Land-Based Mobile Laser Scanning Systems: a Review

Science.gov (United States)

Puente, I.; González-Jorge, H.; Arias, P.; Armesto, J.

2011-09-01

Mobile mapping has been using various photogrammetric techniques for many years. In recent years, there has been an increase in the number of mobile mapping systems using laser scanners available in the market, partially because of the improvement in GNSS/INS performance for direct georeferencing. In this article, some of the most important land-based mobile laser scanning (MLS) systems are reviewed. Firstly, the main characteristics of MLS systems vs. airborne (ALS) and terrestrial laser scanning (TLS) systems are compared. Secondly, a short overview of the mobile mapping technology is also provided so that the reader can fully grasp the complexity and operation of these devices. As we put forward in this paper, a comparison of different systems is briefly carried out regarding specifications provided by the manufacturers. Focuses on the current research are also addressed with emphasis on the practical applications of these systems. Most of them have been utilized for data collection on road infrastructures or building façades. This article shows that MLS technology is nowadays well established and proven, since the demand has grown to the point that there are several systems suppliers offering their products to satisfy this particular market.

Radioisotopic and thermographic imaging of the lower limbs oedema - comparison diagnostic techniques

International Nuclear Information System (INIS)

Stepien, A.; Pawlus, J.; Nowak, E.; Kulka, J.; Gielzycki, J.; Kraft, O.

2005-01-01

In this paper, authors achieved comparison between lymphoscintigraphy and thermography in patients with limbs oedema. It allow to determinate current role of lymphoscintigraphy and verify useful of thermography in limbs oedema diagnosis. Analysis included 60 patients with the lower limbs oedema. Each patients Doppler duplex scan and thermographic study was performed. Additionally, 10 patients were classified to the lymphoscintigraphy. Thermography: In studies camera ThermaCAM S60 (FLIR SYSTEM) were used. Infrared radiation detector was 320 x 240 uncooled microbolometers with thermal resolution - 0.08 o C (for 30 o C). Lymphoscintigraphy: Each patient received subcutaneous, in the second web space, Nanosis (schering) labeled 99m Tc. Dynamic data acquisition has been started immediately after injection the radiotracer to the both extremities using digital gamma camera X Ring (Mediso). Static study of whole body was performed after 1.5 hour. Thermal disorders were observed in 58 patients. On the base ultrasound and clinical examinations 10 patients were classified to lymphoscintigraphy. In this group in 5 cases traits lymphatic insufficient were observed. Thermographic study in group of patients with scintigraphic disorders was showed regional hypothermia, with small regions of hypothermia in tissues included oedema. Lymphoscintigraphy is a useful and indispensable tool in oedema diagnosis. In patients with insufficient of lymphatic system, thermography comparison to lymphoscintigraphy, in clinical diagnosis did not influence on the future diagnosis and therapeutics proceedings. Regional hyperthermic disorders in patients with limbs oedema, who had negative results of examinations (Doppler duplex scan and lymphoscintigraphy), could indicate on inflammatory complications. In cases of venous insufficient thermography allow to visualize specific venous disorders. (author)

Advances in thermographic signal reconstruction

Science.gov (United States)

Shepard, Steven M.; Frendberg Beemer, Maria

2015-05-01

Since its introduction in 2001, the Thermographic Signal Reconstruction (TSR) method has emerged as one of the most widely used methods for enhancement and analysis of thermographic sequences, with applications extending beyond industrial NDT into biomedical research, art restoration and botany. The basic TSR process, in which a noise reduced replica of each pixel time history is created, yields improvement over unprocessed image data that is sufficient for many applications. However, examination of the resulting logarithmic time derivatives of each TSR pixel replica provides significant insight into the physical mechanisms underlying the active thermography process. The deterministic and invariant properties of the derivatives have enabled the successful implementation of automated defect recognition and measurement systems. Unlike most approaches to analysis of thermography data, TSR does not depend on flawbackground contrast, so that it can also be applied to characterization and measurement of thermal properties of flaw-free samples. We present a summary of recent advances in TSR, a review of the underlying theory and examples of its implementation.

Infrared-thermographic screening of the activity and enantioselectivity of enzymes.

Science.gov (United States)

Reetz, M T; Hermes, M; Becker, M H

2001-05-01

The infrared radiation caused by the heat of reaction of an enantioselective enzyme-catalyzed transformation can be detected by modern photovoltaic infrared (IR)-thermographic cameras equipped with focal-plane array detectors. Specifically, in the lipase-catalyzed enantioselective acylation of racemic 1-phenylethanol, the (R)- and (S)-substrates are allowed to react separately in the wells of microtiter plates, the (R)-alcohol showing hot spots in the IR-thermographic images. Thus, highly enantioselective enzymes can be identified at kinetic resolution.

Thermographic analysis of waveguide-irradiated insect pupae

Science.gov (United States)

Olsen, Richard G.; Hammer, Wayne C.

1982-01-01

Pupae of the insect Tenebrio molitor L. were thermographically imaged during waveguide irradiation through longitudinal slots. T. molitor pupae have been subjects of microwave-induced teratology for a number of years, but until now the smallness of the insect has prevented detailed dosimetry. High-resolution thermographic imaging equipment was used to obtain the magnitude and spatial distribution of absorbed microwave energy at three frequencies, 1.3, 5.95, and 10 GHz. The detail of the thermal images obtained is sufficient to show the differential heating of structures as small as a single insect leg. Results show that the electrical properties of the head, thorax, and abdomen are sufficiently different to seriously impair the usefulness of any theoretical dosimetric model of homogeneous composition. Some general features of correlation with a slab model in waveguide are given.

Aerial thermography from low-cost UAV for the generation of thermographic digital terrain models

Science.gov (United States)

Lagüela, S.; Díaz-Vilariño, L.; Roca, D.; Lorenzo, H.

2015-03-01

Aerial thermography is performed from a low-cost aerial vehicle, copter type, for the acquisition of data of medium-size areas, such as neighbourhoods, districts or small villages. Thermographic images are registered in a mosaic subsequently used for the generation of a thermographic digital terrain model (DTM). The thermographic DTM can be used with several purposes, from classification of land uses according to their thermal response to the evaluation of the building prints as a function of their energy performance, land and water management. In the particular case of buildings, apart from their individual evaluation and roof inspection, the availability of thermographic information on a DTM allows for the spatial contextualization of the buildings themselves and the general study of the surrounding area for the detection of global effects such as heat islands.

Infrared Thermographic Diagnosis Mechanism for Fault Detection of Ball Bearing under Dynamic Loading Conditions

International Nuclear Information System (INIS)

Seo, Jin Ju; Yoon, Hanvit; Kim, Dong Yeon; Hong, Dong Pyo; Kim, Won Tae

2011-01-01

Fault detection for dynamic loading conditions of rotational machineries was considered from the contactless, non-destructive infrared thermographic method, rather than the traditional diagnosis method. In this paper, by applying a rotating deep-grooved ball bearing, passive thermographic experiment was performed as an alternative way proceeding the traditional fault monitoring. In addition, the thermographic experiments were compared with the vibration spectrum analysis to evaluate the efficiency of the proposed method. Based on the results, it was concluded the temperature characteristics of the ball bearing under dynamic loading conditions were analyzed thoroughly

Assessment of lower extremity ischemia using smartphone thermographic imaging

Directory of Open Access Journals (Sweden)

Peter H. Lin, MD

2017-12-01

Full Text Available Conventional diagnostic modalities for assessing arterial circulation or tissue perfusion include blood pressure measurement, ultrasound evaluation, and contrast-based angiographic assessment. An infrared thermal camera can detect infrared radiation energy from the human body, which generates a thermographic image to allow tissue perfusion analysis. We describe a smartphone-based miniature thermal imaging system that can be used as an adjunctive imaging modality to assess tissue perfusion. This smartphone-based camera device is noninvasive, simple to use, and cost-effective in assessing patients with lower extremity tissue perfusion. Assessment of patients with lower extremity arterial ischemia can be performed by a variety of diagnostic modalities, including ankle-brachial index, absolute systolic ankle or toe pressure, transcutaneous oximetry, arterial Doppler waveform, arterial duplex ultrasound, computed tomography scan, arterial angiography, and thermal imaging. We herein describe a noninvasive imaging modality using smartphone-based infrared thermography.

TSI Model 3936 Scanning Mobility Particle Spectrometer Instrument Handbook

Energy Technology Data Exchange (ETDEWEB)

Kuang, C. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2016-02-01

The Model 3936 Scanning Mobility Particle Spectrometer (SMPS) measures the size distribution of aerosols ranging from 10 nm up to 1000 nm. The SMPS uses a bipolar aerosol charger to keep particles within a known charge distribution. Charged particles are classified according to their electrical mobility, using a long-column differential mobility analyzer (DMA). Particle concentration is measured with a condensation particle counter (CPC). The SMPS is well-suited for applications including: nanoparticle research, atmospheric aerosol studies, pollution studies, smog chamber evaluations, engine exhaust and combustion studies, materials synthesis, filter efficiency testing, nucleation/condensation studies, and rapidly changing aerosol systems.

The consistency of thermographic findings in breast screening

International Nuclear Information System (INIS)

Pflanzer, K.; Kleedorfer, D.; Pflanzer, D.; Fochem, K.

1983-01-01

Thermography is a valuable complementary method in breast examination, but is not a suitable screening method. However, the results of control investigations in 200 females who were reexamined after at least two years, showed no change in the thermographic pattern in 87.5% of the women. In 10.5% the change in thermogram was due to pathological changes, whilst no explanation could be found in only 2% of cases. This high stability rate of the thermograms permits an alternative procedure: If, one year after a basic examination which includes clinical investigation, mammography and thermography, the thermographic pattern is identical with the first, no mammography is necessary. On the occasion of the next control, mammography should be carried out again at the time of the subsequent control examination. This schedule permits a reduction in irradiation without reducing the security of diagnosis. (Author)

Investigation of the effect of engine lubricant oil on remote temperature sensing using thermographic phosphors

Energy Technology Data Exchange (ETDEWEB)

Abou Nada, Fahed, E-mail: Fahed.Abou_Nada@forbrf.lth.se; Aldén, Marcus; Richter, Mattias

2016-11-15

Phosphor thermometry, a remote temperature sensing technique, is widely implemented to measure the temperature of different combustion engines components. The presence of engine lubricant can influence the behavior of the applied sensor materials, known as thermographic phosphors, and thus leading to erroneous temperature measurements. The effect of two engine lubricants on decay times originating from six different thermographic phosphors was investigated. The decay time of each thermographic phosphor was investigated as a function of lubricant/phosphor mass ratio. Tests were conducted at temperatures around 293 K and 376 K for both lubricants. The investigations revealed that ZnO:Zn and ZnS:Ag are the only ones that exhibit a change of the decay time as function of the lubricant/phosphor mass ratio. While the remaining thermographic phosphors, namely BaMg{sub 2}Al{sub 16}O{sub 27}:Eu (BAM), Al{sub 2}O{sub 3}-coated BaMg{sub 2}Al{sub 16}O{sub 27}:Eu, La{sub 2}O{sub 2}S:Eu, Mg{sub 3}F{sub 2}GeO{sub 4}:Mn, displayed no sensitivity of their characteristic decay time on to the presence of lubricant on the porous coating. Biases in the calculated temperature are to be expected if the utilized thermographic phosphor displays decay time sensitivity to the existence of the engine lubricant within the sensor. Such distortions are concealed and can occur undetected leading to false temperature readings for the probed engine component.

Thermographic Inspection of Fatigue Crack by Using Contact Thermal Resistance

Energy Technology Data Exchange (ETDEWEB)

Yang, Seung Yong; Kim, No Hyu [Korean University of Technology and Education, Cheonan (Korea, Republic of)

2013-04-15

Fatigue crack was detected from a temperature change around surface crack using the thermographic technique. Thermal gradient across the crack decreased very much due to thermal resistance of contact surface in the crack. Heat diffusion flow passing through the discontinuity was visualized in temperature by infrared camera to find and locate the crack. A fatigue crack specimen(SM-45C), which was prepared according to KS specification and notched in its center to initiate fatigue crack from the notch tip, was heated by halogen lamp at the end of one side to generate a heat diffusion flow in lateral direction. A abrupt jump in temperature across the fatigue crack was observed in thermographic image, by which the crack could be located and sized from temperature distribution.

Thermographic Inspection of Fatigue Crack by Using Contact Thermal Resistance

International Nuclear Information System (INIS)

Yang, Seung Yong; Kim, No Hyu

2013-01-01

Fatigue crack was detected from a temperature change around surface crack using the thermographic technique. Thermal gradient across the crack decreased very much due to thermal resistance of contact surface in the crack. Heat diffusion flow passing through the discontinuity was visualized in temperature by infrared camera to find and locate the crack. A fatigue crack specimen(SM-45C), which was prepared according to KS specification and notched in its center to initiate fatigue crack from the notch tip, was heated by halogen lamp at the end of one side to generate a heat diffusion flow in lateral direction. A abrupt jump in temperature across the fatigue crack was observed in thermographic image, by which the crack could be located and sized from temperature distribution.

Local imaging of high mobility two-dimensional electron systems with virtual scanning tunneling microscopy

Energy Technology Data Exchange (ETDEWEB)

Pelliccione, M. [Department of Applied Physics, Stanford University, 348 Via Pueblo Mall, Stanford, California 94305 (United States); Stanford Institute for Materials and Energy Sciences, SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Department of Physics, University of California, Santa Barbara, Santa Barbara, California 93106 (United States); Bartel, J.; Goldhaber-Gordon, D. [Stanford Institute for Materials and Energy Sciences, SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Department of Physics, Stanford University, 382 Via Pueblo Mall, Stanford, California 94305 (United States); Sciambi, A. [Department of Applied Physics, Stanford University, 348 Via Pueblo Mall, Stanford, California 94305 (United States); Stanford Institute for Materials and Energy Sciences, SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Pfeiffer, L. N.; West, K. W. [Department of Electrical Engineering, Princeton University, Princeton, New Jersey 08544 (United States)

2014-11-03

Correlated electron states in high mobility two-dimensional electron systems (2DESs), including charge density waves and microemulsion phases intermediate between a Fermi liquid and Wigner crystal, are predicted to exhibit complex local charge order. Existing experimental studies, however, have mainly probed these systems at micron to millimeter scales rather than directly mapping spatial organization. Scanning probes should be well-suited to study the spatial structure of these states, but high mobility 2DESs are found at buried semiconductor interfaces, beyond the reach of conventional scanning tunneling microscopy. Scanning techniques based on electrostatic coupling to the 2DES deliver important insights, but generally with resolution limited by the depth of the 2DES. In this letter, we present our progress in developing a technique called “virtual scanning tunneling microscopy” that allows local tunneling into a high mobility 2DES. Using a specially designed bilayer GaAs/AlGaAs heterostructure where the tunnel coupling between two separate 2DESs is tunable via electrostatic gating, combined with a scanning gate, we show that the local tunneling can be controlled with sub-250 nm resolution.

Brief communication "Application of mobile laser scanning in snow cover profiling"

Directory of Open Access Journals (Sweden)

S. Kaasalainen

2011-03-01

Full Text Available We present a snowmobile-based mobile mapping system and its first application to snow cover roughness and change detection measurement. The ROAMER mobile mapping system, constructed at the Finnish Geodetic Institute, consists of the positioning and navigating systems, a terrestrial laser scanner, and the carrying platform (a snowmobile sledge in this application. We demonstrate the applicability of the instrument to snow cover roughness profiling and change detection by presenting preliminary results from a mobile laser scanning (MLS campaign. The results show the potential of MLS for fast and efficient snow profiling from large areas in a millimetre scale.

Treatment of Reflex sympathetic dystrophy with Bee venom -Using Digital Infrared Thermographic Imaging-

Directory of Open Access Journals (Sweden)

Myung-jang Lim

2006-12-01

Full Text Available Objectives : The purpose of this case is to report the patient with Reflex sympathetic dystrophy, who is improved by Bee venom. Method : We treated the patient with Bee venom who was suffering from Reflex sympathetic dystrophy, using Digital Infrared Thermographic Imaging and Verbal Numerical Rating Scale(VNRS to evaluate the therapeutic effects. We compared the temperature of the patient body before and after treatment. Result and Conclusion : We found that Bee venom had excellent outcome to relieve pain, atrophy and ankle joint ROM, and that Bee venom also had clinical effect on hypothermia on the Digital Infrared Thermographic Imaging.

Integrated procedures and monitoring methodologies for thermographic investigations of architectural heritage: two applicative cases in Sicily, Italy

International Nuclear Information System (INIS)

Bianco, A.

2013-01-01

The paper explains some opportunities and limitations of thermographic investigations in terms of their capability to define the conservative conditions of architectural heritage and in terms of the historical recollection for a technical diagnosis. Different approaches are demonstrated in two case studies: the first integrates thermography with other investigative methods; the second combines thermographic monitoring with hygrothermal monitoring. (author)

Thermographic and radionuclide investigation in combined diagnosis of breast cancer

International Nuclear Information System (INIS)

Abushakhmanov, A.Kh.

1986-01-01

The results of examination of 157 women with breast diseases are given. Breast cancer was diagnosed in 94 patients, benign diseases in 63. The combined use of the thermographic and radionuclide methods was shown to raise the accuracy of breast cancer diagnosis

Mass prophylactic screening of the organized female populaton using the Thermograph-Computer System

International Nuclear Information System (INIS)

Vepkhvadze, R.Ya.; Khvedelidze, E.Sh.

1984-01-01

Organizational aspects of the Thermograph Computer System usage have been analyzed. It has been shown that results of thermodiagnosis completely coincide with clinical conclusion, but roentrenological method permits to reveal a disease only for 19 patients from 36 ones. It is possible to examine 120 women for the aim of early diagnosis of mammary gland diseases during the day operating hours with the use of the Thermograph Computer System. A movable thermodiagnostic room simultaneoUsly served as an inspection room to discover visual forms of tumor diseases including diseases of cervix uteri and may be used for mass preventive examination of the organized female population

Miniaturized NIR scanning grating spectrometer for use in mobile phones

Science.gov (United States)

Knobbe, Jens; Pügner, Tino; Grüger, Heinrich

2016-05-01

An extremely miniaturized scanning grating spectrometer at the size of a sugar cube has been developed at Fraunhofer IPMS. To meet the requirements for the integration into a mobile phone a new system approach has been pursued. The key component within the system is a silicon-based deflectable diffraction grating with an integrated driving mechanism. A first sample of the new spectrometer was built and characterized. It was found to have a spectral range from 950 nm to 1900 nm at a resolution of 10 nm. The results show that the performance of the new MEMS spectrometer is in good agreement with the requirements for mobile phone integration.

Mobile Laser Scanning for Indoor Modelling

Directory of Open Access Journals (Sweden)

C. Thomson

2013-10-01

Full Text Available The process of capturing and modelling buildings has gained increased focus in recent years with the rise of Building Information Modelling (BIM. At the heart of BIM is a process change for the construction and facilities management industries whereby a BIM aids more collaborative working through better information exchange, and as a part of the process Geomatic/Land Surveyors are not immune from the changes. Terrestrial laser scanning has been proscribed as the preferred method for rapidly capturing buildings for BIM geometry. This is a process change from a traditional measured building survey just with a total station and is aided by the increasing acceptance of point cloud data being integrated with parametric building models in BIM tools such as Autodesk Revit or Bentley Architecture. Pilot projects carried out previously by the authors to investigate the geometry capture and modelling of BIM confirmed the view of others that the process of data capture with static laser scan setups is slow and very involved requiring at least two people for efficiency. Indoor Mobile Mapping Systems (IMMS present a possible solution to these issues especially in time saved. Therefore this paper investigates their application as a capture device for BIM geometry creation over traditional static methods through a fit-for-purpose test.

Mobile Laser Scanning for Indoor Modelling

Science.gov (United States)

Thomson, C.; Apostolopoulos, G.; Backes, D.; Boehm, J.

2013-10-01

The process of capturing and modelling buildings has gained increased focus in recent years with the rise of Building Information Modelling (BIM). At the heart of BIM is a process change for the construction and facilities management industries whereby a BIM aids more collaborative working through better information exchange, and as a part of the process Geomatic/Land Surveyors are not immune from the changes. Terrestrial laser scanning has been proscribed as the preferred method for rapidly capturing buildings for BIM geometry. This is a process change from a traditional measured building survey just with a total station and is aided by the increasing acceptance of point cloud data being integrated with parametric building models in BIM tools such as Autodesk Revit or Bentley Architecture. Pilot projects carried out previously by the authors to investigate the geometry capture and modelling of BIM confirmed the view of others that the process of data capture with static laser scan setups is slow and very involved requiring at least two people for efficiency. Indoor Mobile Mapping Systems (IMMS) present a possible solution to these issues especially in time saved. Therefore this paper investigates their application as a capture device for BIM geometry creation over traditional static methods through a fit-for-purpose test.

Application of SVM classifier in thermographic image classification for early detection of breast cancer

Science.gov (United States)

Oleszkiewicz, Witold; Cichosz, Paweł; Jagodziński, Dariusz; Matysiewicz, Mateusz; Neumann, Łukasz; Nowak, Robert M.; Okuniewski, Rafał

2016-09-01

This article presents the application of machine learning algorithms for early detection of breast cancer on the basis of thermographic images. Supervised learning model: Support vector machine (SVM) and Sequential Minimal Optimization algorithm (SMO) for the training of SVM classifier were implemented. The SVM classifier was included in a client-server application which enables to create a training set of examinations and to apply classifiers (including SVM) for the diagnosis and early detection of the breast cancer. The sensitivity and specificity of SVM classifier were calculated based on the thermographic images from studies. Furthermore, the heuristic method for SVM's parameters tuning was proposed.

Scanned proton radiotherapy for mobile targets-the effectiveness of re-scanning in the context of different treatment planning approaches and for different motion characteristics

NARCIS (Netherlands)

Knopf, Antje-Christin; Hong, Theodore S; Lomax, Antony

2011-01-01

The most advanced delivery technique for proton radiotherapy is active spot scanning. So far, predominantly static targets have been treated with active spot scanning, since mobile targets in combination with dynamic treatment delivery can lead to interplay effects, causing inhomogeneous dose

Thermographic inspection of pipes, tanks, and containment liners

Energy Technology Data Exchange (ETDEWEB)

Renshaw, Jeremy B., E-mail: jrenshaw@epri.com; Muthu, Nathan [Electric Power Research Institute, 1300 West WT Harris Blvd., Charlotte, NC 28262 (United States); Lhota, James R.; Shepard, Steven M., E-mail: sshepard@thermalwave.com [Thermal Wave Imaging, 845 Livernois St., Ferndale, MI 48220 (United States)

2015-03-31

Nuclear power plants are required to operate at a high level of safety. Recent industry and license renewal commitments aim to further increase safety by requiring the inspection of components that have not traditionally undergone detailed inspected in the past, such as tanks and liners. NEI 09-14 requires the inspection of buried pipes and tanks while containment liner inspections are required as a part of license renewal commitments. Containment liner inspections must inspect the carbon steel liner for defects - such as corrosion - that could threaten the pressure boundary and ideally, should be able to inspect the surrounding concrete for foreign material that could be in contact with the steel liner and potentially initiate corrosion. Such an inspection requires a simultaneous evaluation of two materials with very different material properties. Rapid, yet detailed, inspection results are required due to the massive size of the tanks and containment liners to be inspected. For this reason, thermal NDE methods were evaluated to inspect tank and containment liner mockups with simulated defects. Thermographic Signal Reconstruction (TSR) was utilized to enhance the images and provide detailed information on the sizes and shapes of the observed defects. The results show that thermographic inspection is highly sensitive to the defects of interest and is capable of rapidly inspecting large areas.

Continuous scanning of the mobility and size distribution of charged clusters and nanometer particles in atmospheric air and the Balanced Scanning Mobility Analyzer BSMA

Science.gov (United States)

Tammet, H.

2006-12-01

Measuring of charged nanometer particles in atmospheric air is a routine task in research on atmospheric electricity, where these particles are called the atmospheric ions. An aspiration condenser is the most popular instrument for measuring atmospheric ions. Continuous scanning of a mobility distribution is possible when the aspiration condenser is connected as an arm of a balanced bridge. Transfer function of an aspiration condenser is calculated according to the measurements of geometric dimensions, air flow rate, driving voltage, and electric current. The most complicated phase of the calibration is the estimation of the inlet loss of ions due to the Brownian deposition. The available models of ion deposition on the protective inlet screen and the inlet control electrofilter have the uncertainty of about 20%. To keep the uncertainty of measurements low the adsorption should not exceed a few tens of percent. The online conversion of the mobility distribution to the size distribution and a correct reduction of inlet losses are possible when air temperature and pressure are measured simultaneously with the mobility distribution. Two instruments called the Balanced Scanning Mobility Analyzers (BSMA) were manufactured and tested in routine atmospheric measurements. The concentration of atmospheric ions of the size of about a few nanometers is very low and a high air flow rate is required to collect enough of ion current. The air flow of 52 l/s exceeds the air flow in usual aerosol instruments by 2-3 orders of magnitude. The high flow rate reduces the time of ion passage to 60 ms and the heating of air in an analyzer to 0.2 K, which suppresses a possible transformation of ions inside the instrument. The mobility range of the BSMA of 0.032-3.2 cm 2 V - 1 s - 1 is logarithmically uniformly divided into 16 fractions. The size distribution is presented by 12 fractions in the diameter range of 0.4-7.5 nm. The measurement noise of a fraction concentration is typically

Thermographic Inspections And The Residential Conservation Service Program (RCS)

Science.gov (United States)

Ward, Ronald J.

1983-03-01

Rhode Islanders Saving Energy (RISE) is a non-profit corporation founded in 1977 to provide Rhode Island residents with a variety of energy conservation services. Since January of 1981, it has been performing energy audits in compliance with the Department of Energy's (DOE) Residential Conservation Service Program (RCS). One aspect of the RCS program is the performance of inspections on energy conservation activities completed according to RCS installation guidelines. This paper will describe both the use and results of thermographic inspections within the RISE program. The primary objective of these inspections has been to assure the quality of the building envelope after completion of retrofit measures. Thermal anamolies have been detected that vary in size, location and probable cause. Approximately 37% of all jobs performed through RISE in conjunction with the RCS program have required remedial work as a result of problems that were identi-fied during the thermographic inspection. This percentage was much higher when infra-red inspections were conducted on "Non-RCS" retrofits. Statistics will be presented that provide an interesting insight on the quality of retrofit work when performed in associa-tion with a constant inspection process.

An Autonomous Ultra-Wide Band-Based Attitude and Position Determination Technique for Indoor Mobile Laser Scanning

Directory of Open Access Journals (Sweden)

Lawrence Lau

2018-04-01

Full Text Available Mobile laser scanning (MLS has been widely used in three-dimensional (3D city modelling data collection, such as Google cars for Google Map/Earth. Building Information Modelling (BIM has recently emerged and become prominent. 3D models of buildings are essential for BIM. Static laser scanning is usually used to generate 3D models for BIM, but this method is inefficient if a building is very large, or it has many turns and narrow corridors. This paper proposes using MLS for BIM 3D data collection. The positions and attitudes of the mobile laser scanner are important for the correct georeferencing of the 3D models. This paper proposes using three high-precision ultra-wide band (UWB tags to determine the positions and attitudes of the mobile laser scanner. The accuracy of UWB-based MLS 3D models is assessed by comparing the coordinates of target points, as measured by static laser scanning and a total station survey.

Quantitative thermographic imagery in the evaluation of antenna heating patterns

International Nuclear Information System (INIS)

Pearce, J.A.; Baughman, R.R.

1984-01-01

In quantitative thermographic imaging the temperature distribution of a surface is inferred from measurement of the radiant energy leaving the surface. Digital image processing and calibration methods allow the subtraction of preexisting temperature gradients so that precise heating patterns can be obtained. The primary limitation of quantitative thermography is that noise in the photodetector limits minimum resolvable temperature difference to around 0.5 0 C since frame integration cannot be used on the transient temperature distributions expected. The authors have developed and evaluated nonlinear smoothing operators which reduce the noise variance so that temperature differences of 0.1 0 C can be measured. They have applied digital thermographic imaging in the measurement of heating patterns obtained from two roughly orthogonal microwave antennas: a spiral antenna and a bow-tie antenna. These two antenna types are orthogonal in that the spiral has an H-field essentially normal to the phantom surface and the bow-tie has an E-field essentially normal to the surface. The resulting heating patterns clearly show the effect of non-uniform phantom electrical properties on the heating profiles obtained

Initial Tests and Accuracy Assesment of a Compact Mobile Laser Scanning System

Science.gov (United States)

Julge, K.; Ellmann, A.; Vajakas, T.; Kolka, R.

2016-06-01

Mobile laser scanning (MLS) is a faster and cost-effective alternative to static laser scanning, even though there is a slight trade-off in accuracy. This contribution describes a compact mobile laser scanning system mounted on a vehicle. The technical parameters of the used system components, i.e. a small LIDAR sensor Velodyne VLP-16 and a dual antenna GNSS/INS system Advanced Navigation Spatial Dual, are reviewed, along with the integration of these components for spatial data acquisition. Calculation principles of 3D coordinates from the real-time data of all the involved sensors are discussed. The field tests were carried out in a controlled environment of a parking lot and at different velocities. Experiments were carried out to test the ability of the GNSS/INS system to cope with difficult conditions, e.g. sudden movements due to cornering or swerving. The accuracy of the resulting MLS point cloud is evaluated with respect to high-accuracy static terrestrial laser scanning data. Problems regarding combining LIDAR, GNSS and INS sensors are outlined, as well as the initial accuracy assessments. Initial tests revealed errors related to insufficient quality of inertial data and a need for the trajectory post-processing calculations. Although this study was carried out while the system was mounted on a car, there is potential for operating the system on an unmanned aerial vehicle, all-terrain vehicle or in a backpack mode due to its relatively compact size.

INITIAL TESTS AND ACCURACY ASSESMENT OF A COMPACT MOBILE LASER SCANNING SYSTEM

Directory of Open Access Journals (Sweden)

K. Julge

2016-06-01

Full Text Available Mobile laser scanning (MLS is a faster and cost-effective alternative to static laser scanning, even though there is a slight trade-off in accuracy. This contribution describes a compact mobile laser scanning system mounted on a vehicle. The technical parameters of the used system components, i.e. a small LIDAR sensor Velodyne VLP-16 and a dual antenna GNSS/INS system Advanced Navigation Spatial Dual, are reviewed, along with the integration of these components for spatial data acquisition. Calculation principles of 3D coordinates from the real-time data of all the involved sensors are discussed. The field tests were carried out in a controlled environment of a parking lot and at different velocities. Experiments were carried out to test the ability of the GNSS/INS system to cope with difficult conditions, e.g. sudden movements due to cornering or swerving. The accuracy of the resulting MLS point cloud is evaluated with respect to high-accuracy static terrestrial laser scanning data. Problems regarding combining LIDAR, GNSS and INS sensors are outlined, as well as the initial accuracy assessments. Initial tests revealed errors related to insufficient quality of inertial data and a need for the trajectory post-processing calculations. Although this study was carried out while the system was mounted on a car, there is potential for operating the system on an unmanned aerial vehicle, all-terrain vehicle or in a backpack mode due to its relatively compact size.

Interest and limits of microwaves thermographic measurements for the diagnosis and pronostic of local acute exposure in the pig

International Nuclear Information System (INIS)

Daburon, F.; Lefaix, J.L.; Remy, J.; Fayart, G.; Tricaud, Y.

1985-01-01

Microwaves thermographic measurements were carried out on 30 pigs following local exposure of the thigh by a collimated source of iridium 192 at doses ranging between 30 and 84 Gy (2 cm depth dose). Measurement and data processing methods were developed both qualitatively (thermographic images vs anatomo-clinical evolution of the lesions) and quantitatively (by means of indexes calculated from the rough thermographic data to evaluate the relations between the intensity of the local thermic reaction and the applied dose or dose rate). Beside the diagnostic value of the method, which accounts for the global radiological injuries better than the physical dose really distributed, its pronostic value -much more reliable- makes it possible to estimate the severity of the injuries and their later evolution very early (between 10 and 15 days) [fr

Evaluation in vitro of effects of Er:YAG and Nd:YAG lasers irradiation on root canal wall, by stereoscopy, scanning electron micrography and thermographic camera

International Nuclear Information System (INIS)

Goya, Claudia

2001-01-01

This study was carried out to evaluate in vitro the effects of Nd:YAG laser and Er:YAG laser irradiation in the root canal wall by SEM, evaluating the apical leakage and the temperature changes during the laser irradiation. Seventy four extracted human teeth were used, they were instrumented and divided into seven groups of 10 teeth each. The teeth were evaluated through stereoscopy, by SEM, and with the thermographic camera. The Nd:YAG laser irradiation parameters were 100 mJ/p, 15 Hz, and Er:YAG laser were 160 mJ/p and 10 Hz, the irradiation was 4 times at 2 mm/sec speed, with 20 sec interval. The apical leakage was not observed in the teeth irradiated by Nd:YAG laser alone or in association with Er:YAG laser. However in the teeth irradiated only by the Er:YAG laser we observed a little leakage. By SEM observation the Nd:YAG laser irradiation showed melting and recrystallization in the dentin surface closing dentinal tubules, and in the samples irradiated by Er:Y AG laser a clean surface, opened dentinal tubules, and the combination by two lasers, showed melting covering some dentinal tubules The thermographic study found the temperature increase was not more than 6 deg C. This study showed the safety parameters applications of Er:YAG laser in association with Nd:YAG laser in root canal treatment, in order to not cause thermal damages to the periodontal tissues. (author)

Application of Mobile Laser Scanning for Lean and Rapid Highway Maintenance and Construction

Science.gov (United States)

2015-08-28

Mobile Terrestrial Laser Scanning (MTLS) is an emerging technology that combines the use of a laser scanner(s), the Global Navigation Satellite System (GNSS), and an Inertial Measurement Unit (IMU) on a vehicle to collect geo-spatial data. The overal...

Motion Detection from Mobile Robots with Fuzzy Threshold Selection in Consecutive 2D Laser Scans

Directory of Open Access Journals (Sweden)

María A. Martínez

2015-01-01

Full Text Available Motion detection and tracking is a relevant problem for mobile robots during navigation to avoid collisions in dynamic environments or in applications where service robots interact with humans. This paper presents a simple method to distinguish mobile obstacles from the environment that is based on applying fuzzy threshold selection to consecutive two-dimensional (2D laser scans previously matched with robot odometry. The proposed method has been tested with the Auriga-α mobile robot in indoors to estimate the motion of nearby pedestrians.

A review of thermographic techniques for damage investigation in composites

Directory of Open Access Journals (Sweden)

Laura Vergani

2014-01-01

Full Text Available The aim of this work is a review of scientific results in the literature, related to the application of thermographic techniques to composite materials. Thermography is the analysis of the surface temperature of a body by infrared rays detection via a thermal-camera. The use of this technique is mainly based on the modification of the surface temperature of a material, when it is stimulated by means of a thermal or mechanical external source. The presence of defects, in fact, induces a localized variation in its temperature distribution and, then, the measured values of the surface temperature can be used to localize and evaluate the dimensions and the evolution of defects. In the past, many applications of thermography were proposed on homogeneous materials, but only recently this technique has also been extended to composites. In this work several applications of thermography to fibres reinforced plastics are presented. Thermographic measurements are performed on the surface of the specimens, while undergoing static and dynamic tensile loading. The joint analysis of thermal and mechanical data allows one to assess the damage evolution and to study the damage phenomenon from both mechanical and energetic viewpoints. In particular, one of the main issues is to obtain information about the fatigue behaviour of composite materials, by following an approach successfully applied to homogenous materials. This approach is based on the application of infrared thermography on specimens subjected to static or stepwise dynamic loadings and on the definition of a damage stress, D, that is correlated to the fatigue strength of the material. A wide series of experimental fatigue tests has been carried out to verify if the value of the damage stress, D, is correlated with the fatigue strength of the material. The agreement between the different values is good, showing the reliability of the presented thermographic techniques, to the study of composite

Fiber Optic Thermographic Detection of Flaws in Composites

Science.gov (United States)

Wu, Meng-Chou; Winfree, William P.

2009-01-01

Optical fibers with multiple Bragg gratings bonded to surfaces of structures were used for thermographic detection of subsurface defects in structures. The investigated structures included a 10-ply composite specimen with subsurface delaminations of various sizes and depths. Both during and following the application of a thermal heat flux to the surface, the individual Bragg grating sensors measured the temporal and spatial temperature variations. The obtained data were analyzed with thermal modeling to reveal particular characteristics of the interested areas. These results were found to be consistent with the simulation results.

Thermographic and histological analysis of rabbit different tenorrhaphies techniques (4 and 6 strands after early active mobilization

Directory of Open Access Journals (Sweden)

Rodrigo Arenhart

Full Text Available Introduction This research is based on the results of the surgeries of tenorraphy, which have been improved due to the association between strong and not voluminous sutures and physiotherapic protocols, which preconize the early active motion to the postoperative period. Objective To evaluate the healing process in vivo in different types of tenorraphies. Methods Thirty-six rabbits that underwent early active motion after tenorraphy. The sample was constituted of 3 groups of 12, in accordance with the 3 different types of suture (Brasil, Indiana and Tsai. Results On the 15th and 30th days after the surgery, thermographic and histological analyses revealed similar results that all groups showed similar behaviors in the same time of surgical repair, just differentiating between the periods. On the 30th day analysis were observed that collagen fibers being more exuberant thickening, thus being able to offer higher tensile strength to the tendon. Conclusion That suggests early active motion may be increased gradually to around the 30th day taking this as clinical relevance.

Forest Inventory with Terrestrial LiDAR: A Comparison of Static and Hand-Held Mobile Laser Scanning

Directory of Open Access Journals (Sweden)

Sébastien Bauwens

2016-06-01

Full Text Available The application of static terrestrial laser scanning (TLS in forest inventories is becoming more effective. Nevertheless, the occlusion effect is still limiting the processing efficiency to extract forest attributes. The use of a mobile laser scanner (MLS would reduce this occlusion. In this study, we assessed and compared a hand-held mobile laser scanner (HMLS with two TLS approaches (single scan: SS, and multi scan: MS for the estimation of several forest parameters in a wide range of forest types and structures. We found that SS is competitive to extract the ground surface of forest plots, while MS gives the best result to describe the upper part of the canopy. The whole cross-section at 1.3 m height is scanned for 91% of the trees (DBH > 10 cm with the HMLS leading to the best results for DBH estimates (bias of −0.08 cm and RMSE of 1.11 cm, compared to no fully-scanned trees for SS and 42% fully-scanned trees for MS. Irregularities, such as bark roughness and non-circular cross-section may explain the negative bias encountered for all of the scanning approaches. The success of using MLS in forests will allow for 3D structure acquisition on a larger scale and in a time-efficient manner.

AUTOMATIC RAILWAY POWER LINE EXTRACTION USING MOBILE LASER SCANNING DATA

Directory of Open Access Journals (Sweden)

S. Zhang

2016-06-01

Full Text Available Research on power line extraction technology using mobile laser point clouds has important practical significance on railway power lines patrol work. In this paper, we presents a new method for automatic extracting railway power line from MLS (Mobile Laser Scanning data. Firstly, according to the spatial structure characteristics of power-line and trajectory, the significant data is segmented piecewise. Then, use the self-adaptive space region growing method to extract power lines parallel with rails. Finally use PCA (Principal Components Analysis combine with information entropy theory method to judge a section of the power line whether is junction or not and which type of junction it belongs to. The least squares fitting algorithm is introduced to model the power line. An evaluation of the proposed method over a complicated railway point clouds acquired by a RIEGL VMX450 MLS system shows that the proposed method is promising.

Automatic recognition of thermographic examinations for early detection of breast cancer

Science.gov (United States)

Matysiewicz, Mateusz; Neumann, Łukasz; Nowak, Robert M.; Okuniewski, Rafał; Oleszkiewicz, Witold; Cichosz, Paweł; Jagodziński, Dariusz

2016-09-01

This article describes the processing and classification of thermographic examinations taken with device developed by Braster SA. The device records the surface temperature of the breast skin using the liquid crystal matrices. Images are analyzed with the use of machine learning algorithms. The result of classification is available after a few minutes and when it detects suspicious changes patient may be referred for detailed examinations.

Plasmatic and thermographic consequences of local acute irradiation; a qualitative and quantitative analysis in the pig

International Nuclear Information System (INIS)

Lefaix, J.L; Daburon, F.; Crechet, F.; Tricaud, Y.

1987-04-01

Acute phase reactant proteins associated with thermographic measurements and enzymatic activity assays in plasma were carried out on 39 pigs, following local exposure of the thigh to a collimated source of iridium 192 at doses ranging between 30 and 84 Gy (2 cm depth dose). The inflammatory response after irradiation, from day 1 to day 30 was accompanied by plasma protein changes associated with an elevation of local and general temperatures in irradiated animals. Degenerative processes in muscle led to an increase of plasmatic creatine kinase and lactate-dehydrogenase. Results were developed qualitatively (distribution pattern of proteins, thermographic measurements, enzymatic activities and clinical evolution of the lesions) and qualitatively (plasma level of creatine kinase versus applied radiation doses and pharmalogical treatments) [fr

ANALYSIS OF MOBILE LASER SCANNING DATA AND MULTI-VIEW IMAGE RECONSTRUCTION

Directory of Open Access Journals (Sweden)

C. Briese

2012-07-01

Full Text Available The combination of laser scanning (LS, active, direct 3D measurement of the object surface and photogrammetry (high geometric and radiometric resolution is widely applied for object reconstruction (e.g. architecture, topography, monitoring, archaeology. Usually the results are a coloured point cloud or a textured mesh. The geometry is typically generated from the laser scanning point cloud and the radiometric information is the result of image acquisition. In the last years, next to significant developments in static (terrestrial LS and kinematic LS (airborne and mobile LS hardware and software, research in computer vision and photogrammetry lead to advanced automated procedures in image orientation and image matching. These methods allow a highly automated generation of 3D geometry just based on image data. Founded on advanced feature detector techniques (like SIFT (Scale Invariant Feature Transform very robust techniques for image orientation were established (cf. Bundler. In a subsequent step, dense multi-view stereo reconstruction algorithms allow the generation of very dense 3D point clouds that represent the scene geometry (cf. Patch-based Multi-View Stereo (PMVS2. Within this paper the usage of mobile laser scanning (MLS and simultaneously acquired image data for an advanced integrated scene reconstruction is studied. For the analysis the geometry of a scene is generated by both techniques independently. Then, the paper focuses on the quality assessment of both techniques. This includes a quality analysis of the individual surface models and a comparison of the direct georeferencing of the images using positional and orientation data of the on board GNSS-INS system and the indirect georeferencing of the imagery by automatic image orientation. For the practical evaluation a dataset from an archaeological monument is utilised. Based on the gained knowledge a discussion of the results is provided and a future strategy for the integration of

Methods to attack or defend the professional integrity and competency of infrared thermographers and their work; what every attorney and infrared thermographer needs to know before going into a lawsuit

Science.gov (United States)

Colbert, Fred

2013-05-01

There has been a significant increase in the number of in-house Infrared Thermographic Predictive Maintenance programs for Electrical/Mechanical inspections as compared to out-sourced programs using hired consultants. In addition, the number of infrared consulting services companies offering out-sourced programs has also has grown exponentially. These market segments include: Building Envelope (commercial and residential), Refractory, Boiler Evaluations, etc... These surges are driven by two main factors: 1. The low cost of investment in the equipment (the cost of cameras and peripherals continues to decline). 2. Novel marketing campaigns by the camera manufacturers who are looking to sell more cameras into an otherwise saturated market. The key characteristics of these campaigns are to over simplify the applications and understate the significances of technical training, specific skills and experience that's needed to obtain the risk-lowering information that a facility manager needs. These camera selling campaigns focuses on the simplicity of taking a thermogram, but ignores the critical factors of what it takes to actually perform and manage a creditable, valid IR program, which in-turn expose everyone to tremendous liability. As the In-house vs. Out-sourced consulting services compete for market share head to head with each other in a constricted market space, the price for out-sourced/consulting services drops to try to compete on price for more market share. The consequences of this approach are, something must be compromised to be able to stay competitive from a price point, and that compromise is the knowledge, technical skills and experience of the thermographer. This also ends up being reflected back into the skill sets of the in-house thermographer as well. This over simplification of the skill and experience is producing the "Perfect Storm" for Infrared Thermography, for both in-house and out-sourced programs.

MIMIC: An Innovative Methodology for Determining Mobile Laser Scanning System Point Density

Directory of Open Access Journals (Sweden)

Conor Cahalane

2014-08-01

Full Text Available Understanding how various Mobile Mapping System (MMS laser hardware configurations and operating parameters exercise different influence on point density is important for assessing system performance, which in turn facilitates system design and MMS benchmarking. Point density also influences data processing, as objects that can be recognised using automated algorithms generally require a minimum point density. Although obtaining the necessary point density impacts on hardware costs, survey time and data storage requirements, a method for accurately and rapidly assessing MMS performance is lacking for generic MMSs. We have developed a method for quantifying point clouds collected by an MMS with respect to known objects at specified distances using 3D surface normals, 2D geometric formulae and line drawing algorithms. These algorithms were combined in a system called the Mobile Mapping Point Density Calculator (MIMIC and were validated using point clouds captured by both a single scanner and a dual scanner MMS. Results from MIMIC were promising: when considering the number of scan profiles striking the target, the average error equated to less than 1 point per scan profile. These tests highlight that MIMIC is capable of accurately calculating point density for both single and dual scanner MMSs.

Television-aided thermographic investigations in nuclear and solid state research

International Nuclear Information System (INIS)

Buettig, H.; Wollschlaeger, K.

1983-01-01

After a brief review of the physical and hardware fundamentals of televison-aided thermographic investigations, two practical examples of nuclear and solid state research work are presented. The problems discussed concern studies of the relative density distribution in beams of particles (ions, electrons, neutral atoms) or of visible radiation on the one hand, and the optimization of operating conditions in heavy-current implantations (ion implantation in Si at ion beam currents up to 60 μA) on the other hand

Thermographic process monitoring in powderbed based additive manufacturing

Energy Technology Data Exchange (ETDEWEB)

Krauss, Harald, E-mail: harald.krauss@iwb.tum.de; Zaeh, Michael F. [AMLab, iwb Application Center Augsburg, Technische Universität München (Germany); Zeugner, Thomas [Augsburg University (Germany)

2015-03-31

Selective Laser Melting is utilized to build metallic parts directly from CAD-Data by solidification of thin powder layers through application of a fast scanning laser beam. In this study layerwise monitoring of the temperature distribution is used to gather information about the process stability and the resulting part quality. The heat distribution varies with different kinds of parameters including scan vector length, laser power, layer thickness and inter-part distance in the job layout which in turn influence the resulting part quality. By integration of an off-axis mounted uncooled thermal detector the solidification as well as the layer deposition are monitored and evaluated. Errors in the generation of new powder layers usually result in a locally varying layer thickness that may cause poor part quality. For effect quantification, the locally applied layer thickness is determined by evaluating the heat-up of the newly deposited powder. During the solidification process space and time-resolved data is used to characterize the zone of elevated temperatures and to derive locally varying heat dissipation properties. Potential quality indicators are evaluated and correlated to the resulting part quality: Thermal diffusivity is derived from a simplified heat dissipation model and evaluated for every pixel and cool-down phase of a layer. This allows the quantification of expected material homogeneity properties. Maximum temperature and time above certain temperatures are measured in order to detect hot spots or delamination issues that may cause a process breakdown. Furthermore, a method for quantification of sputter activity is presented. Since high sputter activity indicates unstable melt dynamics this can be used to identify parameter drifts, improper atmospheric conditions or material binding errors. The resulting surface structure after solidification complicates temperature determination on the one hand but enables the detection of potential surface defects

The effect of airflow on thermographically determined temperature of the distal forelimb of the horse.

Science.gov (United States)

Westermann, S; Stanek, C; Schramel, J P; Ion, A; Buchner, H H F

2013-09-01

Current literature suggests that thermographic imaging of horses should be performed in a draught-free room. However, studies on the effect of airflow on determined temperature have not been published. To investigate effects of airflow on thermographically determined temperature of horses' forelimbs; to assess the relationship of wind velocity, rectal temperature, ambient temperature and humidity. Thermographic images were obtained for the forelimbs of 6 horses in a draught-free room. Three replicates (R) with defined wind velocities (R1, 0.5-1.0 m/s; R2, 1.3-2.6 m/s; and R3, 3.0-4.0 m/s) were conducted. Each replicate consisted of a baseline image, a 15 min phase with the wind on and a 15 min phase with the wind off. We exposed only the right leg to airflow and determined the temperature by thermography with the wind on and wind off. Temperature differences between baseline and wind on, between wind on and wind off and between different wind velocities were analysed by a general linear model, Student's paired t test and ANOVA. After the onset of wind, the temperature on the right forelimb decreased within 1-3 min (by approximately 0.6°C at R1, 1.5°C at R2 and 2.1°C at R3). With the wind off, the temperature increased within 3 min (by approximately 1.2°C at R1, 1.7°C at R2 and 2.1°C at R3). With increasing wind velocity, the temperature differences between baseline and wind on and between wind on and wind off increased significantly. Barely noticeable wind velocities caused a decrease in thermographically determined temperatures of the forelimbs of the horse. Further research is required to assess the influence of airflow on other parts of the body and at different ambient temperatures, as well as the effect on horses with inflammatory lesions, especially of the distal limbs. It is essential for practitioners to perform thermography on horses in a draught-free environment in order to avoid false-positive or -negative diagnoses. © 2012 EVJ Ltd.

Thermographic skin temperature measurement compared with cold sensation in predicting the efficacy and distribution of epidural anesthesia.

Science.gov (United States)

Bruins, Arnoud A; Kistemaker, Kay R J; Boom, Annemieke; Klaessens, John H G M; Verdaasdonk, Rudolf M; Boer, Christa

2018-04-01

Due to the high rates of epidural failure (3-32%), novel techniques are required to objectively assess the successfulness of an epidural block. In this study we therefore investigated whether thermographic temperature measurements have a higher predictive value for a successful epidural block when compared to the cold sensation test as gold standard. Epidural anesthesia was induced in 61 patients undergoing elective abdominal, thoracic or orthopedic surgery. A thermographic picture was recorded at 5, 10 and 15 min following epidural anesthesia induction. After 15 min a cold sensation test was performed. Epidural anesthesia is associated with a decrease in skin temperature. Thermography predicts a successful epidural block with a sensitivity of 54% and a PPV of 92% and a specificity of 67% and a NPV of 17%. The cold sensation test shows a higher sensitivity and PPV than thermography (97 and 93%), but a lower specificity and NPV than thermography (25 and 50%). Thermographic temperature measurements can be used as an additional and objective method for the assessment of the effectiveness of an epidural block next to the cold sensation test, but have a low sensitivity and negative predictive value. The local decrease in temperature as observed in our study during epidural anesthesia is mainly attributed to a core-to-peripheral redistribution of body heat and vasodilation.

Computer vision syndrome (CVS) - Thermographic Analysis

Science.gov (United States)

Llamosa-Rincón, L. E.; Jaime-Díaz, J. M.; Ruiz-Cardona, D. F.

2017-01-01

The use of computers has reported an exponential growth in the last decades, the possibility of carrying out several tasks for both professional and leisure purposes has contributed to the great acceptance by the users. The consequences and impact of uninterrupted tasks with computers screens or displays on the visual health, have grabbed researcher’s attention. When spending long periods of time in front of a computer screen, human eyes are subjected to great efforts, which in turn triggers a set of symptoms known as Computer Vision Syndrome (CVS). Most common of them are: blurred vision, visual fatigue and Dry Eye Syndrome (DES) due to unappropriate lubrication of ocular surface when blinking decreases. An experimental protocol was de-signed and implemented to perform thermographic studies on healthy human eyes during exposure to dis-plays of computers, with the main purpose of comparing the existing differences in temperature variations of healthy ocular surfaces.

Temperature measurements on fast-rotating objects using a thermographic camera with an optomechanical image derotator

Science.gov (United States)

Altmann, Bettina; Pape, Christian; Reithmeier, Eduard

2017-08-01

Increasing requirements concerning the quality and lifetime of machine components in industrial and automotive applications require comprehensive investigations of the components in conditions close to the application. Irregularities in heating of mechanical parts reveal regions with increased loading of pressure, draft or friction. In the long run this leads to damage and total failure of the machine. Thermographic measurements of rotating objects, e.g., rolling bearings, brakes, and clutches provide an approach to investigate those defects. However, it is challenging to measure fast-rotating objects accurately. Currently one contact-free approach is performing stroboscopic measurements using an infrared sensor. The data acquisition is triggered so that the image is taken once per revolution. This leads to a huge loss of information on the majority of the movement and to motion blur. The objective of this research is showing the potential of using an optomechanical image derotator together with a thermographic camera. The derotator follows the rotation of the measurement object so that quasi-stationary thermal images during motion can be acquired by the infrared sensor. Unlike conventional derotators which use a glass prism to achieve this effect, the derotator within this work is equipped with a sophisticated reflector assembly. These reflectors are made of aluminum to transfer infrared radiation emitted by the rotating object. Because of the resulting stationary thermal image, the operation can be monitored continuously even for fast-rotating objects. The field of view can also be set to a small off-axis region of interest which then can be investigated with higher resolution or frame rate. To depict the potential of this approach, thermographic measurements on a rolling bearings in different operating states are presented.

An Online Solution of LiDAR Scan Matching Aided Inertial Navigation System for Indoor Mobile Mapping

Directory of Open Access Journals (Sweden)

Xiaoji Niu

2017-01-01

Full Text Available Multisensors (LiDAR/IMU/CAMERA integrated Simultaneous Location and Mapping (SLAM technology for navigation and mobile mapping in a GNSS-denied environment, such as indoor areas, dense forests, or urban canyons, becomes a promising solution. An online (real-time version of such system can extremely extend its applications, especially for indoor mobile mapping. However, the real-time response issue of multisensors is a big challenge for an online SLAM system, due to the different sampling frequencies and processing time of different algorithms. In this paper, an online Extended Kalman Filter (EKF integrated algorithm of LiDAR scan matching and IMU mechanization for Unmanned Ground Vehicle (UGV indoor navigation system is introduced. Since LiDAR scan matching is considerably more time consuming than the IMU mechanism, the real-time synchronous issue is solved via a one-step-error-state-transition method in EKF. Stationary and dynamic field tests had been performed using a UGV platform along typical corridor of office building. Compared to the traditional sequential postprocessed EKF algorithm, the proposed method can significantly mitigate the time delay of navigation outputs under the premise of guaranteeing the positioning accuracy, which can be used as an online navigation solution for indoor mobile mapping.

Automatic Indoor Building Reconstruction from Mobile Laser Scanning Data

Science.gov (United States)

Xie, L.; Wang, R.

2017-09-01

Indoor reconstruction from point clouds is a hot topic in photogrammetry, computer vision and computer graphics. Reconstructing indoor scene from point clouds is challenging due to complex room floorplan and line-of-sight occlusions. Most of existing methods deal with stationary terrestrial laser scanning point clouds or RGB-D point clouds. In this paper, we propose an automatic method for reconstructing indoor 3D building models from mobile laser scanning point clouds. The method includes 2D floorplan generation, 3D building modeling, door detection and room segmentation. The main idea behind our approach is to separate wall structure into two different types as the inner wall and the outer wall based on the observation of point distribution. Then we utilize a graph cut based optimization method to solve the labeling problem and generate the 2D floorplan based on the optimization result. Subsequently, we leverage an ?-shape based method to detect the doors on the 2D projected point clouds and utilize the floorplan to segment the individual room. The experiments show that this door detection method can achieve a recognition rate at 97% and the room segmentation method can attain the correct segmentation results. We also evaluate the reconstruction accuracy on the synthetic data, which indicates the accuracy of our method is comparable to the state-of-the art.

Certification of building thermographers: experiences after three courses

Science.gov (United States)

Kauppinen, Timo; Hekkanen, Martti; Paloniitty, Sauli; Krankka, Juha

2006-04-01

The certification procedure of building thermographers was started in 2003, even though thermography has been used in Finland in building survey since late 70's. There has been about a 25 years' unorganized and more or less wild period, without any generally accepted rules for interpretation, as well as how to order thermography services, how to report the results, how to do the practical work in the buildings etc. The service was provided by consultants with varied backgrounds. More operators have come into the market and building developers and contractors have begun to use thermography for quality control in new building and in renovation planning. In the year 2004 various organizations in building trade launched a pilot project to certificate building thermographers. The structure and the topics of the course were introduced in Thermosense 2005. By the end of the year 2005 the third course was completed. From the beginning of the procedure to the end of the third course about 40 persons have received a certificate. During the certification process, two guidelines have been published, as part of RT (Building Information) - files: instructions for ordering, for practical field work and for reporting of thermography survey in buildings. The guidelines also contain basics for interpretation. The interpretation is consistent with the other existing directions (building codes etc). At the turn of 2005 - 2006 a new book of building thermography was published. There is still lack of comprehensive as well as unambiguous rules for interpretation. In the paper we will present experiences on the courses, the main problems posed to the participants and findings during the last two - three years' field work. We will also introduce briefly the structure and content of the guidelines and an example how to use thermography as a tool of quality control in new building. The case studies are new one-family houses in a housing fair and exhibition area in the city of Oulu.

Surface Temperature Measurements from a Stator Vane Doublet in a Turbine Engine Afterburner Flame Using a YAG:Tm Thermographic Phosphor

Science.gov (United States)

Eldridge, J. I.; Walker, D. G.; Gollub, S. L.; Jenkins, T. P.; Allison, S. W.

2015-01-01

Luminescence-based surface temperature measurements were obtained from a YAG:Tm-coated stator vane doublet exposed to the afterburner flame of a J85 test engine at University of Tennessee Space Institute (UTSI). The objective of the testing was to demonstrate that reliable surface temperatures based on luminescence decay of a thermographic phosphor producing short-wavelength emission could be obtained from the surface of an actual engine component in a high gas velocity, highly radiative afterburner flame environment. YAG:Tm was selected as the thermographic phosphor for its blue emission at 456 nm (1D23F4 transition) and UV emission at 365 nm (1D23H6 transition) because background thermal radiation is lower at these wavelengths, which are shorter than those of many previously used thermographic phosphors. Luminescence decay measurements were acquired using a probe designed to operate in the afterburner flame environment. The probe was mounted on the sidewall of a high-pressure turbine vane doublet from a Honeywell TECH7000 turbine engine coated with a standard electron-beam physical vapor deposited (EB-PVD) 200-m-thick TBC composed of yttria-stabilized zirconia (YSZ) onto which a 25-m-thick YAG:Tm thermographic phosphor layer was deposited by solution precursor plasma spray (SPPS). Spot temperature measurements were obtained by measuring luminescence decay times at different afterburner power settings and then converting decay time to temperature via calibration curves. Temperature measurements using the decays of the 456 and 365 nm emissions are compared. While successful afterburner environment measurements were obtained to about 1300C with the 456 nm emission, successful temperature measurements using the 365 nm emission were limited to about 1100C due to interference by autofluorescence of probe optics at short decay times.

Effect of frost on phosphorescence for thermographic phosphor thermometry

Science.gov (United States)

Kim, Dong; Kim, Mirae; Kim, Kyung Chun

2017-12-01

In this study, we analyzed phosphorescence lifetime and its accuracy by growing frost for thermographic phosphor thermometry in a low-temperature environment. Mg4FGeO6:Mn particles were coated on an aluminum plate and excited with a UV-LED to obtain phosphorescence signals. The surface temperature was maintained at  -20, -15, -10 °C, and the phosphorescence signal was acquired as the frost grew for 3700 s. The lifetime was calculated and compared with the calibration curve under no-frost conditions. The error of the measured lifetime was within 0.7% of that in the no-frost conditions. A 2D surface temperature profile of the target plate was successfully obtained with the frost formation.

Thermographic observation of the divertor target plates in the stellarators W7-AS and W7-X

International Nuclear Information System (INIS)

Hildebrandt, D.; Gadelmeier, F.; Grigull, P.; McCormick, K.; Naujoks, D.; Suender, D.

2003-01-01

Thermography is applied on the stellarator W7-AS to monitor the thermal load of the recently installed divertor targets. A three dimensional numerical code was developed to evaluate power fluxes arriving at the targets from the measured temporal evolution of the surface temperature distribution. Values of the thermal conductivity of the used CFC-target material for all three directions are required for this evaluation and determined by observing the propagation of controlled heat pulses applied by an infrared laser. The evaluation of the thermographic measurements during plasma operation shows characteristic spatial and temporal features of the arrived heat fluxes. Significant features in high density regimes like plasma detachment from the divertor target plates or strongly enhanced localised plasma radiation (MARFE) has been observed by the installed infrared cameras. The implications of these observations for the thermographic system for W7-X are shortly addressed

Thermographic Imaging of the Superficial Temperature in Racing Greyhounds before and after the Race

Directory of Open Access Journals (Sweden)

Mari Vainionpää

2012-01-01

Full Text Available A total of 47 racing greyhounds were enrolled in this study on two race days (in July and September, resp. at a racetrack. Twelve of the dogs participated in the study on both days. Thermographic images were taken before and after each race. From the images, superficial temperature points of selected sites (tendo calcaneus, musculus gastrocnemius, musculus gracilis, and musculus biceps femoris portio caudalis were taken and used to investigate the differences in superficial temperatures before and after the race. The thermographic images were compared between the right and left legs of a dog, between the raced distances, and between the two race days. The theoretical heat capacity of a racing greyhound was calculated. With regard to all distances raced, the superficial temperatures measured from the musculus gastrocnemius were significantly higher after the race than at baseline. No significant differences were found between the left and right legs of a dog after completing any of the distances. Significant difference was found between the two race days. The heat loss mechanisms of racing greyhounds during the race through forced conduction, radiation, evaporation, and panting can be considered adequate when observing the calculated heat capacity of the dogs.

Thermographic imaging of the superficial temperature in racing greyhounds before and after the race.

Science.gov (United States)

Vainionpää, Mari; Tienhaara, Esa-Pekka; Raekallio, Marja; Junnila, Jouni; Snellman, Marjatta; Vainio, Outi

2012-01-01

A total of 47 racing greyhounds were enrolled in this study on two race days (in July and September, resp.) at a racetrack. Twelve of the dogs participated in the study on both days. Thermographic images were taken before and after each race. From the images, superficial temperature points of selected sites (tendo calcaneus, musculus gastrocnemius, musculus gracilis, and musculus biceps femoris portio caudalis) were taken and used to investigate the differences in superficial temperatures before and after the race. The thermographic images were compared between the right and left legs of a dog, between the raced distances, and between the two race days. The theoretical heat capacity of a racing greyhound was calculated. With regard to all distances raced, the superficial temperatures measured from the musculus gastrocnemius were significantly higher after the race than at baseline. No significant differences were found between the left and right legs of a dog after completing any of the distances. Significant difference was found between the two race days. The heat loss mechanisms of racing greyhounds during the race through forced conduction, radiation, evaporation, and panting can be considered adequate when observing the calculated heat capacity of the dogs.

Sensor-Topology Based Simplicial Complex Reconstruction from Mobile Laser Scanning

Science.gov (United States)

Guinard, S.; Vallet, B.

2018-05-01

We propose a new method for the reconstruction of simplicial complexes (combining points, edges and triangles) from 3D point clouds from Mobile Laser Scanning (MLS). Our main goal is to produce a reconstruction of a scene that is adapted to the local geometry of objects. Our method uses the inherent topology of the MLS sensor to define a spatial adjacency relationship between points. We then investigate each possible connexion between adjacent points and filter them by searching collinear structures in the scene, or structures perpendicular to the laser beams. Next, we create triangles for each triplet of self-connected edges. Last, we improve this method with a regularization based on the co-planarity of triangles and collinearity of remaining edges. We compare our results to a naive simplicial complexes reconstruction based on edge length.

Fluid flow in panel radiator under various conditions - thermographic visualisation

Directory of Open Access Journals (Sweden)

Bašta Jiří

2012-04-01

Full Text Available Thermographic investigation of a heating panel radiator under various conditions, especially with various heating water volume flow rate is described in this article. For a radiator type 10-500x1000 TBOE and for two levels of inlet water temperature (75 and 55 °C a set of thermal images of surface temperature patterns for various values of heating water volume flow rate was taken. The initial value of flow rate was derived from nominal heating output and recalculated to real conditions. An increase of volume flow rate higher than 15 % over the nominal recalculated value is for the studied cases easily detectable on the resulting thermal images.

SENSOR-TOPOLOGY BASED SIMPLICIAL COMPLEX RECONSTRUCTION FROM MOBILE LASER SCANNING

Directory of Open Access Journals (Sweden)

S. Guinard

2018-05-01

Full Text Available We propose a new method for the reconstruction of simplicial complexes (combining points, edges and triangles from 3D point clouds from Mobile Laser Scanning (MLS. Our main goal is to produce a reconstruction of a scene that is adapted to the local geometry of objects. Our method uses the inherent topology of the MLS sensor to define a spatial adjacency relationship between points. We then investigate each possible connexion between adjacent points and filter them by searching collinear structures in the scene, or structures perpendicular to the laser beams. Next, we create triangles for each triplet of self-connected edges. Last, we improve this method with a regularization based on the co-planarity of triangles and collinearity of remaining edges. We compare our results to a naive simplicial complexes reconstruction based on edge length.

Recognition and Reconstruction of Zebra Crossings on Roads from Mobile Laser Scanning Data

Directory of Open Access Journals (Sweden)

Lin Li

2016-07-01

Full Text Available Zebra crossings provide guidance and warning to pedestrians and drivers, thereby playing an important role in traffic safety management. Most previous studies have focused on detecting zebra stripes but have not provided full information about the areas, which is critical to both driver assistance systems and guide systems for blind individuals. This paper presents a stepwise procedure for recognizing and reconstructing zebra crossings using mobile laser scanning data. First, we propose adaptive thresholding based on road surface partitioning to reduce the impact of intensity unevenness and improve the accuracy of road marking extraction. Then, dispersion degree filtering is used to reduce the noise. Finally, zebra stripes are recognized according to the rectangular feature and fixed size, which is followed by area reconstruction according to arrangement patterns. We test our method on three datasets captured by an Optech Lynx mobile mapping system. The total recognition rate of 90.91% demonstrates the effectiveness of the method.

A Greedy Scanning Data Collection Strategy for Large-Scale Wireless Sensor Networks with a Mobile Sink.

Science.gov (United States)

Zhu, Chuan; Zhang, Sai; Han, Guangjie; Jiang, Jinfang; Rodrigues, Joel J P C

2016-09-06

Mobile sink is widely used for data collection in wireless sensor networks. It can avoid 'hot spot' problems but energy consumption caused by multihop transmission is still inefficient in real-time application scenarios. In this paper, a greedy scanning data collection strategy (GSDCS) is proposed, and we focus on how to reduce routing energy consumption by shortening total length of routing paths. We propose that the mobile sink adjusts its trajectory dynamically according to the changes of network, instead of predetermined trajectory or random walk. Next, the mobile sink determines which area has more source nodes, then it moves toward this area. The benefit of GSDCS is that most source nodes are no longer needed to upload sensory data for long distances. Especially in event-driven application scenarios, when event area changes, the mobile sink could arrive at the new event area where most source nodes are located currently. Hence energy can be saved. Analytical and simulation results show that compared with existing work, our GSDCS has a better performance in specific application scenarios.

Characterization of Photovoltaic Panels by means of Thermograph Analysis

Directory of Open Access Journals (Sweden)

Noe Samano

2016-01-01

Full Text Available Solar panels have become attractive in order to generate and supply electricity in commercial and residential applications. Their increased module efficiencies have caused not only a massive production but also a sensible drop on sale prices. Methods of characterization, instrumentation for in situ measurements, defect monitoring, process control, and performance are required. A temperature characterization method by means of thermograph analysis is exposed in this paper. The method was applied to multicrystalline modules, and the characterization was made with respect to two different variables, first a thermal transient and second a characterization with respect to the current. The method is useful in order to detect hot spots caused by mismatch conditions in electrical parameters. The description, results, and limitations of the proposed method are discussed.

Compact Multipurpose Mobile Laser Scanning System — Initial Tests and Results

Directory of Open Access Journals (Sweden)

Craig Glennie

2013-01-01

Full Text Available We describe a prototype compact mobile laser scanning system that may be operated from a backpack or unmanned aerial vehicle. The system is small, self-contained, relatively inexpensive, and easy to deploy. A description of system components is presented, along with the initial calibration of the multi-sensor platform. The first field tests of the system, both in backpack mode and mounted on a helium balloon for real-world applications are presented. For both field tests, the acquired kinematic LiDAR data are compared with highly accurate static terrestrial laser scanning point clouds. These initial results show that the vertical accuracy of the point cloud for the prototype system is approximately 4 cm (1σ in balloon mode, and 3 cm (1σ in backpack mode while horizontal accuracy was approximately 17 cm (1σ for the balloon tests. Results from selected study areas on the Sacramento River Delta and San Andreas Fault in California demonstrate system performance, deployment agility and flexibility, and potential for operational production of high density and highly accurate point cloud data. Cost and production rate trade-offs place this system in the niche between existing airborne and tripod mounted LiDAR systems.

Maritime Laser Scanning as the Source for Spatial Data

Directory of Open Access Journals (Sweden)

Szulwic Jakub

2015-12-01

Full Text Available The rapid development of scanning technology, especially mobile scanning, gives the possibility to collect spatial data coming from maritime measurement platforms and autonomous manned or unmanned vehicles. Presented solution is derived from the mobile scanning. However we should keep in mind that the specificity of laser scanning at sea and processing collected data should be in the form acceptable in Geographical Information Systems, especially typical for the maritime needs. At the same time we should be aware that data coming from maritime mobile scanning constitutes a new approach to the describing of maritime environment and brings a new perspective that is completely different than air and terrestrial scanning.

Influencial factors in thermographic analysis in substations

Science.gov (United States)

Zarco-Periñán, Pedro J.; Martínez-Ramos, José L.

2018-05-01

Thermography is one of the best predictive maintenance tools available due to its low cost, fast implementation and effectiveness of the results obtained. The detected hot spots enable serious incidents to be prevented, both in the facilities and equipment where they have been located. In accordance with the criticality of such points, the repair is carried out with greater or lesser urgency. However, for detection to remain reliable, the facility must meet a set of requirements that are normally assumed, otherwise hot spots cannot be detected correctly and will subsequently cause unwanted defects. This paper analyses three aspects that influence the reliability of the results obtained: the minimum percentage of load that a circuit must contain in order to be able to locate all the hot spots therein; the minimum waiting time from when an item of equipment or facility is energized until a thermographic inspection can be carried out with a complete guarantee of hot spot detection; and the influence on the generation of hot spots exerted by the tightening torque realized in the assembly process.

Geometric validation of a mobile laser scanning system for urban applications

Science.gov (United States)

Guan, Haiyan; Li, Jonathan; Yu, Yongtao; Liu, Yan

2016-03-01

Mobile laser scanning (MLS) technologies have been actively studied and implemented over the past decade, as their application fields are rapidly expanding and extending beyond conventional topographic mapping. Trimble's MX-8, as one of the MLS systems in the current market, generates rich survey-grade laser and image data for urban surveying. The objective of this study is to evaluate whether Trimble MX-8 MLS data satisfies the accuracy requirements of urban surveying. According to the formula of geo-referencing, accuracies of navigation solution and laser scanner determines the accuracy of the collected LiDAR point clouds. Two test sites were selected to test the performance of Trimble MX-8. Those extensive tests confirm that Trimble MX-8 offers a very promising tool to survey complex urban areas.

Results of the survey activities and mobile gamma scanning in Monticello, Utah

International Nuclear Information System (INIS)

Little, C.A.; Berven, B.A.

1985-11-01

The town of Monticello, Utah, was once the site of an active mill which processed vanadium ore (1942 to 1948), and uranium ore (1948 to 1960). Properties in the vicinity of that mill have become contaminated with radioactive material from ore processing. The Radiological Survey Activities (RASA) group at Oak Ridge National Laboratory (ORNL) was requested by the Division of Remedial Action Projects (DRAP) in the Department of Energy (DOE) to: (1) identify potentially contaminated properties; (2) assess natural background radiation levels; and (3) rapidly assess the magnitude, extent, and type (i.e. ore, tailings, etc.) of contamination present on these properties (if any). This survey was conducted by RASA during April 1983. In addition to the 114 properties previously identified from historical information, the ORNL mobile gamma scanning van located 36 new properties exhibiting anomalous gamma radiation levels. Onsite surveys were conducted on 145 of the 150 total properties identified either historically or with the gamma scanning van. Of these 145 properties, 122 of them appeared to have some type of contaminated material present on them; however, only 48 appeared to be contaminated to the extent where they were in excess of Environmental Protection Agency (EPA) criteria (40 CFR 192). Twenty-one other properties were recommended for additional investigation (indoor gamma scanning and radon daughter measurements); of these, only ten required further analysis. This report provides the detailed data and analyses related to the radiological survey efforts performed by ORNL in Monticello, Utah

Thermographic method for evaluation of thermal influence of exterior surface colour of buildings

Science.gov (United States)

Wu, Yanpeng; Li, Deying; Jin, Rendong; Liu, Li; Bai, Jiabin; Feng, Jianming

2008-12-01

Architecture colour is an important part in urban designing. It directly affects the expressing and the thermal effect of exterior surface of buildings. It has proved that four factors affect the sign visibility, graphics, colour, lighting condition and age of the observers, and colour is the main aspect. The best method is to prevent the exterior space heating up in the first place, by reflecting heat away room the exterior surface.The colour of paint to coat building's exterior wall can have a huge impact on energy efficiency. While the suitable colour is essential to increasing the energy efficiency of paint colour during the warm summer months, those products also help paint colour efficiency and reduce heat loss from buildings during winter months making the interior more comfortable all year long. The article is based on analyzing the importance of architecture color design and existing urban colour design. The effect of external surface colour on the thermal behaviour of a building has been studied experimentally by Infrared Thermographic method in University of Science and technology Beijing insummer.The experimental results showed that different colour has quietly different thermal effect on the exterior surface of buildings. The thermal effect of carmine and fawn has nearly the same values. The main factor which is color express, give some suggest ting about urban color design. The investigation reveals that the use of suitable surface colour can dramatically reduce maximum the temperatures of the exterior wall. Keywords: architectural colour, thermal, thermographic

Classification of Mobile Laser Scanning Point Clouds from Height Features

Science.gov (United States)

Zheng, M.; Lemmens, M.; van Oosterom, P.

2017-09-01

The demand for 3D maps of cities and road networks is steadily growing and mobile laser scanning (MLS) systems are often the preferred geo-data acquisition method for capturing such scenes. Because MLS systems are mounted on cars or vans they can acquire billions of points of road scenes within a few hours of survey. Manual processing of point clouds is labour intensive and thus time consuming and expensive. Hence, the need for rapid and automated methods for 3D mapping of dense point clouds is growing exponentially. The last five years the research on automated 3D mapping of MLS data has tremendously intensified. In this paper, we present our work on automated classification of MLS point clouds. In the present stage of the research we exploited three features - two height components and one reflectance value, and achieved an overall accuracy of 73 %, which is really encouraging for further refining our approach.

Evaluation of the udder health status in subclinical mastitis affected dairy cows through bacteriological culture, somatic cell count and thermographic imaging.

Science.gov (United States)

Bortolami, A; Fiore, E; Gianesella, M; Corrò, M; Catania, S; Morgante, M

2015-01-01

Subclinical mastitis in dairy cows is a big economic loss for farmers. The monitoring of subclinical mastitis is usually performed through Somatic Cell Count (SCC) in farm but there is the need of new diagnostic systems able to quickly identify cows affected by subclinical infections of the udder. The aim of this study was to evaluate the potential application of thermographic imaging compared to SCC and bacteriological culture for infection detection in cow affected by subclinical mastitis and possibly to discriminate between different pathogens. In this study we evaluated the udder health status of 98 Holstein Friesian dairy cows with high SCC in 4 farms. From each cow a sample of milk was collected from all the functional quarters and submitted to bacteriological culture, SCC and Mycoplasma spp. culture. A thermographic image was taken from each functional udder quarter and nipple. Pearson's correlations and Analysis of Variance were performed in order to evaluate the different diagnostic techniques. The most frequent pathogen isolated was Staphylococcus aureus followed by Coagulase Negative Staphylococci (CNS), Streptococcus uberis, Streptococcus agalactiae and others. The Somatic Cell Score (SCS) was able to discriminate (pnegative at the bacteriological culture except for cows with infection caused by CNS. Infrared thermography was correlated to SCS (pnegative cows. Thermographic imaging seems to be promising in evaluating the inflammation status of cows affected by subclinical mastitis but seems to have a poor diagnostic value.

Automatic Feature Detection, Description and Matching from Mobile Laser Scanning Data and Aerial Imagery

Science.gov (United States)

Hussnain, Zille; Oude Elberink, Sander; Vosselman, George

2016-06-01

In mobile laser scanning systems, the platform's position is measured by GNSS and IMU, which is often not reliable in urban areas. Consequently, derived Mobile Laser Scanning Point Cloud (MLSPC) lacks expected positioning reliability and accuracy. Many of the current solutions are either semi-automatic or unable to achieve pixel level accuracy. We propose an automatic feature extraction method which involves utilizing corresponding aerial images as a reference data set. The proposed method comprise three steps; image feature detection, description and matching between corresponding patches of nadir aerial and MLSPC ortho images. In the data pre-processing step the MLSPC is patch-wise cropped and converted to ortho images. Furthermore, each aerial image patch covering the area of the corresponding MLSPC patch is also cropped from the aerial image. For feature detection, we implemented an adaptive variant of Harris-operator to automatically detect corner feature points on the vertices of road markings. In feature description phase, we used the LATCH binary descriptor, which is robust to data from different sensors. For descriptor matching, we developed an outlier filtering technique, which exploits the arrangements of relative Euclidean-distances and angles between corresponding sets of feature points. We found that the positioning accuracy of the computed correspondence has achieved the pixel level accuracy, where the image resolution is 12cm. Furthermore, the developed approach is reliable when enough road markings are available in the data sets. We conclude that, in urban areas, the developed approach can reliably extract features necessary to improve the MLSPC accuracy to pixel level.

Thermographic and microscopic evaluation of LARS knee ligament tearing.

Science.gov (United States)

Pătraşcu, Jenel Marian; Amarandei, Mihaela; Kun, Karla Noemy; Borugă, Ovidiu; Totorean, Alina; Andor, Bogdan; Florescu, Sorin

2014-01-01

Damage to knee articular ligaments causes important functional problems and adversely affects particularly the stability of the knee joint. Several methods were developed in order to repair damage to the anterior cruciate ligament (ACL), which employ autografts, allografts, as well as synthetic ligaments. One such synthetic scaffold, the ligament advanced reinforcement system (LARS) synthetic ligament is made of non-absorbing polyethylene terephthalate fibers whose structure allow tissue ingrowths in the intra-articular part, improving the stability of the joint. The LARS ligament is nowadays widely used in modern knee surgery in the Europe, Canada, China or Japan. This paper evaluates LARS ligament from two perspectives. The first regards a study done by the Orthopedics Clinic II, Timisoara, Romania, which compared results obtained by employing two techniques of ACL repair - the Bone-Tendon-Bone (BTB) or LARS arthroscopic, intra-articular techniques. This study found that patients treated with the BTB technique presented with an IKDC score of 45.82±1.14 units preoperative, with increasing values in the first nine months after each implant post-surgical ligament restoration, reaching an average value of 75.92 ± 2.88 units postoperative. Patients treated with the LARS technique presented with an IKDC score of 43.64 ± 1.11 units preoperative, and a score of 77.32 ± 2.71 units postoperative. The second perspective describes the thermographic and microscopic analysis of an artificial knee ligament tearing or loosening. The objective of the study was to obtain information regarding the design of artificial ligaments in order to expand their lifespan and avoid complications such as recurring synovitis, osteoarthritis and trauma of the knee joint. Thermographic data has shown that tearing begins from the inside out, thus improving the inner design of the ligament would probably enhance its durability. An optical microscope was employed to obtain images of structural

Thermographic image analysis for classification of ACL rupture disease, bone cancer, and feline hyperthyroid, with Gabor filters

Science.gov (United States)

Alvandipour, Mehrdad; Umbaugh, Scott E.; Mishra, Deependra K.; Dahal, Rohini; Lama, Norsang; Marino, Dominic J.; Sackman, Joseph

2017-05-01

Thermography and pattern classification techniques are used to classify three different pathologies in veterinary images. Thermographic images of both normal and diseased animals were provided by the Long Island Veterinary Specialists (LIVS). The three pathologies are ACL rupture disease, bone cancer, and feline hyperthyroid. The diagnosis of these diseases usually involves radiology and laboratory tests while the method that we propose uses thermographic images and image analysis techniques and is intended for use as a prescreening tool. Images in each category of pathologies are first filtered by Gabor filters and then various features are extracted and used for classification into normal and abnormal classes. Gabor filters are linear filters that can be characterized by the two parameters wavelength λ and orientation θ. With two different wavelength and five different orientations, a total of ten different filters were studied. Different combinations of camera views, filters, feature vectors, normalization methods, and classification methods, produce different tests that were examined and the sensitivity, specificity and success rate for each test were produced. Using the Gabor features alone, sensitivity, specificity, and overall success rates of 85% for each of the pathologies was achieved.

Tree Classification with Fused Mobile Laser Scanning and Hyperspectral Data

Science.gov (United States)

Puttonen, Eetu; Jaakkola, Anttoni; Litkey, Paula; Hyyppä, Juha

2011-01-01

Mobile Laser Scanning data were collected simultaneously with hyperspectral data using the Finnish Geodetic Institute Sensei system. The data were tested for tree species classification. The test area was an urban garden in the City of Espoo, Finland. Point clouds representing 168 individual tree specimens of 23 tree species were determined manually. The classification of the trees was done using first only the spatial data from point clouds, then with only the spectral data obtained with a spectrometer, and finally with the combined spatial and hyperspectral data from both sensors. Two classification tests were performed: the separation of coniferous and deciduous trees, and the identification of individual tree species. All determined tree specimens were used in distinguishing coniferous and deciduous trees. A subset of 133 trees and 10 tree species was used in the tree species classification. The best classification results for the fused data were 95.8% for the separation of the coniferous and deciduous classes. The best overall tree species classification succeeded with 83.5% accuracy for the best tested fused data feature combination. The respective results for paired structural features derived from the laser point cloud were 90.5% for the separation of the coniferous and deciduous classes and 65.4% for the species classification. Classification accuracies with paired hyperspectral reflectance value data were 90.5% for the separation of coniferous and deciduous classes and 62.4% for different species. The results are among the first of their kind and they show that mobile collected fused data outperformed single-sensor data in both classification tests and by a significant margin. PMID:22163894

AN AUTOMATED ROAD ROUGHNESS DETECTION FROM MOBILE LASER SCANNING DATA

Directory of Open Access Journals (Sweden)

P. Kumar

2017-05-01

Full Text Available Rough roads influence the safety of the road users as accident rate increases with increasing unevenness of the road surface. Road roughness regions are required to be efficiently detected and located in order to ensure their maintenance. Mobile Laser Scanning (MLS systems provide a rapid and cost-effective alternative by providing accurate and dense point cloud data along route corridor. In this paper, an automated algorithm is presented for detecting road roughness from MLS data. The presented algorithm is based on interpolating smooth intensity raster surface from LiDAR point cloud data using point thinning process. The interpolated surface is further processed using morphological and multi-level Otsu thresholding operations to identify candidate road roughness regions. The candidate regions are finally filtered based on spatial density and standard deviation of elevation criteria to detect the roughness along the road surface. The test results of road roughness detection algorithm on two road sections are presented. The developed approach can be used to provide comprehensive information to road authorities in order to schedule maintenance and ensure maximum safety conditions for road users.

An Automated Road Roughness Detection from Mobile Laser Scanning Data

Science.gov (United States)

Kumar, P.; Angelats, E.

2017-05-01

Rough roads influence the safety of the road users as accident rate increases with increasing unevenness of the road surface. Road roughness regions are required to be efficiently detected and located in order to ensure their maintenance. Mobile Laser Scanning (MLS) systems provide a rapid and cost-effective alternative by providing accurate and dense point cloud data along route corridor. In this paper, an automated algorithm is presented for detecting road roughness from MLS data. The presented algorithm is based on interpolating smooth intensity raster surface from LiDAR point cloud data using point thinning process. The interpolated surface is further processed using morphological and multi-level Otsu thresholding operations to identify candidate road roughness regions. The candidate regions are finally filtered based on spatial density and standard deviation of elevation criteria to detect the roughness along the road surface. The test results of road roughness detection algorithm on two road sections are presented. The developed approach can be used to provide comprehensive information to road authorities in order to schedule maintenance and ensure maximum safety conditions for road users.

A Mobile Automated Tomographic Gamma Scanning System - 13231

Energy Technology Data Exchange (ETDEWEB)

Kirkpatrick, J.M.; LeBlanc, P.J.; Nakazawa, D.; Petroka, D.L.; Kane Smith, S.; Venkataraman, R.; Villani, M. [Canberra Industries, Inc. 800 Research Parkway, Meriden CT 06450 (United States)

2013-07-01

Canberra Industries have recently designed and built a new automated Tomographic Gamma Scanning (TGS) system for mobile deployment. The TGS technique combines high-resolution gamma spectroscopy with low spatial resolution 3-dimensional image reconstruction to provide increased accuracy over traditional approaches for the assay of non-uniform source distributions in low-to medium-density, non-heterogeneous matrices. Originally pioneered by R. Estep at Los Alamos National Laboratory (LANL), the TGS method has been further developed and commercialized by Canberra Industries in recent years. The present system advances the state of the art on several fronts: it is designed to be housed in a standard cargo transport container for ease of transport, allowing waste characterization at multiple facilities under the purview of a single operator. Conveyor feed, drum rotator, and detector and collimator positioning mechanisms operated by programmable logic control (PLC) allow automated batch mode operation. The variable geometry settings can accommodate a wide range of waste packaging, including but not limited to standard 220 liter drums, 380 liter overpack drums, and smaller 20 liter cans. A 20 mCi Eu-152 transmission source provides attenuation corrections for drum matrices up to 1 g/cm{sup 3} in TGS mode; the system can be operated in Segmented Gamma Scanning (SGS) mode to measure higher density drums. To support TGS assays at higher densities, the source shield is sufficient to house an alternate Co-60 transmission source of higher activity, up to 250 mCi. An automated shutter and attenuator assembly is provided for operating the system with a dual intensity transmission source. The system's 1500 kg capacity rotator turntable can handle heavy containers such as concrete lined 380 liter overpack drums. Finally, data acquisition utilizes Canberra's Broad Energy Germanium (BEGE) detector and Lynx MCA, with 32 k channels, providing better than 0.1 ke

Use of thermographic imaging in clinical diagnosis of small animal: preliminary notes

Directory of Open Access Journals (Sweden)

Veronica Redaelli

2014-06-01

Full Text Available INTRODUCTION. The authors, after a description of the physics of infrared thermographic technique (IRT, analyze the reading of images and the main applications in the veterinary field, compared to the existing literature on the subject and to their experimental researches. IRT lends itself to countless applications in biology, thanks to its characteristics of versatility, lack of invasiveness and high sensitivity. Probably the major limitation to its application in the animal lies in the ease of use and in its extreme sensitivity. MATERIALS AND METHODS. From September 2009 to October 2010, the experimental investigation with the thermo camera took into consideration 110 animals (92 dogs and 18 cats, without any selection criteria. All patients were brought to the Faculty of Veterinary Medicine in Milan University by the owner, to be examined by a specialist, or to undergo one of the following diagnostic procedures: X-rays, computed tomography, or ultrasound examinations; finally some patients were brought in for surgical procedures. With the consent of the owner, 1 to 10 thermographic images were recorded from each clinical case. Results. In this first experimental investigation, thermography has shown a high sensitivity (100%, but a low specificity (44%. This figure excludes the use of thermal imaging technology to replace other imaging techniques such as radiography, computed tomography and magnetic resonance imaging. Furthermore, it does not show any ability to recognize the etiology of the disease, but only the thermal alteration, and this is restricting its use. However, this experimental study has demonstrated that thermography can be used in veterinary medicine, and specifically in dogs and cats. It is hoped that in the field of targeted diseases this technique will become an important tool for diagnostic purposes by using working protocols validated and repeatable.

Mobile gamma-ray scanning system for detecting radiation anomalies associated with 226Ra-bearing materials

International Nuclear Information System (INIS)

Myrick, T.E.; Blair, M.S.; Doane, R.W.; Goldsmith, W.A.

1982-11-01

A mobile gamma-ray scanning system has been developed by Oak Ridge National Laboratory for use in the Department of Energy's remedial action survey programs. The unit consists of a NaI(T1) detection system housed in a specially-equipped van. The system is operator controlled through an on-board mini-computer, with data output provided on the computer video screen, strip chart recorders, and an on-line printer. Data storage is provided by a floppy disk system. Multichannel analysis capabilities are included for qualitative radionuclide identification. A 226 Ra-specific algorithm is employed to identify locations containing residual radium-bearing materials. This report presents the details of the system description, software development, and scanning methods utilized with the ORNL system. Laboratory calibration and field testing have established the system sensitivity, field of view, and other performance characteristics, the results of which are also presented. Documentation of the instrumentation and computer programs are included

Using thermographic cameras to investigate eye temperature and clinical severity in depression

Science.gov (United States)

Maller, Jerome J.; George, Shefin Sam; Viswanathan, Rekha Puzhavakkathumadom; Fitzgerald, Paul B.; Junor, Paul

2016-02-01

Previous studies suggest that altered corneal temperature may be a feature of schizophrenia, but the association between major depressive disorder (MDD) and corneal temperature has yet to be assessed. The aim of this study is to investigate whether eye temperature is different among MDD patients than among healthy individuals. We used a thermographic camera to measure and compare the temperature profile across the corneas of 16 patients with MDD and 16 age- and sex-matched healthy subjects. We found that the average corneal temperature between the two groups did not differ statistically, although clinical severity correlated positively with right corneal temperature. Corneal temperature may be an indicator of clinical severity in psychiatric disorders, including depression.

Robust Locally Weighted Regression For Ground Surface Extraction In Mobile Laser Scanning 3D Data

Directory of Open Access Journals (Sweden)

A. Nurunnabi

2013-10-01

Full Text Available A new robust way for ground surface extraction from mobile laser scanning 3D point cloud data is proposed in this paper. Fitting polynomials along 2D/3D points is one of the well-known methods for filtering ground points, but it is evident that unorganized point clouds consist of multiple complex structures by nature so it is not suitable for fitting a parametric global model. The aim of this research is to develop and implement an algorithm to classify ground and non-ground points based on statistically robust locally weighted regression which fits a regression surface (line in 2D by fitting without any predefined global functional relation among the variables of interest. Afterwards, the z (elevation-values are robustly down weighted based on the residuals for the fitted points. The new set of down weighted z-values along with x (or y values are used to get a new fit of the (lower surface (line. The process of fitting and down-weighting continues until the difference between two consecutive fits is insignificant. Then the final fit represents the ground level of the given point cloud and the ground surface points can be extracted. The performance of the new method has been demonstrated through vehicle based mobile laser scanning 3D point cloud data from urban areas which include different problematic objects such as short walls, large buildings, electric poles, sign posts and cars. The method has potential in areas like building/construction footprint determination, 3D city modelling, corridor mapping and asset management.

LARGE SCALE TEXTURED MESH RECONSTRUCTION FROM MOBILE MAPPING IMAGES AND LIDAR SCANS

Directory of Open Access Journals (Sweden)

M. Boussaha

2018-05-01

Full Text Available The representation of 3D geometric and photometric information of the real world is one of the most challenging and extensively studied research topics in the photogrammetry and robotics communities. In this paper, we present a fully automatic framework for 3D high quality large scale urban texture mapping using oriented images and LiDAR scans acquired by a terrestrial Mobile Mapping System (MMS. First, the acquired points and images are sliced into temporal chunks ensuring a reasonable size and time consistency between geometry (points and photometry (images. Then, a simple, fast and scalable 3D surface reconstruction relying on the sensor space topology is performed on each chunk after an isotropic sampling of the point cloud obtained from the raw LiDAR scans. Finally, the algorithm proposed in (Waechter et al., 2014 is adapted to texture the reconstructed surface with the images acquired simultaneously, ensuring a high quality texture with no seams and global color adjustment. We evaluate our full pipeline on a dataset of 17 km of acquisition in Rouen, France resulting in nearly 2 billion points and 40000 full HD images. We are able to reconstruct and texture the whole acquisition in less than 30 computing hours, the entire process being highly parallel as each chunk can be processed independently in a separate thread or computer.

Large Scale Textured Mesh Reconstruction from Mobile Mapping Images and LIDAR Scans

Science.gov (United States)

Boussaha, M.; Vallet, B.; Rives, P.

2018-05-01

The representation of 3D geometric and photometric information of the real world is one of the most challenging and extensively studied research topics in the photogrammetry and robotics communities. In this paper, we present a fully automatic framework for 3D high quality large scale urban texture mapping using oriented images and LiDAR scans acquired by a terrestrial Mobile Mapping System (MMS). First, the acquired points and images are sliced into temporal chunks ensuring a reasonable size and time consistency between geometry (points) and photometry (images). Then, a simple, fast and scalable 3D surface reconstruction relying on the sensor space topology is performed on each chunk after an isotropic sampling of the point cloud obtained from the raw LiDAR scans. Finally, the algorithm proposed in (Waechter et al., 2014) is adapted to texture the reconstructed surface with the images acquired simultaneously, ensuring a high quality texture with no seams and global color adjustment. We evaluate our full pipeline on a dataset of 17 km of acquisition in Rouen, France resulting in nearly 2 billion points and 40000 full HD images. We are able to reconstruct and texture the whole acquisition in less than 30 computing hours, the entire process being highly parallel as each chunk can be processed independently in a separate thread or computer.

Thermographic measurements of high-speed metal cutting

Science.gov (United States)

Mueller, Bernhard; Renz, Ulrich

2002-03-01

Thermographic measurements of a high-speed cutting process have been performed with an infrared camera. To realize images without motion blur the integration times were reduced to a few microseconds. Since the high tool wear influences the measured temperatures a set-up has been realized which enables small cutting lengths. Only single images have been recorded because the process is too fast to acquire a sequence of images even with the frame rate of the very fast infrared camera which has been used. To expose the camera when the rotating tool is in the middle of the camera image an experimental set-up with a light barrier and a digital delay generator with a time resolution of 1 ns has been realized. This enables a very exact triggering of the camera at the desired position of the tool in the image. Since the cutting depth is between 0.1 and 0.2 mm a high spatial resolution was also necessary which was obtained by a special close-up lens allowing a resolution of app. 45 microns. The experimental set-up will be described and infrared images and evaluated temperatures of a titanium alloy and a carbon steel will be presented for cutting speeds up to 42 m/s.

Roadside Multiple Objects Extraction from Mobile Laser Scanning Point Cloud Based on DBN

Directory of Open Access Journals (Sweden)

LUO Haifeng

2018-02-01

Full Text Available This paper proposed an novel algorithm for exploring deep belief network (DBN architectures to extract and recognize roadside facilities (trees,cars and traffic poles from mobile laser scanning (MLS point cloud.The proposed methods firstly partitioned the raw MLS point cloud into blocks and then removed the ground and building points.In order to partition the off-ground objects into individual objects,off-ground points were organized into an Octree structure and clustered into candidate objects based on connected component.To improve segmentation performance on clusters containing overlapped objects,a refining processing using a voxel-based normalized cut was then implemented.In addition,multi-view features descriptor was generated for each independent roadside facilities based on binary images.Finally,a deep belief network (DBN was trained to extract trees,cars and traffic pole objects.Experiments are undertaken to evaluate the validities of the proposed method with two datasets acquired by Lynx Mobile Mapper System.The precision of trees,cars and traffic poles objects extraction results respectively was 97.31%,97.79% and 92.78%.The recall was 98.30%,98.75% and 96.77% respectively.The quality is 95.70%,93.81% and 90.00%.And the F1 measure was 97.80%,96.81% and 94.73%.

Results of the mobile gamma scanning activities in Wayne and Pequannock Townships, New Jersey

International Nuclear Information System (INIS)

Johnson, C.A.; Roberts, D.A.; Patania, V.P.; Foley, R.D.

1994-01-01

During the early 1980s the W. R. Grace site and the adjacent area were the focus of several radiological investigations. Radiological surveys revealed surface radionuclide concentrations greater than those acceptable under US Department of Energy (DOE) remedial action guidelines. In 1984, Congress assigned responsibility for cleanup of the W.R. Grace site to the Department of Energy. The property was redesignated as the Wayne Interim Storage Site (WISS) and in 1985 DOE began plans for survey/monitoring, and remedial action of nearby vicinity properties and the interim storage site. Evaluations of the radiological survey data in 1986 indicated radioactive contamination above current DOE guidelines at the off-site areas of parts of Township Park southwest of WISS, and parts of the Sheffield Brook area and railroad siding in Pequannock Township. Remedial action was conducted over several years of most of these areas and independent verification of remedial action was performed. A team from Oak Ridge National Laboratory conducted a mobile radiological scanning survey of a stretch of public roadway in the immediate vicinity south of the WISS, extending northwest to the Pompton turnpike. A mobile gamma scanning van with an on-board computer system was used to identify at least 24 anomalous areas, some attributable to the naturally elevated levels in concrete, asphalt, and natural granite found in streets, driveways and landscaping materials in the area. Analyses of the biased soil samples taken in the ballpark also revealed slightly elevated thorium concentrations. However, soil concentration measurements when averaged over 100 m 2 fall below the limits prescribed by DOE radiological guidelines established for this site. The anomalies may result from a wide range of sources, such as ash, granite, and fertilizer as well as materials from the former Grace facility

Extraction of Vertical Walls from Mobile Laser Scanning Data for Solar Potential Assessment

Directory of Open Access Journals (Sweden)

Martin Rutzinger

2011-03-01

Full Text Available In recent years there has been an increasing demand among home owners for cost effective sustainable energy production such as solar energy to provide heating and electricity. A lot of research has focused on the assessment of the incoming solar radiation on roof planes acquired by, e.g., Airborne Laser Scanning (ALS. However, solar panels can also be mounted on building facades in order to increase renewable energy supply. Due to limited reflections of points from vertical walls, ALS data is not suitable to perform solar potential assessment of vertical building facades. This paper focuses on a new method for automatic solar radiation modeling of facades acquired by Mobile Laser Scanning (MLS and uses the full 3D information of the point cloud for both the extraction of vertical walls covered by the survey and solar potential analysis. Furthermore, a new method isintroduced determining the interior and exterior face, respectively, of each detected wall in order to calculate its slope and aspect angles that are of crucial importance for solar potential assessment. Shadowing effects of nearby objects are considered by computing the 3D horizon of each point of a facade segment within the 3D point cloud.

Time-averaged probability density functions of soot nanoparticles along the centerline of a piloted turbulent diffusion flame using a scanning mobility particle sizer

KAUST Repository

Chowdhury, Snehaunshu; Boyette, Wesley; Roberts, William L.

2017-01-01

In this study, we demonstrate the use of a scanning mobility particle sizer (SMPS) as an effective tool to measure the probability density functions (PDFs) of soot nanoparticles in turbulent flames. Time-averaged soot PDFs necessary for validating

LIDAR AND INS FUSION IN PERIODS OF GPS OUTAGES FOR MOBILE LASER SCANNING MAPPING SYSTEMS

Directory of Open Access Journals (Sweden)

I. Klein

2012-09-01

Full Text Available Mobile laser scanning systems are becoming an increasingly popular means to obtain 3D coverage on a large scale. To perform the mapping, the exact position of the vehicle must be known throughout the trajectory. Exact position is achieved via integration of Global Positioning Systems (GPS and Inertial Navigation Systems (INS. Yet, in urban environments, cases of complete or even partial GPS outages may occur leaving the navigation solution to rely only on the INS. The INS navigation solution degrades with time as the Inertial Measurement Unit (IMU measurements contains noise, which permeates into the navigation equations. Degradation of the position determination leads to loss of data in such segments. To circumvent such drift and its effects, we propose fusing INS with lidar data by using building edges. This detection of edges is then translated into position data, which is used as an aiding to the INS. It thereby enables the determination of the vehicle position with a satisfactory level accuracy, sufficient to perform the laser-scanning based mapping in those outage periods.

Hierarchical extraction of urban objects from mobile laser scanning data

Science.gov (United States)

Yang, Bisheng; Dong, Zhen; Zhao, Gang; Dai, Wenxia

2015-01-01

Point clouds collected in urban scenes contain a huge number of points (e.g., billions), numerous objects with significant size variability, complex and incomplete structures, and variable point densities, raising great challenges for the automated extraction of urban objects in the field of photogrammetry, computer vision, and robotics. This paper addresses these challenges by proposing an automated method to extract urban objects robustly and efficiently. The proposed method generates multi-scale supervoxels from 3D point clouds using the point attributes (e.g., colors, intensities) and spatial distances between points, and then segments the supervoxels rather than individual points by combining graph based segmentation with multiple cues (e.g., principal direction, colors) of the supervoxels. The proposed method defines a set of rules for merging segments into meaningful units according to types of urban objects and forms the semantic knowledge of urban objects for the classification of objects. Finally, the proposed method extracts and classifies urban objects in a hierarchical order ranked by the saliency of the segments. Experiments show that the proposed method is efficient and robust for extracting buildings, streetlamps, trees, telegraph poles, traffic signs, cars, and enclosures from mobile laser scanning (MLS) point clouds, with an overall accuracy of 92.3%.

PRE AND POSTPRANDIAL THERMOGRAPHIC PROFILE OF GREEN IGUANAS (IGUANA IGUANA

Directory of Open Access Journals (Sweden)

Simona Rusu

2016-11-01

Full Text Available Abstract The body temperature of 10 clinically healthy green iguanas (Iguana iguana was measured using a thermographic camera (FLIR E6, Flir Systems Sweden before and after the food was offered. For each animal there were performed a total of 6 measurements (3 before feeding and 3 after the food was offered. The purpose of this experiment was to observe the thermographic pattern of the body before and after the feeding, since herbivore reptiles tend to bask after the feeding to increase the body temperature that will help them afterwards digest the food. The animals were housed in individual vivariums with every animal having a basking spot available. The pictures were taken outside the vivarium in an adjacent room. The animals were handled with gloves and transported in a cardboard box in order to avoid heat transfer between the handler and the iguana that would have produced thermal artefacts. Each individual was placed on a table on a styrofoam slate, again, to avoid the heat transfer between the table and the animal`s body. For each animal a total of 4 pictures were taken (up, front, left and right. The pictures were analysed with the FLIR Tools program that is provided by the manufacturer and 3 temperatures were taken into consideration (the head temperature, body temperature on the right side and body temperature on the left side. The temperatures were compared between them and with the temperature of the vivariums that consisted of the average between the temperature in 3 different spots (basking spot, the feeding bowl site and the coldest spot measured with an infrared thermometer GM300 (Benetech, China. The temperature of the body was dependent on the vivarium temperature and it was a significant temperature difference between the measurements before the feeding and after the feeding. Also we discovered a significant difference between the head temperature and the body temperature on the left side before the feeding that disappeared

Street-side vehicle detection, classification and change detection using mobile laser scanning data

Science.gov (United States)

Xiao, Wen; Vallet, Bruno; Schindler, Konrad; Paparoditis, Nicolas

2016-04-01

Statistics on street-side car parks, e.g. occupancy rates, parked vehicle types, parking durations, are of great importance for urban planning and policy making. Related studies, e.g. vehicle detection and classification, mostly focus on static images or video. Whereas mobile laser scanning (MLS) systems are increasingly utilized for urban street environment perception due to their direct 3D information acquisition, high accuracy and movability. In this paper, we design a complete system for car park monitoring, including vehicle recognition, localization, classification and change detection, from laser scanning point clouds. The experimental data are acquired by an MLS system using high frequency laser scanner which scans the streets vertically along the system's moving trajectory. The point clouds are firstly classified as ground, building façade, and street objects which are then segmented using state-of-the-art methods. Each segment is treated as an object hypothesis, and its geometric features are extracted. Moreover, a deformable vehicle model is fitted to each object. By fitting an explicit model to the vehicle points, detailed information, such as precise position and orientation, can be obtained. The model parameters are also treated as vehicle features. Together with the geometric features, they are applied to a supervised learning procedure for vehicle or non-vehicle recognition. The classes of detected vehicles are also investigated. Whether vehicles have changed across two datasets acquired at different times is detected to estimate the durations. Here, vehicles are trained pair-wisely. Two same or different vehicles are paired up as training samples. As a result, the vehicle recognition, classification and change detection accuracies are 95.9%, 86.0% and 98.7%, respectively. Vehicle modelling improves not only the recognition rate, but also the localization precision compared to bounding boxes.

Automated system for crack detection using infrared thermograph

International Nuclear Information System (INIS)

Starman, Stanislav

2009-01-01

The objective of this study was the development of the automated system for crack detection on square steel bars used in the automotive industry for axle and shaft construction. The automated system for thermographic crack detection uses brief pulsed eddy currents to heat steel components under inspection. Cracks, if present, will disturb the current flow and so generate changes in the temperature profile in the crack area. These changes of temperature are visualized using an infrared camera. The image acquired by the infrared camera is evaluated through an image processing system. The advantages afforded by the system are its inspection time, its excellent flaw detection sensitivity and its ability to detect hidden, subsurface cracks. The automated system consists of four IR cameras (each side of steel bar is evaluated at a time), coil, high frequency generator and control place with computers. The system is a part of the inspection line where the subsurface and surface cracks are searched. If the crack is present, the cracked place is automatically marked. The components without cracks are then deposited apart from defective blocks. The system is fully automated and its ability is to evaluate four meter blocks within 20 seconds. This is the real reason for using this system in real industrial applications. (author)

Performance analysis of a compact and low-cost mapping-grade mobile laser scanning system

Science.gov (United States)

Julge, Kalev; Vajakas, Toivo; Ellmann, Artu

2017-10-01

The performance of a low-cost, self-contained, compact, and easy to deploy mapping-grade mobile laser scanning (MLS) system, which is composed of a light detection and ranging sensor Velodyne VLP-16 and a dual antenna global navigation satellite system/inertial navigation system SBG Systems Ellipse-D, is analyzed. The field tests were carried out in car-mounted and backpack modes for surveying road engineering structures (such as roads, parking lots, underpasses, and tunnels) and coastal erosion zones, respectively. The impact of applied calculation principles on trajectory postprocessing, direct georeferencing, and the theoretical accuracy of the system is analyzed. A calibration method, based on Bound Optimization BY Quadratic Approximation, for finding the boresight angles of an MLS system is proposed. The resulting MLS point clouds are compared with high-accuracy static terrestrial laser scanning data and survey-grade MLS data from a commercially manufactured MLS system. The vertical, horizontal, and relative accuracy are assessed-the root-mean-square error (RMSE) values were determined to be 8, 15, and 3 cm, respectively. Thus, the achieved mapping-grade accuracy demonstrates that this relatively compact and inexpensive self-assembled MLS can be successfully used for surveying the geometry and deformations of terrain, buildings, road, and other engineering structures.

Implementation of an Ultra-Bright Thermographic Phosphor for Gas Turbine Engine Temperature Measurements

Science.gov (United States)

Eldridge, Jeffrey I.; Bencic, Timothy J.; Zhu, Dongming; Cuy, Michael D.; Wolfe, Douglas E.; Allison, Stephen W.; Beshears, David L.; Jenkins, Thomas P.; Heeg, Bauke; Howard, Robert P.;

High Pressure Scanning Tunneling Microscopy Studies of AdsorbateStructure and Mobility during Catalytic Reactions: Novel Design of anUltra High Pressure, High Temperature Scanning Tunneling MicroscopeSystem for Probing Catalytic Conversions

Energy Technology Data Exchange (ETDEWEB)

Tang, David Chi-Wai [Univ. of California, Berkeley, CA (United States)

2005-05-16

The aim of the work presented therein is to take advantage of scanning tunneling microscope’s (STM) capability for operation under a variety of environments under real time and at atomic resolution to monitor adsorbate structures and mobility under high pressures, as well as to design a new generation of STM systems that allow imaging in situ at both higher pressures (35 atm) and temperatures (350 °C).

A Thermographic Measurement Approach to Assess Supercapacitor Electrical Performances

Directory of Open Access Journals (Sweden)

Stanislaw Galla

2017-12-01

Full Text Available This paper describes a proposal for the qualitative assessment of condition of supercapacitors based on the conducted thermographic measurements. The presented measurement stand was accompanied by the concept of methodology of performing tests. Necessary conditions, which were needed to minimize the influence of disturbing factors on the performance of thermal imaging measurements, were also indicated. Mentioned factors resulted from both: the hardware limitations and from the necessity to prepare samples. The algorithm that was used to determine the basic parameters for assessment has been presented. The article suggests to use additional factors that may facilitate the analysis of obtained results. Measuring the usefulness of the proposed methodology was tested on commercial samples of supercapacitors. All of the tests were taken in conjunction with the classical methods based on capacitance (C and equivalent series resistance (ESR measurements, which were also presented in the paper. Selected results presenting the observed changes occurring in both: basic parameters of supercapacitors and accompanying fluctuations of thermal fields, along with analysis, were shown. The observed limitations of the proposed assessment method and the suggestions for its development were also described.

Airborne eXpendable BathyThermographs (AXBT) data from Ocean Surveys in the Gulf of Mexico during Hurricane Lili 2002-10-02 to 2002-10-04 (NCEI Accession 0159386)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Airborne eXpendable BathyThermographs (AXBT) data from deployments during field operations to study Hurricane Lili. The data were used in model simulations for...

Fiber Optic Bragg Grating Sensors for Thermographic Detection of Subsurface Anomalies

Science.gov (United States)

Allison, Sidney G.; Winfree, William P.; Wu, Meng-Chou

2009-01-01

Conventional thermography with an infrared imager has been shown to be an extremely viable technique for nondestructively detecting subsurface anomalies such as thickness variations due to corrosion. A recently developed technique using fiber optic sensors to measure temperature holds potential for performing similar inspections without requiring an infrared imager. The structure is heated using a heat source such as a quartz lamp with fiber Bragg grating (FBG) sensors at the surface of the structure to detect temperature. Investigated structures include a stainless steel plate with thickness variations simulated by small platelets attached to the back side using thermal grease. A relationship is shown between the FBG sensor thermal response and variations in material thickness. For comparison, finite element modeling was performed and found to agree closely with the fiber optic thermography results. This technique shows potential for applications where FBG sensors are already bonded to structures for Integrated Vehicle Health Monitoring (IVHM) strain measurements and can serve dual-use by also performing thermographic detection of subsurface anomalies.

Automatic Extraction of Road Markings from Mobile Laser Scanning Data

Science.gov (United States)

Ma, H.; Pei, Z.; Wei, Z.; Zhong, R.

2017-09-01

Road markings as critical feature in high-defination maps, which are Advanced Driver Assistance System (ADAS) and self-driving technology required, have important functions in providing guidance and information to moving cars. Mobile laser scanning (MLS) system is an effective way to obtain the 3D information of the road surface, including road markings, at highway speeds and at less than traditional survey costs. This paper presents a novel method to automatically extract road markings from MLS point clouds. Ground points are first filtered from raw input point clouds using neighborhood elevation consistency method. The basic assumption of the method is that the road surface is smooth. Points with small elevation-difference between neighborhood are considered to be ground points. Then ground points are partitioned into a set of profiles according to trajectory data. The intensity histogram of points in each profile is generated to find intensity jumps in certain threshold which inversely to laser distance. The separated points are used as seed points to region grow based on intensity so as to obtain road mark of integrity. We use the point cloud template-matching method to refine the road marking candidates via removing the noise clusters with low correlation coefficient. During experiment with a MLS point set of about 2 kilometres in a city center, our method provides a promising solution to the road markings extraction from MLS data.

System for leaks inspection in a nuclear plant by means of a mobile robot

International Nuclear Information System (INIS)

Ramirez S, R.; Segovia de los Rios, J.A.

2004-01-01

In this work a supervision system that could allow to carry out the detection of leaks of vapor in pipe lines, using a mobile robot Pioneer 2 -D Xe, which is controlled by means of an external micro controller 68HC912B32 programmed in Forth and using diffuse control to travel a road by means of the one to follow one lines painted in the floor is described. The robot takes in his superior part, a thermographic camera that allows to determine if leaks of vapor exist in pipes and a dosemeter to measure the present radiation levels in the place, besides a video camera. This way, the personnel, can make sure of having a propitious situation to make the maintenance of the facilities. (Author)

A Low-Cost Environmental Monitoring System: How to Prevent Systematic Errors in the Design Phase through the Combined Use of Additive Manufacturing and Thermographic Techniques

Directory of Open Access Journals (Sweden)

Francesco Salamone

2017-04-01

Full Text Available nEMoS (nano Environmental Monitoring System is a 3D-printed device built following the Do-It-Yourself (DIY approach. It can be connected to the web and it can be used to assess indoor environmental quality (IEQ. It is built using some low-cost sensors connected to an Arduino microcontroller board. The device is assembled in a small-sized case and both thermohygrometric sensors used to measure the air temperature and relative humidity, and the globe thermometer used to measure the radiant temperature, can be subject to thermal effects due to overheating of some nearby components. A thermographic analysis was made to rule out this possibility. The paper shows how the pervasive technique of additive manufacturing can be combined with the more traditional thermographic techniques to redesign the case and to verify the accuracy of the optimized system in order to prevent instrumental systematic errors in terms of the difference between experimental and actual values of the above-mentioned environmental parameters.

A Low-Cost Environmental Monitoring System: How to Prevent Systematic Errors in the Design Phase through the Combined Use of Additive Manufacturing and Thermographic Techniques.

Science.gov (United States)

Salamone, Francesco; Danza, Ludovico; Meroni, Italo; Pollastro, Maria Cristina

2017-04-11

nEMoS (nano Environmental Monitoring System) is a 3D-printed device built following the Do-It-Yourself (DIY) approach. It can be connected to the web and it can be used to assess indoor environmental quality (IEQ). It is built using some low-cost sensors connected to an Arduino microcontroller board. The device is assembled in a small-sized case and both thermohygrometric sensors used to measure the air temperature and relative humidity, and the globe thermometer used to measure the radiant temperature, can be subject to thermal effects due to overheating of some nearby components. A thermographic analysis was made to rule out this possibility. The paper shows how the pervasive technique of additive manufacturing can be combined with the more traditional thermographic techniques to redesign the case and to verify the accuracy of the optimized system in order to prevent instrumental systematic errors in terms of the difference between experimental and actual values of the above-mentioned environmental parameters.

Efficient Signature Based Malware Detection on Mobile Devices

Directory of Open Access Journals (Sweden)

Deepak Venugopal

2008-01-01

Full Text Available The threat of malware on mobile devices is gaining attention recently. It is important to provide security solutions to these devices before these threats cause widespread damage. However, mobile devices have severe resource constraints in terms of memory and power. Hence, even though there are well developed techniques for malware detection on the PC domain, it requires considerable effort to adapt these techniques for mobile devices. In this paper, we outline the considerations for malware detection on mobile devices and propose a signature based malware detection method. Specifically, we detail a signature matching algorithm that is well suited for use in mobile device scanning due to its low memory requirements. Additionally, the matching algorithm is shown to have high scanning speed which makes it unobtrusive to users. Our evaluation and comparison study with the well known Clam-AV scanner shows that our solution consumes less than 50% of the memory used by Clam-AV while maintaining a fast scanning rate.

AUTOMATIC EXTRACTION OF ROAD MARKINGS FROM MOBILE LASER SCANNING DATA

Directory of Open Access Journals (Sweden)

H. Ma

2017-09-01

Full Text Available Road markings as critical feature in high-defination maps, which are Advanced Driver Assistance System (ADAS and self-driving technology required, have important functions in providing guidance and information to moving cars. Mobile laser scanning (MLS system is an effective way to obtain the 3D information of the road surface, including road markings, at highway speeds and at less than traditional survey costs. This paper presents a novel method to automatically extract road markings from MLS point clouds. Ground points are first filtered from raw input point clouds using neighborhood elevation consistency method. The basic assumption of the method is that the road surface is smooth. Points with small elevation-difference between neighborhood are considered to be ground points. Then ground points are partitioned into a set of profiles according to trajectory data. The intensity histogram of points in each profile is generated to find intensity jumps in certain threshold which inversely to laser distance. The separated points are used as seed points to region grow based on intensity so as to obtain road mark of integrity. We use the point cloud template-matching method to refine the road marking candidates via removing the noise clusters with low correlation coefficient. During experiment with a MLS point set of about 2 kilometres in a city center, our method provides a promising solution to the road markings extraction from MLS data.

A study of mammographic and thermographic findings in breast diseases

International Nuclear Information System (INIS)

Cho, Won Sik; Jeon, Woo Ki; Kim, Jeong Sook; Han, Chang Yul

1989-01-01

The ideal diagnostic methods in breast diseases consist of the physical examination and complementary radiologic examination. In radiologic examination mammography is the most popular screening methods and the older simple complementary method is thermography which is efficient under the conditions of elevated skin temperature in inflammatory and malignant lesions. From Jan. 1st 1987 through Jan. 30th, 1988, 110 pts. with complaints of mammary problems were examined by mammography and thermography at Paik Hospital, Inje University. The authors selected and analyzed 97 cases had been pathologically proved through the operation and the fine needle aspiration biopsy. The results were as follows: 1. The most prevalent age group was 5th decade (40%) in cancer, 4th decade (47%) in mammary dysplasia and followed by fibroadenoma (63%) in 4th decade. 2. The mammographic and thermographic findings were compared between the mammary dysplasia and the infiltrating ductal cancer. In mammary dysplasia abnormal hot emissions were appeared in 9/44 (17%) correlated with atypical hyperchromatic cytoplasm relates to pre-malignant group. 3. We hope and expect the early detection of breast cancer through the follow-up study in pre-malignant group of mammary dysplasia

DIGITAL TERRAIN MODELS FROM MOBILE LASER SCANNING DATA IN MORAVIAN KARST

Directory of Open Access Journals (Sweden)

N. Tyagur

2016-06-01

Full Text Available During the last ten years, mobile laser scanning (MLS systems have become a very popular and efficient technology for capturing reality in 3D. A 3D laser scanner mounted on the top of a moving vehicle (e.g. car allows the high precision capturing of the environment in a fast way. Mostly this technology is used in cities for capturing roads and buildings facades to create 3D city models. In our work, we used an MLS system in Moravian Karst, which is a protected nature reserve in the Eastern Part of the Czech Republic, with a steep rocky terrain covered by forests. For the 3D data collection, the Riegl VMX 450, mounted on a car, was used with integrated IMU/GNSS equipment, which provides low noise, rich and very dense 3D point clouds. The aim of this work is to create a digital terrain model (DTM from several MLS data sets acquired in the neighbourhood of a road. The total length of two covered areas is 3.9 and 6.1 km respectively, with an average width of 100 m. For the DTM generation, a fully automatic, robust, hierarchic approach was applied. The derivation of the DTM is based on combinations of hierarchical interpolation and robust filtering for different resolution levels. For the generation of the final DTMs, different interpolation algorithms are applied to the classified terrain points. The used parameters were determined by explorative analysis. All MLS data sets were processed with one parameter set. As a result, a high precise DTM was derived with high spatial resolution of 0.25 x 0.25 m. The quality of the DTMs was checked by geodetic measurements and visual comparison with raw point clouds. The high quality of the derived DTM can be used for analysing terrain changes and morphological structures. Finally, the derived DTM was compared with the DTM of the Czech Republic (DMR 4G with a resolution of 5 x 5 m, which was created from airborne laser scanning data. The vertical accuracy of the derived DTMs is around 0.10 m.

Bone Densitometry (Bone Density Scan)

Science.gov (United States)

... made of metal. Objects such as keys or wallets that would be in the area being scanned should be removed. You will ... and are often available in drugstores and on mobile health vans in the community. The pDEXA device is much smaller than ...

Feasibility and Limitations of Vaccine Two-Dimensional Barcoding Using Mobile Devices.

Science.gov (United States)

Bell, Cameron; Guerinet, Julien; Atkinson, Katherine M; Wilson, Kumanan

2016-06-23

Two-dimensional (2D) barcoding has the potential to enhance documentation of vaccine encounters at the point of care. However, this is currently limited to environments equipped with dedicated barcode scanners and compatible record systems. Mobile devices may present a cost-effective alternative to leverage 2D vaccine vial barcodes and improve vaccine product-specific information residing in digital health records. Mobile devices have the potential to capture product-specific information from 2D vaccine vial barcodes. We sought to examine the feasibility, performance, and potential limitations of scanning 2D barcodes on vaccine vials using 4 different mobile phones. A unique barcode scanning app was developed for Android and iOS operating systems. The impact of 4 variables on the scan success rate, data accuracy, and time to scan were examined: barcode size, curvature, fading, and ambient lighting conditions. Two experimenters performed 4 trials 10 times each, amounting to a total of 2160 barcode scan attempts. Of the 1832 successful scans performed in this evaluation, zero produced incorrect data. Five-millimeter barcodes were the slowest to scan, although only by 0.5 seconds on average. Barcodes with up to 50% fading had a 100% success rate, but success rate deteriorated beyond 60% fading. Curved barcodes took longer to scan compared with flat, but success rate deterioration was only observed at a vial diameter of 10 mm. Light conditions did not affect success rate or scan time between 500 lux and 20 lux. Conditions below 20 lux impeded the device's ability to scan successfully. Variability in scan time was observed across devices in all trials performed. 2D vaccine barcoding is possible using mobile devices and is successful under the majority of conditions examined. Manufacturers utilizing 2D barcodes should take into consideration the impact of factors that limit scan success rates. Future studies should evaluate the effect of mobile barcoding on workflow and

Thermographic visualization of the superficial vein and extravasation using the temperature gradient produced by the injected materials

Science.gov (United States)

Nakamura, Katsumasa; Sasaki, Tomonari; Ohga, Saiji; Yoshitake, Tadamasa; Terashima, Kotaro; Asai, Kaori; Matsumoto, Keiji; Shinoto, Makoto; Shioyama, Yoshiyuki; Nishie, Akihoro; Honda, Hiroshi

2014-11-01

There are few effective methods to detect or prevent the extravasation of injected materials such as chemotherapeutic agents and radiographic contrast materials. To investigate whether a thermographic camera could visualize the superficial vein and extravasation using the temperature gradient produced by the injected materials, an infrared thermographic camera with a high resolution of 0.04 °C was used. At the room temperature of 26 °C, thermal images and the time course of the temperature changes of a paraffin phantom embedded with rubber tubes (diameter 3.2 mm, wall thickness 0.8 mm) were evaluated after the tubes were filled with water at 15 °C or 25 °C. The rubber tubes were embedded at depths of 0 mm, 1.5 mm, and 3.0 mm from the surface of the phantom. Temperature changes were visualized in the areas of the phantom where the tubes were embedded. In general, changes were more clearly detected when greater temperature differences between the phantom and the water and shallower tube locations were employed. The temperature changes of the surface of a volunteer's arm were also examined after a bolus injection of physiological saline into the dorsal hand vein or the subcutaneous space. The injection of 5 ml room-temperature (26 °C) saline into the dorsal hand vein enabled the visualization of the vein. When 3 ml of room-temperature saline was injected through the vein into the subcutaneous space, extravasation was detected without any visualization of the vein. The subtraction image before and after the injection clearly showed the temperature changes induced by the saline. Thermography may thus be useful as a monitoring system to detect extravasation of the injected materials.

Mapping Vineyard Leaf Area Using Mobile Terrestrial Laser Scanners: Should Rows be Scanned On-the-Go or Discontinuously Sampled?

Directory of Open Access Journals (Sweden)

Ignacio del-Moral-Martínez

2016-01-01

Full Text Available The leaf area index (LAI is defined as the one-side leaf area per unit ground area, and is probably the most widely used index to characterize grapevine vigor. However, LAI varies spatially within vineyard plots. Mapping and quantifying this variability is very important for improving management decisions and agricultural practices. In this study, a mobile terrestrial laser scanner (MTLS was used to map the LAI of a vineyard, and then to examine how different scanning methods (on-the-go or discontinuous systematic sampling may affect the reliability of the resulting raster maps. The use of the MTLS allows calculating the enveloping vegetative area of the canopy, which is the sum of the leaf wall areas for both sides of the row (excluding gaps and the projected upper area. Obtaining the enveloping areas requires scanning from both sides one meter length section along the row at each systematic sampling point. By converting the enveloping areas into LAI values, a raster map of the latter can be obtained by spatial interpolation (kriging. However, the user can opt for scanning on-the-go in a continuous way and compute 1-m LAI values along the rows, or instead, perform the scanning at discontinuous systematic sampling within the plot. An analysis of correlation between maps indicated that MTLS can be used discontinuously in specific sampling sections separated by up to 15 m along the rows. This capability significantly reduces the amount of data to be acquired at field level, the data storage capacity and the processing power of computers.

THE USE OF MOBILE LASER SCANNING DATA AND UNMANNED AERIAL VEHICLE IMAGES FOR 3D MODEL RECONSTRUCTION

Directory of Open Access Journals (Sweden)

L. Zhu

2013-08-01

Full Text Available The increasing availability in multiple data sources acquired by different sensor platforms has provided the great advantages for desired result achievement. This paper proposes the use of both mobile laser scanning (MLS data and Unmanned Aerial Vehicle (UAV images for 3D model reconstruction. Due to no available exterior orientation parameters for UAV images, the first task is to georeference these images to 3D points. In order to fast and accurate acquire 3D points which are also easy to be found the corresponding locations on UAV images, automated pole extraction from MLS was developed. After georeferencing UAV images, building roofs are acquired from those images and building walls are extracted from MLS data. The roofs and the walls are combined to achieve the complete building models.

The Application of Principal Component Analysis Using Fixed Eigenvectors to the Infrared Thermographic Inspection of the Space Shuttle Thermal Protection System

Science.gov (United States)

Cramer, K. Elliott; Winfree, William P.

2006-01-01

The Nondestructive Evaluation Sciences Branch at NASA s Langley Research Center has been actively involved in the development of thermographic inspection techniques for more than 15 years. Since the Space Shuttle Columbia accident, NASA has focused on the improvement of advanced NDE techniques for the Reinforced Carbon-Carbon (RCC) panels that comprise the orbiter s wing leading edge. Various nondestructive inspection techniques have been used in the examination of the RCC, but thermography has emerged as an effective inspection alternative to more traditional methods. Thermography is a non-contact inspection method as compared to ultrasonic techniques which typically require the use of a coupling medium between the transducer and material. Like radiographic techniques, thermography can be used to inspect large areas, but has the advantage of minimal safety concerns and the ability for single-sided measurements. Principal Component Analysis (PCA) has been shown effective for reducing thermographic NDE data. A typical implementation of PCA is when the eigenvectors are generated from the data set being analyzed. Although it is a powerful tool for enhancing the visibility of defects in thermal data, PCA can be computationally intense and time consuming when applied to the large data sets typical in thermography. Additionally, PCA can experience problems when very large defects are present (defects that dominate the field-of-view), since the calculation of the eigenvectors is now governed by the presence of the defect, not the good material. To increase the processing speed and to minimize the negative effects of large defects, an alternative method of PCA is being pursued when a fixed set of eigenvectors is used to process the thermal data from the RCC materials. These eigen vectors can be generated either from an analytic model of the thermal response of the material under examination, or from a large cross section of experimental data. This paper will provide the

Avaluation of the adaptability of dairy goats with help of thermographic precision in the semiarid brazilian

Directory of Open Access Journals (Sweden)

Elisângela Maria Nunes da Silva

2014-06-01

Full Text Available ABSTRACT. Silva E.M.N., Souza B.B., Silva G.A., Alcântara M.D.B., Cunha M.G.G. & Marques B.A.A. [Avaluation of the adaptability of dairy goats with help of thermographic precision in the semiarid brazilian.] Avaliação da adaptabilidade de caprinos leiteiros com auxílio da precisão termográfica no semiárido brasileiro. Revista Brasileira de Medicina Veterinaria, 36(2:231-237, 2014. Programa de Pós-Graduação em Medicina Veterinária, Universidade Federal de Campina Grande, Rodovia Patos-Teixeira, Km 01, Jatobá, Patos, PB 58708-110, Brasil. E-mail: elisangelamns@yahoo.com.br The present study aimed to evaluate the adaptability of dairy goats with help of thermographic precision in the semiarid brazilian. Thirty-six female goats were used in the study, mean age 2.5 years old and mean weight of 45 kg, all of them pure-bred, lactating and not pregnant, distributed in a completely randomized design, in a factorial outline 2 x 2; two genotypes (Anglo Nubian and Alpine vs two shifts (morning and afternoon with 18 repetitions. Analysis of variance showed that the shift had significant effect (P0.05. Also, there was no significant interaction between breed and shift. Regarding the parameters: respiratory rate (RR and surface temperature of the muzzle of cinnamon there was significant effect of breed and shift and significant interaction between breed and shift (P<0.05. Positive correlations between physiological parameters and room temperature and negative correlation between thermal gradients and more parameters. The Anglo Nubian breed had become more adapted to the semi-arid environmental conditions representing a good alternative for breeding programs. The Alpine breed increased respiratory effort required to dissipate heat and maintain homeothermy, proving to be more demanding regarding system creation and management in the semi-arid climatic conditions.

Scanning or treating device for smooth curved surface

International Nuclear Information System (INIS)

Gemma, A.

1988-01-01

This robot for scanning or treating a smooth curved surface is made by a vehicle moving predeterminately on the surface, this vehicle having mobil grips. A support arm is attached to the vehicle by a swivel and fixed at the center of the curvature. It is orientable parralel to the axes of legs of the vehicle near the center. Scanning or treatment systems for the surface are fixed on the vehicle. Drives and control systems for the vehicle and treatment or scanning system are provided [fr

Modeling neck mobility in fossil turtles

OpenAIRE

Werneburg, Ingmar; Hinz, Juliane K.; Gumpenberger, Michaela; Volpato, Virginie; Natchev, Nikolay; Joyce, Walter G.

2014-01-01

Turtles have the unparalleled ability to retract their heads and necks within their shell but little is known about the evolution of this trait. Extensive analysis of neck mobility in turtles using radiographs, CT scans, and morphometry reveals that basal turtles possessed less mobility in the neck relative to their extant relatives, although the anatomical prerequisites for modern mobility were already established. Many extant turtles are able to achieve hypermobility by dislocating the cent...

Uncertainty propagation using the Monte Carlo method in the measurement of airborne particle size distribution with a scanning mobility particle sizer

Science.gov (United States)

Coquelin, L.; Le Brusquet, L.; Fischer, N.; Gensdarmes, F.; Motzkus, C.; Mace, T.; Fleury, G.

2018-05-01

A scanning mobility particle sizer (SMPS) is a high resolution nanoparticle sizing system that is widely used as the standard method to measure airborne particle size distributions (PSD) in the size range 1 nm–1 μm. This paper addresses the problem to assess the uncertainty associated with PSD when a differential mobility analyzer (DMA) operates under scanning mode. The sources of uncertainty are described and then modeled either through experiments or knowledge extracted from the literature. Special care is brought to model the physics and to account for competing theories. Indeed, it appears that the modeling errors resulting from approximations of the physics can largely affect the final estimate of this indirect measurement, especially for quantities that are not measured during day-to-day experiments. The Monte Carlo method is used to compute the uncertainty associated with PSD. The method is tested against real data sets that are monosize polystyrene latex spheres (PSL) with nominal diameters of 100 nm, 200 nm and 450 nm. The median diameters and associated standard uncertainty of the aerosol particles are estimated as 101.22 nm  ±  0.18 nm, 204.39 nm  ±  1.71 nm and 443.87 nm  ±  1.52 nm with the new approach. Other statistical parameters, such as the mean diameter, the mode and the geometric mean and associated standard uncertainty, are also computed. These results are then compared with the results obtained by SMPS embedded software.

Automatic registration of panoramic image sequence and mobile laser scanning data using semantic features

Science.gov (United States)

Li, Jianping; Yang, Bisheng; Chen, Chi; Huang, Ronggang; Dong, Zhen; Xiao, Wen

2018-02-01

Inaccurate exterior orientation parameters (EoPs) between sensors obtained by pre-calibration leads to failure of registration between panoramic image sequence and mobile laser scanning data. To address this challenge, this paper proposes an automatic registration method based on semantic features extracted from panoramic images and point clouds. Firstly, accurate rotation parameters between the panoramic camera and the laser scanner are estimated using GPS and IMU aided structure from motion (SfM). The initial EoPs of panoramic images are obtained at the same time. Secondly, vehicles in panoramic images are extracted by the Faster-RCNN as candidate primitives to be matched with potential corresponding primitives in point clouds according to the initial EoPs. Finally, translation between the panoramic camera and the laser scanner is refined by maximizing the overlapping area of corresponding primitive pairs based on the Particle Swarm Optimization (PSO), resulting in a finer registration between panoramic image sequences and point clouds. Two challenging urban scenes were experimented to assess the proposed method, and the final registration errors of these two scenes were both less than three pixels, which demonstrates a high level of automation, robustness and accuracy.

Thermographic inspection of bond defects in Fiber Reinforced Polymer applied to masonry structures

Science.gov (United States)

Masini, N.; Aiello, M. A.; Capozzoli, L.; Vasanelli, E.

2012-04-01

Nowadays, externally bonded Fiber Reinforced Polymers (FRP) are extensively used for strengthening and repairing masonry and reinforced concrete existing structures; they have had a rapid spread in the area of rehabilitation for their many advantages over other conventional repair systems, such as lightweight, excellent corrosion and fatigue resistance, high strength, etc. FRP systems applied to masonry or concrete structures are typically installed using a wet-layup technique.The method is susceptible to cause flaws or defects in the bond between the FRP system and the substrate, which may reduce the effectiveness of the reinforcing systems and the correct transfer of load from the structure to the composite. Thus it is of primary importance to detect the presence of defects and to quantify their extension in order to eventually provide correct repair measurements. The IR thermography has been cited by the several guidelines as a good mean to qualitatively evaluate the presence of installation defects and to monitor the reinforcing system with time.The method is non-destructive and does not require contact with the composite or other means except air to detect the reinforcement. Some works in the literature have been published on this topic. Most of the researches aim at using the IR thermography technique to characterize quantitatively the defects in terms of depth, extension and type in order to have an experimental database on defect typology to evaluate the long term performances of the reinforcing system. Nevertheless, most of the works in the literature concerns with FRP applied to concrete structures without considering the case of masonry structures. In the present research artificial bond defects between FRP and the masonry substrate have been reproduced in laboratory and the IR multi temporal thermography technique has been used to detect them. Thermographic analysis has been carried out on two wall samples having limited dimensions (100 x 70 cm) both

Relationship Between the Elevated Muscle FDG Uptake in the Distal Upper Extremities on PET/CT Scan and Prescan Utilization of Mobile Devices in Young Patients.

Science.gov (United States)

Bai, Xia; Wang, Xuemei; Zhuang, Hongming

2018-03-01

It is common to notice increased FDG activity in the muscles of the forearms or hands on PET/CT images. The purpose of this study was to determine relationship between the prevalence of increased FDG activity in the forearms or hands and using mobile devices prior to the FDG PET/CT study. A total of 443 young patients with ages between 5 and 19 years who underwent FDG PET/CT scan were included in this retrospective analysis. All patients had FDG PET/CT with their arms within the field of views. The images were reviewed for elevated activity in the muscles of the distal upper extremities (DUEs), which include forearms and hands. The preimaging questionnaire/interview records regarding using mobile devices prior to FDG PET/CT were also reviewed and compared with the imaging findings. Most patients (72.0% [319/443]) used mobile devices more than 60 minutes in the period of 24 hours prior to the FDG PET/CT study. Elevated uptake in the muscles in the DUEs was observed in 38.6% (123/319) of these patients. In contrast, among 124 patients who did not use the mobile devices or used the mobile device minimally prior to the study, only 6.5% (8/124) of them had elevated FDG activity in the DUEs. The difference persisted following stratification analysis for sex, age, and serum glucose level in our patient population. Increased FDG uptake in the muscles of the DUEs in young patients is commonly seen in those who used mobile devices prior to PET/CT study. Recommendation should be considered to reduce using mobile devices prior to FDG PET/CT study in young patient population.

VirtoScan - a mobile, low-cost photogrammetry setup for fast post-mortem 3D full-body documentations in x-ray computed tomography and autopsy suites.

Science.gov (United States)

Kottner, Sören; Ebert, Lars C; Ampanozi, Garyfalia; Braun, Marcel; Thali, Michael J; Gascho, Dominic

2017-03-01

Injuries such as bite marks or boot prints can leave distinct patterns on the body's surface and can be used for 3D reconstructions. Although various systems for 3D surface imaging have been introduced in the forensic field, most techniques are both cost-intensive and time-consuming. In this article, we present the VirtoScan, a mobile, multi-camera rig based on close-range photogrammetry. The system can be integrated into automated PMCT scanning procedures or used manually together with lifting carts, autopsy tables and examination couch. The VirtoScan is based on a moveable frame that carries 7 digital single-lens reflex cameras. A remote control is attached to each camera and allows the simultaneous triggering of the shutter release of all cameras. Data acquisition in combination with the PMCT scanning procedures took 3:34 min for the 3D surface documentation of one side of the body compared to 20:20 min of acquisition time when using our in-house standard. A surface model comparison between the high resolution output from our in-house standard and a high resolution model from the multi-camera rig showed a mean surface deviation of 0.36 mm for the whole body scan and 0.13 mm for a second comparison of a detailed section of the scan. The use of the multi-camera rig reduces the acquisition time for whole-body surface documentations in medico-legal examinations and provides a low-cost 3D surface scanning alternative for forensic investigations.

Design of inspection equipment vehicle of mobile cobalt-60 container scanner

International Nuclear Information System (INIS)

Zhang Yanmin; An Jigang; Zhou Liye; Liu Yisi; Wu Zhifang; Xiang Xincheng; Huang Songling

2000-01-01

The author introduced the design principle of Inspection Equipment Vehicle of TCM-SCAN Mobile 60 Co container inspection system. Three schemes had been compared. The scheme of scan gate in form of pucker-able rails standing on the vehicle was determined. Prototype was prepared in September 1999. Mobile 60 Co container inspection system had the same inspection performance of fixed 60 Co container inspection system

First PET scans in Estonia

International Nuclear Information System (INIS)

Nazarenko, Sergei

2003-01-01

First PET scans in Estonia were performed on 25th November 2002 in North Estonia Regional Hospital, Tallinn. Six patients with melanoma underwent scanning with FDG. This event was a result of thorough extensive preparations first started in 2000 during the European Association of Nuclear Medicine congress in Paris. During the congress first contacts were made with providers of mobile PET units. At the same time negotiations were begun with potential FDG suppliers. For the introduction of PET in Estonia mobile truckmounted scanning technology was chosen due to low level of initial investments. Of particular importance was also availability of maintenance personnel from the device providers. A significant prerequisite was potential availability of FDG from the neighbourhood - Finland and Sweden. The latter avoided the necessity for investments into local cyclotrons and local FDG production. For the first scanning experience the dedicated truckmounted PET-camera Accel, Siemens was brought by the International Hospital Group (IHG, Amersfoort, Netherlands). The device arrived by ferry from Stockholm to Tallinn harbour at 10 o'clock in the morning and left by ferry for Helsinki at 23 o'clock. The team-on-truck consisted of one technician for device operation, two drivers and two company representatives. North Estonia Regional Hospital provided three additional technicians for patient preparation and FDG injection, one nuclear medicine doctor and one specialist of biomedical engineering and medical physics. The FDG was provided by MAP Medical Technologies, Schering, Helsinki, Finland. The shipments were made by air. This was possible due to small distance between Tallinn and Helsinki of approximately 80 km due to the regular flight connections between the two cities. The FDG was shipped in two lots with a time interval of 4 hours. The patient selection was based on clinical and histopathology data. In all six patients the exam was justified for detailied staging and

Mobile Laser Scanning along Dieppe coastal cliffs: reliability of the acquired point clouds applied to rockfall assessments

Science.gov (United States)

Michoud, Clément; Carrea, Dario; Augereau, Emmanuel; Cancouët, Romain; Costa, Stéphane; Davidson, Robert; Delacourt, Chirstophe; Derron, Marc-Henri; Jaboyedoff, Michel; Letortu, Pauline; Maquaire, Olivier

2013-04-01

Dieppe coastal cliffs, in Normandy, France, are mainly formed by sub-horizontal deposits of chalk and flintstone. Largely destabilized by an intense weathering and the Channel sea erosion, small and large rockfalls are regularly observed and contribute to retrogressive cliff processes. During autumn 2012, cliff and intertidal topographies have been acquired with a Terrestrial Laser Scanner (TLS) and a Mobile Laser Scanner (MLS), coupled with seafloor bathymetries realized with a multibeam echosounder (MBES). MLS is a recent development of laser scanning based on the same theoretical principles of aerial LiDAR, but using smaller, cheaper and portable devices. The MLS system, which is composed by an accurate dynamic positioning and orientation (INS) devices and a long range LiDAR, is mounted on a marine vessel; it is then possible to quickly acquire in motion georeferenced LiDAR point clouds with a resolution of about 15 cm. For example, it takes about 1 h to scan of shoreline of 2 km long. MLS is becoming a promising technique supporting erosion and rockfall assessments along the shores of lakes, fjords or seas. In this study, the MLS system used to acquire cliffs and intertidal areas of the Cap d'Ailly was composed by the INS Applanix POS-MV 320 V4 and the LiDAR Optech Ilirs LR. On the same day, three MLS scans with large overlaps (J1, J21 and J3) have been performed at ranges from 600 m at 4 knots (low tide) up to 200 m at 2.2 knots (up tide) with a calm sea at 2.5 Beaufort (small wavelets). Mean scan resolutions go from 26 cm for far scan (J1) to about 8.1 cm for close scan (J3). Moreover, one TLS point cloud on this test site has been acquired with a mean resolution of about 2.3 cm, using a Riegl LMS Z390i. In order to quantify the reliability of the methodology, comparisons between scans have been realized with the software Polyworks™, calculating shortest distances between points of one cloud and the interpolated surface of the reference point cloud. A Mat

Structure, Mobility, and Composition of Transition Metal Catalyst Surfaces. High-Pressure Scanning Tunneling Microscopy and Ambient-Pressure X-ray Photoelectron Spectroscopy Studies

Energy Technology Data Exchange (ETDEWEB)

Zhu, Zhongwei [Univ. of California, Berkeley, CA (United States)

2013-12-06

Surface structure, mobility, and composition of transition metal catalysts were studied by high-pressure scanning tunneling microscopy (HP-STM) and ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) at high gas pressures. HP-STM makes it possible to determine the atomic or molecular rearrangement at catalyst surfaces, particularly at the low-coordinated active surface sites. AP-XPS monitors changes in elemental composition and chemical states of catalysts in response to variations in gas environments. Stepped Pt and Cu single crystals, the hexagonally reconstructed Pt(100) single crystal, and Pt-based bimetallic nanoparticles with controlled size, shape and composition, were employed as the model catalysts for experiments in this thesis.

Laser Doppler imaging, thermographic imaging, and tissue oxygen saturation measurements detect early skin reactions during breast radiotherapy

Science.gov (United States)

Harrison, David K.; Harrison, Eileen M.; Newton, David J.; Windsor, Phyllis M.

2001-05-01

A range of acute skin reactions, ranging from mild erythema to moist desquamation, can be seen in patients receiving standard fractionated radiotherapy to the breast for conservation therapy of breast carcinoma. In a number of cases these reactions can cause considerable discomfort and seriously affect the patient's quality of life. In previous studies we have used the techniques of laser Doppler imaging, digital thermographic imaging and lightguide spectrophotometry to study oxygen supply and blood flow in inflammatory reactions induced experimentally in forearm skin. The present study is an attempt to use the same techniques to investigate whether any or all of them can detect changes in breast skin very early on in the course of radiotherapy treatment. A further aim of the longer term study is to investigate to what extent these early changes may be able to predict the occurrence later of severe acute or delayed reactions.

3D change detection at street level using mobile laser scanning point clouds and terrestrial images

Science.gov (United States)

Qin, Rongjun; Gruen, Armin

2014-04-01

Automatic change detection and geo-database updating in the urban environment are difficult tasks. There has been much research on detecting changes with satellite and aerial images, but studies have rarely been performed at the street level, which is complex in its 3D geometry. Contemporary geo-databases include 3D street-level objects, which demand frequent data updating. Terrestrial images provides rich texture information for change detection, but the change detection with terrestrial images from different epochs sometimes faces problems with illumination changes, perspective distortions and unreliable 3D geometry caused by the lack of performance of automatic image matchers, while mobile laser scanning (MLS) data acquired from different epochs provides accurate 3D geometry for change detection, but is very expensive for periodical acquisition. This paper proposes a new method for change detection at street level by using combination of MLS point clouds and terrestrial images: the accurate but expensive MLS data acquired from an early epoch serves as the reference, and terrestrial images or photogrammetric images captured from an image-based mobile mapping system (MMS) at a later epoch are used to detect the geometrical changes between different epochs. The method will automatically mark the possible changes in each view, which provides a cost-efficient method for frequent data updating. The methodology is divided into several steps. In the first step, the point clouds are recorded by the MLS system and processed, with data cleaned and classified by semi-automatic means. In the second step, terrestrial images or mobile mapping images at a later epoch are taken and registered to the point cloud, and then point clouds are projected on each image by a weighted window based z-buffering method for view dependent 2D triangulation. In the next step, stereo pairs of the terrestrial images are rectified and re-projected between each other to check the geometrical

Establishing Differences in Thermographic Patterns between the Various Complications in Diabetic Foot Disease

Directory of Open Access Journals (Sweden)

Alfred Gatt

2018-01-01

Full Text Available Aim. To evaluate the potential of thermography as an assessment tool for the detection of foot complications by understanding the variations in temperature that occur in type 2 diabetes mellitus (DM. Methods. Participants were categorized according to a medical examination, ankle brachial index, doppler waveform analysis, and 10-gram monofilament testing into five groups: healthy adult, DM with no complications, DM with peripheral neuropathy, DM with neuroischaemia, and DM with peripheral arterial disease (PAD groups. Thermographic imaging of the toes and forefeet was performed. Results. 43 neuroischaemic feet, 41 neuropathic feet, 58 PAD feet, 21 DM feet without complications, and 126 healthy feet were analyzed. The temperatures of the feet and toes were significantly higher in the complications group when compared to the healthy adult and DM healthy groups. The higher the temperatures of the foot in DM, the higher the probability that it is affected by neuropathy, neuroischaemia, or PAD. Conclusions. Significant differences in mean temperatures exist between participants who were healthy and those with DM with no known complications when compared to participants with neuroischaemia, neuropathy, or PAD. As foot temperature rises, so does the probability of the presence of complications of neuropathy, neuroischaemia, or peripheral arterial disease.

Heat Tolerance in Curraleiro Pe-Duro, Pantaneiro and Nelore Cattle Using Thermographic Images

Directory of Open Access Journals (Sweden)

Caio Cesar Cardoso

2016-01-01

Full Text Available The objective of this study was to compare physiological and thermographic responses to heat stress in three breeds of cattle. Fifteen animals of each of the Nelore, Pantaneiro and Curraleiro Pe-Duro breeds, of approximately two years of age, were evaluated. Heart and respiratory rates, rectal and surface temperature of animals as well as soil temperature were recorded at 8:30 and 15:30 on six days. Variance, correlation, principal factors and canonical analyses were carried out. There were significant differences in the rectal temperature, heart and respiratory rate between breeds (p < 0.001. Nelore and Pantaneiro breeds had the highest rectal temperatures and the lowest respiratory rate (p < 0.001. Breed was also significant for surface temperatures (p < 0.05 showing that this factor significantly affected the response of the animal to heat tolerance in different ways. The Curraleiro Pe-Duro breed had the lowest surface temperatures independent of the period evaluated, with fewer animals that suffered with the climatic conditions, so this may be considered the best adapted when heat challenged under the experimental conditions. Thermography data showed a good correlation with the physiological indexes, and body area, neck and rump were the main points.

System for leaks inspection in a nuclear plant by means of a mobile robot; Sistema para inspeccion de fugas en una planta nuclear por medio de un robot movil

Energy Technology Data Exchange (ETDEWEB)

Ramirez S, R.; Segovia de los Rios, J.A. [ININ, Km. 36.5 Carretera Mexico-Toluca, Salazar, Edo. de Mexico (Mexico)]. E-mail: ramses@nuclear.inin.mx

2004-07-01

In this work a supervision system that could allow to carry out the detection of leaks of vapor in pipe lines, using a mobile robot Pioneer 2 -D Xe, which is controlled by means of an external micro controller 68HC912B32 programmed in Forth and using diffuse control to travel a road by means of the one to follow one lines painted in the floor is described. The robot takes in his superior part, a thermographic camera that allows to determine if leaks of vapor exist in pipes and a dosemeter to measure the present radiation levels in the place, besides a video camera. This way, the personnel, can make sure of having a propitious situation to make the maintenance of the facilities. (Author)

Radial microstrip slotline feed network for circular mobile communications array

Science.gov (United States)

Simons, Rainee N.; Kelly, Eron S.; Lee, Richard Q.; Taub, Susan R.

1994-01-01

In mobile and satellite communications there is a need for low cost and low profile antennas which have a toroidal pattern. Antennas that have been developed for mobile communications include a L-Band electronically steered stripline phased array, a Ka-Band mechanically steered elliptical reflector antenna and a Ka-Band printed dipole. In addition, a L-Band mechanically steered microstrip array, a L-Band microstrip phased array tracking antenna for mounting on a car roof and an X-Band radial line slotted waveguide antenna have been demonstrated. In the above electronically scanned printed arrays, the individual element radiates normally to the plane of the array and hence require a phase shifter to scan the beam towards the horizon. Scanning in the azimuth is by mechanical or electronic steering. An alternate approach is to mount microstrip patch radiators on the surface of a cone to achieve the required elevation angle. The array then scans in the azimuth by beam switching.

A CdZnTe slot-scanned detector for digital mammography

International Nuclear Information System (INIS)

Mainprize, James G.; Ford, Nancy L.; Yin Shi; Gordon, Eli E.; Hamilton, William J.; Tuemer, Tuemay O.; Yaffe, Martin J.

2002-01-01

A new high-resolution detector has been developed for use in a slot-scanned digital mammography system. The detector is a hybrid device that consists of a CCD operating in time-delay integration mode that is bonded to a 150-μm-thick CdZnTe photoconductor array. The CCD was designed with a detector element pitch of 50 μm. Two devices were evaluated with differing crystalline quality. Incomplete charge collection was a source of reduction in DQE. This occurs in both devices due to characteristically low mobility-lifetime products for CdZnTe, with the greatest losses demonstrated by the multicrystalline sample. The mobility-lifetime products for the multicrystalline device were found to be 2.4x10 -4 and 4.0x10 -7 cm 2 /V for electrons and holes, respectively. The device constructed with higher quality single crystal CdZnTe demonstrated mobility-lifetime products of 1.0x10 -4 and 4.4x10 -6 cm 2 /V for electrons and holes. The MTF and DQE for the device were measured at several exposures and results were compared to predictions from a linear systems model of signal and noise propagation. The MTF at a spatial frequency of 10 mm -1 exceeded 0.18 and 0.56 along the scan and slot directions, respectively. Scanning motion and CCD design limited the resolution along the scan direction. For an x-ray beam from a tungsten target tube with 40 μm molybdenum filtration operated at 26 kV, the single crystal device demonstrated a DQE(0) of 0.70±0.02 at 7.1x10 -6 C/kg (27 mR) exposure to the detector, despite its relatively poor charge collection efficiency

Retrieval Algorithms for Road Surface Modelling Using Laser-Based Mobile Mapping

Directory of Open Access Journals (Sweden)

Antero Kukko

2008-09-01

Full Text Available Automated processing of the data provided by a laser-based mobile mapping system will be a necessity due to the huge amount of data produced. In the future, vehiclebased laser scanning, here called mobile mapping, should see considerable use for road environment modelling. Since the geometry of the scanning and point density is different from airborne laser scanning, new algorithms are needed for information extraction. In this paper, we propose automatic methods for classifying the road marking and kerbstone points and modelling the road surface as a triangulated irregular network. On the basis of experimental tests, the mean classification accuracies obtained using automatic method for lines, zebra crossings and kerbstones were 80.6%, 92.3% and 79.7%, respectively.

Harmonisation of nanoparticle concentration measurements using GRIMM and TSI scanning mobility particle sizers

International Nuclear Information System (INIS)

Joshi, Manish; Sapra, B. K.; Khan, Arshad; Tripathi, S. N.; Shamjad, P. M.; Gupta, Tarun; Mayya, Y. S.

2012-01-01

Regional studies focusing on the role of atmospheric nanoparticles in climate change have gained impetus in the last decade. Several multi-institutional studies involving measurement of nanoparticles with several kinds of instruments are on the rise. It is important to harmonize these measurements as the instruments may work on different techniques or principles and are developed by different manufacturers. Scanning mobility particle sizers (SMPS) are often used to measure size distribution of nanoparticles in the airborne phase. Two such commercially available instruments namely, GRIMM and TSI-SMPS have been compared for ambient and laboratory generated conditions. A stand-alone condensation particle counter (CPC) of TSI make was used as a reference for particle concentration measurements. The consistency of the results in terms of mean size and geometric standard deviation was seen to be excellent for both the SMPSs, with GRIMM always showing slightly (approximately 10 %) lower mean size. The integrated number concentration from GRIMM-SMPS was seen to be closer to stand-alone reference CPC compared to TSI-SMPS, for an ambient overnight comparison. However, a concentration-dependent response, i.e. the variations between the two instruments increasing with the concentration, was observed and possible reasons for this have been suggested. A separate experiment was performed for studying the modifying effect of diffusion dryer and sheath air dryer on the measured aerosol size spectra. A significant hygroscopic growth was noted when diffusion dryer was attached to one of the SMPS. The introduction of sheath air dryer in GRIMM-SMPS produced a significant shift towards lower mean size. These results have been compared and discussed with the recent inter-comparison results to strengthen and harmonize the measurement protocols.

Harmonisation of nanoparticle concentration measurements using GRIMM and TSI scanning mobility particle sizers

Science.gov (United States)

Joshi, Manish; Sapra, B. K.; Khan, Arshad; Tripathi, S. N.; Shamjad, P. M.; Gupta, Tarun; Mayya, Y. S.

2012-12-01

Regional studies focusing on the role of atmospheric nanoparticles in climate change have gained impetus in the last decade. Several multi-institutional studies involving measurement of nanoparticles with several kinds of instruments are on the rise. It is important to harmonize these measurements as the instruments may work on different techniques or principles and are developed by different manufacturers. Scanning mobility particle sizers (SMPS) are often used to measure size distribution of nanoparticles in the airborne phase. Two such commercially available instruments namely, GRIMM and TSI-SMPS have been compared for ambient and laboratory generated conditions. A stand-alone condensation particle counter (CPC) of TSI make was used as a reference for particle concentration measurements. The consistency of the results in terms of mean size and geometric standard deviation was seen to be excellent for both the SMPSs, with GRIMM always showing slightly (approximately 10 %) lower mean size. The integrated number concentration from GRIMM-SMPS was seen to be closer to stand-alone reference CPC compared to TSI-SMPS, for an ambient overnight comparison. However, a concentration-dependent response, i.e. the variations between the two instruments increasing with the concentration, was observed and possible reasons for this have been suggested. A separate experiment was performed for studying the modifying effect of diffusion dryer and sheath air dryer on the measured aerosol size spectra. A significant hygroscopic growth was noted when diffusion dryer was attached to one of the SMPS. The introduction of sheath air dryer in GRIMM-SMPS produced a significant shift towards lower mean size. These results have been compared and discussed with the recent inter-comparison results to strengthen and harmonize the measurement protocols.

Evaluation in vitro of effects of Er:YAG and Nd:YAG lasers irradiation on root canal wall, by stereoscopy, scanning electron micrography and thermographic camera; Avaliacao in vitro dos efeitos da irradiacao laser de Er:YAG e Nd:YAG na parede dentinaria do canal radicular, sob observacao do estereoscopio, da micrografia eletronica e da camera termografica

Energy Technology Data Exchange (ETDEWEB)

Goya, Claudia

2001-07-01

This study was carried out to evaluate in vitro the effects of Nd:YAG laser and Er:YAG laser irradiation in the root canal wall by SEM, evaluating the apical leakage and the temperature changes during the laser irradiation. Seventy four extracted human teeth were used, they were instrumented and divided into seven groups of 10 teeth each. The teeth were evaluated through stereoscopy, by SEM, and with the thermographic camera. The Nd:YAG laser irradiation parameters were 100 mJ/p, 15 Hz, and Er:YAG laser were 160 mJ/p and 10 Hz, the irradiation was 4 times at 2 mm/sec speed, with 20 sec interval. The apical leakage was not observed in the teeth irradiated by Nd:YAG laser alone or in association with Er:YAG laser. However in the teeth irradiated only by the Er:YAG laser we observed a little leakage. By SEM observation the Nd:YAG laser irradiation showed melting and recrystallization in the dentin surface closing dentinal tubules, and in the samples irradiated by Er:Y AG laser a clean surface, opened dentinal tubules, and the combination by two lasers, showed melting covering some dentinal tubules The thermographic study found the temperature increase was not more than 6 deg C. This study showed the safety parameters applications of Er:YAG laser in association with Nd:YAG laser in root canal treatment, in order to not cause thermal damages to the periodontal tissues. (author)

A FEASIBILITY STUDY ON USE OF GENERIC MOBILE LASER SCANNING SYSTEM FOR DETECTING ASPHALT PAVEMENT CRACKS

Directory of Open Access Journals (Sweden)

X. Chen

2016-06-01

Full Text Available This study aims to automatically detect pavement cracks on urban roads by employing the 3D point clouds acquired by a mobile laser scanning (MLS system. Our method consists of four steps: ground point filtering, high-pass convolution, matched filtering, and noise removal. First, a voxel-based upward growing method is applied to construct Digital Terrain Model (DTM of the road surface. Then, a high-pass filter convolutes the DTM to detect local elevation changes that may embed cracking information. Next, a two-step matched filter is applied to extract crack features. Lastly, a noise removal process is conducted to refine the results. Instead of using MLS intensity, this study takes advantages of the MLS elevation information to perform automated crack detection from large-volume, mixed-density, unstructured MLS point clouds. Four types of cracks including longitudinal, transvers, random, and alligator cracks are detected. Our results demonstrated that the proposed method works well with the RIEGL VMX-450 point clouds and can detect cracks in moderate-to-severe severity (13 - 25 mm within a 200 m by 30 m urban road segment located in Kingston, Ontario, at one time. Due to the resolution capability, small cracks with slight severity remain unclear in the MLS point cloud.

Field experience with a mobile tomographic nondestructive assay system

International Nuclear Information System (INIS)

Prettyman, T.H.; Betts, S.E.; Taggart, D.P.; Estep, R.J.; Nicholas, N.J.; Lucas, M.C.; Harlan, R.A.

1995-01-01

A mobile tomographic gamma-ray scanner (TGS) developed by Los Alamos National Laboratory was recently demonstrated at the Rocky Flats Environmental Technology Site and is currently in use at Los Alamos waste storage areas. The scanner was developed to assay radionuclides in low-level, transuranic, and mixed waste in containers ranging in size from 2 ft 3 boxes to 83-gallon overpacks. The tomographic imaging capability provides a complete correction for source distribution and matrix attenuation effects, enabling accurate assays of Pu-239 and other gamma-ray emitting isotopes. In addition, the system can reliably detect self-absorbing material such as plutonium metal shot, and can correct for bias caused by self-absorption. The system can be quickly configured to execute far-field scans, segmented gamma-ray scans, and a host of intermediate scanning protocols, enabling higher throughput (up to 20 drums per 8-hour shift). In this paper, we will report on the results of field trials of the mobile system at Rocky Flats and Los Alamos. Assay accuracy is confirmed for cases in which TGS assays can be compared with assays (e.g. with calorimetry) of individual packages within the drums. The mobile tomographic technology is expected to considerably reduce characterization costs at DOE production and environmental technology sites

Thermographic analysis of photodynamic therapy with intense pulsed light and needle-free injection photosensitizer delivery: an animal study

Science.gov (United States)

Requena, Michelle B.; Stringasci, Mirian D.; Pratavieira, Sebastião.; Vollet-Filho, José Dirceu; de Nardi, Andrigo B.; Escobar, Andre; da Rocha, Rozana W.; Bagnato, Vanderlei S.; de Menezes, Priscila F. C.

2018-02-01

The photodynamic therapy (PDT) is a therapeutic modality that depends mostly on photosensitizer (PS), light and molecular oxygen species. However, there are still technical limitations in clinical PDT that are under constant development, particularly concerning PS and light delivery. Intense Pulsed Light (IPL) sources are systems able to generate pulses of high energy with polychromatic light. IPL is a technique mainly used in the cosmetic area to perform various skin treatments for therapeutic and aesthetic applications. The goals of this study were to determine temperature variance during the application of IPL in porcine skin model, and the PDT effects using this light source with PS delivery by a commercial high pressure, needle-free injection system. The PSs tested were Indocyanine Green (ICG) and Photodithazine (PDZ), and the results showed an increase bellow 10 °C in the skin surface using a thermographic camera to measure. In conclusion, our preliminary study demonstrated that IPL associated with needle-free injection PS delivery could be a promising alternative to PDT.

Improving vaccine registries through mobile technologies: a vision for mobile enhanced Immunization information systems.

Science.gov (United States)

Wilson, Kumanan; Atkinson, Katherine M; Deeks, Shelley L; Crowcroft, Natasha S

2016-01-01

Immunization registries or information systems are critical to improving the quality and evaluating the ongoing success of immunization programs. However, the completeness of these systems is challenged by a myriad of factors including the fragmentation of vaccine administration, increasing mobility of individuals, new vaccine development, use of multiple products, and increasingly frequent changes in recommendations. Mobile technologies could offer a solution, which mitigates some of these challenges. Engaging individuals to have more control of their own immunization information using their mobile devices could improve the timeliness and accuracy of data in central immunization information systems. Other opportunities presented by mobile technologies that could be exploited to improve immunization information systems include mobile reporting of adverse events following immunization, the capacity to scan 2D barcodes, and enabling bidirectional communication between individuals and public health officials. Challenges to utilizing mobile solutions include ensuring privacy of data, access, and equity concerns, obtaining consent and ensuring adoption of technology at sufficiently high rates. By empowering individuals with their own health information, mobile technologies can also serve as a mechanism to transfer immunization information as individuals cross local, regional, and national borders. Ultimately, mobile enhanced immunization information systems can help realize the goal of the individual, the healthcare provider, and public health officials always having access to the same immunization information. © The Author 2015. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Mobile autonomous robot for radiological surveys

International Nuclear Information System (INIS)

Dudar, A.M.; Wagner, D.G.; Teese, G.D.

1992-01-01

The robotics development group at the Savannah River Laboratory (SRL) is developing a mobile autonomous robot that performs radiological surveys of potentially contaminated floors. The robot is called SIMON, which stands for Semi-Intelligent Mobile Observing Navigator. Certain areas of SRL are classified as radiologically controlled areas (RCAs). In an RCA, radioactive materials are frequently handled by workers, and thus, the potential for contamination is ever present. Current methods used for floor radiological surveying includes labor-intensive manual scanning or random smearing of certain floor locations. An autonomous robot such as SIMON performs the surveying task in a much more efficient manner and will track down contamination before it is contacted by humans. SIMON scans floors at a speed of 1 in./s and stops and alarms upon encountering contamination. Its environment is well defined, consisting of smooth building floors with wide corridors. The kind of contaminations that SIMON is capable of detecting are alpha and beta-gamma. The contamination levels of interest are low to moderate

Crack detection by mobile photothermal probe

International Nuclear Information System (INIS)

Besnard, R.; Le Blanc, A.; Sellier, J.Y.

1993-01-01

This paper deals with an industrial method for crack detection. The apparatus presented is based on a mobile photothermal probe. It can be used under different modes (sinusoidal, pulsed or scanned excitation). Moreover, the description of the device provided includes theoretical and experimental results. (TEC). 7 refs., 6 figs

Dedicated mobile volumetric cone-beam computed tomography for human brain imaging: A phantom study.

Science.gov (United States)

Ryu, Jong-Hyun; Kim, Tae-Hoon; Jeong, Chang-Won; Jun, Hong-Young; Heo, Dong-Woon; Lee, Jinseok; Kim, Kyong-Woo; Yoon, Kwon-Ha

2015-01-01

Mobile computed tomography (CT) with a cone-beam source is increasingly used in the clinical field. Mobile cone-beam CT (CBCT) has great merits; however, its clinical utility for brain imaging has been limited due to problems including scan time and image quality. The aim of this study was to develop a dedicated mobile volumetric CBCT for obtaining brain images, and to optimize the imaging protocol using a brain phantom. The mobile volumetric CBCT system was evaluated with regards to scan time and image quality, measured as signal-to-noise-ratio (SNR), contrast-to-noise-ratio (CNR), spatial resolution (10% MTF), and effective dose. Brain images were obtained using a CT phantom. The CT scan took 5.14 s at 360 projection views. SNR and CNR were 5.67 and 14.5 at 120 kV/10 mA. SNR and CNR values showed slight improvement as the x-ray voltage and current increased (p < 0.001). Effective dose and 10% MTF were 0.92 mSv and 360 μ m at 120 kV/10 mA. Various intracranial structures were clearly visible in the brain phantom images. Using this CBCT under optimal imaging acquisition conditions, it is possible to obtain human brain images with low radiation dose, reproducible image quality, and fast scan time.

Image processing and pattern recognition with CVIPtools MATLAB toolbox: automatic creation of masks for veterinary thermographic images

Science.gov (United States)

Mishra, Deependra K.; Umbaugh, Scott E.; Lama, Norsang; Dahal, Rohini; Marino, Dominic J.; Sackman, Joseph

2016-09-01

CVIPtools is a software package for the exploration of computer vision and image processing developed in the Computer Vision and Image Processing Laboratory at Southern Illinois University Edwardsville. CVIPtools is available in three variants - a) CVIPtools Graphical User Interface, b) CVIPtools C library and c) CVIPtools MATLAB toolbox, which makes it accessible to a variety of different users. It offers students, faculty, researchers and any user a free and easy way to explore computer vision and image processing techniques. Many functions have been implemented and are updated on a regular basis, the library has reached a level of sophistication that makes it suitable for both educational and research purposes. In this paper, the detail list of the functions available in the CVIPtools MATLAB toolbox are presented and how these functions can be used in image analysis and computer vision applications. The CVIPtools MATLAB toolbox allows the user to gain practical experience to better understand underlying theoretical problems in image processing and pattern recognition. As an example application, the algorithm for the automatic creation of masks for veterinary thermographic images is presented.

Thermographical Measuring of the Skin Temperature Using Laser Needle Acupuncture in Preterm Neonates

Directory of Open Access Journals (Sweden)

Wolfgang Raith

2012-01-01

Full Text Available In children, laser acupuncture is used more often than needle acupuncture in Western countries, due to their aversion to needles. When applying laser acupuncture to premature babies and neonates, firstly the degree of the thermal increase to the skin has to be evaluated so as to guarantee safe application. The patients were premature neonates before their discharge from hospital. The measurements were carried out by means of a polygraphy while they were asleep shortly. The large intestine 4 acupoint (LI4, Hegu was stimulated by a microlaser needle (10 mW, 685 nm twice (5 and 10 min. Local thermographic pictures were taken with a thermal camera (Flir i5, Flir Systems Inc., Portland, USA, and the warmest point was determined and subsequently compared. The study included 10 premature neonates (7 male, 3 female. The measurements were carried out on the 33rd day of life (weight 2030 g, gestational age 36+3 weeks of pregnancy. In comparison to the initial temperature (32.9C°, after 5 minutes of stimulation (33.9°C (P=0.025 and also after 10 minutes of stimulation (34.0°C (P=0.01, there was found to be a significant increase in the skin temperature. The singular maximum value of 37.9°C bears a potential danger; however, compared to the local temperatures reached in transcutaneous blood gas measurements it appears not to entail any risks.

High Pressure Scanning Tunneling Microscopy Studies of Adsorbate Structure and Mobility during Catalytic Reactions. Novel Design of an Ultra High Pressure, High Temperature Scanning Tunneling Microscope System for Probing Catalytic Conversions

International Nuclear Information System (INIS)

Tang, David Chi-Wai

2005-01-01

The aim of the work presented therein is to take advantage of scanning tunneling microscope's (STM) capability for operation under a variety of environments under real time and at atomic resolution to monitor adsorbate structures and mobility under high pressures, as well as to design a new generation of STM systems that allow imaging in situ at both higher pressures (35 atm) and temperatures (350 C). The design of a high pressure, high temperature scanning tunneling microscope system, that is capable of monitoring reactions in situ at conditions from UHV and ambient temperature up to 1 atm and 250 C, is briefly presented along with vibrational and thermal analysis, as this system serves as a template to improve upon during the design of the new ultra high pressure, high temperature STM. Using this existing high pressure scanning tunneling microscope we monitored the co-adsorption of hydrogen, ethylene and carbon dioxide on platinum (111) and rhodium (111) crystal faces in the mTorr pressure range at 300 K in equilibrium with the gas phase. During the catalytic hydrogenation of ethylene to ethane in the absence of CO the metal surfaces are covered by an adsorbate layer that is very mobile on the time scale of STM imaging. We found that the addition of CO poisons the hydrogenation reaction and induces ordered structures on the single crystal surfaces. Several ordered structures were observed upon CO addition to the surfaces pre-covered with hydrogen and ethylene: a rotated (√19 x √19)R23.4 o on Pt(111), and domains of c(4 x 2)-CO+C 2 H 3 , previously unobserved (4 x 2)-CO+3C 2 H 3 , and (2 x 2)-3CO on Rh(111). A mechanism for CO poisoning of ethylene hydrogenation on the metal single crystals was proposed, in which CO blocks surface metal sites and reduces adsorbate mobility to limit adsorption and reaction rate of ethylene and hydrogen. In order to observe heterogeneous catalytic reactions that occur well above ambient pressure and temperature that more closely

Apps and Mobile Support Services in Canadian Academic Medical Libraries

Directory of Open Access Journals (Sweden)

Tess Grynoch

2016-12-01

Full Text Available Objective: To examine how Canadian academic medical libraries are supporting mobile apps, what apps are currently being provided by these libraries, and what types of promotion are being used. Methods: A survey of the library websites for the 17 medical schools in Canada was completed. For each library website surveyed, the medical apps listed on the website, any services mentioned through this medium, and any type of app promotion events were noted. When Facebook and Twitter accounts were evident, the tweets were searched and the past two years of Facebook posts scanned for mention of medical apps or mobile services/events. Results: All seventeen academic medical libraries had lists of mobile medical apps with a large range in the number of medical relevant apps (average=31, median= 23. A total of 275 different apps were noted and the apps covered a wide range of subjects. Five of the 14 Facebook accounts scanned had posts about medical apps in the past two years while 11 of the 15 Twitter accounts had tweets about medical apps. Social media was only one of the many promotional methods noted. Outside of the app lists and mobile resources guides, Canadian academic medical libraries are providing workshops, presentations, and drop-in sessions for mobile medical apps. Conclusion: While librarians cannot simply compare mobile services and resources between academic medical libraries without factoring in a number of other circumstances, librarians can learn from mobile resources strategies employed at other libraries, such as using research guides to increase medical app literacy.

a Man-Portable Imu-Free Mobile Mapping System

Science.gov (United States)

Nüchter, A.; Borrmann, D.; Koch, P.; Kühn, M.; May, S.

2015-08-01

Mobile mapping systems are commonly mounted on cars, ships and robots. The data is directly geo-referenced using GPS data and expensive IMU (inertial measurement systems). Driven by the need for flexible, indoor mapping systems we present an inexpensive mobile mapping solution that can be mounted on a backpack. It combines a horizontally mounted 2D profiler with a constantly spinning 3D laser scanner. The initial system featuring a low-cost MEMS IMU was revealed and demonstrated at MoLaS: Technology Workshop Mobile Laser Scanning at Fraunhofer IPM in Freiburg in November 2014. In this paper, we present an IMU-free solution.

Supportive Noninvasive Tool for the Diagnosis of Breast Cancer Using a Thermographic Camera as Sensor

Directory of Open Access Journals (Sweden)

Marco Antonio Garduño-Ramón

2017-03-01

Full Text Available Breast cancer is the leading disease in incidence and mortality among women in developing countries. The opportune diagnosis of this disease strengthens the survival index. Mammography application is limited by age and periodicity. Temperature is a physical magnitude that can be measured by using multiple sensing techniques. IR (infrared thermography using commercial cameras is gaining relevance in industrial and medical applications because it is a non-invasive and non-intrusive technology. Asymmetrical temperature in certain human body zones is associated with cancer. In this paper, an IR thermographic sensor is applied for breast cancer detection. This work includes an automatic breast segmentation methodology, to spot the hottest regions in thermograms using the morphological watershed operator to help the experts locate the tumor. A protocol for thermogram acquisition considering the required time to achieve a thermal stabilization is also proposed. Breast thermograms are evaluated as thermal matrices, instead of gray scale or false color images, increasing the certainty of the provided diagnosis. The proposed tool was validated using the Database for Mastology Research and tested in a voluntary group of 454 women of different ages and cancer stages with good results, leading to the possibility of being used as a supportive tool to detect breast cancer and angiogenesis cases.

Multi-Range Conditional Random Field for Classifying Railway Electrification System Objects Using Mobile Laser Scanning Data

Directory of Open Access Journals (Sweden)

Jaewook Jung

2016-12-01

Full Text Available Railways have been used as one of the most crucial means of transportation in public mobility and economic development. For safe railway operation, the electrification system in the railway infrastructure, which supplies electric power to trains, is an essential facility for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS data into ten target classes representing overhead wires, movable brackets and poles, which are key objects in the electrification system. In general, the layout of the railway electrification system shows strong spatial regularity relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF, which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds are converted into a set of line segments to which the labeling process is applied. Support Vector Machine (SVM is used as a local classifier considering only node features for producing the unary potentials of the CRF model. As the short-range pairwise contextual term, the Potts model is applied to enforce a local smoothness in the short-range graph; while long-range pairwise potentials are designed to enhance the spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by the naive Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables, which represent the co-occurrence rate of spatial relations in the horizontal and vertical

Extended investigation into continuous laser scanning of underground mine workings by means of Landis inertial navigation system

Science.gov (United States)

Belyaev, E. N.

2017-10-01

The paper investigates the method of applying mobile scanning systems (MSSs) with inertial navigators in the underground conditions for carrying out the surveying tasks. The available mobile laser scanning systems cannot be used in the underground environment since Global Positioning System (GPS) signals cannot be received in mines. This signal not only is necessary for space positioning, but also operates as the main corrective signal for the primary navigation system - the inertial navigation system. The idea of the method described in this paper consists in using MSSs with a different correction of the inertial system than GPS is.

A walk by the river: three-dimensional reconstruction of surface sedimentology and topography using wearable laser scanning

Science.gov (United States)

Williams, R.; Lamy, M. L.; Stott, E.; Maniatis, G.

2017-12-01

In the last two decades, quantification of fluvial topography has been transformed by a number of geomatics technologies that have enabled the acquisition of data with unprecedented spatial resolution. Hyperscale surveys with spatial extents of <1 km2 have been widely demonstrated, by means of Terrestrial Laser Scanning (TLS) and Structure-from-Motion (SfM) photogrammetry. Recent advances in the development and integration of GNSS, IMU, lightweight laser scanning and SLAM technologies are now resulting in the emergence of wearable, mobile laser scanning systems that have the potential to increase data acquisition and processing rates by 1-2 orders of magnitude compared to TLS/SfM, and thus challenge the recent dominance of these two geomatics technologies. In this study we describe the methods and results of a comparison between a wearable laser scanning survey, using a Leica Pegasus Backpack, and a multi-station static TLS survey, using a Riegl VZ-1000 scanner. The evaluation is undertaken on a 600 m long reach of the braided River Feshie, Scotland, using data acquired in June 2017. Comparison between the DEMs produced from static and mobile laser scanning, across non-vegetated areas, revealed a Mean Error (ME) of -0.002 m and a Standard Deviation Error (SDE) of 0.109 m. Comparison to 100 independent check point resulted in a similar ME and SDE for static (ME = 0.061m; SDE = 0.030 m) and mobile (ME = 0.044 m; SDE = 0.029 m) laser scanning. Empirical relationships between sub-metre topographic variability and median sediment grain size (10-100 mm), across 14 grid-by-number samples, were similar and demonstrate that surface roughness from wearable laser scanning can be used to derive reach-scale maps of median grain size. These results demonstrate that wearable laser scanning generates hyperscale topographic models that are comparable in quality to more time-consuming multi-station TLS setups. Wearable laser scanning is likely to be commonly adopted for fluvial

Rapid imaging of mycoplasma in solution using Atmospheric Scanning Electron Microscopy (ASEM)

Energy Technology Data Exchange (ETDEWEB)

Sato, Chikara, E-mail: ti-sato@aist.go.jp [Biomedical Research Institute, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Higashi, Tsukuba, Ibaraki 305-8566 (Japan); Manaka, Sachie [Biomedical Research Institute, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Higashi, Tsukuba, Ibaraki 305-8566 (Japan); Nakane, Daisuke [Department of Biology, Graduate School of Science, Osaka City University, Sumiyoshi-ku, Osaka 558-8585 (Japan); Nishiyama, Hidetoshi; Suga, Mitsuo [Advanced Technology Division, JEOL Ltd., Akishima, Tokyo 196-8558 (Japan); Nishizaka, Takayuki [Department of Physics, Faculty of Science, Gakushuin University, 1-5-1 Mejiro, Toshima-ku, Tokyo 171-8588 (Japan); Miyata, Makoto [Department of Biology, Graduate School of Science, Osaka City University, Sumiyoshi-ku, Osaka 558-8585 (Japan); Maruyama, Yuusuke [Biomedical Research Institute, National Institute of Advanced Industrial Science and Technology (AIST), 1-1-1 Higashi, Tsukuba, Ibaraki 305-8566 (Japan)

2012-01-27

Highlights: Black-Right-Pointing-Pointer Mycoplasma mobile was observed in buffer with the Atmospheric Scanning Electron Microscope. Black-Right-Pointing-Pointer Characteristic protein localizations were visualized using immuno-labeling. Black-Right-Pointing-Pointer M. mobile attached to sialic acid on the SiN film surface within minutes. Black-Right-Pointing-Pointer Cells were observed at low concentrations. Black-Right-Pointing-Pointer ASEM should promote study and early-stage diagnosis of mycoplasma. -- Abstract: Mycoplasma is a genus of bacterial pathogen that causes disease in vertebrates. In humans, the species Mycoplasma pneumoniae causes 15% or more of community-acquired pneumonia. Because this bacterium is tiny, corresponding in size to a large virus, diagnosis using optical microscopy is not easy. In current methods, chest X-rays are usually the first action, followed by serology, PCR amplification, and/or culture, but all of these are particularly difficult at an early stage of the disease. Using Mycoplasma mobile as a model species, we directly observed mycoplasma in buffer with the newly developed Atmospheric Scanning Electron Microscope (ASEM). This microscope features an open sample dish with a pressure-resistant thin film window in its base, through which the SEM beam scans samples in solution, from below. Because of its 2-3 {mu}m-deep scanning capability, it can observe the whole internal structure of mycoplasma cells stained with metal solutions. Characteristic protein localizations were visualized using immuno-labeling. Cells were observed at low concentrations, because suspended cells concentrate in the observable zone by attaching to sialic acid on the silicon nitride (SiN) film surface within minutes. These results suggest the applicability of the ASEM for the study of mycoplasmas as well as for early-stage mycoplasma infection diagnosis.

Aero particles characterization emitted by mobile sources

International Nuclear Information System (INIS)

Rojas V, A.; Romero G, E. T.; Lopez G, H.

2009-01-01

In our country, the mobile sources that conform most of the emissions at the atmosphere, are concentrated on the urban areas. For the present work, samples coming from the escapes of terrestrial transport were obtained, such as: passenger buses, load transport and particular vehicles of the Metropolitan area of the Toluca valley. The material was analyzed by means of scanning electron microscopy of low vacuum and X-ray diffraction. The objective was to characterize the emitted particles by mobile sources, morphological and chemically to know the structure, size and elements that compose them. (Author)

Four-dimensional computed tomographic analysis of esophageal mobility during normal respiration

International Nuclear Information System (INIS)

Dieleman, Edith; Senan, Suresh; Vincent, Andrew; Lagerwaard, Frank J.; Slotman, Ben J.; Soernsen de Koste, John R. van

2007-01-01

Background: Chemo-radiotherapy for thoracic tumors can result in high-grade radiation esophagitis. Treatment planning to reduce esophageal irradiation requires organ motion to be accounted for. In this study, esophageal mobility was assessed using four-dimensional computed tomography (4DCT). Methods and Materials: Thoracic 4DCT scans were acquired on a 16-slice CT scanner in 29 patients. The outer esophageal wall was contoured in two extreme phases of respiration in 9 patients with nonesophageal malignancies. The displacement of the center of contour was measured at 2-cm intervals. In 20 additional patients with Stage I lung cancer, the esophagus was contoured in all 10 phases of each 4DCT at five defined anatomic levels. Both approaches were then applied to 4DCT scans of 4 patients who each had two repeat scans performed. A linear mixed effects model was constructed with fixed effects: measurement direction, measurement type, and measurement location along the cranio-caudal axis. Results: Measurement location and direction were significant descriptive parameters (Wald F-tests, p < 0.001), and the interaction term between the two was significant (p = 0.02). Medio-lateral mobility exceeded dorso-ventral mobility in the lower half of the esophagus but was of a similar magnitude in the upper half. Margins that would have incorporated all movement in medio-lateral and dorso-ventral directions were 5 mm proximally, 7 mm and 6 mm respectively in the mid-esophagus, and 9 mm and 8 mm respectively in the distal esophagus. Conclusions: The distal esophagus shows more mobility. Margins for mobility that can encompass all movement were derived for use in treatment planning, particularly for stereotactic radiotherapy

Pemodelan dan Verifikasi Formal Pengaruh Mobility pattern Terhadap Handoff Latency pada Jaringan WiMAX

Directory of Open Access Journals (Sweden)

I Nym Saputra Wahyu Wijaya

2016-01-01

Full Text Available In order to decrease handoff latency and increase the successful of HHO conventional scheme, a development of handover scheme is done in standard protocol WiMAX IEEE 802.16e by adding mobility pattern. The superiority of handover scheme with mobility pattern can reduce handoff latency up to 50%, mean while the weakness of this scheme is a wrong act in determining target base station are often happen. Simulation can not showing the cause of that error. So, we do formal verification in to hard handover model with mobility pattern.             In this research, behaviour system is modeled with continuous-time Markov chain (CTMC. The model is foccused to aproximating the influence of mobility pattern in to handoff latency from WiMAX hard handover mechanism. In order to set up a series markov chain models handover system can follow steps, such as: represents the state space, give a number in all transitions, generate the rate transition matrix (infinitesimal generator.             Probabilistic model checking in the research are using quantitative properties and qualitative properties. Formal verification concerning properties has relation with handover in WiMAX network showing that 70% from mobile station which doing scanning with mobility pattern are success doing handover. 24% of them doing scanning conventional as a result of wrongness in act determining target base station, so handoff latency which is pictured will bigger than a system that is only use conventional scanning method.

Low-Cost Bluetooth Mobile Positioning for Location-based Application

OpenAIRE

Barahim, Zaafir; Doomun, M. Razvi; Joomun, Nazrana

2012-01-01

Bluetooth is a promising short-range radio network technology. We present a low cost and easily deployed, scalable infrastructure for indoor location-based computing of mobile devices based on Bluetooth technology. The system consists of 2 main components, namely the Bluetooth (BT) Sensor System and the Central Navigation System which have been developed using the JDK 6.0. The Bluetooth Sensor System allows mobile devices whose Bluetooth mode is set to discoverable, to be scanned and detected...

CAMEX-4 MOBILE X-BAND POLARIMETRIC WEATHER RADAR V1

Data.gov (United States)

National Aeronautics and Space Administration — Mobile X-band Polarimetric Weather Radar on Wheels (X-POW)is a Doppler scanning radar operating at 9.3 GHz.with horizontal and vertical polarization. Used for...

Mobile robot motion estimation using Hough transform

Science.gov (United States)

Aldoshkin, D. N.; Yamskikh, T. N.; Tsarev, R. Yu

2018-05-01

This paper proposes an algorithm for estimation of mobile robot motion. The geometry of surrounding space is described with range scans (samples of distance measurements) taken by the mobile robot’s range sensors. A similar sample of space geometry in any arbitrary preceding moment of time or the environment map can be used as a reference. The suggested algorithm is invariant to isotropic scaling of samples or map that allows using samples measured in different units and maps made at different scales. The algorithm is based on Hough transform: it maps from measurement space to a straight-line parameters space. In the straight-line parameters, space the problems of estimating rotation, scaling and translation are solved separately breaking down a problem of estimating mobile robot localization into three smaller independent problems. The specific feature of the algorithm presented is its robustness to noise and outliers inherited from Hough transform. The prototype of the system of mobile robot orientation is described.

Tracking Human Mobility Using WiFi Signals

DEFF Research Database (Denmark)

Sapiezynski, Piotr; Stopczynski, Arkadiusz; Gatej, Radu

2015-01-01

We study six months of human mobility data, including WiFi and GPS traces recorded with high temporal resolution, and find that time series of WiFi scans contain a strong latent location signal. In fact, due to inherent stability and low entropy of human mobility, it is possible to assign location...... to WiFi access points based on a very small number of GPS samples and then use these access points as location beacons. Using just one GPS observation per day per person allows us to estimate the location of, and subsequently use, WiFi access points to account for 80% of mobility across a population....... These results reveal a great opportunity for using ubiquitous WiFi routers for high-resolution outdoor positioning, but also significant privacy implications of such side-channel location tracking....

Modeling neck mobility in fossil turtles.

Science.gov (United States)

Werneburg, Ingmar; Hinz, Juliane K; Gumpenberger, Michaela; Volpato, Virginie; Natchev, Nikolay; Joyce, Walter G

2015-05-01

Turtles have the unparalleled ability to retract their heads and necks within their shell but little is known about the evolution of this trait. Extensive analysis of neck mobility in turtles using radiographs, CT scans, and morphometry reveals that basal turtles possessed less mobility in the neck relative to their extant relatives, although the anatomical prerequisites for modern mobility were already established. Many extant turtles are able to achieve hypermobility by dislocating the central articulations, which raises cautions about reconstructing the mobility of fossil vertebrates. A 3D-model of the Late Triassic turtle Proganochelys quenstedti reveals that this early stem turtle was able to retract its head by tucking it sideways below the shell. The simple ventrolateral bend seen in this stem turtle, however, contrasts with the complex double-bend of extant turtles. The initial evolution of neck retraction therefore occurred in a near-synchrony with the origin of the turtle shell as a place to hide the unprotected neck. In this early, simplified retraction mode, the conical osteoderms on the neck provided further protection. © 2014 Wiley Periodicals, Inc.

Relationship between ocular surface temperature and peripheral vasoconstriction in healthy subjects: a thermographic study.

Science.gov (United States)

Vannetti, Federica; Matteoli, Sara; Finocchio, Lucia; Lacarbonara, Francesco; Sodi, Andrea; Menchini, Ugo; Corvi, Andrea

2014-03-01

An impairment of ocular blood flow regulation is commonly considered one of the main pathogenetic mechanisms involved in the development of several eye diseases, like glaucoma. The aim of this study was to investigate whether an alteration of ocular blood supply induced by peripheral vasoconstriction might be detected by measuring the ocular surface temperature. The ocular surface temperature was evaluated in a group of 38 healthy young subjects (28 males and 10 females; mean age: 25.4 ± 4.1 years) by infrared thermography. For each subject, the experimental procedure consisted of two thermographic acquisitions both lasting 10 s, recorded before and during the immersion of both hands in a mixture of ice and water (1.6 °C ± 0.4 °C). Specifically, the second acquisition began 20 s after the hand immersion. Analysis of variance was used to compare the ocular surface temperature of the two profiles. The analysis of infrared images was carried out every 2 s: at the eye opening (t(0)) until 10 s (t(5)), for both profiles. Data showed that ocular surface temperature increased significantly (p-value temperature at t(0) for P(1) = 0.12 °C ± 0.13 °C). Therefore, these results suggest a response of the ocular hemodynamic to the peripheral vasoconstriction. The ocular surface temperature may represent a cheap, non-invasive and non-time-consuming test to evaluate ocular vaso-regulation.

Determination of smoke plume and layer heights using scanning lidar data

Science.gov (United States)

Vladimir A. Kovalev; Alexander Petkov; Cyle Wold; Shawn Urbanski; Wei Min Hao

2009-01-01

The methodology of using mobile scanning lidar data for investigation of smoke plume rise and high-resolution smoke dispersion is considered. The methodology is based on the lidar-signal transformation proposed recently [Appl. Opt. 48, 2559 (2009)]. In this study, similar methodology is used to create the atmospheric heterogeneity height indicator (HHI...

3002 Humidified Tandem Differential Mobility Analyzer Instrument Handbook

Energy Technology Data Exchange (ETDEWEB)

Uin, Janek [Brookhaven National Lab. (BNL), Upton, NY (United States)

2016-03-01

The Brechtel Manufacturing Inc. (BMI) Humidified Tandem Differential Mobility Analyzer (HT-DMA Model 3002) (Brechtel and Kreidenweis 2000a,b, Henning et al. 2005, Xerxes et al. 2014) measures how aerosol particles of different initial dry sizes grow or shrink when exposed to changing relative humidity (RH) conditions. It uses two different mobility analyzers (DMA) and a humidification system to make the measurements. One DMA selects a narrow size range of dry aerosol particles, which are exposed to varying RH conditions in the humidification system. The second (humidified) DMA scans the particle size distribution output from the humidification system. Scanning a wide range of particle sizes enables the second DMA to measure changes in size or growth factor (growth factor = humidified size/dry size), due to water uptake by the particles. A Condensation Particle Counter (CPC) downstream of the second DMA counts particles as a function of selected size in order to obtain the number size distribution of particles exposed to different RH conditions.

Effects of Intercalation on the Hole Mobility of Amorphous Semiconducting Polymer Blends

KAUST Repository

Cates, Nichole C.

2010-06-08

Fullerenes have been shown to intercalate between the side chains of many crystalline and semicrystalline polymers and to affect the properties of polymer:fullerene bulk heterojunction solar cells. Here we present the first in-depth study of intercalation in an amorphous polymer. We study blends of the widely studied amorphous polymer poly(2-methoxy-5-(3studied amorphous polymer poly(,7·studied amorphous polymer poly(-dimethyloctyloxy)-p-phenylene vinylene) (MDMO-PPV) with a variety of molecules using photoluminescence measurements, scanning electron microscopy, and space-charge limited current mobility measurements. The blends with elevated hole mobilities exhibit complete photoluminescence quenching and show no phase separation in a scanning electron microscope. We conclude that intercalation occurs in MDMO-PPV:fullerene blends and is responsible for the increase in the MDMO-PPV hole mobility by several orders of magnitude when it is blended with fullerenes, despite the dilution of the hole-conducting polymer with an electron acceptor. © 2010 American Chemical Society.

Imaging ballistic carrier trajectories in graphene using scanning gate microscopy

Energy Technology Data Exchange (ETDEWEB)

Morikawa, Sei; Masubuchi, Satoru [Institute of Industrial Science, University of Tokyo, 4-6-1 Komaba, Meguro, Tokyo 153-8505 (Japan); Dou, Ziwei; Wang, Shu-Wei; Smith, Charles G.; Connolly, Malcolm R., E-mail: mrc61@cam.ac.uk [Cavendish Laboratory, Department of Physics, University of Cambridge, Cambridge CB3 0HE (United Kingdom); Watanabe, Kenji; Taniguchi, Takashi [National Institute for Materials Science, 1-1 Namiki, Tsukuba 305-0044 (Japan); Machida, Tomoki, E-mail: tmachida@iis.u-tokyo.ac.jp [Institute of Industrial Science, University of Tokyo, 4-6-1 Komaba, Meguro, Tokyo 153-8505 (Japan); Institute for Nano Quantum Information Electronics, University of Tokyo, 4-6-1 Komaba, Meguro, Tokyo 153-8505 (Japan)

2015-12-14

We use scanning gate microscopy to map out the trajectories of ballistic carriers in high-mobility graphene encapsulated by hexagonal boron nitride and subject to a weak magnetic field. We employ a magnetic focusing geometry to image carriers that emerge ballistically from an injector, follow a cyclotron path due to the Lorentz force from an applied magnetic field, and land on an adjacent collector probe. The local electric field generated by the scanning tip in the vicinity of the carriers deflects their trajectories, modifying the proportion of carriers focused into the collector. By measuring the voltage at the collector while scanning the tip, we are able to obtain images with arcs that are consistent with the expected cyclotron motion. We also demonstrate that the tip can be used to redirect misaligned carriers back to the collector.

Automatic Detection and Classification of Pole-Like Objects for Urban Cartography Using Mobile Laser Scanning Data

Directory of Open Access Journals (Sweden)

Celestino Ordóñez

2017-06-01

Full Text Available Mobile laser scanning (MLS is a modern and powerful technology capable of obtaining massive point clouds of objects in a short period of time. Although this technology is nowadays being widely applied in urban cartography and 3D city modelling, it has some drawbacks that need to be avoided in order to strengthen it. One of the most important shortcomings of MLS data is concerned with the fact that it provides an unstructured dataset whose processing is very time-consuming. Consequently, there is a growing interest in developing algorithms for the automatic extraction of useful information from MLS point clouds. This work is focused on establishing a methodology and developing an algorithm to detect pole-like objects and classify them into several categories using MLS datasets. The developed procedure starts with the discretization of the point cloud by means of a voxelization, in order to simplify and reduce the processing time in the segmentation process. In turn, a heuristic segmentation algorithm was developed to detect pole-like objects in the MLS point cloud. Finally, two supervised classification algorithms, linear discriminant analysis and support vector machines, were used to distinguish between the different types of poles in the point cloud. The predictors are the principal component eigenvalues obtained from the Cartesian coordinates of the laser points, the range of the Z coordinate, and some shape-related indexes. The performance of the method was tested in an urban area with 123 poles of different categories. Very encouraging results were obtained, since the accuracy rate was over 90%.

Time-averaged probability density functions of soot nanoparticles along the centerline of a piloted turbulent diffusion flame using a scanning mobility particle sizer

KAUST Repository

Chowdhury, Snehaunshu

2017-01-23

In this study, we demonstrate the use of a scanning mobility particle sizer (SMPS) as an effective tool to measure the probability density functions (PDFs) of soot nanoparticles in turbulent flames. Time-averaged soot PDFs necessary for validating existing soot models are reported at intervals of ∆x/D∆x/D = 5 along the centerline of turbulent, non-premixed, C2H4/N2 flames. The jet exit Reynolds numbers of the flames investigated were 10,000 and 20,000. A simplified burner geometry based on a published design was chosen to aid modelers. Soot was sampled directly from the flame using a sampling probe with a 0.5-mm diameter orifice and diluted with N2 by a two-stage dilution process. The overall dilution ratio was not evaluated. An SMPS system was used to analyze soot particle concentrations in the diluted samples. Sampling conditions were optimized over a wide range of dilution ratios to eliminate the effect of agglomeration in the sampling probe. Two differential mobility analyzers (DMAs) with different size ranges were used separately in the SMPS measurements to characterize the entire size range of particles. In both flames, the PDFs were found to be mono-modal in nature near the jet exit. Further downstream, the profiles were flatter with a fall-off at larger particle diameters. The geometric mean of the soot size distributions was less than 10 nm for all cases and increased monotonically with axial distance in both flames.

A Switchable 3D-Coverage Phased Array Antenna Package for 5G Mobile Terminals

DEFF Research Database (Denmark)

Ojaroudiparchin, Naser; Shen, Ming; Zhang, Shuai

2016-01-01

This manuscript proposes a new design of a millimeter-wave (mm-Wave) array antenna package with beam steering characteristic for the fifth generation (5G) mobile applications. In order to achieve a broad 3D scanning coverage of the space with high-gain beams, three identical sub arrays of patch a...... and efficiency, which is suitable for 5G mobile communications. In addition, the impact of user’s hand on the antenna performance has been investigated....... antennas have been compactly arranged along the edge region of the mobile phone PCB to form the antenna package. By switching the feeding to one of the sub arrays, the desired direction of coverage can be achieved. The proposed design has >10 dB gain in the upper spherical space, good directivity......This manuscript proposes a new design of a millimeter-wave (mm-Wave) array antenna package with beam steering characteristic for the fifth generation (5G) mobile applications. In order to achieve a broad 3D scanning coverage of the space with high-gain beams, three identical sub arrays of patch...

A Voxel-Based Method for Automated Identification and Morphological Parameters Estimation of Individual Street Trees from Mobile Laser Scanning Data

Directory of Open Access Journals (Sweden)

Hongxing Liu

2013-01-01

Full Text Available As an important component of urban vegetation, street trees play an important role in maintenance of environmental quality, aesthetic beauty of urban landscape, and social service for inhabitants. Acquiring accurate and up-to-date inventory information for street trees is required for urban horticultural planning, and municipal urban forest management. This paper presents a new Voxel-based Marked Neighborhood Searching (VMNS method for efficiently identifying street trees and deriving their morphological parameters from Mobile Laser Scanning (MLS point cloud data. The VMNS method consists of six technical components: voxelization, calculating values of voxels, searching and marking neighborhoods, extracting potential trees, deriving morphological parameters, and eliminating pole-like objects other than trees. The method is validated and evaluated through two case studies. The evaluation results show that the completeness and correctness of our method for street tree detection are over 98%. The derived morphological parameters, including tree height, crown diameter, diameter at breast height (DBH, and crown base height (CBH, are in a good agreement with the field measurements. Our method provides an effective tool for extracting various morphological parameters for individual street trees from MLS point cloud data.

An Online Solution of LiDAR Scan Matching Aided Inertial Navigation System for Indoor Mobile Mapping

OpenAIRE

Niu, Xiaoji; Yu, Tong; Tang, Jian; Chang, Le

2017-01-01

Multisensors (LiDAR/IMU/CAMERA) integrated Simultaneous Location and Mapping (SLAM) technology for navigation and mobile mapping in a GNSS-denied environment, such as indoor areas, dense forests, or urban canyons, becomes a promising solution. An online (real-time) version of such system can extremely extend its applications, especially for indoor mobile mapping. However, the real-time response issue of multisensors is a big challenge for an online SLAM system, due to the different sampling f...

Exploring mobility & workplace choice in a flexible office through post-occupancy evaluation.

Science.gov (United States)

Göçer, Özgür; Göçer, Kenan; Ergöz Karahan, Ebru; İlhan Oygür, Işıl

2018-02-01

Developments in information and communication systems, organisational structure and the nature of work have contributed to the restructuring of work environments. In these new types of work environments, employees do not have assigned workplaces. This arrangement helps organisations to minimise rent costs and increase employee interaction and knowledge exchange through mobility. This post-occupancy evaluation (POE) study focuses on a flexible office in a Gold Leadership in Energy and Environmental Design-certified building in Istanbul. An integrated qualitative and quantitative POE technique with occupancy tracking via barcode scanning and instant surveying has been introduced. Using this unique approach, we examined the directives/drivers in workplace choice and mobility from different perspectives. The aggregated data was used to discern work-related consequences such as flexibility, workplace choice, work and indoor environment satisfaction, place attachment and identity. The results show that employees who have a conventional working culture develop a new working style: 'fixed-flexible working'. Practitioner Summary: This paper introduces a new POE approach for flexible offices based on occupancy tracking through barcode scanning to explore workplace choice and mobility. More than half (52.1%) of the participants have tended to choose the same desk every day. However, the satisfaction level of the 'mobile' employees was higher than that of the 'fixed flexible' employees.

Data processing and quality evaluation of a boat-based mobile laser scanning system.

Science.gov (United States)

Vaaja, Matti; Kukko, Antero; Kaartinen, Harri; Kurkela, Matti; Kasvi, Elina; Flener, Claude; Hyyppä, Hannu; Hyyppä, Juha; Järvelä, Juha; Alho, Petteri

2013-09-17

Mobile mapping systems (MMSs) are used for mapping topographic and urban features which are difficult and time consuming to measure with other instruments. The benefits of MMSs include efficient data collection and versatile usability. This paper investigates the data processing steps and quality of a boat-based mobile mapping system (BoMMS) data for generating terrain and vegetation points in a river environment. Our aim in data processing was to filter noise points, detect shorelines as well as points below water surface and conduct ground point classification. Previous studies of BoMMS have investigated elevation accuracies and usability in detection of fluvial erosion and deposition areas. The new findings concerning BoMMS data are that the improved data processing approach allows for identification of multipath reflections and shoreline delineation. We demonstrate the possibility to measure bathymetry data in shallow (0-1 m) and clear water. Furthermore, we evaluate for the first time the accuracy of the BoMMS ground points classification compared to manually classified data. We also demonstrate the spatial variations of the ground point density and assess elevation and vertical accuracies of the BoMMS data.

Data Processing and Quality Evaluation of a Boat-Based Mobile Laser Scanning System

Directory of Open Access Journals (Sweden)

Petteri Alho

2013-09-01

Full Text Available Mobile mapping systems (MMSs are used for mapping topographic and urban features which are difficult and time consuming to measure with other instruments. The benefits of MMSs include efficient data collection and versatile usability. This paper investigates the data processing steps and quality of a boat-based mobile mapping system (BoMMS data for generating terrain and vegetation points in a river environment. Our aim in data processing was to filter noise points, detect shorelines as well as points below water surface and conduct ground point classification. Previous studies of BoMMS have investigated elevation accuracies and usability in detection of fluvial erosion and deposition areas. The new findings concerning BoMMS data are that the improved data processing approach allows for identification of multipath reflections and shoreline delineation. We demonstrate the possibility to measure bathymetry data in shallow (0–1 m and clear water. Furthermore, we evaluate for the first time the accuracy of the BoMMS ground points classification compared to manually classified data. We also demonstrate the spatial variations of the ground point density and assess elevation and vertical accuracies of the BoMMS data.

Mobile marketing for mobile games

OpenAIRE

Vu, Giang

2016-01-01

Highly developed mobile technology and devices enable the rise of mobile game industry and mobile marketing. Hence mobile marketing for mobile game is an essential key for a mobile game success. Even though there are many articles on marketing for mobile games, there is a need of highly understanding mobile marketing strategies, how to launch a mobile campaign for a mobile game. Besides that, it is essential to understand the relationship between mobile advertising and users behaviours. There...

Simulation and Proposed Handover Alert Algorithm for Mobile Communication System

Directory of Open Access Journals (Sweden)

Muzhir Shaban Al-Ani

2009-10-01

Full Text Available this paper deals with the simulation and presentation of a novel approach to design and implementation of algorithm to realize hand over process for a mobile communication system during mobile network. This algorithm performs the ability of the system to extract important information features about the received signal. When the strength of the received signal is dropped below a certain threshold value then an alert process is activated to achieve the continuity of the transmission due to a ready scan which is existed on time.

Ground-based mobile scanning LIDAR for remote sensing of contrails

Directory of Open Access Journals (Sweden)

F. Homburg

Full Text Available Air traffic is a source of trace gases in the upper troposphere and lower stratosphere. Contrails readily form from water vapor exhausts under favorable meteorological conditions. Since contrails are ice crystal clouds like natural cirrus clouds, they bear a greenhouse potential which has to be investigated. The IFU has built a scanning lidar system employing a pulsed Nd:YAG laser as the emitter and a 52-cm diameter telescope as the receiver. Signals are processed in several channels to investigate depolarization and wavelength dependencies of the light backscattered from ice crystals. These investigations are aimed at the formation and life cycles of contrails, their optical properties, and their climatological consequences in areas of dense air traffic. The experimental lidar setup is described and a sample measurement is shown.

Ground-based mobile scanning LIDAR for remote sensing of contrails

Directory of Open Access Journals (Sweden)

V. Freudenthaler

1994-08-01

Full Text Available Air traffic is a source of trace gases in the upper troposphere and lower stratosphere. Contrails readily form from water vapor exhausts under favorable meteorological conditions. Since contrails are ice crystal clouds like natural cirrus clouds, they bear a greenhouse potential which has to be investigated. The IFU has built a scanning lidar system employing a pulsed Nd:YAG laser as the emitter and a 52-cm diameter telescope as the receiver. Signals are processed in several channels to investigate depolarization and wavelength dependencies of the light backscattered from ice crystals. These investigations are aimed at the formation and life cycles of contrails, their optical properties, and their climatological consequences in areas of dense air traffic. The experimental lidar setup is described and a sample measurement is shown.

3D Participatory Sensing with Low-Cost Mobile Devices for Crop Height Assessment--A Comparison with Terrestrial Laser Scanning Data.

Directory of Open Access Journals (Sweden)

Sabrina Marx

Full Text Available The integration of local agricultural knowledge deepens the understanding of complex phenomena such as the association between climate variability, crop yields and undernutrition. Participatory Sensing (PS is a concept which enables laymen to easily gather geodata with standard low-cost mobile devices, offering new and efficient opportunities for agricultural monitoring. This study presents a methodological approach for crop height assessment based on PS. In-field crop height variations of a maize field in Heidelberg, Germany, are gathered with smartphones and handheld GPS devices by 19 participants. The comparison of crop height values measured by the participants to reference data based on terrestrial laser scanning (TLS results in R2 = 0.63 for the handheld GPS devices and R2 = 0.24 for the smartphone-based approach. RMSE for the comparison between crop height models (CHM derived from PS and TLS data is 10.45 cm (GPS devices and 14.69 cm (smartphones. Furthermore, the results indicate that incorporating participants' cognitive abilities in the data collection process potentially improves the quality data captured with the PS approach. The proposed PS methods serve as a fundament to collect agricultural parameters on field-level by incorporating local people. Combined with other methods such as remote sensing, PS opens new perspectives to support agricultural development.

3D Participatory Sensing with Low-Cost Mobile Devices for Crop Height Assessment--A Comparison with Terrestrial Laser Scanning Data.

Science.gov (United States)

Marx, Sabrina; Hämmerle, Martin; Klonner, Carolin; Höfle, Bernhard

2016-01-01

The integration of local agricultural knowledge deepens the understanding of complex phenomena such as the association between climate variability, crop yields and undernutrition. Participatory Sensing (PS) is a concept which enables laymen to easily gather geodata with standard low-cost mobile devices, offering new and efficient opportunities for agricultural monitoring. This study presents a methodological approach for crop height assessment based on PS. In-field crop height variations of a maize field in Heidelberg, Germany, are gathered with smartphones and handheld GPS devices by 19 participants. The comparison of crop height values measured by the participants to reference data based on terrestrial laser scanning (TLS) results in R2 = 0.63 for the handheld GPS devices and R2 = 0.24 for the smartphone-based approach. RMSE for the comparison between crop height models (CHM) derived from PS and TLS data is 10.45 cm (GPS devices) and 14.69 cm (smartphones). Furthermore, the results indicate that incorporating participants' cognitive abilities in the data collection process potentially improves the quality data captured with the PS approach. The proposed PS methods serve as a fundament to collect agricultural parameters on field-level by incorporating local people. Combined with other methods such as remote sensing, PS opens new perspectives to support agricultural development.

Optimization and Characterization of the Friction Stir Welded Sheets of AA 5754-H111: Monitoring of the Quality of Joints with Thermographic Techniques

Directory of Open Access Journals (Sweden)

Luigi Alberto Ciro De Filippis

2017-10-01

Full Text Available Friction Stir Welding (FSW is a solid-state welding process, based on frictional and stirring phenomena, that offers many advantages with respect to the traditional welding methods. However, several parameters can affect the quality of the produced joints. In this work, an experimental approach has been used for studying and optimizing the FSW process, applied on 5754-H111 aluminum plates. In particular, the thermal behavior of the material during the process has been investigated and two thermal indexes, the maximum temperature and the heating rate of the material, correlated to the frictional power input, were investigated for different process parameters (the travel and rotation tool speeds configurations. Moreover, other techniques (micrographs, macrographs and destructive tensile tests were carried out for supporting in a quantitative way the analysis of the quality of welded joints. The potential of thermographic technique has been demonstrated both for monitoring the FSW process and for predicting the quality of joints in terms of tensile strength.

Optimization and Characterization of the Friction Stir Welded Sheets of AA 5754-H111: Monitoring of the Quality of Joints with Thermographic Techniques.

Science.gov (United States)

De Filippis, Luigi Alberto Ciro; Serio, Livia Maria; Palumbo, Davide; De Finis, Rosa; Galietti, Umberto

2017-10-11

Friction Stir Welding (FSW) is a solid-state welding process, based on frictional and stirring phenomena, that offers many advantages with respect to the traditional welding methods. However, several parameters can affect the quality of the produced joints. In this work, an experimental approach has been used for studying and optimizing the FSW process, applied on 5754-H111 aluminum plates. In particular, the thermal behavior of the material during the process has been investigated and two thermal indexes, the maximum temperature and the heating rate of the material, correlated to the frictional power input, were investigated for different process parameters (the travel and rotation tool speeds) configurations. Moreover, other techniques (micrographs, macrographs and destructive tensile tests) were carried out for supporting in a quantitative way the analysis of the quality of welded joints. The potential of thermographic technique has been demonstrated both for monitoring the FSW process and for predicting the quality of joints in terms of tensile strength.

Mobile Workforce, Mobile Technology, Mobile Threats

International Nuclear Information System (INIS)

Garcia, J.

2015-01-01

Mobile technologies' introduction into the world of safeguards business processes such as inspection creates tremendous opportunity for novel approaches and could result in a number of improvements to such processes. Mobile applications are certainly the wave of the future. The success of the application ecosystems has shown that users want full fidelity, highly-usable, simple purpose applications with simple installation, quick responses and, of course, access to network resources at all times. But the counterpart to opportunity is risk, and the widespread adoption of mobile technologies requires a deep understanding of the threats and vulnerabilities inherent in mobile technologies. Modern mobile devices can be characterized as small computers. As such, the threats against computing infrastructure apply to mobile devices. Meanwhile, the attributes of mobile technology that make it such an obvious benefit over traditional computing platforms all have elements of risk: pervasive, always-on networking; diverse ecosystems; lack of centralized control; constantly shifting technological foundations; intense competition among competitors in the marketplace; the scale of the installation base (from millions to billions); and many more. This paper will explore the diverse and massive environment of mobile, the number of attackers and vast opportunities for compromise. The paper will explain how mobile devices prove valuable targets to both advanced and persistent attackers as well as less-skilled casual hackers. Organized crime, national intelligence agencies, corporate espionage are all part of the landscape. (author)

Mobile Disdrometer Observations of Nocturnal Mesoscale Convective Systems During PECAN

Science.gov (United States)

Bodine, D. J.; Rasmussen, K. L.

2015-12-01

Understanding microphysical processes in nocturnal mesoscale convective systems (MCSs) is an important objective of the Plains Elevated Convection At Night (PECAN) experiment, which occurred from 1 June - 15 July 2015 in the central Great Plains region of the United States. Observations of MCSs were collected using a large array of mobile and fixed instrumentation, including ground-based radars, soundings, PECAN Integrated Sounding Arrays (PISAs), and aircraft. In addition to these observations, three mobile Parsivel disdrometers were deployed to obtain drop-size distribution (DSD) measurements to further explore microphysical processes in convective and stratiform regions of nocturnal MCSs. Disdrometers were deployed within close range of a multiple frequency network of mobile and fixed dual-polarization radars (5 - 30 km range), and near mobile sounding units and PISAs. Using mobile disdrometer and multiple-wavelength, dual-polarization radar data, microphysical properties of convective and stratiform regions of MCSs are investigated. The analysis will also examine coordinated Range-Height Indicator (RHI) scans over the disdrometers to elucidate vertical DSD structure. Analysis of dense observations obtained during PECAN in combination with mobile disdrometer DSD measurements contributes to a greater understanding of the structural characteristics and evolution of nocturnal MCSs.

Mechanisms of biliary stent clogging: confocal laser scanning and scanning electron microscopy.

Science.gov (United States)

van Berkel, A M; van Marle, J; Groen, A K; Bruno, M J

2005-08-01

Endoscopic insertion of plastic biliary endoprostheses is a well-established treatment for obstructive jaundice. The major limitation of this technique is late stent occlusion. In order to compare events involved in biliary stent clogging and identify the distribution of bacteria in unblocked stents, confocal laser scanning (CLS) and scanning electron microscopy (SEM) were carried out on two different stent materials - polyethylene (PE) and hydrophilic polymer-coated polyurethane (HCPC). Ten consecutive patients with postoperative benign biliary strictures were included in the study. Two 10-Fr stents 9 cm in length, one made of PE and the other of HCPC, were inserted. The stents were electively exchanged after 3 months and examined using CLS and SEM. No differences were seen between the two types of stent. The inner stent surface was covered with a uniform amorphous layer. On top of this layer, a biofilm of living and dead bacteria was found, which in most cases was unstructured. The lumen was filled with free-floating colonies of bacteria and crystals, surrounded by mobile laminar structures of mucus. An open network of large dietary fibers was seen in all of the stents. The same clogging events occurred in both PE and HCPC stents. The most remarkable observation was the identification of networks of large dietary fibers, resulting from duodenal reflux, acting as a filter. The build-up of this intraluminal framework of dietary fibers appears to be a major factor contributing to the multifactorial process of stent clogging.

X-ray and neutron interrogation of air cargo for mobile applications

Energy Technology Data Exchange (ETDEWEB)

Van Liew, Seth

2015-06-01

A system for scanning break-bulk cargo for mobile applications is presented. This combines a 140 kV multi-view, multi-energy X-ray system with 2.5 MeV neutrons. The system uses dual energy X-ray radiography with neutron radiography. The X-ray and neutron systems were designed to be collocated in a mobile environment. Various materials were interrogated with the intent of distinguishing threat materials such as explosives from similar benign materials. In particular, the identification of threats and bengins with nearly identical effective atomic numbers has been demonstrated.

X-ray and neutron interrogation of air cargo for mobile applications

International Nuclear Information System (INIS)

Van Liew, Seth

2015-01-01

A system for scanning break-bulk cargo for mobile applications is presented. This combines a 140 kV multi-view, multi-energy X-ray system with 2.5 MeV neutrons. The system uses dual energy X-ray radiography with neutron radiography. The X-ray and neutron systems were designed to be collocated in a mobile environment. Various materials were interrogated with the intent of distinguishing threat materials such as explosives from similar benign materials. In particular, the identification of threats and bengins with nearly identical effective atomic numbers has been demonstrated

Advances in 4D treatment planning for scanned particle beam therapy - report of dedicated workshops

NARCIS (Netherlands)

Bert, Christoph; Graeff, Christian; Riboldi, Marco; Nill, Simeon; Baroni, Guido; Knopf, Antje-Christin

2014-01-01

We report on recent progress in the field of mobile tumor treatment with scanned particle beams, as discussed in the latest editions of the 4D treatment planning workshop. The workshop series started in 2009, with about 20 people from 4 research institutes involved, all actively working on particle

Mobile Gaming and Student Interactions in a Science Center: The Future of Gaming in Science Education

Science.gov (United States)

Atwood-Blaine, Dana; Huffman, Douglas

2017-01-01

This article explores the impact of an augmented reality iPad-based mobile game, called The Great STEM Caper, on students' interaction at a science center. An open-source, location-based game platform called ARIS (i.e. Augmented Reality and Interactive Storytelling) was used to create an iPad-based mobile game. The game used QR scan codes and a…

Mobility management in mobile IP

Science.gov (United States)

Medidi, Sirisha; Golshani, Forouzan

2002-07-01

There is an emerging interest in integrating mobile wireless communication with the Internet based on the Ipv6 technology. Many issues introduced by the mobility of users arise when such an integration is attempted. This paper addresses the problem of mobility management, i.e., that of tracking the current IP addresses of mobile terminals and sustaining active IP connections as mobiles move. The paper presents some architectural and mobility management options for integrating wireless access to the Internet. We then present performance results for Mobile IPv4, route optimization and Mobile IPv6.

Structural Mobility, Exchange Mobility and Subgroup Consistent Mobility Measurement – US–German Mobility Measurements Revisited

OpenAIRE

C. SCHLUTER; D. VAN DE GAER

2008-01-01

We formalize the concept of structural mobility and use the framework of subgroup consistent mobility measurement to derive a relative and an absolute measure of mobility that is increasing both in upward structural mobility and exchange mobility. In our empirical illustration, we contribute substantively to the ongoing debate about mobility rankings between the USA and Germany.

3D Digital Smile Design With a Mobile Phone and Intraoral Optical Scanner.

Science.gov (United States)

Daher, René; Ardu, Stefano; Vjero, Osela; Krejci, Ivo

2018-06-01

Extraoral facial scanning using a mobile phone has emerged as a viable, cost-effective option for certain applications not requiring high precision, such as patient education and 3-dimensional (3D) digital smile design. This technological development is particularly promising for general practitioners (GPs) who may not be able to invest in expensive,complex digital impressioning devices. This article describes and illustrates a relatively simple and accessible workflow that avails digital 3D facial scanning benefits to GPs.

Mobile Learning Using Mobile Phones

Science.gov (United States)

Vicente, Paula

2013-01-01

The participation in mobile learning programs is conditioned by having/using mobile communication technology. Those who do not have or use such technology cannot participate in mobile learning programs. This study evaluates who are the most likely participants of mobile learning programs by examining the demographic profile and mobile phone usage…

Analysis of grease contamination influence on the internal radial clearance of ball bearings by thermographic inspection

Directory of Open Access Journals (Sweden)

Mišković Žarko Z.

2016-01-01

Full Text Available One of the most important factors influencing ball bearings service life is its internal radial clearance. However, this parameter is also very complex because it depends on applied radial load and ball bearings dimensions, surface finish and manufacturing materials. Thermal condition of ball bearings also significantly affects internal radial clearance. Despite many researches performed in order to find out relevant facts about different aspects of ball bearings thermal behaviour, only few of them are dealing with the real working conditions, where high concentration of solid contaminant particles is present. That’s why the main goal of research presented in this paper was to establish statistically significant correlation between ball bearings temperatures, their working time and concentration of contaminant particles in their grease. Because of especially difficult working conditions, the typical conveyor idlers bearings were selected as representative test samples and appropriate solid particles from open pit coal mines were used as artificial contaminants. Applied experimental methodology included thermographic inspection, as well as usage of custom designed test rig for ball bearings service life testing. Finally, by obtained experimental data processing in advanced software, statistically significant mathematical correlation between mentioned bearings characteristics was determined and applied in commonly used internal radial clearance equation. That is the most important contribution of performed research - the new equation and methodology for ball bearings internal clearance determination which could be used for eventual improvement of existing bearings service life equations. [Projekat Ministarstva nauke Republike Srbije, br. TR35029 i br. TR14033

Accuracy assessment of a mobile terrestrial lidar survey at Padre Island National Seashore

Science.gov (United States)

Lim, Samsung; Thatcher, Cindy A.; Brock, John C.; Kimbrow, Dustin R.; Danielson, Jeffrey J.; Reynolds, B.J.

2013-01-01

The higher point density and mobility of terrestrial laser scanning (light detection and ranging (lidar)) is desired when extremely detailed elevation data are needed for mapping vertically orientated complex features such as levees, dunes, and cliffs, or when highly accurate data are needed for monitoring geomorphic changes. Mobile terrestrial lidar scanners have the capability for rapid data collection on a larger spatial scale compared with tripod-based terrestrial lidar, but few studies have examined the accuracy of this relatively new mapping technology. For this reason, we conducted a field test at Padre Island National Seashore of a mobile lidar scanner mounted on a sport utility vehicle and integrated with a position and orientation system. The purpose of the study was to assess the vertical and horizontal accuracy of data collected by the mobile terrestrial lidar system, which is georeferenced to the Universal Transverse Mercator coordinate system and the North American Vertical Datum of 1988. To accomplish the study objectives, independent elevation data were collected by conducting a high-accuracy global positioning system survey to establish the coordinates and elevations of 12 targets spaced throughout the 12 km transect. These independent ground control data were compared to the lidar scanner-derived elevations to quantify the accuracy of the mobile lidar system. The performance of the mobile lidar system was also tested at various vehicle speeds and scan density settings (e.g. field of view and linear point spacing) to estimate the optimal parameters for desired point density. After adjustment of the lever arm parameters, the final point cloud accuracy was 0.060 m (east), 0.095 m (north), and 0.053 m (height). The very high density of the resulting point cloud was sufficient to map fine-scale topographic features, such as the complex shape of the sand dunes.

Mobile Probes in Mobile Learning

DEFF Research Database (Denmark)

Ørngreen, Rikke; Blomhøj, Ulla; Duvaa, Uffe

In this paper experiences from using mobile probes in educational design of a mobile learning application is presented. The probing process stems from the cultural probe method, and was influenced by qualitative interview and inquiry approaches. In the project, the mobile phone was not only acting...... as an agent for acquiring empirical data (as the situation in hitherto mobile probe settings) but was also the technological medium for which data should say something about (mobile learning). Consequently, not only the content of the data but also the ways in which data was delivered and handled, provided...... a valuable dimension for investigating mobile use. The data was collected at the same time as design activities took place and the collective data was analysed based on user experience goals and cognitive processes from interaction design and mobile learning. The mobile probe increased the knowledge base...

Monitoring marginal erosion in hydroelectric reservoirs with terrestrial mobile laser scanner

Directory of Open Access Journals (Sweden)

A. M. G. Tommaselli

2014-06-01

Full Text Available Marginal erosions in reservoirs of hydroelectric plants have caused economic and environmental problems concerning hydroelectric power generation, reduction of productive areas and devaluing land parcels. The real extension and dynamics of these erosion processes are not well known for Brazilian reservoirs. To objectively assess these problems Unesp (Univ Estadual Paulista and Duke Energy are developing a joint project which aims at the monitoring the progression of some erosive processes and understanding the causes and the dynamics of this phenomenon. Mobile LASER scanning was considered the most suitable alternative for the challenges established in the project requirements. A MDL DynaScan Mobile LASER M150 scanner was selected which uses RTK for real time positioning integrated to an IMU, enabling instantaneous generation of georeferenced point clouds. Two different reservoirs were choose for monitoring: Chavantes (storage plant and Rosana (run-of-river plant, both in the Paranapanema River, border of São Paulo and Paraná States, Brazil. The monitoring areas are scanned quarterly and analysed with base on the point cloud, meshes, contours and cross sections. Cross sections are used to visualize and compute the rate and the dynamics of erosion. Some examples and quantitative results are presented along with an analysis of the proposed technique. Some recommendations to improve the field work and latter data processing are also introduced.

A brick-architecture-based mobile under-vehicle inspection system

Science.gov (United States)

Qian, Cheng; Page, David; Koschan, Andreas; Abidi, Mongi

2005-05-01

In this paper, a mobile scanning system for real-time under-vehicle inspection is presented, which is founded on a "Brick" architecture. In this "Brick" architecture, the inspection system is basically decomposed into bricks of three kinds: sensing, mobility, and computing. These bricks are physically and logically independent and communicate with each other by wireless communication. Each brick is mainly composed by five modules: data acquisition, data processing, data transmission, power, and self-management. These five modules can be further decomposed into submodules where the function and the interface are well-defined. Based on this architecture, the system is built by four bricks: two sensing bricks consisting of a range scanner and a line CCD, one mobility brick, and one computing brick. The sensing bricks capture geometric data and texture data of the under-vehicle scene, while the mobility brick provides positioning data along the motion path. Data of these three modalities are transmitted to the computing brick where they are fused and reconstruct a 3D under-vehicle model for visualization and danger inspection. This system has been successfully used in several military applications and proved to be an effective safer method for national security.

An intelligent detection method for high-field asymmetric waveform ion mobility spectrometry.

Science.gov (United States)

Li, Yue; Yu, Jianwen; Ruan, Zhiming; Chen, Chilai; Chen, Ran; Wang, Han; Liu, Youjiang; Wang, Xiaozhi; Li, Shan

2018-04-01

In conventional high-field asymmetric waveform ion mobility spectrometry signal acquisition, multi-cycle detection is time consuming and limits somewhat the technique's scope for rapid field detection. In this study, a novel intelligent detection approach has been developed in which a threshold was set on the relative error of α parameters, which can eliminate unnecessary time spent on detection. In this method, two full-spectrum scans were made in advance to obtain the estimated compensation voltage at different dispersion voltages, resulting in a narrowing down of the whole scan area to just the peak area(s) of interest. This intelligent detection method can reduce the detection time to 5-10% of that of the original full-spectrum scan in a single cycle.

Abrechnung mobiler Dienste im Mobile-Payment-Referenzmodell

OpenAIRE

Pousttchi, Key; Wiedemann, Dietmar Georg

2005-01-01

The purpose of the paper is to analyze mobile payments in the mobile commerce scenario. Therefore, we first classify the mobile payment in the mobile commerce scenario by explaining general offer models, charging concepts, and intermediaries. Second, we describe the mobile payment reference model, especially, the mobile payment reference organization model and different mobile payment standard types. Finally, we conclude our findings.

A Novel Low-Cost Adaptive Scanner Concept for Mobile Robots

Directory of Open Access Journals (Sweden)

Ivo Stančić

2014-09-01

Full Text Available A fundamental problem in mobile robot applications is the need for accurate knowledge of the position of a vehicle for localizing itself and for avoiding obstacles in its path. In the search for a solution to this problem, researchers and engineers have developed different sensors, systems and techniques. Modern mobile robots relay information obtained from a variety of sensors and sophisticated data fusion algorithms. In this paper, a novel concept for a low-cost adaptive scanner based on a projected light pattern is proposed. The main advantage of the proposed system is its adaptivity, which enables the rapid scanning of the robot’s surroundings in search of obstacles and a more detailed scan of a single object to retrieve its surface configuration and perform some limited analyses. This paper addresses the concept behind such a scanner, where a proof-of-concept is achieved using an office DLP projector. During the measurements, the accuracy of the proposed system was tested on obstacles and objects with known configurations. The obtained results are presented and analyzed, and conclusions about the system’s performance and possible improvements are discussed.

Comparison of High-Flexion Fixed-Bearing and High-Flexion Mobile-Bearing Total Knee Arthroplasties-A Prospective Randomized Study.

Science.gov (United States)

Kim, Young-Hoo; Park, Jang-Won; Kim, Jun-Shik

2018-01-01

There is none, to our knowledge, about comparison of high-flexion fixed-bearing and high-flexion mobile-bearing total knee arthroplasties (TKAs) in the same patients. The purpose of this study was to determine whether clinical results; radiographic and computed tomographic scan results; and the survival rate of a high-flexion mobile-bearing TKA is better than that of a high-flexion fixed-bearing TKA. The present study consisted of 92 patients (184 knees) who underwent same-day bilateral TKA. Of those, 17 were men and 75 were women. The mean age at the time of index arthroplasty was 61.5 ± 8.3 years (range 52-65 years). The mean body mass index was 26.2 ± 3.3 kg/m 2 (range 23-34 kg/m 2 ). The mean follow-up was 11.2 years (range 10-12 years). The Knee Society knee scores (93 vs 92 points; P = .531) and function scores (80 vs 80 points; P = 1.000), WOMAC scores (14 vs 15 points; P = .972), and UCLA activity scores (6 vs 6 points; P = 1.000) were not different between the 2 groups at 12 years follow-up. There were no differences in any radiographic and CT scan parameters between the 2 groups. Kaplan-Meier survivorship of the TKA component was 98% (95% confidence interval, 93-100) in the high-flexion fixed-bearing TKA group and 99% (95% confidence interval, 94-100) in the high-flexion mobile-bearing TKA group 12 years after the operation. We found no benefit to mobile-bearing TKA in terms of pain, function, radiographic and CT scan results, and survivorship. Longer-term follow-up is necessary to prove the benefit of the high-flexion mobile-bearing TKA over the high-flexion fixed-bearing TKA. Copyright © 2017 Elsevier Inc. All rights reserved.

An interchangeable scanning Hall probe/scanning SQUID microscope

International Nuclear Information System (INIS)

Tang, Chiu-Chun; Lin, Hui-Ting; Wu, Sing-Lin; Chen, Tse-Jun; Wang, M. J.; Ling, D. C.; Chi, C. C.; Chen, Jeng-Chung

2014-01-01

We have constructed a scanning probe microscope for magnetic imaging, which can function as a scanning Hall probe microscope (SHPM) and as a scanning SQUID microscope (SSM). The scanning scheme, applicable to SHPM and SSM, consists of a mechanical positioning (sub) micron-XY stage and a flexible direct contact to the sample without a feedback control system for the Z-axis. With the interchangeable capability of operating two distinct scanning modes, our microscope can incorporate the advantageous functionalities of the SHPM and SSM with large scan range up to millimeter, high spatial resolution (⩽4 μm), and high field sensitivity in a wide range of temperature (4.2 K-300 K) and magnetic field (10 −7 T-1 T). To demonstrate the capabilities of the system, we present magnetic images scanned with SHPM and SSM, including a RbFeB magnet and a nickel grid pattern at room temperature, surface magnetic domain structures of a La 2/3 Ca 1/3 MnO 3 thin film at 77 K, and superconducting vortices in a striped niobium film at 4.2 K

Investigation of the exposure level of electromagnetic fields produced by mobile telephone base stations

International Nuclear Information System (INIS)

Abukassem, I.; Kharita, M. H.

2010-12-01

The aim of this work is to investigate the real values of microwave level distribution and propagation in the locality around samples of mobile phone base station, and to compare the results with the exposure restriction limits recommenced by the International Commission on Non Ionizing Radiation Protection (ICNIRP). Measurements were performed using special meters for microwaves; the first (Narda SRM-3000) is used for electromagnetic waves frequency spectrum scanning and the second (NARDA) emr 300) determine the level of electric and magnetic fields and the power density of these waves nearby any sort of transmitters. Samples of different kinds of mobile phone base station were chosen to cover important zones of Damascus, and the region around each base station was also scanned in the emission direction and according to accessibility into the studies positions. Results showed that the signal level in all measured points is lower than the ICNIRP restriction level, but for few points the detected microwave level has relatively important values. The signal level inside building situated partially in the emission direction of the base station transmitters decreases stepwise and walls reduce considerably the signal intensity. To realize these kind of field studies in the best way and obtain the maximum profits for all people, the properties and operating system of transmitters used in mobile phone base station must be known, and therefore, it is very important to achieve a transparent collaboration between research laboratory and mobile phone company. (author)

Best Signal Quality in Cellular Networks: Asymptotic Properties and Applications to Mobility Management in Small Cell Networks

Directory of Open Access Journals (Sweden)

Baccelli François

2010-01-01

Full Text Available The quickly increasing data traffic and the user demand for a full coverage of mobile services anywhere and anytime are leading mobile networking into a future of small cell networks. However, due to the high-density and randomness of small cell networks, there are several technical challenges. In this paper, we investigate two critical issues: best signal quality and mobility management. Under the assumptions that base stations are uniformly distributed in a ring-shaped region and that shadowings are lognormal, independent, and identically distributed, we prove that when the number of sites in the ring tends to infinity, then (i the maximum signal strength received at the center of the ring tends in distribution to a Gumbel distribution when properly renormalized, and (ii it is asymptotically independent of the interference. Using these properties, we derive the distribution of the best signal quality. Furthermore, an optimized random cell scanning scheme is proposed, based on the evaluation of the optimal number of sites to be scanned for maximizing the user data throughput.

Towards the Automatic Scanning of Indoors with Robots

Directory of Open Access Journals (Sweden)

Antonio Adán

2015-05-01

Full Text Available This paper is framed in both 3D digitization and 3D data intelligent processing research fields. Our objective is focused on developing a set of techniques for the automatic creation of simple three-dimensional indoor models with mobile robots. The document presents the principal steps of the process, the experimental setup and the results achieved. We distinguish between the stages concerning intelligent data acquisition and 3D data processing. This paper is focused on the first stage. We show how the mobile robot, which carries a 3D scanner, is able to, on the one hand, make decisions about the next best scanner position and, on the other hand, navigate autonomously in the scene with the help of the data collected from earlier scans. After this stage, millions of 3D data are converted into a simplified 3D indoor model. The robot imposes a stopping criterion when the whole point cloud covers the essential parts of the scene. This system has been tested under real conditions indoors with promising results. The future is addressed to extend the method in much more complex and larger scenarios.

Lock-in thermography, penetrant inspection, and scanning electron microscopy for quantitative evaluation of open micro-cracks at the tooth-restoration interface

Science.gov (United States)

Streza, M.; Hodisan, I.; Prejmerean, C.; Boue, C.; Tessier, Gilles

2015-03-01

The evaluation of a dental restoration in a non-invasive way is of paramount importance in clinical practice. The aim of this study was to assess the minimum detectable open crack at the cavity-restorative material interface by the lock-in thermography technique, at laser intensities which are safe for living teeth. For the analysis of the interface, 18 box-type class V standardized cavities were prepared on the facial and oral surfaces of each tooth, with coronal margins in enamel and apical margins in dentine. The preparations were restored with the Giomer Beautifil (Shofu) in combination with three different adhesive systems. Three specimens were randomly selected from each experimental group and each slice has been analysed by visible, infrared (IR), and scanning electron microscopy (SEM). Lock-in thermography showed the most promising results in detecting both marginal and internal defects. The proposed procedure leads to a diagnosis of micro-leakages having openings of 1 µm, which is close to the diffraction limit of the IR camera. Clinical use of a thermographic camera in assessing the marginal integrity of a restoration becomes possible. The method overcomes some drawbacks of standard SEM or dye penetration testing. The results support the use of an IR camera in dentistry, for the diagnosis of micro-gaps at bio-interfaces.

An interchangeable scanning Hall probe/scanning SQUID microscope

Energy Technology Data Exchange (ETDEWEB)

Tang, Chiu-Chun; Lin, Hui-Ting; Wu, Sing-Lin [Department of Physics, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Chen, Tse-Jun; Wang, M. J. [Institute of Astronomy and Astrophysics, Academia Sinica, Taipei 10617, Taiwan (China); Ling, D. C. [Department of Physics, Tamkang University, Tamsui Dist., New Taipei City 25137, Taiwan (China); Chi, C. C.; Chen, Jeng-Chung [Department of Physics, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Frontier Research Center on Fundamental and Applied Sciences of Matters, National Tsing Hua University, Hsinchu 30013, Taiwan (China)

2014-08-15

We have constructed a scanning probe microscope for magnetic imaging, which can function as a scanning Hall probe microscope (SHPM) and as a scanning SQUID microscope (SSM). The scanning scheme, applicable to SHPM and SSM, consists of a mechanical positioning (sub) micron-XY stage and a flexible direct contact to the sample without a feedback control system for the Z-axis. With the interchangeable capability of operating two distinct scanning modes, our microscope can incorporate the advantageous functionalities of the SHPM and SSM with large scan range up to millimeter, high spatial resolution (⩽4 μm), and high field sensitivity in a wide range of temperature (4.2 K-300 K) and magnetic field (10{sup −7} T-1 T). To demonstrate the capabilities of the system, we present magnetic images scanned with SHPM and SSM, including a RbFeB magnet and a nickel grid pattern at room temperature, surface magnetic domain structures of a La{sub 2/3}Ca{sub 1/3}MnO{sub 3} thin film at 77 K, and superconducting vortices in a striped niobium film at 4.2 K.

Mobile Customer Relationship Management and Mobile Security

Science.gov (United States)

Sanayei, Ali; Mirzaei, Abas

The purpose of this study is twofold. First, in order to guarantee a coherent discussion about mobile customer relationship management (mCRM), this paper presents a conceptualization of mCRM delineating its unique characteristics because of Among the variety of mobile services, considerable attention has been devoted to mobile marketing and in particular to mobile customer relationship management services. Second, the authors discusses the security risks in mobile computing in different level(user, mobile device, wireless network,...) and finally we focus on enterprise mobile security and it's subgroups with a series of suggestion and solution for improve mobile computing security.

Error analysis of motion correction method for laser scanning of moving objects

Science.gov (United States)

Goel, S.; Lohani, B.

2014-05-01

The limitation of conventional laser scanning methods is that the objects being scanned should be static. The need of scanning moving objects has resulted in the development of new methods capable of generating correct 3D geometry of moving objects. Limited literature is available showing development of very few methods capable of catering to the problem of object motion during scanning. All the existing methods utilize their own models or sensors. Any studies on error modelling or analysis of any of the motion correction methods are found to be lacking in literature. In this paper, we develop the error budget and present the analysis of one such `motion correction' method. This method assumes availability of position and orientation information of the moving object which in general can be obtained by installing a POS system on board or by use of some tracking devices. It then uses this information along with laser scanner data to apply correction to laser data, thus resulting in correct geometry despite the object being mobile during scanning. The major application of this method lie in the shipping industry to scan ships either moving or parked in the sea and to scan other objects like hot air balloons or aerostats. It is to be noted that the other methods of "motion correction" explained in literature can not be applied to scan the objects mentioned here making the chosen method quite unique. This paper presents some interesting insights in to the functioning of "motion correction" method as well as a detailed account of the behavior and variation of the error due to different sensor components alone and in combination with each other. The analysis can be used to obtain insights in to optimal utilization of available components for achieving the best results.

Mobile Payments : Comparison of Mobile Wallet Concepts

OpenAIRE

Narayan, Srikant

2013-01-01

Mobile payments are an emerging trend and an alternative to traditional payment methods. Mobile payments involve the usage of the mobile phone to handle credit transfers during purchase of goods and peer to peer money transfers referred to as mobile wallet service, instead of depending on bank cards and cash. In this scenario, while the mobile wallet industry still being in its infancy there exist a few drivers of mobile wallet solutions aiming to create a de-facto standard in the mobile mark...

NEW SCANNING DEVICE FOR SCANNING TUNNELING MICROSCOPE APPLICATIONS

NARCIS (Netherlands)

SAWATZKY, GA; Koops, Karl Richard

A small, single piezo XYZ translator has been developed. The device has been used as a scanner for a scanning tunneling microscope and has been tested successfully in air and in UHV. Its simple design results in a rigid and compact scanning unit which permits high scanning rates.

Mobile video with mobile IPv6

CERN Document Server

Minoli, Daniel

2012-01-01

Increased reliance on mobile devices and streaming of video content are two of the most recent changes that have led those in the video distribution industry to be concerned about the shifting or erosion of traditional advertising revenues. Infrastructure providers also need to position themselves to take advantage of these trends. Mobile Video with Mobile IPv6provides an overview of the current mobile landscape, then delves specifically into the capabilities and operational details of IPv6. The book also addresses 3G and 4G services, the application of Mobile IPv6 to streaming and other mobil

Nuclear Scans

Science.gov (United States)

Nuclear scans use radioactive substances to see structures and functions inside your body. They use a special ... images. Most scans take 20 to 45 minutes. Nuclear scans can help doctors diagnose many conditions, including ...

Evaluation of mobile phone addiction level and sleep quality in university students.

Science.gov (United States)

Sahin, Sevil; Ozdemir, Kevser; Unsal, Alaattin; Temiz, Nazen

2013-07-01

To determine the mobile phone addiction level in university students, to examine several associated factors and to evaluate the relation between the addiction level and sleep quality. The study is a cross-sectional research conducted on the students of the Sakarya University between 01 November 2012 and 01 February 2013. The study group included 576 students. The Problematic Mobile Phone Use Scale was used for evaluating the mobile phone addiction level and the Pittsburgh Sleep Quality Index for assessing the sleep quality. Mann-Whitney U test, Kruskal-Wallis test and Spearman's Correlation Analysis were used for analyzing the data. The study group consisted of 296 (51.4%) females and 208 (48.6%) males. The mean age was 20.83 ± 1.90 years (min:17, max:28). The addiction level was determined to be higher in the second-year students, those with poor family income, those with type A personality, those whose age for first mobile phone is 13 and below and those whose duration of daily mobile phone use is above 5 hours (p phone addiction level (p addiction level. It was concluded that referring the students with suspected addiction to advanced healthcare facilities, performing occasional scans for early diagnosis and informing the students about controlled mobile phone use would be useful.

Compact scanning transmission x-ray microscope at the photon factory

International Nuclear Information System (INIS)

Takeichi, Yasuo; Inami, Nobuhito; Ono, Kanta; Suga, Hiroki; Takahashi, Yoshio

2016-01-01

We report the design and performance of a compact scanning transmission X-ray microscope developed at the Photon Factory. Piezo-driven linear stages are used as coarse stages of the microscope to realize excellent compactness, mobility, and vibrational and thermal stability. An X-ray beam with an intensity of ∼10 7 photons/s was focused to a diameter of ∼40 nm at the sample. At the soft X-ray undulator beamline used with the microscope, a wide range of photon energies (250–1600 eV) is available. The microscope has been used to research energy materials and in environmental sciences

Mobile phones and mobile communication

DEFF Research Database (Denmark)

Ling, Richard; Donner, Jonathan

With staggering swiftness, the mobile phone has become a fixture of daily life in almost every society on earth. In 2007, the world had over 3 billion mobile subscriptions. Prosperous nations boast of having more subscriptions than people. In the developing world, hundreds of millions of people who...... could never afford a landline telephone now have a mobile number of their own. With a mobile in our hand many of us feel safer, more productive, and more connected to loved ones, but perhaps also more distracted and less involved with things happening immediately around us. Written by two leading...... researchers in the field, this volume presents an overview of the mobile telephone as a social and cultural phenomenon. Research is summarized and made accessible though detailed descriptions of ten mobile users from around the world. These illustrate popular debates, as well as deeper social forces at work...

Boosting antenatal care attendance and number of hospital deliveries among pregnant women in rural communities: a community initiative in Ghana based on mobile phones applications and portable ultrasound scans.

Science.gov (United States)

Amoah, Benjamin; Anto, Evelyn A; Osei, Prince K; Pieterson, Kojo; Crimi, Alessandro

2016-06-14

The World Health Organization has recommended at least four antenatal care (ANC) visits and skilled attendants at birth. Most pregnant women in rural communities in low-income countries do not achieve the minimum recommended visits and deliver without skilled attendants. With the aim of increasing number of ANC visits, reducing home deliveries, and supplementing care given by ANC clinics, a proposed system based on low-cost mobile phones and portable ultrasound scan machines was piloted. A sample of 323 pregnant women from four rural communities in the Central Region of Ghana were followed within a 11-month project. In each community, at least one health worker was trained and equipped with a mobile phone to promote ANC and hospital deliveries in her own community. If women cannot attend ANC, technicians acquired scans by using portable ultrasound machines in her community directly and sent them almost in real time to be analyzed by a gynecologist in an urban hospital. A preliminary survey to assess ANC status preceding the pilot study was conducted. During this, one hundred women who had had pregnancies within five years prior to the study were interviewed. The preliminary survey showed that women who attended ANC were less likely to have a miscarriage and more likely to have delivery at hospital or clinic than those who did not, and women who attained at least four ANC visits were less likely to practice self-medication. Among the women involved in the project, 40 gave birth during the period of observation. The proposed prenatal care approach showed that 62.5 % of pregnant women who gave birth during the observation period included in the project (n=40) had their labor attended in clinics or hospitals as against 37.5 % among the cases reported in the pre-survey. One case of ectopic and two cases of breech pregnancies were detected during the pilot through the proposed approach, and appropriate medical interventions were sought. Our results show that the proposed

Mobile social phonebooks - Mobile phone user perceptions and practical implications for mobile operators

OpenAIRE

Karikoski, Juuso; Mäkinen, Olli

2012-01-01

Julkaisun kokoteksti on luettavissa vain Aalto-tunnuksilla. Please note that access to the fulltext is limited to Aalto staff and students. We introduce a term called mobile social phonebook, which refers to the integration of traditional mobile phone contacts with contacts from mobile Internet communication services that is happening in the mobile device’s phonebook. First, mobile phone user perceptions towards mobile social phonebooks are studied by means of semi-structured interviews...

Revealing the 1 nm/s Extensibility of Nanoscale Amorphous Carbon in a Scanning Electron Microscope

DEFF Research Database (Denmark)

Zhang, Wei

2013-01-01

In an ultra-high vacuum scanning electron microscope, the edged branches of amorphous carbon film (∼10 nm thickness) can be continuously extended with an eye-identifying speed (on the order of ∼1 nm/s) under electron beam. Such unusual mobility of amorphous carbon may be associated with deformation...... promoted by the electric field, which resulted from an inner secondary electron potential difference from the main trunk of carbon film to the tip end of branches under electron beam. This result demonstrates importance of applying electrical effects to modify properties of carbon materials. It may have...... positive implications to explore some amorphous carbon as electron field emission device. SCANNING 35: 261-264, 2013. © 2012 Wiley Periodicals, Inc....

33 CFR 165.835 - Security Zone; Port of Mobile, Mobile Ship Channel, Mobile, AL.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Security Zone; Port of Mobile, Mobile Ship Channel, Mobile, AL. 165.835 Section 165.835 Navigation and Navigable Waters COAST GUARD... § 165.835 Security Zone; Port of Mobile, Mobile Ship Channel, Mobile, AL. (a) Definition. As used in...

Brain PET scan

Science.gov (United States)

... results on a PET scan. Blood sugar or insulin levels may affect the test results in people with diabetes . PET scans may be done along with a CT scan. This combination scan is called a PET/CT. Alternative Names Brain positron emission tomography; PET scan - brain References Chernecky ...

Improving Inpatient Surveys: Web-Based Computer Adaptive Testing Accessed via Mobile Phone QR Codes.

Science.gov (United States)

Chien, Tsair-Wei; Lin, Weir-Sen

2016-03-02

The National Health Service (NHS) 70-item inpatient questionnaire surveys inpatients on their perceptions of their hospitalization experience. However, it imposes more burden on the patient than other similar surveys. The literature shows that computerized adaptive testing (CAT) based on item response theory can help shorten the item length of a questionnaire without compromising its precision. Our aim was to investigate whether CAT can be (1) efficient with item reduction and (2) used with quick response (QR) codes scanned by mobile phones. After downloading the 2008 inpatient survey data from the Picker Institute Europe website and analyzing the difficulties of this 70-item questionnaire, we used an author-made Excel program using the Rasch partial credit model to simulate 1000 patients' true scores followed by a standard normal distribution. The CAT was compared to two other scenarios of answering all items (AAI) and the randomized selection method (RSM), as we investigated item length (efficiency) and measurement accuracy. The author-made Web-based CAT program for gathering patient feedback was effectively accessed from mobile phones by scanning the QR code. We found that the CAT can be more efficient for patients answering questions (ie, fewer items to respond to) than either AAI or RSM without compromising its measurement accuracy. A Web-based CAT inpatient survey accessed by scanning a QR code on a mobile phone was viable for gathering inpatient satisfaction responses. With advances in technology, patients can now be offered alternatives for providing feedback about hospitalization satisfaction. This Web-based CAT is a possible option in health care settings for reducing the number of survey items, as well as offering an innovative QR code access.

Mobile Cloud-Computing-Based Healthcare Service by Noncontact ECG Monitoring

Directory of Open Access Journals (Sweden)

Ee-May Fong

2013-12-01

Full Text Available Noncontact electrocardiogram (ECG measurement technique has gained popularity these days owing to its noninvasive features and convenience in daily life use. This paper presents mobile cloud computing for a healthcare system where a noncontact ECG measurement method is employed to capture biomedical signals from users. Healthcare service is provided to continuously collect biomedical signals from multiple locations. To observe and analyze the ECG signals in real time, a mobile device is used as a mobile monitoring terminal. In addition, a personalized healthcare assistant is installed on the mobile device; several healthcare features such as health status summaries, medication QR code scanning, and reminders are integrated into the mobile application. Health data are being synchronized into the healthcare cloud computing service (Web server system and Web server dataset to ensure a seamless healthcare monitoring system and anytime and anywhere coverage of network connection is available. Together with a Web page application, medical data are easily accessed by medical professionals or family members. Web page performance evaluation was conducted to ensure minimal Web server latency. The system demonstrates better availability of off-site and up-to-the-minute patient data, which can help detect health problems early and keep elderly patients out of the emergency room, thus providing a better and more comprehensive healthcare cloud computing service.

Mobile Semiotics - signs and mobilities

DEFF Research Database (Denmark)

Jensen, Ole B.

a potential for mobilities studies if the awareness of seeing the environment as a semiotic layer and system can be sensitized to the insights of the ‘mobilities turn’. Empirically the paper tentatively explores the usefulness of a mobile semiotics approach to cases such as street signage, airport design...

Radionuclide scanning

International Nuclear Information System (INIS)

Shapiro, B.

1986-01-01

Radionuclide scanning is the production of images of normal and diseased tissues and organs by means of the gamma-ray emissions from radiopharmaceutical agents having specific distributions in the body. The gamma rays are detected at the body surface by a variety of instruments that convert the invisible rays into visible patterns representing the distribution of the radionuclide in the body. The patterns, or images, obtained can be interpreted to provide or to aid diagnoses, to follow the course of disease, and to monitor the management of various illnesses. Scanning is a sensitive technique, but its specificity may be low when interpreted alone. To be used most successfully, radionuclide scanning must be interpreted in conjunction with other techniques, such as bone radiographs with bone scans, chest radiographs with lung scans, and ultrasonic studies with thyroid scans. Interpretation is also enhanced by providing pertinent clinical information because the distribution of radiopharmaceutical agents can be altered by drugs and by various procedures besides physiologic and pathologic conditions. Discussion of the patient with the radionuclide scanning specialist prior to the study and review of the results with that specialist after the study are beneficial

A Novel Complementary Method for the Point-Scan Nondestructive Tests Based on Lamb Waves

Directory of Open Access Journals (Sweden)

Rahim Gorgin

2014-01-01

Full Text Available This study presents a novel area-scan damage identification method based on Lamb waves which can be used as a complementary method for point-scan nondestructive techniques. The proposed technique is able to identify the most probable locations of damages prior to point-scan test which lead to decreasing the time and cost of inspection. The test-piece surface was partitioned with some smaller areas and the damage probability presence of each area was evaluated. A0 mode of Lamb wave was generated and collected using a mobile handmade transducer set at each area. Subsequently, a damage presence probability index (DPPI based on the energy of captured responses was defined for each area. The area with the highest DPPI value highlights the most probable locations of damages in test-piece. Point-scan nondestructive methods can then be used once these areas are found to identify the damage in detail. The approach was validated by predicting the most probable locations of representative damages including through-thickness hole and crack in aluminum plates. The obtained experimental results demonstrated the high potential of developed method in defining the most probable locations of damages in structures.

A user interface for mobile robotized tele-echography

International Nuclear Information System (INIS)

Triantafyllidis, G.A.; Thomos, N.; Canero, C.; Vieyres, P.; Strintzis, M.G.

2006-01-01

Ultrasound imaging allows the evaluation of the degree of emergency of a patient. However, in many situations no experienced sonographer is available to perform such echography. To cope with this issue, the OTELO project 'mObile Tele-Echography using an ultra-Light rObot' (OTELO) aims to develop a fully integrated end-to-end mobile tele-echography system using an ultralight, remotely controlled six degree-of-freedom (DOF) robot. In this context, this paper deals with the user interface environment of the OTELO system, composed by the following parts: an ultrasound video transmission system providing real-time images of the scanned area at each moment, an audio/video conference to communicate with the paramedical assistant and the patient, and finally a virtual reality environment, providing visual and haptic feedback to the expert, while capturing the expert's hand movements with a one-DOF hand free input device

Belgium's burning coal tips. Coupling thermographic ASTER imagery with topography to map debris slide susceptibility

Energy Technology Data Exchange (ETDEWEB)

Nyssen, Jan; Diependaele, Stijn; Goossens, Rudi [Ghent Univ. (Belgium). Dept. of Geography

2012-03-15

Burning coal tips and the debris slides induced by this combustion are a potential danger for local residents and visitors, and a method is required to identify areas of susceptibility. The relatively easy circulation of air, enhanced by the poor compaction of the spoil heaps, and the exothermic reaction of pyrite with oxygen may ignite coal tips. Rainwater infiltration and subsequent evaporation inside burning coal tips may create steam pressure, which, combined with humidity and slope steepness can then trigger landsliding. Based on mapping of debris slides and susceptibility factors such as burning (represented by positive surface temperature anomalies on thermographic imagery) and slope gradient, this study aims to define thresholds for debris slide susceptibility on coal tips and to map potential debris slide source areas on spoil heaps. The Belgian coal tips were used as study area. A DTM as well as ASTER Kinetic Surface Temperature products were used to measure slope gradients and temperature anomaly. Locations with typical characteristics of combustion (heat, red soil colour, steam and gases), and debris slides were recorded in the field, and were used to identify thresholds beyond which debris sliding is generally observed: a temperature anomaly of > 0.5 K, when comparing the debris slide areas to the average temperature of the coal tip, and a slope gradient {>=} 28 . The susceptibility zones for debris slide detachment were mapped by considering the imagery pixels that exceeded the thresholds for temperature and slope gradient; the results fitted well when compared with the observed debris slides. The method can be improved by using more coal tips for calibration, and by taking into account rain depth and slope aspect. (orig.)

Mobile lifestyles : Conceptualizing heterogeneity in mobile youth culture

NARCIS (Netherlands)

Vanden Abeele, M.M.P.

2014-01-01

Adolescents’ characteristic understanding and use of mobile phones have led observers to speak of a “mobile youth culture.” This article explores whether we can differentiate lifestyles within mobile youth culture. We construct a user typology of Flemish adolescent mobile phone users based on mobile

The Iqmulus urban showcase : Automatic tree classification and identification in huge mobile mapping point clouds

NARCIS (Netherlands)

Boehm, J; Bredif, M.; Gierlinger, T.; Krämer, M.; Lindenbergh, R.C.; Liu, K.; Michel, F.; Sirmacek, B.

2016-01-01

Current 3D data capturing as implemented on for example airborne or mobile laser scanning systems is able to efficiently sample the surface of a city by billions of unselective points during one working day. What is still difficult is to extract and visualize meaningful information hidden in

A Novel Pedicle Screw with Mobile Connection: A Pilot Study

Directory of Open Access Journals (Sweden)

Yasuaki Tokuhashi

2014-01-01

Full Text Available To prevent adjacent disc problems after spinal fusion, a pedicle screw with a mobile junction between the head and threaded shaft was newly developed. The threaded shaft of the screw has 10 degrees mobility in all directions, but its structure is to prevent abnormal translation and tilting. This screw was evaluated as follows: (1 endurance test: 106 times rotational stress was applied; (2 biological reactions: novel screws with a mobile head and conventional screws with a fixed head were inserted into the bilateral pedicles of the L3, L4, and L5 in two mini pigs with combination. Eight months after surgery, vertebral units with the screw rod constructs were collected. After CT scan, the soft and bony tissues around the screws were examined grossly and histologically. As a result, none of the screws broke during the endurance test stressing. The mean amount of abrasion wear was 0.0338 g. In the resected mini pig section, though zygapophyseal joints between fixed-head screws showed bony union, the amount of callus in the zygapophyseal joints connected with mobile-head screws was small, and joint space was confirmed by CT. No metalloses were noted around any of the screws. Novel screws were suggested to be highly durable and histologically safe.

Charging of mobile services by mobile payment reference model

OpenAIRE

Pousttchi, Key; Wiedemann, Dietmar Georg

2005-01-01

The purpose of the paper is to analyze mobile payments in the mobile commerce scenario. Therefore, we first classify the mobile payment in the mobile commerce scenario by explaining general offer models, charging concepts, and intermediaries. Second, we describe the mobile payment reference model, especially, the mobile payment reference organization model and different mobile payment standard types. Finally, we conclude our findings.

Mobilities

DEFF Research Database (Denmark)

to social networks, personal identities, and our relationship to the built environment. The omnipresence of mobilities within everyday life, high politics, technology, and tourism (to mention but a few) all point to a key insight harnessed by the ‘mobilities turn’. Namely that mobilities is much more than......The world is on the move. This is a widespread understanding by many inhabitants of contemporary society across the Globe. But what does it actually mean? During over one decade the ‘mobilities turn’ within the social sciences have provided a new set of insights into the repercussions of mobilities...... and environmental degradation. The spaces and territories marked by mobilities as well as the sites marked by the bypassing of such are explored. Moreover, the architectural and technological dimensions to infrastructures and sites of mobilities will be included as well as the issues of power, social exclusion...

Measurement needs guided by synthetic radar scans in high-resolution model output

Science.gov (United States)

Varble, A.; Nesbitt, S. W.; Borque, P.

2017-12-01

Microphysical and dynamical process interactions within deep convective clouds are not well understood, partly because measurement strategies often focus on statistics of cloud state rather than cloud processes. While processes cannot be directly measured, they can be inferred with sufficiently frequent and detailed scanning radar measurements focused on the life cycleof individual cloud regions. This is a primary goal of the 2018-19 DOE ARM Cloud, Aerosol, and Complex Terrain Interactions (CACTI) and NSF Remote sensing of Electrification, Lightning, And Mesoscale/microscale Processes with Adaptive Ground Observations (RELAMPAGO) field campaigns in central Argentina, where orographic deep convective initiation is frequent with some high-impact systems growing into the tallest and largest in the world. An array of fixed and mobile scanning multi-wavelength dual-polarization radars will be coupled with surface observations, sounding systems, multi-wavelength vertical profilers, and aircraft in situ measurements to characterize convective cloud life cycles and their relationship with environmental conditions. While detailed cloud processes are an observational target, the radar scan patterns that are most ideal for observing them are unclear. They depend on the locations and scales of key microphysical and dynamical processes operating within the cloud. High-resolution simulations of clouds, while imperfect, can provide information on these locations and scales that guide radar measurement needs. Radar locations are set in the model domain based on planned experiment locations, and simulatedorographic deep convective initiation and upscale growth are sampled using a number of different scans involving RHIs or PPIs with predefined elevation and azimuthal angles that approximately conform with radar range and beam width specifications. Each full scan pattern is applied to output atsingle model time steps with time step intervals that depend on the length of time

Thermographic analysis of the effect of composite type, layering method, and curing light on the temperature rise of photo-cured composites in tooth cavities.

Science.gov (United States)

Kim, Min-Jung; Kim, Ryan Jin-Young; Ferracane, Jack; Lee, In-Bog

2017-10-01

The purpose of this study was to investigate temperature rise in the composite and dentin of a class I cavity in extracted human molars under different restoration conditions, including the use of different composite types, layering methods, and curing lights. Open occlusal cavities were prepared on 28 extracted human molars. A conventional (Filtek Z250) and a bulk-fill (Filtek Bulk Fill Posterior; BFP) composite were used to restore the preparations. BFP was incrementally layered or bulk-filled. Bulk-filled BFP was cured with two different lights, the Elipar S10 and the BeLite. Each layer was illuminated for 20s, while thermograms of the specimens were recorded for 100s using an infrared thermal camera. Temperature changes on the composite and dentin surfaces were obtained at points of interest (POI) pertaining to successive incremental distances of 0.75mm from the top of the cavity to the pulp. The polymerization kinetics of each composite was determined using photo-differential scanning calorimetry. The greatest temperature rise was observed 0.75mm apical from the top of the cavity. All groups showed over 6°C maximum temperature rise (ΔT max ) at the pulpal side of the dentin. Upon curing, Z250 reached ΔT=5°C faster than BFP; however, ΔT max of the two composites were comparable at any POI. Bulk filling showed greater ΔT max than incremental filling at 0.75mm apical from the top and in the middle of the cavity. The Elipar S10 light generated faster temperature changes in the curing composite at all recorded positions throughout the depth of the cavity and greater ΔT max in all POIs compared to BeLite. Real-time thermographic analysis demonstrated that the composite type and layering method did not influence the temperature rise at the pulpal side of dentin during composite restoration of an occlusal preparation in a tooth. The amount and initial rate of temperature increase was most affected by the radiant exposure of the light curing unit. Within the

Client Mobile Software Design Principles for Mobile Learning Systems

Directory of Open Access Journals (Sweden)

Qing Tan

2009-01-01

Full Text Available In a client-server mobile learning system, client mobile software must run on the mobile phone to acquire, package, and send student’s interaction data via the mobile communications network to the connected mobile application server. The server will receive and process the client data in order to offer appropriate content and learning activities. To develop the mobile learning systems there are a number of very important issues that must be addressed. Mobile phones have scarce computing resources. They consist of heterogeneous devices and use various mobile operating systems, they have limitations with their user/device interaction capabilities, high data communications cost, and must provide for device mobility and portability. In this paper we propose five principles for designing Client mobile learning software. A location-based adaptive mobile learning system is presented as a proof of concept to demonstrate the applicability of these design principles.

Graphics hardware accelerated panorama builder for mobile phones

Science.gov (United States)

Bordallo López, Miguel; Hannuksela, Jari; Silvén, Olli; Vehviläinen, Markku

2009-02-01

Modern mobile communication devices frequently contain built-in cameras allowing users to capture highresolution still images, but at the same time the imaging applications are facing both usability and throughput bottlenecks. The difficulties in taking ad hoc pictures of printed paper documents with multi-megapixel cellular phone cameras on a common business use case, illustrate these problems for anyone. The result can be examined only after several seconds, and is often blurry, so a new picture is needed, although the view-finder image had looked good. The process can be a frustrating one with waits and the user not being able to predict the quality beforehand. The problems can be traced to the processor speed and camera resolution mismatch, and application interactivity demands. In this context we analyze building mosaic images of printed documents from frames selected from VGA resolution (640x480 pixel) video. High interactivity is achieved by providing real-time feedback on the quality, while simultaneously guiding the user actions. The graphics processing unit of the mobile device can be used to speed up the reconstruction computations. To demonstrate the viability of the concept, we present an interactive document scanning application implemented on a Nokia N95 mobile phone.

Thermographic imaging of superficial temperature in dogs sedated with medetomidine and butorphanol with and without MK-467 (L-659'066).

Science.gov (United States)

Vainionpää, Mari; Salla, Kati; Restitutti, Flávia; Raekallio, Marja; Junnila, Jouni; Snellman, Marjatta; Vainio, Outi

2013-03-01

To record, with a thermal camera, peripheral temperature changes during different sedation protocols and to relate the results to changes in the rectal temperature. Randomized crossover part-blinded experimental study. Eight healthy purpose-bred neutered Beagles (two females and six males) weight 14.5 ± 1.6 kg (mean ± SD) and aged 3-4 years. Each dog was sedated four times. Treatments were medetomidine 20 μg kg(-1) and butorphanol 0.1 mg kg(-1) (MB) with or without MK-467 500 μg kg(-1) (MK). Both drug combinations were administered IV and IM as separate treatments. A thermal camera (T425, FLIR) with a resolution of 320 by 240 was used for imaging. The dogs were placed in lateral recumbency on an insulated mattress. Digital (DFT) and metatarsal footpad temperatures (MFT) were measured with thermography. Thermograms and rectal temperature (RT) were taken before and at 3, 10, 20, 30, 45 and 60 minutes after treatment. At 60 minutes after drug administration, MFT was higher (p temperature changes can be seen and detected with thermography. MK-467 used with MB resulted in increased superficial temperatures and a decline in rectal temperature compared to MB alone. The sedation protocol may influence core temperature loss, and may also have an effect on thermographic images. © 2012 The Authors. Veterinary Anaesthesia and Analgesia. © 2012 Association of Veterinary Anaesthetists and the American College of Veterinary Anesthesiologists.

Mobile Multicast in Hierarchical Proxy Mobile IPV6

Science.gov (United States)

Hafizah Mohd Aman, Azana; Hashim, Aisha Hassan A.; Mustafa, Amin; Abdullah, Khaizuran

2013-12-01

Mobile Internet Protocol Version 6 (MIPv6) environments have been developing very rapidly. Many challenges arise with the fast progress of MIPv6 technologies and its environment. Therefore the importance of improving the existing architecture and operations increases. One of the many challenges which need to be addressed is the need for performance improvement to support mobile multicast. Numerous approaches have been proposed to improve mobile multicast performance. This includes Context Transfer Protocol (CXTP), Hierarchical Mobile IPv6 (HMIPv6), Fast Mobile IPv6 (FMIPv6) and Proxy Mobile IPv6 (PMIPv6). This document describes multicast context transfer in hierarchical proxy mobile IPv6 (H-PMIPv6) to provide better multicasting performance in PMIPv6 domain.

Head CT scan

Science.gov (United States)

... scan - orbits; CT scan - sinuses; Computed tomography - cranial; CAT scan - brain ... head size in children Changes in thinking or behavior Fainting Headache, when you have certain other signs ...

Heart PET scan

Science.gov (United States)

... nuclear medicine scan; Heart positron emission tomography; Myocardial PET scan ... A PET scan requires a small amount of radioactive material (tracer). This tracer is given through a vein (IV), ...

Application of structured illumination to gas phase thermometry using thermographic phosphor particles: a study for averaged imaging

Science.gov (United States)

Zentgraf, Florian; Stephan, Michael; Berrocal, Edouard; Albert, Barbara; Böhm, Benjamin; Dreizler, Andreas

2017-07-01

Structured laser illumination planar imaging (SLIPI) is combined with gas phase thermometry measurements using thermographic phosphor (TGP) particles. The technique is applied to a heated jet surrounded by a coflow which is operated at ambient temperature. The respective air flows are seeded with a powder of BaMgAl10O17:Eu2+ (BAM) which is used as temperature-sensitive gas phase tracer. Upon pulsed excitation in the ultraviolet spectral range, the temperature is extracted based on the two-color ratio method combined with SLIPI. The main advantage of applying the SLIPI approach to phosphor thermometry is the reduction of particle-to-particle multiple light scattering and diffuse wall reflections, yielding a more robust calibration procedure as well as improving the measurement accuracy, precision, and sensitivity. For demonstration, this paper focuses on sample-averaged measurements of temperature fields in a jet-in-coflow configuration. Using the conventional approach, which in contrast to SLIPI is based on imaging with an unmodulated laser light sheet, we show that for the present setup typically 40% of the recorded signal is affected by the contribution of multiply scattered photons. At locations close to walls even up to 75% of the apparent signal is due to diffuse reflection and wall luminescence of BAM sticking at the surface. Those contributions lead to erroneous temperature fields. Using SLIPI, an unbiased two-color ratio field is recovered allowing for two-dimensional mean temperature reconstructions which exhibit a more realistic physical behavior. This is in contrast to results deduced by the conventional approach. Furthermore, using the SLIPI approach it is shown that the temperature sensitivity is enhanced by a factor of up to 2 at 270 °C. Finally, an outlook towards instantaneous SLIPI phosphorescence thermometry is provided.

Mobilities Design

DEFF Research Database (Denmark)

Lanng, Ditte Bendix; Wind, Simon; Jensen, Ole B.

2017-01-01

Mobilities comprise a large part of our world and everyday lives, and the mobilities spaces in which we travel are ubiquitous. Yet, ordinary mobilities spaces – such as parking lots, pedestrian tunnels, and road lay-bys – tend to be criticized as typologies that lack consideration for the people...... who use them and for their wider social, aesthetic, cultural, and ecological agency in the city. This is clearly not an unambiguous characterization. But from it follows an urgency to re-examine unheeded mobilities spaces and extend demands of their agency beyond standards of technical efficiency....... This article draws on the recent “mobilities turn” in social science to support such re-examination of mobilities spaces. In social-scientific mobilities research, mobilities are considered the departure point for understanding the socio-material world in which we live. Mobilities are regarded as far more than...

Bone scan and joint scan of hands and feet in rheumatoid arthritis

International Nuclear Information System (INIS)

Carpentier, N.; Verbeke, S.; Perdrisot, R.; Grilo, R.M.; Quenesson, E.; Bonnet, C.; Vergne, P.; Treves, R.; Bertin, P.; Boutros-Toni, F.

2000-01-01

The aim of this study was to determine the ability of joint scan and bone scan of hands and feet, in patients with rheumatoid arthritis, to localize the altered joints. The sensitivity, the specificity, the positive predictive value (PPV) and the negative predictive value (NPV) of joint scan were determined in comparison with clinical joint assessment. Fifteen patients (780 joints) were clinically examined (pain and synovitis); during the same day, a bone scan and a joint scan were realized by oxidronate 99m Tc intravenous injection. Patients were scanned 5 minutes (tissual time, T t ) and 3 hours 1/4 (bone time, T 0 ) after the administration. The uptake of the bi-phosphonate was evaluated with a qualitative method using a grey scale. The uptake of 99m Tc oxidronate was quantitated using an extra-articular region of interest. The sensitivity, specificity, PPV and NPV of the scan at Tt were 46%, 96%, 85% et 78%. The same parameters were 75%, 66%, 53% and 84% for the scan realized at T 0 . The joint scan has showed 22% of false positive. These false positives could be a consequence of an earlier detection of joint alterations by scan. The joint scan should forecast the evolution of joints in patients with rheumatoid arthritis. (author)

Scanning gamma camera

International Nuclear Information System (INIS)

Engdahl, L.W.; Batter, J.F. Jr.; Stout, K.J.

1977-01-01

A scanning system for a gamma camera providing for the overlapping of adjacent scan paths is described. A collimator mask having tapered edges provides for a graduated reduction in intensity of radiation received by a detector thereof, the reduction in intensity being graduated in a direction normal to the scanning path to provide a blending of images of adjacent scan paths. 31 claims, 15 figures

Efficient Mobility Management Signalling in Network Mobility Supported PMIPV6.

Science.gov (United States)

Samuelraj, Ananthi Jebaseeli; Jayapal, Sundararajan

2015-01-01

Proxy Mobile IPV6 (PMIPV6) is a network based mobility management protocol which supports node's mobility without the contribution from the respective mobile node. PMIPV6 is initially designed to support individual node mobility and it should be enhanced to support mobile network movement. NEMO-BSP is an existing protocol to support network mobility (NEMO) in PMIPV6 network. Due to the underlying differences in basic protocols, NEMO-BSP cannot be directly applied to PMIPV6 network. Mobility management signaling and data structures used for individual node's mobility should be modified to support group nodes' mobility management efficiently. Though a lot of research work is in progress to implement mobile network movement in PMIPV6, it is not yet standardized and each suffers with different shortcomings. This research work proposes modifications in NEMO-BSP and PMIPV6 to achieve NEMO support in PMIPV6. It mainly concentrates on optimizing the number and size of mobility signaling exchanged while mobile network or mobile network node changes its access point.

Efficient Mobility Management Signalling in Network Mobility Supported PMIPV6

Directory of Open Access Journals (Sweden)

Ananthi Jebaseeli Samuelraj

2015-01-01

Full Text Available Proxy Mobile IPV6 (PMIPV6 is a network based mobility management protocol which supports node’s mobility without the contribution from the respective mobile node. PMIPV6 is initially designed to support individual node mobility and it should be enhanced to support mobile network movement. NEMO-BSP is an existing protocol to support network mobility (NEMO in PMIPV6 network. Due to the underlying differences in basic protocols, NEMO-BSP cannot be directly applied to PMIPV6 network. Mobility management signaling and data structures used for individual node’s mobility should be modified to support group nodes’ mobility management efficiently. Though a lot of research work is in progress to implement mobile network movement in PMIPV6, it is not yet standardized and each suffers with different shortcomings. This research work proposes modifications in NEMO-BSP and PMIPV6 to achieve NEMO support in PMIPV6. It mainly concentrates on optimizing the number and size of mobility signaling exchanged while mobile network or mobile network node changes its access point.

Wafer-level vacuum packaged resonant micro-scanning mirrors for compact laser projection displays

Science.gov (United States)

Hofmann, Ulrich; Oldsen, Marten; Quenzer, Hans-Joachim; Janes, Joachim; Heller, Martin; Weiss, Manfred; Fakas, Georgios; Ratzmann, Lars; Marchetti, Eleonora; D'Ascoli, Francesco; Melani, Massimiliano; Bacciarelli, Luca; Volpi, Emilio; Battini, Francesco; Mostardini, Luca; Sechi, Francesco; De Marinis, Marco; Wagner, Bernd

2008-02-01

Scanning laser projection using resonant actuated MEMS scanning mirrors is expected to overcome the current limitation of small display size of mobile devices like cell phones, digital cameras and PDAs. Recent progress in the development of compact modulated RGB laser sources enables to set up very small laser projection systems that become attractive not only for consumer products but also for automotive applications like head-up and dash-board displays. Within the last years continuous progress was made in increasing MEMS scanner performance. However, only little is reported on how mass-produceability of these devices and stable functionality even under harsh environmental conditions can be guaranteed. Automotive application requires stable MEMS scanner operation over a wide temperature range from -40° to +85°Celsius. Therefore, hermetic packaging of electrostatically actuated MEMS scanning mirrors becomes essential to protect the sensitive device against particle contamination and condensing moisture. This paper reports on design, fabrication and test of a resonant actuated two-dimensional micro scanning mirror that is hermetically sealed on wafer level. With resonant frequencies of 30kHz and 1kHz, an achievable Theta-D-product of 13mm.deg and low dynamic deformation <20nm RMS it targets Lissajous projection with SVGA-resolution. Inevitable reflexes at the vacuum package surface can be seperated from the projection field by permanent inclination of the micromirror.

Mobile CT. Technical aspects of prehospital stroke imaging before intravenous thrombolysis

International Nuclear Information System (INIS)

Gierhake, Daniel; Villringer, K.; Fiebach, J.B.; Weber, J.E.; Audebert, H.J.; Charite - Universitaetsmedizin Berlin; Ebinger, M.; Charite - Universitaetsmedizin Berlin

2013-01-01

To reduce the time from symptom onset to treatment with tissue plasminogen activator (tPA) in ischemic stroke, an ambulance was equipped with a CT scanner. We analyzed process and image quality of CT scanning during the pilot study regarding image quality and safety issues. The pilot study of a stroke emergency mobile unit (STEMO) ran over a period of 12 weeks on 5 weekdays from 7a. m. to 6:30 p. m. A teleradiological service for the justifying indication and reporting was established. The radiographer was responsible for the performance of the CT scan on the ambulance. 64 cranial CT scans and 1 intracranial CT angiography were performed. We compared times from ambulance alarm to treatment decision (time of last brain scan) with a cohort of 50 consecutive tPA treatments before implementation of STEMO. 62 (95 %) of the 65 scans performed had sufficient quality for reading. Technical quality was not optimal in 45 cases (69 %) mainly caused by suboptimal positioning of patient or eye lense protection. Motion artefacts were observed in 8 exams (12 %). No safety issues occurred for team or patients. 23 patients were treated with thrombolysis. Time from alarm to last CT scan was 18 minutes shorter than in the tPA cohort before STEMO implementation. A teleradiological support for primary stroke imaging by CT on-site is feasible, quality-wise of diagnostic value and has not raised safety issues. (orig.)

Investigation in uro-nephrology (1): diuretic renal scan in children

International Nuclear Information System (INIS)

Archambaud, F.; Olivier, P.; Guillet, J.; Wioland, M.; Bonnin, F.

2002-01-01

We present the results of a national investigation about the daily practice of diuretic renal scan in children and we compare these results to available international recommendations. Several questions were related to patient preparation, radiopharmaceutical injected activity, image acquisition, diuretic procedure, data processing and renal function quantification, and lastly hard copy output procedure. Diuretic renography is widely performed in children and national daily practice is in agreement with international recommendations about many aspects. However, some aspects should be improved such as hydration, standardisation of furosemide doses and post mobilization and post micturition images acquisition taking on account the effects of gravity and full bladder. Furthermore, a controversy does exist about interpretation of an impaired drainage. (authors)

Scanning tunneling microscopy II further applications and related scanning techniques

CERN Document Server

Güntherodt, Hans-Joachim

1992-01-01

Scanning Tunneling Microscopy II, like its predecessor, presents detailed and comprehensive accounts of the basic principles and broad range of applications of STM and related scanning probe techniques. The applications discussed in this volume come predominantly from the fields of electrochemistry and biology. In contrast to those described in Vol. I, these sudies may be performed in air and in liquids. The extensions of the basic technique to map other interactions are described inchapters on scanning force microscopy, magnetic force microscopy, scanning near-field optical microscopy, together with a survey of other related techniques. Also described here is the use of a scanning proximal probe for surface modification. Togehter, the two volumes give a comprehensive account of experimental aspcets of STM. They provide essentialreading and reference material for all students and researchers involvedin this field.

Indoor and Outdoor Mobile Mapping Systems for Architectural Surveys

Science.gov (United States)

Campi, M.; di Luggo, A.; Monaco, S.; Siconolfi, M.; Palomba, D.

2018-05-01

This paper presents the results of architectural surveys carried out with mobile mapping systems. The data acquired through different instruments for both indoor and outdoor surveying are analyzed and compared. The study sample shows what is required for an acquisition in a dynamic mode indicating the criteria for the creation of a georeferenced network for indoor spaces, as well as the operational processes concerning data capture, processing, and management. The differences between a dynamic and static scan have been evaluated, with a comparison being made with the aerial photogrammetric survey of the same sample.

CT Scan

Science.gov (United States)

... disease, lung nodules and liver masses Monitor the effectiveness of certain treatments, such as cancer treatment Detect ... scan done in a hospital or an outpatient facility. CT scans are painless and, with newer machines, ...

Renal scan

Science.gov (United States)

... this page: //medlineplus.gov/ency/article/003790.htm Renal scan To use the sharing features on this ... anaphylaxis . Alternative Names Renogram; Kidney scan Images Kidney anatomy Kidney - blood and urine flow References Chernecky CC, ...

Precursor and Neutral Loss Scans in an RF Scanning Linear Quadrupole Ion Trap

Science.gov (United States)

Snyder, Dalton T.; Szalwinski, Lucas J.; Schrader, Robert L.; Pirro, Valentina; Hilger, Ryan; Cooks, R. Graham

2018-03-01

Methodology for performing precursor and neutral loss scans in an RF scanning linear quadrupole ion trap is described and compared to the unconventional ac frequency scan technique. In the RF scanning variant, precursor ions are mass selectively excited by a fixed frequency resonance excitation signal at low Mathieu q while the RF amplitude is ramped linearly to pass ions through the point of excitation such that the excited ion's m/z varies linearly with time. Ironically, a nonlinear ac frequency scan is still required for ejection of the product ions since their frequencies vary nonlinearly with the linearly varying RF amplitude. In the case of the precursor scan, the ejection frequency must be scanned so that it is fixed on a product ion m/z throughout the RF scan, whereas in the neutral loss scan, it must be scanned to maintain a constant mass offset from the excited precursor ions. Both simultaneous and sequential permutation scans are possible; only the former are demonstrated here. The scans described are performed on a variety of samples using different ionization sources: protonated amphetamine ions generated by nanoelectrospray ionization (nESI), explosives ionized by low-temperature plasma (LTP), and chemical warfare agent simulants sampled from a surface and analyzed with swab touch spray (TS). We lastly conclude that the ac frequency scan variant of these MS/MS scans is preferred due to electronic simplicity. In an accompanying manuscript, we thus describe the implementation of orthogonal double resonance precursor and neutral loss scans on the Mini 12 using constant RF voltage. [Figure not available: see fulltext.

Mobile Phone Penetration, Mobile Banking and Inclusive Development in Africa

OpenAIRE

Asongu, Simplice; Nwachukwu, Jacinta C.

2016-01-01

The study assesses the role of mobile phones and mobile banking in decreasing inequality in 52 African countries. The empirical procedure involves first, examining the income-redistributive effect of mobile phone penetration and then investigating the contribution of mobile banking services in this relationship. The findings suggest an equalizing income-redistributive effect of ‘mobile phone penetration’ and ‘mobile banking’, with a higher income-equalizing effect from mobile banking compared...

Precision controlled atomic resolution scanning transmission electron microscopy using spiral scan pathways

Science.gov (United States)

Sang, Xiahan; Lupini, Andrew R.; Ding, Jilai; Kalinin, Sergei V.; Jesse, Stephen; Unocic, Raymond R.

2017-03-01

Atomic-resolution imaging in an aberration-corrected scanning transmission electron microscope (STEM) can enable direct correlation between atomic structure and materials functionality. The fast and precise control of the STEM probe is, however, challenging because the true beam location deviates from the assigned location depending on the properties of the deflectors. To reduce these deviations, i.e. image distortions, we use spiral scanning paths, allowing precise control of a sub-Å sized electron probe within an aberration-corrected STEM. Although spiral scanning avoids the sudden changes in the beam location (fly-back distortion) present in conventional raster scans, it is not distortion-free. “Archimedean” spirals, with a constant angular frequency within each scan, are used to determine the characteristic response at different frequencies. We then show that such characteristic functions can be used to correct image distortions present in more complicated constant linear velocity spirals, where the frequency varies within each scan. Through the combined application of constant linear velocity scanning and beam path corrections, spiral scan images are shown to exhibit less scan distortion than conventional raster scan images. The methodology presented here will be useful for in situ STEM imaging at higher temporal resolution and for imaging beam sensitive materials.

Mobility Divides

DEFF Research Database (Denmark)

Jensen, Ole B.

Contemporary mobilities are cultural and social manifestations, and the mobile practices in the everyday life of billions of humans are re-configuring senses of place, self, other and relationships to the built environment. The way ‘mobile situations’ are staged in designed and built environments......’ in the everyday life and cast light on how design and ‘materialities of mobilites’ are creating differential mobilities across societies, social networks, and communities of practices.......Contemporary mobilities are cultural and social manifestations, and the mobile practices in the everyday life of billions of humans are re-configuring senses of place, self, other and relationships to the built environment. The way ‘mobile situations’ are staged in designed and built environments...

Micro Mobility Marketing

DEFF Research Database (Denmark)

Hosbond, Jens Henrik; Skov, Mikael B.

2008-01-01

, in our case a medium-sized retail supermarket. Two prototypes based on push and pull marketing strategies are implemented and evaluated. Taking outset in a synthesis of central issues in contemporary research on mobile marketing, we discuss their role in micro mobility marketing to point to similarities......Mobile marketing refers to marketing of services or goods using mobile technology and mobile marketing holds potentially great economical opportunities. Traditionally, mobile marketing has been viewed as mobility in the large taking place virtually anywhere, anytime. Further, research shows...... considerable number of studies on push-based SMS mobile marketing campaigns. This paper explores a related yet different form of mobile marketing namely micro mobility marketing. Micro mobility marketing denotes mobility in the small, meaning that promotion of goods takes place within a circumscribed location...

Enhancement of carrier mobility in all-inkjet-printed organic thin-film transistors using a blend of poly(3-hexylthiophene) and carbon nanoparticles

International Nuclear Information System (INIS)

Lin, Chih-Ting; Hsu, Chun-Hao; Chen, Iu-Ren; Lee, Chang-Hung; Wu, Wen-Jung

2011-01-01

To enhance the carrier mobility of all-inkjet-printed organic thin film transistors, we fabricated devices that incorporated poly(3-hexylthiophene) (P3HT) and carbon nanoparticles (CNPs). The fabricated devices had an on/off ratio of 10 4 , which is one order less than that of pristine organic thin-film transistors (OTFTs). The maximum carrier mobility as high as 0.053 cm 2 /V-s was achieved for a CNP/P3HT weight-weight ratio of 7/100. This degree of mobility is 10 times greater than average mobility of pristine P3HT-OTFTs. X-ray diffraction and scanning electron microscopy images reveal that the carrier mobility was enhanced by reducing the injection barrier and enhancing the carrier injection. This work demonstrates the feasibility of all-inkjet-printed OTFT technology.

Mobile CT system for in-situ inspection of the LHC at CERN

International Nuclear Information System (INIS)

Sauerwein, Christoph; Haemmerle, Volker; Tiseanu, Ion; Williams, Lloyd R.; Caspers, Fritz

2010-01-01

The world's biggest particle accelerator, the Large Hadron Collider (LHC) was recently commissioned at CERN. It was found that a condition monitoring system for its connecting elements would be useful. A monitoring system of this kind must be able to function without opening connecting elements, without breaking the vacuum, and without heating up the inspection sector as this would be too costly and time-consuming. Further, the system should be mobile in order to be applicable in all positions of the 27 km long accelerator. A radiographic system will be used, with the intention to get an identifiable image of all structures in the connecting elements of the accelerator. The minimum requirement is an image that enables an assessment of the structural integrity and correct position of all important components. 3D CT is the ideal solution, but owing to the limited space it is impossible to move an X-ray tube and detector completely around the connecting elements. A mobile 3D CT unit was therefore developed which enables maximum scanning variety within the given limits and provides 3D images based on a strongly limited range of scanning angles. The system is described in the paper, along with the results achieved so far and with an outlook onto further applications. (orig.)

Mobilities Design

DEFF Research Database (Denmark)

Jensen, Ole B.; Lanng, Ditte Bendix

Contemporary society is marked and defined by the ways in which mobile goods, bodies, vehicles, objects, and data are organized, moved and staged. On the background of the ‘mobilities turn’ (e.g. Cresswell 2006, Urry 2007) this book articulates a new and emerging research field, namely that of ‘m......Contemporary society is marked and defined by the ways in which mobile goods, bodies, vehicles, objects, and data are organized, moved and staged. On the background of the ‘mobilities turn’ (e.g. Cresswell 2006, Urry 2007) this book articulates a new and emerging research field, namely...... that of ‘mobilities design’. The book revolves around the following research question: How are design decisions and interventions staging mobilities? It builds upon the Staging Mobilities model (Jensen 2013) in an explorative inquiry into the problems and potentials of the design of mobilities. The exchange value...

Advances in 4D treatment planning for scanned particle beam therapy - report of dedicated workshops.

Science.gov (United States)

Bert, Christoph; Graeff, Christian; Riboldi, Marco; Nill, Simeon; Baroni, Guido; Knopf, Antje-Christin

2014-12-01

We report on recent progress in the field of mobile tumor treatment with scanned particle beams, as discussed in the latest editions of the 4D treatment planning workshop. The workshop series started in 2009, with about 20 people from 4 research institutes involved, all actively working on particle therapy delivery and development. The first workshop resulted in a summary of recommendations for the treatment of mobile targets, along with a list of requirements to apply these guidelines clinically. The increased interest in the treatment of mobile tumors led to a continuously growing number of attendees: the 2012 edition counted more than 60 participants from 20 institutions and commercial vendors. The focus of research discussions among workshop participants progressively moved from 4D treatment planning to complete 4D treatments, aiming at effective and safe treatment delivery. Current research perspectives on 4D treatments include all critical aspects of time resolved delivery, such as in-room imaging, motion detection, beam application, and quality assurance techniques. This was motivated by the start of first clinical treatments of hepato cellular tumors with a scanned particle beam, relying on gating or abdominal compression for motion mitigation. Up to date research activities emphasize significant efforts in investigating advanced motion mitigation techniques, with a specific interest in the development of dedicated tools for experimental validation. Potential improvements will be made possible in the near future through 4D optimized treatment plans that require upgrades of the currently established therapy control systems for time resolved delivery. But since also these novel optimization techniques rely on the validity of the 4DCT, research focusing on alternative 4D imaging technique, such as MRI based 4DCT generation will continue.

Mobile Election

OpenAIRE

Long, Elena; Lovitskii, Vladimir; Thrasher, Michael; Traynor, David

2009-01-01

Mobile phones have the potential of fostering political mobilisation. There is a significant political power in mobile technology. Like the Internet, mobile phones facilitate communication and rapid access to information. Compared to the Internet, however, mobile phone diffusion has reached a larger proportion of the population in most countries, and thus the impact of this new medium is conceivably greater. There are now more mobile phones in the UK than there are people (ave...

Development of a simple gamma ray source seeking mobile platform

Energy Technology Data Exchange (ETDEWEB)

Miller, A.; Machrafi, R.; Mohany, A., E-mail: alexander.miller@uoit.ca [Univ. of Ontario Inst. of Tech., Oshawa, ON (Canada)

2014-07-01

This paper presents a novel method for a small, inexpensive mobile robot equipped with a lanthanum bromide detector to survey a local area and identify sources of gamma radiation. This is achieved by surrounding the lanthanum bromide detector with a lead sheath that blocks all gamma rays except those incident along the detector's axial direction. A 360{sup o} horizontal scan is performed by rotating both the robot and the lanthanum bromide detector and a directional profile of gamma radiation is constructed. (author)

Telemedicine Based on Mobile Devices and Mobile Cloud Computing

OpenAIRE

Lidong Wang; Cheryl Ann Alexander

2014-01-01

Mobile devices such as smartphones and tablets support kinds of mobile computing and services. They can access to the cloud or offload the computation-intensive part to the cloud computing resources. Mobile cloud computing (MCC) integrates the cloud computing into the mobile environment, which extends mobile devices’ battery lifetime, improves their data storage capacity and processing power, and improves their reliability and information security. In this paper, the applications of smartphon...

Mobile In Vivo Infrared Data Collection and Diagnoses Comparison System

Science.gov (United States)

Mintz, Frederick W. (Inventor); Moynihan, Philip I. (Inventor); Gunapala, Sarath D. (Inventor)

2013-01-01

Described is a mobile in vivo infrared brain scan and analysis system. The system includes a data collection subsystem and a data analysis subsystem. The data collection subsystem is a helmet with a plurality of infrared (IR) thermometer probes. Each of the IR thermometer probes includes an IR photodetector capable of detecting IR radiation generated by evoked potentials within a user's skull. The helmet is formed to collect brain data that is reflective of firing neurons in a mobile subject and transmit the brain data to the data analysis subsystem. The data analysis subsystem is configured to generate and display a three-dimensional image that depicts a location of the firing neurons. The data analysis subsystem is also configured to compare the brain data against a library of brain data to detect an anomaly in the brain data, and notify a user of any detected anomaly in the brain data.

Postprocessing Algorithm for Driving Conventional Scanning Tunneling Microscope at Fast Scan Rates.

Science.gov (United States)

Zhang, Hao; Li, Xianqi; Chen, Yunmei; Park, Jewook; Li, An-Ping; Zhang, X-G

2017-01-01

We present an image postprocessing framework for Scanning Tunneling Microscope (STM) to reduce the strong spurious oscillations and scan line noise at fast scan rates and preserve the features, allowing an order of magnitude increase in the scan rate without upgrading the hardware. The proposed method consists of two steps for large scale images and four steps for atomic scale images. For large scale images, we first apply for each line an image registration method to align the forward and backward scans of the same line. In the second step we apply a "rubber band" model which is solved by a novel Constrained Adaptive and Iterative Filtering Algorithm (CIAFA). The numerical results on measurement from copper(111) surface indicate the processed images are comparable in accuracy to data obtained with a slow scan rate, but are free of the scan drift error commonly seen in slow scan data. For atomic scale images, an additional first step to remove line-by-line strong background fluctuations and a fourth step of replacing the postprocessed image by its ranking map as the final atomic resolution image are required. The resulting image restores the lattice image that is nearly undetectable in the original fast scan data.

Postprocessing Algorithm for Driving Conventional Scanning Tunneling Microscope at Fast Scan Rates

Directory of Open Access Journals (Sweden)

Hao Zhang

2017-01-01

Full Text Available We present an image postprocessing framework for Scanning Tunneling Microscope (STM to reduce the strong spurious oscillations and scan line noise at fast scan rates and preserve the features, allowing an order of magnitude increase in the scan rate without upgrading the hardware. The proposed method consists of two steps for large scale images and four steps for atomic scale images. For large scale images, we first apply for each line an image registration method to align the forward and backward scans of the same line. In the second step we apply a “rubber band” model which is solved by a novel Constrained Adaptive and Iterative Filtering Algorithm (CIAFA. The numerical results on measurement from copper(111 surface indicate the processed images are comparable in accuracy to data obtained with a slow scan rate, but are free of the scan drift error commonly seen in slow scan data. For atomic scale images, an additional first step to remove line-by-line strong background fluctuations and a fourth step of replacing the postprocessed image by its ranking map as the final atomic resolution image are required. The resulting image restores the lattice image that is nearly undetectable in the original fast scan data.

Mobile Advertising

OpenAIRE

Alamuri, Lavanya

2009-01-01

The aim of this project was to get an understanding of how companies adopt mobile as an advertising medium. The literature review aided in framing a draft of the factors that affect mobile advertising adoption and possible forms of mobile advertising. Considering the scope of the thesis work, branding strategy, service costs, personalization and privacy and platform were considered to be the factors that could affect the mobile advertising adoption. A few possible forms on mobile device we...

Mobile phones, social ties, and collective action mobilization in China

DEFF Research Database (Denmark)

Liu, Jun

2017-01-01

To provide a better understanding of mobile phones as a recruitment tool in collective actions, this study explores the use of mobile phones for mobilizing protest in China. Using in-depth interviews and investigating four cases in which Chinese people employed mobile devices to recruit...... participants for protests, this study observes that mobile communication in China embodies guanxi, the indigenous social tie in Chinese society that introduces reciprocity as an influential facilitator of collective actions. The embedment of reciprocity facilitates the proliferation of mobilizing calls......, legitimizes mobilizing appeals, generates obligations and consolidates solidarity for collective actions. The study concludes with a consideration of the relevance of mobile phones for the embedment of reciprocity in social ties in the mobilization of collective action in authoritarian regimes such as China....

Extrinsic Parameter Calibration for Line Scanning Cameras on Ground Vehicles with Navigation Systems Using a Calibration Pattern

Directory of Open Access Journals (Sweden)

Alexander Wendel

2017-10-01

Full Text Available Line scanning cameras, which capture only a single line of pixels, have been increasingly used in ground based mobile or robotic platforms. In applications where it is advantageous to directly georeference the camera data to world coordinates, an accurate estimate of the camera’s 6D pose is required. This paper focuses on the common case where a mobile platform is equipped with a rigidly mounted line scanning camera, whose pose is unknown, and a navigation system providing vehicle body pose estimates. We propose a novel method that estimates the camera’s pose relative to the navigation system. The approach involves imaging and manually labelling a calibration pattern with distinctly identifiable points, triangulating these points from camera and navigation system data and reprojecting them in order to compute a likelihood, which is maximised to estimate the 6D camera pose. Additionally, a Markov Chain Monte Carlo (MCMC algorithm is used to estimate the uncertainty of the offset. Tested on two different platforms, the method was able to estimate the pose to within 0.06 m/1.05 ∘ and 0.18 m/2.39 ∘ . We also propose several approaches to displaying and interpreting the 6D results in a human readable way.

The setup of a mobile mobility panel for the Netherlands

NARCIS (Netherlands)

Geurs, Karst Teunis; Veenstra, Sander; Thomas, Tom

2013-01-01

This paper describes the setup of the Dutch Mobile Mobility Panel project, in which GPS-enabled mobile phones (smartphones) are used as a passive multiple-week and multiple-year travel behaviour data collection tool. The data collection methodology used in the Dutch Mobile Mobility Panel comprised

LOSA-M3: multi-wave polarization scanning lidar for research of the troposphere and cirrus clouds

Science.gov (United States)

Kokhanenko, G. P.; Balin, Yu. S.; Klemasheva, M. G.; Penner, I. E.; Nasonov, S. V.; Samoilova, S. V.

2017-11-01

Lidar is designed to study the aerosol fields of the troposphere and the polarization characteristics of crystal clouds. Two laser wavelengths are used - 1064 and 532 nm, elastic scattering signals and spontaneous Raman scattering of nitrogen (607 nm) are recorded. Lidar is made in a mobile version, allowing its transportation by road and working under expeditionary conditions. The lidar transceiver is placed on a scanning column, which allows to change the direction of sounding within the upper hemisphere at a speed of 1 degree per second. The polarization characteristics of the transmitter and receiver can be changed by rotating the phase plates synchronously with the the laser pulses. In combination with conical scanning of the lidar, this makes it possible to detect the anisotropy of scattering and the possible azimuthal orientation of the crystal particles.

Scanning tunneling microscopy II further applications and related scanning techniques

CERN Document Server

Güntherodt, Hans-Joachim

1995-01-01

Scanning Tunneling Microscopy II, like its predecessor, presents detailed and comprehensive accounts of the basic principles and broad range of applications of STM and related scanning probe techniques. The applications discussed in this volume come predominantly from the fields of electrochemistry and biology. In contrast to those described in STM I, these studies may be performed in air and in liquids. The extensions of the basic technique to map other interactions are described in chapters on scanning force microscopy, magnetic force microscopy, and scanning near-field optical microscopy, together with a survey of other related techniques. Also described here is the use of a scanning proximal probe for surface modification. Together, the two volumes give a comprehensive account of experimental aspects of STM. They provide essential reading and reference material for all students and researchers involved in this field. In this second edition the text has been updated and new methods are discussed.

Mobile human-computer interaction perspective on mobile learning

CSIR Research Space (South Africa)

Botha, Adèle

2010-10-01

Full Text Available Applying a Mobile Human Computer Interaction (MHCI) view to the domain of education using Mobile Learning (Mlearning), the research outlines its understanding of the influences and effects of different interactions on the use of mobile technology...

WormScan: a technique for high-throughput phenotypic analysis of Caenorhabditis elegans.

Directory of Open Access Journals (Sweden)

Mark D Mathew

Full Text Available BACKGROUND: There are four main phenotypes that are assessed in whole organism studies of Caenorhabditis elegans; mortality, movement, fecundity and size. Procedures have been developed that focus on the digital analysis of some, but not all of these phenotypes and may be limited by expense and limited throughput. We have developed WormScan, an automated image acquisition system that allows quantitative analysis of each of these four phenotypes on standard NGM plates seeded with E. coli. This system is very easy to implement and has the capacity to be used in high-throughput analysis. METHODOLOGY/PRINCIPAL FINDINGS: Our system employs a readily available consumer grade flatbed scanner. The method uses light stimulus from the scanner rather than physical stimulus to induce movement. With two sequential scans it is possible to quantify the induced phototactic response. To demonstrate the utility of the method, we measured the phenotypic response of C. elegans to phosphine gas exposure. We found that stimulation of movement by the light of the scanner was equivalent to physical stimulation for the determination of mortality. WormScan also provided a quantitative assessment of health for the survivors. Habituation from light stimulation of continuous scans was similar to habituation caused by physical stimulus. CONCLUSIONS/SIGNIFICANCE: There are existing systems for the automated phenotypic data collection of C. elegans. The specific advantages of our method over existing systems are high-throughput assessment of a greater range of phenotypic endpoints including determination of mortality and quantification of the mobility of survivors. Our system is also inexpensive and very easy to implement. Even though we have focused on demonstrating the usefulness of WormScan in toxicology, it can be used in a wide range of additional C. elegans studies including lifespan determination, development, pathology and behavior. Moreover, we have even adapted the

Cooperative scans

NARCIS (Netherlands)

M. Zukowski (Marcin); P.A. Boncz (Peter); M.L. Kersten (Martin)

2004-01-01

textabstractData mining, information retrieval and other application areas exhibit a query load with multiple concurrent queries touching a large fraction of a relation. This leads to individual query plans based on a table scan or large index scan. The implementation of this access path in most

On the extent of researcher mobility and indicators for mobility

Energy Technology Data Exchange (ETDEWEB)

Barriere, S.; Baard, P.; Karlsson, S.; Jacobsson, C.; Tumpane, J.

2016-07-01

Researchers' mobility is significant for the quality of research, although mobility does not necessarily have an intrinsic value. Sweden appears to have a lover degree of mobility when compared to a selection of successful research countries. The Swedish Research Council shall, according to the instruction from the government , promote researcher mobility. This study explores job-mobility within the Swedish academic system based on register studies and draw some conclusions on the degree of mobility in different different disciplines, differences between men and women as well as on the development of comprehensive and easy to follow indicators for mobility. The study intends to provide support for recommendations on researcher mobility within the Research Council's overarching goal to promote excellence in research. (Author)

Mobility Management Algorithms for the Client-Driven Mobility Frame System–Mobility from a Brand New Point of View

Directory of Open Access Journals (Sweden)

Péter Fülöp

2009-01-01

Full Text Available In this paper a new mobility management is introduced. The main idea in this approach is that the mobil node should manage the mobility for itself not the network. The network nodes provide only basic services for mobile entities: connectivity and administration. We construct a framework called the Client-based Mobility Frame System (CMFS for this mobility environment. We developed the CMFS protocol as a solution over IPv4 and we show how to use Mobile IPv6 to realize our concept. We propose some basic mobility management solutions that can be implemented into the mobile clients and give details about a working simulation of a complete Mobility Management System. Example mobility management approaches such as the centralized- and hierarchical- or cellular-like ones are also defined and hints are given what kind of algorithms might be implemented upon the Client-based Mobility Frame System over IPv4 and IPv6 as well. We introduce some example algorithms that can work with the CMFS making mobility management efficient by minimizing signalling load on the network. In the present work modeling and detailed discussion on the parameters of the algorithms is given and comparison to existing mobility approaches and protocols is done. We prepared a simulation to test our protocol and to back up the proposals we provide the reader with simulation results. We stress that still one the most important benefit of our findings is that all the MNs can run different management strategies and can optimize mobility for themselves.

Mobile Lexicography

DEFF Research Database (Denmark)

Køhler Simonsen, Henrik

2014-01-01

Users are already mobile, but the question is to which extent knowledge-based dictionary apps are designed for the mobile user situation. The objective of this article is to analyse the characteristics of the mobile user situation and to look further into the stationary user situation and the mob......Users are already mobile, but the question is to which extent knowledge-based dictionary apps are designed for the mobile user situation. The objective of this article is to analyse the characteristics of the mobile user situation and to look further into the stationary user situation...... and the mobile user situation. The analysis is based on an empirical survey involving ten medical doctors and a monolingual app designed to support cognitive lexicographic functions, cf. (Tarp 2006:61-64). In test A the doctors looked up five medical terms while sitting down at a desk and in test B the doctors...

A High Rigidity and Precision Scanning Tunneling Microscope with Decoupled XY and Z Scans.

Science.gov (United States)

Chen, Xu; Guo, Tengfei; Hou, Yubin; Zhang, Jing; Meng, Wenjie; Lu, Qingyou

2017-01-01

A new scan-head structure for the scanning tunneling microscope (STM) is proposed, featuring high scan precision and rigidity. The core structure consists of a piezoelectric tube scanner of quadrant type (for XY scans) coaxially housed in a piezoelectric tube with single inner and outer electrodes (for Z scan). They are fixed at one end (called common end). A hollow tantalum shaft is coaxially housed in the XY -scan tube and they are mutually fixed at both ends. When the XY scanner scans, its free end will bring the shaft to scan and the tip which is coaxially inserted in the shaft at the common end will scan a smaller area if the tip protrudes short enough from the common end. The decoupled XY and Z scans are desired for less image distortion and the mechanically reduced scan range has the superiority of reducing the impact of the background electronic noise on the scanner and enhancing the tip positioning precision. High quality atomic resolution images are also shown.

A High Rigidity and Precision Scanning Tunneling Microscope with Decoupled XY and Z Scans

Directory of Open Access Journals (Sweden)

Xu Chen

2017-01-01

Full Text Available A new scan-head structure for the scanning tunneling microscope (STM is proposed, featuring high scan precision and rigidity. The core structure consists of a piezoelectric tube scanner of quadrant type (for XY scans coaxially housed in a piezoelectric tube with single inner and outer electrodes (for Z scan. They are fixed at one end (called common end. A hollow tantalum shaft is coaxially housed in the XY-scan tube and they are mutually fixed at both ends. When the XY scanner scans, its free end will bring the shaft to scan and the tip which is coaxially inserted in the shaft at the common end will scan a smaller area if the tip protrudes short enough from the common end. The decoupled XY and Z scans are desired for less image distortion and the mechanically reduced scan range has the superiority of reducing the impact of the background electronic noise on the scanner and enhancing the tip positioning precision. High quality atomic resolution images are also shown.

Special raster scanning for reduction of charging effects in scanning electron microscopy.

Science.gov (United States)

Suzuki, Kazuhiko; Oho, Eisaku

2014-01-01

A special raster scanning (SRS) method for reduction of charging effects is developed for the field of SEM. Both a conventional fast scan (horizontal direction) and an unusual scan (vertical direction) are adopted for acquiring raw data consisting of many sub-images. These data are converted to a proper SEM image using digital image processing techniques. About sharpness of the image and reduction of charging effects, the SRS is compared with the conventional fast scan (with frame-averaging) and the conventional slow scan. Experimental results show the effectiveness of SRS images. By a successful combination of the proposed scanning method and low accelerating voltage (LV)-SEMs, it is expected that higher-quality SEM images can be more easily acquired by the considerable reduction of charging effects, while maintaining the resolution. © 2013 Wiley Periodicals, Inc.

Mobilities Mobilities

Directory of Open Access Journals (Sweden)

César Pompeyo

2011-12-01

Full Text Available Urry, John (2007 Mobilities.Oxford: Polity Press.Urry, John (2007 Mobilities.Oxford: Polity Press.John Urry (1946-, profesor en la Universidad de Lancaster, es un sociólogo de sobra conocido y altamente reputado en el panorama internacional de las ciencias sociales. Su dilatada carrera, aparentemente dispersa y diversificada, ha seguido senderos bastante bien definidos dejando tras de sí un catálogo extenso de obras sociológicas de primer nivel. Sus primeros trabajos se centraban en el campo de la teoría social y la filosofía de las ciencias sociales o de la sociología del poder [...

Scanning thermo-ionic microscopy for probing local electrochemistry at the nanoscale

Energy Technology Data Exchange (ETDEWEB)

Eshghinejad, Ahmadreza; Nasr Esfahani, Ehsan; Wang, Peiqi; Li, Jiangyu, E-mail: jjli@uw.edu [Department of Mechanical Engineering, University of Washington, Seattle, Washington 98195 (United States); Xie, Shuhong [Key Laboratory of Low Dimensional Materials and Application Technology of Ministry of Education, School of Materials Science and Engineering, Xiangtan University, Xiangtan 411105, Hunan (China); Shenzhen Key Laboratory of Nanobiomechanics, Shenzhen Institutes of Advanced Technology, Chinese Academy of Sciences, Shenzhen 518055, Guangdong (China); Geary, Timothy C.; Adler, Stuart B. [Department of Chemical Engineering, University of Washington, Seattle, Washington 98195 (United States)

2016-05-28

Conventional electrochemical characterization techniques based on voltage and current measurements only probe faradaic and capacitive rates in aggregate. In this work we develop a scanning thermo-ionic microscopy (STIM) to probe local electrochemistry at the nanoscale, based on imaging of Vegard strain induced by thermal oscillation. It is demonstrated from both theoretical analysis and experimental validation that the second harmonic response of thermally induced cantilever vibration, associated with thermal expansion, is present in all solids, whereas the fourth harmonic response, caused by local transport of mobile species, is only present in ionic materials. The origin of STIM response is further confirmed by its reduced amplitude with respect to increased contact force, due to the coupling of stress to concentration of ionic species and/or electronic defects. The technique has been applied to probe Sm-doped Ceria and LiFePO{sub 4}, both of which exhibit higher concentrations of mobile species near grain boundaries. The STIM gives us a powerful method to study local electrochemistry with high sensitivity and spatial resolution for a wide range of ionic systems, as well as ability to map local thermomechanical response.

Mobile Clouds

DEFF Research Database (Denmark)

Fitzek, Frank; Katz, Marcos

A mobile cloud is a cooperative arrangement of dynamically connected communication nodes sharing opportunistic resources. In this book, authors provide a comprehensive and motivating overview of this rapidly emerging technology. The book explores how distributed resources can be shared by mobile...... users in very different ways and for various purposes. The book provides many stimulating examples of resource-sharing applications. Enabling technologies for mobile clouds are also discussed, highlighting the key role of network coding. Mobile clouds have the potential to enhance communications...... performance, improve utilization of resources and create flexible platforms to share resources in very novel ways. Energy efficient aspects of mobile clouds are discussed in detail, showing how being cooperative can bring mobile users significant energy saving. The book presents and discusses multiple...

APPLICABILITY ANALYSIS OF CLOTH SIMULATION FILTERING ALGORITHM FOR MOBILE LIDAR POINT CLOUD

Directory of Open Access Journals (Sweden)

S. Cai

2018-04-01

Full Text Available Classifying the original point clouds into ground and non-ground points is a key step in LiDAR (light detection and ranging data post-processing. Cloth simulation filtering (CSF algorithm, which based on a physical process, has been validated to be an accurate, automatic and easy-to-use algorithm for airborne LiDAR point cloud. As a new technique of three-dimensional data collection, the mobile laser scanning (MLS has been gradually applied in various fields, such as reconstruction of digital terrain models (DTM, 3D building modeling and forest inventory and management. Compared with airborne LiDAR point cloud, there are some different features (such as point density feature, distribution feature and complexity feature for mobile LiDAR point cloud. Some filtering algorithms for airborne LiDAR data were directly used in mobile LiDAR point cloud, but it did not give satisfactory results. In this paper, we explore the ability of the CSF algorithm for mobile LiDAR point cloud. Three samples with different shape of the terrain are selected to test the performance of this algorithm, which respectively yields total errors of 0.44 %, 0.77 % and1.20 %. Additionally, large area dataset is also tested to further validate the effectiveness of this algorithm, and results show that it can quickly and accurately separate point clouds into ground and non-ground points. In summary, this algorithm is efficient and reliable for mobile LiDAR point cloud.

Mobile Traffic Alert and Tourist Route Guidance System Design Using Geospatial Data

Science.gov (United States)

Bhattacharya, D.; Painho, M.; Mishra, S.; Gupta, A.

2017-09-01

The present study describes an integrated system for traffic data collection and alert warning. Geographical information based decision making related to traffic destinations and routes is proposed through the design. The system includes a geospatial database having profile relating to a user of a mobile device. The processing and understanding of scanned maps, other digital data input leads to route guidance. The system includes a server configured to receive traffic information relating to a route and location information relating to the mobile device. Server is configured to send a traffic alert to the mobile device when the traffic information and the location information indicate that the mobile device is traveling toward traffic congestion. Proposed system has geospatial and mobile data sets pertaining to Bangalore city in India. It is envisaged to be helpful for touristic purposes as a route guidance and alert relaying information system to tourists for proximity to sites worth seeing in a city they have entered into. The system is modular in architecture and the novelty lies in integration of different modules carrying different technologies for a complete traffic information system. Generic information processing and delivery system has been tested to be functional and speedy under test geospatial domains. In a restricted prototype model with geo-referenced route data required information has been delivered correctly over sustained trials to designated cell numbers, with average time frame of 27.5 seconds, maximum 50 and minimum 5 seconds. Traffic geo-data set trials testing is underway.

A Planar Switchable 3-D-Coverage Phased Array Antenna and Its User Effects for 28-GHz Mobile Terminal Applications

DEFF Research Database (Denmark)

Zhang, Shuai; Chen, Xiaoming; Syrytsin, Igor A.

2017-01-01

This paper introduces a planar switchable 3D-coverage phased array for 28 GHz mobile terminal applications. In order to realize 3D-coverage beam scan with a simple planar array, chassis surface waves are efficiently excited and controlled by three identical slot subarrays. Three subarrays switch...

Scan path entropy and Arrow plots: Capturing scanning behavior of multiple observers

Directory of Open Access Journals (Sweden)

Ignace T C Hooge

2013-12-01

Full Text Available Designers of visual communication material want their material to attract and retain attention. In marketing research, heat maps, dwell time, and time to AOI first hit are often used as evaluation parameters. Here we present two additional measures 1 scan path entropy to quantify gaze guidance and 2 the arrow plot to visualize the average scan path. Both are based on string representations of scan paths. The latter also incorporates transition matrices and time required for 50% of the observers to first hit AOIs (T50. The new measures were tested in an eye tracking study (48 observers, 39 advertisements. Scan path entropy is a sensible measure for gaze guidance and the new visualization method reveals aspects of the average scan path and gives a better indication in what order global scanning takes place.

Cd Mobility in Anoxic Fe-Mineral-Rich Environments - Potential Use of Fe(III)-Reducing Bacteria in Soil Remediation

Science.gov (United States)

Muehe, E. M.; Adaktylou, I. J.; Obst, M.; Schröder, C.; Behrens, S.; Hitchcock, A. P.; Tylsizczak, T.; Michel, F. M.; Krämer, U.; Kappler, A.

2014-12-01

Agricultural soils are increasingly burdened with heavy metals such as Cd from industrial sources and impure fertilizers. Metal contaminants enter the food chain via plant uptake from soil and negatively affect human and environmental health. New remediation approaches are needed to lower soil metal contents. To apply these remediation techniques successfully, it is necessary to understand how soil microbes and minerals interact with toxic metals. Here we show that microbial Fe(III) reduction initially mobilizes Cd before its immobilization under anoxic conditions. To study how microbial Fe(III) reduction influences Cd mobility, we isolated a new Cd-tolerant, Fe(III)-reducing Geobacter sp. from a heavily Cd-contaminated soil. In lab experiments, this Geobacter strain first mobilized Cd from Cd-loaded Fe(III) hydroxides followed by precipitation of Cd-bearing mineral phases. Using Mössbauer spectroscopy and scanning electron microscopy, the original and newly formed Cd-containing Fe(II) and Fe(III) mineral phases, including Cd-Fe-carbonates, Fe-phosphates and Fe-(oxyhydr)oxides, were identified and characterized. Using energy-dispersive X-ray spectroscopy and synchrotron-based scanning transmission X-ray microscopy, Cd was mapped in the Fe(II) mineral aggregates formed during microbial Fe(III) reduction. Microbial Fe(III) reduction mobilizes Cd prior to its precipitation in Cd-bearing mineral phases. The mobilized Cd could be taken up by phytoremediating plants, resulting in a net removal of Cd from contaminated sites. Alternatively, Cd precipitation could reduce Cd bioavailability in the environment, causing less toxic effects to crops and soil microbiota. However, the stability and thus bioavailability of these newly formed Fe-Cd mineral phases needs to be assessed thoroughly. Whether phytoremediation or immobilization of Cd in a mineral with reduced Cd bioavailability are feasible mechanisms to reduce toxic effects of Cd in the environment remains to be

A Mobile IPv6 based Distributed Mobility Management Mechanism of Mobile Internet

Science.gov (United States)

Yan, Shi; Jiayin, Cheng; Shanzhi, Chen

A flatter architecture is one of the trends of mobile Internet. Traditional centralized mobility management mechanism faces the challenges such as scalability and UE reachability. A MIPv6 based distributed mobility management mechanism is proposed in this paper. Some important network entities and signaling procedures are defined. UE reachability is also considered in this paper through extension to DNS servers. Simulation results show that the proposed approach can overcome the scalability problem of the centralized scheme.

Mobile Semiotics

DEFF Research Database (Denmark)

Jensen, Ole B.

2013-01-01

This chapter aims to understand the mobile condition of contemporary life with a particular view to the signifying dimension of the environment and its ‘readability’. The chapter explores the potentials of semiotics and its relationship to the new mobilities literature. What takes place...... is a ‘mobile sense making’ where signs and materially situated meanings connect to the moving human body and thus create particular challenges and complexities of making sense of the world. The chapter includes notions of mobility systems and socio-technical networks in order to show how a ‘semiotic layer’ may...... work to afford or restrict mobile practices....

Scanning ARM Cloud Radars. Part II: Data Quality Control and Processing

Energy Technology Data Exchange (ETDEWEB)

Kollias, Pavlos; Jo, Ieng; Borque, Paloma; Tatarevic, Aleksandra; Lamer, Katia; Bharadwaj, Nitin; Widener, Kevin B.; Johnson, Karen L.; Clothiaux, Eugene E.

2014-03-01

The Scanning ARM Cloud Radars (SACR’s) are the primary instruments for documenting the four-dimensional structure and evolution of clouds within a 20-30 km radius from the ARM fixed and mobile sites. Here, the post-processing of the calibrated SACR measurements is discussed. First, a feature mask algorithm that objectively determines the presence of significant radar returns is described. The feature mask algorithm is based on the statistical properties of radar receiver noise. It accounts for atmospheric emission and is applicable even for SACR profiles with few or no signal-free range gates. Using the nearest-in-time atmospheric sounding, the SACR radar reflectivities are corrected for gaseous attenuation (water vapor and oxygen) using a line-by-line absorption model. Despite having a high pulse repetition frequency, the SACR has a narrow Nyquist velocity limit and thus Doppler velocity folding is commonly observed. An unfolding algorithm that makes use of a first guess for the true Doppler velocity using horizontal wind measurements from the nearest sounding is described. The retrieval of the horizontal wind profile from the HS-RHI SACR scan observations and/or nearest sounding is described. The retrieved horizontal wind profile can be used to adaptively configure SACR scan strategies that depend on wind direction. Several remaining challenges are discussed, including the removal of insect and second-trip echoes. The described algorithms significantly enhance SACR data quality and constitute an important step towards the utilization of SACR measurements for cloud research.

Modulation of Membrane Protein Lateral Mobility by Polyphosphates and Polyamines

Science.gov (United States)

Schindler, Melvin; Koppel, Dennis E.; Sheetz, Michael P.

1980-03-01

The lateral mobility of fluorescein-labeled membrane glycoproteins was measured in whole unlysed erythrocytes and erythrocyte ghosts by the technique of ``fluorescence redistribution after fusion.'' Measurements were made on polyethylene glycol-fused cell pairs in which only one member of the couplet was initially fluorescently labeled. Diffusion coefficients were estimated from the rate of fluorescence redistribution determined from successive scans with a focused laser beam across individual fused pairs. This technique allows for the analysis of diffusion within cell membranes without the possible damaging photochemical events caused by photobleaching. It was found that lateral mobility of erythrocyte proteins can be increased by the addition of polyphosphates (i.e., ATP and 2,3-diphosphoglycerate) and decreased by the addition of organic polyamines (i.e., neomycin and spermine). This control is exerted by these molecules only when they contact the cytoplasmic side of the membrane and is not dependent upon high-energy phosphates. Microviscosity experiments employing diphenylhexatriene demonstrated no changes in membrane lipid state as a function of these reagents. Our results, in conjunction with data on the physical interactions of cytoskeletal proteins, suggest that the diffusion effector molecules alter the lateral mobility of erythrocyte membrane proteins through modifications of interactions in the shell, which is composed of spectrin, actin, and component 4.1.

Mobilities Design

DEFF Research Database (Denmark)

Jensen, Ole B.; Lanng, Ditte Bendix; Wind, Simon

2016-01-01

In this paper, we identify the nexus between design (architecture, urban design, service design, etc.) and mobilities as a new and emerging research field. In this paper, we apply a “situational mobilities” perspective and take point of departure in the pragmatist question: “What design decisions...... and interventions affords this particular mobile situation?” The paper presents the contours of an emerging research agenda within mobilities research. The advent of “mobilities design” as an emerging research field points towards a critical interest in the material as well as practical consequences of contemporary......-making. The paper proposes that increased understanding of the material affordances facilitated through design provides important insight to planning and policymaking that at times might be in risk of becoming too detached from the everyday life of the mobile subject within contemporary mobilities landscapes....

Probabilistic Mobility Models for Mobile and Wireless Networks

DEFF Research Database (Denmark)

Song, Lei; Godskesen, Jens Christian

2010-01-01

In this paper we present a probabilistic broadcast calculus for mobile and wireless networks whose connections are unreliable. In our calculus broadcasted messages can be lost with a certain probability, and due to mobility the connection probabilities may change. If a network broadcasts a message...... from a location it will evolve to a network distribution depending on whether nodes at other locations receive the message or not. Mobility of locations is not arbitrary but guarded by a probabilistic mobility function (PMF) and we also define the notion of a weak bisimulation given a PMF...

Rapid-scan EPR imaging.

Science.gov (United States)

Eaton, Sandra S; Shi, Yilin; Woodcock, Lukas; Buchanan, Laura A; McPeak, Joseph; Quine, Richard W; Rinard, George A; Epel, Boris; Halpern, Howard J; Eaton, Gareth R

2017-07-01

In rapid-scan EPR the magnetic field or frequency is repeatedly scanned through the spectrum at rates that are much faster than in conventional continuous wave EPR. The signal is directly-detected with a mixer at the source frequency. Rapid-scan EPR is particularly advantageous when the scan rate through resonance is fast relative to electron spin relaxation rates. In such scans, there may be oscillations on the trailing edge of the spectrum. These oscillations can be removed by mathematical deconvolution to recover the slow-scan absorption spectrum. In cases of inhomogeneous broadening, the oscillations may interfere destructively to the extent that they are not visible. The deconvolution can be used even when it is not required, so spectra can be obtained in which some portions of the spectrum are in the rapid-scan regime and some are not. The technology developed for rapid-scan EPR can be applied generally so long as spectra are obtained in the linear response region. The detection of the full spectrum in each scan, the ability to use higher microwave power without saturation, and the noise filtering inherent in coherent averaging results in substantial improvement in signal-to-noise relative to conventional continuous wave spectroscopy, which is particularly advantageous for low-frequency EPR imaging. This overview describes the principles of rapid-scan EPR and the hardware used to generate the spectra. Examples are provided of its application to imaging of nitroxide radicals, diradicals, and spin-trapped radicals at a Larmor frequency of ca. 250MHz. Copyright © 2017 Elsevier Inc. All rights reserved.

Mobile marketing

OpenAIRE

KLEČKOVÁ, Zuzana

2013-01-01

The main aim of this thesis was to provide a comprehensive overview of the mobile marketing and analyze selected campaigns of Czech mobile marketing in comparison to world successful campaigns. The research contained studying of available literature about the theme to gain general knowledge about the issue. The theoretical part of the thesis contains predominantly various definitions of mobile marketing and its tools, advantages of these tools and some information about Mobile Marketing Assoc...

Mobile agents basic concepts, mobility models, and the tracy toolkit

CERN Document Server

Braun, Peter

2005-01-01

Mobile agents are software nomads that act as your personal representative, working autonomously through networks. They are able to visit network nodes directly using available computing power and are not limited by platform. This emerging field is now poised to become a cornerstone for new Web-based ubiquitous computing environments. Mobile Agents provides a practical introduction to mobile agent technology and surveys the state of the art in mobile agent research. Students and researchers can use the book as an introduction to the concepts and possibilities of this field and as an overview of ongoing research. Developers can use it to identify the capabilities of the technology to decide if mobile agents are the right solution for them. Practioners can also gain hands-on experience in programming mobile agents through exploration of the source code for a complete mobile agent environment available through the companion website.*Summarizes the state of the art in mobile agent research*Identifies the benefits...

Observation of disorder effects on charged carrier mobility in triphenylene-based discotic materials

International Nuclear Information System (INIS)

Zhang Chunxiu; He, Zhiqun; Mao Huaxiang; Wang Junjie; Wang Dongdong; Wang Yongsheng; Li Zhongxiao; Pu Jialing

2007-01-01

A discotic 2,6,10-trihydroxy-3,7,11-tripentyloxytriphenylene material and a triphenylene-based hyperbranched macromolecule were synthesized, in which the latter was prepared from AB m molecules in a one-pot reaction. Adipic chloride and butyryl chloride were chosen as terminal groups to the 2,6,10-trihydroxy-3,7,11-tripentyloxytriphenylene. Mesophase and their structural orders were determined using a polarized optical microscope and a differential scanning calorimeter. Carrier mobilities of the pure and composite materials were measured via a time-of-flight method. A change in carrier mobility on the morphology of the materials was further discussed. It was found that degree of crystallization was the key for a discotic triphenylene material to possess charge-transporting properties, no matter it is ordered or disordered

Detection and classification of pole-like road objects from mobile LiDAR data in motorway environment

Science.gov (United States)

Yan, Li; Li, Zan; Liu, Hua; Tan, Junxiang; Zhao, Sainan; Chen, Changjun

2017-12-01

Mobile LiDAR Scanning (MLS) can collect 3-dimensional (3D) road and road-related geospatial information accurately and efficiently. Pole-like objects located in road environment are important street furniture and they are necessary information in road inventory and road mapping. The automatic detection and classification of pole-like road objects from mobile LiDAR data can greatly reduce the cost and improve the efficiency. This paper provides a complete workflow for the detection and classification of pole-like road objects from mobile LiDAR data in motorway environment. The major workflow includes three steps: data preprocessing, pole-like road objects detection and pole-like road objects classification. In data preprocessing step, ground points are removed by an automatic ground filtering algorithm, and then off-ground points are clustered into segments and the overlapped segments containing pole-like road objects are further separated through an iterative min-cut based segmentation approach. In detection step, filters utilizing both prior and shape information are used to detect the target objects. In classification step, features of objects are calculated and classified using Random Forest classifier. Our method was tested on two datasets scanned in motorway environment, and the results showed that the Matthews correlation coefficient of the two datasets in detection step was 93.7% and 95.9% respectively and the overall accuracy of the two datasets in classification step was 96.5% and 97.9% respectively.

Content Adaptation for Heterogeneous Mobile Devices using web-based Mobile Services

OpenAIRE

Schmohl, Robert;Baumgarten, Uwe;Köthner, Lars

2017-01-01

Recent advances in mobile computing have spawned a very heterogeneous environment of mobile devices. Those devices have di erent capabilities in providing mobile services to the user, implying the challenge of considering heterogeneous devices during mobile service development. This especially encompasses the task of adapting the content, which a mobile service provides to a specific mobile device. In this paper we present an approach using a service platform, which utilizes a content adaptat...

The value of pre-discharge Duplex scanning in infrainguinal graft surveillance.

Science.gov (United States)

Wilson, Y G; Davies, A H; Currie, I C; McGrath, C; Morgan, M; Baird, R N; Lamont, P M

1995-08-01

Protocols and criteria for Duplex-based graft surveillance programmes (GS) vary widely as to the optimum regimens for maximising detection of "at risk" grafts. Few centres recommend starting GS before discharge. The aim of this study was to audit our experience with respect to early scanning. Vascular Studies Unit, Bristol Royal Infirmary. The records of 123 patients entering GS from January 1992 were reviewed. Patients were scanned at 1 week, 6 weeks and 3, 6, 9 and 12 months post-bypass. Haemodynamic criteria used were a peak mean velocity (PMV) less than 45 cm/s and a focal velocity disturbance with a V2/V1 ratio of 1.5 or more. Forty-six abnormalities (37% detection rate) were identified on scans within one week. In all cases, on-table completion studies with either arteriography and/or flow measurements had failed to identify the anomalies subsequently detected by Duplex. At 1 week, six grafts had occluded, 27 had a focal PMV increase (mean V2/V1 ratio: 2.6; range 1.5-4.3), four had low flow velocities, four had arteriovenous fistulae, one contained mobile thrombus, two had retained cusps and two had hamstring entrapment. Of 40 patent, but compromised grafts, 18 warranted immediate investigation. Of the 27 patients with velocity disturbances on Duplex, 25 were simply observed but, eight have since required intervention for definitive stenoses at these sites which, in retrospect, were evident within the first postoperative week. Pre-discharge scanning is a useful modality for detecting technical problems. Intrinsic graft abnormalities, possibly the sites of future definitive stenoses, have been visualised even at 1 week and once identified, can be more closely scrutinised thereafter. Pre-discharge colour Duplex is recommended as standard practice for quality control after infrainguinal bypass.

Radiopharmaceutical scanning agents

International Nuclear Information System (INIS)

1976-01-01

This invention is directed to dispersions useful in preparing radiopharmaceutical scanning agents, to technetium labelled dispersions, to methods for preparing such dispersions and to their use as scanning agents

Nuclear Heart Scan

Science.gov (United States)

... Home / Nuclear Heart Scan Nuclear Heart Scan Also known as Nuclear Stress Test , ... Learn More Connect With Us Contact Us Directly Policies Privacy Policy Freedom of Information Act (FOIA) Accessibility ...

MutScan: fast detection and visualization of target mutations by scanning FASTQ data.

Science.gov (United States)

Chen, Shifu; Huang, Tanxiao; Wen, Tiexiang; Li, Hong; Xu, Mingyan; Gu, Jia

2018-01-22

Some types of clinical genetic tests, such as cancer testing using circulating tumor DNA (ctDNA), require sensitive detection of known target mutations. However, conventional next-generation sequencing (NGS) data analysis pipelines typically involve different steps of filtering, which may cause miss-detection of key mutations with low frequencies. Variant validation is also indicated for key mutations detected by bioinformatics pipelines. Typically, this process can be executed using alignment visualization tools such as IGV or GenomeBrowse. However, these tools are too heavy and therefore unsuitable for validating mutations in ultra-deep sequencing data. We developed MutScan to address problems of sensitive detection and efficient validation for target mutations. MutScan involves highly optimized string-searching algorithms, which can scan input FASTQ files to grab all reads that support target mutations. The collected supporting reads for each target mutation will be piled up and visualized using web technologies such as HTML and JavaScript. Algorithms such as rolling hash and bloom filter are applied to accelerate scanning and make MutScan applicable to detect or visualize target mutations in a very fast way. MutScan is a tool for the detection and visualization of target mutations by only scanning FASTQ raw data directly. Compared to conventional pipelines, this offers a very high performance, executing about 20 times faster, and offering maximal sensitivity since it can grab mutations with even one single supporting read. MutScan visualizes detected mutations by generating interactive pile-ups using web technologies. These can serve to validate target mutations, thus avoiding false positives. Furthermore, MutScan can visualize all mutation records in a VCF file to HTML pages for cloud-friendly VCF validation. MutScan is an open source tool available at GitHub: https://github.com/OpenGene/MutScan.

LIDAR COMBINED SCANNING UNIT

Directory of Open Access Journals (Sweden)

V. V. Elizarov

2016-11-01

Full Text Available Subject of Research. The results of lidar combined scanning unit development for locating leaks of hydrocarbons are presented The unit enables to perform high-speed scanning of the investigated space in wide and narrow angle fields. Method. Scanning in a wide angular field is produced by one-line scanning path by means of the movable aluminum mirror with a frequency of 20Hz and amplitude of 20 degrees of swing. Narrowband scanning is performed along a spiral path by the deflector. The deflection of the beam is done by rotation of the optical wedges forming part of the deflector at an angle of ±50. The control function of the scanning node is performed by a specialized software product written in C# programming language. Main Results. This scanning unit allows scanning the investigated area at a distance of 50-100 m with spatial resolution at the level of 3 cm. The positioning accuracy of the laser beam in space is 15'. The developed scanning unit gives the possibility to browse the entire investigated area for the time not more than 1 ms at a rotation frequency of each wedge from 50 to 200 Hz. The problem of unambiguous definition of the beam geographical coordinates in space is solved at the software level according to the rotation angles of the mirrors and optical wedges. Lidar system coordinates are determined by means of GPS. Practical Relevance. Development results open the possibility for increasing the spatial resolution of scanning systems of a wide range of lidars and can provide high positioning accuracy of the laser beam in space.

Popular Mobile Phone Apps for Diet and Weight Loss: A Content Analysis.

Science.gov (United States)

Zaidan, Sarah; Roehrer, Erin

2016-07-11

A review of the literature has revealed that the rates of overweight and obesity have been increasing in Australia over the last two decades and that wellness mobile phone apps play a significant role in monitoring and managing individuals' weight. Although mobile phone app markets (iTunes and Google Play) list thousands of mobile phone health apps, it is not always clear whether those apps are supported by credible sources. Likewise, despite the prevailing use of mobile phone apps to aid with weight management, the usability features of these apps are not well characterized. The research explored how usability taxonomy could inform the popularity of downloaded, socially focused wellness mobile phone apps, in particular weight loss and diet apps. The aim of the study was to investigate the Australian mobile phone app stores (iTunes and Google Play) in order to examine the usability features of the most popular (ie, most downloaded) wellness apps. The design of this study comprises 3 main stages: stage 1, identifying apps; stage 2, development of weight loss and diet evaluation framework; and stage 3, application of the evaluation framework. Each stage includes specific data collection, analysis tools, and techniques. The study has resulted in the development of a justified evaluation framework for weight loss and diet mobile phone apps. Applying the evaluation framework to the identified apps has shown that the most downloaded iTunes and Google Play apps are not necessarily the most usable or effective. In addition, the research found that search algorithms for iTunes and Google Play are biased toward apps' titles and keywords that do not accurately define the real functionality of the app. Moreover, the study has also analyzed the apps' user reviews, which served as justification for the developed evaluation framework. The analysis has shown that ease of use, reminder, bar code scanning, motivation, usable for all, and synchronization are significant attributes

A Mobile Asset Tracking System Architecture under Mobile-Stationary Co-Existing WSNs

Science.gov (United States)

Kim, Tae Hyon; Jo, Hyeong Gon; Lee, Jae Shin; Kang, Soon Ju

2012-01-01

The tracking of multiple wireless mobile nodes is not easy with current legacy WSN technologies, due to their inherent technical complexity, especially when heavy traffic and frequent movement of mobile nodes are encountered. To enable mobile asset tracking under these legacy WSN systems, it is necessary to design a specific system architecture that can manage numerous mobile nodes attached to mobile assets. In this paper, we present a practical system architecture including a communication protocol, a three-tier network, and server-side middleware for mobile asset tracking in legacy WSNs consisting of mobile-stationary co-existing infrastructures, and we prove the functionality of this architecture through careful evaluation in a test bed. Evaluation was carried out in a microwave anechoic chamber as well as on a straight road near our office. We evaluated communication mobility performance between mobile and stationary nodes, location-awareness performance, system stability under numerous mobile node conditions, and the successful packet transfer rate according to the speed of the mobile nodes. The results indicate that the proposed architecture is sufficiently robust for application in realistic mobile asset tracking services that require a large number of mobile nodes. PMID:23242277

A Mobile Asset Tracking System Architecture under Mobile-Stationary Co-Existing WSNs

Directory of Open Access Journals (Sweden)

Soon Ju Kang

2012-12-01

Full Text Available The tracking of multiple wireless mobile nodes is not easy with current legacy WSN technologies, due to their inherent technical complexity, especially when heavy traffic and frequent movement of mobile nodes are encountered. To enable mobile asset tracking under these legacy WSN systems, it is necessary to design a specific system architecture that can manage numerous mobile nodes attached to mobile assets. In this paper, we present a practical system architecture including a communication protocol, a three-tier network, and server-side middleware for mobile asset tracking in legacy WSNs consisting of mobile-stationary co-existing infrastructures, and we prove the functionality of this architecture through careful evaluation in a test bed. Evaluation was carried out in a microwave anechoic chamber as well as on a straight road near our office. We evaluated communication mobility performance between mobile and stationary nodes, location-awareness performance, system stability under numerous mobile node conditions, and the successful packet transfer rate according to the speed of the mobile nodes. The results indicate that the proposed architecture is sufficiently robust for application in realistic mobile asset tracking services that require a large number of mobile nodes.

Mobile marketing

OpenAIRE

Gause, Matěj

2012-01-01

The goal of bachelor's thesis on the theme "Mobile marketing" is to outline its development and why is this new phenomen so important for all modern companies around the world. The work is not about simple description of mobile marketing media but it vividly informs about the latest trends and news from the world of mobile apps and games. It presents the most successful mobile apps which registered more than billion downloads and from their unique characteristics it unveils great potential of...

In vitro wear assessments of fixed and mobile UHMWPE total knee replacement

International Nuclear Information System (INIS)

Affatato, Saverio; Bracco, Pierangiola; Sudanese, Alessandra

2013-01-01

Highlights: ► In this study we examined the wear behaviour of total knee UHMWPE menisci. ► We used two different knee designs: mobile and fixed menisci. ► We used a knee simulator and FTIR analyses to evaluate the wear behaviour. ► Our conclusions are that the two designs had a different wear behaviour. - Abstract: This work discusses the wear behaviour of two different ultra-high-molecular-weight-polyethylene tibial component designs. Mobile and fixed bearings were tested on a knee wear simulator for 5 million cycles using bovine calf serum as lubricant. We correlated the wear results with the chemical characterisation of the investigated materials: Fourier Transformed Infra Red Spectroscopy analyses, Differential Scanning Calorimetry and cross-link density measurements were used to assess the chemical features of this polyethylene. Mobile and fixed polyethylene inserts showed a different wear behaviour: the mobile designs components showed lower weight losses than the fixed components (109 ± 6 mg and 163 ± 80 mg, respectively). Significant statistical differences were observed in wear rate (P = 0.035, Kolmogorov–Smirnov Test for two samples). From a molecular point of view, typical radiation-induced oxidation profiles were observed in all the tested polyethylene samples, but the overall degradation was more significant in the fixed bearing inserts and this is likely to play a role on the wear performances

Staging Mobilities

DEFF Research Database (Denmark)

Jensen, Ole B.

and lived as people are “staging themselves” (from below). Staging mobilities is a dynamic process between “being staged” (for example, being stopped at traffic lights) and the “mobile staging” of interacting individuals (negotiating a passage on the pavement). Staging Mobilities is about the fact...

Changes in urination according to the sound of running water using a mobile phone application.

Science.gov (United States)

Kwon, Whi-An; Kim, Sung Han; Kim, Sohee; Joung, Jae Young; Chung, Jinsoo; Lee, Kang Hyun; Lee, Sang-Jin; Seo, Ho Kyung

2015-01-01

The sound of running water (SRW) has been effectively used for toilet training during toddlerhood. However, the effect of SRW on voiding functions in adult males with lower urinary tract symptoms (LUTS) has not been evaluated. To determine the effect of SRW on urination in male patients with LUTS, multiple voiding parameters of uroflowmetry with postvoid residual urine (PVR) were assessed according to the presence of SRW played by a mobile application. Eighteen consecutive male patients with LUTS were prospectively enrolled between March and April 2014. Uroflowmetry with PVR measured by a bladder scan was randomly performed once weekly for two consecutive weeks with and without SRW in a completely sealed room after pre-checked bladder volume was scanned to be more than 150 cc. SRW was played with river water sounds amongst relaxed melodies from a smartphone mobile application. The mean age of enrolled patients and their mean International Prostate Symptom Score (IPSS) were 58.9 ± 7.7 years (range: 46-70) and 13.1 ± 5.9, respectively. All patients had not been prescribed any medications, including alpha-blockers or anti-muscarinic agents, in the last 3 months. There was a significant increase in mean peak flow rate (PFR) with SRW in comparison to without SRW (15.7 mL/s vs. 12.3 mL/s, respectively, p = 0.0125). However, there were no differences in other uroflowmetric parameters, including PVR. The study showed that SRW from a mobile phone application may be helpful in facilitating voiding functions by increasing PFR in male LUTS patients.

RBC nuclear scan

Science.gov (United States)

... page: //medlineplus.gov/ency/article/003835.htm RBC nuclear scan To use the sharing features on this page, please enable JavaScript. An RBC nuclear scan uses small amounts of radioactive material to ...

Interdependent, imagined, and embodied mobilities in mobile social space

NARCIS (Netherlands)

Murray, Lesley; Doughty, Karolina

2016-01-01

This article draws on ethnographic research of everyday mobilities to further understanding of interdependent mobilities practices in relation to normality, habit and routine. The contention here is that a rethinking of ‘normality’, ‘habit’ and ‘routine’ reveals how mobilities are interdependent,

Year-Round Use Of Thermography In House Doctoring

Science.gov (United States)

Gadsby, Kenneth J.; Harrje, David T.; Dutt, Gautam S.

1983-03-01

There have been many presentations of thermographic residential building analyses at the past ThermosInse conferences. A number of these papers have dealt with evaluation of insulation voids and more recently a few have described air leakage detection 2,3 during the colder winter months. This paper will focus on the thermographic application in the House Doctor instrumented energy analysis approach as developed by Princeton University. The central theme will be the application to a year-round research or commercial activity. Some of the conditions that could create thermographic problems, as well as techniques that may be used to lessen these difficulties, thereby extending the thermographic "season" is discussed. Our experiences in summer thermography with and without the use of a building pressurization system is also covered.

MOBILE TRAFFIC ALERT AND TOURIST ROUTE GUIDANCE SYSTEM DESIGN USING GEOSPATIAL DATA

Directory of Open Access Journals (Sweden)

D. Bhattacharya

2017-09-01

Full Text Available The present study describes an integrated system for traffic data collection and alert warning. Geographical information based decision making related to traffic destinations and routes is proposed through the design. The system includes a geospatial database having profile relating to a user of a mobile device. The processing and understanding of scanned maps, other digital data input leads to route guidance. The system includes a server configured to receive traffic information relating to a route and location information relating to the mobile device. Server is configured to send a traffic alert to the mobile device when the traffic information and the location information indicate that the mobile device is traveling toward traffic congestion. Proposed system has geospatial and mobile data sets pertaining to Bangalore city in India. It is envisaged to be helpful for touristic purposes as a route guidance and alert relaying information system to tourists for proximity to sites worth seeing in a city they have entered into. The system is modular in architecture and the novelty lies in integration of different modules carrying different technologies for a complete traffic information system. Generic information processing and delivery system has been tested to be functional and speedy under test geospatial domains. In a restricted prototype model with geo-referenced route data required information has been delivered correctly over sustained trials to designated cell numbers, with average time frame of 27.5 seconds, maximum 50 and minimum 5 seconds. Traffic geo-data set trials testing is underway.

Subversive Mobilities

DEFF Research Database (Denmark)

Thelle, Mikkel

2013-01-01

The article approaches mobility through a cultural history of urban conflict. Using a case of “The Copenhagen Trouble,“ a series of riots in the Danish capital around 1900, a space of subversive mobilities is delineated. These turn-of-the-century riots points to a new pattern of mobile gathering...

DepositScan, a Scanning Program to Measure Spray Deposition Distributions

Science.gov (United States)

DepositScan, a scanning program was developed to quickly measure spray deposit distributions on water sensitive papers or Kromekote cards which are widely used for determinations of pesticide spray deposition quality on target areas. The program is installed in a portable computer and works with a ...

Large Scale Scanning Probe Microscope "Making Shear Force Scanning visible."

NARCIS (Netherlands)

Bosma, E.; Offerhaus, Herman L.; van der Veen, Jan T.; van der Veen, J.T.; Segerink, Franciscus B.; Wessel, I.M.

2010-01-01

We describe a demonstration of a scanning probe microscope with shear-force tuning fork feedback. The tuning fork is several centimeters long, and the rigid fiber is replaced by a toothpick. By scaling this demonstration to visible dimensions the accessibility of shear-force scanning and tuning fork

Mobile media, mobility and mobilisation in the current museum field

DEFF Research Database (Denmark)

Baggesen, Rikke Haller

2017-01-01

Introducing the concept of a 'mobile museology' to describe how museums are currently set in motion by a confluence of cultural, technological and museological developments, this chapter traces the connections between mobile media and notions of mobility and mobilisation in the museum field....... As illustrated by current examples in the chapter, mobile phones have thus provided an opportunity for both augmenting and transcending the museum space, blurring former boundaries between institutions and their environments. At the same time, technological advances and digitial culture developments have also...... required and inspired museums to become organisationally mobile, and to mobilise collections, audiences and institutions in order to fulfill museum missions. In this perspective, mobile media are thus seen as both catalysts and instruments for current museum developments....

Nontraumatic tibial polyethylene insert cone fracture in mobile-bearing posterior-stabilized total knee arthroplasty

OpenAIRE

Tanikake, Yohei; Hayashi, Koji; Ogawa, Munehiro; Inagaki, Yusuke; Kawate, Kenji; Tomita, Tetsuya; Tanaka, Yasuhito

2016-01-01

A 72-year-old male patient underwent mobile-bearing posterior-stabilized total knee arthroplasty for osteoarthritis. He experienced a nontraumatic polyethylene tibial insert cone fracture 27 months after surgery. Scanning electron microscopy of the fracture surface of the tibial insert cone suggested progress of ductile breaking from the posterior toward the anterior of the cone due to repeated longitudinal bending stress, leading to fatigue breaking at the anterior side of the cone, followed...

The Future of Mobile Apps in Travel Booking : Which mobile solutions might shape organizations’ mobile development?

OpenAIRE

Caglayan, Sibel

2017-01-01

The objective of this Thesis was to dive into the world of mobile travel booking in order to find out which kinds of mobile technologies travel booking applications might adopt in the future. Furthermore, to find out whether or not there are mobile solutions coming up that might challenge the existence of apps. Travel booking is a versatile industry with many different aspects to it, especially in mobile booking solutions. The research was conducted by using primary and secondary research met...

Mobil marketing

OpenAIRE

Engelová, Kateřina

2006-01-01

Mobil marketing - reklama a podpora prodeje prostřednictvím mobilních telefonů. Technologické a kulturní předpoklady vzniku tohoto odvětví. Mobil marketing a marketingový mix, možnosti synergie. Nástroje mobil marketingu - reklamní SMS a MMS, lokační služby, soutěže, ankety a hlasování, věrnostní systémy, mobilní obsah. Subjekty mobil marketingu. M-komerce. Využití pro podnikové aplikace.

MOBILITY: A SYSTEMS APPROACH

Directory of Open Access Journals (Sweden)

Mykola I. Striuk

2015-10-01

Full Text Available A comprehensive study on the problem of mobility in the socio-educational and technical systems was carried out: the evolution of the concept of mobility in scientific sources of XIX–XXI centuries was analyzed and the new sources on the issue of mobility introduced into scientific circulation, the interrelation of the types of mobility in the socio-pedagogical and technical systems are theoretically grounded, an integrative model of mobility in the information society is proposed. The major trends in academic mobility are identified (the transition from student mobility to mobility programs and educational services providers, the new mobility programs (franchising, double/joint degrees, combinations, nostrification etc. are characterized. The new types of mobility providers are reviewed and attention is focused on virtual universities that are now the basis of virtual mobility of students and activities which are based on the use of new ICT in higher education, especially – the Internet and mobile learning environments.

Mobile systems development

DEFF Research Database (Denmark)

Pedersen, Ole; Kristiansen, Martin Lund; Kammersgaard, Marc N.

2007-01-01

in XP. In general, we find XP well-suited for mobile systems development projects. However, based on our experiences and an analytical comparison we propose the following modifications to XP: Make an essential design to avoid the worst time waste during refactoring. For faster development, reuse code......Development of mobile software is Surrounded by much uncertainty. Immature software platforms on mobile clients, a highly competitive market calling for innovation, efficiency and effectiveness in the development life cycle, and lacking end-user adoption are just some of the realities facing...... development teams in the mobile software industry. By taking a process view on development of mobile systems we seek to explore the strengths and limitations of eXtreme Programming (XP) in the context of mobile software development. Following an experimental approach a mobile systems development project...

System Architecture and Mobility Management for Mobile Immersive Communications

Directory of Open Access Journals (Sweden)

Mehran Dowlatshahi

2007-01-01

Full Text Available We propose a system design for delivery of immersive communications to mobile wireless devices based on a distributed proxy model. It is demonstrated that this architecture addresses key technical challenges for the delivery of these services, that is, constraints on link capacity and power consumption in mobile devices. However, additional complexity is introduced with respect to application layer mobility management. The paper proposes three possible methods for updating proxy assignments in response to mobility management and compares the performance of these methods.

Mobile Operating Systems

OpenAIRE

Vipin Kamboj; Hitesh Gupta

2012-01-01

Mobile phones are used by every people in today’s life. We use mobile phones without knowing the different factors that a mobile used including its technology, operating system, CPU ,RAM etc. Many types of operating system are used by different mobile. Every operating system has their advantage

Mobile probes

DEFF Research Database (Denmark)

Ørngreen, Rikke; Jørgensen, Anna Neustrup; Noesgaard, Signe Schack

2016-01-01

A project investigating the effectiveness of a collection of online resources for teachers' professional development used mobile probes as a data collection method. Teachers received questions and tasks on their mobile in a dialogic manner while in their everyday context as opposed...... to in an interview. This method provided valuable insight into the contextual use, i.e. how did the online resource transfer to the work practice. However, the research team also found that mobile probes may provide the scaffolding necessary for individual and peer learning at a very local (intra-school) community...... level. This paper is an initial investigation of how the mobile probes process proved to engage teachers in their efforts to improve teaching. It also highlights some of the barriers emerging when applying mobile probes as a scaffold for learning....

Mobility Challenges

DEFF Research Database (Denmark)

Jensen, Ole B.; Lassen, Claus

2011-01-01

This article takes point of departure in the challenges to understand the importance of contemporary mobility. The approach advocated is a cross-disciplinary one drawing on sociology, geography, urban planning and design, and cultural studies. As such the perspective is to be seen as a part...... of the so-called ‘mobility turn’ within social science. The perspective is illustrative for the research efforts at the Centre for Mobility and Urban Studies (C-MUS), Aalborg University. The article presents the contours of a theoretical perspective meeting the challenges to research into contemporary urban...... mobilities. In particular the article discusses 1) the physical city, its infrastructures and technological hardware/software, 2) policies and planning strategies for urban mobility and 3) the lived everyday life in the city and the region....

Scanning of bone metastases

International Nuclear Information System (INIS)

Robillard, J.

1977-01-01

The Centers against cancer of Caen, Angers, Montpellier, Strasbourg and 'the Curie Foundation' have confronted their experience in detection of bone metastases by total body scanning. From the investigation by this procedure, of 1,467 patients with cancer, it results: the confrontation between radio and scanning shows a rate of false positive and false negative identical to the literature ones; the countage scanning allows to reduce the number of false positive; scanning allows to direct bone biopsy and to improve efficiency of histological examination [fr

Transverse section scanning mechanism

International Nuclear Information System (INIS)

Doherty, E.J.

1978-01-01

Apparatus is described for scanning a transverse, radionuclide scan-field using an array of focussed collimators. The collimators are movable tangentially on rails, driven by a single motor via a coupled screw. The collimators are also movable in a radial direction on rails driven by a step motor via coupled screws and bevel gears. Adjacent bevel gears rotate in opposite directions so adjacent collimators move in radially opposite directions. In use, the focal point of each collimator scans at least half of the scan-field, e.g. a human head located in the central aperture, and the electrical outputs of detectors associated with each collimator are used to determine the distribution of radioactive emission intensity at a number of points in the scan-field. (author)

Mobility2.0: co-operative ITS systems for enhanced electric vehicle mobility

NARCIS (Netherlands)

Unknown, [Unknown; Dimitrova, D.C.; Brogle, M.; Braun, T.; Heijenk, Gerhard J.

Mobility2.0 will develop and test an in-vehicle commuting assistant for FEV mobility, resulting in more reliable and energy-efficient electro-mobility. In order to achieve a maximum impact, Mobility2.0 takes an integrated approach of ad- dressing the main bottlenecks of urban FEV mobility: range

Scanning ARM Cloud Radars Part II. Data Quality Control and Processing

Energy Technology Data Exchange (ETDEWEB)

Kollias, Pavlos [McGill Univ., Montreal, QC (Canada); Jo, Ieng [McGill Univ., Montreal, QC (Canada); Borque, Paloma [McGill Univ., Montreal, QC (Canada); Tatarevic, Aleksandra [McGill Univ., Montreal, QC (Canada); Lamer, Katia [McGill Univ., Montreal, QC (Canada); Bharadwaj, Nitin [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Widener, Kevin B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Johnson, Karen [Brookhaven National Lab. (BNL), Upton, NY (United States); Clothiaux, Eugene E. [Pennsylvania State Univ., State College, PA (United States)

2013-10-04

The Scanning ARM Cloud Radars (SACR’s) are the primary instruments for documenting the four-dimensional structure and evolution of clouds within a 20-30 km radius from the ARM fixed and mobile sites. Here, the post-processing of the calibrated SACR measurements is discussed. First, a feature mask algorithm that objectively determines the presence of significant radar returns is described. The feature mask algorithm is based on the statistical properties of radar receiver noise. It accounts for atmospheric emission and is applicable even for SACR profiles with few or no signal-free range gates. Using the nearest-in-time atmospheric sounding, the SACR radar reflectivities are corrected for gaseous attenuation (water vapor and oxygen) using a line-by-line absorption model. Despite having a high pulse repetition frequency, the SACR has a narrow Nyquist velocity limit and thus Doppler velocity folding is commonly observed. An unfolding algorithm that makes use of a first guess for the true Doppler velocity using horizontal wind measurements from the nearest sounding is described. The retrieval of the horizontal wind profile from the Hemispherical Sky – Range Height Indicator SACR scan observations and/or nearest sounding is described. The retrieved horizontal wind profile can be used to adaptively configure SACR scan strategies that depend on wind direction. Several remaining challenges are discussed, including the removal of insect and second-trip echoes. The described algorithms significantly enhance SACR data quality and constitute an important step towards the utilization of SACR measurements for cloud research.

Connecting Mobile Users Through Mobile Social Networks

Directory of Open Access Journals (Sweden)

Faisal Alkhateeb

2012-10-01

Full Text Available Nowadays, social networks become popular with the emerging of web-based social networking services. Recently, several mobile services are developed to connect users to their favourite social networks such as Facebook, Twitter, Flickr, etc. However, these services depends upon the existing web-based social networks. In this paper, we present a mobile service for joining groups across communities. The originality of the work is that the framework of the service allows creating and joining social networks that are self-contained for mobile company servers. The service consists of several sub-services such as users invitation, group finding and others. Users, regardless of their disability, can use the service and its sub-services without the need to create their own accounts on social web sites and thus their own groups. We also propose a privacy control policy for mobile social networks.

Nontraumatic tibial polyethylene insert cone fracture in mobile-bearing posterior-stabilized total knee arthroplasty

Directory of Open Access Journals (Sweden)

Yohei Tanikake

2016-12-01

Full Text Available A 72-year-old male patient underwent mobile-bearing posterior-stabilized total knee arthroplasty for osteoarthritis. He experienced a nontraumatic polyethylene tibial insert cone fracture 27 months after surgery. Scanning electron microscopy of the fracture surface of the tibial insert cone suggested progress of ductile breaking from the posterior toward the anterior of the cone due to repeated longitudinal bending stress, leading to fatigue breaking at the anterior side of the cone, followed by the tibial insert cone fracture at the anterior side of the cone, resulting in fracture at the base of the cone. This analysis shows the risk of tibial insert cone fracture due to longitudinal stress in mobile-bearing posterior-stabilized total knee arthroplasty in which an insert is designed to highly conform to the femoral component.

High mobility amorphous InGaZnO{sub 4} thin film transistors formed by CO{sub 2} laser spike annealing

Energy Technology Data Exchange (ETDEWEB)

Chung, Chen-Yang; Zhu, Bin; Ast, Dieter G.; Thompson, Michael O. [Department of Materials Science and Engineering, Cornell University, Ithaca, New York 14853 (United States); Greene, Raymond G. [Corning Incorporated, Corning, New York 14831 (United States)

2015-03-23

Amorphous InGaZnO{sub 4} (a-IGZO) thin film transistors (TFTs) hold great potential for large area and flexible electronics with current research focused on improving the mobility and stability. In this work, we report on properties of IGZO TFTs fabricated using laser spike annealing (LSA) with a scanned continuous wave CO{sub 2} laser. For peak annealing temperatures near 430 °C and a 1 ms dwell, TFTs exhibit saturation field-effect mobilities above 70 cm{sup 2}/V-s (V{sub on} ∼ −3 V), a value over 4 times higher than furnace-annealed control samples (∼16 cm{sup 2}/V-s). A model linking oxygen deficient defect structures with limited structural relaxation after the LSA anneal is proposed to explain the observed high mobility. This mobility is also shown to be comparable to the estimated trap-free mobility in oxide semiconductors and suggests that shallow traps can be removed by transient thermal annealing under optimized conditions.

Staging Mobilities / Designing Mobilities

DEFF Research Database (Denmark)

Jensen, Ole B.

2015-01-01

, and systems 'hosting' these multiple and complex mobilities are designed and how they are staging these in terms of their physical layout. By analysing specific cases of ‘mobilities design’ related to the four modes of moving; Walk, Bike, Train, and Car, the book uncover important and until now neglected...... is more than movement between point A and B. It explores how the movement of people, goods, information, and signs influences human understandings of self, other and the built environment. Moving towards a new understanding of the relationship between movement, interaction and environments, the project...

Mobile platform security

CERN Document Server

Asokan, N; Dmitrienko, Alexandra

2013-01-01

Recently, mobile security has garnered considerable interest in both the research community and industry due to the popularity of smartphones. The current smartphone platforms are open systems that allow application development, also for malicious parties. To protect the mobile device, its user, and other mobile ecosystem stakeholders such as network operators, application execution is controlled by a platform security architecture. This book explores how such mobile platform security architectures work. We present a generic model for mobile platform security architectures: the model illustrat

RubiShort: Reducing scan time in 82Rb heart scans to minimize movements artifacts

DEFF Research Database (Denmark)

Madsen, Jeppe; Vraa, Kaspar J.; Harms, Hans

.013x, R2=0.98; %Reversible: y=1.008x, R2=0.95; TPD: y=1.000x, R2=0.99). Conclusion:, Scan time of myocardial perfusion scans using 82Rb can be reduced from 7 min. to 5 min. without loss of quantitative accuracy. Since patient motion is frequent in the last minutes of the scans, scan time reduction...

Use of multidetector-row computed tomography scan to detect pannus formation in prosthetic mechanical aortic valves.

Science.gov (United States)

Aladmawi, Mohamed A; Pragliola, Claudio; Vriz, Olga; Galzerano, Domenico

2017-04-01

Obstruction of a mechanical aortic valve by pannus formation at the subvalvular level is a major long-term complication of aortic valve replacement (AVR). In fact, pannus is sometime difficult to differentiate from patient-prosthesis mismatch or valve thrombosis. In most cases cine-angiography and echocardiography, either transthoracic or transesophageal, cannot correctly visualize the complication when the leaflets show a normal mobility. Recent technological refinements made this difficult diagnosis possible by ECG-gated computed tomography (CT) scan which shows adequate images in 90% of the cases and can differentiate pannus from fresh and organized thrombus.

Analisis Unjuk Kerja Horizontal Handover Mobile Wimax Mendukung Layanan Mobile TV

Directory of Open Access Journals (Sweden)

Ammatia Risty

2016-05-01

Full Text Available IEEE 802.16e-2005 teknologi mobile WiMAX merupakan salah satu alternatif yang dapat memberikan datarate 15 Mbps yang lebih baik daripada teknologi 3G, WLAN, dan lain-lain. Mobile WiMAX juga memberikan cakupan area yang luas. Oleh karena itu, WiMAX mampu memberikan layanan berbagai macam aplikasi multimedia seperti VoIP, IPTV, Video conferencing. dan aplikasi real-time lainnya. Selain itu, Mobile WiMAX juga mendukung mobility secara portable, mobile, dan nomadic. Saat ini IPTV muncul pada mobile phone, yang dinamakan mobile TV dimana layanan IPTV akan dapat diakses dalam keadaan bergerak. Hal itu membutuhkan suatu teknologi yang mendukung mobility namun tetap dapat menerima layanan IPTV dengan baik. Teknologi mobile WiMAX adalah teknologi yang cocok untuk mendukung layanan IPTV khususnya untuk user yang sedang bergerak. Akibat dari user yang bergerak maka memungkinkan user tersebut melakukan handover. Penelitian ini menganalisis parameter unjuk kerja yang mempengaruhi pada mobile TV saat user melakukan  handover  pada jaringan mobile WiMAX seperti jitter, end to end delay, throughput, handover delay dengan skenario perbedaan kecepatan dan perubahan jumlah user dalam satu cakupan area. Berdasarkan hasil simulasi untuk skenario perbedaan kecepatan (maksimum 100 km/jam diperoleh nilai end to end delay sebesar 23.234 ms, jitter sebesar 0.047 ms, throughput sebesar 637.723 Kbps. Sedangkan skenario jumlah user diperoleh nilai end to end delay 27.218 ms, jitter sebesar 0.057 ms, throughput sebesar 558.881 Kbps. Hasil dari kedua skenario menunjukkan bahwa saat kecepatan dan jumlah user naik maka parameter kualitas layanan turun namun masih memenuhi syarat kualitas layanan Mobile TV (IPTV.

CT scanning in pediatric head trauma: correlation of clinical features with CT scan diagnosis

International Nuclear Information System (INIS)

Arkoncel, Mary Ann P.; Posadas, Ma. Belen A.

1997-01-01

A retrospective review was conducted on 205 cases of pediatric head trauma for which cranial computed tomography scans were done at the Makati Medical Center, to determine which clinical features might positively predict an abnormality on CT scan. The clinical findings of loss of consciousness, GCS < 12, vomiting headache, seizures, and focal abnormalities on Neurologic Examination were significantly associated with abnormal findings on CT scan. However, a significant discrepancy does exist as to how accurately clinical findings do in fact predict normal and abnormal CT scan findings. Such a discrepancy allows us to conclude that a more liberal use of CT Scanning in cases of pediatric head trauma must be stressed to insure proper diagnosis. This study shows that when a patient presents with the aforementioned positive signs and symptoms, or with a focal neurologic deficit, or in combination, a 60-100 % positive prediction of abnormal CT Scan can be made. However, prediction of normal CT Scan is only 0-40%. (Author)

Wapice News Mobile Application

OpenAIRE

Söylemez, Ilke

2017-01-01

Since the mobile phones started to have an increasingly significant role in daily life, the mobile application development also started to be an important area in the software industry. The problem for mobile application developers is to develop a mobile application which supports all the devices and platforms on the market. This issue created a need for cross platform mobile applications. The cross platform mobile development refers to the development of mobile applications that could be use...

Mobilizing Senior Citizens in Co-Design of Mobile Technology

DEFF Research Database (Denmark)

Malmborg, Lone; Gronvall, Erik; Messeter, Jörn

2016-01-01

. Based on the notions of design culture, communities of everyday practice and situated elderliness we present accounts from two European countries, and discuss methodological issues related to mobilizing senior citizens in co-design work as they have manifested themselves and influenced the Give......This paper disseminates work from the European Give&Take project, which aims at co-designing service sharing among senior citizens based on a mobile and distributed platform. With this project as a frame, our paper addresses methodological considerations of participation in co-design for ageing......&Take project. Challenges for mobilization are identified, based on an analysis of attitudes and values among design researchers and senior citizens. This analysis lead us to identify and discuss three strategies for mobilizing senior citizens in co-design of mobile technology: 1) Understanding being ‘elderly...

The Effects of Trust Transference, Mobile Attributes and Enjoyment on Mobile Trust

Directory of Open Access Journals (Sweden)

Cristiane Junqueira Giovannini

2015-01-01

Full Text Available Trust is essential in building relationships. In mobile commerce, as in electronic commerce, trust is even more valuable given the absence of human contact and direct observation of the service provider. Despite the importance of trust for mobile commerce, there has been little academic effort to study the relationships between mobile devices unique components of interactivity and customer trust, or the relationship between offline, online and mobile trust. This study proposes a trust-mediated model for customer attitude and transaction intentions in mobile commerce contexts that incorporates trust transference and unique factors present in mobile commerce. Data were collected in an online survey and analyzed via structural equations modeling. Results suggest that trust transferred from online contexts and ease of use have significant effects on mobile trust formation, while also indicating that mobile trust influences consumers’ attitudes and intentions to purchase using mobile devices.

Intensive mobilities

DEFF Research Database (Denmark)

Vannini, Phillip; Bissell, David; Jensen, Ole B.

with fieldwork conducted in Canada, Denmark and Australia to develop our understanding of the experiential politics of long distance workers. Rather than focusing on the extensive dimensions of mobilities that are implicated in patterns and trends, our paper turns to the intensive dimensions of this experience......This paper explores the intensities of long distance commuting journeys as a way of exploring how bodily sensibilities are being changed by the mobilities that they undertake. The context of this paper is that many people are travelling further to work than ever before owing to a variety of factors...... which relate to transport, housing and employment. Yet we argue that the experiential dimensions of long distance mobilities have not received the attention that they deserve within geographical research on mobilities. This paper combines ideas from mobilities research and contemporary social theory...

Designing Mobilities

DEFF Research Database (Denmark)

Jensen, Ole B.

are often still not engaged with in a sufficiently manner. Often social sciences keep distance to the physical and material as if the social was still to be understood as a realm separate of technology, architecture, and design (for a critique of this see; Latour 2005 and Urry 2000). This paper takes point......Within the so-called ‘mobilities turn’ (Adey 2010; Cresswell 2006; Urry 2007) much research has taken place during the last decade bringing mobilities into the centre of sociological analysis. However, the materiality and spatiality of artefacts, infrastructures, and sites hosting mobilities...... of departure in the sociological perspective termed ‘Staging Mobilities’ (Jensen 2013a) and utilizes this as an analytical frame for exploring cases of mobility design. The paper put focus on how the material shape, design and architectures of technologies, spaces and sites influence mobilities practices...

Restricted Mobilities

DEFF Research Database (Denmark)

Nielsen, Mette; Lassen, Claus

2012-01-01

communities and shopping centres through mobility lenses. The article shows how different mobility systems enable and restrict the public access to private-public spaces, and it points out that proprietary communities create an unequal potential for human movement and access in the city. The main argument......Privatisation of public spaces in the contemporary city has increased during the last decades but only few studies have approached this field from a mobility perspective. Therefore the article seeks to rectify this by exploring two Australian examples of private spaces in the city; gated...... and stratification mechanisms. In conclusion the article therefore suggests that future urban research and planning also needs a mobile understanding of spaces in the cities and how different mobility systems play an important role to sustain the exclusiveness that often characterises the private/public spaces...

Evolution of Mobile Applications

Directory of Open Access Journals (Sweden)

Phongtraychack Anachack

2018-01-01

Full Text Available Currently, we can see the rapid evolution of mobile technology, which involves mobile communication, mobile hardware, and mobile software. Features of mobile phones largely depend on software. In contemporary information and communication age [1–4], mobile application is one of the most concerned and rapidly developing areas. At the same time, the development of mobile application undergoes great changes with the introduction of new software, service platforms and software development kits (SDK. These changes lead to appearance of many new service platforms such as Google with Android and Apple with iOS. This article presents the information about the evolution of mobile application, gives some statistical data on the past and present situation, demonstrates how individual users of mobile devices can benefit, and shows how mobile applications affect society from the ethical perspective.

European mobility cultures

DEFF Research Database (Denmark)

Haustein, Sonja; Nielsen, Thomas A. Sick

2016-01-01

More targeted European policies promoting green travel patterns require better knowledge on differing mobility cultures across European regions. As a basis for this, we clustered the EU population into eight mobility styles based on Eurobarometer data. The mobility styles - including, for example...... positions on the path towards sustainable mobility and therefore different requirements towards European platforms and support measures, e.g. for 'Sustainable Urban Mobility Plans'. The country clusters can provide a starting point for future communication and targeting of European efforts in sustainable...

Helios: a Multi-Purpose LIDAR Simulation Framework for Research, Planning and Training of Laser Scanning Operations with Airborne, Ground-Based Mobile and Stationary Platforms

Science.gov (United States)

Bechtold, S.; Höfle, B.

2016-06-01

In many technical domains of modern society, there is a growing demand for fast, precise and automatic acquisition of digital 3D models of a wide variety of physical objects and environments. Laser scanning is a popular and widely used technology to cover this demand, but it is also expensive and complex to use to its full potential. However, there might exist scenarios where the operation of a real laser scanner could be replaced by a computer simulation, in order to save time and costs. This includes scenarios like teaching and training of laser scanning, development of new scanner hardware and scanning methods, or generation of artificial scan data sets to support the development of point cloud processing and analysis algorithms. To test the feasibility of this idea, we have developed a highly flexible laser scanning simulation framework named Heidelberg LiDAR Operations Simulator (HELIOS). HELIOS is implemented as a Java library and split up into a core component and multiple extension modules. Extensible Markup Language (XML) is used to define scanner, platform and scene models and to configure the behaviour of modules. Modules were developed and implemented for (1) loading of simulation assets and configuration (i.e. 3D scene models, scanner definitions, survey descriptions etc.), (2) playback of XML survey descriptions, (3) TLS survey planning (i.e. automatic computation of recommended scanning positions) and (4) interactive real-time 3D visualization of simulated surveys. As a proof of concept, we show the results of two experiments: First, a survey planning test in a scene that was specifically created to evaluate the quality of the survey planning algorithm. Second, a simulated TLS scan of a crop field in a precision farming scenario. The results show that HELIOS fulfills its design goals.

Mobilizing community energy

International Nuclear Information System (INIS)

Bomberg, Elizabeth; McEwen, Nicola

2012-01-01

What explains the galvanising of communities to participate actively in energy projects? How do groups mobilize to overcome the often formidable barriers highlighted in the existing literature? Drawing on original qualitative research of 100 community energy groups in Scotland, including six in-depth case studies, we explain how effective mobilization occurs and the political dynamics surrounding such mobilization. To capture these dynamics, we adapt theories offered by literature on social movements, with a particular focus on resource mobilization theories. Applying our adapted framework, we identify two particular sets of resources shaping community energy mobilization: (i) structural resources, which refer to the broad political context structuring and constraining opportunities for community energy mobilization; and (ii) symbolic resources—less tangible resources used to galvanise participants. We investigate to what extent our case study groups were able to draw upon and exploit these resources. We find that structural resources can either facilitate or hinder mobilization; what matters is how state resources are exploited and constraints mitigated. The use of symbolic resources was highly effective in aiding mobilization. Each of the groups examined – despite their considerable variation – effectively exploited symbolic resources such as shared identity or desire for strong, self reliant communities. - Highlights: ► Explains how/why community energy groups mobilize and the political dynamics surrounding it. ► Draws on original qualitative research of 100 community energy groups in Scotland. ► Identifies two particular sets of resources (structural and symbolic) and their importance. ► Explains how these resources shape community energy mobilization in Scotland. ► Provides an original application of resource mobilization theory to the field of energy studies.

Understanding pastoral mobility

DEFF Research Database (Denmark)

Adriansen, Hanne Kirstine

2008-01-01

Based on a case study from Sahelian Senegal, this paper analyses how various actors perceive the importance of pastoral mobility and presents issues of importance for understanding the use of mobility among Fulani of Ferlo. One knowledge system is a scientific one, the 'new rangeland paradigm...... territory, which they consider their place, but are unwilling to employ large-scale mobility themselves. Mobility is not of importance for their ethnic identity and some use paid herders to care for their livestock. By looking at both knowledge systems, we achieve a better understanding of pastoral mobility...

Mobile Design Pattern Gallery UI Patterns for Mobile Applications

CERN Document Server

Neil, Theresa

2012-01-01

When you're under pressure to produce a well designed, easy-to-navigate mobile app, there's no time to reinvent the wheel. This concise book provides a handy reference to 70 mobile app design patterns, illustrated by more than 400 screenshots from current iOS, Android, BlackBerry, WebOS, Windows Mobile, and Symbian apps. User experience professional Theresa Neil (Designing Web Interfaces) walks you through design patterns in 10 separate categories, including anti-patterns. Whether you're designing a simple iPhone application or one that's meant to work for every popular mobile OS on the mark

Re-scan confocal microscopy: scanning twice for better resolution.

Science.gov (United States)

De Luca, Giulia M R; Breedijk, Ronald M P; Brandt, Rick A J; Zeelenberg, Christiaan H C; de Jong, Babette E; Timmermans, Wendy; Azar, Leila Nahidi; Hoebe, Ron A; Stallinga, Sjoerd; Manders, Erik M M

2013-01-01

We present a new super-resolution technique, Re-scan Confocal Microscopy (RCM), based on standard confocal microscopy extended with an optical (re-scanning) unit that projects the image directly on a CCD-camera. This new microscope has improved lateral resolution and strongly improved sensitivity while maintaining the sectioning capability of a standard confocal microscope. This simple technology is typically useful for biological applications where the combination high-resolution and high-sensitivity is required.

Invest in your data: how clinical mobility solutions liberate data and drive cost savings.

Science.gov (United States)

Luo, Si

2016-02-01

Smart point-of-care mobile solutions integrate with a health system's existing communications and IT infrastructure to achieve the following benefits: Unify data management and communication functions using a single device. Improve accuracy of data collection, medication administration, and blood collection through scanning and cross-matching. Facilitate data accessibility from electronic health records and clinical protocols. Enable better care-team communication while safeguarding personal health information. Increase accuracy and efficiency, thereby improving performance and satisfaction scores.

Mobile Lexicography

DEFF Research Database (Denmark)

Køhler Simonsen, Henrik

2015-01-01

are already mobile – but lexicography is not yet fully ready for the mobile challenge, mobile users and mobile user situations. The article is based on empirical data from two surveys comprising 10 medical doctors, who were asked to look up five medical substances with the medical dictionary app Medicin.......dk and five students, who were asked to look up five terms with the dictionary app Gyldendal Engelsk-Dansk. The empirical data comprise approximately 15 hours of recordings of user behavior, think-aloud data and interview data. The data indicate that there is still much to be done in this area...... and that lexicographic innovation is needed. A new type of users, new user situations and new access methods call for new lexicographic solutions, and this article proposes a six-pointed hexagram model, which can be used during dictionary app design to lexicographically calibrate the six dimensions in mobile...

Laser Scanning in Forests

Directory of Open Access Journals (Sweden)

Håkan Olsson

2012-09-01

Full Text Available The introduction of Airborne Laser Scanning (ALS to forests has been revolutionary during the last decade. This development was facilitated by combining earlier ranging lidar discoveries [1–5], with experience obtained from full-waveform ranging radar [6,7] to new airborne laser scanning systems which had components such as a GNSS receiver (Global Navigation Satellite System, IMU (Inertial Measurement Unit and a scanning mechanism. Since the first commercial ALS in 1994, new ALS-based forest inventory approaches have been reported feasible for operational activities [8–12]. ALS is currently operationally applied for stand level forest inventories, for example, in Nordic countries. In Finland alone, the adoption of ALS for forest data collection has led to an annual savings of around 20 M€/year, and the work is mainly done by companies instead of governmental organizations. In spite of the long implementation times and there being a limited tradition of making changes in the forest sector, laser scanning was commercially and operationally applied after about only one decade of research. When analyzing high-ranked journal papers from ISI Web of Science, the topic of laser scanning of forests has been the driving force for the whole laser scanning research society over the last decade. Thus, the topic “laser scanning in forests” has provided a significant industrial, societal and scientific impact. [...

The Mobile Application Social Mode of Manufacturing Enterprise under the Environment of Mobile Internet

Directory of Open Access Journals (Sweden)

Zuo Cen

2017-01-01

Full Text Available The rapid development of the mobile internet, mobile communication technology and mobile terminal stimulate demand of mobile application in manufacturing enterprises, which makes the enterprise implement the mobile ERP. The implementation of mobile ERP changes the internal application management of manufacturing enterprises to social applications. We analyse the driving factors of implementing the mobile application social mode considering the complexity of organization relations and business processes of manufacturing enterprise. And then the mobile application social mode of the manufacturing enterprise is built based on mobile internet. Finally, we present the management strategies of the mobile application social network to provide references for the manufacturing enterprise.

Scanning Cloud Radar Observations at Azores: Preliminary 3D Cloud Products

Energy Technology Data Exchange (ETDEWEB)

Kollias, P.; Johnson, K.; Jo, I.; Tatarevic, A.; Giangrande, S.; Widener, K.; Bharadwaj, N.; Mead, J.

2010-03-15

The deployment of the Scanning W-Band ARM Cloud Radar (SWACR) during the AMF campaign at Azores signals the first deployment of an ARM Facility-owned scanning cloud radar and offers a prelude for the type of 3D cloud observations that ARM will have the capability to provide at all the ARM Climate Research Facility sites by the end of 2010. The primary objective of the deployment of Scanning ARM Cloud Radars (SACRs) at the ARM Facility sites is to map continuously (operationally) the 3D structure of clouds and shallow precipitation and to provide 3D microphysical and dynamical retrievals for cloud life cycle and cloud-scale process studies. This is a challenging task, never attempted before, and requires significant research and development efforts in order to understand the radar's capabilities and limitations. At the same time, we need to look beyond the radar meteorology aspects of the challenge and ensure that the hardware and software capabilities of the new systems are utilized for the development of 3D data products that address the scientific needs of the new Atmospheric System Research (ASR) program. The SWACR observations at Azores provide a first look at such observations and the challenges associated with their analysis and interpretation. The set of scan strategies applied during the SWACR deployment and their merit is discussed. The scan strategies were adjusted for the detection of marine stratocumulus and shallow cumulus that were frequently observed at the Azores deployment. Quality control procedures for the radar reflectivity and Doppler products are presented. Finally, preliminary 3D-Active Remote Sensing of Cloud Locations (3D-ARSCL) products on a regular grid will be presented, and the challenges associated with their development discussed. In addition to data from the Azores deployment, limited data from the follow-up deployment of the SWACR at the ARM SGP site will be presented. This effort provides a blueprint for the effort required

Defining energy vulnerability in mobility. Measuring energy vulnerability in mobility. Acting against energy vulnerability in mobility. Discussing energy vulnerability in mobility. Task no. 4

International Nuclear Information System (INIS)

Jouffe, Yves; Massot, Marie-Helene; Noble, Cyprien

2015-01-01

Extensive expansion of urban areas generates transportation needs and energy expenses for mobility. Households already impacted by fuel poverty also suffer from energy vulnerability in their mobility. This report was prepared in the framework of the study of fuel poverty in France in the light of several indicators from existing inquiries, databases and modeling tools. The report is organised in 4 parts dealing with: the definition of energy vulnerability in mobility, its measurement, the possible remedial actions, and the discussions about energy vulnerability in mobility through working group meetings, respectively

Mobile-bearing total knee arthroplasty: a full traumatic rotation of 180°.

Science.gov (United States)

Sudanese, Alessandra; Castiello, Emanuela; Affatato, Saverio

2013-06-25

From February 2008 to September 2012 we implanted 204 mobile-bearing knee prostheses in 192 patients. All the prostheses were cemented (both femoral and tibial components), and the patella was not replaced. Only one early complication of the implants (1/204 = 0.004%) occurred after a traumatic event as a full 180° rotation of the mobile-bearing polyethylene insert. A 78-year-old woman presented with swelling and severe pain at her right knee. This traumatic event was the only case among our mobile-bearing insert patients. 
The failed polyethylene inserts were retrieved and studied using a scanning electron microscope (SEM, ZEISS EVO 50 EP, Cambridge, UK) operating at 20 kV. 
Scratching and pitting were found on the UHMWPE insert perpendicular to the machining tracks for the concave surface. SEM micrographs of the insert showed burnishing on the concave surfaces and longitudinal scratches were clearly detectable and well-marked on the analyzed surfaces. 
A traumatic, fully rotating, polyethylene insert is rare and our case is the first report describing a traumatic event with a complete 180 degree rotation mobile-bearing in a total knee prosthesis. 
In the literature few reports discuss clinical outcomes after total knee arthroplasty in patients with Parkinson's disease and they cite mixed results. However, some authors suggest that posterior-stabilized and cruciate-retaining TKA should work well while others prefer cruciate-retaining, condylar constrained kinetics, or hinged devices. Although we did not implant a posterior-stabilized mobile-bearing total knee prosthesis or a constrained prosthesis, we obtained good clinical and radiological results at the 2-year followup.

Mobile Search and Advertising

OpenAIRE

Lovitskii, Vladimir; McCaffery, Colin; Thrasher, Michael; Traynor, David; Wright, Peter

2009-01-01

Mobile advertising is a rapidly growing sector providing brands and marketing agencies the opportunity to connect with consumers beyond traditional and digital media and instead communicate directly on their mobile phones. Mobile advertising will be intrinsically linked with mobile search, which has transported from the internet to the mobile and is identified as an area of potential growth. The result of mobile searching show that as a general rule such search result exceed 1...

Mobilities Design

DEFF Research Database (Denmark)

Jensen, Ole B.; Lanng, Ditte Bendix

2016-01-01

of life’ for billions of people in the everyday life. This paper is structured in three parts. After the general introduction we present the mobilities theory perspective of ‘staging mobilities’ and connects this to the empirical phenomenon of parking lots and their design. The paper ends in section three......Contemporary society is marked and defined by the ways in which mobile goods, bodies, vehicles, objects, and data are organized, moved and staged. On the backgound of the ‘mobilities turn’ (for short review paper on this see; Sheller 2011, Vannini 2010) this paper proposes a further development...... of the perspective in the direction of a material and design oriented turn. In order to fulfill this purpose we articulate a new and emerging research field, namely that of ‘mobilities design’. In our understanding time has come to articulate ‘Mobilities Design’ as a dedicated research field in and of its own...

Mobility Work

DEFF Research Database (Denmark)

Bardram, Jakob Eyvind; Bossen, Claus

2005-01-01

We posit the concept of Mobility Work to describe efforts of moving about people and things as part of accomplishing tasks. Mobility work can be seen as a spatial parallel to the concept of articulation work proposed by the sociologist Anselm Strauss. Articulation work describes efforts of coordi....../or resources. To accomplish their work, actors have to make the right configuration of these four aspects emerge.......We posit the concept of Mobility Work to describe efforts of moving about people and things as part of accomplishing tasks. Mobility work can be seen as a spatial parallel to the concept of articulation work proposed by the sociologist Anselm Strauss. Articulation work describes efforts...... of coordination necessary in cooperative work, but focuses, we argue, mainly on the temporal aspects of cooperative work. As a supplement, the concept of mobility work focuses on the spatial aspects of cooperative work. Whereas actors seek to diminish the amount of articulation work needed in collaboration...

Scanning WorldScan. Final report on the presentation and evaluation of WorldScan, a model of the WORLD economy for SCenario ANalysis

International Nuclear Information System (INIS)

Geurts, B.; Gielen, A.; Nahuis, R.; Tang, P.; Timmer, H.

1997-01-01

An overview is given of the efforts made to present and evaluate WorldScan, a long-term model of the world economy, developed at the Dutch Central Planning Bureau (CPB). One of the pivotal activities was the organisation of a peer review of the model during a two-day workshop. The reviewers were selected both from the academic and the policy field. The main recommendations of that review were (a) not to pursue a formal, full-scale linkage between WorldScan and the RIVM-developed climate model IMAGE. Instead, WorldScan should be used for separate economic analyses, which is input in the climate model; (b) to make more precise choices with respect to the underlying theories the time horizon of the analyses; (c) to improve the empirical base of WorldScan; and (d) to enhance the use of WorldScan for policy analyses on behalf of international policy fora. The review proved to be very beneficial for the evolution of WorldScan. Implementation of some of the recommendations has led to increased use of the model by international institutions. Since the review, WorldScan has been used on behalf of the European Union (EU), the Organisation for Economic Cooperation and Development (OECD), the Energy Modelling Forum (EMF), the Centre for Global Trade Analysis (GTAP), the Chinese Academy of Social Sciences (CASS) and Indian Planning Commission (IPC). 110 refs

Inferring Human Mobility from Sparse Low Accuracy Mobile Sensing Data

DEFF Research Database (Denmark)

Cuttone, Andrea; Jørgensen, Sune Lehmann; Larsen, Jakob Eg

2014-01-01

Understanding both collective and personal human mobility is a central topic in Computational Social Science. Smartphone sensing data is emerging as a promising source for studying human mobility. However, most literature focuses on high-precision GPS positioning and high-frequency sampling, which...... is not always feasible in a longitudinal study or for everyday applications because location sensing has a high battery cost. In this paper we study the feasibility of inferring human mobility from sparse, low accuracy mobile sensing data. We validate our results using participants' location diaries......, and analyze the inferred geographical networks, the time spent at different places, and the number of unique places over time. Our results suggest that low resolution data allows accurate inference of human mobility patterns....

Regulatory considerations in the licensing of a mobile backscatter X-ray device used in security screening

International Nuclear Information System (INIS)

Scott, Jim; Railey, Leon

2008-01-01

This paper describes the regulatory and radiation protection issues taken into consideration in the licensing of a mobile security screening device which employs backscatter X-ray technology. The views expressed are those of the authors and are not the formal view of ARPANSA. The US standard ANSI N43.17 proposes doses limits for X-ray personnel security screening systems, viz. 0.1 μSv effective dose per scan; 250 μSv effective dose per year. The Z backscatter van TM satisfies the first criterion, as demonstrated by the independent measurements. Finally, if we assume an average effective dose of 0.1 μSv per scan, an individual would require to be scanned approximately 7 times per day, every day for a year in order to exceed the second dose limit of 250 μSv per year. This is considered extremely unlikely, and hence the van also meets the requirements of ANSI N43.17.

Mobile microscopy as a screening tool for oral cancer in India: A pilot study.

Directory of Open Access Journals (Sweden)

Arunan Skandarajah

Full Text Available Oral cancer is the most common type of cancer among men in India and other countries in South Asia. Late diagnosis contributes significantly to this mortality, highlighting the need for effective and specific point-of-care diagnostic tools. The same regions with high prevalence of oral cancer have seen extensive growth in mobile phone infrastructure, which enables widespread access to telemedicine services. In this work, we describe the evaluation of an automated tablet-based mobile microscope as an adjunct for telemedicine-based oral cancer screening in India. Brush biopsy, a minimally invasive sampling technique was combined with a simplified staining protocol and a tablet-based mobile microscope to facilitate local collection of digital images and remote evaluation of the images by clinicians. The tablet-based mobile microscope (CellScope device combines an iPad Mini with collection optics, LED illumination and Bluetooth-controlled motors to scan a slide specimen and capture high-resolution images of stained brush biopsy samples. Researchers at the Mazumdar Shaw Medical Foundation (MSMF in Bangalore, India used the instrument to collect and send randomly selected images of each slide for telepathology review. Evaluation of the concordance between gold standard histology, conventional microscopy cytology, and remote pathologist review of the images was performed as part of a pilot study of mobile microscopy as a screening tool for oral cancer. Results indicated that the instrument successfully collected images of sufficient quality to enable remote diagnoses that show concordance with existing techniques. Further studies will evaluate the effectiveness of oral cancer screening with mobile microscopy by minimally trained technicians in low-resource settings.

Advertising on mobile applications

OpenAIRE

Sobolevsky, Alexandr

2015-01-01

The article analyzes the new method of mobile advertising. Advertising in mobile applications - a subspecies of mobile marketing, where advertising is distributed using mobile phones and smartphones. Ad placement is going on inside of applications and games for smartphones. It has a high potential due to the large number of mobile phone users (over 6.5 billion in 2013).

Mobility Balance Sheet 2009

International Nuclear Information System (INIS)

Jorritsma, P.; Derriks, H.; Francke, J.; Gordijn, H.; Groot, W.; Harms, L.; Van der Loop, H.; Peer, S.; Savelberg, F.; Wouters, P.

2009-06-01

The Mobility Balance Sheet provides an overview of the state of the art of mobility in the Netherlands. In addition to describing the development of mobility this report also provides explanations for the growth of passenger and freight transport. Moreover, the Mobility Balance Sheet also focuses on a topical theme: the effects of economic crises on mobility. [nl

Codification of scan path parameters and development of perimeter scan strategies for 3D bowl-shaped laser forming

Science.gov (United States)

Tavakoli, A.; Naeini, H. Moslemi; Roohi, Amir H.; Gollo, M. Hoseinpour; Shahabad, Sh. Imani

2018-01-01

In the 3D laser forming process, developing an appropriate laser scan pattern for producing specimens with high quality and uniformity is critical. This study presents certain principles for developing scan paths. Seven scan path parameters are considered, including: (1) combined linear or curved path; (2) type of combined linear path; (3) order of scan sequences; (4) the position of the start point in each scan; (5) continuous or discontinuous scan path; (6) direction of scan path; and (7) angular arrangement of combined linear scan paths. Regarding these path parameters, ten combined linear scan patterns are presented. Numerical simulations show continuous hexagonal, scan pattern, scanning from outer to inner path, is the optimized. In addition, it is observed the position of the start point and the angular arrangement of scan paths is the most effective path parameters. Also, further experimentations show four sequences due to creat symmetric condition enhance the height of the bowl-shaped products and uniformity. Finally, the optimized hexagonal pattern was compared with the similar circular one. In the hexagonal scan path, distortion value and standard deviation rather to edge height of formed specimen is very low, and the edge height despite of decreasing length of scan path increases significantly compared to the circular scan path. As a result, four-sequence hexagonal scan pattern is proposed as the optimized perimeter scan path to produce bowl-shaped product.

Trends in Mobile Marketing

OpenAIRE

Chocholová, Petra

2010-01-01

The principal aim of this thesis is to assess the state of the mobile marketing as of the first quarter of 2011 and to discuss various scenarios of the future development. This thesis defines the terms "mobile marketing" and "mobile advertising" and identifies the main players in the industry. It explores the main categories of mobile advertising such as mobile messaging, in-content and mobile internet advertising. Later, it analyzes the latest trends in the industry and describes in detail t...

Mobile financial services and financial inclusion: Is it a boon for savings mobilization?

Directory of Open Access Journals (Sweden)

Shem Alfred Ouma

2017-06-01

Full Text Available The adoption of mobile telephony to provide financial services in Africa has become instrumental in integrating the hitherto unbanked segments of the population to the mainstream financial systems. This study sought to establish this linkage by examining whether the pervasive use of mobile telephony to provide financial services is a boon for savings mobilization in selected countries in sub Saharan Africa. The findings show that availability and usage of mobile phones to provide financial services promotes the likelihood of saving at the household level. Not only does access to mobile financial services boost the likelihood to save, but also has a significant impact on the amounts saved, perhaps due to the frequency and convenience with which such transactions can be undertaken using a mobile phone. Both forms of savings, that is, basic mobile phone savings stored in the phone and bank integrated mobile savings are likely to be promoted by use of mobile phones. Thus, growing and deepening the scope for mobile phone financial services is an avenue for promoting savings mobilization, especially among the poor and low income groups with constrained access to formal financial services.

Making Everyday Mobility

DEFF Research Database (Denmark)

Wind, Simon

2013; Urry 2007) and family theory (Holdsworth 2013; Morgan 2011), it is argued that family mobility is far from only an instrumental phenomenon, displacing family members back and forth between activities and doings, but also a type of family practice (Morgan, 2011) carrying social and emotional...... coping process in the family, it is argued that making and performing mobility practices is to be understood as creating elasticity. Following this, it is elasticity that enables family members to stretch to accommodate the family’s practical, social and emotional conditions as well as adapt......Based upon a qualitative PhD study of 11 families everyday mobility, this paper inquiries into the everyday mobility of families with children in the Greater Copenhagen Area and the role mobility plays in contributing to coping in the families’ everyday life. Drawing on Mobilities theory (Jensen...

Mobiles Robotersystem

OpenAIRE

Schmierer, G.; Wolf, A.

1999-01-01

DE 19816893 A UPAB: 20000203 NOVELTY - An optical and or acoustic noticeable advertising and or information carrier (10) is fixed permitting detachment in such a manner at the mobile platform (8), that the advertising and or information carrier does not impair the movability of the mobile platform. The advertising is provided at an exposed place on the mobile platform. USE - Advertising or information communication. ADVANTAGE - Advertising or information is imparted in prominent positioning w...

Consumers’ Attitudes Towards Mobile Marketing and Mobile Commerce in Consumer Markets

OpenAIRE

Suleyman Barutcu

2008-01-01

Advances in information and communication technologies are not only offering new marketing channels to companies but also significantly influencing the ways in which companies conduct their businesses and marketing activities. This paper analyses the possible significant impacts of mobile phone technology developments on marketing, and offers insights into mobile commerce and mobile marketing, which have not previously been investigated in Turkey. In the survey, mobile phone users' attitudes ...

Scanning tunneling microscopy III theory of STM and related scanning probe methods

CERN Document Server

Güntherodt, Hans-Joachim

1996-01-01

Scanning Tunneling Microscopy III provides a unique introduction to the theoretical foundations of scanning tunneling microscopy and related scanning probe methods. The different theoretical concepts developed in the past are outlined, and the implications of the theoretical results for the interpretation of experimental data are discussed in detail. Therefore, this book serves as a most useful guide for experimentalists as well as for theoreticians working in the filed of local probe methods. In this second edition the text has been updated and new methods are discussed.

Scanning device for a spectrometer

International Nuclear Information System (INIS)

Ignat'ev, V.M.

1982-01-01

The invention belongs to scanning devices and is intended for spectrum scanning in spectral devices. The purpose of the invention is broadening of spectral scanning range. The device construction ensures the spectrum scanning range determined from revolution fractions to several revolutions of the monochromator drum head, any number of the drum head revolutions determined by integral number with addition of the drum revolution fractions with high degree of accuracy being possible

The African Mobile Story

DEFF Research Database (Denmark)

This book identifies the factors that has enabled the growth of mobile telephony in Africa. The book covers the regulatory factors, the development and usage of mobile application, mobile security and sustainable power source for mobile networks...

Close-range laser scanning in forests: towards physically based semantics across scales.

Science.gov (United States)

Morsdorf, F; Kükenbrink, D; Schneider, F D; Abegg, M; Schaepman, M E

2018-04-06

Laser scanning with its unique measurement concept holds the potential to revolutionize the way we assess and quantify three-dimensional vegetation structure. Modern laser systems used at close range, be it on terrestrial, mobile or unmanned aerial platforms, provide dense and accurate three-dimensional data whose information just waits to be harvested. However, the transformation of such data to information is not as straightforward as for airborne and space-borne approaches, where typically empirical models are built using ground truth of target variables. Simpler variables, such as diameter at breast height, can be readily derived and validated. More complex variables, e.g. leaf area index, need a thorough understanding and consideration of the physical particularities of the measurement process and semantic labelling of the point cloud. Quantified structural models provide a framework for such labelling by deriving stem and branch architecture, a basis for many of the more complex structural variables. The physical information of the laser scanning process is still underused and we show how it could play a vital role in conjunction with three-dimensional radiative transfer models to shape the information retrieval methods of the future. Using such a combined forward and physically based approach will make methods robust and transferable. In addition, it avoids replacing observer bias from field inventories with instrument bias from different laser instruments. Still, an intensive dialogue with the users of the derived information is mandatory to potentially re-design structural concepts and variables so that they profit most of the rich data that close-range laser scanning provides.

Development and optimization of thermographic techniques for Non-Destructive Evaluation of multilayered structures

Science.gov (United States)

Gavrilov, Dmitry J.

Quality control of modern materials is of the utmost importance in science and industry. Methods for nondestructive evaluation of material properties and the presence of defects are numerous. They differ in terms of their sensitivity and applicability in various conditions, and they provide different kinds of data such as the speed of sound in the material, its hardness, radiation absorption, etc. Based on measured characteristics an analyst makes a decision on the material studied. This work addresses a class of methods known as active thermographic analysis. Thermography analyzes the temperature of the surface of the sample under different external conditions. By keeping track of temperature changes at the surface caused by a deposition of heat on the sample one can determine its material properties such as theand processing the data captured it is possible to make decisions on parameters of this sample. Among the data which can be acquired are such important information as the location of internal defects (e.g., detachments, hollows, inclusions), thickness of the material layers, thermal parameters of the material and the location of internal defects (e.g., detachments, hollows, inclusions). The first part of this research investigates a method for analysis of layered composite materials using the approach based on interference of so called temperature waves. As demonstrated using the expressions derived, one can determine the thermal properties of the layers of the sample by applying a harmonically modulated heat flux to the surfaces and measuring the phase of the periodically changing surface temperature. This approach can be of use in the field of designing and analysis of composite thermal insulation coatings. In the second part of this work a method of analyzing objects of fine art was investigated, particularly - detection of subsurface defects. In the process of preserving art it is of primary importance to determine whether restoration is necessary

Preoperative bone scans

International Nuclear Information System (INIS)

Charkes, N.D.; Malmud, L.S.; Caswell, T.; Goldman, L.; Hall, J.; Lauby, V.; Lightfoot, W.; Maier, W.; Rosemond, G.

1975-01-01

Strontium nitrate Sr-87m bone scans were made preoperatively in a group of women with suspected breast cancer, 35 of whom subsequently underwent radical mastectomy. In 3 of the 35 (9 percent), the scans were abnormal despite the absence of clinical or roentgenographic evidence of metastatic disease. All three patients had extensive axillary lymph node involvement by tumor, and went on to have additional bone metastases, from which one died. Roentgenograms failed to detect the metastases in all three. Occult bone metastases account in part for the failure of radical mastectomy to cure some patients with breast cancer. It is recommended that all candidates for radical mastectomy have a preoperative bone scan. (U.S.)

Ion mobility spectrometry

CERN Document Server

Eiceman, GA

2005-01-01

Key Developments for Faster, More Precise Detection Capabilities Driven by the demand for the rapid and advanced detection of explosives, chemical and biological warfare agents, and narcotics, ion mobility spectrometry (IMS) undergone significant refinements in technology, computational capabilities, and understanding of the principles of gas phase ion chemistry and mobility. Beginning with a thorough discussion of the fundamental theories and physics of ion mobility, Ion Mobility Spectrometry, Second Edition describes the recent advances in instrumentation and newly

Bone scan in pediatrics

International Nuclear Information System (INIS)

Gordon, I.; Peters, A.M.

1987-01-01

In 1984, a survey carried out in 21 countries in Europe showed that bone scintigraphy comprised 16% of all paediatric radioisotope scans. Although the value of bone scans in paediatrics is potentially great, their quality varies greatly, and poor-quality images are giving this valuable technique a bad reputation. The handling of children requires a sensitive staff and the provision of a few simple inexpensive items of distraction. Attempting simply to scan a child between two adult patients in a busy general department is a recipe for an unhappy, uncooperative child with the probable result of poor images. The intravenous injection of isotope should be given adjacent to the gamma camera room, unless dynamic scans are required, so that the child does not associate the camera with the injection. This injection is best carried out by someone competent in paediatric venipunture; the entire procedure should be explained to the child and parent, who should remain with child throughout. It is naive to think that silence makes for a cooperative child. The sensitivity of bone-seeking radioisotope tracers and the marked improvement in gamma camera resolution has allowed the bone scanning to become an integrated technique in the assessment of children suspected of suffering from pathological bone conditions. The tracer most commonly used for routine bone scanning is 99m Tc diphosphonate (MDP); other isotopes used include 99m Tc colloid for bone marrow scans and 67 Ga citrate and 111 In white blood cells ( 111 In WBC) for investigation of inflammatory/infective lesions

Mobile Advertising : A Case study of Mobile advertising Solutions

OpenAIRE

Salim, Ali; Alikhani, Nima

2009-01-01

This report has been produced as a result of a Thesis assignment conducted at Ericsson. Itspurpose is to give an overview of the Mobile Advertising industry. In this report an overviewof mobile advertising is presented and thru which channels advertising could be used. Thenthree mobile advertising campaigns are shown and described with background, strategy andresults. The different global markets, the different actors in the value chain and how the onlinebehavior has changed are analyzed. The...

MOBILE ADVERTISING EFFECT: INVESTIGATING FACTORS AFFECTING THE USAGE OF MOBILE PAYMENT

OpenAIRE

Ho, Ching-Wei; Wang, Yu-Bing; Fang, Chun Hao

2017-01-01

Purpose- The purpose of this study is tobuild a set of hypotheses and a novel conceptual model around the adoption ofmobile payment. In brief, it is to discuss how mobile advertisement effectaffects the intention to use the mobile payment. Methodology- The study aims to apply a partialleast squares (PLS) path modeling technique to demonstrate exploring therelationship between mobile trust and involvement along with customers’ attitudeand mobile payment intention. Findings- The findings reveal...

The utility of repeat sestamibi scans in patients with primary hyperparathyroidism after an initial negative scan.

Science.gov (United States)

Krishnamurthy, Vikram D; Sound, Sara; Okoh, Alexis K; Yazici, Pinar; Yigitbas, Hakan; Neumann, Donald; Doshi, Krupa; Berber, Eren

2017-06-01

We analyzed the utility of repeated sestambi scans in patients with primary hyperparathyroidism and its effects on operative referral. We carried out a retrospective review of patients with primary hyperparathyroidism who underwent repeated sestambi scans exclusively within our health system between 1996-2015. Patient demographic, presentation, laboratory, imaging, operative, and pathologic data were reviewed. Univariate analysis with JMP Pro v12 was used to identify factors associated with conversion from an initial negative to a subsequent positive scan. After exclusion criteria (including reoperations), we identified 49 patients in whom 59% (n = 29) of subsequent scans remained negative and 41% (n = 20) converted to positive. Factors associated with an initial negative to a subsequent positive scan included classic presentation and second scans with iodine subtraction (P = .04). Nonsurgeons were less likely to order an iodine-subtraction scan (P < .05). Fewer patients with negative imaging were referred to surgery (33% vs 100%, P = .005), and median time to operation after the first negative scan was 25 months (range 1.4-119). Surgeon-performed ultrasonography had greater sensitivity and positive predictive value than repeated sestamibi scans. Negative sestambi scans decreased and delayed operative referral. Consequently, we identified several process improvement initiatives, including education regarding superior institutional imaging. Combining all findings, we created an algorithm for evaluating patients with primary hyperparathyroidism after initially negative sestamibi scans, which incorporates surgeon-performed ultrasonography. Copyright © 2016 Elsevier Inc. All rights reserved.

Bone scan and red blood cell scan in a patient with epidermal naevus syndrome

International Nuclear Information System (INIS)

Becker, W.; Wolf, F.; Stosiek, N.; Peters, K.P.

1990-01-01

A bone scan and red blood cell scan in the rare epidermal naevus syndrome, associated with multiple haemangiomes of the bone and hypophosphataemic osteomalacia in a 20-year-old man are reported. The typical pattern of osteomalacia on the bone scan was associated with lesions of increased bone metabolism in the peripheral bones. The haemangiomas did not pool labelled red blood cells. Thus, the bone scan seems to be suited for diagnosing the complete extent of haemangiomas in bone, but they could not be specifically proven by red blood cell pooling. (orig.)

A thermographic study on eyes affected by Age-related Macular Degeneration: Comparison among various forms of the pathology and analysis of risk factors

Science.gov (United States)

Matteoli, Sara; Finocchio, Lucia; Biagini, Ilaria; Giacomelli, Giovanni; Sodi, Andrea; Corvi, Andrea; Virgili, Gianni; Rizzo, Stanislao

2016-05-01

The aims of this study are to investigate (1) the ocular thermographic profiles in eyes affected by Age related Macular Degeneration (AMD) and age-matched controls to detect possible hemodynamic abnormalities that could be involved in the pathogenesis of the disease, (2) whether any risk factors associated with the disease could affect the development of a form of AMD rather than another. Thirty-four eyes with Age-Related Maculopathy (ARM), 41 eyes with dry AMD, 60 eyes affected by wet AMD, and 74 eyes with fibrotic AMD were included in the study. The control group consisted of 48 healthy eyes. Exclusion criteria were represented by any other ocular diseases other than AMD, tear film abnormalities, systemic cardiovascular abnormalities, systemic diseases and a body temperature higher than 37.5 °C. A total of 210 eyes without pupil dilation were investigated by infrared thermography (FLIR A320). The Ocular Surface Temperature (OST) of five ocular areas was calculated by means of an image processing technique from the infrared images. Two-sample t-test, one-way ANOVA test and multivariate analysis were used for statistical analyses. ANOVA analyses showed no significant differences among AMD groups (P-value > 0.05), however, OST in AMD patients was significantly lower than in controls (P-value < 0.0001). Smokers showed higher possibility (P-value = 0.012) of developing wet AMD instead of dry AMD. Infrared thermography may be a helpful, non-invasive and not time-consuming method to be used in the management of patients with this common degenerative maculopathy.

Internal scanning method as unique imaging method of optical vortex scanning microscope

Science.gov (United States)

Popiołek-Masajada, Agnieszka; Masajada, Jan; Szatkowski, Mateusz

2018-06-01

The internal scanning method is specific for the optical vortex microscope. It allows to move the vortex point inside the focused vortex beam with nanometer resolution while the whole beam stays in place. Thus the sample illuminated by the focused vortex beam can be scanned just by the vortex point. We show that this method enables high resolution imaging. The paper presents the preliminary experimental results obtained with the first basic image recovery procedure. A prospect of developing more powerful tools for topography recovery with the optical vortex scanning microscope is discussed shortly.

Special report: workshop on 4D-treatment planning in actively scanned particle therapy--recommendations, technical challenges, and future research directions.

Science.gov (United States)

Knopf, Antje; Bert, Christoph; Heath, Emily; Nill, Simeon; Kraus, Kim; Richter, Daniel; Hug, Eugen; Pedroni, Eros; Safai, Sairos; Albertini, Francesca; Zenklusen, Silvan; Boye, Dirk; Söhn, Matthias; Soukup, Martin; Sobotta, Benjamin; Lomax, Antony

2010-09-01

This article reports on a 4D-treatment planning workshop (4DTPW), held on 7-8 December 2009 at the Paul Scherrer Institut (PSI) in Villigen, Switzerland. The participants were all members of institutions actively involved in particle therapy delivery and research. The purpose of the 4DTPW was to discuss current approaches, challenges, and future research directions in 4D-treatment planning in the context of actively scanned particle radiotherapy. Key aspects were addressed in plenary sessions, in which leaders of the field summarized the state-of-the-art. Each plenary session was followed by an extensive discussion. As a result, this article presents a summary of recommendations for the treatment of mobile targets (intrafractional changes) with actively scanned particles and a list of requirements to elaborate and apply these guidelines clinically.

Development of a sealed source radiation detector system for gamma ray scanning of petroleum distillation columns

International Nuclear Information System (INIS)

Vasquez Salvador, Pablo Antonio

2004-01-01

Gamma Ray Scanning is an online technique to 'view' the hydraulic performance of an operating column, with no disruption to operating processes conditions (pressure and temperature), as a cost-effective solution. The principle of this methodology consists of a small suitably sealed gamma radiation source and a radiation detector experimentally positioned to the column, moving concurrently in small increments on opposite sides and the quantity of gamma transmitted. The source-detector system consists of: a sealed ''6 0 Co radioactive source in a panoramic lead radiator, a scintillator detector coupled to a ratemeter / analyzer and a mobile system. In this work, a gamma scanning sealed source-detector system for distillation columns, was developed, comparing two scintillator detectors: NaI(Tl) (commercial) and CsI(Tl) (IPEN). In order to project the system, a simulated model of a tray-type distillation column was used. The equipment developed was tested in an industrial column for water treatment (6.5 m diameter and 40 m height). The required activities of 6 ''0Co, laboratory (11.1 MBq) and industrial works (1.48 TBq) were calculated by simulation software. Both, the NaI(Tl) and the CsI(Tl) detectors showed good proprieties for gamma scanning applications, determining the position and presence or absence of trays. (author)

Classification and Evaluation of Mobility Metrics for Mobility Model Movement Patterns in Mobile Ad-Hoc Networks

OpenAIRE

Santosh Kumar S C Sharma Bhupendra Suman

2011-01-01

A mobile ad hoc network is collection of self configuring and adaption of wireless link between communicating devices (mobile devices) to form an arbitrary topology and multihop wireless connectivity without the use of existing infrastructure. It requires efficient dynamic routing protocol to determine the routes subsequent to a set of rules that enables two or more devices to communicate with each others. This paper basically classifies and evaluates the mobility metrics into two categories-...

Mobility Charters and Manifestos

DEFF Research Database (Denmark)

Jensen, Ole B.

2010-01-01

This paper explore a number of different cases of articulating notions of ‘correct’ mobility behavior and practice by looking into charters, manifestos and codes of mobility regulation. Within such discourses of ‘correct mobility’ more or less subtle expressions of power as well as normative and ...... ‘Highway Code Booklets’ from the 1930’s, 40’s and 50’s, the ‘City Slow Charter’, the ‘New Urbanism Charter’ as attempts to codify and order mobility and mobile practices.......This paper explore a number of different cases of articulating notions of ‘correct’ mobility behavior and practice by looking into charters, manifestos and codes of mobility regulation. Within such discourses of ‘correct mobility’ more or less subtle expressions of power as well as normative...... and ethical positions on mobility prevail. Such ‘imagined correct mobility behavior’ are drawing on larger issues of societal change that need to be brought out in a critical analysis and discussion reflecting the attempts to control, design and orchestrate mobility patterns. The paper therefore argues within...

Mobile code security

Science.gov (United States)

Ramalingam, Srikumar

2001-11-01

A highly secure mobile agent system is very important for a mobile computing environment. The security issues in mobile agent system comprise protecting mobile hosts from malicious agents, protecting agents from other malicious agents, protecting hosts from other malicious hosts and protecting agents from malicious hosts. Using traditional security mechanisms the first three security problems can be solved. Apart from using trusted hardware, very few approaches exist to protect mobile code from malicious hosts. Some of the approaches to solve this problem are the use of trusted computing, computing with encrypted function, steganography, cryptographic traces, Seal Calculas, etc. This paper focuses on the simulation of some of these existing techniques in the designed mobile language. Some new approaches to solve malicious network problem and agent tampering problem are developed using public key encryption system and steganographic concepts. The approaches are based on encrypting and hiding the partial solutions of the mobile agents. The partial results are stored and the address of the storage is destroyed as the agent moves from one host to another host. This allows only the originator to make use of the partial results. Through these approaches some of the existing problems are solved.

External Second Gate, Fourier Transform Ion Mobility Spectrometry: Parametric Optimization for Detection of Weapons of Mass Destruction

Directory of Open Access Journals (Sweden)

Edward E. Tarver

2004-03-01

Full Text Available Abstract: Ion mobility spectrometry (IMS is recognized as one of the most sensitive and robust techniques for the detection of narcotics, explosives and chemical warfare agents. IMS is widely used in forensic, military and security applications. Increasing threat of terrorist attacks, the proliferation of narcotics, Chemical Weapons Convention (CWC treaty verification as well as humanitarian de-mining efforts have mandated that equal importance be placed on the time required to obtain results as well as the quality of the analytical data. [1] In this regard IMS is virtually unrivaled when both speed of response and sensitivity have to be considered. [2] The problem with conventional (signal averaging IMS systems is the fixed duty cycle of the entrance gate that restricts to less than 1%, the number of available ions contributing to the measured signal. Furthermore, the signal averaging process incorporates scan-to-scan variations that degrade the spectral resolution contributing to misidentifications and false positives. With external second gate, Fourier Transform ion mobility spectrometry (FT-IMS the entrance gate frequency is variable and can be altered in conjunction with other data acquisition parameters (scan time and sampling rate to increase the spectral resolution to reduce false alarms and improve the sensitivity for early warning and contamination avoidance. In addition, with FT-IMS the entrance gate operates with a 50% duty cycle and so affords a seven-fold increase in sensitivity. Recent data on high explosives are presented to demonstrate the parametric optimization in sensitivity and resolution of our system.

MobilED – a mobile tools and services platform for formal and informal learning

CSIR Research Space (South Africa)

Ford, M

2006-10-01

Full Text Available and language technologies (voice, text, images) are used via the mobile phone as tools in the learning process. The first 2 pilots focused on the use of low-cost mobile phones, which are readily available in the developing world. It consisted of the development...

Playful Mobility Choices: Motivating informed mobility decision making by applying game mechanics

Directory of Open Access Journals (Sweden)

A. Millonig

2014-10-01

Full Text Available Motivating people to change their mobility behaviour patterns towards more sustainable forms of mobility is one of the major challenges regarding climate change and quality of life. Recently, an increasing amount of attempts to use gamification for triggering such behavioural changes can be observed. However, little is known about the actual impact of using game elements. This contribution describes a concept for systematically analysing the group-specific effects of different game mechanics on mobility decision processes (e.g. mode and route choice. Based on theoretical findings concerning player types and mobility styles we developed a framework for identifying effective game mechanics motivating users to explore mobility alternatives and take more informed and more sustainable mode or route choice decisions. The results will form the basis for implementing game mechanics in mobility information services motivating users to explore unfamiliar but more sustainable mobility options.

CERN Mobility Survey

CERN Multimedia

GS Department

2011-01-01

The Institute of Shipping and Transport of the University of the Aegean and the National Technical University of Athens are partners with CERN in a study of mobility patterns between and within the CERN sites and to that effect have realized a mobility survey dedicated to the CERN community.         The study aims to understand: How you presently get around the CERN sites; What problems you encounter regarding mobility; What your needs are; What improvements you’d like to see; What measures you would like to see implemented most. The replies we receive will enable us to define a general policy promoting the diversity of mobility at CERN and to establish and quantify the strategic actions to be implemented for both the short and medium term. The objectives of the transport mobility plans are to: Facilitate mobility within and between the CERN sites by identifying adequate solutions in response to individual ...

MOBILE-izing Adolescent Sexual and Reproductive Health Care: A Pilot Study Using a Mobile Health Unit in Chicago.

Science.gov (United States)

Stefansson, Lilja S; Webb, M Elizabeth; Hebert, Luciana E; Masinter, Lisa; Gilliam, Melissa L

2018-03-01

Adolescents experience numerous barriers to obtaining sexual and reproductive health care (SRHC). Mobile Health Units (MHUs) can remove some barriers by traveling to the community. This pilot study developed Mobile SRHC through an iterative process on an existing MHU and evaluated it among adolescents and providers. Mobile SRHC was developed through a mixed-method, multiphase study. Three key informant interviews with MHU providers, an adolescent needs assessment survey, and a Youth Model Development Session informed model development. Emergency contraception (EC), oral contraceptive pills (OCPs), and depot-medroxyprogesterone acetate (DMPA) were sequentially incorporated into MHU services. Administrative data assessed method distribution and surveys assessed patient satisfaction. Key informants held positive attitudes toward implementing Mobile SRHC into their practice. Needs assessment surveys (N = 103) indicated a majority was interested in learning about sexual health (66.0%) and obtaining birth control (54.4%) on an MHU. Over 3 months, 123 adolescents participated in Mobile SRHC. Seven packs and 9 prescriptions of EC, 8 3-month packs and 10 prescriptions of OCPs, and 5 injections and 5 prescriptions of DMPA were distributed. Ninety-two percent of adolescent participants reported they would recommend Mobile SRHC to friends. Mobile SRHC is a feasible approach for reproductive health care among adolescents. © 2018, American School Health Association.

Instant XenMobile MDM

CERN Document Server

Lakhani, Aamir

2013-01-01

Get to grips with a new technology, understand what it is and what it can do for you, and then get to work with the most important features and tasks. Written in a user friendly style, this guide will get readers up and running with XenMobile MDM.If you want to run your mobile enterprises on XenMobile, or work on a BYOD strategy within your organization, then this is the ideal book for you. XenMobile MDM comprehensively explores how to set up and use XenMobile to provision, secure, and manage mobile devices.

Head First Mobile Web

CERN Document Server

Gardner, Lyza; Grigsby, Jason

2011-01-01

Despite the huge number of mobile devices and apps in use today, your business still needs a website. You just need it to be mobile. Head First Mobile Web walks you through the process of making a conventional website work on a variety smartphones and tablets. Put your JavaScript, CSS media query, and HTML5 skills to work-then optimize your site to perform its best in the demanding mobile market. Along the way, you'll discover how to adapt your business strategy to target specific devices. Navigate the increasingly complex mobile landscapeTake both technical and strategic approaches to mobile

Mobile Portal Implementation Strategy

DEFF Research Database (Denmark)

Gao, Ping; Damsgaard, Jan

2005-01-01

Mobile portal plays an important role in mobile commerce market. Current literature focuses on static analysis on the value chain of mobile portals. This article provides a dynamic perspective on mobile portal strategy. Drawing upon network economics, we describe mobile portal implementation...... as a fourphase process. In different phase, a portal provider has various challenges to overcome and adopt diverse strategies, and correspondingly the regulator has different foci. The conceptual framework proposed in this article offers a basis for further analyses on the market dynamics of mobile commerce......, and can be generalized to studying other networked technologies...

Multi-Instrument Manager Tool for Data Acquisition and Merging of Optical and Electrical Mobility Size Distributions

International Nuclear Information System (INIS)

Tritscher, Torsten; Kykal, Carsten; Bischof, Oliver F; Koched, Amine; Filimundi, Eric; Han, Hee-Siew; Johnson, Tim; Elzey, Sherrie; Avenido, Aaron

2015-01-01

Electrical mobility classification (EC) followed by Condensation Particle Counter (CPC) detection is the technique combined in Scanning Mobility Particle Sizers(SMPS) to retrieve nanoparticle size distributions in the range from 2.5 nm to 1 μm. The detectable size range of SMPS systems can be extended by the addition of an Optical Particle Sizer(OPS) that covers larger sizes from 300 nm to 10 μm. This optical sizing method reports an optical equivalent diameter, which is often different from the electrical mobility diameter measured by the standard SMPS technique. Multi-Instrument Manager (MIM TM ) software developed by TSI incorporates algorithms that facilitate merging SMPS data sets with data based on optical equivalent diameter to compile single, wide-range size distributions. Here we present MIM 2.0, the next-generation of the data merging tool that offers many advanced features for data merging and post-processing. MIM 2.0 allows direct data acquisition with OPS and NanoScan SMPS instruments to retrieve real-time particle size distributions from 10 nm to 10 μm, which we show in a case study at a fireplace. The merged data can be adjusted using one of the merging options, which automatically determines an overall aerosol effective refractive index. As a result an indirect and average characterization of aerosol optical and shape properties is possible. The merging tool allows several pre-settings, data averaging and adjustments, as well as the export of data sets and fitted graphs. MIM 2.0 also features several post-processing options for SMPS data and differences can be visualized in a multi-peak sample over a narrow size range. (paper)

Mouse manipulation through single-switch scanning.

Science.gov (United States)

Blackstien-Adler, Susie; Shein, Fraser; Quintal, Janet; Birch, Shae; Weiss, Patrice L Tamar

2004-01-01

Given the current extensive reliance on the graphical user interface, independent access to computer software requires that users be able to manipulate a pointing device of some type (e.g., mouse, trackball) or be able to emulate a mouse by some other means (e.g., scanning). The purpose of the present study was to identify one or more optimal single-switch scanning mouse emulation strategies. Four alternative scanning strategies (continuous Cartesian, discrete Cartesian, rotational, and hybrid quadrant/continuous Cartesian) were selected for testing based on current market availability as well as on theoretical considerations of their potential speed and accuracy. Each strategy was evaluated using a repeated measures study design by means of a test program that permitted mouse emulation via any one of four scanning strategies in a motivating environment; response speed and accuracy could be automatically recorded and considered in view of the motor, cognitive, and perceptual demands of each scanning strategy. Ten individuals whose disabilities required them to operate a computer via single-switch scanning participated in the study. Results indicated that Cartesian scanning was the preferred and most effective scanning strategy. There were no significant differences between results from the Continuous Cartesian and Discrete Cartesian scanning strategies. Rotational scanning was quite slow with respect to the other strategies, although it was equally accurate. Hybrid Quadrant scanning improved access time but at the cost of fewer correct selections. These results demonstrated the importance of testing and comparing alternate single-switch scanning strategies.

Residential mobility : Towards progress in mobility health research

NARCIS (Netherlands)

Morris, T.; Manley, D.J.; Sabel, C.E.

2016-01-01

Research into health disparities has long recognized the importance of residential mobility as a crucial factor in determining health outcomes. However, a lack of connectivity between the health and mobility literatures has led to a stagnation of theory and application on the health side, which

Comparison of dimensional accuracy of digital dental models produced from scanned impressions and scanned stone casts

Science.gov (United States)

Subeihi, Haitham

Introduction: Digital models of dental arches play a more and more important role in dentistry. A digital dental model can be generated by directly scanning intraoral structures, by scanning a conventional impression of oral structures or by scanning a stone cast poured from the conventional impression. An accurate digital scan model is a fundamental part for the fabrication of dental restorations. Aims: 1. To compare the dimensional accuracy of digital dental models produced by scanning of impressions versus scanning of stone casts. 2. To compare the dimensional accuracy of digital dental models produced by scanning of impressions made of three different materials (polyvinyl siloxane, polyether or vinyl polyether silicone). Methods and Materials: This laboratory study included taking addition silicone, polyether and vinyl polyether silicone impressions from an epoxy reference model that was created from an original typodont. Teeth number 28 and 30 on the typodont with a missing tooth number 29 were prepared for a metal-ceramic three-unit fixed dental prosthesis with tooth #29 being a pontic. After tooth preparation, an epoxy resin reference model was fabricated by duplicating the typodont quadrant that included the tooth preparations. From this reference model 12 polyvinyl siloxane impressions, 12 polyether impressions and 12 vinyl polyether silicone impressions were made. All 36 impressions were scanned before pouring them with dental stone. The 36 dental stone casts were, in turn, scanned to produce digital models. A reference digital model was made by scanning the reference model. Six groups of digital models were produced. Three groups were made by scanning of the impressions obtained with the three different materials, the other three groups involved the scanning of the dental casts that resulted from pouring the impressions made with the three different materials. Groups of digital models were compared using Root Mean Squares (RMS) in terms of their

TH-CD-209-10: Scanning Proton Arc Therapy (SPArc) - The First Robust and Delivery-Efficient Spot Scanning Proton Arc Therapy

International Nuclear Information System (INIS)

Ding, X; Li, X; Zhang, J; Kabolizadeh, P; Stevens, C; Yan, D

2016-01-01

Purpose: To develop a delivery-efficient proton spot-scanning arc therapy technique with robust plan quality. Methods: We developed a Scanning Proton Arc(SPArc) optimization algorithm integrated with (1)Control point re-sampling by splitting control point into adjacent sub-control points; (2)Energy layer re-distribution by assigning the original energy layers to the new sub-control points; (3)Energy layer filtration by deleting low MU weighting energy layers; (4)Energy layer re-sampling by sampling additional layers to ensure the optimal solution. A bilateral head and neck oropharynx case and a non-mobile lung target case were tested. Plan quality and total estimated delivery time were compared to original robust optimized multi-field step-and-shoot arc plan without SPArc optimization (Arcmulti-field) and standard robust optimized Intensity Modulated Proton Therapy(IMPT) plans. Dose-Volume-Histograms (DVH) of target and Organ-at-Risks (OARs) were analyzed along with all worst case scenarios. Total delivery time was calculated based on the assumption of a 360 degree gantry room with 1 RPM rotation speed, 2ms spot switching time, beam current 1nA, minimum spot weighting 0.01 MU, energy-layer-switching-time (ELST) from 0.5 to 4s. Results: Compared to IMPT, SPArc delivered less integral dose(−14% lung and −8% oropharynx). For lung case, SPArc reduced 60% of skin max dose, 35% of rib max dose and 15% of lung mean dose. Conformity Index is improved from 7.6(IMPT) to 4.0(SPArc). Compared to Arcmulti-field, SPArc reduced number of energy layers by 61%(276 layers in lung) and 80%(1008 layers in oropharynx) while kept the same robust plan quality. With ELST from 0.5s to 4s, it reduced 55%–60% of Arcmulti-field delivery time for the lung case and 56%–67% for the oropharynx case. Conclusion: SPArc is the first robust and delivery-efficient proton spot-scanning arc therapy technique which could be implemented in routine clinic. For modern proton machine with ELST close

Factors influencing bone scan quality

International Nuclear Information System (INIS)

Adams, F.G.; Shirley, A.W.

1983-01-01

A reliable subjective method of assessing bone scan quality is described. A large number of variables which theoretically could influence scan quality were submitted to regression and factor analysis. Obesity, age, sex and abnormality of scan were found to be significant but weak variables. (orig.)

Children's velo-mobility

DEFF Research Database (Denmark)

Carstensen, Trine Agervig; Nielsen, Thomas Sick; Olafsson, Anton Stahl

2014-01-01

. How cycling is learned and constituted, and how cycling skills are consolidated, extended and turned into a stabilized practice remains unstudied. Drawing on in-depth interview data from the region of Copenhagen, Denmark, among families with children (N=20) the paper provides new insights into how......Sustainable mobilities play a dominate role in low carbon futures and cycling is an integral element. Children are heirs of transport cultures and crucial for future sustainable mobility. Moreover cycling is important for children’s independent mobility and geographical experience. Dominating...... approaches in transport research, including cycling, understand travel behaviour individualistic and lack to grasp the relational complexities, which are inevitable when considering children’s mobilities. Furthermore has children’s cycling largely been studied as independent mobility and active school travel...

Mobile Collocated Interactions

DEFF Research Database (Denmark)

Lucero, Andrés; Clawson, James; Lyons, Kent

2015-01-01

Mobile devices such as smartphones and tablets were originally conceived and have traditionally been utilized for individual use. Research on mobile collocated interactions has been looking at situations in which collocated users engage in collaborative activities using their mobile devices, thus...... going from personal/individual toward shared/multiuser experiences and interactions. However, computers are getting smaller, more powerful, and closer to our bodies. Therefore, mobile collocated interactions research, which originally looked at smartphones and tablets, will inevitably include ever......-smaller computers, ones that can be worn on our wrists or other parts of the body. The focus of this workshop is to bring together a community of researchers, designers and practitioners to explore the potential of extending mobile collocated interactions to the use of wearable devices....

Mobile Africa : an introduction

NARCIS (Netherlands)

Bruijn, de M.E.; Dijk, van R.A.; Foeken, D.W.J.

2001-01-01

The case studies in this book on mobility in sub-Saharan Africa critically discuss dichotomous interpretations of mobility and reject the idea that migration indicates a breakdown in society. They adopt the approach that sedentary and mobile worlds converge and that mobility is part of the

The de Morton Mobility Index: Normative Data for a Clinically Useful Mobility Instrument

Directory of Open Access Journals (Sweden)

E. M. Macri

2012-01-01

Full Text Available Determining mobility status is an important component of any health assessment for older adults. In order for a mobility measure to be relevant and meaningful, normative data are required for comparison to a healthy reference population. The DEMMI is the first mobility instrument to measure mobility across the spectrum from bed bound to functional levels of independent mobility. In this cross-sectional observational study, normative data were obtained for the DEMMI from a population of 183 healthy, community-dwelling adults age 60+ who resided in Vancouver, Canada and Melbourne, Australia. Older age categories had significantly lower DEMMI mobility mean scores (P<0.05, as did individuals who walked with a mobility aid or lived in semi-independent living (assisted living or retirement village, whereas DEMMI scores did not differ by sex (P=0.49 or reported falls history (P=0.21. Normative data for the DEMMI mobility instrument provides vital reference scores to facilitate its use across the mobility spectrum in clinical, research, and policymaking settings.

Ion mobility sensor system

Science.gov (United States)

Xu, Jun; Watson, David B.; Whitten, William B.

2013-01-22

An ion mobility sensor system including an ion mobility spectrometer and a differential mobility spectrometer coupled to the ion mobility spectrometer. The ion mobility spectrometer has a first chamber having first end and a second end extending along a first direction, and a first electrode system that generates a constant electric field parallel to the first direction. The differential mobility spectrometer includes a second chamber having a third end and a fourth end configured such that a fluid may flow in a second direction from the third end to the fourth end, and a second electrode system that generates an asymmetric electric field within an interior of the second chamber. Additionally, the ion mobility spectrometer and the differential mobility spectrometer form an interface region. Also, the first end and the third end are positioned facing one another so that the constant electric field enters the third end and overlaps the fluid flowing in the second direction.

Object-Orientation is Evil for Mobile Games: Experience from Industrial Mobile RPGs

DEFF Research Database (Denmark)

Zhang, Weishan; Han, Dong; Kunz, Thomas

2007-01-01

Mobile gaming is playing an important role in the entertainment industry. Good performance is a critical requirement for mobile games in order to achieve acceptable running speed although mobile devices are limited by scarce resources. Object-oriented programming is the prevalent programming....... Therefore if developers are aiming for mobile game performance, we conclude that they should use as few OO features as possible. Structural programming can be a very competitive alternative....... paradigm and this is true for mobile game development as well. As the origin of object-orientation (OO) is not targeting the embedded software domain, there is suspicion as to OO's usability for embedded software, especially with respect to mobile games. Questions arise like how OO and to what degree OO...

Mobile economy

OpenAIRE

Turowski, Klaus

2004-01-01

Mobile economy : Transaktionen, Prozesse, Anwendungen und Dienste ; 4. Workshop Mobile Commerce, 02.-03. Februar 2004, Univ. Augsburg / K. Turowski ... (Hrsg.). - Bonn : Ges. für Informatik, 2004. - 189 S. : Ill., graph. Darst. - (GI-Edition : Proceedings ; 42)

Engaging with mobile methods

DEFF Research Database (Denmark)

Jensen, Martin Trandberg

2014-01-01

This chapter showcases how mobile methods are more than calibrated techniques awaiting application by tourism researchers, but productive in the enactment of the mobile (Law and Urry, 2004). Drawing upon recent findings deriving from a PhD course on mobility and mobile methods it reveals...... the conceptual ambiguousness of the term ‘mobile methods’. In order to explore this ambiguousness the chapter provides a number of examples deriving from tourism research, to explore how mobile methods are always entangled in ideologies, predispositions, conventions and practice-realities. Accordingly......, the engagements with methods are acknowledged to be always political and contextual, reminding us to avoid essentialist discussions regarding research methods. Finally, the chapter draws on recent fieldwork to extend developments in mobilities-oriented tourism research, by employing auto-ethnography to call...

Some Mobile Phone Associated Health Problems Among Mobile ...

African Journals Online (AJOL)

Background: Although mobile telecommunications deliver enormous benefit to society, there are concerns whether its electric and magnetic field emissions are linked with cancer or other health hazards. Objectives: 1) determining some of the mobile phone(Mph) associated health problems. 2) identifying some of the risk ...

Quality attributes for mobile applications

OpenAIRE

Fernandes, João M.; Ferreira, André Leite

2016-01-01

A mobile application is a type of software application developed to run on a mobile device. The chapter discusses the main characteristics of mobile devices, since they have a great impact on mobile applications. It also presents the classification of mobile applications according to two main types: native and web-based applications. Finally, this chapter identifies the most relevant types of quality attributes for mobile applications. It shows that the relevant quality attributes for mobile ...

Vertical Scan-Conversion for Filling Purposes

OpenAIRE

Hersch, R. D.

1988-01-01

Conventional scan-conversion algorithms were developed independently of filling algorithms. They cause many problems, when used for filling purposes. However, today's raster printers and plotters require extended use of filling, especially for the generation of typographic characters and graphic line art. A new scan-conversion algorithm, called vertical scan-conversion has been specifically designed to meet the requirements of parity scan line fill algorithms. Vertical scan-conversion ensures...

Fuzzy Logic based Handoff Latency Reduction Mechanism in Layer 2 of Heterogeneous Mobile IPv6 Networks

Science.gov (United States)

Anwar, Farhat; Masud, Mosharrof H.; Latif, Suhaimi A.

2013-12-01

Mobile IPv6 (MIPv6) is one of the pioneer standards that support mobility in IPv6 environment. It has been designed to support different types of technologies for providing seamless communications in next generation network. However, MIPv6 and subsequent standards have some limitations due to its handoff latency. In this paper, a fuzzy logic based mechanism is proposed to reduce the handoff latency of MIPv6 for Layer 2 (L2) by scanning the Access Points (APs) while the Mobile Node (MN) is moving among different APs. Handoff latency occurs when the MN switches from one AP to another in L2. Heterogeneous network is considered in this research in order to reduce the delays in L2. Received Signal Strength Indicator (RSSI) and velocity of the MN are considered as the input of fuzzy logic technique. This technique helps the MN to measure optimum signal quality from APs for the speedy mobile node based on fuzzy logic input rules and makes a list of interfaces. A suitable interface from the list of available interfaces can be selected like WiFi, WiMAX or GSM. Simulation results show 55% handoff latency reduction and 50% packet loss improvement in L2 compared to standard to MIPv6.

Fuzzy Logic based Handoff Latency Reduction Mechanism in Layer 2 of Heterogeneous Mobile IPv6 Networks

International Nuclear Information System (INIS)

Anwar, Farhat; Masud, Mosharrof H; Latif, Suhaimi A

2013-01-01

Mobile IPv6 (MIPv6) is one of the pioneer standards that support mobility in IPv6 environment. It has been designed to support different types of technologies for providing seamless communications in next generation network. However, MIPv6 and subsequent standards have some limitations due to its handoff latency. In this paper, a fuzzy logic based mechanism is proposed to reduce the handoff latency of MIPv6 for Layer 2 (L2) by scanning the Access Points (APs) while the Mobile Node (MN) is moving among different APs. Handoff latency occurs when the MN switches from one AP to another in L2. Heterogeneous network is considered in this research in order to reduce the delays in L2. Received Signal Strength Indicator (RSSI) and velocity of the MN are considered as the input of fuzzy logic technique. This technique helps the MN to measure optimum signal quality from APs for the speedy mobile node based on fuzzy logic input rules and makes a list of interfaces. A suitable interface from the list of available interfaces can be selected like WiFi, WiMAX or GSM. Simulation results show 55% handoff latency reduction and 50% packet loss improvement in L2 compared to standard to MIPv6

MOBILITY: A SYSTEMS APPROACH

OpenAIRE

Mykola I. Striuk; Serhiy O. Semerikov; Andrii M. Striuk

2015-01-01

A comprehensive study on the problem of mobility in the socio-educational and technical systems was carried out: the evolution of the concept of mobility in scientific sources of XIX–XXI centuries was analyzed and the new sources on the issue of mobility introduced into scientific circulation, the interrelation of the types of mobility in the socio-pedagogical and technical systems are theoretically grounded, an integrative model of mobility in the information society is proposed. The major t...

From mobile mental health to mobile wellbeing: opportunities and challenges.

Science.gov (United States)

Gaggioli, Andrea; Riva, Giuseppe

2013-01-01

The combination of smart phones, wearable sensor devices and social media offer new ways of monitoring and promoting mental and physical wellbeing. In this contribution, we describe recent developments in the field of mobile healthcare (or mHealth), by focusing in particular on mobile mental health applications. First, we examine the potential benefits associated with this approach, providing examples from existing projects. Next, we identify and explain possible differences in focus between mobile mental health and mobile wellbeing applications. Finally, we discuss some open challenges associated with the implementation of this vision, ranging from the lack of evidence-based validation to privacy, security and ethical concerns.

Keeping communication mobile

International Nuclear Information System (INIS)

Latimer, Cole

2010-01-01

While mobile phones are ubiquitous in nearly all walks of Australia industry, there is still one sector were the technology has been unsurprisingly absent. Aside from the obvious operational hazards that a mobile phone would encounter when being used underground, such as harsh working conditions, dust and heavy knocks, the technology required to actually use a mobile at depths has been in the early stages for some time. However and Australian company, Mine Site Technologies, has taken a leap into this space by designing the world's first mobile phone for underground mining

Effects of Positioning Aids on Understanding the Relationship Between a Mobile Map and the Environment

Directory of Open Access Journals (Sweden)

Juho Kässi

2013-01-01

Full Text Available Positioning technologies such as GPS enable mobile map applications to display a symbol representing an estimation of a user’s location on a mobile map, therefore acting as a positioning aid. Previous research on the cognitive processes involved in map reading suggests that map readers need at least two map–environment points (objects that are visualized on the map and perceived in the environment for determining their location on a map. Hence, the positioning aid alone does not provide enough information for self-location. Using a field experiment, we assessed the effect of representing the user’s location on a map on the cognitive processes involved in self-location. The results show that positioning aids guide the search for map–environment points and narrow the area on the map that must be scanned for self-location.

Mobile Sensing Systems

Science.gov (United States)

Macias, Elsa; Suarez, Alvaro; Lloret, Jaime

2013-01-01

Rich-sensor smart phones have made possible the recent birth of the mobile sensing research area as part of ubiquitous sensing which integrates other areas such as wireless sensor networks and web sensing. There are several types of mobile sensing: individual, participatory, opportunistic, crowd, social, etc. The object of sensing can be people-centered or environment-centered. The sensing domain can be home, urban, vehicular… Currently there are barriers that limit the social acceptance of mobile sensing systems. Examples of social barriers are privacy concerns, restrictive laws in some countries and the absence of economic incentives that might encourage people to participate in a sensing campaign. Several technical barriers are phone energy savings and the variety of sensors and software for their management. Some existing surveys partially tackle the topic of mobile sensing systems. Published papers theoretically or partially solve the above barriers. We complete the above surveys with new works, review the barriers of mobile sensing systems and propose some ideas for efficiently implementing sensing, fusion, learning, security, privacy and energy saving for any type of mobile sensing system, and propose several realistic research challenges. The main objective is to reduce the learning curve in mobile sensing systems where the complexity is very high. PMID:24351637

Mobile sensing systems.

Science.gov (United States)

Macias, Elsa; Suarez, Alvaro; Lloret, Jaime

2013-12-16

Rich-sensor smart phones have made possible the recent birth of the mobile sensing research area as part of ubiquitous sensing which integrates other areas such as wireless sensor networks and web sensing. There are several types of mobile sensing: individual, participatory, opportunistic, crowd, social, etc. The object of sensing can be people-centered or environment-centered. The sensing domain can be home, urban, vehicular… Currently there are barriers that limit the social acceptance of mobile sensing systems. Examples of social barriers are privacy concerns, restrictive laws in some countries and the absence of economic incentives that might encourage people to participate in a sensing campaign. Several technical barriers are phone energy savings and the variety of sensors and software for their management. Some existing surveys partially tackle the topic of mobile sensing systems. Published papers theoretically or partially solve the above barriers. We complete the above surveys with new works, review the barriers of mobile sensing systems and propose some ideas for efficiently implementing sensing, fusion, learning, security, privacy and energy saving for any type of mobile sensing system, and propose several realistic research challenges. The main objective is to reduce the learning curve in mobile sensing systems where the complexity is very high.

Mobile Sensing Systems

Directory of Open Access Journals (Sweden)

Elsa Macias

2013-12-01

Full Text Available Rich-sensor smart phones have made possible the recent birth of the mobile sensing research area as part of ubiquitous sensing which integrates other areas such as wireless sensor networks and web sensing. There are several types of mobile sensing: individual, participatory, opportunistic, crowd, social, etc. The object of sensing can be people-centered or environment-centered. The sensing domain can be home, urban, vehicular… Currently there are barriers that limit the social acceptance of mobile sensing systems. Examples of social barriers are privacy concerns, restrictive laws in some countries and the absence of economic incentives that might encourage people to participate in a sensing campaign. Several technical barriers are phone energy savings and the variety of sensors and software for their management. Some existing surveys partially tackle the topic of mobile sensing systems. Published papers theoretically or partially solve the above barriers. We complete the above surveys with new works, review the barriers of mobile sensing systems and propose some ideas for efficiently implementing sensing, fusion, learning, security, privacy and energy saving for any type of mobile sensing system, and propose several realistic research challenges. The main objective is to reduce the learning curve in mobile sensing systems where the complexity is very high.

Scan posture definition and hip girth measurement: the impact on clothing design and body scanning.

Science.gov (United States)

Gill, Simeon; Parker, Christopher J

2017-08-01

Ergonomic measurement is central to product design and development; especially for body worn products and clothing. However, there is a large variation in measurement definitions, complicated by new body scanning technology that captures measurements in a posture different to traditional manual methods. Investigations of hip measurement definitions in current clothing measurement practices supports analysis of the effect of scan posture and hip measurement definition on the circumferences of the hip. Here, the hip girth is a key clothing measurement that is not defined in current body scanning measurement standards. Sixty-four participants were scanned in the standard scan posture of a [TC] 2 body scanner, and also in a natural posture similar to that of traditional manual measurement collection. Results indicate that scan posture affects hip girth circumferences, and that some current clothing measurement practices may not define the largest lower body circumference. Recommendations are made concerning how the hip is defined in measurement practice and within body scanning for clothing product development. Practitioner Summary: The hip girth is an important measurement in garment design, yet its measurement protocol is not currently defined. We demonstrate that body posture during body scanning affects hip circumferences, and that current clothing measurement practices may not define the largest lower body circumference. This paper also provides future measurement practice recommendations.

77 FR 64411 - Safety Zone; Cooper T. Smith Fireworks Event; Mobile River; Mobile, AL

Science.gov (United States)

2012-10-22

... 1625-AA00 Safety Zone; Cooper T. Smith Fireworks Event; Mobile River; Mobile, AL AGENCY: Coast Guard... safety zone for a portion of the Mobile River, Mobile, AL in the vicinity of Cooper Riverside Park. This..., mariners, and persons unless specifically authorized by the Captain of the Port Mobile or a designated...

Mastering jQuery mobile

CERN Document Server

Lambert, Chip

2015-01-01

You've started down the path of jQuery Mobile, now begin mastering some of jQuery Mobile's higher level topics. Go beyond jQuery Mobile's documentation and master one of the hottest mobile technologies out there. Previous JavaScript and PHP experience can help you get the most out of this book.

Sustainable Mobility

DEFF Research Database (Denmark)

Kjærulff, Aslak Aamot

This paper combines strands of mobilities theory and planning theory, and develops a qualitative approach to look across emerging planning practices. By actively following 8 Danish urban and transport planners, over the course of 2 years, we learn how their practices have changed, inspired...... by mobility management, a concept aiming to reduce carbon emissions from transportation in western societies. The article focuses on how municipal planners formulate the role of mobility management activities organized around private companies, and how their practices are connected to wider ideas on planning....

A Mobile Nanoscience and Electron Microscopy Outreach Program

Science.gov (United States)

Coffey, Tonya; Kelley, Kyle

2013-03-01

We have established a mobile nanoscience laboratory outreach program in Western NC that puts scanning electron microscopy (SEM) directly in the hands of K-12 students and the general public. There has been a recent push to develop new active learning materials to educate students at all levels about nanoscience and nanotechnology. Previous projects, such as Bugscope, nanoManipulator, or SPM Live! allowed remote access to advanced microscopies. However, placing SEM directly in schools has not often been possible because the cost and steep learning curve of these technologies were prohibitive, making this project quite novel. We have developed new learning modules for a microscopy outreach experience with a tabletop SEM (Hitachi TM3000). We present here an overview of our outreach and results of the assessment of our program to date.

Scanning of Cargo Containers by Gamma-Ray and Fast Neutron Radiography

International Nuclear Information System (INIS)

Yousri, A.M.; Bashter, I.I.; Megahid, M.R.; Osman, A.M.; Kansouh, W.A.; Reda, A.M.

2011-01-01

This paper describes the combined systems which were installed and tested to detect contraband smuggled in cargo containers. These combined systems are based on radiographers work by gamma-rays emitted from point source 60 Co with 0.5 Ci activity and neutrons emitted from point isotopic sources of Pu-α-Be as well as 14 MeV neutrons emitted from sealed tube neutron generator. The transmitted gamma ray through the inspected object was measured by gamma detection system with NaI(Tl) detector while the transmitted fast neutron beam was measured by a neutron gamma detection system with stilbene organic scintillator. The later possess the capability of discrimination between between gamma and neutron pulses using a discrimination system based on pulse shape discrimination method. The measured intensities of primary incident and transmitted beams of gamma-rays and fast neutrons were used to construct 2D cross-sectional images of the inspected objects hidden directly within benign materials of the container and for object screened by high dense material to stop object detection by gamma or X-rays. The constructed images for the inspected objects show the good capability and effectiveness of the installed gamma and neutron radiographers to detect illicit materials hidden in air cargo containers and sea containers of med size. They have also indicated that the developed scanning systems possess the ease of mobility and low cost of scanning

Thyroid Scan and Uptake

Medline Plus

Full Text Available ... Scan and Uptake Thyroid scan and uptake uses small amounts of radioactive materials called radiotracers, a special ... is a branch of medical imaging that uses small amounts of radioactive material to diagnose and determine ...

Thyroid Scan and Uptake

Medline Plus

Full Text Available ... of page What will I experience during and after the procedure? Most thyroid scan and thyroid uptake ... you otherwise, you may resume your normal activities after your nuclear medicine scan. If any special instructions ...

THE RELATIONSHIP BETWEEN TEMPOROMANDIBULAR-JOINT MOBILITY AND PERIPHERAL JOINT MOBILITY RECONSIDERED

NARCIS (Netherlands)

Dijkstra, P.U.; DEBONT, L.G.M.; VANDERWEELE, L.T.; Boering, G.

The purpose of this paper was to study the relationship between temporomandibular joint (TMJ) mobility and mobility of joints and to study the general character of joint mobility in 83 subjects, 55 females and 28 males (mean age 26.7, range 13-46 years). The subjects were recruited from the

Mobile learning in medicine

Science.gov (United States)

Serkan Güllüoüǧlu, Sabri

2013-03-01

This paper outlines the main infrastructure for implicating mobile learning in medicine and present a sample mobile learning application for medical learning within the framework of mobile learning systems. Mobile technology is developing nowadays. In this case it will be useful to develop different learning environments using these innovations in internet based distance education. M-learning makes the most of being on location, providing immediate access, being connected, and acknowledges learning that occurs beyond formal learning settings, in places such as the workplace, home, and outdoors. Central to m-learning is the principle that it is the learner who is mobile rather than the device used to deliver m learning. The integration of mobile technologies into training has made learning more accessible and portable. Mobile technologies make it possible for a learner to have access to a computer and subsequently learning material and activities; at any time and in any place. Mobile devices can include: mobile phone, personal digital assistants (PDAs), personal digital media players (eg iPods, MP3 players), portable digital media players, portable digital multimedia players. Mobile learning (m-learning) is particularly important in medical education, and the major users of mobile devices are in the field of medicine. The contexts and environment in which learning occurs necessitates m-learning. Medical students are placed in hospital/clinical settings very early in training and require access to course information and to record and reflect on their experiences while on the move. As a result of this paper, this paper strives to compare and contrast mobile learning with normal learning in medicine from various perspectives and give insights and advises into the essential characteristics of both for sustaining medical education.

Mobile Virtual Reality : A Solution for Big Data Visualization

Science.gov (United States)

Marshall, E.; Seichter, N. D.; D'sa, A.; Werner, L. A.; Yuen, D. A.

2015-12-01

Pursuits in geological sciences and other branches of quantitative sciences often require data visualization frameworks that are in continual need of improvement and new ideas. Virtual reality is a medium of visualization that has large audiences originally designed for gaming purposes; Virtual reality can be captured in Cave-like environment but they are unwieldy and expensive to maintain. Recent efforts by major companies such as Facebook have focussed more on a large market , The Oculus is the first of such kind of mobile devices The operating system Unity makes it possible for us to convert the data files into a mesh of isosurfaces and be rendered into 3D. A user is immersed inside of the virtual reality and is able to move within and around the data using arrow keys and other steering devices, similar to those employed in XBox.. With introductions of products like the Oculus Rift and Holo Lens combined with ever increasing mobile computing strength, mobile virtual reality data visualization can be implemented for better analysis of 3D geological and mineralogical data sets. As more new products like the Surface Pro 4 and other high power yet very mobile computers are introduced to the market, the RAM and graphics card capacity necessary to run these models is more available, opening doors to this new reality. The computing requirements needed to run these models are a mere 8 GB of RAM and 2 GHz of CPU speed, which many mobile computers are starting to exceed. Using Unity 3D software to create a virtual environment containing a visual representation of the data, any data set converted into FBX or OBJ format which can be traversed by wearing the Oculus Rift device. This new method for analysis in conjunction with 3D scanning has potential applications in many fields, including the analysis of precious stones or jewelry. Using hologram technology to capture in high-resolution the 3D shape, color, and imperfections of minerals and stones, detailed review and

The boundary-scan handbook

CERN Document Server

Parker, Kenneth P

2016-01-01

Aimed at electronics industry professionals, this 4th edition of the Boundary Scan Handbook describes recent changes to the IEEE1149.1 Standard Test Access Port and Boundary-Scan Architecture. This updated edition features new chapters on the possible effects of the changes on the work of the practicing test engineers and the new 1149.8.1 standard. Anyone needing to understand the basics of boundary scan and its practical industrial implementation will need this book. Provides an overview of the recent changes to the 1149.1 standard and the effect of the changes on the work of test engineers;   Explains the new IEEE 1149.8.1 subsidiary standard and applications;   Describes the latest updates on the supplementary IEEE testing standards. In particular, addresses: IEEE Std 1149.1                      Digital Boundary-Scan IEEE Std 1149.4                      Analog Boundary-Scan IEEE Std 1149.6                      Advanced I/O Testing IEEE Std 1149.8.1           �...

"Agency in Mobility": Towards a Conceptualisation of International Student Agency in Transnational Mobility

Science.gov (United States)

Tran, Ly Thi; Vu, Thao Thi Phuong

2018-01-01

Student mobility is becoming a prominent phenomenon of tertiary education in the twenty-first century. Internationally mobile students' lived experiences are intimately linked to their potential to exercise agency in transnational mobility. However, the notion of agency within the context of student mobility has not been the explicit focus of…

Intercomparison of two dynamic treatment techniques, ring scan and spot scan, for head and neck tumors with the Piotron

International Nuclear Information System (INIS)

Takai, M.; Blattmann, H.; Pedroni, E.

1988-01-01

An evaluation of the ring scan and the spot scan was made for the pion irradiation of head and neck tumors with the Piotron. For the geometry of the Piotron, with its 60 radially converging beams, two scanning techniques have been developed, ring scan and spot scan. They have different characteristics concerning achievable dose distributions and sensitivity to tissue inhomogenities. The optimized 3-dimensional dose distributions for the treatment with ring scan and spot scan techniques were calculated for two examples of the target volume. The comparison of the dose distributions has shown that the ring scan is better in sparing normal tissues than the spot scan for a simple shape target volume but not for an irregular shape target volume with the present status of the technique. The irradiation time needed for the ring scan is longer, for the present examples three times, than for the spot scan. From the practical view point the spot scan is preferable to the ring scan for the treatment of head and neck tumors with the Piotron

Multiple myeloma: radiology or bone scanning