our knowledge. By choosing appropriate Y-doping concentration, a broad fluorescence linewidth of 31 nm has been obtained from the gain linewidth-variable Nd,Y:CaF2 crystal. With the Nd,Y:CaF2 disordered crystal as gain medium, the mode-locked laser generated pulses with pulse duration as short as 103 fs, average output power of 89 mW, and repetition rate of 100 MHz. To our best knowledge, this is the shortest pulse generated from Nd-doped crystal lasers so far. The research results show that the Nd,Y:CaF2 disordered crystal will be a potential alternative as gain medium of repetitive chirped pulse amplification for high-peak-power lasers.

Interaction between Nd-rich phase particles and liquid-solid interface in as-cast Ti-5Al-4Sn-2Zr-1Mo-0.25Si-1Nd titanium alloy

International Nuclear Information System (INIS)

Li, G.P.; Li, D.; Liu, Y.Y.; Hu, Z.Q.

1995-01-01

The composition (wt%) of ingot fir this investigation is 86.75%Ti, 5%Al, 4%Sn, 2%Zr, 1%Mo, 0.25%Si, 1%Nd. The alloy was prepared by vacuum arc melting in the form of buttons of mass 500 kg, which was remelted three times repeatedly to obtain homogeneous composition. The Nd-rich phase particles in the as-cast Ti-55 alloy are about 1.2∼11.07 microm and uniformly distribute in the matrix. The shapes of the particles are mainly ellipsoids together with short needle-like and blocky morphologies. The calculated diameter of the Nd-rich phase particles is ∼ 10 microm, which is within the 1.2∼11.07 microm range of the particle diameter experimentally measured in the as-cast Ti-55 alloy. The practical interface velocity is three orders of magnitude greater than V c, and the Nd-rich phase particles in the as-cast Ti-55 alloy are trapped by the liquid-solid interface

Detection of Orbital Debris Collision Risks for the Automated Transfer Vehicle

Science.gov (United States)

Peret, L.; Legendre, P.; Delavault, S.; Martin, T.

2007-01-01

In this paper, we present a general collision risk assessment method, which has been applied through numerical simulations to the Automated Transfer Vehicle (ATV) case. During ATV ascent towards the International Space Station, close approaches between the ATV and objects of the USSTRACOM catalog will be monitored through collision rosk assessment. Usually, collision risk assessment relies on an exclusion volume or a probability threshold method. Probability methods are more effective than exclusion volumes but require accurate covariance data. In this work, we propose to use a criterion defined by an adaptive exclusion area. This criterion does not require any probability calculation but is more effective than exclusion volume methods as demonstrated by our numerical experiments. The results of these studies, when confirmed and finalized, will be used for the ATV operations.

Optical spectroscopy of Nd3+/Mg2+ co-doped LiTaO3 laser crystal

International Nuclear Information System (INIS)

Zhang, P X; Hang, Y; Gong, J; Zhao, C C; Yin, J G; Zhang, L H; Zhu, Y Y

2013-01-01

A Nd 3+ and Mg 2+ co-doped LiTaO 3 single crystal has been grown successfully by the Czochralski method. The polarized absorption spectra of the crystal were measured and investigated. The peak absorption cross-sections at 806 and 810 nm were 4.17 × 10 −20 cm 2 and 4.47 × 10 −20 cm 2 with a full width at half maximum of 29 and 17 nm for σ- and π-polarization, respectively. Based on the Judd–Ofelt theory, the spectral parameters of Nd 3+ in the as-grown crystal were investigated in detail. Moreover, the emission probabilities, branching ratio and radiative lifetime for the transitions from 4 F 3/2 were calculated. The radiative lifetime of 4 F 3/2 was calculated to be 159 μs and the luminescent quantum efficiency of the 4 F 3/2 manifold was about 81.13%. The results were also compared with other Nd 3+ doped crystals. (paper)

How sustainable are 1{sup st} and 2{sup nd} generation biofuels for transportation?

Energy Technology Data Exchange (ETDEWEB)

Reinhardt, Guido; Hienz, Gunnar [ifeu-Institut fuer Energie- und Umweltforschung GmbH, Heidelberg (Germany)

2013-06-01

After the successful implementation of 1{sup st} generation biofuels in the transport sector of several countries all over the world, 2{sup nd} generation biofuels are also being produced in the meantime. Recently, there is a distinct increase in publications on the question and the concerns of many stakeholders whether these biofuels are sustainable and public awareness of this issue is prevalent. This paper summarises the state of the art of the debate whether 1{sup st} and 2{sup nd} generation biofuels are a sustainable alternative for fossil fuels for transportation. Results of several life cycle assessments are compared and conclusions are stated. An environmental assessment identifies the potentials for a sustainable development of biofuels for transportation. Conclusions are that 1{sup st} and 2{sup nd} generation biofuels show both environmental advantages and disadvantages. The analyses of energy and greenhouse gas balances show a wide range of results. Lifecycle assessments and environmental impact assessments provide a method to determine whether biofuels are environmentally sustainable. Impacts on sustainable development are exemplified in the categories land use competition, biomass use competition and CO{sub 2} avoidance costs. Not all biofuels are regarded as being advantageous from an environmental perspective. However, 1{sup st} and 2{sup nd} generation biofuels for transportation show a great potential that needs to be harmonised with other needs (e.g. land for food production or biomass use for industry and chemistry towards an overall sustainable approach). (orig.)

An automated rendezvous and capture system design concept for the cargo transfer vehicle and Space Station Freedom

Science.gov (United States)

Fuchs, Ron; Marsh, Steven

1991-01-01

A rendezvous sensor system concept was developed for the cargo transfer vehicle (CTV) to autonomously rendezvous with and be captured by Space Station Freedom (SSF). The development of requirements, the design of a unique Lockheed developed sensor concept to meet these requirements, and the system design to place this sensor on the CTV and rendezvous with the SSF are described .

The novel heavy-fermion system Nd{sub 2-x}Ce{sub x}CuO{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Pyka, N [Institut Max von Laue - Paul Langevin (ILL), 38 - Grenoble (France); Loewenhaupt, M [Technische Univ., Dresden (Germany); Metz, A [Forschungszentrum Juelich GmbH (Germany)

1997-04-01

Inelastic neutron scattering experiments are reported in the heavy fermion state of Nd{sub 2-x}Ce{sub x}CuO{sub 4}. A complex magnetic response has been observed in zero field that can be divided into contributions from correlated Nd spins (inelastic, q-dependent; reminiscent of the spin waves in Nd{sub 2}CuO{sub 4}) and from independent, slowly relaxing Nd spins (quasi-elastic, q-independent). An applied magnetic field of H > 3 Tesla gives rise to different correlations in Q - {omega} space than in zero field. Field dependent specific heat and {mu}SR experiments can be better understood in the light of these INS results. The experiments were performed on a single crystal at T {<=} 0.1 K with applied magnetic fields of H = 0 - 6 Tesla at the IN14 spectrometer. (author). 6 refs.

CW laser properties of Nd:GdYAG, Nd:LuYAG, and Nd:GdLuAG mixed crystals

Science.gov (United States)

Di, J. Q.; Xu, X. D.; Li, D. Z.; Zhou, D. H.; Wu, F.; Zhao, Z. W.; Xu, J.; Tang, D. Y.

2011-10-01

Three mixed crystals, Nd:GdYAG, Nd:LuYAG, and Nd:GdLuAG, were grown by Czochralski method. We report the continuous-wave (CW) Nd:GdYAG, Nd:LuYAG, and Nd:GdLuAG laser operation under laser diode pumping. The maximum output powers are 4.11, 5.31, and 7.47 W, with slope efficiency of 73.0, 55.3, and 57.1%, respectively. With replacing Lu3+ or Y3+ ions with large Gd3+ ions, the pump efficiency increases.

Evaluation of the induced electric field and compliance procedure for a wireless power transfer system in an electrical vehicle

International Nuclear Information System (INIS)

Laakso, Ilkka; Hirata, Akimasa

2013-01-01

In this study, an induced electric field in a human body is evaluated for the magnetic field leaked from a wireless power transfer system for charging an electrical vehicle. The magnetic field from the wireless power transfer system is modelled computationally, and its effectiveness is confirmed by comparison with the field measured in a previous study. The induced electric field in a human standing around the vehicle is smaller than the allowable limit prescribed in international guidelines, although the magnetic field strength in the human body is locally higher than the allowable external field strength. Correlation between the external magnetic field and the induced electric field is confirmed to be reasonable at least in the standing posture, which is the case discussed in the international standard. Based on this finding, we discussed and confirmed the applicability of a three-point magnetic field measurement at heights of 0.5, 1.0, and 1.5 m for safety compliance. (paper)

Evaluation of the induced electric field and compliance procedure for a wireless power transfer system in an electrical vehicle.

Science.gov (United States)

Laakso, Ilkka; Hirata, Akimasa

2013-11-07

In this study, an induced electric field in a human body is evaluated for the magnetic field leaked from a wireless power transfer system for charging an electrical vehicle. The magnetic field from the wireless power transfer system is modelled computationally, and its effectiveness is confirmed by comparison with the field measured in a previous study. The induced electric field in a human standing around the vehicle is smaller than the allowable limit prescribed in international guidelines, although the magnetic field strength in the human body is locally higher than the allowable external field strength. Correlation between the external magnetic field and the induced electric field is confirmed to be reasonable at least in the standing posture, which is the case discussed in the international standard. Based on this finding, we discussed and confirmed the applicability of a three-point magnetic field measurement at heights of 0.5, 1.0, and 1.5 m for safety compliance.

2nd Generation RLV Risk Definition Program

Science.gov (United States)

Davis, Robert M.; Stucker, Mark (Technical Monitor)

2000-01-01

The 2nd Generation RLV Risk Reduction Mid-Term Report summarizes the status of Kelly Space & Technology's activities during the first two and one half months of the program. This report was presented to the cognoscente Contracting Officer's Technical Representative (COTR) and selected Marshall Space Flight Center staff members on 26 September 2000. The report has been approved and is distributed on CD-ROM (as a PowerPoint file) in accordance with the terms of the subject contract, and contains information and data addressing the following: (1) Launch services demand and requirements; (2) Architecture, alternatives, and requirements; (3) Costs, pricing, and business cases analysis; (4) Commercial financing requirements, plans, and strategy; (5) System engineering processes and derived requirements; and (6) RLV system trade studies and design analysis.

Computer-aided topological analysis of Nd-Fe-B ternary system

International Nuclear Information System (INIS)

Liu, G.; Xu, P.; Zhang, W.

1993-01-01

A three-dimensional partially matrixed topological model of the Nd-Fe-B ternary phase diagram has been established based on experimental results assessed comprehensively with the aid of a computer-aided design and graphic and graphics software, AutoCAD (R10), and application programs developed in this work. Vertical sections at 5.88 at.% B, Nd:B = 1:1, Fe-Nd/sub 2/Fe/sub 14/B-Nd, Nd/sub 2/Fe/sub 17/-Nd/sub 2/Fe/sub 7/B/sub 6/ have been cut out from the model and the corresponding phase relationships have been analyzed. Among them, those on the Nd-rich protons of both the sections at 5.88 at.% B and Nd:B = 2:1 and those on the Nd/sub 2/Fe/sub 14/B-Nd section are given for the first time. (author)

The Effect of Grinding and Roasting Conditions on the Selective Leaching of Nd and Dy from NdFeB Magnet Scraps

Directory of Open Access Journals (Sweden)

Ho-Sung Yoon

2015-07-01

Full Text Available The pretreatment processes consisting of grinding followed by roasting were investigated to improve the selective leaching of Nd and Dy from neodymium-iron-boron (NdFeB magnet scraps. The peaks of Nd(OH3 and Fe were observed in XRD results after grinding with NaOH as the amount of water addition increased to 5 cm3. These results indicate that the components of Nd and Fe in NdFeB magnet could be changed successfully into Nd(OH3 and Fe, respectively. In the roasting tests using the ground product, with increasing roasting temperature to 500 °C, the peaks of Nd(OH3 and Fe disappeared while those of Nd2O3 and Fe2O3 were shown. The peaks of NdFeO3 in the sample roasted at 600 °C were observed in the XRD pattern. Consequently, 94.2%, 93.1%, 1.0% of Nd, Dy, Fe were leached at 400 rpm and 90 °C in 1 kmol·m−3 acetic acid solution with 1% pulp density using a sample prepared under the following conditions: 15 in stoichiometric molar ratio of NaOH:Nd, 550 rpm in rotational grinding speed, 5 cm3 in water addition, 30 min in grinding time, 400 °C and 2 h in roasting temperature and time. The results indicate that the selective leaching of Nd and Dy from NdFeB magnet could be achieved successfully by grinding and then roasting treatments.

2. slovenski MoodleMoot = 2nd Slovenian MoodleMoot

Directory of Open Access Journals (Sweden)

Viktorija Sulcic

2008-09-01

Full Text Available Moodle, an open source learning management system, is becoming widely used and recognised all over the world. Slovenian Moodle users have been participating and sharing their experience in the Moodle.si community since 2006. The initiator of the Moodle.si community – the Faculty of Management Koper organised the first Slovenian MoodleMoot Conference last year. The event was organised again in May 2008. The conference was organised by the Centre for E-Learning of the Faculty of Management Koper in co-operation with the Open Source Centre – Slovenia, Artesia and the National School for Leadership in Education. This paper presents the 2nd International Moodle.si Conference.

An animal model for Norrie disease (ND): gene targeting of the mouse ND gene.

Science.gov (United States)

Berger, W; van de Pol, D; Bächner, D; Oerlemans, F; Winkens, H; Hameister, H; Wieringa, B; Hendriks, W; Ropers, H H

1996-01-01

In order to elucidate the cellular and molecular processes which are involved in Norrie disease (ND), we have used gene targeting technology to generate ND mutant mice. The murine homologue of the ND gene was cloned and shown to encode a polypeptide that shares 94% of the amino acid sequence with its human counterpart. RNA in situ hybridization revealed expression in retina, brain and the olfactory bulb and epithelium of 2 week old mice. Hemizygous mice carrying a replacement mutation in exon 2 of the ND gene developed retrolental structures in the vitreous body and showed an overall disorganization of the retinal ganglion cell layer. The outer plexiform layer disappears occasionally, resulting in a juxtaposed inner and outer nuclear layer. At the same regions, the outer segments of the photoreceptor cell layer are no longer present. These ocular findings are consistent with observations in ND patients and the generated mouse line provides a faithful model for study of early pathogenic events in this severe X-linked recessive neurological disorder.

Anomalous magnetoelastic behaviour near morphotropic phase boundary in ferromagnetic Tb{sub 1-x}Nd{sub x}Co{sub 2} system

Energy Technology Data Exchange (ETDEWEB)

Murtaza, Adil; Yang, Sen, E-mail: yang.sen@mail.xjtu.edu.cn; Zhou, Chao; Chang, Tieyan; Chen, Kaiyun; Tian, Fanghua; Song, Xiaoping [School of Science, MOE Key Laboratory for Nonequilibrium Synthesis and Modulation of Condensed Matter, State Key Laboratory for Mechanical Behaviour of Materials, Xi' an Jiaotong University, Xi' an 710049 (China); Suchomel, Matthrew R.; Ren, Y. [X-Ray Science Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States)

2016-08-01

In this work, we report a morphotropic phase boundary (MPB) involved ferromagnetic system Tb{sub 1-x}Nd{sub x}Co{sub 2} and reveal the corresponding structural and magnetoelastic properties of this system. With high resolution synchrotron X-ray diffractometry, the crystal structure of the TbCo{sub 2}-rich side is detected to be rhombohedral and that of NdCo{sub 2}-rich side is tetragonal below their respective Curie temperatures T{sub C}. The MPB composition Tb{sub 0.35}Nd{sub 0.65}Co{sub 2} corresponds to the coexistence of the rhombohedral phase (R-phase) and tetragonal phase (T-phase). Contrary to previously reported MPB involved ferromagnetic systems, the MPB composition of Tb{sub 0.35}Nd{sub 0.65}Co{sub 2} shows minimum magnetization which can be understood as compensation of sublattice moments between the R-phase and the T-phase. Furthermore, magnetostriction of Tb{sub 1-x}Nd{sub x}Co{sub 2} decreases with increasing Nd concentration until x = 0.8 and then increases in the negative direction with further increasing Nd concentration; the optimum point for magnetoelastic properties lies towards the rhombohedral phase. Our work not only shows an anomalous type of ferromagnetic MPB but also provides an effective way to design functional materials.

Uniform magnetization reversal in dual main-phase (Ce,Nd)2Fe14B sintered magnets with inhomogeneous microstructure

International Nuclear Information System (INIS)

Zhang, Le-le; Li, Zhu-bai; Zhang, Xue-feng; Ma, Qiang; Liu, Yan-li; Li, Yong-feng; Zhao, Qian

2017-01-01

The element distribution and the magnetic properties were investigated in (Ce,Nd)–Fe–B sintered magnets prepared by mixing Nd 13.5 Fe 80 B 6.5 and Ce 9 Nd 4.5 Fe 80 B 6.5 powders with different mass ratios. Two main phases exist, but element diffusion is evident, and the chemical composition of the main phase is widely different from that of the master alloy. The Ce element tends to be expelled from the Ce-rich Re 2 Fe 14 B phase. Compared with the Ce-rich main phase, the Nd-rich Re 2 Fe 14 B phase is more stable in structure. Although the microstructure is inhomogeneous and the magnetocrystalline anisotropy is variable, the magnetization reversal is uniform in these dual main-phase magnets, which should ascribe to the existence of the exchange coupling, and magnetization reversal undergoes the nucleation of the reversed domain in irreversible magnetization. It is expected to further improve the coercivity by optimizing the distribution of the Nd-rich main phase in preparing the resource-saving (Ce,Nd) 2 Fe 14 B sintered magnets. (paper)

Enhanced broadband upconversion emission and 23 dB optical gain at 780 nm in Tm3+/Nd3+ codoped optical fiber

International Nuclear Information System (INIS)

Fan, Weiwei; Chen, Shuyue; Htein, Lin; Han, Won-Taek

2015-01-01

Maximum gain of 23 dB at 780 nm and a broadband optical gain with full width at half maximum (FWHM) of 88 nm (761–849 nm) were obtained from the Tm 3+ /Nd 3+ codoped fiber upon pumping at 1550 nm. The enhancement of the upconversion emission stretching from 730 to 970 nm was observed in the Tm 3+ /Nd 3+ codoped fiber due to the energy transfer from Tm 3+ to Nd 3+ ions. - Highlights: • We fabricated the Tm 3+ /Nd 3+ codoped silica based fiber. • The broadband upconversion emission was observed with 1550 nm pumping. • Maximum gain of 23 dB was observed at 780 nm from the Tm 3+ /Nd 3+ codoped fiber. • The gain bandwidth of the upconversion emission was largely increased due to energy transfer process

Effect of Cu addition on coercivity and interfacial state of Nd-Fe-B/Nd-rich thin films

International Nuclear Information System (INIS)

Matsuura, M; Sugimoto, S; Fukada, T; Tezuka, N; Goto, R

2010-01-01

This study provides the effect of Cu addition on coercivity (H cJ ) and interfacial microstructure in Nd-Fe-B/Nd-rich thin films. All films were deposited by using ultra high vacuum (UHV) magnetron sputtering, and the Nd-Fe-B layer was oxidized under several atmospheres with different oxygen content. Then, the films were annealed at 250-550 0 C under UHV. The films oxidized in low vacuum (10 -2 -10 -5 Pa) (under low oxygen state) exhibited the recovery of H cJ by the annealing at 450 0 C. On the contrary, the H cJ of the films oxidized in Ar (under high oxygen state) decreased with increasing annealing temperature. However, the H cJ increased drastically at the temperatures above 550 0 C. In addition, the Cu added films, which were annealed at temperatures above 350 0 C, showed higher coercivities than the films without Cu addition. The XRD analysis suggested the existence of C-Nd 2 O 3 phase in the Cu added films annealed at 550 0 C. It can be considered that the Cu addition decreases the eutectic temperature of Nd-rich phase and influences the interfacial state between Nd 2 Fe 14 B and Nd-rich phase.

Dual-Use Space Technology Transfer Conference and Exhibition. Volume 2

Science.gov (United States)

Krishen, Kumar (Compiler)

1994-01-01

This is the second volume of papers presented at the Dual-Use Space Technology Transfer Conference and Exhibition held at the Johnson Space Center February 1-3, 1994. Possible technology transfers covered during the conference were in the areas of information access; innovative microwave and optical applications; materials and structures; marketing and barriers; intelligent systems; human factors and habitation; communications and data systems; business process and technology transfer; software engineering; biotechnology and advanced bioinstrumentation; communications signal processing and analysis; medical care; applications derived from control center data systems; human performance evaluation; technology transfer methods; mathematics, modeling, and simulation; propulsion; software analysis and decision tools; systems/processes in human support technology; networks, control centers, and distributed systems; power; rapid development; perception and vision technologies; integrated vehicle health management; automation technologies; advanced avionics; and robotics technologies.

2nd Historic Mortars Conference

CERN Document Server

Hughes, John; Groot, Caspar; Historic Mortars : Characterisation, Assessment and Repair

2012-01-01

This volume focuses on research and practical issues connected with mortars on historic structures. The book is divided into four sections: Characterisation of Historic Mortars, Repair Mortars and Design Issues, Experimental Research into Properties of Repair Mortars, and Assessment and Testing. The papers present the latest work of researchers in their field. The individual contributions were selected from the contributions to the 2nd Historic Mortars Conference, which took place in Prague, September, 22-24, 2010. All papers were reviewed and improved as necessary before publication. This peer review process by the editors resulted in the 34 individual contributions included in here. One extra paper reviewing and summarising State-of-the-Art knowledge covered by this publication was added as a starting and navigational point for the reader. The editors believe that having these papers in print is important and they hope that it will stimulate further research into historic mortars and related subjects. 

Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives: Synthesis and the effects on chemical mechanical polishing (CMP) performances of sapphire wafers

Energy Technology Data Exchange (ETDEWEB)

Liu, Tingting; Lei, Hong, E-mail: hong_lei2005@aliyun.com

2017-08-15

Highlights: • The novel Nd{sup 3+}-doped colloidal SiO{sub 2} abrasives were synthesized by seed-introduced method. • The Nd{sup 3+}-doped colloidal SiO{sub 2} abrasives exhibited lower Ra and higher MRR on sapphire during CMP. • The cores SiO{sub 2} were coated by the shells (SiO{sub 2}, Nd{sub 2}Si{sub 2}O{sub 7} and Nd(OH){sub 3}) via chemical bonds and hydrogen bonds. • XPS analysis revealed the solid-state chemical reaction between Nd{sup 3+}-doped colloidal SiO{sub 2} abrasives and sapphire during CMP. - Abstract: Abrasive is one of the most important factors in chemical mechanical polishing (CMP). In order to improve the polishing qualities of sapphire substrates, the novel Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives were prepared by seed-induced growth method. In this work, there were a series of condensation reactions during the synthesis process of Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives and the silica cores were coated by shells (which contains SiO{sub 2}, Nd{sub 2}Si{sub 2}O{sub 7} and Nd(OH){sub 3}) via chemical bonds and hydrogen bonds in the Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives, which made the composite abrasives’ core-shell structure more sTable Scanning electron microscopy (SEM) showed that Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives were spherical and uniform in size. And the acting mechanisms of Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives on sapphire in CMP were investigated. Time-of-flight secondary ion mass spectroscopy (TOF-SIMS) analysis and X-ray photoelectron spectroscopy (XPS) analysis demonstrated that the solid-state chemical reactions between the shells (which contained SiO{sub 2}, Nd{sub 2}Si{sub 2}O{sub 7} and Nd(OH){sub 3}) of Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives and the sapphire occurred during the CMP process. Furthermore, Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives exhibited lower surface roughness and

Electrochemical investigations of La, Nd and Am in molten chloride salts in view of Am/Ln partitioning

International Nuclear Information System (INIS)

Pernel, C.; Serp, J.; Ougier, M.; Malmbeck, R.; Glatz, J.P.

2001-01-01

The electrochemical behaviour of La, Nd and Am has been investigated in molten LiCl-KCl eutectic. La shows a reversible single reduction/oxidation step controlled by mass transfer. The electrochemical reduction of Nd and Am proceeds via a two steps process, i.e. the reduction of trivalent species (Nd(III) and Am(III)) leading to Nd(II) and Am(II) species which are reduced at more negative potentials to form metallic deposits. Diffusion coefficients of La, Nd and Am have been calculated and are in reasonable agreement with literature data. Electro-depositions of La and Nd have been carried out onto solid Ni and liquid Cd cathodes. Much higher deposition efficiency is obtained for La compared to Nd on a solid cathode. This is an effect of the multi-valent nature of Nd in the chloride melts. (author)

Electrochemical investigations of La, Nd and Am in molten chloride salts in view of Am/Ln partitioning

Energy Technology Data Exchange (ETDEWEB)

Pernel, C.; Serp, J.; Ougier, M.; Malmbeck, R.; Glatz, J.P. [European Commission, JRC, ITU, Karlsruhe (Germany)

2001-07-01

The electrochemical behaviour of La, Nd and Am has been investigated in molten LiCl-KCl eutectic. La shows a reversible single reduction/oxidation step controlled by mass transfer. The electrochemical reduction of Nd and Am proceeds via a two steps process, i.e. the reduction of trivalent species (Nd(III) and Am(III)) leading to Nd(II) and Am(II) species which are reduced at more negative potentials to form metallic deposits. Diffusion coefficients of La, Nd and Am have been calculated and are in reasonable agreement with literature data. Electro-depositions of La and Nd have been carried out onto solid Ni and liquid Cd cathodes. Much higher deposition efficiency is obtained for La compared to Nd on a solid cathode. This is an effect of the multi-valent nature of Nd in the chloride melts. (author)

Anomalous behavior of spin fluctuations in polycrystalline NdBa_2Cu_3O_7-δ

Science.gov (United States)

Abdelrazek, M. M.; Reyes, A. P.; Kuhns, P. L.; Moulton, W. G.; Halperin, W. P.; Kishio, K.

2001-03-01

Critical slowing down of Nd spin fluctuations have been observed in 92K superconductor NdBa_2Cu_3O_7-δ at temperatures well below Tc and orders of magnitude higher than TN ( ~0.5K). Nuclear spin-lattice relaxation rate 1/T1 at the planar O(2,3) and bridging O(4) oxygen sites have been measured as a function of temperature in fields up to 37T. Data is characterized by an extremely fast relaxation, roughly two orders of magnitude larger than those of YBCO, suggestive of Nd origin. The temperature dependence shows neither Tc nor the pseudo-gap but rather a well-defined field-dependent peak for both sites. Preliminary analysis suggests 1/T1 follows the typical behavior of freezing of spin fluctuations, when the inverse correlation time of the Nd spins τc becomes comparable to NMR frequency, ω τc ~ 1. The field dependence originates from the tail of the power spectrum beyond the 1/τc cutoff. The implications of these results to superconductivity in these systems will be discussed.

Intergenerational Transmission and the School-to-work Transition for 2nd Generation Immigrants

DEFF Research Database (Denmark)

Nielsen, Helena Skyt; Rosholm, Michael; Smith, Nina

2001-01-01

We analyse the extent of intergenerational transmission through parental capital, ethnic capital and neighbourhood effects on several aspects of the school-to-work transition of 2nd generation immigrants and young ethnic Danes. The main findings are that parental capital has strong positive effects...... on the probability of completing a qualifying education and on the entry into the labour market, but it has a much smaller impact on the duration of the first employment spell and on the wage level. Growing up in neighbourhoods with a high concentration of immigrants is associated with negative labour market...... prospects both for young natives and 2nd generation immigrants....

Growth and characterization of Nd-doped disordered Ca3Gd2(BO3)4 crystal

Science.gov (United States)

Pan, Z. B.; Zhang, H. J.; Yu, H. H.; Xu, M.; Zhang, Y. Y.; Sun, S. Q.; Wang, J. Y.; Wang, Q.; Wei, Z. Y.; Zhang, Z. G.

2012-01-01

A high-quality disordered Nd3+:Ca3Gd2(BO3)4 (Nd3+:CGB) laser crystal was grown by the Czochralski method. The space group and effective segregation coefficient of Nd3+ were determined to be Pnma and 1.06, respectively. The thermal properties, including the average linear thermal expansion coefficient, thermal diffusivity, specific heat, and thermal conductivity were systematically measured for the first time. It was found that the thermal conductivity increases with increasing temperature, indicating glasslike behavior. The polarized spectral properties of the crystal were investigated, including the polarized absorption spectra, polarized fluorescence spectra, and fluorescence decay. The spectroscopic parameters of Nd3+ ions in Nd3+:CGB crystal have been obtained based on Judd-Ofelt theory. The anisotropy of the spectral properties for different polarized directions was discussed. Additionally, the continuous-wave (CW) laser performance at 1.06 μm was demonstrated for the first time. The maximum output power of 603 mW was achieved with corresponding optical conversion efficiency of 8.33% and slope efficiency of 9.95%.

Potential vehicle fleet CO2 reductions and cost implications for various vehicle technology deployment scenarios in Europe

International Nuclear Information System (INIS)

Pasaoglu, Guzay; Honselaar, Michel; Thiel, Christian

2012-01-01

The continuous rise in demand for road transportation has a significant effect on Europe's oil dependency and emissions of greenhouse gases. Alternative fuels and vehicle technology can mitigate these effects. This study analyses power-train deployment scenarios for passenger cars and light commercial vehicles in EU-27 until 2050. It considers European policy developments on vehicle CO 2 emissions, bio-energy mandates and reductions in the CO 2 footprint of the European energy mix and translates these into comprehensive scenarios for the road transport sector. It quantifies and assesses the potential impact of these scenarios on well-to-wheel (WtW) CO 2 emission reductions primary energy demand evolution, and cost aspects for the prospective vehicle owners. The study reveals that, under the deployed scenarios, the use of bio-fuel blends, technological learning and the deployment of hybrids, battery electric, plug-in hybrid and fuel cell vehicles can decrease WtW CO 2 emissions in EU-27 passenger road transport by 35–57% (compared to 2010 levels) and primary energy demand by 29–51 Mtoe as they would benefit from a future assumed decarbonised electricity and hydrogen mix in Europe. Learning effects can lead to acceptable payback periods for vehicle owners of electric drive vehicles. - Highlights: ► Power-train penetration scenarios for 2010–2050 passenger road transport in Europe. ► A dedicated tool is developed to analyse H 2 production and distribution mix till 2050. ► Alternative vehicles can drastically reduce CO 2 emissions and energy demand. ► Electric vehicles could become cost competitive to conventional vehicles by 2030. ► Policies needed to create adequate momentum and guarantee decarbonised transport.

Wireless IR Image Transfer System for Autonomous Vehicles

Science.gov (United States)

2003-12-01

the camera can operate between 0 and 500 C; this uniquely suites it for employment on autonomous vehicles in rugged environments. The camera is...system is suitable for used on autonomous vehicles under varying antenna orientations. • The third is the use of MDS transceivers allows the received

2nd Applied Electromagnetic International Conference

CERN Document Server

Sulaiman, Hamzah; Othman, Mohd; Aziz, Mohamad; Malek, Mohd

2017-01-01

In this book, experts from academia and industry present the latest advances in scientific theory relating to applied electromagnetics and examine current and emerging applications particularly within the fields of electronics, communications, and computer technology. The book is based on presentations delivered at APPEIC 2015, the 2nd Applied Electromagnetic International Conference, held in Krabi, Thailand in December 2015. The conference provided an ideal platform for researchers and specialists to deliver both theoretically and practically oriented contributions on a wide range of topics relevant to the theme of nurturing applied electromagnetics for human technology. Many novel aspects were addressed, and the contributions selected for this book highlight the relevance of advances in applied electromagnetics to a variety of industrial engineering problems and identify exciting future directions for research.

Tannic acid alleviates bulk and nanoparticle Nd2O3 toxicity in pumpkin: a physiological and molecular response.

Science.gov (United States)

Chen, Guangcai; Ma, Chuanxin; Mukherjee, Arnab; Musante, Craig; Zhang, Jianfeng; White, Jason C; Dhankher, Om Parkash; Xing, Baoshan

2016-11-01

The effect of dissolved organic matter (DOM) on nanoparticle toxicity to plants is poorly understood. In this study, tannic acid (TA) was selected as a DOM surrogate to explore the mechanisms of neodymium oxide NPs (Nd2O3 NPs) phytotoxicity to pumpkin (Cucurbita maxima). The results from the tested concentrations showed that 100 mg L(-1) Nd2O3 NPs were significantly toxic to pumpkin in term of fresh biomass, and the similar results from the bulk particles and the ionic treatments were also evident. Exposure to 100 mg L(-1) of Nd2O3 NPs and BPs in 1/5 strength Hoagland's solution not only significantly inhibited pumpkin growth, but also decreased the S, Ca, K and Mg levels in plant tissues. However, 60 mg L(-1) TA significantly moderated the observed phytotoxicity, decreased Nd accumulation in the roots, and notably restored S, Ca, K and Mg levels in NPs and BPs treated pumpkin. TA at 60 mg L(-1) increased superoxide dismutase (SOD) activity in both roots (17.5%) and leaves (42.9%), and catalase (CAT) activity (243.1%) in the roots exposed to Nd2O3 NPs. This finding was confirmed by the observed up-regulation of transcript levels of SOD and CAT in Nd2O3 NPs treated pumpkin analyzed by quantitative reverse transcription polymerase chain reaction. These results suggest that TA alleviates Nd2O3 BPs/NPs toxicity through alteration of the particle surface charge, thus reducing the contact and uptake of NPs by pumpkin. In addition, TA promotes antioxidant enzymatic activity by elevating the transcript levels of genes involved in ROS scavenging. Our results shed light on the mechanisms underlying the influence of DOM on the bioavailability and toxicity of NPs to terrestrial plants.

Surface modification of nanodiamond through metal free atom transfer radical polymerization

Science.gov (United States)

Zeng, Guangjian; Liu, Meiying; Shi, Kexin; Heng, Chunning; Mao, Liucheng; Wan, Qing; Huang, Hongye; Deng, Fengjie; Zhang, Xiaoyong; Wei, Yen

2016-12-01

Surface modification of nanodiamond (ND) with poly(2-methacryloyloxyethyl phosphorylcholine) [poly(MPC)] has been achieved by using metal free surface initiated atom transfer radical polymerization (SI-ATRP). The ATRP initiator was first immobilized on the surface of ND through direct esterification reaction between hydroxyl group of ND and 2-bromoisobutyryl bromide. The initiator could be employed to obtain ND-poly(MPC) nanocomposites through SI-ATRP using an organic catalyst. The final functional materials were characterized by 1H nuclear magnetic resonance, transmission electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and thermo gravimetric analysis in detailed. All of these characterization results demonstrated that ND-poly(MPC) have been successfully obtained via metal free photo-initiated SI-ATRP. The ND-poly(MPC) nanocomposites shown enhanced dispersibility in various solvents as well as excellent biocompatibility. As compared with traditional ATRP, the metal free ATRP is rather simple and effective. More importantly, this preparation method avoided the negative influence of metal catalysts. Therefore, the method described in this work should be a promising strategy for fabrication of polymeric nanocomposites with great potential for different applications especially in biomedical fields.

Influence of radius of cylinder HTS bulk on guidance force in a maglev vehicle system

Science.gov (United States)

Longcai, Zhang

2014-07-01

Bulk superconductors had great potential for various engineering applications, especially in a high-temperature superconducting (HTS) maglev vehicle system. In such a system, the HTS bulks were always exposed to AC external magnetic field, which was generated by the inhomogeneous surface magnetic field of the NdFeB guideway. In our previous work, it was observed that the guidance force of the YBCO bulk over the NdFeB guideway used in the HTS maglev vehicle system was decayed by the application of the AC external magnetic field. In this paper, we investigated the influence of the radius of the cylinder HTS bulk exposed to an AC magnetic field perturbation on the guidance force in the maglev vehicle system. From the results, it was found that the guidance force was stronger for the bulk with bigger radius and the guidance force decay rates of the bulks were approximately equal despite of the different radius in the maglev vehicle system. Therefore, in order to obtain higher guidance force in the maglev vehicle system, we could use the cylinder HTS bulks with the bigger radius.

Phase stability and oxygen diffusion in RBa2Cu3O6+x (R=Y, Nd)

International Nuclear Information System (INIS)

Mozhaev, A.P.; Mazo, G.N.; Galkin, A.A.; Khromova, N.V.

1996-01-01

Phase stability boundaries of RBa 2 Cu 3 O 6 + x (R=Y, Nd) compounds for oxygen partial pressure wide range were determined by means of Coulomb titration. Phase decomposition is shown to occur without formation of liquid phase. Principial differences in the chemical composition of decomposition product of Y- and Nd-containing phases were detected. Dependences of oxygen non-stoichiometry of the compounds on temperature were determined. Fragments of P o 2 -T-x-diagrams were plotted. Oxygen diffusion coefficients within wide range of temperatures and partial pressures of oxygen were determined. Dependence of diffusion parameters on oxygen non-stoichiometry and P o 2 was determined. Oxygen diffusion was determined to occur more rapidly in orthorhombic phase than in tetragonal one. Diffusion coefficients were shown to increase at transition from Y-to Nd-containing phase. 13 refs., 6 figs., 2 tabs

Formation of defect-fluorite structured NdNiOxHy epitaxial thin films via a soft chemical route from NdNiO3 precursors.

Science.gov (United States)

Onozuka, T; Chikamatsu, A; Katayama, T; Fukumura, T; Hasegawa, T

2016-07-26

A new phase of oxyhydride NdNiOxHy with a defect-fluorite structure was obtained by a soft chemical reaction of NdNiO3 epitaxial thin films on a substrate of SrTiO3 (100) with CaH2. The epitaxial relationship of this phase relative to SrTiO3 could be controlled by changing the reaction temperature. At 240 °C, NdNiOxHy grew with a [001] orientation, forming a thin layer of infinite-layer NdNiO2 at the interface between the NdNiOxHy and the substrate. Meanwhile, a high-temperature reaction at 400 °C formed [110]-oriented NdNiOxHy without NdNiO2.

LD pumped Nd: YLF amplification technology

International Nuclear Information System (INIS)

Qin Xingwu; Li Mingzhong; Luo Yiming; Sui Zhan; Ding Lei; Liang Yue; Zhao Runchang; Chen Lianming

2003-01-01

A Ring-LD-pumped Nd: YLF laser amplifier system is theoretically and experimentally discussed. A structure of off-axes double passes amplifier is used. The results of experiment shown that 109 mJ output energy with a net gain of 1115 is obtained under 150 μJ input energy; a compact side-pumped structure is used to obtain a high transferring efficiency of LD array, 1.01 J output energy is achieved at 1053 nm. (authors)

Influence of Nd-Doping on Photocatalytic Properties of TiO2 Nanoparticles and Thin Film Coatings

Directory of Open Access Journals (Sweden)

Damian Wojcieszak

2014-01-01

Full Text Available Structural, optical, and photocatalytic properties of TiO2 and TiO2:Nd nanopowders and thin films composed of those materials have been compared. Titania nanoparticles with 1, 3, and 6 at. % of Nd-dopant were synthesized by sol-gel method. Additionally, thin films with the same material composition were prepared with the aid of spin-coating method. The analysis of structural investigations revealed that all as-prepared nanopowders were nanocrystalline and had TiO2-anatase structure. The average size of crystallites was ca. 4-5 nm and the correlation between the amount of neodymium and the size of TiO2 crystallites was observed. It was shown that the dopant content influenced the agglomeration of the nanoparticles. The results of photocatalytic decomposition of MO showed that doping with Nd (especially in the amount of 3 at. % increased self-cleaning activity of the prepared titania nanopowder. Similar effect was received in case of the thin films, but the decomposition rate was lower due to their smaller active surface area. However, the as-prepared TiO2:Nd photocatalyst in the form of thin films or nanopowders seems to be a very attractive material for various applications.

Microstructural investigation of RBa/sub 2/Cu/sub 3/O/sub 7/-delta (R=Y, Gd, Nd)

Energy Technology Data Exchange (ETDEWEB)

Parent, L; Moreau, C; Noel, D; Dallaire, S; Champagne, B

1989-01-01

RBa/sub 2/Cu/sub 3/O/sub 7-delta/ perovskites, where R is Y, Gd and Nd, were synthetized using the same experimental conditions. The resistivity curves of the three compounds were similar but their microstructures were different. Secondary phases (CuO, BaCuO/sub 2/) were formed in the compounds containing Y and Gd while no such phases were detected in the Nd perovskite material. According to these preliminary results, the perovskite containing Nd is readily synthesized since the amount of secondary phases is much lower in that case. 7 refs., 4 figs., 1 tab.

The Clean Development Mechanism as a Vehicle for Technology Transfer and Sustainable Development - Myth or Reality?

Directory of Open Access Journals (Sweden)

Gary Cox

2010-09-01

Full Text Available This paper critically examines the clean development mechanism (CDM established under Article 12 of the Kyoto Protocol in terms of its effectiveness as a vehicle for technology transfer to developing countries, a specific commitment under the UNFCCC. Fundamentally, the paper poses the question of whether technology transfer as part of the CDM is a myth or a reality in the broader context of sustainable development. Technology transfer between countries of the North and South is explored in a historical context and the emergence of technology transfer obligations is traced in multilateral environmental agreements. The architecture of the UNFCCC and the Kyoto Protocol are examined in relation to technology transfer obligations. Empirical studies are reviewed to gain an understanding of how CDM operates in practice, with a closer examination of a small number of recent CDM projects. There is an update on the Technology Mechanism being established under the Copenhagen Accord. The paper concludes with a summary of the benefits of CDM to date and its current limitations in achieving the scaling-up of affordable environmentally sound technology transfer envisaged in the Bali Action Plan. The conclusion is that technology transfer must be a much more explicit objective of CDM with better targeting of projects in order to achieve locally sustainable equitable outcomes. Furthermore, the link between CDM and technology transfer needs to be much more explicitly made in order that, in the long run, such interventions will lead to viable low emission development pathways in developing countries.

Effects of Nd:YAG and CO2 lasers on cerebral microvasculature. Study in normal rabbit brain.

Science.gov (United States)

Kuroiwa, T; Tsuyumu, M; Takei, H; Inaba, Y

1986-01-01

The effect of Nd:YAG and CO2 laser beams on cerebral microvasculature was examined in experimental animals. Soft x-ray microangiography and histological examination of the brain after Nd:YAG laser exposure revealed broad avascular or oligovascular zones in the irradiated and the surrounding edematous tissue, in which the surviving vessels were narrowed and tapered without significant leakage of blood. After CO2 laser exposure, a wedge-shaped tissue defect surrounded by layers of charring, coagulation, and edema was observed. The main finding in the surrounding coagulation and edematous layers was dilatation of the vessels. Hemorrhage was sometimes observed, mainly in the edematous layer. These findings seem to explain the effective hemostatic capability of the Nd:YAG laser and the occasional hemorrhage following CO2 laser exposure, especially at high energy output.

Micromagnetic finite element study for magnetic properties of nanocomposite exchange coupled Nd{sub 2}Fe{sub 14}B/α-Fe multilayer systems

Energy Technology Data Exchange (ETDEWEB)

Ryo, Hyok-Su [School of Material Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Faculty of Physics, Kim Il Sung University, Pyongyang 999093, Democratic People’s Republic of Korea (Korea, Republic of); Hu, Lian-Xi [School of Material Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Kim, Jin-Guk [School of Material Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Faculty of Physics, Kim Il Sung University, Pyongyang 999093, Democratic People’s Republic of Korea (Korea, Republic of); Yang, Yu-Lin [School of Chemistry and Chemical Engineering, Harbin Institute of Technology, Harbin 150001 (China)

2017-03-15

In this study, magnetic properties of exchange coupled nanocomposite multilayer thin films constructed alternately with magnetic hard Nd{sub 2}Fe{sub 14}B layers and soft α-Fe layers have been studied by micromagnetic finite element method (FEM). According to the results, effects of the thicknesses of layers and the magneto-crystalline anisotropy on the magnetic properties of the Nd{sub 2}Fe{sub 14}B/α-Fe multilayer systems have been estimated. On the other hand, the results have been analyzed by means of efficiency of interphase exchange coupling, which can be estimated by volume ratios of exchange coupled areas between magnetically hard Nd{sub 2}Fe{sub 14}B and soft α-Fe phase layers. The results show that the magnetic properties of exchange coupled Nd{sub 2}Fe{sub 14}B/α-Fe multilayer systems can be enhanced by efficient interphase exchange coupling between magnetically hard Nd{sub 2}Fe{sub 14}B layers and soft α-Fe layers. - Highlights: • Phase layer thicknesses dependence of magnetic properties of Nd{sub 2}Fe{sub 14}B/α-Fe multilayers. • Analyzation of the effectiveness of exchange coupling between the Nd{sub 2}Fe{sub 14}B and α-Fe layers. • Dependence of the magnetic properties on direction of external field of exchange coupled Nd{sub 2}Fe{sub 14}B/α-Fe multilayers. • Dependence of the magnetic properties on magneto-crystalline anisotropy of exchange coupled Nd{sub 2}Fe{sub 14}B/α-Fe multilayers.

[Employment and education in the 2nd economic and social development plan of Togo].

Science.gov (United States)

Dovi-sodemekou, F B

1985-01-01

Togo is a developing country whose population is increasing at the rapid rate of 2.7%/year. Economic development is therefore a necessity to ensure at least an average standard of living. Plans of development include objectives of structural societal changes, including improvements in education and employment. This study analyzes the evolution of population activities. It identifies obstacles to the improvement of education and employment. The investigation examines the employment and education situation before adoption of the 2nd plan of Togo and predicts the probable evolution of the situation. Despite the priority accorded to agriculture, the 2nd plan appears to give greater importance to industry. The industrial and commercial sector has witnessed a 65.2% investment increase, whereas the rural sector had an investment increase of 11.8%. The 2nd plan, in view of its relation to the evolution of economic activities, took into account the demand for manual labor. In the private sector, industries should occupy an important position. The dualism of a modern and a traditional sector is considered a cause of underdevelopment. The modern sector should be developed in order to suppress the traditional sector and allow progress in society. As a result of this approach, agriculture is given a 2ndary role.

Electronic properties of Nd2−xCexCuO4+δ: A hard X-ray photoemission investigation

International Nuclear Information System (INIS)

Guarino, A.; Panaccione, G.; Offi, F.; Monaco, G.; Fondacaro, A.; Torelli, P.; Fittipaldi, R.; Vecchione, A.; Pace, S.; Nigro, A.

2016-01-01

Highlights: • We grow and characterize Nd 2−x Ce x CuO 4+δ samples as thin film and single crystal. • We study the Cu 2p levels of our samples by hard X-ray photoemission spectroscopy. • We investigate bulk features of the Nd 2−x Ce x CuO 4+δ samples. • Signature of the bulk response is correlated with the crystallinity of the samples. - Abstract: Cu 2p core levels spectra measured by X-ray photoemission spectroscopy of selected as-grown Nd 2−x Ce x CuO 4+δ samples are presented and discussed. The presence of a satellite peak in the 2p core level of Nd 2−x Ce x CuO 4+δ single crystal by hard X-ray photoemission is confirmed in all non-superconducting samples, films and single crystals investigated in this work. The comparison of the spectral features of the different samples suggests that the presence and the intensity of this satellite peak is not related to the electric transport properties, but to the texture characteristics.

Photocatalytic characteristics for the nanocrystalline TiO{sub 2} on the Ag-doped CaAl{sub 2}O{sub 4}:(Eu,Nd) phosphor

Energy Technology Data Exchange (ETDEWEB)

Kim, Jung-Sik, E-mail: jskim@uos.ac.kr; Sung, Hyun-Je; Kim, Bum-Joon

2015-04-15

Highlights: • The photocatalytic reactivity of the TiO{sub 2}-coated on the Ag-doped long-lasting phosphor (CaAl{sub 2}O{sub 4}:Eu{sup 2+},Nd{sup 3+}). • The photodecomposition of benzene gas under visible light irradiation. • The TiO{sub 2}-coated on the Ag-doped long-lasting phosphor showed much higher photocatalytic reactivity. • The light emitted from the long-lasting phosphors contributed to the photo generation of TiO{sub 2}. - Abstract: This study investigated the photocatalytic behavior of nanocrystalline TiO{sub 2} deposited on Ag-doped long-lasting phosphor (CaAl{sub 2}O{sub 4}:Eu{sup 2+},Nd{sup 3+}). The CaAl{sub 2}O{sub 4}:Eu{sup 2+},Nd{sup 3+} phosphor powders were prepared via conventional sintering using CaCO{sub 3}, Al{sub 2}O{sub 3}, Eu{sub 2}O{sub 3}, and Nd{sub 2}O{sub 3} as raw materials according to the appropriate molar ratios. Silver nanoparticles were loaded on the phosphor by mixing with an aqueous Ag-dispersion solution. Nanocrystalline TiO{sub 2} was deposited on Ag-doped CaAl{sub 2}O{sub 4}:Eu{sup 2+},Nd{sup 3+} powders via low-pressure chemical vapor deposition (LPCVD). The TiO{sub 2} coated on the phosphor was actively photo-reactive under irradiation with visible light and showed much faster benzene degradation than pure TiO{sub 2}, which is almost non-reactive. The coupling of TiO{sub 2} with phosphor may result in an energy band bending in the junction region, which then induces the TiO{sub 2} crystal at the interface to be photo-reactive under irradiation with visible light. In addition, the intermetallic compound of CaTiO{sub 3} that formed at the interface between TiO{sub 2} and the CaAl{sub 2}O{sub 4}:(Eu{sup 2+},Nd{sup 3+}) phosphor results in the formation of oxygen vacancies and additional electrons that promote the photodecomposition of benzene gas. The addition of Ag nanoparticles enhanced the photocatalytic reactivity of the TiO{sub 2}/CaAl{sub 2}O{sub 4}:Eu{sup 2+},Nd{sup 3+} phosphor. TiO{sub 2} on the Ag

Structure and magnetic properties of hot deformed Nd2Fe14B magnets doped with DyHx nanoparticles

Science.gov (United States)

Wang, C. G.; Yue, M.; Zhang, D. T.; Liu, W. Q.; Zhang, J. X.

2016-04-01

Commercial NdFeB powders mixed with DyHx nanoparticles are hot pressed and hot deformed into anisotropic magnets by Spark Plasma Sintering (SPS). The hot deformed magnet exhibits strong c-axis crystallographic texture. The coercivity of the magnet doped with 1.0 wt% DyHx is increased by 66.7%, compared with the magnet without DyHx, while the remanence decreases only by 3%. TEM observation shows that there exists a continuous (Nd,Dy)2Fe14B layer between Nd-rich phase and NdFeB main phase.

Effects of thickness and annealing condition on magnetic properties and thermal stabilities of Ta/Nd/NdFeB/Nd/Ta sandwiched films

International Nuclear Information System (INIS)

Liu Wen-Feng; Zhang Min-Gang; Zhang Ke-Wei; Zhang Hai-Jie; Chai Yue-Sheng; Xu Xiao-Hong

2016-01-01

Ta/Nd/NdFeB/Nd/Ta sandwiched films are deposited by magnetron sputtering on Si (100) substrates, and subsequently annealed in vacuum at different temperatures for different time. It is found that both the thickness of NdFeB and Nd layer and the annealing condition can affect the magnetic properties of Ta/Nd/NdFeB/Nd/Ta films. Interestingly, the thickness and annealing temperature show the relevant behaviors that can affect the magnetic properties of the film. The high coercivity of 24.1 kOe (1 Oe = 79.5775 A/m) and remanence ratio (remanent magnetization/saturation magnetization) of 0.94 can be obtained in a Ta/Nd(250 nm)/NdFeB(600 nm)/Nd(250 nm)/Ta film annealed for 3 min at 1023 K. In addition, the thermal stability of the film is also linked to the thickness of NdFeB and Nd layer and the annealing temperature as well. The excellent thermal stability can be achieved in a Ta/Nd(250 nm)/NdFeB(600 nm)/Nd(250 nm)/Ta film annealed at 1023 K. (paper)

Phase evolution and aqueous durability of Zr{sub 1−x−y}Ce{sub x}Nd{sub y}O{sub 2−y/2} ceramics designed to immobilize actinides with multi-valences

Energy Technology Data Exchange (ETDEWEB)

Ding, Yi, E-mail: dingyi2279@126.com [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang, Sichuan, 621900 (China); Key Subject Laboratory of National Defense for Radioactive Waste and Environmental Security, Southwest University of Science and Technology, Mianyang 621010 (China); Long, Xinggui, E-mail: xingguil@caep.cn [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang, Sichuan, 621900 (China); Peng, Shuming [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang, Sichuan, 621900 (China); Zhang, Dong, E-mail: zd0823@sina.com [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang, Sichuan, 621900 (China); Tan, Zhaoyi [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang, Sichuan, 621900 (China); Lu, Xirui [Key Subject Laboratory of National Defense for Radioactive Waste and Environmental Security, Southwest University of Science and Technology, Mianyang 621010 (China)

2017-04-15

Zr{sub 1−x−y}Ce{sub x}Nd{sub y}O{sub 2−y/2} ceramics, which were designed as waste form materials, were obtained by simultaneous substitution of Ce{sup 4+} and Nd{sup 3+} for Zr{sup 4+} in ZrO{sub 2}. The influences of the simultaneous substitution of Ce and Nd on phase transformation of ZrO{sub 2} were investigated systematically. Also, the aqueous durability of the ceramics was evaluated. The results show that the phase transformation caused by the simultaneous substitution mainly relates to the total content of Ce and Nd. The ZrO{sub 2} ceramics containing Ce + Nd < 30 mol% exhibit both monoclinic and cubic phases, while the ceramics containing Ce + Nd ≥ 30 mol% are cubic phase. And the cubic phase can be stabilized by incorporating 30 mol% Ce + Nd. Moreover, LR{sub i} are modified by the incorporation of Ce and Nd, because of the presence of oxygen vacancies. The Nd and Ce co-doped zirconia waste form exhibit excellent aqueous durability (∼10{sup −5} g m{sup −2} d{sup −1}). - Highlights: •Zr{sub 1−x−y}Ce{sub x}Nd{sub y}O{sub 2−y/2} were obtained by substitution of Ce and Nd for Zr in ZrO{sub 2}. •Phase transformation mainly relates to the total content of Ce and Nd. •Samples with Ce + Nd < 30 mol% show monoclinic and cubic phases, while ≥30 mol% are cubic. •Stabilized cubic zirconia can be obtained by doping with 30 mol% Ce and Nd. •LR{sub Ce} and LR{sub Nd} (42 d) are ∼ 10{sup −5} g m{sup −2} d{sup −1}, exhibiting excellent aqueous durability.

Battery control system for hybrid vehicle and method for controlling a hybrid vehicle battery

Science.gov (United States)

Bockelmann, Thomas R [Battle Creek, MI; Hope, Mark E [Marshall, MI; Zou, Zhanjiang [Battle Creek, MI; Kang, Xiaosong [Battle Creek, MI

2009-02-10

A battery control system for hybrid vehicle includes a hybrid powertrain battery, a vehicle accessory battery, and a prime mover driven generator adapted to charge the vehicle accessory battery. A detecting arrangement is configured to monitor the vehicle accessory battery's state of charge. A controller is configured to activate the prime mover to drive the generator and recharge the vehicle accessory battery in response to the vehicle accessory battery's state of charge falling below a first predetermined level, or transfer electrical power from the hybrid powertrain battery to the vehicle accessory battery in response to the vehicle accessory battery's state of charge falling below a second predetermined level. The invention further includes a method for controlling a hybrid vehicle powertrain system.

Study on magnetic properties of (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B (x = 0–0.6) alloys

Energy Technology Data Exchange (ETDEWEB)

Tan, G.S.; Xu, H., E-mail: huixu8888@shu.edu.cn; Yu, L.Y.; Tan, X.H.; Zhang, Q.; Gu, Y.; Hou, X.L.

2017-09-01

Highlights: • (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B alloys are prepared by melt-spinning method with simultaneously decreasing of Nd, Ce concentration. • The magnetic properties B{sub r}, (BH){sub max} and squareness are all improved with an appropriate reduction of Nd, Ce concentration. • Magnetic field heat treatment offers a significant improvement in B{sub r}, (BH){sub max} and squareness. - Abstract: In the present work, (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B (x = 0–0.6) permanent alloys are prepared by melt-spinning method. The hard magnetic properties of (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B (x = 0–0.6) alloys annealed at optimum temperatures have been investigated systematically. Depending on the Nd, Ce concentration, the maximum energy product ((BH){sub max}) and remanence (B{sub r}) increase gradually with x in the range of 0 ≤ x ≤ 0.4, whereas decrease gradually in the alloys with 0.4 < x ≤ 0.6. It is found that the optimum magnetic properties are obtained at x = 0.4: H{sub ci} = 4.9 kOe, B{sub r} = 10.1 kG, (BH){sub max} = 13.7 MGOe. Specifically, magnetic field heat treatment below the Curie temperature is applied for (Nd{sub 0.8}Ce{sub 0.2}){sub 1.6}Fe{sub 12}Co{sub 2}B (x = 0.4) annealed ribbons. The magnetic properties B{sub r}, (BH){sub max} and squareness are all enhanced after the magnetic field heat treatment. The (BH){sub max} shows a substantial increase from 13.7 MGOe to 16.0 MGOe after the heat treatment at 623 K with a magnetic field of 1 T, which gets 17% improvement compared with that of the sample without a magnetic field heat treatment. We demonstrate that the magnetic field heat treatment plays a certain role in the magnetization reversal behavior and can improve the microstructure of (Nd{sub 0.8}Ce{sub 0.2}){sub 1.6}Fe{sub 12}Co{sub 2}B alloy.

Remote operated vehicle with carbon dioxide blasting (ROVCO2)

International Nuclear Information System (INIS)

Resnick, A.M.

1995-01-01

The Remote Operated Vehicle with Carbon Dioxide Blasting (ROVCO 2 ), as shown in a front view, is a six-wheeled remote land vehicle used to decontaminate concrete floors. The remote vehicle has a high pressure Cryogenesis blasting subsystem, Oceaneering Technologies (OTECH) developed a CO 2 xY Orthogonal Translational End Effector (COYOTEE) subsystem, and a vacuum/filtration and containment subsystem. Figure 2 shows a block diagram with the various subsystems labeled

Magnetic Properties and Magnetocaloric Effect in Layered NdMn1.9Ti0.1Si2

Directory of Open Access Journals (Sweden)

M.F. Md Din

2014-04-01

Full Text Available The structural and magnetic properties of the NdMn1.9Ti0.1Si2 compund have been studied by high-intensity x-ray and high-resolution neutron powder diffraction, specific heat, dc magnetization, and differential scanning calorimetry measurements over the temperature range of 3-450 K. The Curie temperature and Néel temperature of layered NdMn1.9Ti0.1Si2 are indicated as TC ~ 22 K and TN ~ 374 K respectively. The first order magnetic transition from antiferromagnetic [AFil-type] to ferromagnetic [F(Nd+Fmc] around TC is found in layered NdMn1.9Ti0.1Si2 and is associated with large magnetocaloric effect. This behavior has been confirmed as a contribution of the magnetostructural coupling by using neutron and x-ray powder diffraction. The magnetic entropy change –ΔSM ~ 15.3 J kg-1 K-1 and adiabatic temperature change ΔTad ~ 4.7 K have been determined using magnetization and specific heat measurement under 0-5 T applied fields. This compound exhibits almost no thermal and magnetic hysteresis, thus potentially applicable in low temperature region for magnetic refrigerator material

Surface modification of nanodiamond through metal free atom transfer radical polymerization

Energy Technology Data Exchange (ETDEWEB)

Zeng, Guangjian; Liu, Meiying; Shi, Kexin; Heng, Chunning; Mao, Liucheng; Wan, Qing; Huang, Hongye [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); Deng, Fengjie, E-mail: fengjiedeng@aliyun.com [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); Zhang, Xiaoyong, E-mail: xiaoyongzhang1980@gmail.com [Department of Chemistry, Nanchang University, 999 Xuefu Avenue, Nanchang 330031 (China); Wei, Yen, E-mail: weiyen@tsinghua.edu.cn [Department of Chemistry and the Tsinghua Center for Frontier Polymer Research, Tsinghua University, Beijing, 100084 (China)

2016-12-30

Highlights: • Surface modification of ND with water soluble and biocompatible polymers. • Functionalized ND through metal free surface initiated ATRP. • The metal free surface initiated ATRP is rather simple and effective. • The ND-poly(MPC) showed high dispersibility and desirable biocompatibility. - Abstract: Surface modification of nanodiamond (ND) with poly(2-methacryloyloxyethyl phosphorylcholine) [poly(MPC)] has been achieved by using metal free surface initiated atom transfer radical polymerization (SI-ATRP). The ATRP initiator was first immobilized on the surface of ND through direct esterification reaction between hydroxyl group of ND and 2-bromoisobutyryl bromide. The initiator could be employed to obtain ND-poly(MPC) nanocomposites through SI-ATRP using an organic catalyst. The final functional materials were characterized by {sup 1}H nuclear magnetic resonance, transmission electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and thermo gravimetric analysis in detailed. All of these characterization results demonstrated that ND-poly(MPC) have been successfully obtained via metal free photo-initiated SI-ATRP. The ND-poly(MPC) nanocomposites shown enhanced dispersibility in various solvents as well as excellent biocompatibility. As compared with traditional ATRP, the metal free ATRP is rather simple and effective. More importantly, this preparation method avoided the negative influence of metal catalysts. Therefore, the method described in this work should be a promising strategy for fabrication of polymeric nanocomposites with great potential for different applications especially in biomedical fields.

Surface modification of nanodiamond through metal free atom transfer radical polymerization

International Nuclear Information System (INIS)

Zeng, Guangjian; Liu, Meiying; Shi, Kexin; Heng, Chunning; Mao, Liucheng; Wan, Qing; Huang, Hongye; Deng, Fengjie; Zhang, Xiaoyong; Wei, Yen

2016-01-01

Highlights: • Surface modification of ND with water soluble and biocompatible polymers. • Functionalized ND through metal free surface initiated ATRP. • The metal free surface initiated ATRP is rather simple and effective. • The ND-poly(MPC) showed high dispersibility and desirable biocompatibility. - Abstract: Surface modification of nanodiamond (ND) with poly(2-methacryloyloxyethyl phosphorylcholine) [poly(MPC)] has been achieved by using metal free surface initiated atom transfer radical polymerization (SI-ATRP). The ATRP initiator was first immobilized on the surface of ND through direct esterification reaction between hydroxyl group of ND and 2-bromoisobutyryl bromide. The initiator could be employed to obtain ND-poly(MPC) nanocomposites through SI-ATRP using an organic catalyst. The final functional materials were characterized by 1 H nuclear magnetic resonance, transmission electron microscopy, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and thermo gravimetric analysis in detailed. All of these characterization results demonstrated that ND-poly(MPC) have been successfully obtained via metal free photo-initiated SI-ATRP. The ND-poly(MPC) nanocomposites shown enhanced dispersibility in various solvents as well as excellent biocompatibility. As compared with traditional ATRP, the metal free ATRP is rather simple and effective. More importantly, this preparation method avoided the negative influence of metal catalysts. Therefore, the method described in this work should be a promising strategy for fabrication of polymeric nanocomposites with great potential for different applications especially in biomedical fields.

Coercivity enhancement in (Ce,Nd)-Fe-B sintered magnets prepared by adding NdH{sub x} powders

Energy Technology Data Exchange (ETDEWEB)

Zhang, Le-le [Key Laboratory of Integrated Exploitation of Bayan Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); School of Science, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Li, Zhu-bai, E-mail: lzbgj@163.com [Key Laboratory of Integrated Exploitation of Bayan Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Ma, Qiang; Li, Yong-feng; Zhao, Qian [Key Laboratory of Integrated Exploitation of Bayan Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); School of Science, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Zhang, Xue-feng, E-mail: xuefeng056@163.com [Key Laboratory of Integrated Exploitation of Bayan Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); School of Science, Inner Mongolia University of Science and Technology, Baotou 014010 (China)

2017-08-01

(Ce,Nd)-Fe-B sintered magnets were prepared by the addition of NdH{sub x} powders in Ce{sub 9}Nd{sub 4.5}Fe{sub 80}B{sub 6.5} powders. The coercivity is rather low in Ce{sub 9}Nd{sub 4.5}Fe{sub 80}B{sub 6.5} magnets, and Ce element prefers to distribute at the outer-layer of main phase (Ce,Nd){sub 2}Fe{sub 14}B. The investigation of scanning electron microscope shows that the addition of NdH{sub x} powders leads to the increase of Nd content at grain outer-layer of main phase owing to the element diffusion. Magnetization reversal undergoes the nucleation of reversed domain wall at grain outer-later, and the addition of NdH{sub x} powders leads to the increase in the nucleation field of reversed domain, giving rise to the significant improvement of coercivity. The larger amount addition of NdH{sub x} powders leads to the increase in the amount of intergranular phase, resulting in the decreases of the remanence, the squareness of demagnetization curve and the maximum energy product.

Nd-doped Bi2O3 nanocomposites: simple synthesis and improved photocatalytic activity for hydrogen production under visible light

Science.gov (United States)

Al-Namshah, Khadijah S.; Mohamed, Reda M.

2018-04-01

Bi2O3 has 2.4 eV band gap energy, which means it absorb in visible region. Though the photocatalytic activity of Bi2O3 is extremely little due to rapid rate of photogenerated electron-hole recombination. To face the economical and practical needs, the photocatalytic efficiency of Bi2O3 should be upgraded. In this paper, this was achieved by addition of neodymium to Bi2O3 nanosheets and Nd/Bi2O3 nanocomposites were prepared by a easy process at room temperature using a surfactant of Pluronic F127. The Bi2O3 nanosheets and Nd/Bi2O3 nanocomposites were investigated by many tools. The photocatalytic activity of Nd/Bi2O3 samples is better than Bi2O3 due to reduced band gap and reduced electron-hole recombination of Bi2O3 with addition of neodymium. In addition, Nd/Bi2O3 nanocomposites exhibit photocatalytic stability for hydrogen production which enables it to be reused on other occasions also.

Nd{sup 3+}-doped TeO{sub 2}-Bi{sub 2}O{sub 3}-ZnO transparent glass ceramics for laser application at 1.06 μm

Energy Technology Data Exchange (ETDEWEB)

Hu, Xiaolin; Luo, Zhiwei; Liu, Taoyong; Lu, Anxian [Central South of University, School of Materials Science and Engineering, Changsha (China)

2017-04-15

The high crystallinity transparent glass ceramics based on Nd{sup 3+}-doped 70TeO{sub 2}-15Bi{sub 2}O{sub 3}-15ZnO (TBZ) compositions were successfully prepared by two-step heat treatment process. The effects of Nd{sub 2}O{sub 3} content on the thermal, structural, mechanical, and optical properties of TBZ glass ceramics were studied. The incorporation of Nd{sub 2}O{sub 3} enhanced the crystallization tendency in the matrix glass composition. The crystal phase and morphology of Bi{sub 2}Te{sub 4}O{sub 11} in the glass ceramics were confirmed by X-ray diffraction and field emission scanning electron microscopy. Due to precipitate more crystal phase, the hardness values increased from 3.21 to 3.66 GPa. Eight absorption peaks were observed from 400 to 900 nm and three emission bands appeared in the range of 850-1400 nm. With the increasing of Nd{sub 2}O{sub 3} content from 0.5 to 2.5 wt%, the intensity of absorption peaks enhanced and the emission intensity increased up to 1.0 wt% and then fell down for further dopant concentration. The fluorescence decay lifetime decreased rapidly starting from 1.5 wt% Nd{sub 2}O{sub 3} content due to the obvious energy migration among Nd{sup 3+}. According to the extreme strong emission band around 1062 nm and the optimum Nd{sub 2}O{sub 3} content (1.0 wt%), N10 glass ceramic was considered as a potential material for 1.06 μm laser applications. (orig.)

Joint Force Quarterly. Issue 73, 2nd Quarter 2014

Science.gov (United States)

2014-04-01

Marine Corps/Matthew Bragg); UH-60M Black Hawk helicopter pilot and commander of C Company “War Lords,” 2nd Battalion (Assault), 10th Combat...organization’s performance is rare. Many change efforts are ill conceived and mostly cosmetic : shuf- fling organizational boxes, titles, and authorities...UNIDO_Header_Site/Subsites/Green_Indus- try_Asia_Conference__Maanila_/GC13/Gal- lagher_Report.pdf>. 37 Hartmut. 38 Tim Rice , “Meals per gallon, the impact of

Crystal growth, optical properties, and continuous-wave laser operation of Nd3+-doped CaNb2O6 crystal

International Nuclear Information System (INIS)

Cheng, Y; Xu, X D; Xiao, X D; Li, D Z; Zhao, C C; Zhou, S M; Xin, Z; Yang, X B; Xu, J

2009-01-01

Laser crystal Nd:CaNb 2 O 6 with excellent quality has been grown by Czochralski technique. The effective segregation coefficient of Nd 3+ was studied by X-ray fluorescence method. The polarized absorption spectra and the fluorescence spectra of Nd:CaNb 2 O 6 were measured at room temperature. The peak absorption cross section was calculated to be 6.202×10 -20 cm 2 with a broad FWHM of 7 nm at 808 nm for E ∥ a light polarization. The emission cross section at 1062 nm is 9.87×10 -20 cm 2 . We report what we believe to be the first demonstration of the continuous-wave Nd:CaNb 2 O 6 laser operation under diode pumping. Output power of 1.86 W at 1062 nm was obtained with a slope efficiency of 19% in the CW regime

Crystal growth, optical properties, and continuous-wave laser operation of Nd3+-doped CaNb2O6 crystal

Science.gov (United States)

Cheng, Y.; Xu, X. D.; Xin, Z.; Yang, X. B.; Xiao, X. D.; Li, D. Z.; Zhao, C. C.; Xu, J.; Zhou, S. M.

2009-10-01

Laser crystal Nd:CaNb2O6 with excellent quality has been grown by Czochralski technique. The effective segregation coefficient of Nd3+ was studied by X-ray fluorescence method. The polarized absorption spectra and the fluorescence spectra of Nd:CaNb2O6 were measured at room temperature. The peak absorption cross section was calculated to be 6.202×10-20 cm2 with a broad FWHM of 7 nm at 808 nm for E ∥ a light polarization. The emission cross section at 1062 nm is 9.87×10-20 cm2. We report what we believe to be the first demonstration of the continuous-wave Nd:CaNb2O6 laser operation under diode pumping. Output power of 1.86 W at 1062 nm was obtained with a slope efficiency of 19% in the CW regime.

Pressure influence on magnetic properties of Nd{sub 2}RhIn{sub 8}

Energy Technology Data Exchange (ETDEWEB)

Javorský, P., E-mail: javor@mag.mff.cuni.cz [Charles University in Prague, Faculty of Mathematics and Physics, Department of Condensed Matter Physics, Ke Karlovu 5, 121 16 Prague 2, The Czech Republic (Czech Republic); Kaštil, J.; Míšek, M. [Institute of Physics ASCR, v.v.i., Na Slovance 2, 182 21 Praha 8, The Czech Republic (Czech Republic); Prachařová, M.; Prchal, J.; Klicpera, M.; Kratochvílová, M. [Charles University in Prague, Faculty of Mathematics and Physics, Department of Condensed Matter Physics, Ke Karlovu 5, 121 16 Prague 2, The Czech Republic (Czech Republic)

2016-08-01

We have studied the pressure effect on the magnetic phase diagram of tetragonal Nd{sub 2}RhIn{sub 8}. The magnetization under uniaxial pressure up to 5.3 kbar applied along the tetragonal c-axis and the heat capacity under hydrostatic pressure were measured in magnetic fields up to 7 and 14 T, respectively. Both types of measurements reveal an increase of T{sub N} with increasing pressure; the effect is considerably stronger for the uniaxial pressure. Considering also the anisotropic compressibility in this family of compounds, we conclude that T{sub N} increases with decreasing c/a. The phase boundary between the ground-state AF1 phase and the field-induced AF2 phase shifts slightly to higher magnetic fields with increasing pressure. The ground state phase is thus stabilized by applying pressure. The magnetic phase diagram is constructed. - Highlights: • Hydrostatic and uniaxial pressure along the c-axis cause an increase of TN. • The ground state magnetic structure is stabilized with decreasing Nd-Nd distances. • The change of T{sub N} is related to change of structural and crystal-field parameters.

Precipitation of Nd-Ca carbonate solid solution at 25 degrees C

International Nuclear Information System (INIS)

Carroll, S.A.

1993-01-01

The formation of a Nd-Ca carbonate solid solution was studied by monitoring the reactions of calcite with aqueous Nd, orthorhombic NdOHCO 3 (s) with aqueous Ca, and calcite with hexagonal Nd-carbonate solid phase as a function of time at 25 degrees C and controlled pCO 2 (g). All experiments reached steady state after 200 h of reaction. The dominant mechanism controlling the formation of the solid solution was precipitation of a Nd-Ca carbonate phase from the bulk solution as individual crystals or at the orthorhombic NdOHCO 3 (s)-solution interface. The lack of Nd adsorption or solid solution at the calcite-solution interface suggests that the solid solution was orthorhombic and may be modeled as a mixture of orthorhombic NdOHCO 3 (s) and aragonite. Orthorhombic NdOHCO 3 (s) was determined to be the stable Nd-carbonate phase in the Nd-CO 2 -H 2 O system at pCO 2 (g) 0.1 atmospheres at 25 degrees C. The equilibrium constant corrected to zero ionic strength for orthorhombic NdOHCO 3 (s) solubility is 10 10.41(±0.29) for the following: NdOHCO 3 (s) + 3H + = Nd 3+ + CO 2 (g) + H 2 O. Results are discussed in relation to radioactive waste disposal by burial, and specifically in relation to americium chemistry

Clinical evaluation of the 2nd generation radio-receptor assay for anti-thyrotropin receptor antibodies (TRAb) in Graves' disease

International Nuclear Information System (INIS)

Giovanella, L.; Ceriani, L.; Garancini, S.

2002-01-01

Full text: Detection of autoantibodies to the TSH receptor by radioreceptorial assays (RRA) is largely requested in clinical practice for the diagnosis of Graves' disease and its differentiation from diffuse thyroid autonomy. Additionally, TRAb measurement during antithyroid drug treatment can be useful to evaluate the risk of disease's relapse alter therapy discontinuation. Nevertheless, some patients affected by Graves' disease are TRAb negative when 1st generation assay is used. Recently a new RRA method for TRAb assay was developed by using human recombinant TSH-receptor and solid-phase technique. Aim of our work was the comparison between 1st and 2nd generation TRAb assays in Graves' disease patients and, particularly, the evaluation of 2nd generation test in a sub-group of patients affected by Graves' disease but with negative 1st generation TRAb assay. We evaluated the diagnostic performance of a newly developed 2nd generation TRAb assay (DYNOtest(r) TRAK human, BRAHMS Diagnostica GmbH, Germany) in 46 patients affected by Graves' disease with negative 1st generation TRAb assay (TRAK Assay(r), BRAHMS Diagnostica GmbH, Germany) . A control groups of 50 Graves' disease patients with positive 1st generation TRAb assay, 50 patients affected by Hashimoto's thyroiditis and 50 patients affected by nodular goiter were also examined. 41 out of 46 patients affected by Graves' disease with negative 1st generation TRAb assay showed a positive 2nd generation test. The overall sensitivity of the 2nd generation test was significantly improved respect the 1st generation assay in Graves' disease patients (χ 2 = 22.5, p<0.0001). 1 and 3 out of 50 patients affected by Hashimoto's thyroiditis were positive by 1st and 2nd generation TRAB assay, respectively. All these patients showed primary hypothyroidism. No differences resulted in euthyroid Hashimoto's thyroiditis sub-group and in nodular goiter control group. The 2nd generation TRAB assay is clearly more sensitive than the 1

Connected vehicle pilot deployment program phase 2, data management plan - Wyoming

Science.gov (United States)

2017-04-10

The Wyoming Department of Transportations (WYDOT) Connected Vehicle (CV) Pilot Deployment Program is intended to develop a suite of applications that utilize vehicle to infrastructure (V2I) and vehicle to vehicle (V2V) communication technology to ...

Investigation of BaMoO4-Ln2(MoO4)3 systems (Ln = Nd, Sm, Yb)

International Nuclear Information System (INIS)

Vakulyuk, V.V.; Evdokimov, A.A.; Khomchenko, G.P.

1982-01-01

Using the methods of X-ray phase and differential-thermal analyses phase ratios in the systems BaMoO 4 -Ln 2 (MoO 4 ) 3 (Ln=Nd, Sm, Yb); BaNd 2 (MoO 4 ) 4 -MaGd 2 (MoO 4 ) are studied. Unit cell parameters and the character of melting of the compounds BaLn 2 (MoO 4 ) 4 are specified. Effect of growth conditions on laminated nature of BaGd 2 (MoO 4 ) 4 monocrystals is studied

Synthesis and crystal structure of a new neodymium(III) selenate-selenite: Nd2(SeO4)(SeO3)2(H2O)2

International Nuclear Information System (INIS)

Feng Meiling; Mao Jianggao

2005-01-01

The title new neodymium(III) selenate-selenite was obtained by hydrothermal reactions of neodymium(III) oxide, H 2 SeO 4 and 1,10-phenanthroline at 140 o C. Its structure was established by single-crystal X-ray diffraction. The title compound crystallizes in the monoclinic space group C2/c with cell parameters of a = 12.258(2) A, b 7.1024(15) A, c = 13.391(3) A, β = 104.250(2) o . The structure of Nd 2 (SeO 4 )(SeO 3 ) 2 (H 2 O) 2 is isomorphous with that of Er 2 (SeO 4 )(SeO 3 ) 2 (H 2 O) 2 , which was refined in the monoclinic space group C2 with the disordered selenate group. It features an ordered 3D network with channels along b-axis. The selenate or selenite groups alone can form a 2D layer with the Nd(III) ions. IR spectrum, TGA and luminescent studies have also been performed

Magnetization reversal of a Nd-Cu-infiltrated Nd-Fe-B nanocrystalline magnet observed with small-angle neutron scattering

Energy Technology Data Exchange (ETDEWEB)

Saito, Kotaro, E-mail: kotaro.saito@kek.jp; Ono, Kanta [Institute of Materials Structure Science, High Energy Accelerator Research Organization, 1-1 Oho, 305-0803 Tsukuba (Japan); Ueno, Tetsuro [Elements Strategy Initiative Center for Magnetic Materials, National Institute for Materials Science, 1-2-1 Sengen, 305-0047 Tsukuba (Japan); Yano, Masao; Shoji, Tetsuya; Sakuma, Noritsugu; Manabe, Akira; Kato, Akira [Toyota Motor Corporation, Toyota, Aichi 471-8571 (Japan); Harada, Masashi [Toyota Central R and D Labs, Inc., Aichi 480-1192 (Japan); Keiderling, Uwe [Helmholtz-Zentrum Berlin für Materialien and Energie, 14109 Berlin (Germany)

2015-05-07

The magnetization reversal process of Nd-Fe-B nanocrystalline magnets infiltrated with Nd-Cu alloy was examined using small-angle neutron scattering (SANS). The magnetic-field dependence of SANS intensity revealed a qualitative difference between Nd-Cu-infiltrated samples and as-deformed samples. Insufficient magnetic isolation along the direction perpendicular to the nominal c-axis is expected from comparable SANS intensities for different ranges of q values along this direction. For small q values near the coercivity field, Nd-Cu-infiltrated samples show a noticeable reduction in SANS intensity along the nominal c-axis, which is parallel to the external magnetic field. This indicates less spatial fluctuation of magnetic moments in Nd-Cu-infiltrated samples, owing to magnetically isolated Nd{sub 2}Fe{sub 14}B grains.

Magnetization reversal of a Nd-Cu-infiltrated Nd-Fe-B nanocrystalline magnet observed with small-angle neutron scattering

International Nuclear Information System (INIS)

Saito, Kotaro; Ono, Kanta; Ueno, Tetsuro; Yano, Masao; Shoji, Tetsuya; Sakuma, Noritsugu; Manabe, Akira; Kato, Akira; Harada, Masashi; Keiderling, Uwe

2015-01-01

The magnetization reversal process of Nd-Fe-B nanocrystalline magnets infiltrated with Nd-Cu alloy was examined using small-angle neutron scattering (SANS). The magnetic-field dependence of SANS intensity revealed a qualitative difference between Nd-Cu-infiltrated samples and as-deformed samples. Insufficient magnetic isolation along the direction perpendicular to the nominal c-axis is expected from comparable SANS intensities for different ranges of q values along this direction. For small q values near the coercivity field, Nd-Cu-infiltrated samples show a noticeable reduction in SANS intensity along the nominal c-axis, which is parallel to the external magnetic field. This indicates less spatial fluctuation of magnetic moments in Nd-Cu-infiltrated samples, owing to magnetically isolated Nd 2 Fe 14 B grains

Structural and magnetic characterization of Nd-based Nd-Fe and Nd-Fe-Co-Al metastable alloys

International Nuclear Information System (INIS)

Kumar, G.

2005-01-01

The aim of the present work is to characterize a metastable hard magnetic phase referred to as ''A1'' in Nd-Fe alloys, which forms as a part of the fine eutectic depending on the composition and cooling rate. In order to define the range of composition for the formation of A1, Nd 100-x Fe x (x=20,25,40) alloys are cooled at about 150 K/s. The effect of cooling rate on the formation of hard magnetic A1 is studied by investigating the Nd 80 Fe 20 alloys cooled at different rates. The Nd-richer regions are identified as dhcp Nd and fcc Nd-Fe solid solution. However, the Fe-richer regions also referred to as A1, are diffuse and give an average composition of Nd 56 Fe 44 . HRTEM images of the Fe-richer regions reveal the presence of 5-10 nm crystallites embedded in an amorphous phase. The demagnetization curves the hard magnetic Nd80Fe20 measured at temperatures above 30 K are typical of a hard magnetic material. The measurements of initial magnetization, field dependence of coercivity, and temperature dependence of coercivity suggest the Stoner-Wohlfarth type magnetization reversal process for the hard magnetic A1. The values of anisotropy constant are estimated by fitting the magnetization data to the law-of-approach to saturation. The temperature dependence of anisotropy constant and the coercivity indicate that the origin of coercivity is magnetic anisotropy

Structural studies on W6+ and Nd3+ substituted La2Mo2O9 materials

International Nuclear Information System (INIS)

Marrero-Lopez, David; Canales-Vazquez, Jesus; Zhou Wuzong; Irvine, John T.S.; Nunez, Pedro

2006-01-01

The structure of a series of new ionic conductors based in lanthanum molybdate (La 2 Mo 2 O 9 ) has been investigated using transmission electron microscopy (TEM), high-resolution X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The superstructure 2a c x3a c x4a c of the low temperature α-polymorph relative to the β-polymorph was confirmed by HRTEM imaging and electron diffraction. Furthermore, the effects of partial cation substitution in the La 2-x Nd x Mo 2 O 9 and La 2 Mo 2-y W y O 9 series have been also evaluated in the search of new clues to understand the structure and stabilisation of the high temperature and better conductor β-polymorph. The thermal analysis studies show that Nd-substitution does not stabilise completely the β-polymorph at room temperature, although no superstructure ordering was observed by both XRD and HRTEM. On the other hand, W-substitution stabilises the cubic β-polymorph for y>0.25, although, electron diffraction indicates a slight distortion from the cubic symmetry for low W-content. This distortion disappears as the W content increases and the Rietveld refinements gradually render better results

X-ray structural study of Nd[N(CN)2]3x2OP(NMe2)3

International Nuclear Information System (INIS)

Kapshuk, A.A.; Skopenko, V.V.

1985-01-01

The results of X-ray structure study of Nd(N(CN) 2 ) 3 x2OP(NMe) 2 ) 3 are presented. The crystals are monoclinic: a=12,787(6), b=17.731(9), c=15.302(5) A, γ=114.84(3) deg, Z=4, sp.gr. p2 1 /n. The structure is formed of infinite corrugated netting consisting of neodymium atoms, coordinating two OP(NMe 2 ) 3 molecules, and three bidentate-bridge dicyanamide groups. Neodymium coordination number is 8, coordination polyhedron is a distorted twocapped trigonal prism. Certain aspects of crystal chemistry of dicyanamide complexes are discussed

Liquid metal extraction of Nd from NdFeB magnet scrap

Energy Technology Data Exchange (ETDEWEB)

Xu, Yanchen [Iowa State Univ., Ames, IA (United States)

1999-12-10

This research involves using molten magnesium (Mg) to remove neodymium (Nd) from NdFeB magnet scrap by diffusion. The results show that liquid metal extraction of Nd may be a viable and inexpensive method for recovering the expensive rare earth element Nd for use in Mg castings.

2nd conference on Continuous Media with Microstructure

CERN Document Server

Kuczma, Mieczysław

2016-01-01

This book presents research advances in the field of Continuous Media with Microstructure and considers the three complementary pillars of mechanical sciences: theory, research and computational simulation. It focuses on the following problems: thermodynamic and mathematical modeling of materials with extensions of classical constitutive laws, single and multicomponent media including modern multifunctional materials, wave propagation, multiscale and multiphysics processes, phase transformations, and porous, granular and composite materials. The book presents the proceedings of the 2nd Conference on Continuous Media with Microstructure, which was held in 2015 in Łagów, Poland, in memory of Prof. Krzysztof Wilmański. .

MFM study of NdFeB and NdFeB/Fe/NdFeB thin films

International Nuclear Information System (INIS)

Gouteff, P.C.; Folks, L.; Street, R.

1998-01-01

Domain structures of NdFeB thin films, ranging in thickness between 1500 and 29 nm, have been studied qualitatively by magnetic force microscopy (MFM). Samples were prepared using a range of sputtering conditions resulting in differences in properties such as texture, coercivity and magnetic saturation. MFM images of all the films showed extensive interaction domain structures, similar to those observed in nanocrystalline bulk NdFeB. An exchange-coupled NdFeB/Fe/NdFeB trilayer with layer thicknesses 18 nm/15 nm/18 nm, respectively, was also examined using MFM. (orig.)

Self-propagating synthesis and aqueous durability of Nd-bearing zirconolite-rich composites using Ca(NO{sub 3}){sub 2} as the oxidant

Energy Technology Data Exchange (ETDEWEB)

Zhang, Kuibao, E-mail: xiaobao320@163.com [State Key Laboratory Cultivation Base for Nonmetal Composite and Functional Materials, Southwest University of Science and Technology, Mianyang, Sichuan 621010 (China); National Defense Key Discipline Lab of Nuclear Waste and Environmental Safety, Southwest University of Science and Technology, Mianyang 621010 (China); He, Shihong [State Nuclear Power Research Institute, Beijing 100029 (China); Yin, Dan; Peng, Le; Wu, Jingjun [State Key Laboratory Cultivation Base for Nonmetal Composite and Functional Materials, Southwest University of Science and Technology, Mianyang, Sichuan 621010 (China)

2016-09-15

Synroc is recognized as the second-generation waste form for safety disposal of high-level radioactive waste (HLW). In this study, zirconolite-rich Synroc waste form was readily synthesized by self-propagating high-temperature plus quick pressing (SHS/QP) using Ca(NO{sub 3}){sub 2} as the oxidant and Ti as the reductant. As the surrogate of trivalent actinides, Nd{sub 2}O{sub 3} was introduced to equally substitute the Ca and Zr sites of zirconolite with nominal stoichiometry of Ca{sub 1−x}Zr{sub 1−x}Nd{sub 2x}Ti{sub 2}O{sub 7}. The results demonstrate that zirconolite, perovskite and pyrochlore (Ca{sub 2}Ti{sub 2}O{sub 6}) coexist as the ceramic components after SHS reaction. The introduction of Nd{sub 2}O{sub 3} promotes the formation of perovskite. Nd is mostly incorporated into the Ca sites of these phases. The normalized elemental leaching rates of Ca and Nd are fairly constant in low values of 1.80 × 10{sup −2} g m{sup −2} d{sup −1} and 6.12 × 10{sup −4} g m{sup −2} d{sup −1} after 42 days. - Highlights: • Zirconolite-rich composite was synthesized by SHS using Ca(NO{sub 3}){sub 2} as the oxidant. • Nd{sub 2}O{sub 3} was successfully immobilized into the crystal structure of this waste form. • Nd was mostly incorporated into the Ca sites of zirconolite, perovskite and pyrochlore. • The normalized leaching rates of Ca and Nd are in relatively low values.

Sm-Nd in marine carbonates and phosphates: implications for Nd isotopes in seawater and crustal ages

International Nuclear Information System (INIS)

Shaw, H.F.; Wasserburg, G.J.

1985-01-01

This study explores the possibility of establishing Nd isotopic variations in seawater over geologic time. Calcite, aragonite and apatite are examined as possible phases recording seawater values of epsilonsubNd. Modern, biogenic and inorganically precipitated calcite and aragonite from marine environments were found to have Nd concentrations of from 0.2 to 70 ppb, showing that primary marine CaCO 3 contains little REE and that Nd/Ca is not greatly enhanced relative to seawater during carbonate precipitation. Very young marine limestone and dolomite containing no continental detritus have approx. 200 ppb Nd. All the carbonates are LREE enriched. Modern and very young Atlantic and Pacific carbonates have epsilonsub(Nd) in the range of shallow Atlantic and Pacific seawater respectively, implying that they derive their REE from local seawater. The Nd in well preserved carbonate fossils is 4 ppb, much greater than in their modern counterparts but like the high values found for carbonates in other studies. Results are also reported for apatite. They suggest that sedimentary apatite can be used to determine epsilonsub(Nd)(T) in ancient seawater. The seawater values so inferred range between -1.7 and -8.9 over the last 700 my and lie in the range of modern seawater, showing no evidence for drastic changes. (U.K.)

Multiferroic and visible light photocatalytic properties of six-layered perovskite oxide Nd{sub 6}Ti{sub 4}Fe{sub 2}O{sub 20}

Energy Technology Data Exchange (ETDEWEB)

Cheng, Xiangyi; Yang, Hongshun; Ruan, Keqing; Xu, Xiaoliang [University of Science and Technology of China, Key Laboratory of Strongly-Coupled Quantum Matter Physics, Chinese Academy of Sciences and School of Physical Sciences, Hefei (China); Meng, Dechao [University of Science and Technology of China, Hefei National Laboratory for Physical Sciences at Microscale, Hefei (China)

2017-04-15

The layered perovskite-related oxide Nd{sub 6}Ti{sub 4}Fe{sub 2}O{sub 20} was prepared by incorporating NdFeO{sub 3} in the host Nd{sub 2}Ti{sub 2}O{sub 7} using floating-zone melting technique. XRD and HRTEM results suggested that the material has a layered structure of n = 6 type. Nd{sub 6}Ti{sub 4}Fe{sub 2}O{sub 20} exhibited spin glass-like behavior, and its magnetic behavior was affected by magnetic Nd{sup 3+} ions strongly at low temperature. The ferromagnetic and ferroelectric properties were observed by magnetic and PFM measurements at the room temperature. UV-Vis absorption spectroscopy revealed that the compound is a visible light absorbing photocatalyst with a direct band gap of 2.2 eV. In addition, the photocatalytic behaviors of bulk Nd{sub 6}Ti{sub 4}Fe{sub 2}O{sub 20} were evaluated by photodegradation of rhodamine B under visible light irradiation. (orig.)

(SiC/AlN)2 multilayer film as an effective protective coating for sintered NdFeB by magnetron sputtering

Science.gov (United States)

You, Yu; Li, Heqin; Huang, Yiqin; Tang, Qiong; Zhang, Jing; Xu, Jun

2017-08-01

SiC/AlN and (SiC/AlN)2 multilayer films with a well-arranged bilayer structure and a four-layer structure are prepared respectively on NdFeB substrates by a magnetron sputtering method. Crystal phase and microstructures of the SiC/AlN and (SiC/AlN)2 films are investigated using x-ray diffraction (XRD), field-emission scanning electron microscope (FESEM) and atomic force microscope (AFM). It is observed that the surface of the (SiC/AlN)2 four-layer film is much denser and smoother than that of the SiC/AlN bilayer film. Corrosion behaviors of the NdFeB substrates coated with SiC/AlN and (SiC/AlN)2 films as well as the bare NdFeB substrate are evaluated by potentiodynamic polarization curve tests. It is revealed that the lateral growth structures developed in interfaces are favorable for an enhanced corrosion resistance. Corrosion current densities of the (SiC/AlN)2 coated NdFeB measured in acid, alkali and salt solutions are 2.796  ×  10-9, 3.65  ×  10-6, and 2.912  ×  10-6 A cm-2, respectively, which are much lower than those of the bare NdFeB and the SiC/AlN coated NdFeB.

RAPIDLY-SOLIDIFIED PERMANENT MAGNET MATERIALS: FACTORS AFFECTING QUENCHABILITY AND MAGNETIC PROPERTIES IN Nd2Fe14B

International Nuclear Information System (INIS)

LEWIS, L.H.; KRAMER, M.J.; MCCALLUM, R.W.; BRANAGAN, D.J.

1999-01-01

Insight into the solidification behavior of Nd 2 Fe 14 B-based materials processed by rapid solidification techniques has been obtained by a systematic experimental study of the Curie temperatures of selected phases found in these materials. Nd 2 Fe 14 B-based materials fabricated by two disparate rapid solidification techniques, inert gas atomization (IGA) and melt-spinning, has been studied. The compositions of the starting materials have been altered with additions of the refractory elements Ti and C which are known to alter the solidification behavior of these materials. Special emphasis has been placed on trying to understand the effect of alloying additions upon the nature of the quenched glass, the distribution of the elemental additions within the Nd 2 Fe 14 B lattice and the evolution of the elemental partitioning with quench rate and annealing condition. The experimental Curie temperature data obtained using thermal analysis methods from the particles produced by gas-atomization is consistent with both an ejection of quenched-in refractory species from the crystalline Nd 2 Fe 14 B lattice and with increased crystallographic order as particle size, and hence grain size, increases. Magnetic ac susceptibility measurements performed on nominally-amorphous Nd 2 Fe 14 B ribbons produced by melt-spinning indicate a decrease of the Curie temperature with increasing quench rate, a result that may be attributed either to the degree of Ti/C retention in the glass or to the degree of disorder in the glass, independent of Ti/C retention

Multi-Disciplinary Design Optimization of Hypersonic Air-Breathing Vehicle

Science.gov (United States)

Wu, Peng; Tang, Zhili; Sheng, Jianda

2016-06-01

A 2D hypersonic vehicle shape with an idealized scramjet is designed at a cruise regime: Mach number (Ma) = 8.0, Angle of attack (AOA) = 0 deg and altitude (H) = 30kms. Then a multi-objective design optimization of the 2D vehicle is carried out by using a Pareto Non-dominated Sorting Genetic Algorithm II (NSGA-II). In the optimization process, the flow around the air-breathing vehicle is simulated by inviscid Euler equations using FLUENT software and the combustion in the combustor is modeled by a methodology based on the well known combination effects of area-varying pipe flow and heat transfer pipe flow. Optimization results reveal tradeoffs among total pressure recovery coefficient of forebody, lift to drag ratio of vehicle, specific impulse of scramjet engine and the maximum temperature on the surface of vehicle.