Generation of control sequences for a pilot-disassembly system

Science.gov (United States)

Seliger, Guenther; Kim, Hyung-Ju; Keil, Thomas

2002-02-01

Closing the product and material cycles has emerged as a paradigm for industry in the 21st century. Disassembly plays a key role in a life cycle economy since it enables the recovery of resources. A partly automated disassembly system should adapt to a large variety of products and different degrees of devaluation. Also the amounts of products to be disassembled can vary strongly. To cope with these demands an approach to generate on-line disassembly control sequences will be presented. In order to react on these demands the technological feasibility is considered within a procedure for the generation of disassembly control sequences. Procedures are designed to find available and technologically feasible disassembly processes. The control system is formed by modularised and parameterised control units in the cell level within the entire control architecture. In the first development stage product and process analyses at the sample product washing machine were executed. Furthermore a generalized disassembly process was defined. Afterwards these processes were structured in primary and secondary functions. In the second stage the disassembly control at the technological level was investigated. Factors were the availability of the disassembly tools and the technological feasibility of the disassembly processes within the disassembly system. Technical alternative disassembly processes are determined as a result of availability of the tools and technological feasibility of processes. The fourth phase was the concept for the generation of the disassembly control sequences. The approach will be proved in a prototypical disassembly system.

Impact of different disassembly line balancing algorithms on the performance of dynamic kanban system for disassembly line

Science.gov (United States)

Kizilkaya, Elif A.; Gupta, Surendra M.

2005-11-01

In this paper, we compare the impact of different disassembly line balancing (DLB) algorithms on the performance of our recently introduced Dynamic Kanban System for Disassembly Line (DKSDL) to accommodate the vagaries of uncertainties associated with disassembly and remanufacturing processing. We consider a case study to illustrate the impact of various DLB algorithms on the DKSDL. The approach to the solution, scenario settings, results and the discussions of the results are included.

TFIIH and P-TEFb coordinate transcription with capping enzyme recruitment at specific genes in fission yeast.

Science.gov (United States)

Viladevall, Laia; St Amour, Courtney V; Rosebrock, Adam; Schneider, Susanne; Zhang, Chao; Allen, Jasmina J; Shokat, Kevan M; Schwer, Beate; Leatherwood, Janet K; Fisher, Robert P

2009-03-27

Cyclin-dependent kinases (CDKs) are subunits of transcription factor (TF) IIH and positive transcription elongation factor b (P-TEFb). To define their functions, we mutated the TFIIH-associated kinase Mcs6 and P-TEFb homologs Cdk9 and Lsk1 of fission yeast, making them sensitive to inhibition by bulky purine analogs. Selective inhibition of Mcs6 or Cdk9 blocks cell division, alters RNA polymerase (Pol) II carboxyl-terminal domain (CTD) phosphorylation, and represses specific, overlapping subsets of transcripts. At a common target gene, both CDKs must be active for normal Pol II occupancy, and Spt5-a CDK substrate and regulator of elongation-accumulates disproportionately to Pol II when either kinase is inhibited. In contrast, Mcs6 activity is sufficient-and necessary-to recruit the Cdk9/Pcm1 (mRNA cap methyltransferase) complex. In vitro, phosphorylation of the CTD by Mcs6 stimulates subsequent phosphorylation by Cdk9. We propose that TFIIH primes the CTD and promotes recruitment of P-TEFb/Pcm1, serving to couple elongation and capping of select pre-mRNAs.

TFIIH and P-TEFb Coordinate Transcription with Capping Enzyme Recruitment at Specific Genes in Fission Yeast

Science.gov (United States)

Viladevall, Laia; St. Amour, Courtney V.; Rosebrock, Adam; Schneider, Susanne; Zhang, Chao; Allen, Jasmina J.; Shokat, Kevan M.; Schwer, Beate; Leatherwood, Janet K.; Fisher, Robert P.

2009-01-01

Summary Cyclin-dependent kinases (CDKs) are subunits of transcription factor (TF) IIH and positive transcription elongation factor b (P-TEFb). To define their functions, we mutated the TFIIH-associated kinase Mcs6 and P-TEFb homologs Cdk9 and Lsk1 of fission yeast, making them sensitive to bulky purine analogs. Selective inhibition of Mcs6 or Cdk9 blocks cell division, alters RNA polymerase (Pol) II carboxyl-terminal domain (CTD) phosphorylation and represses specific, overlapping subsets of transcripts. At a common target gene, both CDKs must be active for normal Pol II occupancy, and Spt5—a CDK substrate and regulator of elongation—accumulates disproportionately to Pol II when either kinase is inhibited. In contrast, Mcs6 activity is sufficient, and necessary, to recruit the Cdk9/Pcm1 (mRNA cap methyltransferase) complex. In vitro, phosphorylation of the CTD by Mcs6 stimulates subsequent phosphorylation by Cdk9. We propose that TFIIH primes the CTD and promotes recruitment of P-TEFb/Pcm1, serving to couple elongation and capping of select pre-mRNAs. PMID:19328067

Multi-kanban mechanism for personal computer disassembly

Science.gov (United States)

Udomsawat, Gun; Gupta, Surendra M.; Kamarthi, Sagar V.

2004-12-01

The use of personal computers (PCs) continues to increase every year. According to a 1999 figure, 50 percent of all US households owned PCs, a figure that continues to rise every year. With continuous development of sophisticated software, PCs are becoming increasingly powerful. In addition, the price of a PC continues to steadily decline. Furthermore, the typical life of a PC in the workplace is approximately two to three years while in the home it is three to five years. As these PCs become obsolete, they are replaced and the old PCs are disposed of. It is estimated that between 14 and 20 million PCs are retired annually in the US. While 20 to 30% of the units may be resold, the others are discarded. These discards represent a significant potential source of lead for the waste stream. In some communities, waste cathode ray tubes (CRTs) represent the second largest source of lead in the waste stream after vehicular lead acid batteries. PCs are, therefore, not suitable for dumping in landfills. Besides, several components of a PC can be reused and then there are other valuable materials that can also be harvested. And with the advent of product stewardship, product recovery is the best solution for manufacturers. Disassembly line is perhaps the most suitable set up for disassembling PCs. However, planning and scheduling of disassembly on a disassembly line is complicated. In this paper, we discuss some of the complications including product arrival, demand arrival, inventory fluctuation and production control mechanisms. We then show how to overcome them by implementing a multi-kanban mechanism in the PC disassembly line setting. The multi-kanban mechanism relies on dynamic routing of kanbans according to the state of the system. We investigate the multi-kanban mechanism using simulation and demonstrate that this mechanism is superior to the traditional push system in terms of controlling the system"s inventory while maintaining a decent customer service level.

Multikanban model for disassembly line with demand fluctuation

Science.gov (United States)

Udomsawat, Gun; Gupta, Surendra M.; Al-Turki, Yousef A. Y.

2004-02-01

In recent years, the continuous growth in consumer waste and dwindling natural resources has seriously threatened the environment. Realizing this, several countries have passed regulations that force manufacturers not only to manufacture environmentally conscious products, but also to take back their used products from consumers so that the components and materials recovered from the products may be reused and/or recycled. Disassembly plays an important role in product recovery. A disassembly line is perhaps the most suitable setting for disassembly of products in large quantities. Because a disassembly line has a tendency to generate excessive inventory, employing a kanban system can reduce the inventory level and let the system run more efficiently. A disassembly line is quite different from an assembly line. For example, not only can the demand arrive at the last station, it can also arrive at any of the other stations in the system. The demand for a component on the disassembly line could fluctuate widely. In fact, there are many other complicating matters that need to be considered to implement the concept of kanbans in such an environment. In this paper, we discuss the complications that are unique to a disassembly line. We discuss the complications in utilizing the conventional production control mechanisms in a disassembly line setting. We then show how to overcome them by implementing kanbans in a disassembly line setting with demand fluctuation and introduce the concept of multi-kanban mechanism. We demonstrate its effectiveness using a simulation model. An example is presented to illustrate the concept.

Disassembly automation automated systems with cognitive abilities

CERN Document Server

Vongbunyong, Supachai

2015-01-01

This book presents a number of aspects to be considered in the development of disassembly automation, including the mechanical system, vision system and intelligent planner. The implementation of cognitive robotics increases the flexibility and degree of autonomy of the disassembly system. Disassembly, as a step in the treatment of end-of-life products, can allow the recovery of embodied value left within disposed products, as well as the appropriate separation of potentially-hazardous components. In the end-of-life treatment industry, disassembly has largely been limited to manual labor, which is expensive in developed countries. Automation is one possible solution for economic feasibility. The target audience primarily comprises researchers and experts in the field, but the book may also be beneficial for graduate students.

Ubiquitin ligase activity of TFIIH and the transcriptional response to DNA damage.

Science.gov (United States)

Takagi, Yuichiro; Masuda, Claudio A; Chang, Wei-Hau; Komori, Hirofumi; Wang, Dong; Hunter, Tony; Joazeiro, Claudio A P; Kornberg, Roger D

2005-04-15

Core transcription factor (TF) IIH purified from yeast possesses an E3 ubiquitin (Ub) ligase activity, which resides, at least in part, in a RING finger (RNF) domain of the Ssl1 subunit. Yeast strains mutated in the Ssl1 RNF domain are sensitive to ultraviolet (UV) light and to methyl methanesulfonate (MMS). This increased sensitivity to DNA-damaging agents does not reflect a deficiency in nucleotide excision repair. Rather, it correlates with reduced transcriptional induction of genes involved in DNA repair, suggesting that the E3 Ub ligase activity of TFIIH mediates the transcriptional response to DNA damage.

Recycling of electrical motors by automatic disassembly

Science.gov (United States)

Karlsson, Björn; Järrhed, Jan-Ove

2000-04-01

This paper presents a robotized workstation for end-of-life treatment of electrical motors with an electrical effect of about 1 kW. These motors can, for example, be found in washing machines and in industry. There are two main steps in the work. The first step is an inspection whereby the functionality of the motor is checked and classification either for re-use or for disassembly is done. In the second step the motors classified for disassembly are disassembled in a robotized automatic station. In the initial step measurements are performed during a start-up sequence of about 1 s. By measuring the rotation speed and the current and voltage of the three phases of the motor classification for either reuse or disassembly can be done. During the disassembly work, vision data are fused in order to classify the motors according to their type. The vision system also feeds the control system of the robot with various object co-ordinates, to facilitate correct operation of the robot. Finally, tests with a vision system and eddy-current equipment are performed to decide whether all copper has been removed from the stator.

Mathematical and Simulation Modelling of Moisture Diffusion Mechanism during Plastic IC Packages Disassembly

Directory of Open Access Journals (Sweden)

Peng Mou

2013-01-01

Full Text Available Reuse of plastic IC packages disassembled from printed circuit boards (PCBs has significant environmental benefits and economic value. The interface delamination caused by moisture diffusion is the main failure mode of IC packages during the disassembling process, which greatly reduces the reusability and reliability of disassembled IC packages. Exploring moisture diffusion mechanism is a prerequisite to optimize prebaking processes before disassembling that is an effective way to avoid the interface delamination. To this end, a computational model with variable boundary conditions is developed based on the different combination state of water in IC packages. The distribution characteristics and mechanism of moisture diffusion behavior are analyzed including the humidity distribution field and the relation among baking temperature, water loss rate, and baking time during baking process, and then the results are validated by FEA simulation based on the improved definition of relative moisture concentration. Baking under variable temperature is proposed and compared with the baking process and baking efficiency under constant temperature to find out the optimized baking parameters. Finally, a set of curves which indicate the relation between baking energy consumption and temperature are determined under actual industrial baking experiments, which could be used as references to develop industrial standards for PCB disassembling process.

Illustrating the disassembly of 3D models

KAUST Repository

Guo, Jianwei; Yan, Dongming; Li, Er; Dong, Weiming; Wonka, Peter; Zhang, Xiaopeng

2013-01-01

We present a framework for the automatic disassembly of 3D man-made models and the illustration of the disassembly process. Given an assembled 3D model, we first analyze the individual parts using sharp edge loops and extract the contact faces

Disassembly and removal of sodium instrumentation test loop

International Nuclear Information System (INIS)

Ishikawa, Okinobu; Onojima, Takamitu; Nagai, Keiichi

2000-07-01

In 1999, the Sodium Instrumentation Test Loop was disassembled and removed. This report describes the tasks and experiences obtained in removing sodium from a storage tank, disassembling, and cleansing components and related activities. Overall the disassembly, handling and cleansing tasks proceeded as planned and the activities were carried out efficiently and safely. Documentation of the process is meant to establish not only a procedure, but also a guideline for future similar tasks. (author)

The United States pit disassembly and conversion project -- Meeting the MOX fuel specification

International Nuclear Information System (INIS)

Nelson, T.O.; James, C.A.; Kolman, D.G.

1998-01-01

The US is actively involved in demonstrating the disassembly of nuclear weapons pits to an unclassified form readied for disposition. The MOX option is the most likely path forward for plutonium that originated from nuclear weapon pits. The US demonstration line for pit disassembly and conversion is known as ARIES, the advanced recovery and integrated extraction system. The ARIES demonstration line is being used to gather data in an integrated fashion of the technologies needed for pit disassembly and conversion. These activities include the following modules: pit bisection, hydride-dehydride, oxide conversion, canning, electrolytic decontamination, and nondestructive assay (NDA). Pit bisection swages in a pit in half. Hydride-dehydride converts the pit plutonium metal to an unclassified metal button. To convert the plutonium metal to an oxide the US is investigating a number of options. The primary oxide conversion approach involves variations of combining plutonium hydriding and subsequent oxidation. Another approach is to simply oxidize the metal under controlled conditions-direct metal oxidation (DMO). To remove the gallium from the plutonium oxide, a thermal distillation approach is being used. These pyrochemical approaches will substantially reduce the wastes produced for oxide conversion of weapon plutonium, compared to traditional aqueous processing. The packaging of either the plutonium metal or oxide to long term storage criteria involves the canning and electrolytic decontamination modules. The NDA suite of instruments is then used to assay the material in the containers, which enables international verification without the need to open the containers and repackage them. All of these processes are described

Methods for otpimum and near optimum disassembly sequencing

NARCIS (Netherlands)

Lambert, A.J.D.; Gupta, S.M.

2008-01-01

This paper considers disassembly sequencing problems subjected to sequence dependent disassembly costs. In practice, the methods for dealing with such problems rely mainly on metaheuristic and heuristic methods, which intrinsically generate suboptimum solutions. Exact methods are NP-hard and

Integrating Safeguards into the Pit Disassembly and Conversion Facility

International Nuclear Information System (INIS)

Clark, T.G.

2002-01-01

In September 2000, the United States and the Russian Federation entered into an agreement which stipulates each country will irreversibly transform 34 metric tons of weapons-grade plutonium into material which could not be used for weapon purposes. Supporting the Department of Energy's (DOE) program to dispose of excess nuclear materials, the Pit Disassembly and Conversion Facility (PDCF) is being designed and constructed to disassemble the weapon ''pits'' and convert the nuclear material to an oxide form for fabrication into reactor fuel at the separate Mixed Oxide Fuel Fabrication Facility. The PDCF design incorporates automation to the maximum extent possible to facilitate material safeguards, reduce worker dose, and improve processing efficiency. This includes provisions for automated guided vehicle movements for shipping containers, material transport via automated conveyor between processes, remote process control monitoring, and automated Nondestructive Assay product systems

An Intelligent Agent-Controlled and Robot-Based Disassembly Assistant

Science.gov (United States)

Jungbluth, Jan; Gerke, Wolfgang; Plapper, Peter

2017-09-01

One key for successful and fluent human-robot-collaboration in disassembly processes is equipping the robot system with higher autonomy and intelligence. In this paper, we present an informed software agent that controls the robot behavior to form an intelligent robot assistant for disassembly purposes. While the disassembly process first depends on the product structure, we inform the agent using a generic approach through product models. The product model is then transformed to a directed graph and used to build, share and define a coarse disassembly plan. To refine the workflow, we formulate “the problem of loosening a connection and the distribution of the work” as a search problem. The created detailed plan consists of a sequence of actions that are used to call, parametrize and execute robot programs for the fulfillment of the assistance. The aim of this research is to equip robot systems with knowledge and skills to allow them to be autonomous in the performance of their assistance to finally improve the ergonomics of disassembly workstations.

Nuclear fuel bundle disassembly and assembly tool

International Nuclear Information System (INIS)

Yates, J.; Long, J.W.

1975-01-01

A nuclear power reactor fuel bundle is described which has a plurality of tubular fuel rods disposed in parallel array between two transverse tie plates. It is secured against disassembly by one or more locking forks which engage slots in tie rods which position the transverse plates. Springs mounted on the fuel and tie rods are compressed when the bundle is assembled thereby maintaining a continual pressure against the locking forks. Force applied in opposition to the springs permits withdrawal of the locking forks so that one tie plate may be removed, giving access to the fuel rods. An assembly and disassembly tool facilitates removal of the locking forks when the bundle is to be disassembled and the placing of the forks during assembly of the bundle. (U.S.)

A symbolic methodology to improve disassembly process design.

Science.gov (United States)

Rios, Pedro; Blyler, Leslie; Tieman, Lisa; Stuart, Julie Ann; Grant, Ed

2003-12-01

Millions of end-of-life electronic components are retired annually due to the proliferation of new models and their rapid obsolescence. The recovery of resources such as plastics from these goods requires their disassembly. The time required for each disassembly and its associated cost is defined by the operator's familiarity with the product design and its complexity. Since model proliferation serves to complicate an operator's learning curve, it is worthwhile to investigate the benefits to be gained in a disassembly operator's preplanning process. Effective disassembly process design demands the application of green engineering principles, such as those developed by Anastas and Zimmerman (Environ. Sci. Technol. 2003, 37, 94A-101A), which include regard for product complexity, structural commonality, separation energy, material value, and waste prevention. This paper introduces the concept of design symbolsto help the operator more efficiently survey product complexity with respect to location and number of fasteners to remove a structure that is common to all electronics: the housing. With a sample of 71 different computers, printers, and monitors, we demonstrate that appropriate symbols reduce the total disassembly planning time by 13.2 min. Such an improvement could well make efficient the separation of plastic that would otherwise be destined for waste-to-energy or landfill. The symbolic methodology presented may also improve Design for Recycling and Design for Maintenance and Support.

Pit disassembly and conversion demonstration environmental assessment and research and development activities

International Nuclear Information System (INIS)

1998-08-01

A significant portion of the surplus plutonium is in the form of pits, a nuclear weapons component. Pits are composed of plutonium which is sealed in a metallic shell. These pits would need to be safely disassembled and permanently converted to an unclassified form that would be suitable for long-term disposition and international inspection. To determine the feasibility of an integrated pit disassembly and conversion system, a Pit Disassembly and Conversion Demonstration is proposed to take place at the Los Alamos National Laboratory (LANL). This demonstration would be done in existing buildings and facilities, and would involve the disassembly of up to 250 pits and conversion of the recovered plutonium to plutonium metal ingots and plutonium dioxide. This demonstration also includes the conversion of up to 80 kilograms of clean plutonium metal to plutonium dioxide because, as part of the disposition process, some surplus plutonium metal may be converted to plutonium dioxide in the same facility as the surplus pits. The equipment to be used for the proposed demonstration addressed in this EA would use some parts of the Advanced Recovery and Integrated Extraction System (ARIES) capability, other existing equipment/capacities, plus new equipment that was developed at other sites. In addition, small-scale R and D activities are currently underway as part of the overall surplus plutonium disposition program. These R and D activities are related to pit disassembly and conversion, MOX fuel fabrication, and immobilization (in glass and ceramic forms). They are described in Section 7.0. On May 16, 1997, the Office of Fissile Materials Disposition (MD) notified potentially affected states and tribes that this EA would be prepared in accordance with NEPA. This EA has been prepared to provide sufficient information for DOE to determine whether a Finding of No Significant Impact (FONSI) is warranted or whether an EIS must be prepared

Cleaning, disassembly, and requalification of the FFTF in vessel handling machine

International Nuclear Information System (INIS)

Coops, W.J.

1977-10-01

The Engineering Model In Vessel Handling Machine (IVHM) was successfully removed, cleaned, disassembled, inspected, reassembled and reinstalled into the sodium test vessel at Richland, Washington. This was the first time in the United States a full size operational sodium wetted machine has been cleaned by the water vapor nitrogen process and requalified for operation. The work utilized an atmospheric control system during removal, a tank type water vapor nitrogen cleaning system and an open ''hands on'' disassembly and assembly stand. Results of the work indicate the tools, process and equipment are adequate for the non-radioactive maintenance sequence. Additionally, the work proves that a machine of this complexity can be successfully cleaned, maintained and re-used without the need to replace a large percentage of the sodium wetted parts

DISA- a computer code for accident analysis of fast reactor during disassembly phase

International Nuclear Information System (INIS)

Yadav, R.D.S.; Gupta, H.P.

2005-01-01

Analysis of the hypothetical transients in fast rectors that result in the disassembly of the reactor generally consists of three phases. In the phase-l, some initiating event like control rod ejection, coolant pump failure etc. is assumed to have taken place which leads the reactor to prompt critical state where fuel melting, sodium voiding etc. take place. In fast reactor normally the fuel is not in the optimum shape and further positive reactivity may be introduced into the system due to fuel melting. Fuel slumping is assumed to take place in this phase. If prompt criticality is reached as a result of the first phase, then disassembly phase is assumed to start. In this phase the neutron transient is followed till it is terminated by the disassembly of the core which takes place due to generation of high pressure gradients and which lead the core material to move from more worth region to less worth region. Doppler feed back is taken into account and reactivity feedback due to material movement is calculated by solving the hydrodynamics equations. The third phase will calculate the effect of this transient on the reactor vessel and containment. A computer code DISA for fast reactor DISAssembly phase, which is similar to the well known code VENUS has been developed. (author)

Studies of fast reactor disassembly using a Bethe-Tait computer code

International Nuclear Information System (INIS)

Ludwig, J.C.

1978-10-01

The advantages of the fast reactor are given and the general design outlined. Loss of Flow and Transient Overpower faults are possible; the potential consequences of such incidents are analysed using a deterministic approach. The course of an incident is split into several stages; of these only predisassembly and disassembly are considered. Predisassembly computer codes are described in general, and several particular codes are examined in more detail, based on a literature survey. The results and implications of disassembly calculations using the code EXTRA are presented. Here, the effects of several factors, such as the presence of retained fission gases and possible restraints on fuel motion, are investigated. Some comparisons are made with published results from the VENUS-II disassembly code. A general conclusion is that under some circumstances, the yield predicted during disassembly is relatively insensitive to modelling assumptions, and a simple code such as EXTRA may prove adequate if explicit core displacements are not required. A major factor in determining the yield of the disassembly phase is confirmed as being the rate of reactivity insertion during disassembly, as predicted by a predisassembly code. (U.K.)

Illustrating the disassembly of 3D models

KAUST Repository

Guo, Jianwei

2013-06-11

We present a framework for the automatic disassembly of 3D man-made models and the illustration of the disassembly process. Given an assembled 3D model, we first analyze the individual parts using sharp edge loops and extract the contact faces between each pair of neighboring parts. The contact faces are then used to compute the possible moving directions of each part. We then present a simple algorithm for clustering the sets of the individual parts into meaningful sub-assemblies, which can be used for a hierarchical decomposition. We take the stability of sub-assemblies into account during the decomposition process by considering the upright orientation of the input models. Our framework also provides a user-friendly interface to enable the superimposition of the constraints for the decomposition. Finally, we visualize the disassembly process by generating an animated sequence. The experiments demonstrate that our framework works well for a variety of complex models. © 2013 Elsevier Ltd.

Coordination of substrate binding and ATP hydrolysis in Vps4-mediated ESCRT-III disassembly.

Science.gov (United States)

Davies, Brian A; Azmi, Ishara F; Payne, Johanna; Shestakova, Anna; Horazdovsky, Bruce F; Babst, Markus; Katzmann, David J

2010-10-01

ESCRT-III undergoes dynamic assembly and disassembly to facilitate membrane exvagination processes including multivesicular body (MVB) formation, enveloped virus budding, and membrane abscission during cytokinesis. The AAA-ATPase Vps4 is required for ESCRT-III disassembly, however the coordination of Vps4 ATP hydrolysis with ESCRT-III binding and disassembly is not understood. Vps4 ATP hydrolysis has been proposed to execute ESCRT-III disassembly as either a stable oligomer or an unstable oligomer whose dissociation drives ESCRT-III disassembly. An in vitro ESCRT-III disassembly assay was developed to analyze Vps4 function during this process. The studies presented here support a model in which Vps4 acts as a stable oligomer during ATP hydrolysis and ESCRT-III disassembly. Moreover, Vps4 oligomer binding to ESCRT-III induces coordination of ATP hydrolysis at the level of individual Vps4 subunits. These results suggest that Vps4 functions as a stable oligomer that acts upon individual ESCRT-III subunits to facilitate ESCRT-III disassembly.

Mathematical and Simulation Modelling of Moisture Diffusion Mechanism during Plastic IC Packages Disassembly

OpenAIRE

Peng Mou; Dong Xiang; Guanghong Duan

2013-01-01

Reuse of plastic IC packages disassembled from printed circuit boards (PCBs) has significant environmental benefits and economic value. The interface delamination caused by moisture diffusion is the main failure mode of IC packages during the disassembling process, which greatly reduces the reusability and reliability of disassembled IC packages. Exploring moisture diffusion mechanism is a prerequisite to optimize prebaking processes before disassembling that is an effective way to avoid the ...

Disassembly of JT-60 tokamak device and ancillary facilities for JT-60 tokamak

International Nuclear Information System (INIS)

Okano, Fuminori; Ichige, Hisashi; Miyo, Yasuhiko; Kaminaga, Atsushi; Sasajima, Tadayuki; Nishiyama, Tomokazu; Yagyu, Jun-ichi; Ishige, Youichi; Suzuki, Hiroaki; Komuro, Kenichi; Sakasai, Akira; Ikeda, Yoshitaka

2014-03-01

The disassembly of JT-60 tokamak device and its peripheral equipments, where the total weight was about 5400 tons, started in 2009 and accomplished in October 2012. This disassembly was required process for JT-60SA project, which is the Satellite Tokamak project under Japan-EU international corroboration to modify the JT-60 to the superconducting tokamak. This work was the first experience of disassembling a large radioactive fusion device based on Radiation Hazard Prevention Act in Japan. The cutting was one of the main problems in this disassembly, such as to cut the welded parts together with toroidal field coils, and to cut the vacuum vessel into two. After solving these problems, the disassembly completed without disaster and accident. This report presents the outline of the JT-60 disassembly, especially tokamak device and ancillary facilities for tokamak device. (author)

Movement and equipositioning of plasmids by ParA filament disassembly

DEFF Research Database (Denmark)

Ringgaard, Simon; van Zon, Jeroen; Howard, Martin

2009-01-01

, plasmids consistently migrate behind disassembling ParA cytoskeletal structures, suggesting that ParA filaments pull plasmids by depolymerization. The perpetual cycles of ParA assembly and disassembly result in continuous relocation of plasmids, which, on time averaging, results in equidistribution...

Desmosome Assembly and Disassembly Are Membrane Raft-Dependent

Science.gov (United States)

Faundez, Victor; Koval, Michael; Mattheyses, Alexa L.; Kowalczyk, Andrew P.

2014-01-01

Strong intercellular adhesion is critical for tissues that experience mechanical stress, such as the skin and heart. Desmosomes provide adhesive strength to tissues by anchoring desmosomal cadherins of neighboring cells to the intermediate filament cytoskeleton. Alterations in assembly and disassembly compromise desmosome function and may contribute to human diseases, such as the autoimmune skin blistering disease pemphigus vulgaris (PV). We previously demonstrated that PV auto-antibodies directed against the desmosomal cadherin desmoglein 3 (Dsg3) cause loss of adhesion by triggering membrane raft-mediated Dsg3 endocytosis. We hypothesized that raft membrane microdomains play a broader role in desmosome homeostasis by regulating the dynamics of desmosome assembly and disassembly. In human keratinocytes, Dsg3 is raft associated as determined by biochemical and super resolution immunofluorescence microscopy methods. Cholesterol depletion, which disrupts rafts, prevented desmosome assembly and adhesion, thus functionally linking rafts to desmosome formation. Interestingly, Dsg3 did not associate with rafts in cells lacking desmosomal proteins. Additionally, PV IgG-induced desmosome disassembly occurred by redistribution of Dsg3 into raft-containing endocytic membrane domains, resulting in cholesterol-dependent loss of adhesion. These findings demonstrate that membrane rafts are required for desmosome assembly and disassembly dynamics, suggesting therapeutic potential for raft targeting agents in desmosomal diseases such as PV. PMID:24498201

Accomplishment of JT-60U disassembly work dealing with radioactive components

International Nuclear Information System (INIS)

Ikeda, Yoshitaka

2015-01-01

The upgrade of the JT-60U to the superconducting tokamak 'JT-60SA' has been carried out to contribute the early realization of fusion energy by addressing key physics issues relevant for ITER and DEMO. Disassembly of the JT-60U tokamak was required so as to newly install the JT-60SA torus at the same position in the torus hall. The JT-60U tokamak was featured by the complicated and welded structure against the strong electromagnetic force, and by the radioactivation due to deuterium-deuterium (D-D) reactions of 1.5x10"2"0 (n) in total. Since this work was the first experience of disassembling a large radioactivated fusion device in Japan, careful preparations of disassembly activities, including treatment of the radioactivated materials and safety work, have been made. About 13,000 components with a total weight of more than 5,400 tonnes were removed from the torus hall and stored safely in storage facilities. All disassembly components were stored with recording the data such as dose rate, weight and kind of material, so as to apply the clearance level regulation in future. It was confirmed that the main radioactive material of the disassembly components was the stainless steel and that its dose rate was almost background level (∼0.1 μSv/h) at ∼10 m far from the vacuum vessel. It seems that the disassembly components with background dose level are in the clearance level. The assembly of JT-60SA tokamak has started in January 2013 after this disassembly of the JT-60U tokamak. (author)

Disassembly for remanufacturing: A systematic literature review, new model development and future research needs

Directory of Open Access Journals (Sweden)

Anjar Priyono

2016-11-01

Full Text Available Purpose: Disassembly is an important process that distinguishes remanufacturing from conventional manufacturing. It is a unique process that becomes focus of investigation from many scholars. Yet, most scholars investigate disassembly from technical and operational standpoint that lack of strategic perspective. This paper attempts to fill this gap by looking at disassembly from a strategic perspective by considering organisational characteristics, process choices and product attributes. To be more specific, this paper has three objectives. First, to gain understanding what has been done, and what need to be done in the field of disassembly in remanufacturing. Second, to conduct a systematic literature review for identifying the factors affecting disassembly for remanufacturing. Third, to propose a new model of disassembly for remanufacturing and also to provide avenues for future research. Design/methodology/approach: This study used a systematic literature review method. A series of steps were undertaken during the review. The study was started with determining the purpose of the study, selecting appropriate keywords, and reducing the selected papers using a number of criteria. A deeper analysis was carried out on the final paper that meets the criteria for this review. Findings: There are two main findings of this study. First, a list of factors affecting disassembly in remanufacturing is identified. The factors can be categorised into three groups: organisational factors, process choices and product attributes. Second, using factors that have been identified, a new model of disassembly process for remanufacturing is developed. Current studies only consider disassembly as a physical activity to break down products into components. In the new model, disassembly is viewed as a process that converts into into output, which consist of a series of steps. Research limitations/implications: The opportunities for future research include: the need to

Disassembly for remanufacturing: A systematic literature review, new model development and future research needs

International Nuclear Information System (INIS)

Priyono, A.; Ijomah, W.; Bititci, U.

2016-01-01

Purpose: Disassembly is an important process that distinguishes remanufacturing from conventional manufacturing. It is a unique process that becomes focus of investigation from many scholars. Yet, most scholars investigate disassembly from technical and operational standpoint that lack of strategic perspective. This paper attempts to fill this gap by looking at disassembly from a strategic perspective by considering organisational characteristics, process choices and product attributes. To be more specific, this paper has three objectives. First, to gain understanding what has been done, and what need to be done in the field of disassembly in remanufacturing. Second, to conduct a systematic literature review for identifying the factors affecting disassembly for remanufacturing. Third, to propose a new model of disassembly for remanufacturing and also to provide avenues for future research. Design/methodology/approach: This study used a systematic literature review method. A series of steps were undertaken during the review. The study was started with determining the purpose of the study, selecting appropriate keywords, and reducing the selected papers using a number of criteria. A deeper analysis was carried out on the final paper that meets the criteria for this review. Findings: There are two main findings of this study. First, a list of factors affecting disassembly in remanufacturing is identified. The factors can be categorised into three groups: organisational factors, process choices and product attributes. Second, using factors that have been identified, a new model of disassembly process for remanufacturing is developed. Current studies only consider disassembly as a physical activity to break down products into components. In the new model, disassembly is viewed as a process that converts into into output, which consist of a series of steps. Research limitations/implications: The opportunities for future research include: the need to develop an index of

Disassembly for remanufacturing: A systematic literature review, new model development and future research needs

Energy Technology Data Exchange (ETDEWEB)

Priyono, A.; Ijomah, W.; Bititci, U.

2016-07-01

Purpose: Disassembly is an important process that distinguishes remanufacturing from conventional manufacturing. It is a unique process that becomes focus of investigation from many scholars. Yet, most scholars investigate disassembly from technical and operational standpoint that lack of strategic perspective. This paper attempts to fill this gap by looking at disassembly from a strategic perspective by considering organisational characteristics, process choices and product attributes. To be more specific, this paper has three objectives. First, to gain understanding what has been done, and what need to be done in the field of disassembly in remanufacturing. Second, to conduct a systematic literature review for identifying the factors affecting disassembly for remanufacturing. Third, to propose a new model of disassembly for remanufacturing and also to provide avenues for future research. Design/methodology/approach: This study used a systematic literature review method. A series of steps were undertaken during the review. The study was started with determining the purpose of the study, selecting appropriate keywords, and reducing the selected papers using a number of criteria. A deeper analysis was carried out on the final paper that meets the criteria for this review. Findings: There are two main findings of this study. First, a list of factors affecting disassembly in remanufacturing is identified. The factors can be categorised into three groups: organisational factors, process choices and product attributes. Second, using factors that have been identified, a new model of disassembly process for remanufacturing is developed. Current studies only consider disassembly as a physical activity to break down products into components. In the new model, disassembly is viewed as a process that converts into into output, which consist of a series of steps. Research limitations/implications: The opportunities for future research include: the need to develop an index of

An Entropy-Based Adaptive Hybrid Particle Swarm Optimization for Disassembly Line Balancing Problems

Directory of Open Access Journals (Sweden)

Shanli Xiao

2017-11-01

Full Text Available In order to improve the product disassembly efficiency, the disassembly line balancing problem (DLBP is transformed into a problem of searching for the optimum path in the directed and weighted graph by constructing the disassembly hierarchy information graph (DHIG. Then, combining the characteristic of the disassembly sequence, an entropy-based adaptive hybrid particle swarm optimization algorithm (AHPSO is presented. In this algorithm, entropy is introduced to measure the changing tendency of population diversity, and the dimension learning, crossover and mutation operator are used to increase the probability of producing feasible disassembly solutions (FDS. Performance of the proposed methodology is tested on the primary problem instances available in the literature, and the results are compared with other evolutionary algorithms. The results show that the proposed algorithm is efficient to solve the complex DLBP.

A methodological approach for designing and sequencing product families in Reconfigurable Disassembly Systems

Directory of Open Access Journals (Sweden)

Ignacio Eguia

2011-10-01

Full Text Available Purpose: A Reconfigurable Disassembly System (RDS represents a new paradigm of automated disassembly system that uses reconfigurable manufacturing technology for fast adaptation to changes in the quantity and mix of products to disassemble. This paper deals with a methodology for designing and sequencing product families in RDS. Design/methodology/approach: The methodology is developed in a two-phase approach, where products are first grouped into families and then families are sequenced through the RDS, computing the required machines and modules configuration for each family. Products are grouped into families based on their common features using a Hierarchical Clustering Algorithm. The optimal sequence of the product families is calculated using a Mixed-Integer Linear Programming model minimizing reconfigurability and operational costs. Findings: This paper is focused to enable reconfigurable manufacturing technologies to attain some degree of adaptability during disassembly automation design using modular machine tools. Research limitations/implications: The MILP model proposed for the second phase is similar to the well-known Travelling Salesman Problem (TSP and therefore its complexity grows exponentially with the number of products to disassemble. In real-world problems, which a higher number of products, it may be advisable to solve the model approximately with heuristics. Practical implications: The importance of industrial recycling and remanufacturing is growing due to increasing environmental and economic pressures. Disassembly is an important part of remanufacturing systems for reuse and recycling purposes. Automatic disassembly techniques have a growing number of applications in the area of electronics, aerospace, construction and industrial equipment. In this paper, a design and scheduling approach is proposed to apply in this area. Originality/value: This paper presents a new concept called Reconfigurable Disassembly System

The effect of sudden server breakdown on the performance of a disassembly line

Science.gov (United States)

Udomsawat, Gun; Gupta, Surendra M.

2005-11-01

Product and material recovery relies on the disassembly process to separate target components or materials from the end-of-life (EOL) products. Disassembly line is especially effective when products in large quantity are disassembled. Unlike an assembly line, a disassembly line is more complex and is subjected to numerous uncertainties including stochastic and multi-level arrivals of component demands, stochastic arrival times for EOL products, and process interruption due to equipment failure. These factors seriously impair the control mechanism in the disassembly line. A common production control mechanism is the traditional push system (TPS). TPS responds to the aforementioned complications by carrying substantial amounts of inventories. An alternative control mechanism is a newly developed multi-kanban pull system (MKS) that relies on dynamic routing of kanbans, which tends to minimize the system's inventories while maintaining demand serviceability. In this paper we explore the impact of sudden breakdown of server on the performance of a disassembly line. We compare the overall performances of the TPS and MKS by considering two scenarios. We present the solution procedure and results for these cases.

Design for Disassembly

DEFF Research Database (Denmark)

Beim, Anne

2018-01-01

‘Design for Disassembly’ is becoming a familiar part of discourses on environmental strategies for construction and sustainable design. The concept originates in industrial design and pertains to a wide range of strategies for reuse and recycling, all of which highlight a whole-of-life approach t...... to materials and buildings. Design for Disassembly is particularly relevant to prefabricated and industrialized construction; as such methodologies already contain within them the possibility for easy deconstruction, whether for maintenance, refurbishment or reuse....

p44 and p34 subunits of the BTF2/TFIIH transcription factor have homologies with SSL1, a yeast protein involved in DNA repair.

NARCIS (Netherlands)

S. Humbert; H. van Vuuren; Y. Lutz; J.H.J. Hoeijmakers (Jan); J-M. Egly (Jean-Marc); V. Moncollin

1994-01-01

textabstractThe human BTF2 (TFIIH) transcription factor is a multisubunit protein involved in transcription initiation by RNA polymerase II (B) as well as in DNA repair. In addition to the previously characterized p62 and p89/ERCC3 subunits, we have cloned two other subunits of BTF2, p44 and p34.

Application of industrial robots in automatic disassembly line of waste LCD displays

Science.gov (United States)

Wang, Sujuan

2017-11-01

In the automatic disassembly line of waste LCD displays, LCD displays are disassembled into plastic shells, metal shields, circuit boards, and LCD panels. Two industrial robots are used to cut metal shields and remove circuit boards in this automatic disassembly line. The functions of these two industrial robots, and the solutions to the critical issues of model selection, the interfaces with PLCs and the workflows were described in detail in this paper.

Low cytoplasmic pH reduces ER-Golgi trafficking and induces disassembly of the Golgi apparatus

Energy Technology Data Exchange (ETDEWEB)

Soonthornsit, Jeerawat [Laboratory for Cell and Developmental Biology, Department of Molecular Biosciences, Faculty of Life Sciences, Kyoto Sangyo University, Motoyama, Kamigamo, Kita, Kyoto 603-8555 (Japan); Yamaguchi, Yoko; Tamura, Daisuke [Division of Life Sciences, Graduate School of Natural Science and Technology, Kanazawa University, Kakuma, Kanazawa 920-1192 (Japan); Ishida, Ryuichi; Nakakoji, Yoko; Osako, Shiho [Laboratory for Cell and Developmental Biology, Department of Molecular Biosciences, Faculty of Life Sciences, Kyoto Sangyo University, Motoyama, Kamigamo, Kita, Kyoto 603-8555 (Japan); Yamamoto, Akitsugu [Department of Animal Bioscience, Nagahama Institute of Bio-Science and Technology, 266 Tamura, Nagahama, Shiga, 526‐0829 (Japan); Nakamura, Nobuhiro, E-mail: osaru3@cc.kyoto-su.ac.jp [Laboratory for Cell and Developmental Biology, Department of Molecular Biosciences, Faculty of Life Sciences, Kyoto Sangyo University, Motoyama, Kamigamo, Kita, Kyoto 603-8555 (Japan); Division of Life Sciences, Graduate School of Natural Science and Technology, Kanazawa University, Kakuma, Kanazawa 920-1192 (Japan)

2014-11-01

The Golgi apparatus was dramatically disassembled when cells were incubated in a low pH medium. The cis-Golgi disassembled quickly, extended tubules and spread to the periphery of cells within 30 min. In contrast, medial- and trans-Golgi were fragmented in significantly larger structures of smaller numbers at a slower rate and remained largely in structures distinct from the cis-Golgi. Electron microscopy revealed the complete disassembly of the Golgi stack in low pH treated cells. The effect of low pH was reversible; the Golgi apparatus reassembled to form a normal ribbon-like structure within 1–2 h after the addition of a control medium. The anterograde ER to Golgi transport and retrograde Golgi to ER transport were both reduced under low pH. Phospholipase A{sub 2} inhibitors (ONO, BEL) effectively suppressed the Golgi disassembly, suggesting that the phospholipase A{sub 2} was involved in the Golgi disassembly. Over-expression of Rab1, 2, 30, 33 and 41 also suppressed the Golgi disassembly under low pH, suggesting that they have protective role against Golgi disassembly. Low pH treatment reduced cytoplasmic pH, but not the luminal pH of the Golgi apparatus, strongly suggesting that reduction of the cytoplasmic pH triggered the Golgi disassembly. Because a lower cytoplasmic pH is induced in physiological or pathological conditions, disassembly of the Golgi apparatus and reduction of vesicular transport through the Golgi apparatus may play important roles in cell physiology and pathology. Furthermore, our findings indicated that low pH treatment can serve as an important tool to analyze the molecular mechanisms that support the structure and function of the Golgi apparatus. - Highlights: • The Golgi apparatus reversibly disassembles by low pH treatment. • The cis-Golgi disassembles quickly generating tubular structures. • Both anterograde and retrograde transport between the ER and the Golgi apparatus are reduced. • Phospholipase A{sub 2} inhibitors (ONO

Development of remote disassembly technology for liquid-metal reactor (LMR) fuel

International Nuclear Information System (INIS)

Bradley, E.C.; Evans, J.H.; Metz, C.F. III; Weil, B.S.

1990-01-01

A major objective of the Consolidated Fuel Reprocessing Program (CFRP) is to develop equipment and demonstrate technology to reprocess fast breeder reactor fuel. Experimental work on fuel disassembly cutting methods began in the 1970s. High-power laser cutting was selected as the preferred cutting method for fuel disassembly. Remotely operated development equipment was designed, fabricated, installed, and tested at Oak Ridge National Laboratory (ORNL). Development testing included remote automatic operation, remote maintenance testing, and laser cutting process development. This paper summarizes the development work performed at ORNL on remote fuel disassembly. 2 refs., 1 fig

Disassembly Properties of Cementitious Finish Joints Using an Induction Heating Method

Science.gov (United States)

Ahn, Jaecheol; Noguchi, Takafumi; Kitagaki, Ryoma

2015-01-01

Efficient maintenance and upgrading of a building during its lifecycle are difficult because a cementitious finish uses materials and parts with low disassembly properties. Additionally, the reuse and recycling processes during building demolition also present numerous problems from the perspective of environmental technology. In this study, an induction heating (IH) method was used to disassemble cementitious finish joints, which are widely used to join building members and materials. The IH rapidly and selectively heated and weakened these joints. The temperature elevation characteristics of the cementitious joint materials were measured as a function of several resistor types, including wire meshes and punching metals, which are usually used for cementitious finishing. The disassembly properties were evaluated through various tests using conductive resistors in cementitious joints such as mortar. When steel fiber, punching metal, and wire mesh were used as conductive resistors, the cementitious modifiers could be weakened within 30 s. Cementitious joints with conductive resistors also showed complete disassembly with little residual bond strength.

Spent fuel disassembly and canning programs at the Barnwell Nuclear Fuel Plant (BNFP)

International Nuclear Information System (INIS)

Townes, G.A.

1979-10-01

Methods of disassembling and canning spent fuel to allow more efficient storage are being investigated at the BNFP. Studies and development programs are aimed at dry disassembly of fuel to allow storage and shipment of fuel pins rather than full fuel assemblies. Results indicate that doubling existing storage capacity or tripling the carrying capacity of existing transportation equipment is achievable. Disassembly could be performed in the BNFP hot cells at rates of about 12 to 15 assemblies per day

Hybrid disassembly system for cellular telephone end-of-life treatment

Energy Technology Data Exchange (ETDEWEB)

Kniebel, M.; Basdere, B.; Seliger, G. [Technical Univ. Berlin, Inst. for Machine Tools and Factory Management, Dept. of Assembly Technology and Factory Management, Berlin (Germany)

2004-07-01

Concern over the negative environmental impacts associated with the production, use, and end-of-life (EOL) of cellular telephones is particularly high due to large production volumes and characteristically short time scales of technological and stylistic obsolescence. Landfilled or incinerated cellular telephones create the potential for release of toxic substances. The European legislation has passed the directive on Waste of Electrical and Electronic Equipment (WEEE) to regulate their collection and appropriate end-of-life treatment. Manufacturers must conduct material recycling or remanufacturing processes to recover resources. While recovery rates can hardly be met economically by material recycling, remanufacturing and reusing cellular phones is developing into a reasonable alternative. Both end-of-life options require disassembly processes for WEEE compliant treatment. Due to the high number of different cell phone variants and their typical design that fits components into tight enclosing spaces, cellular phone disassembly becomes a challenging task. These challenges and the expected high numbers of phones to be returned in the course of the WEEE urges for automated disassembly. A hybrid disassembly system has been developed to ensure the mass-treatment of obsolete cellular phones. It has been integrated into a prototypical remanufacturing factory for cellular phones that has been planned based on market data. (orig.)

Low cytoplasmic pH reduces ER-Golgi trafficking and induces disassembly of the Golgi apparatus.

Science.gov (United States)

Soonthornsit, Jeerawat; Yamaguchi, Yoko; Tamura, Daisuke; Ishida, Ryuichi; Nakakoji, Yoko; Osako, Shiho; Yamamoto, Akitsugu; Nakamura, Nobuhiro

2014-11-01

The Golgi apparatus was dramatically disassembled when cells were incubated in a low pH medium. The cis-Golgi disassembled quickly, extended tubules and spread to the periphery of cells within 30 min. In contrast, medial- and trans-Golgi were fragmented in significantly larger structures of smaller numbers at a slower rate and remained largely in structures distinct from the cis-Golgi. Electron microscopy revealed the complete disassembly of the Golgi stack in low pH treated cells. The effect of low pH was reversible; the Golgi apparatus reassembled to form a normal ribbon-like structure within 1-2h after the addition of a control medium. The anterograde ER to Golgi transport and retrograde Golgi to ER transport were both reduced under low pH. Phospholipase A2 inhibitors (ONO, BEL) effectively suppressed the Golgi disassembly, suggesting that the phospholipase A2 was involved in the Golgi disassembly. Over-expression of Rab1, 2, 30, 33 and 41 also suppressed the Golgi disassembly under low pH, suggesting that they have protective role against Golgi disassembly. Low pH treatment reduced cytoplasmic pH, but not the luminal pH of the Golgi apparatus, strongly suggesting that reduction of the cytoplasmic pH triggered the Golgi disassembly. Because a lower cytoplasmic pH is induced in physiological or pathological conditions, disassembly of the Golgi apparatus and reduction of vesicular transport through the Golgi apparatus may play important roles in cell physiology and pathology. Furthermore, our findings indicated that low pH treatment can serve as an important tool to analyze the molecular mechanisms that support the structure and function of the Golgi apparatus. Copyright © 2014 Elsevier Inc. All rights reserved.

Microcanonical simulation of nuclear disassembly

International Nuclear Information System (INIS)

Koonin, S.E.; Randrup, J.

1986-01-01

There is considerable interest in the disassembly of the hot nuclear matter produced in high-energy nuclear collisions. A particular stimulus has been the prospect of observing a nuclear liquid-gas phase transition. On rather general grounds, such a transition is expected to occur in nuclear matter at subsaturation densities with temperatures of 10-20 MeV. However, virtually all previous discussions of this phenomenon have been based on thermodynamical considerations valid for infinite, non-interacting systems and the qualitative validity of the results has not been ascertained for the relatively small, finite, interacting systems of practical relevance. Nor is it clear how the occurrence of the phase transition will manifest itself in the asymptotically observed fragment distribution. To progress in these matters, the authors have formulated a microcanonical simulation of the disassembly process, including interfragment interactions. It is a natural refinement of the grand canonical model first presented in [1] and further developed in [2] and is also a exact version of the model developed in [3] for the generation of complete multifragment events in medium-energy collisions. In this contribution, the authors give a brief description of the key ingredients in the model and its numerical implementation

Effects of reactive oxygen species on cellular wall disassembly of banana fruit during ripening.

Science.gov (United States)

Cheng, Guiping; Duan, Xuewu; Shi, John; Lu, Wangjin; Luo, Yunbo; Jiang, Weibo; Jiang, Yueming

2008-07-15

Fruit softening is generally attributed to cell wall disassembly. Experiments were conducted to investigate effects of various reactive oxygen species (ROS) on in vitro cellular wall disassembly of harvested banana fruit. The alcohol-extracted insoluble residue (AEIR) was obtained from the pulp tissues of banana fruit at various ripening stages and then used to examine the disassembly of cellular wall polysaccharides in the presence of superoxide anion (O2(-)), hydrogen peroxide (H2O2) or hydroxyl radical (OH) and their scavengers. The presence of OH accelerated significantly disassembly of cellular wall polysaccharides in terms of the increase in contents of total sugars released and uronic acid, and the decrease in molecular mass of soluble polysaccharides, using gel permeation chromatography. However, the treatment with H2O2 or O2(-) showed no significant effect on the disassembly of cellular wall polysaccharides. Furthermore, the degradation of the de-esterified AEIR was more susceptible to OH attack than the esterified AEIR. In addition, the effect of OH could be inhibited in the presence of OH scavenger. This study suggests that disassembly of cellular wall polysaccharides could be initiated by OH as the solublisation of the polysaccharides increased, which, in turn, accelerated fruit softening. Copyright © 2008 Elsevier Ltd. All rights reserved.

Meiotic Clade AAA ATPases: Protein Polymer Disassembly Machines.

Science.gov (United States)

Monroe, Nicole; Hill, Christopher P

2016-05-08

Meiotic clade AAA ATPases (ATPases associated with diverse cellular activities), which were initially grouped on the basis of phylogenetic classification of their AAA ATPase cassette, include four relatively well characterized family members, Vps4, spastin, katanin and fidgetin. These enzymes all function to disassemble specific polymeric protein structures, with Vps4 disassembling the ESCRT-III polymers that are central to the many membrane-remodeling activities of the ESCRT (endosomal sorting complexes required for transport) pathway and spastin, katanin p60 and fidgetin affecting multiple aspects of cellular dynamics by severing microtubules. They share a common domain architecture that features an N-terminal MIT (microtubule interacting and trafficking) domain followed by a single AAA ATPase cassette. Meiotic clade AAA ATPases function as hexamers that can cycle between the active assembly and inactive monomers/dimers in a regulated process, and they appear to disassemble their polymeric substrates by translocating subunits through the central pore of their hexameric ring. Recent studies with Vps4 have shown that nucleotide-induced asymmetry is a requirement for substrate binding to the pore loops and that recruitment to the protein lattice via MIT domains also relieves autoinhibition and primes the AAA ATPase cassettes for substrate binding. The most striking, unifying feature of meiotic clade AAA ATPases may be their MIT domain, which is a module that is found in a wide variety of proteins that localize to ESCRT-III polymers. Spastin also displays an adjacent microtubule binding sequence, and the presence of both ESCRT-III and microtubule binding elements may underlie the recent findings that the ESCRT-III disassembly function of Vps4 and the microtubule-severing function of spastin, as well as potentially katanin and fidgetin, are highly coordinated. Copyright © 2015 Elsevier Ltd. All rights reserved.

Capillarity-induced disassembly of virions in carbon nanotubes

Energy Technology Data Exchange (ETDEWEB)

Fan Xiaobin; Peng Wenchao; Li Yang; Li Xianyu; Zhang Guoliang; Zhang Fengbao [School of Chemical Engineering and Technology, Tianjin University, Tianjin (China); Barclay, J Elaine; Evans, David J [Department of Biological Chemistry, John Innes Centre, Norwich Research Park, Norwich NR4 7UH (United Kingdom)], E-mail: fbzhang@tju.edu.cn

2008-04-23

Studying the transport and fate of viruses through nanochannels is of great importance. By using the nanochannel of a carbon nanotube (CNT) as an ideal model, we evaluated the possibility of capillarity-induced viral transport through a closely fitting nanochannel and explored the mechanisms involved. It is shown both experimentally and theoretically that Cowpea mosaic virus can enter CNTs by capillarity. However, when introduced into a nanotube the protein capsid may disassemble. During the initial capillary filling stage, anomalous needle-shaped high pressure exists in the centre of the nanotube's entrance. This high pressure, combining with the significant negative pressure within the nanotube, may account for the disassembly of the virions.

A Label Correcting Algorithm for Partial Disassembly Sequences in the Production Planning for End-of-Life Products

Directory of Open Access Journals (Sweden)

Pei-Fang (Jennifer Tsai

2012-01-01

Full Text Available Remanufacturing of used products has become a strategic issue for cost-sensitive businesses. Due to the nature of uncertain supply of end-of-life (EoL products, the reverse logistic can only be sustainable with a dynamic production planning for disassembly process. This research investigates the sequencing of disassembly operations as a single-period partial disassembly optimization (SPPDO problem to minimize total disassembly cost. AND/OR graph representation is used to include all disassembly sequences of a returned product. A label correcting algorithm is proposed to find an optimal partial disassembly plan if a specific reusable subpart is retrieved from the original return. Then, a heuristic procedure that utilizes this polynomial-time algorithm is presented to solve the SPPDO problem. Numerical examples are used to demonstrate the effectiveness of this solution procedure.

Shape memory polymer nanocomposites for application of multiple-field active disassembly: experiment and simulation.

Science.gov (United States)

Carrell, John; Zhang, Hong-Chao; Wang, Shiren; Tate, Derrick

2013-11-19

Active disassembly (AD) uses innovative materials that can perform a designed disassembly action by the application of an external field. AD provides improvements over current disassembly processes by limiting machine or manual labor and enabling batch processing for end-of-life products. With improved disassembly operations, more reuse of components and purer recycling streams may be seen. One problem with AD, however, has been with the single-field actuation because of the probability of accidental disassembly. This presentation will discuss the application of shape memory polymer (SMP) nanocomposites in a new AD process. This novel AD process requires multiple-field actuation of the SMP nanocomposite fastener. In the analysis of this AD process, thermal and magnetic field tests were performed on the SMP nanocomposite. From these tests, finite-element analysis was performed to model and simulate the multiple-field AD process. The results of the simulations provide performance variables for the AD process and show a better performance time for the SMP nanocomposite fastener than for a comparable SMP fastener.

Out pile test of a disassembly tool for the intermediate examination of nuclear fuel rods

International Nuclear Information System (INIS)

Hong, Jintae; Joung, Chang-Young; Ahn, Sung-Ho; Yang, Tae-Ho; Jang, Seo-Yoon; Park, Seung-Jae

2016-01-01

The two fuel rod assemblies are assembled with a bayonet coupler, and the non-instrumented fuel rod assembly can be disassembled for intermediate examination. A tool to disassemble the non-instrumented fuel rod assembly from the test rig was developed, and steel wires are connected to the tool to operate release function. In this study, an assembly plug with a quick plug typed bayonet coupler and the accompanying disassembly tool was designed to prevent the interference problem. A test rig mockup was fabricated, and performance test was carried out in the laboratory. And, the out pile test was also carried out in the single channel test loop established in the KAERI. In this study, a modified coupler design to disassemble the non-instrumented fuel rod assembly from the test rig for the intermediate examination was suggested to solve interference problem of previous design. The performance of the modified design was verified by test mockup fabricated with the modified coupler design and accompanied disassembly tool design. Finally, out pile test was carried out in the single channel test loop in the KAERI, and the test rig and the disassembly tool showed good performance and reliability. The developed technique will be useful to the periodic intermediate examination of nuclear fuel rods

Out pile test of a disassembly tool for the intermediate examination of nuclear fuel rods

Energy Technology Data Exchange (ETDEWEB)

Hong, Jintae; Joung, Chang-Young; Ahn, Sung-Ho; Yang, Tae-Ho; Jang, Seo-Yoon; Park, Seung-Jae [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

The two fuel rod assemblies are assembled with a bayonet coupler, and the non-instrumented fuel rod assembly can be disassembled for intermediate examination. A tool to disassemble the non-instrumented fuel rod assembly from the test rig was developed, and steel wires are connected to the tool to operate release function. In this study, an assembly plug with a quick plug typed bayonet coupler and the accompanying disassembly tool was designed to prevent the interference problem. A test rig mockup was fabricated, and performance test was carried out in the laboratory. And, the out pile test was also carried out in the single channel test loop established in the KAERI. In this study, a modified coupler design to disassemble the non-instrumented fuel rod assembly from the test rig for the intermediate examination was suggested to solve interference problem of previous design. The performance of the modified design was verified by test mockup fabricated with the modified coupler design and accompanied disassembly tool design. Finally, out pile test was carried out in the single channel test loop in the KAERI, and the test rig and the disassembly tool showed good performance and reliability. The developed technique will be useful to the periodic intermediate examination of nuclear fuel rods.

Preliminary topical report on comparison reactor disassembly calculations

International Nuclear Information System (INIS)

McLaughlin, T.P.

1975-11-01

Preliminary results of comparison disassembly calculations for a representative LMFBR model (2100-l voided core) and arbitrary accident conditions are described. The analytical methods employed were the computer programs: FX2-POOL, PAD, and VENUS-II. The calculated fission energy depositions are in good agreement, as are measures of the destructive potential of the excursions, kinetic energy, and work. However, in some cases the resulting fuel temperatures are substantially divergent. Differences in the fission energy deposition appear to be attributable to residual inconsistencies in specifying the comparison cases. In contrast, temperature discrepancies probably stem from basic differences in the energy partition models inherent in the codes. Although explanations of the discrepancies are being pursued, the preliminary results indicate that all three computational methods provide a consistent, global characterization of the contrived disassembly accident

Status of the pit disassembly and conversion facility

International Nuclear Information System (INIS)

Wood, Warren T.; Christensen, Lowell T.

2000-01-01

A planned new facility, the Pit Disassembly and Conversion Facility (PDCF), will be used to disassemble the nation's inventory of surplus nuclear weapons pits and convert the plutonium from those pits into a form suitable for storage, international inspection, and final disposition. Sized to handle 35 metric tons of plutonium from pits and other sources over its 10-year operating life, the PDCF will apply the Advanced Recovery and Integrated Extraction System (ARIES) technology. ARIES process technology has been developed at Los Alamos National Laboratory (LANL) and Lawrence Livermore National Laboratory (LLNL), and an integrated system is being demonstrated at LANL. The Los Alamos National Laboratory is the lead for technical design oversight of the PDCF. Technical data gained from the ARIES demonstrations is integral for the proper design of the PDCF

Centralized disassembly and packaging of spent fuel in the DOE spent fuel management system

International Nuclear Information System (INIS)

Johnson, E.R.

1986-01-01

In October 1984, E.R. Johnson Associates, Inc. (JAI) initiated a study of the prospective use of a centralized facility for the disassembly and packaging of spent fuel to support the various elements of the US Dept. of Energy (DOE) spent fuel management system, including facilities for monitored retrievable storage (MRS) and repositories. It was DOE's original plan to receive spent fuel at each repository where it would be disassembled and packaged (overpacked) for disposal purposes. Subsequently, DOE considered the prospective use of MRS of spent fuel as an option for providing safe and reliable management of spent fuel. This study was designed to consider possible advantages of the use of centralized facilities for disassembly and packaging of spent fuel at whose location storage facilities could be added as required. The study was divided into three principal technical tasks that covered: (a) development of requirements and criteria for the central disassembly and packaging facility and associated systems. (2) Development of conceptual designs for the central disassembly and packaging facility and associated systems. (3) Estimation of capital and operating costs involved for all system facilities and determination of life cycle costs for various scenarios of operation - for comparison with the reference system

Phosphatase PP2A and microtubule-mediated pulling forces disassemble centrosomes during mitotic exit

Directory of Open Access Journals (Sweden)

Stephen J. Enos

2018-01-01

Full Text Available Centrosomes are microtubule-nucleating organelles that facilitate chromosome segregation and cell division in metazoans. Centrosomes comprise centrioles that organize a micron-scale mass of protein called pericentriolar material (PCM from which microtubules nucleate. During each cell cycle, PCM accumulates around centrioles through phosphorylation-mediated assembly of PCM scaffold proteins. During mitotic exit, PCM swiftly disassembles by an unknown mechanism. Here, we used Caenorhabditis elegans embryos to determine the mechanism and importance of PCM disassembly in dividing cells. We found that the phosphatase PP2A and its regulatory subunit SUR-6 (PP2ASUR-6, together with cortically directed microtubule pulling forces, actively disassemble PCM. In embryos depleted of these activities, ∼25% of PCM persisted from one cell cycle into the next. Purified PP2ASUR-6 could dephosphorylate the major PCM scaffold protein SPD-5 in vitro. Our data suggest that PCM disassembly occurs through a combination of dephosphorylation of PCM components and force-driven fragmentation of the PCM scaffold.

Direct measurement of conformational strain energy in protofilaments curling outward from disassembling microtubule tips.

Science.gov (United States)

Driver, Jonathan W; Geyer, Elisabeth A; Bailey, Megan E; Rice, Luke M; Asbury, Charles L

2017-06-19

Disassembling microtubules can generate movement independently of motor enzymes, especially at kinetochores where they drive chromosome motility. A popular explanation is the 'conformational wave' model, in which protofilaments pull on the kinetochore as they curl outward from a disassembling tip. But whether protofilaments can work efficiently via this spring-like mechanism has been unclear. By modifying a previous assay to use recombinant tubulin and feedback-controlled laser trapping, we directly demonstrate the spring-like elasticity of curling protofilaments. Measuring their mechanical work output suggests they carry ~25% of the energy of GTP hydrolysis as bending strain, enabling them to drive movement with efficiency similar to conventional motors. Surprisingly, a β-tubulin mutant that dramatically slows disassembly has no effect on work output, indicating an uncoupling of disassembly speed from protofilament strain. These results show the wave mechanism can make a major contribution to kinetochore motility and establish a direct approach for measuring tubulin mechano-chemistry.

Improved Nondestructive Disassembly Process using Augmented Reality and RFID Product/Part Tracking

Directory of Open Access Journals (Sweden)

Ile Mircheski

2017-11-01

Full Text Available The waste from electric and electronic equipment and discarded automobiles in the past grew rapidly and resulted with waste in billions of tones. The aim of this paper is to present an improved non-destructive disassembly process of electromechanical products using augmented reality based devices, such as glasses, tablets or mobile phones, and RFID technology for valuable product/part tracking. The proposed method includes tagging of components of interest in the product assembly by using a RFID tag. The valuable product is marked with specific ID number written in the RFID tag, in order to declare the product. The relevant data such as material and weight of components, guidelines for non-destructive disassembly for the valuable product and removing of component of interest will be obtained with the assistance of RFID tag and a centralized database. This modular system offers guidelines for the non-destructive disassembly process for obtaining valuable component of interest intended for easy repairs, remanufacture, reuse or recycling. The guidelines are in video presentation format using augmented reality for easy visualization of non-destructive disassembly process. The benefits of proposed modular system includes biggest percentage of reuse of the valuable components, easy maintaining, improved material recycling, environmental protection and greater total return form end of life products.

Design and analysis of sustainable computer mouse using design for disassembly methodology

Science.gov (United States)

Roni Sahroni, Taufik; Fitri Sukarman, Ahmad; Agung Mahardini, Karunia

2017-12-01

This paper presents the design and analysis of computer mouse using Design for Disassembly methodology. Basically, the existing computer mouse model consist a number of unnecessary part that cause the assembly and disassembly time in production. The objective of this project is to design a new computer mouse based on Design for Disassembly (DFD) methodology. The main methodology of this paper was proposed from sketch generation, concept selection, and concept scoring. Based on the design screening, design concept B was selected for further analysis. New design of computer mouse is proposed using fastening system. Furthermore, three materials of ABS, Polycarbonate, and PE high density were prepared to determine the environmental impact category. Sustainable analysis was conducted using software SolidWorks. As a result, PE High Density gives the lowers amount in the environmental category with great maximum stress value.

Disassembling and rebuilding 900 MW unit fuel assemblies in Celimene

International Nuclear Information System (INIS)

Giquel, G.; Leseur, A.; Pillet, C.; Van Craeynest, J.C.

1987-01-01

The Celimene high activity laboratory, in the Nuclear Research Centre of Saclay, has equipment for and experience of disassembling and rebuilding fuel assemblies from 900 MW light water reactors. These operations have been performed for R and D purposes; they allow removal for investigation of some of the fuel rods and examination of the skeleton. The rebuilt assemblies are sent to the fuel reprocessing plant. Reirradiation of these assemblies has not been considered so far and would require modifications of the procedure and of parts of the new skeleton. Disassembling and rebuilding have already been performed on three assemblies and a fourth one will be rebuilt in the coming months [fr

The assembly and disassembly of ecological networks.

Science.gov (United States)

Bascompte, Jordi; Stouffer, Daniel B

2009-06-27

Global change has created a severe biodiversity crisis. Species are driven extinct at an increasing rate, and this has the potential to cause further coextinction cascades. The rate and shape of these coextinction cascades depend very much on the structure of the networks of interactions across species. Understanding network structure and how it relates to network disassembly, therefore, is a priority for system-level conservation biology. This process of network collapse may indeed be related to the process of network build-up, although very little is known about both processes and even less about their relationship. Here we review recent work that provides some preliminary answers to these questions. First, we focus on network assembly by emphasizing temporal processes at the species level, as well as the structural building blocks of complex ecological networks. Second, we focus on network disassembly as a consequence of species extinctions or habitat loss. We conclude by emphasizing some general rules of thumb that can help in building a comprehensive framework to understand the responses of ecological networks to global change.

ARIES pit disassembly-safeguards issues for transparency

International Nuclear Information System (INIS)

Fearey, B.L.; Cremers, T.L.

1995-01-01

Historic changes are now occurring in U.S. nonproliferation and arms control policy. The quantity of nuclear weapons required to provide a deterrence has decreased (especially with the end of the Cold War). Further, various bilateral and multilateral treaties now require the removal of numerous nuclear weapons from the U.S. stockpile. Although the removal of such weapons appears straightforward, the final disposition of the surplus weapons-grade nuclear material must be carefully considered. Domestically, several plutonium disposition plans are now under consideration concerning long-term safety, materials accounting, environmental impact, accessibility, and long-term containment. The Automated Retirement and Integrated Extraction System (ARIES) currently under development at Los Alamos National Laboratory is one such disposition method for the disassembly of plutonium weapons components (pits). The ARIES system integrates and automates several features: disassembly of pits, consolidation of the plutonium material, on-line measurement of final products, waste streams, and long-term packaging. Clearly, in any plutonium disposition plan, the safeguards aspects of materials control and accounting and the security aspects must be carefully considered and evaluated

Spent-fuel disassembly and canning programs at the Barnwell Nuclear Fuel Plant (BNFP)

International Nuclear Information System (INIS)

Townes, G.A.

1980-02-01

Doubling pool storage and tripling truck cask shipping capability appear feasible based on preliminary development work performed at the BNFP. This would be accomplished by disassembly of the fuel assembly and canning of the fuel pins. The dry, remote disassembly and canning in the headend cells offer adequate rates, easily controlled operator exposure, and visual inspection of the fuel pins and operations through shielded windows

Balancing Disassembly Line in Product Recovery to Promote the Coordinated Development of Economy and Environment

Directory of Open Access Journals (Sweden)

Jia Liu

2017-02-01

Full Text Available For environmentally conscious and sustainable manufacturing, many more manufacturers are acting to recycle and remanufacture their post-consumed products. The most critical process of remanufacturing is disassembly, since it allows for the selective extraction of the valuable components and materials from returned products to reduce the waste disposal volume. It is, therefore, important to design and balance the disassembly line to work efficiently due to its vital role in effective resource usage and environmental protection. Considering the disassembly precedence relationships and sequence-dependent parts removal time increments, this paper presents an improved discrete artificial bee colony algorithm (DABC for solving the sequence-dependent disassembly line balancing problem (SDDLBP. The performance of the proposed algorithm was tested against nine other approaches. Computational results evidently indicate the superior efficiency of the proposed algorithm for addressing the environmental and economic concerns while optimizing the multi-objective SDDLBP.

Advanced disassembling technique of irradiated driver fuel assembly for continuous irradiation of fuel pins

International Nuclear Information System (INIS)

Ichikawa, Shoichi; Haga, Hiroyuki; Katsuyama, Kozo; Maeda, Koji; Nishinoiri, Kenji

2012-01-01

It was necessary to carry out continuous irradiation tests in order to obtain the irradiation data of high burn-up fuel and high neutron dose material for FaCT (Fast Reactor Cycle Technology Development) project. There, the disassembling technique of an irradiated fuel assembly was advanced in order to realize further continuous irradiation tests. Although the conventional disassembling technique had been cutting a lower end-plug of a fuel pin needed to fix fuel pins to an irradiation vehicle, the advanced disassembling technique did not need cutting a lower end-plug. As a result, it was possible to supply many irradiated fuel pins to various continuous irradiation tests for FaCT project. (author)

On the optimal design of the disassembly and recovery processes.

Science.gov (United States)

Xanthopoulos, A; Iakovou, E

2009-05-01

This paper tackles the problem of the optimal design of the recovery processes of the end-of-life (EOL) electric and electronic products, with a special focus on the disassembly issues. The objective is to recover as much ecological and economic value as possible, and to reduce the overall produced quantities of waste. In this context, a medium-range tactical problem is defined and a novel two-phased algorithm is presented for a remanufacturing-driven reverse supply chain. In the first phase, we propose a multicriteria/goal-programming analysis for the identification and the optimal selection of the most 'desirable' subassemblies and components to be disassembled for recovery, from a set of different types of EOL products. In the second phase, a multi-product, multi-period mixed-integer linear programming (MILP) model is presented, which addresses the optimization of the recovery processes, while taking into account explicitly the lead times of the disassembly and recovery processes. Moreover, a simulation-based solution approach is proposed for capturing the uncertainties in reverse logistics. The overall approach leads to an easy-to-use methodology that could support effectively middle level management decisions. Finally, the applicability of the developed methodology is illustrated by its application on a specific case study.

On the optimal design of the disassembly and recovery processes

International Nuclear Information System (INIS)

Xanthopoulos, A.; Iakovou, E.

2009-01-01

This paper tackles the problem of the optimal design of the recovery processes of the end-of-life (EOL) electric and electronic products, with a special focus on the disassembly issues. The objective is to recover as much ecological and economic value as possible, and to reduce the overall produced quantities of waste. In this context, a medium-range tactical problem is defined and a novel two-phased algorithm is presented for a remanufacturing-driven reverse supply chain. In the first phase, we propose a multicriteria/goal-programming analysis for the identification and the optimal selection of the most 'desirable' subassemblies and components to be disassembled for recovery, from a set of different types of EOL products. In the second phase, a multi-product, multi-period mixed-integer linear programming (MILP) model is presented, which addresses the optimization of the recovery processes, while taking into account explicitly the lead times of the disassembly and recovery processes. Moreover, a simulation-based solution approach is proposed for capturing the uncertainties in reverse logistics. The overall approach leads to an easy-to-use methodology that could support effectively middle level management decisions. Finally, the applicability of the developed methodology is illustrated by its application on a specific case study

SAVANNAH RIVER SITE R REACTOR DISASSEMBLY BASIN IN SITU DECOMMISSIONING

Energy Technology Data Exchange (ETDEWEB)

Langton, C.; Blankenship, J.; Griffin, W.; Serrato, M.

2009-12-03

The US DOE concept for facility in-situ decommissioning (ISD) is to physically stabilize and isolate in tact, structurally sound facilities that are no longer needed for their original purpose of, i.e., generating (reactor facilities), processing(isotope separation facilities) or storing radioactive materials. The 105-R Disassembly Basin is the first SRS reactor facility to undergo the in-situ decommissioning (ISD) process. This ISD process complies with the105-R Disassembly Basin project strategy as outlined in the Engineering Evaluation/Cost Analysis for the Grouting of the R-Reactor Disassembly Basin at the Savannah River Site and includes: (1) Managing residual water by solidification in-place or evaporation at another facility; (2) Filling the below grade portion of the basin with cementitious materials to physically stabilize the basin and prevent collapse of the final cap - Sludge and debris in the bottom few feet of the basin will be encapsulated between the basin floor and overlying fill material to isolate if from the environment; (3) Demolishing the above grade portion of the structure and relocating the resulting debris to another location or disposing of the debris in-place; and (4) Capping the basin area with a concrete slab which is part of an engineered cap to prevent inadvertent intrusion. The estimated total grout volume to fill the 105-R Reactor Disassembly Basin is 24,424 cubic meters or 31,945 cubic yards. Portland cement-based structural fill materials were design and tested for the reactor ISD project and a placement strategy for stabilizing the basin was developed. Based on structural engineering analyses and work flow considerations, the recommended maximum lift height is 5 feet with 24 hours between lifts. Pertinent data and information related to the SRS 105-R-Reactor Disassembly Basin in-situ decommissioning include: regulatory documentation, residual water management, area preparation activities, technology needs, fill material designs

A Taxonomy and Comparison of Haptic Actions for Disassembly Tasks

National Research Council Canada - National Science Library

Bloomfield, Aaron; Deng, Yu; Wampler, Jeff; Rondot, Pascale; Harth, Dina; McManus, Mary; Badler, Norman

2003-01-01

.... We conducted a series of human subject experiments to compare user performance and preference on a disassembly task with and without haptic feedback using CyberGlove, Phantom, and SpaceMouse interfaces...

Optimization of Two-Level Disassembly/Remanufacturing/Assembly System with an Integrated Maintenance Strategy

Directory of Open Access Journals (Sweden)

Zouhour Guiras

2018-04-01

Full Text Available With an increase of environmental pressure on economic activities, reverse flow is increasingly important. It seeks to save resources, eliminate waste, and improve productivity. This paper investigates the optimization of the disassembly, remanufacturing and assembly system, taking into account assembly-disassembly system degradation. An analytical model is developed to consider disassembly, remanufacturing of used/end-of-life product and assembly of the finished product. The finished product is composed of remanufactured and new components. A maintenance policy is sequentially integrated to reduce the system unavailability. The aim of this study is to help decision-makers, under certain conditions, choose the most cost-effective process for them to satisfy the customer as well as to adapt to the potential risk that can perturb the disassembly-assembly system. A heuristic is developed to determine the optimal ordered date of the used end-of-life product as well as the optimum release dates of new external components. The results reveal that considering some remanufacturing and purchase components costs, the proposed model is more economical in comparison with a model without remanufactured parts. Numerical results are provided to illustrate the impact of the variation of the ordering cost and quality of the used end-of-life product on the system profitability. Finally, the risk due to system repair periods is discussed, which has an impact on managerial decision-making.

What if the hand piece spring disassembles during robotic radical prostatectomy?

Science.gov (United States)

Akbulut, Ziya; Canda, Abdullah Erdem; Atmaca, Ali Fuat; Asil, Erem; Isgoren, Egemen; Balbay, Mevlana Derya

2011-01-01

Robot-assisted laparoscopic radical prostatectomy (RALRP) is successfully being performed for treating prostate cancer (PCa). However, instrumentation failure associated with robotic procedures represents a unique new problem. We report the successful completion of RALRP in spite of a disassembled hand piece spring during the procedure. A PubMed/Medline search was made concerning robotic malfunction and robot-assisted laparoscopic radical prostatectomy to discuss our experience. We performed RALRP in a 60-year-old male patient with localized PCa. During the procedure, the spring of the hand piece disassembled, and we were not able to reassemble it. We completed the procedure successfully however without fixing the disassembled hand piece spring. We were able to grasp tissue and needles when we brought our fingers together. The only movement we needed to do was to move fingers apart to release tissue or needles caught by robotic instrument. Although malfunction risk related to the da Vinci Surgical System seems to be very low, it might still occur. Sometimes, simple maneuvers may compensate for the failed function as occurred in our case. However, patients should be informed before the operation about the possibility of converting their procedure to laparoscopic or open due to robotic malfunction.

Phosphorylation of p37 is important for Golgi disassembly at mitosis

International Nuclear Information System (INIS)

Kaneko, Yayoi; Tamura, Kaori; Totsukawa, Go; Kondo, Hisao

2010-01-01

Research highlights: → p37 is phosphorylated on Serine-56 and Threonine-59 by Cdc2 at mitosis. → Phosphorylated p37 does not bind to Golgi membranes. → p37 phosphorylation inhibits p97/p37-mediated Golgi membrane fusion. -- Abstract: In mammals, the Golgi apparatus is disassembled at early mitosis and reassembled at the end of mitosis. For Golgi disassembly, membrane fusion needs to be blocked. Golgi biogenesis requires two distinct p97ATPase-mediated membrane fusion, the p97/p47 and p97/p37 pathways. We previously reported that p47 phosphorylation on Serine-140 by Cdc2 results in mitotic inhibition of the p97/p47 pathway . In this study, we demonstrate that p37 is phosphorylated on Serine-56 and Threonine-59 by Cdc2 at mitosis, and this phosphorylated p37 does not bind to Golgi membranes. Using an in vitro Golgi reassembly assay, we show that mutated p37(S56D, T59D), which mimics mitotic phosphorylation, does not cause any cisternal regrowth, indicating that p37 phosphorylation inhibits the p97/p37 pathway. Our results demonstrate that p37 phosphorylation on Serine-56 and Threonine-59 is important for Golgi disassembly at mitosis.

Disassembly and Sanitization of Classified Matter

International Nuclear Information System (INIS)

Stockham, Dwight J.; Saad, Max P.

2008-01-01

The Disassembly Sanitization Operation (DSO) process was implemented to support weapon disassembly and disposition by using recycling and waste minimization measures. This process was initiated by treaty agreements and reconfigurations within both the DOD and DOE Complexes. The DOE is faced with disassembling and disposing of a huge inventory of retired weapons, components, training equipment, spare parts, weapon maintenance equipment, and associated material. In addition, regulations have caused a dramatic increase in the need for information required to support the handling and disposition of these parts and materials. In the past, huge inventories of classified weapon components were required to have long-term storage at Sandia and at many other locations throughout the DoE Complex. These materials are placed in onsite storage unit due to classification issues and they may also contain radiological and/or hazardous components. Since no disposal options exist for this material, the only choice was long-term storage. Long-term storage is costly and somewhat problematic, requiring a secured storage area, monitoring, auditing, and presenting the potential for loss or theft of the material. Overall recycling rates for materials sent through the DSO process have enabled 70 to 80% of these components to be recycled. These components are made of high quality materials and once this material has been sanitized, the demand for the component metals for recycling efforts is very high. The DSO process for NGPF, classified components established the credibility of this technique for addressing the long-term storage requirements of the classified weapons component inventory. The success of this application has generated interest from other Sandia organizations and other locations throughout the complex. Other organizations are requesting the help of the DSO team and the DSO is responding to these requests by expanding its scope to include Work-for- Other projects. For example

AGR-2 Irradiated Test Train Preliminary Inspection and Disassembly First Look

Energy Technology Data Exchange (ETDEWEB)

Ploger, Scott [Idaho National Lab. (INL), Idaho Falls, ID (United States); Demkowciz, Paul [Idaho National Lab. (INL), Idaho Falls, ID (United States); Harp, Jason [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-05-01

The AGR 2 irradiation experiment began in June 2010 and was completed in October 2013. The test train was shipped to the Materials and Fuels Complex in July 2014 for post-irradiation examination (PIE). The first PIE activities included nondestructive examination of the test train, followed by disassembly of the test train and individual capsules and detailed inspection of the capsule contents, including the fuel compacts and their graphite fuel holders. Dimensional metrology was then performed on the compacts, graphite holders, and steel capsule shells. AGR 2 disassembly and metrology were performed with the same equipment used successfully on AGR 1 test train components. Gamma spectrometry of the intact test train gave a preliminary look at the condition of the interior components. No evidence of damage to compacts or graphite components was evident from the isotopic and gross gamma scans. Disassembly of the AGR 2 test train and its capsules was conducted rapidly and efficiently by employing techniques refined during the AGR 1 disassembly campaign. Only one major difficulty was encountered while separating the test train into capsules when thermocouples (of larger diameter than used in AGR 1) and gas lines jammed inside the through tubes of the upper capsules, which required new tooling for extraction. Disassembly of individual capsules was straightforward with only a few minor complications. On the whole, AGR 2 capsule structural components appeared less embrittled than their AGR 1 counterparts. Compacts from AGR 2 Capsules 2, 3, 5, and 6 were in very good condition upon removal. Only relatively minor damage or markings were visible using high resolution photographic inspection. Compact dimensional measurements indicated radial shrinkage between 0.8 to 1.7%, with the greatest shrinkage observed on Capsule 2 compacts that were irradiated at higher temperature. Length shrinkage ranged from 0.1 to 0.9%, with by far the lowest axial shrinkage on Capsule 3 compacts�

SAVANNAH RIVER SITE R-REACTOR DISASSEMBLY BASIN IN-SITU DECOMMISSIONING -10499

Energy Technology Data Exchange (ETDEWEB)

Langton, C.; Serrato, M.; Blankenship, J.; Griffin, W.

2010-01-04

The US DOE concept for facility in-situ decommissioning (ISD) is to physically stabilize and isolate intact, structurally sound facilities that are no longer needed for their original purpose, i.e., generating (reactor facilities), processing(isotope separation facilities) or storing radioactive materials. The 105-R Disassembly Basin is the first SRS reactor facility to undergo the in-situ decommissioning (ISD) process. This ISD process complies with the 105-R Disassembly Basin project strategy as outlined in the Engineering Evaluation/Cost Analysis for the Grouting of the R-Reactor Disassembly Basin at the Savannah River Site and includes: (1) Managing residual water by solidification in-place or evaporation at another facility; (2) Filling the below grade portion of the basin with cementitious materials to physically stabilize the basin and prevent collapse of the final cap - Sludge and debris in the bottom few feet of the basin will be encapsulated between the basin floor and overlying fill material to isolate it from the environment; (3) Demolishing the above grade portion of the structure and relocating the resulting debris to another location or disposing of the debris in-place; and (4) Capping the basin area with a concrete slab which is part of an engineered cap to prevent inadvertent intrusion. The estimated total grout volume to fill the 105-R Reactor Disassembly Basin is 24,384 cubic meters or 31,894 cubic yards. Portland cement-based structural fill materials were designed and tested for the reactor ISD project, and a placement strategy for stabilizing the basin was developed. Based on structural engineering analyses and material flow considerations, maximum lift heights and differential height requirements were determined. Pertinent data and information related to the SRS 105-R Reactor Disassembly Basin in-situ decommissioning include: regulatory documentation, residual water management, area preparation activities, technology needs, fill material

Modelling disassembled fuel bundles using CATHENA MOD-3.5a under LOCA/LOECC conditions

Energy Technology Data Exchange (ETDEWEB)

Lei, Q M; Sanderson, D B; Dutton, R [Atomic Energy of Canada Ltd., Pinawa, MB (Canada). Whiteshell Labs.

1996-12-31

CATHENA MOD-3.5a is a multipurpose thermalhydraulic computer code developed primarily to analyse postulated loss-of-coolant scenarios for CANDU nuclear reactors. The code contains a generalized heat transfer package that enables it to model the behaviour of a fuel channel in great detail. Throughout the development of the CATHENA code, considerable effort has been devoted to evaluating, validating and documenting its overall capability as a design and safety assessment tool. Specific attention has focused on its ability to predict fuel channel behaviour under postulated accident conditions. This paper describes an investigation of CATHENA`s ability to predict the thermal-chemical responses of a fuel channel in which the 37-element bundles were assumed to disassemble and rearrange into a closed-packed stack of elements at the bottom of the pressure tube. A representative disassembled bundle geometry was modelled during a simulated loss-of-coolant accident scenario using CATHENA MOD-3.5a/Rev 0, with superheated steam being the only coolant available. Thermal conduction in the radial and circumferential directions was calculated for individual fuel elements, the pressure tube, and the calandria tube. Radiation view factors for the intact and disassembled bundle geometries were calculated using a CATHENA utility program. Inter-element metal-to-metal contact was accounted for using the CATHENA solid-solid contact model. An offset pressure-tube configuration, representing a partially sagged pressure tube, and the effect of steam starvation on the exothermic zirconium-steam reaction, were included in the CATHENA model. The CATHENA-predicted results show a dramatic suppression of heat generation from the zirconium-steam reaction when bundle disassembly is initiated. The predicted results show a smaller temperature increase in the fuel sheaths and the pressure tube for the disassembled bundle geometry, compared to the temperature excursion for the intact bundle. (author

Disassembly and physical separation of electric/electronic components layered in printed circuit boards (PCB).

Science.gov (United States)

Lee, Jaeryeong; Kim, Youngjin; Lee, Jae-chun

2012-11-30

Although printed circuit boards (PCBs) contain various elements, only the major elements (i.e., those with content levels in wt% or over grade) of and precious metals (e.g., Ag, Au, and platinum groups) contained within PCBs can be recycled. To recover other elements from PCBs, the PCBs should be properly disassembled as the first step of the recycling process. The recovery of these other elements would be beneficial for efforts to conserve scarce resources, reuse electric/electronic components (EECs), and eliminate environmental problems. This paper examines the disassembly of EECs from wasted PCBs (WPCBs) and the physical separation of these EECs using a self-designed disassembling apparatus and a 3-step separation process of sieving, magnetic separation, and dense medium separation. The disassembling efficiencies were evaluated by using the ratio of grinding area (E(area)) and the weight ratio of the detached EECs (E(weight)). In the disassembly treatment, these efficiencies were improved with an increase of grinder speed and grinder height. 97.7% (E(area)) and 98% (E(weight)) could be accomplished ultimately by 3 repetitive treatments at a grinder speed of 5500 rpm and a grinder height of 1.5mm. Through a series of physical separations, most groups of the EECs (except for the diode, transistor, and IC chip groups) could be sorted at a relatively high separation efficiency of about 75% or more. To evaluate the separation efficiency with regard to the elemental composition, the distribution ratio (R(dis)) and the concentration ratio (R(conc)) were used. 15 elements could be separated with the highest R(dis) and R(conc) in the same separated division. This result implies that the recyclability of the elements is highly feasible, even though the initial content in EECs is lower than several tens of mg/kg. Copyright © 2012 Elsevier B.V. All rights reserved.

Corrosion of aluminum alloys in a reactor disassembly basin

International Nuclear Information System (INIS)

Howell, J.P.; Zapp, P.E.; Nelson, D.Z.

1992-01-01

This document discusses storage of aluminum clad fuel and target tubes of the Mark 22 assembly takes place in the concrete-lined, light-water-filled, disassembly basins located within each reactor area at the Savannah River Site (SRS). A corrosion test program has been conducted in the K-Reactor disassembly basin to assess the storage performance of the assemblies and other aluminum clad components in the current basin environment. Aluminum clad alloys cut from the ends of actual fuel and target tubes were originally placed in the disassembly water basin in December 1991. After time intervals varying from 45--182 days, the components were removed from the basin, photographed, and evaluated metallographically for corrosion performance. Results indicated that pitting of the 8001 aluminum fuel clad alloy exceeded the 30-mil (0.076 cm) cladding thickness within the 45-day exposure period. Pitting of the 1100 aluminum target clad alloy exceeded the 30-mil (0.076 cm) clad thickness in 107--182 days exposure. The existing basin water chemistry is within limits established during early site operations. Impurities such as Cl - , NO 3 - and SO 4 - are controlled to the parts per million level and basin water conductivity is currently 170--190 μmho/cm. The test program has demonstrated that the basin water is aggressive to the aluminum components at these levels. Other storage basins at SRS and around the US have successfully stored aluminum components for greater than ten years without pitting corrosion. These basins have impurity levels controlled to the parts per billion level (1000X lower) and conductivity less than 1.0 μmho/cm

Development of the spent fuel disassembling process by utilizing the 3D graphic design technology

International Nuclear Information System (INIS)

Song, T. K.; Lee, J. Y.; Kim, S. H.; Yun, J. S.

2001-01-01

For developing the spent fuel disassembling process, the 3D graphic simulation has been established by utilizing the 3D graphic design technology which is widely used in the industry. The spent fuel disassembling process consists of a downender, a rod extraction device, a rod cutting device, a pellet extracting device and a skeleton compaction device. In this study, the 3D graphical design model of these devices is implemented by conceptual design and established the virtual workcell within kinematics to motion of each device. By implementing this graphic simulation, all the unit process involved in the spent fuel disassembling processes are analyzed and optimized. The 3D graphical model and the 3D graphic simulation can be effectively used for designing the process equipment, as well as the optimized process and maintenance process

Assembly and disassembly of the nucleolus during the cell cycle.

Science.gov (United States)

Hernandez-Verdun, Danièle

2011-01-01

The nucleolus is a large nuclear domain in which transcription, maturation and assembly of ribosomes take place. In higher eukaryotes, nucleolar organization in three sub-domains reflects the compartmentation of the machineries related to active or inactive transcription of the ribosomal DNA, ribosomal RNA processing and assembly with ribosomal proteins of the two (40S and 60S) ribosomal subunits. The assembly of the nucleoli during telophase/early G(1) depends on pre-existing machineries inactivated during prophase (the transcription machinery and RNP processing complexes) and on partially processed 45S rRNAs inherited throughout mitosis. In telophase, the 45S rRNAs nucleate the prenucleolar bodies and order the dynamics of nucleolar assembly. The assembly/disassembly processes of the nucleolus depend on the equilibrium between phosphorylation/dephosphorylation of the transcription machinery and on the RNP processing complexes under the control of the CDK1-cyclin B kinase and PP1 phosphatases. The dynamics of assembly/disassembly of the nucleolus is time and space regulated.

pH-Sensitive Reversible Programmed Targeting Strategy by the Self-Assembly/Disassembly of Gold Nanoparticles.

Science.gov (United States)

Ma, Jinlong; Hu, Zhenpeng; Wang, Wei; Wang, Xinyu; Wu, Qiang; Yuan, Zhi

2017-05-24

A reversible programmed targeting strategy could achieve high tumor accumulation due to its long blood circulation time and high cellular internalization. Here, targeting ligand-modified poly(ethylene glycol) (PEG-ligand), dibutylamines (Bu), and pyrrolidinamines (Py) were introduced on the surface of gold nanoparticles (Au NPs) for reversible shielding/deshielding of the targeting ligands by pH-responsive self-assembly. Hydrophobic interaction and steric repulsion are the main driving forces for the self-assembly/disassembly of Au NPs. The precise self-assembly (pH ≥ 7.2) and disassembly (pH ≤ 6.8) of Au NPs with different ligands could be achieved by fine-tuning the modifying molar ratio of Bu and Py (R m ), which followed the formula R m = 1/(-0.0013X 2 + 0.0323X + 1), in which X is the logarithm of the partition coefficient of the targeting ligand. The assembled/disassembled behavior of Au NPs at pH 7.2 and 6.8 was confirmed by transmission electron microscopy and dynamic light scattering. Enzyme-linked immunosorbent assays and cellular uptake studies showed that the ligands could be buried inside the assembly and exposed when disassembled. More importantly, this process was reversible, which provides the possibility of prolonging blood circulation by shielding ligands associated with the NPs that were effused from tumor tissue.

Disassembling and modification of RA-3

International Nuclear Information System (INIS)

Tarizzo, R.D.

1990-01-01

The objective of this paper is to describe the partial disassembling and modification of RA-3, called the Modernization Project. It comprises all the technical and administrative steps directly related with this task. The improvement of RA-3 is a result of the lack of 90% enriched uranium obliging a change over to 20% enriched uranium. This brought about design modifications both in fuel elements and the reactor. The presentation of documents for the licensing authority as well as are detailed separately. The modernization project was divided in 25 tasks: 1) changing fuel element support table, 2) changing heat exchanger, 3) repairing of cooling towers, 4) repairing of primary circuit valves, 5) repairing of irradiation channels, 6) construction of a new sampler, 7) changing tangential channel, 8) cleaning and disassembling of reactor (inside), 9) changing continuous demineralizer (ion exchange column), 10) detection of failure in fuel elements, 11) modification of nuclear instrumentation, 12) modification of conventional instrumentation, 13) modification of electrical system, 14) changing telemanipulators, 15) construction of mechanism bridge, 16) changing a primary circuit valve when the heat exchanger is changed too, 17) painting ground floor, hall floor, and pump room floor with epoxy resin levelling, 18) installation of fire alarm system, 19) radioactive liquid discharge, 20) modification of secondary circuit (This task involves: a) installation of a third secondary pump, b) extension of this piping, c) installation of two 12 inch valves to the present cooling towers pools independent, d) installation of filtering system), 21) optimization hot water bed, 22) changing detector support table, 23) removal, decontamination and reinstallation of shielding, 25) changing pneumatic system

Phosphorylation and disassembly of intermediate filaments in mitotic cells

International Nuclear Information System (INIS)

Chou, Yinghao; Rosevear, E.; Goldman, R.D.

1989-01-01

As baby hamster kidney (BHK-21) cells enter mitosis, networks of intermediate filaments (IFs) are transformed into cytoplasmic aggregates of protofilaments. Coincident with this morphological change, the phosphate content of vimentin increases from 0.3 mol of P i per mol of protein in interphase to 1.9 mol of P i per mol of protein in mitosis. A similar increase in phosphate content is observed with desmin, from 0.5 mol of P i per mol of protein to 1.5 mol of P i per mol of protein. Fractionation of mitotic cell lysates by hydroxylapatite column chromatography reveals the presence of two IF protein kinase activities, designated as IF protein kinase I and IF protein kinase II. Comparison of two-dimensional 32 P-labeled phosphopeptide maps of vimentin and desmin phosphorylated in vivo in mitosis, and in vitro using partially purified kinase fractions, reveals extensive similarity in the two sets of phosphorylation sites. Phosphorylation of in vitro polymerized IFs by IF protein kinase II induces complete disassembly as determined by negative-stain electron microscopy. The results support the idea that the disassembly of IFs in mitosis is regulated by the phosphorylation of its subunit proteins

Design-only conceptual design report for pit disassembly and conversion facility. Rev 0

International Nuclear Information System (INIS)

Zygmunt, S.; Christensen, L.; Richardson, C.

1997-01-01

This design-only conceptual design report (DOCDR) was prepared to support a funding request by the Department of Energy (DOE)-Office of Fissile Material Disposition (OFMD) for engineering design of the Pit Disassembly and Conversion Facility (PDCF) Project No. 99-D-141. The PDCF will be used to disassemble the nation's inventory of surplus nuclear weapons pits and convert the plutonium recovered from those pits into a form suitable for storage, international inspection, and final disposition. The PDCF is a complex consisting of a hardened building that will contain the plutonium processes in a safe and secure manner, and conventional buildings and structures that will house support personnel, systems, and equipment. The PDCF uses the Advanced Recovery and Integrated Extraction System (ARIES), a low waste, modular pyroprocessing system to convert pits to plutonium oxide. The PDCF project consists of engineering and design, and construction of the buildings and structures, and engineering and design, procurement, installation, testing and start-up of equipment to disassemble pits and convert plutonium in pits to oxide form. The facility is planned to operate for 10 years, averaging 3.5 metric tons (3.86 tons) of plutonium metal per year. On conclusion of operations, the PDCF will be decontaminated and decommissioned

Design-only conceptual design report for pit disassembly and conversion facility. Rev 0

Energy Technology Data Exchange (ETDEWEB)

Zygmunt, S.; Christensen, L.; Richardson, C.

1997-12-12

This design-only conceptual design report (DOCDR) was prepared to support a funding request by the Department of Energy (DOE)-Office of Fissile Material Disposition (OFMD) for engineering design of the Pit Disassembly and Conversion Facility (PDCF) Project No. 99-D-141. The PDCF will be used to disassemble the nation`s inventory of surplus nuclear weapons pits and convert the plutonium recovered from those pits into a form suitable for storage, international inspection, and final disposition. The PDCF is a complex consisting of a hardened building that will contain the plutonium processes in a safe and secure manner, and conventional buildings and structures that will house support personnel, systems, and equipment. The PDCF uses the Advanced Recovery and Integrated Extraction System (ARIES), a low waste, modular pyroprocessing system to convert pits to plutonium oxide. The PDCF project consists of engineering and design, and construction of the buildings and structures, and engineering and design, procurement, installation, testing and start-up of equipment to disassemble pits and convert plutonium in pits to oxide form. The facility is planned to operate for 10 years, averaging 3.5 metric tons (3.86 tons) of plutonium metal per year. On conclusion of operations, the PDCF will be decontaminated and decommissioned.

Montmorillonite-induced Bacteriophage φ6 Disassembly

Science.gov (United States)

Trusiak, A.; Gottlieb, P.; Katz, A.; Alimova, A.; Steiner, J. C.; Block, K. A.

2012-12-01

It is estimated that there are 1031 virus particles on Earth making viruses an order of magnitude more prevalent in number than prokaryotes with the vast majority of viruses being bacteriophages. Clays are a major component of soils and aquatic sediments and can react with RNA, proteins and bacterial biofilms. The clays in soils serve as an important moderator between phage and their host bacteria, helping to preserve the evolutionary balance. Studies on the effects of clays on viral infectivity have given somewhat contradictory results; possibly a consequence of clay-virus interactions being dependent on the unique structure of particular viruses. In this work, the interaction between montmorillonite and the bacteriophage φ6 is investigated. φ6 is a member of the cystovirus family that infects Pseudomonas syringe, a common plant pathogen. As a member of the cystovirus family with an enveloped structure, φ6 serves as a model for reoviruses, a human pathogen. Experiments were conducted with φ6 suspended in dilute, purified homoionic commercial-grade montmorillonite over a range of virus:clay ratios. At a 1:100000 virus:clay ratio, the clay reduced viral infectivity by 99%. The minimum clay to virus ratio which results in a measurable reduction of P. syringae infection is 1:1. Electron microscopy demonstrates that mixed suspensions of smectite and virus co-aggregate to form flocs encompassing virions within the smectite. Both free viral particles as well as those imbedded in the flocs are seen in the micrographs to be missing the envelope- leaving only the nucleocapsid (NC) intact; indicating that smectite inactivates the virus by envelope disassembly. These results have strong implications in the evolution of both the φ6 virus and its P. syringae host cells. TEM of aggregate showing several disassembled NCs.

AGC-2 Disassembly Report

Energy Technology Data Exchange (ETDEWEB)

William Windes

2014-05-01

The Next Generation Nuclear Plant (NGNP) Graphite Research and Development (R&D) Program is currently measuring irradiated material properties for predicting the behavior and operating performance of new nuclear graphite grades available for use within the cores of new very high temperature reactor designs. The Advanced Graphite Creep (AGC) experiment, consisting of six irradiation capsules, will generate irradiated graphite performance data for NGNP reactor operating conditions. The AGC experiment is designed to determine the changes to specific material properties such as thermal diffusivity, thermal expansion, elastic modulus, mechanical strength, irradiation induced dimensional change rate, and irradiation creep for a wide variety of nuclear grade graphite types over a range of high temperature, and moderate doses. A series of six capsules containing graphite test specimens will be used to expose graphite test samples to a dose range from 1 to 7 dpa at three different temperatures (600, 900, and 1200°C) as described in the Graphite Technology Development Plan. Since irradiation induced creep within graphite components is considered critical to determining the operational life of the graphite core, some of the samples will also be exposed to an applied load to determine the creep rate for each graphite type under both temperature and neutron flux. All six AGC capsules in the experiment will be irradiated in the Advanced Test Reactor (ATR). AGC-1 and AGC-2 will be irradiated in the south flux trap and AGC-3–AGC-6 will be irradiated in the east flux trap. The change in flux traps is due to NGNP irradiation priorities requiring the AGC experiment to be moved to accommodate Fuel irradiation experiments. After irradiation, all six AGC capsules will be cooled in the ATR Canal, sized for shipment, and shipped to the Materials and Fuels Complex (MFC) where the capsule will be disassembled in the Hot Fuel Examination Facility (HFEF). During disassembly, the metallic

Asymmetric ring structure of Vps4 required for ESCRT-III disassembly

Science.gov (United States)

Caillat, Christophe; Macheboeuf, Pauline; Wu, Yuanfei; McCarthy, Andrew A.; Boeri-Erba, Elisabetta; Effantin, Gregory; Göttlinger, Heinrich G.; Weissenhorn, Winfried; Renesto, Patricia

2015-12-01

The vacuolar protein sorting 4 AAA-ATPase (Vps4) recycles endosomal sorting complexes required for transport (ESCRT-III) polymers from cellular membranes. Here we present a 3.6-Å X-ray structure of ring-shaped Vps4 from Metallosphera sedula (MsVps4), seen as an asymmetric pseudohexamer. Conserved key interface residues are shown to be important for MsVps4 assembly, ATPase activity in vitro, ESCRT-III disassembly in vitro and HIV-1 budding. ADP binding leads to conformational changes within the protomer, which might propagate within the ring structure. All ATP-binding sites are accessible and the pseudohexamer binds six ATP with micromolar affinity in vitro. In contrast, ADP occupies one high-affinity and five low-affinity binding sites in vitro, consistent with conformational asymmetry induced on ATP hydrolysis. The structure represents a snapshot of an assembled Vps4 conformation and provides insight into the molecular motions the ring structure undergoes in a concerted action to couple ATP hydrolysis to ESCRT-III substrate disassembly.

A Trio-Rac1-PAK1 signaling axis drives invadopodia disassembly

Science.gov (United States)

Moshfegh, Yasmin; Bravo-Cordero, Jose Javier; Miskolci, Veronika; Condeelis, John; Hodgson, Louis

2014-01-01

Rho family GTPases control cell migration and participate in the regulation of cancer metastasis. Invadopodia, associated with invasive tumor cells, are crucial for cellular invasion and metastasis. To study Rac1 GTPase in invadopodia dynamics, we developed a genetically-encoded, single-chain Rac1 Fluorescence Resonance Energy Transfer (FRET) biosensor. The biosensor shows Rac1 activity exclusion from the core of invadopodia, and higher activity when invadopodia disappear, suggesting that reduced Rac1 activity is necessary for their stability, and Rac1 activation is involved in disassembly. Photoactivating Rac1 at invadopodia confirmed this previously-unknown Rac1 function. We built an invadopodia disassembly model, where a signaling axis involving TrioGEF, Rac1, PAK1, and phosphorylation of cortactin, causing invadopodia dissolution. This mechanism is critical for the proper turnover of invasive structures during tumor cell invasion, where a balance of proteolytic activity and locomotory protrusions must be carefully coordinated to achieve a maximally invasive phenotype. PMID:24859002

Assembly, operation and disassembly manual for the Battelle Large Volume Water Sampler (BLVWS)

International Nuclear Information System (INIS)

Thomas, V.W.; Campbell, R.M.

1984-12-01

Assembly, operation and disassembly of the Battelle Large Volume Water Sampler (BLVWS) are described in detail. Step by step instructions of assembly, general operation and disassembly are provided to allow an operator completely unfamiliar with the sampler to successfully apply the BLVWS to his research sampling needs. The sampler permits concentration of both particulate and dissolved radionuclides from large volumes of ocean and fresh water. The water sample passes through a filtration section for particle removal then through sorption or ion exchange beds where species of interest are removed. The sampler components which contact the water being sampled are constructed of polyvinylchloride (PVC). The sampler has been successfully applied to many sampling needs over the past fifteen years. 9 references, 8 figures

Ufd1-Npl4 Recruit Cdc48 for Disassembly of Ubiquitylated CMG Helicase at the End of Chromosome Replication

Directory of Open Access Journals (Sweden)

Marija Maric

2017-03-01

Full Text Available Disassembly of the Cdc45-MCM-GINS (CMG DNA helicase is the key regulated step during DNA replication termination in eukaryotes, involving ubiquitylation of the Mcm7 helicase subunit, leading to a disassembly process that requires the Cdc48 “segregase”. Here, we employ a screen to identify partners of budding yeast Cdc48 that are important for disassembly of ubiquitylated CMG helicase at the end of chromosome replication. We demonstrate that the ubiquitin-binding Ufd1-Npl4 complex recruits Cdc48 to ubiquitylated CMG. Ubiquitylation of CMG in yeast cell extracts is dependent upon lysine 29 of Mcm7, which is the only detectable site of ubiquitylation both in vitro and in vivo (though in vivo other sites can be modified when K29 is mutated. Mutation of K29 abrogates in vitro recruitment of Ufd1-Npl4-Cdc48 to the CMG helicase, supporting a model whereby Ufd1-Npl4 recruits Cdc48 to ubiquitylated CMG at the end of chromosome replication, thereby driving the disassembly reaction.

Digital mock-up for the spent fuel disassembly processes

International Nuclear Information System (INIS)

Lee, J. Y.; Kim, S. H.; Song, T. G.; Kim, Y. H.; Hong, D. H.; Yoon, J. S.

2000-12-01

In this study, the graphical design system is developed and the digital mock-up is implemented for designing the spent fuel handling and disassembly processes. The system consists of a 3D graphical modeling system, a devices assembling system, and a motion simulation system. This system is used throughout the design stages from the conceptual design to the motion analysis. By using this system, all the process involved in the spent fuel handling and disassembly processes are analyzed and optimized. Also, this system is used in developing the on-line graphic simulator which synchronously simulates the motion of the equipment in a real time basis by connecting the device controllers with the graphic server through the TCP/IP network. This simulator can be effectively used for detecting the malfunctions of the process equipment which is remotely operated. Thus, the simulator enhances the reliability and safety of the spent fuel handling process by providing the remote monitoring function of the process. The graphical design system and the digital mock-up system can be effectively used for designing the process equipment, as well as the optimized process and maintenance process. And the on-line graphic simulator can be an alternative of the conventional process monitoring system which is a hardware based system

Artificial biofilms establish the role of matrix interactions in staphylococcal biofilm assembly and disassembly

Science.gov (United States)

Stewart, Elizabeth J.; Ganesan, Mahesh; Younger, John G.; Solomon, Michael J.

2015-01-01

We demonstrate that the microstructural and mechanical properties of bacterial biofilms can be created through colloidal self-assembly of cells and polymers, and thereby link the complex material properties of biofilms to well understood colloidal and polymeric behaviors. This finding is applied to soften and disassemble staphylococcal biofilms through pH changes. Bacterial biofilms are viscoelastic, structured communities of cells encapsulated in an extracellular polymeric substance (EPS) comprised of polysaccharides, proteins, and DNA. Although the identity and abundance of EPS macromolecules are known, how these matrix materials interact with themselves and bacterial cells to generate biofilm morphology and mechanics is not understood. Here, we find that the colloidal self-assembly of Staphylococcus epidermidis RP62A cells and polysaccharides into viscoelastic biofilms is driven by thermodynamic phase instability of EPS. pH conditions that induce phase instability of chitosan produce artificial S. epidermidis biofilms whose mechanics match natural S. epidermidis biofilms. Furthermore, pH-induced solubilization of the matrix triggers disassembly in both artificial and natural S. epidermidis biofilms. This pH-induced disassembly occurs in biofilms formed by five additional staphylococcal strains, including three clinical isolates. Our findings suggest that colloidal self-assembly of cells and matrix polymers produces biofilm viscoelasticity and that biofilm control strategies can exploit this mechanism. PMID:26272750

Nano-functionalized filamentous fungus hyphae with fast reversible macroscopic assembly & disassembly features.

Science.gov (United States)

Wang, Haiying; Li, Xiaorui; Chai, Liyuan; Zhang, Liyuan

2015-05-18

A uniform decoration of hyphae by polyaniline nanoparticles (PANI NPs) was achieved here. This novel hybrid structure can be effectively assembled into a film by filtration and disassembled in water by shaking. This reversible process is very fast, which promises applications in nanomaterials including adsorption.

Actin-interacting Protein 1 Promotes Disassembly of Actin-depolymerizing Factor/Cofilin-bound Actin Filaments in a pH-dependent Manner.

Science.gov (United States)

Nomura, Kazumi; Hayakawa, Kimihide; Tatsumi, Hitoshi; Ono, Shoichiro

2016-03-04

Actin-interacting protein 1 (AIP1) is a conserved WD repeat protein that promotes disassembly of actin filaments when actin-depolymerizing factor (ADF)/cofilin is present. Although AIP1 is known to be essential for a number of cellular events involving dynamic rearrangement of the actin cytoskeleton, the regulatory mechanism of the function of AIP1 is unknown. In this study, we report that two AIP1 isoforms from the nematode Caenorhabditis elegans, known as UNC-78 and AIPL-1, are pH-sensitive in enhancement of actin filament disassembly. Both AIP1 isoforms only weakly enhance disassembly of ADF/cofilin-bound actin filaments at an acidic pH but show stronger disassembly activity at neutral and basic pH values. However, a severing-defective mutant of UNC-78 shows pH-insensitive binding to ADF/cofilin-decorated actin filaments, suggesting that the process of filament severing or disassembly, but not filament binding, is pH-dependent. His-60 of AIP1 is located near the predicted binding surface for the ADF/cofilin-actin complex, and an H60K mutation of AIP1 partially impairs its pH sensitivity, suggesting that His-60 is involved in the pH sensor for AIP1. These biochemical results suggest that pH-dependent changes in AIP1 activity might be a novel regulatory mechanism of actin filament dynamics. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

Virulence factor NSs of rift valley fever virus recruits the F-box protein FBXO3 to degrade subunit p62 of general transcription factor TFIIH.

Science.gov (United States)

Kainulainen, Markus; Habjan, Matthias; Hubel, Philipp; Busch, Laura; Lau, Simone; Colinge, Jacques; Superti-Furga, Giulio; Pichlmair, Andreas; Weber, Friedemann

2014-03-01

The nonstructural protein NSs is the main virulence factor of Rift Valley fever virus (RVFV; family Bunyaviridae, genus Phlebovirus), a serious pathogen of livestock and humans in Africa. RVFV NSs blocks transcriptional upregulation of antiviral type I interferons (IFN) and destroys the general transcription factor TFIIH subunit p62 via the ubiquitin/proteasome pathway. Here, we identified a subunit of E3 ubiquitin ligases, F-box protein FBXO3, as a host cell interactor of NSs. Small interfering RNA (siRNA)-mediated depletion of FBXO3 rescued p62 protein levels in RVFV-infected cells and elevated IFN transcription by 1 order of magnitude. NSs interacts with the full-length FBXO3 protein as well as with a truncated isoform that lacks the C-terminal acidic and poly(R)-rich domains. These isoforms are present in both the nucleus and the cytoplasm. NSs exclusively removes the nuclear pool of full-length FBXO3, likely due to consumption during the degradation process. F-box proteins form the variable substrate recognition subunit of the so-called SCF ubiquitin ligases, which also contain the constant components Skp1, cullin 1 (or cullin 7), and Rbx1. siRNA knockdown of Skp1 also protected p62 from degradation, suggesting involvement in NSs action. However, knockdown of cullin 1, cullin 7, or Rbx1 could not rescue p62 degradation by NSs. Our data show that the enzymatic removal of p62 via the host cell factor FBXO3 is a major mechanism of IFN suppression by RVFV. Rift Valley fever virus is a serious emerging pathogen of animals and humans. Its main virulence factor, NSs, enables unhindered virus replication by suppressing the antiviral innate immune system. We identified the E3 ubiquitin ligase FBXO3 as a novel host cell interactor of NSs. NSs recruits FBXO3 to destroy the general host cell transcription factor TFIIH-p62, resulting in suppression of the transcriptional upregulation of innate immunity.

Early cysteine-dependent inactivation of 26S proteasomes does not involve particle disassembly

Directory of Open Access Journals (Sweden)

Martín Hugo

2018-06-01

Full Text Available Under oxidative stress 26S proteasomes suffer reversible disassembly into its 20S and 19S subunits, a process mediated by HSP70. This inhibits the degradation of polyubiquitinated proteins by the 26S proteasome and allows the degradation of oxidized proteins by a free 20S proteasome. Low fluxes of antimycin A-stimulated ROS production caused dimerization of mitochondrial peroxiredoxin 3 and cytosolic peroxiredoxin 2, but not peroxiredoxin overoxidation and overall oxidation of cellular protein thiols. This moderate redox imbalance was sufficient to inhibit the ATP stimulation of 26S proteasome activity. This process was dependent on reversible cysteine oxidation. Moreover, our results show that this early inhibition of ATP stimulation occurs previous to particle disassembly, indicating an intermediate step during the redox regulation of the 26S proteasome with special relevance under redox signaling rather than oxidative stress conditions.

VENUS-2, Reactor Kinetics with Feedback, 2-D LMFBR Disassembly Excursions

International Nuclear Information System (INIS)

Jackson, J.F.; Nicholson, R.B.; Weber, D.P.

1980-01-01

1 - Description of problem or function: VENUS-2 is an improved edition of the VENUS fast-reactor disassembly program. It is a two- dimensional (r-z) coupled neutronics-hydrodynamics code that calculates the dynamic behavior of an LMFBR during a prompt-critical disassembly excursion. It calculates the power history and fission energy release as well as the space-time histories of the fuel temperatures, core material pressures, and core material motions. Reactivity feedback effects due to Doppler broadening and reactor material motion are taken into account. 2 - Method of solution: The power and energy release are calculated using a point-kinetics formulation with up to six delayed neutron groups. The reactivity is a combination of an input driving function and feedback effects due to Doppler broadening and material motion. An adiabatic model is used to calculate the temperature increase throughout the reactor based on an initial temperature distribution and power profile provided as input data. These temperatures are, in turn, converted to fuel pressures through one of several equation of state options provided. The material motion that results from the pressure buildup is calculated by a direct finite difference solution of a set of two-dimensional (r-z) hydrodynamics equations. This is done in Lagrangian coordinates. The reactivity change associated with this motion is calculated by first-order perturbation theory. The displacements are also used to adjust the fuel densities as required for the density dependent equation-of- state option. An automatic time-step-size selection scheme is provided. 3 - Restrictions on the complexity of the problem: VENUS-2 is written so that the dimensions of the storage arrays can be readily changed to accommodate a broad range of problem sizes. In the base version, the total number of mesh intervals is restricted such that (NR+3)*(NZ+3) is less than 700, where NR and NZ are the total number of mesh intervals in the r and z

Pilot scale, alpha disassembly and decontamination facility at the Savannah River Laboratory

International Nuclear Information System (INIS)

Cadieux, J.R.; Becker, G.W. Jr.; Richardson, G.W.; Coogler, A.L.

1982-01-01

An alpha-contained pilot facility is being built at the Savannah River Laboratory (SRL) for research into the disassembly and dcontamination of noncombustible, Transuranic (TRU) waste. The design and program objectives for the facility are presented along with the initial test results from laboratory scale decontamination experiments with Pu-238 and Cm-244

Disassembled DJ-1 high molecular weight complex in cortex mitochondria from Parkinson's disease patients

Directory of Open Access Journals (Sweden)

Adler Charles

2009-07-01

Full Text Available Abstract Correction to Nural H, He P, Beach T, Sue L, Xia W, Shen Y. Disassembled DJ-1 high molecular weight complex in cortex mitochondria from Parkinson's disease patients Molecular Neurodegeneration 2009, 4:23.

Development of disassembly and pin chopping technology for FBR spent fuels

International Nuclear Information System (INIS)

Kobayashi, Tsuguyuki; Namba, Takashi; Kawabe, Yukinari; Washiya, Tadahiro

2008-01-01

Japan Atomic Power Company (JAPC) and Japan Atomic Energy Agency (JAEA) have been developing fuel disassembly and fuel pin chopping systems for a future Japanese commercial FBR. At first, the wrapper tube is cut by the slit-cut to pull it out, then the fuel pins are cut by the crop-cut at their end-plugs to separate them from the entrance nozzle. The pins are transferred to the magazine of the chopping machine. A series of tests were performed to develop this procedure. As the result of mechanical cutting tests, the CBN wheel was selected. The slit-cut tests were carried out to evaluated the cutting performance of the wheel. The wrapper tube is normally slit-cut in the circumferential direction. One CBN wheel could cut more than 5 fuel assemblies in this direction. The slit-cut in the axial direction is prepared as provision when the tube is difficult to put out. More work is needed to cut 5mm thick PNC-FMS plate in this direction without damaging the pins beneath it. As the result of the crop-cut tests of end-plugs made of ODS steel, the CBN wheel could cut the 61 pin bundle by two strokes. More work is needed to cut the 217 pin bundle. Fuel pin handling tests were performed to transfer them from the disassembly machine to the chopping machine. The Saucer tray was selected to receive the disassembled pins. All the pins were transferred and loaded into a magazine of the chopping machine. Fuel pin loading tests were conducted to optimize the magazine configuration to make the chopping length within 1.0±0.5 cm. In order to decrease the disturbance during chopping, the width of the magazine was adjusted to be 12 cm and installation of a height adjuster is favourable to control the free space above the pins. (author)

Workshop on instrumentation of the disassembled BER II

International Nuclear Information System (INIS)

Jauch, W.; Steiner, M.

1982-01-01

A workshop on the instrumentation of a disassembled BER II-reactor took place in the Hahn-Meitner-Institute in Berlin on April 19 and 20, 1982. Invited were all groups that are promoted by the associations 'Neutron Scattering for Investigation of Condensed Substance' and 'Neutron Scattering and Complementary Methods in Chemistry and Biology', along with experts for neutron spectrometers. 40 foreign scientists from 22 different institutes had accepted the invitation. The actual questions were treated in 13 presentations and a certain number of posters, with the latter also comprising activation analysis. The present report contains the presentations submitted, the final discussion minutes and a summary from HMI-view. (orig./RW) [de

The Effect of Uncertain End-of-Life Product Quality and Consumer Incentives on Partial Disassembly Sequencing in Value Recovery Operations

OpenAIRE

Rickli, Jeremy Lewis

2013-01-01

This dissertation addresses gaps in the interaction between End-of-Life (EoL) product acquisition systems and disassembly sequencing. The research focuses on two remanufacturing research problems; 1) modeling uncertain EoL product quality, quantity, and timing in regards to EoL product acquisition and disassembly sequencing and 2) designing EoL product acquisition schemes considering EoL product uncertainty. The main research objectives within these areas are; analyzing, predicting, and contr...

A reactor vessel and its internals disassembled and packaged

International Nuclear Information System (INIS)

Eisenmann, B.; Prechtl, E.; Suessdorf, W.

2008-01-01

2007 was a successful year for the Disassembly Unit of the Karlsruhe Research Center: dismantling the highly activated Karlsruhe Multipurpose Research Reactor (MZFR) was completed successfully and without any incident. A vote of thanks is expressed at this point to all staff members, participating industries and institutions for their extraordinary commitment and their outstanding innovation and work. Preserving and advancing existing knowledge is one of the important pillars securing a sustainable future for generations to come in Germany. Securing and advancing know-how in nuclear technology was defined as a major duty last in late January 2008 by Dr. Peter Fritz, Chairman of the Kerntechnische Gesellschaft e.V. (KTG) and member of the Executive Board of the Karlsruhe Research Center, for instance, in cooperation between the KERNTECHNIK (i.e. nuclear technology) Southwestern Research and Teaching Association and the Karlsruhe Institute of Technology (KIT). The borders of Germany do not constitute a natural radiological barrier, despite the efforts by political groups in this country to convey this impression. This report therefore is to document that the demolition of a nuclear reactor with a high radioactivity inventory can be managed safely. In the light of the experience accumulated with the MZFR, this is feasible only if demolition is carried out immediately instead of the 'problem' of disassembly and conditioning being shifted to future generations. The article is also meant to be a piece of advice by showing the unplannable difficulties which came up, and the technical solutions implemented by the competence team successfully and efficiently. (orig.)

Prey and mound disassembly, manipulation and transport by fire ant collectives

Science.gov (United States)

Dutta, Bahnisikha; Monaenkova, Daria; Goodisman, Michael A.; Goldman, Daniel

Fire ants inhabit subterranean nests covered by a hemispherical mound of soil permeated by narrow ( 1 body length diameter) tunnels. Fire ants can use their mound for long-term food storage [Gayahan &Tschinkel, J. Insect Sci.,2008]. Since mound tunnels are narrow, we expect that in addition to prey manipulation, mound reconfiguration could also be an important aspect of the food storage strategy. Ant colonies collected from wild were allowed to build nests in containers filled with clay soil in the laboratory. These colonies were offered diverse prey embedded with lead markers, including mealworms, crickets and shrimp. Ant-prey-soil interactions on the nest surface were recorded using overhead video and subsurface using x-ray imaging. Individual ants involved in prey storage exhibited three distinct behaviors: prey maneuvering, prey dissection and mound reconfiguration. Small prey (e.g. mealworms) were collectively carried intact into the mound through a tunnel, and then disassembled within the mound. Larger prey (e.g. shrimp) were dismantled into small pieces above the surface and carried to mound tunnels. The bodies of hard medium-sized prey (e.g. crickets) were buried after limb removal and then disassembled and moved into tunnels. Soil reconfiguration occurred in all cases.

Cofilin phosphorylation is elevated after F-actin disassembly induced by Rac1 depletion.

Science.gov (United States)

Liu, Linna; Li, Jing; Zhang, Liwang; Zhang, Feng; Zhang, Rong; Chen, Xiang; Brakebusch, Cord; Wang, Zhipeng; Liu, Xinyou

2015-01-01

Cytoskeletal reorganization is essential to keratinocyte function. Rac1 regulates cytoskeletal reorganization through signaling pathways such as the cofilin cascade. Cofilin severs actin filaments after activation by dephosphorylation. Rac1 was knocked out in mouse keratinocytes and it was found that actin filaments disassembled. In the epidermis of mice in which Rac1 was knocked out only in keratinocytes, cofilin phosphorylation was aberrantly elevated, corresponding to repression of the phosphatase slingshot1 (SSH1). These effects were independent of the signaling pathways for p21-activated kinase/LIM kinase (Pak/LIMK), protein kinase C, or protein kinase D or generation of reactive oxygen species. Similarly, when actin polymerization was specifically inhibited or Rac1 was knocked down, cofilin phosphorylation was enhanced and SSH1 was repressed. Repression of SSH1 partially blocked actin depolymerization induced by Rac1 depletion. Therefore, aberrant cofilin phosphorylation that induces actin polymerization might be a consequence of actin disassembly induced by the absence of Rac1. © 2015 International Union of Biochemistry and Molecular Biology.

Engineering multifunctional protein nanoparticles by in vitro disassembling and reassembling of heterologous building blocks

Science.gov (United States)

Unzueta, Ugutz; Serna, Naroa; Sánchez-García, Laura; Roldán, Mónica; Sánchez-Chardi, Alejandro; Mangues, Ramón; Villaverde, Antonio; Vázquez, Esther

2017-12-01

The engineering of protein self-assembling at the nanoscale allows the generation of functional and biocompatible materials, which can be produced by easy biological fabrication. The combination of cationic and histidine-rich stretches in fusion proteins promotes oligomerization as stable protein-only regular nanoparticles that are composed by a moderate number of building blocks. Among other applications, these materials are highly appealing as tools in targeted drug delivery once empowered with peptidic ligands of cell surface receptors. In this context, we have dissected here this simple technological platform regarding the controlled disassembling and reassembling of the composing building blocks. By applying high salt and imidazole in combination, nanoparticles are disassembled in a process that is fully reversible upon removal of the disrupting agents. By taking this approach, we accomplish here the in vitro generation of hybrid nanoparticles formed by heterologous building blocks. This fact demonstrates the capability to generate multifunctional and/or multiparatopic or multispecific materials usable in nanomedical applications.

Spent fuel disassembly hardware and other non-fuel bearing components: characterization, disposal cost estimates, and proposed repository acceptance requirements

Energy Technology Data Exchange (ETDEWEB)

Luksic, A.T.; McKee, R.W.; Daling, P.M.; Konzek, G.J.; Ludwick, J.D.; Purcell, W.L.

1986-10-01

There are two categories of waste considered in this report. The first is the spent fuel disassembly (SFD) hardware. This consists of the hardware remaining after the fuel pins have been removed from the fuel assembly. This includes end fittings, spacer grids, water rods (BWR) or guide tubes (PWR) as appropriate, and assorted springs, fasteners, etc. The second category is other non-fuel-bearing (NFB) components the DOE has agreed to accept for disposal, such as control rods, fuel channels, etc., under Appendix E of the standard utiltiy contract (10 CFR 961). It is estimated that there will be approximately 150 kg of SFD and NFB waste per average metric ton of uranium (MTU) of spent uranium. PWR fuel accounts for approximately two-thirds of the average spent-fuel mass but only 50 kg of the SFD and NFB waste, with most of that being spent fuel disassembly hardware. BWR fuel accounts for one-third of the average spent-fuel mass and the remaining 100 kg of the waste. The relatively large contribution of waste hardware in BWR fuel, will be non-fuel-bearing components, primarily consisting of the fuel channels. Chapters are devoted to a description of spent fuel disassembly hardware and non-fuel assembly components, characterization of activated components, disposal considerations (regulatory requirements, economic analysis, and projected annual waste quantities), and proposed acceptance requirements for spent fuel disassembly hardware and other non-fuel assembly components at a geologic repository. The economic analysis indicates that there is a large incentive for volume reduction.

Sequential phosphorylation of GRASP65 during mitotic Golgi disassembly

Directory of Open Access Journals (Sweden)

Danming Tang

2012-09-01

GRASP65 phosphorylation during mitosis and dephosphorylation after mitosis are required for Golgi disassembly and reassembly during the cell cycle. At least eight phosphorylation sites on GRASP65 have been identified, but whether they are modified in a coordinated fashion during mitosis is so far unknown. In this study, we raised phospho-specific antibodies that recognize phosphorylated T220/T224, S277 and S376 residues of GRASP65, respectively. Biochemical analysis showed that cdc2 phosphorylates all three sites, while plk1 enhances the phosphorylation. Microscopic studies using these antibodies for double and triple labeling demonstrate sequential phosphorylation and dephosphorylation during the cell cycle. S277 and S376 are phosphorylated from late G2 phase through metaphase until telophase when the new Golgi is reassembled. T220/224 is not modified until prophase, but is highly modified from prometaphase to anaphase. In metaphase, phospho-T220/224 signal localizes on both Golgi haze and mitotic Golgi clusters that represent dispersed Golgi vesicles and Golgi remnants, respectively, while phospho-S277 and S376 labeling is more concentrated on mitotic Golgi clusters. Expression of a phosphorylation-resistant GRASP65 mutant T220A/T224A inhibited mitotic Golgi fragmentation to a much larger extent than the expression of the S277A and S376A mutants. In cytokinesis, T220/224 dephosphorylation occurs prior to that of S277, but after S376. This study provides evidence that GRASP65 is sequentially phosphorylated and dephosphorylated during mitosis at different sites to orchestrate Golgi disassembly and reassembly during cell division, with phosphorylation of the T220/224 site being most critical in the process.

Engineering scale tests of mechanical disassembly and short stroke shearing systems for FBR fuel assembly

International Nuclear Information System (INIS)

Higuchi, Hidetoshi; Kitagaki, Toru; Koizumi, Kenji; Hirano, Hiroyasu; Takeuchi, Masayuki; Washiya, Tadahiro; Kawabe, Yukinari; Kobayashi, Tsuguyuki

2011-01-01

Japan Atomic Energy Agency (JAEA) and The Japan Atomic Power Company (JAPC) have been developing an advanced head-end process based on mechanical disassembly and short stroke shearing systems as a part of Fast Reactor Cycle Technology Development (FaCT). Fuel pins for a fast reactor are installed within a hexagonal shaped wrapper tube made of stainless steel. In order to reprocess the fast reactor fuel pins, they must be removed from the wrapper tube and transported to the shearing system without failure. In addition, the advanced aqueous reprocessing process, called 'NEXT' (New Extraction System for TRU Recovery) process requires a solution of the spent fuel with relatively high concentration (500g/L). JAEA and JAPC have developed the mechanical disassembly and the short stroke shearing technology which is expected to make fragmented fuel to satisfy these requirements. This paper reports the results of engineering scale tests on the mechanical disassembly and short stroke shearing systems. These tests were carried out with simulated FBR fuel assembly and removed pins. The mechanical cutting method has been developed to avoid fuel pin failure during disassembly operation. The cutting process is divided into two modes, so called 'slit-cut' for cutting the wrapper tube and 'crop-cut' for the end plug region of the fuel pin bundle. In the slit-cut mode, the depth of cutting was automatically controlled based on the calculated wastage of the cutting tool and deformation of the wrapper tube which had been measured before the cutting. This procedure was confirmed to minimize the fuel pin failure which was hard to prevent in the case of laser cutting. The cutting speed was also controlled automatically by the electric current of the cutting motor to lower the load of the cutting tool. The removed fuel pins were transported to the shearing machine, whose fuel shearing magazine width was set to be narrow to realize the suitable configuration for the short stroke shearing

[Study on the liver-protective and choleretic effect of zhizi baipi soup and its disassembled prescription].

Science.gov (United States)

Xiao, Xu; Zhu, Ji-Xiao; Luo, Guang-Ming; Li, Lei; Zhu, Yu-Ye; Zeng, Jin-Xiang; Wang, Xiao-Yun; Wu, Bo

2013-07-01

To investigate the effect of Zhizi Baipi soup and its disassembled prescription on protecting liver and improving choleresis and explore the regularity of Zhizi Baipi soup composition. The model of mouse liver injury induced by carbon tetraehlofide (CCl4) was used to observe the effects of Zhizi Baipi soup and its disassembled prescription by oral adminstration, the bile volume was determinied by common bile duct drainage. Zhizi Baipi soup and each treatment group with gardenia could significantly inhibit the increased serum ATL and AST activities, reduce liver MDA level, and significantly promote the bile flow and bilirubin in bile in normal rats. Zhizi Baipi soup has effects on protecting liver and increasing bile secretion, its monarch drug, gardenia plays an important role in the decoction, the effect of eliminating dampness and heat are mainly ascribed to the synergic effect of gardenia and phellodendron.

Remote disassembly of radioactively contaminated vessels by means of an arc saw

International Nuclear Information System (INIS)

Beitel, G.A.

1977-01-01

The arc saw, a newly developed tool, is a toothless circular saw which cuts by means of an electric arc. Cutting speeds between 20 to 30 cm 2 /S and depths up to 45 cm are possible. There is no mechanical contact between blade and work piece, no binding, and no blade breakage. The arc saw will be applied to the rapid and remote disassembly of multiple ton, contaminated stainless steel vessels

Conceptual design report for the mechanical disassembly of Fort St. Vrain fuel elements

International Nuclear Information System (INIS)

Lord, D.L.; Wadsworth, D.C.; Sekot, J.P.; Skinner, K.L.

1993-04-01

A conceptual design study was prepared that: (1) reviewed the operations necessary to perform the mechanical disassembly of Fort St. Vrain fuel elements; (2) contained a description and survey of equipment capable of performing the necessary functions; and (3) performed a tradeoff study for determining the preferred concepts and equipment specifications. A preferred system was recommended and engineering specifications for this system were developed

Conceptual design report for the mechanical disassembly of Fort St. Vrain fuel elements

Energy Technology Data Exchange (ETDEWEB)

Lord, D.L. [Westinghouse Idaho Nuclear Co., Inc., Idaho Falls, ID (United States); Wadsworth, D.C.; Sekot, J.P.; Skinner, K.L. [EG and G Idaho, Inc., Idaho Falls, ID (United States)

1993-04-01

A conceptual design study was prepared that: (1) reviewed the operations necessary to perform the mechanical disassembly of Fort St. Vrain fuel elements; (2) contained a description and survey of equipment capable of performing the necessary functions; and (3) performed a tradeoff study for determining the preferred concepts and equipment specifications. A preferred system was recommended and engineering specifications for this system were developed.

[PHAHs levels in soil samples from the E-waste disassembly sites and their sources allocation].

Science.gov (United States)

Zhao, Gao-Feng; Wang, Zi-Jian

2009-06-15

Soil samples (each with 3 replicates of - 1 kg, at the top 0-5 cm layer) were collected from each of the e-waste disassembly sites and the control site. Also obtained from each disassembly site were samples (each weighing - 0.2 kg) of cable coating,stuffing powder, and circuit boards chipping. The contents of 23 PBB congeners, 12 PBDE congeners, and 27 PCB congeners in soil and in their potential sources, including e-waste residues, were measured using the GC-MS5975B technique. The highest level of PBBs was found in the cable coating among the three e-waste residues, with a concentration of 35.25 ng x g(-1). The contents of low-brominated PBBs (including monobromobiphenyls and dibromobiphenyls) accounted for 38% of the total PBBs concentration observed in cable coating sample. The highest levels of PBDEs and PBDE209 were found in the stuffing powder for electronic component among the collected e-waste residues, with a concentration of 29.71 and 4.19 x 10(3) ng x g(-1). PBDE153 and PBDE183 were the most predominant PBDE congeners, with their concentration accounting for 43% and 24% of the total PBDEs concentration observed in the stuffing powder sample, respectively. Levels of PCBs in cable coating were the highest in these e-waste residues, with a concentration of 680.02 ngx g(-1). The observed values of the three PHAHs in soils from the disassembly site were considerably higher than their corresponding values observed in the control site (p < 0.05), which indicates that these PHAHs from e-waste is the pollution source of local environment.

Connexin43 hemichannels contributes to the disassembly of cell junctions through modulation of intracellular oxidative status

Directory of Open Access Journals (Sweden)

Yuan Chi

2016-10-01

Full Text Available Connexin (Cx hemichannels regulate many cellular processes with little information available regarding their mechanisms. Given that many pathological factors that activate hemichannels also disrupts the integrity of cellular junctions, we speculated a potential participation of hemichannels in the regulation of cell junctions. Here we tested this hypothesis. Exposure of renal tubular epithelial cells to Ca2+-free medium led to disassembly of tight and adherens junctions, as indicated by the reduced level of ZO-1 and cadherin, disorganization of F-actin, and severe drop in transepithelial electric resistance. These changes were preceded by an activation of Cx43 hemichannels, as revealed by extracellular efflux of ATP and intracellular influx of Lucifer Yellow. Inhibition of hemichannels with chemical inhibitors or Cx43 siRNA greatly attenuated the disassembly of cell junctions. Further analysis using fetal fibroblasts derived from Cx43 wide-type (Cx43+/+, heterozygous (Cx43+/- and knockout (Cx43-/- littermates showed that Cx43-positive cells (Cx43+/+ exhibited more dramatic changes in cell shape, F-actin, and cadherin in response to Ca2+ depletion, as compared to Cx43-null cells (Cx43-/-. Consistently, these cells had higher level of protein carbonyl modification and phosphorylation, and much stronger activation of P38 and JNK. Hemichannel opening led to extracellular loss of the major antioxidant glutathione (GSH. Supplement of cells with exogenous GSH or inhibition of oxidative sensitive kinases largely prevented the above-mentioned changes. Taken together, our study indicates that Cx43 hemichannels promote the disassembly of cell junctions through regulation of intracellular oxidative status.

Evidence of the Disassembly of α-Cyclodextrin-octylamine Inclusion Compounds Conjugated to Gold Nanoparticles via Thermal and Photothermal Effects

Directory of Open Access Journals (Sweden)

Nataly Silva

2016-10-01

Full Text Available Cyclodextrin (CD molecules form inclusion compounds (ICs, generating dimers that are capable of encapsulating molecules derived from long-chain hydrocarbons. The aim of this study is to evaluate the structural changes experienced by ICs in solution with increasing temperatures. For this, a nuclear magnetic resonance (1H-NMR titration was performed to determinate the stoichiometric α-cyclodextrin (α-CD:octylamine (OA 2:1 and binding constant (k = 2.16 M−2 of ICs. Solution samples of α-CD-OA ICs conjugated with gold nanoparticles (AuNPs were prepared, and 1H-NMR spectra at different temperatures were recorded. Comparatively, 1H-NMR spectra of the sample irradiated with a laser with tunable wavelengths, with plasmons of conjugated AuNPs, were recorded. In this work, we present evidence of the disassembly of ICs conjugated with AuNPs. Thermal studies demonstrated that, at 114 °C, there are reversible rearrangements of the host and guests in the ICs in a solid state. Migration movements of the guest molecules from the CD cavity were monitored via temperature-dependent 1H-NMR, and were verified comparing the chemical shifts of octylamine dissolved in deuterated dimethylsulfoxide (DMSO-d6 with the OA molecule included in α-CD dissolved in the same solvent. It was observed that, at 117 °C, OA exited the α-CD cavity. CD IC dimer disassembly was also observed when the sample was irradiated with green laser light.

Knowledge of damage identification about tensegrities via flexibility disassembly

Science.gov (United States)

Jiang, Ge; Feng, Xiaodong; Du, Shigui

2017-12-01

Tensegrity structures composing of continuous cables and discrete struts are under tension and compression, respectively. In order to determine the damage extents of tensegrity structures, a new method for tensegrity structural damage identification is presented based on flexibility disassembly. To decompose a tensegrity structural flexibility matrix into the matrix represention of the connectivity between degress-of-freedoms and the diagonal matrix comprising of magnitude informations. Step 1: Calculate perturbation flexibility; Step 2: Compute the flexibility connectivity matrix and perturbation flexibility parameters; Step 3: Calculate the perturbation stiffness parameters. The efficiency of the proposed method is demonstrated by a numeical example comprising of 12 cables and 4 struts with pretensioned. Accurate identification of local damage depends on the availability of good measured data, an accurate and reasonable algorithm.

MgATP hydrolysis destabilizes the interaction between subunit H and yeast V1-ATPase, highlighting H's role in V-ATPase regulation by reversible disassembly.

Science.gov (United States)

Sharma, Stuti; Oot, Rebecca A; Wilkens, Stephan

2018-05-12

Vacuolar H+-ATPases (V-ATPases; V1Vo-ATPases) are rotary motor proton pumps that acidify intracellular compartments and in some tissues, the extracellular space. V-ATPase is regulated by reversible disassembly into autoinhibited V1-ATPase and Vo proton channel sectors. An important player in V-ATPase regulation is subunit H, which binds at the interface of V1 and Vo. H is required for MgATPase activity in holo V-ATPase, but also for stabilizing the MgADP inhibited state in membrane detached V1. However, how H fulfills these two functions is poorly understood. To characterize the H-V1 interaction and its role in reversible disassembly, we determined binding affinities of full length H and its N-terminal domain (HNT) for an isolated heterodimer of subunits E and G (EG), the N-terminal domain of subunit a (aNT), and V1 lacking subunit H (V1ΔH). Using isothermal titration calorimetry (ITC) and biolayer interferometry (BLI), we show that HNT binds EG with moderate affinity, that full length H binds aNT weakly, and that both H and HNT bind V1ΔH with high affinity. We also found that only one molecule of HNT binds V1ΔH with high affinity, suggesting conformational asymmetry of the three EG heterodimers in V1ΔH. Moreover, MgATP hydrolysis-driven conformational changes in V1 destabilized the interaction of H, or HNT, with V1ΔH, suggesting an interplay between MgADP inhibition and subunit H. Our observation that H binding is affected by MgATP hydrolysis in V1 points to H's role in the mechanism of reversible disassembly. Published under license by The American Society for Biochemistry and Molecular Biology, Inc.

Interactive domains in the molecular chaperone human alphaB crystallin modulate microtubule assembly and disassembly.

Directory of Open Access Journals (Sweden)

Joy G Ghosh

2007-06-01

Full Text Available Small heat shock proteins regulate microtubule assembly during cell proliferation and in response to stress through interactions that are poorly understood.Novel functions for five interactive sequences in the small heat shock protein and molecular chaperone, human alphaB crystallin, were investigated in the assembly/disassembly of microtubules and aggregation of tubulin using synthetic peptides and mutants of human alphaB crystallin.The interactive sequence (113FISREFHR(120 exposed on the surface of alphaB crystallin decreased microtubule assembly by approximately 45%. In contrast, the interactive sequences, (131LTITSSLSSDGV(142 and (156ERTIPITRE(164, corresponding to the beta8 strand and the C-terminal extension respectively, which are involved in complex formation, increased microtubule assembly by approximately 34-45%. The alphaB crystallin peptides, (113FISREFHR(120 and (156ERTIPITRE(164, inhibited microtubule disassembly by approximately 26-36%, and the peptides (113FISREFHR(120 and (131LTITSSLSSDGV(142 decreased the thermal aggregation of tubulin by approximately 42-44%. The (131LTITSSLSSDGV(142 and (156ERTIPITRE(164 peptides were more effective than the widely used anti-cancer drug, Paclitaxel, in modulating tubulinmicrotubule dynamics. Mutagenesis of these interactive sequences in wt human alphaB crystallin confirmed the effects of the alphaB crystallin peptides on microtubule assembly/disassembly and tubulin aggregation. The regulation of microtubule assembly by alphaB crystallin varied over a narrow range of concentrations. The assembly of microtubules was maximal at alphaB crystallin to tubulin molar ratios between 1:4 and 2:1, while molar ratios >2:1 inhibited microtubule assembly.Interactive sequences on the surface of human alphaB crystallin collectively modulate microtubule assembly through a dynamic subunit exchange mechanism that depends on the concentration and ratio of alphaB crystallin to tubulin. These are the first

Polygons and adhesion plaques and the disassembly and assembly of myofibrils in cardiac myocytes.

Science.gov (United States)

Lin, Z X; Holtzer, S; Schultheiss, T; Murray, J; Masaki, T; Fischman, D A; Holtzer, H

1989-06-01

Successive stages in the disassembly of myofibrils and the subsequent assembly of new myofibrils have been studied in cultures of dissociated chick cardiac myocytes. The myofibrils in trypsinized and dispersed myocytes are sequentially disassembled during the first 3 d of culture. They split longitudinally and then assemble into transitory polygons. Multiples of single sarcomeres, the cardiac polygons, are analogous to the transitory polygonal configurations assumed by stress fibers in spreading fibroblasts. They differ from their counterparts in fibroblasts in that they consist of muscle alpha-actinin vertices and muscle myosin heavy chain struts, rather than of the nonmuscle contractile protein isoforms of stress fiber polygons. EM sections reveal the vertices and struts in cardiac polygons to be typical Z and A bands. Most cardiac polygons are eliminated by day 5 of culture. Concurrent with the disassembly and elimination of the original myofibrils new myofibrils are rapidly assembled elsewhere in the same myocyte. Without exception both distal tips of each nascent myofibril terminate in adhesion plaques. The morphology and composition of the adhesion plaques capping each end of each myofibril are similar to those of the termini of stress fibers in fibroblasts. However, whereas the adhesion complexes involving stress fibers in fibroblasts consist of vinculin/nonmuscle alpha-actinin/beta- and gamma-actins, the analogous structures in myocytes involving myofibrils consist of vinculin/muscle alpha-actinin/alpha-actin. The addition of 1.7-2.0 microns sarcomeres to the distal tips of an elongating myofibril, irrespective of whether the myofibril consists of 1, 10, or several hundred tandem sarcomeres, occurs while the myofibril appears to remain linked to its respective adhesion plaques. The adhesion plaques in vitro are the equivalent of the in vivo intercalated discs, both in terms of their molecular composition and with respect to their functioning as initiating

Decommissioning of nuclear facilities: Decontamination, disassembly and waste management

International Nuclear Information System (INIS)

1983-01-01

The term 'decommissioning', as used within the nuclear industry, means the actions taken at the end of a facility's useful life to retire the facility from service in a manner that provides adequate protection for the health and safety of the decommissioning workers, the general public, and for the environment. These actions can range from merely closing down the facility and a minimal removal of radioactive material coupled with continuing maintenance and surveillance, to a complete removal of residual radioactivity in excess of levels acceptable for unrestricted use of the facility and its site. This latter condition, unrestricted use, is the ultimate goal of all decommissioning actions at retired nuclear facilities. The purpose of this report is to provide an information base on the considerations important to decommissioning, the methods available for decontamination and disassembly of a nuclear facility, the management of the resulting radioactive wastes, and the areas of decommissioning methodology where improvements might be made. Specific sections are devoted to each of these topics, and conclusions are presented concerning the present status of each topic. A summary of past decommissioning experience in Member States is presented in the Appendix. The report, with its discussions of necessary considerations, available operational methods, and waste management practices, together with supporting references, provides an appreciation of the activities that comprise decommissioning of nuclear facilities. It is anticipated that the information presented in the report should prove useful to persons concerned with the development of plans for the decommissioning of retired nuclear facilities

Characterization of the disassembly and reassembly of the HBV glycoprotein surface antigen, a pliable nanoparticle vaccine platform

International Nuclear Information System (INIS)

Gallagher, John R.; Torian, Udana; McCraw, Dustin M.; Harris, Audray K.

2017-01-01

While nanoparticle vaccine technology is gaining interest due to the success of vaccines like those for the human papillomavirus that is based on viral capsid nanoparticles, little information is available on the disassembly and reassembly of viral surface glycoprotein-based nanoparticles. One such particle is the hepatitis B virus surface antigen (sAg) that exists as nanoparticles. Here we show, using biochemical analysis coupled with electron microscopy, that sAg nanoparticle disassembly requires both reducing agent to disrupt intermolecular disulfide bonds, and detergent to disrupt hydrophobic interactions that stabilize the nanoparticle. Particles were otherwise resistant to salt and urea, suggesting the driving mechanism of particle formation involves hydrophobic interactions. We reassembled isolated sAg protein into nanoparticles by detergent removal and reassembly resulted in a wider distribution of particle diameters. Knowledge of these driving forces of nanoparticle assembly and stability should facilitate construction of epitope-displaying nanoparticles that can be used as immunogens in vaccines.

Characterization of the disassembly and reassembly of the HBV glycoprotein surface antigen, a pliable nanoparticle vaccine platform

Energy Technology Data Exchange (ETDEWEB)

Gallagher, John R.; Torian, Udana; McCraw, Dustin M.; Harris, Audray K., E-mail: harrisau@mail.nih.gov

2017-02-15

While nanoparticle vaccine technology is gaining interest due to the success of vaccines like those for the human papillomavirus that is based on viral capsid nanoparticles, little information is available on the disassembly and reassembly of viral surface glycoprotein-based nanoparticles. One such particle is the hepatitis B virus surface antigen (sAg) that exists as nanoparticles. Here we show, using biochemical analysis coupled with electron microscopy, that sAg nanoparticle disassembly requires both reducing agent to disrupt intermolecular disulfide bonds, and detergent to disrupt hydrophobic interactions that stabilize the nanoparticle. Particles were otherwise resistant to salt and urea, suggesting the driving mechanism of particle formation involves hydrophobic interactions. We reassembled isolated sAg protein into nanoparticles by detergent removal and reassembly resulted in a wider distribution of particle diameters. Knowledge of these driving forces of nanoparticle assembly and stability should facilitate construction of epitope-displaying nanoparticles that can be used as immunogens in vaccines.

Underwater Nuclear Fuel Disassembly and Rod Storage Process and Equipment Description. Volume II

International Nuclear Information System (INIS)

Viebrock, J.M.

1981-09-01

The process, equipment, and the demonstration of the Underwater Nuclear Fuel Disassembly and Rod Storage System are presented. The process was shown to be a viable means of increasing spent fuel pool storage density by taking apart fuel assemblies and storing the fuel rods in a denser fashion than in the original storage racks. The assembly's nonfuel-bearing waste is compacted and containerized. The report documents design criteria and analysis, fabrication, demonstration program results, and proposed enhancements to the system

Assessment of the impacts of spent fuel disassembly alternatives on the Nuclear Waste Isolation System

International Nuclear Information System (INIS)

1984-07-01

The objective of this report was to evaluate four possible alternative methods of preparing and packaging spent fuel assemblies for geologic disposal against the Reference Process of unmodified spent fuel. The four alternative processes were: (1) End fitting removal, (2) Fission gas venting and resealing, (3) Fuel bundle disassembly and close packing of fuel pins, and (4) Fuel shearing and immobilization. Systems analysis was used to develop a basis of comparison of the alternatives. Conceptual processes and facility layouts were devised for each of the alternatives, based on technology deemed feasible for the purpose. Assessments were made of 15 principal attributes from the technical, operational, safety/risk, and economic considerations related to each of the alternatives, including both the surface packaging and underground repository operations. Specific attributes of the alternative processes were evaluated by assigning a number for each that expressed its merit relative to the corresponding attribute of the Reference Process. Each alternative process was then ranked by summing the numbers for attributes in each of the four assessment areas and collectively. Fuel bundle disassembly and close packing of fuel pins was ranked the preferred method of disposal of spent fuel. 63 references, 46 figures, 46 tables

Innovation and employee injury risk in automotive disassembly operations

DEFF Research Database (Denmark)

Neumann, W. Patrick; Winkel, Jørgen; Palmerud, Gunnar

2018-01-01

to control injury hazards as part of the development and design process. These cases suggest how failure to manage RSI hazards in the innovation process may allow increases of injury risks that can compromise operational performance. This ‘innovation pitfall’ has implications for operator health...... increased movement speeds and reduced muscular recovery opportunities, implying increased RSI risk. This case study reveals a mechanism by which innovation may increase RSI risks for operators. Managers responsible for engineering innovation should ensure their teams have the tools and mandate necessary......Engineering innovations in car disassembly systems are studied for affects on system operators’ risk of repetitive strain injury (RSI). Objective instrumented measures of injury risk factors with synchronised video-based task analyses were used to examine changes in operators’ RSI risk during...

Disassembly Control of Saccharide-Based Amphiphiles Driven by Electrostatic Repulsion.

Science.gov (United States)

Yamada, Taihei; Kokado, Kenta; Sada, Kazuki

2017-03-14

According to the design of disassembly using electrostatic repulsion, novel amphiphiles consisting of a lipophilic ion part and a hydrophilic saccharide part were synthesized via the facile copper-catalyzed click reaction, and their molecular assemblies in water and chloroform were studied. The amphiphiles exhibited a molecular orientation opposite to that of the conventional amphiphiles in each case. ζ Potential measurements indicated that the lipophilic ion part is exposed outside in chloroform. The size of a solvophobic part in the amphiphiles dominates the size of an assembling structure; that is, in water, these amphiphiles tethering different lengths of the saccharide part exhibited almost identical assembling size, whereas in chloroform, the size depends on the length of the saccharide part in the amphiphiles.

T1R3 homomeric sweet taste receptor regulates adipogenesis through Gαs-mediated microtubules disassembly and Rho activation in 3T3-L1 cells.

Directory of Open Access Journals (Sweden)

Yosuke Masubuchi

Full Text Available We previously reported that 3T3-L1 cells express a functional sweet taste receptor possibly as a T1R3 homomer that is coupled to Gs and negatively regulates adipogenesis by a Gαs-mediated but cAMP-independent mechanism. Here, we show that stimulation of this receptor with sucralose or saccharin induced disassembly of the microtubules in 3T3-L1 preadipocytes, which was attenuated by overexpression of the dominant-negative mutant of Gαs (Gαs-G226A. In contrast, overexpression of the constitutively active mutant of Gαs (Gαs-Q227L as well as treatment with cholera toxin or isoproterenol but not with forskolin caused disassembly of the microtubules. Sweetener-induced microtubule disassembly was accompanied by activation of RhoA and Rho-associated kinase (ROCK. This was attenuated with by knockdown of GEF-H1, a microtubule-localized guanine nucleotide exchange factor for Rho GTPase. Furthermore, overexpression of the dominant-negative mutant of RhoA (RhoA-T19N blocked sweetener-induced dephosphorylation of Akt and repression of PPARγ and C/EBPα in the early phase of adipogenic differentiation. These results suggest that the T1R3 homomeric sweet taste receptor negatively regulates adipogenesis through Gαs-mediated microtubule disassembly and consequent activation of the Rho/ROCK pathway.

Systems impacts of spent fuel disassembly alternatives

International Nuclear Information System (INIS)

1984-07-01

Three studies were completed to evaluate four alternatives to the disposal of intact spent fuel assemblies in a geologic repository. A preferred spent fuel waste form for disposal was recommended on consideration of (1) package design and fuel/package interaction, (2) long-term, in-repository performance of the waste form, and (3) overall process performance and costs for packaging, handling, and emplacement. The four basic alternative waste forms considered were (1) end fitting removal, (2) fission gas venting, (3) disassembly and close packing, and (4) shearing/immobilization. None of the findings ruled out any alternative on the basis of waste package considerations or long-term performance of the waste form. The third alternative offers flexibility in loading that may prove attractive in the various geologic media under consideration, greatly reduces the number of packages, and has the lowest unit cost. These studies were completed in October, 1981. Since then Westinghouse Electric Corporation and the Office of Nuclear Waste Isolation have completed studies in related fields. This report is now being published to provide publicly the background material that is contained within. 47 references, 28 figures, 31 tables

The development of underwater remote cutting method for the disassembling of rotary specimen rack KRR-1 and 2

Energy Technology Data Exchange (ETDEWEB)

Lee, D. K.; Jung, K. H.; Lee, K. W.; Oh, W. J. [KAERI, Taejon (Korea, Republic of); Lee, K. Y. [Korea Institute of Industrial Technology, Kwangju (Korea, Republic of)

2004-07-01

The Rotary Specimen Racks (RSRs) were highly activated and then classified intermediate level radioactive waste for the decommissioning of KRR-1anel2. The RSR can be treated as low level radioactive waste after removing stainless steel parts. To reduce the volume of intermediate level radioactive waste, underwater cutting is required to separate stainless steel parts from RSR because of high radioactivity. In this study, the automatic remote cutting method was developed to disassemble RSR under water. For automatic remote cutting processes, a CAM (Computer Aided Manufacturing) system is employed. A computer inputs NC (Numerical Control) codes to the controller, which are based on CAM model, and the controller instructs the equipment to process according to NC codes automatically. And the cutting force model was improved to cut RSR stably. The automatic cutting was conducted using imitation of RSR and then it was resulted that the developed automatic cutting method can be safely disassemble stainless steel parts of RSR under water.

Studies and research concerning BNFP design and construction of a spent-fuel disassembly/encapsulation system

International Nuclear Information System (INIS)

Dabolt, R.J.

1981-04-01

Commercial light water power reactor operation in the United States is developing a cumbersome inventory of spent fuel. Systems for interim storage and handling of this fuel are being developed by the Federal Government and industry. Disassembly and canning of the spent fuel elements is one of these systems. It has the potential to double the storage capacity of a prereprocessing storage facility or to triple the capacity of conventional shipping casks. Prototype equipment and controls required to perform this operation in a dry environment have been primarily designed and fabricated at the Barnwell Nuclear Fuel Plant (BNFP). Ridihalgh, Eggers, and Associates have provided design support and fabrication of the control system. This system is capable of extracting and canning the fuel pins and compacting the nonfuel-bearing components of spent fuel assemblies at processing rates of 10 to 12 assemblies per day. The process also provides the potential for enhanced inspection and assay of spent fuel by reducing the interference encountered from the high gamma fields of the nonfuel bearing hardware

Maintenance and disassembly considerations for the Technology Demonstration Facility

International Nuclear Information System (INIS)

Spampinato, P.T.

1983-01-01

The Technology Demonstration Facility (TDF) is a tandem-mirror design concept carried out under the direction of Lawrence Livermore National Laboratory. It was conceived as a near-term device with a mission of developing engineering technology in a D-T fusion environment. Overall maintenance and component disassembly were among the responsibilities of the Fusion Engineering Design Center (FEDC). A configuration evolved that was based on the operational requirements of the components, as well as the requirements for their replacements. Component lifetime estimates were used to estimate the frequency and the number of replacements. In addition, it was determined that the need for remote handling equipment followed within 1.5 years after initial start-up, emphasizing the direct relationship between developing maintenance scenarios/equipment and the device configuration. Many of the scheduled maintenance operations were investigated to first order, and preliminary handling equipment concepts were developed

Plastics disassembly versus bulk recycling: engineering design for end-of-life electronics resource recovery.

Science.gov (United States)

Rios, Pedro; Stuart, Julie Ann; Grant, Ed

2003-12-01

Annual plastic flows through the business and consumer electronics manufacturing supply chain include nearly 3 billion lb of high-value engineering plastics derived from petroleum. The recovery of resource value from this stream presents critical challenges in areas of materials identification and recycling process design that demand new green engineering technologies applied together with life cycle assessment and ecological supply chain analysis to create viable plastics-to-plastics supply cycles. The sustainable recovery of potentially high-value engineering plastics streams requires that recyclers either avoid mixing plastic parts or purify later by separating smaller plastic pieces created in volume reduction (shredding) steps. Identification and separation constitute significant barriers in the plastics-to-plastics recycling value proposition. In the present work, we develop a model that accepts randomly arriving electronic products to study scenarios by which a recycler might identify and separate high-value engineering plastics as well as metals. Using discrete eventsimulation,we compare current mixed plastics recovery with spectrochemical plastic resin identification and subsequent sorting. Our results show that limited disassembly with whole-part identification can produce substantial yields in separated streams of recovered engineering thermoplastics. We find that disassembly with identification does not constitute a bottleneck, but rather, with relatively few workers, can be configured to pull the process and thus decrease maximum staging space requirements.

Stimuli-disassembling gold nanoclusters for diagnosis of early stage oral cancer by optical coherence tomography

Science.gov (United States)

Kim, Chang Soo; Ingato, Dominique; Wilder-Smith, Petra; Chen, Zhongping; Kwon, Young Jik

2018-01-01

A key design consideration in developing contrast agents is obtaining distinct, multiple signal changes in diseased tissue. Plasmonic gold nanoparticles (Au NPs) have been developed as contrast agents due to their strong surface plasmon resonance (SPR). This study aims to demonstrate that stimuli-responsive plasmonic Au nanoclusters (Au NCs) can be used as a contrast agent for optical coherence tomography (OCT) in detecting early-stage cancer. Au NPs were clustered via acid-cleavable linkers to synthesize Au NCs that disassemble under mildly acidic conditions into individual Au NPs, simultaneously diminishing SPR effect (quantified by scattering intensity) and increasing Brownian motion (quantified by Doppler variance). The acid-triggered morphological and accompanying optico-physical property changes of the acid-disassembling Au NCs were confirmed by TEM, DLS, UV/Vis, and OCT. Stimuli-responsive Au NCs were applied in a hamster check pouch model carrying early-stage squamous carcinoma tissue. The tissue was visualized by OCT imaging, which showed reduced scattering intensity and increased Doppler variance in the dysplastic tissue. This study demonstrates the promise of diagnosing early-stage cancer using molecularly programmable, inorganic nanomaterial-based contrast agents that are capable of generating multiple, stimuli-triggered diagnostic signals in early-stage cancer.[Figure not available: see fulltext.

Technical review of WSRC-TR-93-614 criticality safety evaluation for disassembly basin sand filter

International Nuclear Information System (INIS)

Reed, R.L.

1994-01-01

The study documented in WSRC-TR-93-614 performed an evaluation of the criticality potential associated with the Disassembly Basin Sand Filter for K and L Areas. The document reviewed incorporated results of calculations documented in the engineering calculation N-CLC-K-00151. Analyses of the contents of disassembly basin sludge has indicated that the sludge contains fissile material in excess of subcritical mass limits as specified in ANSI/ANS standards. Previous studies had determined that the fissile material can not collect into a critical configuration in the basin. Since the sand filter is intended to remove suspended particles from the basin water and could serve as a mechanism to collect the fissile material into a critical configuration, the study examined conditions under which criticality could occur in the sand filter. The study shows that criticality is not considered possible in the sand filter. This review emphasized the technical accuracy and presentation of the evaluation. The evaluation was also examined for the elements required for NCSEs. The review was performed in accordance with the NRTSC technical review requirements and procedures and the E7 Manual technical review requirements. The technical review (per the E7 manual) of the engineering calculation (N-CLC-K-0 1 5 1) was previously performed by this reviewer

Spiropyran-Decorated SiO₂-Pt Janus Micromotor: Preparation and Light-Induced Dynamic Self-Assembly and Disassembly.

Science.gov (United States)

Zhang, Qilu; Dong, Renfeng; Chang, Xueyi; Ren, Biye; Tong, Zhen

2015-11-11

The controlled self-assembly of self-propelled Janus micromotors may give the micromotors some potential applications in many fields. In this work, we design a kind of SiO2-Pt Janus catalytic micromotor functionalized by spiropyran (SP) moieties on the surface of the SiO2 hemisphere. The spiropyran-modified SiO2-Pt Janus micromotor exhibits autonomous self-propulsion in the presence of hydrogen peroxide fuel in N,N-dimethylformamide (DMF)/H2O (1:1 in volume) mixture. We demonstrate that the self-propelled Janus micromotors can dynamically assemble into multiple motors because of the electrostatic attractions and π-π stacking between MC molecules induced by UV light irradiation (λ = 365 nm) and also quickly disassemble into mono motors when the light is switched to green light (λ = 520 nm) for the first time. Furthermore, the assembled Janus motors can move together automatically with different motion patterns propelled by the hydrogen peroxide fuels upon UV irradiation. The work provides a new approach not only to the development of the potential application of Janus motors but also to the fundamental science of reversible self-assembly and disassembly of Janus micromotors.

Alpha Decontamination and Disassembly Pilot Facility. Final report

International Nuclear Information System (INIS)

Daugherty, B.A.; Clark, H.E.

1985-04-01

The Alpha Decontamination and Disassembly (AD and D) Pilot Facility was built to develop and demonstrate a reference process for the decontamination and size reduction of noncombustible transuranic (TRU) waste. The goals of the reference process were to remove >99% of the surface contamination to the high-level waste tanks, and to achieve volume reduction factors greater than 15:1. Preliminary bench-scale decontamination work was accomplished at Savannah River Laboratory (SRL), establishing a reference decontamination process. Initially, the pilot facility did not achieve the decontamination goals. As the program continued, and modifications to the process were made, coupon analysis idicated that 99% of the surface contamination was removed to the high-level drain system. Prior to the AD and D Pilot Facility, no size reduction work had been done at SRL. Several other Department of Energy (DOE) facilities were experimenting with plasma arc torches for size reduction work. Their methods were employed in the AD and D hot cell with moderate success. The experimental work concluded with recommendations for further testing of other size reduction techniques. 11 figs., 6 tabs

Cesium removal from the fuel storage water at the Savannah River Site R-Building Disassembly Basin using 3M Empore reg-sign-membrane filter technology

International Nuclear Information System (INIS)

Oji, L.N.; Thompson, M.C.; Peterson, K.; May, C.; Kafka, T.M.

1998-01-01

This report describes results from a seven-day demonstration of the use of 3M Empore membrane filter loaded with ion exchange material (potassium cobalt hexacynoferrate (CoHex)) for cesium uptake from the R-Disassembly Basin at the Savannah River Site. The goal of the demonstration was to evaluate the ability of the Process Absorber Development unit (PADU), a water pre-filtration /CoHex configuration on a skid, to remove cesium from R-Disassembly Basin at a linear processing flow rate of 22.7 liters per minute (1,195.8 liters/minute/m 2 or 29.35 gallons/minute/ft 2 ). Over 210,000 liters (> 55,500 gallons) of R-Disassembly Basin water was processed through the PADU without a cesium breakthrough, that is, the effluent after treatment with CoHex, contained less than detectable amounts of radioactive cesium. Some of the observed advantages of the Empore membrane filter technology over conventional packed column ion exchange systems includes rapid flow rates without channeling effects, low volume secondary waste and fast extraction or rapid kinetics per unit of flow

Introductory Education for Mechanical Engineering by Exercise in Mechanical Disassembly

Science.gov (United States)

Matsui, Yoshio; Asakawa, Naoki; Iwamori, Satoru

An introductory program “Exercise for engineers in mechanical disassembly” is an exercise that ten students of every team disassemble a motor scooter to the components and then assemble again to the initial form in 15 weeks. The purpose of this program is to introduce mechanical engineering by touching the real machine and learning how it is composed from various mechanical parts to the students at the early period after the entrance into the university. Additional short lectures by young teachers and a special lecture by a top engineer in the industry encourage the students to combine the actual machine and the mechanical engineering subjects. Furthermore, various educations such as group leader system, hazard prediction training, parts filing are included in this program. As a result, students recognize the importance of the mechanical engineering study and the way of group working.

ARC: A compact, high-field, disassemblable fusion nuclear science facility and demonstration power plant

Science.gov (United States)

Sorbom, Brandon; Ball, Justin; Palmer, Timothy; Mangiarotti, Franco; Sierchio, Jennifer; Bonoli, Paul; Kasten, Cale; Sutherland, Derek; Barnard, Harold; Haakonsen, Christian; Goh, Jon; Sung, Choongki; Whyte, Dennis

2014-10-01

The Affordable, Robust, Compact (ARC) reactor conceptual design aims to reduce the size, cost, and complexity of a combined Fusion Nuclear Science Facility (FNSF) and demonstration fusion pilot power plant. ARC is a 270 MWe tokamak reactor with a major radius of 3.3 m, a minor radius of 1.1 m, and an on-axis magnetic field of 9.2 T. ARC has Rare Earth Barium Copper Oxide (REBCO) superconducting toroidal field coils with joints to allow disassembly, allowing for removal and replacement of the vacuum vessel as a single component. Inboard-launched current drive of 25 MW LHRF power and 13.6 MW ICRF power is used to provide a robust, steady state core plasma far from disruptive limits. ARC uses an all-liquid blanket, consisting of low pressure, slowly flowing Fluorine Lithium Beryllium (FLiBe) molten salt. The liquid blanket acts as a working fluid, coolant, and tritium breeder, and minimizes the solid material that can become activated. The large temperature range over which FLiBe is liquid permits blanket operation at 800-900 K with single phase fluid cooling and allows use of a high-efficiency Brayton cycle for electricity production in the secondary coolant loop.

KADIS: a program to analyse the disassembly phase of hypothetical accidents in LMFBRs

International Nuclear Information System (INIS)

Schmuck, P.; Jacobs, G.; Arnecke, G.

1977-11-01

The program KADIS models the disassembly phase during power excursions in LMFBR hypothetical accidents. KADIS is based on point kinetics in the neutronics part and on a 2-dimensional representation of the reactor core in the hydrodynamics part. The core is modeled as an ideal, compressible fluid which is heated up adiabatically during the excursion. KADIS was built up with the help of the VENUS program of Argonne National Laboratory. Several important features were added to the basic VENUS model. Therefore we give first a complete description of the mathematical models used. Secondly we provide the user with the necessary information to handle the input/output of KADIS. (orig.) [de

Authorized Limits for the Release of a 25 Ton Locomotive, Serial Number 21547, at the Area 25 Engine Maintenance, Assembly, and Disassembly Facility, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

Gwin, Jeremy; Frenette, Douglas

2010-01-01

This document contains process knowledge and radiological data and analysis to support approval for release of the 25-ton locomotive, Serial Number 21547, at the Area 25 Engine Maintenance, Assembly, and Disassembly (EMAD) Facility, located on the Nevada Test Site (NTS). The 25-ton locomotive is a small, one-of-a-kind locomotive used to move railcars in support of the Nuclear Engine for Rocket Vehicle Application project. This locomotive was identified as having significant historical value by the Nevada State Railroad Museum in Boulder City, Nevada, where it will be used as a display piece. A substantial effort to characterize the radiological conditions of the locomotive was undertaken by the NTS Management and Operations Contractor, National Security Technologies, LLC (NSTec). During this characterization process, seven small areas on the locomotive had contamination levels that exceeded the NTS release criteria (limits consistent with U.S. Department of Energy (DOE) Order DOE O 5400.5, 'Radiation Protection of the Public and the Environment'). The decision was made to perform radiological decontamination of these known accessible impacted areas to further the release process. On February 9, 2010, NSTec personnel completed decontamination of these seven areas to within the NTS release criteria. Although all accessible areas of the locomotive had been successfully decontaminated to within NTS release criteria, it was plausible that inaccessible areas of the locomotive (i.e., those areas on the locomotive where it was not possible to perform radiological surveys) could potentially have contamination above unrestricted release limits. To access the majority of these inaccessible areas, the locomotive would have to be disassembled. A complete disassembly for a full radiological survey could have permanently destroyed parts and would have ruined the historical value of the locomotive. Complete disassembly would also add an unreasonable financial burden for the

Reducing environmental burdens of solid-state lighting through end-of-life design

International Nuclear Information System (INIS)

Hendrickson, C T; Matthews, D H; Ashe, M; Jaramillo, P; McMichael, F C

2010-01-01

With 20% of US electricity used for lighting, energy efficient solid-state lighting technology could have significant benefits. While energy efficiency in use is important, the life cycle cost, energy and environmental impacts of light-emitting diode (LED) solid-state lighting could be reduced by reusing, remanufacturing or recycling components of the end products. Design decisions at this time for the nascent technology can reduce material and manufacturing burdens by considering the ease of disassembly, potential for remanufacturing, and recovery of parts and materials for reuse and recycling. We use teardowns of three commercial solid-state lighting products designed to fit in conventional Edison light bulb sockets to analyze potential end-of-life reuse strategies for solid-state lighting and recommend strategies for the industry. Current lamp designs would benefit from standardization of part connections to facilitate disassembly and remanufacturing of components, and fewer material types in structural pieces to maximize homogeneous materials recovery. The lighting industry should also start now to develop an effective product take-back system for collecting future end-of-life products.

Reducing environmental burdens of solid-state lighting through end-of-life design

Energy Technology Data Exchange (ETDEWEB)

Hendrickson, C T; Matthews, D H; Ashe, M; Jaramillo, P; McMichael, F C, E-mail: cth@cmu.ed [Green Design Institute, Carnegie Mellon University (United States)

2010-01-15

With 20% of US electricity used for lighting, energy efficient solid-state lighting technology could have significant benefits. While energy efficiency in use is important, the life cycle cost, energy and environmental impacts of light-emitting diode (LED) solid-state lighting could be reduced by reusing, remanufacturing or recycling components of the end products. Design decisions at this time for the nascent technology can reduce material and manufacturing burdens by considering the ease of disassembly, potential for remanufacturing, and recovery of parts and materials for reuse and recycling. We use teardowns of three commercial solid-state lighting products designed to fit in conventional Edison light bulb sockets to analyze potential end-of-life reuse strategies for solid-state lighting and recommend strategies for the industry. Current lamp designs would benefit from standardization of part connections to facilitate disassembly and remanufacturing of components, and fewer material types in structural pieces to maximize homogeneous materials recovery. The lighting industry should also start now to develop an effective product take-back system for collecting future end-of-life products.

Nuclear disassembly of the (Pb+Au) system at Elab=29 MeV per nucleon

International Nuclear Information System (INIS)

Piasecki, E.; Kordyasz, A.; Bresson, S.; Crema, E.; Galin, J.; Guerreau, D.; Morjean, M.; Paulot, C.; Pouthas, J.; Jastrzebski, J.; Pienkowski, L.; Skulski, W.; Lott, B.; Quednau, B.; Schroder, W.U.; Toeke, J.

1990-01-01

Nuclei, with Z up to 82, emitted in the 208 Pb+ 197 Au reaction at E lab =29 MeV per nucleon, have been measured as a function of the associated neutron multiplicity. The data reveal the presence of strong correlations between character of a collision and neutron multiplicity. The trends suggest a disassembly of the nuclear system into a large number of nucleons and small fragments in the events with the highest neutron multiplicity. In such events, approximately one third of the neutrons are released from the system and fragments yields decrease in an exponential fashion with increasing mass

FaCT phase-I evaluation on the advanced aqueous reprocessing process (2). Development of mechanical disassembly and short stroke shearing systems for FBR fuel reprocessing

International Nuclear Information System (INIS)

Takeuchi, Masayuki; Kitagaki, Toru; Higuchi, Hidetoshi; Fukushima, Mineo; Washiya, Tadahiro; Kobayashi, Tsuguyuki

2011-01-01

JAEA promotes a development of an advanced head-end process in FaCT project. We selected mechanical cutting method for disassembly process and short stroke method for shearing process. In the FaCT phase-I, the criteria was set for decision about the innovative technology and some fundamental performances of the innovative technology such as precision, speed, durability, operation performance and system concept were discussed by the engineering test and design work. We designed and fabricated an engineering-scale test device for mechanical disassembly and short stroke shearing and have carried out the engineering tests using simulated fuel assemblies. As a part of the engineering test results, the effects of cutting conditions on the durability of cutting tool and cutting stability were discussed. Also, the reduction of magazine width is effective to improve the precision of sheared pin length, and the bundle of simulated fuel pins were successfully sheared to 10 ± 5mm, which is a target for the sheared pin length. The criteria for the mechanical disassembly technology and the short stroke shearing technology were satisfied, so we judged that the development of innovative technologies has worth going on for the next phase in the FaCT project. (author)

Electrostatic assembly/disassembly of nanoscaled colloidosomes for light-triggered cargo release

KAUST Repository

Li, Song

2015-04-27

Colloidosome capsules possess the potential for the encapsulation and release of molecular and macromolecular cargos. However, the stabilization of the colloidosome shell usually requires an additional covalent crosslinking which irreversibly seals the capsules, and greatly limits their applications in large-cargos release. Herein we report nanoscaled colloidosomes designed by the electrostatic assembly of organosilica nanoparticles (NPs) with oppositely charged surfaces (rather than covalent bonds), arising from different contents of a bridged nitrophenylene-alkoxysilane [NB; 3-nitro-N-(3-(triethoxysilyl)propyl)-4-(((3-(triethoxysilyl)propyl)-amino)methyl)benzamid] derivative in the silica. The surface charge of the positively charged NPs was reversed by light irradiation because of a photoreaction in the NB moieties, which impacted the electrostatic interactions between NPs and disassembled the colloidosome nanosystems. This design was successfully applied for the encapsulation and light-triggered release of cargos. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Role of Melatonin in Cell-Wall Disassembly and Chilling Tolerance in Cold-Stored Peach Fruit.

Science.gov (United States)

Cao, Shifeng; Bian, Kun; Shi, Liyu; Chung, Hsiao-Hang; Chen, Wei; Yang, Zhenfeng

2018-06-06

Melatonin reportedly increases chilling tolerance in postharvest peach fruit during cold storage, but information on its effects on cell-wall disassembly in chilling-injured peaches is limited. In this study, we investigated the role of cell-wall depolymerization in chilling-tolerance induction in melatonin-treated peaches. Treatment with 100 μM melatonin alleviated chilling symptoms (mealiness) characterized by a decrease in fruit firmness and increase in juice extractability in treated peaches during storage. The loss of neutral sugars, such as arabinose and galactose, in both the 1,2-cyclohexylenedinitrilotetraacetic acid (CDTA)- and Na 2 CO 3 -soluble fractions was observed at 7 days in treated peaches, but the contents increased after 28 days of storage. Atomic-force-microscopy (AFM) analysis revealed that the polysaccharide widths in the CDTA- and Na 2 CO 3 -soluble fractions in the treated fruit were mainly distributed in a shorter range, as compared with those in the control fruit. In addition, the expression profiles of a series of cell-wall-related genes showed that melatonin treatment maintained the balance between transcripts of PpPME and PpPG, which accompany the up-regulation of several other genes involved in cell-wall disassembly. Taken together, our results suggested that the reduced mealiness by melatonin was probably associated with its positive regulation of numerous cell-wall-modifying enzymes and proteins; thus, the depolymerization of the cell-wall polysaccharides in the peaches treated with melatonin was maintained, and the treated fruit could soften gradually during cold storage.

Characterization of spent fuel disassembly hardware and nonfuel bearing components and their relationship to 10 CFR 61

International Nuclear Information System (INIS)

Luksic, A.T.

1987-02-01

There are a variety of wastes that will be disposed of by the federal waste management system under the Nuclear Waste Policy Act of 1982. The primary waste form is spent nuclear fuel. Currently, this is in the form of fuel assemblies. If the fuel pins are removed from the fuel assembly, as in consolidation, then the fuel pins and the structural portion of the fuel assembly must be considered as separate waste streams. The structural hardware consists of end fittings, grid spacers, water rods (BWR 8 x 8 only), control rod guide tubes (PWR only) and various nuts, washers, springs, etc. These are referred to as spent fuel disassembly (SFD) hardware. There will also be a number of other components which are defined in Appendix E of 10 CFR 961, the standard utility contract. These are referred to as nonfuel-bearing (NFB) components, and include fuel channels (BWR), control rods, fission chambers, neutron sources, thimble plugs, and other components. This paper characterizes spent fuel disassembly (SFD) hardware, and nonfuel-bearing (NFB) components for the most abundant fuel types. The descriptions and figures given are representative for the items described. Many subvariants exist due to design evaluation, which are not covered. This paper also discusses the relationship of these wastes to 10 CFR 61 waste classification

Present state and subjects for hereafter of technical development for decommissioning

International Nuclear Information System (INIS)

Ishikura, Takeshi; Onozawa, Teruo; Saishu, Sadanori

1997-01-01

As to the decommissioning of nuclear power facilities, it was confirmed that there is no technical problem which makes decommissioning impossible in the report of the nuclear power subcommittee of Advisory Committee for Energy. In OECD/NEA, the international joint research for exchanging the information and experience of the decommissioning projects has been carried out. In foreign countries, the decommissioning has been executed practically. As the disassembling techniques for structures, laser cutting, plasma are cutting, arc gouging and gas cutting, arc saw cutting, gas cutting and powder gas cutting, mechanical cutting and molded explosive cutting are described. As the disassembling techniques for concrete structures, diamond wire saw method, mechanical cutting, water jet cutting and the method of using disk cutter and mechanical wedge are described. As to decontamination techniques, decontamination before disassembling, decontamination of large equipment, and decontamination after disassembling by blast, electrolysis and chemical immersion are described. The technology for measuring the radiation before disassembling and the radiation of buildings and disassembled waste is reported. (K.I.)

Cofilin phosphorylation is elevated after F-actin disassembly induced by Rac1 depletion

DEFF Research Database (Denmark)

Liu, Linna; Li, Jing; Zhang, Liwang

2015-01-01

Cytoskeletal reorganization is essential to keratinocyte function. Rac1 regulates cytoskeletal reorganization through signaling pathways such as the cofilin cascade. Cofilin severs actin filaments after activation by dephosphorylation. Rac1 was knocked out in mouse keratinocytes and it was found...... that actin filaments disassembled. In the epidermis of mice in which Rac1 was knocked out only in keratinocytes, cofilin phosphorylation was aberrantly elevated, corresponding to repression of the phosphatase slingshot1 (SSH1). These effects were independent of the signaling pathways for p21-activated kinase....../LIM kinase (Pak/LIMK), protein kinase C, or protein kinase D or generation of reactive oxygen species. Similarly, when actin polymerization was specifically inhibited or Rac1 was knocked down, cofilin phosphorylation was enhanced and SSH1 was repressed. Repression of SSH1 partially blocked actin...

Assembly/disassembly of a complex icosahedral virus to incorporate heterologous nucleic acids

Science.gov (United States)

Pascual, Elena; Mata, Carlos P.; Carrascosa, José L.; Castón, José R.

2017-12-01

Hollow protein containers are widespread in nature, and include virus capsids as well as eukaryotic and bacterial complexes. Protein cages are studied extensively for applications in nanotechnology, nanomedicine and materials science. Their inner and outer surfaces can be modified chemically or genetically, and the internal cavity can be used to template, store and/or arrange molecular cargos. Virus capsids and virus-like particles (VLP, noninfectious particles) provide versatile platforms for nanoscale bioengineering. Study of capsid protein self-assembly into monodispersed particles, and of VLP structure and biophysics is necessary not only to understand natural processes, but also to infer how these platforms can be redesigned to furnish novel functional VLP. Here we address the assembly dynamics of infectious bursal disease virus (IBDV), a complex icosahedral virus. IBDV has a ~70 nm-diameter T  =  13 capsid with VP2 trimers as the only structural subunits. During capsid assembly, VP2 is synthesized as a precursor (pVP2) whose C terminus is cleaved. The pVP2 C terminus has an amphipathic helix that controls VP2 polymorphism. In the absence of the VP3 scaffolding protein, necessary for control of assembly, 466/456-residue pVP2 intermediates bearing this helix assemble into VLP only when expressed with an N-terminal His6 tag (the HT-VP2-466 protein). HT-VP2-466 capsids are optimal for genetic insertion of proteins (cargo space ~78 000 nm3). We established an in vitro assembly/disassembly system of HT-VP2-466-based VLP for heterologous nucleic acid packaging and/or encapsulation of drugs and other molecules. HT-VP2-466 (empty) capsids were disassembled and reassembled by dialysis against low-salt/basic pH and high-salt/acid pH buffers, respectively, thus illustrating the reversibility in vitro of IBDV capsid assembly. HT-VP2-466 VLP also packed heterologous DNA by non-specific confinement during assembly. These and previous results establish the bases

Selective maintenance of multi-state systems with structural dependence

International Nuclear Information System (INIS)

Dao, Cuong D.; Zuo, Ming J.

2017-01-01

This paper studies the selective maintenance problem for multi-state systems with structural dependence. Each component can be in one of multiple working levels and several maintenance actions are possible to a component in a maintenance break. The components structurally form multiple hierarchical levels and dependence groups. A directed graph is used to represent the precedence relations of components in the system. A selective maintenance optimization model is developed to maximize the system reliability in the next mission under time and cost constraints. A backward search algorithm is used to determine the assembly sequence for a selective maintenance scenario. The maintenance model helps maintenance managers in determining the best combination of maintenance activities to maximize the probability of successfully completing the next mission. Examples showing the use of the proposed method are presented. - Highlights: • A selective maintenance model for multi-state systems is proposed considering both economic and structural dependence. • Structural dependence is modeled as precedence relationship when disassembling components for maintenance. • Resources for disassembly and maintenance are evaluated using a backward search algorithm. • Maintenance strategies with and without structural dependence are analyzed. • Ignoring structural dependence may lead to over-estimation of system reliability.

LRRK2 phosphorylates pre-synaptic N-ethylmaleimide sensitive fusion (NSF) protein enhancing its ATPase activity and SNARE complex disassembling rate.

Science.gov (United States)

Belluzzi, Elisa; Gonnelli, Adriano; Cirnaru, Maria-Daniela; Marte, Antonella; Plotegher, Nicoletta; Russo, Isabella; Civiero, Laura; Cogo, Susanna; Carrion, Maria Perèz; Franchin, Cinzia; Arrigoni, Giorgio; Beltramini, Mariano; Bubacco, Luigi; Onofri, Franco; Piccoli, Giovanni; Greggio, Elisa

2016-01-13

Lrrk2, a gene linked to Parkinson's disease, encodes a large scaffolding protein with kinase and GTPase activities implicated in vesicle and cytoskeletal-related processes. At the presynaptic site, LRRK2 associates with synaptic vesicles through interaction with a panel of presynaptic proteins. Here, we show that LRRK2 kinase activity influences the dynamics of synaptic vesicle fusion. We therefore investigated whether LRRK2 phosphorylates component(s) of the exo/endocytosis machinery. We have previously observed that LRRK2 interacts with NSF, a hexameric AAA+ ATPase that couples ATP hydrolysis to the disassembling of SNARE proteins allowing them to enter another fusion cycle during synaptic exocytosis. Here, we demonstrate that NSF is a substrate of LRRK2 kinase activity. LRRK2 phosphorylates full-length NSF at threonine 645 in the ATP binding pocket of D2 domain. Functionally, NSF phosphorylated by LRRK2 displays enhanced ATPase activity and increased rate of SNARE complex disassembling. Substitution of threonine 645 with alanine abrogates LRRK2-mediated increased ATPase activity. Given that the most common Parkinson's disease LRRK2 G2019S mutation displays increased kinase activity, our results suggest that mutant LRRK2 may impair synaptic vesicle dynamics via aberrant phosphorylation of NSF.

TRIM15 is a focal adhesion protein that regulates focal adhesion disassembly

Science.gov (United States)

Uchil, Pradeep D.; Pawliczek, Tobias; Reynolds, Tracy D.; Ding, Siyuan; Hinz, Angelika; Munro, James B.; Huang, Fang; Floyd, Robert W.; Yang, Haitao; Hamilton, William L.; Bewersdorf, Joerg; Xiong, Yong; Calderwood, David A.; Mothes, Walther

2014-01-01

ABSTRACT Focal adhesions are macromolecular complexes that connect the actin cytoskeleton to the extracellular matrix. Dynamic turnover of focal adhesions is crucial for cell migration. Paxillin is a multi-adaptor protein that plays an important role in regulating focal adhesion dynamics. Here, we identify TRIM15, a member of the tripartite motif protein family, as a paxillin-interacting factor and a component of focal adhesions. TRIM15 localizes to focal contacts in a myosin-II-independent manner by an interaction between its coiled-coil domain and the LD2 motif of paxillin. Unlike other focal adhesion proteins, TRIM15 is a stable focal adhesion component with restricted mobility due to its ability to form oligomers. TRIM15-depleted cells display impaired cell migration and reduced focal adhesion disassembly rates, in addition to enlarged focal adhesions. Thus, our studies demonstrate a cellular function for TRIM15 as a regulatory component of focal adhesion turnover and cell migration. PMID:25015296

AGR-3/4 Irradiation Test Train Disassembly and Component Metrology First Look Report

Energy Technology Data Exchange (ETDEWEB)

Stempien, John Dennis [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rice, Francine Joyce [Idaho National Lab. (INL), Idaho Falls, ID (United States); Harp, Jason Michael [Idaho National Lab. (INL), Idaho Falls, ID (United States); Winston, Philip Lon [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-09-01

The AGR-3/4 experiment was designed to study fission product transport within graphitic matrix material and nuclear-grade graphite. To this end, this experiment consisted of 12 capsules, each fueled with 4 compacts containing UCO TRISO particles as driver fuel and 20 UCO designed-to-fail (DTF) fuel particles in each compact. The DTF fuel was fabricated with a thin pyrocarbon layer which was intended to fail during irradiation and provide a source of fission products. These fission products could then migrate through the compact and into the surrounding concentric rings of graphitic matrix material and/or nuclear graphite. Through post-irradiation examination (PIE) of the rings (including physical sampling and gamma scanning) fission product concentration profiles within the rings can be determined. These data can be used to elucidate fission product transport parameters (e.g. diffusion coefficients within the test materials) which will be used to inform and refine models of fission product transport. After irradiation in the Advanced Test Reactor (ATR) had been completed in April 2014, the AGR-3/4 experiment was shipped to the Hot Fuel Examination Facility (HFEF) at the Materials and Fuels Complex (MFC) for inspection, disassembly, and metrology. The AGR-3/4 test train was received at MFC in two separate shipments between February and April 2015. Visual examinations of the test train exterior did not indicate dimensional distortion, and only two small discolored areas were observed at the bottom of Capsules 8 and 9. No corresponding discoloration was found on the inside of these capsules, however. Prior to disassembly, the two test train sections were subject to analysis via the Precision Gamma Scanner (PGS), which did not indicate that any gross fuel relocation had occurred. A series of specialized tools (including clamps, cutters, and drills) had been designed and fabricated in order to carry out test train disassembly and recovery of capsule components (graphite

AGR-3/4 Irradiation Test Train Disassembly and Component Metrology First Look Report

Energy Technology Data Exchange (ETDEWEB)

Stempien, John Dennis [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rice, Francine Joyce [Idaho National Lab. (INL), Idaho Falls, ID (United States); Harp, Jason Michael [Idaho National Lab. (INL), Idaho Falls, ID (United States); Winston, Philip Lon [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-03-01

The AGR-3/4 experiment was designed to study fission product transport within graphitic matrix material and nuclear-grade graphite. To this end, this experiment consisted of 12 capsules, each fueled with 4 compacts containing UCO TRISO particles as driver fuel and 20 UCO designed-to-fail (DTF) fuel particles in each compact. The DTF fuel was fabricated with a thin pyrocarbon layer which was intended to fail during irradiation and provide a source of fission products. These fission products could then migrate through the compact and into the surrounding concentric rings of graphitic matrix material and/or nuclear graphite. Through post-irradiation examination (PIE) of the rings (including physical sampling and gamma scanning) fission product concentration profiles within the rings can be determined. These data can be used to elucidate fission product transport parameters (e.g. diffusion coefficients within the test materials) which will be used to inform and refine models of fission product transport. After irradiation in the Advanced Test Reactor (ATR) had been completed in April 2014, the AGR-3/4 experiment was shipped to the Hot Fuel Examination Facility (HFEF) at the Materials and Fuels Complex (MFC) for inspection, disassembly, and metrology. The AGR-3/4 test train was received at MFC in two separate shipments between February and April 2015. Visual examinations of the test train exterior did not indicate dimensional distortion, and only two small discolored areas were observed at the bottom of Capsules 8 and 9. No corresponding discoloration was found on the inside of these capsules, however. Prior to disassembly, the two test train sections were subject to analysis via the Precision Gamma Scanner (PGS), which did not indicate that any gross fuel relocation had occurred. A series of specialized tools (including clamps, cutters, and drills) had been designed and fabricated in order to carry out test train disassembly and recovery of capsule components (graphite

Neuroprotective Effects against POCD by Photobiomodulation: Evidence from Assembly/Disassembly of the Cytoskeleton

Directory of Open Access Journals (Sweden)

Ann D. Liebert

2016-01-01

Full Text Available Postoperative cognitive dysfunction (POCD is a decline in memory following anaesthesia and surgery in elderly patients. While often reversible, it consumes medical resources, compromises patient well-being, and possibly accelerates progression into Alzheimer's disease. Anesthetics have been implicated in POCD, as has neuroinflammation, as indicated by cytokine inflammatory markers. Photobiomodulation (PBM is an effective treatment for a number of conditions, including inflammation. PBM also has a direct effect on microtubule disassembly in neurons with the formation of small, reversible varicosities, which cause neural blockade and alleviation of pain symptoms. This mimics endogenously formed varicosities that are neuroprotective against damage, toxins, and the formation of larger, destructive varicosities and focal swellings. It is proposed that PBM may be effective as a preconditioning treatment against POCD; similar to the PBM treatment, protective and abscopal effects that have been demonstrated in experimental models of macular degeneration, neurological, and cardiac conditions.

The Chloroplast Division Protein ARC6 Acts to Inhibit Disassembly of GDP-bound FtsZ2.

Science.gov (United States)

Sung, Min Woo; Shaik, Rahamthulla; TerBush, Allan D; Osteryoung, Katherine W; Vitha, Stanislav; Holzenburg, Andreas

2018-05-16

Chloroplasts host photosynthesis and fulfill other metabolic functions that are essential to plant life. They have to divide by binary fission to maintain their numbers throughout cycles of cell division. Chloroplast division is achieved by a complex ring-shaped division machinery located on both the inner (stromal) and the outer (cytosolic) side of the chloroplast envelope. The inner division ring (termed the Z ring) is formed by the assembly of tubulin-like FtsZ1 and FtsZ2 proteins. ARC6 is a key chloroplast division protein that interacts with the Z ring. ARC6 spans the inner envelope membrane, is known to stabilize or maintain the Z ring, and anchors the Z ring to the inner membrane through interaction with FtsZ2. The underlying mechanism of Z-ring stabilization is not well understood. Here, biochemical and structural characterization of ARC6 was conducted using light scattering, sedimentation, and light and transmission electron microscopy. The recombinant protein was purified as a dimer. The results indicated that a truncated form of ARC6 (tARC6), representing the stromal portion of ARC6, affects FtsZ2 assembly without forming higher-order structures, and exerts its effect via FtsZ2 dynamics. tARC6 prevented GDP-induced FtsZ2 disassembly and caused a significant net increase in FtsZ2 assembly when GDP was present. Single particle analysis and 3D reconstruction were performed to elucidate the structural basis of ARC6 activity. Together, the data reveal that a dimeric form of tARC6 binds to FtsZ2 filaments and does not increase FtsZ polymerization rates but rather inhibits GDP-associated FtsZ2 disassembly. Published under license by The American Society for Biochemistry and Molecular Biology, Inc.

Expert System analysis of non-fuel assembly hardware and spent fuel disassembly hardware: Its generation and recommended disposal

International Nuclear Information System (INIS)

Williamson, D.A.

1991-01-01

Almost all of the effort being expended on radioactive waste disposal in the United States is being focused on the disposal of spent Nuclear Fuel, with little consideration for other areas that will have to be disposed of in the same facilities. one area of radioactive waste that has not been addressed adequately because it is considered a secondary part of the waste issue is the disposal of the various Non-Fuel Bearing Components of the reactor core. These hardware components fall somewhat arbitrarily into two categories: Non-Fuel Assembly (NFA) hardware and Spent Fuel Disassembly (SFD) hardware. This work provides a detailed examination of the generation and disposal of NFA hardware and SFD hardware by the nuclear utilities of the United States as it relates to the Civilian Radioactive Waste Management Program. All available sources of data on NFA and SFD hardware are analyzed with particular emphasis given to the Characteristics Data Base developed by Oak Ridge National Laboratory and the characterization work performed by Pacific Northwest Laboratories and Rochester Gas ampersand Electric. An Expert System developed as a portion of this work is used to assist in the prediction of quantities of NFA hardware and SFD hardware that will be generated by the United States' utilities. Finally, the hardware waste management practices of the United Kingdom, France, Germany, Sweden, and Japan are studied for possible application to the disposal of domestic hardware wastes. As a result of this work, a general classification scheme for NFA and SFD hardware was developed. Only NFA and SFD hardware constructed of zircaloy and experiencing a burnup of less than 70,000 MWD/MTIHM and PWR control rods constructed of stainless steel are considered Low-Level Waste. All other hardware is classified as Greater-ThanClass-C waste

Chain Assembly and Disassembly Processes Differently Affect the Conformational Space of Ubiquitin Chains.

Science.gov (United States)

Kniss, Andreas; Schuetz, Denise; Kazemi, Sina; Pluska, Lukas; Spindler, Philipp E; Rogov, Vladimir V; Husnjak, Koraljka; Dikic, Ivan; Güntert, Peter; Sommer, Thomas; Prisner, Thomas F; Dötsch, Volker

2018-02-06

Ubiquitination is the most versatile posttranslational modification. The information is encoded by linkage type as well as chain length, which are translated by ubiquitin binding domains into specific signaling events. Chain topology determines the conformational space of a ubiquitin chain and adds an additional regulatory layer to this ubiquitin code. In particular, processes that modify chain length will be affected by chain conformations as they require access to the elongation or cleavage sites. We investigated conformational distributions in the context of chain elongation and disassembly using pulsed electron-electron double resonance spectroscopy in combination with molecular modeling. Analysis of the conformational space of diubiquitin revealed conformational selection or remodeling as mechanisms for chain recognition during elongation or hydrolysis, respectively. Chain elongation to tetraubiquitin increases the sampled conformational space, suggesting that a high intrinsic flexibility of K48-linked chains may contribute to efficient proteasomal degradation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Disassembly of an arch bridge deformed due to landslide activity and the replacement of a new bridge in the same site. Jisuberi ni yori henkei shita arch bashi no kaitai to shinbashi no kakekae

Energy Technology Data Exchange (ETDEWEB)

Sano, S; Morimoto, C; Tomoda, T; Mizukawa, Y; Onushi, M; Ito, T [Kawasaki Heavy Industries, Ltd., Tokyo (Japan)

1991-10-20

This report describes the replacement process of an arch bridge deformed due to landslide activity, selection and contents of the disassembly method, and configuration of the new bridge and its design method. The Ryugu Bridge had been damaged by landslides over an extended period. It was a deck arch bridge having originally a span of 74 meters, but it had shortened by 424 mm due to landslide activity during 14 years since its completion. Then it was decided to be replaced by a new bridge having an adjustable structure to support the movement of its abutments. As disassembly of the deformed arch bridge could be dangerous, the best methodology was studied, and the disassembly was carried out by the cable method. The new bridge had box-girder parts in both side of the main truss, so as to be adjustable to the change of the span length, and the bridge was designed for a working life of 50 years if the bearing supports and expansion joints were reset every 10 years. Concerning the connecting parts between the box-girder and the main truss, appropriateness of the sectional configuration was verified by FEM analysis. 9 refs., 18 figs., 2 tab.

Acoustically Triggered Disassembly of Multilayered Polyelectrolyte Thin Films through Gigahertz Resonators for Controlled Drug Release Applications

Directory of Open Access Journals (Sweden)

Zhixin Zhang

2016-11-01

Full Text Available Controlled drug release has a high priority for the development of modern medicine and biochemistry. To develop a versatile method for controlled release, a miniaturized acoustic gigahertz (GHz resonator is designed and fabricated which can transfer electric supply to mechanical vibrations. By contacting with liquid, the GHz resonator directly excites streaming flows and induces physical shear stress to tear the multilayered polyelectrolyte (PET thin films. Due to the ultra-high working frequency, the shear stress is greatly intensified, which results in a controlled disassembling of the PET thin films. This technique is demonstrated as an effective method to trigger and control the drug release. Both theory analysis and controlled release experiments prove the thin film destruction and the drug release.

Improvement of the in vivo cellular repopulation of decellularized cardiovascular tissues by a detergent-free, non-proteolytic, actin-disassembling regimen.

Science.gov (United States)

Assmann, Alexander; Struß, Marc; Schiffer, Franziska; Heidelberg, Friederike; Munakata, Hiroshi; Timchenko, Elena V; Timchenko, Pavel E; Kaufmann, Tim; Huynh, Khon; Sugimura, Yukiharu; Leidl, Quentin; Pinto, Antonio; Stoldt, Volker R; Lichtenberg, Artur; Akhyari, Payam

2017-12-01

Low immunogenicity and high repopulation capacity are crucial determinants for the functional and structural performance of acellular cardiovascular implants. The present study evaluates a detergent-free, non-proteolytic, actin-disassembling regimen (BIO) for decellularization of heart valve and vessel grafts, particularly focusing on their bio-functionality. Rat aortic conduits (rAoC; n = 89) and porcine aortic valve samples (n = 106) are decellularized using detergents (group DET) or the BIO regimen. BIO decellularization results in effective elimination of cellular proteins and significantly improves removal of DNA as compared with group DET, while the extracellular matrix (ECM) structure as well as mechanical properties are preserved. The architecture of rAoC in group BIO allows for improved bio-functionalization with fibronectin (FN) in a standardized rat implantation model: BIO treatment significantly increases speed and amount of autologous medial cellular repopulation in vivo (p < 0.001) and decreases the formation of hyperplastic intima (p < 0.001) as compared with FN-coated DET-decellularized grafts. Moreover, there are no signs of infiltration with inflammatory cells. The present biological, detergent-free, non-proteolytic regimen balances effective decellularization and ECM preservation in cardiovascular grafts, and provides optimized bio-functionality. Additionally, this study implies that the actin-disassembling regimen may be a promising approach for bioengineering of acellular scaffolds from other muscular tissues, as for example myocardium or intestine. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

Nucleolus disassembly and distribution of segregated nucleolar material in prophase of root-tip meristematic cells in Triticum aestivum L.

Directory of Open Access Journals (Sweden)

Wang Jianyue

2015-01-01

Full Text Available This paper presents details of the process of nucleolar disassembly, studied by conventional transmission electron microscopy (TEM in wheat root cells. In early prophase, chromatin condensation and irregular nucleolar morphology are observed, with many small particles appearing around the nucleolus. In middle prophase, the nucleolus radiates outwards; in late prophase, the fine structure of the nucleolus disappears and nucleolar material diffuses away. Using “en bloc” silver-staining to distinguish between nucleoli and chromatin, we observed that the dispersed nucleolar material aggregates around the chromatin, forming a sheath-like perichromosomal structure that coats the chromosomes in late prophase.

Role of a reducing environment in disassembly of the herpesvirus tegument

Energy Technology Data Exchange (ETDEWEB)

Newcomb, William W. [Department of Microbiology Immunology and Cancer Biology, University of Virginia Health System, Box 800734, University of Virginia Health System, 1300 Jefferson Park Ave. Charlottesville, VA 22908 (United States); Jones, Lisa M. [Department of Chemistry, Washington University in St. Louis, St. Louis, MO 63130 (United States); Dee, Alexander [Department of Molecular, Microbial and Structural Biology, University of Connecticut Health Center, Farmington, CT 06030 (United States); Chaudhry, Farid [Department of Microbiology Immunology and Cancer Biology, University of Virginia Health System, Box 800734, University of Virginia Health System, 1300 Jefferson Park Ave. Charlottesville, VA 22908 (United States); Brown, Jay C., E-mail: JCB2G@VIRGINIA.EDU [Department of Microbiology Immunology and Cancer Biology, University of Virginia Health System, Box 800734, University of Virginia Health System, 1300 Jefferson Park Ave. Charlottesville, VA 22908 (United States)

2012-09-15

Initiation of infection by herpes family viruses involves a step in which most of the virus tegument becomes detached from the capsid. Detachment takes place in the host cell cytosol near the virus entry site and it is followed by dispersal of tegument proteins and disappearance of the tegument as a distinct entity. Here we describe the results of experiments designed to test the idea that the reducing environment of the cytosol may contribute to tegument detachment and disassembly. Non-ionic detergent was used to remove the membrane of purified herpes simplex virus under control and reducing conditions. The effects on the tegument were then examined by SDS-PAGE and electron microscopy. Protein analysis demonstrated that most major tegument proteins were removed under both oxidizing and reducing conditions except for UL49 which required a reducing environment. It is proposed therefore that the reducing conditions in the cytosol are involved in removal of UL49 protein. Electron microscopic analysis revealed that capsids produced under oxidizing conditions contained a coating of protein that was absent in reduced virions and which correlated uniquely with the presence of UL49. This capsid-associated layer is suggested to be the location of UL49 in the extracted virion.

Advance on the technology of assembly and disassembly of a head frame with four legs and the machine-assembled head frame

Energy Technology Data Exchange (ETDEWEB)

Zhou Youzong; Cao Baozhen [Ministry of Coal Industry (China). Geological Exploration Machinery Factory

1996-12-31

According to the meditation of assembling headframes from upper to lower instead of that from lower to upper, the authors created successfully a new type of machine for assembling and disassembling headframes as well as a type of machine-assembled headframe. The new type of headframe not only has the merits of old type of headframe with four legs, but also can keep people away from dangers of working in high space and save the workers much labour. The new technology has good effect on raising productive efficiency. 2 figs.

Analysis of the stress-deformed condition of the disassembly parabolic antenna

Science.gov (United States)

Odinets, M. N.; Kaygorodtseva, N. V.; Krysova, I. V.

2018-01-01

Active development of satellite communications and computer-aided design systems raises the problem of designing parabolic antennas on a new round of development. The aim of the work was to investigate the influence of the design of the mirror of a parabolic antenna on its endurance under wind load. The research task was an automated analysis of the stress-deformed condition of various designs of computer models of a paraboloid mirror (segmented or holistic) at modeling the exploitation conditions. The peculiarity of the research was that the assembly model of the antenna’s mirror was subjected to rigid connections on the contacting surfaces of the segments and only then the finite element grid was generated. The analysis showed the advantage of the design of the demountable antenna, which consists of cyclic segments, in front of the construction of the holistic antenna. Calculation of the stress-deformed condition of the antennas allows us to conclude that dividing the design of the antenna’s mirror on parabolic and cyclic segments increases it strength and rigidity. In the future, this can be used to minimize the mass of antenna and the dimensions of the disassembled antenna. The presented way of modeling a mirror of a parabolic antenna using to the method of the finite-element analysis can be used in the production of antennas.

Nucleolus disassembly in mitosis and apoptosis: dynamic redistribution of phosphorylated-c-Myc, fibrillarin and Ki-67

Directory of Open Access Journals (Sweden)

C Soldani

2009-06-01

Full Text Available The nucleolus may undergo disassembly either reversibly during mitosis, or irreversibly in apoptosis, thus allowing the redistribution of the nucleolar proteins.We investigated here by immunocytochemistry the fate of three representative proteins, namely phosphorylated c-Myc, fibrillarin and Ki-67, and found that they behave independently in both processes: they relocate in distinct compartments during mitosis, whereas during apoptosis they may either be cleaved (Ki-67 or be extruded into the cytoplasm with a different kinetics and following an ordered, non chaotic program. The separation of these nucleolar proteins which occurs in early apoptotic nuclei continues also in the cytoplasm, and culminates in the final formation of apoptotic blebs containing different nucleolar proteins: this evidence confirms that the apoptotic bodies may be variable in size, content and surface reactivity, and include heterogeneous aggregates of nuclear proteins and/or nucleic acids.

Low enrichment fuel conversion for Iowa State University

International Nuclear Information System (INIS)

Rohach, A.F.; Hendrickson, R.A.

1991-08-01

Work during the reported period was centered primarily in preparation for receiving the LEU fuel and the shipping of the HEU fuel. This included development of procedures and tools for the disassembly process. During the period we held many practice sessions applying these tools and practices to a dummy fuel assembly. The LEU fuel was received on April 10, 1991 and the reactor was shut down on May 3, 1991 for refueling. The twelve HEU fuel assemblies in the UTR-10 reactor core were removed and disassembled during the week of May 6--9, 1991. The disassembly process went smoothly with only a few minor problems. Also during this reporting period several experimental measurements and preventative maintenance tasks were accomplished. Finally procedures and practices have been developed for the new LEU fuel loading and critical experiments which are to be completed during the late summer of 1991

Low enrichment fuel conversion for Iowa State University

International Nuclear Information System (INIS)

Rohach, A.F.; Hendrickson, R.A.

1990-08-01

Work during the reported period was centered primarily in preparation for receiving the LEU fuel and the shipping of the HEU fuel. The LEU fuel has not been received. The HEU fuel assemblies for the UTR-10 reactor will not fit into any current research reactor shipping containers; therefore, the fuel assemblies must be disassembled and the fuel shipped as fuel plates. Procedures and practices have been developed so that the fuel assemblies will be disassembled in a shielded environment

The pedagogical value of Disassemble/Analyze/Assemble (DAA) activities: Assessing the potential for motivation and transfer

Science.gov (United States)

Dalrymple, Odesma Onika

Undergraduate engineering institutions are currently seeking to improve recruiting practices and to retain engineering majors particularly by addressing what many studies document as a major challenge of poor instruction. There is an undisputed need for instructional practices that motivate students in addition to facilitating the transfer of learning beyond the classroom. Reverse engineering and product dissection, more broadly termed Disassemble/Analyze/Assemble (DAA) activities, have shown potential to address these concerns, based on the reviews of students and professors alike. DAA activities involve the systematic deconstruction of an artifact, the subsequent analysis and possible reconstruction of its components for the purpose of understanding the embodied fundamental concepts, design principles and developmental processes. These activities have been part of regular industry practice for some time; however, the systematic analysis of their benefits for learning and instruction is a relatively recent phenomenon. A number of studies have provided highly descriptive accounts of curricula and possible outcomes of DAA activities; but, relatively few have compared participants doing DAA activities to a control group doing more traditional activities. In this respect, two quasi-experiments were conducted as part of a first-year engineering laboratory, and it was hypothesized that students who engaged in the DAA activity would be more motivated and would demonstrate higher frequencies of transfer than the control. A DAA activity that required students to disassemble a single-use camera and analyze its components to discover how it works was compared to a step-by-step laboratory activity in the first experiment and a lecture method of instruction in the second experiment. In both experiments, over forty percent of the students that engaged in the DAA activity demonstrated the ability to transfer the knowledge gained about the functions of the camera's components and

Rough order of magnitude cost estimate for immobilization of 50 MT of plutonium sharing existing facilities at Hanford with pit disassembly and conversion facility: alternative 11

International Nuclear Information System (INIS)

DiSabatino, A.

1998-01-01

The purpose of this Cost Estimate Report is to identify preliminary capital and operating costs for a facility to immobilize 50 metric tons (nominal) of plutonium as a ceramic in an existing facility at Hanford, the Fuels and Materials Examination Facility (FMEF). The Pit Disassembly and Conversion Facility (PDCF), which is being costed in a separate report by LANL, will also be located in the FMEF in this co-location option

Selenide isotope generator for the Galileo mission. GDS disassembly report

International Nuclear Information System (INIS)

1978-11-01

The GDS-1 was disassembled to determine the cause for the rapid degradation of the output power. Unfortunately, it was not possible to relate the observations to direct causes for the degradation. However, some positive statements can be made which have an impact on the flight program. First, the outgassing and gas management techniques were shown to be adequate to maintain clean conditions within the generator. Second, the non-modular components within the generator including the receptacles on the housing were not affected by the thermal environment during operation of GDS-1. Third, a significant amount of sublimation of the P-legs has occurred during the relatively short life of 2000 + hours as shown by the bullet nosing of the legs and deposits on the cold end hardware. The fact that the generator atmosphere was not 100% xenon may have some bearing on this observation but the statement is still accurate. Fourth, all exposed N-legs display cracks and/or chips. Fifth, a great deal of misalignment of both N and P-legs was seen both visually and with radiographs. Although no definite conclusions can be made concerning the cause for the rapid degradation of performance, several of the observed conditions within the module could possibly contribute to that fact. They are: cracks in N-legs (increased resistance); deposits on edges of BeO discs (shorting of thermoelectric circuit); and bullet nosing of P-legs (increased resistance). It remains to be shown if any of these effects or the follower hangup described earlier contributed to the poor performance of GDS-1 or if another effect as yet unknown was the important factor

Isotope identification as a part of the decommissioning of San Diego State University's Texas Nuclear neutron generator

International Nuclear Information System (INIS)

Taylor, D.

1997-07-01

The Department of Physics at San Diego State University has maintained a Neutron Generator facility in room P-32C since the mid 1960's. This facility has provided students and faculty with a resource for the study of neutron interactions with matter, such as activation analysis, flux determinations, cross section determinations and shielding studies. The model 9500 was built by Texas Nuclear Research in the early 1960's, and could be used for either photon or neutron generation, depending on the source ions introduced into the accelerator's plasma bottle and the target material. In February of 1988, the Texas Nuclear Research neutron generator was replaced by a unit manufactured by Kaman Sciences Corporation. The Texas Nuclear unit was then removed and stored for later disassembly and disposal. In the summer of 1993, the neutron generator was disassembled into three large sections consisting of the titanium-tritide target, the oil diffusion pump and the corona shield/accelerator tube assembly. The target was packaged and stored in room P-33A and the other 2 assemblies were wrapped in plastic for storage. In June of 1995 the neutron generator was further disassembled to enable storage in 55 gallon drums and thoroughly surveyed for loose surface contamination. Openings on the disassembled hardware components were closed off using either duct tape or bolted stainless steel flanges to prevent the possible spread of contamination. Significant levels of removable surface contamination could be found on system internal and some external surfaces, up to five hundred thousand disintegrations per minute. Initial analysis of the removable contamination using aluminum absorbers and a Geiger-Meuller tube indicated beta particle or possibly photon emitters with an energy of approximately 180 keV. This apparent radiation energy conflicted with what one would be expected to find, given knowledge of the source material and the possible neutron activated products that would be

Disassembly of Bacterial Biofilms by the Self-Assembled Glycolipids Derived from Renewable Resources.

Science.gov (United States)

Prasad, Yadavali Siva; Miryala, Sandeep; Lalitha, Krishnamoorthy; Ranjitha, K; Barbhaiwala, Shehnaz; Sridharan, Vellaisamy; Maheswari, C Uma; Srinandan, C S; Nagarajan, Subbiah

2017-11-22

More than 80% of chronic infections of bacteria are caused by biofilms. It is also a long-term survival strategy of the pathogens in a nonhost environment. Several amphiphilic molecules have been used in the past to potentially disrupt biofilms; however, the involvement of multistep synthesis, complicated purification and poor yield still remains a major problem. Herein, we report a facile synthesis of glycolipid based surfactant from renewable feedstocks in good yield. The nature of carbohydrate unit present in glycolipid influence the ring chain tautomerism, which resulted in the existence of either cyclic structure or both cyclic and acyclic structures. Interestingly, these glycolipids self-assemble into gel in highly hydrophobic solvents and vegetable oils, and displayed foam formation in water. The potential application of these self-assembled glycolipids to disrupt preformed biofilm was examined against various pathogens. It was observed that glycolipid 6a disrupts Staphylococcus aureus and Listeria monocytogenes biofilm, while the compound 6c was effective in disassembling uropathogenic E. coli and Salmonella enterica Typhimurium biofilms. Altogether, the supramolecular self-assembled materials, either as gel or as surfactant solution could be potentially used for surface cleansing in hospital environments or the food processing industries to effectively reduce pathogenic biofilms.

Substantiation of the admissable concentration of radionuclides in the utilization of concrete from disassembled reactors

International Nuclear Information System (INIS)

Engovatov, I.A.; Mashkovich, V.P.; Morev, M.N.

1995-01-01

The complete or partial disassembly of the buildings and systems of a modern nuclear power plant results in the formation of hundreds of thousands of tons of wastes. More than 90% of this mass consists of reinforced concrete. Only a small fraction of these materials is contaminated and/or activated up to high level and must be treated as radioactive wastes that must be buried. For this reason, it is helpful to consider a variant of recycling of some of the wastes and secondary utilization of these wastes in different industrial production processes. In this paper, we analyze the concrete that is freed when a nuclear power plant is decommissioned, and in particular, we examine three scenarios: (1) stockpiling and long-term storage of concrete at an industrial site, (2) highway construction, and (3) industrial building construction. Admissable radionuclide concentrations of several isotopes are tabulated for each scenario, and the results provide the basic information for the development of standards for the utilization of the concrete wastes produced during the decommissioning of nuclear power plants

Protein dynamics of human RPA and RAD51 on ssDNA during assembly and disassembly of the RAD51 filament.

Science.gov (United States)

Ma, Chu Jian; Gibb, Bryan; Kwon, YoungHo; Sung, Patrick; Greene, Eric C

2017-01-25

Homologous recombination (HR) is a crucial pathway for double-stranded DNA break (DSB) repair. During the early stages of HR, the newly generated DSB ends are processed to yield long single-stranded DNA (ssDNA) overhangs, which are quickly bound by replication protein A (RPA). RPA is then replaced by the DNA recombinase Rad51, which forms extended helical filaments on the ssDNA. The resulting nucleoprotein filament, known as the presynaptic complex, is responsible for pairing the ssDNA with homologous double-stranded DNA (dsDNA), which serves as the template to guide DSB repair. Here, we use single-molecule imaging to visualize the interplay between human RPA (hRPA) and human RAD51 during presynaptic complex assembly and disassembly. We demonstrate that ssDNA-bound hRPA can undergo facilitated exchange, enabling hRPA to undergo rapid exchange between free and ssDNA-bound states only when free hRPA is present in solution. Our results also indicate that the presence of free hRPA inhibits RAD51 filament nucleation, but has a lesser impact upon filament elongation. This finding suggests that hRPA exerts important regulatory influence over RAD51 and may in turn affect the properties of the assembled RAD51 filament. These experiments provide an important basis for further investigations into the regulation of human presynaptic complex assembly. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

In situ solid-state NMR and XRD studies of the ADOR process and the unusual structure of zeolite IPC-6

Science.gov (United States)

Morris, Samuel A.; Bignami, Giulia P. M.; Tian, Yuyang; Navarro, Marta; Firth, Daniel S.; Čejka, Jiří; Wheatley, Paul S.; Dawson, Daniel M.; Slawinski, Wojciech A.; Wragg, David S.; Morris, Russell E.; Ashbrook, Sharon E.

2017-10-01

The assembly-disassembly-organization-reassembly (ADOR) mechanism is a recent method for preparing inorganic framework materials and, in particular, zeolites. This flexible approach has enabled the synthesis of isoreticular families of zeolites with unprecedented continuous control over porosity, and the design and preparation of materials that would have been difficult—or even impossible—to obtain using traditional hydrothermal techniques. Applying the ADOR process to a parent zeolite with the UTL framework topology, for example, has led to six previously unknown zeolites (named IPC-n, where n = 2, 4, 6, 7, 9 and 10). To realize the full potential of the ADOR method, however, a further understanding of the complex mechanism at play is needed. Here, we probe the disassembly, organization and reassembly steps of the ADOR process through a combination of in situ solid-state NMR spectroscopy and powder X-ray diffraction experiments. We further use the insight gained to explain the formation of the unusual structure of zeolite IPC-6.

New findings on the onset of thermal disassembly in spallation reactions

International Nuclear Information System (INIS)

Napolitani, P.

2004-09-01

Thermal multifragmentation is the process of multi body disassembly of a hot nucleus when the excitation is almost purely thermal i.e. dynamical effects like compression (characteristic of ion-ion collisions at Fermi energy) are negligible. Suited reactions are proton induced collision or ion-ion abrasion at relativistic incident energy. Thus we measured four systems at FRS (Fragment separator, GSI, Darmstadt) in inverse kinematics: Fe 56 +p, Fe 56 +Ti(nat), Xe 136 +p, Xe 136 +Ti(nat) a 1 A*GeV. The inverse kinematics allows to observe all particles without any threshold in energy. This is a great advantage compared to experiments in direct kinematics, because only in inverse kinematics it is possible to obtain complete velocity spectra (without a hole for low velocities) for fully identified isotopes. The complex shape of the velocity spectra allows to identify the different deexcitation channels and it clearly shows the transition from a chaotic-dominated process (Gaussian cloud in velocity space) to a direct Coulomb- (or eventually expansion-) dominated process (shell of a sphere in velocity space). Different possible descriptions of the reaction process are discussed, based either on asymmetric fission or multifragmentation. The resulting physical picture is especially interesting for the Fe 56 +p, and Xe 136 +p systems: proton induced collisions could result in the split of the system in two or more fragments due to a fast break-up process. In this case, the configuration of the break-up partition is very asymmetric. The discussion will be extended to other characteristics, like the restoring of nuclear structure features in the isotopic production and the temperature dependence of the isotopic composition of the residues. (author)

Sodium removal disassembly and examination of the Fermi secondary sodium pump

International Nuclear Information System (INIS)

Maffei, H.P.; Funk, C.W.; Ballif, J.L.

1974-01-01

The Fermi secondary pump is a centrifugal single stage design. The pump had been operated more than 42,000 hours between 450 and 800 0 F. Sodium was drained from the pump in 1973 and the system was back filled with carbon dioxide. The pump was fabricated for 2.25 Cr-1 Mo Croloy steel. Prior to cleaning the pump was inerted and heated with 150 0 F nitrogen using the pump casing as the containment vessel. The water-vapor-nitrogen process was used in three increasing stages of water concentration. The hydrogen concentration in the discharge line was followed as an indicator of the sodium-water reaction rate. Upon completion of the hydrogen evolution, the pump was rinsed several times with hot water. Six pounds of sodium were removed from the pump during a process cycle of 79 hours including rinsing. The maximum pump temperature recorded was 175 0 F with no variation exceeding 10 0 F. The hydrogen concentration in the effluent provided a very satisfactory index for control of the reaction by adjustment of the water-vapor concentration feed to the system. Rinsing effectiveness was limited by a pool of water in the volute that was not drainable with the available system hook up. Sodium and its compounds were removed from all internal surfaces that could be observed by the first stage of disassembly. All such surfaces were coated with a black deposit. Areas above the sodium liquid level were coated with a vermillion colored oxide. Sodium was found on the (1) threads of the impeller nut lock screw, (2) impeller nut-tapered shaft interface, and (3) vapor deposited sodium was found in the oil seal

Disassembly of Faceted Macrosteps in the Step Droplet Zone in Non-Equilibrium Steady State

Directory of Open Access Journals (Sweden)

Noriko Akutsu

2017-02-01

Full Text Available A Wulff figure—the polar graph of the surface tension of a crystal—with a discontinuity was calculated by applying the density matrix renormalization group method to the p-RSOS model, a restricted solid-on-solid model with a point-contact-type step–step attraction. In the step droplet zone in this model, the surface tension is discontinuous around the (111 surface and continuous around the (001 surface. The vicinal surface of 4H-SiC crystal in a Si–Cr–C solution is thought to be in the step droplet zone. The dependence of the vicinal surface growth rate and the macrostep size 〈 n 〉 on the driving force Δ μ for a typical state in the step droplet zone in non-equilibrium steady state was calculated using the Monte Carlo method. In contrast to the known step bunching phenomenon, the size of the macrostep was found to decrease with increasing driving force. The detachment of elementary steps from a macrostep was investigated, and it was found that 〈 n 〉 satisfies a scaling function. Moreover, kinetic roughening was observed for | Δ μ | > Δ μ R , where Δ μ R is the crossover driving force above which the macrostep disappears.

Low enrichment fuel conversion for Iowa State University. Final report

International Nuclear Information System (INIS)

Bullen, D.B.; Wendt, S.E.

1996-01-01

The UTR-10 research and teaching reactor at Iowa State University (ISU) has been converted from high-enriched fuel (HEU) to low- enriched fuel (LEU) under Grant No. DE-FG702-87ER75360 from the Department of Energy (DOE). The original contract period was August 1, 1987 to July 31, 1989. The contract was extended to February 28, 1991 without additional funding. Because of delays in receiving the LEU fuel and the requirement for disassembly of the HEU assemblies, the contract was renewed first through May 31, 1992, then through May 31, 1993 with additional funding, and then again through July 31, 1994 with no additional funding. In mid-August the BMI cask was delivered to Iowa State. Preparations are underway to ship the HEU fuel when NRC license amendments for the cask are approved

Development of an advanced, continuous mild-gasification process for the production of coproducts. Report for Task 4.8, Decontamination and disassembly of the mild-gasification and char-to-carbon PRUs and disposal of products from testing

Energy Technology Data Exchange (ETDEWEB)

Merriam, N.W. [Western Research Inst., Laramie, WY (United States); Jha, Mahesh C. [AMAX Research and Development Center, Golden, CO (United States)

1991-11-01

This report contains descriptions of mild-gasification and char-to-carbon process research units (PRUS) used by WRI and AMAX R&D Center to conduct tests under contract AC21-87MC24268. Descriptions of materials produced during those tests are also contained herein. Western Research Institute proposes to dispose of remaining fines and dried coal by combustion and remaining coal liquids by incineration during mid-1992. The mild-gasification PRU will be used for additional tests until 1993, at which time WRI proposes to decontaminate and disassemble the PRU. AMAX R&D Center intends to return the spent char, any remaining feed char, and unusable product carbon to the Eagle Butte Mine near Gillette, Wyoming, from where the coal originally came. The solid products will be added to the mine`s coal product stream. Coal liquids collected from condensers will be concentrated and sent to a local oil and solvent recycling company where the liquids will be burned as fuel. The char-to-carbon PRU will be operated periodically until 1993 when the plant will be decontaminated and disassembled.

The rem mutations in the ATP-binding groove of the Rad3/XPD helicase lead to Xeroderma pigmentosum-Cockayne syndrome-like phenotypes.

Science.gov (United States)

Herrera-Moyano, Emilia; Moriel-Carretero, María; Montelone, Beth A; Aguilera, Andrés

2014-12-01

The eukaryotic TFIIH complex is involved in Nucleotide Excision Repair and transcription initiation. We analyzed three yeast mutations of the Rad3/XPD helicase of TFIIH known as rem (recombination and mutation phenotypes). We found that, in these mutants, incomplete NER reactions lead to replication fork breaking and the subsequent engagement of the homologous recombination machinery to restore them. Nevertheless, the penetrance varies among mutants, giving rise to a phenotype gradient. Interestingly, the mutations analyzed reside at the ATP-binding groove of Rad3 and in vivo experiments reveal a gain of DNA affinity upon damage of the mutant Rad3 proteins. Since mutations at the ATP-binding groove of XPD in humans are present in the Xeroderma pigmentosum-Cockayne Syndrome (XP-CS), we recreated rem mutations in human cells, and found that these are XP-CS-like. We propose that the balance between the loss of helicase activity and the gain of DNA affinity controls the capacity of TFIIH to open DNA during NER, and its persistence at both DNA lesions and promoters. This conditions NER efficiency and transcription resumption after damage, which in human cells would explain the XP-CS phenotype, opening new perspectives to understand the molecular basis of the role of XPD in human disease.

Improvement and verification of fast reactor safety analysis techniques

International Nuclear Information System (INIS)

Jackson, J.F.

1975-01-01

An initial analysis of the KIWI-TNT experiment using the VENUS-II disassembly code has been completed. The calculated fission energy release agreed with the experimental value to within about 3 percent. An initial model for analyzing the SNAPTRAN-2 core disassembly experiment was also developed along with an appropriate equation-of-state. The first phase of the VENUS-II/PAD comparison study was completed through the issuing of a preliminary report describing the results. A new technique to calculate a P-V-work curve as a function of the degree of core expansion following a disassembly excursion has been developed. The technique provides results that are consistent with the ANL oxide-fuel equation-of-state in VENUS-II. Evaluation and check-out of this new model are currently in progress

TFG facilitates outer coat disassembly on COPII transport carriers to promote tethering and fusion with ER-Golgi intermediate compartments.

Science.gov (United States)

Hanna, Michael G; Block, Samuel; Frankel, E B; Hou, Feng; Johnson, Adam; Yuan, Lin; Knight, Gavin; Moresco, James J; Yates, John R; Ashton, Randolph; Schekman, Randy; Tong, Yufeng; Audhya, Anjon

2017-09-12

The conserved coat protein complex II (COPII) mediates the initial steps of secretory protein trafficking by assembling onto subdomains of the endoplasmic reticulum (ER) in two layers to generate cargo-laden transport carriers that ultimately fuse with an adjacent ER-Golgi intermediate compartment (ERGIC). Here, we demonstrate that Trk-fused gene (TFG) binds directly to the inner layer of the COPII coat. Specifically, the TFG C terminus interacts with Sec23 through a shared interface with the outer COPII coat and the cargo receptor Tango1/cTAGE5. Our findings indicate that TFG binding to Sec23 outcompetes these other associations in a concentration-dependent manner and ultimately promotes outer coat dissociation. Additionally, we demonstrate that TFG tethers vesicles harboring the inner COPII coat, which contributes to their clustering between the ER and ERGIC in cells. Together, our studies define a mechanism by which COPII transport carriers are retained locally at the ER/ERGIC interface after outer coat disassembly, which is a prerequisite for fusion with ERGIC membranes.

HUWE1 Ubiquitylates and Degrades the RAC Activator TIAM1 Promoting Cell-Cell Adhesion Disassembly, Migration, and Invasion

Directory of Open Access Journals (Sweden)

Lynsey Vaughan

2015-01-01

Full Text Available The E3 ubiquitin ligase HUWE1, deregulated in carcinoma, has been implicated in tumor formation. Here, we uncover a role for HUWE1 in cell migration and invasion through degrading the RAC activator TIAM1, implying an additional function in malignant progression. In MDCKII cells in response to HGF, HUWE1 catalyzes TIAM1 ubiquitylation and degradation predominantly at cell-cell adhesions, facilitating junction disassembly, migration, and invasion. Depleting HUWE1 or mutating the TIAM1 ubiquitylation site prevents TIAM1 degradation, antagonizing scattering, and invasion. Moreover, simultaneous depletion of TIAM1 restores migration and invasion in HUWE1-depleted cells. Significantly, we show that HUWE1 stimulates human lung cancer cell invasion through regulating TIAM1 stability. Finally, we demonstrate that HUWE1 and TIAM1 protein levels are inversely correlated in human lung carcinomas. Thus, we elucidate a critical role for HUWE1 in regulating epithelial cell-cell adhesion and provide additional evidence that ubiquitylation contributes to spatiotemporal control of RAC.

Mediator independently orchestrates multiple steps of preinitiation complex assembly in vivo.

Science.gov (United States)

Eyboulet, Fanny; Wydau-Dematteis, Sandra; Eychenne, Thomas; Alibert, Olivier; Neil, Helen; Boschiero, Claire; Nevers, Marie-Claire; Volland, Hervé; Cornu, David; Redeker, Virginie; Werner, Michel; Soutourina, Julie

2015-10-30

Mediator is a large multiprotein complex conserved in all eukaryotes, which has a crucial coregulator function in transcription by RNA polymerase II (Pol II). However, the molecular mechanisms of its action in vivo remain to be understood. Med17 is an essential and central component of the Mediator head module. In this work, we utilised our large collection of conditional temperature-sensitive med17 mutants to investigate Mediator's role in coordinating preinitiation complex (PIC) formation in vivo at the genome level after a transfer to a non-permissive temperature for 45 minutes. The effect of a yeast mutation proposed to be equivalent to the human Med17-L371P responsible for infantile cerebral atrophy was also analyzed. The ChIP-seq results demonstrate that med17 mutations differentially affected the global presence of several PIC components including Mediator, TBP, TFIIH modules and Pol II. Our data show that Mediator stabilizes TFIIK kinase and TFIIH core modules independently, suggesting that the recruitment or the stability of TFIIH modules is regulated independently on yeast genome. We demonstrate that Mediator selectively contributes to TBP recruitment or stabilization to chromatin. This study provides an extensive genome-wide view of Mediator's role in PIC formation, suggesting that Mediator coordinates multiple steps of a PIC assembly pathway. © The Author(s) 2015. Published by Oxford University Press on behalf of Nucleic Acids Research.

Consequence analysis of core damage states following severe accidents for the CANDU reactor design

International Nuclear Information System (INIS)

Wahba, N.N.; Kim, Y.T.; Lie, S.G.

1997-01-01

The analytical methodology used to evaluate severe accident sequences is described. The relevant thermal-mechanical phenomena and the mathematical approach used in calculating the timing of the accident progression and source term estimate are summarized. The postulated sever accidents analyzed, in general, mainly differ in the timing to reach and progress through each defined c ore damage state . This paper presents the methodology and results of the timing and steam discharge calculations as well as source term estimate out of containment for accident sequences classified as potentially leading to core disassembly following a small break loss-of-coolant accident (LOCA) scenario as a specific example. (author)

Streamlined Approach for Environmental Restoration Plan for Corrective Action Unit 113: Reactor Maintenance, Assembly, and Disassembly Building Nevada Test Site, Nevada

Energy Technology Data Exchange (ETDEWEB)

J. L. Smith

2001-01-01

This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the action necessary for the closure in place of Corrective Action Unit (CAU) 113 Area 25 Reactor Maintenance, Assembly, and Disassembly Facility (R-MAD). CAU 113 is currently listed in Appendix III of the Federal Facility Agreement and Consent Order (FFACO) (NDEP, 1996). The CAU is located in Area 25 of the Nevada Test Site (NTS) and consists of Corrective Action Site (CAS) 25-04-01, R-MAD Facility (Figures 1-2). This plan provides the methodology for closure in place of CAU 113. The site contains radiologically impacted and hazardous material. Based on preassessment field work, there is sufficient process knowledge to close in place CAU 113 using the SAFER process. At a future date when funding becomes available, the R-MAD Building (25-3110) will be demolished and inaccessible radiologic waste will be properly disposed in the Area 3 Radiological Waste Management Site (RWMS).

Streamlined Approach for Environmental Restoration Plan for Corrective Action Unit 113: Reactor Maintenance, Assembly, and Disassembly Building Nevada Test Site, Nevada

International Nuclear Information System (INIS)

Smith, J. L.

2001-01-01

This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the action necessary for the closure in place of Corrective Action Unit (CAU) 113 Area 25 Reactor Maintenance, Assembly, and Disassembly Facility (R-MAD). CAU 113 is currently listed in Appendix III of the Federal Facility Agreement and Consent Order (FFACO) (NDEP, 1996). The CAU is located in Area 25 of the Nevada Test Site (NTS) and consists of Corrective Action Site (CAS) 25-04-01, R-MAD Facility (Figures 1-2). This plan provides the methodology for closure in place of CAU 113. The site contains radiologically impacted and hazardous material. Based on preassessment field work, there is sufficient process knowledge to close in place CAU 113 using the SAFER process. At a future date when funding becomes available, the R-MAD Building (25-3110) will be demolished and inaccessible radiologic waste will be properly disposed in the Area 3 Radiological Waste Management Site (RWMS)

Wood cell-wall structure requires local 2D-microtubule disassembly by a novel plasma membrane-anchored protein.

Science.gov (United States)

Oda, Yoshihisa; Iida, Yuki; Kondo, Yuki; Fukuda, Hiroo

2010-07-13

Plant cells have evolved cortical microtubules, in a two-dimensional space beneath the plasma membrane, that regulate patterning of cellulose deposition. Although recent studies have revealed that several microtubule-associated proteins facilitate self-organization of transverse cortical microtubules, it is still unknown how diverse patterns of cortical microtubules are organized in different xylem cells, which are the major components of wood. Using our newly established in vitro xylem cell differentiation system, we found that a novel microtubule end-tracking protein, microtubule depletion domain 1 (MIDD1), was anchored to distinct plasma membrane domains and promoted local microtubule disassembly, resulting in pits on xylem cell walls. The introduction of RNA interference for MIDD1 resulted in the failure of local microtubule depletion and the formation of secondary walls without pits. Conversely, the overexpression of MIDD1 reduced microtubule density. MIDD1 has two coiled-coil domains for the binding to microtubules and for the anchorage to plasma membrane domains, respectively. Combination of the two coils caused end tracking of microtubules during shrinkage and suppressed their rescue events. Our results indicate that MIDD1 integrates spatial information in the plasma membrane with cortical microtubule dynamics for determining xylem cell wall pattern. Copyright 2010 Elsevier Ltd. All rights reserved.

Disassembly of actin structures by nanosecond pulsed electric field is a downstream effect of cell swelling.

Science.gov (United States)

Pakhomov, Andrei G; Xiao, Shu; Pakhomova, Olga N; Semenov, Iurii; Kuipers, Marjorie A; Ibey, Bennett L

2014-12-01

Disruption of the actin cytoskeleton structures was reported as one of the characteristic effects of nanosecond-duration pulsed electric field (nsPEF) in both mammalian and plant cells. We utilized CHO cells that expressed the monomeric fluorescent protein (mApple) tagged to actin to test if nsPEF modifies the cell actin directly or as a consequence of cell membrane permeabilization. A train of four 600-ns pulses at 19.2 kV/cm (2 Hz) caused immediate cell membrane poration manifested by YO-PRO-1 dye uptake, gradual cell rounding and swelling. Concurrently, bright actin features were replaced by dimmer and uniform fluorescence of diffuse actin. To block the nsPEF-induced swelling, the bath buffer was isoosmotically supplemented with an electropore-impermeable solute (sucrose). A similar addition of a smaller, electropore-permeable solute (adonitol) served as a control. We demonstrated that sucrose efficiently blocked disassembly of actin features by nsPEF, whereas adonitol did not. Sucrose also attenuated bleaching of mApple-tagged actin in nsPEF-treated cells (as integrated over the cell volume), although did not fully prevent it. We conclude that disintegration of the actin cytoskeleton was a result of cell swelling, which, in turn, was caused by cell permeabilization by nsPEF and transmembrane diffusion of solutes which led to the osmotic imbalance. Copyright © 2014 Elsevier B.V. All rights reserved.

Disassembly of microtubules and inhibition of neurite outgrowth, neuroblastoma cell proliferation, and MAP kinase tyrosine dephosphorylation by dibenzyl trisulphide.

Science.gov (United States)

Rösner, H; Williams, L A; Jung, A; Kraus, W

2001-08-22

Dibenzyl trisulphide (DTS), a main lipophilic compound in Petiveria alliacea L. (Phytolaccaceae), was identified as one of the active immunomodulatory compounds in extracts of the plant. To learn more about its biological activities and molecular mechanisms, we conducted one-dimensional NMR interaction studies with bovine serum albumin (BSA) and tested DTS and related compounds in two well-established neuronal cell-and-tissue culture systems. We found that DTS preferentially binds to an aromatic region of BSA which is rich in tyrosyl residues. In SH-SY5Y neuroblastoma cells, DTS attenuates the dephosphorylation of tyrosyl residues of MAP kinase (erk1/erk2). In the same neuroblastoma cell line and in Wistar 38 human lung fibroblasts, DTS causes a reversible disassembly of microtubules, but it did not affect actin dynamics. Probably due to the disruption of the microtubule dynamics, DTS also inhibits neuroblastoma cell proliferation and neurite outgrowth from spinal cord explants. Related dibenzyl compounds with none, one, or two sulphur atoms were found to be significantly less effective. These data confirmed that the natural compound DTS has a diverse spectrum of biological properties, including cytostatic and neurotoxic actions in addition to immunomodulatory activities.

A ΩXaV motif in the Rift Valley fever virus NSs protein is essential for degrading p62, forming nuclear filaments and virulence.

Science.gov (United States)

Cyr, Normand; de la Fuente, Cynthia; Lecoq, Lauriane; Guendel, Irene; Chabot, Philippe R; Kehn-Hall, Kylene; Omichinski, James G

2015-05-12

Rift Valley fever virus (RVFV) is a single-stranded RNA virus capable of inducing fatal hemorrhagic fever in humans. A key component of RVFV virulence is its ability to form nuclear filaments through interactions between the viral nonstructural protein NSs and the host general transcription factor TFIIH. Here, we identify an interaction between a ΩXaV motif in NSs and the p62 subunit of TFIIH. This motif in NSs is similar to ΩXaV motifs found in nucleotide excision repair (NER) factors and transcription factors known to interact with p62. Structural and biophysical studies demonstrate that NSs binds to p62 in a similar manner as these other factors. Functional studies in RVFV-infected cells show that the ΩXaV motif is required for both nuclear filament formation and degradation of p62. Consistent with the fact that the RVFV can be distinguished from other Bunyaviridae-family viruses due to its ability to form nuclear filaments in infected cells, the motif is absent in the NSs proteins of other Bunyaviridae-family viruses. Taken together, our studies demonstrate that p62 binding to NSs through the ΩXaV motif is essential for degrading p62, forming nuclear filaments and enhancing RVFV virulence. In addition, these results show how the RVFV incorporates a simple motif into the NSs protein that enables it to functionally mimic host cell proteins that bind the p62 subunit of TFIIH.

The yeast protein kinase Sch9 adjusts V-ATPase assembly/disassembly to control pH homeostasis and longevity in response to glucose availability.

Directory of Open Access Journals (Sweden)

Tobias Wilms

2017-06-01

Full Text Available The conserved protein kinase Sch9 is a central player in the nutrient-induced signaling network in yeast, although only few of its direct substrates are known. We now provide evidence that Sch9 controls the vacuolar proton pump (V-ATPase to maintain cellular pH homeostasis and ageing. A synthetic sick phenotype arises when deletion of SCH9 is combined with a dysfunctional V-ATPase, and the lack of Sch9 has a significant impact on cytosolic pH (pHc homeostasis. Sch9 physically interacts with, and influences glucose-dependent assembly/disassembly of the V-ATPase, thereby integrating input from TORC1. Moreover, we show that the role of Sch9 in regulating ageing is tightly connected with V-ATPase activity and vacuolar acidity. As both Sch9 and the V-ATPase are highly conserved in higher eukaryotes, it will be interesting to further clarify their cooperative action on the cellular processes that influence growth and ageing.

Evaluation of nuclear facility decommissioning projects. Three Mile Island Unit 2 reactor defueling and disassembly. Summary status report. Volume 3

International Nuclear Information System (INIS)

Doerge, D.H.; Miller, R.L.; Scotti, K.S.

1986-05-01

This document summarizes information relating to the preparations for defueling the Three Mile Island Unit 2 (TMI-2) reactor and disassembly activities being performed concurrently with decontamination of the facility. Data have been collected from activity reports, reactor containment entry records, and other sources and entered in a computerized data sysem which permits extraction/manipulation of specific data which can be used in planning for recovery from a loss of coolant event similar to that experienced at TMI-2 on March 28, 1979. This report contains summaries of man-hours, manpower, and radiation exposures incurred during the period of April 23, 1979 to April 16, 1985, in the completion of activities related to preparation for reactor defueling. Support activities conducted outside of radiation areas are not included within the scope of this report. Computerized reports included in this document are: A chronological summary listing work performed for the period; and summary reports for each major task undertaken in connection with the specific scope of this report. Presented in chronological order for the referenced time period. Manually-assembled table summaries are included for: Labor and exposures by department; and labor and exposures by major activity

Cisplatin- and UV-damaged DNA lure the basal transcription factor TFIID/TBP.

NARCIS (Netherlands)

P. Vichi; F. Coin (Frédéric); J-P. Renaud (Jean-Paul); W. Vermeulen (Wim); J.H.J. Hoeijmakers (Jan); D. Moras; J-M. Egly (Jean-Marc)

1997-01-01

textabstractA connection between transcription and DNA repair was demonstrated previously through the characterization of TFIIH. Using filter binding as well as in vitro transcription challenge competition assays, we now show that the promoter recognition factor TATA box-binding protein (TBP)/TFIID

Rab5 GTPase controls chromosome alignment through Lamin disassembly and relocation of the NuMA-like protein Mud to the poles during mitosis

Science.gov (United States)

Capalbo, Luisa; D'Avino, Pier Paolo; Archambault, Vincent; Glover, David M.

2011-01-01

The small GTPase Rab5 is a conserved regulator of membrane trafficking; it regulates the formation of early endosomes, their transport along microtubules, and the fusion to the target organelles. Although several members of the endocytic pathway were recently implicated in spindle organization, it is unclear whether Rab5 has any role during mitosis. Here, we describe that Rab5 is required for proper chromosome alignment during Drosophila mitoses. We also found that Rab5 associated in vivo with nuclear Lamin and mushroom body defect (Mud), the Drosophila counterpart of nuclear mitotic apparatus protein (NuMA). Consistent with this finding, Rab5 was required for the disassembly of the nuclear envelope at mitotic entry and the accumulation of Mud at the spindle poles. Furthermore, Mud depletion caused chromosome misalignment defects that resembled the defects of Rab5 RNAi cells, and double-knockdown experiments indicated that the two proteins function in a linear pathway. Our results indicate a role for Rab5 in mitosis and reinforce the emerging view of the contributions made by cell membrane dynamics to spindle function. PMID:21987826

The spatio-temporal organization of DNA-repair: a live cell study

NARCIS (Netherlands)

D. Hoogstraten (Deborah)

2003-01-01

textabstractThe aim of the work outlined in this thesis is to gain more insight into the organization, dynamic properties and differential reaction kinetics of NER factors within living mammalian cell nuclei. To accomplish this, we made use of the green fluorescent protein technology to study TFIIH

Inositol hexakisphosphate kinase-1 mediates assembly/disassembly of the CRL4–signalosome complex to regulate DNA repair and cell death

Science.gov (United States)

Rao, Feng; Xu, Jing; Khan, A. Basit; Gadalla, Moataz M.; Cha, Jiyoung Y.; Xu, Risheng; Tyagi, Richa; Dang, Yongjun; Chakraborty, Anutosh; Snyder, Solomon H.

2014-01-01

Inositol polyphosphates containing an energetic pyrophosphate bond are formed primarily by a family of three inositol hexakisphosphate (IP6) kinases (IP6K1–3). The Cullin-RING ubiquitin ligases (CRLs) regulate diverse biological processes through substrate ubiquitylation. CRL4, comprising the scaffold Cullin 4A/B, the E2-interacting Roc1/2, and the adaptor protein damage-specific DNA-binding protein 1, is activated by DNA damage. Basal CRL4 activity is inhibited by binding to the COP9 signalosome (CSN). UV radiation and other stressors dissociate the complex, leading to E3 ligase activation, but signaling events that trigger signalosome dissociation from CRL4 have been unclear. In the present study, we show that, under basal conditions, IP6K1 forms a ternary complex with CSN and CRL4 in which IP6K1 and CRL4 are inactive. UV dissociates IP6K1 to generate IP7, which then dissociates CSN–CRL4 to activate CRL4. Thus, IP6K1 is a novel CRL4 subunit that transduces UV signals to mediate disassembly of the CRL4–CSN complex, thereby regulating nucleotide excision repair and cell death. PMID:25349427

Sequence Classification: 893428 [

Lifescience Database Archive (English)

Full Text Available e subunit, involved in recruitment of RNA polymerase II to the promoter, activation of TFIIH, and promoter opening; Tfa1p || http://www.ncbi.nlm.nih.gov/protein/6322824 ... ...Non-TMB Non-TMH Non-TMB Non-TMB TMB Non-TMB >gi|6322824|ref|NP_012897.1| TFIIE larg

Final Status Survey Report for Corrective Action Unit 117 - Pluto Disassembly Facility, Building 2201, Nevada National Security Site, Nevada

International Nuclear Information System (INIS)

Gwin, Jeremy; Frenette, Douglas

2010-01-01

This document contains the process knowledge, radiological data and subsequent statistical methodology and analysis to support approval for the radiological release of Corrective Action Unit (CAU) 117 - Pluto Disassembly Facility, Building 2201 located in Area 26 of the Nevada National Security Site (NNSS). Preparations for release of the building began in 2009 and followed the methodology described in the Multi-Agency Radiation Survey and Site Investigation Manual (MARSSIM). MARSSIM is the DOE approved process for release of Real Property (buildings and landmasses) to a set of established criteria or authorized limits. The pre-approved authorized limits for surface contamination values and corresponding assumptions were established by DOE O 5400.5. The release criteria coincide with the acceptance criteria of the U10C landfill permit. The U10C landfill is the proposed location to dispose of the radiologically non-impacted, or ''clean,'' building rubble following demolition. However, other disposition options that include the building and/or waste remaining at the NNSS may be considered providing that the same release limits apply. The Final Status Survey was designed following MARSSIM guidance by reviewing historical documentation and radiological survey data. Following this review a formal radiological characterization survey was performed in two phases. The characterization revealed multiple areas of residual radioactivity above the release criteria. These locations were remediated (decontaminated) and then the surface activity was verified to be less than the release criteria. Once remediation efforts had been successfully completed, a Final Status Survey Plan (10-015, ''Final Status Survey Plan for Corrective Action Unit 117 - Pluto Disassembly Facility, Building 2201'') was developed and implemented to complete the final step in the MARSSIM process, the Final Status Survey. The Final Status Survey Plan consisted of categorizing each individual room into one

Temporal sealing material of tritium-contaminated stainless steel

International Nuclear Information System (INIS)

Wen Wei; Dan Guiping; Zhang Dong; Qiu Yongmei; Zhang Li

2010-01-01

Tritium can be released from the exterior of tritium-contaminated stainless steel by slight stirring while decontaminating and disassembling. In order to avoid secondary tritium contamination to environment and operators, it is necessary to cover with an effective coating to tritium on the exterior of tritium-contaminated stainless steel and fill an effective substance to tritium inside. The results of tritium sealed experiments show that sealing efficiency of neutral silicone rubber is more than 85% for condition of static state and more than 99% for foam concrete condition of dynamic state. Neutral silicone rubber and foam concrete which have finer sealing efficiency can be used as temporal sealed material for the decontamination and disassembly of tritium-contaminated stainless steel. (authors)

XPD Helicase Structures and Activities: Insights into the Cancer and Aging Phenotypes from XPD Mutations

Energy Technology Data Exchange (ETDEWEB)

Tainer, John; Fan, Li; Fuss, Jill O.; Cheng, Quen J.; Arvai, Andrew S.; Hammel, Michal; Roberts, Victoria A.; Cooper, Priscilla K.; Tainer, John A.

2008-06-02

Mutations in XPD helicase, required for nucleotide excision repair (NER) as part of the transcription/repair complex TFIIH, cause three distinct phenotypes: cancer-prone xeroderma pigmentosum (XP), or aging disorders Cockayne syndrome (CS), and trichothiodystrophy (TTD). To clarify molecular differences underlying these diseases, we determined crystal structures of the XPD catalytic core from Sulfolobus acidocaldarius and measured mutant enzyme activities. Substrate-binding grooves separate adjacent Rad51/RecA-like helicase domains (HD1, HD2) and an arch formed by 4FeS and Arch domains. XP mutations map along the HD1 ATP-binding edge and HD2 DNA-binding channel and impair helicase activity essential for NER. XP/CS mutations both impair helicase activity and likely affect HD2 functional movement. TTD mutants lose or retain helicase activity but map to sites in all four domains expected to cause framework defects impacting TFIIH integrity. These results provide a foundation for understanding disease consequences of mutations in XPD and related 4Fe-4S helicases including FancJ.

XPD Helicase Structures And Activities: Insights Into the Cancer And Aging Phenotypes From XPD Mutations

Energy Technology Data Exchange (ETDEWEB)

Fan, L.; Fuss, J.O.; Cheng, Q.J.; Arvai, A.S.; Hammel, M.; Roberts, V.A.; Cooper, P.K.; Tainer, J.A.

2009-05-18

Mutations in XPD helicase, required for nucleotide excision repair (NER) as part of the transcription/repair complex TFIIH, cause three distinct phenotypes: cancer-prone xeroderma pigmentosum (XP), or aging disorders Cockayne syndrome (CS), and trichothiodystrophy (TTD). To clarify molecular differences underlying these diseases, we determined crystal structures of the XPD catalytic core from Sulfolobus acidocaldarius and measured mutant enzyme activities. Substrate-binding grooves separate adjacent Rad51/RecA-like helicase domains (HD1, HD2) and an arch formed by 4FeS and Arch domains. XP mutations map along the HD1 ATP-binding edge and HD2 DNA-binding channel and impair helicase activity essential for NER. XP/CS mutations both impair helicase activity and likely affect HD2 functional movement. TTD mutants lose or retain helicase activity but map to sites in all four domains expected to cause framework defects impacting TFIIH integrity. These results provide a foundation for understanding disease consequences of mutations in XPD and related 4Fe-4S helicases including FancJ.

Statistical calculation of complete events in medium-energy nuclear collisions

International Nuclear Information System (INIS)

Randrup, J.

1984-01-01

Several heavy-ion accelerators throughout the world are presently able to deliver beams of heavy nuclei with kinetic energies in the range from tens to hundreds of MeV per nucleon, the so-called medium or intermediate energy range. At such energies a large number of final channels are open, each consisting of many nuclear fragments. The disassembly of the collision system is expected to be a very complicated process and a detailed dynamical description is beyond their present capability. However, by virtue of the complexity of the process, statistical considerations may be useful. A statistical description of the disassembly yields the least biased expectations about the outcome of a collision process and provides a meaningful reference against which more specific dynamical models, as well as the data, can be discussed. This lecture presents the essential tools for formulating a statistical model for the nuclear disassembly process. The authors consider the quick disassembly (explosion) of a hot nuclear system, a so-called source, into multifragment final states, which complete according to their statistical weight. First some useful notation is introduced. Then the expressions for exclusive and inclusive distributions are given and the factorization of an exclusive distribution into inclusive ones is carried out. In turn, the grand canonical approximation for one-fragment inclusive distributions is introduced. Finally, it is outlined how to generate a statistical sample of complete final states. On this basis, a model for statistical simulation of complete events in medium-energy nuclear collisions has been developed

Determination of C0-60 in Cobalt Slugs and Slabs and Radionuclides in Curium Sampler Slugs L-Reactor Disassembly Basin

International Nuclear Information System (INIS)

Casella, V.R.

2004-01-01

Co-60 was historically produced in the SRS reactors. Cobalt slugs were irradiated in the early 1970s. Post-production, remaining cobalt slugs (including slab form) were consolidated for storage. There are approximately nine hundred cobalt slugs currently stored awaiting final disposition. These slugs had historically incomplete documentation for activity rates; therefore, assaying was required in order to determine their activity levels. Since the gamma dose rate from these slugs is extremely high, the most cost effective way to shield a source of this magnitude from personnel and the radiation detector was to use the basin water in which the slugs are stored as the shield. A sodium iodide gamma detector was placed above a specially designed air collimator assembly, so that slug was at least eight feet from the detector and was shielded by the basin water. Using a sodium iodide detector and multichannel analyzer system and an underwater collimator assembly, Co-60 concentrations we re determined for Disassembly Basin cobalt slugs and slabs and 18 curium sampler slugs. The total activity of all of the assayed slugs summed to 31,783 curies. From the Co-60 concentrations of the curium sampler slugs, the irradiation flux was determined for the known irradiation time. The amounts of Pu-238, 239, 240, 241, 242; Am-241, 243; and Cm-242, 244 produced were then obtained based on the original amount of Pu-239 irradiated

Explosions of water clusters in intense laser fields

International Nuclear Information System (INIS)

Kumarappan, V.; Krishnamurthy, M.; Mathur, D.

2003-01-01

Energetic, highly charged oxygen ions O q+ (q≤6), are copiously produced upon laser field-induced disassembly of highly charged water clusters, (H 2 O) n and (D 2 O) n , n∼60, that are formed by seeding high-pressure helium or argon with water vapor. Ar n clusters (n∼40 000) formed under similar experimental conditions are found to undergo disassembly in the Coulomb explosion regime, with the energies of Ar q+ ions showing a q 2 dependence. Water clusters, which are argued to be considerably smaller in size, should also disassemble in the same regime, but the energies of fragment O q+ ions are found to depend linearly on q which, according to prevailing wisdom, ought to be a signature of hydrodynamic expansion that is expected of much larger clusters. The implication of these observations on our understanding of the two cluster explosion regimes, Coulomb explosion and hydrodynamic expansion, is discussed. Our results indicate that charge state dependences of ion energy do not constitute an unambiguous experimental signature of cluster explosion regime

Quantitative analysis of charge trapping and classification of sub-gap states in MoS2 TFT by pulse I-V method

Science.gov (United States)

Park, Junghak; Hur, Ji-Hyun; Jeon, Sanghun

2018-04-01

The threshold voltage instabilities and huge hysteresis of MoS2 thin film transistors (TFTs) have raised concerns about their practical applicability in next-generation switching devices. These behaviors are associated with charge trapping, which stems from tunneling to the adjacent trap site, interfacial redox reaction and interface and/or bulk trap states. In this report, we present quantitative analysis on the electron charge trapping mechanism of MoS2 TFT by fast pulse I-V method and the space charge limited current (SCLC) measurement. By adopting the fast pulse I-V method, we were able to obtain effective mobility. In addition, the origin of the trap states was identified by disassembling the sub-gap states into interface trap and bulk trap states by simple extraction analysis. These measurement methods and analyses enable not only quantitative extraction of various traps but also an understanding of the charge transport mechanism in MoS2 TFTs. The fast I-V data and SCLC data obtained under various measurement temperatures and ambient show that electron transport to neighboring trap sites by tunneling is the main charge trapping mechanism in thin-MoS2 TFTs. This implies that interfacial traps account for most of the total sub-gap states while the bulk trap contribution is negligible, at approximately 0.40% and 0.26% in air and vacuum ambient, respectively. Thus, control of the interface trap states is crucial to further improve the performance of devices with thin channels.

Disassembly and reassembly of human papillomavirus virus-like particles produces more virion-like antibody reactivity

Directory of Open Access Journals (Sweden)

Zhao Qinjian

2012-02-01

Full Text Available Abstract Background Human papillomavirus (HPV vaccines based on major capsid protein L1 are licensed in over 100 countries to prevent HPV infections. The yeast-derived recombinant quadrivalent HPV L1 vaccine, GARDASIL(R, has played an important role in reducing cancer and genital warts since its introduction in 2006. The L1 proteins self-assemble into virus-like particles (VLPs. Results VLPs were subjected to post-purification disassembly and reassembly (D/R treatment during bioprocessing to improve VLP immunoreactivity and stability. The post-D/R HPV16 VLPs and their complex with H16.V5 neutralizing antibody Fab fragments were visualized by cryo electron microscopy, showing VLPs densely decorated with antibody. Along with structural improvements, post-D/R VLPs showed markedly higher antigenicity to conformational and neutralizing monoclonal antibodies (mAbs H16.V5, H16.E70 and H263.A2, whereas binding to mAbs recognizing linear epitopes (H16.J4, H16.O7, and H16.H5 was greatly reduced. Strikingly, post-D/R VLPs showed no detectable binding to H16.H5, indicating that the H16.H5 epitope is not accessible in fully assembled VLPs. An atomic homology model of the entire HPV16 VLP was generated based on previously determined high-resolution structures of bovine papillomavirus and HPV16 L1 pentameric capsomeres. Conclusions D/R treatment of HPV16 L1 VLPs produces more homogeneous VLPs with more virion-like antibody reactivity. These effects can be attributed to a combination of more complete and regular assembly of the VLPs, better folding of L1, reduced non-specific disulfide-mediated aggregation and increased stability of the VLPs. Markedly different antigenicity of HPV16 VLPs was observed upon D/R treatment with a panel of monoclonal antibodies targeting neutralization sensitive epitopes. Multiple epitope-specific assays with a panel of mAbs with different properties and epitopes are required to gain a better understanding of the immunochemical

Control of cell volume in the J774 macrophage by microtubule disassembly and cyclic AMP

Science.gov (United States)

Melmed, RN; Karanian, PJ; Berlin, RD

1981-01-01

We have explored the possibilities that cell volume is regulated by the status of microtubule assembly and cyclic AMP metabolism and may be coordinated with shape change. Treatment of J774.2 mouse macrophages with colchicine caused rapid microtubule disassembly and was associated with a striking increase (from 15-20 to more than 90 percent) in the proportion of cells with a large protuberance at one pole. This provided a simple experimental system in which shape changes occurred in virtually an entire cell population in suspension. Parallel changes in cell volume could then be quantified by isotope dilution techniques. We found that the shape change caused by colchicine was accompanied by a decrease in cell volume of approximately 20 percent. Nocodozole, but not lumicolchicine, caused identical changes in both cell shape and cell volume. The volume loss was not due to cell lysis nor to inhibition of pinocytosis. The mechanism of volume loss was also examined. Colchicine induced a small but reproducible increase in activity of the ouabain-sensitive Na(+), K(+)-dependent ATPase. However, inhibition of this enzyme/transport system by ouabain did not change cell volume nor did it block the colchicines-induced decrease in volume. One the other hand, SITS (4’acetamido, 4-isothiocyano 2,2’ disulfonic acid stilbene), an inhibitor of anion transport, inhibited the effects of colchicines, thus suggesting a role for an anion transport system in cell volume regulation. Because colchicine is known to activate adenylate cyclase in several systems and because cell shape changes are often induced by hormones that elevate cyclic AMP, we also examined the effects of cyclic AMP on cell volume. Agents that act to increase syclic AMP (cholera toxin, which activates adenylate cyclase; IBMX, and inhibitor of phosphodiesterase; and dibutyryl cyclic AMP) all caused a volume decrease comparable to that of colchicine. To define the effective metabolic pathway, we studied two mutants of J

An integrated TSP-GA with EOL cost model for selecting the best EOL option

OpenAIRE

Zakri Ghazalli; Atsuo Murata

2011-01-01

This paper presents our research works on integrating design for disassembly with cost model for end-of-life (EOL) product. This paper has two objectives. The first objective is to optimize disassembly sequence of the EOL product. We integrate a traveling salesman problem approach with genetic algorithm in finding the optimal disassembly sequence for disassembling the EOL product. Based on this optimal sequence, the second objective is to identify the best EOL option. We employ EOL profits an...

76 FR 11363 - Defense Federal Acquisition Regulation Supplement; Government Support Contractor Access to...

Science.gov (United States)

2011-03-02

... the recipient to decompile, disassemble, or reverse engineer the software, or use software decompiled... engineer the software, or use software decompiled, disassembled, or reverse engineered by the Government... Government shall not permit the recipient to decompile, disassemble, or reverse engineer the software, or use...

Crystal structure of the FeS cluster-containing nucleotide excision repair helicase XPD.

Directory of Open Access Journals (Sweden)

Stefanie C Wolski

2008-06-01

Full Text Available DNA damage recognition by the nucleotide excision repair pathway requires an initial step identifying helical distortions in the DNA and a proofreading step verifying the presence of a lesion. This proofreading step is accomplished in eukaryotes by the TFIIH complex. The critical damage recognition component of TFIIH is the XPD protein, a DNA helicase that unwinds DNA and identifies the damage. Here, we describe the crystal structure of an archaeal XPD protein with high sequence identity to the human XPD protein that reveals how the structural helicase framework is combined with additional elements for strand separation and DNA scanning. Two RecA-like helicase domains are complemented by a 4Fe4S cluster domain, which has been implicated in damage recognition, and an alpha-helical domain. The first helicase domain together with the helical and 4Fe4S-cluster-containing domains form a central hole with a diameter sufficient in size to allow passage of a single stranded DNA. Based on our results, we suggest a model of how DNA is bound to the XPD protein, and can rationalize several of the mutations in the human XPD gene that lead to one of three severe diseases, xeroderma pigmentosum, Cockayne syndrome, and trichothiodystrophy.

Abnormal XPD-induced nuclear receptor transactivation in DNA repair disorders: trichothiodystrophy and xeroderma pigmentosum.

Science.gov (United States)

Zhou, Xiaolong; Khan, Sikandar G; Tamura, Deborah; Ueda, Takahiro; Boyle, Jennifer; Compe, Emmanuel; Egly, Jean-Marc; DiGiovanna, John J; Kraemer, Kenneth H

2013-08-01

XPD (ERCC2) is a DNA helicase involved in nucleotide excision repair and in transcription as a structural bridge tying the transcription factor IIH (TFIIH) core with the cdk-activating kinase complex, which phosphorylates nuclear receptors. Mutations in XPD are associated with several different phenotypes, including trichothiodystrophy (TTD), with sulfur-deficient brittle hair, bone defects, and developmental abnormalities without skin cancer, xeroderma pigmentosum (XP), with pigmentary abnormalities and increased skin cancer, or XP/TTD with combined features, including skin cancer. We describe the varied clinical features and mutations in nine patients examined at the National Institutes of Health who were compound heterozygotes for XPD mutations but had different clinical phenotypes: four TTD, three XP, and two combined XP/TTD. We studied TFIIH-dependent transactivation by nuclear receptor for vitamin D (VDR) and thyroid in cells from these patients. The vitamin D stimulation ratio of CYP24 and osteopontin was associated with specific pairs of mutations (reduced in 5, elevated in 1) but not correlated with distinct clinical phenotypes. Thyroid receptor stimulation ratio for KLF9 was not significantly different from normal. XPD mutations frequently were associated with abnormal VDR stimulation in compound heterozygote patients with TTD, XP, or XP/TTD.

Photoisomers of Azobenzene Star with a Flat Core: Theoretical Insights into Multiple States from DFT and MD Perspective.

Science.gov (United States)

Koch, Markus; Saphiannikova, Marina; Santer, Svetlana; Guskova, Olga

2017-09-21

This study focuses on comparing physical properties of photoisomers of an azobenzene star with benzene-1,3,5-tricarboxamide core. Three azobenzene arms of the molecule undergo a reversible trans-cis isomerization upon UV-vis light illumination giving rise to multiple states from the planar all-trans one, via two mixed states to the kinked all-cis isomer. Employing density functional theory, we characterize the structural and photophysical properties of each state indicating a role the planar core plays in the coupling between azobenzene chromophores. To characterize the light-triggered switching of solvophilicity/solvophobicity of the star, the difference in solvation free energy is calculated for the transfer of an azobenzene star from its gas phase to implicit or explicit solvents. For the latter case, classical all-atom molecular dynamics simulations of aqueous solutions of azobenzene star are performed employing the polymer consistent force field to shed light on the thermodynamics of explicit hydration as a function of the isomerization state and on the structuring of water around the star. From the analysis of two contributions to the free energy of hydration, the nonpolar van der Waals and the electrostatic terms, it is concluded that isomerization specificity largely determines the polarity of the molecule and the solute-solvent electrostatic interactions. This convertible hydrophilicity/hydrophobicity together with readjustable occupied volume and the surface area accessible to water, affects the self-assembly/disassembly of the azobenzene star with a flat core triggered by light.

Robot Control Using UML and Multi-agent System

Directory of Open Access Journals (Sweden)

Ales Pavliska

2003-02-01

Full Text Available Increased industrialization and new markets have led to an accumulation of used technical consumer goods, which results in greater exploitation of raw materials, energy and landfill sites. In order to reduce the use of natural resources conserve precious energy and limit the increase in waste volume. The application of disassembly techniques is the first step towards this prevention of waste. These techniques form a reliable and clean approach: "noble" or high-graded recycling. This paper presents a multi agent system for disassembly process, which is implemented in a computer-aided application for supervising of the disassembling system: the Interactive Intelligent Interface for Disassembling System. Unified modeling language diagrams are used for an internal and external definition of the disassembling system.

Homozygous Wildtype of XPD K751Q Polymorphism Is Associated with Increased Risk of Nasopharyngeal Carcinoma in Malaysian Population

OpenAIRE

Lye, Munn-Sann; Visuvanathan, Shaneeta; Chong, Pei-Pei; Yap, Yoke-Yeow; Lim, Chin-Chye; Ban, Eng-Zhuan

2015-01-01

The xeroderma pigmentosum group D (XPD) gene encodes a DNA helicase, an important component in transcription factor IIH (TFIIH) complex. XPD helicase plays a pivotal role in unwinding DNA at the damaged region during nucleotide excision repair (NER) mechanism. Dysfunctional XPD helicase protein from polymorphic diversity may contribute to increased risk of developing cancers. This study aims to determine the association between XPD K751Q polymorphism (rs13181) and risk of nasopharyngeal carci...

Secretome profiling of oral squamous cell carcinoma-associated fibroblasts reveals organization and disassembly of extracellular matrix and collagen metabolic process signatures.

Science.gov (United States)

Bagordakis, Elizabete; Sawazaki-Calone, Iris; Macedo, Carolina Carneiro Soares; Carnielli, Carolina M; de Oliveira, Carine Ervolino; Rodrigues, Priscila Campioni; Rangel, Ana Lucia C A; Dos Santos, Jean Nunes; Risteli, Juha; Graner, Edgard; Salo, Tuula; Paes Leme, Adriana Franco; Coletta, Ricardo D

2016-07-01

An important role has been attributed to cancer-associated fibroblasts (CAFs) in the tumorigenesis of oral squamous cell carcinoma (OSCC), the most common tumor of the oral cavity. Previous studies demonstrated that CAF-secreted molecules promote the proliferation and invasion of OSCC cells, inducing a more aggressive phenotype. In this study, we searched for differences in the secretome of CAFs and normal oral fibroblasts (NOF) using mass spectrometry-based proteomics and biological network analysis. Comparison of the secretome profiles revealed that upregulated proteins involved mainly in extracellular matrix organization and disassembly and collagen metabolism. Among the upregulated proteins were fibronectin type III domain-containing 1 (FNDC1), serpin peptidase inhibitor type 1 (SERPINE1), and stanniocalcin 2 (STC2), the upregulation of which was validated by quantitative PCR and ELISA in an independent set of CAF cell lines. The transition of transforming growth factor beta 1 (TGF-β1)-mediating NOFs into CAFs was accompanied by significant upregulation of FNDC1, SERPINE1, and STC2, confirming the participation of these proteins in the CAF-derived secretome. Type I collagen, the main constituent of the connective tissue, was also associated with several upregulated biological processes. The immunoexpression of type I collagen N-terminal propeptide (PINP) was significantly correlated in vivo with CAFs in the tumor front and was associated with significantly shortened survival of OSCC patients. Presence of CAFs in the tumor stroma was also an independent prognostic factor for OSCC disease-free survival. These results demonstrate the value of secretome profiling for evaluating the role of CAFs in the tumor microenvironment and identify potential novel therapeutic targets such as FNDC1, SERPINE1, and STC2. Furthermore, type I collagen expression by CAFs, represented by PINP levels, may be a prognostic marker of OSCC outcome.

Development of the SCHAMBETA code for scoping analysis of HCDA

Energy Technology Data Exchange (ETDEWEB)

Suk, Soo Dong; Hahn, D. H

2000-06-01

A computer code, SCHAMBETA(Scoping Code for HCDA Analysis using Modified Bethe-Tait Method), is developed to investigate the core disassembly process following a meltdown accident in the framework of a mofified Bethe-Tait method as part of the scoping analysis work to demonstrate the inherent safety of conceptual designs of Korea Advanced Liquid Metal Reactor(KALIMER), A 150 Mwe pool-type sodium cooled prototype fast reactor that uses U-Pu-Zr metallic fuel. The methodologies adopted in the code ared particularly useful to perform various parametric studies for better understanding of core disassembly process of liquid metal fast reactors as well as to estimate upper-limit values of the energy release resulting from a power excursion. In the SCHAMBETA code, the core kinetics and hydraulic behavior of the KALIMER is followed over the period of the super-prompt critical power excursion induced by the ramp reactivity insertion, starting at the time that the sodium-voided core reaches the melting temperature of the metallic fuels. For this purpose, the equations of state of pressure-energy density relationship are derived for the saturated-vapor as well as the solid liquid of metallic uranium fuel, and implemenmted into the formulations of the disassembly reactivity. Mathematical formulations are then developed, in the framework of Modified Bethe-Tait method, in a form relevant to utilize the improved equations of state as well as to consider Doppler effects, for scoping analysis of the super-prompt-critical power excursions driven by a specified rate of reactivity insertion.

Sports Management for Sports Massification Planned and Executed by Social Organizations. Critics to Models, Experiences and Proposal Methodological Accompaniment

OpenAIRE

Lorenza Antonia Reyes de Duran

2016-01-01

The proposal analysis, interpretation, disassembly, self-criticism and guidance is born and comes from work experience planned mass sports and social organizations opposed-not in the conventional sense comparative-private business models and sport, state and management. The contribution made by the sports management experience from positions of power, either state or business are undeniable and its impact is difficult to express in numbers for its humanistic value, which is incalculable. Howe...

The role of fission gas in the analysis of hypothetical core disruptive accidents

Energy Technology Data Exchange (ETDEWEB)

Fischer, E A [Gesellschaft fuer Kernforschung mbH, INR Kernforschungszentrum, Karlsruhe (Germany)

1977-07-01

This paper summarizes recent work at Karlsruhe with the goal of understanding the effects of fission gas in hypothetical core disruptive accidents. The fission gas behavior model is discussed. The computer programs LANGZEIT and KURZZEIT describe the long-term and the transient gas behavior, respectively. Recent improvements in the modeling and a comparison of results with experimental data are reported. A somewhat detailed study of the role of fission gas in transient overpower (TOP) accidents was carried out. If pessimistic assumptions, like pin failure near the axial midplane are made, these accidents end in core disassembly. The codes HOPE and KADIS were used to analyze the initiating and the disassembly phase in these studies. Improvements of the codes are discussed. They include an automatic data transfer from HOPE to KADIS, and a new equation of state in KADIS, with an improved model for fission gas behavior. The analysis of a 15 cents/sec reactivity ramp accident is presented. Different pin failure criteria are used. In the cases selected, the codes predict an energetic disassembly. For the much discussed loss-of-flow driven TOP, detailed models are presently not available at Karlsruhe. Therefore, only a few comments and the results of a few scoping calculations will be presented.

Vandellos 1 decommissioning project. Safety before, during and after

International Nuclear Information System (INIS)

Rodriguez, A.

2002-01-01

The Nuclear Power Plant of Vandellos 1, a gas-graphite reactor (GCR), started operation in the 70's after 17 years running the decommissioning process began in 1998, and is expected to finish at the end of 2002 with the level 2 of decommissioning with a practically total scope reached, except the concrete reactor vessel and its internals that will remain for another 25 years in surveillance state (dormancy) until their total dismantling. During the last four years the activities related to decontamination and disassembly of the power plant system as well as the management of all this material have been carried out. One of the last phases of the project that will be performed this year, without doubt, one of the most representative of the operative difficulty of the task is the disassembly of some buildings which are more than 80 meters high and with some structures weighing more than 3.000 t, an operation, which is spectacular in terms of volume and mass involved. However one has to keep in mind that it has been preceded by the of clearance process of all these structures to be disassembled this summer. Hundred of thousands of radiological measures will confirm with guarantee that the destination of the dismantled materials is the correct one, assuring the protection of people and the environment. This is a process which has to integrate the principles of radiological safety and industrial safety. First, it has to be guaranteed that structures and components are below the values authorised by authorities for their free release, and, secondly, that the planned sequence of the process and manoeuvres in the disassembly of these colossal structures assures safety. (author)

Cdk1 and okadaic acid-sensitive phosphatases control assembly of nuclear pore complexes in Drosophila embryos.

Science.gov (United States)

Onischenko, Evgeny A; Gubanova, Natalia V; Kiseleva, Elena V; Hallberg, Einar

2005-11-01

Disassembly and reassembly of the nuclear pore complexes (NPCs) is one of the major events during open mitosis in higher eukaryotes. However, how this process is controlled by the mitotic machinery is not clear. To investigate this we developed a novel in vivo model system based on syncytial Drosophila embryos. We microinjected different mitotic effectors into the embryonic cytoplasm and monitored the dynamics of disassembly/reassembly of NPCs in live embryos using fluorescently labeled wheat germ agglutinin (WGA) or in fixed embryos using electron microscopy and immunostaining techniques. We found that in live embryos Cdk1 activity was necessary and sufficient to induce disassembly of NPCs as well as their cytoplasmic mimics: annulate lamellae pore complexes (ALPCs). Cdk1 activity was also required for keeping NPCs and ALPCs disassembled during mitosis. In agreement recombinant Cdk1/cyclin B was able to induce phosphorylation and dissociation of nucleoporins from the NPCs in vitro. Conversely, reassembly of NPCs and ALPCs was dependent on the activity of protein phosphatases, sensitive to okadaic acid (OA). Our findings suggest a model where mitotic disassembly/reassembly of the NPCs is regulated by a dynamic equilibrium of Cdk1 and OA-sensitive phosphatase activities and provide evidence that mitotic phosphorylation mediates disassembly of the NPC.

An integrated TSP-GA with EOL cost model for selecting the best EOL option

Directory of Open Access Journals (Sweden)

Zakri Ghazalli

2011-10-01

Full Text Available This paper presents our research works on integrating design for disassembly with cost model for end-of-life (EOL product. This paper has two objectives. The first objective is to optimize disassembly sequence of the EOL product. We integrate a traveling salesman problem approach with genetic algorithm in finding the optimal disassembly sequence for disassembling the EOL product. Based on this optimal sequence, the second objective is to identify the best EOL option. We employ EOL profits and net present value of parts and subassemblies of the EOL product to determine the best EOL option of components and parts of the EOL product. The predicted results showed that the developed cost model has reached a good correspondence with the established methods.

Development of spent fuel remote handling technology

International Nuclear Information System (INIS)

Yoon, Ji Sup; Park, B. S.; Park, Y. S.; Oh, S. C.; Kim, S. H.; Cho, M. W.; Hong, D. H.

1997-12-01

Since the nation's policy on spent fuel management is not finalized, the technical items commonly required for safe management and recycling of spent fuel - remote technologies of transportation, inspection, maintenance, and disassembly of spent fuel - are selected and pursued. In this regards, the following R and D activities are carried out : collision free transportation of spent fuel assembly, mechanical disassembly of spent nuclear fuel and graphical simulation of fuel handling / disassembly process. (author). 36 refs., 16 tabs., 77 figs

Heat evaluation examination of fuel assembly

International Nuclear Information System (INIS)

Suto, Shinya; Nakabayashi, Hiroki; Yao, Kaoru

2007-03-01

The cooling examination was executed by using the simulated fuel assembly to obtain the basic data of the most effective cooling system in the lazer disassembling process of the spent fuel assembly of prototype fast breeder reactor 'Monju'. As a result, the following have been understood. (1) Before the laser disassembling (there is not any duct tube cutting), it is possible to cool enough by the amount of the wind of 20m 3 /h or more flowing from the handling head side. (2) After the laser disassembling begins (duct tube is cut), 1kW or more of the heat generation cannot be cooled by ventilation from the handling head side. (3) Cooling by the flow across fuel pin is required during lazer disassembling. The basic data of the cooling system was obtained from these examination results. However, for cooling across fuel pin during the laser disassembling, it is necessary to examine shape of the side cooling nozzle, spraying angle, and flow velocity at the nozzle exit, etc. enough. (author)

New findings on the onset of thermal disassembly in spallation reactions; Nouvelles approches pour l'etude de la multifragmentation thermique dans la spallation

Energy Technology Data Exchange (ETDEWEB)

Napolitani, P

2004-09-15

Thermal multifragmentation is the process of multi body disassembly of a hot nucleus when the excitation is almost purely thermal i.e. dynamical effects like compression (characteristic of ion-ion collisions at Fermi energy) are negligible. Suited reactions are proton induced collision or ion-ion abrasion at relativistic incident energy. Thus we measured four systems at FRS (Fragment separator, GSI, Darmstadt) in inverse kinematics: Fe{sup 56}+p, Fe{sup 56}+Ti(nat), Xe{sup 136}+p, Xe{sup 136}+Ti(nat) a 1 A*GeV. The inverse kinematics allows to observe all particles without any threshold in energy. This is a great advantage compared to experiments in direct kinematics, because only in inverse kinematics it is possible to obtain complete velocity spectra (without a hole for low velocities) for fully identified isotopes. The complex shape of the velocity spectra allows to identify the different deexcitation channels and it clearly shows the transition from a chaotic-dominated process (Gaussian cloud in velocity space) to a direct Coulomb- (or eventually expansion-) dominated process (shell of a sphere in velocity space). Different possible descriptions of the reaction process are discussed, based either on asymmetric fission or multifragmentation. The resulting physical picture is especially interesting for the Fe{sup 56}+p, and Xe{sup 136}+p systems: proton induced collisions could result in the split of the system in two or more fragments due to a fast break-up process. In this case, the configuration of the break-up partition is very asymmetric. The discussion will be extended to other characteristics, like the restoring of nuclear structure features in the isotopic production and the temperature dependence of the isotopic composition of the residues. (author)

Dismantling the activated annular water tank of the Rheinsberg nuclear power plant

International Nuclear Information System (INIS)

Klietz, Maik; Konitzer, Arnold; Luedeke, Michael

2010-01-01

Acting on behalf of Energiewerke Nord GmbH Lubmin, Anlagen- und Kraftwerksrohrleitungsbau Greifswald GmbH (AKB) planned and built a station for disassembly of the activated annular water tank (RWB) of the decommissioned Rheinsberg nuclear power plant. As part of this demolition step, the annular water tank must be conditioned and disposed of as a component of the reactor facility. This required planning, manufacturing, testing and construction on site of suitable disassembly and handling techniques and the necessary plant and equipment. The client opted for disassembly by means of a diamond cable saw for conditioning the annular water tank into segments fit for shipping, and defined the basic components for the disassembly station in a specification of deliveries and services. The disassembly station serves to divide the annular water tank by means of diamond cable saws into 2 sections in such a way that segment pieces for transport are produced. The existing activation of the annular water tank also entailed the need to plan for the shortest possible time to be spent on handling near the annular water tank, providing radiological protection to the personnel, and performing the sawing steps from a separate operating console assisted by camera surveillance. After works acceptance tests at the manufacturer's, AKB, in October 2009 and February 2010, the disassembly station was delivered to the customer at Rheinsberg KKR free from defects in June 2010. (orig.)

The role of fission products in whole core accidents

Energy Technology Data Exchange (ETDEWEB)

Baker, A R [FRSD, UKAEA, RNPDE, Risley, Warrington (United Kingdom); Teague, H J [SRD, UKAEA, Culcheth, Warrington (United Kingdom)

1977-07-01

The review of the role of fission products in whole-core accidents falls into two parts. Firstly, there is a discussion of the hypothetical accidents usually considered in the UK and how they are dealt with. Secondly, there is a discussion of individual topics where fission products are known to be important or might be so. There is a brief discussion of the UK work on the establishment of an equation of state for unirradiated fuel and how this might be extended to incorporate fission product effects. The main issue is the contribution of fission products to the effective vapour pressure and the experimental programme on the pulsed reactor VIPER investigates this. Fission products may influence the probability of occurrence and the severity of MFCIs. Finally, the fission product effects in the pre-disassembly, disassembly and recriticality stages of an accident are discussed. (author)

Development of spent fuel remote handling technology

Energy Technology Data Exchange (ETDEWEB)

Yoon, Ji Sup; Park, B S; Park, Y S; Oh, S C; Kim, S H; Cho, M W; Hong, D H

1997-12-01

Since the nation`s policy on spent fuel management is not finalized, the technical items commonly required for safe management and recycling of spent fuel - remote technologies of transportation, inspection, maintenance, and disassembly of spent fuel - are selected and pursued. In this regards, the following R and D activities are carried out : collision free transportation of spent fuel assembly, mechanical disassembly of spent nuclear fuel and graphical simulation of fuel handling / disassembly process. (author). 36 refs., 16 tabs., 77 figs

Manipulator and materials handling systems for reactor decommissioning -Cooperation between the university and the plant operator

International Nuclear Information System (INIS)

Schreck, G.; Bach, F. W.; Haferkamp, H.

1995-01-01

Nuclear reactor dismantling requires suitable handling systems for tools and disassembled components, as well as qualified and reliable disassembly and cutting techniques. From the angle of radiation protection, remote-controlled handling techniques and underwater techniques are the methods of choice, the latter particularly in continuation of plant operating conditions, and this all the more the more disassembly work proceeds towards the reactor core. With the experience accumulated for 20 years now by the Institut fuer Werkstoffkunde (materials science) of Hannover University by basic research and application-oriented development work in the field of thermal cutting technology, especially plasma arc cutting techniques, as well as development work in the field of remote-controlled materials handling systems, the institute is the cut-out partner for disassembly tasks in reactor decommissioning. (Orig./DG) [de

Dry spent-fuel consolidation demonstration at the Barnwell Nuclear Fuel Plant (BNFP)

International Nuclear Information System (INIS)

Townes, G.A.

1982-08-01

Equipment for disassembling and canning (or encapsulating) spent fuel to allow more efficient storage is being developed and demonstrated at the BNFP. The program is aimed at dry disassembly of fuel to allow storage and shipment of fuel pins rather than full fuel assemblies. Results indicate that doubling the existing storage capacity or tripling the carrying capacity of existing transportation equipment is achievable. Disassembly has been demonstrated in the BNFP hot cells at rates of approx. 10 to 12 assemblies per day. 3 figures

A study on constructing a machine-maintenance training system based on virtual reality technology

International Nuclear Information System (INIS)

Ishii, H.; Kashiwa, K.; Tezuka, T.; Yoshikawa, H.

1997-01-01

The development of a VR based training system are presented for teaching disassembling procedures of mechanical machines used in nuclear power plant. The methods of Petri net model for describing trainees' plausible actions in the disassembling process and reduce a right sequence of action sequence are developed as well as realization of the related Petri net editor and the demonstration of the developed VR based training system was demonstrated by example practice of disassembly simulation of check valve. Moreover, the needed future works are also discussed

JPRS Report Soviet Union Political Affairs.

Science.gov (United States)

1990-07-19

gentsia, specialists, authoritative workers and kolkhoz farmers in on their deliberations. A soviet of primary party organization secretaries...are in favor of disassembling the authoritarian , bureaucratic system and for focusing on humane, democratic socialism, the forming of a state under...Iolota’nskiy Rayon in Turkmenistan a boarding home for mentally retarded children. Some end up here directly from maternity homes, others are brought by

Supramolecular Lego assembly towards three-dimensional multi-responsive hydrogels.

Science.gov (United States)

Ma, Chunxin; Li, Tiefeng; Zhao, Qian; Yang, Xuxu; Wu, Jingjun; Luo, Yingwu; Xie, Tao

2014-08-27

Inspired by the assembly of Lego toys, hydrogel building blocks with heterogeneous responsiveness are assembled utilizing macroscopic supramolecular recognition as the adhesion force. The Lego hydrogel provides 3D transformation upon pH variation. After disassembly of the building blocks by changing the oxidation state, they can be re-assembled into a completely new shape. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Correlation between femoral offset loss and dynamic hip screw cut-out complications after pertrochanteric fractures: a case-control study.

Science.gov (United States)

Boukebous, Baptiste; Guillon, Pascal; Vandenbussche, Eric; Rousseau, Marc Antoine

2018-04-27

Screw-plates disassembly incidence after pertrochanteric fracture (PF) amounts to 1 and 16% among the elderly population. The main occurrence is early cervical screw cut-out. The population at highest risk of disassembly remains difficult to identify. The correlation between femoral offset loss and disassembly occurrence has never been surveyed. A radiological prognosis score for screw plate disassembly was defined to reflect trochanteric impaction (TI); it was based on a femoral offset ratio. Our single-centre retrospective case-control study surveyed patients suffering from Dynamic Hip Screw (DHS, Synthes ® ) disassembly following osteosynthesis of non-pathological osteoporotic PF between 2004 and 2014. All cases were categorised by age and gender and paired to three patients in the control group. The primary endpoint was TI measurement, corresponding to offset loss on the operated hip compared to healthy hip offset and expressed as a percentage. The measurement was done on an immediate postoperative X-ray. The secondary endpoints were tip apex distance (TAD) measurement, Ender and AO classifications, as well as postoperative weight-bearing prescription. Twenty-three cases and 69 controls were surveyed. The case group's average age was 87; 70% of the cases were women. The main disassembly occurrence delay was after 27 days. Average TI was 26% within the patients global group and 12% within the control group (p  21%. Using the offset ratio tool, TI measurement was associated with a greater risk of DHS disassembly when it was higher than 21%. The exclusive use of a DHS device does not seem optimal for a TI > 21%. Weight-bearing may be prescribed for all the patients with a TI < 21%, provided good implant positioning is secured.

Dismantling the activated annular water tank of the Rheinsberg nuclear power plant; Zerlegung des aktivierten Ringwasserbehaelters des Kernkraftwerks Rheinsberg

Energy Technology Data Exchange (ETDEWEB)

Klietz, Maik; Konitzer, Arnold; Luedeke, Michael [Anlagen- und Kraftwerksrohrleitungsbau GmbH, Greifswald (Germany)

2010-10-15

Acting on behalf of Energiewerke Nord GmbH Lubmin, Anlagen- und Kraftwerksrohrleitungsbau Greifswald GmbH (AKB) planned and built a station for disassembly of the activated annular water tank (RWB) of the decommissioned Rheinsberg nuclear power plant. As part of this demolition step, the annular water tank must be conditioned and disposed of as a component of the reactor facility. This required planning, manufacturing, testing and construction on site of suitable disassembly and handling techniques and the necessary plant and equipment. The client opted for disassembly by means of a diamond cable saw for conditioning the annular water tank into segments fit for shipping, and defined the basic components for the disassembly station in a specification of deliveries and services. The disassembly station serves to divide the annular water tank by means of diamond cable saws into 2 sections in such a way that segment pieces for transport are produced. The existing activation of the annular water tank also entailed the need to plan for the shortest possible time to be spent on handling near the annular water tank, providing radiological protection to the personnel, and performing the sawing steps from a separate operating console assisted by camera surveillance. After works acceptance tests at the manufacturer's, AKB, in October 2009 and February 2010, the disassembly station was delivered to the customer at Rheinsberg KKR free from defects in June 2010. (orig.)

Retail Deli Slicer Cleaning Frequency--Six Selected Sites, United States, 2012.

Science.gov (United States)

Brown, Laura G; Hoover, E Rickamer; Ripley, Danny; Matis, Bailey; Nicholas, David; Hedeen, Nicole; Faw, Brenda

2016-04-01

Listeria monocytogenes (Listeria) causes the third highest number of foodborne illness deaths (an estimated 255) in the United States annually, after nontyphoidal Salmonella species and Toxoplasma gondii (1). Deli meats are a major source of listeriosis illnesses, and meats sliced and packaged at retail delis are the major source of listeriosis illnesses attributed to deli meat (4). Mechanical slicers pose cross-contamination risks in delis and are an important source of Listeria cross-contamination. Reducing Listeria contamination of sliced meats in delis will likely reduce Listeria illnesses and outbreaks. Good slicer cleaning practices can reduce this foodborne illness risk. CDC's Environmental Health Specialists Network (EHS-Net) studied how often retail deli slicers were fully cleaned (disassembled, cleaned, and sanitized) at the Food and Drug Administration (FDA) Food Code-specified minimum frequency of every 4 hours and examined deli and staff characteristics related to slicer cleaning frequency. Interviews with staff members in 298 randomly-selected delis in six EHS-Net sites showed that approximately half of delis fully cleaned their slicers less often than FDA's specified minimum frequency. Chain-owned delis and delis with more customers, more slicers, required manager food safety training, food safety-knowledgeable workers, written slicer-cleaning policies, and food safety-certified managers fully cleaned their slicers more frequently than did other types of delis, according to deli managers or workers. States and localities should require deli manager training and certification, as specified in the FDA Food Code. They should also consider encouraging or requiring delis to have written slicer-cleaning policies. Retail food industry leaders can also implement these prevention efforts to reduce risk in their establishments. Because independent and smaller delis had lower frequencies of slicer cleaning, prevention efforts should focus on these types of

Uncoupling of dynamin polymerization and GTPase activity revealed by the conformation-specific nanobody dynab.

Science.gov (United States)

Galli, Valentina; Sebastian, Rafael; Moutel, Sandrine; Ecard, Jason; Perez, Franck; Roux, Aurélien

2017-10-12

Dynamin is a large GTPase that forms a helical collar at the neck of endocytic pits, and catalyzes membrane fission (Schmid and Frolov, 2011; Ferguson and De Camilli, 2012). Dynamin fission reaction is strictly dependent on GTP hydrolysis, but how fission is mediated is still debated (Antonny et al., 2016): GTP energy could be spent in membrane constriction required for fission, or in disassembly of the dynamin polymer to trigger fission. To follow dynamin GTP hydrolysis at endocytic pits, we generated a conformation-specific nanobody called dynab, that binds preferentially to the GTP hydrolytic state of dynamin-1. Dynab allowed us to follow the GTPase activity of dynamin-1 in real-time. We show that in fibroblasts, dynamin GTP hydrolysis occurs as stochastic bursts, which are randomly distributed relatively to the peak of dynamin assembly. Thus, dynamin disassembly is not coupled to GTPase activity, supporting that the GTP energy is primarily spent in constriction.

Regulatory assembly of the vacuolar proton pump VoV1-ATPase in yeast cells by FLIM-FRET

Science.gov (United States)

Ernst, Stefan; Batisse, Claire; Zarrabi, Nawid; Böttcher, Bettina; Börsch, Michael

2010-02-01

We investigate the reversible disassembly of VOV1-ATPase in life yeast cells by time resolved confocal FRET imaging. VOV1-ATPase in the vacuolar membrane pumps protons from the cytosol into the vacuole. VOV1-ATPase is a rotary biological nanomotor driven by ATP hydrolysis. The emerging proton gradient is used for secondary transport processes as well as for pH and Ca2+ homoeostasis in the cell. The activity of the VOV1-ATPase is regulated through assembly / disassembly processes. During starvation the two parts of VOV1-ATPase start to disassemble. This process is reversed after addition of glucose. The exact mechanisms are unknown. To follow the disassembly / reassembly in vivo we tagged two subunits C and E with different fluorescent proteins. Cellular distributions of C and E were monitored using a duty cycle-optimized alternating laser excitation scheme (DCO-ALEX) for time resolved confocal FRET-FLIM measurements.

DNA controlled assembly of liposomes

DEFF Research Database (Denmark)

Vogel, Stefan; Jakobsen, Ulla; Simonsen, Adam Cohen

2009-01-01

DNA-encoding of solid nanoparticles requires surfacechemistry, which is often tedious and not generally applicable. In the present study non-covalently attached DNA are used to assemble soft nanoparticles (liposomes) in solution. This process displays remarkably sharp thermal transitions from...... assembled to disassembled state for which reason this method allows easy and fast detection of polynucleotides (e.g. DNA or RNA), including single nucleotide polymorphisms as well as insertions and deletions....

Pull remanufacturing: A case study

Energy Technology Data Exchange (ETDEWEB)

Levine, L.O.

1992-09-01

This paper describes how pull production methods have been applied to a manual transmission remanufacturing line at Tooele Army Depot in Utah. The paper emphasizes techniques for linking the control of disassembly and cleaning operations to the repair and assembly portions of the production system (PP&C). The primary objective is to show that production planning and control can be simplified when pull mechanisms are combined with shop floor improvements. One approach to applying MRP II to remanufacturing is to use a separate production schedule for the disassembly and assembly portions of the operation. This approach is primarily needed when managing the delivery and inventory of cores is critical to the successful operation of a remanufacturing organization. Because Army depots frequently have an adequate inventory of cores on hand (somewhere on-site), this requirement is usually less significant. Therefore, it is possible to eliminate the use of a master production schedule for disassembly and rely on pull linkages from the repair and assembly operations to control the activity of the disassembly and cleaning operations. In remanufacturing environments having multiple products and adequate buffers of core inventory, effective coordination of disassembly and cleaning functions with assembly production requirements becomes a key production control issue.

Pull remanufacturing: A case study

Energy Technology Data Exchange (ETDEWEB)

Levine, L.O.

1992-09-01

This paper describes how pull production methods have been applied to a manual transmission remanufacturing line at Tooele Army Depot in Utah. The paper emphasizes techniques for linking the control of disassembly and cleaning operations to the repair and assembly portions of the production system (PP C). The primary objective is to show that production planning and control can be simplified when pull mechanisms are combined with shop floor improvements. One approach to applying MRP II to remanufacturing is to use a separate production schedule for the disassembly and assembly portions of the operation. This approach is primarily needed when managing the delivery and inventory of cores is critical to the successful operation of a remanufacturing organization. Because Army depots frequently have an adequate inventory of cores on hand (somewhere on-site), this requirement is usually less significant. Therefore, it is possible to eliminate the use of a master production schedule for disassembly and rely on pull linkages from the repair and assembly operations to control the activity of the disassembly and cleaning operations. In remanufacturing environments having multiple products and adequate buffers of core inventory, effective coordination of disassembly and cleaning functions with assembly production requirements becomes a key production control issue.

Methylation-regulated decommissioning of multimeric PP2A complexes

Energy Technology Data Exchange (ETDEWEB)

Wu, Cheng-Guo; Zheng, Aiping; Jiang, Li; Rowse, Michael; Stanevich, Vitali; Chen, Hui; Li, Yitong; Satyshur, Kenneth A.; Johnson, Benjamin; Gu, Ting-Jia; Liu, Zuojia; Xing, Yongna

2017-12-01

Dynamic assembly/disassembly of signaling complexes are crucial for cellular functions. Specialized latency and activation chaperones control the biogenesis of protein phosphatase 2A (PP2A) holoenzymes that contain a common scaffold and catalytic subunits and a variable regulatory subunit. Here we show that the butterfly-shaped TIPRL (TOR signaling pathway regulator) makes highly integrative multibranching contacts with the PP2A catalytic subunit, selective for the unmethylated tail and perturbing/inactivating the phosphatase active site. TIPRL also makes unusual wobble contacts with the scaffold subunit, allowing TIPRL, but not the overlapping regulatory subunits, to tolerate disease-associated PP2A mutations, resulting in reduced holoenzyme assembly and enhanced inactivation of mutant PP2A. Strikingly, TIPRL and the latency chaperone, α4, coordinate to disassemble active holoenzymes into latent PP2A, strictly controlled by methylation. Our study reveals a mechanism for methylation-responsive inactivation and holoenzyme disassembly, illustrating the complexity of regulation/signaling, dynamic complex disassembly, and disease mutations in cancer and intellectual disability.

Development of a dexterous manipulator system with redundant degrees of freedom

International Nuclear Information System (INIS)

Senoh, M.; Suzuki, M.; Tsuchita, K.; Kamimura, H.; Fujii, M.; Otsu, M.

1987-01-01

To keep plant availability as high as possible, more flexible and higher performance robots are desirable. At the same time, lower radiation exposures to operating personnel can be achieved by employing more sophisticated robotic systems. A new maintenance system has been proposed to realize consecutive disassembling and inspecting tasks by a robotic approach. The maintenance system includes three subsystems: a subsystem for the minor disassembling operations in the field; a transportation subsystem, which carries disassembled machines or components from the place where they were installed to a maintenance shop; and a subsystem for consecutive disassembling and grooming operations. Of these three subsystems, the maintenance robot for the first is the most challenging, and much development work is needed in the area of maneuverability in narrow spaces and obstacle avoidance ability. A master/slave-type manipulator with redundant degrees of freedom, mounted on a vehicle that travels along a spatially located railway, has been developed

Simulation of machine-maintenance training in virtual environment

International Nuclear Information System (INIS)

Yoshikawa, Hidekazu; Tezuka, Tetsuo; Kashiwa, Ken-ichiro; Ishii, Hirotake

1997-01-01

The periodical inspection of nuclear power plants needs a lot of workforces with a high degree of technical skill for the maintenance of various sorts of machines. Therefore, a new type of maintenance training system is required, where trainees can get training safely, easily and effectively. In this study we developed a training simulation system for disassembling a check valve in virtual environment (VE). The features of this system are as follows: Firstly, the trainees can execute tasks even in wrong order, and can experience the resultant conditions. In order to realize this environment, we developed a new Petri-net model for representing the objects' states in VE. This Petri-net model has several original characteristics, which make it easier to manage the change of the objects' states. Furthermore, we made a support system for constructing the Petri-net model of machine-disassembling training, because the Petri-net model is apt to become of large size. The effectiveness of this support system is shown through the system development. Secondly, this system can perform appropriate tasks to be done next in VE whenever the trainee wants even after some mistakes have been made. The effectiveness of this function has also been confirmed by experiments. (author)

Xeroderma Pigmentosum-Trichothiodystrophy overlap patient with novel XPD/ERCC2 mutation

DEFF Research Database (Denmark)

Kralund, Henrik H; Ousager, Lilian; Jaspers, Nicolaas G

2013-01-01

outcome from many of these mutations. We demonstrate a patient, believed to represent an overlap between XP and TTD/CS. In addition to other organ dysfunctions, the young man presented with Photosensitivity, Ichthyosis, Brittle hair, Impaired physical and mental development, Decreased fertility and Short...... appearance also suggested XP, but fibroblast cultures only demonstrated x2 UV-sensitivity with expected NER and TFIIH-activity decrease. Genetic sequencing of the XPD/ERCC2 gene established the patient as heterozygote compound with a novel, N-terminal Y18H mutation and a known C-terminal (TTD) mutation, A725...

Analysis of energy released from core disruptive accident of sodium cooled fast reactor using CDA-ER and VENUS-II codes

Energy Technology Data Exchange (ETDEWEB)

Kang, S. H.; Ha, K. S. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-05-15

The fast reactor has a unique feature in that rearranged core materials can produce a large increase in reactivity and recriticality. If such a rearrangement of core materials should occur rapidly, there would be a high rate of reactivity increase producing power excursions. The released energy from such an energetic recriticality might challenge the reactor vessel integrity. An analysis of the hypothetical excursions that result in the disassembly of the reactor plays an important role in a liquid metal fast reactor (LMFR) safety analysis. The analysis of such excursions generally consists of three phases (initial or pre-disassembly phase, disassembly phase, energy-work conversion phase). The first step is referred to as the 'accident initiation' or 'pre-disassembly' phase. In this phase, the accident is traced from some initiating event, such as a coolant pump failure or control rod ejection, up to a prompt critical condition where high temperatures and pressures rapidly develop in the core. Such complex processes as fuel pin failure, sodium voiding, and fuel slumping are treated in this phase. Several computer programs are available for this type of calculation, including SAS4A, MELT-II and FREADM. A number of models have been developed for this type of analysis, including the REXCO and SOCOOL-II computer programs. VENUS-II deals with the second phase (disassembly analysis). Most of the models used in the code have been based on the original work of Bethe and Tait. The disassembly motion is calculated using a set of two-dimensional hydrodynamics equations in the VENUS code. The density changes can be explicitly calculated, which in turn allows the use of a more accurate density dependent equation of state. The main functional parts of the computational model can be summarized as follows: Power and energy (point kinetics), Temperature (energy balance), Internal pressure (equation of state), Material displacement (hydrodynamics), Reactivity

Analysis of energy released from core disruptive accident of sodium cooled fast reactor using CDA-ER and VENUS-II codes

International Nuclear Information System (INIS)

Kang, S. H.; Ha, K. S.

2013-01-01

The fast reactor has a unique feature in that rearranged core materials can produce a large increase in reactivity and recriticality. If such a rearrangement of core materials should occur rapidly, there would be a high rate of reactivity increase producing power excursions. The released energy from such an energetic recriticality might challenge the reactor vessel integrity. An analysis of the hypothetical excursions that result in the disassembly of the reactor plays an important role in a liquid metal fast reactor (LMFR) safety analysis. The analysis of such excursions generally consists of three phases (initial or pre-disassembly phase, disassembly phase, energy-work conversion phase). The first step is referred to as the 'accident initiation' or 'pre-disassembly' phase. In this phase, the accident is traced from some initiating event, such as a coolant pump failure or control rod ejection, up to a prompt critical condition where high temperatures and pressures rapidly develop in the core. Such complex processes as fuel pin failure, sodium voiding, and fuel slumping are treated in this phase. Several computer programs are available for this type of calculation, including SAS4A, MELT-II and FREADM. A number of models have been developed for this type of analysis, including the REXCO and SOCOOL-II computer programs. VENUS-II deals with the second phase (disassembly analysis). Most of the models used in the code have been based on the original work of Bethe and Tait. The disassembly motion is calculated using a set of two-dimensional hydrodynamics equations in the VENUS code. The density changes can be explicitly calculated, which in turn allows the use of a more accurate density dependent equation of state. The main functional parts of the computational model can be summarized as follows: Power and energy (point kinetics), Temperature (energy balance), Internal pressure (equation of state), Material displacement (hydrodynamics), Reactivity feedback (Doppler and

Facility Decontamination and Decommissioning Program Surveillance and Maintenance Plan, Revision 2

Energy Technology Data Exchange (ETDEWEB)

Poderis, Reed J. [NSTec; King, Rebecca A. [NSTec

2013-09-30

This Surveillance and Maintenance (S&M) Plan describes the activities performed between deactivation and final decommissioning of the following facilities located on the Nevada National Security Site, as documented in the Federal Facility Agreement and Consent Order under the Industrial Sites program as decontamination and decommissioning sites: ? Engine Maintenance, Assembly, and Disassembly (EMAD) Facility: o EMAD Building (Building 25-3900) o Locomotive Storage Shed (Building 25-3901) ? Test Cell C (TCC) Facility: o Equipment Building (Building 25-3220) o Motor Drive Building (Building 25-3230) o Pump Shop (Building 25-3231) o Cryogenic Lab (Building 25-3232) o Ancillary Structures (e.g., dewars, water tower, piping, tanks) These facilities have been declared excess and are in various stages of deactivation (low-risk, long-term stewardship disposition state). This S&M Plan establishes and implements a solid, cost-effective, and balanced S&M program consistent with federal, state, and regulatory requirements. A graded approach is used to plan and conduct S&M activities. The goal is to maintain the facilities in a safe condition in a cost-effective manner until their final end state is achieved. This plan accomplishes the following: ? Establishes S&M objectives and framework ? Identifies programmatic guidance for S&M activities to be conducted by National Security Technologies, LLC, for the U.S. Department of Energy, National Nuclear Security Administration Nevada Field Office (NNSA/NFO) ? Provides present facility condition information and identifies hazards ? Identifies facility-specific S&M activities to be performed and their frequency ? Identifies regulatory drivers, NNSA/NFO policies and procedures, and best management practices that necessitate implementation of S&M activities ? Provides criteria and frequencies for revisions and updates ? Establishes the process for identifying and dispositioning a condition that has not been previously identified or

A molecular breadboard: Removal and replacement of subunits in a hepatitis B virus capsid.

Science.gov (United States)

Lee, Lye Siang; Brunk, Nicholas; Haywood, Daniel G; Keifer, David; Pierson, Elizabeth; Kondylis, Panagiotis; Wang, Joseph Che-Yen; Jacobson, Stephen C; Jarrold, Martin F; Zlotnick, Adam

2017-11-01

Hepatitis B virus (HBV) core protein is a model system for studying assembly and disassembly of icosahedral structures. Controlling disassembly will allow re-engineering the 120 subunit HBV capsid, making it a molecular breadboard. We examined removal of subunits from partially crosslinked capsids to form stable incomplete particles. To characterize incomplete capsids, we used two single molecule techniques, resistive-pulse sensing and charge detection mass spectrometry. We expected to find a binomial distribution of capsid fragments. Instead, we found a preponderance of 3 MDa complexes (90 subunits) and no fragments smaller than 3 MDa. We also found 90-mers in the disassembly of uncrosslinked HBV capsids. 90-mers seem to be a common pause point in disassembly reactions. Partly explaining this result, graph theory simulations have showed a threshold for capsid stability between 80 and 90 subunits. To test a molecular breadboard concept, we showed that missing subunits could be refilled resulting in chimeric, 120 subunit particles. This result may be a means of assembling unique capsids with functional decorations. © 2017 The Protein Society.

Superelastic Ball Bearings: Materials and Design to Avoid Mounting and Dismounting Brinell Damage in an Inaccessible Press-Fit Application-. I ; Design Approach

Science.gov (United States)

Dellacorte, Christopher; Howard, S. Adam

2015-01-01

Ball bearings require proper fit and installation into machinery structures (onto shafts and into bearing housings) to ensure optimal performance. For some applications, both the inner and outer race must be mounted with an interference fit and care must be taken during assembly and disassembly to avoid placing heavy static loads between the balls and races otherwise Brinell dent type damage can occur. In this paper, a highly dent resistant superelastic alloy, 60NiTi, is considered for rolling element bearing applications that encounter excessive static axial loading during assembly or disassembly. A small (R8) ball bearing is designed for an application in which access to the bearing races to apply disassembly tools is precluded. First Principles analyses show that by careful selection of materials, raceway curvature and land geometry, a bearing can be designed that allows blind assembly and disassembly without incurring raceway damage due to ball denting. Though such blind assembly applications are uncommon, the availability of bearings with unusually high static load capability may enable more such applications with additional benefits, especially for miniature bearings.

Observing dynamics of chromatin fibers in Xenopus egg extracts by single DNA manipulation using a transverse magnetic tweezer setup

Science.gov (United States)

Yan, Jie; Skoko, Dunja; Marko, John; Maresca, Tom; Heald, Rebecca

2005-03-01

We have studied assembly of chromatin on single DNAs using Xenopus egg extracts and a specially designed magnetic tweezer setup which generates controlled force in the focal plane of the objective, allowing us to visualize and measure DNA extension under a wide range of constant tensions. We found, in the absence of ATP, interphase extracts assembled nucleosomes against DNA tensions of up to 3.5 piconewtons (pN). We observed force-induced disassembly and opening-closing fluctuations indicating our experiments were in mechano-chemical equilibrium. We found that the ATP-depleted reaction can do mechanical work of 27 kcal/mol per nucleosome, providing a measurement of the free energy difference between core histone octamers on and off DNA. Addition of ATP leads to highly dynamic behavior: time courses show processive runs of assembly and disassembly of not observed in the -ATP case, with forces of 2 pN leading to nearly complete fiber disassembly. Our study shows that ATP hydrolysis plays a major role in nucleosome rearrangement and removal, and suggests that chromatin in vivo may be subject to continual assembly and disassembly.

Core Mediator structure at 3.4 Å extends model of transcription initiation complex.

Science.gov (United States)

Nozawa, Kayo; Schneider, Thomas R; Cramer, Patrick

2017-05-11

Mediator is a multiprotein co-activator that binds the transcription pre-initiation complex (PIC) and regulates RNA polymerase (Pol) II. The Mediator head and middle modules form the essential core Mediator (cMed), whereas the tail and kinase modules play regulatory roles. The architecture of Mediator and its position on the PIC are known, but atomic details are limited to Mediator subcomplexes. Here we report the crystal structure of the 15-subunit cMed from Schizosaccharomyces pombe at 3.4 Å resolution. The structure shows an unaltered head module, and reveals the intricate middle module, which we show is globally required for transcription. Sites of known Mediator mutations cluster at the interface between the head and middle modules, and in terminal regions of the head subunits Med6 (ref. 16) and Med17 (ref. 17) that tether the middle module. The structure led to a model for Saccharomyces cerevisiae cMed that could be combined with the 3.6 Å cryo-electron microscopy structure of the core PIC (cPIC). The resulting atomic model of the cPIC-cMed complex informs on interactions of the submodules forming the middle module, called beam, knob, plank, connector, and hook. The hook is flexibly linked to Mediator by a conserved hinge and contacts the transcription initiation factor IIH (TFIIH) kinase that phosphorylates the carboxy (C)-terminal domain (CTD) of Pol II and was recently positioned on the PIC. The hook also contains residues that crosslink to the CTD and reside in a previously described cradle. These results provide a framework for understanding Mediator function, including its role in stimulating CTD phosphorylation by TFIIH.

Persistence of Repair Proteins at Unrepaired DNA Damage Distinguishes Diseases with ERCC2 (XPD) Mutations: Cancer-Prone Xeroderma Pigmentosum vs. Non-Cancer-Prone Trichothiodystrophy

Science.gov (United States)

Boyle, Jennifer; Ueda, Takahiro; Oh, Kyu-Seon; Imoto, Kyoko; Tamura, Deborah; Jagdeo, Jared; Khan, Sikandar G.; Nadem, Carine; DiGiovanna, John J.; Kraemer, Kenneth H.

2012-01-01

Patients with xeroderma pigmentosum (XP) have a 1,000-fold increase in ultraviolet (UV)-induced skin cancers while trichothiodystrophy (TTD) patients, despite mutations in the same genes, ERCC2 (XPD) or ERCC3 (XPB), are cancer-free. Unlike XP cells, TTD cells have a nearly normal rate of removal of UV-induced 6-4 photoproducts (6-4PP) in their DNA and low levels of the basal transcription factor, TFIIH. We examined seven XP, TTD, and XP/TTD complex patients and identified mutations in the XPD gene. We discovered large differences in nucleotide excision repair (NER) protein recruitment to sites of localized UV damage in TTD cells compared to XP or normal cells. XPC protein was rapidly localized in all cells. XPC was redistributed in TTD, and normal cells by 3 hr postirradiation, but remained localized in XP cells at 24-hr postirradiation. In XP cells recruitment of other NER proteins (XPB, XPD, XPG, XPA, and XPF) was also delayed and persisted at 24 hr (p < 0.001). In TTD cells with defects in the XPD, XPB, or GTF2H5 (TTDA) genes, in contrast, recruitment of these NER proteins was reduced compared to normals at early time points (p < 0.001) and remained low at 24 hr postirradiation. These data indicate that in XP persistence of NER proteins at sites of unrepaired DNA damage is associated with greatly increased skin cancer risk possibly by blockage of translesion DNA synthesis. In contrast, in TTD, low levels of unstable TFIIH proteins do not accumulate at sites of unrepaired photoproducts and may permit normal translesion DNA synthesis without increased skin cancer. PMID:18470933

SSC 17-meter dipole magnet DD000Z test results and investigation of coil failure: The report of the open-quotes Zclose quotes Committee

International Nuclear Information System (INIS)

Coombes, R.; Lundy, R.; Schneider, W.; Wanderer, P.

1988-03-01

Following the failure of the lower inner coil of magnet DD000Z on November 3, 1987, a committee was formed on November 11 and given the following charges: 'To review the events leading up to and including the failure of the coils of magnet DD000Z. The intent of the review will be to determine the cause of the failure and to make recommendations to reduce the likelihood of such failures in the future. Given the fact that this is the first long magnet to be disassembled, the committee may uncover leads which point to other opportunities for improvement. The committee should follow up on these leads. The committee should prepare a plan to serve as an initial guide for the disassembly and provide guidance as the disassembly progresses.' The committee held its first meeting at FNAL on 17 and 18 Nov to review the record of events leading up to the failure and to establish an initial disassembly procedure. This was followed by further meetings at FNAL, BNL, and CDG, leading to this final report. Committee activities included interviewing personnel who had been involved in the design, assembly and testing of DD000Z, reviewing all documents relating to the magnet and its failure, and participating in and providing guidance during the disassembly. The intention of the committee was to report factual findings, to consider well founded hypotheses, not to consider conjecture and to avoid speculation

Dynamics of myosin II organization into cortical contractile networks and fibers

Science.gov (United States)

Nie, Wei; Wei, Ming-Tzo; Ou-Yang, Daniel; Jedlicka, Sabrina; Vavylonis, Dimitrios

2014-03-01

The morphology of adhered cells critically depends on the formation of a contractile meshwork of parallel and cross-linked stress fibers along the contacting surface. The motor activity and mini-filament assembly of non-muscle myosin II is an important component of cell-level cytoskeletal remodeling during mechanosensing. To monitor the dynamics of myosin II, we used confocal microscopy to image cultured HeLa cells that stably express myosin regulatory light chain tagged with GFP (MRLC-GFP). MRLC-GFP was monitored in time-lapse movies at steady state and during the response of cells to varying concentrations of blebbistatin which disrupts actomyosin stress fibers. Using image correlation spectroscopy analysis, we quantified the kinetics of disassembly and reassembly of actomyosin networks and compared them to studies by other groups. This analysis suggested that the following processes contribute to the assembly of cortical actomyosin into fibers: random myosin mini-filament assembly and disassembly along the cortex; myosin mini-filament aligning and contraction; stabilization of cortical myosin upon increasing contractile tension. We developed simple numerical simulations that include those processes. The results of simulations of cells at steady state and in response to blebbistatin capture some of the main features observed in the experiments. This study provides a framework to help interpret how different cortical myosin remodeling kinetics may contribute to different cell shape and rigidity depending on substrate stiffness.

Improved and verification of fast reactor safety analysis techniques. Annual summary, March 1, 1975--February 29, 1976

International Nuclear Information System (INIS)

Jackson, J.F.; Bott, T.F.

1976-01-01

Analyses of the Kiwi-TNT and SNAPTRAN-2 experiments have been performed with the VENUS-II fast-reactor disassembly code. The results show that VENUS-II provides an adequate characterization of these experiments. As is the case for LMFBRs, the excursions were initially turned over by temperature feedback effects, with ultimate shutdown coming from core disassembly. The calculated fission energies agree with the experimental values to within about 50 percent for the Kiwi excursion and 10 percent for the SNAPTRAN-2 experiment. The results of the analyses are being evaluated to determine the reasons for the remaining differences. It appears that part of the difference observed in the Kiwi-TNT analysis could relate to not explicitly treating the heat-transfer from the beaded fuel (a problem not present in LMFBR calculations). Both analyses also have uncertainties associated with the new equation-of-state that had to be added to VENUS-II to allow treatment of the core materials not used in fast reactors. Finally, there are uncertainties in the temperature feedback coefficients being used. In general, the uncertainties associated with applying VENUS-II to LMFBR excursions should be even smaller than those encountered in these experimental comparisons. This is because the temperature (Doppler) coefficients and core material equations-of-state are better known, and the complications associated with heat transfer from the beaded fuel are not present

Evaluation of Hydroprocessed Renewable Diesel (HRD) Fuel in a Caterpillar Engine Using the 210 Hour TWV Cycle

Science.gov (United States)

2014-05-01

TERMS Hydroprocessed Renewable Diesel , Reference Diesel Fuel, C7, emissions, power, performance, deposition, ambient, desert, synthetic fuel injector ...the engine run-in, the engine was disassembled to determine injector nozzle tip deposits, and the piston crowns and engine combustion chamber deposits...removed from the test cell and disassembled to determine injector nozzle tip and piston crown and engine combustion chamber deposits. Post- test

Transport-diffusion comparisons for small core LMFBR disruptive accidents

International Nuclear Information System (INIS)

Tomlinson, E.T.

1977-11-01

A number of numerical experiments were performed to assess the validity of diffusion theory for calculating the reactivity state of various small core LMFBR disrupted geometries. The disrupted configurations correspond, in general, to various configurations predicted by SAS3A for transient undercooling (TUC) and transient overpower (TOP) accidents for homogeneous cores and to the ZPPR-7 configurations for heterogeneous core. In all TUC cases diffusion theory was shown to be inadequate for the calculation of reactivity changes during core disassembly

Supermassive Black Holes and Their Host Spheroids. I. Disassembling Galaxies

Science.gov (United States)

Savorgnan, G. A. D.; Graham, A. W.

2016-01-01

Several recent studies have performed galaxy decompositions to investigate correlations between the black hole mass and various properties of the host spheroid, but they have not converged on the same conclusions. This is because their models for the same galaxy were often significantly different and not consistent with each other in terms of fitted components. Using 3.6 μm Spitzer imagery, which is a superb tracer of the stellar mass (superior to the K band), we have performed state-of-the-art multicomponent decompositions for 66 galaxies with directly measured black hole masses. Our sample is the largest to date and, unlike previous studies, contains a large number (17) of spiral galaxies with low black hole masses. We paid careful attention to the image mosaicking, sky subtraction, and masking of contaminating sources. After a scrupulous inspection of the galaxy photometry (through isophotal analysis and unsharp masking) and—for the first time—2D kinematics, we were able to account for spheroids large-scale, intermediate-scale, and nuclear disks bars rings spiral arms halos extended or unresolved nuclear sources; and partially depleted cores. For each individual galaxy, we compared our best-fit model with previous studies, explained the discrepancies, and identified the optimal decomposition. Moreover, we have independently performed one-dimensional (1D) and two-dimensional (2D) decompositions and concluded that, at least when modeling large, nearby galaxies, 1D techniques have more advantages than 2D techniques. Finally, we developed a prescription to estimate the uncertainties on the 1D best-fit parameters for the 66 spheroids that takes into account systematic errors, unlike popular 2D codes that only consider statistical errors.

Studies of complex fragment emission in heavy ion reactions

International Nuclear Information System (INIS)

Charity, R.J.; Sobotka, L.G.

1991-01-01

This report discusses the following topics: High energy photon production in a HI collision; the mechanism for the disassembly of excited 16 O projectiles into four alpha particles; the disassembly of excited 28 Si projectiles; large pre-fission multiplicities from temperature; dependent friction and fission barriers; multiplicity correlations; molecular beam induced fusion; dwarf ball and wall; mini wall; and computer and local data acquisition systems

FACT, the Bur kinase pathway, and the histone co-repressor HirC have overlapping nucleosome-related roles in yeast transcription elongation.

Directory of Open Access Journals (Sweden)

Jennifer R Stevens

Full Text Available Gene transcription is constrained by the nucleosomal nature of chromosomal DNA. This nucleosomal barrier is modulated by FACT, a conserved histone-binding heterodimer. FACT mediates transcription-linked nucleosome disassembly and also nucleosome reassembly in the wake of the RNA polymerase II transcription complex, and in this way maintains the repression of 'cryptic' promoters found within some genes. Here we focus on a novel mutant version of the yeast FACT subunit Spt16 that supplies essential Spt16 activities but impairs transcription-linked nucleosome reassembly in dominant fashion. This Spt16 mutant protein also has genetic effects that are recessive, which we used to show that certain Spt16 activities collaborate with histone acetylation and the activities of a Bur-kinase/Spt4-Spt5/Paf1C pathway that facilitate transcription elongation. These collaborating activities were opposed by the actions of Rpd3S, a histone deacetylase that restores a repressive chromatin environment in a transcription-linked manner. Spt16 activity paralleling that of HirC, a co-repressor of histone gene expression, was also found to be opposed by Rpd3S. Our findings suggest that Spt16, the Bur/Spt4-Spt5/Paf1C pathway, and normal histone abundance and/or stoichiometry, in mutually cooperative fashion, facilitate nucleosome disassembly during transcription elongation. The recessive nature of these effects of the mutant Spt16 protein on transcription-linked nucleosome disassembly, contrasted to its dominant negative effect on transcription-linked nucleosome reassembly, indicate that mutant FACT harbouring the mutant Spt16 protein competes poorly with normal FACT at the stage of transcription-linked nucleosome disassembly, but effectively with normal FACT for transcription-linked nucleosome reassembly. This functional difference is consistent with the idea that FACT association with the transcription elongation complex depends on nucleosome disassembly, and that the

SUPERMASSIVE BLACK HOLES AND THEIR HOST SPHEROIDS. I. DISASSEMBLING GALAXIES

Energy Technology Data Exchange (ETDEWEB)

Savorgnan, G. A. D.; Graham, A. W., E-mail: gsavorgn@astro.swin.edu.au [Centre for Astrophysics and Supercomputing, Swinburne University of Technology, Hawthorn, Victoria 3122 (Australia)

2016-01-15

Several recent studies have performed galaxy decompositions to investigate correlations between the black hole mass and various properties of the host spheroid, but they have not converged on the same conclusions. This is because their models for the same galaxy were often significantly different and not consistent with each other in terms of fitted components. Using 3.6 μm Spitzer imagery, which is a superb tracer of the stellar mass (superior to the K band), we have performed state-of-the-art multicomponent decompositions for 66 galaxies with directly measured black hole masses. Our sample is the largest to date and, unlike previous studies, contains a large number (17) of spiral galaxies with low black hole masses. We paid careful attention to the image mosaicking, sky subtraction, and masking of contaminating sources. After a scrupulous inspection of the galaxy photometry (through isophotal analysis and unsharp masking) and—for the first time—2D kinematics, we were able to account for spheroids; large-scale, intermediate-scale, and nuclear disks; bars; rings; spiral arms; halos; extended or unresolved nuclear sources; and partially depleted cores. For each individual galaxy, we compared our best-fit model with previous studies, explained the discrepancies, and identified the optimal decomposition. Moreover, we have independently performed one-dimensional (1D) and two-dimensional (2D) decompositions and concluded that, at least when modeling large, nearby galaxies, 1D techniques have more advantages than 2D techniques. Finally, we developed a prescription to estimate the uncertainties on the 1D best-fit parameters for the 66 spheroids that takes into account systematic errors, unlike popular 2D codes that only consider statistical errors.

SUPERMASSIVE BLACK HOLES AND THEIR HOST SPHEROIDS. I. DISASSEMBLING GALAXIES

International Nuclear Information System (INIS)

Savorgnan, G. A. D.; Graham, A. W.

2016-01-01

Several recent studies have performed galaxy decompositions to investigate correlations between the black hole mass and various properties of the host spheroid, but they have not converged on the same conclusions. This is because their models for the same galaxy were often significantly different and not consistent with each other in terms of fitted components. Using 3.6 μm Spitzer imagery, which is a superb tracer of the stellar mass (superior to the K band), we have performed state-of-the-art multicomponent decompositions for 66 galaxies with directly measured black hole masses. Our sample is the largest to date and, unlike previous studies, contains a large number (17) of spiral galaxies with low black hole masses. We paid careful attention to the image mosaicking, sky subtraction, and masking of contaminating sources. After a scrupulous inspection of the galaxy photometry (through isophotal analysis and unsharp masking) and—for the first time—2D kinematics, we were able to account for spheroids; large-scale, intermediate-scale, and nuclear disks; bars; rings; spiral arms; halos; extended or unresolved nuclear sources; and partially depleted cores. For each individual galaxy, we compared our best-fit model with previous studies, explained the discrepancies, and identified the optimal decomposition. Moreover, we have independently performed one-dimensional (1D) and two-dimensional (2D) decompositions and concluded that, at least when modeling large, nearby galaxies, 1D techniques have more advantages than 2D techniques. Finally, we developed a prescription to estimate the uncertainties on the 1D best-fit parameters for the 66 spheroids that takes into account systematic errors, unlike popular 2D codes that only consider statistical errors

Selective recruitment of nuclear factors to productively replicating herpes simplex virus genomes.

Science.gov (United States)

Dembowski, Jill A; DeLuca, Neal A

2015-05-01

Much of the HSV-1 life cycle is carried out in the cell nucleus, including the expression, replication, repair, and packaging of viral genomes. Viral proteins, as well as cellular factors, play essential roles in these processes. Isolation of proteins on nascent DNA (iPOND) was developed to label and purify cellular replication forks. We adapted aspects of this method to label viral genomes to both image, and purify replicating HSV-1 genomes for the identification of associated proteins. Many viral and cellular factors were enriched on viral genomes, including factors that mediate DNA replication, repair, chromatin remodeling, transcription, and RNA processing. As infection proceeded, packaging and structural components were enriched to a greater extent. Among the more abundant proteins that copurified with genomes were the viral transcription factor ICP4 and the replication protein ICP8. Furthermore, all seven viral replication proteins were enriched on viral genomes, along with cellular PCNA and topoisomerases, while other cellular replication proteins were not detected. The chromatin-remodeling complexes present on viral genomes included the INO80, SWI/SNF, NURD, and FACT complexes, which may prevent chromatinization of the genome. Consistent with this conclusion, histones were not readily recovered with purified viral genomes, and imaging studies revealed an underrepresentation of histones on viral genomes. RNA polymerase II, the mediator complex, TFIID, TFIIH, and several other transcriptional activators and repressors were also affinity purified with viral DNA. The presence of INO80, NURD, SWI/SNF, mediator, TFIID, and TFIIH components is consistent with previous studies in which these complexes copurified with ICP4. Therefore, ICP4 is likely involved in the recruitment of these key cellular chromatin remodeling and transcription factors to viral genomes. Taken together, iPOND is a valuable method for the study of viral genome dynamics during infection and

Coordinating repair of oxidative DNA damage with transcription and replication

International Nuclear Information System (INIS)

Cooper, P.K.

2003-01-01

Transcription-coupled repair (TCR) preferentially removes DNA lesions from template strands of active genes. Defects in TCR, which acts both on lesions removed by nucleotide excision repair (NER) and on oxidative lesions removed by base excision repair (BER), underlie the fatal developmental disorder Cockayne syndrome. Although its detailed mechanism remains unknown, TCR involves recognition of a stalled RNA polymerase (RNAP), removal or remodeling of RNAP to allow access to the lesion, and recruitment of repair enzymes. At a minimum, these early steps require a non-enzymatic function of the multifunctional repair protein XPG, the CSB protein with ATP-dependent chromatin remodeling activity, and the TFIIH complex (including the XPB and XPD helicases) that is also required for basal transcription initiation and NER. XPG exists in the cell in a complex with TFIIH, and in vitro evidence has suggested that it interacts with CSB. To address the mechanism of TCR, we are characterizing protein-DNA and protein-protein interactions of XPG. We show that XPG preferentially binds to double-stranded DNA containing bubbles resembling in size the unpaired regions associated with transcription. Two distinct domains of XPG are required for the observed strong binding specificity and stability. XPG both interacts directly with CSB and synergistically binds with it to bubble DNA, and it strongly stimulates the bubble DNA-dependent ATPase activity of CSB. Significantly for TCR, XPG also interacts directly with RNAP II, binds both the protein and nucleic acid components (the R-loop) of a stalled RNA polymerase, and forms a ternary complex with CSB and the stalled RNAP. These results are consistent with the model that XPG and CSB jointly interact with the DNA/chromatin structure in the vicinity of the stalled transcriptional apparatus and with the transcriptional machinery itself to remodel the chromatin and either move or remodel the blocked RNA polymerase to expose the lesion

Post-test analysis of lithium-ion battery materials at Argonne National Laboratory

Science.gov (United States)

Bareno, Javier; Dietz-Rago, Nancy; Bloom, Ira

2014-03-01

Electrochemical performance is often limited by surface and interfacial reactions at the electrodes. However, routine handling of samples can alter the very surfaces that are the object of study. Our approach combines standardized testing of batteries with sample harvesting under inert atmosphere conditions. Cells of different formats are disassembled inside an Argon glove box with controlled water and oxygen concentrations below 2 ppm. Cell components are characterized in situ, guaranteeing that observed changes in physicochemical state are due to electrochemical operation, rather than sample manipulation. We employ a complementary set of spectroscopic, microscopic, electrochemical and metallographic characterization to obtain a complete picture of cell degradation mechanisms. The resulting information about observed degradation mechanisms is provided to materials developers, both academic and industrial, to suggest new strategies and speed up the Research & Development cycle of Li-ion and related technologies. This talk will describe Argonne's post-test analysis laboratory, with an emphasis on capabilities and opportunities for collaboration. Cell disassembly, sample harvesting procedures and recent results will be discussed. This work was performed under the auspices of the U.S. Department of Energy, Office of Vehicle Technologies, Hybrid and Electric Systems, under Contract No. DE-AC02-06CH11357.

Chd1 remodelers maintain open chromatin and regulate the epigenetics of differentiation

Energy Technology Data Exchange (ETDEWEB)

Persson, Jenna [Department of Biosciences and Nutrition, Center for Biosciences, Karolinska Institutet (Sweden); Ekwall, Karl, E-mail: karl.ekwall@ki.se [Department of Biosciences and Nutrition, Center for Biosciences, Karolinska Institutet (Sweden); School of Life Sciences, University College Sodertorn, NOVUM, Huddinge (Sweden)

2010-05-01

Eukaryotic DNA is packaged around octamers of histone proteins into nucleosomes, the basic unit of chromatin. In addition to enabling meters of DNA to fit within the confines of a nucleus, the structure of chromatin has functional implications for cell identity. Covalent chemical modifications to the DNA and to histones, histone variants, ATP-dependent chromatin remodelers, small noncoding RNAs and the level of chromatin compaction all contribute to chromosomal structure and to the activity or silencing of genes. These chromatin-level alterations are defined as epigenetic when they are heritable from mother to daughter cell. The great diversity of epigenomes that can arise from a single genome permits a single, totipotent cell to generate the hundreds of distinct cell types found in humans. Two recent studies in mouse and in fly have highlighted the importance of Chd1 chromatin remodelers for maintaining an open, active chromatin state. Based on evidence from fission yeast as a model system, we speculate that Chd1 remodelers are involved in the disassembly of nucleosomes at promoter regions, thus promoting active transcription and open chromatin. It is likely that these nucleosomes are specifically marked for disassembly by the histone variant H2A.Z.

Chd1 remodelers maintain open chromatin and regulate the epigenetics of differentiation

International Nuclear Information System (INIS)

Persson, Jenna; Ekwall, Karl

2010-01-01

Eukaryotic DNA is packaged around octamers of histone proteins into nucleosomes, the basic unit of chromatin. In addition to enabling meters of DNA to fit within the confines of a nucleus, the structure of chromatin has functional implications for cell identity. Covalent chemical modifications to the DNA and to histones, histone variants, ATP-dependent chromatin remodelers, small noncoding RNAs and the level of chromatin compaction all contribute to chromosomal structure and to the activity or silencing of genes. These chromatin-level alterations are defined as epigenetic when they are heritable from mother to daughter cell. The great diversity of epigenomes that can arise from a single genome permits a single, totipotent cell to generate the hundreds of distinct cell types found in humans. Two recent studies in mouse and in fly have highlighted the importance of Chd1 chromatin remodelers for maintaining an open, active chromatin state. Based on evidence from fission yeast as a model system, we speculate that Chd1 remodelers are involved in the disassembly of nucleosomes at promoter regions, thus promoting active transcription and open chromatin. It is likely that these nucleosomes are specifically marked for disassembly by the histone variant H2A.Z.

An Efficient Procedure for Removal and Inactivation of Alpha-Synuclein Assemblies from Laboratory Materials.

Science.gov (United States)

Bousset, Luc; Brundin, Patrik; Böckmann, Anja; Meier, Beat; Melki, Ronald

2016-01-01

Preformed α-synuclein fibrils seed the aggregation of soluble α-synuclein in cultured cells and in vivo. This, and other findings, has kindled the idea that α-synuclein fibrils possess prion-like properties. As α-synuclein fibrils should not be considered as innocuous, there is a need for decontamination and inactivation procedures for laboratory benches and non-disposable laboratory material. We assessed the effectiveness of different procedures designed to disassemble α-synuclein fibrils and reduce their infectivity. We examined different commercially available detergents to remove α-synuclein assemblies adsorbed on materials that are not disposable and that are most found in laboratories (e.g. plastic, glass, aluminum or stainless steel surfaces). We show that methods designed to decrease PrP prion infectivity neither effectively remove α-synuclein assemblies adsorbed to different materials commonly used in the laboratory nor disassemble the fibrillar form of the protein with efficiency. In contrast, both commercial detergents and SDS detached α-synuclein assemblies from contaminated surfaces and disassembled the fibrils. We describe three cleaning procedures that effectively remove and disassemble α-synuclein seeds. The methods rely on the use of detergents that are compatible with most non-disposable tools in a laboratory. The procedures are easy to implement and significantly decrease any potential risks associated to handling α-synuclein assemblies.

Mechanisms of DNA replication termination.

Science.gov (United States)

Dewar, James M; Walter, Johannes C

2017-08-01

Genome duplication is carried out by pairs of replication forks that assemble at origins of replication and then move in opposite directions. DNA replication ends when converging replication forks meet. During this process, which is known as replication termination, DNA synthesis is completed, the replication machinery is disassembled and daughter molecules are resolved. In this Review, we outline the steps that are likely to be common to replication termination in most organisms, namely, fork convergence, synthesis completion, replisome disassembly and decatenation. We briefly review the mechanism of termination in the bacterium Escherichia coli and in simian virus 40 (SV40) and also focus on recent advances in eukaryotic replication termination. In particular, we discuss the recently discovered E3 ubiquitin ligases that control replisome disassembly in yeast and higher eukaryotes, and how their activity is regulated to avoid genome instability.

Cdk1 and Okadaic Acid-sensitive Phosphatases Control Assembly of Nuclear Pore Complexes in Drosophila EmbryosV⃞

OpenAIRE

Onischenko, Evgeny A.; Gubanova, Natalia V.; Kiseleva, Elena V.; Hallberg, Einar

2005-01-01

Disassembly and reassembly of the nuclear pore complexes (NPCs) is one of the major events during open mitosis in higher eukaryotes. However, how this process is controlled by the mitotic machinery is not clear. To investigate this we developed a novel in vivo model system based on syncytial Drosophila embryos. We microinjected different mitotic effectors into the embryonic cytoplasm and monitored the dynamics of disassembly/reassembly of NPCs in live embryos using fluorescently labeled wheat...

The dynamics of the nuclear disassembly in a field-theoretical model at finite entropies

International Nuclear Information System (INIS)

Knoll, J.; Strack, B.

1984-10-01

The expansion phase of a hot nuclear system as created in an energetic heavy-ion collision is calculated and discussed by a selfconsistent field-theoretical model. Dynamical instabilities arising during the expansion from strong fluctuations of the one-body density are included explicitely. First multiplicity distributions and mass spectra resulting from a series of numerical runs in a 2+1 dimensional model world are presented. The dependence of break-up dynamics both on the properties of the binding force and possible correlations in the initially compressed hot state are discussed. (orig.)

The calcium-modulated proteins, S100A1 and S100B, as potential regulators of the dynamics of type III intermediate filaments

Directory of Open Access Journals (Sweden)

M. Garbuglia

1999-10-01

Full Text Available The Ca2+-modulated, dimeric proteins of the EF-hand (helix-loop-helix type, S100A1 and S100B, that have been shown to inhibit microtubule (MT protein assembly and to promote MT disassembly, interact with the type III intermediate filament (IF subunits, desmin and glial fibrillary acidic protein (GFAP, with a stoichiometry of 2 mol of IF subunit/mol of S100A1 or S100B dimer and an affinity of 0.5-1.0 µM in the presence of a few micromolar concentrations of Ca2+. Binding of S100A1 and S100B results in inhibition of desmin and GFAP assemblies into IFs and stimulation of the disassembly of preformed desmin and GFAP IFs. S100A1 and S100B interact with a stretch of residues in the N-terminal (head domain of desmin and GFAP, thereby blocking the head-to-tail process of IF elongation. The C-terminal extension of S100A1 (and, likely, S100B represents a critical part of the site that recognizes desmin and GFAP. S100B is localized to IFs within cells, suggesting that it might have a role in remodeling IFs upon elevation of cytosolic Ca2+ concentration by avoiding excess IF assembly and/or promoting IF disassembly in vivo. S100A1, that is not localized to IFs, might also play a role in the regulation of IF dynamics by binding to and sequestering unassembled IF subunits. Together, these observations suggest that S100A1 and S100B may be regarded as Ca2+-dependent regulators of the state of assembly of two important elements of the cytoskeleton, IFs and MTs, and, potentially, of MT- and IF-based activities.

Spent Fuel Handling and Packaging Program: a survey of hot cell facilities

International Nuclear Information System (INIS)

Menon, M.N.

1978-07-01

Hot cell facilities in the United States were surveyed to determine their capabilities for conducting integral fuel assembly and individual fuel rod examinations that are required in support of the Spent Fuel Handling and Packaging Program. The ability to receive, handle, disassemble and reconstitute full-length light water reactor spent fuel assemblies, and the ability to conduct nondestructive and destructive examinations on full-length fuel rods were of particular interest. Three DOE-supported facilities and three commercial facilities were included in the survey. This report provides a summary of the findings

A contribuição da análise ergonômica ao projeto do produto voltado para a reciclagem The ergonomics analysis contribution for the product project directed to wards recycling

Directory of Open Access Journals (Sweden)

Rose Mary Rosa de Lima

2003-01-01

Full Text Available Este artigo apresenta uma análise da desmontagem manual para a reciclagem do produto. A Análise Ergonômica da Atividade dos recicladores é utilizada como uma ferramenta de apoio ao Projeto para Meio Ambiente,através da avaliação das dificuldades na desmontagem do produto. Do ponto de vista econômico, a desmontagem do produto deve ser executada com um custo mínimo, para viabilizar a reciclagem que, atendendo às exigências das indústrias, inclui atividades bastante complexas para separação dos componentes. Estas estratégias de desmontagem e as condições de trabalho dos envolvidos nestes processos podem ser levadas em consideração nas fases iniciais do projeto do produto, o que traria benefícios aos recicladores, às indústrias e, em última análise, ao próprio meio ambiente. O estudo de caso foi realizado na Associação de Catadores de Papel, Papelão e Materiais Reaproveitáveis (ASMARE e teve como foco a análise da desmontagem da embalagem Politereftalato de Etileno (Pet. O estudo demonstra que a análise das dificuldades derivadas da atividade da desmontagem do produto fornece meios para identificar as características do produto, definidas em projeto, que interferem na desmontagem.This paper presents an analysis of the manual disassembly for product recycling. The Ergonomics Activity Analysis of the recyclers is used as a tool of support to the Design for Environment, through the evaluation of the disassembly difficulty of the product. Of the economic point of view, the disassembly of the product must be executed with a minimum cost, to make possible the recycling that, taking care of to the requirements of the industries, includes sufficiently complex activities for separation of the components. These strategies of disassembly and the conditions of work of the involved ones in these processes can be taken in consideration in the initial phases of the design product, what it would bring benefits to the recyclers, the

Disassembling archeology, reassembling the modern world.

Science.gov (United States)

Carruthers, William; Van Damme, Stéphane

2017-09-01

This article provides a substantive discussion of the relevance of the history of archeology to the history of science. At the same time, the article introduces the papers contained in this special issue as exemplars of this relevance. To make its case, the article moves through various themes in the history of archeology that overlap with key issues in the history of science. The article discusses the role and tension of regimes of science in antiquarian and archeological practices, and also considers issues of scale and place, particularly in relation to the field. Additionally, the piece attends to issues of professionalization and the constitution of an archeological public, at the same time as discussing issues of empire, colonialism, and the circulation of knowledge. Meanwhile, enriching discussions within and beyond the history of science, the article discusses the history of archeology and its relationship with museums, collecting, and material culture and materiality. Finally, the piece discusses the relationship of the history of archeology with wider discussions about scientific ethics. In conclusion, the article questions whether we should speak of 'the history of archeology' at all.

Termination of DNA replication forks: "Breaking up is hard to do".

Science.gov (United States)

Bailey, Rachael; Priego Moreno, Sara; Gambus, Agnieszka

2015-01-01

To ensure duplication of the entire genome, eukaryotic DNA replication initiates from thousands of replication origins. The replication forks move through the chromatin until they encounter forks from neighboring origins. During replication fork termination forks converge, the replisomes disassemble and topoisomerase II resolves the daughter DNA molecules. If not resolved efficiently, terminating forks result in genomic instability through the formation of pathogenic structures. Our recent findings shed light onto the mechanism of replisome disassembly upon replication fork termination. We have shown that termination-specific polyubiquitylation of the replicative helicase component - Mcm7, leads to dissolution of the active helicase in a process dependent on the p97/VCP/Cdc48 segregase. The inhibition of terminating helicase disassembly resulted in a replication termination defect. In this extended view we present hypothetical models of replication fork termination and discuss remaining and emerging questions in the DNA replication termination field.

Assessment of end-of-life design in solid-state lighting

Science.gov (United States)

Dzombak, Rachel; Padon, Jack; Salsbury, Josh; Dillon, Heather

2017-08-01

Consumers in the US market and across the globe are beginning to widely adopt light emitting diode (LED) lighting products while the technology continues to undergo significant changes. While LED products are evolving to consume less energy, they are also more complex than traditional lighting products with a higher number of parts and a larger number of electronic components. Enthusiasm around the efficiency and long expected life span of LED lighting products is valid, but research to optimize product characteristics and design is needed. This study seeks to address that gap by characterizing LED lighting products' suitability for end of life (EOL) recycling and disposal. The authors disassembled and assessed 17 different lighting products to understand how designs differ between brands and manufacture year. Products were evaluated based on six parameters to quantify the design. The analysis indicates that while the efficiency of LED products has improved dramatically in the recent past, product designers and manufacturers could incorporate design strategies to improve environmental performance of lighting products at end-of-life.

Insight the C-site pocket conformational changes responsible for sirtuin 2 activity using molecular dynamics simulations.

Directory of Open Access Journals (Sweden)

Sugunadevi Sakkiah

Full Text Available Sirtuin belongs to a family of typical histone deacetylase which regulates the fundamental cellular biological processes including gene expression, genome stability, mitosis, nutrient metabolism, aging, mitochondrial function, and cell motility. Michael et. al. reported that B-site mutation (Q167A and H187A decreased the SIRT2 activity but still the structural changes were not reported. Hence, we performed 5 ns molecular dynamics (MD simulation on SIRT2 Apo-form and complexes with substrate/NAD(+ and inhibitor of wild type (WT, Q167A, and H187A. The results revealed that the assembly and disassembly of C-site induced by presence of substrate/NAD(+ and inhibitor, respectively. This assembly and disassembly was mainly due to the interaction between the substrate/NAD(+ and inhibitor and F96 and the distance between F96 and H187 which are present at the neck of the C-site. MD simulations suggest that the conformational change of L3 plays a major role in assembly and disassembly of C-site. Our current results strongly suggest that the distinct conformational change of L3 as well as the assembly and disassembly of C-site plays an important role in SIRT2 deacetylation function. Our study unveiled the structural changes of SIRT2 in presence of NAD(+ and inhibitor which should be helpful to improve the inhibitory potency of SIRT2.

Progress Report on Disassembly and Post-Irradiation Experiments for UCSB ATR-2 Experiment

Energy Technology Data Exchange (ETDEWEB)

Nanstad, Randy K [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Odette, G. R. [Univ. of California, Santa Barbara, CA (United States); Robertson, Janet Pawel [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yamamoto, T [Univ. of California, Santa Barbara, CA (United States)

2015-09-01

The reactor pressure vessel (RPV) in a light-water reactor (LWR) represents the first line of defense against a release of radiation in case of an accident. Thus, regulations that govern the operation of commercial nuclear power plants require conservative margins of fracture toughness, both during normal operation and under accident scenarios. In the unirradiated condition, the RPV has sufficient fracture toughness such that failure is implausible under any postulated condition, including pressurized thermal shock (PTS) in pressurized water reactors (PWR). In the irradiated condition, however, the fracture toughness of the RPV may be severely degraded, with the degree of toughness loss dependent on the radiation sensitivity of the materials. As stated in previous progress reports, the available embrittlement predictive models, e.g. [1], and our present understanding of radiation damage are not fully quantitative, and do not treat all potentially significant variables and issues, particularly considering extension of operation to 80y.

NAD+ and SIRT3 control microtubule dynamics and reduce susceptibility to antimicrotubule agents

Science.gov (United States)

Harkcom, William T.; Ghosh, Ananda K.; Sung, Matthew S.; Matov, Alexandre; Brown, Kevin D.; Giannakakou, Paraskevi; Jaffrey, Samie R.

2014-01-01

Nicotinamide adenine dinucleotide (NAD+) is an endogenous enzyme cofactor and cosubstrate that has effects on diverse cellular and physiologic processes, including reactive oxygen species generation, mitochondrial function, apoptosis, and axonal degeneration. A major goal is to identify the NAD+-regulated cellular pathways that may mediate these effects. Here we show that the dynamic assembly and disassembly of microtubules is markedly altered by NAD+. Furthermore, we show that the disassembly of microtubule polymers elicited by microtubule depolymerizing agents is blocked by increasing intracellular NAD+ levels. We find that these effects of NAD+ are mediated by the activation of the mitochondrial sirtuin sirtuin-3 (SIRT3). Overexpression of SIRT3 prevents microtubule disassembly and apoptosis elicited by antimicrotubule agents and knockdown of SIRT3 prevents the protective effects of NAD+ on microtubule polymers. Taken together, these data demonstrate that NAD+ and SIRT3 regulate microtubule polymerization and the efficacy of antimicrotubule agents. PMID:24889606

beta2-adaptin is constitutively de-phosphorylated by serine/threonine protein phosphatase PP2A and phosphorylated by a staurosporine-sensitive kinase

DEFF Research Database (Denmark)

Lauritsen, Jens Peter Holst; Menné, C; Kastrup, J

2000-01-01

Clathrin-mediated endocytosis includes cycles of assembly and disassembly of the clathrin-coated vesicle constituents. How these cycles are regulated is still not fully known but previous studies have indicated that phosphorylation of coat subunits may play a role. Here we describe that beta2-ada...... the hypothesis that phosphorylation/de-phosphorylation of coat proteins plays a regulatory role in the assembly/disassembly cycle of clathrin-coated vesicles.......Clathrin-mediated endocytosis includes cycles of assembly and disassembly of the clathrin-coated vesicle constituents. How these cycles are regulated is still not fully known but previous studies have indicated that phosphorylation of coat subunits may play a role. Here we describe that beta2......-adaptin undergoes cycles of phosphorylation/de-phosphorylation in intact cells. Thus, beta2-adaptin was constitutively de-phosphorylated by serine/threonine protein phosphatase 2A and phosphorylated by a staurosporine-sensitive kinase in vivo. Confocal laser scanning microscopy demonstrated...

Assembly mechanism for nuclear fuel bundles

International Nuclear Information System (INIS)

Long, J.W.; Flora, B.S.

1977-01-01

A method of securing a fuel bundle to permit easy remote disassembly is described. Fuel rods are held loosely between end plates, each end of the rods fitting into holes in the end plates. At the upper end of each fuel rod there is a spring pressing against the end plate. Tie rods are used to hold the end plates together securely. The lower end of each tie rod is screwed into the lower end plate; the upper end of each tie rod is attached to the upper end plate by means of a locking assembly described in the patent. In order to remove the upper tie plate during the disassembly process, it is necessary only to depress the tie plate against the pressure of the springs surrounding the fuel rods and then to rotate each locking sleeve on the tie rods from its locked to its unlocked position. It is then possible to remove the tie plate without disassembling the locking assembly. (LL)

Dynamics of myosin II organization into contractile networks and fibers at the medial cell cortex

Science.gov (United States)

Nie, Wei

The cellular morphology of adhered cells depends crucially on the formation of a contractile meshwork of parallel and cross-linked stress fibers along the contacting surface. The motor activity and mini-filament assembly of non-muscle myosin II is an important component of cell-level cytoskeletal remodeling during mechanosensing. To monitor the dynamics of non-muscle myosin II, we used confocal microscopy to image cultured HeLa cells that stably express myosin regulatory light chain tagged with GFP (MRLC-GFP). MRLC-GFP was monitored in time-lapse movies at steady state and during the response of cells to varying concentrations of blebbistatin (which disrupts actomyosin stress fibers). Using image correlation spectroscopy analysis, we quantified the kinetics of disassembly and reassembly of actomyosin networks and compared to studies by other groups. This analysis suggested the following processes: myosin minifilament assembly and disassembly; aligning and contraction; myosin filament stabilization upon increasing contractile tension. Numerical simulations that include those processes capture some of the main features observed in the experiments. This study provides a framework to help interpret how different cortical myosin remodeling kinetics may contribute to different cell shape and rigidity depending on substrate stiffness. We discuss methods to monitor myosin reorganization using non-linear imaging methods.

Glycolytic control of vacuolar-type ATPase activity: A mechanism to regulate influenza viral infection

Energy Technology Data Exchange (ETDEWEB)

Kohio, Hinissan P.; Adamson, Amy L., E-mail: aladamso@uncg.edu

2013-09-15

As new influenza virus strains emerge, finding new mechanisms to control infection is imperative. In this study, we found that we could control influenza infection of mammalian cells by altering the level of glucose given to cells. Higher glucose concentrations induced a dose-specific increase in influenza infection. Linking influenza virus infection with glycolysis, we found that viral replication was significantly reduced after cells were treated with glycolytic inhibitors. Addition of extracellular ATP after glycolytic inhibition restored influenza infection. We also determined that higher levels of glucose promoted the assembly of the vacuolar-type ATPase within cells, and increased vacuolar-type ATPase proton-transport activity. The increase of viral infection via high glucose levels could be reversed by inhibition of the proton pump, linking glucose metabolism, vacuolar-type ATPase activity, and influenza viral infection. Taken together, we propose that altering glucose metabolism may be a potential new approach to inhibit influenza viral infection. - Highlights: • Increased glucose levels increase Influenza A viral infection of MDCK cells. • Inhibition of the glycolytic enzyme hexokinase inhibited Influenza A viral infection. • Inhibition of hexokinase induced disassembly the V-ATPase. • Disassembly of the V-ATPase and Influenza A infection was bypassed with ATP. • The state of V-ATPase assembly correlated with Influenza A infection of cells.

Glycolytic control of vacuolar-type ATPase activity: A mechanism to regulate influenza viral infection

International Nuclear Information System (INIS)

Kohio, Hinissan P.; Adamson, Amy L.

2013-01-01

As new influenza virus strains emerge, finding new mechanisms to control infection is imperative. In this study, we found that we could control influenza infection of mammalian cells by altering the level of glucose given to cells. Higher glucose concentrations induced a dose-specific increase in influenza infection. Linking influenza virus infection with glycolysis, we found that viral replication was significantly reduced after cells were treated with glycolytic inhibitors. Addition of extracellular ATP after glycolytic inhibition restored influenza infection. We also determined that higher levels of glucose promoted the assembly of the vacuolar-type ATPase within cells, and increased vacuolar-type ATPase proton-transport activity. The increase of viral infection via high glucose levels could be reversed by inhibition of the proton pump, linking glucose metabolism, vacuolar-type ATPase activity, and influenza viral infection. Taken together, we propose that altering glucose metabolism may be a potential new approach to inhibit influenza viral infection. - Highlights: • Increased glucose levels increase Influenza A viral infection of MDCK cells. • Inhibition of the glycolytic enzyme hexokinase inhibited Influenza A viral infection. • Inhibition of hexokinase induced disassembly the V-ATPase. • Disassembly of the V-ATPase and Influenza A infection was bypassed with ATP. • The state of V-ATPase assembly correlated with Influenza A infection of cells

Investigation of axial positioning for flexural compressors

Science.gov (United States)

Riggle, Peter

1991-01-01

The testing of the research compressor is presented. The research compressor was assembled and disassembled in order to show the consistency in which the piston and rod could be aligned with a .0004 inch radial gap around the piston. A full set of tests was completed for the first assembly, which is referred to as assembly no. 1. The compressor was disassembled and assembled a second time (assembly no. 2). Assembly no. 2 was only tested statically due to the time constraint. Results are discussed.

Exclusive observables from a statistical simulation of energetic nuclear collisions

International Nuclear Information System (INIS)

Fai, G.

1983-01-01

Exclusive observables are calculated in the framework of a statistical model for medium-energy nuclear collisions. The collision system is divided into a few (participant/spectator) sources, that are assumed to disassemble independently. Sufficiently excited sources explode into pions, nucleons, and composite, possibly particle unstable, nuclei. The different final states compete according to their microcanonical weight. Less excited sources, and the unstable explosion products, deexcite via light-particle evaporation. The model has been implemented as a Monte Carlo computer code that is sufficiently efficient to permit generation of large event samples. Some illustrative applications are discussed. (author)

Sticking together: building a biofilm the Bacillus subtilis way

Science.gov (United States)

Vlamakis, Hera; Chai, Yunrong; Beauregard, Pascale; Losick, Richard; Kolter, Roberto

2014-01-01

Preface Biofilms are ubiquitous communities of tightly associated bacteria encased in an extracellular matrix. Bacillus subtilis has long-served as a robust model organism to examine the molecular mechanisms of biofilm formation and a number of studies have revealed that this process is subject to a number of integrated regulatory pathways. In this Review, we focus on the molecular mechanisms controlling biofilm assembly and briefly summarize the current state of knowledge regarding their disassembly. We also discuss recent progress that has expanded our understanding of biofilm formation on plant roots, which are a natural habitat for this soil bacterium. PMID:23353768

Sticking together: building a biofilm the Bacillus subtilis way.

Science.gov (United States)

Vlamakis, Hera; Chai, Yunrong; Beauregard, Pascale; Losick, Richard; Kolter, Roberto

2013-03-01

Biofilms are ubiquitous communities of tightly associated bacteria encased in an extracellular matrix. Bacillus subtilis has long served as a robust model organism to examine the molecular mechanisms of biofilm formation, and a number of studies have revealed that this process is regulated by several integrated pathways. In this Review, we focus on the molecular mechanisms that control B. subtilis biofilm assembly, and then briefly summarize the current state of knowledge regarding biofilm disassembly. We also discuss recent progress that has expanded our understanding of B. subtilis biofilm formation on plant roots, which are a natural habitat for this soil bacterium.

The influence of the reactivity ramp on the course of the power transient in the MARK 1A core of the SNR 300

International Nuclear Information System (INIS)

Froehlich, R.; Schmuck, P.

1976-01-01

The course of a hypothetic transient overpower accident caused by the onset of a not further specified reactivity ramp accompanied by the simultaneous failure of both shutdown systems must be analyzed in the SNR 300 Mark 1A core licensing procedure. The present study is limited to the discussion of the starting and shutdown phases of such accidents for the fresh core. Depending on the operational state of the reactor, the core geometry is still intact during the starting phase. In the following shutdown phase (core disassembly phase), large-scale mass transfer leads to the nuclear shutdown of the reactor. (orig./AK) [de

Nuclear Zpif-type plots

International Nuclear Information System (INIS)

Ma Yugang

2000-01-01

Isospin dependent classical molecular dynamics model is used to investigate the nuclear disassembly of 129 Xe. Zpif-type plot in the field of linguistics is tested for the rank-classified cluster arrangement from this nuclear disassembly. It is found that the average cluster charge (or mass) of rank n in the charge (or mass) list is exactly inverse to its rank, i.e. there exists Zpif's law at the point of the liquid gas phase transition. This novel criterion can be used to diagnose the nuclear liquid gas phase transition experimentally and theoretically

Head-end reprocessing equipment remote maintenance demonstration

International Nuclear Information System (INIS)

Evans, J.H.; Metz, C.F. III.

1989-01-01

Prototype equipment for reprocessing breeder reactor nuclear fuel was installed in the Remote Operation and Maintenance Demonstration (ROMD) area of the Consolidated Fuel Reprocessing Program (CFRP) facility at the Oak Ridge National Laboratory (ORNL) in order to evaluate the design of this equipment in a cold mock-up of a remotely maintained hot cell. This equipment included the Remote Disassembly System (RDS) and the Remote Shear System (RSS). These systems were disassembled and reassembled remotely by using the extensive remote handling systems that are installed in this simulated hot-cell environment. 5 refs., 5 figs

Fuel assembly duct cutting in the FFTF/IEM Cell

International Nuclear Information System (INIS)

Gibbons, P.W.

1985-01-01

Two mill type slitting cutters are used in the Fast Flux Test Facility (FFTF) Interim Examination and Maintenance (IEM) Cell during the disassembly sequence of a Driver Fuel Assembly. This disassembly is necessary so that selected parts may be examined both in the IEM Cell and elsewhere. The cutters have been in use for two years. During this time eight Driver Fuel assemblies have been taken apart in the IEM Cell. The cutters' operating philosophy and characteristics, as well as lessons learned from a significant equipment failure are presented. 1 ref., 6 figs., 1 tab

Selective recruitment of nuclear factors to productively replicating herpes simplex virus genomes.

Directory of Open Access Journals (Sweden)

Jill A Dembowski

2015-05-01

Full Text Available Much of the HSV-1 life cycle is carried out in the cell nucleus, including the expression, replication, repair, and packaging of viral genomes. Viral proteins, as well as cellular factors, play essential roles in these processes. Isolation of proteins on nascent DNA (iPOND was developed to label and purify cellular replication forks. We adapted aspects of this method to label viral genomes to both image, and purify replicating HSV-1 genomes for the identification of associated proteins. Many viral and cellular factors were enriched on viral genomes, including factors that mediate DNA replication, repair, chromatin remodeling, transcription, and RNA processing. As infection proceeded, packaging and structural components were enriched to a greater extent. Among the more abundant proteins that copurified with genomes were the viral transcription factor ICP4 and the replication protein ICP8. Furthermore, all seven viral replication proteins were enriched on viral genomes, along with cellular PCNA and topoisomerases, while other cellular replication proteins were not detected. The chromatin-remodeling complexes present on viral genomes included the INO80, SWI/SNF, NURD, and FACT complexes, which may prevent chromatinization of the genome. Consistent with this conclusion, histones were not readily recovered with purified viral genomes, and imaging studies revealed an underrepresentation of histones on viral genomes. RNA polymerase II, the mediator complex, TFIID, TFIIH, and several other transcriptional activators and repressors were also affinity purified with viral DNA. The presence of INO80, NURD, SWI/SNF, mediator, TFIID, and TFIIH components is consistent with previous studies in which these complexes copurified with ICP4. Therefore, ICP4 is likely involved in the recruitment of these key cellular chromatin remodeling and transcription factors to viral genomes. Taken together, iPOND is a valuable method for the study of viral genome dynamics

Quantum entanglement and quantum teleportation

International Nuclear Information System (INIS)

Shih, Y.H.

2001-01-01

One of the most surprising consequences of quantum mechanics is the entanglement of two or more distance particles. The ''ghost'' interference and the ''ghost'' image experiments demonstrated the astonishing nonlocal behavior of an entangled photon pair. Even though we still have questions in regard to fundamental issues of the entangled quantum systems, quantum entanglement has started to play important roles in quantum information and quantum computation. Quantum teleportation is one of the hot topics. We have demonstrated a quantum teleportation experiment recently. The experimental results proved the working principle of irreversibly teleporting an unknown arbitrary quantum state from one system to another distant system by disassembling into and then later reconstructing from purely classical information and nonclassical EPR correlations. The distinct feature of this experiment is that the complete set of Bell states can be distinguished in the Bell state measurement. Teleportation of a quantum state can thus occur with certainty in principle. (orig.)

Induced Förster resonance energy transfer by encapsulation of DNA-scaffold based probes inside a plant virus based protein cage

Science.gov (United States)

de Ruiter, Mark V.; Overeem, Nico J.; Singhai, Gaurav; Cornelissen, Jeroen J. L. M.

2018-05-01

Insight into the assembly and disassembly of viruses can play a crucial role in developing cures for viral diseases. Specialized fluorescent probes can benefit the study of interactions within viruses, especially during cell studies. In this work, we developed a strategy based on Förster resonance energy transfer (FRET) to study the assembly of viruses without labeling the exterior of viruses. Instead, we exploit their encapsulation of nucleic cargo, using three different fluorescent ATTO dyes linked to single-stranded DNA oligomers, which are hybridised to a longer DNA strand. FRET is induced upon assembly of the cowpea chlorotic mottle virus, which forms monodisperse icosahedral particles of about 22 nm, thereby increasing the FRET efficiency by a factor of 8. Additionally, encapsulation of the dyes in virus-like particles induces a two-step FRET. When the formed constructs are disassembled, this FRET signal is fully reduced to the value before encapsulation. This reversible behavior makes the system a good probe for studying viral assembly and disassembly. It, furthermore, shows that multi-component supramolecular materials are stabilized in the confinement of a protein cage.

The CD63-Syntenin-1 Complex Controls Post-Endocytic Trafficking of Oncogenic Human Papillomaviruses.

Science.gov (United States)

Gräßel, Linda; Fast, Laura Aline; Scheffer, Konstanze D; Boukhallouk, Fatima; Spoden, Gilles A; Tenzer, Stefan; Boller, Klaus; Bago, Ruzica; Rajesh, Sundaresan; Overduin, Michael; Berditchevski, Fedor; Florin, Luise

2016-08-31

Human papillomaviruses enter host cells via a clathrin-independent endocytic pathway involving tetraspanin proteins. However, post-endocytic trafficking required for virus capsid disassembly remains unclear. Here we demonstrate that the early trafficking pathway of internalised HPV particles involves tetraspanin CD63, syntenin-1 and ESCRT-associated adaptor protein ALIX. Following internalisation, viral particles are found in CD63-positive endosomes recruiting syntenin-1, a CD63-interacting adaptor protein. Electron microscopy and immunofluorescence experiments indicate that the CD63-syntenin-1 complex controls delivery of internalised viral particles to multivesicular endosomes. Accordingly, infectivity of high-risk HPV types 16, 18 and 31 as well as disassembly and post-uncoating processing of viral particles was markedly suppressed in CD63 or syntenin-1 depleted cells. Our analyses also present the syntenin-1 interacting protein ALIX as critical for HPV infection and CD63-syntenin-1-ALIX complex formation as a prerequisite for intracellular transport enabling viral capsid disassembly. Thus, our results identify the CD63-syntenin-1-ALIX complex as a key regulatory component in post-endocytic HPV trafficking.

Effect of overcharge on Li(Ni0.5Mn0.3Co0.2)O2/graphite lithium ion cells with poly(vinylidene fluoride) binder. III - Chemical changes in the cathode

Science.gov (United States)

Bareño, Javier; Dietz Rago, Nancy; Dogan, Fulya; Graczyk, Donald G.; Tsai, Yifen; Naik, Seema R.; Han, Sang-Don; Lee, Eungje; Du, Zhijia; Sheng, Yangping; Li, Jianlin; Wood, David L.; Steele, Leigh Anna; Lamb, Joshua; Spangler, Scott; Grosso, Christopher; Fenton, Kyle; Bloom, Ira

2018-05-01

1.5 Ah pouch cells based on Li(Ni0.5Mn0.3Co0.2)O2 cathodes and graphite anodes, both containing poly (vinylidene fluoride) (PVDF) binders, were systematically overcharged to 100, 120, 140, 160, 180, and 250% state of charge (SOC), at which point they vented. The cells were subsequently discharged to 0% SOC and disassembled under an inert atmosphere for characterization. A combination of X-ray photoelectron spectroscopy (XPS), scanning-electron microscopy (SEM), energy-dispersive spectroscopy (EDS), 6Li SSNMR, and X-ray diffraction (XRD) analysis of the NMC532 cathodes indicates the formation of a thin C- and O-rich cathode electrolyte interphase layer, progressive Li loss above 140% SOC, and retention of the bulk crystal structure at all states of charge.

Multifragmentation in central Kr+Au collisions at 60 MeV/u

International Nuclear Information System (INIS)

Lopez, O.; Aboufirassi, M.; Bougault, R.; Brou, R.; Colin, J.; Durand, D.; Genoux-Lubain, A.; Laville, J.L.; Lecolley, J.F.; Lefebvres, F.; Le Brun, C.; Louvel, M.; Mahi, M.; Paulot, C.; Steckmeyer, J.C.; Tamain, B.; Horn, D.

1994-01-01

We studied multifragmentation reaction kinetics, and tried to analyse whether the disassembly process is simultaneous or sequential. We performed central Kr+Au collisions at 60 MeV/u. After a careful selection of central events by requiring identical parallel and transverse center-of-mass velocity distribution, events have been compared with two computer simulations: standard statistical prescriptions with sequential emission of fragments, and Lopez-Randrup formalism assuming a simultaneous emission of fragments. A good agreement with simultaneous model leads us to the conclusion that booth simulations (prompt and simultaneous fragment emission) match the disassembly process. (D.L.). 14 refs., 2 figs

Microtubules as a Critical Target for Arsenic Toxicity in Lung Cells in Vitro and in Vivo

Directory of Open Access Journals (Sweden)

Yinzhi Zhao

2012-02-01

Full Text Available To understand mechanisms for arsenic toxicity in the lung, we examined effects of sodium m-arsenite (As3+ on microtubule (MT assembly in vitro (0–40 µM, in cultured rat lung fibroblasts (RFL6, 0–20 µM for 24 h and in the rat animal model (intratracheal instillation of 2.02 mg As/kg body weight, once a week for 5 weeks. As3+ induced a dose-dependent disassembly of cellular MTs and enhancement of the free tubulin pool, initiating an autoregulation of tubulin synthesis manifest as inhibition of steady-state mRNA levels of βI-tubulin in dosed lung cells and tissues. Spindle MT injuries by As3+ were concomitant with chromosomal disorientations. As3+ reduced the binding to tubulin of [3H]N-ethylmaleimide (NEM, an -SH group reagent, resulting in inhibition of MT polymerization in vitro with bovine brain tubulins which was abolished by addition of dithiothreitol (DTT suggesting As3+ action upon tubulin through -SH groups. In response to As3+, cells elevated cellular thiols such as metallothionein. Taxol, a tubulin polymerization agent, antagonized both As3+ and NEM induced MT depolymerization. MT–associated proteins (MAPs essential for the MT stability were markedly suppressed in As3+-treated cells. Thus, tubulin sulfhydryls and MAPs are major molecular targets for As3+ damage to the lung triggering MT disassembly cascades.

History and current status of nuclear fuel reprocessing technology

International Nuclear Information System (INIS)

Funasaka, Hideyuki; Nagai, Toshihisa; Washiya, Tadahiro

2008-01-01

History and present state of fast breeder reactor was reviewed in series. As a history and current status of nuclear fuel reprocessing technology, this ninth lecture presented the progress of the FBR fuel reprocessing technology and advanced reprocessing processes. FBR fuel reprocessing technology had been developed to construct the reprocessing equipment test facilities (RETF) based on PUREX process technologies. With economics, reduction of environmental burdens and proliferation resistance taken into consideration, advanced aqueous method for nuclear fuel cycle activities has been promoted as the government's basic policy. Innovative technologies on mechanical disassembly, continuous rotary dissolver, crystallizer, solvent extraction and actinides recovery have been mainly studied. (T. Tanaka)

Depth of manual dismantling analysis: A cost–benefit approach

Energy Technology Data Exchange (ETDEWEB)

Achillas, Ch., E-mail: c.achillas@ihu.edu.gr [School of Economics and Business Administration, International Hellenic University, 14th km Thessaloniki-Moudania, 57001 Thermi (Greece); Aidonis, D. [Department of Logistics, Alexander Technological Educational Institute, Branch of Katerini, 60100 Katerini (Greece); Vlachokostas, Ch.; Karagiannidis, A.; Moussiopoulos, N.; Loulos, V. [Laboratory of Heat Transfer and Environmental Engineering, Department of Mechanical Engineering, Aristotle University, Thessaloniki, Box 483, 54124 Thessaloniki (Greece)

2013-04-15

Highlights: ► A mathematical modeling tool for OEMs. ► The tool can be used by OEMs, recyclers of electr(on)ic equipment or WEEE management systems’ regulators. ► The tool makes use of cost–benefit analysis in order to determine the optimal depth of product disassembly. ► The reusable materials and the quantity of metals and plastics recycled can be quantified in an easy-to-comprehend manner. - Abstract: This paper presents a decision support tool for manufacturers and recyclers towards end-of-life strategies for waste electrical and electronic equipment. A mathematical formulation based on the cost benefit analysis concept is herein analytically described in order to determine the parts and/or components of an obsolete product that should be either non-destructively recovered for reuse or be recycled. The framework optimally determines the depth of disassembly for a given product, taking into account economic considerations. On this basis, it embeds all relevant cost elements to be included in the decision-making process, such as recovered materials and (depreciated) parts/components, labor costs, energy consumption, equipment depreciation, quality control and warehousing. This tool can be part of the strategic decision-making process in order to maximize profitability or minimize end-of-life management costs. A case study to demonstrate the models’ applicability is presented for a typical electronic product in terms of structure and material composition. Taking into account the market values of the pilot product’s components, the manual disassembly is proven profitable with the marginal revenues from recovered reusable materials to be estimated at 2.93–23.06 €, depending on the level of disassembly.

Depth of manual dismantling analysis: A cost–benefit approach

International Nuclear Information System (INIS)

Achillas, Ch.; Aidonis, D.; Vlachokostas, Ch.; Karagiannidis, A.; Moussiopoulos, N.; Loulos, V.

2013-01-01

Highlights: ► A mathematical modeling tool for OEMs. ► The tool can be used by OEMs, recyclers of electr(on)ic equipment or WEEE management systems’ regulators. ► The tool makes use of cost–benefit analysis in order to determine the optimal depth of product disassembly. ► The reusable materials and the quantity of metals and plastics recycled can be quantified in an easy-to-comprehend manner. - Abstract: This paper presents a decision support tool for manufacturers and recyclers towards end-of-life strategies for waste electrical and electronic equipment. A mathematical formulation based on the cost benefit analysis concept is herein analytically described in order to determine the parts and/or components of an obsolete product that should be either non-destructively recovered for reuse or be recycled. The framework optimally determines the depth of disassembly for a given product, taking into account economic considerations. On this basis, it embeds all relevant cost elements to be included in the decision-making process, such as recovered materials and (depreciated) parts/components, labor costs, energy consumption, equipment depreciation, quality control and warehousing. This tool can be part of the strategic decision-making process in order to maximize profitability or minimize end-of-life management costs. A case study to demonstrate the models’ applicability is presented for a typical electronic product in terms of structure and material composition. Taking into account the market values of the pilot product’s components, the manual disassembly is proven profitable with the marginal revenues from recovered reusable materials to be estimated at 2.93–23.06 €, depending on the level of disassembly

Evaluating the treatment of E-waste a case study of discarded refrigerators

Institute of Scientific and Technical Information of China (English)

DENG Jian-jun; WEN Xue-feng; ZHAO Yue-min

2008-01-01

Disassembly and recycling of E-waste creates a series of environmental problems. The selection of a technologically reliable, environmentally friendly, economically affordable and socially acceptable recycling technology for E-waste is a significant question. This study establishes a Monte-Carlo mathematical model of cost minimization, given the constraints of environmentally sound handling of the e-waste, in the context of Crystal Ball risk assessment and evaluation software. By following the streams of the different treatment processes, which consist of various technologies including disassembly, recycling and disposal, the econom-ics of various possibilities were identified and the optimal recycling technology proposed. The key factors of the proposed scenarios were determined by using sensitivity analysis. The results of this study show that, for discarded refrigerators, the operating life span plays the key role. The model supports maintenance and resale of the short lived refrigerators. For the longer lived refrigerators material recycling is recommended by the model. Sensitivity analysis shows that purchase cost, plastic sale price, condenser sale price and disassembly costs are the main effects. This study provides a significant technical support for policy making in E-waste management.

Dining at the periodic table: metals concentrations as they relate to recycling.

Science.gov (United States)

Johnson, Jeremiah; Harper, E M; Lifset, Reid; Graedel, T E

2007-03-01

A correlation between the prices of a variety of substances and their dilutions in their initial matrices was shown in 1959 by T.K. Sherwood. The research presented here shows that the relationship holds for engineering metals today, which we termed the metals-specific Sherwood plot. The concentrations of metals in products (e.g., printed wiring boards and automobiles) and waste streams (e.g., municipal solid waste, and construction and demolition debris) were plotted with this correlation. In addition, for the products and waste streams that undergo disassembly at end-of-life, the metals concentrations of the disassembled components were also plotted. It was found that most of the metals that are currently targeted for recycling have post-disassembly concentrations that lie above the metals-specific Sherwood plot (i.e., have concentrations that are more enriched than minimum profitable ore grades). This suggests that material concentration plays a role in the viability of recycling at end-of-life. As products grow in complexity and the variety of materials used, analyses such as this one provide insight for policymakers and those interested in material sustainability into macro-level trends of material use and future recycling practices.

RAP-2A Computer code for transients analysis in fast reactors

International Nuclear Information System (INIS)

Iftode, I.; Popescu, C.; Turcu, I.; Biro, L.

1975-10-01

The RAP-2A computer code is designed for analyzing thermohydraulic transients and/or steady state problems for large LMFBR cores. Physical and mathematical models, main input-output data, the flow chart of the code and a sample problem are given. RAP-2A calculates the power and the thermoydraulic transients initiated by a flow or reactivity changes, from a normal operating state of the reactor up to core disassembly. In this analysis a representative fuel pin is considered: a one-group space-independent (point) kinetics model to describe the neutron kinetics and a one-dimensional model describing the heat transfer (radial in the fuel and axial in the coolant) are used. Mechanical deformations due to temperature gradient, pressure losses, fuel melting, etc., are also calculated. The code is written in FORTRAN-4 language and is running on a IBM-370/135 computer

Distributed model predictive control for constrained nonlinear systems with decoupled local dynamics.

Science.gov (United States)

Zhao, Meng; Ding, Baocang

2015-03-01

This paper considers the distributed model predictive control (MPC) of nonlinear large-scale systems with dynamically decoupled subsystems. According to the coupled state in the overall cost function of centralized MPC, the neighbors are confirmed and fixed for each subsystem, and the overall objective function is disassembled into each local optimization. In order to guarantee the closed-loop stability of distributed MPC algorithm, the overall compatibility constraint for centralized MPC algorithm is decomposed into each local controller. The communication between each subsystem and its neighbors is relatively low, only the current states before optimization and the optimized input variables after optimization are being transferred. For each local controller, the quasi-infinite horizon MPC algorithm is adopted, and the global closed-loop system is proven to be exponentially stable. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

Hierarchically assembled DNA origami tubules with reconfigurable chirality

International Nuclear Information System (INIS)

Chen, Haorong; Cha, Tae-Gon; Pan, Jing; Choi, Jong Hyun

2013-01-01

The dynamic reconfiguration of a hierarchically assembled tubular structure is demonstrated using the DNA origami technique. Short cylindrical DNA origami monomers are synthesized and linked into elongated tubules, which can then be disassembled via toehold-mediated strand displacement. The disassembled subunits are subsequently linked into tubules of a different chirality. The reconfiguration is performed with the subunits carrying dumbbell hairpin DNA oligonucleotides or gold nanoparticles (AuNPs). The reconfiguration of higher order origami structures presented here is useful for constructing dynamic nanostructures that exceed the size limit of single DNA origami and may facilitate the study of molecular or particle interactions by tuning their relative distance and organization. (paper)

Colossal Tooling Design: 3D Simulation for Ergonomic Analysis

Science.gov (United States)

Hunter, Steve L.; Dischinger, Charles; Thomas, Robert E.; Babai, Majid

2003-01-01

The application of high-level 3D simulation software to the design phase of colossal mandrel tooling for composite aerospace fuel tanks was accomplished to discover and resolve safety and human engineering problems. The analyses were conducted to determine safety, ergonomic and human engineering aspects of the disassembly process of the fuel tank composite shell mandrel. Three-dimensional graphics high-level software, incorporating various ergonomic analysis algorithms, was utilized to determine if the process was within safety and health boundaries for the workers carrying out these tasks. In addition, the graphical software was extremely helpful in the identification of material handling equipment and devices for the mandrel tooling assembly/disassembly process.

Multiligand Metal-Phenolic Assembly from Green Tea Infusions.

Science.gov (United States)

Rahim, Md Arifur; Björnmalm, Mattias; Bertleff-Zieschang, Nadja; Ju, Yi; Mettu, Srinivas; Leeming, Michael G; Caruso, Frank

2018-03-07

The synthesis of hybrid functional materials using the coordination-driven assembly of metal-phenolic networks (MPNs) is of interest in diverse areas of materials science. To date, MPN assembly has been explored as monoligand systems (i.e., containing a single type of phenolic ligand) where the phenolic components are primarily obtained from natural sources via extraction, isolation, and purification processes. Herein, we demonstrate the fabrication of MPNs from a readily available, crude phenolic source-green tea (GT) infusions. We employ our recently introduced rust-mediated continuous assembly strategy to prepare these GT MPN systems. The resulting hollow MPN capsules contain multiple phenolic ligands and have a shell thickness that can be controlled through the reaction time. These multiligand MPN systems have different properties compared to the analogous MPN systems reported previously. For example, the Young's modulus (as determined using colloidal-probe atomic force microscopy) of the GT MPN system presented herein is less than half that of MPN systems prepared using tannic acid and iron salt solutions, and the disassembly kinetics are faster (∼50%) than other, comparable MPN systems under identical disassembly conditions. Additionally, the use of rust-mediated assembly enables the formation of stable capsules under conditions where the conventional approach (i.e., using iron salt solutions) results in colloidally unstable dispersions. These differences highlight how the choice of phenolic ligand and its source, as well as the assembly protocol (e.g., using solution-based or solid-state iron sources), can be used to tune the properties of MPNs. The strategy presented herein expands the toolbox of MPN assembly while also providing new insights into the nature and robustness of metal-phenolic interfacial assembly when using solution-based or solid-state metal sources.

The 871 keV gamma ray from 17O and the identification of plutonium oxide

International Nuclear Information System (INIS)

Peurrung, Anthony; Arthur, Richard; Elovich, Robert; Geelhood, Bruce; Kouzes, Richard; Pratt, Sharon; Scheele, Randy; Sell, Richard

2001-01-01

Disarmament agreements and discussions between the United States and the Russian Federation for reducing the number of stockpiled nuclear weapons require verification of the origin of materials as having come from disassembled weapons. This has resulted in the identification of measurable 'attributes' that characterize such materials. It has been proposed that the 871 keV gamma ray of 17 O can be observed as an indicator of the unexpected presence of plutonium oxide, as opposed to plutonium metal, in such materials. We have shown that the observation of the 871 keV gamma ray is not a specific indicator of the presence of the oxide, but rather indicates the presence of nitrogen

Coolability of severely degraded CANDU cores. Revised

International Nuclear Information System (INIS)

Meneley, D.A.; Blahnik, C.; Rogers, J.T.; Snell, V.G.; Nijhawan, S.

1996-01-01

Analytical and experimental studies have shown that the separately cooled moderator in a CANDU reactor provides an effective heat sink in the event of a loss-of-coolant accident (LOCA) accompanied by total failure of the emergency core cooling system (ECCS). The moderator heat sink prevents fuel melting and maintains the integrity of the fuel channels, therefore terminating this severe accident short of severe core damage. Nevertheless, there is a probability, however low, that the moderator heat sink could fail in such an accident. The pioneering work of Rogers (1984) for such a severe accident using simplified models showed that the fuel channels would fail and a bed of dry, solid debris would be formed at the bottom of the calandria which would heat up and eventually melt. However, the molten pool of core material would be retained in the calandria vessel, cooled by the independently cooled shield-tank water, and would eventually resolidify. Thus, the calandria vessel would act inherently as a 'core-catcher' as long as the shield tank integrity is maintained. The present paper reviews subsequent work on the damage to a CANDU core under severe accident conditions and describes an empirically based mechanistic model of this process. It is shown that, for such severe accident sequences in a CANDU reactor, the end state following core disassembly consists of a porous bed of dry solid, coarse debris, irrespective of the initiating event and the core disassembly process. (author)

Binding of Substrates to the Central Pore of the Vps4 ATPase Is Autoinhibited by the Microtubule Interacting and Trafficking (MIT) Domain and Activated by MIT Interacting Motifs (MIMs).

Science.gov (United States)

Han, Han; Monroe, Nicole; Votteler, Jörg; Shakya, Binita; Sundquist, Wesley I; Hill, Christopher P

2015-05-22

The endosomal sorting complexes required for transport (ESCRT) pathway drives reverse topology membrane fission events within multiple cellular pathways, including cytokinesis, multivesicular body biogenesis, repair of the plasma membrane, nuclear membrane vesicle formation, and HIV budding. The AAA ATPase Vps4 is recruited to membrane necks shortly before fission, where it catalyzes disassembly of the ESCRT-III lattice. The N-terminal Vps4 microtubule-interacting and trafficking (MIT) domains initially bind the C-terminal MIT-interacting motifs (MIMs) of ESCRT-III subunits, but it is unclear how the enzyme then remodels these substrates in response to ATP hydrolysis. Here, we report quantitative binding studies that demonstrate that residues from helix 5 of the Vps2p subunit of ESCRT-III bind to the central pore of an asymmetric Vps4p hexamer in a manner that is dependent upon the presence of flexible nucleotide analogs that can mimic multiple states in the ATP hydrolysis cycle. We also find that substrate engagement is autoinhibited by the Vps4p MIT domain and that this inhibition is relieved by binding of either Type 1 or Type 2 MIM elements, which bind the Vps4p MIT domain through different interfaces. These observations support the model that Vps4 substrates are initially recruited by an MIM-MIT interaction that activates the Vps4 central pore to engage substrates and generate force, thereby triggering ESCRT-III disassembly. © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

Binding of Substrates to the Central Pore of the Vps4 ATPase Is Autoinhibited by the Microtubule Interacting and Trafficking (MIT) Domain and Activated by MIT Interacting Motifs (MIMs)*

Science.gov (United States)

Han, Han; Monroe, Nicole; Votteler, Jörg; Shakya, Binita; Sundquist, Wesley I.; Hill, Christopher P.

2015-01-01

The endosomal sorting complexes required for transport (ESCRT) pathway drives reverse topology membrane fission events within multiple cellular pathways, including cytokinesis, multivesicular body biogenesis, repair of the plasma membrane, nuclear membrane vesicle formation, and HIV budding. The AAA ATPase Vps4 is recruited to membrane necks shortly before fission, where it catalyzes disassembly of the ESCRT-III lattice. The N-terminal Vps4 microtubule-interacting and trafficking (MIT) domains initially bind the C-terminal MIT-interacting motifs (MIMs) of ESCRT-III subunits, but it is unclear how the enzyme then remodels these substrates in response to ATP hydrolysis. Here, we report quantitative binding studies that demonstrate that residues from helix 5 of the Vps2p subunit of ESCRT-III bind to the central pore of an asymmetric Vps4p hexamer in a manner that is dependent upon the presence of flexible nucleotide analogs that can mimic multiple states in the ATP hydrolysis cycle. We also find that substrate engagement is autoinhibited by the Vps4p MIT domain and that this inhibition is relieved by binding of either Type 1 or Type 2 MIM elements, which bind the Vps4p MIT domain through different interfaces. These observations support the model that Vps4 substrates are initially recruited by an MIM-MIT interaction that activates the Vps4 central pore to engage substrates and generate force, thereby triggering ESCRT-III disassembly. PMID:25833946

Actin-interacting protein 1 controls assembly and permeability of intestinal epithelial apical junctions.

Science.gov (United States)

Lechuga, Susana; Baranwal, Somesh; Ivanov, Andrei I

2015-05-01

Adherens junctions (AJs) and tight junctions (TJs) are crucial regulators of the integrity and restitution of the intestinal epithelial barrier. The structure and function of epithelial junctions depend on their association with the cortical actin cytoskeleton that, in polarized epithelial cells, is represented by a prominent perijunctional actomyosin belt. The assembly and stability of the perijunctional cytoskeleton is controlled by constant turnover (disassembly and reassembly) of actin filaments. Actin-interacting protein (Aip) 1 is an emerging regulator of the actin cytoskeleton, playing a critical role in filament disassembly. In this study, we examined the roles of Aip1 in regulating the structure and remodeling of AJs and TJs in human intestinal epithelium. Aip1 was enriched at apical junctions in polarized human intestinal epithelial cells and normal mouse colonic mucosa. Knockdown of Aip1 by RNA interference increased the paracellular permeability of epithelial cell monolayers, decreased recruitment of AJ/TJ proteins to steady-state intercellular contacts, and attenuated junctional reassembly in a calcium-switch model. The observed defects of AJ/TJ structure and functions were accompanied by abnormal organization and dynamics of the perijunctional F-actin cytoskeleton. Moreover, loss of Aip1 impaired the apico-basal polarity of intestinal epithelial cell monolayers and inhibited formation of polarized epithelial cysts in 3-D Matrigel. Our findings demonstrate a previously unanticipated role of Aip1 in regulating the structure and remodeling of intestinal epithelial junctions and early steps of epithelial morphogenesis. Copyright © 2015 the American Physiological Society.

Characterization of radioactive graphite and concrete of the reactor ULYSSE/INSTN at CEA/Saclay to be dismantled

International Nuclear Information System (INIS)

Van Lauwe, Aymeric; Ridikas, Danas; Damoy, Francois; Blideanu, Valentin; Fajardo, Christophe; Aubert, Marie-Cecile; Foulon, Francois

2006-01-01

Decommissioning and dismantling of nuclear installations after their service life are connected with the necessity of the disassembling, handling and disposing of a large amount of radioactive material. In order to optimize the disassembling operations, to reduce the undesirable volume to the minimum and to successfully plan the dismantling and disposal of radioactive materials to storage facilities, the radiological characterisation of the material present in the reactor and around its environment should be accurately evaluated. The present work has been done in the framework of the decommissioning and dismantling of the experimental reactor ULYSSE that is presently operating in INSTN/Saclay and will be closed in the middle of 2006. A methodology, already successfully used for another research reactor, is proposed for determining accurately the long-term induced activity of the materials present in the active reactor core and its surroundings. The comparison of theoretical predictions, based on Monte Carlo technique, with experimental values validated the approach and the methodology used in the present study. The goal is to plan efficiently the disassembling and dismantling of the system and to optimise the mass flow going to different waste repositories. We show that this approach might reduce substantially the total cost of decommissioning. (authors)

Structural Insights into the Association of Hif1 with Histones H2A-H2B Dimer and H3-H4 Tetramer.

Science.gov (United States)

Zhang, Mengying; Liu, Hejun; Gao, Yongxiang; Zhu, Zhongliang; Chen, Zijun; Zheng, Peiyi; Xue, Lu; Li, Jixi; Teng, Maikun; Niu, Liwen

2016-10-04

Histone chaperones are critical for guiding specific post-transcriptional modifications of histones, safeguarding the histone deposition (or disassociation) of nucleosome (dis)assembly, and regulating chromatin structures to change gene activities. HAT1-interacting factor 1 (Hif1) has been reported to be an H3-H4 chaperone and to be involved in telomeric silencing and nucleosome (dis)assembly. However, the structural basis for the interaction of Hif1 with histones remains unknown. Here, we report the complex structure of Hif1 binding to H2A-H2B for uncovering the chaperone specificities of Hif1 on binding to both the H2A-H2B dimer and the H3-H4 tetramer. Our findings reveal that Hif1 interacts with the H2A-H2B dimer and the H3-H4 tetramer via distinct mechanisms, suggesting that Hif1 is a pivotal scaffold on alternate binding of H2A-H2B and H3-H4. These specificities are conserved features of the Sim3-Hif1-NASP interrupted tetratricopeptide repeat proteins, which provide clues for investigating their potential roles in nucleosome (dis)assembly. Copyright © 2016 Elsevier Ltd. All rights reserved.

Conformational changes in the AAA ATPase p97–p47 adaptor complex

Science.gov (United States)

Beuron, Fabienne; Dreveny, Ingrid; Yuan, Xuemei; Pye, Valerie E; Mckeown, Ciaran; Briggs, Louise C; Cliff, Matthew J; Kaneko, Yayoi; Wallis, Russell; Isaacson, Rivka L; Ladbury, John E; Matthews, Steve J; Kondo, Hisao; Zhang, Xiaodong; Freemont, Paul S

2006-01-01

The AAA+ATPase p97/VCP, helped by adaptor proteins, exerts its essential role in cellular events such as endoplasmic reticulum-associated protein degradation or the reassembly of Golgi, ER and the nuclear envelope after mitosis. Here, we report the three-dimensional cryo-electron microscopy structures at ∼20 Å resolution in two nucleotide states of the endogenous hexameric p97 in complex with a recombinant p47 trimer, one of the major p97 adaptor proteins involved in membrane fusion. Depending on the nucleotide state, we observe the p47 trimer to be in two distinct arrangements on top of the p97 hexamer. By combining the EM data with NMR and other biophysical measurements, we propose a model of ATP-dependent p97(N) domain motions that lead to a rearrangement of p47 domains, which could result in the disassembly of target protein complexes. PMID:16601695

LEAP into the Pfizer Global Virtual Library (PGVL) space: creation of readily synthesizable design ideas automatically.

Science.gov (United States)

Hu, Qiyue; Peng, Zhengwei; Kostrowicki, Jaroslav; Kuki, Atsuo

2011-01-01

Pfizer Global Virtual Library (PGVL) of 10(13) readily synthesizable molecules offers a tremendous opportunity for lead optimization and scaffold hopping in drug discovery projects. However, mining into a chemical space of this size presents a challenge for the concomitant design informatics due to the fact that standard molecular similarity searches against a collection of explicit molecules cannot be utilized, since no chemical information system could create and manage more than 10(8) explicit molecules. Nevertheless, by accepting a tolerable level of false negatives in search results, we were able to bypass the need for full 10(13) enumeration and enabled the efficient similarity search and retrieval into this huge chemical space for practical usage by medicinal chemists. In this report, two search methods (LEAP1 and LEAP2) are presented. The first method uses PGVL reaction knowledge to disassemble the incoming search query molecule into a set of reactants and then uses reactant-level similarities into actual available starting materials to focus on a much smaller sub-region of the full virtual library compound space. This sub-region is then explicitly enumerated and searched via a standard similarity method using the original query molecule. The second method uses a fuzzy mapping onto candidate reactions and does not require exact disassembly of the incoming query molecule. Instead Basis Products (or capped reactants) are mapped into the query molecule and the resultant asymmetric similarity scores are used to prioritize the corresponding reactions and reactant sets. All sets of Basis Products are inherently indexed to specific reactions and specific starting materials. This again allows focusing on a much smaller sub-region for explicit enumeration and subsequent standard product-level similarity search. A set of validation studies were conducted. The results have shown that the level of false negatives for the disassembly-based method is acceptable when the

SP-100 reactor disassembly remote handling test program

International Nuclear Information System (INIS)

Wilson, C.E.; Potter, J.D.; Maiden, G.E.; Vader, D.P.

1991-01-01

This paper is presented as an overview of the remote handling equipment validation testing, which will be conducted before installation and use in the ground engineering test facility. This equipment will be used to defuel the SP-100 reactor core after removing it from the Test Assembly following nuclear testing. A series of full scale mock-up operational tests will be conducted at a Hanford Site facility to verify equipment design, operation, and capabilities

Functional and cosmetic outcome of partial penile disassembly ...

African Journals Online (AJOL)

A. Bhat

2017-07-04

Jul 4, 2017 ... Technique: Penile de-gloving with mobilization of urethral plate from ventral to dorsal ... BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/). ..... Literature search , Clinical studies, Experimental studies, Data.

Nuclear disassembly time scales using space time correlations

Energy Technology Data Exchange (ETDEWEB)

Durand, D.; Colin, J.; Lecolley, J.F.; Meslin, C.; Aboufirassi, M.; Bougault, R.; Brou, R. [Caen Univ., 14 (France). Lab. de Physique Corpusculaire; Bilwes, B.; Cosmo, F. [Strasbourg-1 Univ., 67 (France); Galin, J. [Grand Accelerateur National d`Ions Lourds (GANIL), 14 - Caen (France); and others

1996-09-01

The lifetime, {tau}, with respect to multifragmentation of highly excited nuclei is deduced from the analysis of strongly damped Pb+Au collisions at 29 MeV/u. The method is based on the study of space-time correlations induced by `proximity` effects between fragments emitted by the two primary products of the reaction and gives the time between the re-separation of the two primary products and the subsequent multifragment decay of one partner. (author). 2 refs.

Nuclear disassembly time scales using space time correlations

International Nuclear Information System (INIS)

Durand, D.; Colin, J.; Lecolley, J.F.; Meslin, C.; Aboufirassi, M.; Bougault, R.; Brou, R.; Galin, J.; and others.

1996-01-01

The lifetime, τ, with respect to multifragmentation of highly excited nuclei is deduced from the analysis of strongly damped Pb+Au collisions at 29 MeV/u. The method is based on the study of space-time correlations induced by 'proximity' effects between fragments emitted by the two primary products of the reaction and gives the time between the re-separation of the two primary products and the subsequent multifragment decay of one partner. (author)

Will biofilm disassembly agents make it to market?

Science.gov (United States)

Romero, Diego; Kolter, Roberto

2011-07-01

Nearly 12 years after promising results suggested that antibiofilm agents might be developed into novel therapeutics, there are no such products on the market. In our opinion, the reasons for this have been predominantly economic. Recent developments, however, suggest that there could still be emerging opportunities for the developments of such products. Copyright © 2011 Elsevier Ltd. All rights reserved.

Charge correlations as a probe of nuclear disassembly

International Nuclear Information System (INIS)

Kreutz, P.; Pochodzalla, J.; Schuettauf, A.; Tucholski, A.; Bouissou, P.; Leray, S.; Seidel, W.; Begemann-Blaich, M.; Hubele, J.; Kunde, G.J.; Lindenstruth, V.; Liu, Z.; Lynen, U.; Meijer, R.J.; Milkau, U.; Mueller, W.F.J.; Ogilvie, C.A.; Sann, H.; Trautmann, W.

1992-03-01

We have studied multi-fragment decays of Au projectiles after collision with C, Al, Cu and Pb targets at a bombarding energy of 600 MeV/nucleon. We examine the correlations between the charges emitted in these reactions. These correlations are given as a function of the total charge in bound fragments, Z bound , at forward angles, which is a measure of the violence of the collision and can be related to the impact parameter. The charge distributions have been fit by a power law and the extracted τ parameter exhibits a minimum as a function of Z bound . We observe a strong reduction in the maximum charge, Z max , of the event with decreasing Z bound . For those events where Z max is less than half Z bound , the relative sizes of the two largest charges within the event cover the full spectrum of possibilities. The charge-Dalitz plots indicate that the multi-fragmentation events are not an extension of symmetric fission reactions. The event-by-event charge moments are examined to measure the size of the charge fluctuations. All of the charge correlations are independent of the target when plotted as a function of Z bound . The results are compared to both nuclear statistical and percolation calculations. The model predictions differ from each other, establishing that the observables are sensitive to how the available phase space is populated. The sequential nuclear model predicts too asymmetric a decay, while the simultaneous model predicts too symmetrical a break-up. The percolation model, which was adjusted to reproduce the mean multiplicity of fragments and the size of Z max , correctly predicts the charge fluctuations. (orig.)

Open standard building in South Africa: new concepts, strategies and technologies

CSIR Research Space (South Africa)

Van Wyk, Llewellyn V

2008-03-01

Full Text Available representation; BIM; People- focussed design; manuals; guidelines Lean Construction; Manuals; Best Practice; Performance Metrics; Training; On Site Production; Rapid Assembly & Disassembly Methods Community Participation; Interactive Design...

State of the States 2016: Arts Education State Policy Summary

Science.gov (United States)

Aragon, Stephanie

2016-01-01

The "State of the States 2016" summarizes state policies for arts education identified in statute or administrative code for all 50 states and the District of Columbia. Information is based on a comprehensive search of state education statute and codes on each state's relevant websites. Complete results from this review are available in…

Nonequilibrium and generalized-ensemble molecular dynamics simulations for amyloid fibril

Energy Technology Data Exchange (ETDEWEB)

Okumura, Hisashi [Research Center for Computational Science, Institute for Molecular Science, Okazaki, Aichi 444-8585 (Japan); Department of Structural Molecular Science, The Graduate University for Advanced Studies, Okazaki, Aichi 444-8585 (Japan)

2015-12-31

Amyloids are insoluble and misfolded fibrous protein aggregates and associated with more than 20 serious human diseases. We perform all-atom molecular dynamics simulations of amyloid fibril assembly and disassembly.

Fuel elements handling device and method

International Nuclear Information System (INIS)

Jabsen, F.S.

1976-01-01

This invention relates to nuclear equipment and more particularly to methods and apparatus for the non-destructive inspection, manipulation, disassembly and assembly of reactor fuel elements and the like. (author)

Computational features of the MELT-III neutronics, thermal-hydraulics computer code system

International Nuclear Information System (INIS)

Wilburn, N.P.; Waltar, A.E.

1976-01-01

A multichannel, thermal-hydraulics, neutronic accident analysis program for simulating fast reactor behavior from a hypothetical accident inception to the start of core disassembly or to reactor shutdown is described

FMIT alignment cart

International Nuclear Information System (INIS)

Potter, R.C.; Dauelsberg, L.B.; Clark, D.C.; Grieggs, R.J.

1981-01-01

The Fusion Materials Irradiation Test (FMIT) Facility alignment cart must perform several functions. It must serve as a fixture to receive the drift-tube girder assembly when it is removed from the linac tank. It must transport the girder assembly from the linac vault to the area where alignment or disassembly is to take place. It must serve as a disassembly fixture to hold the girder while individual drift tubes are removed for repair. It must align the drift tube bores in a straight line parallel to the girder, using an optical system. These functions must be performed without violating any clearances found within the building. The bore tubes of the drift tubes will be irradiated, and shielding will be included in the system for easier maintenance

Maintenance features of the Compact Ignition Tokamak fusion reactor

International Nuclear Information System (INIS)

Spampinato, P.T.; Hager, E.R.

1987-01-01

The Compact Ignition Tokamak (CIT) is envisaged to be the next experimental machine in the US Fusion Program. Its use of deuterium/tritium fuel requires the implementation of remote handling technology for maintenance and disassembly operations. The reactor is surrounded by a close-proximity nuclear shield which is designed to permit personnel access within the test cell, one day after shutdown. With the shield in place, certain maintenance activities in the cell may be done hands-on. Maintenance on the reactor is accomplished remotely using a boom-mounted manipulator after disassembling the shield. Maintenance within the plasma chamber is accomplished with two articulated boom manipulators that are capable of operating in a vacuum environment. They are stored in a vacuum enclosure behind movable shield plugs

Design of an interventional magnetic resonance imaging coil for cerebral surgery

Science.gov (United States)

Xu, Yue; Wang, Wen-Tao; Wang, Wei-Min

2012-11-01

In clinical magnetic resonance imaging (MRI), the design of the radiofrequency (RF) coil is very important. For certain applications, the appropriate coil can produce an improved image quality. However, it is difficult to achieve a uniform B1 field and a high signal-to-noise ratio (SNR) simultaneously. In this article, we design an interventional transmitter-and-receiver RF coil for cerebral surgery. This coil adopts a disassembly structure that can be assembled and disassembled repeatedly on the cerebral surgery gantry to reduce the amount of interference from the MRI during surgery. The simulation results and the imaging experiments demonstrate that this coil can produce a uniform RF field, a high SNR, and a large imaging range to meet the requirements of the cerebral surgery.

Remote replacement of materials open-test assembly specimens at the FFTF/IEM cell

International Nuclear Information System (INIS)

Gibbons, P.W.; Ramsey, E.B.

1990-01-01

The Fast Flux Test Facility (FFTF) interim examination and maintenance (IEM) cell is used for the remote disassembly of irradiated fuel and materials experiments. The materials open-test assembly (MOTA) is brought to the IEM cell for materials test specimen removal. The specimens are shipped to the materials laboratory for sorting and installation in new specimen holders and then returned within 10 days to the IEM cell where they are installed in a new MOTA vehicle for further irradiation. Reconstituting a MOTA is a challenging remote operation involving dozens of steps and two separate facilities. Handling and disassembling sodium-wetted components pose interesting handling, cleaning, and disposal challenges. The success of this system is evidenced by its timely completion in the critical path of FFTF outage schedules

State of the States, 2012: Arts Education State Policy Summary

Science.gov (United States)

Arts Education Partnership (NJ1), 2012

2012-01-01

The "State of the States 2012" summarizes state policies for arts education identified in statute or code for all 50 states and the District of Columbia. Information is based primarily on results from the AEP Arts Education State Policy Survey conducted in 2010-11, and updated in April 2012.

Collective flow in central Ca + Ca and Nb + Nb collisions

International Nuclear Information System (INIS)

Fai, G.; Csernai, L.P.; Kapusta, J.I.

1986-01-01

Questions related to the entropy, equation of state and collective flow of nuclear matter are important to the authors understanding of high energy nuclear collisions. Completion of the analysis of exclusive measurements on central Ca + Ca and Nb + Nb collisions triggered renewed interest in these problems. In order to address the results of exclusive measurements, however, the complex multifragment final states of high energy nuclear collisions need to be incorporated in a theoretical description. The microcanonical event generator model provides statistically generated complete events that can be compared to the exclusive data on an event-by-event basis. To describe the disassembly of hot nuclear matter the model uses an approximate scheme in which the available final states are populated according to their microcanonical weight in phase space. This statistical description is front-ended with simple geometric ideas to divide the collision system into subsystems and with a prescription to share energy and momentum among the subsystems. Any physical quantity of interest is in principle calculable in the model if sufficient statistics is accumulated

Staying Sharp: Retention of Military Knowledge and Skills

National Research Council Canada - National Science Library

Wisher, Robert

1999-01-01

.... Memory for psychomotor skills varies, depending on whether the task is continuous, such as riding a bicycle, or discrete, such as executing the separate performance steps involved in disassembling a rifle...

Cassandre : a two-dimensional multigroup diffusion code for reactor transient analysis

International Nuclear Information System (INIS)

Arien, B.; Daniels, J.

1986-12-01

CASSANDRE is a two-dimensional (x-y or r-z) finite element neutronics code with thermohydraulics feedback for reactor dynamics prior to the disassembly phase. It uses the multigroup neutron diffusion theory. Its main characteristics are the use of a generalized quasistatic model, the use of a flexible multigroup point-kinetics algorithm allowing for spectral matching and the use of a finite element description. The code was conceived in order to be coupled with any thermohydraulics module, although thermohydraulics feedback is only considered in r-z geometry. In steady state criticality search is possible either by control rod insertion or by homogeneous poisoning of the coolant. This report describes the main characterstics of the code structure and provides all the information needed to use the code. (Author)

Instability in nuclear dynamics: loss of collectivity and multifragmentation

International Nuclear Information System (INIS)

Colonna, M.; Di Toro, M.; Guarnera, A.; Latora, V.; Smerzi, A.

1995-01-01

Two limiting cases of nuclear dynamics are analysed: the disappearing of giant collective motions in hot nuclei and the nuclear disassembly in violent heavy ion collisions. For collective vibration build on excited states we get a dramatic increase of the widths of hot Giant Dipole Resonances (GDR). As a consequence of the competition with particle evaporation we get a sharp quenching of giant photon emission. Pre-equilibrium effects on the GDR formation are also accounted for. At high temperature and low density the collective motions can become unstable leading to multifragmentation events in heavy ion collisions. We present a general procedure to identify instability regions and to get informations on the instability point. Some hints towards fully dynamical picture of multi-fragmentation processes are finally suggested. (author)

Bacterial subversion of host actin dynamics at the plasma membrane.

Science.gov (United States)

Carabeo, Rey

2011-10-01

Invasion of non-phagocytic cells by a number of bacterial pathogens involves the subversion of the actin cytoskeletal remodelling machinery to produce actin-rich cell surface projections designed to engulf the bacteria. The signalling that occurs to induce these actin-rich structures has considerable overlap among a diverse group of bacteria. The molecular organization within these structures act in concert to internalize the invading pathogen. This dynamic process could be subdivided into three acts - actin recruitment, engulfment, and finally, actin disassembly/internalization. This review will present the current state of knowledge of the molecular processes involved in each stage of bacterial invasion, and provide a perspective that highlights the temporal and spatial control of actin remodelling that occurs during bacterial invasion. © 2011 Blackwell Publishing Ltd.

The power tool

International Nuclear Information System (INIS)

HAYFIELD, J.P.

1999-01-01

POWER Tool--Planning, Optimization, Waste Estimating and Resourcing tool, a hand-held field estimating unit and relational database software tool for optimizing disassembly and final waste form of contaminated systems and equipment

Neural-Network Quantum States, String-Bond States, and Chiral Topological States

Science.gov (United States)

Glasser, Ivan; Pancotti, Nicola; August, Moritz; Rodriguez, Ivan D.; Cirac, J. Ignacio

2018-01-01

Neural-network quantum states have recently been introduced as an Ansatz for describing the wave function of quantum many-body systems. We show that there are strong connections between neural-network quantum states in the form of restricted Boltzmann machines and some classes of tensor-network states in arbitrary dimensions. In particular, we demonstrate that short-range restricted Boltzmann machines are entangled plaquette states, while fully connected restricted Boltzmann machines are string-bond states with a nonlocal geometry and low bond dimension. These results shed light on the underlying architecture of restricted Boltzmann machines and their efficiency at representing many-body quantum states. String-bond states also provide a generic way of enhancing the power of neural-network quantum states and a natural generalization to systems with larger local Hilbert space. We compare the advantages and drawbacks of these different classes of states and present a method to combine them together. This allows us to benefit from both the entanglement structure of tensor networks and the efficiency of neural-network quantum states into a single Ansatz capable of targeting the wave function of strongly correlated systems. While it remains a challenge to describe states with chiral topological order using traditional tensor networks, we show that, because of their nonlocal geometry, neural-network quantum states and their string-bond-state extension can describe a lattice fractional quantum Hall state exactly. In addition, we provide numerical evidence that neural-network quantum states can approximate a chiral spin liquid with better accuracy than entangled plaquette states and local string-bond states. Our results demonstrate the efficiency of neural networks to describe complex quantum wave functions and pave the way towards the use of string-bond states as a tool in more traditional machine-learning applications.

Generic concept to program the time domain of self-assemblies with a self-regulation mechanism.

Science.gov (United States)

Heuser, Thomas; Steppert, Ann-Kathrin; Lopez, Catalina Molano; Zhu, Baolei; Walther, Andreas

2015-04-08

Nature regulates complex structures in space and time via feedback loops, kinetically controlled transformations, and under energy dissipation to allow non-equilibrium processes. Although man-made static self-assemblies realize excellent control over hierarchical structures via molecular programming, managing their temporal destiny by self-regulation is a largely unsolved challenge. Herein, we introduce a generic concept to control the time domain by programming the lifetimes of switchable self-assemblies in closed systems. We conceive dormant deactivators that, in combination with fast promoters, enable a unique kinetic balance to establish an autonomously self-regulating, transient pH-state, whose duration can be programmed over orders of magnitude-from minutes to days. Coupling this non-equilibrium state to pH-switchable self-assemblies allows predicting their assembly/disassembly fate in time, similar to a precise self-destruction mechanism. We demonstrate a platform approach by programming self-assembly lifetimes of block copolymers, nanoparticles, and peptides, enabling dynamic materials with a self-regulation functionality.

Dismantling and removal of the Niederaichbach nuclear power plant (KKN) to the 'Green Field'. Final report

International Nuclear Information System (INIS)

Valencia, L.; Prechtl, E.

1998-04-01

The major objective of the present project consisted in the complete dismantling and removal of the Niederaichbach nuclear power plant (KKN), ranging from the state of safe enclosure to re-establishing the original state of vegetation of the site (so-called 'green field'). By reaching this objective, principle feasibility of the complete removal of a power reactor was demonstrated. In addition, considerable experience has been gained with regard to the execution of all phases of such a complex project and project optimization. The following phases of the project can be distinguished: - Licensing procedure - dismantling of the inactive, contaminated and activated plant sections - disassembly of the activated building structures and decontamination of the buildings - demolition (conventional) of the buildings and recultivation of the site. Moreover, the project included the work performed under the direct supervision of the licensing authority, comprehensive radiation protection activities, the solution of waste management problems and the respective public relations work. (orig./MM) [de

Corrective Action Plan for Corrective Action Unit 143: Area 25 Contaminated Waste Dumps, Nevada Test Site, Nevada

International Nuclear Information System (INIS)

Gustafason, D.L.

2001-01-01

This Corrective Action Plan (CAP) has been prepared for Corrective Action Unit (CAU) 143: Area 25 Contaminated Waste Dumps, Nevada Test Site, Nevada, in accordance with the Federal Facility Agreement and Consent Order of 1996. This CAP provides the methodology for implementing the approved corrective action alternative as listed in the Corrective Action Decision Document (U.S. Department of Energy, Nevada Operations Office, 2000). The CAU includes two Corrective Action Sites (CASs): 25-23-09, Contaminated Waste Dump Number 1; and 25-23-03, Contaminated Waste Dump Number 2. Investigation of CAU 143 was conducted in 1999. Analytes detected during the corrective action investigation were evaluated against preliminary action levels to determine constituents of concern for CAU 143. Radionuclide concentrations in disposal pit soil samples associated with the Reactor Maintenance, Assembly, and Disassembly Facility West Trenches, the Reactor Maintenance, Assembly, and Disassembly Facility East Trestle Pit, and the Engine Maintenance, Assembly, and Disassembly Facility Trench are greater than normal background concentrations. These constituents are identified as constituents of concern for their respective CASs. Closure-in-place with administrative controls involves use restrictions to minimize access and prevent unauthorized intrusive activities, earthwork to fill depressions to original grade, placing additional clean cover material over the previously filled portion of some of the trenches, and placing secondary or diversion berm around pertinent areas to divert storm water run-on potential

Timely Endocytosis of Cytokinetic Enzymes Prevents Premature Spindle Breakage during Mitotic Exit.

Directory of Open Access Journals (Sweden)

Cheen Fei Chin

2016-07-01

Full Text Available Cytokinesis requires the spatio-temporal coordination of membrane deposition and primary septum (PS formation at the division site to drive acto-myosin ring (AMR constriction. It has been demonstrated that AMR constriction invariably occurs only after the mitotic spindle disassembly. It has also been established that Chitin Synthase II (Chs2p neck localization precedes mitotic spindle disassembly during mitotic exit. As AMR constriction depends upon PS formation, the question arises as to how chitin deposition is regulated so as to prevent premature AMR constriction and mitotic spindle breakage. In this study, we propose that cells regulate the coordination between spindle disassembly and AMR constriction via timely endocytosis of cytokinetic enzymes, Chs2p, Chs3p, and Fks1p. Inhibition of endocytosis leads to over accumulation of cytokinetic enzymes during mitotic exit, which accelerates the constriction of the AMR, and causes spindle breakage that eventually could contribute to monopolar spindle formation in the subsequent round of cell division. Intriguingly, the mitotic spindle breakage observed in endocytosis mutants can be rescued either by deleting or inhibiting the activities of, CHS2, CHS3 and FKS1, which are involved in septum formation. The findings from our study highlight the importance of timely endocytosis of cytokinetic enzymes at the division site in safeguarding mitotic spindle integrity during mitotic exit.

Coolability of severely degraded CANDU cores

International Nuclear Information System (INIS)

Meneley, D.A.; Blahnik, C.; Rogers, J.T.; Snell, V.G.; Mijhawan, S.

1995-07-01

Analytical and experimental studies have shown that the separately cooled moderator in a CANDU reactor provides an effective heat sink in the event of a loss-of-coolant accident (LOCA) accompanied by total failure of the emergency core cooling system (ECCS). The moderator heat sink prevents fuel melting and maintains the integrity of the fuel channels, therefore terminating this severe accident short of severe core damage. Nevertheless, there is a probability, however low, that the moderator heat sink could fail in such an accident. The pioneering work of Rogers (1984) for such a severe accident using simplified models showed that the fuel channels would fail and a bed of dry, solid debris would be formed at the bottom of the calandria which would heat up and eventually melt. However, the molten pool of core material would be retained in the calandria vessel, cooled by the independently cooled shield-tank water, and would eventually re solidify. Thus, the calandria vessel would act inherently as a core-catcher as long as the shield tank integrity is maintained. The present paper reviews subsequent work on the damage to a CANDU core under severe accident conditions and describes an empirically based mechanistic model of this process. It is shown that, for such severe accident sequences in a CANDU reactor, the end state following core disassembly consists of a porous bed of dry solid, coarse debris, irrespective of the initiating event and the core disassembly process. (author). 48 refs., 3 tabs., 18 figs

Metal Top Adapter ACV0000807, Manufactured by Delfasco, Inc. for Alliant Techsystems, Inc., for PA116 Containers on a 44" x 40" Wood Pallet, First Article Tests (FATs) IAW MIL-STD-1660, "Design Criteria for Ammunition Unit Loads"

National Research Council Canada - National Science Library

Dugan, Jeffery L

2008-01-01

...) test units were tested with a load of 2,495 lbs each. The tests accomplished on the test units were the Stacking, Repetitive Shock, Drop, Incline-Impact, Sling Compatibility, Forklifting, and Disassembly Tests...

Limiting Temperatures, Caloric Curves and Phase Transitions

Energy Technology Data Exchange (ETDEWEB)

Wang, J.; Hagel, K.; Ma, Y.; Murray, M.; Natowitz, J.; Wada, R.; Kowalski, S.; Materna, T.; Keksis, A.; Makeev, A.; Martin, E.; Qin, L.; Veselsky, M.; Ruangma, A.; Shetty, D.V.; Souliotis, G.; Winchester, E.M.; Yennello, S.J. [Cyclotron Institute, TAMU, College Station (TX) (United States); Cinausero, M.; Prete, E.G.; Fioretton, E. [INFN, Laboratori Nazionali di Legnaro, Legnaro (Italy); Fabris, D.; Lunardon, M.; Nebbia, G.; Rizzi, V.; Viesti, G. [INFN and Dipartimento di Fisica dell' Universita di Padova, Padova (Italy); Majka, Z.; Cibor, J.; Staszel, P. [Jagellonian University, M Smoluchowski Institute of Physics, Krakow (Poland); Martinez-Davalos, R.A.; Menchaca-Rocha, A.; Alfarro, R. [Instituto de Fisica, UNAM, Mexico City (Mexico); Keutgen, T.; El Masri, Y. [Universite Catholique de Louvain, FNRS and IPN, Louvain-Neuve (Belgium)

2003-07-01

A status report on some experiments designed to probe the dynamic evolution, the degree of equilibration and disassembly modes of hot composite nuclei produced in Fermi energy heavy ion collisions is presented. (authors)

Intermodal Storage and Transport Frame (ISTF) MIL-STD-1660 Design Criteria for Ammunition Unit Loads Tests

National Research Council Canada - National Science Library

Barickman, Philip

2004-01-01

.... The ISTF was evaluated by the testing procedures set forth in MIL-STD-1660. Stacking, vibration, edgewise rotational drop, incline impact, sling compatibility, forklifting, and disassembly testing were conducted on the ISTF units...

State-to-state and state-to-all-states reactive scattering angular distributions: F+H 2→HF+H

International Nuclear Information System (INIS)

Emmons, R.W.; Suck, S.H.

1983-01-01

How each state-to-state reactive transition determines nonundulatory ''state-to-all-states'' angular distribution has not yet been investigated. Here we present a complete exposure of state-to-state distorted-wave Born-approximation angular distributions in order to examine how the nonoscillatory and backward-peaked state-to-all-states reactive scattering angular distribution occurs

Development of decontamination technology for the decommissioned Bohunice A-1 nuclear power plant

International Nuclear Information System (INIS)

Krejci, F.; Majersky, D.; Solcanyi, M.; Sekely, S.; Kucharik, D.

1991-01-01

The main results of investigation into the decontamination technology for the equipment and buildings of the decommissioned A-1 nuclear power plant, achieved by the Nuclear Power Plants Research Institute in Trnava over the 1988-1990 period, are summarized. Mobile decontamination and recirculation equipment has been developed for pre-disassembling decontamination. A solution containing formic acid (19 g/l), EDTA-Na 4 (6 g/l) and thiourea (0.5 g/l) was used for decontamination of low-alloy steels; for materials from the steam generators and turbo-compressors, the decontamination factor (DF) of this solution was 30 to 150 per decontamination cycle. For high-alloy steels, a two-stage process comprising the use of an oxidation solution and a reduction solution appeared suitable. The oxidation solution contained potassium permanganate (0.6 g/l) and nitric acid (0.4 g/l), whereas the reduction solution, viz. Citrox 21, contained citric acid (0.5 g/l), oxalic acid (1.0 g/l) and EDTA-NA 4 (2.5 g/l). The DF is 10 to 50 in one oxidation-reduction cycle and 50-100 in two cycles. For the post-disassembling chemical decontamination, the contaminated material was cut into pieces 70 to 80 cm long, freed from grease and decontaminated chemically by submerging in the solution while applying treatment by ultrasound. A technology of electrochemical decontamination has also been developed. It appeared particularly suitable for structural materials of the primary coolant circuit comprising austenitic stainless steels and low-alloy steels after pre-disassembling chemical decontamination with remainders of the corrosion layer, and for structural materials of the secondary coolant circuit after chemical post-disassembling decontamination. Research in the field of decontamination of the building parts and of the outer surfaces of the structural materials concentrated mainly on the use of decontamination foams. Foaming solutions have been developed for the decontamination of PESL floors and

The function of Shp2 tyrosine phosphatase in the dispersal of acetylcholine receptor clusters

Directory of Open Access Journals (Sweden)

Madhavan Raghavan

2008-07-01

Full Text Available Abstract Background A crucial event in the development of the vertebrate neuromuscular junction (NMJ is the postsynaptic enrichment of muscle acetylcholine (ACh receptors (AChRs. This process involves two distinct steps: the local clustering of AChRs at synapses, which depends on the activation of the muscle-specific receptor tyrosine kinase MuSK by neural agrin, and the global dispersal of aneural or "pre-patterned" AChR aggregates, which is triggered by ACh or by synaptogenic stimuli. We and others have previously shown that tyrosine phosphatases, such as the SH2 domain-containing phosphatase Shp2, regulate AChR cluster formation in muscle cells, and that tyrosine phosphatases also mediate the dispersal of pre-patterned AChR clusters by synaptogenic stimuli, although the specific phosphatases involved in this latter step remain unknown. Results Using an assay system that allows AChR cluster assembly and disassembly to be studied separately and quantitatively, we describe a previously unrecognized role of the tyrosine phosphatase Shp2 in AChR cluster disassembly. Shp2 was robustly expressed in embryonic Xenopus muscle in vivo and in cultured myotomal muscle cells, and treatment of the muscle cultures with an inhibitor of Shp2 (NSC-87877 blocked the dispersal of pre-patterned AChR clusters by synaptogenic stimuli. In contrast, over-expression in muscle cells of either wild-type or constitutively active Shp2 accelerated cluster dispersal. Significantly, forced expression in muscle of the Shp2-activator SIRPα1 (signal regulatory protein α1 also enhanced the disassembly of AChR clusters, whereas the expression of a truncated SIRPα1 mutant that suppresses Shp2 signaling inhibited cluster disassembly. Conclusion Our results suggest that Shp2 activation by synaptogenic stimuli, through signaling intermediates such as SIRPα1, promotes the dispersal of pre-patterned AChR clusters to facilitate the selective accumulation of AChRs at developing NMJs.

Architecture of the RNA polymerase II-Mediator core initiation complex.

Science.gov (United States)

Plaschka, C; Larivière, L; Wenzeck, L; Seizl, M; Hemann, M; Tegunov, D; Petrotchenko, E V; Borchers, C H; Baumeister, W; Herzog, F; Villa, E; Cramer, P

2015-02-19

The conserved co-activator complex Mediator enables regulated transcription initiation by RNA polymerase (Pol) II. Here we reconstitute an active 15-subunit core Mediator (cMed) comprising all essential Mediator subunits from Saccharomyces cerevisiae. The cryo-electron microscopic structure of cMed bound to a core initiation complex was determined at 9.7 Å resolution. cMed binds Pol II around the Rpb4-Rpb7 stalk near the carboxy-terminal domain (CTD). The Mediator head module binds the Pol II dock and the TFIIB ribbon and stabilizes the initiation complex. The Mediator middle module extends to the Pol II foot with a 'plank' that may influence polymerase conformation. The Mediator subunit Med14 forms a 'beam' between the head and middle modules and connects to the tail module that is predicted to bind transcription activators located on upstream DNA. The Mediator 'arm' and 'hook' domains contribute to a 'cradle' that may position the CTD and TFIIH kinase to stimulate Pol II phosphorylation.

Mediator Undergoes a Compositional Change during Transcriptional Activation.

Science.gov (United States)

Petrenko, Natalia; Jin, Yi; Wong, Koon Ho; Struhl, Kevin

2016-11-03

Mediator is a transcriptional co-activator recruited to enhancers by DNA-binding activators, and it also interacts with RNA polymerase (Pol) II as part of the preinitiation complex (PIC). We demonstrate that a single Mediator complex associates with the enhancer and core promoter in vivo, indicating that it can physically bridge these transcriptional elements. However, the Mediator kinase module associates strongly with the enhancer, but not with the core promoter, and it dissociates from the enhancer upon depletion of the TFIIH kinase. Severing the kinase module from Mediator by removing the connecting subunit Med13 does not affect Mediator association at the core promoter but increases occupancy at enhancers. Thus, Mediator undergoes a compositional change in which the kinase module, recruited via Mediator to the enhancer, dissociates from Mediator to permit association with Pol II and the PIC. As such, Mediator acts as a dynamic bridge between the enhancer and core promoter. Copyright © 2016 Elsevier Inc. All rights reserved.

Transcription initiation complex structures elucidate DNA opening.

Science.gov (United States)

Plaschka, C; Hantsche, M; Dienemann, C; Burzinski, C; Plitzko, J; Cramer, P

2016-05-19

Transcription of eukaryotic protein-coding genes begins with assembly of the RNA polymerase (Pol) II initiation complex and promoter DNA opening. Here we report cryo-electron microscopy (cryo-EM) structures of yeast initiation complexes containing closed and open DNA at resolutions of 8.8 Å and 3.6 Å, respectively. DNA is positioned and retained over the Pol II cleft by a network of interactions between the TATA-box-binding protein TBP and transcription factors TFIIA, TFIIB, TFIIE, and TFIIF. DNA opening occurs around the tip of the Pol II clamp and the TFIIE 'extended winged helix' domain, and can occur in the absence of TFIIH. Loading of the DNA template strand into the active centre may be facilitated by movements of obstructing protein elements triggered by allosteric binding of the TFIIE 'E-ribbon' domain. The results suggest a unified model for transcription initiation with a key event, the trapping of open promoter DNA by extended protein-protein and protein-DNA contacts.

Conserved XPB Core Structure and Motifs for DNA Unwinding:Implications for Pathway Selection of Transcription or ExcisionRepair

Energy Technology Data Exchange (ETDEWEB)

Fan, Li; Arval, Andrew S.; Cooper, Priscilla K.; Iwai, Shigenori; Hanaoka, Fumio; Tainer, John A.

2005-04-01

The human xeroderma pigmentosum group B (XPB) helicase is essential for transcription, nucleotide excision repair, and TFIIH functional assembly. Here, we determined crystal structures of an Archaeoglobus fulgidus XPB homolog (AfXPB) that characterize two RecA-like XPB helicase domains and discover a DNA damage recognition domain (DRD), a unique RED motif, a flexible thumb motif (ThM), and implied conformational changes within a conserved functional core. RED motif mutations dramatically reduce helicase activity, and the DRD and ThM, which flank the RED motif, appear structurally as well as functionally analogous to the MutS mismatch recognition and DNA polymerase thumb domains. Substrate specificity is altered by DNA damage, such that AfXPB unwinds dsDNA with 3' extensions, but not blunt-ended dsDNA, unless it contains a lesion, as shown for CPD or (6-4) photoproducts. Together, these results provide an unexpected mechanism of DNA unwinding with Implications for XPB damage verification in nucleotide excision repair.

Composite Monopack for 120mm Mortar, With Plastic Pallet Adapters on a 42" x 53" Wooden Pallet, MIL-STD-1660 Tests, "Design Criteria for Ammunition Unit Loads", and Extreme Temperature Tests

National Research Council Canada - National Science Library

Dugan, Jeffery L

2005-01-01

.... The test units were tested in accordance with the procedures set forth in MIL-STD-1660. Stacking, repetitive shock, edgewise-rotational drop, incline-impact, forklifting, and disassembly testing were conducted on the test units...

State of the States

Science.gov (United States)

Journal of Education Finance, 2017

2017-01-01

In 2016, a group of school finance scholars and public school practitioners gathered in Jacksonville, Florida, for the National Education Finance Academy's annual conference to discuss, among an array of topics, the state of P-20 finance in all 50 states. At the roundtable discussion, 36 states were represented, and scholars representing 30 states…

A Parameter Study of Large Fast Reactor Nuclear Explosion Accidents

Energy Technology Data Exchange (ETDEWEB)

Wiesel, J R

1969-02-15

An IBM-code EEM (Explosive Excursion Model) has been developed for calculating the energy releases associated with the explosive disassembly of a large fast reactor following a superprompt critical condition. The assumed failure chain of events and the possible core collapse following a fuel meltdown give the input data and initial conditions, the most important of which is the reactivity insertion rate at the moment of the explosive core disassembly. The dependence of the energy releases on the reactivity insertion rate, the Doppler reactivity feedback, the power form factor and the core size have been studied. The model enables a quick estimation of conservative values of the destructive mechanical energy releases following a nuclear explosion and gives suggestions as to how to reduce or even avoid such excursions.

Fast Flux Test Facility interim examination and maintenance cell: Past, present, and future

International Nuclear Information System (INIS)

Vincent, J.R.

1990-09-01

The Fast Flux Test Facility Interim Examination and Maintenance Cell was designed to perform interim examination and/or disassembly of experimental core components for final analysis elsewhere, as well as maintenance of sodium-wetted or neutron-activated internal reactor parts and plant support hardware. The Interim Examination and Maintenance Cell equipment developed and used for the first ten years of operation has been primarily devoted to the disassembly and examination of core component test assemblies. While no major reactor equipment has required remote repair or maintenance, the Interim Examina Examination and Maintenance Cell has served as the remote repair facility for its own in-cell equipment, and several innovative remote repairs have been accomplished. The Interim Examination and Maintenance Cell's demonstrated versatility has shown its capability to support a challenging future. 12 refs., 9 figs

A Parameter Study of Large Fast Reactor Nuclear Explosion Accidents

International Nuclear Information System (INIS)

Wiesel, J.R.

1969-02-01

An IBM-code EEM (Explosive Excursion Model) has been developed for calculating the energy releases associated with the explosive disassembly of a large fast reactor following a superprompt critical condition. The assumed failure chain of events and the possible core collapse following a fuel meltdown give the input data and initial conditions, the most important of which is the reactivity insertion rate at the moment of the explosive core disassembly. The dependence of the energy releases on the reactivity insertion rate, the Doppler reactivity feedback, the power form factor and the core size have been studied. The model enables a quick estimation of conservative values of the destructive mechanical energy releases following a nuclear explosion and gives suggestions as to how to reduce or even avoid such excursions

A micromotor based on polymer single crystals and nanoparticles: toward functional versatility

Science.gov (United States)

Liu, Mei; Liu, Limei; Gao, Wenlong; Su, Miaoda; Ge, Ya; Shi, Lili; Zhang, Hui; Dong, Bin; Li, Christopher Y.

2014-07-01

We report a multifunctional micromotor fabricated by the self-assembly technique using multifunctional materials, i.e. polymer single crystals and nanoparticles, as basic building blocks. Not only can this micromotor achieve autonomous and directed movement, it also possesses unprecedented functions, including enzymatic degradation-induced micromotor disassembly, sustained release and molecular detection.We report a multifunctional micromotor fabricated by the self-assembly technique using multifunctional materials, i.e. polymer single crystals and nanoparticles, as basic building blocks. Not only can this micromotor achieve autonomous and directed movement, it also possesses unprecedented functions, including enzymatic degradation-induced micromotor disassembly, sustained release and molecular detection. Electronic supplementary information (ESI) available: Experimental section, Fig. S1-S8 and Video S1-S4. See DOI: 10.1039/c4nr02593h

Decommissioning? Why not use a robot

International Nuclear Information System (INIS)

Bares, L.C.

1995-01-01

Tasks which may be accomplished by robots alone or in conjunction with human workers in decommissioning nuclear facilities include: routine surveillance in contaminated areas; radiation surveys and sampling; preparation of work area; decontamination of walls and floors; disassembly of contaminated equipment and piping; internal decontamination of piping and waste storage/processing tanks; sorting materials; removal of large activated/contaminated structures; asbestos removal and packaging; transport of waste from disassembly areas; tending waste processing equipment; waste packaging for storage. The status of the technology is briefly reviewed and examples of the use of robots in decommissioning work in the USA are described. Although the use of robots in this field is not extensive so far, that use is increasing and information on its costs and benefits are becoming available. (UK)

Annular linear induction pump with an externally supported duct

International Nuclear Information System (INIS)

1980-01-01

An annular linear induction pump of increased efficiency is described, capable of being readily disassembled for repair or replacement of parts, and having one pass flow of the liquid metal through the pump. (U.K.)

Qualification Testing for Clipless Seal Used on 3/4 Banding, 40 in. x 48 in. Wood Pallet With .50 Caliber Ammunition in M2 Metal Boxes in Wire Bound Boxes IAW MIL-STD-1660, "Design Criteria for Ammunition Unit Loads"

National Research Council Canada - National Science Library

2006-01-01

...), from Independence, Missouri. Two test units were tested with a load of 4,200 lbs. each. The tests accomplished on the test units were the stacking, vibration, drop, incline impact, forklift handling, and disassembly tests...

Complexity of rice Hsp100 gene family: lessons from rice genome ...

Indian Academy of Sciences (India)

Madhu Sudhan

2007-03-29

Mar 29, 2007 ... Chaperonins are a class of molecular chaperones found in prokaryotes and in the ... Keywords. Chaperone, gene family, Hsp100, Oryza sativa ..... Sculpting the proteome with AAA+ proteases and disassembly machines; Cell ...

Quantum State Engineering Via Coherent-State Superpositions

Science.gov (United States)

Janszky, Jozsef; Adam, P.; Szabo, S.; Domokos, P.

1996-01-01

The quantum interference between the two parts of the optical Schrodinger-cat state makes possible to construct a wide class of quantum states via discrete superpositions of coherent states. Even a small number of coherent states can approximate the given quantum states at a high accuracy when the distance between the coherent states is optimized, e. g. nearly perfect Fock state can be constructed by discrete superpositions of n + 1 coherent states lying in the vicinity of the vacuum state.

Basis for Interim Operation for the K-Reactor in Cold Standby

Energy Technology Data Exchange (ETDEWEB)

Shedrow, B.

1998-10-19

The Basis for Interim Operation (BIO) document for K Reactor in Cold Standby and the L- and P-Reactor Disassembly Basins was prepared in accordance with the draft DOE standard for BIO preparation (dated October 26, 1993).

Self-assembled lipoprotein based gold nanoparticles for detection and photothermal disaggregation of β-amyloid aggregates

KAUST Repository

Martins, P. A. T.; Alsaiari, Shahad K.; Julfakyan, Khachatur; Nie, Z.; Khashab, Niveen M.

2017-01-01

We present a reconstituted lipoprotein-based nanoparticle platform comprising a curcumin fluorescent motif and an NIR responsive gold core. This multifunctional nanosystem is successfully used for aggregation-dependent fluorescence detection and photothermal disassembly of insoluble amyloid aggregates.

Self-assembled lipoprotein based gold nanoparticles for detection and photothermal disaggregation of β-amyloid aggregates

KAUST Repository

Martins, P. A. T.

2017-01-10

We present a reconstituted lipoprotein-based nanoparticle platform comprising a curcumin fluorescent motif and an NIR responsive gold core. This multifunctional nanosystem is successfully used for aggregation-dependent fluorescence detection and photothermal disassembly of insoluble amyloid aggregates.

Basis for Interim Operation for the K-Reactor in Cold Standby

International Nuclear Information System (INIS)

Shedrow, B.

1998-01-01

The Basis for Interim Operation (BIO) document for K Reactor in Cold Standby and the L- and P-Reactor Disassembly Basins was prepared in accordance with the draft DOE standard for BIO preparation (dated October 26, 1993)

Production of radioisotopic gamma radiation sources in JAERI

International Nuclear Information System (INIS)

Katoh, Hisashi; Kogure, Hiroto; Suzuki, Kyohei

1980-04-01

The present state of production of gamma radiation sources in Japan Atomic Energy Research Institute (JAERI) is described. Sources of 192 Ir, 60 Co and 170 Tm for industrial and 198 Au and 192 Ir for medical applications are produced and delivered routinely by JAERI. Prefabricated assembly targets are irradiated in JRR-2, JRR-3, JRR-4 or JMTR. The irradiated targets are disassembled in a heavy density concrete cave or a lead-shielded cell, depending on the level of radioactivity. The yield of radioactivity in each target is measured with the aid of an ionization chamber. Where necessary, irradiated targets are encapsulated hermetically in capsules of aluminium, stainless steel or other material. The yield of radioactivity is estimated in relation with the burn-up of target nuclide and product nuclide. (author)

Study on identification method of auto refurbishment test

Science.gov (United States)

Jiang, Zhenfei; Feng, Qingfu; Wang, Zhengyu; Jiang, Suqin; Chen, Xing; Zheng, Shaoyuan; Li, Bokui

2018-04-01

In recent years, a large number of refurbished cars inflow into the market as new cars. The traditional methods to identify refurbished cars are mostly based on experience, the subjectivity is too high and the credibility is low. In the production of automobile, the state and the automobile industry set clear standards for the thickness of the automobile paint. There is a big difference between the thickness of machine spraying and manual spraying. By studying this difference and combining with the standard, it can be identified accurately whether the car has been renovated; during the second assembly process, the surface of some parts (such as bolts) will have obvious signs of wear and tear due to the regular assembly and disassembly, it can also be identified accurately through the study of these assembly traces.

HBV core protein allosteric modulators differentially alter cccDNA biosynthesis from de novo infection and intracellular amplification pathways.

Science.gov (United States)

Guo, Fang; Zhao, Qiong; Sheraz, Muhammad; Cheng, Junjun; Qi, Yonghe; Su, Qing; Cuconati, Andrea; Wei, Lai; Du, Yanming; Li, Wenhui; Chang, Jinhong; Guo, Ju-Tao

2017-09-01

Hepatitis B virus (HBV) core protein assembles viral pre-genomic (pg) RNA and DNA polymerase into nucleocapsids for reverse transcriptional DNA replication to take place. Several chemotypes of small molecules, including heteroaryldihydropyrimidines (HAPs) and sulfamoylbenzamides (SBAs), have been discovered to allosterically modulate core protein structure and consequentially alter the kinetics and pathway of core protein assembly, resulting in formation of irregularly-shaped core protein aggregates or "empty" capsids devoid of pre-genomic RNA and viral DNA polymerase. Interestingly, in addition to inhibiting nucleocapsid assembly and subsequent viral genome replication, we have now demonstrated that HAPs and SBAs differentially modulate the biosynthesis of covalently closed circular (ccc) DNA from de novo infection and intracellular amplification pathways by inducing disassembly of nucleocapsids derived from virions as well as double-stranded DNA-containing progeny nucleocapsids in the cytoplasm. Specifically, the mistimed cuing of nucleocapsid uncoating prevents cccDNA formation during de novo infection of hepatocytes, while transiently accelerating cccDNA synthesis from cytoplasmic progeny nucleocapsids. Our studies indicate that elongation of positive-stranded DNA induces structural changes of nucleocapsids, which confers ability of mature nucleocapsids to bind CpAMs and triggers its disassembly. Understanding the molecular mechanism underlying the dual effects of the core protein allosteric modulators on nucleocapsid assembly and disassembly will facilitate the discovery of novel core protein-targeting antiviral agents that can more efficiently suppress cccDNA synthesis and cure chronic hepatitis B.

HBV core protein allosteric modulators differentially alter cccDNA biosynthesis from de novo infection and intracellular amplification pathways.

Directory of Open Access Journals (Sweden)

Fang Guo

2017-09-01

Full Text Available Hepatitis B virus (HBV core protein assembles viral pre-genomic (pg RNA and DNA polymerase into nucleocapsids for reverse transcriptional DNA replication to take place. Several chemotypes of small molecules, including heteroaryldihydropyrimidines (HAPs and sulfamoylbenzamides (SBAs, have been discovered to allosterically modulate core protein structure and consequentially alter the kinetics and pathway of core protein assembly, resulting in formation of irregularly-shaped core protein aggregates or "empty" capsids devoid of pre-genomic RNA and viral DNA polymerase. Interestingly, in addition to inhibiting nucleocapsid assembly and subsequent viral genome replication, we have now demonstrated that HAPs and SBAs differentially modulate the biosynthesis of covalently closed circular (ccc DNA from de novo infection and intracellular amplification pathways by inducing disassembly of nucleocapsids derived from virions as well as double-stranded DNA-containing progeny nucleocapsids in the cytoplasm. Specifically, the mistimed cuing of nucleocapsid uncoating prevents cccDNA formation during de novo infection of hepatocytes, while transiently accelerating cccDNA synthesis from cytoplasmic progeny nucleocapsids. Our studies indicate that elongation of positive-stranded DNA induces structural changes of nucleocapsids, which confers ability of mature nucleocapsids to bind CpAMs and triggers its disassembly. Understanding the molecular mechanism underlying the dual effects of the core protein allosteric modulators on nucleocapsid assembly and disassembly will facilitate the discovery of novel core protein-targeting antiviral agents that can more efficiently suppress cccDNA synthesis and cure chronic hepatitis B.

HBV core protein allosteric modulators differentially alter cccDNA biosynthesis from de novo infection and intracellular amplification pathways

Science.gov (United States)

Guo, Fang; Zhao, Qiong; Cheng, Junjun; Qi, Yonghe; Su, Qing; Wei, Lai; Li, Wenhui; Chang, Jinhong

2017-01-01

Hepatitis B virus (HBV) core protein assembles viral pre-genomic (pg) RNA and DNA polymerase into nucleocapsids for reverse transcriptional DNA replication to take place. Several chemotypes of small molecules, including heteroaryldihydropyrimidines (HAPs) and sulfamoylbenzamides (SBAs), have been discovered to allosterically modulate core protein structure and consequentially alter the kinetics and pathway of core protein assembly, resulting in formation of irregularly-shaped core protein aggregates or “empty” capsids devoid of pre-genomic RNA and viral DNA polymerase. Interestingly, in addition to inhibiting nucleocapsid assembly and subsequent viral genome replication, we have now demonstrated that HAPs and SBAs differentially modulate the biosynthesis of covalently closed circular (ccc) DNA from de novo infection and intracellular amplification pathways by inducing disassembly of nucleocapsids derived from virions as well as double-stranded DNA-containing progeny nucleocapsids in the cytoplasm. Specifically, the mistimed cuing of nucleocapsid uncoating prevents cccDNA formation during de novo infection of hepatocytes, while transiently accelerating cccDNA synthesis from cytoplasmic progeny nucleocapsids. Our studies indicate that elongation of positive-stranded DNA induces structural changes of nucleocapsids, which confers ability of mature nucleocapsids to bind CpAMs and triggers its disassembly. Understanding the molecular mechanism underlying the dual effects of the core protein allosteric modulators on nucleocapsid assembly and disassembly will facilitate the discovery of novel core protein-targeting antiviral agents that can more efficiently suppress cccDNA synthesis and cure chronic hepatitis B. PMID:28945802

Energy impacts of recycling disassembly material in residential buildings

International Nuclear Information System (INIS)

Gao, Weijun; Ariyama, Takahiro; Ojima, Toshio; Meier, Alan

2000-01-01

In order to stop the global warmth due to the CO2 concentration, the energy use should be decreased. The investment of building construction industry in Japan is about 20 percent of GDP. This fraction is much higher than in most developed countries. That results the Japanese building construction industry including residential use consumes about one third of all energy and resources of the entire industrial sectors. In order to save energy as well as resource, the recycle of the building materials should be urgent to be carried out. In this paper, we focus on the potential energy savings with a simple calculated method when the building materials or products are manufactured from recycled materials. We examined three kinds of residential buildings with different construction techniques and estimated the decreased amount of energy consumption and resources resulting from use of recycled materials. The results have shown for most building materials, the energy consumption needed to remake housing materials from recycled materials is lower than that to make new housing materials. The energy consumption of building materials in all case-study housing can be saved by at least 10 percent. At the same time, the resource, measured by mass of building materials (kg) can be decreased by over 50 percent

Shape Formation by Self-Disassembly in Programmable Matter Systems

Science.gov (United States)

2012-06-01

classifying modular robotic systems by the geometry of the system: chain, lattice, truss, or free form. For a more detailed history of the modular...Both the source and destination of a UDP packet are specified by a address/port pair. An address is a typical IPv4 address such as 18.70.0.160 while a... IPv4 network, the simulated modules can be located on any machine that is connected to the network. If the user wants to simulate a large system, it

Method of assembling and disassembling a control component structure

International Nuclear Information System (INIS)

Edwards, G.T.; Schluderberg, D.C.

1982-01-01

A technique is provided for engaging and disengaging burnable poison rods from the spider in a fuel assembly. The cap on the end of each of the burnable poison rods is provided with a shank that is received in the respective bore formed in the spider. A frangible flange secures the shank and rod to the spider. Pressing the shank in the direction of the bore axis ruptures the frangible flange to release the rod from the spider

7 CFR 1220.615 - State and United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false State and United States. 1220.615 Section 1220.615... CONSUMER INFORMATION Procedures To Request a Referendum Definitions § 1220.615 State and United States. State and United States include the 50 States of the United States of America, the District of Columbia...

7 CFR 1220.129 - State and United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false State and United States. 1220.129 Section 1220.129... CONSUMER INFORMATION Soybean Promotion and Research Order Definitions § 1220.129 State and United States. The terms State and United States include the 50 States of the United States of America, the District...

7 CFR 1209.21 - State and United States.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false State and United States. 1209.21 Section 1209.21... Definitions § 1209.21 State and United States. (a) State means any of the several States, the District of Columbia, and the Commonwealth of Puerto Rico. (b) United States means collectively the several States of...

The Potential of Circular Economy in Sustainable Buildings

DEFF Research Database (Denmark)

Malabi Larsen, Leonora Charlotte; Birgisdottir, Harpa; Birkved, Morten

2018-01-01

benefits of designing the buildings concrete structure for disassembly, with the purpose of reuse, as well as to exemplify how circular economy can be applied in future building projects. Moreover, the paper aims at suggesting a more industry focused approach towards circular economy in order to seize...... the inherent potentials. As a result, it was found that recycling and energy recovery are the most common circular economy practices in the building industry, even though the economic and environmental benefits of reuse are believed to be much higher. This observation is supported by the findings of the case...... and glass, thereby enabling easier disassembly for both reuse and recycling. However, main challenges preventing the industry from seizing these potentials are identified as: focus on short term goals, complex supply chains, lack of collaboration between stakeholders and absence of a commonly agreed...

Decommissioning of an Irradiator MPX-γ - 25M and a neutron Irradiator

International Nuclear Information System (INIS)

Soguero, Dania; Guerra, Mercedes; Prieto, Enrique; Desdin, Luis

2013-01-01

In this paper a technology is developed with its procedures in radiation protection to ensure the safety of the process of decommissioning of two irradiators. Both processes are described, the process of decommissioning of a neutron Irradiator 4. 44·10 11 Bq, employed in the vegetal radio mutagenesis, and disassembling of an installation of gamma irradiation of 3.33 * 10 12 Bq, self-shielded of category I, model MPX - γ - 25 M. The specific objectives are: a) identify aspects of the contractual assurance, of human and technical resources, b) to evaluate the radiological situation of the process and c) analyze the potential radiological extraordinary events in each of the steps of the process, ensuring the right answers. Evaluation of radiological successful events described can be considered as reference to address the process of disassembling of other similar irradiators

Decommissioning of an Irradiator MPX-{gamma} - 25M and a neutron Irradiator; Desmantelamiento de un irradiador tipo MPX-{gamma}-25M y de un irradiador de neutrones

Energy Technology Data Exchange (ETDEWEB)

Soguero, Dania; Guerra, Mercedes; Prieto, Enrique; Desdin, Luis, E-mail: sdania@ceaden.edu.cu [Centro de Aplicaciones Tecnologica y Desarrollo Nuclear (CEADEN), La Habana (Cuba)

2013-07-01

In this paper a technology is developed with its procedures in radiation protection to ensure the safety of the process of decommissioning of two irradiators. Both processes are described, the process of decommissioning of a neutron Irradiator 4. 44{center_dot}10{sup 11}Bq, employed in the vegetal radio mutagenesis, and disassembling of an installation of gamma irradiation of 3.33 * 10{sup 12} Bq, self-shielded of category I, model MPX - {gamma} - 25 M. The specific objectives are: a) identify aspects of the contractual assurance, of human and technical resources, b) to evaluate the radiological situation of the process and c) analyze the potential radiological extraordinary events in each of the steps of the process, ensuring the right answers. Evaluation of radiological successful events described can be considered as reference to address the process of disassembling of other similar irradiators.

NEDDylation promotes stress granule assembly.

Science.gov (United States)

Jayabalan, Aravinth Kumar; Sanchez, Anthony; Park, Ra Young; Yoon, Sang Pil; Kang, Gum-Yong; Baek, Je-Hyun; Anderson, Paul; Kee, Younghoon; Ohn, Takbum

2016-07-06

Stress granules (SGs) harbour translationally stalled messenger ribonucleoproteins and play important roles in regulating gene expression and cell fate. Here we show that neddylation promotes SG assembly in response to arsenite-induced oxidative stress. Inhibition or depletion of key components of the neddylation machinery concomitantly inhibits stress-induced polysome disassembly and SG assembly. Affinity purification and subsequent mass-spectrometric analysis of Nedd8-conjugated proteins from translationally stalled ribosomal fractions identified ribosomal proteins, translation factors and RNA-binding proteins (RBPs), including SRSF3, a previously known SG regulator. We show that SRSF3 is selectively neddylated at Lys85 in response to arsenite. A non-neddylatable SRSF3 (K85R) mutant do not prevent arsenite-induced polysome disassembly, but fails to support the SG assembly, suggesting that the neddylation pathway plays an important role in SG assembly.

Remote maintenance ''lessons learned'' on prototypical reprocessing equipment

International Nuclear Information System (INIS)

Kring, C.T.; Schrock, S.L.

1990-01-01

Hardware representative of essentially every major equipment item necessary for reprocessing breeder reactor nuclear fuel has been installed and tested for remote maintainability. This testing took place in a cold mock-up of a remotely maintained hot cell operated by the Consolidated Fuel Reprocessing Program (CFRP) within the Fuel Recycle Division at Oak Ridge National Laboratory (ORNL). The reprocessing equipment tested included a Disassembly System, a Shear System, a Dissolver System, an Automated Sampler System, removable Equipment Racks on which various chemical process equipment items were mounted, and an advanced servomanipulator (ASM). These equipment items were disassembled and reassembled remotely by using the remote handling systems that are available within the cold mock-up area. This paper summarizes the ''lessons learned'' as a result of the numerous maintenance activities associated with each of these equipment items. 4 refs., 3 figs., 1 tab

Optimal resource states for local state discrimination

Science.gov (United States)

Bandyopadhyay, Somshubhro; Halder, Saronath; Nathanson, Michael

2018-02-01

We study the problem of locally distinguishing pure quantum states using shared entanglement as a resource. For a given set of locally indistinguishable states, we define a resource state to be useful if it can enhance local distinguishability and optimal if it can distinguish the states as well as global measurements and is also minimal with respect to a partial ordering defined by entanglement and dimension. We present examples of useful resources and show that an entangled state need not be useful for distinguishing a given set of states. We obtain optimal resources with explicit local protocols to distinguish multipartite Greenberger-Horne-Zeilinger and graph states and also show that a maximally entangled state is an optimal resource under one-way local operations and classical communication to distinguish any bipartite orthonormal basis which contains at least one entangled state of full Schmidt rank.

Geometry sensing by dendritic cells dictates spatial organization and PGE(2)-induced dissolution of podosomes.

NARCIS (Netherlands)

Dries, K. van den; Helden, S.F.G. van; Riet, J.T. te; Diez-Ahedo, R.; Manzo, C.; Oud, M.M.; Leeuwen, F.N. van; Brock, R.E.; Garcia-Parajo, M.F.; Cambi, A.; Figdor, C.G.

2012-01-01

Assembly and disassembly of adhesion structures such as focal adhesions (FAs) and podosomes regulate cell adhesion and differentiation. On antigen-presenting dendritic cells (DCs), acquisition of a migratory and immunostimulatory phenotype depends on podosome dissolution by prostaglandin E(2)

Engineering Evaluation Tests of 16 Gauge vs 14 Gauge Staples IAW MIL-STD-1660, 40MM Cartridge on Wooden Pallet

National Research Council Canada - National Science Library

Dugan, Jeffery L

2008-01-01

.... Three test units were tested with a load of 2,290 lbs, 2,295 lbs, and 2,295 lbs. The testing accomplished on the test units was the Stacking, Repetitive Shock, Drop, Incline-Impact, Forklifting, and Disassembly Tests. Test Units #1...

Backbone Diversity Analysis in Catalyst Design

NARCIS (Netherlands)

Maldonado, A.G.; Hageman, J.A.; Mastroianni, S.; Rothenberg, G.

2009-01-01

We present a computer-based heuristic framework for designing libraries of homogeneous catalysts. In this approach, a set of given bidentate ligand-metal complexes is disassembled into key substructures (building blocks). These include metal atoms, ligating groups, backbone groups, and residue

Preliminary analysis of the transient overpower accident for CRBRP. Final report

International Nuclear Information System (INIS)

Kastenberg, W.E.; Frank, M.V.

1975-07-01

A preliminary analysis of the transient overpower accident for the Clinch River Breeder Reactor Plant (CRBRP) is presented. Several uncertainties in the analysis and the estimation of ramp rates during the transition to disassembly are discussed. The major conclusions are summarized

7 CFR 1767.20 - Plant accounts.

Science.gov (United States)

2010-01-01

... line wholly identified with items included herein. 11. Retaining walls. 12. Water conductors and... settings, water walls, arches, grates, insulation, blowdown system, drying out of new boilers, also... disassembly machinery. 12. Reactor fuel element failure detection system. 13. Reactor emergency poison...

Sports Management for Sports Massification Planned and Executed by Social Organizations. Critics to Models, Experiences and Proposal Methodological Accompaniment

Directory of Open Access Journals (Sweden)

Lorenza Antonia Reyes de Duran

2016-08-01

Full Text Available The proposal analysis, interpretation, disassembly, self-criticism and guidance is born and comes from work experience planned mass sports and social organizations opposed-not in the conventional sense comparative-private business models and sport, state and management. The contribution made by the sports management experience from positions of power, either state or business are undeniable and its impact is difficult to express in numbers for its humanistic value, which is incalculable. However, it is urgent to emphasize the products and results achieved by some social organizations related to sport; as are the reference cases in Higuerón and the municipality Independence of Yaracuy state. From a dialectical analysis of reality, we try to understand the complex system that involves high-level sports management and performance, we introduce in the praxical notions of sporting activity and associated approach applied to social and community work. As opening and closing action research processes, we will make a proposal to accompany sports management concerning overcrowding by and from social organizations. This proposal is constructed from an innovative, flexible, open, inclusive and social, community and organizational curriculum relevance.

Minimally conscious state or cortically mediated state?

Science.gov (United States)

Naccache, Lionel

2018-04-01

Durable impairments of consciousness are currently classified in three main neurological categories: comatose state, vegetative state (also recently coined unresponsive wakefulness syndrome) and minimally conscious state. While the introduction of minimally conscious state, in 2002, was a major progress to help clinicians recognize complex non-reflexive behaviours in the absence of functional communication, it raises several problems. The most important issue related to minimally conscious state lies in its criteria: while behavioural definition of minimally conscious state lacks any direct evidence of patient's conscious content or conscious state, it includes the adjective 'conscious'. I discuss this major problem in this review and propose a novel interpretation of minimally conscious state: its criteria do not inform us about the potential residual consciousness of patients, but they do inform us with certainty about the presence of a cortically mediated state. Based on this constructive criticism review, I suggest three proposals aiming at improving the way we describe the subjective and cognitive state of non-communicating patients. In particular, I present a tentative new classification of impairments of consciousness that combines behavioural evidence with functional brain imaging data, in order to probe directly and univocally residual conscious processes.

From Centralized Disassembly to Life Cycle Management: Status and Progress of E-waste Treatment System in China

Science.gov (United States)

Song, Xiaolong; Yang, Jianxin; Lu, Bin; Yang, Dong

2017-01-01

China is now facing e-waste problems from both growing domestic generation and illegal imports. Many stakeholders are involved in the e-waste treatment system due to the complexity of e-waste life cycle. Beginning with the state of the e-waste treatment industry in China, this paper summarizes the latest progress in e-waste management from such aspects as the new edition of the China RoHS Directive, new Treatment List, new funding subsidy standard, and eco-design pilots. Thus, a conceptual model for life cycle management of e-waste is generalized. The operating procedure is to first identify the life cycle stages of the e-waste and extract the important life cycle information. Then, life cycle tools can be used to conduct a systematic analysis to help decide how to maximize the benefits from a series of life cycle engineering processes. Meanwhile, life cycle thinking is applied to improve the legislation relating to e-waste so as to continuously improve the sustainability of the e-waste treatment system. By providing an integrative framework, the life cycle management of e-waste should help to realize sustainable management of e-waste in developing countries.

State laws on tobacco control--United States, 1998.

Science.gov (United States)

Fishman, J A; Allison, H; Knowles, S B; Fishburn, B A; Woollery, T A; Marx, W T; Shelton, D M; Husten, C G; Eriksen, M P

1999-06-25

State laws addressing tobacco use, the leading preventable cause of death in the United States, are summarized. Laws address smoke-free indoor air, minors' access to tobacco products, advertising of tobacco products, and excise taxes on tobacco products. Legislation effective through December 31, 1998. CDC identified laws addressing tobacco control by using an on-line legal research database. CDC's findings were verified with the National Cancer Institute's State Cancer Legislative Database. Since a previous surveillance summary on state tobacco-control laws published in November 1995 (covering legislation effective through June 30, 1995), several states have enacted new restrictions or strengthened existing legislation that addresses smoke-free indoor air, minors' access to tobacco, tobacco advertising, and tobacco taxes. Five states strengthened their smoke-free indoor air legislation. All states and Washington, D.C., continued to prohibit the sale and distribution of tobacco products to minors; however, 21 states expanded minors' access laws by designating enforcement authorities, adding license suspension or revocation for sale to minors, or requiring signage. Since the 1995 report, eight additional states (a total of 19 states and Washington, D.C.) now ban vending machines from areas accessible to minors. Thirteen states restrict advertising of tobacco products, an increase of four states since the 1995 report. Although the number of states that tax cigarettes and smokeless tobacco did not change, 13 states increased excise taxes on cigarettes, and five states increased excise taxes on smokeless tobacco products. The average state excise tax on cigarettes is 38.9 cents per pack, an increase of 7.4 cents compared with the average tax in the 1995 report. State laws addressing tobacco control vary in relation to restrictiveness, enforcement and penalties, preemptions, and exceptions. The data summarizing state tobacco-control laws are available through CDC

The Presynaptic v-ATPase Reversibly Disassembles and Thereby Modulates Exocytosis but Is Not Part of the Fusion Machinery

Directory of Open Access Journals (Sweden)

Anna Bodzęta

2017-08-01

Full Text Available Vacuolar H+-ATPase (v-ATPase is a multi-subunit complex comprising two domains: the cytosolic V1 domain catalyzing ATP hydrolysis and the membranous V0 sector translocating protons across membranes. In addition to proton pumping, a direct function of the V0 proteolipid ring in membrane fusion has been proposed for yeast vacuolar fusion and synaptic vesicle exocytosis in Drosophila. Here, we show in cultured hippocampal neurons that in recycling synaptic vesicles, v-ATPases are only transiently assembled in a pH-dependent fashion during the tightly coupled cycle of exo-endocytosis. Upon locking v-ATPase in an assembled state by saliphenylhalamide, we observed use- and time-dependent release depression for stimuli exceeding release of primed vesicles but no abrogation of exocytosis. Thus, the membranous V0 sector is not part of the exocytotic fusion machinery. Instead, v-ATPase modulates release upstream of docking to favor fusion of fully filled synaptic vesicles.

76 FR 51879 - Definition of Solid Waste Disposal Facilities for Tax-Exempt Bond Purposes

Science.gov (United States)

2011-08-19

... generation, purchase or acquisition into a qualified solid waste disposal process described in paragraph (d... purchases used cars and restores them. This restoration process includes disassembly, cleaning, and... regulations by this Treasury decision (the Final Regulations). Significant aspects of the public comments and...

Golgi twins in late mitosis revealed by genetically encoded tags for live cell imaging and correlated electron microscopy

NARCIS (Netherlands)

Gaietta, Guido M; Giepmans, Ben N G; Deerinck, Thomas J; Smith, W Bryan; Ngan, Lucy; Llopis, Juan; Adams, Stephen R; Tsien, Roger Y; Ellisman, Mark H

2006-01-01

Combinations of molecular tags visible in light and electron microscopes become particularly advantageous in the analysis of dynamic cellular components like the Golgi apparatus. This organelle disassembles at the onset of mitosis and, after a sequence of poorly understood events, reassembles after

48 CFR 227.7103-7 - Use and non-disclosure agreement.

Science.gov (United States)

2010-10-01

... recipient shall not, for example, enhance, decompile, disassemble, or reverse engineer the software; time... (b) of this subsection, technical data or computer software delivered to the Government with..., display, or disclose technical data subject to limited rights or computer software subject to restricted...

Size control and surface functionalization of multivalent non-covalent and porous nanomaterials

NARCIS (Netherlands)

Weinhart-Mejia, R.

2015-01-01

The use of nanomaterials for molecular imaging and therapeutics has flourished over the past decade. Controlled assembly and disassembly of nanoparticles is important for applications such as drug delivery systems in order to tune their loading and unloading behavior. Such properties can be

14 CFR 382.129 - What other requirements apply when passengers' wheelchairs, other mobility aids, and other...

Science.gov (United States)

2010-01-01

... passengers' wheelchairs, other mobility aids, and other assistive devices must be disassembled for stowage... Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive Devices § 382.129 What other requirements apply when passengers' wheelchairs, other mobility aids, and other assistive devices must be...

Abrasive water jet cutting

International Nuclear Information System (INIS)

Leist, K.J.; Funnell, G.J.

1988-01-01

In the process of selecting a failed equipment cut-up tool for the process facility modifications (PFM) project, a system using an abrasive water jet (AWJ) was developed and tested for remote disassembly of failed equipment. It is presented in this paper

PCNA Loading by RFC, Mechanism of

KAUST Repository

Oke, Muse; Zaher, Manal S.; Hamdan, Samir

2018-01-01

Replicative polymerases achieve highly processive DNA synthesis by binding to a clamp-like processivity factor that is topologically linked to DNA. The eukaryotic processivity clamp, proliferating cell nuclear antigen (PCNA), exists mostly as a closed ring in solution. Replication factor C (RFC), a five-subunit ATP-dependent protein complex, mediates PCNA opening in solution (assembly stage) and closing onto the primer-template (disassembly stage). In the assembly stage, RFC binding to ATP causes conformational changes that trigger RFC to form a complex with PCNA. PCNA is then cracked open at one subunit interface, and both RFC and PCNA adopt an extended spiral structure with a chamber that selects for a primer-template DNA structure. Binding of RFC/PCNA to DNA triggers the disassembly stage by stimulating ATP hydrolysis. Subsequent conformational changes in RFC and PCNA lead to the closing of PCNA onto the primer-template and the dissociation of RFC.

KEY INTERACTIONS FOR CLATHRIN COAT STABILITY

Science.gov (United States)

Böcking, Till; Aguet, Francois; Rapoport, Iris; Banzhaf, Manuel; Yu, Anan; Zeeh, Jean Christophe; Kirchhausen, Tom

2014-01-01

SUMMARY Clathrin-coated vesicles are major carriers of vesicular traffic in eukaryotic cells. This endocytic pathway relies on cycles of clathrin coat assembly and Hsc70-mediated disassembly. Here we identify histidine residues as major determinants of lattice assembly and stability. They are located at the invariant interface between the proximal and distal segments of clathrin heavy chains, in triskelions centered on two adjacent vertices of the coated-vesicle lattice. Mutation of these histidine to glutamine alters the pH dependence of coat stability. We then describe single-particle fluorescence imaging experiments in which we follow the effect of these histidine mutations on susceptibility to Hsc70-dependent uncoating. Coats destabilized by these mutations require fewer Hsc70 molecules to initiate disassembly as predicted by a model in which Hsc70 traps conformational distortions during the auxilin- and Hsc70:ATP-mediated uncoating reaction. PMID:24815030

Transition phase in LMFBR hypothetical accidents

International Nuclear Information System (INIS)

Ostensen, R.W.; Henninger, R.J.; Jackson, J.F.

1976-01-01

Mechanistic analyses of transient-under-cooling accidents have led in some cases to a mild initiating phase instead of a direct hydrodynamic disassembly of the core. The fuel is then trapped in the core by the strong mechanical surroundings and blockages formed by refrozen cladding steel and/or fuel. The formation of fuel blockages has been verified experimentally. The bottled-up core will boil on fission and decay heat, with steel as the working fluid. Boil-up in a churn turbulent flow regime may prevent recriticality due to fuel recompaction. Ultimate fuel removal from the core is probably by a two-phase blow-down after permanent leakage paths are opened. However, a vigorous recriticality can not be precluded. Reactors with void coefficients larger than that in CRBR are more likely to disassemble in the initiating phase, so the transition phase may be unique to small cores

Reconfigurable engineered motile semiconductor microparticles.

Science.gov (United States)

Ohiri, Ugonna; Shields, C Wyatt; Han, Koohee; Tyler, Talmage; Velev, Orlin D; Jokerst, Nan

2018-05-03

Locally energized particles form the basis for emerging classes of active matter. The design of active particles has led to their controlled locomotion and assembly. The next generation of particles should demonstrate robust control over their active assembly, disassembly, and reconfiguration. Here we introduce a class of semiconductor microparticles that can be comprehensively designed (in size, shape, electric polarizability, and patterned coatings) using standard microfabrication tools. These custom silicon particles draw energy from external electric fields to actively propel, while interacting hydrodynamically, and sequentially assemble and disassemble on demand. We show that a number of electrokinetic effects, such as dielectrophoresis, induced charge electrophoresis, and diode propulsion, can selectively power the microparticle motions and interactions. The ability to achieve on-demand locomotion, tractable fluid flows, synchronized motility, and reversible assembly using engineered silicon microparticles may enable advanced applications that include remotely powered microsensors, artificial muscles, reconfigurable neural networks and computational systems.

PCNA Loading by RFC, Mechanism of

KAUST Repository

Oke, Muse

2018-01-29

Replicative polymerases achieve highly processive DNA synthesis by binding to a clamp-like processivity factor that is topologically linked to DNA. The eukaryotic processivity clamp, proliferating cell nuclear antigen (PCNA), exists mostly as a closed ring in solution. Replication factor C (RFC), a five-subunit ATP-dependent protein complex, mediates PCNA opening in solution (assembly stage) and closing onto the primer-template (disassembly stage). In the assembly stage, RFC binding to ATP causes conformational changes that trigger RFC to form a complex with PCNA. PCNA is then cracked open at one subunit interface, and both RFC and PCNA adopt an extended spiral structure with a chamber that selects for a primer-template DNA structure. Binding of RFC/PCNA to DNA triggers the disassembly stage by stimulating ATP hydrolysis. Subsequent conformational changes in RFC and PCNA lead to the closing of PCNA onto the primer-template and the dissociation of RFC.

Experience with vacuum distillation cleaning of a full-size steam generator

Energy Technology Data Exchange (ETDEWEB)

Smit, C C

1975-07-01

In the 50 MW Sodium Component Test Facility at Hengelo tests are conducted on several types of full size prototype steam generators and an intermediate heat exchanger. The necessary post-test examination of these prototype components requires a complete removal of all sodium. Since in some cases the endurance test has to be continued after internal inspection, the cleaning-method should be such that no damage occurs to the component. After partial disassembly and internal inspection the component will be reassembled and must be acceptable for further use. The qualification tests of the Neratoom straight tube steam generator were concluded in June 1974. The evaporator module was decided to be partially disassembled in order to meet the requirement of a thorough examination before fabrication of the SNR-generators is started. In preparation for the most suitable cleaning procedure, several methods of sodium removal were considered.

Microsoft Kinect Sensor Evaluation

Science.gov (United States)

Billie, Glennoah

2011-01-01

My summer project evaluates the Kinect game sensor input/output and its suitability to perform as part of a human interface for a spacecraft application. The primary objective is to evaluate, understand, and communicate the Kinect system's ability to sense and track fine (human) position and motion. The project will analyze the performance characteristics and capabilities of this game system hardware and its applicability for gross and fine motion tracking. The software development kit for the Kinect was also investigated and some experimentation has begun to understand its development environment. To better understand the software development of the Kinect game sensor, research in hacking communities has brought a better understanding of the potential for a wide range of personal computer (PC) application development. The project also entails the disassembly of the Kinect game sensor. This analysis would involve disassembling a sensor, photographing it, and identifying components and describing its operation.

A Comprehensive Mathematical Programming Model for Minimizing Costs in A Multiple-Item Reverse Supply Chain with Sensitivity Analysis

Directory of Open Access Journals (Sweden)

Mahmoudi Hoda

2014-09-01

Full Text Available These instructions give you guidelines for preparing papers for IFAC conferences. A reverse supply chain is configured by a sequence of elements forming a continuous process to treat return-products until they are properly recovered or disposed. The activities in a reverse supply chain include collection, cleaning, disassembly, test and sorting, storage, transport, and recovery operations. This paper presents a mathematical programming model with the objective of minimizing the total costs of reverse supply chain including transportation, fixed opening, operation, maintenance and remanufacturing costs of centers. The proposed model considers the design of a multi-layer, multi-product reverse supply chain that consists of returning, disassembly, processing, recycling, remanufacturing, materials and distribution centers. This integer linear programming model is solved by using Lingo 9 software and the results are reported. Finally, a sensitivity analysis of the proposed model is also presented.

Effect of fluid-to-structure heat transfer on the structural damage potential to a liquid-metal fast breeder reactor

International Nuclear Information System (INIS)

Hakim, S.J.; Abramson, P.B.

1979-01-01

Deterministic calculations simulating a hypothetical accident in a liquid-metal fast breeder reactor that leads to a hydrodynamic disassembly of the core have been carried out to estimate the system's damage potential due to the vapor-pressure-driven expansion of molten core material and its dependency on the heat transfer to the remaining structure. These calculations ignored the effect on the work potential of sodium left in the core during the disassembly. Results indicate that steel cladding in the upper axial blankets and fission gas plenum acts as a thermodynamic energy sink that could reduce the total thermodynamic work energy by between one and two orders of magnitude, provided little or no sodium is present in the core at the time of interaction. These results have been found to be insensitive to the rate of heat transferred from the molten fuel to the molten steel that comprises the molten core material

Experience with vacuum distillation cleaning of a full-size steam generator

International Nuclear Information System (INIS)

Smit, C.C.

1975-01-01

In the 50 MW Sodium Component Test Facility at Hengelo tests are conducted on several types of full size prototype steam generators and an intermediate heat exchanger. The necessary post-test examination of these prototype components requires a complete removal of all sodium. Since in some cases the endurance test has to be continued after internal inspection, the cleaning-method should be such that no damage occurs to the component. After partial disassembly and internal inspection the component will be reassembled and must be acceptable for further use. The qualification tests of the Neratoom straight tube steam generator were concluded in June 1974. The evaporator module was decided to be partially disassembled in order to meet the requirement of a thorough examination before fabrication of the SNR-generators is started. In preparation for the most suitable cleaning procedure, several methods of sodium removal were considered

RTEL1 is a replisome-associated helicase that promotes telomere and genome-wide replication.

Science.gov (United States)

Vannier, Jean-Baptiste; Sandhu, Sumit; Petalcorin, Mark I R; Wu, Xiaoli; Nabi, Zinnatun; Ding, Hao; Boulton, Simon J

2013-10-11

Regulator of telomere length 1 (RTEL1) is an essential DNA helicase that disassembles telomere loops (T loops) and suppresses telomere fragility to maintain the integrity of chromosome ends. We established that RTEL1 also associates with the replisome through binding to proliferating cell nuclear antigen (PCNA). Mouse cells disrupted for the RTEL1-PCNA interaction (PIP mutant) exhibited accelerated senescence, replication fork instability, reduced replication fork extension rates, and increased origin usage. Although T-loop disassembly at telomeres was unaffected in the mutant cells, telomere replication was compromised, leading to fragile sites at telomeres. RTEL1-PIP mutant mice were viable, but loss of the RTEL1-PCNA interaction accelerated the onset of tumorigenesis in p53-deficient mice. We propose that RTEL1 plays a critical role in both telomere and genome-wide replication, which is crucial for genetic stability and tumor avoidance.

Inspection, maintenance, and repair of large pumps and piping systems using advanced robotic tools

International Nuclear Information System (INIS)

Lewis, R.K.; Radigan, T.M.

1998-01-01

Operating and maintaining large pumps and piping systems can be an expensive proposition. Proper inspections and monitoring can reduce costs. This was difficult in the past, since detailed pump inspections could only be performed by disassembly and many portions of piping systems are buried or covered with insulation. Once these components were disassembled, a majority of the cost was already incurred. At that point, expensive part replacement usually took place whether it was needed or not. With the completion of the Pipe Walkertrademark/LIP System and the planned development of the Submersible Walkertrademark, this situation is due to change. The specifications for these inspection and maintenance robots will ensure that. Their ability to traverse both horizontal and vertical, forward and backward, make them unique tools. They will open the door for some innovative approaches to inspection and maintenance of large pumps and piping systems

Transcriptome States Reflect Imaging of Aging States.

Science.gov (United States)

Eckley, D Mark; Coletta, Christopher E; Orlov, Nikita V; Wilson, Mark A; Iser, Wendy; Bastian, Paul; Lehrmann, Elin; Zhang, Yonqing; Becker, Kevin G; Goldberg, Ilya G

2018-06-14

In this study, we describe a morphological biomarker that detects multiple discrete subpopulations (or "age-states") at several chronological ages in a population of nematodes (Caenorhabditis elegans). We determined the frequencies of three healthy adult states and the timing of the transitions between them across the lifespan. We used short-lived and long-lived strains to confirm the general applicability of the state classifier and to monitor state progression. This exploration revealed healthy and unhealthy states, the former being favored in long-lived strains and the latter showing delayed onset. Short-lived strains rapidly transitioned through the putative healthy state. We previously found that age-matched animals in different age-states have distinct transcriptome profiles. We isolated animals at the beginning and end of each identified state and performed microarray analysis (principal component analysis, relative sample to sample distance measurements, and gene set enrichment analysis). In some comparisons, chronologically identical individuals were farther apart than morphologically identical individuals isolated on different days. The age-state biomarker allowed assessment of aging in a novel manner, complementary to chronological age progression. We found hsp70 and some small heat shock protein genes are expressed later in adulthood, consistent with the proteostasis collapse model.

Balancing of generators at wind power plants. Operational balancing in normal operation at wind power plants; Auswuchten von Generatoren auf Windkraftanlagen. Betriebsauswuchten im Normalbetrieb der Windkraftanlage

Energy Technology Data Exchange (ETDEWEB)

Franke, Dieter [IDF vibrodiagnose GmbH, Dresden (Germany); Schmidt, Gerrit [WSB Service GmbH (Germany)

2010-07-01

An increasing or suddenly arising unbalanced state in the generator of a wind power plant can be recognized by means of condition monitoring systems and regularly accomplished oscillation diagnoses. A strong unbalanced state results in a fast bearing wear, increases the risk of outage and reduces the profit. The risk of a further damage of the generator by means of a clearly increased vibration severity often is substantial. The counterbalancing takes place at the extended rotor at work benches in workshops. Among other things, the substantial cost is based on the expense of the disassembly and remounting of the generator. The total costs may amount several ten thousand Euro. As an alternative to balancing in the workshop, an operating balancing is recommended on the plant in order to reduce the costs. This was successfully realized by the engineer's office IDF vibrodiagnose GmbH (Dresden, Federal Republic of Germany) by the example of a Vestas V44 plant. The authors of the contribution under consideration describe the approach and advantages of an operating balancing. The main vibration stimulation at generators are described.

Activation of Basal Gluconeogenesis by Coactivator p300 Maintains Hepatic Glycogen Storage

Science.gov (United States)

Cao, Jia; Meng, Shumei; Ma, Anlin; Radovick, Sally; Wondisford, Fredric E.

2013-01-01

Because hepatic glycogenolysis maintains euglycemia during early fasting, proper hepatic glycogen synthesis in the fed/postprandial states is critical. It has been known for decades that gluconeogenesis is essential for hepatic glycogen synthesis; however, the molecular mechanism remains unknown. In this report, we show that depletion of hepatic p300 reduces glycogen synthesis, decreases hepatic glycogen storage, and leads to relative hypoglycemia. We previously reported that insulin suppressed gluconeogenesis by phosphorylating cAMP response element binding protein-binding protein (CBP) at S436 and disassembling the cAMP response element-binding protein-CBP complex. However, p300, which is closely related to CBP, lacks the corresponding S436 phosphorylation site found on CBP. In a phosphorylation-competent p300G422S knock-in mouse model, we found that mutant mice exhibited reduced hepatic glycogen content and produced significantly less glycogen in a tracer incorporation assay in the postprandial state. Our study demonstrates the important and unique role of p300 in glycogen synthesis through maintaining basal gluconeogenesis. PMID:23770612

Competing States in the t-J Model: Uniform d-Wave State versus Stripe State versus Stripe State

NARCIS (Netherlands)

Corboz, P.R.; Rice, T.M.; Troyer, M.

2014-01-01

Variational studies of the t-J model on the square lattice based on infinite projected-entangled pair states confirm an extremely close competition between a uniform d-wave superconducting state and different stripe states. The site-centered stripe with an in-phase d-wave order has an equal or only

The association between state attachment security and state Mindfulness.

Directory of Open Access Journals (Sweden)

Christopher A Pepping

Full Text Available Recent research suggests that attachment and mindfulness are related, though the nature of this association is unclear. Here we present two studies examining whether there is a causal relationship between state attachment and state mindfulness. Study 1 investigated the effects of experimentally increasing state mindfulness on state attachment security. State mindfulness was successfully enhanced, but this led to no change in state attachment security. Study 2 investigated the effects of experimentally enhancing state attachment security on state mindfulness. State attachment security was successfully enhanced, but this did not lead to any change in state mindfulness. These findings suggest that there is not a direct, immediate causal relationship between state attachment and state mindfulness as a result of brief experimental manipulations. Future research should examine these associations in longer term interventions.

Imaging and Quantitation of a Succession of Transient Intermediates Reveal the Reversible Self-Assembly Pathway of a Simple Icosahedral Virus Capsid.

Science.gov (United States)

Medrano, María; Fuertes, Miguel Ángel; Valbuena, Alejandro; Carrillo, Pablo J P; Rodríguez-Huete, Alicia; Mateu, Mauricio G

2016-11-30

Understanding the fundamental principles underlying supramolecular self-assembly may facilitate many developments, from novel antivirals to self-organized nanodevices. Icosahedral virus particles constitute paradigms to study self-assembly using a combination of theory and experiment. Unfortunately, assembly pathways of the structurally simplest virus capsids, those more accessible to detailed theoretical studies, have been difficult to study experimentally. We have enabled the in vitro self-assembly under close to physiological conditions of one of the simplest virus particles known, the minute virus of mice (MVM) capsid, and experimentally analyzed its pathways of assembly and disassembly. A combination of electron microscopy and high-resolution atomic force microscopy was used to structurally characterize and quantify a succession of transient assembly and disassembly intermediates. The results provided an experiment-based model for the reversible self-assembly pathway of a most simple (T = 1) icosahedral protein shell. During assembly, trimeric capsid building blocks are sequentially added to the growing capsid, with pentamers of building blocks and incomplete capsids missing one building block as conspicuous intermediates. This study provided experimental verification of many features of self-assembly of a simple T = 1 capsid predicted by molecular dynamics simulations. It also demonstrated atomic force microscopy imaging and automated analysis, in combination with electron microscopy, as a powerful single-particle approach to characterize at high resolution and quantify transient intermediates during supramolecular self-assembly/disassembly reactions. Finally, the efficient in vitro self-assembly achieved for the oncotropic, cell nucleus-targeted MVM capsid may facilitate its development as a drug-encapsidating nanoparticle for anticancer targeted drug delivery.

Caenorhabditis elegans polo-like kinase PLK-1 is required for merging parental genomes into a single nucleus.

Science.gov (United States)

Rahman, Mohammad M; Munzig, Mandy; Kaneshiro, Kiyomi; Lee, Brandon; Strome, Susan; Müller-Reichert, Thomas; Cohen-Fix, Orna

2015-12-15

Before the first zygotic division, the nuclear envelopes of the maternal and paternal pronuclei disassemble, allowing both sets of chromosomes to be incorporated into a single nucleus in daughter cells after mitosis. We found that in Caenorhabditis elegans, partial inactivation of the polo-like kinase PLK-1 causes the formation of two nuclei, containing either the maternal or paternal chromosomes, in each daughter cell. These two nuclei gave rise to paired nuclei in all subsequent cell divisions. The paired-nuclei phenotype was caused by a defect in forming a gap in the nuclear envelopes at the interface between the two pronuclei during the first mitotic division. This was accompanied by defects in chromosome congression and alignment of the maternal and paternal metaphase plates relative to each other. Perturbing chromosome congression by other means also resulted in failure to disassemble the nuclear envelope between the two pronuclei. Our data further show that PLK-1 is needed for nuclear envelope breakdown during early embryogenesis. We propose that during the first zygotic division, PLK-1-dependent chromosome congression and metaphase plate alignment are necessary for the disassembly of the nuclear envelope between the two pronuclei, ultimately allowing intermingling of the maternal and paternal chromosomes. © 2015 Rahman et al. This article is distributed by The American Society for Cell Biology under license from the author(s). Two months after publication it is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

Teleportations of Mixed States and Multipartite Quantum States

Institute of Scientific and Technical Information of China (English)

YU Chang-Shui; WANG Ya-Hong; SONG He-Shan

2007-01-01

In this paper, we propose a protocol to deterministically teleport an unknown mixed state of qubit by utilizing a maximally bipartite entangled state of qubits as quantum channel. Ifa non-maximally entangled bipartite pure state is employed as quantum channel, the unknown mixed quantum state of qubit can be teleported with 1 - √1 - C2 probability, where C is the concurrence of the quantum channel. The protocol can also be generalized to teleport a mixed state of qudit or a multipartite mixed state. More important purpose is that, on the basis of the protocol, the teleportation of an arbitrary multipartite (pure or mixed) quantum state can be decomposed into the teleportation of each subsystem by employing separate entangled states as quantum channels. In the case of deterministic teleportation,Bob only needs to perform unitary transformations on his single particles in order to recover the initial teleported multipartite quantum state.

Supersqueezed states from squeezed states

International Nuclear Information System (INIS)

Nieto, M.M.

1992-01-01

Using super-Baker-Campbell-Hausdorff relations on the elements of the supergroup OSP(2/2), we derive the supersqueeze operator and the supersqueezed states, which are the supersymmetric generalization of the squeezed states of the harmonic oscillator

Quantum States Transfer by Analogous Bell States

International Nuclear Information System (INIS)

Mei Di; Li Chong; Yang Guohui; Song Heshan

2008-01-01

Transmitting quantum states by channels of analogous Bell states is studied in this paper. We analyze the transmitting process, constructed the probabilitic unitary operator, and gain the largest successful transfer quantum state probability.

State-to-State Mode Specificity: Energy Sequestration and Flow Gated by Transition State.

Science.gov (United States)

Zhao, Bin; Sun, Zhigang; Guo, Hua

2015-12-23

Energy flow and sequestration at the state-to-state level are investigated for a prototypical four-atom reaction, H2 + OH → H + H2O, using a transition-state wave packet (TSWP) method. The product state distribution is found to depend strongly on the reactant vibrational excitation, indicating mode specificity at the state-to-state level. From a local-mode perspective, it is shown that the vibrational excitation of the H2O product derives from two different sources, one attributable to the energy flow along the reaction coordinate into the newly formed OH bond and the other due to the sequestration of the vibrational energy in the OH spectator moiety during the reaction. The analysis provided a unified interpretation of some seemingly contradicting experimental observations. It is further shown that the transfer of vibrational energy from the OH reactant to H2O product is gated by the transition state, accomplished coherently by multiple TSWPs with the corresponding OH vibrational excitation.

Elongation Factor Ts Directly Facilitates the Formation and Disassembly of the Escherichia coli Elongation Factor Tu·GTP·Aminoacyl-tRNA Ternary Complex*

Science.gov (United States)

Burnett, Benjamin J.; Altman, Roger B.; Ferrao, Ryan; Alejo, Jose L.; Kaur, Navdep; Kanji, Joshua; Blanchard, Scott C.

2013-01-01

Aminoacyl-tRNA enters the translating ribosome in a ternary complex with elongation factor Tu (EF-Tu) and GTP. Here, we describe bulk steady state and pre-steady state fluorescence methods that enabled us to quantitatively explore the kinetic features of Escherichia coli ternary complex formation and decay. The data obtained suggest that both processes are controlled by a nucleotide-dependent, rate-determining conformational change in EF-Tu. Unexpectedly, we found that this conformational change is accelerated by elongation factor Ts (EF-Ts), the guanosine nucleotide exchange factor for EF-Tu. Notably, EF-Ts attenuates the affinity of EF-Tu for GTP and destabilizes ternary complex in the presence of non-hydrolyzable GTP analogs. These results suggest that EF-Ts serves an unanticipated role in the cell of actively regulating the abundance and stability of ternary complex in a manner that contributes to rapid and faithful protein synthesis. PMID:23539628

Expansion dynamics

International Nuclear Information System (INIS)

Knoll, J.

1985-10-01

A quantum dynamical model is suggested which describes the expansion and disassembly phase of highly excited compounds formed in energetic heavy-ion collisions. First applications in two space and one time dimensional model world are discussed and qualitatively compared to standard freeze-out concepts. (orig.)

Technique for in-place welding of aluminum backed up by a combustible material

Science.gov (United States)

Spagnuolo, A. C.

1971-01-01

Welding external aluminum jacket, tightly wrapped around inner layer of wood composition fiberboard, in oxygen free environment prevents combustion and subsequent damage to underlying fiberboard. Technique also applies to metal cutting in similar assemblies without disassembly to remove combustible materials from welding heat proximity.

40 CFR 91.118 - Certification procedure-testing.

Science.gov (United States)

2010-07-01

... unscheduled engine, emission control system, or fuel system adjustment, repair, removal, disassembly, cleaning... or system malfunction, or the repair of such failure or malfunction, does not render the engine... engine family designation, the rationale supporting the FEL choice, the type of information used as a...

Size-controlled and redox-responsive supramolecular nanoparticles

NARCIS (Netherlands)

Weinhart-Mejia, R.; Kronig, G.A.; Huskens, Jurriaan

2015-01-01

Control over the assembly and disassembly of nanoparticles is pivotal for their use as drug delivery vehicles. Here, we aim to form supramolecular nanoparticles (SNPs) by combining advantages of the reversible assembly properties of SNPs using host–guest interactions and of a stimulus-responsive

1982 annual status report: reactor safety

International Nuclear Information System (INIS)

1982-01-01

This report presents the projects of the Reactor Safety Program at the JRC: 1) Reliability and risk evolution; 2) LWR loss of coolant accident studies; 3) Primary system integrity; 4) LMFBR core accident initiation and transition phase; and, 5) LMFBR accident post disassembly phase

49 CFR 572.111 - General description.

Science.gov (United States)

2010-10-01

... Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY... before being used in vehicle tests specified in Standard 201. (c) Disassembly, inspection and assembly... 1997. (d) Sign convention for signal outputs is given in the reference document SAE J1733 of 1994-12...

75 FR 41850 - Amended Notice of Intent to Modify the Scope of the Surplus Plutonium Disposition Supplemental...

Science.gov (United States)

2010-07-19

... and packaging capabilities, including direct metal oxidation, to fulfill plutonium storage..., disassemble nuclear weapons pits (a weapons component) and convert the plutonium metal to an oxide form for fabrication into mixed uranium-plutonium oxide (MOX) reactor fuel in the Mixed Oxide Fuel Fabrication Facility...

40 CFR 89.109 - Maintenance instructions and minimum allowable maintenance intervals.

Science.gov (United States)

2010-07-01

... exhaust manifold heat control valve, etc.) may be performed on durability vehicles at the least frequent... adjustment, repair, removal, disassembly, cleaning, or replacement on emission data vehicles shall be... equivalent equipment, instruments, or tools will be available to dealerships and other service outlets and...

Trifluoroethanol modulates α-synuclein amyloid-like aggregate formation, stability and dissolution

DEFF Research Database (Denmark)

Di Carlo, Maria Giovanna; Vetri, Valeria; Buscarino, Gianpiero

2016-01-01

The conversion of proteins into amyloid fibrils and other amyloid-like aggregates is closely connected to the onset of a series of age-related pathologies. Upon changes in environmental conditions, amyloid-like aggregates may also undergo disassembly into oligomeric aggregates, the latter being r...

Noisy teleportation of qubit states via the Greenberger–Horne–Zeilinger state or the W state

International Nuclear Information System (INIS)

Yan-Ling, Li; Mao-Fa, Fang; Xing, Xiao; Chao, Wu; Li-Zhen, Hou

2010-01-01

The effects of distributing entanglement through the amplitude damping channel or the phase damping channel on the teleportation of a single-qubit state via the Greenberger–Horne–Zeilinger state and the W state are discussed. It is found that the average fidelity of teleportation depends on the type and rate of the damping in the channel. For the one-qubit affected case, the Greenberger–Horne–Zeilinger state is as robust as the W state, i.e., the same quantum information is preserved through teleportation. For the two-qubit affected case, the W state is more robust when the entanglement is distributed via the amplitude damping channel; if the entanglement is distributed via the phase damping channel, the W state is more robust when the noisy parameter is small while the Greenberger–Horne–Zeilinger state becomes more robust when it is large. For the three-qubit affected case, the Greenberger–Horne–Zeilinger state is more robust than the W state. (general)

State nuclear initiatives in the United States

International Nuclear Information System (INIS)

Strauss, P.L.; Stoiber, C.R.

1977-01-01

The paper deals with State nuclear initiatives regarding the role of nuclear power in the energy future of the United States. The question of whether and under what circumstances nuclear facilities should be used to generate electricity was put to the popular vote in several States in 1976. Some general principles of Federal-State relations are discussed with specific reference to nuclear regulations. The initiative mechanism itself is described as well as its legal form and background. The parallel developments in the State and Federal legislative consideration of nuclear issues is reviewed and the suggested reasons for the defeat of the proposals in the seven States concerned are discussed. Finally, the author draws some conclusions on the effects of the 1976 initiatives on future decision-making in the US on energy policy in general and nuclear power in particular. (NEA) [fr

Targeted Delivery and Sustained Antitumor Activity of Triptolide through Glucose Conjugation.

Science.gov (United States)

He, Qing-Li; Minn, Il; Wang, Qiaoling; Xu, Peng; Head, Sarah A; Datan, Emmanuel; Yu, Biao; Pomper, Martin G; Liu, Jun O

2016-09-19

Triptolide, a key ingredient from the traditional Chinese medicinal plant thunder god vine, which has been used to treat inflammation and autoimmune diseases for centuries, has been shown to be an irreversible inhibitor of the XPB subunit of the transcription factor TFIIH and initiation of RNA polymerase II mediated transcription. The clinical development of triptolide over the past two decades has been limited by its toxicity and low water solubility. Herein, we report the development of a glucose conjugate of triptolide, named glutriptolide, which was intended to target tumor cells overexpressing glucose transporters selectively. Glutriptolide did not inhibit XPB activity in vitro but demonstrated significantly higher cytotoxicity against tumor cells over normal cells with greater water solubility than triptolide. Furthermore, it exhibited remarkable tumor control in vivo, which is likely due to sustained stepwise release of active triptolide within cancer cells. These findings indicate that glutriptolide may serve as a promising lead for developing a new mechanistic class of anticancer drugs. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Parameter and State Estimator for State Space Models

Directory of Open Access Journals (Sweden)

Ruifeng Ding

2014-01-01

Full Text Available This paper proposes a parameter and state estimator for canonical state space systems from measured input-output data. The key is to solve the system state from the state equation and to substitute it into the output equation, eliminating the state variables, and the resulting equation contains only the system inputs and outputs, and to derive a least squares parameter identification algorithm. Furthermore, the system states are computed from the estimated parameters and the input-output data. Convergence analysis using the martingale convergence theorem indicates that the parameter estimates converge to their true values. Finally, an illustrative example is provided to show that the proposed algorithm is effective.

Results of the examination of channel H12/1

International Nuclear Information System (INIS)

Bauer, E.

1983-01-01

Channel H12/1 is one part of the channel unit of the High-Flux Reactor that has been affected by corrosion attack. It was disassembled after the appearance of a heavy water leak and examined in a hot cell. Results of the examination are presented

Reference: 198 [Arabidopsis Phenome Database[Archive

Lifescience Database Archive (English)

Full Text Available etion of either RIC4 or RIC3 causes tip growth defects that are rescued by overproduction or depletion...C4. RIC4 promotes F-actin assembly, whereas RIC3 activates Ca(2+) signaling that leads to F-actin disassembly. Overproduction or depl

40 CFR 86.429-78 - Maintenance, unscheduled; test vehicles.

Science.gov (United States)

2010-07-01

..., repair, removal, disassembly, cleaning, or replacement on vehicles shall be performed only with the... malfunction, or the repair of such failure or malfunction, does not render the vehicle unrepresentative of... maintenance under paragraph (a)(1)(i) of this section. (b) Repairs to vehicle components of test vehicles...

77 FR 1920 - Second Amended Notice of Intent To Modify the Scope of the Surplus Plutonium Disposition...

Science.gov (United States)

2012-01-12

... essential elements required to provide a pit disassembly and/or conversion capability at one or more of the... as transuranic waste at WIPP, provided that the material would meet the WIPP waste acceptance... activities, including storage of DWPF canisters and transuranic waste pending disposal. Impacts of the...

Air & Space Power Journal. Volume 19, Number 1, Spring 2005

Science.gov (United States)

2005-03-01

and engineers constructed a life-size mock-up of wood and canvas in Florida that they could quickly disassemble before Soviet spy satellites made...including those that were simply government-neutral and thus tolerant of the insurgents); a smaller US fingerprint on Iraqi internal security; and greater

14 CFR 91.409 - Inspections.

Science.gov (United States)

2010-01-01

... instructions for their use; (3) Enough housing and equipment for necessary disassembly and proper inspection of... rotorcraft unless the replacement times for life-limited parts specified in the aircraft specifications, type... time in service, calendar times, or cycles of operation accumulated under the previous program must be...

77 FR 54908 - Extension of the Public Review and Comment Period and Announcement of an Additional Public...

Science.gov (United States)

2012-09-06

... plutonium from pits that were declared excess to national defense needs. It also updates previous DOE NEPA analyses on plutonium disposition to consider additional options for pit disassembly and conversion, which... ADDRESSES. In preparing the final SPD Supplemental EIS, DOE will consider all comments presented at the...

In vitro protease cleavage and computer simulations reveal the HIV-1 capsid maturation pathway

Science.gov (United States)

Ning, Jiying; Erdemci-Tandogan, Gonca; Yufenyuy, Ernest L.; Wagner, Jef; Himes, Benjamin A.; Zhao, Gongpu; Aiken, Christopher; Zandi, Roya; Zhang, Peijun

2016-12-01

HIV-1 virions assemble as immature particles containing Gag polyproteins that are processed by the viral protease into individual components, resulting in the formation of mature infectious particles. There are two competing models for the process of forming the mature HIV-1 core: the disassembly and de novo reassembly model and the non-diffusional displacive model. To study the maturation pathway, we simulate HIV-1 maturation in vitro by digesting immature particles and assembled virus-like particles with recombinant HIV-1 protease and monitor the process with biochemical assays and cryoEM structural analysis in parallel. Processing of Gag in vitro is accurate and efficient and results in both soluble capsid protein and conical or tubular capsid assemblies, seemingly converted from immature Gag particles. Computer simulations further reveal probable assembly pathways of HIV-1 capsid formation. Combining the experimental data and computer simulations, our results suggest a sequential combination of both displacive and disassembly/reassembly processes for HIV-1 maturation.

Fast Flux Test Facility interim examination and maintenance cell - past, present, and future

International Nuclear Information System (INIS)

Vincent, J.R.

1990-01-01

The Fast Flux Test Facility (FFTF) interim examination and maintenance (IEM) cell was designed to perform interim examination and/or disassembly of experimental core components for final analysis elsewhere, as well as maintenance of sodium-wetted or neutron-activated internal reactor parts and plant support hardware. The first 10 yr of operation were mainly devoted to the disassembly and examination of core component test assemblies. While some maintenance was performed on reactor support equipment, such as the closed-loop ex-vessel machine (CLEM) sodium-wetted grapple, 90% of IEM cell availability has been devoted to core component tests. Some test assemblies originally considered for processing in the IEM cell have not been irradiated; others, not originally planned, have been designed, irradiated, and processed. While no major reactor equipment has required remote repair or maintenance, the IEM cell has served as the remote repair facility for its own in-cell equipment, and several innovative remote repairs have been accomplished and are described

Assessment of modularity architecture for recovery process of electric vehicle in supporting sustainable design

Science.gov (United States)

Baroroh, D. K.; Alfiah, D.

2018-05-01

The electric vehicle is one of the innovations to reduce the pollution of the vehicle. Nevertheless, it still has a problem, especially for disposal stage. In supporting product design and development strategy, which is the idea of sustainable design or problem solving of disposal stage, assessment of modularity architecture from electric vehicle in recovery process needs to be done. This research used Design Structure Matrix (DSM) approach to deciding interaction of components and assessment of modularity architecture using the calculation of value from 3 variables, namely Module Independence (MI), Module Similarity (MS), and Modularity for End of Life Stage (MEOL). The result of this research shows that existing design of electric vehicles has the architectural design which has a high value of modularity for recovery process on disposal stage. Accordingly, so it can be reused and recycled in component level or module without disassembly process to support the product that is environmentally friendly (sustainable design) and able reduce disassembly cost.

Oak Ridge TNS/PEPR Program is considering modified physics and engineering criteria to ease remote maintenance problems

International Nuclear Information System (INIS)

Spampinato, P.T.; Shannon, T.E.

1978-01-01

Early work on TNS/PEPR at ORNL consisted of systems trade studies to establish a baseline design. Representative parameters are shown in Table 1. Development of these parameters into a mechanical design focussed on the complexity of the device disassembly. Three modifications to the physics and engineering criteria are being studied to ease these problems of remote disassembly: (1) Increase allowable field ripple from 1% to a maximum of 3%, thereby reducing the number of TF coils. The result is increased access between coils. (2) Provide sufficient clearance in the bore of the toroidal coils to raise and lower the EF coils during torus segment removal. This assumes a requirement for equilibrium field (EF) coils close to the plasma. (3) Investigate a secondary vacuum enclosure (e.g., vacuum building concept) to eliminate the need for welded torus joints and TF coil dewars. This paper discusses these modifications, as well as some overall cost implications relating to ripple

Profluorescent PPV-Based Micellar System as a Versatile Probe for Bioimaging and Drug Delivery.

Science.gov (United States)

Zaquen, Neomy; Lu, Hongxu; Chang, Teddy; Mamdooh, Russel; Lutsen, Laurence; Vanderzande, Dirk; Stenzel, Martina; Junkers, Thomas

2016-12-12

Although micelles are commonly used for drug delivery purposes, their long-term fate is often unknown due to photobleaching of the fluorescent labels or the use of toxic materials. Here, we present a metal-free, nontoxic, nonbleaching, fluorescent micelle that can address these shortcomings. A simple, yet versatile, profluorescent micellar system, built from amphiphilic poly(p-phenylenevinylene) (PPV) block copolymers, for use in drug delivery applications is introduced. Polymer micelles made from PPV show excellent stability for up to 1 year and are successfully loaded with anticancer drugs (curcumin or doxorubicin) without requiring introduction of physical or chemical cross-links. The micelles are taken up efficiently by the cells, which triggers disassembly, releasing the encapsulated material. Disassembly of the micelles and drug release is conveniently monitored as fluorescence of the single polymer chains appear, which enables not only to monitor the release of the payload, but in principle also the fate of the polymer over longer periods of time.

Coupling of replisome movement with nucleosome dynamics can contribute to the parent-daughter information transfer.

Science.gov (United States)

Bameta, Tripti; Das, Dibyendu; Padinhateeri, Ranjith

2018-06-01

Positioning of nucleosomes along the genomic DNA is crucial for many cellular processes that include gene regulation and higher order packaging of chromatin. The question of how nucleosome-positioning information from a parent chromatin gets transferred to the daughter chromatin is highly intriguing. Accounting for experimentally known coupling between replisome movement and nucleosome dynamics, we propose a model that can obtain de novo nucleosome assembly similar to what is observed in recent experiments. Simulating nucleosome dynamics during replication, we argue that short pausing of the replication fork, associated with nucleosome disassembly, can be a event crucial for communicating nucleosome positioning information from parent to daughter. We show that the interplay of timescales between nucleosome disassembly (τp) at the replication fork and nucleosome sliding behind the fork (τs) can give rise to a rich 'phase diagram' having different inherited patterns of nucleosome organization. Our model predicts that only when τp ≥ τs the daughter chromatin can inherit nucleosome positioning of the parent.

Maintenance concept of the gas turbine in a 1640 MW direct cycle HTR

International Nuclear Information System (INIS)

Schmied, H.; Karaus, H.; Schenker, E.

1981-01-01

The description which follows refers to a helium-cooled high-temperature reactor with a gas turbine and a thermal output of 1640 MW. The turbomachine which comes into contact with the cooling gas is contaminated with radioactivity during its operation. For the maintenance of the turbomachine, a major inspection is planned at six-year intervals. This overhaul involves disassembling and dismantling the turbomachine. Two minor inspections, at two-year intervals, are planned between the major inspections. The minor inspections involve inspection of the bearings, for which purpose the turbomachine does not have to be disassembled and dismantled. This paper presents in summarized form the sequence in which the maintenance work is to be carried out for both the major and minor inspections. The shutdown time and the collective dose were estimated to this end. Costs have not yet been determined. Details of the concept are given and significant results from the areas dealing with release, deposition and decontamination have been appropriately adapted

Cutting and machining energetic materials with a femtosecond laser

Energy Technology Data Exchange (ETDEWEB)

Roeske, Frank; Benterou, Jerry; Lee, Ronald; Roos, Edward [Energetic Materials Center, Lawrence Livermore National Laboratory, P. O. Box 808, Livermore, CA 94550 (United States)

2003-04-01

A femtosecond (fs) laser has been used as a tool for solving many problems involving access, machining, disassembly, inspection and avoidance of undesirable hazardous waste streams in systems containing energetic materials. Because of the unique properties of the interaction of ultrashort laser pulses with matter, the femtosecond laser can be used to safely cut these energetic materials in a precise manner without creating an unacceptable waste stream. Many types of secondary high explosives (HE) and propellants have been cut with the laser for a variety of applications ranging from disassembly of aging conventional weapons (demilitarization), inspection of energetic components of aging systems to creating unique shapes of HE for purposes of initiation and detonation physics studies. Hundreds of samples of energetic materials have been cut with the fs laser without ignition and, in most cases, without changing the surface morphology of the cut surfaces. The laser has also been useful in cutting nonenergetic components in close proximity to energetic materials. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Disposal machine using a hydraulic shovel loader for waste home electric appliances; Yuatsu shoberunado wo katsuyoshita haikaden shori kikai

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-25

This paper presents a disposal machine system developed by Hitachi Kenki Co. for waste home appliances. EX60 disposal machine and 2-axis shear shredder were developed as work machines for volume reduction and efficient disposal of waste home appliances. The shredder with rotary cutters is featured by superior crunch performance and efficient shredding of waste home appliances, and can crash not only waste home appliances but also various objects such as bulky waste, waste plastics and waste tire for passenger cars at crash torques from 7000 to 12000kgf{center_dot}m. The shredder is featured by superior mobility and easy operability by self-running and full-hydraulic driving, low- noise engine, and noise/vibration reduction by low-speed large torque hydraulic motor. EX60 disposal machine has clamp fixing waste home appliances, and a grapple for disassembling and classification, and can efficiently disassemble and classify 4 kinds of waste home appliances and other wastes only by itself. 12 figs., 3 tabs.

Identification of Neuregulin-2 as a novel stress granule component.

Science.gov (United States)

Kim, Jin Ah; Jayabalan, Aravinth Kumar; Kothandan, Vinoth Kumar; Mariappan, Ramesh; Kee, Younghoon; Ohn, Takbum

2016-08-01

Stress Granules (SGs) are microscopically visible, phase dense aggregates of translationally stalled messenger ribonucleoprotein (mRNP) complexes formed in response to distinct stress conditions. It is generally considered that SG formation is induced to protect cells from conditions of stress. The precise constituents of SGs and the mechanism through which SGs are dynamically regulated in response to stress are not completely understood. Hence, it is important to identify proteins which regulate SG assembly and disassembly. In the present study, we report Neuregulin-2 (NRG2) as a novel component of SGs; furthermore, depletion of NRG2 potently inhibits SG formation. We also demonstrate that NRG2 specifically localizes to SGs under various stress conditions. Knockdown of NRG2 has no effect on stress-induced polysome disassembly, suggesting that the component does not influence early step of SG formation. It was also observed that reduced expression of NRG2 led to marginal increase in cell survival under arsenite-induced stress. [BMB Reports 2016; 49(8): 449-454].

Stepwise Assembly and Characterization of DNA Linked Two-Color Quantum Dot Clusters.

Science.gov (United States)

Coopersmith, Kaitlin; Han, Hyunjoo; Maye, Mathew M

2015-07-14

The DNA-mediated self-assembly of multicolor quantum dot (QD) clusters via a stepwise approach is described. The CdSe/ZnS QDs were synthesized and functionalized with an amphiphilic copolymer, followed by ssDNA conjugation. At each functionalization step, the QDs were purified via gradient ultracentrifugation, which was found to remove excess polymer and QD aggregates, allowing for improved conjugation yields and assembly reactivity. The QDs were then assembled and disassembled in a stepwise manner at a ssDNA functionalized magnetic colloid, which provided a convenient way to remove unreacted QDs and ssDNA impurities. After assembly/disassembly, the clusters' optical characteristics were studied by fluorescence spectroscopy and the assembly morphology and stoichiometry was imaged via electron microscopy. The results indicate that a significant amount of QD-to-QD energy transfer occurred in the clusters, which was studied as a function of increasing acceptor-to-donor ratios, resulting in increased QD acceptor emission intensities compared to controls.

31 CFR 515.321 - United States; continental United States.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false United States; continental United... General Definitions § 515.321 United States; continental United States. The term United States means the United States and all areas under the jurisdiction or authority thereof, including the Trust Territory of...

31 CFR 500.321 - United States; continental United States.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false United States; continental United... General Definitions § 500.321 United States; continental United States. The term United States means the United States and all areas under the jurisdiction or authority thereof, including U.S. trust territories...

31 CFR 535.321 - United States; continental United States.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false United States; continental United... General Definitions § 535.321 United States; continental United States. The term United States means the United States and all areas under the jurisdiction or authority thereof including the Trust Territory of...

Effects of Plectin Depletion on Keratin Network Dynamics and Organization.

Directory of Open Access Journals (Sweden)

Marcin Moch

Full Text Available The keratin intermediate filament cytoskeleton protects epithelial cells against various types of stress and is involved in fundamental cellular processes such as signaling, differentiation and organelle trafficking. These functions rely on the cell type-specific arrangement and plasticity of the keratin system. It has been suggested that these properties are regulated by a complex cycle of assembly and disassembly. The exact mechanisms responsible for the underlying molecular processes, however, have not been clarified. Accumulating evidence implicates the cytolinker plectin in various aspects of the keratin cycle, i.e., by acting as a stabilizing anchor at hemidesmosomal adhesion sites and the nucleus, by affecting keratin bundling and branching and by linkage of keratins to actin filament and microtubule dynamics. In the present study we tested these hypotheses. To this end, plectin was downregulated by shRNA in vulvar carcinoma-derived A431 cells. As expected, integrin β4- and BPAG-1-positive hemidesmosomal structures were strongly reduced and cytosolic actin stress fibers were increased. In addition, integrins α3 and β1 were reduced. The experiments furthermore showed that loss of plectin led to a reduction in keratin filament branch length but did not alter overall mechanical properties as assessed by indentation analyses using atomic force microscopy and by displacement analyses of cytoplasmic superparamagnetic beads using magnetic tweezers. An increase in keratin movement was observed in plectin-depleted cells as was the case in control cells lacking hemidesmosome-like structures. Yet, keratin turnover was not significantly affected. We conclude that plectin alone is not needed for keratin assembly and disassembly and that other mechanisms exist to guarantee proper keratin cycling under steady state conditions in cultured single cells.

Rapanos v. United States & Carabell v. United States

Science.gov (United States)

Documents associated with guidance for implementing the definition of waters of the United States under the Clean Water Act following the Rapanos v. United States, and Carabell v. United States Supreme Court decision.

Quantum Teleportation of Tripartite Arbitrary State via W State

Institute of Scientific and Technical Information of China (English)

XUE Zheng-Yuan; YI You-Min; CAO Zhuo-Liang

2005-01-01

A scheme of teleportation of a tripartite state via W state is suggested. The W state serves as quantum channels. Standard Bell-state measurements and Von Neumann measurements are performed. After the sender operates the measurements and informs the receiver her results, he can reconstruct the original state by the corresponding unitary transformation. The probability of the successful teleportation is also obtained.

Learning in the "Platform Society": Disassembling an Educational Data Assemblage

Science.gov (United States)

Williamson, Ben

2017-01-01

Schools are increasingly involved in diverse forms of student data collection. This article provides a sociotechnical survey of a data assemblage used in education. ClassDojo is a commercial platform for tracking students' behaviour data in classrooms and a social media network for connecting teachers, students, and parents. The hybridization of…

Application of laser processing for disassembly of nuclear power plants

Science.gov (United States)

Baranov, Gennady A.; Zinchenko, A. V.; Arutyunyan, R. B.

1998-12-01

Provision of safety and drop of ecological risk at salvaging of nuclear submarines (NSM) of Russia Navy Forces represents one of the most actual problems of nowadays. It is necessary to remove from services of Russian Navy Forces 170 - 180 nuclear submarines by 2000. At salvaging of Russian Navy Forces NSM it should be necessary to cut out reactor compartments with more than 150 thousand tons of gross weight and to fragment terminal carcasses of submarines with gross weight of 2 million tons. Taking into account overall dimensions of salvaging objects and Euro-standard requirement on the sizes of carcass fragments, for salvaging of one NSM it is necessary to execute more than 10 km of cuts. Using of conventional methods of gas and plasma cutting of ship constructions and equipment polluted with radioactive oxides and bedding of insulation and paint and varnish materials causes contamination of working zones and environment by a mix of radioactive substances and highly toxic combustion products, nomenclature of which includes up to 50 names. Calculations carried out in the Institute of industrial and Marine Medicine have shown that salvage of just one NSM with using of gas and plasma cutting are accompanied by discharge into an environment of up to 11.5 kg of chromium oxides, up to 22.5 kg of manganese oxides, up to 97 kg of carbon oxides and up to 650 kg of nitrogen oxides. Fragmentation of such equipment by a method of directional explosion or hydraulic jet is problematic because of complexity of treated constructions and necessity to create special protective facilities, which will accumulate a bulk of radioactive and toxic discharges, as a consequence of the explosion and spreaded by shock waves and water deluges. In a number of new technological processes the cutting with using of high-power industrial lasers radiation stands out. As compared with other technological processes, laser cutting has many advantages determined by such unique properties of laser radiation as large power, capability to concentrate power on the small area (up to 108 W/cm2), good spatial and temporal controllability. The laser cutting advantages are the following: (1) high efficiency; (2) capability to cut various materials (metals, alloys, plastics, rubber, ceramics) and their compositions (fiber glass plastics, rubber-plastics, cermets) by one installation; (3) minimum pollution in gas and condensed phases; (4) high degree of technological process automation; (5) remote character of cutting and personnel absence in a processing zone.

Binary Disassembly Block Coverage by Symbolic Execution vs. Recursive Descent

Science.gov (United States)

2012-03-01

softmmu/qemu $S2E - hda debian_lenny_i386_standard.qcow2 -loadvm 1 86 B.7 launch-x86 Description: Written in shell scripting code, launches the S2E...Also loads the previous snapshot of this disk image if there is one. #!/bin/sh S2E=/home/s2e/s2e/build/qemu-release/i386-s2e-softmmu/qemu $S2E - hda

77 FR 12182 - Safety Standard for Portable Bed Rails: Final Rule

Science.gov (United States)

2012-02-29

... comply with the registration card requirements. 76 FR 68668. In the Federal Register of April 11, 2011... normal disassembly (see Fig. 1). [GRAPHIC] [TIFF OMITTED] TR29FE12.004 3.1.6 consumer adjustment, n... arms are rotated 180 degrees above the vertical axis (Fig. 9). [[Page 12189

AUTO

DEFF Research Database (Denmark)

Gammelgaard Nielsen, Anders; Aagaard, Tine; Diaz, pauline

2011-01-01

AUTO is the first assignment that the students of Architecture are introduced to at the Aarhus school of Architecture. The aim is to give students an understanding of design through a generic working method. This by disassembling a car engine and staging its components through a series of castings...

Adaptive neuro-fuzzy system for malware detection | Sodiya ...

African Journals Online (AJOL)

The implementation of ANFSMD was carried out using Java Programming Language, Interactive Disassembler and Matlab because of their supports for implementation of micro-programs. A total of 20,750 malware programs from VX Heaven public dataset and 15,000 clean files from Filehippo were used for the evaluation.

Theoretical interpretation of high-energy nuclear collisions

International Nuclear Information System (INIS)

Fai, G.

1990-08-01

In the following, I briefly summarize the research results and progress under this project in the time period January 1, 1988--July 31, 1990. Published and unpublished research in this time period focused on aspects of nuclear disassembly, nuclear dynamics, and subnucleonic degrees of freedom in model field theories