Thermal decomposition and reaction of confined explosives

International Nuclear Information System (INIS)

Catalano, E.; McGuire, R.; Lee, E.; Wrenn, E.; Ornellas, D.; Walton, J.

1976-01-01

Some new experiments designed to accurately determine the time interval required to produce a reactive event in confined explosives subjected to temperatures which will cause decomposition are described. Geometry and boundary conditions were both well defined so that these experiments on the rapid thermal decomposition of HE are amenable to predictive modelling. Experiments have been carried out on TNT, TATB and on two plastic-bonded HMX-based high explosives, LX-04 and LX-10. When the results of these experiments are plotted as the logarithm of the time to explosion versus 1/T K (Arrhenius plot), the curves produced are remarkably linear. This is in contradiction to the results obtained by an iterative solution of the Laplace equation for a system with a first order rate heat source. Such calculations produce plots which display considerable curvature. The experiments have also shown that the time to explosion is strongly influenced by the void volume in the containment vessel. Results of the experiments with calculations based on the heat flow equations coupled with first-order models of chemical decomposition are compared. The comparisons demonstrate the need for a more realistic reaction model

Effect of Temperature Profile on Reaction Violence in Heated, Self-Ignited, PBX-9501

Science.gov (United States)

Asay, Blaine; Dickson, Peter; Henson, Bryan; Smilowitz, Laura; Tellier, Larry

2001-06-01

Historically, the location of ignition in heated explosives has been implicated in the violence of subsequent reactions. This is based on the observation that typically, when an explosive is heated quickly, ignition occurs at the surface, leading to premature failure of confinement, a precipitous drop in pressure, and failure of the reaction. During slow heating, reaction usually occurs near the center of the charge, and more violent reactions are observed. Many safety protocols use these global results in determining safety envelopes and procedures. We have conducted instrumented experiments with cylindrical symmetry and precise thermal boundary conditions which have shown that the temperature profile in the explosive, along with the time spent at critical temperatures, and not the location of ignition, are responsible for the level of violence observed. Microwave interferometry was used to measure case expansion velocities and reaction violence. We are using the data in a companion study to develop better kinetic models for HMX and PBX 9501. Additionally, the spatially- and temporally-resolved temperature data are being made available for those who would like to use them.

Pre-ignition confinement and deflagration violence in LX-10 and PBX 9501

Energy Technology Data Exchange (ETDEWEB)

Tringe, J. W., E-mail: tringe2@llnl.gov; Glascoe, E. A.; McClelland, M. A.; Greenwood, D.; Chambers, R. D.; Springer, H. K.; Levie, H. W. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States)

2014-08-07

In thermal explosions of the nitramine octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX)-based explosives LX-10 and PBX-9501, the pre-ignition spatial and temporal heating profile defines the ignition location. The ignition location then determines the extent of inertial confinement and the violence of the resulting deflagration. In this work, we present results of experiments in which ∼23 g cylinders of LX-10 and PBX 9501 in thin-walled aluminum confinement vessels were subjected to identical heating profiles but which presented starkly different energy release signatures. Post-explosion LX-10 containment vessels were completely fragmented, while the PBX 9501 vessels were merely ruptured. Flash x-ray radiography images show that the initiation location for the LX-10 is a few mm farther from the end caps of the vessel relative to the initiation location of PBX 9501. This difference increases deflagration confinement for LX-10 at the time of ignition and extends the pressurization time during which the deflagration front propagates in the explosive. The variation in the initiation location, in turn, is determined by the thermal boundary conditions, which differ for these two explosives because of the larger coefficient of thermal expansion and greater thermal stability of the Viton binder in LX-10 relative to the estane and bis(2,2-dinitropropyl) acetal/formal binder of the PBX 9501. The thermal profile and initiation location were modeled for LX-10 using the hydrodynamics and structures code ALE3D; results indicate temperatures in the vicinity of the ignition location in excess of 274 °C near the time of ignition. The conductive burn rates for these two explosives, as determined by flash x-ray radiography, are comparable in the range 0.1–0.2 mm/μs, somewhat faster than rates observed by strand burner experiments for explosives in the temperature range 150–180 °C and pressures up to 100 MPa. The thinnest-wall aluminum containment vessels

Pre-ignition confinement and deflagration violence in LX-10 and PBX 9501

International Nuclear Information System (INIS)

Tringe, J. W.; Glascoe, E. A.; McClelland, M. A.; Greenwood, D.; Chambers, R. D.; Springer, H. K.; Levie, H. W.

2014-01-01

In thermal explosions of the nitramine octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX)-based explosives LX-10 and PBX-9501, the pre-ignition spatial and temporal heating profile defines the ignition location. The ignition location then determines the extent of inertial confinement and the violence of the resulting deflagration. In this work, we present results of experiments in which ∼23 g cylinders of LX-10 and PBX 9501 in thin-walled aluminum confinement vessels were subjected to identical heating profiles but which presented starkly different energy release signatures. Post-explosion LX-10 containment vessels were completely fragmented, while the PBX 9501 vessels were merely ruptured. Flash x-ray radiography images show that the initiation location for the LX-10 is a few mm farther from the end caps of the vessel relative to the initiation location of PBX 9501. This difference increases deflagration confinement for LX-10 at the time of ignition and extends the pressurization time during which the deflagration front propagates in the explosive. The variation in the initiation location, in turn, is determined by the thermal boundary conditions, which differ for these two explosives because of the larger coefficient of thermal expansion and greater thermal stability of the Viton binder in LX-10 relative to the estane and bis(2,2-dinitropropyl) acetal/formal binder of the PBX 9501. The thermal profile and initiation location were modeled for LX-10 using the hydrodynamics and structures code ALE3D; results indicate temperatures in the vicinity of the ignition location in excess of 274 °C near the time of ignition. The conductive burn rates for these two explosives, as determined by flash x-ray radiography, are comparable in the range 0.1–0.2 mm/μs, somewhat faster than rates observed by strand burner experiments for explosives in the temperature range 150–180 °C and pressures up to 100 MPa. The thinnest-wall aluminum containment vessels

Effect of Temperature Profile on Reaction Violence in Heated and Self-Ignited PBX 9501

Science.gov (United States)

Asay, Blaine; Dickson, Peter; Henson, Bryan; Smilowitz, Laura; Tellier, Larry

2002-07-01

Historically, the location of ignition in heated explosives has been implicated in the violence of subsequent reactions. This is based on the observation that typically, when an explosive is heated quickly, ignition occurs at the surface, leading to premature failure of confinement, a precipitous drop in pressure, and failure of the reaction. During slow heating, reaction usually occurs near the center of the charge, and more violent reactions are observed. Many safety protocols use these global results in determining safety envelopes and procedures. We are conducting instrumented experiments with cylindrical symmetry and precise thermal boundary conditions which are beginning to show that the temperature profile in the explosive, along with the time spent at critical temperatures, and not the location of ignition, are responsible for the level of violence observed. Microwave interferometry was used to measure case expansion velocities which can be considered a measure of reaction violence. We are using the data in a companion study to develop better kinetic models for HMX and PBX 9501. Additionally, the spatially- and temporally-resolved temperature data are being made available for those who would like to use them.

First vapor explosion calculations performed with MC3D thermal-hydraulic code

Energy Technology Data Exchange (ETDEWEB)

Brayer, C.; Berthoud, G. [CEA Centre d`Etudes de Grenoble, 38 (France). Direction des Reacteurs Nucleaires

1998-01-01

This paper presents the first calculations performed with the `explosion` module of the multiphase computer code MC3D, which is devoted to the fine fragmentation and explosion phase of a fuel coolant interaction. A complete description of the physical laws included in this module is given. The fragmentation models, taking into account two fragmentation mechanisms, a thermal one and an hydrodynamic one, are also developed here. Results to some calculations to test the numerical behavior of MC3D and to test the explosion models in 1D or 2D are also presented. (author)

Influence of variable heat transfer coefficient of fireworks and crackers on thermal explosion critical ambient temperature and time to ignition

Directory of Open Access Journals (Sweden)

Guo Zerong

2016-01-01

Full Text Available To study the effect of variable heat transfer coefficient of fireworks and crackers on thermal explosion critical ambient temperature and time to ignition, considering the heat transfer coefficient as the power function of temperature, mathematical thermal explosion steady state and unsteady-state model of finite cylindrical fireworks and crackers with complex shell structures are established based on two-dimensional steady state thermal explosion theory. The influence of variable heat transfer coefficient on thermal explosion critical ambient temperature and time to ignition are analyzed. When heat transfer coefficient is changing with temperature and in the condition of natural convection heat transfer, critical ambient temperature lessen, thermal explosion time to ignition shorten. If ambient temperature is close to critical ambient temperature, the influence of variable heat transfer coefficient on time to ignition become large. For firework with inner barrel in example analysis, the critical ambient temperature of propellant is 463.88 K and the time to ignition is 4054.9s at 466 K, 0.26 K and 450.8s less than without considering the change of heat transfer coefficient respectively. The calculation results show that the influence of variable heat transfer coefficient on thermal explosion time to ignition is greater in this example. Therefore, the effect of variable heat transfer coefficient should be considered into thermal safety evaluation of fireworks to reduce potential safety hazard.

mathematical model of thermal explosion, the dual variational formulation of nonlinear problem, alternative functional

Directory of Open Access Journals (Sweden)

V. S. Zarubin

2016-01-01

Full Text Available A temperature state of the solid body may depend both on the conditions of heat exchange with external environment surrounding its surface and on the energy release within the body volume, caused, for example, by the processes in nuclear reactor elements or exothermic chemical reactions, absorption of penetrating radiation energy or transformation of a part of the electrical power into heat with flowing electric current (so-called Joule heat.If with growing temperature the intensity of bulk power density increases, a limited steady temperature state can emerge at which heat extracted to the body surface and released within its volume reaches maximum. Thus, small increments of temperature lead to an increase of heat release, which can not be extracted to the body surface by conduction without further temperature increase. As a result, the steady temperature distribution in the body becomes impossible that determines the state of the thermal explosion, so named due to the fact that in this case the appropriate mathematical model predicts an unlimited temperature increase.A lot of published papers and monographs concerning the study of the combustion and explosion processes in a stationary medium analyse the thermal explosion state. The most famous papers consider a mathematical model to describe a temperature distribution in the case when heat release is because of exothermic chemical reactions the rate of which increases with temperature growth. The dependence of the chemical reaction rate on temperature is usually described by the exponential Arrhenius law, which makes it necessary to consider an essentially nonlinear mathematical model containing differential equation, which includes the term, nonlinearly rising with increasing temperature. Even with simplifying assumptions, this model allows an exact closed form solution only in the case of one-dimensional temperature distributions in the two areas of the canonical form: in the plate, infinite

A COMPARISON OF THERMAL EXPLOSIONS IN PBX 9501 AND PBXN-9

International Nuclear Information System (INIS)

Smilowitz, L.; Henson, B. F.; Romero, J. J.; Asay, B. W.

2009-01-01

We have used a variety of observables to study the response of HMX based energetic materials formulations to thermal stimuli. In this paper, we compare the response of PBX 9501 and PBXN-9 to a temperature of 205 deg. C. Both undergo thermal runaway at this boundary condition with similar preignition behavior. However, the post-ignition burn propagations of the two formulations are very different with the final reaction violence significantly lower for PBXN-9 than for PBX 9501.

Intermittent explosive disorder amongst women in conflict affected Timor-Leste: associations with human rights trauma, ongoing violence, poverty, and injustice.

Science.gov (United States)

Rees, Susan; Silove, Derrick; Verdial, Teresa; Tam, Natalino; Savio, Elisa; Fonseca, Zulmira; Thorpe, Rosamund; Liddell, Belinda; Zwi, Anthony; Tay, Kuowei; Brooks, Robert; Steel, Zachary

2013-01-01

Women in conflict-affected countries are at risk of mental disorders such as posttraumatic stress disorder and depression. No studies have investigated the association between experiences of abuse and injustice and explosive anger amongst women in these settings, and the impact of anger on women's health, family relationships and ability to participate in development. A mixed methods study including an epidemiological survey (n = 1513, 92.6% response) and qualitative interviews (n = 77) was conducted in Timor-Leste. The indices measured included Intermittent Explosive Disorder, posttraumatic stress disorder; severe distress; days out of role (the number of days that the person was unable to undertake normal activities); gender-specific trauma; conflict/violence; poverty; and preoccupations with injustice. Women with Intermittent Explosive Disorder (n = 184, 12.2%) were more disabled than those without the disorder (for >5 days out of role, 40.8% versus 31.5%, X(2) (2) = 12.93 p = 0.0016). Multivariable associations with Intermittent Explosive Disorder, controlling for the presence of PTSD, psychological distress and other predictors in the model, included the sense of being sick (OR 1.73; 95% CI 1.08-2.77); victimization as a result of helping the resistance movement (OR 2.33, 95% CI 1.48-3.68); war-related trauma specific to being a woman (OR 1.95, 95%, CI 1.09-3.50); ongoing family violence and community conflict (OR 1.88, 95% CI 1.27-2.77); extreme poverty (OR 1.23, 95%, CI 1.08-1.39); and distressing preoccupations with injustice (relating to 2/3 historical periods, OR 2.10, 95% CI 1.35-3.28). In the qualitative study, women elaborated on the determinants of anger and its impact on their health, family and community functioning, child-rearing, and capacity to engage in development. Women reflected on the strategies that might help them overcome their anger. Intermittent Explosive Disorder is prevalent and disabling amongst women in conflict-affected Timor

Detection of Nonvolatile Inorganic Oxidizer-Based Explosives from Wipe Collections by Infrared Thermal Desorption-Direct Analysis in Real Time Mass Spectrometry.

Science.gov (United States)

Forbes, Thomas P; Sisco, Edward; Staymates, Matthew

2018-05-07

Infrared thermal desorption (IRTD) was coupled with direct analysis in real time mass spectrometry (DART-MS) for the detection of both inorganic and organic explosives from wipe collected samples. This platform generated discrete and rapid heating rates that allowed volatile and semivolatile organic explosives to thermally desorb at relatively lower temperatures, while still achieving elevated temperatures required to desorb nonvolatile inorganic oxidizer-based explosives. IRTD-DART-MS demonstrated the thermal desorption and detection of refractory potassium chlorate and potassium perchlorate oxidizers, compounds difficult to desorb with traditional moderate-temperature resistance-based thermal desorbers. Nanogram to sub-nanogram sensitivities were established for analysis of a range of organic and inorganic oxidizer-based explosive compounds, with further enhancement limited by the thermal properties of the most common commercial wipe materials. Detailed investigations and high-speed visualization revealed conduction from the heated glass-mica base plate as the dominant process for heating of the wipe and analyte materials, resulting in thermal desorption through boiling, aerosolization, and vaporization of samples. The thermal desorption and ionization characteristics of the IRTD-DART technique resulted in optimal sensitivity for the formation of nitrate adducts with both organic and inorganic species. The IRTD-DART-MS coupling and IRTD in general offer promising explosive detection capabilities to the defense, security, and law enforcement arenas.

Energy and impacts of pressure vessel explosions

International Nuclear Information System (INIS)

Kurttila, H.

1999-01-01

In this paper the explosion energy is considered to be same as the energy of pressure vessel discharge. This is the maximum energy which can be obtained from the process. The energy can be used or it can cause the violence of an explosion accident. (orig.)

LX-04 VIOLENCE MEASUREMENTS- STEVEN TESTS IMPACTED BY PROJECTILES SHOT FROM A HOWITZER GUN

International Nuclear Information System (INIS)

Chidester, S K; Vandersall, K S; Switzer, L L; Tarver, C M

2005-01-01

Characterization of the reaction violence of LX-04 explosive (85% HMX and 15% Viton A by weight) was obtained from Steven Impact Tests performed above the reaction initiation threshold. A 155 mm Howitzer propellant driven gas gun was used to accelerate the Steven Test projectiles in the range of approximately 170-300 m/s to react (ignite) the LX-04 explosive. Blast overpressure gauges, acoustic microphones, and high-speed photography characterized the level of high explosive reaction violence. A detonation in this velocity range was not observed and when comparing these results (and the Susan test results) with that of other HMX based explosives, LX-04 has a more gradual reaction violence slope as the impact velocity increases. The high binder content (15%) of the LX-04 explosive is believed to be the key factor to the lower level of violence

Thermal hazard assessment of AN and AN-based explosives.

Science.gov (United States)

Turcotte, R; Lightfoot, P D; Fouchard, R; Jones, D E G

2003-07-04

Ammonium nitrate (AN) is an essential ingredient in most fertilizers. It is also widely used in the commercial explosives industry. In this latter application, it is mostly mixed with fuel oil to form the most popular commercial explosive: ANFO. In both the fertilizer and the explosive industry, aqueous AN solutions (ANS) of various concentrations are processed. These solutions also form the basis of ammonium nitrate emulsion explosives (also called ammonium nitrate emulsions or ANE), which are produced either in bulk or in packaged form. For all these AN-based products, quantities of the order of 20,000kg are being manufactured, transported, stored, and processed at elevated temperatures and/or elevated pressures. Correspondingly, major accidents involving overheating of large quantities of these products have happened in several of these operations. In comparison, convenient laboratory quantities to investigate thermal decomposition properties are generally less than 1kg. As a result, in order to provide information applicable to real-life situations, any laboratory study must use techniques that minimize heat losses from the samples to their environment. In the present study, two laboratory-scale calorimeters providing an adiabatic environment were used: an accelerating rate calorimeter (ARC) and an adiabatic Dewar calorimeter (ADC). Experiments were performed on pure AN, ANFO, various ANS systems, and typical bulk and packaged ANE systems. The effects of sample mass, atmosphere, and formulation on the resulting onset temperatures were studied. A comparison of the results from the two techniques is provided and a proposed method to extrapolate these results to large-scale inventories is examined.

Intermittent Explosive Disorder amongst Women in Conflict Affected Timor-Leste: Associations with Human Rights Trauma, Ongoing Violence, Poverty, and Injustice

Science.gov (United States)

Rees, Susan; Silove, Derrick; Verdial, Teresa; Tam, Natalino; Savio, Elisa; Fonseca, Zulmira; Thorpe, Rosamund; Liddell, Belinda; Zwi, Anthony; Tay, Kuowei; Brooks, Robert; Steel, Zachary

2013-01-01

Introduction Women in conflict-affected countries are at risk of mental disorders such as posttraumatic stress disorder and depression. No studies have investigated the association between experiences of abuse and injustice and explosive anger amongst women in these settings, and the impact of anger on women's health, family relationships and ability to participate in development. Methods A mixed methods study including an epidemiological survey (n = 1513, 92.6% response) and qualitative interviews (n = 77) was conducted in Timor-Leste. The indices measured included Intermittent Explosive Disorder, posttraumatic stress disorder; severe distress; days out of role (the number of days that the person was unable to undertake normal activities); gender-specific trauma; conflict/violence; poverty; and preoccupations with injustice. Results Women with Intermittent Explosive Disorder (n = 184, 12.2%) were more disabled than those without the disorder (for >5 days out of role, 40.8% versus 31.5%, X2 (2)  = 12.93 p = 0.0016). Multivariable associations with Intermittent Explosive Disorder, controlling for the presence of PTSD, psychological distress and other predictors in the model, included the sense of being sick (OR 1.73; 95% CI 1.08–2.77); victimization as a result of helping the resistance movement (OR 2.33, 95% CI 1.48–3.68); war-related trauma specific to being a woman (OR 1.95, 95%, CI 1.09–3.50); ongoing family violence and community conflict (OR 1.88, 95% CI 1.27–2.77); extreme poverty (OR 1.23, 95%, CI 1.08–1.39); and distressing preoccupations with injustice (relating to 2/3 historical periods, OR 2.10, 95% CI 1.35–3.28). In the qualitative study, women elaborated on the determinants of anger and its impact on their health, family and community functioning, child-rearing, and capacity to engage in development. Women reflected on the strategies that might help them overcome their anger. Conclusions Intermittent Explosive Disorder

Intermittent explosive disorder amongst women in conflict affected Timor-Leste: associations with human rights trauma, ongoing violence, poverty, and injustice.

Directory of Open Access Journals (Sweden)

Susan Rees

Full Text Available INTRODUCTION: Women in conflict-affected countries are at risk of mental disorders such as posttraumatic stress disorder and depression. No studies have investigated the association between experiences of abuse and injustice and explosive anger amongst women in these settings, and the impact of anger on women's health, family relationships and ability to participate in development. METHODS: A mixed methods study including an epidemiological survey (n = 1513, 92.6% response and qualitative interviews (n = 77 was conducted in Timor-Leste. The indices measured included Intermittent Explosive Disorder, posttraumatic stress disorder; severe distress; days out of role (the number of days that the person was unable to undertake normal activities; gender-specific trauma; conflict/violence; poverty; and preoccupations with injustice. RESULTS: Women with Intermittent Explosive Disorder (n = 184, 12.2% were more disabled than those without the disorder (for >5 days out of role, 40.8% versus 31.5%, X(2 (2 = 12.93 p = 0.0016. Multivariable associations with Intermittent Explosive Disorder, controlling for the presence of PTSD, psychological distress and other predictors in the model, included the sense of being sick (OR 1.73; 95% CI 1.08-2.77; victimization as a result of helping the resistance movement (OR 2.33, 95% CI 1.48-3.68; war-related trauma specific to being a woman (OR 1.95, 95%, CI 1.09-3.50; ongoing family violence and community conflict (OR 1.88, 95% CI 1.27-2.77; extreme poverty (OR 1.23, 95%, CI 1.08-1.39; and distressing preoccupations with injustice (relating to 2/3 historical periods, OR 2.10, 95% CI 1.35-3.28. In the qualitative study, women elaborated on the determinants of anger and its impact on their health, family and community functioning, child-rearing, and capacity to engage in development. Women reflected on the strategies that might help them overcome their anger. CONCLUSIONS: Intermittent Explosive Disorder is prevalent and

DETERMINING OF THERMAL STABILITY OF EXPLOSIVES FOR CIVIL USES MODERN EQUIPMENT EQUIPPED WITH AUTOMATIC TEMPERATURE AND PRESSURE

Directory of Open Access Journals (Sweden)

Gabriel VASILESCU

2015-07-01

Full Text Available Thermal stability of explosives for civil use is a key security parameter. When the explosive is exposed to high tempera-tures in a given period of time can lead to undesirable phenomena such as decomposing or even very dangerous as un-controlled detonation.

Trace level detection of explosives in solution using leidenfrost phenomenon assisted thermal desorption ambient mass spectrometry.

Science.gov (United States)

Saha, Subhrakanti; Mandal, Mridul Kanti; Chen, Lee Chuin; Ninomiya, Satoshi; Shida, Yasuo; Hiraoka, Kenzo

2013-01-01

The present paper demonstrates the detection of explosives in solution using thermal desorption technique at a temperature higher than Leidenfrost temperature of the solvent in combination with low temperature plasma (LTP) ionization. Leidenfrost temperature of a solvent is the temperature above which the solvent droplet starts levitation instead of splashing when placed on a hot metallic surface. During this desorption process, slow and gentle solvent evaporation takes place, which leads to the pre-concentration of less-volatile explosive molecules in the droplet and the explosive molecules are released at the last moment of droplet evaporation. The limits of detection for explosives studied by using this thermal desorption LTP ionization method varied in a range of 1 to 10 parts per billion (ppb) using a droplet volume of 20 μL (absolute sample amount 90-630 fmol). As LTP ionization method was applied and ion-molecule reactions took place in ambient atmosphere, various ion-molecule adduct species like [M+NO2](-), [M+NO3](-), [M+HCO3](-), [M+HCO4](-) were generated together with [M-H](-) peak. Each peak was unambiguously identified using 'Exactive Orbitrap' mass spectrometer in negative ionization mode within 3 ppm deviation compared to its exact mass. This newly developed technique was successfully applied to detect four explosives contained in the pond water and soil sample with minor sample pre-treatment and the explosives were detected with ppb levels. The present method is simple, rapid and can detect trace levels of explosives with high specificity from solutions.

Reliability analysis for thermal cutting method based non-explosive separation device

International Nuclear Information System (INIS)

Choi, Jun Woo; Hwang, Kuk Ha; Kim, Byung Kyu

2016-01-01

In order to increase the reliability of a separation device for a small satellite, a new non-explosive separation device is invented. This device is activated using a thermal cutting method with a Ni-Cr wire. A reliability analysis is carried out for the proposed non-explosive separation device by applying the Fault tree analysis (FTA) method. In the FTA results for the separation device, only ten single-point failure modes are found. The reliability modeling and analysis for the device are performed considering failure of the power supply, the Ni-Cr wire burns failure and unwinds, the holder separation failure, the balls separation failure, and the pin release failure. Ultimately, the reliability of the proposed device is calculated as 0.999989 with five Ni-Cr wire coils

Reliability analysis for thermal cutting method based non-explosive separation device

Energy Technology Data Exchange (ETDEWEB)

Choi, Jun Woo; Hwang, Kuk Ha; Kim, Byung Kyu [Korea Aerospace University, Goyang (Korea, Republic of)

2016-12-15

In order to increase the reliability of a separation device for a small satellite, a new non-explosive separation device is invented. This device is activated using a thermal cutting method with a Ni-Cr wire. A reliability analysis is carried out for the proposed non-explosive separation device by applying the Fault tree analysis (FTA) method. In the FTA results for the separation device, only ten single-point failure modes are found. The reliability modeling and analysis for the device are performed considering failure of the power supply, the Ni-Cr wire burns failure and unwinds, the holder separation failure, the balls separation failure, and the pin release failure. Ultimately, the reliability of the proposed device is calculated as 0.999989 with five Ni-Cr wire coils.

Modeling of thermal explosion under pressure in metal ceramic systems

International Nuclear Information System (INIS)

Shapiro, M.; Dudko, V.; Skachek, B.; Matvienko, A.; Gotman, I.; Gutmanas, E.Y.

1998-01-01

The process of reactive in situ synthesis of dense ceramic matrix composites in Ti-B-C, Ti-B-N, Ti-Si-N systems is modeled. These ceramics are fabricated on the basis of compacted blends of ceramic powders, namely Ti-B 4 C and/or Ti-BN. The objectives of the project are to identify and investigate the optimal thermal conditions preferable for production of fully dense ceramic matrix composites. Towards this goal heat transfer and combustion in dense and porous ceramic blends are investigated during monotonous heating at a constant rate. This process is modeled using a heat transfer-combustion model with kinetic parameters determined from the differential thermal analysis of the experimental data. The kinetic burning parameters and the model developed are further used to describe the thermal explosion synthesis in a restrained die under pressure. It is shown that heat removal from the reaction zone affects the combustion process and the final phase composition

Disappearance of criticality in branched-chain thermal explosion with heat loss

International Nuclear Information System (INIS)

Okoya, Samuel S.

2003-09-01

In the framework of the currently developed branched-chain thermal explosion theory, the equation governing leakage through a hole of a reaction vessel is given. The critical ignition, extinction and transition temperature excess, activation energy parameter and modified Semenov's number are estimated employing this equation. We calculated numerically and obtained analytically these non-dimensional parameters with and without initiation respectively. The similar solution for Semenov model appear as a limiting case of our solution. We also obtained the ignition times. (author)

Thermal explosion analysis of methyl ethyl ketone peroxide by non-isothermal and isothermal calorimetric applications

International Nuclear Information System (INIS)

Chi, Jen-Hao; Wu, Sheng-Hung; Shu, Chi-Min

2009-01-01

In the past, process incidents attributed to organic peroxides (OPs) that involved near misses, over-pressures, runaway reactions, and thermal explosions occurred because of poor training, human error, incorrect kinetic assumptions, insufficient change management, and inadequate chemical knowledge in the manufacturing process. Calorimetric applications were employed broadly to test organic peroxides on a small-scale because of their thermal hazards, such as exothermic behavior and self-accelerating decomposition in the laboratory. In essence, methyl ethyl ketone peroxide (MEKPO) is highly reactive and exothermically unstable. In recent years, it has undergone many thermal explosions and runaway reaction incidents in the manufacturing process. Differential scanning calorimetry (DSC), vent sizing package 2 (VSP2), and thermal activity monitor (TAM) were employed to analyze thermokinetic parameters and safety index. The intent of the analyses was to facilitate the use of various auto-alarm equipments to detect over-pressure, over-temperature, and hazardous materials leaks for a wide spectrum of operations. Results indicated that MEKPO decomposition is detected at low temperatures (30-40 deg. C), and the rate of decomposition was shown to exponentially increase with temperature and pressure. Determining time to maximum rate (TMR), self-accelerating decomposition temperature (SADT), maximum temperature (T max ), exothermic onset temperature (T 0 ), and heat of decomposition (ΔH d ) was essential for identifying early-stage runaway reactions effectively for industries.

Thermal chemical-mechanical reactive flow model of shock initiation in solid explosives

International Nuclear Information System (INIS)

Nicholls, A.L. III; Tarver, C.M.

1998-01-01

The three dimensional Arbitrary Lagrange Eulerian hydrodynamic computer code ALE3D with fully coupled thermal-chemical-mechanical material models provides the framework for the development of a physically realistic model of shock initiation and detonation of solid explosives. The processes of hot spot formation during shock compression, subsequent ignition of reaction or failure to react, growth of reaction in individual hot spots, and coalescence of reacting hot spots during the transition to detonation can now be modeled using Arrhenius chemical kinetic rate laws and heat transfer to propagate the reactive flow. This paper discusses the growth rates of reacting hot spots in HMX and TATB and their coalescence during shock to detonation transition. Hot spot deflagration rates are found to be fast enough to consume explosive particles less than 10 mm in diameter during typical shock duration times, but larger particles must fragment and create more reactive surface area in order to be rapidly consumed

Investigation of coal dust explosion hazard at the Nikola Tesla-A thermal power station

Energy Technology Data Exchange (ETDEWEB)

Golubovic, D

1987-10-01

Reports on investigations into coal dust explosion hazards in working places with high coal dust exposure, done in the Tesla-A thermal power station by Mining Institute of Belgrade specialists. Settled and floating coal dust concentrations were monitored for six months and samples analyzed for explosibility under lab conditions. Samples from transport and preparation facilities and the power station boiler house were taken. The entire plant was divided into 4 zones, depending on intensity of dust settlement and ventilation system. Coal dust generation varied from 0.3-65 g/min. Daily dust settlement ranged between 40 and 300 g/m/sup 2/. Total quantity of accumulated coal dust in the power plant ranged from 0.8-650 kg/day; 250 g/m/sup 3/ of coal dust may cause an explosion. Thus, a dangerous amount of coal dust, depending on work-site, will settle in 3.3.-21.8 days. Disturbance of settled dust may create explodable clouds. Details of measurements taken and data evaluation are included. 4 refs.

DHS small-scale safety and thermal testing of improvised explosives-comparison of testing performance

International Nuclear Information System (INIS)

Reynolds, J G; Hsu, P C; Sandstrom, M M; Brown, G W; Warner, K F; Phillips, J J; Shelley, T J; Reyes, J A

2014-01-01

One of the first steps in establishing safe handling procedures for explosives is small-scale safety and thermal (SSST) testing. To better understand the response of improvised materials or homemade explosives (HMEs) to SSST testing, 16 HME materials were compared to three standard military explosives in a proficiency-type round robin study among five laboratories-two DoD and three DOE-sponsored by DHS. The testing matrix has been designed to address problems encountered with improvised materials-powder mixtures, liquid suspensions, partially wetted solids, immiscible liquids, and reactive materials. More than 30 issues have been identified that indicate standard test methods may require modification when applied to HMEs to derive accurate sensitivity assessments needed for developing safe handling and storage practices. This paper presents a generalized comparison of the results among the testing participants, comparison of friction results from BAM (German Bundesanstalt für Materi-alprüfung) and ABL (Allegany Ballistics Laboratory) designed testing equipment, and an overview of the statistical results from the RDX (1,3,5-Trinitroperhydro-1,3,5-triazine) standard tested throughout the proficiency test.

Comparison of the Effects of Thermal Pretreatment, Steam Explosion and Ultrasonic Disintegration on Digestibility of Corn Stover

Directory of Open Access Journals (Sweden)

Andras Dallos

2016-06-01

Full Text Available The energy demand of the corn-based bioethanol production could be reduced using the agricultural byproducts as bioenergy feedstock for biogas digesters. The release of lignocellulosic material and therefore the acceleration of degradation processes can be achieved using thermal and mechanical pretreatments, which assist to hydrolyze the cell walls and speed the solubilization of biopolymers in biogas feedstock. This study is focused on liquid hot water, steam explosion and ultrasonic pretreatments of corn stover. The scientific contribution of this paper is a comprehensive comparison of the performance of the pretreatments by fast analytical, biochemical, anaerobic digestibility and biomethane potential tests, extended by energy consumptions and energy balance calculations.The effectiveness of pretreatments was evaluated by means of soluble chemical oxygen demand, biochemical oxygen demand and by the biogas and methane productivities. The results have shown that the thermal pretreatment, steam explosion and ultrasonic irradiation of biogas feedstock disintegrated the lignocellulosic structure, increased and accelerated the methane production and increased the cumulative biogas and methane productivity of corn stover in reference to the control during mesophilic anaerobic digestion.The energy balance demonstrated that there is an economical basis of the application of the liquid hot-compressed water pretreatments in a biogas plant. However, the steam explosion and ultrasonication are energetically not profitable for corn stover pretreatment.

A Novel Design of Rescue Capsule considering the Pressure Characteristics and Thermal Dynamic Response with Thermomechanical Coupling Action Subjected to Gas Explosion Load

Directory of Open Access Journals (Sweden)

Xiaowei Zhai

2017-01-01

Full Text Available To ensure the structural safety and reliability of coal mine rescue capsule in disastrous surroundings after gas explosion, in this paper, the thermomechanical coupling effect on a certain structure subjected to gas explosion was analyzed, and then a novel rescue capsule with a combination of radius and square features was designed according to the underground surroundings and relevant regulations on mine rescue devices. Foremost, the coupling mechanism of thermal-fluid-solid interaction between gas explosion shock wave and rescue capsule and the thermal dynamic response of the capsule subjected to explosion load of gas/air mixture was investigated and revealed by employing LS-DYNA. The variation laws and characteristics of stress field, displacement field, and temperature field of the capsule were analyzed based on the simulation results. Results show that the structural safety, tightness, and reliability of the capsule meet the requirements of the national safety regulations. The design method presented in this work provides a new thought for design of coal mine rescue capsule.

Propagation of Reactions in Thermally-damaged PBX-9501

Energy Technology Data Exchange (ETDEWEB)

Tringe, J W; Glascoe, E A; Kercher, J R; Willey, T M; Springer, H K; Greenwood, D W; Molitoris, J D; Smilowitz, L; Henson, B F; Maienschein, J L

2010-03-05

A thermally-initiated explosion in PBX-9501 (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine) is observed in situ by flash x-ray imaging, and modeled with the LLNL multi-physics arbitrary-Lagrangian-Eulerian code ALE3D. The containment vessel deformation provides a useful estimate of the reaction pressure at the time of the explosion, which we calculate to be in the range 0.8-1.4 GPa. Closely-coupled ALE3D simulations of these experiments, utilizing the multi-phase convective burn model, provide detailed predictions of the reacted mass fraction and deflagration front acceleration. During the preinitiation heating phase of these experiments, the solid HMX portion of the PBX-9501 undergoes a {beta}-phase to {delta}-phase transition which damages the explosive and induces porosity. The multi-phase convective burn model results demonstrate that damaged particle size and pressure are critical for predicting reaction speed and violence. In the model, energetic parameters are taken from LLNL's thermochemical-kinetics code Cheetah and burn rate parameters from Son et al. (2000). Model predictions of an accelerating deflagration front are in qualitative agreement with the experimental images assuming a mode particle diameter in the range 300-400 {micro}m. There is uncertainty in the initial porosity caused by thermal damage of PBX-9501 and, thus, the effective surface area for burning. To better understand these structures, we employ x-ray computed tomography (XRCT) to examine the microstructure of PBX-9501 before and after thermal damage. Although lack of contrast between grains and binder prevents the determination of full grain size distribution in this material, there are many domains visible in thermally damaged PBX-9501 with diameters in the 300-400 {micro}m range.

The evolution of solid density within a thermal explosion II. Dynamic proton radiography of cracking and solid consumption by burning

International Nuclear Information System (INIS)

Smilowitz, L.; Henson, B. F.; Romero, J. J.; Asay, B. W.; Saunders, A.; Merrill, F. E.; Morris, C. L.; Kwiatkowski, K.; Grim, G.; Mariam, F.; Schwartz, C. L.; Hogan, G.; Nedrow, P.; Murray, M. M.; Thompson, T. N.; Espinoza, C.; Lewis, D.; Bainbridge, J.; McNeil, W.; Rightley, P.

2012-01-01

We report proton transmission images obtained subsequent to the laser assisted thermal ignition of a sample of PBX 9501 (a plastic bonded formulation of the explosive nitramine octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX)). We describe the laser assisted thermal ignition technique as a means to synchronize a non-linear thermal ignition event while preserving the subsequent post-ignition behavior. We have obtained dynamic proton transmission images at two spatial magnifications and viewed both the radial and transverse axis of a solid cylindrical sample encased in aluminum. Images have been obtained with 3 to 15 μs temporal resolution and approximately 100 μm spatial resolution at the higher magnification. We observe case expansion from very early in the experiment, until case fragmentation. We observe spatially anisotropic features in the transmission which we attribute to cracking in the solid explosive, in agreement with previous measurements conducted on two dimensional samples with optical viewing. Digital analysis of the images also reveals spatially isotropic features which we attribute to the evolution of the loss of density by burning subsequent to thermal ignition.

The evolution of solid density within a thermal explosion II. Dynamic proton radiography of cracking and solid consumption by burning

Energy Technology Data Exchange (ETDEWEB)

Smilowitz, L.; Henson, B. F.; Romero, J. J.; Asay, B. W.; Saunders, A.; Merrill, F. E.; Morris, C. L.; Kwiatkowski, K.; Grim, G.; Mariam, F.; Schwartz, C. L.; Hogan, G.; Nedrow, P.; Murray, M. M.; Thompson, T. N.; Espinoza, C.; Lewis, D.; Bainbridge, J.; McNeil, W.; Rightley, P. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); and others

2012-05-15

We report proton transmission images obtained subsequent to the laser assisted thermal ignition of a sample of PBX 9501 (a plastic bonded formulation of the explosive nitramine octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX)). We describe the laser assisted thermal ignition technique as a means to synchronize a non-linear thermal ignition event while preserving the subsequent post-ignition behavior. We have obtained dynamic proton transmission images at two spatial magnifications and viewed both the radial and transverse axis of a solid cylindrical sample encased in aluminum. Images have been obtained with 3 to 15 {mu}s temporal resolution and approximately 100 {mu}m spatial resolution at the higher magnification. We observe case expansion from very early in the experiment, until case fragmentation. We observe spatially anisotropic features in the transmission which we attribute to cracking in the solid explosive, in agreement with previous measurements conducted on two dimensional samples with optical viewing. Digital analysis of the images also reveals spatially isotropic features which we attribute to the evolution of the loss of density by burning subsequent to thermal ignition.

Thermal-hydraulics of wave propagation and pressure distribution under hypothetical steam explosion conditions in the ANS reactor

Energy Technology Data Exchange (ETDEWEB)

Taleyarkhan, R.P.; Georgevich, V.; N-Valenit, S.; Kim, S.H. [Oak Ridge National Lab., TN (United States)

1995-09-01

This paper describes salient aspects of the modeling and analysis framework for evaluation of dynamic loads, wave propagation, and pressure distributions (under hypothetical steam explosion conditions) around key structural boundaries of the Advanced Neutron Source (ANS) reactor core region. A staged approach was followed, using simple thermodynamic models for bounding loads and the CTH code for evaluating realistic estimates in a staged multidimensional framework. Effects of nodalization, melt dispersal into coolant during explosion, single versus multidirectional dissipation, energy level of melt, and rate of energy deposition into coolant were studied. The importance of capturing multidimensional effects that simultaneously account for fluid-structural interactions was demonstrated. As opposed to using bounding loads from thermodynamic evaluations, it was revealed that the ANS reactor system will not be vulnerable to vertically generated missiles that threaten containment if realistic estimates of energetics are used (from CTH calculations for thermally generated steam explosions without significant aluminum ignition).

Improve the Anaerobic Biodegradability by Copretreatment of Thermal Alkali and Steam Explosion of Lignocellulosic Waste

Directory of Open Access Journals (Sweden)

Muhammad Abdul Hanan Siddhu

2016-01-01

Full Text Available Effective alteration of the recalcitrance properties like crystallization of cellulose, lignin shield, and interlinking of lignocellulosic biomass is an ideal way to utilize the full-scale potential for biofuel production. This study exhibited three different pretreatment effects to enhance the digestibility of corn stover (CS for methane production. In this context, steam explosion (SE and thermal potassium hydroxide (KOH-60°C treated CS produced the maximal methane yield of 217.5 and 243.1 mL/gvs, which were 40.0% and 56.4% more than untreated CS (155.4 mL/gvs, respectively. Copretreatment of thermal potassium hydroxide and steam explosion (CPTPS treated CS was highly significant among all treatments and improved 88.46% (292.9 mL/gvs methane yield compared with untreated CS. Besides, CPTPS also achieved the highest biodegradability up to 68.90%. Three kinetic models very well simulated dynamics of methane production yield. Moreover, scanning electron microscopy (SEM, Fourier transform infrared (FTIR, and X-ray diffraction (XRD analyses declared the most effective changes in physicochemical properties after CPTPS pretreatment. Thus, CPTPS might be a promising approach to deconstructing the recalcitrance of lignocellulosic structure to improve the biodegradability for AD.

ECO steam explosion experiments on the conversion of thermal into mechanical energy

International Nuclear Information System (INIS)

Cherdron, W.; Kaiser, A.; Schuetz, W.; Will, H.

2001-01-01

In case of a steam explosion, e.g. as a consequence of a severe reactor accident, part of the thermal energy of the melt is transferred into mechanical energy. At Forschungszentrum Karlsruhe, so-called ECO experiments, are being directed to measure the conversion factor under well-defined conditions. In ECO, alumina from a thermite reaction is used as a simulating material instead of corium. Dimensions of the test facility as well as major test conditions, e.g. temperature and release mode of the melt, water inventory and test procedure, are based on the former PREMIX experimental series. In the paper, results of the first test, ECO 01, are given. (orig.)

CFD analysis of gas explosions vented through relief pipes.

Science.gov (United States)

Ferrara, G; Di Benedetto, A; Salzano, E; Russo, G

2006-09-21

Vent devices for gas and dust explosions are often ducted to safe locations by means of relief pipes. However, the presence of the duct increases the severity of explosion if compared to simply vented vessels (i.e. compared to cases where no duct is present). Besides, the identification of the key phenomena controlling the violence of explosion has not yet been gained. Multidimensional models coupling, mass, momentum and energy conservation equations can be valuable tools for the analysis of such complex explosion phenomena. In this work, gas explosions vented through ducts have been modelled by a two-dimensional (2D) axi-symmetric computational fluid dynamic (CFD) model based on the unsteady Reynolds Averaged Navier Stokes (RANS) approach in which the laminar, flamelet and distributed combustion models have been implemented. Numerical test have been carried out by varying ignition position, duct diameter and length. Results have evidenced that the severity of ducted explosions is mainly driven by the vigorous secondary explosion occurring in the duct (burn-up) rather than by the duct flow resistance or acoustic enhancement. Moreover, it has been found out that the burn-up affects explosion severity due to the reduction of venting rate rather than to the burning rate enhancement through turbulization.

Modeling of composite synthesis in conditions of controlled thermal explosion

Science.gov (United States)

Kukta, Yaroslav; Knyazeva, Anna

2017-12-01

The paper proposes the model for the titanium-based composite synthesis from powders of titanium and carbon of non-stoichiometric composition. The model takes into account the mixture heating from chamber walls, the dependence of liquidus and solidus temperatures on the composition of reacting mixture and the formation of possible irreversible phases. The reaction retardation by the reaction product is taken into consideration in kinetic laws. As an example, the results of temperature and conversion level calculation are presented for the system Ti-C with the summary reaction for different temperatures of chamber walls heating. It was revealed that the reaction retardation being the reaction product can be the cause of incomplete conversion in the thermal explosion conditions. Non-stoichiometric composition leads to the conditions of degenerated mode when some additional heating is necessary to complete the reaction.

Shock Initiation of Damaged Explosives

Energy Technology Data Exchange (ETDEWEB)

Chidester, S K; Vandersall, K S; Tarver, C M

2009-10-22

Explosive and propellant charges are subjected to various mechanical and thermal insults that can increase their sensitivity over the course of their lifetimes. To quantify this effect, shock initiation experiments were performed on mechanically and thermally damaged LX-04 (85% HMX, 15% Viton by weight) and PBX 9502 (95% TATB, 5% Kel-F by weight) to obtain in-situ manganin pressure gauge data and run distances to detonation at various shock pressures. We report the behavior of the HMX-based explosive LX-04 that was damaged mechanically by applying a compressive load of 600 psi for 20,000 cycles, thus creating many small narrow cracks, or by cutting wedge shaped parts that were then loosely reassembled, thus creating a few large cracks. The thermally damaged LX-04 charges were heated to 190 C for long enough for the beta to delta solid - solid phase transition to occur, and then cooled to ambient temperature. Mechanically damaged LX-04 exhibited only slightly increased shock sensitivity, while thermally damaged LX-04 was much more shock sensitive. Similarly, the insensitive explosive PBX 9502 was mechanically damaged using the same two techniques. Since PBX 9502 does not undergo a solid - solid phase transition but does undergo irreversible or 'rachet' growth when thermally cycled, thermal damage to PBX 9502 was induced by this procedure. As for LX-04, the thermally damaged PBX 9502 demonstrated a greater shock sensitivity than mechanically damaged PBX 9502. The Ignition and Growth reactive flow model calculated the increased sensitivities by igniting more damaged LX-04 and PBX 9502 near the shock front based on the measured densities (porosities) of the damaged charges.

An Analysis of the Initiation Process of Electro-Explosive Devices

Directory of Open Access Journals (Sweden)

Paulo Cesar de Carvalho Faria

2012-03-01

Full Text Available Electro-explosive devices (an electric resistance encapsulated by a primary explosive fundamentally convert electrical energy into thermal energy, to start off an explosive chemical reaction. Obviously, the activation of those devices shall not happen by accident or, even worse, by intentional exogenous influence. From an ordinary differential equation, which describes the electro-explosive thermal behavior, a remarkable, but certainly not intuitive, dependence of the temperature response on the time constant of the heat transfer process is verified: the temperature profile dramatically changes as the time constant spans a wide range of values, from much lesser than the pulse width to much greater than the pulse period. Based on this dependence, important recommendations, concerning the efficient and safety operation of electro-explosive devices, are proposed.

Study on Thermal Decomposition Characteristics of Ammonium Nitrate Emulsion Explosive in Different Scales

Science.gov (United States)

Wu, Qiujie; Tan, Liu; Xu, Sen; Liu, Dabin; Min, Li

2018-04-01

Numerous accidents of emulsion explosive (EE) are attributed to uncontrolled thermal decomposition of ammonium nitrate emulsion (ANE, the intermediate of EE) and EE in large scale. In order to study the thermal decomposition characteristics of ANE and EE in different scales, a large-scale test of modified vented pipe test (MVPT), and two laboratory-scale tests of differential scanning calorimeter (DSC) and accelerating rate calorimeter (ARC) were applied in the present study. The scale effect and water effect both play an important role in the thermal stability of ANE and EE. The measured decomposition temperatures of ANE and EE in MVPT are 146°C and 144°C, respectively, much lower than those in DSC and ARC. As the size of the same sample in DSC, ARC, and MVPT successively increases, the onset temperatures decrease. In the same test, the measured onset temperature value of ANE is higher than that of EE. The water composition of the sample stabilizes the sample. The large-scale test of MVPT can provide information for the real-life operations. The large-scale operations have more risks, and continuous overheating should be avoided.

Violence Patterns in Peckinpah's The Wild Bunch (1969: Critical Reading

Directory of Open Access Journals (Sweden)

Baker Bani-Khair

2017-03-01

Full Text Available This paper focuses on the issue of violence in Sam Peckinpah's The Wild Bunch (1969 through explaining some of the cultural and historical implications of violence in the 1960s such as Vietnam War, the Mexican war and also the explosion of the feminist movement and some other important social and political upheavals that shaped the cultural context of the 1960s in America. It also sheds light on Sam Peckinpah’s approach of violence screen and stylizing violence and the representations of violence as a tormenting and brutalizing reality that matches the spirit of the age in addition to the social, political, and colonial conflicts of the 1960s. Violence and the implications of violence in The Wild Bunch whether social , cultural, psychological, or humanistic have been discussed in brief in order to show the critical approach of the film as being a rich and didactic film to watch, especially in terms of its rich cultural and historical contexts.

Contained fission explosion breeder reactor system

International Nuclear Information System (INIS)

Juhl, N.H.; Marwick, E.F.

1983-01-01

A reactor system for producing useful thermal energy and valuable isotopes, such as plutonium-239, uranium-233, and/or tritium, in which a pair of sub-critical masses of fissile and fertile actinide slugs are propelled into an ellipsoidal pressure vessel. The propelled slugs intercept near the center of the chamber where the concurring slugs become a more than prompt configuration thereby producing a fission explosion. Re-useable accelerating mechanisms are provided external of the vessel for propelling the slugs at predetermined time intervals into the vessel. A working fluid of lean molten metal slurry is injected into the chamber prior to each explosion for the attenuation of the explosion's effects, for the protection of the chamber's walls, and for the absorbtion of thermal energy and debris from the explosion. The working fluid is injected into the chamber in a pattern so as not to interfere with the flight paths of the slugs and to maximize the concentration of working fluid near the chamber's center. The heated working fluid is drained from the vessel and is used to perform useful work. Most of the debris from the explosion is collected as precipitate and is used for the manufacture of new slugs

Effects of magnesium-based hydrogen storage materials on the thermal decomposition, burning rate, and explosive heat of ammonium perchlorate-based composite solid propellant.

Science.gov (United States)

Liu, Leili; Li, Jie; Zhang, Lingyao; Tian, Siyu

2018-01-15

MgH 2 , Mg 2 NiH 4 , and Mg 2 CuH 3 were prepared, and their structure and hydrogen storage properties were determined through X-ray photoelectron spectroscopy and thermal analyzer. The effects of MgH 2 , Mg 2 NiH 4 , and Mg 2 CuH 3 on the thermal decomposition, burning rate, and explosive heat of ammonium perchlorate-based composite solid propellant were subsequently studied. Results indicated that MgH 2 , Mg 2 NiH 4 , and Mg 2 CuH 3 can decrease the thermal decomposition peak temperature and increase the total released heat of decomposition. These compounds can improve the effect of thermal decomposition of the propellant. The burning rates of the propellant increased using Mg-based hydrogen storage materials as promoter. The burning rates of the propellant also increased using MgH 2 instead of Al in the propellant, but its explosive heat was not enlarged. Nonetheless, the combustion heat of MgH 2 was higher than that of Al. A possible mechanism was thus proposed. Copyright © 2017. Published by Elsevier B.V.

Steam explosions in sodium cooled breeder reactors

International Nuclear Information System (INIS)

Lundell, B.

1982-01-01

Steam explosion is considered a physical process which transport heat from molten fuel to liquid coolant so fast that the coolant starts boiling in an explosion-like manner. The arising pressure waves transform part of the thermal energy to mechanical energy. This can stress the reactor tank and threaten its hightness. The course of the explosion has not been theoretical explained. Experimental results indicate that the probability of steam explosions in a breeder reactor is small. The efficiency of the transformation of the heat of fusion into mechanical energy in substantially lower than the theoretical maximum value. The mechanical stress from the steam explosion on the reactor tank does not seem to jeopardize its tightness. (G.B.)

Comparison of the Effects of Thermal Pretreatment, Steam Explosion and Ultrasonic Disintegration on Digestibility of Corn Stover

OpenAIRE

Andras Dallos; Gyula Dörgő; Dániel Capári

2016-01-01

The energy demand of the corn-based bioethanol production could be reduced using the agricultural byproducts as bioenergy feedstock for biogas digesters. The release of lignocellulosic material and therefore the acceleration of degradation processes can be achieved using thermal and mechanical pretreatments, which assist to hydrolyze the cell walls and speed the solubilization of biopolymers in biogas feedstock. This study is focused on liquid hot water, steam explosion and ultrasonic pretrea...

Nuclear explosions and their effects

Energy Technology Data Exchange (ETDEWEB)

1958-01-01

A brief historical background is given of the development of the atomic bomb. Also included is an account of the Hiroshima-Nagasaki bombing, plus some information on the testing and production of nuclear weapons by the United States, United Kingdom, and Russia. More detailed consideration is given to the following: the scientific principles of fission and fusion explosions; the energy released in fission and the radioactivity of fission products; blast, thermal, and radiologicalal effects of nuclear explosions; long-term radiological hazards from fall-out; and genetic effects of nuclear explosions. A brief account is given of the fission chain process, the concept of critical size, and the principles of implosion as applied to nuclear explosions. Limited information is presented on the controlled release of thermonuclear energy and catalyzed fusion reaction. Discussions are included on dose rates from radiation sources inside and outside the body, the effect of nuclear explosions on the weather, and the contamination of fish and marine organisms.

Steam explosion - physical foundations and relation to nuclear reactor safety

International Nuclear Information System (INIS)

Schumann, U.

1982-08-01

'Steam explosion' means the sudden evaporation of a fluid by heat exchange with a hotter material. Other terms are 'vapour explosion', 'thermal explosion', and 'energetic fuel-coolant interaction (FCI)'. In such an event a large fraction of the thermal energy initially stored in the hot material may possibly be converted into mechanical work. For pressurized water reactors one discusses (e.g. in risk analysis studies) a core melt-down accident during which molten fuel comes into contact with water. In the analysis of the consequences one has to investigate steam explosions. In this report an overview over the state of the knowledge is given. The overview is based on an extensive literature review. The objective of the report is to provide the basic knowledge which is required for understanding of the most important theories on the process of steam explosions. Following topics are treated: overview on steam explosion incidents, work potential, spontaneous nucleation, concept of detonation, results of some typical experiments, hydrodynamic fragmentation of drops, bubbles and jets, coarse mixtures, film-boiling, scenario of a core melt-down accident with possible steam-explosion in a pressurized water reactor. (orig.) [de

Investigation of the shallow depth explosions

International Nuclear Information System (INIS)

Kamegai, M.

1976-01-01

An investigation of the nuclear explosions at shallow depth is made. A combination of an explosion code and an effects code proves to be an excellent tool for this study. A numerical simulation of ''Johnie Boy'' shows that the energy coupling to the air takes place in two stages; first by a rising mound, and then by a vented source. The thermal effects are examined for a 1 kt source at three depths of burial. The ''mushroom effect'' leaves a hot radiative plasma in the upper level and cold materials in the lower region of the debris. The temperature and the energy density of the debris can give an upper limit on the thermal output

Risk of fire and dust explosions analysis in thermal Power station of ''As Pontes''; Analisis del Riesgo de fuego y Explosion en la Central Termica As Pontes

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

Among the numerous difficulties come up in the industrial processes that operate with coal, the handling of combustible solids constitutes a priority objective because of the potential risk of fire and dust explosions that implies. The aim of this project was to determine the coal usage conditions that assure total safety in its manipulation avoiding every risks at the Thermal Power Station. Several variables had to be considered starting with the basis concept of coal, which ranges very different types, compositions and origins and studying the coal handling and operation condition on different areas in the Thermal Power Station. (Author)

Perceptions of television violence: effects of programme genre and type of violence on viewers' judgements of violent portrayals.

Science.gov (United States)

Gunter, B; Furnham, A

1984-06-01

This paper reports two studies which examined the mediating effects of programme genre and physical form of violence on viewers' perceptions of violent TV portrayals. In Expt 1, a panel of British viewers saw portrayals from five programme genres: British crime-drama series, US crime-drama series, westerns, science-fiction series and cartoons which feature either fights or shootings. In Expt. 2, the same viewers rated portrayals from British crime-drama and westerns which featured four types of violence, fist-fights, shootings, stabbings and explosions. All scenes were rated along eight unipolar scales. Panel members also completed four subscales of a personal hostility inventory. Results showed that both fictional setting and physical form had significant effects on viewers' perceptions of televised violence. British crime-drama portrayals, and portrayals that featured shootings and stabbings, were rated as most violent and disturbing. Also, there were strong differences between viewers with different self-reported propensities towards either verbal or physical aggression. More physically aggressive individuals tended to perceive physical unarmed violence as less violent than did more verbally aggressive types.

Thermal Decomposition of Nitrated Tributyl Phosphate

International Nuclear Information System (INIS)

Paddleford, D.F.; Hou, Y.; Barefield, E.K.; Tedder, D.W.; Abdel-Khalik, S.I.

1995-01-01

Contact between tributyl phosphate and aqueous solutions of nitric acid and/or heavy metal nitrate salts at elevated temperatures can lead to exothermic reactions of explosive violence. Even though such operations have been routinely performed safely for decades as an intrinsic part of the Purex separation processes, several so-called ''red oil'' explosions are known to have occurred in the United States, Canada, and the former Soviet Union. The most recent red oil explosion occurred at the Tomsk-7 separations facility in Siberia, in April 1993. That explosion destroyed part of the unreinforced masonry walls of the canyon-type building in which the process was housed, and allowed the release of a significant quantity of radioactive material

High-throughput trace analysis of explosives in water by laser diode thermal desorption/atmospheric pressure chemical ionization-tandem mass spectrometry.

Science.gov (United States)

Badjagbo, Koffi; Sauvé, Sébastien

2012-07-03

Harmful explosives can accumulate in natural waters in the long term during their testing, usage, storage, and dumping and can pose a health risk to humans and the environment. For the first time, attachment of small anions to neutral molecules in laser diode thermal desorption/atmospheric pressure chemical ionization was systematically investigated for the direct determination of trace nitroaromatics, nitrate esters, and nitramine explosives in water. Using ammonium chloride as an additive improved the instrument response for all the explosives tested and promoted the formation of several characteristic adduct ions. The method performs well achieving good linearity over at least 2 orders of magnitude, with coefficients of determination greater than 0.995. The resulting limits of detection are in the range of 0.009-0.092 μg/L. River water samples were successfully analyzed by the proposed method with accuracy in the range of 96-98% and a response time of 15 s, without any further pretreatment or chromatographic separation.

Differential thermal analysis microsystem for explosive detection

DEFF Research Database (Denmark)

Olsen, Jesper Kenneth; Greve, Anders; Senesac, L.

2011-01-01

as a small silicon nitride membrane incorporating heater elements and a temperature measurement resistor. In this manuscript the DTA system is described and tested by measuring calorimetric response of 3 different kinds of explosives (TNT, RDX and PETN). This project is carried out under the framework...

Thermal hazard assessment of AN and AN-based explosives

Energy Technology Data Exchange (ETDEWEB)

Turcotte, T.; Lightfoot, P. D.; Fouchard, R.; Jones, D. E. G. [Natural Resources Canada, CANMET Canadian Explosives Research Laboratory, Ottawa, ON (Canada)

2002-12-01

Ammonium-based aqeous solutions of various concentrations are processed in both the fertilizer and explosives industry, and ammonium nitrate emulsions form the basis of bulk ammonium nitrate emulsion explosives. Major accidents involving overheating of large quantities of these products are not uncommon. To provide guidance to handling large bulk quantities of these materials laboratory experiments must be carried out in such a way as to minimize heat losses from the samples. In this study experiments were performed on pure ammonium, the popular commercial explosive ANFO, various aqueous ammonium solutions and typical bulk and packaged ammonium nitrate emulsions, using two laboratory-scale calorimeters (accelerating rate calorimeter and adiabatic Dewar calorimeter). The objective of the experiments was to study the effects of sample mass, atmosphere, and formulation on the resulting onset temperatures. Result from the two techniques were compared and a method for extrapolating these results to large-scale inventories was proposed. 22 refs., 4 tabs., 14 figs.

Rapid thermal process by RF heating of nano-graphene layer/silicon substrate structure: Heat explosion theory approach

Science.gov (United States)

Sinder, M.; Pelleg, J.; Meerovich, V.; Sokolovsky, V.

2018-03-01

RF heating kinetics of a nano-graphene layer/silicon substrate structure is analyzed theoretically as a function of the thickness and sheet resistance of the graphene layer, the dimensions and thermal parameters of the structure, as well as of cooling conditions and of the amplitude and frequency of the applied RF magnetic field. It is shown that two regimes of the heating can be realized. The first one is characterized by heating of the structure up to a finite temperature determined by equilibrium between the dissipated loss power caused by induced eddy-currents and the heat transfer to environment. The second regime corresponds to a fast unlimited temperature increase (heat explosion). The criterions of realization of these regimes are presented in the analytical form. Using the criterions and literature data, it is shown the possibility of the heat explosion regime for a graphene layer/silicon substrate structure at RF heating.

Thermal explosion hazards on 18650 lithium ion batteries with a VSP2 adiabatic calorimeter

Energy Technology Data Exchange (ETDEWEB)

Jhu, Can-Yong [Doctoral Program, Graduate School of Engineering Science and Technology, National Yunlin University of Science and Technology (NYUST), 123, University Rd., Sec. 3, Douliou, Yunlin 64002, Taiwan, ROC (China); Wang, Yih-Wen, E-mail: g9410825@yuntech.edu.tw [Department of Occupational Safety and Health, Jen-Teh Junior College of Medicine, Nursing and Management, 79-9, Sha-Luen-Hu, Xi-Zhou-Li, Houlong, Miaoli 35664, Taiwan, ROC (China); Shu, Chi-Min [Doctoral Program, Graduate School of Engineering Science and Technology, National Yunlin University of Science and Technology (NYUST), 123, University Rd., Sec. 3, Douliou, Yunlin 64002, Taiwan, ROC (China); Chang, Jian-Chuang; Wu, Hung-Chun [Material and Chemical Research Laboratories, Industrial Technology Research Institute (ITRI), Rm. 222, Bldg. 77, 2F, 195, Sec. 4, Chung Hsing Rd., Chutung, Hsinchu 31040, Taiwan, ROC (China)

2011-08-15

Thermal abuse behaviors relating to adiabatic runaway reactions in commercial 18650 lithium ion batteries (LiCoO{sub 2}) are being studied in an adiabatic calorimeter, vent sizing package 2 (VSP2). We select four worldwide battery producers, Sony, Sanyo, Samsung and LG, and tested their Li-ion batteries, which have LiCoO{sub 2} cathodes, to determine their thermal instabilities and adiabatic runaway features. The charged (4.2 V) and uncharged (3.7 V) 18650 Li-ion batteries are tested using a VSP2 with a customized stainless steel test can to evaluate their thermal hazard characteristics, such as the initial exothermic temperature (T{sub 0}), the self-heating rate (dT/dt), the pressure rise rate (dP/dt), the pressure-temperature profiles and the maximum temperature (T{sub max}) and pressure (P{sub max}). The T{sub max} and P{sub max} of the charged Li-ion battery during the runaway reaction reach 903.0 {sup o}C and 1565.9 psig (pound-force per square inch gauge), respectively. This result leads to a thermal explosion, and the heat of reaction is 26.2 kJ. The thermokinetic parameters of the reaction of LiCoO{sub 2} batteries are also determined using the Arrhenius model. The thermal reaction mechanism of the Li-ion battery (pack) proved to be an important safety concern for energy storage. Additionally, use of the VSP2 to classify the self-reactive ratings of the various Li-ion batteries demonstrates a new application of the adiabatic calorimetric methodology.

Thermal explosion hazards on 18650 lithium ion batteries with a VSP2 adiabatic calorimeter

International Nuclear Information System (INIS)

Jhu, Can-Yong; Wang, Yih-Wen; Shu, Chi-Min; Chang, Jian-Chuang; Wu, Hung-Chun

2011-01-01

Thermal abuse behaviors relating to adiabatic runaway reactions in commercial 18650 lithium ion batteries (LiCoO 2 ) are being studied in an adiabatic calorimeter, vent sizing package 2 (VSP2). We select four worldwide battery producers, Sony, Sanyo, Samsung and LG, and tested their Li-ion batteries, which have LiCoO 2 cathodes, to determine their thermal instabilities and adiabatic runaway features. The charged (4.2 V) and uncharged (3.7 V) 18650 Li-ion batteries are tested using a VSP2 with a customized stainless steel test can to evaluate their thermal hazard characteristics, such as the initial exothermic temperature (T 0 ), the self-heating rate (dT/dt), the pressure rise rate (dP/dt), the pressure-temperature profiles and the maximum temperature (T max ) and pressure (P max ). The T max and P max of the charged Li-ion battery during the runaway reaction reach 903.0 o C and 1565.9 psig (pound-force per square inch gauge), respectively. This result leads to a thermal explosion, and the heat of reaction is 26.2 kJ. The thermokinetic parameters of the reaction of LiCoO 2 batteries are also determined using the Arrhenius model. The thermal reaction mechanism of the Li-ion battery (pack) proved to be an important safety concern for energy storage. Additionally, use of the VSP2 to classify the self-reactive ratings of the various Li-ion batteries demonstrates a new application of the adiabatic calorimetric methodology.

Explosion characteristics of synthesised biogas at various temperatures.

Science.gov (United States)

Dupont, L; Accorsi, A

2006-08-25

Biogas is considered as a valuable source of renewable energy. Indeed, it can be turned into useful energy (heat, electricity, fuel) and can contribute to reduce greenhouse gas emissions. Knowledge of its safety characteristics is a very important practical issue. Experimental investigation of synthesised biogas explosion characteristics was conducted in a 20-L sphere at various temperatures (30-70 degrees C) and at atmospheric pressure. The studied biogas was made of 50% methane (CH(4)) and 50% carbon dioxide (CO(2)). It was also saturated with humidity: this composition is frequently met in digesters during waste methanisation. There are two inert gases in biogas: water vapour and carbon dioxide. Its vapour water content rises along with temperature. The presence of these inert gases modifies considerably biogas characteristics compared to the ones of pure methane: explosion limits are lowered and beyond 70 degrees C, water vapour content is sufficient to inert the mixture. Furthermore, explosion violence (estimated with the maximum rate of pressure rise values, (dp/dt)(max)) is three times lower for biogas than for pure methane at ambient temperature.

Explosion characteristics of synthesised biogas at various temperatures

Energy Technology Data Exchange (ETDEWEB)

Dupont, L. [Institut National de l' Environnement Industriel et des Risques, Parc Technologique Alata, BP2, Verneuil-en-Halatte (France)]. E-mail: laurent.dupont@ineris.fr; Accorsi, A. [Institut National de l' Environnement Industriel et des Risques, Parc Technologique Alata, BP2, Verneuil-en-Halatte (France)]. E-mail: antoinette.accorsi@ineris.fr

2006-08-25

Biogas is considered as a valuable source of renewable energy. Indeed, it can be turned into useful energy (heat, electricity, fuel) and can contribute to reduce greenhouse gas emissions. Knowledge of its safety characteristics is a very important practical issue. Experimental investigation of synthesised biogas explosion characteristics was conducted in a 20-L sphere at various temperatures (30-70deg. C) and at atmospheric pressure. The studied biogas was made of 50% methane (CH{sub 4}) and 50% carbon dioxide (CO{sub 2}). It was also saturated with humidity: this composition is frequently met in digesters during waste methanisation. There are two inert gases in biogas: water vapour and carbon dioxide. Its vapour water content rises along with temperature. The presence of these inert gases modifies considerably biogas characteristics compared to the ones of pure methane: explosion limits are lowered and beyond 70deg. C, water vapour content is sufficient to inert the mixture. Furthermore, explosion violence (estimated with the maximum rate of pressure rise values (dp/dt){sub max}) is three times lower for biogas than for pure methane at ambient temperature.

Explosion characteristics of synthesised biogas at various temperatures

International Nuclear Information System (INIS)

Dupont, L.; Accorsi, A.

2006-01-01

Biogas is considered as a valuable source of renewable energy. Indeed, it can be turned into useful energy (heat, electricity, fuel) and can contribute to reduce greenhouse gas emissions. Knowledge of its safety characteristics is a very important practical issue. Experimental investigation of synthesised biogas explosion characteristics was conducted in a 20-L sphere at various temperatures (30-70deg. C) and at atmospheric pressure. The studied biogas was made of 50% methane (CH 4 ) and 50% carbon dioxide (CO 2 ). It was also saturated with humidity: this composition is frequently met in digesters during waste methanisation. There are two inert gases in biogas: water vapour and carbon dioxide. Its vapour water content rises along with temperature. The presence of these inert gases modifies considerably biogas characteristics compared to the ones of pure methane: explosion limits are lowered and beyond 70deg. C, water vapour content is sufficient to inert the mixture. Furthermore, explosion violence (estimated with the maximum rate of pressure rise values (dp/dt) max ) is three times lower for biogas than for pure methane at ambient temperature

Steam explosions in light water reactors

International Nuclear Information System (INIS)

1981-01-01

The report deals with a postulated accident caused by molten fuel falling into the lower plenum of the containment of a reactor. The analysis which is presented in the report shows that the thermal energy released in the resulting steam explosion is not enough to destroy the pressure vessel or the containment. The report was prepared for the Swedish Governmental Committee on steam explosion in light water reactors. It includes statements issued by internationally well-known specialists. (G.B.)

Green primary explosives: 5-nitrotetrazolato-N2-ferrate hierarchies.

Science.gov (United States)

Huynh, My Hang V; Coburn, Michael D; Meyer, Thomas J; Wetzler, Modi

2006-07-05

The sensitive explosives used in initiating devices like primers and detonators are called primary explosives. Successful detonations of secondary explosives are accomplished by suitable sources of initiation energy that is transmitted directly from the primaries or through secondary explosive boosters. Reliable initiating mechanisms are available in numerous forms of primers and detonators depending upon the nature of the secondary explosives. The technology of initiation devices used for military and civilian purposes continues to expand owing to variations in initiating method, chemical composition, quantity, sensitivity, explosive performance, and other necessary built-in mechanisms. Although the most widely used primaries contain toxic lead azide and lead styphnate, mixtures of thermally unstable primaries, like diazodinitrophenol and tetracene, or poisonous agents, like antimony sulfide and barium nitrate, are also used. Novel environmentally friendly primary explosives are expanded here to include cat[Fe(II)(NT)(3)(H(2)O)(3)], cat(2)[Fe(II)(NT)(4)(H(2)O)(2)], cat(3)[Fe(II)(NT)(5)(H(2)O)], and cat(4)[Fe(II)(NT)(6)] with cat = cation and NT(-) = 5-nitrotetrazolato-N(2). With available alkaline, alkaline earth, and organic cations as partners, four series of 5-nitrotetrazolato-N(2)-ferrate hierarchies have been prepared that provide a plethora of green primaries with diverse initiating sensitivity and explosive performance. They hold great promise for replacing not only toxic lead primaries but also thermally unstable primaries and poisonous agents. Strategies are also described for the systematic preparation of coordination complex green primaries based on appropriate selection of ligands, metals, and synthetic procedures. These strategies allow for maximum versatility in initiating sensitivity and explosive performance while retaining properties required for green primaries.

Differences in coupling between chemical and nuclear explosions

International Nuclear Information System (INIS)

Glenn, L.A.

1992-01-01

The teleseismic amplitude resulting from an underground explosion is proportional to the asymptotic value of the reduced displacement potential (φ∞) or, in physical terms, to the permanent change in volume measured anywhere beyond the range at which the outgoing wave has become elastic. φ∞ decreases with increasing initial cavity size (r o ) until the cavity is large enough to preclude inelastic behavior in the surrounding rock, at which point no further decrease occurs. With nuclear explosions, φ∞ can also be reduced by decreasing the initial cavity size over a certain range. This occurs because, in this range of r 0 W -1/3 (where W is the yield) the thermal pressure in the surrounding medium increases much more slowly than does the thermal energy. With chemical explosions, by contrast, r 0 W -1/3 cannot be decreased below the fully tamped limit because the energy density is bounded above. Moreover, for the most of the cavity expansion period the ratio of specific heats of the chemical explosion products is substantially higher than the equivalent ratio in a nuclear explosion, so that the cavity pressure in the former case is higher as well and this further amplifies the differences between the two. Calculations show that the teleseismic amplitude could be as much as 50% higher for an equivalent tamped chemical explosion in salt than was observed in the SALMON nuclear event

Internal sub-sonic burning during an explosion viewed via dynamic X-ray radiography

Science.gov (United States)

Smilowitz, L.; Henson, B. F.; Oschwald, D.; Suvorova, N.; Remelius, D.

2017-10-01

We observe internal convective and conductive burn front propagation and solid consumption subsequent to thermal ignition for plastic bonded formulations of the solid organic secondary explosives octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine and 1,3,5-triamino-2,4,6-trinitrobenzene. This work describes x-ray radiographic diagnostics enabling the study of solid density in a fully encased explosive during internal burning subsequent to ignition. The result of this study is the ability to directly observe and measure rates of energy release during a thermal explosion.

Crippling Violence: Conflict and Incident Polio in Afghanistan.

Science.gov (United States)

Norris, Alison; Hachey, Kevin; Curtis, Andrew; Bourdeaux, Margaret

2016-01-01

Designing effective public health campaigns in areas of armed conflict requires a nuanced understanding of how violence impacts the epidemiology of the disease in question. We examine the geographical relationship between violence (represented by the location of detonated Improvised Explosive Devices) and polio incidence by generating maps of IEDs and polio incidence during 2010, and by comparing the mean number of IED detonations in polio high-risk districts with non polio high-risk districts during 2004-2009. We demonstrate a geographic relationship between IED violence and incident polio. Districts that have high-risk for polio have highly statistically significantly greater mean numbers of IEDs than non polio high-risk districts (p-values 0.0010-0.0404). The geographic relationship between armed conflict and polio incidence provides valuable insights as to how to plan a vaccination campaign in violent contexts, and allows us to anticipate incident polio in the regions of armed conflict. Such information permits vaccination planners to engage interested armed combatants to co-develop strategies to mitigate the effects of violence on polio.

Crippling Violence: Conflict and Incident Polio in Afghanistan.

Directory of Open Access Journals (Sweden)

Alison Norris

Full Text Available Designing effective public health campaigns in areas of armed conflict requires a nuanced understanding of how violence impacts the epidemiology of the disease in question.We examine the geographical relationship between violence (represented by the location of detonated Improvised Explosive Devices and polio incidence by generating maps of IEDs and polio incidence during 2010, and by comparing the mean number of IED detonations in polio high-risk districts with non polio high-risk districts during 2004-2009.We demonstrate a geographic relationship between IED violence and incident polio. Districts that have high-risk for polio have highly statistically significantly greater mean numbers of IEDs than non polio high-risk districts (p-values 0.0010-0.0404.The geographic relationship between armed conflict and polio incidence provides valuable insights as to how to plan a vaccination campaign in violent contexts, and allows us to anticipate incident polio in the regions of armed conflict. Such information permits vaccination planners to engage interested armed combatants to co-develop strategies to mitigate the effects of violence on polio.

A case of intermittent explosive disorder

Directory of Open Access Journals (Sweden)

Amitabh Saha

2010-01-01

Full Text Available A case of impulse control disorder was observed and managed. In this case, the serving soldier of the Indian army presented with explosive outbursts of extreme violence and anger, which was not clearly directed. Following this act of aggression, he would experience a sense of gratification and relief. The episodes were recurrent and resulted in assaults or destruction of property. The aggression displayed was out of proportion to any perceived provocation and the individual felt increasing tension or arousal before committing the act. He did not have any feelings of regret, remorse or guilt about the behavior.

Modeling the thermal deformation of TATB-based explosives. Part 1: Thermal expansion of “neat-pressed” polycrystalline TATB

Energy Technology Data Exchange (ETDEWEB)

Luscher, Darby J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-05-08

We detail a modeling approach to simulate the anisotropic thermal expansion of polycrystalline (1,3,5-triamino-2,4,6-trinitrobenzene) TATB-based explosives that utilizes microstructural information including porosity, crystal aspect ratio, and processing-induced texture. This report, the first in a series, focuses on nonlinear thermal expansion of “neat-pressed” polycrystalline TATB specimens which do not contain any binder; additional complexities related to polymeric binder and irreversible ratcheting behavior are briefly discussed, however detailed investigation of these aspects are deferred to subsequent reports. In this work we have, for the first time, developed a mesoscale continuum model relating the thermal expansion of polycrystal TATB specimens to their microstructural characteristics. A self-consistent homogenization procedure is used to relate macroscopic thermoelastic response to the constitutive behavior of single-crystal TATB. The model includes a representation of grain aspect ratio, porosity, and crystallographic texture attributed to the consolidation process. A quantitative model is proposed to describe the evolution of preferred orientation of graphitic planes in TATB during consolidation and an algorithm constructed to develop a discrete representation of the associated orientation distribution function. Analytical and numerical solutions using this model are shown to produce textures consistent with previous measurements and characterization for isostatic and uniaxial “die-pressed” specimens. Predicted thermal strain versus temperature for textured specimens are shown to be in agreement with corresponding experimental measurements. Using the developed modeling approach, several simulations have been run to investigate the influence of microstructure on macroscopic thermal expansion behavior. Results from these simulations are used to identify qualitative trends. Implications of the identified trends are discussed in the context of

Mechanical efficiency of the energy release during a steam explosion

International Nuclear Information System (INIS)

Krieg, R.

1997-01-01

The mechanical processes during the expansion phase of a steam explosion with intimately fragmented liquid particles is investigated based on elementary principles and analytical solutions. During a short load pulse, the different densities of the water and the melted particles lead to different velocities. After the load pulse, viscosity effects lead to a slow down of the higher velocities and to a corresponding reconversion of the kinetic energy of the mixture into thermal energy. It is shown that both effects are proportional to each other. The ratio between the residual and the applied mechanical energy is defined as the mechanical efficiency of the steam explosion. Using data typical for a steam explosion in a pressurized water reactor, mechanical efficiencies of <50% are estimated. Considering that the thermodynamic efficiencies are quite limited, the very low conversion rates from thermal energy into mechanical energy observed during steam explosion experiments can be more easily understood

Thermochemistry of mixed explosives

International Nuclear Information System (INIS)

Janney, J.L.; Rogers, R.N.

1982-01-01

In order to predict thermal hazards of high-energy materials, accurate kinetics constants must be determined. Predictions of thermal hazards for mixtures of high-energy materials require measurements on the mixtures, because interactions among components are common. A differential-scanning calorimeter (DSC) can be used to observe rate processes directly, and isothermal methods enable detection of mechanism changes. Rate-controlling processes will change as components of a mixture are depleted, and the correct depletion function must be identified for each specific stage of a complex process. A method for kinetics measurements on mixed explosives can be demonstrated with Composition B is an approximately 60/40 mixture of RDX and TNT, and is an important military explosive. Kinetics results indicate that the mator process is the decomposition of RDX in solution in TNT with a perturbation caused by interaction between the two components. It is concluded that a combination of chemical kinetics and experimental self-heating procedures provides a good approach to the production of predictive models for thermal hazards of high-energy materials. Systems involving more than one energy-contributing component can be studied. Invalid and dangerous predictive models can be detected by a failure of agreement between prediction and experiment at a specific size, shape, and density. Rates of thermal decomposition for Composition B appear to be modeled adequately for critical-temperature predictions with the following kinetics constants: E = 180.2 kJ mole -1 and Z = 4.62 X 10 16 s -1

Steam explosion triggering and efficiency studies

International Nuclear Information System (INIS)

Buxton, L.D.; Nelson, L.S.; Benedick, W.B.

1979-01-01

A program at Sandia Laboratories to provide relevant data on the interaction of molten LWR core materials with water is described. Two different subtasks were established. The first was the performance of laboratory-scale experiments to investigate the ability to trigger steam explosions for realistic LWR core melt simulants under a wide range of initial conditions. The second was the performance of field-scale experiments to investigate the efficiency of converting the thermal energy of the melt into mechanical work in much larger steam explosions

Application of factor analysis to the explosive detection

International Nuclear Information System (INIS)

Park, Yong Joon; Song, Byung Chul; Im, Hee Jung; Kim, Won Ho; Cho, Jung Hwan

2005-01-01

The detection of explosive devices hidden in airline baggage is significant problem, particularly in view of the development of modern plastic explosives which can formed into various innocent-appearing shapes and which are sufficiently powerful that small quantities can destroy an aircraft in flight. Besides, the biggest difficulty occurs from long detection time required for the explosive detection system based on thermal neutron interrogation, which involves exposing baggage to slow neutrons having energy in the order of 0.025 eV. The elemental compositions of explosives can be determined by the Neutron Induced Prompt gamma Spectroscopy (NIPS) which has been installed in Korea Atomic Energy Research Institute as a tool for the detection of explosives in passenger baggage. In this work, the factor analysis has been applied to the NIPS system to increase the signal-to-noise ratio of the prompt gamma spectrum for the detection of explosive hidden in a passenger's baggage, especially for the noisy prompt gamma spectrum obtained with short measurement time

The role of fragmentation mechanism in large-scale vapor explosions

International Nuclear Information System (INIS)

Liu, Jie

2003-01-01

A non-equilibrium, multi-phase, multi-component code PROVER-I is developed for propagation phase of vapor explosion. Two fragmentation models are used. The hydrodynamic fragmentation model is the same as Fletcher's one. A new thermal fragmentation model is proposed with three kinds of time scale for modeling instant fragmentation, spontaneous nucleation fragmentation and normal boiling fragmentation. The role of fragmentation mechanisms is investigated by the simulations of the pressure wave propagation and energy conversion ratio of ex-vessel vapor explosion. The spontaneous nucleation fragmentation results in a much higher pressure peak and a larger energy conversion ratio than hydrodynamic fragmentation. The instant fragmentation gives a slightly larger energy conversion ratio than spontaneous nucleation fragmentation, and the normal boiling fragmentation results in a smaller energy conversion ratio. The detailed analysis of the structure of pressure wave makes it clear that thermal detonation exists only under the thermal fragmentation circumstance. The high energy conversion ratio is obtained in a small vapor volume fraction. However, in larger vapor volume fraction conditions, the vapor explosion is weak. In a large-scale vapor explosion, the hydrodynamic fragmentation is essential when the pressure wave becomes strong, so a small energy conversion ratio is expected. (author)

Explosion of a road tanker containing liquefied natural gas

Energy Technology Data Exchange (ETDEWEB)

Planas-Cuchi, E.; Casal, J. [Universitat Politecnica de Catalunya, Catalonia (Spain). CERTEC; Gasulla, N.; Ventosa, A. [Autonomous Government of Catalonia (Spain). General Directorate for Emergencies and Civl Security

2004-07-01

The explosion of a road tanker transporting LNG (one person killed, two injured) is studied. The analysis shows that the explosion, which followed a two-step mode as for the failure of the vessel, could have been a boiling liquid expanding vapor explosion (BLEVE). The overpressure and thermal radiation have been estimated and related to the effects observed. Only a relatively small part of the energy released in the explosion was manifested in the pressure wave. The large fragments (the three pieces into which the tank was broken) and the truck motor were ejected at various distances along the tank's main axis. (author)

A review of conventional explosives detection using active neutron interrogation

International Nuclear Information System (INIS)

Whetstone, Z.D.; Kearfott, K.J.

2014-01-01

Conventional explosives are relatively easy to obtain and may cause massive harm to people and property. There are several tools employed by law enforcement to detect explosives, but these can be subverted. Active neutron interrogation is a viable alternative to those techniques, and includes: fast neutron analysis, thermal neutron analysis, pulsed fast/thermal neutron analysis, neutron elastic scatter, and fast neutron radiography. These methods vary based on neutron energy and radiation detected. A thorough review of the principles behind, advantages, and disadvantages of the different types of active neutron interrogation is presented. (author)

Direct Observation of the Phenomenology of a Solid Thermal Explosion Using Time-Resolved Proton Radiography

International Nuclear Information System (INIS)

Smilowitz, L.; Henson, B. F.; Romero, J. J.; Asay, B. W.; Schwartz, C. L.; Saunders, A.; Merrill, F. E.; Morris, C. L.; Kwiatkowski, K.; Hogan, G.; Nedrow, P.; Murray, M. M.; Thompson, T. N.; McNeil, W.; Rightley, P.; Marr-Lyon, M.

2008-01-01

We present a new phenomenology for burn propagation inside a thermal explosion based on dynamic radiography. Radiographic images were obtained of an aluminum cased solid cylindrical sample of a plastic bonded formulation of octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine. The phenomenology observed is ignition followed by cracking in the solid accompanied by the propagation of a radially symmetric front of increasing proton transmission. This is followed by a further increase in transmission through the sample, ending after approximately 100 μs. We show that these processes are consistent with the propagation of a convective burn front followed by consumption of the remaining solid by conductive particle burning

Thermal interaction of molten copper with water

International Nuclear Information System (INIS)

Zyszkowski, W.

1975-01-01

Experimental work was performed to study the thermal interaction between molten copper particles (in the range of temperature from the copper melting point to about 1800 0 C) and water from about 15-80 0 C. The transient temperatures of the copper particles and water before and during their thermal interaction were measured. The history of the phenomena was filmed by means of a high speed FASTAX camera (to 8000 f/s). Classification of the observed phenomena and description of the heat-transfer modes were derived. One among the phenomena was the thermal explosion. The necessary conditions for the thermal explosion are discussed and their physical interpretation is given. According to the hypothesis proposed, the thermal explosion occurs when the molten metal has the temperature of its solidification and the heat transfer on its surface is sufficiently intensive. The 'sharp-change' of the crystalline structure during the solidification of the molten metal is the cause of the explosion fragmentation. (author)

The surface quasiliquid melt acceleration and the role of thermodynamic phase in the thermal decomposition of crystalline organic explosives

Energy Technology Data Exchange (ETDEWEB)

Henson, Bryan F [Los Alamos National Laboratory

2010-01-01

We show that melt acceleration in the thermal decomposition of crystalline organic solids is a manifestation of the surface quasiliquid phase. We derive a single universal rate law for melt acceleration that is a simple function of the metastable liquid activity below the melting point, and has a zero order term proportional to the quasiliquid thickness. We argue that the underlying mechanisms of this model will provide a molecular definition for the stability of the class of secondary explosives.

Gas pressure from a nuclear explosion in oil shale

International Nuclear Information System (INIS)

Taylor, R.W.

1975-01-01

The quantity of gas and the gas pressure resulting from a nuclear explosion in oil shale is estimated. These estimates are based on the thermal history of the rock during and after the explosion and the amount of gas that oil shale releases when heated. It is estimated that for oil shale containing less than a few percent of kerogen the gas pressure will be lower than the hydrostatic pressure. A field program to determine the effects of nuclear explosions in rocks that simulate the unique features of oil shale is recommended. (U.S.)

Observations of Tin/Water Thermal Explosions in a Long-Tube Geometry. Their Interpretation and Consequences for the Detonation Model

International Nuclear Information System (INIS)

Hall, R.W.; Board, S.J.; Baines, M.

1979-01-01

This paper presents details of experiments designed to test the detonation model of thermal explosions (Board et al, 1975); on this theory large-scale explosions should propagate steadily at supersonic velocities through a fuel coolant mixture, giving a yield which has been shown to depend on details of the fragmentation and heat transfer behind the shock front. Observations of propagating explosions have been reported previously. In the present work, a long-tube geometry is used since in 1D, propagation measurements are particularly easy to interpret. Also, in 2D and 3D geometries radial flow can tend to extinguish shock waves and if a single-phase region of coolant is present, pressure pulses can propagate ahead of the two-phase shock in the intermixed region. This paper describes the six experiments that all use molten tin and water mixtures. In the first four, detailed pressure measurement was the main objective; the last two are attempts at flow visualization to aid the interpretation of these. The results obtained and the implications for the detonation model are discussed. A detailed interpretation in terms of fragmentation and heat transfer processes behind the shock is attempted. The implications of the work for reactor materials are then briefly outlined

Biological consequences of atomic explosions

International Nuclear Information System (INIS)

Messerschmidt, O.

1984-01-01

After an introductory chapter of the development and properties of nuclear weapons and the events of Hiroshima and Nagasaki, this books shows the effects of atomic explosions for man: effects of the pressure wave, thermal radiation, initial nuclear radiation alone or in conjunction and possible medical help. In addition the less massive damage caused by induced radioactivity and fallout, their prevention resp. treatment and the malignant/nonmalignant late effects are discussed. A further chapter deals with the psychological and epidemiological effects of atomic explosions, the consequences for food and water supply, and the construction of shetters. The last chapter is concerned with the problem of organising medical help. (MG) [de

A DSC analysis of inverse salt-pair explosive composition

Energy Technology Data Exchange (ETDEWEB)

Babu, E. Suresh; Kaur, Sukhminder [Central Forensic Science Laboratory, Explosives Division, Ramanthapur, Hyderabad 500013 (India)

2004-02-01

Alkali nitrates are used as an ingredient in low explosive compositions and pyrotechnics. It has been suggested that alkali nitrates can form inverse salt-pair explosives with the addition of ammonium chloride. Therefore, the thermal behavior of low explosive compositions containing potassium nitrate mixed with ammonium chloride has been studied using Differential Scanning Calorimetry (DSC). Results provide information about the ion exchange reaction between these two chemical substances and the temperature region at which the formation of a cloud of salt particles of potassium chloride takes place. Furthermore, the addition of ammonium chloride quenches the flame of deflagrating compositions and causes the mixture to undergo explosive decomposition at relatively low temperatures. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

Fire suppression as a thermal implosion

Science.gov (United States)

Novozhilov, Vasily

2017-01-01

The present paper discusses the possibility of the thermal implosion scenario. This process would be a reverse of the well known thermal explosion (autoignition) phenomenon. The mechanism for thermal implosion scenario is proposed which involves quick suppression of the turbulent diffusion flame. Classical concept of the thermal explosion is discussed first. Then a possible scenario for the reverse process (thermal implosion) is discussed and illustrated by a relevant mathematical model. Based on the arguments presented in the paper, thermal implosion may be observed as an unstable equilibrium point on the generalized Semenov diagram for turbulent flame, however this hypothesis requires ultimate experimental confirmation.

Nucleation Characteristics in Physical Experiments/explosions

International Nuclear Information System (INIS)

Henry, R.E.; Fauske, Hans K.

1976-01-01

Large-scale vapor explosion experiments have shown that intimate contact between hot and cold liquids, and a temperature upon contact that is greater than the spontaneous nucleation temperature of the system, are two necessary conditions for the onset of large scale vapor explosions. A model, based on spontaneous nucleation of the homogeneous type, has been proposed to describe the relevant processes and the resulting energetics for explosive boiling systems. The model considers that spontaneous nucleation cannot occur either during the relief time for constant volume heating or until the thermal boundary layer is sufficiently thick to support a vapor cavity of the critical size. After nucleation, bubble growth does not occur until an acoustic wave establishes a pressure gradient in the cold liquid. These considerations lead to the prediction that, for a given temperature, drops greater than a critical size will remain in film boiling due to coalescence of vapor nuclei and drops smaller than this value will wet and be captured by the hot liquid surface. These results are compared to small drop data for well-wetted systems and excellent agreement is obtained between the observed behavior and the model predictions. In conclusion: A model, based on spontaneous nucleation, has been proposed to describe vaporization potential and behavior upon contact in a liquid/liquid system. This behavior is determined by the size of the liquid mass, single-phase pressurization and acoustic relief, nucleation frequency due to random density fluctuations, the initiation of unstable growth and acoustic relief, and the development of the thermal boundary layer in the cold liquid. The proposed model predicts that the stability of a given size drop upon intimate contact with another liquid is extremely dependent upon the interface temperature. For low interface temperatures, large masses will be captured by the hot liquid and the resulting vaporization rates will be extremely low because

Progress in the development of explosives materials detectors

International Nuclear Information System (INIS)

Williams, W.D.; Conrad, F.J.; Sandlin, L.L.; Burrows, T.A.

1978-01-01

Five hand-held explosives vapor detectors (Elscint Model EXD-2, ITI Model 70, Leigh-Marsland Model S-201, Pye Dynamics Model PD.2.A, and Xonics Model GC-710) were evaluated for sensitivity to a variety of explosives, identification of false alarm agents, and general performance and maintenance characteristics. The results of this evaluation, as presented, indicate that there is no single explosives detector which is best-suited for use at all nuclear facilities. Rather, there are several site-specific elements which must be considered when choosing an explosives detector. There are several new explosives detector technologies being developed which will out-perform existing commercial equipment. Some of these new detectors may be commercially available by the end of fiscal year 1980 and will be cost-effective to purchase and operate. The following areas of explosives detection research are discussed: nitrogen-phosphorous detectors, plasma chromatography, mass spectroscopy, small animal olfactory, vapor preconcentration, nuclear quadrupole resonance, far infrared radiation imaging, nuclear magnetic resonance, thermal neutron activation, and computerized tomography

MEMS-based Porous Silicon Preconcentrators Filled with Carbopack-B for Explosives Detection

OpenAIRE

Camara , El Hadji Malik; James , Franck; Breuil , Philippe; Pijolat , Christophe; Briand , Danick; De Rooij , Nicolaas F

2014-01-01

International audience; In this paper we report the detection of explosive compounds using a miniaturized gas preconcentrator (μGP) made of porous silicon (PS) filled in with Carbopack B as an adsorbent material. The μGP includes also a platinum heater patterned at the backside and fluidic connectors sealed on the glass cover. Our μGP is designed and optimized through fluidic and thermal simulations for meeting the requirements of trace explosives detection. The thermal mass of the device was...

Results of measurements of thermal interaction between molten metal and water

International Nuclear Information System (INIS)

Zyszkowski, W.

1975-10-01

The report describes results of an experimental investigation into thermal interaction of molten metals with water. The experiments were performed in two stages: the aim of the first stage was to study the general character of thermal interaction between molten metal and water and to measure the Leidenfrost temperature of the inverse Leidenfrost phenomenon. The second stage was directed to the experimental study of the triggering mechanism of thermal explosion. The experimental material gathered in this study includes: 1) transient temperature measurements in the hot material and in water, 2) measurements of pressure and reactive force combined with thermal explosion, 3) high-speed films of thermal interaction, 4) investigation results of thermal explosion debris (microscopic, mechanical, metallographical and chemical). The most significant observation is, that small jets from the main particle mass occuring 1 to 10 msec before, precede thermal explosion. (orig.) [de

High-nitrogen explosives

Energy Technology Data Exchange (ETDEWEB)

Naud, D. (Darren); Hiskey, M. A. (Michael A.); Kramer, J. F. (John F.); Bishop, R. L. (Robert L.); Harry, H. H. (Herbert H.); Son, S. F. (Steven F.); Sullivan, G. K. (Gregg K.)

2002-01-01

The syntheses and characterization of various tetrazine and furazan compounds offer a different approach to explosives development. Traditional explosives - such as TNT or RDX - rely on the oxidation of the carbon and hydrogen atoms by the oxygen carrying nitro group to produce the explosive energy. High-nitrogen compounds rely instead on large positive heats of formation for that energy. Some of these high-nitrogen compounds have been shown to be less sensitive to initiation (e.g. by impact) when compared to traditional nitro-containing explosives of similar performances. Using the precursor, 3,6-bis-(3,5-dimethylpyrazol-1-yl)-s-tetrazine (BDT), several useful energetic compounds based on the s-tetrazine system have been synthesized and studied. The compound, 3,3{prime}-azobis(6-amino-s-tetrazine) or DAAT, detonates as a half inch rate stick despite having no oxygen in the molecule. Using perfluoroacetic acid, DAAT can be oxidized to give mixtures of N-oxide isomers (DAAT03.5) with an average oxygen content of about 3.5. This energetic mixture burns at extremely high rates and with low dependency on pressure. Another tetrazine compound of interest is 3,6-diguanidino-s-tetrazine(DGT) and its dinitrate and diperchlorate salts. DGT is easily synthesized by reacting BDT with guanidine in methanol. Using Caro's acid, DGT can be further oxidized to give 3,6-diguanidino-s-tetrazine-1,4-di-N-oxide (DGT-DO). Like DGT, the di-N-oxide can react with nitric acid or perchloric acid to give the dinitrate and the diperchlorate salts. The compounds, 4,4{prime}-diamino-3,3{prime}-azoxyfurazan (DAAF) and 4,4{prime}-diamino-3,3{prime}-azofurazan (DAAzF), may have important future roles in insensitive explosive applications. Neither DAAF nor DAAzF can be initiated by laboratory impact drop tests, yet both have in some aspects better explosive performances than 1,3,5-triamino-2,4,6-trinitrobenzene TATB - the standard of insensitive high explosives. The thermal stability of DAAz

Vapor generation methods for explosives detection research

Energy Technology Data Exchange (ETDEWEB)

Grate, Jay W.; Ewing, Robert G.; Atkinson, David A.

2012-12-01

The generation of calibrated vapor samples of explosives compounds remains a challenge due to the low vapor pressures of the explosives, adsorption of explosives on container and tubing walls, and the requirement to manage (typically) multiple temperature zones as the vapor is generated, diluted, and delivered. Methods that have been described to generate vapors can be classified as continuous or pulsed flow vapor generators. Vapor sources for continuous flow generators are typically explosives compounds supported on a solid support, or compounds contained in a permeation or diffusion device. Sources are held at elevated isothermal temperatures. Similar sources can be used for pulsed vapor generators; however, pulsed systems may also use injection of solutions onto heated surfaces with generation of both solvent and explosives vapors, transient peaks from a gas chromatograph, or vapors generated by s programmed thermal desorption. This article reviews vapor generator approaches with emphasis on the method of generating the vapors and on practical aspects of vapor dilution and handling. In addition, a gas chromatographic system with two ovens that is configurable with up to four heating ropes is proposed that could serve as a single integrated platform for explosives vapor generation and device testing. Issues related to standards, calibration, and safety are also discussed.

Detection of plastic explosives using thermal neutron radiography

International Nuclear Information System (INIS)

Hacidume, Leo Ryoske

1999-12-01

The work aims to demonstrate the potentiality of the neutron radiography technique, allied to the computerized tomography by transmission, to both detect and visualize plastic explosive samples in several hidden conditions, using a simple scanner as a digitalisation instrument. Each tomographic essay was obtained in the J-9 channel of the Argonauta Research Reactor of IEN/CNEN, in groups of six neutron radiographic projections, performed with an angular increment of 30 deg C, in a period of time of 30 minutes for each projection. Two groups of tomographic reconstructions were generated, distinguished by the digitalisation process of the interested lines in the reconstruction plane coming from the projection groups, utilization a scanner and a microdensitometer, respectively. The reconstruction of the bi-dimensional image of the transverse section, in relation to this plane, was processed making use of the Image Reconstruction Algorithmic of an Image based on the Maximum Entropy principle (ARIEM). From the qualitative analysis of the images, we conclude that the neutron radiographic system was able to detect the explosive sample in a satisfactory way while the quantitative analysis confirmed the application effectiveness of a scanner to acquire the projection dates whose objective is only a reconnaissance. (author)

Explosive bonding and its application in the Advanced Photon Source front-end and beamline components design

International Nuclear Information System (INIS)

Shu, D.; Li, Y.; Ryding, D.; Kuzay, T.M.

1994-01-01

Explosive bonding is a bonding method in which the controlled energy of a detonating explosive is used to create a metallurgical bonding between two or more similar or dissimilar materials. Since 1991, a number of explosive-bonding joints have been designed for high-thermal-load ultrahigh-vacuum (UHV) compatible components in the Advanced Photon Source. A series of standardized explosive bonded joint units has also been designed and tested, such as: oxygen-free copper (OFHC) to stainless-steel vacuum joints for slits and shutters, GlidCop to stainless-steel vacuum joints for fixed masks, and GlidCop to OFHC thermal and mechanical joints for shutter face-plates, etc. The design and test results for the explosive bonding units to be used in the Advanced Photon Source front ends and beamlines will be discussed in this paper

Steam explosion triggering and efficiency studies

International Nuclear Information System (INIS)

Buxton, L.D.; Nelson, L.S.; Benedick, W.B.

1979-01-01

Laboratory experiments on the thermal interaction of simulated light water reactor (LWR) fuel melts and water are summarized. Their purpose was to investigate the possibility of steam explosions occurring for a range of hypothetical accident conditions. Pressure, temperature, hot liquid motion and cold liquid motion were monitored during the experiments

Six-year longitudinal study of pathways leading to explosive anger involving the traumas of recurrent conflict and the cumulative sense of injustice in Timor-Leste.

Science.gov (United States)

Silove, Derrick; Mohsin, Mohammed; Tay, Alvin Kuowei; Steel, Zachary; Tam, Natalino; Savio, Elisa; Da Costa, Zelia Maria; Rees, Susan

2017-10-01

violence and addressing persisting feelings of injustice may assist in reducing anger in conflict-affected societies. Whether explosive anger at the individual level increases risk of collective violence under conditions of social and political instability requires further inquiry.

Explosive simulants for testing explosive detection systems

Science.gov (United States)

Kury, John W.; Anderson, Brian L.

1999-09-28

Explosives simulants that include non-explosive components are disclosed that facilitate testing of equipment designed to remotely detect explosives. The simulants are non-explosive, non-hazardous materials that can be safely handled without any significant precautions. The simulants imitate real explosives in terms of mass density, effective atomic number, x-ray transmission properties, and physical form, including moldable plastics and emulsions/gels.

Vapor Explosions with Subcooled Freon

International Nuclear Information System (INIS)

Henry, R.E.; Fauske, Hans K.; McUmber, L.M.

1976-01-01

Explosive vapor formation accompanied by destructive shock waves, can be produced when two liquids, at much different temperatures, are brought into intimate contact. A proposed analytical model states that the interface temperature upon contact between the two liquid systems, gust be greater than or equal to the spontaneous nucleation temperature of that liquid-liquid system and that the thermal boundary layer must be sufficiently developed to support a critical size cavity. For time scales greater than 10-12 sec, the interface temperature upon contact of two semi-infinite masses, with constant thermal properties, can be related to the initial liquid temperatures. The spontaneous nucleation behavior at the interface can either be heterogeneous or homogeneous in nature. In either case, the critical size cavities, which initiate the vaporization process, are produced by local density fluctuations within the cold liquid. For homogeneous conditions, the two liquids present a well-wetted system and the vapor embryos are produced entirely within the cold liquid. For heterogeneous conditions, which result from poor, or imperfect wetting, at the liquid-liquid interface, the critical sized cavities are created at the interface at somewhat lower temperatures. A sequence of experiments, using Freon-22 and water, Freon-22 and mineral oil, and Freon-12 and mineral oil have been performed to test this spontaneous nucleation premise. For Freon-22 at its normal boiling point, the interface temperature of the water must be at least 77 deg. C before the interface temperature equals or exceeds the minimum homogeneous nucleation value of 54 deg. C and 84 deg. C before the interface temperature equals 60 deg. C where the homogeneous nucleation rate becomes truly explosive. The Freon-water test demonstrated explosive interactions for water temperatures considerably lower than this value and this was attributed to the heterogeneous nucleation characteristics of that particular system

A model of vulcanian explosions

International Nuclear Information System (INIS)

Woods, A.W.

1995-01-01

We present a model of the initial stages of the explosive eruption of magma from a volcanic conduit as occurs in Vulcanian style eruptions. We assume there is a volatile rich (1-10 wt%) mixture of magma, vaporised groundwater and exsolved volatiles, trapped at high pressure (1-100 atm) just below a plug in a volcanic conduit. If the plug disrupts, there is an explosive eruption in which a rarefaction wave propagates into the conduit allowing the volatile rich mixture to expand and discharge into the atmosphere ahead of the vent. Typically, the explosions are so rapid that coarse grained ejecta (>0.5 mm) do not remain in thermal equilibrium with the gas, and this leads to significantly lower velocities and temperatures than predicted by an equilibrium model. Material may erupt from the vent at speeds of 100-400 m s -1 with an initial mass flux of order 10 7 -10 9 kg s -1 , consistent with video observations of eruptions and measurements of the ballistic dispersal of large clasts. (orig.)

"The war against women". Media representations of men's violence against women in Australia.

Science.gov (United States)

Howe, A

1997-02-01

This article analyzes how a newspaper in Victoria, Australia, represented violence against women in a special series entitled, "The War Against Women." True to the series title, the series appropriated all of the metaphors of war and dealt with violence against women in much the same fashion as it would report a war, speculating as to its causes, mapping its prevalence, reporting deaths, and referring to "explosions" of violence. As in war coverage, the series included findings of a poll of public opinion, told a story of contrition from an enemy who surrendered (a man in counseling), and offered editorials. While it drew attention to one of society's most pressing and intractable social problems, the paper ignored its own previous reports on domestic violence to gain the shock value of the "new" and, therefore, perpetuated a pattern of "discovery, forgetting, and rediscovery" of violence against women. The paper also failed to apply the feminist notion of a continuum of male violence or to breach the chasm between feminist and public understanding of male violence. Finally, the paper used editorial disclaimers to minimalize men's responsibility and distance itself from feminists. Thus, it placed its critique of men's pervasive violence against women within the hegemonic narratives of gender relations, which hold that women acquiesce in domestic violence, feminists vilify men, and men are a much-maligned group not responsible for the bad behavior of a minority. The paper, thus, conveys that idea that this war will not be won.

Monte Carlo simulation of explosive detection system based on a Deuterium-Deuterium (D-D) neutron generator.

Science.gov (United States)

Bergaoui, K; Reguigui, N; Gary, C K; Brown, C; Cremer, J T; Vainionpaa, J H; Piestrup, M A

2014-12-01

An explosive detection system based on a Deuterium-Deuterium (D-D) neutron generator has been simulated using the Monte Carlo N-Particle Transport Code (MCNP5). Nuclear-based explosive detection methods can detect explosives by identifying their elemental components, especially nitrogen. Thermal neutron capture reactions have been used for detecting prompt gamma emission (10.82MeV) following radiative neutron capture by (14)N nuclei. The explosive detection system was built based on a fully high-voltage-shielded, axial D-D neutron generator with a radio frequency (RF) driven ion source and nominal yield of about 10(10) fast neutrons per second (E=2.5MeV). Polyethylene and paraffin were used as moderators with borated polyethylene and lead as neutron and gamma ray shielding, respectively. The shape and the thickness of the moderators and shields are optimized to produce the highest thermal neutron flux at the position of the explosive and the minimum total dose at the outer surfaces of the explosive detection system walls. In addition, simulation of the response functions of NaI, BGO, and LaBr3-based γ-ray detectors to different explosives is described. Copyright © 2014 Elsevier Ltd. All rights reserved.

Hydrothermal processes above the Yellowstone magma chamber: Large hydrothermal systems and large hydrothermal explosions

Science.gov (United States)

Morgan, L.A.; Shanks, W.C. Pat; Pierce, K.L.

2009-01-01

Hydrothermal explosions are violent and dramatic events resulting in the rapid ejection of boiling water, steam, mud, and rock fragments from source craters that range from a few meters up to more than 2 km in diameter; associated breccia can be emplaced as much as 3 to 4 km from the largest craters. Hydrothermal explosions occur where shallow interconnected reservoirs of steam- and liquid-saturated fluids with temperatures at or near the boiling curve underlie thermal fields. Sudden reduction in confi ning pressure causes fluids to fl ash to steam, resulting in signifi cant expansion, rock fragmentation, and debris ejection. In Yellowstone, hydrothermal explosions are a potentially signifi cant hazard for visitors and facilities and can damage or even destroy thermal features. The breccia deposits and associated craters formed from hydrothermal explosions are mapped as mostly Holocene (the Mary Bay deposit is older) units throughout Yellowstone National Park (YNP) and are spatially related to within the 0.64-Ma Yellowstone caldera and along the active Norris-Mammoth tectonic corridor. In Yellowstone, at least 20 large (>100 m in diameter) hydrothermal explosion craters have been identifi ed; the scale of the individual associated events dwarfs similar features in geothermal areas elsewhere in the world. Large hydrothermal explosions in Yellowstone have occurred over the past 16 ka averaging ??1 every 700 yr; similar events are likely in the future. Our studies of large hydrothermal explosion events indicate: (1) none are directly associated with eruptive volcanic or shallow intrusive events; (2) several historical explosions have been triggered by seismic events; (3) lithic clasts and comingled matrix material that form hydrothermal explosion deposits are extensively altered, indicating that explosions occur in areas subjected to intense hydrothermal processes; (4) many lithic clasts contained in explosion breccia deposits preserve evidence of repeated fracturing

Research topics in explosives - a look at explosives behaviors

International Nuclear Information System (INIS)

Maienschein, J L

2014-01-01

The behaviors of explosives under many conditions - e.g., sensitivity to inadvertent reactions, explosion, detonation - are controlled by the chemical and physical properties of the explosive materials. Several properties are considered for a range of improvised and conventional explosives. Here I compare these properties across a wide range of explosives to develop an understanding of explosive behaviors. For improvised explosives, which are generally heterogeneous mixtures of ingredients, a range of studies is identified as needed to more fully understand their behavior and properties. For conventional explosives, which are generally comprised of crystalline explosive molecules held together with a binder, I identify key material properties that determine overall sensitivity, including the extremely safe behavior of Insensitive High Explosives, and discuss an approach to predicting the sensitivity or insensitivity of an explosive.

Soudage par explosion thermique sous charge de cermets poreux à base de TiC-Ni sur substrat en acier-comportement tribologique Welding of porous TiC–Ni based cermets on substrate steel by thermal explosion under load-tribological behaviour

Directory of Open Access Journals (Sweden)

Lemboub Samia

2013-11-01

Full Text Available Dans ce travail, nous nous intéressons à l'élaboration de cermets à base de TiC-Ni par dispersion de particules de carbures, oxydes ou borures dans une matrice de nickel, grâce à la technique de l'explosion thermique sous une charge de 20 MPa. La combustion de mélanges actifs (Ti-C-Ni-An où An = Al2O3, MgO, SiC, TiB2, WC, basée sur la réaction de synthèse de TiC (ΔHf298K = −184 kJ/mole, génère des cermets complexes. Un court maintien sous charge du cermet à 1373 K, après l'explosion thermique, permet son soudage sur un substrat en acier XC55. Les cermets obtenus dans ces conditions demeurent poreux et conservent une porosité de l'ordre de 25–35 %. La densité relative du cermet, sa dureté et son comportement tribologique, dépendront de la nature de l'addition dans les mélanges de départ. Porous TiC-Ni based cermets were obtained by dispersion of carbides, oxides or borides particles in a nickel matrix thanks to the thermal explosion technique realized under a load of 20 MPa. The combustion of active mixtures (Ti-C-Ni-An where An = Al2O3, MgO, SiC, TiB2 or WC based on the titanium carbide reaction synthesis (ΔHf = −184 kJ/mol, generates porous complex cermets. After the thermal explosion, a short maintenance under load at 1373 K of the combustion product, allows at the same time the cermets welding on a carbon steel substrate. The obtained cermets under these conditions preserve a porosity of about 25–35%. The relative density, hardness and tribological behaviour of the complex cermets depend on the additions nature (An in the starting mixtures.

Thermal interaction for molten tin dropped into water

Energy Technology Data Exchange (ETDEWEB)

Arakeri, V.H.; Catton, I.; Kastenberg, W.E.; Plesset, M.S.

1978-03-01

Multiflash photography with extremely short duration exposure times per flash was used to observe the interaction of molten tin dropped into a water bath. Detailed photographic evidence is presented which demonstrates that transition, or nucleate boiling, is a possible triggering mechanism for vapor explosions. It was also found that the thermal constraints required to produce vapor explosions could be relaxed by introducing a stable thermal stratification within the coolant. In the present work, the threshold value of the initial tin temperature required for vapor explosion was reduced from about 500 to 343/sup 0/C.

Features of the incorporation of single and double based powders within emulsion explosives

Science.gov (United States)

Ribeiro, J. B.; Mendes, R.; Tavares, B.; Louro, C.

2014-05-01

In this work, features of the thermal and detonation behaviour of compositions resulting from the mixture of single and double based powders within ammonium nitrate based emulsion explosives are shown. Those features are portrayed through results of thermodynamic-equilibrium calculations of the detonation velocity, the chemical compatibility assessment through differential thermal analysis [DTA] and thermo gravimetric analysis [TGA], the experimental determination of the detonation velocity and a comparative evaluation of the shock sensitivity using a modified version of the "gap-test". DTA/TGA results for the compositions and for the individual components overlap until the beginning of the thermal decomposition which is an indication of the absence of formation of any new chemical species and so of the compatibility of the components of the compositions. After the beginning of the thermal decomposition it can be seen that the rate of mass loss is much higher for the compositions with powder than for the one with sole emulsion explosive. Both, theoretical and experimental, values of the detonation velocity have been shown to be higher for the powdered compositions than for the sole emulsion explosive. Shock sensitivity assessments have ended-up with a slightly bigger sensitivity for the compositions with double based powder when compared to the single based compositions or to the sole emulsion.

Features of the incorporation of single and double based powders within emulsion explosives

International Nuclear Information System (INIS)

Ribeiro, J B; Mendes, R; Tavares, B; Louro, C

2014-01-01

In this work, features of the thermal and detonation behaviour of compositions resulting from the mixture of single and double based powders within ammonium nitrate based emulsion explosives are shown. Those features are portrayed through results of thermodynamic-equilibrium calculations of the detonation velocity, the chemical compatibility assessment through differential thermal analysis [DTA] and thermo gravimetric analysis [TGA], the experimental determination of the detonation velocity and a comparative evaluation of the shock sensitivity using a modified version of the g ap-test . DTA/TGA results for the compositions and for the individual components overlap until the beginning of the thermal decomposition which is an indication of the absence of formation of any new chemical species and so of the compatibility of the components of the compositions. After the beginning of the thermal decomposition it can be seen that the rate of mass loss is much higher for the compositions with powder than for the one with sole emulsion explosive. Both, theoretical and experimental, values of the detonation velocity have been shown to be higher for the powdered compositions than for the sole emulsion explosive. Shock sensitivity assessments have ended-up with a slightly bigger sensitivity for the compositions with double based powder when compared to the single based compositions or to the sole emulsion.

Modelling of vapour explosion in stratified geometrie

International Nuclear Information System (INIS)

Picchi, St.

1999-01-01

When a hot liquid comes into contact with a colder volatile liquid, one can obtain in some conditions an explosive vaporization, told vapour explosion, whose consequences can be important on neighbouring structures. This explosion needs the intimate mixing and the fine fragmentation between the two liquids. In a stratified vapour explosion, these two liquids are initially superposed and separated by a vapor film. A triggering of the explosion can induce a propagation of this along the film. A study of experimental results and existent models has allowed to retain the following main points: - the explosion propagation is due to a pressure wave propagating through the medium; - the mixing is due to the development of Kelvin-Helmholtz instabilities induced by the shear velocity between the two liquids behind the pressure wave. The presence of the vapour in the volatile liquid explains experimental propagation velocity and the velocity difference between the two fluids at the pressure wave crossing. A first model has been proposed by Brayer in 1994 in order to describe the fragmentation and the mixing of the two fluids. Results of the author do not show explosion propagation. We have therefore built a new mixing-fragmentation model based on the atomization phenomenon that develops itself during the pressure wave crossing. We have also taken into account the transient aspect of the heat transfer between fuel drops and the volatile liquid, and elaborated a model of transient heat transfer. These two models have been introduced in a multi-components, thermal, hydraulic code, MC3D. Results of calculation show a qualitative and quantitative agreement with experimental results and confirm basic options of the model. (author)

The cross-national epidemiology of DSM-IV intermittent explosive disorder.

Science.gov (United States)

Scott, K M; Lim, C C W; Hwang, I; Adamowski, T; Al-Hamzawi, A; Bromet, E; Bunting, B; Ferrand, M P; Florescu, S; Gureje, O; Hinkov, H; Hu, C; Karam, E; Lee, S; Posada-Villa, J; Stein, D; Tachimori, H; Viana, M C; Xavier, M; Kessler, R C

2016-11-01

This is the first cross-national study of intermittent explosive disorder (IED). A total of 17 face-to-face cross-sectional household surveys of adults were conducted in 16 countries (n = 88 063) as part of the World Mental Health Surveys initiative. The World Health Organization Composite International Diagnostic Interview (CIDI 3.0) assessed DSM-IV IED, using a conservative definition. Lifetime prevalence of IED ranged across countries from 0.1 to 2.7% with a weighted average of 0.8%; 0.4 and 0.3% met criteria for 12-month and 30-day prevalence, respectively. Sociodemographic correlates of lifetime risk of IED were being male, young, unemployed, divorced or separated, and having less education. The median age of onset of IED was 17 years with an interquartile range across countries of 13-23 years. The vast majority (81.7%) of those with lifetime IED met criteria for at least one other lifetime disorder; co-morbidity was highest with alcohol abuse and depression. Of those with 12-month IED, 39% reported severe impairment in at least one domain, most commonly social or relationship functioning. Prior traumatic experiences involving physical (non-combat) or sexual violence were associated with increased risk of IED onset. Conservatively defined, IED is a low prevalence disorder but this belies the true societal costs of IED in terms of the effects of explosive anger attacks on families and relationships. IED is more common among males, the young, the socially disadvantaged and among those with prior exposure to violence, especially in childhood.

New Mix Explosives for Explosive Welding

Science.gov (United States)

Andreevskikh, Leonid

2011-06-01

Suggested and tested were some mix explosives--powder mixtures of a brisant high explosive (HE = RDX, PETN) and an inert diluent (baking soda)--for use in explosive welding. RDX and PETN were selected in view of their high throwing ability and low critical diameter. Since the decomposition of baking soda yields a huge amount of gaseous products, its presence ensures (even at a low HE percentage) a throwing speed that is sufficient for realization of explosive welding, at a reduced brisant action of charge. Mix chargers containing 30-70 wt % HE (the rest baking soda) have been tested experimentally and optimized. For study of possibility to reduce critical diameter of HE mixture, the mixture was prepared where HE crystal sizes did not exceed 10 μm. The tests, which were performed with this HE, revealed that the mixture detonated stably with the velocity D ~ 2 km/s, if the layer thickness was d = 2 mm. The above explosives afford to markedly diminish deformations within the oblique impact zone and thus to carry out explosive welding of hollow items and thin metallic foils.

Aggressiveness, violence, homicidality, homicide, and Lyme disease.

Science.gov (United States)

Bransfield, Robert C

2018-01-01

No study has previously analyzed aggressiveness, homicide, and Lyme disease (LD). Retrospective LD chart reviews analyzed aggressiveness, compared 50 homicidal with 50 non-homicidal patients, and analyzed homicides. Most aggression with LD was impulsive, sometimes provoked by intrusive symptoms, sensory stimulation or frustration and was invariably bizarre and senseless. About 9.6% of LD patients were homicidal with the average diagnosis delay of 9 years. Postinfection findings associated with homicidality that separated from the non-homicidal group within the 95% confidence interval included suicidality, sudden abrupt mood swings, explosive anger, paranoia, anhedonia, hypervigilance, exaggerated startle, disinhibition, nightmares, depersonalization, intrusive aggressive images, dissociative episodes, derealization, intrusive sexual images, marital/family problems, legal problems, substance abuse, depression, panic disorder, memory impairments, neuropathy, cranial nerve symptoms, and decreased libido. Seven LD homicides included predatory aggression, poor impulse control, and psychosis. Some patients have selective hyperacusis to mouth sounds, which I propose may be the result of brain dysfunction causing a disinhibition of a primitive fear of oral predation. LD and the immune, biochemical, neurotransmitter, and the neural circuit reactions to it can cause impairments associated with violence. Many LD patients have no aggressiveness tendencies or only mild degrees of low frustration tolerance and irritability and pose no danger; however, a lesser number experience explosive anger, a lesser number experience homicidal thoughts and impulses, and much lesser number commit homicides. Since such large numbers are affected by LD, this small percent can be highly significant. Much of the violence associated with LD can be avoided with better prevention, diagnosis, and treatment of LD.

Intimate partner violence perpetrators in a forensic psychiatric outpatient setting: criminal history, psychopathology, and victimization.

Science.gov (United States)

Henrichs, Jens; Bogaerts, Stefan; Sijtsema, Jelle; Klerx-van Mierlo, Fanny

2015-07-01

This study investigated criminological, psychopathological, and victimological profiles of intimate partner violence (IPV) perpetrators in a sample of 119 Dutch female and male forensic psychiatric outpatients aged 18 to 58 years. In addition, differences in criminological, psychopathological, and victimological factors between IPV perpetrators (n = 61, 51.3%) and non-intimate violence (NIV) perpetrators (n = 58, 48.7%) were examined. All data, including information on demographics, criminal history, history of psychological, sexual, and physical victimization during childhood or adolescence, family history of psychopathology, history of psychopathology in childhood and adolescence, and mental disorders, were derived from archival electronic medical records. Mental disorders were measured using structured psychiatric interviews and final consensus diagnoses were established during weekly case consultations. Both IPV and NIV perpetrators displayed high rates of criminal history, psychopathology, and previous victimization, but the two groups did not differ in these factors with two exceptions. IPV perpetrators were significantly more likely to have higher rates of previous physical victimization and intermittent explosive disorder than NIV perpetrators. The current study suggests that a history of physical victimization and intermittent explosive disorder are specific characteristics of IPV perpetrators in a forensic psychiatric outpatient setting. Future research should focus on mechanisms explaining the association of childhood victimization and IPV and increase our understanding of the role of intermittent explosive disorder in IPV. © The Author(s) 2014.

The effect of explosive percentage on underwater explosion energy release of hexanitrohexaazaisowurtzitane and octogen based aluminized explosives

Directory of Open Access Journals (Sweden)

Qingjie Jiao

2018-03-01

Full Text Available To control the explosion energy output by optimizing explosive components is a key requirement in a number of different application areas. The effect of different Al/O Ratio on underwater explosion of aluminized explosives has been studied detailedly. However, the effect of explosive percentage in the same Al/O Ratio is rarely researched, especially for Hexanitrohexaazaisowurtzitane (CL-20 based aluminized explosives. In this study, we performed the underwater explosion experiments with 1.2-kilogram explosives in order to investigate the explosion energy released from CL-20 and Octogen (HMX based aluminized explosives. The percentage of the explosive varied from 5% to 30% and it is shown that: the shockwave peak pressure (pm grows gradually; shock wave energy (Es continues increasing, bubble energy (Eb increases then decreases peaking at 15% for both formulas, and the total energy (E and energy release rate (η peak at 20% for CL-20 and 15% for HMX. This paper outlines the physical mechanism of Eb change under the influence of an aluminium initial reaction temperature and reaction active detonation product percentage coupling. The result shows that CL-20 is superior as a new high explosive and has promising application prospects in the regulation of explosive energy output for underwater explosives.

The effect of explosive percentage on underwater explosion energy release of hexanitrohexaazaisowurtzitane and octogen based aluminized explosives

Science.gov (United States)

Jiao, Qingjie; Wang, Qiushi; Nie, Jianxin; Guo, Xueyong; Zhang, Wei; Fan, Wenqi

2018-03-01

To control the explosion energy output by optimizing explosive components is a key requirement in a number of different application areas. The effect of different Al/O Ratio on underwater explosion of aluminized explosives has been studied detailedly. However, the effect of explosive percentage in the same Al/O Ratio is rarely researched, especially for Hexanitrohexaazaisowurtzitane (CL-20) based aluminized explosives. In this study, we performed the underwater explosion experiments with 1.2-kilogram explosives in order to investigate the explosion energy released from CL-20 and Octogen (HMX) based aluminized explosives. The percentage of the explosive varied from 5% to 30% and it is shown that: the shockwave peak pressure (pm) grows gradually; shock wave energy (Es) continues increasing, bubble energy (Eb) increases then decreases peaking at 15% for both formulas, and the total energy (E) and energy release rate (η) peak at 20% for CL-20 and 15% for HMX. This paper outlines the physical mechanism of Eb change under the influence of an aluminium initial reaction temperature and reaction active detonation product percentage coupling. The result shows that CL-20 is superior as a new high explosive and has promising application prospects in the regulation of explosive energy output for underwater explosives.

78 FR 64246 - Commerce in Explosives; List of Explosives Materials

Science.gov (United States)

2013-10-28

..., including non-cap sensitive slurry and water gel explosives. Blasting caps. Blasting gelatin. Blasting.... Explosive conitrates. Explosive gelatins. Explosive liquids. Explosive mixtures containing oxygen-releasing... powder. [[Page 64247

The effect of explosive percentage on underwater explosion energy release of hexanitrohexaazaisowurtzitane and octogen based aluminized explosives

OpenAIRE

Qingjie Jiao; Qiushi Wang; Jianxin Nie; Xueyong Guo; Wei Zhang; Wenqi Fan

2018-01-01

To control the explosion energy output by optimizing explosive components is a key requirement in a number of different application areas. The effect of different Al/O Ratio on underwater explosion of aluminized explosives has been studied detailedly. However, the effect of explosive percentage in the same Al/O Ratio is rarely researched, especially for Hexanitrohexaazaisowurtzitane (CL-20) based aluminized explosives. In this study, we performed the underwater explosion experiments with 1.2-...

Modelling of vapour explosion in a stratified geometry

International Nuclear Information System (INIS)

Brayer, Claude

1994-01-01

A vapour explosion is the explosive vaporisation of a volatile liquid in contact with another hotter liquid. Such a violent vaporisation requires an intimate mixing and a fine fragmentation of both liquids. Based on a synthesis of published experimental results, the author of this research thesis reports the development of a new physical model which describes the explosion. In this model, the explosion propagation is due to the propagation of the pressure wave associated with this this explosion, all along the vapour film which initially separates both liquids. The author takes the presence of water in the liquid initially located over the film into account. This presence of vapour explains experimental propagation rates. Another consequence, when the pressure wave passes, is an acceleration of liquids at different rates below and above the film. The author considers that a mixture layer then forms from the point of disappearance of the film, between both liquids, and that fragmentation is due to the turbulence in this mixture layer. This fragmentation model is then introduced into an Euler thermodynamic, three-dimensional and multi-constituents code of calculation, MC3D, to study the influence of fragmentation on thermal exchanges between the various constituents on the volatile liquid vaporisation [fr

Thermal interaction for molten tin dropped into water

International Nuclear Information System (INIS)

Arakeri, V.H.; Catton, I.; Kastenberg, W.E.; Plesset, M.S.

1978-01-01

Multiflash photography with extremely short duration exposure times per flash has been used to observe the interaction of molten tin dropped into a water bath. Detailed photographic evidence is presented which demonstrates that transition, or nucleate boiling, is a possible triggering mechanism for vapour explosions. It was also found that the thermal constraints required to produce vapour explosions could be relaxed by introducing a stable thermal stratification within the coolant. In the present work, the threshold value of the initial tin temperature required for vapour explosion was reduced from about 500 to 343 0 C. (author)

Detonation and fragmentation modeling for the description of large scale vapor explosions

International Nuclear Information System (INIS)

Buerger, M.; Carachalios, C.; Unger, H.

1985-01-01

The thermal detonation modeling of large-scale vapor explosions is shown to be indispensable for realistic safety evaluations. A steady-state as well as transient detonation model have been developed including detailed descriptions of the dynamics as well as the fragmentation processes inside a detonation wave. Strong restrictions for large-scale vapor explosions are obtained from this modeling and they indicate that the reactor pressure vessel would even withstand explosions with unrealistically high masses of corium involved. The modeling is supported by comparisons with a detonation experiment and - concerning its key part - hydronamic fragmentation experiments. (orig.) [de

Study of film boiling collapse behavior during vapor explosion

International Nuclear Information System (INIS)

Yagi, Masahiro; Yamano, Norihiro; Sugimoto, Jun; Abe, Yutaka; Adachi, Hiromichi; Kobayashi, Tomoyoshi.

1996-06-01

Possible large scale vapor explosions are safety concern in nuclear power plants during severe accident. In order to identify the occurrence of the vapor explosion and to estimate the magnitude of the induced pressure pulse, it is necessary to investigate the triggering condition for the vapor explosion. As a first step of this study, scooping analysis was conducted with a simulation code based on thermal detonation model. It was found that the pressure at the collapse of film boiling much affects the trigger condition of vapor explosion. Based on this analytical results, basic experiments were conducted to clarify the collapse conditions of film boiling on a high temperature solid ball surface. Film boiling condition was established by flooding water onto a high temperature stainless steel ball heated by a high frequency induction heater. After the film boiling was established, the pressure pulse generated by a shock tube was applied to collapse the steam film on the ball surface. As the experimental boundary conditions, materials and size of the balls, magnitude of pressure pulse and initial temperature of the carbon and stainless steel balls were varied. The transients of pressure and surface temperature were measured. It was found that the surface temperature on the balls sharply decreased when the pressure wave passed through the film on balls. Based on the surface temperature behavior, the film boiling collapse pattern was found to be categorized into several types. Especially, the pattern for stainless steel ball was categorized into three types; no collapse, collapse and reestablishment after collapse. It was thus clarified that the film boiling collapse behavior was identified by initial conditions and that the pressure required to collapse film boiling strongly depended on the initial surface temperature. The present results will provide a useful information for the analysis of vapor explosions based on the thermal detonation model. (J.P.N.)

Structures to Resist the Effects of Accidental Explosions. Volume 6. Special Considerations in Explosive Facility Design

Science.gov (United States)

1985-04-01

addition to their Inherent advantages with respect to fire protection, acoustical and thermal insulation, structural mass and resistance to flying...suspended from a monorail system. The panel is inside the shield and is not rigidly attached to the column members. Special consideration was given to...characteristic pulse emitted by an explosion to prevent actuation by other sources such as lightning, fires , etc., **ich cay occur with flash sensors. ■112

Strategies for the disposition of high explosives resulting from dismantlement of nuclear weapons

International Nuclear Information System (INIS)

Pruneda, C.; Humphrey, J.

1993-03-01

Many thousands of pounds of high quality main-charge explosives will result as surplus from the dismantlement of returns from the US nuclear weapons stockpile. The method most often employed for dealing with this surplus explosive is destruction by open burning. However, open burning as a means of treating excess explosives is losing favor because of environmental concerns associated with such an uncontrolled thermal destruction process. Thus, alternative processes for treatment of excess explosives from weapon dismantlement is discussed. These alternatives include: reformulation, crystalline component recovery, chemical conversion of the crystalline component to higher value products which may have civilian or military applications and, when necessary, treatment as waste in an environmentally benign fashion

Proceedings of the fourteenth annual symposium on explosives and blasting research

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-31

Subjects covered include: ground vibration effects on structures; open-pit blast vibration prediction; effects of velocity of detonation and gas pressurization on fragmentation in layered rock; thermal ignition for emulsion powder explosives and emulsion matrix; effect of cut-off pressure on energy partition and blast design; new burden and spacing formulae for optimum blasting; calculated risk of experiencing lightning caused unplanned detonation; predicting explosive toxic fumes; and stemming techniques for loading angled holes charged with Anfo.

Contained fissionly vaporized imploded fission explosive breeder reactor

International Nuclear Information System (INIS)

Marwick, E.F.

1978-01-01

Disclosed is a nuclear reactor system which produces useful thermal power and breeds fissile isotopes wherein large spherical complex slugs containing fissile and fertile isotopes as well as vaporizing and tamping materials are exploded seriatim in a large containing chamber having walls protected from the effects of the explosion by about two thousand tons of slurry of fissile and fertile isotopes in molten alkali metal. The slug which is slightly sub-critical prior to its entry into the centroid portion of the chamber, then becomes slightly more than prompt-critical because of the near proximity of neutron-reflecting atoms and of fissioning atoms within the slurry. The slurry is heated by explosion of the slugs and serves as a working fluid for extraction of heat energy from the reactor. Explosive debris is precipitated from the slurry and used for the fabrication of new slugs

High-temperature explosive development for geothermal well stimulation. Final report

Energy Technology Data Exchange (ETDEWEB)

Schmidt, E.W.; Mars, J.E.; Wang, C.

1978-03-31

A two-component, temperature-resistant liquid explosive called HITEX has been developed which is capable of withstanding 561/sup 0/K (550/sup 0/F) for 24 hours in a geothermal environment. The explosive is intended for the stimulation of nonproducing or marginally producing geothermal (hot dry rock, vapor-dominated or hydrothermal) reservoirs by fracturing the strata in the vicinity of a borehole. The explosive is inherently safe because it is mixed below ground downhole from two nondetonable liquid components. Development and safety tests included differential scanning calorimetry, thermal stability, minerals compatibility, drop-weight sensitivity, adiabatic compression, electrostatic discharge sensitivity, friction sensitivity, detonation arrest capability, cook-off tests, detonability at ambient and elevated pressure, detonation velocity and thin film propagation in a wedge.

Detection of explosives and illicit drugs using neutrons

Energy Technology Data Exchange (ETDEWEB)

Kiraly, B. E-mail: kiralyb@tigris.klte.hu; Sanami, T.; Doczi, R.; Csikai, J

2004-01-01

A procedure developed for the determination of the flux perturbation factor required for the thermal neutron activation analysis of bulky samples of unknown composition has been extended for epithermal neutrons using hydrogenous and graphite moderators. Measurements on the diffusion and backscattering of thermal neutrons in soil components were carried out for the development of novel nuclear methods in order to speed up the humanitarian demining process. Results obtained for the diffusion length were checked by MCNP-4C calculations. In addition, the effect of the weight and density of the explosives on the observation of the anomaly in the reflected thermal neutrons was examined by using different dummy landmines.

Design and construction of an explosive detection system by Tna methods, using 252Cf radioisotope source

International Nuclear Information System (INIS)

Tavakkoli Farsouli, A.

1999-01-01

Bombs concealed in luggage have threatened human life and property throughout the world's traffic. The plastic explosives could not checked by the X-ray detecting device. Thermal Neutron Activation method has been tested in the present work for non-destructive detection of explosives. A radioisotope neutron source 252 Cf and two gamma spectroscopy systems have been used as a tool to find explosives, regardless of the bomb's shape and the packing materials. The MCNP code has been used to design the neutronic section of the system. The measured thermal neutron fluxes by the gold foils in some location of the system were in good agreement with those data obtained by the MCNP code. Also, detection limits for nitrogen in various counting times were measured. The measurements show that the system is capable to detect 417 gr of HMX explosive material (158 gr nitrogen) by 10 minutes of counting time. To modify the system and to decrease the detection limits some opinions are given

Primary explosives

Energy Technology Data Exchange (ETDEWEB)

Matyas, Robert; Pachman, Jiri [Pardubice Univ. (Czech Republic). Faculty of Chemical Technology

2013-06-01

The first chapter provides background such as the basics of initiation and differences between requirements on primary explosives used in detonators and igniters. The authors then clarify the influence of physical characteristics on explosive properties, focusing on those properties required for primary explosives. Furthermore, the issue of sensitivity is discussed. All the chapters on particular groups of primary explosives are structured in the same way, including introduction, physical and chemical properties, explosive properties, preparation and documented use.

A thermodynamically based definition of fast verses slow heating in secondary explosives

Science.gov (United States)

Henson, Bryan; Smilowitz, Laura

2013-06-01

The thermal response of energetic materials is often categorized according to the rate of heating as either fast or slow, e.g. slow cook-off. Such categorizations have most often followed some operational rationale, without a material based definition. We have spent several years demonstrating that for the energetic material octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) a single mechanism of thermal response reproduces times to ignition independent of rate or means of heating over the entire range of thermal response. HMX is unique in that bulk melting is rarely observed in either thermal ignition or combustion. We have recently discovered a means of expressing this mechanism for HMX in a reduced form applicable to many secondary explosives. We will show that with this mechanism a natural definition of fast versus slow rates of heating emerges, related to the rate of melting, and we use this to illustrate why HMX does not exhibit melting, and why a number of other secondary explosives do, and require the two separate categories.

Steam explosions of single drops of pure and alloyed molten aluminum

International Nuclear Information System (INIS)

Nelson, L.S.

1995-01-01

Studies of steam explosion phenomena have been performed related to the hypothetical meltdown of the core and other components of aluminum alloy-fueled production reactors. Our objectives were to characterise the triggers, if any, required to initiate these explosions and to determine the energetics and chemical processes associated with these events. Three basic studies have been carried out with 1-10 g single drops of molten aluminum or aluminum-based alloys: untriggered experiments in which drops of melt were released into water; triggered experiments in which thermal-type steam explosions occurred; and one triggered experiment in which an ignition-type steam explosion occurred. In untriggered experiments, spontaneous steam explosions never occurred during the free fall through water of single drops of pure Al or of the alloys studied here. Moreover, spontaneous explosions never occurred upon or during contact of the globules with several underwater surfaces. When Li was present in the alloy, H 2 was generated as a stream of bubbles as the globules fell through the water, and also as they froze on the bottom surface of the chamber. The triggered experiments were performed with pure Al and the 6061 alloy. Bare bridgewire discharges and those focused with cylindrical reflectors produced a small first bubble that collapsed and was followed by a larger second bubble. When the bridgewire was discharged at one focus of an ellipsoidal reflector, a melt drop at the other focus triggered only very mildly in spite of a 30-fold increase in peak pressure above that of the bridgewire discharge without the reflector. Experiments were also performed with globules of high purity Al in which the melt release temperature was progressively increased. Moderate thermal-type explosions were produced over the temperature range 1273-1673 K. At about 1773 K, however, one experiment produced a brilliant flash of light and bubble growth about an order of magnitude faster than normal; it

Radioactive and Other Effects of Nuclear Explosion

International Nuclear Information System (INIS)

Ilijas, B.; Cizmek, A.; Prah, M.; Medakovic, S.

2008-01-01

As a result of long lasting efforts of international community to definitely ban all test nuclear explosions, the Comprehensive Nuclear-Test-Ban Treaty (CTBT) was opened for signature in New York on 24 September 1996, when it was signed by 71 states, including Croatia. The State Office for Nuclear Safety (SONS) which, as an independent state regulatory authority has a responsibility for activities relating to nuclear safety, including the national authority over this Treaty, is actively engaged in CTBTO activities. The nuclear explosion causes a lot of effects (blast, thermal, radioactive, electromagnetic) which differs a lot in its nature, reach, lasting and other. The longest lasting aftermath is from the radioactive effects that cause a radioactive fallout and a lot of radioactive elements in the environment, created by the influence of a primary beam of radiation. Fission and fusion are the main source of radionuclide created by the nuclear explosion, and the longest lasting aftermaths are by the fission products, namely their offspring in natural disintegration chains. This can make contaminated areas inappropriate for life for very long periods. Even in the case of underground nuclear explosion (when underground cavity is formed with no effects on the surface), a leakage of radioactive gases through cracks is possible. A number of radionuclide is created by the neutron activation of elements naturally present in an environment, because a very strong neutron radiation appears in the moment of nuclear explosion. The abundance of particular radionuclide is a very much dependent of a place of performing nuclear explosion and a composition of soil or water in the vicinity.(author)

Lower head integrity under steam explosion loads

Energy Technology Data Exchange (ETDEWEB)

Theofanous, T.G.; Yuen, W.W.; Angelini, S.; Freeman, K.; Chen, X.; Salmassi, T. [Center for Risk Studies and Safety, Univ. of California, Santa Barbara, CA (United States); Sienicki, J.J.

1998-01-01

Lower head integrity under steam explosion loads in an AP600-like reactor design is considered. The assessment is the second part of an evaluation of the in-vessel retention idea as a severe accident management concept, the first part (DOE/ID-10460) dealing with thermal loads. The assessment is conducted in terms of the Risk Oriented Accident Analysis Methodology (ROAAM), and includes the comprehensive evaluation of all relevant severe accident scenarios, melt conditions and timing of release from the core region, fully 3D mixing and explosion wave dynamics, and lower head fragility under local, dynamic loading. All of these factors and brought together in a ROAAM Probabilistic Framework to evaluate failure likelihood. The conclusion is that failure is `physically unreasonable`. (author)

Violence

Science.gov (United States)

... gov home / Home Relationships Dealing with conflict Violence Violence Violence among young people is a serious problem. ... according to a recent national survey Types of violence top Youth violence can include: Hitting, pinching, punching, ...

Analysis and modeling of flow blockage-induced steam explosion events in the High-Flux Isotope Reactor

International Nuclear Information System (INIS)

Taleyarkhan, R.P.; Georgevich, V.; Lestor, C.W.; Gat, U.; Lepard, B.L.; Cook, D.H.; Freels, J.; Chang, S.J.; Luttrell, C.; Gwaltney, R.C.; Kirkpatrick, J.

1993-01-01

This paper provides a perspective overview of the analysis and modeling work done to evaluate the threat from steam explosion loads in the High-Flux Isotope Reactor during flow blockage events. The overall workscope included modeling and analysis of core melt initiation, melt propagation, bounding and best-estimate steam explosion energetics, vessel failure from fracture, bolts failure from exceedance of elastic limits, and finally, missile evolution and transport. Aluminum ignition was neglected. Evaluations indicated that a thermally driven steam explosion with more than 65 MJ of energy insertion in the core region over several miliseconds would be needed to cause a sufficiently energetic missile with a capacity to cause early confinement failure. This amounts to about 65% of the HFIR core mass melting and participating in a steam explosion. Conservative melt propagation analyses have indicated that at most only 24% of the HFIR core mass could melt during flow blockage events under full-power conditions. Therefore, it is judged that the HFIR vessel and top head structure will be able to withstand loads generated from thermally driven steam explosions initiated by any credible flow blockage event. A substantial margin to safety was demonstrated

The scandal of manhood: 'Baby rape' and the politicization of sexual violence in post-apartheid South Africa.

Science.gov (United States)

Posel, Deborah

2005-05-01

This paper traces the genealogy of sexual violence as a public and political issue in South Africa, from its initial marginalization and minimization during the apartheid era, through to the explosion of anguish and anger which marked the post-apartheid moment, and most dramatically the years 2001 and 2002. Of particular interest is the question of how and why the problem of sexual violence came to be seen as a scandal of manhood, putting male sexuality under critical public scrutiny. The paper argues that the sudden, intense eruption of public anxiety and argument about sexual violence which marked the post-apartheid period had relatively little to do with feminist analysis and politics (influential though this has been in some other respects). Rather, the key to understanding this politicization of sexual violence lies with its resonances with wider political and ideological anxieties about the manner of the national subject and the moral community of the country's fledgling democracy.

Development of steam explosion simulation code JASMINE

Energy Technology Data Exchange (ETDEWEB)

Moriyama, Kiyofumi; Yamano, Norihiro; Maruyama, Yu; Kudo, Tamotsu; Sugimoto, Jun [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Nagano, Katsuhiro; Araki, Kazuhiro

1995-11-01

A steam explosion is considered as a phenomenon which possibly threatens the integrity of the containment vessel of a nuclear power plant in a severe accident condition. A numerical calculation code JASMINE (JAeri Simulator for Multiphase INteraction and Explosion) purposed to simulate the whole process of steam explosions has been developed. The premixing model is based on a multiphase flow simulation code MISTRAL by Fuji Research Institute Co. In JASMINE code, the constitutive equations and the flow regime map are modified for the simulation of premixing related phenomena. The numerical solution method of the original code is succeeded, i.e. the basic equations are discretized semi-implicitly, BCGSTAB method is used for the matrix solver to improve the stability and convergence, also TVD scheme is applied to capture a steep phase distribution accurately. Test calculations have been performed for the conditions correspond to the experiments by Gilbertson et al. and Angelini et al. in which mixing of solid particles and water were observed in iso-thermal condition and with boiling, respectively. (author).

Development of steam explosion simulation code JASMINE

International Nuclear Information System (INIS)

Moriyama, Kiyofumi; Yamano, Norihiro; Maruyama, Yu; Kudo, Tamotsu; Sugimoto, Jun; Nagano, Katsuhiro; Araki, Kazuhiro.

1995-11-01

A steam explosion is considered as a phenomenon which possibly threatens the integrity of the containment vessel of a nuclear power plant in a severe accident condition. A numerical calculation code JASMINE (JAeri Simulator for Multiphase INteraction and Explosion) purposed to simulate the whole process of steam explosions has been developed. The premixing model is based on a multiphase flow simulation code MISTRAL by Fuji Research Institute Co. In JASMINE code, the constitutive equations and the flow regime map are modified for the simulation of premixing related phenomena. The numerical solution method of the original code is succeeded, i.e. the basic equations are discretized semi-implicitly, BCGSTAB method is used for the matrix solver to improve the stability and convergence, also TVD scheme is applied to capture a steep phase distribution accurately. Test calculations have been performed for the conditions correspond to the experiments by Gilbertson et al. and Angelini et al. in which mixing of solid particles and water were observed in iso-thermal condition and with boiling, respectively. (author)

Predicting Large-scale Effects During Cookoff of Plastic-Bonded Explosives (PBX 9501 PBX 9502 and LX-14)

Energy Technology Data Exchange (ETDEWEB)

Hobbs, Michael L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kaneshige, Michael J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Erikson, William W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-10-01

In this study, we have made reasonable cookoff predictions of large-scale explosive systems by using pressure-dependent kinetics determined from small-scale experiments. Scale-up is determined by properly accounting for pressure generated from gaseous decomposition products and the volume that these reactive gases occupy, e.g. trapped within the explosive, the system, or vented. The pressure effect on the decomposition rates has been determined for different explosives by using both vented and sealed experiments at low densities. Low-density explosives are usually permeable to decomposition gases and can be used in both vented and sealed configurations to determine pressure-dependent reaction rates. In contrast, explosives that are near the theoretical maximum density (TMD) are not as permeable to decomposition gases, and pressure-dependent kinetics are difficult to determine. Ignition in explosives at high densities can be predicted by using pressure-dependent rates determined from the low-density experiments as long as gas volume changes associated with bulk thermal expansion are also considered. In the current work, cookoff of the plastic-bonded explosives PBX 9501 and PBX 9502 is reviewed and new experimental work on LX-14 is presented. Reactive gases are formed inside these heated explosives causing large internal pressures. The pressure is released differently for each of these explosives. For PBX 9501, permeability is increased and internal pressure is relieved as the nitroplasticizer melts and decomposes. Internal pressure in PBX 9502 is relieved as the material is damaged by cracks and spalling. For LX-14, internal pressure is not relieved until the explosive thermally ignites. The current paper is an extension of work presented at the 26th ICDERS symposium [1].

Thermal safety characterization on PETN, PBX-9407, LX-10-2, LX-17-1 and detonator in the LLNL's P-ODTX system

Energy Technology Data Exchange (ETDEWEB)

Hsu, P. C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Strout, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Reynolds, J. G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kahl, E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ellsworth, F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Healy, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-09-21

Incidents caused by fire and other thermal events can heat energetic materials that may lead to thermal explosion and result in structural damage and casualty. Thus, it is important to understand the response of energetic materials to thermal insults. The One-Dimensional-Time to Explosion (ODTX) system at the Lawrence Livermore National Laboratory (LLNL) has been used for decades to characterize thermal safety of energetic materials. In this study, an integration of a pressure monitoring element has been added into the ODTX system (P-ODTX) to perform thermal explosion (cook-off) experiments (thermal runaway) on PETN powder, PBX-9407, LX-10-2, LX-17-1, and detonator samples (cup tests). The P-ODTX testing generates useful data (thermal explosion temperature, thermal explosion time, and gas pressures) to assist with the thermal safety assessment of relevant energetic materials and components. This report summarizes the results of P-ODTX experiments that were performed from May 2015 to July 2017. Recent upgrades to the data acquisition system allows for rapid pressure monitoring in microsecond intervals during thermal explosion. These pressure data are also included in the report.

Gas explosions and thermal runaways during external heating abuse of commercial lithium-ion graphite-LiCoO2 cells at different levels of ageing

Science.gov (United States)

Larsson, Fredrik; Bertilsson, Simon; Furlani, Maurizio; Albinsson, Ingvar; Mellander, Bengt-Erik

2018-01-01

Commercial 6.8 Ah lithium-ion cells with different ageing/status have been abused by external heating in an oven. Prior to the abuse test, selected cells were aged either by C/2 cycling up to 300 cycles or stored at 60 °C. Gas emissions were measured by FTIR and three separate vents were identified, two well before the thermal runaway while the third occurred simultaneously with the thermal runaway releasing heavy smoke and gas. Emissions of toxic carbon monoxide (CO), hydrogen fluoride (HF) and phosphorous oxyfluoride (POF3) were detected in the third vent, regardless if there was a fire or not. All abused cells went into thermal runaway and emitted smoke and gas, the working cells also released flames as well as sparks. The dead cells were however less reactive but still underwent thermal runaway. For about half of the working cells, for all levels of cycle ageing, ignition of the accumulated battery released gases occurred about 15 s after the thermal runaway resulting in a gas explosion. The thermal runaway temperature, about 190 °C, varied somewhat for the different cell ageing/status where a weak local minimum was found for cells cycled between 100 and 200 times.

Chemical and physical modification of hemp fibres by steam explosion technology

International Nuclear Information System (INIS)

Sutka, Anna; Kukle, Silvija; Gravitis, Janis; Berzins, Agris

2013-01-01

In current research attempt has been made to analyse hemp fibres treated with steam explosion (SE) technology. Disintegration of hemp fibres separated from non-retted, dew-retted and dried stems of hemp ('Purini')[1] by alkali treatment and steam explosion (SE) were investigated. An average intensive SE in combination with the hydro-thermal and alkali after-treatment allows decreasing the diameter of hemp fibres and reduce the concentration of non-celluloses components, among them hemicelluloses, lignin, pectin, waxes and water [1;2

The Air Blast Wave from a Nuclear Explosion

Science.gov (United States)

Reines, Frederick

The sudden, large scale release of energy in the explosion of a nuclear bomb in air gives rise, in addition to nuclear emanations such as neutrons and gamma rays, to an extremely hot, rapidly expanding mass of air.** The rapidly expanding air mass has an initial temperature in the vicinity of a few hundred thousand degrees and for this reason it glows in its early stages with an intensity of many suns. It is important that the energy density in this initial "ball of fire" is of the order of 3 × 103 times that found in a detonating piece of TNT and hence that the initial stages of the large scale air motion produced by a nuclear explosion has no counterpart in an ordinary. H. E. explosion. Further, the relatively low temperatures ˜2,000°C associated with the initial stages of an H. E. detonation implies that the thermal radiation which it emits is a relatively insignificant fraction of the total energy involves. This point is made more striking when it is remembered that the thermal energy emitted by a hot object varies directly with the temperature in the Rayleigh Jeans region appropriate to the present discussion. The expansion of the air mass heated by the nuclear reaction produces, in qualitatively the same manner as in an H.E. explosion or the bursting of a high pressure balloon, an intense sharp pressure pulse, a shock wave, in the atmosphere. As the pressure pulse spreads outward it weakens due to the combined effects of divergence and the thermodynamically irreversible nature of the shock wave. The air comprising such a pressure pulse or blast wave moves first radially outward and then back towards the center as the blast wave passes. Since a permanent outward displacement of an infinite mass of air would require unlimited energy, the net outward displacement of the air distant from an explosion must approach zero with increasing distance. As the distance from the explosion is diminished the net outward displacement due to irreversible shock heating of

Progress in model development to quantify High Explosive Violent Response (HEVR) to mechanical insult

International Nuclear Information System (INIS)

Reaugh, J.E.

2008-01-01

The rapid release of chemical energy has found application for industrial and military purposes since the invention of gunpowder. Black powder, smokeless powder of various compositions, and pyrotechnics all exhibit the rapid release of energy without detonation when they are being used as designed. The rapidity of energy release for these materials is controlled by adjustments to the particle surface area (propellant grain configuration or powder particle size) in conjunction with the measured pressure-dependent burning rate, which is very subsonic. In this way a manufacturing process can be used to engineer the desired violence of the explosion. Detonations in molecular explosives, in contrast, propagate with a supersonic velocity that depends on the loading density, but is independent of the surface area. In ideal detonations, the reaction is complete within a small distance of the propagating shock front. Non-ideal detonations in molecular and composite explosives proceed with a slower velocity, and the reaction may continue well behind the shock front. We are developing models to describe the circumstances when molecular and composite explosives undergo a rapid release of energy without detonating. The models also apply to the behavior of rocket propellants subject to mechanical insult, whether for accidents (Hazards) or the suite of standardized tests used to assess whether the system can be designated an Insensitive Munition (IM). In the application described here, we are studying an HMX (1,3,5,7-tetranitro-1,3,5,7-tetraazacyclooctane) explosive developed in the UK, which is 91% by weight HMX and 9% binder-plasticizer. Most explosives and propellants, when subjected to a mechanical insult, drop or impact that is well below the threshold for detonation have been observed to react violently. This behavior is known as High Explosive Violent Reaction (HEVR). The basis of our model is the observation that the mechanical insult produces damage in a volume of the

Investigation on energetics of ex-vessel vapor explosion based on spontaneous nucleation fragmentation

International Nuclear Information System (INIS)

Liu, Jie; Koshizuka, Seiichi; Oka, Yoshiaki

2002-01-01

A computer code PROVER-I is developed for propagation phase of vapor explosion. A new thermal fragmentation model is proposed with three kinds of time scale for modeling instant fragmentation, spontaneous nucleation fragmentation and normal boiling fragmentation. The energetics of ex-vessel vapor explosion is investigated based on different fragmentation models. A higher pressure peak and a larger mechanical energy conversion ratio are obtained by spontaneous nucleation fragmentation. A smaller energy conversion ratio results from normal boiling fragmentation. When the delay time in thermal fragmentation model is near 0.0 ms, the pressure propagation behavior tends to be analogous with that in hydrodynamic fragmentation. If the delay time is longer, pressure attenuation occurs at the shock front. The high energy conversion ratio (>4%) is obtained in a small vapor volume fraction together with spontaneous nucleation fragmentation. These results are consistent with fuel-coolant interaction experiments with alumina melt. However, in larger vapor volume fraction conditions (α υ >0.3), the vapor explosion is weak. For corium melt, a coarse mixture with void fraction of more than 30% can be generated in the pre-mixing process because of its physical properties. In the mixture with such a high void fraction the energetic vapor explosion hardly takes place. (author)

Verification of fire and explosion accident analysis codes (facility design and preliminary results)

International Nuclear Information System (INIS)

Gregory, W.S.; Nichols, B.D.; Talbott, D.V.; Smith, P.R.; Fenton, D.L.

1985-01-01

For several years, the US Nuclear Regulatory Commission has sponsored the development of methods for improving capabilities to analyze the effects of postulated accidents in nuclear facilities; the accidents of interest are those that could occur during nuclear materials handling. At the Los Alamos National Laboratory, this program has resulted in three computer codes: FIRAC, EXPAC, and TORAC. These codes are designed to predict the effects of fires, explosions, and tornadoes in nuclear facilities. Particular emphasis is placed on the movement of airborne radioactive material through the gaseous effluent treatment system of a nuclear installation. The design, construction, and calibration of an experimental ventilation system to verify the fire and explosion accident analysis codes are described. The facility features a large industrial heater and several aerosol smoke generators that are used to simulate fires. Both injected thermal energy and aerosol mass can be controlled using this equipment. Explosions are simulated with H 2 /O 2 balloons and small explosive charges. Experimental measurements of temperature, energy, aerosol release rates, smoke concentration, and mass accumulation on HEPA filters can be made. Volumetric flow rate and differential pressures also are monitored. The initial experiments involve varying parameters such as thermal and aerosol rate and ventilation flow rate. FIRAC prediction results are presented. 10 figs

Research on the fundamental process of thermal-hydraulic behaviors in severe accident. Estimation of trigger condition for vapor explosion. JAERI's nuclear research promotion program, H10-027-1. Contract research

International Nuclear Information System (INIS)

Nariai, Hideki

2002-03-01

The experimental and analytical researches were conducted to study melted core material and coolant interaction including solidification and vapor explosion which is one of the most unidentified thermal hydraulic phenomena during sever accident of nuclear reactor. At first, the effect of the material properties on vapor explosion and solidification was examined to clarify the dominant factors for the spontaneous vapor explosion. Next, the interfacial phenomena of the high temperature melt material and violent boiling behavior of water at the interface was visually observed in the experiment. The interfacial phenomena were physically modeled. Finally, trigger phenomena from liquid-liquid contact to atomization were clarified through the forced collapse experiment of vapor film around a molten droplet by using pressure wave generation device. It is indicated by applying the results obtained in the present study to the actual reactor conditions that the possibility of the vapor explosion is extremely unlikely in the actual reactor accident sequence, since the surface of the molten uranium oxide is solidified in the water and the liquid-liquid contact can not be achieved. It should be noted that the decrease of the solidified temperature by metal compounds and the increase of the molten core temperature. (author)

New ANFO explosives made of ammonium nitrate of increased porosity and naphtha

Energy Technology Data Exchange (ETDEWEB)

Kutsarov, B.; Mavrodieva, R.; Ivanov, I.; Stoyanov, V.; Georgiev, N.; Krumov, I.; Katsarski, I.; Vakliev, I.

1990-01-01

Discusses results achieved by the KNIIPPI Niproruda Research Institute and the Osogovo enterprise in improving the quality of ANFO explosives. Ammonium nitrate with increased porosity was treated by water steam and wetting agents and then thermally treated. Naphtha in a quantity of up to 8% was then added to the ammonium nitrate to produce a powerful and stable explosive. The quality of explosive cartridges was tested first in the laboratory using the Schaffler apparatus. Test results were very satisfactory (better porosity, higher detonation velocity (2200-3600 m/s), better stability). Industrial experiments carried out in several underground mines also produced satisfactory results (better output in roadway drivage at lower operating cost and better safety). 8 refs.

Vapor explosion studies for nuclear and non-nuclear industries

Energy Technology Data Exchange (ETDEWEB)

Taleyarkhan, Rusi P. [Arden L. Bement, Jr. Professor Nuclear Engineering, School of Nuclear Engineering, 1290 Nuclear Engineering Building, Room 108C, Purdue University, West Lafayette, IN 47905 (United States)]. E-mail: rusi@purdue.edu

2005-05-01

Energetic melt-water explosions are a well-established contributor to risk for nuclear reactors, and even more so for the metal casting industry. In-depth studies were undertaken in an industry-national laboratory collaborative effort to understand the root causes of explosion triggering and to evaluate methods for prevention. The steam explosion triggering studies (SETS) facility was devised and implemented for deriving key insights into explosion prevention. Data obtained indicated that onset of base surface-entrapment induced explosive boiling-caused trigger shocks is a result of complex combination of surface wettability, type of coating (organic versus inorganic), degree of coating wearoff, existence of bypass pathways for pressure relief, charring and non-condensable gas (NCG) release potential. Of these parameters NCGs were found to play a preeminent role on explosion prevention by stabilizing the melt-water steam interface and acting as a shock absorber. The role of NCGs was experimentally confirmed using SETS for their effect on stable film boiling using a downward facing heated body through which gases were injected. The presence of NCGs in the steam film layer caused a significant delay in the transitioning of film-to-nucleate boiling. The role of NCGs on explosion prevention was thereafter demonstrated more directly by introducing molten metal drops into water pools with and without NCG bubbling. Whereas spontaneous and energetic explosions took place without NCG injection, only benign quenching occurred in the presence of NCGs. Gravimetric analyses of organic coatings which are known to prevent explosion onset were also found to release significant NCGs during thermal attack by melt in the presence of water. These findings offer a novel, simple, cost-effective technique for deriving fundamental insights into melt-water explosions as well as for explosion prevention under most conditions of interest to metal casting, and possibly for nuclear reactor

Self-ignition of explosive substance. Comparison between analytical and numerical calculations in order to optimize safety in a pyrotechnic context; Auto-inflammation de substances explosives. Comparaison entre calcul analytique et numerique en vue d`une optimisation dans le domaine de la pyrotechnie

Energy Technology Data Exchange (ETDEWEB)

Gillard, Ph. [Centre National de la Recherche Scientifique (CNRS), 86 - Poitiers (France)

1998-04-01

Self-ignition of energetic material was investigated in order to optimize safety in the field of pyrotechnic applications. Two approaches were used; the first one is relative to Frank-Kamenetskii stationary thermal explosion theory. The second approach consists of a choice of some numerical solutions of heat conduction equations in a non-stationary state. Comparison between these results was carried out in order to find the numerical scheme which is the most compatible with Frank-Kamenetskii stationary thermal explosion theory. Numerical data were used for three explosive substances. One of them was studied by the author. In all cases, the numerical stationary state is in agreement with the Frank-Kamenetskii stationary thermal explosion theory, more or less accurately. From this comparison, it may be concluded that it is preferable, for this kind of problem, to use an implicit scheme with linearization of the heat source term. Explicit numerical methods, with or without the addition of the heat term with the Zinn and Mader scheme are revealed to be less accurate and to need a greater optimization of spatial and temporal meshing. (author) 7 refs.

Gas explosion in domestic buildings. The vented gas explosion[sub][/sub

Directory of Open Access Journals (Sweden)

Tadeusz Chyży

2014-08-01

Full Text Available In this paper, the basic information, related to the so-called vented gas explosion, has been presented. The vented explosion it is an explosion, during which the destruction of the weakest elements of the structure occurs. Through the resulting holes (decompressing surfaces can flow both combustion products and non-burned gas mixture. In consequence, reduction of the maximum explosion pressure[i] P[sub]red [/sub][/i] may be significant. Often, a gas explosion occurs inside residential buildings. In this case, natural vents are window and door openings.[b]Keywords[/b]: gas, explosion, combustion, explosion vents

Witnessing Interparental Violence and Acceptance of Dating Violence as Predictors for Teen Dating Violence Victimization.

Science.gov (United States)

Karlsson, Marie E; Temple, Jeff R; Weston, Rebecca; Le, Vi Donna

2016-04-01

We examined the association between witnessing interparental violence, attitudes about dating violence, and physical and psychological teen dating violence (TDV) victimization. Participants were 918 teens with dating experience. Witnessing interparental violence and acceptance of dating violence were significant predictors of TDV victimization. Acceptance of dating violence was also a partial mediator between witnessing interparental violence and TDV victimization. Witnessing mother-to-father violence and acceptance of female-perpetrated violence were the most consistent predictors. TDV programs aiming to prevent victimization could benefit from targeting youth exposed to father-to-mother and mother-to-father violence, targeting attitudes about violence, and tailoring interventions to gender-specific risk factors. © The Author(s) 2015.

Television Violence: Implications for Violence Prevention.

Science.gov (United States)

Hughes, Jan N.; Hasbrouck, Jan E.

1996-01-01

Reviews the scientific and public-opinion debate on the impact television violence in America has on aggression and violence. Research supports the view that television violence contributes to children's level of aggressiveness and subsequent violence and criminality. Describes attempts to improve the quality of television programming for children…

A TNA explosives-detection system in airline baggage

Energy Technology Data Exchange (ETDEWEB)

Shea, P.; Gozani, T. (Science Applications International Corp., Santa Clara, CA (USA)); Bozorgmanesh, H. (Science Applications International Corp., San Diego, CA (USA))

1990-12-20

Existing technologies that are applied to explosives-detection in passenger baggage are briefly discussed. A system based on thermal-neutron analysis (TNA) is described. The actual performance of the system in the field on passenger bags is given. The application of the TNA in an integrated airport security system is discussed in view of the intense public debate on this issue. (orig.).

Ex-Vessel corium coolability and steam explosion energetics in nordic light water reactors

International Nuclear Information System (INIS)

Dinh, T.N.; Ma, W.M.; Karbojian, A.; Kudinov, P.; Tran, C.T.; Hansson, C.R.

2008-03-01

This report presents advances and insights from the KTH's study on corium pool heat transfer in the BWR lower head; debris bed formation; steam explosion energetics; thermal hydraulics and coolability in bottom-fed and heterogeneous debris beds. Specifically, for analysis of heat transfer in a BWR lower plenum an advanced threedimensional simulation tool was developed and validated, using a so-called effective convectivity approach and Fluent code platform. An assessment of corium retention and coolability in the reactor pressure vessel (RPV) lower plenum by means of water supplied through the Control Rod Guide Tube (CRGT) cooling system was performed. Simulant material melt experiments were performed in an intermediate temperature range (1300-1600K) on DEFOR test facility to study formation of debris beds in high and low subcooled water pools characteristic of in-vessel and ex-vessel conditions. Results of the DEFOR-E scoping experiments and related analyses strongly suggest that porous beds formed in ex-vessel from a fragmented high-temperature debris is far from homogeneous. Calculation results of bed thermal hydraulics and dryout heat flux with a two-dimensional thermal-hydraulic code give the first basis to evaluate the extent by which macro and micro inhomogeneity can enhance the bed coolability. The development and validation of a model for two-phase natural circulation through a heated porous medium and its application to the coolability analysis of bottom-fed beds enables quantification of the significant effect of dryout heat flux enhancement (by a factor of 80-160%) due to bottom coolant injection. For a qualitative and quantitative understanding of steam explosion, the SHARP system and its image processing methodology were used to characterize the dynamics of a hot liquid (melt) drop fragmentation and the volatile liquid (coolant) vaporization. The experimental results provide a basis to suggest that the melt drop preconditioning is instrumental to the

Ex-Vessel corium coolability and steam explosion energetics in nordic light water reactors

Energy Technology Data Exchange (ETDEWEB)

Dinh, T.N.; Ma, W.M.; Karbojian, A.; Kudinov, P.; Tran, C.T.; Hansson, C.R. [Royal Institute of Technology (KTH), (Sweden)

2008-03-15

This report presents advances and insights from the KTH's study on corium pool heat transfer in the BWR lower head; debris bed formation; steam explosion energetics; thermal hydraulics and coolability in bottom-fed and heterogeneous debris beds. Specifically, for analysis of heat transfer in a BWR lower plenum an advanced threedimensional simulation tool was developed and validated, using a so-called effective convectivity approach and Fluent code platform. An assessment of corium retention and coolability in the reactor pressure vessel (RPV) lower plenum by means of water supplied through the Control Rod Guide Tube (CRGT) cooling system was performed. Simulant material melt experiments were performed in an intermediate temperature range (1300-1600K) on DEFOR test facility to study formation of debris beds in high and low subcooled water pools characteristic of in-vessel and ex-vessel conditions. Results of the DEFOR-E scoping experiments and related analyses strongly suggest that porous beds formed in ex-vessel from a fragmented high-temperature debris is far from homogeneous. Calculation results of bed thermal hydraulics and dryout heat flux with a two-dimensional thermal-hydraulic code give the first basis to evaluate the extent by which macro and micro inhomogeneity can enhance the bed coolability. The development and validation of a model for two-phase natural circulation through a heated porous medium and its application to the coolability analysis of bottom-fed beds enables quantification of the significant effect of dryout heat flux enhancement (by a factor of 80-160%) due to bottom coolant injection. For a qualitative and quantitative understanding of steam explosion, the SHARP system and its image processing methodology were used to characterize the dynamics of a hot liquid (melt) drop fragmentation and the volatile liquid (coolant) vaporization. The experimental results provide a basis to suggest that the melt drop preconditioning is instrumental to

Aggressiveness, violence, homicidality, homicide, and Lyme disease

Directory of Open Access Journals (Sweden)

Bransfield RC

2018-03-01

Full Text Available Robert C Bransfield Department of Psychiatry, Rutgers-Robert Wood Johnson Medical School, Piscataway, NJ, USA Background: No study has previously analyzed aggressiveness, homicide, and Lyme disease (LD. Materials and methods: Retrospective LD chart reviews analyzed aggressiveness, compared 50 homicidal with 50 non-homicidal patients, and analyzed homicides. Results: Most aggression with LD was impulsive, sometimes provoked by intrusive symptoms, sensory stimulation or frustration and was invariably bizarre and senseless. About 9.6% of LD patients were homicidal with the average diagnosis delay of 9 years. Postinfection findings associated with homicidality that separated from the non-homicidal group within the 95% confidence interval included suicidality, sudden abrupt mood swings, explosive anger, paranoia, anhedonia, hypervigilance, exaggerated startle, disinhibition, nightmares, depersonalization, intrusive aggressive images, dissociative episodes, derealization, intrusive sexual images, marital/family problems, legal problems, substance abuse, depression, panic disorder, memory impairments, neuropathy, cranial nerve symptoms, and decreased libido. Seven LD homicides included predatory aggression, poor impulse control, and psychosis. Some patients have selective hyperacusis to mouth sounds, which I propose may be the result of brain dysfunction causing a disinhibition of a primitive fear of oral predation.Conclusion: LD and the immune, biochemical, neurotransmitter, and the neural circuit reactions to it can cause impairments associated with violence. Many LD patients have no aggressiveness tendencies or only mild degrees of low frustration tolerance and irritability and pose no danger; however, a lesser number experience explosive anger, a lesser number experience homicidal thoughts and impulses, and much lesser number commit homicides. Since such large numbers are affected by LD, this small percent can be highly significant. Much of the

Use of artificial neural networks in drug and explosive detection through tomographic images with thermal neutrons

International Nuclear Information System (INIS)

Ferreira, Francisco J.O.; Crispim, Verginia R.; Silva, Ademir X.

2009-01-01

The artificial neural network technique was used to identify drugs and plastic explosives, from a tomography composed by a set of six neutrongraphic projections obtained in real time. Bidimensional tomographic images of samples of drugs, explosives and other materials, when digitally processed, yield the characteristic spectra of each type of material. The information contained in those spectra was then used for ANN training, the best images being obtained when the multilayer perceptron model, the back-propagation training algorithm and the Cross-validation interruption criterion were used. ANN showed to be useful in forecasting presence of drugs and explosives hitting a rate of success above 97 %. (author)

General phenomenology of underground nuclear explosions; Phenomenologie generale des explosions nucleaires souterraines

Energy Technology Data Exchange (ETDEWEB)

Derlich, S; Supiot, F [Commissariat a l' Energie Atomique, Bruyeres-le-Chatel (France). Centre d' Etudes

1969-07-01

An essentially qualitatively description is given of the phenomena related to underground nuclear explosions (explosion of a single unit, of several units in line, and simultaneous explosions). In the first chapter are described the phenomena which are common to contained explosions and to explosions forming craters (formation and propagation of a shock-wave causing the vaporization, the fusion and the fracturing of the medium). The second chapter describes the phenomena related to contained explosions (formation of a cavity with a chimney). The third chapter is devoted to the phenomenology of test explosions which form a crater; it describes in particular the mechanism of formation and the different types of craters as a function of the depth of the explosion and of the nature of the ground. The aerial phenomena connected with explosions which form a crater: shock wave in the air and focussing at a large distance, and dust clouds, are also dealt with. (authors) [French] On donne une description essentiellement qualitative des phenomenes lies aux explosions nucleaires souterraines (explosion d'un seul engin, d'engins en ligne et explosions simultanees). Dans un premier chapitre sont decrits les phenomenes communs aux explosions contenues et aux explosions formant un cratere (formation et propagation d'une onde de choc provoquant la vaporisation, la fusion et la fracturation du milieu). Le deuxieme chapitre decrit les phenomenes lies aux tirs contenus (formation d'une cavite et d'une cheminee). Le troisieme chapitre est consacre a la phenomenologie des tirs formant un cratere et decrit notamment le mecanisme de formation et les differents types de crateres en fonction de la profondeur d'explosion et de la nature du terrain. Les phenomenes aeriens lies aux explosions formant un cratere: onde de pression aerienne et focalisation a grande distance, nuages de poussieres, sont egalement abordes. (auteurs)

Computer simulation of explosion crater in dams with different buried depths of explosive

Science.gov (United States)

Zhang, Zhichao; Ye, Longzhen

2018-04-01

Based on multi-material ALE method, this paper conducted a computer simulation on the explosion crater in dams with different buried depths of explosive using LS-DYNA program. The results turn out that the crater size increases with the increase of buried depth of explosive at first, but closed explosion cavity rather than a visible crater is formed when the buried depth of explosive increases to some extent. The soil in the explosion cavity is taken away by the explosion products and the soil under the explosion cavity is compressed with its density increased. The research can provide some reference for the anti-explosion design of dams in the future.

Small-scale deflagration cylinder test with velocimetry wall-motion diagnostics

Energy Technology Data Exchange (ETDEWEB)

Hooks, Daniel E [Los Alamos National Laboratory; Hill, Larry G [Los Alamos National Laboratory; Pierce, Timothy H [Los Alamos National Laboratory

2010-01-01

Predicting the likelihood and effects of outcomes resultant from thermal initiation of explosives remains a significant challenge. For certain explosive formulations, the general outcome can be broadly predicted given knowledge of certain conditions. However, there remain unexplained violent events, and increased statistical understanding of outcomes as a function of many variables, or 'violence categorization,' is needed. Additionally, the development of an equation of state equivalent for deflagration would be very useful in predicting possible detailed event consequences using traditional hydrodynamic detonation moders. For violence categorization, it is desirable that testing be efficient, such that it is possible to statistically define outcomes reliant on the processes of initiation of deflagration, steady state deflagration, and deflagration to detonation transitions. If the test simultaneously acquires information to inform models of violent deflagration events, overall predictive capabilities for event likelihood and consequence might improve remarkably. In this paper we describe an economical scaled deflagration cylinder test. The cyclotetramethylene tetranitramine (HMX) based explosive formu1lation PBX 9501 was tested using different temperature profiles in a thick-walled copper cylindrical confiner. This test is a scaled version of a recently demonstrated deflagration cylinder test, and is similar to several other thermal explosion tests. The primary difference is the passive velocimetry diagnostic, which enables measurement of confinement vessel wall velocities at failure, regardless of the timing and location of ignition.

Study of the reactivity of an aggregative explosive sensitized by dynamical damage; Etude de la reactivite d`un explosif agregataire sensibilise par endommagement dynamique

Energy Technology Data Exchange (ETDEWEB)

Pertuis, Ch

1997-11-13

The thermal decomposition of a TATB-based explosive that have been exposed to a projectile impact, is studied in order to determine its sensitivity based on the morphological state of the damaged material. Two self-maintained thermal decomposition modes have been identified, one is a slow mode, the other is a rapid mode; four media have been differentiated in the damaged explosive: sound, porous, micro-cracked and fractured media, and thermal decomposition is studied for each media, using two experimental techniques, manometric bomb and a specifically designed strand burner. Laws giving the regression speed of each media has been established considering confinement pressure and initial temperature of the explosive. Analytical calculations yield the regression speed evolution as a function of certain parameters

Effect of Ti and C particle sizes on reaction behavior of thermal explosion reaction of Cu−Ti−C system under Ar and air atmospheres

Energy Technology Data Exchange (ETDEWEB)

Liang, Yunhong; Zhao, Qian; Li, Xiujuan; Zhang, Zhihui, E-mail: zhzh@jlu.edu.cn; Ren, Luquan

2016-09-15

The thermal explosion (TE) reaction behavior of Cu−Ti−C systems with different Ti and C particle sizes was investigated under air and Ar atmospheres. It was found that increasing the Ti and C particle sizes leads to higher ignition temperatures under both atmospheres and that the maximum combustion temperature decreases with increasing C particle size. The TE reaction is much easier to activate (i.e., it has a lower ignition temperature) in air because of the heat released from Ti oxidation and nitridation and Cu oxidation reactions on the Cu−Ti−C compact surface. TiC ceramic particles are successfully prepared in the bulk Cu−Ti−C compacts under both air and Ar atmospheres through a dissolution-diffusion-precipitation mechanism. Differential thermal and thermodynamic analyses show that the TE reaction ignition process in air is mainly controlled by the Ti particle size. - Highlights: • Variation of Ti and C particle sizes affects thermal reaction (TE) behaviors. • Ignition temperature under air is much lower than that under Ar atmosphere. • Heat of oxidation and nitridation reactions reduces ignition temperature under air.

Research on the fundamental process of thermal-hydraulic behaviors in severe accident. Estimation of trigger condition for vapor explosion. JAERI's nuclear research promotion program, H10-027-1. Contract research

Energy Technology Data Exchange (ETDEWEB)

Nariai, Hideki [Tsukuba Univ., Institute of Engineering Mechanics and Systems, Tsukuba, Ibaraki (Japan)

2002-03-01

The experimental and analytical researches were conducted to study melted core material and coolant interaction including solidification and vapor explosion which is one of the most unidentified thermal hydraulic phenomena during sever accident of nuclear reactor. At first, the effect of the material properties on vapor explosion and solidification was examined to clarify the dominant factors for the spontaneous vapor explosion. Next, the interfacial phenomena of the high temperature melt material and violent boiling behavior of water at the interface was visually observed in the experiment. The interfacial phenomena were physically modeled. Finally, trigger phenomena from liquid-liquid contact to atomization were clarified through the forced collapse experiment of vapor film around a molten droplet by using pressure wave generation device. It is indicated by applying the results obtained in the present study to the actual reactor conditions that the possibility of the vapor explosion is extremely unlikely in the actual reactor accident sequence, since the surface of the molten uranium oxide is solidified in the water and the liquid-liquid contact can not be achieved. It should be noted that the decrease of the solidified temperature by metal compounds and the increase of the molten core temperature. (author)

Features of the Valorization of Single and Double Based Powders for Codetonation in Emulsion Explosives

Science.gov (United States)

Ribeiro, Jose; Mendes, Ricardo; Tavares, Bruno; Louro, Cristina

2013-06-01

In this work, features of the thermal and detonation behavior of compositions resulting from the mixture of single and double based gun powder within ammonium nitrate (AN) based emulsion explosives are shown. That includes results of thermodynamic-equilibrium calculations of the detonation velocity, the chemical compatibility assessment through differential scanning calorimetry [DSC] and thermo gravimetric analysis [TGA], the experimental determination of the detonation velocity and a comparative evaluation of the shock sensitivity using a modified version of the ``gap-test''. DSC/TGA results for the compositions and for the individual components overlap until the beginning of the thermal decomposition which is an indication of the absence of formation of any new chemical specimens and so of the capability of the composition components. After the beginning of the thermal decomposition it can be seen that the rate of mass loss is much higher for the compositions with gun powder than for the sole emulsion explosive. Both, theoretical and experimental, values of the detonation velocity have shown to be higher for the powdered compositions than for the pure emulsion explosive. Shock sensitivity assessment have ended-up with a slightly bigger sensitivity for the compositions with double based gun powder when compared to the single based compositions or to the pure emulsion.

Preliminary analysis of K-DEMO thermal hydraulic system using MELCOR; Parametric study of hydrogen explosion

Energy Technology Data Exchange (ETDEWEB)

Moon, Sung Bo; Lim, Soo Min; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of)

2016-10-15

K-DEMO (Korean fusion demonstration reactor) is future reactor for the commercializing the fusion power generation. The Design of K-DEMO is similar to that of ITER but the fusion energy generation is much bigger because ITER is experimental reactor. For this reason, K-DEMO uses more fusion reaction with bigger amount of tritium. Higher fusion power means more neutron generation that can irradiate the structure around fusion plasma. Fusion reactor can produce many kinds of radioactive material in the accident. Because of this hazard, preliminary safety analysis is mandatory before its construction. Concern for safety problem of accident of fusion/fission reactor has been growing after Fukushima accident which is severe accident from unexpected disaster. To model the primary heat transfer system, in this study, MARS-KS thermal hydraulic analysis is referred. Lee et al. and Kim et al. conducted thermal hydraulic analysis using MARS-KS and multiple module simulation to deal with the phenomena of first wall corrosion for each plasma pulse. This study shows the relationship between vacuum vessel rupture area and source term leakage after hydrogen explosion. For the conservative study, first wall heating is not terminated because the heating inside the vacuum vessel increase the pressure inside VV. Pressurizer, steam generator and turbine is not damaged. 6.69 kg of tritiated water (HTO) and 1 ton of dust is modeled which is ITER guideline. The entire system of K-DEMO is smaller than that of ITER. For this reason, lots of aerosol is release into environment although the safety system like DS is maintained. This result shows that the safety system of K-DEMO should use much more safety system.

Explosion bonding of dissimilar materials for fabricating APS front end components: Analysis of metallurgical and mechanical properties and UHV applications

International Nuclear Information System (INIS)

Li, Yuheng; Shu, Deming; Kuzay, T.M.

1994-01-01

The front end beamline section contains photon shutters and fixed masks. These components are made of OFHC copper and GlidCOP AL-15. Stainless steels (304 or 316) are also used for connecting photon shutters and fixed masks to other components that operate in the ultrahigh vacuum system. All these dissimilar materials need to be joined together. However, bonding these dissimilar materials is very difficult because of their different mechanical and thermal properties and incompatible metallurgical properties. Explosion bonding is a bonding method in which the controlled energy of a detonating explosive is used to create a metallurgical bond between two or more similar or dissimilar materials. No intermediate filler metal, for example, a brazing compound or soldering alloy, is needed to promote bonding, and no external heat need be applied. A study of the metallurgical and mechanical properties and YGV applications of GlidCop AL-15, OFHC copper, and 304 stainless steel explosion-bonded joints has been done. This report contains five parts: an ultrasonic examination of explosion-bonded joints and a standard setup; mechanical-property and thermal-cycle tests of GlidCop AL-15/304 stainless steel explosion-bonded joints; leak tests of a GlidCop AL-15/304 stainless steel explosion-bonded interfaces for UHV application; metallurgical examination of explosion-bonded interfaces and failure analysis, and discussion and conclusion

Trivializing violence

DEFF Research Database (Denmark)

Henriksen, Ann-Karina Eske; Bengtsson, Tea Torbenfeldt

2018-01-01

This article analyzes narratives of violence based on interviews with 43 marginalized young Danish people. Their narratives reveal that violence is not only experienced as singular, dramatic encounters; violence is also trivialized in their everyday lives. By drawing on anthropological perspectives...... on everyday violence, we propose a sensitizing framework that enables the exploration of trivialized violence. This framework integrates three perspectives on the process of trivialization: the accumulation of violence; the embodiment of violence; and the temporal and spatial entanglement of violence....... This analysis shows how multiple experiences of violence—as victim, witness, or perpetrator—intersect and mutually inform each other, thereby shaping the everyday lives and dispositions of the marginalized youth. The concept of trivialized violence is a theoretical contribution to cultural and narrative...

Understanding vented gas explosions

Energy Technology Data Exchange (ETDEWEB)

Lautkaski, R. [VTT Energy, Espoo (Finland). Energy Systems

1997-12-31

The report is an introduction to vented gas explosions for nonspecialists, particularly designers of plants for flammable gases and liquids. The phenomena leading to pressure generation in vented gas explosions in empty and congested rooms are reviewed. The four peak model of vented gas explosions is presented with simple methods to predict the values of the individual peaks. Experimental data on the external explosion of dust and gas explosions is discussed. The empirical equation relating the internal and external peak pressures in vented dust explosions is shown to be valid for gas explosion tests in 30 m{sup 3} and 550 m{sup 3} chambers. However, the difficulty of predicting the internal peak pressure in large chambers remains. Methods of explosion relief panel design and principles of vent and equipment layout to reduce explosion overpressures are reviewed. (orig.) 65 refs.

Understanding vented gas explosions

Energy Technology Data Exchange (ETDEWEB)

Lautkaski, R [VTT Energy, Espoo (Finland). Energy Systems

1998-12-31

The report is an introduction to vented gas explosions for nonspecialists, particularly designers of plants for flammable gases and liquids. The phenomena leading to pressure generation in vented gas explosions in empty and congested rooms are reviewed. The four peak model of vented gas explosions is presented with simple methods to predict the values of the individual peaks. Experimental data on the external explosion of dust and gas explosions is discussed. The empirical equation relating the internal and external peak pressures in vented dust explosions is shown to be valid for gas explosion tests in 30 m{sup 3} and 550 m{sup 3} chambers. However, the difficulty of predicting the internal peak pressure in large chambers remains. Methods of explosion relief panel design and principles of vent and equipment layout to reduce explosion overpressures are reviewed. (orig.) 65 refs.

Explosive material treatment in particular the explosive compaction of powders

International Nuclear Information System (INIS)

Pruemmer, R.

1985-01-01

The constructive use of explosives in the last decades has led to new procedures in manufacturing techniques. The most important of these are explosive forming and cladding, the latter especially for the production of compound materials. The method of explosive compaction has the highest potential for further innovation. Almost theoretical densities are achievable in the green compacts as the pressure released by detonating explosives are very high. Also, the production of new conditions of materials (metastable high pressure phases) is possible. (orig.) [de

A cycle of violence? Examining family-of-origin violence, attitudes, and intimate partner violence perpetration.

Science.gov (United States)

Eriksson, Li; Mazerolle, Paul

2015-03-01

Exposure to violence in the family-of-origin has consistently been linked to intimate partner violence (IPV) perpetration in adulthood. However, whether the transmission of violence across generations is role- and gender-specific still remains unclear. The current study examined the effects of experiencing child abuse and observing parental violence on IPV perpetration among a sample of male arrestees (N = 303). The differential effects of observing violence perpetrated by same-sex (father to mother), opposite-sex (mother to father), and both parents on subsequent IPV perpetration were examined. Logistic regression analyses showed that while observing father-only violence and bidirectional interparental violence was predictive of IPV perpetration, observing mother-only violence and direct experiences of child abuse was not. These findings suggest that the transmission of violence across generations is both role- and gender-specific and highlight the importance of examining unique dimensions of partner violence to assess influences on children. The study further examined whether attitudes justifying wife beating mediate the effect of exposure to violence and subsequent IPV perpetration. Results showed that although attitudes were predictive of perpetration, these attitudes did not mediate the relationship. © The Author(s) 2014.

Sorbent Film-Coated Passive Samplers for Explosives Vapour Detection Part A: Materials Optimisation and Integration with Analytical Technologies.

Science.gov (United States)

McEneff, Gillian L; Murphy, Bronagh; Webb, Tony; Wood, Dan; Irlam, Rachel; Mills, Jim; Green, David; Barron, Leon P

2018-04-11

A new thin-film passive sampler is presented as a low resource dependent and discrete continuous monitoring solution for explosives-related vapours. Using 15 mid-high vapour pressure explosives-related compounds as probes, combinations of four thermally stable substrates and six film-based sorbents were evaluated. Meta-aramid and phenylene oxide-based materials showed the best recoveries from small voids (~70%). Analysis was performed using liquid chromatography-high resolution accurate mass spectrometry which also enabled tentative identification of new targets from the acquired data. Preliminary uptake kinetics experiments revealed plateau concentrations on the device were reached between 3-5 days. Compounds used in improvised explosive devices, such as triacetone triperoxide, were detected within 1 hour and were stably retained by the sampler for up to 7 days. Sampler performance was consistent for 22 months after manufacture. Lastly, its direct integration with currently in-service explosives screening equipment including ion mobility spectrometry and thermal desorption mass spectrometry is presented. Following exposure to several open environments and targeted interferences, sampler performance was subsequently assessed and potential interferences identified. High-security building and area monitoring for concealed explosives using such cost-effective and discrete passive samplers can add extra assurance to search routines while minimising any additional burden on personnel or everyday site operation.

Investigation of the decomposition reaction and dust explosion characteristics of crystalline benzoyl peroxides

International Nuclear Information System (INIS)

Lu, K.-T.; Chen, T.-C.; Hu, K.-H.

2009-01-01

The benzoyl peroxide (BPO) is widely used in the chemical industry. Many catastrophes have been caused by its thermal instability or reactive incompatibility in storage or thermal decomposition reaction. Thus, its hazard characteristics have to be clearly identified. First of all, the differential scanning calorimeter (DSC) is used to measure the heat of decomposition reaction, which can contribute to understanding the reaction characteristics of benzoyl peroxide. The accelerating rate calorimeter (ARC) is used to measure the rates of temperature and pressure rises of decomposition reaction, and then the kinetics parameters are estimated. Furthermore, the MIKE 3 apparatus and the 20-l-Apparatus are used to measure and analyze the dust explosion characteristics of benzoyl peroxide under room temperature and atmospheric pressure. Finally, Semenov's thermal explosion theory is applied to investigate the critical runaway condition and the stability criterion of decomposition reaction, and to build the relationship of critical temperature, convective heat transfer coefficient, heat transfer surface area and ambient temperature. These results contribute to improving the safety in the reaction, transportation and storage processes of benzoyl peroxide

Simulation of changes in temperature and pressure fields during high speed projectiles forming by explosion

Directory of Open Access Journals (Sweden)

Marković Miloš D.

2016-01-01

Full Text Available The Research in this paper considered the temperatures fields as the consequently influenced effects appeared by plastic deformation, in the explosively forming process aimed to design Explosively Formed Projectiles (henceforth EFP. As the special payloads of the missiles, used projectiles are packaged as the metal liners, joined with explosive charges, to design explosive propulsion effect. Their final form and velocity during shaping depend on distributed temperatures in explosively driven plastic deformation process. Developed simulation model consider forming process without metal cover of explosive charge, in aim to discover liner’s dynamical correlations of effective plastic strains and temperatures in the unconstrained detonation environment made by payload construction. The temperature fields of the liner’s copper material are considered in time, as the consequence of strain/stress displacements driven by explosion environmental thermodynamically fields of pressures and temperatures. Achieved final velocities and mass loses as the expected EFP performances are estimated regarding their dynamical shaping and thermal gradients behavior vs. effective plastic strains. Performances and parameters are presented vs. process time, numerically simulated by the Autodyne software package. [Projekat Ministarstva nauke Republike Srbije, br. III-47029

Domestic violence and violence against children in Ghana 2015

OpenAIRE

Mueller, Catherine; Tranchant, Jean-Pierre; Oosterhoff, Pauline

2016-01-01

This paper investigates how domestic violence relates to violence against children, including severe corporal punishment. The literature suggests a link between intimate partner violence in the household and child abuse and maltreatment. Studies are, however, limited by the use of narrowly defined measures of violence against children, data availability, and a lack of characterization of domestic violence. In this paper we use original data on domestic violence and child disciplining methods ...

Apparatus and method for detecting explosives

International Nuclear Information System (INIS)

Griffith, B.

1976-01-01

An apparatus is described for use in situations such as airports to detect explosives hidden in containers (for eg. suitcases). The method involves the evaluation of the quantities of oxygen and nitrogen within the container by neutron activation analysis and the determination of whether these quantities exceed predetermined limits. The equipment includes a small sub-critical lower powered reactor for thermal (0.01 to 0.10 eV) neutron production, a radium beryllium primary source, a deuterium-tritium reactor as a high energy (> 1.06 MeV) neutron source and Geiger counter detector arrays. (UK)

Explosive coalescence of magnetic islands and explosive particle acceleration

International Nuclear Information System (INIS)

Tajima, T.; Sakai, J.I.

1985-07-01

An explosive reconnection process associated with the nonlinear evolution of the coalescence instability is found through studies of the electromagnetic particle simulation and the magnetohydrodynamic particle simulation. The explosive coalescence is a process of magnetic collapse, in which we find the magnetic and electrostatic field energies and temperatures (ion temperature in the coalescing direction, in particular) explode toward the explosion time t 0 as (t 0 - t)/sup -8/3/, (t 0 - t) -4 , and (t 0 - t)/sup -8/3/, respectively for a canonical case. Single-peak, double-peak, and triple-peak structures of magnetic energy, temperature, and electrostatic energy, respectively, are observed on the simulation as overshoot amplitude oscillations and are theoretically explained. The heuristic model of Brunel and Tajima is extended to this explosive coalescence in order to extract the basic process. Since the explosive coalescence exhibits self-similarity, a temporal universality, we theoretically search for a self-similar solution to the two-fluid plasma equations

75 FR 1085 - Commerce in Explosives; List of Explosive Materials (2009R-18T)

Science.gov (United States)

2010-01-08

... sensitive slurry and water gel explosives. Blasting caps. Blasting gelatin. Blasting powder. BTNEC [bis.... Explosive conitrates. Explosive gelatins. Explosive liquids. Explosive mixtures containing oxygen-releasing... powder. Fulminate of mercury. Fulminate of silver. Fulminating gold. Fulminating mercury. Fulminating...

75 FR 70291 - Commerce in Explosives; List of Explosive Materials (2010R-27T)

Science.gov (United States)

2010-11-17

..., including non-cap sensitive slurry and water gel explosives. Blasting caps. Blasting gelatin. Blasting.... Explosive conitrates. Explosive gelatins. Explosive liquids. Explosive mixtures containing oxygen-releasing... powder. Fulminate of mercury. Fulminate of silver. Fulminating gold. Fulminating mercury. Fulminating...

Experimental study of the thermal interaction for molten tin dropped into water

International Nuclear Information System (INIS)

Arakeri, V.H.; Catton, I.; Kastenberg, W.E.; Plesset, M.S.

1975-12-01

Multiflash photography with extremely short exposure duration times has been used to observe the interaction of molten tin dropped into a water bath. Detailed photographic evidence is presented which demonstrates that transition, or nucleate boiling, is a possible triggering mechanism for vapor explosions and fragmentation. It was also found that the thermal constraints required to produce vapor explosions could be relaxed by introducing a stable thermal stratification within the coolant. It is shown that the constraints can be relaxed sufficiently to cause vapor explosions for test conditions for which the calculated interface contact temperatures are lower than the homogeneous nucleation temperature of water. This latter finding shows that achievement of limiting coolant superheats associated with spontaneous nucleation is not the only mechanism by which vapor explosions in liquid-liquid systems are possible

Domestic violence

Science.gov (United States)

... violence; Spousal abuse; Elder abuse; Child abuse; Sexual abuse - domestic violence ... 2016. National Domestic Violence Hotline website. What is domestic violence? www.thehotline.org/is-this-abuse/abuse-defined . Accessed July 10, 2016.

Properties and Behavior of Geopolymer Concrete Subjected to Explosive Air Blast Loading: A Review

Directory of Open Access Journals (Sweden)

Mohd Mortar Nurul Aida

2017-01-01

Full Text Available The severe damage to civilian buildings, public area, jet aircraft impact and defense target under explosive blast loading can cause a huge property loss. Most of researcher discusses the topics on design the concrete material model to sustain againts the explosive detonation. The implementation of modern reinforcement steels and fibres in ordinary Portland cement (OPC concrete matrix can reduce the extreme loading effects. However, most researchers have proved that geopolymer concrete (GPC has better mechanical properties towards high performance concrete, compared to OPC. GPC has the high early compressive strength and high ability to resist the thermal energy from explosive detonation. In addition, OPC production is less environmental friendly than geopolymer cement. Geopolymer used can lead to environmental protection besides being improved in mechanical properties. Thus, this paper highlighted on an experimental, numerical and the analytical studies cause of the explosive detonation impact to concrete structures.

A Literature Review of Shock Sensitivity Changes of TATB Due to Thermal Cycling

Energy Technology Data Exchange (ETDEWEB)

Ritter, Boyd [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); New Mexico Inst. of Mining and Technology, Socorro, NM (United States). Dept. of Mechanical Engineering

2016-07-15

Insensitive high explosives (IHEs) based on 1,3,5-triamino 2,4,6-trinitro-benzene (TATB) are the IHEs of choice for use in nuclear warheads over conventional high explosives when safety is the only consideration, because they are very insensitive to thermal or mechanical initiation stimuli. It is this inherent insensitivity to high temperatures, shock, and impact, which provides detonation design challenges when designing TATB explosive systems while at the same time providing a significant level of protection against accidental initiation. Although classified as IHE, over the past few years the focus on explosive safety has demonstrated that the shock sensitivity of TATB is influenced with respect to temperature. A number of studies have been performed on TATB and TATB formulations, plastic bonded explosives (PBX) 9502, and LX-17-01 (LX-17), which demonstrates the increase in shock sensitivity of the explosive after it has been preheated or thermally cycled over various temperature ranges. Many studies suggest the change in sensitivity is partly due to the decomposition rates of the temperature elevated TATB. Others point to the coefficient of thermal expansion, the crystalline structures of TATB and/or the combination of all factors, which create voids which can become active hot spots. During thermal cycling, TATB is known to undergo an irreversible increase in specific volume called ratchet growth. This increase in specific volume correlates to a decrease in density. This decrease in density and increase in volume, demonstrate the creations of additional void spaces which could serve as potential new initiation hot spots thus, increasing the overall sensitivity of the HE. This literature review evaluates the published works to understand why the shock sensitivity of TATB-based plastic bonded explosives (PBXs) changes with temperature.

Media violence.

Science.gov (United States)

Cantor, J

2000-08-01

Research on the effects of media violence is not well understood by the general public. Despite this fact, there is an overwhelming consensus in the scientific literature about the unhealthy effects of media violence. Meta-analyses show that media-violence viewing consistently is associated with higher levels of antisocial behavior, ranging from the trivial (imitative violence directed against toys) to the serious (criminal violence), with many consequential outcomes in between (acceptance of violence as a solution to problems, increased feelings of hostility, and the apparent delivery of painful stimulation to another person). Desensitization is another well-documented effect of viewing violence, which is observable in reduced arousal and emotional disturbance while witnessing violence, the reduced tendency to intervene in a fight, and less sympathy for the victims of violence. Although there is evidence that youth who are already violent are more likely to seek out violent entertainment, there is strong evidence that the relationship between violence viewing and antisocial behavior is bidirectional. There is growing evidence that media violence also engenders intense fear in children which often lasts days, months, and even years. The media's potential role in solutions to these problems is only beginning to be explored, in investigations examining the uses and effects of movie ratings, television ratings, and the V-chip, and the effects of media literacy programs and public education efforts. Future research should explore important individual differences in responses to media violence and effective ways to intervene in the negative effects.

The importance of fragment size distribution on underwater aluminum ignition

International Nuclear Information System (INIS)

Navarro-Valenti, S.; Georgevich, V.; Taleyarkhan, R.P.; Kim, S.H.

1993-01-01

In the study of postulated severe accidents for uranium-aluminum-fueled research reactors, it is necessary to consider the possibility and consequences of fuel/coolant interactions. In the event of a severe accident, where the fuel melts and comes into contact with the coolant, an explosion of considerable violence may occur due to the very fast heat transfer rates involved in the process; this is referred to as thermal interaction. However, when a chemical reaction between the molten aluminum and water occurs simultaneously, its contribution to the energetics of the explosion will produce a much more damaging explosion, referred to as an ignition-type interaction

Liquid explosives

CERN Document Server

Liu, Jiping

2015-01-01

The book drawing on the author's nearly half a century of energetic materials research experience intends to systematically review the global researches on liquid explosives. The book focuses on the study of the conception, explosion mechanism, properties and preparation of liquid explosives. It provides a combination of theoretical knowledge and practical examples in a reader-friendly style. The book is likely to be interest of university researchers and graduate students in the fields of energetic materials, blasting engineering and mining.

Violence exposure and teen dating violence among African American youth.

Science.gov (United States)

Black, Beverly M; Chido, Lisa M; Preble, Kathleen M; Weisz, Arlene N; Yoon, Jina S; Delaney-Black, Virginia; Kernsmith, Poco; Lewandowski, Linda

2015-07-01

This study examines the relationships between exposure to violence in the community, school, and family with dating violence attitudes and behaviors among 175 urban African American youth. Age, gender, state support and experiences with neglect, school violence, and community violence were the most significant predictors of acceptance of dating violence. Experiences with community violence and age were important predictors of dating violence perpetration and victimization. Findings highlight the importance of planning prevention programs that address variables affecting attitudes and behaviors of high-risk youth who have already been exposed to multiple types of violence. © The Author(s) 2014.

RX-08-HD, a low-viscosity, injection-moldable explosive for filling tortuous paths

Energy Technology Data Exchange (ETDEWEB)

Hoffman, D.M.; Jessop, E.S.; Swansiger, R.W.

1997-10-01

Cast cure, extrusion cast, and paste extrudable explosives have not been designed for transferring through long tortuous paths or into fine three dimensional shapes. To allow the crystalline explosive to flow a lubricating fluid is required. The energetic liquid ethane trinitrate (TMETN) was used as the lubricant to maximize the explosive energy. TMETN is a liquid nitrate ester which requires stabilization with conventional free radical stabilizers such as 2- nitrodiphenylamine, methyl-nitroanaline, or ethyl centrylite. Since these injection moldable explosives are expected to cure in place, a polyesterurethane binder based on polymeric isocyanate of hexamethylene diisocyanate and polycaprolactone polyols is dissolved in TMETN. The solubility of the polymer precursors in TMETN also reduces the energetic liquids sensitivity. The latent cure catalyst Dabco T-131 was used to minimize shrinkage associated with thermal expansion, reduce cost associated with oven cures, to give 4-6 hour potlife and overnight cure to handling strength. The product RX-08-HD is a new, low-viscosity, injection moldable explosive that can be extruded into complex, void-free shapes. Combined with appropriate design and other aspects of weaponization, RX-08-HD has produced outstanding results.

Steam explosion pretreatment of softwood: the effect of the explosive decompression on enzymatic digestibility.

Science.gov (United States)

Pielhop, Thomas; Amgarten, Janick; von Rohr, Philipp Rudolf; Studer, Michael H

2016-01-01

Steam explosion pretreatment has been examined in many studies for enhancing the enzymatic digestibility of lignocellulosic biomass and is currently the most common pretreatment method in commercial biorefineries. The information available about the effect of the explosive decompression on the biochemical conversion is, however, very limited, and no studies prove that the latter is actually enhanced by the explosion. Hence, it is of great value to discern between the effect of the explosion on the one hand and the steaming on the other hand, to identify their particular influences on enzymatic digestibility. The effect of the explosive decompression in the steam explosion pretreatment of spruce wood chips on their enzymatic cellulose digestibility was studied systematically. The explosion had a high influence on digestibility, improving it by up to 90 % compared to a steam pretreatment without explosion. Two factors were identified to be essentially responsible for the effect of the explosion on enzymatic digestibility: pretreatment severity and pressure difference of the explosion. A higher pretreatment severity can soften up and weaken the lignocellulose structure more, so that the explosion can better break up the biomass and decrease its particle size, which enhances its digestibility. In particular, increasing the pressure difference of the explosion leads to more defibration, a smaller particle size and a better digestibility. Though differences were found in the micro- and nanostructure of exploded and non-exploded biomass, the only influence of the explosion on digestibility was found to be the macroscopic particle size reduction. Steam explosion treatments with a high severity and a high pressure difference of the explosion lead to a comparatively high cellulose digestibility of the-typically very recalcitrant-softwood biomass. This is the first study to show that explosion can enhance the enzymatic digestibility of lignocellulosic biomass. If the

Thermal stability of detonation-produced micro and nanodiamonds

Science.gov (United States)

Efremov, V. P.; Zakatilova, E. I.; Maklashova, I. V.; Shevchenko, N. V.

2018-01-01

Detonation nanodiamonds are produced at utilization of high explosives. When an explosive blasts in a water environment, the detonation products contain microdiamonds, and in a gaseous medium, nanodiamonds. It is known that with decreasing size the influence of the surface energy of particles on their properties increases. Thus, it is interesting to compare the properties of detonation nano and microdiamonds. In this study, we have examined the thermal stability of diamond materials by synchronous thermal analysis. The experiments were performed at atmospheric pressure in argon flow for different heating rates in a range from room temperature to 1500 °C. Samples of initial and annealed micro and nanomaterials were studied using electron microscopy, x-ray and x-ray-fluorescence analysis. It was established that thermal and structural properties of micro and nanodiamonds differ substantially.

Improved explosive collection and detection with rationally assembled surface sampling materials

Energy Technology Data Exchange (ETDEWEB)

Chouyyok, Wilaiwan; Bays, J. Timothy; Gerasimenko, Aleksandr A.; Cinson, Anthony D.; Ewing, Robert G.; Atkinson, David A.; Addleman, R. Shane

2016-01-01

Sampling and detection of trace explosives is a key analytical process in modern transportation safety. In this work we have explored some of the fundamental analytical processes for collection and detection of trace level explosive on surfaces with the most widely utilized system, thermal desorption IMS. The performance of the standard muslin swipe material was compared with chemically modified fiberglass cloth. The fiberglass surface was modified to include phenyl functional groups. When compared to standard muslin, the phenyl functionalized fiberglass sampling material showed better analyte release from the sampling material as well as improved response and repeatability from multiple uses of the same swipe. The improved sample release of the functionalized fiberglass swipes resulted in a significant increase in sensitivity. Various physical and chemical properties were systematically explored to determine optimal performance. The results herein have relevance to improving the detection of other explosive compounds and potentially to a wide range of other chemical sampling and field detection challenges.

A comparative study on two explosive acetone peroxides

Energy Technology Data Exchange (ETDEWEB)

Egorshev, V. Yu.; Sinditskii, V.P., E-mail: vps@rctu.ru; Smirnov, S.P.

2013-12-20

Highlights: • The most accurate heats of DADP and TATP sublimation were evaluated from experimental vapor pressures in a widened temperature range. • DADP is more volatile while more thermally stable peroxide than TATP. • DADP reveals lesser sensitivity to drop-weight impact, flame temperature, burning rate, and initiating efficiency as compared with TATP. - Abstract: Two explosive cyclic acetone peroxides, diacetone diperoxide (DADP) and triacetone triperoxide (TATP) have been studied in respect of thermal decomposition, burning behavior, impact sensitivity, and initiating efficiency. Using the glass Bourdon gauge technique, the vapor pressures of TATP and DADP were determined over the temperature range 75–144 °C and 67–120 °C, respectively. The kinetic parameters of decomposition of the peroxides in the gas phase have been obtained in the temperature interval of 140–200 °C. The decomposition of both DADP and TATP followed the first-order reaction to high degrees of decay with close activation energies of 159.2 kJ/mol (38.0 kcal/mol) and 165.8 kJ/mol (39.6 kcal/mol), respectively. The decomposition rate constants of DADP were found to be approximately 2 times less than those of TATP. The linear burning rate of DADP measured in a constant-pressure window bomb appeared to be approximately 5 times less than that of TATP. Temperature profiles in the combustion wave were measured at subatmospheric pressures with the help of thin tungsten-rhenium thermocouples. The leading reaction on combustion of both volatile peroxides was assumed to occur in the gas phase. Kinetic parameters of the leading reaction derived from the combustion data showed a good agreement with kinetic parameters of low-temperature thermal decomposition extrapolated to the high-temperature flame zone. In the drop-weight impact test, DADP appeared to be notably less sensitive peroxide than TATP. No deflagration-to-detonation transition was observed when RDX was attempted to explode by

Studies of the laser-induced fluorescence of explosives and explosive compositions.

Energy Technology Data Exchange (ETDEWEB)

Hargis, Philip Joseph, Jr. (,; .); Thorne, Lawrence R.; Phifer, Carol Celeste; Parmeter, John Ethan; Schmitt, Randal L.

2006-10-01

Continuing use of explosives by terrorists throughout the world has led to great interest in explosives detection technology, especially in technologies that have potential for standoff detection. This LDRD was undertaken in order to investigate the possible detection of explosive particulates at safe standoff distances in an attempt to identify vehicles that might contain large vehicle bombs (LVBs). The explosives investigated have included the common homogeneous or molecular explosives, 2,4,6-trinitrotoluene (TNT), pentaerythritol tetranitrate (PETN), cyclonite or hexogen (RDX), octogen (HMX), and the heterogeneous explosive, ammonium nitrate/fuel oil (ANFO), and its components. We have investigated standard excited/dispersed fluorescence, laser-excited prompt and delayed dispersed fluorescence using excitation wavelengths of 266 and 355 nm, the effects of polarization of the laser excitation light, and fluorescence imaging microscopy using 365- and 470-nm excitation. The four nitro-based, homogeneous explosives (TNT, PETN, RDX, and HMX) exhibit virtually no native fluorescence, but do exhibit quenching effects of varying magnitude when adsorbed on fluorescing surfaces. Ammonium nitrate and fuel oil mixtures fluoresce primarily due to the fuel oil, and, in some cases, due to the presence of hydrophobic coatings on ammonium nitrate prill or impurities in the ammonium nitrate itself. Pure ammonium nitrate shows no detectable fluorescence. These results are of scientific interest, but they provide little hope for the use of UV-excited fluorescence as a technique to perform safe standoff detection of adsorbed explosive particulates under real-world conditions with a useful degree of reliability.

Gender's Role in Exposure to Interparental Violence, Acceptance of Violence, Self-Efficacy, and Physical Teen Dating Violence Among Quebec Adolescents.

Science.gov (United States)

Ruel, Catherine; Lavoie, Francine; Hébert, Martine; Blais, Martin

2017-05-01

Despite efforts to prevent physical teen dating violence, it remains a major public health issue with multiple negative consequences. This study aims to investigate gender differences in the relationships between exposure to interparental violence (mother-to-father violence, father-to-mother violence), acceptance of dating violence (perpetrated by boys, perpetrated by girls), and self-efficacy to disclose teen dating violence. Data were drawn from Waves 1 and 2 of the Quebec Youth Romantic Relationships Project, conducted with a representative sample of Quebec high school students. Analyses were conducted on a subsample of 2,564 teenagers who had been in a dating relationship in the past 6 months (63.8% girls, mean age of 15.3 years). Path analyses were conducted to investigate the links among exposure to interparental violence, acceptance of violence, self-efficacy to disclose teen dating violence (measured at Wave 1), and physical teen dating violence (measured at Wave 2). General exposure to interparental violence was linked, through acceptance of girl-perpetrated violence, to victimization among both genders and to girls' perpetration of physical teen dating violence. No significant difference was identified in the impact of the gender of the perpetrating parent when considering exposure to interparental violence. Self-efficacy to disclose personal experiences of violence was not linked to exposure to interparental violence or to experiences of physical teen dating violence. The findings support the intergenerational transmission of violence. Moreover, the findings underline the importance of targeting acceptance of violence, especially girl-perpetrated violence, in prevention programs and of intervening with children and adolescents who have witnessed interparental violence.

Experimental simulation of microinteractions in large scale explosions

Energy Technology Data Exchange (ETDEWEB)

Chen, X.; Luo, R.; Yuen, W.W.; Theofanous, T.G. [California Univ., Santa Barbara, CA (United States). Center for Risk Studies and Safety

1998-01-01

This paper presents data and analysis of recent experiments conducted in the SIGMA-2000 facility to simulate microinteractions in large scale explosions. Specifically, the fragmentation behavior of a high temperature molten steel drop under high pressure (beyond critical) conditions are investigated. The current data demonstrate, for the first time, the effect of high pressure in suppressing the thermal effect of fragmentation under supercritical conditions. The results support the microinteractions idea, and the ESPROSE.m prediction of fragmentation rate. (author)

76 FR 64974 - Commerce in Explosives; List of Explosive Materials (2011R-18T)

Science.gov (United States)

2011-10-19

... slurry and water gel explosives. Blasting caps. Blasting gelatin. Blasting powder. BTNEC [bis.... Esters of nitro-substituted alcohols. Ethyl-tetryl. Explosive conitrates. Explosive gelatins. Explosive... silver. Fulminating gold. Fulminating mercury. Fulminating platinum. Fulminating silver. G Gelatinized...

The reactants equation of state for the tri-amino-tri-nitro-benzene (TATB) based explosive PBX 9502

Science.gov (United States)

Aslam, Tariq D.

2017-07-01

The response of high explosives (HEs), due to mechanical and/or thermal insults, is of great importance for both safety and performance. A major component of how an HE responds to these stimuli stems from its reactant equation of state (EOS). Here, the tri-amino-tri-nitro-benzene based explosive PBX 9502 is investigated by examining recent experiments. Furthermore, a complete thermal EOS is calibrated based on the functional form devised by Wescott, Stewart, and Davis [J. Appl. Phys. 98, 053514 (2005)]. It is found, by comparing to earlier calibrations, that a variety of thermodynamic data are needed to sufficiently constrain the EOS response over a wide range of thermodynamic state space. Included in the calibration presented here is the specific heat as a function of temperature, isobaric thermal expansion, and shock Hugoniot response. As validation of the resulting model, isothermal compression and isentropic compression are compared with recent experiments.

A single sphere film boiling model for trigger ability and explosion potential

International Nuclear Information System (INIS)

Park, Ik Kyu; Kim, Jong Hwan; Hong, Seong Ho; Hong, Seong Wan

2012-01-01

The main causes for the controversy about the corium explosiveness are the hydrogen effect, large voided mixture, material property, poor triggering event (wrong position, weak triggering, wrong time), and low superheat due to a high melting temperature. It has been suggested that a steam explosion of the corium/water system must be suppressed due to the physical properties of corium such as high temperature, high density, multicomponent oxide melt, and low thermal conductivity. It was also claimed that the magnitude of the effect on the FCI results of corium/water systems is on the order of higher density, higher temperature, and non eutectic composition. This concept of a material effect is supported to some degree by parametric experimental results. However, the parametric results between the steam explosion pressure and the material compositions do not directly provide an understanding of the mechanism for the material difference affecting a steam explosion process, even though the sensitivity results can reveal the trends of some parameters affecting the FCI results. This concept of a material effect is supported to some degree by parametric experimental results. The parametric tests themselves also provide us with information on the effect of each initial parameter on a steam explosion. However, sensitivity studies between the steam explosion pressure and the initial value of a parameter do not directly provide an understanding of the steam explosion process. Handling the explosion res sure and initial condition without a mixing could not contribute to a code development process. We need a certain parameter for representing mixing, but we cannot measure it during the FCI tests. The particle size distribution collected after the FCI tests can be a good indicator for explaining a mixing process. In this paper, TROI tests were analyzed in view of a particle size response for various types of fuel coolant explosions. The heat losses and remnants were calculated

77 FR 58410 - Commerce in Explosives; List of Explosive Materials (2012R-10T)

Science.gov (United States)

2012-09-20

... sensitive slurry and water gel explosives. Blasting caps. Blasting gelatin. Blasting powder. BTNEC [bis.... Esters of nitro-substituted alcohols. Ethyl-tetryl. Explosive conitrates. Explosive gelatins. Explosive.... Fulminate of silver. Fulminating gold. Fulminating mercury. Fulminating platinum. Fulminating silver. G...

The relationship between severity of violence in the home and dating violence.

Science.gov (United States)

Sims, Eva Nowakowski; Dodd, Virginia J Noland; Tejeda, Manuel J

2008-01-01

This study used propositions from the social learning theory to explore the effects of the combined influences of child maltreatment, childhood witness to parental violence, sibling violence, and gender on dating violence perpetration using a modified version of the Conflict Tactics Scale 2 (CTS2). A weighted scoring method was utilized to determine how severity of violence in the home impacts dating violence perpetration. Bivariate correlations and linear regression models indicate significant associations between child maltreatment, sibling violence perpetration, childhood witness to parental violence, gender, and subsequent dating violence perpetration. Multiple regression analyses indicate that for men, history of severe violence victimization (i.e., child maltreatment and childhood witness to parental violence) and severe perpetration (sibling violence) significantly predict dating violence perpetration.

Influence of the magnetic field in the time evolution of the solar explosion radiation in X-ray and microwaves

International Nuclear Information System (INIS)

Costa, J.E.R.

1983-01-01

It has been made a theoretical development, sel-consistent with recent models for the explosive source, applied to time delays of peak emission at different microwave frequencies, and between microwaves and hard X-ray emission. A working hipothesis has been assumed with the adoption of a growing magnetic field during the solar flare explosion, and therefore contributing to a growth in microwave emission, differential in frequency, producing delays of maximum emission towards lower microwave frequencies, and delays of microwave maximum emission with respect to hard X-rays. It has been found that these delays are consistent with a growth in the magnetic field of about 14% by assuming both thermal and non-thermal models. This variation in magnetic field has been associated to movements of thermal sources downwards in the solar atmosphere, and it has been found that the estimated velocities of displacement were consistent compared to characteristic velocities of anomalous conduction fronts of thermal models. (Author) [pt

Violence in the Street, Violence of the Street

DEFF Research Database (Denmark)

Heinskou, Marie Bruvik; Liebst, Lasse Suonperä

While in his early and general theory of interaction rituals Randall Collins emphasised that social situations are both ’symbolic’ and ’material’, the latter dimension is largely absent from Collins’ theory of violence(Collins 2004; 1993: 214). Compared with criminology’s more recent situational...... studies of violence, it is noticeable that the analytical success of these studies is closely linked with understanding street violence as a spatial-situational phenomenon (Clarke 1997; Eck & Weisburd 1995; Bragand & Weisburd; 2010; Wikström et al. 2012; Sampson et al. 1997). In light of evidence...... for the spatial concentration of street violence, this paper takes its point of departure in a large study of Street Violence among youth in Copenhagen, Denmark (combining quantitative data from filed police reports (N = 501), data from CCTV (N=100) and qualitative analysis of selected cases of street violence...

Underground nuclear explosions

International Nuclear Information System (INIS)

Higgins, Gary H.

1970-01-01

In the Third Plowshare Symposium, held in 1964, data from a number of nuclear explosions were presented. At that time the basic elements of the nuclear explosion appeared to be well understood and relationships for predicting the gross nuclear effects were presented. Since that time, additional work has been done and many of the concepts have been extended. For example, nuclear explosions have been conducted at greater depths and with much greater yields. The physical and chemical properties of the material in which the explosions occur have been more accurately measured and related to explosion effects. Interpretation of the new information seems to indicate that the earlier relationships are valid over the ranges of energy and depths for which data is available but that effects relating to cavity and chimney sizes or fracturing had been overestimated at great depths of burst and higher yields. (author)

Underground nuclear explosions

Energy Technology Data Exchange (ETDEWEB)

Higgins, Gary H [Lawrence Radiation Laboratory, University of California, Livermore, CA (United States)

1970-05-01

In the Third Plowshare Symposium, held in 1964, data from a number of nuclear explosions were presented. At that time the basic elements of the nuclear explosion appeared to be well understood and relationships for predicting the gross nuclear effects were presented. Since that time, additional work has been done and many of the concepts have been extended. For example, nuclear explosions have been conducted at greater depths and with much greater yields. The physical and chemical properties of the material in which the explosions occur have been more accurately measured and related to explosion effects. Interpretation of the new information seems to indicate that the earlier relationships are valid over the ranges of energy and depths for which data is available but that effects relating to cavity and chimney sizes or fracturing had been overestimated at great depths of burst and higher yields. (author)

Theoretical investigations on the fragmentation of drops of melt with respect to the description of thermal detonations (vapor explosions) and their application in the code Frademo

International Nuclear Information System (INIS)

Burger, M.; Carachalios, C.; Kim, D.S.; Unger, H.

1986-01-01

Vapor explosions caused by the contact of molten core material with coolant are an important issue within reactor safety analysis, because they could produce an early threat to the containment during a core melt accident. The case of steady-state propagation of a detonation wave through a coarse premixture of melt and coolant represents the most severe case of a large scale vapor explosion under reactor conditions with the highest rate and largest heat release and therefore also the highest yield of mechanical energy. The present contribution starts with the description of the integral model of the detonation wave. The fragmentation processes, which are decisive for these exchange terms and the detonation process as a whole, are dealt with also. Hydrodynamic fragmentation processes as well as a thermally induced one are considered. The processes which take place inside a detonation wave, especially the fragmentation of the drops of melt and the velocity equilibration between the melt and the coolant, determine the behavior of the wave. In the present model these processes are described within a three-phase approach, considering the drops of melt, the fragments and the coolant as separate flow phases. In the frame of this work, the computer code FRADEMO has been developed. It consists of an overall description of the processes inside a steady-state detonation wave in combination with a full description of the detailed models on hydrodynamic and thermal fragmentation presented in this report. Some useful information for the potential code user is given in the appendix of the detailed report also

Previous experience of family violence and intimate partner violence in pregnancy.

Science.gov (United States)

Ludermir, Ana Bernarda; Araújo, Thália Velho Barreto de; Valongueiro, Sandra Alves; Muniz, Maria Luísa Corrêa; Silva, Elisabete Pereira

2017-01-01

To estimate differential associations between the exposure to violence in the family of origin and victimization and perpetration of intimate partner violence in pregnancy. A nested case-control study was carried out within a cohort study with 1,120 pregnant women aged 18-49 years old, who were registered in the Family Health Strategy of the city of Recife, State of Pernambuco, Brazil, between 2005 and 2006. The cases were the 233 women who reported intimate partner violence in pregnancy and the controls were the 499 women who did not report it. Partner violence in pregnancy and previous experiences of violence committed by parents or other family members were assessed with a standardized questionnaire. Multivariate logistic regression analyses were modeled to identify differential associations between the exposure to violence in the family of origin and victimization and perpetration of intimate partner violence in pregnancy. Having seen the mother suffer intimate partner violence was associated with physical violence in childhood (OR = 2.62; 95%CI 1.89-3.63) and in adolescence (OR = 1.47; 95%CI 1.01-2.13), sexual violence in childhood (OR = 3.28; 95%CI 1.68-6.38) and intimate partner violence during pregnancy (OR = 1.47; 95% CI 1.01 - 2.12). The intimate partner violence during pregnancy was frequent in women who reported more episodes of physical violence in childhood (OR = 2.08; 95%CI 1.43-3.02) and adolescence (OR = 1.63; 95%CI 1.07-2.47), who suffered sexual violence in childhood (OR = 3.92; 95%CI 1.86-8.27), and who perpetrated violence against the partner (OR = 8.67; 95%CI 4.57-16.45). Experiences of violence committed by parents or other family members emerge as strong risk factors for intimate partner violence in pregnancy. Identifying and understanding protective and risk factors for the emergence of intimate partner violence in pregnancy and its maintenance may help policymakers and health service managers to develop intervention strategies.

Stellar explosion

International Nuclear Information System (INIS)

Suraud, E.

1987-01-01

What is the energy source and which physical processes are powerful enough to generate this explosion which scatters the star. The knowledge progress of very dense matter allows the scenario reconstitution. An instability in the star core which is developing during milliseconds is the cause of this explosion [fr

Steam explosion studies review

International Nuclear Information System (INIS)

Hwang, Moon Kyu; Kim, Hee Dong

1999-03-01

When a cold liquid is brought into contact with a molten material with a temperature significantly higher than the liquid boiling point, an explosive interaction due to sudden fragmentation of the melt and rapid evaporation of the liquid may take place. This phenomenon is referred to as a steam explosion or vapor explosion. Depending upon the amount of the melt and the liquid involved, the mechanical energy released during a vapor explosion can be large enough to cause serious destruction. In hypothetical severe accidents which involve fuel melt down, subsequent interactions between the molten fuel and coolant may cause steam explosion. This process has been studied by many investigators in an effort to assess the likelihood of containment failure which leads to large scale release of radioactive materials to the environment. In an effort to understand the phenomenology of steam explosion, extensive studies has been performed so far. The report presents both experimental and analytical studies on steam explosion. As for the experimental studies, both small scale tests which involve usually less than 20 g of high temperature melt and medium/large scale tests which more than 1 kg of melt is used are reviewed. For the modelling part of steam explosions, mechanistic modelling as well as thermodynamic modelling is reviewed. (author)

Atmospheric emission of NOx from mining explosives: A critical review

Science.gov (United States)

Oluwoye, Ibukun; Dlugogorski, Bogdan Z.; Gore, Jeff; Oskierski, Hans C.; Altarawneh, Mohammednoor

2017-10-01

High-energy materials such as emulsions, slurries and ammonium-nitrate fuel-oil (ANFO) explosives play crucial roles in mining, quarrying, tunnelling and many other infrastructure activities, because of their excellent transport and blasting properties. These explosives engender environmental concerns, due to atmospheric pollution caused by emission of dust and nitrogen oxides (NOx) from blasts, the latter characterised by the average emission factor of 5 kg (t AN explosive)-1. This first-of-its-kind review provides a concise literature account of the formation of NOx during blasting of AN-based explosives, employed in surface operations. We estimate the total NOx emission rate from AN-based explosives as 0.05 Tg (i.e., 5 × 104 t) N per annum, compared to the total global annual anthropogenic NOx emissions of 41.3 × 106 t N y-1. Although minor in the global sense, the large localised plumes from blasting exhibit high NOx concentration (500 ppm) exceeding up to 3000 times the international standards. This emission has profound consequences at mining sites and for adjacent atmospheric environment, necessitating expensive management of exclusion zones. The review describes different types of AN energetic materials for civilian applications, and summarises the essential properties and terminologies pertaining to their use. Furthermore, we recapitulate the mechanisms that lead to the formation of the reactive nitrogen species in blasting of AN-based explosives, review their implications to atmospheric air pollution, and compare the mechanisms with those experienced in other thermal and combustion operations. We also examine the mitigation approaches, including guidelines and operational-control measures. The review discusses the abatement technologies such as the formulation of new explosive mixtures, comprising secondary fuels, spin traps and other additives, in light of their effectiveness and efficiency. We conclude the review with a summary of unresolved problems

Coating and Characterization of Mock and Explosive Materials

Directory of Open Access Journals (Sweden)

Emily M. Hunt

2012-01-01

Full Text Available This project develops a method of manufacturing plastic-bonded explosives by using use precision control of agglomeration and coating of energetic powders. The energetic material coating process entails suspending either wet or dry energetic powders in a stream of inert gas and contacting the energetic powder with atomized droplets of a lacquer composed of binder and organic solvent. By using a high-velocity air stream to pneumatically convey the energetic powders and droplets of lacquer, the energetic powders are efficiently wetted while agglomerate drying begins almost immediately. The result is an energetic powder uniformly coated with binder, that is, a PBX, with a high bulk density suitable for pressing. Experiments have been conducted using mock explosive materials to examine coating effectiveness and density. Energetic materials are now being coated and will be tested both mechanically and thermally. This allows for a comprehensive comparison of the morphology and reactivity of the newly coated materials to previously manufactured materials.

Dating Violence

Science.gov (United States)

... for Teens / Dating Violence Bulletins for Teens: Dating Violence What is it? If you are a victim ... often. If You Are a Victim of Dating Violence, You Might… Think it's your fault. Feel angry, ...

Fire and explosion hazards to flora and fauna from explosives.

Science.gov (United States)

Merrifield, R

2000-06-30

Deliberate or accidental initiation of explosives can produce a range of potentially damaging fire and explosion effects. Quantification of the consequences of such effects upon the surroundings, particularly on people and structures, has always been of paramount importance. Information on the effects on flora and fauna, however, is limited, with probably the weakest area lying with fragmentation of buildings and their effects on different small mammals. Information has been used here to gain an appreciation of the likely magnitude of the potential fire and explosion effects on flora and fauna. This is based on a number of broad assumptions and a variety of data sources including World War II bomb damage, experiments performed with animals 30-40 years ago, and more recent field trials on building break-up under explosive loading.

[Family violence].

Science.gov (United States)

Manoudi, F; Chagh, R; Es-soussi, M; Asri, F; Tazi, I

2013-09-01

Family violence is a serious public health problem, the scale of which is seriously increasing in Morocco. Although it has existed for a long time, we ignore the real characteristics of this plague in our country; our work consisted in an epidemiological approach of family violence in Marrakech during 2006. After elaborating a questionnaire, which allows the study of the demographic and social profile of the families, the study of violence exercised in the family and the evaluation of the depression in the women, we led an inquiry amongst 265 women. Analysis of the results obtained has allowed us to underline the following characteristics: 16.6% of the women in our sample had been physically beaten; the young age is a risk factor; the age range most affected by violence is in women between the ages of 30 and 40 and which represent 39% of the battered women; domestic violence touches all the social, economic and cultural classes: in our study, 63% of the women having undergone violence were housewives, 25% were managers and 3% senior executives; family problems were the most important cause of violence in our study, representing 32.32%. Requests for money was the cause in 11.3% of the cases, and imposed sexual relations were found in 6.8% of the cases; alcoholism is an aggravating factor of family violence; 27.3% of the spouses who assaulted their wives were drunk; 52% of the assaulted women were victims of violence in childhood and 36% had been witness to their father's violence; in 63.6% of the cases of violence, the children were witnesses, and in 25% of the cases the children were victims of violence at the same time as their mothers; 50% of the women victims of violence did not react, while 38.6% left home, and 9.1 filed for divorce. Thirty-two percent of the assaulted woman had been traumatised by the aggression; the association of depression and violence was very high, 343% of the battered women in our study suffered from severe depression. This work

Mechanical and chemical responses of low-velocity impacted RDX and HMX explosive powders

Science.gov (United States)

Wu, Yanqing; Guo, Hongfu; Huang, Fenglei; Bao, Xiaowei; Explosion; damage Team

2017-06-01

The experimental analyses of mechanical and chemical responses of RDX and HMX particles were performed based on the optimized drop-weight experimental system equipped with the High-Speed Camera (HSC). It has been found that Jetting phenomenon observed by HSC is the result of the energy released by gaseous products, which push the pulverized or melted explosives to splash radially. Jetting is the only and the most obvious difference between reactive and inert particles prior to combustion so that jetting can be regarded as the sign of ignition. Area expansion velocity, jetting velocity, and flame propagation velocity have been estimated via image processing, making it possible to characterize mechanical deformation and violence of reaction of each stage. Hot-spots coalescence promotes flame propagation whose velocity reflects the violence of deflagration reaction. Jetting appearance time can be used to determine time-to-ignition more accurately than other ways. For RDX, molten phase plays an important role to the formation of the hot-spots. Multiple particles experienced more severe burning reactions than an individual particle. China National Nature Science Foundation (11572045), ``Science Challenging Program'' (JCKY2016212A501),opening fund from Safety ammunition research and Development Center (RMC2015B03).

Domestic Violence

Science.gov (United States)

Domestic violence is a type of abuse. It usually involves a spouse or partner, but it can also ... a child, elderly relative, or other family member. Domestic violence may include Physical violence that can lead to ...

Explosion of a low mass neutron star

International Nuclear Information System (INIS)

Blinnikov, S.I.; Imshennik, V.S.; Nadyozhin, D.K.; Novikov, I.D.; Polnarev, A.G.; AN SSSR, Moscow. Fizicheskij Inst.); Perevodchikova, T.V.

1990-01-01

The hydrodynamical disruption of a low mass neutron star is investigated for the case when the stellar mass becomes smaller than the minimum value, M min ≅0.1 M sun . The final phase of the process is shown to proceed explosively, leading to an expansion of all the star, with a kinetic energy of 4.8 MeV per nucleon. The results of calculations are virtually independent of the way in which the neutron star mass goes down below M min (mass exchange in a close binary stellar system, nucleon decay, or some effective mass loss due to a hypothetical decrease of the gravitational constant). The neutron star disruption is followed by a short (0.01-0.1 s) burst of thermal hard X-rays and soft gamma-rays (kT=10-100 keV) with a subsequent much more prolonged tail of radiation induced by decays of long-lived radioactive nuclides. Some fraction of the explosion energy may be emitted in the form of neutrinos. (orig.)

Similarities and differences in vapor explosion criteria

International Nuclear Information System (INIS)

Cronenberg, A.W.

1978-01-01

An overview of recent ideas pertaining to vapor explosion criteria indicates that in general sense, a consensus of opinion is emerging on the conditions applicable to explosive vaporization. Experimental and theoretical work has lead a number of investigators to the formulation of such conditions which are quite similar in many respects, although the quantitative details of the model formulation of such conditions are somewhat different. All model concepts are consistent in that an initial period of stable film boiling, separating molten fuel from coolant, is considered necessary (at least for large-scale interactions and efficient intermixing), with subsequent breakdown of film boiling due to pressure and/or thermal effects, followed by intimate fuel-coolant contact and a rapid vaporization process which is sufficient to cause shock pressurization. Although differences arise as to the conditions for and the energetics associated with film boiling destabilization and the mode and energetics of fragmentation and intermixing. However, the principal area of difference seems to be the question of what constitutes the requisite condition(s) for rapid vapor production to cause shock pressurization

Optical detection of explosives: spectral signatures for the explosive bouquet

Science.gov (United States)

Osborn, Tabetha; Kaimal, Sindhu; Causey, Jason; Burns, William; Reeve, Scott

2009-05-01

Research with canines suggests that sniffer dogs alert not on the odor from a pure explosive, but rather on a set of far more volatile species present in an explosive as impurities. Following the explosive trained canine example, we have begun examining the vapor signatures for many of these volatile impurities utilizing high resolution spectroscopic techniques in several molecular fingerprint regions. Here we will describe some of these high resolution measurements and discuss strategies for selecting useful spectral signature regions for individual molecular markers of interest.

Sexual Violence Prevention

Science.gov (United States)

... Submit What's this? Submit Button Past Emails Sexual Violence Prevention Recommend on Facebook Tweet Share Compartir April ... stop sexual violence before it begins. Understanding Sexual Violence Sexual violence is any sexual activity where consent ...

Teen Dating Violence

Science.gov (United States)

... Room Social Media Publications Injury Center Teen Dating Violence Recommend on Facebook Tweet Share Compartir On This ... serious forms of violence. What is teen dating violence? Teen Dating Violence [550 KB, 2 Pages, 508] ...

Previous experience of family violence and intimate partner violence in pregnancy

Directory of Open Access Journals (Sweden)

Ana Bernarda Ludermir

2017-09-01

Full Text Available ABSTRACT OBJECTIVE To estimate differential associations between the exposure to violence in the family of origin and victimization and perpetration of intimate partner violence in pregnancy. METHODS A nested case-control study was carried out within a cohort study with 1,120 pregnant women aged 18–49 years old, who were registered in the Family Health Strategy of the city of Recife, State of Pernambuco, Brazil, between 2005 and 2006. The cases were the 233 women who reported intimate partner violence in pregnancy and the controls were the 499 women who did not report it. Partner violence in pregnancy and previous experiences of violence committed by parents or other family members were assessed with a standardized questionnaire. Multivariate logistic regression analyses were modeled to identify differential associations between the exposure to violence in the family of origin and victimization and perpetration of intimate partner violence in pregnancy. RESULTS Having seen the mother suffer intimate partner violence was associated with physical violence in childhood (OR = 2.62; 95%CI 1.89–3.63 and in adolescence (OR = 1.47; 95%CI 1.01–2.13, sexual violence in childhood (OR = 3.28; 95%CI 1.68–6.38 and intimate partner violence during pregnancy (OR = 1.47; 95% CI 1.01 – 2.12. The intimate partner violence during pregnancy was frequent in women who reported more episodes of physical violence in childhood (OR = 2.08; 95%CI 1.43–3.02 and adolescence (OR = 1.63; 95%CI 1.07–2.47, who suffered sexual violence in childhood (OR = 3.92; 95%CI 1.86–8.27, and who perpetrated violence against the partner (OR = 8.67; 95%CI 4.57–16.45. CONCLUSIONS Experiences of violence committed by parents or other family members emerge as strong risk factors for intimate partner violence in pregnancy. Identifying and understanding protective and risk factors for the emergence of intimate partner violence in pregnancy and its maintenance may help

Thermal decomposition of organic solvent with nitric acid in nuclear fuel reprocessing plants

Energy Technology Data Exchange (ETDEWEB)

Koike, Tadao; Nishio, Gunji; Takada, Junichi; Tukamoto, Michio; Watanabe, Kouji [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Miyata, Sadaichirou

1995-02-01

Since a thermal decomposition of organic solvent containing TBP (tributyl phosphate) with nitric acid and heavy metal nitrates is an exothermic reaction, it is possible to cause an explosive decomposition of TBP-complex materials formed by a nitration between the solvent and nitric acid, if the solvent involving TBP-complex is heated upto a thermal limit in an evaporator to concentrate a fuel liquid solution from the extraction process in the reprocessing plant. In JAERI, the demonstration test for explosive decomposition of TBP-complex by the nitration was performed to elucidate the safety margin of the evaporator in the event of hypothetical explosion under auspices of the Science and Technology Agency. The demonstration test was carried out by heating TBP/n-dodecane solvent mixed with nitric acid and uranium nitrate. In the test, the thermal decomposition behavior of the solvent was examined, and also a kinematic reaction constant and a heat formation of the TBP-complex decomposition were measured by the test. In the paper, a safety analysis of a model evaporator was conducted during accidental conditions under the explosive decomposition of the solvent. (author).

Understanding sexual violence as a form of caste violence

Directory of Open Access Journals (Sweden)

Prachi Patil

2016-07-01

Full Text Available The paper attempts to understand narratives of sexual violence anchored within the dynamics of social location of caste and gender. Apparent caste-patriarchy and gender hierarchies which are at play in cases of sexual violence against lower-caste and dalit women speak about differential experiences of rape and sexual abuse that women have in India. The paper endeavours to establish that sexual violence is also a form of caste violence by rereading the unfortunate cases of Bhanwari Devi, Khairlanji, Lalasa Devi and Delta Meghwal Keywords: caste-patriarchy, Dalit women, POA Act, rape, sexual violence

The control and prevention of dust explosions

Energy Technology Data Exchange (ETDEWEB)

1982-01-01

Papers presented discussed: explosion characteristics and hybrid mixtures explosion characteristics and influencing factors, propagation of dust explosions in ducts, prevention of dust explosions, desensitization, explosion-proof type of construction, explosion pressure relief, optical flame barriers, slide-valves for explosion protection, Ventex explosion barrier valves, grinding and mixing plants, spray driers, dust explosions in silos, and explosion-proof bucket elevators. One paper has been abstracted separately.

Thermal-mechanical-chemical responses of polymer-bonded explosives using a mesoscopic reactive model under impact loading.

Science.gov (United States)

Wang, XinJie; Wu, YanQing; Huang, FengLei

2017-01-05

A mesoscopic framework is developed to quantify the thermal-mechanical-chemical responses of polymer-bonded explosive (PBX) samples under impact loading. A mesoscopic reactive model is developed for the cyclotetramethylenetetranitramine (HMX) crystal, which incorporates nonlinear elasticity, crystal plasticity, and temperature-dependent chemical reaction. The proposed model was implemented in the finite element code ABAQUS by the user subroutine VUMAT. A series of three-dimensional mesoscale models were constructed and calculated under low-strength impact loading scenarios from 100m/s to 600m/s where only the first wave transit is studied. Crystal anisotropy and microstructural heterogeneity are responsible for the nonuniform stress field and fluctuations of the stress wave front. At a critical impact velocity (≥300m/s), a chemical reaction is triggered because the temperature contributed by the volumetric and plastic works is sufficiently high. Physical quantities, including stress, temperature, and extent of reaction, are homogenized from those across the microstructure at the mesoscale to compare with macroscale measurements, which will advance the continuum-level models. The framework presented in this study has important implications in understanding hot spot ignition processes and improving predictive capabilities in energetic materials. Copyright © 2016 Elsevier B.V. All rights reserved.

Childrearing Violence and Child Adjustment Following Exposure to Kenyan Post-election Violence.

Science.gov (United States)

Skinner, Ann T; Oburu, Paul; Lansford, Jennifer E; Bacchini, Dario

2014-01-01

This study examines parents' and children's exposure to short-term political violence and the relation between childrearing violence and child adjustment following widespread violence that erupted in Kisumu, Kenya after the disputed presidential election in December 2007. Mothers of 100 Luo children (mean age = 8.46 years, 61% female) reported on their own use of childrearing violence at Time 1, approximately 4 months after the disputed election, and again at Times 2 ( n = 95) and 3 ( n = 95), approximately 12 and 24 months later, respectively. At Time 2, mothers reported about post-election violence directed at them and about their children's exposure to post-election violence. Children reported about their own externalizing behaviors at Times 1, 2, and 3. Children's exposure to post-election violence was related to Time 2 externalizing behavior, and childrearing violence at Time 1 predicted child externalizing behavior at Time 2. Exposure to post-election violence was not directly related to either childrearing violence or children's externalizing behavior by Time 3, although children's externalizing at Time 2 predicted more childrearing violence at Time 3. These results support earlier work that links childrearing violence and children's exposure to political violence with increases in child externalizing behavior, but examined these links in the under-studied area of short-term political violence. Even though sudden and severe political violence may subside significantly in weeks or months, increased attention to long-term effects on parenting and child adjustment is warranted.

Chernobyl explosion bombshell

International Nuclear Information System (INIS)

Martin, S.; Arnott, D.

1988-01-01

It is suggested that the explosion at the Chernobyl-4 reactor in April 1986 was a nuclear explosion. The evidence for this is examined. The sequence of events at Chernobyl is looked at to see if the effects were like those from a nuclear explosion. The question of whether a United Kingdom reactor could go prompt critical is discussed. It is concluded that prompt criticality excursions are possible, but the specific Chernobyl sequence is impossible. (UK)

Simulation of thermal phenomena expected in fuel coolant interactions in LMFBRs

International Nuclear Information System (INIS)

Yasin, J.

1976-12-01

High pressures and mechanical work may result when thermal energy is transferred from molten fuel to the coolant in a Liquid Metal Fast Breeder Reactor core meltdown accident. Two aspects of the interaction are examined in the thesis. First, the formation of high pressure pulses termed ''Vapor Explosions,'' and second, the distribution of the molten material into smaller particles, termed ''Fragmentation'', are studied. To understand the nature of the interaction simulant materials were used. Molten bismuth, molten tin and molten glass were dropped into water under various conditions. The interactions were recorded using multiflash and high speed photographing techniques. The pressure pulses were measured using transducers and the debris was examined by photographing them with an electron microscope. It was observed that vapor explosions have thresholds which depend on the material being dropped, its temperature and the bath conditions. The vapor explosions were enhanced by stratifying the bath. It was also noticed that the intensity of the vapor explosion depends on the way the molten drop fragmented in the initial stages of the interaction. The experiments with glass showed that the mode of fragmentation is important in determining when and if a vapor explosion is to be expected. The glass fragmented extensively but without any accompanying vapor explosion. The electron microscope photographs of the glass debris showed that thermal stress and surface tension phenomenon are apparently the cause of the fragmentation

A study on vapor explosions

International Nuclear Information System (INIS)

Takagi, N.; Shoji, M.

1979-01-01

An experimental study was carried out for vapor explosions of molten tin falling in water. For various initial metal temperatures and subcooling of water, transient pressure of the explosions, relative frequency of the explosions and the position where the explosions occur were measured in detail. The influence of ambient pressure was also investigated. From the results, it was concluded that the vapor explosion is closely related to the collapse of a vapor film around the molten metal. (author)

Development of a Risk-Based Decision-Support-Model for Protecting an Urban Medical Center from a Nuclear Explosion

International Nuclear Information System (INIS)

Ben-Dor, G.; Shohet, I.M.; Ornai, D.; Brosh, B.

2014-01-01

Nuclear explosion is the worst man-made physical threat on the human society. The nuclear explosion includes several consequences, some of them are immediate and others are long term. The major influences are: long duration blast, extreme thermal release, nuclear radiations, and electro-magnetic pulse (EMP). Their damage range is very wide. When nuclear explosion occurs above or in an urban area it is possible that one or more medical centers will be affected. Medical centers include several layers of structures defined by their resistance capacity to the nuclear explosion influences, beginning with the structure's frame and ending with different systems and with vulnerable medical critical infrastructures such as communications, medical gas supply, etc. A comprehensive literature survey revealed that in spite of the necessity and the importance of medical centers in the daily life and especially in emergency and post nuclear explosion, there is a lack of research on this topic

Advances in neutron based bulk explosive detection

Science.gov (United States)

Gozani, Tsahi; Strellis, Dan

2007-08-01

Neutron based explosive inspection systems can detect a wide variety of national security threats. The inspection is founded on the detection of characteristic gamma rays emitted as the result of neutron interactions with materials. Generally these are gamma rays resulting from thermal neutron capture and inelastic scattering reactions in most materials and fast and thermal neutron fission in fissile (e.g.235U and 239Pu) and fertile (e.g.238U) materials. Cars or trucks laden with explosives, drugs, chemical agents and hazardous materials can be detected. Cargo material classification via its main elements and nuclear materials detection can also be accomplished with such neutron based platforms, when appropriate neutron sources, gamma ray spectroscopy, neutron detectors and suitable decision algorithms are employed. Neutron based techniques can be used in a variety of scenarios and operational modes. They can be used as stand alones for complete scan of objects such as vehicles, or for spot-checks to clear (or validate) alarms indicated by another inspection system such as X-ray radiography. The technologies developed over the last two decades are now being implemented with good results. Further advances have been made over the last few years that increase the sensitivity, applicability and robustness of these systems. The advances range from the synchronous inspection of two sides of vehicles, increasing throughput and sensitivity and reducing imparted dose to the inspected object and its occupants (if any), to taking advantage of the neutron kinetic behavior of cargo to remove systematic errors, reducing background effects and improving fast neutron signals.

Domestic violence

OpenAIRE

Tačík, Michal

2015-01-01

Domestic violence The present thesis deals with the phenomenon of domestic violence, from the substantive, procedural and criminological aspects. The first part defines the specifics of domestic violence, its signs and forms. It shows a typology of victims and perpetrators. It analyzes in detail the basic facts of the crimes that are the most commonly perpetrated forms of domestic violence. It also describes the sanctions and some of the treatment programs that are available for perpetrators ...

Association between Domestic Violence and School Violence: a preliminary analysis

Directory of Open Access Journals (Sweden)

Lúcia Cavalcanti de Albuquerque Williams

2008-07-01

Full Text Available Usually, one investigates marital violence, children victimization, and school violence in an isolated way. The aim of this paper is to highlight the relationship between domestic violence and school violence, suggesting actions to deal with these serious issues. With this goal in mind, two studies are described in this paper. The first one evaluates if boys who behave aggressively in school, in comparison with their non-aggressive peers, have more incidence of domestic violence exposure and victimization. The second study investigates if exposure to domestic violence and child victimization are factors associated with bullying. These studies indicated that there is a relation between the violence experienced in these two contexts; however they emphasize the need for further investigations with more participant and longitudinal studies. Teacher in-service training is suggested, aimed at: identifying students living in families with a history of domestic violence; supporting teachers and principals in case of disclosures in the school setting; social skills training for students; class discussions about healthy and non-violent family relationships and, psychotherapy referral to students who are victimized.

Violence in childhood, attitudes about partner violence, and partner violence perpetration among men in Vietnam

NARCIS (Netherlands)

Yount, K.M.; Huyen, T.P.; Tran, H.M.; Krause, K.H.; Schuler, S.R.; Hoang, T.A.; VanderEnde, K.; Kramer, M.R.

2014-01-01

Purpose: We assess the association of men’s exposure to violence in childhood—witnessing physical violence against one’s mother and being hit or beaten by a parent or adult relative—with their attitudes about intimate partner violence (IPV) against women. We explore whether men’s perpetration of IPV

Aspects regarding explosion risk assessment

Directory of Open Access Journals (Sweden)

Părăian Mihaela

2017-01-01

Full Text Available Explosive risk occurs in all activities involving flammable substances in the form of gases, vapors, mists or dusts which, in mixture with air, can generate an explosive atmosphere. As explosions can cause human losses and huge material damage, the assessment of the explosion risk and the establishment of appropriate measures to reduce it to acceptable levels according to the standards and standards in force is of particular importance for the safety and health of people and goods.There is no yet a recognized method of assessing the explosion risk, but regardless of the applied method, the likelihood of an explosive atmosphere occurrence has to be determined, together with the occurrence of an efficient ignition source and the magnitude of foreseeable consequences. In assessment processes, consequences analysis has a secondary importance since it’s likely that explosions would always involve considerable damage, starting from important material damages and up to human damages that could lead to death.The purpose of the work is to highlight the important principles and elements to be taken into account for a specific risk assessment. An essential element in assessing the risk of explosion in workplaces where explosive atmospheres may occur is technical installations and personal protective equipment (PPE that must be designed, manufactured, installed and maintained so that they cannot generate a source of ignition. Explosion prevention and protection requirements are governed by specific norms and standards, and a main part of the explosion risk assessment is related to the assessment of the compliance of the equipment / installation with these requirements.

Thermal properties of andesite from Popocatepetl and Volcán de Colima, México.

Science.gov (United States)

Cardenas-Sanchez, Enrique; De la Cruz-Reina, Servando; Varley, Nick

2015-04-01

The thermal conductivity (K), specific heat (Cp) and the coefficient of heat transfer surface (H) are the basic parameters to describe the process of cooling a volcanic rock fragment released in an explosive event. The analysis of the cooling process by conduction, convection and radiation of heat in volcanic rock fragments, has been limited to basalts, and various minerals such as olivine, pyroxene, quartz, etc. (Miao & Chen, 2014; Branlund & Hofmeister, 2012; Romine et al, 2012;. Schön, 2011; Stroberg et al, 2010;. Schatz & Simmons, 1972). There are no detailed studies on the thermal properties of the andesites, abundant in continental stratovolcanoes, and particularly susceptible from lava domes with frequent destruction processes, such as Popocatepetl and Volcan de Colima. Previously, we developed an algorithm for calculation of the grain-size distribution, degree of fragmentation, the thermal energy released and its possible correlation with Volcanic Explosive Index (VEI) from the cooling curves of fragments from vulcanian and strombolian explosions. These curves were obtained from sequences of time over incandescent deposits recorded at selected pixel thermal images of vulcanian activity in the Popocatepetl and Volcan de Colima, Mexico. However, the model was limited by the lack of thermal parameters of the andesites, forcing a first approximation using basalts data. We present a simple model for the cooling process using andesites samples from Popocatépetl and Volcan de Colima. First, the samples were subjected to a rounding process to minimize surface effects. Then, heated to 800 ° C were extracted from the muffle and cooling rate is measured. The thermal conductivity and coefficient of surface heat are determined using a thermal camera and three thermocouples embedded at various depths within the sample. An inversion method was implemented to determine the thermal properties parameters , by comparing the observed data regarding cooling model for a solid

Numerical modelling of the effect of using multi-explosives on the explosive forming of steel cones

OpenAIRE

De Vuyst, T; Kong, K; Djordjevic, N; Vignjevic, R; Campbell, JC; Hughes, K

2016-01-01

Modelling and analysis of underwater explosive forming process by using FEM and SPH formulation is presented in this work. The explosive forming of a steel cone is studied. The model setup includes a low carbon steel plate, plate holder, forming die as well as water and C4 explosive. The effect of multiple explosives on rate of targets deformation has been studied. Four different multi-explosives models have been developed and compared to the single explosive model. The formability of the ste...

Calorimetric studies and lessons on fires and explosions of a chemical plant producing CHP and DCPO

International Nuclear Information System (INIS)

Hsu, Jing-Ming; Su, Mao-Sheng; Huang, Chiao-Ying; Duh, Yih-Shing

2012-01-01

Highlights: ► We analyzed fire and explosion incidents in a plant producing CHP and DCPO. ► Data from calorimeters reveal causes and phenomena associated with the incidents. ► The credible worst scenario was thermal explosion. ► Incidents may be avoided by implementing DIERS methodology. - Abstract: Cumene hydroperoxide (CHP) has been used in producing phenol, dicumyl peroxide (DCPO) and as an initiator for synthesizing acrylonitrile–butadiene–styrene (ABS) resin by copolymerization in Taiwan. Four incidents of fire and explosion induced by thermal runaway reactions were occurred in a same plant producing CHP, DCPO and bis-(tert-butylperoxy isopropyl) benzene peroxide (BIBP). The fourth fire and explosion occurred in the CHP reactor that resulted in a catastrophic damage in reaction region and even spread throughout storage area. Descriptions on the occurrences of these incidents were assessed by the features of processes, reaction schemes and unexpected side reactions. Calorimetric data on thermokinetics and pressure were used for explaining the practical consequences or which the worst cases encountered in this kind of plant. Acceptable risk associated with emergency relief system design is vital for a plant producing organic peroxide. These basic data for designing an inherently safer plant can be conducted from adiabatic calorimetry. An encouraging deduction has been drawn here, these incidents may be avoided by the implementation of API RP 520, API RP 521, DIERS technology, OSHA 1910.119 and AIChE's CCPS recommended PSM elements.

Domestic violence

OpenAIRE

Kiurski Jasmina

2003-01-01

Since the 1960s, there has been growing awareness regarding the issue of domestic violence as a form of violence against women, which has been largely influenced by the work of feminist activist and scholars in North America and Europe (Dobash and Dobash 1992). Other terms have been used to describe the same phenomenon, including domestic abuse, spousal abuse, wife battering, marital violence, intimate partner violence. Though there is no doubt that this problem has existed for much more than...

Understanding sexual violence as a form of caste violence

OpenAIRE

Prachi Patil

2016-01-01

The paper attempts to understand narratives of sexual violence anchored within the dynamics of social location of caste and gender. Apparent caste-patriarchy and gender hierarchies which are at play in cases of sexual violence against lower-caste and dalit women speak about differential experiences of rape and sexual abuse that women have in India. The paper endeavours to establish that sexual violence is also a form of caste violence by rereading the unfortunate cases of Bhanwari Devi, Khair...

FAMILY VIOLENCE – MARRIAGE VIOLENCE WITH A FATAL OUTCOME

Directory of Open Access Journals (Sweden)

Lidija Kostic-Banovic

2006-04-01

Full Text Available Family violence represents an especially dangerous social form of violence by means of which the rights of an individual – a member of a family – to live, to have psychic, physical and sexual integrity, freedom, security and human dignity, have been violated. The term marriage violence entails every form of physical, sexual, psychic and economic abuse of women by husbands or illegitimate partner. The family violence represents a widespread form of crime, and since it has become dramatic and dynamic during the recent years, the need for a direct forensic processing of the violence consequences within this specific and sensitive social group has arisen. In accordance with what has been outlined above, three cases of extreme, systematic and continuous marriage violence with fatal consequences of the abused women, whose bodies have been abducted at the Forensics Institute in Nis, have been presented in this paper.

Mainstreaming domestic and gender-based violence into sociology and the criminology of violence.

Science.gov (United States)

Walby, Sylvia; Towers, Jude; Francis, Brian

2014-12-01

Sociological and criminological views of domestic and gender-based violence generally either dismiss it as not worthy of consideration, or focus on specific groups of offenders and victims (male youth gangs, partner violence victims). In this paper, we take a holistic approach to violence, extending the definition from that commonly in use to encompass domestic violence and sexual violence. We operationalize that definition by using data from the latest sweep of the Crime Survey for England and Wales. By so doing, we identify that violence is currently under-measured and ubiquitous; that it is gendered, and that other forms of violence (family violence, acquaintance violence against women) are equally of concern. We argue that violence studies are an important form of activity for sociologists.

Mainstreaming domestic and gender-based violence into sociology and the criminology of violence

Science.gov (United States)

Walby, Sylvia; Towers, Jude; Francis, Brian

2014-01-01

Sociological and criminological views of domestic and gender-based violence generally either dismiss it as not worthy of consideration, or focus on specific groups of offenders and victims (male youth gangs, partner violence victims). In this paper, we take a holistic approach to violence, extending the definition from that commonly in use to encompass domestic violence and sexual violence. We operationalize that definition by using data from the latest sweep of the Crime Survey for England and Wales. By so doing, we identify that violence is currently under-measured and ubiquitous; that it is gendered, and that other forms of violence (family violence, acquaintance violence against women) are equally of concern. We argue that violence studies are an important form of activity for sociologists. PMID:25641992

Analysis and modeling of flow-blockage-induced steam explosion events in the high-flux isotope reactor

International Nuclear Information System (INIS)

Taleyarkhan, R.P.; Georgevich, V.; Nestor, C.W.; Gat, U.; Lepard, B.L.; Cook, D.H.; Freels, J.; Chang, S.J.; Luttrell, C.; Gwaltney, R.C.

1994-01-01

This article provides a perspective overview of the analysis and modeling work done to evaluate the threat from steam explosion loads in the High-Flux Isotope Reactor (HFIR) during flow blockage events. The overall work scope included modeling and analysis of core-melt initiation, melt propagation, bounding and best-estimate steam explosion energetics, vessel failure from fracture, bolts failure from exceedance of elastic limits, and, finally, missile evolution and transport. Aluminum ignition was neglected. Evaluations indicated that a thermally driven steam explosion with more than 65 MJ of energy insertion in the core region over several milliseconds would be needed to cause a sufficiently energetic missile with a capacity to cause early confinement failure. This amounts to about 65% of the HFIR core mass melting and participating in a steam explosion. Conservative melt propagation analyses have indicated that at most only 24% of the HFIR core mass could melt during flow blockage events under full-power conditions. 19 refs., 11 figs

SUPERFUND TREATABILITY CLEARINGHOUSE: INCINERATION TEST OF EXPLOSIVES CONTAMINATED SOILS AT SAVANNA ARMY DEPOT ACTIVITY, SAVANNA, ILLINOIS

Science.gov (United States)

The primary objective of these tests was to demonstrate the effectiveness of incineration as a decontamination method for explosives contaminated sails. A pilot-scale rotary kiln incinerator, manufactured by ThermAll, Inc., was used to treat both sandy and clayey...

Simulation of TROI steam explosion behaviour using the COMETA code

International Nuclear Information System (INIS)

Arun Kumar Nayak; Hyun Sun Park; Bal Raj Sehgal; Alessandro Annunziato

2005-01-01

Full text of publication follows: During a severe accident in a nuclear reactor, the core can melt and the molten corium while interacting with water may cause an energetic fuel coolant interaction which is known as steam explosion. Such phenomena can occur inside the reactor vessel during flooding of a degraded core or when molten corium falls into the lower head filled with water. Similar phenomena may occur outside the reactor vessel when molten corium is ejected into a flooded reactor cavity or into the flooded containment after the vessel failure. The interaction of molten corium with water is one of the most complex thermal hydraulic and chemical phenomena. Recently in the TROI test series carried out at KAERI (Korean Atomic Energy Research Institute) in Korea, steam explosions were observed. In those tests, the UO 2 /ZrO 2 compositions were close to that of prototypic case. In this paper, we have numerically simulated the melt coolant interaction of TROI tests using the computer code, COMETA (Core MElt Thermalhydraulic Analysis) developed by JRC (Joint Research Center), at Ispra in Italy. The COMETA code was primarily developed to analyse, with sufficient detail, both the thermal-hydraulics and the fuel fragmentation phenomena during the melt quenching tests as conducted in the FARO facility. The code solves the conservation equations of mass, momentum and energy for the fluid using a conventional two-fluid model. Fuel fragmentation model considers the molten jet, its break up in drops and accumulation as fused-debris on the bottom. An explicit coupling between the thermal hydraulics and fuel fragmentation for the energy transfer is considered. The code has been extensively validated in the past for melt quenching in a series of experiments in the FARO facility. In this work, we first simulated the pre-mix and triggering phases of the TROI-13 tests for which the test data were available. The melt jet trajectory, void fraction and pressure profile were

FAMILY VIOLENCE – MARRIAGE VIOLENCE WITH A FATAL OUTCOME

OpenAIRE

Lidija Kostic-Banovic; Ljubisa Milosavljevic; Radovan Karadzic; Aleksandra Antovic

2006-01-01

Family violence represents an especially dangerous social form of violence by means of which the rights of an individual – a member of a family – to live, to have psychic, physical and sexual integrity, freedom, security and human dignity, have been violated. The term marriage violence entails every form of physical, sexual, psychic and economic abuse of women by husbands or illegitimate partner. The family violence represents a widespread form of crime, and since it has become dramatic and d...

High-speed imaging of explosive eruptions: applications and perspectives

Science.gov (United States)

Taddeucci, Jacopo; Scarlato, Piergiorgio; Gaudin, Damien; Capponi, Antonio; Alatorre-Ibarguengoitia, Miguel-Angel; Moroni, Monica

2013-04-01

Explosive eruptions, being by definition highly dynamic over short time scales, necessarily call for observational systems capable of relatively high sampling rates. "Traditional" tools, like as seismic and acoustic networks, have recently been joined by Doppler radar and electric sensors. Recent developments in high-speed camera systems now allow direct visual information of eruptions to be obtained with a spatial and temporal resolution suitable for the analysis of several key eruption processes. Here we summarize the methods employed to gather and process high-speed videos of explosive eruptions, and provide an overview of the several applications of these new type of data in understanding different aspects of explosive volcanism. Our most recent set up for high-speed imaging of explosive eruptions (FAMoUS - FAst, MUltiparametric Set-up,) includes: 1) a monochrome high speed camera, capable of 500 frames per second (fps) at high-definition (1280x1024 pixel) resolution and up to 200000 fps at reduced resolution; 2) a thermal camera capable of 50-200 fps at 480-120x640 pixel resolution; and 3) two acoustic to infrasonic sensors. All instruments are time-synchronized via a data logging system, a hand- or software-operated trigger, and via GPS, allowing signals from other instruments or networks to be directly recorded by the same logging unit or to be readily synchronized for comparison. FAMoUS weights less than 20 kg, easily fits into four, hand-luggage-sized backpacks, and can be deployed in less than 20' (and removed in less than 2', if needed). So far, explosive eruptions have been recorded in high-speed at several active volcanoes, including Fuego and Santiaguito (Guatemala), Stromboli (Italy), Yasur (Vanuatu), and Eyjafiallajokull (Iceland). Image processing and analysis from these eruptions helped illuminate several eruptive processes, including: 1) Pyroclasts ejection. High-speed videos reveal multiple, discrete ejection pulses within a single Strombolian

General phenomenology of underground nuclear explosions

International Nuclear Information System (INIS)

Derlich, S.; Supiot, F.

1969-01-01

An essentially qualitatively description is given of the phenomena related to underground nuclear explosions (explosion of a single unit, of several units in line, and simultaneous explosions). In the first chapter are described the phenomena which are common to contained explosions and to explosions forming craters (formation and propagation of a shock-wave causing the vaporization, the fusion and the fracturing of the medium). The second chapter describes the phenomena related to contained explosions (formation of a cavity with a chimney). The third chapter is devoted to the phenomenology of test explosions which form a crater; it describes in particular the mechanism of formation and the different types of craters as a function of the depth of the explosion and of the nature of the ground. The aerial phenomena connected with explosions which form a crater: shock wave in the air and focussing at a large distance, and dust clouds, are also dealt with. (authors) [fr

Violence in childhood, attitudes about partner violence, and partner violence perpetration among men in Vietnam.

Science.gov (United States)

Yount, Kathryn M; Pham, Huyen Tran; Minh, Tran Hung; Krause, Kathleen H; Schuler, Sidney Ruth; Anh, Hoang Tu; VanderEnde, Kristin; Kramer, Michael R

2014-05-01

We assess the association of men's exposure to violence in childhood-witnessing physical violence against one's mother and being hit or beaten by a parent or adult relative-with their attitudes about intimate partner violence (IPV) against women. We explore whether men's perpetration of IPV mediates this relationship and whether men's attitudes about IPV mediate any relationship of exposure to violence in childhood with perpetration of IPV. Five hundred twenty-two married men 18-51 years in Vietnam were interviewed. Multivariate regressions for ordinal and binary responses were estimated to assess these relationships. Compared with men experiencing neither form of violence in childhood, men experiencing either or both had higher adjusted odds of reporting more reasons to hit a wife (aOR, 1.43; 95% CI, 1.03-2.00 and aOR, 1.66; 95% CI, 1.05-2.64, respectively). Men's lifetime perpetration of IPV accounted fully for these associations. Compared with men experiencing neither form of violence in childhood, men experiencing either or both had higher adjusted odds of ever perpetrating IPV (aOR, 3.28; 95% CI, 2.15-4.99 and aOR, 4.56; 95% CI, 2.90-7.17, respectively). Attitudes about IPV modestly attenuated these associations. Addressing violence in childhood is needed to change men's risk of perpetrating IPV and greater subsequent justification of it. Copyright © 2014 Elsevier Inc. All rights reserved.

School Violence

Science.gov (United States)

Schonfeld, Irvin Sam

2006-01-01

The purpose of this chapter is threefold. First, the chapter summarizes what is known about the prevalence of violence and weapons in U.S. schools. Second, the chapter examines theories that bear on school violence and the empirical evidence linked to those theories. Third, the chapter looks at attempts to prevent school violence and,…

Thermal stability and kinetics of decomposition of ammonium nitrate in the presence of pyrite

International Nuclear Information System (INIS)

Gunawan, Richard; Zhang Dongke

2009-01-01

The interaction between ammonium nitrate based industrial explosives and pyrite-rich minerals in mining operations can lead to the occurrence of spontaneous explosion of the explosives. In an effort to provide a scientific basis for safe applications of industrial explosives in reactive mining grounds containing pyrite, ammonium nitrate decomposition, with and without the presence of pyrite, was studied using a simultaneous Differential Scanning Calorimetry and Thermogravimetric Analyser (DSC-TGA) and a gas-sealed isothermal reactor, respectively. The activation energy and the pre-exponential factor of ammonium nitrate decomposition were determined to be 102.6 kJ mol -1 and 4.55 x 10 7 s -1 without the presence of pyrite and 101.8 kJ mol -1 and 2.57 x 10 9 s -1 with the presence of pyrite. The kinetics of ammonium nitrate decomposition was then used to calculate the critical temperatures for ammonium nitrate decomposition with and without the presence of pyrite, based on the Frank-Kamenetskii model of thermal explosion. It was shown that the presence of pyrite reduces the temperature for, and accelerates the rate of, decomposition of ammonium nitrate. It was further shown that pyrite can significantly reduce the critical temperature of ammonium nitrate decomposition, causing undesired premature detonation of the explosives. The critical temperature also decreases with increasing diameter of the blast holes charged with the explosive. The concept of using the critical temperature as indication of the thermal stability of the explosives to evaluate the risk of spontaneous explosion was verified in the gas-sealed isothermal reactor experiments.

Thermal stability and kinetics of decomposition of ammonium nitrate in the presence of pyrite.

Science.gov (United States)

Gunawan, Richard; Zhang, Dongke

2009-06-15

The interaction between ammonium nitrate based industrial explosives and pyrite-rich minerals in mining operations can lead to the occurrence of spontaneous explosion of the explosives. In an effort to provide a scientific basis for safe applications of industrial explosives in reactive mining grounds containing pyrite, ammonium nitrate decomposition, with and without the presence of pyrite, was studied using a simultaneous Differential Scanning Calorimetry and Thermogravimetric Analyser (DSC-TGA) and a gas-sealed isothermal reactor, respectively. The activation energy and the pre-exponential factor of ammonium nitrate decomposition were determined to be 102.6 kJ mol(-1) and 4.55 x 10(7)s(-1) without the presence of pyrite and 101.8 kJ mol(-1) and 2.57 x 10(9)s(-1) with the presence of pyrite. The kinetics of ammonium nitrate decomposition was then used to calculate the critical temperatures for ammonium nitrate decomposition with and without the presence of pyrite, based on the Frank-Kamenetskii model of thermal explosion. It was shown that the presence of pyrite reduces the temperature for, and accelerates the rate of, decomposition of ammonium nitrate. It was further shown that pyrite can significantly reduce the critical temperature of ammonium nitrate decomposition, causing undesired premature detonation of the explosives. The critical temperature also decreases with increasing diameter of the blast holes charged with the explosive. The concept of using the critical temperature as indication of the thermal stability of the explosives to evaluate the risk of spontaneous explosion was verified in the gas-sealed isothermal reactor experiments.

The overlap between offending trajectories, criminal violence, and intimate partner violence.

Science.gov (United States)

Piquero, Alex R; Theobald, Delphine; Farrington, David P

2014-03-01

This article investigates the overlap between offending trajectories, criminal violence, and intimate partner violence (IPV) and the factors associated with these behaviors. Knowledge on these questions is relevant to theory and policy. For the former, this article considers the extent to which specific theories are needed for understanding crime, criminal violence, and/or IPV, whereas for the latter, it may suggest specific offense- and offender-based policies. We use data from the Cambridge Study in Delinquent Development that traces the offending, criminal violence, and IPV of males to age 50. Findings show that there is significant overlap between criminal violence and IPV, high-rate offending trajectories have increased odds of criminal violence and IPV, and early childhood risk factors have no additional effect on criminal violence and IPV in adulthood over and above the offending trajectories.

30 CFR 77.307 - Thermal dryers; location and installation; general.

Science.gov (United States)

2010-07-01

... where the heat, sparks, flames, or coal dust from the system might cause a fire or explosion. (b... LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Thermal Dryers § 77.307 Thermal dryers; location and installation; general...

Sensitivities of ionic explosives

Science.gov (United States)

Politzer, Peter; Lane, Pat; Murray, Jane S.

2017-03-01

We have investigated the relevance for ionic explosive sensitivity of three factors that have been demonstrated to be related to the sensitivities of molecular explosives. These are (1) the maximum available heat of detonation, (2) the amount of free space per molecule (or per formula unit) in the crystal lattice and (3) specific features of the electrostatic potential on the molecular or ionic surface. We find that for ionic explosives, just as for molecular ones, there is an overall tendency for impact sensitivity to increase as the maximum detonation heat release is greater. This means that the usual emphasis upon designing explosives with large heats of detonation needs to be tempered somewhat. We also show that a moderate detonation heat release does not preclude a high level of detonation performance for ionic explosives, as was already demonstrated for molecular ones. Relating the free space per formula unit to sensitivity may require a modified procedure for ionic explosives; this will continue to be investigated. Finally, an encouraging start has been made in linking impact sensitivities to the electrostatic potentials on ionic surfaces, although limited so far to ammonium salts.

VIOLENCE DRESSED IN HUMOR: COMEDIC VIOLENCE IN ADVERTISING

OpenAIRE

Camelia Gradinaru

2016-01-01

This paper investigates the concepts of humor and violence and their complex relationships contextualised in the advertising domain. Thus, the main theories of humor and the most important elements from media violence paradigms are critically pointed out. The effects of comedic violence in advertising may be positive (great involvement with the ad message, retention of brand information, higher pass-along probability), and also negative (offending the audience, desensitization, damaging the r...

Nano-powder production by electrical explosion of wires

International Nuclear Information System (INIS)

Mao Zhiguo; Zou Xiaobing; Wang Xinxin; Jiang Weihua

2010-01-01

A device for nano-powder production by electrical explosion of wires was designed and built. Eight wires housed in the discharge chamber are exploded one by one before opening the chamber for the collection of the produced nano-powder. To increase the rate of energy deposition into a wire, the electrical behavior of the discharge circuit including the exploding wire was simulated. The results showed that both reducing the circuit inductance and reducing the capacitance of the energy-storage capacitor (keeping the storage energy constant) can increase the energy deposition rate. To better understand the physical processes of the nano-powder formation by the wire vapor, a Mach-Zehnder interferometer was used to record the time evolution of the wire vapor as well as the plasma. A thermal expansion lag of the dense vapor core as well as more than one times of the vapor burst was observed for the first time. Finally, nano-powders of titanium nitride, titanium dioxide, copper oxides and zinc oxide were produced by electrical explosion of wires. (authors)

The Culture of Violence in the Final Phase of the Apartheid: South Africa c. 1984-1994

Directory of Open Access Journals (Sweden)

Hilda Varela Barraza

2014-05-01

Full Text Available Since the 1970s, an organic crisis of the apartheid system began in South Africa, and it intensified in the beginning of the 1980s with the explosion of a new popular revolt, known as the township revolt. This article deals with a time period of approximately one decade (c. 1984-1994, characterized by a qualitative change in the culture of violence, which began in September 1984 but was triggered by the 1983 constitutional referendum and which symbolically ended with the first democratic election of 1984.

Cell phone explosion.

Science.gov (United States)

Atreya, Alok; Kanchan, Tanuj; Nepal, Samata; Pandey, Bhuwan Raj

2016-03-01

Cell phone explosions and resultant burn injuries are rarely reported in the scientific literature. We report a case of cell phone explosion that occurred when a young male was listening to music while the mobile was plugged in for charging. © The Author(s) 2015.

A structured approach to forensic study of explosions: The TNO Inverse Explosion Analysis tool

NARCIS (Netherlands)

Voort, M.M. van der; Wees, R.M.M. van; Brouwer, S.D.; Jagt-Deutekom, M.J. van der; Verreault, J.

2015-01-01

Forensic analysis of explosions consists of determining the point of origin, the explosive substance involved, and the charge mass. Within the EU FP7 project Hyperion, TNO developed the Inverse Explosion Analysis (TNO-IEA) tool to estimate the charge mass and point of origin based on observed damage

Intimate Partner Violence Perpetration by Court-Ordered Men: Distinctions among Subtypes of Physical Violence, Sexual Violence, Psychological Abuse, and Stalking

Science.gov (United States)

Hall, Jeffrey E.; Walters, Mikel L.; Basile, Kathleen C.

2012-01-01

This study continues previous work documenting the structure of violence perpetrated by males against their female intimate partners. It assesses the construct validity of a measurement model depicting associations among eight subtypes of perpetration: moderate physical violence, severe physical violence, forced or coerced sexual violence, sexual…

Calorimetric studies and lessons on fires and explosions of a chemical plant producing CHP and DCPO

Energy Technology Data Exchange (ETDEWEB)

Hsu, Jing-Ming; Su, Mao-Sheng; Huang, Chiao-Ying [Department of Occupational Safety and Health, Chia Nan University of Pharmacy and Science, Tainan, Taiwan, ROC (China); Duh, Yih-Shing, E-mail: yihshingduh@yahoo.com.tw [Department of Safety, Health and Environmental Engineering, National United University, No. 1 Lien-Da, Miaoli, Taiwan, ROC (China)

2012-05-30

Highlights: Black-Right-Pointing-Pointer We analyzed fire and explosion incidents in a plant producing CHP and DCPO. Black-Right-Pointing-Pointer Data from calorimeters reveal causes and phenomena associated with the incidents. Black-Right-Pointing-Pointer The credible worst scenario was thermal explosion. Black-Right-Pointing-Pointer Incidents may be avoided by implementing DIERS methodology. - Abstract: Cumene hydroperoxide (CHP) has been used in producing phenol, dicumyl peroxide (DCPO) and as an initiator for synthesizing acrylonitrile-butadiene-styrene (ABS) resin by copolymerization in Taiwan. Four incidents of fire and explosion induced by thermal runaway reactions were occurred in a same plant producing CHP, DCPO and bis-(tert-butylperoxy isopropyl) benzene peroxide (BIBP). The fourth fire and explosion occurred in the CHP reactor that resulted in a catastrophic damage in reaction region and even spread throughout storage area. Descriptions on the occurrences of these incidents were assessed by the features of processes, reaction schemes and unexpected side reactions. Calorimetric data on thermokinetics and pressure were used for explaining the practical consequences or which the worst cases encountered in this kind of plant. Acceptable risk associated with emergency relief system design is vital for a plant producing organic peroxide. These basic data for designing an inherently safer plant can be conducted from adiabatic calorimetry. An encouraging deduction has been drawn here, these incidents may be avoided by the implementation of API RP 520, API RP 521, DIERS technology, OSHA 1910.119 and AIChE's CCPS recommended PSM elements.

Shock waves & explosions

CERN Document Server

Sachdev, PL

2004-01-01

Understanding the causes and effects of explosions is important to experts in a broad range of disciplines, including the military, industrial and environmental research, aeronautic engineering, and applied mathematics. Offering an introductory review of historic research, Shock Waves and Explosions brings analytic and computational methods to a wide audience in a clear and thorough way. Beginning with an overview of the research on combustion and gas dynamics in the 1970s and 1980s, the author brings you up to date by covering modeling techniques and asymptotic and perturbative methods and ending with a chapter on computational methods.Most of the book deals with the mathematical analysis of explosions, but computational results are also included wherever they are available. Historical perspectives are provided on the advent of nonlinear science, as well as on the mathematical study of the blast wave phenomenon, both when visualized as a point explosion and when simulated as the expansion of a high-pressure ...

Intermittent Explosive Disorder

Directory of Open Access Journals (Sweden)

Lut Tamam

2011-09-01

Full Text Available Intermittent explosive disorder is an impulse control disorder characterized by the occurrence of discrete episodes of failure to resist aggressive impulses that result in violent assault or destruction of property. Though the prevalence intermittent explosive disorder has been reported to be relatively rare in frontier studies on the field, it is now common opinion that intermittent explosive disorder is far more common than previously thought especially in clinical psychiatry settings. Etiological studies displayed the role of both psychosocial factors like childhood traumas and biological factors like dysfunctional neurotransmitter systems and genetics. In differential diagnosis of the disorder, disorders involving agression as a symptom such as alcohol and drug intoxication, antisocial and borderline personality disorders, personality changes due to general medical conditions and behavioral disorder should be considered. A combination of pharmacological and psychotherapeutic approaches are suggested in the treatment of the disorder. This article briefly reviews the historical background, diagnostic criteria, epidemiology, etiology and treatment of intermittent explosive disorder.

Free radical explosive composition

Science.gov (United States)

Walker, Franklin E.; Wasley, Richard J.

1979-01-01

An improved explosive composition is disclosed and comprises a major portion of an explosive having a detonation velocity between about 1500 and 10,000 meters per second and a minor amount of a getter additive comprising a compound or mixture of compounds capable of capturing or deactivating free radicals or ions under mechanical or electrical shock conditions and which is not an explosive. Exemplary getter additives are isocyanates, olefins and iodine.

Anger Mediates the Relation between Violence Exposure and Violence Perpetration in Incarcerated Boys

Science.gov (United States)

Kimonis, Eva R.; Ray, James V.; Branch, Jessica R.; Cauffman, Elizabeth

2011-01-01

Youth who are exposed to violence are more likely to perpetrate violence. Incarcerated youth are a special population that is at a significantly greater risk for violent offending because of their relatively greater rates of violence exposure. Two important outcomes of violence exposure that may help explain its link with violence perpetration are…

Effects of neutrino trapping on supernova explosions

International Nuclear Information System (INIS)

Takahara, Mariko; Sato, Katsuhiko

1982-01-01

Effects of neutrino trapping on the mass ejection from the stellar cores are investigated with the aid of a simplified equation of state under the assumption of adiabatic collapse. It is found that mass ejection becomes violent only if the ratio of the trapped leptons to baryons, Y sub(L), lies in an appropriate range. If the value of Y sub(L) lies out of this range, mass ejection is difficult. It is also shown that as the thermal stiffness of the shocked matter increases, the range necessary for the violent mass ejection becomes wider. Possibilities of supernova explosion are discussed on the basis of these results. (author)

Spot test kit for explosives detection

Science.gov (United States)

Pagoria, Philip F; Whipple, Richard E; Nunes, Peter J; Eckels, Joel Del; Reynolds, John G; Miles, Robin R; Chiarappa-Zucca, Marina L

2014-03-11

An explosion tester system comprising a body, a lateral flow membrane swab unit adapted to be removeably connected to the body, a first explosives detecting reagent, a first reagent holder and dispenser operatively connected to the body, the first reagent holder and dispenser containing the first explosives detecting reagent and positioned to deliver the first explosives detecting reagent to the lateral flow membrane swab unit when the lateral flow membrane swab unit is connected to the body, a second explosives detecting reagent, and a second reagent holder and dispenser operatively connected to the body, the second reagent holder and dispenser containing the second explosives detecting reagent and positioned to deliver the second explosives detecting reagent to the lateral flow membrane swab unit when the lateral flow membrane swab unit is connected to the body.

Explosive X-point collapse in relativistic magnetically dominated plasma

Science.gov (United States)

Lyutikov, Maxim; Sironi, Lorenzo; Komissarov, Serguei S.; Porth, Oliver

2017-12-01

The extreme properties of the gamma-ray flares in the Crab nebula present a clear challenge to our ideas on the nature of particle acceleration in relativistic astrophysical plasma. It seems highly unlikely that standard mechanisms of stochastic type are at work here and hence the attention of theorists has switched to linear acceleration in magnetic reconnection events. In this series of papers, we attempt to develop a theory of explosive magnetic reconnection in highly magnetized relativistic plasma which can explain the extreme parameters of the Crab flares. In the first paper, we focus on the properties of the X-point collapse. Using analytical and numerical methods (fluid and particle-in-cell simulations) we extend Syrovatsky's classical model of such collapse to the relativistic regime. We find that the collapse can lead to the reconnection rate approaching the speed of light on macroscopic scales. During the collapse, the plasma particles are accelerated by charge-starved electric fields, which can reach (and even exceed) values of the local magnetic field. The explosive stage of reconnection produces non-thermal power-law tails with slopes that depend on the average magnetization . For sufficiently high magnetizations and vanishing guide field, the non-thermal particle spectrum consists of two components: a low-energy population with soft spectrum that dominates the number census; and a high-energy population with hard spectrum that possesses all the properties needed to explain the Crab flares.

Nuclear explosives and hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Cohen, P

1971-10-01

A nuclear explosive 12 in. in diam and producing very little tritium is feasible in France. Such a device would be well adapted for contained nuclear explosions set off for the purpose of hydrocarbon storage or stimulation. The different aspects of setting off the explosive are reviewed. In the particular case of gas storage in a nuclear cavity in granite, it is demonstrated that the dose of irradiation received is extremely small. (18 refs.)

Girls, Crime and Violence: Toward a Feminist Theory of Female Violence

Directory of Open Access Journals (Sweden)

Kerry Carrington

2013-09-01

Full Text Available Rises recorded for girls’ violence in countries like Australia, Canada, United Kingdom and United States have been hotly contested. One view is these rising rates of violence are an artefact of new forms of policy, policing, criminalisation and social control over young women. Another view is that young women may indeed have become more violent as they have increasingly participated in youth subcultural activities involving gangs and drugs, and cyber-cultural activities that incite and reward girls’ violence. Any comprehensive explanation will need to address how a complex interplay of cultural, social, behavioural, and policy responses contribute to these rises. This article argues that there is no singular cause, explanation or theory that accounts for the rises in adolescent female violence, and that many of the simple explanations circulating in popular culture are driven by an anti-feminist ideology. By concentrating on females as victims of violence and very rarely as perpetrators, feminist criminology has for the most part ducked the thorny issue of female violence, leaving a discursive space for anti-feminist sentiment to reign. The article concludes by arguing the case for developing a feminist theory of female violence.Rises recorded for girls’ violence in countries like Australia, Canada, United Kingdom and United States have been hotly contested. One view is these rising rates of violence are an artefact of new forms of policy, policing, criminalisation and social control over young women. Another view is that young women may indeed have become more violent as they have increasingly participated in youth subcultural activities involving gangs and drugs, and cyber-cultural activities that incite and reward girls’ violence. Any comprehensive explanation will need to address how a complex interplay of cultural, social, behavioural, and policy responses contribute to these rises. This article argues that there is no singular

Physicochemical analysis of explosions due to impact in mixed paste propellants

Energy Technology Data Exchange (ETDEWEB)

Dubovik, Aleksandr V. [Institute of Chemical Physics, Russian Academy of Science, 117977, Kosygin Street 4, Moscow (Russian Federation)

2005-09-01

An analysis has been performed on the impact sensitivity of paste explosive materials (PEM) with continuous physical structure containing air cavities of various sizes. It is shown that the sensitivities of PEMs based on ammonium perchlorate are strongly influenced by the extent of oxidizer decomposition during the low-temperature stages of thermal decomposition. Mechanically non-uniform PEMs are well sensitized by air bubbles of an optimum size. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

Acceptability of Family Violence: Underlying Ties Between Intimate Partner Violence and Child Abuse.

Science.gov (United States)

Gracia, Enrique; Rodriguez, Christina M; Martín-Fernández, Manuel; Lila, Marisol

2017-05-01

Intimate partner violence (IPV) and child abuse (CA) are two forms of family violence with shared qualities and risk factors, and are forms of violence that tend to overlap. Acceptability of violence in partner relationships is a known risk factor in IPV just as acceptability of parent-child aggression is a risk factor in CA. We hypothesized that these acceptability attitudes may be linked and represent the expression of a general, underlying nonspecific acceptance of violence in close family relationships. The sample involved 164 male IPV offenders participating in a batterer intervention program. Implicit measures, which assess constructs covertly to minimize response distortions, were administered to assess acceptability of partner violence against women and acceptability of parent-child aggression. To determine whether acceptability attitudes regarding both forms of violence were related to a higher order construct tapping general acceptance of family violence, Bayesian confirmatory factor analyses were conducted. Findings supported a hierarchical (bifactor) model with a general factor expressing a nonspecific acceptance of family violence, and two specific factors reflecting acceptability of violence in intimate partner and parent-child relationships, respectively. This hierarchical model supporting a general acceptance of violence in close family relationships can inform future research aiming to better understand the connections between IPV and CA.

Gender Considerations in Violence.

Science.gov (United States)

Sorrentino, Renee; Friedman, Susan Hatters; Hall, Ryan

2016-12-01

The role of gender in violence is poorly understood. Research has shown that gender has an important and, at times, distinct role in the prediction of violence. However, this gender disparity diminishes in the setting of mental illness. The risk assessment of violence in women is largely based on research in violent men. There are distinct characteristics in female violence compared with male violence. Attention to these characteristics may lead to the development of gender-dependent tools that can be used to evaluate violence risk. Copyright © 2016 Elsevier Inc. All rights reserved.

Understanding Teen Dating Violence

Science.gov (United States)

Understanding Teen Dating Violence Fact Sheet 2014 Dating violence is a type of intimate partner violence. It occurs between two people in a close relationship. The nature of dating violence can be physical, emotional, or sexual. • Physical— This ...

Review of possible peaceful applications of nuclear explosions in the national economy of the Soviet Union

International Nuclear Information System (INIS)

Witherspoon, Paul A.

1970-01-01

The following review will give some of the current thinking of Soviet scientists and engineers on the possibilities of using nuclear explosions for peaceful purposes in the Soviet Union. This review is taken from a more detailed report that was presented under the same title by Soviet participants at an information-exchange meeting that was held in Vienna between the Soviet Union and the United States in April, 1969. Aside from a very brief review of one explosion in salt, the report does not give details on nuclear explosion effects (mechanical, seismic, radiation, or thermal). Rather, the report summarizes the results of design calculations and indicates the direction of Soviet planning for a variety of industrial applications. A complete translation of this report will be published by the Division of Technical Information and Education of AEC at Oakridge. (author)

Review of possible peaceful applications of nuclear explosions in the national economy of the Soviet Union

Energy Technology Data Exchange (ETDEWEB)

Witherspoon, Paul A [University of California, Berkeley (United States)

1970-05-15

The following review will give some of the current thinking of Soviet scientists and engineers on the possibilities of using nuclear explosions for peaceful purposes in the Soviet Union. This review is taken from a more detailed report that was presented under the same title by Soviet participants at an information-exchange meeting that was held in Vienna between the Soviet Union and the United States in April, 1969. Aside from a very brief review of one explosion in salt, the report does not give details on nuclear explosion effects (mechanical, seismic, radiation, or thermal). Rather, the report summarizes the results of design calculations and indicates the direction of Soviet planning for a variety of industrial applications. A complete translation of this report will be published by the Division of Technical Information and Education of AEC at Oakridge. (author)

30 CFR 77.1301 - Explosives; magazines.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosives; magazines. 77.1301 Section 77.1301... and Blasting § 77.1301 Explosives; magazines. (a) Detonators and explosives other than blasting agents shall be stored in magazines. (b) Detonators shall not be stored in the same magazine with explosives...

Domestic violence against children

OpenAIRE

Mihić Biljana D.

2002-01-01

In this paper the author is analysing definitions and basic notions related to domestic violence against children, as one of the most serious forms of violence. The special chapter deals with effects of violence against children and causes of domestic violence against them. Also, the author is analysing different forms of social reaction and considering the problem of legal regulation of mandatory reporting domestic violence against children.

CFD SIMULATION FOR DEMILITARIZATION OF RDX IN A ROTARY KILN BY THERMAL DECOMPOSITION

Directory of Open Access Journals (Sweden)

SI H. LEE

2017-06-01

Full Text Available Demilitarization requires the recovery and disposal of obsolete ammunition and explosives. Since open burning/detonation of hazardous waste has caused serious environmental and safety problems, thermal decomposition has emerged as one of the most feasible methods. RDX is widely used as a military explosive due to its high melting temperature and detonation power. In this work, the feasible conditions under which explosives can be safely incinerated have been investigated via a rotary kiln simulation. To solve this problem, phase change along with the reactions of RDX has been incisively analyzed. A global reaction mechanism consisting of condensed phase and gas phase reactions are used in Computational Fluid Dynamics simulation. User Defined Functions in FLUENT is utilized in this study to inculcate the reactions and phase change into the simulation. The results divulge the effect of temperature and the varying amounts of gas produced in the rotary kiln during the thermal decomposition of RDX. The result leads to the prospect of demilitarizing waste explosives to avoid the possibility of detonation.

Adult Violence with the Mother and Sibling as Predictors of Partner Violence

Science.gov (United States)

Hendy, Helen M.; Burns, Mary K.; Can, S. Hakan; Scherer, Cory R.

2012-01-01

The present study provides the first available evaluation of how violence with the mother and siblings during adulthood is associated with the occurrence of partner violence in young adults. Because a pattern of reciprocal partner violence is well documented, the authors hypothesized that reciprocal violence would also be found for adults and…

Animal violence demystified

NARCIS (Netherlands)

Natarajan, Deepa; Caramaschi, Doretta

2010-01-01

Violence has been observed in humans and animals alike, indicating its evolutionary/biological significance. However, violence in animals has often been confounded with functional forms of aggressive behavior. Currently, violence in animals is identified primarily as either a quantitative behavior

Study of the initiation and the escalade phases of a vapour explosion; Etude de la phase d'initiation et d'escalade d'une explosion de vapeur

Energy Technology Data Exchange (ETDEWEB)

Lamome, J

2007-09-15

The steam explosion triggering issue is discussed here by studying at the thermal fragmentation (small pressure perturbation) of a hot water droplet surrounded by a stable steam film. Fragmentation seems to be the consequence of local contacts between the droplet and the coolant. However, the exact mechanism altering the droplet following the above mentioned contacts is uncertain. After a study of the proportions in place, we realized a contact can fragment the droplet in a very short period of time. Therefore, we adopted an approach considering the contact as the explosion criteria. In order to validate this approach, we researched the explosion levels of the experimental variations based on the surrounding pressure and on the coolant's temperature. The model found again the experimental variations, the levels were found again with some uncertainty. The contact is obtained by 2 mechanisms inducing liquid's proximity: a steam film global compression due to the disturbance and the amplification of the interface defaults between the coolant and the steam. It appears it is the mechanism of global compression that explains mostly the experimental variations. Following these results, we conducted model's extrapolations in order to come as close as possible of the conditions in which steam explosion can occur on an industrial scale (i.e. in the water pressured nuclear reactors). (author)

Explosion metal welding

International Nuclear Information System (INIS)

Popoff, A.A.

1976-01-01

Process parameters pertaining to welding similar and dissimilar metals using explosives are reviewed. The discussion centers on the interrelationship of physical parameters which play a part in achieving desirable metallurgical results. Present activities in explosion metal welding at LASL are presented and shown how they related to the interests of the ERDA community

Sensitivity to friction for primary explosives.

Science.gov (United States)

Matyáš, Robert; Šelešovský, Jakub; Musil, Tomáš

2012-04-30

The sensitivity to friction for a selection of primary explosives has been studied using a small BAM friction apparatus. The probit analysis was used for the construction of a sensitivity curve for each primary explosive tested. Two groups of primary explosives were chosen for measurement (a) the most commonly used industrially produced primary explosives (e.g. lead azide, tetrazene, dinol, lead styphnate) and (b) the most produced improvised primary explosives (e.g. triacetone triperoxide, hexamethylenetriperoxide diamine, mercury fulminate, acetylides of heavy metals). A knowledge of friction sensitivity is very important for determining manipulation safety for primary explosives. All the primary explosives tested were carefully characterised (synthesis procedure, shape and size of crystals). The sensitivity curves obtained represent a unique set of data, which cannot be found anywhere else in the available literature. Copyright © 2012 Elsevier B.V. All rights reserved.

Ag-ZnO nanostructure for ANTA explosive molecule detection

Energy Technology Data Exchange (ETDEWEB)

Shaik, Ummar Pasha [Advanced Center of Research in High Energy Materials, University of Hyderabad, Hyderabad 500046 (India); Sangani, L. D. Varma [Centre for Advanced Studies in Electronics Science and Technology, School of Physics, University of Hyderabad (India); Gaur, Anshu [Department of Industrial Engineering, University of Trento, Via Sommarive9, Trento (Italy); Mohiddon, Md. Ahamad, E-mail: ahamed.vza@gmail.com [National Institute of Technology Andhra Pradesh, Tadepalliguem 534101, AP, India Phone : (+) 91-40-23134382, FAX: (+) 91-40-23010227 (India); Krishna, M. Ghanashyam [Advanced Center of Research in High Energy Materials, University of Hyderabad, Hyderabad 500046 (India); Centre for Advanced Studies in Electronics Science and Technology, School of Physics, University of Hyderabad (India); National Institute of Technology Andhra Pradesh, Tadepalliguem 534101, AP, India Phone : (+) 91-40-23134382, FAX: (+) 91-40-23010227 (India)

2016-05-23

Ag/ZnO nanostructure for surface enhanced Raman scattering application in the detection of ANTA explosive molecule is demonstrated. A highly rough ZnO microstructure was achieved by rapid thermal annealing of metallic Zn film. Different thickness Ag nanostructures are decorated over these ZnO microstructures by ion beam sputtering technique. Surface enhanced Raman spectroscopic studies carried out over Ag/ZnO substrates have shown three orders higher enhancement compared to bare Ag nanostructure deposited on the same substrate. The reasons behind such huge enhancement are discussed based on the morphology of the sample.

Zirconium hydride containing explosive composition

Science.gov (United States)

Walker, Franklin E.; Wasley, Richard J.

1981-01-01

An improved explosive composition is disclosed and comprises a major portion of an explosive having a detonation velocity between about 1500 and 10,000 meters per second and a minor amount of a donor additive comprising a non-explosive compound or mixture of non-explosive compounds which when subjected to an energy fluence of 1000 calories/cm.sup.2 or less is capable of releasing free radicals each having a molecular weight between 1 and 120. Exemplary donor additives are dibasic acids, polyamines and metal hydrides.

Close-in airblast from underground explosions

Energy Technology Data Exchange (ETDEWEB)

Vortman, L J [Sandia Laboratories, Albuquerque, NM (United States)

1970-05-15

Air overpressures as a function of time have been measured from surface zero to about 170 ft/lb{sup 1/3} along the ground from nuclear and chemical explosions. Charge depths varied from the surface to depths below which explosion gases are contained. A ground-shock-induced air pressure pulse is clearly distinguishable from the pulse caused by venting gases. Measured peak overpressures show reasonable agreement with the theoretical treatment by Monta. In a given medium the suppression of blast with explosion burial depth is a function of the relative distance at which the blast is observed. Rates of suppression of peak overpressure with charge burial are different for the two pulses. Rates are determined for each pulse over the range of distances at which measurements have been made of air overpressure from chemical explosions in several media. Nuclear data are available from too few shots for similar dependence on burial depth and distance to be developed, but it is clear that the gas venting peak overpressure from nuclear explosions is much more dependent on medium than that from chemical explosions. For above-ground explosions, experiment has shown that airblast from a I-kiloton nuclear explosion is equal to that from a 0.5-kiloton TNT explosion. Data on ground-shock-induced airblast is now sufficient to show that a similar relationship may exist for buried explosions. Because of medium dependence of the gas venting pulse from nuclear explosions, data from additional nuclear events will be required before a chemical/nuclear airblast equivalence can be determined for the gas-venting pulse. (author)

Dyadic violence and readiness to change among male intimate partner violence offenders.

Science.gov (United States)

Crane, Cory A; Schlauch, Robert C; Eckhardt, Christopher I

2015-12-10

Although readiness to change is associated with mandated partner violence treatment compliance and subsequent violent behaviour among male offenders (e.g. Scott and Wolfe, 2003; Eckhardt et al., 2004), our understanding of the factors associated with pretreatment change remains limited. Offender research indicates that individual and dyadic violent behaviour are highly variable and that such variability may provide insight into levels of pretreatment change (Holtzworth-Munroe and Stuart, 1994; Archer, 2002). We sought to examine the associations between indicators of change and individual as well as dyadic violence frequency in a sample of male partner violence offenders. To determine whether severity and perceived concordance in the use of violence among male offenders and their female partners influenced readiness to change at pretreatment, 82 recently adjudicated male perpetrators of intimate partner violence were recruited into the current study and administered measures of readiness to change violent behaviour (Revised Safe at Home Scale; Begun et al., 2008) as well as partner violence experiences (Revised Conflict Tactics Scale; Straus et al., 1996). Analyses revealed an interaction between offender-reported male and female violence in the prediction of pretreatment readiness to change such that greater male violence was associated with greater readiness to change among males who reported that their female partners perpetrated low, but not high, levels of violence. Consistently, greater female violence was associated with lower readiness to change only among the most violent male offenders. Results provide support for the assertion that the most violent offenders may be the most resistant to partner violence intervention efforts, particularly when they perceive themselves to be victims as well. Enhanced motivational and couples programming may facilitate treatment engagement among the high-risk group of male offenders who report concordant relationship

Gaming Against Violence: A Grassroots Approach to Teen Dating Violence.

Science.gov (United States)

Crecente, Drew

2014-08-01

Teen dating violence is a pervasive problem that affects millions of adolescents worldwide. Although there have been various approaches to addressing this problem, using videogames had not been employed before 2008, when Jennifer Ann's Group, an Atlanta, GA-based nonprofit organization, created an annual competition. The Life.Love. Game Design Challenge rewards game developers for creating videogames about teen dating violence without using any violence in the games themselves. The resulting videogames have increased awareness about teen dating violence and provided educational information to assist adolescents, parents, and teachers in identifying abusive relationships.

Primary Prevention of Violence: Stopping Campus Violence before It Starts. Prevention Update

Science.gov (United States)

Higher Education Center for Alcohol, Drug Abuse, and Violence Prevention, 2010

2010-01-01

Violence is a serious problem on college campuses. The literature on primary prevention of violence does not call for the adoption of specific programs or policies but rather suggests a paradigm shift in the way practitioners approach violence. Primary prevention means asking the question, "Why is violence happening in the first place?" in order…

Youth violence: An update

Directory of Open Access Journals (Sweden)

John Leonardo Díaz Galvis

2004-08-01

Full Text Available In this article we try to summarize the principal concepts around the biological and psychological contributions that explain the juvenile violence. In the genetic part we talk about adoption, twins studies and the genes that had been related with violence. In the area of neurotransmitters we selective talk about serotonine. We outline the relationship between sexual y physical abuse with violence and the link of those that consume alcohol and drugs with violence conducts. We also briefly view the roll of TV and radio with juvenile violence. Finally the article describes the different kinds of treatment of violence.

Structural Changes of Lignin from Wheat Straw by Steam Explosion and Ethanol Pretreatments

Directory of Open Access Journals (Sweden)

Cheng Pan

2016-06-01

Full Text Available Effects of the pretreatment of wheat straw by steam explosion and ethanol were evaluated relative to the structural changes of lignin from the pretreated pulp. The lignin from steam explosion pulp (LS, lignin from steam blasting residual liquid (LL, lignin from ethanol pretreatment pulp (LE, lignin from black liquor (LB, and lignin from wheat straw (LW were separated, and the structural characteristics of the lignin fractions were compared based on analyses of Fourier transform-infrared, ultraviolet, thermogravimetric, and 1H and 13C nuclear magnetic resonance spectra. The proportions of the three structural units in all lignin fractions clearly changed during the pretreatment process because of inter-conversion reactions. The conjugated structure of lignin was destroyed in the pretreatment process and was also affected by the alkali extraction process. The alcoholic hydroxyl links on the aliphatic side chain were partly transformed into carbonyl groups during ethanol pretreatment. Demethoxylation occurred in all lignin fractions during the ethanol pretreatment and steam explosion process. The thermal stability of the LB fraction was relatively high because of the condensation reaction.

8. Peaceful uses of nuclear explosions

International Nuclear Information System (INIS)

Musilek, L.

1992-01-01

The chapter deals with peaceful uses of nuclear explosions. Described are the development of the underground nuclear explosion, properties of radionuclides formed during the explosion, their distribution, the release of radioactive products of underground nuclear explosions into the air, their propagation in the atmosphere, and fallout in the landscape. (Z.S.). 1 tab., 8 figs., 19 refs

Heavy alcohol use and dating violence perpetration during adolescence: family, peer and neighborhood violence as moderators.

Science.gov (United States)

McNaughton Reyes, Heathe Luz; Foshee, Vangie A; Bauer, Daniel J; Ennett, Susan T

2012-08-01

We examined the hypothesis that family, peer and neighborhood violence would moderate relations between heavy alcohol use and adolescent dating violence perpetration such that relations would be stronger for teens in violent contexts. Random coefficients growth models were used to examine the main and interaction effects of heavy alcohol use and four measures of violence (family violence, friend dating violence, friend peer violence and neighborhood violence) on levels of physical dating violence perpetration across grades 8 through 12. The effects of heavy alcohol use on dating violence tended to diminish over time and were stronger in the spring than in the fall semesters. Consistent with hypotheses, across all grades, relations between heavy alcohol use and dating violence were stronger for teens exposed to higher levels of family violence and friend dating violence. However, neither friend peer violence nor neighborhood violence moderated relations between alcohol use and dating violence. Taken together, findings suggest that as adolescents grow older, individual and contextual moderators may play an increasingly important role in explaining individual differences in relations between alcohol use and dating violence. Implications for the design and evaluation of dating abuse prevention programs are discussed.

Heavy Alcohol Use and Dating Violence Perpetration During Adolescence: Family, Peer and Neighborhood Violence as Moderators

Science.gov (United States)

Foshee, Vangie A.; Bauer, Daniel J.; Ennett, Susan T.

2014-01-01

We examined the hypothesis that family, peer and neighborhood violence would moderate relations between heavy alcohol use and adolescent dating violence perpetration such that relations would be stronger for teens in violent contexts. Random coefficients growth models were used to examine the main and interaction effects of heavy alcohol use and four measures of violence (family violence, friend dating violence, friend peer violence and neighborhood violence) on levels of physical dating violence perpetration across grades 8 through 12. The effects of heavy alcohol use on dating violence tended to diminish over time and were stronger in the spring than in the fall semesters. Consistent with hypotheses, across all grades, relations between heavy alcohol use and dating violence were stronger for teens exposed to higher levels of family violence and friend dating violence. However, neither friend peer violence nor neighborhood violence moderated relations between alcohol use and dating violence. Taken together, findings suggest that as adolescents grow older, individual and contextual moderators may play an increasingly important role in explaining individual differences in relations between alcohol use and dating violence. Implications for the design and evaluation of dating abuse prevention programs are discussed. PMID:21494801

Violence against women.

Science.gov (United States)

Shiva, M

1999-01-01

In India, violence against women is increasing and takes many forms while laws to protect women are ignored. Despite this fact, the new reproductive and child health program ignores sexual violence. Health personnel can respond by: 1) accepting the magnitude of the problem; 2) investigating the deaths of young women; 3) documenting findings; 4) ensuring that sexual abuse is recognized as a public health problem; 5) disseminating findings; 6) ensuring the protection of female field workers; 7) recognizing violence as an occupational health hazard; 8) facilitating the empowerment of women; 9) training women in self-defense; 10) ensuring that colleges and training institutes address violence as a women's health concern; 11) studying the psychological effects of violence; 12) collaborating with the National Commission for Women and the National Human Rights Commission; and 13) advocating for incorporation of sexual violence as a reproductive health issue in the national reproductive health program. In particular, domestic violence is a pervasive violation of women's human rights and has been resistant to social advances because of its "hidden" nature. Domestic violence exists because husbands believe they have an absolute right over the sexuality of their wives. Abusive husbands also abuse their daughters while sons learn violent behavior from their fathers. Crimes must be considered irrespective of whether they are committed outside or inside the home.

27 CFR 70.445 - Commerce in explosives.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Commerce in explosives. 70... Cartridges, and Explosives § 70.445 Commerce in explosives. Part 55 of title 27 CFR contains the regulations..., explosives, (b) Permits for users who buy or transport explosives in interstate or foreign commerce, (c...

Simulation of the chemical environment of a nuclear explosion with exploding wires

Energy Technology Data Exchange (ETDEWEB)

Meyer, Walter; Block, Oliver U.J. [Nuclear Engineering, Kansas State University, Manhattan, KS (United States)

1970-05-15

The chemical processes in an expanding underground cavity resulting from a nuclear explosion cannot be predicted or controlled as well as such physical characteristics as crater size, magnitude of the outgoing shock wave, or the extent of rock fracturing. However in most underground nuclear explosions it would be desirable to control the chemical and/or physical form and amount of radioactive fallout venting from the explosion. The high temperatures and corresponding high energy densities produced by exploding wires are sufficient to produce in the wire and material immediately surrounding it the temperature (a few thousand degrees) required to simulate the chemical environment of a nuclear explosion in the time interval just preceding the venting of the cavity. The economics and the size of exploding wire apparatus make this type of experiment readily applicable to laboratory study. Design of exploding wire circuits to obtain particular temperatures or energy densities can be completed using several different combinations of circuit and wire conditions. Since the circuit parameters, including charging voltage, capacitor bank capacitance and circuit inductance primarily determine the cost of the necessary laboratory equipment, these parameters should be selected by theoretical expressions while also considering economic factors. Wire parameters are then experimentally determined to produce the most energetic explosions with the selected circuit parameters. A theoretical method applicable to designing exploding wire circuits to produce the desired high temperatures and energy densities in the wire and surrounding sample material has been obtained. The method assumes that a thermal spike of energy is deposited in a low conductivity material (typical of the earth's crust) surrounding the wire. From the assumed temperature distribution in the surrounding sample material the energy which must be deposited in the thermal spike to produce the desired temperature and

Idaho Explosives Detection System

International Nuclear Information System (INIS)

Reber, Edward L.; Blackwood, Larry G.; Edwards, Andrew J.; Jewell, J. Keith; Rohde, Kenneth W.; Seabury, Edward H.; Klinger, Jeffery B.

2005-01-01

The Idaho Explosives Detection System was developed at the Idaho National Laboratory (INL) to respond to threats imposed by delivery trucks potentially carrying explosives into military bases. A full-scale prototype system has been built and is currently undergoing testing. The system consists of two racks, one on each side of a subject vehicle. Each rack includes a neutron generator and an array of NaI detectors. The two neutron generators are pulsed and synchronized. A laptop computer controls the entire system. The control software is easily operable by minimally trained staff. The system was developed to detect explosives in a medium size truck within a 5-min measurement time. System performance was successfully demonstrated with explosives at the INL in June 2004 and at Andrews Air Force Base in July 2004

Idaho Explosives Detection System

Energy Technology Data Exchange (ETDEWEB)

Reber, Edward L. [Idaho National Laboratory, 2525 N. Freemont Ave., Idaho Falls, ID 83415-2114 (United States)]. E-mail: reber@inel.gov; Blackwood, Larry G. [Idaho National Laboratory, 2525 N. Freemont Ave., Idaho Falls, ID 83415-2114 (United States); Edwards, Andrew J. [Idaho National Laboratory, 2525 N. Freemont Ave., Idaho Falls, ID 83415-2114 (United States); Jewell, J. Keith [Idaho National Laboratory, 2525 N. Freemont Ave., Idaho Falls, ID 83415-2114 (United States); Rohde, Kenneth W. [Idaho National Laboratory, 2525 N. Freemont Ave., Idaho Falls, ID 83415-2114 (United States); Seabury, Edward H. [Idaho National Laboratory, 2525 N. Freemont Ave., Idaho Falls, ID 83415-2114 (United States); Klinger, Jeffery B. [Idaho National Laboratory, 2525 N. Freemont Ave., Idaho Falls, ID 83415-2114 (United States)

2005-12-15

The Idaho Explosives Detection System was developed at the Idaho National Laboratory (INL) to respond to threats imposed by delivery trucks potentially carrying explosives into military bases. A full-scale prototype system has been built and is currently undergoing testing. The system consists of two racks, one on each side of a subject vehicle. Each rack includes a neutron generator and an array of NaI detectors. The two neutron generators are pulsed and synchronized. A laptop computer controls the entire system. The control software is easily operable by minimally trained staff. The system was developed to detect explosives in a medium size truck within a 5-min measurement time. System performance was successfully demonstrated with explosives at the INL in June 2004 and at Andrews Air Force Base in July 2004.

Trace explosives sensor testbed (TESTbed)

Science.gov (United States)

Collins, Greg E.; Malito, Michael P.; Tamanaha, Cy R.; Hammond, Mark H.; Giordano, Braden C.; Lubrano, Adam L.; Field, Christopher R.; Rogers, Duane A.; Jeffries, Russell A.; Colton, Richard J.; Rose-Pehrsson, Susan L.

2017-03-01

A novel vapor delivery testbed, referred to as the Trace Explosives Sensor Testbed, or TESTbed, is demonstrated that is amenable to both high- and low-volatility explosives vapors including nitromethane, nitroglycerine, ethylene glycol dinitrate, triacetone triperoxide, 2,4,6-trinitrotoluene, pentaerythritol tetranitrate, and hexahydro-1,3,5-trinitro-1,3,5-triazine. The TESTbed incorporates a six-port dual-line manifold system allowing for rapid actuation between a dedicated clean air source and a trace explosives vapor source. Explosives and explosives-related vapors can be sourced through a number of means including gas cylinders, permeation tube ovens, dynamic headspace chambers, and a Pneumatically Modulated Liquid Delivery System coupled to a perfluoroalkoxy total-consumption microflow nebulizer. Key features of the TESTbed include continuous and pulseless control of trace vapor concentrations with wide dynamic range of concentration generation, six sampling ports with reproducible vapor profile outputs, limited low-volatility explosives adsorption to the manifold surface, temperature and humidity control of the vapor stream, and a graphical user interface for system operation and testing protocol implementation.

Improving the Material Response for Slow Heat of Energetic Materials

Energy Technology Data Exchange (ETDEWEB)

Nichols, A L

2010-03-08

The goal of modern high explosive slow heat cookoff modeling is to understand the level of mechanical violence. This requires understanding the coupled thermal-mechanical-chemical system that such an environment creates. Recent advances have improved our ability to predict the time to event, and we have been making progress on predicting the mechanical response. By adding surface tension to the product gas pores in the high explosive, we have been able to reduce the current model's tendency to overpressurize confinement vessels. We describe the model and demonstrate how it affects a LX-10 STEX experiment. Issues associated with current product gas equations of state are described and examined.

Report on the treatability study for inerting small quantities of radioactive explosives and explosive components

International Nuclear Information System (INIS)

Loyola, V.M.; Reber, S.D.

1996-02-01

As a result of Sandia's radiation hardening testing on a variety of its explosive components, radioactive waste streams were generated and have to be disposed of as radioactive waste. Due to the combined hazards of explosives and radioactivity, Sandia's Radioactive and Mixed Waste Management organization did not have a mechanism for disposal of these waste streams. This report documents the study done to provide a method for the removal of the explosive hazard from those waste streams. The report includes the design of the equipment used, procedures followed, results from waste stream analog tests and the results from the actual explosive inerting tests on radioactive samples. As a result of the inerting treatment, the waste streams were rendered non-explosive and, thus, manageable through normal radioactive waste disposal channels

Know Your Rights: Domestic Violence

Science.gov (United States)

... 3224 TTD You CAN do something about domestic violence Domestic violence is a pattern of many behaviors directed ... violence. Look in the Yellow Pages under “domestic violence help,” “domestic violence shelters,” “human services organizations,” or “crisis intervention” ...

Mainstreaming domestic and gender-based violence into sociology and the criminology of violence

OpenAIRE

Walby, Sylvia; Towers, Jude; Francis, Brian

2014-01-01

Sociological and criminological views of domestic and gender-based violence generally either dismiss it as not worthy of consideration, or focus on specific groups of offenders and victims (male youth gangs, partner violence victims). In this paper, we take a holistic approach to violence, extending the definition from that commonly in use to encompass domestic violence and sexual violence. We operationalize that definition by using data from the latest sweep of the Crime Survey for England a...

R-22 vapor explosions

International Nuclear Information System (INIS)

Anderson, R.P.; Armstrong, D.R.

1977-01-01

Previous experimental and theoretical studies of R-22 vapor explosions are reviewed. Results from two experimental investigations of vapor explosions in a medium scale R-22/water system are reported. Measurements following the drop of an unrestrained mass of R-22 into a water tank demonstrated the existence of two types of interaction behavior. Release of a constrained mass of R-22 beneath the surface of a water tank improved the visual resolution of the system thus allowing identification of two interaction mechansims: at low water temperatures, R-22/water contact would produce immediate violent boiling; at high water temperatures a vapor film formed around its R-22 as it was released, explosions were generated by a surface wave which initiated at a single location and propagated along the vapor film as a shock wave. A new vapor explosion model is proposed, it suggests explosions are the result of a sequence of three independent steps: an initial mixing phase, a trigger and growth phase, and a mature phase where a propagating shock wave accelerates the two liquids into a collapsing vapor layer causing a high velocity impact which finely fragments and intermixes the two liquids

Unreported workplace violence in nursing.

Science.gov (United States)

Kvas, A; Seljak, J

2014-09-01

Workplace violence occurs on a frequent basis in nursing. Most violent acts remain unreported. Consequently, we do not know the actual frequency of the occurrence of workplace violence. This requires research of nurses' actions following workplace violence and identification of reasons why most victims do not report violent acts in the appropriate manner. To explore violence in nursing as experienced by nurses in Slovenia. A survey was carried out with a representative sample of nurses in Slovenia. The questionnaire Workplace Violence in Nursing was submitted to 3756 nurses, with 692 completing the questionnaire. A total of 61.6% of the nurses surveyed had been exposed to violence in the past year. Most victims were exposed to psychological (60.1%) and economic violence (28.9%). Victims reported acts of violence in formal written form in a range from 6.5% (psychological violence) to 10.9% (physical violence). The largest share of victims who did not report violence and did not speak to anyone about it were victims of sexual violence (17.9%). The main reason for not reporting the violence was the belief that reporting it would not change anything, followed by the fear of losing one's job. Only a small share of the respondents reported violence in written form, the main reason being the victims' belief that reporting it would not change anything. This represents a severe criticism of the system for preventing workplace violence for it reveals the failure of response by leadership structures in healthcare organizations. Professional associations and the education system must prepare nurses for the prevention of violence and appropriate actions in the event of violent acts. Healthcare organizations must ensure the necessary conditions for enabling and encouraging appropriate actions following violent acts according to relevant protocols. © 2014 International Council of Nurses.

A review of steam explosions with special emphasis on the Swedish and Finnish BWRs. APRI 4, Phase 2 Report

Energy Technology Data Exchange (ETDEWEB)

Sehgal, B.R.; Haraldsson, H.O.; Yang, Z.L. [Sehgal Konsult, Stockholm (Sweden)

2002-04-01

The objective of the present study is to perform a critical review of ex-vessel steam explosion in Swedish and Finnish reactor containments in a hypothetical severe accident. The review performed is related to a broader program funded by APRI whose focus is related to severe accidents. A critical review of the current knowledge base on the subject is performed, including those results obtained from other studies and assessments conducted earlier under auspice of APRI. Several limiting mechanisms which may significantly impact the assessment of steam explosion loads are identified, taking into account specific reactor-design features and accident progression scenarios. In addition, generic discussion is provided on the effect of melt physical properties on the steam explosion energetics. Thermal hydraulic conditions of pre-mixture and its explosivity are evaluated using models and methods developed by the researchers at Royal Institute of Technology (RIT). The report includes a wealth of information on details with respect to quantification of vessel melt sources for ex-vessel FCIs; and with respect to the models of steam explosion premixing, triggerability and explosivity employed in the present assessment. These and other models e.g. on vessel failure, melt jet fragmentation etc. are products of the continuing research conducted at the Division of Nuclear Power Safety at RIT. The general conclusion of the present study can be summarized as: Though substantial progress have been made in premixing research verifying the mixing limit concept, there is still a need to improve jet breakup models and validate the existing models against melt jet experiments. The understanding of the triggering mechanisms is still very pool. Though various analytical models have been developed based on the thermal detonation concepts, the need still exists in both experimental and analytical research to understand better the droplet fragmentation during the explosion or propagation phase

A review of steam explosions with special emphasis on the Swedish and Finnish BWRs. APRI 4, Phase 2 Report

International Nuclear Information System (INIS)

Sehgal, B.R.; Haraldsson, H.O.; Yang, Z.L.

2002-04-01

The objective of the present study is to perform a critical review of ex-vessel steam explosion in Swedish and Finnish reactor containments in a hypothetical severe accident. The review performed is related to a broader program funded by APRI whose focus is related to severe accidents. A critical review of the current knowledge base on the subject is performed, including those results obtained from other studies and assessments conducted earlier under auspice of APRI. Several limiting mechanisms which may significantly impact the assessment of steam explosion loads are identified, taking into account specific reactor-design features and accident progression scenarios. In addition, generic discussion is provided on the effect of melt physical properties on the steam explosion energetics. Thermal hydraulic conditions of pre-mixture and its explosivity are evaluated using models and methods developed by the researchers at Royal Institute of Technology (RIT). The report includes a wealth of information on details with respect to quantification of vessel melt sources for ex-vessel FCIs; and with respect to the models of steam explosion premixing, triggerability and explosivity employed in the present assessment. These and other models e.g. on vessel failure, melt jet fragmentation etc. are products of the continuing research conducted at the Division of Nuclear Power Safety at RIT. The general conclusion of the present study can be summarized as: Though substantial progress have been made in premixing research verifying the mixing limit concept, there is still a need to improve jet breakup models and validate the existing models against melt jet experiments. The understanding of the triggering mechanisms is still very pool. Though various analytical models have been developed based on the thermal detonation concepts, the need still exists in both experimental and analytical research to understand better the droplet fragmentation during the explosion or propagation phase

Parametric Explosion Spectral Model

Energy Technology Data Exchange (ETDEWEB)

Ford, S R; Walter, W R

2012-01-19

Small underground nuclear explosions need to be confidently detected, identified, and characterized in regions of the world where they have never before occurred. We develop a parametric model of the nuclear explosion seismic source spectrum derived from regional phases that is compatible with earthquake-based geometrical spreading and attenuation. Earthquake spectra are fit with a generalized version of the Brune spectrum, which is a three-parameter model that describes the long-period level, corner-frequency, and spectral slope at high-frequencies. Explosion spectra can be fit with similar spectral models whose parameters are then correlated with near-source geology and containment conditions. We observe a correlation of high gas-porosity (low-strength) with increased spectral slope. The relationship between the parametric equations and the geologic and containment conditions will assist in our physical understanding of the nuclear explosion source.

Expediency of application of explosion-relief constructions to ensure explosion resistance of production buildings

Directory of Open Access Journals (Sweden)

Lyapin Anton

2016-01-01

Full Text Available The article presents a model of economic evaluation and selection of explosion-relief constructions (ERC, as well as determination of explosion protection efficiency of buildings and structures provided on a stage of construction. It has been shown that definition of economic efficiency of ERС is the evaluation of its application for buildings with remote or automatically controlled production. It has been determined that an important role in design of explosive industrial facilities is played by selection of the economically feasible and effective materials for ERC. When selecting materials it is necessary to consider probability and yield of explosions. Necessity to create the methods allow considering such probability has been revealed.

Broadening the Perspective on Gun Violence: An Examination of the Firearms Industry, 1990-2015.

Science.gov (United States)

Smith, Victoria M; Siegel, Michael; Xuan, Ziming; Ross, Craig S; Galea, Sandro; Kalesan, Bindu; Fleegler, Eric; Goss, Kristin A

2017-11-01

Firearm violence injures or kills 100,000 Americans each year. This paper applies the Host-Agent-Vector-Environment model to this issue. Research on firearm violence tends to focus on two elements-the host (i.e., victims of firearm violence) and the environment (i.e., gun policies)-but little attention has been paid to the agent (the gun and ammunition) or the vector (firearm manufacturers, dealers, and the industry lobby). Using Bureau of Alcohol, Tobacco, Firearms and Explosives data, trends in firearm manufacturing were investigated from 1990 to 2015. Outcome measures included: (1) trends in domestic gun manufacturing by weapon type; (2) trends in production by firearm caliber; and (3) 2015 market share by type of firearm and company. Data were collected and analyzed in 2016. Overall domestic firearms production decreased slightly from 1996 through 2004, and then steadily increased from 1.7% in 2005 to 13.8% in 2013, when >10 million firearms were produced for the domestic market. The increase in total firearm production was driven by the increased production of pistols and rifles. Within the pistol category, increased production was attributable to an increase in higher caliber weapons. Similar trends were observed in gun purchases and recovered and traced crime guns. Trends in firearm manufacturing reveal a shift toward more-lethal weapons, and this trend is also observed in gun purchases and crime gun traces. This may reflect a societal shift in cultural practices and norms related to guns and could inform strategies to reduce firearm violence. Copyright © 2017 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Workplace Violence

Science.gov (United States)

... to reduce workplace violence. Management Commitment: Provides the motivation and resources to deal effectively with workplace violence ... physical health of the employee. Appropriate allocation of authority and resources to responsible parties. Equal commitment to ...

Explosives 92. Conference proceedings

Energy Technology Data Exchange (ETDEWEB)

Farnfield, R.A. (ed.)

1992-01-01

17 papers are presented. Topics covered include: the POG system - a new concept in the use of ANFO; demolition of a motorway bridge; presplit and smooth blasting; VIBReX - a predictive code for assessing the effect of blast design on ground vibration; ground vibrations from blasting; digital seismographs; human response to blasting and the effects on planning conditions; landform construction by restoration blasting; use of small diameter explosives; efficient priming; safety management in the explosives industry; and the law on packaging of explosives. Two papers have been abstracted separately.

Research of thermal stability of ion exchangers

International Nuclear Information System (INIS)

Stuchlik, S.; Srnkova, J.

1983-01-01

Prior to the fixation of radioactive ion exchangers into bitumen these exchangers have to be dried. The resulting gaseous products may generate explosive mixtures. An analysis was made of the thermal stability of two types of ion exchangers, the cation exchanger KU-2-8 cS and the anion exchanger AV-17-8 cS which are used in the V-1 nuclear power plant at Jaslovske Bohunice. The thermal stability of the anion exchangers was monitored using gas chromatography at temperatures of 100, 120, 140, 160 and 180 degC and by measuring weight loss by kiln-drying at temperatures of 120, 140, 160 and 180 degC. The ion exchanger was heated for 6 hours and samples were taken continuously at one hour intervals. The thermal stability of the cation exchanger was monitored by measuring the weight loss. Gas chromatography showed the release of trimethylamine from the anion exchanger in direct dependence on temperature. The measurement of weight losses, however, only showed higher losses of released products which are explained by the release of other thermally unstable products. The analysis of the thermal stability of the cation exchanger showed the release of SO 2 and the weight loss (following correction for water content) was found only after the fourth hour of decomposition. The experiment showed that the drying of anion exchanger AV-17-8 cS may cause the formation of explosive mixtures. (J.P.)

Problems in the theory of point explosions

Science.gov (United States)

Korobeinikov, V. P.

The book is concerned with the development of the theory of point explosions, which is relevant to the study of such phenomena as the initiation of detonation, high-power explosions, electric discharges, cosmic explosions, laser blasts, and hypersonic aerodynamics. The discussion covers the principal equations and the statement of problems; linearized non-self-similar one-dimensional problems; spherical, cylindrical, and plane explosions with allowance for counterpressure under conditions of constant initial density; explosions in a combustible mixture of gases; and point explosions in inhomogeneous media with nonsymmetric energy release. Attention is also given to point explosions in an electrically conducting gas with allowance for the effect of the magnetic field and to the propagation of perturbations from solar flares.

Alternatives to Violence.

Science.gov (United States)

Children Today, 1994

1994-01-01

Notes that our capacity to diffuse conflict rests in our ability to recognize and verbalize feelings, develop empathy, and think of alternatives to violence. Explores the influence of role models and culture on violence and how the media can use violent images effectively in helping us confront a culture of violence. (HTH)

Effectiveness of laser sources for contactless sampling of explosives

Science.gov (United States)

Akmalov, Artem E.; Chistyakov, Alexander A.; Kotkovskii, Gennadii E.

2016-05-01

A mass-spectrometric study of photo processes initiated by ultraviolet (UV) laser radiation in explosives adsorbed on metal and dielectric substrates has been performed. A calibrated quadrupole mass spectrometer was used to determine a value of activation energy of desorption and a quantity of explosives desorbed by laser radiation. A special vacuumoptical module was elaborated and integrated into a vacuum mass-spectrometric system to focus the laser beam on a sample. It has been shown that the action of nanosecond laser radiation set at q= 107 - 108 W/cm2, λ=266 nm on adsorbed layers of molecules of trinitrotoluene (TNT ) and pentaerytritoltetranitrate (PETN) leads not only to an effective desorption, but also to the non-equilibrium dissociation of molecules with the formation of nitrogen oxide NO. The cyclotrimethylenetrinitramine (RDX) dissociation products are observed only at high laser intensities (q> 109 W/cm2) thus indicating the thermal nature of dissociation, whereas desorption of RDX is observed even at q> 107 W/cm2 from all substrates. Desorption is not observed for cyclotetramethylenetetranitramine (HMX) under single pulse action: the dissociation products NO and NO2 are registered only, whereas irradiation at 10Hz is quite effective for HMX desorption. The results clearly demonstrate a high efficiency of nanosecond laser radiation with λ = 266 nm, q ~ 107 - 108 W/cm2, Epulse= 1mJ for desorption of molecules of explosives from various surfaces.

Workplace physical violence, verbal violence, and mobbing experienced by nurses at a university hospital.

Science.gov (United States)

Aksakal, Fatma Nur Baran; Karaşahin, Emine Füsun; Dikmen, Asiye Uğraş; Avci, Emine; Ozkan, Seçil

2015-01-01

The aim of this study was to determine the frequency of and risk factors for physical violence, verbal violence, and mobbing experienced by nurses in a university hospital. This was a cross-sectional study conducted at Gazi University Medical Faculty Hospital. A questionnaire form recommended by the WHO and the International Labor Organization was administered through face-to-face interviews to determine the violence experienced in the past 12 months by nurses. The prevalence of physical violence, verbal violence, and mobbing was 13.9%, 41.8%, and 17.1%, respectively. Working more than 40 h per week increased the risk of physical violence by 1.86 times. The majority of nurses who experienced verbal violence and mobbing were significantly more willing to change their work, their institution, and their profession if given the opportunity. Fewer than one-fourth of the victims indicated they reported any incident. We knew that the prevalence of physical violence, verbal violence, and mobbing were high among nurses and that incidents were underreported, and the study corroborated this information. What this study adds to the topic is that long working hours increased the prevalence of physical violence and was defined as an important contributory factor.

Exposure to violence, typology, and recidivism in a probation sample of domestic violence perpetrators.

Science.gov (United States)

Fowler, Drew R; Cantos, Arthur L; Miller, Steven A

2016-09-01

The present study investigated the predictive utility of self-reported domestic violence perpetrators' exposure to violence in their family of origin and patterns related to this exposure through the use of longitudinal analyses on a sample of 228 men on probation in Lake County, Illinois. Differences in typology, recidivism, recidivism frequency, and violent behavior survival patterns in men with a history of domestic violence perpetration and with varying levels of family of origin violence exposure were examined. Findings suggest that those who witnessed interparental violence (either alone, or in combination with experiencing violence) were most likely to be classified as Generally Violent offenders (e.g., perpetrators who direct violence toward their family and others), compared to those who did not report experiencing or witnessing violence. In addition, results also indicate that men who experienced both witnessing interparental violence and receiving physical abuse in childhood were more likely to recidivate more frequently compared to those who did not report experiencing or witnessing violence. No significant findings for typology and recidivism were noted. Clinical and policy/practice implications are discussed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Search for evidence of nuclear involvement in the fatal explosion of a 'cold fusion' experiment

International Nuclear Information System (INIS)

Grant, P.M.; Whipple, R.E.; Andresen, B.D.; Russo, R.E.; Bazan, F.; Brunk, J.L.; Wong, K.M.

1995-01-01

Forensic analyses of debris from the fatal explosion of an electrochemical 'cold fusion' cell at SRI International were conducted at LLNL at the request of Cal-OSHA. One investigation focused on the possibility of conventional nuclear reaction mechanisms contributing to the total energy inventory of the incident. Selected metal components of the electrolysis apparatus were subjected to nondestructive γ-ray spectrometry with high-sensitivity, low-background Ge detector systems. The anticipated analytes in these studies were radioactivation products potentially induced in the explosion residue by either fast or thermal neutrons. The results of this investigation were negative within the temporal constraints of the incident and the analytical sensitivities of the instrumentation. (author) 5 refs.; 1 fig.; 2 tabs

Detection of trace explosives on relevant substrates using a mobile platform for photothermal infrared imaging spectroscopy (PT-IRIS)

Science.gov (United States)

Kendziora, Christopher A.; Furstenberg, Robert; Papantonakis, Michael; Nguyen, Viet; Byers, Jeff; McGill, R. Andrew

2015-05-01

This manuscript describes the results of recent tests regarding standoff detection of trace explosives on relevant substrates using a mobile platform. We are developing a technology for detection based on photo-thermal infrared (IR) imaging spectroscopy (PT-IRIS). This approach leverages one or more microfabricated IR quantum cascade lasers, tuned to strong absorption bands in the analytes and directed to illuminate an area on a surface of interest. An IR focal plane array is used to image the surface thermal emission upon laser illumination. The PT-IRIS signal is processed as a hyperspectral image cube comprised of spatial, spectral and temporal dimensions as vectors within a detection algorithm. Increased sensitivity to explosives and selectivity between different analyte types is achieved by narrow bandpass IR filters in the collection path. We have previously demonstrated the technique at several meters of stand-off distance indoors and in field tests, while operating the lasers below the infrared eye-safe intensity limit (100 mW/cm2). Sensitivity to explosive traces as small as a single 10 μm diameter particle (~1 ng) has been demonstrated. Analytes tested here include RDX, TNT, ammonium nitrate and sucrose. The substrates tested in this current work include metal, plastics, glass and painted car panels.

From violence to more violence in Central America

Directory of Open Access Journals (Sweden)

Israel Medina

2014-11-01

Full Text Available Many Central American migrants flee their home country as a result of violence and threats from the criminal gangs. A large number of them also encounter the same type of violence that they are fleeing when on the migratory routes through Mexico.

Teen Violence

Science.gov (United States)

Teen violence refers to harmful behaviors that can start early and continue into young adulthood. The young person can ... victim, an offender, or a witness to the violence. Violent acts can include Bullying Fighting, including punching, ...

Safety engineering experiments of explosives

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, Noboru

1987-07-24

The outline of large scale experiments carried out every year since 1969 to obtain fundamental data and then establish the safety engineering standards concerning the manufacturing, storage and transportation, etc. of all explosives was described. Because it becomes recently difficult to ensure the safety distance in powder magazines and powder plants, the sandwich structure with sand is thought to be suitable as the neighboring barrier walls. The special vertical structure for embankments to provide against a emergency explosion is effective to absorb the blast. Explosion behaviors such as initiating sensitivity, detonation, sympathetic detonation, and shock occurence of the ANFO explosives in place of dynamite and the slurry explosives were studied. The safety engineering standards for the manufacturing and application of explosives were studied to establish because accidents by tabacco fire are not still distinguished. Much data concerning early stage fire fighting, a large quantity of flooding and shock occurence from a assumption of ignition during machining in the propellants manufacturing plant, could be obtained. Basic studies were made to prevent pollution in blasting sites. Collected data are utilized for the safety administration after sufficient discussion. (4 figs, 2 tabs, 3 photos, 17 refs)

The Relationship between Violence in the Family of Origin and Dating Violence among College Students

Science.gov (United States)

Gover, Angela R.; Kaukinen, Catherine; Fox, Kathleen A.

2008-01-01

Prior research has established that violence in dating relationships is a serious social problem among adolescents and young adults. Exposure to violence during childhood has been linked to dating violence victimization and perpetration. Also known as the intergenerational transmission of violence, the link between violence during childhood and…

Sensitivity to friction for primary explosives

International Nuclear Information System (INIS)

Matyáš, Robert; Šelešovský, Jakub; Musil, Tomáš

2012-01-01

Highlights: ► The friction sensitivity of 14 samples of primary explosives was determined. ► The same apparatus (small scale BAM) and the same method (probit analysis) was used. ► The crystal shapes and sizes were documented with microscopy. ► Almost all samples are less sensitive than lead azide, which is commercially used. ► The organic peroxides (TATP, DADP, HMTD) are not as sensitive as often reported. - Abstract: The sensitivity to friction for a selection of primary explosives has been studied using a small BAM friction apparatus. The probit analysis was used for the construction of a sensitivity curve for each primary explosive tested. Two groups of primary explosives were chosen for measurement (a) the most commonly used industrially produced primary explosives (e.g. lead azide, tetrazene, dinol, lead styphnate) and (b) the most produced improvised primary explosives (e.g. triacetone triperoxide, hexamethylenetriperoxide diamine, mercury fulminate, acetylides of heavy metals). A knowledge of friction sensitivity is very important for determining manipulation safety for primary explosives. All the primary explosives tested were carefully characterised (synthesis procedure, shape and size of crystals). The sensitivity curves obtained represent a unique set of data, which cannot be found anywhere else in the available literature.

Sensitivity to friction for primary explosives

Energy Technology Data Exchange (ETDEWEB)

Matyas, Robert, E-mail: robert.matyas@upce.cz [Institute of Energetic Materials, Faculty of Chemical Technology, University of Pardubice, Pardubice 532 10 (Czech Republic); Selesovsky, Jakub; Musil, Tomas [Institute of Energetic Materials, Faculty of Chemical Technology, University of Pardubice, Pardubice 532 10 (Czech Republic)

2012-04-30

Highlights: Black-Right-Pointing-Pointer The friction sensitivity of 14 samples of primary explosives was determined. Black-Right-Pointing-Pointer The same apparatus (small scale BAM) and the same method (probit analysis) was used. Black-Right-Pointing-Pointer The crystal shapes and sizes were documented with microscopy. Black-Right-Pointing-Pointer Almost all samples are less sensitive than lead azide, which is commercially used. Black-Right-Pointing-Pointer The organic peroxides (TATP, DADP, HMTD) are not as sensitive as often reported. - Abstract: The sensitivity to friction for a selection of primary explosives has been studied using a small BAM friction apparatus. The probit analysis was used for the construction of a sensitivity curve for each primary explosive tested. Two groups of primary explosives were chosen for measurement (a) the most commonly used industrially produced primary explosives (e.g. lead azide, tetrazene, dinol, lead styphnate) and (b) the most produced improvised primary explosives (e.g. triacetone triperoxide, hexamethylenetriperoxide diamine, mercury fulminate, acetylides of heavy metals). A knowledge of friction sensitivity is very important for determining manipulation safety for primary explosives. All the primary explosives tested were carefully characterised (synthesis procedure, shape and size of crystals). The sensitivity curves obtained represent a unique set of data, which cannot be found anywhere else in the available literature.

Violence as a Vicious Cycle

Directory of Open Access Journals (Sweden)

Huseyin Gulec

2012-03-01

Full Text Available Since the conclusion that the violence as a behavior is not (cannot be determined within an absolute genetic determinism has been reached for long years, environmental factors are increasingly examined. We witness that human behavior in society can easily convert into coping with stressful events with violence. Individual or social violence as a behavior has a similar pattern with violence committed in primitive society and by children. After a brief review of violence, its description, etiological theories and types, this article majorly focuses on children and their early and late response to violence. The purpose here is to draw attention to the individuals who were previously exposed to violence (either directly or indirectly resort to violence, perpetuating a vicious cycle.

Longitudinal relationships between individual and class norms supporting dating violence and perpetration of dating violence.

Science.gov (United States)

Taylor, Katherine A; Sullivan, Terri N; Farrell, Albert D

2015-03-01

Dating violence is commonly perpetrated in adolescence, making it imperative to understand risk factors in order to inform prevention efforts. Although individual norms supporting dating violence are strongly related to its perpetration, few studies have examined their longitudinal impact. Moreover, the influence of class norms (i.e., norms for students in the same grade, cohort, and school) supporting dating violence on perpetration has rarely been studied. The current study examined longitudinal relationships between individual and class norms supporting dating violence and perpetration of physical and psychological dating violence. Participants were two cohorts of sixth graders from 37 schools who were in dating relationships at Wave 1 and 6 months later at Wave 2 (N = 2,022; 43% female; 52% African American, 21% Latino/a, 20% White, and 7% other). The analyses used a multilevel approach, with students represented at Level 1 and classes (n = 74) at Level 2. The models tested direct effects of Wave 1 individual and class norms supporting dating violence on subsequent changes in perpetration of dating violence at Wave 2 and the extent to which gender moderated these relationships. The findings indicated that greater individual norms supporting male dating violence predicted greater change in perpetration of physical and psychological dating violence and greater individual norms supporting female dating violence predicted greater change in perpetration of psychological dating violence. Greater class norms supporting male dating violence predicted greater change in perpetration of physical dating violence; whereas greater class norms supporting female dating violence predicted less change in perpetration of physical dating violence. These findings highlight the need to address norms in early adolescence.

Sexual Violence

Science.gov (United States)

Sexual Violence Facts at a Glance 2012 Adults In a nationally representative survey of adults: 1 • Nearly 1 in ... 5.6% and 5.3%, respectively) experienced sexual violence other than rape, such as being made to ...

Healthcare Workers and Workplace Violence

Directory of Open Access Journals (Sweden)

Tevfik Pinar

2013-06-01

Full Text Available Workplace violence is a threatening worldwide public health problem. Healthcare workers have under particular risk of workplace violence, and they are being exposed to violence 4-16 times more than other service workers. The frequency of violence in the health sector in the world has indicated in different range of results since there is no consistent definition of workplace violence and differences in research methodology (any type of violence: 22,0% - 60,0%; physical violence: 2,6% - 57,0%; verbal violence: 24,3% - 82,0%; sexual harassment: %1,9 - 10,5%. All healthcare workers have right to work in a safe working place. The safety of healthcare workers should deserve the same priority as patient safety. Various risk factors including social, cultural, environmental, organizational and personal elements play a role in the formation of workplace violence that is very important for our country. Considering all those factors, the workplace violence in health sector should be seriously handled and the strategies and policies must be developed for prevention. [TAF Prev Med Bull 2013; 12(3.000: 315-326

Heavy Alcohol Use and Dating Violence Perpetration During Adolescence: Family, Peer and Neighborhood Violence as Moderators

OpenAIRE

McNaughton Reyes, Heathe Luz; Foshee, Vangie A.; Bauer, Daniel J.; Ennett, Susan T.

2012-01-01

We examined the hypothesis that family, peer and neighborhood violence would moderate relations between heavy alcohol use and adolescent dating violence perpetration such that relations would be stronger for teens in violent contexts. Random coefficients growth models were used to examine the main and interaction effects of heavy alcohol use and four measures of violence (family violence, friend dating violence, friend peer violence and neighborhood violence) on levels of physical dating viol...

Symbolic Violence and Gendered Sexualised Violence

DEFF Research Database (Denmark)

Pedersen, Bodil Maria

It has been suggested, that Bourdieu ´s concept of symbolic violence is useful in explaining gendered phenomena of late modern western societies, which can no longer simply be understood as classic patriarchies (B. Krais 1993). In these societies, and in spite of the existence of gendered...... sexualised phenomena such as rape and prostitution, it is often assumed that full equality of the sexes has been achieved. The concept of symbolic violence implies the participation of both men and women in aspects of discourses and other social practices related to gendering and thus to gendered sexualised...... violence. It deconstructs the dualisation of gender in gendered phenomena that contribute to the dualising/blaming controversies concerning responsibility and guilt common in discourses, activism and research pertaining to this field. Furthermore the use of the concept makes it possible to do so without...

VIOLENCE DRESSED IN HUMOR: COMEDIC VIOLENCE IN ADVERTISING

Directory of Open Access Journals (Sweden)

Camelia Gradinaru

2016-01-01

Full Text Available This paper investigates the concepts of humor and violence and their complex relationships contextualised in the advertising domain. Thus, the main theories of humor and the most important elements from media violence paradigms are critically pointed out. The effects of comedic violence in advertising may be positive (great involvement with the ad message, retention of brand information, higher pass-along probability, and also negative (offending the audience, desensitization, damaging the reputation and the brand equity. A lot of factors change the perception of comedic violent ads (gender, social norm beliefs etc., so that a multidimensional analysis of consumer perceptions is needed if we want to draw a more accurate picture of this phenomenon. The analysis of the specific ad that I developed in the second part of this paper showed clearly the interplay between perceived humor and perceived violence and also the relevance of the cultural background in its interpretation.

Short-term Lost Productivity per Victim: Intimate Partner Violence, Sexual Violence, or Stalking.

Science.gov (United States)

Peterson, Cora; Liu, Yang; Kresnow, Marcie-Jo; Florence, Curtis; Merrick, Melissa T; DeGue, Sarah; Lokey, Colby N

2018-05-15

The purpose of this study is to estimate victims' lifetime short-term lost productivity because of intimate partner violence, sexual violence, or stalking. U.S. nationally representative data from the 2012 National Intimate Partner and Sexual Violence Survey were used to estimate a regression-adjusted average per victim (female and male) and total population number of cumulative short-term lost work and school days (or lost productivity) because of victimizations over victims' lifetimes. Victims' lost productivity was valued using a U.S. daily production estimate. Analysis was conducted in 2017. Non-institutionalized adults with some lifetime exposure to intimate partner violence, sexual violence, or stalking (n=6,718 respondents; survey-weighted n=130,795,789) reported nearly 741 million lost productive days because of victimizations by an average of 2.5 perpetrators per victim. The adjusted per victim average was 4.9 (95% CI=3.9, 5.9) days, controlling for victim, perpetrator, and violence type factors. The estimated societal cost of this short-term lost productivity was $730 per victim, or $110 billion across the lifetimes of all victims (2016 USD). Factors associated with victims having a higher number of lost days included a higher number of perpetrators and being female, as well as sexual violence, physical violence, or stalking victimization by an intimate partner perpetrator, stalking victimization by an acquaintance perpetrator, and sexual violence or stalking victimization by a family member perpetrator. Short-term lost productivity represents a minimum economic valuation of the immediate negative effects of intimate partner violence, sexual violence, and stalking. Victims' lost productivity affects family members, colleagues, and employers. Published by Elsevier Inc.

The Othering of Domestic Violence

DEFF Research Database (Denmark)

Montoya, Celeste; Agustin, Lise Rolandsen

2013-01-01

Violence against women is a universal problem, affecting women at all levels of society; however, differently situated women have unique experiences with violence. Theoretically, this calls for the necessity to balance universality with intersectionality. Analyzing EU policy texts, we argue...... that the recognition of different forms of violence has led to an increased tendency toward culturalization, i.e. articulating culture as the only explanation behind certain forms of violence or focusing exclusively on culturalized forms of violence. While largely ignoring the gendered nature of violence, cultural...... framings of violence also create a dichotomy between “insiders” (non-violent Europeans) and “outsiders” (violent others)....

Ethnicities and violence

DEFF Research Database (Denmark)

Pedersen, Bodil Maria

Ethnicities and Violence Bodil Pedersen, University of Roskilde A recent publication (Thiara, Condon and Schröttle 2011) presents and discusses questions concerning diverse forms of violence against women from ethnic minorities in Europe. The issue raises unsolved questions of how to study...... as violence and what meanings do we attribute to it? What meanings does gender and ethnicities have for diverse participants in violent relations? What are their societal consequences and how do we study these? Central is also how we conceptualise and study questions concerning violence in minorised as well...... as against ethnic communities. On one hand our research should allow for conceptualising and studying specific practices in these communities. On the other hand - risking repeating and supporting dominant discourses of gendered violence as characteristic for them – we do not intend to represent them...

Explosive performance on the non-proliferation experiment

Energy Technology Data Exchange (ETDEWEB)

McKown, T.O. [Los Alamos National Lab., NM (United States)

1994-12-31

The Explosive Effects Physics Project at the Los Alamos National Laboratory planned and conducted experiments on the Non-Proliferation Experiment (NPE) as part of its effort to define source functions for seismic waves. Since all investigations were contingent on the performance of the emplaced chemical explosive, an array of diagnostic measurements was fielded in the emplaced explosive. The CORRTEX (COntinuous Reflectometry for Radius vs Time EXperiment) system was used to investigate the explosive initiation and to determine the detonation velocities on three levels and in a number of radial directions. The CORRTEX experiments fielded in the explosive chamber will be described, including a description of the explosive emplacement from the perspective of its impact on the CORRTEX results. The data obtained are reviewed and the resulting detonation velocities are reported. A variation of detonation velocity with depth in the explosive and the apparent underdetonation and overdetonation of the explosive in different radial directions is reported.

GENDER VIOLENCE IN EDUCATIONAL INSTITUTIONS

Directory of Open Access Journals (Sweden)

Rosalva Ruiz-Ramírez

2016-01-01

Full Text Available School violence is multifactorial. Social and cultural, family, personal, and institutional aspects, among others, influence educational institutions, in all academic levels. Because this type of violence is increasingly common and has serious consequences, there is a need to prevent and deal with the different types of violence practiced in schools, such as bullying, mobbing, gender violence, and others. Gender violence in institutions is not produced in this scope, in the strict sense, but rather has its origin in social and cultural aspects, rooted in the patriarchal and androcentric culture. Much has been written on the different forms in which violence affects mostly women in the educational system. This essay, without being thorough, attempts to answer three basic questions on gender violence in educational institutions: Why is there gender violence in educational institutions? How is gender violence manifested in schools? And finally, what actions have been taken to mitigate aggressions against women?

The behavior limestone under explosive load

Science.gov (United States)

Orlov, M. Yu; Orlova, Yu N.; Bogomolov, G. N.

2016-11-01

Limestone behavior under explosive loading was investigated. The behavior of the limestone by the action of the three types of explosives, including granular, ammonite and emulsion explosives was studied in detail. The shape and diameter of the explosion craters were obtained. The observed fragments after the blast have been classified as large, medium and small fragments. Three full-scale experiments were carried out. The research results can be used as a qualitative test for the approbation of numerical methods.

Violence against Amazon women.

Science.gov (United States)

Lima, Vera Lúcia de Azevedo; Souza, Maria de Lourdes de; Monticelli, Marisa; Oliveira, Marília de Fátima Vieira de; Souza, Carlos Benedito Marinho de; Costa, Carlos Alberto Leal da; Brüggemann, Odaléa Maria

2009-01-01

This quantitative and exploratory study analyzed violence against Amazon women presented in print media according to type and severity, and whether aggressors fell under the Maria da Penha law. A total of 181 issues of a regional newspaper were consulted. Based on content analysis, 164 items addressing violence against women were selected and 46 were included in the corpus of analysis. Results were gathered in three thematic groups: women killed with cruelty, sexual violence against women regardless of age, and violence against women and the limitations of the Maria da Penha law. Violence against these women varied in terms of form and severity, including up to homicide. Women are submitted to sexual violence from childhood through adulthood. The enforcement of this law shows the community it has a means to cope with this social phenomenon.

Preemptive Architecture: Explosive Art and Future Architectures in Cursed Urban Zones

Directory of Open Access Journals (Sweden)

Stahl Stenslie

2017-04-01

Full Text Available This article describes the art and architectural research project Preemptive Architecture that uses artistic strategies and approaches to create bomb-ready architectural structures that act as instruments for the undoing of violence in war. Increasing environmental usability through destruction represents an inverse strategy that reverses common thinking patterns about warfare, art and architecture. Building structures predestined for a construc­tive destruction becomes a creative act. One of the main motivations behind this paper is to challenge and expand the material thinking as well as the socio-political conditions related to artistic, architectural and design based practices.   Article received: December 12, 2016; Article accepted: January 10, 2017; Published online: April 20, 2017 Original scholarly paper How to cite this article: Stenslie, Stahl, and Magne Wiggen. "Preemptive Architecture: Explosive Art and Future Architectures in Cursed Urban Zones." AM Journal of Art and Media Studies 12 (2017: 29-39. doi: 10.25038/am.v0i12.165

Phenomenological modelling of steam explosions

International Nuclear Information System (INIS)

Corradini, M.L.; Drumheller, D.S.

1980-01-01

During a hypothetical core meltdown accident, an important safety issue to be addressed is the potential for steam explosions. This paper presents analysis and modelling of experimental results. There are four observations that can be drawn from the analysis: (1) vapor explosions are suppressed by noncondensible gases generated by fuel oxidation, by high ambient pressure, and by high water temperatures; (2) these effects appear to be trigger-related in that an explosion can again be induced in some cases by increasing the trigger magnitude; (3) direct fuel liquid-coolant liquid contact can explain small scale fuel fragmentation; (4) heat transfer during the expansion phase of the explosion can reduce the work potential

Urban children's perceptions of violence.

Science.gov (United States)

Sheehan, Karen; Kim, Lynn E; Galvin, John P

2004-01-01

To determine how preadolescent urban children conceptualize and experience violence in their lives. This qualitative study reports the results of focus groups designed to examine perceptions of violence among preadolescent urban children. Program directors were trained to conduct the sessions using a semistructured script. All groups were audiotaped or videotaped. The summaries were analyzed for recurring themes. A community-based visual arts program for children designed to be a secondary violence-prevention program. There were 12 focus groups of volunteer participants. Each consisted of 3 to 6 children aged 8 to 12 years, separated by sex and age. Fifty children participated: 27 boys and 23 girls. These children defined violence in a broader way than most adults would. Not only did the children identify shootings and stabbings as examples of violence, but they also considered violence to be any act that might hurt someone's feelings (such as cheating and lying) or any act accompanying violence (such as cursing and yelling). The boys and girls were very similar in their views except regarding the issue of intimate-partner violence. The girls were almost universally concerned about this issue, but the boys seemed noticeably unaware that intimate-partner violence was considered a form of violence. Most children felt safe at home, and almost no child felt safe at school. They looked to trusted adults to keep them safe. Future investigators measuring the effect of violence-prevention activities on preteen children should be aware that their definition of violence may differ from that of young children and should be cognizant of potential sex differences, especially around the topic of intimate-partner violence. Those designing violence-prevention programs for children should consider engaging adult family members as well because children usually turn to them for safety.

Explosions and static electricity

DEFF Research Database (Denmark)

Jonassen, Niels M

1995-01-01

The paper deals with the problem of electrostatic discharges as causes of ignition of vapor/gas and dust/gas mixtures. A series of examples of static-caused explosions will be discussed. The concepts of explosion limits, the incendiveness of various discharge types and safe voltages are explained...

Ammonium nitrate explosion hazards

Directory of Open Access Journals (Sweden)

Negovanović Milanka

2015-01-01

Full Text Available Ammonium nitrate (AN primarily is used as a fertilizer but it is also very important compound in the production of industrial explosives. The application of ammonium nitrate in the production of industrial explosives was related with the early era of Nobel dynamite and widely increased with the appearance of blasting agents such as ANFO and Slurry, in the middle of the last Century. Throughout the world millions of tons of ammonium nitrate are produced annually and handled without incident. Although ammonium nitrate generally is used safely, accidental explosions involving AN have high impact resulting in loss of lives and destruction of property. The paper presents the basic properties of ammonium nitrate as well as hazards in handling of ammonium nitrate in order to prevent accidents. Several accidents with explosions of ammonium nitrate resulted in catastrophic consequences are listed in the paper as examples of non-compliance with prescribed procedures.

Living in violence: Neighborhood domestic violence and small for gestational age births.

Science.gov (United States)

Felker-Kantor, Erica; Wallace, Maeve; Theall, Katherine

2017-07-01

To determine the association between neighborhood domestic violence and small-for-gestational-age (SGA) birth and to examine if there is a differential impact of neighborhood domestic violence on SGA births by race in a high crime community. This analysis includes all birth records issued in New Orleans, Louisiana from 2011 to 2012 geocoded by census tract (N=177 census tracts, N=8322 women). Hierarchical modeling and ecologic spatial analysis were used to examine the area-effect of neighborhood domestic violence on SGA births, independent of individual-level predictors and accounting for the propensity to live in high domestic violence neighborhoods. Tests for spatial autocorrelation reveled area-level clustering and overlap of SGA and domestic violent rates. Pregnant women living in high domestic violence areas were more likely to give birth to an SGA infant compared to women in low-domestic violence areas (OR=1.04, 95%CI: 1.01, 1.08), net of the effects of individual-level factors and propensity scores. Neighborhood-level attributes including rates of domestic violence may increase women's risk for SGA birth, highlighting a policy-relevant and potentially amenable exposure. Copyright © 2017 Elsevier Ltd. All rights reserved.

THE DOMESTIC VIOLENCE ON CHILDREN

Directory of Open Access Journals (Sweden)

SAVCA Lucia

2017-11-01

Full Text Available Any form of domestic violence leaves its mark on minority's personality forma¬tion and generates dysfunctions in the behavioral, cognitive and emotional sphere. The study found that in the modern family up to 30% of children suffer from physical violence and up to 45% by psychological violence. Sexual violence, unlike other forms of violence, is more difficult to discover. It has more dramatic consequences and re¬quires a longer time for psychological recovery. In this study, are described a few cases of sexual violence in the family literally

Explosive Characteristics of Carbonaceous Nanoparticles

Science.gov (United States)

Turkevich, Leonid; Fernback, Joseph; Dastidar, Ashok

2013-03-01

Explosion testing has been performed on 20 codes of carbonaceous particles. These include SWCNTs (single-walled carbon nanotubes), MWCNTs (multi-walled carbon nanotubes), CNFs (carbon nanofibers), graphene, diamond, fullerene, carbon blacks and graphites. Explosion screening was performed in a 20 L explosion chamber (ASTM E1226-10 protocol), at a (dilute) concentration of 500 g/m3, using a 5 kJ ignition source. Time traces of overpressure were recorded. Samples exhibited overpressures of 5-7 bar, and deflagration index KSt = V1/3 (dp/pt)max ~ 10 - 80 bar-m/s, which places these materials in European Dust Explosion Class St-1 (similar to cotton and wood dust). There was minimal variation between these different materials. The explosive characteristics of these carbonaceous powders are uncorrelated with particle size (BET specific surface area). Additional tests were performed on selected materials to identify minimum explosive concentration [MEC]. These materials exhibit MEC ~ 101 -102 g/m3 (lower than the MEC for coals). The concentration scans confirm that the earlier screening was performed under fuel-rich conditions (i.e. the maximum over-pressure and deflagration index exceed the screening values); e.g. the true fullerene KSt ~ 200 bar-m/s, placing it borderline St-1/St-2. Work supported through the NIOSH Nanotechnology Research Center (NTRC)

Surface energy of explosive nanoparticles

Science.gov (United States)

Pineau, Nicolas; Bidault, Xavier; Soulard, Laurent

2017-06-01

Recent experimental studies show that nanostructuration has a substantial impact on the detonation of high explosives: a nanostructured one leads to smaller nanodiamonds than a microstructured one. Whether it comes from a higher surface energy or from porosity, the origin of these different behaviors must be investigated. The surface energy of TATB nanoparticles with a radius from 2 nm upto 60 nm has been determined by means of ReaxFF-based simulations. Then, using the Rankine-Hugoniot relations and the equation of states of the bulk material, the contribution of this excess energy to the heating of a shock-compressed nanostructured (and porous) material is evaluated and compared to the thermal effect due to its porosity collapse. A maximum temperature increase of 50 K is found for 4-nm nanoparticles, which remains negligible when compared to the few hundred degrees induced by the compaction work.

27 CFR 555.181 - Reporting of plastic explosives.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Reporting of plastic..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.181 Reporting of plastic explosives. All persons, other than an agency of the United States...

Stalking and Violence.

Science.gov (United States)

Ostermeyer, Britta; Friedman, Susan Hatters; Sorrentino, Renee; Booth, Brad D

2016-12-01

The three widely known stalker classifications assist in categorizing stalkers, which allows for better management of violence risk. Although 80% of stalking is done by men, women also engage in stalking, and their violence risk should not be underestimated. Juvenile stalkers do exist and juvenile stalking is also associated with violence. Clinicians can become a victim of stalking and may become victims of stalking by proxy, a special type of stalking behavior where the stalker involves other people or agencies to communicate with or track their victim. A careful stalking violence risk assessment is essential in the intervention and risk management process. Copyright © 2016 Elsevier Inc. All rights reserved.

Insights into explosion dynamics at Stromboli in 2009 from ash samples collected in real-time

Science.gov (United States)

Taddeucci, J.; Lautze, N.; Andronico, D.; D'Auria, L.; Niemeijer, A.; Houghton, B.; Scarlato, P.

2012-04-01

Rapid characterization of tephra during explosive eruptions can provide valuable insights into eruptive mechanisms, also integrating other monitoring systems. Here we reveal a perspective on Stromboli's conduit processes by linking ash textures to geophysical estimates of eruption parameters of observed explosions. A three day campaign at Stromboli was undertaken by Italy's Istituto Nazionale di Geofisica e Vulcanologia (INGV) in October 2009. At this time activity was moderately intense, with an average 4 to 5, both ash-rich and ash-poor, explosions per hour at each the SW and NE vents. A total of fifteen ash samples were collected in real time. We used binocular and scanning electron microscopes to analyze the components, grain size and morphology distributions, and surface chemistry of ash particles within eight selected samples. In addition, the INGV monitoring network provided visual, thermal, and seismic information on the explosions that generated the sampled ash. In each sample, the proportion of fluidal, glassy sideromelane (as opposed to blocky, microcrystalline tachylite plus lithics), the degree of "chemical freshness" (as opposed to chemical alteration), and the average size of particles appear to correlate directly with the maximum height and the seismic amplitude of the corresponding explosion, and inversely correlate with the amount of ash erupted, as estimated by monitoring videos. These observations suggest that more violent explosions (i.e., those driven by the release of larger and more pressurized gas volumes) produce ash via the fragmentation of hotter, more fluid magma, while weaker ones mostly erupt ash-sized particles derived by the fragmentation of colder magma and incorporation of conduit wall debris. The formation of fluidal ash particles (up to Pele's hairs) requires aerodynamic deformation of a relatively low-viscosity magma, in agreement with the strong acceleration imposed upon fragmented magma clots by the rapid expansion of

Failure at Zainsk thermal power station: lesson for thermal and nuclear power stations

International Nuclear Information System (INIS)

Derkach, A.L.; Klyuchnikov, A.A.; Fedorenko, G.M.; Kuz'min, V.V.

2007-01-01

An account of system failure at Zainsk Thermal PS on January 1-st, 1979 is given. The cause of failure - sudden unauthorized energizing of block transformer which led to a direct asynchronous start of 200 MW turbine generator from grid. The failure resulted in the explosion and fire in generator, shaft destruction, and the damage of the machine hall's roof. The core roots of the failure have been scrutinised

Violence as Understandable, Deserved or Unacceptable? Listening for Gender in Teenagers' Talk about Violence

Science.gov (United States)

Sundaram, Vanita

2013-01-01

Youth violence is a topic of increasing global concern. Research has primarily focused on young people's responses to existing definitions of violence in seeking to understand how best to develop violence prevention. Little work has explored how young people themselves define violence and the factors which influence their acceptance, and use, of…

Workplace violence

NARCIS (Netherlands)

Bossche, S. van den

2014-01-01

Workplace violence refers to incidents where workers are abused, threatened or assaulted, either by people from within or outside their workplace. Workplace violence may have severe negative consequences for the workers affected, their co-workers and families; as well as for organisations and the

EVENT, Explosive Transients in Flow Networks

International Nuclear Information System (INIS)

Andrae, R.W.; Tang, P.K.; Bolstad, J.W.; Gregory, W.S.

1985-01-01

1 - Description of problem or function: A major concern of the chemical, nuclear, and mining industries is the occurrence of an explosion in one part of a facility and subsequent transmission of explosive effects through the ventilation system. An explosive event can cause performance degradation of the ventilation system or even structural failures. A more serious consequence is the release of hazardous materials to the environment if vital protective devices such as air filters, are damaged. EVENT was developed to investigate the effects of explosive transients through fluid-flow networks. Using the principles of fluid mechanics and thermodynamics, governing equations for the conservation of mass, energy, and momentum are formulated. These equations are applied to the complete network subdivided into two general components: nodes and branches. The nodes represent boundaries and internal junctions where the conservation of mass and energy applies. The branches can be ducts, valves, blowers, or filters. Since in EVENT the effect of the explosion, not the characteristics of the explosion itself, is of interest, the transient is simulated in the simplest possible way. A rapid addition of mass and energy to the system at certain locations is used. This representation is adequate for all of the network except the region where the explosion actually occurs. EVENT84 is a modification of EVENT which includes a new explosion chamber model subroutine based on the NOL BLAST program developed at the Naval Ordnance Laboratory, Silver Spring, Maryland. This subroutine calculates the confined explosion near-field parameters and supplies the time functions of energy and mass injection. Solid-phase or TNT-equivalent explosions (which simulate 'point source' explosions in nuclear facilities) as well as explosions in gas-air mixtures can be simulated. The four types of explosions EVENT84 simulates are TNT, hydrogen in air, acetylene in air, and tributyl phosphate (TBP or 'red oil

Reduction of radioactivity produced by nuclear explosives

Energy Technology Data Exchange (ETDEWEB)

Lessler, Richard M [Lawrence Radiation Laboratory, University of California, Livermore, CA (United States)

1970-05-15

Four main sources contribute to the radioactivity produced by a nuclear explosive: 1. Fission products from the nuclear explosive, 2. Fusion products from the nuclear explosive, 3. Induced radioactivity in the nuclear explosive, 4. Induced radioactivity in the environment. This paper will summarize some of the work done at the Lawrence Radiation Laboratory at Livermore to reduce the radioactivity from these sources to levels acceptable for peaceful applications. Although it is theoretically possible to have no radioactivity produced by nuclear explosives, this goal has not been achieved.

Violence and Asthma: A Review

Directory of Open Access Journals (Sweden)

Takeo Fujiwara

2008-01-01

Full Text Available Recent research shows that exposure to community violence is, directly and indirectly, associated with asthma. This article reviews the findings on the impact of violence on asthma, and the pathways for the association of violence and asthma are suggested: 1 exposure to violence is directly associated with asthma, mainly through dysregulation of sympathetic-adrenal-medullary (SAM and hypothalamic-pituitary-adrenal (HPA axis, 2 exposure to violence is associated with the change of susceptibility of outdoor air pollution on asthma, probably through the change of an immune response, and 3 behavioral change due to exposure to violence (e.g. keeping children indoors leads to more exposure to indoor pollutants. The suggested framework may be useful to develop health policy on asthma in high-violence communities.

Predictors of dating violence among Chinese adolescents: the role of gender-role beliefs and justification of violence.

Science.gov (United States)

Shen, April Chiung-Tao; Chiu, Marcus Yu-Lung; Gao, Jianxiu

2012-04-01

In Chinese societies, violence among adolescent dating partners remains a largely ignored and invisible phenomenon. The goal of this study is to examine the relationships among gender-role beliefs, attitudes justifying dating violence, and the experiences of dating-violence perpetration and victimization among Chinese adolescents. This study has used self-reporting measures to collect data from a probability sample of 976 adolescents (mean age = 15.9) in three Chinese societies: Taiwan, Hong Kong, and Shanghai. Research results reveal a high prevalence of dating violence (including physical violence, sexual violence, and controlling behavior) among Chinese adolescents with dating experience: the perpetration rate is 27.3% and the victimization rate is 39%. Study results demonstrate that adolescents who endorse traditional gender-role beliefs tend to view dating violence as acceptable behavior. Boys' endorsement of traditional gender roles, boys' attitudes justifying boy-on-girl violence, and boys' attitudes against girl-on-boy violence predict boys' actual sexual-violence behavior. Moreover, boys' attitudes justifying boy-on-girl dating violence is the strongest predictor of boys' perpetration of physical and sexual dating violence. This study also shows that boys' hostility is a significant predictor of boys' controlling behavior. Programs for preventing dating violence should include components designed to challenge traditional gender-role beliefs and attitudes justifying dating violence.

Predicting inpatient violence using the Broset Violence Checklist (BVC).

Science.gov (United States)

Almvik, R; Woods, P

1999-01-01

This paper reports early analysis of the Broset Violence Checklist. An instrument aiming to assist in the process of the prediction of violence from mentally ill in-patients. Early results appear promising and directions for future research using the instrument are suggested.

Characteristics of a plasma flow field produced by a metal array bridge foil explosion

Science.gov (United States)

Junying, WU; Long, WANG; Yase, LI; Lijun, YANG; Manzoor, SULTAN; Lang, CHEN

2018-07-01

To improve the energy utilization efficiency of metal bridge foil explosion, and increase the function range of plasmas, array bridge foil explosion experiments with different structures were performed. A Schlieren photographic measurement system with a double-pulse laser source was used to observe the flow field of a bridge foil explosion. The evolution laws of plasmas and shock waves generated by array bridge foil explosions of different structures were analyzed and compared. A multi-phase flow calculation model was established to simulate the electrical exploding process of a metal bridge foil. The plasma equation of state was determined by considering the effect of the changing number of particles and Coulomb interaction on the pressure and internal energy. The ionization degree of the plasma was calculated via the Saha–Eggert equation assuming conditions of local thermal equilibrium. The exploding process of array bridge foils was simulated, and the superposition processes of plasma beams were analyzed. The variation and distribution laws of the density, temperature, pressure, and other important parameters were obtained. The results show that the array bridge foil has a larger plasma jet diameter than the single bridge foil for an equal total area of the bridge foil. We also found that the temperature, pressure, and density of the plasma jet’s center region sharply increase because of the superposition of plasma beams.

Physicians and domestic violence

OpenAIRE

Joslin, Jonathan

1994-01-01

Domestic violence, spouse abuse, and battering all refer to the victimization of a person with whom the abuser has or has had an intimate relationship. Domestic violence may take the form of physical, sexual and psychological abuse, is generally repeated, and often escalates within relationships. Most evidence indicates that domestic violence is predominantly perpetrated by men against women. Some evidence suggests that women are just as likely to use violence against male partners as men are...

Explosions of Thorne-Żytkow objects

Science.gov (United States)

Moriya, Takashi J.

2018-03-01

We propose that massive Thorne-Żytkow objects can explode. A Thorne-Żytkow object is a theoretically predicted star that has a neutron core. When nuclear reactions supporting a massive Thorne-Żytkow object terminate, a strong accretion occurs towards the central neutron core. The accretion rate is large enough to sustain a super-Eddington accretion towards the neutron core. The neutron core may collapse to a black hole after a while. A strong large-scale outflow or a jet can be launched from the super-Eddington accretion disc and the collapsing Thorne-Żytkow object can be turned into an explosion. The ejecta have about 10 M⊙ but the explosion energy depends on when the accretion is suppressed. We presume that the explosion energy could be as low as ˜1047 erg and such a low-energy explosion could be observed like a failed supernova. The maximum possible explosion energy is ˜1052 erg and such a high-energy explosion could be observed as an energetic Type II supernova or a superluminous supernova. Explosions of Thorne-Żytkow objects may provide a new path to spread lithium and other heavy elements produced through the irp process such as molybdenum in the Universe.

Infrared photothermal imaging of trace explosives on relevant substrates

Science.gov (United States)

Kendziora, Christopher A.; Furstenberg, Robert; Papantonakis, Michael; Nguyen, Viet; Borchert, James; Byers, Jeff; McGill, R. Andrew

2013-06-01

We are developing a technique for the stand-off detection of trace explosives on relevant substrate surfaces using photo-thermal infrared (IR) imaging spectroscopy (PT-IRIS). This approach leverages one or more compact IR quantum cascade lasers, tuned to strong absorption bands in the analytes and directed to illuminate an area on a surface of interest. An IR focal plane array is used to image the surface and detect small increases in thermal emission upon laser illumination. The PT-IRIS signal is processed as a hyperspectral image cube comprised of spatial, spectral and temporal dimensions as vectors within a detection algorithm. The ability to detect trace analytes on relevant substrates is critical for stand-off applications, but is complicated by the optical and thermal analyte/substrate interactions. This manuscript describes recent PT-IRIS experimental results and analysis for traces of RDX, TNT, ammonium nitrate (AN) and sucrose on relevant substrates (steel, polyethylene, glass and painted steel panels). We demonstrate that these analytes can be detected on these substrates at relevant surface mass loadings (10 μg/cm2 to 100 μg/cm2) even at the single pixel level.

Explosives mimic for testing, training, and monitoring

Science.gov (United States)

Reynolds, John G.; Durban, Matthew M.; Gash, Alexander E.; Grapes, Michael D.; Kelley, Ryan S.; Sullivan, Kyle T.

2018-02-13

Additive Manufacturing (AM) is used to make mimics for explosives. The process uses mixtures of explosives and matrices commonly used in AM. The explosives are formulated into a mixture with the matrix and printed using AM techniques and equipment. The explosive concentrations are kept less than 10% by wt. of the mixture to conform to requirements of shipping and handling.

Dynamic mechanical and molecular weight measurements on polymer bonded explosives from thermally accelerated aging tests. III. Kraton block copolymer binder and plasticizers

International Nuclear Information System (INIS)

Caley, L.E.; Hoffman, D.M.

1981-01-01

The dynamic mechanical properties and molecular weight distribution of two experimental polymer bonded explosives, X-0287 and X-0298, maintained at 23, 60, and 74 0 C for 3 years were examined. X-0287 is 97% 1,3,5,7-tetranitro-1,3,5,7-tetraazacyclooctane explosive, 1.8% Kraton G-1650, and 1.2% B 2 was 170. X-0298 is 97.4% explosive, 1.4% Kraton G-1650, and 1.2% Cenco Hi-vac oil. The relaxation associated with the Kraton rubber block glass transition is observed in both X-0287 and X-0298. In the unaged X-0298 it occurs at -59 0 C and in the aged explosive at 50 0 C. This is caused by migration of the oil plasticizer out of the explosive. In X-0287 the Kraton rubber block T/sub g/ is weak and broad due to the presence of the wax plasticizer. X-0287 has a second broad relaxation associated with the melting of the wax from 10 to 65 0 C. The molecular weight of the Kraton binder decreased with increasing accelerated aging temperature. The oil plasticizer had no stabilizing effect, but below its melting point the wax reduced Kraton chain scission considerably. The simple random chain scission model predicted a 20.5 year use-life for X-0298, but X-0287 was stabilized against degradation below the wax melting point

Sensation Seeking in Street Violence

DEFF Research Database (Denmark)

Heinskou, Marie Bruvik; Liebst, Lasse Suonperä

Sensation seeking leads to violence—runs an influential hypothesis in the social scientific study of violent behavior. Although studies confirm that violence is sometimes structured by sensation-seeking motives, the literature seldom comments on the limits to this explanation of violence....... The present study examines the scale of violence motivated by sensation seeking and the degree to which there are several distinct forms of sensation seeking motives operative in violence, rather than a sensation-seeking motive in the singular. The study draws on a sample of situations from Copenhagen...... involving street violence, which are coded quantitatively and qualitatively. Our analysis shows that sensation seeking only seldom seems to play a role in the structuring of street violence. Moreover, the data indicate that sensation seeking finds expression in street violence situations in two different...

Effect of type of explosives and physical-mechanical properties of explosive rock on formation of toxic gases in atmosphere of shafts

Science.gov (United States)

Mindeli, E. O.; Khudyakov, M. Y.

1981-01-01

The quality of toxic gases formed during explosive work in underground shafts depends upon the type of explosives and the conditions of explosion. Several types of explosives and rocks were examined. All remaining conditions were maintained the same (sandy-argillaceous stemming, electrical method of explosions, diameter of blast holes, and the direct triggering of charges).

Witnessing Partner Violence: Exploring the Role of Partner Preferences on Dating Violence.

Science.gov (United States)

Gonzalez-Mendez, Rosaura; Yanes, José M; Ramírez-Santana, Gustavo

2015-06-02

Research has shown that witnessing partner violence (WPV) increases the likelihood of experiencing or perpetrating violence in later romantic relationships, but little is known about the mechanisms underlying this process. This study examines the relationships between preference for unsuitable partners and teen dating violence (TDV) among adolescents who have witnessed parental violence or not. Attachment was also considered. Participants were 356 adolescents, both witnesses and non-witnesses of partner violence. Results showed no difference in preferences (for good, risky, or loving partners) between the two groups. However, preference for unsuitable partners did significantly predict TDV perpetration and victimization, but only among witnesses. Also, loving-partner preference moderates the relationship between WPV and TDV perpetration among highly avoidant witnesses. Findings indicate a new avenue for prevention through targeting partner preferences. © The Author(s) 2015.

Testing the Cycle of Violence Hypothesis: Child Abuse and Adolescent Dating Violence as Predictors of Intimate Partner Violence in Young Adulthood

Science.gov (United States)

Gomez, Anu Manchikanti

2011-01-01

Child abuse is an important determinant of future violence perpetration and victimization. Past research examining linkages between child abuse and adult intimate partner violence (IPV) has predominantly focused on married individuals and not considered adolescent dating violence. In the present study, data from three waves of the National…

The sensitivity studies of a landmine explosive detection system based on neutron backscattering using Monte Carlo simulation

Directory of Open Access Journals (Sweden)

Khan Hamda

2017-01-01

Full Text Available This paper carries out a Monte Carlo simulation of a landmine detection system, using the MCNP5 code, for the detection of concealed explosives such as trinitrotoluene and cyclonite. In portable field detectors, the signal strength of backscattered neutrons and gamma rays from thermal neutron activation is sensitive to a number of parameters such as the mass of explosive, depth of concealment, neutron moderation, background soil composition, soil porosity, soil moisture, multiple scattering in the background material, and configuration of the detection system. In this work, a detection system, with BF3 detectors for neutrons and sodium iodide scintillator for g-rays, is modeled to investigate the neutron signal-to-noise ratio and to obtain an empirical formula for the photon production rate Ri(n,γ= SfGfMf(d,m from radiative capture reactions in constituent nuclides of trinitrotoluene. This formula can be used for the efficient landmine detection of explosives in quantities as small as ~200 g of trinitrotoluene concealed at depths down to about 15 cm. The empirical formula can be embedded in a field programmable gate array on a field-portable explosives' sensor for efficient online detection.

Molecular Outflows: Explosive versus Protostellar

Energy Technology Data Exchange (ETDEWEB)

Zapata, Luis A.; Rodríguez, Luis F.; Palau, Aina; Loinard, Laurent [Instituto de Radioastronomía y Astrofísica, UNAM, Apdo. Postal 3-72 (Xangari), 58089 Morelia, Michoacán, México (Mexico); Schmid-Burgk, Johannes [Max-Planck-Institut für Radioastronomie, Auf dem Hügel 69, D-53121, Bonn (Germany)

2017-02-10

With the recent recognition of a second, distinctive class of molecular outflows, namely the explosive ones not directly connected to the accretion–ejection process in star formation, a juxtaposition of the morphological and kinematic properties of both classes is warranted. By applying the same method used in Zapata et al., and using {sup 12}CO( J = 2-1) archival data from the Submillimeter Array, we contrast two well-known explosive objects, Orion KL and DR21, to HH 211 and DG Tau B, two flows representative of classical low-mass protostellar outflows. At the moment, there are only two well-established cases of explosive outflows, but with the full availability of ALMA we expect that more examples will be found in the near future. The main results are the largely different spatial distributions of the explosive flows, consisting of numerous narrow straight filament-like ejections with different orientations and in almost an isotropic configuration, the redshifted with respect to the blueshifted components of the flows (maximally separated in protostellar, largely overlapping in explosive outflows), the very-well-defined Hubble flow-like increase of velocity with distance from the origin in the explosive filaments versus the mostly non-organized CO velocity field in protostellar objects, and huge inequalities in mass, momentum, and energy of the two classes, at least for the case of low-mass flows. Finally, all the molecular filaments in the explosive outflows point back to approximately a central position (i.e., the place where its “exciting source” was located), contrary to the bulk of the molecular material within the protostellar outflows.

Canada's family violence initiative: partnerships

OpenAIRE

Scott,Elaine

1994-01-01

Under Canada's four-year, $136 million Family Violence Initiative, the federal government is calling upon all Canadians to work in partnerships towards the elimination of family violence - child abuse, violence against women, and elder (senior) abuse. Family violence is a complex problem and requires the efforts of all Canadians to resolve it. One of the key themes of the Initiative - a multidisciplinary approach to the problem of family violence - is reflected in the selection and developmen...

Family Violence.

Science.gov (United States)

Emery, Robert E.

1989-01-01

Researchers and policymakers have begun to recognize the extent and severity of family violence, particularly its effects on children. But there is much disagreement about the definition of violence, its development, the consequences for victims, and the most effective avenues for intervention. Advances recommendations for further research.…

Intimate Partner Violence. Prevention Update

Science.gov (United States)

Higher Education Center for Alcohol, Drug Abuse, and Violence Prevention, 2011

2011-01-01

The Centers for Disease Control and Prevention (CDC) defines intimate partner violence (IPV) as violence between two people in a close relationship, including current and former spouses and dating partners. IPV occurs on a continuum from a single episode to ongoing battering and can include physical violence, sexual violence, threats, emotional…

The Relationship of Abortion and Violence Against Women: Violence Prevention Strategies and Research Needs.

Science.gov (United States)

Coyle, Catherine T; Shuping, Martha W; Speckhard, Anne; Brightup, Jennie E

2015-01-01

From the perspective of peace psychology, the role of abortion in acts of violence against women is explored, with a focus on violence-prevention strategies. Setting aside the political debate, this task force report takes the conflict-transformation approach of considering all perspectives that have concern for the right of women to avoid being victims of violence. The evidence that victims of Intimate Partner Violence are disproportionately represented in women presenting for abortion suggests a need for screening at clinics. Coerced abortion is a form of violence and has occurred by government policy in China and as a result of other violence against women: sex trafficking and war situations. Sex-selection abortion of female fetuses, referred to as "gendercide," has reached pandemic proportions and caused a gender imbalance in some countries. Psychology, through empirical research, can make unique contributions to understanding the relationship between abortion and violence and in developing prevention strategies.

Violence on canadian television networks.

Science.gov (United States)

Paquette, Guy

2004-02-01

Over the past twenty years, the question of the effects of violence on television has figured prominently in public opinion and hundreds of studies have been devoted to this subject. Many researchers have determined that violence has a negative impact on behavior. The public, broadcasters and political figures all support the idea of reducing the total amount of violence on television - in particular in shows for children. A thousand programs aired between 1993 and 2001 on major non-specialty television networks in Canada were analyzed: TVA, TQS, as well as CTV and Global, private French and English networks, as well as the English CBC Radio and French Radio-Canada for the public networks. The methodology consists of a classic analysis of content where an act of violence constitutes a unit of analysis. The data collected revealed that the amount of violence has increased regularly since 1993 despite the stated willingness on the part of broadcasters to produce programs with less violence. The total number of violent acts, as well as the number of violent acts per hour, is increasing. Private networks deliver three times more violence than public networks. Researchers have also noted that a high proportion of violence occurs in programs airing before 21:00 hours, thereby exposing a large number of children to this violence. Psychological violence is taking on a more significant role in Canadian Television.

Suppression of stratified explosive interactions

Energy Technology Data Exchange (ETDEWEB)

Meeks, M.K.; Shamoun, B.I.; Bonazza, R.; Corradini, M.L. [Wisconsin Univ., Madison, WI (United States). Dept. of Nuclear Engineering and Engineering Physics

1998-01-01

Stratified Fuel-Coolant Interaction (FCI) experiments with Refrigerant-134a and water were performed in a large-scale system. Air was uniformly injected into the coolant pool to establish a pre-existing void which could suppress the explosion. Two competing effects due to the variation of the air flow rate seem to influence the intensity of the explosion in this geometrical configuration. At low flow rates, although the injected air increases the void fraction, the concurrent agitation and mixing increases the intensity of the interaction. At higher flow rates, the increase in void fraction tends to attenuate the propagated pressure wave generated by the explosion. Experimental results show a complete suppression of the vapor explosion at high rates of air injection, corresponding to an average void fraction of larger than 30%. (author)

[Domestic violence against women of a crisis intervention population - forms of violence and risk factors].

Science.gov (United States)

Nyberg, E; Stieglitz, R-D; Flury, M; Riecher-Rössler, A

2013-06-01

BACKGROUND AND HYPOTHESES: Domestic violence is common and can lead to severe physical and psychological problems. Thus, we have investigated the frequency of occurrence, forms and risk factors of domestic violence against female patients on a crisis intervention ward. 115 women were screened with the "screening spouse violence" (SPG) and the "index of spouse abuse" (ISA). The life time prevalence concerning spouse violence was 70 %. Out of 74 women who were currently living in a relationship 28 (38 % )were victims of violence in the last 12 months prior to their admission. Women who experienced violence had a significantly lower level of education. Screening for domestic violence in female patients in the field of crisis intervention and psychiatry should become a standard of "good clinical practice". © Georg Thieme Verlag KG Stuttgart · New York.

Glass produced by underground nuclear explosions

International Nuclear Information System (INIS)

Schwartz, L.; Piwinskii, A.; Ryerson, F.; Tewes, H.; Beiriger, W.

1983-01-01

Detonation of an underground nuclear explosive produces a strong shock wave which propagates spherically outward, vaporizing the explosive and nearby rock and melting, the surrounding rock. The vaporized material expands adiabatically, forming a cavity. As the energy is dissipated during the cavity formation process, the explosive and rock debris condense and mix with the melted rock. The melt flows to the bottom of the cavity where it is quenched by fractured rock fragments falling from above as the cavity collapses. Measurements indicate that about 740 tonnes of rock and/or soil are melted for every kiloton (10 12 calories) of explosive energy, or about 25% of the explosive energy goes to melting rock. The resulting glass composition reflects the composition of the unaltered rock with explosive debris. The appearance ranges from white pumice to dense, dark lava. The bulk composition and color vary with the amount of explosive iron incorporated into the glass. The refractory explosion products are mixed with the solidified melt, although the degree of mixing is variable. Electron microprobe studies of glasses produced by Rainier in welded tuff have produced the following results: glasses are dehydrated relative to the host media, glasses are extremely heterogeneous on a 20 μm scale, a ubiquitous feature is the presence of dark marble-cake regions in the glass, which were locally enriched in iron and may be related to the debris, optically amorphous regions provide evidence of shock melting, only limited major element redistribution and homogenization occur within the cavity

Neighborhood Interventions to Reduce Violence

Science.gov (United States)

Michelle C. Kondo; Elena Andreyeva; Eugenia C. South; John M. MacDonald; Charles C. Branas

2018-01-01

Violence is a widespread problem that affects the physical, mental, and social health of individuals and communities. Violence comes with an immense economic cost to its victims and society at large. Although violence interventions have traditionally targeted individuals, changes to the built environment in places where violence occurs show promise as practical,...

Steam explosion triggering phenomena: stainless steel and corium-E simulants studied with a floodable arc melting apparatus

International Nuclear Information System (INIS)

Nelson, L.S.; Buxton, L.D.

1978-05-01

Laboratory-scale experiments on the thermal interaction of light water reactor core materials with water have been performed. Samples (10--35 g) of Type 304 stainless steel and Corium-E simulants were each flooded with approximately 1.5 litres of water to determine whether steam explosions would occur naturally. Many of the experiments also employed artificially induced pressure transients in an attempt to initiate steam explosions. Vigorous interactions were not observed when the triggering pulse was not applied, and for stainless steel the triggering pulse initiated only coarse fragmentation. Two-stage, pressure-producing interactions were triggered for an ''oxidic'' Corium-E simulant. An impulse-initiated gas release theory has been simulated to explain the initial sample fragmentation. Although the delayed second stage of the event is not fully understood, it does not appear to be readily explained with classical vapor explosion theory. Rather, some form of metastability of the melt seems to be involved

Citoyenneté et formes de violence. La violence de genre en Amérique latine

OpenAIRE

Soriano, Michèle

2015-01-01

Dans son essai intitulé Critique de la violence, Walter Benjamin considère la violence dans ses rapports au droit. Il remarque que toute violence, en tant que moyen, « fonde le droit ou le conserve », et s’intéresse tout particulièrement à la violence létale ; il précise : « Dans l’exercice de la violence sur la vie et la mort, le droit lui-même se renforce plus que dans n’importe quelle autre de ses applications ». Le rapport que trace le philosophe entre la violence, la mort et le droit par...

The impact of violence on children.

Science.gov (United States)

Osofsky, J D

1999-01-01

Existing research on the effects of children's exposure to violence covers a broad range of community, family, and media violence. This research is relevant and useful to an examination of domestic violence in two key ways. First, understanding how exposure to various types of violence affects children and what best enables them to cope can point to important considerations when trying to help children cope with exposure to domestic violence in particular. And second, many families experiencing domestic violence are exposed to other types of violence as well. Exposure to violence on multiple levels can affect the parents' behavior and can compound the effects on children. This article begins with an overview of the extent of children's exposure to various types of violence, and then examines what is known about the effects of this exposure across the developmental continuum. Key protective factors for children exposed to violence are examined. Research indicates that the most important resource protecting children from the negative effects of exposure to violence is a strong relationship with a competent, caring, positive adult, most often a parent. Yet, when parents are themselves witnesses to or victims of violence, they may have difficulty fulfilling this role. In the final section, directions for future research are discussed.

Narratives of Domestic Violence

OpenAIRE

Hunter, Rosemary

2006-01-01

Second wave feminists in Australia brought the social issue of domestic violence out of the suburban shadows and into the activist and policy spotlight in the 1970s. Subsequent feminist-inspired law reforms around domestic violence included the introduction of state domestic violence order regimes in the 1980s, and amendments to the Family Law Act 1975 (Cth) in 1995 to specify family violence as one of the matters to be taken into account by the Family Court in\\ud determining the best interes...

Prevalence of Violence: Male and Female Seasonal Agricultural Workers' Approach to Violence in Turkey.

Science.gov (United States)

Şimşek, Zeynep; Kara, Burcu; Ersin, Fatma; Ökten, Şevket; Yıldırımkaya, Gökhan

2016-01-01

The objective of this study is to determine the male and female seasonal agricultural workers' perception of violence, prevalence of violence, frequency of victimization, and their related factors. Quantitative and qualitative data were used, and 89.5% of women were exposed to violence that included the restriction of their human rights. The sample consisted of 1,211 women and 1,064 men. Their marital status, duration of work, and attention to their health affected the violence exposure. Arabic people who were unmarried, had a poor educational background, and poor health perception approved of the physical violence.

Metaphors about violence by preservice teachers.

Science.gov (United States)

Özabaci, Nilüfer; Erkan, Zülal

2015-03-01

Violence consists of a pattern of coercive behaviors used by a competent adult or adolescent to establish and maintain power and control over another competent adult or adolescent. These behaviors, which can occur alone or in combination, sporadically or continually, include physical violence, psychological abuse, talking, and nonconsensual sexual behavior. Research indicates that different types of violence are used as a means of enforcing discipline in the family and the school context. Children and adolescents who grow up in an environment where violence has a natural place tend to resort to violence at every stage of their lives without question. The aim of this research was therefore to preservice teachers' perception of the concept of violence through the use of metaphors. Accordingly, answers to the following questions were sought: What metaphors do the youth use to describe the concept of violence? Under which conceptual categories can these metaphors be grouped in terms of their common features? How do the conceptual categories vary in relation to the students' gender and the subjects they study at university? The study was conducted in 2009 with the help of 303 students at Mersin University and Eskişehir Osmangazi University (Faculty of Education). Incomplete statements such as "Violence is like..., because..." were used in an attempt to understand the students' perception of violence. The students were given questionnaire to complete the statements. Demographic questions were also asked on the students'age, gender and departments. The data were analyzed through qualitative analysis, and processes such as frequency distribution and quantitative correlation data were evaluated through SPSS data analysis. It emerged that the students used 74 metaphors of violence that could be divided into seven categories: (1) Violence as a way of controlling others; 2) Violence as part of social and affective life; (3) Violence as devastation; (4) Violence as learned

Preventing Youth Violence: Opportunities for Action

Science.gov (United States)

David-Ferdon, Corinne; Simon, Thomas R.

2014-01-01

All forms of violence, including youth violence, suicidal behavior, child maltreatment, sexual violence, intimate partner violence, and elder abuse, negatively affect the health and well-being of this country. Youth violence, in particular, is a significant public health problem. Many young people and communities view the grim facts about youth…

Reactive thermal waves in energetic materials

Energy Technology Data Exchange (ETDEWEB)

Hill, Larry G [Los Alamos National Laboratory

2009-01-01

Reactive thermal waves (RTWs) arise in several energetic material applications, including self-propagating high-temperature synthesis (SHS), high explosive cookoff, and the detonation of heterogeneous explosives. In this paper I exmaine ideal RTWs, by which I mean that (1) material motion is neglected, (2) the state dependence of reaction is Arrhenius in the temperature, and (3) the reaction rate is modulated by an arbitrary mass-fraction-based reaction progress function. Numerical simulations demonstrate that one's natural intuition, which is based mainly upon experience with inert materials and which leads one to expect diffusion processes to become relatively slow after a short time period, is invalid for high energy, state-sensitive reactive systems. Instead, theory predicts that RTWs can propagate at very high speeds. This result agrees with estimates for detonating heterogeneous explosives, which indicate that RTWs must spread from hot-spot nucleation sites at rates comparable to the detonation speed in order to produce experimentally-observed reaction zone thicknesses. Using dimensionless scaling and further invoking the high activation energy approximation, I obtain an analytic formula for the steady plane RTW speed from numerical calculations. I then compute the RTW speed for real explosives, and discuss aspects of their behavior.

Violence against women: the physician's role.

Science.gov (United States)

Schmuel, E; Schenker, J G

1998-10-01

Violence against women is one reflection of the unequal power relationship between men and women in societies. Reflections of this inequality include marriage at a very young age, lack of information or choice about fertility control and forced pregnancy within marriage. The different forms of violence against women are: domestic violence and rape, genital mutilation or, gender-based violence by police and security forces, gender-based violence against women during armed conflict, gender-based violence against women refugees and asylum-seekers, violence associated with prostitution and pornography, violence in the workplace, including sexual harassment. Violence against women is condemned, whether it occurs in a societal setting or a domestic setting. It is not a private or family matter. The FIGO Committee for the Study of Ethical Aspects of Human Reproduction released statements to physicians treating women on this issue. Physicians are ethically obliged to inform themselves about the manifestations of violence and recognize cases, to treat the physical and psychological results of violence, to affirm to their patients that violent acts toward them are not acceptable and to advocate for social infrastructures to provide women the choice of seeking secure refuge and ongoing counselling.

Morphology of School Violence.

Science.gov (United States)

MacDonald, Irene

This paper discusses school violence, examining pertinent research, media, and policy documents. Section 1 examines the evolution of terminologies related to youth violence. Section 2 explains that when reviewing researchers' conclusions on school violence, it is important to consider the role perception had in determining those views. Section 3…

An Intersectional Analysis of Intimate Partner Violence and Workplace Violence among Women Working in Prostitution

Directory of Open Access Journals (Sweden)

PILAR RODRÍGUEZ MARTÍNEZ

2015-01-01

Full Text Available This article presents the results of a qualitative analysis of violence against women (intimate partner violence and workplace violence. The subject of the research is a qualitative sample of 12 autochthonous and migrant women who work in low-paid prostitution in Almería. The study uses an intersectional and multi-level approach, focusing on the perspectives of groups who experience multiple discrimination. The results show that violence has an impact on the identity of women. It also shows that in the different paths of the women in the study, different webs of violence occur, which lead them to distinct understandings of the violence they experience. In addition, we have analyzed how age, education level, and above all, social stigma, are related to the possibility of these women experiencing violence in their work and to their perceptions of that work.

Violence against emergency department employees and the attitude of employees towards violence.

Science.gov (United States)

Çıkrıklar, H Í; Yürümez, Y; Güngör, B; Aşkın, R; Yücel, M; Baydemir, C

2016-10-01

This study was conducted to evaluate the occurrence of violent incidents in the workplace among the various professional groups working in the emergency department. We characterised the types of violence encountered by different occupation groups and the attitude of individuals working in different capacities. This cross-sectional study included 323 people representing various professional groups working in two distinct emergency departments in Turkey. The participants were asked to complete questionnaires prepared in advance by the researchers. The data were analysed using the Statistical Package for the Social Sciences (Windows version 15.0). A total of 323 subjects including 189 (58.5%) men and 134 (41.5%) women participated in the study. Their mean (± standard deviation) age was 31.5 ± 6.5 years and 32.0 ± 6.9 years, respectively. In all, 74.0% of participants had been subjected to verbal or physical violence at any point since starting employment in a medical profession. Moreover, 50.2% of participants stated that they had been subjected to violence for more than 5 times. Among those who reported being subjected to violence, 42.7% had formally reported the incident(s). Besides, 74.3% of participants did not enjoy their profession, did not want to work in the emergency department, or would prefer employment in a non-health care field after being subjected to violence. According to the study participants, the most common cause of violence was the attitude of patients or their family members (28.7%). In addition, 79.6% (n=257) of participants stated that they did not have adequate safety protection in their working area. According to the study participants, there is a need for legal regulations to effectively deter violence and increased safety measures designed to reduce the incidence of violence in the emergency department. Violence against employees in the emergency department is a widespread problem. This situation has a strong negative effect on employee

Violence against female sex workers in Cameroon: accounts of violence, harm reduction, and potential solutions.

Science.gov (United States)

Lim, Sahnah; Peitzmeier, Sarah; Cange, Charles; Papworth, Erin; LeBreton, Matthew; Tamoufe, Ubald; Kamla, Aristide; Billong, Serge; Fokam, Pamella; Njindam, Iliassou; Decker, Michele R; Sherman, Susan G; Baral, Stefan

2015-03-01

Female sex workers (FSWs) in Cameroon, and West Africa generally, suffer a disproportionate burden of HIV. Although violence against FSWs has been documented extensively in other parts of the world, data on violence from West African countries are lacking. The aim of this study was to qualitatively document violence and harm reduction strategies from the perspective of FSWs in Cameroon as well as to understand how experiences of violence may increase FSWs' HIV risk. FSWs from 7 major cities in Cameroon (Douala, Yaounde, Bamenda, Bertoua, Nagoundere, Kribi, and Bafoussam) were purposively recruited. Data from 31 in-depth interviews and 7 focus groups (n = 70; with some overlapping participants from in-depth interviews) conducted with these FSWs in 6 of these 7 cities (excluding Kribi) were analyzed using a grounded theory approach. Transcripts revealed 3 primary themes related to violence: (1) sources and types of violence, including sexual, physical, and financial violence perpetrated by clients and police, (2) harm reduction strategies, including screening clients and safe work locations, receipt of payment before sexual act, and formation of an informal security network, and (3) recommendations on structural changes to reduce violence that emphasized sex work decriminalization and increased police accountability. As in other parts of the world, violence against FSWs is pervasive in Cameroon. Interventions targeting violence and HIV must address the forms of violence cited locally by FSWs and can build on FSWs' existing strengths and harm reduction strategies. Structural changes are needed to ensure access to justice for this population.

The Grammar of Violence

DEFF Research Database (Denmark)

Levisen, Carsten

2018-01-01

Abstract: This paper explores the Danish keyword vold ‘violence, abuse’ and its associated ethno-syntax. Calling into attention (i) the differences and similarities of violence-related concepts in ethnolinguistic communities, and (ii) the key role played by ethnosyntax in the elaboration...... of violence, vold, and similar concepts, the paper aims to open a new ethnolinguistic research agenda for the study of negative sociality constructs and the positive value system hidden in such concepts. The Danish ethnosyntax of vold ‘violence, abuse’ hidden in compound morphology is scrutinized. Focusing...

Violence against women.

Science.gov (United States)

1995-04-01

Domestic violence constitutes historical behavior in accord with patriarchal systems. Family and domestic violence includes female infanticide, higher female mortality, female genital mutilation, bride burning, rape, wife battering, and early marriage. These practices are commonly integrated into values and beliefs. Women accept domestic violence in violation of their basic human rights due to social prejudice and low self esteem. Mothers who perpetuate female genital mutilation believe that they are acting in the best interests of the child by adhering to centuries-long traditions. Women who allow female infanticide or female abortion are motivated to do so in order to maintain the security of their marriage. Women are in unequal power relationships and submit to their own detriment. Negative attitudes against women are perpetuated through incorrect interpretations of religious principles and myths. Economic self-reliance gives women the courage to stand up against domestic violence. Empowerment through education and appropriate and protective legislation also gives women the means to fight violence. Nongovernmental organizations (NGOs) at the national, regional, and international levels are active in creating awareness of domestic violence and influencing policy change. The NGO Working Group on Traditional Practices and the Inter-African Committee have a 10-year history of fighting against practices such as female genital mutilation. In order to bring about change, there must be cooperative and joint action among governmental and inter-governmental groups and NGOs.

Study on explosives and their quality performance

Energy Technology Data Exchange (ETDEWEB)

Nabiullah, M.; Pingua, B.M.P.; Jagdish Khan, M.; Emranuzzaman [Central Mining Research Institute, Dhanbad (India)

2005-07-01

There are about forty suppliers of explosive and blasting accessories in India manufacturing site mixed emulsion, site mixed slurry, ANFO, HANFO, packed products, and blasting accessories of use in surface and underground mines. A field laboratory was set up to measure explosive properties of explosive samples, cast booster, detonating fuse, detonators, cord relay, MS connector, and shock tubes. Density, velocity of detonation, water percentage, water resistance, and energy output were considered as the important properties of explosives. A rating system was designed for selection of good explosive products. The delay interval and delay scattering in cord relay and shock tube was studied to improve blast performance. This paper describes in detail the method of measurement and vender rating system for explosive products as per marking system accepted by Coal India. 12 refs., 4 figs., 22 tabs.

Explosive coalescence of Magnetic Islands

International Nuclear Information System (INIS)

Tajima, T.; Sakai, J.I.

1985-04-01

An explosive reconnection process associated with nonlinear evolution of the coalescence instability is found through studies of particle and magnetohydrodynamic simulations. The explosive coalescence is a self-similar process of magnetic collapse, in which the magnetic and electrostatic energies and temperatures explode toward the explosion time t 0 as (t 0 -t)/sup 8/3/,(t 0 -t) -4 , and (t 0 -t)/sup -8/3/, respectively. Ensuing amplitude oscillations in these quantities are identified by deriving an equation of motion for the scale factor in the Sagdeev potential

Screening sealed bottles for liquid explosives

Science.gov (United States)

Kumar, Sankaran; McMichael, W. Casey; Kim, Y.-W.; Sheldon, Alan G.; Magnuson, Erik E.; Ficke, L.; Chhoa, T. K.; Moeller, C. R.; Barrall, Geoffrey A.; Burnett, Lowell J.; Czipott, Peter V.; Pence, J. S.; Skvoretz, David C.

1997-01-01

A particularly disturbing development affecting transportation safety and security is the increasing use of terrorist devices which avoid detection by conventional means through the use of liquid explosives and flammables. The hazardous materials are generally hidden in wine or liquor bottles that cannot be opened routinely for inspection. This problem was highlighted by the liquid explosives threat which disrupted air traffic between the US an the Far East for an extended period in 1995. Quantum Magnetics has developed a Liquid Explosives Screening systems capable of scanning unopened bottles for liquid explosives. The system can be operated to detect specific explosives directly or to verify the labeled or bar-coded contents of the container. In this system, magnetic resonance (MR) is used to interrogate the liquid. MR produces an extremely rich data set and many characteristics of the MR response can be determined simultaneously. As a result, multiple MR signatures can be defined for any given set of liquids, and the signature complexity then selected according to the level of threat. The Quantum Magnetics Liquid Explosives Screening System is currently operational. Following extensive laboratory testing, a field trial of the system was carried out at the Los Angeles International Airport.

Hydrodynamics of Explosion Experiments and Models

CERN Document Server

Kedrinskii, Valery K

2005-01-01

Hydronamics of Explosion presents the research results for the problems of underwater explosions and contains a detailed analysis of the structure and the parameters of the wave fields generated by explosions of cord and spiral charges, a description of the formation mechanisms for a wide range of cumulative flows at underwater explosions near the free surface, and the relevant mathematical models. Shock-wave transformation in bubbly liquids, shock-wave amplification due to collision and focusing, and the formation of bubble detonation waves in reactive bubbly liquids are studied in detail. Particular emphasis is placed on the investigation of wave processes in cavitating liquids, which incorporates the concepts of the strength of real liquids containing natural microinhomogeneities, the relaxation of tensile stress, and the cavitation fracture of a liquid as the inversion of its two-phase state under impulsive (explosive) loading. The problems are classed among essentially nonlinear processes that occur unde...

Gas induced fire and explosion frequencies

International Nuclear Information System (INIS)

Coutts, D.A.

1997-01-01

The use and handling of flammable gases poses a fire and explosion hazard to many DOE nuclear facilities. This hazard is not unique to DOE facilities. Each year over 2,900 non-residential structural fires occur in the U.S. where a gas is the first item ignited. Details from these events are collected by the National Fire Incident Reporting System (NFIRS) through an extensive reporting network. This extensive data set (800,000 fires in non-residential structures over a 5-year period) is an underutilized resource within the DOE community. Explosions in nuclear facilities can have very severe consequences. The explosion can both damage the facility containment and provide a mechanism for significant radiological dispersion. In addition, an explosion can have significant worker safety implications. Because of this a quantitative frequency estimate for explosions in an SRS laboratory facility has been prepared using the NFIRS data. 6 refs., 1 tab

Child-to-Parent Violence: Challenging Perspectives on Family Violence

Science.gov (United States)

Coogan, Declan

2011-01-01

Until relatively recently, the focus of research, policy and intervention responses to abuse and violence within families has been almost exclusively on the behaviour of adults rather than on the violence within families carried out by children and adolescents. As a consequence, the aggressive and violent behaviour of children and adolescents at…

Conceptions About Social Violence and Violence Against Women: Community Participatory Diagnosis at Manchay, Lima.

Science.gov (United States)

Velázquez, Tesania; Fernández, Adriana

2015-01-01

This article is the result of a participatory diagnosis about social violence and violence against women carried out with both female and male inhabitants of San Pablo Mirador (SPM), an urban neighborhood located in the upper area of Manchay, Lima. It was requested by the nongovernmental organization (NGO) Ruwasunchis, and was carried out by a group of faculties and students of the Master Program in Community Psychology at the Pontificia Universidad Católica del Perú. This article reports the conceptions and the dynamics of social violence in SPM, specifically violence against women, and the resources used by its members in order to address this violence in the community.

[Violence in conjugal relations: concealing and taking sexual violence for granted].

Science.gov (United States)

Dantas-Berger, Sônia Maria; Giffin, Karen

2005-01-01

This article presents the results of a qualitative study of women who had filed complaints of domestic violence, situating gender relations in a broader context. The authors focus on the meaning ascribed to sexual coercion in violent relations, suggesting that conjugal sexual violence is related to the perverse effects of changes in the sexual division of labor and the aggravated double demands on women from housework and the workplace, in relation to the dismantling of the male's role as provider in situations of poverty. In this context, women's refusal to engage in sex (a form of resistance which expresses their desire to be sexual protagonists and communicates disappointment with their partners) can be seen as contributing to the exacerbation of conjugal violence. In their partial position of "subjects of resistance", these women reveal a situation of oppression which is rarely referred to as violence: feelings of disgust and repulsion following sexual relations conceded as "conjugal rights" are similar to those manifested by victims of rape by strangers (which, in contrast, is generally recognized as "sexual violence").

Importance of Gender and Attitudes about Violence in the Relationship between Exposure to Interparental Violence and the Perpetration of Teen Dating Violence

Science.gov (United States)

Temple, Jeff R.; Shorey, Ryan C.; Tortolero, Susan R.; Wolfe, David A.; Stuart, Gregory L.

2013-01-01

Objective: Mounting evidence has demonstrated a link between exposure to family of origin violence and the perpetration of teen dating violence (TDV). However, only recently have mechanisms underlying this relationship been investigated and very few studies have differentiated between exposure to father-to-mother and mother-to-father violence.…

[Violence towards pregnant women].

Science.gov (United States)

Kramek, J; Grzymała-Krzyzostaniak, A; Celewicz, Z; Ronin-Walknowska, E

2001-12-01

The aim of this work was the evaluation of the scale of violence towards pregnant women in the westpomeranian province, the definition of the social-biological profile of women exposed to violence and social-biological profile of their partners. The evaluation of the influence of violence on pregnant women's ending term and the weight of the newborns. 481 women were enrolled and an anonymous study was used in the form of questionnaires. A questionnaire was a modified form of a query-sheet proposed by WHO. 25% of the enrolled women were exposed to physical and psychological (emotional) abuse, 7.1% to psychical violence, women and men exposed to violence in their childhood more often become violent in their adult life. Men that physically abuse pregnant women are often of primary school education, are unemployed, drink alcohol and smoke. Physical abuse by a partner during pregnancy usually experience women with primary school education, who drink and smoke. Violence during pregnancy is usually associated with premature delivery as well as low birth weight of the newborns.

Safety problems with abandoned explosive facilities

International Nuclear Information System (INIS)

Courtright, W.C.

1969-01-01

Procedures were developed for the safe removal of explosive and radioactive contaminated materials structures and drains from abandoned sites, including explosives processing and service buildings with a goal to return the entire area to its natural state and to permit public access. The safety problems encountered in the cleanup and their solutions are applicable to modification and maintenance work in operating explosive facilities. (U.S.)

From early dating violence to adult intimate partner violence: Continuity and sources of resilience in adulthood.

Science.gov (United States)

Greenman, Sarah J; Matsuda, Mauri

2016-10-01

Previous literature has found continuity for intimate partner violence, but little research has explored continuity between dating violence and adult intimate partner violence (IPV) or whether protective factors may attenuate this relationship. This research hypothesised a positive relationship between dating violence in early adulthood and later adulthood IPV and that support and attachment would provide buffering and direct protection for this relationship. Data from the Rochester Youth Development Study were used to explore these questions through negative binomial regression. Dating violence was statistically significantly related to an increase of adult IPV. Family support, parental reports of attachment to the subject, peer support and parenting-related social support all were protective factors that provided a direct effect for those respondents perpetrating dating violence. None of the protective factors provided buffering protection between dating violence and adult IPV. Results confirm significant continuity between dating violence and IPV and that support from peers and family, parenting-related support and parental reports of attachment protect an individual from continuing to engage in intimate partner violence throughout adulthood. Bolstering these supportive relationships may help provide points of intervention to interrupt the link between early dating violence and later adulthood IPV. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Thermal Response Analyses of Spherical LPG Storage Tank

Energy Technology Data Exchange (ETDEWEB)

Chen, Hsijen.; Lin, Mannhsing.; Chao, Fuyuan

1999-02-01

Liquefied petroleum gas (LPG) is a very important fuel and chemical feed stock as well; however, the hydrocarbon has been involved in many major fires and explosions. One of these accidents is boiling-liquid, expanding-vapor explosion (BLEVE). It is a phenomenon that results from the sudden release form confinement of a liquid at a temperature above its atmospheric-pressure boiling point. The sudden decrease in pressure results in the explosive vaporization of a fraction of the liquid and a cloud of vapor and mist with the accompanying blast effects. Most BLEVEs involve flammable liquids, and most BELEVE releases are ignited by a surrounding fire and result in a fireball. The primary objective of this paper is to develop a computer model in order to determine the thermal response of a spherical LPG tank involved in fire engulfment accidents. The assessment of the safety spacing between tanks was also discussed. (author)

The Use of Violence in Media: Economics of Violence, the Ideological Violence of Media and an Evaluation in Retrospect of Cultivation Theory

OpenAIRE

Ömer ÖZER

2017-01-01

The main focus of this study is violence used in the media. Especially today for Turkey, the heavy use of violence in the media is an important problem. Indeed, the mass media coverage is loaded with violence. However, it is hard to say that so far there is enough research done on this issue. In the study, first, we showed that the researches done within the scope of effect problem do not provide adeaquate answers to the question of why media use so much violence. This is suitable fo...

Helping Children Exposed to Domestic Violence

Science.gov (United States)

... for Families - Vietnamese Spanish Facts for Families Guide Domestic Violence and Children No. 109; Updated April 2013 As ... each year. This kind of violence is called domestic violence or intimate partner violence. The US Department of ...

Problems and perspectives of domestic violence prevention

OpenAIRE

Kasperskis, Darius

2009-01-01

This paper will analyze the domestic violence prevention problems and perspectives. The goal of this work is to discuss the main domestic violence characteristics, analyze Lithuanian and international prevention means and offer suggestions to improve Lithuanian domestic violence prevention. This work consentrates on mens violence over women. The conseption of violence is analyzed – the general violence features in criminology and law literature are discussed, the main domestic violence forms ...

Obstetric Violence, Another Form of Violence Against Women. The Tenerife Case

OpenAIRE

Rodríguez Ramos, Paulo Adrían; Aguilera Ávila, Laura

2017-01-01

IntroductionThe subject of this study is Obstetric Violence (OV). OV is understood as the different ways in which pregnant women, or those who are going into labor, are controlled and oppressed. OV may be considered as another type of gender-based violence because its aim is to control and oppress women. Additionally, OV could be considered as institutional and symbolic violence.ObjectivesThe aim of this study is to discover whether new mothers in Tenerife are being subject to Obstetric Viole...

Key Injury and Violence Data

Science.gov (United States)

... Traumatic Brain Injury Violence Prevention Key Injury and Violence Data Recommend on Facebook Tweet Share Compartir Injuries ... of death among persons 1-44. Injury- and violence-related deaths are only part of the problem ...