Grid generation method to calculate the flow field in a three-dimensional cascade of blades. Sanjigen yokuretsu nagare keisan no tame no koshi keisei

Energy Technology Data Exchange (ETDEWEB)

Inoue, K [National Aerospace Laboratory, Tokyo (Japan)

1992-05-01

For the purpose of developing a fan for an engine with ultra-high by-pass ratio, the design code of three-dimensional cascade of blades based on the Navier-Stokes equation has already been developed. This paper describes a method created by calculation grids which are part of this design code. This method is to generate boundary fitted grids to calculate the flow field across a cascade of blades placed radially in the axially symmetric space between hub and casing. In this method, one-period domain of the cascade of blades is mapped on a box in computational space by a series of combined streching transformation and conformal mapping. The grid in physical space is then obtained by successive inverse conformal mapping on the grid points in computational space. The grid obtained in this method is H-type and has a periodicity which includes the inclination of grid lines at the periodic boundary. As an example of the grid generated by this method, grids for primary and secondary models of the fan with ultra-high by-pass ratio are shown. 6 refs., 12 figs.

Grid generation method to calculate the flow field in a three-dimensional cascade of blades; Sanjigen yokuretsu nagare keisan no tame no koshi keisei

Energy Technology Data Exchange (ETDEWEB)

Inoue, K [National Aerospace Laboratory, Tokyo (Japan)

1992-05-01

For the purpose of developing a fan for an engine with ultra-high by-pass ratio, the design code of three-dimensional cascade of blades based on the Navier-Stokes equation has already been developed. This paper describes a method created by calculation grids which are part of this design code. This method is to generate boundary fitted grids to calculate the flow field across a cascade of blades placed radially in the axially symmetric space between hub and casing. In this method, one-period domain of the cascade of blades is mapped on a box in computational space by a series of combined streching transformation and conformal mapping. The grid in physical space is then obtained by successive inverse conformal mapping on the grid points in computational space. The grid obtained in this method is H-type and has a periodicity which includes the inclination of grid lines at the periodic boundary. As an example of the grid generated by this method, grids for primary and secondary models of the fan with ultra-high by-pass ratio are shown. 6 refs., 12 figs.

Possible sea sediments due to glaciofluvial activity in Elysium Planitia, Mars

Science.gov (United States)

Nussbaumer, J.

conditions to their geographic and stratigraphic positions, we intend to develop a geologic history of the central Elysium region. Ackowledgements for helpful contributions: D. Burr, J. Skinner, R. Williams References: [1] Tomei, K. (2004), Scriptum Publishers, 312 pp. [2] Burr et al. (2006) LPS XXXVII, #1367. [3] Evans, D. (2005), Hodder Arnold, 544pp. [4] Sharp M. J. (1984) Journal of Glaciology 82-93.

Fiscal 2000 survey report. Research on bone-forming dental material capable of reducing plaque adhesion; 2000 nendo shiko fuchaku boshigata hone keisei shika zairyo ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development efforts are exerted to produce advanced dental materials equipped with such functions as plaque reduction, bactericidal effect, and early formation of hydroxyapatite (HAP). In the study of fluorine ion implantation for plaque reduction, it is found that in a specimen implanted with fluorine ions the adhesion of carius streptococci is reduced to 1/3-1/10 for the achievement of remarkable improvement. In particular, carious streptococcus multiplication is suppressed when the metal shield layer is replaced with a titanium mesh. For the realization of a thin film formation method for osteoblast multiplication through reforming the material surface in the study of bone-forming dental materials, film formation conditions under which a P/Ca rate which is quite near that of ameloblast are achieved by use of a high frequency magnetron sputtering device. A titanium plate coated with a thus-formed film is annealed for a great increase in its wet contact angle, and then adhesion of bacteria is reduced and an osteoblast multiplication rate is increased by 20% or more, as compared with the case of no treatment in a petri dish. (NEDO)

Development of step for light duty truck by using injection molding of long-fiber reinforced thermoplastics; Chosen`i kyoka jushi no shashutsu keisei ni yoru truck yo step no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Togo, A; Yamamura, H; Yamaguchi, M [Mitsubishi Motor Corp., Tokyo (Japan); Yoshino, K [Kawasaki Steel Corp. Tokyo (Japan)

1997-10-01

The new step for light duty truck was developed by injection molding of glass long-fiber reinforced polypropylene. Feature of the step is good surface appearance and no post processings, compared with the conventional one press molded with a glass fiber reinforced polypropylene sheet (Stampable sheet). 3 refs., 14 figs., 6 tabs.

Mixture formation of direct gasoline injection engine. In cylinder gas sampling using fast response ionization detector; Tonai funsha gasoline engine no kongoki keisei. Kosoku FID ni yoru tonai gas sampling

Energy Technology Data Exchange (ETDEWEB)

Yamashita, H; Marubara, M; Ota, N; Kudo, H; Yamamoto, H [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

Local mixture concentration near the spark plug of a direct gasoline injection engine was observed by a fast flame ionization detector. To ensure combustion stability and good fuel economy in DISC operation, the swirl ratio and the piston configuration were optimized. Swirl is needed to retain well-vaporized and stable mixture near the spark plug especially in light load. And adequate volume in piston cavity is required for trapping curved fuel spray in it. With these specifications, the fuel economy improvement of 13 to 30 % was realized. 2 refs., 13 figs., 1 tab.

Study on initial stage of diesel spray formation. Effects of the condition inside the nozzle sac; Diesel funmu no shoki keisei katei ni kansuru kenkyu. Sac nai nenryo no eikyo

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, N.; Tsujimura, K. [Nissan Diesel Motor Co. Ltd., Saitama (Japan); Komori, M.

1996-06-25

To realize clean diesel exhaust, it is very important to clarify the atomization phenomena of the fuel spray. In this study, the initial stage of the atomization process of a diesel injection fuel spray was analyzed with a high-speed image converter camera under the conditions of atmospheric gas pressure and room temperature. As a result, it was found that the initial spray formation was greatly affected lay the condition inside the nozzle sac. In the case in which fuel existed in the sac, pin-like structure spray formation was observed at the initial injection stage. This phenomenon was not observed in the case in which no fuel was present in the sac, and a widely spread fuel spray formation was observed at the initial injection stage. The relatively low-speed fuel spray injected in the initial low-sac-pressure condition was pushed away by the subsequent fuel spray injected in the high-sac-pressure condition. 7 refs., 12 figs., 1 tab.

Na Bahia Setecentista, um pioneiro do abolicionismo? In eighteenth-century Bahia, a pioneer of abolitionism?

Directory of Open Access Journals (Sweden)

OFM Fr. Hugo Fragoso

2012-12-01

Full Text Available No ano de 1992, foi republicado por Paulo Suess Etíope Resgatado, de autoria do Pe. Manuel Ribeiro Rocha. Tratava-se de obra raríssima, pois, quanto consta, só havia em todo o Brasil um único exemplar, na Biblioteca Nacional do Rio de Janeiro. Já vinha eu fazendo pesquisas em torno do Pe. Ribeiro Rocha, a quem costumava qualificar de "pioneiro do abolicionismo" no Brasil. Com a reedição de Etíope Resgatado, tomei conhecimento da leitura de Paulo Suess, numa direção quase totalmente contrária. Para este, Ribeiro Rocha não passaria de um simples "reformista", que nada acrescentara de ideia libertária ao problema da escravidão negra. Aliás, essa tinha sido a tese de Ronaldo Vainfas e José Honório Rodrigues, que veem na obra de Ribeiro Rocha mais um exemplar do "pensamento escravista", que apenas condenava, como o faziam todos os homens de Igreja, os excessos e barbaridades da escravidão negra. Todo este nosso trabalho se orienta, portanto, na direção de uma leitura "abolicionista" do Etíope Resgatado, embora admita as evidências claras de "concessões" feitas por Ribeiro Rocha à situação escravocrata de seu tempo.In 1992, there was republished by Paulo Suess "Etíope resgatado", written by Father Manuel Ribeiro Rocha. It was very rare work, because, as stated, there was a single copy in the National Library of Rio de Janeiro in Brazil. I had, at this point, already started a research about the Father Ribeiro Rocha, whom used to be described as "a pioneer of abolitionism" in Brazil. With the reissue of "Etíope resgatado", I took notice about Paulo Suess lecture, in an almost completely opposite direction. According to Suess, Ribeiro Rocha was nothing more than a simple "reformer" who had added nothing to the problem of libertarian idea of black slavery. Incidentally, this was the thesis Vainfas Ronaldo and Jose Honorio Rodrigues argued, who saw the work of Ribeiro Rocha another copy of "slavery thought" which only condemned

Identidades e diferenças: um desafio às relações psicossociais na sala de aula / Identidades y diferencias: un desafío a las relaciones psicosociales en la sala de clase

Directory of Open Access Journals (Sweden)

Olga Solange Herval Souza

2007-01-01

Full Text Available Este artigo é um recorte da minha Tese de doutorado, defendida em Porto Alegre, na UFRGS, em 2002, que se constituiu em uma análise de práticas pedagógicas de um grupo de professores que atuavam no ensino fundamental e médio, e tinham em suas salas de aula, alunos com necessidades educacionais especiais. Realizei um estudo de campo, fundamentada nos pressupostos da pesquisa-ação, onde os sujeitos implicados tiveram algo “a dizer e a fazer”, desempenhando um papel ativo dentro da realidade em que os fatos foram observados. O escopo deste escrito, compõe-se de uma breveabordagem acerca da trama psicossocial que é construída no universo da sala de aula entre os diferentes sujeitos que ali convivem e interagem. Segundo o entendimento dos participantes do estudo, este tecido relacional é um fator que intervém na prática docente, e no processo de ensino/aprendizagem de forma a comprometer ou favorecer odesempenho escolar dos alunos, em particular daqueles que se destacam por suas diferenças e evocam uma atenção especial. Como aporte teórico, tomei por empréstimo algumas concepções de autores, entre eles: Paulo Freire, Philippe Perrenoud, Ramón Vallejo, Carlos Alberto Marques, Marisa Eizirik, Maria Cristina Mantovanini entre outros.Abstract Este artículo es un recorte de mi tesis de doctorado, defendida en Porto Alegre, en la UFRGS, en 2002, que se constituyó en una análisis de prácticas pedagógicas de un grupo de profesores que actuaban en la enseñanza fundamental y mediana, y tenían en sus salas de clase alumnos con necesidades educacionales especiales. Realicé un estudio de campo, fundamentada en los presupuestos de la pesquisa-acción, donde los sujetos implicados tuvieron algo “a decir y a hacer”, desempeñando un papel activo dentro de la realidad en que los hechos fueron observados. El propósito de este escrito se compone de una breve abordaje sobre la trama psicosocial que es construida en el universo de la

What can and should be legalized in ecological restoration? O que pode e deveria ser legalizado na restauração ecológica?

Directory of Open Access Journals (Sweden)

James Aronson

2010-06-01

Full Text Available After listing the five key elements of ecological restoration, ecology, economics, social values, cultural values, and politics, I celebrate the fact that in Brazil there is legislation on how to perform ecological restoration of degraded tropical forests, as well as an ongoing dialogue among legislators and scientists about this legislation, and also a lively debate among scientists as the best way forward, referring to articles by Brancalion et al. (2010 and Durigan et al. (2010 in this issue of Revista Árvore. Legislators elsewhere, especially megadiversity countries, should take note. I do not take sides in the debate; I think both groups of authors make very good points. Instead I call on the scientists and legislators concerned with restoration to ponder five strategic tools: A. Start with clear concepts. B. Decide where you want to go and why. C. Negotiate who should benefit & how, and who should pay, how, & why. D. Work out how an honest cost-benefit analysis of restoration would look, regardless of the biome in which you are working. Finally, figure out how to make the restoration immediately attractive for private landowners. Otherwise, they will not cooperate as fully as they could or should, and restoration efforts will not achieve its full potential.Depois de listar os cinco elementos chave da restauração ecológica - ecologia, economia, valores sociais, valores culturais e política, eu celebro o fato de que no Brasil há uma legislação sobre como conduzir a restauração ecológica de florestas tropicais degradadas, bem como o diálogo em andamento entre legisladores e cientistas sobre essa legislação, e também o intenso debate entre cientistas sobre a melhor forma de avançar, referindo aos artigos de Brancalion et al. (2010 e Durigan et al. (2010 nessa edição da Revista Árvore. Legisladores de todas as regiões, especialmente de países de megadiversidade, devem tomar nota. Eu não tomei partido por um dos lados no

FY 1997 report on the study on the formation condition of hetero-structure of single-crystalline semiconductor thin films; 1997 nendo chosa hokokusho (tankessho no handotai usumaku hetero kozo no keisei joken ni kansuru kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Since ion implantation causes material degradation by formation of crystalline defects, and hydrogen embrittlement deteriorates material strength, reduction of such defects has been positively studied. Study was made on a new active application of hydrogen separation into ion implantation defects. After H ion implantation of a proper depth into single-crystalline Si and SiC and successive annealing, single-crystalline films of sub-micron to several micron thick were obtained by hydrogen-induced delamination at the implantation depth due to hydrogen embrittlement in crystalline defects. The implantation depth is dependent on implantation energy. H atom forms (111) face defect through connection with dangling bond of crystalline defects. This crystal face defect forms a delamination plane through (100) face cleavage. This hydrogen embrittlement delamination by ion implantation is applicable to production of light-weight high-efficiency single-crystalline Si solar cells, and large single-crystalline SiC wafers as new resource saving process. 33 refs., 19 figs., 2 tabs.

Low temperature formation of ferroelectric PbTiO3 films by laser ablation with 2nd laser irradiation; Reiki hikari laser heiyo laser ablation ho ni yoru kyoyudentai PbTiO3 usumaku no teion keisei

Energy Technology Data Exchange (ETDEWEB)

Tabata, H.; Kawai, T. [Osaka University, Osaka (Japan)

1997-08-20

The unique advantage of the pulsed laser deposition is its ability to produce highly oriented stoichiometric films at a low substrate temperature. Ferroelectric PbTiO3 thin films have been formed using 2nd laser assisted laser ablaion technique at low temperature, i.e., 350degC, on Sr7iO3 single-crystal substrates and Pt/MgO electrodes. The second laser irradiation at the substrate surface is quite effective for crystallization of the films at low substrate temperature below 400degC. The suitable energy density (fluence) of the irradiation laser is in the range of 30-100 mJ/cm{sup 2}. X-ray diffraction patterns of PbTiO3 thin films show c-axis orientation, with a rocking angle of 1.0 - 0.5deg. These films exhibit ferroelectric hysteresis loop. The dielectric constant and remanent polalyzation of the PbTiO3 films are in the range of 120-150 and 60-80 {mu}C/cm{sup 2}, respectively. 31 refs., 10 figs., 1 tab.

Survey and study report for fiscal 1998 on the development of industrial utilization of a biofilm forming mechanism and inhibitors; 1998 nendo bio film keisei kiko oyobi sogai busshitsu no sangyoteki riyo kaihatsu chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The present study is intended to search for living organism deposition inhibiting active materials from the natural environment. Investigation on process of pollution in ocean reveals that adsorption of organic matters called conditioning occurs quickly on the surface, and the surface is covered by biofilms because of presence of bacteria and diatom in the surroundings. After the biofilms are formed, pollution occurs from living organisms, such as acorn barnacles. If the formation of the biofilms being the initial stage of living organism pollution in ocean can be controlled, deposition of large living organisms that follows the biofilm formation was anticipated to be controlled. Searches were made using this possibility as a parameter. The evaluation used a method to measure the antifungal properties specific to the bacteria. As a result of having made searches using this evaluation system, pyridylnitroalkanes were obtained. As compounds like phenethyl amines deeply involving in the deposition phenomenon were obtained, compounds having stronger activity were acquired by synthesizing the derivatives thereof. (NEDO)

CFD prediction of heat island formation on growing Asian cities. Effect of urbanization in Shanghai; Kyodaikasuru Asia no toshi ni okeru heat island keisei ni kansuru CFD yosoku. Shanghai no toshika ga oyobosu eikyo ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Ojima, T.; Murakami, S. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Mitsumoto, K. [Waseda University, Tokyo (Japan). School of Science and Engineering

1997-10-01

Study is conducted of the effect of change in land use and increase in artificial exhaust heat on heat island formation in Shanghai. Concerning the land use distribution in Shanghai, a point sampling survey was conducted in the 1930s using topographic charts, when the area was broken down into building-occupied region, paddy field, bare ground, and waters. In the 1990s, thanks to data from satellites, high-density and low-density urban regions have added. Calculation for Shanghai is performed, based on the rate of increase in Tokyo`s population and data predicted for Shanghai`s population, on the assumption that Shanghai`s population in the 2050s will grow 2.3 times larger than it is in the 1990s. The prediction thus produced indicates that the urban area in Shanghai in the 2050s will be as large as that of the present-day Tokyo that covers a 50km zone. Heat island formation prediction for Shanghai is worked out using computational fluid dynamics (CFD)-aided simulation. According to the prediction, while the maximum temperature in the 1930s was 29.6degC or 4degC higher than in the suburbs, it is 33.2degC or 7.6deg higher in the 1990s, and will be 34.4degC or 8.6degC higher in the 2050s. 16 refs., 11 figs., 1 tab.

Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system using animal waste; Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (chikusan haikibutsu riyo) jigyoka FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

To introduce the power generation system fueled by animal waste (excrements), one of the so-called industrial waste, its feasibility has been studied in Koyu and surrounding area located in Miyazaki Prefecture. This report includes the technical feasibility of available quantity of animal waste, chemical analysis of the waste, and basic design of the power generation system containing the furnace model and also its economical feasibility. The available quantity of animal waste in Koyu area is about 169,000 tons a year, which can generate 10.5 MW of electric power. That including the surrounding area is about 219,000 tons a year, which can generate 15.0 MW. The heating values of animal excrements in average and as received are 970 kcal/kg for pigs and 1,230 to 2,700 kcal/kg for broilers. In the case of combustion of mixed broiler and pig excrements, both of the stoker and fluidized-bed model furnaces become refractory furnace construction and provide with heat recovery boiler due to their high moisture content. In addition, the stoker furnace model requires an excrement dryer system as pre-treatment of fuel. For the fluidized-bed furnace of 15 MW grade power plant using the mixed fuel of 50% broiler excrements and 50% pig excrements, the power generation efficiency of 23% can be expected at generator end. The generating cost is around 10 yen/kWh. 27 refs., 61 tabs.

Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system using general RDF; Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (ippainado RDF riyo) jigyoka FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The refuse-derived fuel (RDF) has been holding public attention not only as the energy resource of stable high calorific value for local energy development, but also as the effective method for waste treatment. As one of the effective utilization methods for waste treatment, this investigation was conducted to industrialize and establish the RDF power generation system, in which power generation and ash treatment are integrated in Tochigi Prefecture which is located inland. The base supply type was adopted as a way of operation from the menu of the electricity wholesale project of Tokyo Electric Power Co. and its rate of operation is 80 percent a year. Then, the fluidized bed combustion method, a dry exhaust gas treatment method, and continuous electric melting furnaces were decided as the RDF power generation system. According to this system, it is possible to obtain 26 percent gross thermal efficiency by conventional generation facilities. It was estimated that the expenses reduction for 15 years will be 17.6 billion yen compared with the ordinary combustion system. Also, the following effects can be expected; the reduction of CO2 emission, improvement of energy efficiency, and the extension of life of landfills capacity. 36 figs., 51 tabs.

FY 1999 survey report on the research survey on the formation of a social consensus on the introduction of the global warming mitigation technology; 1999 nendo ondanka taisaku gijutsu no donyu ni kakawaru shakaiteki goi keisei ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to the development and introduction of the global warming mitigation technology, the paper studied an approach to the formation of a social consensus and how to apply concrete methods and proposed a realistic approach in the light of the present situation of public enterprises in Japan. As tools and rules which are particularly important in activities of forming the consensus, the paper cited up what the PR control should be, responses to mass communications, HP making and regulation/preparation of the related laws, and made a concrete study. As examples in which there occurred friction with the society due to the insufficient formation of consensus, the following construction plans were taken up to consider problems, etc. in disclosure of the information in the plans: Underground Research Laboratory, movable weir in the Yoshino River, and waste disposal facilities at Fuimae tideland. Also in Japan, some methods for the consensus formation have been carried out, and in the survey, as concepts for classifying the methods, two different approaches, Public Outreach and Public Relations, were introduced. As to the former, a consensus formation method in the construction of power plants in Japan was introduced, and as to the latter, a method in consensus conferences in the U.K. (NEDO)

Promotion of the formation of environmentally friendly energy community (FY 2000). Demonstration of the gas turbine repowering waste combined power generation technology; 2000 nendo kankyo chowagata energy community keisei sokushin seika hokokusho. Gas turbine repowering haikibutsu fukugo hatsuden gijutsu jissho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Demonstrative operation was conducted of the super waste power generation system in which the low temperature steam generated in waste incinerator is raised in temperature using the combustion exhaust gas emitted after the power generation using another gas turbine for conducting the steam turbine power generation with high efficiency. The FY 2000 results were summed up. In the demonstrative operation, operation and data acquisition/analysis were conducted following the previous fiscal year by 25MW class gas turbine repowering waste combined power generation facilities (Takahama power plant). Further, four years after the start of operation, the secular variation was studied by disassembly/inspection of equipment. As a result of the operation, the thermal efficiency was approximately 35%, much higher than the existing waste power generation. It was verified that the power system was maintained by the same maintenance as that of the ordinary power system. Moreover, the important point of this system is that no special corrosion resistant materials are used and that the high-efficiency waste power generation was demonstrated by combining the existing equipment. It can be said that the super waste power system has high qualities for forming energy community as a regionally dispersed stabilized power source. (NEDO)

FY 1999 results of the regional consortium R and D project/the regional consortium energy R and D. 1st year. Development of the energy-saving type production technology of high-purity/transparent silica glass; 1999 nendo kojundo tomei sekiei glass no sho energy gata seizo gijutsu no kaihatsu seika hokokusho. 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of achieving the remarkable energy conservation, high accuracy and low cost in the production of high-purity/transparent silica glass, the developmental research was conducted on slip casting method. In the development of technology to synthesize silica powder by the sol-gel method, monodisperse - polydisperse high-purity colloidal silica was obtained. In the development of technology to make silica power ultra-highly pure, a process was found out in which silica particles can be obtained by applying moderate amounts of ammonium bicarbonate and aqueous ammonia to the solution of silicic acid for heating. In the slip cast forming, a high-density forming body with a mean particle size of 1.5{mu}m was obtained. In the trial manufacture of reflector model, a translucent silica glass sintered body was obtained by transcribing the gypsum type dimensional shape in high purity. Besides, experimental researches were conducted on the examination of gypsum type/resin type and evaluation of physical properties, heat deterioration characteristics of the actual multi-layer film and trial manufacture of the heat resistant film, analysis/evaluation of trace impurities inside silica glass, conditions for the manufacture of dense silica glass sheets, etc. (NEDO)

Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system using CSD and other wastes; Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (CSD nado haikibutsu riyo) jigyoka FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This report presents the feasibility of enterprise on power generation by thermal recycle and selling power together with volume reduction, de-harming (de-toxification) and stabilization of the shredder dust. Contents of the study include the investigation of generation amount of car shredder dust (CSD) and its properties, trial design of high efficiency power generation facilities, selection of boiler tube materials, incineration test with a melting kiln test plant, disposal and effective use of melted slag and fly ash, and environmental impact assessment. The capacity of waste disposal in the trial design contains 1,140 ton/day of shredder dust, 60 ton/day of waste plastics, sludge and waste paper, and 130 ton/day of waste oil. Melting kiln with secondary combustion chamber was adopted as the incineration type. The high temperature and high pressure waste heat boiler with an extraction condensing turbine was adopted as the waste heat recovery and power generation type. Stable combustion was confirmed from the results using a test plant. According to the consideration of cost and unit cost results for wholesale power supply, if it is postulated that income for waste disposal is 12,000 yen/ton, power generation costs in excess power selling and wholesales are 6.4 yen/kWh and 9.1 yen/kWh, respectively. 67 figs., 48 tabs.

Research on fabrication technology for thin film solar cells for practical use. Research on low-cost fabrication technology for large-area modules (Over-layered TCO on tempered glass for solar cell); Usumaku taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Daimenseki module no tei cost seizo gijutsu (kyoka class fukugo tomei doden kiban seizo no gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on the fabrication technology of over-layered TCO on tempered glass in fiscal 1994. (1) On the fabrication technology of heat-resistant over-layered TCO, thermal deformation of TCO substrates was studied by both experiment and numerical computation. The thermal deformation increased with carrier concentration. As the observation result on change in lattice strain of heated TCO films by high-temperature X-ray diffraction, lattice strain was largely affected by thermal expansion. (2) On development of the low-temperature heat treatment method of TCO films, a technological prospect was obtained for fabrication of low-resistance TCO films by heat treatment without strength deterioration of tempered TCO substrates. (3) On development of cost reduction technology, the large-area CVD equipment was devised on the basis of the inline tempering method which tempers substrate glass by air cooling after formation of SnO2 film as fabrication method of tempered TCO. The TCO substrate tempered by air cooling could endure the drop test of 227g and 1.5m. 5 figs., 1 tab.

Fiscal 1998 research achievement report. Project for developing key technologies for electronic devices (Projection X-ray exposure process technology and active reflective device structure technology); 1998 nendo denshi device kiban gijutsu kaihatsu jigyo seika hokokusho. Shukusho X sen roko process gijutsu to active hansha kozogata keisei gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Studies were conducted for the development of technologies of the very advanced level relating to an ultrafine machining process and high-performance reflector type liquid crystal display structure formation. Studied in the research and development of projection X-ray exposure process technology were multi-layer film formation, absorbing body film formation, absorbing body machining, multi-layer film mask defect evaluation, and cleaning for defect reduction. As the result, multi-layer film formation by Helicon sputtering and formation and machining of film with Ta acting as absorbing body therein were carried out, and it was found by actual exposure experiments that there were excellent X-ray reflectivity and absorbing body contrast. Furthermore, a study was made of cleaning using dummy foreign matters, and 100% removal of dummy foreign matters was achieved across a range up to the 70nm level. Studied in the development of active reflective device structure technology were the addition of an electrical control function to the reflector, addition of an unreflected rays absorbing function, production of a bias stabilized device for the practical application of a memory function, and the development of materials for the fabrication of the said devices. (NEDO)

Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system (industrial refuse derived fuel and gas turbine combined type); Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (sangyo RDF GT fukugogata) jigyoka FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

High efficiency power generation, which is useful for promoting the environment-friendly type energy and coordinated community, is investigated by combining a steam turbine power generation system using the PS-RDF (paper sludge-refuse derived fuel) and a gas turbine (GT) combined cycle. Industrialization plan for processing PS in low cost has been made to ensure the profitability by participating the wholesale power supply under the law of electric power industry. This combined system is similar to the so-called super power generation using municipal garbage, but the lower temperature of steam from GT waste heat boilers (WHB) is super-heated by the flue gas from RDF boiler, which is called advanced power generation system (A.S.S.). The total power generation capacity is 149,000 kW, which consists of three 35,000 kW units of GT and one 44,000 kW unit of steam turbine. When comparing the combined system (A.S.S.) and usual one with the independent installation of the RDF steam power generation system and a GT combined cycle, the A.S.S. provides the repowering efficiency of 7,600 kW output with exactly the same quantity of fuel input as usual one. 71 figs., 31 tabs.

Achievement report for fiscal 1998. Research and development of ultimate atom/molecule manipulating technologies (Development of technology for formation of advanced function materials for use under power generation environment); 1998 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim is to establish atom/molecule observing and manipulating technologies commonly applicable as basic technologies to industrial fields of new materials, electronics, biotechnology, chemistry, etc. The technologies to be established involve atom level observation and manipulation by mechanically probing into organic molecules such as those of solid surface DNA, microstructure formation with atoms arbitrarily arranged by use of a microfine electron beam and surface chemical properties, simulation by the first principle calculation for the theoretical prediction atom/mole surface application in a process, and new materials to replace semiconductors. The subjects of research and development selected for this fiscal year are the study of silicon nanostructure formation and physical properties, study of nanostructure formation technology based on cluster manipulation, study of nanostructure formation processes using chemical reaction control and local structure analysis, study of new properties of correlation-intensive electron based new materials, study of spin measuring technology, and the study of theoretical analysis of atom/molecule dynamic processes. (NEDO)

Effect of mixture formation process of premixed lean diesel combustion. Study of the effect of mixture homogeneity on premixed lean diesel combustion in aid of numerical simulation; Yokongo diesel nensho ni okeru kongoki keisei katei no eikyo. Kongoki no kin`itsusei no eikyo to suchi simulation ni yoru kosatsu

Energy Technology Data Exchange (ETDEWEB)

Shimazaki, N; Miyamoto, T; Akagawa, H; Tsujimura, K

1997-10-01

NOx emission was extremely decreased by PREDIC (PREmixed lean DIesel Combustion) in which fuel was injected at very early stage of compression stroke and the combustion started at near the TDC by self ignition. We have considered that NOx reduction is caused the decrease of a region of stoichiometric mixture ratio by means of extremely early injection. Therefore the homogeneity is very important to decrease of NOx. In this study to investigate the effect of mixture homogeneity in the PREDIC, gaseous fuels (DME, CH4) were charged into the intake, by the combination of direct fuel injection, the mixture heterogeneity was positively changed. In addition the mixture formation process is shown in aid of numerical simulation, it is observed that the homogeneous has the advantage of low NOx emission in PREDIC region. 9 refs., 10 figs., 1 tab.

FY 1993 Report on the technical results. Research and development of extreme handling technologies at atomic/molecular levels (Development of technologies for forming highly functional stock materials for power generation environments); 1993 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This research and development project is aimed at development of the technologies for observing/handling solid surfaces and organic molecules at the atomic level by the mechanical probe; forming the fine structures of optional atomic sequences using fine electron beams and surface chemical characteristics; simulation by the first principle calculation to theoretically predict the atom/molecule surface reactions in a process; and producing new materials substitutes for semiconductors, in order to develop the atom/molecule observing and handling technologies as the common basic technologies for the various industrial areas, e.g., new materials, electronics, biotechnology and chemical. The research/survey activities are directed to (1) development of the technologies for observing the atoms and molecules on solid surfaces, (2) development of technologies for observing/handling intra-spatial atom groups, (3) development of the theoretical technologies for the atomic/molecular processes, and (4) auxiliary activities. The item (2) is intended to obtain the basic knowledge of the principles and devices for handling atom groups in a free space by spatial electromagnetic field handling or the like, and principles of state observation methods, including their possibilities. The item (4) holds the information-exchange meetings. (NEDO)

FY 2000 report on the survey of the project to promote and support the formation of the environmentally friendly energy community. Feasibility study on the waste utilization high efficiency power generation project; Kankyo chowagata energy community keisei sokushin jigyo chosa hokokusho. Haikibutsu riyo kokoritsu hatsuden jigyo ni kakawaru FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An investigational study was conducted on energy recovery (power generation) in disposal of industrial waste. The capacity of power generation facilities in incineration processing of industrial waste reached approximately 200,000kW (50 facilities) in the total nationwide. The incineration-processed waste is mainly chips of wood, waste tire and bagasse. Almost all the electric power is for non-utility use, and there are no examples of selling it outside. In the metropolitan area, there is only one example of the industrial waste incineration power generation in Tochigi prefecture. This is because there are extremely very few enterprises which are sources producing the waste as target. However, if the industrial waste market is targeted, there is a future. The industrial waste has a lot of disadvantages as power generation use fuel because of its diversification, but the use of it as fuel is technically easier than the use of the general waste as RDF. Accordingly, it can be used for power generation with no need of special technology or facilities. When picking up facilities with a potentiality of high efficiency power generation from the existing incinerators in operation of persons in charge of industrial waste processing, approximately 125,000 kW can be obtained only from remodeling of the existing facilities. (NEDO)

International joint research project of venture seeds excavating type in fiscal 1999 (revised) - venture seeds No.3. Report on achievements in developing bump forming technologies for high-density semiconductor connection; 1999 nendo (hosei) venture seeds hakkutsugata kokusai kyodo kenkyu jigyo - venture seeds No.3. Komitsudo handotai setsuzokuyo bump gata keisei gijutsu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Development has been advanced on a new flip chip technology with high efficiency and reliability to mount on lead frames and substrates the semiconductor devices that have been made higher in density and function and smaller in size. Specifically, discussions were given on a bump forming technology using micro balls with high accuracy and sphericity. With this technology, bumps are formed with high accuracy and efficiency by transferring and bonding the micro balls onto electrodes. Activities were taken in the following five areas: 1) discussions on the micro ball arranging technology, 2) optimization and evaluation on bed films, 3) manufacture and evaluation on micro balls, 4) overall evaluation and improvement discussion on quality and cost, and 5) analysis of thermal stress on soldered balls. In Item 1), micro balls are transferred onto pads after removing excess balls by sucking them into a suction head while having the micro balls float in a container by means of vibration. The suction arrangement plates were discussed and the suction system was optimized, whereas it was verified that balls with diameter of 100 {mu} m can be transferred and bonded onto pads of the chips without excess and insufficiency. (NEDO)

Report on a project to support promotion of forming an environmentally friendly energy community. Survey on an environmentally friendly community business by means of high-efficiency wastes power generation system in the Toyota-Kamo wide area; Kankyo chowagata energy community keisei sokushin hojo jigyo chosa hokokusho. Toyota Kamo koikiken kokoritsu haikibutsu hatsuden kankyo chowagata energy community jigyo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Taking the Toyota-Kamo wide area as the object, wastes power generation is positioned over the society system as worked on by administrations and operators integrally to incinerate mixedly those incineratable materials such as plastics among general and industrial combustible wastes for high-efficiency generation of power, which is supplied to electric utility operators as surplus power. Discussions were given on the business feasibility and the effectiveness as a society system. In this area, the mixed model B plan (dealing with general wastes plus industrial wastes) was evaluated as an effective plan as the society system. This is because the plan has effect to incinerate, melt and generate power from industrial wastes which have been used for land-fill, effect of improving the power generation efficiency, and effectiveness of mixed treatment with general wastes. The plan A in which general wastes are made into RDF, then incinerated mixedly with industrial wastes for power generation was evaluated to have high reliability potential of power supply and to be an effective plan as a society system, if effect can be expected to reduce transportation energy as a result of making the system large enough and turning wastes into RDF. (NEDO)

FY 2001 report on the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Potential survey of the commercialization of cogeneration using ligneous biomass in Kochi Prefecture; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Kochi ken mokushitsu kei baiomasu riyo netsuden heikyu jigyoka kanosei chosa itaku gyomu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

Survey/study were conducted of potentiality of the cogeneration business using ligneous biomass in Kami County and the periphery of Kochi Prefecture. In the survey, the following were studied: regional characteristics of the said area, levels of technology of direct combustion/thermochemical conversion, future technical trends, system candidate, grasp/analysis of the resource amount, characteristics of ligneous biomass resource in the said area, analysis of economical efficiency of the procurement of biomass resource, grasp of energy users, etc. As a result, a system was selected of a 1,000kW scale cogeneration of ligneous resource. At the present technology level and under scale conditions, it was found out that the fixed bed direct combustion system was the most profitable in securing the economical realization. As to the system mostly for power generation, however, it was found out that the heat low in unit price of energy production should widely be used because the installation cost of plant is comparatively high. Facilities such as Kochi Medical Center where heat is in great demand throughout the year can expect profit from selling heat, and therefore, those have high potentiality of the commercialization. (NEDO)

FY 1999 achievement report on the project on the R and D of industrial science technology. R and D of the atom/molecule limit operation technology (Development of high-functional material formation technology for electric power generation environment); 1999 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The paper described the FY 1999 results of the study of atomic technology. Using a combined system of the scanning tunnel microscope (STM) with the field ion microscope and the atom probe (AP), a few Ag atoms were identified. Si windows were formed by electron beam irradiated from a STM tip, and Ge nanocrystal array was formed at the windows by supplying GeH4 gas. Iron clusters were deposited on Si substrates. With those as nuclei and in self-formation for etching masks, Si pillar distribution nano-crystals were etching-processed. The oxidation process of clean Si surface using ultra-high vacuum electron spin resonance was observed, and the incomplete state of the Si oxidation process was observed. Perovskite oxide superlattices composed of the two kinds were fabricated using the laser ablation method. The layer type antiferromagnetic spin arrangement is artificially modulated in the superlattices along the stacking direction. To observe the magnetic nano-structure, the development was commenced of a spin-polarized STM. The paper theoretically analyzed the dynamic process of atoms and molecules. (NEDO)

Project to support promotion of forming an environmentally friendly energy community. Survey report on 'a survey on introduction of an RDF electric power generation system utilizing general wastes in the Noto area'; Kankyo chowagata energy community keisei sokushin hojo jigyo. 'Noto chiiki ni okeru ippan haikibutsu riyo RDF hatsuden no donyu ni kansuru chosa' chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

A business feasibility survey was performed on introduction of an RDF electric power generation system utilizing general wastes in the Noto area. Wastes quantity was estimated by accounting for large-sized wastes to be generated newly as a result of enforcement of the container package recycling law, and transfer of non-combustible wastes to incineration. The quantity was estimated to be 84,000 tons annually. Quantities of RDF and heat were calculated from this estimation to be 103 tons per day and 400 lkcal/kg respectively. According to the result of discussing the RDF transportation systems, time-based freight was found advantageous for short distance, and distance freight system for long distance in terms of cost. Discussions for RDF power systems were carried out on an RDF circulation fluid bed furnace plus ash melting furnace, a fluid bed gasification melting furnace, and shaft furnace type gasification melting furnace. In a comprehensive view, it is difficult to distinguish them in terms of merit and demerit. Molten slag was assumed to be re-utilized, but cost for the re-utilization should be considered. According to the result of discussing the business feasibility, it was found difficult to make it profitable by operating the RDF power generation business alone, and wastes incineration charge should be collected. (NEDO)

FY 2001 report on the results of the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Survey of the commercialization of high efficiency power generation using fuel of waste such as waste construction materials; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Kensetsu haizai tou haikibutsu nenryo ni yoru kokoritsu hatsuden no jigyosei chosa chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

The paper studied a system for power generation and heat utilization using wood chips such as waste construction materials, used paper inappropriate for recycling and plastic refuse from neighboring local governments as fuel and assessed a potentiality of the commercialization. As to the system, the following were conducted: selection of the optimum combustor in the waste power generation, survey of the state of corrosion of boiler tube in the steam conditions and waste properties, selection of the optimum quality of boiler materials, etc. In the assessment of a potentiality of the commercialization, the commercialization was studied as in-house power generation/heat utilization business with a power generation scale of 9,950kW and a steam supply scale of 31.5t/h. As a result of the study, the energy conservation effect was found to be expected as follows: reduction of 33,000kL/y crude oil equivalent and reduction of 16,000t-CO2/y emission. As a result of studying the economical efficiency of business, the unit price of wood chip purchase and the unit price of waste plastic treatment which are required to recover the difference of the initial investment within 5 years were greatly different from the level as an aim. For the realization as business, a subsidy of 15% and more cost reduction were requested. (NEDO)

Achievement report for fiscal 1997 on development of technologies for practical photovoltaic system under New Sunshine Program. Manufacture of thin-film solar cell and of low-cost/large-area module (Formation of low-temperature film); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usukau taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module seizo gijutsu kaihatsu (teion maku keisei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A polycrystalline Si thin film formation technology is developed, which uses the flux process in which a reaction occurs between the target crystal and a flux component which is eutectic. Using this process, a crystal grain relatively large in diameter is obtained at a relatively low temperature. This method is now attracting attention as one of the technologies for producing crystalline Si film for use in thin-film polycrystalline Si solar cells. Especially when Al is used for flux, since Al is automatically doped into the target crystalline Si film, it is expected that the resulting film will serve as the ground for a photoactive layer provided with the BSF (back surface field) function which is important for the improvement of solar cell efficiency. A polycrystalline Si thin film is formed on a 2cm times 2cm-large glass substrate at a temperature not higher than 600 degrees C. It is recognized that films selectively oriented towards the (111) or (100) plane are acquired when other processes are employed. It is expected that the said Al-doped film provides a ground on which a BSF function-provided photoactive layer will be formed. (NEDO)

FY 2001 report on the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Potential survey of the introduction of a processing/power generation system using ASR in the South region of Tochigi Prefecture; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Tochigi ken nanbu chiiki ni okeru ASR (Shuredda dust) wo nenryo to shita shori hatsuden system no donyu kanosei chosa chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the consistent processing of waste automobile in Tochigi Prefecture and the neighboring area, survey/study were made of the thermal recycle using shredder dust, ASR (automobile shredder residue), as fuel as well as the material recycle. As to the amount of material recycle of waste automobile, the amount of potential recycle of iron, copper, plastic, etc. was estimated, and it was found out that the potential recycle of parts such as engine was 40-45%, that of iron scrap 35-40%, and that of ASR 20-25%. The amount of fuel (ASR amount) to be thrown into the gasification power generation system was set up at 150t. As the gasification power generation system, the pyrolysis gasifier and shaft kiln gasification melting furnace were selected. In the study of economical efficiency of the gasification power generation system, the following were considered: ASR processing price, plant cost, subsidy, running cost, char receiving price, power selling price, etc., but even in the case of the pyrolysis gasifier with highest valuation, both payback years and IRR did not reach the target. (NEDO)

Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (R and D of the formation of advanced materials for power generation environment); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Ten nanoscale Ge islands were successfully formed in proper positions on an Si substrate surface by using mask technology of nanoscale atomic layers. Growth of less-defect ZnSe films on a GaAs(110) surface was possible under various conditions. The magnetic transfer mechanism of Mn oxide with huge reluctance was clarified. Through study on selective-area deposition of Si on plasma-oxidized ultrathin SiO2 mask layers patterned by direct electron-beam exposure and an idea of SiO2/SiNx bilayer mask, direct use of the ultrathin mask layer as insulating layer in device structure was achieved. The superior property as electron beam resist of methano- fullerene composed of fullerene C60 with side chains including oxygen was clarified. The initial oxidation process of an Si(100) surface was analyzed, and the observation result by SREM was theoretically explained. Development of a high-resolution spin polarization electron microscope was also mentioned. 48 refs., 145 figs., 20 tabs.

FY 2000 report on the survey of the project to promote and support the formation of the environmentally friendly energy community. Study of the industrialization of the gasification power generation business by the pressurized two-stage gasification process using organic waste such as waste plastic as raw materials; 2000 nendo kankyo chowagata energy community keisei sokushin hojo jigyo chosa hokokusho. Kaatsu nidan gas ka process ni yoru hai plastic nado yuki haikibutsu wo genryo to suru gas ka hatsuden jigyo no jigyoka kento

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Viability was studied of the power generation business using plastic waste as fuel and the methanol production business. In the project, the container packing waste plastic which was sorted/collected is supplied by tender, and the organic waste such as shredder dust is mixed. And the electric power is supplied to the gasification power generation facilities by the pressurized two-stage gasification process, neighboring plants, etc. As an alternative, the methanol production was also studied. As a result of the study, if the total amount of the waste plastic needed at the supply price assumed at present can be supplied, the business can be viable economically even without subsidy, but if the supply risk in supposing tender is considered, a subsidy of approximately 10% of the equipment/plant investment is needed. As to the methanol production as an alternative, it was indicated that the economical efficiency is almost the same, but the profitability gets fast worse due to the waste plastic supply cost since there is not much income and expenses are high despite of the smaller investment size than that in the case of the power generation. (NEDO)

FY 2001 report on the results of the survey of the environmentally friendly type energy community project. Utilization of combustible waste as solid fuel in Shimizu City, Shizuoka Prefecture, and the wide spread sphere of municipalities (Facilities such as RDF+LNG combined use high efficiency waste power generation); 2001 nendo Shizuoka ken shimizu shi oyobi koiki shichoson ken ni okeru kanensei haikibutsu kokeika nenryo riyo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo chosa (RDF+LNG heiyo kokoritsu haikibutsu hatsuden tou shisetsu) chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

Survey/study were conducted of viability of an idea of the high efficiency power generation that combinedly use RDF from the refuse generated in Shizuoka/Yamanashi/Nagano prefectures and LNG from the LNG base in Shimizu City, Shizuoka Prefecture. In the survey of raw materials for RDF, the present amount that can be supplied to RDF power generation was estimated at 280 t/d in RDF and 4,300 Kcal/kg or more in heating value. As to the RDF/LNG combination power generation, combinations of RDF200t/d + 25MW (capacity of gas turbine power generation) or RDF200t/d + 70MW seem to be appropriate. And, 30% or more of RDF power generation efficiency is made possible. In the study of economical efficiency, expenses born by local governments were calculated supposing that the difference between the unit price of power selling and that of power generation in power generation is born by RDF suppliers. As a result, the share becomes approximately 8,600-12,000 yen/refuse t in 15-year operation, and was found lower than that in the existing small-/medium-scale refuse incineration treatment. The combustion flue gas associated with the power generation business becomes approximately 300,000 Nm{sup 3}/h. The gas turbine fuel is natural gas, and RDF is good in combustibility. Therefore, the effect on the environment is expected to be small. (NEDO)

From the Editor

Directory of Open Access Journals (Sweden)

Ugur Demiray

2011-10-01

approaches for educational environment design. Some research projects in distance learning are introduced in the world. Two books are reviewed in this issue. The book titled as ―DESIGNING INSTRUCTION FOR THE TRADITIONAL, ADULT, AND DISTANCE LEARNER: A New Engine for Technology-Based Teaching by Lawrence A. Tomei (Robert Morris University, USA. Adult students demand a wider variety of instructional strategies that encompass real-world, interactive, cooperative, and discovery learning experiences. Designing Instruction for the Traditional, Adult, and Distance Learner: A New Engine for Technology-Based Teaching explores how technology impacts the process of devising instructional plans as well as learning itself in adult students. Containing research from leading international experts, this publication proposes realistic and accurate archetypes to assist educators in incorporating state-of-the-art technologies into online instruction. The second book review on ―DISTANCE NURSE EDUCATION (UZAKTAN HEMSIRELIK EGITIMI‖, was written by Gulsun KURUBACAK & Belgin BOZ, Anadolu University Open Education Faculty, Department of Distance Education, Eskisehir, TURKEY. This book focuses on what distance nurse education design means, and how diverse approaches can be implemented in the distance nurse education programs through the ALINE Model. Based on this understanding, the book reflects a radical approach in which human rights and equity are manifested in the everyday digital lives of nurse from every level of distance education society. These distinguished and careful analyses are the most important critics of distance nurse education design, and also provide unprejudiced point of views of the progress for distance nurse education designs against several opponents. Moreover, this publishing presents sufficient explanations, interpretations, comparisons, developments, illustrations, constructions, realizations, debating and questionings on distance nurse education. Therefore, the