Total surface area change of Uranium dioxide fuel in function of burn-up and its impact on fission gas release during neutron irradiation for small, intermediate and high burn-up

International Nuclear Information System (INIS)

Szuta, M.

2011-01-01

In the early published papers it was observed that the fractional fission gas release from the specimen have a tendency to increase with the total surface area of the specimen - a fairy linear relationship was indicated. Moreover it was observed that the increase of total surface area during irradiation occurs in the result of connection the closed porosity with the open porosity what in turn causes the increase of fission gas release. These observations let us surmise that the process of knock-out release is the most significant process of fission gas release since its quantity is proportional to the total surface area. Review of the experiments related to the increase of total surface area in function of burn-up is presented in the paper. For very high burn-up the process of grain sub-division (polygonization) occurs under condition that the temperature of irradiated fuel lies below the temperature of grain re-crystallization. Simultaneously with the process of polygonization, the increase in local porosity and the decrease in local density in function of burn-up occurs, which leads to the increase of total surface area. It is suggested that the same processes take place in the transformed fuel as in the original fuel, with the difference that the total surface area is so big that the whole fuel can be treated as that affected by the knock-out process. This leads to explanation of the experimental data that for very high burn-up (>120 MWd/kgU) the concentration of xenon is constant. An explanation of the grain subdivision process in function of burn-up in the 'athermal' rim region in terms of total surface area, initial grain size and knock-out release is undertaken. Correlation of the threshold burn-up, the local fission gas concentration, local total surface area, initial and local grain size and burn-up in the rim region is expected. (author)

The release of silver nanoparticles from commercial toothbrushes

Energy Technology Data Exchange (ETDEWEB)

Mackevica, Aiga, E-mail: aima@env.dtu.dk; Olsson, Mikael Emil; Hansen, Steffen Foss

2017-01-15

Highlights: • Ag and Ag nanoparticle release was measured from two types of toothbrushes. • Maximum release for entire intended product use period was 10 ng Ag per toothbrush. • Released Ag nanoparticles had median sizes from 42 to 47 nm. • Up to 2.8% of total Ag released was detected in nanoparticulate form. - Abstract: The use of silver nanoparticles (NPs) in commercial products has become increasingly common in the past decade, mostly due to their antimicrobial properties. Using Ag NP-containing articles may lead to particle release, which raises concern of human and environmental safety. The published literature addressing particle release is scarce, especially when it comes to quantifying exposure to NPs specifically. In this study, we have experimentally investigated the release of total Ag and Ag NP from commercially available toothbrushes i.e. biodegradable toothbrushes for adults and toothbrushes for children. Toothbrushes were immersed and abraded in tap water for 24 h corresponding to more than the whole intended usage time of a toothbrush. The total amount of released Ag was quantified by inductively coupled plasma—mass spectrometry (ICP-MS) analysis, and the Ag NPs were characterized by single particle ICP-MS and transmission electron microscopy (TEM). The median size of the released Ag NPs ranged from 42 to 47 nm, and the maximum total Ag release was 10.2 ng per toothbrush. The adult toothbrushes were generally releasing more total Ag and NPs than children toothbrushes. In conclusion, our results indicate that the use of Ag NP-impregnated toothbrushes can cause consumer as well as environmental exposure to Ag NPs.

The release of silver nanoparticles from commercial toothbrushes

International Nuclear Information System (INIS)

Mackevica, Aiga; Olsson, Mikael Emil; Hansen, Steffen Foss

2017-01-01

Highlights: • Ag and Ag nanoparticle release was measured from two types of toothbrushes. • Maximum release for entire intended product use period was 10 ng Ag per toothbrush. • Released Ag nanoparticles had median sizes from 42 to 47 nm. • Up to 2.8% of total Ag released was detected in nanoparticulate form. - Abstract: The use of silver nanoparticles (NPs) in commercial products has become increasingly common in the past decade, mostly due to their antimicrobial properties. Using Ag NP-containing articles may lead to particle release, which raises concern of human and environmental safety. The published literature addressing particle release is scarce, especially when it comes to quantifying exposure to NPs specifically. In this study, we have experimentally investigated the release of total Ag and Ag NP from commercially available toothbrushes i.e. biodegradable toothbrushes for adults and toothbrushes for children. Toothbrushes were immersed and abraded in tap water for 24 h corresponding to more than the whole intended usage time of a toothbrush. The total amount of released Ag was quantified by inductively coupled plasma—mass spectrometry (ICP-MS) analysis, and the Ag NPs were characterized by single particle ICP-MS and transmission electron microscopy (TEM). The median size of the released Ag NPs ranged from 42 to 47 nm, and the maximum total Ag release was 10.2 ng per toothbrush. The adult toothbrushes were generally releasing more total Ag and NPs than children toothbrushes. In conclusion, our results indicate that the use of Ag NP-impregnated toothbrushes can cause consumer as well as environmental exposure to Ag NPs.

Fission fragment yields and total kinetic energy release in neutron-induced fission of235,238U,and239Pu

Science.gov (United States)

Tovesson, F.; Duke, D.; Geppert-Kleinrath, V.; Manning, B.; Mayorov, D.; Mosby, S.; Schmitt, K.

2018-03-01

Different aspects of the nuclear fission process have been studied at Los Alamos Neutron Science Center (LANSCE) using various instruments and experimental techniques. Properties of the fragments emitted in fission have been investigated using Frisch-grid ionization chambers, a Time Projection Chamber (TPC), and the SPIDER instrument which employs the 2v-2E method. These instruments and experimental techniques have been used to determine fission product mass yields, the energy dependent total kinetic energy (TKE) release, and anisotropy in neutron-induced fission of U-235, U-238 and Pu-239.

Cetirizine release from cyclodextrin formulated compressed chewing gum

DEFF Research Database (Denmark)

Stojanov, Mladen; Larsen, Kim Lambertsen

2012-01-01

release patterns, but with variations in the total amount released. Chewing gum formulated with cetirizine alone, demonstrated a release of 75% after 8 min of chewing. The presence of CDs resulted in increased cetirizine release. The analysis of variance (ANOVA) demonstrated that parameters with the most...... the statistical analysis (ANOVA) demonstrated significance in the release (P

Comparing the Immediate Effects of a Total Motion Release Warm-up and a Dynamic Warm-up Protocol on the Dominant Shoulder in Baseball Athletes.

Science.gov (United States)

Gamma, Stephen C; Baker, Russell; May, James; Seegmiller, Jeff G; Nasypany, Alan; Iorio, Steven M

2018-04-10

Gamma, SC, Baker, R, May, J, Seegmiller, JG, Nasypany, A, and Iorio, SM. Comparing the immediate effects of a total motion release warm-up and a dynamic warm-up protocol on the dominant shoulder in baseball athletes. J Strength Cond Res XX(X): 000-000, 2017-A decrease in total range of motion (ROM) of the dominant shoulder may predispose baseball athletes to increased shoulder injury risk; the most effective technique for improving ROM is unknown. The purpose of this study was to compare the immediate effects of Total Motion Release (TMR) to a generic dynamic warm-up program in baseball athletes. Baseball athletes (n = 20) were randomly assigned to an intervention group: TMR group (TMRG; n = 10) or traditional warm-up group (TWG; n = 10). Shoulder ROM measurements were recorded for internal rotation (IR) and external rotation (ER), the intervention was applied, and postmeasurements were recorded. Each group then received the other intervention and postmeasurements were again recorded. The time main effect (p ≤ 0.001) and the time × group interaction effect were significant (p ≤ 0.001) for IR and ER. Post hoc analysis revealed that TMR produced significant increases in mean IR (p ≤ 0.005, d = 1.52) and ER (p ≤ 0.018, d = 1.22) of the dominant shoulder initially. When groups crossed-over, the TMRG experienced a decrease in mean IR and ER after the dynamic warm-up, whereas the TWG experienced a significant increase in mean IR (p ≤ 0.001, d = 3.08) and ER (p ≤ 0.001, d = 2.56) after TMR intervention. Total Motion Release increased IR and ER of the dominant shoulder more than a dynamic warm-up. Dynamic warm-up after TMR also resulted in decreased IR and ER; however, TMR after dynamic warm-up significantly improved IR and ER. Based on these results, TMR is more effective than a generic dynamic warm-up for improving dominant shoulder ROM in baseball players.

131I release from a HTGR during the LOFC accident

International Nuclear Information System (INIS)

Foley, J.E.

1975-03-01

The time-dependent release of 131 I from both the core and the containment building of a high temperature gas-cooled (HTGR) reactor during the loss of forced coolant (LOFC) accident is studied. A simplified core release model is combined with a containment building release model so that the total amount of the isotope released to the environment can be calculated. The time-dependent release of 131 I from the core during the LOFC accident is primarily a function of the time-dependent core temperatures and the failed fuel release constants. The most important factor in calculating the amount of the isotope released to the environment is the total amount released into the containment building. (U.S.)

A randomized study to compare the efficacy and safety of extended-release and immediate-release tramadol HCl/acetaminophen in patients with acute pain following total knee replacement.

Science.gov (United States)

Park, Yong-Beom; Ha, Chul-Won; Cho, Sung-Do; Lee, Myung-Chul; Lee, Ju-Hong; Seo, Seung-Suk; Kang, Seung-Baik; Kyung, Hee-Soo; Choi, Choong-Hyeok; Chang, NaYoon; Rhim, Hyou Young Helen; Bin, Seong-Il

2015-01-01

To evaluate the relative efficacy and safety of extended-release tramadol HCl 75 mg/acetaminophen 650 mg (TA-ER) and immediate-release tramadol HCl 37.5 mg/acetaminophen 325 mg (TA-IR) for the treatment of moderate to severe acute pain following total knee replacement. This phase III, double-blind, placebo-controlled, parallel-group study randomized 320 patients with moderate to severe pain (≥4 intensity on an 11 point numeric rating scale) following total knee replacement arthroplasty to receive oral TA-ER (every 12 hours) or TA-IR (every 6 hours) over a period of 48 hours. In the primary analysis, TA-ER was evaluated for efficacy non-inferior to that of TA-IR based on the sum of pain intensity difference (SPID) at 48 hours after the first dose of study drug (SPID48). Secondary endpoints included SPID at additional time points, total pain relief at all on-therapy time points (TOTPAR), sum of SPID and TOTPAR at all on-therapy time points (SPID + TOTPAR), use of rescue medication, subjective pain assessment (PGIC, Patient Global Impression of Change), and adverse events (AEs). Analysis of the primary efficacy endpoint (SPID48) could not establish the non-inferiority of TA-ER to TA-IR. However, a post hoc analysis with a re-defined non-inferiority margin did demonstrate the non-inferiority of TA-ER to TA-IR. No statistically significant difference in SPID at 6, 12, or 24 hours was observed between the TA-ER and TA-IR groups. Similarly, analysis of TOTPAR showed that there were no significant differences between groups at any on-therapy time point, and SPID + TOTPAR at 6 and 48 hours were similar among groups. There was no difference in the mean frequency or dosage of rescue medication required by both groups, and the majority of patients in both the TA-ER and TA-IR groups rated their pain improvement as 'much' or 'somewhat better'. The overall incidence of ≥1 AEs was similar among the TA-ER (88.8%) and TA-IR (89.5%) groups. The most commonly

Bioactive Glass Nanoparticles as a New Delivery System for Sustained 5-Fluorouracil Release: Characterization and Evaluation of Drug Release Mechanism

Directory of Open Access Journals (Sweden)

Abeer M. El-Kady

2015-01-01

Full Text Available Bioactive glass nanoparticles were synthesized and tested for the first time as a new delivery system for sustained 5-fluorouracil (5-FU release. They were characterized by TEM, DTA, TGA, and FT-IR. The porosity % and specific surface area of glass nanoparticles were 85.59% and 378.36 m2/g, respectively. The in vitro bioactivity evaluation confirmed that bioactive glass disks prepared from these nanoparticles could induce hydroxyapatite layer over their surfaces in simulated body fluid. The in vitro drug release experiment indicated that glass nanoparticles could serve as long-term local delivery vehicles for sustained 5-FU release. The release profile of 5-FU showed an initial fast release stage followed by a second stage of slower release. The initial burst release of 5-FU in the first day was about 23% (28.92 mg·L−1 of the total amount of loaded 5-FU, while the final cumulative percentage of the 5-FU released after 32 days was about 45.6% (57.31 mg·L−1 of the total amount of loaded 5-FU. The application of different mathematical models indicated that 5-FU was released by diffusion controlled mechanism and suggested that its release rate was dependent on glass particles dissolution, changes of surface area as well as diameter of glass particles, and concentration of loaded drug.

Effect of Atmospheric Conditions on Coverage of Fogger Applications in a Desert Surface Boundary Layer

Science.gov (United States)

2012-01-01

Salyani, T. W. Walker, M. Farooq ABSTRACT. Near-ground aerosol fogs were applied in the Chihuahua Desert of New Mexico, which has widely spaced, low...Approved for public release; distribution unlimited 13. SUPPLEMENTARY NOTES 14. ABSTRACT Near-ground aerosol fogs were applied in the Chihuahua Desert of...1.6° surrounded by sparse Chihuahua De- sert vegetation approximately 2 m tall (fig. 1). The vegeta- tion was primarily mesquite and creosote bushes

Effect of Xenon Anesthesia Compared to Sevoflurane and Total Intravenous Anesthesia for Coronary Artery Bypass Graft Surgery on Postoperative Cardiac Troponin Release: An International, Multicenter, Phase 3, Single-blinded, Randomized Noninferiority Trial.

Science.gov (United States)

Hofland, Jan; Ouattara, Alexandre; Fellahi, Jean-Luc; Gruenewald, Matthias; Hazebroucq, Jean; Ecoffey, Claude; Joseph, Pierre; Heringlake, Matthias; Steib, Annick; Coburn, Mark; Amour, Julien; Rozec, Bertrand; Liefde, Inge de; Meybohm, Patrick; Preckel, Benedikt; Hanouz, Jean-Luc; Tritapepe, Luigi; Tonner, Peter; Benhaoua, Hamina; Roesner, Jan Patrick; Bein, Berthold; Hanouz, Luc; Tenbrinck, Rob; Bogers, Ad J J C; Mik, Bert G; Coiffic, Alain; Renner, Jochen; Steinfath, Markus; Francksen, Helga; Broch, Ole; Haneya, Assad; Schaller, Manuella; Guinet, Patrick; Daviet, Lauren; Brianchon, Corinne; Rosier, Sebastien; Lehot, Jean-Jacques; Paarmann, Hauke; Schön, Julika; Hanke, Thorsten; Ettel, Joachym; Olsson, Silke; Klotz, Stefan; Samet, Amir; Laurinenas, Giedrius; Thibaud, Adrien; Cristinar, Mircea; Collanges, Olivier; Levy, François; Rossaint, Rolf; Stevanovic, Ana; Schaelte, Gereon; Stoppe, Christian; Hamou, Nora Ait; Hariri, Sarah; Quessard, Astrid; Carillion, Aude; Morin, Hélène; Silleran, Jacqueline; Robert, David; Crouzet, Anne-Sophie; Zacharowski, Kai; Reyher, Christian; Iken, Sonja; Weber, Nina C; Hollmann, Marcus; Eberl, Susanne; Carriero, Giovanni; Collacchi, Daria; Di Persio, Alessandra; Fourcade, Olivier; Bergt, Stefan; Alms, Angela

2017-12-01

Ischemic myocardial damage accompanying coronary artery bypass graft surgery remains a clinical challenge. We investigated whether xenon anesthesia could limit myocardial damage in coronary artery bypass graft surgery patients, as has been reported for animal ischemia models. In 17 university hospitals in France, Germany, Italy, and The Netherlands, low-risk elective, on-pump coronary artery bypass graft surgery patients were randomized to receive xenon, sevoflurane, or propofol-based total intravenous anesthesia for anesthesia maintenance. The primary outcome was the cardiac troponin I concentration in the blood 24 h postsurgery. The noninferiority margin for the mean difference in cardiac troponin I release between the xenon and sevoflurane groups was less than 0.15 ng/ml. Secondary outcomes were the safety and feasibility of xenon anesthesia. The first patient included at each center received xenon anesthesia for practical reasons. For all other patients, anesthesia maintenance was randomized (intention-to-treat: n = 492; per-protocol/without major protocol deviation: n = 446). Median 24-h postoperative cardiac troponin I concentrations (ng/ml [interquartile range]) were 1.14 [0.76 to 2.10] with xenon, 1.30 [0.78 to 2.67] with sevoflurane, and 1.48 [0.94 to 2.78] with total intravenous anesthesia [per-protocol]). The mean difference in cardiac troponin I release between xenon and sevoflurane was -0.09 ng/ml (95% CI, -0.30 to 0.11; per-protocol: P = 0.02). Postoperative cardiac troponin I release was significantly less with xenon than with total intravenous anesthesia (intention-to-treat: P = 0.05; per-protocol: P = 0.02). Perioperative variables and postoperative outcomes were comparable across all groups, with no safety concerns. In postoperative cardiac troponin I release, xenon was noninferior to sevoflurane in low-risk, on-pump coronary artery bypass graft surgery patients. Only with xenon was cardiac troponin I release less than with total intravenous

2015 TRI National Analysis: Toxics Release Inventory Releases at Various Summary Levels

Science.gov (United States)

The TRI National Analysis is EPA's annual interpretation of TRI data at various summary levels. It highlights how toxic chemical wastes were managed, where toxic chemicals were released and how the 2015 TRI data compare to data from previous years. This dataset reports US state, county, large aquatic ecosystem, metro/micropolitan statistical area, and facility level statistics from 2015 TRI releases, including information on: number of 2015 TRI facilities in the geographic area and their releases (total, water, air, land); population information, including populations living within 1 mile of TRI facilities (total, minority, in poverty); and Risk Screening Environmental Indicators (RSEI) model related pounds, toxicity-weighted pounds, and RSEI score. The source of administrative boundary data is the 2013 cartographic boundary shapefiles. Location of facilities is provided by EPA's Facility Registry Service (FRS). Large Aquatic Ecosystems boundaries were dissolved from the hydrologic unit boundaries and codes for the United States, Puerto Rico, and the U.S. Virgin Islands. It was revised for inclusion in the National Atlas of the United States of America (November 2002), and updated to match the streams file created by the USGS National Mapping Division (NMD) for the National Atlas of the United States of America.

Consequences of severe radioactive releases to Nordic Marine environment

DEFF Research Database (Denmark)

Iosjpe, M.; Isaksson, M.; Joensen, H.P.

- or minor – radioactive releases to Nordic marine environment. As a reference, the release amounts from a 3000 MWth reactor size were used. Based on source term analyses, the chosen release fractions in the study were: iodine 20% (of the total core inventory), caesium 10%, tellurium 10%, strontium 0...

Field evaluation of indoor thermal fog and ultra-low volume applications for control of Aedes aegypti, in Thailand

Science.gov (United States)

Efficacies of a hand-held thermal fogger (PatriotTM) and hand-held Ultra-low volume (ULV) sprayer (TwisterTM) with combinations of two different adulticides and an insect growth regulator (pyriproxyfen) were field assessed and compared for their impact on reducing dengue vector populations in Thaila...

IT release management a hands-on guide

CERN Document Server

Howard, Dave

2011-01-01

When implemented correctly, release management can help ensure that quality is integrated throughout the development, implementation, and delivery of services, applications, and infrastructure. This holistic, total cost of ownership approach allows for higher levels of system availability, is more cost effective to maintain, and increases overall stability, maintainability, and reliability. Filled with practical insights, IT Release Management: A Hands-on Guide clearly illustrates the effective implementation of a release process in the real world. It examines the similarities and differences

Release of cadmium, copper and lead from urban soils of Copenhagen

International Nuclear Information System (INIS)

Li, Lijun; Holm, Peter E.; Marcussen, Helle; Bruun Hansen, Hans Christian

2014-01-01

We studied the bonding and release kinetics of Cd, Cu and Pb from different soils in the older metropolitan area of Copenhagen. Total Cd, Cu and Pb concentrations were elevated 5–27 times in the urban soils compared to an agricultural reference soil, with Cd and Pb in mainly mobilisable pools and Cu in strongly bound pools. The soils were subjected to accelerated leaching studies in Ca(NO 3 ) 2 or HNO 3 solutions resulting in release up to 78, 18 and 15% of total Cd, Cu and Pb soil concentrations over a period of 15 weeks. The relative initial Cd and Pb release rates increased 10 fold when pH decreased 2 and 3 units, respectively, while increases in Cu release rates were only seen at pH below 4. The total leachable Cu and Pb pools were higher in urban soils compared the agricultural reference soil but not for Cd. - Highlights: • Total Cd, Cu and Pb concentrations were elevated 5–27 times in the urban soils. • Cd and Pb are potentially available from acid leachable and reducible soil fractions. • Up to 78, 18 and 15% of total soil Cd, Cu and Pb could be acid leached. • Initial Cd and Pb release rates increase 10 fold with pH decrease of 2 and 3 units. • The mobility of Cu and Pb were higher in urban compared to agricultural soils. - Cadmium, Cu and Pb were studied in Copenhagen urban soils. These soils show similar initial relative release rates but higher total mobility of Cu and Pb compared to a reference soil

PCDD/PCDF release inventories

Energy Technology Data Exchange (ETDEWEB)

Fiedler, H. [UNEP Chemicals, Chatelaine (Switzerland)

2004-09-15

The Stockholm Convention on Persistent Organic Pollutants (POPs) entered into force on 17 May 2004 with 50 Parties. In May 2004, 59 countries had ratified or acceded the Convention. The objective of the Convention is ''to protect human health and the environment from persistent organic pollutants''. For intentionally produced POPs, e.g., pesticides and industrial chemicals such as hexachlorobenzene and polychlorinated biphenyls, this will be achieved by stop of production and use. For unintentionally generated POPs, such as polychlorinated dibenzo-pdioxins (PCDD) and polychlorinated dibenzofurans (PCDF), measures have to be taken to ''reduce the total releases derived from anthropogenic sources''; the final goal is ultimate elimination, where feasible. Under the Convention, Parties have to establish and maintain release inventories to prove the continuous release reduction. Since many countries do not have the technical and financial capacity to measure all releases from all potential PCDD/PCDF sources, UNEP Chemicals has developed the ''Standardized Toolkit for the Identification of Quantification of Dioxin and Furan Releases'' (''Toolkit'' for short), a methodology to estimate annual releases from a number of sources. With this methodology, annual releases can be estimated by multiplying process-specific default emission factors provided in the Toolkit with national activity data. At the seventh session of the Intergovernmental Negotiating Committee, the Toolkit was recommended to be used by countries when reporting national release data to the Conference of the Parties. The Toolkit is especially used by developing countries and countries with economies in transition where no measured data are available. Results from Uruguay, Thailand, Jordan, Philippines, and Brunei Darussalam have been published.

Activated human neutrophils release hepatocyte growth factor/scatter factor.

LENUS (Irish Health Repository)

McCourt, M

2012-02-03

BACKGROUND: Hepatocyte growth factor or scatter factor (HGF\\/SF) is a pleiotropic cytokine that has potent angiogenic properties. We have previously demonstrated that neutrophils (PMN) are directly angiogenic by releasing vascular endothelial growth factor (VEGF). We hypothesized that the acute inflammatory response can stimulate PMN to release HGF. AIMS: To examine the effects of inflammatory mediators on PMN HGF release and the effect of recombinant human HGF (rhHGF) on PMN adhesion receptor expression and PMN VEGF release. METHODS: In the first experiment, PMN were isolated from healthy volunteers and stimulated with tumour necrosis factor-alpha (TNF-alpha), lipopolysaccharide (LPS), interleukin-8 (IL-8), and formyl methionyl-leucyl-phenylalanine (fMLP). Culture supernatants were assayed for HGF using ELISA. In the second experiment, PMN were lysed to measure total HGF release and HGF expression in the PMN was detected by Western immunoblotting. Finally, PMN were stimulated with rhHGF. PMN CD 11a, CD 11b, and CD 18 receptor expression and VEGF release was measured using flow cytometry and ELISA respectively. RESULTS: TNF-alpha, LPS and fMLP stimulation resulted in significantly increased release of PMN HGF (755+\\/-216, 484+\\/-221 and 565+\\/-278 pg\\/ml, respectively) compared to controls (118+\\/-42 pg\\/ml). IL-8 had no effect. Total HGF release following cell lysis and Western blot suggests that HGF is released from intracellular stores. Recombinant human HGF did not alter PMN adhesion receptor expression and had no effect on PMN VEGF release. CONCLUSIONS: This study demonstrates that pro-inflammatory mediators can stimulate HGF release from a PMN intracellular store and that activated PMN in addition to secreting VEGF have further angiogenic potential by releasing HGF.

Effects of compost age on the release of nutrients

Directory of Open Access Journals (Sweden)

Bilal B. Al-Bataina

2016-09-01

Full Text Available Composted organic materials are applied to help restore disturbed soils, speed revegetation, and control erosion; these changes are generally beneficial for stormwater quality. Ensuring that nutrient release from compost is adequate for plant needs without degrading stormwater quality is important since composts release nitrogen at variable rates (1–3% of total N/yr and the leaching process can extend for many years. The aim of this work was to understand the effect of compost age on the extent and rates of nitrogen release by conducting detailed rainfall simulation studies of one compost type at three different ages. Models describing temporal changes in nitrogen release to runoff during a single storm and across multiple storms were developed and applied to the runoff data. Nitrogen content (% and bulk density of compost increased with the increase in compost age and total nitrogen release decreased with increasing compost age. The three rain simulations (storms performed on each of the three compost ages show that nitrogen release declined each day of the repeated daily storms. A first-order kinetic model was used to estimate the amount of nitrogen remaining on compost after several storms.

Results of Lateral Retinacular Release Plus Circumpatellar Electrocautery in Total Knee Arthroplasty without Patellar Resurfacing.

Science.gov (United States)

Wang, Yong; Sun, Jun-Ying; Zha, Guo-Chun

2017-03-01

Anterior knee pain (AKP) is integral to the overall success of total knee arthroplasty (TKA) without patellar resurfacing. Numerous studies have evaluated various factors that may contribute to AKP, including patellofemoral design, surgical technique, characteristics of the patient, and degree of chondromalacia. This study aims to explore whether patients who received lateral retinacular release (LRR) plus circumpatellar electrocautery (CE) in TKA attain a low incidence of AKP and whether the LRR plus CE increases postoperative complications. Between February 2001 and February 2009, all patients undergoing TKA without patellar resurfacing and LRR plus CE were evaluated. In total, 286 TKAs in 259 (88.7%) patients were available for assessment, with a mean of 9.3 ± 2.5 years (range: 6-14 years) after the index TKA. The patients were evaluated with a VAS and the Kujala patellofemoral score (KPS) for AKP and the Knee Society's clinical scoring system (KSS) for the clinical function. Satisfaction and LRR-related complications were also assessed. The mean KPS and KSS improved from 45.2 ± 12.9 and 75.4 ± 26.8 points preoperatively to 82.8 ± 10.0 and 151.6 ± 17.3 points at the final follow-up ( p  < 0.001), respectively. Subjectively, 5.6% (16 of 286) of patients suffered from AKP and 88.1% (252 of 286) were satisfied or very satisfied. Postoperative complications occurred in 15 (5.2%) patients, but these complications were mild and did not require reoperation. None of patients exhibited aseptic and septic prosthesis loosening and required revision surgery in the final follow-up. LRR plus CE appears to be a reasonable option in TKA without patellar resurfacing. It may achieve adequate mid-term results, with a low incidence of AKP and postoperative complications.The level of evidence of the study is therapeutic level IV. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

Calculation of tritium release from reactor's stack

International Nuclear Information System (INIS)

Akhadi, M.

1996-01-01

Method for calculation of tritium release from nuclear to environment has been discussed. Part of gas effluent contain tritium in form of HTO vapor released from reactor's stack was sampled using silica-gel. The silica-gel was put in the water to withdraw HTO vapor absorbed by silica-gel. Tritium concentration in the water was measured by liquid scintillation counter of Aloka LSC-703. Tritium concentration in the gas effluent and total release of tritium from reactor's stack during certain interval time were calculated using simple mathematic formula. This method has examined for calculation of tritium release from JRR-3M's stack of JAERI, Japan. From the calculation it was obtained the value of tritium release as much as 4.63 x 10 11 Bq during one month. (author)

Synthesis and release of luteinizing hormone in vitro: manipulations of Ca2+ environment

International Nuclear Information System (INIS)

Liu, T.C.; Jackson, G.L.

1985-01-01

The authors determined if luteinizing hormone (LH) synthesis is Ca2+ dependent and coupled to LH release. They monitored LH synthesis when LH release was stimulated either by specific [gonadotropin-releasing hormone (GnRH)] or nonspecific stimuli (50 mM K+ and 2 or 20 microM Ca2+ ionophore A23187) and inhibited by Ca2+-reduced medium. LH synthesis was estimated by measuring incorporation of [ 3 H]glucosamine (glycosylation) and [ 14 C]alanine (translation) into total (cell and medium) immunoprecipitable LH by cultured rat anterior pituitary cells. Both GnRH (1 nM) and 50 mM K+ significantly stimulated LH release and glycosylation, but had no effect on LH translation. A23187 also stimulated LH release, but significantly depressed glycosylation of LH and total protein and [ 14 C]alanine uptake. Deletion of Ca2+ from the medium depressed both GnRH-induced LH release and glycosylation. Addition of 0.1 mM EGTA to Ca2+-free medium not only inhibited GnRH-induced release and glycosylation of LH but also uptake of precursors and glycosylation and translation of total protein. Thus, glycosylation and release of LH are Ca2+ dependent. Whether parallel changes in LH release and glycosylation reflect a cause and effect relationship remains to be determined

Limited Releases of Krsko NPP

International Nuclear Information System (INIS)

Breznik, B.; Kovac, A.

2001-01-01

Full text: Krsko Nuclear Power Plant is about 700 MW Pressurised Water Reactor plant located in Slovenia close to the border with Croatia. The authorised limit for the radioactive releases is basically set to 50 μSv effective dose per year to the members of the public. There is also additional limitation of total activities released in a year and concentration. The poster presents the effluents of the year 2000 and evaluated dose referring to the limits and to the natural and other sources of radiation around the plant. (author)

Dynamic Model for the Stocks and Release Flows of Engineered Nanomaterials.

Science.gov (United States)

Song, Runsheng; Qin, Yuwei; Suh, Sangwon; Keller, Arturo A

2017-11-07

Most existing life-cycle release models for engineered nanomaterials (ENM) are static, ignoring the dynamics of stock and flows of ENMs. Our model, nanoRelease, estimates the annual releases of ENMs from manufacturing, use, and disposal of a product explicitly taking stock and flow dynamics into account. Given the variabilities in key parameters (e.g., service life of products and annual release rate during use) nanoRelease is designed as a stochastic model. We apply nanoRelease to three ENMs (TiO 2 , SiO 2 and FeO x ) used in paints and coatings through seven product applications, including construction and building, household and furniture, and automotive for the period from 2000 to 2020 using production volume and market projection information. We also consider model uncertainties using Monte Carlo simulation. Compared with 2016, the total annual releases of ENMs in 2020 will increase by 34-40%, and the stock will increase by 28-34%. The fraction of the end-of-life release among total release flows will increase from 11% in 2002 to 43% in 2020. As compared to static models, our dynamic model predicts about an order of magnitude lower values for the amount of ENM released from this sector in the near-term while stock continues to build up in the system.

Release of Gentamicin and Vancomycin from Preformed Spacers in Infected Total Hip Arthroplasties: Measurement of Concentrations and Inhibitory Activity in Patients’ Drainage Fluids and Serum

Directory of Open Access Journals (Sweden)

Dario Regis

2013-01-01

Full Text Available Gentamicin (G and vancomycin (V concentrations in drainage fluids obtained from patients during the first 24 hours after implantation of antibiotic-loaded polymethylmethacrylate (PMMA spacers in two-stage revision of infected total hip arthroplasty were studied. The inhibitory activity of drainage fluids against different multiresistant clinical isolates was investigated as well. Seven hips were treated by implantation of industrial G-loaded spacers. Vancomycin was added by manually mixing with PMMA bone cement. Serum and drainage fluid samples were collected 1, 4, and 24 hours after spacer implantation. Antibiotics concentrations and drains bactericidal titer of combination were determined against multiresistant staphylococcal strains. The release of G and V from PMMA cement at the site of infection was prompt and effective. Serum levels were below the limit of detection. The local release kinetics of G and V from PMMA cement was similar, exerting a pronounced, combined inhibitory effect in the implant site. The inhibitory activity of drainage fluids showed substantial intersubject variability related to antibiotic concentrations and differed according to the pathogens tested. Gentamicin and vancomycin were released from temporary hip spacers at bactericidal concentrations, and their use in combination exerted strong inhibition against methicillin-resistant S. aureus and Coagulase Negative Staphylococci strains.

GEWEX SRB Shortwave Release 4

Science.gov (United States)

Cox, S. J.; Stackhouse, P. W., Jr.; Mikovitz, J. C.; Zhang, T.

2017-12-01

The NASA/GEWEX Surface Radiation Budget (SRB) project produces shortwave and longwave surface and top of atmosphere radiative fluxes for the 1983-near present time period. Spatial resolution is 1 degree. The new Release 4 uses the newly processed ISCCP HXS product as its primary input for cloud and radiance data. The ninefold increase in pixel number compared to the previous ISCCP DX allows finer gradations in cloud fraction in each grid box. It will also allow higher spatial resolutions (0.5 degree) in future releases. In addition to the input data improvements, several important algorithm improvements have been made since Release 3. These include recalculated atmospheric transmissivities and reflectivities yielding a less transmissive atmosphere. The calculations also include variable aerosol composition, allowing for the use of a detailed aerosol history from the Max Planck Institut Aerosol Climatology (MAC). Ocean albedo and snow/ice albedo are also improved from Release 3. Total solar irradiance is now variable, averaging 1361 Wm-2. Water vapor is taken from ISCCP's nnHIRS product. Results from GSW Release 4 are presented and analyzed. Early comparison to surface measurements show improved agreement.

In vitro studies of copper release from powder particles in synthetic biological media

International Nuclear Information System (INIS)

Midander, Klara; Wallinder, Inger Odnevall; Leygraf, Christofer

2007-01-01

The aim of this paper is to provide quantitative data on copper release from powder particles of different copper materials, including artificial copper patina, Cu 2 O and metallic Cu, when exposed to different synthetic biological media to simulate an inhalation scenario and/or skin contact. Generated data may contribute in risk assessment of potential health effects following exposure to and handling of various copper materials. All tests were performed in vitro to determine total copper concentrations, release rates of total copper, and to elucidate its time-dependence. The copper release process was interpreted in terms of specific surface area, surface morphology-, and composition. All powder materials show a time-dependent release process with total copper release rates less than 3 μg/cm 2 per hour at steady state conditions, for all media investigated. The importance of using relevant test media when simulating different interstitial lung conditions and difficulties encountered when comparing powder particles of essentially different properties are thoroughly discussed. - Copper release rates from particles are essential to assess potential health aspects

Applying a crop-tree release in small-sawtimber white oak stands

Science.gov (United States)

Jeffrey W Stringer; Gary W. Miller; Robert F. Wittwer; Robert F. Wittwer

1988-01-01

Small-sawtimber white oak crop trees in Kentucky were released by a crown-touching technique. In two cutting treatments, 20 and 34 crop trees were released per acre at a total cost of $35 and $42, respectively. Both treatments yielded commercial volumes of cut material. Total mean merchantable volume (> 5.0 inches d.b.h.) in cut trees was 693 cubic feet/acre, with...

The release of silver nanoparticles from commercial toothbrushes

DEFF Research Database (Denmark)

Mackevica, Aiga; Olsson, Mikael Emil; Hansen, Steffen Foss

2017-01-01

The use of silver nanoparticles (NPs) in commercial products has become increasingly common in the past decade, mostly due to their antimicrobial properties. Using Ag NP-containing articles may lead to particle release, which raises concern of human and environmental safety. The published...... literature addressing particle release is scarce, especially when it comes to quantifying exposure to NPs specifically. In this study, we have experimentally investigated the release of total Ag and Ag NP from commercially available toothbrushes i.e. biodegradable toothbrushes for adults and toothbrushes...

Nitrate capture and slow release in biochar amended compost and soil.

Directory of Open Access Journals (Sweden)

Nikolas Hagemann

Full Text Available Slow release of nitrate by charred organic matter used as a soil amendment (i.e. biochar was recently suggested as potential mechanism of nutrient delivery to plants which may explain some agronomic benefits of biochar. So far, isolated soil-aged and composted biochar particles were shown to release considerable amounts of nitrate only in extended (>1 h extractions ("slow release". In this study, we quantified nitrate and ammonium release by biochar-amended soil and compost during up to 167 h of repeated extractions in up to six consecutive steps to determine the effect of biochar on the overall mineral nitrogen retention. We used composts produced from mixed manures amended with three contrasting biochars prior to aerobic composting and a loamy soil that was amended with biochar three years prior to analysis and compared both to non-biochar amended controls. Composts were extracted with 2 M KCl at 22°C and 65°C, after sterilization, after treatment with H2O2, after removing biochar particles or without any modification. Soils were extracted with 2 M KCl at 22°C. Ammonium was continuously released during the extractions, independent of biochar amendment and is probably the result of abiotic ammonification. For the pure compost, nitrate extraction was complete after 1 h, while from biochar-amended composts, up to 30% of total nitrate extracted was only released during subsequent extraction steps. The loamy soil released 70% of its total nitrate amount in subsequent extractions, the biochar-amended soil 58%. However, biochar amendment doubled the amount of total extractable nitrate. Thus, biochar nitrate capture can be a relevant contribution to the overall nitrate retention in agroecosystems. Our results also indicate that the total nitrate amount in biochar amended soils and composts may frequently be underestimated. Furthermore, biochars could prevent nitrate loss from agroecosystems and may be developed into slow-release fertilizers to

Evaluation of blood loss after early or late release of ischemia in patients undergoing total knee replacement Avaliação da perda sanguínea após a liberação precoce ou tardia da isquemia em pacientes submetidos à artroplastia total do joelho

Directory of Open Access Journals (Sweden)

Marcos George de Souza Leão

2013-04-01

Full Text Available OBJECTIVE: compare blood loss in 40 patients underwent to unilateral total knee replacement with the release of ischemia before and after skin closure and compressive dressing. METHODS: in a prospective randomized study, in 40 patients underwent to total knee replacement, dividing then into two groups: group A in which the ischemia was released before skin closure, allowing bleeding control and group B where the ischemia was released after skin suture and pressure dressing. We compared the results of laboratory tests of serum hemoglobin before surgery and 48 hours postoperatively, the blood volume contained in vacuum suction drain and the transfusions that was necessary. RESULTS: As a result, the post operative serum hemoglobin levels had a mean decrease of 3.57 g/dL in group A and 4.24 g/dL in group B with an average of 0.67g/dL difference between them, statistically insignificant.The observed mean drainage, in the vacuum drain, were 705 mL in group A and 700 mL in group B. The 5ml difference between medians was considered statistically insignificant. The number of patients who received transfusions was four patients in both groups and all received two units of red blood cells. CONCLUSION: the post operative serum hemoglobin levels, as well as the need of blood transfusion, in the patient underwent to total knee replacement, where the ischemia was released before wound closure, has no statistical effect in comparison with patients where the sutures and bandages were done after the ischemia release. Level of Evidence IB - Individual randomized controlled trial with narrow confidence interval. OBJETIVO: Avaliar comparativamente a perda sanguínea em pacientes submetidos à artroplastia total do joelho, com liberação da isquemia antes e após suturas e curativo compressivo. MÉTODOS: Fez-se um estudo prospectivo randomizado em 40 pacientes submetidos à artroplastia total do joelho divididos em dois grupos. No primeiro grupo a isquemia foi

The SDSS-III DR12 MARVELS radial velocity data release: the first data release from the multiple object Doppler exoplanet survey

Science.gov (United States)

Ge, Jian; Thomas, Neil B.; Li, Rui; Senan Seieroe Grieves, Nolan; Ma, Bo; de Lee, Nathan M.; Lee, Brian C.; Liu, Jian; Bolton, Adam S.; Thakar, Aniruddha R.; Weaver, Benjamin; SDSS-Iii Marvels Team

2015-01-01

We present the first data release from the SDSS-III Multi-object APO Radial Velocity Exoplanet Large-area Survey (MARVELS) through the SDSS-III DR12. The data include 181,198 radial velocity (RV) measurements for a total of 5520 different FGK stars with V~7.6-12, of which more than 80% are dwarfs and subdwarfs while remainders are GK giants, among a total of 92 fields nearly randomly spread out over the entire northern sky taken with a 60-object MARVELS dispersed fixed-delay interferometer instrument over four years (2008-2012). There were 55 fields with a total of 3300 FGK stars which had 14 or more observations over about 2-year survey window. The median number of observations for these plates is 27 RV measurements. This represents the largest homogeneous sample of precision RV measurements of relatively bright stars. In this first released data, a total of 18 giant planet candidates, 16 brown dwarfs, and over 500 binaries with additional 96 targets having RV variability indicative of a giant planet companion are reported. The released data were produced by the MARVELS finalized 1D pipeline. We will also report preliminary statistical results from the MARVELS 2D data pipeline which has produced a median RV precision of ~30 m/s for stable stars.

Building Adjustable Pre-storm Reservoir Flood-control Release Rules

Science.gov (United States)

Yang, Shun-Nien; Chang, Li-Chiu; Chang, Fi-John; Hsieh, Cheng-Daw

2017-04-01

Typhoons hit Taiwan several times every year, which could cause serious flood disasters. Because mountainous terrains and steep landforms can rapidly accelerate the speed of flood flow during typhoon events, rivers cannot be a stable source of water supply. Reservoirs become the most effective floodwater storage facilities for alleviating flood damages in Taiwan. The pre-storm flood-control release can significantly increase reservoir storage capacity available to store floodwaters for reducing downstream flood damage, while the uncertainties of total forecasted rainfalls are very high in different stages of an oncoming typhoon, which may cause the risk of water shortage in the future. This study proposes adjustable pre-storm reservoir flood-control release rules in three designed operating stages with various hydrological conditions in the Feitsui Reservoir, a pivot reservoir for water supply to Taipei metropolitan in Taiwan, not only to reduce the risk of reservoir flood control and downstream flooding but also to consider water supply. The three operating stages before an oncoming typhoon are defined upon the timings when: (1) typhoon news is issued (3-7days before typhoon hit); (2) the sea warning is issued (2-4 days before typhoon hit); and (3) the land warning is issued (1-2 days before typhoon hit). We simulate 95 historical typhoon events with 3000 initial water levels and build some pre-storm flood-control release rules to adjust the amount of pre-release based on the total forecasted rainfalls at different operating stages. A great number of simulations (68.4 millions) are conducted to extract their major consequences and then build the adjustable pre-storm reservoir flood-control release rules. Accordingly, given a total forecasted rainfall and a water level, reservoir decision makers can easily identify the corresponding rule to tell the amount of pre-release in any stage. The results show that the proposed adjustable pre-release rules can effectively

The release of fission products from uranium metal: a review

International Nuclear Information System (INIS)

Minshall, P.C.

1989-03-01

The literature on the release of fission products as gaseous species from irradiated uranium metal in oxidising atmospheres has been reviewed. Release of actinides and of fission products as spalled particulate were not considered. Data is given on the release in air, carbon dioxide, steam and mixtures of steam and air. The majority of data discussed lie between 800 and 1200 0 C though some results for xenon, krypton and iodine releases below 800 0 C are given. Two measures of fission product release are discussed: the release fraction, F(tot), which is the ratio of the total release to the initial inventory, and the fractional release, F(ox), which is the fraction released from the oxidised metal. The effect of burn-up, atmosphere and temperature on F(tot) and F(ox) is examined and the conditions under which the release fraction, F(tot) is proportional to the extent of oxidation discussed. (author)

Expressions for the Total Yaw Angle

Science.gov (United States)

2016-09-01

1. Introduction 1 2. Mathematical Notation 1 3. Total Yaw Expression Derivations 2 3.1 First Derivation 2 3.2 Second Derivation 4 3.3 Other...4 iv Approved for public release; distribution is unlimited. 1. Introduction The total yaw angle, γt , of a ballistic projectile is... elevation angles from spherical coordinates.∗ We again place point A at the end point of V. Now imagine a plane parallel to the y-z plane that includes

Fission Fragment Mass Distributions and Total Kinetic Energy Release of 235-Uranium and 238-Uranium in Neutron-Induced Fission at Intermediate and Fast Neutron Energies

Energy Technology Data Exchange (ETDEWEB)

Duke, Dana Lynn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-11-12

This Ph.D. dissertation describes a measurement of the change in mass distributions and average total kinetic energy (TKE) release with increasing incident neutron energy for fission of ²³⁵U and ²³⁸U. Although fission was discovered over seventy-five years ago, open questions remain about the physics of the fission process. The energy of the incident neutron, En, changes the division of energy release in the resulting fission fragments, however, the details of energy partitioning remain ambiguous because the nucleus is a many-body quantum system. Creating a full theoretical model is difficult and experimental data to validate existing models are lacking. Additional fission measurements will lead to higher-quality models of the fission process, therefore improving applications such as the development of next-generation nuclear reactors and defense. This work also paves the way for precision experiments such as the Time Projection Chamber (TPC) for fission cross section measurements and the Spectrometer for Ion Determination in Fission (SPIDER) for precision mass yields.

Model-based computer-aided design for controlled release of pesticides

DEFF Research Database (Denmark)

Muro Sunè, Nuria; Gani, Rafiqul; Bell, G.

2005-01-01

In the field of controlled release technology for pesticides or active ingredients (AI), models that can predict its delivery during application are important for purposes of design and marketing of the pesticide product. Appropriate models for the controlled release of pesticides, if available, ...... extended models have been developed and implemented into a computer-aided system. The total model consisting of the property models embedded into the release models are then employed to study the release of different combinations of AIs and polymer-based microcapsules.......In the field of controlled release technology for pesticides or active ingredients (AI), models that can predict its delivery during application are important for purposes of design and marketing of the pesticide product. Appropriate models for the controlled release of pesticides, if available...

Stereoselectivity of presynaptic autoreceptors modulating dopamine release

International Nuclear Information System (INIS)

Arbilla, S.; Langer, S.Z.

1981-01-01

The effects of the (R)- and (S)-enantiomers of sulpiride and butaclamol were studied on the spontaneous and field stimulation-evoked release of total radioactivity from slices of rabbit caudate nucleus prelabelled with [ 3 H]dopamine. (S)-Sulpiride in concentrations ranging from 0.01-1μM enhanced the electrically evoked release of [ 3 H]dopamine while (R)-sulpiride was 10 times less potent than (S)-sulpiride. Exposure to (S)-butaclamol (0.1-1 μM) but not to (R)-butaclamol (0.1-10μM) enhanced the field-stimulated release of [ 3 H]dopamine. The facilitatory effects of (S)- and (R)-sulpiride and (S)-butaclamol on the stimulated release of the labelled neurotransmitter were observed under conditions in which these drugs did not modify the spontaneous outflow of radioactivity. Only the active enantiomers of sulpiride and butaclamol antagonized the inhibition by apomorphine (1μM) of the stimulated release of [ 3 H]dopamine. Our results indicate that the presynaptic inhibitory dopamine autoreceptors modulating the stimulation-evoked release of [ 3 H]dopamine in the caudate nucleus are, like the classical postsynaptic dopamine receptors, chemically stereoselective. (Auth.)

Preparation and Optimization of Immediate Release/Sustained Release Bilayered Tablets of Loxoprofen Using Box-Behnken Design.

Science.gov (United States)

Tak, Jin Wook; Gupta, Biki; Thapa, Raj Kumar; Woo, Kyu Bong; Kim, Sung Yub; Go, Toe Gyeong; Choi, Yongjoo; Choi, Ju Yeon; Jeong, Jee-Heon; Choi, Han-Gon; Yong, Chul Soon; Kim, Jong Oh

2017-05-01

The aim of our current study was to characterize and optimize loxoprofen immediate release (IR)/sustained release (SR) tablet utilizing a three-factor, three-level Box-Behnken design (BBD) combined with a desirability function. The independent factors included ratio of drug in the IR layer to total drug (X 1 ), ratio of HPMC to drug in the SR layer (X 2 ), and ratio of Eudragit RL PO to drug in the SR layer (X 3 ). The dependent variables assessed were % drug released in distilled water at 30 min (Y 1 ), % drug released in pH 1.2 at 2 h (Y 2 ), and % drug released in pH 6.8 at 12 h (Y 3 ). The responses were fitted to suitable models and statistical validation was performed using analysis of variance. In addition, response surface graphs and contour plots were constructed to determine the effects of different factor level combinations on the responses. The optimized loxoprofen IR/SR tablets were successfully prepared with the determined amounts of ingredients that showed close agreement in the predicted and experimental values of tablet characterization and drug dissolution profile. Therefore, BBD can be utilized for successful optimization of loxoprofen IR/SR tablet, which can be regarded as a suitable substitute for the current marketed formulations.

Nitric Oxide-Releasing Silica Nanoparticle-Doped Polyurethane Electrospun Fibers

Science.gov (United States)

Koh, Ahyeon; Carpenter, Alexis W.; Slomberg, Danielle L.; Schoenfisch, Mark H.

2013-01-01

Electrospun polyurethane fibers doped with nitric oxide (NO)-releasing silica particles are presented as novel macromolecular scaffolds with prolonged NO-release and high porosity. Fiber diameter (119–614 nm) and mechanical strength (1.7–34.5 MPa of modulus) were varied by altering polyurethane type and concentration, as well as the NO-releasing particle composition, size, and concentration. The resulting NO-releasing electrospun nanofibers exhibited ~83% porosity with flexible plastic or elastomeric behavior. The use of N-diazeniumdiolate- or S-nitrosothiol-modified particles yielded scaffolds exhibiting a wide range of NO release totals and durations (7.5 nmol mg−1–0.12 μmol mg−1 and 7 h to 2 weeks, respectively). The application of NO-releasing porous materials as coating for subcutaneous implants may improve tissue biocompatibility by mitigating the foreign body response and promoting cell integration. PMID:23915047

Breeding blanket development. Tritium release from breeder

International Nuclear Information System (INIS)

Tsuchiya, Kunihiko; Kawamura, Hiroshi; Nagao, Yoshiharu

2006-01-01

Engineering data on neutron irradiation performance of tritium breeders are needed to design the breeding blanket of fusion reactor. In this study, tritium release experiments of the breeders were carried out to examine the effects of various parameters (such as sweep gas flow rate, hydrogen content in sweep gas, irradiation temperature and thermal neutron flux) on tritium generation and release behavior. Lithium titanate (Li 2 TiO 3 ) is considered as a candidate tritium breeder in the blanket design of International Thermonuclear Experimental Reactor (ITER). As for the shape of the breeder material, a small spherical form is preferred to reduce the thermal stress induced in the breeder. Li 2 TiO 3 pebbles of about 170g in total weight and with 0.3 and 2 mm in diameter were manufactured by a wet process, and an assembly packed with the binary Li 2 TiO 3 pebbles was irradiated in Japan Materials Testing Reactor (JMTR). The tritium was generated in the Li 2 TiO 3 pebble bed and released from the pebble bed, and was swept downstream using the sweep gas for on-line analysis of tritium content. Concentration of total tritium and gaseous tritium (HT or T 2 gas) released from the Li 2 TiO 3 pebble bed were measured by ionization chambers, and the ratio of (gaseous tritium)/(total tritium) was evaluated. The sweep gas flow rate was changed from 100 to 900cm 3 /min, and hydrogen content in the sweep gas was changed from 100 to 10000 ppm. Furthermore, thermal neutron flux was changed using a window made of hafnium (Hf) neutron absorber. The irradiation temperature at an outer region of the Li 2 TiO 3 pebble bed was held between 200 and 400degC. The main results of this experiment are summarized as follows. 1) When the temperature at the outside edge of the Li 2 TiO 3 pebble bed exceeded 100degC, the tritium release from the Li 2 TiO 3 pebble bed started. The ratio of the tritium release rate and the tritium generation rate (normalized tritium release rate: R/G) reached

Optimal advanced credit releases in ecosystem service markets.

Science.gov (United States)

BenDor, Todd K; Guo, Tianshu; Yates, Andrew J

2014-03-01

Ecosystem service markets are popular policy tools for ecosystem protection. Advanced credit releases are an important factor affecting the supply side of ecosystem markets. Under an advanced credit release policy, regulators give ecosystem suppliers a fraction of the total ecosystem credits generated by a restoration project before it is verified that the project actually achieves the required ecological thresholds. In spite of their prominent role in ecosystem markets, there is virtually no regulatory or research literature on the proper design of advanced credit release policies. Using U.S. aquatic ecosystem markets as an example, we develop a principal-agent model of the behavior of regulators and wetland/stream mitigation bankers to determine and explore the optimal degree of advance credit release. The model highlights the tension between regulators' desire to induce market participation, while at the same time ensuring that bankers successfully complete ecological restoration. Our findings suggest several simple guidelines for strengthening advanced credit release policy.

Release of ultrafine particles from three simulated building processes

International Nuclear Information System (INIS)

Kumar, Prashant; Mulheron, Mike; Som, Claudia

2012-01-01

Building activities are recognised to produce coarse particulate matter but less is known about the release of airborne ultrafine particles (UFPs; those below 100 nm in diameter). For the first time, this study has investigated the release of particles in the 5–560 nm range from three simulated building activities: the crushing of concrete cubes, the demolition of old concrete slabs, and the recycling of concrete debris. A fast response differential mobility spectrometer (Cambustion DMS50) was used to measure particle number concentrations (PNC) and size distributions (PNDs) at a sampling frequency of 10 Hz in a confined laboratory room providing controlled environment and near–steady background PNCs. The sampling point was intentionally kept close to the test samples so that the release of new UFPs during these simulated processes can be quantified. Tri–modal particle size distributions were recorded for all cases, demonstrating different peak diameters in fresh nuclei ( 4 cm −3 . These background modal peaks shifted towards the larger sizes during the work periods (i.e. actual experiments) and the total PNCs increased between 2 and 17 times over the background PNCs for different activities. After adjusting for background concentrations, the net release of PNCs during cube crushing, slab demolition, and ‘dry’ and ‘wet’ recycling events were measured as ∼0.77, 19.1, 22.7 and 1.76 (×10 4 ) cm −3 , respectively. The PNDs were converted into particle mass concentrations (PMCs). While majority of new PNC release was below 100 nm (i.e. UFPs), the bulk of new PMC emissions were constituted by the particles over 100 nm; ∼95, 79, 73 and 90% of total PNCs, and ∼71, 92, 93 and 91% of total PMCs, for cube crushing, slab demolition, dry recycling and wet recycling, respectively. The results of this study firmly elucidate the release of UFPs and raise a need for further detailed studies and designing health and safety related exposure guidelines for

Release fraction of PWR after severe accidents. Vol. 4

Energy Technology Data Exchange (ETDEWEB)

Aziz, M; El-Messeiry, A M [National Center for Nuclear Safety and Radiation Control, Atomic Energy Authority, Cairo (Egypt)

1996-03-01

Fission fragments and gases are emitted after accidents as a result of core meltdown and core concrete interactions. These aerosols are transported and fill the reactor containment. With increasing the pressure above pressure design bases, a failure of containment may occur and subsequently these aerosols will release into the external environment leading to a source term of radioactivity that affects the safety of workers and public. The amount of aerosol which escapes to the environment can be described by the release fraction which is defined as the total accumulated aerosol which initially enters the containment. The factors that affect the release fraction is studied, and the aerosol dynamics equation is used to model the release of aerosol to the outside atmosphere. These factors are containment pressure, failure time,break area, the size of aerosol particle. It found that early failure time and higher pressure increase the release fraction, also the release faction is affected by the area and the aerosol particle size. 7 figs., 2 tabs.

Release fraction of PWR after severe accidents. Vol. 4

International Nuclear Information System (INIS)

Aziz, M.; El-Messeiry, A.M.

1996-01-01

Fission fragments and gases are emitted after accidents as a result of core meltdown and core concrete interactions. These aerosols are transported and fill the reactor containment. With increasing the pressure above pressure design bases, a failure of containment may occur and subsequently these aerosols will release into the external environment leading to a source term of radioactivity that affects the safety of workers and public. The amount of aerosol which escapes to the environment can be described by the release fraction which is defined as the total accumulated aerosol which initially enters the containment. The factors that affect the release fraction is studied, and the aerosol dynamics equation is used to model the release of aerosol to the outside atmosphere. These factors are containment pressure, failure time,break area, the size of aerosol particle. It found that early failure time and higher pressure increase the release fraction, also the release faction is affected by the area and the aerosol particle size. 7 figs., 2 tabs

Tuning silver ion release properties in reactively sputtered Ag/TiOx nanocomposites

Science.gov (United States)

Xiong, J.; Ghori, M. Z.; Henkel, B.; Strunskus, T.; Schürmann, U.; Deng, M.; Kienle, L.; Faupel, F.

2017-07-01

Silver/titania nanocomposites with strong bactericidal effects and good biocompatibility/environmental safety show a high potential for antibacterial applications. Tailoring the silver ion release is thus highly promising to optimize the antibacterial properties of such coatings and to preserve biocompatibility. Reactive sputtering is a fast and versatile method for the preparation of such Ag/TiOx nanocomposites coatings. The present work is concerned with the influence of sputter parameters on the surface morphology and silver ion release properties of reactively sputtered Ag/TiOx nanocomposites coatings showing a silver nanoparticle size distribution in the range from 1 to 20 nm. It is shown that the silver ion release rate strongly depends on the total pressure: the coatings prepared at lower pressure present a lower but long-lasting release behavior. The much denser structure produced under these conditions reduces the transport of water molecules into the coating. In addition, the influence of microstructure and thickness of titanium oxide barriers on the silver ion release were investigated intensively. Moreover, for the coatings prepared at high total pressure, it was demonstrated that stable and long-lasting silver release can be achieved by depositing a barrier with a high rate. Nanocomposites produced under these conditions show well controllable silver ion release properties for applications as antibacterial coatings.

Surgical Stabilization of the Medial Capsulo-Ligamentous Envelope in Total Knee Arthroplasty

Directory of Open Access Journals (Sweden)

Brandon Green, DO

2014-10-01

Full Text Available This study will evaluate an alternative method in which a four prong bone staple was used to repair the medial collateral ligament following over-release or avulsion injuries in (#6 cases during a total knee arthroplasty. The use of a four prong bone staple to repair medial collateral ligament injuries status post total knee replacement will provide satisfactory results with respect to post-operative knee stability and range of motion. Our retrospective review revealed that all six patients improved with regards to range of motion following the total knee arthroplasty. We feel that repair of the medial collateral ligament with a four-prong bone staple is a viable option after an over-release or avulsion injury sustained during a total knee arthroplasty.

The influence of "host release factor" on carbon release by zooxanthellae isolated from fed and starved Aiptasia pallida (Verrill).

Science.gov (United States)

Davy, S K; Cook, C B

2001-06-01

Symbiotic dinoflagellates (zooxanthellae) typically respond to extracts of host tissue with enhanced release of short-term photosynthetic products. We examined this "host release factor" (HRF) response using freshly isolated zooxanthellae of differing nutritional status. The nutritional status was manipulated by either feeding or starving the sea anemone Aiptasia pallida (Verrill). The release of fixed carbon from isolated zooxanthellae was measured using 14C in 30 min experiments. Zooxanthellae in filtered seawater alone released approximately 5% of photosynthate irrespective of host feeding history. When we used a 10-kDa ultrafiltrate of A. pallida host tissue as a source of HRF, approximately 14% of photosynthate was released to the medium. This increased to over 25% for zooxanthellae from anemones starved for 29 days or more. The cell-specific photosynthetic rate declined with starvation in these filtrate experiments, but the decline was offset by the increased percentage release. Indeed, the total amount of released photosynthate remained unchanged, or even increased, as zooxanthellae became more nutrient deficient. Similar trends were also observed when zooxanthellae from A. pallida were incubated in a 3-kDa ultrafiltrate of the coral Montastraea annularis, suggesting that HRF in the different filtrates operated in a similar manner. Our results support the suggestion that HRF diverts surplus carbon away from storage compounds to translocated compounds such as glycerol.

Taking inventory on VOC releases from Amoco's Yorktown refinery

International Nuclear Information System (INIS)

Klee, H.H. Jr.; Schmitt, R.E.; Harrass, M.C.; Podar, M.K.

1996-01-01

Amoco's Yorktown, Virginia, refinery is a 35-year-old, 53,000 bbl/day facility that manufacturers gasoline, heating oil, liquid petroleum gas, sulfur, and coke. In a cooperative and voluntary effort, Amoco Corporation and the US Environmental Protection Agency conducted a joint project to study pollution prevention opportunities at an operating industrial facility. Source reduction efforts--key to pollution prevention strategies--require knowledge of specific sources of releases. However, data on releases from individual process units are limited in favor of data to monitor existing end-of-pipe pollution control requirements. The study's sampling program sought to portray the distribution of releases within the refinery, their management within the refinery, and ultimate releases leaving the refinery. Subsequent tests of blowdown stack and fugitive emissions further improved total release estimates. The initial study estimated that the refinery generates about 25,000 metric tons (t)/year of potential pollutants. Of these, about half are released from the refinery as airborne, waterborne, or land-disposed releases. Airborne releases comprise the majority of releases by mass, about 12,000 t/year. Most of the airborne releases are volatile organic compound hydrocarbons. The inventory sampling project and subsequent work identified differences with Toxic Release Inventory (TRI) values and standard emission factors (AP-42). The inventory and other data provided an opportunity to consider options for, and limitations of, specific pollution prevention or source reduction strategies

Atmosphere dependence of fission products release: The Vercors 4 and 5 experiments

Energy Technology Data Exchange (ETDEWEB)

Andre, B.; Ducros, G.; Tourasse, M.; Ferroud-Plattet, M.P. [CEA Centre d`Etudes de Grenoble, 38 (France). Dept. de Thermohydraulique et de Physique; Boulaud, D. [CEA Centre d`Etudes de Fontenay-aux-Roses, 92 (France). Inst. de Protection et de Surete Nucleaire

1996-12-31

Because of the severe consequences, in terms of radiological and biological effects, of a nuclear accident, the international reactor safety authorities initiated, 25 years ago, numerous experimental programs in order to improve the understanding and the prediction of these situations. In France, the Nuclear Protection and Safety Institute (IPSN) in collaboration with Electricite de France (EDF) co-fund the Heva-Vercors program, since 1983. The experiments are conducted in a shielded hot cell of the LAMA facility at Grenoble. The test specimen is a fuel rod section taken from a power reactor operated by EDF and includes three irradiated pellets in their original cladding. The fuel sample is re-irradiated at low power in the Siloe experimental reactor for seven days in order to recreate the short-lived fission products without inducing any in-pile release. Since the experimental sequence is performed less than 40 hours after the end of the reirradiation, direct measurement of radioactive fission products release is possible using gamma spectrometry. The measurements performed during the tests are essentially aimed at characterising the release kinetics and the total release of fission products and structural materials as a function of fuel temperature and oxidising/reducing conditions of the environment. The four last tests (Vercors 3 to Vercors 6), performed at 2600 K, allowed to measure the kinetic of high and low volatile species release, as well as the total released fraction of non volatile species and the transuranic elements. This paper is devoted to the comparison of the Vercors 4 and Vercors 5 tests. The first one has been conducted up to 2600 K under reducing conditions (hydrogen fluid), after an oxidising period at 1670 K. The second one was performed in a pure steam atmosphere after several plateaus at intermediate temperatures in oxidising conditions. The total release of volatile (Sb, Te, I, Cs) is not significantly modified and a higher release of Mo

The influence of cyclic loading on gentamicin release from acrylic bone cements

NARCIS (Netherlands)

Hendriks, JGE; Neut, D; Hazenberg, JG; Verkerke, GJ; van Horn, [No Value; van der Mei, HC; Busscher, HJ

Antibiotic-loaded acrylic bone cement is widely used in total joint replacement to reduce infections. Walking results in cyclic loading, which has been suggested to stimulate antibiotic release. The goal of this study is to compare antibiotic release from cyclically loaded bone cement with the

Energy released in fission

International Nuclear Information System (INIS)

James, M.F.

1969-05-01

The effective energy released in and following the fission of U-235, Pu-239 and Pu-241 by thermal neutrons, and of U-238 by fission spectrum neutrons, is discussed. The recommended values are: U-235 ... 192.9 ± 0.5 MeV/fission; U-238 ... 193.9 ± 0.8 MeV/fission; Pu-239 ... 198.5 ± 0.8 MeV/fission; Pu-241 ... 200.3 ± 0.8 MeV/fission. These values include all contributions except from antineutrinos and very long-lived fission products. The detailed contributions are discussed, and inconsistencies in the experimental data are pointed out. In Appendix A, the contribution to the total useful energy release in a reactor from reactions other than fission are discussed briefly, and in Appendix B there is a discussion of the variations in effective energy from fission with incident neutron energy. (author)

Single- and multiple-dose pharmacokinetics of biphasic immediate-release/extended-release hydrocodone bitartrate/acetaminophen (MNK-155 compared with immediate-release hydrocodone bitartrate/ibuprofen and immediate-release tramadol HCl/acetaminophen

Directory of Open Access Journals (Sweden)

Devarakonda K

2015-09-01

Full Text Available Krishna Devarakonda,1 Kenneth Kostenbader,2 Michael J Giuliani,3 Jim L Young41Department of Clinical Pharmacology, Mallinckrodt Pharmaceuticals, 2Mallinckrodt Pharmaceuticals, 3Research and Development, Mallinckrodt Pharmaceuticals, 4Department of Clinical Affairs and Program Management, Mallinckrodt Pharmaceuticals, Hazelwood, MO, USAObjective: To characterize the single-dose and steady-state pharmacokinetics (PK of biphasic immediate-release/extended-release hydrocodone bitartrate/acetaminophen (IR/ER HB/APAP, IR HB/ibuprofen, and IR tramadol HCl/APAP.Methods: In this single-center, open-label, randomized, four-period crossover study, healthy participants received four treatments under fasted conditions: 1 a single dose of two IR/ER HB/APAP 7.5/325 mg tablets (15/650 mg total dose on day 1, followed by two tablets every 12 hours (q12h beginning on day 3; 2 a single dose of IR HB/ibuprofen 15/400 mg (divided as one 7.5/200 mg tablet at hour 0 and 6, followed by one tablet every 6 hours (q6h beginning on day 3; 3 a single dose of IR tramadol HCl/APAP 75/650 mg (divided as one 37.5/325 mg tablet at hour 0 and 6, followed by one tablet q6h beginning on day 3; and 4 a single dose of three IR/ER HB/APAP 7.5/325 mg tablets (22.5/975 mg total dose on day 1, a three-tablet initial dose at 48 hours followed by two-tablet doses q12h beginning on day 3. Hydrocodone and APAP single-dose and steady-state PK were assessed. Adverse events were monitored.Results: The PK analysis was carried out on 29 of 48 enrolled participants who completed all treatment periods. Single-dose hydrocodone exposure was similar for IR/ER HB/APAP 22.5/975 mg and IR HB/ibuprofen 15/400 mg; time to maximum observed plasma concentration was shorter and half-life was longer for IR/ER HB/APAP (22.5/975 mg and 15/650 mg vs IR HB/ibuprofen. Single-dose APAP exposure was similar for IR/ER HB/APAP 15/650 mg and IR tramadol HCl/APAP 75/650 mg. Steady-state hydrocodone and APAP exposures

Unrestricted release measurements with ambient air ionization monitors

International Nuclear Information System (INIS)

MacArthur, D.; Gunn, R.; Dockray, T.; Luff, C.

1999-01-01

Radiation monitoring systems based on the long-range alpha detection (LRAD) technique, such as the BNFL Instruments IonSens trademark, provide a single contamination measurement for an entire object rather than the more familiar individual readings for smaller surface areas. The LRAD technique relies on the ionization of ambient air molecules by alpha particles, and the subsequent detection of these ions, rather than direct detection of the alpha particles themselves. A single monitor can detect all of the ions produced over a large object and report a total contamination level for the entire surface of that object. However, both the unrestricted release limits specified in USDOE Order 5400.5 (and similar documents in other countries), and the definitions of radioactive waste categories, are stated in terms of contamination per area. Thus, conversion is required between the total effective contamination as measured by the LRAD-based detector and the allowable release limits. In addition, since the release limits were not written assuming an averaging detector system, the method chosen to average the assumed contamination over the object can have a significant impact on the effective sensitivity of the detector

Total. Group dynamics and activities. Competitive environment and strategic perspectives. Release - July 2017

International Nuclear Information System (INIS)

2017-07-01

After a synthesis which notably proposes a SWOT analysis of the Total group, this report proposes a presentation of the Total Group (general overview, presentation of activities, human resources, shareholder structure and stock market data, competitive environment). It gives an overview of the Total group dynamics and of its activities through a presentation of an environment analysis (world oil demand, refining-chemistry activity, hydrocarbon prices), a presentation of the group activity (turnover, turnover per segment, operational income and financial results of competitors). It comments important events and development axes: four strategic orientations, strengthening of the upstream pole, restructuring of refining and chemical activities, widening of the energy provision, consolidation of positions in the marketing and services sector. Financial data are presented along with the main economic and financial indicators. Important statistical data are provided

Releases of radioactivity at the Savannah River Plant, 1954-1980

Energy Technology Data Exchange (ETDEWEB)

Ashley, C.; Zeigler, C. C.; Culp, P. A.

1982-01-01

This report contains summaries of releases of radioactivity to onsite seepage basins and to plant effluents for each year since plant startup (1954 through 1980). Releases for the years 1954 through 1959 were reassessed in 1974 and assigned release values for specific long-lived radionuclides. These long-lived radionuclides (half-lives greater than 1 year) are the only radionuclides included for the years 1954 through 1970. Since 1970 all detectable radionuclides have been included. Measured migration o radionuclides from F-, H-, and K-Area seepage basins and desorption of /sup 137/Cs from the Four Mile Creek stream bed are included in Summary B of this report. Summaries of monthly releases for 1979 and 1980 and total SRP releases by radionuclide in three categories: liquid to seepage basins, liquid to streams, and atmospheric are also included. Monthly releases for 1979 are included because the 1979 issue of this report was not published. All 1979 data are included in this report.

Total-System Analyzer for performance assessment of Yucca Mountain

International Nuclear Information System (INIS)

Wilson, M.L.; Lauffer, F.C.; Cummings, J.C.; Zieman, N.B.

1990-01-01

The Total-System Analyzer is a modular computer program for probabilistic total-system performance calculations. The code employs stratified random sampling from model parameter distribution functions to generate multiple realizations of the system. The results of flow and transport calculations for each realization are combined into a probability distribution function of the system response as indicated by the performance measure. We give a detailed description of the code and present results for four example problems simulating the release of radionuclides from a proposed high-level-waste repository at Yucca Mountain, Nevada. The example simulations illustrate the impact of significant variation of percolation flux and sorption on radionuclide releases. We discuss the effects of numerical sampling error and of correlations among the model parameters. 20 refs., 7 figs., 2 tabs

Estradiol potentiation of gonadotropin-releasing hormone responsiveness in the anterior pituitary is mediated by an increase in gonadotropin-releasing hormone receptors

International Nuclear Information System (INIS)

Menon, M.; Peegel, H.; Katta, V.

1985-01-01

In order to investigate the mechanism by which 17 beta-estradiol potentiates the action of gonadotropin-releasing hormone on the anterior pituitary in vitro, cultured pituitary cells from immature female rats were used as the model system. Cultures exposed to estradiol at concentrations ranging from 10(-10) to 10(-6) mol/L exhibited a significant augmentation of luteinizing hormone release in response to a 4-hour gonadotropin-releasing hormone (10 mumol/L) challenge at a dose of 10(-9) mol/L compared to that of control cultures. The estradiol augmentation of luteinizing hormone release was also dependent on the duration of estradiol exposure. When these cultures were incubated with tritium-labeled L-leucine, an increase in incorporation of radiolabeled amino acid into total proteins greater than that in controls was observed. A parallel stimulatory effect of estradiol on iodine 125-labeled D-Ala6 gonadotropin-releasing hormone binding was observed. Cultures incubated with estradiol at different concentrations and various lengths of time showed a significant increase in gonadotropin-releasing hormone binding capacity and this increase was abrogated by cycloheximide. Analysis of the binding data showed that the increase in gonadotropin-releasing hormone binding activity was due to a change in the number of gonadotropin-releasing hormone binding sites rather than a change in the affinity. These results suggest that (1) estradiol treatment increases the number of pituitary receptors for gonadotropin-releasing hormone, (2) the augmentary effect of estradiol on luteinizing hormone release at the pituitary level might be mediated, at least in part, by the increase in the number of binding sites of gonadotropin-releasing hormone, and (3) new protein synthesis may be involved in estradiol-mediated gonadotropin-releasing hormone receptor induction

Historical releases of mercury to air, land, and water from coal combustion.

Science.gov (United States)

Streets, David G; Lu, Zifeng; Levin, Leonard; Ter Schure, Arnout F H; Sunderland, Elsie M

2018-02-15

Coal combustion is one of the largest contemporary sources of anthropogenic mercury (Hg). It releases geologically sequestered Hg to the atmosphere, and fly ash can contaminate terrestrial and aquatic systems. We estimate that coal combustion has released a cumulative total of 38.0 (14.8-98.9, 80% C.I.) Gg (gigagrams, 10 9 g or thousand tonnes) of Hg to air, land, and water up to the year 2010, most of which (97%) has occurred since 1850. The rate of release has grown by two orders of magnitude from 0.01Ggyr -1 in 1850 to 1Ggyr -1 in 2010. Geographically, Asia and Europe each account for 32% of cumulative releases and an additional 18% is from North America. About 26.3 (10.2-68.3) Gg, 71% of the total, were directly emitted to the atmosphere, mostly from the industrial (45%) and power generation (36%) sectors, while the remainder was disposed of to land and water bodies. While Europe and North America were the major contributing regions until 1950, Asia has surpassed both in recent decades. By 2010, Asia was responsible for 69% of the total releases of Hg from coal combustion to the environment. Control technologies installed on major emitting sources capture mainly particulate and divalent Hg, and therefore the fraction of elemental Hg in emissions from coal combustion has increased over time from 0.46 in 1850 to 0.61 in 2010. About 11.8 (4.6-30.6) Gg of Hg, 31% of the total, have been transferred to land and water bodies through the disposal or utilization of Hg-containing combustion waste and collected fly ash/FGD waste; approximately 8.8Gg of this Hg have simply been discarded to waste piles or ash ponds or rivers. Copyright © 2017 Elsevier B.V. All rights reserved.

Potential for control of Cadra cautella (Walker) by release of fully or partially sterile males

International Nuclear Information System (INIS)

Brower, J.H.; Tilton, E.W.

1975-01-01

Modifications of the sterile-male release technique appear to offer promise for the control of post-harvest lepidopteran pest populations within storage structures. Theoretical models of release strategies for Cadra cautella showed that each method has an 'ideal' flooding ratio. This ratio represents the best balance between extinction in a few generations and minimization of the total number of insects released. From data reported concerning the population dynamics of Cadra cautella in the field an ideal flooding ratio for fully sterile (S) males to fertile (F) males of 97:1 would achieve extinction in 3 generations. Total numbers of males released per 100 native insects that would be needed to achieve extinction at these flooding ratios would be 14,850, 14,900 and 18,500, respectively. (author)

Estimation of cobalt release from feed water heater tubes of BWRs

International Nuclear Information System (INIS)

Uchida, S.; Kitamura, M.; Ozawa, Y.

1983-01-01

To evaluate the release source of cobalt from heater tubes of the feed water line, release rate measurements were carried out by detecting 60 Co released from irradiated stainless steel in contact with neutral water at an oxygen concentration of 20 ppb. The dependences of cobalt release rate on temperature, flow velocity and exposure time were studied after 670 hours of release experiments, and an empirical equation (which is presented) was obtained in the temperature range from 150 to 240 deg C. A decrease in the cobalt release rate above 250 deg C was considered due to the formation of a protective oxide layer. From these data, the amount of cobalt released from individual feed water heaters was evaluated. It was demonstrated that low cobalt containing stainless steel was economically applied only in the higher temperature region of the heater (20% of the total surface) to reduce cobalt feed rate into the reactor (to approx. 1/2). (author)

Barrier and operational risk analysis of hydrocarbon releases (BORA-Release)

International Nuclear Information System (INIS)

Sklet, Snorre; Vinnem, Jan Erik; Aven, Terje

2006-01-01

This paper presents results from a case study carried out on an offshore oil and gas production platform with the purpose to apply and test BORA-Release, a method for barrier and operational risk analysis of hydrocarbon releases. A description of the BORA-Release method is given in Part I of the paper. BORA-Release is applied to express the platform specific hydrocarbon release frequencies for three release scenarios for selected systems and activities on the platform. The case study demonstrated that the BORA-Release method is a useful tool for analysing the effect on the release frequency of safety barriers introduced to prevent hydrocarbon releases, and to study the effect on the barrier performance of platform specific conditions of technical, human, operational, and organisational risk influencing factors (RIFs). BORA-Release may also be used to analyse the effect on the release frequency of risk reducing measures

Modulation of precipitation by conditional symmetric instability release

Science.gov (United States)

Glinton, Michael R.; Gray, Suzanne L.; Chagnon, Jeffrey M.; Morcrette, Cyril J.

2017-03-01

Although many theoretical and observational studies have investigated the mechanism of conditional symmetric instability (CSI) release and associated it with mesoscale atmospheric phenomena such as frontal precipitation bands, cloud heads in rapidly developing extratropical cyclones and sting jets, its climatology and contribution to precipitation have not been extensively documented. The aim of this paper is to quantify the contribution of CSI release, yielding slantwise convection, to climatological precipitation accumulations for the North Atlantic and western Europe. Case studies reveal that CSI release could be common along cold fronts of mature extratropical cyclones and the North Atlantic storm track is found to be a region with large CSI according to two independent CSI metrics. Correlations of CSI with accumulated precipitation are also large in this region and CSI release is inferred to be occurring about 20% of the total time over depths of over 1 km. We conclude that the inability of current global weather forecast and climate prediction models to represent CSI release (due to insufficient resolution yet lack of subgrid parametrization schemes) may lead to errors in precipitation distributions, particularly in the region of the North Atlantic storm track.

Underground Nuclear Explosions and Release of Radioactive Noble Gases

Science.gov (United States)

Dubasov, Yuri V.

2010-05-01

Over a period in 1961-1990 496 underground nuclear tests and explosions of different purpose and in different rocks were conducted in the Soviet Union at Semipalatinsk and anovaya Zemlya Test Sites. A total of 340 underground nuclear tests were conducted at the Semipalatinsk Test Site. One hundred seventy-nine explosions (52.6%) among them were classified as these of complete containment, 145 explosions (42.6%) as explosions with weak release of radioactive noble gases (RNG), 12 explosions (3.5%) as explosions with nonstandard radiation situation, and four excavation explosions with ground ejection (1.1%). Thirty-nine nuclear tests had been conducted at the Novaya Zemlya Test Site; six of them - in shafts. In 14 tests (36%) there were no RNG release. Twenty-three tests have been accompanied by RNG release into the atmosphere without sedimental contamination. Nonstandard radiation situation occurred in two tests. In incomplete containment explosions both early-time RNG release (up to ~1 h) and late-time release from 1 to 28 h after the explosion were observed. Sometimes gas release took place for several days, and it occurred either through tunnel portal or epicentral zone, depending on atmospheric air temperature.

Tritium and helium release from beryllium pebbles neutron-irradiated up to 230appm tritium and 3000appm helium

Directory of Open Access Journals (Sweden)

Vladimir Chakin

2016-12-01

Full Text Available Study of tritium and helium release from beryllium pebbles with diameters of 0.5 and 1mm after high-dose neutron irradiation at temperatures of 686–968K was performed. The release rate always has a single peak, and the peak temperatures at heating rates of 0.017K/s and 0.117K/s lie in the range of 1100–1350K for both tritium and helium release. The total tritium release from 1mm pebbles decreases considerably by increasing the irradiation temperature. The total tritium release from 0.5mm pebbles is less than that from 1mm pebbles and remains constant regardless of the irradiation temperature. At high irradiation temperatures, open channels are formed which contribute to the enhanced tritium release.

Minthorn Springs Creek summer juvenile release and adult collection facility: Annual report 1992; ANNUAL

International Nuclear Information System (INIS)

Rowan, Gerald D.

1993-01-01

The Confederated Tribes of the Umatilla Indian Reservation (CT'UIR) and Oregon Department of Fish and Wildlife (ODFW) are cooperating in a joint effort to supplement steelhead and re-establish salmon runs in the Umatilla River Basin. As an integral part of this program, Bonifer and Minthorn Acclimation Facilities are operated for holding and spawning adult steelhead and fall chinook salmon and acclimation and release of juvenile salmon and steelhead. Acclimation of 109,101 spring chinook salmon and 19,977 summer steelhead was completed at Bonifer in the spring of 1992. At Minthorn, 47,458 summer steelhead were acclimated and released. Control groups of spring chinook salmon were released instream concurrent with the acclimated releases to evaluate the effects of acclimation on adult returns to the Umatilla River. Acclimation studies with summer steelhead were not conducted in 1992. A total of 237 unmarked adult steelhead were collected for broodstock at Three Mile Dam from October 18, 1991 through April 24, 1992 and held at Minthorn. Utilizing a 3 x 3 spawning matrix, a total of 476,871 green eggs were taken from 86 females. The eggs were transferred to Umatilla Hatchery for incubation, rearing, and later release into the Umatilla River. A total of 211 fall chinook salmon were also collected for broodstock at Three Mile Dam and held at Minthorn. Using a 1:1 spawning ratio, a total of 195,637 green eggs were taken from 58 females. They were also transferred to Umatilla Hatchery for incubation, rearing, and later release into the Umatilla River. Personnel from the ODFW Eastern Oregon Fish Pathology Laboratory in La Grande took samples of tissues and reproductive fluids from Umatilla River summer steelhead and fall chinook salmon broodstock for monitoring and evaluation purposes. Cell culture assays for replicating agents, including IHNV virus, on all spawned fish were negative. One of 60 summer steelhead tested positive for EIBS virus, while all fall chinook tested

Chromium(III) and chromium(VI) release from leather during 8 months of simulated use.

Science.gov (United States)

Hedberg, Yolanda S; Lidén, Carola

2016-08-01

Chromium (Cr) release from Cr-tanned leather articles is a major cause of Cr contact dermatitis. It has been suggested that Cr(VI) release from leather is not necessarily an intrinsic property of the leather, but is strongly dependent on environmental conditions. To test this hypothesis for long-term (8 months) simulated use. The release of total Cr and Cr(VI) from Cr-tanned, unfinished leather was analysed in subsequent phosphate buffer (pH 8.0) immersions for a period of 7.5 months. The effect of combined ultraviolet treatment and alkaline solution (pH 12.1) was tested. Dry storage [20% relative humidity (RH)] was maintained between immersions. Atomic absorption spectroscopy, X-ray fluorescence and diphenylcarbazide tests were used. Cr(VI) release was dependent on previous dry storage or alkaline treatment, but not on duration or number of previous immersions. Cr(III) release decreased with time. Fifty-two percent of the total Cr released during the last immersion period was Cr(VI). Cr(VI) release exceeded 9 mg/kg in all immersion periods except in the first 10-day immersion (2.6 mg/kg). Cr(VI) release is primarily determined by environmental factors (RH prior to immersion, solution pH, and antioxidant content). The RH should be kept low prior to testing Cr(VI) release from leather. © 2016 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.

Interactions of MK-801 with glutamate-, glutamine- and methamphetamine-evoked release of [3H]dopamine from striatal slices

International Nuclear Information System (INIS)

Bowyer, J.F.; Scallet, A.C.; Holson, R.R.; Lipe, G.W.; Slikker, W. Jr.; Ali, S.F.

1991-01-01

The interactions of MK-801 [(+)-5-methyl-10,11-dihydro-5H-dibenzo[a,d] cyclohepten-5,10-imine], glutamate and glutamine with methamphetamine (METH)-evoked release of [ 3 H]dopamine were assessed in vitro to determine whether MK-801 inhibition of METH neurotoxicity might be mediated presynaptically, and to evaluate the effects of glutamatergic stimulation on METH-evoked dopamine release. MK-801 inhibition of glutamate- or METH-evoked dopamine release might reduce synaptic dopamine levels during METH exposure and decrease the formation of 6-hydroxydopamine or other related neurotoxins. Without Mg 2+ present, 40 microM and 1 mM glutamate evoked a N-methyl-D-aspartate receptor-mediated [ 3 H]dopamine and [ 3 H]metabolite (tritium) release of 3 to 6 and 12 to 16% of total tritium stores, respectively, from striatal slices. With 1.50 mM Mg 2+ present, 10 mM glutamate alone or in combination with the dopamine uptake blocker nomifensine released only 2.1 or 4.2%, respectively, of total tritium stores, and release was only partially dependent on N-methyl-D-aspartate-type glutamate receptors. With or without 1.50 mM Mg 2+ present, 0.5 or 5 microM METH evoked a substantial release of tritium (5-8 or 12-21% of total stores, respectively). METH-evoked dopamine release was not affected by 5 microM MK-801 but METH-evoked release was additive with glutamate-evoked release. Without Mg 2+ present, 1 mM glutamine increased glutamate release and induced the release of [ 3 H]dopamine and metabolites. Both 0.5 and 5 microM METH also increased tritium release with 1 mM glutamine present. When striatal slices were exposed to 5 microM METH this glutamine-evoked release of glutamate was increased more than 50%

2001 Toxic Chemical Release Inventory Emergency Planning and Community Right to Know Act SEC 313

International Nuclear Information System (INIS)

ZALOUDEK, D.E.

2002-01-01

Pursuant to section 313 of the Emergency Planning and Community Right-To-Know Act of 1986 (EPCRA), and Executive Order 13148, Greening the Government Through Leadership in Environmental Management, the US Department of Energy has prepared and submitted a Toxic Chemical Release Inventory for the Hanford Site covering activities performed during calendar year 2001. EPCRA Section 313 requires facilities that manufacture, process, or otherwise use listed toxic chemicals in quantities exceeding established threshold levels to report total annual releases of those chemicals. During calendar year 2001, Hanford Site activities resulted in one chemical used in amounts exceeding an activity threshold. Accordingly, the Hanford Site 2001 Toxic Chemical Release Inventory, DOE/RL-2002-37, includes total annual amount of lead released to the environment, transferred to offsite locations, and otherwise managed as waste

Selective release of phosphorus and nitrogen from waste activated sludge with combined thermal and alkali treatment.

Science.gov (United States)

Kim, Minwook; Han, Dong-Woo; Kim, Dong-Jin

2015-08-01

Selective release characteristics of phosphorus and nitrogen from waste activated sludge (WAS) were investigated during combined thermal and alkali treatment. Alkali (0.001-1.0N NaOH) treatment and combined thermal-alkali treatment were applied to WAS for releasing total P(T-P) and total nitrogen(T-N). Combined thermal-alkali treatment released 94%, 76%, and 49% of T-P, T-N, and COD, respectively. Release rate was positively associated with NaOH concentration, while temperature gave insignificant effect. The ratio of T-N and COD to T-P that released with alkali treatment ranged 0.74-0.80 and 0.39-0.50, respectively, while combined thermal-alkali treatment gave 0.60-0.90 and 0.20-0.60, respectively. Selective release of T-P and T-N was negatively associated with NaOH. High NaOH concentration created cavities on the surface of WAS, and these cavities accelerated the release rate, but reduced selectivity. Selective release of P and N from sludge has a beneficial effect on nutrient recovery with crystallization processes and it can also enhance methane production. Copyright © 2015 Elsevier Ltd. All rights reserved.

Influence of environmental factors on mercury release in hydroelectric reservoirs

Energy Technology Data Exchange (ETDEWEB)

Morrison, K.; Therien, N.

1991-04-01

Due to increased mercury concentrations in fish in hydro-electric reservoirs after flooding, a study was carried out to evaluate the release and transformation of mercury due to vegetation and soil flooded as a result of reservoir creation. Samples of vegetation and soils were immersed in water and concentrations of total mercury, methylmercury and nutrients were followed. The effects of anoxia, pH and temperature on release and transformation were examined. An existing dynamic model of decomposition of flooded materials in reservoirs was modified to include mercury release and transformation, and was calibrated to the experimental data. Amounts of mercury released by the different substrates was of the same order of magnitude. Tree species contributed to the greatest amounts of methylmercury per unit biomass, but the biomass used for these was twigs and foliage. Soil released significant amounts of mercury, but methylation was very low. The model was able to fit well for all substrates except lichen. The model can be adapted to proposed reservoirs to predict nutrient and mecury release and transformation. 175 refs., 38 figs., 38 tabs.

Release of radionuclides following severe accident in interim storage facility. Source term determination

International Nuclear Information System (INIS)

Morandi, S.; Mariani, M.; Giacobbo, F.; Covini, R.

2006-01-01

Among the severe accidents that can cause the release of radionuclides from an interim storage facility, with a consequent relevant radiological impact on the population, there is the impact of an aircraft on the facility. In this work, a safety assessment analysis for the case of an aircraft crash into an interim storage facility is tackled. To this aim a methodology, based upon DOE, IAEA and NUREG standard procedures and upon conservative yet realistic hypothesis, has been developed in order to evaluate the total radioactivity, source term, released to the biosphere in consequence of the impact, without recurring to the use of complicated numerical codes. The procedure consists in the identification of the accidental scenarios, in the evaluation of the consequent damage to the building structures and to the waste packages and in the determination of the total release of radionuclides through the building-atmosphere interface. The methodology here developed has been applied to the case of an aircraft crash into an interim storage facility currently under design. Results show that in case of perforation followed by a fire incident the total released activity would be greater of some orders of magnitude with respect to the case of mere perforation. (author)

Synaptic vesicle exocytosis in hippocampal synaptosomes correlates directly with total mitochondrial volume

Science.gov (United States)

Ivannikov, Maxim V.; Sugimori, Mutsuyuki; Llinás, Rodolfo R.

2012-01-01

Synaptic plasticity in many regions of the central nervous system leads to the continuous adjustment of synaptic strength, which is essential for learning and memory. In this study, we show by visualizing synaptic vesicle release in mouse hippocampal synaptosomes that presynaptic mitochondria and specifically, their capacities for ATP production are essential determinants of synaptic vesicle exocytosis and its magnitude. Total internal reflection microscopy of FM1-43 loaded hippocampal synaptosomes showed that inhibition of mitochondrial oxidative phosphorylation reduces evoked synaptic release. This reduction was accompanied by a substantial drop in synaptosomal ATP levels. However, cytosolic calcium influx was not affected. Structural characterization of stimulated hippocampal synaptosomes revealed that higher total presynaptic mitochondrial volumes were consistently associated with higher levels of exocytosis. Thus, synaptic vesicle release is linked to the presynaptic ability to regenerate ATP, which itself is a utility of mitochondrial density and activity. PMID:22772899

Tritium release experiments with CATS and numerical simulation

International Nuclear Information System (INIS)

Munakata, Kenzo; Wajima, Takaaki; Hara, Keisuke; Wada, Kohei; Takeishi, Toshiharu; Shinozaki, Yohei; Mochizuki, Kazuhiro; Katekari, Kenichi; Kobayashi, Kazuhiro; Iwai, Yasunori; Hayashi, Takumi; Yamanishi, Toshihiko

2010-01-01

In D-T fusion power plants, large amounts of tritium would be handled. Tritium is the radioisotope of protium, and is easily taken into the human body, and thus the behavior of tritium accidentally released in fusion power plants should be studied for the safety design and radioprotection of workers. Therefore, it is necessary to investigate the behavior of tritium released into large rooms with objectives, since complex flow fields should exist in such rooms and they could influence the ventilation of the air containing released tritium. Thus, tritium release experiments were conducted using Caisson Assembly for Tritium Safety Study (CATS) in TPL/JAEA. Some data were taken for tritium behavior in the ventilated area and response of tritium monitors. In the experiments, approximately 17 GBq of tritium was released into Caisson with the total volume of 12 m 3 , and the room was ventilated at the rate of 12 m 3 /h after release of tritium. It was found that placement of an objective in the vessel substantially affects decontamination efficiency. With regard to an experimental result, numerical calculation was performed and the experimental result and the result of numerical calculation were compared, which indicates that experimental results are qualitatively reproduced by numerical calculation. However, further R and D needs to be carried out for quantitative reproduction of the experimental results.

Tritium release experiments with CATS and numerical simulation

Energy Technology Data Exchange (ETDEWEB)

Munakata, Kenzo, E-mail: kenzo@gipc.akita-u.ac.jp [Faculty of Engineering and Resource Sciences, Akita University, Tegata-gakuen-cho 1-1, Akita 010-8502 (Japan); Wajima, Takaaki; Hara, Keisuke; Wada, Kohei [Faculty of Engineering and Resource Sciences, Akita University, Tegata-gakuen-cho 1-1, Akita 010-8502 (Japan); Takeishi, Toshiharu; Shinozaki, Yohei; Mochizuki, Kazuhiro; Katekari, Kenichi [Interdisciplinary Graduate School of Engineering Science, Kyushu University, Hakozaki 6-10-1, Higashi-ku, Fukuoka 812-8581 (Japan); Kobayashi, Kazuhiro; Iwai, Yasunori; Hayashi, Takumi; Yamanishi, Toshihiko [Tritium Technology Group, Japan Atomic Energy Agency, Tokai, Ibaraki 319-1195 (Japan)

2010-12-15

In D-T fusion power plants, large amounts of tritium would be handled. Tritium is the radioisotope of protium, and is easily taken into the human body, and thus the behavior of tritium accidentally released in fusion power plants should be studied for the safety design and radioprotection of workers. Therefore, it is necessary to investigate the behavior of tritium released into large rooms with objectives, since complex flow fields should exist in such rooms and they could influence the ventilation of the air containing released tritium. Thus, tritium release experiments were conducted using Caisson Assembly for Tritium Safety Study (CATS) in TPL/JAEA. Some data were taken for tritium behavior in the ventilated area and response of tritium monitors. In the experiments, approximately 17 GBq of tritium was released into Caisson with the total volume of 12 m{sup 3}, and the room was ventilated at the rate of 12 m{sup 3}/h after release of tritium. It was found that placement of an objective in the vessel substantially affects decontamination efficiency. With regard to an experimental result, numerical calculation was performed and the experimental result and the result of numerical calculation were compared, which indicates that experimental results are qualitatively reproduced by numerical calculation. However, further R and D needs to be carried out for quantitative reproduction of the experimental results.

Dry washing: the solution for contaminated liquid effluent releases

International Nuclear Information System (INIS)

L'homme, D.; Trambouze, P.

1998-01-01

The release of wash water used for contaminated garments poses an ever-increasing problem on nuclear sites. Even though the radioactivity is low, it mixes with organic compounds, thus polluting a large quantity of liquid effluents. In many cases, several thousands of m 3 /year per nuclear site are produced, which at times represents more than 30% of the volume of total releases. The conventional dry cleaning process is not a viable option, given that repeated washing cause clothes to fade and the odors are rot removed completely. In order to eliminate releases, STMI has developed, after several years of research with the Technological University of Compiegne, France, a solvent dry washing process for garments used in the nuclear industry. (author)

Safety aspects of targets for ADTT: Activity, volatile products, residual heat release

International Nuclear Information System (INIS)

Gai, E.V.; Ignatyuk, A.V.; Lunev, V.P.; Shubin, Yu.N.

1999-01-01

Safety aspects of heavy metal liquid targets for the accelerator driven systems connected with the activity accumulation and residual energy release due to the irradiation with high energy proton beam are discussed. The results obtained for the lead-bismuth target that are under construction in IPPE now in the frame of ISTC Project No. 559 are briefly presented. The calculations and the analysis of the accumulation of the spallation reaction products, activity and energy release at various moments after the accelerator shutdown are presented. The concentrations of the reaction products, the total and partial activities, the activities of volatile products are determined. The contributions of the short-lived nuclides important for the prediction of the facility behaviour in regimes with the accelerator beam trips. The calculations and analysis of the residual energy release due to different decay type have been performed. The conclusions are as follows. The obtained results showed that long lived radioactivity accumulates mainly due to primary nuclear reactions. Secondary reactions are responsible for the production of small number of long-lived isotopes Bi-207, Po-210 and some others, being generated by radiative capture of low energy neutrons. It is possible to make a conclusion that neutrons in the energy range 20 - 800 MeV and protons with energy above 100 MeV give main contribution to the total activity generation although these parts of spectra inside the target give comparatively small contribution to the total flux. The correct consideration of short-lived nuclides contribution is the main problem in the analysis of the target behaviour in the case of short accelerator shutdowns. They make the determining contribution to the both activity and the heat release at the first moments after the accelerator shutdown, creating the intermediate links and additional channels for the long-lived nuclides accumulation chains. The strong dependence of calculated

Determination of the sterile release rate for stopping growing age-structured populations

International Nuclear Information System (INIS)

Barclay, Hugh John

2016-01-01

A freely-growing age-structured population was modelled for growth and control by sterile male releases. Equilibrium populations yield critical sterile male release rates that would hold the population at equilibrium. It is shown here that these rates may be different from the release rates required to stop a growing population and bring it to an equilibrium. A computer simulation was constructed of this population and a parameter sensitivity analysis graphed the effects on the required sterile male release rate of fertility, mating delay in adult females, net juvenile survivorship, three adult survivorship curves, the time spent in the juvenile stages, and total life span. The adult survivorship curves had the greatest effect on the required sterile release rate for population elimination. The required release rate was also determined for Ceratitis capitata (Wiedemann) using survivorship and fertility data from a laboratory strain. The concepts of over-flooding ratio and release ratio were discussed and quantified for the cases above. (author)

Model to estimate radiation dose commitments to the world population from the atmospheric release of radionuclides (LWBR development program)

International Nuclear Information System (INIS)

Rider, J.L.; Beal, S.K.

1978-02-01

The equations developed for use in the LWBR environmental statement to estimate the dose commitment over a given time interval to a given organ of the population in the entire region affected by the atmospheric releases of a radionuclide are presented and may be used for any assessment of dose commitments in these regions. These equations define the dose commitments to the world resulting from a released radionuclide and each of its daughters and the sum of these dose commitments provides the total dose commitment accrued from the release of a given radionuclide. If more than one radionuclide is released from a facility, then the sum of the dose commitments from each released nuclide and from each daughter of each released nuclide is the total dose commitment to the world from that facility. Furthermore, if more than one facility is considered as part of an industry, then the sum of the dose commitments from the individual facilities represents the total world dose commitment associated with that industry. The actual solutions to these equations are carried out by the AIRWAY computer program. The writing of this computer program entailed defining in detail the specific representations of the various parameters such as scavenging coefficients, resuspension factors, deposition velocities, dose commitment conversion factors, and food uptake factors, in addition to providing specific numerical values for these types of parameters. The program permits the examination of more than one released nuclide at a time and performs the necessary summing to obtain the total dose commitment to the world accrued from the specified releases

Waste isolation pilot plant performance assessment: Radionuclide release sensitivity to diminished brine and gas flows to/from transuranic waste disposal areas

Energy Technology Data Exchange (ETDEWEB)

Day, Brad A.; Camphouse, R. C.; Zeitler, Todd R. [Sandia National Laboratories, Carlsbad (United States)

2017-03-15

Waste Isolation Pilot Plant repository releases are evaluated through the application of modified parameters to simulate accelerated creep closure, include capillary pressure effects on relative permeability, and increase brine and gas saturation in the operations and experimental (OPS/EXP) areas. The modifications to the repository model result in increased pressures and decreased brine saturations in waste areas and increased pressures and brine saturations in the OPS/EXP areas. Brine flows up the borehole during a hypothetical drilling intrusion are nearly identical and brine flows up the shaft are decreased. The modified parameters essentially halt the flow of gas from the southern waste areas to the northern nonwaste areas, except as transported through the marker beds and anhydrite layers. The combination of slightly increased waste region pressures and very slightly decreased brine saturations result in a modest increase in spallings and no significant effect on direct brine releases, with total releases from the Culebra and cutting and caving releases unaffected. Overall, the effects on total high-probability mean releases from the repository are insignificant, with total low-probability mean releases minimally increased. It is concluded that the modified OPS/EXP area parameters have an insignificant effect on the prediction of total releases.

Pore geometry of ceramic device: The key factor of drug release kinetics

Directory of Open Access Journals (Sweden)

Čolović B.

2013-01-01

Full Text Available Release kinetics of tigecycline, a potential antibiotic in treatment of osteomyelitis, from calcium hydroxyapatite (CHA, as one of the most important ceramic materials in bone tissue engineering, was investigated in this study. Tigecycline, in solid state, was mixed with CHA powder and the obtained mixture was compressed into tablets using two different pressures. These tablets were immersed in a phosphate-buffered saline solution and tigecycline release was measured by a UV-VIS spectrophotometer. The total release time was 5 or 28 days, depending on the pressure applied during compression. It was shown that there is a close relationship between pore sizes and drug release rate. The drug release kinetics was interpreted on the base of pore sizes and pore size distribution. [Projekat Ministarstva nauke Republike Srbije, br. 172026

Biosynthesis and release of proteins by isolated pulmonary Clara cells

International Nuclear Information System (INIS)

Patton, S.E.; Gilmore, L.B.; Jetten, A.M.; Nettesheim, P.; Hook, G.E.

1986-01-01

The major proteins synthesized and released by Clara cells were identified and compared with those synthesized and released by mixed lung cells. Highly purified Clara cells (85.9 +/- 2.4%) and mixed lung cells (Clara cells 4%, Type II cells 33%, granulocytes 18%, macrophages 2.7%, ciliated cells 1.2%) were isolated from rabbit lungs, incubated with Ham's F12 medium in collagen/fibronectin-coated plastic culture dishes in the presence of 35 S-methionine for periods of 4 and 18 hrs. Radiolabelled proteins were isolated from the cells and from the culture medium, electrophoresed on polyacrylamide gels in the presence of SDS under reducing conditions, and then autoradiographed. After 4 and 18 hr of incubation of the Clara cells the major radiolabelled cell-associated proteins were those with molecular weights of 6, 48, and 180 Kd. The major radiolabelled proteins released by Clara cells into the medium after 4 hrs of incubation had molecular weights of 6, 48, and 180 Kd, accounting for 42, 16, and 10%, respectively, of the total extracellular protein-associated radioactivity. After 18 hr of incubation the 6 and 48 Kd proteins represented 30 and 18% of the total released radioactivity, and the relative amount of the 180 Kd protein had decreased to 3%. With the mixed lung cells, the major proteins released into the medium had molecular weights of 6 and 48 Kd. Under nonreducing conditions the 6 Kd protein released by Clara cells had an apparent molecular weight of 12 Kd. Labelling isolated Clara cells with a mixture of 14 C-amino acids also identified this low molecular weight protein as the major secretory product of the Clara cell. The 6 Kd protein did not label when the cells were incubated with 14 C-glucosamine indicating that it was not a glycoprotein. Data demonstrate the release of several proteins from isolated Clara cells but the major protein had a M.W. of 6 Kd

Correlations in metal release profiles following sorption by Lemna minor.

Science.gov (United States)

Üçüncü Tunca, Esra; Ölmez, Tolga T; Özkan, Alper D; Altındağ, Ahmet; Tunca, Evren; Tekinay, Turgay

2016-08-02

Following the rapid uptake of contaminants in the first few hours of exposure, plants typically attempt to cope with the toxic burden by releasing part of the sorbed material back into the environment. The present study investigates the general trends in the release profiles of different metal(loid)s in the aquatic macrophyte Lemna minor and details the correlations that exist between the release of metal(loid) species. Water samples with distinct contamination profiles were taken from Nilüfer River (Bursa, Turkey), Yeniçağa Lake (Bolu, Turkey), and Beyşehir Lake (Konya, Turkey) and used for release studies; 36 samples were tested in total. Accumulation and release profiles were monitored over five days for 11 metals and a metalloid ((208)Pb, (111)Cd, (52)Cr,(53)Cr,(60)Ni,(63)Cu,(65)Cu,(75)As,(55)Mn, (137)Ba, (27)Al, (57)Fe, (66)Zn,(68)Zn) and correlation, cluster and principal component analyses were employed to determine the factors that affect the release of these elements. Release profiles of the tested metal(loid)s were largely observed to be distinct; however, strong correlations have been observed between certain metal pairs (Cr/Ni, Cr/Cu, Zn/Ni) and principal component analysis was able to separate the metal(loid)s into three well-resolved groups based on their release.

Endoluminal release of ureteral ligature after hysterectomy

Directory of Open Access Journals (Sweden)

Chih-Jen Wang

2016-01-01

Full Text Available Iatrogenic ureteral injury is a well-recognized complication of abdominal total hysterectomy. We report a case of a 57-year-old female who underwent abdominal total hysterectomy for a uterine myoma and experienced severe right flank pain postoperatively. The imaging study displayed an obstruction of the right distal ureter. Under ureteroscopy, an extraluminal ligature was released with a holmium:yttrium–aluminum–garnet laser. The stenotic segment was immediately relieved. Two months later, the intravenous urogram illustrated patency of the distal ureter with regression of right hydronephrosis. There was no recurrent hydronephrosis during 1 year of follow-up.

Nitrogen and phosphorus release from organic wastes and suitability as bio-based fertilizers in a circular economy.

Science.gov (United States)

Case, S D C; Jensen, L S

2017-11-22

The drive to a more circular economy has created increasing interest in recycling organic wastes as bio-based fertilizers. This study screened 15 different manures, digestates, sludges, composts, industry by-products, and struvites. Nitrogen (N) and phosphorous (P) release was compared following addition to soil. Three waste materials were then 'upgraded' using heating and pressure (105°C at 220 kPa), alkalinization (pH 10), or sonification to modify N and P release properties, and compared in a second soil incubation. Generally, maximum N release was negatively correlated with the CN ratio of the material (r = -0.6). Composted, dried, or raw organic waste materials released less N (mean of 10.8 ± 0.5%, 45.3 ± 7.2%, and 47.4 ± 3.2% of total N added respectively) than digestates, industry-derived organic fertilizer products, and struvites (mean of 58.2 ± 2.8%, 77.7 ± 6.0%, and 100.0 ± 13.1% of total N added respectively). No analyzed chemical property or processing type could explain differences in P release. No single upgrading treatment consistently increased N or P release. However, for one raw biosolid, heating at a low temperature (105°C) with pressure did increase N release as a percentage of total N added to soil from 30% to 43%.

Influence of slow-release urea on nitrogen balance and portal-drained visceral nutrient flux in beef steers

DEFF Research Database (Denmark)

Taylor-Edwards, C C; Elam, N A; Kitts, S E

2009-01-01

Two experiments were conducted to evaluate the effects of slow-release urea (SRU) versus feed-grade urea on portal-drained visceral (PDV) nutrient flux, nutrient digestibility, and total N balance in beef steers.......Two experiments were conducted to evaluate the effects of slow-release urea (SRU) versus feed-grade urea on portal-drained visceral (PDV) nutrient flux, nutrient digestibility, and total N balance in beef steers....

Formation and release of. beta. -glucosidase by Aspergillus niger ZIMET 43 746 in correlation to process operations

Energy Technology Data Exchange (ETDEWEB)

Kerns, G; Dalchow, E; Klappach, G; Meyer, D

1986-01-01

The total formation of ..beta..-glucosidase by the wild strain of Aspergillus niger ZIMET 43 746 is non-growth-associated. In discontinuous culture the total ..beta..-glucosidase activity related to the mycelium is increasing with the age of the mycelium. The complete release of the remaining mycelial-associated ..beta..-glucosidase is dependent on the structure of the mycelium. In the cases of the mycelium forms pellets throughout the growth phase than the release of ..beta..-glucosidase is accelerated compared to the release from loosly branched mycelium. Increasing shear stress caused by increasing of the impeller speed promotes the formation of pellets.

Do soft drinks affect metal ions release from orthodontic appliances?

Science.gov (United States)

Mikulewicz, Marcin; Wołowiec, Paulina; Loster, Bartłomiej W; Chojnacka, Katarzyna

2015-01-01

The effect of orange juice and Coca Cola(®) on the release of metal ions from fixed orthodontic appliances. A continuous flow system designed for in vitro testing of orthodontic appliances was used. Orange juice/Coca Cola(®) was flowing through the system alternately with artificial saliva for 5.5 and 18.5h, respectively. The collected samples underwent a multielemental ICP-OES analysis in order to determine the metal ions release pattern in time. The total mass of ions released from the appliance into orange juice and Coca Cola(®) (respectively) during the experiment was calculated (μg): Ni (15.33; 37.75), Cr (3.604; 1.052), Fe (48.42; ≥ 156.1), Cu (57.87, 32.91), Mn (9.164; 41.16), Mo (9.999; 30.12), and Cd (0.5967; 2.173). It was found that orange juice did not intensify the release of metal ions from orthodontic appliances, whereas Coca Cola(®) caused increased release of Ni ions. Copyright © 2015 Elsevier GmbH. All rights reserved.

Fission product release assessment for end fitting failure in Candu reactor loaded with CANFLEX-NU fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Oh, Dirk Joo; Jeong, Chang Joon; Lee, Kang Moon; Suk, Ho Chun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1998-12-31

Fission product release (FPR) assessment for End Fitting Failure (EFF) in CANDU reactor loaded with CANFLEX-natural uranium (NU) fuel bundles has been performed. The predicted results are compared with those for the reactor loaded with standard 37-element bundles. The total channel I-131 release at the end of transient for EFF accident is calculated to be 380.8 TBq and 602.9 TBq for the CANFLEX bundle and standard bundle channel cases, respectively. They are 4.9% and 7.9% of total inventory, respectively. The lower total releases of the CANFLEX bundle O6 channel are attributed to the lower initial fuel temperatures caused by the lower linear element power of the CANFLEX bundle compared with the standard bundle. 4 refs., 1 fig., 4 tabs. (Author)

Fission product release assessment for end fitting failure in Candu reactor loaded with CANFLEX-NU fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Oh, Dirk Joo; Jeong, Chang Joon; Lee, Kang Moon; Suk, Ho Chun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1997-12-31

Fission product release (FPR) assessment for End Fitting Failure (EFF) in CANDU reactor loaded with CANFLEX-natural uranium (NU) fuel bundles has been performed. The predicted results are compared with those for the reactor loaded with standard 37-element bundles. The total channel I-131 release at the end of transient for EFF accident is calculated to be 380.8 TBq and 602.9 TBq for the CANFLEX bundle and standard bundle channel cases, respectively. They are 4.9% and 7.9% of total inventory, respectively. The lower total releases of the CANFLEX bundle O6 channel are attributed to the lower initial fuel temperatures caused by the lower linear element power of the CANFLEX bundle compared with the standard bundle. 4 refs., 1 fig., 4 tabs. (Author)

Uranium release from different size fractions of sediments in Hanford 300 area, Washington, USA

International Nuclear Information System (INIS)

Du Jiangkun; Bao Jianguo; Hu Qinhong; Ewing, Robert P.

2012-01-01

Stirred-flow cell tests were carried out to investigate uranium (U) release from different size fractions of sediments from the U.S. Department of Energy’s Hanford 300 Area in Washington, USA. Results show that the measured concentration of U release varies with different size fractions, with the fine-grained mass fractions (<75 μm, 75–500 μm, and 500–2000 μm) being the main U carriers. However, because the sediment is mainly composed of gravel (2000–8000 μm) materials, the gravel fraction is a non-negligible U pool. Our elution experiments give a value of 8.7% of the total U being in the gravel fraction, significantly reducing the current uncertainty in evaluating U inventory. A log–log plot of released U concentration vs. elution volume (i.e., elution time) shows a power-law relationship for all size fractions, with identical exponents for the three fine size fractions (−0.875). For the <2000 μm mass fraction, comparing our eluted U values with reported total U concentrations, we estimate that a lower bound value 8.6% of the total uranium is labile. This compares well with the previously published value of 11.8% labile U after extraction with a dilute extractant for three weeks. - Highlights: ► Stirred-flow cells were used to study U release in Hanford 300 Area sediment. ► Fine-grained size fractions have higher U concentrations. ► U in coarse fraction is less studied, but its 8.7–9.3% of total U is non-negligible. ► A power-law relationship is observed between released U and elution volume. ► About 8.6% of U in the <2 mm sediment is labile.

A simplified radionuclide source term for total-system performance assessment

International Nuclear Information System (INIS)

Wilson, M.L.

1991-11-01

A parametric model for releases of radionuclides from spent-nuclear-fuel containers in a waste repository is presented. The model is appropriate for use in preliminary total-system performance assessments of the potential repository site at Yucca Mountain, Nevada; for this reason it is simpler than the models used for detailed studies of waste-package performance. Terms are included for releases from the spent fuel pellets, from the pellet/cladding gap and the grain boundaries within the fuel pellets, from the cladding of the fuel rods, and from the radioactive fuel-assembly parts. Multiple barriers are considered, including the waste container, the fuel-rod cladding, the thermal ''dry-out'', and the waste form itself. The basic formulas for release from a single fuel rod or container are extended to formulas for expected releases for the whole repository by using analytic expressions for probability distributions of some important parameters. 39 refs., 4 figs., 4 tabs

Improved estimates of filtered total mercury loadings and total mercury concentrations of solids from potential sources to Sinclair Inlet, Kitsap County, Washington

Science.gov (United States)

Paulson, Anthony J.; Conn, Kathleen E.; DeWild, John F.

2013-01-01

Previous investigations examined sources and sinks of mercury to Sinclair Inlet based on historic and new data. This included an evaluation of mercury concentrations from various sources and mercury loadings from industrial discharges and groundwater flowing from the Bremerton naval complex to Sinclair Inlet. This report provides new data from four potential sources of mercury to Sinclair Inlet: (1) filtered and particulate total mercury concentrations of creek water during the wet season, (2) filtered and particulate total mercury releases from the Navy steam plant following changes in the water softening process and discharge operations, (3) release of mercury from soils to groundwater in two landfill areas at the Bremerton naval complex, and (4) total mercury concentrations of solids in dry dock sumps that were not affected by bias from sequential sampling. The previous estimate of the loading of filtered total mercury from Sinclair Inlet creeks was based solely on dry season samples. Concentrations of filtered total mercury in creek samples collected during wet weather were significantly higher than dry weather concentrations, which increased the estimated loading of filtered total mercury from creek basins from 27.1 to 78.1 grams per year. Changes in the concentrations and loading of filtered and particulate total mercury in the effluent of the steam plant were investigated after the water softening process was changed from ion-exchange to reverse osmosis and the discharge of stack blow-down wash began to be diverted to the municipal water-treatment plant. These changes reduced the concentrations of filtered and particulate total mercury from the steam plant of the Bremerton naval complex, which resulted in reduced loadings of filtered total mercury from 5.9 to 0.15 grams per year. Previous investigations identified three fill areas on the Bremerton naval complex, of which the western fill area is thought to be the largest source of mercury on the base

Sustained-release progesterone vaginal suppositories 1--development of sustained-release granule--.

Science.gov (United States)

Nakayama, Ayako; Sunada, Hisakazu; Okamoto, Hirokazu; Furuhashi, Kaoru; Ohno, Yukiko; Ito, Mikio

2009-02-01

Progesterone (P) is an important hormone for the establishment of pregnancy, and its administration is useful for luteal insufficiency. Considering the problems of commercially available oral and injection drugs, hospital-formulated vaginal suppositories are clinically used. However, since the half-life of P suppositories is short, it is difficult to maintain its constant blood concentration. To sustain drug efficacy and prevent side-effects, we are attempting to develop sustained-release suppositories by examining the degree of sustained-release of active ingredients. In this study, we examined the combinations of granulation methods and release systems for the preparation of sustained-release granules of P, and produced 13 types of sustained-release granules. We also examined the diameter, content, and dissolution of each type of granules, and confirmed that the sustained-release of all types of granules was satisfactory. Among the sustained-release granules, we selected granules with a content and a degree of sustained-release suitable for sustained-release suppositories.

SU-F-19A-08: Optimal Time Release Schedule of In-Situ Drug Release During Permanent Prostate Brachytherapy

International Nuclear Information System (INIS)

Cormack, R; Ngwa, W; Makrigiorgos, G; Tangutoori, S; Rajiv, K; Sridhar, S

2014-01-01

Purpose: Permanent prostate brachytherapy spacers can be used to deliver sustained doses of radiosentitizing drug directly to the target, in order to enhance the radiation effect. Implantable nanoplatforms for chemo-radiation therapy (INCeRTs) have a maximum drug capacity and can be engineered to control the drug release schedule. The optimal schedule for sensitization during continuous low dose rate irradiation is unknown. This work studies the optimal release schedule of drug for both traditional sensitizers, and those that work by suppressing DNA repair processes. Methods: Six brachytherapy treatment plans were used to model the anatomy, implant geometry and calculate the spatial distribution of radiation dose and drug concentrations for a range of drug diffusion parameters. Three state partial differential equations (cells healthy, damaged or dead) modeled the effect of continuous radiation (radiosensitivities α,β) and cellular repair (time tr) on a cell population. Radiosensitization was modeled as concentration dependent change in α,β or tr which with variable duration under the constraint of fixed total drug release. Average cell kill was used to measure effectiveness. Sensitization by means of both enhanced damage and reduced repair were studied. Results: Optimal release duration is dependent on the concentration of radiosensitizer compared to the saturation concentration (csat) above which additional sensitization does not occur. Long duration drug release when enhancing α or β maximizes cell death when drug concentrations are generally over csat. Short term release is optimal for concentrations below saturation. Sensitization by suppressing repair has a similar though less distinct trend that is more affected by the radiation dose distribution. Conclusion: Models of sustained local radiosensitization show potential to increase the effectiveness of radiation in permanent prostate brachytherapy. INCeRTs with high drug capacity produce the greatest

Fission product release from TRIGA-LEU reactor fuels

International Nuclear Information System (INIS)

Baldwin, N.L.; Foushee, F.C.; Greenwood, J.S.

1980-01-01

Due to present international concerns over nuclear proliferation, TRIGA reactor fuels will utilize only low-enriched uranium (LEU) (enrichment <20%). This requires increased total uranium loading per unit volume of fuel in order to maintain the appropriate fissile loading. Tests were conducted to determine the fractional release of gaseous and metallic fission products from typical uranium-zirconium hydride TRIGA fuels containing up to 45 wt-% uranium. These tests, performed in late 1977 and early 1978, were similar to those conducted earlier on TRIGA fuels with 8.5 wt-% U. Fission gas release measurements were made on prototypic specimens from room temperature to 1100 deg. C in the TRIGA King Furnace Facility. The fuel specimens were irradiated in the TRIGA reactor at a low power level. The fractional releases of the gaseous nuclides of krypton and xenon were measured under steady-state operating conditions. Clean helium was used to sweep the fission gases released during irradiation from the furnace into a standard gas collection trap for gamma counting. The results of these tests on TRIGA-LEU fuel agree well with data from the similar, earlier tests on TRIGA fuel. The correlation used to calculate the release of fission products from 8.5 wt-% U TRIGA fuel applies equally well for U contents up to 45 wt-%. (author)

Activity release from the damaged spent VVER-fuel during long-term wet storage

International Nuclear Information System (INIS)

Slonszki, E.; Hozer, Z.; Pinter, T.; Baracska Varju, I.

2010-01-01

An ex-core fuel damage incident took place at Unit 2 of Paks Nuclear Power Plant in Hungary on the 10 th April 2003. After this event the damaged fuel assemblies were stored under water for four years. During wet storage a continuous activity release was observed. The evaluation of the measured activity concentration showed that the UO 2 mass released from the fuel into the coolant was ∼ 1.8% of the total fuel mass. Furthermore this paper contains the calculation methods and the calculated activity release of the main analysed isotopes. (orig.)

Global Collective Dose Commitments from Release of Long-Lived Radionuclides

DEFF Research Database (Denmark)

Gjørup, H. L.

1977-01-01

The concept of global collective dose commitment as a measure of total detriment from the release of radioactivity to the environment is outlined. Estimates are given of global collective dose commitments resulting from the release of 14C and uranium daughter products from the nuclear fuel cycle...... that the use of global collective dose commitments in differential cost-benefit analysis can lead to questionable results. In differential cost-benefit analysis it is suggested that population exposures should not simply be integrated irrespective of their time of occurrence, but that a certain discount rate...

Evaluation of Slow Release Fertilizer Applying Chemical and Spectroscopic methods

International Nuclear Information System (INIS)

AbdEl-Kader, A.A.; Al-Ashkar, E.A.

2005-01-01

Controlled-release fertilizer offers a number of advantages in relation to crop production in newly reclaimed soils. Butadiene styrene latex emulsion is one of the promising polymer for different purposes. In this work, laboratory evaluation of butadiene styrene latex emulsion 24/76 polymer loaded with a mixed fertilizer was carried out. Macro nutrients (N, P and K) and micro-nutrients(Zn, Fe, and Cu) were extracted by basic extract from the polymer fertilizer mixtures. Micro-sampling technique was investigated and applied to measure Zn, Fe, and Cu using flame atomic absorption spectrometry in order to overcome the nebulization difficulties due to high salt content samples. The cumulative releases of macro and micro-nutrients have been assessed. From the obtained results, it is clear that the release depends on both nutrients and polymer concentration in the mixture. Macro-nutrients are released more efficient than micro-nutrients of total added. Therefore it can be used for minimizing micro-nutrients hazard in soils

Blood histamine release: A new allergy blood test

International Nuclear Information System (INIS)

Faraj, B.A.; Gottlieb, G.R.; Camp, V.M.; Lollies, P.

1985-01-01

Allergen-mediated histamine release from human leukocytes represents an important model for in vitro studies of allergic reactions. The purpose of this study was to determine whether the measurement of histamine released in allergic patients (pts) by radioenzymatic assay following mixing of their blood with common allergens represents a reliable index for diagnosis of atopic allergy. Three categories of allergies were used: (1) housedust and mite; (2) cat and dog dander; (3) trees and grasses and ragweed mixture. The presence of allergy was established by intradermal skin testing in the study group of 82 pts. Significant atopy was defined as ≥ 3+ (overall range 0-4 +, negative to maximum) on skin testing. The test was carried out in tubes with 0.5 ml heparinized blood, 0.5 ml tris albumin buffer, and one of the allergens (60-100 PNU/ml). In 20 controls without allergy, there always was ≤ 4% histamine release (normal response). A significant allergen-mediated histamine release, ranging from 12 to 30% of the total blood histamine content, was observed in 96% of the pts with skin test sensitivity of ≥ 3+. There was good agreement between skin testing and histamine release in terms of the allergen causing the response. Thus, measurement of histamine release in blood in response to allergen challenge represents a clinically useful in vitro test for the diagnosis of atopic allergy. Because data can be obtained from a single sample and are highly quantitative, this new method should have application to the longitudinal study of allergic pts and to the assessment of interventions

Consequences of severe radioactive releases to Nordic Marine environment

Energy Technology Data Exchange (ETDEWEB)

Iosjpe, M. [Norwegian Radiation Protection Authority (NRPA) (Norway); Isaksson, M. [Univ. of Gothenburg (Sweden); Joensen, H.P. [Froskaparsetur Foeroya. Faroe Islands, Torshavn (Denmark); Lahtinen, J. [Radiation and Nuclear Safety Authority (Finland); Logemann, K. [Univ. of Iceland (Iceland); Palsson, S.E. [Geislavarnir Rikisins (Iceland); Roos, P. [Technical Univ. of Denmark. Risoe DTU, Roskilde (Denmark); Suolanen, V. [Technical Research Centre of Finland (Finland)

2013-02-15

chosen release fractions in the study were: iodine 20% (of the total core inventory), caesium 10%, tellurium 10%, strontium 0.5%, ruthenium 0.5%. The considered release event to marine environment were assumed to start ten hours after shutdown of the reactor. Total released amounts of the most important nuclides were estimated to be: 4.85{center_dot}10{sup 17} Bq (I-131), 7.29{center_dot}10{sup 16} Bq (Cs-134) and 4.17{center_dot}10{sup 16} Bq (Cs-137). Due to the highly contaminated sea food, the arising doses to human from a hypothetical severe nuclear power plant accident would be high especially in local sea area. Based on preliminary results, annual individual doses could be ten to some hundreds of millisieverts from local sea area. The most important nuclides were Cs-134, Cs-137 and I-131 causing 96% of the total ingestion dose. In the Baltic Sea area, the arising doses from a severe nuclear power plant accident assumed to happen e.g. at Gulf of Finland, would be about 1/10000 compared to doses in the local sea area. Thus the arising maximum annual individual dose for fish pathway is in the level of 0.1 mSv in the Baltic Sea area. Submarine accident assumed to happen at Icelandic waters, has been analysed in the study. The calculated collective dose rates to man as well as doses to a critical group are significantly lower than doses from natural sources. However, in local considerations dose-rates are significantly higher than the negligible component to the annual individual dose obtained from natural sources (UNSCEAR, 2000) and, therefore, have to be taken into consideration during evaluation of the accident consequences. (Author)

Consequences of severe radioactive releases to Nordic Marine environment

International Nuclear Information System (INIS)

Iosjpe, M.; Isaksson, M.; Joensen, H.P.; Lahtinen, J.; Logemann, K.; Palsson, S.E.; Roos, P.; Suolanen, V.

2013-02-01

release fractions in the study were: iodine 20% (of the total core inventory), caesium 10%, tellurium 10%, strontium 0.5%, ruthenium 0.5%. The considered release event to marine environment were assumed to start ten hours after shutdown of the reactor. Total released amounts of the most important nuclides were estimated to be: 4.85·10 17 Bq (I-131), 7.29·10 16 Bq (Cs-134) and 4.17·10 16 Bq (Cs-137). Due to the highly contaminated sea food, the arising doses to human from a hypothetical severe nuclear power plant accident would be high especially in local sea area. Based on preliminary results, annual individual doses could be ten to some hundreds of millisieverts from local sea area. The most important nuclides were Cs-134, Cs-137 and I-131 causing 96% of the total ingestion dose. In the Baltic Sea area, the arising doses from a severe nuclear power plant accident assumed to happen e.g. at Gulf of Finland, would be about 1/10000 compared to doses in the local sea area. Thus the arising maximum annual individual dose for fish pathway is in the level of 0.1 mSv in the Baltic Sea area. Submarine accident assumed to happen at Icelandic waters, has been analysed in the study. The calculated collective dose rates to man as well as doses to a critical group are significantly lower than doses from natural sources. However, in local considerations dose-rates are significantly higher than the negligible component to the annual individual dose obtained from natural sources (UNSCEAR, 2000) and, therefore, have to be taken into consideration during evaluation of the accident consequences. (Author)

Estimate of total CO2 output from desertified sandy land in China

International Nuclear Information System (INIS)

Duan Zhenghu; Lanzhou University; Xiao Honglang; Dong Zhibao; He Xingdong; Wang Gang

2001-01-01

Soil is an important factor in regional and global carbon budgets because it serves as a reservoir of large amount of organic carbon. In our study, using remote sensing data of different periods we analyzed the development and reversion of desertification in China, calculated the variations of organic carbon contents of the desertified lands in China. The results showed that the total storage of organic carbon in 0-50cm soil layer of the desertified lands is 855Mt. In recent 40yr, the total CO 2 amount released by land desertification processes to the atmosphere was 150Mt, while the CO 2 amount sequestered by desertification reversing processes corresponded to 59MtC. Hence, the net CO 2 amount released from desertified lands of China corresponded to 91MtC, about 68.42% of the 133MtC of annual CO 2 release in the global temperate and frigid zones. Simultaneously, it indicated that CO 2 amount sequestered by desertification reversing processes in desertified land had greater potential than the other soils. (Author)

ACRR fission product release tests: ST-1 and ST-2

International Nuclear Information System (INIS)

Allen, M.D.; Stockman, H.W.; Reil, K.O.; Grimley, A.J.; Camp, W.J.

1988-01-01

Two experiments (ST-1 and ST-2) have been performed in the Annular Core Research Reactor (ACRR) at Sandia National Laboratories (SNLA) to obtain time-resolved data on the release of fission products from irradiated fuels under light water reactor (LWR) severe accident conditions. Both experiments were conducted in a highly reducing environment at maximum fuel temperatures of greater than 2400 K. These experiments were designed specifically to investigate the effect of increased total pressure on fission product release; ST-1 was performed at approximately 0.16 MPa and ST-2 was run at 1.9 MPa, whereas other parameters were matched as closely as possible. Release rate data were measured for Cs, I, Ba, Sr, Eu, Te, and U. The release rates were higher than predicted by existing codes for Ba, Sr, Eu, and U. Te release was very low, but Te did not appear to be sequestered by the zircaloy cladding; it was evenly distributed in the fuel. In addition, in posttest analysis a unique fuel morphology (fuel swelling) was observed which may have enhanced fission product release, especially in the high pressure test (ST-2). These data are compared with analytical results from the CORSOR correlation and the VICTORIA computer model

Nitrogen mineralization and volatilization from controlled release urea fertilizers in selected malaysian soils

International Nuclear Information System (INIS)

Singh, K.J.K.A.; Yusop, M.K.; Oad, F.C.

2017-01-01

Controlled release urea fertilizers are usually used for extended duration in supplying nitrogen. The rate of urea hydrolysis could be efficiently minimized through these fertilizers. Various controlled released fertilizers i.e Uber-10 (30%N), Meister-20 (40%N), Meister-27 (40%N), Humate Coated Urea (45%N), Duration Polymer Coated Urea Type-V (43%N), Gold-N-Sulfur Coated Urea (41%N) and common urea (46%N) were applied to inland soil series of Malaysia. The soil series investigated were: Serdang (Typic Paleudult), Munchong (Typic Hapludox), Segamat (Typic Hapludox), Selangor (Typic Tropaquept), Rengam (Typic Kandiudult) and Holyrood (Typic Kandiudult). The maximum release of ammonium (NH/sub 4/-N) was noted in Gold-N-Sulfur Coated Urea, Humate Coated Urea and common Urea over 8 weeks of incubation. However, the release of NH4-N under the influence of Duration Type-V and Uber-10 took 2nd place. The Meister-20 and Meister-27 had minimum release of NH4-N. Munchong series was efficient in releasing higher NH4-N compared to rest of soils during 8th week of incubation due to higher soil total carbon, low /sub 4/-N and total nitrogen. Ammonia (NH/sub 3/-N) loss progressively increased with unit increase in incubation week and was higher during 6th week of fertilizer application. The higher loss of NH3-N was found in common Urea. However, Meister-20, Meister-27, Duration Polymer Coated Urea Type-V and Uber-10 had lower loss of NH/sub 3/-N due to slow release property and this character could be beneficial for supplying nutrients to next season crop. (author)

Tellurium release and deposition during the TMI-2 accident

International Nuclear Information System (INIS)

Vinjamuri, K.; Osetek, D.J.; Hobbins, R.R.; Jessup, J.S.

1984-09-01

The estimated behavior of tellurium during and after the accident at the Three Mile Island Unit-2 is presented. The behavior is based on all available measurement data for /sup 129m/Te, 132 Te, stable tellurium ( 126 Te, 128 Te and 130 Te), and best estimate calculations of tellurium release and transport. The predicted release was calculated using current techniques that relate release rate to fuel temperature and holdup of tellurium in zircaloy until significant oxidation occurs. The calculated release fraction was low, approx. 7%, but the total measured release for samples analyzed to date is about 5.8%. Of the measured tellurium about 2.4, 1.8, 0.88, 0.42, 0.17 and 0.086% of core inventory were in the containment sump water, upper plenum assembly surfaces, containment solids in the sump water, makeup and purification demineralizer, containment inside surface, and the reactor primary coolant, respectively. A significant fraction (54%) of the tellurium calculated to be retained on the upper plenum surfaces (4.61% of the core inventory) was deposited during the high pressure injection of coolant at about 200 min after the reactor scram. Comparison of tellurium behavior with in-pile and out-of-pile tests strongly suggests that zircaloy holds tellurium until significant cladding oxidation occurs

Simulation and parametric study of a film-coated controlled-release pharmaceutical.

Science.gov (United States)

Borgquist, Per; Zackrisson, Gunnar; Nilsson, Bernt; Axelsson, Anders

2002-04-23

Pharmaceutical formulations can be designed as Multiple Unit Systems, such as Roxiam CR, studied in this work. The dose is administrated as a capsule, which contains about 100 individual pellets, which in turn contain the active drug remoxipride. Experimental data for a large number of single pellets can be obtained by studying the release using microtitre plates. This makes it possible to study the release of the individual subunits making up the total dose. A mathematical model for simulating the release of remoxipride from single film-coated pellets is presented including internal and external mass transfer hindrance apart from the most important film resistance. The model can successfully simulate the release of remoxipride from single film-coated pellets if the lag phase of the experimental data is ignored. This was shown to have a minor influence on the release rate. The use of the present model is demonstrated by a parametric study showing that the release process is film-controlled, i.e. is limited by the mass transport through the polymer coating. The model was used to fit the film thickness and the drug loading to the experimental release data. The variation in the fitted values was similar to that obtained in the experiments.

Digestion of thyroglobulin with purified thyroid lysosomes: preferential release of iodoamino acids

International Nuclear Information System (INIS)

Tokuyama, T.; Yoshinari, M.; Rawitch, A.B.; Taurog, A.

1987-01-01

[ 131 I]Thyroglobulin [( 131 I]Tg), prepared by either enzymatic iodination of human goiter Tg in vitro or isolation from the thyroids of rats previously injected with 131 I, was digested with a solubilized enzyme mixture prepared from purified hog thyroid lysosomes. The digestion was performed at 37 C for 24 h under nitrogen at pH 5.0 in the presence of 4 mM dithiothreitol. Under these conditions the release of free [ 131 I] iodoamino acids (MIT, DIT, T4, and T3) was quantitatively very similar to that observed with a standard pronase digestion procedure. To determine whether other amino acids in Tg were released as quantitatively as the iodoamino acids, free amino acids in the lysosomal digest were measured, and total free amino acid release was compared with a similar analysis performed after digestion of [ 131 I]Tg with 6 N HCl. Total amino acid release was much less complete than iodoamino acid release, indicating preferential release of iodoamino acids from Tg by lysosomal digestion. Analysis of the lysosomal digest by HPLC on a size exclusion column indicated that Tg was degraded to peptides with a mol wt less than 4000. Assuming that the in vitro lysosomal digestion system represents a valid model for the physiological proteolytic system that degrades Tg, the results of the present study suggest that a substantial portion of the Tg in the thyroid is not degraded to free amino acids and that peptide fragments of Tg are normally present in the thyroid. In such a case, the fate and possible physiological activity of these fragments require further elucidation

Drug release kinetic analysis and prediction of release data via polymer molecular weight in sustained release diltiazem matrices.

Science.gov (United States)

Adibkia, K; Ghanbarzadeh, S; Mohammadi, G; Khiavi, H Z; Sabzevari, A; Barzegar-Jalali, M

2014-03-01

This study was conducted to investigate the effects of HPMC (K4M and K100M) as well as tragacanth on the drug release rate of diltiazem (DLTZ) from matrix tablets prepared by direct compression method.Mechanism of drug transport through the matrices was studied by fitting the release data to the 10 kinetic models. 3 model independent parameters; i. e., mean dissolution time (MDT), mean release rate (MRR) and release rate efficacy (RE) as well as 5 time point approaches were established to compare the dissolution profiles. To find correlation between fraction of drug released and polymer's molecular weight, dissolution data were fitted into two proposed equations.All polymers could sustain drug release up to 10 h. The release data were fitted best to Peppas and Higuchi square root kinetic models considering squared correlation coefficient and mean percent error (MPE). RE and MRR were decreased when polymer to drug ratio was increased. Conversely, t60% was increased with raising polymer /drug ratio. The fractions of drug released from the formulations prepared with tragacanth were more than those formulated using the same amount of HPMC K4M and HPMC K100M.Preparation of DLTZ matrices applying HPMCK4M, HPMC K100M and tragacanth could effectively extend the drug release. © Georg Thieme Verlag KG Stuttgart · New York.

Accelerated in-vitro release testing methods for extended-release parenteral dosage forms.

Science.gov (United States)

Shen, Jie; Burgess, Diane J

2012-07-01

This review highlights current methods and strategies for accelerated in-vitro drug release testing of extended-release parenteral dosage forms such as polymeric microparticulate systems, lipid microparticulate systems, in-situ depot-forming systems and implants. Extended-release parenteral dosage forms are typically designed to maintain the effective drug concentration over periods of weeks, months or even years. Consequently, 'real-time' in-vitro release tests for these dosage forms are often run over a long time period. Accelerated in-vitro release methods can provide rapid evaluation and therefore are desirable for quality control purposes. To this end, different accelerated in-vitro release methods using United States Pharmacopeia (USP) apparatus have been developed. Different mechanisms of accelerating drug release from extended-release parenteral dosage forms, along with the accelerated in-vitro release testing methods currently employed are discussed. Accelerated in-vitro release testing methods with good discriminatory ability are critical for quality control of extended-release parenteral products. Methods that can be used in the development of in-vitro-in-vivo correlation (IVIVC) are desirable; however, for complex parenteral products this may not always be achievable. © 2012 The Authors. JPP © 2012 Royal Pharmaceutical Society.

Accelerated in vitro release testing methods for extended release parenteral dosage forms

Science.gov (United States)

Shen, Jie; Burgess, Diane J.

2012-01-01

Objectives This review highlights current methods and strategies for accelerated in vitro drug release testing of extended release parenteral dosage forms such as polymeric microparticulate systems, lipid microparticulate systems, in situ depot-forming systems, and implants. Key findings Extended release parenteral dosage forms are typically designed to maintain the effective drug concentration over periods of weeks, months or even years. Consequently, “real-time” in vitro release tests for these dosage forms are often run over a long time period. Accelerated in vitro release methods can provide rapid evaluation and therefore are desirable for quality control purposes. To this end, different accelerated in vitro release methods using United States Pharmacopoeia (USP) apparatus have been developed. Different mechanisms of accelerating drug release from extended release parenteral dosage forms, along with the accelerated in vitro release testing methods currently employed are discussed. Conclusions Accelerated in vitro release testing methods with good discriminatory ability are critical for quality control of extended release parenteral products. Methods that can be used in the development of in vitro-in vivo correlation (IVIVC) are desirable, however for complex parenteral products this may not always be achievable. PMID:22686344

Quantitative characterization of TiO2 nanoparticle release from textiles by conventional and single particle ICP-MS

Science.gov (United States)

Mackevica, Aiga; Olsson, Mikael Emil; Hansen, Steffen Foss

2018-01-01

TiO2 is ubiquitously present in a wide range of everyday items, both as an intentionally incorporated additive and naturally occurring constituent. It can be found in a wide range of consumer products, including personal care products, food contact materials, and textiles. Normal use of these products may lead to consumer and/or environmental exposure to TiO2, possibly in form of nanoparticles. The aim of this study is to perform a leaching test and apply state-of-the-art methods to investigate nano-TiO2 and total Ti release from five types of commercially available conventional textiles: table placemats, wet wipes, microfiber cloths, and two types of baby bodysuits, with Ti contents ranging from 2.63 to 1448 μg/g. Released particle analysis was performed using conventional and single particle inductively coupled plasma mass spectrometry (ICP-MS and spICP-MS), in conjunction with transmission electron microscopy (TEM), to measure total and particulate TiO2 release by mass and particle number, as well as size distribution. Less than 1% of the initial Ti content was released over 24 h of leaching, with the highest releases reaching 3.13 μg/g. The fraction of nano-TiO2 released varied among fabric types and represented 0-80% of total TiO2 release. Particle mode sizes were 50-75 nm, and TEM imaging revealed particles in sizes of 80-200 nm. This study highlights the importance of using a multi-method approach to obtain quantitative release data that is able to provide an indication regarding particle number, size distribution, and mass concentration, all of which can help in understanding the fate and exposure of nanoparticles.

News/Press Releases

Data.gov (United States)

Office of Personnel Management — A press release, news release, media release, press statement is written communication directed at members of the news media for the purpose of announcing programs...

Formulation and characterization of modified release tablets containing isoniazid using swellable polymers.

Science.gov (United States)

Akhtar, M F; Rabbani, M; Sharif, A; Akhtar, B; Saleem, A; Murtaza, G

2011-01-01

The aim of this work was to develop swellable modified release (MR) isoniazid tablets using different combinations of polyvinyl acetate (PVAc) and sodium-carboxymethylcellulose (Na-CMC). Granules were prepared by moist granulation technique and then compressed into tablets. In vitro release studies for 12 hr were carried out in dissolution media of varying pH i.e. pH 1.2, 4.5, 7.0 and 7.5. Tablets of all formulations were found to be of good physical quality with respect to appearance (width and thickness), content uniformity, hardness, weight variation and friability. In vitro release data showed that increasing total polymer content resulted in more retarding effect. Formulation with 35% polymer content exhibited zero order release profile and it released 35% of the drug in first hr, later on, controlled drug release was observed upto the 12(th) hour. Formulations with PVAc to Na-CMC ratio 20:80 exhibited zero order release pattern at levels of studied concentrations, which suggested that this combination can be used to formulate zero order release tablets of water soluble drugs like isoniazid. Korsmeyer-Peppas modeling of drug release showed that non-Fickian transport is the primary mechanism of isoniazid release from PVAc and Na-CMC based tablets. The value of mean dissolution time decreased with the increase in the release rate of drug clearly showing the retarding behavior of the swellable polymers. The application of a mixture of PVAc to Na-CMC in a specific ratio may be feasible to formulate zero order release tablets of water soluble drugs like isoniazid.

Activity release from the damaged spent VVER-fuel during long-term wet storage

Energy Technology Data Exchange (ETDEWEB)

Slonszki, E.; Hozer, Z. [Hungarian Academy of Sciences, KFKI Atomic Energy Research Inst., Budapest (Hungary); Pinter, T.; Baracska Varju, I. [Nuclear Power Plant Paks, Paks (Hungary)

2010-07-01

An ex-core fuel damage incident took place at Unit 2 of Paks Nuclear Power Plant in Hungary on the 10{sup th} April 2003. After this event the damaged fuel assemblies were stored under water for four years. During wet storage a continuous activity release was observed. The evaluation of the measured activity concentration showed that the UO{sub 2} mass released from the fuel into the coolant was {approx} 1.8% of the total fuel mass. Furthermore this paper contains the calculation methods and the calculated activity release of the main analysed isotopes. (orig.)

Applying Total Quality Leadership to an aviation squadron

OpenAIRE

Knighton, Edward L.; Melnick, Norbert F.

1991-01-01

Approved for public release; distribution is unlimited The implementation of Total Quality Leadership has been successful in several Department of Defense organizations. However, an aviation squadron provides an unique environment for the application of TQL. This thesis describes an adaptation of the NPRDC TQM process improvement model for a fleet squadron which includes the Shewart Cycle, customer supplier relationships, and mission deployment. Dr. W. Edwards Deming's 14...

Nickel and Cobalt Release From Children's Toys Purchased in Denmark and the United States

DEFF Research Database (Denmark)

Jensen, P.; Hamann, Dathan; Hamann, Carsten R.

2014-01-01

from children's toys. Methods : We purchased 212 toys in 18 different retail and online stores in the United States and Denmark. Nickel and cobalt release was tested using the dimethylglyoxime and cobalt screening spot tests. Results : A total of 73 toys (34.4%) released nickel, and none released......Background : Nickel is the most common allergen detected by patch testing in children. There is an increasing number of cases in children who have not had exposure to piercing. Although the clinical relevance of nickel patch test reactions in children is sometimes uncertain, continued vigilance...

Sulfur Release during Alternative fuels Combustion in Cement Rotary Kilns

DEFF Research Database (Denmark)

Cortada Mut, Maria del Mar

fuel with the bed material, heating up of a particle, 5 iv devolatilization, char combustion, the reactions between CaSO 4 and the different reducing agents, and the oxidation of the volatiles gases in the free board. The main reducing agents are CO, CH 4 and H 2 , which are introduced under the bed...... are of high importance for SO 2 release because it is shown that introducing the same total amount of gas, the highest reducing agent concentration fo r a short period released a higher total SO 2 amount compared to the lowest concentration during a long period. A mathematical reaction based model...... but the effect of sulfur content in the bed cannot be predicted. Further development regarding particle motion according to the rotational speed may be needed. Furthermore, a model for predicting the tendency of build-ups for a kiln system is developed based on the prediction of SO 3 and Cl concentrations...

Ecological reconcentrations of radionuclides released by nuclear industry

International Nuclear Information System (INIS)

Schaeffer, R.

1977-01-01

An attempt is made to assess the relative importance of the various pathways to man by relating the doses that in the most unfavorable conditions might result from long-term environmental accumulation of the radionuclides to the doses resulting from air inhalation or water ingestion only. For instance, for 131 I released in air, the ratio may reach a value of 1,000 from milk consumption and 3 from consumption of leafy vegetables. For 137 Cs released in water, the ratio may reach a value of 20 from the food chain contamination and 500 on account of external exposure from sediments. However, in spite of these high ratios, the absolute values of the total doses received remain low since the exposures corresponding to air inhalation or water ingestion are usually unsignificant. For water releases, attention is called on the misinterpretations that might result from generalizing the concentration factor values reported in the literature on account of their variations both in time and space: this factor ought to be calculated for each point of the environment on the basis of hydrological data [fr

Thyroid remnant ablation using 1,110 MBq of I-131 after total thyroidectomy. Regulatory considerations on release of patients after unsealed radioiodine therapy

International Nuclear Information System (INIS)

Kusakabe, Kiyoko; Yokoyama, Kunihiko; Ito, Koichi

2012-01-01

This study was undertaken to measure the radiation exposure level of caregivers following outpatient NaI (I-131) 1,110 MBq therapy for remnant thyroid ablation after total thyroidectomy in patients with differentiated thyroid cancer, and to evaluate the influence of activities of daily living on radiation exposure level, with the goal of proposing an optimum method of I-131 therapy. The study included 37 patients with differentiated thyroid cancer, who had undergone total thyroidectomy and received outpatient based remnant thyroid ablation using NaI (I-131) 1,110 MBq, who were satisfying the following requirements: patients who have no evidence of distant metastases, whose living environments were appropriate for outpatient I-131 (1,110 MBq) therapy, and patients who gave written informed consent. The dose rate at a distance of 1 m from the body surface of the patient at the moment of release was measured using survey meters of the GM type or ionization chamber type. The dose level for the caregiver was measured with a personal dosimeter in all cases. The dose rate at a distance of 1 m from the patient's body surface 1 h after I-131 administration was in the range of 29-115 μSv/h (mean 63.8 μSv/h). The 7-day cumulative effective dose of caregivers was 0.11±0.08 mSv, on an average, in 34 dosimeters. In 31 of 34 dosimeters, cumulative effective dose of caregivers was below 0.2 mSv. Dose levels exceeding 0.2 mSv were recorded in 3 cases (0.21, 0.35 and 0.43 mSv in one case each). These results suggest that the exposure level of family members (caregiver and others) was minimal and is lower than the radiation levels affecting human environments. Outpatient-based remnant thyroid ablation with I-131 (1,110 MBq) performed after total thyroidectomy in patients with differentiated thyroid cancer is safe if applied in accordance with the appropriate supervision and guidance by experts with certain qualifications. (author)

Hydraulic running and release tool with mechanical emergency release

International Nuclear Information System (INIS)

Baker, S.F.

1991-01-01

This patent describes a setting tool for connection in a well string to position a tubular member in a well bore. It comprises: a mandrel adapted to be connected to the well string; an outer sleeve surrounding the mandrel and releasably secured thereto; a latch nut releasably connected to the outer sleeve; piston means sealingly engaging the mandrel; shear means releasably securing the piston to the latch nut to maintain the latch nut releasably connected to the tubular member; the mandrel having port means for conducting fluid pressure from the well string to release the piston means from and the latch nut; cooperating engageable surfaces on the piston and latch nut to reengage them together after the piston moves a predetermined longitudinal distance relative to the latch nut; and additional cooperating engageable surfaces on the latch nut and the outer sleeve which are engageable when the piston and engaged latch nut are moved a predetermined additional longitudinal distance by fluid pressure to secure the engaged piston and latch nut with the outer sleeve for retrieval along with the mandrel from the well bore

Effect of total flavonoid in rabdosia rubescens on tolerant mice models under cerebral anoxia

Directory of Open Access Journals (Sweden)

Le Kang

2017-12-01

Conclusion: The total flavonoid in rabdosia rubescens can stimulate an endogenous protective mechanism by inducing the release of low levels of cytokines NO and NOS, which reduces the release of serum NSE, relieves the brain tissue ischemia-reperfusion injury, and further improves the protection effect of ischemic preconditioning on brain injury. The damage of brain tissue ischemia and reperfusion, and further improve the ischemia Protective effect of preconditioning on brain injury.

Experiments to Measure Hydrogen Release from Graphite Walls During Disruptions in DIII-D

International Nuclear Information System (INIS)

Hollmann, E.M.; Pablant, N.A.; Rudakov, D.L.; Boedo, J.A.; Brooks, N.H.; Jernigan, Thomas C.; Pigarov, A.Y.

2009-01-01

Spectroscopy and wall the bake-out measurements are performed in the DIII-D tokamak to estimate the amount of hydrogen stored in and released from the walls during disruptions. Both naturally occurring disruptions and disruptions induced by massive gas injection (MGI) are investigated. The measurements indicate that both types of disruptions cause a net release of order 10(21) hydrogen (or deuterium) atoms from the graphite walls. This is comparable to the pre-disruptions plasma particle inventory, so the released hydrogen is important for accurate modeling of disruptions. However, the amount of hydrogen released is small compared to the total saturated wall inventory of order 10(22)-10(23), So it appears that many disruptions are necessary to provide full pump-out of the vessel walls. (C) 2009 Published by Elsevier B.V.

Effect of buffer thickness on the retardation of radionuclide release from the high-level waste repository

International Nuclear Information System (INIS)

Cho, Won Jin; Lee, Jae Owan; Kang, Chul Hyung; Han, Kyung Won

2000-12-01

The radionuclide release from buffer in the high-level waste repository to the surrounding host rock was assessed, and the effect of the radial buffer thickness on the release rate was analyzed. The total release rates decrease sharply with increasing radial buffer thickness up to 0.25 m, and decrease moderately at the buffer thickness between 0.25 m and 0.5 m. But increasing the radial buffer thickness beyond 0.5 m has little effect in reducing radionuclide release. Therefore a radial buffer thickness between 0.25 m and 0.5 m is sufficient based on the viewpoint of radionuclide retention

Determination of total gas in lithium tritide-deuteride compounds

International Nuclear Information System (INIS)

Smith, M.E.; Koski, N.L.; Waterbury, G.R.

1979-04-01

Lithium tritide--deuteride samples are enclosed in a copper foil and decomposed by heating to 850 0 C in a copper reaction tube in vacuum. The temperature and pressure of the evolved gas, collected in a measured volume using a Toepler pump, are measured to determine the total moles of gas released from the sample. The gas is transferred to a removable sample bulb and, if required, analyzed for gaseous constituents by mass spectrometry. Based on 14 total gas determinations for a lithium deuteride sample, the calculated relative standard deviation was 1.0% and the estimated bias was <2.5%

Decoupling of arsenic and iron release from ferrihydrite suspension under reducing conditions: a biogeochemical model

Directory of Open Access Journals (Sweden)

Morin Guillaume

2007-11-01

Full Text Available Abstract High levels of arsenic in groundwater and drinking water are a major health problem. Although the processes controlling the release of As are still not well known, the reductive dissolution of As-rich Fe oxyhydroxides has so far been a favorite hypothesis. Decoupling between arsenic and iron redox transformations has been experimentally demonstrated, but not quantitatively interpreted. Here, we report on incubation batch experiments run with As(V sorbed on, or co-precipitated with, 2-line ferrihydrite. The biotic and abiotic processes of As release were investigated by using wet chemistry, X-ray diffraction, X-ray absorption and genomic techniques. The incubation experiments were carried out with a phosphate-rich growth medium and a community of Fe(III-reducing bacteria under strict anoxic conditions for two months. During the first month, the release of Fe(II in the aqueous phase amounted to only 3% to 10% of the total initial solid Fe concentration, whilst the total aqueous As remained almost constant after an initial exchange with phosphate ions. During the second month, the aqueous Fe(II concentration remained constant, or even decreased, whereas the total quantity of As released to the solution accounted for 14% to 45% of the total initial solid As concentration. At the end of the incubation, the aqueous-phase arsenic was present predominately as As(III whilst X-ray absorption spectroscopy indicated that more than 70% of the solid-phase arsenic was present as As(V. X-ray diffraction revealed vivianite Fe(II3(PO42.8H2O in some of the experiments. A biogeochemical model was then developed to simulate these aqueous- and solid-phase results. The two main conclusions drawn from the model are that (1 As(V is not reduced during the first incubation month with high Eh values, but rather re-adsorbed onto the ferrihydrite surface, and this state remains until arsenic reduction is energetically more favorable than iron reduction, and (2 the

Multi-unit dosage formulations of theophylline for controlled release applications.

Science.gov (United States)

Uhumwangho, Michael U; Okor, Roland S

2007-01-01

The study was carried out to investigate the drug release profiles of multi-unit dosage formulations of theophylline consisting of both the fast and slow release components in a unit dose. The fast release component consisted of conventional granules of theophylline formed by mixing the drug powder with starch mucilage (20% w/v) while the slow release component consisted of wax granulations of theophylline formed by triturating the drug powder with a melted Carnauba wax (drug:wax ratio, 4:1). The granules were either filled into capsules or tabletted. In the study design, the drug release characteristics of the individual fast or slow release particles were first determined separately and then mixed in various proportions for the purpose of optimizing the drug release profiles. The evaluating parameters were the prompt release in the first 1 h (mp), the maximum release (m infinity) and the time to attain it (t infinity). Total drug content in each capsule or tablet was 300 mg and two of such were used in dissolution studies. The release kinetics and hence the release mechanism was confirmed by measuring the linear regression coefficient (R2 values) of the release data. The release kinetics was generally most consistent with the Higuchi square root of time relationship (R2 = 0.95). indicating a diffusion-controlled mechanism. The mp (mg) and t infinity (h) values for capsules and tablets of the conventional granules were (420 mg, 3 h) and (348 mg, 5 h), respectively, while for the capsules and tablets of the wax granulations mp and t infinity values were (228 mg, 9 h) and (156 mg, 12 h), respectively, indicating that a combination of wax granulation and tableting markedly retarded drug release. In the multi-unit dose formulations where the conventional and wax granulations were mixed in the ratios 2:1, 1:1 and 1:2 (conventional: matrix), the m infinity and t infinity values for the capsules were (378 mg, 6 h), (326 mg, 6 h) and (272 mg, 7 h), reSpectively. The

Large scientific releases

International Nuclear Information System (INIS)

Pongratz, M.B.

1981-01-01

The motivation for active experiments in space is considered, taking into account the use of active techniques to obtain a better understanding of the natural space environment, the utilization of the advantages of space as a laboratory to study fundamental plasma physics, and the employment of active techniques to determine the magnitude, degree, and consequences of artificial modification of the space environment. It is pointed out that mass-injection experiments in space plasmas began about twenty years ago with the Project Firefly releases. Attention is given to mass-release techniques and diagnostics, operational aspects of mass release active experiments, the active observation of mass release experiments, active perturbation mass release experiments, simulating an artificial modification of the space environment, and active experiments to study fundamental plasma physics

Colloid Release from Soil Aggregates

DEFF Research Database (Denmark)

Vendelboe, Anders Lindblad; Møldrup, Per; Schjønning, Per

2012-01-01

The content of water-dispersible colloids (WDC) has a major impact on soil functions and structural stability. In addition, the presence of mobile colloids may increase the risk of colloid-facilitated transport of strongly sorbing environmental contaminants. The WDC content was measured in 39 soils......, using laser diffraction, by agitating the samples using a wet-dispersion unit. This approach eliminated the need for long sedimentation times required by the more classical end-over-end shaking approach and provided information about the time-dependent release of WDC. The total clay content of the soils...... ranged from 0.1 to 0.44 kg kg−1. The WDC content was measured on air-dry and moist 1- to 2-mm aggregates. The WDC content at a reference time was highly correlated to the total clay content (r > 0.91, P soils. Only for two sites was the WDC content correlated to the content of clay...

Stimulatory effects of neuronally released norepinephrine on renin release in vitro

Energy Technology Data Exchange (ETDEWEB)

Matsumura, Yasuo; Kawazoe, Shinka; Ichihara, Toshio; Shinyama, Hiroshi; Kageyama, Masaaki; Morimoto, Shiro (Osaka Univ. of Pharmaceutical Sciences (Japan))

1988-10-01

Extracellular high potassium inhibits renin release in vitro by increasing calcium concentrations in the juxtaglomerular cells. The authors found that the decreased response of renin release from rat kidney cortical slices in high potassium solution changed to a strikingly increased one in the presence of nifedipine at doses over 10{sup {minus}6} M. They then examined the stimulatory effect of extracellular high potassium in the presence of nifedipine on renin release. The enhancement of release was significantly suppressed either by propranolol or by metoprolol but not by prazosin. High potassium plus nifedipine-induced increase in renin release was markedly attenuated by renal denervation. The enhancing effect was not observed when the slices were incubated in calcium-free medium. Divalent cations such as Cd{sup 2+}, Co{sup 2+}, and Mn{sup 2+} blocked this enhancement in a concentration-dependent manner. High potassium elicited an increase in {sup 3}H efflux from the slices preloaded with ({sup 3}H)-norepinephrine. The increasing effect was not influenced by nifedipine but was abolished by the removal of extracellular calcium or by the addition of divalent cations. These observations suggest to us that the high potassium plus nifedipine-induced increase in renin release from the slices is mediated by norepinephrine derived from renal sympathetic nerves and that this neuronally released norepinephrine stimulates renin release via activation of {beta}-adrenoceptors.

Probability for human intake of an atom randomly released into ground, rivers, oceans and air

Energy Technology Data Exchange (ETDEWEB)

Cohen, B L

1984-08-01

Numerical estimates are developed for the probability of an atom randomly released in the top ground layers, in a river, or in the oceans to be ingested orally by a human, and for an atom emitted from an industrial source to be inhaled by a human. Estimates are obtained for both probability per year and for total eventual probability. Results vary considerably for different elements, but typical values for total probabilities are: ground, 3 X 10/sup -3/, oceans, 3 X 10/sup -4/; rivers, 1.7 x 10/sup -4/; and air, 5 X 10/sup -6/. Probabilities per year are typcially 1 X 10/sup -7/ for releases into the ground and 5 X 10/sup -8/ for releases into the oceans. These results indicate that for material with very long-lasting toxicity, it is important to include the pathways from the ground and from the oceans.

Source Release Modeling for the Idaho National Engineering and Environmental Laboratory's Subsurface Disposal Area

International Nuclear Information System (INIS)

Becker, B.H.

2002-01-01

A source release model was developed to determine the release of contaminants into the shallow subsurface, as part of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) evaluation at the Idaho National Engineering and Environmental Laboratory's (INEEL) Subsurface Disposal Area (SDA). The output of the source release model is used as input to the subsurface transport and biotic uptake models. The model allowed separating the waste into areas that match the actual disposal units. This allows quantitative evaluation of the relative contribution to the total risk and allows evaluation of selective remediation of the disposal units within the SDA

Slow-release urea in supplement fed to beef steers

Directory of Open Access Journals (Sweden)

Ana Paula Gonçalves

2015-02-01

Full Text Available Replacing regular urea (RU by slow-release urea (SRU at two levels of non-protein nitrogen (NPN in concentrate, offered with low-quality roughage, was evaluated in beef steers on dry matter intake (DMI, ruminal fermentation parameters, plasma urea nitrogen (PUN, total tract apparent digestibility of diets and in situ degradability of nitrogen sources. Eight ruminally cannulated steers were allocated into two 4x4 Latin squares, totalizing four treatments: 40 NPN/0 SRU: 40% of concentrate crude protein (CP as NPN, resulting from 0% of SRU and 100% of RU; 40 NPN/50 SRU: 40% of concentrate CP as NPN, resulting from 50% of SRU and 50% of RU; 40 NPN/100 SRU: 40% of concentrate CP as NPN, resulting from 100% of SRU and 0% of RU; 80 NPN/100 SRU: 80% of concentrate CP as NPN, resulting from 100% of SRU and 0% of RU. Results showed that partial substitution of regular urea by slow-release urea did not alter dry matter intake, pattern of ruminal fermentation or plasma urea nitrogen concentrations and increased the total tract apparent digestibility of crude protein in steers diets. The increase in non-protein nitrogen content in crude protein of the concentrate could compromise feed intake and the efficiency of nutrient utilization in the steers fed complete diets based on low quality forage.

No positive effect of autologous platelet gel after total knee arthroplasty

NARCIS (Netherlands)

Peerbooms, Joost C.; de Wolf, Gideon S.; Colaris, Joost W.; Bruijn, Daniël J.; Verhaar, Jan A. N.

2009-01-01

Activated platelets release a cocktail of growth factors, some of which are thought to stimulate repair. We investigated whether the use of autologous platelet gel (PG) in total knee arthroplasty (TKA) would improve wound healing and knee function, and reduce blood loss and the use of analgesics.

Comparative assessment of in vitro release kinetics of calcitonin polypeptide from biodegradable microspheres.

Science.gov (United States)

Prabhu, Sunil; Sullivan, Jennifer L; Betageri, Guru V

2002-01-01

The objective of our study was to compare the in vitro release kinetics of a sustained-release injectable microsphere formulation of the polypeptide drug, calcitonin (CT), to optimize the characteristics of drug release from poly-(lactide-co-glycolide) (PLGA) copolymer biodegradable microspheres. A modified solvent evaporation and double emulsion technique was used to prepare the microspheres. Release kinetic studies were carried out in silanized tubes and dialysis bags, whereby microspheres were suspended and incubated in phosphate buffered saline, sampled at fixed intervals, and analyzed for drug content using a modified Lowry protein assay procedure. An initial burst was observed whereby about 50% of the total dose of the drug was released from the microspheres within 24 hr and 75% within 3 days. This was followed by a period of slow release over a period of 3 weeks in which another 10-15% of drug was released. Drug release from the dialysis bags was more gradual, and 50% CT was released only after 4 days and 75% after 12 days of release. Scanning electron micrographs revealed spherical particles with channel-like structures and a porous surface after being suspended in an aqueous solution for 5 days. Differential scanning calorimetric studies revealed that CT was present as a mix of amorphous and crystalline forms within the microspheres. Overall, these studies demonstrated that sustained release of CT from PLGA microspheres over a 3-week period is feasible and that release of drug from dialysis bags was more predictable than from tubes.

Accumulation and release of 99Tc by a macrophyte of the Yenisei River (Elodea canadensis) in laboratory experiments

International Nuclear Information System (INIS)

Bolsunovsky, A.; Bondareva, L.

2008-01-01

The study addresses 99 Tc accumulation and release by Elodea canadensis, one of the abundant species of submerged plants in the Yenisei River. 99 Tc in water samples of the 'Elodea - Yenisei River water' model system and in the biomass fractions was measured using a liquid scintillation analyzer. Experiments on accumulation of 99 Tc by Elodea showed that 99 Tc activity concentration can reach 120±6 Bq/g dry wt, with the concentration factor for 99 Tc 2700±500 l/kg dry wt. In experiments on 99 Tc release, over 504 hours about 82% of the total 99 Tc activity was released into the water from the plant; most of 99 Tc was released within the first 192 hours. The data obtained using sequential chemical fractionation of biomass confirmed the experimental data on 99 Tc release, which suggested that most of the biomass-bound 99 Tc was adsorbed on the surface of Elodea. 99 Tc tightly bound to biomass (fractions of organics and mineral residue) constituted just 17% of the total 99 Tc activity. (author)

Integrated environmental modeling system for noble gas releases at the Savannah River Plant

International Nuclear Information System (INIS)

Cooper, R.E.

1973-01-01

The Savannah River Plant (SRP) is a large nuclear complex engaged in varied activities and is the AEC's major site for the production of weapons material. As a result of these activities, there are continuous and intermittent releases of radioactive gases to the atmosphere. Of these releases, the noble gases constitute about 11 percent of the total man-rem exposure to the population out to a distance of 100 km. Although SRP has an extensive radiological monitoring program, an environmental modeling system is necessary for adequately estimating effects on the environment. The integrated environmental modeling system in use at SRP consists of a series of computer programs that generate and use a library of environmental effects data as a function of azimuth and distance. Annual average atmospheric dispersion and azimuthal distribution of material assumed to be released as unit sources is estimated from a 2-year meteorological data base--assuming an arbitrary point of origin. The basic library of data consists of: ground-level concentrations according to isotope, and whole body gamma dose calculations that account for the total spatial distribution at discrete energy levels. These data are normalized to tritium measurements, and are subsequently used to generate similar library data that pertain to specific source locations, but always with respect to the same population grid. Thus, the total additive effects from all source points, both on- and off-site, can be estimated. The final program uses the library data to estimate population exposures for specified releases and source points for the nuclides of interest (including noble gases). Multiple source points are considered within a single pass to obtain the integrated effects from all sources

MODIFIED TECHNIQUE OF TOTAL LARYNGECTOMY

Directory of Open Access Journals (Sweden)

Predrag Spirić

2010-12-01

Full Text Available Surgical technique of total laryngectomy is well presented in many surgical textbooks. Essentially, it has remained the same since Gluck an Soerensen in 1922 described all its details. Generally, it stresses the U shape skin incision with releasing laryngeal structures and removing larynx from up to down. Further, pharyngeal reconstruction is performed with different kinds of sutures in two or more layers and is finished with skin suture and suction drainage. One of worst complications following this surgery is pharyngocutaneous fistula (PF. Modifications proposed in this this article suggests vertical skin incision with larynx removal from below upwards. In pharyngeal reconstruction we used the running locked suture in submucosal plan with „tobacco sac“ at the end on the tongue base instead of traditional T shaped suture. Suction drains were not used.The aim of study was to present the modified surgical technique of total laryingectomy and its impact on hospital stay duration and pharyngocutanous fistula formation. In this randomized study we analyzed 49 patients operated with modified surgical technique compared to 49 patient operated with traditional surgical technique of total laryngectomy. The modified technique of total laryngectomy was presented. Using modified technique we managed to decrease the PF percentage from previous 20,41% to acceptable 8,16% (p=0,0334. Also, the average hospital stay was shortened from 14,96 to 10,63 days (t =-2.9850; p=0.0358.The modified technique of total laryngectomy is safe, short and efficient surgical intervention which decreases the number of pharyngocutaneos fistulas and shortens the hospital stay.

PWR-GALE, Radioactive Gaseous Release and Liquid Release from PWR

International Nuclear Information System (INIS)

Chandrasekaran, T.; Lee, J.Y.; Willis, C.A.

1988-01-01

1 - Description of program or function: The PWR-GALE (Boiling Water Reactor Gaseous and Liquid Effluents) Code is a computerized mathematical model for calculating the release of radioactive material in gaseous and liquid effluents from pressurized water reactors (PWRs). The calculations are based on data generated from operating reactors, field tests, laboratory tests, and plant-specific design considerations incorporated to reduce the quantity of radioactive materials that may be released to the environment. 2 - Method of solution: GALE calculates expected releases based on 1) standardized coolant activities derived from ANS Standards 18.1 Working Group recommendations, 2) release and transport mechanisms that result in the appearance of radioactive material in liquid and gaseous waste streams, 3) plant-specific design features used to reduce the quantities of radioactive materials ultimately released to the environs, and 4) information received on the operation of nuclear power plants. 3 - Restrictions on the complexity of the problem: The liquid release portion of GALE uses subroutines taken from the ORIGEN (CCC-217) to calculate radionuclide buildup and decay during collection, processing, and storage of liquid radwaste. Memory requirements for this part of the program are determined by the large nuclear data base accessed by these subroutines

Cold urticaria. Dissociation of cold-evoked histamine release and urticara following cold challenge.

Science.gov (United States)

Keahey, T M; Greaves, M W

1980-02-01

Nine patients with acquired cold urticaria were studied to assess the effects of beta-adrenergic agents, xanthines, and corticosteroids on cold-evoked histamine release from skin in vivo. The patients, in all of whom an immediate urticarial response developed after cooling of the forearm, demonstrated release of histamine into the venous blood draining that forearm. Following treatment with aminophylline and albuterol in combination or prednisone alone, suppression of histamine release occurred in all but one patient. In some patients, this was accompanied by a subjective diminution in pruritus or buring, but there was no significant improvement in the ensuing edema or erythema. In one patient, total suppression of histamine release was achieved without any effect on whealing and erythema in response to cold challenge. Our results suggest that histamine is not central to the pathogenesis of vascular changes in acquired cold urticaria.

SUBDOSA: a computer program for calculating external doses from accidental atmospheric releases of radionuclides

International Nuclear Information System (INIS)

Strenge, D.L.; Watson, E.C.; Houston, J.R.

1975-06-01

A computer program, SUBDOSA, was developed for calculating external γ and β doses to individuals from the accidental release of radionuclides to the atmosphere. Characteristics of SUBDOSA are: doses from both γ and β radiation are calculated as a function of depth in tissue, summed and reported as skin, eye, gonadal, and total body dose; doses are calculated for releases within each of several release time intervals and nuclide inventories and atmospheric dispersion conditions are considered for each time interval; radioactive decay is considered during the release and/or transit using a chain decay scheme with branching to account for transitions to and from isomeric states; the dose from gamma radiation is calculated using a numerical integration technique to account for the finite size of the plume; and the program computes and lists the normalized air concentrations at ground level as a function of distance from the point of release. (auth)

The minimization of radioactive releases to the sea from the Tokai Reprocessing Plant

International Nuclear Information System (INIS)

Sugiyama, T.; Yoshikawa, K.; Ishii, T.

1996-01-01

The Tokai Reprocessing Plant (TRP) started hot operation in September 1977. The total amount of about 790 tU of spent fuel, generated in Japan, has been successfully reprocessed as of December 1994. Low-level liquid wastes have been treated safely with the low-level waste treatment process. The design of TRP was based on foreign technology. In the early stage of designing, the radioactivity released to the sea was estimated at approximately 2.6 TBq/day (70 Ci/day) for beta activity (except for tritium). Later, PNC added an evaporator to the process to reduce the level down to 1/100, i.e. 9.6 TBq/year (260 Ci/year) or 2.6 x 10 -2 TBq/day (0.7 Ci/day). In addition, under the supervision of the government, PNC started R and D to further decrease the radioactivity released to the sea in terms of ALARA. Aiming at reducing the activity from 9.6 TBq/year (260 Ci/year) to 1/10 of that value (i.e. 26 Ci/year), the release reduction technology development facility was added. This facility was incorporated into the low-level waste treatment process in 1980, before starting the regular operation of TRP. Since the fuel reprocessing commenced, total radioactivity discharged to the sea has been 1.9 x 10 -2 TBq (0.51 Ci) for beta activity, as of December 1994. Before incorporating the release reduction technology development facility, the yearly level was 3.7 x 10 -3 - 7.4 x 10 -3 TBq (0.1 - 0.2 Ci). After incorporation of the facility, radioactivity released to the sea was greatly decreased to non-detection levels in recent years, in spite of increasing annual reprocessing amounts. Although serious equipment failures have occurred such as the acid recovery evaporator and the dissolvers, there was no influence on radioactivity released to the sea. (author)

Effect of ginseng saponina on nicotine-induced dopamine release in the rat nucleus accumbens and striatum

International Nuclear Information System (INIS)

Kim, Sang Eun; Shim, In Sop; Chung, June Key; Lee, Myung Chul

2002-01-01

We investigated the effect of ginseng total saponin (GTS) on nicotine-induced dopamine (DA) release in the striatum and nucleus accumbens of freely moving rats using in vivo microdialysis technique. Systemic pretreatment with GTS decreased striatal DA release induced by local infusion of nicotine into the striatum. However, GTS had no effect on the resting levels of extracellular DA in the striatum. GTS also blocked nicotine-induced DA release in the nucleus accumbens. The results of the present study suggest that GTS acts on the DA terminals to prevent DA release induced by nicotine. This may reflect the blocking effect of GTS on behavioral hyperactivity induced by psychostimulants

Effect of ginseng saponina on nicotine-induced dopamine release in the rat nucleus accumbens and striatum

Energy Technology Data Exchange (ETDEWEB)

Kim, Sang Eun [Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of); Shim, In Sop [Kyunghee University, Seoul (Korea, Republic of); Chung, June Key; Lee, Myung Chul [Seoul National University College of Medicine, Seoul (Korea, Republic of)

2002-10-01

We investigated the effect of ginseng total saponin (GTS) on nicotine-induced dopamine (DA) release in the striatum and nucleus accumbens of freely moving rats using in vivo microdialysis technique. Systemic pretreatment with GTS decreased striatal DA release induced by local infusion of nicotine into the striatum. However, GTS had no effect on the resting levels of extracellular DA in the striatum. GTS also blocked nicotine-induced DA release in the nucleus accumbens. The results of the present study suggest that GTS acts on the DA terminals to prevent DA release induced by nicotine. This may reflect the blocking effect of GTS on behavioral hyperactivity induced by psychostimulants.

Chemical controls on abiotic and biotic release of geogenic arsenic from Pleistocene aquifer sediments to groundwater.

Science.gov (United States)

Gillispie, Elizabeth C; Andujar, Erika; Polizzotto, Matthew L

2016-08-10

Over 150 million people in South and Southeast Asia consume unsafe drinking water from arsenic-rich Holocene aquifers. Although use of As-free water from Pleistocene aquifers is a potential mitigation strategy, such aquifers are vulnerable to geogenic As pollution, placing millions more people at potential risk. The goal of this research was to define chemical controls on abiotic and biotic release of geogenic As to groundwater. Batch incubations of sediments with natural chemical variability from a Pleistocene aquifer in Cambodia were conducted to evaluate how interactions among arsenic, manganese and iron oxides, and dissolved and sedimentary organic carbon influenced As mobilization from sediments. The addition of labile dissolved organic carbon produced the highest concentrations of dissolved As after >7 months, as compared to sediment samples incubated with sodium azide or without added carbon, and the extent of As release was positively correlated with the percent of initial extractable Mn released from the sediments. The mode of As release was impacted by the source of DOC supplied to the sediments, with biological processes responsible for 81% to 85% of the total As release following incubations with lactate and acetate but only up to 43% to 61% of the total As release following incubations with humic and fulvic acids. Overall, cycling of key redox-active elements and organic-carbon reactivity govern the potential for geogenic As release to groundwater, and results here may be used to formulate better predictions of the arsenic pollution potential of aquifers in South and Southeast Asia.

Probabilistic consequence assessment of hydrogen sulphide releases from a heavy water plant

International Nuclear Information System (INIS)

1983-06-01

This report is the second in a series concerned with the evaluation of the consequences to the public of an accidental release of hydrogen sulphide (H 2 S) to the atmosphere following a pipe or pressure envelope failure, or some other process upset, at a heavy water plant. It consists of documentation of the code GASPROB, which has been developed to provide consequence probabilities for a range of postulated releases. The code includes mathematical simulations of initial gas behaviour upon release to the atmosphere, such as gravitational settling of a cold release and the rise of jets and flares, subsequent atmospheric dispersion under a range of weather conditions, and the toxic effects on the exposed population. The code makes use of the site-specific dispersion climatology, topography and population distribution, as well as the probabilistic lethal dose data for the released gas. Output for a given postulated release can be provided in terms of the concentration of the gas at ground level around the point of release, projected numbers of fatalities within specified areas and the projected total fatalities regardless of location. This report includes a general description of GASPROB, and specifics of the code structure, the function of each subroutine, input and output data, and the permanent data files established. Three appendices to the report contain a complete code listing, detailed subroutine descriptions and a sample output

Release behavior of triazine residues in stabilised contaminated soils

International Nuclear Information System (INIS)

Ying, G.G.; Kookana, R.S.; Mallavarpu, M.

2005-01-01

This paper reports the release behavior of two triazines (atrazine and simazine) in stabilised soils from a pesticide-contaminated site in South Australia. The soils were contaminated with a range of pesticides, especially with triazine herbicides. With multiple extractions of each soil sample with deionised water (eight in total), 15% of atrazine and 4% of simazine residues were recovered, resulting in very high concentrations of the two herbicides in leachate. The presence of small fractions of surfactants was found to further enhance the release of the residues. Methanol content up to 10% did not substantially influence the concentration of simazine and atrazine released. The study demonstrated that while the stabilisation of contaminated soil with particulate activated carbon (5%) and cement mix (15%) was effective in locking the residues of some pesticides, it failed to immobilise triazine herbicides residues completely. Given the higher water solubility of these herbicides than other compounds more effective strategies to immobilise their residues is needed. - Stabilisation of contaminated soil with a mix of activated carbon and cement may fail to immobilise some contaminants like triazines

The effect of loading solution and dissolution media on release of Diclofenac from ion exchange resins

Directory of Open Access Journals (Sweden)

"Atyabi F

2002-07-01

Full Text Available Drugs can be loaded on ion exchange resins in order to control their release. Loading of diclofenac sodium on the resin beads not only sustain its release but also reduce its gastrointestinal mucosal injury. In this study the effect of loading solution and concentration of diclofenac in loading solution on total amount of drug loaded on the resin beads (Amberlite IRA-900 and the release characteristic of drug in different media were examined. Results showed that diclofenac resin complex did not release their drug content in simulated gastric fluid but released it in simulated intestinal fluid independent of exposure time in acidic conditions. The effect of a number of parameters such as ionic strength and pH on the release characteristic of drug - resin complexes were also examined. Results showed that although ionic strength is an important factor, drug release is more affected by the pH of the media. NO ABSTRACT

Release and characteristics of fungal fragments in various conditions

Energy Technology Data Exchange (ETDEWEB)

Mensah-Attipoe, Jacob [Department of Environmental Science, University of Eastern Finland, Yliopistonranta 1D, P. O. Box 1627, FI-70211 Kuopio (Finland); Saari, Sampo [Department of Physics, Tampere University of Technology, Korkeakoulunkatu 3, 33720 Tampere (Finland); Veijalainen, Anna-Maria; Pasanen, Pertti [Department of Environmental Science, University of Eastern Finland, Yliopistonranta 1D, P. O. Box 1627, FI-70211 Kuopio (Finland); Keskinen, Jorma [Department of Physics, Tampere University of Technology, Korkeakoulunkatu 3, 33720 Tampere (Finland); Leskinen, Jari T.T. [SIB Labs, University of Eastern Finland, Yliopistonranta 1E, P. O. Box 1627, FI-70211, Kuopio (Finland); Reponen, Tiina, E-mail: reponeta@ucmail.uc.edu [Department of Environmental Science, University of Eastern Finland, Yliopistonranta 1D, P. O. Box 1627, FI-70211 Kuopio (Finland); Department of Environmental Health, University of Cincinnati, P.O. Box 670056, Cincinnati, OH 45267-0056 (United States)

2016-03-15

Intact spores and submicrometer size fragments are released from moldy building materials during growth and sporulation. It is unclear whether all fragments originate from fungal growth or if small pieces of building materials are also aerosolized as a result of microbial decomposition. In addition, particles may be formed through nucleation from secondary metabolites of fungi, such as microbial volatile organic compounds (MVOCs). In this study, we used the elemental composition of particles to characterize the origin of submicrometer fragments released from materials contaminated by fungi. Particles from three fungal species (Aspergillus versicolor, Cladosporium cladosporioides and Penicillium brevicompactum), grown on agar, wood and gypsum board were aerosolized using the Fungal Spore Source Strength Tester (FSSST) at three air velocities (5, 16 and 27 m/s). Released spores (optical size, d{sub p} ≥ 0.8 μm) and fragments (d{sub p} ≤ 0.8 μm) were counted using direct-reading optical aerosol instruments. Particles were also collected on filters, and their morphology and elemental composition analyzed using scanning electron microscopes (SEMs) coupled with an Energy-Dispersive X-ray spectroscopy (EDX). Among the studied factors, air velocity resulted in the most consistent trends in the release of fungal particles. Total concentrations of both fragments and spores increased with an increase in air velocity for all species whereas fragment–spore (F/S) ratios decreased. EDX analysis showed common elements, such as C, O, Mg and Ca, for blank material samples and fungal growth. However, N and P were exclusive to the fungal growth, and therefore were used to differentiate biological fragments from non-biological ones. Our results indicated that majority of fragments contained N and P. Because we observed increased release of fragments with increased air velocities, nucleation of MVOCs was likely not a relevant process in the formation of fungal fragments. Based

Flash release an alternative for releasing complex MEMS devices

NARCIS (Netherlands)

Deladi, S.; Krijnen, Gijsbertus J.M.; Elwenspoek, Michael Curt

2004-01-01

A novel time-saving and cost-effective release technique has been developed and is described. The physical nature of the process is explained in combination with experimental observations. The results of the flash release process are compared with those of freeze-drying and supercritical CO2

In-vitro release of anti-proliferative paclitaxel from novel balloon-expandable polycaprolactone stents

International Nuclear Information System (INIS)

Liu, Shih-Jung; Hsiao, Chao-Ying; Chen, Jan-Kan; Liu, Kuo-Sheng; Lee, Cheng-Hung

2011-01-01

This report investigated the in-vitro release characteristics of paclitaxel from novel balloon-expandable polycaprolactone stents. Polycaprolactone stents were first manufactured by a lab-made micro-injection molding machine. Paclitaxel and polylactide-polyglycolide (PLGA) copolymer were dissolved in acetonitrile and were coated onto the surface of the stents by a spray coating device, which was designed and built especially for this study. An elution method was utilized to characterize the in-vitro release characteristics of paclitaxel. The high performance liquid chromatography (HPLC) analysis showed that biodegradable stents could provide sustained release of paclitaxel for more than 70 days. Various process parameters that controlled the release rate of paclitaxel were studied. The experimental results suggested that the total period of drug release could be prolonged by adopting 75:25 PLGA copolymers, employing multi-layer coatings, and increasing the drug loading. In addition, the effectiveness of eluted paclitaxel on cell behavior was examined. The results showed that the eluted drug could effectively inhibit the proliferation of smooth muscle cells. - Research Highlights: → We investigate the in-vitro release characteristics of paclitaxel from polycaprolactone stents. → Biodegradable stents provide sustained release of paclitaxel for more than 70 days. → The eluted drug effectively inhibits the proliferation of smooth muscle cells.

Regulatory analysis on criteria for the release of patients administered radioactive material. Final report

Energy Technology Data Exchange (ETDEWEB)

Schneider, S.; McGuire, S.A.

1997-02-01

This regulatory analysis was developed to respond to three petitions for rulemaking to amend 10 CFR parts 20 and 35 regarding release of patients administered radioactive material. The petitions requested revision of these regulations to remove the ambiguity that existed between the 1-millisievert (0.1-rem) total effective dose equivalent (TEDE) public dose limit in Part 20, adopted in 1991, and the activity-based release limit in 10 CFR 35.75 that, in some instances, would permit release of individuals in excess of the current public dose limit. Three alternatives for resolution of the petitions were evaluated. Under Alternative 1, NRC would amend its patient release criteria in 10 CFR 35.75 to match the annual public dose limit in Part 20 of 1 millisievert (0.1 rem) TEDE. Alternative 2 would maintain the status quo of using the activity-based release criteria currently found in 10 CFR 35.75. Under Alternative 3, the NRC would revise the release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts (0.5 rem) TEDE.

Regulatory analysis on criteria for the release of patients administered radioactive material. Final report

International Nuclear Information System (INIS)

Schneider, S.; McGuire, S.A.

1997-02-01

This regulatory analysis was developed to respond to three petitions for rulemaking to amend 10 CFR parts 20 and 35 regarding release of patients administered radioactive material. The petitions requested revision of these regulations to remove the ambiguity that existed between the 1-millisievert (0.1-rem) total effective dose equivalent (TEDE) public dose limit in Part 20, adopted in 1991, and the activity-based release limit in 10 CFR 35.75 that, in some instances, would permit release of individuals in excess of the current public dose limit. Three alternatives for resolution of the petitions were evaluated. Under Alternative 1, NRC would amend its patient release criteria in 10 CFR 35.75 to match the annual public dose limit in Part 20 of 1 millisievert (0.1 rem) TEDE. Alternative 2 would maintain the status quo of using the activity-based release criteria currently found in 10 CFR 35.75. Under Alternative 3, the NRC would revise the release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts (0.5 rem) TEDE

Piroxicam loaded alginate beads obtained by prilling/microwave tandem technique: morphology and drug release.

Science.gov (United States)

Aquino, Rita P; Auriemma, Giulia; d'Amore, Matteo; D'Ursi, Anna Maria; Mencherini, Teresa; Del Gaudio, Pasquale

2012-07-01

This paper presents a tandem technique, based on the combination of prilling and microwave (MW) assisted treatments, to produce biodegradable alginate carriers of piroxicam with different drug controlled release behaviours. Results showed that alginate/piroxicam beads demonstrated high encapsulation efficiency and very narrow dimensional distribution. Beads dried by MW retained shape and size distribution of the hydrated particles while drying rate was strongly increased compared to convective drying processes. Moreover, different MW irradiation regimes promoted interactions between the drug and alginate matrix, affected drug polymorphism as well as inner and surface matrix structure leading to different piroxicam release profiles. High level MW irradiation led to beads with highly porous and swellable matrix able to release piroxicam in few minutes in the intestine while convective drying produced gastro-resistant beads that exhibit sustained piroxicam release (total release in 5.5h) in intestinal environment. On these results the tandem technique prilling/MW irradiation appears to be promising to obtain alginate carrier with tailored NSAIDs release depending on drug characteristics and MW irradiation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Arthroscopic treatment of patients with moderate arthrofibrosis after total knee replacement.

Science.gov (United States)

Jerosch, Joerg; Aldawoudy, Akram M

2007-01-01

The purpose of this study was to document the effect of arthroscopic management in patients with knee stiffness after total knee replacement. We present a case series study, in which 32 patients have been treated for moderate arthrofibrosis of the knee after total knee replacement, with the same regimen. We have excluded all cases of stiffness, because of infection, mechanical mal-alignment, loosening of the implants and other obvious reasons of stiffness of the knee, rather than pure arthrofibrosis. All patients first underwent a trial of conservative treatment before going for arthroscopic management. A pain catheter for femoral nerve block was inserted just before anesthesia for post-operative pain management. Arthroscopic arthrolysis of the intra-articular pathology was performed in a standardized technique with release of all fibrous bands in the suprapatellar pouch, reestablishing the medial and lateral gutter, release of the patella, resection of the remaining meniscal tissue or an anterior cyclops, if needed. Intensive physiotherapy and continuous passive motion were to start immediately post-operatively. All the patients were available for the follow up and they were evaluated using the knee society rating system. A total of 25 of the 32 procedures resulted in an improvement of the patients knee score. All the knees operated upon had intra-articular fibrous bands, hypertrophic synovitis and peri-patellar adhesions. A total of eight patients suffered from an anterior cyclops lesion and six patients showed pseudomenicus. In 19 cases a medial and lateral relapse of the patella was performed; only 5 patients got an isolated lateral release. The mean knee flexion was 119 degrees (100-130) at the end of arthroscopy and was 97 degrees (75-115) at the last follow up. The eight patients with extension lags decreased from 27 degrees (10 degrees-35 degrees) pre-operatively to 4 degrees (0-10) at time of follow up. The average knee society ratings increased from 70

Release and dispersion of overheated liquids from plutonium-nitrate transfer containers

International Nuclear Information System (INIS)

Seehars, H.D.; Hochrainer, D.; Spiekermann, M.

1985-01-01

Potential traffic accidents of 18B-transfer containers with liquid Pu-nitrate during road transportation may induce an exposure of the Ti vessel itself to a fire due to the ignition of the leaking fuel up to a critical level, causing the burst of the vessel and the more or less complete release of the contents in form of liquid aerosol particles. A report is given on experiments with the original Ti vessels and a quadrivalent Ce-nitrate solution used as a substitute with similar physico-chemical properties as the Pu-nitrate solution. Total release of mass as well as of the respirable particle mass fraction is strongly dependent on the orientation of the vessel. Maximum release, connected with a high bursting pressure and the total destruction of the vessel, is observed in case of the vertical orientation of the vessel. According to the weak temporal variability of the low wind speed (between 3 and 4.5 m/s) and direction parallel to the centre of the measuring area strong horizontal variations of the inhalation hazard occured in the range less than 50 m from the origin, while spatially homogeneous inhalation hazards were observed in the range of more than 50 m up to 200 m, almost independent on the orientation of the vessel. The extremely high total particle mass fractions between 1.6 and 8.6 mg at distances up to 50 m are noticeable. Scanning electron microscope analysis and electron probe microanalysis of Ce particles deposited up to distances of 100 m from the origin, indicated their deposition in the liquid state. (orig./HP)

Hydrocortisone selectively inhibits IgE-dependent arachidonic acid release from rat peritoneal mast cells

International Nuclear Information System (INIS)

Heiman, A.S.; Crews, F.T.

1984-01-01

Purified rat mst cells were used to study the effects of antiinflammatory steroids on the release of [1-14C]-arachidonic acid ([1-14C]AA) and metabolites. Mast cell were incubated overnight with glucocorticoids, [1-14C]AA incorporated into cellular phospholipids and the release of [1-14C]AA, and metabolites determined using a variety of secretagogues. Release of [1-14C]AA and metabolites by concanavalin A, the antigen ovalbumin and anti-immunoglobulin E antibody was markedly reduced by glucocorticoid treatment. Neither the total incorporation of [1-14C]AA nor the distribution into phospholipids was altered by hydrocortisone pretreatment. Glucocorticoid pretreatment did not alter [1-14C]AA release stimulated by somatostatin, compound 48/80, or the calcium ionophore, A23187. These data indicate that antiinflammatory steroids selectively inhibit immunoglobulin dependent release of arachidonic acid from rat mast cells. These findings question the role of lipomodulin and macrocortin as general phospholipase inhibitors and suggest that they may be restricted to immunoglobulin stimuli

Kinetics of extracellular release of 14C-labelled organic carbon by submerged macrophytes

International Nuclear Information System (INIS)

Soendergaard, M.

1981-01-01

The release of extracellular organic carbon (EOC) by six submerged freswater macrophytes was measured in time course studies with a 14 C-technique. Incubation in light in an open water-flow system made it possible to assay the time courses of 14 C-fixation and the simultaneous release of labelled EOC. Heterotrophic utilization of the released products by epiphytic communities was measured. Two patterns of release kinetics were found: (1) Constant rates of release occurred during the incubations, (2) The rates still increased after 24 h of incubation. During the first hours of incubation the rates of release increased in all species. Elodea reached constant rates after 2-4 h and Littorella and Ceratophyllum demersum after about 20 h. In the experiments with C. submersum and Nitella the rates of release increased almost linearly during the entire incubation period. The kinetics of release were in agreement with the molecular weight distribution of the dissolved EOC measured with gel chromatography. Low molecular weight products ( 10000 Daltons) dominated the dissolved EOC released by C. submersum and Nitella. A large fraction (18-60%) of the total EOC could be recovered on filters with a pore size of 0.2 μm. This particulate fraction probably represents some abiotic removal. The quantities of relase were low in all species and did not exceed 0.9% of the photosynthetic carbon fixation. Heterotrophic uptake by the epiphytic communities was less than 10% of the EOC released. The results emphasize that the 14 C-labelling of extracellular products is a time dependent process. (author)

Immobilization and controlled release of drug using plasma polymerized thin film

Energy Technology Data Exchange (ETDEWEB)

Myung, Sung-Woon [Department of Dental Materials, School of Dentistry, MRC Center, Chosun University, 309 Pilmun-daero, Dong-gu, Gwangju (Korea, Republic of); Jung, Sang-Chul [Department of Environmental Engineering, Sunchon National University, Sunchon 540-742 (Korea, Republic of); Kim, Byung-Hoon, E-mail: kim5055@chosun.ac.kr [Department of Dental Materials, School of Dentistry, MRC Center, Chosun University, 309 Pilmun-daero, Dong-gu, Gwangju (Korea, Republic of)

2015-06-01

In this study, plasma polymerization of acrylic acid was employed to immobilize drug and control its release. Doxorubicin (DOX) was immobilized covalently on the glass surface deposited with plasma polymerized acrylic acid (PPAAc) thin film containing the carboxylic group. At first, the PPAAc thin film was coated on a glass surface at a pressure of 1.33 Pa and radio frequency (RF) discharge power of 20 W for 10 min. DOX was immobilized on the PPAAc deposition in a two environment of phosphate buffer saline (PBS) and dimethyl sulfoxide (DMSO) solutions. The DOX immobilized surface was characterized by scanning electron microscope, atomic force microscope and attenuated total reflection Fourier transform infrared spectroscopy. The DOX molecules were more immobilized in PBS than DMSO solution. The different immobilization and release profiles of DOX result from the solubility of hydrophobic DOX in aqueous and organic solutions. Second, in order to control the release of the drug, PPAAc thin film was covered over DOX dispersed layer. Different thicknesses and cross-linked PPAAc thin films by adjusting deposition time and RF discharge power were covered on the DOX layer dispersed. PPAAc thin film coated DOX layer reduced the release rate of DOX. The thickness control of plasma deposition allows controlling the release rate of drug. - Highlights: • Doxorubicin was immobilized on the surface of plasma polymerized acrylic acid thin film. • Release profile of doxorubicin was affected by aqueous and organic solutions. • Plasma polymerized acrylic acid thin film can be used to achieve controlled release.

Immobilization and controlled release of drug using plasma polymerized thin film

International Nuclear Information System (INIS)

Myung, Sung-Woon; Jung, Sang-Chul; Kim, Byung-Hoon

2015-01-01

In this study, plasma polymerization of acrylic acid was employed to immobilize drug and control its release. Doxorubicin (DOX) was immobilized covalently on the glass surface deposited with plasma polymerized acrylic acid (PPAAc) thin film containing the carboxylic group. At first, the PPAAc thin film was coated on a glass surface at a pressure of 1.33 Pa and radio frequency (RF) discharge power of 20 W for 10 min. DOX was immobilized on the PPAAc deposition in a two environment of phosphate buffer saline (PBS) and dimethyl sulfoxide (DMSO) solutions. The DOX immobilized surface was characterized by scanning electron microscope, atomic force microscope and attenuated total reflection Fourier transform infrared spectroscopy. The DOX molecules were more immobilized in PBS than DMSO solution. The different immobilization and release profiles of DOX result from the solubility of hydrophobic DOX in aqueous and organic solutions. Second, in order to control the release of the drug, PPAAc thin film was covered over DOX dispersed layer. Different thicknesses and cross-linked PPAAc thin films by adjusting deposition time and RF discharge power were covered on the DOX layer dispersed. PPAAc thin film coated DOX layer reduced the release rate of DOX. The thickness control of plasma deposition allows controlling the release rate of drug. - Highlights: • Doxorubicin was immobilized on the surface of plasma polymerized acrylic acid thin film. • Release profile of doxorubicin was affected by aqueous and organic solutions. • Plasma polymerized acrylic acid thin film can be used to achieve controlled release

Peripheral blood corticotropin-releasing factor, adrenocorticotropic hormone and cytokine (Interleukin Beta, Interleukin 6, tumor necrosis factor alpha) levels after high- and low-dose total-body irradiation in humans

International Nuclear Information System (INIS)

Girinsky, T.A.; Pallardy, M.; Comoy, E.; Benassi, T.; Roger, R.; Ganem, G.; Socie, G.; Cossett, J.M.; Magdelenat, H.

1994-01-01

Total-body irradiation (TBI) induces an increase in levels of granulocytes and cortisol in blood. To explore the underlying mechanisms, we studied 26 patients who had TBI prior to bone marrow transplantation. Our findings suggest that only a high dose of TBI (10 Gy) was capable of activating the hypothalamopituitary area since corticotropin-releasing factor and blood adrenocorticotropic hormone levels increased at the end of the TBI. There was a concomitant increase in the levels of interleukin 6 and tumor necrosis factor in blood, suggesting that these cytokines might activate the hypothalamo-pituitary adrenal axis. Interleukin 1 was not detected. Since vascular injury is a common after radiation treatment, it is possible that interleukin 6 was secreted by endothelial cells. The exact mechanisms of the production of cyctokines induced by ionizing radiation remain to be determined. 25 refs., 1 fig

Effect of total lymphoid irradiation on pancreatic islet xenograft survival in rats

International Nuclear Information System (INIS)

Nakajima, Y.; Lie, T.S.; Nakauo, H.; Nakagawa, K.; Segawa, M.

1984-01-01

Before transplantation of Syrian hamster pancreatic islet xenografts to diabetic rats the recipients received total lymphatic system irradiation and cyclosporin A treatment after transplantation for immunosuppression. The xenograft survival times were measured and the rat anti-hamster lymphocytotoxic titers were determined by 51 Cr release assay

Effect of total lymphoid irradiation on pancreatic islet xenograft survival in rats

Energy Technology Data Exchange (ETDEWEB)

Nakajima, Y; Lie, T S [Bonn Univ. (Germany, F.R.). Chirurgische Klinik und Poliklinik; Nakauo, H; Nakagawa, K; Segawa, M [Nara Women' s Univ. (Japan). Dept. of Physics

1984-01-01

Before transplantation of Syrian hamster pancreatic islet xenografts to diabetic rats the recipients received total lymphatic system irradiation and cyclosporin A treatment after transplantation for immunosuppression. The xenograft survival times were measured and the rat anti-hamster lymphocytotoxic titers were determined by /sup 51/Cr release assay.

Population dose commitments due to radioactive releases from nuclear-power-plant sites in 1978

International Nuclear Information System (INIS)

Peloquin, R.A.; Schwab, J.D.; Baker, D.A.

1982-06-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1978. Fifty-year dose commitments from a one-year exposure were calculated from both liquid and atmospheric releases for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each site. This report tabulates the results of these calculations, showing the dose commitments for both liquid and airborne pathways for each age group and organ. Also included for each site is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total dose commitment from both liquid and airborne pathways ranged from a high of 200 person-rem to a low of 0.0004 person-rem with an arithmetic mean of 14 person-rem. The total population dose for allsites was estimated at 660 person-rem for the 93 million people considered at risk. The average individual dose commitment from all pathways on a site basis ranged from a low of 3 x 10 -6 mrem to a high of 0.08 mrem. No attempt was made in this study to determine the maximum dose commitment received by any one individual from the radionuclides released at any of the sites

Population dose commitments due to radioactive releases from Nuclear-Power-Plant Sites in 1979

International Nuclear Information System (INIS)

Baker, D.A.; Peloquin, R.A.

1982-12-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1979. Fifty-year dose commitments from a one-year exposure were calculated from both liquid and atmospheric releases for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each site. This report tabulates the results of these calculations, showing the dose commitments for both liquid and airborne pathways for each age group and organ. Also included for each site is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total dose commitment from both liquid and airborne pathways ranged from a high of 1300 person-rem to a low of 0.0002 person-rem with an arithmetic mean of 38 person-rem. The total population dose for all sites was estimated at 1800 person-rem for the 94 million people considered at risk. The average individual dose commitment from all pathways on a site basis ranged from a low of 2 x 10 - 6 mrem to a high of 0.7 mrem. No attempt was made in this study to determine the maximum dose commitment received by any one individual from the radionuclides released at any of the sites

Environmental contamination from a ground-level release of fission products

International Nuclear Information System (INIS)

Stupka, R.C.; Kephart, G.S.; Rittmann, P.D.

1986-08-01

On January 11, 1985, a ground-level release of fission products, primarily 90 Sr, occurred at the Hanford Site in southeastern Washington State. The release was detected during routine surveys and the majority of the contamination was confined to the immediate area where the release occurred. Response to the incident was complicated by a strong inversion that resulted in a buildup of 222 Rn daughter products on environmental air samples and outdoor surfaces. The cause of the release appears to have been the operation of a transfer jet that inadvertently pressurized an unblanked line leading to the 241-C-151 Diversion Box. A buildup of pressure inside the diversion box forced contaminated air through gaps in the diversion box cover blocks resulting in an unmonitored, short duration release to the environment. The source term was estimated using data obtained from environmental air samplers. The ground deposition speed was calculated using the integrated exposure (air samples) and surface contamination levels obtained from recently fallen snow. The total release was estimated to be 1.4 Ci 90 Sr and 0.02 Ci 137 Cs. Based on this source term, the maximum 50-yr dose commitment to onsite pesonnel was 50 mrem whole body and 600 mrem bone. No detectable internal deposition occurred during the incident and corrective action which followed; this was probably due to several factors: (1) prompt detection of the release; (2) localized contamination control; (3) excellent personnel protection practices; and (4) the protection offered by building ventilation systems. The theoretical maximum offsite individual would receive a potential 1-yr dose commitment of 0.01 mrem whole body and 0.2 mrem bone from this incident. The potential 50-yr dose commitment would be 0.13 mrem whole body and 2.0 mrem bone. In actuality, neither onsite or offsite individuals would be expected to receive even these small dose commitments

Total gamma activity measurements for determining the radioactivity of residual materials from nuclear power stations

International Nuclear Information System (INIS)

Auler, I.; Meyer, M.; Stickelmann, J.

1995-01-01

Large amounts of residual materials from retrofitting measures and from decommissioning of nuclear power stations shows such a weak level of radioactivity that they could be released after decision measurements. Expenses incurred with complex geometry cannot be taken with common methods. NIS developed a Release Measurement Facility (RMF) based on total gamma activity measurements especially for these kind of residual materials. The RMF has been applied for decision measurements in different nuclear power plants. Altogether about 2,000 Mg of various types of materials have been measured up to now. More than 90 % of these materials could be released 0 without any restriction after decision measurements

Analysis of railroad tank car releases using a generalized binomial model.

Science.gov (United States)

Liu, Xiang; Hong, Yili

2015-11-01

The United States is experiencing an unprecedented boom in shale oil production, leading to a dramatic growth in petroleum crude oil traffic by rail. In 2014, U.S. railroads carried over 500,000 tank carloads of petroleum crude oil, up from 9500 in 2008 (a 5300% increase). In light of continual growth in crude oil by rail, there is an urgent national need to manage this emerging risk. This need has been underscored in the wake of several recent crude oil release incidents. In contrast to highway transport, which usually involves a tank trailer, a crude oil train can carry a large number of tank cars, having the potential for a large, multiple-tank-car release incident. Previous studies exclusively assumed that railroad tank car releases in the same train accident are mutually independent, thereby estimating the number of tank cars releasing given the total number of tank cars derailed based on a binomial model. This paper specifically accounts for dependent tank car releases within a train accident. We estimate the number of tank cars releasing given the number of tank cars derailed based on a generalized binomial model. The generalized binomial model provides a significantly better description for the empirical tank car accident data through our numerical case study. This research aims to provide a new methodology and new insights regarding the further development of risk management strategies for improving railroad crude oil transportation safety. Copyright © 2015 Elsevier Ltd. All rights reserved.

Determination of the long-term release of metal(loid)s from construction materials using DGTs.

Science.gov (United States)

Schmukat, A; Duester, L; Ecker, D; Heininger, P; Ternes, T A

2013-09-15

Long-term leaching experiments are crucial to estimate the potential release of dangerous substances from construction materials. The application of Diffuse Gradients in Thin film (DGT) in static-batch experiments was tested to study the long-term release of metal(loid)s from construction materials for hydraulic engineering, for half a year. Long-term release experiments are essential to improve calculations of the life-time release for this materials. DGTs in batch experiments were found to be a space and labour efficient application, which enabled (i) to study, in a non-invasive manner, the total release of nine metal(loid)s for half a year, (ii) to differentiate between release mechanisms and (iii) to study mechanisms which were contrary to the release or caused experimental artefacts in the batch experiments. For copper slag (test material) it was found that eight metal(loid)s were released over the whole time period of 184 d. Cu, Ni and Pb were found to be released, predominantly caused by (the) weathering of sulphide minerals. Only for Zn a surface depletion mechanism was identified. The results from the long-term batch experiments deliver new information on the release of metal(loid)s during the life cycle of construction materials with regard to river basin management objectives. Copyright © 2013 Elsevier B.V. All rights reserved.

VizieR Online Data Catalog: VIKING catalogue data release 2 (Edge+, 2016)

Science.gov (United States)

Edge, A.; Sutherland, W.; Viking Team

2016-10-01

The VIKING survey with VISTA (ESO programme ID 179.A-2004) is a wide area (eventually 1500 sq.degrees), intermediate-depth (5-sigma detection limit J=21 on Vega system) near-infrared imaging survey, in the five broadband filters Z, Y, J, H, Ks. The planned sky coverage is at high galactic latitudes, and includes two main stripes 70x10°2 each: one in the South Galactic cap near Dec~-30°, and one near Dec~0° in the North galactic cap; in addition, there are two smaller outrigger patches called GAMA09 and CFHLS-W1. Science goals include z>6.5 quasars, extreme brown dwarfs, and multiwavelength coverage and identifications for a range of other imaging surveys, notably VST-KIDS and Herschel-ATLAS. This second public data release of VIKING data covers all of the highest quality data taken between the start of the survey (12th of November 2009) and the end of Period 92 (30th September 2013). This release supersedes the first release (VIKING and VIKING CAT published 28.06.2013 and 16.12.2013 respectively) as it includes improved CASU processing (V1.3) that gives better tile grouting and zero point corrections This release contains 396 tiles with coverage in all five VIKING filters, 379 of which have a deep co-add in J, and an additional 81 with at least two filters where the second OB has not been executed yet or one filter in an OB was poor quality. These 477 fields cover a total of ~690 square degrees and the resulting catalogues include a total of 46,270,162 sources (including low-reliability single-band detections). The imaging and catalogues (both single-band and band-merged) total 839.3GB. The coverage in each of the five sub-areas is not completely contiguous but any inter-tile gaps are relatively small. More details can be found in the accompanying documentation: vikingcatdr2.pdf (2 data files).

Sustained release nimesulide microparticles: evaluation of release modifying property of ethy

International Nuclear Information System (INIS)

Khan, S.A.; Ahmed, M.; Nisar-ur-Rehman; Madni, A.U.; Aamir, M.N.; Murtaza, G.

2011-01-01

Microencapsulated controlled-release preparations of nimesulide were formulated. Microparticles were prepared by modified phase separation (non-solvent addition) technique using different ratios of ethylcellulose. The microparticles (M/sub 1/, M/sub 2/, and M/sub 3/) were yellow, free flowing and spherical in shape with the particle size varying from 93.62 +- 14.15 to 104.19 +- 18.15 mu m. The t/sub 60%/of nimesulide release from microparticles was found to be 3 +- 0.6, 5 +- 0.6 and 8 +- 0.8 h for formulations M/sub 1/, M/sub 2/, and M/sub 3/, respectively. FT-IR, XRD, and thermal analysis were done which showed that there is no interaction between the polymer and drug. The mechanism of drug release from nimesulide microparticles was studied by using Higuchi and Korsmeyer-Peppas models. The value of coefficient of determination (R/sup 2/) for M/sub 1/, M/sub 2/, and M/sub 3/ indicates anomalous and case-II transport release mechanism. The dissolution data of designed system verified its ability to maintain plasma concentration without the need of frequent dosing. The Nimesulide microparticles prolonged drug release for 12 hours or longer. Based on the results of release studies, M/sub 3/ was opted as a suitable microparticulate formulation allowing the controlled release of nimesulide over a prolonged period of time. Moreover, its encapsulation efficiency was also comparable to the other two formulations (M/sub 1/ and M/sub 2/). In conclusion, the influence of polymer concentration should be considered during formulation development. (author)

Multiplate ionization total absorption spectrometer with a compressed gas

International Nuclear Information System (INIS)

Baskakov, V.I.; Dolgoshein, B.A.; Kantserov, V.A.

1978-01-01

The characteristics of a multiplate total absorption spectrometer working with the compressed xenon (up to 25 atm) containing up to 23 radiation lengths of matter are studied. The dependence of the spectrometer energy resolution on the detecting matter density, on the material and thickness of the absorber plates has been studied. The ability of the spectrometer with a tungsten absorber to select hadrons and electrons with P=6 GeV/c by total energy release and characteristics of the cascade longitudinal development has been also studied. The gas spectrometer as it is shown differs quite slightly from the similar spectrometer with liquid argon as for its time resolution it is much better

Alginate/cellulose beads as supports for slow release of nutrient

Energy Technology Data Exchange (ETDEWEB)

Matos, Mailson de; Mattos, Bruno Dufau, E-mail: mailsondematos@gmail.com [Universidade Federal do Parana (UFPR), Curitiba, PR (Brazil); Magalhaes, Washington [Empresa Brasileira de Pesquisa Agropecuaria (EMBRAPA), Londrina, PR (Brazil)

2016-07-01

Full text: A total of 9 billion inhabitants is estimated by 2050, which will put a heavy pressure towards an increased cereal yield of at least 40% [1]. The smart systems for nutrient delivery could be used to increase the cropland productivity and biodegradable supports are especially needed to decrease the bio-accumulation of the synthetic materials. Thus, alginate and cellulose were chosen to encapsulate nitrogen and further release it. Briefly, the encapsulated systems were synthesized as follow: solutions containing ammonium nitrate, sodium alginate, cellulose nanofibrils and nano-silica were prepared. Each mixture was dropwise added into the calcium chloride (50 wt%) crosslinking agent solution. After the bead-forming reaction, the obtained material was filtered and dried at 60 deg C. The characterizations were performed by using X-ray diffraction (XRD), energy dispersive X-ray spectroscopy coupled to scanning electron microscopy (SEMEDS), Fourier-transformed infrared spectroscopy (FT-IR) and release tests according to DIN EN 13266:2002. In general, the nano-silica was important for better handling the obtained beads; however, it changed the bead morphology and tended to increase the release rate of nitrogen. The best formulations were obtained with the presence of cellulose nanofibrils and few amounts of silica in the beads. At these compositions the systems follow the criteria of slow-release purposes, i.e., 15% released after 24h and less than 75% after 28 days. References: [1] Maxmen A, Nature vol. 501 (2013). (author)

3D printing of tablets containing multiple drugs with defined release profiles.

Science.gov (United States)

Khaled, Shaban A; Burley, Jonathan C; Alexander, Morgan R; Yang, Jing; Roberts, Clive J

2015-10-30

We have employed three-dimensional (3D) extrusion-based printing as a medicine manufacturing technique for the production of multi-active tablets with well-defined and separate controlled release profiles for three different drugs. This 'polypill' made by a 3D additive manufacture technique demonstrates that complex medication regimes can be combined in a single tablet and that it is viable to formulate and 'dial up' this single tablet for the particular needs of an individual. The tablets used to illustrate this concept incorporate an osmotic pump with the drug captopril and sustained release compartments with the drugs nifedipine and glipizide. This combination of medicines could potentially be used to treat diabetics suffering from hypertension. The room temperature extrusion process used to print the formulations used excipients commonly employed in the pharmaceutical industry. Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR-FTIR) and X-ray powder diffraction (XRPD) were used to assess drug-excipient interaction. The printed formulations were evaluated for drug release using USP dissolution testing. We found that the captopril portion showed the intended zero order drug release of an osmotic pump and noted that the nifedipine and glipizide portions showed either first order release or Korsmeyer-Peppas release kinetics dependent upon the active/excipient ratio used. Copyright © 2015. Published by Elsevier B.V.

Investigating the in vitro drug release kinetics from controlled release diclofenac potassium-ethocel matrix tablets and the influence of co-excipients on drug release patterns.

Science.gov (United States)

Shah, Shefaat Ullah; Shah, Kifayat Ullah; Rehman, Asimur; Khan, Gul Majid

2011-04-01

The objective of the study was to formulate and evaluate controlled release polymeric tablets of Diclofenac Potassium for the release rate, release patterns and the mechanism involved in the release process of the drug. Formulations with different types and grades of Ethyl Cellulose Ether derivatives in several drug-to-polymer ratios (D:P) were compressed into tablets using the direct compression method. In vitro drug release studies were performed in phosphate buffer (pH 7.4) as dissolution medium by using USP Method-1 (Rotating Basket Method). Similarity factor f2 and dissimilarity factor f1 were applied for checking the similarities and dissimilarities of the release profiles of different formulations. For the determination of the release mechanism and drug release kinetics various mathematical/kinetic models were employed. It was found that all of the Ethocel polymers could significantly slow down the drug release rate with Ethocel FP polymers being the most efficient, especially at D:P ratios of 10:03 which lead towards the achievement of zero or near zero order release kinetics.

Protecting privacy in data release

CERN Document Server

Livraga, Giovanni

2015-01-01

This book presents a comprehensive approach to protecting sensitive information when large data collections are released by their owners. It addresses three key requirements of data privacy: the protection of data explicitly released, the protection of information not explicitly released but potentially vulnerable due to a release of other data, and the enforcement of owner-defined access restrictions to the released data. It is also the first book with a complete examination of how to enforce dynamic read and write access authorizations on released data, applicable to the emerging data outsou

Environmental releases for calendar year 1997

International Nuclear Information System (INIS)

Gleckler, B.P.

1998-01-01

This report fulfills the annual environmental release reporting requirements of US Department of Energy (DOE) Order 5400.1. This report provides supplemental information to the Hanford Site Environmental Report (PNNL-11795). The Hanford Site Environmental Report provides an update on the environmental status of the Hanford Site. The sitewide annual report summarizes the degree of compliance with applicable environmental regulations and informs the public concerning the impact of Hanford Site operations on the surrounding environment. Like the Hanford Site Environmental Report, this annual report presents a summary of the environmental releases from facilities and activities managed by the Fluor Daniel Hanford, Incorporated (FDH), and Bechtel Hanford, Incorporated (BHI). In addition to the summary data, this report also includes detailed data on air emissions, liquid effluents, and hazardous substances released to the environment during calendar year 1997. Comprehensive data summaries of air emissions and liquid effluents in 1997 are displayed in Tables ES-1 through ES-5. These tables represent the following: Table ES-1--Radionuclide air emissions data (detailed data on emissions are presented in Section 2.0); Table ES-2--Data on radioactive liquid effluents discharged to the soil (detailed data are presented in Section 3.0); Table ES-3--Radionuclides discharged to the Columbia River (detailed data are presented in Section 3.0); Table ES-4--Nonradioactive air emissions data (detailed data are presented in Section 2.0); Table ES-5--Total Volumes and Flow Rates of 200/600 Area Radioactive Liquid Effluents (detailed data are presented in Section 3.0)

EPICS release 3.11 specific documentation -- EPICS release notes for 3.11

International Nuclear Information System (INIS)

1994-01-01

EPICS release 3.11 is now ready for user testing. A person who wants to set up a simplified application environment to boot an IOC and create databases using R3.11 should follow the directions in Appendix B, page 27, of the EPICS Source/Release Control Manual, Sept. 20, 1993. The R3.11 EPICS path at ANL/APS is /net/phebos/epics/R3.11 so the command to get the new release is /net/phebos/epics/R3.11/Unix/share/bin/getrel /net/phebos/epics/R3.11. An existing R3.8 short form report can be copied to this new directory and used to create a database. ANL/APS is currently testing an Application Developers Source/Release control system. It is not yet ready for general distribution. Attached are the EPICS R3.11 release notes

Fission product release profiles from spherical HTR fuel elements at accident temperatures

International Nuclear Information System (INIS)

Schenk, W.; Pitzer, D.; Nabielek, H.

1986-10-01

A total of 22 fuel elements with modern TRISO particles has been tested in the temperature range 1500-2500 0 C. Additionally, release profiles of iodine and other isotopes have been obtained with seven UO 2 samples at 1400-1800 0 C. For heating times up to 100 hours at the maximum temperature, the following results are pertinent to HTR accident conditions: Ag 110 m is the only fission products to be released at 1200-1600 0 C by diffusion through intact SiC, but it is of low significance in accident assessments; cesium, iodine, strontium, and noble gas releases up to 1600 0 C are solely due to various forms of contamination; at 1700-1800 0 C, corrosion induced SiC defects cause the release of Cs, Sr, I/Xe/Kr; above 2000 0 C, thermal decomposition of the silicon carbide layer sets in while pyrocarbons still remain intact. Around 1600 0 C, the accident specific contribution of cesium, strontium, iodine, and noble gases is negligible. (orig./HP) [de

Research on release rate of volatile organic compounds in typical vessel cabin

Directory of Open Access Journals (Sweden)

ZHANG Jinlan

2018-02-01

Full Text Available [Objectives] Volatile Organic Compounds (VOC should be efficiently controlled in vessel cabins to ensure the crew's health and navigation safety. As an important parameter, research on release rate of VOCs in cabins is required. [Methods] This paper develops a method to investigate this parameter of a ship's cabin based on methods used in other closed indoor environments. A typical vessel cabin is sampled with Tenax TA tubes and analyzed by Automated Thermal Desorption-Gas Chromatography-Mass Spectrometry (ATD-GC/MS. The lumped mode is used and the release rate of Benzene, Toluene, Ethylbenzene and Xylene (BTEX, the typical representatives of VOCs, is obtained both in closed and ventilated conditions. [Results] The results show that the content of xylene and Total Volatile Organic Compounds (TVOC exceed the indoor environment standards in ventilated conditions. The BTEX release rate is similar in both conditions except for the benzene. [Conclusions] This research builds a method to measure the release rate of VOCs, providing references for pollution character evaluation and ventilation and purification system design.

Naloxone inhibits superoxide but not enzyme release by human neutrophils

Energy Technology Data Exchange (ETDEWEB)

Simpkins, C.; Alailima, S.; Tate, E.

1986-03-01

The release of toxic oxygen metabolites and enzymes by phagocytic cells is thought to play a role in the multisystemic tissue injury of sepsis. Naloxone protects septic animals. We have found that at concentrations administered to animals (10/sup -7/ to 10/sup -4/M), naloxone inhibited (p < .001) the release of superoxide (O/sub 2//sup -/) by human neutrophils (HN), stimulated with N-formyl methionyl leucyl phenylalanine (FMLP). Naloxone had no effect on cell viability. Maximum inhibition was 65% of the total O/sub 2//sup -/ released (13.1 nMoles/8 min/320,000 cells). FMLP-stimulated release of beta-glucoronidase or lysozyme was not altered by naloxone. Naloxone had no effect on the binding of /sup 3/H FMLP to HN. Using /sup 3/H naloxone and various concentrations of unlabeled naloxone higher affinity (K/sub D/ = 12nM) and lower affinity (K/sub D/ = 4.7 x 10/sup -5/) binding sites were detected. The K/sub D/ of the low affinity site corresponded to the ED/sub 50/ for naloxone inhibition of O/sub 2//sup -/ (1 x 10/sup -5/M). Binding to this low affinity site was decreased by (+) naloxone, beta-endorphin and N acetyl beta-endorphin, but not by leu-enkephalin, thyrotropin releasing factor, prostaglandin D/sub 2/ or E/sub 2/. Conclusions: (1) naloxone inhibits FMLP-stimulated O/sub 2/ but not enzyme release, (2) this inhibition is not due to alteration of FMLP receptor binding, (3) naloxone may act via a low affinity binding site which is ligand specific, and (4) a higher affinity receptor is present on HN.

Effect of the timing of tourniquet release on postoperative hematoma formation: an experimental animal study

Energy Technology Data Exchange (ETDEWEB)

Himel, H.N.; Ahmad, M.; Parmett, S.R.; Strauss, H.W.; May, J.W. Jr.

1989-04-01

There is a controversy over when to release a pneumatic tourniquet after completing a hand surgical procedure. To study this controversy, we performed a standardized operation with tourniquet inflow occlusion on both lower legs of a series of rabbits. Total tourniquet time and the procedure performed, including intraoperative Bovie electrocautery of actual and potential bleeding points identified with 2.5 X loupe magnification, were identical on the two sides, except for the method of tourniquet release. On one leg, the tourniquet was released and all new bleeding points were controlled prior to wound closure. On the other leg, the tourniquet was released after the wound had been closed and dressed. Animals were injected with technetium-99m-labeled red blood cells and scanned to measure hematoma formation. Qualitatively, we observed more label in the leg whose tourniquet was released after wound closure in 17 of the 20 animals (p less than 0.005). Quantitatively, we also measured more mean label in the leg whose tourniquet was released after the wound was closed (p less than 0.001). Tourniquet release after wound closure was associated with greater hematoma formation.

Effect of the timing of tourniquet release on postoperative hematoma formation: an experimental animal study

International Nuclear Information System (INIS)

Himel, H.N.; Ahmad, M.; Parmett, S.R.; Strauss, H.W.; May, J.W. Jr.

1989-01-01

There is a controversy over when to release a pneumatic tourniquet after completing a hand surgical procedure. To study this controversy, we performed a standardized operation with tourniquet inflow occlusion on both lower legs of a series of rabbits. Total tourniquet time and the procedure performed, including intraoperative Bovie electrocautery of actual and potential bleeding points identified with 2.5 X loupe magnification, were identical on the two sides, except for the method of tourniquet release. On one leg, the tourniquet was released and all new bleeding points were controlled prior to wound closure. On the other leg, the tourniquet was released after the wound had been closed and dressed. Animals were injected with technetium-99m-labeled red blood cells and scanned to measure hematoma formation. Qualitatively, we observed more label in the leg whose tourniquet was released after wound closure in 17 of the 20 animals (p less than 0.005). Quantitatively, we also measured more mean label in the leg whose tourniquet was released after the wound was closed (p less than 0.001). Tourniquet release after wound closure was associated with greater hematoma formation

Massive radioactive releases have a great impact on the accident costs

International Nuclear Information System (INIS)

Pascucci-Cahen, L.; Momal, P.

2013-01-01

This article investigates the costs of the consequences of a nuclear accident. The importance of the costs is very dependant on the amount of radioactivity released in the environment during the accident. 2 severe accidents are considered, each accident involves the fusion of the core but the first is characterized by a limited amount of radioactivity released in the atmosphere while the second involves massive radioactive releases. The list of consequences is as comprehensive as possible: site decontamination and dismantlement, land decontamination, sanitary impacts, population displacement, agricultural and economical losses, impact on tourism, impact on the production of electricity...In the first case the total cost reaches 120 billion euros which is still manageable at the scale of a country whereas in the second case the bill reaches 430 billion euros which is unbearable for a country. The very slight probability of such events does not compensate for their catastrophic potentials. (A.C.)

Effectiveness of cleanup criteria relative to an accidental nuclear release

International Nuclear Information System (INIS)

Chen, S.Y.; Yuan, Y.C.

1988-01-01

In the event of an accidental nuclear release, the associated long-term radiological risks would result primarily from ground contamination pathways. Cleanup of the contaminated ground surfaces is a necessary step toward reducing the radiological risk to the general population. Ideally, the radiological risk decreases as the level of cleanup effort increases; however, as the cleanup criterion (i.e., the required contaminant concentration after cleanup) becomes more stringent, the cleanup effort may become prohibitively costly. This study examines several factors that are important in determining the effectiveness of the cleanup criteria for selected radionuclides: (a) annual individual dose commitment (mrem/yr), (b) total population environmental dose commitment (person-rem), and (c) total area (km 2 ) requiring cleanup following an accident. To effectively protect the general population, the benefits of cleanup should be weighed against the potentially large increase in cleanup area (and the associated costs) as the cleanup criterion becomes more stringent. The effectiveness of cleanup will vary, depending largely on site-specific parameters such as population density and agricultural productivity as well as on the amount and type of radionuclide released. Determination of an optimum cleanup criterion should account for all factors, including a comprehensive cost/benefit analysis

Environmental releases for calendar year 1993

International Nuclear Information System (INIS)

Thomas, S.P.; Curn, B.L.

1994-07-01

This report presents data on radioactive and nonradioactive materials released into the environment during calendar year 1993 from facilities managed by Westinghouse Hanford Company. As part of this executive summary, comprehensive data summaries of air emissions and liquid effluents in 1993 are displayed in tables. These tables represent the following: radionuclide air emissions data; data on radioactive liquid effluents discharged to the soil; radionuclides discharged to the Columbia River; nonradioactive air emissions data; total volumes and flow rates of 200/600 area liquid effluents. Both summary and detailed presentations of these data are given. When appropriate, comparisons to data from previous years are made

Triggered Release from Polymer Capsules

Energy Technology Data Exchange (ETDEWEB)

Esser-Kahn, Aaron P. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry; Odom, Susan A. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry; Sottos, Nancy R. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Materials Science and Engineering; White, Scott R. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Aerospace Engineering; Moore, Jeffrey S. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry

2011-07-06

Stimuli-responsive capsules are of interest in drug delivery, fragrance release, food preservation, and self-healing materials. Many methods are used to trigger the release of encapsulated contents. Here we highlight mechanisms for the controlled release of encapsulated cargo that utilize chemical reactions occurring in solid polymeric shell walls. Triggering mechanisms responsible for covalent bond cleavage that result in the release of capsule contents include chemical, biological, light, thermal, magnetic, and electrical stimuli. We present methods for encapsulation and release, triggering methods, and mechanisms and conclude with our opinions on interesting obstacles for chemically induced activation with relevance for controlled release.

Calcitonin gene-related peptide and somatostatin releases correlated with the area under the lafutidine concentration-time curve in human plasma.

Science.gov (United States)

Ikawa, K; Shimatani, T; Azuma, Y; Inoue, M; Morikawa, N

2006-08-01

To examine the effects of the histamine H(2)-receptor antagonist, lafutidine, at clinical dosage (10 mg tablet after a standardized meal) on plasma levels of the gastrointestinal peptides, calcitonin gene-related peptide (CGRP), somatostatin and gastrin. Six healthy male volunteers ate a standardized meal, and received either lafutidine orally at a dose of 10 mg or water only (control). Blood samples were taken before and up to 4 h after the drug administration. Plasma lafutidine concentrations were determined by high pressure liquid chromatography. Pharmacokinetic analysis of lafutidine was performed using one-compartmental model. The levels of immunoreactive substances of plasma CGRP, somatostatin and gastrin were measured by enzyme immunoassay, and the amount of peptide release was calculated by the trapezoidal method. Lafutidine significantly increased plasma CGRP levels at 1, 1.5, 2.5 and 4 h and the total amount of CGRP release (192 +/- 14.0 pg.h/mL) compared with the control group (128 +/- 21.5 pg.h/mL). Lafutidine significantly increased the plasma somatostatin levels at 1 and 1.5 h, and the total amount of somatostatin released (107 +/- 18.2 pg.h/mL) compared with the control (78.4 +/- 7.70 pg.h/mL). The area under the drug concentration-time curve (AUC) from 0 to 4 h after administration correlated well with the Delta-CGRP and Delta-somatostatin release but not with total amount of gastrin released. However, plasma gastrin levels were significantly elevated at 1.5 h after drug administration. Lafutidine at clinical dosage increases plasma CGRP and the somatostatin. The amounts released correlated with the AUC of lafutidine in humans. These results suggest that the increased release of CGRP and somatostatin may contribute to its gastroprotective and anti-acid secretory effect.

Guidance for Evaluating the Safety of Experimental Releases of Mosquitoes, Emphasizing Mark-Release-Recapture Techniques.

Science.gov (United States)

Benedict, Mark Q; Charlwood, J Derek; Harrington, Laura C; Lounibos, L Philip; Reisen, William K; Tabachnick, Walter J

2018-01-01

Experimental releases of mosquitoes are performed to understand characteristics of populations related to the biology, ability to transmit pathogens, and ultimately their control. In this article, we discuss considerations related to the safety of experimental releases of living mosquitoes, applying principles of good practice in vector biology that protect human health and comfort. We describe specific factors of experimental releases of mosquitoes that we believe are critical to inform institutional biosafety committees and similar review boards to which proposals to conduct mosquito release experiments have been submitted. In this study, "experimental releases" means those that do not significantly increase vector capacity or nuisance biting relative to the unperturbed natural baseline. This document specifically does not address releases of mosquitoes for ongoing control programs or trials of new control methods for which broader assessments of risk are required. It also does not address releases of transgenic or exotic (non-native) mosquito species, both of which require particular regulatory approval. Experimental releases may include females and males and evaluation must consider their effects based on the number released, their genotype and phenotype, the environment into which they are released, and postrelease collection activities. We consider whether increases of disease transmission and nuisance biting might result from proposed experimental releases against the backdrop of natural population size variation. We recommend that experimental releases be conducted in a manner that can be reasonably argued to have insignificant negative effects. Reviewers of proposals for experimental releases should expect applicants to provide such an argument based on evidence from similar studies and their planned activities. This document provides guidance for creating and evaluating such proposals.

Investigation of activity release from bituminized intermediate-level waste forms under thermal stresses

International Nuclear Information System (INIS)

Kluger, W.; Vejmelka, P.; Koester, R.

1983-01-01

To determine the consequences of a fire during fabrication, intermediate storage and transport of bituminized NaNO 3 waste forms, the fractions of plutonium released from the waste forms were assessed. For this purpose, laboratory tests were made with PuO 2 -containing specimens as well as a field test with specimens containing Eu 2 O 3 . By the evaluation of plutonium release in the laboratory and by the determination of the total sodium release and the relative Eu/Na release in the field tests the plutonium release can be deduced from full-scale specimens. The results show that for bituminized waste forms with high NaNO 3 contents (approx. 36 wt%) the average plutonium release obtained in laboratory testing is 15%. In the field tests (IAEA fire test conditions) an average Eu release of 8% was found. These results justify the statement that also for waste forms in open 175 L drum inserts a maximum plutonium release of about 15% can be expected. From the time-dependence of Eu/Na release in the field tests an induction period of 15-20 minutes between the start of testing and the first Na/Eu release can be derived. The maximum differential Na/Eu release occurs after a test period of 45 to 60 minutes duration and after 90 to 105 minutes (tests K2 and K4, respectively); after that time also the highest temperatures in the products are measured. The release values were determined for products in open 175 L drum inserts which in this form are not eligible for intermediate and ultimate storage. For bituminized waste forms in concrete packages (lost concrete shieldings) a delayed increase in temperature to only 70-80 deg. C takes place (4-5 hours after extinction of the fire) if the fire lasts 45 minutes. The concrete package remains intact under test conditions. This means that activity release from bituminized waste forms packaged in this way can be ruled out in the case under consideration. (author)

Therapeutic effects of 5-fluorouracil sustained-release particles in 81 malignant pericardial effusion patients

Directory of Open Access Journals (Sweden)

Yong-Li Ji

2015-02-01

Full Text Available This study aimed to investigate the clinical application value of the 5-fluorouracil (5-FU sustained-release particles implanted along the cardiac tangent direction into malignant pericardial effusion (MPCE. A total of 81 MPCE patients underwent pericardiocentesis, and were implanted with 5-FU sustained-release particles into the pericardial cavity under ultrasound guidance. The puncturing path was along the cardiac tangent direction. Ultrasound examinations were performed every week, and the efficacy was evaluated 4 weeks after treatment. The 45 patients who were treated with pericardial catheter drainage and simultaneous intracavitary chemotherapy were used as the control group. The success rate of pericardiocentesis was 100%. Ultrasound reviews performed 4 weeks after treatment showed that 71 cases achieved complete remission and eight cases achieved partial remission, while treatment was completely ineffective in two cases. The total remission rate was 97.53%, which was significantly higher than that of the control group (77.78%, p < 0.01. The implantation of 5-FU sustained-release particles along the cardiac tangent direction was safe, and demonstrated good efficacy and fewer adverse reactions. Thus, this method could be ideal for the treatment of MPCE.

Nickel and cobalt release from jewellery and metal clothing items in Korea.

Science.gov (United States)

Cheong, Seung Hyun; Choi, You Won; Choi, Hae Young; Byun, Ji Yeon

2014-01-01

In Korea, the prevalence of nickel allergy has shown a sharply increasing trend. Cobalt contact allergy is often associated with concomitant reactions to nickel, and is more common in Korea than in western countries. The aim of the present study was to investigate the prevalence of items that release nickel and cobalt on the Korean market. A total of 471 items that included 193 branded jewellery, 202 non-branded jewellery and 76 metal clothing items were sampled and studied with a dimethylglyoxime (DMG) test and a cobalt spot test to detect nickel and cobalt release, respectively. Nickel release was detected in 47.8% of the tested items. The positive rates in the DMG test were 12.4% for the branded jewellery, 70.8% for the non-branded jewellery, and 76.3% for the metal clothing items. Cobalt release was found in 6.2% of items. Among the types of jewellery, belts and hair pins showed higher positive rates in both the DMG test and the cobalt spot test. Our study shows that the prevalence of items that release nickel or cobalt among jewellery and metal clothing items is high in Korea. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Evaluation of the release behavior of the dexamethasone embedded in polycarbonate polyurethane membranes: an in vitro study

International Nuclear Information System (INIS)

Kim, Dong Hyun; Kang, Sung Gwon; Lee, Chul Gab; Park, Sang Soo; Lee, Don Haeng; Lee, Gyu Baek; Song, Ho Young

2003-01-01

To evaluate the release behavior of dexamethasone embedded in a polycarbonate polyurethane membrane. Both water-soluble and water-insoluble dexamethasone were tested, and the release behavior of five water-insoluble dexamethasone films of different thickness (78 to 211 μm) was also evaluated. The amount of dexamethasone used was 10% of the total weight of the polyurethan film mass. Each film was placed in a centrifuge tube containing 25 ml of 0.1-M neutral phosphate buffer, and the tubes were placed in a shaking incubator to quantify the amount of drug released into the buffer, absorption spectroscopy (λ max=242 nm) was employed. In the test involving water-soluble dexamethasone, 60%, of the drug was released during the first two hours of the study. Films containing water-insoluble dexamethasone, on the other hand, released 40%, 60% and 75% of the dexamethasone in one, three and seven days, respectively. Both types of film maintained low-dose drug release for 28 days. When release behavior was compared between water-insoluble films of different thickness, thicker film showed less initial burst and more sustained release. Dexamethasone release behavior varies according to drug solubility and membrane thickness, and may thus be conrolled

Hypsometric Amplification of Greenland Ice Sheet Meltwater Release

Science.gov (United States)

van As, D.; Hasholt, B.; Mikkelsen, A. B.; Holtegaard Nielsen, M.; Box, J.; Claesson Liljedahl, L.; Lindback, K.; Pitcher, L. H.

2017-12-01

Proglacial discharge monitoring provides valuable insights in Greenland ice sheet meltwater release. We use a 2006-2016 discharge time series from the Watson River draining 12000 km2 of the ice sheet in southwest Greenland to investigate the large variability in catchment-total meltwater production. An observationally-constrained reconstruction of past discharge shows that meltwater release has on average increased by a factor of 1.5 since 2003 compared to the 1949-2002 period, and that interannual variability has disproportionally increased by a factor of 2.1, suggesting that melt amplifiers are at play. We derive a hypsometric amplification factor of 1.6, which is the result of the exponential melt area increase with rising temperature. Peak meltwater discharge events such as during the July 2012 flooding are due to this and other melt amplifiers, but also require intense melting over a period exceeding the multi-day transit time for high-elevation meltwater to pass through the glacial drainage system.

Population dose commitments due to radioactive releases from nuclear power plant sites in 1980

International Nuclear Information System (INIS)

Baker, D.A.; Peloquin, R.A.

1983-08-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1980. In addition doses derived from the shutdown reactors at the Three Mile Island site were included. Fifty-year dose commitments from a one-year exposure were calculated from both liquid and atmospheric releases for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each site. This report tabulates the results of these calculations, showing the dose commitments for both liquid and airborne pathways for each age group and organ. Also included for each site is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total dose commitment from both liquid and airborne pathways ranged from a high of 40 person-rem to a low of 0.02 person-rem with an arithmetic mean of 4 person-rem. The total population dose for all sites was estimated at 180 person-rem for the 96 million people considered at risk

Population dose commitments due to radioactive releases from nuclear power plant sites in 1983

International Nuclear Information System (INIS)

Baker, D.A.; Peloquin, R.A.

1987-04-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1983. Fifty-year dose commitments from a one-year exposure were calculated from both liquid and atmospheric releases for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 52 sites. This report tabulates the results of these calculations, showing the dose commitments for both liquid and airborne pathways for each age group and organ. Also included for each of the sites is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total dose commitments (from both liquid and airborne pathways) for each site ranged from a high of 45 person-rem to a low of 0.002 person-rem for the sites with plants operating throughout the year with an arithmetic mean of 3 person-rem. The total population dose for all sites was estimated at 170 person-rem for the 100 million people considered at risk

Population dose commitments due to radioactive releases from nuclear power plant sites in 1986

International Nuclear Information System (INIS)

Baker, D.A.

1989-10-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1986. Fifty-year dose commitments for a one-year exposure from both liquid and atmospheric releases were calculated for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 66 reactor sites. This report tabulates the results of these calculations, showing the dose commitments for both water and airborne pathways for each age group and organ. Also included for each of the sites is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total dose commitments (from both liquid and airborne pathways) for each site ranged from a high of 31 person-rem to a low of 0.0007 person-rem for the sites with plants operating throughout the year with an arithmetic mean of 1.7 person-rem. The total population dose for all sites was estimated at 110 person-rem for the 140 million people considered at risk. The site average individual dose commitment from all pathways ranged from a low of 2 x 10 -6 mrem to a high of 0.02 mrem. No attempt was made in this study to determine the maximum dose commitment received by any one individual from the radionuclides released at any of the sites. 12 refs

Population dose commitments due to radioactive releases from nuclear power plant sites in 1984

International Nuclear Information System (INIS)

Baker, D.A.

1988-01-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1984. Fifty-year dose commitments from a one-year exposure were calculated from both liquid and atmospheric releases for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 56 sites. This report tabulates the results of these calculations, showing the dose commitments for both liquid and airborne pathways for each age group and organ. Also included for each of the sites is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total dose commitments (from both liquid and airborne pathways) for each site ranged from a high of 110 person-rem to a low of 0.002 person-rem for the sites with plants operating throughout the year with an arithmetic mean of 5 person-rem. The total population dose for all sites was estimated at 280 person-rem for the 100 million people considered at risk. The site average individual dose commitment from all pathways ranged from a low of 6 x 10 -6 mrem to a high of 0.04 mrem. No attempt was made in this study to determine the maximum dose commitment received by any one individual from the radionuclides released at any of the sites

Population dose commitments due to radioactive releases from nuclear power plant sites in 1985

International Nuclear Information System (INIS)

Baker, D.A.

1988-08-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commericial power reactors operating during 1985. Fifty-year dose commitments from a one-year exposure were calculated from both liquid and atmospheric releases for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 61 sites. This report tabulates the results of these calculations, showing the dose commitments for both liquid and airborne pathways for each age group and organ. Also included for each of the sites is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total dose commitments (from both liquid and airborne pathways) for each site ranged from a high of 73 person-rem to a low of 0.011 person-rem for the sites with plants operating throughout the year with an arithmetic mean of 3 person-rem. The total population dose for all sites was estimated at 200 person-rem for the 110 million people considered at risk. The site average individual dose commitment from all pathways ranged from a low of 5 /times/ 10/sup /minus/6/ mrem to a high of 0.02 mrem. No attempt was made in this study to determine the maximum dose commitment received by any one individual from the radionuclides released at any of the sites

Silver nanoparticle release from commercially available plastic food containers into food simulants

International Nuclear Information System (INIS)

Mackevica, Aiga; Olsson, Mikael Emil; Hansen, Steffen Foss

2016-01-01

Silver nanoparticles (AgNPs) are currently being used in many different kinds of consumer products in order to take advantage of their antimicrobial properties. However, the potential migration of silver nanoparticles into food and subsequent consumer exposure has hardly been addressed. In the current study, we investigated four brands of commercially available plastic food storage containers and measured the total amount of silver, particle size and number concentration, and the migration rates into three different food simulants (Milli-Q grade water, 10 % ethanol, and 3 % acetic acid) for 10 days at 40 °C. The experimental setup was made according to the European Commission Directive (EU 10/2011) for articles intended to be in contact with food. The total amount of silver in plastic containers and migration solutions was quantified by ICP-MS analysis, and the size of the migrated particles was investigated by single particle ICP-MS and TEM-EDS. The total mass and median size of released particulate Ag were generally highest in 3 % acetic acid for three out of four food container brands. The total content of silver in the containers varied from 13 to 42 µg/g. The highest migration was observed in the 3 % acetic acid food simulant for all four brands of containers, with total silver release up to 3.1 ng/cm 2 after 10 days. In conclusion, the experimental results show that silver has the potential of migrating into food, especially when in contact with more acidic substances

Silver nanoparticle release from commercially available plastic food containers into food simulants

Energy Technology Data Exchange (ETDEWEB)

Mackevica, Aiga, E-mail: aima@env.dtu.dk; Olsson, Mikael Emil; Hansen, Steffen Foss [Technical University of Denmark, Department of Environmental Engineering (Denmark)

2016-01-15

Silver nanoparticles (AgNPs) are currently being used in many different kinds of consumer products in order to take advantage of their antimicrobial properties. However, the potential migration of silver nanoparticles into food and subsequent consumer exposure has hardly been addressed. In the current study, we investigated four brands of commercially available plastic food storage containers and measured the total amount of silver, particle size and number concentration, and the migration rates into three different food simulants (Milli-Q grade water, 10 % ethanol, and 3 % acetic acid) for 10 days at 40 °C. The experimental setup was made according to the European Commission Directive (EU 10/2011) for articles intended to be in contact with food. The total amount of silver in plastic containers and migration solutions was quantified by ICP-MS analysis, and the size of the migrated particles was investigated by single particle ICP-MS and TEM-EDS. The total mass and median size of released particulate Ag were generally highest in 3 % acetic acid for three out of four food container brands. The total content of silver in the containers varied from 13 to 42 µg/g. The highest migration was observed in the 3 % acetic acid food simulant for all four brands of containers, with total silver release up to 3.1 ng/cm{sup 2} after 10 days. In conclusion, the experimental results show that silver has the potential of migrating into food, especially when in contact with more acidic substances.

Population dose commitments due to radioactive releases from nuclear power plant sites in 1975

International Nuclear Information System (INIS)

Baker, D.A.; Soldat, J.K.; Watson, E.C.

1977-10-01

Population radiation dose commitments were estimated from reported radionuclide releases from commercial power reactors operating during 1975. Fifty-year dose commitments from one year exposure were calculated from both liquid and atmospheric releases for four population groups (infant, child, teenager and adult) residing between 2 and 80 km from each site. Results are given in the form of tables giving the dose commitments for both liquid and airborne pathways for each age group and organ. Also included for each site is a histogram showing the fraction of the total population within the 2 to 80-km region around each site receiving various average dose commitments from the airborne pathways. The total dose commitment from both liquid and airborne pathways ranged from a high of 750 person-rem to a low of 0.008 person-rem with an arithmetic mean of 34 person-rem

Doc2b synchronizes secretion from chromaffin cells by stimulating fast and inhibiting sustained release

DEFF Research Database (Denmark)

da Silva Pinheiro, Paulo César; de Wit, Heidi; Walter, Alexander M

2013-01-01

Synaptotagmin-1 and -7 constitute the main calcium sensors mediating SNARE-dependent exocytosis in mouse chromaffin cells, but the role of a closely related calcium-binding protein, Doc2b, remains enigmatic. We investigated its role in chromaffin cells using Doc2b knock-out mice and high temporal...... resolution measurements of exocytosis. We found that the calcium dependence of vesicle priming and release triggering remained unchanged, ruling out an obligatory role for Doc2b in those processes. However, in the absence of Doc2b, release was shifted from the readily releasable pool to the subsequent...... sustained component. Conversely, upon overexpression of Doc2b, the sustained component was largely inhibited whereas the readily releasable pool was augmented. Electron microscopy revealed an increase in the total number of vesicles upon Doc2b overexpression, ruling out vesicle depletion as the cause...

In vitro release of cholecystokinin octapeptide-like immunoreactivity from rat brain synaptosomes

International Nuclear Information System (INIS)

Klaff, L.J.; Hudson, A.; Sheppard, M.; Tyler, M.

1981-01-01

Enriched synaptosome fractions prepared by differential centrifugation and ultracentrifugation of homogenates of rat cortex, striatum, thalamus and hypothalamus contained over 65% of the total immunoreactive cholecystokinin octapeptide (CCK-8) in each area. A calcium dependent release of immunoreactive CCK-8 from these fractions in vitro in response to 2 depolarizing stimuli (60 mM KCl and 75 μM veratrine) has been demonstrated. Released CCK-8 immunoreactivity showed parallelism when serial dilutions were compared with the CCK-8 dose-response curve and eluted similarly to synthetic CCK-8 on Sephadex G-50 superfine chromatography. These results provide further evidence for a neurotransmitter or neuromodulator role for CCK-8 in brain

Participation of irradiated Anopheles arabiensis males in swarms following field release in Sudan

International Nuclear Information System (INIS)

Ageep, Tellal B; Alsharif, Bashir; Ahmed, Ayman; Salih, Elwaleed HO; Ahmed, Fayez TA; El Sayed, Badria B; Damiens, David; Gilles, Jeremie RL; Lees, Rosemary S; Diabaté, Abdoulaye

2015-01-01

BACKGROUND: The success of the SIT depends on the; release of large numbers of sterile males, which are able to; compete for mates with the wild male population within the; target area. The processes of colonisation, mass production; and irradiation may reduce the competitiveness of sterile; males through genetic selection, loss of natural traits and; somatic damage. In this context, the capacity of released; sterile Anopheles arabiensis males to survive, disperse and; participate in swarms occurring at varying distances from; the release site was studied using mark-release-recapture; techniques.; METHODS: In order to assess their participation in; swarms, irradiated and marked laboratory-reared male; mosquitoes were released 50, 100 or 200 m from the; known site of a large swarm on three consecutive nights.; Males were collected from this large swarm on subsequent; nights. Over the three days a total of 8,100 males were released.; Mean distance travelled (MDT), daily probability of; survival and estimated population size were calculated; from the recapture data. An effect of male age at the time; of release on these parameters was observed.; RESULTS: Five per cent of the males released over three; days were recaptured. In two-, three- and four-day-old; males, MDT was 118, 178 and 170 m, and the daily survival; probability 0.95, 0.90 and 0.75, respectively. From the; recapture data on the first day following each release, the; Lincoln index gives an estimation of 32,546 males in the; natural population.; DISCUSSION: Sterile An. arabiensis males released into; the field were able to find and participate in existing; swarms, and possibly even initiate swarms. The survival; probability decreased with the age of male on release but; the swarm participation and the distance travelled by older; males seemed higher than for younger males. The inclusion; of a pre-release period may thus be beneficial to male competitiveness; and increase the attractiveness of adult sexing

Naloxone inhibits superoxide but not enzyme release by human neutrophils

International Nuclear Information System (INIS)

Simpkins, C.; Alailima, S.; Tate, E.

1986-01-01

The release of toxic oxygen metabolites and enzymes by phagocytic cells is thought to play a role in the multisystemic tissue injury of sepsis. Naloxone protects septic animals. We have found that at concentrations administered to animals (10 -7 to 10 -4 M), naloxone inhibited (p 2 - ) by human neutrophils (HN), stimulated with N-formyl methionyl leucyl phenylalanine (FMLP). Naloxone had no effect on cell viability. Maximum inhibition was 65% of the total O 2 - released (13.1 nMoles/8 min/320,000 cells). FMLP-stimulated release of beta-glucoronidase or lysozyme was not altered by naloxone. Naloxone had no effect on the binding of 3 H FMLP to HN. Using 3 H naloxone and various concentrations of unlabeled naloxone higher affinity (K/sub D/ = 12nM) and lower affinity (K/sub D/ = 4.7 x 10 -5 ) binding sites were detected. The K/sub D/ of the low affinity site corresponded to the ED 50 for naloxone inhibition of O 2 - (1 x 10 -5 M). Binding to this low affinity site was decreased by (+) naloxone, beta-endorphin and N acetyl beta-endorphin, but not by leu-enkephalin, thyrotropin releasing factor, prostaglandin D 2 or E 2 . Conclusions: (1) naloxone inhibits FMLP-stimulated O 2 but not enzyme release, (2) this inhibition is not due to alteration of FMLP receptor binding, (3) naloxone may act via a low affinity binding site which is ligand specific, and (4) a higher affinity receptor is present on HN

ATP Release Channels

Directory of Open Access Journals (Sweden)

Akiyuki Taruno

2018-03-01

Full Text Available Adenosine triphosphate (ATP has been well established as an important extracellular ligand of autocrine signaling, intercellular communication, and neurotransmission with numerous physiological and pathophysiological roles. In addition to the classical exocytosis, non-vesicular mechanisms of cellular ATP release have been demonstrated in many cell types. Although large and negatively charged ATP molecules cannot diffuse across the lipid bilayer of the plasma membrane, conductive ATP release from the cytosol into the extracellular space is possible through ATP-permeable channels. Such channels must possess two minimum qualifications for ATP permeation: anion permeability and a large ion-conducting pore. Currently, five groups of channels are acknowledged as ATP-release channels: connexin hemichannels, pannexin 1, calcium homeostasis modulator 1 (CALHM1, volume-regulated anion channels (VRACs, also known as volume-sensitive outwardly rectifying (VSOR anion channels, and maxi-anion channels (MACs. Recently, major breakthroughs have been made in the field by molecular identification of CALHM1 as the action potential-dependent ATP-release channel in taste bud cells, LRRC8s as components of VRACs, and SLCO2A1 as a core subunit of MACs. Here, the function and physiological roles of these five groups of ATP-release channels are summarized, along with a discussion on the future implications of understanding these channels.

Global analysis and parametric dependencies for potential unintended hydrogen-fuel releases

Energy Technology Data Exchange (ETDEWEB)

Harstad, Kenneth; Bellan, Josette [Jet Propulsion Laboratory, California Institute of Technology, 4800 Oak Grove Drive, M/S 125-109, Pasadena, CA 91109-8099 (United States)

2006-01-01

Global, simplified analyses of gaseous-hydrogen releases from a high-pressure vessel and liquid-hydrogen pools are conducted for two purposes: (1) establishing order-of-magnitude values of characteristic times and (2) determining parametric dependencies of these characteristic times on the physical properties of the configuration and on the thermophysical properties of hydrogen. According to the ratio of the characteristic release time to the characteristic mixing time, two limiting configurations are identified: (1) a rich cloud exists when this ratio is much smaller than unity, and (2) a jet exists when this ratio is much larger than unity. In all cases, it is found that the characteristic release time is proportional to the total released mass and inversely proportional to a characteristic area. The approximate size, convection velocity, and circulation time of unconfined burning-cloud releases scale with the cloud mass at powers 1/3, 1/6, and 1/6, respectively, multiplied by an appropriately dimensional constant; the influence of cross flow can only be important if its velocity exceeds that of internal convection. It is found that the fireball lifetime is approximately the maximum of the release time and thrice the convection-associated characteristic time. Transition from deflagration to detonation can occur only if the size of unconfined clouds exceeds by a factor of O(10) that of a characteristic detonation cell, which ranges from 0.015 m under stoichiometric conditions to approximately 1 m under extreme rich/lean conditions. For confined vapor pockets, transition occurs only for pocket sizes larger than the cell size. In jets, the release time is inversely proportional to the initial vessel pressure and has a square root dependence on the vessel temperature. Jet velocities are a factor of 10 larger than convective velocities in fireballs and combustion is possible only in the subsonic, downstream region where entrainment may occur.

Individual radiation doses from unit releases of long lived radionuclides

International Nuclear Information System (INIS)

Bergstroem, U.; Nordlinder, S.

1990-04-01

The turn-over in a standard biosphere of radionuclides, disposed in a repository for high level waste was studied from a dose point of view. A multi-compartment model with unit releases to the biosphere was designed and solved by the BIOPATH-code. The uncertainty in the results due to the uncertainty in input parameter values were examined for all nuclides with the PRISM-system. Adults and five year old children were exposed from 10 different exposure pathways originating from activity in well and lake water. The results given as total doses per year and Bq release (conversion factors) can be used in combination with leakage rates from the geosphere for safety analysis of a repository. The conversion factors obtained (arithmetic mean values), are given. (65 refs.) (authors)

Effluents and releases of tritium from Novo-Voronezh-5 reactor

International Nuclear Information System (INIS)

Babenko, A.G.; Mekhedov, B.N.; Podporinova, L.E.; Popov, S.V.; Shalin, A.N.

1990-01-01

Results of systematic measurements of tritium concentration within technological systems of reactor of Novo-Voronezh NPP conducted to evaluate tritium effluents and releases and radiation doses to population from these effluents and releases are given. It is shown that 68% concerning tritium total amount were disposed into sewerage while 17% - through vent tube and 15% - with water and steam from secondary circuit systems. Standartized tritium effluents from WWER-1000 reactor for 5 year run constitute 15±1.9 GBq/MWxyear and it corresponds to mean value of effluents for foreign NPPs. Tritium concentration in the atmosphere constituted according to calculations (4.1-20)x10 -5 Bq/l. Conclusion is made about insignificant dose to population from tritium gaseous effluents. Detail study is necessary for dose connected with tritium contained in water effluents

Quality assessment of the Ozone_cci Climate Research Data Package (release 2017) - Part 1: Ground-based validation of total ozone column data products

Science.gov (United States)

Garane, Katerina; Lerot, Christophe; Coldewey-Egbers, Melanie; Verhoelst, Tijl; Elissavet Koukouli, Maria; Zyrichidou, Irene; Balis, Dimitris S.; Danckaert, Thomas; Goutail, Florence; Granville, Jose; Hubert, Daan; Keppens, Arno; Lambert, Jean-Christopher; Loyola, Diego; Pommereau, Jean-Pierre; Van Roozendael, Michel; Zehner, Claus

2018-03-01

The GOME-type Total Ozone Essential Climate Variable (GTO-ECV) is a level-3 data record, which combines individual sensor products into one single cohesive record covering the 22-year period from 1995 to 2016, generated in the frame of the European Space Agency's Climate Change Initiative Phase II. It is based on level-2 total ozone data produced by the GODFIT (GOME-type Direct FITting) v4 algorithm as applied to the GOME/ERS-2, OMI/Aura, SCIAMACHY/Envisat and GOME-2/Metop-A and Metop-B observations. In this paper we examine whether GTO-ECV meets the specific requirements set by the international climate-chemistry modelling community for decadal stability long-term and short-term accuracy. In the following, we present the validation of the 2017 release of the Climate Research Data Package Total Ozone Column (CRDP TOC) at both level 2 and level 3. The inter-sensor consistency of the individual level-2 data sets has mean differences generally within 0.5 % at moderate latitudes (±50°), whereas the level-3 data sets show mean differences with respect to the OMI reference data record that span between -0.2 ± 0.9 % (for GOME-2B) and 1.0 ± 1.4 % (for SCIAMACHY). Very similar findings are reported for the level-2 validation against independent ground-based TOC observations reported by Brewer, Dobson and SAOZ instruments: the mean bias between GODFIT v4 satellite TOC and the ground instrument is well within 1.0 ± 1.0 % for all sensors, the drift per decade spans between -0.5 % and 1.0 ± 1.0 % depending on the sensor, and the peak-to-peak seasonality of the differences ranges from ˜ 1 % for GOME and OMI to ˜ 2 % for SCIAMACHY. For the level-3 validation, our first goal was to show that the level-3 CRDP produces findings consistent with the level-2 individual sensor comparisons. We show a very good agreement with 0.5 to 2 % peak-to-peak amplitude for the monthly mean difference time series and a negligible drift per decade of the differences in the Northern Hemisphere

Release kinetics of tocopherol and quercetin from binary antioxidant controlled-release packaging films.

Science.gov (United States)

Chen, Xi; Lee, Dong Sun; Zhu, Xuntao; Yam, Kit L

2012-04-04

This paper investigated the feasibility of manipulating packaging polymers with various degrees of hydrophobicity to release two antioxidants, tocopherol and quercetin, at rates suitable for long-term inhibition of lipid oxidation in food. For example, one antioxidant can be released at a fast rate to provide short-term/intermediate protection, whereas the other antioxidant can be released at a slower rate to provide intermediate/long-term protection of lipid oxidation. Controlled-release packaging films containing tocopherol and quercetin were produced using ethylene vinyl alcohol (EVOH), ethylene vinyl acetate (EVA), low-density polyethylene (LDPE), and polypropylene (PP) polymers; the release of these antioxidants to 95% ethanol (a fatty food simulant) was measured using UV-vis spectrophotometry, and Fickian diffusion models with appropriate initial and boundary conditions were used to fit the data. For films containing only quercetin, the results show that the release of quercetin was much faster but lasted for a much shorter time for hydrophilic polymers (EVOH and EVA) than for hydrophobic polymers (LDPE and PP). For binary antioxidant films containing tocopherol and quercetin, the results show that tocopherol released more rapidly but for a shorter period of time than quercetin in LDPE and EVOH films, and the difference is more pronounced for LDPE films than EVOH films. The results also show the presence of tocopherol can accelerate the release of quercetin. Although none of the films produced is acceptable for long-term lipid oxidation inhibition, the study provides encouraging results suggesting that acceptable films may be produced in the future using polymer blend films.

Liquid-Phase Heat-Release Rates of the Systems Hydrazine-Nitric Acid and Unsymmetrical Dimethylhydrazine-Nitric Acid

Science.gov (United States)

Somogyi, Dezso; Feiler, Charles E.

1960-01-01

The initial rates of heat release produced by the reactions of hydrazine and unsymmetrical dimethylhydrazine with nitric acid were determined in a bomb calorimeter under conditions of forced mixing. Fuel-oxidant weight ratio and injection velocity were varied. The rate of heat release apparently depended on the interfacial area between the propellants. Above a narrow range of injection velocities representing a critical amount of interfacial area, the rates reached a maximum and were almost constant with injection velocity. The maximum rate for hydrazine was about 70 percent greater than that for unsymmetrical dimethylhydrazine. The total heat released did not vary with mixture ratio over the range studied.

Lateral patellar retinacular release: changes over the last ten years

Directory of Open Access Journals (Sweden)

Leonardo Pini Rosalem Marciano da Fonseca

Full Text Available ABSTRACT Lateral retinacular release is a useful resource in knee surgery that can be used for disorders of the extensor mechanism. For many years, it was indiscriminately used in the treatment of the various patellofemoral joint alterations, with conflicting functional results. This study aimed to analyze the changes that have occurred in the indications and clinical effectiveness of lateral retinacular release by reviewing the relevant literature of the past ten years, comparing it to the classic literature on the subject. It was found that less extensive releases decompress the lateral patellar facet, helping with pain control, while decreasing the risks of medial subluxation. Nowadays, there is clear evidence for its indication in the lateral patellar hypercompression syndrome associated with anterior knee pain, as long as there is no related instability; furthermore, it will normally play an adjuvant role in extensor mechanism alignment surgeries for cases of recurrent patellar instability. The initial results for symptomatic patellofemoral osteoarthritis are promising when lateral release is combined with cartilage debridement; in total knee replacement, it is more commonly used for the correction of valgus deformity in order to improve the components’ congruency. Finally, distinguishing the different patellofemoral joint pathologies is seen as crucial in order to indicate this procedure. Further randomized control trials that compare surgical techniques with long-term results are still needed.

A study of 60 patients with percutaneous trigger finger releases: clinical and ultrasonographic findings.

Science.gov (United States)

Gulabi, D; Cecen, G S; Bekler, H I; Saglam, F; Tanju, N

2014-09-01

We present the clinical results and ultrasonographic findings of 61 trigger digits treated with percutaneous A1 pulley release. An endoscopic carpal tunnel knife was used for the release in the outpatient department. The mean follow-up period was 3.5 months. A total of 55 digits (90%) had complete relief of their triggering postoperatively. Six digits (10%) had Grade 2 triggering clinically in the early postoperative period.The complications included six cases of insufficient release (10%), scar sensitivity in one patient, short-term hypoaesthesia in three digits (5%), and flexor tendon laceration noted on postoperative ultrasonography in eight digits (13%). No neurovascular damage was noted on the postoperative ultrasonography. Ultrasonograpy provides information about tendon laceration and changes in thickness of the pulleys and confirm A1 pulley release after surgery, but it does not alter clinical decision-making. We believe that pre- and postoperative ultrasonograpy does not need to be included as a routine examination. © The Author(s) 2014.

Can gamma irradiation during radiotherapy influence the metal release process for biomedical CoCrMo and 316L alloys?

Science.gov (United States)

Wei, Zheng; Edin, Jonathan; Karlsson, Anna Emelie; Petrovic, Katarina; Soroka, Inna L; Odnevall Wallinder, Inger; Hedberg, Yolanda

2018-02-09

The extent of metal release from implant materials that are irradiated during radiotherapy may be influenced by irradiation-formed radicals. The influence of gamma irradiation, with a total dose of relevance for radiotherapy (e.g., for cancer treatments) on the extent of metal release from biomedical stainless steel AISI 316L and a cobalt-chromium alloy (CoCrMo) was investigated in physiological relevant solutions (phosphate buffered saline with and without 10 g/L bovine serum albumin) at pH 7.3. Directly after irradiation, the released amounts of metals were significantly higher for irradiated CoCrMo as compared to nonirradiated CoCrMo, resulting in an increased surface passivation (enhanced passive conditions) that hindered further release. A similar effect was observed for 316L showing lower nickel release after 1 h of initially irradiated samples as compared to nonirradiated samples. However, the effect of irradiation (total dose of 16.5 Gy) on metal release and surface oxide composition and thickness was generally small. Most metals were released initially (within seconds) upon immersion from CoCrMo but not from 316L. Albumin induced an increased amount of released metals from AISI 316L but not from CoCrMo. Albumin was not found to aggregate to any greater extent either upon gamma irradiation or in the presence of trace metal ions, as determined using different light scattering techniques. Further studies should elucidate the effect of repeated friction and fractionated low irradiation doses on the short- and long term metal release process of biomedical materials. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2018. © 2018 The Authors Journal of Biomedical Materials Research Part B: Applied Biomaterials Published by Wiley Periodicals, Inc.

Dose apportionment using statistical modeling of the effluent release

International Nuclear Information System (INIS)

Datta, D.

2011-01-01

Nuclear power plants are always operated under the guidelines stipulated by the regulatory body. These guidelines basically contain the technical specifications of the specific power plant and provide the knowledge of the discharge limit of the radioactive effluent into the environment through atmospheric and aquatic route. However, operational constraints sometimes may violate the technical specification due to which there may be a failure to satisfy the stipulated dose apportioned to that plant. In a site having multi facilities sum total of the dose apportioned to all the facilities should be constrained to 1 mSv/year to the members of the public. Dose apportionment scheme basically stipulates the limit of the gaseous and liquid effluent released into the environment. Existing methodology of dose apportionment is subjective in nature that may result the discharge limit of the effluent in atmospheric and aquatic route in an adhoc manner. Appropriate scientific basis for dose apportionment is always preferable rather than judicial basis from the point of harmonization of establishing the dose apportionment. This paper presents an attempt of establishing the discharge limit of the gaseous and liquid effluent first on the basis of the existing value of the release of the same. Existing release data for a few years (for example 10 years) for any nuclear power station have taken into consideration. Bootstrap, a resampling technique, has been adopted on this data sets to generate the population which subsequently provide the corresponding population distribution of the effluent release. Cumulative distribution of the population distribution obtained is constructed and using this cumulative distribution, 95th percentile (upper bound) of the discharge limit of the radioactive effluents is computed. Dose apportioned for a facility is evaluated using this estimated upper bound of the release limit. Paper describes the detail of the bootstrap method in evaluating the

SIMULATION OF VINPOCETINE RELEASE PROCESS FROM MICROCAPSULES WITH HYDROPHOBIC SHELL

Directory of Open Access Journals (Sweden)

Yu. A. Polkovnikova

2017-01-01

Full Text Available Nowadays microcapsules are widely spread in different industries. Microcapsules with vitamins, etheric and fatty oils are included into different cosmetics (creams, gels, serums. Microencapsulated probiotics are used in foods and fodder additives in veterinary. An important field of application of microencapsulation in pharmacy is the combination in the total dosage of drugs that are incompatible when mixed in free form.The aim of work is a comparative analysis of thermodynamic characteristics of vinpocetine release from the melt of beeswax and cacao butter 3:2 into water, solution of hydrochloric acid 0.01 M and ethanol.Materials and methods. For simulation of the process of vinpocetine release from the melt into different environments models component models of the studied systems were built and their atom charges were calculated by quantum-chemical method. Spatial models of the components were built in Hyper Chem 8.01. As an initial state for the thermodynamic characteristics of the calculation of vinpocetine release from the melt, a conformation of «melt-vinpocetine» system was used after thermodynamic equilibration by molecular dynamics simulation in Bioeurica program for 5 ns. For isolated systems a vibrational analysis was performed with the use of unrestricted Hartree-Fock method in STO-3G basis set in Orca 4.0 program.Results and discussion. Vinpocetine release from the melt of beeswax and cacao butter 3:2 into water with different pH values and to ethanol depends on its solubility in these environments, and also on solubility of the melt.Conclusion. The performed study of vinpocetine release from the melt of beeswax and cacao butter 3:2 by molecular dynamics simulation demonstrates the opportunity of vinpocetine release into water with pH=2 and into ethanol. The obtained results make it possible to assume a lower degree of vinpocetine release from the melt into ethanol compared with the solution of hydrochloric acid 0,01 M.

Mechanical properties and total hydroxycinnamic derivative release of starch/glycerol/Melissa officinalis extract films

Directory of Open Access Journals (Sweden)

Letícia Mello Rechia

2010-09-01

Full Text Available The aim of this study was to investigate the mechanical properties of starch/glycerol/Melissa officinalis, a topical drug delivery system for labial herpes treatment. Four films were prepared with different concentrations of starch, glycerol, and Melissa officinalis extract. The results revealed that increasing the glycerol concentration in the film reduced elasticity modulus and tensile strength, exhibiting a plasticizing effect. The increase in free volume resulted in increased release of hydroxycinnamic derivatives expressed as rosmarinic acid.O objetivo deste trabalho foi estudar as propriedades mecânicas e o mecanismo de liberação de um sistema tópico de liberação prolongada para o tratamento do Herpes labial a partir de filmes de amido/glicerol/extrato de Melissa officinalis, planta com comprovada atividade antiviral. Foram obtidos quatro filmes poliméricos com diferentes concentrações de amido, glicerol e extrato de Melissa officinalis os quais foram caracterizados mecanicamente e determinado o perfil de liberação de derivados hidroxicinâmicos. Os resultados demonstraram que o aumento da concentração de glicerol no filme produz uma redução no módulo de elasticidade e na tensão de deformação como conseqüência do efeito plastificante. O aumento no volume livre do polímero resultou em aumento da liberação dos derivados hidroxicinâmicos expressos como ácido rosmarínico.

Controlled-release tablet formulation of isoniazid.

Science.gov (United States)

Jain, N K; Kulkarni, K; Talwar, N

1992-04-01

Guar (GG) and Karaya gums (KG) alone and in combination with hydroxy-propylmethylcellulose (HPMC) were evaluated as release retarding materials to formulate a controlled-release tablet dosage form of isoniazid (1). In vitro release of 1 from tablets followed non-Fickian release profile with rapid initial release. Urinary excretion studies in normal subjects showed steady-state levels of 1 for 13 h. In vitro and in vivo data correlated (r = 0.9794). The studies suggested the potentiality of GG and KG as release retarding materials in formulating controlled-release tablet dosage forms of 1.

Population dose commitments due to radioactive releases from nuclear power plant sites in 1981. Volume 3

International Nuclear Information System (INIS)

Baker, D.A.; Peloquin, R.A.

1985-01-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1981. Fifty-year dose commitments from a one-year exposure were calculated from both liquid and atmospheric releases for four population groups (infant, child, teenager and adult) residing between 2 and 80 km from each site. This report tabulates the results of these calculations, showing the dose commitments for both liquid and airborne pathways for each age group and organ. Also included for each site is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total dose commitment from both liquid and airborne pathways from 48 sites ranged from a high of 20 person-rem to a low of 0.008 person-rem with an arithmetic mean of 3 person-rem. The total population dose for all sites was estimated at 160 person-rem for the 98 million people considered at risk

A method of radiocompetitive assay of total thyroxine in the serum by means of enzymatic release of thyroxine from the transporting proteins

International Nuclear Information System (INIS)

Snarski, A.; Wyrwinski, J.

1978-01-01

Pepsin causes denaturation of the transporting proteins and liberates thyroxine which can be assayed by the radiocompetitive method. Change of the pH of the medium from acid to alkaline inactivates irreveribly pepsin. The enzymatic release of thyroxine is much simpler that the method of ethanol extraction and thermal denaturation of the transporting proteins applied up to now. The new technique of thyroxine release has been introduced for radiocompetitive determination of thyroxine using dextran coated charcoal for adsorption of the free hormone. A new method has been elaborated for preparation of working standards of thyroxine in a mixture of pepsin solution with hormone-free serum. The method is efficient and rapid. The normal range is from 50 to 130 nanomol/l. Over 7 000 determinations were done as yet in patients with suspected thyroid function disturbances. (author)

Use of antibiotic-loaded cement in total knee arthroplasty.

OpenAIRE

Hinarejos Gómez, Pedro Angel; Guirro Castellnou, Pau; Puig Verdié, Luís; Torres Claramunt, Raúl; Leal Blanquet, Joan; Sánchez Soler, JF.; Monllau García, Juan Carlos

2015-01-01

Bone cement has the capacity to release antibiotic molecules if any antibiotic is included in it, and these elution properties are improved as cement porosity is increased. In vitro studies have shown high local antibiotic concentration for many hours or few days after its use. Antibiotic loaded bone cement (ALBC) is helpful when treating an infection in total knee arthroplasty (TKA) revision surgery. The purpose of this paper was to review the evidence for the routine use of ALBC in TKA in t...

Formulation and in vitro evaluation of sustained release matrix tablets using cross-linked natural gum.

Science.gov (United States)

Jamil, Qurratul Ain; Masood, Muhammad Irfan; Jamil, Muhammad Nauman; Masood, Imran; Iqbal, Shahid Muhammad

2017-03-01

Polysaccharide gums because of their biocompatibility, biodegradability and non-immunogenic properties are considered as the best choice for preparing sustained release tablets as compared to their synthetic counterpart. The cross linking of natural gums in matrix tablets increase the sustained release property of matrix tablets. Isoniazid is a first line therapy of tuberculosis, belongs to BCS I with half-life of 3-4 hours. These characteristics make isoniazid a good candidate for sustained release dosage form. Karaya gum crossed linked with trisodium tri metaphosphate was used as release rate retardant for preparing isoniazid cross-linked matrix tablet. Total 8 sustained release formulations were prepared. Both granules and tablets were evaluated under in vitro condition against different parameters. Dissolution studies were performed with all eight formulations for 12 hours using USP apparatus I. Four formulations designated as F1, F2, F3, F4 have drug and karaya gum while other four formulations F5, F6, F7, F8 have drug and crossed linked polymer in ratios of 1:1, 1:2, 1:3 and 1:4 respectively. Dissolution data was analyzed by using different kinetic models. Best fit model for most efficient formulation was zero order while release mechanism was super case I. Formulation 8 showed sufficiently slow release kinetics and about 83% of drug was released in 10 hours, indicating that cross-linked karaya gum proved efficient in preparing sustained release tablets.

The effect of helium generation and irradiation temperature on tritium release from neutron irradiated beryllium

International Nuclear Information System (INIS)

Kupriyanov, I.B.; Gorokhov, V.A.; Vlasov, V.V.; Kovalev, A.M.; Chakin, V.P.

2004-01-01

The effect of neutron irradiation condition on tritium release from beryllium is described in this paper. Beryllium samples were irradiated in the SM reactor with neutron fluence (E > 0.1 MeV) of (0.37-2.0) x 10 22 cm -2 at 70-100degC and 650-700degC. Mass-spectrometer technique was used in out of tritium release experiments during stepped-temperature anneal within a temperature range from 250 to 1300degC. The total amount of helium accumulated in irradiated beryllium samples varied from 521 appm to 3061 appm. The first signs of tritium release were detected at temperature of 406-553degC. It was shown that irradiation temperature and helium generation level significantly affect the tritium release. A fraction of 44 - 74 % of tritium content in samples irradiated at low temperature (70 - 100degC) is release from beryllium at an annealing temperature below 800degC, whereas for samples after high temperature irradiation (650 - 700 degC) tritium release did not exceed 14 %. Majority of tritium (∼68%) is released within a temperature range from 800 to 920 degC. The increase of helium generation from 521 appm to 3061 appm results in lowering the temperature of maximal tritium release rate and the upper temperature of tritium release from beryllium by 100-130degC and 200-240degC, correspondingly. On the basis of data obtained, the diffusion coefficients of tritium in beryllium were calculated. (author)

Corticotropin-releasing hormone and pituitary-adrenal hormones in pregnancies complicated by chronic hypertension.

Science.gov (United States)

Warren, W B; Gurewitsch, E D; Goland, R S

1995-02-01

We hypothesized that maternal plasma corticotropin-releasing hormone levels are elevated in chronic hypertension and that elevations modulate maternal and fetal pituitary-adrenal function. Venous blood samples and 24-hour urine specimens were obtained in normal and hypertensive pregnancies at 21 to 40 weeks of gestation. Corticotropin-releasing hormone, corticotropin, cortisol, dehydroepiandrosterone sulfate, and total estriol levels were measured by radioimmunoassay. Mean hormone levels were compared by unpaired t test or two-way analysis of variance. Plasma corticotropin-releasing hormone levels were elevated early in hypertensive pregnancies but did not increase after 36 weeks. Levels of pituitary and adrenal hormones were not different in normal and hypertensive women. However, maternal plasma estriol levels were lower in hypertensive pregnancies compared with normal pregnancies. Fetal 16-hydroxy dehydroepiandrosterone sulfate, the major precursor to placental estriol production, has been reported to be lower than normal in hypertensive pregnancies, possibly explaining the decreased plasma estriol levels reported here. Early stimulation of placental corticotropin-releasing hormone production or secretion may be related to accelerated maturation of placental endocrine function in pregnancies complicated by chronic hypertension.

Cobalt release from inexpensive jewellery

DEFF Research Database (Denmark)

Thyssen, Jacob Pontoppidan; Jellesen, Morten Stendahl; Menné, Torkil

2010-01-01

. Conclusions: This study showed that only a minority of inexpensive jewellery purchased in Denmark released cobalt when analysed with the cobalt spot test. As fashion trends fluctuate and we found cobalt release from dark appearing jewellery, cobalt release from consumer items should be monitored in the future......Objectives: The aim was to study 354 consumer items using the cobalt spot test. Cobalt release was assessed to obtain a risk estimate of cobalt allergy and dermatitis in consumers who would wear the jewellery. Methods: The cobalt spot test was used to assess cobalt release from all items...

Evaluation of release amount of radioactivity from Chernobyl accident and of resulting radiological consequence in China

International Nuclear Information System (INIS)

Zhang Yongxing

1987-01-01

Three kinds of methods are used to evaluate the release amount from Chernoby1 RBMK-1000 reactor accident, i.e. (1) estimation by comparison with Windscale accident; (2) estimation in terms of the stock in the core; and (3) estimation according to the available monitoring data form adjacent countries such as Poland and Finland. The results obtained are as follows: the release of I-131 was 0.1-1.5 EBq, which is approximately 4-50% of the stock in the core; the release amount of Ru-103 was comparable to that of Cs-137, both approximately 5-10% of that of I-131; the volatile nuclides such as Mo-99, Ru-103, Te-132, Cs-137 etc., were in the order of 0.4 EBq; involatile nuclides were 0.2 EBq; noble gases and other fission products 10 EBq; and the total amount released was about 20 EBq, which taken together 8% of the stock in the core. The radioactive cloud cluster passed through over the area of China in the beginning of May. It was estimated that the total amount of I-131 in air over China area was about 1.6 PB q , Cs-137 about 0.3 PB q , Ru-103 about 0.2 PB q ; the total fallout in the area of China was about 3 PB q for I-131, about 0.1 PB q for Cs-137, about 0.3 PB q for Ru-103. The resulting effective dose equavalent commitment to critical group individual was about 60 μSv, collective effective dose equavalent commitment received by the population of China was about 1 x 10 4 man.Sv

Release of Growth Factors into Root Canal by Irrigations in Regenerative Endodontics.

Science.gov (United States)

Zeng, Qian; Nguyen, Sean; Zhang, Hongming; Chebrolu, Hari Priya; Alzebdeh, Dalia; Badi, Mustafa A; Kim, Jong Ryul; Ling, Junqi; Yang, Maobin

2016-12-01

The aim of this study was to investigate the release of growth factors into root canal space after the irrigation procedure of regenerative endodontic procedure. Sixty standardized root segments were prepared from extracted single-root teeth. Nail varnish was applied to all surfaces except the root canal surface. Root segments were irrigated with 1.5% NaOCl + 17% EDTA, 2.5% NaOCl + 17% EDTA, 17% EDTA, or deionized water. The profile of growth factors that were released after irrigation was studied by growth factor array. Enzyme-linked immunosorbent assay was used to validate the release of transforming growth factor (TGF)-β1 and basic fibroblast growth factor (bFGF) at 4 hours, 1 day, and 3 days after irrigation. The final concentrations were calculated on the basis of the root canal volume measured by cone-beam computed tomography. Dental pulp stem cell migration on growth factors released from root segments was measured by using Transwell assay. Total of 11 of 41 growth factors were detected by growth factors array. Enzyme-linked immunosorbent assay showed that TGF-β1 was released in all irrigation groups. Compared with the group with 17% EDTA (6.92 ± 4.49 ng/mL), the groups with 1.5% NaOCl + 17% EDTA and 2.5% NaOCl + 17% EDTA had significantly higher release of TGF-β1 (69.04 ± 30.41 ng/mL and 59.26 ± 3.37 ng/mL, respectively), with a peak release at day 1. The release of bFGF was detected at a low level in all groups (0 ng/mL to 0.43 ± 0.22 ng/mL). Migration assay showed the growth factors released from root segments induced dental pulp stem cell migration. The root segment model in present study simulated clinical scenario and indicated that the current irrigation protocol released a significant amount of TGF-β1 but not bFGF. The growth factors released into root canal space induced dental pulp stem cell migration. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Controlled drug release on amine functionalized spherical MCM-41

International Nuclear Information System (INIS)

Szegedi, Agnes; Popova, Margarita; Goshev, Ivan; Klébert, Szilvia; Mihály, Judit

2012-01-01

MCM-41 silica with spherical morphology and small particle sizes (100 nm) was synthesized and modified by post-synthesis method with different amounts of 3-aminopropyltriethoxysilane (APTES). A comparative study of the adsorption and release of a model drug, ibuprofen, was carried out. The modified and drug loaded mesoporous materials were characterized by XRD, TEM, N 2 physisorption, elemental analysis, thermal analysis and FT-IR spectroscopy. A new method was developed for the quantitative determination of amino groups in surface modified mesoporous materials by the ninhydrin reaction. Good correlation was found between the amino content of the MCM-41 materials determined by the ninhydrin method and their ibuprofen adsorption capacity. Amino modification resulted in high degree of ibuprofen loading and slow release rate in comparison to the parent non-modified MCM-41. - Graphical abstract: Determination of surface amino groups by ninhidrin method. Highlights: ► Spherical MCM-41 modified by different amounts of APTES was studied. ► Ibuprofen (IBU) adsorption and release characteristics was tested. ► The ninhydrin reaction was used for the quantitative determination of amino groups. ► Stoichiometric amount of APTES is enough for totally covering the surface with amino groups. ► Good correlation was found between the amino content and IBU adsorption capacity.

Relative Release-to-Birth Indicators for Investigating TRISO Fuel Fission Gas Release Models

International Nuclear Information System (INIS)

Harp, Jason M.; Hawari, Ayman I.

2008-01-01

TRISO microsphere fuel is the fundamental fuel unit for Very High Temperature Reactors (VHTR). A single TRISO particle consists of an inner kernel of uranium dioxide or uranium oxycarbide surrounded by layers of pyrolytic carbon and silicon carbide. If the silicon carbide layer fails, fission products, especially the noble fission gases Kr and Xe, will begin to escape the failed particle. The release of fission gas is usually quantified by measuring the ratio of the released activity (R) to the original birth activity (B), which is designated as the R/B ratio. In this work, relative Release-to-Birth indicators (I) are proposed as a technique for interpreting the results of TRISO irradiation experiments. By implementing a relative metric, it is possible to reduce the sensitivity of the indicators to instrumental uncertainties and variations in experimental conditions. As an example, relative R/B indicators are applied to the interpretation of representative data from the Advanced Gas Reactor-1 TRISO fuel experiment that is currently taking place at the Advanced Test Reactor of Idaho National Laboratory. It is shown that the comparison of measured to predicted relative R/B indicators (I) gives insight into the physics of release and helps validate release models. Different trends displayed by the indicators are related to the mechanisms of fission gas release such as diffusion and recoil. The current analysis shows evidence for separate diffusion coefficients for Kr and Xe and supports the need to account for recoil release. (authors)

Photoimages and the release characteristics of lipophilic matrix tablets containing highly water-soluble potassium citrate with high drug loadings.

Science.gov (United States)

Cao, Qing-Ri; Kim, Tae-Wan; Lee, Beom-Jin

2007-07-18

Two types of the carnauba wax-based lipophilic matrix tablet using spray-dried granules (SDT) or directly compressible powdered mixtures (DCT) were prepared for sustained release. The model drug was a highly water-soluble potassium citrate and loaded about 74% of the total tablet weight. The SDT slowly eroded and disintegrated during the release study without showing sustained release when the hydrophilic excipients were added. In contrast, the DCT was more efficient for sustained release. The release rate decreased with increasing carnauba wax concentration. In particular, the sustained release rate was markedly pronounced when the lipophilic stearyl alcohol and stearic acid were combined with the carnauba wax. The surface of the intact DCT appeared to be smooth and rusty. The DCT rose to the surface from the bottom of the vessel during the release test, and numerous pores and cracks with no signs of disintegration were also observed after the release test. The release profile was dependent on the formulation composition and preparation method of the matrix tablet. Diffusion-controlled leaching through the channels of the pores and cracks of the lipophilic matrix tablet (DCT) is a key to the sustained release.

Two DNA glycosylases in Esherichia coli which release primarily 3-methyladenine

International Nuclear Information System (INIS)

Thomas, L.; Yang, C.; Goldthwait, D.A.

1982-01-01

Two enzymes have been partially purified from Escherichia coli and designated 3-methyladenine DNA glycosylases I and II. The apparent molecular weight of glycosylase I is 20,000, and that of II is 27,000. Glycosylase I releases 3-methyladenine (3-MeA) while II releases 3-MeA, 3-methylguanine (3-MeG), 7-methylguanine (7-MeG), and 7-methyladenine (7-MeA). The rate of release of 3-MeA by glycosylase II is 30 times that of 7-MeG. Glycosylase I is missing in mutants tag 1 and tag 2. In crude extracts, the 3-MeA activity of II is approximately 10% of the total 3-MeA activity. A 50% inactivation at 48 0 C required 5 min for I and 65 min for II. The 3-MeA and 7-MeG activities of the glycosylase II preparation could not be separated by isoelectric focusing, by chromatography of DEAE, Sephadex G-100, phosphocellulose, DNA-cellulose, or carboxymethylcellulose, or by heating at 50 0 C

Drug release from non-aqueous suspensions. II. The release of methylxanthines from paraffin suspensions

NARCIS (Netherlands)

Blaey, C.J. de; Fokkens, J.G.

1984-01-01

The release of 3 methylxanthines, i.e. caffeine, theobromine and theophylline, from suspensions in liquid paraffin to an aqueous phase was determined in an in vitro apparatus. The release rates were determined as a function of the pH of the aqueous phase. It was proved that the release process was

Shear stress-induced mitochondrial biogenesis decreases the release of microparticles from endothelial cells.

Science.gov (United States)

Kim, Ji-Seok; Kim, Boa; Lee, Hojun; Thakkar, Sunny; Babbitt, Dianne M; Eguchi, Satoru; Brown, Michael D; Park, Joon-Young

2015-08-01

The concept of enhancing structural integrity of mitochondria has emerged as a novel therapeutic option for cardiovascular disease. Flow-induced increase in laminar shear stress is a potent physiological stimulant associated with exercise, which exerts atheroprotective effects in the vasculature. However, the effect of laminar shear stress on mitochondrial remodeling within the vascular endothelium and its related functional consequences remain largely unknown. Using in vitro and in vivo complementary studies, here, we report that aerobic exercise alleviates the release of endothelial microparticles in prehypertensive individuals and that these salutary effects are, in part, mediated by shear stress-induced mitochondrial biogenesis. Circulating levels of total (CD31(+)/CD42a(-)) and activated (CD62E(+)) microparticles released by endothelial cells were significantly decreased (∼40% for both) after a 6-mo supervised aerobic exercise training program in individuals with prehypertension. In cultured human endothelial cells, laminar shear stress reduced the release of endothelial microparticles, which was accompanied by an increase in mitochondrial biogenesis through a sirtuin 1 (SIRT1)-dependent mechanism. Resveratrol, a SIRT1 activator, treatment showed similar effects. SIRT1 knockdown using small-interfering RNA completely abolished the protective effect of shear stress. Disruption of mitochondrial integrity by either antimycin A or peroxisome proliferator-activated receptor-γ coactivator-1α small-interfering RNA significantly increased the number of total, and activated, released endothelial microparticles, and shear stress restored these back to basal levels. Collectively, these data demonstrate a critical role of endothelial mitochondrial integrity in preserving endothelial homeostasis. Moreover, prolonged laminar shear stress, which is systemically elevated during aerobic exercise in the vessel wall, mitigates endothelial dysfunction by promoting

Change regularity of water quality parameters in leakage flow conditions and their relationship with iron release.

Science.gov (United States)

Liu, Jingqing; Shentu, Huabin; Chen, Huanyu; Ye, Ping; Xu, Bing; Zhang, Yifu; Bastani, Hamid; Peng, Hongxi; Chen, Lei; Zhang, Tuqiao

2017-11-01

The long-term stagnation in metal water supply pipes, usually caused by intermittent consumption patterns, will cause significant iron release and water quality deterioration, especially at the terminus of pipelines. Another common phenomenon at the terminus of pipelines is leakage, which is considered helpful by allowing seepage of low-quality drinking water resulting from long-term stagnation. In this study, the effect of laminar flow on alleviating water quality deterioration under different leakage conditions was investigated, and the potential thresholds of the flow rate, which can affect the iron release process, were discussed. Based on a galvanized pipe and ductile cast iron pipe pilot platform, which was established at the terminus of pipelines, this research was carried out by setting a series of leakage rate gradients to analyze the influence of different leakage flow rates on iron release, as well as the relationship with chemical and biological parameters. The results showed that the water quality parameters were obviously influenced by the change in flow velocity. Water quality was gradually improved with an increase in flow velocity, but its change regularity reflected a diversity under different flow rates (p water distribution system, when the bulk water was at the critical laminar flow velocity, the concentration of total iron, the quantity and rate of total iron release remain relatively in an ideal and safe situation. Copyright © 2017. Published by Elsevier Ltd.

In vitro effect of Δ9-tetrahydrocannabinol to stimulate somatostatin release and block that of luteinizing hormone-releasing hormone by suppression of the release of prostaglandin E2

International Nuclear Information System (INIS)

Rettori, V.; Aguila, M.C.; McCann, S.M.; Gimeno, M.F.; Franchi, A.M.

1990-01-01

Previous in vivo studies have shown that Δ 9 -tetrahydrocannabinol (THC), the principal active ingredient in marijuana, can suppress both luteinizing hormone (LH) and growth hormone (GH) secretion after its injection into the third ventricle of conscious male rats. The present studies were deigned to determine the mechanism of these effects. Various doses of THC were incubated with either stalk median eminence fragments (MEs) or mediobasal hypothalamic (MBH) fragments in vitro. Although THC (10 nM) did not alter basal release of LH-releasing hormone (LHRH) from MEs in vitro, it completely blocked the stimulatory action of dopamine or nonrepinephrine on LHRH release. The effective doses to block LHRH release were associated with a blockade of synthesis and release of prostaglandin E 2 (PGE 2 ) from MBH in vitro. In contrast to the suppressive effect of THC on LHRH release, somatostatin release from MEs was enhanced in a dose-related manner with a minimal effective dose of 1 nM. Since PGE 2 suppresses somatostatin release, this enhancement may also be related to the suppressive effect of THC on PGE 2 synthesis and release. The authors speculate that these actions are mediated by the recently discovered THC receptors in the tissue. The results indicate that the suppressive effect of THC on LH release is mediated by a blockade of LHRH release, whereas the suppressive effect of the compound on growth hormone release is mediated, at least in part, by a stimulation of somatostatin release

Antibacterial activity and ion release of bonding agent containing amorphous calcium phosphate nanoparticles.

Science.gov (United States)

Chen, Chen; Weir, Michael D; Cheng, Lei; Lin, Nancy J; Lin-Gibson, Sheng; Chow, Laurence C; Zhou, Xuedong; Xu, Hockin H K

2014-08-01

Recurrent caries at the margins is a primary reason for restoration failure. The objectives of this study were to develop bonding agent with the double benefits of antibacterial and remineralizing capabilities, to investigate the effects of NACP filler level and solution pH on Ca and P ion release from adhesive, and to examine the antibacterial and dentin bond properties. Nanoparticles of amorphous calcium phosphate (NACP) and a quaternary ammonium monomer (dimethylaminododecyl methacrylate, DMADDM) were synthesized. Scotchbond Multi-Purpose (SBMP) primer and adhesive served as control. DMADDM was incorporated into primer and adhesive at 5% by mass. NACP was incorporated into adhesive at filler mass fractions of 10%, 20%, 30% and 40%. A dental plaque microcosm biofilm model was used to test the antibacterial bonding agents. Calcium (Ca) and phosphate (P) ion releases from the cured adhesive samples were measured vs. filler level and solution pH of 7, 5.5 and 4. Adding 5% DMADDM and 10-40% NACP into bonding agent, and water-aging for 28 days, did not affect dentin bond strength, compared to SBMP control at 1 day (p>0.1). Adding DMADDM into bonding agent substantially decreased the biofilm metabolic activity and lactic acid production. Total microorganisms, total streptococci, and mutans streptococci were greatly reduced for bonding agents containing DMADDM. Increasing NACP filler level from 10% to 40% in adhesive increased the Ca and P ion release by an order of magnitude. Decreasing solution pH from 7 to 4 increased the ion release from adhesive by 6-10 folds. Bonding agents containing antibacterial DMADDM and remineralizer NACP were formulated to have Ca and P ion release, which increased with NACP filler level from 10% to 40% in adhesive. NACP adhesive was "smart" and dramatically increased the ion release at cariogenic pH 4, when these ions would be most-needed to inhibit caries. Therefore, bonding agent containing DMADDM and NACP may be promising to inhibit

Thermal treating of acrylic matrices as a tool for controlling drug release.

Science.gov (United States)

Hasanzadeh, Davood; Ghaffari, Solmaz; Monajjemzadeh, Farnaz; Al-Hallak, M H D-Kamal; Soltani, Ghazal; Azarmi, Shirzad

2009-12-01

The purpose of the present study was to investigate the effect of thermal-treating on the release of ibuprofen from the granules prepared using aqueous dispersions of Eudragit. To accomplish this goal, different formulations were prepared using wet granulation method containing two different types of Eudragit aqueous dispersions, RS30D, RL30D and Avicel as filler. Tablets were prepared using direct compression method. The prepared tablets were thermally treated at 50 and 70 degrees C for 24 h. The drug release from tablets was assessed before and after thermal-treating. The results of release study showed that, thermally-treating the tablets at the temperatures higher than glass transition temperature (Tg) of the polymer can decrease the drug release from matrices. For mechanistic evaluation of the effect of thermal-treating, powder X-ray diffraction (XPD), scanning electron microscopy (SEM), differential scanning calorimeter (DSC), Fourier transform infrared (FT-IR) and helium pycnometer have been employed. The SEM graphs showed that the tablets have smoother surface with less porosity after thermal-treating. FT-IR spectra showed no change in the spectrum of thermally-treated tablet compared to control. In DSC graphs, no crystalline change was seen in the heat-treated samples of ibuprofen tablets, but decreased and widened peak size were related to the probable formation of solid solution of ibuprofen in Eudragit matrix. The results of helium pycnometer showed a significant decrease in the total porosity of some heat-treated samples. This study revealed the importance of thermal treating on the drug release from sustained release tablets containing Eudragit polymer.

A trap, neuter, and release program for feral cats on Prince Edward Island

Science.gov (United States)

Gibson, Karen L.; Keizer, Karen; Golding, Christine

2002-01-01

A new program to address the feral cat population on Prince Edward Island was undertaken during the spring and summer of 2001. Feral cats from specific geographic areas were trapped, sedated, and tested for feline leukemia virus and feline immunodeficiency virus. Healthy cats were neutered, dewormed, vaccinated, tattooed, and released to their area of origin. A total of 185 cats and kittens were trapped and tested during a 14-week period; 158 cats and kittens as young as 6 weeks of age were neutered and released. Twenty-three adult cats were positive for feline leukemia virus, feline immunodeficiency virus, or both, and were euthanized. PMID:12240526

Toxics Release Inventory (TRI)

Data.gov (United States)

U.S. Environmental Protection Agency — The Toxics Release Inventory (TRI) is a dataset compiled by the U.S. Environmental Protection Agency (EPA). It contains information on the release and waste...

Nitrogen and phosphorus release from organic wastes and suitability as bio-based fertilizers in a circular economy

DEFF Research Database (Denmark)

Case, Sean; Jensen, Lars Stoumann

2018-01-01

The drive to a more circular economy has created increasing interest in recycling organic wastes as bio-based fertilizers. This study screened 15 different manures, digestates, sludges, composts, industry by-products, and struvites. Nitrogen (N) and phosphorous (P) release was compared following...... of the material (r = −0.6). Composted, dried, or raw organic waste materials released less N (mean of 10.8 ± 0.5%, 45.3 ± 7.2%, and 47.4 ± 3.2% of total N added respectively) than digestates, industry-derived organic fertilizer products, and struvites (mean of 58.2 ± 2.8%, 77.7 ± 6.0%, and 100.0 ± 13.1% of total...

Sustained release of radioprotective agents

International Nuclear Information System (INIS)

Shani, J.

1980-11-01

New pharmaceutical formulations for the sustained release into the G.I. tract of radioprotective agents have been developed by the authors. The experimental method initially consisted in the production of methylcellulose microcapsules. This method failed apparently because of the premature ''explosion'' of the microcapsules and the consequent premature release of massive amounts of the drug. A new method has been developed which consists in drying and pulverising cysteamine and cysteine preparations, mixing them in various proportions with stearic acid and ethylcellulose as carriers. The mixture is then compressed into cylindrical tablets at several pressure values and the leaching rate of the radioprotective agents is then measured by spectrophotometry. The relation between the concentration of the active drug and its rate of release, and the effect on the release rate of the pressure applied to the tablet during its formation were also investigated. Results indicating that the release rate was linearly related to the square root of ''t'' seem to be in agreement with what is predictable, according to Higuchi's equation, save for the very initial and terminal phases. A clear correlation was also established between the stearic acid/ethylcellulose ratios and the release of 20% cysteine, namely a marked decrease in the rate of cysteine release was observed with increasing concentrations of stearic acid. Finally, it was observed that a higher formation pressure results in quicker release of the drug

1997 toxic chemical release inventory. Emergency Planning and Community Right-To-Know Act, Section 313

International Nuclear Information System (INIS)

Zaloudek, D.E.

1998-01-01

Two listed toxic chemicals were used at the Hanford Site above established activity thresholds: phosphoric acid and chlorine. Because total combined quantities of chlorine released, disposed, treated, recovered through recycle operations, co-combusted for energy recovery, and transferred to off-site locations for the purpose of recycle, energy recovery, treatment, and/or disposal, amounted to less than 500 pounds, the Hanford Site qualified for the alternate one million pound threshold for chlorine. Accordingly, this Toxic Chemical Release Inventory includes a Form A for chlorine, and a Form B for phosphoric acid

Release of Antioxidant Capacity from Five Plant Foods during a Multistep Enzymatic Digestion Protocol

NARCIS (Netherlands)

Papillo, V.A.; Vitaglione, P.; Graziani, G.; Gokmen, V.; Fogliano, V.

2014-01-01

This study aimed at elucidating the influence of food matrix on the release of antioxidant activity from five plant foods (apple, spinach, walnut, red bean, and whole wheat). To this purpose a protocol based on sequential enzymatic digestion was adopted. The total antioxidant capacity (TAC) of both

Fission-product release during accidents

International Nuclear Information System (INIS)

Hunt, C.E.L.; Cox, D.S.

1991-09-01

One of the aims when managing a reactor accident is to minimize the release of radioactive fission products. Release is dependent not only on the temperature, but also on the partial pressure of oxygen. Strongly oxidizing atmospheres, such as those that occurred during the Chernobyl accident, released semi-volatile elements like ruthenium, which has volatile oxides. At low temperatures, UO 2 oxidization to U 3 O 8 can result in extensive breakup of the fuel, resulting in the release of non-volatile fission products as aerosols. Under less oxidizing conditions, when hydrogen accumulates from the zirconium-water reaction, the resulting low oxygen partial pressure can significantly reduce these reactions. At TMI-2, only the noble gases and volatile fission products were released in significant quantities. A knowledge of the effect of atmosphere as well as temperature on the release of fission products from damaged reactor cores is therefore a useful, if not necessary, component of information required for accident management

RAVEN Beta Release

International Nuclear Information System (INIS)

Rabiti, Cristian; Alfonsi, Andrea; Cogliati, Joshua Joseph; Mandelli, Diego; Kinoshita, Robert Arthur; Wang, Congjian; Maljovec, Daniel Patrick; Talbot, Paul William

2016-01-01

This documents the release of the Risk Analysis Virtual Environment (RAVEN) code. A description of the RAVEN code is provided, and discussion of the release process for the M2LW-16IN0704045 milestone. The RAVEN code is a generic software framework to perform parametric and probabilistic analysis based on the response of complex system codes. RAVEN is capable of investigating the system response as well as the input space using Monte Carlo, Grid, or Latin Hyper Cube sampling schemes, but its strength is focused toward system feature discovery, such as limit surfaces, separating regions of the input space leading to system failure, using dynamic supervised learning techniques. RAVEN has now increased in maturity enough for the Beta 1.0 release.

RAVEN Beta Release

Energy Technology Data Exchange (ETDEWEB)

Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Alfonsi, Andrea [Idaho National Lab. (INL), Idaho Falls, ID (United States); Cogliati, Joshua Joseph [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mandelli, Diego [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kinoshita, Robert Arthur [Idaho National Lab. (INL), Idaho Falls, ID (United States); Wang, Congjian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Maljovec, Daniel Patrick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Talbot, Paul William [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-02-01

This documents the release of the Risk Analysis Virtual Environment (RAVEN) code. A description of the RAVEN code is provided, and discussion of the release process for the M2LW-16IN0704045 milestone. The RAVEN code is a generic software framework to perform parametric and probabilistic analysis based on the response of complex system codes. RAVEN is capable of investigating the system response as well as the input space using Monte Carlo, Grid, or Latin Hyper Cube sampling schemes, but its strength is focused toward system feature discovery, such as limit surfaces, separating regions of the input space leading to system failure, using dynamic supervised learning techniques. RAVEN has now increased in maturity enough for the Beta 1.0 release.

Decomposition and nutrient release of leguminous plants in coffee agroforestry systems

Directory of Open Access Journals (Sweden)

Eduardo da Silva Matos

2011-02-01

Full Text Available Leguminous plants used as green manure are an important nutrient source for coffee plantations, especially for soils with low nutrient levels. Field experiments were conducted in the Zona da Mata of Minas Gerais State, Brazil to evaluate the decomposition and nutrient release rates of four leguminous species used as green manures (Arachis pintoi, Calopogonium mucunoides, Stizolobium aterrimum and Stylosanthes guianensis in a coffee agroforestry system under two different climate conditions. The initial N contents in plant residues varied from 25.7 to 37.0 g kg-1 and P from 2.4 to 3.0 g kg-1. The lignin/N, lignin/polyphenol and (lignin+polyphenol/N ratios were low in all residues studied. Mass loss rates were highest in the first 15 days, when 25 % of the residues were decomposed. From 15 to 30 days, the decomposition rate decreased on both farms. On the farm in Pedra Dourada (PD, the decomposition constant k increased in the order C. mucunoides < S. aterrimum < S. guianensis < A. pintoi. On the farm in Araponga (ARA, there was no difference in the decomposition rate among leguminous plants. The N release rates varied from 0.0036 to 0.0096 d-1. Around 32 % of the total N content in the plant material was released in the first 15 days. In ARA, the N concentration in the S. aterrimum residues was always significantly higher than in the other residues. At the end of 360 days, the N released was 78 % in ARA and 89 % in PD of the initial content. Phosphorus was the most rapidly released nutrient (k values from 0.0165 to 0.0394 d-1. Residue decomposition and nutrient release did not correlate with initial residue chemistry and biochemistry, but differences in climatic conditions between the two study sites modified the decomposition rate constants.

Alkali Release from Typical Danish Aggregates to Potential ASR Reactive Concrete

DEFF Research Database (Denmark)

Thomsen, Hans Christian Brolin; Grelk, Bent; Barbosa, Ricardo Antonio

Alkali-silica reaction (ASR) in concrete is a well-known deterioration mechanism affecting the long term durability of Danish concrete structures. Deleterious ASR cracking can be significantly reduced or prevented by limiting the total alkali content of concrete under a certain threshold limit......, which in Denmark is recommended to 3 kg/m3 Na2Oeq.. However, this threshold limit does not account for the possible internal contribution of alkali to the concrete pore solution by release from aggregates or external contributions from varies sources. This study indicates that certain Danish aggregates...... are capable of releasing more than 0.46 kg/m3 Na2Oeq. at 13 weeks of exposure in laboratory test which may increase the risk for deleterious cracking due to an increase in alkali content in the concrete....

The in Vitro Release of Indomethacin from Suppositories: Effects of Bases and Comparison of Different Dissolution Methods.

Science.gov (United States)

Mori, Kenji; Hori, Seiichi; Kawata, Tsubasa; Kogure, Sanae; Matsumoto, Kaori; Hasegawa, Tetsuya; Akimoto, Masayuki

2017-01-01

The suitability of apparatuses for the quality control of indomethacin (IND, 50 mg) compounded suppositories was evaluated and the effects of the type of suppository base on release profiles was investigated. The release characteristics of hydrophilic and lipophilic suppositories containing IND were compared using four types of dissolution methods: basket (RB), paddle (PD), dialysis tubing (DT) and flow-through cell (FTC). The release process was evaluated using the following model independent parameters: the mean dissolution time (MDT), cumulative percent of drug released (Q) at the end of the sampling time, and dissolution efficiency (DE). The fastest and most reproducible release profiles were observed for a hydrophilic base (macrogols), which resulted in more than 90% of the drug being released in 30 min using PD, RB and FTC. After 90 min, 90% of the total amount of the drug was released from a mixture of hydrophilic bases with a lipophilic base (macrogols and hard fat) in compendial dissolution methods and the mixture base was the second fastest only to the hydrophilic base. The slowest release profiles in each method were observed for the lipophilic base (hard fat). Poor drug release from any type of suppository base was noted using DT. Based on the results of the present study, FTC may be regarded as an adequate technique allowing sufficient discriminating power for the quality control of IND compounded suppositories.

Fight and air exposure times of caught and released salmonids from the South Fork Snake River

Science.gov (United States)

Roth, Curtis J.; Schill, Daniel J.; Quist, Michael C.

2018-01-01

Catch-and-release regulations are among the most common types of fishing regulations. In recent years, concerns have arisen regarding the exposure of fish to air during catch-and-release angling. The purpose of our study was to quantify the length of time angled fish were exposed to air by anglers in a typical catch-and-release fishery and relate it to the lengths of time reported to produce negative effects. In total, 312 individual anglers were observed on the South Fork Snake River, Idaho, from May through August 2016. Fight time varied from 1.1 s to 230.0 s, and average fight time was 40.0 s (SD = 36.8). Total air exposure times varied from 0.0 s to 91.8 s and averaged 19.3 s (SD = 15.0). Though not statistically significant, a trend in reduced fight times was observed when anglers were guided and increased air exposure times when a net was used and a picture was taken. Results of the current study suggest that anglers expose fish to air for periods that are much less than those reported to cause mortality.

Release-ability of nano fillers from different nanomaterials (toward the acceptability of nanoproduct)

International Nuclear Information System (INIS)

Golanski, L.; Guiot, A.; Pras, M.; Malarde, M.; Tardif, F.

2012-01-01

It is of great interest to set up a reproducible and sensitive method able to qualify nanomaterials before their market introduction in terms of their constitutive nanoparticle release-ability in usage. Abrasion was performed on polycarbonate, epoxy, and PA11 polymers containing carbone nanotubes (CNT) up to 4 %wt. Using Taber linear standard tool and standard abrasion conditions no release from polymer coatings containing CNT was measured. In this study, new practical tools inducing non-standardized stresses able to compete with van der Waals forces were developed and tested on model polymers, showing controlled CNT dispersion. These stresses are still realistic, corresponding to scratching, instantaneous mechanical shocks, and abrasion of the surface. They offer an efficient way to quantify if release is possible from nanomaterials under different mechanical stresses and therefore give an idea about the mechanisms that favors it. Release under mechanical shocks and hard abrasion was obtained using these tools but only when nanomaterials present a bad dispersion of CNT within the epoxy matrix. Under the same conditions no release was obtained from the same material presenting a good dispersion. The CNT used in this study showed an external diameter Dext = 12 nm, an internal diameter Din = 5 nm, and a mean length of 1 μm. Release from paints under hard abrasion using a standard rotative Taber tool was obtained from a intentionaly non-optimized paint containing SiO 2 nanoparticles up to 35 %wt. The primary diameter of the SiO 2 was estimated to be around 12 nm. A metallic rake was efficient to remove nanoparticles from a non-woven fabric nanomaterial.

Total Androgen Blockade Versus a Luteinizing Hormone-Releasing Hormone Agonist Alone in Men With High-Risk Prostate Cancer Treated With Radiotherapy

International Nuclear Information System (INIS)

Nanda, Akash; Chen, M.-H.; Moran, Brian J.; Braccioforte, Michelle H.; Dosoretz, Daniel; Salenius, Sharon; Katin, Michael; Ross, Rudi; D'Amico, Anthony V.

2010-01-01

Purpose: To assess whether short-course total androgen blockade vs. a luteinizing hormone-releasing hormone (LHRH) agonist alone affects the risk of prostate cancer-specific mortality (PCSM) in men with localized but high-risk disease treated with radiotherapy. Methods and Materials: The study cohort comprised 628 men with T1-T4, N0, M0 prostate cancer with high-risk disease (prostate-specific antigen level >20 ng/mL, Gleason score ≥8, or clinical category ≥T3) treated with 45 Gy of external beam radiotherapy followed by a brachytherapy boost in addition to receiving a median of 4.3 (interquartile range [IQR], 3.6-6.4) months of hormonal blockade with an LHRH agonist plus an antiandrogen or monotherapy with an LHRH agonist. Fine and Gray's multivariable regression analysis was used to determine whether combination androgen suppression therapy (AST) vs. monotherapy affected the risk of PCSM, adjusting for treatment year, duration of AST, age, and known prognostic factors. Results: After a median follow-up of 4.9 (IQR, 3.5-6.5) years, men receiving combination AST had a lower risk of PCSM than those treated with monotherapy (adjusted hazard ratio [AHR], 0.18; 95% confidence interval [CI], 0.04-0.90; p = 0.04). An increasing prostate-specific antigen level (AHR, 2.70; 95% CI, 1.64-4.45; p < 0.001) and clinical category T3/4 disease (AHR, 29.6; 95% CI, 2.88-303.5; p = 0.004) were also associated with an increased risk of PCSM. Conclusions: In men with localized but high-risk prostate cancer treated with external beam radiotherapy and brachytherapy, short-course AST with an LHRH agonist plus an antiandrogen is associated with a decreased risk of PCSM when compared with monotherapy with an LHRH agonist.

Modelling vesicular release at hippocampal synapses.

Directory of Open Access Journals (Sweden)

Suhita Nadkarni

2010-11-01

Full Text Available We study local calcium dynamics leading to a vesicle fusion in a stochastic, and spatially explicit, biophysical model of the CA3-CA1 presynaptic bouton. The kinetic model for vesicle release has two calcium sensors, a sensor for fast synchronous release that lasts a few tens of milliseconds and a separate sensor for slow asynchronous release that lasts a few hundred milliseconds. A wide range of data can be accounted for consistently only when a refractory period lasting a few milliseconds between releases is included. The inclusion of a second sensor for asynchronous release with a slow unbinding site, and thereby a long memory, affects short-term plasticity by facilitating release. Our simulations also reveal a third time scale of vesicle release that is correlated with the stimulus and is distinct from the fast and the slow releases. In these detailed Monte Carlo simulations all three time scales of vesicle release are insensitive to the spatial details of the synaptic ultrastructure. Furthermore, our simulations allow us to identify features of synaptic transmission that are universal and those that are modulated by structure.

Assessment of the Potential Release of Radioactivity from Installations at AERE, Harwell. Implications for Emergency Planning

Energy Technology Data Exchange (ETDEWEB)

Flew, Elizabeth M.; Lister, B. A.J. [Atomic Energy Research Establishment, Harwell, Didcot, Berks. (United Kingdom)

1969-10-15

As part of a review of the site emergency organization at AERE, a realistic reappraisal has been made of the potential hazard to the establishment and district of all the buildings containing significant amounts of radioactive materials. To assess the amount of radioactive material which might be released under specified accident conditions, four factors have been applied to the total building stock: (a) the fraction of the stock involved, (b) the percentage conversion to an aerosol form, (c) release from primary containment and (d) release from the building. These potential release figures have been compared with ''site hazardous release'' figures for relevant radionuclides i.e., amounts which could give rise to exposure above defined reference levels. Those buildings with more than one tenth of the potential for causing; a site or district hazard have been designated ''risk buildings''. Such a quantitative assessment, although necessarily very approximate, has been of considerable value in determining the type and complexity of the central emergency organization required and in producing the right emphasis on exercises, training, liaison with outside bodies, etc. (author)

AIR POLLUTION FROM ANIMAL AND MUNICIPAL WASTEWATER: ASSESSMENT OF PRODUCTION AND RELEASE OF NOXIOUS GASES

DEFF Research Database (Denmark)

Dai, Xiaorong

from animal manure (mixture of urine and feces) by hydrolysis of urinary urea catalyzed by microbial urease present in feces. To better understand the enzymatic process of ammonia formation in manure, experiments based on Michaelis-Menten kinetics were conducted to obtain accurate estimates...... of the kinetic parameters of urease activity of feces and manure from pig and cattle, and to investigate the effects of pH on animal fecal urease by individual ammonium generation rate determination at five pH levels. Investigating the gas production and release mechanisms is important not only for estimating...... characteristics of different types of wastes (e.g., the total nitrogen, total ammoniacal nitrogen, dry matter, and pH) had great influence on the releases of NH3, CO2, H2S, and SO2. The investigation of kinetic parameter showed that the maximum urease activity for pig feces is at around pH 7, while...

Airborne Release of Particles in Overheating Incidents Involving Plutonium Metal and Compounds

Energy Technology Data Exchange (ETDEWEB)

Schwendiman, L. C.; Mishima, J.; Radasch, C. A. [Battelle Memorial Institute, Pacific Northwest Laboratory, Richland, WA (United States)

1968-12-15

Ever-increasing utilization of nuclear fuels will result in wide-scale plutonium recovery processing, reconstitution of fuels, transportation, and extensive handling of this material. A variety of circumstances resulting in overheating and fires involving plutonium may occur, releasing airborne particles. This work describes the observations from a study in which the airborne release of plutonium and its compounds was measured during an exposure of the material of interest containing plutonium to temperatures which may result from fires. Aerosol released from small cylinders of metallic plutonium ignited in air at temperatures from 410 to 650 Degree-Sign C ranged from 3 x 10{sup -6} to 5 x 10{sup -5} wt%. Particles smaller than 15{mu}m in diameter represented as much as 0.03% of the total released. Large plutonium pieces weighing from 456 to 1770 g were ignited and allowed to oxidize completely in air with a velocity of around 500 cm/sec. Release rates of from 0.0045 to 0.032 wt% per hour were found. The median mass diameter of airborne material was 4 {mu}m. Quenching the oxidation with magnesium oxide sand reduced the release to 2.9 X 10{sup -4} wt% per hour. Many experiments were carried out in which plutonium compounds as powders were heated at temperatures ranging from 700 to 1000 Degree-Sign C with several air flows. Release rates ranged from 5 x 10{sup -8} to 0.9 wt% per hour, depending upon the compound and the conditions imposed. The airborne release from boiling solutions of plutonium nitrate were roughly related to energy of boiling, and ranged from 4 x 10{sup -4} to 2 x 10{sup -1} % for the evaporation of 90% of the solution. The fraction airborne when combustibles contaminated with plutonium are burned is under study. The data reported can be used in assessing the consequences of off-standard situations involving plutonium and its compounds in fires. (author)

Decapeptides as effective agonists from L-amino acids biologically equivalent to the luteinizing hormone-releasing hormone

International Nuclear Information System (INIS)

Folkers, K.; Bowers, C.Y.; Tang, P.L.; Kubota, M.

1986-01-01

Apparently, no agonist has been found that is comparable in potency to the luteinizing hormone-releasing hormone (LHRH) for release of LH and follicle-stimulating hormone (FSH) without substitutions with unnatural or D forms of natural amino acids. Of 139 known agonist analogs of LHRH, two were active in the range of 65%. The four LHRHs known to occur in nature involve a total of six amino acids (Tyr, His, Leu, Trp, Arg, Gln) in positions 5, 7, and 8. There are 16 possible peptides with these six amino acids in positions 5, 7, and 8, of which 4 are the known LHRHs, and 2 more were synthesized. The authors have synthesized the 10 new peptides and assayed 11 in vivo and in vitro, and they found not only 1 but a total of 5 that have activity equivalent to or greater than that of LHRH for the release of LH and/or FSH under at least one assay condition. These five are as follows: [His 5 ,Trp 7 ,Gln 8 ]LHRH; [His 5 ,Trp 7 ,Leu 8 ]LHRH; [His 5 ,Trp 7 ]LHRH; [Trp 7 ]LHRH; [His 5 ]LHRH. These structures are a basis for the design of antagonists without Arg 8 toward avoiding histamine release. Complete inhibition of LH and FSH release in vivo may be induced by joint use of Arg 8 and Gln 8 or Leu 8 antagonists. These potent agonists, related to LHRH, may be therapeutically useful in disorders of reproduction, the central nervous system, and for the control of hormone-dependent carcinomas. Radioreceptor assays and radioimmunoassays were utilized

28 CFR 2.83 - Release planning.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Release planning. 2.83 Section 2.83... Release planning. (a) All grants of parole shall be conditioned on the development of a suitable release... parole date for purposes of release planning for up to 120 days without a hearing. If efforts to...

Population dose commitments due to radioactive releases from nuclear power plant sites in 1982. Volume 4

International Nuclear Information System (INIS)

Baker, D.A.; Peloquin, R.A.

1986-06-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1982. Fifty-year dose commitments from a one-year exposure were calculated from both liquid and atmospheric releases for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 51 sites. This report tabulates the results of these calculations, showing the dose commitments for both liquid and airborne pathways for each age group and organ. Also included for each site is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total dose commitments from both liquid and airborne pathways ranged from a high of 30 person-rem to a low of 0.007 person-rem for the sites with plants operating throughout the year with an arithmetic mean of 3 person-rem. The total population dose for all sites was estimated at 130 person-rem for the 100 million people considered at risk. The average individual dose commitment from all pathways on a site basis ranged from a low of 6 x 10 -7 mrem to a high of 0.06 mrem. No attempt was made in this study to determine the maximum dose commitment received by any one individual from the radionuclides released at any of the sites

Toxic releases from power plants

International Nuclear Information System (INIS)

Rubin, E.S.

1999-01-01

Beginning in 1998, electric power plants burning coal or oil must estimate and report their annual releases of toxic chemicals listed in the Toxics Release Inventory (TRI) published by the US Environmental Protection Agency (EPA). This paper identifies the toxic chemicals of greatest significance for the electric utility sector and develops quantitative estimates of the toxic releases reportable to the TRI for a representative coal-fired power plant. Key factors affecting the magnitude and types of toxic releases for individual power plants also are discussed. A national projection suggests that the magnitude of electric utility industry releases will surpass those of the manufacturing industries which current report to the TRI. Risk communication activities at the community level will be essential to interpret and provide context for the new TRI results

Examination of Conservatism in Ground-level Source Release Assumption when Performing Consequence Analysis

Energy Technology Data Exchange (ETDEWEB)

Kim, Sung-yeop; Lim, Ho-Gon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

One of these assumptions frequently assumed is the assumption of ground-level source release. The user manual of a consequence analysis software HotSpot is mentioning like below: 'If you cannot estimate or calculate the effective release height, the actual physical release height (height of the stack) or zero for ground-level release should be used. This will usually yield a conservative estimate, (i.e., larger radiation doses for all downwind receptors, etc).' This recommendation could be agreed in aspect of conservatism but quantitative examination of the effect of this assumption to the result of consequence analysis is necessary. The source terms of Fukushima Dai-ichi NPP accident have been estimated by several studies using inverse modeling and one of the biggest sources of the difference between the results of these studies was different effective source release height assumed by each studies. It supports the importance of the quantitative examination of the influence by release height. Sensitivity analysis of the effective release height of radioactive sources was performed and the influence to the total effective dose was quantitatively examined in this study. Above 20% difference is maintained even at longer distances, when we compare the dose between the result assuming ground-level release and the results assuming other effective plume height. It means that we cannot ignore the influence of ground-level source assumption to the latent cancer fatality estimations. In addition, the assumption of ground-level release fundamentally prevents detailed analysis including diffusion of plume from effective plume height to the ground even though the influence of it is relatively lower in longer distance. When we additionally consider the influence of surface roughness, situations could be more serious. The ground level dose could be highly over-estimated in short downwind distance at the NPP sites which have low surface roughness such as Barakah site in

Population dose commitments due to radioactive releases from nuclear power plant sites in 1988

International Nuclear Information System (INIS)

Baker, D.A.

1992-01-01

Population radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1988. Fifty-year commitments for a one-year exposure from both liquid and atmospheric releases were calculated for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 71 reactor sites. This report tabulates the results of these calculations, showing the dose commitments for both water and airborne pathways for each age group and organ. Also included for each of the sites is a histogram showing the fraction of the total population within 2 to 80 km around each site receiving various average dose commitments from the airborne pathways. The total collective dose commitments (from both liquid and airborne pathways) for each site ranged from a high of 16 person-rem to a low of 0.0011 person-rem for the sites with plants operating throughout the year with an arithmetic mean of 1.1 person-rem. The total population dose for all sites was estimated at 75 person-rem for the 150 million people considered at risk. The site average individual dose commitment from all pathways ranged from a low of 3 x 10 -7 mrem to a high of 0.02 mrem. No attempt was made in this study to determine the maximum dose commitment received by any one individual from the radionuclides released at any of the sites. However, licensee calculation of doses to the maximally exposed individual at some sites indicated values of up to approximately 100 times average individual doses (on the order of a few millirem per year)

Predicted radionuclide release from reactor-related unenclosed solid objects dumped in the Sea of Japan and the Pacific Ocean, east coast of Kamchatka

International Nuclear Information System (INIS)

Mount, M.E.; Lynn, N.M.; Warden, J.M.

1996-06-01

Between 1978 and 1991 reactor-related solid radioactive waste was dumped by the former Soviet Union as unenclosed objects in the Pacific Ocean, east coast of Kamchatka, and the Sea of Japan. This paper presented estimates for the current (1994) inventory of activation and corrosion products contained in the reactor-related unenclosed solid objects. In addition, simple models derived for prediction of radionuclide release from marine reactors dumped in the Kara Sea are applied to certain of the dumped objects to provide estimates of radionuclide release to the Pacific Ocean, east coast of Kamchatka, and Sea of Japan environments. For the Pacific Ocean, east coast of Kamchatka, total release rates start below 0.01 GBq yr -1 and over 1,000 years, fall to 100 Bq yr -1 . In the Sea of Japan, the total release rate starts just above 1 GBq yr - 1 , dropping off to a level less than 0.1 GBq yr -1 , extending past the year 4,000

Nickel and cobalt release from children's toys purchased in Denmark and the United States.

Science.gov (United States)

Jensen, Peter; Hamann, Dathan; Hamann, Carsten R; Jellesen, Morten S; Jacob, Sharon E; Thyssen, Jacob P

2014-01-01

Nickel is the most common allergen detected by patch testing in children. There is an increasing number of cases in children who have not had exposure to piercing. Although the clinical relevance of nickel patch test reactions in children is sometimes uncertain, continued vigilance to identify new sources of nickel exposure in this age group is important. Recent case reports have described allergic nickel contact dermatitis in children following exposure to toys, but the magnitude of this problem is unknown. The aim of this study was to evaluate nickel and cobalt release from children's toys. We purchased 212 toys in 18 different retail and online stores in the United States and Denmark. Nickel and cobalt release was tested using the dimethylglyoxime and cobalt screening spot tests. A total of 73 toys (34.4%) released nickel, and none released cobalt. Toys are a commonly overlooked source of nickel exposure and sensitization. Therefore, dermatologists, allergists, and pediatricians should consider the role of toys in their evaluation of children with dermatitis, and the parents of children with positive nickel patch test reactions should be told that toys may release nickel and be a potential chemical source in the manifestation of allergic contact dermatitis.

Controlled drug release on amine functionalized spherical MCM-41

Energy Technology Data Exchange (ETDEWEB)

Szegedi, Agnes, E-mail: szegedi@chemres.hu [Institute of Materials and Environmental Chemistry, Research Centre for Natural Sciences, Hungarian Academy of Sciences, 1025 Budapest, Pusztaszeri ut 59-67 (Hungary); Popova, Margarita; Goshev, Ivan [Institute of Organic Chemistry with Centre of Phytochemistry, Bulgarian Academy of Sciences, Sofia (Bulgaria); Klebert, Szilvia [Institute of Materials and Environmental Chemistry, Research Centre for Natural Sciences, Hungarian Academy of Sciences, 1025 Budapest, Pusztaszeri ut 59-67 (Hungary); Mihaly, Judit [Institute of Molecular Pharmacology, Research Centre for Natural Sciences, Hungarian Academy of Sciences, 1025 Budapest, Pusztaszeri ut 59-67 (Hungary)

2012-10-15

MCM-41 silica with spherical morphology and small particle sizes (100 nm) was synthesized and modified by post-synthesis method with different amounts of 3-aminopropyltriethoxysilane (APTES). A comparative study of the adsorption and release of a model drug, ibuprofen, was carried out. The modified and drug loaded mesoporous materials were characterized by XRD, TEM, N{sub 2} physisorption, elemental analysis, thermal analysis and FT-IR spectroscopy. A new method was developed for the quantitative determination of amino groups in surface modified mesoporous materials by the ninhydrin reaction. Good correlation was found between the amino content of the MCM-41 materials determined by the ninhydrin method and their ibuprofen adsorption capacity. Amino modification resulted in high degree of ibuprofen loading and slow release rate in comparison to the parent non-modified MCM-41. - Graphical abstract: Determination of surface amino groups by ninhidrin method. Highlights: Black-Right-Pointing-Pointer Spherical MCM-41 modified by different amounts of APTES was studied. Black-Right-Pointing-Pointer Ibuprofen (IBU) adsorption and release characteristics was tested. Black-Right-Pointing-Pointer The ninhydrin reaction was used for the quantitative determination of amino groups. Black-Right-Pointing-Pointer Stoichiometric amount of APTES is enough for totally covering the surface with amino groups. Black-Right-Pointing-Pointer Good correlation was found between the amino content and IBU adsorption capacity.

Fluoride releasing and enamel demineralization around orthodontic brackets by fluoride-releasing composite containing nanoparticles.

Science.gov (United States)

Melo, Mary A S; Morais, Weslanny A; Passos, Vanara F; Lima, Juliana P M; Rodrigues, Lidiany K A

2014-05-01

Fluoride-containing materials have been suggested to control enamel demineralization around orthodontic brackets during the treatment with fixed appliances. The improvement of their properties has been made through innovations, such as the application of nanotechnology by incorporation of nanofillers. This in vitro study evaluated the capacity of fluoride releasing and enamel demineralization inhibition of fluoride-releasing nanofilled cement around orthodontic brackets using an artificial caries biofilm model. Forty bovine enamel discs were selected by evaluating surface microhardness and randomized into four groups (n = 10): non-fluoride-releasing microfilled composite, fluoride-releasing microfilled composite, resin-modified glass ionomer cement (RMGI), and fluoride-releasing nanofilled composite (FN). After brackets bonding in each disc, the specimens were subjected to a cariogenic challenge through a Streptococcus mutans biofilm model. After the experimental period, the biofilm formed around the brackets was collected for fluoride analysis and the mineral loss around the brackets was determined by integrated demineralization via cross-sectional microhardness measurement at 20 and 70 μm from the bracket margin. Additionally, samples of each group were subjected to energy-dispersive X-ray spectroscopy (EDX) analysis examined under a scanning electron microscopy (SEM). ANOVA followed by Tukey test were applied for fluoride concentration and mineral loss data, respectively. At both distances, only RMGI statistically differed from the other groups presenting the lowest demineralization, although there was a trend to a lower demineralization of enamel around brackets in FN group. Similar condition was found to fluoride concentration and EDX/SEM analysis. Under the cariogenic exposure condition of this study, the fluoride-releasing nanofilled material had similar performance to fluoride-releasing microfilled materials. The presence of nanofillers in the fluoride-releasing

Release of alpha emitters into the environment by Nuclear Industries of Brazil in Resende, RJ

International Nuclear Information System (INIS)

Pereira, Wagner S.; Kelecom, Alphonse; Santos, Rodney; Santos, Maisa F.M.; Torres, Vinicius R.M.; Rodrigues, Jéssica J.S.; Universidade Veiga de Almeida; Universidade Federal Fluminense

2017-01-01

The Nuclear Industries of Brazil operates in the field of nuclear energy and has a monopoly on mining and manufacturing the nuclear fuel element in Brazil. The Nuclear Fuel Factory is also responsible for the reconversion process, the manufacture of the pellets and the assembly of the fuel element. Once there is a possibility of particulate material generation during the reconversion processes and the manufacture of pellets, a method of collective protection of the worker was established, which includes a system of air exhaustion of the factory area, with the capacity to renew the indoor air six times per hour. As a control measure, there is a system of automatic detection of the release of radionuclides in the chimney that monitors and calculates the released values. Through the dose calculation model established by the National Commission for Nuclear Energy the release limit is fixed at 1.2∙ 10"7Bq.y"-"1 of alpha emitters by FCN. The present work aims to evaluate the alpha radionuclides released by FCN, in terms of total release (Bq) and Activity Concentration (AC, mBq∙m"-"3). In 2016 it was released 4.14∙10"6Bq.y"-"1, which means an average of 3.45∙10"5Bq.month"-"1. The largest mean for AC was 4.03 mBq∙m"-"3. The release data was almost an order of magnitude lower than the annual release limit, proving the suitability of the atmospheric effluents to the licensing requirements. The largest magnitudes of the two variables (AC and release) were observed in August while the smallest ones, in January. (author)

High-efficiency extracellular release of free fatty acids from Aspergillus oryzae using non-ionic surfactants.

Science.gov (United States)

Tamano, Koichi; Miura, Ai; Koike, Hideaki; Kamisaka, Yasushi; Umemura, Myco; Machida, Masayuki

2017-04-20

Free fatty acids (FFAs) are useful for generating biofuel compounds and functional lipids. Microbes are increasingly exploited to produce FFAs via metabolic engineering. However, in many microorganisms, FFAs accumulate in the cytosol, and disrupting cells to extract them is energy intensive. Thus, a simple cost-effective extraction technique must be developed to remove this drawback. We found that FFAs were released from cells of the filamentous fungus Aspergillus oryzae with high efficiency when they were cultured or incubated with non-ionic surfactants such as Triton X-100. The surfactants did not reduce hyphal growth, even at 5% (w/v). When the faaA disruptant was cultured with 1% Triton X-100, more than 80% of the FFAs synthesized de novo were released. When the disruptant cells grown without surfactants were incubated for 1h in 1% Triton X-100 solution, more than 50% of the FFAs synthesized de novo were also released. Other non-ionic surfactants in the same ether series, such as Brij 58, IGEPAL CA-630, and Tergitol NP-40, elicited a similar FFA release. The dry cell weight of total hyphae decreased when grown with 1% Triton X-100. The decrement was 4.9-fold greater than the weight of the released FFAs, implying release of other intracellular compounds. Analysis of the culture supernatant showed that intracellular lactate dehydrogenase was also released, suggesting that FFAs are not released by a specific transporter. Therefore, ether-type non-ionic surfactants probably cause non-specific release of FFAs and other intracellular compounds by increasing cell membrane permeability. Copyright © 2017 Elsevier B.V. All rights reserved.

Release of alpha emitters into the environment by Nuclear Industries of Brazil in Resende, RJ

Energy Technology Data Exchange (ETDEWEB)

Pereira, Wagner S.; Kelecom, Alphonse; Santos, Rodney; Santos, Maisa F.M.; Torres, Vinicius R.M.; Rodrigues, Jéssica J.S., E-mail: comap@inb.gov.br, E-mail: pereiraws@gmail.com, E-mail: lararapls@hotmail.com [Indústrias Nucleares do Brasil (COMAP.N/FCN/INB), Resende RJ (Brazil). Fábrica de Combustível Nuclear. Coordenação de Meio Ambiente e Proteção Radiológica Ambiental; Universidade Veiga de Almeida (UVA), Rio de Janeiro, RJ (Brazil); Universidade Federal Fluminense (LARARA-PLS/UFF), Niterói, RJ (Brazil). Laboratório de Radiobiologia e Radiometria

2017-07-01

The Nuclear Industries of Brazil operates in the field of nuclear energy and has a monopoly on mining and manufacturing the nuclear fuel element in Brazil. The Nuclear Fuel Factory is also responsible for the reconversion process, the manufacture of the pellets and the assembly of the fuel element. Once there is a possibility of particulate material generation during the reconversion processes and the manufacture of pellets, a method of collective protection of the worker was established, which includes a system of air exhaustion of the factory area, with the capacity to renew the indoor air six times per hour. As a control measure, there is a system of automatic detection of the release of radionuclides in the chimney that monitors and calculates the released values. Through the dose calculation model established by the National Commission for Nuclear Energy the release limit is fixed at 1.2∙ 10{sup 7}Bq.y{sup -1} of alpha emitters by FCN. The present work aims to evaluate the alpha radionuclides released by FCN, in terms of total release (Bq) and Activity Concentration (AC, mBq∙m{sup -3}). In 2016 it was released 4.14∙10{sup 6}Bq.y{sup -1}, which means an average of 3.45∙10{sup 5}Bq.month{sup -1}. The largest mean for AC was 4.03 mBq∙m{sup -3}. The release data was almost an order of magnitude lower than the annual release limit, proving the suitability of the atmospheric effluents to the licensing requirements. The largest magnitudes of the two variables (AC and release) were observed in August while the smallest ones, in January. (author)

Growth hormone (GH)-releasing activity of chicken GH-releasing hormone (GHRH) in chickens.

Science.gov (United States)

Harvey, S; Gineste, C; Gaylinn, B D

2014-08-01

Two peptides with sequence similarities to growth hormone releasing hormone (GHRH) have been identified by analysis of the chicken genome. One of these peptides, chicken (c) GHRH-LP (like peptide) was previously found to poorly bind to chicken pituitary membranes or to cloned and expressed chicken GHRH receptors and had little, if any, growth hormone (GH)-releasing activity in vivo or in vitro. In contrast, a second more recently discovered peptide, cGHRH, does bind to cloned and expressed cGHRH receptors and increases cAMP activity in transfected cells. The possibility that this peptide may have in vivo GH-releasing activity was therefore assessed. The intravenous (i.v.) administration of cGHRH to immature chickens, at doses of 3-100 μg/kg, significantly increased circulating GH concentrations within 10 min of injection and the plasma GH levels remained elevated for at least 30 min after the injection of maximally effective doses. The plasma GH responses to cGHRH were comparable with those induced by human (h) or porcine (p) GHRH preparations and to that induced by thyrotropin releasing hormone (TRH). In marked contrast, the i.v. injection of cGHRH-LP had no significant effect on circulating GH concentrations in immature chicks. GH release was also increased from slaughterhouse chicken pituitary glands perifused for 5 min with cGHRH at doses of 0.1 μg/ml or 1.0 μg/ml, comparable with GH responses to hGHRH1-44. In contrast, the perifusion of chicken pituitary glands with cGHRH-LP had no significant effect on GH release. In summary, these results demonstrate that cGHRH has GH-releasing activity in chickens and support the possibility that it is the endogenous ligand of the cGHRH receptor. Copyright © 2014 Elsevier Inc. All rights reserved.

Forecasting of future earthquakes in the northeast region of India considering energy released concept

Science.gov (United States)

Zarola, Amit; Sil, Arjun

2018-04-01

This study presents the forecasting of time and magnitude size of the next earthquake in the northeast India, using four probability distribution models (Gamma, Lognormal, Weibull and Log-logistic) considering updated earthquake catalog of magnitude Mw ≥ 6.0 that occurred from year 1737-2015 in the study area. On the basis of past seismicity of the region, two types of conditional probabilities have been estimated using their best fit model and respective model parameters. The first conditional probability is the probability of seismic energy (e × 1020 ergs), which is expected to release in the future earthquake, exceeding a certain level of seismic energy (E × 1020 ergs). And the second conditional probability is the probability of seismic energy (a × 1020 ergs/year), which is expected to release per year, exceeding a certain level of seismic energy per year (A × 1020 ergs/year). The logarithm likelihood functions (ln L) were also estimated for all four probability distribution models. A higher value of ln L suggests a better model and a lower value shows a worse model. The time of the future earthquake is forecasted by dividing the total seismic energy expected to release in the future earthquake with the total seismic energy expected to release per year. The epicentre of recently occurred 4 January 2016 Manipur earthquake (M 6.7), 13 April 2016 Myanmar earthquake (M 6.9) and the 24 August 2016 Myanmar earthquake (M 6.8) are located in zone Z.12, zone Z.16 and zone Z.15, respectively and that are the identified seismic source zones in the study area which show that the proposed techniques and models yield good forecasting accuracy.

Aging and temperature effects on DOC and elemental release from a metal contaminated soil

International Nuclear Information System (INIS)

Martinez, C.E.; Jacobson, A.R.; McBride, M.B.

2003-01-01

Increased aging and temperatures may affect DOC element complexes and their release. - The combined effect of time and temperature on elemental release and speciation from a metal contaminated soil (Master Old Site, MOS) was investigated. The soil was equilibrated at 10, 28, 45, 70 and 90 deg. C for 2 days, 2 weeks, and 2 months in the laboratory. Dissolved organic carbon (DOC), total soluble elements (by ICP), and labile metals (by DPASV) were determined in the filtered (0.22 μm) supernatants. For the samples equilibrated at 90 deg. C, DOC fractions were size fractionated by filtration and centrifugation; a subsample was only centrifuged while another was also filtered through a 0.45 μm filter. Analyses of the supernatants (ICP, DPASV, DOC) were performed on all size fraction subsamples. Dissolved organic carbon (DOC) increased both with temperature and incubation time; however, metal behavior was not as uniform. In general, total soluble metal release (ICP) paralleled the behavior of DOC, increasing with both time and temperature, and confirming the importance of soil organic matter (SOM) in metal retention. Voltammetric analysis (dpasv) of Cu and Zn showed that very little of these metals remains labile in solution due, presumably, to complexation with dissolved organic matter. Labile concentrations of Cd, on the other hand, constituted a significant portion (50%) of total soluble Cd. Copper and Al increased in solution with time (up to 2 months) and temperature up to 70 deg. C; however, at 90 deg. C the soluble concentration declined sharply. The same behavior was observed after equilibration for longer periods of time (550 days) at lower temperatures (23 and 70 deg. C). While concentrations of labile Cu and total soluble Cu and Al increased in the unfiltered samples, the trend remained the same. DPASV analysis showing shifts in labile Cu complexes with temperature and time, together with the results from the unfiltered samples, lead to the hypothesis that Cu

Underground water stress release models

Science.gov (United States)

Li, Yong; Dang, Shenjun; Lü, Shaochuan

2011-08-01

The accumulation of tectonic stress may cause earthquakes at some epochs. However, in most cases, it leads to crustal deformations. Underground water level is a sensitive indication of the crustal deformations. We incorporate the information of the underground water level into the stress release models (SRM), and obtain the underground water stress release model (USRM). We apply USRM to the earthquakes occurred at Tangshan region. The analysis shows that the underground water stress release model outperforms both Poisson model and stress release model. Monte Carlo simulation shows that the simulated seismicity by USRM is very close to the real seismicity.

Minthorn Springs Creek Summer Juvenile Release and Adult Collection Facility; 1994 Annual Report.

Energy Technology Data Exchange (ETDEWEB)

Rowan, Gerald D.

1995-05-01

The Confederated Tribes of the Umatilla Indian Reservation (CTUIR) and Oregon Department of Fish and Wildlife (ODFW) are cooperating in a joint effort to enhance steelhead and re-establish salmon runs in the Umatilla River Basin. Bonifer Pond, Minthorn Springs and Imeques C-mem-ini-kem acclimation facilities are operated for acclimation and release of juvenile summer steelhead (Oncorhynchus mykiss), fall and spring chinook salmon (O. tshawytscha) and coho salmon (O, kisutch). Minthorn is also used for holding and spawning summer steelhead, fall chinook and coho salmon. In the spring of 1994, juvenile summer steelhead were acclimated at Bonifer and Minthorn. At Imeques C-mem-ini-kem, juvenile spring chinook were acclimated in the spring and fall. A total of 92 unmarked and 42 marked summer steelhead were collected for broodstock at Three Mile Dam from October 1, 1993 through May 2, 1994 and held at Minthorn. An estimated 234,432 green eggs were taken from 48 females. The eggs were transferred to Irrigon Hatchery for incubation and early rearing. Fingerlings were transferred to Umatilla Hatchery for final rearing and release into the Umatilla River in 1995. Fall chinook and coho salmon broodstock were not collected in 1994. Coded-wire tag recovery information was accessed to determine the contribution of Umatilla River releases to ocean, Columbia River and Umatilla River fisheries. Total estimated juvenile adult survival rates are detailed in this document.

Analysis of in-pile tritium release experiments

International Nuclear Information System (INIS)

Kopasz, J.P.; Tam, S.W.; Johnson, C.E.

1992-01-01

The objective of this work is to characterize tritium release behavior from lithium ceramics and develop insight into the underlying tritium release mechanisms. Analysis of tritium release data from recent laboratory experiments with lithium aluminate has identified physical processes which were previously unaccounted for in tritium release models. A new model that incorporates the recent data and provides for release from multiple sites rather than only one site was developed. Calculations of tritium release using this model are in excellent agreement with the tritium release behavior reported for the MOZART experiment

Ultrasound enhanced release of therapeutics from drug-releasing implants based on titania nanotube arrays.

Science.gov (United States)

Aw, Moom Sinn; Losic, Dusan

2013-02-25

A non-invasive and external stimulus-driven local drug delivery system (DDS) based on titania nanotube (TNT) arrays loaded with drug encapsulated polymeric micelles as drug carriers and ultrasound generator is described. Ultrasound waves (USW) generated by a pulsating sonication probe (Sonotrode) in phosphate buffered saline (PBS) at pH 7.2 as the medium for transmitting pressure waves, were used to release drug-loaded nano-carriers from the TNT arrays. It was demonstrated that a very rapid release in pulsatile mode can be achieved, controlled by several parameters on the ultrasonic generator. This includes pulse length, time, amplitude and power intensity. By optimization of these parameters, an immediate drug-micelles release of 100% that spans a desirable time of 5-50 min was achieved. It was shown that stimulated release can be generated and reproduced at any time throughout the TNT-Ti implant life, suggesting considerable potential of this approach as a feasible and tunable ultrasound-mediated drug delivery system in situ via drug-releasing implants. It is expected that this concept can be translated from an in vitro to in vivo regime for therapeutic applications using drug-releasing implants in orthopedic and coronary stents. Crown Copyright © 2013. Published by Elsevier B.V. All rights reserved.

Multimicronutrient Slow-Release Fertilizer of Zinc, Iron, Manganese, and Copper

Directory of Open Access Journals (Sweden)

Siladitya Bandyopadhyay

2014-01-01

Full Text Available The process for the production of a slow-release micronutrient fertilizer is described. The compound contains zinc, iron, manganese, and copper as micronutrients and is produced by polymerizing a system containing phosphoric acid, zinc oxide, hematite, pyrolusite, copper sulfate, and magnesium oxide followed by neutralization of the polyphosphate chain with ammonium hydroxide. Changes in temperature, density, and viscosity of the reaction system during polymerization were studied. Reaction kinetics was studied at three different temperatures. Rate curves revealed a multistage process with essentially linear rates at each stage. Thus, each stage displayed zero order kinetics. The product was crystalline and revealed ordering of P-O-P chains. It had low solubility in water but high solubility in 0.33 M citric acid and 0.005 M DTPA. Three different field trials showed significant yield increments using the slow-release micronutrient fertilizer compared to the conventional micronutrients. Yield increments in rice were in the range of 10–55% over control (with no micronutrient and up to 17% over the conventional micronutrient fertilizers. There were significant increases in total uptake of zinc, iron, and manganese in the grain. Slow-release fertilizers also produced significant yield increases in potato as well as significant increase in vitamin C content of the tuber.

Particulate metallic debris in cemented total hip arthroplasty.

Science.gov (United States)

Salvati, E A; Betts, F; Doty, S B

1993-08-01

Several studies conducted by the authors in the last six years demonstrate that the generation of metallic debris is more severe with titanium alloy than with cobalt-chrome alloy femoral components in cemented total hip arthroplasty (THA). The debris is generated from the articulating surface, particularly if entrapped acrylic debris produces three-body wear, and from the stem surface when the component loosens and abrades against fragmented cement. In selected cases in which the titanium metallic debris is copious, premature failure and severe progressive bone loss occurs. Electron microscopy demonstrates that the particles of metallic debris can be extremely small (a few hundredths of 1 micron). They are phagocytized by the macrophages and transported to the phagolysosomes. In this highly corrosive environment, the very high surface area of the particles may release toxic concentrations of the constituents of the alloy intracellularly, probably leading to progressive cell degeneration and death, with subsequent release of intracellular enzymes and ingested metallic debris. This cycle most likely repeats itself, leading to tissue necrosis. The results presented do not support the use of titanium alloy femoral components for cemented THA, particularly for the articulating surface.

The 2017 Release Cloudy

Science.gov (United States)

Ferland, G. J.; Chatzikos, M.; Guzmán, F.; Lykins, M. L.; van Hoof, P. A. M.; Williams, R. J. R.; Abel, N. P.; Badnell, N. R.; Keenan, F. P.; Porter, R. L.; Stancil, P. C.

2017-10-01

We describe the 2017 release of the spectral synthesis code Cloudy, summarizing the many improvements to the scope and accuracy of the physics which have been made since the previous release. Exporting the atomic data into external data files has enabled many new large datasets to be incorporated into the code. The use of the complete datasets is not realistic for most calculations, so we describe the limited subset of data used by default, which predicts significantly more lines than the previous release of Cloudy. This version is nevertheless faster than the previous release, as a result of code optimizations. We give examples of the accuracy limits using small models, and the performance requirements of large complete models. We summarize several advances in the H- and He-like iso-electronic sequences and use our complete collisional-radiative models to establish the densities where the coronal and local thermodynamic equilibrium approximations work.

Silicone Doped Chitosan-Acrylamide Coencapsulated Urea Fertilizer: An Approach to Controlled Release Fertilizers

Directory of Open Access Journals (Sweden)

Sempeho Ibahati Siafu

2017-01-01

Full Text Available In the absence of special management practices, urea is known to undergo chemical transformations resulting in severe losses (≈60–70% of total fertilizer applied. In an attempt to design urea controlled release fertilizers in order to counterbalance the 60–70% loss, urea was cross-linked with chitosan and acrylamide under refluxed in situ copolymerization technique; the procedures were repeated with silicone doping prior cross-linking with MBA. The particles were characterized with FTIR/ATR, EDX, XRD, and SEM. The IR bands observed within 3426–409 cm−1 revealed the formation of new bands after coencapsulation for the νγN-H, νβN-H, νOH, νsNH2, νCH2, νC=O, δ′NH2, νC=C, δNH2, νC-N, βCH3, $C-N, γNH2, νC=O, and $CH2. Crystallinity indices for urea with and without silicone doping were found to be 50.9% and 72.1%, respectively, with a distinctive split peak at (d 12.30°. The formation of Microdunes and Microballs 3D network sized 0.64 μm was noted. Release profiles demonstrated that 80% N was released in a period of 30 days at RT and pH 7. The release patterns exhibited linear and deformed sigmoid release models. Empirically, the findings demonstrated that it is possible to design urea controlled release fertilizers with varying particle sizes and morphologies by using chitosan-acrylamide coencapsulation.

Strategies for neurotrophin-3 and chondroitinase ABC release from freeze-cast chitosan-alginate nerve-guidance scaffolds.

Science.gov (United States)

Francis, Nicola L; Hunger, Philipp M; Donius, Amalie E; Wegst, Ulrike G K; Wheatley, Margaret A

2017-01-01

Freeze casting, or controlled unidirectional solidification, can be used to fabricate chitosan-alginate (C-A) scaffolds with highly aligned porosity that are suitable for use as nerve-guidance channels. To augment the guidance of growth across a spinal cord injury lesion, these scaffolds are now evaluated in vitro to assess their ability to release neurotrophin-3 (NT-3) and chondroitinase ABC (chABC) in a controlled manner. Protein-loaded microcapsules were incorporated into C-A scaffolds prior to freeze casting without affecting the original scaffold architecture. In vitro protein release was not significantly different when comparing protein loaded directly into the scaffolds with release from scaffolds containing incorporated microcapsules. NT-3 was released from the C-A scaffolds for 8 weeks in vitro, while chABC was released for up to 7 weeks. Low total percentages of protein released from the scaffolds over this time period were attributed to limitation of diffusion by the interpenetrating polymer network matrix of the scaffold walls. NT-3 and chABC released from the scaffolds retained bioactivity, as determined by a neurite outgrowth assay, and the promotion of neurite growth across an inhibitory barrier of chondroitin sulphate proteoglycans. This demonstrates the potential of these multifunctional scaffolds for enhancing axonal regeneration through growth-inhibiting glial scars via the sustained release of chABC and NT-3. Copyright © 2014 John Wiley & Sons, Ltd. Copyright © 2014 John Wiley & Sons, Ltd.

Slow-release and organic fertilizers on early growth of Rangpur lime

Directory of Open Access Journals (Sweden)

Daniel Lucas Magalhães Machado

2011-06-01

Full Text Available Slow-release and organic fertilizers are promising alternatives to conventional fertilizers, as both reduce losses by leaching, volatilization and problems of toxicity and/or salinity to plants. The objective of this work was to evaluate the effect of different rates of the organic fertilizer Humato-Macota® compared with the slow-release fertilizer Osmocote® on the growth and nitrogen content in the dry matter of Rangpur lime. A field experiment was conducted in a factorial completely randomized design with an additional treatment (4 x 4 +1. The first factor consisted of four Humato­Macota® rates (0, 1, 2, and 3% applied to the substrate; the second factor consisted of the same Humato-Macota® concentrations, but applied as fortnightly foliar sprays; the additional treatment consisted of application of 5 kgm-3 Osmocote® 18-05-09. Means of all growth characteristics (plant height, total dry matter, root/shoot ratio and leaf area and the potential quantum yield of photosystem II (Fv/Fm were higher when plants were fertilized with the slow-release fertilizer. The organic fertilizer applied alone did not meet the N requirement of Rangpur lime.

Field study of the long-term release of block copolymers from fouling-release coatings

DEFF Research Database (Denmark)

Noguer, Albert Camós; Olsen, A.; Hvilsted, Søren

2017-01-01

The addition of block copolymers (i.e. oils) is a common technique to enhance the biofouling-resistance properties of poly(dimethylsiloxane) (PDMS)-based fouling-release coatings. These copolymers diffuse from the bulk to the surface of the coating, thus modifying the properties of the surface an...... fouling-release coatings. Finally, the potential of long-term field-studies is discussed, as compared to short-term laboratory experiments usually performed within fouling-release coatings studies....

Releases of radioactivity from uranium mills and effluent treatment costs

International Nuclear Information System (INIS)

Witherspoon, J.P.; Sears, M.B.; Blanco, R.E.

1977-01-01

Airborne releases of radioactive materials from uranium milling to the environment consist of ore dust, yellowcake dust, tailings dust, and radon gas while the mill is active. After a mill has ceased operations, tailings may be stabilized to minimize or prevent airborne releases of radioactive particulates. However, radon gas will continue to be released in amounts inversely proportional to the degree of stabilization treatment (and expense). Liquid waste disposal is by evaporation and natural seepage to the ground beneath the tailings impoundment area. The release of radioactive materials (and potential radiation exposures) determines the majority of costs associated with minimizing the environmental impact of uranium milling. Radwaste treatments to reduce estimated radiation doses to individuals to 3 to 5% of those received with current milling practices are equivalent to $0.66 per pounds of U 3 O 8 and 0.032 mill per kWhr of electricity. This cost would cover a high efficiency reverse jet bag filter and high energy venturi scrubbers for dusts, neutralization of liquids, and an asphalt-lined tailings basin with a clay core dam to reduce seepage. In addition, this increased cost would cover stabilization of tailings, after mill closure, with a 1-in. asphalt membrane topped by 2 ft of earth and 0.5 ft of crushed rock to provide protection against future leaching and wind erosion. The cost of reducing the radiological hazards associated with uranium milling to this degree would contribute about 0.4% to the current total cost of nuclear power

Kinetics of radiocesium released from contaminated soil by fertilizer solutions

International Nuclear Information System (INIS)

Chiang, P.N.; Wang, M.K.; Huang, P.M.; Wang, J.J.

2008-01-01

137 Cs is one of the major artificial radionuclides found in environments; but the mechanisms behind fertilizer-induced 137 Cs desorption from soil remain unknown. This study aimed to investigate the kinetics and mechanisms underlying the various cations and anions that cause Cs release from soil under acidic conditions. NH 4 H 2 PO 4 (1 M), 0.5 M (NH 4 ) 2 SO 4 , 1 M NH 4 Cl, 1 M KCl or 1 M NaCl solutions were added to 137 Cs-contaminated soil. The power function model well described the short term 137 Cs desorption with the solutions. The rate coefficients for 137 Cs release from soil in NH 4 H 2 PO 4 , (NH 4 ) 2 SO 4 , NH 4 Cl, and KCl solutions were 7.7, 7.3, 6.8, and 6.1 times higher than the rate observed in a NaCl solution, respectively. The NH 4 H 2 PO 4 and (NH 4 ) 2 SO 4 solutions induced significantly greater 137 Cs release from the contaminated soil than the NH 4 Cl, KCl and NaCl solutions. After four times repeated extractions with the fertilizer solutions, the total amount of 137 Cs extracted by (NH 4 ) 2 SO 4 and NH 4 Cl solutions reached equilibrium, while that extracted using an NH 4 H 2 PO 4 solution continued to increase. The combined effect of phosphate and protons was the major mechanism behind 137 Cs release from contaminated soils, when an NH 4 H 2 PO 4 solution was used

Calcein AM release-based cytotoxic cell assay for fish leucocytes.

Science.gov (United States)

Iwanowicz, Luke R; Densmore, Christine L; Ottinger, Christopher A

2004-02-01

A non-specific cytotoxic cell assay for fish is presented that is based on the release of the activated fluorochrome calcein AM from lysed carp epithelioma papulosum cyprini (EPC) cells. To establish the suitability of treating EPC cells with calcein AM the uptake and spontaneous release of the calcein AM by the EPC cells was evaluated. Incubation of 5 microM calcein AM in culture medium with 1x10(5)EPC cells well(-1)for a minimum of 3 h provided sufficient labelling. Spontaneous release of fluorescence from the labelled EPC cells during 10 h of post labelling incubation ranged from 30 to 39% of the total observed fluorescence. Cytotoxic activity of trout leucocytes was evaluated at three leucocyte to target cell ratios (10:1, 2:1 and 1:1) following incubation (4, 6, 8, and 10 h) with calcein AM-labelled EPC cells at 15 degrees C. In some instances, the monoclonal antibody specific for the NCC surface receptor NCCRP-1 (MAb5C.6) was included in the cultures. The activity of NCC cells was significantly inhibited in the presence of 0.25 microg well(-1)of MAb5C.6 relative to no antibody (Prelease assay.

Modelling of contaminant release from a uranium mine tailings site

International Nuclear Information System (INIS)

Kahnt, Rene; Metschies, Thomas

2007-01-01

Available in abstract form only. Full text of publication follows: Uranium mining and milling continuing from the early 1960's until 1990 close to the town of Seelingstaedt in Eastern Germany resulted in 4 tailings impoundments with a total tailings volume of about 105 Mio. m 3 . Leakage from these tailings impoundments enters the underlying aquifers and is discharged into surface water streams. High concentration of salts, uranium and several heavy metals are released from the tailings. At present the tailings impoundments are reshaped and covered. For the identification of suitable remediation options predictions of the contaminant release for different remediation scenarios have to be made. A compartment model representing the tailings impoundments and the surrounding aquifers for the calculation of contaminant release and transport was set up using the software GOLDSIM. This compartment model describes the time dependent hydraulic conditions within the tailings and the surrounding aquifers taking into account hydraulic and geotechnical processes influencing the hydraulic properties of the tailings material. A simple geochemical approach taking into account sorption processes as well as retardation by applying a k d -approach was implemented to describe the contaminant release and transport within the hydraulic system. For uranium as the relevant contaminant the simple approach takes into account additional geochemical conditions influencing the mobility. Alternatively the model approach allows to include the results of detailed geochemical modelling of the individual tailings zones which is than used as source term for the modelling of the contaminant transport in the aquifer and to the receiving streams. (authors)

Total Value of Phosphorus Recovery.

Science.gov (United States)

Mayer, Brooke K; Baker, Lawrence A; Boyer, Treavor H; Drechsel, Pay; Gifford, Mac; Hanjra, Munir A; Parameswaran, Prathap; Stoltzfus, Jared; Westerhoff, Paul; Rittmann, Bruce E

2016-07-05

Phosphorus (P) is a critical, geographically concentrated, nonrenewable resource necessary to support global food production. In excess (e.g., due to runoff or wastewater discharges), P is also a primary cause of eutrophication. To reconcile the simultaneous shortage and overabundance of P, lost P flows must be recovered and reused, alongside improvements in P-use efficiency. While this motivation is increasingly being recognized, little P recovery is practiced today, as recovered P generally cannot compete with the relatively low cost of mined P. Therefore, P is often captured to prevent its release into the environment without beneficial recovery and reuse. However, additional incentives for P recovery emerge when accounting for the total value of P recovery. This article provides a comprehensive overview of the range of benefits of recovering P from waste streams, i.e., the total value of recovering P. This approach accounts for P products, as well as other assets that are associated with P and can be recovered in parallel, such as energy, nitrogen, metals and minerals, and water. Additionally, P recovery provides valuable services to society and the environment by protecting and improving environmental quality, enhancing efficiency of waste treatment facilities, and improving food security and social equity. The needs to make P recovery a reality are also discussed, including business models, bottlenecks, and policy and education strategies.

Sterile insect supply, emergence, and release

International Nuclear Information System (INIS)

Dowell, R.V.; Worley, J.; Gomes, P.J.

2005-01-01

Insect mass-rearing for a sterile insect technique (SIT) programme is designed to move beyond the large-scale rearing of insects in a laboratory to the industrial production of consistently high-quality insects for sterilization and release. Each facility reflects the unique biology of the insect reared within it, but there are some generalities for all rearing facilities. Rearing insects in self-contained modules offers flexibility, and increased safety from catastrophic occurrences, compared with using a single building which houses all facets of the rearing process. Although mechanizing certain aspects of the rearing steps helps provide a consistently high-quality insect, successful mass-rearing and delivery depends largely upon the human component. Besides production in centralized facilities, insects can be produced from purchased eggs, or nowadays, adult insects are often obtained from specialized satellite emergence/collection facilities. Interest in commercializing insect production and release is increasing. Shipping sterile insects, sometimes over long distances, is now common practice. Procedures for handling and chilling adult insects, and providing food and water prior to release, are continually being improved. Sterile insects are released via static-release receptacles, ground-release systems, or most commonly from the air. The aerial release of chilled sterile insects is the most efficient method of release, especially when aircraft flight paths are guided by a Global Positioning System (GPS) linked to a computer-controlled release mechanism. (author)

In vitro effect of. Delta. sup 9 -tetrahydrocannabinol to stimulate somatostatin release and block that of luteinizing hormone-releasing hormone by suppression of the release of prostaglandin E sub 2

Energy Technology Data Exchange (ETDEWEB)

Rettori, V.; Aguila, M.C.; McCann, S.M. (Univ. of Texas Southwestern Medical Center at Dallas (United States)); Gimeno, M.F.; Franchi, A.M. (Centro de Estudios Farmacologicos y de Principios Naturales, Buenos Aires (Argentina))

1990-12-01

Previous in vivo studies have shown that {Delta}{sup 9}-tetrahydrocannabinol (THC), the principal active ingredient in marijuana, can suppress both luteinizing hormone (LH) and growth hormone (GH) secretion after its injection into the third ventricle of conscious male rats. The present studies were deigned to determine the mechanism of these effects. Various doses of THC were incubated with either stalk median eminence fragments (MEs) or mediobasal hypothalamic (MBH) fragments in vitro. Although THC (10 nM) did not alter basal release of LH-releasing hormone (LHRH) from MEs in vitro, it completely blocked the stimulatory action of dopamine or nonrepinephrine on LHRH release. The effective doses to block LHRH release were associated with a blockade of synthesis and release of prostaglandin E{sub 2} (PGE{sub 2}) from MBH in vitro. In contrast to the suppressive effect of THC on LHRH release, somatostatin release from MEs was enhanced in a dose-related manner with a minimal effective dose of 1 nM. Since PGE{sub 2} suppresses somatostatin release, this enhancement may also be related to the suppressive effect of THC on PGE{sub 2} synthesis and release. The authors speculate that these actions are mediated by the recently discovered THC receptors in the tissue. The results indicate that the suppressive effect of THC on LH release is mediated by a blockade of LHRH release, whereas the suppressive effect of the compound on growth hormone release is mediated, at least in part, by a stimulation of somatostatin release.

Satellite-based constraints on explosive SO2 release from Soufrière Hills Volcano, Montserrat

Science.gov (United States)

Carn, Simon A.; Prata, Fred J.

2010-09-01

Numerous episodes of explosive degassing have punctuated the 1995-2009 eruption of Soufrière Hills volcano (SHV), Montserrat, often following major lava dome collapses. We use ultraviolet (UV) and infrared (IR) satellite measurements to quantify sulfur dioxide (SO2) released by explosive degassing, which is not captured by routine ground-based and airborne gas monitoring. We find a total explosive SO2 release of ˜0.5 Tg, which represents ˜6% of total SO2 emissions from SHV since July 1995. The majority of this SO2 (˜0.4 Tg) was vented following the most voluminous SHV dome collapses in July 2003 and May 2006. Based on our analysis, we suggest that the SO2 burden measured following explosive disruption of lava domes depends on several factors, including the instantaneous lava effusion rate, dome height above the conduit, and the vertical component of directed explosions. Space-based SO2 measurements merit inclusion in routine gas monitoring at SHV and other dome-forming volcanoes.

The release of dissolved nutrients and metals from coastal sediments due to resuspension

Science.gov (United States)

Kalnejais, Linda H.; Martin, William R.; Bothner, Michael H.

2010-01-01

Coastal sediments in many regions are impacted by high levels of contaminants. Due to a combination of shallow water depths, waves, and currents, these sediments are subject to regular episodes of sediment resuspension. However, the influence of such disturbances on sediment chemistry and the release of solutes is poorly understood. The aim of this study is to quantify the release of dissolved metals (iron, manganese, silver, copper, and lead) and nutrients due to resuspension in Boston Harbor, Massachusetts, USA. Using a laboratory-based erosion chamber, a range of typical shear stresses was applied to fine-grained Harbor sediments and the solute concentration at each shear stress was measured. At low shear stress, below the erosion threshold, limited solutes were released. Beyond the erosion threshold, a release of all solutes, except lead, was observed and the concentrations increased with shear stress. The release was greater than could be accounted for by conservative mixing of porewaters into the overlying water, suggesting that sediment resuspension enhances the release of nutrients and metals to the dissolved phase. To address the long-term fate of resuspended particles, samples from the erosion chamber were maintained in suspension for 90. h. Over this time, 5-7% of the particulate copper and silver was released to the dissolved phase, while manganese was removed from solution. Thus resuspension releases solutes both during erosion events and over a longer timescale due to reactions of suspended particles in the water column. The magnitude of the annual solute release during erosion events was estimated by coupling the erosion chamber results with a record of bottom shear stresses simulated by a hydrodynamic model. The release of dissolved copper, lead, and phosphate due to resuspension is between 2% and 10% of the total (dissolved plus particulate phase) known inputs to Boston Harbor. Sediment resuspension is responsible for transferring a significant

Drug-loaded electrospun mats of poly(vinyl alcohol) fibres and their release characteristics of four model drugs

Science.gov (United States)

Taepaiboon, Pattama; Rungsardthong, Uracha; Supaphol, Pitt

2006-05-01

Mats of PVA nanofibres were successfully prepared by the electrospinning process and were developed as carriers of drugs for a transdermal drug delivery system. Four types of non-steroidal anti-inflammatory drug with varying water solubility property, i.e. sodium salicylate (freely soluble in water), diclofenac sodium (sparingly soluble in water), naproxen (NAP), and indomethacin (IND) (both insoluble in water), were selected as model drugs. The morphological appearance of the drug-loaded electrospun PVA mats depended on the nature of the model drugs. The 1H-nuclear magnetic resonance results confirmed that the electrospinning process did not affect the chemical integrity of the drugs. Thermal properties of the drug-loaded electrospun PVA mats were analysed by differential scanning calorimetry and thermogravimetric analysis. The molecular weight of the model drugs played a major role on both the rate and the total amount of drugs released from the as-prepared drug-loaded electrospun PVA mats, with the rate and the total amount of the drugs released decreasing with increasing molecular weight of the drugs. Lastly, the drug-loaded electrospun PVA mats exhibited much better release characteristics of the model drugs than drug-loaded as-cast films.

Controlled release of diuron from an alginate-bentonite formulation: water release kinetics and soil mobility study.

Science.gov (United States)

Fernández-Pérez, M; Villafranca-Sánchez, M; González-Pradas, E; Flores-Céspedes, F

1999-02-01

The herbicide diuron was incorporated in alginate-based granules to obtain controlled release (CR) properties. The standard formulation (alginate-herbicide-water) was modified by the addition of different sorbents. The effect on diuron release rate caused by incorporation of natural and acid-treated bentonites in alginate formulation was studied by immersion of the granules in water under static conditions. The release of diuron was diffusion-controlled. The time taken for 50% release of active ingredient to be released into water, T(50), was calculated for the comparison of formulations. The addition of bentonite to the alginate-based formulation produced the higher T(50) values, indicating slower release of the diuron. The mobility of technical and formulated diuron was compared by using soil columns. The use of alginate-based CR formulations containing bentonite produced a less vertical distribution of the active ingredient as compared to the technical product and commercial formulation. Sorption capacities of the various soil constituents for diuron were also determined using batch experiments.

Continuous operation of RODOS in case of long lasting releases

International Nuclear Information System (INIS)

Raskob, W.; Paesler-Sauer, J.; Rafat, M.

2003-01-01

Full text: Under the auspices of its RTD (Research and Technological Development) Framework Programmes, the European Commission has supported the development of the RODOS (Real-time On-line DecisiOn Support) system for off-site emergency management after nuclear accidents since the end of 1989. Significant additional funds have been provided by many national RTD programmes, research institutes and industrial collaborators. In particular, the German Ministry of Environment, Nature Conservation and Reactor Safety (BMU) financially contributed to the project with emphasis an early emergency response. The ongoing RTD work under the EC's 5 th Framework Programme lead to significant extensions, modifications and new developments of both the system and the application software integrated in the RODOS system. All new functions and software components, which have been successfully tested, build the content of RODOD version PV5.0, which has been released in April 2003. One of the new key features of the RODOS system is its capability to deal with release scenarios longer than 24 hours in all its modes of application: in automatic use, the release duration is unlimited; for interactive calculations, the release has to be limited to 47 days. The environmental contamination and the corresponding doses are calculated on a daily basis and add up to get the total values. When calculating early emergency actions (such as sheltering, administration of stable iodine tablets, and evacuation), the time sequence of potential doses from previous days are used to determine weather a certain intervention level has been or will be exceeded at any time during the release and, in that way, to define areas where potential actions might have been initiated in the past. In case of long term countermeasures, the user has been given the option to consider a number of countermeasures which could be implemented during the release phase. This has increased the flexibility of the module for those

Infrared spectroscopic characterization of monocytic microvesicles (microparticles) released upon lipopolysaccharide stimulation.

Science.gov (United States)

Lee, Joonsup; Wen, Beryl; Carter, Elizabeth A; Combes, Valery; Grau, Georges E R; Lay, Peter A

2017-07-01

Microvesicles (MVs) are involved in cell-cell interactions, including disease pathogenesis. Nondestructive Fourier-transform infrared (FTIR) spectra from MVs were assessed as a technique to provide new biochemical insights into a LPS-induced monocyte model of septic shock. FTIR spectroscopy provided a quick method to investigate relative differences in biomolecular content of different MV populations that was complementary to traditional semiquantitative omics approaches, with which it is difficult to provide information on relative changes between classes (proteins, lipids, nucleic acids, carbohydrates) or protein conformations. Time-dependent changes were detected in biomolecular contents of MVs and in the monocytes from which they were released. Differences in phosphatidylcholine and phosphatidylserine contents were observed in MVs released under stimulation, and higher relative concentrations of RNA and α-helical structured proteins were present in stimulated MVs compared with MVs from resting cells. FTIR spectra of stimulated monocytes displayed changes that were consistent with those observed in the corresponding MVs they released. LPS-stimulated monocytes had reduced concentrations of nucleic acids, α-helical structured proteins, and phosphatidylcholine compared with resting monocytes but had an increase in total lipids. FTIR spectra of MV biomolecular content will be important in shedding new light on the mechanisms of MVs and the different roles they play in physiology and disease pathogenesis.-Lee, J., Wen, B., Carter, E. A., Combes, V., Grau, G. E. R., Lay, P. A. Infrared spectroscopic characterization of monocytic microvesicles (microparticles) released upon lipopolysaccharide stimulation. © FASEB.

The gas release programs to increase competition in the European gas market

International Nuclear Information System (INIS)

Clastres, Cedric

2005-01-01

Regulators have implemented asymmetric regulation measures, such as gas release programs and market share targets, because of European gas supply features and gas market specificities. Empirical experiences show in line with economic theory that these regulation measures favour entry and competition without deterring investments. If we look at impacts on competition, they are mitigated. Some positive effects result from the increase in consumption or in importation and transportation infrastructure developments. But these regulations can also encourage anti-competitive behaviours like collusion, cream-skimming, reverse cherry picking or inefficient entries. Gas release measures establish a link between the incumbent and its competitors. A system of constraints on operators capacities can also appear. Thus, pricing or quantity strategies are more complex. Equilibrium prices are more volatile and very different of competition mark-up. The incumbent, for high gas release quantities and low supplies, can increase its costs to make more profit. This Raising Rivals' Costs strategy often occur if the gas release price is closer to supply costs. This strategy does not impact on consumers surplus but decreases welfare. The regulator can restore incentives to efficiency by setting gas release proportion function of incumbent's supplies. This proportion must be high enough to have a positive impact on the market because of incumbent's incentives to efficiency and greater total quantities sold by the two operators. But, on another way, it must not be too high as it could, thus, increase the probability of Raising Rivals' Costs or favour collusive strategies. (author) [fr

Development of paradigm for the study of amino acid neurotransmitter release in human autopsy brain samples

International Nuclear Information System (INIS)

Kuo, K.-W.; Dodd, P.R.

2001-01-01

Full text: This study attempted to establish a release protocol to characterize both the vesicular and cytoplasmic components of amino acid transmitter release in human synaptosomes. Experiments with rat synaptosomes showed that, with depolarizing concentrations of K + ions, vesicular release could be successfully differentiated from cytoplasmic release for preloaded L-[ 3 H ]glutamate and [ 14 C ]GABA. However, human tissue studies did not give clear-cut results. Experiments were carried out to optimize the release paradigm as well as to improve the vesicular uptake of labeled transmitters. A 'pulse- chase' protocol, with an unlabelled D-aspartate chase, was performed in human tissue samples in order to enhance the L-[ 3 H ] glutamate release signal derived from exocytosis by removing the cytoplasmic pool of L-[ 3 H ] glutamate first. However, the results showed that total release was not enhanced effectively in comparison with the non-pulse-chase protocol. In brief, the pulse-chase protocol did not build up the vesicular pool of L-[ 3 H ]glutamate, though the cytoplasmic L- [ 3 H ] glutamate pool was effectively depressed by D-aspartate. Further studies applied 4- aminopyridine (4-AP) to trigger release, to circumvent the problem of the reversal of plasma membrane transporters caused by raised K + ion concentrations. The results showed that the application of 4-AP elicited the release of amino acid transmitters from rat synaptosomes, but failed to produce successful release signals in the human tissue experiments. Our findings suggest that the vesicular compartment may be impaired by freezing and affected by post-mortem delay (PMD). Rat studies showed that the freezing step had a major effect on Ca 2+-dependent release, as less L- [3 H ]glutamate and [ 14 C ]GABA were released from the frozen rat tissue preparations. Moreover, there was an indication of a decline in L-[ 3 H ]glutamate release with increasing PMD. Copyright (2001) Australian Neuroscience Society

Aluminum corrosion product release kinetics

Energy Technology Data Exchange (ETDEWEB)

Edwards, Matt, E-mail: Matthew.Edwards@cnl.ca; Semmler, Jaleh; Guzonas, Dave; Chen, Hui Qun; Toor, Arshad; Hoendermis, Seanna

2015-07-15

Highlights: • Release of Al corrosion product was measured in simulated post-LOCA sump solutions. • Increased boron was found to enhance Al release kinetics at similar pH. • Models of Al release as functions of time, temperature, and pH were developed. - Abstract: The kinetics of aluminum corrosion product release was examined in solutions representative of post-LOCA sump water for both pressurized water and pressurized heavy-water reactors. Coupons of AA 6061 T6 were exposed to solutions in the pH 7–11 range at 40, 60, 90 and 130 °C. Solution samples were analyzed by inductively coupled plasma atomic emission spectroscopy, and coupon samples were analyzed by secondary ion mass spectrometry. The results show a distinct “boron effect” on the release kinetics, expected to be caused by an increase in the solubility of the aluminum corrosion products. New models were developed to describe both sets of data as functions of temperature, time, and pH (where applicable)

Evaluation of microplastic release caused by textile washing processes of synthetic fabrics.

Science.gov (United States)

De Falco, Francesca; Gullo, Maria Pia; Gentile, Gennaro; Di Pace, Emilia; Cocca, Mariacristina; Gelabert, Laura; Brouta-Agnésa, Marolda; Rovira, Angels; Escudero, Rosa; Villalba, Raquel; Mossotti, Raffaella; Montarsolo, Alessio; Gavignano, Sara; Tonin, Claudio; Avella, Maurizio

2018-05-01

A new and more alarming source of marine contamination has been recently identified in micro and nanosized plastic fragments. Microplastics are difficult to see with the naked eye and to biodegrade in marine environment, representing a problem since they can be ingested by plankton or other marine organisms, potentially entering the food web. An important source of microplastics appears to be through sewage contaminated by synthetic fibres from washing clothes. Since this phenomenon still lacks of a comprehensive analysis, the objective of this contribution was to investigate the role of washing processes of synthetic textiles on microplastic release. In particular, an analytical protocol was set up, based on the filtration of the washing water of synthetic fabrics and on the analysis of the filters by scanning electron microscopy. The quantification of the microfibre shedding from three different synthetic fabric types, woven polyester, knitted polyester, and woven polypropylene, during washing trials simulating domestic conditions, was achieved and statistically analysed. The highest release of microplastics was recorded for the wash of woven polyester and this phenomenon was correlated to the fabric characteristics. Moreover, the extent of microfibre release from woven polyester fabrics due to different detergents, washing parameters and industrial washes was evaluated. The number of microfibres released from a typical 5 kg wash load of polyester fabrics was estimated to be over 6,000,000 depending on the type of detergent used. The usage of a softener during washes reduces the number of microfibres released of more than 35%. The amount and size of the released microfibres confirm that they could not be totally retained by wastewater treatments plants, and potentially affect the aquatic environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Release modes and processes relevant to source-term calculations at Yucca Mountain

International Nuclear Information System (INIS)

Apted, M.J.

1994-01-01

The feasibility of permanent disposal of radioactive high-level waste (HLW) in repositories located in deep geologic formations is being studied world-wide. The most credible release pathway is interaction between groundwater and nuclear waste forms, followed by migration of radionuclide-bearing groundwater to the accessible environment. Under hydrologically unsaturated conditions, vapor transport of volatile radionuclides is also possible. The near-field encompasses the waste packages composed of engineered barriers (e.g. man-made materials, such as vitrified waste forms, corrosion-resistant containers), while the far-field includes the natural barriers (e.g. host rock, hydrologic setting). Taken together, these two subsystems define a series of multiple, redundant barriers that act to assure the safe isolation of nuclear waste. In the U.S., the Department of energy (DOE) is investigating the feasibility of safe, long-term disposal of high-level nuclear waste at the Yucca Mountain site in Nevada. The proposed repository horizon is located in non-welded tuffs within the unsaturated zone (i.e. above the water table) at Yucca Mountain. The purpose of this paper is to describe the source-term models for radionuclide release from waste packages at Yucca Mountain site. The first section describes the conceptual release modes that are relevant for this site and waste package design, based on a consideration of the performance of currently proposed engineered barriers under expected and unexpected conditions. No attempt is made to asses the reasonableness nor probability of occurrence for any specific release mode. The following section reviews the waste-form characteristics that are required to model and constrain the release of radionuclides from the waste package. The next section present mathematical models for the conceptual release modes, selected from those that have been implemented into a probabilistic total system assessment code developed for the Electric Power

Coronal Flux Rope Catastrophe Associated With Internal Energy Release

Science.gov (United States)

Zhuang, Bin; Hu, Youqiu; Wang, Yuming; Zhang, Quanhao; Liu, Rui; Gou, Tingyu; Shen, Chenglong

2018-04-01

Magnetic energy during the catastrophe was predominantly studied by the previous catastrophe works since it is believed to be the main energy supplier for the solar eruptions. However, the contribution of other types of energies during the catastrophe cannot be neglected. This paper studies the catastrophe of the coronal flux rope system in the solar wind background, with emphasis on the transformation of different types of energies during the catastrophe. The coronal flux rope is characterized by its axial and poloidal magnetic fluxes and total mass. It is shown that a catastrophe can be triggered by not only an increase but also a decrease of the axial magnetic flux. Moreover, the internal energy of the rope is found to be released during the catastrophe so as to provide energy for the upward eruption of the flux rope. As far as the magnetic energy is concerned, it provides only part of the energy release, or even increases during the catastrophe, so the internal energy may act as the dominant or even the unique energy supplier during the catastrophe.

An updated fracture-flow model for total-system performance assessment of Yucca Mountain

International Nuclear Information System (INIS)

Gauthier, J.H.

1994-01-01

Improvements have been made to the fracture-flow model being used in the total-system performance assessment of a potential high-level radioactive waste repository at Yucca Mountain, Nevada. The open-quotes weeps modelclose quotes now includes (1) weeps of varied sizes, (2) flow-pattern fluctuations caused by climate change, and (3) flow-pattern perturbations caused by repository heat generation. Comparison with the original weeps model indicates that allowing weeps of varied sizes substantially reduces the number of weeps and the number of containers contacted by weeps. However, flow-pattern perturbations caused by either climate change or repository heat generation greatly increases the number of containers contacted by weeps. In preliminary total-system calculations, using a phenomenological container-failure and radionuclide-release model, the weeps model predicts that radionuclide releases from a high-level radioactive waste repository at Yucca Mountain will be below the EPA standard specified in 40 CFR 191, but that the maximum radiation dose to an individual could be significant. Specific data from the site are required to determine the validity of the weep-flow mechanism and to better determine the parameters to which the dose calculation is sensitive

An updated fracture-flow model for total-system performance assessment of Yucca Mountain

International Nuclear Information System (INIS)

Gauthier, J.H.

1994-01-01

Improvements have been made to the fracture-flow model being used in the total-system performance assessment of a potential high-level radioactive waste repository at Yucca Mountain, Nevada. The ''weeps model'' now includes (1) weeps of varied sizes, (2) flow-pattern fluctuations caused by climate change, and (3) flow-pattern perturbations caused by repository heat generation. Comparison with the original weeps model indicates that allowing weeps of varied sizes substantially reduces the number of weeps and the number of containers contacted by weeps. However, flow-pattern perturbations caused by either climate change or repository heat generation greatly increases the number of containers contacted by weeps. In preliminary total-system calculations, using a phenomenological container-failure and radionuclide-release model, the weeps model predicts that radionuclide releases from a high-level radioactive waste repository at Yucca Mountain will be below the EPA standard specified in 40 CFR 191, but that the maximum radiation dose to an individual could be significant. Specific data from the site are required to determine the validity of the weep-flow mechanism and to better determine the parameters to which the dose calculation is sensitive

Treatment-Continuity of ADHD Compared Using Immediate-Release and Extended-Release MPH

Directory of Open Access Journals (Sweden)

J Gordon Millichap

2005-07-01

Full Text Available The continuity of methylphenidate (MPH therapy for ADHD in young Medicaid beneficiaries (ages 6 to 17 years treated with immediate-release (IR or extended-release (ER MPH formulations was compared in an analysis of statewide California Medicaid claims (2000-2003 conducted at Columbia University, New York; University of Pennsylvania, Philadelphia; and McNeil Pharmaceuticals, Fort Washington, PA.

Nitrogen accumulation and release by sunn hemp, calopo, mucana and devil bean in semi-arid Ghana

International Nuclear Information System (INIS)

Fosu, Mathias

2003-01-01

Four leguminous cover crops, Calopogonium mucunoides (calopo), Mucuna prupriens (mucuna), Crotalaria juncea (sunn hemp) and Crotalaria retusa (devil bean) were evaluated on the field in Northern Ghana for N 2 fixation capacity and N release. The proportion on N derived from the atmosphere (% Ndfa) by the cover crops ranged from 64.7 to 81% with mucuna giving the highest % Ndfa and calopo the least. The total N 2 fixed ranged from 59 to 109.5 kg ha 4 with devil bean giving the largest and the least from calopo. The dry matter yield of cover crops was positively correlated with the amount of N 2 , fixed but not with the percent of N derived from the atmosphere (%Ndfa). Sunn hemp, which had the best residue quality (least per cent cellulose, lignin, C N ratio and Lignin N ratio), released 50% of its N within the first two weeks while the other cover crops with relatively poor residue quality released 25% of their N within the same period. By the end of the rainy season sunn hemp had released 90% of the residue N while the other cover crops had released 80%. (author)

The importance of bacterial utilization of released phytoplankton photosynthate in two humic forest lakes in southern Finland

International Nuclear Information System (INIS)

Jones, R.I.; Salonen, K.

1985-01-01

Bacterial utilization of photosynthetically fixed dissolved organic carbon (PDOC) released from natural phytoplankton assemblages was studied in two small, extremely humic, forest lakes in southern Finland. Bacterial activity (measured us uptake of 14 C-glucose) and phytoplankton photosynthesis (measured as light uptake of 14 CO 2 ) could be most effectively separated using Nuclepore filters of pore 1-2 μm. Released PDOC was 10-67% of total phytoplankton carbon fixation during in situ experiments, and represented about 0.1% of total DOC. Net uptake of PDOC by bacteria was found to be about 20% during 24 hour laboratory incubations, although about 40% of PDOC present at the start of an experiment could be utilized by bacteria during a 24 hour period. PDOC does not provide a quantitatively important substrate supply fo bacterial respiration in humic forest lakes. (author)

Preparation of venlafaxine hydrochloride sustained-release tablets

Directory of Open Access Journals (Sweden)

GUO Lingling

2013-08-01

Full Text Available To prepare venlafxine hydrochloride sustained-release tablets.Hydroxypropylmethyl cellulose(HPMC and methyl cellulose(MC were used as main materials to prepare sustained-release tablets of velafaxine hydrochloride and the influence of important factors on in vitro release curves of venlafaxine hydrochloride sustained-release tablets was investigated.Results:The optimal prescription included 100 mg HPMC,25 mg MC,and 2.5% glidant in one tablet prepared with 30kN.The tablets were prepared with the method of wet granulation by NO.16 mesh sieve.The tablets exhibited good sustained-release property in phosphate buffered solution (pH=6.8.The as-prepared venlafxine hydrochloride sustained-release tablets have good sustained-release property.

The influence of Metolose structure on the free volume and the consequent metoprolol tartrate release of patches.

Science.gov (United States)

Papp, József; Marton, Sylvia; Süvegh, Károly; Zelkó, Romána

2009-01-01

Matrix-type patches containing Metoprolol tartrate were prepared from two types of Metolose and acrylate polymers. Metolose SM 4000 and Metolose 90SH 100.000SR were applied in different proportions in the patches where the total polymer content was kept constant in each sample. The purpose of the study was to investigate the effect of Metolose structure on the free volume of the patches and the consequent drug release profile. The drug release profiles were characterized by zero-order and first-order models. The results indicate that Metolose, containing hydroxypropyl ether groups and methyl ether groups, enables the formation of H-bonds, thus increasing the free volume holes and the consequent extent and rate of drug release of patches.

Effect of bioceramic functional groups on drug binding and release kinetics

Science.gov (United States)

Trujillo, Christopher

(p < 0.05) in the cumulative and percent of Vanc released from pre-immersed samples P-0 (1.505 +/- .014 mg; 33.59 +/- 1.35 %) to P-331 (1.581 +/- .057 mg; 42.27 +/- 1.51 %) of Vanc, respectively. Furthermore, in the first 4 hours, the deceleration of drug release from sample P-0 to P-331 decreased from -66.92 to -34.07 microg of Vanc/mL /hr 2, for control non immersed Cris and from -72.60 to -46.04 microg of Vanc/mL/hr2, for pre-immersed samples. Furthermore, during the first 4 hours of burst release the percentage of drug released from the total amount of drug loaded for non-immersed samples P-0 was 41 % and for P-331was 26 %. After the 4 hours of Vanc release the amount of Vanc available for release for samples P-0 and P-331 was .898 mg and .945 mg, respectively. The same relationship was found for pre-immersed samples during the first 4 hours of burst release the percentage of drug released from the total amount of drug loaded for samples P-0 was 42 % and for P-331 was 30 %. After the 4 hours of Vanc release the amount of Vanc available for release for samples P-0 and P-331 was .873 mg and 1.106 mg, respectively. These results indicated the effect of phosphate content on decreasing the drug release rate. The drug release kinetics study showed that the release of phosphate ions from the surface of Cris prior to drug loading exposed active silicate functional groups that enhanced drug binding by physisorption which in turn facilitated rapid release kinetics. On the other hand, a slower drug release rate was observed as the phosphate functional groups increased on the material surface due to chemisorption. Results from the present study indicate that it is possible to enhance the burst release stage of a bioceramic drug carrier by increasing the silicate functional groups. The sustained release profile can be engineered by controlling the phosphate content of the bioceramic drug carrier.

Qualità totale e mobilità totale Total Quality and Total Mobility

Directory of Open Access Journals (Sweden)

Giuseppe Trieste

2010-05-01

Full Text Available FIABA ONLUS (Italian Fund for Elimination of Architectural Barriers was founded in 2000 with the aim of promoting a culture of equal opportunities and, above all, it has as its main goal to involve public and private institutions to create a really accessible and usable environment for everyone. Total accessibility, Total usability and Total mobility are key indicators to define quality of life within cities. A supportive environment that is free of architectural, cultural and psychological barriers allows everyone to live with ease and universality. In fact, people who access to goods and services in the urban context can use to their advantage time and space, so they can do their activities and can maintain relationships that are deemed significant for their social life. The main aim of urban accessibility is to raise the comfort of space for citizens, eliminating all barriers that discriminate people, and prevent from an equality of opportunity. “FIABA FUND - City of ... for the removal of architectural barriers” is an idea of FIABA that has already affected many regions of Italy as Lazio, Lombardy, Campania, Abruzzi and Calabria. It is a National project which provides for opening a bank account in the cities of referring, in which for the first time, all together, individuals and private and public institutions can make a donation to fund initiatives for the removal of architectural barriers within its own territory for a real and effective total accessibility. Last February the fund was launched in Rome with the aim of achieving a Capital without barriers and a Town European model of accessibility and usability. Urban mobility is a prerequisite to access to goods and services, and to organize activities related to daily life. FIABA promotes the concept of sustainable mobility for all, supported by the European Commission’s White Paper. We need a cultural change in management and organization of public means, which might focus on

Influence of the pneumatic tourniquet on patella tracking in total knee arthroplasty: a prospective randomized study in 100 patients

DEFF Research Database (Denmark)

Husted, Henrik; Toftgaard Jensen, T

2005-01-01

One hundred consecutive patients with osteoarthritis of the knee joint and scheduled for primary total knee arthroplasty performed in a bloodless field were prospectively randomized to have the tourniquet inflated on either straight leg or maximally flexed knee. There was no difference in the num...... deflation led to better patella tracking and saved 5 (31%) of 16 releases with no difference between groups. We recommend tourniquet deflation and reevaluation of patella tracking before performing lateral release in patellar maltracking....

28 CFR 571.22 - Release clothing and transportation.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Release clothing and transportation. 571... AND RELEASE RELEASE FROM CUSTODY Release Gratuities, Transportation, and Clothing § 571.22 Release clothing and transportation. (a) Staff shall provide release clothing appropriate for the time of year and...

The Study of Prompt and Delayed Muon Induced Fission. I.Total kinetic energies and mass distributions

NARCIS (Netherlands)

David, P; Hartfiel, J.; Janszen, H.; Petitjean, C.; Reist, H.W.; Polikanov, S.M.; Konijn, J.; Laat, de C.T.A.M.; Taal, A.; Krogulski, T.; Johansson, T.; Tibell, G.; Achard van Enschut, d' J.F.M.

1987-01-01

Mass yield and total kinetic energy release (TKE) distributions of fragments from prompt and delayed muon induced fission, separately, have been measured for the isotopes235U,238U,237Np and242Pu. The distributions from prompt muon induced fission are compared with the corresponding distributions

Interleukin 1α inhibits prostaglandin E2 release to suppress pulsatile release of luteinizing hormone but not follicle-stimulating hormone

International Nuclear Information System (INIS)

Rettori, V.; McCann, S.M.; Gimeno, M.F.; Karara, A.; Gonzalez, M.C.

1991-01-01

Interleukin 1α (IL-1α), a powerful endogenous pyrogen released from monocytes and macrophages by bacterial endotoxin, stimulates corticotropin, prolactin, and somatotropin release and inhibits thyrotropin release by hypothalamic action. The authors injected recombinant human IL-1α into the third cerebral ventricle, to study its effect on the pulsatile release of follicle-stimulating hormone (FSH) and luteinizing hormone (LH) in conscious, freely moving, ovariectomized rats. Intraventricular injection of 0.25 pmol of IL-1α caused an almost immediate reduction of plasma LH concentration. To determine the mechanism of the suppression of LH release, mediobasal hypothalamic fragments were incubated in vitro with IL-1α (10 pM) and the release of LH-releasing hormone (LHRH) and prostaglandin E 2 into the medium was measured by RIA in the presence or absence of nonrepinephrine. 1α reduced basal LHRH release and blocked LHRH release induced by nonrepinephrine. In conclusion, IL-1α suppresses LH but not FSH release by an almost complete cessation of pulsatile release of LH in the castrated rat. The mechanism of this effect appears to be by inhibition of prostaglandin E 2 -mediated release of LHRH

Phosphorus release behaviors of poultry litter biochar as a soil amendment

International Nuclear Information System (INIS)

Wang, Yue; Lin, Yingxin; Chiu, Pei C.; Imhoff, Paul T.; Guo, Mingxin

2015-01-01

Phosphorus (P) may be immobilized and consequently the runoff loss risks be reduced if poultry litter (PL) is converted into biochar prior to land application. Laboratory studies were conducted to examine the water extractability of P in PL biochar and its release kinetics in amended soils. Raw PL and its biochar produced through 400 °C pyrolysis were extracted with deionized water under various programs and measured for water extractable P species and contents. The materials were further incubated with a sandy loam at 20 g kg −1 soil and intermittently leached with water for 30 days. The P release kinetics were determined from the P recovery patterns in the water phase. Pyrolysis elevated the total P content from 13.7 g kg −1 in raw PL to 27.1 g kg −1 in PL biochar while reduced the water-soluble P level from 2.95 g kg −1 in the former to 0.17 g kg −1 in the latter. The thermal treatment transformed labile P in raw PL to putatively Mg/Ca phosphate minerals in biochar that were water-unextractable yet proton-releasable. Orthophosphate was the predominant form of water-soluble P in PL biochar, with condensed phosphate (e.g., pyrophosphate) as a minor form and organic phosphate in null. Release of P from PL biochar in both water and neutral soils was at a slower and steadier rate over a longer time period than from raw PL. Nevertheless, release of P from biochar was acid-driven and could be greatly promoted by the media acidity. Land application of PL biochar at soil pH-incorporated rates and frequency will potentially reduce P losses to runoffs and minimize the adverse impact of waste application on aquatic environments. - Highlights: • The predominant portion of P in poultry litter biochar is water insoluble. • Poultry litter P was immobilized by forming Ca/Mg (pyro)phosphates in biochar. • Release of P from biochar was slower and steadier than from raw poultry litter. • Soil pH greatly influenced the P release patterns of poultry litter biochar

Phosphorus release behaviors of poultry litter biochar as a soil amendment

Energy Technology Data Exchange (ETDEWEB)

Wang, Yue [Department of Civil and Environmental Engineering, University of Delaware, Newark, DE 19716 (United States); Lin, Yingxin [Department of Agriculture and Natural Resources, Delaware State University, Dover, DE 19901 (United States); Chiu, Pei C.; Imhoff, Paul T. [Department of Civil and Environmental Engineering, University of Delaware, Newark, DE 19716 (United States); Guo, Mingxin, E-mail: mguo@desu.edu [Department of Agriculture and Natural Resources, Delaware State University, Dover, DE 19901 (United States)

2015-04-15

Phosphorus (P) may be immobilized and consequently the runoff loss risks be reduced if poultry litter (PL) is converted into biochar prior to land application. Laboratory studies were conducted to examine the water extractability of P in PL biochar and its release kinetics in amended soils. Raw PL and its biochar produced through 400 °C pyrolysis were extracted with deionized water under various programs and measured for water extractable P species and contents. The materials were further incubated with a sandy loam at 20 g kg{sup −1} soil and intermittently leached with water for 30 days. The P release kinetics were determined from the P recovery patterns in the water phase. Pyrolysis elevated the total P content from 13.7 g kg{sup −1} in raw PL to 27.1 g kg{sup −1} in PL biochar while reduced the water-soluble P level from 2.95 g kg{sup −1} in the former to 0.17 g kg{sup −1} in the latter. The thermal treatment transformed labile P in raw PL to putatively Mg/Ca phosphate minerals in biochar that were water-unextractable yet proton-releasable. Orthophosphate was the predominant form of water-soluble P in PL biochar, with condensed phosphate (e.g., pyrophosphate) as a minor form and organic phosphate in null. Release of P from PL biochar in both water and neutral soils was at a slower and steadier rate over a longer time period than from raw PL. Nevertheless, release of P from biochar was acid-driven and could be greatly promoted by the media acidity. Land application of PL biochar at soil pH-incorporated rates and frequency will potentially reduce P losses to runoffs and minimize the adverse impact of waste application on aquatic environments. - Highlights: • The predominant portion of P in poultry litter biochar is water insoluble. • Poultry litter P was immobilized by forming Ca/Mg (pyro)phosphates in biochar. • Release of P from biochar was slower and steadier than from raw poultry litter. • Soil pH greatly influenced the P release patterns

Determination of Radiological, Material and Organizational Measures for Reuse of Conditionally Released Materials from Decommissioning

International Nuclear Information System (INIS)

Ondra, F.; Vasko, M.; Necas, V.

2012-01-01

An important part of nuclear installation decommissioning is conditional release of materials. The mass of conditionally released materials can significantly influence radioactive waste management and capacity of radioactive waste repository. The influence on a total decommissioning cost is also not negligible. Several scenarios for reuse of conditionally released materials were developed within CONRELMAT project. Each scenario contains preparation phase, construction phase and operation phase. For each above mentioned phase is needed to determine radiological, material, organizational and other constraints for conditionally released materials reuse to not break exposure limits for staff and public. Constraints are determined on the basis of external and internal exposure calculations in created models for selected takes in particular scenarios phases. The paper presents a developed methodology for determination of part of above mentioned constraints concerning external exposure of staff or public. Values of staff external exposure are also presented in paper to ensure that staff or public exposure does not break the limits. The methodology comprises a proposal of following constraints: radionuclide limit concentration of conditionally released materials for specific scenarios and nuclide vectors, specific deployment of conditionally released materials eventually shielding materials, staff and public during the scenario's phases, organizational measures concerning time of staff's or public's stay in the vicinity of conditionally released materials for individual performed scenarios and nuclide vectors. The paper further describes VISIPLAN 3D ALARA calculation planning software tool used for calculation of staff's and public's external exposure for individual scenarios. Several other parallel papers proposed for HND2012 are presenting selected details of the project.(author).

Insulin release by glucagon and secretin

DEFF Research Database (Denmark)

Kofod, Hans; Andreu, D; Thams, P

1988-01-01

Secretin and glucagon potentiate glucose-induced insulin release. We have compared the effects of secretin and glucagon with that of four hybrid molecules of the two hormones on insulin release and formation of cyclic AMP (cAMP) in isolated mouse pancreatic islets. All six peptides potentiated...... the release of insulin at 10 mM D-glucose, and their effects were indistinguishable with respect to the dynamics of release, dose-response relationship, and glucose dependency. However, measurements of cAMP accumulation in the presence of the phosphodiesterase inhibitor 3-isobutyl-1-methylxanthine (10(-4) M...... potentiating effects of secretin and glucagon on glucose-induced insulin release, their modes of action may be different....

Silver nanoparticle release from commercially available plastic food containers into food simulants

DEFF Research Database (Denmark)

Mackevica, Aiga; Olsson, Mikael Emil; Hansen, Steffen Foss

2016-01-01

. In the current study, we investigated four brands of commercially available plastic food storage containers and measured the total amount of silver, particle size and number concentration, and the migration rates into three different food simulants (Milli-Q grade water, 10 % ethanol, and 3 % acetic acid) for 10...... days at 40 °C. The experimental setup was made according to the European Commission Directive (EU 10/2011) for articles intended to be in contact with food. The total amount of silver in plastic containers and migration solutions was quantified by ICP-MS analysis, and the size of the migrated particles...... was investigated by single particle ICP-MS and TEM-EDS. The total mass and median size of released particulate Ag were generally highest in 3 % acetic acid for three out of four food container brands. The total content of silver in the containers varied from 13 to 42 µg/g. The highest migration was observed...

ATP Release and Effects in Pancreas

DEFF Research Database (Denmark)

Novak, Ivana; Amstrup, Jan; Henriksen, Katrine Lütken

2003-01-01

ATP and other nucleotides are released from various cells, but the pathway and physiological stimulus for ATP release are often unclear. The focus of our studies is the understanding of ATP release and signaling in rat exocrine pancreas. In acinar suspension mechanical stimulation, hypotonic shock...

Controlled Release Formulations of Auxinic Herbicides

Science.gov (United States)

Kowalski, Witold J.; Siłowiecki, Andrzej.; Romanowska, Iwona; Glazek, Mariola; Bajor, Justyna; Cieciwa, Katarzyna; Rychter, Piotr

2013-04-01

Controlled release formulations are applied extensively for the release of active ingredients such as plant protection agents and fertilizers in response to growing concern for ecological problems associated with increased use of plant protection chemicals required for intensive agricultural practices [1]. We synthesized oligomeric mixtures of (R,S)-3-hydroxy butyric acid chemically bonded with 2,4-D, Dicamba and MCPA herbicides (HBA) respectively, and determined their molecular structure and molecular weight dispersion by the size exclusion chromatography, proton magnetic resonance spectrometry and electro-spray ionization mass spectrometry. Further we carried out bioassays of herbicidal effectiveness of the HBA herbicides vs. series of dicotyledonous weeds and crop injury tests [2, 3, 4]. Field bioassays were accomplished according to the EPPO standards [5]. Groups of representative weeds (the development stages in the BCCH scale: 10 - 30) were selected as targets. Statistical variabilities were assessed by the Fisher LSD test for plants treated with the studied herbicides in form of HBA oligomers, the reference herbicides in form of dimethyl ammonium salts (DMA), and untreated plants. No statistically significant differences in the crop injuries caused by the HBA vs. the DMA reference formulation were observed. The effectiveness of the HBA herbicides was lower through the initial period (ca. 2 weeks) relative to the DMA salts, but a significant increase in the effectiveness of the HBA systems followed during the remaining fraction of each assay. After 6 weeks all observed efficiencies approached 100%. The death of weeds treated with the HBA herbicides was delayed when compared with the DMA reference herbicides. The delayed uptake observed for the HBA oligomers relative to the DMA salts was due to controlled release phenomena. In case of the DMA salts the total amount of active ingredients was available at the target site. By contrast, the amount of an active

Hydraulic release oil tool

International Nuclear Information System (INIS)

Mims, M.G.; Mueller, M.D.; Ehlinger, J.C.

1992-01-01

This patent describes a hydraulic release tool. It comprises a setting assembly; a coupling member for coupling to drill string or petroleum production components, the coupling member being a plurality of sockets for receiving the dogs in the extended position and attaching the coupling member the setting assembly; whereby the setting assembly couples to the coupling member by engagement of the dogs in the sockets of releases from and disengages the coupling member in movement of the piston from its setting to its reposition in response to a pressure in the body in exceeding the predetermined pressure; and a relief port from outside the body into its bore and means to prevent communication between the relief port and the bore of the body axially of the piston when the piston is in the setting position and to establish such communication upon movement of the piston from the setting position to the release position and reduce the pressure in the body bore axially of the piston, whereby the reduction of the pressure signals that the tool has released the coupling member

Controlled release of mitomycin C from PHEMAH-Cu(II) cryogel membranes.

Science.gov (United States)

Bakhshpour, Monireh; Yavuz, Handan; Denizli, Adil

2018-02-19

Molecular imprinting technique was used for the preparation of antibiotic and anti-neoplastic chemotherapy drug (mitomycin C) imprinted cryogel membranes (MMC-ICM). The membranes were synthezied by using metal ion coordination interactions with N-methacryloyl-(l)-histidine methyl ester (MAH) functional monomer and template molecules (i.e. MMC). The 2-hydroxyethyl methacrylate (HEMA) monomer and methylene bisacrylamide (MBAAm) crosslinker were used for the preparation of mitomycin C imprinted cryogel membranes by radical suspension polymerization technique. The imprinted cryogel membranes were characterized by scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET), Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR) and swelling degree measurements. Cytotoxicity of MMC-ICMs was investigated using mouse fibroblast cell line L929. Time-dependent release of MMC was demonstrated within 150 h from cryogel membranes. Cryogels demonstrated very high MMC loading efficiency (70-80%) and sustained MMC release over hours.

Quantifying Ca2+ release and inactivation of Ca2+ release in fast- and slow-twitch muscles.

Science.gov (United States)

Barclay, C J

2012-12-01

The aims of this study were to quantify the Ca(2+) release underlying twitch contractions of mammalian fast- and slow-twitch muscle and to comprehensively describe the transient inactivation of Ca(2+) release following a stimulus. Experiments were performed using bundles of fibres from mouse extensor digitorum longus (EDL) and soleus muscles. Ca(2+) release was quantified from the amount of ATP used to remove Ca(2+) from the myoplasm following stimulation. ATP turnover by crossbridges was blocked pharmacologically (N-benzyl-p-toluenesulphonamide for EDL, blebbistatin for soleus) and muscle heat production was used as an index of Ca(2+) pump ATP turnover. At 20°C, Ca(2+) release in response to a single stimulus was 34 and 84 μmol (kg muscle)(-1) for soleus and EDL, respectively, and increased with temperature (30°C: soleus, 61 μmol kg(-1); EDL, 168 μmol kg(-1)). Delivery of another stimulus within 100 ms of the first produced a smaller Ca(2+) release. The maximum magnitude of the decrease in Ca(2+) release was greater in EDL than soleus. Ca(2+) release recovered with an exponential time course which was faster in EDL (mean time constant at 20°C, 32.1 ms) than soleus (65.6 ms) and faster at 30°C than at 20°C. The amounts of Ca(2+) released and crossbridge cycles performed are consistent with a scheme in which Ca(2+) binding to troponin-C allowed an average of ∼1.7 crossbridge cycles in the two muscles.

Release of fission products and post-pile creep behaviour of irradiated fuel rods stored under dry conditions

International Nuclear Information System (INIS)

Kaspar, G.; Peehs, M.; Bokelmann, R.; Jorde, D.; Schoenfeld, H.; Haas, W.; Bleier, A.; Rutsch, F.

1985-06-01

The release of moisture and fission products (Kr-85, H-3 and I-129) under dry storage conditions has been examined on six fuel rods which have become defective in the reactor. During the examinations, inert conditions prevailed and limited air inlet was allowed temporarily. The storage temperature was 400 0 C. The residual moisture content of the fuel rods was approx. 5 g. At the beginning of the test, the total moisture content and 0,05% (max.) of the fission gas inventory were released. Under inert conditions, fission gas was not released during a prolonged period of time. Under oxidizing conditions, however, fission gas was released in the course of UO 2 oxidation. Post-pile creep of Zircaloy cladding tubes was measured at temperatures between 350 and 395 0 C and interval gauge pressures between 69 and 110 bar. The creep curves indicate that the irradiated cladding tube specimens still bear internal residual stresses which contribute through their relaxation to the post-pile creep. (orig.) [de

Tritium breeding and release-rate kinetics from neutron-irradiated lithium oxide

International Nuclear Information System (INIS)

Quanci, J.F.

1989-01-01

The research encompasses the measurement of the tritium breeding and release-rate kinetics from lithium oxide, a ceramic tritium-breeding material. A thermal extraction apparatus which allows the accurate measurement of the total tritium inventory and release rate from lithium oxide samples under different temperatures, pressures and carrier-gas compositions with an uncertainty not exceeding 3% was developed. The goal of the Lithium Blanket Module program was to determine if advanced computer codes could accurately predict the tritium production in the lithium oxide blanket of a fusion power plant. A fusion blanket module prototype, was built and irradiated with a deuterium-tritium fusion-neutron source. The tritium production throughout the module was modeled with the MCNP three dimensional Monte Carlo code and was compared to the assay of the tritium bred in the module. The MCNP code accurately predicted tritium-breeding trends but underestimated the overall tritium breeding by 30%. The release rate of tritium from small grain polycrystalline sintered lithium oxide with a helium carrier gas from 300 to 450 C was found to be controlled by the first order surface desorption of mono-tritiated water. When small amounts of hydrogen were added to the helium carrier gas, the first order rate constant increased from the isotopic exchange of hydrogen for tritium at the lithium oxide surface occurring in parallel with the first order desorption process. The isotopic-exchange first order rate constant temperature dependence and hydrogen partial pressure dependence were evaluated. Large single crystals of lithium oxide were fabricated by the vacuum fusion technique. The release rate of tritium from the large single crystals was found to be controlled by diffusion, and the mixed diffusion-desorption controlled release regime

Heat release from B4C oxidation in steam and air

International Nuclear Information System (INIS)

Belovsky, L.

1996-01-01

BWR and some PWR cores contain boron carbide (B 4 C) as neutron absorber. During a severe accident, the B 4 C can potentially react with steam under release of heat and hydrogen. Although models for B 4 C oxidation already exist in MELCOR and SCDAP/RELAP5, a development of a new model for another computer code seems to be difficult due to a missing comprehensive description of the current modelling methodology and scarce experimental data. The aim of this paper is to highlight the key points of the B 4 C oxidation using the existing available experimental data and to perform a simple heat balance analysis of the B 4 C/steam and B 4 C/air chemical reactions. The analysis of literature data shows that the B 4 C oxidation phenomenon is qualitatively well described below 1000 deg. C. However, no reliable data exist for the reaction kinetics especially above this temperature. It was found that the experimental results strongly depend on the experimental arrangement. The reaction heats, calculated in this study, indicate that the B 4 C oxidation is an exothermic reaction, releasing more heat in air than in steam. The formation of boric acids from the boron oxide increases the heat release from B 4 C by ∼ 10%, in the worst case. Although the total heat, released in a PWR core from the B 4 C oxidation, is probably much smaller than the heat released from the Zr/steam reaction, it is not excluded that the B 4 C oxidation can locally contribute to the damage of the control elements due to local overheating. Modelling of these phenomena is, however, very difficult due to the complex geometry of the liquefied control elements and due to absence of suitable data on the reaction kinetics. (author). 25 refs, 2 figs, 3 tabs

Massive radiological releases profoundly differ from controlled releases

International Nuclear Information System (INIS)

Pascucci-Cahen, Ludivine; Patrick, Momal

2012-11-01

Preparing for a nuclear accident implies understanding potential consequences. While many specialized experts have been working on different particular aspects, surprisingly little effort has been dedicated to establishing the big picture and providing a global and balanced image of all major consequences. IRSN has been working on the cost of nuclear accidents, an exercise which must strive to be as comprehensive as possible since any omission obviously underestimates the cost. It therefore provides (ideally) an estimate of all cost components, thus revealing the structure of accident costs, and hence sketching a global picture. On a French PWR, it appears that controlled releases would cause an 'economical' accident with limited radiological consequences when compared to other costs; in contrast, massive releases would trigger a major crisis with strong radiological consequences. The two types of crises would confront managers with different types of challenges. (authors)

Dose commitments due to radioactive releases from nuclear power plant sites in 1989

International Nuclear Information System (INIS)

Baker, D.A.

1993-02-01

Population and individual radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1989. Fifty-year dose commitments for a one-year exposure from both liquid and atmospheric releases were calculated for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 72 reactor sites. This report tabulates the results of these calculations, showing the dose commitments for both water and airborne pathways for each age group and organ. Also included for each of the sites is an estimate of individual doses which are compared with 10 CFR Part 50, Appendix I design objectives. The total collective dose commitments (from both liquid and airborne pathways) for each site ranged from a high of 14 person-rem to a low of 0.005 person-rem for the sites with plants in operation and producing power during the year. The arithmetic mean was 1.2 person-rem. The total population dose for all sites was estimated at 84 person-rem for the 140 million people considered at risk. The individual dose commitments estimated for all sites were below the Appendix I design objectives

Dose commitments due to radioactive releases from nuclear power plant sites in 1989

Energy Technology Data Exchange (ETDEWEB)

Baker, D.A. (Pacific Northwest Lab., Richland, WA (United States))

1993-02-01

Population and individual radiation dose commitments have been estimated from reported radionuclide releases from commercial power reactors operating during 1989. Fifty-year dose commitments for a one-year exposure from both liquid and atmospheric releases were calculated for four population groups (infant, child, teen-ager and adult) residing between 2 and 80 km from each of 72 reactor sites. This report tabulates the results of these calculations, showing the dose commitments for both water and airborne pathways for each age group and organ. Also included for each of the sites is an estimate of individual doses which are compared with 10 CFR Part 50, Appendix I design objectives. The total collective dose commitments (from both liquid and airborne pathways) for each site ranged from a high of 14 person-rem to a low of 0.005 person-rem for the sites with plants in operation and producing power during the year. The arithmetic mean was 1.2 person-rem. The total population dose for all sites was estimated at 84 person-rem for the 140 million people considered at risk. The individual dose commitments estimated for all sites were below the Appendix I design objectives.

Uniformity of Peptide Release Is Maintained by Methylation of Release Factors

Directory of Open Access Journals (Sweden)

William E. Pierson

2016-09-01

Full Text Available Termination of protein synthesis on the ribosome is catalyzed by release factors (RFs, which share a conserved glycine-glycine-glutamine (GGQ motif. The glutamine residue is methylated in vivo, but a mechanistic understanding of its contribution to hydrolysis is lacking. Here, we show that the modification, apart from increasing the overall rate of termination on all dipeptides, substantially increases the rate of peptide release on a subset of amino acids. In the presence of unmethylated RFs, we measure rates of hydrolysis that are exceptionally slow on proline and glycine residues and approximately two orders of magnitude faster in the presence of the methylated factors. Structures of 70S ribosomes bound to methylated RF1 and RF2 reveal that the glutamine side-chain methylation packs against 23S rRNA nucleotide 2451, stabilizing the GGQ motif and placing the side-chain amide of the glutamine toward tRNA. These data provide a framework for understanding how release factor modifications impact termination.

Comparison of extended-release epidural morphine with femoral nerve block to patient-controlled epidural analgesia for postoperative pain control of total knee arthroplasty: a case-controlled study.

Science.gov (United States)

Sugar, Scott L; Hutson, Larry R; Shannon, Patrick; Thomas, Leslie C; Nossaman, Bobby D

2011-01-01

Because newer anticoagulation strategies for total knee replacement present potentially increased risk of neuraxial analgesia, there is movement away from using patient-controlled epidural analgesia (PCEA) for pain control. This concern opens the door for other regional modalities in postoperative analgesia, including the use of extended-release epidural morphine (EREM) combined with a femoral nerve block (FNB). This study was a prospective observational chart review with the use of recent historical controls in patients undergoing unilateral total knee replacement. Outcomes of interest were 0-, 24-, and 48-hour postoperative pain scores using the visual analog scale (VAS); incidence of side effects; and time spent in the postanesthesia care unit (PACU). Postoperative pain scores at 24 and 48 hours in the EREM and FNB group (n  =  14; 2.6 ± 0.6 and 5.0 ± 0.9, respectively) were comparable to the PCEA group (n  =  14; 3.8 ± 0.6 and 4.2 ± 0.9). The PACU time was shorter in the EREM and FNB group (2.4 ± 0.3 hours) compared with PCEA (3.6 ± 0.3 hours, P  =  .02). No statistically significant difference was found in the incidence of side effects between the 2 groups. The VAS scores at 24 and 48 hours indicate that EREM and FNB provide comparable analgesia to PCEA. The trend toward shorter PACU times represents an opportunity for cost-identification analysis. The study data are limited by their observational nature and the small number of patients involved; nevertheless, this study demonstrates a therapeutic equivalence to PCEA that may be more cost effective.

Allegheny County Toxics Release Inventory

Data.gov (United States)

Allegheny County / City of Pittsburgh / Western PA Regional Data Center — The Toxics Release Inventory (TRI) data provides information about toxic substances released into the environment or managed through recycling, energy recovery, and...

Integrated Scheduling of Production and Distribution with Release Dates and Capacitated Deliveries

Directory of Open Access Journals (Sweden)

Xueling Zhong

2016-01-01

Full Text Available This paper investigates an integrated scheduling of production and distribution model in a supply chain consisting of a single machine, a customer, and a sufficient number of homogeneous capacitated vehicles. In this model, the customer places a set of orders, each of which has a given release date. All orders are first processed nonpreemptively on the machine and then batch delivered to the customer. Two variations of the model with different objective functions are studied: one is to minimize the arrival time of the last order plus total distribution cost and the other is to minimize total arrival time of the orders plus total distribution cost. For the former one, we provide a polynomial-time exact algorithm. For the latter one, due to its NP-hard property, we provide a heuristic with a worst-case ratio bound of 2.

Comparative evaluation of fluoride release from PRG-composites and compomer on application of topical fluoride: An in-vitro study

Directory of Open Access Journals (Sweden)

Dhull K

2009-03-01

Full Text Available Aims and Objective: To determine the fluoride release from Giomer and Compomer, using different topical fluoride regimes, and to compare the amount of fluoride release from giomer with that of compomer. Materials and Method: Forty-eight specimens of each giomer and compomer were divided into four treatment groups, namely, control group, fluoridated dentifrice (500 ppm once daily group, fluoridated dentifrice (500 ppm twice daily group, fluoridated dentifrice (500 ppm once daily + fluoridated mouthwash (225 ppm group. Each specimen was suspended in demineralizing solution for six hours and remineralizing solution for 18 hours. Fluoride release was measured in both the demineralizing solution and remineralizing solution daily for seven days. Total daily fluoride release for each specimen was calculated by adding the amount released in the demineralizing solution to that released in remineralizing solution. Results and Conclusion: The fluoride release (ppm was found to be more in Giomer when compared to Compomer. The fluoride released from Giomer and Compomer was significantly greater in the acidic demineralizing solution than in the neutral remineralizing solution. It was found that increasing fluoride exposure significantly increased fluoride release from the giomer and compomer. It was found that the fluoride release from the subgroups of giomer and compomer was in the following order: fluoridated dentifrice twice daily > fluoridated dentifrice once daily + fluoridated mouthwash > fluoridated dentifrice once daily > control group. It was found that the giomer showed a greater fluoride uptake than the compomer.

Effects of an acid/alkaline treatment on the release of antioxidants and cellulose from different agro-food wastes.

Science.gov (United States)

Vadivel, Vellingiri; Moncalvo, Alessandro; Dordoni, Roberta; Spigno, Giorgia

2017-06-01

The present investigation was aimed to evaluate the release of both antioxidants and cellulosic fibre from different agro-food wastes. Cost-effective and easily available agro-food residues (brewers' spent grains, hazelnut shells, orange peels and wheat straw) were selected and submitted to a double-step acid/alkaline fractionation process. The obtained acid and alkaline liquors were analysed for total phenols content and antioxidant capacity. The final fibre residue was analysed for the cellulose, lignin and hemicellulose content. The total phenols content and antioxidant capacity of the acid liquors were higher than the alkaline hydrolysates. Orange peels and wheat straw gave, respectively, the highest (19.70±0.68mg/g dm ) and the lowest (4.70±0.29mg/g dm ) total phenols release. Correlation between antioxidant capacity of the liquors and their origin depended on the analytical assay used to evaluate it. All the acid liquors were also rich in sugar degradation products (mainly furfural). HPLC analysis revealed that the most abundant phenolic compound in the acid liquors was vanillin for brewers' spent grains, hazelnut shells and wheat straw, and p-hydroxybenzoic acid for orange peels. Wheat straw served as the best raw material for cellulose isolation, providing a final residue with a high cellulose content (84%) which corresponded to 45% of the original cellulose. The applied process removed more than 90% of the hemicellulose fraction in all the samples, while delignification degree ranged from 67% (in hazelnut shells), to 93% (in brewers' spent grains). It was not possible to select a unique raw material for the release of highest levels of both total phenols and cellulose. Copyright © 2017 Elsevier Ltd. All rights reserved.

SRTM Data Release for Africa, Colored Height

Science.gov (United States)

2004-01-01

This color shaded relief image shows the extent of digital elevation data for Africa recently released by the Shuttle Radar Topography Mission (SRTM). This release includes data for all of the continent, plus the island of Madagascar and the Arabian Peninsula. SRTM flew on board the Space Shuttle Endeavour in February 2000 and used an interferometric radar system to map the topography of Earth's landmass between latitudes 56 degrees south and 60 degrees north. The data were processed into geographic 'tiles,' each of which represents one by one degree of latitude and longitude. A degree of latitude measures 111 kilometers (69 miles) north-south, and a degree of longitude measures 111 kilometers or less east-west, decreasing away from the equator. The data are being released to the public on a continent-by-continent basis. This Africa segment includes 3256 tiles, almost a quarter of the total data set. Previous releases covered North America, South America and Eurasia. Forthcoming releases will include Australia plus an 'Islands' release for those islands not included in the continental releases. Together these data releases constitute the world's first high-resolution, near-global elevation model. The resolution of the publicly released data is three arcseconds (1/1,200 of a degree of latitude and longitude), which is about 90 meters (295 feet). Coverage in the current data release extends from 35 degrees north latitude at the southern edge of the Mediterranean to the very tip of South Africa, encompassing a great diversity of landforms. The northern part of the continent consists of a system of basins and plateaus, with several volcanic uplands whose uplift has been matched by subsidence in the large surrounding basins. Many of these basins have been infilled with sand and gravel, creating the vast Saharan lands. The Atlas Mountains in the northwest were created by convergence of the African and Eurasian tectonic plates. The geography of the central latitudes of

Nitrifying aerobic granular sludge fermentation for releases of carbon source and phosphorus: The role of fermentation pH.

Science.gov (United States)

Zou, Jinte; Pan, Jiyang; He, Hangtian; Wu, Shuyun; Xiao, Naidong; Ni, Yongjiong; Li, Jun

2018-07-01

The effect of fermentation pH (uncontrolled, 4 and 10) on the releases of carbon source and phosphorus from nitrifying aerobic granular sludge (N-AGS) was investigated. Meanwhile, metal ion concentration and microbial community characterization were explored during N-AGS fermentation. The results indicated that N-AGS fermentation at pH 10 significantly promoted the releases of soluble chemical oxygen demand (SCOD) and total volatile fatty acids (TVFAs). However, SCOD and TVFA released from N-AGS were inhibited at pH 4. Moreover, acidic condition promoted phosphorus release (mainly apatite) from N-AGS during anaerobic fermentation. Nevertheless, alkaline condition failed to increase phosphorus concentration due to the formation of chemical-phosphate precipitates. Compared with the previously reported flocculent sludge fermentation, N-AGS fermentation released more SCOD and TVFAs, possibly due to the greater extracellular polymeric substances content and some hydrolytic-acidogenic bacteria in N-AGS. Therefore, N-AGS alkaline fermentation facilitated the carbon source recovery, while N-AGS acidic fermentation benefited the phosphorus recovery. Copyright © 2018. Published by Elsevier Ltd.

21 CFR 181.28 - Release agents.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Release agents. 181.28 Section 181.28 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Release agents. Substances classified as release agents, when migrating from food-packaging material shall...

40 CFR 281.33 - Release detection.

Science.gov (United States)

2010-07-01

... equipped with release detection that detects a release within an hour by restricting or shutting off flow... designed to allow the contents of the pipe to drain back into the storage tank if the suction is released... UST systems must use interstitial monitoring within secondary containment of the tanks and the...

Measuring hypoxia induced metal release from highly contaminated estuarine sediments during a 40 day laboratory incubation experiment

Energy Technology Data Exchange (ETDEWEB)

Banks, Joanne L., E-mail: jlbanks@student.unimelb.edu.au [Department of Zoology, University of Melbourne, Victoria, 3010 Australia (Australia); Ross, D. Jeff, E-mail: Jeff.Ross@utas.edu.au [Institute of Marine and Antarctic Studies, Nubeena Crescent, Taroona, Tasmania, 7053 Australia (Australia); Keough, Michael J., E-mail: mjkeough@unimelb.edu.au [Department of Zoology, University of Melbourne, Victoria, 3010 Australia (Australia); Eyre, Bradley D., E-mail: bradley.eyre@scu.edu.au [Centre for Coastal Biogeochemistry, School of Environmental Science and Management, Southern Cross University, PO Box 157, Lismore, NSW, 2480 Australia (Australia); Macleod, Catriona K., E-mail: Catriona.Macleod@utas.edu.au [Institute of Marine and Antarctic Studies, Nubeena Crescent, Taroona, Tasmania, 7053 Australia (Australia)

2012-03-15

Nutrient inputs to estuarine and coastal waters worldwide are increasing and this in turn is increasing the prevalence of eutrophication and hypoxic and anoxic episodes in these systems. Many urbanised estuaries are also subject to high levels of anthropogenic metal contamination. Environmental O{sub 2} levels may influence whether sediments act as sinks or sources of metals. In this study we investigated the effect of an extended O{sub 2} depletion event (40 days) on fluxes of trace metals (and the metalloid As) across the sediment-water interface in sediments from a highly metal contaminated estuary in S.E. Tasmania, Australia. We collected sediments from three sites that spanned a range of contamination and measured total metal concentration in the overlying water using sealed core incubations. Manganese and iron, which are known to regulate the release of other divalent cations from sub-oxic sediments, were released from sediments at all sites as hypoxia developed. In contrast, the release of arsenic, cadmium, copper and zinc was comparatively low, most likely due to inherent stability of these elements within the sediments, perhaps as a result of their refractory origin, their association with fine-grained sediments or their being bound in stable sulphide complexes. Metal release was not sustained due to the powerful effect of metal-sulphide precipitation of dissolved metals back into sediments. The limited mobilisation of sediment bound metals during hypoxia is encouraging, nevertheless the results highlight particular problems for management in areas where hypoxia might occur, such as the release of metals exacerbating already high loads or resulting in localised toxicity. - Highlights: Black-Right-Pointing-Pointer Metal contaminated sediments exposed to long-term hypoxia released Mn and Fe pulses. Black-Right-Pointing-Pointer As flux increased under anoxic conditions Cd, Cu and Zn fluxes occurred only during the first week of hypoxia. Black

Measuring hypoxia induced metal release from highly contaminated estuarine sediments during a 40 day laboratory incubation experiment

International Nuclear Information System (INIS)

Banks, Joanne L.; Ross, D. Jeff; Keough, Michael J.; Eyre, Bradley D.; Macleod, Catriona K.

2012-01-01

Nutrient inputs to estuarine and coastal waters worldwide are increasing and this in turn is increasing the prevalence of eutrophication and hypoxic and anoxic episodes in these systems. Many urbanised estuaries are also subject to high levels of anthropogenic metal contamination. Environmental O 2 levels may influence whether sediments act as sinks or sources of metals. In this study we investigated the effect of an extended O 2 depletion event (40 days) on fluxes of trace metals (and the metalloid As) across the sediment–water interface in sediments from a highly metal contaminated estuary in S.E. Tasmania, Australia. We collected sediments from three sites that spanned a range of contamination and measured total metal concentration in the overlying water using sealed core incubations. Manganese and iron, which are known to regulate the release of other divalent cations from sub-oxic sediments, were released from sediments at all sites as hypoxia developed. In contrast, the release of arsenic, cadmium, copper and zinc was comparatively low, most likely due to inherent stability of these elements within the sediments, perhaps as a result of their refractory origin, their association with fine-grained sediments or their being bound in stable sulphide complexes. Metal release was not sustained due to the powerful effect of metal-sulphide precipitation of dissolved metals back into sediments. The limited mobilisation of sediment bound metals during hypoxia is encouraging, nevertheless the results highlight particular problems for management in areas where hypoxia might occur, such as the release of metals exacerbating already high loads or resulting in localised toxicity. - Highlights: ► Metal contaminated sediments exposed to long-term hypoxia released Mn and Fe pulses. ► As flux increased under anoxic conditions Cd, Cu and Zn fluxes occurred only during the first week of hypoxia. ► Flux of these metals from 3 sites was not related to total sediment metal

Total-System Performance Assessment for the Yucca Mountain Site

International Nuclear Information System (INIS)

Wilson, M.L.

2001-01-01

Yucca Mountain, Nevada, is under consideration as a potential site for a repository for high-level radioactive waste. Total-system performance-assessment simulations are performed to evaluate the safety of the site. Features, events, and processes have been systematically evaluated to determine which ones are significant to the safety assessment. Computer models of the disposal system have been developed within a probabilistic framework, including both engineered and natural components. Selected results are presented for three different total-system simulations, and the behavior of the disposal system is discussed. The results show that risk is dominated by igneous activity at early times, because the robust waste-package design prevents significant nominal (non-disruptive) releases for tens of thousands of years or longer. The uncertainty in the nominal performance is dominated by uncertainties related to waste-package corrosion at early times and by uncertainties in the natural system, most significantly infiltration, at late times

The tribology of metal-on-metal total hip replacements.

Science.gov (United States)

Scholes, S C; Unsworth, A

2006-02-01

Total hip surgery is an effective way of alleviating the pain and discomfort caused by diseased or damaged joints. However, in the majority of cases, these joints have a finite life. The main reason for failure is osteolysis (bone resorption). It is well documented that an important cause of osteolysis, and therefore the subsequent loosening and failure of conventional metal- or ceramic-on-ultra-high molecular weight polyethylene joints, is the body's immunological response to the polyethylene wear particles. To avoid this, interest has been renewed in metal-on-metal joints. The intention of this paper is to review the studies that have taken place within different laboratories to determine the tribological performance of new-generation metal-on-metal total hip replacements. These types of joint offer a potential solution to enhance the longevity of prosthetic hip systems; however, problems may arise owing to the effects of metal ion release, which are, as yet, not fully understood.

Anterior referencing of tibial slope in total knee arthroplasty considerably influences knee kinematics : a musculoskeletal simulation study

NARCIS (Netherlands)

Marra, Marco Antonio; Strzelczak, Marta; Heesterbeek, Petra J.C.; van de Groes, Sebastiaan A.W.; Janssen, Dennis W.; Koopman, Bart F.J.M.; Wymenga, Ate B.; Verdonschot, Nico J.J.

2017-01-01

Purpose: In total knee arthroplasty (TKA), the posterior tibial slope is not always reconstructed correctly, and the knee ligaments may become too tight in flexion. To release a tight flexion gap, surgeons can increase the posterior tibial slope using two surgical resection techniques: the anterior

32 CFR 635.10 - Release of information.

Science.gov (United States)

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Release of information. 635.10 Section 635.10 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) LAW ENFORCEMENT AND CRIMINAL INVESTIGATIONS LAW ENFORCEMENT REPORTING Release of Information § 635.10 Release of information. (a) Release of information from Army...

Bayesian inverse modeling and source location of an unintended 131I release in Europe in the fall of 2011

Science.gov (United States)

Tichý, Ondřej; Šmídl, Václav; Hofman, Radek; Šindelářová, Kateřina; Hýža, Miroslav; Stohl, Andreas

2017-10-01

In the fall of 2011, iodine-131 (131I) was detected at several radionuclide monitoring stations in central Europe. After investigation, the International Atomic Energy Agency (IAEA) was informed by Hungarian authorities that 131I was released from the Institute of Isotopes Ltd. in Budapest, Hungary. It was reported that a total activity of 342 GBq of 131I was emitted between 8 September and 16 November 2011. In this study, we use the ambient concentration measurements of 131I to determine the location of the release as well as its magnitude and temporal variation. As the location of the release and an estimate of the source strength became eventually known, this accident represents a realistic test case for inversion models. For our source reconstruction, we use no prior knowledge. Instead, we estimate the source location and emission variation using only the available 131I measurements. Subsequently, we use the partial information about the source term available from the Hungarian authorities for validation of our results. For the source determination, we first perform backward runs of atmospheric transport models and obtain source-receptor sensitivity (SRS) matrices for each grid cell of our study domain. We use two dispersion models, FLEXPART and Hysplit, driven with meteorological analysis data from the global forecast system (GFS) and from European Centre for Medium-range Weather Forecasts (ECMWF) weather forecast models. Second, we use a recently developed inverse method, least-squares with adaptive prior covariance (LS-APC), to determine the 131I emissions and their temporal variation from the measurements and computed SRS matrices. For each grid cell of our simulation domain, we evaluate the probability that the release was generated in that cell using Bayesian model selection. The model selection procedure also provides information about the most suitable dispersion model for the source term reconstruction. Third, we select the most probable location of

Bayesian inverse modeling and source location of an unintended 131I release in Europe in the fall of 2011

Directory of Open Access Journals (Sweden)

O. Tichý

2017-10-01

Full Text Available In the fall of 2011, iodine-131 (131I was detected at several radionuclide monitoring stations in central Europe. After investigation, the International Atomic Energy Agency (IAEA was informed by Hungarian authorities that 131I was released from the Institute of Isotopes Ltd. in Budapest, Hungary. It was reported that a total activity of 342 GBq of 131I was emitted between 8 September and 16 November 2011. In this study, we use the ambient concentration measurements of 131I to determine the location of the release as well as its magnitude and temporal variation. As the location of the release and an estimate of the source strength became eventually known, this accident represents a realistic test case for inversion models. For our source reconstruction, we use no prior knowledge. Instead, we estimate the source location and emission variation using only the available 131I measurements. Subsequently, we use the partial information about the source term available from the Hungarian authorities for validation of our results. For the source determination, we first perform backward runs of atmospheric transport models and obtain source-receptor sensitivity (SRS matrices for each grid cell of our study domain. We use two dispersion models, FLEXPART and Hysplit, driven with meteorological analysis data from the global forecast system (GFS and from European Centre for Medium-range Weather Forecasts (ECMWF weather forecast models. Second, we use a recently developed inverse method, least-squares with adaptive prior covariance (LS-APC, to determine the 131I emissions and their temporal variation from the measurements and computed SRS matrices. For each grid cell of our simulation domain, we evaluate the probability that the release was generated in that cell using Bayesian model selection. The model selection procedure also provides information about the most suitable dispersion model for the source term reconstruction. Third, we select the most

Volatiles and energy released by Puracé volcano

Science.gov (United States)

Maldonado, Luisa Fernanda Meza; Inguaggiato, Salvatore; Jaramillo, Marco Tulio; Valencia, Gustavo Garzón; Mazot, Agnes

2017-12-01

Total CO2 output of Puracé volcano (Colombia) was estimated on the basis of fluids discharged by fumaroles, soil gases, and dissolved carbon species in the aquifer. The soil CO2 emission was computed from a field survey of 512 points of CO2 soil flux measurements at the main degassing areas of Puracé volcano. The CO2 flux from Puracé's plume was estimated using an indirect method, that used the SO2 plume flux and CO2/SO2 ratio of the main high temperature fumarole. The total output of CO2 was estimated at ≅ 1500 t/day. The main contribution of CO2 comes from the plume (summit degassing) and from soil degassing that emit 673 and 812 t/day, respectively. The contributions of summit and soil degassing areas are comparable, indicating an intermediate degassing style partitioned between closed and open conduit systems. The estimated water vapor discharge (as derived from the chemical composition of the fumaroles, the H2O/CO2 ratio, and the SO2 plume flux) allowed calculation of the total thermal energy (fumarolic, soil degassing, and aquifer) released from the Puracé volcanic system. This was 360 MW.

133Xe release during post-irradiation annealing of uranium metal in the presence of a constant volume of air Pt. 1

International Nuclear Information System (INIS)

Marei, S.A.; El-Garhy, M.; El-Bayoumy, S.; Muenze, R.; Hladik, O.

1978-01-01

The fractional release of 133 Xe at different temperatures was studied as a function of time in the presence of air during post-irradiation annealing of uranium metal. The relation between the fractional release and tsup(1/2) was found to be irregular. There is an initial step in the annealing curves (at the temperature range of 400-710 deg C) which decreases by increasing temperature and totally disappears at the high temperature of 800-1000 deg C. The initial step was found to be due to the surface oxidation of uranium metal. The other two parts of the release curves are normal for 133 Xe release from uranium metal. Since in this work the irradiation temperature is low ( 133 Xe. (T.G.)

Doses of controlled-release fertilizer for production of rubber tree rootstocks

Directory of Open Access Journals (Sweden)

Renato Luis Grisi Macedo

2012-06-01

Full Text Available This experimental study aimed to evaluate the effects of doses of controlled-release fertilizer (ALL on the development of rubber tree rootstocks. The fertilizer used was Osmocote®, scheduled to be released for 8-9 months and with the following composition: N (15%, P2O5 (9%, K2O (12%, Mg (1%, S (2.3%, B (0.02%, Cu (0.05%, Fe (1%, Mn (0.06%, Mo (0.02% and Zn (0.05%. A randomized block design was used, with four treatments and eight replicates of 20 plants per plot. The controlled-release fertilizer was added to Rendimax Floreira® substrate at doses of 0, 3, 6 and 9 g per liter, and rootstocks were produced in plastic containers with a capacity of two liters of substrate. Three seeds of clone GT 1 were scattered in each container and thinning was performed on day 60, leaving the most vigorous plant only. After the fourth leaf shot from each rootstock, the containers of each treatment were topped, due to compaction, with 300 mL of the relevant fertilizer and substrate mixture. The rootstocks were evaluated at eight months of age as to height, stem diameter (DC 5 cm above root collar, total dry matter, shoot and root dry matter, leaf nutrient levels and percentage of plants suitable for grafting (DC≥1.0 cm. Results revealed that adequate development and nutrition of rootstocks was achieved by using 6 g of controlled-release fertilizer per liter of substrate.

Drug Release Studies from Caesalpinia pulcherrima Seed Polysaccharide.

Science.gov (United States)

Jeevanandham, Somasundaram; Dhachinamoorthi, Duraiswamy; Bannoth Chandra Sekhar, Kothapalli

2011-01-01

This study examines the controlled release behavior of both water-soluble (acetaminophen, caffeine, theophylline and salicylic acid) and water insoluble (indomethacin) drugs derived from Caesalpinia pulcherrima seed Gum isolated from Caesalpinia pulcherrima kernel powder. It further investigates the effect of incorporating diluents such as microcrystalline cellulose and lactose on caffeine release. In addition the effect the gum's (polysaccharide) partial cross-linking had on release of acetaminophen was examined. Applying the exponential equation, the soluble drugs mechanism of release was found to be anomalous. The insoluble drugs showed a near case II or zero order release mechanism. The rate of release in descending order was caffeine, acetaminophen, theophylline, salicylic acid and indomethacin. An increase in the release kinetics of the drug was observed on blending with diluents. However, the rate of release varied with the type and amount of blend within the matrix. The mechanism of release due to effect of diluents was found to be anomalous. The rate of drug release decreased upon partial cross-linking and the mechanism of release was found to be of super case II.

Gliclazide directly inhibits arginine-induced glucagon release

DEFF Research Database (Denmark)

Cejvan, Kenan; Coy, David H; Holst, Jens Juul

2002-01-01

Arginine-stimulated insulin and somatostatin release is enhanced by the sulfonylurea gliclazide. In contrast, gliclazide inhibits the glucagon response. The aim of the present study was to investigate whether this inhibition of glucagon release was mediated by a direct suppressive effect of glicl......Arginine-stimulated insulin and somatostatin release is enhanced by the sulfonylurea gliclazide. In contrast, gliclazide inhibits the glucagon response. The aim of the present study was to investigate whether this inhibition of glucagon release was mediated by a direct suppressive effect....... In islet perifusions with DC-41-33, arginine-induced glucagon release was inhibited by 66%. We therefore concluded that gliclazide inhibits glucagon release by a direct action on the pancreatic A cell....

Relationship between insulin release and 65zinc efflux from rat pancreatic islets maintained in tissue culture

International Nuclear Information System (INIS)

Formby, B.; Schmid-Formby, F.; Grodsky, G.M.

1984-01-01

In short-term batch-incubation or perfusion experiments, we studied insulin release and associated 65 Zn efflux from rat pancreatic islets loaded with 65 Zn by 24-h tissue culture in low-glucose medium. The fractional basal insulin release and 65 Zn efflux were 0.4% and 3% of total content/h/islet, respectively. Thus, basal 65 Zn efflux was much greater than that to be accounted for if zinc was released proportionally with insulin release only; extragranular zinc flux was suggested. Two millimolar glucose, with or without 1 mM 3-isobutyl-1-methylxanthine (IBMX), affected neither insulin release nor associated 65 Zn efflux. Twenty-five millimolar glucose produced a significant threefold increase in insulin release above baseline, but somewhat decreased 65 Zn efflux at marginal significance. Glucose (25 mM) plus 1 mM IBMX provoked a high increase in insulin release and an associated 30% increase in fractional 65 Zn efflux over basal. Calculations based on previous estimations of 65 Zn distribution and equilibrium with islet zinc indicated that molar zinc efflux was more than sufficient to account for a 2-zinc-insulin hexamer. L-Leucine (2 or 20 mM) plus 1 mM IBMX caused far greater 65 Zn efflux for the amount of insulin released, indicating additional 65 Zn mobilization not directly related to insulin secretion. To evaluate 65 Zn efflux during inhibited insulin secretion, batch incubations were performed in 100% D 2 O or at 27 degrees C, conditions that inhibited insulin release stimulated by high glucose plus IBMX. These agents decreased the 65 Zn efflux far below the basal value (35% and 50%, respectively) and greater than could be accounted for by the attendent inhibition of insulin secretion.(ABSTRACT TRUNCATED AT 250 WORDS)

On the experimental approaches for the assessment of the release of engineered nanomaterials from nanocomposites by physical degradation processes

International Nuclear Information System (INIS)

Blázquez, M; Unzueta, I; Egizabal, A

2014-01-01

The LIFE+ Project SIRENA, Simulation of the release of nanomaterials from consumer products for environmental exposure assessment, (LIFE11 ENV/ES/596) has set up a Technological Surveillance System (TSS) to trace technical references at worldwide level related to nanocomposites and the release from nanocomposites. So far a total of seventy three items of different nature (from peer reviewed articles to presentations and contributions to congresses) have been selected and classified as n anomaterials release simulation technologies . In present document, different approaches for the simulation of different life cycle stages through the physical degradation of polymer nanocomposites at laboratory scale are assessed. In absence of a reference methodology, the comparison of the different protocols used still remains a challenge

On the experimental approaches for the assessment of the release of engineered nanomaterials from nanocomposites by physical degradation processes

Science.gov (United States)

Blázquez, M.; Egizabal, A.; Unzueta, I.

2014-08-01

The LIFE+ Project SIRENA, Simulation of the release of nanomaterials from consumer products for environmental exposure assessment, (LIFE11 ENV/ES/596) has set up a Technological Surveillance System (TSS) to trace technical references at worldwide level related to nanocomposites and the release from nanocomposites. So far a total of seventy three items of different nature (from peer reviewed articles to presentations and contributions to congresses) have been selected and classified as "nanomaterials release simulation technologies". In present document, different approaches for the simulation of different life cycle stages through the physical degradation of polymer nanocomposites at laboratory scale are assessed. In absence of a reference methodology, the comparison of the different protocols used still remains a challenge.

Quality assessment of the Ozone_cci Climate Research Data Package (release 2017 – Part 1: Ground-based validation of total ozone column data products

Directory of Open Access Journals (Sweden)

K. Garane

2018-03-01

Full Text Available The GOME-type Total Ozone Essential Climate Variable (GTO-ECV is a level-3 data record, which combines individual sensor products into one single cohesive record covering the 22-year period from 1995 to 2016, generated in the frame of the European Space Agency's Climate Change Initiative Phase II. It is based on level-2 total ozone data produced by the GODFIT (GOME-type Direct FITting v4 algorithm as applied to the GOME/ERS-2, OMI/Aura, SCIAMACHY/Envisat and GOME-2/Metop-A and Metop-B observations. In this paper we examine whether GTO-ECV meets the specific requirements set by the international climate–chemistry modelling community for decadal stability long-term and short-term accuracy. In the following, we present the validation of the 2017 release of the Climate Research Data Package Total Ozone Column (CRDP TOC at both level 2 and level 3. The inter-sensor consistency of the individual level-2 data sets has mean differences generally within 0.5 % at moderate latitudes (±50°, whereas the level-3 data sets show mean differences with respect to the OMI reference data record that span between −0.2 ± 0.9 % (for GOME-2B and 1.0 ± 1.4 % (for SCIAMACHY. Very similar findings are reported for the level-2 validation against independent ground-based TOC observations reported by Brewer, Dobson and SAOZ instruments: the mean bias between GODFIT v4 satellite TOC and the ground instrument is well within 1.0 ± 1.0 % for all sensors, the drift per decade spans between −0.5 % and 1.0 ± 1.0 % depending on the sensor, and the peak-to-peak seasonality of the differences ranges from ∼ 1 % for GOME and OMI to  ∼ 2 % for SCIAMACHY. For the level-3 validation, our first goal was to show that the level-3 CRDP produces findings consistent with the level-2 individual sensor comparisons. We show a very good agreement with 0.5 to 2 % peak-to-peak amplitude for the monthly mean difference time series and a

Predicting hydrocarbon release from soil

International Nuclear Information System (INIS)

Poppendieck, D.; Loehr, R.C.

2002-01-01

'Full text:' The remediation of hazardous chemicals from soils can be a lengthy and costly process. As a result, recent regulatory initiatives have focused on risk-based corrective action (RBCA) approaches. Such approaches attempt to identify the amount of chemical that can be left at a site with contaminated soil and still be protective of human health and the environment. For hydrocarbons in soils to pose risk to human heath and the environment, the hydrocarbons must be released from the soil and accessible to microorganisms, earthworms, or other higher level organisms. The sorption of hydrocarbons to soil can reduce the availability of the hydrocarbon to receptors. Typically in soils and sediments, there is an initial fast release of a hydrocarbon from the soil to the aqueous phase followed by a slower release of the remaining hydrocarbon to the aqueous phase. The rate and extent of slow release can influence aqueous hydrocarbon concentrations and the fate and transport of hydrocarbons in the subsurface. Once the fast fraction of the chemical has been removed from the soil, the remaining fraction of a chemical may desorb at a rate that natural mechanisms can attenuate the released hydrocarbon. Hence, active remediation may be needed only until the fast fraction has been removed. However, the fast fraction is a soil and chemical specific parameter. This presentation will present a tier I type protocol that has been developed to quickly estimate the fraction of hydrocarbons that are readily released from the soil matrix to the aqueous phase. Previous research in our laboratory and elsewhere has used long-term desorption (four months) studies to determine the readily released fraction. This research shows that a single short-term (less than two weeks) batch extraction procedure provides a good estimate of the fast released fraction derived from long-term experiments. This procedure can be used as a tool to rapidly evaluate the release and bioavailability of

Pressure releasing device for reactor container

International Nuclear Information System (INIS)

Takeda, Mika.

1994-01-01

In the present invention, dose rate to public caused by radioactive rare gases can be decreased. That is, a reactor container contains a reactor pressure vessel incorporating a reactor core. There are disposed a pressure releasing system for releasing the pressure in the reactor pressure vessel to the outside, and a burning device for burning gases released from the pressure releasing system. An exhaustion pipe is disposed to the pressure releasing system. A burning device is disposed to the exhaustion pipe. It is effective to dispose a ventilation port at a portion of the exhaustion pipe upstream of the burning device. In addition, the burning device may preferably be disposed in a multi-stage in the axial direction of the exhaustion pipe. With such procedures, hydrogen in gases discharged along with the release of the pressure in the container is burned. Buoyancy is caused to the exhaustion gases by heat energy upon burning. Since the exhaustion gases can reach a higher level by the buoyancy, the dose rate due to the rare gases can be reduced. (I.S.)

Comparison of the regulatory models assessing off-site radiological dose due to the routine releases of tritium

International Nuclear Information System (INIS)

Hwang, W. T.; Kim, E. H.; Han, M. H.; Choi, Y. H.; Lee, H. S.; Lee, C. W.

2005-01-01

Methodologies of NEWTRIT model, NRC model and AIRDOS-EPA model, which are off-site dose assessment models for regulatory compliance from routine releases of tritium into the environment, were investigated. Using the domestic data, if available, the predictive results of the models were compared. Among them, recently developed NEWTRIT model considers only doses from organically bounded tritium (OBT) due to environmental releases of tritiated water (HTO). A total dose from all exposure pathways predicted from AIRDOS-EPA model was 1.03 and 2.46 times higher than that from NEWTRIT model and NRC model, respectively. From above result, readers should not have an understanding that a predictive dose from NRC model may be underestimated compared with a realistic dose. It is because of that both mathematical models and corresponding parameter values for regulatory compliance are based on the conservative assumptions. For a dose by food consumption predicted from NEWTRIT model, the contribution of OBT was nearly equivalent to that of HTO due to relatively high consumption of grains in Korean. Although a total dose predicted from NEWTRIT model is similar to that from AIRDOS-EPA model, NEWTRIT model may be have a meaning in the understanding of phenomena for the behavior of HTO released into the environment

Correlation between bulk- and surface chemistry of Cr-tanned leather and the release of Cr(III) and Cr(VI)

Energy Technology Data Exchange (ETDEWEB)

Hedberg, Yolanda S., E-mail: yolanda@kth.se [KTH Royal Institute of Technology, School of Chemical Science and Engineering, Department of Chemistry, Division of Surface and Corrosion Science, SE-10044 Stockholm (Sweden); Institute of Environmental Medicine, Karolinska Institutet, Box 210, SE-17177 Stockholm (Sweden); Lidén, Carola, E-mail: carola.liden@ki.se [Institute of Environmental Medicine, Karolinska Institutet, Box 210, SE-17177 Stockholm (Sweden); Odnevall Wallinder, Inger, E-mail: ingero@kth.se [KTH Royal Institute of Technology, School of Chemical Science and Engineering, Department of Chemistry, Division of Surface and Corrosion Science, SE-10044 Stockholm (Sweden)

2014-09-15

Graphical abstract: - Highlights: • Released reducing/complexing leather-specific species can reduce released Cr(VI). • No co-released species enable the formation of Cr(VI) in solution. • The major Cr species released from leather in phosphate buffer was Cr(III) (>82%). • No Cr(VI) was released into artificial sweat. - Abstract: About 1–3% of the adult general population in Europe is allergic to chromium (Cr). The assessment of the potential release of Cr(III) and Cr(VI) from leather is hence important from a human health and environmental risk perspective. The Cr(VI) content in leather was recently restricted in the European Union. The aim of this study was to assess possible correlations between the bulk and surface chemistry of leather, released Cr(III) and Cr(VI), and capacities of co-released leather specific species to reduce and complex released Cr. Four differently tanned leathers were characterized by scanning electron microscopy with energy dispersive spectroscopy, X-ray photoelectron spectroscopy, attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, and the diphenylcarbazide colorimetric method. Their characteristics were compared with results on Cr(III) and Cr(VI) release into artificial sweat (ASW, pH < 6.5) and phosphate buffer (PB, pH 7.5–8.0), measured by means of spectrophotometry and atomic absorption spectroscopy. Co-released leather-specific species were shown to reduce Cr(VI), both in ASW and in PB. Their reduction capacities correlated with findings of the surface content of Cr and of released Cr. Leather samples without this capacity, and with less aromatic surface groups visible by ATR-FTIR, revealed Cr(VI) both at the surface and in solution (PB)

Design and evaluation of nicorandil extended-release tablet

Directory of Open Access Journals (Sweden)

Ju-Young Kim

2015-04-01

Full Text Available The aim of this study was to design and evaluate extended-release formulations of a model drug, nicorandil, in order to achieve the desired steady-state plasma concentration of drug in vivo. Simulation was employed to estimate optimum dissolution and absorption rate of nicorandil. The dissolution test was employed using pH 1.2, 4.0, 6.8 buffer solution, or water, to measure the in vitro release behaviors of nicorandil formulations. A single dose (15 mg of each formulation was orally administered to four beagle dogs under fasted conditions, and the pharmacokinetic parameters were calculated. The in vitro/in vivo relationship of the extended-release formulation was confirmed using in vitro dissolution profiles and plasma concentrations of drug in beagle dogs. Nicorandil was released completely within 30 min from the immediate-release tablets and released for 24 h from the extended-release tablets. The nicorandil plasma concentration could be modified by adjusting the drug release rate from the extended-release formulation. The release rate of nicorandil was the rate-limiting step in the overall absorption of drug from the extended-release formulations. These results highlight the potential of a nicorandil extended-release formulation in the treatment of angina pectoris.

21 CFR 178.3860 - Release agents.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Release agents. 178.3860 Section 178.3860 Food and... and Production Aids § 178.3860 Release agents. Substances listed in paragraph (b) of this section may be safely used as release agents in petroleum wax complying with § 178.3710 and in polymeric resins...

Silver speciation and characterization of nanoparticles released from plastic food containers by single particle ICPMS.

Science.gov (United States)

Ramos, K; Gómez-Gómez, M M; Cámara, C; Ramos, L

2016-05-01

Silver migration from a commercial baby feeding bottle and a food box containing AgNPs, as confirmed by SEM-EDX analysis, was evaluated using food simulant solutions [i.e., water, 3% (v/v) acetic acid, and 10% and 90% (v/v) ethanol]. Silver release was investigated at temperatures in the 20-70°C range using contact times of up to 10 days. Migration of silver from the food box was in all cases 2 to 3 orders of magnitude higher than that observed for the baby bottle, although the total silver content in the original box material was half of that found in the baby bottle. As expected, for both food containers, silver migration depended on both the nature of the tested solution and the applied conditions. The highest release was observed for 3% acetic acid at 70°C for 2h, corresponding to 62ngdm(2) and 1887ngdm(-2) of silver for the baby bottle and the food box, respectively. Single particle-inductively coupled plasma mass spectrometry (SP-ICPMS) was used to characterise and quantify AgNPs in the food simulants extracts. Sample preparation was optimized to preserve AgNPs integrity. The experimental parameters affecting AgNPs detection, sizing and quantification by SP-ICPMS were also optimised. Analyses of water and acidic extracts revealed the presence of both dissolved silver and AgNPs. Small AgNPs (in the 18-30nm range) and particle number concentrations within the 4-1510 10(6)L(-1) range were detected, corresponding to only 0.1-8.6% of the total silver released from these materials. The only exception was AgNPs migrated into water at 40°C and 70°C from the food box, which accounted for as much as 34% and 69% of the total silver content, respectively. Copyright © 2016 Elsevier B.V. All rights reserved.

The functional dependence of the total hazard from an air pollution incidence on the environmental parameters

International Nuclear Information System (INIS)

Skibin, D.

1980-01-01

A general case of release to the atmosphere of a pollutant is considered. In hazards evaluation the processes involved are usually estimated conservatively so as to maximize the computed doses. The present work helps to identify the worst cases. In addition, a model of the total dose is presented and its variations are studied as a function of wind speed, deposition velocity and source height. The value of each parameter giving the highest total dose as a function of the model's parameters is determined. (H.K.)

Air modelling as an alternative to sampling for low-level radioactive airborne releases

International Nuclear Information System (INIS)

Morgenstern, M.Y.; Hueske, K.

1995-01-01

This paper describes our efforts to assess the effect of airborne releases at one DOE laboratory using air modelling based on historical data. Among the facilities affected by these developments is Los Alamos National Laboratory (LANL) in New Mexico. RCRA, as amended by the Hazardous and Solid Waste Amendments (HSWA) in 1984, requires all facilities which involve the treatment, storage, and disposal of hazardous waste obtain a RCRA/HSWA waste facility permit. LANL complied with CEARP by initiating a process of identifying potential release sites associated with LANL operations prior to filing a RCRA/HSWA permit application. In the process of preparing the RCRA/HSWA waste facility permit application to the U.S. Environmental Protection Agency (EPA), a total of 603 Solid Waste Management Units (SWMUs) were identified as part of the requirements of the HSWA Module VIH permit requirements. The HSWA Module VIII permit requires LANL to determine whether there have been any releases of hazardous waste or hazardous constituents from SWMUs at the facility dating from the 1940's by performing a RCRA Facility Investigation to address known or suspected releases from specified SWMUs to affected media (i.e. soil, groundwater, surface water, and air). Among the most troublesome of the potential releases sites are those associated with airborne radioactive releases. In order to assess health risks associated with radioactive contaminants in a manner consistent with exposure standards currently in place, the DOE and LANL have established Screening Action Levels (SALs) for radioactive soil contamination. The SALs for each radionuclide in soil are derived from calculations based on a residential scenario in which individuals are exposed to contaminated soil via inhalation and ingestion as well as external exposure to gamma emitters in the soil. The applicable SALs are shown

Sellafield (release of radioactivity)

Energy Technology Data Exchange (ETDEWEB)

Cunningham, J; Goodlad, A; Morris, M

1986-02-06

A government statement is reported, about the release of plutonium nitrate at the Sellafield site of British Nuclear Fuels plc on 5 February 1986. Matters raised included: details of accident; personnel monitoring; whether radioactive material was released from the site; need for public acceptance of BNFL activities; whether plant should be closed; need to reduce level of radioactive effluent; number of incidents at the plant.

Lateral Cricoarytenoid Release: Development of a Novel Surgical Treatment Option for Adductor Spasmodic Dysphonia in a Canine Laryngeal Model.

Science.gov (United States)

Park, Andrea M; Paniello, Randal C

2016-09-01

To investigate the efficacy of a novel adductor muscle-releasing technique designed to decrease the force of vocal fold adduction, as a potential surgical therapy for patients with adductor spasmodic dysphonia (ADSD). Experimental animal study. A canine laryngeal model was used to assess the acute and sustained efficacy of a lateral cricoarytenoid (LCA) muscle release. A total of 34 canine hemilaryngeal preparations were divided among 7 experimental groups. The LCA muscle was separated from its cricoid cartilage origin via an open, anterior, submucosal approach. The laryngeal adductory pressures (LAP) were assessed pre- and post-muscle release via direct recurrent laryngeal nerve stimulation. Measurements were repeated at 1.5, 3, or 6 months postoperatively. Another study evaluated release of the thyroarytenoid (TA) muscle from its thyroid cartilage origin. Releasing the LCA muscle demonstrated a significant decrease in LAP acutely and was maintained at all 3 time points with the aid of a barrier (P < .05). Without the barrier, the LCA muscle reattached to the cricoid. Acute release of the TA muscle did not significantly decrease the LAP. The proposed LCA release procedure may provide patients with a permanent treatment option for ADSD. However, longer-term studies and human trials are needed. © The Author(s) 2016.

Antimony leaching release from brake pads: Effect of pH, temperature and organic acids.

Science.gov (United States)

Hu, Xingyun; He, Mengchang; Li, Sisi

2015-03-01

Metals from automotive brake pads pollute water, soils and the ambient air. The environmental effect on water of antimony (Sb) contained in brake pads has been largely untested. The content of Sb in one abandoned brake pad reached up to 1.62×10(4) mg/kg. Effects of initial pH, temperature and four organic acids (acetic acid, oxalic acid, citric acid and humic acid) on Sb release from brake pads were studied using batch reactors. Approximately 30% (97 mg/L) of the total Sb contained in the brake pads was released in alkaline aqueous solution and at higher temperature after 30 days of leaching. The organic acids tested restrained Sb release, especially acetic acid and oxalic acid. The pH-dependent concentration change of Sb in aqueous solution was best fitted by a logarithmic function. In addition, Sb contained in topsoil from land where brake pads were discarded (average 9×10(3) mg/kg) was 3000 times that in uncontaminated soils (2.7±1 mg/kg) in the same areas. Because potentially high amounts of Sb may be released from brake pads, it is important that producers and environmental authorities take precautions. Copyright © 2015. Published by Elsevier B.V.

Site release in the decommissioning of nuclear installations

International Nuclear Information System (INIS)

Revilla, Jose Luis; Sanz, Maria Teresa; Marugan, Inmaculada; Simon, Inmaculada; Martin, Manuel; Solis, Susana; Sterling, Agustina

2008-01-01

Spanish regulatory framework for the decommissioning process of a nuclear facility ends up with a decommission statement, which releases the licence-holder of the facility from its responsibilities as an operator. It also establishes -where a restricted site release applies- the appropriate future use restrictions, and the responsible of both maintaining such restrictions and ensuring their compliance. Releasing a site implies eliminating all radiological monitoring. The Regulations, however, did not specify either the radiological conditions to be met for the site to be released, or the possibility of a partial release -with or without restrictions-. In case of restricted site release, the Regulations did not specify either the required criteria for such a release. This paper presents the main features of the Safety Instruction IS-13 'Radiological criteria for the release of nuclear facilities sites' issued recently by the Spanish Nuclear Safety Council as a new specific regulation. This Safety Instruction establishes the requirements and conditions for the release of nuclear facility sites, that is, radiological criteria on the effective dose to the public, partial release of nuclear facility sites and restricted release of nuclear facility sites. (author).

Alveolar macrophage release of tumor necrosis factor-alpha in chronic alcoholics without liver disease.

Science.gov (United States)

Omidvari, K; Casey, R; Nelson, S; Olariu, R; Shellito, J E

1998-05-01

Alcohol is an immunosuppressive drug, and chronic abuse has been associated with increased susceptibility to a variety of infections, including bacterial pneumonia and tuberculosis. Alveolar macrophages are the resident phagocytes of the lung and play a central role in lung host defenses against infection ranging from direct antibacterial activity to the release of proinflammatory cytokines such as tumor necrosis factor-alpha (TNFalpha). TNFalpha, in particular, plays a key role in the development of the early inflammatory response. In this study, we investigated the effects of chronic alcohol consumption on alveolar macrophage release of TNFalpha in vitro. We prospectively studied lipopolysaccharide (LPS)-stimulated release of TNFalpha from alveolar macrophages obtained from bronchoalveolar lavage fluid (BALF) in 22 alcoholic (18 smokers, 4 nonsmokers) and 7 nondrinking healthy volunteers (3 smokers, 4 nonsmokers). The total number of cells recovered by bronchoalveolar lavage (BAL) and their differential distribution were not significantly different in alcoholics versus controls (43 +/- 8 x 10(6) and 39 +/- 13 x 10(6), respectively). However, the total number of cells recovered from BALF was significantly higher in smokers (51 +/- 8 x 10(6)) than in nonsmokers (19 +/- 5 x 10(6)). Spontaneous (basal) release of TNFalpha by alveolar macrophages was the same in alcoholics and controls. In contrast, LPS-stimulated release of TNFalpha was significantly suppressed in alcoholics compared with that of controls (1343 +/- 271 vs. 3806 +/- 926 U TNF/ml/10(6) cells, respectively, p < 0.015). When controlled for smoking, LPS-stimulated TNFalpha production was suppressed in alcoholic nonsmokers (563 +/- 413 U TNF/ml/10(6)) compared with control nonsmokers (5113 +/- 1264 U TNF/ml/10(6)). LPS-stimulated TNFalpha production was also less in control smokers (2063 +/- 386 U TNF/ml/10(6) cells) than in control nonsmokers (5113 +/- 1264 U TNF/ml/10(6) cells). There was no difference

Controlled drug release for tissue engineering.

Science.gov (United States)

Rambhia, Kunal J; Ma, Peter X

2015-12-10

Tissue engineering is often referred to as a three-pronged discipline, with each prong corresponding to 1) a 3D material matrix (scaffold), 2) drugs that act on molecular signaling, and 3) regenerative living cells. Herein we focus on reviewing advances in controlled release of drugs from tissue engineering platforms. This review addresses advances in hydrogels and porous scaffolds that are synthesized from natural materials and synthetic polymers for the purposes of controlled release in tissue engineering. We pay special attention to efforts to reduce the burst release effect and to provide sustained and long-term release. Finally, novel approaches to controlled release are described, including devices that allow for pulsatile and sequential delivery. In addition to recent advances, limitations of current approaches and areas of further research are discussed. Copyright © 2015 Elsevier B.V. All rights reserved.

Release of Phosphorus Forms from Cover Crop Residues in Agroecological No-Till Onion Production

Directory of Open Access Journals (Sweden)

Rodolfo Assis de Oliveira

Full Text Available ABSTRACT Cover crops grown alone or in association can take up different amounts of phosphorus (P from the soil and accumulate it in different P-forms in plant tissue. Cover crop residues with a higher content of readily decomposed forms may release P more quickly for the next onion crop. The aim of this study was to evaluate the release of P forms from residues of single and mixed cover crops in agroecological no-till onion (Allium cepa L. production. The experiment was conducted in Ituporanga, Santa Catarina (SC, Brazil, in an Inceptisol, with the following treatments: weeds, black oat (Avena sativa L., rye (Secale cereale L., oilseed radish (Raphanus sativus L., oilseed radish + black oat, and oilseed radish + rye. Cover crops were sown in April 2013. In July 2013, plant shoots were cut close to the soil surface and part of the material was placed in litterbags. The bags were placed on the soil surface and residues were collected at 0, 15, and 45 days after deposition (DAD. Residues were dried and ground and P in the plant tissue was determined through chemical fractionation. The release of P contained in the tissue of cover crops depends not only on total P content in the tissue, but also on the accumulation of P forms and the quality of the residue in decomposition. The highest accumulation of P in cover crops occurred in the soluble inorganic P fraction, which is the fraction of fastest release in plants. Black oat had the highest initial release rate of soluble inorganic P, which became equal to the release rate of other cover crop residues at 45 DAD. Weeds released only half the amount of soluble inorganic P in the same period, despite accumulating a considerable amount of P in their biomass. The mixtures of oilseed radish + rye and oilseed radish + black oat showed higher release of P associated with RNA at 45 DAD in comparison to the single treatments.

Investigation of delayed fission gas release

International Nuclear Information System (INIS)

Cayet, Nicolas

1996-05-01

The study of the fission gas release process in the high burnup rig IFA-562 has revealed a particular fuel behaviour: a delay in the fission gas release process. It appeared that an important release of gas was measured by the pressure transducers once the power had decreased, whereas, during steady-state operation, the pressure did not increase very much. After examinations, the gap size has been concluded to be the main parameter involving this delay. However the burnup could have been a potential factor, its role is mainly to close the gap by swelling. The observations of low burnup rods have shown the same delayed fission gas release, the gap being small by design and closed essentially by thermal expansion. The study of the kinetics has demonstrated the time-independency of the phenomenon. Thus the proposed mechanism driving this delayed fission gas release would involve three consecutives stages. During steady-state, the gas is released into the interlinkage network of grain boundary bubbles and cracks. Due to the closed gap, the gas is trapped in some void volumes, unable to escape the pellet. During power reduction, the gap and some old/new cracks open, immediately providing a path for the gas to the pressure transducers and explaining this delay in the fission gas release. (author)

Aβ42 oligomers selectively disrupt neuronal calcium release.

Science.gov (United States)

Lazzari, Cristian; Kipanyula, Maulilio J; Agostini, Mario; Pozzan, Tullio; Fasolato, Cristina

2015-02-01

Accumulation of amyloid-β (Aβ) peptides correlates with aging and progression of Alzheimer's disease (AD). Aβ peptides, which cause early synaptic dysfunctions, spine loss, and memory deficits, also disturb intracellular Ca(2+) homeostasis. By cytosolic and endoplasmic reticulum Ca(2+) measurements, we here define the short-term effects of synthetic Aβ42 on neuronal Ca(2+) dynamics. When applied acutely at submicromolar concentration, as either oligomers or monomers, Aβ42 did not cause Ca(2+) release or Ca(2+) influx. Similarly, 1-hour treatment with Aβ42 modified neither the resting cytosolic Ca(2+) level nor the long-lasting Ca(2+) influx caused by KCl-induced depolarization. In contrast, Aβ42 oligomers, but not monomers, significantly altered Ca(2+) release from stores with opposite effects on inositol 1,4,5-trisphosphate (IP3)- and caffeine-induced Ca(2+) mobilization without alteration of the total store Ca(2+) content. Ca(2+) dysregulation by Aβ42 oligomers involves metabotropic glutamate receptor 5 and requires network activity and the intact exo-endocytotic machinery, being prevented by tetrodotoxin and tetanus toxin. These findings support the idea that Ca(2+) store dysfunction is directly involved in Aβ42 neurotoxicity and represents a potential therapeutic target in AD-like dementia. Copyright © 2015 Elsevier Inc. All rights reserved.

Controlled release system for ametryn using polymer microspheres: Preparation, characterization and release kinetics in water

International Nuclear Information System (INIS)

Grillo, Renato; Pereira, Anderson do Espirito Santo; Ferreira Silva de Melo, Nathalie; Porto, Raquel Martins; Feitosa, Leandro Oliveira; Tonello, Paulo Sergio; Dias Filho, Newton L.; Rosa, Andre Henrique; Lima, Renata; Fraceto, Leonardo Fernandes

2011-01-01

The purpose of this work was to develop a modified release system for the herbicide ametryn by encapsulating the active substance in biodegradable polymer microparticles produced using the polymers poly(hydroxybutyrate) (PHB) or poly(hydroxybutyrate-valerate) (PHBV), in order to both improve the herbicidal action and reduce environmental toxicity. PHB or PHBV microparticles containing ametryn were prepared and the efficiencies of herbicide association and loading were evaluated, presenting similar values of approximately 40%. The microparticles were characterized by scanning electron microscopy (SEM), which showed that the average sizes of the PHB and PHBV microparticles were 5.92 ± 0.74 μm and 5.63 ± 0.68 μm, respectively. The ametryn release profile was modified when it was encapsulated in the microparticles, with slower and more sustained release compared to the release profile of pure ametryn. When ametryn was associated with the PHB and PHBV microparticles, the amount of herbicide released in the same period of time was significantly reduced, declining to 75% and 87%, respectively. For both types of microparticle (PHB and PHBV) the release of ametryn was by diffusion processes due to anomalous transport (governed by diffusion and relaxation of the polymer chains), which did not follow Fick's laws of diffusion. The results presented in this paper are promising, in view of the successful encapsulation of ametryn in PHB or PHBV polymer microparticles, and indications that this system may help reduce the impacts caused by the herbicide, making it an environmentally safer alternative.

A self-referential HOWTO on release engineering

Energy Technology Data Exchange (ETDEWEB)

Galassi, Mark C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-31

Release engineering is a fundamental part of the software development cycle: it is the point at which quality control is exercised and bug fixes are integrated. The way in which software is released also gives the end user her first experience of a software package, while in scientific computing release engineering can guarantee reproducibility. For these reasons and others, the release process is a good indicator of the maturity and organization of a development team. Software teams often do not put in place a release process at the beginning. This is unfortunate because the team does not have early and continuous execution of test suites, and it does not exercise the software in the same conditions as the end users. I describe an approach to release engineering based on the software tools developed and used by the GNU project, together with several specific proposals related to packaging and distribution. I do this in a step-by-step manner, demonstrating how this very paper is written and built using proper release engineering methods. Because many aspects of release engineering are not exercised in the building of the paper, the accompanying software repository also contains examples of software libraries.

SOL-Gel microspheres and nanospheres for controlled release applications

International Nuclear Information System (INIS)

Barbe, C.; Beyer, R.; Kong, L.; Blackford, M.; Trautman, R.; Bartlett, J.

2002-01-01

one hour. The particles thus produced were washed with cyclohexane and carefully dried. Release Kinetics. The release of the encapsulated species from the particles was monitored by placing a fixed quantity of the sample in water or physiological saline, and monitoring the concentration of the released species using UV/Vis spectroscopy. The fraction released was normalised to the total mass initially encapsulated. The influence of the emulsion chemistry on the size of the microspheres obtained at pH 2 is illustrated in Figure 1 for microspheres containing encapsulated Orange II Using essentially identical sol-gel chemistries, particles with dimensions ranging from 50 nm to 50 μm can be readily obtained. The size of the particles is controlled by the size of the emulsion droplets, which act as micro-reactors for the sol-gel reactions. In turn, the size of the droplets is determined predominantly by the hydrophile/lipophile balance of the surfactant/ solvent couple and by processing parameters such as the water to surfactant ratio and the concentration of surfactant. The effect of sol-gel processing parameters on the morphology and associated release kinetics is illustrated in Figure 2. Although both samples have essentially identical particle sizes (not shown), their morphologies are significantly different. Processing under acidic conditions leads to the formation of nanosized linear silicate 'building block' which are woven tightly together in the final gel matrix, to produce a microporous material (pore diameters 2 nm). The different morphologies are clearly reflected in the release rate of the encapsulated species from the respective matrices; rapid release kinetics are evident for the mesoporous material (high pH), while significantly slower release rates are obtained for the microporous material (low pH). A combined sol-gel/emulsion processing method has been developed to produce inorganic matrices with tailored nanostructures containing encapsulated organic and

The Type 2 Diabetes Associated Minor Allele of rs2237895 KCNQ1 Associates with Reduced Insulin Release Following an Oral Glucose Load

DEFF Research Database (Denmark)

Brunak, Søren; Holmkvist, J; Banasik, K

2009-01-01

, and rs2237897) on estimates of glucose stimulated insulin release. METHODOLOGY/PRINCIPAL FINDINGS: Genotypes were examined for associations with serum insulin levels following an oral glucose tolerance test (OGTT) in a population-based sample of 6,039 middle-aged and treatment-naïve individuals. Insulin...... release indices estimated from the OGTT and the interplay between insulin sensitivity and insulin release were investigated using linear regression and Hotelling T2 analyses. Applying an additive genetic model the minor C-allele of rs2237895 was associated with reduced serum insulin levels 30 min (mean......,568 individuals who were glucose tolerant. Adjustment for the degree of insulin sensitivity had no effect on the measures of reduced insulin release. The rs2237895 genotype had a similar impact in the total sample of treatment-naïve individuals. No association with measures of insulin release were identified...

Techniques for Reaeration of Hydropower Releases.

Science.gov (United States)

1983-02-01

release improvement. However, selected reservoir aeration studies not conducted primarily for improving hydroturbine releases but which have application...for hydroturbine release reaeration were also reviewed. Because oxygen transfer mechanisms are vitally important to the development of more efficient...the key words turbine aeration, turbine vent, turbine I’ aspiration, hydroturbine aeration, tailrace aeration, draft tube vent, and vacuum breaker. A

An evaluation of nodalization/decay heat/ volatile fission product release models in ISAAC code

Energy Technology Data Exchange (ETDEWEB)

Song, Yong Mann; Park, Soo Yong; Kim, Dong Ha

2003-03-01

An ISAAC computer code, which was developed for a Level-2 PSA during 1995, has developed mainly with fundamental models for CANDU-specific severe accident progression and also the accident-analyzing experiences are limited to Level-2 PSA purposes. Hence the system nodalization model, decay model and volatile fission product release model, which are known to affect fission product behavior directly or indirectly, are evaluated to both enhance understanding for basic models and accumulate accident-analyzing experiences. As a research strategy, sensitivity studies of model parameters and sensitivity coefficients are performed. According to the results from core nodalization sensitivity study, an original 3x3 nodalization (per loop) method which groups horizontal fuel channels into 12 representative channels, is evaluated to be sufficient for an optimal scheme because detailed nodalization methods have no large effect on fuel thermal-hydraulic behavior, total accident progression and fission product behavior. As ANSI/ANS standard model for decay heat prediction after reactor trip has no needs for further model evaluation due to both wide application on accident analysis codes and good comparison results with the ORIGEN code, ISAAC calculational results of decay heat are used as they are. In addition, fission product revaporization in a containment which is caused by the embedded decay heat, is demonstrated. The results for the volatile fission product release model are analyzed. In case of early release, the IDCOR model with an in-vessel Te release option shows the most conservative results and for the late release case, NUREG-0772 model shows the most conservative results. Considering both early and late release, the IDCOR model with an in-vessel Te bound option shows mitigated conservative results.

Impact of IGF-I release kinetics on bone healing: a preliminary study in sheep.

Science.gov (United States)

Luginbuehl, Vera; Zoidis, Evangelos; Meinel, Lorenz; von Rechenberg, Brigitte; Gander, Bruno; Merkle, Hans P

2013-09-01

Spatiotemporal release of growth factors from a delivery device can profoundly affect the efficacy of bone growth induction. Here, we report on a delivery platform based on the encapsulation of insulin-like growth factor I (IGF-I) in different poly(D,L-lactide) (PLA) and poly(D,L-lactide-co-glycolide) (PLGA) microsphere (MS) formulations to control IGF-I release kinetics. In vitro IGF-I release profiles generally exhibited an initial burst (14-36% of total IGF-I content), which was followed by a more or less pronounced dormant phase with little release (2 to 34 days), and finally, a third phase of re-increased IGF-I release. The osteoinductive potential of these different IGF-I PL(G)A MS formulations was tested in studies using 8-mm metaphyseal drill hole bone defects in sheep. Histomorphometric analysis at 3 and 6 weeks after surgery showed that new bone formation was improved in the defects locally treated with IGF-I PL(G)A MS (n=5) as compared to defects filled with IGF-I-free PL(G)A MS (n=4). The extent of new bone formation was affected by the particular release kinetics, although a definitive relationship was not evident. Local administration of IGF-I resulted in down-regulation of inflammatory marker genes in all IGF-I treated defects. The over-expression of growth factor genes in response to IGF-I delivery was restricted to formulations that produced osteogenic responses. These experiments demonstrate the osteoinductive potential of sustained IGF-I delivery and show the importance of delivery kinetics for successful IGF-I-based therapies. Copyright © 2013 Elsevier B.V. All rights reserved.

In vitro histamine release from basophils of asthmatic and atopic individuals in D2O

International Nuclear Information System (INIS)

Tung, R.; Lichtenstein, L.M.

1982-01-01

It was found that spontaneous histamine release from human basophils in H 2 O-based buffers is negligible; in D 2 O-based buffers, however, release is observed with the cells of some donors. Analysis of this phenomenon revealed release from the basophils of 1 of 22 control individuals (5%), 15 of 47 patients with allergic rhinitis (32%), and 14 of 20 asthmatic patients (70%). The difference between both patient groups and controls and between atopics and asthmatics was highly significant. That D 2 O release was not cytotoxic is suggested by the finding that 37 0 was optimal, with inhibition at 4 0 C or 46 0 C as well as by EDTA, 2-deoxyglucose, and dibromoacetophenone, an inhibitor of phospholipase A 2 . The release mechanism was unusual in that dibutyryl cAMP and agonists that cause an increase in cAMP lead to no inhibition. No correlation was noted between the total serum IgE level (and thus the number of IgE receptors on the basophil surface) and the magnitude of D 2 O release. No increase in D 2 O release was observed in 17 ragweed-sensitive patients through a ragweed season. A unique property of D 2 O release was the loss of reactivity by preincubating cells at 37 0 C for 30 min before adding D 2 O. Non-D 2 O-reactive cells could be ''converted'' to D 2 O-reactive cells by incubation with antigen in the whole blood phase during leukocyte isolation; these cells showed the same loss of releaseability at 37 0 C and an inhibitor profile similar to D 2 O-responsive cells from ragweed allergic or asthmatic patients. We suggest that D 2 O-based buffers reveal, in atopic and asthmatic patients, in vivo basophil activation; whether this is due to IgE cross-links, to C split products, or to other stimuli is not yet clear

Press Oil Final Release Survey

Energy Technology Data Exchange (ETDEWEB)

Whicker, Jeffrey Jay [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ruedig, Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-05-11

There are forty-eight 55 gallon barrels filled with hydraulic oil that are candidates for release and recycle. This oil needs to be characterized prior to release. Principles of sampling as provided in MARSAME/MARSSIM approaches were used as guidance for sampling.

Morphology of Gas Release in Physical Simulants

Energy Technology Data Exchange (ETDEWEB)

Daniel, Richard C.; Burns, Carolyn A.; Crawford, Amanda D.; Hylden, Laura R.; Bryan, Samuel A.; MacFarlan, Paul J.; Gauglitz, Phillip A.

2014-07-03

This report documents testing activities conducted as part of the Deep Sludge Gas Release Event Project (DSGREP). The testing described in this report focused on evaluating the potential retention and release mechanisms of hydrogen bubbles in underground radioactive waste storage tanks at Hanford. The goal of the testing was to evaluate the rate, extent, and morphology of gas release events in simulant materials. Previous, undocumented scoping tests have evidenced dramatically different gas release behavior from simulants with similar physical properties. Specifically, previous gas release tests have evaluated the extent of release of 30 Pa kaolin and 30 Pa bentonite clay slurries. While both materials are clays and both have equivalent material shear strength using a shear vane, it was found that upon stirring, gas was released immediately and completely from bentonite clay slurry while little if any gas was released from the kaolin slurry. The motivation for the current work is to replicate these tests in a controlled quality test environment and to evaluate the release behavior for another simulant used in DSGREP testing. Three simulant materials were evaluated: 1) a 30 Pa kaolin clay slurry, 2) a 30 Pa bentonite clay slurry, and 3) Rayleigh-Taylor (RT) Simulant (a simulant designed to support DSGREP RT instability testing. Entrained gas was generated in these simulant materials using two methods: 1) application of vacuum over about a 1-minute period to nucleate dissolved gas within the simulant and 2) addition of hydrogen peroxide to generate gas by peroxide decomposition in the simulants over about a 16-hour period. Bubble release was effected by vibrating the test material using an external vibrating table. When testing with hydrogen peroxide, gas release was also accomplished by stirring of the simulant.

Analysis of accidental UF6 releases

International Nuclear Information System (INIS)

Fan Yumao; Tan Rui; Gao Qifa

2012-01-01

As interim substance in the nuclear fuel enrichment process, Uranium Hexafluoride (UF 6 ) is widely applied in nuclear processing, enrichment and fuel fabrication plants. Because of its vivid chemical characteristics and special radiological hazard and chemical toxicity, great attention must be paid to accident of UF 6 leakage. The chemical reactions involved in UF 6 release processes were introduced, therewith potential release styles, pathways and characteristics of diffusion were analyzed. The results indicated that the accidental release process of UF 6 is not a simple passive diffusion. So, specific atmospheric diffusion model related to UF 6 releases need be used in order to analyze and evaluate accurately the accidental consequences. (authors)

Effluent release limits, sources and control

International Nuclear Information System (INIS)

Swindell, G.E.

1977-01-01

Objectives of radiation protection in relation to releases. Environmental transfer models for radionuclides. Relationship between releases, environmental levels and doses to persons. Establishment of release limits: Limits based on critical population group concept critical pathway analysis and identification of critical group. Limits based on optimization of radiation protection individual dose limits, collective doses and dose commitments 1) differential cost benefit analysis 2) authorized and operational limits taking account of future exposures. Monitoring of releases to the environment: Objectives of effluent monitoring. Typical sources and composition of effluents; design and operation of monitoring programmes; recording and reporting of monitoring results; complementary environmental monitoring. (orig.) [de

Release plan for Big Pete

International Nuclear Information System (INIS)

Edwards, T.A.

1996-11-01

This release plan is to provide instructions for the Radiological Control Technician (RCT) to conduct surveys for the unconditional release of ''Big Pete,'' which was used in the removal of ''Spacers'' from the N-Reactor. Prior to performing surveys on the rear end portion of ''Big Pete,'' it shall be cleaned (i.e., free of oil, grease, caked soil, heavy dust). If no contamination is found, the vehicle may be released with the permission of the area RCT Supervisor. If contamination is found by any of the surveys, contact the cognizant Radiological Engineer for decontamination instructions

Short-term Outcomes following Concussion in the NFL: An 11-year Retrospective Study of Player Release Rate and Financial Loss

Science.gov (United States)

Ramkumar, Prem; Navarro, Sergio Michael

2017-01-01

Objectives: The primary goal of this study was to assess the short-term outcomes among National Football League (NFL) players following concussion in terms of: (1) DNP protocol activation, (2) release rate at one and three years, and (3) mean salary reduction. A secondary goal of the study was to stratify the post-concussive release rate by franchise and player position. Methods: NFL player transaction records and publicly available weekly injury reports from August 2005 to January 2016 for NFL players were analyzed. All players immediately sustaining recorded concussions were evaluated for a change to inactive or do-not-play (DNP) status. The one-year and three-year release rate following concussion was defined as any player transitioning to inactivation, retirement, free agency, or any failure to return for a successive season on the same team’s active roster after one or three years from the initial concussion. Student’s t-test was used to compare release rates between non-concussed and concussed players at one and three years. Mean salary reduction per year following concussion was calculated using publicly available player contracts. Additionally, franchise-level and position-based analyses of the release rate were performed. Results: Of the total 5,451 NFL players retrospectively analyzed over the 11-year period, 373 sustained publicly reported concussions resulting in DNP protocol activation. The release rate of the post-concussive versus non-concussive player was 26% vs. 20% at 1 year (pfranchise to release an athlete following concussion within one and three years. Table 1 reports a position-based analysis in terms of concussion rate, mean salary reduction, and NFL career longevity. Conclusion: Our retrospective study demonstrates that NFL concussions resulting in DNP protocol activation leads to a statistically greater release rate among concussed NFL players than non-concussed players. Released players suffered reduction in year-over-year accumulated

Fission-energy release for 16 fissioning nuclides. Final report

International Nuclear Information System (INIS)

Sher, R.

1981-03-01

Results are presented of a least-squares evaluation of the components of energy release per fission in 232 Th, 233 U, 235 U, 238 U, 239 Pu, and 241 Pu. For completeness, older (1978) results based on systematics are presented for these and ten other isotopes of interest. There have been recent indications that the delayed energy components may be somewhat higher than those used previously, but the LSQ results do not seem to change significantly when modest (approx. 1 MeV) increases in the total delayed energy are included in the inputs. Additional measurements of most of the energy components are still needed to resolve remaining discrepancies

Feeding Releases Endogenous Opioids in Humans.

Science.gov (United States)

Tuulari, Jetro J; Tuominen, Lauri; de Boer, Femke E; Hirvonen, Jussi; Helin, Semi; Nuutila, Pirjo; Nummenmaa, Lauri

2017-08-23

The endogenous opioid system supports a multitude of functions related to appetitive behavior in humans and animals, and it has been proposed to govern hedonic aspects of feeding thus contributing to the development of obesity. Here we used positron emission tomography to investigate whether feeding results in hedonia-dependent endogenous opioid release in humans. Ten healthy males were recruited for the study. They were scanned with the μ-opioid-specific ligand [ 11 C]carfentanil three times, as follows: after a palatable meal, a nonpalatable meal, and after an overnight fast. Subjective mood, satiety, and circulating hormone levels were measured. Feeding induced significant endogenous opioid release throughout the brain. This response was more pronounced following a nonpalatable meal versus a palatable meal, and independent of the subjective hedonic responses to feeding. We conclude that feeding consistently triggers cerebral opioid release even in the absence of subjective pleasure associated with feeding, suggesting that metabolic and homeostatic rather than exclusively hedonic responses play a role in the feeding-triggered cerebral opioid release. SIGNIFICANCE STATEMENT The endogenous opioid system supports both hedonic and homeostatic functions. It has been proposed that overeating and concomitant opioid release could downregulate opioid receptors and promote the development of obesity. However, it remains unresolved whether feeding leads to endogenous opioid release in humans. We used in vivo positron emission tomography to test whether feeding triggers cerebral opioid release and whether this response is associated with pleasurable sensations. We scanned volunteers using the μ-opioid receptor-specific radioligand [ 11 C]carfentanil three times, as follows: after an overnight fast, after consuming a palatable meal, and after consuming a nonpalatable meal. Feeding led to significant endogenous opioid release, and this occurred also in the absence of feeding

Ultrasound coupled with Fenton oxidation pre-treatment of sludge to release organic carbon, nitrogen and phosphorus

Energy Technology Data Exchange (ETDEWEB)

Gong, Changxiu [School of Environment, Tsinghua University, Beijing 100084 (China); Jiang, Jianguo, E-mail: jianguoj@mail.tsinghua.edu.cn [School of Environment, Tsinghua University, Beijing 100084 (China); Key Laboratory for Solid Waste Management and Environment Safety, Ministry of Education of China (China); Collaborative Innovation Center for Regional Environmental Quality, Tsinghua University, Beijing (China); Li, De' an [School of Environment, Tsinghua University, Beijing 100084 (China)

2015-11-01

We focused on the effects of ultrasound and Fenton reagent in ultrasonic coupling Fenton oxidation (U + F) pre-treatment processes on the disintegration of wastewater treatment plant sludge. The results demonstrated that U + F treatment could significantly increase soluble COD, TOC, total N, proteins, total P and PO{sub 4}{sup 3−} concentrations in sludge supernatant. This method was more effective than ultrasonic (U) or Fenton oxidation (F) treatment alone. U + F treatment increased the soluble COD by 2.1- and 1.4-fold compared with U and F alone, respectively. U + F treatment increased the total N and P by 1.7- and 2.2-fold, respectively, compared with F alone. After U + F treatment, sludge showed a considerably finer particle size and looser microstructure based on scanning electron microscopy, and the highest OH· signal intensity increased from 568.7 by F treatment to 1106.3 using electron spin resonance. This demonstrated that U + F treatment induces disintegration of sludge and release of organic carbon, nitrogen and phosphorus better. - Highlights: • Combined ultrasound–Fenton pre-treatment was proposed for sludge disintegration. • Ultrasound–Fenton significantly increased carbon, nitrogen and phosphorus release. • Higher level of OH· was detected after combined disintegration than Fenton.

Ultrasound coupled with Fenton oxidation pre-treatment of sludge to release organic carbon, nitrogen and phosphorus

International Nuclear Information System (INIS)

Gong, Changxiu; Jiang, Jianguo; Li, De'an

2015-01-01

We focused on the effects of ultrasound and Fenton reagent in ultrasonic coupling Fenton oxidation (U + F) pre-treatment processes on the disintegration of wastewater treatment plant sludge. The results demonstrated that U + F treatment could significantly increase soluble COD, TOC, total N, proteins, total P and PO 4 3− concentrations in sludge supernatant. This method was more effective than ultrasonic (U) or Fenton oxidation (F) treatment alone. U + F treatment increased the soluble COD by 2.1- and 1.4-fold compared with U and F alone, respectively. U + F treatment increased the total N and P by 1.7- and 2.2-fold, respectively, compared with F alone. After U + F treatment, sludge showed a considerably finer particle size and looser microstructure based on scanning electron microscopy, and the highest OH· signal intensity increased from 568.7 by F treatment to 1106.3 using electron spin resonance. This demonstrated that U + F treatment induces disintegration of sludge and release of organic carbon, nitrogen and phosphorus better. - Highlights: • Combined ultrasound–Fenton pre-treatment was proposed for sludge disintegration. • Ultrasound–Fenton significantly increased carbon, nitrogen and phosphorus release. • Higher level of OH· was detected after combined disintegration than Fenton

Nerve growth factor alters microtubule targeting agent-induced neurotransmitter release but not MTA-induced neurite retraction in sensory neurons.

Science.gov (United States)

Pittman, Sherry K; Gracias, Neilia G; Fehrenbacher, Jill C

2016-05-01

Peripheral neuropathy is a dose-limiting side effect of anticancer treatment with the microtubule-targeted agents (MTAs), paclitaxel and epothilone B (EpoB); however, the mechanisms by which the MTAs alter neuronal function and morphology are unknown. We previously demonstrated that paclitaxel alters neuronal sensitivity, in vitro, in the presence of nerve growth factor (NGF). Evidence in the literature suggests that NGF may modulate the neurotoxic effects of paclitaxel. Here, we examine whether NGF modulates changes in neuronal sensitivity and morphology induced by paclitaxel and EpoB. Neuronal sensitivity was assessed using the stimulated release of calcitonin gene-related peptide (CGRP), whereas morphology of established neurites was evaluated using a high content screening system. Dorsal root ganglion cultures, maintained in the absence or presence of NGF, were treated from day 7 to day 12 in culture with paclitaxel (300nM) or EpoB (30nM). Following treatment, the release of CGRP was stimulated using capsaicin or high extracellular potassium. In the presence of NGF, EpoB mimicked the effects of paclitaxel: capsaicin-stimulated release was attenuated, potassium-stimulated release was slightly enhanced and the total peptide content was unchanged. In the absence of NGF, both paclitaxel and EpoB decreased capsaicin- and potassium-stimulated release and the total peptide content, suggesting that NGF may reverse MTA-induced hyposensitivity. Paclitaxel and EpoB both decreased neurite length and branching, and this attenuation was unaffected by NGF in the growth media. These differential effects of NGF on neuronal sensitivity and morphology suggest that neurite retraction is not a causative factor to alter neuronal sensitivity. Copyright © 2016 Elsevier Inc. All rights reserved.

Should repository release criteria be based on collective dose, release limits, or individual doses?

International Nuclear Information System (INIS)

Channell, J.K.; Neill, R.H.

1999-01-01

The advantages and disadvantages of using each of 3 alternative methods (collective dose, release limits, and individual dose) as release criteria for determining long-term high level or transuranic waste repository performance of naturally occurring releases or man-made intrusions are evaluated. Each of the alternative approaches have positive aspects and each has uncertainties that require some arbitrary assumptions. A comparison of the numerical results from evaluating the three alternatives at WIPP leads to the conclusion that a collective dose is preferable because it is more site specific and allows consideration of the full effects of human intrusion. The main objection to release limits is they do not use site specific criteria to determine the radiological effect on local and regional populations. Individual dose criteria used and recommended in the United States have ignored doses to drillers and the public from wastes brought to the surface by human intrusion because these doses can be greater than acceptable limits. Also, there is disagreement about defining the location and lifestyle of the individual

Understanding Drug Release Data through Thermodynamic Analysis.

Science.gov (United States)

Freire, Marjorie Caroline Liberato Cavalcanti; Alexandrino, Francisco; Marcelino, Henrique Rodrigues; Picciani, Paulo Henrique de Souza; Silva, Kattya Gyselle de Holanda E; Genre, Julieta; Oliveira, Anselmo Gomes de; Egito, Eryvaldo Sócrates Tabosa do

2017-06-13

Understanding the factors that can modify the drug release profile of a drug from a Drug-Delivery-System (DDS) is a mandatory step to determine the effectiveness of new therapies. The aim of this study was to assess the Amphotericin-B (AmB) kinetic release profiles from polymeric systems with different compositions and geometries and to correlate these profiles with the thermodynamic parameters through mathematical modeling. Film casting and electrospinning techniques were used to compare behavior of films and fibers, respectively. Release profiles from the DDSs were performed, and the mathematical modeling of the data was carried out. Activation energy, enthalpy, entropy and Gibbs free energy of the drug release process were determined. AmB release profiles showed that the relationship to overcome the enthalpic barrier was PVA-fiber > PVA-film > PLA-fiber > PLA-film. Drug release kinetics from the fibers and the films were better fitted on the Peppas-Sahlin and Higuchi models, respectively. The thermodynamic parameters corroborate these findings, revealing that the AmB release from the evaluated systems was an endothermic and non-spontaneous process. Thermodynamic parameters can be used to explain the drug kinetic release profiles. Such an approach is of utmost importance for DDS containing insoluble compounds, such as AmB, which is associated with an erratic bioavailability.

Understanding Drug Release Data through Thermodynamic Analysis

Science.gov (United States)

Freire, Marjorie Caroline Liberato Cavalcanti; Alexandrino, Francisco; Marcelino, Henrique Rodrigues; Picciani, Paulo Henrique de Souza; Silva, Kattya Gyselle de Holanda e; Genre, Julieta; de Oliveira, Anselmo Gomes; do Egito, Eryvaldo Sócrates Tabosa

2017-01-01

Understanding the factors that can modify the drug release profile of a drug from a Drug-Delivery-System (DDS) is a mandatory step to determine the effectiveness of new therapies. The aim of this study was to assess the Amphotericin-B (AmB) kinetic release profiles from polymeric systems with different compositions and geometries and to correlate these profiles with the thermodynamic parameters through mathematical modeling. Film casting and electrospinning techniques were used to compare behavior of films and fibers, respectively. Release profiles from the DDSs were performed, and the mathematical modeling of the data was carried out. Activation energy, enthalpy, entropy and Gibbs free energy of the drug release process were determined. AmB release profiles showed that the relationship to overcome the enthalpic barrier was PVA-fiber > PVA-film > PLA-fiber > PLA-film. Drug release kinetics from the fibers and the films were better fitted on the Peppas–Sahlin and Higuchi models, respectively. The thermodynamic parameters corroborate these findings, revealing that the AmB release from the evaluated systems was an endothermic and non-spontaneous process. Thermodynamic parameters can be used to explain the drug kinetic release profiles. Such an approach is of utmost importance for DDS containing insoluble compounds, such as AmB, which is associated with an erratic bioavailability. PMID:28773009

Analysis of drug effects on neurotransmitter release

International Nuclear Information System (INIS)

Rowell, P.; Garner, A.

1986-01-01

The release of neurotransmitter is routinely studied in a superfusion system in which serial samples are collected and the effects of drugs or other treatments on the amount of material in the superfusate is determined. With frequent sampling interval, this procedure provides a mechanism for dynamically characterizing the release process itself. Using automated data collection in conjunction with polyexponential computer analysis, the equation which describes the release process in each experiment is determined. Analysis of the data during the nontreated phase of the experiment allows an internal control to be used for accurately assessing any changes in neurotransmitter release which may occur during a subsequent treatment phase. The use of internal controls greatly improves the signal to noise ratio and allows determinations of very low concentrations of drugs on small amounts of tissue to be made. In this presentation, the effects of 10 μM nicotine on 3 H-dopamine release in rat nucleus accumbens is described. The time course, potency and efficacy of the drug treatment is characterized using this system. Determinations of the exponential order of the release as well as the rate constants allow one to study the mechanism of the release process. A description of 3 H-dopamine release in normal as well as Ca ++ -free medium is presented

In vitro gentamicin release from commercially available calcium-phosphate bone substitutes influence of carrier type on duration of the release profile

Directory of Open Access Journals (Sweden)

Bronckers Antonius LJJ

2006-02-01

Full Text Available Abstract Background Polymethyl-methacrylate (PMMA beads releasing antibiotics are used extensively to treat osteomyelitis, but require surgical removal afterwards because they do not degrade. Methods As an alternative option, this report compares the in vitro gentamicin release profile from clinically used, biodegradable carrier-materials: six injectable cements and six granule-types. Cement cylinders and coated granules containing 3% gentamicin were submerged in dH2O and placed in a 48-sample parallel drug-release system. At regular intervals (30, 90, 180 min. and then every 24 h, for 21 days, the release fluid was exchanged and the gentamicin concentration was measured. The activity of released gentamicin was tested on Staphylococcus aureus. Results All combinations showed initial burst-release of active gentamicin, two cements had continuous-release (17 days. The relative release of all cements (36–85% and granules (30–62% was higher than previously reported for injectable PMMA-cements (up to 17% and comparable to other biodegradable carriers. From the cements residual gentamicin could be extracted, whereas the granules released all gentamicin that had adhered to the surface. Conclusion The high release achieved shows great promise for clinical application of these biodegradable drug-carriers. Using the appropriate combination, the required release profile (burst or sustained may be achieved.

Sustained Release Drug Delivery Applications of Polyurethanes

Directory of Open Access Journals (Sweden)

Michael B. Lowinger

2018-05-01

Full Text Available Since their introduction over 50 years ago, polyurethanes have been applied to nearly every industry. This review describes applications of polyurethanes to the development of modified release drug delivery. Although drug delivery research leveraging polyurethanes has been ongoing for decades, there has been renewed and substantial interest in the field in recent years. The chemistry of polyurethanes and the mechanisms of drug release from sustained release dosage forms are briefly reviewed. Studies to assess the impact of intrinsic drug properties on release from polyurethane-based formulations are considered. The impact of hydrophilic water swelling polyurethanes on drug diffusivity and release rate is discussed. The role of pore formers in modulating drug release rate is examined. Finally, the value of assessing mechanical properties of the dosage form and approaches taken in the literature are described.

Release of segregated nuclides from spent fuel

Energy Technology Data Exchange (ETDEWEB)

Johnson, L.H.; Tait, J.C. [Atomic Energy Canada Ltd., Pinawa, MB (Canada). Whiteshell Laboratories

1997-10-01

The potential release of fission and activation products from spent nuclear fuel into groundwater after container failure in the Swedish deep repository is discussed. Data from studies of fission gas release from representative Swedish BWR fuel are used to estimate the average fission gas release for the spent fuel population. Information from a variety of leaching studies on LWR and CANDU fuel are then reviewed as a basis for estimating the fraction of the inventory of key radionuclides that could be released preferentially (the Instant Release Fraction of IRF) upon failure of the fuel cladding. The uncertainties associated with these estimates are discussed. 33 refs, 6 figs, 3 tabs.

Iron isotope constraints on arsenic release from Mekong Delta sediments, Cambodia

Science.gov (United States)

Matsumoto, T.; Yamaguchi, K. E.; Hirata, T.; Yamagata, Y.; Yamaguchi, A.; Abe, G.

2017-12-01

Arsenic-contaminated groundwater is a world-wide environmental problem and threatens more than 100 million people living in delta areas of South, SE and East Asia. It is typically associated with reducing aquifers with organic-rich alluvial sediments, little thermal gradients, low sulfate concentrations, and slow flushing rates. Such conditions are typical for low-lying countries in Asian deltas; however, compared to Bangladesh, Cambodia has received far less attention. Upon reductive dissolution of Fe-(oxyhydr)oxides that adsorbed As, Fe and As are released into solution as dissolved Fe2+ and arsenate, respectively. Following the oxidation of dissolved Fe2+, newly-formed Fe-(oxyhydr)oxides adsorb As again. Thus, in anoxic waters, concentrations of As correlate with those of dissolved Fe2+. Fluctuating redox conditions in the aquifer are control As release, although inhibition of adsorption of arsenate and arsenite onto the Fe-(oxyhydr)oxides occurs when the concentrations of phosphate, bicarbonate, silicate, and/or organic matter become sufficiently high. Biogeochemical redox reactions of Fe result in significant isotope fractionation (e.g., Johnson et al., 2008). We hypothesized that magnitude of isotope fractionation of Fe in the aquifer sediments, reflecting repeated (incomplete) redox reactions of Fe, may be proportional to the amount of total As release. We aim to calibrate the As release from aquifer sediment by Fe isotope analysis. As a preliminary study, series of sediment samples were collected from the Mekong Delta, Cambodia, in September 2016. Based on measurements by XRF, ICP-AES and ICP-MS, concentrations of As varied significantly covering the range from 4.5 to 15.5 µg/g with a median value of 11 µg/g (higher than the average crustal value of 5 µg/g), and those of Fe is from 2.6 to 9.7 wt.% with a median value of 7.1 wt.%. Concentrations of As and Fe show positive correlation (R2 = 0.72), indicating an effective redox cycling of Fe and As as

Predicting patient exposure to nickel released from cardiovascular devices using multi-scale modeling.

Science.gov (United States)

Saylor, David M; Craven, Brent A; Chandrasekar, Vaishnavi; Simon, David D; Brown, Ronald P; Sussman, Eric M

2018-04-01

Many cardiovascular device alloys contain nickel, which if released in sufficient quantities, can lead to adverse health effects. However, in-vivo nickel release from implanted devices and subsequent biodistribution of nickel ions to local tissues and systemic circulation are not well understood. To address this uncertainty, we have developed a multi-scale (material, tissue, and system) biokinetic model. The model links nickel release from an implanted cardiovascular device to concentrations in peri-implant tissue, as well as in serum and urine, which can be readily monitored. The model was parameterized for a specific cardiovascular implant, nitinol septal occluders, using in-vitro nickel release test results, studies of ex-vivo uptake into heart tissue, and in-vivo and clinical measurements from the literature. Our results show that the model accurately predicts nickel concentrations in peri-implant tissue in an animal model and in serum and urine of septal occluder patients. The congruity of the model with these data suggests it may provide useful insight to establish nickel exposure limits and interpret biomonitoring data. Finally, we use the model to predict local and systemic nickel exposure due to passive release from nitinol devices produced using a wide range of manufacturing processes, as well as general relationships between release rate and exposure. These relationships suggest that peri-implant tissue and serum levels of nickel will remain below 5 μg/g and 10 μg/l, respectively, in patients who have received implanted nitinol cardiovascular devices provided the rate of nickel release per device surface area does not exceed 0.074 μg/(cm 2  d) and is less than 32 μg/d in total. The uncertainty in whether in-vitro tests used to evaluate metal ion release from medical products are representative of clinical environments is one of the largest roadblocks to establishing the associated patient risk. We have developed and validated a multi

Establishment of a paediatric age-related reference interval for the measurement of urinary total fractionated metanephrines.

LENUS (Irish Health Repository)

Griffin, Alison

2012-02-01

INTRODUCTION: Normetanephrine and metanephrine are intermediate metabolites of noradrenaline and adrenaline metabolism. To assess whether normetanephrine and metanephrine analysis may aid in the diagnosis of Neuroblastoma, a reference interval for these metabolites must first be established. AIM: The overall aim of this study was to establish a paediatric age-related reference interval for the measurement of total fractionated metanephrines. METHODS: A total of 267 urine samples were analysed following acid hydrolysis. This releases the metanephrines from their sulphate-bound metabolites. The samples were analysed using reverse phase high-performance liquid chromatography with electro-chemical detection on a Gilson automated sequential trace enrichment of dialysate sample system. RESULTS: Data were analysed using Minitab Release version 14. Outliers were removed using the Dixon\\/Reed one-third rule. Partitioning of the age groups was achieved using Harris and Boyd\\'s standard normal deviate test. Non-parametric analysis of the data was performed, followed by the establishment of the 2.5th and the 97.5th reference limits. CONCLUSIONS: The established reference intervals are described in Table 2.

Hypothalamic regulation of thyroid-stimulating hormone and prolactin release : the role of thyrotrophin-releasing hormone

NARCIS (Netherlands)

G.A.C. van Haasteren (Goedele)

1995-01-01

textabstractThyrotrophin-releasing-hormone (TRH), a tripeptide, is produced by hypothalamic neurons and transported along their axons to the median eminence (ME). From there it is released at nerve terminals into hypophyseal portal blood. It is then transported to the anterior pituitary gland where

Intracellular sphingosine releases calcium from lysosomes.

Science.gov (United States)

Höglinger, Doris; Haberkant, Per; Aguilera-Romero, Auxiliadora; Riezman, Howard; Porter, Forbes D; Platt, Frances M; Galione, Antony; Schultz, Carsten

2015-11-27

To elucidate new functions of sphingosine (Sph), we demonstrate that the spontaneous elevation of intracellular Sph levels via caged Sph leads to a significant and transient calcium release from acidic stores that is independent of sphingosine 1-phosphate, extracellular and ER calcium levels. This photo-induced Sph-driven calcium release requires the two-pore channel 1 (TPC1) residing on endosomes and lysosomes. Further, uncaging of Sph leads to the translocation of the autophagy-relevant transcription factor EB (TFEB) to the nucleus specifically after lysosomal calcium release. We confirm that Sph accumulates in late endosomes and lysosomes of cells derived from Niemann-Pick disease type C (NPC) patients and demonstrate a greatly reduced calcium release upon Sph uncaging. We conclude that sphingosine is a positive regulator of calcium release from acidic stores and that understanding the interplay between Sph homeostasis, calcium signaling and autophagy will be crucial in developing new therapies for lipid storage disorders such as NPC.

Food interactions with sustained-release theophylline preparations. A review.

Science.gov (United States)

Jonkman, J H

1989-03-01

Currently, theophylline is being used predominantly as sustained-release capsules or tablets. In the mid-seventies the first preparations for use with a dosage interval of 12 hours (twice-daily preparations) were introduced. Since 1983, theophylline preparations that can be given with an interval of 24 hours (once-daily preparations) have become available. The release of theophylline from some of these products can be influenced (either increased or decreased) by concomitant intake of food. With some preparations the composition of the meal (especially the fat content) has an influence on the degree of effect. The consequence may be an effect on the rate of absorption or on the amount absorbed, or both simultaneously. This could result in an unexpected shift of the plasma theophylline concentration. Such a shift is therapeutically undesirable, because theophylline has a fairly narrow therapeutic range. A review is given of those food interactions with the sustained-release theophylline preparations, both twice-daily and once-daily products, that are currently on the world market. Special attention is paid to the specific (bio)pharmaceutical characteristics of the different products, and to the influence of the composition and timing of the meals. For each preparation the effect of food on the following pharmacokinetic parameters is discussed: area under the plasma concentration-time curve, peak plasma drug concentration and time to reach this peak. Where possible, the results for both adults and children are discussed. There are indications that children are more susceptible to food-effects than adults. The regulatory aspects are mentioned briefly. Clinically important effects of food have been observed with the following twice-daily products: 'Theo-Dur Sprinkle', 'Theolair SR' (= 'Nuelin SR') and 'Theograd'. Pronounced effects could have an even greater impact with once-daily preparations, as the total daily dose will be given at a single time. A particularly