WorldWideScience

Sample records for titled alternative engine

  1. ALTERNATIVE FUELS FOR DIESEL ENGINES

    Directory of Open Access Journals (Sweden)

    Jacek Caban

    2013-12-01

    Full Text Available This paper presents the development and genesis of the use of alternative fuels in internal combustion ignition engines. Based on the analysis of the literature, this article shows various alternative fuels used in Poland and all over the world. Furthermore, this article describes the research directions for alternative fuels use in road transport powered by diesel engines.

  2. Alternative general-aircraft engines

    Science.gov (United States)

    Tomazic, W. A.

    1976-01-01

    The most promising alternative engine (or engines) for application to general aircraft in the post-1985 time period was defined, and the level of technology was cited to the point where confident development of a new engine can begin early in the 1980's. Low emissions, multifuel capability, and fuel economy were emphasized. Six alternative propulsion concepts were considered to be viable candidates for future general-aircraft application: the advanced spark-ignition piston, rotary combustion, two- and four-stroke diesel, Stirling, and gas turbine engines.

  3. Alternative Teacher Preparation Programs. Title II News You Can Use

    Science.gov (United States)

    Office of Postsecondary Education, US Department of Education, 2015

    2015-01-01

    Title II of the "Higher Education Act of 1965" ("HEA"), as amended in 2008 by the "Higher Education Opportunity Act," requires states to report annually on key elements of their teacher preparation programs and requirements for initial teacher credentialing, kindergarten through 12th grade. "Title II News You Can…

  4. Alternative Fuels DISI Engine Research ? Autoignition Metrics.

    Energy Technology Data Exchange (ETDEWEB)

    Sjoberg, Carl Magnus Goran [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Vuilleumier, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2018-02-01

    Improved engine efficiency is required to comply with future fuel economy standards. Alternative fuels have the potential to enable more efficient engines while addressing concerns about energy security. This project contributes to the science base needed by industry to develop highly efficient direct injection spark igniton (DISI) engines that also beneficially exploit the different properties of alternative fuels. Here, the emphasis is on quantifying autoignition behavior for a range of spark-ignited engine conditions, including directly injected boosted conditions. The efficiency of stoichiometrically operated spark ignition engines is often limited by fuel-oxidizer end-gas autoignition, which can result in engine knock. A fuel’s knock resistance is assessed empirically by the Research Octane Number (RON) and Motor Octane Number (MON) tests. By clarifying how these two tests relate to the autoignition behavior of conventional and alternative fuel formulations, fuel design guidelines for enhanced engine efficiency can be developed.

  5. Alternative Approach to Power Engineering

    DEFF Research Database (Denmark)

    Pedersen, Knud Ole Helgesen; Havemann, Henrik

    2000-01-01

    as young and dynamic. Consequently, the new courses apply IT as a gateway to power engineering. The courses present the students with: (1) a meaningful, easy understandable power engineering problem; (2) a realistic set-up in the laboratory; and (3) a microprocessor system used as a tool to solve...

  6. TITLE

    Directory of Open Access Journals (Sweden)

    Abdolhamid Papzan

    2013-01-01

    Full Text Available This study investigated entrepreneurial intention among graduate students of USM Engineering Campus. Applying the Theory of Planned Behavior (TPB; Ajzen, we examined the empirical model of entrepreneurial intention determinants. Although research has been conducted in entrepreneurial intention, limited study has been done among Iranian graduate students who are studying abroad. This research aims to fill this gap using Entrepreneurial Intention Questionnaire (EIQ, version 3.1. Accordingly, a survey study was applied and Iranian graduate students of the USM Engineering Campus were studied using the census method. The authors propose an empirical model and tested its reliability and validity using structural equation modeling. Data was analyzed using Spss16 and Amos18 software. Results revealed that the level of knowledge about business sources of assistance for entrepreneurs in addition to components of the TPB, affected entrepreneurial intention. Empirical model ‘s goodness of fit indices indicated good model fit x2=1.047, df=2, probability 0.592; NFI= 0.981; CFI= 1.000; RMSEA=0.000. It seems that current empirical model could be a guide for future research on this important topic.

  7. Alternative fusion concepts: engineering and utility considerations

    International Nuclear Information System (INIS)

    Gough, W.C.; Amherd, N.A.

    1978-01-01

    Alternative systems are described to be an integral part of the total fusion effort, making use of many developments of the mainline efforts but also contributing on a broad scale to improved understanding of fusion plasmas, technology and engineering. We hypothesize that the rationale for supporting alternative concepts will shift from physics related justifications to the perceived benefits for commercial use. Three principal factors are used to describe the commercialization potential of energy systems: technological risk, perceived benefit, and capital requirements. R and D can reduce the risk of a technology option, but perceived benefit and capital availability are largely governed by non-R and D elements. Hence, power station decision criteria as determined by electric-utility executives are presented, and a balance among the three commercialization factors described. An outline of past and on-going alternative concept reactor study endeavors is given and a suggestion for rapidly developing the physics base of the concepts is described

  8. Engineering assessment of inactive uranium mill tailings, Shiprock site, Shiprock, New Mexico. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-01-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Shiprock, New Mexico. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 1.7 million tons of tailings at the Shiprock site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The 11 alternative actions presented range from completion of the present ongoing EPA site decontamination plan (Option I), to stabilizing in-place with varying depths of cover material (Options II-IV), to removal to an isolated long-term disposal site (Options V-XI). All options include remedial action costs for off-site locations where tailings have been placed. Costs estimates for the 11 options range from $540,000 to $12,500,000. Reprocessing the tailings for uranium is not economically feasible

  9. Engineering assessment of inactive uranium mill tailings, Gunnison Site, Gunnison, Colorado. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-11-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Gunnison, Colorado. The Phase II - Title I services include the preparation of topographic measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 0.5 million tons of tailings at the Gunnison site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The nine alternative actions presented range from millsite decontamination (Option I), to adding various depths of stabilization cover material (Options II and III), to removal of the tailings to long-term storage sites and decontamination of the present site (Options IV through IX). Cost estimates for the nine options range from $480,000 to $5,890,000. Reprocessing the tailings for uranium does not appear to be economically attractive at present

  10. Engineering assessment of inactive uranium mill tailings, Shiprock site, Shiprock, New Mexico. Phase II, Title I

    Energy Technology Data Exchange (ETDEWEB)

    1977-03-31

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Shiprock, New Mexico. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 1.7 million tons of tailings at the Shiprock site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The 11 alternative actions presented range from completion of the present ongoing EPA site decontamination plan (Option I), to stabilizing in-place with varying depths of cover material (Options II-IV), to removal to an isolated long-term disposal site (Options V-XI). All options include remedial action costs for off-site locations where tailings have been placed. Costs estimates for the 11 options range from $540,000 to $12,500,000. Reprocessing the tailings for uranium is not economically feasible.

  11. Engineering assessment of inactive uranium mill tailings, Durango site, Durango, Colorado. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-11-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Durango, Colorado. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 1.555 million tons of tailings at the Durango site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The eight alternative actions presented range from vegetative stabilization (Option I), to contouring and stabilizing in-place with varying depths of cover material (Options II and III), to removal to an isolated long-term disposal site (Options V to VIII). All options include remedial action costs for offsite locations where tailings have been placed. Costs estimated for the eight options range from $4,340,000 to $13,590,000. Reprocessing the tailings for uranium is sufficiently economically attractive to justify reprocessing in conjunction with each of the options

  12. Engineering assessment of inactive uranium mill tailings, Maybell site, Maybell, Colorado. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-10-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Maybell, Colorado. The Phase II--Title I services include the preparation of topographic maps, the performance of core drillings sufficient to determine areas and volumes of tailings and radiometric measurements to determine radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 2.6 million tons of tailings at the Maybell site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The three alternative actions presented range from fencing and maintenance (Option I), to placing the tailings in an open-pit mine and adding 2 ft of stabilization cover material (Option III). Cost estimates for the three options range from $250,000 to $4,520,000. Reprocessing the tailings for uranium does not appear to be economically attractive at present

  13. Utilization of alternative fuels in diesel engines

    Science.gov (United States)

    Lestz, S. A.

    1984-01-01

    Performance and emission data are collected for various candidate alternate fuels and compare these data to that for a certified petroleum based number two Diesel fuel oil. Results for methanol, ethanol, four vegetable oils, two shale derived oils, and two coal derived oils are reported. Alcohol fumigation does not appear to be a practical method for utilizing low combustion quality fuels in a Diesel engine. Alcohol fumigation enhances the bioactivity of the emitted exhaust particles. While it is possible to inject many synthetic fuels using the engine stock injection system, wholly acceptable performance is only obtained from a fuel whose specifications closely approach those of a finished petroleum based Diesel oil. This is illustrated by the contrast between the poor performance of the unupgraded coal derived fuel blends and the very good performance of the fully refined shale derived fuel.

  14. Engineering assessment of inactive uranium mill tailings, Naturita site, Naturita, Colorado. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-11-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Naturita, Colorado. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings sufficient to determine areas and volumes of tailings, the performance of radiometric measurements to determine the extent of radium contamination, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology, and the costing of alternative corrective actions. Radon gas release from the 704,000 tons of tailings at the Naturita site constitutes the most significant environmental impact although windblown tailings and external gamma radiation are also factors. Ranchers Exploration and Development Company has been licensed by the State of Colorado to reprocess the tailings at a location 3 mi from the present site where they will be stabilized for long-term storage. The remedial action options include remedial action for structures in Naturita and Nucla (Option I) at an estimated cost of $270,000 and remedial action for structures and open land adjacent to the tailings site (Option II) at an estimated cost of $950,000

  15. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 9

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-03-01

    140 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  16. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 7

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-03-01

    139 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  17. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 13

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-12-01

    136 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  18. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 14

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-12-01

    136 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  19. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 11

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-07-01

    158 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  20. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 6

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-03-01

    135 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  1. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 5

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-03-01

    133 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  2. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 12

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-12-01

    136 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  3. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 8

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-03-01

    141 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  4. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 4

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-03-01

    135 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  5. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 15

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-12-01

    137 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  6. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 10

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1979-07-01

    142 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are available on a loan basis from ZfK Rossendorf, Information Department, Dresden

  7. Title list of selected Soviet reports in the fields of nuclear research and nuclear engineering. 0

    International Nuclear Information System (INIS)

    Schumann, G.; Sube, R.

    1977-09-01

    161 titles of reports issued by Soviet institutes (KFTI, EFI, IAE, IFVE, ITEF, NIIAR, NIIEFA, FEI, RI, SFTI) in the fields of nuclear research and nuclear engineering have been arranged according to the INIS subject scope. The reports are availabl on a loan basis from ZfK Rossendorf, Information Department, Dresden

  8. Simulating the Use of Alternative Fuels in a Turbofan Engine

    Science.gov (United States)

    Litt, Jonathan S.; Chin, Jeffrey Chevoor; Liu, Yuan

    2013-01-01

    The interest in alternative fuels for aviation has created a need to evaluate their effect on engine performance. The use of dynamic turbofan engine simulations enables the comparative modeling of the performance of these fuels on a realistic test bed in terms of dynamic response and control compared to traditional fuels. The analysis of overall engine performance and response characteristics can lead to a determination of the practicality of using specific alternative fuels in commercial aircraft. This paper describes a procedure to model the use of alternative fuels in a large commercial turbofan engine, and quantifies their effects on engine and vehicle performance. In addition, the modeling effort notionally demonstrates that engine performance may be maintained by modifying engine control system software parameters to account for the alternative fuel.

  9. Single-piston alternative to Stirling engines

    International Nuclear Information System (INIS)

    Glushenkov, Maxim; Sprenkeler, Martin; Kronberg, Alexander; Kirillov, Valeriy

    2012-01-01

    Highlights: ► Thermodynamic analysis of an unconventional heat engine. ► The engine has a number of advantages compared to state-of-the-art Stirling engines. ► The engine can to be fuelled with “difficult” fuels and used for micro-CHP systems. ► The energy conversion efficiency can be as high as 40–50%. ► A prototype of the engine was demonstrated. -- Abstract: Thermodynamic analysis of an unconventional heat engine was performed. The engine studied has a number of advantages compared to state-of-the-art Stirling engines. The main advantage of the engine proposed is its simplicity. A power piston is integral with a displacer and a heat regenerator. It allows solving the problem of the high-temperature sealing of the piston and the displacer typical of all types of Stirling engines. In addition the design proposed provides ideal use of the displacer volume eliminating heat losses from outside gas circuit. Both strokes of the piston are working ones in contrary to any other types of piston engines. The engine can be considered as maintenance-free as it has no piston rings or any other rubbing components requiring lubrication. The only seal is contactless and wear free. It is located in the cold part of the cylinder. As a result the leakage rate in operation can be one-two orders of magnitude as small as that in Stirling engines. Balancing of the engine is much easy compared to Stirling engines with two reciprocating masses because of the only moving part inside the engine cylinder. The engine suits ideally to be fuelled with “difficult” fuels such as bio oil and can be used as a prime mover for micro-CHP systems. The thermodynamic model developed incorporates non-ideal features of the cycle, such as specific regenerator efficiency, dead volumes and other geometrical parameters of the engine. The model shows that the energy efficiency is highly sensitive to regenerator performance. For realistic geometric and operating parameters and the

  10. 75 FR 29605 - Clean Alternative Fuel Vehicle and Engine Conversions

    Science.gov (United States)

    2010-05-26

    ... Part II Environmental Protection Agency 40 CFR Parts 85 and 86 Clean Alternative Fuel Vehicle and...-0299; FRL-9149-9] RIN 2060-AP64 Clean Alternative Fuel Vehicle and Engine Conversions AGENCY... streamline the process by which manufacturers of clean alternative fuel conversion systems may demonstrate...

  11. Knowledge Expansion in Engineering Education: Engineering Technology as an Alternative

    Directory of Open Access Journals (Sweden)

    Kamsiah Mohd Ismail

    2015-07-01

    Full Text Available Abstract. The current and rising challenges in engineering education demand graduate engineers who are well-prepared to provide innovative solutions as technical specialists, system integrators and change agents. Realizing the importance of producing a highly competent manpower, the Malaysian Government has put considerable pressure to the universities to produce engineers who are competitive in the global market. Hence, this assignment of developing a highly competence engineering technologist workforce in support of the government policy highlights issues pertaining to the development and offering of practical-oriented programs as a knowledge expansion in engineering education at universities as envisioned by the Malaysian Government.  This paper evaluates the current scenario and examines the application-oriented programs of engineering technology education as practice in local institutions in Malaysia in comparisons to some universities abroad. It also investigates the challenges faced by university management in dealing with issues concerning national quality assurance and accreditation pertaining to the engineering technology education programs. Specifically, it analyzes the faculty planning of pedagogies in term of hands-on skills in teaching and learning. A key conclusion of this research is that Malaysian universities need to evaluate its engineering technology education strategies if they aim for quality assurance and accreditation to be established and aspire for successful attempts towards the creation of the requisite knowledge workers that Malaysia needs.Keywords: application-oriented, engineering education, engineering technology, hands-on skills, knowledge expansion 

  12. Stirling engine alternatives for the terrestrial solar application

    Science.gov (United States)

    Stearns, J.

    1985-01-01

    The first phase of the present study of Stirling engine alternatives for solar thermal-electric generation has been completed. Development risk levels are considered to be high for all engines evaluated. Free-piston type and Ringbom-type Stirling engine-alternators are not yet developed for the 25 to 50-kW electrical power range, although smaller machines have demonstrated the inherent robustness of the machines. Kinematic-type Stirling engines are presently achieving a 3500 hr lifetime or longer on critical components, and lifetime must still be further extended for the solar application. Operational and technical characteristics of all types of Stirling engines have been reviewed with engine developers. Technical work of merit in progress in each engine development organization should be recognized and supported in an appropriate manner.

  13. Engineering economic evaluations of trash segregation alternatives

    International Nuclear Information System (INIS)

    Collins, H.E.

    1987-01-01

    Health physicists are becoming increasingly involved in the selection of equipment to segregate a contaminated trash from clean trash in the effort to reduce low level waste disposal costs. Although well qualified to evaluate the technical merits of different equipment, health physicists also need to be aware of the elements of economic comparisons of different alternatives that meet all technical requirements

  14. Alternative evaluation of innovations’ effectiveness in mechanical engineering

    Science.gov (United States)

    Puryaev, A. S.

    2017-09-01

    The aim of present work is approbation of the developed technique for assessing innovations’ effectiveness. We demonstrate an alternative assessment of innovations’ effectiveness (innovation projects) in mechanical engineering on illustrative example. It is proposed as an alternative to the traditional method technique based on the value concept and the method of “Cash flow”.

  15. Solid state engine with alternating motion

    Science.gov (United States)

    Golestaneh, Ahmad A.

    1982-01-01

    Heat energy is converted to mechanical motion utilizing apparatus including a cylinder, a piston having openings therein reciprocable in the cylinder, inlet and outlet ports for warm water at one end of the cylinder, inlet and outlet ports for cool water at the other end of the cylinder, gates movable with the piston and slidably engaging the cylinder wall to alternately open and close the warm and cool water ports, a spring bearing against the warm water side of the piston and a double helix of a thermal shape memory material attached to the cool end of the cylinder and to the piston. The piston is caused to reciprocate by alternately admitting cool water and warm water to the cylinder.

  16. Phase II, Title I engineering assessment of inactive uranium mill tailings, Monument Valley site, Monument Valley, Arizona

    International Nuclear Information System (INIS)

    1977-01-01

    An engineering assessment was made of the problems resulting from the existence of radioactive uranium mill tailings at the Monument Valley millsite in Arizona. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals residing nearby, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the tailings on the site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The sparse population and relatively low radiation levels yield minimal immediate environmental impact; hence, the two alternative actions presented are directed towards restricting access to the site and returning the windblown tailings to the pile and stabilizing the pile. Both options include remedial action costs for offsite locations where tailings have been placed. Cost estimates for the two options are $585,000 and $1,165,000

  17. Engineering assessment of inactive uranium mill tailings, Rifle Site, Rifle, Colorado. Summary of the Phase II, Title I

    International Nuclear Information System (INIS)

    1977-10-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Rifle, Colorado. The Phase II - Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 3.1 million tons of tailings at the two Rifle sites, constitutes the most significant environmental impact. Windblown tailings, external gamma radiation and localized contamination of surface waters are other environmental effects. The 15 alternative remedial action options presented range from millsite decomtamination and off-site remedial action (Options I and IV), to adding various depths of stabilization cover material (Options II, V, VI, and VII), to removal of the tailings to long-term storage sites and decontamination of the present sites (Options III and VIII through XV). Cost estimates for the first 14 options range from $224,000 to $20,300,000. Option XV, estimated at $32,200,000, includes the cost for moving both Rifle tailings piles and the Grand Junction tailings pile to DeBeque for long-term storage and site decontamination after removal of the piles. Reprocessing of the tailings for uranium appears to be economically attractive at present

  18. Engineering assessment of inactive uranium mill tailings new and old Rifle site, Rifle, Colorado. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-10-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Rifle, Colorado. The Phase II--Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 3.1 million tons of tailings at the two Rifle sites, constitutes the most significant environmental impact. Windblown tailings, external gamma radiation and localized contamination of surface waters are other environmental effects. The 15 alternative remedial action options presented range from millsite decontamination and off-site remedial action (Options I and IV), to adding various depths of stabilization cover material (Options II, V, VI and VII), to removal of the tailings to long-term storage sites and decontamination of the present sites (Options III and VIII through XV). Cost estimates for the first 14 options range from $224,000 to $20,300,000. Option XV, estimated at $32,200,000, includes the cost for moving both Rifle tailings piles and the Grand Junction tailings pile to DeBeque for long-term storage and site decontamination after removal of the piles. Reprocessing of the tailings for uranium appears to be economically attractive at present

  19. Summary of the Phase II, Title I, engineering assessment of inactive uranium mill tailings, Gunnison Site, Gunnison, Colorado

    International Nuclear Information System (INIS)

    1977-11-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Gunnison, Colorado. The Phase II--Title I services include the preparation of topographic measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 0.5 million tons of tailings at the Gunnison site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The nine alternative actions presented range from millsite decontamination (Option I), to adding various depths of stabilization cover material (Options II and III), to removal of the tailings to long-term storage sites and decontamination of the present site (Options IV through IX). Cost estimates for the nine options range from $480,000 to $5,890,000. Reprocessing the tailings for uranium does not appear to be economically attractive at present

  20. Engineering assessment of inactive uranium mill tailings, Maybell Site, Maybell, Colorado. Summary of the Phase II, Title I

    International Nuclear Information System (INIS)

    1977-10-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Maybell, Colorado. The Phase II-Title I services include the preparation of topographic maps, the performance of core drillings sufficient to determine areas and volumes of tailings and radiometric measurements to determine radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 2.6 million tons of tailings at the Maybell site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The three alternative actions presented range from fencing and maintenance (Option I), to placing the tailings in an open-pit mine and adding 2 ft of stabilization cover material (Option III). Cost estimates for the three options range from $250,000 to $4,520,000. Reprocessing the tailings for uranium does not appear to be economically attractive at present

  1. Engineering assessment of inactive uranium mill tailings, Durango site, Durango, Colorado. A summary of the Phase II, Title I

    International Nuclear Information System (INIS)

    1977-11-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Durango, Colorado. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 1.555 million tons of tailings at the Durango site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The eight alternative actions presented range from vegetative stabilization (Option I), to contouring and stabilizing in-place with varying depths of cover material (Options II and III), to removal to an isolated long-term disposal site (Options V to VIII). All options include remedial action costs for offsite locations where tailings have been placed. Costs estimated for the eight options range from $4,340,000 to $13,590,000. Reprocessing the tailings for uranium is sufficiently economically attractive to justify reprocessing in conjunction with each of the options

  2. Engineering assessment of inactive uranium mill tailings, Grand Junction site, Grand Junction, Colorado. Phase II, Title I

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-10-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Grand Junction, Colorado. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 1.9 million tons of tailings at the Grand Junction site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The eight alternative actions presented range from millsite decontamination (Option I), to adding various depths of stabilization cover material (Options II and III), to removal of the tailings to long-term storage sites and decontamination of the present site (Options IV through VIII). Cost estimates for the eight options range from $470,000 to $18,130,000. Reprocessing the tailings for uranium recovery does not appear to be economically attractive at present.

  3. Engineering assessment of inactive uranium mill tailings new and old Rifle site, Rifle, Colorado. Phase II, Title I

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-10-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Rifle, Colorado. The Phase II--Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 3.1 million tons of tailings at the two Rifle sites, constitutes the most significant environmental impact. Windblown tailings, external gamma radiation and localized contamination of surface waters are other environmental effects. The 15 alternative remedial action options presented range from millsite decontamination and off-site remedial action (Options I and IV), to adding various depths of stabilization cover material (Options II, V, VI and VII), to removal of the tailings to long-term storage sites and decontamination of the present sites (Options III and VIII through XV). Cost estimates for the first 14 options range from $224,000 to $20,300,000. Option XV, estimated at $32,200,000, includes the cost for moving both Rifle tailings piles and the Grand Junction tailings pile to DeBeque for long-term storage and site decontamination after removal of the piles. Reprocessing of the tailings for uranium appears to be economically attractive at present.

  4. Engineering assessment of inactive uranium mill tailings, Grand Junction site, Grand Junction, Colorado. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-10-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Grand Junction, Colorado. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 1.9 million tons of tailings at the Grand Junction site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The eight alternative actions presented range from millsite decontamination (Option I), to adding various depths of stabilization cover material (Options II and III), to removal of the tailings to long-term storage sites and decontamination of the present site (Options IV through VIII). Cost estimates for the eight options range from $470,000 to $18,130,000. Reprocessing the tailings for uranium recovery does not appear to be economically attractive at present

  5. Engineering economics of alternative energy sources

    International Nuclear Information System (INIS)

    Denno, K.

    1990-01-01

    This textbook presents a comprehensive picture of the economic aspects, feasibility and adaptability of alternative energy sources and their interconnections. The author intends for this treatment of energy sources to be total and complete. It therefore includes such topics as low temperature and high temperature fuel cells, rechargeable storage batteries (including lead acid, nickel-cadmium, lithium, and sodium-sulfur), Redox flows cells energy system in compatibility with fuel cells and storage batteries, MHD energy systems using non-fossil renewable fuels, solar energy system using direct thermal units and photovoltaic generators, wind energy conversion systems, tidal ocean wave energy converters, geothermal energy, and ocean thermal energy conversion systems. The book is structured so that each major energy source is given one chapter. Each chapter begins with a discussion of the basic structural components of the energy source, as well as operational and fuel characteristics. This is followed by an economic analysis, which includes incremental energy cost curves and economic coordination equations for each possible system of operation. Where appropriate, economic scheduling of generation is applied to several modes of system consumption (e.g., localized dispersed systems, interconnected load centers, and central systems)

  6. The applicability of chemical alternatives assessment for engineered nanomaterials

    DEFF Research Database (Denmark)

    Hjorth, Rune; Hansen, Steffen Foss; Jacobs, Molly

    2017-01-01

    The use of alternatives assessment to substitute hazardous chemicals with inherently safer options is gaining momentum worldwide as a legislative and corporate strategy to minimize consumer, occupational, and environmental risks. Engineered nanomaterials represent an interesting case......, such as the use of mechanistic toxicity screens and control banding tools, alternatives assessment can be adapted to evaluate engineered nanomaterials both as potential substitutes for chemicals of concern and to ensure safer nanomaterials are incorporated in the design of new products. This article is protected...... for alternatives assessment approaches as they can be considered both emerging “chemicals” of concern, as well as potentially safer alternatives to hazardous chemicals. However, comparing the hazards of nanomaterials to traditional chemicals or to other nanomaterials is challenging and critical elements...

  7. Engineering assessment of inactive uranium mill tailings, Ray Point Site, Ray Point, Texas. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-12-01

    Results are reported from an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Ray Point, Texas. The Phase II--Title I services generally include the preparation of topographic maps, the performance of soil sampling and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. About 490,000 tons of ore were processed at this mill with all of the uranium sold on the commercial market. None was sold to the AEC; therefore, this report focuses on a physical description of the site and the identification of radiation pathways. No remedial action options were formulated for the site, inasmuch as none of the uranium was sold to the AEC and Exxon Corporation has agreed to perform all actions required by the State of Texas. Radon gas release from the tailings at the Ray Point site constitutes the most significant environmental impact. Windblown tailings, external gamma radiation and localized contamination of surface waters are other environmental effects. Exxon is also studying the feasibility of reprocessing the tailings

  8. Engineering assessment of inactive uranium mill tailings, Naturita site, Naturita, Colorado. A summary of the Phase II, Title I

    International Nuclear Information System (INIS)

    1977-11-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Naturita, Colorado. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings sufficient to determine areas and volumes of tailings, the performance of radiometric measurements to determine the extent of radium contamination, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology, and the costing of alternative corrective actions. Radon gas release from the 704,000 tons of tailings at the Naturita site constitutes the most significant environmental impact although windblown tailings and external gamma radiation are also factors. Ranchers Exploration and Development Company has been licensed by the State of Colorado to reprocess the tailings at a location 3 mi from the present site where they will be stabilized for long-term storage. The remedial action options include remedial action for structures in Naturita and Nucla (Option I) at an estimated cost of $270,000 and remedial action for structures and open land adjacent to the tailings site (Option II) at an estimated cost of $950,000

  9. Tamanu oil. An alternative fuel for variable compression ratio engine

    Energy Technology Data Exchange (ETDEWEB)

    Raj, Mohan T. [SASTRA Univ., Thanjavur, Tamilnadu (India). Dept. of Mechanical Engineering; Kandasamy, Murugumohan Kumar K. [Pavendar Bharathidasan College of Engineering and Technology, Trichy, Tamilnadu (India). Dept. of Mechanical Engineering

    2012-11-01

    Biodiesel can be produced from vegetable oils and also from waste fats. Biodiesel is a monoalkyl- ester of long chain fatty acids derived from renewable feedstock such as vegetable oils by transesterification process. The esterified cotton seed oil, pungam oil, rice bran oil, and tamanu oil are chosen as the alternative fuels. Among these oils, tamanu oil is considered for the first time as an alternative fuel. An experiment is conducted to obtain the operating characteristics of the variable compression ratio (VCR) engine run by chosen esterified oils, and the results are compared with esterified tamanu oil. From the comparison of results, it is inferred that the engine performance is improved with significant reduction in emissions for the chosen oils without any engine modification. The effective compression ratio can be fixed based on the experimental results obtained in the engine since the findings of the present research work infer that the biodiesel obtained from tamanu oil is a promising alternative fuel for direct-injection four-stroke VCR engine. (orig.)

  10. Alternative approaches to providing engineering expertise on shift

    International Nuclear Information System (INIS)

    Olson, J.; Schreiber, R.E.; Melber, B.D.

    1984-05-01

    This report represents the conclusions of a project studying the role of engineering expertise on shift in nuclear power plants. Using the present shift technical advisor (STA) position as the base case, several alternatives are analyzed. On-shift alternatives included the STA, the SS (shift supervisor), and the SE (shift engineer). The SE is degreed, experienced, trained, and licensed as a Senior Reactor Operator. Some non-shift alternatives were also studied. These included a cadre of on-call engineers and specialists within continual contact and easy reach of the plant; a technical system of phone and data lines linking the plant with a facility similar to an on-site technical support center; and finally, an SPDS (safety parameter display system) to agument technical upgrading of operator aids presently available. Potential problems considered in the analysis of implementation of these alternatives included job content constraints, problems of crew acceptance, and problems of labor supply and retention. Of the considered alternatives, the SE and SS options appear superior to the current STA approach. The SE approach appears the easiest to implement and the most effective under varied plant conditions. The SE may also serve as liaison to off-site support facilities

  11. Objective and automated protocols for the evaluation of biomedical search engines using No Title Evaluation protocols.

    Science.gov (United States)

    Campagne, Fabien

    2008-02-29

    The evaluation of information retrieval techniques has traditionally relied on human judges to determine which documents are relevant to a query and which are not. This protocol is used in the Text Retrieval Evaluation Conference (TREC), organized annually for the past 15 years, to support the unbiased evaluation of novel information retrieval approaches. The TREC Genomics Track has recently been introduced to measure the performance of information retrieval for biomedical applications. We describe two protocols for evaluating biomedical information retrieval techniques without human relevance judgments. We call these protocols No Title Evaluation (NT Evaluation). The first protocol measures performance for focused searches, where only one relevant document exists for each query. The second protocol measures performance for queries expected to have potentially many relevant documents per query (high-recall searches). Both protocols take advantage of the clear separation of titles and abstracts found in Medline. We compare the performance obtained with these evaluation protocols to results obtained by reusing the relevance judgments produced in the 2004 and 2005 TREC Genomics Track and observe significant correlations between performance rankings generated by our approach and TREC. Spearman's correlation coefficients in the range of 0.79-0.92 are observed comparing bpref measured with NT Evaluation or with TREC evaluations. For comparison, coefficients in the range 0.86-0.94 can be observed when evaluating the same set of methods with data from two independent TREC Genomics Track evaluations. We discuss the advantages of NT Evaluation over the TRels and the data fusion evaluation protocols introduced recently. Our results suggest that the NT Evaluation protocols described here could be used to optimize some search engine parameters before human evaluation. Further research is needed to determine if NT Evaluation or variants of these protocols can fully substitute

  12. Experimental Evaluation of the Free Piston Engine - Linear Alternator (FPLA)

    Energy Technology Data Exchange (ETDEWEB)

    Leick, Michael T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Moses, Ronald W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-03-01

    This report describes the experimental evaluation of a prototype free piston engine - linear alternator (FPLA) system developed at Sandia National Laboratories. The opposed piston design wa developed to investigate its potential for use in hybrid electric vehicles (HEVs). The system is mechanically simple with two - stroke uniflow scavenging for gas exchange and timed port fuel injection for fuel delivery, i.e. no complex valving. Electrical power is extracted from piston motion through linear alternators wh ich also provide a means for passive piston synchronization through electromagnetic coupling. In an HEV application, this electrical power would be used to charge the batteries. The engine - alternator system was designed, assembled and operated over a 2 - year period at Sandia National Laboratories in Livermore, CA. This report primarily contains a description of the as - built system, modifications to the system to enable better performance, and experimental results from start - up, motoring, and hydrogen combus tion tests.

  13. Engineering assessment of inactive uranium mill tailings, Slick Rock sites, Slick Rock, Colorado. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-10-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at the two millsites in Slick Rock, Colorado. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals residing nearby, the investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. The Union Carbide site has 350,000 tons of tailings and the North Continent site now owned by Union Carbide has 37,000 tons of tailings. Both tailings piles have been stabilized in accordance with regulations of the State of Colorado. Radon gas release from the tailings on the sites constitute the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The sparse population and relatively low radiation levels yield minimal immediate environmental impact. Hence the three alternative actions presented are directed towards restricting access to the sites (Option I), and returning the windblown tailings to the piles and stabilizing the piles with cover material (Option II), and consolidating the two piles on the UC site and stabilizing with 2 ft of cover (Option III). Fencing around the tailings piles is included in all options. Options II and III provide 2 ft of cover material on the tailings. Costs of the options range from $370,000 to $1,100,000. Reprocessing the tailings for uranium is not economically feasible

  14. Engineering assessment of inactive uranium mill tailings, Tuba City site, Tuba City, Arizona. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-01-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at the Tuba City millsite in Arizona. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals residing nearby, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the tailings on the site constitutes the most significant environmental impact to the inhabited area near the site. In the downwind direction, to the northeast of the site, airborne radioactivity is greater than Federal guidelines but there are no dwellings in that direction in the area of concern. Gamma radiation is significant over the tailings but is near background levels in the housing area. The sparse population and relatively low radiation levels yield minimal immediate environmental impact; hence, the four alternative actions presented are directed towards restricting access to the site (Option I), and returning the windblown tailings to the pile and stabilizing the pile with cover material (Options II, III, and IV). Fencing around the site or the tailings pile and the removal or decontamination of mill buildings is included in all options. Option II provides 2 ft of cover material on the tailings, Option III provides 4 ft of cover, and Option IV provides 13 ft of cover. Costs of the options range from $671,000 to $2,904,000. Reprocessing the tailings for uranium is only marginally feasible and would require a more detailed economic evaluation before any action was taken

  15. Expert System Approach For Generating And Evaluating Engine Design Alternatives

    Science.gov (United States)

    Shen, Stewart N. T.; Chew, Meng-Sang; Issa, Ghassan F.

    1989-03-01

    Artificial intelligence is becoming an increasingly important subject of study for computer scientists, engineering designers, as well as professionals in other fields. Even though AI technology is a relatively new discipline, many of its concepts have already found practical applications. Expert systems, in particular, have made significant contributions to technologies in such fields as business, medicine, engineering design, chemistry, and particle physics. This paper describes an expert system developed to aid the mechanical designer with the preliminary design of variable-stroke internal-combustion engines. The expert system accomplished its task by generating and evaluating a large number of design alternatives represented in the form of graphs. Through the application of structural and design rules directly to the graphs, optimal and near optimal preliminary design configurations of engines are deduced.

  16. Engineering assessment of inactive uranium mill tailings, Lakeview Site, Lakeview, Oregon. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-12-01

    Results are reported from an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at the Lakeview, Oregon site. Results are included from the analyses of soil, water, and other samples; radiometric measurements to determine areas with radium-contaminated materials; evaluation of resulting radiation exposures of individuals and nearby populations; investigation of site geology, hydrology, and meteorology; and evaluation and costing of alternative corrective actions. Radon gas release from the 130,000 tons of tailings at the Lakeview site constitutes the main environmental impact, which is minimal. The two alternative actions presented are maintenance of the site now that the ARCO reclamation program has been completed (Option I); and addition of stabilization cover to a minimum depth of 2 ft, improved fencing, and removal of a few isolated spots of contamination (Option II). The cost estimates for these options are $40,000 and $290,000, respectively

  17. Phase II, Title I, engineering assessment of inactive uranium mill tailings, Riverton Site, Riverton, Wyoming

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium mill tailings at the Spook Site, Converse County, Wyoming. Services include the performance of core drillings, soil, water and other sample analyses, radiometric measurements to determine areas with radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site geology, hydrology, and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 187,000 tons of tailings at the Spook Site constitutes the main environmental impact, which is negligible. The two alternative actions presented are better fencing of the site in its present state, and placing tailings and contaminated on-site materials and soil in the open-pit mine and covering the resulting pile with 2 ft of overburden materials. The cost estimates for the options are $81,000 and $142,000, respectively

  18. Phase II, Title I engineering assessment of radioactive sands and residues, Lowman Site, Lowman Idaho

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium sand residues at the Lowman, Idaho, site. Services normally include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 90,000 tons of sand residues at the Lowman site constitutes the most significant environmental impact, although external gamma radiation is also a factor. The two alternative actions presented are dike construction, fencing, and maintenance (Option I); and consolidation of the piles, addition of a 2-ft-thick stabilization cover, and on-site cleanup (Option II). Both options include remedial action at off-site structures. Cost estimates for the two options are $393,000 and $590,000

  19. Phase II, Title I engineering assessment of radioactive sands and residues, Lowman Site, Lowman Idaho

    Energy Technology Data Exchange (ETDEWEB)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium sand residues at the Lowman, Idaho, site. Services normally include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 90,000 tons of sand residues at the Lowman site constitutes the most significant environmental impact, although external gamma radiation is also a factor. The two alternative actions presented are dike construction, fencing, and maintenance (Option I); and consolidation of the piles, addition of a 2-ft-thick stabilization cover, and on-site cleanup (Option II). Both options include remedial action at off-site structures. Cost estimates for the two options are $393,000 and $590,000.

  20. Center for Alternative Fuels Research Program | College of Engineering &

    Science.gov (United States)

    Electrical Engineering Instructional Laboratories Student Resources Industrial & Manufacturing Engineering Industrial & Manufacturing Engineering Academic Programs Industrial & Manufacturing Engineering Major Industrial & Manufacturing Engineering Minor Industrial & Manufacturing Engineering

  1. Honeywell Engines, Systems and Services, Phoenix, Arizona, Petition to Object to Title V Operating Permit

    Science.gov (United States)

    This document may be of assistance in applying the Title V air operating permit regulations. This document is part of the Title V Petition Database available at www2.epa.gov/title-v-operating-permits/title-v-petition-database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

  2. Potentials and limitations of alternative fuels for diesel engine

    Directory of Open Access Journals (Sweden)

    Gligorijević Radinko

    2009-01-01

    Full Text Available The primary energy consumption in the world has increased continuously. The most important primary energy source is oil. The supply of automotive fuels today is based almost entirely on oil, and the demand for liquid transportation fuels worldwide will rise significantly in the next fifty years. Growing energy consumption and decreasing fossil resources are reasons for increasing prices of fossil fuel. Besides limited availability, contribution to greenhouse effect and pollutant emission represent another problem of fossil fuel. Both of these problems can be overcome by increased application of renewable biofuels. Therefore, great effort is made to supplement the primary energy sources by including renewable energies. There are alternative fuels 1st and 2nd generation. Some of them show high potential for reduction of engine out emission. But there are economical and technical barriers when such fuels are applied. This paper shows both advantage and disadvantage of alternative fuels, especially when used for diesel engines.

  3. Using Alcohols as an Alternative Fuel in Internal Combustion Engines

    Directory of Open Access Journals (Sweden)

    Salih ÖZER

    2014-04-01

    Full Text Available This study summarizes the studies on alcohol use in internal combustion engines nature. Nowadays, alcohol is used in internal combustion engines sometimes in order to reduce emissions and sometimes as an alternative fuel. Even vehicle manufacturers are producing and launching vehicles that are running directly with alcohol. Many types of pure alcohol that can be used on vehicles are available on the world. Using all of these types of alcohol led to the formation of engine emissions and power curves. The studies reveal that these changes are because of the physical and chemical characteristics of alcohols. Thıs study tries to explain what kind of conclusions the physical and chemical properties cause

  4. Effect of Engine Modifications on Performance and Emission Characteristics of Diesel Engines with Alternative Fuels

    OpenAIRE

    Venkateswarlu, K.; Murthy, B.S.R

    2010-01-01

    Performance and emission characteristics unmodified diesel engines operating on different alternative fuels with smaller blend proportions are comparable with pure diesel operation. But with increased blend proportions due to the associated problems of vegetable oils like high viscosity and low volatility pollution levels increase which however is accompanied by operating and durability problems with the long term usage of engine. This paper discusses the necessary modifications required to o...

  5. Engineering assessment of inactive uranium mill tailings, Spook site, Converse County, Wyoming. Phase II, Title I

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings was performed at the Spook Site, Converse County, Wyoming. Data are presented from soil, water and other sample analyses, radiometric measurements to determine areas with radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site geology, hydrology, and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 187,000 tons of tailings at the Spook Site constitutes the main environmental impact, which is negligible. The two alternative actions presented are better fencing of the site in its present state and placing tailings and contaminated on-site materials and soil in the open-pit mine and covering the resulting pile with 2 ft of overburden material. The cost estimates for the options are $81,000 and $142,000, respectively. Reprocessing the tailings for uranium at a nearby operating uranium mill is worthy of economic consideration at this time

  6. Societal lifecycle costs of cars with alternative fuels/engines

    International Nuclear Information System (INIS)

    Ogden, Joan M.; Williams, Robert H.; Larson, Eric D.

    2004-01-01

    Effectively addressing concerns about air pollution (especially health impacts of small-particle air pollution), climate change, and oil supply insecurity will probably require radical changes in automotive engine/fuel technologies in directions that offer both the potential for achieving near-zero emissions of air pollutants and greenhouse gases and a diversification of the transport fuel system away from its present exclusive dependence on petroleum. The basis for comparing alternative automotive engine/fuel options in evolving toward these goals in the present analysis is the 'societal lifecycle cost' of transportation, including the vehicle first cost (assuming large-scale mass production), fuel costs (assuming a fully developed fuel infrastructure), externality costs for oil supply security, and damage costs for emissions of air pollutants and greenhouse gases calculated over the full fuel cycle. Several engine/fuel options are considered--including current gasoline internal combustion engines and a variety of advanced lightweight vehicles: internal combustion engine vehicles fueled with gasoline or hydrogen; internal combustion engine/hybrid electric vehicles fueled with gasoline, compressed natural gas, Diesel, Fischer-Tropsch liquids or hydrogen; and fuel cell vehicles fueled with gasoline, methanol or hydrogen (from natural gas, coal or wind power). To account for large uncertainties inherent in the analysis (for example in environmental damage costs, in oil supply security costs and in projected mass-produced costs of future vehicles), lifecycle costs are estimated for a range of possible future conditions. Under base-case conditions, several advanced options have roughly comparable lifecycle costs that are lower than for today's conventional gasoline internal combustion engine cars, when environmental and oil supply insecurity externalities are counted--including advanced gasoline internal combustion engine cars, internal combustion engine

  7. The study, design and simulation of a free piston Stirling engine linear alternatorThe study, design and simulation of a free piston Stirling engine linear alternator

    Directory of Open Access Journals (Sweden)

    Teodora Susana Oros

    2014-12-01

    Full Text Available This paper presents a study, design and simulation of a Free Piston Stirling Engine Linear Alternator. There are presented the main steps of the magnetic and electric calculations for a permanent magnet linear alternator of fixed coil and moving magnets type. Finally, a detailed thermal, mechanical and electrical model for a Stirling engine linear alternator have been made in SIMULINK simulation program. The linear alternator simulation model uses a controllable DC voltage which simulates the linear alternator combined with a rectifier, a variable load and a DC-DC converter, which compensates for the variable nature of Stirling engine operation, and ensures a constant voltage output regardless of the load.

  8. Space Industry Commercialization: A Systems Engineering Evaluation of Alternatives

    Science.gov (United States)

    Dinally, Jihan

    The Constellation Program cancellation reversed the government and commercial space industry's roles and relationships by dedicating the majority of the federal funding and opportunities to the commercial space industry and left the government space industry in search of an approach to collaborate with the dominant organization, the commercial space industry service providers. The space industry government agencies, Air Force Space Command (AFSPC) and National Aeronautics and Space Administration (NASA) had realized that to gain resources in the new commercially oriented economic environment, they had to work together and possess the capabilities aligned with the National Space Policy's documented goals. Multi-organizational collaboration in space industry programs is challenging, as NASA, AFSPC, and commercial providers, follow different [1] enterprise architecture guidance such as the NASA systems engineering Handbook, MIL-STD-499 and "A Guide to the systems engineering Body of Knowledge" by the International Council on systems engineering [2] [3]. A solution to streamline their enterprise architecture documentation and meet National Space Policy goals is the Multi-User Architecture Maturity Model Methodology (MAM3), which offers a tailored systems engineering technique the government agencies and private companies can implement for the program's maturity level. In order to demonstrate the MAM3, a CubeSat motivated study was conducted partnering a commercial provider with a government agency. A survey of the commercial space industry service providers' capabilities was performed to select the private companies for the study. Using the survey results, the commercial space industry service providers were ranked using the Analytic Hierarchy Process (AHP) [4]. The AHP is a structured technique for making complex decisions for representing and quantifying its weights, relating those weights to overall goals, and evaluating alternative solutions [5] - [8]. The weights

  9. 40 CFR 86.347-79 - Alternative calculations for diesel engines.

    Science.gov (United States)

    2010-07-01

    ... Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test Procedures § 86.347-79 Alternative calculations for diesel engines. (a) This section applies to Diesel engines only. Gasoline-fueled engines must use the calculations in § 86.345. (b) For Diesel engines, the...

  10. Advanced materials for alternative fuel capable directly fired heat engines

    Energy Technology Data Exchange (ETDEWEB)

    Fairbanks, J.W.; Stringer, J. (eds.)

    1979-12-01

    The first conference on advanced materials for alternative fuel capable directly fired heat engines was held at the Maine Maritime Academy, Castine, Maine. It was sponsored by the US Department of Energy, (Assistant Secretary for Fossil Energy) and the Electric Power Research Institute, (Division of Fossil Fuel and Advanced Systems). Forty-four papers from the proceedings have been entered into EDB and ERA and one also into EAPA; three had been entered previously from other sources. The papers are concerned with US DOE research programs in this area, coal gasification, coal liquefaction, gas turbines, fluidized-bed combustion and the materials used in these processes or equipments. The materials papers involve alloys, ceramics, coatings, cladding, etc., and the fabrication and materials listing of such materials and studies involving corrosion, erosion, deposition, etc. (LTN)

  11. The disposal of Canada's nuclear fuel waste: engineered barriers alternatives

    International Nuclear Information System (INIS)

    Johnson, L.H.; Tait, J.C.; Shoesmith, D.W.; Crosthwaite, J.L.; Gray, M.N.

    1994-01-01

    The concept for disposal of Canada's nuclear fuel waste involves emplacing the waste in a vault excavated at a depth of 500 to 1000 m in plutonic rock of the Canadian Shield. The solid waste would be isolated from the biosphere by a multibarrier system consisting of engineered barriers, including long-lived containers and clay and cement-based sealing materials, and the natural barrier provided by the massive geological formation. The technical feasibility of this concept and its impact on the environment and human health are being documented in an Environmental Impact Statement (EIS), which will be submitted for review under the federal Environmental Assessment and Review Process. This report, one of nine EIS primary references, describes the various alternative designs and materials for engineered barriers that have been considered during the development of the Canadian disposal concept and summarizes engineered barrier concepts being evaluated in other countries. The basis for the selection of a reference engineered barrier system for the EIS is presented. This reference system involves placing used CANDU (Canada Deuterium Uranium) fuel bundles in titanium containers, which would then be emplaced in boreholes drilled in the floor of disposal rooms. Clay-based sealing materials would be used to fill both the space between the containers and the rock and the remaining excavations. In the section on waste forms, the properties of both used-fuel bundles and solidified high-level wastes, which would be produced by treating wastes resulting from the reprocessing of used fuel, are discussed. Methods of solidifying the wastes and the chemical durability of the solidified waste under disposal conditions are reviewed. Various alternative container designs are reviewed, ranging from preliminary conceptual designs to designs that have received extensive prototype testing. Results of structural performance, welding and inspection studies are also summarized. The corrosion of

  12. Alternate Material Pallet, 40" x 48", MIL-STD-1660, Engineering Evaluation Tests

    National Research Council Canada - National Science Library

    Dugan, Jeffery

    2003-01-01

    The U.S. Army Defense Ammunition Center (DAC), Validation Engineering Division (SJMAC-DEV) conducted Engineering Evaluation Tests to determine if the Alternate Material Pallet manufactured by Hunter Paine Enterprise, Inc...

  13. Engineering assessment of inactive uranium mill tailings, Mexican Hat site, Mexican Hat, Utah. A summary of the Phase II, Title I

    International Nuclear Information System (INIS)

    1977-01-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at the Mexican Hat millsite in Utah. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals residing nearby, the investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 2,200,000 tons of tailings on the site constitutes the most significant environmental impact. The six alternative actions presented are directed towards restricting access to the site (Option I), returning the windblown tailings to the piles and stabilizing the piles with cover material (Options II, III, and IV), and consolidating the two piles into one pile and stabilizing it with cover material (Options V and VI). Fencing around the site or the tailings and the decontamination of mill buildings is included in all options. Options II and V provide 2 ft of cover material on the tailings, Options III, IV, and VI provide 4 ft, 13 ft, and 10 ft of cover, respectively. Costs of the options range from $370,000 to $4,390,000. Reprocessing the tailings for uranium is not feasible at present

  14. Engineering assessment of inactive uranium mill tailings, Monument Valley site, Monument Valley, Arizona. A summary of the Phase II, Title I

    International Nuclear Information System (INIS)

    1977-01-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at the Monument Valley millsite in Arizona. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals residing nearby, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the tailings on the site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The sparse population and relatively low radiation levels yield minimal immediate environmental impact; hence, the two alternative actions presented are directed towards restricting access to the site (Options I and II), and returning the windblown tailings to the pile and stabilizing the pile with 2 ft of cover material (Option II). Both options include remedial action costs for offsite locations where tailings have been placed. Cost estimates for the two options are $585,000 and $1,165,000. Reprocessing the tailings for uranium is not economically feasible

  15. Engineering assessment of inactive uranium mill tailings, Grand Junction site, Grand Junction, Colorado. A summary of the Phase II, Title I

    International Nuclear Information System (INIS)

    1977-10-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Grand Junction, Colorado. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 1.9 million tons of tailings at the Grand Junction site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The eight alternative actions presented range from millsite decontamination (Option I), to adding various depths of stabilization cover material (Options II and III), to removal of the tailings to long-term storage sites and decontamination of the present site (Options IV through VIII). Cost estimates for the eight options range from $470,000 to $18,130,000. Reprocessing the tailings for uranium recovery does not appear to be economically attractive at present

  16. Comparing the Influence of Title and URL in Information Retrieval Relevance in Search Engines Results between Human Science and Agriculture Science

    Directory of Open Access Journals (Sweden)

    Parisa Allami

    2012-12-01

    Full Text Available When the World Wide Web provides suitable methods for producing and publishing information to scientists, the Web has become a mediator to publishing information. This environment has been formed billions of web pages that each of them has a special title, special content, special address and special purpose. Search engines provide a variety of facilities limit search results to raise the possibility of relevance in the retrieval results. One of these facilities is the limitation of the keywords and search terms to the title or URL. It can increase the possibility of results relevance significantly. Search engines claim what are limited to title and URL is most relevant. This research tried to compare the results relevant between results limited in title and URL in agricultural and Humanities areas from their users sights also it notice to Comparison of the presence of keywords in the title and URL between two areas and the relationship between search query numbers and matching keywords in title and their URLs. For this purpose, the number of 30 students in each area whom were in MA process and in doing their thesis was chosen. There was a significant relevant of the results that they limited their information needs to title and URL. There was significantly relevance in URL results in agricultural area, but there was not any significant difference between title and URL results in the humanities. For comparing the number of keywords in title and URL in two areas, 30 keywords in each area were chosen. There was not any significantly difference between the number of keywords in the title and URL of websites in two areas. To show relationship between number of search keyword and the matching of title and URL 45 keywords in each area were chosen. They were divided to three parts (one keyword, two keywords and three keywords. It was determined that if search keyword was less, the amount of matching between title and URL was more and if the matching

  17. Alternatives for Jet Engine Control. Volume 1: Modelling and Control Design with Jet Engine Data

    Science.gov (United States)

    Sain, M. K.

    1985-01-01

    This document compiles a comprehensive list of publications supported by, or related to, National Aeronautics and Space Administration Grant NSG-3048, entitled "Alternatives for Jet Engine Control". Dr. Kurt Seldner was the original Technical Officer for the grant, at Lewis Research Center. Dr. Bruce Lehtinen was the final Technical Officer. At the University of Notre Dame, Drs. Michael K. Sain and R. Jeffrey Leake were the original Project Directors, with Dr. Sain becoming the final Project Director. Publications cover work over a ten-year period. The Final Report is divided into two parts. Volume i, "Modelling and Control Design with Jet Engine Data", follows in this report. Volume 2, "Modelling and Control Design with Tensors", has been bound separately.

  18. Tissue engineering as a potential alternative or adjunct to surgical reconstruction in treating pelvic organ prolapse

    DEFF Research Database (Denmark)

    Boennelycke, M; Gräs, Søren; Lose, G

    2013-01-01

    Cell-based tissue engineering strategies could potentially provide attractive alternatives to surgical reconstruction of native tissue or the use of surgical implants in treating pelvic organ prolapse (POP).......Cell-based tissue engineering strategies could potentially provide attractive alternatives to surgical reconstruction of native tissue or the use of surgical implants in treating pelvic organ prolapse (POP)....

  19. An Alternative Route to Chemical Engineering for Minority and Other Students.

    Science.gov (United States)

    Cussler, E. L.

    The following three alternative ways in which minority group chemistry majors may be trained as chemical engineers are examined in this paper: (l) they are admitted as engineers and take the same courses as engineering students at the graduate level; (2) undergraduate courses are taken as part of the transition from chemistry to chemical…

  20. 76 FR 19829 - Clean Alternative Fuel Vehicle and Engine Conversions

    Science.gov (United States)

    2011-04-08

    ... INFORMATION CONTACT: Amy Bunker, Compliance and Innovative Strategies Division, U.S. Environmental Protection... Vehicle/Engine Selection D. Mixed-Fuel and Dual-Fuel Conversions E. Vehicle/Engine Labels, Packaging Labels, and Marketing F. Compliance 1. Emission Standards a. Light-Duty and Heavy-Duty Chassis Certified...

  1. Engineering assessment of inactive uranium mill tailings, Slick Rock sites, Slick Rock, Colorado. A summary of the Phase II, Title I

    International Nuclear Information System (INIS)

    1977-10-01

    Ford, Bacon and Davis Utah Inc. has performed an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at the two millsites in Slick Rock, Colorado. The Phase II, Title I services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals residing nearby, the investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. The Union Carbide site has 350,000 tons of tailings and the North Continent site now owned by Union Carbide has 37,000 tons of tailings. Both tailings piles have been stabilized in accordance with regulations of the State of Colorado. Radon gas release from the tailings on the sites constitute the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The sparse population and relatively low radiation levels yield minimal immediate environmental impact. Hence the three alternative actions presented are directed towards restricting access to the sites (Option I), and returning the windblown tailings to the piles and stabilizing the piles with cover material (Option II), and consolidating the two piles on the UC site and stabilizing with 2 ft of cover (Option III). Fencing around the tailings piles is included in all options. Options II and III provide 2 ft of cover material on the tailings. Costs of the options range from $370,000 to $1,100,000. Reprocessing the tailings for uranium is not economically feasible

  2. A free-piston Stirling engine/linear alternator controls and load interaction test facility

    Science.gov (United States)

    Rauch, Jeffrey S.; Kankam, M. David; Santiago, Walter; Madi, Frank J.

    1992-01-01

    A test facility at LeRC was assembled for evaluating free-piston Stirling engine/linear alternator control options, and interaction with various electrical loads. This facility is based on a 'SPIKE' engine/alternator. The engine/alternator, a multi-purpose load system, a digital computer based load and facility control, and a data acquisition system with both steady-periodic and transient capability are described. Preliminary steady-periodic results are included for several operating modes of a digital AC parasitic load control. Preliminary results on the transient response to switching a resistive AC user load are discussed.

  3. Evaluation of the effectiveness and feasibility of the Waste Isolation Pilot Plant engineered alternatives: Final report of the Engineered Alternatives Task Force

    International Nuclear Information System (INIS)

    1991-07-01

    The Engineered Alternatives Task Force (EATF) was established by the United States Department of Energy (DOE) WIPP Project Office (WPO) in September 1989 (Hunt, A., 1990), to evaluate the relative effectiveness and feasibility of implementation of selected design enhancements (referred to as ''engineered alternatives'') for the Waste Isolation Pilot Plant (WIPP). These enhancements consist of modifications of existing waste forms and/or the WIPP facility, and other design variations such as passive marker systems. The purpose of this report is to summarize the methodologies and results of evaluation of the effectiveness of selected engineered alternatives relative to the existing repository design, and to discuss the feasibility of implementing these alternatives with respect to availability of technology, cost, schedule, and regulatory concerns. The EATF has concluded that a number of engineered alternatives could be implemented to improve repository performance if WIPP performance assessment determines that either gas generation or human intrusion presents a problem in demonstrating compliance. Within waste treatment, Level 3 treatments are the most effective in addressing multiple performance parameters, but tend to be the most expensive, the most difficult and time-consuming to implement, and have the greatest regulatory requirements. Level 2 treatments are less expensive, faster, require less extensive permitting, and utilize off- the-shelf technology, but are less effective in addressing multiple performance parameters. Depending upon the performance parameter, Level 1 alternatives such as alternative backfills, alternative waste containers, or modified repository design should be thoroughly evaluated and eliminated before any decision is made to treat the waste. The present uncertainty in the degree to which the baseline WIPP design complies with 40 CFR Part 191 and 40 CFR Part 268 precludes specific recommendations at this time. 130 refs., 21 figs., 37 tabs

  4. List of titles of master's and doctor's dissertations in atomic energy engineering in 1990

    International Nuclear Information System (INIS)

    1990-01-01

    The report presents a list of dissertations in the field of atomic energy engineering filed in 1990. The list was developed by the Special Working Committee for Atomic Energy Education. The list contains a total of 228 master's dissertations, 20 of which were submitted to Hokkaido University, 21 to Tohoku University, 28 to the University of Tokyo, 22 to Tokyo Institute of Technology, 6 to Tokai University, 12 to Musashi Institute of Technology, 23 to Nagoya University, 27 to Kyoto University, 26 to Osaka University, 3 to Kobe University of Mercantile Marine, and 40 to Kyushu University. The list of doctor's dissertations filed by students at the end of their doctor's course contains a total of 15 studies, of which 1 was submitted to Tohoku University, 6 to the University of Tokyo, 4 to Tokyo Institute of Technology, 3 to Kyoto University, and 1 to Osaka University. The list of doctor's dissertations filed by researchers other than graduate school students contains 37 studies, of which 5 was submitted to Hokkaido University, 8 to the University of Tokyo, 3 to Tokyo Institute of Technology, 5 to Nagoya University, 5 to Kyoto University, 5 to Osaka University, and 6 to Kyushu University. (N.K.)

  5. Alternative Observers for SI Engine Air/Fuel Ratio Control

    DEFF Research Database (Denmark)

    Hendricks, Elbert; Poulsen, Jannik; Olsen, Mads Bruun

    1996-01-01

    In earlier work it has been shown that a nonlinear observer based on the use of the manifold pressure state equation and a nonlinear fuel film compensator can maintain accurate A/F ratio control during both steady state and transient operation. This observer may be called a manifold absolute pres...... engine control system designer with a variety of robust control systems which can easily be made redundant in order to satisfy newer engine emissions and diagnosis requirements and legislation...

  6. DESIGNING AND PROTOTYPING OF AN ALTERNATIVE ELLIPTIC INTERNAL COMBUSTION ENGINE

    OpenAIRE

    AKSOY, Nadir; İÇİNGÜR, Yakup

    2010-01-01

    ABSTRACTIn the conventional internal combustion engines, the elements of linear movement cause the friction power to increase the manufacturing economy to deteriorate and also cause vibration. The diameter of intake valves, which is smaller than the diameter of the cylinder, causes the volumetric efficiency to decrease. In the two stroke engines, in which the number of work per cycle is increased, power output per unit volume (kW/liter) is higher; however, specific fuel consumption decreases ...

  7. Phase II, Title I engineering assessment of inactive uranium mill tailings, Falls City Site, Falls City, Texas

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium mill tailings at Falls City, Texas. Services included taking soil samples, the performance of radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 2.5 million tons of tailings at the Falls City site constitutes the most significant environmental impact. Windblown tailings, external gamma radiation and localized contamination of surface waters are other environmental effects. The two alternative remedial action options presented include on-site and off-site cleanup, fencing, and hydrological monitoring, and in addition, stabilization of pile 2 with 2 ft of cover material. The costs are $1.84 million for Option I and $2.45 million for Option II

  8. Engineering assessment of inactive uranium mill tailings, Lakeview Site, Lakeview, Oregon. Summary of Phase II, Title I

    International Nuclear Information System (INIS)

    1977-12-01

    Results are reported from an engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at the Lakeview, Oregon site. Data ore included from the analyses of soil, water, and other samples; radiometric measurements to determine areas with radium-contaminated materials; evaluation of resulting radiation exposures of individuals and nearby populations; investigation of site geology, hydrology, and meteorology; and evaluation and costing of alternative corrective actions. Radon gas release from the 130,000 tons of tailings at the Lakeview site constitutes the main environmental impact, which is minimal. The two alternative actions presented are maintenance of the site now that the ARCO reclamation program has been completed (Option I); and addition of stabilization cover to a minimum depth of 2 ft, improved fencing, and removal of a few isolated spots of contamination (Option II). The cost estimates for these options are $40,000 and $290,000, respectively

  9. Summary of the Phase II, Title I engineering assessment of inactive uranium mill tailings, Falls City Site, Falls City, Texas

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium mill tailings at Falls City, Texas. Services included taking soil samples, the performance of radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 2.5 million tons of tailings at the Falls City site constitutes the most significant environmental impact. Windblown tailings, external gamma radiation and localized contamination of surface waters are other environmental effects. The two alternative remedial action options presented include on-site and off-site cleanup, fencing, and hydrological monitoring and, in addition, stabilization of pile 2 with 2 ft of cover material. The costs are $1.84 million and $2.45 million

  10. Summary of the Phase II, Title I engineering assessment of inactive uranium mill tailings, Lowman Site, Lowman, Idaho

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium sand residues at the Lowman, Idaho site. Services included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 90,000 tons of sand residues at the Lowman site constitutes the most significant environmental impact, although external gamma radiation is also a factor. The two alternative actions presented are dike construction, fencing, and maintenance; and consolidation of the piles, addition of a 2-ft-thick stabilization cover, and on-site cleanup. Both options include remedial action at off-site structures. Cost estimates for the two options are $393,000 and $590,000

  11. Summary of the Phase II, Title I engineering assessment of inactive uranium mill tailings, Tuba City site, Tuba City, Arizona

    International Nuclear Information System (INIS)

    1977-01-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium mill tailings at the Tuba City millsite in Arizona. Services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals residing nearby, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the tailings on the site constitutes the most significant environmental impact to the inhabited area near the site

  12. Demonstration of a free piston Stirling engine driven linear alternator, phase I report

    International Nuclear Information System (INIS)

    Goldwater, B.; Piller, S.; Rauch, J.; Cella, A.

    1977-01-01

    The results of the work performed under Phase I of the free piston Stirling engine demonstrator program are described. The objective of the program is to develop a 2 kW free piston Stirling engine/linear alternator energy conversion system, for an isotopic heat source, with a greater than 30% overall efficiency. Phase I was a 15-month effort to demonstrate the feasibility of the system through analysis and experimental testing of the individual components. An introduction to Stirling engines and the details of the tasks completed are presented in five major sections: (1) introduction to Stirling engine; (2) preliminary design of an advanced free piston Stirling demonstrator engine; (3) design and test of a 1 kWE output linear alternator; (4) test of a model free piston Stirling engine; and (5) development of a free piston Stirling engine computer simulation code

  13. Demonstration of a free piston Stirling engine driven linear alternator, phase I report

    Energy Technology Data Exchange (ETDEWEB)

    Goldwater, B.; Piller, S.; Rauch, J.; Cella, A.

    1977-03-30

    The results of the work performed under Phase I of the free piston Stirling engine demonstrator program are described. The objective of the program is to develop a 2 kW free piston Stirling engine/linear alternator energy conversion system, for an isotopic heat source, with a greater than 30% overall efficiency. Phase I was a 15-month effort to demonstrate the feasibility of the system through analysis and experimental testing of the individual components. An introduction to Stirling engines and the details of the tasks completed are presented in five major sections: (1) introduction to Stirling engine; (2) preliminary design of an advanced free piston Stirling demonstrator engine; (3) design and test of a 1 kWE output linear alternator; (4) test of a model free piston Stirling engine; and (5) development of a free piston Stirling engine computer simulation code.

  14. Business Case Analysis of the Joint Strike Fighter's Alternate Engine Program

    National Research Council Canada - National Science Library

    Shick, BethAnn

    2007-01-01

    .... The JSF will serve the Air Force, Navy and Marine Corps, as well as many of our key international allies In 1998, the DoD initiated the JSF alternate engine program in an effort to achieve cost...

  15. Ethanol Research : Alternative Fuels & Life-Cycle Engineering Program : November 29, 2006 to November 28, 2011

    Science.gov (United States)

    2011-12-20

    This report presents the results of the successful ethanol fuel demonstration program conducted from September 2007 to September 2010. This project was a part of the U.S. Department of Transportation (DOT) Alternative Fuels and Life Cycle Engineering...

  16. Browse Title Index

    African Journals Online (AJOL)

    1986), University Engineering Education and Training in Nigeria: Development, ... Vol 29, No 1 (2010), Use of Energy Method to Simulate the ... of Optimal Rational Composition of Titles Producible from Nigerian Clays ...

  17. Honeywell Engines, Systems and Services, Phoenix, Arizona, Dec. 10, 2007 Petition to Object to Title V Operating Permit

    Science.gov (United States)

    This document may be of assistance in applying the Title V air operating permit regulations. This document is part of the Title V Petition Database available at www2.epa.gov/title-v-operating-permits/title-v-petition-database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

  18. Alternative Pulse Detonation Engine Ignition System Investigation through Detonation Splitting

    Science.gov (United States)

    2002-03-01

    on the soccer field and later discovered is a brilliant and dedicated scientist and engineer. He’s been an inspiration and role model, who sees...designing configurations before cutting metal for an experiment reduces research time and cost. Dr. Vish Katta had built an in-house program ( UNICORN

  19. An Alternative Educational Approach for an Inorganic Chemistry Laboratory Course in Industrial and Chemical Engineering

    Science.gov (United States)

    Garces, Andres; Sanchez-Barba, Luis Fernando

    2011-01-01

    We describe an alternative educational approach for an inorganic chemistry laboratory module named "Experimentation in Chemistry", which is included in Industrial Engineering and Chemical Engineering courses. The main aims of the new approach were to reduce the high levels of failure and dropout on the module and to make the content match the…

  20. Development of Demonstrably Predictive Models for Emissions from Alternative Fuels Based Aircraft Engines

    Science.gov (United States)

    2017-05-01

    Engineering Chemistry Fundamentals, Vol. 5, No. 3, 1966, pp. 356–363. [14] Burns, R. A., Development of scalar and velocity imaging diagnostics...in an Aero- Engine Model Combustor at Elevated Pressure Using URANS and Finite- Rate Chemistry ,” 50th AIAA/ASME/SAE/ASEE Joint Propulsion Conference...FINAL REPORT Development of Demonstrably Predictive Models for Emissions from Alternative Fuels Based Aircraft Engines SERDP Project WP-2151

  1. Biodiesel as an Alternative Fuel for Diesel Engines

    OpenAIRE

    F. Halek; A. Kavousi; M. Banifatemi

    2009-01-01

    There is growing interest in biodiesel (fatty acid methyl ester or FAME) because of the similarity in its properties when compared to those of diesel fuels. Diesel engines operated on biodiesel have lower emissions of carbon monoxide, unburned hydrocarbons, particulate matter, and air toxics than when operated on petroleum-based diesel fuel. Production of fatty acid methyl ester (FAME) from rapeseed (nonedible oil) fatty acid distillate having high free fatty acids (FFA) ...

  2. Summary of the Phase II, Title I engineering assessment of inactive uranium mill tailings, Green River Site, Green River, Utah

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium mill tailings at the Green River site, Utah. The services include the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 123 thousand tons of tailings at the Green River site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The three alternative actions presented are dike stabilization, fencing, on- and off-site decontamination and maintenance; improvements in the stabilization cover and diking plus cleanup of the site and Browns Wash, and realignment of Browns Wash; and addition of stabilization cover to a total of 2 ft, realignment of Browns Wash and placement of additional riprap, on-site cleanup and drainage improvements. All options include remedial action at off-site structures. Cost estimates for the three options range from $700,000 to $926,000

  3. Summary of the Phase II, Title I engineering assessment of inactive uranium mill tailings, Spook Site, Converse County, Wyoming

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium mill tailings at the Riverton, Wyoming site. The services include: the performance of core drillings; soil, water and other sample analyses; radiometric measurements to determine areas with radium-contaminated materials; the evaluation of resulting radiation exposures of individuals and nearby populations; the investigation of site geology, hydrology, and meteorology; and the evaluation and costing of alternative corrective actions. Radon gas release from the 900,000 tons of tailings at the Riverton site constitutes the main environmental impact. The two alternative actions presented are fencing and maintenance of the site and off-site remedial action and decontamination of the millsite and ore storage areas and additional stabilization cover to a minimum of 2 ft. The cost estimates for the options are $460,000 and $1,140,000, respectively. Estimated costs for moving the tailings and all contaminated materials to unspecified sites 5 and 10 mi from the present location are $6,000,000 and $6,400,000, respectively

  4. Phase II, Title I engineering assessment of inactive uranium mill tailings, Green River Site, Green River, Utah

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium mill tailings at the Green River site, Utah. Services included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations , the investigation of site hydrology and meteorology and the evaluation and costing of alternative corrective actions. Radon gas release from the 123 thousand tons of tailings at the Green River site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The three alternative actions presented are dike stabilization, fencing, on- and off-site decontamination and maintenance (Option I); improvements in the stabilization cover and diking plus cleanup of the site and Browns Wash, and realignment of Browns Wash (Option II); and addition of stabilization cover to a total of 2 ft, realignment of Browns Wash and placement of additional riprap, on-site cleanup and drainage improvements (Option III). All options include remedial action at off-site structures. Cost estimates for the three options range from $700,000 to $926,000

  5. Phase II, Title I engineering assessment of inactive uranium mill tailings, Mexican Hat site, Mexican Hat, Utah

    International Nuclear Information System (INIS)

    1977-01-01

    An engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at the Mexican Hat millsite in Utah is presented. Topographic maps, data on core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and other radium-contaminated materials, the evaluation of resulting radiation exposures of individuals residing nearby, the investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions are presented. Radon gas release from the 2,200,000 tons of tailings on the site constitutes the most significant environmental impact. T he six alternative actions presented are directed towards restricting access to the site, returning the windblown tailings to the piles and stabilizing the piles with cover material, and consolidating the two piles into one pile and stabilizing it with cover material. Fencing around the site or the tailings and the decontamination of mill buildings is included in all options. Costs of the options range from $370,000 to $4,390,000

  6. Phase II, Title I engineering assessment of inactive uranium mill tailings, Phillips/United Nuclear Site, Ambrosia Lake, New Mexico

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium mill tailings at the Phillips/United Nuclear site at Ambrosia Lake, New Mexico. Services included the preparation of topographic maps, the performance of core drillings sufficient to determine areas and volumes of tailings, and radiometric measurements to determine radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 2.6 million tons of tailings at the Phillips/United Nuclear site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The estimated radiological health effects to the general population are considered to be minimal. The two alternative actions presented are: dike stabilization, fencing, and maintenance; and adding 2 ft of stabilization cover material. Both options include remedial action at off-site structures and on-site decontamination around the tailings pile. Cost estimates for the two options are $920,000 and $2,230,000, respectively

  7. Summary of the Phase II, Title I engineering assessment of inactive uranium mill tailing, Riverton Site, Riverton, Wyoming

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium mill tailings at the Riverton, Wyoming site. The soil, water and other sample analyses; radiometric measurements to determine areas with radium-contaminated materials; the evaluation of resulting radiation exposures of individuals and nearby populations; the investigation of site geology, hydrology, and meteorology; and the evaluation and costing of alternative corrective actions. Radon gas release from the 900,000 tons of tailings at the Riverton site constitutes the main environmental impact. The two alternative actions presented are fencing and maintenance of the site and off-site remedial action, and decontamination of the millsite and ore storage areas and additional stabilization cover to a minimum of 2 ft. The cost estimates for the options are $460,000 and $1,140,000, respectively. Estimated costs for moving the tailings and all contaminated materials to unspecified sites 5 and 10 mi from the present location are $6,000,000 and $6,400,000, respectively

  8. Evaluation of the effectiveness and feasibility of the Waste Isolation Pilot Plant engineered alternatives: Final report of the Engineered Alternatives Task Force

    International Nuclear Information System (INIS)

    1991-07-01

    The Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico, is an underground repository designed for the geologic disposal of radioactive wastes resulting from the defense activities and programs of the United States Department of Energy (DOE). The performance of nuclear waste repositories is governed by US Environmental Protection Agency (EPA). The study conducted to demonstrate compliance with this regulation is called performance assessment. The EPA standard requires that DOE provide a reasonable assurance, based on performance assessment, that cumulative releases of radioactivity to the accessible environment will not exceed the standard's criteria. Preliminary performance assessment performed by SNL has indicated that the current design of the WIPP repository, together with the waste forms at the DOE storage and generating sites, may not demonstrate compliance with the EPA Standard. In view of this concern, and prompted by recommendations from external review groups, the DOE established the Engineered Alternatives Task Force (EATF) in September, 1989. The objective of the EATF is to identify potential engineering modifications (referred to as engineered alternatives) to the existing WIPP design and/or to the transuranic (TRU) waste forms, an to evaluate their effectiveness and feasibility in facilitating compliance with the EPA Standard. These alternatives would be designed to completely eliminate or reduce any problems which might cause non-compliance with the EPA Standard. 139 refs., 39 figs., 124 tabs

  9. Castor oil biodiesel as an alternative fuel for diesel engines

    International Nuclear Information System (INIS)

    Benavides, Alirio; Benjumea, Pedro; Pashova, Veselina

    2007-01-01

    In this paper, a study related to the production and use of castor oil biodiesel is presented. The maximum methyl esters yield of the castor oil transesterification reaction is obtained under the following conditions: ambient temperature, a molar ratio of methanol to vegetable oil equal to 9 and a catalyst percentage equal to 0.8%. The castor oil biodiesel can be blended with petroleum diesel as far as 15% in such way that the resulting blend complies with national and international technical standards for diesel fuels. Its high viscosity becomes the main difficulty for using castor oil biodiesel in engines. However this biofuel exhibits excellent cold flow properties (low values of cloud and pour points). The motor tests using castor oil biodiesel petroleum diesel blends, for the biodiesel proportion tested; show that a biodiesel percentage increase leads to an increase in the specific fuel consumption, a decrease in the fuel air ratio, a slight decrease in smoke opacity, while the fuel conversion efficiency and the CO and CO 2 emissions practically remain constants

  10. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXX, I--CATERPILLAR DIESEL ENGINE MAINTENANCE SUMMARY, II--REIEWING FACTS ABOUT ALTERNATORS.

    Science.gov (United States)

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO PROVIDE A SUMMARY OF DIESEL ENGINE MAINTENANCE FACTORS AND A REVIEW OF DIESEL ENGINE ALTERNATOR OPERATION. THE SEVEN SECTIONS COVER DIESEL ENGINE TROUBLESHOOTING AND THE OPERATION, TESTING, AND ADJUSTING OF ALTERNATORS. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL BRANCH PROGRAMED TRAINING FILM…

  11. 40 CFR 1045.645 - What special provisions apply for converting an engine to use an alternate fuel?

    Science.gov (United States)

    2010-07-01

    ... converting an engine to use an alternate fuel? 1045.645 Section 1045.645 Protection of Environment... for converting an engine to use an alternate fuel? A certificate of conformity is no longer valid for.... This section applies if such modifications are done to convert the engine to run on a different fuel...

  12. 40 CFR 1054.645 - What special provisions apply for converting an engine to use an alternate fuel?

    Science.gov (United States)

    2010-07-01

    ... converting an engine to use an alternate fuel? 1054.645 Section 1054.645 Protection of Environment... apply for converting an engine to use an alternate fuel? A certificate of conformity is no longer valid... fuel type. Such engines may need to be recertified as specified in this section if the certificate is...

  13. Alternatives to electrical cogeneration: The direct application of steam engines

    International Nuclear Information System (INIS)

    Phillips, W.C.

    1993-01-01

    Although small to medium sized industrial facilities are aware of electrical cogeneration, often they are too small for it to be economically justifiable. The direct application of steam turbine power to equipment formerly powered by electric motors, can allow them to use steam capacity to reduce electrical demand and consumption, bypassing cogeneration. Cogeneration converts the heat energy of steam into circular mechanical motion and then converts the circular mechanical motion into electricity. Each conversion entails a loss of energy due to friction and other conversion losses. A substantial amount of the generated electricity is then converted back into circular motion with electric motors, again incurring energy losses. Directly applying the mechanical motion of turbines eliminates both the motion-to-electricity (generator) and the electricity-to-motion (motor) conversion losses. Excess steam capacity during the summer is not unusual for facilities that use steam to provide winter heating. Similarly, most of these facilities experience a large electrical demand peak during the cooling season due to the electricity needed to operate centrifugal chillers. Steam capacity via a turbine to power the chillers can allow the boilers to operate at a higher loading while reducing electrical consumption and demand precisely those periods when demand reduction is most needed. In facilities where the steam generating capacity is sufficient, air compressors provide an appropriate year-round application for turbine power. This paper is the result of an on-going project by the Energy Division, State of North Carolina, Department of Economic and Community Development, in conjunction with the University of North Carolina at Charlotte. The objective of this project is to educate the operating engineers and managers of small to medium sized manufacturing facilities on the technical application and economic justification of steam turbine power

  14. Demonstration of a free piston Stirling engine driven linear alternator system. Annual report

    International Nuclear Information System (INIS)

    1978-01-01

    The objective of the program is to develop a 2 kW Free Piston Stirling Engine/Linear Alternator Energy Conversion System for an isotopic heat source with a greater than 30% overall efficiency. The work was broken up into two phases. Phase I demonstrated the feasibility of the energy conversion system through analysis and experimental testing of the individual components. Phase II is a two-year effort to design, fabricate, and test a prototype demonstrator energy conversion system. The reprt documents the work performed during October 1976 through September 1977, the first year of Phase II. Details of the tasks are presented in five major sections: (1) Linear Alternator Development; (2) Engine/Alternator System Demonstration; (3) Demonstrator Preliminary Design; (4) Demonstrator Detailed Design; and (5) Development of Free Piston Stirling Engine Computer Simulation

  15. Controllability of Free-piston Stirling Engine/linear Alternator Driving a Dynamic Load

    Science.gov (United States)

    Kankam, M. David; Rauch, Jeffrey S.

    1994-01-01

    This paper presents the dynamic behavior of a Free-Piston Stirling Engine/linear alternator (FPSE/LA) driving a single-phase fractional horse-power induction motor. The controllability and dynamic stability of the system are discussed by means of sensitivity effects of variations in system parameters, engine controller, operating conditions, and mechanical loading on the induction motor. The approach used expands on a combined mechanical and thermodynamic formulation employed in a previous paper. The application of state-space technique and frequency domain analysis enhances understanding of the dynamic interactions. Engine-alternator parametric sensitivity studies, similar to those of the previous paper, are summarized. Detailed discussions are provided for parametric variations which relate to the engine controller and system operating conditions. The results suggest that the controllability of a FPSE-based power system is enhanced by proper operating conditions and built-in controls.

  16. Use of a non-edible vegetable oils as an alternative fuel in compression ignition engines

    International Nuclear Information System (INIS)

    Jayaraj, S.; Ramadhas, A.S.; Muraleedharan, C.

    2006-01-01

    Shortage of petroleum fuels is assumed predominance globally and hence efforts are being made in every country to look for alternative fuels, especially for running internal compression ignition engines. However, the limited availability of edible vegetable oils in excess amounts is a limiting factors, which limits their large usage as an alternative fuel. A remedy for this is the use of non-edible oils obtained mainly from seeds, which are otherwise dumped as waste material. An effort is made here to use rubber seed oil as fuel in compression ignition engine at various proportions, mixed with diesel oil. The performance and emission characteristics of the engine are measured under dual fuel operation. The compression ignition engine could be run satisfactorily without any noticeable problem, even with 100% rubber seed oil. A multi-layer artificial neural network model was developed for predicting the performance and emission characteristics of the engine under dual fuel operation. Experimental data has been used to train the network. The predicted engine performance and emission characteristics obtained by neural network model are validated by using the experimental data. The neural network model is found to be quite efficient in predicting engine performance and emission characteristics. It has been found that 60-80% diesel replacement by rubber seed oil is the optimum in order to get maximum engine performance and minimum exhaust emission

  17. Research Capabilities Directed to all Electric Engineering Teachers, from an Alternative Energy Model

    Directory of Open Access Journals (Sweden)

    Víctor Hugo Ordóñez Navea

    2017-08-01

    Full Text Available The purpose of this work was to contemplate research capabilities directed to all electric engineering teachers from an alternative energy model intro the explanation of a semiconductor in the National Training Program in Electricity. Some authors, such as. Vidal (2016, Atencio (2014 y Camilo (2012 point out to technological applications with semiconductor electrical devices. In this way; a diagnostic phase is presented, held on this field research as a descriptive type about: a how to identify the necessities of alternative energies, and b The research competences in the alternatives energies of researcher from a solar cell model, to boost and innovate the academic praxis and technologic ingenuity. Themselves was applied a survey for a group of 15 teachers in the National Program of Formation in electricity to diagnose the deficiencies in the research area of alternatives energies. The process of data analysis was carried out through descriptive statistic. Later the conclusions are presented the need to generate strategies for stimulate and propose exploration of alternatives energies to the development of research competences directed to the teachers of electrical engineering for develop the research competences in the enforcement of the teachers exercise for the electric engineering, from an alternative energy model and boost the technologic research in the renewal energies field.

  18. Impact of alternative fuels on the operational and environmental performance of a small turbofan engine

    International Nuclear Information System (INIS)

    Gaspar, R.M.P.; Sousa, J.M.M.

    2016-01-01

    Highlights: • A wide range of alternative fuels is studied in a small two-spool turbofan engine. • Impact of fuel properties on flame temperature and droplet evaporation considered. • Performance and pollutant emissions at different operating conditions are analyzed. • Use of alternative fuels generally leads to an improved performance of the engine. • Mostly reductions in soot emissions, but also cuts in NO_x and CO, are obtained. - Abstract: A wide range of alternative jet fuels is studied in this work for use in a small two-spool turbofan engine. These embrace the five production pathways currently approved by the American Society for Testing and Materials. Both neat products and blends (within certified limits) have been considered. The present analysis is based on a 0-D thermodynamic modeling of the aero-engine for off-design and transient simulations. In addition, the selected approach incorporates fuel effects on combustion and the impact of fuel properties on the flame temperature, as well as on the droplet evaporation rate. Predicted performance and pollutant emission outputs for the alternative fuels are presented at different operating conditions, namely: take-off, top of climb, cruise, low power and ground idle. The results are discussed and comprehensively compared with data available in the literature. It was concluded that the combustion of alternative fuels generally leads to enhancements in engine performance with respect to the use of conventional kerosene. Reductions in pollutant emissions occur mostly in soot, but also in nitrogen oxides and carbon monoxide, depending on the fuel and operating conditions. In contrast, increased emissions of unburned hydrocarbons are generally observed. Concerns about the aero-engine dynamic response are raised only in very few cases, involving the use of neat products.

  19. Platelet lysate as an autologous alternative for fetal bovine serum in cardiovascular tissue engineering

    NARCIS (Netherlands)

    Riem Vis, P.W.; Bouten, C.V.C.; Sluijter, J.P.G.; Herwerden, van L.A.; Kluin, J.

    2010-01-01

    There is an ongoing search for alternative tissue culture sera to engineer autologous tissues, since use of fetal bovine serum (FBS) is limited under Good Tissue Practice (GTP) guidelines. We compared FBS with human Platelet-lysate (PL) in media for in vitro cell culture. A threefold increase in

  20. BOOST QUALITY OF ENGINEERING PROJECT SOLUTIONS THROUGH ECONOMIC ANALYSIS AND COMPARING ALTERNATIVES

    Directory of Open Access Journals (Sweden)

    Milan Vukčević

    2008-12-01

    Full Text Available In this paper the principles and applications of money-time relationships are given. Economic profitability of engineering projects, using more methodes is analised. On the bases those methodes, comparing mutually exclusive alternatives of projects was done, because of optimization of decision. The emphasized theoretical states in this paper are applicated.

  1. Design analysis of engineered alternatives for the Waste Isolation Pilot Plant

    International Nuclear Information System (INIS)

    Myers, J.; Djordjevic, S.; Adams, M.; Spangler, L.; Valdez, J.; Vetter, D.; Drez, P.

    1991-01-01

    The effectiveness of several engineered alternatives, designed to enhance the performance of the Waste Isolation Pilot Plant (WIPP), were evaluated relative to the performance of the baseline design. This evaluation was performed using a computer program referred to as the Design Analysis Model which couples salt creep closure, brine inflow, gas generation and dissipation to realistically simulate these interrelated processes over a 10,000 year period following the decommissioning of the repository. Analyses of the baseline design and nine alternative designs were performed for the undisturbed repository conditions, as well as three human intrusion events. Improvements in repository performance of up to four orders of magnitude were predicted for various engineered alternative waste forms. 6 refs., 8 figs., 1 tab

  2. Analysis of the dynamic response improvement of a turbocharged diesel engine driven alternating current generating set

    International Nuclear Information System (INIS)

    Katrasnik, Tomaz; Medica, Vladimir; Trenc, Ferdinand

    2005-01-01

    Reliability of electric supply systems is among the most required necessities of modern society. Turbocharged diesel engine driven alternating current generating sets are often used to prevent electric black outs and/or as prime electric energy suppliers. It is well known that turbocharged diesel engines suffer from an inadequate response to a sudden load increase, this being a consequence of the nature of the energy exchange between the engine and the turbocharger. The dynamic response of turbocharged diesel engines could be improved by electric assisting systems, either by direct energy supply with an integrated starter-generator-booster (ISG) mounted on the engine flywheel, or by an indirect energy supply with an electrically assisted turbocharger. An experimentally verified zero dimensional computer simulation method was used for the analysis of both types of electrical assistance. The paper offers an analysis of the interaction between a turbocharged diesel engine and different electric assisting systems, as well as the requirements for the supporting electric motors that could improve the dynamic response of a diesel engine while driving an AC generating set. When performance class compliance is a concern, it is evident that an integrated starter-generator-booster outperforms an electrically assisted turbocharger for the investigated generating set. However, the electric energy consumption and frequency recovery times are smaller when an electrically assisted turbocharger is applied

  3. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 391 ... Journal Home > Advanced Search > Browse Title Index ... Efficacy of four Rodenticides on the Ghanaian Market, Abstract ... Vol 2, No 1 (2000):, Determination of some wear elements in used car engine oil and oil filter ...

  4. The Role of Alternative Testing Strategies in Environmental Risk Assessment of Engineered Nanomaterials

    OpenAIRE

    Hjorth, Rune; Holden, Patricia; Hansen, Steffen Foss; Colman, Ben; Grieger, Khara; Hendren, Christine

    2017-01-01

    Within toxicology there is a pressure to find new test systems and organisms to replace, reduce and refine animal testing. In nanoecotoxicology the need for alternative testing strategies (ATS) is further emphasized as the validity of tests and risk assessment practices developed for dissolved chemicals are challenged. Nonetheless, standardized whole organism animal testing is still considered the gold standard for environmental risk assessment. Advancing risk analysis of engineered nanomater...

  5. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 985 ... Journal Home > Advanced Search > Browse Title Index ... Vol 17 (2010), Alternating Direction Implicit Finite Difference Time Domain Acoustic Wave Algorithm, Abstract. E Ikata .... Vol 17 (2010), Analytic derivation of the wave profile and phase speed of sixth order Stokes waves in deep water, Abstract.

  6. Development And Testing Of Biogas-Petrol Blend As An Alternative Fuel For Spark Ignition Engine

    Directory of Open Access Journals (Sweden)

    Awogbemi

    2015-08-01

    Full Text Available Abstract This research is on the development and testing of a biogas-petrol blend to run a spark ignition engine. A2080 ratio biogaspetrol blend was developed as an alternative fuel for spark ignition engine test bed. Petrol and biogas-petrol blend were comparatively tested on the test bed to determine the effectiveness of the fuels. The results of the tests showed that biogas petrol blend generated higher torque brake power indicated power brake thermal efficiency and brake mean effective pressure but lower fuel consumption and exhaust temperature than petrol. The research concluded that a spark ignition engine powered by biogas-petrol blend was found to be economical consumed less fuel and contributes to sanitation and production of fertilizer.

  7. Successful and failing challengers: Diesel and steam as alternatives to the gasoline automotive engine

    Energy Technology Data Exchange (ETDEWEB)

    Haard, M. [Norwegian Univ. of Science and Technology (Norway). Centre for Technology and Society; Jamison, A. [Lund Univ. (Sweden). Research Policy Inst.

    1996-07-01

    This paper aims at explaining why it is that some technologies become so entrenched in our society that it becomes virtually impossible to alter them, and why some challengers nevertheless succeed. It attempts to show that it is seldom enough to explain success and failure by reference to technical factors. By means of an historically comparative analysis of two challengers to the automobile gasoline engine - steam and diesel, the paper tries to show that history can help us understand and perhaps amend the problems that contemporary politicians and other social actors experience in trying to find niches for unconventional technologies. The central thesis is that established technologies remain because they have gained symbolic power, are carried by deeply embedded organizational structures, and have helped to create strong behavioral patterns. An alternative technology seldom succeeds if it poses an alternative at all three levels; indeed, the contention is that a too ambitious alternative is less likely to succeed than a conservative one. In this particular case, the diesel slowly but surely rid itself of the symbolism that had for a long time put it at a disadvantage compared to the gasoline engine; it was taken up by the same actors and organizations that supported the gasoline engine; its engineers managed to provide users with functions that were so familiar that they did not have to change their set patterns of behavior. The steamer, by contrast, did not succeed in any of these respects; its meaning came to be associated (negatively) with high fuel consumption; its organizational affiliations were weak; and users were never given the opportunity to test their willingness to modify their behavior. 50 refs

  8. Modification Design of Petrol Engine for Alternative Fueling using Compressed Natural Gas

    Directory of Open Access Journals (Sweden)

    Eliezer Uchechukwu Okeke

    2013-04-01

    Full Text Available This paper is on the modification design of petrol engine for alternative fuelling using Compressed Natural Gas (CNG. It provides an analytical background in the modification design process. A petrol engine Honda CR-V 2.0 auto which has a compression ratio of 9.8 was selected as case study. In order for this petrol engine to run on CNG, its compression had to be increased. An optimal compression ratio of 11.97 was computed using the standard temperature-specific volume relationship for an isentropic compression process. This computation of compression ratio is based on an inlet air temperature of 30oC (representative of tropical ambient condition and pre-combustion temperature of 540oC (corresponding to the auto-ignition temperature of CNG. Using this value of compression ratio, a dimensional modification Quantity =1.803mm was obtained using simple geometric relationships. This value of 1.803mm is needed to increase the length of the connecting rod, the compression height of the piston or reducing the sealing plate’s thickness. After the modification process, a CNG engine of air standard efficiency 62.7% (this represents a 4.67% increase over the petrol engine, capable of a maximum power of 83.6kW at 6500rpm, was obtained.

  9. Applicability of dimethyl ether (DME) in a compression ignition engine as an alternative fuel

    International Nuclear Information System (INIS)

    Park, Su Han; Lee, Chang Sik

    2014-01-01

    Highlights: • Overall characteristics of DME fueled engine are reviewed. • Fuel properties characteristics of DME are introduced. • New technologies for DME vehicle are systemically reviewed. • Research trends for the development of DME vehicle in the world are introduced. - Abstract: From the perspectives of environmental conservation and energy security, dimethyl-ether (DME) is an attractive alternative to conventional diesel fuel for compression ignition (CI) engines. This review article deals with the application characteristics of DME in CI engines, including its fuel properties, spray and atomization characteristics, combustion performance, and exhaust emission characteristics. We also discuss the various technological problems associated with its application in actual engine systems and describe the field test results of developed DME-fueled vehicles. Combustion of DME fuel is associated with low NO x , HC, and CO emissions. In addition, PM emission of DME combustion is very low due to its molecular structure. Moreover, DME has superior atomization and vaporization characteristics than conventional diesel. A high exhaust gas recirculation (EGR) rate can be used in a DME engine to reduce NO x emission without any increase in soot emission, because DME combustion is essentially soot-free. To decrease NO x emission, engine after-treatment devices, such as lean NO x traps (LNTs), urea-selective catalytic reduction, and the combination of EGR and catalyst have been applied. To use DME fuel in automotive vehicles, injector design, fuel feed pump, and the high-pressure injection pump have to be modified, combustion system components, including sealing materials, have to be rigorously designed. To use DME fuel in the diesel vehicles, more research is required to enhance its calorific value and engine durability due to the low lubricity of DME, and methods to reduce NO x emission are also required

  10. Development of a non-engine fuel injector deposit test for alternative fuels (ENIAK-project)

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmann, Hajo; Pohland vom Schloss, Heide [OWI - Oel Waerme Institut GmbH, Herzogenrath (Germany)

    2013-06-01

    Deposit formation in and on the injectors of diesel engines may lead to injector malfunction, resulting in a loss in power, rough engine operation and poor emission levels. Poor Biodiesel quality, contamination with copper and zinc as well as undesired reactions between (several) additives and biodiesel components are known causes for nozzle fouling. Therefore, good housekeeping when using biodiesel is required, and all additives have to pass a no-harm test concerning injector fouling. The standard fouling tests are two engine tests: The XUD9-test (CEC F-23-01) and the DW-10-test (CEC DF 98-08). The XUD9 is a cost efficient, fast and proven testing method. It uses, however, an obsolete indirect injection diesel engine and cannot reproduce internal diesel injector deposits (IDID). The newer DW10 test is complex, costly and designed for high stress. This reduces the engine life and leads to a fuel consumption of approximately 1,000 1 per test, both contributing to the high costs of the test. The ENIAK-Project is funded by the FNR (''Fachagentur Nachwachsende Rohstoffe'', Agency for Renewable Resources) and conducted in cooperation with AGQM, ASG and ERC. Its main goal is the development, assembly, commissioning, and evaluation of a non-engine fuel injector test. It uses a complete common rail system. The injection takes place in a self-designed reactor instead of an engine, and the fuel is not combusted, but re-condensed and pumped in a circle, leading to a low amount of fuel required. If the test method proves to be as reliable as expected, it can be used as an alternative test method for injector fouling with low requirements regarding infrastructure on the testing site and sample volume. (orig.)

  11. Biodiesel from plant seed oils as an alternate fuel for compression ignition engines-a review.

    Science.gov (United States)

    Vijayakumar, C; Ramesh, M; Murugesan, A; Panneerselvam, N; Subramaniam, D; Bharathiraja, M

    2016-12-01

    The modern scenario reveals that the world is facing energy crisis due to the dwindling sources of fossil fuels. Environment protection agencies are more concerned about the atmospheric pollution due to the burning of fossil fuels. Alternative fuel research is getting augmented because of the above reasons. Plant seed oils (vegetable oils) are cleaner, sustainable, and renewable. So, it can be the most suitable alternative fuel for compression ignition (CI) engines. This paper reviews the availability of different types of plant seed oils, several methods for production of biodiesel from vegetable oils, and its properties. The different types of oils considered in this review are cashew nut shell liquid (CNSL) oil, ginger oil, eucalyptus oil, rice bran oil, Calophyllum inophyllum, hazelnut oil, sesame oil, clove stem oil, sardine oil, honge oil, polanga oil, mahua oil, rubber seed oil, cotton seed oil, neem oil, jatropha oil, egunsi melon oil, shea butter, linseed oil, Mohr oil, sea lemon oil, pumpkin oil, tobacco seed oil, jojoba oil, and mustard oil. Several methods for production of biodiesel are transesterification, pre-treatment, pyrolysis, and water emulsion are discussed. The various fuel properties considered for review such as specific gravity, viscosity, calorific value, flash point, and fire point are presented. The review also portrays advantages, limitations, performance, and emission characteristics of engine using plant seed oil biodiesel are discussed. Finally, the modeling and optimization of engine for various biofuels with different input and output parameters using artificial neural network, response surface methodology, and Taguchi are included.

  12. Emissions from Petrol Engine Fueled Gasoline–Ethanol–Methanol (GEM Ternary mixture as Alternative Fuel

    Directory of Open Access Journals (Sweden)

    Thangavelu Saravana Kannan

    2015-01-01

    Full Text Available The increasing demands of petroleum fuels due to the rapid development automotive society coupled with the environmental pollution issues have inspired the efforts on exploring alternative fuels for internal combustion engines. Bioethanol obtained from biomass and bioenergy crops has been proclaimed as one of the feasible alternative to gasoline. In this study, the effect of gasoline–ethanol–methanol (GEM ternary blend on the emission characteristics of petrol engine was studied. Three different fuel blends, namely, E0 (gasoline, G75E21M4 (75% gasoline, 21% hydrous ethanol and 4% methanol and E25 (25% anhydrous ethanol and 75% gasoline were tested in a 1.3-l K3-VE spark-ignition engine. The results indicate that, when G75E21M4 fuel blend was used, a significant drop in CO, CO2, NOx and HC emissions by about 42%, 15%, 7% and 5.2% compared to E0, respectively. Moreover, the emission results for G75E21M4 are marginally lower than E25 whereas; HC emission was slightly higher than E25.

  13. Identification of future engineering-development needs of alternative concepts for magnetic-fusion energy

    International Nuclear Information System (INIS)

    Krakowski, R.A.

    1982-01-01

    A qualitative identification of future engineering needs of alternative fusion concepts (AFCs) is presented. These needs are assessed relative to the similar needs of the tokamak in order to emphasize differences in required technology with respect to the well documented mainline approach. Although nearly thirty AFCs can be identified as being associated with some level of reactor projection, redirection, refocusing, and general similarities can be used to generate a reduced AFC list that includes only the bumpy tori, stellarators, reversed-field pinches, and compact toroids. Furthermore, each AFC has the potential of operating as a conventional (low power density, superconducting magnets) or a compact, high-power-density (HPD) system. Hence, in order to make tractable an otherwise difficult task, the future engineering needs for the AFCs are addressed here for conventional versus compact approaches, with the latter being treated as a generic class and the former being composed of bumpy tori, stellarators, reversed-field pinches, and compact toroids

  14. Efficiency and exhaust gas analysis of variable compression ratio spark ignition engine fuelled with alternative fuels

    Energy Technology Data Exchange (ETDEWEB)

    Seshaiah, N. [Mechanical Engineering Department, M.I.T.S, Madanapalle, Angallu-517325, A.P. (India)

    2010-07-01

    Considering energy crises and pollution problems today, investigations have been concentrated on decreasing fuel consumption by using alternative fuels and on lowering the concentration of toxic components in combustion products. In the present work, the variable compression ratio spark ignition engine designed to run on gasoline has been tested with pure gasoline, LPG (Isobutene), and gasoline blended with ethanol 10%, 15%, 25% and 35% by volume. Also, the gasoline mixed with kerosene at 15%, 25% and 35% by volume without any engine modifications has been tested and presented the result. Brake thermal and volumetric efficiency variation with brake load is compared and presented. CO and CO2 emissions have been also compared for all tested fuels.

  15. Experimental investigations on mixing of two biodiesels blended with diesel as alternative fuel for diesel engines

    Directory of Open Access Journals (Sweden)

    K. Srithar

    2017-01-01

    Full Text Available The world faces the crises of energy demand, rising petroleum prices and depletion of fossil fuel resources. Biodiesel has obtained from vegetable oils that have been considered as a promising alternate fuel. The researches regarding blend of diesel and single biodiesel have been done already. Very few works have been done with the combination of two different biodiesel blends with diesel and left a lot of scope in this area. The present study brings out an experiment of two biodiesels from pongamia pinnata oil and mustard oil and they are blended with diesel at various mixing ratios. The effects of dual biodiesel works in engine and exhaust emissions were examined in a single cylinder, direct injection, air cooled and high speed diesel engine at various engine loads with constant engine speed of 3000 rpm. The influences of blends on CO, CO2, HC, NOx and smoke opacity were investigated by emission tests. The brake thermal efficiency of blend A was found higher than diesel. The emissions of smoke, hydro carbon and nitrogen oxides of dual biodiesel blends were higher than that of diesel. But the exhaust gas temperature for dual biodiesel blends was lower than diesel.

  16. Engineering evaluation of alternatives for the disposition of Niagara Falls Storage Site, its residues and wastes

    International Nuclear Information System (INIS)

    1984-01-01

    The final disposition scenarios selected by DOE for assessment in this document are consistent with those stated in the Notice of Intent to prepare an Environmental Impact Statement (EIS) for the Niagara Falls Storage Site (NFSS) (DOE, 1983d) and the modifications to the alternatives resulting from the public scoping process. The scenarios are: take no action beyond interim remedial measures other than maintenance and surveillance of the NFSS; retain and manage the NFSS as a long-term waste management facility for the wastes and residues on the site; decontaminate, certify, and release the NFSS for other use, with long-term management of the wastes and residues at other DOE sites; and partially decontaminate the NFSS by removal and transport off site of only the more radioactive residues, and upgrade containment of the remaining wastes and residues on site. The objective of this document is to present to DOE the conceptual engineering, occupational radiation exposure, construction schedule, maintenance and surveillance requirements, and cost information relevant to design and implementation of each of the four scenarios. The specific alternatives within each scenario used as the basis for discussion in this document were evaluated on the bases of engineering considerations, technical feasibility, and regulatory requirements. Selected alternatives determined to be acceptable for each of the four final disposition scenarios for the NFSS were approved by DOE to be assessed and costed in this document. These alternatives are also the subject of the EIS for the NFSS currently being prepared by Argonne National Laboratory (ANL). 40 figures, 38 tables

  17. Performance of a small-scale turbojet engine fed with traditional and alternative fuels

    International Nuclear Information System (INIS)

    Badami, M.; Nuccio, P.; Pastrone, D.; Signoretto, A.

    2014-01-01

    Highlights: • One synthetic fuel, one bio-fuel blend and one traditional kerosene were tested on a small-scale turbojet. • The three fuels were characterized and their chemical and physical specifications were compared. • The experimental results, in term of CO, UHC and NO x emissions, are discussed. • Emissions are compared with CFD analysis and semi-empirical equations found in literature. - Abstract: The growing use of aeronautical fuels, together with the increasing attention towards reduced environmental impact technologies, are driving governments and aeronautical companies to search for alternative aeronautical fuels to petroleum based kerosene. Analysis and measurements on real aeronautical turbines are complex and expensive; for this reason the use of parts of real engines or small size turbojets can be very interesting for research activities. The present paper describes the results of an experimental and numerical activity, regarding the influence of alternative fuels on the performance in term of emissions, on a small-scale turbojet engine with a nominal thrust of 80 N at 80,000 rpm. Three different fuels, a traditional Jet-A kerosene, a synthetic Gas To Liquid (GTL) fuel and a blend of 30% Jatropha Methyl Ester (JME) and 70% Jet-A, were tested. The experimental results, in term of CO, UHC and NO x emissions, are discussed and compared with results obtained from CFD analysis and from semi-empirical equations found in literature

  18. Metabolic engineering of Corynebacterium glutamicum aimed at alternative carbon sources and new products

    Directory of Open Access Journals (Sweden)

    Volker Fritz Wendisch

    2012-10-01

    Full Text Available Corynebacterium glutamicum is well known as the amino acid-producing workhorse of fermentation industry, being used for multi-million-ton scale production of glutamate and lysine for more than 60 years. However, it is only recently that extensive research has focused on engineering it beyond the scope of amino acids. Meanwhile, a variety of corynebacterial strains allows access to alternative carbon sources and/or allows production of a wide range of industrially relevant compounds. Some of these efforts set new standards in terms of titers and productivities achieved whereas others represent a proof-of-principle. These achievements manifest the position of C. glutamicum as an important industrial microorganism with capabilities far beyond the traditional amino acid production. In this review we focus on the state of the art of metabolic engineering of C. glutamicum for utilization of alternative carbon sources, (e.g. coming from wastes and unprocessed sources, and construction of C. glutamicum strains for production of new products such as diamines, organic acids and alcohols.

  19. Testing and preformance measurement of straight vegetable oils as an alternative fuel for diesel engines

    Science.gov (United States)

    Lakshminarayanan, Arunachalam

    Rising fuel prices, growing energy demand, concerns over domestic energy security and global warming from greenhouse gas emissions have triggered the global interest in bio-energy and bio-fuel crop development. Backlash from these concerns can result in supply shocks of traditional fossil fuels and create immense economic pressure. It is thus widely argued that bio-fuels would particularly benefit developing countries by off-setting their dependencies on imported petroleum. Domestically, the transportation sector accounts for almost 40% of liquid fuel consumption, while on-farm application like tractors and combines for agricultural purposes uses close to an additional 18%. It is estimated that 40% of the farm budget can be attributed to the fuel costs. With the cost of diesel continuously rising, farmers are now looking at using Straight Vegetable Oil (SVO) as an alternative fuel by producing their own fuel crops. This study evaluates conventional diesel compared to the use of SVO like Camelina, Canola and Juncea grown on local farms in Colorado for their performance and emissions on a John Deere 4045 Tier-II engine. Additionally, physical properties like density and viscosity, metal/mineral content, and cold flow properties like CFPP and CP of these oils were measured using ASTM standards and compared to diesel. It was found that SVOs did not show significant differences compared to diesel fuel with regards to engine emissions, but did show an increase in thermal efficiency. Therefore, this study supports the continued development of SVO production as a viable alternative to diesel fuels, particularly for on-farm applications. The need for providing and developing a sustainable, economic and environmental friendly fuel alternative has taken an aggressive push which will require a strong multidisciplinary education in the field of bio-energy. Commercial bio-energy development has the potential to not only alleviate the energy concerns, but also to give renewed

  20. Teaching physics using project-based engineering curriculum with a theme of alternative energy

    Science.gov (United States)

    Tasior, Bryan

    The Next Generation Science Standards (NGSS) provide a new set of science standards that, if adopted, shift the focus from content knowledge-based to skill-based education. Students will be expected to use science to investigate the natural world and solve problems using the engineering design process. The world also is facing an impending crisis related to climate, energy supply and use, and alternative energy development. Education has an opportunity to help provide the much needed paradigm shift from our current methods of providing the energy needs of society. The purpose of this research was to measure the effectiveness of a unit that accomplishes the following objectives: uses project-based learning to teach the engineering process and standards of the NGSS, addresses required content expectations of energy and electricity from the HSCE's, and provides students with scientific evidence behind issues (both environmental and social/economic) relating to the energy crisis and current dependence of fossil fuels as our primary energy source. The results of the research indicate that a physics unit can be designed to accomplish these objectives. The unit that was designed, implemented and reported here also shows that it was highly effective at improving students' science content knowledge, implementing the engineering design standards of the NGSS, while raising awareness, knowledge and motivations relating to climate and the energy crisis.

  1. Evaluation of hazelnut kernel oil of Turkish origin as alternative fuel in diesel engines

    International Nuclear Information System (INIS)

    Gumus, M.

    2008-01-01

    In the present study, hazelnut kernel oil of Turkish origin was evaluated as alternative fuel in a diesel engine. Potential hazelnut production throughout the world and the status of Turkey were examined. Hazelnut (Corylus avellana L.) kernel oil was transesterified with methanol using potassium hydroxide as catalyst to obtain hazelnut kernel oil methyl ester (HOME) and a comprehensive experimental investigation was carried out to examine performance and emissions of a direct injection diesel engine running with HOME and its blends with diesel fuel. Experimental parameters included the percentage of HOME in the blend, engine load, injection timing, compression ratio, and injector. The cost analysis of HOME production comparing to the price of conventional diesel fuel was performed for last decade was performed. Results showed that HOME and its blends with diesel fuel are generally comparable to diesel fuel and small modifications such as increasing injection timing, compression ratio and injector opening pressure provide significant improvement in performance and emissions. It is also expected that the price of HOME will be lower than the price of conventional diesel fuel in the near future. (author)

  2. Jatropha oil methyl ester and its blends used as an alternative fuel in diesel engine

    Directory of Open Access Journals (Sweden)

    Yarrapathruni Rao Hanumantha Venkata

    2009-01-01

    Full Text Available Biomass derived vegetable oils are quite promising alternative fuels for agricultural diesel engines. Use of vegetable oils in diesel engines leads to slightly inferior performance and higher smoke emissions due to their high viscosity. The performance of vegetable oils can be improved by modifying them through the transesterification process. In this present work, the performance of single cylinder water-cooled diesel engine using methyl ester of jatropha oil as the fuel was evaluated for its performance and exhaust emissions. The fuel properties of biodiesel such as kinematic viscosity, calorific value, flash point, carbon residue, and specific gravity were found. Results indicate that B25 has closer performance to diesel and B100 has lower brake thermal efficiency mainly due to its high viscosity compared to diesel. The brake thermal efficiency for biodiesel and its blends was found to be slightly higher than that of diesel fuel at tested load conditions and there was no difference of efficiency between the biodiesel and its blended fuels. For jatropha biodiesel and its blended fuels, the exhaust gas temperature increased with the increase of power and amount of biodiesel. However, its diesel blends showed reasonable efficiency, lower smoke, and CO2 and CO emissions.

  3. Lemon peel oil – A novel renewable alternative energy source for diesel engine

    International Nuclear Information System (INIS)

    Ashok, B.; Thundil Karuppa Raj, R.; Nanthagopal, K.; Krishnan, Rahul; Subbarao, Rayapati

    2017-01-01

    Highlights: • Novel biofuel is extracted from lemon peels through steam distillation process. • Lemon peel oil is found to be a potential, renewable alternate eco-friendly fuel. • Significant vibration is observed with 100% lemon peel oil. • Reduction of CO, HC and smoke emission are observed with lemon peel oil blends. • Lemon peel oil blends are showed higher brake thermal efficiency than diesel fuel. - Abstract: The present research work has embarked on to exploit the novel renewable and biodegradable source of energy from lemon fruit rinds. A systematic approach has been made in this study to find the suitability of lemon peel oil for internal combustion engines and gensets applications. Extracted lemon peel oil is found to exhibit comparatively very low viscosity, flash point and boiling point than that of conventional diesel. Various blends of lemon peel oil have been prepared with conventional diesel with volumetric concentration of 20%, 40%, 50% and 100% and their physical and chemical properties are evaluated for its suitability in direct injection diesel engine. Lower cetane index of lemon peel oil significantly influences the ignition delay period and peak heat release rate that lead to the penalty in NOx emissions. Interestingly, the diesel engine performance characteristics have been improved to a remarkable level with higher proportions of lemon peel oil in the blends. In addition, the reduction of BSCO, BSHC and smoke emission is proportional to the lemon oil concentration in the blends. Overall diesel engine characteristics indicated that lemon peel oil can partially or completely replace the petroleum diesel usage to a great extent in developing countries like India.

  4. Esters of ricebran oil with short chain alcohols as alternative fuel for diesel engines

    Directory of Open Access Journals (Sweden)

    F.A. Zaher

    2016-06-01

    Full Text Available The potential of ricebran oil as a feedstock for the production of a fuel for diesel engines alternative to regular diesel fuel has been assessed. Esterification rate of crude ricebran oil with methyl alcohol was studied using different volumetric ratios of alcohol to oil, different catalyst loads and catalyst types. Catalysts used were sulfuric acid at a concentration of 2% of the oil/alcohol mixture in addition to hydrochloric acid and Amberlite IR-120 cation exchange resin at the same molar concentration of H+ as in case of sulfuric acid. The reaction was fastest using sulfuric acid which has been then used to prepare esters of ricebran oil with methyl, ethyl, propyl and butyl alcohols. The four products have been evaluated as a fuel for diesel engines according to their fuel properties compared to regular diesel fuel. These properties include the calorific value, flash point, viscosity, pour point, cetane number, sulfur content and ASTM distillation characteristics. The results have shown that the methyl as well as the ethyl esters have the closest properties to those of regular diesel fuel. Diesel engine performance using blends of regular diesel fuel with methyl and ethyl esters of ricebran oil have been tested and compared to that using regular diesel fuel. The results have shown that the engine performance using a blend of 50% regular diesel fuel and 50% methyl esters of ricebran oil is better than that using regular diesel fuel. The brake thermal efficiency at full load was 30.2% using the fuel blend compared to 27.5% in case of regular fuel.

  5. Medical record search engines, using pseudonymised patient identity: an alternative to centralised medical records.

    Science.gov (United States)

    Quantin, Catherine; Jaquet-Chiffelle, David-Olivier; Coatrieux, Gouenou; Benzenine, Eric; Allaert, François-André

    2011-02-01

    The purpose of our multidisciplinary study was to define a pragmatic and secure alternative to the creation of a national centralised medical record which could gather together the different parts of the medical record of a patient scattered in the different hospitals where he was hospitalised without any risk of breaching confidentiality. We first analyse the reasons for the failure and the dangers of centralisation (i.e. difficulty to define a European patients' identifier, to reach a common standard for the contents of the medical record, for data protection) and then propose an alternative that uses the existing available data on the basis that setting up a safe though imperfect system could be better than continuing a quest for a mythical perfect information system that we have still not found after a search that has lasted two decades. We describe the functioning of Medical Record Search Engines (MRSEs), using pseudonymisation of patients' identity. The MRSE will be able to retrieve and to provide upon an MD's request all the available information concerning a patient who has been hospitalised in different hospitals without ever having access to the patient's identity. The drawback of this system is that the medical practitioner then has to read all of the information and to create his own synthesis and eventually to reject extra data. Faced with the difficulties and the risks of setting up a centralised medical record system, a system that gathers all of the available information concerning a patient could be of great interest. This low-cost pragmatic alternative which could be developed quickly should be taken into consideration by health authorities. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

  6. Alternative Pathways to Engineering Success--Using Academic and Social Integration to Understand Two-Year Engineering Student Success

    Science.gov (United States)

    Marra, Rose M.; Tsai, Chia-Lin; Bogue, Barbara; Pytel, Jean Landa

    2015-01-01

    The need for educating engineers in the United States continues as the projected demand is rising the number of high school seniors planning to enter engineering careers has remained relatively stable (Sargent, 2014). Additionally, figures show that attrition rates in undergraduate engineering continue to be an area of concern, (Sargent, 2014;…

  7. INIS: Authority List for Journal Titles

    International Nuclear Information System (INIS)

    1992-01-01

    This is the nineteenth revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). It lists 10,797 journal titles which have contained articles within the scope of INIS. The purpose of this Authority List is to provide descriptive cataloguers with a standard abbreviation for journal titles and to assist users of INIS products with a tool for verifying the full title of a journal. A journal, or periodical, is generally published within a defined, fixed interval between issues, which usually has more than one issue a year, and which usually includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as Annual Review of Nuclear Science are included. Series titles as, for example the McGraw-Hill Series in Nuclear Engineering, are not included in this Authority. Entries: Each entry consists of: - the full journal title (highlighted); - the abbreviated title; - ISSN, if available; - CODEN, if available; - additional information related to the journal title. Arrangement: In Part I, the full journal titles are grouped by country or international organization name and ordered alphabetically, followed by the ISSN, the CODEN in square brackets if available, and then the abbreviated title. The abbreviated title is based on the rules of ISO 4: Documentation - International Code for the Abbreviation of Titles of Periodicals. The abbreviations of the words are taken from the ISDS List of Periodical Title Word Abbreviation. In Part II, the order of the citations is reversed: the abbreviated journal titles are arranged alphabetically, followed by country code. Then the full journal titles are followed by the country of publication, and if available, ISSN and CODEN. Additional Information: There is important information related to the journal titles which are fundamental for tracing the history of the title and the present status. They are listed below and are entered whenever applicable: - Ceased publication; - Superseded by

  8. Comparative evaluation of three alternative power cycles for waste heat recovery from the exhaust of adiabatic diesel engines

    Science.gov (United States)

    Bailey, M. M.

    1985-01-01

    Three alternative power cycles were compared in application as an exhaust-gas heat-recovery system for use with advanced adiabatic diesel engines. The power cycle alternatives considered were steam Rankine, organic Rankine with RC-1 as the working fluid, and variations of an air Brayton cycle. The comparison was made in terms of fuel economy and economic payback potential for heavy-duty trucks operating in line-haul service. The results indicate that, in terms of engine rated specific fuel consumption, a diesel/alternative-power-cycle engine offers a significant improvement over the turbocompound diesel used as the baseline for comparison. The maximum imporvement resulted from the use of a Rankine cycle heat-recovery system in series with turbocompounding. The air Brayton cycle alternatives studied, which included both simple-cycle and compression-intercooled configurations, were less effective and provided about half the fuel consumption improvement of the Rankine cycle alternatives under the same conditions. Capital and maintenance cost estimates were also developed for each of the heat-recovery power cycle systems. These costs were integrated with the fuel savings to identify the time required for net annual savings to pay back the initial capital investment. The sensitivity of capital payback time to arbitrary increases in fuel price, not accompanied by corresponding hardware cost inflation, was also examined. The results indicate that a fuel price increase is required for the alternative power cycles to pay back capital within an acceptable time period.

  9. Engineering behavior of small-scale foundation piers constructed from alternative materials

    Science.gov (United States)

    Prokudin, Maxim Mikhaylovich

    Testing small-scale prototype pier foundations to evaluate engineering behavior is an alternative to full-scale testing that facilitates testing of several piers and pier groups at relatively low cost. In this study, various pier systems and pier groups at one tenth scale were subjected to static vertical loading under controlled conditions to evaluate stiffness, bearing capacity, and group efficiency. Pier length, material properties and methods of installation were evaluated. Pier length to diameter ratios varied between four and eight. A unique soil pit with dimensions of 2.1 m in width, 1.5 m in length and 2.0 m in depth was designed to carry out this research. The test pit was filled with moisture conditioned and compacted Western Iowa loess. A special load test frame was designed and fabricated to provide up to 25,000 kg vertical reaction force for load testing. A load cell and displacement instrumentation was setup to capture the load test data. Alternative materials to conventional cement concrete were studied. The pier materials evaluated in this study included compacted aggregate, cement stabilized silt, cementitious grouts, and fiber reinforced silt. Key findings from this study demonstrated that (1) the construction method influences the behavior of aggregate piers, (2) the composition of the pier has a significant impact on the stiffness, (3) group efficiencies were found to be a function of pier length and pier material, (4) in comparison to full-scale testing the scaled piers were found to produce a stiffer response with load-settlement and bearing capacities to be similar. Further, although full-scale test results were not available for all pier materials, the small-scale testing provided a means for comparing results between pier systems. Finally, duplicate pier tests for a given length and material were found to be repeatable.

  10. ICPP injection well alternative project, Idaho National Engineering Laboratory. Final report

    International Nuclear Information System (INIS)

    1980-10-01

    The Idaho Chemical Processing Plant (ICPP) portion of the Idaho National Engineering Laboratory (INEL) has been obtaining water needed for its operations from the Snake River aquifer, which occupies the entire region underlying the site. Most of this water has been used for cooling operating equipment, while a small portion has found various process uses. After passing through the ICPP process area, these waters are then returned to the aquifer. A small portion (about 1%) of the returned stream contains measurable amounts of radioactivity derived from the miscellaneous process users. This report and the recommendations contained herein are based upon stream flows projected for 1985 as supplied by DOE for the ICPP. 26 different alternatives for handling cooling water, chemical, and low level radioactive water disposal are examined. These cases are considered from technical, environmental, safety, and economic points of view. The level of detail is sufficient to eliminate non-viable cases, and to identify those which offer improvements over present practice. The Environmental/Safety Risk Factors were evaluated on a qualitative comparison basis only. Before a recommended improvement is incorporated into the waste disposal system, a conceptual design study should be made which would evaluate all those secondary effects and environmental factors that, by the very nature of the screening process, this study has not provided. Certain synergistic combinations have been noted and are discussed. This report does note whether the operations considered are in regulatory compliance, or are likely to be capable of providing lasting improvement to the waste water system. Qualitative comparisons were made between the various alternatives to confirm their relationship with applicable standards

  11. Polycyclic aromatic hydrocarbon emissions from the combustion of alternative fuels in a gas turbine engine.

    Science.gov (United States)

    Christie, Simon; Raper, David; Lee, David S; Williams, Paul I; Rye, Lucas; Blakey, Simon; Wilson, Chris W; Lobo, Prem; Hagen, Donald; Whitefield, Philip D

    2012-06-05

    We report on the particulate-bound polycyclic aromatic hydrocarbons (PAH) in the exhaust of a test-bed gas turbine engine when powered by Jet A-1 aviation fuel and a number of alternative fuels: Sasol fully synthetic jet fuel (FSJF), Shell gas-to-liquid (GTL) kerosene, and Jet A-1/GTL 50:50 blended kerosene. The concentration of PAH compounds in the exhaust emissions vary greatly between fuels. Combustion of FSJF produces the greatest total concentration of PAH compounds while combustion of GTL produces the least. However, when PAHs in the exhaust sample are measured in terms of the regulatory marker compound benzo[a]pyrene, then all of the alternative fuels emit a lower concentration of PAH in comparison to Jet A-1. Emissions from the combustion of Jet A-1/GTL blended kerosene were found to have a disproportionately low concentration of PAHs and appear to inherit a greater proportion of the GTL emission characteristics than would be expected from volume fraction alone. The data imply the presence of a nonlinear relation between fuel blend composition and the emission of PAH compounds. For each of the fuels, the speciation of PAH compounds present in the exhaust emissions were found to be remarkably similar (R(2) = 0.94-0.62), and the results do provide evidence to support the premise that PAH speciation is to some extent indicative of the emission source. In contrast, no correlation was found between the PAH species present in the fuel with those subsequently emitted in the exhaust. The results strongly suggests that local air quality measured in terms of the particulate-bound PAH burden could be significantly improved by the use of GTL kerosene either blended with or in place of Jet A-1 kerosene.

  12. Alternative Conformations of the Tau Repeat Domain in Complex with an Engineered Binding Protein*

    Science.gov (United States)

    Grüning, Clara S. R.; Mirecka, Ewa A.; Klein, Antonia N.; Mandelkow, Eckhard; Willbold, Dieter; Marino, Stephen F.; Stoldt, Matthias; Hoyer, Wolfgang

    2014-01-01

    The aggregation of Tau into paired helical filaments is involved in the pathogenesis of several neurodegenerative diseases, including Alzheimer disease. The aggregation reaction is characterized by conformational conversion of the repeat domain, which partially adopts a cross-β-structure in the resulting amyloid-like fibrils. Here, we report the selection and characterization of an engineered binding protein, β-wrapin TP4, targeting the Tau repeat domain. TP4 was obtained by phage display using the four-repeat Tau construct K18ΔK280 as a target. TP4 binds K18ΔK280 as well as the longest isoform of human Tau, hTau40, with nanomolar affinity. NMR spectroscopy identified two alternative TP4-binding sites in the four-repeat domain, with each including two hexapeptide motifs with high β-sheet propensity. Both binding sites contain the aggregation-determining PHF6 hexapeptide within repeat 3. In addition, one binding site includes the PHF6* hexapeptide within repeat 2, whereas the other includes the corresponding hexapeptide Tau(337–342) within repeat 4, denoted PHF6**. Comparison of TP4-binding with Tau aggregation reveals that the same regions of Tau are involved in both processes. TP4 inhibits Tau aggregation at substoichiometric concentration, demonstrating that it interferes with aggregation nucleation. This study provides residue-level insight into the interaction of Tau with an aggregation inhibitor and highlights the structural flexibility of Tau. PMID:24966331

  13. Summary of the Phase II, Title I engineering assessment of inactive uranium mill tailings, Phillips/United Nuclear Site, Ambrosia Lake, New Mexico

    International Nuclear Information System (INIS)

    1977-12-01

    An engineering assessment was performed of the problems resulting from the existence of radioactive uranium mill tailings at the Phillips/United Nuclear site at Ambrosia Lake, New Mexico. Services included the preparation of topographic maps, the performance of core drillings sufficient to determine areas and volumes of tailings and radiometric measurements to determine radium-contaminated materials, the evaluation of resulting radiation exposures of individuals and nearby populations, the investigation of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas release from the 2.6 million tons of tailings at the Phillips/United Nuclear site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation are also factors. The estimated radiological health effects to the general population are considered to be minimal. The two alternative actions presented are: dike stabilization, fencing, and maintenance; and adding 2 ft of stabilization cover material. Both options include remedial action at off-site structures and on-site decontamination around the tailings pile. Cost estimates for the two options are $920,000 and $2,230,000, respectively

  14. The effect of cojugate energy consumptions on comparative efficiency of alternatives of the development of nuclear power engineering

    International Nuclear Information System (INIS)

    Bubnov, V.P.; Bykov, A.I.; Egorushkin, S.V.

    1987-01-01

    The effect of control of conjugate energy consumptions on comparative efficiency of alternatives of the development of nuclear power engineering, including NPPs with thermal and fast reactors has been calculated. Economical-mathematical models of the system of nuclear power engineering including the subsystems of fuel utilization, fuel supply and conjugate industries, have been used. It has been shown, that with allowance for conjugate energy consumptions, the economic characteristics of nuclear power engineering sharply degradate when it develops only on the basis of thermal reactors. Putting the fast reactors into the system of nuclear power engineering has an important effect on reduction of conjugate energy consumptions and favors the increase of the efficiency of the system functioning during the considered time interval (60 years). Positive effects from putting breeders into operation become appreciable only on the latest estimated time intervals

  15. Engineering Issue: Technology Alternatives for the Remediation of PCB Contaminated Soils and Sediments

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) Engineering Issue papers are a series of documents that summarize the available information on specific contaminates, selected treatment and site remediation technologies, and related issues. This Engineering Issue paper is intended...

  16. The Marine Engineers in Today’s MAGTF: Historical Perspective, Consequences and Alternatives

    Science.gov (United States)

    2013-04-15

    Inhibited Flexibility for Resource Leveling ...........................................................................17 Mission and Capability...21 Inhibited Flexibility for Resource Leveling ...ground combat element ( GCE ); an engineer support battalion (ESB) supports the logistics combat element (LCE); and engineer operations divisions

  17. Alternative approaches to reliability modeling of a multiple engineered barrier system

    International Nuclear Information System (INIS)

    Ananda, M.M.A.; Singh, A.K.

    1994-01-01

    The lifetime of the engineered barrier system used for containment of high-level radioactive waste will significantly impact the total performance of a geological repository facility. Currently two types of designs are under consideration for an engineered barrier system, single engineered barrier system and multiple engineered barrier system. Multiple engineered barrier system consists of several metal barriers and the waste form (cladding). Some recent work show that a significant improvement of performance can be achieved by utilizing multiple engineered barrier systems. Considering sequential failures for each barrier, we model the reliability of the multiple engineered barrier system. Weibull and exponential lifetime distributions are used through out the analysis. Furthermore, the number of failed engineered barrier systems in a repository at a given time is modeled using a poisson approximation

  18. English title

    Directory of Open Access Journals (Sweden)

    Guillermo Alberto Tricoci

    2015-11-01

    Full Text Available Similarly to what happened with the steam engine, the electricity or the combustion engine, the new general-purpose technologies and ICTs have introduced many fundamental changes to our life and the processes we deal with daily. They have provided many benefits but have also produced unwanted collateral effects that should be considered. The first effect, at the beginning there was a new phenomenon known as the digital divide. Later on the uncertainty around the true scope of computing increased and evidence of a decrease in the capability of creating new jobs and stagnant or falling wages became clearer. All these, amongst other things, are considered part of the ICT revolution. The paradigm of continuous improvement to innovation and productivity begins to show the effects it produces in the disappearance and transformation of business roles. Many activities have disappeared and much of the business processes have received a very high degree of automation. These changes can be seen in the most varied fields.

  19. An Alternative Perspective for Malaysian Engineering Education: A Review from Year 2000-2012

    Science.gov (United States)

    Jayarajah, Kamaleswaran; Saat, Rohaida Mohd; Rauf, Rose Amnah Abdul

    2013-01-01

    The purpose of this study is to explore the research base of engineering education in the "Journal of Engineering Education" ("JEE") through an analysis review of articles for a 12-year period, from 2000 to 2012. The research base review focuses on identifying five characteristics of engineering education: (a) temporal…

  20. Combustion Characterization and Ignition Delay Modeling of Low- and High-Cetane Alternative Diesel Fuels in a Marine Diesel Engine

    OpenAIRE

    Petersen, John; Seivwright, Doug; Caton, Patrick; Millsaps, Knox

    2014-01-01

    The article of record as published may be found at http://dx.doi.org/10.1021/ef500565t In support of an ongoing U.S. Navy alternative fuel evaluation program, the combustion characteristics of two very different alternative diesel fuels were evaluated in a direct-injection marine diesel engine across a variety of speeds and loads. The fuels were an algal-based hydrotreated renewable diesel fuel (HRD) with cetane number of ∼75 and a synthetic paraffinic kerosene (SPK) with cetane n...

  1. Drug‑Drug and Drug‑Nutraceutical Cocrystal/Salt as Alternative Medicine for Combination Therapy: A Crystal Engineering Approach

    OpenAIRE

    Ranjit Thakuria; Bipul Sarma

    2018-01-01

    The pre-formulation of pharmaceutical cocrystals and salts is a concept of crystal engineering that has emerged as a promising technique for drug development in pharmaceutical industry. Recent introduction of pharmaceutical cocrystals in regulatory guidelines of US Food and Drug Administration (FDA) made them one of the potential alternatives when salt preparation is not feasible. Apart from generally regarded as safe (GRAS) coformers, drug‑drug and drug‑nutraceutical cocrystals are recent ad...

  2. Preliminary engineering assessment of treatment alternatives for groundwater from the Hanford 200 Area 200-BP-5 plumes

    International Nuclear Information System (INIS)

    1996-05-01

    This report presents the results of the Preliminary Engineering Assessment of Treatment Alternatives (PEATA), an engineering evaluation of potential treatment alternatives for groundwater extracted from the 200-BP-5 Area's 216-BY Cribs and 216-B-5 Reverse Well plumes. The primary objective of the PEATA was to identify treatment technologies that are worth further consideration (i.e., treatability testing or a more refined engineering evaluation). It will also provide a basis for evaluating the results of the treatability testing that is currently being conducted on the presumptive remedy of ion exchange with disposal of spent resin and will serve as a guide for selection of other technologies for additional testing. Because there are little data or past experience with groundwater similar to the BY-Crib and B-5 Reverse Well Plumes, treatment efficiencies cannot be predicted with certainty and rigorous treatment system designs and costs cannot be developed. This applies to all alternatives, including the presumptive remedy of ion exchange. The approach for this study was to develop conceptual designs and approximate costs for the treatment technologies that were most likely to be effective on the BY-Crib and B-5 Reverse Well groundwater

  3. Impact of Alternative Jet Fuels on Engine Exhaust Composition During the 2015 ECLIF Ground-Based Measurements Campaign.

    Science.gov (United States)

    Schripp, Tobias; Anderson, Bruce; Crosbie, Ewan C; Moore, Richard H; Herrmann, Friederike; Oßwald, Patrick; Wahl, Claus; Kapernaum, Manfred; Köhler, Markus; Le Clercq, Patrick; Rauch, Bastian; Eichler, Philipp; Mikoviny, Tomas; Wisthaler, Armin

    2018-04-17

    The application of fuels from renewable sources ("alternative fuels") in aviation is important for the reduction of anthropogenic carbon dioxide emissions, but may also attribute to reduced release of particles from jet engines. The present experiment describes ground-based measurements in the framework of the ECLIF (Emission and Climate Impact of Alternative Fuels) campaign using an Airbus A320 (V2527-A5 engines) burning six fuels of chemically different composition. Two reference Jet A-1 with slightly different chemical parameters were applied and further used in combination with a Fischer-Tropsch synthetic paraffinic kerosene (FT-SPK) to prepare three semi synthetic jet fuels (SSJF) of different aromatic content. In addition, one commercially available fully synthetic jet fuel (FSJF) featured the lowest aromatic content of the fuel selection. Neither the release of nitrogen oxide or carbon monoxide was significantly affected by the different fuel composition. The measured particle emission indices showed a reduction up to 50% (number) and 70% (mass) for two alternative jet fuels (FSJF, SSJF2) at low power settings in comparison to the reference fuels. The reduction is less pronounced at higher operating conditions but the release of particle number and particle mass is still significantly lower for the alternative fuels than for both reference fuels. The observed correlation between emitted particle mass and fuel aromatics is not strict. Here, the H/C ratio is a better indicator for soot emission.

  4. Preliminary study of used cooking oil methyl ester as an alternative fuel for diesel engine

    International Nuclear Information System (INIS)

    Roseli, A.; El-Awad, M.M.; Yusoff, M.Z.

    2006-01-01

    An experimental work has been carried out to compare the power performance and exhaust emissions of UCOME with OD on unmodified direct injection, four stroke single cylinder and stationary Robin diesel engine. Used cooking oil was transesterified by using methanol that yields immiscible fraction of glycerol and methyl ester (biodiesel). UCOME was separated by gravity before conducting further testing on its physical, chemical and thermal properties in the laboratory. For fuel power performance analysis, fuel consumption, gross energy input, torque, brake power, BMEP and SFC of the engine were measured and calculated. The analysis showed that at high engine speeds, the engine performances with UCOME are comparable to that of OD. However, UCOME increases specific fuel consumption due to its high specific density. In term of exhaust emissions UCOME showed a net reduction in exhaust emissions of NO x as compared with those of OD. This study has given optimistic information to pave the direction for further research on diesel engine

  5. Book of abstracts Chemical Engineering: IV All-Russian Conference on chemical engineering, All-Russian Youth Conference on chemical engineering, All-Russian school on chemical engineering for young scientists and specialists. Organic substances and pharmaceuticals engineering. Petrochemistry and chemical processing of alternative feedstock

    International Nuclear Information System (INIS)

    Zakhodyaeva, Yu.A.; Belova, V.V.

    2012-01-01

    In the given volume of abstracts of the IV All-Russian Conference on chemical engineering, All-Russian Youth Conference on chemical engineering, All-Russian school on chemical engineering for young scientists and specialists (Moscow, March 18-23, 2012) there are the abstracts of the reports concerning organic substances and pharmaceuticals engineering, petrochemistry and chemical processing of alternative feedstock. The abstracts deal with state-of-the-art and future development of theoretical and experimental investigations as well as with experience in practical realization of development works in the field of chemical engineering and relative areas [ru

  6. Characterization of Lean Misfire Limits of Mixture Alternative Gaseous Fuels Used for Spark Ignition Engines

    Directory of Open Access Journals (Sweden)

    Miqdam Tariq Chaichan

    2012-03-01

    Full Text Available Increasing on gaseous fuels as clean, economical and abundant fuels encourages the search for optimum conditions of gas-fueled internal combustion engines. This paper presents the experimental results on the lean operational limits of Recardo E6 engine using gasoline, LPG, NG and hydrogen as fuels. The first appearance of almost motoring cycle was used to define the engine lean limit after the fuel flow was reduced gradually. The effects of compression ratio, engine speed and spark timing on the engine operational limits are presented and discussed in detailed. Increasing compression ratio (CR extend the lean limits, this appears obviously with hydrogen, which has a wide range of equivalence ratios, while for hydrocarbon fuel octane number affect gasoline, so it can' t work above CR=9:1, and for LPG it reaches CR=12:1, NG reaches CR=15:1 at lean limit operation. Movement from low speeds to medium speeds extended lean misfire limits, while moving from medium to high speeds contracted the lean misfiring limits. NOx, CO and UBHC concentrations increased with CR increase for all fuels, while CO2 concentrations reduced with this increment. NOx concentration increased for medium speeds and reduced for high speeds, but the resulted concentrations were inconcedrable for these lean limits. CO and CO2 increased with engine speed increase, while UBHC reduced with this increment. The hydrogen engine runs with zero CO, CO2 and UNHC concentrations, and altra low levels of NOx concentrations at studied lean misfire limits

  7. Synthetic biology and its alternatives. Descartes, Kant and the idea of engineering biological machines.

    Science.gov (United States)

    Kogge, Werner; Richter, Michael

    2013-06-01

    The engineering-based approach of synthetic biology is characterized by an assumption that 'engineering by design' enables the construction of 'living machines'. These 'machines', as biological machines, are expected to display certain properties of life, such as adapting to changing environments and acting in a situated way. This paper proposes that a tension exists between the expectations placed on biological artefacts and the notion of producing such systems by means of engineering; this tension makes it seem implausible that biological systems, especially those with properties characteristic of living beings, can in fact be produced using the specific methods of engineering. We do not claim that engineering techniques have nothing to contribute to the biotechnological construction of biological artefacts. However, drawing on Descartes's and Kant's thinking on the relationship between the organism and the machine, we show that it is considerably more plausible to assume that distinctively biological artefacts emerge within a paradigm different from the paradigm of the Cartesian machine that underlies the engineering approach. We close by calling for increased attention to be paid to approaches within molecular biology and chemistry that rest on conceptions different from those of synthetic biology's engineering paradigm. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. A numerical investigation on the influence of EGR in a supercharged SI engine fueled with gasoline and alternative fuels

    International Nuclear Information System (INIS)

    Mardi K, Mohsen; Khalilarya, Shahram; Nemati, Arash

    2014-01-01

    Highlights: • CFD modeling the combustion of different alternative fuels in SI engine. • 10% of EGR is the most desirable amount from the viewpoint of emissions and power. • EGR affects on methane fuel more than others. • Supercharging has the most noticeable effect on gasoline fuel and the least on hydrogen fuel. - Abstract: Alternative fuels are mostly extracted from renewable resources, and their emission levels can be lower than those of traditional fossil-based fuels. A computational fluid dynamics (CFD) method is utilized to investigate the effects of exhaust gas recirculation (EGR) and initial charge pressure on the emissions and performance of a SI engine. The engine is fueled separately by gasoline and some of potential alternative fuels including hydrogen, propane, methane, ethanol and methanol. The results of simulation are compared to the experimental data. In all validation cases, experimental and numerical results were observed to have good agreement with each other. The calculations are carried out for EGR ratios between 0% and 20% and four cases of initial pressure have been mentioned: P in = 1, 1.2, 1.4, 1.6 bar. The effect of EGR on NO x emission of methane is more than other fuels and its effect on IMEP of hydrogen is less than other fuels. From the viewpoints of emission and power, 10% of EGR seems to be the most desirable amount. The most noticeable effect of supercharging is on gasoline unlike hydrogen, which seems to be affected the least. The comparison of results shows that hydrogen due to its high heating value and burning without producing any carbon-based compounds such as HC, CO and CO 2 is an ideal alternative fuel compared to the other fuels

  9. Final Report: Utilizing Alternative Fuel Ignition Properties to Improve SI and CI Engine Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Wooldridge, Margaret; Boehman, Andre; Lavoie, George; Fatouraie, Mohammad

    2017-11-30

    Experimental and modeling studies were completed to explore leveraging physical and chemical fuel properties for improved thermal efficiency of internal combustion engines. Fundamental studies of the ignition chemistry of ethanol and iso-octane blends and constant volume spray chamber studies of gasoline and diesel sprays supported the core research effort which used several reciprocating engine platforms. Single cylinder spark ignition (SI) engine studies were carried out to characterize the impact of ethanol/gasoline, syngas (H2 and CO)/gasoline and other oxygenate/gasoline blends on engine performance. The results of the single-cylinder engine experiments and other data from the literature were used to train a GT Power model and to develop a knock criteria based on reaction chemistry. The models were used to interpret the experimental results and project future performance. Studies were also carried out using a state of the art, direct injection (DI) turbocharged multi- cylinder engine with piezo-actuated fuel injectors to demonstrate the promising spray and spark timing strategies from single-cylinder engine studies on the multi-cylinder engine. Key outcomes and conclusions of the studies were: 1. Efficiency benefits of ethanol and gasoline fuel blends were consistent and substantial (e.g. 5-8% absolute improvement in gross indicated thermal efficiency (GITE)). 2. The best ethanol/gasoline blend (based on maximum thermal efficiency) was determined by the engine hardware and limits based on component protection (e.g. peak in-cylinder pressure or maximum turbocharger inlet temperature) – and not by knock limits. Blends with <50% ethanol delivered significant thermal efficiency gains with conventional SI hardware while maintain good safety integrity to the engine hardware. 3. Other compositions of fuel blends including syngas (H2 and CO) and other dilution strategies provided significant efficiency gains as well (e.g. 5% absolute improvement in ITE). 4. When the

  10. Alternative fuel produced from thermal pyrolysis of waste tires and its use in a DI diesel engine

    International Nuclear Information System (INIS)

    Wang, Wei-Cheng; Bai, Chi-Jeng; Lin, Chi-Tung; Prakash, Samay

    2016-01-01

    Highlights: • The liquid, solid and gas yields from pyrolysis of waste tires were investigated. • For energy and economic consideration, pre-treatments of TPO were avoided. • Various proportions of TPO-diesel mixture were tested in a DI diesel engine. • TPOs derived from various pyrolysis temperatures were also tested in engine. • Fuel consumption, cylinder pressure, engine power, and SO2 emission were discussed. - Abstract: Alternative fuels from waste material have been receiving attentions due to the increasing demand of fossil fuels. Pyrolysis has been a considerable solution for processing waste tires because it gives clean emissions and produces valuable liquid or solid products. Pyrolysis oil from waste tires has become a potential replacement for petroleum diesel due to the similar physical and chemical properties to diesel fuel. In this study, waste tires were pyrolyzed in a lab-scale fixed bed reactor with various reaction temperatures. The liquid, solid and gas product yields from different pyrolysis temperatures were compared, as well as the analyses of property and element for the oil product. Due to the energy and economic consideration, the pre-treatments of TPO before adding into regular diesel were avoided. The TPO derived from various pyrolysis temperatures were mixed with regular diesel at different proportions and subsequently tested in a DI diesel engine. The engine performance, such as fuel consumption, cylinder pressure, engine power, and SO_2 emission, were examined and discussed. The results indicated that increasing the TPO fraction in diesel lead to worse engine performance, but it can be recovered using TPOs produced from higher pyrolysis temperatures.

  11. Characteristics of Waste Plastics Pyrolytic Oil and Its Applications as Alternative Fuel on Four Cylinder Diesel Engines

    Directory of Open Access Journals (Sweden)

    Nosal Nugroho Pratama

    2014-02-01

    Full Text Available Waste plastics recycling using pyrolysis method is not only able to decrease a number of environment pollutant but also able to produce economical and high quality hydrocarbon products. Two experiments were conducted to completely study Waste Plastic Pyrolytic Oil (WPPO characteristics and its applications.  First experiment investigated oil characteristics derived from pyrolysis process in two stages batch reactors: pyrolysis and catalytic reforming reactor, at maximum temperature 500oC and 450oC respectively. Waste Polyethylene (PE, Polypropylene (PP, Polystyrene (PS, Polyethylene Terepthalate (PET and others were used as raw material. Nitrogen flow rate at 0.8 l/minutes was used to increase oil weight percentage. Indonesian natural zeolite was used as catalyst. Then, second experiment was carried out on Diesel Engine Test Bed (DETB used blending of WPPO and Biodiesel fuel with a volume ratio of 1:9. This experiment was specifically conducted to study how much potency of blending of WPPO and biodiesel in diesel engine. The result of first experiment showed that the highest weight percentage of WPPO derived from mixture of PE waste (50%wt, PP waste (40%wt and PS waste (10%wt is 45.13%wt. The more weight percentage of PE in feedstock effected on the less weight percentage of WPPO, the more percentage of C12-C20 content in WPPO and the higher calorific value of WPPO. Characteristics of WPPO such as, Specific Gravity, Flash point, Pour Point, Kinematic Viscosity, Calorific value and percentage of C12-C20 showed interesting result that WPPO could be developed as alternative fuel on diesel fuel blending due to the proximity of their characteristics. Performance of diesel engine using blending of WPPO and biodiesel on second experiment gave good result so the WPPO will have great potency to be valuable alternative liquid fuel in future, especially on stationary diesel engine and transportation engine application.

  12. Alternative approach to automated management of load flow in engineering networks considering functional reliability

    Directory of Open Access Journals (Sweden)

    Ирина Александровна Гавриленко

    2016-02-01

    Full Text Available The approach to automated management of load flow in engineering networks considering functional reliability was proposed in the article. The improvement of the concept of operational and strategic management of load flow in engineering networks was considered. The verbal statement of the problem for thesis research is defined, namely, the problem of development of information technology for exact calculation of the functional reliability of the network, or the risk of short delivery of purpose-oriented product for consumers

  13. 14 CFR 121.197 - Airplanes: Turbine engine powered: Landing limitations: Alternate airports.

    Science.gov (United States)

    2010-01-01

    ... obstruction clearance plane and the runway. In the case of an alternate airport for departure, as provided in § 121.617, allowance may be made for fuel jettisoning in addition to normal consumption of fuel and oil...

  14. Power supply for pumping systems in northern Chile: Photovoltaics as alternative to grid extension and diesel engines

    International Nuclear Information System (INIS)

    Chueco-Fernandez, Francisco J.; Bayod-Rujula, Angel A.

    2010-01-01

    This paper examines and compares the cost-effectiveness to energize pumping systems in remote areas on northern Chile by means of photovoltaic systems, diesel engines and grid extension. Variables such as the distance to the power grid, the voltage grid, the prices of electricity and fuel, and the required investments, are taken into account. The comparison is made for wide range of variable values, distances and pumping requirements. The results obtained are useful for choosing the best alternative for the power supply of pumping systems in wells in Northern Chile. (author)

  15. Detailed design, fabrication and testing of an engineering prototype compensated pulsed alternator. Final report

    International Nuclear Information System (INIS)

    Bird, W.L. Jr.; Woodson, H.H.

    1980-03-01

    The design, fabrication, and test results of a prototype compensated pulsed alternator are discussed. The prototype compulsator is a vertical shaft single phase alternator with a rotating armature and salient pole stator. The machine is designed for low rep rate pulsed duty and is sized to drive a modified 10 cm Beta amplifier. The load consists of sixteen 15 mm x 20 mm x 112 cm long xenon flashlamps connected in parallel. The prototype compulsator generates an open circuit voltage of 6 kV, 180 Hz, at a maximum design speed of 5400 rpm. At maximum speed, the inertial energy stored in the compulsator rotor is 3.4 megajoules

  16. Browse Title Index

    African Journals Online (AJOL)

    2004): Special Issue 2004, Differential production of immune parameters by mouse strains ... agglutination and complement fixation tests in the field diagnosis ... List All Titles · Free To Read Titles This Journal is Open Access.

  17. Mathematical Modelling in Engineering: An Alternative Way to Teach Linear Algebra

    Science.gov (United States)

    Domínguez-García, S.; García-Planas, M. I.; Taberna, J.

    2016-01-01

    Technological advances require that basic science courses for engineering, including Linear Algebra, emphasize the development of mathematical strengths associated with modelling and interpretation of results, which are not limited only to calculus abilities. Based on this consideration, we have proposed a project-based learning, giving a dynamic…

  18. Alternative Assessment in Engineering Language Education: The Case of the Technical University of Madrid

    Science.gov (United States)

    Pierce, Joana; Duran, Pilar; Ubeda, Paloma

    2011-01-01

    Engineering institutions across Europe are currently involved in a major process of reform and restructuring as a part of the Bologna Process, which stresses the role of competencies and outcomes in curriculum design. In the field of languages, the Council of Europe has developed the CEFR (Common European Framework of References) for languages,…

  19. INFLUENCE OF PALM METHYL ESTER (PME AS AN ALTERNATIVE FUEL IN MULTICYLINDER DIESEL ENGINE

    Directory of Open Access Journals (Sweden)

    Mohd Hafizil M. Yasin

    2012-12-01

    Full Text Available Palm oil is one of the vegetable oil, which is converted to biodiesel through a transesterification process using methanol as the catalyst. Palm oil biodiesel or palm methyl ester (PME can be used in diesel engines without any modification, and can be blended with conventional diesel to produce different proportions of PME-diesel blend fuels. The physical properties of PME were evaluated experimentally and theoretically. The effect of using neat PME as fuel on engine performance and emissions was evaluated using a commercial four-cylinder four-stroke IDI diesel engine. The experimental results on an engine operated with PME exhibited higher brake specific fuel consumption in comparison with the conventional fuel. With respect to the in-cylinder pressure and heat release rate, these increased features by over 8.11% and 9.3% with PME compared to conventional diesel. The overall results show that PME surpassed the diesel combustion quality due to its psychochemical properties and higher oxygen content.

  20. Fiat Chrysler Application for Alternative Methodology for Off-Cycle Technology Credits: Engine and Transmission Warmup

    Science.gov (United States)

    FCA Group LLC request to the EPA regarding greenhouse gas, off-cycle CO2 credits for Active Engine Warm Up used in 2011-2013 model year vehicles and Active Transmission Warm Up Technologies used in 2013 model year vehicles.

  1. PERFORMANCE AND EMISSION CHARACTERISTICS OF A CI ENGINE OPERATED ON VEGETABLE OILS AS ALTERNATIVE FUELS

    Directory of Open Access Journals (Sweden)

    K. Rajagopal

    2011-12-01

    Full Text Available An experimental analysis was done using a four-stroke, single cylinder, constant speed, water-cooled diesel engine, which was interfaced with Engine software. Performance and emission characteristics were evaluated for three non-edible vegetable oils, i.e. thumba, jojoba, neem oil, as well as jojoba methyl ester, to study the effect of injection pressure at 205, 220, 240 and 260 bar with a variation in injection timing at 23°bTDC and 28°bTDC. The performance of jojoba methyl ester improved with an increase in injection pressure. A maximum brake thermal efficiency of 29.72% was obtained with lower emissions compared to the other vegetable oils; this might be explained by low viscosity and better combustion. Further investigations were carried out with a new lubricant, SAE 5W-30, which improved the performance of the CI engine by 1.59%. All of the abovementioned investigations were fruitful and these results are expected to lead to substantial contributions in the development of a viable vegetable oil engine.

  2. Eucalyptus biodiesel as an alternative to diesel fuel: preparation and tests on DI diesel engine.

    Science.gov (United States)

    Tarabet, Lyes; Loubar, Khaled; Lounici, Mohand Said; Hanchi, Samir; Tazerout, Mohand

    2012-01-01

    Nowadays, the increasing oil consumption throughout the world induces crucial economical, security, and environmental problems. As a result, intensive researches are undertaken to find appropriate substitution to fossil fuels. In view of the large amount of eucalyptus trees present in arid areas, we focus in this study on the investigation of using eucalyptus biodiesel as fuel in diesel engine. Eucalyptus oil is converted by transesterification into biodiesel. Eucalyptus biodiesel characterization shows that the physicochemical properties are comparable to those of diesel fuel. In the second phase, a single cylinder air-cooled, DI diesel engine was used to test neat eucalyptus biodiesel and its blends with diesel fuel in various ratios (75, 50, and 25 by v%) at several engine loads. The engine combustion parameters such as peak pressure, rate of pressure rise, and heat release rate are determined. Performances and exhaust emissions are also evaluated at all operating conditions. Results show that neat eucalyptus biodiesel and its blends present significant improvements of carbon monoxide, unburned hydrocarbon, and particulates emissions especially at high loads with equivalent performances to those of diesel fuel. However, the NOx emissions are slightly increased when the biodiesel content is increased in the blend.

  3. Title IX Resource Guide

    Science.gov (United States)

    Office for Civil Rights, US Department of Education, 2015

    2015-01-01

    Title IX of the Education Amendments of 1972 (Title IX) prohibits discrimination based on sex in education programs and activities in federally funded schools at all levels. If any part of a school district or college receives any Federal funds for any purpose, all of the operations of the district or college are covered by Title IX. The essence…

  4. Free-piston Stirling engine/linear alternator 1000-hour endurance test

    Science.gov (United States)

    Rauch, J.; Dochat, G.

    1985-01-01

    The Free Piston Stirling Engine (FPSE) has the potential to be a long lived, highly reliable, power conversion device attractive for many product applications such as space, residential or remote site power. The purpose of endurance testing the FPSE was to demonstrate its potential for long life. The endurance program was directed at obtaining 1000 operational hours under various test conditions: low power, full stroke, duty cycle and stop/start. Critical performance parameters were measured to note any change and/or trend. Inspections were conducted to measure and compare critical seal/bearing clearances. The engine performed well throughout the program, completing more than 1100 hours. Hardware inspection, including the critical clearances, showed no significant change in hardware or clearance dimensions. The performance parameters did not exhibit any increasing or decreasing trends. The test program confirms the potential for long life FPSE applications.

  5. Performance evaluation of alternative fuel/engine concepts 1990- 1995. Final report including addendum of diesel vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Nylund, N.O.; Ikonen, M.; Kytoe, M.; Lappi, M.; Westerholm, M.; Laurikko, J. [VTT Energy, Espoo (Finland). Energy Use

    1996-12-31

    Annex V within the IEA Agreement on Alternative Motor Fuels is the first subtask to generate new experimental data. The objective of the task is to generate information on the emission potential of alternative fuels in severe operating conditions and to evaluate new emission measurement methods. The work was carried out in three phases, Engine Tests, Vehicle Tests and Addendum of Diesel Vehicles. The work was carried out at VTT (Technical Research Centre of Finland) as a cost shared operation. Participants were Belgium (Parts Two and Three), Canada (Parts One and Two), Finland, Italy (Part One), Japan, the Netherlands Sweden and USA. The United Kingdom also joined at the end of the Annex. The work included 143 different vehicle/fuel/temperature combinations. FTP type emission tests were run on 14 vehicles powered with different gasoline compositions, methanol (M50 and M85), ethanol (E85), LPG, CNG and diesel. Both regulated and unregulated emission components were measured using the most up-to-date emissions measurement technology. The results indicated, that today`s advanced gasoline vehicles must be considered rather clean. Diesel is comparable with gasoline in the case of CO and HC. M85 gives low emissions in warm conditions, but unburned methanol must be controlled. Natural gas and LPG are inherently clean fuels which, using up-to-date engine technology, give low emissions in all conditions. (orig.) (29 refs.)

  6. Hydrogen-ethanol blending as an alternative fuel of spark ignition engines

    Energy Technology Data Exchange (ETDEWEB)

    Al-Baghdadi, M.A.S. [University of Babylon (Iraq). Dept. of Mechanical Engineering

    2003-07-01

    The performance and pollutant emission of a four-stroke spark ignition engine using hydrogen-ethanol blends as fuel have been studied. The tests were performed using 2, 4, 6, 8, 1 0 and 12 mass% hydrogen-ethanol blends. Gasoline fuel was used as a basis for comparison. The effect of using different blends of hydrogen-ethanol on engine power, specific fuel consumption, CO and NO{sub x} emission was studied. Operating test results for a range of compression ratio (CR) and equivalent ratio are presented. The results show that the supplemental hydrogen in the ethanol-air mixture improves the combustion process and hence improves the combustion efficiency, expands the range of combustibility of the ethanol fuel, increases the power, reduces the s.f.c. and reduces toxic emissions. The important improvement of hydrogen addition is to reduce the s.f.c. of ethanol engines. Results were compared to those with gasoline fuel at 7 CR and stoichiometric equivalence ratio. (author)

  7. Engineering study: disposition of terminal liquors for interim storage. [Eight alternative processes

    Energy Technology Data Exchange (ETDEWEB)

    Metz, W.P.; Ogren, W.E.

    1975-02-01

    Eight alternative processes were chosen as being technologically feasible within the time frame dictated by budgeting procedures and terminal liquor availability. Solidified waste products acceptable for single-shell tank storage were assumed to be placed in available single-shell tanks. Double-shell tanks were used only for the more mobile terminal liquors or semi-solid mush products. The mush, chemical neutralization, and clay in-tank processes offer potential savings of tens of millions of dollars over double-shell tank storage of terminal liquors. In order to achieve this cost savings, the process development and demonstration must be completed prior to the beginning of double-shell tank construction (Dec. 1976) expected to be funded from a fiscal year 1977 line item. Budgeting for these additional double-shell tanks must proceed since the processing options discussed here are not yet available and may not prove to be available at the required time. This study indicates the following topics for additional study: Process technology development to achieve interim storage of terminal liquor products receives the greatest emphasis as a means of reducing capital expenditures. Interim storage product criteria, waste inventory, and conversion to final form require definition to allow comparison of the alternatives for disposition of terminal liquors. The pseudotechnical nature of product acceptability criteria is important to the evaluation of the partial neutralization and aluminum removal alternatives. More accurate estimates of terminal liquor quantity and composition are required to give a sound technical basis for choosing the appropriate processing alternative. Retrieval and reprocessing operations may affect the comparisons presented by this study. (DLC)

  8. Value engineering study report on Lower East Fork Poplar Creek Project. Alternative No. 3

    International Nuclear Information System (INIS)

    1995-08-01

    The project under study is Alternative No. 3 as identified in the Feasibility Study dated August 1994. This alternative is identified as Excavation and Disposal of Commercial/DOE, Other, and Residential Remedial Unit Soil. The assumptions used for generating baseline costs are discussed in site associated costs. It is further described as follows: Soils with mercury concentrations greater than 200 ppM in the Commercial/DOE and Other Remedial Units and greater than 180 ppM in the Residential Remedial Unit [41,300m 3 (54,000yd 3 a volume equivalent to approximately 6,750 dump truck loads)] would be excavated and disposed of in an approved, lined landfill at Y-12 with leachate collection and possible pretreatment of the leachate before discharge. Because 0.6 ha (1.5 acres) of wetland would be destroyed, wetlands banking would occur, whereby a 1.8-ha (4.5-acre) wetland would be constructed on DOE-owned land near K-25. Borrow soil would be obtained from the Y-12 West End Borrow Area or from excess soil located at Y-12 landfills to fill the excavation. It is estimated that 7.3 ha (18.2 acres, and area about the size of 17 football fields) of habitat would be adversely affected. This alternative would use BMPs to minimize any adverse affects and to comply substantively with regulatory requirements

  9. Impact of alternative fuels on emissions characteristics of a gas turbine engine - part 2: volatile and semivolatile particulate matter emissions.

    Science.gov (United States)

    Williams, Paul I; Allan, James D; Lobo, Prem; Coe, Hugh; Christie, Simon; Wilson, Christopher; Hagen, Donald; Whitefield, Philip; Raper, David; Rye, Lucas

    2012-10-02

    The work characterizes the changes in volatile and semivolatile PM emissions from a gas turbine engine resulting from burning alternative fuels, specifically gas-to-liquid (GTL), coal-to-liquid (CTL), a blend of Jet A-1 and GTL, biodiesel, and diesel, to the standard Jet A-1. The data presented here, compares the mass spectral fingerprints of the different fuels as measured by the Aerodyne high resolution time-of-flight aerosol mass spectrometer. There were three sample points, two at the exhaust exit plane with dilution added at different locations and another probe located 10 m downstream. For emissions measured at the downstream probe when the engine was operating at high power, all fuels produced chemically similar organic PM, dominated by C(x)H(y) fragments, suggesting the presence of long chain alkanes. The second largest contribution came from C(x)H(y)O(z) fragments, possibly from carbonyls or alcohols. For the nondiesel fuels, the highest loadings of organic PM were from the downstream probe at high power. Conversely, the diesel based fuels produced more organic material at low power from one of the exit plane probes. Differences in the composition of the PM for certain fuels were observed as the engine power decreased to idle and the measurements were made closer to the exit plane.

  10. A COMPREHENSIVE STUDY OF DI DIESEL ENGINE PERFORMANCE WITHVEGETABLE OIL: AN ALTERNATIVE BIO-FUEL SOURCE OF ENERGY

    Directory of Open Access Journals (Sweden)

    A. K. Azad

    2012-06-01

    Full Text Available This study offers comprehensive details on the use of bio-fuel as a viable and alternative source of energy. The bio-fuel was prepared from vegetable oil, i.e., mustard oil and tested in a diesel engine in both pure form and as a diesel blend. The mustard oil blend proportions were 20%, 30%, 40% and 50% and named as bio-diesel blends B20, B30, B40 and B50. A fuel-testing laboratory determined the properties of the pure mustard oil fuel and its blends, i.e., density, viscosity, dynamic viscosity, carbon residue, flash point, fire point and calorific value. An assessment of engine performance, i.e., brake horsepower (bhp, brake specific fuel consumption (bsfc, brake thermal efficiency (bte and brake mean effective pressure (bmep etc., was carried out for pure diesel, pure mustard and the blends, both in laboratory conditions and under British Standard (BS conditions. Finally, an analysis and comparison was made of the effects of the various fuels on the different engine properties.

  11. The Role of Alternative Testing Strategies in Environmental Risk Assessment of Engineered Nanomaterials

    DEFF Research Database (Denmark)

    Hjorth, Rune; Holden, Patricia; Hansen, Steffen Foss

    2017-01-01

    ) workshop in Washington, D.C. and serves as the point of depature for this paper. Here we present the main outcomes by describing and defining the use of ATS for ENMs as well as discussing its future role in environmental risk science. We conclude that diversity in testing should be encouraged to avoid...... chemicals are challenged. Nonetheless, standardized whole organism animal testing is still considered the gold standard for environmental risk assessment. Advancing risk analysis of engineered nanomaterials (ENMs) through ATS was discussed in September 2014 at an international Society for Risk Analysis (SRA...... be utilized to skip uncertain environmental extrapolations and give rise to more accurate risk analysis....

  12. Tandem Mass Spectrum Sequencing: An Alternative to Database Search Engines in Shotgun Proteomics.

    Science.gov (United States)

    Muth, Thilo; Rapp, Erdmann; Berven, Frode S; Barsnes, Harald; Vaudel, Marc

    2016-01-01

    Protein identification via database searches has become the gold standard in mass spectrometry based shotgun proteomics. However, as the quality of tandem mass spectra improves, direct mass spectrum sequencing gains interest as a database-independent alternative. In this chapter, the general principle of this so-called de novo sequencing is introduced along with pitfalls and challenges of the technique. The main tools available are presented with a focus on user friendly open source software which can be directly applied in everyday proteomic workflows.

  13. Use of citric acid esters as alternative fuel for diesel engines

    Energy Technology Data Exchange (ETDEWEB)

    Huber, Georg; Thuneke, Klaus; Remmele, Edgar [Technologie- und Foerderzentrum, Straubing (Germany); Schieder, Doris [Technische Univ. Muenchen, Straubing (Germany). Lehrstuhl fuer Chemie Biogener Rohstoffe

    2013-06-01

    Common fuels for (adapted) diesel engines are fossil diesel fuel, fatty acid methyl ester (FAME or biodiesel) or vegetable oils. Furthermore the citric acid esters tributylcitrate (TBC) and triethylcitrate (TEC) are expected to be a possible diesel substitute. Their use as fuel was applied for a patent in Germany in 2010. According to the patent applicant the advantages are low soot combustion, independence of energy imports due to the possibility of local production and a broad raw material base. Their fuel properties have been analysed in the laboratory and compared with the relevant fuel standards. Only some of the determined values are meeting the specifications, but on the other hand few rapeseed oil characteristics (e. g. oxidation stability and viscosity) can be improved if the citric acid esters are used as a blend component. The operating and emission behaviour of a vegetable oil compatible CHP unit fuelled with various rapeseed oil and TBC blends were investigated and a trouble free and soot emission reduced engine operation due to the high molecularly bound oxygen content was observed. Long term test runs are necessary for an entire technical validation. (orig.)

  14. Ignition assist systems for direct-injected, diesel cycle, medium-duty alternative fuel engines: Final report phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Chan, A.K.

    2000-02-23

    This report is a summary of the results of Phase 1 of this contract. The objective was to evaluate the potential of assist technologies for direct-injected alternative fuel engines vs. glow plug ignition assist. The goal was to demonstrate the feasibility of an ignition system life of 10,000 hours and a system cost of less than 50% of the glow plug system, while meeting or exceeding the engine thermal efficiency obtained with the glow plug system. There were three tasks in Phase 1. Under Task 1, a comprehensive review of feasible ignition options for DING engines was completed. The most promising options are: (1) AC and the ''SmartFire'' spark, which are both long-duration, low-power (LDLP) spark systems; (2) the short-duration, high-power (SDHP) spark system; (3) the micropilot injection ignition; and (4) the stratified charge plasma ignition. Efforts concentrated on investigating the AC spark, SmartFire spark, and short-duration/high-power spark systems. Using proprietary pricing information, the authors predicted that the commercial costs for the AC spark, the short-duration/high-power spark and SmartFire spark systems will be comparable (if not less) to the glow plug system. Task 2 involved designing and performing bench tests to determine the criteria for the ignition system and the prototype spark plug for Task 3. The two most important design criteria are the high voltage output requirement of the ignition system and the minimum electrical insulation requirement for the spark plug. Under Task 3, all the necessary hardware for the one-cylinder engine test was designed. The hardware includes modified 3126 cylinder heads, specially designed prototype spark plugs, ignition system electronics, and parts for the system installation. Two 3126 cylinder heads and the SmartFire ignition system were procured, and testing will begin in Phase 2 of this subcontract.

  15. ALTERNATIVE AVIATION FUELS FOR USE IN MILITARY APUS AND ENGINES VERSATILE AFFORDABLE ADVANCED TURBINE ENGINE (VAATE), PHASE II AND III. Delivery Order 0007: Alternative Aviation Fuels for Use in Military Auxiliary Power Units (APUs) and Engines

    Science.gov (United States)

    2017-06-03

    85-180L(A) WC-130 Hercules 85-98 KC/ RC /WC-135 KC-135 Stratotanker 85-180L RC -135U Combat Sent JFS100-135 WC-135 Constant Phoenix 85-98CK C-17... plane . The control room houses the required equipment for processing, recording, and displaying analog and digital test data. 6 DISTRIBUTION...engine conditions and is designed to duplicate the 131-9[B] engine combustion system aerodynamics from the deswirl exit to the turbine stator inlet plane

  16. Analysis of alternative actions for import substitution policy implementation in machine engineering complex

    Directory of Open Access Journals (Sweden)

    Chevychelov Sergey

    2017-01-01

    Full Text Available This paper discusses the considerations for production modernization, replacement of imported spare parts manufactured in-house and redistribution of items manufactured spare parts between managed societies, with a goal to improve the quality and reliability of products, to reduce its cost, and work. Noted that the process of acquiring new foreign equipment and modern materials are complicated. There are examples of restrictive measures of the sanctions impact on industrial products and the dynamics of dependency on imports of industrial products. We used analytic and statistical research methods. Authors conducted a comparative analysis of the engineering assets of «Metalloinvest» holding that showed that all businesses have an impressive fleet of metal-working equipment on all groups of machines on the basis of an analysis of the needs for them to transport spare parts.

  17. Expanding beyond canonical metabolism: Interfacing alternative elements, synthetic biology, and metabolic engineering

    Directory of Open Access Journals (Sweden)

    Kevin B. Reed

    2018-03-01

    Full Text Available Metabolic engineering offers an exquisite capacity to produce new molecules in a renewable manner. However, most industrial applications have focused on only a small subset of elements from the periodic table, centered around carbon biochemistry. This review aims to illustrate the expanse of chemical elements that can currently (and potentially be integrated into useful products using cellular systems. Specifically, we describe recent advances in expanding the cellular scope to include the halogens, selenium and the metalloids, and a variety of metal incorporations. These examples range from small molecules, heteroatom-linked uncommon elements, and natural products to biomining and nanotechnology applications. Collectively, this review covers the promise of an expanded range of elemental incorporations and the future impacts it may have on biotechnology.

  18. Emulsification of waste cooking oils and fatty acid distillates as diesel engine fuels: An attractive alternative

    Directory of Open Access Journals (Sweden)

    Eliezer Ahmed Melo Espinosa

    2016-06-01

    Full Text Available The scope of this paper is to analyze the possibility and feasibility of the use of emulsification method applied to waste cooking oils and fatty acid distillates as diesel engine fuels, compared with other commonly used methods. These waste products are obtained from the refining oil industry, food industry and service sector, mainly. They are rarely used as feedstock to produce biofuels and other things, in spite of constitute a potential source of environmental contamination. From the review of the state of arts, significant decreases in exhaust emissions of nitrogen oxides, cylinder pressure as well as increases of the ignition delay, brake specific fuel consumption, hydrocarbon, smoke opacity, carbon monoxide, particulate matters to emulsified waste cooking oils and fatty acid distillates compared with diesel fuel are reported. In some experiments the emulsified waste cooking oils achieved better performance than neat fatty acid distillates, neat waste cooking oils and their derivatives methyl esters.

  19. Rosetta comparative modeling for library design: Engineering alternative inducer specificity in a transcription factor.

    Science.gov (United States)

    Jha, Ramesh K; Chakraborti, Subhendu; Kern, Theresa L; Fox, David T; Strauss, Charlie E M

    2015-07-01

    Structure-based rational mutagenesis for engineering protein functionality has been limited by the scarcity and difficulty of obtaining crystal structures of desired proteins. On the other hand, when high-throughput selection is possible, directed evolution-based approaches for gaining protein functionalities have been random and fortuitous with limited rationalization. We combine comparative modeling of dimer structures, ab initio loop reconstruction, and ligand docking to select positions for mutagenesis to create a library focused on the ligand-contacting residues. The rationally reduced library requirement enabled conservative control of the substitutions by oligonucleotide synthesis and bounding its size within practical transformation efficiencies (∼ 10(7) variants). This rational approach was successfully applied on an inducer-binding domain of an Acinetobacter transcription factor (TF), pobR, which shows high specificity for natural effector molecule, 4-hydroxy benzoate (4HB), but no native response to 3,4-dihydroxy benzoate (34DHB). Selection for mutants with high transcriptional induction by 34DHB was carried out at the single-cell level under flow cytometry (via green fluorescent protein expression under the control of pobR promoter). Critically, this selection protocol allows both selection for induction and rejection of constitutively active mutants. In addition to gain-of-function for 34DHB induction, the selected mutants also showed enhanced sensitivity and response for 4HB (native inducer) while no sensitivity was observed for a non-targeted but chemically similar molecule, 2-hydroxy benzoate (2HB). This is unique application of the Rosetta modeling protocols for library design to engineer a TF. Our approach extends applicability of the Rosetta redesign protocol into regimes without a priori precision structural information. © 2015 Wiley Periodicals, Inc.

  20. Engineering evaluation of alternatives: Managing the assumed leak from single-shell Tank 241-T-101

    International Nuclear Information System (INIS)

    Brevick, C.H.; Jenkins, C.

    1996-02-01

    At mid-year 1992, the liquid level gage for Tank 241-T-101 indicated that 6,000 to 9,000 gal had leaked. Because of the liquid level anomaly, Tank 241-T-101 was declared an assumed leaker on October 4, 1992. SSTs liquid level gages have been historically unreliable. False readings can occur because of instrument failures, floating salt cake, and salt encrustation. Gages frequently self-correct and tanks show no indication of leak. Tank levels cannot be visually inspected and verified because of high radiation fields. The gage in Tank 241-T-101 has largely corrected itself since the mid-year 1992 reading. Therefore, doubt exists that a leak has occurred, or that the magnitude of the leak poses any immediate environmental threat. While reluctance exists to use valuable DST space unnecessarily, there is a large safety and economic incentive to prevent or mitigate release of tank liquid waste into the surrounding environment. During the assessment of the significance of the Tank 241-T-101 liquid level gage readings, Washington State Department of Ecology determined that Westinghouse Hanford Company was not in compliance with regulatory requirements, and directed transfer of the Tank 241-T-101 liquid contents into a DST. Meanwhile, DOE directed WHC to examine reasonable alternatives/options for safe interim management of Tank 241-T-101 wastes before taking action. The five alternatives that could be used to manage waste from a leaking SST are: (1) No-Action, (2) In-Tank Stabilization, (3) External Tank Stabilization, (4) Liquid Retrieval, and (5) Total Retrieval. The findings of these examinations are reported in this study

  1. Dynamic analysis of Free-Piston Stirling Engine/Linear Alternator-load system-experimentally validated

    Science.gov (United States)

    Kankam, M. David; Rauch, Jeffrey S.; Santiago, Walter

    1992-01-01

    This paper discusses the effects of variations in system parameters on the dynamic behavior of the Free-Piston Stirling Engine/Linear Alternator (FPSE/LA)-load system. The mathematical formulations incorporate both the mechanical and thermodynamic properties of the FPSE, as well as the electrical equations of the connected load. A state-space technique in the frequency domain is applied to the resulting system of equations to facilitate the evaluation of parametric impacts on the system dynamic stability. Also included is a discussion on the system transient stability as affected by sudden changes in some key operating conditions. Some representative results are correlated with experimental data to verify the model and analytic formulation accuracies. Guidelines are given for ranges of the system parameters which will ensure an overall stable operation.

  2. Potential utilization of biodiesel as alternative fuel for compression ignition engine in Malaysia

    Science.gov (United States)

    Wahab, M. A.; Ma'arof, M. I. N.; Ahmad, I. N.; Husain, H.

    2017-10-01

    Biodiesel is a type of fuel which is derived from various sources of vegetable plants and waste fuels. Today, numerous biodiesels have been engineered to be at par or even better in term of performance in comparison to pure diesel. Therefore, biodiesel has shown a promising sign as one of the best candidate in overcoming total dependency on pure diesel. This paper gives review on various tests and experiments conducted on biodiesel in order to highlight the potentials given by this particular fuel. In addition, providing the supporting evidences to further endorse for a mass usage of biodiesel in Malaysia - simultaneously, driving the country to become a potential global biodiesel producer in the near future. The reviewed studies were obtained mainly via indexed journals and online libraries. Conclusively, every test and study for every blend of biodiesel had shown consistent positive results in regards to performance and in overcoming emission related issues. Thus, providing the evidence that biodiesel is highly reliable. Malaysia as a semi-agricultural nation could take the advantage in becoming one of the leading global biodiesel producers. Nevertheless, this will requires total cooperation of every concerned government bodies and authorities.

  3. STUDY OF ALTERNATIVE FUELS AND EFFECTS OF COMPRESSION RATIO ON THERMAL EFFICIENCY AND ENGINE POWER

    Directory of Open Access Journals (Sweden)

    Sarjito Sarjito

    2017-01-01

    Full Text Available This paper was a case study during the sabatical program at Kingston University London in February 2007. It has been studied by team of motorsport automotive department Kingston University London and it has been elaborated as a final project on Master Program. This study takes into account some of the issues surrounding the debate about alcohol fuels in Motorsport and the wider automotive sector and is primarily concerned to add data where there seems to be little existing research since Motorsport is a secretive business. Motorsport plays an important part in the automotive industry and is a sport enjoyed worldwide. Racing practice is regarded as using the best available resources and technology as it requires optimal performance. The racing arena gives engineers the opportunity to test valuable technological solutions to prove their merits. Therefore, racing is the natural starting point for introducing new technological solutions to the public and could lead to the wholesale conversion to renewable fuels to meet our automotive energy needs. Alcohol has unique properties that make superior in many ways to ordinary gasoline. The higher knock resistance allows for higher compression ratios to be utilized resulting in higher power outputs and thermal efficiency. The efficient use of energy is of growing concern in all spheres of life and the automotive sector needs to be front runner in these efforts.

  4. Engineering evaluation of alternatives: Technologies for monitoring interstitial liquids in single-shell tanks

    International Nuclear Information System (INIS)

    Brevick, C.H.; Jenkins, C.E.

    1996-02-01

    A global search of mature, emerging, and conceptual tank liquid monitoring technologies, along with a historical review of Hanford tank farm waste monitoring instrumentation, was conducted to identify methods for gauging the quantity of interstitial waste liquids contained in Hanford SSTs. Upon completion of the search, an initial screening of alternatives was conducted to identify candidates which might be capable of monitoring interstitial tank liquids. The nine candidate technologies that were selected, evaluated, and ranked are summarized. Hydrostatic tank gauging (HTG) is the technology generally recommended for gauging the quantity of process materials contained in Hanford SSTs. HTG is a mass-based technique that has the capability for continuous remote monitoring. HTG has the advantages of no moving parts, intrinsic safety, and potentially gauging a one-million gal tank with a precision of approximately ±500 pounds (i.e., ±62 gal of water or ±0.02 in. of level in a 75 ft diameter tank). HTG is relatively inexpensive and probe design, construction, testing, installation, and operation should be straightforward. HTG should be configured as part of a hybrid tank gauging system. A hybrid system employs two or more independent measurement systems which function in concert to provide redundancy, improved accuracy, and maximum information at minimum cost. An excellent hybrid system choice for monitoring interstitial liquids in SSTs might be the combination of HTG with thermal differential technology

  5. Supersonic plasma beams with controlled speed generated by the alternative low power hybrid ion engine (ALPHIE) for space propulsion

    Science.gov (United States)

    Conde, L.; Domenech-Garret, J. L.; Donoso, J. M.; Damba, J.; Tierno, S. P.; Alamillo-Gamboa, E.; Castillo, M. A.

    2017-12-01

    The characteristics of supersonic ion beams from the alternative low power hybrid ion engine (ALPHIE) are discussed. This simple concept of a DC powered plasma accelerator that only needs one electron source for both neutral gas ionization and ion beam neutralization is also examined. The plasma production and space charge neutralization processes are thus coupled in this plasma thruster that has a total DC power consumption of below 450 W, and uses xenon or argon gas as a propellant. The operation parameters of the plasma engine are studied in the laboratory in connection with the ion energy distribution function obtained with a retarding-field energy analyzer. The ALPHIE plasma beam expansion produces a mesothermal plasma flow with two-peaked ion energy distribution functions composed of low and high speed ion groups. The characteristic drift velocities of the fast ion groups, in the range 36.6-43.5 Km/s, are controlled by the acceleration voltage. These supersonic speeds are higher than the typical ion sound velocities of the low energy ion group produced by the expansion of the plasma jet. The temperatures of the slow ion population lead to ion Debye lengths longer than the electron Debye lengths. Furthermore, the electron impact ionization can coexist with collisional ionization by fast ions downstream the grids. Finally, the performance characteristics and comparisons with other plasma accelerator schemes are also discussed.

  6. Experimental Studies on Four Stroke Diesel Engine Fuelled with Tamarind Seed Oil as Potential Alternate Fuel for Sustainable Green Environment

    Directory of Open Access Journals (Sweden)

    V. Dhana Raju

    2018-01-01

    Full Text Available The main objective of this present novel work is to investigate the performance, combustion and emission characteristics of biodiesel derived from the tamarind seed through the transesterification process as potential alternative feedstock for the diesel engine. The physio-chemical properties of tamarind seed methyl ester (TSME were evaluated experimentally and compared with the base fuel. Test fuels were prepared in 3 concentrations such as B10 (10% tamarind seed oil and 90% diesel, B20 and B30.Experiments were conducted at a constant speed, the injection timing of 23° crank angle and compression ratio 17.5:1 with varying load conditions to investigate the diesel engine characteristics. TSME 20 shown better thermal efficiency (34.41% over diesel which is 1.17 % higher and also it produces lower emissions of CO, HC, and smoke opacity. N-Amyl alcohol (NAA is used as a fuel additive for the optimum blend of TSME20; added in 5% and 10% concentration on the volume basis. From the analysis of experimental data, the use of fuel additives significantly reduces the smoke opacity by 29.49 % for TSME20 NAA 10% blend in addition to the reduction of carbon monoxide and hydrocarbons emissions; however, the specific fuel consumption and the oxides of nitrogen were marginally increased.

  7. Ecological engineering alternatives for remediation and restoration of a drastically disturbed landscape

    Energy Technology Data Exchange (ETDEWEB)

    Nairn, R W; Hare, L; Mercer, M; Dresback, K; Pepple, K; Kirchner, A; Cseak, D; Lossing, J; Durham, C; Chen, B

    1999-07-01

    As part of a Fall 1998 Environmental Science graduate seminar in Ecological Engineering at the University of Oklahoma, students were asked to submit a proposal for the holistic and sustainable restoration of the Tar Creek Superfund Site, Ottawa county, Oklahoma. the Tar Creek site is a portion of an abandoned lead and zinc mining area known as the Tri-State Mining District (OL, KS and MO) and includes approximately 104 square kilometers of disturbed land surface and contaminated water resources in extreme northeastern Oklahoma. Approximately 94 million cubic meters of contaminated water currently exist in the underground voids. In 1979, acidic, metal-rich waters began to discharge into Tar Creek from natural springs, bore holes and mine shafts. In addition, approximately 37 million cubic meters of processed mine waste materials (chat) litter their surface in large piles. Approximately 324 hectares of contaminated tailings settling ponds also exist on site. Student submitted proposals addressed the following four subject areas: passive treatment options for stream water quality improvement, surface reclamation and revegetation, stream habitat restoration and joint ecological and economic sustainability. Proposed designs for passive treatment of the contaminated mine drainage included unique constructed wetland designs that relief on a combination of biological and geochemical processes, use of microbial mats for luxury metal uptake, enhanced iron oxidation via windmill-based aeration and fly ash injection. proposed surface reclamation methods included minimal regrading following by biosolid, ash and other organic amendment applications and several phytoremediation techniques, especially the use of hyperaccumulators. The stream and riparian restoration portion of the proposals focused on chat removal, phytoremediation and species reintroduction. proposed joint ecological and economic sustainability ventures included development of recreational facilities, mining

  8. Friction riveting as an alternative mechanical fastening to join engineering plastics

    Science.gov (United States)

    Gagliardi, Francesco; Conte, Romina; Bentrovato, Renato; Simeoli, Giorgio; Russo, Pietro; Ambrogio, Giuseppina

    2018-05-01

    Friction Rivecting is a quite new joining process to connect multi-material structures. In brief, a metallic rivet is dipped rotating inside matrixes, usually made of plastics, increasing its original diameter. The use of high-performance plastics is more suitable being their higher mechanical and thermal properties important to avoid material degradation and to allow strong part connections. High-speed friction welding system has been usually used to perform the process. In the work here proposed, the joints have been achieved by means of a traditional milling machine and the attention has been focused on a widely used engineering plastic, i.e. polyamide 6 (PA6) with and without glass fiber reinforcement. A specific speed multiplier has been attached into the mandrel of the used machine to increase the reachable rotational speed. Moreover, rivets made of Titanium Grade 2 and of an Aluminum Alloy, the AA-6060, are utilized. The influence that the heating and the forging length can have on the quality of the obtained junctions, considering a fixed joining depth, has been tested and investigated. The performed connections have been judged by tensile tests, which were set to quantify the maximum strength of the joints for a transverse speed of 1,0 mm/min. Barreling effect can be observed close to the tip, which loses the initial shape of a cylinder characterized by straight vertical walls. Finally, the possible degradation of the polymer, due to temperature increment, has been also evaluated close to the working zone. According to that, it has to be highlighted that the process needs a heating balance, which is necessary to get sound joints. The compromise has, on one side, to allow the rivet penetration and deformation, and on the other side, to avoid the degradation of the polymer, which would affect its properties and a proper rivet deformation.

  9. Effects of Alternate Leading Edge Cutback on the Space Shuttle Main Engine Low Pressure Fuel Pump

    Science.gov (United States)

    Mulder, Andrew; Skelley, Stephen

    2016-01-01

    A higher order cavitation oscillation observed in the SSME low pressure fuel pump has been eliminated in water flow testing of a modified subscale replica of the inducer. The low pressure pump was modified by removing the outboard sections of two opposing blades of the four-bladed inducer, blending the "cutback" regions into the blades at the leading edge and tip, and removing material on the suction sides to decrease the exposed leading edge thickness. The leading edge tips of the cutback blades were moved approximately 25 degrees from their previous locations, thereby increasing one blade to blade spacing, decreasing the second, while simultaneously moving the cutback tips downstream. The test was conducted in MSFC's inducer test loop at scaled operating conditions in degassed and filtered water. In addition to eliminating HOC across the entire scaled operating regime, rotating cavitation was suppressed while the range of both alternate blade and asymmetric cavitation were increased. These latter phenomena, and more significantly, the shifts between these cavitation modes also resulted in significant changes to the head coefficient at low cavitation numbers. Reverse flow was detected at a slightly larger flow coefficient with the cutback inducer and suction capability was reduced by approximately 1 velocity head at and above approximately 90% of the reference flow coefficient. These performance changes along with more intense reverse flow are consistent with poor flow area management and increased incidence in the cutback region. Although the test demonstrated that the inducer modification was successful at eliminating the higher order cavitation across the entire scaled operating regime, different, previously unobserved, cavitation oscillations were introduced and significant performance penalties were imposed.

  10. Micro/Nano Multilayered Scaffolds of PLGA and Collagen by Alternately Electrospinning for Bone Tissue Engineering

    Science.gov (United States)

    Kwak, Sanghwa; Haider, Adnan; Gupta, Kailash Chandra; Kim, Sukyoung; Kang, Inn-Kyu

    2016-07-01

    The dual extrusion electrospinning technique was used to fabricate multilayered 3D scaffolds by stacking microfibrous meshes of poly(lactic acid-co-glycolic acid) (PLGA) in alternate fashion to micro/nano mixed fibrous meshes of PLGA and collagen. To fabricate the multilayered scaffold, 35 wt% solution of PLGA in THF-DMF binary solvent (3:1) and 5 wt% solution of collagen in hexafluoroisopropanol (HFIP) with and without hydroxyapatite nanorods (nHA) were used. The dual and individual electrospinning of PLGA and collagen were carried out at flow rates of 1.0 and 0.5 mL/h, respectively, at an applied voltage of 20 kV. The density of collagen fibers in multilayered scaffolds has controlled the adhesion, proliferation, and osteogenic differentiation of MC3T3-E1 cells. The homogeneous dispersion of glutamic acid-modified hydroxyapatite nanorods (nHA-GA) in collagen solution has improved the osteogenic properties of fabricated multilayered scaffolds. The fabricated multilayered scaffolds were characterized using FT-IR, X-ray photoelectron spectroscopy, and transmission electron microscopy (TEM). The scanning electron microscopy (FE-SEM) was used to evaluate the adhesion and spreads of MC3T3-E1 cells on multilayered scaffolds. The activity of MC3T3-E1 cells on the multilayered scaffolds was evaluated by applying MTT, alkaline phosphatase, Alizarin Red, von Kossa, and cytoskeleton F-actin assaying protocols. The micro/nano fibrous PLGA-Col-HA scaffolds were found to be highly bioactive in comparison to pristine microfibrous PLGA and micro/nano mixed fibrous PLGA and Col scaffolds.

  11. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 229 ... Browse Title Index ... Issue, Title. Vol 14, No 2 ... Vol 15, No 1 (2017), Qualitative and quantitative methods of suicide research in old age, Abstract PDF ... Vol 11, No 2 (2013), Simple Algorithm in the Management of Fetal ...

  12. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 250 of 488 ... African Journal of Paediatric Surgery. ... Ileocecal valve atresia: Introduction of a new surgical approach ... Vol 4, No 1 (2007), Isolated Bilateral Macrostomia: Case Series and ... Vol 9, No 2 (2012), Laparoscopic inguinal hernia repair in ... List All Titles · Free To Read Titles This Journal is Open Access.

  13. Browse Title Index

    African Journals Online (AJOL)

    Items 601 - 650 of 788 ... Browse Title Index ... Issue, Title ... Vol 14, No 1 (2006), Social science research: a critique of quantitative and qualitative methods ... Vol 18, No 1 (2010), Stress among part-time business students: a study in a Ghanaian ...

  14. Title to mining properties

    International Nuclear Information System (INIS)

    Crouch, K.M.

    1976-01-01

    The requirements of the law which must be met in order to create title to an unpatented mining claim and the procedures which should be followed when an attempt is made to determine the title to the claim is acceptable are reviewed

  15. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXIV, I--MAINTAINING THE FUEL SYSTEM PART III--CATERPILLAR DIESEL ENGINE, II--UNDERSTANDING THE VOLTAGE REGULATOR/ALTERNATOR.

    Science.gov (United States)

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE FUEL AND BATTERY CHARGING SYSTEM. TOPICS ARE (1) INJECTION TIMING CONTROLS, (2) GOVERNOR, (3) FUEL SYSTEM MAINTENANCE TIPS, (4) THE CHARGING SYSTEM, (5) REGULATING THE GENERATOR/ALTERNATOR, AND (6) CHARGING SYSTEM SERVICE…

  16. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 194 ... Journal Home > Advanced Search > Browse Title Index ... Vol 14, No 1 (2000), A functional categoriality of adjectives in ... Vol 1, No 1 (1987), Alienation and affirmation: The humanistic vision of Bessie Head, Abstract PDF.

  17. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 879 ... South African Journal of Higher Education. ... Browse Title Index ... in a USA school setting: Merging transition theory with a narrative approach, Abstract ... Citation analysis of theses and dissertations submitted at the ...

  18. Browse Title Index

    African Journals Online (AJOL)

    Items 601 - 650 of 879 ... South African Journal of Higher Education. ... Browse Title Index .... The challenge of thesis supervision in an art university, Abstract ... No 2 (2004), Robert Sternberg's mental self-government theory and its contribution to ...

  19. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 533 ... Southern African Linguistics and Applied Language Studies. ... Issue, Title ... Vol 34, No 1 (2016), Book Review: Qualitative-Quantitative Analyses of .... The complex consonants of simple CV-syllables in Zezuru, Abstract.

  20. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 346 ... Journal Home > Advanced Search > Browse Title Index ... and hygiene promotion services in Rungwe district, Tanzania, Abstract .... as seen in NIgerian teaching hospital: pattern and a simple classification, Abstract.

  1. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 437 ... Journal Home > Advanced Search > Browse Title Index ... prospects and realistic strategies to its implementation in Nigeria\\'s Institute of ... and Communication Technology (ICT) in information dissemination, Abstract.

  2. Browse Title Index

    African Journals Online (AJOL)

    Items 901 - 950 of 1355 ... Journal of Applied Sciences and Environmental Management. ... Journal Home > Advanced Search > Browse Title Index .... Vol 22, No 2 (2018), Performance evaluation of a locally fabricated sawdust fired oven for ...

  3. Browse Title Index

    African Journals Online (AJOL)

    Items 301 - 350 of 788 ... Journal Home > Advanced Search > Browse Title Index ... Vol 26, No 1 (2018), Gender differentials in the perception of .... Vol 25, No 1 (2017), Impact of total quality management on students' academic performance in ...

  4. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 465 ... Journal Home > Advanced Search > Browse Title Index ... and twinning data of an igbo kindred during the Nigerian Civil War, Abstract ... on laboratory estimations with special reference to clinical chemistry, Abstract.

  5. Browse Title Index

    African Journals Online (AJOL)

    Items 251 - 300 of 1260 ... Journal Home > Advanced Search > Browse Title Index ... Consumption of ammonia-nitrogen by aob in immobilized batch culture, Abstract PDF .... Vol 9, No 3S (2017): Special Issue, Design an automatic temperature ...

  6. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 294 ... Journal Home > Advanced Search > Browse Title Index. Log in or .... S Edwards, M Hlongwane, J Thwala, N Robinson ... Vol 16, No 1 (2017), Infancy of internet cafe: The substitute of ubuntu-padare pedagogy, Abstract.

  7. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 130 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... using the technological pedagogical content knowledge(TPACK) framework, Abstract PDF ... Tamara N. Hrin, Dušica D. Milenković, Mirjana D. Segedinac.

  8. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 278 ... Journal Home > Advanced Search > Browse Title Index ... drie paradigmas beskou: 'n eenheid, of 'n veelheid van perspektiewe? ... Vol 45, No 1 (2011), Genre pedagogy in the mediation of socially-situated literacies ...

  9. Browse Title Index

    African Journals Online (AJOL)

    Items 551 - 600 of 879 ... Journal Home > Advanced Search > Browse Title Index ... A James, E Ralfe, L van Laren, N Ngcobo ... 1 (2011), Recognition of prior learning in promoting lifelong learning: A pedagogy of hope or a shattering of dreams?

  10. Browse Title Index

    African Journals Online (AJOL)

    Items 451 - 500 of 533 ... Journal Home > Advanced Search > Browse Title Index .... for past tense forms in Northern Sotho: verb stems with final 'm' and 'n', Abstract ... in an academic writing class: Implications for a dialogic pedagogy, Abstract.

  11. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 183 ... Journal Home > Advanced Search > Browse Title Index ... Vol 61 (2017), New interventions and sustainable solutions: .... Vol 35 (2011), Resurgence of tribal levies: Double taxation for the rural poor, Abstract PDF.

  12. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 736 ... Journal Home > Advanced Search > Browse Title Index ... Vol 5 (2008), A Contagious Malady: The Human Quest for Truth through Religion, Abstract ... A Study of Politeness Strategies Used by the National University of ...

  13. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 414 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... of an algebraic function for the permutation of truth table columns, Abstract ... appraisal and productivity levels in selected Nigerian universities, Abstract.

  14. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 879 ... Journal Home > Advanced Search > Browse Title Index ... Vol 20, No 4 (2006), Assessing academic potential for university admission: ... Vol 16, No 2 (2002), Book Review: Rethinking truth by Higgs, P & Smith, J, Details.

  15. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 165 ... Journal Home > Advanced Search > Browse Title Index ... Vol 43 (2011), Assessment of the Learning Commons takeoff at the University of ... the archive of South Africa's Truth and Reconciliation Commission, Abstract.

  16. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 644 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... Ethics review n international health research: quality assurance or bureaucratic nightmare? Details ... Audit of Management of Open Fractures, Details PDF.

  17. Browse Title Index

    African Journals Online (AJOL)

    Items 651 - 700 of 1199 ... Issue, Title ... Vol 5, No 1 (2011), Motivation, an Essential Ingredient for Optimal Performance in Emerging Markets, Abstract PDF ... Vol 3, No 5 (2009), Multinational transfer pricing and international taxation: what, why, ...

  18. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 153 ... Issue, Title. Vol 9, No 2 (2006):, Effects of efficient water utilisation on water resources development in Swaziland under climate change, Abstract .... Ethical, Indigenous and Socio-Economic Perspectives, Abstract.

  19. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 98 ... Journal Home > Advanced Search > Browse Title Index ... model for the continued professionalisation of student affairs in Africa, Abstract PDF ... Vol 2, No 2 (2014), Book Review: How College Affects Students, A Third decade ...

  20. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 76 ... Journal Home > Advanced Search > Browse Title Index ... Vol 4, No 1 (2011), Automation of AutoCAD for Detailing of Reinforced .... Vol 10, No 1 (2017), Housing data base for sustainable housing provision, Abstract PDF.

  1. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 147 ... Journal Home > Advanced Search > Browse Title Index .... Library (TEEAL) Database among faculty members in Federal University, ... Vol 5, No 2 (2014), Effects of corporate culture on the implementation of automation in ...

  2. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 41 of 41 ... Issue, Title ... Vol 1, No 3 (2004): Special Edition, Assessment of the quality and reserves of Bat ... Vol 1, No 1 (1997), Bovine dermatophilosis in Zambia: epidemiology, socio-economic impacts and future perspectives, Abstract.

  3. Browse Title Index

    African Journals Online (AJOL)

    Items 701 - 750 of 808 ... Issue, Title ... Vol 58, No 2 (2010), Short Communicaton: The socio-economic impact of helminth infections and the ... Vol 62 (2014): Special Edition, Special edition summarizing the scientific discourse which took place ...

  4. Browse Title Index

    African Journals Online (AJOL)

    Items 351 - 391 of 391 ... Issue, Title ... Vol 2, No 3 (1999): Special Edition, The efficacy of low volume application of roundup ... Vol 1, No 1 (1998), The relationships among National Socio-Economic Indicators and Child Health Statistics, Abstract.

  5. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 250 of 531 ... Journal Home > Advanced Search > Browse Title Index ... thermal conductivity and viscosity in a flat plate solar collector, Abstract PDF .... similarity method in unsteady two-dimensional MHD boundary layer on the body ...

  6. Drug‑Drug and Drug‑Nutraceutical Cocrystal/Salt as Alternative Medicine for Combination Therapy: A Crystal Engineering Approach

    Directory of Open Access Journals (Sweden)

    Ranjit Thakuria

    2018-02-01

    Full Text Available The pre-formulation of pharmaceutical cocrystals and salts is a concept of crystal engineering that has emerged as a promising technique for drug development in pharmaceutical industry. Recent introduction of pharmaceutical cocrystals in regulatory guidelines of US Food and Drug Administration (FDA made them one of the potential alternatives when salt preparation is not feasible. Apart from generally regarded as safe (GRAS coformers, drug‑drug and drug‑nutraceutical cocrystals are recent additions to pharmaceutical cocrystal family that have additional health benefits. Indeed, preparation of salt forms is a routine practice to deal with inadequacies associated with the active pharmaceutical ingredient (API and happens to be a potentially reliable method. Amongst them, drug-drug and drug-nutraceutical cocrystals have drawn significant importance in the recent past as they reduce drug load and cost effects during multiple disease diagnosis. However, one has to be prudent in the selection of drug molecules, the presence of complementary hydrogen bond synthon, disease management during multiple disease therapy, etc. that play important roles in their preparation. That is the reason why drug–drug cocrystals are scarce in the literature compared to pharmaceutical cocrystals containing GRAS coformers and salt forms. Herein, we discuss case studies preferably the reported drug‑drug, drug‑nutraceutical cocrystals, and a few salts with an emphasis on their role in physicochemical property modulation.

  7. Cold flow testing of the Space Shuttle Main Engine alternate turbopump development high pressure fuel turbine model

    Science.gov (United States)

    Gaddis, Stephen W.; Hudson, Susan T.; Johnson, P. D.

    1992-01-01

    NASA's Marshall Space Flight Center has established a cold airflow turbine test program to experimentally determine the performance of liquid rocket engine turbopump drive turbines. Testing of the SSME alternate turbopump development (ATD) fuel turbine was conducted for back-to-back comparisons with the baseline SSME fuel turbine results obtained in the first quarter of 1991. Turbine performance, Reynolds number effects, and turbine diagnostics, such as stage reactions and exit swirl angles, were investigated at the turbine design point and at off-design conditions. The test data showed that the ATD fuel turbine test article was approximately 1.4 percent higher in efficiency and flowed 5.3 percent more than the baseline fuel turbine test article. This paper describes the method and results used to validate the ATD fuel turbine aerodynamic design. The results are being used to determine the ATD high pressure fuel turbopump (HPFTP) turbine performance over its operating range, anchor the SSME ATD steady-state performance model, and validate various prediction and design analyses.

  8. Department of Transportation -- Exemption for using the Transuranic Package Transporter-I (TRUPACT-I) at the Idaho National Engineering Laboratory (Code of Federal Regulations, Title 49, Part 107, Subpart B -- Exemptions, 107-103 Application for Exemption)

    International Nuclear Information System (INIS)

    Tyacke, M.J.; Macdonald, R.J.

    1992-08-01

    Exemption from specific regulations is being sought for the Transuranic Package Transporter Model I (TRUPACT-I) container. The design has successfully undergone extensive testing of a quarter-scale model and a full-scale prototype of the container. Results from the analysis and testing are in the TRUPACT-1 Safely Analysis Report for Packaging (SARP), GA-Al8695/SAND 87-7104 (TTC0735), April 1987 (see Attachment 1). The container was never certified or used because of questions raised during the certification process. Two features of the container design failed to satisfy the regulations for Type B packaging. First, the design utilizes a venting system to control internal and external pressures; this venting system is not allowed by the Code of Federal Regulations, Title 10, Parts 71(h) and 71.51(b) [10 CFR 71.(h) and 71.51(b)]. Second, the maximum quantity fissile material proposed to be hauled in TRUPACT-I exceeded the limits in 10 CFR 71.63(b) for a single-containment container. To correct these design deficiencies, the vents would be plugged during transport, and the maximum quantity of fissile material would be limited to the allowables for a single-containment container. An engineering analysis showed that the container could safely transport radioactive material within the boundaries of the Idaho National Engineering Laboratory (INEL) with the vent system plugged (see Attachment 2). However, some of the requirements for determining pressure on a container need to be changed (i.e., exempted) to reflect conditions unique to the INEL. The following are the requirements needing to be changed for INEL conditions, variances being sought, and justifications for the variances

  9. Engines of alternative objectivity: Re-articulating the nature and value of participatory mental health organisations with the Hearing Voices Movement and Stepping Out Theatre Company.

    Science.gov (United States)

    Blencowe, Claire; Brigstocke, Julian; Noorani, Tehseen

    2018-05-01

    Through two case studies, the Hearing Voices Movement and Stepping Out Theatre Company, we demonstrate how successful participatory organisations can be seen as 'engines of alternative objectivity' rather than as the subjective other to objective, biomedical science. With the term 'alternative objectivity', we point to collectivisations of experience that are different to biomedical science but are nonetheless forms of objectivity. Taking inspiration from feminist theory, science studies and sociology of culture, we argue that participatory mental health organisations generate their own forms of objectivity through novel modes of collectivising experience. The Hearing Voices Movement cultivates an 'activist science' that generates an alternative objective knowledge through a commitment to experimentation, controlling, testing, recording and sharing experience. Stepping Out distinguishes itself from drama therapy by cultivating an alternative objective culture through its embrace of high production values, material culture, aesthetic standards. A crucial aspect of participatory practice is overcoming alienation, enabling people to get outside of themselves, encounter material worlds and join forces with others.

  10. Investigation of a 7-pole/6-slot Halbach-magnetized permanent-magnet linear alternator used for free-piston stirling engines

    Science.gov (United States)

    Zheng, Ping; Tong, Chengde; Zhao, Jing; Yu, Bin; Li, Lin; Bai, Jingang; Zhang, Lu

    2012-04-01

    This paper investigates a 7-pole/6-slot Halbach-magnetized permanent-magnet linear alternator used for free piston Stirling engines (FPSEs). Taking the advantages of Halbach array, a 1 kW prototype alternator is designed. Considering the rms value of electromotive force (EMF) and harmonic distortion, the optimal length ratio of the axial- and radial-magnetized permanent magnets and thicknesses of the permanent magnets are optimized by 2D finite element method. The alternator detent force, which is an important factor for smooth operation of FPSEs, is studied by optimizing slot tip and end tooth. The load and thermal performances of the final design are simulated. A prototype alternator was designed, built and tested. Experimental data indicated satisfactory design.

  11. New Bedford Harbor Superfund Project, Acushnet River Estuary Engineering Feasibility Study of Dredging and Dredged Material Disposal Alternatives. Report 11. Evaluation of Conceptual Dredging and Disposal Alternatives

    Science.gov (United States)

    1989-07-01

    Y -- ma ma"o DIVIDENDS~~ 13ATUR -P 313ARM CORPS OF ENGINEERS A D z-. - N K 4 F~~ 1 /V. E C 7- GENERAL NOTES: - Soundtags are in fget a td t enths aid...usoAdter ine stae. Til %format ion depicted on these saps represents Ihq results of surveyjs made on the dates ihdica ted Ogu Ce on Iy .e Couasderedtas

  12. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 25, No 2 (2005), Yam-based farm practices and nematode problems in stored yams (Dioscorea spp.) in Ghana, Abstract PDF. CK Kwoseh, RA Plowright, J Bridge, R Asiedu. Vol 27, No 2 (2007), Yield, irrigation production efficiency and economic returns of broccoli under variable drip irrigation and lateral ...

  13. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 68 of 68 ... Issue, Title. Vol 12, No 1-2 (2009), Sécurité et ordre politique au Cameroun : entre dynamiques internes et connexions internationales, Abstract PDF. BEP Chantal. Vol 6, No 1-2 (2003), Self-Determination, Nationalism, Development and Pan-Africanism Stuck on the Runway: Are Intellectuals to be Blamed ...

  14. Browse Title Index

    African Journals Online (AJOL)

    Items 551 - 600 of 1463 ... Issue, Title. Vol 15, No 2 (2015), Evaluation of the diagnostic performance and operational characteristics of four rapid immunochromatographic syphilis tests in Burkina Faso, Abstract PDF. FY Bocoum, H Ouedraogo, G Tarnagda, A Kiba, S Tiendrebeogo, F Bationo, B Liestman, S Diagbouga, ...

  15. Browse Title Index

    African Journals Online (AJOL)

    Items 351 - 400 of 400 ... Issue, Title. Vol 9, No 1 (2010), Soft tissue sarcoma of the thigh: Need for angiography in the developing, Abstract PDF. IA Adigun, GA Rahman, KO Ogundipe. Vol 3, No 1 (2004), Spectrum of rheumatic heart disease in Zaria, Northern Nigeria, Abstract. SS Danbauchi, MA Alhassan, SO David, ...

  16. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 183 ... Issue, Title. Vol 62 (2017), #SchoolsOnFire: Criminal justice responses to protests that impede the right to basic education, Abstract PDF. Ann Skelton, Martin Nsibirwa. Vol 45 (2013), 'Pale Face'/'Pointy Face: SA Criminology in Denial, Abstract PDF. S Henkeman. Vol 59 (2017), Aluta continua: Police ...

  17. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 14 of 14 ... Issue, Title. Vol 2, No 1 (2009), Auditory and Respiratory Health Disorders Among Workers in an Iron and Steel Factory, Abstract. GM Abdel – Rasoul, OAE Mahrous, ME Abou Salem, MA Al-Batanony, HK Allam. Vol 2, No 1 (2009), Effect of An Educational Program About Medical Waste Management on ...

  18. Browse Title Index

    African Journals Online (AJOL)

    Items 251 - 300 of 490 ... Issue, Title. Vol 6, No 2 (2010), Knowledge and patterns of use of highly active antiretroviral therapies in HIV management at Abuja, Nigeria, Abstract. Jill I Okpalugo, US Inyang, K Ibrahim, F Anita, Chinwe V Ukwe, NC Aguwa. Vol 5, No 4 (2009), Knowledge and utilization of the acts in two major ...

  19. Browse Title Index

    African Journals Online (AJOL)

    Items 9951 - 10000 of 11090 ... Issue, Title. Vol 10, No 36 (2011), Study of heavy metals bioaccumulation in the process of vermicomposting, Abstract PDF. MM Aleagha, G Ebadi. Vol 10, No 45 (2011), Study of malondialdehyde (MDA) content, superoxide dismutase (SOD) and glutathione peroxidase (GSH-Px) activities in ...

  20. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 412 ... Issue, Title. Vol 32, No 2 (2013), Seinsverständnis and meaning in Heidegger, Abstract. Rafael Winkler. Vol 21, No 3 (2002), A defense of peace as a human right, Abstract. Patrick Hayden. Vol 26, No 2 (2007), A Kantian stance on teleology in biology, Abstract. AA Cohen. Vol 30, No 1 (2011), A Likely ...

  1. Browse Title Index

    African Journals Online (AJOL)

    Items 251 - 300 of 328 ... Issue, Title. Vol 7, No 1 (2003), Sexual Harassment in Academia in Nigeria: How Real? Details PDF. Olugbenga Jelil Ladebo. Vol 8, No 2 (2004), Shaping the internet for match-making/dating: a challenge for the contemporary Nigerian family institution, Abstract PDF. Wale Adesina. Vol 6, No 1 (2002) ...

  2. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 73 of 73 ... Journal Home > Advanced Search > Browse Title Index ... Vol 13 (2006), The ageing eye” functional changes from cradle to gray: A ... Vol 12 (2005), The evaluation of vision in children using monocular vision acuity and ...

  3. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 22, No 2 (2008), Voltammetric determination of heparin based on its interaction with malachite green, Abstract PDF. Xueliang Niu, Weili Zhang, Na Zhao, Wei Sun. Vol 22, No 2 (2008), Voltammetric determination of l-cysteic acid on a 1-[4-(ferrocenyl-ethynyl)phenyl]-1-ethanone modified carbon paste ...

  4. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 250 of 577 ... Issue, Title. Vol 20, No 2 (2003), Emergency Contraception: A Global Overview of Knowledge, Attitudes and Practices Among Providers, Abstract PDF. Deborah Haggai. Vol 23 (2006):, Emergency laparotomy for peripartum haemorrhage in Bida North Central Nigeria, Abstract PDF. Sunny Abiodun O ...

  5. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 250 of 11090 ... Issue, Title. Vol 12, No 49 (2013), In vitro regeneration of selected Kenyan papaya (Carica papaya L.) lines through shoot tip culture, Abstract PDF. Naomi Nzilani Mumo, Fredah Karambu Rimberia, George Edward Mamati, Agnes Wanjiru Kihurani. Vol 7, No 12 (2008), In vitro regeneration of Turkish ...

  6. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 221 ... Issue, Title ... Vol 38 (2010), Soft drink consumption of Grade 4 and Grade 7 learners in the Wynberg area, City of Cape Town, South .... Vol 42 (2014), The meaning of food for obese men: a qualitative study, Abstract PDF.

  7. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 1215 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... Vol 12, No 1 (2018), Analysis of the effects of frequent strikes on academic performance of students in universities in Nigeria: Edo State as a focal point, Abstract PDF ... Vol 6, No 1 (2012), Appraisal as a Determinant for Adequate ...

  8. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 20 of 20 ... Issue, Title. Vol 9, No 2 (2000), Age dependent changes in the hypothalamic amino acid neurotransmitters in response to nicotine, Abstract. NM Radwan, NA Ahmed, YAM Aly. Vol 9, No 2 (2000), Autoantibodies, ocular and auditory changes in patients with vitiligo, Abstract. AE Fathia, EA Nagwa, ...

  9. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 76 of 76 ... Issue, Title. Vol 6, No 1 (2013), Integrating Sustainability into the Real Estate Valuation Process: A Nigerian Perspective, Abstract PDF. G K Babawale, B A Oyalowo. Vol 5, No 1 (2012), Internalising internationa valuation standards: Relevance and applicability issues in the Nigerian context, Abstract PDF.

  10. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 201 ... Issue, Title. Vol 12, No 1 (2006), Conservative management of cervical ectopic pregnancy: case report, Abstract PDF. TD Naidoo, MR Ramogale, J Moodley. Vol 18, No 2 (2012), Contraceptive use and associated factors among South African youth (18 - 24 years): A population-based survey, Abstract ...

  11. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 183 of 183 ... Issue, Title. Vol 9, No 1 (2004), Socio-economic constraints affecting youths involvement in national economic development, Abstract. Josephine U Nwagwu. Vol 12, No 2 (2007), Stabilizing Potential Of Cement-Fly Ash Mixture On Expansive Clay Soil, Abstract. OO Amu, AB Fajobi, SO Afekhuai. Vol 11 ...

  12. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 76 ... Issue, Title. Vol 16, No 2 (2006), A profile of the theatre procedures in paediatrict ophthalmic practice, Abstract. E O Onwasigwe. Vol 15, No 2 (2005), Abdominal cocoon, Abstract. Abdulrasheed K Adesunkanmi, Tajudeen A Badmus, Olukayode Ogundoyin, Akinwumi B Ogunrombi. Vol 18, No 1 (2008) ...

  13. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 647 ... Issue, Title. Vol 13, No 2 (2010), 'N toekomstige perspektief op grondwetlike stabiliteit, Abstract PDF. F.W de Klerk. Vol 18, No 5 (2015), Cloete murray and Another v Firstrand bank ltd t/a Wesbank [2015] ZASCA 39A, Abstract PDF. M Laubscher. Vol 15, No 5 (2012), Cave Pecuniam: Lawyers as ...

  14. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 15 of 15 ... Issue, Title. Vol 1, No 1 (2008), Assessment Of Ophthalmic Patients' Satisfaction In Owo, Abstract. CO Omolase, CO Fadamiro, BO Omolase, AS Aina, EO Omolade. Vol 3, No 1 (2010), Case Report: Strongyloides stercoralis coinfection in a Nigerian with HIV. Abstract. A.A Oyekunle, R.A.A Bolarinwa, O.A ...

  15. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 15 of 15 ... Issue, Title. Vol 1, No 1 (2007), An Action Five Strategy For Bridging The Gender Gap In Academic Research Activities In African Universities. The Case of Nigeria, Abstract PDF. DN Okorie, OG Agabi, CM Uche. Vol 1, No 1 (2007), Book Review: Confronting sexual harassment in Ghanaian Universities ...

  16. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 93 ... Issue, Title. Vol 5 (2013), A cost-effective Geographic Information Systems for Transportation (GIS-T) application for traffic congestion analyses in the Developing World, Abstract PDF. E Agyemang. Vol 3 (2011), A Historical and Gendered Perspective on HIV / AIDS in Botswana, Abstract PDF. J Hesselberg ...

  17. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 250 of 327 ... Issue, Title. Vol 10, No 4 (2016), Omphalocoeles: A decade in review, Abstract PDF. S Singh, A Madaree. Vol 2, No 4 (2008), Ortner syndrome, Abstract PDF. E Meyer, NE Jones, LJ Zühlke. Vol 10, No 3 (2016), Outcome of children admitted to a general highcare unit in a regional hospital in the ...

  18. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 814 ... Issue, Title. Vol 21, No 2 (2016), A 10 years trend of peptic ulcer disease and other gastrointestinal disorders in northern Uganda, Abstract PDF. T.R. Okello, D.M. Ogwang, I Pecorella. Vol 21, No 2 (2016), A 2-years description of traumatic brain injury admissions in Tikur Anbessa Specialized Hospital ...

  19. Browse Title Index

    African Journals Online (AJOL)

    Items 301 - 350 of 577 ... Issue, Title. Vol 32, No 2 (2015), Late arrival in hospital during labour: any correlation with materno-foetal outcome? The state specialist hospital, Asubiaro, Osogbo Experience. Abstract PDF. OO Awolola. Vol 30, No 2 (2013), Late Reproductive Effects of Cancer Treatment in Young People, Abstract ...

  20. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 319 ... Issue, Title. Vol 23, No 2 (2016), Carica papaya juice enhanced in-vitro cell proliferation better than freeze-dried PBS extract using scratch assay, Abstract. A.B. Nafiu, E Abdulaziz, M.T. Rahman. Vol 23, No 2 (2016), A comparative study of the ownership and utilization of insecticide treated nets in ...

  1. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 52 ... Issue, Title. Vol 15 (2000), Ammi analysis of maize yield trials in South-Western Nigeria, Abstract. SR Ajibade, BA Ogunbodede. Vol 20 (2006), Association of yield with some agronomic characters in potatoes in a cool mid-altitude location, Abstract. CO Amadi, EE Ene Obong. Vol 20 (2006), Casein (CSN3) ...

  2. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 240 of 240 ... Issue, Title. Vol 8, No 4 (2005), Status equipment in primary health centres of Tafa Lga, North Central Nigeria, Abstract. MN Sambo, I Lewis, K Sabitu. Vol 10, No 1 (2007), Stroke at a tertiary medical institution in Northern Nigeria: Patients\\' profile and predictors of outcome, Abstract. KW Wahab, MU ...

  3. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 249 ... Issue, Title. Vol 10, No 1 (2010), Ye Shakoch Chilot (the court of the sheikhs): A traditional institution of conflict resolution in Oromiya zone of Amhara regional state, Ethiopia, Abstract PDF. M Zeleke. Vol 15, No 3 (2015), A comparative analysis of the Post- Arab Spring National Dialogues in Tunisia and ...

  4. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 670 ... Issue, Title. Vol 9, No 2 (2012), Business Planning and the Economic Growth of Small and Medium Scale Enterprises in Nigeria, Abstract. Egbe Aneozeng A, Ejoh Ndifon Ojong, Obo Ekpenyong Bassey. Vol 11, No 2 (2014), Calabar Humaphors: An Analysis of Selected Jokes in Nigerian Stand Up ...

  5. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 107 of 107 ... Issue, Title. Vol 6, No 1 (2017), The Ophthalmic status manifestations of nutritional and lifestyle disorders of men in a peri urban community in Ghana, Abstract PDF. F. Vuvor, M. Steiner-Asiedu, F.K. Saalia. Vol 2, No 1 (2013), Thyroid Disorders in Accra, Ghana: A Retrospective Histopathological Study ...

  6. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 165 ... Issue, Title. Vol 30 (2005), Digitisation projects at the University of Cape Town Libraries, Abstract. Janine Dunlop, Lesley Hart. Vol 24 (2002), DISA: an African Perspective on Digital Technology, Abstract. Michele Pickover, Dale Peters. Vol 30 (2005), Doing it right – or are we? Basic principles in the ...

  7. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 251 ... Issue, Title. Vol 55 (2014), 20 Years of democracy: Transforming the public service, Abstract. A Ruiters. Vol 63 (2016), Zemk' iinkomo magwala ndini! Wake up! The cows are being stolen! Abstract. Sipho Pityana. Vol 56 (2014), A layperson's guide to Nene's budget statement, Abstract. B Turok.

  8. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 1007 ... Issue, Title. Vol 11, No 1 (1997), (+)-Floribundone 3 from the pods of Senna septemtrionalis, Details PDF. Gizachew Alemayehu, Bekuretsion Woldeyesus, Berhanu M Abegaz. Vol 14, No 1 (2000), 11α-Hydroxy muzigadiolide, a novel drimane sesquiterpene from the stem bark of warburgia ugandensis ...

  9. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 356 ... Issue, Title. Vol 27, No 3 (2014), A desire for weight loss in season increases disordered eating behaviour risk and energy deficiency in athletes, Abstract PDF. HH Wright, R Ford, CR Botha. Vol 29, No 3 (2016), A review of infant and young child feeding practice in hospital and the home in KwaZulu-Natal ...

  10. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 66 ... Issue, Title. Vol 48, No 1-2 (2015), A hierarchical modeling of information seeking behavior of school teachers in rural areas of Nigeria, Abstract. Manir Abdullahi Kamba. Vol 49, No 1-2 (2016), Access to electronic information resources by students of federal college of education in south east Nigeria ...

  11. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 683 ... Issue, Title. Vol 54, No 1 (2006), Bovine tuberculosis survey in urban and peri urban dairy farms in coastal humid region of Tanga, Tanzania, Abstract. ES Swai, G Shirima, S Bwanga, W Moshy. Vol 60, No 3 (2012), Browsing capacity and nutritive value of indigenous browses in a tropical Coastal ...

  12. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 387 ... Issue, Title. Vol 15, No 2 (2015), Introduction to Christian philosophy, Abstract. Charles Ogundu Nnaji. Vol 8, No 2 (2006), Is Quantum Mechanics a Complete Theory?: A Philosophical Defense of Einstein's Position, Abstract. U O Egbai. Vol 10, No 1 (2007), Jesus in Africa, Abstract. FF Edet. Vol 10, No ...

  13. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 98 of 98 ... Issue, Title. Vol 4, No 1 (2016), First-year seminar intervention: Enhancing firstyear mathematics performance at the University of Johannesburg, Abstract PDF. Melanie Jacobs, Estherna Pretorius. Vol 5, No 2 (2017), From Inky Pinky Ponky to Improving Student Understanding in Assessment: Exploring the ...

  14. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 167 of 167 ... Issue, Title ... Vol 2, No 2 (2013), Women and the Leadership Paradigm: Bridging the Workplace Gender-Gap in Nigeria, Abstract PDF ... Vol 5, No 2 (2016), Women's participation and gender issues in local governance ...

  15. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 110 ... Issue, Title. Vol 10, No 1 (2003), Incidence and Determinants of Child Labour in Nigeria: Implications for Poverty Alleviation, Abstract. Benjamin Chiedozie Okpukpara, Ngozi Odurukwu. Vol 20, No 1 (2013), Inflation and capacity utilisation in Nigeria's manufacturing sector, Abstract. OA Ishola. Vol 19, No ...

  16. Browse Title Index

    African Journals Online (AJOL)

    Items 251 - 300 of 367 ... Issue, Title. Vol 43 (2014), Some interlingual communicative challenges for foreign African interpreters in South African courtrooms, Abstract PDF. SE Usadolo, E Kotze. Vol 29 (1996), South Africa's new language policy in the context of the organisation for African unity's language plan of action for ...

  17. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 89 ... Issue, Title ... of two-phased approaches to load balancing in cloud computing, Abstract ... Vol 19, No 1 (2012), Assessing Network Services and Security in ... Vol 23, No 1 (2016), Cloud model construct for transaction-based ...

  18. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 198 ... Issue, Title ... Vol 13, No 1 (2015), Biometric Enhancement of Home and Office Security to Reduce Assassinations in Nigeria, Abstract PDF ... Vol 9, No 1 (2013), Cloud Computing: Key to IT Development in West Africa ...

  19. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 198 of 198 ... Issue, Title ... scheme for QoS and energy conservation in cloud computing, Abstract PDF ... Vol 9, No 1 (2013), Performance and Security Evaluation of ... Vol 18, No 1 (2017), Reducing capital flight through local cloud ...

  20. Browse Title Index

    African Journals Online (AJOL)

    Items 251 - 300 of 652 ... Journal Home > Advanced Search > Browse Title Index ... Vol 18, No 7 (2015), Introduction to virtual property: Lex virtualis ipsa ... Vol 17, No 1 (2014), Legal challenges relating to the commercial use of outer space, with ...

  1. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 170 of 170 ... Issue, Title. Vol 20, No 2 (2004), The Impact of Mine Closures on Rural Population Dynamics: The Case of Zhombe in Kwekwe District, Midlands Province, Zimbabwe, Abstract. Crescentia Madebwe. Vol 29, No 1 (2013), The Influence of Organisational Culture and Job Satisfaction on Intentions to ...

  2. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 263 ... Issue, Title. Vol 1, No 2 (2002), Effect of Light and Darkness on Packed Cell Volume in the Rat, Abstract. A. A. OSINUBI, F. I. DURU, C. C. NORONHA, A. O. OKANLAWON. Vol 4, No 1 (2005), Effect of Marijuana Smoking on Blood Chemistry and Serum Biogenic Amines Concentrations in Humans ...

  3. Browse Title Index

    African Journals Online (AJOL)

    Items 751 - 800 of 846 ... Journal Home > Advanced Search > Browse Title Index ... Vol 9, No 3S (2017): Special Issue, The effect of torrefaction on oil palm ... core competency skills of IRBM tax auditors towards their performance, Abstract PDF ... of exchange rates behavior in Malaysia by using NATREX model, Abstract PDF.

  4. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 38, No 1 (2004), Book Review: Unexpected Voices – Theory, Practice and Identity in the Writing Classroom. Abstract. Charly Dyers. Vol 38, No 1 (2004), Book Review: Shelley Angelil-Carter: Stolen Language? Plagiarism in Writing. Abstract. Elizabeth de Kadt. Vol 37, No 1 (2003), Book Review: The Green ...

  5. Browse Title Index - AJOL

    African Journals Online (AJOL)

    Items 501 - 508 of 508 ... Issue, Title. Vol 33, No 2 (2011), Visuele stereotipering van sportvroue in die sportmedia, Abstract. M Brandt, A Carstens. Vol 30, No 1 (2008), Volunteers\\' perceptions of benefits derived from volunteering: an empirical study, Abstract. J Surujlal, M Dhurup. Vol 33, No 1 (2011), Was the Conconi test ...

  6. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 108 of 108 ... Issue, Title. Vol 8, No 2 (2016), The status and challenges of clinical informatics development in South Africa, Abstract PDF. Abayomi Kehinde Owolabi, Thokozani Patrick Mhlongo, Neil Evans. Vol 4, No 1 (2012), The stuttering implementation of language policies in the South African education system ...

  7. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 100 ... Issue, Title. Vol 28 (2013): Special Issue, Occurrence of Cryptosporidium and Giardia in domestic animals in peri-urban communities of Kafue district, Zambia, Abstract. J Siwila, IGK Phiri, HI Enemark, M Nchito, A Olsen. Vol 26, No 1 (2009), Occurrence of foot and mouth disease serotypes in Tanzania: A ...

  8. Browse Title Index

    African Journals Online (AJOL)

    Items 801 - 850 of 11090 ... Issue, Title. Vol 10, No 61 (2011), Analysis of chemical constituents in medicinal plants of selected districts of Pakhtoonkhwa, Pakistan, Abstract PDF. I Hussain, R Ullah, J Khan, N Khan, M Zahoor, N Ullah, MuR Khattak, FA Khan, A Baseer, M Khurram. Vol 10, No 77 (2011), Analysis of chloroplast ...

  9. Browse Title Index

    African Journals Online (AJOL)

    Items 501 - 550 of 670 ... Issue, Title. Vol 11, No 4 (2014), Strategies for Fostering Creativity Among Business Education Graduates in Nigeria, Abstract. BO Nwosu, KE Ojo. Vol 13, No 1 (2015) ... Vol 10, No 1 (2013), The Challenges Facing Accounting Education: The Nigerian Experience, Abstract. OR Okolie. Vol 5 (2008), The ...

  10. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 198 ... Issue, Title ... Vol 7, No 1 (2013), Enterprise Cloud Adoption: Leveraging on the Business ... Load Balancing And Job Scheduling In Cloud Computing ... Vol 13, No 1 (2015), ICT-Based Framework for Improved Food Security in Nigeria ... Vol 5, No 1 (2012), IT-Based Solutions to the Electoral System in ...

  11. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 1117 ... Journal Home > Advanced Search > Browse Title Index ... Vol 13, No 3 (2007):, an edu-ethical perspecitve on the nature of truth: case studies in elite ... 2009: September: Supplement, An empirical study of university ...

  12. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 20, No 1 (2015), Assessment of iron status among preschool children (6 to 59 months) with and without malaria in Western Province, Kenya, Abstract. I Kisiangani, C Mbakaya, A Makokha, D Magu. Vol 20, No 1 (2015), Assessment of iron status among preschool children (6 to 59 months) with and without ...

  13. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 232 ... Issue, Title. Vol 5 (2003), Pre-School Education for a Democratic Society: Identifying Views of Stakeholders in Tanzania, Abstract. Willy LM Komba, Satoki T Mahenge, Gadi Koda. Vol 13, No 2 (2012), Process of Assuring Quality in Counselling at the National Open University of Nigeria: A Critique ...

  14. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 1732 ... Journal Home > Advanced Search > Browse Title Index ... Vol 10, No 3 (2007), An Audit Of Perioperative Cardiac Arrest At ... Vol 11, No 4 (2008), An Audit Of Rejected Repeated X-ray Films As A Quality Assurance ...

  15. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 1038 ... Issue, Title. Vol 31, No 2 (2009), Assessing the utility of a continuous, underway fish egg sampler (CUFES) for sampling zooplankton, Abstract. S Sono, CL Moloney, CD van der Lingen. Vol 38, No 4 (2016), Assessing trophic adaptability is critical for understanding the response of predatory fishes to ...

  16. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 101 ... Issue, Title. Vol 3, No 4 (2014), Chlamydia trachomatis IgG antibodies seroprevalence among students in two tertiary institutions in Anambra state, Nigeria: a comparative study, Abstract PDF. CB Duru, FE Emele, ED Adinma, CO Ifeadike, KA Uwakwe, AO Oluboyo, BO Oluboyo, C Abejegah. Vol 2, No 1 ...

  17. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 250 of 367 ... Issue, Title. Vol 42 (2013), Nursing the Cure: A Phonetic Analysis of /ʊə/ in South African English, Abstract PDF. I Bekker. Vol 1 (1980), Nuwe ontwikkelings binne chomsky se teorle van kerngrammatika, Abstract PDF. J Maartens. Vol 42 (2013), Obligatory Reflexivity in a Minimalist Grammar of ...

  18. Browse Title Index

    African Journals Online (AJOL)

    Items 651 - 700 of 1007 ... Issue, Title. Vol 4, No 1 (1990), Kinetics of oxidation of β-diimihe macrocyclic complexes and accessibility of six-coordinate copper(III) complexes generated by electrochemical oxidation of copper(II) complexes, Abstract PDF. Mohamed A. Khalifa. Vol 14, No 2 (2000), Kinetics of periodate oxidation of ...

  19. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 1020 ... Issue, Title ... Vol 48, No 2 (2006), Barriers to HIV Care and Treatment by Doctors: A review of the literature. ... Vol 48, No 5 (2006), Breast cancer – early detection and screening in South African women from the ...

  20. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 23, No 2 (2011), Dynamique foliaire et croissance du maïs: Application du modèle «STICS» en conditions tropicales en RD-Congo, Abstract PDF. MM Lufuluabo, RV Kizungu, KK Nkongolo. Vol 18, No 1 (2006), Dynamique spatio-temporelle des populations d\\'Altises Podagrica spp. (Coleoptera ...

  1. Browse Title Index

    African Journals Online (AJOL)

    Items 251 - 300 of 2005 ... Issue, Title. Vol 92, No 4 (2015), Blood Pressure and Obesity Index Assessment in a Typical Urban Slum in Enugu, Nigeria, Abstract. GI Ahaneku, CU Osuji, OC Oguejiofor, BC Anisiuba, VO Ikeh, JE Ahaneku. Vol 80, No 10 (2003):, Blood pressure control in a population where antihypertensives are ...

  2. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 250 of 661 ... Journal Home > Advanced Search > Browse Title Index. Log in or Register to get access to full text downloads. .... A El-Mahdy, B Bolduc, J Upadhyay, R Shoukr, A Khoury. Vol 19, No 1 (2013), Factors affecting lower calyceal stone clearance after Extracorporeal shock wave lithotripsy, Abstract PDF.

  3. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 286 ... Issue, Title. Vol 2, No 3-4 (2008), Impact of fire wood collection on trees species diversity in Bauchi state, Nigeria, Abstract. A Nura, A Ibrahim, I Mohammed, U Haruna. Vol 5, No 3 (2011), Impact of national special program for food security in Abia State, nigeria, Abstract. CO Emerole. Vol 5, No 1 (2011) ...

  4. Browse Title Index

    African Journals Online (AJOL)

    Items 351 - 400 of 979 ... Issue, Title. Vol 45, No 9 (2003), Erectile dysfunction: A GP's guide to clinical assessment, Abstract PDF. PJ Harden. Vol 47, No 4 (2005), Ethical Issues in Family Practice: My Culture – Right or Wrong? Abstract PDF. GA Ogunbanjo, D Knapp van Bogaert. Vol 59, No 3 (2017), Ethical issues with ...

  5. Browse Title Index

    African Journals Online (AJOL)

    Items 301 - 350 of 745 ... Issue, Title. Vol 9, No 3 (1999), Frequency And Outcome In AIDS Patients In A University Teaching Hospital – A Five Year Review, Abstract. SA Ogun, OO Adelowo, AEA ... Vol 18, No 2 (2008), Good cllinical practice in clinical drug trials - What you need to know, Abstract. K Soyebi, Y Abosede, HAB ...

  6. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 217 ... Browse Title Index. Journal Home > Advanced ... Vol 13, No 1 (2016), Access to specialized surgical care, Abstract PDF. H Saidi ... Vol 9, No 2 (2012), Clinical Assessment of the Palmaris Longus – Accuracy of common tests, Abstract PDF ... Vol 11, No 2 (2014), Clinical trials in Surgery, Abstract PDF.

  7. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 633 ... Issue, Title. Vol 19, No 1 (2009), Delays in Tuberculosis Treatment and Associated Factors in Jimma Zone, Southwest Ethiopia, Abstract PDF. Ayalew Tegegn, Meseret Yazachew. Vol 26, No 1 (2016), Delivery Site Preferences and Associated Factors among Married Women of Child Bearing Age in ...

  8. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 4119 ... Issue, Title. Vol 86, No 2 (1996), A re-evaluation of isotope screening for skeletal metastases in nodenegative breast cancer, Abstract PDF. C.A. Gudgeon, I.D. Werner, D.M. Dent. Vol 104, No 6 (2014), A reflection on the South African Medical Association – past, present and future, Abstract PDF.

  9. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 250 of 1006 ... Issue, Title. Vol 49, No 8 (2007), Clinical approach to a patient with abnormal uterine bleeding, Abstract PDF. B G Lindeque. Vol 57, No 5 (2015), Clinical evidence in the management of swimmer's ear, Abstract PDF. Andre Marais. Vol 50, No 1 (2008), Clinical features of Systemic Lupus ...

  10. Browse Title Index

    African Journals Online (AJOL)

    Items 701 - 750 of 1010 ... Issue, Title. Vol 6, No 2 (1998), Performance et stabilité de rendement des génotypes de patate douce dans divers environnements à l'est du Congo, Abstract. P Phemba, T Mutombo, N B Lutaladio, E E Carey. Vol 22 (2014): Supplement, Performance of Artemia shell-free embryos, Moina micrura and ...

  11. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 17 (2005), A. C. conduction behaviour in amorphous WO3/CEO2 thin film, Abstract. B Yagoubi, C A Hogarth, A Boukorrt. Vol 16 (2003), A lossless image compression algorithm using variable block size segmentation, Abstract. Z Brahimi, K A Saadi, N Baraka. Vol 15 (2003), Analysis method of wavelet ...

  12. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 97 of 97 ... Journal Home > Advanced Search > Browse Title Index ... Vol 20, No 2 (2008), Research Note: Anthropometric data of the foot of ... Vol 26, No 1 (2014), Validation of the Automation Attitude Questionnaire for Airline Pilots ...

  13. Titles of Midas

    Directory of Open Access Journals (Sweden)

    G. L. Huxley

    2001-09-01

    Full Text Available The Phrygian inscription on the tomb at Yazılıkaya (8th century gives Midas the titles wanax and lawagtas, paralled in Mycenaean, and there were strong connections between his dynasty and Greek Aeolis.

  14. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 250 of 333 ... Issue, Title. Vol 15, No 1 (2016), Irrigation potential of Inuakpa in Odukpani local government of Cross river using Kostiakov model, Abstract PDF. B.O. Unuigbe, K.I. Ofem, N.R.B. Antigha. Vol 2, No 2 (2003), LABOUR USE IN SMALL-SCALE YAM PRODUCTION IN QUA'AN PAN LOCAL GOVERNMENT ...

  15. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 644 ... Issue, Title. Vol 19, No 2 (2007), A qualitative study of medical student socialization in Malawi\\'s College of Medicine: Clincal crisis and beyond, Abstract PDF. C Wendland, C Bandawe. Vol 19, No 2 (2007), A qualitative study of medical student socialization in Malawi\\'s College of Medicine: Preclinical ...

  16. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 13, No 2 (2013), Using Mindfulness as a Teaching Aid for Phenomenology, Abstract PDF. IR Owen. Vol 8, No 1 (2008), Were Nietzsche's Cardinal Ideas – Delusions? Abstract PDF. Eva M Cybulska. Vol 12, No 1 (2012), What did you learn in school today? Abstract PDF. Carina Henriksson. Vol 5, No 1 (2005) ...

  17. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 265 ... Issue, Title. Vol 35, No 2 (2008), Choice of place for childbirth: prevalence and correlates of utilization of health facilities in Chongwe district, Zambia, Abstract PDF. AN Hazemba, S Siziya. Vol 43, No 1 (2016), Clinical and Radiological Features of Multiple Myeloma Patients at the University Teaching ...

  18. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 88, No 8 (1998), New birth and death registration forms - a foundation for the future, a challenge for health workers? Abstract PDF. Debbie Bradshaw, Danuta Kielkowski, Freddy Sitas. Vol 83, No 3 (1993), New estimates of infant and child mortality for blacks in South Africa, 1968-1979, Abstract PDF.

  19. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 643 ... Issue, Title. Vol 18, No 2 (2015), Contraceptive Knowledge and Compliance with Guidelines for Providing Contraceptive Services by Patent Medicine Vendors In Ibadan North Local Government Area, Nigeria, Abstract PDF. OO Ajayi, AJ Ajuwon. Vol 16, No 2 (2013), Coping Strategy for Food Security ...

  20. Browse Title Index

    African Journals Online (AJOL)

    Items 851 - 900 of 1006 ... Issue, Title. Vol 54, No 2 (2012), The effect of the introduction of a standard monitoring protocol on the investigations performed on the metabolic control of type 2 diabetes at Addington Hospital Medical Outpatients Department, Durban, South Africa, Abstract PDF. JM Gill, A Ross, F Pirie, ...

  1. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 8, No 2 (2016): Supplement, Using operative models (ICF and CBR) within an interprofessional context to address community needs, Abstract PDF. A Rhoda, F Waggie, G.C. Filies, J.M. Frantz. Vol 2, No 1 (2010), Using portfolios to assess professional competence and development in medical laboratory ...

  2. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 412 ... Issue, Title. Vol 30, No 3 (2011) ... Transferring the principle of double effect from war to business, Abstract. G. J. Rossouw ... Vol 22, No 2 (2003), Can more business ethics teaching halt corruption in companies? Abstract.

  3. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 155 ... Issue, Title. Vol 12 (2012), Political Dissent and Autonomy in Wum Local Government, Southern (West) Cameroons, 1957 – 1968, Abstract. TP Mbeum. Vol 9 (2009), Post-Emancipation Slave Commerce: Increasing Child Slave Trafficking and Women's Agency in Late Nineteenth-century Ghana ...

  4. Browse Title Index

    African Journals Online (AJOL)

    Items 451 - 500 of 581 ... Issue, Title. Vol 30, No 1 (2016), Risky sexual behaviour and associated factors among students of Debre Tabor University, Northwest Ethiopia: a cross-sectional study, Abstract PDF. Awoke Derbie, Mekonnen Assefa, Daniel Mekonnen, Fantahun Biadglegne. Vol 28, No 1 (2014), Road traffic accident: ...

  5. Browse Title Index

    African Journals Online (AJOL)

    Items 451 - 500 of 1346 ... Issue, Title. Vol 32, No 1 (2015), Fire and the dynamics of two unpalatable grass species (Cymbopogon pospischilii and Elionurus muticus) in a semi-arid climate, Abstract. Hennie A Snyman. Vol 8, No 1 (1973), Fire as a method of controlling macchia (Fynos) vegetation on the Amathole Mountains of ...

  6. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 43, No 2 (2006), Review: "'n Wonderlike geweld. Jeugherinneringe", By Elsa Joubert (2005), Abstract PDF. Henriette Roos. Vol 53, No 1 (2016), Review: Breyten Breytenbach, A Monologue in Two Voices, Abstract PDF. Andy Carolin. Vol 53, No 1 (2016), Review: The Shadow of the Hummingbird, Abstract ...

  7. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 103 ... Issue, Title ... SE Edusah, E Osei-Tutu ... Vol 6, No 2 (2016), Interrelationships among unemployment, inflation and economic growth in Nigeria, Abstract .... Vol 4, No 3 (2014): Special Edition, Socio-cultural Issues for ...

  8. Browse Title Index

    African Journals Online (AJOL)

    Items 4351 - 4386 of 4386 ... Issue, Title. Vol 107, No 6 (2017), When students become patients: TB disease among medical undergraduates in Cape Town, South Africa, Abstract PDF. H van der Westhuizen, A Dramowski. Vol 106, No 4 (2016), Where do children die and what are the causes? Under-5 deaths in the Metro West ...

  9. Browse Title Index

    African Journals Online (AJOL)

    Issue, Title. Vol 10, No 2 (2014), Sorindeia warneckei Engl. (Anacardiaceae), une espèce multi-usagère de la dépression de la Lama au Togo, Abstract PDF. A Akodewou, S Akpavi, M Dourma, K Batawila, KB Amegnaglo, W Atakpama, K Akpagama. Vol 10, No 1 (2014), Sterculia setigera Del.: influence de quelques ...

  10. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 126 ... Issue, Title. Vol 8, No 2 (2016), 2010 FIFA World Cup stadium investment: Does the post-event usage justify the expenditure? Abstract PDF. Luke Humphrey, Gavin Fraser. Vol 6, No 1 (2014), 7Implication of mergers and acquisitions on stock returns before and during the 2007–2009 credit crunch: An ...

  11. A Study of HTML Title Tag Creation Behavior of Academic Web Sites

    Science.gov (United States)

    Noruzi, Alireza

    2007-01-01

    The HTML title tag information should identify and describe exactly what a Web page contains. This paper analyzes the "Title element" and raises a significant question: "Why is the title tag important?" Search engines base search results and page rankings on certain criteria. Among the most important criteria is the presence of the search keywords…

  12. INIS: Authority list for journal titles

    International Nuclear Information System (INIS)

    2008-01-01

    This is the 34th revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13 538 journal titles, 2 106 regularly scanned journals and 613 key journals. It was last updated in February 2008. A journal - or periodical - is a continuing publication issued in a succession of discrete parts, usually bearing numbering and/or chronological designations and intended to be continued indefinitely. It is generally published within a defined, fixed interval between issues and normally appears more than once per year. It includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as the Annual Review of Nuclear Science are included, but series titles such as the McGraw-Hill Series in Nuclear Engineering are not. The purpose of this document is to provide descriptive cataloguers with standard elements to include in bibliographic level 'S' of the INIS record. These elements include field (tag) 229 (Full Journal Title), 320 (ISSN) and 321 (CODEN). The full journal title is mandatory, and either the ISSN or the CODEN must be included (both may appear). Instructions on how to use this and other elements of the INIS record format are found in INIS: Guide to Bibliographic Description (IAEA-INIS-1). In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: - In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. - In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. - In Part III, all journals that are regularly scanned by

  13. INIS: Authority list for journal titles

    International Nuclear Information System (INIS)

    2009-01-01

    This is the 35th revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13 750 journal titles, 1 965 regularly scanned journals and 593 key journals. It was last updated in March 2009. A journal - or periodical - is a continuing publication issued in a succession of discrete parts, usually bearing numbering and/or chronological designations and intended to be continued indefinitely. It is generally published within a defined, fixed interval between issues and normally appears more than once per year. It includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as the Annual Review of Nuclear Science are included, but series titles such as the McGraw-Hill Series in Nuclear Engineering are not. The purpose of this document is to provide descriptive cataloguers with standard elements to include in bibliographic level 'S' of the INIS record. These elements include field (tag) 229 (Full Journal Title), 320 (ISSN) and 321 (CODEN). The full journal title is mandatory, and either the ISSN or the CODEN must be included (both may appear). Instructions on how to use this and other elements of the INIS record format are found in INIS: Guide to Bibliographic Description (IAEA-INIS-1). In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: - In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. - In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. - In Part III, all journals that are regularly scanned by the

  14. INIS: Authority list for journal titles

    International Nuclear Information System (INIS)

    2007-01-01

    This is the 33rd revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13 396 journal titles, 2 170 regularly scanned journals and 578 key journals. It was last updated in February 2007. A journal - or periodical - is a continuing publication issued in a succession of discrete parts, usually bearing numbering and/or chronological designations and intended to be continued indefinitely. It is generally published within a defined, fixed interval between issues and normally appears more than once per year. It includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as the Annual Review of Nuclear Science are included, but series titles such as the McGraw-Hill Series in Nuclear Engineering are not. The purpose of this document is to provide descriptive cataloguers with standard elements to include in bibliographic level 'S' of the INIS record. These elements include field (tag) 229 (Full Journal Title), 320 (ISSN) and 321 (CODEN). The full journal title is mandatory, and either the ISSN or the CODEN must be included (both may appear). Instructions on how to use this and other elements of the INIS record format are found in INIS: Guide to Bibliographic Description (IAEA-INIS-1). In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: - In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. - In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. - In Part III, all journals that are regularly scanned by

  15. A Study of Second-Year Engineering Students' Alternative Conceptions about Electric Potential, Current Intensity and Ohm's Law

    Science.gov (United States)

    Periago, M. Cristina; Bohigas, Xavier

    2005-01-01

    The aim of this research was to evaluate and analyse second-year industrial engineering and chemical engineering students prior knowledge of conceptual aspects of "circuit theory". Specifically, we focused on the basic concepts of electric potential and current intensity and on the fundamental relationship between them as expressed by Ohm's law.…

  16. Comparing in Cylinder Pressure Modelling of a DI Diesel Engine Fuelled on Alternative Fuel Using Two Tabulated Chemistry Approaches.

    Science.gov (United States)

    Ngayihi Abbe, Claude Valery; Nzengwa, Robert; Danwe, Raidandi

    2014-01-01

    The present work presents the comparative simulation of a diesel engine fuelled on diesel fuel and biodiesel fuel. Two models, based on tabulated chemistry, were implemented for the simulation purpose and results were compared with experimental data obtained from a single cylinder diesel engine. The first model is a single zone model based on the Krieger and Bormann combustion model while the second model is a two-zone model based on Olikara and Bormann combustion model. It was shown that both models can predict well the engine's in-cylinder pressure as well as its overall performances. The second model showed a better accuracy than the first, while the first model was easier to implement and faster to compute. It was found that the first method was better suited for real time engine control and monitoring while the second one was better suited for engine design and emission prediction.

  17. Integrating enzyme immobilization and protein engineering: An alternative path for the development of novel and improved industrial biocatalysts.

    Science.gov (United States)

    Bernal, Claudia; Rodríguez, Karen; Martínez, Ronny

    2018-06-09

    Enzyme immobilization often achieves reusable biocatalysts with improved operational stability and solvent resistance. However, these modifications are generally associated with a decrease in activity or detrimental modifications in catalytic properties. On the other hand, protein engineering aims to generate enzymes with increased performance at specific conditions by means of genetic manipulation, directed evolution and rational design. However, the achieved biocatalysts are generally generated as soluble enzymes, -thus not reusable- and their performance under real operational conditions is uncertain. Combined protein engineering and enzyme immobilization approaches have been employed as parallel or consecutive strategies for improving an enzyme of interest. Recent reports show efforts on simultaneously improving both enzymatic and immobilization components through genetic modification of enzymes and optimizing binding chemistry for site-specific and oriented immobilization. Nonetheless, enzyme engineering and immobilization are usually performed as separate workflows to achieve improved biocatalysts. In this review, we summarize and discuss recent research aiming to integrate enzyme immobilization and protein engineering and propose strategies to further converge protein engineering and enzyme immobilization efforts into a novel "immobilized biocatalyst engineering" research field. We believe that through the integration of both enzyme engineering and enzyme immobilization strategies, novel biocatalysts can be obtained, not only as the sum of independently improved intrinsic and operational properties of enzymes, but ultimately tailored specifically for increased performance as immobilized biocatalysts, potentially paving the way for a qualitative jump in the development of efficient, stable biocatalysts with greater real-world potential in challenging bioprocess applications. Copyright © 2018. Published by Elsevier Inc.

  18. Polymer reaction engineering, an integrated approach

    NARCIS (Netherlands)

    Meyer, T.; Keurentjes, J.T.F.; Meyer, T.; Keurentjes, J.T.F.

    2005-01-01

    Summary This chapter contains sections titled: Polymer Materials A Short History of Polymer Reaction Engineering The Position of Polymer Reaction Engineering Toward Integrated Polymer Reaction Engineering The Disciplines in Polymer Reaction Engineering The Future: Product-inspired Polymer Reaction

  19. Producer gas production of Indonesian biomass in fixed-bed downdraft gasifier as an alternative fuels for internal combustion engines

    Science.gov (United States)

    Simanjuntak, J. P.; Lisyanto; Daryanto, E.; Tambunan, B. H.

    2018-03-01

    downdraft biomass gasification reactors, coupled with reciprocating internal combustion engines (ICE) are a viable technology for small scale heat and power generation. The direct use of producer gas as fuel subtitution in an ICE could be of great interest since Indonesia has significant land area in different forest types that could be used to produce bioenergy and convert forest materials to bioenergy for use in energy production and the versatility of this engine. This paper will look into the aspect of biomass energie as a contributor to energy mix in Indonesia. This work also contains information gathered from numerous previews study on the downdraft gasifier based on experimental or simulation study on the ability of producer gas as fuels for internal combustion engines aplication. All data will be used to complement the preliminary work on biomass gasification using downdraft to produce producer gas and its application to engines.

  20. Reformulated Neural Network (ReNN): a New Alternative for Data-driven Modelling in Hydrology and Water Resources Engineering

    Science.gov (United States)

    Razavi, S.; Tolson, B.; Burn, D.; Seglenieks, F.

    2012-04-01

    Reformulated Neural Network (ReNN) has been recently developed as an efficient and more effective alternative to feedforward multi-layer perceptron (MLP) neural networks [Razavi, S., and Tolson, B. A. (2011). "A new formulation for feedforward neural networks." IEEE Transactions on Neural Networks, 22(10), 1588-1598, DOI: 1510.1109/TNN.2011.2163169]. This presentation initially aims to introduce the ReNN to the water resources community and then demonstrates ReNN applications to water resources related problems. ReNN is essentially equivalent to a single-hidden-layer MLP neural network but defined on a new set of network variables which is more effective than the traditional set of network weights and biases. The main features of the new network variables are that they are geometrically interpretable and each variable has a distinct role in forming the network response. ReNN is more efficiently trained as it has a less complex error response surface. In addition to the ReNN training efficiency, the interpretability of the ReNN variables enables the users to monitor and understand the internal behaviour of the network while training. Regularization in the ReNN response can be also directly measured and controlled. This feature improves the generalization ability of the network. The appeal of the ReNN is demonstrated with two ReNN applications to water resources engineering problems. In the first application, the ReNN is used to model the rainfall-runoff relationships in multiple watersheds in the Great Lakes basin located in northeastern North America. Modelling inflows to the Great Lakes are of great importance to the management of the Great Lakes system. Due to the lack of some detailed physical data about existing control structures in many subwatersheds of this huge basin, the data-driven approach to modelling such as the ReNN are required to replace predictions from a physically-based rainfall runoff model. Unlike traditional MLPs, the ReNN does not necessarily

  1. Biodiesel production from inedible animal tallow and an experimental investigation of its use as alternative fuel in a direct injection diesel engine

    International Nuclear Information System (INIS)

    Oener, Cengiz; Altun, Sehmus

    2009-01-01

    In this study, a substitute fuel for diesel engines was produced from inedible animal tallow and its usability was investigated as pure biodiesel and its blends with petroleum diesel fuel in a diesel engine. Tallow methyl ester as biodiesel fuel was prepared by base-catalyzed transesterification of the fat with methanol in the presence of NaOH as catalyst. Fuel properties of methyl ester, diesel fuel and blends of them (5%, 20% and 50% by volume) were determined. Viscosity and density of fatty acid methyl ester have been found to meet ASTM D6751 and EN 14214 specifications. Viscosity and density of tallow methyl esters are found to be very close to that of diesel. The calorific value of biodiesel is found to be slightly lower than that of diesel. An experimental study was carried out in order to investigate of its usability as alternative fuel of tallow methyl ester in a direct injection diesel engine. It was observed that the addition of biodiesel to the diesel fuel decreases the effective efficiency of engine and increases the specific fuel consumption. This is due to the lower heating value of biodiesel compared to diesel fuel. However, the effective engine power was comparable by biodiesel compared with diesel fuel. Emissions of carbon monoxide (CO), oxides of nitrogen (NO x ), sulphur dioxide (SO 2 ) and smoke opacity were reduced around 15%, 38.5%, 72.7% and 56.8%, respectively, in case of tallow methyl esters (B100) compared to diesel fuel. Besides, the lowest CO, NO x emissions and the highest exhaust temperature were obtained for B20 among all other fuels. The reductions in exhaust emissions made tallow methyl esters and its blends, especially B20 a suitable alternative fuel for diesel and thus could help in controlling air pollution. Based on this study, animal tallow methyl esters and its blends with petroleum diesel fuel can be used a substitute for diesel in direct injection diesel engines without any engine modification. (author)

  2. Microstructure and Engineering Properties of Alkali Activated Fly Ash -as an environment friendly alternative to Portland cement

    NARCIS (Netherlands)

    Ma, Y.

    2013-01-01

    Alkali activated fly ash (AAFA), also named “geopolymer”, has emerged as a novel engineering material in the construction industry. This material is normally formed by the reaction between fly ash and aqueous hydroxide or alkali silicate solution. With proper mix design, AAFA can present comparable

  3. Elevating Learner Achievement Using Formative Electronic Lab Assessments in the Engineering Laboratory: A Viable Alternative to Weekly Lab Reports

    Science.gov (United States)

    Chen, Baiyun; DeMara, Ronald F.; Salehi, Soheil; Hartshorne, Richard

    2018-01-01

    A laboratory pedagogy interweaving weekly student portfolios with onsite formative electronic laboratory assessments (ELAs) is developed and assessed within the laboratory component of a required core course of the electrical and computer engineering (ECE) undergraduate curriculum. The approach acts to promote student outcomes, and neutralize…

  4. Emulation-Based Virtual Laboratories: A Low-Cost Alternative to Physical Experiments in Control Engineering Education

    Science.gov (United States)

    Goodwin, G. C.; Medioli, A. M.; Sher, W.; Vlacic, L. B.; Welsh, J. S.

    2011-01-01

    This paper argues the case for emulation-based virtual laboratories in control engineering education. It demonstrates that such emulation experiments can give students an industrially relevant educational experience at relatively low cost. The paper also describes a particular emulation-based system that has been developed with the aim of giving…

  5. Quantitative Framework to Evaluate Alternative Dispute Resolution Investments in Architecture Engineering and Construction Projects Using Option and Real Option Theory

    Science.gov (United States)

    Menassa, Carol Chukri

    2009-01-01

    A project-specific dispute resolution ladder (DRL) typically consists of multiple alternative dispute resolution (ADR) techniques that are chosen to assist in mitigating the impact of change orders and claims (CCO) occurring during the project construction phase, and avoid their escalation to protracted disputes that adversely affect a…

  6. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 546 ... Vol 9, No 1 (2011), Application of Field programmable Gate Array to ... Vol 5, No 1 (2007), Barriers To Choice Of Women Occupation In ... Road Transport – Study Of Gibraltar Engineering Company, Aba, Nigeria, Abstract.

  7. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 879 ... South African Journal of Higher Education. ... Vol 15, No 3 (2001), A four quadrant whole brain approach in innovation and engineering ... for measuring the quality of student learning in outcomes-based education, Abstract.

  8. Browse Title Index

    African Journals Online (AJOL)

    Items 201 - 241 of 241 ... Zimbabwe Journal of Educational Research. ... Vol 27, No 3 (2015), The Importance of Play in Early Childhood Development: ... of Science Technology Engineering and Mathematics (STEM) Education in Zimbabwe ...

  9. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 34 of 34 ... Journal of Modeling, Design and Management of Engineering Systems. ... to Determine The Critical Time-Step in Discrete Element Modelling, Abstract ... ELEMENT MODELLING OF THE COMPRESSIVE LOADING OF BULK ...

  10. Browse Title Index

    African Journals Online (AJOL)

    Items 751 - 800 of 1199 ... Vol 2, No 4 (2008): Special Edition - Engineering, Practical ... Analysis of the Factors of Socio- Economic Development of Nigeria - A Case Study ... and Communication Technology for Solving Work Place Problems and ...

  11. Browse Title Index

    African Journals Online (AJOL)

    Items 801 - 850 of 1255 ... Vol 8, No 4 (2002), Model of predicting proportion of diesel fuel and engine oil in diesel adulterated SAE 40 engine oil sample, Abstract PDF. S.E. Etuk, L.E. Akpabio, S.D. Ekpe. Vol 11, No 1 (2005), Modeling 3D Unknown object by Range Finder and Video Camera and Updating of a 3D Database by ...

  12. Browse Title Index

    African Journals Online (AJOL)

    Items 301 - 350 of 421 ... Vol 9, No 1 (2011), Relationship between gender and university students' academic ... Vol 2, No 1 (2004), Research Alternative for Nursing Practice: A .... in relation to self-esteem of university business students, Abstract.

  13. Browse Title Index

    African Journals Online (AJOL)

    Items 801 - 850 of 2157 ... South African Journal of Animal Science. ... and growth in Bonsmara bulls and evaluation of alternative measures of feed efficiency, Abstract PDF ... Vol 41, No 2 (2011), Evaluation of dehulled faba bean (Vicia faba cv.

  14. Determination of the Quantitative Characteristics of the Engine of a Household Power Plant when Using Generator Gas as an Alternative Fuel

    Directory of Open Access Journals (Sweden)

    Plotnikov S. A.

    2017-08-01

    Full Text Available The relevance of the study is due to the need to study the feasibility of replacing traditional fuel with alternative types (generator gas when using a household power plant. The purpose of the study is to obtain the value of a small-displacement engine GG-2700 with a working volume of 1563 cm3 when it works on commercial fuel (gasoline and generator gas. For this purpose, the authors developed an experimental setup on the basis of a small-sized household power station with fixation of variable parameters on a personal computer and a graphical representation of the measurement results. The records of the indicator diagrams allowed determining the burning time of various fuels. As a result, for the first time, there were obtained quantitative indicators of fuel efficiency and toxicity of exhaust gases of the small-displacement engine GG-2700 with a working volume of 1563 cm3 when using commercial fuel (gasoline and generator gas. The analysis of the data showed an increase in the specific consumption of generator gas in comparison with gasoline from 34.6% to 50.4% and a decrease in the content of toxic components in the exhaust gases: carbon monoxide (CO – in 1.05 ... 1.25 times, hydrocarbons (CxHy - in 1,1 ... 1,39 times, nitrogen oxides (NOх - in 3,9 ... 5,7 times. The obtained results prove the expediency of using generator gas as an alternative fuel for the engine of a household power plant.

  15. Biodiesel from vegetable oil as alternate fuel for C.I engine and feasibility study of thermal cracking: A critical review

    International Nuclear Information System (INIS)

    Ramkumar, S.; Kirubakaran, V.

    2016-01-01

    Highlights: • The C.V of biodiesel is less than diesel of about 10% on volume and 15% on mass basis. • Most forms of biodiesel and its blends with diesel have higher viscosity than diesel. • Biodiesel’s cost and by-product reduce its feasibility as a substitute fuel. • TGA & DCS of Pungamia Oil shows that Thermal cracking is an alternate to Biodiesel. - Abstract: The awareness about using eco friendly fuels like biodiesel is increasing every day. The Increase in global warming and energy crises due to fossil fuel has accelerated the search of bio fuels. Biodiesel is a promising fuel; it is available in a wide range in every part of the world. Most of the studies reveal that the performance of biodiesel is better than that of diesel. Except NOx, the major emissions are high in the case of fossil fuels. This paper reviews the performance and emission characteristics of biodiesel in C.I engines. The paper also reviews the influence of engine modifications, various additives, and various proportions of blends of biodiesel with diesel. The physical and thermal characteristics of biodiesel have a great influence in the performance and emission, and they are tabulated in this paper. This paper also attempts feasibility of admitting vegetable oil in IC engine through Thermal Cracking. Preliminary investigation shows encouraging results and reported in this paper.

  16. Alternative inerting agents

    CSIR Research Space (South Africa)

    Du

    1997-08-01

    Full Text Available Final Project Report ALTERNATIVE INERTING AGENTS Author/s: J J L DU PLESSIS Research Agency: OSIR MINING TECHNOLOGY Project No: Date: 3 2 7 2 COL 443 APRIL 1999 N’ ) ( G~6~ I Title: 9 / The results show...

  17. Providing engineering services to counties.

    Science.gov (United States)

    2008-09-01

    An engineer is required by law to safeguard the health, safety and welfare of the public. The current Kansas : statute state, The Board of County Commissioners of each county shall appoint a licensed professional : engineer, whose title shall be c...

  18. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 161 ... Global Journal of Engineering Research. ... Vol 2, No 1 (2003), Investigation of the potentials of Nigerian salt deposit as fluxing materials in secondary aluminium ... Vol 2, No 1 (2003), Motion and time study analysis of wooden locally ... Vol 15, No 1 (2016), Software for natural gas pipeline design and ...

  19. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 102 ... Journal of Civil Engineering Research and Practice. ... Economy: The Case of Inter-Regional Traffic Flow in the Lake Victoria Basin, ... Vol 7, No 1 (2010), Application of GIS-Based Spatially Distributed Hydrologic Model in ...

  20. Browse Title Index

    African Journals Online (AJOL)

    Items 51 - 100 of 465 ... AE Aghaji, FO Ugwumba. Vol 1, No 1 (1996), Bacteriology of wound infections in the surgical wards of a Teaching Hospital, Abstract. UC Ozumba, BC Ozumba. Vol 9, No 1 (2004), Biomedical Engineering and its Relevance to Total Health Care Delivery in Developing Countries, Abstract. GC Okoye.

  1. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 189 ... Vol 6, No 1 (2005), A low cost field usable portable digital grain moisture meter with direct display of moisture (%), Abstract PDF. R Rai, K Sivadasan, S.N Murty. Vol 5, No ... Vol 1, No 4 (2001), Analysis of NOx reduction in diesel engines by air injection using stochastic, Abstract PDF. ISN Mkilaha, GR John.

  2. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 97 ... Vol 25, No 1 (2013), A study of ergonomic factors leading to ... handling as risk factors for low back pain in delivery drivers, Abstract ... Vol 26, No 2 (2014), Changes in users' mental models of Web search engines after ten ...

  3. Browse Title Index

    African Journals Online (AJOL)

    Items 5901 - 5950 of 11090 ... Vol 8, No 13 (2009), High-density fermentation and functional ... to D-lactic acid with metabolically engineered Escherichia coli, Abstract PDF ... by Aspergillus candidus URM 5611 under solid state fermentation ... Vol 12, No 21 (2013), Histamine and tyramine production by bacteria isolated from ...

  4. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 243 ... Vol 20 (2011): Series C: Mathematical Sciences, Engineering and Technology, Monthly Wind Characteristics and Wind Energy in Rwanda, Abstract PDF. B Sarari, J Gasore. Vol 1, No 1 (2016): Special Issue: Series D, Morphological and photometric properties of active and non-active galaxies in the ...

  5. Browse Title Index

    African Journals Online (AJOL)

    Items 151 - 200 of 591 ... Vol 8, No 1 (2010), Economic assessment of marketing and ... A. Gray used as green manure on the early growth of Parkia ... Vol 12, No 2 (2014), Effect of alternative hormones on the .... AJOL African Journals Online.

  6. Browse Title Index

    African Journals Online (AJOL)

    Items 251 - 300 of 522 ... Vol 21, No 1 (2015), Herbal and alternative medicine: the impact on anesthesia, Abstract PDF. JM Dippenaar. Vol 9, No 1 (2003), Herbal medications - harmless or harmful? Abstract PDF. SJB Johnston. Vol 21, No 1 (2015), How safe are regional techniques? Evidence from large studies with big data ...

  7. Browse Title Index

    African Journals Online (AJOL)

    Vol 14, No 3 (2017), Survey of dental students' attitude regarding oriental medicine/complementary and alternative medicine: comparison between two Japanese dental schools, Abstract PDF. Atsushi Kameyama, Kazuo Toda. Vol 13, No 4 (2016), Sustainable development of Amomum villosum: A systematic investigation ...

  8. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 167 ... Vol 1, No 1 (2010), Agricultural Marketing Cooperatives in Developing Society in Relation to Poverty Alleviation and Sustainable Development: The Case of Lesotho, Abstract. MMM Daemane, KA Mot'soene, VZ Nyawo-Shava. Vol 8, No 1 (2017), An alternative approach to financing development in Africa ...

  9. Browse Title Index

    African Journals Online (AJOL)

    Items 951 - 1000 of 1710 ... C Grover, N Goel, C Armour, PP Van Asperen, SN Gaur, RJ Moles, B Saini. Vol 14, No 4 (2011), Melkerssons-Rosenthal syndrome: A case report and review of the literature, Abstract PDF. OA Talabi. Vol 17, No 6 (2014), Mental disorders frequency alternative and complementary medicine usage ...

  10. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 273 ... Vol 38, No 3 (2012), Biorecognition Ability of Polysaccharides as Piezo Quartz Biosensors, Abstract PDF. EN Kalmykova, CA Mgina. Vol 27, No 1 (2001), Cashew nut shell liquid as an alternative corrosion inhibitor for carbon steels. Abstract PDF. JYN Philip, J Buchweishaija, LL Mkayula. Vol 30 (2004): ...

  11. Browse Title Index

    African Journals Online (AJOL)

    Vol 3, No 8 (2004), Use of palm oil in the diet of the African mudfish, Clarias gariepinus ... Vol 13, No 16 (2014), Use of plumules cryopreservation to save coconut ... Vol 7, No 8 (2008), Use of psyllium (isubgol) husk as an alternative gelling ...

  12. Browse Title Index

    African Journals Online (AJOL)

    Items 1 - 50 of 1117 ... African Journal for Physical, Health Education, Recreation and Dance. ... Vol 20, No 2 (2014): Part 2, Comparative study of physical activity patterns ... Vol 20, No 2 (2014): Part 2, The use of mobile phone technology as an ... as an alternative to socio-economic development in Rwanda, Africa, Abstract.

  13. Browse Title Index

    African Journals Online (AJOL)

    Items 101 - 150 of 158 ... U Noma, R Ali, R Kane, M Donnelly. Vol 7, No 1 (2015), Propeller Flap for Complex Distal Leg Reconstruction: A Versatile Alternative when Reverse Sural Artery Flap is Not Feasible, Abstract PDF. Samuel A. Ademola, Afieharo I. Michael, Femi J. Oladeji, Kefas M. Mbaya, O. Oyewole. Vol 5, No 2 (2013) ...

  14. Developmental problems and their solution for the Space Shuttle main engine alternate liquid oxygen high-pressure turbopump: Anomaly or failure investigation the key

    Science.gov (United States)

    Ryan, R.; Gross, L. A.

    1995-05-01

    The Space Shuttle main engine (SSME) alternate high-pressure liquid oxygen pump experienced synchronous vibration and ball bearing life problems that were program threatening. The success of the program hinged on the ability to solve these development problems. The design and solutions to these problems are engirded in the lessons learned and experiences from prior programs, technology programs, and the ability to properly conduct failure or anomaly investigations. The failure investigation determines the problem cause and is the basis for recommending design solutions. For a complex problem, a comprehensive solution requires that formal investigation procedures be used, including fault trees, resolution logic, and action items worked through a concurrent engineering-multidiscipline team. The normal tendency to use an intuitive, cut-and-try approach will usually prove to be costly, both in money and time and will reach a less than optimum, poorly understood answer. The SSME alternate high-pressure oxidizer turbopump development has had two complex problems critical to program success: (1) high synchronous vibrations and (2) excessive ball bearing wear. This paper will use these two problems as examples of this formal failure investigation approach. The results of the team's investigation provides insight into the complexity of the turbomachinery technical discipline interacting/sensitivities and the fine balance of competing investigations required to solve problems and guarantee program success. It is very important to the solution process that maximum use be made of the resources that both the contractor and Government can bring to the problem in a supporting and noncompeting way. There is no place for the not-invented-here attitude. The resources include, but are not limited to: (1) specially skilled professionals; (2) supporting technologies; (3) computational codes and capabilities; and (4) test and manufacturing facilities.

  15. Genetically Engineered Islets and Alternative Sources of Insulin-Producing Cells for Treating Autoimmune Diabetes: Quo Vadis?

    Directory of Open Access Journals (Sweden)

    Feng-Cheng Chou

    2012-01-01

    Full Text Available Islet transplantation is a promising therapy for patients with type 1 diabetes that can provide moment-to-moment metabolic control of glucose and allow them to achieve insulin independence. However, two major problems need to be overcome: (1 detrimental immune responses, including inflammation induced by the islet isolation/transplantation procedure, recurrence autoimmunity, and allorejection, can cause graft loss and (2 inadequate numbers of organ donors. Several gene therapy approaches and pharmaceutical treatments have been demonstrated to prolong the survival of pancreatic islet grafts in animal models; however, the clinical applications need to be investigated further. In addition, for an alternative source of pancreatic β-cell replacement therapy, the ex vivo generation of insulin-secreting cells from diverse origins of stem/progenitor cells has become an attractive option in regenerative medicine. This paper focuses on the genetic manipulation of islets during transplantation therapy and summarizes current strategies to obtain functional insulin-secreting cells from stem/progenitor cells.

  16. The flexible feedstock concept in Industrial Biotechnology: Metabolic engineering of Escherichia coli, Corynebacterium glutamicum, Pseudomonas, Bacillus and yeast strains for access to alternative carbon sources.

    Science.gov (United States)

    Wendisch, Volker F; Brito, Luciana Fernandes; Gil Lopez, Marina; Hennig, Guido; Pfeifenschneider, Johannes; Sgobba, Elvira; Veldmann, Kareen H

    2016-09-20

    Most biotechnological processes are based on glucose that is either present in molasses or generated from starch by enzymatic hydrolysis. At the very high, million-ton scale production volumes, for instance for fermentative production of the biofuel ethanol or of commodity chemicals such as organic acids and amino acids, competing uses of carbon sources e.g. in human and animal nutrition have to be taken into account. Thus, the biotechnological production hosts E. coli, C. glutamicum, pseudomonads, bacilli and Baker's yeast used in these large scale processes have been engineered for efficient utilization of alternative carbon sources. This flexible feedstock concept is central to the use of non-glucose second and third generation feedstocks in the emerging bioeconomy. The metabolic engineering efforts to broaden the substrate scope of E. coli, C. glutamicum, pseudomonads, B. subtilis and yeasts to include non-native carbon sources will be reviewed. Strategies to enable simultaneous consumption of mixtures of native and non-native carbon sources present in biomass hydrolysates will be summarized and a perspective on how to further increase feedstock flexibility for the realization of biorefinery processes will be given. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. A study on synthesis of energy fuel from waste plastic and assessment of its potential as an alternative fuel for diesel engines.

    Science.gov (United States)

    Kaimal, Viswanath K; Vijayabalan, P

    2016-05-01

    The demand for plastic is ever increasing and has produced a huge amount of plastic waste. The management and disposal of plastic waste have become a major concern, especially in developing cities. The idea of waste to energy recovery is one of the promising techniques used for managing the waste plastic. This paper assesses the potential of using Waste Plastic Oil (WPO), synthesized using pyrolysis of waste plastic, as an alternative for diesel fuel. In this research work, the performance and emission characteristics of a single cylinder diesel engine fuelled with WPO and its blends with diesel are studied. In addition to neat plastic oil, three blends (PO25, PO50 and PO75) were prepared on a volumetric basis and the engine was able to run on neat plastic oil. Brake thermal efficiency of blends was lower compared to diesel, but PO25 showed similar performance to that of diesel. The emissions were reduced considerably while using blends when compared to neat plastic oil. The smoke and NOX were reduced by 22% and 17.8% respectively for PO25 than that of plastic oil. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Heterogeneous engineered cartilage growth results from gradients of media-supplemented active TGF-β and is ameliorated by the alternative supplementation of latent TGF-β.

    Science.gov (United States)

    Albro, Michael B; Nims, Robert J; Durney, Krista M; Cigan, Alexander D; Shim, Jay J; Vunjak-Novakovic, Gordana; Hung, Clark T; Ateshian, Gerard A

    2016-01-01

    Transforming growth factor beta (TGF-β) has become one of the most widely utilized mediators of engineered cartilage growth. It is typically exogenously supplemented in the culture medium in its active form, with the expectation that it will readily transport into tissue constructs through passive diffusion and influence cellular biosynthesis uniformly. The results of this investigation advance three novel concepts regarding the role of TGF-β in cartilage tissue engineering that have important implications for tissue development. First, through the experimental and computational analysis of TGF-β concentration distributions, we demonstrate that, contrary to conventional expectations, media-supplemented exogenous active TGF-β exhibits a pronounced concentration gradient in tissue constructs, resulting from a combination of high-affinity binding interactions and a high cellular internalization rate. These gradients are sustained throughout the entire culture duration, leading to highly heterogeneous tissue growth; biochemical and histological measurements support that while biochemical content is enhanced up to 4-fold at the construct periphery, enhancements are entirely absent beyond 1 mm from the construct surface. Second, construct-encapsulated chondrocytes continuously secrete large amounts of endogenous TGF-β in its latent form, a portion of which undergoes cell-mediated activation and enhances biosynthesis uniformly throughout the tissue. Finally, motivated by these prior insights, we demonstrate that the alternative supplementation of additional exogenous latent TGF-β enhances biosynthesis uniformly throughout tissue constructs, leading to enhanced but homogeneous tissue growth. This novel demonstration suggests that latent TGF-β supplementation may be utilized as an important tool for the translational engineering of large cartilage constructs that will be required to repair the large osteoarthritic defects observed clinically. Copyright © 2015

  19. 32 CFR 644.62 - Title evidence.

    Science.gov (United States)

    2010-07-01

    ... HANDBOOK Acquisition Procurement of Title Evidence, Title Clearance, and Closings § 644.62 Title evidence... and their charter to issue the same. They must also be financially sound and be willing and able to...

  20. Region 7 Title V facilities

    Data.gov (United States)

    U.S. Environmental Protection Agency — This web map shows the Region 7 Title V facilities (Clean Air Act major sources), any Class I areas within 300 km of R7 States, and any Tribal areas within 50 miles...

  1. Title V Permitting Statistics Inventory

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Title V Permitting Statistics Inventory contains measured and estimated nationwide statistical data, consisting of counts of permitted sources, types of permits...

  2. Elmo Bumpy Torus proof of principle. Phase II - title 1 report. Volume I. Device summary

    International Nuclear Information System (INIS)

    Haas, D.W.

    1982-02-01

    This document presents a summary of the EBT-P Preliminary Design (Title I) effort. The work was performed, under the direction of ORNL, for the Department of Energy by MDAC-St. Louis. Major subcontractors assisting MDAC included General Dynamics for the magnet system, Gilbert Associates for the device utilities and facility architecture and engineering, and Lockheed - Oak Ridge for engineering support services. The Title I period of performance was from 1 October 1980 to 1 March 1982

  3. Sensitivity of the engineered barrier system (EBS) release rate to alternative conceptual models of advective release from waste packages under dripping fractures

    International Nuclear Information System (INIS)

    Lee, J.H.; Atkins, J.E.; McNeish, J.A.; Vallikat, V.

    1996-01-01

    Simulations were conducted to analyze the sensitivity of the engineered barrier system (EBS) release rate to alternative conceptual models of the advective release from waste packages under dripping fractures. The first conceptual model assumed that dripping water directly contacts the waste form inside the 'failed' waste package, and radionuclides are released from the EBS by advection. The second conceptual model assumed that dripping water is diverted around the 'failed' waste package (because of the presence of corrosion products plugging the perforations) and dripping water is prevented from directly contacting the waste form. In the second model, radionuclides were assumed to transport through the perforations by diffusion, and, once outside the waste package, to be released from the EBS by advection. The second model was to incorporate more realism into the EBS release calculations. For the case with the second EBS release model, most radionuclides had significantly lower peak EBS release rates (from at least one to several orders of magnitude) than with the first EBS release model. The impacts of the alternative EBS release models were greater for the radionuclides with a low solubility (or solubility-limited radionuclides) than for the radionuclides with a high solubility (or waste form dissolution-limited radionuclides). The analyses indicated that the EBS release model representing advection through a 'failed' waste package (the first EBS release model) may be too conservative in predicting the EBS performance. One major implication from this sensitivity study was that a 'failed' waste package container with multiple perforations may still be able to perform effectively as an important barrier to radionuclide release. (author)

  4. Liquid Rocket Engine Testing

    Science.gov (United States)

    2016-10-21

    Briefing Charts 3. DATES COVERED (From - To) 17 October 2016 – 26 October 2016 4. TITLE AND SUBTITLE Liquid Rocket Engine Testing 5a. CONTRACT NUMBER...298 (Rev. 8-98) Prescribed by ANSI Std. 239.18 Liquid Rocket Engine Testing SFTE Symposium 21 October 2016 Jake Robertson, Capt USAF AFRL...Distribution Unlimited. PA Clearance 16493 Liquid Rocket Engine Testing • Engines and their components are extensively static-tested in development • This

  5. National Ignition Facility Title II Design Plan

    International Nuclear Information System (INIS)

    Kumpan, S

    1997-01-01

    This National Ignition Facility (NIF) Title II Design Plan defines the work to be performed by the NIF Project Team between November 1996, when the U.S. Department of Energy (DOE) reviewed Title I design and authorized the initiation of Title H design and specific long-lead procurements, and September 1998, when Title 11 design will be completed

  6. The simulation of the alternate turbopump development high pressure oxygen and fuel turbopumps for the space shuttle main engine using the Shaberth computer program

    Science.gov (United States)

    Mcdonald, Gary H.

    1988-01-01

    The Space Shuttle Main Engine (SSME) is basically comprised of a combustion chamber and nozzle, high and low pressure oxygen turbopumps and high and low pressure fuel turbopumps. In the current configuration, the high pressure fuel (HPTFP) and high pressure oxygen turbopumps (HPOTP) have experienced a history of ball bearing wear. The wear problem can be attributed to numerous factors including the hydrodynamic axial and radial loads caused by the flow of liquid oxygen and liquid hydrogen through the turbopump impellers and turbine. Also, friction effects between the rolling elements, races, and cage can create thermally induced bearing geometry changes. To alleviate some of the current configuration problems, an alternate turbopump development (ATD) was proposed. However, the ATD HPOTP and HPTFP are constrained to operate interchangeably with the current turbopumps, thus, the operation conditions must be similar. The ATD configuration features a major change in bearings used to support the integrated shaft, impeller, and turbine system. A single ball and single roller will replace the pump-end and turbine and duplex ball bearings. The Shaft-Bearing-Thermal (SHABERTH) computer code was used to model the ATD HPOTP and ATD HPFTP configurations. A two bearing model was used to simulate the HPOTP and HPFTP bearings and shaft geometry. From SHABERTH, a comparison of bearing reaction loads, frictional heat generation rates, and Hertz contact stresses will be attempted with analysis at the 109 percent and 65 percent power levels.

  7. Engineering Evaluation of Proposed Alternative Salt Transfer Method for the Molten Salt Reactor Experiment for the Oak Ridge National Laboratory, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    Carlberg, Jon A.; Roberts, Kenneth T.; Kollie, Thomas G.; Little, Leslie E.; Brady, Sherman D.

    2009-01-01

    This evaluation was performed by Pro2Serve in accordance with the Technical Specification for an Engineering Evaluation of the Proposed Alternative Salt Transfer Method for the Molten Salt Reactor Experiment at the Oak Ridge National Laboratory (BJC 2009b). The evaluators reviewed the Engineering Evaluation Work Plan for Molten Salt Reactor Experiment Residual Salt Removal, Oak Ridge National Laboratory, Oak Ridge, Tennessee (DOE 2008). The Work Plan (DOE 2008) involves installing a salt transfer probe and new drain line into the Fuel Drain Tanks and Fuel Flush Tank and connecting them to the new salt transfer line at the drain tank cell shield. The probe is to be inserted through the tank ball valve and the molten salt to the bottom of the tank. The tank would then be pressurized through the Reactive Gas Removal System to force the salt into the salt canisters. The Evaluation Team reviewed the work plan, interviewed site personnel, reviewed numerous documents on the Molten Salt Reactor (Sects. 7 and 8), and inspected the probes planned to be used for the transfer. Based on several concerns identified during this review, the team recommends not proceeding with the salt transfer via the proposed alternate salt transfer method. The major concerns identified during this evaluation are: (1) Structural integrity of the tanks - The main concern is with the corrosion that occurred during the fluorination phase of the uranium removal process. This may also apply to the salt transfer line for the Fuel Flush Tank. Corrosion Associated with Fluorination in the Oak Ridge National Laboratory Fluoride Volatility Process (Litman 1961) shows that this problem is significant. (2) Continued generation of Fluorine - Although the generation of Fluorine will be at a lower rate than experienced before the uranium removal, it will continue to be generated. This needs to be taken into consideration regardless of what actions are taken with the salt. (3) More than one phase of material

  8. Alternatives for managing wastes from reactors and post-fission operations in the LWR fuel cycle. Volume 4. Alternatives for waste isolation and disposal

    International Nuclear Information System (INIS)

    1976-05-01

    Volume IV of the five-volume report contains information on alternatives for final storage and disposal of radioactive wastes. Section titles include: basic concepts for geologic isolation; geologic storage alternatives; geologic disposal alternatives; extraterrestrial disposal; and, transmutation

  9. Alternatives for managing wastes from reactors and post-fission operations in the LWR fuel cycle. Volume 4. Alternatives for waste isolation and disposal

    Energy Technology Data Exchange (ETDEWEB)

    1976-05-01

    Volume IV of the five-volume report contains information on alternatives for final storage and disposal of radioactive wastes. Section titles include: basic concepts for geologic isolation; geologic storage alternatives; geologic disposal alternatives; extraterrestrial disposal; and, transmutation. (JGB)

  10. Corrosion Engineering.

    Science.gov (United States)

    White, Charles V.

    A description is provided for a Corrosion and Corrosion Control course offered in the Continuing Engineering Education Program at the General Motors Institute (GMI). GMI is a small cooperative engineering school of approximately 2,000 students who alternate between six-week periods of academic study and six weeks of related work experience in…

  11. Environmental and other evaluations of alternatives for management of defense transuranic waste at the Idaho National Engineering Laboratory. Volume 1 of 2

    International Nuclear Information System (INIS)

    1982-04-01

    The US Department of Energy (DOE) is responsible for developing and implementing methods for the safe and environmentally acceptable disposal of radioactive wastes. In connection with this responsibility, the DOE is formulating a program for the long-term management of transuranic (TRU) waste buried and stored at the Idaho National Engineering Laboratory (INEL). This report has been prepared to document the results of environmental and other evaluations for three decisions that the DOE is considering: (1) the selection of a general method for the long-term management of the buried TRU waste; (2) the selection of a method for processing the stored waste and for processing the buried waste, if it is retrieved; (3) the selection of a location for the waste-processing facility. This document pertains only to the contact-handled TRU waste buried in pits and trenches and the contact-handled TRU waste held in aboveground storage at the INEL. A decision has previously been made on a method for the long-term management of the stored waste; it will be retrieved and shipped to the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico. The WIPP is also used in this report as a reference repository for evaluation purposes for the buried waste. This report is contained in two volumes. Volume I is arranged as follows: the summary is an overview of the analyses contained in this document. Section 1 is a statement of the underlying purpose and need to which the report is responding. Section 2 describes the alterntives. Section 3 describes the affected environment at the INEL and the WIPP sites. Section 4 analyzes the environmental effects of each alternative. The appendices in Volume II contain data and discussions supporting the material presented in Volume I

  12. TITLE

    Directory of Open Access Journals (Sweden)

    Nisha K. M

    2016-01-01

    Full Text Available The new millennium is seen as an epoch of entrepreneurship with entrepreneurs perceiving novel opportunities, organizing resources, undertaking risks to pursue their goals in establishing innovative ventures for scaling new horizons. Women entrepreneurs have the potency to confront numerous challenges, such as creating equity, equilibrium, ensuring sustainable and inclusive socio economic development in divergent economies, by seizing tremendous business opportunities in the contemporary commercial world. Kerala, the southern State of India, is experiencing an economic renovation through technological transformation and, in particular, through the growth of women oriented Micro, Small and Medium Enterprises (MSMEs. The study aims to; identify the growth trends of women’s entrepreneurship in the micro enterprises of Kerala; examine whether women’s entrepreneurial activities significantly vary across the form of women owned enterprises, type of organization and nature of activity; and also explore the prospects and challenges faced by women entrepreneurs through micro entrepreneurial activities. Research methodology involves the application of descriptive quantitative analysis on the secondary data primarily collected from the database of Directorate of Industries and District Industries Centre for a period of 7 years extending from 2007-08 to 2013-14. Findings reveal that MSMEs spawn better income distribution, by operating in heterogeneous areas of the economy with limited capital and creating more employment opportunities, thereby reducing poverty and inequalities. The trend analysis reflects an escalation in the number of enterprises, investments, profits and employment opportunities generated especially through micro enterprises of women. They play a crucial role in the economy in terms of creating self employment and generating employment opportunities for others. A paradigm shift is seen in the role of women’s entrepreneurship in terms of innovation, attitudes, leadership qualities, competitiveness, entrepreneurial skill and absorbing new entrants to the job market, empowering marginalized women.

  13. 24 CFR 202.12 - Title II.

    Science.gov (United States)

    2010-04-01

    ... INSTITUTIONS AND MORTGAGEES Title I and Title II Specific Requirements § 202.12 Title II. (a) Tiered pricing—(1... rate up to two percentage points under the mortgagee's customary lending practices must be based on... after accounting for the value of servicing rights generated by making the loan and other income to the...

  14. Title I conceptual design for Pit 6 landfill closure at Lawrence Livermore National Laboratory Site 300

    International Nuclear Information System (INIS)

    MacDonnell, B.A.; Obenauf, K.S.

    1996-08-01

    The objective of this design project is to evaluate and prepare design and construction documents for a closure cover cap for the Pit 6 Landfill located at Lawrence Livermore National Laboratory Site 300. This submittal constitutes the Title I Design (Conceptual Design) for the closure cover of the Pit 6 Landfill. A Title I Design is generally 30 percent of the design effort. Title H Design takes the design to 100 percent complete. Comments and edits to this Title I Design will be addressed in the Title II design submittal. Contents of this report are as follows: project background; design issues and engineering approach; design drawings; calculation packages; construction specifications outline; and construction quality assurance plan outline

  15. 42 CFR 476.86 - Correlation of Title XI functions with Title XVIII functions.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 4 2010-10-01 2010-10-01 false Correlation of Title XI functions with Title XVIII functions. 476.86 Section 476.86 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF...) Qio Review Functions § 476.86 Correlation of Title XI functions with Title XVIII functions. (a...

  16. Alternative security

    International Nuclear Information System (INIS)

    Weston, B.H.

    1990-01-01

    This book contains the following chapters: The Military and Alternative Security: New Missions for Stable Conventional Security; Technology and Alternative Security: A Cherished Myth Expires; Law and Alternative Security: Toward a Just World Peace; Politics and Alternative Security: Toward a More Democratic, Therefore More Peaceful, World; Economics and Alternative Security: Toward a Peacekeeping International Economy; Psychology and Alternative Security: Needs, Perceptions, and Misperceptions; Religion and Alternative Security: A Prophetic Vision; and Toward Post-Nuclear Global Security: An Overview

  17. Finding Federal Money for Children's Services: Financing Services for Children through Title XX and Other Programs. Manual 1.

    Science.gov (United States)

    Copeland, William C.

    This is the first manual of a 4-part series on how to find, obtain, contract for and manage Federal money for children's services. The first manual concentrates on ways to locate funds for new and existing programs. Emphasis is on Title XX of the Social Security Act, but attention is given also to alternative sources where Title XX funds are not…

  18. A/E/C Graphics Standard: Release 2.0 (formerly titled CAD Drafting Standard)

    Science.gov (United States)

    2015-08-01

    acronyms: • A/E/C – Architecture , Engineering, and Construction • BIM – Building Information Modeling • CAD – Computer-Aided Design • CIM – Civil...title GENERAL NOTES. General notes applicable to sheets for a particular discipline (e.g., architectural , electrical, mechanical) shall be located on...Filled fonts are used primarily for titles and on cover sheets. • Symbol font: This font should be used in cases where Greek symbols are

  19. INIS: Authority list for journal titles

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-03-01

    This is the twenty-ninth revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). It lists the titles of 12 990 journals which have contained articles within the scope of INIS. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the reader to find titles easily, the list is divided into two parts. In Part I, the full journal titles are grouped by country or international organization responsible for coverage and ordered alphabetically. In Part II, the full journal titles of all countries or international organizations are arranged alphabetically. The country name or the international organization name responsible for coverage of the journal title to INIS is entered in parentheses. Journal titles marked with an asterisk are regularly scanned by INIS. Titles that have been identified by INIS Centres as 'Key Journals' are marked with the hash sign.

  20. INIS: Authority list for journal titles

    International Nuclear Information System (INIS)

    2003-01-01

    This is the twenty-ninth revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). It lists the titles of 12 990 journals which have contained articles within the scope of INIS. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the reader to find titles easily, the list is divided into two parts. In Part I, the full journal titles are grouped by country or international organization responsible for coverage and ordered alphabetically. In Part II, the full journal titles of all countries or international organizations are arranged alphabetically. The country name or the international organization name responsible for coverage of the journal title to INIS is entered in parentheses. Journal titles marked with an asterisk are regularly scanned by INIS. Titles that have been identified by INIS Centres as 'Key Journals' are marked with the hash sign

  1. Alternative additives; Alternative additiver

    Energy Technology Data Exchange (ETDEWEB)

    2007-08-15

    In this project a number of industrial and agricultural waste products have been characterised and evaluated in terms of alkali-getter performance. The intended use is for biomass-fired power stations aiming at reducing corrosion or slagging related problems. The following products have been obtained, characterised and evaluated: 1) Brewery draff 2) Danish de-gassed manure 3) Paper sludge 4) Moulding sand 5) Spent bleaching earth 6) Anorthosite 7) Sand 8) Clay-sludge. Most of the above alternative additive candidates are deemed unsuitable due to insufficient chemical effect and/or expensive requirements for pre-treatment (such as drying and transportation). 3 products were selected for full-scale testing: de-gassed manure, spent bleaching earth and clay slugde. The full scale tests were undertaken at the biomass-fired power stations in Koege, Slagelse and Ensted. Spent bleaching earth (SBE) and clay sludge were the only tested additive candidates that had a proven ability to react with KCl, to thereby reduce Cl-concentrations in deposits, and reduce the deposit flux to superheater tubes. Their performance was shown to nearly as good as commercial additives. De-gassed manure, however, did not evaluate positively due to inhibiting effects of Ca in the manure. Furthermore, de-gassed manure has a high concentration of heavy metals, which imposes a financial burden with regard to proper disposal of the ash by-products. Clay-sludge is a wet clay slurring, and drying and transportation of this product entails substantial costs. Spent bleaching does not require much pre-treatment and is therefore the most promising alternative additive. On the other hand, bleaching earth contains residual plant oil which means that a range of legislation relating to waste combustion comes into play. Not least a waste combustion fee of 330 DKK/tonne. For all alternative (and commercial) additives disposal costs of the increase ash by-products represents a significant cost. This is

  2. Registry of Mineral and Petroleum Titles

    Energy Technology Data Exchange (ETDEWEB)

    Maclellan, I. M.; Kaizer, J. L.; McCulloch, P. D.; Ratcliffe, R.; Wenning, A. S. [Nova Scotia Dept. of Natural Resources, Halifax, NS (Canada)

    2000-07-01

    Activities of the Nova Scotia Registry of Mineral and Petroleum Titles are described, including statistical information about staking and mining activity in the province during 1999. In terms of activities, the Registry receives applications and issues licenses and leases for mineral and petroleum rights, receives statements of exploration expenditures and assessment reports that pertain to renewal of licenses and leases, maintains maps showing the disposition of lands under license or lease, and maintains a system of prospector registration. In addition, the Registry processes applications for underground gas storage rights and treasure trove rights and maintains a database of information concerning production and employment in Nova Scotia mines and quarries. At the end 1999 there were 230,660 hectares under exploration licence. Exploration expenditures, including engineering, economic and feasibility studies during 1999 totalled $4.2 million, mostly by junior mining companies searching for industrial mineral commodities. Mining activity during 1999 generated revenues of $340 million. Coal production dropped by 25 per cent, due mainly to the closure of the Phalen Mine. Gypsum production was up to 7.9 million tonnes; shipments of cement, barite and clay products also increased during 1999; salt production remained unchanged from 1998 with 842,000 tonnes. Production of construction aggregates totalled 10.6 million tonnes, down slightly from the year before. Mineral industry employment was roughly 2,500 persons, down by 24 per cent from 1998 levels, due primarily to the closure of the Phalen Mine.

  3. Land Titles and Rice Production in Vietnam

    DEFF Research Database (Denmark)

    Van Den Broeck, Katleen; Newman, Carol; Tarp, Finn

    In most of the empirical literature on land titling, the household is regarded as unitary, and land rights are found to have ambiguous effects on land allocation, investment and productivity. Using data from 12 provinces in Vietnam, we diversify land titles, and show in a household fixed effects...... analysis of plot level rice yields that land titles are indeed important. Only exclusively held titles have the expected positive effects, and the positive effect on yields is found in male headed households. Furthermore, a household level rice yield function reveals that exclusive user rights...... are inefficiency decreasing, while jointly held user rights have no efficiency effects. Finally, once the gender of the head of household is controlled for, exclusively held female titles have a greater positive effect on the efficiency of the household than that of male held titles...

  4. Engineering qualifications for competence

    International Nuclear Information System (INIS)

    Levy, J.C.

    1990-01-01

    The Engineering Council has a responsibility across all fields of engineering to set standards for those who are registered as Chartered Engineers, Incorporated Engineers or Engineering Technicians. These standards amount to a basic specification of professional competence to which must be added the features needed in each different branch of engineering, such as nuclear, and each particular occupation, such as quality assurance. This article describes The Engineering Council's general standards and includes a guide to the roles and responsibilities which should lie within the domain of those who are registered with the Council. The concluding section describes the title of European Engineer and its relationship to the European Community directive governing the movement of professionals across community frontiers. (author)

  5. 76 FR 48101 - Petition for Approval of Alternate; Odometer Disclosure Requirements

    Science.gov (United States)

    2011-08-08

    ... implement an electronic vehicle title transfer system, the State of Florida has petitioned for approval of... certificate of title for transfers of motor vehicles. With electronic titling there would not be a paper... proposed alternate disclosure requirements for vehicle transfers involving casual or private sales. NHTSA...

  6. 24 CFR 200.61 - Title.

    Science.gov (United States)

    2010-04-01

    ... Commissioner. (c) Endorsement of the credit instrument for insurance shall evidence the acceptability of title... GENERAL INTRODUCTION TO FHA PROGRAMS Requirements for Application, Commitment, and Endorsement Generally...

  7. Comparing the characteristics of highly cited titles and highly alted titles

    Energy Technology Data Exchange (ETDEWEB)

    Didegah, F.; Bowman, T.D.; Bowman, S.; Hartley, J.

    2016-07-01

    This study examines differences in the types of titles for articles that show high altmetric activity (highly alted articles) versus highly cited articles. This work expands on previous research on document titles in combination with a grounded theory approach to develop a codebook in which articles were manually coded based on 11 characteristics. The results show that there are differences and similarities in titles across many of the examined characteristics; highly cited titles and highly mentioned titles on Wikipedia have some similar characteristics such as they have the the highest percentage of substantive words; in addition, there are no or very few titles referencing outside or with humor/lightness on both platforms. Twitter and Facebook also showed some similarities having the highest percentage of humorous/light titles and lowest percentage of substantive words in their titles. (Author)

  8. Toward a Definition of the Engineering Method.

    Science.gov (United States)

    Koen, Billy V.

    1988-01-01

    Describes a preliminary definition of engineering method as well as a definition and examples of engineering heuristics. After discussing some alternative definitions of the engineering method, a simplified definition of the engineering method is suggested. (YP)

  9. Getting to one from title 10 + title 32 unity of effort in the homeland

    OpenAIRE

    Prosch, Caroline Ross.

    2011-01-01

    CHDS State/Local Approved for public release; distribution is unlimited This thesis bridges the knowledge gap between Title 10 Active Duty and Title 32 National Guard in order to breakdown cultural barriers and reach unity of effort for response operations in the homeland. Regrettably, a unified response was missing among Title 10 Active Duty and Title 32 National Guard members following Hurricane Katrina. Since then, initiatives based in doctrine, statutes and formal recommendations...

  10. Alternatives to Traditional Notation.

    Science.gov (United States)

    Gaare, Mark

    1997-01-01

    Provides a introduction and overview to alternative music notation systems. Describes guitar tablature, accordion tablature, klavarskribo (a keyboard notational system developed by Cornelius Pot, a Dutch engineer), and the digital piano roll. Briefly discusses the history of notation reform and current efforts. Includes examples from scores. (MJP)

  11. TWTF design alternates

    International Nuclear Information System (INIS)

    Ayers, A.L. Sr.

    1982-03-01

    The Transuranic Waste Treatment Facility (TWTF) will process transuranic (TRU) waste in retrievable storage at the Idaho National Engineering Laboratory (INEL). The costs for a TWTF concept using a slagging pyrolysis incinerator were excessive. Alternate concepts using a slow speed shredder, a rotary kiln incinerator, and concrete immobilization should result in significant cost reductions. These will be included in future TWTF considerations

  12. African Journals Online: All Titles

    African Journals Online (AJOL)

    African Journal of Applied Zoology and Environmental Biology View Journal ..... Global Approaches to Extension Practice: A Journal of Agricultural Extension View Journal ... International Journal of Engineering, Science and Technology View Journal ... Journal of Applied Chemistry and Agricultural Research View Journal ...

  13. How property title impacts urban consolidation

    DEFF Research Database (Denmark)

    Easthope, Hazel; Warnken, Jan; Sherry, Cathy

    2014-01-01

    Continuing urbanisation is triggering an increase in multi-titled housing internationally. This trend has given rise to a substantial research interest in the social consequences of higher density living. Little enquiry, however, has been directed to examining how property title subdivisions gene...

  14. 31 CFR 505.01 - Short title.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Short title. 505.01 Section 505.01 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE OF FOREIGN... CERTAIN MERCHANDISE BETWEEN FOREIGN COUNTRIES § 505.01 Short title. The regulations in this part may be...

  15. 33 CFR 401.1 - Short title.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Short title. 401.1 Section 401.1 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT CORPORATION, DEPARTMENT OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations § 401.1 Short title. These regulations may be cited as the...

  16. 18 CFR 415.1 - Short title.

    Science.gov (United States)

    2010-04-01

    ... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Short title. 415.1 Section 415.1 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS-FLOOD PLAIN REGULATIONS Generally § 415.1 Short title. This part shall be known...

  17. 25 CFR 151.13 - Title examination.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Title examination. 151.13 Section 151.13 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER LAND ACQUISITIONS § 151.13 Title examination. If the Secretary determines that he will approve a request for the acquisition of land from...

  18. Student Achievement in Title I Schools

    Science.gov (United States)

    Diaz, Abby T.

    2017-01-01

    This researcher seeks to answer the following question: How did two elementary Title I schools, identified as "high performing" on the first Smarter Balanced assessment, address elements of Maslow's hierarchy of needs when developing school-wide initiatives to enhance student achievement? Many students in Title I schools face barriers to…

  19. Land Titles and Rice Production in Vietnam

    DEFF Research Database (Denmark)

    Van Den Broeck, Katleen; Newman, Carol; Tarp, Finn

    analysis of plot level rice yields that land titles are indeed important. Only exclusively held titles have the expected positive effects, and the positive effect on yields is found in male headed households. Furthermore, a household level rice yield function reveals that exclusive user rights...

  20. 24 CFR 202.11 - Title I.

    Science.gov (United States)

    2010-04-01

    ... in 24 CFR 25.5. Civil money penalties may be imposed against Title I lenders and mortgagees pursuant... unacceptable risk to the Department; or (iv) Transfer of a Title I loan to a party that does not have a valid...

  1. Alternative Remedies

    Science.gov (United States)

    ... Home › Aging & Health A to Z › Alternative Remedies Font ... medical treatment prescribed by their healthcare provider. Using this type of alternative therapy along with traditional treatments is ...

  2. Alternative Fuels

    Science.gov (United States)

    Alternative fuels include gaseous fuels such as hydrogen, natural gas, and propane; alcohols such as ethanol, methanol, and butanol; vegetable and waste-derived oils; and electricity. Overview of alternative fuels is here.

  3. Alternating Hemiplegia

    Science.gov (United States)

    ... to the symptoms of the disorder. View Full Definition Treatment Drug therapy including verapamil may help to reduce the ... the more serious form of alternating hemiplegia × ... Definition Alternating hemiplegia is a rare neurological disorder that ...

  4. Comparative Analysis of Toxic Responses of Organic Extracts from Diesel and Selected Alternative Fuels Engine Emissions in Human Lung BEAS-2B Cells

    Czech Academy of Sciences Publication Activity Database

    Líbalová, Helena; Rössner ml., Pavel; Vrbová, Kristýna; Brzicová, Táňa; Sikorová, Jitka; Vojtíšek-Lom, M.; Beránek, V.; Kléma, J.; Cigánek, M.; Neča, J.; Pěnčíková, K.; Machala, M.; Topinka, Jan

    2016-01-01

    Roč. 17, č. 11 (2016), s. 1833 E-ISSN 1422-0067 R&D Projects: GA ČR(CZ) GA13-01438S; GA MŠk(CZ) LO1508; GA MŠk(CZ) LM2015073 Institutional support: RVO:68378041 Keywords : diesel * alternative fuel s * diesel exhaust particles Subject RIV: DN - Health Impact of the Environment Quality Impact factor: 3.226, year: 2016

  5. 24 CFR 203.385 - Types of satisfactory title evidence.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Types of satisfactory title... Title Waivers § 203.385 Types of satisfactory title evidence. The following types of title evidence shall be satisfactory to the Commissioner: (a) Fee or owner's title policy. A fee or owner's policy of...

  6. Quarterly title list for the period ending June 1980

    International Nuclear Information System (INIS)

    1980-01-01

    The title list contains: a) 17 titles and abstracts of laboratory reports, b) 36 titles of publications (32 with abstracts), c) 13 titles of articles submitted for publication (12 with abstracts), and d) 72 titles of lectures (52 with abstracts.) (GG) [de

  7. Solid Waste Operations Complex W-113, Detail Design Report (Title II). Volume 1: Title II design report

    International Nuclear Information System (INIS)

    1995-09-01

    The Solid Waste Retrieval Facility--Phase 1 (Project W113) will provide the infrastructure and the facility required to retrieve from Trench 04, Burial ground 4C, contact handled (CH) drums and boxes at a rate that supports all retrieved TRU waste batching, treatment, storage, and disposal plans. This includes (1) operations related equipment and facilities, viz., a weather enclosure for the trench, retrieval equipment, weighing, venting, obtaining gas samples, overpacking, NDE, NDA, shipment of waste and (2) operations support related facilities, viz., a general office building, a retrieval staff change facility, and infrastructure upgrades such as supply and routing of water, sewer, electrical power, fire protection, roads, and telecommunication. Title I design for the operations related equipment and facilities was performed by Raytheon/BNFL, and that for the operations support related facilities including infrastructure upgrade was performed by KEH. These two scopes were combined into an integrated W113 Title II scope that was performed by Raytheon/BNFL. Volume 1 provides a comprehensive narrative description of the proposed facility and systems, the basis for each of the systems design, and the engineering assessments that were performed to support the technical basis of the Title II design. The intent of the system description presented is to provide WHC an understanding of the facilities and equipment provided and the A/E's perspective on how these systems will operate

  8. How to Develop an Engineering Design Task

    Science.gov (United States)

    Dankenbring, Chelsey; Capobianco, Brenda M.; Eichinger, David

    2014-01-01

    In this article, the authors provide an overview of engineering and the engineering design process, and describe the steps they took to develop a fifth grade-level, standards-based engineering design task titled "Getting the Dirt on Decomposition." Their main goal was to focus more on modeling the discrete steps they took to create and…

  9. In search of ideology. Socio-cultural dimensions of Google and alternative search engines (ITA-manu:script 13-02)

    OpenAIRE

    Mager, Astrid

    2013-01-01

    Google has been blamed for its de facto monopolistic position on the search engine market, its exploitation of user data, its privacy violations, and, most recently, for possible collaborations with the US-American National Security Agency (NSA). However, blaming Google is not enough, as I suggest in this article. Rather than being ready-made, Google and its ‘algorithmic ideology’ are constantly negotiated in society. Drawing on my previous work I show how the ‘new spirit of capitalism’ gets ...

  10. Academic Success of Urban African American Elementary Students in Title I Schools

    Science.gov (United States)

    Anderson, James Sebastian

    2017-01-01

    The researcher investigated the achievement of third- and fifth-grade urban African American students who attended science, technology, engineering, and mathematics (STEM), Non-STEM, and Theme Title I schools in science and mathematics on the 2015 Georgia Milestones Assessment. The researcher used data from 29 Non-STEM, 14 STEM, and 10 Theme…

  11. Genetically engineered fusion of MAP-1 and factor H domains 1-5 generates a potent dual upstream inhibitor of both the lectin and alternative complement pathways

    DEFF Research Database (Denmark)

    Nordmaj, Mie Anemone; Munthe-Fog, Lea; Hein, Estrid

    2015-01-01

    Inhibition of the complement cascade has emerged as an option for treatment of a range of diseases. Mannose-binding lectin/ficolin/collectin-associated protein (MAP-1) is a pattern recognition molecule (PRM)-associated inhibitor of the lectin pathway. The central regulator of the alternative......:4 in a solid-phase functional assay, only the first 5 N-terminal domains of complement FH fused to the C-terminal part of full-length MAP-1 chimeric construct were able to combine inhibition of lectin and AP activation with an half maximal inhibitory concentration of ∼ 100 and 20 nM, respectively. No effect...

  12. INIS: Authority list for journal titles

    International Nuclear Information System (INIS)

    2005-01-01

    This is the 31st revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13,104 journal titles, 2,078 regularly scanned journals and 561 key journals. It was last updated in February 2005. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part III, all journals that are regularly scanned by INIS Centers are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part IV, all journals that are regularly scanned by INIS Centers are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part V, all journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part VI, all journals are sorted alphabetically under their title. The name of the

  13. INIS: Authority list for journal titles

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-03-01

    This is the 31st revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13,104 journal titles, 2,078 regularly scanned journals and 561 key journals. It was last updated in February 2005. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part III, all journals that are regularly scanned by INIS Centers are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part IV, all journals that are regularly scanned by INIS Centers are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part V, all journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part VI, all journals are sorted alphabetically under their title. The name of the

  14. INIS: Authority list for journal titles

    International Nuclear Information System (INIS)

    2006-01-01

    This is the 32nd revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13,231 journal titles, 2,125 regularly scanned journals and 555 key journals. It was last updated in February 2006. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part III, all journals that are regularly scanned by INIS Centres are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part IV, all journals that are regularly scanned by INIS Centres are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part V, all journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part VI, all journals are sorted alphabetically under their title. The name of the

  15. A Program on Biochemical and Biomedical Engineering.

    Science.gov (United States)

    San, Ka-Yiu; McIntire, Larry V.

    1989-01-01

    Presents an introduction to the Biochemical and Biomedical Engineering program at Rice University. Describes the development of the academic and enhancement programs, including organizational structure and research project titles. (YP)

  16. The SNS target station preliminary Title I shielding analyses

    International Nuclear Information System (INIS)

    Johnson, J.O.; Santoro, R.T.; Lillie, R.A.; Barnes, J.M.; McNeilly, G.S.

    2000-01-01

    The Department of Energy (DOE) has given the Spallation Neutron Source (SNS) project approval to begin Title I design of the proposed facility to be built at Oak Ridge National Laboratory (ORNL). During the conceptual design phase of the SNS project, the target station bulk-biological shield was characterized and the activation of the major targets station components was calculated. Shielding requirements were assessed with respect to weight, space, and dose-rate constraints for operating, shut-down, and accident conditions utilizing the SNS shield design criteria, DOE Order 5480.25, and requirements specified in 10 CFR 835. Since completion of the conceptual design phase, there have been major design changes to the target station as a result of the initial shielding and activation analyses, modifications brought about due to engineering concerns, and feedback from numerous external review committees. These design changes have impacted the results of the conceptual design analyses, and consequently, have required a re-investigation of the new design. Furthermore, the conceptual design shielding analysis did not address many of the details associated with the engineering design of the target station. In this paper, some of the proposed SNS target station preliminary Title I shielding design analyses will be presented. The SNS facility (with emphasis on the target station), shielding design requirements, calculational strategy, and source terms used in the analyses will be described. Preliminary results and conclusions, along with recommendations for additional analyses, will also be presented. (author)

  17. Alternative Fuels Data Center: Publications

    Science.gov (United States)

    Windstars; 14) and the use of alternative fuel vehicles at the Olympics. Alternative Fuels In Trucking, Vol and their economic and environmental benefits. This report is designed to share the experiences and National Academy of Engineering suggested that 'DOE might have its greatest impact by leading the private

  18. 20 CFR 404.535 - How much will we withhold from your title VIII and title XVI benefits to recover a title II...

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false How much will we withhold from your title... Officer § 404.535 How much will we withhold from your title VIII and title XVI benefits to recover a title II overpayment? (a) If past-due benefits are payable to you, we will withhold the lesser of the...

  19. 12 CFR 5.42 - Corporate title.

    Science.gov (United States)

    2010-01-01

    ... 18 U.S.C. 709, regarding false advertising and the misuse of names to indicate a Federal agency, and... the appropriate district office if it changes its corporate title. The notice must contain the old and...

  20. Code of Federal Regulations Title 21

    Data.gov (United States)

    U.S. Department of Health & Human Services — This database contains the most recent revision from the Government Printing Office (GPO) of the Code of Federal Regulations (CFR) Title 21 - Food and Drugs.

  1. The Need for Conciliation under Title VII

    Science.gov (United States)

    Pollard, William E.

    1975-01-01

    The AFL-CIO is committed to the task of eliminating discrimination and injustice in the workplace and is making efforts to expand the Equal Employment Opportunity Commission's conciliation efforts under Title Seven. (MW)

  2. Service Locator - Family Planning Title X

    Data.gov (United States)

    U.S. Department of Health & Human Services — This locator tool will help you find Title X family planning centers that provide high quality and cost-effective family planning and related preventive health...

  3. Sensitivity of the engineered barrier system (EBS) release rate to alternative conceptual models of advective release from waste packages under dripping fractures

    International Nuclear Information System (INIS)

    Lee, J.H.; Atkins, J.E.; McNeish, J.A.; Vallikat, V.

    1996-01-01

    The first model assumed that dripping water directly contacts the waste form inside the ''failed'' waste package and radionuclides are released from the EBS by advection. The second model assumed that dripping water is diverted around the package (because of corrosion products plugging the perforations), thereby being prevented from directly contacting the waste form. In the second model, radionuclides were assumed to diffuse through the perforations, and, once outside the waste package, to be released from the EBS by advection. For the case with the second EBS release model, most radionuclides had lower peak EBS release rates than with the first model. Impacts of the alternative EBS release models were greater for the radionuclides with low solubility. The analysis indicated that the EBS release model representing advection through a ''failed'' waste package (the first model) may be too conservative; thus a ''failed'' waste package container with multiple perforations may still be an important barrier to radionuclide release

  4. Alternate fusion fuels workshop

    International Nuclear Information System (INIS)

    1981-06-01

    The workshop was organized to focus on a specific confinement scheme: the tokamak. The workshop was divided into two parts: systems and physics. The topics discussed in the systems session were narrowly focused on systems and engineering considerations in the tokamak geometry. The workshop participants reviewed the status of system studies, trade-offs between d-t and d-d based reactors and engineering problems associated with the design of a high-temperature, high-field reactor utilizing advanced fuels. In the physics session issues were discussed dealing with high-beta stability, synchrotron losses and transport in alternate fuel systems. The agenda for the workshop is attached

  5. Audit-Proof Contracting for Federal Money for Children's Services: Financing Services for Children through Title XX and Other Programs. Manual 3.

    Science.gov (United States)

    Copeland, William C.

    This is the third of a 3-part series on how to locate, obtain, and manage Federal money for children's services. This manual concentrates on the contracting of money for specific programs. Emphasis is on Title XX of the Social Security Act, but attention is given also to alternative sources where Title XX funds are not sufficient. Although useful…

  6. Spray characteristics of dimethyl ether (D.M.E.) as on alternative fuel for diesel engine; Daitai diesel nenryo to shite no dimethyl ether (D.M.E.) no funmu tokusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Wakai, K; Nishida, K; Yoshizaki, T; Hiroyasu, H [Hiroshima University, Hiroshima (Japan)

    1997-10-01

    D.M.E. which was paid attention to as on alternative fuel for a diesel engine, was injected by using Bosch type injection pump and a hole nozzle into a high pressure and high temperature vessel. The spray was observed by using schlieren photography. Spray characteristics, such as, the tip penetration, the cone angle and the volume of the spray were and were compared with a diesel fuel spray. The following thing, and so on were found out as a results. The spray angle of the DME spray of atmosphere pressure Pa=0.1Mpa spreads out large in comparison with the diesel fuel spray, and the way of the change by the pressure is contrary to the case of the diesel fuel spray. 3 refs., 6 figs., 1 tab.

  7. Proceedings of the 1993 Windsor Workshop on Alternative Fuels

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    This report contains viewgraph papers on the following topics on alternative fuels: availability of alternative fueled engines and vehicles; emerging technologies; overcoming barriers to alternative fuels commercialization; infrastructure issues; and new initiatives in research and development.

  8. Alternative wastewatersystems

    DEFF Research Database (Denmark)

    Dyck-Madsen, Søren; Hoffmann, Birgitte; Gabriel, Søren

    1999-01-01

    The report:-  Communicates experiences from Swedish buildings from the establishment and running of alternative wastewater systems. Communicates pictures of alternative buildings and wastewater systems in Sweden. Gives a short evaluation of the performance and the sustainability of the systems....

  9. Engineering the central pathways in Lactococcus lactis: functional expression of the phosphofructokinase (pfk) and alternative oxidase (aox1) genes from Aspergillus niger in Lactococcus lactis facilitates improved carbon conversion rates under oxidizing conditions.

    Science.gov (United States)

    Papagianni, Maria; Avramidis, Nicholaos

    2012-08-10

    The present work describes a novel central pathway engineering method that has been designed with the aim to increase the carbon conversion rates under oxidizing conditions in L. lactis fermentations. The nisin producer L. lactis ATCC11454 strain has been genetically engineered by cloning a truncated version of the phosphofructokinase gene (pfk13), along with the pkaC, encoding for the catalytic subunit of cAMP-dependent protein kinase, and the alternative oxidase (aox1) genes of A. niger. Functional expression of the above genes resulted in enhanced PFK activity and the introduction of AOX activity and alternative respiration in the presence of a source of heme in the substrate, under fully aerobic growth conditions. The constructed strain is capable of fermenting high concentrations of glucose as was demonstrated in a series of glucostat fed-batch fermentations with glucose levels maintained at 55, 138 and 277 mM. The high maximum specific uptake rate of glucose of 1.8 mMs(-1)gCDW(-1) at 277 mM glucose is characteristic of the improved ability of the microorganism to handle elevated glucose concentrations under conditions otherwise causing severe reduction of PFK activity. The increased carbon flow through glycolysis led to increased protein synthesis that was reflected in increased biomass and nisin levels. The pfk 13-pkaC-aox1-transformant strain's fermentation at 277 mM glucose gave a final biomass concentration of 7.5 g/l and nisin activity of 14,000 IU/ml which is, compared to the parental strain's production levels at its optimal 55 mM glucose, increased by a factor of 2.34 for biomass and 4.37 for nisin. Copyright © 2012 Elsevier Inc. All rights reserved.

  10. Mechanical engineering education

    CERN Document Server

    Davim, J Paulo

    2012-01-01

    Mechanical Engineering is defined nowadays as a discipline "which involves the application of principles of physics, design, manufacturing and maintenance of mechanical systems". Recently, mechanical engineering has also focused on some cutting-edge subjects such as nanomechanics and nanotechnology, mechatronics and robotics, computational mechanics, biomechanics, alternative energies, as well as aspects related to sustainable mechanical engineering.This book covers mechanical engineering higher education with a particular emphasis on quality assurance and the improvement of academic

  11. The role of performance assessment in the evaluation of remedial action alternatives for the Radioactive Waste Management Complex (RWMC) at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Rood, A.S.; Case, M.J.

    1988-01-01

    The Idaho National Engineering Laboratory (INEL) is operated by the Department of Energy (DOE) and is involved in nuclear research and development. The Radioactive Waste Management Complex (RWMC) at the INEL serves as a disposal facility for low level radioactive wastes generated onsite. Transuranic (TRU) wastes received from other DOE sites are currently stored at the RWMC, but were buried at the facility from 1952 until 1970. Recent findings of the Subsurface Investigations Program have determined that migration of TRU nuclides and hazardous materials from the RWMC has occurred. The primary source of organics in the buried TRU waste was generated by the Rocky Flats Plant. The INEL has proposed an aggressive four-year action plan for buried TRU waste. As a part of this plan, a task has been identified to evaluate existing remedial technologies for preventing further contaminant migration or removing the source of TRU radionuclides and nonradioactive hazardous material from the RWMC. A systems approach is being applied to evaluate, compare and recommend technologies or combinations of technologies. One criterion used in the evaluation is the net risk reduction afforded by each proposed remedial action. The method used to develop the criterion relies on models to assess the potential pathways and scenarios for the migration of radioactive and nonradioactive materials and the subsequent exposure of individuals to those materials. This paper describes the approach used to assess the performance of various remedial actions and the results obtained to date

  12. A new alternative paraffinic-palmbiodiesel fuel for reducing polychlorinated dibenzo-p-dioxin/dibenzofuran emissions from heavy-duty diesel engines.

    Science.gov (United States)

    Lin, Yuan-Chung; Liu, Shou-Heng; Chen, Yan-Min; Wu, Tzi-Yi

    2011-01-15

    Polychlorinated dibenzo-p-dioxin/dibenzofuran (PCDD/F) emissions from heavy-duty diesel engines (HDDEs) fuelled with paraffinic-palmbiodiesel blends have been rarely addressed in the literature. A high-resolution gas chromatograph/high-resolution mass spectrometer (HRGC/HRMS) was used to analyze 17 PCDD/F species. Experimental results indicate that the main species of PCDD/Fs were OCDD (octachlorinated debenzo-p-dioxin) and OCDF (octachlorodibenzofuran), and they accounted for 40-50% of the total PCDD/Fs for all test fuels. Paraffinic-palmbiodiesel blends decreased PCDD/Fs by 86.1-88.9%, toxic PCDD/Fs by 91.9-93.0%, THC (total hydrocarbons) by 13.6-23.3%, CO (carbon monoxide) by 27.2-28.3%, and PM (particulate matter) by 21.3-34.2%. Using biodiesel blends, particularly BP9505 or BP8020, instead of premium diesel fuel (PDF) significantly reduced emissions of both PCDD/Fs and traditional pollutants. Using BP9505 (95vol% paraffinic fuel+5vol% palmbiodiesel) and BP8020 instead of PDF can decrease PCDD/F emissions by 5.93 and 5.99gI-TEQyear(-1) in Taiwan, respectively. Copyright © 2010. Published by Elsevier B.V.

  13. Alternative fuels for vehicles; Alternative drivmidler

    Energy Technology Data Exchange (ETDEWEB)

    2012-02-15

    Up until 2020 and onwards the analysis indicates that especially electricity, biogas and natural gas as propellants is economically attractive compared to conventional gasoline and diesel while other fuels have the same or higher costs for petrol and diesel. Especially biogas and electricity will also offer significant reductions in CO{sub 2} emissions, but also hydrogen, methanol, DME and to a lesser extent the second generation bioethanol and most of the other alternative fuels reduce CO{sub 2} emissions. Use of the traditional food-based first generation biofuels involves, at best, only modest climate benefits if land use changes are counted, and at worst, significant negative climate effects. Natural gas as a propellant involves a moderate climate gain, but may play a role for building infrastructure and market for gaseous fuels in large fleets, thereby contributing to the phasing in of biogas for transport. The electric-based automotive fuels are the most effective due to a high efficiency of the engine and an increasing proportion of wind energy in the electricity supply. The methanol track also has a relatively high efficiency. Among the others, the track based on diesel engines (biodiesel) is more effective than the track based on gasoline/Otto engines (gas and ethanol) as a result of the diesel engine's better efficiency. For the heavy vehicles all the selected alternative fuels to varying degrees reduce emissions of CO{sub 2}, particularly DME based on wood. The only exception to this is - as for passenger cars - the propellant synthetic diesel based on coal. (LN).

  14. Safety assessment of alternatives to shallow-land burial of low-level radioactive waste: Volume 2, Environmental conditions affecting reliability of engineered barriers

    International Nuclear Information System (INIS)

    Cerven, F.; Otis, M.D.

    1987-09-01

    The need for new disposal capacity for low-level radioactive waste (LLW) has led to a re-examination of disposal practices. A number of enhancements and alternatives to traditional shallow-land burial have been proposed to meet the need for new capacity and to address various concerns about the performance history of existing commercial LLW sites. Fifteen potentially important degradation mechanisms for a LLW facility are identified, categorized, and analyzed to determine their importance to the proper functioning of the disposal facility over its 500-year lifetime. Wind storms, biological intrusion, mechanical settling, freeze/thaw cycling, chemical degradation, wind erosion, and water erosion were considered the most important mechanisms. Data supporting concrete structure long-term performance in sulfate environments and long-term cover performance in erosive and biological intrusion environments were obtained. Research on the performance of covers and concrete structures in the presence of the other listed degradation mechanisms is recommended. 18 refs., 16 figs., 9 tabs

  15. How alternative are alternative fuels?

    OpenAIRE

    Soffritti, Tiziana; Danielis, Romeo

    1998-01-01

    Could alternative fuel vehicles contribute to a substantial reduction of air pollution? Is there a market for alternative fuel vehicles? Could a market be created via a pollution tax? The article answers these questions on the basis of the available estimates.

  16. Alternative detox.

    Science.gov (United States)

    Ernst, E

    2012-01-01

    The concept that alternative therapies can eliminate toxins and toxicants from the body, i.e. 'alternative detox' (AD) is popular. Selected textbooks and articles on the subject of AD. The principles of AD make no sense from a scientific perspective and there is no clinical evidence to support them. The promotion of AD treatments provides income for some entrepreneurs but has the potential to cause harm to patients and consumers. In alternative medicine, simplistic but incorrect concepts such as AD abound. AREAS TIMELY FOR RESEARCH: All therapeutic claims should be scientifically tested before being advertised-and AD cannot be an exception.

  17. Alternative Substrate Metabolism in Yarrowia lipolytica

    Directory of Open Access Journals (Sweden)

    Michael Spagnuolo

    2018-05-01

    Full Text Available Recent advances in genetic engineering capabilities have enabled the development of oleochemical producing strains of Yarrowia lipolytica. Much of the metabolic engineering effort has focused on pathway engineering of the product using glucose as the feedstock; however, alternative substrates, including various other hexose and pentose sugars, glycerol, lipids, acetate, and less-refined carbon feedstocks, have not received the same attention. In this review, we discuss recent work leading to better utilization of alternative substrates. This review aims to provide a comprehensive understanding of the current state of knowledge for alternative substrate utilization, suggest potential pathways identified through homology in the absence of prior characterization, discuss recent work that either identifies, endogenous or cryptic metabolism, and describe metabolic engineering to improve alternative substrate utilization. Finally, we describe the critical questions and challenges that remain for engineering Y. lipolytica for better alternative substrate utilization.

  18. 7 CFR 1927.55 - Title clearance services.

    Science.gov (United States)

    2010-01-01

    ... REGULATIONS TITLE CLEARANCE AND LOAN CLOSING Real Estate Title Clearance and Loan Closing § 1927.55 Title clearance services. (a) Responsibilities of closing agents. Services to be provided to the agency and the borrower by a closing agent in connection with the transaction vary depending on whether a title insurance...

  19. Title of the paper goes here second line

    Indian Academy of Sciences (India)

    %%Please download if these packages are not included %%in your local TeX distribution %%txfonts,balance,textcase,float %% \\begin{document} %%paper title %%For line breaks, \\\\ can be used within title \\title{Title of the paper goes here\\\\ second line} %%author names are separated by comma (,) %%use \\and before ...

  20. Roadmap Through Title XX. Financing Services for Children Through Title XX and Other Programs: Manual 5.

    Science.gov (United States)

    Copeland, William C.; Iversen, Iver A.

    This manual, part of a Hecht Institute four-manual series entitled Financing Children's Services Through Title XX and Related Programs, teaches what Title XX regulations are, what they mean, and what actions and procedures are commanded by them. The first section covers the necessity of rule systems, the characteristics of a good rule system and…

  1. Title List of documents made publicly available

    International Nuclear Information System (INIS)

    1982-07-01

    The Title List of Documents Made Publicly Available is a monthly publication. It contains descriptions of the information received and generated by the US Nuclear Regulatory Commission (NRC). This information includes: (1) docketed material associated with civilian nuclear power plants and other uses of radioactive materials and (2) nondocketed material received and generated by NRC pertinent to its role as a regulatory agency. As used here, docketed does not refer to Court dockets; it refers to the system by which NRC maintains its regulatory records. This series of documents is indexed by a Personal Author Index, a Corporate Source Index, and a Report Number Index. The docketed information contained in the Title List includes the information formerly issued through the Department of Energy publication Power Reactor Docket Information, last published in January 1979. Microfiche of the docketed information listed in the Title List is available for sale on a subscription basis from the National Technical Information Service (NTIS)

  2. Title List of documents made publicly available

    International Nuclear Information System (INIS)

    1982-06-01

    The Title List of Documents Made Publicly Available is a monthly publication. It contains descriptions of the information received and generated by the US Nuclear Regulatory Commission (NRC). This information includes: (1) docketed material associated with civilian nuclear power plants and other uses of radioactive materials and (2) nondocketed material received and generated by NRC pertinent to its role as a regulatory agency. As used here, docketed does not refer to Court dockets; it refers to the system by which NRC maintains its regulatory records. This series of documents is indexed by a Personal Author Index, a Corporate Source Index, and a Report Number Index. The docketed information contained in the Title List includes the information formerly issued throught the Department of Energy publication Power Reactor Docket Information, last published in January 1979. Microfiche of the docketed information listed in the Title List is available for sale on a subscription basis from the National Technical Information Service (NTIS)

  3. Quarterly title list for the period ending September 1976

    International Nuclear Information System (INIS)

    1976-01-01

    The title list of the Max-Planck-Institut fuer Plasmaphysik and the Projektgruppe fuer Laserforschung of the MPG is concerned with the period from July until September 1976, and it contains: a) 12 titles and abstracts of laboratory reports, b) 37 titles of publications (30 abstracts), c) 20 titles of articles submitted for publication (16 abstracts), and d) 25 titles of lectures (12 abstracts). (GG) [de

  4. Energy Information Data Base: serial titles

    International Nuclear Information System (INIS)

    1980-06-01

    The Department of Energy Technical Information Center (TIC) is responsible for creating bibliographic data bases that are used in the announcement and retrieval of publications dealing with all phases of energy. The TIC interactive information processing system makes use of a number of computerized authorities so that consistency can be maintained and indexes can be produced. One such authority is the Energy Information Data Base: Serial Titles. This authority contains the full and abbreviated journal title, country of publication, CODEN, and certain codes. This revision replaces previous revisions of this document

  5. Title list of documents made publicly available

    International Nuclear Information System (INIS)

    1991-01-01

    The Title List of Documents Made Publicly Available is a monthly publication. It contains descriptions of the information received and generated by the US Nuclear Regulatory Commission (NRC). This information includes docketed material associated with civilian nuclear power plants and other uses of radioactive materials and nondocketed material received and generated by NRC pertinent to its role as a regulatory agency. This series of documents is indexed by a Personal Author Index, a Corporate Source Index, and a Report Number Index. The docketed information contained in the Title List includes the information formerly issued though the Department of Energy publication Power Reactor Docket Information, last published in January 1979

  6. 20 CFR 408.931 - How much will we withhold from your title II and title XVI benefits to recover a title VIII...

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false How much will we withhold from your title II... and Overpayments Adjustment of Title II Benefits § 408.931 How much will we withhold from your title...-due benefits. (b)(1) We will collect the overpayment from current monthly benefits due in a month...

  7. Rehabilitation Engineering Sourcebook [and] Rehabilitation Engineering Sourcebook Supplement I.

    Science.gov (United States)

    Institute for Information Studies, Falls Church, VA.

    Intended for use by rehabilitation counselors and work supervisors, the sourcebook contains 173 problems and solutions provided by rehabilitation engineering. A section titled "Guidelines for Formulating Problem Statements" is intended to summarize the most effective ways for either disabled individuals or rehabilitation practitioners to…

  8. Cosmic alternatives?

    Science.gov (United States)

    Gregory, Ruth

    2009-04-01

    "Cosmologists are often in error but never in doubt." This pithy characterization by the Soviet physicist Lev Landau sums up the raison d'être of Facts and Speculations in Cosmology. Authors Jayant Narlikar and Geoffrey Burbidge are proponents of a "steady state" theory of cosmology, and they argue that the cosmological community has become fixated on a "Big Bang" dogma, suppressing alternative viewpoints. This book very much does what it says on the tin: it sets out what is known in cosmology, and puts forward the authors' point of view on an alternative to the Big Bang.

  9. Factors Influencing Title VII Bilingual Program Institutionalization.

    Science.gov (United States)

    Lewis, Gerald R.; And Others

    1985-01-01

    This study of the primary restraining and driving forces that influence Title VII bilingual education programs found the external environment, the local community, to be the main factor influencing institutionalization and self-renewal. The internal environment--the local school, and the local school's organization or central office, school board,…

  10. What Difference Does a Title Make

    DEFF Research Database (Denmark)

    Balle, Søren Hattesen

    out by Gerard Genette, by naming and “designat[ing] it as precisely as possible and without too much risk of confusion” (Genette, 1997). In accordance with its title the poem thus represents the discourse of a newsreader neutrally reporting the events of war scenario. However, each section of the poem...

  11. 76 FR 60593 - Title VI; Proposed Circular

    Science.gov (United States)

    2011-09-29

    ..., several of them related to ambiguous language in the existing Circular. The proposed Circular reorganizes... regional entity, and inclusive of public and private entities. This term is used exclusively in Chapter IV... revisions to the Title VI Circular. The section that addresses the existing requirement for a Language...

  12. Browse Title Index - African Journals Online

    African Journals Online (AJOL)

    Items 801 - 850 of 1006 ... Issue, Title. Vol 59, No 4 (2017), Spatial patterns and determinants of fertility levels among women of childbearing age in Nigeria, Abstract PDF. Oluwayemisi O. Alaba, Olusanya E. Olubusoye, J.O. Olaomi. Vol 55, No 1 (2013), Spirit(ed) away: preventing foetal alcohol syndrome with motivational ...

  13. 36 CFR 254.15 - Title standards.

    Science.gov (United States)

    2010-07-01

    ...) Conveyances of lands from the United States are made by patent, quitclaim deed, or deed and without express or implied warranties, except as to hazardous substances pursuant to § 254.3 of this subpart. (c) Title... of the existing use(s) authorized under the terms of the grant, permit, easement, or lease. The non...

  14. Providing Transparency to the Title IX Process

    Science.gov (United States)

    Hartle, Terry

    2017-01-01

    When U.S. Secretary of Education Betsy DeVos announced Sept. 7, 2017, that her department would revisit how Title IX rules are enforced with respect to campus sexual assault, she said the first step would be a "transparent notice and comment process" to replace the 2011 "guidance" (and follow up 2014 guidance) that has been…

  15. Software Development Framework For Electronic Land Titles ...

    African Journals Online (AJOL)

    Record keeping is a fundamental activity of public administration. Land Titles management in Nigeria, by virtue of the Land use act 1990, is one of the functions of government. Most of the records hitherto used in managing the records of lands are documented on paper. We carried out an investigation into the suitability of ...

  16. Browse Title Index - African Journals Online

    African Journals Online (AJOL)

    Items 151 - 200 of 771 ... Issue, Title. Vol 33, No 4 (2013), Community-researcher liaisons: the Pathways to Resilience Project Advisory Panel, Abstract PDF. LC Theron. Vol 37, No 3 (2017), Comparing the achievement goal orientation of mathematics learners with and without attention-deficit hyperactivity disorder, Abstract ...

  17. Civil Engineering Technology Program Guide.

    Science.gov (United States)

    Georgia Univ., Athens. Dept. of Vocational Education.

    This program guide presents civil engineering technology curriculum for technical institutes in Georgia. The general information section contains the following: purpose and objectives; program description, including admissions, typical job titles, and accreditation and certification; and curriculum model, including standard curriculum sequence and…

  18. Growing Alternatives

    DEFF Research Database (Denmark)

    Bagger-Petersen, Mai Corlin

    2014-01-01

    From 2014, Anhui Province will pilot a reform of the residential land market in China, thus integrating rural Anhui in the national housing market. In contrast, artist and activist Ou Ning has proposed the Bishan time money currency, intending to establish an alternative economic circuit in Bishan...

  19. Alternative Veier

    DEFF Research Database (Denmark)

    Kruse, Tove Elisabeth; Salamonsen, Anita

    reflektioner omkring patienters brug af og erfaringer med alternativ behandling. Patientorganisationer, organisatoner for alternative behandlere og organisationer for læger og medicinstuderende har læst bogens patienthistorier og deres perspektiver lægges frem. Til slut i bogen diskuteres betydningen af de...

  20. Discovering English with the Sketch Engine

    Science.gov (United States)

    Thomas, James

    2014-01-01

    "Discovering English with the Sketch Engine" is the title of a new book (Thomas, 2014) which introduces the use of corpora in language study, teaching, writing and translating. It focuses on using the Sketch Engine to identify patterns of normal usage in many aspects of English ranging from morphology to discourse and pragmatics. This…