WorldWideScience

Sample records for tetragonal batio3 ceramics

  1. Quantitative evaluation of the piezoelectric response of unpoled ferroelectric ceramics from elastic and dielectric measurements: Tetragonal BaTiO3

    Science.gov (United States)

    Cordero, F.

    2018-03-01

    A method is proposed for evaluating the potential piezoelectric response, that a ferroelectric material would exhibit after full poling, from elastic and dielectric measurements of the unpoled ceramic material. The method is based on the observation that the softening in a ferroelectric phase with respect to the paraelectric phase is of piezoelectric origin, and is tested on BaTiO3. The angular averages of the piezoelectric softening in unpoled ceramics are calculated for ferroelectric phases of different symmetries. The expression of the orientational average with the piezoelectric and dielectric constants of single crystal tetragonal BaTiO3 from the literature reproduces well the softening of the Young's modulus of unpoled ceramic BaTiO3, after a correction for the porosity. The agreement is good in the temperature region sufficiently far from the Curie temperature and from the transition to the orthorhombic phase, where the effect of fluctuations should be negligible, but deviations are found outside this region, and possible reasons for this are discussed. This validates the determination of the piezoelectric response by means of purely elastic measurements on unpoled samples. The method is indirect and, for quantitative assessments, requires the knowledge of the dielectric tensor. On the other hand, it does not require poling of the sample, and therefore is insensitive to inaccuracies from incomplete poling, and can even be used with materials that cannot be poled, for example, due to excessive electrical conductivity. While the proposed example of the Young's modulus of a ceramic provides an orientational average of all the single crystal piezoelectric constants, a Resonant Ultrasound Spectroscopy measurement of a single unpoled ceramic sample through the ferroelectric transition can in principle measure all the piezoelectric constants, together with the elastic ones.

  2. Anelastic anomalies and negative Poisson's ratio in tetragonal BaTiO3 ceramics

    International Nuclear Information System (INIS)

    Dong Liang; Stone, Donald S.; Lakes, Roderic S.

    2010-01-01

    Anelastic anomalies (sharp variations in modulus and damping with temperature) were observed in tetragonal BaTiO 3 via broadband viscoelastic spectroscopy after aging at 50 deg. C for 15 h. The effect was most pronounced under electrical short circuit condition, at low frequency and under small excitation strain (10 -6 ). Softening in bulk modulus and negative Poisson's ratio were observed near 60 deg. C. Effects are attributed to an oxygen vacancy mechanism. A relaxational model cannot account for sharp response at smaller strains. Heterogeneity of negative stiffness is considered as a cause.

  3. Linear electro-optical properties of tetragonal BaTiO 3

    Indian Academy of Sciences (India)

    Linear optical susceptibility and clamped linear electro-optical tensor coefficients of tetragonal BaTiO3 are calculated using a formalism based on bond charge theory. Calculated values are in close agreement with experimental data. The covalent Ti–O bonds constituting distorted TiO6 octahedral groups are found to be ...

  4. Fabrication and electrical investigations of Pb-doped BaTiO_3 ceramics

    International Nuclear Information System (INIS)

    Sareecha, N.; Shah, W.A.; Maqsood, A.; Anis-ur-Rehman, M.; Latif Mirza, M.

    2017-01-01

    Electrical properties of Pb doped BaTiO_3; PBT are investigated in the wide range of temperatures (40–700 °C) at 1 kHz frequency. PBT ceramics were fabricated through solid state sintering method. Pre fired BaTiO_3 prepared with Ba/Ti molar ratio of 0.98 was doped with PbCO_3 (<1 mole %). XRD patterns indicated perovskite phase with tetragonal structures (P4mm). Morphological studies (SEM) revealed grain development with increasing lead contents. With lead doping and its variation, Curie temperature (T_C) was shifted from 120 to 200 °C with broad dielectric constant peaks and dielectric anomalies with relaxor behavior were observed. Resistivity decreased with increasing temperature, all specimens showed semiconductor behavior with negative temperature coefficient of resistivity (NTCR) characteristics. Mobility of electrons increased with thermal activation due to hopping of charge carriers from one site to another. Ohmic conductivities and associated activation energies were evaluated by impedance spectroscopy. Conductivity followed the Arrhenius law with E_a = 1.187–1.169 eV which can be attributed to the ionic conduction owning to doubly ionized oxygen vacancies. Well-defined hysteresis P-E loops measured at room temperature depicted ferroelectric properties of the materials. - Graphical abstract: Temperature dependence of dielectric constant (Ɛ′) and resistivity (ρ) for pure and Pb-doped BaTiO_3 ceramics at 1 k Hz frequency. - Highlights: • Pb-doped BaTiO_3ceramics were fabricated through solid state sintering. • Electrical properties were studied at the temperatures 40–700 °C at 1 kHz. • Specimens showed negative temperature coefficient of resistivity characteristics. • Conductivity followed the Arrhenius law with E_a = 1.187–1.169 eV. • Ionic conduction was supposed to be responsible for conduction process.

  5. Microstructural properties of BaTiO3 ceramics and thin films

    International Nuclear Information System (INIS)

    Fundora C, A.; Portelles, J.J.; Siqueiros, J.M.

    2000-01-01

    A microstructural study of BaTiO 3 ceramics obtained by the conventional ceramic method is presented. Targets were produced to grow BaTiO 3 thin films by pulsed laser deposition on Pt/Ti/Si (100) substrates. X-ray diffraction, Auger Electron Spectroscopy, X-ray Photon Spectroscopy and Scanning Electron Microscopy were used to study the properties of the BaTiO 3 ceramic samples and thin films, as deposited and after an annealing process. (Author)

  6. Oxygen 1s excitation and tetragonal distortion from core-hole effect in BaTiO3

    Science.gov (United States)

    Bugnet, Matthieu; Radtke, Guillaume; Botton, Gianluigi A.

    2013-11-01

    The accurate description of the O 1s excitation in BaTiO3 has been elusive so far. In this Rapid Communication, the electronic structure and the high-resolution electron energy-loss near-edge structures of the O K edge in tetragonal BaTiO3 are investigated using first-principles calculations. The results demonstrate a clear correlation between the broadening of the lower energy fine structure and the anisotropic effects induced by the core-hole potential, which are directly related to the structural distortion occurring in tetragonal BaTiO3. Moreover, we show that a significant improvement of the description of higher-lying structures can be obtained when correcting the energy position of the Ba 4f states. This demonstrates that the O 1s spectrum can be a very effective probe of the distortion and changes in the local electronic structure, and be used as a sensitive tool for studying new materials and ferroelectric transitions.

  7. Critical behavior of the spontaneous polarization and the dielectric susceptibility close to the cubic-tetragonal transition in BaTiO3

    Directory of Open Access Journals (Sweden)

    H. Yurtseven

    2015-09-01

    Full Text Available Using Landau mean field model, the spontaneous polarization and the dielectric susceptibility are analyzed as functions of temperature and pressure close to the cubic–tetragonal (ferroelectric–paraelectric transition in BaTiO3. From the analysis of the dielectric susceptibility and the spontaneous polarization, the critical exponents are deduced in the classical and quantum limits for BaTiO3. From the critical behavior of the dielectric susceptibility, the spontaneous polarization can be described for the ferroelectric–paraelectric (cubic to tetragonal transition between 4 and 8 GPa at constant temperatures of 0 to 200 K in BaTiO3 within the Landau mean field model given here.

  8. THE APPLICATION OF STEREOLOGY METHOD FOR ESTIMATING THE NUMBER OF 3D BaTiO3CERAMIC GRAINS CONTACT SURFACES

    Directory of Open Access Journals (Sweden)

    Vojislav V Mitić

    2011-05-01

    Full Text Available Methods of stereological study are of great importance for structural research of electronic ceramic materials including BaTiO3-ceramic materials. The broad application of ceramics, based on barium-titanate, in advanced electronics nowadays demands a constant research of its structure, that through the correlation structureproperties, a fundamental in the basic materials properties prognosis triad (technology-structure-properties, leads to further prognosis and properties design of these ceramics. Microstructure properties of BaTiO3- ceramic material, expressed in grains' boundary contact, are of basic importance for electric properties of this material, particularly the capacity. In this paper, a significant step towards establishing control under capacitive properties of BaTiO3-ceramics is being done by estimating the number of grains contact surfaces. Defining an efficient stereology method for estimating the number of BaTiO3-ceramic grains contact surfaces, we have started from a mathematical model of mutual grains distribution in the prescribed volume of BaTiO3-ceramic sample. Since the real microstructure morphology of BaTiO3-ceramics is in some way disordered, spherical shaped grains, using computer-modelling methods, are approximated by polyhedra with a great number of small convex polygons. By dividing the volume of BaTiO3-ceramic sample with the definite number of parallel planes, according to a given pace, into the intersection plane a certain number of grains contact surfaces are identified. According to quantitative estimation of 2D stereological parameters the modelled 3D internal microstructure is obtained. Experiments were made by using the scanning electronic microscopy (SEM method with the ceramic samples prepared under pressing pressures up to 150 MPa and sintering temperature up to 1370°C while the obtained microphotographs were used as a base of confirming the validity of presented stereology method. This paper, by applying

  9. Effects of vacancies on atom displacement threshold energy calculations through Molecular Dynamics Methods in BaTiO3

    Science.gov (United States)

    Gonzalez Lazo, Eduardo; Cruz Inclán, Carlos M.; Rodríguez Rodríguez, Arturo; Guzmán Martínez, Fernando; Abreu Alfonso, Yamiel; Piñera Hernández, Ibrahin; Leyva Fabelo, Antonio

    2017-09-01

    A primary approach for evaluating the influence of point defects like vacancies on atom displacement threshold energies values Td in BaTiO3 is attempted. For this purpose Molecular Dynamics Methods, MD, were applied based on previous Td calculations on an ideal tetragonal crystalline structure. It is an important issue in achieving more realistic simulations of radiation damage effects in BaTiO3 ceramic materials. It also involves irradiated samples under severe radiation damage effects due to high fluency expositions. In addition to the above mentioned atom displacement events supported by a single primary knock-on atom, PKA, a new mechanism was introduced. It corresponds to the simultaneous excitation of two close primary knock-on atoms in BaTiO3, which might take place under a high flux irradiation. Therefore, two different BaTiO3 Td MD calculation trials were accomplished. Firstly, single PKA excitations in a defective BaTiO3 tetragonal crystalline structure, consisting in a 2×2×2 BaTiO3 perovskite like super cell, were considered. It contains vacancies on Ba and O atomic positions under the requirements of electrical charge balance. Alternatively, double PKA excitations in a perfect BaTiO3 tetragonal unit cell were also simulated. On this basis, the corresponding primary knock-on atom (PKA) defect formation probability functions were calculated at principal crystal directions, and compared with the previous one we calculated and reported at an ideal BaTiO3 tetrahedral crystal structure. As a general result, a diminution of Td values arises in present calculations in comparison with those calculated for single PKA excitation in an ideal BaTiO3 crystal structure.

  10. Formation Mechanism and Dispersion of Pseudo-Tetragonal BaTiO3-PVP Nanoparticles from Different Titanium Precursors: TiCl4 and TiO2

    Directory of Open Access Journals (Sweden)

    Jinhui Li

    2017-12-01

    Full Text Available Nano-sized tetragonal BaTiO3 (BT particles that are well dispersed in solution are essential for the dielectric layer in multilayer ceramic capacitor technology. A hydrothermal process using TiCl4 and BaCl2, as source of Ti and Ba, respectively, or the precursor TiO2 as seed for the formation of BT, and poly(vinylpyrrolidone (PVP as a surfactant, was employed in this study to enhance both the dispersibility and tetragonality (c/a simultaneously in a single reaction process. The process parameters, i.e., the ratio of TiO2 substitution of TiCl4, the reaction time, and PVP content were systematically studied, and the growth mechanism and relation between the tetragonality and the particle size are discussed. Dynamic light scattering (DLS analysis was used to show that truncated pseudo-tetragonal BT-PVP particles with an average size of 100 nm, having a narrow size distribution and a coefficient of variation (CV as low as 20% and being mono-dispersed in water, were produced. The narrow particle size distribution is attributed to the ability of PVP to inhibit the growth of BT particles, and the high c/a of BT-PVP to heterogeneous particle growth using TiO2 seeds.

  11. Microstructure evolution and electrical characterization of Lanthanum doped Barium Titanate (BaTiO_3) ceramics

    International Nuclear Information System (INIS)

    Billah, Masum; Ahmed, A.; Rahman, Md. Miftaur; Mahbub, Rubbayat; Gafur, M. A.; Bashar, M. Shahriar

    2016-01-01

    In the current work, we investigated the structural and dielectric properties of Lanthanum oxide (La_2O_3) doped Barium Titanate (BaTiO_3) ceramics and established a correlation between them. Solid state sintering method was used to dope BaTiO_3 with 0.3, 0.5 and 0.7 mole% La_2O_3 under different sintering parameters. The raw materials used were La_2O_3 nano powder of ~80 nm grain size and 99.995% purity and BaTiO_3 nano powder of 100 nm grain size and 99.99% purity. Grain size distribution and morphology of fracture surface of sintered pellets were examined by Field Emission Scanning Electron Microscope and X-Ray Diffraction analysis was conducted to confirm the formation of desired crystal structure. The research result reveal that grain size and electrical properties of BaTiO_3 ceramic significantly enhanced for small amount of doping (up to 0.5 mole% La_2O_3) and then decreased with increasing doping concentration. Desired grain growth (0.80-1.3 µm) and high densification (<90% theoretical density) were found by proper combination of temperature, sintering parameters and doping concentration. We found the resultant stable value of dielectric constant was 10000-12000 at 100-300 Hz in the temperature range of 30°-50° C for 0.5 mole% La_2O_3 with corresponding shift of curie temperature around 30° C. So overall this research showed that proper La"3"+ concentration can control the grain size, increase density, lower curie temperature and hence significantly improve the electrical properties of BaTiO_3 ceramics.

  12. The effects of additive on microstructure and electrical properties of batio3 ceramics

    Directory of Open Access Journals (Sweden)

    Paunović Vesna V.

    2004-01-01

    Full Text Available In this paper comparative investigations of microstructure and dielectric properties of BaTiO3 ceramics doped with 1.0 wt% of Nb2O5, MnCO3 and CaZrO3 have been done. BaTiO3 samples were prepared using conventional method of solid state sintering at 13000C for two hours. Two distinguish micro structural regions can be observed in sample doped with Nb2O5. The first one, with a very small grained microstructure and the other one, with a rod like grains. In MnCO3 and CaZrO3 doped ceramics the uniform microstructure is formed with average grain size about 0.5- 2µm and 3-5µm respectively. The highest value of dielectric permittivity at room temperature and the greatest change of permittivity in function of temperature were observed in MnCO3/BaTiO3. In all investigated samples dielectric constant after initially large value at low frequency attains a constant value at f = 6kHz. A dissipation factor is independent of frequency greater than 10 kHz and, depending of systems, lies in the range from 0.035 to 0.25. At temperatures above Curie temperatures, the permittivity of all investigated samples follows a Curie- Weiss law. A slight shift of Curie temperature to the lower temperatures, in respect of Curie temperature for undoped BaTiO3, was observed in all investigated samples.

  13. Synthesis and electrical properties of BaBiO3 and high resistivity BaTiO3–BaBiO3 ceramics

    Directory of Open Access Journals (Sweden)

    Nitish Kumar

    2016-12-01

    Full Text Available Ceramics of the composition BaBiO3 (BB were sintered in oxygen to obtain a single phase with monoclinic I2/m symmetry as suggested by high-resolution X-ray diffraction. X-ray photoelectron spectroscopy confirmed the presence of bismuth in two valence states — 3+ and 5+. Optical spectroscopy showed presence of a direct bandgap at ∼ 2.2eV and a possible indirect bandgap at ∼ 0.9eV. This combined with determination of the activation energy for conduction of 0.25eV, as obtained from ac impedance spectroscopy, suggested that a polaron-mediated conduction mechanism was prevalent in BB. The BB ceramics were crushed, mixed with BaTiO3 (BT, and sintered to obtain BT–BB solid solutions. All the ceramics had tetragonal symmetry and exhibited a normal ferroelectric-like dielectric response. Using ac impedance and optical spectroscopy, it was shown that resistivity values of BT–BB were orders of magnitude higher than BT or BB alone, indicating a change in the fundamental defect equilibrium conditions. A shift in the site occupancy of Bi to the A-site is proposed to be the mechanism for the increased electrical resistivity.

  14. FABRICATION AND MECHANICAL PROPERTIES OF Na0.5Bi0.5TiO3–BaTiO3 LEAD-FREE PIEZOELECTRIC CERAMICS

    Directory of Open Access Journals (Sweden)

    PAN YUSONG

    2014-03-01

    Full Text Available Piezoelectric ceramics with 0.94Na0.5Bi0.5TO3–0.06BaTiO3 compositions were fabricated by solid state mixed oxide method and sintered at different temperatures varying from 1050°C to 1150°C to obtain dense ceramics. Phase analysis using X-ray diffraction showed tetragonal perovskite structure of Na0.5Bi0.5TO3 with no BaTiO3 peak detected. The SEM observation revealed that the crystal grain size of the piezoelectric ceramics is on the nano-size dimensions under all the sintering temperature. The study on the compressive mechanical characteristics showed that the compressive strength of the 0.94Na0.5Bi0.5TO3–0.06BaTiO3 piezoelectric ceramics increases with the rise of sintering temperature and sintering time. The change behavior of the compressive strength with the rise of cold pressure presents increasing firstly and then decreases.

  15. Influence of domain on grain size effects of the dielectric properties of BaTiO3 nanoceramics and nanoparticles

    International Nuclear Information System (INIS)

    Fang Chao; Chen Liangyan; Zhou Dongxiang

    2013-01-01

    The dielectric property of BaTiO 3 nanoparticles and nanoceramics has been studied on the basis of Ginsburg-Landau-Devonshire thermodynamic theory. In this paper, considering nanodomains, Landau coefficients have been written as a function of grain size, and the dielectric constant of the material has been calculated at a variety of temperatures and grain size. The results indicate that with decreasing grain size, the dielectric peak decreases. The two lower dielectric peaks of the orthorhombic-rhombohedral phase and tetragonal-orthorhombic phase move to higher temperature, while cubic-tetragonal phase dielectric peak moves to lower temperature. The dielectric constant of BaTiO 3 ceramics decreases with decreasing grain size. The dielectric constant peak at room temperature is at the grain size which is larger than the critical grain size 17-30 nm. The calculated result is consistent with the experimental data.

  16. Grain-size effects on thermal properties of BaTiO3 ceramics

    Indian Academy of Sciences (India)

    Administrator

    decreasing grain size. Furthermore, the Curie temperature shifts to lower temperature with decreasing grain size. Keywords. Nanocrystalline ceramics; thermal properties; size effect. 1. Introduction. BaTiO3 has been widely used in the electronic industry for its high dielectric constant and low losses above room temperature ...

  17. Crystal structure, dielectric, ferroelectric and energy storage properties of La-doped BaTiO3 semiconducting ceramics

    Directory of Open Access Journals (Sweden)

    Venkata Sreenivas Puli

    2015-09-01

    Full Text Available Polycrystalline La-doped BaTiO3 (Ba(1-xLax\tTiO3 [x=0,0.0005,0.001,0.003] ceramics (denoted as BTO,BLT1,BLT2,BLT3 were synthesized by conventional solid-state reaction method and characterized by X-ray diffraction (XRD, scanning electron microscopy (SEM, and Raman spectroscopy. XRD and Raman spectra revealed single-phase tetragonal perovskite crystalline structure. Well-saturated polarization–electric field (P–E hysteresis loops were observed with the measurement frequency of 50 Hz at room temperature and confirmed ferroelectric nature of these ceramics and a high recoverable electrical energy storage density of 0.350 J/cm3 with energy efficiency (n∼9%, which is useful in energy storage capacitor applications. Dielectric studies revealed anomalies around 415–420 K and near the Curie temperature. The latter is attributed to the ferroelectric to paraelectric phase transition. Better dielectric performances were obtained for La-doped samples sintered at 1350°C for 4 h. Grain growth is inhibited with lanthanum (La incorporation into the BTO lattice. Room temperature semiconducting behavior with positive temperature coefficient of resistivity (PTCR behavior at TC is attributed to electron compensation mechanism.

  18. Synthesis and electrical properties of BaBiO 3 and high resistivity BaTiO 3 –BaBiO 3 ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Nitish [Oregon State Univ., Corvallis, OR (United States); Univ. of New South Wales, Sydney, NSW (Australia); Golledge, Stephen L. [Univ. of Oregon, Eugene, OR (United States); Cann, David P. [Oregon State Univ., Corvallis, OR (United States)

    2016-12-01

    Ceramics of the composition BaBiO3 (BB) were sintered in oxygen to obtain a single phase with monoclinic II2/mm symmetry as suggested by high-resolution X-ray diffraction. X-ray photoelectron spectroscopy confirmed the presence of bismuth in two valence states - 3+ and 5+. Optical spectroscopy showed presence of a direct bandgap at ~ 2.2eV and a possible indirect bandgap at ~ 0.9eV. This combined with determination of the activation energy for conduction of 0.25eV, as obtained from ac impedance spectroscopy, suggested that a polaron-mediated conduction mechanism was prevalent in BB. The BB ceramics were crushed, mixed with BaTiO3 (BT), and sintered to obtain BT–BB solid solutions. All the ceramics had tetragonal symmetry and exhibited a normal ferroelectric-like dielectric response. Using ac impedance and optical spectroscopy, it was shown that resistivity values of BT–BB were orders of magnitude higher than BT or BB alone, indicating a change in the fundamental defect equilibrium conditions. A shift in the site occupancy of Bi to the A-site is proposed to be the mechanism for the increased electrical resistivity.

  19. Effects of ultrasonication and conventional mechanical homogenization processes on the structures and dielectric properties of BaTiO3 ceramics.

    Science.gov (United States)

    Akbas, Hatice Zehra; Aydin, Zeki; Yilmaz, Onur; Turgut, Selvin

    2017-01-01

    The effects of the homogenization process on the structures and dielectric properties of pure and Nb-doped BaTiO 3 ceramics have been investigated using an ultrasonic homogenization and conventional mechanical methods. The reagents were homogenized using an ultrasonic processor with high-intensity ultrasonic waves and using a compact mixer-shaker. The components and crystal types of the powders were determined by Fourier-transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) analyses. The complex permittivity (ε ' , ε″) and AC conductivity (σ') of the samples were analyzed in a wide frequency range of 20Hz to 2MHz at room temperature. The structures and dielectric properties of pure and Nb-doped BaTiO 3 ceramics strongly depend on the homogenization process in a solid-state reaction method. Using an ultrasonic processor with high-intensity ultrasonic waves based on acoustic cavitation phenomena can make a significant improvement in producing high-purity BaTiO 3 ceramics without carbonate impurities with a small dielectric loss. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Fractal corrections of BaTiO3-ceramic sintering parameters

    Directory of Open Access Journals (Sweden)

    Mitić V.V.

    2014-01-01

    Full Text Available Morphology of ceramics grains and pores as well as Brownian character of particle dynamics inside ceramics specimen contributes to better understanding of the sintering process. BaTiO3-ceramics, studied in this paper, has light fractal form and it is emanated in three aspects. First, the surface of grains, even in starting green body as well as distribution of grains shows fractal behavior. Second, existence of pores and their distribution follow the rules of fractal geometry. Third, movement of particles inside viscous flow underlies the rule of Brownian motion, which is essentially a fractal category. These three elements, each in its domain influence sintering dynamics, and can be described by dimensionless quantitative factors, αs αp and αm, being normalized to the interval [0,1]. Following sintering process, the associate formulae of Frenkel, Scherer and Mackenzie-Shuttleworth are shown from the angle of view of ceramics fractal dimension changing that approaches to 3. Also, it is shown that the energy balance is not violated after applying fractal correction to quasi equilibrium of the energy emanating from surface area reduction ES and energy adopted by viscous flow Ef .[Projekat Ministarstva nauke Republike Srbije, br. 172057: Directed synthesis, structure and properties of multifunctional materials

  1. Ho2O3 additive effects on BaTiO3 ceramics microstructure and dielectric properties

    Directory of Open Access Journals (Sweden)

    Paunović Vesna

    2012-01-01

    Full Text Available Doped BaTiO3-ceramics is very interesting for their application as PTCR resistors, multilayer ceramic capacitors, thermal sensors etc. Ho doped BaTiO3 ceramics, with different Ho2O3 content, ranging from 0.01 to 1.0 wt% Ho, were investigated regarding their microstructural and dielectric characteristics. The samples were prepared by the conventional solid state reaction and sintered at 1320° and 1380°C in an air atmosphere for 4 hours. The grain size and microstructure characteristics for various samples and their phase composition was carried out using a scanning electron microscope (SEM equipped with EDS system. SEM analysis of Ho/BaTiO3 doped ceramics showed that in samples doped with a rare-earth ions low level, the grain size ranged from 20-30μm, while with the higher dopant concentration the abnormal grain growth is inhibited and the grain size ranged between 2- 10μm. Dielectric measurements were carried out as a function of temperature up to 180°C. The low doped samples sintered at 1380°C, display the high value of dielectric permittivity at room temperature, 2400 for 0.01Ho/BaTiO3. A nearly flat permittivity-response was obtained in specimens with higher additive content. Using a Curie-Weiss low and modified Curie-Weiss low the Curie constant (C, Curie temperature (Tc and a critical exponent of nonlinearity (γ were calculated. The obtained value of γ pointed out that the specimens have almost sharp phase transition. [Projekat Ministarstva nauke Republike Srbije, br. 172057: Directed synthesis, structure and properties of multifunctional materials

  2. EFFECTS OF NEODYMIUM DOPING ON DIELECTRIC AND OPTICAL PROPERTIES OF Ba(1-xNdxTi1.005O3 CERAMICS

    Directory of Open Access Journals (Sweden)

    Zhang W.

    2013-06-01

    Full Text Available This paper investigated the optical properties and dielectric properties of neodymium doped BaTiO3 ceramics prepared by Ba(1-xNdxTi1.005O3 powders synthesized via a hydrothermal method. The effects of Nd3+ ions content on the structure, dielectric properties and optical properties of the ceramics were studied. The structural analysis performed on the X-ray diffractometer shows that the phase compositions of all ceramics are tetragonal phase structure. The red shift of the absorption edge indicates the presence of defect energy levels which was proved by the UV-Vis-NIR diffuse reflection spectra. Dielectric property measurements show that Nd-doped BaTiO3 ceramics possess improved dielectric properties at low Nd3+ contents (x = 0.001 and 0.002, as demonstrated by decreased dependence to frequency for both the dielectric constant and dielectric loss.

  3. Glass ceramic toughened with tetragonal zirconia

    Science.gov (United States)

    Keefer, Keith D.; Michalske, Terry A.

    1986-01-01

    A phase transformation-toughened glass ceramic and a process for making it are disclosed. A mixture of particulate network-forming oxide, network-modifying oxide, and zirconium oxide is heated to yield a homogeneous melt, and this melt is then heat-treated to precipitate an appreciable quantity of tetragonal zirconia, which is retained at ambient temperature to form a phase transformation-toughened glass ceramic. Nucleating agents and stabilizing agents may be added to the mixture to facilitate processing and improve the ceramic's properties. Preferably, the mixture is first melted at a temperature from 1200.degree. to 1700.degree. C. and is then heat-treated at a temperature within the range of 800.degree. to 1200.degree. C. in order to precipitate tetragonal ZrO.sub.2. The composition, as well as the length and temperature of the heat-treatment, must be carefully controlled to prevent solution of the precipitated tetragonal zirconia and subsequent conversion to the monoclinic phase.

  4. Simulation of iron impurity in BaTiO3 crystals

    International Nuclear Information System (INIS)

    Stashans, Arvids; Castillo, Darwin

    2009-01-01

    Iron-doped barium titanate (BaTiO 3 ) has been simulated taking into account cubic and tetragonal crystallographic lattices of the crystal. A quantum-chemical method based on the Hartree-Fock formalism has been used throughout the study. The calculated equilibrium structures of Fe-doped crystals reveal the defect-inward displacements of the Ti and O atoms whereas the shifts for the Ba atoms are encountered to be away with respect to the Fe impurity. According to the analysis of electron density population and electron band structure it is found that some unusual chemical bonding might take place between the Fe atom and its six adjacent O atoms. The role of Fe impurity in the ferroelectric polarization of the tetragonal BaTiO 3 crystal has been discussed too.

  5. Synthesis of BaTiO3 powder from barium titanyl oxalate (BTO ...

    Indian Academy of Sciences (India)

    Unknown

    the synthesis of BaTiO3 from the mixture of barium car- bonate and titanium dioxide employing microwave heat- ing. They observed that hypostoichiometric TiO2 (TiO2–x) reacted with BaCO3 in the presence of microwave field at temperature as low as 350°C to give the mixture of hexa- gonal and tetragonal forms of BaTiO3 ...

  6. Direct Observation of Surface Potential Distribution in Insulation Resistance Degraded Acceptor-Doped BaTiO3 Multilayered Ceramic Capacitors

    Science.gov (United States)

    Hong, Kootak; Lee, Tae Hyung; Suh, Jun Min; Park, Jae-Sung; Kwon, Hyung-Soon; Choi, Jaeho; Jang, Ho Won

    2018-05-01

    Insulation resistance (IR) degradation in BaTiO3 is a key issue for developing miniaturized multilayer ceramic capacitors (MLCCs) with high capacity. Despite rapid progress in BaTiO3-based MLCCs, the mechanism of IR degradation is still controversial. In this study, we demonstrate the Al doping effect on IR degradation behavior of BaTiO3 MLCCs by electrical measurements and scanning Kelvin probe microscopy (SKPM). As the Al doping concentration in BaTiO3 increases, IR degradation of MLCCs seems to be suppressed from electrical characterization results. However, SKPM results reveal that the conductive regions near the cathode become lager with Al doping after IR degradation. The formation of conducting regions is attributed to the migration of oxygen vacancies, which is the origin of IR degradation in BaTiO3, in dielectric layers. These results imply that acceptor doping in BaTiO3 solely cannot suppress the IR degradation in MLCC even though less asymmetric IR characteristics and IR degradation in MLCCs with higher Al doping concentration are observed from electrical characterization. Our results strongly suggest that observing the surface potential distribution in IR degraded dielectric layers using SKPM is an effective method to unravel the mechanism of IR degradation in MLCCs.

  7. Microstructural and dielectrical characterization of Ho doped BaTiO3 ceramics

    Directory of Open Access Journals (Sweden)

    Marjanović Miloš

    2014-01-01

    Full Text Available The Ho doped BaTiO3 ceramics, with different Ho2O3 content, ranging from 0.01 to 1.0 wt % Ho, were investigated regarding their microstructural and dielectric characteristics. Doped BaTiO3 were prepared using conventional solid state reaction and sintered at 1380°C for four hours. SEM analysis of Ho/BaTiO3 doped ceramics showed that the low doped samples exhibit mainly fairly uniform and homogeneous microstructure with the grain size ranged from 20-40 μm. In the samples with the higher dopant concentration the abnormal grain growth is inhibited and the grain size ranged between 2-10 μm. Measurements of dielectric properties were carried out as a function of temperature up to 180 °C at different frequencies. The samples doped with 0.01wt % of Ho, exhibit the high value of dielectric permittivity (εr = 2160 at room temperature. A nearly flat permittivity-response was obtained in specimens with higher additive content. Using a Curie-Weiss law and modified Curie-Weiss law the Curie constant (C, Curie temperature (Tc and a critical exponent of nonlinearity (g were calculated. The Curie temperature of doped samples were ranged from 128 to 130°C. The Curie constant for all series of samples decrease with increase of dopant concentration and the lowest values were observed on samples doped with 0.01 wt % of holmium. [Projekat Ministarstva nauke Republike Srbije, br. OI 172057: Directed synthesis, structure and properties of multifunctional materials i br. TR 32026

  8. Structural and electrical properties of Barium Titanate (BaTiO3 and Neodymium doped BaTiO3 (Ba0.995Nd0.005TiO3

    Directory of Open Access Journals (Sweden)

    Tuan Sulong Tuan Amirah

    2017-01-01

    Full Text Available Barium titanate (BaTiO3 and Neodymium (Nd doped BaTiO3 with composition Ba0.995Nd0.005TiO3 were prepared using conventional solid state reaction method to study the dielectric properties of materials. Pure phase samples were found at final heating temperature of 1400°C for overnight. X-ray diffraction analysis reveals the changes in the lattice parameter and unit cell volume of the pure perovskite tetragonal structure with space group (P4mm. Electrical analysis is carried out to investigate the dielectric properties, conductivity behaviour and dielectric loss of BaTiO3 and Ba0.995Nd0.005TiO3. Ba0.995Nd0.005TiO3 have a broaden dielectric peaks with high permittivity of 8000 and reasonably low loss tan δ which is about 0.004 (1 kHz.

  9. Orthorhombic strontium titanate in BaTiO sub 3 -SrTiO sub 3 superlattices

    CERN Document Server

    Rios, S; Jiang, A Q; Scott, J F; Lü, H; Chen, Z

    2003-01-01

    It has been suggested by several authors that SrTiO sub 3 layers in SrTiO sub 3 -BaTiO sub 3 superlattices should be tetragonal and ferroelectric at ambient temperatures, like the BaTiO sub 3 layers, rather than cubic, as in bulk SrTiO sub 3 , and that free-energy minimization requires continuity of the polarization direction. A recent ab initio calculation constrained solutions to this structure. Surprisingly, our x-ray study shows that the SrTiO sub 3 layers are orthorhombic with 0.03% in-plane strain, with the BaTiO sub 3 c-axis matching the SrTiO sub 3 a- and b-axis better than the c-axis; strain energy overcomes the cost in electrostatic energy. (letter to the editor)

  10. Enhanced dielectric and ferroelectric characteristics in Ca-modified BaTiO3 ceramics

    Directory of Open Access Journals (Sweden)

    Xiao Na Zhu

    2013-08-01

    Full Text Available Synergic modification of BaTiO3 ceramics was investigated by Ca-substitution, and the superior dielectric and ferroelectric properties were determined together with the structure evolution. X-ray diffraction (XRD analysis demonstrated a large solubility limit above x = 0.25 in Ba1−xCaxTiO3 solid solution where the fine grain structure was observed with increasing x. Room temperature dielectric constant as high as 1655 was achieved in the present ceramics together with the significantly reduced dielectric loss of 0.013 (x = 0.20 at 100 kHz, where the Curie temperature kept almost a constant while other two transition temperatures decreased continuously with increasing x. More importantly, the remanent polarization Pr and dielectric strength Eb were significantly enhanced by Ca-substitution, and the best Pr (11.34 μC/cm2 and the highest dielectric strength Eb (75 kV/cm were acquired at x = 0.25. The present ceramics should be very desirable for the applications such as high density energy storage devices.

  11. Effect of BaTiO3 Nanopowder Concentration on Rheological Behaviour of Ceramic Inkjet Inks

    Science.gov (United States)

    Kyrpal, R.; Dulina, I.; Ragulya, A.

    2015-04-01

    The relationship between rheological properties of ceramic inkjet inks based on BaTiO3 nanopowder and solid phase concentration has been investigated. In the ink volume takes place the formation periodic colloidal structures (PCS). The determining factor of structure formation is powder-dispersant ratio. Structural constitution of in the system with the low pigment concentration represented as PCS2, that contains solid particles in deflocculated that stabilized by the presence of adsorption-solvate layers. Dilatant structure formation for such inks explained by constrained conditions of the interaction. Samples with high BaTiO3 concentration have been classified as PKS1. Dilatant properties of the PKS1 resulted in particles rearrangement under the influence of the flow. In the region of some values powder-dispersant ratio take place conversation PKS2 to PKS1 and ink structure transformation from monodisperse to aggregate state.

  12. Piezoelectric properties and temperature stability of Mn-doped Pb(Mg1/3Nb2/3)-PbZrO3-PbTiO3 textured ceramics

    OpenAIRE

    Yan, Yongke; Cho, Kyung-Hoon; Priya, Shashank

    2012-01-01

    In this letter, we report the electromechanical properties of textured 0.4Pb(Mg1/3Nb2/3) O-3-0.25PbZrO(3)-0.35PbTiO(3) (PMN-PZT) composition which has relatively high rhombohedral to tetragonal (R-T) transition temperature (TR-T of 160 degrees C) and Curie temperature (T-C of 234 degrees C) and explore the effect of Mn-doping on this composition. It was found that MnO2-doped textured PMN-PZT ceramics with 5 vol.% BaTiO3 template (T-5BT) exhibited inferior temperature stability. The coupling f...

  13. First-principles calculations on the four phases of BaTiO3.

    Science.gov (United States)

    Evarestov, Robert A; Bandura, Andrei V

    2012-04-30

    The calculations based on linear combination of atomic orbitals basis functions as implemented in CRYSTAL09 computer code have been performed for cubic, tetragonal, orthorhombic, and rhombohedral modifications of BaTiO(3) crystal. Structural and electronic properties as well as phonon frequencies were obtained using local density approximation, generalized gradient approximation, and hybrid exchange-correlation density functional theory (DFT) functionals for four stable phases of BaTiO(3). A comparison was made between the results of different DFT techniques. It is concluded that the hybrid PBE0 [J. P. Perdew, K. Burke, M. Ernzerhof, J. Chem. Phys. 1996, 105, 9982.] functional is able to predict correctly the structural stability and phonon properties both for cubic and ferroelectric phases of BaTiO(3). The comparative phonon symmetry analysis in BaTiO(3) four phases has been made basing on the site symmetry and irreducible representation indexes for the first time. Copyright © 2012 Wiley Periodicals, Inc.

  14. Caracterización eléctrica y microestructural de cerámicas densificadas de BaTiO3 obtenido por pechini

    Directory of Open Access Journals (Sweden)

    Rivera, E.

    2010-12-01

    Full Text Available The barium titanate BaTiO3 is a material of great technological interest due to their dielectric properties. The functionality of this mixed oxide is mainly determined by its structure. Different synthesis methods have been used to improve the electrical response of BaTiO3. In this work BaTiO3 powders were synthesized using the polymeric precursor method, Pechini, obtaining the compound at 650 ° C, with uniform nanometric particle size (~ 20nm. The nature of the synthesized powders was analyzed using X-ray diffraction (XRD and differential scanning calorimetry (DSC. The results indicate that the crystalline phase present in the sample treated at 650 ° C is cubic and at 1100 ° C is tetragonal, with a relation c/a ≈ 1.007. The samples sinterized at 1100 ° C showed a ferroelectric-paraelectric transition at a temperature of T . 123ºC. The ceramic powders of barium titanate tetragonal, pressed and densified, was electrical characterizing with curves current-voltage (I-V at different temperatures. Additionally, we measured the change in electrical resistance versus temperature (R-T and we tested the behavior thermistor (PTCR of the material for different pressures. Also the electric response of the material with the variation of the frequency, for different temperatures, was measured.El titanato de bario BaTiO3 es un compuesto de gran interés tecnológico debido a sus propiedades dieléctricas. La funcionalidad de este oxido mixto está determinada, principalmente, por su estructura. Diferentes métodos de síntesis se han utilizado para mejorar la respuesta eléctrica del BaTiO3. En el presente trabajo se sintetizaron polvos de BaTiO3 utilizando el método de precursor polimérico, Pechini, obteniéndose el compuesto a una temperatura de 650 °C, con un tamaño de partícula nanométrico (~20nm y uniforme. La naturaleza de los polvos sintetizados se analizo utilizando difracción de rayos X (DRX y calorimetría diferencial de barrido (DSC

  15. Growth of BaTiO3-PVDF composite thick films by using aerosol deposition

    Science.gov (United States)

    Cho, Sung Hwan; Yoon, Young Joon

    2016-01-01

    Barium titanate (BaTiO3)-polyvinylidene fluoride (PVDF) composite thick films were grown by using aerosol deposition at room temperature with BaTiO3 and PVDF powders. To produce a uniform composition in ceramic and polymer composite films, which show a substantial difference in specific gravity, we used PVDF-coated BaTiO3 powders as the starting materials. An examination of the microstructure confirmed that the BaTiO3 were well distributed in the PVDF matrix in the form of a 0 - 3 compound. The crystallite size in the BaTiO3-PVDF composite thick films was 5 ˜ 50 times higher than that in pure BaTiO3 thick films. PVDF plays a role in suppressing the fragmentation of BaTiO3 powder during the aerosol deposition process and in controlling the relative permittivity.

  16. Effect of lithium doping in BaTiO3 ceramics for vibration sensor application

    Science.gov (United States)

    Praveen, E.; Murugan, S.; Jayakumar, K.

    2018-04-01

    Phase pure undoped and Lithium doped BaTiO3 particles have been synthesized by high temperature solid-state reaction method. Substitution of Lithium at the Ba2+ site in BaTiO3 lattice has been investigated. The structural, vibrational, electrical and mechanical characterization have been carried out. The poled samples were used as a sensing element for the detection of mechanical oscillations and the presence of 80 Hz pulse in the output spectrum manifest the response of the sensor element to the applied mechanical stress. In comparison with pure BaTiO3 the sensitivity of Li doped BaTiO3 is 14 times greater than the pure BaTiO3. This confirms that Li doped BaTiO3 could be an efficient candidate for the functionalization of vibration sensors in space application.

  17. Infrared studies of the monoclinic-tetragonal phase transition in Pb(Zr,Ti)O3 ceramics

    International Nuclear Information System (INIS)

    Guarany, C A; Pelaio, L H Z; Araujo, E B; Yukimitu, K; Moraes, J C S; Eiras, J A

    2003-01-01

    Recently, the observation of a new monoclinic phase in the PbZr 1-x Ti x O 3 (PZT) system in the vicinity of the morphotropic phase boundary was reported. Investigations of this new phase were reported using different techniques such as high-resolution synchrotron x-ray powder diffraction and Raman spectroscopy. In this work, the monoclinic → tetragonal phase transition in PbZr 0.50 Ti 0.50 O 3 ceramics was studied using infrared spectroscopy between 1000 and 400 cm -1 . The four possible ν 1 -stretching modes (Ti-O and Zr-O stretch) in the BO 6 octahedron in the ABO 3 structure of PZT in this region were monitored as a function of temperature. The lower-frequency mode ν 1 -(Zr-O) remains practically unaltered, while both intermediate ν 1 -(Ti-O) modes decrease linearly as temperature increases from 89 to 263 K. In contrast, the higher-frequency ν 1 -(Ti-O) and ν 1 -(Zr-O) modes present anomalous behaviour around 178 K. The singularity observed at this mode was associated with the monoclinic → tetragonal phase transition in PbZr 0.50 Ti 0.50 O 3 ceramics

  18. Size Tunable Synthesis of Highly Crystalline BaTiO3 Nanoparticles using Salt-Assisted Spray Pyrolysis

    International Nuclear Information System (INIS)

    Itoh, Yoshifumi; Lenggoro, I. Wuled; Okuyama, Kikuo; Maedler, Lutz; Pratsinis, Sotiris E.

    2003-01-01

    Highly crystalline, dense BaTiO 3 nanoparticles in a size range from 30 to 360nm with a narrow size distribution (σ g = 1.2-1.4) were prepared at various synthesis temperatures using a salt-assisted spray pyrolysis (SASP) method without the need for post-annealing. The effect of synthesis temperature on particle size, crystallinity and surface morphology of the nanoparticles were characterized by X-ray diffraction and scanning/transmission electron microscopy. The nature of the crystalline structure was analyzed by Rietveld refinement and Raman spectroscopy. The particle size decreased with decreasing operation temperature. The crystal phase was transformed from tetragonal to cubic at a particles size of about 50nm at room temperature. SASP can be used to produce high weight fraction of tetragonal BaTiO 3 nanoparticles down to 64nm in a single step

  19. Gold nanoparticles decorated on BaTiO3 as photocatalyst: effect of SPR and ferroelectricity

    Science.gov (United States)

    Miao, Zhilei; Chen, Lei; Wang, Rui; Yuan, Rongchun; Zhou, Fang; Lv, Pengfei; Zhang, Xiuyun; Wang, Qiang

    2018-02-01

    BaTiO3(BTO) powders with cubic(C) and tetragonal(T) crystalline structures were prepared by sol-gel method followed by calcination at different temperatures, and they were decorated with gold nanoparticles(AuNPs) to form Au-T-BTO and Au-C-BTO respectively. All the samples (C-BTO, T-BTO, Au-C-BTO and Au-T-BTO) were used as photo-catalysts for the degradation of Rhodamine B (RhB). Au-T-BTO exhibits the highest photocatalytic activity due to thecombined effect of surface plasmon resonance (SPR) and the ferroelectricity of the tetragonalphase BTO. The light absorption peaks at 500 to 600 nm verify the presence of SPR effect from Au NPs. Based on density functional theory (DFC) within the generalized gradient approximation (GGA) approach, it was demonstrated that the tetragonal phase BaTiO3 shows a spontaneous polarization with the calculated value of 0.34 C m-2, which is absent in thecubic phase. The internal space charge layer in tetragonal phase BTO enhances the separation of photoexcited carriers due to the spontaneous ferroelectric polarization, which also benefits photocatalytic activities.

  20. Room Temperature Monoclinic Phase in BaTiO3 Single Crystals

    Science.gov (United States)

    Denev, Sava; Kumar, Amit; Barnes, Andrew; Vlahos, Eftihia; Shepard, Gabriella; Gopalan, Venkatraman

    2010-03-01

    BaTiO3 is a well studied ferroelectric material for the last half century. It is well known to show phase transitions to tetragonal, orthorhombic and rhombohedral phases upon cooling. Yet, some old and some recent studies have argued that all these phases co-exist with a second phase with monoclinic distortion. Using optical second harmonic generation (SHG) at room temperature we directly present evidence for such monoclininc phase co-existing with tetragonal phase at room temperature. We observe domains with the expected tetragonal symmetry exhibiting 90^o and 180^o domain walls. However, at points of higher stress at the tips of the interpenetrating tetragonal domains we observe a well pronounced metastable ``staircase pattern'' with a micron-scale fine structure. Polarization studies show that this phase can be explained only by monoclinic symmetry. This phase is very sensitive to external perturbations such as temperature and fields, hence stabilizing this phase at room temperature could lead to large properties' tunability.

  1. Phase stabilization in plasma sprayed BaTiO3

    Czech Academy of Sciences Publication Activity Database

    Ctibor, Pavel; Seiner, Hanuš; Sedláček, J.; Pala, Zdeněk; Vaněk, Přemysl

    2013-01-01

    Roč. 39, č. 5 (2013), s. 5039-5048 ISSN 0272-8842 R&D Projects: GA ČR(CZ) GA101/09/0702 Institutional support: RVO:61389021 ; RVO:61388998 ; RVO:68378271 Keywords : Spectroscopy * BaTiO3 * Plasma spraying * Spark plasma sintering Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass; BJ - Thermodynamics (UT-L); JH - Ceramics, Fire-Resistant Materials and Glass (FZU-D) Impact factor: 2.086, year: 2013 http://www.sciencedirect.com/science/article/pii/S0272884212013582

  2. Some Aspects of the Failure Mechanisms in BaTiO3-Based Multilayer Ceramic Capacitors

    Science.gov (United States)

    Liu, David Donhang; Sampson, Michael J.

    2012-01-01

    The objective of this presentation is to gain insight into possible failure mechanisms in BaTiO3-based ceramic capacitors that may be associated with the reliability degradation that accompanies a reduction in dielectric thickness, as reported by Intel Corporation in 2010. The volumetric efficiency (microF/cm3) of a multilayer ceramic capacitor (MLCC) has been shown to not increase limitlessly due to the grain size effect on the dielectric constant of ferroelectric ceramic BaTiO3 material. The reliability of an MLCC has been discussed with respect to its structure. The MLCCs with higher numbers of dielectric layers will pose more challenges for the reliability of dielectric material, which is the case for most base-metal-electrode (BME) capacitors. A number of MLCCs manufactured using both precious-metal-electrode (PME) and BME technology, with 25 V rating and various chip sizes and capacitances, were tested at accelerated stress levels. Most of these MLCCs had a failure behavior with two mixed failure modes: the well-known rapid dielectric wearout, and so-called 'early failures." The two failure modes can be distinguished when the testing data were presented and normalized at use-level using a 2-parameter Weibull plot. The early failures had a slope parameter of Beta >1, indicating that the early failures are not infant mortalities. Early failures are triggered due to external electrical overstress and become dominant as dielectric layer thickness decreases, accompanied by a dramatic reduction in reliability. This indicates that early failures are the main cause of the reliability degradation in MLCCs as dielectric layer thickness decreases. All of the early failures are characterized by an avalanche-like breakdown leakage current. The failures have been attributed to the extrinsic minor construction defects introduced during fabrication of the capacitors. A reliability model including dielectric thickness and extrinsic defect feature size is proposed in this

  3. Structural evolution of Ba8Ti3Nb4O24 from BaTiO3 using a series of Ba(Ti1−5xNb4x)O3 solid solutions

    International Nuclear Information System (INIS)

    Barrientos Hernández, F.R.; Lira Hernández, I.A.; Gómez Yáñez, C.; Arenas Flores, A.; Cabrera Sierra, R.; Pérez Labra, M.

    2014-01-01

    Highlights: • The evolution phase Ba 8 Ti 3 Nb 4 O 24 was obtained through the mechanism Ba(Ti 1-5x Nb 4x )O 3 . • Addition of niobium can accelerate grain growth of BaTiO 3 ceramics. • Ba 8 Ti 3 Nb 4 O 24 presents a dielectric loss of 0.0035 and permittivity value of 54.6. • Electrical measurements showed that Nb 5+ content drops Curie temperature. • Samples with x ⩾ 0.0625 shows an insulating behavior. -- Abstract: In this work, the structural evolution of hexagonal phase Ba 8 Ti 3 Nb 4 O 24 by adding Nb 2 O 5 to perovskite structure of BaTiO 3 was investigated. The compositions Ba(Ti 1-5x Nb 4x )O 3 ceramics, with 0.00025 ⩽ x ⩽ 0.125 were prepared by the conventional solid state route in air atmosphere, the powders precursors, BaTiO 3 , BaCO 3 and Nb 2 O 5 , were mixed in stoichiometric proportions and ground in a ball mill using alumina balls and acetone. The mixed powders were calcined at temperatures up to 1500 °C. The phase transformation of Ba 8 Ti 3 Nb 4 O 24 from BaTiO 3 was studied by DRX, Raman spectroscopy, SEM, electrical measurements (relative permittivity and P–E hysteresis loops); Rietveld’s refinement was used to structurally characterize the samples. For the devices obtained capacitance was measured at 1 kHz; with these values we calculated the relative permittivity. The samples show typical P–E hysteresis loops at room temperature accompanied by saturation polarization (Ps) and remnant polarization (Pr). The DRX and Rietveld’s refinement results show x ⩽ 0.01 has a ferroelectric behavior. When the doped level is increased x ⩾ 0.02, a peak displacement is observed, this is due to the phase transformation of tetragonal to cubic into the unit cell. Finally, with x = 0.125 the crystal structure transforms to the characteristic hexagonal phase Ba 8 Ti 3 Nb 4 O 24 which resonates at microwave frequencies

  4. Effect of calcination routes on phase formation of BaTiO3 and their electronic and magnetic properties

    Science.gov (United States)

    Majumder, Supriyo; Choudhary, R. J.; Tripathi, M.; Phase, D. M.

    2018-05-01

    We have investigated the phase formation and correlation between electronic and magnetic properties of oxygen deficient BaTiO3 ceramics, synthesized by solid state reaction method, following different calcination paths. The phase analysis divulge that a higher calcination temperature above 1000° C is favored for tetragonal phase formation than the cubic phase. The core level X-ray photo electron spectroscopy measurements confirm the presence of oxygen vacancies and oxygen vacancy mediated Ti3+ states. As the calcination temperature and calcination time increases these oxygen vacancies and hence Ti3+ concentrations reduce in the sample. The temperature dependent magnetization curves suggest unexpected magnetic ordering, which may be due to the presence of unpaired electron at the t2g state (d1) of nearest-neighbor Ti atoms. In magnetization vs magnetic field isotherms, the regular decrease of saturation moment value with increasing calcination temperature and calcination time, can be discussed considering the amount of oxygen deficiency induced Ti3+ concentrations, present in the sample.

  5. Synthesis, structural characterization and dielectric properties of Nb doped BaTiO3/SiO2 core–shell heterostructure

    International Nuclear Information System (INIS)

    Cernea, M.; Vasile, B.S.; Boni, A.; Iuga, A.

    2014-01-01

    Highlights: • Optimal parameters for preparation by sol–gel of core–shell (BT-Nb 0.005 )/SiO 2 are presented in this paper. • Single crystalline BT-Nb 0.005 /SiO 2 core–shell composite with ∼34 nm shell thick was prepared. • The core–shell ceramic exhibits good dielectric properties and ferroelectric characteristics. -- Abstract: Perovskite complex ceramic oxides, BaTiO 3 doped with 0.5 mol%Nb 2 O 5 and then nanocoated with SiO 2 (abbreviated as BT-Nb 0.005 /SiO 2 ) was successful prepared using conventional sol–gel processing. Phase composition, particle morphology, structure, and electric properties of BT-Nb 0.005 core and BT-Nb 0.005 /SiO 2 core–shell were examined and compared, using X-ray diffraction, transmission electron microscopy and, dielectric and ferroelectric measurements. Core–shell composite with well-defined perovskite tetragonal phase of BaTiO 3 was achieved. Furthermore, single crystalline BT-Nb 0.005 /SiO 2 core–nanoshell heterostructure with ∼34 nm shell thick was prepared, which is a novelty in ferroelectrics field. The ferroelectric quality of BT-Nb 0.005 has suffered an alteration when the (BT-Nb 0.005 )/SiO 2 core–shell heterostructure was realized. One-dimensional BT-Nb 0.005 /SiO 2 core–shell heterostructure exhibits an improvement of dielectric losses and a decrease of dielectric constant, compared to uncoated BT-Nb 0.005 . The (BT-Nb 0.005 )/SiO 2 core–shell material could be interesting for application in the composite capacitors

  6. Multiphase nanodomains in a strained BaTiO3 film on a GdScO3 substrate

    Science.gov (United States)

    Kobayashi, Shunsuke; Inoue, Kazutoshi; Kato, Takeharu; Ikuhara, Yuichi; Yamamoto, Takahisa

    2018-02-01

    Controlling the crystal structure of ferroelectric materials via epitaxial strain, which is a well-known technique in strain engineering, can lead to the formation of unique domain structures generating non-intrinsic phenomena such as electronic conductivity, photovoltages, and enhanced piezoelectric characteristics. Strained BaTiO3 films are promising ferroelectric materials as theoretical modeling predicts that different domain morphologies can introduce additional properties not observed in conventional BaTiO3 ceramics. To rationally design materials for practical application, a thorough understanding of the formation mechanisms and stabilities of different domain structures in strained BaTiO3 films is required. However, there have been very few experimental reports on this topic, and details about the domain structures in strained BaTiO3 films are currently lacking. In this paper, we report multiphase nanodomains in a strained BaTiO3 film deposited on an orthorhombic GdScO3 substrate. The phase-transition behavior of the strained BaTiO3 film reveals that it contains multiple phases at room temperature; the film first undergoes a phase-transition upon heating at around 550 K, and then a paraelectric phase forms at temperatures above 690 K. A picometer-scale analysis of the Ti ion displacements, using an advanced scanning transmission electron microscopy technique, is used to characterize the complex multiphase nanodomains, providing useful insights into the control of domain structures in BaTiO3 films by applying epitaxial strain.

  7. Oxygen-vacancy defects on BaTiO3 (001) surface: a quantum chemical study

    International Nuclear Information System (INIS)

    Duque, Carlos; Stashans, Arvids

    2003-01-01

    A quantum-chemical study of technologically important BaTiO 3 crystal and oxygen-vacancy defects on its (001) surface is reported in the present work. The computations are made using a quantum-chemical method developed for periodic systems (crystals), which is based on the Hartree-Fock theory. The atomic rearrangement due to the surface creation is obtained for a pure BaTiO 3 by means of the periodic large unit cell (LUC) model and using an automated geometry optimisation procedure. The same technique is employed to study the electronic and structural properties of the material due to the presence of an O vacancy and F centre (two electrons trapped in an oxygen vacancy). The computations are carried out for both cubic and tetragonal lattices

  8. Cubic to tetragonal phase transition of Tm3+ doped nanocrystals in oxyfluoride glass ceramics

    International Nuclear Information System (INIS)

    Li, Yiming; Fu, Yuting; Shi, Yahui; Zhang, Xiaoyu; Yu, Hua; Zhao, Lijuan

    2016-01-01

    Tm 3+ ions doped β-PbF 2 nanocrystals in oxyfluoride glass ceramics with different doping concentrations and thermal temperatures are prepared by a traditional melt-quenching and thermal treatment method to investigate the structure and the phase transition of Tm 3+ doped nanocrystals. The structures are characterized by X-ray diffraction Rietveld analysis and confirmed with numerical simulation. The phase transitions are proved further by the emission spectra. Both of the doping concentration and thermal temperature can induce an O h to D 4h site symmetry distortion and a cubic to tetragonal phase transition. The luminescence of Tm 3+ doped nanocrystals at 800 nm was modulated by the phase transition of the surrounding crystal field

  9. [In vitro evaluation of low-temperature aging effects of Y2O3 stabilized tetragonal zirconia polycrystals dental ceramics].

    Science.gov (United States)

    Yi, Yuan-fu; Liu, Hong-chen; Wang, Chen; Tian, Jie-mo; Wen, Ning

    2008-03-01

    To investigate the influence of in vitro low-temperature degradation (LTD) treatment on the structural stability of 5 kinds of Y2O3 stabilized tetragonal zirconia polycrystals (Y-TZP) dental ceramics. TZ-3YS powder was compacted at 200 MPa using cold isostatic pressure and pre-sintered at 1050 degrees C for 2 h forming presintered blocks. Specimens were sectioned into 15 mm x 15 mm x 1.5 mm slices from blocks of TZ-3YS, Vita In-Ceram YZ, Ivoclar, Cercon Smart, and Kavo Y-TZP presintered blocks, 18 slices for each brand, and then densely sintered. Specimens were divided into 6 groups and subjected to an accelerated aging test carried out in an autoclave in steam at 134 degrees C, 0.2 MPa, for 0, 1, 2, 3, 4, and 5 h. X-ray diffraction (XRD) was used to identify crystal phases and relative content of monoclinic phase was calculated. Specimens for three-point bending test were fabricated using TZ-3YS ceramics according to the ISO 6872 standard and bending strength was tested before and after aging. The polished and aging specimens of TZ-3YS and Cercon Smart zirconia ceramics were observed by atomic force microscopy (AFM) to evaluate surface microstructure. Tetragonal-to-monoclinic phase transformation was detected for specimens of TZ-3YS, Vita In-Ceram YZ, Ivoclar, and Kavo zirconia ceramics except for Cercon Smart ceramics after aging, and the relative content of monoclinic phase was increasing with the prolonged aging time. TZ-3YS was the most affected material, Kavo took the second, and Vita and Ivoclar were similar. Aging had no significant negative effects on flexural strength of TZ-3YS with average bending strength being over 1100 MPa. The nucleation and growth of monoclinic phase were detected by AFM in surface of Cercon Smart zirconia in which monoclinic phase was not detected by XRD. The results suggest that LTD of dental Y-TZP is time dependent, but the aging test does not reduce the flexural strength of TZ-3YS. The long-term clinical serviceability of dental

  10. Microwave-Hydrothermal Synthesis and Characterization of High-Purity Nb Doped BaTiO3 Nanocrystals

    Directory of Open Access Journals (Sweden)

    A. Khanfekr

    2014-01-01

    Full Text Available The synthesis of Nb doped BaTiO3 has been investigated under Microwave-Hydrothermal (MH conditions in the temperature of 150°C for only 2 h using C16H36O4Ti, BaH2O2.8H2O and NbCl5 as Ba, Ti and  Nb sources, respectively.  Typical experiments performed on MH processing have not yet reported for Nb doped BaTiO3.  In the MH process, the formation of high purity nano tetragonal Nb-BaTiO3 was strongly enhanced. New hydrothermal method was used instead of the previous solid state reaction for the BaTiO3±Nb2O3 system. The new method uses high pressure to create nano dimension particles in a lower time and temperature. In case of the phase evolution studies, the XRD pattern measurements and Raman spectroscopy were performed. TEM and FE-SEM images were taken for the detailed analysis of the particle size, surface and morphology.  Synthesis of Nb doped BaTiO3 with the Microwave-hydrothermal provides an advantage of fast crystallization and reduced crystal size when compared to existing methods.

  11. Factors influencing formation of highly dispersed BaTiO3 nanospheres with uniform sizes in static hydrothermal synthesis

    International Nuclear Information System (INIS)

    Gao, Jiabing; Shi, Haiyue; Dong, Huina; Zhang, Rui; Chen, Deliang

    2015-01-01

    Highly dispersed BaTiO 3 nanospheres with uniform sizes have important applications in micro/nanoscale functional devices. To achieve well-dispersed spherical BaTiO 3 nanocrystals, we carried out as reported in this paper the systematic investigation on the factors that influence the formation of BaTiO 3 nanospheres by the static hydrothermal process, including the NaOH concentrations [NaOH], molar Ba/Ti ratios (R Ba/Ti ), hydrothermal temperatures, and durations, with an emphasis on understanding the related mechanisms. Barium nitrate and TiO 2 sols derived from tetrabutyl titanate were used as the starting materials. The as-synthesized BaTiO 3 samples were characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray analysis, thermogravimetry, differential thermal analysis, and FT-IR spectra. The highly dispersed BaTiO 3 nanospheres (76 ± 13 nm) were achieved under the optimum hydrothermal conditions at 200 °C for 10 h: [NaOH] = 2.0 mol L −1 and R Ba/Ti  = 1.5. Higher NaOH concentrations, higher Ba/Ti ratios, higher hydrothermal temperatures, and longer hydrothermal durations are favorable in forming BaTiO 3 nanospheres with larger fractions of tetragonal phase and higher yields; but too long hydrothermal durations resulted in abnormal growth and reduced the uniformity in particle sizes. The possible formation mechanisms for BaTiO 3 nanocrystals under the static hydrothermal conditions were investigated

  12. HRTEM analysis on nanocrystalline BaTiO3 and PbTiO3: size effects on ferroelectric phase transition temperature

    International Nuclear Information System (INIS)

    Bursill, L.A.; Jiang, B.; Peng, J.L.; Zhong, W.L.; Zhang, P.L.

    1997-01-01

    High-Resolution Transmission Electron Microscopic studies of nanocrystaline particles of BaTiO 3 and PbTiO 3 are reported. There are characteristic differences observed for BaTiO 3 prepared using sol gel (SG) and steric acid gel (SAG) methods. The former exhibit a critical size below which there is no paraelectric/ferroelectric phase transition, whereas BaTiO 3 prepared via the SAG route remained cubic for all conditions. The SAG preparations always showed chemical intergrowth defects whereas the SG preparations were single phase. Atomic resolution images of both varieties showed interesting surface steps and surface relaxations/reconstructions of some facets. Nanocrystalline PbTiO 3 prepared by the SG route remains tetragonal, albeit with decreasing c/a ratio, down to 25nm diameter. HRTEM observations of nanocrystalline PbTiO 3 are also presented. X-ray diffraction, dielectric and Raman scattering measurements also demonstrate pronounced size effects. The relationship between the observed nanostructures and size effects on the physical properties is discussed. 6 refs., 1 tab., 6 figs

  13. Thermal analysis of formation of nano-crystalline BaTiO3 using Ba(NO32 and TiO2

    Directory of Open Access Journals (Sweden)

    Md. Jawed Ansaree

    2015-12-01

    Full Text Available The reaction of Ba(NO32 with TiO2 was studied by thermogravimetric (TG and differential scanning calorimetric (DSC techniques up to 1000 °C and in nitrogen atmosphere. It was found that the formation of BaTiO3 takes place above 600 °C and that precursor mixing time and heating rate have no effect on the reaction temperature. BaTiO3 powder was prepared by calcination of Ba(NO32 and TiO2 precursor mixture at 800 °C for 8 h. X-ray diffraction analysis of the synthesized BaTiO3 confirmed the formation of tetragonal phase with lattice parameters a = 3.9950±0.0003 Å and c = 4.0318±0.0004 Å. Thermal analysis of the synthesized BaTiO3 powder showed weight loss within temperature range 40–1000 °C of only 0.40%. This small amount of weight loss was connected with some impurity phase, and identified as BaCO3 using Fourier transform infrared (FTIR technique.

  14. Hydrothermal growth of highly textured BaTiO3 films composed of nanowires

    International Nuclear Information System (INIS)

    Zhou Zhi; Tang Haixiong; Sodano, Henry A; Lin Yirong

    2013-01-01

    Textured barium titanate (BaTiO 3 ) films are attracting immense research interest due to their lead-free composition and excellent piezoelectric and dielectric properties. Most synthesis methods for these films require a high temperature, leading to the formation of a secondary phase and an overall decrease in the electrical properties of the ceramic. In order to alleviate these issues, a novel fabrication method is introduced by transferring oriented rutile TiO 2 nanowires to a textured BaTiO 3 film at temperatures below 160 °C. The microstructure and thickness of the fabricated BaTiO 3 films were characterized by scanning electron microscopy, and the crystal structure and degree of orientation were evaluated by x-ray diffraction patterns using the Lotgering method. It is shown that the thickness of the BaTiO 3 film can be controlled by the length of TiO 2 nanowire array template, and the degree of orientation of the textured BaTiO 3 films is highly dependent on the film thickness; the crystallographic orientation has been measured to reach up to 87%. The relative dielectric constant (ε r = 1300) and ferroelectric properties (P r = 2.7 μC cm −2 , E c = 4.0 kV mm −1 ) of the textured BaTiO 3 films were also characterized to demonstrate their potential application in sensors, random access memory, and micro-electromechanical systems. (paper)

  15. Positron annihilation lifetime study of positive temperature coefficient BaTiO3 samples

    International Nuclear Information System (INIS)

    Ling Chen; Mingkang Teng; Guanghou Wang; Xiaoyun Li; Tianchang Lu

    1989-01-01

    In order to investigate the doped vacancies in BaTiO 3 samples as well as their influence on the positive temperature coefficient (PTC) the positron annihilation lifetime spectroscopy was applied. Two groups of BaTiO 3 samples with BaO excess were prepared by doping different concentrations of La 2 O 3 and Nb 2 O 5 , respectively in the range from 0.1 to 3 at%. A third group of samples of two Sb-doped PTC BaTiO 3 semiconductors with excess BaO or TiO 2 were studied by the aid of positron technique before and after being reduced. It is shown that the positron lifetime parameters are sensitive to changes in the vacancy concentration in BaTiO 3 ceramics near the 0.1 mol% region. But they are almost unchanged during reduction processing; the resistivity of samples changed by one to two orders of magnitude through the reduction. It can be concluded that the PTC effect is due to oxygen on the grain boundary rather than vacancies, and that the Heywang-Jonker model is more reasonable

  16. Ceramic synthesis of 0.08BiGaO3-0.90BaTiO3-0.02LiNbO3 under high pressure and high temperature

    Science.gov (United States)

    Hui, Jin; Yong, Li; Mou-Sheng, Song; Lin, Chen; Xiao-Peng, Jia; Hong-An, Ma

    2016-07-01

    In this paper, the preparation of 0.08BiGaO3-0.90BaTiO3-0.02LiNbO3 is investigated at pressure 3.8 GPa and temperature 1100-1200 °C. Experimental results indicate that not only is the sintered rate more effective, but also the sintered temperature is lower under high pressure and high temperature than those of under normal pressure. It is thought that the adscititious pressure plays the key role in this process, which is discussed in detail. The composition and the structure of the as-prepared samples are recorded by XRD patterns. The result shows that the phases of BaTiO3, BaBiO2.77, and Ba2Bi4Ti5O18 with piezoelectric ceramic performance generate in the sintered samples. Furthermore, the surface morphology characteristics of the typical samples are also investigated using a scanning electron microscope. It indicates that the grain size and surface structure of the samples are closely related to the sintering temperature and sintering time. It is hoped that this study can provide a new train of thought for the preparation of lead-free piezoelectric ceramics with excellent performance. Project supported by the National Natural Science Foundation of China (Grant No. 51172089), the Natural Science Foundation of Education Department of Guizhou Province, China (Grant Nos. KY [2013]183 and LH [2015]7232), and the Research Fund for the Doctoral Program of Tongren University, China (Grant No. DS1302).

  17. Microstructure and dielectric parameters of epitaxial SrRuO3/BaTiO3/SrRuO3 heterostructures

    Science.gov (United States)

    Boikov, Yu. A.; Claeson, T.

    2001-05-01

    Epitaxial films of ferroelectric barium titanate are desirable in a number of applications but their properties are inferior to those of bulk material. Relations between microstructure and dielectric properties may give better understanding of limitations. Trilayer heterostructures SrRuO3/BaTiO3/SrRuO3 were grown by laser ablation on (100)LaAlO3 and (100)MgO substrates. The BaTiO3 layer was granular in structure. When grown on (100)SrRuO3/(100)LaAlO3, it was preferentially a-axis oriented due to tensile mechanical stress. Using (100)MgO as a substrate, on the other hand, produced a mixture of about equal value of a-axis and c-axis oriented grains of BaTiO3. The dielectric permittivity, ɛ, of the BaTiO3 layer was almost twice as large, at T>200 K and f=100 kHz, for the LaAlO3 substrate as compared to the MgO one. Its maximum value (ɛ/ɛ0≈6200) depended on temperature of growth, grain size, and electric field and compares well with optimal values commonly used for ceramic material. The maximum in the ɛ(T) shifted from about 370 to 320 K when the grain size in the BaTiO3 film decreased from 100 to 40 nm. At T300 K, hysteresis loops in polarization versus electric field were roughly symmetric. The BaTiO3 films grown on (100)SrRuO3/(100)MgO exhibit the largest remnant polarizations and coercive fields in the temperature range 100-380 K.

  18. The effect of secondary abnormal grain growth on the dielectric properties of La/Mn co-doped BaTiO3 ceramics

    Directory of Open Access Journals (Sweden)

    Živković Lj.M.

    2006-01-01

    Full Text Available La/Mn-codoped BaTiO3 systems, obtained by solid state reactions, were investigated regarding their microstructure characteristics and ferroelectric properties. Different concentrations of La2O3 were used for doping, ranging from 0.1 to 5.0 at% La, while a content of Mn was constant at 0.05 at%. For all samples sintered below the eutectic temperature (1332°C, a uniform microstructure was formed with average grain size from 1-3 μm. The appearance of secondary abnormal grains with (111 double twins grains with curved or faceted grain boundaries were observed in La/Mn BaTiO3 ceramics after sintering at temperatures above the eutectic temperature. All sintered samples exhibited a high electrical resistivity. Better dielectric performances were obtained for low doped samples (0.1 at% La sintered at 1350°C. For samples with La content above 1.0 at% a lower value in dielectric permittivity at higher sintering temperature is due to secondary abnormal grain growth, and to the presence of a non-ferroelectric phase rich in La. The Curie constant together with other dielectric parameters were also calculated.

  19. Piezoelectric properties and temperature stability of Mn-doped Pb(Mg1/3Nb2/3)-PbZrO3-PbTiO3 textured ceramics

    Science.gov (United States)

    Yan, Yongke; Cho, Kyung-Hoon; Priya, Shashank

    2012-03-01

    In this letter, we report the electromechanical properties of textured 0.4Pb(Mg1/3Nb2/3)O3-0.25PbZrO3-0.35PbTiO3 (PMN-PZT) composition which has relatively high rhombohedral to tetragonal (R-T) transition temperature (TR-T of 160 °C) and Curie temperature (TC of 234 °C) and explore the effect of Mn-doping on this composition. It was found that MnO2-doped textured PMN-PZT ceramics with 5 vol. % BaTiO3 template (T-5BT) exhibited inferior temperature stability. The coupling factor (k31) of T-5BT ceramic started to degrade from 75 °C while the random counterpart showed a very stable tendency up to 180 °C. This degradation was associated with the "interface region" formed in the vicinity of BT template. MnO2 doped PMN-PZT ceramics textured with 3 vol. % BT and subsequently poled at 140 °C (T-3BT140) exhibited very stable and high k31 (>0.53) in a wide temperature range from room temperature to 130 °C through reduction in the interface region volume. Further, the T-3BT140 ceramic exhibited excellent hard and soft combinatory piezoelectric properties of d33 = 720 pC/N, k31 = 0.53, Qm = 403, tan δ = 0.3% which are very promising for high power and magnetoelectric applications.

  20. Grain growth kinetics of textured-BaTiO3 ceramics

    Indian Academy of Sciences (India)

    Administrator

    3Department of Physics and Materials Science, City University of Hong Kong, Hong Kong ... Abstract. Textured BaTiO3 (BT) ceramics were fabricated by templated grain growth method. Effects of ... approaches to improve electrical properties of lead-free ceramics. ... modification methods to enhance the piezoelectric pro-.

  1. Effects of A-site nonstoichiometry on oxide ion conduction in 0.94Bi0.5Na0.5TiO3–0.06BaTiO3 ceramics

    Directory of Open Access Journals (Sweden)

    Sasiporn Prasertpalichat

    2016-06-01

    Full Text Available Lead free 0.94(Bi0.5Na0.5TiO3–0.06BaTiO3 ceramics were prepared by conventional solid-state mixed oxide route with the A-site stoichiometry modified to incorporate donor-doping (through Bi-excess and acceptor-doping (through Na-excess. Both stoichiometric and nonstoichiometric ceramics exhibited a single perovskite phase with pseudo-cubic symmetry. A significant improvement in the dielectric properties was observed in Bi-excess compositions and a deterioration in the dielectric properties was observed in Na-excess compositions. Impedance spectroscopy was utilized to analyze the effects of A-site nonstoichiometry on conduction mechanisms. Compositions with Bi-excess resulted in an electrically homogeneous microstructure with an increase in resistivity by ∼3–4 orders of magnitude and an associated activation energy of 1.57eV which was close to half of the optical bandgap. In contrast, an electrically heterogeneous microstructure was observed in both the stoichiometric and Na-excess compositions. In addition, the Na-excess compositions exhibited low resistivities (ρ∼103Ω-cm with characteristic peaks in the impedance data comparable to the recent observations of oxide ion conduction in (Bi0.5Na0.5TiO3. Long term annealing studies were also conducted at 800∘C to identify changes in crystal structure and electrical properties. The results of this study demonstrates that the dielectric and electrical properties of 0.94(Bi0.5Na0.5TiO3–0.06BaTiO3 ceramics are very sensitive to Bi/Na stoichiometry.

  2. Síntesis de polvos de BaTiO3 por mecanoquímica

    Directory of Open Access Journals (Sweden)

    Villaquirán Raigoza, C. F.

    2002-02-01

    Full Text Available The barium titanato, BaTiO3, is one of the electronic ceramics with more history of technological application in the industry of the ceramic capacitores. The actual technological demands, and the high quality required for the electronic devices, have driven to new alternatives of prosecution of these materials and to optimize the traditional techniques of raw materials synthesis it prevails. An alternative synthesis is to use the mechanical energy to modify the physiochemical properties of the dispersed system and to favor the obtaining of powders of BaTiO3. In this work the results are indicated obtained when using mechanical activation, physicochemistry, in the obtaining of the BaTiO3. It has been analyzed the effect of the time of mill and the nature of the precursor of the titanium on the transformation of phases in the samples during the thermal treatment to that are subjected. X-ray diffraction, DRX, was used to study the phases evolution and infrared spectroscopy, FTIR, to determine the functional groups present in the samples.El titanato de bario, BaTiO3, es uno de los cerámicos electrónicos con mayor historia de aplicación tecnológica en la industria de los capacitores cerámicos. Las demandas tecnológicas actuales, y la alta calidad requerida para los dispositivos electrónicos, han conducido a nuevas alternativas de procesamiento de estos materiales y a optimizar las técnicas tradicionales de síntesis de materia prima. Una alternativa de síntesis es utilizar la energía mecánica para modificar las propiedades fisicoquímicas del sistema disperso y favorecer la obtención de polvos de BaTiO3. En este trabajo se indican los resultados obtenidos al utilizar activación mecánica, mecanoquímica, en la obtención del BaTiO3. Se ha analizado el efecto del tiempo de molienda y la naturaleza del precursor del titanio sobre la transformación de fases que experimentan las muestras durante el tratamiento térmico a que son sometidas

  3. Dielectric properties of a BaTiO3 ceramic prepared by using the freeze drying method

    International Nuclear Information System (INIS)

    Al-Shakarchi, Emad K.

    2010-01-01

    A modified catecholate process has been developed to synthesize high-purity barium titanate by using a freeze drying method to produce ultra-fine powders from a barium titanium catechol complex, Ba[Ti(C 6 H 4 O 2 ) 3 ]. The complex prepared from TiCl 4 , C 6 H 4 (OH) 2 and BaCO 3 . The freeze drying of the complex Ba[Ti(C 6 H 4 O 2 ) 3 ] under a primary vacuum at a freezing temperature of -50 .deg. C for a long time 24 hrs is necessary to transfer the complex Ba[Ti(C 6 H 4 O 2 ) 3 ] from a liquid phase to a solid phase. A subsequent calcination of the complex for 12 hrs at a temperature of 700 .deg. C was very important to remove the acetates from the mixture. Finally, a sintering process was required for the pellets so that high density samples could be investigated. The dielectric properties, the structural phase, and the particle size of the sintered pellets have investigated as functions of frequency and temperature in order to determine the critical temperature for the phase transition. X-ray diffraction was used to investigate the structural properties and the particle size. The tetragonal phase of BaTiO 3 with the lattice constants a = b = 3.9734 A, and c = 4.012 A was successfully obtained.

  4. Ajuste teórico de las curvas PTCR de BaTiO3 dopado con niobio

    Directory of Open Access Journals (Sweden)

    Castro, M. S.

    2002-02-01

    Full Text Available In this work, a theoretical fitting to the experimental PTCR effect in slightly Nb-doped BaTiO3 from the Heywang-Jonker model is simulated. Besides, a qualitative approach was used to evaluate the GBBL characteristics of strongly Nb - doped BaTiO3. In both cases, a link between the electrical properties and the defect profile developed in these based - BaTiO3 ceramics was established. From the results, good agreement between experimental and calculated results was obtained for the PTCR ceramics. Asmall increment in Nb2O5 concentration leads to an increasing in the concentration of occupied acceptor states, the energy of the surface state and also the barrier height. In these cases, microstructural observations shown an important grain growth with average grain size between 10 and 100μm. EPR results clearly indicate low concentration of cationic vacancies for these materials. This phenomenon is associated to a charge-compensation mechanism in slightly-doped BaTiO3, that result in a semiconducting behaviour. On the other hand, the electrical behaviour of strongly–doped BaTiO3 moves away from the PTCR effect, and the material becomes insulating with noticeable GBBL characteristics. In this case, microstructural observations along defect structure analysis encourage the hypothesis in which barium vacancies act as acceptor at grain boundaries and play and important role in restricting grain growth of Nb2O5-BaTiO3 ceramics.En este trabajo se determinó la influencia de la concentración de Nb2O5 sobre el comportamiento PTCR de cerámicos basados en BaTiO3. Por otra parte, se estudió el impacto de una gran concentración del dopante sobre el comportamiento GBBL del BaTiO3. En ambos casos, se estableció una relación entre las propiedades eléctricas observadas y la estructura de defectos iónicos desarrollada. La aplicación del modelo de Heywang-Jonker permite el ajuste teórico de las curvas de resistividad – temperatura de los cerámicos PTCR

  5. CeO2-stabilized tetragonal ZrO2 polycrystals (Ce-TZP ceramics)

    International Nuclear Information System (INIS)

    Andrade Nono, M.C. de.

    1990-12-01

    This work presents the development and the characterization of CeO 2 -stabilized tetragonal ZrO 2 polycrystals (Ce-TZP ceramics), since it is considered candidate material for applications as structural high performance ceramics. Sintered ceramics were fabricated from mixtures of powders containing different CeO 2 content prepared by conventional and nonconventional techniques. These powders and their resultant sintered ceramics were specified by chemical and physical characterization, compactation state and mechanical properties. The chemical characteristics were determined by chemical analysis and the physical characteristics were evaluated by phase content, particle and agglomerate size and aspect, and powder porosity. (author)

  6. The effects of PbZn1/3Nb2/3O3-doping on structural, thermal, optical, dielectric, and ferroelectric properties of BaTiO3 ceramics

    Science.gov (United States)

    Suchanicz, J.; Świerczek, K.; Sitko, D.; Czaja, P.; Marchet, P.; Czternastek, H.; Majda, D.

    2017-09-01

    Low-lead (1-x)BT-xPZN (x = 0, 0.025, 0.05, 0.075, 0.10, 0.125, and 0.15) ceramics were successfully synthesized by the spark-plasma-sintering method for the first time. Their phase transition behavior as well as structural, thermal, optical, and electrical properties was investigated. These materials exhibit the structure of perovskite-type solid solutions and undergo a sequence of phase transitions, typical of pure BaTiO3 (BT). The dielectric test results revealed that with the increase in the PbZn1/3Nb2/3O3 (PZN) content, the frequency dispersion of electric permittivity increases, whilst the dielectric/ferroelectric properties tend to deteriorate, which is characteristic of relaxor-type behavior. Therefore, it is reasonable to suppose that these ceramics progressively lack long-range ordering. These effects are due to the competition between lone-pair electrons' induced changes in the A-O band upon Pb2+ addition and ionic size differences. In general, the transition temperatures observed by dielectric analyses are in good agreement with those obtained from X-ray diffraction and differential scanning calorimetry measurements. The BT-PZN system may help to understand why relaxor behavior appears in perovskite-based materials. It appears that these materials can become a good starting point for the development of new low-lead electronic ceramics.

  7. The influence of high hydrostatic pressure on lattice parameters of a single crystal of BaTiO3

    International Nuclear Information System (INIS)

    Malinowski, M.; Lukaszewicz, K.; Asbrink, S.

    1986-01-01

    The lattice parameters of a single crystal of BaTiO 3 have been measured under high hydrostatic pressure up to 5 GPa using a diamond-anvil high-pressure cell of a new design. The lattice becomes cubic at 2.08(8) GPa and stays cubic at higher pressures. The pressure dependence of the tetragonal-cubic transition temperature is estimated to be -46 K GPa -1 . (orig.)

  8. Electromechanical behavior of [001]-textured Pb(Mg1/3Nb2/3)O3-PbTiO3 ceramics

    Science.gov (United States)

    Yan, Yongke; Wang, Yu. U.; Priya, Shashank

    2012-05-01

    [001]-textured Pb(Mg1/3Nb2/3)O3-PbTiO3 (PMN-PT) ceramics were synthesized by using templated grain growth method. Significantly high [001] texture degree corresponding to 0.98 Lotgering factor was achieved at 1 vol. % BaTiO3 template. Electromechanical properties for [001]-textured PMN-PT ceramics with 1 vol. % BaTiO3 were found to be d33 = 1000 pC/N, d31 = 371 pC/N, ɛr = 2591, and tanδ = ˜0.6%. Elastoelectric composite based modeling results showed that higher volume fraction of template reduces the overall dielectric constant and thus has adverse effect on the piezoelectric response. Clamping effect was modeled by deriving the changes in free energy as a function of applied electric field and microstructural boundary condition.

  9. Structure and properties of plasma sprayed BaTiO3 coatings after thermal posttreatment

    Czech Academy of Sciences Publication Activity Database

    Ctibor, Pavel; Sedláček, J.; Pala, Zdeněk

    2015-01-01

    Roč. 41, č. 6 (2015), s. 7453-7460 ISSN 0272-8842 Institutional support: RVO:61389021 Keywords : Electrical properties * BaTiO3 * Plasma spraying * Annealing * Microstructure Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass Impact factor: 2.758, year: 2015 http://dx.doi.org/10.1016/j.ceramint.2015.02.065

  10. Ferroelectric BaTiO3 thin films on Ti substrate fabricated using pulsed-laser deposition.

    Science.gov (United States)

    He, J; Jiang, J C; Liu, J; Collins, G; Chen, C L; Lin, B; Giurgiutiu, V; Guo, R Y; Bhalla, A; Meletis, E I

    2010-09-01

    We report on the fabrication of ferroelectric BaTiO3 thin films on titanium substrates using pulsed laser deposition and their microstructures and properties. Electron microscopy studies reveal that BaTiO3 films are composed of crystalline assemblage of nanopillars with average cross sections from 100 nm to 200 nm. The BaTiO3 films have good interface structures and strong adhesion with respect to Ti substrates by forming a rutile TiO2 intermediate layer with a gradient microstructure. The room temperature ferroelectric polarization measurements show that the as-deposited BTO films possess nearly the same spontaneous polarization as the bulk BTO ceramics indicating formation of ferroelectric domains in the films. Successful fabrication of such ferroelectric films on Ti has significant importance for the development of new applications such as structural health monitoring spanning from aerospace to civil infrastructure. The work can be extended to integrate other ferroelectric oxide films with various promising properties to monitor the structural health of materials.

  11. Local geometric and electronic structures and origin of magnetism in Co-doped BaTiO3 multiferroics

    Science.gov (United States)

    Phan, The-Long; Thang, P. D.; Ho, T. A.; Manh, T. V.; Thanh, Tran Dang; Lam, V. D.; Dang, N. T.; Yu, S. C.

    2015-05-01

    We have prepared polycrystalline samples BaTi1-xCoxO3 (x = 0-0.1) by solid-state reaction. X-ray diffraction and Raman-scattering studies reveal the phase separation in crystal structure as changing Co-doping content (x). The samples with x = 0-0.01 are single phase in a tetragonal structure. At higher doping contents (x > 0.01), there is the formation and development of a secondary hexagonal phase. Magnetization measurements at room temperature indicate a coexistence of paramagnetic and weak-ferromagnetic behaviors in BaTi1-xCoxO3 samples with x > 0, while pure BaTiO3 is diamagnetic. Both these properties increase with increasing x. Analyses of X-ray absorption spectra recorded from BaTi1-xCoxO3 for the Co and Ti K-edges indicate the presence of Co2+ and Co3+ ions. They locate in the Ti4+ site of the tetragonal and hexagonal BaTiO3 structures. Particularly, there is a shift of oxidation state from Co2+ to Co3+ when Co-doping content increases. We believe that the paramagnetic nature in BaTi1-xCoxO3 samples is due to isolated Co2+ and Co3+ centers. The addition of Co3+ ions enhances the paramagnetic behavior. Meanwhile, the origin of ferromagnetism is due to lattice defects, which is less influenced by the changes caused by the variation in concentration of Co2+ and Co3+ ions.

  12. Size effect on the dielectric properties of BaTiO3 nanoceramics in a modified Ginsburg-Landau-Devonshire thermodynamic theory

    Science.gov (United States)

    Lin, Shan; Lü, Tianquan; Jin, Changqing; Wang, Xiaohui

    2006-10-01

    Grain size effects on the dielectric properties of BaTiO3 nanoceramics have been studied by using the modified Ginsburg-Landau-Devonshire (GLD) thermodynamic theory. Considering the existence of internal stresses, it is found that with decreasing grain size the transition temperature of cubic-tetragonal phase decreases, while those of tetragonal-orthorhombic and orthorhombic-rhombohedral phases increase. With further reducing grain size, our model predicts that the two ferroelectric structures of orthorhombic and tetragonal phases will become unstable and disappear at a critical size, leaving only one stable ferroelectric phase of rhombohedral structure. Consequently, a theoretical phase diagram of the transition temperature versus grain size is established wherein two triple points and a reentrance behavior are indicated. The results are compared with experimental data.

  13. Electric field-induced phase transitions and composition-driven nanodomains in rhombohedral-tetragonal potassium-sodium niobate-based ceramics

    KAUST Repository

    Lv, Xiang

    2017-08-07

    The mechanisms behind the high piezoelectricity of (K,Na)NbO3-based lead-free ceramics were investigated, including electric field-induced phase transitions and composition-driven nanodomains. The construction of a rhombohedral-tetragonal (R-T) phase boundary, confirmed using several advanced techniques, allowed a large piezoelectric constant (d33) of 450 ± 5 pC/N to be obtained in (1-x)K0.4Na0.6Nb0.945Sb0.055O3-xBi0.5Na0.5(Hf1-ySny)O3 (0 ≤ x ≤ 0.06 and 0 ≤ y ≤ 0.5) ceramics possessing an ultralow ΔUT-R of 7.4 meV. More importantly, the existence of an intermediate phase, i.e., the electric-induced phase (EIP), bridging the rhombohedral R [Ps//(111)] and tetragonal T [Ps//(001)] phases during the polarization rotation was demonstrated. Striped nanodomains (∼40 nm) that easily responded to external stimulation were also observed in the ceramics with an R-T phase. Thus, the enhanced piezoelectric properties originated from EIP and the striped nanodomains.

  14. Large recoverable electrostrain in Mn-doped (Ba,Sr) TiO3 ceramics

    International Nuclear Information System (INIS)

    Zhang, L.X.; Chen, W.; Ren, X.

    2004-01-01

    In this letter we demonstrate that with a different principle, BaTiO 3 ceramics, so far considered as inferior piezoelectrics compared with Pb(Zr,Ti)O 3 (PZT), can show a large recoverable electrostrain. This principle utilizes a point-defect-mediated reversible domain switching mechanism, which can in theory generate 0.368% strain for BaTiO 3 ceramics at the best condition. Experimental results showed that, after aging at room temperature, 1.0 mol % Mn-doped (Ba 0.95 Sr 0.05 )TiO 3 ceramics generate a large recoverable nonlinear strain of about 0.12%-0.15% at a field of 3 kV/mm. This value exceeds that of conventional hard PZT piezoelectric ceramics. A microscopic model for the domain-related electrostrain effect in ceramics is proposed. It is also found that the large electrostrain effect is quite stable with respect to both changing frequency and fatigue cycles. Large electrostrain remains recoverable down to 0.05 Hz and after 10 000 cycles. These results demonstrate the potential of our approach in achieving large recoverable electrostrain in environmental-friendly (Pb-free) ceramics

  15. Conformación de termistores utilizando polvos de BaTiO3 sintetizados por el método pechini

    Directory of Open Access Journals (Sweden)

    Claudia P. Fernández Perdomo

    2010-05-01

    Full Text Available El titanato de bario, BaTiO3, es un compuesto de gran interés en el ámbito de la electrocerámica, ya que se utiliza en la fabricación de condensadores, transductores piezoeléctricos y dispositivos resistivos con coeficiente positivo de temperatura (PTCR, así como en la manufactura de piroeléctricos y dispositivos optoelectrónicos, entre otros dispositivos. La mayoría de estos componentes son conformados con polvos cerámicos de elevada pureza y tamaño de partícula adecuado. Esto exige estructurar métodos de síntesis que garanticen es- tos requerimientos. En este trabajo se sintetizaron polvos cerámicos de BaTiO3 por el método de precursor polimérico (Pechini, obteniéndose una materia prima muy pura y con pequeño tamaño de partícula. Los polvos obtenidos se caracterizaron utilizando análisis térmico (ATD/TG, difracción de rayos X (DRX y calorimetría diferencial de barrido (DSC. Los resultados indican que en las muestras tratadas a 650 °C la única fase cristalina presente es el BaTiO3 cúbico y a 1.100 °C la tetragonal, con una relación c/a < 1.007. Las muestras tratadas a 1.100 °C presentaron una transición ferroeléctrica a paraeléctrica a una temperatura de T ≈ 123 °C. Los polvos cerámicos de BaTiO3 tetragonal fueron prensados uniaxialmente y posteriormente sinterizados a 1.200 °C durante 2 horas. Estas muestras se caracterizaron eléctricamente, obteniéndose curvas de resistencia eléctrica en función de la temperatura (R-T, evidenciándose en ellas su comportamiento termistor tipo PTCR. Además, se midió la variación de la corriente-voltaje (I-V a diferentes temperaturas.

  16. Low Friction in CuO-Doped Yttria-Stabilized Tetragonal Zirconia Ceramics: A Complementary Macro- and Nanotribology Study

    NARCIS (Netherlands)

    Tocha, E.; Pasaribu, H.R.; Schipper, Dirk J.; Schönherr, Holger; Vancso, Gyula J.

    2008-01-01

    The tribological behavior of CuO-doped yttria-stabilized tetragonal zirconia (3Y-TZP) ceramics in the absence of additional lubricants was characterized by macroscale pin-on-disk measurements and nanoscale atomic force microscopy (AFM) for a broad range of velocities. The previously observed low

  17. Structural, spectroscopic, and dielectric characterizations of Mn-doped 0.67BiFeO3-0.33BaTiO3 multiferroic ceramics

    KAUST Repository

    Hang, Qiming

    2013-09-07

    0.67BiFeO3-0.33BaTiO3 multiferroic ceramics doped with x mol% MnO2 (x = 2–10) were synthesized by solid-state reaction. The formation of a perovskite phase with rhombohedral symmetry was confirmed by X-ray diffraction (XRD). The average grain sizes were reduced from 0.80 μm to 0.50 μm as increasing the Mn-doped levels. Single crystalline nature of the grains was revealed by high-resolution transmission electron microscopy (HRTEM) images and electron diffraction patterns. Polar nano-sized ferroelectric domains with an average size of 9 nm randomly distributed in the ceramic samples were revealed by TEM images. Ferroelectric domain lamellae (71° ferroelectric domains) with an average width of 5 nm were also observed. Vibrational modes were examined by Raman spectra, where only four Raman peaks at 272 cm−1 (E-4 mode), 496 cm−1 (A 1-4 mode), 639 cm−1, and 1338 cm−1 were observed. The blue shifts in the E-4 and A 1-4 Raman mode frequencies were interpreted by a spring oscillator model. The dieletric constants of the present ceramics as a function of the Mn-doped levels exhibited a V-typed curve. They were in the range of 350–700 measured at 103 Hz, and the corresponding dielectric losses were in range of 0.43–0.96, approaching to 0.09 at 106 Hz.

  18. Structural, spectroscopic, and dielectric characterizations of Mn-doped 0.67BiFeO3-0.33BaTiO3 multiferroic ceramics

    KAUST Repository

    Hang, Qiming; Zhou, Wenke; Zhu, Xinhua; Zhu, Jianmin; Liu, Zhiguo; Al-Kassab, Talaat

    2013-01-01

    0.67BiFeO3-0.33BaTiO3 multiferroic ceramics doped with x mol% MnO2 (x = 2–10) were synthesized by solid-state reaction. The formation of a perovskite phase with rhombohedral symmetry was confirmed by X-ray diffraction (XRD). The average grain sizes were reduced from 0.80 μm to 0.50 μm as increasing the Mn-doped levels. Single crystalline nature of the grains was revealed by high-resolution transmission electron microscopy (HRTEM) images and electron diffraction patterns. Polar nano-sized ferroelectric domains with an average size of 9 nm randomly distributed in the ceramic samples were revealed by TEM images. Ferroelectric domain lamellae (71° ferroelectric domains) with an average width of 5 nm were also observed. Vibrational modes were examined by Raman spectra, where only four Raman peaks at 272 cm−1 (E-4 mode), 496 cm−1 (A 1-4 mode), 639 cm−1, and 1338 cm−1 were observed. The blue shifts in the E-4 and A 1-4 Raman mode frequencies were interpreted by a spring oscillator model. The dieletric constants of the present ceramics as a function of the Mn-doped levels exhibited a V-typed curve. They were in the range of 350–700 measured at 103 Hz, and the corresponding dielectric losses were in range of 0.43–0.96, approaching to 0.09 at 106 Hz.

  19. Type-I pseudo-first-order phase transition induced electrocaloric effect in lead-free Bi0.5Na0.5TiO3-0.06BaTiO3 ceramics

    Science.gov (United States)

    Li, Feng; Chen, Guorui; Liu, Xing; Zhai, Jiwei; Shen, Bo; Li, Shandong; Li, Peng; Yang, Ke; Zeng, Huarong; Yan, Haixue

    2017-05-01

    In this study, the electrocaloric effect (ECE) of Bi0.5Na0.5TiO3-0.06BaTiO3 (BNT-0.06BT) ceramic has been directly measured using a home-made adiabatic calorimeter. The maximum adiabatic temperature change (ΔT) approaches 0.86 K under an electric field of 5 kV/mm at 110 °C, which provides experimental evidence for optimizing the ECE near the type-I pseudo-first-order phase transition (PFOPT). Most importantly, a considerable ΔT value can be maintained over a wide temperature range well above the temperature of the PFOPT under a high electric field. In addition, ΔT is closely related to the structural transition and electric field strength. This work provides a guideline to investigate the high ECE in BNT-based ferroelectric ceramics for applications in cooling technologies.

  20. Substitution behavior of x(Na0.5K0.5)NbO3-(1 − x)BaTiO3 ceramics for multilayer ceramic capacitors by a near edge x-ray absorption fine structure analysis

    International Nuclear Information System (INIS)

    Ha, Jooyeon; Ryu, Jiseung; Lee, Heesoo

    2014-01-01

    The doping effect of (Na 0.5 K 0.5 )NbO 3 (NKN) as alternatives for rare-earth elements on the electrical properties of BaTiO 3 has been investigated, in terms of their substitution behavior. The dielectric constant of a specimen with x = 0.05 was about 79% higher than that of pure BaTiO 3 , and the temperature coefficient of capacitance was satisfied by the X7R specification. The specimen with x = 0.05 showed the lowest tetragonality among the four compositions and had a fine grain size of 5+ ion for Ti-sites. Therefore, the simultaneous substitution of Na + /K + and Nb 5+ ions into BaTiO 3 can improve dielectric properties, based on the charge-transfer process.

  1. Zn2+ in-situ substitution behavior during the formation of BaTiO3 coatings from plasma-sprayed powders collected in liquid nitrogen

    Science.gov (United States)

    Liu, Zhe; Xing, Zhiguo; Wang, Haidou; Xue, Zifan; Chen, Shuying; Cui, Xiufang; Jin, Guo

    2018-04-01

    The dielectric performance of BaTiO3 ceramic coatings is enhanced significantly by the addition of ZnO. In this study, the maximum relative permittivity value (εr ≈ 923) was measured in BaTiO3 coatings with ZnO added at 6 wt%. The Curie temperature (Tc) was in the range of 111 °C-121 °C for all of the ZnO-modified BaTiO3 coatings. Tc shifted to low temperatures as the ZnO content increased. Detailed analyses were performed to determine the phase composition and optical band gaps of powders collected in liquid nitrogen, which showed that the Zn2+ ions were incorporated into the BaTiO3 lattice where they substituted into the Ti4+ sites, and the composite powders (BaTiO3 + 6 wt% ZnO) tolerated high temperatures in the plasma beam. In addition, some residual Zn accumulated in the grain boundary in the form of ZnO. X-ray diffraction and Raman spectroscopy showed that the substitution led to changes in the compositional and structural properties. The red shift in the optical band gap of BaTiO3 indicated that the ZnTi'' defects caused by the dopants acted as carriers in the doped BaTiO3 coatings.

  2. Flux Growth of Highly Crystalline Photocatalytic BaTiO3 Particle Layers on Porous Titanium Sponge Substrate and Insights into the Formation Mechanism

    Science.gov (United States)

    Wang, Q.; Li, B.

    2017-09-01

    A unique architecture of idiomorphic and highly crystalline BaTiO3 particle layers directly grown on a porous titanium sponge substrate was successfully achieved for the first time using a facile molten salt method at a relatively low temperature of 700 °C. Specifically, the low-melting KCl-NaCl eutectic salts and barium hydroxide octahydrate were employed as the reaction medium and barium source, respectively. Powder X-ray diffraction (XRD), scanning electron microscopy (SEM), Energy dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and UV-vis diffuse reflectance spectrophotometry were used to characterize the structure, morphology and optical property of the obtained samples. The results revealed that the flux-grown tetragonal BaTiO3 products had well-defined and uniform morphology with an average size of 300 nm and a band gap of ∼3.16 eV. Based on XRD, EDS, SEM, and TEM, the possible formation mechanism responsible for the well-developed architecture of BaTiO3 particle layers was proposed and discussed. Furthermore, the photocatalytic activity of the flux-grown BaTiO3 products for organic pollutant degradation under simulated sunlight irradiation was also investigated.

  3. Understanding the peculiarities of the piezoelectric effect in macro-porous BaTiO3.

    Science.gov (United States)

    Roscow, James I; Topolov, Vitaly Yu; Bowen, Christopher R; Taylor, John; Panich, Anatoly E

    2016-01-01

    This work demonstrates the potential of porous BaTiO 3 for piezoelectric sensor and energy-harvesting applications by manufacture of materials, detailed characterisation and application of new models. Ferroelectric macro-porous BaTiO 3 ceramics for piezoelectric applications are manufactured for a range of relative densities, α  = 0.30-0.95, using the burned out polymer spheres method. The piezoelectric activity and relevant parameters for specific applications are interpreted by developing two models: a model of a 3-0 composite and a 'composite in composite' model. The appropriate ranges of relative density for the application of these models to accurately predict piezoelectric properties are examined. The two models are extended to take into account the effect of 90° domain-wall mobility within ceramic grains on the piezoelectric coefficients [Formula: see text]. It is shown that porous ferroelectrics provide a novel route to form materials with large piezoelectric anisotropy [Formula: see text] at 0.20 ≤ α ≤ 0.45 and achieve a high squared figure of merit [Formula: see text] [Formula: see text]. The modelling approach allows a detailed analysis of the relationships between the properties of the monolithic and porous materials for the design of porous structures with optimum properties.

  4. Far infrared and Raman response in tetragonal PZT ceramic films

    Energy Technology Data Exchange (ETDEWEB)

    Buixaderas, E.; Kadlec, C.; Vanek, P.; Drnovsek, S.; Ursic, H.; Malic, B.

    2015-07-01

    PbZr{sub 0}.38Ti{sub 0}.62O{sub 3} and PbZr{sub 0}.36Ti{sub 0}.64{sub O}3 thick films deposited by screen printing on (0 0 0 1) single crystal sapphire substrates and prepared at two different sintering temperatures, were studied by Fourier-transform infrared reflectivity, time-domain TH{sub z} transmission spectroscopy and micro-Raman spectroscopy. The dielectric response is discussed using the Lichtenecker model to account for the porosity of the films and to obtain the dense bulk dielectric functions. Results are compared with bulk tetragonal PZT 42/58 ceramics. The dynamic response in the films is dominated by an overdamped lead-based vibration in the TH{sub z} range, as known in PZT, but its evaluated dielectric contribution is affected by the porosity and roughness of the surface. (Author)

  5. Preparation, Structure, and Dielectric and Magnetic Properties of SrFe2/3W1/3O3 Ceramics

    Science.gov (United States)

    Pavlenko, A. V.; Turik, A. V.; Shilkina, L. A.; Kubrin, S. P.; Rusalev, Yu. V.; Reznichenko, L. A.; Andryushina, I. N.

    2018-03-01

    Polycrystalline samples of SrFe2/3W1/3O3 (SFWO) ceramic were obtained by solid-phase reactions with subsequent sintering using conventional ceramic technology. X-ray diffraction analysis showed that at room temperature, the SFWO ceramic is single-phase and has a perovskite-type structure with tetragonal symmetry and parameters a = 3.941(9) Å, c = 3.955(6) Å, and c/a = 1.0035. In studying the magnetic properties and the Mössbauer effect in SFWO ceramics, it is found that the material is a ferrimagnet, and the iron ions are only in the valence state of Fe3+. It is suggested that in the temperature range of T = 150-210°C, a smeared phase transition from a cubic (paraelectric) phase to a tetragonal (ferroelectric) phase takes place in SFWO with decreasing temperature.

  6. Synthesis and characterization of BaTiO3 ferroelectric material

    International Nuclear Information System (INIS)

    Osman, K.I.

    2011-01-01

    BaTiO 3 powder was prepared at low temperatures using the solid-state reaction, starting with two different precursors; the BaCO 3 /TiO 2 and the Ba(NO 3 ) 2 /TiO 2 powder mixtures. It was found that, a single phase BaTiO 3 was formed after calcination at 750 degree C for 10 h and at 600 degree C for 6 h for the first and second mixtures, respectively. Thermal and XRD analyses were used to study the formation kinetics of BaTiO 3 . Contracting volume reaction model was found to control both reactions. The SEM of the as milled powder, TMA, TG and thermodynamics analysis have been used to propose a realistic approach describing the reaction mechanism of BaTiO 3 . Characterization and the dielectric properties of the sintered BaTiO 3 were investigated. The relative permittivity and the dielectric loss measured at room temperature and at 1 khz were 2028.5 and 0.043 for BaTiO 3 prepared from BaCO 3 /TiO 2 , while they were 1805.33 and 0.41 for BaTiO 3 prepared from Ba(NO 3 ) 2 /TiO 2 .

  7. Wet routes of high purity BaTiO3 nanopowders

    International Nuclear Information System (INIS)

    Wang Liqiu; Liu Liang; Xue Dongfeng; Kang Hongmin; Liu Changhou

    2007-01-01

    High purity BaTiO 3 nanopowders were prepared in wet routes through stearic acid gel (SAG) and acetic acid gel (AAG) techniques, respectively. BaTiO 3 samples were characterized by X-ray diffraction, transmission electron microscope, Fourier transform infrared spectrometry, X-ray fluorescence spectrometry, and thermal gravimetric analysis. The present results indicate that both methods have a similar reaction process during calcination, while BaTiO 3 crystallites were initially formed at 550 deg. C by SAG and 800 deg. C by AAG. Both methods could produce BaTiO 3 powders with a cubic perovskite structure, while they had different grain size distributions within 25-50 nm for SAG and 50-80 nm for AAG. BaTiO 3 samples prepared by SAG had a lower agglomeration than those by AAG. SAG has shown many distinctive advantages in the preparation of high purity BaTiO 3 nanopowders, without Ba and Ti losses and hazardous wastes

  8. Microstructure, Piezoelectric, and Ferroelectric Properties of BZT-Modified BiFeO3-BaTiO3 Multiferroic Ceramics with MnO2 and CuO Addition

    Science.gov (United States)

    Guan, Shibo; Yang, Huabin; Chen, Guangcong; Zhang, Rui

    2018-02-01

    A new lead-free piezoelectric ceramic, 0.67BiFeO3-0.33BaTiO3-xBi(Zn0.5Ti0.5) O3 + 0.0035MnO2 + 0.004CuO, was prepared through the solid-state reaction route. The ceramic was sintered in the 950-990°C range. In this paper, the crystal structure of the sample is pure perovskite structure with a pseudo-cubic structure in the range of x = 0-0.05, and does not change greatly with the increase of x. The grain size increases first and then decreases with the increase of x. The addition of Bi(Zn0.5Ti0.5) O3(BZT) promoted the grain growth of the sample. The piezoelectric constant reached the maximum value of d 33 = 188 pC/N, electromechanical coupling coefficient k p = 0.301 and the remanent polarization P r = 61.20 μC/cm2 at x = 0.03. It has a high Curie temperature of T c = 420°C. On the other hand, the depolarization temperature reaches the maximum value, T d = 426°C, at x = 0. A small amount of BZT doping can improve the piezoelectric, dielectric, and ferroelectric properties of the samples. Therefore, this material can be considered as a promising lead-free piezoelectric ceramic material in the application field of high-temperature materials.

  9. Electric-field-induced paraelectric to ferroelectric phase transformation in prototypical polycrystalline BaTiO3

    International Nuclear Information System (INIS)

    Wang, Zhiyang; Hinterstein, Manuel; Daniels, John E.; Webber, Kyle G.; Hudspeth, Jessica M.

    2014-01-01

    An electric-field-induced paraelectric cubic to ferroelectric tetragonal phase transformation has been directly observed in prototypical polycrystalline BaTiO 3 at temperatures above the Curie point (T C ) using in situ high-energy synchrotron X-ray diffraction. The transformation persisted to a maximum temperature of 4 °C above T C . The nature of the observed field-induced transformation and the resulting development of domain texture within the induced phase were dependent on the proximity to the transition temperature, corresponding well to previous macroscopic measurements. The transition electric field increased with increasing temperature above T C , while the magnitude of the resultant tetragonal domain texture at the maximum electric field (4 kV mm −1 ) decreased at higher temperatures. These results provide insights into the phase transformation behavior of a prototypical ferroelectric and have important implications for the development of future large-strain phase-change actuator materials.

  10. Evolution of phase transformation behavior and dielectric temperature stability of BaTiO3–Bi(Zn0.5Zr0.5)O3 ceramics system

    International Nuclear Information System (INIS)

    Wang, Yiliang; Chen, Xiuli; Zhou, Huanfu; Fang, Liang; Liu, Laijun; Zhang, Hui

    2013-01-01

    Highlights: ► (1 − x)BaTiO 3 –xBi(Zn 0.5 Zr 0.5 )O 3 ceramics were synthesized. ► A systematic structural change was observed near x = 0.07 and x = 0.4. ► A change from a normal ferroelectric behavior to diffusive and dispersive relaxor-like characteristic was also observed. ► (1 − x)BT–xBZZ ceramics show good dielectric temperature stability over a wide temperature range. - Abstract: (1 − x)BaTiO 3 –xBi(Zn 0.5 Zr 0.5 )O 3 [(1 − x)BT–xBZZ, 0.01 ⩽ x ⩽ 0.6] ceramics were synthesized by solid-state reaction technique. Based on the X-ray diffraction data analysis, a systematic structure change from the ferroelectric tetragonal phase to pseudocubic phase and the pseudocubic phase to orthorhombic phase was observed near x = 0.07 and x = 0.4 at room temperature, respectively. Dielectric measurements show a dielectric anomaly, over the temperature range from 50 to 200 °C for the compositions with 0.03 ⩽ x ⩽ 0.09. A change from a normal ferroelectric behavior to diffusive and dispersive relaxor-like characteristic was also observed. Moreover, (1 − x)BT–xBZZ ceramics show good dielectric temperature stability over a wide temperature range, which indicates that these ceramics can be applied in the temperature stability devices.

  11. Substitution behavior of x(Na0.5K0.5)NbO3-(1 - x)BaTiO3 ceramics for multilayer ceramic capacitors by a near edge x-ray absorption fine structure analysis

    Science.gov (United States)

    Ha, Jooyeon; Ryu, Jiseung; Lee, Heesoo

    2014-06-01

    The doping effect of (Na0.5K0.5)NbO3 (NKN) as alternatives for rare-earth elements on the electrical properties of BaTiO3 has been investigated, in terms of their substitution behavior. The dielectric constant of a specimen with x = 0.05 was about 79% higher than that of pure BaTiO3, and the temperature coefficient of capacitance was satisfied by the X7R specification. The specimen with x = 0.05 showed the lowest tetragonality among the four compositions and had a fine grain size of x-ray absorption fine structure spectroscopy, the practical substitution behavior was defined by the change in Ti 3d orbital states. The energy separation of the Ti 3d orbitals was more apparent with the specimen of x = 0.05, which is related to the donor level from the donor substitution of Nb5+ ion for Ti-sites. Therefore, the simultaneous substitution of Na+/K+ and Nb5+ ions into BaTiO3 can improve dielectric properties, based on the charge-transfer process.

  12. Calculation of strained BaTiO3 with different exchange correlation functionals examined with criterion by Ginzburg-Landau theory, uncovering expressions by crystallographic parameters

    Science.gov (United States)

    Watanabe, Yukio

    2018-05-01

    In the calculations of tetragonal BaTiO3, some exchange-correlation (XC) energy functionals such as local density approximation (LDA) have shown good agreement with experiments at room temperature (RT), e.g., spontaneous polarization (PS), and superiority compared with other XC functionals. This is due to the error compensation of the RT effect and, hence, will be ineffective in the heavily strained case such as domain boundaries. Here, ferroelectrics under large strain at RT are approximated as those at 0 K because the strain effect surpasses the RT effects. To find effective XC energy functionals for strained BaTiO3, we propose a new comparison, i.e., a criterion. This criterion is the properties at 0 K given by the Ginzburg-Landau (GL) theory because GL theory is a thermodynamic description of experiments working under the same symmetry-constraints as ab initio calculations. With this criterion, we examine LDA, generalized gradient approximations (GGA), meta-GGA, meta-GGA + local correlation potential (U), and hybrid functionals, which reveals the high accuracy of some XC functionals superior to XC functionals that have been regarded as accurate. This result is examined directly by the calculations of homogenously strained tetragonal BaTiO3, confirming the validity of the new criterion. In addition, the data points of theoretical PS vs. certain crystallographic parameters calculated with different XC functionals are found to lie on a single curve, despite their wide variations. Regarding these theoretical data points as corresponding to the experimental results, analytical expressions of the local PS using crystallographic parameters are uncovered. These expressions show the primary origin of BaTiO3 ferroelectricity as oxygen displacements. Elastic compliance and electrostrictive coefficients are estimated. For the comparison of strained results, we show that the effective critical temperature TC under strain 1000 K from an approximate method combining ab initio

  13. Dielectric enhancement of BaTiO3/SrTiO3 superlattices with embedded Ni nanocrystals

    International Nuclear Information System (INIS)

    Xiong Zhengwei; Sun Weiguo; Wang Xuemin; Jiang Fan; Wu Weidong

    2012-01-01

    Highlights: ► The BaTiO 3 /SrTiO 3 superlattices with embedded Ni NCs were successfully fabricated by L-MBE. ► The influence with the various concentrations of Ni nanocrystals embedded in BaTiO 3 /SrTiO 3 superlattices was also discussed. ► The BaTiO 3 /SrTiO 3 superlattices with lower concentration of embedded Ni NCs had higher permittivity and dielectric loss compared with the pure BaTiO 3 /SrTiO 3 superlattices. ► The dielectric enhancement of BaTiO 3 /SrTiO 3 superlattices with embedded Ni NCs was proposed to explained by Drude quasi-free-electron theory. - Abstract: The self-organized Ni nanocrystals (NCs) were embedded in BaTiO 3 /SrTiO 3 superlattices using laser molecular beam epitaxy (L-MBE). The stress of the composite films was increased with the increasing concentration of embedded Ni NCs, as investigation in stress calculation. The influence with the various concentrations of Ni NCs embedded in BaTiO 3 /SrTiO 3 superlattices was also discussed. The internal stress of the films was too strong to epitaxial growth of BaTiO 3 /SrTiO 3 superlattices. Compared with the pure BaTiO 3 /SrTiO 3 superlattices, the BaTiO 3 /SrTiO 3 superlattices with lower concentration of embedded Ni NCs had higher permittivity and dielectric loss. Furthermore, the dielectric enhancement of BaTiO 3 /SrTiO 3 superlattices with embedded Ni NCs was proposed to explained by Drude quasi-free-electron theory.

  14. The Effect of Poling on the Properties of 0.65Pb(Mg1/3Nb2/3)O3-0.35PbTiO3 Ceramics

    Science.gov (United States)

    Uršič, Hana; Tellier, Jenny; Hrovat, Marko; Holc, Janez; Drnovšek, Silvo; Bobnar, Vid; Alguero, Miguel; Kosec, Marija

    2011-03-01

    The effects of the poling field on the structural and electrical properties of 0.65Pb(Mg1/3Nb2/3)O3-0.35PbTiO3 (0.65PMN-0.35PT) ceramics were investigated. The highest piezoelectric coefficient d33, coupling coefficients kp, kt, and mechanical quality factor Qm were achieved for ceramics poled at electric fields between 2 and 3.5 kV/mm, whereas the d33, kp, kt, and Qm of ceramics poled at higher electric fields, i.e., 4 and 4.5 kV/mm, were lower. The non-poled ceramics contained 86% of the monoclinic phase with the space group Pm and 14% of the tetragonal phase with the space group P4mm. However, the ceramics poled at 2.5 kV/mm contained 99% of the monoclinic phase and the rest is the tetragonal phase. The results show that the ratio of the monoclinic to the tetragonal phases can be changed by the application of a poling electric field and that the extent of this change is dependent on the field strength.

  15. Orientation dependence of magnetoelectric coefficient in 1-3-type BaTiO3/CoFe2O4

    Science.gov (United States)

    Jian, Gang; Shao, Hui; Zhang, Cheng; Yan, Chao; Zhao, Ning; Song, Bo; Wong, C. P.

    2018-03-01

    Orientation dependence of magnetoelectric coefficient αE33 in 1-3-type BaTiO3/CoFe2O4 composites was calculated in arbitrary directions by three-dimensional coordinate transformation method. The space distributions of pc11‧, pc12‧, e31‧ for piezoelectric phase and mc11‧, mc12‧, q31‧ for magnetic phase were obtained independently using relative experimental data and original matrices for 4mm BaTiO3 and m3m CoFe2O4. Elastic stiffness coefficients show little orientation differences, while e31‧ and q31‧ exhibit high dependence on crystal orientation, with the MAX absolute e31‧ = 2.96 C/m2 and the MAX q31‧ = 556 × 10-12 m/A are found at θ = 0° and θ = 0°, ϕ = 45°, respectively. For space distribution of αE33‧, BaTiO3||[0 0 1]/CoFe2O4||[0 0 1] combination has the maximum value which applies to both 1-3 p/m (1.485 V/A) and 1-3 m/p composites (1.529 V/A). Volume fraction is quite independent of orientations of both piezoelectric and magnetic phases and the volume fraction for magnetic phase f around 0.5 obtains the largest αE33. The results suggest an approach to significantly enhancing magnetoelectric coefficient of composite multiferroic materials through crystal orientation controls of single crystals and textured ceramics.

  16. Reduced energy loss in poly(vinylidene fluoride) nanocomposites by filling with a small loading of core-shell structured BaTiO3/SiO2 nanofibers

    Science.gov (United States)

    Liu, Shaohui; Xue, Shuangxi; Shen, Bo; Zhai, Jiwei

    2015-07-01

    Homogeneous ceramic-polymer nanocomposites consisting of core-shell structured BaTiO3/SiO2 nanofibers and a p oly(vinylidene fluoride) (PVDF) polymer matrix have been prepared. The correlation between the energy discharged density and interfacial polarization is studied in PVDF nanocomposites by the measurements of the discharge performance and impedance spectroscopy. According to the results of dielectric constant, breakdown strength, and complex impedance analysis, coating SiO2 layers on the surface of BaTiO3 nanofibers can block the movement of charge carriers through the nanocomposites by playing a shielding role on the charge-rich inter layer, which resulted in weak Maxwell-Wagner-Sillars interfacial polarization and thus reduces the energy loss and improved the energy discharged density of the nanocomposites. The energy discharged density in the nanocomposite with 2.5 vol. % BaTiO3/SiO2 core-shell nanofibers is 6.28 J/cm3 at 3.3 MV/cm, which is over 11.94% higher than that of nanocomposite with BaTiO3 nanofibers at the same electric field.

  17. Protocol of thermal treatments for the recovery of tetragonal phase in infrastructures of dental prostheses base of ZrO_2 (3-Y_2O_3) mills in CAD / CAM systems or panthories

    International Nuclear Information System (INIS)

    Simba, B.G.; Ferreira, B.; Santos, C.

    2011-01-01

    ZrO_2(3%Y_2O_3) bioceramics are used as dental materials mainly as prosthesis components, because present high mechanical properties and translucence. The use of CAD/CAM machining technique needs final grinding which promotes tetragonal monoclinic transformation reducing the reliability of this ceramic. In this work, ZrO_2(3%Y_2O_3) ceramics were sintered at 1450-0h, 1530-2h or 1600-4h and characterized. Different heat-treatment (400-1200 deg C) are proposed aiming the recuperation of the tetragonal crystalline phase. (author)

  18. Structural and electrical characterization of (BaTiO3)x(La0.67Sr0.33MnO3)1-x ceramic composites

    International Nuclear Information System (INIS)

    Gaffoor, Abdul; Ravinder, D.; Joshi, U.S.; Mistry, B.V.; Joshi, Nikhail G.; Chayya, U.V.; Gadhvi, M.R.

    2012-01-01

    Multiferroic materials with the coexistence of at least two ferroic orders (ferroelectric, (anti-)ferromagnetic, and ferroelastic) have recently drawn ever-increasing interest due to their potential for applications as multifunctional devices. Among them, the coexistence of ferroelectricity and ferromagnetism is highly desired. But only their coexistence is not enough; of most important is to require a strong coupling interaction between two ferroic orders. Ceramic composite of well known ferromagnetic metallic manganite La 0.67 Sr 0.33 MnO 3 (LSMO) is systematically substituted by ferroelectric oxide BaTiO 3 (BTO). Samples with generic formula (BTO) x (LSMO) 1-x (x = 0.0 to 1.0, in step of 0.2) were synthesized by standard double sintering method. XRD show major perovskite LSMO phase upto x=0.6. However mixed phases were detected for almost all the x value except end points. Temperature dependent DC resistivity exhibit systematic metallic to insulator transformation with increasing x. Frequency dependent dielectric constants show a linear decrease over 10 MHz, whereas the loss tangent found to increase abnormally with frequency, with increasing x. Electric field dependent polarization show a broad hysteresis for x e' 0.6. (author)

  19. Structure and properties of plasma sprayed BaTiO(3) coatings: Spray parameters versus structure and photocatalytic activity

    Czech Academy of Sciences Publication Activity Database

    Ctibor, Pavel; Ageorges, H.; Štengl, Václav; Murafa, Nataliya; Píš, I.; Zahoranová, T.; Nehasil, V.; Pala, Zdeněk

    2011-01-01

    Roč. 37, č. 7 (2011), s. 2561-2567 ISSN 0272-8842 R&D Projects: GA AV ČR IAAX00430803 Institutional research plan: CEZ:AV0Z20430508; CEZ:AV0Z40320502 Keywords : Spectroscopy * Optical properties * BaTiO3 * Plasma spraying * Photocatalysis Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass Impact factor: 1.751, year: 2011 http://www.sciencedirect.com/science/article/pii/S0272884211002173

  20. Hydrothermal degradation of tetragonal ZrO2 ceramic components used in dental applications

    International Nuclear Information System (INIS)

    Mukaeda, L.E.; Robin, A.; Taguchi, S.P.

    2009-01-01

    With the evolution of the dental restoration techniques, a considerable growth in the demand of ceramic products occurred. These materials present good strength associated to reliability. In this work, micrometric and nanometric scale tetragonal ZrO 2 blocks were sintered at 1500 deg C-2h and 1350 deg C-2h, respectively, ground and polished. Ceramics with relative density higher than 98% were obtained. The specimens were immersed in hot water (150 deg C), for times ranging from 10h to 30h. The mass variation of the samples was measured and the crystalline phases present before and after the degradation tests were identified by X-ray diffractometry, in order to evaluate the capacity of these ceramics in resisting to aqueous medium exposure. Materials with nanometric structure present higher resistance to degradation than those with micrometric scale, and this interferes in structural stability after the test, and reduces the martensitic transformation. (author)

  1. Study of the structural and electrical behavior of Bi(Mg,TiO3 modified (Ba,CaTiO3 ceramics

    Directory of Open Access Journals (Sweden)

    Md. Kashif Shamim

    2016-12-01

    Full Text Available The ability of BaTiO3 to form solid solutions with different dopants (both iso- and aliovalent makes it versatile for various applications. In the present study, (Ba,CaTiO3 (BCT is modified with Bi(MgTiO3 (BMT in search for new lead-free ferroelectric material and improve their properties. For this purpose, BCT acts as a main base material and BMT acts as a modifier to fabricate a multifunctional material. In this study, we report the structural and electrical properties of lead free piezo-ceramics (1−x(Ba0.8Ca0.2TiO3–xBi(Mg0.5Ti0.5O3 with x=0.2, 0.4, 0.5 prepared by solid-state sintering technique. Single perovskite phase with tetragonal structure is obtained for all the compositions, which is reconfirmed by the Raman Spectroscopic study. Dielectric study confirm the temperature stable behavior of the dielectric permittivity values above 300∘C. The dielectric constant value decreases with increase in BMT doping content. Impedance Spectroscopic study confirms non-Debye type dielectric relaxation in the specimen. The Nyquist plot and conductivity studies show the negative temperature coefficient of resistance behavior (NTCR of the samples.

  2. Protocol of thermal treatments for the recovery of tetragonal phase in infrastructures of dental prostheses base of ZrO{sub 2} (3-Y{sub 2}O{sub 3}) mills in CAD / CAM systems or panthories; Protocolo de tratamentos termicos visando recuperacao da fase tetragonal em infraestruturas de proteses dentarias a base de ZrO{sub 2}(3-Y{sub 2}O{sub 3}) fresadas em sistemas CAD/CAM ou pantografos

    Energy Technology Data Exchange (ETDEWEB)

    Simba, B.G.; Ferreira, B.; Santos, C. [Universidade de Sao Paulo (EEL/USP), Lorena, SP (Brazil). Escola de Engenharia; Costa, L. [Centro Universitario de Volta Redonda (MeMAT/UNIFOA), RJ (Brazil). Pro-Reitoria de Pesquisa e Extensao; Sa, L.F.C. de, E-mail: brgalvao@yahoo.com.br [PROTMAT Materiais Avancados, Volta Redonda, RJ (Brazil)

    2011-07-01

    ZrO{sub 2}(3%Y{sub 2}O{sub 3}) bioceramics are used as dental materials mainly as prosthesis components, because present high mechanical properties and translucence. The use of CAD/CAM machining technique needs final grinding which promotes tetragonal monoclinic transformation reducing the reliability of this ceramic. In this work, ZrO{sub 2}(3%Y{sub 2}O{sub 3}) ceramics were sintered at 1450-0h, 1530-2h or 1600-4h and characterized. Different heat-treatment (400-1200 deg C) are proposed aiming the recuperation of the tetragonal crystalline phase. (author)

  3. Atomic profile imaging of ceramic oxide surfaces

    International Nuclear Information System (INIS)

    Bursill, L.A.; Peng JuLin; Sellar, J.R.

    1989-01-01

    Atomic surface profile imaging is an electron optical technique capable of revealing directly the surface crystallography of ceramic oxides. Use of an image-intensifier with a TV camera allows fluctuations in surface morphology and surface reactivity to be recorded and analyzed using digitized image data. This paper reviews aspects of the electron optical techniques, including interpretations based upon computer-simulation image-matching techniques. An extensive range of applications is then presented for ceramic oxides of commercial interest for advanced materials applications: including uranium oxide (UO 2 ); magnesium and nickel oxide (MgO,NiO); ceramic superconductor YBa 2 Cu 3 O 6.7 ); barium titanate (BaTiO 3 ); sapphire (α-A1 2 O 3 ); haematite (α-Fe-2O 3 ); monoclinic, tetragonal and cubic monocrystalline forms of zirconia (ZrO 2 ), lead zirconium titanate (PZT + 6 mol.% NiNbO 3 ) and ZBLAN fluoride glass. Atomic scale detail has been obtained of local structures such as steps associated with vicinal surfaces, facetting parallel to stable low energy crystallographic planes, monolayer formation on certain facets, relaxation and reconstructions, oriented overgrowth of lower oxides, chemical decomposition of complex oxides into component oxides, as well as amorphous coatings. This remarkable variety of observed surface stabilization mechanisms is discussed in terms of novel double-layer electrostatic depolarization mechanisms, as well as classical concepts of the physics and chemistry of surfaces (ionization and affinity energies and work function). 46 refs., 16 figs

  4. Self-Organized Ni Nanocrystal Embedded in BaTiO3 Epitaxial Film

    Directory of Open Access Journals (Sweden)

    Ge FF

    2010-01-01

    Full Text Available Abstract Ni nanocrystals (NCs were embedded in BaTiO3 epitaxial films using the laser molecular beam epitaxy. The processes involving the self-organization of Ni NCs and the epitaxial growth of BaTiO3 were discussed. With the in situ monitoring of reflection high-energy electron diffraction, the nanocomposite films were engineered controllably by the fine alternation of the self-organization of Ni NCs and the epitaxial growth of BaTiO3. The transmission electron microscopy and the X-ray diffraction characterization confirmed that the composite film consists of the Ni NCs layers alternating with the (001/(100-oriented epitaxial BaTiO3 separation layers.

  5. Improvement of β-phase crystal formation in a BaTiO3-modified PVDF membrane

    Science.gov (United States)

    Lin, SHEN; Lei, GONG; Shuhua, CHEN; Shiping, ZHAN; Cheng, ZHANG; Tao, SHAO

    2018-04-01

    In this paper, low temperature plasma is used to modify the surface of barium titanate (BaTiO3) nanoparticles in order to enhance the interfacial compatibility between ferroelectric poly(vinylidene fluoride) (PVDF) and BaTiO3 nanoparticles. The results demonstrate that oxygenic groups are successfully attached to the BaTiO3 surface, and the quantity of the functional groups increases with the treatment voltage. Furthermore, the effect of modified BaTiO3 nanoparticles on the morphology and crystal structure of the PVDF/BaTiO3 membrane is investigated. The results reveal that the dispersion of BaTiO3 nanoparticles in the PVDF matrix was greatly improved due to the modification of the BaTiO3 nanoparticles by air plasma. It is worth noting that the formation of a β-phase in a PVDF/modified BaTiO3 membrane is observably promoted, which results from the strong interaction between PVDF chains and oxygenic groups fixed on the BaTiO3 surface and the better dispersion of BaTiO3 nanoparticles in the PVDF matrix. Besides, the PVDF/modified BaTiO3 membrane at the treatment voltage of 24 kV exhibits a lower water contact angle (≈68.4°) compared with the unmodified one (≈86.7°). Meanwhile, the dielectric constant of PVDF/BaTiO3 nanocomposites increases with the increase of working voltage.

  6. Temperature coefficient of piezoelectric constants in Pb(Mg1/3 Nb2/3O3 - PbTiO3 ceramics

    Directory of Open Access Journals (Sweden)

    Manuel Henrique Lente

    2004-06-01

    Full Text Available In this work, the thermal stability of piezoelectric constants of PMN-PT ceramics in the tetragonal and rhombohedral phases were investigated in a wide range of temperatures. The results showed that the tetragonal PMN-PT presented higher thermal stability and, consequently, the temperature coefficients for the piezoelectric constants were approximately zero. This result revealed to be much better than that commonly found for PZT ceramics. Although the rhombohedral PMN-PT presented a slight lower thermal stability, the values found for the coupling factor were significantly higher than the tetragonal composition.

  7. Dielectric behaviour of (Ba,Sr)TiO3 perovskite borosilicate glass ceramics

    International Nuclear Information System (INIS)

    Yadav, Avadhesh Kumar; Gautam, C.R.

    2013-01-01

    Various perovskite (Ba,Sr)TiO 3 borosilicate glasses were prepared by rapid melt-quench technique in the glass system ((Ba 1-x Sr x ).TiO 3 )-(2SiO 2 .B 2 O 3 )-(K 2 O)-(La 2 O 3 ). On the basis of differential thermal analysis results, glasses were converted into glass ceramic samples by regulated heat treatment schedules. The dielectric behaviour of crystallized barium strontium titanate borosilicate glass ceramic samples shows diffuse phase transition. The study depicts the dielectric behaviour of glass ceramic sample BST5K1L0.2S814. The double relaxation was observed in glass ceramic samples corresponding 80/20% Ba/Sr due to change in crystal structure from orthorhombic to tetragonal and tetragonal to cubic with variation of temperature. The highest value of dielectric constant was found to be 48289 for the glass ceramic sample BST5K1L0.2S814. The high value of dielectric constant attributed to space charge polarization between the glassy phase and perovskite phase. Due to very high value of dielectric constant, such glass ceramics are used for high energy storage devices. La 2 O 3 acts as nucleating agent for crystallization of glass to glass ceramics and enhances the dielectric constant and retarded dielectric loss. Such glass ceramics can be used in high energy storage devices such as barrier layer capacitors, multilayer capacitors etc. (author)

  8. Large electrical manipulation of permittivity in BaTiO3 and Pb(Zr,Ti)O3 bimorph heterostructure

    International Nuclear Information System (INIS)

    Ci, Penghong; Liu, Guoxi; Dong, Shuxiang; Zhang, Li

    2014-01-01

    We report a strain-mediated electric field manipulation of permittivity in BaTiO 3 (barium titanate, BT) ceramic by a Pb(Zr,Ti)O 3 (PZT) bimorph. This BT/PZT heterostructure exhibited a relatively large permittivity tunability of BT up to ±10% in a wide frequency range under an electric field of ±4 kV/cm applied to the PZT bimorph. The permittivity tunability is attributed to the strain in BT produced by the PZT bimorph. Calculations of the relationship between permittivity and applied electric field were developed, and corresponded well with measurements. The BT/PZT heterostructure has potential for applications in broadband field tunable smart electronic devices.

  9. Estudio del perfil de defectos y de las propiedades eléctricas de BaTiO3 dopado con Nb y La

    Directory of Open Access Journals (Sweden)

    Castro, M. S.

    2002-02-01

    Full Text Available The aim of this work is to study the impact of two different and typical donor –dopants; Nb2O5 and La2O3, on the electrical properties of BaTiO3. Besides, the influence of Nb5+ and La3+ on the charge compensation mechanism was evaluated. On this way, it was determined that, the defect structure is not only affected by the dopant ion but also by its concentration. Amount of dopant also affects the electrical properties of BaTiO3 ceramics. In fact, for low Nb2O5 or La2O3 concentration, electronic compensation prevails, leading to a low – resistive material with an important PTCR effect. By EPR an increases in the oxygen vacancies with a low lanthanum addition was determined. This phenomenon could be associated to the lanthanum acceptor behavior. On the other hand, high dopant concentration leads to a high – resistive material showing GBBL characteristics. In this case, a high content of double – ionized barium vacancies able to trap electrons, and a thin glassy – phase film covering the BaTiO3 grains lead to a high – resistive material. This phenomenon encourages the hypothesis in which barium vacancies act as acceptor centers at the grain boundaries in BaTiO3 ceramics.En este trabajo, se estudia el impacto de la adición de Nb2O5 o La2O3 sobre las propiedades eléctricas de cerámicos basados en BaTiO3. Asimismo, se estudia la influencia de estos dos típicos dopantes en los mecanismos de compensación de cargas. En este sentido, se ha determinado que la estructura de defectos en el BaTiO3 no sólo se encuentra afectada por el tipo de dopante sino tambien por su concentración. En efecto, para bajas concentraciones de Nb2O5 o La2O3, predomina un mecanismo de compensación de cargas por generación de electrones. Sin embargo, los resultados de EPR muestran que la adición de una pequeña cantidad de La2O3 produce un notable incremento en la concentración de vacantes de oxígeno respecto del BaTiO3 sin dopar. Este fenómeno podr

  10. Combined mode I-mode II fracture of 12-mol%-ceria-doped tetragonal zirconia polycrystalline ceramic

    International Nuclear Information System (INIS)

    Tikare, V.; Choi, S.R.

    1997-01-01

    The mode I, mode II, and combined mode I-mode II fracture behavior of ceria-doped tetragonal zirconia polycrystalline (Ce-TZP) ceramic was studied. The single-edge-precracked-beam (SEPB) samples were fractured using the asymmetric four-point-bend geometry. The ratio of mode I to mode II loading was varied by varying the degree of asymmetry in the four-point-bend geometry. The minimum strain energy density theory best described the mixed-mode fracture behavior of Ce-TZP with the mode I fracture toughness, K IC = 8.2 ± 0.6 MPa·m 1/2 , and the mode II fracture toughness, K IIC = 8.6 ± 1.3 MPa·m 1/2

  11. Solution based approaches for the morphology control of BaTiO3 particulates

    Directory of Open Access Journals (Sweden)

    Florentina Maxim

    2010-09-01

    Full Text Available Within the action COST 539 - ELENA our contribution was aimed at studying solution based approaches for the morphology control of BaTiO3 particulates. Initially, our kinetic analysis and systematic structural and morphological studies, demonstrated that during hydrothermal synthesis from layered titanate nanotubes (TiNTS, BaTiO3 forms via two mechanisms depending on the temperature and time. At low temperatures (90°C, “wild” type BaTiO3 dendritic particles with cubic structure were formed through a phase boundary topotactic reaction. At higher temperatures and/or for longer times time, the reaction is controlled by a dissolution precipitation mechanism and “seaweed” type BaTiO3 dendrites are formed. Our results unambiguously elucidated why TiNTs do not routinely act as templates for the formation of 1D BaTiO3.In our subsequent investigations, the effect of additives on the aqueous and hydrothermal synthesis of BaTiO3 was assessed. We reported that although the tested additives influenced the growth of BaTiO3, their behaviour varied; poly(acrylic acid (PAA adsorbed on specific crystallographic faces changing the growth kinetics and inducing the oriented attachment of the particles; poly(vinyl pyrrolidone (PVP, sodium dodecylsulfate (SDS and hydroxypropylmethylcellulose (HPMC act as growth inhibitors rather than crystal habit modifiers; and DFructose appeared to increase the activation energy for nucleation, resulting in small crystals (26 nm. Our work clearly indicates that the synthesis of 1D nanostructures of complex oxides by chemical methods is non trivial.

  12. Conduction Mechanisms in Multiferroic Multilayer BaTiO3/NiFe2O4/BaTiO3 Memristors

    Science.gov (United States)

    Samardzic, N.; Bajac, B.; Srdic, V. V.; Stojanovic, G. M.

    2017-10-01

    Memristive devices and materials are extensively studied as they offer diverse properties and applications in digital, analog and bio-inspired circuits. In this paper, we present an important class of memristors, multiferroic memristors, which are composed of multiferroic multilayer BaTiO3/NiFe2O4/BaTiO3 thin films, fabricated by a spin-coating deposition technique on platinized Si wafers. This cost-effective device shows symmetric and reproducible current-voltage characteristics for the actuating voltage amplitude of ±10 V. The origin of the conduction mechanism was investigated by measuring the electrical response in different voltage and temperature conditions. The results indicate the existence of two mechanisms: thermionic emission and Fowler-Nordheim tunnelling, which alternate with actuating voltage amplitude and operating temperature.

  13. Ceramic Translations. Volume 41. Grain Boundaries and Interfacial Phenomena in Electronic Ceramics

    Science.gov (United States)

    1994-01-01

    20H -- H20(S) + 02- reaction. In situ FTIR results from our (nitric acid washed) fresh tetragonal hydrothermally -prepared BaTiO3 (alkoxide-based) sample...solution of cation composition Bi:Pb:Sr:Ca:Cu = 1.65:0.35:1.6:2:3 was made and an oxalate precipitate was formed using oxalic acid . The oxalate was...consuming fossil fuels, for example, possibly leads to a green-house effect, and by-products such as NOx and SOxcause acid rain. Accordingly, for the

  14. Two steps hydrothermal growth and characterisations of BaTiO3 films composed of nanowires

    Science.gov (United States)

    Zawawi, Che Zaheerah Najeehah Che Mohd; Salleh, Shahril; Oon Jew, Lee; Tufail Chaudhary, Kashif; Helmi, Mohamad; Safwan Aziz, Muhammad; Haider, Zuhaib; Ali, Jalil

    2018-05-01

    Barium titanate (BaTiO3) films composed of nanowires have gained considerable research interest due to their lead-free composition and strong energy conversion efficiency. BaTiO3 films can be developed with a simple two steps hydrothermal reactions, which are low cost effective. In this research, BaTiO3 films were fabricated on titanium foil through two steps hydrothermal method namely, the growth of TiO2 and followed by BaTiO3 films. The structural evolutions and the dielectric properties of the films were investigated as well. The structural evolutions of titanium dioxide (TiO2) and BaTiO3 nanowires were characterized using X-ray diffraction and scanning electron microscopy. First step of hydrothermal reaction, TiO2 nanowires were prepared in varied temperatures of 160 °C, 200 °C and 250 °C respectively. Second step of hydrothermal reaction was performed to produce a layer of BaTiO3 films.

  15. Growth and self-assembly of BaTiO3 nanocubes for resistive switching memory cells

    International Nuclear Information System (INIS)

    Chu, Dewei; Lin, Xi; Younis, Adnan; Li, Chang Ming; Dang, Feng; Li, Sean

    2014-01-01

    In this work, the self-assembled BaTiO 3 nanocubes based resistive switching memory capacitors are fabricated with hydrothermal and drop-coating approaches. The device exhibits excellent bipolar resistance switching characteristics with ON/OFF ratio of 58–70, better reliability and stability over various polycrystalline BaTiO 3 nanostructures. It is believed that the inter cube junctions is responsible for such a switching behaviour and it can be described by the filament model. The effect of film thickness on switching ratio (ON/OFF) was also investigated in details. - Graphical abstract: This work describes a novel resistive switching memory cell based on self-assembled BaTiO 3 nanocubes. - Highlights: • BaTiO 3 nanocubes were prepared by one step facile hydrothermal method. • Self-assembled BaTiO 3 nanocubes thin films were obtained by drop-coating approach. • The BaTiO 3 nanocubes show excellent resistive switching properties for memory applications

  16. Effect of mechanical milling on barium titanate (BaTiO3) perovskite

    Science.gov (United States)

    Singh, Rajan Kumar; Sanodia, Sagar; Jain, Neha; Kumar, Ranveer

    2018-05-01

    Commercial Barium Titanate BaTiO3 (BT) is milled by planetary ball mill in acetone medium using stainless steel bowl & ball for different hours. BT is an important perovskite oxide with structure ABO3. BT has applications in electro-optic devices, energy storing devices such as photovoltaic cells, thermistors, multiceramic capacitors & DRAMs etc. BT is non-toxic & environment friendly ceramic with high dielectric and piezoelectric property so it can be used as the substitute of PZT & PbTiO3. Here, we have investigated the effect of milling time and temperature on particle size and phase transition of BT powder. We used use Raman spectroscopy for studying the spectra of BT; XRD is used for structural study. Intensity (height) of Raman spectra and XRD spectra continuously decrease with increasing the milling hours and width if these spectra increases which indicates, decrease in BT size.

  17. Synthesis and luminescence properties of BaTiO3:RE (RE = Gd , Dy ...

    Indian Academy of Sciences (India)

    thermoluminescence (TL) properties of BaTiO3 samples doped with Gd3+, Dy3+, Tb3+ and Lu3+ were investigated. ... electron microscope using an accelerating voltage of 20 kV. .... doping of 1% mole Gd3+ ion into the BaTiO3 compound.

  18. Tetragonal zirconia ceramics in Zr O2-Ce O2 system (Ce-TZP): preparation, characterization and mechanical properties

    International Nuclear Information System (INIS)

    Andrade Nono, M.C. de.

    1992-01-01

    This paper describes and discusses the results achieved in a study about Ce-TZP ceramics prepared from conventional powder mixtures of Zr O 2 and Ce O 2 (with composition in the range of 8 to 16 mol% Ce O 2 ). Physical and chemical characteristics were related with the powder compaction behavior and with the sintering state. The sintered ceramics showed a level of high porosity (≅ 4%), mainly due to the fairly adequate powder characteristics and compaction. The crystalline phases were analysed from X-rays diffraction data and showed that these ceramics can present tetragonal-to-monoclinic stress induced transformation. The bending strength, fracture toughness and Vickers hardness results were influenced by Ce O 2 content microstructure and sintering temperature. These Ce-TZP ceramics showed mechanical strength results comparable to those published in the international literature. (author)

  19. Hydrothermal–galvanic couple synthesis of directionally oriented BaTiO3 thin films on TiN-coated substrates

    International Nuclear Information System (INIS)

    Yang, Chia-Jung; Tsai, Di-You; Chan, Pei-Hsuan; Wu, Chu-Tsun; Lu, Fu-Hsing

    2013-01-01

    BaTiO 3 films were synthesized on TiN-coated Si substrate below 100 °C by a hydrothermal–galvanic couple technique in barium contained alkaline solutions. X-ray diffraction and electron backscatter diffraction results show that the BaTiO 3 thin films were directionally oriented grown on the TiN/Si substrates, i.e., (111) BaTiO 3 over (111) TiN. The surface morphologies revealed that BaTiO 3 nucleated and grew over the TiN surface with a single layer. From kinetic analyses, the growth rates of BaTiO 3 films prepared by the hydrothermal–galvanic couple technique were faster than a hydrothermal method. The galvanic effects were confirmed by investigating the induced currents and energies. The galvanic currents were generated and controlled by both the dissolution of TiN and the formation of BaTiO 3 . The output electric energies increased rapidly with the reaction time and leveled off at the full coverage of BaTiO 3 . - Highlights: • Cubic BaTiO 3 films are synthesized by a hydrothermal–galvanic couple method (HT–GC). • Growth rates of BaTiO 3 films made by HT–GC are faster than a hydrothermal method. • BaTiO 3 films are directionally oriented grown on the TiN/Si substrates. • Galvanic currents are controlled by dissolution of TiN and formation of BaTiO 3

  20. (Nd0⋅065Ti0⋅87Nb0⋅065)O3 ceramic

    Indian Academy of Sciences (India)

    Unknown

    Polycrystalline ceramic samples of sodium bismuth titanate with simultaneous doping at A and B sites have been studied for the influence of ... of Nd and Nb at B site in BaTiO3 (BaNdxTi1–2xNbxO3). (Mahboob et al 2005a). Dielectric ..... hence the conduction arises due to short range translation hopping via large polarons.

  1. BiFeO3-doped (Na0.5K0.5NbO3 lead-free piezoelectric ceramics

    Directory of Open Access Journals (Sweden)

    Xueyi Sun et al

    2008-01-01

    Full Text Available Lead-free piezoelectric ceramics (1−x(Na0.5K0.5NbO3-xBiFeO3 (x=0~0.07 were synthesized by the solid-state reaction. Differential scanning calorimetry (DSC measurements revealed that an increase in the amount of BiFeO3 dopant resulted in a decrease in the orthorhombic-tetragonal and tetragonal-cubic phase transition temperature of the material. One percent BiFeO3 additive suppressed grain growth, which not only benefits the sintering of ceramics but also enhances the piezoelectric and ferroelectric properties, where d33=145pC/N, kp=0.31, Qm=80, Pr=11.3 μC cm−2 and Ec=16.5 kV cm−1. As xBF>0.01, both piezoelectric and ferroelectric properties decreased rapidly with an increasing amount of dopant.

  2. Ferroelectric properties of NaNbO3-BaTiO3 thin films deposited on SrRuO3/(001)SrTiO3 substrate by pulsed laser deposition

    International Nuclear Information System (INIS)

    Yamazoe, Seiji; Oda, Shinya; Sakurai, Hiroyuki; Wada, Takahiro; Adachi, Hideaki

    2009-01-01

    (NaNbO 3 ) 1-x (BaTiO 3 ) x (NN-xBT) thin films with low BaTiO 3 (BT) concentrations x (x=0.05 and 0.10) were fabricated on SrRuO 3 /(001)SrTiO 3 (SRO)/(001)STO) substrate by pulsed laser deposition (PLD). X-ray diffraction pattern (XRD) and transmission electron diffraction pattern (TED) showed that NN-0.10BT thin film was epitaxially grown on SRO/(001)STO substrate with a crystallographic relationship of [001] NN-xBT parallel [001] STO . From reciprocal space maps, the lattice parameters of the out-of-plane direction of NN-xBT thin films became larger with an increase in BT concentration, although the lattice parameter of the in-plane was hardly changed by the BT concentration. The value of relative dielectric constant ε r of the NN-xBT thin films were increased with BT concentration. The ε r and the dielectric loss tanδ of NN-0.10BT were 1220 and 0.02 at 1 kHz, respectively. The P-E hysteresis loops of the NN-xBT thin films showed clear ferroelectricity. Although the value of remanent polarization P r decreased with the BT concentration, the behaviors of ε r , P r , and coercive electric field E c of the NN-xBT thin films against the BT concentration accorded with those of NN-xBT ceramics, in which NN-0.10BT ceramics exhibited the largest piezoelectric property. Therefore, the NN-0.10BT thin film is expected to show high piezoelectricity. (author)

  3. Pulse-based electron spin transient nutation measurement of BaTiO3 fine particle: Identification of controversial signal around g = 2.00

    Science.gov (United States)

    Sawai, Takatoshi; Yamaguchi, Yoji; Kitamura, Noriko; Date, Tomotsugu; Konishi, Shinya; Taga, Kazuya; Tanaka, Katsuhisa

    2018-05-01

    Two dimensional pulse-based electron spin transient nutation (2D-ESTN) spectroscopy is a powerful tool for determining the spin quantum number and has been applied to BaTiO3 fine powder in order to identify the origin of the continuous wave electron spin resonance (CW-ESR) signal around g = 2.00. The signal is frequently observed in BaTiO3 ceramics, and the correlation between the signal intensity and positive temperature coefficient of resistivity (PTCR) properties has been reported to date. The CW-ESR spectrum of BaTiO3 fine particles synthesized by the sol-gel method shows a typical asymmetric signal at g = 2.004. The 2D-ESTN measurements of the sample clearly reveal that the signal belongs to the S = 5/2 high spin state, indicating that the signal is not due to a point defect as suggested by a number of researchers but rather to a transition metal ion. Our elemental analysis, as well as previous studies, indicates that the origin of the g = 2.004 signal is due to the presence of an Fe3+ impurity. The D value (second-order fine structure parameter) reveals that the origin of the signal is an Fe3+ center with distant charge compensation. In addition, we show a peculiar temperature dependence of the CW-ESR spectrum, suggesting that the phase transition behavior of a BaTiO3 fine particle is quite different from that of a bulk single crystal. Our identification does not contradict a vacancy-mediated mechanism for PTCR. However, it is incorrect to use the signal at g = 2.00 as evidence to support the vacancy-mediated mechanism.

  4. Effects of thermal and electrical histories on structure and dielectric behaviors of (Li0.5Nd0.52+-modified (Bi0.5Na0.5TiO3-BaTiO3 ceramics

    Directory of Open Access Journals (Sweden)

    Jiwen Xu

    2017-06-01

    Full Text Available The effect of thermal and electrical histories on structure and dielectric behaviors is studied using 0.95(Bi0.5Na0.50.97(Li0.5Nd0.50.03TiO3-0.05BaTiO3 (abbreviated as BNTLN0.03-BT5 ceramic as a selected system. Subtle structure change caused by annealing treatment, and pronounced phase transition and domain switching by electrical poling, are observed to occur, respectively. The dielectric constant and its strong frequency dispersion in unpoled samples decrease evidently by electrical poling due to electric field-induced ordered domain. The high temperature Maxwell-Wagner relaxor behavior vanishes by annealing treatment due to the loss of electrical inhomogeneity with interface charging effects. Piezoelectric properties are improved evidently by annealing treatment at 900 °C, implying a new appropriate method to improve piezoelectric properties.

  5. DIELECTRIC AND PYROELECTRIC PROPERTIES OF THE COMPOSITES OF FERROELECTRIC CERAMIC AND POLY(VINYL CHLORIDE

    Directory of Open Access Journals (Sweden)

    M.Olszowy

    2003-01-01

    Full Text Available The dielectric and pyroelectric properties of lead zirconate titanate/poly(vinyl chloride [PZT/PVC] and barium titanate/poly(vinyl chloride [BaTiO3/ PVC] composites were studied. Flexible composites were fabricated in the thin films form (200-400 μm by hot-pressed method. Powders of PZT or BaTiO3 in the shape of ≤ 75 μm ceramics particles were dispersed in a PVC matrix, providing composites with 0-3} connectivity. Distribution of the ceramic particles in the polymer phase was examined by scanning electron microscopy. The analysis of the thermally stimulated currents (TSC have also been done. The changes of dielectric and pyroelectric data on composites with different contents of ceramics up to 40% volume were investigated. The dielectric constants were measured in the frequency range from 600 Hz to 6 MHz at room temperature. The pyroelectric coefficient for BaTiO3/PVC composite at 343 K is about 35 μC/m2K which is higher than that of β-PVDF (10 μC/m2 K.

  6. Structural characterization and dielectric properties of BaTiO3 thin films obtained by spin coating

    Directory of Open Access Journals (Sweden)

    Branimir Bajac

    2014-12-01

    Full Text Available Barium titanate thin films were prepared by spin coating deposition technique of an acetic precursor sol and sintered at 750, 900 and 1050 °C. Phase composition of the obtained thin films was characterized by X-ray diffraction and Raman spectroscopy. Their morphology was analysed by scanning electron microscopy and atomic force microscopy. Dielectric properties of thin films sintered at 750 and 900 °C were characterized by LCD device, where the influence of sintering temperature on dielectric permittivity and loss tangent was inspected. It was concluded that higher sintering temperature increases grain size and amount of tetragonal phase, hence higher relative permittivity was recorded. The almost constant relative permittivity in the measured frequency (800 Hz–0.5 MHz and temperature (25–200 °C ranges as well as low dielectric loss are very important for the application of BaTiO3 films in microelectronic devices.

  7. Spall strength, dynamic elastic limit and fracture of ittrya dopped tetragonal zirconia

    Science.gov (United States)

    Milyavskiy, Vladimir; Savinykh, Andrey; Schlothauer, Thomas; Lukin, Evgeny; Akopov, Felix

    2013-06-01

    Specimens of the ceramics based on zirconia partially stabilized by yttrium oxide of the composition of 97 mol % ZrO2 + 3 mol % Y2O3 were prepared. The densities of the specimens were 5.79 and 6.01 g/cc. The ceramics mainly have the tetragonal structure (93-98 wt. % of t-ZrO2) . The mechanical action on the ceramic activates the transformation of the tetragonal phase into the monoclinic one: at the abrasive cutting or at the fracture by hammer shock, the content of the monoclinic phase is increasing. The same trend was observed in the specimens, recovered after stepwise shock compression up to 36, 52 and 99 GPa. It was found that shock compression do not initiates tetragonal-monoclinic phase transition directly, and this transition is caused by the destruction. Recovered specimens do not reveal any traces of the phase change which was observed by Mashimo et al. under the pressures 30-35 GPa (J. Appl. Phys. 1995. V. 77. P. 5069). Recording of the profiles of the free surface velocity of the specimens during single-stage shock compression allowed us to determine the dynamic elastic limit, as well as spall strength of the material versus maximal shock stress. In addition, the ceramics were subjected to the action of low temperatures. There were no significant changes in the specimens recovered after storage in liquid nitrogen and helium. The work was supported by The State Atomic Energy Corporation ROSATOM.

  8. Doped barium titanate nanoparticles

    Indian Academy of Sciences (India)

    Wintec

    nese doped BaTiO3 ceramics, sintered at 1400°C in air, changes from tetragonal to hexagonal between 0⋅5 and. 1⋅7 mole% of manganese (Langhammer et al 2000). As a driving force of the transformation from the cubic to the hexagonal crystal structure, the influence of the Jahn–. Teller distortion is proposed. The grain ...

  9. Dielectric properties of (K0.5Na0.5)NbO3-(Bi0.5Li0.5)ZrO3 lead-free ceramics as high-temperature ceramic capacitors

    Science.gov (United States)

    Yan, Tianxiang; Han, Feifei; Ren, Shaokai; Ma, Xing; Fang, Liang; Liu, Laijun; Kuang, Xiaojun; Elouadi, Brahim

    2018-04-01

    (1 - x)K0.5Na0.5NbO3- x(Bi0.5Li0.5)ZrO3 (labeled as (1 - x)KNN- xBLZ) lead-free ceramics were fabricated by a solid-state reaction method. A research was conducted on the effects of BLZ content on structure, dielectric properties and relaxation behavior of KNN ceramics. By combining the X-ray diffraction patterns with the temperature dependence of dielectric properties, an orthorhombic-tetragonal phase coexistence was identified for x = 0.03, a tetragonal phase was determined for x = 0.05, and a single rhombohedral structure occurred at x = 0.08. The 0.92KNN-0.08BLZ ceramic exhibits a high and stable permittivity ( 1317, ± 15% variation) from 55 to 445 °C and low dielectric loss (≤ 6%) from 120 to 400 °C, which is hugely attractive for high-temperature capacitors. Activation energies of both high-temperature dielectric relaxation and dc conductivity first increase and then decline with the increase of BLZ, which might be attributed to the lattice distortion and concentration of oxygen vacancies.

  10. Structural study on cubic-tetragonal transition of CH3NH3PbI3

    International Nuclear Information System (INIS)

    Kawamura, Yukihiko; Mashiyama, Hiroyuki; Hasebe, Katsuhiko

    2002-01-01

    The cubic-tetragonal phase transition of CH 3 NH 3 PbI 3 was investigated by single crystal X-ray diffractometry. The crystal structure was refined at five temperatures in the tetragonal phase. The PbI 6 octahedron rotates around the c-axis alternatively to construct the SrTiO 3 -type tetragonal structure. A methylammonium ion is partially ordered; 24 disordered states in the cubic phase are reduced to 8. With decreasing temperature, the rotation angle of the octahedron increases monotonically, which indicates it is an order parameter of the cubic-tetragonal transition. (author)

  11. Experimental study of stress-induced localized transformation plastic zones in tetragonal zirconia polycrystalline ceramics

    International Nuclear Information System (INIS)

    Sun, Q.; Zhao, Z.; Chen, W.; Qing, X.; Xu, X.; Dai, F.

    1994-01-01

    Stress-induced martensitic transformation plastic zones in ceria-stabilized tetragonal zirconia polycrystalline ceramics (Ce-TZP), under loading conditions of uniaxial tension, compression, and three-point bending, are studied by experiments. The transformed monoclinic phase volume fraction distribution and the corresponding plastic strain distribution and the surface morphology (surface uplift) are measured by means of moire interferometry, Raman microprobe spectroscopy, and the surface measurement system. The experimental results from the above three kinds of specimens and methods consistently show that the stress-induced transformation at room temperature of the above specimen is not uniform within the transformation zone and that the plastic deformation is concentrated in some narrow band; i.e., macroscopic plastic flow localization proceeds during the initial stage of plastic deformation. Flow localization phenomena are all observed in uniaxial tension, compression, and three-point bending specimens. Some implications of the flow localization to the constitutive modeling and toughening of transforming thermoelastic polycrystalline ceramics are explored

  12. Excimer laser assisted re-oxidation of BaTiO3 thin films on Ni metal foils

    International Nuclear Information System (INIS)

    Bharadwaja, S. S. N.; Ko, S. W.; Qu, W.; Clark, T.; Rajashekhar, A.; Motyka, M.; Podraza, N.; Randall, C. A.; Trolier-McKinstry, S.

    2016-01-01

    Excimer laser assisted re-oxidation for reduced, crystallized BaTiO 3 thin films on Ni-foils was investigated. It was found that the BaTiO 3 can be re-oxidized at an oxygen partial pressure of ∼50 mTorr and substrate temperature of 350 °C without forming a NiO x interface layer between the film and base metal foil. The dielectric permittivity of re-oxidized films was >1000 with loss tangent values <2% at 100 Hz, 30 mV rms excitation signal. Electron Energy Loss Spectroscopy indicated that BaTiO 3 thin films can be re-oxidized to an oxygen stoichiometry close to ∼3 (e.g., stoichiometric). High resolution cross sectional transmission electron microscopy showed no evidence of NiO x formation between the BaTiO 3 and the Ni foil upon excimer laser re-oxidation. Spectroscopic ellipsometry studies on laser re-oxidized [001] C and [111] C BaTiO 3 single crystals indicate that the re-oxidation of BaTiO 3 single crystals is augmented by photo-excitation of the ozone, as well as laser pulse induced temperature and local stress gradients

  13. The effect of thermal cycling on tetragonal to monoclinic transformation in ZrO2(2%Y2O3) ceramic studied by high temperature X-ray diffraction

    International Nuclear Information System (INIS)

    Zhu, W.Z.; Lei, T.C.; Zhou, Y.

    1993-01-01

    It has been established that brittleness and reliability of ceramics can be improved by a stress-triggered tetragonal (T) to monoclinic (M) transformation in zirconia termed transformation toughening. The T → M transformation is not only influenced by such intrinsic factors as the variety and amount of stabilizers, grain size and morphology of T phase, but can be affected by the cooling rate as well. A previous study by Tsubadin, using a dilation experiment to determine the effect of thermal cycling on the T → M transformation in partially stabilized zirconia suggested that sintering temperature determined the role of thermal cycling, while the underlying cause still remains ambiguous. The intent of the present paper is to reinvestigate the effect of thermal cycling on the T → M transition in a hot pressed ZrO 2 (2%y 2 O 3 ) ceramic, using a high temperature x-ray diffractometer, and rationalize the experimental results from the viewpoint of thermodynamics

  14. Electro-caloric effect in lead-free Sn doped BaTiO3 ceramics at room temperature and low applied fields

    International Nuclear Information System (INIS)

    Upadhyay, Sanjay Kumar; Reddy, V. Raghavendra; Bag, Pallab; Rawat, R.; Gupta, S. M.; Gupta, Ajay

    2014-01-01

    Structural, dielectric, ferroelectric (FE), 119 Sn Mössbauer, and specific heat measurements of polycrystalline BaTi 1–x Sn x O 3 (x = 0% to 15%) ceramics are reported. Phase purity and homogeneous phase formation with Sn doping is confirmed from x-ray diffraction and 119 Sn Mössbauer measurements. With Sn doping, the microstructure is found to change significantly. Better ferroelectric properties at room temperature, i.e., increased remnant polarization (38% more) and very low field switchability (225% less) are observed for x = 5% sample as compared to other samples and the results are explained in terms of grain size effects. With Sn doping, merging of all the phase transitions into a single one is observed for x ≥ 10% and for x = 5%, the tetragonal to orthorhombic transition temperature is found close to room temperature. As a consequence better electro-caloric effects are observed for x = 5% sample and therefore is expected to satisfy the requirements for non-toxic, low energy (field) and room temperature based applications.

  15. Residual stress relief due to fatigue in tetragonal lead zirconate titanate ceramics

    International Nuclear Information System (INIS)

    Hall, D. A.; Mori, T.; Comyn, T. P.; Ringgaard, E.; Wright, J. P.

    2013-01-01

    High energy synchrotron XRD was employed to determine the lattice strain ε{111}and diffraction peak intensity ratio R{200}in tetragonal PZT ceramics, both in the virgin poled state and after a bipolar fatigue experiment. It was shown that the occurrence of microstructural damage during fatigue was accompanied by a reduction in the gradient of the ε{111}–cos 2 ψ plot, indicating a reduction in the level of residual stress due to poling. In contrast, the fraction of oriented 90° ferroelectric domains, quantified in terms of R{200}, was not affected significantly by fatigue. The change in residual stress due to fatigue is interpreted in terms of a change in the average elastic stiffness of the polycrystalline matrix due to the presence of inter-granular microcracks

  16. Residual stress relief due to fatigue in tetragonal lead zirconate titanate ceramics

    Science.gov (United States)

    Hall, D. A.; Mori, T.; Comyn, T. P.; Ringgaard, E.; Wright, J. P.

    2013-07-01

    High energy synchrotron XRD was employed to determine the lattice strain ɛ{111} and diffraction peak intensity ratio R{200} in tetragonal PZT ceramics, both in the virgin poled state and after a bipolar fatigue experiment. It was shown that the occurrence of microstructural damage during fatigue was accompanied by a reduction in the gradient of the ɛ{111}-cos2 ψ plot, indicating a reduction in the level of residual stress due to poling. In contrast, the fraction of oriented 90° ferroelectric domains, quantified in terms of R{200}, was not affected significantly by fatigue. The change in residual stress due to fatigue is interpreted in terms of a change in the average elastic stiffness of the polycrystalline matrix due to the presence of inter-granular microcracks.

  17. Raman spectra, photoluminescence, magnetism and magnetoelectric coupling in pure and Fe doped BaTiO3 nanostructures

    International Nuclear Information System (INIS)

    Verma, Kuldeep Chand; Gupta, Vinay; Kaur, Jaspreet; Kotnala, R.K.

    2013-01-01

    Highlights: •Multiferroic nanostructures by surfactant free hydrothermal method. •Stoichiometric effect on nanostructures. •Raman spectroscopy and Photoluminescence. •Transmission electron microscopy. •Magnetoelectric coupling. -- Abstract: Structural, microstructural, Raman spectroscopy, photoluminescence, saturation magnetization and magnetoelectric (ME) measurement of BaTiO 3 (BFT0) and BaFe 0.01 Ti 0.99 O 3 (BFT1) nanostructures have been studied. BFT0 and BFT1 were prepared by a hydrothermal method of processing temperature 180 °C/48 h. The X-ray diffraction pattern shows the coexistence of cubic/tetragonal and hexagonal phases for BFT0 and cubic/tetragonal for BFT1. The Raman spectra confirm the coexistence of tetragonal and hexagonal phases in BFT0 and cubic in BFT1. Transmission electron microscopy images show nanorods of hexagonal shaped faces for BFT0 and cubic shaped nanowires for BFT1. The resulting mechanism of the formation of these nanostructures is discussed. The experimental and theoretical results by photoluminescence are related to the degree of disorder existing in both BFT0 and BFT1 and suggest the presence of localized states existing inside of the band gap which are directly affected for degree of order–disorder. A strong ferromagnetism in BFT1 and diamagnetism in BFT0 is observed by magnetic hysteresis. As BFT1 is ferromagnetic, the value of linear coefficient, α called Magnetoelectric (ME) coefficient is calculated as ∼16 mV/Oe cm at a fixed frequency of 850 Hz. This ME coefficient α corresponds to induction of polarization by a magnetic field or of magnetization by an electric field. The observed optimum dc bias field at which the maximum ME coupling occurs is ∼750 Oe

  18. Dynamic Displacement Disorder of Cubic BaTiO3

    Science.gov (United States)

    Paściak, M.; Welberry, T. R.; Kulda, J.; Leoni, S.; Hlinka, J.

    2018-04-01

    The three-dimensional distribution of the x-ray diffuse scattering intensity of BaTiO3 has been recorded in a synchrotron experiment and simultaneously computed using molecular dynamics simulations of a shell model. Together, these have allowed the details of the disorder in paraelectric BaTiO3 to be clarified. The narrow sheets of diffuse scattering, related to the famous anisotropic longitudinal correlations of Ti ions, are shown to be caused by the overdamped anharmonic soft phonon branch. This finding demonstrates that the occurrence of narrow sheets of diffuse scattering agrees with a displacive picture of the cubic phase of this textbook ferroelectric material. The presented methodology allows one to go beyond the harmonic approximation in the analysis of phonons and phonon-related scattering.

  19. Texturation of lead-free BaTiO3-based piezoelectric ceramics

    OpenAIRE

    Ngueteu-Kamlo , A; Levassort , F; Pham Thi , M; Marchet , Pascal

    2014-01-01

    International audience; Nowadays, piezoelectric ceramics are integrated in a wide range of devices, in particular in ultrasonic applications (underwater sonar systems, medical imaging, non-destructive testing…). Most of them use Pb(Zr,Ti)O3 (PZT). However, due to health care and environmental problems, lead content must be reduced in such applications [1]. Recent reviews demonstrated that few lead-free materials families can be considered: the alkaline-niobates (K0.5Na0.5NbO3), the alkaline-b...

  20. Syntheses of nanocrystalline BaTiO3 and their optical properties

    Science.gov (United States)

    Yu, J.; Chu, J.; Zhang, M.

    Stoichiometric and titanium-excess nanocrystalline barium titanates were synthesized using a hydrothermal process at various hydrothermal temperatures and with further heat treatment at 500 °C and 900 °C. Owing to the different process conditions, the excess titanium exists in different states and configurations within the nanocrystalline BaTiO3 matrix; this was demonstrated by X-ray diffraction, Raman scattering, and photoluminescence. In these nanocrystalline BaTiO3, the 590, 571, 543 and 694 nm light emission bands were observed; mechanisms leading to such emissions were also discussed.

  1. Nucleation control and inhibition of BaTiO3 films using hydrothermal-electrochemical method

    International Nuclear Information System (INIS)

    Escobar, Ivan; Silva, Carmen; Silva, Eric; Vargas, Tomas; Fuenzalida, Victor

    1999-01-01

    The microstructure of BaTiO 3 films on titanium by the hydrothermal-electrochemical method was investigated using a three electrode high pressure electrochemical cell in a 0.2 M Ba(OH) 2 electrolyte at 150 0 C. The spontaneous initial linked to pure hydrothermal BaTiO 3 formation can be inhibited by cathodically protecting titanium electrode since its immersion in the electrolyte. The application of initial nucleation pulses of varying the cathodic potentials affected the grain size of the deposit. It is suggested that the formation of a titanium oxide layers is a necessary step previous to the nucleation of BaTiO 3

  2. Ceramic Composites of 3Y-TZP Doped with CuO: Processing, Microstructure and Tribology

    NARCIS (Netherlands)

    Ran, S.

    2006-01-01

    The work described in this thesis is about processing, microstructure and tribology of CuO doped 3Y-TZP (3 mol% yttria stabilised tetragonal zirconia polycrystals) composite ceramics. This group of materials has shown attractive properties such as superplastic behaviour at elevated temperature and a

  3. Spin-Coating and Characterization of Multiferroic MFe2O4 (M=Co, Ni) / BaTiO3 Bilayers

    Science.gov (United States)

    Quandt, Norman; Roth, Robert; Syrowatka, Frank; Steimecke, Matthias; Ebbinghaus, Stefan G.

    2016-01-01

    Bilayer films of MFe2O4 (M=Co, Ni) and BaTiO3 were prepared by spin coating of N,N-dimethylformamide/acetic acid solutions on platinum coated silicon wafers. Five coating steps were applied to get the desired thickness of 150 nm for both the ferrite and perovskite layer. XRD, IR and Raman spectroscopy revealed the formation of phase-pure ferrite spinels and BaTiO3. Smooth surfaces with roughnesses in the order of 3 to 5 nm were found in AFM investigations. Saturation magnetization of 347 emu cm-3 for the CoFe2O4/BaTiO3 and 188 emu cm-3 for the NiFe2O4/BaTiO3 bilayer, respectively were found. For the CoFe2O4/BaTiO3 bilayer a strong magnetic anisotropy was observed with coercivity fields of 5.1 kOe and 3.3 kOe (applied magnetic field perpendicular and parallel to film surface), while for the NiFe2O4/BaTiO3 bilayer this effect is less pronounced. Saturated polarization hysteresis loops prove the presence of ferroelectricity in both systems.

  4. Study of radiation damage in BaTiO3, using Molecular-dynamics simulations

    International Nuclear Information System (INIS)

    Gonzalez, E.; Abreu, Y.; Cruz, C. M.; Pinnera, I.; Leyva, A.

    2015-01-01

    Molecular-dynamics (MD) simulations were used to calculate atomic displacement probability curves along main crystallographic directions in BaTiO 3 perovskite. A primary knock-on atom (PKA) with a energy range between 10 to 300 eV in principal crystallographic directions at 300 K was introduced. For each sublattice, the simulation was repeated from different initial conditions to estimate the variation in the defect formation process. The formation of Frenkel pairs vary considerably with crystallographic direction and sublattice. Major quantity oxygen defects were found for all the simulated crystallographic directions. Threshold displacement energies are calculated for each atomic specie in the BaTiO 3 material. Also simulations with SRIM code, modeling + Mn implantation in a BaTiO 3 target, at 250 keV were made. (Author)

  5. Evolution from successive phase transitions to "morphotropic phase boundary" in BaTiO3-based ferroelectrics

    Science.gov (United States)

    Zhou, Chao; Ke, Xiaoqin; Yao, Yonggang; Yang, Sen; Ji, Yuanchao; Liu, Wenfeng; Yang, Yaodong; Zhang, Lixue; Hao, Yanshuang; Ren, Shuai; Zhang, Le; Ren, Xiaobing

    2018-04-01

    Obtaining superior physical properties for ferroic materials by manipulating the phase transitions is a key concern in solid state physics. Here, we investigated the dielectric permittivity, piezoelectric coefficient d33, storage modulus, and crystal symmetry of (1-x)Ba(Ti0.8Zr0.2)O3-x(Ba1-yCay)TiO3 (BZT-xBCyT) systems to demonstrate the gradual evolution process from successive phase transitions in BaTiO3 to the morphotropic phase boundary (MPB) regime in BZT-xBC0.3T. Furthermore, we analysed with a Landau-type theoretical model to show that the high field-sensitive response (dielectric permittivity) originates from a small polarization anisotropy and low energy barrier at the quadruple point. Together, the intermediate orthorhombic phase regime and the tetragonal-orthorhombic and orthorhombic-rhombohedral phase boundaries constitute the MPB. Our work not only reconciles the arguments regarding whether the structural state around the MPB corresponds to a single-phase regime or a multiple-phase-coexistence regime but also suggests an effective method to design high-performance functional ferroic materials by tailoring the successive phase transitions.

  6. Characterization and dielectric properties of BaTiO3 prepared from Ba(NO3)2-TiO2 mixture

    International Nuclear Information System (INIS)

    Othman, K.I.; Hassan, A.A.; Ali, M.E.; Abdelal, O.A.; Salah El Dien, F.E.; El-Raghy, S.M.; Abdel-Karim, R.

    2012-01-01

    BaTiO 3 powder was prepared through a solid-state reaction between the Ba(NO 3 ) 2 and TiO 2 . The thermal analysis and XRD techniques were used to study its formation. A single phase BaTiO 3 was formed after calcination at 600 degree C for 6 hrs. The dielectric properties of the sintered BaTiO 3 were determined in the temperature range from room temperature to 20 degree C at a frequency ranging from 500 Hz to 100 khz. The relative permittivity and the dielectric loss of the sintered pellets at 1 khz, measured at room temperature,were 1805 and 0.419 respectively.

  7. Influence of Impurities on the Luminescence of Er3+ Doped BaTiO3 Nanophosphors

    Directory of Open Access Journals (Sweden)

    G. D. Webler

    2014-01-01

    Full Text Available The influence of the presence of barium carbonate (BaCO3 phase on the luminescence properties of barium titanate nanocrystals (BaTiO3 powders was investigated. Structural and optical characterizations of erbium (Er3+ doped BaTiO3 synthesized by the sol-emulsion-gel were performed. Using Fourier transform infrared spectroscopy and X-ray powder diffraction, we identified the presence of impurities related to BaCO3 and quantified its fraction. It was observed that the presence of BaCO3 phase, even at low levels, depletes significantly the infrared-to-visible upconverted luminescence efficiency of the produced nanopowders.

  8. Crystallization and dielectric properties of PbTiO3 based glass ceramics

    Science.gov (United States)

    Shankar, J.; Rani, G. Neeraja; Deshpande, V. K.

    2018-04-01

    Glass samples with composition (50 - X) PbO - (25 + X) TiO2 - 25 B2O3 (where X = 0, 5, 10 and 12.5 mol %) were prepared using conventional quenching technique. These glass samples were converted to glass ceramics by following two stage heat treatment schedule. The XRD results in the glass ceramics revealed the formation of tetragonal lead titanate as a major crystalline phase. The SEM results show rounded crystallite of lead titanate. The ferroelectric nature of all the glass ceramic samples is confirmed by P - E hysteresis measurements. The extended heat treatment of glass ceramic samples at 593K for 10 h exhibited saturated hysteresis loops with higher values of remnant polarization.

  9. The Oxidation States of Cooper in Sb, Cu Doped Ba.sub.0.9./sub.Sr.sub.0.1./sub. TiO.sub.3./sub. Ceramics

    Czech Academy of Sciences Publication Activity Database

    Medvecký, L.; Briančin, J.; Trpcevská, J.; Pelikan, P.; Bastl, Zdeněk

    2001-01-01

    Roč. 20, - (2001), s. 419-422 ISSN 0261-8028 Institutional research plan: CEZ:AV0Z4040901 Keywords : BaTiO3 ceramics * conductivity * trap centers Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 0.489, year: 2001

  10. Epitaxial c-axis oriented BaTiO3 thin films on SrTiO3-buffered Si(001) by atomic layer deposition

    International Nuclear Information System (INIS)

    Ngo, Thong Q.; McDaniel, Martin D.; Ekerdt, John G.; Posadas, Agham B.; Demkov, Alexander A.; Hu, Chengqing; Yu, Edward T.; Bruley, John

    2014-01-01

    Atomic layer deposition (ALD) of epitaxial c-axis oriented BaTiO 3 (BTO) on Si(001) using a thin (1.6 nm) buffer layer of SrTiO 3 (STO) grown by molecular beam epitaxy is reported. The ALD growth of crystalline BTO films at 225  °C used barium bis(triisopropylcyclopentadienyl), titanium tetraisopropoxide, and water as co-reactants. X-ray diffraction (XRD) reveals a high degree of crystallinity and c-axis orientation of as-deposited BTO films. Crystallinity is improved after vacuum annealing at 600  °C. Two-dimensional XRD confirms the tetragonal structure and orientation of 7–20-nm thick films. The effect of the annealing process on the BTO structure is discussed. A clean STO/Si interface is found using in-situ X-ray photoelectron spectroscopy and confirmed by cross-sectional scanning transmission electron microscopy. The capacitance-voltage characteristics of 7–20 nm-thick BTO films are examined and show an effective dielectric constant of ∼660 for the heterostructure

  11. Crystal Growth and Characterization of (Bi0.5Na0.5)TiO3-BaTiO3 Single Crystals Obtained by a Top-Seeded Solution Growth Method under High-Pressure Oxygen Atmosphere

    Science.gov (United States)

    Onozuka, Hiroaki; Kitanaka, Yuuki; Noguchi, Yuji; Miyayama, Masaru

    2011-09-01

    A single crystal of ferroelectric 0.88(Bi,Na)TiO3-0.12BaTiO3 (BNT-BT) solid solution with tetragonal P4mm structure was grown by a top-seeded solution growth (TSSG) method at a high oxygen pressure (PO2 ) of 0.9 MPa. The crystals exhibited a large remanent polarization (Pr) of 54 µC/cm2, which leads to a spontaneous polarization estimated to be 54 µC/cm2. The large Pr compared with that of crystals grown at PO2 = 0.1 MPa is suggested to originate from a low oxygen vacancy concentration. The high-PO2 TSSG method is demonstrated to be effective for obtaining large-sized, high-quality BNT-BT crystals.

  12. Deposition barium titanate (BaTiO3) doped lanthanum with chemical solution deposition

    International Nuclear Information System (INIS)

    Iriani, Y.; Nurhadi, N.; Jamaludin, A.

    2016-01-01

    Deposition of Barium Titanate (BaTiO 3 ) thin films used Chemical Solution Deposition (CSD) method and prepared with spin coater. BaTiO 3 is doped with lanthanum, 1%, 2%, and 3%. The thermal process use annealing temperature 900°C and holding time for 3 hours. The result of characterization with x-ray diffraction (XRD) equipment show that the addition of La 3+ doped on Barium Titanate caused the change of angle diffraction.The result of refine with GSAS software shows that lanthanum have been included in the structure of BaTiO 3 . Increasing mol dopant La 3+ cause lattice parameter and crystal volume become smaller. Characterization result using Scanning Electron Microscopy (SEM) equipment show that grain size (grain size) become smaller with increasing mole dopant (x) La 3+ . The result of characterization using Sawyer Tower methods show that all the samples (Barium Titanante and Barium Titanate doped lanthanum) are ferroelectric material. Increasing of mole dopant La 3+ cause smaller coercive field and remanent polarization increases. (paper)

  13. Highly piezoelectric BaTiO3 nanorod bundle arrays using epitaxially grown TiO2 nanomaterials.

    Science.gov (United States)

    Jang, Seon-Min; Yang, Su Chul

    2018-06-08

    Low-dimensional piezoelectric nanostructures such as nanoparticles, nanotubes, nanowires, nanoribbons and nanosheets have been developed for potential applications as energy harvesters, tunable sensors, functional transducers and low-power actuators. In this study, lead-free BaTiO 3 nanorod bundle arrays (NBA) with highly piezoelectric properties were successfully synthesized on fluorine-doped tin oxide (FTO) substrate via a two-step process consisting of TiO 2 epitaxial growth and BaTiO 3 conversion. Through the TiO 2 epitaxial growth on FTO substrate, (001) oriented TiO 2 nanostructures formed vertically-aligned NBA with a bundle diameter of 80 nm and an aspect ratio of six. In particular, chemical etching of the TiO 2 NBA was conducted to enlarge the surface area for effective Ba 2+ ion diffusion during the perovskite conversion process from TiO 2 to BaTiO 3 . The final structure of perovskite BaTiO 3 NBA was found to exhibit a feasible piezoelectric response of 3.56 nm with a clear phase change of 180° from the single BaTiO 3 bundle, by point piezoelectric forced microscopy (PFM) analysis. Consequently, highly piezoelectric NBA could be a promising nanostructure for various nanoscale electronic devices.

  14. Highly piezoelectric BaTiO3 nanorod bundle arrays using epitaxially grown TiO2 nanomaterials

    Science.gov (United States)

    Jang, Seon-Min; Yang, Su Chul

    2018-06-01

    Low-dimensional piezoelectric nanostructures such as nanoparticles, nanotubes, nanowires, nanoribbons and nanosheets have been developed for potential applications as energy harvesters, tunable sensors, functional transducers and low-power actuators. In this study, lead-free BaTiO 3 nanorod bundle arrays (NBA) with highly piezoelectric properties were successfully synthesized on fluorine-doped tin oxide (FTO) substrate via a two-step process consisting of TiO2 epitaxial growth and BaTiO3 conversion. Through the TiO2 epitaxial growth on FTO substrate, (001) oriented TiO2 nanostructures formed vertically-aligned NBA with a bundle diameter of 80 nm and an aspect ratio of six. In particular, chemical etching of the TiO2 NBA was conducted to enlarge the surface area for effective Ba2+ ion diffusion during the perovskite conversion process from TiO2 to BaTiO3. The final structure of perovskite BaTiO3 NBA was found to exhibit a feasible piezoelectric response of 3.56 nm with a clear phase change of 180° from the single BaTiO3 bundle, by point piezoelectric forced microscopy (PFM) analysis. Consequently, highly piezoelectric NBA could be a promising nanostructure for various nanoscale electronic devices.

  15. Dielectric behaviour of (Ba0.77Ca0.23(Ti0.98Dy0.02O3 ceramics

    Directory of Open Access Journals (Sweden)

    Abdul Moquim

    2015-06-01

    Full Text Available In this study, BaTiO3 is modified with Ca2+ and in addition doped with Dy3+ at the B site lattice. The main idea is to search for new lead-free ferroelectric material and improve their properties. For this purpose, the barium calcium titanate (BCT as a host and the rare earth element Dy3+ as an activator were used to fabricate a multifunctional material. The obtained ceramics was found to be homogeneous, dense and a single phase material with no evidence of secondary phases. The dielectric study showed that TC increases with the addition of dopants and the obtained ceramics behaves like a relaxor ferroelectric. Some important structural parameters and dielectric properties of dysprosium modified barium (calcium titanate ceramics are presented.

  16. Thickness dependent charge transport in ferroelectric BaTiO3 heterojunctions

    Science.gov (United States)

    Singh, Pooja; Rout, P. K.; Singh, Manju; Rakshit, R. K.; Dogra, Anjana

    2015-09-01

    We have investigated the effect of ferroelectric barium titanate (BaTiO3) film thickness on the charge transport mechanism in pulsed laser deposited epitaxial metal-ferroelectric semiconductor junctions. The current (I)-voltage (V) measurements across the junctions comprising of 20-500 nm thick BaTiO3 and conducting bottom electrode (Nb: SrTiO3 substrate or La2/3Ca1/3MnO3 buffer layer) demonstrate the space charge limited conduction. Further analysis indicates a reduction in the ratio of free to trapped carriers with increasing thickness in spite of decreasing trap density. Such behaviour arises the deepening of the shallow trap levels (I-V curves implies a bipolar resistive switching behaviour, which can be explained in terms of charge trapping and de-trapping process.

  17. Base-Metal Electrode-Multilayer Ceramic Capacitors: Past, Present and Future Perspectives

    Science.gov (United States)

    Kishi, Hiroshi; Mizuno, Youichi; Chazono, Hirokazu

    2003-01-01

    Multilayer ceramic capacitor (MLCC) production and sales figures are the highest among fine-ceramic products developed in the past 30 years. The total worldwide production and sales reached 550 billion pieces and 6 billion dollars, respectively in 2000. In the course of progress, the development of base-metal electrode (BME) technology played an important role in expanding the application area. In this review, the recent progress in MLCCs with BME nickel (Ni) electrodes is reviewed from the viewpoint of nonreducible dielectric materials. Using intermediate-ionic-size rare-earth ion (Dy2O3, Ho2O3, Er2O3, Y2O3) doped BaTiO3 (ABO3)-based dielectrics, highly reliable Ni-MLCCs with a very thin layer below 2 μm in thickness have been developed. The effect of site occupancy of rare-earth ions in BaTiO3 on the electrical properties and microstructure of nonreducible dielectrics is studied systematically. It appears that intermediate-ionic-size rare-earth ions occupy both A- and B-sites in the BaTiO3 lattice and effectively control the donor/acceptor dopant ratio and microstructural evolution. The relationship between the electrical properties and the microstructure of Ni-MLCCs is also presented.

  18. Lateral electric-field control of giant magnetoresistance in Co/Cu/Fe/BaTiO3 multiferroic heterostructure

    International Nuclear Information System (INIS)

    Savitha Pillai, S.; Kojima, H.; Itoh, M.; Taniyama, T.

    2015-01-01

    We report lateral electric-field-driven sizable changes in the magnetoresistance of Co/Cu/Fe tri-layered wires on BaTiO 3 single crystal. While the observed change is marginal in the tetragonal phase of BaTiO 3 , it reaches over 40% in the orthorhombic and rhombohedral phases with an electric field of 66 kV/cm. We attribute it to possible electric-field-induced variations of the spin-dependent electronic structures, i.e., spin polarization, of the Fe via interfacial strain transfer from BaTiO 3 . The contrasting results for the different phases of BaTiO 3 are discussed, associated with the distinct aspects of the ferroelectric polarization switching processes in each phase

  19. Lateral electric-field control of giant magnetoresistance in Co/Cu/Fe/BaTiO3 multiferroic heterostructure

    Science.gov (United States)

    Savitha Pillai, S.; Kojima, H.; Itoh, M.; Taniyama, T.

    2015-08-01

    We report lateral electric-field-driven sizable changes in the magnetoresistance of Co/Cu/Fe tri-layered wires on BaTiO3 single crystal. While the observed change is marginal in the tetragonal phase of BaTiO3, it reaches over 40% in the orthorhombic and rhombohedral phases with an electric field of 66 kV/cm. We attribute it to possible electric-field-induced variations of the spin-dependent electronic structures, i.e., spin polarization, of the Fe via interfacial strain transfer from BaTiO3. The contrasting results for the different phases of BaTiO3 are discussed, associated with the distinct aspects of the ferroelectric polarization switching processes in each phase.

  20. Influence of rare-earth additives (La, Sm and Dy on the microstructure and dielectric properties of doped BaTiO3 ceramics

    Directory of Open Access Journals (Sweden)

    Paunović Vesna

    2010-01-01

    Full Text Available A series of La/Mn, Sm/Mn and Dy/Mn codoped BaTiO3 samples were prepared by the conventional solid state procedure with dopant concentrations ranging from 0.1 up to 2.0 at%. The specimens were sintered at 1320°C and 1350°C in an air atmosphere for two hours. The low doped samples demonstrated a mainly uniform and homogeneous microstructure with average grain sizes ranging from 0.3 μm to 5.0 μm. The appearance of secondary abnormal grains in the fine grain matrix and core-shell structure were observed in highly doped La/BaTiO3 and Dy/BaTiO3 sintered at 1350°C. The low doped samples, sintered at 1350°C, display a high value of dielectric permittivity at room temperature, 6800 for Sm/BaTiO3, 5900 for Dy/BaTiO3 and 3100 for La/BaTiO3. A nearly flat permittivity-response was obtained in specimens with 2.0 at% additive content. Using a modified Curie-Weiss law the Curie-like constant C⁄ and a critical exponent γ were calculated. The obtained values of γ pointed out the diffuse phase transformation in heavily doped BaTiO3 samples.

  1. Synthesis of BaTiO3 nanoparticles from TiO2-coated BaCO3 particles derived using a wet-chemical method

    Directory of Open Access Journals (Sweden)

    Yuuki Mochizuki

    2014-03-01

    Full Text Available BaCO3 particles coated with amorphous TiO2 precursor are prepared by a wet chemical method to produce BaTiO3 nanoparticles at low temperatures. Subsequently, we investigate the formation behavior of BaTiO3 particles and the particle growth behavior when the precursor is subjected to heat treatment. The state of the amorphous TiO2 coating on the surface of BaCO3 particles depends on the concentration of NH4HCO3, and the optimum concentration is found to be in the range 0.5–1.0 M. Thermogravimetric curves of the BaCO3 particles coated with the TiO2 precursor, prepared from BaCO3 particles of various sizes, show BaTiO3 formation occurring mainly at 550–650 °C in the case of fine BaCO3 particles. However, as evidenced from the curves, the temperature of formation of BaTiO3 shifts to higher values with an increase in the size of the BaCO3 particles. The average particle size of single phase BaTiO3 at heat-treatment temperature of 650–900 °C is observed to be in the range 60–250 nm.

  2. Nanocomposites of ferroelectric polymers with surface-hydroxylated BaTiO 3 nanoparticles for energy storage applications

    KAUST Repository

    Almadhoun, Mahmoud Nassar Mahmoud

    2012-01-01

    A facile surface hydroxylation treatment using hydrogen peroxide to modify the surface of BaTiO 3 nanofillers dispersed in a ferroelectric copolymer host has been investigated. We demonstrate that the surface functionalization of the BaTiO 3 nanofillers (<100 nm) with hydroxyl groups results in as much as two orders of magnitude reduction in the leakage current of nanocomposite thin-film capacitors. This reduction is observed concurrently with the enhancement of the effective permittivity and breakdown strength of the thin-film nanocomposites. Surface modified BaTiO 3 particles display better dispersion within the polymer matrix, resulting in enhanced relative permittivity and reduced dielectric loss. The dielectric behavior of the nanocomposite films containing up to 30 vol.% BaTiO 3 agreed well with the Bruggeman model. These results demonstrate the potential of facile surface hydroxylation of nanoparticles towards the fabrication of higher energy-density nanocomposites. © 2012 The Royal Society of Chemistry.

  3. Effect of combined external uniaxial stress and dc bias on the dielectric property of BaTiO3-based dielectrics in multilayer ceramic capacitor: thermodynamics and experiments

    International Nuclear Information System (INIS)

    Yang Gang; Yue Zhenxing; Sun Tieyu; Gou Huanlin; Li Longtu

    2008-01-01

    The dielectric properties of (Nb, Y)-doped BaTiO 3 in a multilayer ceramic capacitor (MLCC) under combined external uniaxial compressive stress and dc bias field were investigated at room temperature by using a modified Ginsburg-Landau-Devonshire thermodynamic theory and the dielectric measurement. It is found that although dc bias decreases the dielectric properties dominantly, the influence of the external uniaixial compressive stress should not be neglected. When applied along a direction perpendicular to the internal electrode layer in the MLCC, the external uniaixal compressive stress will strengthen the negative effect of dc bias. In contrast, the external uniaxial compressive stress along a direction parallel to the internal electrode layer in the MLCC will increase the dielectric permittivity under dc bias field, i.e. improve the ε-V response of the MLCC. Furthermore, although there is a difference between the calculated permittivity and the measured permittivity, the effects of the combined external uniaxial compressive stress and dc bias field on the dielectric permittivity described through two approaches are in good agreement

  4. Flow method for rapid production of Batio3 nanoparticles in supercritical water

    International Nuclear Information System (INIS)

    Atashfaraz, M.; Shariati-Niassar, M.; Ohara, Satoshi; Takami, S.; Umetsu, M.; Naka, T.; Adschiri, T.

    2006-01-01

    Fine BaTiO 3 nanoparticles were obtained by hydrothermal synthesis under supercritical conditions with batch and flow type experimental methods. Mixture of barium hydroxide and titanium oxide starting solution was treated in the supercritical wafer at 400 d eg C and 30 MPa. The size of nanoparticles synthesized in the flow type experiment was smaller than that in the batch type. Rapid heating in a flow, reactor is effective to synthesize smaller size and narrower particle size distribution for the BaTiO 3 , nanoparticles. The mechanism for this result was discussed based on the solubility of titanium oxide

  5. Evolución Microestructural de Materiales Cerámicos de BaTiO3 Dopados con Antimonio

    Directory of Open Access Journals (Sweden)

    Villegas, M.

    1999-10-01

    Full Text Available Ceramic materials based on BaTiO3 modified with small amounts of antimony show interesting electric properties which make them valuable for electronic industry. These properties depend on the microestructure of the material, which is controlled by both the dopant concentration and the doping process. The aim of the present work is to study the microstructure development of Sb-doped BaTiO3 materials for concentrations ranging from 0.05 to 0.6 mol%. Doping was carried out following two different methods, the traditional mixing of oxides and surface doping starting from Sb(O(CH3CH33. Materials sintered between 1300-1400ºC show quite different microstructure. For surface doped materials, a Sb2O3 concentration of 0.05 mol % leads to well densified matrials with homogeneous fine-grained microstructure. On the other hand, the traditional oxide doped materials show exaggerated grain growth.Los materiales cerámicos basados en titanato de bario con pequeñas cantidades de antimonio, exhiben interesantes propiedades que hacen posible su aplicación en la fabricación de dispositivos electrónicos. Estas propiedades dependen de la microestructura final del material, que está a su vez condicionada por la concentración de dopante y la vía utilizada para su incorporación. En este trabajo se estudia la evolución microestructural de materiales de BaTiO3 dopados con Sb en concentraciones entre 0.05 y 0.60 % mol. El dopado se ha realizado por la vía clásica a partir de Sb2O3 y mediante el proceso de dopado en superficie a partir de Sb(O(CH3CH33. Los materiales sinterizados en el intervalo de temperaturas comprendido entre 1300 y 1400ºC, muestran una microestructura bien diferenciada. Para los materiales dopados en superficie, una concentración equivalente de 0.05 % mol de Sb2O3 permite obtener materiales con elevada densidad y microestructura homogénea con tamaño de grano controlado. En el caso del material dopado por la vía clásica se observa

  6. Lattice distortion under an electric field in BaTiO3 piezoelectric single crystal

    International Nuclear Information System (INIS)

    Tazaki, Ryoko; Fu Desheng; Daimon, Masahiro; Koshihara, Shin-ya; Itoh, Mitsuru

    2009-01-01

    Lattice distortions under an electric field in a mono-domain of BaTiO 3 ferroelectric crystal have been detected with synchrotron x-ray radiation. The variation of the lattice constant with an electric field observed with high angle diffraction shows a linear response nature of the piezoelectric effect. When an electric field is applied along the spontaneous polarization direction, the c-axis of the lattice elongates and the a-axis of the lattice shrinks at a rate of d 33 = 149 ± 54 pm V -1 and d 31 = -82 ± 61 pm V -1 ; these represent the longitudinal and transverse piezoelectric coefficients of BaTiO 3 crystal, respectively. These results give an insight into the intrinsic piezoelectric response on the lattice scale in BaTiO 3 that has been widely used to explore high performance lead-free piezoelectric alloys.

  7. Band-offsets at BaTiO3/Cu2O heterojunction and enhanced photoelectrochemical response: theory and experiment(Conference Presentation)

    Science.gov (United States)

    Sharma, Dipika; Satsangi, Vibha R.; Dass Kaura, Sahab; Shrivastav, Rohit; Waghmare, Umesh V.

    2016-10-01

    Band-offsets at BaTiO3/Cu2O heterojunction and enhanced photoelectrochemical response: theory and experiment Dipika Sharmaa, Vibha R. Satsangib, Rohit Shrivastava, Umesh V. Waghmarec, Sahab Dassa aDepartment of Chemistry, Dayalbagh Educational Institute, Agra-282 110 (India) bDepartment of Physics and Computer Sciences, Dayalbagh Educational Institute, Agra-282 110 (India) cTheoretical Sciences Unit, Jawaharlal Nehru Centre for Advanced Scientific Research, Jakkur, Bangalore-560 064 (India) * Phone: +91-9219695960. Fax: +91-562-2801226. E-mail: drsahabdas@gmail.com. Study on photoelectrochemical activity of pristine BaTiO3, Cu2O and BaTiO3/Cu2O heterojunction has been carried out using DFT based band offsets and charge carriers effective mass calculations and their experimental verification. The results of DFT calculations show that BaTiO3 and Cu2O have staggered type band alignment after the heterojunction formation and high mobility of electrons in Cu2O as compared to the electrons in BaTiO3. Staggered type band edges alignment and high mobility of electrons and holes improved the separation of photo-generated charge carriers in BaTiO3/Cu2O heterojunction. To validate the theoretical results experiments were carried out on pristine BaTiO3, Cu2O and BaTiO3/Cu2O heterojunction with varying thickness of Cu2O. All samples were characterized by X- Ray Diffractometer, SEM and UV-Vis spectrometry. Nanostructured thin films of pristine BaTiO3, Cu2O and BaTiO3/Cu2O heterojunction were used as photoelectrode in the photoelectrochemical cell for water splitting reaction. Maximum photocurrent density of 1.44 mA/cm2 at 0.90 V/SCE was exhibited by 442 nm thick BaTiO3/Cu2O heterojunction photoelectrode Increased photocurrent density and enhanced photoconversion efficiency, exhibited by the heterojunction may be attributed to improved conductivity and enhanced separation of the photogenerated carriers at the BaTiO3/Cu2O interface. The experimental results and first

  8. Characterization, dielectric and electrical behaviour of BaTiO3 ...

    Indian Academy of Sciences (India)

    Administrator

    of λ = 0⋅1542 nm, for crystal structure determination. Scherrer's equation and ... ion, releasing one molecule of propanol and one molecule of triethanolamine in .... The OH, CO2 and CO3 peaks were reduced in the sam- ple of BaTiO3 when ...

  9. Electrical and mechanical properties of 0.5Ba (Zr0.2Ti0.8)O3-0.5 (Ba0.7Ca0.3)TiO3 (BZT-BCT) lead free ferroelectric ceramics reinforced with Al2O3 nano-oxide

    International Nuclear Information System (INIS)

    Adhikari, Prativa; Mazumder, R.

    2014-01-01

    Piezoelectric ceramics are widely used as actuator, resonator, and spark igniter. Recently, much attention has been paid to prepare 0.5Ba (Zr 0.2 Ti 0.8 )O 3 -0.5 (Ba 0.7 Ca 0.3 )TiO 3 (BZT-BCT) piezoelectric ceramics because of its good dielectric, piezoelectric properties and environment friendly nature. However, piezoelectric ceramics based on BaTiO 3 suffer from low reliability and poor mechanical properties such as strength and toughness. For practical application improvement of the mechanical properties of BaTiO 3 -based ceramics is strongly required. A novel method has been used to improve the mechanical properties of structural ceramics by reinforcement of oxide (Al 2 O 3 , MgO, ZrO 2 and Stabilized-ZrO 2 ) or non-oxide (SiC) particles. It is well known that electrical properties of ferroelectric ceramics generally degrade with non-ferroelectric additives and decrease in sinterability usually encountered with refractory oxide additives. Use of nano-oxide additives may drastically reduce the amount of additive and electrical property may not degrade much. In this report we would show the electrical and mechanical properties of BZT-BCT with Al 2 O 3 nano oxide additive. Modified BZT-BCT nanocomposites were prepared by mixing and sintering of solid state synthesized Zr, Ca modified barium titanate powder and small amount (0.1-2.0 vol %) of nano-oxides, i.e. Al 2 O 3 . Effect of sintering temperature, time, particle size of the nano-oxide additives on electrical (dielectric constant, loss factor, Curie temperature, d 33 ) and mechanical (flexural strength, fracture toughness, hardness) properties were studied. We obtained ∼ 94% dense BZT-BCT reinforced with Al 2 O 3 nano-oxide at 1300℃ without degrading electrical properties (dielectric constant (4850), low dissipation factor (0.0242)) and superior mechanical properties (flexural strength - 60.3 MPa, Vickers hardness-750-800 MPa). (author)

  10. Temperature-dependent high energy-resolution EELS of ferroelectric and paraelectric BaTiO3 phases

    Science.gov (United States)

    Bugnet, Matthieu; Radtke, Guillaume; Woo, Steffi Y.; Zhu, Guo-zhen; Botton, Gianluigi A.

    2016-01-01

    Probing the ferroelectricity at the nanometer scale is of particular interest for a wide range of applications. In this Rapid Communication, the structural distortion of BaTiO3 (BTO) is studied in its ferroelectric (rhombohedral and tetragonal), and paraelectric phases from the O K near edge structures in electron energy loss spectroscopy. Modifications of the electronic structure are detected in the lowest energy fine structure (FS) of the O K edge in the ferroelectric phases, and are interpreted by core-hole valence-electron screening geometry. For the paraelectric phase, the lowest energy FS of the O K edge is comparable to the one obtained at room temperature, which is inconsistent with an expected cubic structure. The variations observed in the O K near edge structures, such as a broader and more asymmetric lowest energy FS at low temperature, suggest that the magnitude of the Ti+4 off-centering along increases in lower-temperature phases. These findings demonstrate the sensitivity of the O K near edge structures to the structural distortions of BTO polymorphs, and form a basis for further investigations on defective or strained BTO at the nanoscale.

  11. Electronic and Structural Properties of ABO3: Role of the B-O Coulomb Repulsions for Ferroelectricity.

    Science.gov (United States)

    Miura, Kaoru; Azuma, Masaki; Funakubo, Hiroshi

    2011-01-17

    We have investigated the role of the Ti-O Coulomb repulsions in the appearance of the ferroelectric state in BaTiO3 as well as the role of the Zn-O Coulomb repulsions in BiZn0.5Ti0.5O3, using a first-principles calculation with optimized structures. In tetragonal BaTiO3, it is found that the Coulomb repulsions between Ti 3s and 3p states and O 2s and 2p states have an important role for the appearance of Ti ion displacement. In BiZn0.5Ti0.5O3, on the other hand, the stronger Zn-O Coulomb repulsions, which are due to the 3s, 3p, and 3d (d10) states of the Zn ion, have more important role than the Ti-O Coulomb repulsions for the appearance of the tetragonal structure. Our suggestion is consistent with the other ferroelectric perovskite oxides ABO3 in the appearance of tetragonal structures as well as rhombohedral structures.

  12. Fabrication of BaTiO3/Ni composite particles and their electro-magneto responsive properties

    International Nuclear Information System (INIS)

    Lu, Yaping; Gao, Lingxiang; Wang, Lijuan; Xie, Zunyuan; Gao, Meixiang; Zhang, Weiqiang

    2017-01-01

    Graphical abstract: The spherical BaTiO 3 /Ni particles with excellent structure were made by one-step method through fixing the metal Ni(0) reduced by a specific reducing agent (N 2 H 4 ·H 2 O) on the surface of the BaTiO 3 particles with grain diameter of ∼500 nm. BaTiO 3 /Ni particle has double responses of electric and magnetic field simultaneously. Consequentially, coating magnetic metal on BT particle is proposed an effective method to prepare novel electro-magneto responsive particles and one basis of electro-magneto responsive elastomers. - Highlights: • The BaTiO 3 /Ni composite particles were fabricated. • The content of Ni(0) in nickel sheath is 70.2%. • The BaTiO 3 /Ni particles have double responses of electric and magnetic field. - Abstract: BaTiO 3 (BT)/Ni composite particles were made by one-step method through agglomerating the metal Ni(0) nanoparticles reduced by a specific reducing agent (N 2 H 4 ·H 2 O) on the surface of BT sphere with diameter of ∼500 nm. The BT/Ni composite particles were characterized by the means of scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray diffractometer (XRD) and X-ray photoelectron spectroscopy (XPS). In BT/Ni particles, pure BT spherical particle was coated with Ni nanoparticles agglomerated on its surface. The average thickness of the Ni sheath was ∼30 nm and the content of Ni(0) and Ni (II) in the sheath were 70.2% and 29.8%, respectively. The responsive effects of BT/Ni particles filled in hydrogel elastomer were investigated by the viscoelastic properties. The results indicate that the BT/Ni particles exhibit electro and magneto coordinated responsive properties (E = 1 kV/mm, H = 0.1 T/mm), which is superior to BT particles with individual electro response.

  13. Enhancement of polarization property of silane-modified BaTiO3 nanoparticles and its effect in increasing dielectric property of epoxy/BaTiO3 nanocomposites

    Directory of Open Access Journals (Sweden)

    Thi Tuyet Mai Phan

    2016-03-01

    Full Text Available The surface modification of synthesized nano-BaTiO3 particles was carried out using γ-aminopropyl trimethoxy silane (γ-APS in an ethanol/water solution. The modified particles were characterized by FTIR, TGA, surface charge analysis, and by dielectric constant measurement. The silane molecules were attached to the surface of BaTiO3 particles through SiOBaTiO3 bonds. The γ-APS grafted on BaTiO3 made the dielectric constant of the particles increase at frequencies ≥0.3 kHz in a wide range of temperature (25 °C–140 °C, due to the presence of NH2 groups. The dependence of the polarization vs. electrical field was measured in order to elucidate the dielectric behavior of the silane treated BaTiO3 in comparison to untreated BaTiO3. The nanocomposite based on epoxy resin containing BaTiO3 nanoparticles untreated and treated with γ-APS was also prepared and characterized. The results indicated that the γ-APS-modified BaTiO3 surfaces significantly enhanced the dielectric property of the nanocomposite.

  14. Fabrication and properties of yttria, ceria doped zirconia-aluminia ceramic composites

    International Nuclear Information System (INIS)

    Lyubushkin, R.A.; Ivanov, O.N.; Chuev, V.P.; Buzov, A.A.

    2011-01-01

    At present, zirconia-based ceramics are gaining popularity in dentistry, particularly in fixed prosthodontics. clinically, it is important that ceramic restorations reproduce the translucency and color of natural teeth. Zirconia based ceramics is a high performance material with excellent biocompatibility and mechanical properties, which suggest its suitability for posterior fixed partial dentures. Y 2 O 3 -stabilized tetragonal zirconia polycrystalline (YTZ/Al 2 O 3 ) and CeO 2 -stabilized tetragonal zirconia polycrystalline (CZA) ceramics with high-performance were prepared for dental application by use the wet chemical route, consolidated by cold isostatic pressing, and two-step sintering method. Physical and mechanical properties test results show that the bending strength, fracture toughness, and the density of full sintered ceramics suggest that the material is relatively suitable for dental restoration.

  15. Toughening behavior in ceramics associated with the transformation of tetragonal ZrO/sub 2/

    International Nuclear Information System (INIS)

    Becher, P.F.

    1986-01-01

    The contribution of the stress-induced phase transformation ZrO/sub 2/ to the fracture toughness of ceramics is described in terms of the zone size, the critical transformation stress and the influence of these parameters on the tetragonal to monoclinic transformation. For example in partially stabilized zirconia (PSZ), the ΔK/sub lC//sup T/ is shown to depend upon the martensite start (M/sub s/) temperature, which can be altered by the solute content and the particle or precipitate size. This behavior is consistent with the thermodynamics of the transformation. Experimental data correspond to the behavior predicted for various systems toughened by the addition of tetragonal ZrO/sub 2/ [e.g. PSZ and Al/sub 2/O/sub 3/-Z/sub 4/O/sub 2/(Y/sub 2/O/sub 3/). The stress required to transform the ZrO/sub 2/ is also modified by residual stresses due to the mismatch in matrix and particle (esp. thermal expansion) properties in the composite systems. The total residual stress acting on a particle is the sum of the particle's internal stress and the stress field of neighboring particles, and as a result, the total residual stress increases with volume fraction of ZrO/sub 2/ (V/sub f/). In the case of the Al/sub 2/O/sub 3/-ZrO/sub 2/ composites the pertinent stresses are tensile in character and thus promote the ZrO/sub 2/ transformation as V/sub f/ increases] For each level of Y/sub 2/O/sub 3/ in the ZrO/sub 2/, ΔK/sub lc//sup T/ then goes through a maximum with increase in V/sub f/ at a value of V/sub f/ where σ/sub R//sup T/ - σ/sub C//sup T/. The critical transformation stress is thus described for different levels of solute (e.g. Y/sub 2/O/sub 3/) in the ZrO/sub 2/. The dependence of ΔK/sub lc//sup T/ upon (σ/sub C//sup T/ - σ/sub R//sup T/) obtained is found to agree with the predicted behavior

  16. Strong magnetoelectric coupling in CoFe2O4-BaTiO3 composites prepared by molten-salt synthesis method

    International Nuclear Information System (INIS)

    Nie Junwu; Xu Guoyue; Yang Ying; Cheng Chuanwei

    2009-01-01

    Magnetoelectric nano-composites (1 - x)CoFe 2 O 4 + (x)BaTiO 3 with x varies as 0, 0.5, 0.65 and 1.0 in molar ratio were prepared by molten-salt synthesis method. The structural analysis carried out by X-ray diffraction (XRD) technique has confirmed that both phases are present in all the nano-composites powders and ceramic composites. The TEM images show that the nano-particle crystallite size is about 50-80 nm, which is consistent to the result calculated by XRD. The dielectric constant was studied as a function of frequency for ceramic composites sintered by using those nano-composite powders. The saturation magnetization (Ms) and remnant polarization (Pr) were calculated from the magnetic hysteresis loop and electric hysteresis loop, respectively. And a large ME coefficient of about 17.04 mV cm -1 Oe -1 was observed for 0.5CoFe 2 O 4 + 0.5BaTiO 3 ME composite under the ac superimposed magnetic signal with 20 kHz frequency by using the lock-in technique

  17. X-ray diffraction and dielectric studies across morphotropic phase boundary in (1 - x) [Pb(Mg0.5W0.5)O3]-xPbTiO3 ceramics

    International Nuclear Information System (INIS)

    Singh, A.K.; Singh, Akhilesh Kumar

    2011-01-01

    Research highlights: → Structural studies reveal pseudocubic structure of PMW-xPT for the x ≤ 0.42, tetragonal for the x ≥ 0.72 and the coexistences of the two phases for intermediate compositions (0.46 ≤ x 0.68). → Temperature dependent dielectric constant for compositions in the two phase region shows two dielectric anomalies above room temperature and not just one as reported by earlier workers. → Rietveld structural analysis of PMW-xPT ceramics is presented for the first time to determine the fraction of the coexisting phases in MPB region. - Abstract: We present here the results of comprehensive X-ray diffraction and dielectric studies on several compositions of (1 - x)[Pb(Mg 0.5 W 0.5 )O 3 ]-xPbTiO 3 (PMW-xPT) solid solution across the morphotropic phase boundary. Rietveld analysis of the powder X-ray diffraction data reveals cubic (space group Fm3m) structure of PMW-xPT ceramics for the compositions with x ≤ 0.42, tetragonal (space group P4mm) structure for the compositions with x ≥ 0.72 and coexistence of the tetragonal and cubic phases for the intermediate compositions (0.46 ≤ x ≤ 0.68). Temperature dependence of the dielectric permittivity above room temperature exhibits diffuse nature of phase transitions for the compositions in the cubic and two phase region while the compositions with tetragonal structure at room temperature exhibit sharp ferroelectric to paraelectric phase transition. The PMW-xPT compositions with coexistence of tetragonal and cubic phases at room temperature exhibit two anomalies in the temperature dependence of the dielectric permittivity above room temperature. Using results of structural and dielectric studies a partial phase diagram of PMW-xPT ceramics is also presented.

  18. Ferroelectricity of strained SrTiO3 in lithium tetraborate glass-nanocomposite and glass-ceramic

    Science.gov (United States)

    Abdel-Khalek, E. K.; Mohamed, E. A.; Kashif, I.

    2018-02-01

    Glass-nanocomposite (GNCs) sample of the composition [90Li2B4O7-10SrTiO3] (mol %) was prepared by conventional melt quenching technique. The glassy phase and the amorphous nature of the GNCs sample were identified by Differential thermal analysis (DTA) and X-ray diffraction (XRD) studies, respectively. DTA of the GNCs exhibits sharp and broad exothermic peaks which represent the crystallization of Li2B4O7 and SrTiO3, respectively. The tetragonal Li2B4O7 and tetragonal SrTiO3 crystalline phases in glass-ceramic (GC) were identified by XRD and scanning electron microscopic (SEM). The strain tetragonal SrTiO3 phase in GNCs and GC has been confirmed by SEM. The values of crystallization activation energies (Ec1 and Ec2) for the first and second exothermic peaks are equal to 174 and 1452 kJ/mol, respectively. The Ti3+ ions in tetragonal distorted octahedral sites in GNCs were identified by optical transmission spectrum. GNCs and GC samples exhibit broad dielectric anomalies at 303 and 319 K because of strained SrTiO3 ferroelectric, respectively.

  19. Hydrothermal degradation of tetragonal ZrO{sub 2} ceramic components used in dental applications; Efeito da degradacao em meio aquoso de componentes ceramicos a base de ZrO{sub 2} tetragonal para uso odontologico

    Energy Technology Data Exchange (ETDEWEB)

    Mukaeda, L.E.; Robin, A.; Taguchi, S.P. [Universidade de Sao Paulo (DEMAR/EEL/USP), Lorena, SP (Brazil). Escola de Engenharia de Lorena. Dept. de Engenharia de Materiais; Santos, C. [ProtMat Materiais Avancados, Guaratingueta, SP (Brazil)

    2009-07-01

    With the evolution of the dental restoration techniques, a considerable growth in the demand of ceramic products occurred. These materials present good strength associated to reliability. In this work, micrometric and nanometric scale tetragonal ZrO{sub 2} blocks were sintered at 1500 deg C-2h and 1350 deg C-2h, respectively, ground and polished. Ceramics with relative density higher than 98% were obtained. The specimens were immersed in hot water (150 deg C), for times ranging from 10h to 30h. The mass variation of the samples was measured and the crystalline phases present before and after the degradation tests were identified by X-ray diffractometry, in order to evaluate the capacity of these ceramics in resisting to aqueous medium exposure. Materials with nanometric structure present higher resistance to degradation than those with micrometric scale, and this interferes in structural stability after the test, and reduces the martensitic transformation. (author)

  20. Preparation and electrical properties of Bi0.5Na0.5TiO3-BaTiO3-KNbO3 lead-free piezoelectric ceramics

    International Nuclear Information System (INIS)

    Ni Haimin; Luo Laihui; Li Weiping; Zhu Yuejin; Luo Haosu

    2011-01-01

    Research highlights: → Bi 0.47 Na 0.47 Ba 0.06 TiO 3 -KNbO 3 ceramics exhibit excellent piezoelectric properties. → The optimized properties of the ceramics: d 33 = 195 pC/N; k t = 58.9; Q m = 113; E c = 19.5 kV/cm. → KNbO 3 has diffused into the Bi 0.47 Na 0.47 Ba 0.06 TiO 3 lattices to form a new solid solution. → Macro-micro domain switching occurs at depolarization temperature T d . - Abstract: Lead-free (1 - x)Bi 0.47 Na 0.47 Ba 0.06 TiO 3 -xKNbO 3 (BNBT-xKN, x = 0-0.08) ceramics were prepared by ordinary ceramic sintering technique. The piezoelectric, dielectric and ferroelectric properties of the ceramics are investigated and discussed. The results of X-ray diffraction (XRD) indicate that KNbO 3 (KN) has diffused into Bi 0.47 Na 0.47 Ba 0.06 TiO 3 (BNBT) lattices to form a solid solution with a pure perovskite structure. Moderate additive of KN (x ≤ 0.02) in BNBT-xKN ceramics enhance their piezoelectric and ferroelectric properties. Three dielectric anomaly peaks are observed in BNBT-0.00KN, BNBT-0.01KN and BNBT-0.02KN ceramics. With the increment of KN in BNBT-xKN ceramics, the dielectric anomaly peaks shift to lower temperature. BNBT-0.01KN ceramic exhibits excellent piezoelectric properties and strong ferroelectricity: piezoelectric coefficient, d 33 = 195 pC/N; electromechanical coupling factor, k t = 58.9 and k p = 29.3%; mechanical quality factor, Q m = 113; remnant polarization, P r = 41.8 μC/cm 2 ; coercive field, E c = 19.5 kV/cm.

  1. Electrical properties of (1 0 0)-predominant BaTiO3 films derived from alkoxide solutions of two concentrations

    International Nuclear Information System (INIS)

    Guo Yiping; Suzuki, Kazuyuki; Nishizawa, Kaori; Miki, Takeshi; Kato, Kazumi

    2006-01-01

    Lead-free piezoelectric films with thickness larger than 1 μm integrated on silicon substrates have been receiving considerable attention because of environmental concerns and their potential applications in microelectromechanical systems. We demonstrate that, by chemical solution deposition, it is possible to process (1 0 0)-predominant 1 μm BaTiO 3 films on LaNiO 3 /Pt/TiO x /SiO 2 /Si substrates using thinner high-crystallinity columnar BaTiO 3 films as buffer layers. We point out that this kind of buffer layer prepared with a lower concentration solution on the surface of an LaNiO 3 /Pt electrode is effective in enhancing the crystallinity and orientation degree of final BaTiO 3 films prepared with a higher concentration solution. The 1 μm BaTiO 3 films show good dielectric and insulating characteristics against an applied field, and the conduction current shows Schottky emission behavior at modest voltage and space-charge-limited behavior at higher voltage. We also demonstrate that the (1 0 0)-predominant 1 μm BaTiO 3 films have excellent piezoelectric properties: piezoelectric coefficients d 33 higher than 50 pm/V have been determined for the bare films using atomic force microscopy, which are comparable to those of Pb(Zr,Ti)O 3 films. These results indicate that the (1 0 0)-predominant BaTiO 3 films should be promising candidates for microelectromechanical systems applications

  2. Ab Initio Calculations for the BaTiO3 (001) Surface Structure

    Institute of Scientific and Technical Information of China (English)

    XUE Xu-Yan; WANG Chun-Lei; ZHONG Wei-Lie

    2004-01-01

    @@ The ab initio method within the local density approximation is applied to calculate cubic BaTiO3 (001) surface relaxation and rumpling for two different terminations (BaO and TiO2). Our calculations demonstrate that cubic perovskite BaTiO3 crystals possess surface polarization, accompanied by the presence of the relevant electric field.We analyse their electronic structures (band structure, density of states and the electronic density redistribution with emphasis on the covalency effects). The results are also compared with that of the previous ab initio calculations. Considerable increases of Ti-O chemical bond covalency nearby the surface have been observed.The band gap reduces especially for the TiO2 termination.

  3. Preparation and properties of yttria doped tetragonal zirconia polycrystal/Sr-doped barium hexaferrite ceramic composites

    International Nuclear Information System (INIS)

    Wang, Shanshan; Zhang, Chao; Guo, Ruisong; Liu, Lan; Yang, Yuexia; Li, Kehang

    2015-01-01

    Highlights: • The 3Y-TZP/Sr-doped barium ferrite composites were prepared. • The saturation magnetization was improved by 15% with Sr-doping. • The dispersion coefficient p could reflect the microscopic lattice variation. • The composite with x = 0.5 had the maximum fracture toughness of 8.3 MPa m 1/2 . - Abstract: The effects of substitution of Ba 2+ by Sr 2+ on the magnetic property of barium ferrite and addition barium ferrite secondary phase to the 3 mol% yttria-doped tetragonal zirconia polycrystal (3Y-TZP) matrix on the mechanical property of composites were investigated. The Sr-doped barium ferrite (Ba 1−x Sr x Fe 12 O 19 , x = 0, 0.25, 0.50 and 0.75) was synthesized by solid-state reaction in advance. Then 3Y-TZP/20 wt% Sr-doped barium ferrite composites were prepared by means of conventional ceramic method. It was found that a moderate amount of Sr added to barium ferrite could boost the saturation magnetization by 15% compared with the composites without Sr-doping. Besides, the composite with x = 0.50 possessed the best mechanical properties, such as 11.5 GPa for Vickers hardness and 8.3 MPa m 1/2 for fracture toughness, respectively. It was demonstrated that magnetic and mechanical properties of the composites could be harmonized by the incorporation of barium ferrite secondary phase

  4. Ferroelectric properties of composites containing BaTiO3 nanoparticles of various sizes

    International Nuclear Information System (INIS)

    Adam, Jens; Lehnert, Tobias; Klein, Gabi; McMeeking, Robert M

    2014-01-01

    Size effects, including the occurrence of superparaelectric phases associated with small scale, are a significant research topic for ferroelectrics. Relevant phenomena have been explored in detail, e.g. for homogeneous, thin ferroelectric films, but the related effects associated with nanoparticles are usually only inferred from their structural properties. In contrast, this paper describes all the steps and concepts necessary for the direct characterization and quantitative assessment of the ferroelectric properties of as-synthesized and as-received nanoparticles. The method adopted uses electrical polarization measurements on polymer matrix composites containing ferroelectric nanoparticles. It is applied to ten different BaTiO 3 particle types covering a size range from 10 nm to 0.8 μm. The influence of variations of particle characteristics such as tetragonality and dielectric constant is considered based on measurements of these properties. For composites containing different particle types a clearly differing polarization behaviour is found. For decreasing particle size, increasing electric field is required to achieve a given level of polarization. The size dependence of a measure related to the coercive field revealed by this work is qualitatively in line with the state of the knowledge for ferroelectrics having small dimensions. For the first time, such results and size effects are described based on data from experiments on collections of actual nanoparticles. (paper)

  5. Ferroelectric properties of composites containing BaTiO 3 nanoparticles of various sizes

    Science.gov (United States)

    Adam, Jens; Lehnert, Tobias; Klein, Gabi; McMeeking, Robert M.

    2014-01-01

    Size effects, including the occurrence of superparaelectric phases associated with small scale, are a significant research topic for ferroelectrics. Relevant phenomena have been explored in detail, e.g. for homogeneous, thin ferroelectric films, but the related effects associated with nanoparticles are usually only inferred from their structural properties. In contrast, this paper describes all the steps and concepts necessary for the direct characterization and quantitative assessment of the ferroelectric properties of as-synthesized and as-received nanoparticles. The method adopted uses electrical polarization measurements on polymer matrix composites containing ferroelectric nanoparticles. It is applied to ten different BaTiO3 particle types covering a size range from 10 nm to 0.8 μm. The influence of variations of particle characteristics such as tetragonality and dielectric constant is considered based on measurements of these properties. For composites containing different particle types a clearly differing polarization behaviour is found. For decreasing particle size, increasing electric field is required to achieve a given level of polarization. The size dependence of a measure related to the coercive field revealed by this work is qualitatively in line with the state of the knowledge for ferroelectrics having small dimensions. For the first time, such results and size effects are described based on data from experiments on collections of actual nanoparticles.

  6. Piezoelectric properties and thermal stability of (Na0.53K0.47-xAgx)Nb1-xSbxO3 ceramics

    International Nuclear Information System (INIS)

    Zheng, Limei; Wang, Jinfeng; Wang, Chunming; Gai, Zhigang; Wu, Qingzao; Zhang, Rui

    2011-01-01

    Many (K 1-x Na x )NbO 3 (KNN)-based ceramics with high piezoelectric performance exhibit undesirable strong temperature dependence due to the orthorhombic-tetragonal polymorphic phase transition near room temperature. In order to improve the temperature stability of the ceramics, many additives have been added into the KNN-based ceramics to shift T O-T down to below room temperature. Contrary to the previous approach (Na 0.53 K 0.47-x Ag x )Nb 1-x Sb x O 3 (NKANS) ceramics with T O-T well above room temperature have been prepared by a conventional solid-state reaction method. The density and the electrical properties are effectively improved by the addition of AgSbO 3 , and optimum piezoelectric properties are found in the ceramics with 0.05 ≤ x ≤ 0.07, with maximum k p ∝ 0.46 for NKANS5 and maximum d 33 ∝ 199 pC/N for NKANS7. More importantly, k p remains virtually almost unchanged up to the T O-T temperature (≥100 C), indicating that the NKANS ceramics exhibit a much improved piezoelectric thermal stability. The analyses suggest that both the high T O-T value and diffuse orthorhombic-tetragonal phase transition should be responsible for the good temperature stability. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  7. Pressure induced phase transitions in ceramic compounds containing tetragonal zirconia

    Energy Technology Data Exchange (ETDEWEB)

    Sparks, R.G.; Pfeiffer, G.; Paesler, M.A.

    1988-12-01

    Stabilized tetragonal zirconia compounds exhibit a transformation toughening process in which stress applied to the material induces a crystallographic phase transition. The phase transition is accompanied by a volume expansion in the stressed region thereby dissipating stress and increasing the fracture strength of the material. The hydrostatic component of the stress required to induce the phase transition can be investigated by the use of a high pressure technique in combination with Micro-Raman spectroscopy. The intensity of Raman lines characteristic for the crystallographic phases can be used to calculate the amount of material that has undergone the transition as a function of pressure. It was found that pressures on the order of 2-5 kBar were sufficient to produce an almost complete transition from the original tetragonal to the less dense monoclinic phase; while a further increase in pressure caused a gradual reversal of the transition back to the original tetragonal structure.

  8. Ferroelastic domain switching in tetragonal zirconia

    International Nuclear Information System (INIS)

    Chan, C.J.; Ruhle, M.; Jue, J.F.; Virkar, A.V.

    1991-01-01

    Ferroelastic domain switching is one of the possible toughening mechanisms in ceramic materials. Microstructural evidence of domain reorientation (switching) in polydomain tetragonal zirconia single crystals is observed upon the application of a unidirectional compressive stress. Dark field imaging of the three (112) tetragonal twin variants in a [111] zone indicates that two sets of twin variants grow at the expense of the third set upon application of uniaxial compression. The diminishing variant is the one with its c axis parallel to the compression axis. Indentation experiments on uniaxially compressed samples show an anisotropy in crack length. Crack propogates more easily along the loading direction. In this paper construction for the orientation relationship of domains and their twin boundaries is presented

  9. Tetragonal-to-Tetragonal Phase Transition in Lead-Free (KxNa1−xNbO3 (x = 0.11 and 0.17 Crystals

    Directory of Open Access Journals (Sweden)

    Dabin Lin

    2014-06-01

    Full Text Available Lead free piezoelectric crystals of (KxNa1−xNbO3 (x = 0.11 and 0.17 have been grown by the modified Bridgman method. The structure and chemical composition of the obtained crystals were determined by X-ray diffraction (XRD and electron probe microanalysis (EPMA. The domain structure evolution with increasing temperature for (KxNa1−xNbO3 (x = 0.11 and 0.17 crystals was observed using polarized light microscopy (PLM, where distinguished changes of the domain structures were found to occur at 400 °C and 412 °C respectively, corresponding to the tetragonal to tetragonal phase transition temperatures. Dielectric measurements performed on (K0.11Na0.89NbO3 crystals exhibited tetragonal to tetragonal and tetragonal to cubic phase transitions temperatures at 405 °C and 496 °C, respectively.

  10. Interface control in BaTiO3 based supercapacitors

    Science.gov (United States)

    Maglione, Mario; Elissalde, Catherine; Chung, U.-Chan

    2010-03-01

    Core shell BaTiO3 based particles sintered using advanced processes provide a high control of grain boundaries in bulk composites. As a result, supercapacitor behavior was evidenced which came from the balance between inner grain conductivity and grain boundary dielectric barrier. Thanks to the core-shell structure of the starting particles, improved control of the effective dielectric parameters can be achieved.

  11. Ferroelectric BaTiO3 and LiNbO3 Nanoparticles Dispersed in Ferroelectric Liquid Crystal Mixtures: Electrooptic and Dielectric (Postprint)

    Science.gov (United States)

    2016-10-14

    strength for non- doped LF4 and LiNbO3/LF4 nanocolloids at temperature 30C. 146 R. K . SHUKLA ET AL. 6 Distribution A. Approved for public release (PA...AFRL-RX-WP-JA-2017-0210 FERROELECTRIC BaTiO3 AND LiNbO3 NANOPARTICLES DISPERSED IN FERROELECTRIC LIQUID CRYSTAL MIXTURES: ELECTROOPTIC...COMMAND UNITED STATES AIR FORCE Ferroelectric BaTiO3 and LiNbO3 nanoparticles dispersed in ferroelectric liquid crystal mixtures: Electrooptic and

  12. Properties of TiO2 prepared by acid treatment of BaTiO3

    International Nuclear Information System (INIS)

    Okada, Kiyoshi; Yanagisawa, Tomoki; Kameshima, Yoshikazu; Nakajima, Akira

    2007-01-01

    TiO 3 powders were prepared by acid treatment of BaTiO 3 and their properties were investigated. The BaTiO 3 powder was subjected to HNO 3 in concentrations ranging from 10 -3 to 8 M at 90 deg. C for 0.5-6 h. Dissolution of BaTiO 3 and precipitation of TiO 2 occurred at acid concentrations of 2-5 M. BaTiO 3 dissolves completely to form a clear solution at reaction times of 0.5-1 h, but a rutile precipitate is formed after 2 h of acid treatment. By contrast, anatase is precipitated by adjusting the pH of the clear solution to 2-3 using NaOH or NH 4 OH solution. The rutile crystals were small and rod-shaped, consisting of many small coherent domains connected by grain boundaries with small inclination angles and edge dislocations, giving them a high specific surface area (S BET ). With increasing HNO 3 concentration, the S BET value increased from 100 to 170 m 2 /g while the crystallite size decreased from 25 to 11 nm. The anatase crystals obtained here were very small equi-axial particles with a smaller crystallite size than the rutile and S BET values of about 270 m 2 /g (higher than the rutile samples). The photocatalytic activity of these TiO 2 was determined from the decomposition rate of Methylene Blue under ultraviolet irradiation. Higher decomposition rates were obtained with larger crystallite sizes resulting from heat treatment. The maximum decomposition rates were obtained in samples heated at 500-600 deg. C. The photocatalytic activity of the TiO 2 was found to depend more strongly on the sample crystallite size than on S BET

  13. Electrical properties and temperature stability of a new kind of lead-free piezoelectric ceramics

    International Nuclear Information System (INIS)

    Wang Yuanyu; Wu Jiagang; Xiao Dingquan; Zhang Bin; Wu Wenjuan; Shi Wei; Zhu Jianguo

    2008-01-01

    0.995[(K 0.50 Na 0.50 ) 0.94 Li 0.06 ]NbO 3 -0.005AETiO 3 (AE=Ca, Sr, Mg, Ba) lead-free piezoelectric ceramics were prepared by normal sintering. The effects of the AETiO 3 and poling temperature on the electrical properties of the ceramics were carefully studied, and the temperature stability of the electrical properties of the ceramics was also investigated. The experimental results show that the ceramics with Li and CaTiO 3 possess the pure phase, Li and AETiO 3 improves the electrical properties of the pure (K 0.50 Na 0.50 )NbO 3 ceramics, the poling temperature near tetragonal and orthorhombic phase transition will enhance the piezoelectric properties of the ceramics and the KNLN-CT ceramics exhibit good temperature stability of electrical properties for tetragonal and orthorhombic phase transition below room temperature. The KNLN-CT ceramics exhibit relatively good properties: d 33 = 172 pC N -1 , k p = 0.43, tan δ = 0.032, ε r = 771 and T c = 465 deg. C. As a result, the KNLN-CT ceramic is promising candidate material for piezoelectric devices.

  14. The phase stability and toughening effect of 3Y-TZP dispersed in the lanthanum zirconate ceramics

    International Nuclear Information System (INIS)

    Wang, Yanfei; Xiao, Ping

    2014-01-01

    The low fracture toughness of lanthanum zirconate (La 2 Zr 2 O 7 , LZ) greatly impedes its wide application as thermal barrier coatings (TBC). The 3 mol% Y 2 O 3 -stabilized tetragonal zirconia polycrystals (3Y-TZP) have been introduced to toughen the brittle LZ ceramics. The dispersive 3Y-TZP undergoes a simultaneous t–m transformation upon cooling below a critical volume fraction x of 3Y-TZP, above which its tetragonal phases can however be preserved. The different stabilities of 3Y-TZP second phases arise from a variation of residual tensile stress within them. The fracture toughness has been greatly improved by dispersing the tetragonal particulates (t-3YSZ) in the LZ matrix and the primary toughening mechanisms are phase transformations of the dispersive second phases and the residual compressive stress within the matrix. An anticipated increase of fracture toughness from the ferroelastic toughening and the residual compressive stress toughening highlights the great potentials to improve coating durability by depositing t′-3YSZ/LZ composite TBCs by the industrial non-equilibrium route

  15. Morphology controlled ultrafine BaTiO3 based PVDF-HFP ...

    Indian Academy of Sciences (India)

    21

    ... for real applications. Kew Words: Polygonal, Barium Titanate, Hydrothermal, Dielectric and Sensor. 1. 2 ... structure and can be tuned further by substituting various dopants (Sr, Ca and Zr). .... Modified BaTiO3 induces less displacement of Ti and O ions along c- axis and .... sputter coated on both sides with gold. The films ...

  16. Study of grain boundary tunneling in barium-titanate ceramic films

    CERN Document Server

    Wong, H; Poon, M C

    1999-01-01

    The temperature and the electric-field dependences of the current-voltage characteristics and the low-frequency noise of barium-titanate ceramic films are studied. An abnormal field dependence is observed in the resistivity of BaTiO sub 3 materials with a small average grain size. In addition, experiments show that the low-frequency noise behaviors are governed by grain-boundary tunneling at room temperature and by trapping-detrapping of grain-boundary states at temperatures above the Curie point. Physical models for the new observations are developed. Results suggest that grain-boundary tunneling of carriers is as important as the double Schottky barrier in the current conduction in BaTiO sub 3 materials with small grain sizes.

  17. Barium titanate nanometric polycrystalline ceramics fired by spark plasma sintering.

    Czech Academy of Sciences Publication Activity Database

    Ctibor, Pavel; Sedláček, J.; Ryukhtin, Vasyl; Cinert, Jakub; Lukáč, František

    2016-01-01

    Roč. 42, č. 14 (2016), s. 15989-15993 ISSN 0272-8842 R&D Projects: GA ČR GB14-36566G; GA MŠk LM2015056 Institutional support: RVO:61389021 ; RVO:61389005 Keywords : BaTiO3 * Spark plasma sintering * Electrical properties Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass; JH - Ceramics, Fire-Resistant Materials and Glass (UJF-V) Impact factor: 2.986, year: 2016 http://www.sciencedirect.com/science/article/pii/S0272884216311695

  18. Highly uniform bipolar resistive switching characteristics in TiO2/BaTiO3/TiO2 multilayer

    International Nuclear Information System (INIS)

    Ma, W. J.; Zhang, X. Y.; Wang, Ying; Zheng, Yue; Lin, S. P.; Luo, J. M.; Wang, B.; Li, Z. X.

    2013-01-01

    Nanoscale multilayer structure TiO 2 /BaTiO 3 /TiO 2 has been fabricated on Pt/Ti/SiO 2 /Si substrate by chemical solution deposition method. Highly uniform bipolar resistive switching (BRS) characteristics have been observed in Pt/TiO 2 /BaTiO 3 /TiO 2 /Pt cells. Analysis of the current-voltage relationship demonstrates that the space-charge-limited current conduction controlled by the localized oxygen vacancies should be important to the resistive switching behavior. X-ray photoelectron spectroscopy results indicated that oxygen vacancies in TiO 2 play a crucial role in the resistive switching phenomenon and the introduced TiO 2 /BaTiO 3 interfaces result in the high uniformity of bipolar resistive switching characteristics

  19. Luminescent Properties of Surface Functionalized BaTiO3 Embedded in Poly(methyl methacrylate)

    Science.gov (United States)

    Requena, Sebastian; Lacoul, Srijan; Strzhemechny, Yuri M.

    2014-01-01

    As-received BaTiO3 nanopowders of average grain sizes 50 nm and 100 nm were functionalized by (3-aminopropyl)triethoxysilane (APTES) and mixed with poly(methyl methacrylate)/toluene solution. The nanocomposite solution was spin coated on Si substrates to form thin films. The photoluminescence spectrum of the pure powder was composed of a bandgap emission at 3.0 eV and multiple bands centered about 2.5 eV. Surface functionalization of the BaTiO3 powder via APTES increases overall luminescence at room temperature while only enhancing bandgap emission at low-temperature. Polymer coating of the functionalized nanoparticles significantly enhances bandgap emissions while decreasing emissions associated with near-surface lattice distortions at 2.5 eV. PMID:28788468

  20. Luminescent Properties of Surface Functionalized BaTiO3 Embedded in Poly(methyl methacrylate

    Directory of Open Access Journals (Sweden)

    Sebastian Requena

    2014-01-01

    Full Text Available As-received BaTiO3 nanopowders of average grain sizes 50 nm and 100 nm were functionalized by (3-aminopropyltriethoxysilane (APTES and mixed with poly(methyl methacrylate/toluene solution. The nanocomposite solution was spin coated on Si substrates to form thin films. The photoluminescence spectrum of the pure powder was composed of a bandgap emission at 3.0 eV and multiple bands centered about 2.5 eV. Surface functionalization of the BaTiO3 powder via APTES increases overall luminescence at room temperature while only enhancing bandgap emission at low-temperature. Polymer coating of the functionalized nanoparticles significantly enhances bandgap emissions while decreasing emissions associated with near-surface lattice distortions at 2.5 eV.

  1. BaTiO3–P(VDF-HFP) nanocomposite dielectrics—Influence of surface modification and dispersion additives

    International Nuclear Information System (INIS)

    Ehrhardt, Claudia; Fettkenhauer, Christian; Glenneberg, Jens; Münchgesang, Wolfram; Pientschke, Christoph; Großmann, Thomas; Zenkner, Mandy; Wagner, Gerald; Leipner, Hartmut S.; Buchsteiner, Alexandra; Diestelhorst, Martin; Lemm, Sebastian; Beige, Horst; Ebbinghaus, Stefan G.

    2013-01-01

    Highlights: • Polymer composites were prepared using a sol–gel synthesized BaTiO 3 . • BaTiO 3 surface hydroxyle groups act as linkers for surfactant molecules. • The effect of chemical adjustment between surfactant and polymer host is studied. • A positive effect of an additional dispersant was found. • Dielectric properties of the resulting composite films are presented. -- Abstract: We report on BaTiO 3 –polymer composites as dielectrics for film capacitors. BaTiO 3 was synthesized by a sol–gel soft-chemistry method leading to spherical nanoparticles with a high degree of surface hydroxyl groups which turned out to be important for the bonding of surfactant molecules. As surfactants, n-octylphosphonic acid and 2,3,4,5,6-pentafluorobenzyl phosphonic acid were used to inhibit particle agglomeration and to improve the wetting behaviour with the polymer. The phosphonic acid-coated BaTiO 3 nanoparticles were dispersed in solutions of poly(vinylidefluoride-co-hexafluoropropylene). Composite films were prepared by the spin-coating technique. A systematic study was performed on the influence of varying oxide fractions, different surfactants and the effect of additional dispersion aids such as sodium dodecyl sulphate or BYK-W 9010 on the quality and dielectric properties of the films obtained. The chemical adjustment of the 2,3,4,5,6-pentaflourobenzyl phosphonic acid within the fluorinated organic host form a more uniform particle distribution and increase relative permittivity of the resulting composite material compared to the unflourinated surfactant. Additionally, an enhancement of the relative permittivity can be realized by adding of dispersants. These two components can increase the relative permittivity by factor 5 compared to the pure polymer material

  2. Optical Second Harmonic Generation in the BaTiO3 phase of magnetically aligned multiferroic nanofibers

    Science.gov (United States)

    Gasperi, Katia

    Multiferroic materials enable the exploration of electrical control of magnetic properties and vice versa. Their increasing interest is especially due to their potential applications in the industry of information storage. Thanks to recent progress in nanotechnology, they have also been found to have many other applications such as transducers and sensors, and they already occupy a unique place in the biomedical field. The objective of this project is to study multiferroic nanofibers made of cobalt ferrite CoFe2O 4 (CFO) and barium titanate BaTiO3 (BTO) with a specific focus in the characterization of the ferroelectric phase. We researched the state of knowledge concerning the size effects on phase transition for nanoparticles and polycrystals BTO. The ferroelectric phase transition of BTO occurs when it changes from a tetragonal (anisotropic) crystal structure to a cubic (isotropic) structure. This change suggests that optical second harmonic generation (SHG) is a good measurement technique for monitoring the phase transition of the BTO half of the nanofibers. We designed and prepared a temperature dependent SHG experiment on magnetically aligned fibers in transmission with the possibility to investigate the polarization dependence of the signal. We also prepared interdigital electrodes on glass for the future study of the fibers in an external electric field.

  3. CeO2-ZrO2 ceramic compounds

    International Nuclear Information System (INIS)

    Melo, F.C.L.; Cairo, C.A.C.; Devezas, T.C.; Nono, M.C.A.

    1988-01-01

    In order to study the mechanical properties of tetragonal polycrystal zirconia stabilized with ceria various powder compositions with different CeO 2 content were made. Modulus of rupture for those compounds was measured. Tetragonal retained phase was determined for samples of CeO 2 -ZrO 2 ceramics with and without superficial mechanical treatment. The experimental results allowed us to evaluate the effects of CeO 2 content and sintering temperature in the mechanical properties and tetragonal transformed phase (t→ m) in ceramics of CeO 2 -ZrO 2 systems. (author) [pt

  4. Magneto electric effects in BaTiO3-CoFe2O4 bulk composites

    Science.gov (United States)

    Agarwal, Shivani; Caltun, O. F.; Sreenivas, K.

    2012-11-01

    Influence of a static magnetic field (HDC) on the hysteresis and remanence in the longitudinal and transverse magneto electric voltage coefficients (MEVC) observed in [BaTiO3]1-x-[CoFe2O4]x bulk composites are analyzed. Remanence in MEVC at zero bias (HDC=0) is stronger in the transverse configuration over the longitudinal case. The observed hysteretic behavior in MEVC vs. HDC is correlated with the changes observed in the magnetostriction characteristics (λ and dλ/dH) reported for [BaTiO3]1-x-[CoFe2O4]x bulk composites.

  5. Growth of Ca, Zr co-doped BaTiO3 lead-free ferroelectric single crystal and its room-temperature piezoelectricity

    Directory of Open Access Journals (Sweden)

    Donglin Liu

    2017-09-01

    Full Text Available Lead-free Ca, Zr co-doped BaTiO3 (BCZT single crystal with a dimension up to 2mm×2mm×2mm was grown by a spontaneous nucleation technique using KF as the flux. The composition of the studied single crystal was defined to be Ba0.798Ca0.202Zr0.006Ti0.994O3, corresponding to a tetragonal phase at room temperature. The oriented single crystal exhibited a quasi-static piezoelectric constant of approximately 232 pC/N. The effective piezoelectric coefficient d33* of the single domain crystal obtained under a unipolar electric field of 35 kV/cm was 179 pm/V. Rayleigh analysis was used to identify the intrinsic and extrinsic contributions to the room-temperature piezoelectricity of BCZT single crystal. The extrinsic contribution was estimated up to 40% due to the irreversible domain wall movement. Furthermore a sixth-order polynomial of Landau expansion was employed to analyze the intrinsic contribution to piezoelectricity of BCZT single crystal. The large energy barriers inhibited polarization rotations, leading to the relatively low piezoelectricity.

  6. Electric double layer transistors with ferroelectric BaTiO3 channels

    NARCIS (Netherlands)

    Ito, M.; Matsubara, Y.; Kozuka, Y.; Takahashi, K. S.; Kagawa, F.; Ye, J. T.; Iwasa, Y.; Ueno, K.; Tokura, Y.; Kawasaki, M.

    2014-01-01

    We report the surface conduction of a BaTiO3 thin film using electric double layer transistor (EDLT) structure. A transistor operation was observed at 220 K with an on/off ratio exceeding 10(5), demonstrating that ionic liquid gating is effective to induce carriers at the surface of ferroelectric

  7. Voltage effect in PTCR ceramics: Calculation by the method of tilted energy band

    International Nuclear Information System (INIS)

    Fang Chao; Zhou Dongxiang; Gong Shuping

    2010-01-01

    A numerical model for the calculation of the electrical characteristics of donor-doped BaTiO 3 semiconducting ceramics is suggested. This paper established a differential equation about electron level on the base of Poisson equation, and solved the equation with Runge-Kutta method. Under extra electric field, electrical characteristics have been calculated by the method of tilted energy band. We have quantitatively computed the positive temperature coefficient of resistivity (PTCR) behavior of donor-doped BaTiO 3 semiconducting ceramics and its voltage effect, and further obtained non-linear current-voltage characteristics with different grain sizes at different temperature. The results pointed out that the resistance jumping is reduced with increasing electric field applied; current and voltage relation follows Ohm's law below Curie temperature, and exhibits strong non-linear above Curie temperature; the non-linear coefficient shows a maximum value at temperature the resistivity reaches maximum and with grain size closed to depletion region width. The results are compared with experimental data.

  8. Surface structures and dielectric response of ultrafine BaTiO3 particles

    International Nuclear Information System (INIS)

    Jiang, B.; Peng, J.L.; Bursill, L.A.

    1998-01-01

    Characteristic differences are observed for the dielectric response and microstructures of BaTiO 3 nanoscale fine powders prepared using sol gel (SG) and steric acid gel (SAG) methods. The former exhibit a critical size below which there is no paraelectric/ferroelectric phase transition whereas BaTiO 3 prepared via the SAG route remained cubic for all conditions. Atomic resolution images of both varieties showed a high density of interesting surface steps and facets. Computer simulated images of surface structure models showed that the outer (100) surface was typically a BaO layer and that at corners and ledges the steps are typically finished with Ba+2 ions; i.e. the surfaces and steps are Ba-rich. Otherwise the surfaces were typically clean and free of amorphous layers. The relationship between the observed surfaces structures and theoretical models for size effects on the dielectric properties is discussed. (authors)

  9. A General Reliability Model for Ni-BaTiO3-Based Multilayer Ceramic Capacitors

    Science.gov (United States)

    Liu, Donhang

    2014-01-01

    The evaluation of multilayer ceramic capacitors (MLCCs) with Ni electrode and BaTiO3 dielectric material for potential space project applications requires an in-depth understanding of their reliability. A general reliability model for Ni-BaTiO3 MLCC is developed and discussed. The model consists of three parts: a statistical distribution; an acceleration function that describes how a capacitor's reliability life responds to the external stresses, and an empirical function that defines contribution of the structural and constructional characteristics of a multilayer capacitor device, such as the number of dielectric layers N, dielectric thickness d, average grain size, and capacitor chip size A. Application examples are also discussed based on the proposed reliability model for Ni-BaTiO3 MLCCs.

  10. Electrical transport across nanometric SrTiO3 and BaTiO3 barriers in conducting/insulator/conducting junctions

    Science.gov (United States)

    Navarro, H.; Sirena, M.; González Sutter, J.; Troiani, H. E.; del Corro, P. G.; Granell, P.; Golmar, F.; Haberkorn, N.

    2018-01-01

    We report the electrical transport properties of conducting/insulator/conducting heterostructures by studying current-voltage IV curves at room temperature. The measurements were obtained on tunnel junctions with different areas (900, 400 and 100 μm2) using a conducting atomic force microscope. Trilayers with GdBa2Cu3O7 (GBCO) as the bottom electrode, SrTiO3 or BaTiO3 (thicknesses between 1.6 and 4 nm) as the insulator barrier, and GBCO or Nb as the top electrode were grown by DC sputtering on (100) SrTiO3 substrates For SrTiO3 and BaTiO3 barriers, asymmetric IV curves at positive and negative polarization can be obtained using electrodes with different work function. In addition, hysteretic IV curves are obtained for BaTiO3 barriers, which can be ascribed to a combined effect of the FE reversal switching polarization and an oxygen vacancy migration. For GBCO/BaTiO3/GBCO heterostructures, the IV curves correspond to that expected for asymmetric interfaces, which indicates that the disorder affects differently the properties at the bottom and top interfaces. Our results show the role of the interface disorder on the electrical transport of conducting/insulator/conduction heterostructures, which is relevant for different applications, going from resistive switching memories (at room temperature) to Josephson junctions (at low temperatures).

  11. Preparation and electrical properties of (1 - x)Sr(Fe1/2Nb1/2)O3-xPbTiO3 ferroelectric ceramics

    International Nuclear Information System (INIS)

    Fang Bijun; Cheng Zhenquan; Sun Renbing; Ding Chenlu

    2009-01-01

    (1 - x)Sr(Fe 1/2 Nb 1/2 )O 3 -xPbTiO 3 (SFN-PT) ferroelectric ceramics were prepared by conventional solid-state reaction method via the wolframite precursor route. X-ray diffraction (XRD) measurement confirmed that the synthesized SFN-PT ceramics are of pure perovskite structure. With the increase of the concentration of PbTiO 3 (PT), crystal structure of the sintered SFN-PT ceramics changes from rhombohedral phase to tetragonal phase. Dielectric response of the SFN-PT ceramics changes from diffused and broad dielectric peaks to relatively sharp ones accompanied by the increase of the temperature of dielectric maximum (T m ). Small content of MnO 2 or Li 2 CO 3 doping can greatly decrease the dielectric loss of the SFN-PT ceramics, furthermore, the abnormal increase of dielectric constant and loss tangent in the paraelectric phase is suppressed accordingly. Typical P-E hysteresis loops are observed in the SFN-PT ceramics, however, the saturate polarization (P s ) is small. MnO 2 or Li 2 CO 3 doping can greatly decrease the coercive field (E c ) of the SFN-PT ceramics accompanied by large increase of P s . Piezoelectric constant d 33 of the SFN-PT ceramics is small except for SFN30-PT70 ceramics, which reaches 22pC/N

  12. Electrical Conduction of Ba(Ti0.99Fe0.01)O3Ceramic at High Temperatures

    Science.gov (United States)

    Yu, Zi-De; Chen, Xiao-Ming

    2018-03-01

    BaTiO3 and Ba(Ti0.99Fe0.01)O3ceramics with dense microstructure have been synthesized by a solid-state reaction method, and their electrical conduction investigated by broadband electrical impedance spectroscopy at frequencies from 0.05 Hz to 3 × 106 Hz and temperatures from 200°C to 400°C. Compared with BaTiO3, the real part of the permittivity and the phase-transition temperature of Ba(Ti0.99Fe0.01)O3-δ decreased. Relaxation peaks appeared in the curves of the imaginary part of the permittivity as a function of frequency. With increase in frequency, the peaks gradually shifted towards higher frequency and their height increased. Conductivity was closely related to frequency and temperature. Frequency-dependent conductivity was analyzed using the Jonscher double power law. Compared with BaTO3, Ba(Ti0.99Fe0.01)O3-δ exhibited high impedance at given frequency and temperature. Impedance Cole-Cole plots displayed two semicircles, which could be well fit using two parallel RC equivalent circuit models. The conductivity activation energy was found to be around 1 eV. For Ba(Ti0.99Fe0.01)O3-δ , the electrical modulus curve versus frequency displayed two peaks.

  13. Preparation and characterization of self-assembled percolative BaTiO3–CoFe2O4 nanocomposites via magnetron co-sputtering

    Directory of Open Access Journals (Sweden)

    Qian Yang

    2014-04-01

    Full Text Available BaTiO3–CoFe2O4 composite films were prepared on (100 SrTiO3 substrates by using a radio-frequency magnetron co-sputtering method at 750 °C. These films contained highly (001-oriented crystalline phases of perovskite BaTiO3 and spinel CoFe2O4, which can form a self-assembled nanostructure with BaTiO3 well-dispersed into CoFe2O4 under optimized sputtering conditions. A prominent dielectric percolation behavior was observed in the self-assembled nanocomposite. Compared with pure BaTiO3 films sputtered under similar conditions, the nanocomposite film showed higher dielectric constants and lower dielectric losses together with a dramatically suppressed frequency dispersion. This dielectric percolation phenomenon can be explained by the 'micro-capacitor' model, which was supported by measurement results of the electric polarization and leakage current.

  14. Aggregate linear properties of ferroelectric ceramics and polycrystalline thin films: Calculation by the method of effective piezoelectric medium

    Science.gov (United States)

    Pertsev, N. A.; Zembilgotov, A. G.; Waser, R.

    1998-08-01

    The effective dielectric, piezoelectric, and elastic constants of polycrystalline ferroelectric materials are calculated from single-crystal data by an advanced method of effective medium, which takes into account the piezoelectric interactions between grains in full measure. For bulk BaTiO3 and PbTiO3 polarized ceramics, the dependences of material constants on the remanent polarization are reported. Dielectric and elastic constants are computed also for unpolarized c- and a-textured ferroelectric thin films deposited on cubic or amorphous substrates. It is found that the dielectric properties of BaTiO3 and PbTiO3 polycrystalline thin films strongly depend on the type of crystal texture. The influence of two-dimensional clamping by the substrate on the dielectric and piezoelectric responses of polarized films is described quantitatively and shown to be especially important for the piezoelectric charge coefficient of BaTiO3 films.

  15. Ceramic superconductors II

    International Nuclear Information System (INIS)

    Yan, M.F.

    1988-01-01

    This volume compiles papers on ceramic superconductors. Topics include: structural patterns in High-Tc superconductors, phase equilibria of barium oxide superconductors, localized electrons in tetragonal YBa/sub 2/Cu/sub 3/O/sub 7-δ/, lattice and defect structure and properties of rare earth/alkaline earth-copper-oxide superconductors, alternate candidates for High-Tc superconductors, perovskite-structure superconductors; superconductive thin film fabrication, and superconductor/polymer composites

  16. Dependence of e31,f on polar axis texture for tetragonal Pb(Zrx,Ti1-x)O3 thin films

    Science.gov (United States)

    Yeager, Charles B.; Ehara, Yoshitaka; Oshima, Naoya; Funakubo, Hiroshi; Trolier-McKinstry, Susan

    2014-09-01

    It was shown by Ouyang et al. [Appl. Phys. Lett. 86, 152901 (2005)] that the piezoelectric e31,f coefficient is largest parallel to the spontaneous polarization in tetragonal PbZrxTi1-xO3 (PZT) films. However, the expected piezoelectric data are typically calculated from phenomenological constants derived from data on ceramic PZT. In this work, the dependence of e31,f on c-axis texture fraction, f001, for {001}PZT thin films was measured by growing films with systematically changed f001 using CaF2, MgO, SrTiO3, and Si substrates. An approximately linear increase in e31,f with f001 was observed for compositions up to 43 mol. % Zr, and 100% c-domain properties were extrapolated. It was demonstrated that c-axis PZT films can achieve e31,f exceeding -12 C/m2 for many tetragonal compositions. The energy harvesting figure of merit, e31,f2/ɛr, for c-axis PZT films surpassed 0.8 C2/m4. This is larger than the figure of merit of gradient-free PZT films grown on Si substrates by a factor of four.

  17. Effect of cooling rate on tetragonal to monoclinic transformation in hot pressed ZrO2(Y2O3) ceramics

    International Nuclear Information System (INIS)

    Zhu, W.Z.; Ding, Z.S.; Lei, T.C.; Zhou, Y.

    1995-01-01

    It is well documented that the tetragonal (T) to monoclinic (M) transition in either pure zirconia or partially stabilized zirconia is the origin of toughening in that resistance to the propagation of cracks can be greatly enhanced by the concurrent appearance of the stress field of the transformation. In the present paper, the effect of cooling rate on the T → M phase transformation in yttria-containing zirconia and its resultant mechanical properties have been studied by means of thermal expansion analysis. Both the T → M and M → T transformations are affected by the cooling and heating rates, respectively. The amount of M-phase decreases with increasing cooling rate. T → M transition occurring within the interior part of specimen can be completely inhibited by the cooling rate of 100 C/min for ZrO 2 (2mol% Y 2 O 3 ) ceramic sintered at 1,600 C. The start point and end point of the T → M transformation decreases and increases, respectively, with increasing cooling rate. Both the start point and end point of the M → T transformation increase with increasing cooling rate. The divergence between the results of X-ray diffraction and the thermal expansion analysis has been rationalized in terms of the both internal and external factors, namely, preferential sites of surface for the formation of the M-phase and limited sensitivity of measurement of the thermal expansion apparatus. Both the water-cooled and air-cooled specimens show much improved mechanical properties regardless of the sintering temperatures or yttria content because of the relatively higher T-phase fraction retained to room temperature

  18. Controlled Confinement of Half-metallic 2D Electron Gas in BaTiO3/Ba2FeReO6/BaTiO3 Heterostructures: A First-principles Study

    Science.gov (United States)

    Saha-Dasgupta, Tanusri; Baidya, Santu; Waghmare, Umesh; Paramekanti, Arun

    Using density functional theory calculations, we establish that the half-metallicity of bulk Ba2FeReO6 survives down i to 1 nm thickness in BaTiO3/Ba2FeReO6/BaTiO3 heterostructures grown along the (001) and (111) directions. The confinement of the two-dimensional (2D) electron gas in this quantum well structure arises from the suppressed hybridization between Re/Fe d states and unoccupied Ti d states, and it is further strengthened by polar fields for the (111) direction. This mechanism, distinct from the polar catastrophe, leads to an order of magnitude stronger confinement of the 2D electron gas than that at the LaAlO3/SrTiO3 interface. We further show low-energy bands of (111) heterostructure display nontrivial topological character. Our work opens up the possibility of realizing ultra-thin spintronic devices. Journal Ref: Phys. Rev. B 92, 161106(R) (2015) S.B. and T.S.D thank Department of Science and Technology, India for the support through Thematic Unit of Excellence. AP was supported by NSERC (Canada).

  19. Displacive Transformation in Ceramics

    Science.gov (United States)

    1994-02-28

    PZT ), ceramics have attracted natural abundance. much attention for use in nonvolatile semiconductor mem- We attribute the observed spectra in Fig. I to...near a crack tip in piezoelectric ceramics of lead zirconate titanate ( PZT ) and barium titanate. They reasoned that the poling of ferroelectric... Texture in Ferroelastic Tetragonal Zirconia," J. Am. Ceram . Soc., 73 (1990) no. 6: 1777-1779. 27. J. F. Jue and A. Virkar, "Fabrication, Microstructural

  20. Nitrogen induced ferromagnetism in Cobalt doped BaTiO3

    Directory of Open Access Journals (Sweden)

    Chandrima Mitra

    2012-09-01

    Full Text Available The electronic structure and magnetism of Cobalt doped BaTiO3 (BaTi1−xCoxO3 is investigated. Substitutional Nitrogen on an Oxygen site is found to play an important role in inducing net magnetic moments in the system. The presence of a Nitrogen atom as nearest neighbour to a Cobalt atom is crucial in producing spin splitting of both the Nitrogen and Cobalt states thereby introducing a net local magnetic moment. The introduction of Nitrogen is further found to enhance ferromagnetic interactions between Cobalt atoms.

  1. Microstructure Control of Barium Titanate Grain-oriented Ceramics and Their Piezoelectric Properties

    International Nuclear Information System (INIS)

    Mori, Rintaro; Nakashima, Koichi; Fujii, Ichiro; Wada, Satoshi; Hayashi, Hiroshi; Nagamori, Yoshitaka; Yamamoto, Yuichi

    2011-01-01

    The Barium titanate (BaTiO 3 , BT) [110] grain-oriented ceramics along [110] direction were prepared by a templated grain growth (TGG) method. The [110] oriented BT platelike particles (t-BT) were used as template particles. The relationship between poling treatment program and piezoelectric constant was investigated. The change in the poling conditions did not greatly influence domain size and the piezoelectric constant. The relationship between piezoelectric properties and domain size in BT grain-oriented ceramics was investigated. The smaller domain size was required to increase the piezoelectric constant.

  2. Size effect in barium titanate powders synthesized by different hydrothermal methods

    International Nuclear Information System (INIS)

    Sun Weian

    2006-01-01

    The size effect in barium titanate (BaTiO 3 ) was investigated both experimentally and theoretically. Tetragonal BaTiO 3 powders with average sizes from 80 to 420 nm were directly prepared by different hydrothermal methods. The tetragonality of the hydrothermal BaTiO 3 decreased with decreasing particle size, which exhibited a dependence on the synthesis method. A phenomenological model for the size effect was proposed to interpret the experimental observations. The influence of the defects, mainly the lattice hydroxyl, on the size effect was investigated to understand the correlation between the size effect and synthesis condition. The permittivities of BaTiO 3 powder at different particle sizes were calculated, which predicted a maximum permittivity of over 16 000 around the room-temperature critical size of ∼70 nm. The prediction was in good accordance with the experimental data reported recently

  3. First-principles calculations on thermodynamic properties of BaTiO3 rhombohedral phase.

    Science.gov (United States)

    Bandura, Andrei V; Evarestov, Robert A

    2012-07-05

    The calculations based on the linear combination of atomic orbitals have been performed for the low-temperature phase of BaTiO(3) crystal. Structural and electronic properties, as well as phonon frequencies were obtained using hybrid PBE0 exchange-correlation functional. The calculated frequencies and total energies at different volumes have been used to determine the equation of state and thermal contribution to the Helmholtz free energy within the quasiharmonic approximation. For the first time, the bulk modulus, volume thermal expansion coefficient, heat capacity, and Grüneisen parameters in BaTiO(3) rhombohedral phase have been estimated at zero pressure and temperatures form 0 to 200 K, based on the results of first-principles calculations. Empirical equation has been proposed to reproduce the temperature dependence of the calculated quantities. The agreement between the theoretical and experimental thermodynamic properties was found to be satisfactory. Copyright © 2012 Wiley Periodicals, Inc.

  4. Improving dielectric properties of BaTiO_3/poly(vinylidene fluoride) composites by employing core-shell structured BaTiO_3@Poly(methylmethacrylate) and BaTiO_3@Poly(trifluoroethyl methacrylate) nanoparticles

    International Nuclear Information System (INIS)

    Zhang, Xianhong; Zhao, Sidi; Wang, Fang; Ma, Yuhong; Wang, Li; Chen, Dong; Zhao, Changwen; Yang, Wantai

    2017-01-01

    Highlights: • Core-shell structured BT@PMMA and BT@PTFEMA nanoparticles were synthesized. • The dispersity of BT nanoparticles in PVDF matrix was improved significantly. • Dielectric properties both of BT@PMMA/PVDF and BT@PTFEMA/PVDF composites were improved. • The frequency dependence of dielectric constant attenuation of BT@PTFEMA/PVDF composites was smaller than that of BT@PMMA/PVDF composites. - Abstract: Polymer based dielectric composites were fabricated through incorporation of core-shell structured BaTiO_3 (BT) nanoparticles into PVDF matrix by means of solution blending. Core-shell structured BT nanoparticles with different shell composition and shell thickness were prepared by grafting methacrylate monomer (MMA or TFEMA) onto the surface of BT nanoparticles via surface initiated atom transfer radical polymerization (SI-ATRP). The content of the grafted polymer and the micro-morphology of the core-shell structured BT nanoparticles were investigated by thermo gravimetric analyses (TGA) and transmission electron microscopy (TEM), respectively. The dielectric properties were measured by broadband dielectric spectroscopy. The results showed that high dielectric constant and low dielectric loss are successfully realized in the polymer based composites. Moreover, the type of the grafted polymer and its content had different effect on the dielectric constant. In detail, the attenuation of dielectric constant was 16.6% for BT@PMMA1/PVDF and 10.7% for BT@PMMA2/PVDF composite in the range of 10 Hz to 100 kHz, in which the grafted content of PMMA was 5.5% and 8.0%, respectively. However, the attenuation of dielectric constant was 5.5% for BT@PTFEMA1/PVDF and 4.0% for BT@PTFEMA2/PVDF composite, in which the grafted content of PTFEMA was 1.5% and 2.0%, respectively. These attractive features of BT@PTFEMA/PVDF composites suggested that dielectric ceramic fillers modified with fluorinated polymer can be used to prepare high performance composites, especially

  5. Superplastic ceramics and intermetallics and their potential applications

    International Nuclear Information System (INIS)

    Wadsworth, J.; Nieh, T.G.

    1994-11-01

    Recent advances in the basic understanding of superplasticity and superplastic forming of ceramics and intermetallics are reviewed. Fine-grained superplastic ceramics, including yttria-stabilized tetragonal zirconia polycrystal, Y- or MgO-doped Al 2 O 3 Hydroxyapatite, β-spodumene glass ceramics, Al 2 0 3 -YTZP two-phase composites, SiC-Si 3 N 4 and Fe-Fe 3 C composites, are discussed. Superplasticity in the nickel-base (e.g., Ni 3 Al and Ni 3 Si) and titanium-base intermetallics (TiAl and T1 3 Al), is described. Deformation mechanisms as well as microstructural requirements and effects such as grain size, grain growth, and grain-boundary phases, on the superplastic deformation behavior am addressed. Factors that control the superplastic tensile elongation of ceramics are discussed. Superplastic forming, and particularly biaxial gas-pressure forming, of several ceramics and intermetallics are presented with comments on the likelihood of commercial application

  6. Enhanced piezoelectricity in (1 -x)Bi1.05Fe1-yAyO3-xBaTiO3 lead-free ceramics: site engineering and wide phase boundary region.

    Science.gov (United States)

    Zheng, Ting; Jiang, Zhenggen; Wu, Jiagang

    2016-07-28

    Site engineering has been employed to modulate the piezoelectric activity of high temperature (1 -x)Bi1.05Fe1-yScyO3-xBaTiO3 lead-free ceramics fabricated by a conventional solid-state method together with a quenching technique. The effects of x and y content on the phase structure, microstructure, and electrical properties have been investigated in detail. A wide rhombohedral (R) to pseudo-cubic (C) phase boundary was formed in the ceramics with x = 0.30 and 0 ≤y≤ 0.07, thus leading to enhanced piezoelectricity (d33 = 120-180 pC N(-1)), ferroelectricity (Pr = 19-22 μC cm(-2)) and a high Curie temperature (TC = 478-520 °C). In addition, the influence of different element substitutions for Fe(3+) on phase structure and electrical behavior was also investigated. Improved piezoelectricity (d33 = 160-180 pC N(-1)) and saturated P-E loops can be simultaneously achieved in the ceramics with A = Sc, Ga, and Al due to the R-C phase boundary. As a result, site engineering may be an efficient way to modulate the piezoelectricity of BiFeO3-BaTiO3 lead-free ceramics.

  7. Current status and future aspects of R&D activities on electro- ceramic components in Japanese industry

    Science.gov (United States)

    Takagi, Hiroshi

    2011-05-01

    The oldest pottery in Japan was made 16,500 years ago in Jomon period. On the background of a long history of Japanese ceramics, Murata and other Japanese manufacturers have been developing electro-ceramic materials and manufacturing many kinds of electronic components using them. In 1937, TDK manufactured ferrite cores first in the world. Then, Japanese electro-ceramic industry has led the world on electro-ceramic materials and components until now, especially in the fields of BaTiO3, PZT, PTC thermistor, ZnO varistor and insulating ceramics. From the analysis of the papers reported lately, R&D activities of Japanese manufacturers are understood to cover not only improving properties of electro-ceramics, but also appropriate technologies and basic technologies.

  8. Tetragonal BiFeO3 on yttria-stabilized zirconia

    International Nuclear Information System (INIS)

    Liu, Heng-Jui; Du, Yu-Hao; Gao, Peng; Ikuhara, Yuichi; Huang, Yen-Chin; Chen, Yi-Chun; Chen, Hsiao-Wen; Liu, Hsiang-Lin; He, Qing; Chu, Ying-Hao

    2015-01-01

    High structural susceptibility of multiferroic BiFeO 3 (BFO) makes it a potential replacement of current Pb-based piezoelectrics. In this study, a tetragonal phase is identified based on a combination of x-ray diffraction, scanning transmission electronic microscopy, x-ray absorption spectroscopy, and Raman spectroscopy when BFO is grown on yttria-stabilized zirconia (YSZ) substrates. To distinguish the discrepancy between this tetragonal phase and common cases of monoclinic BFO, piezoelectric force microscopy images and optical property are also performed. It shows a lower electrostatic energy of ferroelectric domains and a large reduction of band gap for BFO grown on YSZ substrate comparing to the well-known one grown on LaAlO 3 substrate. Our findings in this work can provide more insights to understand the structural diversity of multiferroic BFO system for further applications

  9. Adaptive ferroelectric state at morphotropic phase boundary: Coexisting tetragonal and rhombohedral phases

    International Nuclear Information System (INIS)

    Zhang, Yang; Xue, Dezhen; Wu, Haijun; Ding, Xiangdong; Lookman, Turab; Ren, Xiaobing

    2014-01-01

    With a focus on local symmetry, the microstructural basis for high piezoelectric performance in PbMg 1/3 Nb 2/3 O 3 –xPbTiO 3 (PMN–PT) ceramics at the morphotropic phase boundary (MPB) composition was investigated by means of convergent-beam electron diffraction analysis and twin diffraction pattern analysis. The local structure was found to consist of coexisting (1 0 1)-type tetragonal nanotwins and (0 0 1)-type rhombohedral nanotwins. A phenomenological theory based on crystallography is proposed to show that such nanoscale coexistence can give rise to an average monoclinic structure through strain accommodation. The average monoclinic structures (Ma and Mc) vary with temperature and composition due to the dependence on temperature and composition of the lattice parameters. Based on in situ X-ray diffraction data, we demonstrate how the polarization rotates across the MPB region in PMN–PT ceramics with varying temperatures and compositions

  10. Electro-optical properties of tetragonal KNbO 3

    Indian Academy of Sciences (India)

    Linear electro-optical tensor coefficients and optical susceptibility of tetragonal KNbO3 are calculated using a formalism based on bond charge theory. Results are in close agreement with the experimental data. The covalent Nb–O bonding network comprising the distorted NbO6 octahedral groups in the structure is found to ...

  11. Forming of superplastic ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Lesuer, D.R.; Wadsworth, J.; Nieh, T.G.

    1994-05-01

    Superplasticity in ceramics has now advanced to the stage that technologically viable superplastic deformation processing can be performed. In this paper, examples of superplastic forming and diffusion bonding of ceramic components are given. Recent work in biaxial gas-pressure forming of several ceramics is provided. These include yttria-stabilized, tetragonal zirconia (YTZP), a 20% alumina/YTZP composite, and silicon. In addition, the concurrent superplastic forming and diffusion bonding of a hybrid ceramic-metal structure are presented. These forming processes offer technological advantages of greater dimensional control and increased variety and complexity of shapes than is possible with conventional ceramic shaping technology.

  12. Calcul théorique de l’hystérésis thermique de BaTiO3 pur et dopé au fer

    NARCIS (Netherlands)

    Aattar, M.; Khatib, D.; Noheda, B.

    1999-01-01

    Theory of thermal hysteresis of pure and iron doped BaTiO3. The value of the thermal hysteresis of pure and iron doped BaTiO3 was calculated using an effective field model taking into account dipolar and quadripolar interactions. The calculation is performed using a self-consistent method. The

  13. Influence of rare-earth addition on microstructure and dielectric behavior of Ba0.6Sr0.4TiO3 ceramics

    International Nuclear Information System (INIS)

    Zhang Jingji; Zhai Jiwei; Chou Xiujian; Yao Xi

    2008-01-01

    Ba 0.6 Sr 0.4 TiO 3 (BST) ceramics with 0.5 mol% various trivalent rare-earth additions prepared by a solid-state route are investigated. A strong correlation is observed between the microstructure, dielectric properties and rare-earth element dopant. The results display that comparing with the lattice constants of undoped and doped rare-earth BST, the structure transforms from cubic to tetragonal structure. In addition, the dopant improves the tetragonal distortion with the ionic radius of rare earth decreasing, and then deteriorates it with further decreasing. Large ions rare-earth additions effectively suppress the grain growth of BST. It is found that the temperature-permittivity characteristics for the BSTR (R, namely, rare earth) system could be controlled using various rare-earth elements. Especially, such as Sm, Eu, Gd dopants are effective to satisfy the tunable microwave devices application due to the decrease of permittivity and the improvement of dissipation factors of BST ceramic with the accompanying high-tunability

  14. Synthesis, microstructure and mechanical properties of ceria stabilized tetragonal zirconia prepared by spray drying technique

    International Nuclear Information System (INIS)

    Sharma, S.C.; Gokhale, N.M.; Dayal, Rajiv; Lazl, Ramji

    2002-01-01

    Ceria stabilized zirconia powders with ceria concentration varying from 6 to 16 mol% were synthesized using spray drying technique. Powders were characterized for their particle size distribution and specific surface area. The dense sintered ceramics fabricated using these powders were characterized for their microstructure, crystallite size and phase composition. The flexural strength, fracture toughness and micro-hardness of sintered ceramics were measured. High fracture toughness and flexural strength were obtained for sintered bodies with 12 mol% of CeO 2 . Flexural strength and fracture toughness were dependent on CeO 2 concentration, crystallite size and phase composition of sintered bodies. Correlation of data has indicated that the transformable tetragonal phase is the key factor in controlling the fracture toughness and strength of ceramics. It has been demonstrated that the synthesis method is effective to prepare nanocrystalline tetragonal ceria stabilized zirconia powders with improved mechanical properties. Ce-ZrO 2 with 20 wt% alumina was also prepared with flexural strength, 1200 MPa and fracture toughness 9.2 MPa√m. (author)

  15. Inclusion-initiated fracture model for ceramics

    International Nuclear Information System (INIS)

    Sung, J.; Nicholson, P.S.

    1990-01-01

    The fracture of ceramics initiating from a typical inclusion is analyzed. The inclusion is considered to have a thermal expansion coefficient and fracture toughness lower than those of the matrix and a Young's modulus higher than that of the matrix. Inclusion-initiated fracture is modeled for a spherical inclusion using a weight function method to compute the residual stress intensity factor for a part-through elliptical crack. The results are applied to an α-Al 2 O 3 inclusion embedded in a tetragonal ZrO 2 ceramic. The strength predictions agree well with experimental data

  16. Giant strain with ultra-low hysteresis and high temperature stability in grain oriented lead-free K0.5Bi0.5TiO3-BaTiO3-Na0.5Bi0.5TiO3 piezoelectric materials.

    Science.gov (United States)

    Maurya, Deepam; Zhou, Yuan; Wang, Yaojin; Yan, Yongke; Li, Jiefang; Viehland, Dwight; Priya, Shashank

    2015-02-26

    We synthesized grain-oriented lead-free piezoelectric materials in (K0.5Bi0.5TiO3-BaTiO3-xNa0.5Bi0.5TiO3 (KBT-BT-NBT) system with high degree of texturing along the [001]c (c-cubic) crystallographic orientation. We demonstrate giant field induced strain (~0.48%) with an ultra-low hysteresis along with enhanced piezoelectric response (d33 ~ 190pC/N) and high temperature stability (~160°C). Transmission electron microscopy (TEM) and piezoresponse force microscopy (PFM) results demonstrate smaller size highly ordered domain structure in grain-oriented specimen relative to the conventional polycrystalline ceramics. The grain oriented specimens exhibited a high degree of non-180° domain switching, in comparison to the randomly axed ones. These results indicate the effective solution to the lead-free piezoelectric materials.

  17. Local manifestations of a static magnetoelectric effect in nanostructured BaTiO3-BaFe12O9 composite multiferroics

    Science.gov (United States)

    Trivedi, Harsh; Shvartsman, Vladimir V.; Lupascu, Doru C.; Medeiros, Marco S. A.; Pullar, Robert C.; Kholkin, Andrei L.; Zelenovskiy, Pavel; Sosnovskikh, Andrey; Shur, Vladimir Ya.

    2015-02-01

    A study on magnetoelectric phenomena in the barium titanate-barium hexaferrite (BaTiO3-BaFe12O19) composite system, using high resolution techniques including switching spectroscopy piezoresponse force microscopy (SSPFM) and spatially resolved confocal Raman microscopy (CRM), is presented. It is found that both the local piezoelectric coefficient and polarization switching parameters change on the application of an external magnetic field. The latter effect is rationalized by the influence of magnetostrictive stress on the domain dynamics. Processing of the Raman spectral data using principal component analysis (PCA) and self-modelling curve resolution (SMCR) allowed us to achieve high resolution phase distribution maps along with separation of average and localized spectral components. A significant effect of the magnetic field on the Raman spectra of the BaTiO3 phase has been revealed. The observed changes are comparable with the classical pressure dependent studies on BaTiO3, confirming the strain mediated character of the magnetoelectric coupling in the studied composites.

  18. Superplasticity in Fine-Grained Ceramics

    Science.gov (United States)

    1994-01-31

    Stabilized, Tetragonal Zirconia," Acta Metall. Mater., 39(12), (1991), pp. 3227-3236. 10. B. Kellett, P. Carry, and A. Mocellin , "Extrusion of Tet-ZrO2...F. Wakai, S. Sakaguchi, and H. Kato, J. Ceram. Soc. Jap., 94, 72 (1986). 8. B. Kellett, P. Carry, and A. Mocellin , J. Amer. Ceram. Soc., 74, 1922

  19. Texturing of sodium bismuth titanate-barium titanate ceramics by templated grain growth

    Science.gov (United States)

    Yilmaz, Huseyin

    2002-01-01

    Sodium bismuth titanate modified with barium titanate, (Na1/2Bi 1/2)TiO3-BaTiO3 (NBT-BT), is a candidate lead-free piezoelectric material which has been shown to have comparatively high piezoelectric response. In this work, textured (Na1/2Bi1/2)TiO 3-BaTiO3 (5.5mol% BaTiO3) ceramics with pc (where pc denotes the pseudocubic perovskite cell) orientation were fabricated by Templated Grain Growth (TGG) or Reactive Templated Grain Growth (RTGG) using anisotropically shaped template particles. In the case of TGG, molten salt synthesized SrTiO3 platelets were tape cast with a (Na1/2Bi1/2)TiO3-5.5mol%BaTiO3 powder and sintered at 1200°C for up to 12 hours. For the RTGG approach, Bi4Ti3O12 (BiT) platelets were tape cast with a Na2CO3, Bi2O3, TiO 2, and BaCO3 powder mixture and reactively sintered. The TGG approach using SrTiO3 templates gave stronger texture along [001] compared to the RTGG approach using BiT templates. The textured ceramics were characterized by X-ray and electron backscatter diffraction for the quality of texture. The texture function was quantified by the Lotgering factor, rocking curve, pole figures, inverse pole figures, and orientation imaging microscopy. Electrical and electromechanical property characterization of randomly oriented and pc textured (Na1/2Bi1/2)TiO 3-5.5 mol% BaTiO3 rhombohedral ceramics showed 0.26% strain at 70 kV/cm, d33 coefficients over 500 pC/N have been obtained for highly textured samples (f ˜ 90%). The piezoelectric coefficient from Berlincourt was d33 ˜ 200 pC/N. The materials show considerable hysteresis. The presence of hysteresis in the unipolar-electric field curve is probably linked to the ferroelastic phase transition seen in the (Na 1/2Bi1/2)TiO3 system on cooling from high temperature at ˜520°C. The macroscopic physical properties (remanent polarization, dielectric constant, and piezoelectric coefficient) of random and textured ([001] pc) rhombohedral perovskites were estimated by linear averaging of single

  20. Variable-temperature single-crystal X-ray diffraction study of tetragonal and cubic perovskite-type barium titanate phases.

    Science.gov (United States)

    Nakatani, Tomotaka; Yoshiasa, Akira; Nakatsuka, Akihiko; Hiratoko, Tatsuya; Mashimo, Tsutomu; Okube, Maki; Sasaki, Satoshi

    2016-02-01

    A variable-temperature single-crystal X-ray diffraction study of a synthetic BaTiO3 perovskite has been performed over the temperature range 298-778 K. A transition from a tetragonal (P4mm) to a cubic (Pm3m) phase has been revealed near 413 K. In the non-centrosymmetric P4mm symmetry group, both Ti and O atoms are displaced along the c-axis in opposite directions with regard to the Ba position fixed at the origin, so that Ti(4+) and Ba(2+) cations occupy off-center positions in the TiO6 and BaO12 polyhedra, respectively. Smooth temperature-dependent changes of the atomic coordinates become discontinuous with the phase transition. Our observations imply that the cations remain off-center even in the high-temperature cubic phase. The temperature dependence of the mean-square displacements of Ti in the cubic phase includes a significant static component which means that Ti atoms are statistically distributed in the off-center positions.

  1. Preparation and electrical properties of (1 - x)Sr(Fe{sub 1/2}Nb{sub 1/2})O{sub 3}-xPbTiO{sub 3} ferroelectric ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Fang Bijun [School of Materials Science and Engineering, Jiangsu Polytechnic University, Changzhou, Jiangsu 213164 (China)], E-mail: fangbj@em.jpu.edu.cn; Cheng Zhenquan; Sun Renbing; Ding Chenlu [School of Materials Science and Engineering, Jiangsu Polytechnic University, Changzhou, Jiangsu 213164 (China)

    2009-03-05

    (1 - x)Sr(Fe{sub 1/2}Nb{sub 1/2})O{sub 3}-xPbTiO{sub 3} (SFN-PT) ferroelectric ceramics were prepared by conventional solid-state reaction method via the wolframite precursor route. X-ray diffraction (XRD) measurement confirmed that the synthesized SFN-PT ceramics are of pure perovskite structure. With the increase of the concentration of PbTiO{sub 3} (PT), crystal structure of the sintered SFN-PT ceramics changes from rhombohedral phase to tetragonal phase. Dielectric response of the SFN-PT ceramics changes from diffused and broad dielectric peaks to relatively sharp ones accompanied by the increase of the temperature of dielectric maximum (T{sub m}). Small content of MnO{sub 2} or Li{sub 2}CO{sub 3} doping can greatly decrease the dielectric loss of the SFN-PT ceramics, furthermore, the abnormal increase of dielectric constant and loss tangent in the paraelectric phase is suppressed accordingly. Typical P-E hysteresis loops are observed in the SFN-PT ceramics, however, the saturate polarization (P{sub s}) is small. MnO{sub 2} or Li{sub 2}CO{sub 3} doping can greatly decrease the coercive field (E{sub c}) of the SFN-PT ceramics accompanied by large increase of P{sub s}. Piezoelectric constant d{sub 33} of the SFN-PT ceramics is small except for SFN30-PT70 ceramics, which reaches 22pC/N.

  2. Synthesis of BaTiO3 and SrTiO3 by microwave assisted hydrothermal method (MAH) using anatase as titanium precursor

    International Nuclear Information System (INIS)

    Magalhães, Renata da Silva; Macedo Junior, Wagner Dias; Souza, Agda Eunice de; Teixeira, Silvio Rainho; Li, Maximo Siu; Longo, Elson

    2016-01-01

    Full text: Strontium and barium titanates (SrTiO 3 (ST) and BaTiO 3 (BT)) in their crystalline form belong to the perovskite (ABO 3 ) class. Both display a semiconductor behavior with many interesting properties. The method of synthesis employed and different precursors may influence the morphology and properties of ceramic materials [1,2]. Barium (BT) and strontium (St) titanates were produced using the Microwave Assisted Hydrothermal Method (MAH), different concentrations (1,3 and 6 molL -1 ) of mineralizer (KOH) and a different titanium precursor: a complex anatase-hydrogen peroxide. Barium and strontium chloride were used as the other metal precursors. The resulting material were characterized by different techniques such as: X-ray diffraction (XRD), Micro-Raman Spectroscopy (MR), UV-Vis, Scanning Electron microscopy (SEM) and finally their photoluminescent emissions (FL) were recorded at room temperature. The results show that there were differences in crystallinity, morphology, number of formed phases and photoluminescent emission, among the titanate produced with different concentrations of mineralizer. References: [1] A.E. Souza et al., Order–disorder degree of self-assembled clusters: Influence on photoluminescence emission and morphology of Ba x Sr 1-x TiO 3 nanocrystals, Chemical Physics Letters 514 (2011) 301–306. [2] T. M. Mazzo et al., Influence of titanium precursor on photoluminescent emission of micro-cube-shaped CaTiO 3 , Journal of Luminescence 165 (2015). (author)

  3. Investigation of structural and electrical properties of (1 - x) Bi0.5Mg0.5TiO3-(x) PbTiO3 ceramic system

    International Nuclear Information System (INIS)

    Rai, Radheshyam; Sinha, Abinhav; Sharmac, Seema; Sinha, N.K.P.

    2009-01-01

    [(BiMg 0.5 Ti 0.5 O 3 ) 1-x ][PbTiO 3 ] x (BMT-PT) ceramic powders of different compositions were prepared by solid-state reaction method. X-ray diffraction analysis of the compounds suggest the structural change (rhombohedral to tetragonal) in these ceramics. SEM photographs exhibit the uniform distribution of grains with less porosity. Polarization vs. electric field (P-E) studies show maximum remanent polarization (P r ∼ 7.9 μC/cm 2 ) for composition x = 0.34. The dielectric peaks were found to be broadened that indicates the existence of diffuse phase transition. Diffusivity (γ) study of phase transition in these compounds provided values between 1 and 2 indicating the variation of degree of disorderness in the system.

  4. Relaxor behavior in lead-free Ba(Ti1−xScx/2Nbx/2O3 ceramics

    Directory of Open Access Journals (Sweden)

    N. Bensemma

    2014-06-01

    Full Text Available Solid solutions of (1−xBaTiO3-xBaSc1/2Nb1/2O3 (BT-BSN with x = 0.025, 0.05, 0.075, 0.1 and 0.125 were prepared by a high temperature solid-state reaction technique. The effects of the Ba(Sc1/2Nb1/2O3 addition on the phase composition, dielectric properties, as well as polarization-electric field (P-E loops of the BT-BSN solid solution were investigated. The room-temperature X-ray diffraction analyses of all the ceramics revealed a perovskite phase after sintering at 1350 °C with a composition-dependent symmetry. Temperature and frequency dependence of the dielectric permittivity and losses have been explored: ceramics of compositions x ≤ 0.075 showed normal ferroelectric behavior, while ceramics with x ≥ 0.1 were of relaxor type. The degree of diffuseness and the relaxor effect increase while the transition temperature (TC or Tm decreases when both scandium and niobium are introduced in the BaTiO3 lattice. Ceramics of composition x = 0.125 exhibited interesting relaxor characteristics at 10 kHz: ΔTm = 20 K, ɛr = 12,000, and Tm = 140 K. In addition, modeled using Vogel–Fülcher relation, this same composition showed the fitting parameters: Ea = 0.0503 eV, f0 = 1.129 × 1014 Hz and TVF = 166.85 K.

  5. Tetragonal BiFeO{sub 3} on yttria-stabilized zirconia

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Heng-Jui [Department of Materials Science Engineering, National Chiao Tung University, Hsinchu 30010, Taiwan (China); Department of Physics, National Taiwan Normal University, Taipei 11677, Taiwan (China); Du, Yu-Hao [Department of Materials Science Engineering, National Chiao Tung University, Hsinchu 30010, Taiwan (China); Gao, Peng; Ikuhara, Yuichi [Institute of Engineering Innovation, The University of Tokyo, Tokyo 113-8656 (Japan); Huang, Yen-Chin; Chen, Yi-Chun [Department of Physics, National Cheng Kung University, Tainan 70101, Taiwan (China); Chen, Hsiao-Wen; Liu, Hsiang-Lin [Department of Physics, National Taiwan Normal University, Taipei 11677, Taiwan (China); He, Qing [Department of Physics, Durham University, Durham DH1 3LE (United Kingdom); Chu, Ying-Hao, E-mail: yhc@nctu.edu.tw [Department of Materials Science Engineering, National Chiao Tung University, Hsinchu 30010, Taiwan (China); Institute of Physics, Academia Sinica, Taipei 11529, Taiwan (China)

    2015-11-01

    High structural susceptibility of multiferroic BiFeO{sub 3} (BFO) makes it a potential replacement of current Pb-based piezoelectrics. In this study, a tetragonal phase is identified based on a combination of x-ray diffraction, scanning transmission electronic microscopy, x-ray absorption spectroscopy, and Raman spectroscopy when BFO is grown on yttria-stabilized zirconia (YSZ) substrates. To distinguish the discrepancy between this tetragonal phase and common cases of monoclinic BFO, piezoelectric force microscopy images and optical property are also performed. It shows a lower electrostatic energy of ferroelectric domains and a large reduction of band gap for BFO grown on YSZ substrate comparing to the well-known one grown on LaAlO{sub 3} substrate. Our findings in this work can provide more insights to understand the structural diversity of multiferroic BFO system for further applications.

  6. Piezoelectric properties and diffusion phase transition around PPT of La-doped (Na{sub 0.52}K{sub 0.44}Li{sub 0.04}) Nb{sub 0.8}Ta{sub 0.2}O{sub 3} lead-free piezoelectric ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Wenlong, E-mail: yangwenlong1983@163.com; Wang, Li; Li, Haidong; Han, Junsheng; Xiu, Hanjiang; Zhou, Zhongxiang

    2016-10-01

    Lead-free ceramics (Na{sub 0.52}K{sub 0.44}Li{sub 0.04}){sub 1−3x}La{sub x}Nb{sub 0.8}Ta{sub 0.2}O{sub 3} (KNLNT-Lax, x=0.00, 0.25, 0.5, 0.75, 1.00, 1.25 mol%) as non-polluting materials were prepared by solid state reaction method. The structure, piezoelectric proprieties and temperature stability of KNLNT ceramic with different La doping concentrations were investigated. The results show a transition from orthorhombic-tetragonal mix phase to tetragonal single phase with the variation of La{sup 3+} concentrations. The SEM micrographs of surface and fractured surface show a dense microstructure with few micropores. The La-doped KNLTN ceramic will be an alternative candidate contributes to excellent piezoelectric properties, which are found in the 0.75 mol% La-doped KNLNT ceramics, with d{sub 33}=215pC/N, k{sub p}=42.8%and Q{sub m}=89. It has been remarkably improved that the temperature stability of KNLTN-Lax piezoelectric properties at room temperature, and the dielectric relaxation can be observed obviously. The mechanism of La doping was analyzed in terms of valence compensation and polymorphic phase transition (PPT) diffusion. The orthorhombic-tetragonal phase transition around room temperature and the relaxation transition were considered contributing to the excellent piezoelectric performance and improved temperature stability of La{sup 3+}-doped KNLTN.

  7. Mapping grain boundary heterogeneity at the nanoscale in a positive temperature coefficient of resistivity ceramic

    Science.gov (United States)

    Holsgrove, Kristina M.; Kepaptsoglou, Demie M.; Douglas, Alan M.; Ramasse, Quentin M.; Prestat, Eric; Haigh, Sarah J.; Ward, Michael B.; Kumar, Amit; Gregg, J. Marty; Arredondo, Miryam

    2017-06-01

    Despite being of wide commercial use in devices, the orders of magnitude increase in resistance that can be seen in some semiconducting BaTiO3-based ceramics, on heating through the Curie temperature (TC), is far from well understood. Current understanding of the behavior hinges on the role of grain boundary resistance that can be modified by polarization discontinuities which develop in the ferroelectric state. However, direct nanoscale resistance mapping to verify this model has rarely been attempted, and the potential approach to engineer polarization states at the grain boundaries, that could lead to optimized positive temperature coefficient (PTC) behavior, is strongly underdeveloped. Here we present direct visualization and nanoscale mapping in a commercially optimized BaTiO3-PbTiO3-CaTiO3 PTC ceramic using Kelvin probe force microscopy, which shows that, even in the low resistance ferroelectric state, the potential drop at grain boundaries is significantly greater than in grain interiors. Aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy reveal new evidence of Pb-rich grain boundaries symptomatic of a higher net polarization normal to the grain boundaries compared to the purer grain interiors. These results validate the critical link between optimized PTC performance and higher local polarization at grain boundaries in this specific ceramic system and suggest a novel route towards engineering devices where an interface layer of higher spontaneous polarization could lead to enhanced PTC functionality.

  8. Mapping grain boundary heterogeneity at the nanoscale in a positive temperature coefficient of resistivity ceramic

    Directory of Open Access Journals (Sweden)

    Kristina M. Holsgrove

    2017-06-01

    Full Text Available Despite being of wide commercial use in devices, the orders of magnitude increase in resistance that can be seen in some semiconducting BaTiO3-based ceramics, on heating through the Curie temperature (TC, is far from well understood. Current understanding of the behavior hinges on the role of grain boundary resistance that can be modified by polarization discontinuities which develop in the ferroelectric state. However, direct nanoscale resistance mapping to verify this model has rarely been attempted, and the potential approach to engineer polarization states at the grain boundaries, that could lead to optimized positive temperature coefficient (PTC behavior, is strongly underdeveloped. Here we present direct visualization and nanoscale mapping in a commercially optimized BaTiO3–PbTiO3–CaTiO3 PTC ceramic using Kelvin probe force microscopy, which shows that, even in the low resistance ferroelectric state, the potential drop at grain boundaries is significantly greater than in grain interiors. Aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy reveal new evidence of Pb-rich grain boundaries symptomatic of a higher net polarization normal to the grain boundaries compared to the purer grain interiors. These results validate the critical link between optimized PTC performance and higher local polarization at grain boundaries in this specific ceramic system and suggest a novel route towards engineering devices where an interface layer of higher spontaneous polarization could lead to enhanced PTC functionality.

  9. Pulsed Laser Deposition of BaTiO3 Thin Films on Different Substrates

    Directory of Open Access Journals (Sweden)

    Yaodong Yang

    2010-01-01

    Full Text Available We have studied the deposition of BaTiO3 (BTO thin films on various substrates. Three representative substrates were selected from different types of material systems: (i SrTiO3 single crystals as a typical oxide, (ii Si wafers as a semiconductor, and (iii Ni foils as a magnetostrictive metal. We have compared the ferroelectric properties of BTO thin films obtained by pulsed laser deposition on these diverse substrates.

  10. Y-TZP ceramic processing from coprecipitated powders: a comparative study with three commercial dental ceramics.

    Science.gov (United States)

    Lazar, Dolores R R; Bottino, Marco C; Ozcan, Mutlu; Valandro, Luiz Felipe; Amaral, Regina; Ussui, Valter; Bressiani, Ana H A

    2008-12-01

    (1) To synthesize 3mol% yttria-stabilized zirconia (3Y-TZP) powders via coprecipitation route, (2) to obtain zirconia ceramic specimens, analyze surface characteristics, and mechanical properties, and (3) to compare the processed material with three reinforced dental ceramics. A coprecipitation route was used to synthesize a 3mol% yttria-stabilized zirconia ceramic processed by uniaxial compaction and pressureless sintering. Commercially available alumina or alumina/zirconia ceramics, namely Procera AllCeram (PA), In-Ceram Zirconia Block (CAZ) and In-Ceram Zirconia (IZ) were chosen for comparison. All specimens (6mmx5mmx5mm) were polished and ultrasonically cleaned. Qualitative phase analysis was performed by XRD and apparent densities were measured on the basis of Archimedes principle. Ceramics were also characterized using SEM, TEM and EDS. The hardness measurements were made employing Vickers hardness test. Fracture toughness (K(IC)) was calculated. Data were analyzed using one-way analysis of variance (ANOVA) and Tukey's test (alpha=0.05). ANOVA revealed that the Vickers hardness (pceramic materials composition. It was confirmed that the PA ceramic was constituted of a rhombohedral alumina matrix, so-called alpha-alumina. Both CAZ and IZ ceramics presented tetragonal zirconia and alpha-alumina mixture of phases. The SEM/EDS analysis confirmed the presence of aluminum in PA ceramic. In the IZ and CAZ ceramics aluminum, zirconium and cerium in grains involved by a second phase containing aluminum, silicon and lanthanum were identified. PA showed significantly higher mean Vickers hardness values (H(V)) (18.4+/-0.5GPa) compared to vitreous CAZ (10.3+/-0.2GPa) and IZ (10.6+/-0.4GPa) ceramics. Experimental Y-TZP showed significantly lower results than that of the other monophased ceramic (PA) (pceramics (pceramic processing conditions led to ceramics with mechanical properties comparable to commercially available reinforced ceramic materials.

  11. La-doped BaTiO3 heterostructures: Compensating the polarization discontinuity

    Directory of Open Access Journals (Sweden)

    D. P. Kumah

    2013-12-01

    Full Text Available We demonstrate a route to manipulate the polarization and internal electric field of a complex oxide heterostructure using a layering sequence based on the LaAlO3-SrTiO3 interface. By combining sensitive atomic-level mapping of the structure using direct x-ray phase-retrieval methods with theoretical modeling of the electrostatic charge and polarization, we have devised a novel single-domain polar heterostructure. We find that ionic rearrangement results in strain and free energy minimization, and eliminates the polarization discontinuity leading to a two-fold increase of the spontaneous polarization towards the surface of an ultra-thin single-domain BaTiO3 film.

  12. Structural Evolution of the R-T Phase Boundary in KNN-Based Ceramics

    KAUST Repository

    Lv, Xiang

    2017-10-04

    Although a rhombohedral-tetragonal (R-T) phase boundary is known to substantially enhance the piezoelectric properties of potassium-sodium niobate ceramics, the structural evolution of the R-T phase boundary itself is still unclear. In this work, the structural evolution of R-T phase boundary from -150 °C to 200 °C is investigated in (0.99-x)K0.5Na0.5Nb1-ySbyO3-0.01CaSnO3-xBi0.5K0.5HfO3 (where x=0~0.05 with y=0.035, and y=0~0.07 with x=0.03) ceramics. Through temperature-dependent powder X-ray diffraction (XRD) patterns and Raman spectra, the structural evolution was determined to be Rhombohedral (R, <-125 °C) → Rhombohedral+Orthorhombic (R+O, -125 °C to 0 °C) → Rhombohedral+Tetragonal (R+T, 0 °C to 150 °C) → dominating Tetragonal (T, 200 °C to Curie temperature (TC)) → Cubic (C, >TC). In addition, the enhanced electrical properties (e.g., a direct piezoelectric coefficient (d33) of ~450±5 pC/N, a conversion piezoelectric coefficient (d33*) of ~580±5 pm/V, an electromechanical coupling factor (kp) of ~0.50±0.02, and TC~250 °C), fatigue-free behavior, and good thermal stability were exhibited by the ceramics possessing the R-T phase boundary. This work improves understanding of the physical mechanism behind the R-T phase boundary in KNN-based ceramics and is an important step towards their adoption in practical applications. This article is protected by copyright. All rights reserved.

  13. Alumina-zirconium ceramics synthesis by selective laser sintering/melting

    International Nuclear Information System (INIS)

    Shishkovsky, I.; Yadroitsev, I.; Bertrand, Ph.; Smurov, I.

    2007-01-01

    In the present paper, porous refractory ceramics synthesized by selective laser sintering/melting from a mixture of zirconium dioxide, aluminum and/or alumina powders are subjected to optical metallography and X-ray analysis to study their microstructure and phase composition depending on the laser processing parameters. It is shown that high-speed laser sintering in air yields ceramics with dense structure and a uniform distribution of the stabilizing phases. The obtained ceramic-matrix composites may be used as thermal and electrical insulators and wear resistant coating in solid oxide fuel cells, crucibles, heating elements, medical tools. The possibility to reinforce refractory ceramics by laser synthesis is shown on the example of tetragonal dioxide of zirconium with hardened micro-inclusion of Al 2 O 3 . By applying finely dispersed Y 2 O 3 powder inclusions, the type of the ceramic structure is significantly changed

  14. Piezoelectric properties of electrospun nanofibers of BaTiO3; Propiedades piezoeletricas de nanofibras eletrofiadas de BaTiO3

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, L.F.R.M.; Melo, G.F.; Goncalves, A.M.; Eiras, J.A.; Bretas, R.E.S., E-mail: bretas@ufscar.br [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil)

    2016-07-01

    BaTiO3 nanofibers were produced by the electrospinning method from a mixture of a solution of the precursors Ba (CH{sub 3}COO){sub 2} and [(CH{sub 3}){sub 2}CHO]{sub 4}Ti in acetic acid and a solution of poly(vinylpyrrolidone) in ethanol. A voltage of 10 kV and a working distance of 4.6 cm were used for the electrospinning, at controlled room temperature and humidity of 21 °C and 60% respectively. Nanofibers as spun were dried in air on an air-circulating oven at 100 °C for one hour to remove residual solvent and were subsequently calcined at 750 °C during 2 h. The morphology, crystallographic structure and piezoelectric properties of the nanofibers were analyzed by scanning electron microscopy (SEM), X-ray angle (WAXS) and Piezoresponse Force Microscopy (PFM), respectively. The average diameter of the nanofibers was 414 nm with an aspect ratio of 40. By PFM, there was strong evidence that the nanofibers had piezoelectric activity. (author)

  15. Effect of crystal orientation on the phase diagrams, dielectric and piezoelectric properties of epitaxial BaTiO3 thin films

    Directory of Open Access Journals (Sweden)

    Huaping Wu

    2016-01-01

    Full Text Available The influence of crystal orientations on the phase diagrams, dielectric and piezoelectric properties of epitaxial BaTiO3 thin films has been investigated using an expanded nonlinear thermodynamic theory. The calculations reveal that crystal orientation has significant influence on the phase stability and phase transitions in the misfit strain-temperature phase diagrams. In particular, the (110 orientation leads to a lower symmetry and more complicated phase transition than the (111 orientation in BaTiO3 films. The increase of compressive strain will dramatically enhance the Curie temperature TC of (110-oriented BaTiO3 films, which matches well with previous experimental data. The polarization components experience a great change across the boundaries of different phases at room temperature in both (110- and (111-oriented films, which leads to the huge dielectric and piezoelectric responses. A good agreement is found between the present thermodynamics calculation and previous first-principles calculations. Our work provides an insight into how to use crystal orientation, epitaxial strain and temperature to tune the structure and properties of ferroelectrics.

  16. Large-scale synthesis of Pb1-xLa xTiO3 ceramic powders by molten salt method

    International Nuclear Information System (INIS)

    Cai Zongying; Xing Xianran; Yu Ranbo; Liu Guirong; Xing Qifeng

    2006-01-01

    The ferroelectric perovskite type lanthanum doped lead titanate (PLT) ceramic powders were synthesized in one step with the starting materials of PbC 2 O 4 , La 2 O 3 and TiO 2 in NaCl-KCl molten salts in the temperature range of 700-950 deg. C. It was found that molten salt method was a large scale and easy preparation way to produce PLT powders with high dispersity. Tetragonal phase Pb 1-x La x TiO 3 ceramic powders were identified by XRD in the composition range 0 ≤ x ≤ 0.3 and mono-dispersed particles with spheric shape and less than 100 nm size were observed by SEM. The grain sizes of Pb 1-x La x TiO 3 ceramic powders increased with the increase of La content and decreased with calcination temperature. The grain growth progress and the possible reaction mechanism in molten salts and its influencing factors were discussed in this work. The grain growth process was the main influencing factor of the grain size, which depended on the solubility in the flux

  17. Facile Low Temperature Hydrothermal Synthesis of BaTiO3 Nanoparticles Studied by In Situ X-ray Diffraction

    Directory of Open Access Journals (Sweden)

    Ola G. Grendal

    2018-06-01

    Full Text Available Ferroelectric materials are crucial for today’s technological society and nanostructured ferroelectric materials are important for the downscaling of devices. Controlled and reproducible synthesis of these materials are, therefore, of immense importance. Hydrothermal synthesis is a well-established synthesis route, with a large parameter space for optimization, but a better understanding of nucleation and growth mechanisms is needed for full utilization and control. Here we use in situ X-ray diffraction to follow the nucleation and growth of BaTiO3 formed by hydrothermal synthesis using two different titanium precursors, an amorphous titania precipitate slurry and a Ti-citric acid complex solution. Sequential Rietveld refinement was used to extract the time dependency of lattice parameters, crystallite size, strain, and atomic displacement parameters. Phase pure BaTiO3 nanoparticles, 10–15 nm in size, were successfully synthesized at different temperatures (100, 125, and 150 °C from both precursors after reaction times, ranging from a few seconds to several hours. The two precursors resulted in phase pure BaTiO3 with similar final crystallite size. Finally, two different growth mechanisms were revealed, where the effect of surfactants present during hydrothermal synthesis is discussed as one of the key parameters.

  18. Phase structure, dielectric, and piezoelectric properties of (K{sub 0.94-x}Na{sub x}Li{sub 0.06})(Nb{sub 0.94}Sb{sub 0.06})O{sub 3} lead-free ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Lingling; Lin, Dunmin; Zheng, Qiaoji; Wu, Xiaochun; Xu, Chenggang [College of Chemistry and Materials Science, and Visual Computing and Virtual Reality Key Laboratory of Sichuan Province, Sichuan Normal University, Chengdu 610066 (China)

    2012-11-15

    Lead-free piezoelectric ceramics (K{sub 0.94-x}Na{sub x}Li{sub 0.06})(Nb{sub 0.94}Sb{sub 0.06})O{sub 3} have been fabricated by a conventional ceramic technique and the effects of K{sup +}/Na{sup +} ratio on the structure and piezoelectric properties of the ceramics have been studied. All the ceramics possess a pure perovskite structure. The coexistence of tetragonal and orthorhombic phases is formed at room temperature in the ceramics with 0.45 {<=} x {<=} 0.55. The tetragonal-orthorhombic phase-transition temperature T{sub O-T} decreases from 110 to 54 C with x increasing from 0.35 to 0.55 and then increases from 84 to 144 C with x further increasing from 0.6 to 0.7, while the Curie temperature T{sub C} deceases from 388 to 348 C with x increasing from 0.35 to 0.70. Because of the coexistence of the two phases near room temperature, the ceramics with x = 0.50 exhibit the optimum piezoelectric properties: d{sub 33} = 230 pC/N and k{sub p} = 49%. The ceramics possess good time stability of piezoelectric properties. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  19. Thermotropic phase transitions in Pb{sub 1−x}Sr{sub x}(Al{sub 1/3}Nb{sub 2/3}){sub 0.1}(Zr{sub 0.52}Ti{sub 0.48}){sub 0.9}O{sub 3} ceramics: Temperature dependent dielectric permittivity and Raman scattering

    Energy Technology Data Exchange (ETDEWEB)

    Li, C. Q.; Peng, L.; Jiang, K.; Hu, Z. G., E-mail: zghu@ee.ecnu.edu.cn; Chu, J. H. [Key Laboratory of Polar Materials and Devices, Ministry of Education, Department of Electronic Engineering, East China Normal University, Shanghai 200241 (China); Wang, P.; Liu, A. Y. [Department of Physics, Shanghai Normal University, Shanghai 200234 (China)

    2015-06-15

    The phase transitions of Pb{sub 1−x}Sr{sub x}(Al{sub 1/3}Nb{sub 2/3}){sub 0.1}(Zr{sub 0.52}Ti{sub 0.48}){sub 0.9}O{sub 3} (Sr-modified PAN-PZT) ceramics with Sr compositions of x = 2%, 5%, 10% and 15% have been investigated using X-ray diffraction (XRD), temperature dependent dielectric permittivity and Raman scattering. The XRD analysis show that the phase transition occurs between Sr composition of 5% and 10%. Based on the broad dielectric peaks at 100 Hz, the diffused phase transition from tetragonal (T) to cubic (C) structure shifts to lower temperature with increasing Sr composition. The dramatic changes of wavenumber and full width at half-maximum (FWHM) for E(TO{sub 4})′ softing mode can be observed at morphotropic phase boundary (MPB). Moreover, the MPB characteristic shows a wider and lower trend of temperature region with increasing Sr composition. It could be ascribed to the diminishment of the energy barrier and increment of A-cation entropy. Therefore, the Sr-modified PAN-PZT ceramics unambiguously undergo two successive structural transitions (rhombohedral-tetragonal-cubic phase) with temperature from 80 to 750 K. Correspondingly, the phase diagram of Sr-modified PAN-PZT ceramics can be well depicted.

  20. Complementary resistive switching in BaTiO3/NiO bilayer with opposite switching polarities

    Science.gov (United States)

    Li, Shuo; Wei, Xianhua; Lei, Yao; Yuan, Xincai; Zeng, Huizhong

    2016-12-01

    Resistive switching behaviors have been investigated in the Au/BaTiO3/NiO/Pt structure by stacking the two elements with different switching types. The conducting atomic force microscope measurements on BaTiO3 thin films and NiO thin films suggest that with the same active resistive switching region, the switching polarities in the two semiconductors are opposite to each other. It is in agreement with the bipolar hysteresis I-V curves with opposite switching polarities for single-layer devices. The bilayer devices show complementary resistive switching (CRS) without electroforming and unipolar resistive switching (URS) after electroforming. The coexistence of CRS and URS is mainly ascribed to the co-effect of electric field and Joule heating mechanisms, indicating that changeable of resistance in this device is dominated by the redistribution of oxygen vacancies in BaTiO3 and the formation, disruption, restoration of conducting filaments in NiO. CRS in bilayer with opposite switching polarities is effective to solve the sneak current without the introduction of any selector elements or an additional metal electrode.

  1. Preparation and Optical Properties of Infrared Transparent 3Y-TZP Ceramics

    Directory of Open Access Journals (Sweden)

    Chuanfeng Wang

    2017-04-01

    Full Text Available In the present study, a tough tetragonal zirconia polycrystalline (Y-TZP material was developed for use in high-speed infrared windows and domes. The influence of the preparation procedure and the microstructure on the material’s optical properties was evaluated by SEM and FT-IR spectroscopy. It was revealed that a high transmittance up to 77% in the three- to five-micrometer IR region could be obtained when the sample was pre-sintered at 1225 °C and subjected to hot isostatic pressing (HIP at 1275 °C for two hours. The infrared transmittance and emittance at elevated temperature were also examined. The in-line transmittance remained stable as the temperature increased to 427 °C, with degradation being observed only near the infrared cutoff edge. Additionally, the emittance property of 3Y-TZP ceramic at high temperature was found to be superior to those of sapphire and spinel. Overall, the results indicate that Y-TZP ceramic is a potential candidate for high-speed infrared windows and domes.

  2. Residual stress measurement in veneering ceramic by hole-drilling.

    Science.gov (United States)

    Mainjot, Amélie K; Schajer, Gary S; Vanheusden, Alain J; Sadoun, Michaël J

    2011-05-01

    Mismatch in thermal expansion properties between veneering ceramic and metallic or high-strength ceramic cores can induce residual stresses and initiate cracks when combined with functional stresses. Knowledge of the stress distribution within the veneering ceramic is a key factor for understanding and predicting chipping failures, which are well-known problems with Yttria-tetragonal-zirconia-polycrystal based fixed partial dentures. The objectives of this study are to develop a method for measuring the stress profile in veneering ceramics and to compare ceramic-fused-to-metal compounds to veneered Yttria-tetragonal-zirconia-polycrystal ceramic. The hole-drilling method, often used for engineering measurements, was adapted for use with veneering ceramic. Because of the high sensitivity needed in comparison with industrial applications, a high sensitivity electrical measurement chain was developed. All samples exhibited the same type of stress vs. depth profile, starting with compressive at the ceramic surface, decreasing with depth and becoming tensile at 0.5-1.0mm from the surface, and then becoming slightly compressive again. The zirconia samples exhibited a stress depth profile of larger magnitude. The hole drilling method was shown be a practical tool for measuring residual stresses in veneering ceramics. Copyright © 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  3. Effect of temperature and time on solvothermal synthesis of ...

    Indian Academy of Sciences (India)

    Effect of temperature and time study on solvothermal synthesis of BaTiO3 revealed that a moderate reaction temperature i.e. 185◦C and longer reaction time favour tetragonal phase stabiliza- tion. Dissolution–precipitation appears to be the transformation mechanism for the crystallization of BaTiO3 from particulate TiO2 ...

  4. Effect of double layer thickness on magnetoelectric coupling in multiferroic BaTiO3-Bi0.95Gd0.05FeO3 multilayers

    Science.gov (United States)

    Hohenberger, S.; Lazenka, V.; Temst, K.; Selle, S.; Patzig, C.; Höche, T.; Grundmann, M.; Lorenz, M.

    2018-05-01

    The effect of double-layer thickness and partial substitution of Bi3+ by Gd3+ is demonstrated for multiferroic BaTiO3–BiFeO3 2–2 heterostructures. Multilayers of 15 double layers of BaTiO3 and Bi0.95Gd0.05FeO3 were deposited onto (0 0 1) oriented SrTiO3 substrates by pulsed laser deposition with various double layer thicknesses. X-ray diffraction and high resolution transmission electron microscopy investigations revealed a systematic strain tuning with layer thickness via coherently strained interfaces. The multilayers show increasingly enhanced magnetoelectric coupling with reduced double layer thickness. The maximum magnetoelectric coupling coefficient was measured to be as high as 50.8 V cm‑1 Oe‑1 in 0 T DC bias magnetic field at room temperature, and 54.9 V cm‑1 Oe‑1 above 3 T for the sample with the thinnest double layer thickness of 22.5 nm. This enhancement is accompanied by progressively increasing perpendicular magnetic anisotropy and compressive out-of-plane strain. To understand the origin of the enhanced magnetoelectric coupling in such multilayers, the temperature and magnetic field dependency of is discussed. The magnetoelectric performance of the Gd3+ substituted samples is found to be slightly enhanced when compared to unsubstituted BaTiO3–BiFeO3 multilayers of comparable double-layer thickness.

  5. A first-principles study of phase transitions in ultrathin films of BaTiO 3

    Indian Academy of Sciences (India)

    We determine the effects of film thickness, epitaxial strain and the nature of electrodes on ferroelectric phase transitions in ultrathin films of BaTiO3 using a first-principles effective Hamiltonian in classical molecular dynamics simulations. We present results for polarization and dielectric properties as a function of temperature ...

  6. A New Method to Improve the Electrical Properties of KNN-based Ceramics: Tailoring Phase Fraction

    KAUST Repository

    Lv, Xiang; Wu, Jiagang; Zhu, Jianguo; Xiao, Dingquan; Zhang, Xixiang

    2017-01-01

    Although both the phase type and fraction of multi-phase coexistence can affect the electrical properties of (K,Na)NbO3 (KNN)-based ceramics, effects of phase fraction on their electrical properties were few concerned. In this work, through changing the calcination temperature of CaZrO3 powders, we successfully developed the 0.96K0.5Na0.5Nb0.96Sb0.04O3-0.01CaZrO3-0.03Bi0.5Na0.5HfO3 ceramics containing a wide rhombohedral-tetragonal (R-T) phase coexistence with the variations of T (or R) phase fractions. It was found that higher T phase fraction can warrant a larger piezoelectric constant (d33) and d33 also showed a linear variation with respect to tetragonality ratio (c/a). More importantly, a number of domain patterns were observed due to high T phase fraction and large c/a ratio, greatly benefiting the piezoelectricity. In addition, the improved ferroelectric fatigue behavior and thermal stability were also shown in the ceramics containing high T phase fraction. Therefore, this work can bring a new viewpoint into the physical mechanism of KNN-based ceramics behind R-T phase coexistence.

  7. A New Method to Improve the Electrical Properties of KNN-based Ceramics: Tailoring Phase Fraction

    KAUST Repository

    Lv, Xiang

    2017-08-18

    Although both the phase type and fraction of multi-phase coexistence can affect the electrical properties of (K,Na)NbO3 (KNN)-based ceramics, effects of phase fraction on their electrical properties were few concerned. In this work, through changing the calcination temperature of CaZrO3 powders, we successfully developed the 0.96K0.5Na0.5Nb0.96Sb0.04O3-0.01CaZrO3-0.03Bi0.5Na0.5HfO3 ceramics containing a wide rhombohedral-tetragonal (R-T) phase coexistence with the variations of T (or R) phase fractions. It was found that higher T phase fraction can warrant a larger piezoelectric constant (d33) and d33 also showed a linear variation with respect to tetragonality ratio (c/a). More importantly, a number of domain patterns were observed due to high T phase fraction and large c/a ratio, greatly benefiting the piezoelectricity. In addition, the improved ferroelectric fatigue behavior and thermal stability were also shown in the ceramics containing high T phase fraction. Therefore, this work can bring a new viewpoint into the physical mechanism of KNN-based ceramics behind R-T phase coexistence.

  8. Superior Properties of Energetically Stable La2/3Sr1/3MnO3/Tetragonal BiFeO3 Multiferroic Superlattices

    KAUST Repository

    Feng, Nan; Mi, Wenbo; Wang, Xiaocha; Cheng, Yingchun; Schwingenschlö gl, Udo

    2015-01-01

    The superlattice of energetically stable La2/3Sr1/3MnO3 and tetragonal BiFeO3 is investigated by means of density functional theory. The superlattice as a whole exhibits a half-metallic character, as is desired for spintronic devices. The interfacial electronic states and exchange coupling are analyzed in details. We demonstrate that the interfacial O atoms play a key role in controlling the coupling. The higher ferroelectricity of tetragonal BiFeO3 and stronger response to the magnetic moment in La2/3Sr1/3MnO3/BiFeO3 superlattice show a strongly enhanced electric control of the magnetism as compared to the rhombohedral one. Therefore, it is particularly practical interest in the magnetoelectric controlled spintronic devices.

  9. Superior Properties of Energetically Stable La2/3Sr1/3MnO3/Tetragonal BiFeO3 Multiferroic Superlattices

    KAUST Repository

    Feng, Nan

    2015-04-30

    The superlattice of energetically stable La2/3Sr1/3MnO3 and tetragonal BiFeO3 is investigated by means of density functional theory. The superlattice as a whole exhibits a half-metallic character, as is desired for spintronic devices. The interfacial electronic states and exchange coupling are analyzed in details. We demonstrate that the interfacial O atoms play a key role in controlling the coupling. The higher ferroelectricity of tetragonal BiFeO3 and stronger response to the magnetic moment in La2/3Sr1/3MnO3/BiFeO3 superlattice show a strongly enhanced electric control of the magnetism as compared to the rhombohedral one. Therefore, it is particularly practical interest in the magnetoelectric controlled spintronic devices.

  10. Composition-Driven Phase Boundary and Piezoelectricity in Potassium-Sodium Niobate-Based Ceramics.

    Science.gov (United States)

    Zheng, Ting; Wu, Jiagang; Xiao, Dingquan; Zhu, Jianguo; Wang, Xiangjian; Lou, Xiaojie

    2015-09-16

    The piezoelectricity of (K,Na)NbO3 ceramics strongly depends on the phase boundary types as well as the doped compositions. Here, we systematically studied the relationships between the compositions and phase boundary types in (K,Na) (Nb,Sb)O3-Bi0.5Na0.5AO3 (KNNS-BNA, A=Hf, Zr, Ti, Sn) ceramics; then their piezoelectricity can be readily modified. Their phase boundary types are determined by the doped elements. A rhombohedral-tetragonal (R-T) phase boundary can be driven in the compositions range of 0.035≤BNH≤0.040 and 0.035≤BNZ≤0.045; an orthorhombic-tetragonal (O-T) phase boundary is formed in the composition range of 0.005≤BNT≤0.02; and a pure O phase can be only observed regardless of BNS content (≤0.01). In addition, the phase boundary types strongly affect their corresponding piezoelectricities. A larger d33 (∼440-450 pC/N) and a higher d33* (∼742-834 pm/V) can be attained in KNNS-BNA (A=Zr and Hf) ceramics due to the involvement of R-T phase boundary, and unfortunately KNNS-BNA (A=Sn and Ti) ceramics possess a relatively poor piezoelectricity (d33≤200 and d33*piezoelectricity and phase boundary types were also discussed. We believe that comprehensive research can design more excellent ceramic systems concerning potassium-sodium niobate.

  11. High field dielectric properties of anisotropic polymer-ceramic composites

    International Nuclear Information System (INIS)

    Tomer, V.; Randall, C. A.

    2008-01-01

    Using dielectrophoretic assembly, we create anisotropic composites of BaTiO 3 particles in a silicone elastomer thermoset polymer. We study a variety of electrical properties in these composites, i.e., permittivity, dielectric breakdown, and energy density as function of ceramic volume fraction and connectivity. The recoverable energy density of these electric-field-structured composites is found to be highly dependent on the anisotropy present in the system. Our results indicate that x-y-aligned composites exhibit higher breakdown strengths along with large recoverable energy densities when compared to 0-3 composites. This demonstrates that engineered anisotropy can be employed to control dielectric breakdown strengths and nonlinear conduction at high fields in heterogeneous systems. Consequently, manipulation of anisotropy in high-field dielectric properties can be exploited for the development of high energy density polymer-ceramic systems

  12. Hybrid chitosan–Pluronic F-127 films with BaTiO3:Co nanoparticles: Synthesis and properties

    International Nuclear Information System (INIS)

    Fuentes, S.; Dubo, J.; Barraza, N.; González, R.; Veloso, E.

    2015-01-01

    In this study, magnetic BaTiO 3 :Co (BT:Co) nanoparticles prepared using a combined sol–gel–hydrothermal technique were dispersed in a chitosan/Pluronic F-127 solution (QO/Pl) to obtain a nanocomposite hybrid films. Nanoparticles and hybrid films were characterized by X-ray powder diffraction, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and alternating gradient magnetometry (AGM). Experimental results indicated that the BT:Co nanoparticles were encapsulated in the QO/Pl hybrid films and that the magnetic properties of the QO/Pl/BT:Co nanocomposites are similar to the naked BT:Co nanoparticles. Results indicate that Co doping produces an enhancement in the ferromagnetic behavior of the BT nanoparticle. The coating restricts this enhancement only to low-fields, leaving the diamagnetic behavior of BT at high-fields. Magnetically stable sizes (PSD) were obtained at 3% Co doping for both naked nanoparticles and hybrid films. These show an increased magnetic memory capacity and a softer magnetic hardness with respect to non-doped BT nanoparticles. - Highlights: • We described the synthesis of magnetic BaTiO 3 :Co dispersed in chitosan (QO)/Pluronic F-127 (Pl) solution by sonication to obtain nanocomposite hybrid films. • We describe the physical and magnetic properties of BaTiO 3 :Co nanoparticles and QO/Pl/BT:Co hybrid films. • The magnetic properties are defines by the presence of magnetic domains. These magnetic domains are close related with the amount of Co in the host lattice. • The prepared phases could be considered as multifunctional materials, with magnetic and ferri-electrical properties, with potential uses in the design of devices

  13. Effects of Sr2+ doping on the electrical properties of (Bi0.5Na0.50.94Ba0.06TiO3 ceramics

    Directory of Open Access Journals (Sweden)

    Amrita Singh

    2015-03-01

    Full Text Available The influence of SrTiO3 addition on the microstructure and various electrical properties of (Bi0.5Na0.50.94Ba0.06TiO3 (BNTBT6 ceramics, fabricated by a conventional high temperature solid state reaction, was investigated. Analysis of X-ray diffraction patterns revealed the formation of phase pure materials with tetragonal unit cell structure, tetragonality parameter c/a in the interval from 0.9940 to 1.0063 and crystallite sizes ranging from 33–76 nm for addition of 0.2 to 1 wt.% of SrTiO3. SEM studies indicated that Sr2+ doping led to decrease in grain size and non-homogeneity of grain distribution for higher SrTiO3 amount (>0.6 wt.%. Complex impedance, modulus, and conductivity studies indicated the presence of grains and grain boundary contribution, non-Debye type of relaxation and NTCR behaviour of the test ceramic samples. Temperature dependent real part of complex permittivity showed peaks at 475 °C and the dielectric loss tangent showed peaks corresponding to 125 °C and 475 °C for almost all compositions. AC activation energies, computed using Arrhenius relation in the temperature range of 325–500 °C for the BNTBT6 ceramic compositions having SrTiO3 concentration from 0.2 to 1.0 wt.%, were seen to have maximal values at the lowest measurement frequency. Amongst the different chosen doped BNTBT6 ceramic compositions, the composition having 0.6 wt.% of SrTiO3 showed the best ferroelectric and piezoelectric response with maximum value of Pr (8.24 µC/cm2, minimum value of Ec (5.73 kV/mm and maximum d33 value (∼46 pC/N.

  14. Multiferroic properties of BiFeO3/BaTiO3 multilayered thin films

    International Nuclear Information System (INIS)

    Sharma, Savita; Tomar, Monika; Kumar, Ashok; Puri, Nitin K.; Gupta, Vinay

    2014-01-01

    Multilayered structures of multiferroic BiFeO 3 (BFO) and ferroelectric BaTiO 3 (BTO) have been fabricated using pulsed laser deposition (PLD). Ferromagnetic and ferroelectric properties of the multilayered system (BFO/BTO) have been investigated. It could be inferred that the magnetization increases with the incorporation of BTO buffer layer, which indicates a coupling between the ferroelectric and ferromagnetic orders. Vibrating sample magnetometer (VSM) measurements performed on the prepared multiferroic samples show that the magnetization is significantly increased (M s =56.88 emu/cm 3 ) for the multilayer system with more number of layers (four) keeping the total thickness of the multilayered system constant (350 nm) meanwhile maintaining the sufficiently enhanced ferroelectric properties (P r =29.68 µC/cm 2 )

  15. Effects of SrTiO3 on dielectric and piezoelectric properties of K0.48Na0.48Li0.04Nb0.96Ta0.04O3-based piezoceramics

    International Nuclear Information System (INIS)

    Bafandeh, Mohammad Reza; Abbasi, Mohammad Hasan; Saidi, Ali; Lee, Jae-Shin

    2013-01-01

    Highlights: ► Sodium potassium niobate based piezoceramics modified with SrTiO 3 (ST) were prepared. ► Crystal structure, microstructure and dielectric properties of ceramics were investigated. ► Addition of ST more than 3 mol% changed ferroelectric behavior from normal to relaxor. ► Coexistence of two structures in ceramic with 1 mol% ST enhanced piezoelectric constant. - Abstract: In this study, (100 − x) K 0.48 Na 0.48 Li 0.04 Nb 0.96 Ta 0.04 O 3 − xSrTiO 3 (0 ≤ x ≤ 10) ceramics were fabricated via normal sintering of synthesized powder by using solid state reaction. All ceramics revealed pure perovskite structure, indicating formation of solid solution between KNNLT and ST up to 10%. With increasing x, the crystal structure of ceramics changed from orthorhombic to tetragonal and finally pseudocubic symmetry when x = 10. Ceramic containing 1% ST had orthorhombic and tetragonal symmetries, simultaneously. Investigation of the variation of dielectric constant of ceramics versus temperature revealed that for ceramic with x = 1, polymorphic phase transition (PPT) temperature between orthorhombic and tetragonal is less than room temperature. Thus coexistence of two different structures in this ceramic is due to vicinity of its composition to morphotropic phase boundary (MPB). As a result, the maximum piezoelectric constant was measured for this ceramic. Ceramics containing 5 and 7.5% ST tend to appear relaxor ferroelectric behavior which is because of chemical inhomogeneities in both A- and B-sites of the ABO 3 perovskite structure.

  16. Study on effect of cubic- and tetragonal phased BaTiO{sub 3} on the electrical and thermal properties of polymeric nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Thanki, A.A.; Goyal, R.K., E-mail: rkgoyal72@yahoo.co.in

    2016-11-01

    Polymer matrix nanocomposites based on polycarbonate (PC) and nanosized-cubic/tetragonal phases of barium titanate (BaTiO{sub 3}) were fabricated using a solution method followed by hot pressing. The content of both cubic- and tetragonal phased BaTiO{sub 3} was varied from 0 to 50 wt%. For a given weight fraction, the dielectric constant of the nanocomposites containing tetragonal BaTiO{sub 3} is more than those of cubic BaTiO{sub 3} filled nanocomposites. Moreover, cubic BaTiO{sub 3}/PC nanocomposites showed significantly lower dissipation factor than those of tetragonal BaTiO{sub 3}/PC nanocomposites. The dielectric constant of the nanocomposites was found to be frequency-independent. The microhardness of the nanocomposites increased with increase in the BaTiO{sub 3} content (both cubic- and tetragonal-phased) compared to the pure matrix. Scanning electron microscopy showed better dispersion and good interaction of the tetragonal BaTiO{sub 3} nanoparticles in the matrix. The addition of cubic BaTiO{sub 3} nanoparticles significantly reduced the thermal stability of the nanocomposites compared to matrix while the addition of tetragonal BaTiO{sub 3} nanoparticles decreased it slightly. The glass transition temperature of the cubic BaTiO{sub 3}/PC nanocomposites decreased significantly, whereas it reduced slightly for the tetragonal BaTiO{sub 3}/PC nanocomposites. - Highlights: • The effect of cubic-BaTiO{sub 3} and tetragonal-BaTiO{sub 3} nanoparticles were studied. • Cubic-BaTiO{sub 3} nanoparticles showed better microhardness. • Tetragonal-BaTiO{sub 3} nanoparticles showed better dielectric and thermal properties. • Frequency independent dielectric constants of the nanocomposites were observed.

  17. Reflectance of Co- and Nb-doped BaTiO3 for photon energies from 1.8 to 70 eV

    International Nuclear Information System (INIS)

    Goudonnet, J.P.; Godefroy, G.; Inagaki, T.; Moretti, P.; Williams, M.W.; Arakawa, E.T.

    1985-01-01

    The reflectance spectra of Co- and Nb-doped BaTiO 3 crystals have been measured for photon energies from 1.8 to 70 eV. For both types of crystal, structures observed in the 1.8 to 2.3 eV range can be attributed to the presence of residual impurities. Between 2.3 and 3.2 eV the peaks in the reflectance of the Co-doped crystal are found to be of an acceptor charge transfer type. For Nb-doped crystals structures appear at the bottom of the conduction band. For energies larger than 3.2 eV the spectra are characteristic of pure BaTiO 3 crystals, in reasonable agreement with those determined by Baeuerle et al. and calculated by Michel-Calendini and Moretti. 15 refs., 4 figs., 1 tab

  18. Residual tensile stresses and piezoelectric properties in BiFeO3-Bi(Zn1/2Ti1/2O3-PbTiO3 ternary solid solution perovskite ceramics

    Directory of Open Access Journals (Sweden)

    Weilin Zheng

    2016-08-01

    Full Text Available For low dielectric loss perovskite-structured (1-x-yBiFeO3-xBi(Zn1/2Ti1/2O3-yPbTiO3 (BF-BZT-PT (x = 0.04-0.15 and y = 0.15-0.26 ceramics in rhombohedral/tetragonal coexistent phase, structural phase transitions were studied using differential thermal analyzer combined with temperature-dependent dielectric measurement. Two lattice structural phase transitions are disclosed in various BF-BZT-PT perovskites, which is different from its membership of BiFeO3 exhibiting just one lattice structural phase transition at Curie temperature TC= 830oC. Consequently, residual internal tensile stresses were revealed experimentally through XRD measurements on ceramic pellets and counterpart powders, which are reasonably attributed to special structural phase transition sequence of BF-BZT-PT solid solution perovskites. Low piezoresponse was observed and argued extrinsically resulting from residual tensile stresses pinning ferroelectric polarization switching. Post-annealing and subsequent quenching was found effective for eliminating residual internal stresses in those BZT-less ceramics, and good piezoelectric property of d33 ≥ 28 pC/N obtained for 0.70BF-0.08BZT-0.22PT and 0.05 wt% MnO2-doped 0.70BF-0.04BZT-0.26PT ceramics with TC ≥ 640oC, while it seemed no effective for those BZT-rich BF-BZT-PT ceramics with x = 0.14 and 0.15 studied here.

  19. Effect of B-site substitution of complex ions on dielectric and piezoelectric properties in (Bi1/2Na1/2)TiO3 piezoelectric ceramics

    International Nuclear Information System (INIS)

    Zhou Changrong; Liu Xinyu

    2008-01-01

    The effect of B-site substitution of complex ions on dielectric and piezoelectric properties in (Bi 1/2 Na 1/2 )Ti 1-x (Zn 1/3 Nb 2/3 ) x O 3 (BNTZN-100x) lead-free piezoelectric ceramics was investigated. X-ray diffraction analysis shows that the materials are mono-perovskite phase. The morphotropic phase boundary (MPB) of BNTZN-100x ceramics between rhombohedral and tetragonal locates in the range of 0.5% ≤ x ≤ 2.0%. Temperature dependence of dielectric constant shows that these compounds are relaxor ferroelectrics. The compositions near the MPB exhibit relatively high piezoelectric properties. The piezoelectric constant (d 33 ) and the electromechanical coupling factor (k t ) show the maximum values of d 33 = 97 pC N -1 and k t = 0.46 at x = 2.0% and x = 1.0%, respectively. The BNTZN-100x ceramics are good candidate for use as ultrasonic transducer ceramics for high anisotropic with high k t value and low k p value

  20. In-situ structural investigations of ferroelasticity in soft and hard rhombohedral and tetragonal PZT

    Energy Technology Data Exchange (ETDEWEB)

    Morozov, Maxim I., E-mail: maximm@alumni.ntnu.no; Einarsrud, Mari-Ann; Tolchard, Julian R.; Grande, Tor [Department of Materials Science and Engineering, Norwegian University of Science and Technology, NO-7491 Trondheim (Norway); Geiger, Philipp T.; Webber, Kyle G. [Department of Materials Science, Friedrich-Alexander-Universität Erlangen-Nürnberg, 91058 Erlangen (Germany); Damjanovic, Dragan [Ceramics Laboratory, Swiss Federal Institute of Technology in Lausanne-EPFL, 1015 Lausanne (Switzerland)

    2015-10-28

    Despite the technological importance of hard and soft PZT, Pb(Zr,Ti)O{sub 3}, ceramics, the mechanisms of ferroelectric hardening and softening remain widely discussed in the literature. The hardening and softening phenomena have traditionally been investigated in relation with dielectric manifestations such as aging of the dielectric susceptibility and constriction of the polarization-electric field hysteresis loop. Here, we present a systematic investigation of the ferroelectric and ferroelastic properties of soft and hard PZT in both the tetragonal and rhombohedral phases. A particular focus has been devoted to ferroelastic domain switching by characterizing the macroscopic mechanical constitutive behavior and in-situ synchrotron X-ray diffraction during compression. It is demonstrated that variation of the ordering state of point defects in PZT ceramics affects the switching behavior of both ferroelectric and ferroelastic domains under mechanical or electrical fields. Softening of the mechanical and electrical properties of originally hard PZT ceramics was conferred by quenching the materials from above the Curie temperature. The present findings are discussed with respect to the current understanding of hardening-softening transitions in ferroelectric materials.

  1. Effects of Nb and Sr doping on crystal structure of epitaxial BaTiO3 thin films on MgO substrates

    International Nuclear Information System (INIS)

    Kim, Yongsam; Chen, Chunhua; Saiki, Atsushi; Wakiya, Naoki; Shinozaki, Kazuo; Mizutani, Nobuyasu

    2002-01-01

    Niobium (Nb) and strontium (Sr) doped barium titanate (BT) films were deposited by radio frequency (RF) magnetron sputtering with Nb and Sr doped BT ceramic targets, respectively. The effect of Nb and Sr doping on the crystal structure of epitaxial BaTiO 3 thin films on MgO substrates was investigated. The crystal structure of the films was examined using the reciprocal space mapping measurement. All the films exhibit a cube-on-cube relation with respect to the substrates. As the amount of doped Sr increased, both of the in-plane and out-of-plane lattice constants of Sr doped BT films slowly approached the BT bulk values. On the other hand, the lattice constants of Nb doped BT films were rapidly coming close to the bulk values. These indicated that the lattices of doped BT films were relaxed as the amount of doped elements increased. In addition, Nb doping had greater influence on the relaxation of the films than Sr doping for the same content of dopant. (author)

  2. Microstructure evolution and phase transition in La/Mn doped barium titanate ceramics

    Directory of Open Access Journals (Sweden)

    Vesna Paunović

    2010-12-01

    Full Text Available La/Mn codoped BaTiO3 with different La2O3 content, ranging from 0.1 to 5.0 at% La, was investigated regarding their microstructural and dielectric characteristics. The content of 0.05 at% Mn was constant in all investigated samples. The samples were sintered at 1320°C and 1350°C for two hours. Microstructural studies were done using SEM and EDS analysis. The fine-grained microstructure was obtained even for low content of La. The appearance of secondary abnormal grains with serrated features along grain boundaries was observed in 1.0 at% La-BaTiO3 sintered at 1350°C. Nearly flat permittivity-temperature response was obtained in specimens with 2.0 and 5.0 at% La. Using the modified Curie-Weiss law a critical exponent γ and C’were calculated. The obtained values of γ pointed out the diffuse phase transformation in heavily doped BaTiO3 and great departure from the Curie-Weiss law for low doped ceramics.

  3. Optical properties of BaTiO3 nanoparticles and silver nanoprisms in polymer host matrices

    Science.gov (United States)

    Requena, Sebastian

    Nanocomposites are materials comprised of a host matrix, such as glass or polymer, with embedded nanoparticles. Embedding nanoparticles into the host makes it possible to create materials with properties that are distinctly unique from those of their host and nanoparticle constituents. Nanocomposites can have superior mechanical, thermal, and optical properties compared to their host materials. We characterized the photoluminescent properties of BaTiO3 polymer nanocomposites and the effects of chemically modifying the nanoparticles surface on said properties. BaTiO3 nanopowders of average grain sizes 50 nm and 100 nm were functionalized by (3-aminopropyl)triethoxysilane (3APTS) and mixed with poly(methyl methacrylate)/toluene solution. The nanocomposites films morphology and chemical structure were studied via AFM and FTIR. The photoluminescence spectrum of the pure nanoparticles was composed of an emission at ˜3.0 eV and multiple bands centered at ˜2.5 eV. Surface functionalization of the BaTiO3 nanoparticles via 3APTS increased overall luminescence at room temperature while only enhancing the ˜3.0 eV emission at low-temperature. On the other hand, polymer coating of the functionalized nanoparticles significantly enhances ˜3.0 eV emissions while decreasing emissions associated with near-surface lattice distortions at ˜2.5 eV. Chemical modification of the surface with 3APTS and PMMA presents a pathway to tune and control the photoluminescent properties of BTO nanoparticles. We also present optical studies of two different size distributions of silver triangular nanoprisms, one with a dipole resonance at ˜520 nm and the other with a dipole resonance at ˜650 nm, placed in different media. The silver nanoprisms were embedded in a polyvinyl alcohol (PVA) polymer matrix and oriented by stretching the polymer/nanoprism nanocomposite films. We observe significantly increased linear dichroism in the region associated with the plasmonic in-plane dipole mode upon

  4. Contribution of the irreversible displacement of domain walls to the piezoelectric effect in barium titanate and lead zirconate titanate ceramics

    CERN Document Server

    Damjanovic, D

    1997-01-01

    The contribution from the irreversible displacement of non-180 deg domain walls to the direct longitudinal piezoelectric d sub 3 sub 3 coefficient of BaTiO sub 3 and Pb(Zr, Ti)O sub 3 ceramics was determined quantitatively by using the Rayleigh law. Effects of the crystal structure and microstructure of the ceramics as well as the external d.c. pressure on the domain wall contribution to d sub 3 sub 3 were examined. In barium titanate, this domain wall contribution is large (up to 35% of the total d sub 3 sub 3 , under the experimental conditions used) and dependent on the external d.c. pressure in coarse grained ceramics, and much smaller and independent of the external d.c. pressure in fine-grained samples. The presence of internal stresses in fine-grained ceramics could account for the observed behaviour. The analysis shows that the domain-wall contribution to the d sub 3 sub 3 in lead zirconate titanate ceramics is large in compositions close to the morphotropic phase boundary that contain a mixture of te...

  5. Mnx/2Nbx/2O3 ceramics

    Indian Academy of Sciences (India)

    Unknown

    Abstract. The paper reports investigations of relative permittivity, εr, electrical conductivity, σ, saturation polarization, Ps, infrared absorption and structural properties of compensating valency substituted BaTiO3. The compositions investigated are BaTi(1–x)Mnx/2Nbx/2O3 for x = 0⋅00; 0⋅025; 0⋅05; 0⋅1; 0⋅2; 0⋅4.

  6. Substantial enhancement of energy storage capability in polymer nanocomposites by encapsulation of BaTiO3 NWs with variable shell thickness.

    Science.gov (United States)

    Wang, Guanyao; Huang, Yanhui; Wang, Yuxin; Jiang, Pingkai; Huang, Xingyi

    2017-08-09

    Dielectric polymer nanocomposites have received keen interest due to their potential application in energy storage. Nevertheless, the large contrast in dielectric constant between the polymer and nanofillers usually results in a significant decrease of breakdown strength of the nanocomposites, which is unfavorable for enhancing energy storage capability. Herein, BaTiO 3 nanowires (NWs) encapsulated by TiO 2 shells of variable thickness were utilized to fabricate dielectric polymer nanocomposites. Compared with nanocomposites with bare BaTiO 3 NWs, significantly enhanced energy storage capability was achieved for nanocomposites with TiO 2 encapsulated BaTiO 3 NWs. For instance, an ultrahigh energy density of 9.53 J cm -3 at 440 MV m -1 could be obtained for nanocomposites comprising core-shell structured nanowires, much higher than that of nanocomposites with 5 wt% raw ones (5.60 J cm -3 at 360 MV m -1 ). The discharged energy density of the proposed nanocomposites with 5 wt% mTiO 2 @BaTiO 3 -1 NWs at 440 MV m -1 seems to rival or exceed those of some previously reported nanocomposites (mostly comprising core-shell structured nanofillers). More notably, this study revealed that the energy storage capability of the nanocomposites can be tailored by the TiO 2 shell thickness. Finite element simulations were employed to analyze the electric field distribution in the nanocomposites. The enhanced energy storage capability should be mainly attributed to the smoother gradient of dielectric constant between the nanofillers and polymer matrix, which alleviated the electric field concentration and leakage current in the polymer matrix. The methods and results herein offer a feasible approach to construct high-energy-density polymer nanocomposites with core-shell structured nanowires.

  7. The possibility of giant dielectric materials for multilayer ceramic capacitors.

    Science.gov (United States)

    Ishii, Tatsuya; Endo, Makoto; Masuda, Kenichiro; Ishida, Keisuke

    2013-02-11

    There have been numerous reports on discovery of giant dielectric permittivity materials called internal barrier layer capacitor in the recent years. We took particular note of one of such materials, i.e., BaTiO 3 with SiO 2 coating. It shows expressions of giant electric permittivity when processed by spark plasma sintering. So we evaluated various electrical characteristics of this material to find out whether it is applicable to multilayer ceramic capacitors. Our evaluation revealed that the isolated surface structure is the sole cause of expressions of giant dielectric permittivity.

  8. Compensation mechanisms at high temperature in Y-doped BaTiO3

    International Nuclear Information System (INIS)

    Paredes-Olguín, M.; Lira-Hernández, I.A.; Gómez-Yáñez, C.; Espino-Cortés, F.P.

    2013-01-01

    Samples of BaTiO 3 with different concentrations of Y were synthesized from powders. The mixtures of powders were pressed and sintered at 1500 °C for 1 h. Two groups of samples were processed, one satisfying Ba/(Ti+Y) 3+ occupies the Ti 4+ lattice sites. The conductivity behavior as a function of Y concentration suggests that the compensation mechanisms are hole and oxygen vacancies. Due to the presence of charge carriers in the material, high values for the dielectric constant and dielectric loss were observed. Analysis of the microstructure showed that the average grain size decreases as the Y concentration is increased.

  9. The covalent effect on the energy levels of d3 ions in tetragonal compounds

    International Nuclear Information System (INIS)

    Li, Dong-Yang; Du, Mao-Lu

    2015-01-01

    For d 3 ions in covalent compounds with tetragonal symmetry, this paper presents a complete energy matrix, in which the different covalence of t 2 and e orbitals is considered not only in the electrostatic repulsions part of energy matrix elements but also in the crystal-field potential part of energy matrix elements. With taking and no taking the crystal field parameter B 00 0 into account, the effect of covalence on the energy levels of d 3 ions system were investigated, respectively. The investigation shows that it is very necessary for considering the different covalence of t 2 and e orbitals in both electrostatic repulsions part and crystal-field potential part when the optical properties of d 3 ions in strong covalent compounds with tetragonal symmetry is investigated. On the other hand, the crystal field parameter B 00 0 has a significant effect on the energy levels, and should be considered in investigations of d 3 ions in strong covalent compounds with tetragonal symmetry. Application to calculating the energy levels for Co 2+ in CdGa 2 Se 4 , the calculated results are in agreement with the experiment data

  10. Synthesis of flower-like BaTiO3/Fe3O4 hierarchically structured particles and their electrorheological and magnetic properties.

    Science.gov (United States)

    Wang, Baoxiang; Yin, Yichao; Liu, Chenjie; Yu, Shoushan; Chen, Kezheng

    2013-07-21

    Flower-like BaTiO3/Fe3O4 hierarchically structured particles composed of nano-scale structures on micro-scale materials were synthesized by a simple solvothermal approach and characterized by the means of X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), magnetic testing and rotary viscometer. The influences on the morphology and structure of solvothermal times, type and amount of surfactant, EG : H2O ratio, etc. were studied. Magnetic testing results show that the samples have strong magnetism and they exhibit superparamagnetic behavior, as evidenced by no coercivity and the remanence at room temperature, due to their very small sizes, observed on the M-H loop. The saturation magnetization (M(s)) value can achieve 18.3 emu g(-1). The electrorheological (ER) effect was investigated using a suspension of the flower-like BaTiO3/Fe3O4 hierarchically structured particles dispersed in silicone oil. We can observe a slight shear-thinning behavior of shear viscosity at a low shear rate region even at zero applied electric field and a Newtonian fluid behavior at high shear rate regions.

  11. Phase development and dielectric properties of (1-x)Pb(Zr0.52Ti0.48)O3-xBaTiO3 ceramics

    International Nuclear Information System (INIS)

    Chaisan, Wanwilai; Yimnirun, Rattikorn; Ananta, Supon; Cann, David P.

    2006-01-01

    (1-x)Pb(Zr 0.52 Ti 0.48 )O 3 -xBaTiO 3 ceramics were prepared by a modified mixed-oxide method. The phase formation was studied by XRD analysis. All compositions exhibit complete solid solutions of perovskite-like phase in the (1-x)PZT-xBT system. The (2 0 0)/(0 0 2) peak was found to split at the composition x = 0.6 and the co-existence of tetragonal-rhombohedral phases occurs with x ≤ 0.6. The possible range of compositions which correspond to a phase transition is 0.6 < x < 0.7. While pure BT ceramics exhibited a sharp phase transformation expected for normal ferroelectrics, phase transformation behavior of the (1-x)PZT-xBT solid solutions became more diffuse with increasing BT contents. This was primarily evidenced by an increased broadness in the dielectric peak, with a maximum peak width occurring at x = 0.5

  12. Effects of Reaction Medium on the Phase Synthesis and Particle Size Evolution of BaTiO3

    NARCIS (Netherlands)

    Stawski, Thomasz M.; Veldhuis, Sjoerd A.; Göbel, Ole; ten Elshof, Johan E.; Blank, David H.A.

    2010-01-01

    The low-temperature alkoxide–hydroxide precipitation synthesis of nanosized crystalline barium titanate (BaTiO3) in nonaqueous media is presented. In this report, we show the influence of the reaction medium on the nature of the product by investigating the reaction of titanium (IV) isopropoxide

  13. Superplasticity in fine-grained ceramics. Final report, 1 July 1993--31 December 1993

    Energy Technology Data Exchange (ETDEWEB)

    Nieh, T.G.

    1994-01-31

    Progress has been summarized in three papers: biaxial gas-pressure forming of a superplastic Al{sub 2}O{sub 3}/YTZP; mechanical properties of a 20 vol% SiC whisker-reinforced yttria-stabilized, tetragonal zirconia composite at elevated temperatures; and gas- pressure forming of ceramic sheet.

  14. Induced Ti magnetization at La0.7Sr0.3MnO3 and BaTiO3 interfaces

    Directory of Open Access Journals (Sweden)

    Yaohua Liu

    2016-04-01

    Full Text Available In artificial multiferroics hybrids consisting of ferromagnetic La0.7Sr0.3MnO3 (LSMO and ferroelectric BaTiO3 epitaxial layers, net Ti moments are found from polarized resonant soft x-ray reflectivity and absorption. The Ti dichroic reflectivity follows the Mn signal during the magnetization reversal, indicating exchange coupling between the Ti and Mn ions. However, the Ti dichroic reflectivity shows stronger temperature dependence than the Mn dichroic signal. Besides a reduced ferromagnetic exchange coupling in the interfacial LSMO layer, this may also be attributed to a weak Ti-Mn exchange coupling that is insufficient to overcome the thermal energy at elevated temperatures.

  15. Ternary ceramic alloys of Zr-Ce-Hf oxides

    Science.gov (United States)

    Becher, P.F.; Funkenbusch, E.F.

    1990-11-20

    A ternary ceramic alloy is described which produces toughening of zirconia and zirconia composites through the stress transformation from tetragonal phase to monoclinic phase. This alloy, having the general formula Ce[sub x]Hf[sub y]Zr[sub 1[minus]x[minus]y]O[sub 2], is produced through the addition of appropriate amounts of ceria and hafnia to the zirconia. Typically, improved toughness is achieved with about 5 to about 15 mol % ceria and up to about 40 mol % hafnia. The preparation of alloys of these compositions are given together with data as to the densities, tetragonal phase content, hardness and fracture toughness. The alloys are useful in preparing zirconia bodies as well as reinforcing ceramic composites. 1 fig.

  16. Polymorphic phase transition dependence of piezoelectric properties in (K0.5Na0.5)NbO3-(Bi0.5K0.5)TiO3 lead-free ceramics

    International Nuclear Information System (INIS)

    Du Hongliang; Zhou Wancheng; Luo Fa; Zhu Dongmei; Qu Shaobo; Li Ye; Pei Zhibin

    2008-01-01

    Lead-free ceramics (1 - x)(K 0.5 Na 0.5 )NbO 3 -x(Bi 0.5 K 0.5 )TiO 3 [(1 - x)KNN-xBKT] were synthesized by conventional solid-state sintering. The phase structure, microstructure and electrical properties of (1 - x)KNN-xBKT ceramics were investigated. At room temperature, the polymorphic phase transition (from the orthorhombic to the tetragonal phase) (PPT) was identified at x = 0.02 by the analysis of x-ray diffraction patterns and dielectric spectroscopy. Enhanced electrical properties (d 33 = 251 pC N -1 , k p = 0.49, k t = 0.50, ε 33 T / ε 0 =1260, tan δ = 0.03 and T C = 376 deg. C) were obtained in the ceramics with x = 0.02 owing to the formation of the PPT at 70 deg. C and the selection of an optimum poling temperature. The related mechanisms for high piezoelectric properties in (1 - x)KNN-xBKT (x = 0.02) ceramics were discussed. In addition, the results confirmed that the selection of the optimum poling temperature was an effective way to further improve the piezoelectric properties of KNN-based ceramics. The enhanced properties were comparable to those of hard Pb(Zr, Ti)O 3 ceramics and indicated that the (1 - x)KNN-xBKT (x = 0.02) ceramic was a promising lead-free piezoelectric candidate material for actuator and transducer applications

  17. X-ray diffraction, dielectric, and Raman spectroscopy studies of BaSrTiO{sub 3}-NaNbO{sub 3} ceramic

    Energy Technology Data Exchange (ETDEWEB)

    Abdessalem, L. Ben; Aydi, S.; Aydi, A.; Maalej, A.; Khemakhem, H. [Universite de Sfax, Laboratoire des Materiaux Multifonctionnels et Applications (LaMMA), Faculte des Sciences de Sfax (FSS), Sfax (Tunisia); Sassi, Z. [Laboratoire de Genie Electrique et Ferroelectricite (LGEF) de L' INSA de Lyon, Villeurbanne (France)

    2017-05-15

    Ba{sub 0.837}Sr{sub 0.093}Na{sub 0.07}Ti{sub 0.93}Nb{sub 0.07}O{sub 3} (BSNTN) ceramic was synthesized by the solid-state reaction at 1350 C for 3 h. The crystal structure, investigated by X-ray diffraction at room temperature, revealed a single-phase perovskite crystallizing with tetragonal P4mm group space. Dielectric properties were investigated as a function of applied frequency. The ferroelectric behavior has been confirmed by hysteresis investigation. The evolution of the Raman spectra was used to study the variations of the basic phase transition of BaTiO{sub 3}, at room temperature. It shows the introduction of a disorder in this composition, thus favoring a ferroelectric relaxor behavior. (orig.)

  18. Influences of PZT addition on phase formation and magnetic properties of perovskite Pb(Fe{sub 0.5}Nb{sub 0.5})O{sub 3}-based ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Amonpattaratkit, P. [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Jantaratana, P. [Department of Physics, Faculty of Science, Kasetsart University, Bangkok 10900 (Thailand); Ananta, S., E-mail: suponananta@yahoo.com [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

    2015-09-01

    In this work, the investigation of phase formation, crystal structure, microstructure, microchemical composition and magnetic properties of perovskite (1−x)PFN–xPZT (x=0.1–0.5) multiferroic ceramics derived from a combination of perovskite stabilizer PZT and a wolframite-type FeNbO{sub 4}B-site precursor was carried out by using a combination of X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) analyzer and vibrating sample magnetometer (VSM) techniques. The addition of PZT phase and its concentration have been found to have pronounced effects on the perovskite phase formation, densification, grain growth and magnetic properties of the sintered ceramics. XRD spectra from these ceramics reveal transformation of the (pseudo) cubic into the tetragonal perovskite structure. When increasing PZT content, the degree of perovskite phase formation and the tetragonality value of the ceramics increase gradually accompanied with the variation of cell volume, the M–H hysteresis loops, however, become narrower accompanied by the decrease of maximum magnetization (M{sub max}), remanent polarization (M{sub r}), and coercive field (H{sub C}). - Highlights: • Fabrication of PFN-PZT multiferroic ceramics from PZT and FeNbO{sub 4} precursors. • Effect of PZT content on phase transformation of PFN-PZT multiferroic ceramics. • Effect of PZT content on magnetic properties of PFN-PZT multiferroic ceramics.

  19. Effect of different surface treatments on bond strength, surface and microscopic structure of zirconia ceramic

    Directory of Open Access Journals (Sweden)

    Zeinab R. El-Shrkawy

    2016-06-01

    Conclusions: (1 Surface treatments of Y-TZP ceramic together with MDP primer and silane-coupling agent application improve the bond strength to resin cement. (2 Plasma-Silica coating and plasma-oxygen treatment, both are valuable methods that improve the bond strength of resin cement to Y-TZP ceramic. (3 Silica coating by plasma technology provides durable bond strength and can be a promising alternative pretreatment before silane application to enhance bonding with zirconia ceramic. (4 Tetragonal-monoclinic phase transformation had occurred in Y-TZP samples received both types of plasma treatment.

  20. Piezoelectric properties of electrospun nanofibers of BaTiO3

    International Nuclear Information System (INIS)

    Carvalho, L.F.R.M.; Melo, G.F.; Goncalves, A.M.; Eiras, J.A.; Bretas, R.E.S.

    2016-01-01

    BaTiO3 nanofibers were produced by the electrospinning method from a mixture of a solution of the precursors Ba (CH_3COO)_2 and [(CH_3)_2CHO]_4Ti in acetic acid and a solution of poly(vinylpyrrolidone) in ethanol. A voltage of 10 kV and a working distance of 4.6 cm were used for the electrospinning, at controlled room temperature and humidity of 21 °C and 60% respectively. Nanofibers as spun were dried in air on an air-circulating oven at 100 °C for one hour to remove residual solvent and were subsequently calcined at 750 °C during 2 h. The morphology, crystallographic structure and piezoelectric properties of the nanofibers were analyzed by scanning electron microscopy (SEM), X-ray angle (WAXS) and Piezoresponse Force Microscopy (PFM), respectively. The average diameter of the nanofibers was 414 nm with an aspect ratio of 40. By PFM, there was strong evidence that the nanofibers had piezoelectric activity. (author)

  1. Enhanced actuation performance of piezoelectric fiber composites induced by incorporated BaTiO3 nanoparticles in epoxy resin

    International Nuclear Information System (INIS)

    Wu, Mingliang; Yuan, Xi; Luo, Hang; Chen, Haiyan; Chen, Chao; Zhou, Kechao; Zhang, Dou

    2017-01-01

    Piezoelectric fiber composites (PFCs) have attracted much interest owing to their flexibility and toughness compared with conventional monolithic piezoceramic wafers. The free strain values and actuation property of PFCs strongly depend on the active electric field applied in Pb(Zr 1−x Ti x )O 3 (PZT) fibers. Reducing the dielectric constant mismatch between PZT fiber and the assembling epoxy resin would greatly increase the active electric field in PZT fiber. Therefore, BaTiO 3 (BT) nanoparticles were introduced into the epoxy resin to enhance the dielectric constant. Homogeneous dispersion of BT nanoparticles and tight adhesion with the epoxy resin were achieved through a surface modification by dopamine. The maximum dielectric constant of dopamine modified BT/epoxy (BT@Dop/epoxy) nanocomposites was 10.38 with 12 wt% BT@Dop content at 1 kHz. The maximum free strain of PFCs reached 1820 ppm with 6 wt% BT@Dop content, while PFCs assembled by pure epoxy showed 790 ppm at the same processing condition. The tip displacement of cantilever beam actuated by PFCs reached the peak of 19 mm at the resonance frequency with 6 wt% BT@Dop, which was improved by 90% comparing to PFCs with pure epoxy. - Highlights: • The effect of dielectric mismatch on effective electric field in piezoceramic fibers was explained by a model. • The dispersibility and adhesion of BaTiO 3 nanoparticles in epoxy was improved by the dopamine modification. • The actuation performance increased firstly and then decreased with adding BaTiO 3 nanoparticles. • The maximum free strain and displacement of cantilever beam were up to 1820 ppm and 19 mm, respectively.

  2. Barium Titanate Nanoparticles for Biomarker Applications

    International Nuclear Information System (INIS)

    Matar, O; Hondow, N S; Brydson, R M D; Milne, S J; Brown, A P; Posada, O M; Wälti, C; Saunders, M; Murray, C A

    2015-01-01

    A tetragonal crystal structure is required for barium titanate nanoparticles to exhibit the nonlinear optical effect of second harmonic light generation (SHG) for use as a biomarker when illuminated by a near-infrared source. Here we use synchrotron XRD to elucidate the tetragonal phase of commercially purchased tetragonal, cubic and hydrothermally prepared barium titanate (BaTiO 3 ) nanoparticles by peak fitting with reference patterns. The local phase of individual nanoparticles is determined by STEM electron energy loss spectroscopy (EELS), measuring the core-loss O K-edge and the Ti L 3 -edge energy separation of the t 2g , e g peaks. The results show a change in energy separation between the t 2g and e g peak from the surface and core of the particles, suggesting an intraparticle phase mixture of the barium titanate nanoparticles. HAADF-STEM and bright field TEM-EDX show cellular uptake of the hydrothermally prepared BaTiO 3 nanoparticles, highlighting the potential for application as biomarkers. (paper)

  3. Preparation and properties of highly porous, biomorphic YSZ ceramics

    International Nuclear Information System (INIS)

    Rambo, C.R.; Cao, J.; Sieber, H.

    2004-01-01

    Highly porous, biomorphic YSZ (yttria-stabilized zirconia) ceramics were manufactured by infiltration of zirconium-oxychloride (ZrOCl 2 ·8H 2 O) sol into biological template structures derived from rattan and pine wood. 3-5 mol% yttrium nitrate (Y(NO 3 ) 3 ·5H 2 O) was added to the sol to stabilize the tetragonal ZrO 2 phase. After vacuum-assisted infiltration, the specimens were pyrolysed at 800 deg. C in N 2 atmosphere. Repeated infiltrations and subsequent annealing in air at temperatures up to 1550 deg. C yields the burn out of the biocarbon template and resulted in the formation of biomorphous YSZ ceramics, which maintained the microstructural features of the biological preform. Depending on the type of the biological template as well as the processing parameters, biomorphic ZrO 2 ceramics with an unidirected pore morphology and a large variety of microstructures can be obtained

  4. Zirconia toughened ceramics for heat engine applications

    International Nuclear Information System (INIS)

    Rossi, G.A.; Blum, J.B.; Manwiller, K.E.; Knapp, C.E.

    1986-01-01

    Three classes of zirconia toughened ceramics (ZTC) were studied, i.e. Mg-PSZ (MgO-partially stabilized zirconia), Y-TZP (Y/sub 2/O/sub 3/-tetragonal zirconia polycrystals) and ZTA (zirconia toughened alumina). The main objective was to improve the high temperature strength and toughness, which are not satisfactory in the ''state of the art'' ZTC materials. Powders prepared by melting/rapid solidification and by chemical routes were used. The green parts were made by both dry and wet shape forming methods. Fine grained Mg-PSZ ceramics with unique microstructures were produced using the rapidly solidified powders. The Y-TZP materials were improved mainly through microstructure control and by addition of alpha alumina as a dispersed phase. Preliminary results on ZTA ceramics made with the rapidly solidified powders were also obtained. It is concluded that the Al/sub 2/O/sub 3//Y-TZP composites offer a good chance of meeting the program objectives

  5. Effect of texturing on polarization switching dynamics in ferroelectric ceramics

    Science.gov (United States)

    Zhukov, Sergey; Genenko, Yuri A.; Koruza, Jurij; Schultheiß, Jan; von Seggern, Heinz; Sakamoto, Wataru; Ichikawa, Hiroki; Murata, Tatsuro; Hayashi, Koichiro; Yogo, Toshinobu

    2016-01-01

    Highly (100),(001)-oriented (Ba0.85Ca0.15)TiO3 (BCT) lead-free piezoelectric ceramics were fabricated by the reactive templated grain growth method using a mixture of plate-like CaTiO3 and BaTiO3 particles. Piezoelectric properties of the ceramics with a high degree of texture were found to be considerably enhanced compared with the BCT ceramics with a low degree of texture. With increasing the Lotgering factor from 26% up to 94%, the piezoelectric properties develop towards the properties of a single crystal. The dynamics of polarization switching was studied over a broad time domain of 8 orders of magnitude and was found to strongly depend on the degree of orientation of the ceramics. Samples with a high degree of texture exhibited 2-3 orders of magnitude faster polarization switching, as compared with the ones with a low degree of texture. This was rationalized by means of the Inhomogeneous Field Mechanism model as a result of the narrower statistical distribution of the local electric field values in textured media, which promotes a more coherent switching process. The extracted microscopic parameters of switching revealed a decrease of the critical nucleus energy in systems with a high degree of texture providing more favorable switching conditions related to the enhanced ferroelectric properties of the textured material.

  6. Dynamics of ferroelectric nanodomains in BaTiO3 epitaxial thin films via piezoresponse force microscopy

    International Nuclear Information System (INIS)

    Pertsev, N A; Petraru, A; Kohlstedt, H; Waser, R; Bdikin, I K; Kiselev, D; Kholkin, A L

    2008-01-01

    Ferroelectric nanodomains were created in BaTiO 3 thin films by applying a voltage to a sharp conducting tip of a scanning force microscope (SFM). The films were epitaxially grown on SrRuO 3 -covered (001)-oriented SrTiO 3 substrates by a high-pressure sputtering. They appeared to be single-crystalline with the (001) crystallographic orientation relative to the substrate. Using the piezoresponse mode of the SFM to detect the out-of-plane film polarization, the domain sizes were measured as a function of the applied writing voltage and the pulse time. It was found that the time dependence of the domain diameter in a 60 nm thick BaTiO 3 film deviates significantly from the logarithmic law observed earlier in Pb(Zr 0.2 Ti 0.8 )O 3 (PZT) films. At a given writing time, the domain size increases nonlinearly with increasing applied voltage, in contrast to the linear behavior reported earlier for PZT films and LiNbO 3 single crystals. The dynamics of domain growth is analyzed theoretically taking into account the strong inhomogeneity of the external electric field in the film and the influence of the bottom electrode. It is shown that the observed writing time and voltage dependences of the domain size can be explained by the domain-wall creep in the presence of random-bond disorder

  7. STRUCTURAL CHARACTERISTICS & DIELECTRIC PROPERTIES OF TANTALUM OXIDE DOPED BARIUM TITANATE BASED MATERIALS

    Directory of Open Access Journals (Sweden)

    Md. Fakhrul Islam

    2013-01-01

    Full Text Available In this research, the causal relationship between the dielectric properties and the structural characteristics of 0.5 & 1.0 mole % Ta2O5 doped BaTiO3 based ceramic materials were investigated under different sintering conditions. Dielectric properties and microstructure of BaTio3 ceramics were significantly influenced by the addition of a small amount of Ta2O5. Dielectric properties were investigated by measuring the dielectric constant (k as a function of temperature and frequency. Percent theoretical density (%TD above 90 % was achieved for 0.5 and 1.0 mole %Ta2O5 doped BaTiO3. It was observed that the grain size decreased markedly above a doping concentration of 0.5 mole % Ta2O5. Although fine grain size down to 200 - 300 nm was attained, grain sizes in the range of 1-1.8µm showed the most alluring properties. The fine-grain quality and high density of the Ta2O5 doped BaTiO3 ceramic resulted in tenfold increase of dielectric constant. Stable value of dielectric constant as high as 13000 - 14000 was found in the temperature range of 55 to 80 °C, for 1.0 mole % Ta2O5 doped samples with corresponding shift of Curie point to ~82 °C. Experiments divulged that incorporation of a proper content of Ta2O5 in BaTiO3 could control the grain growth, shift the Curie temperature and hence significantly improve the dielectric property of the BaTiO3 ceramics.

  8. Dielectric and magnetic properties of Ba-, La- and Pb-doped Bi0.8Gd0.1M0.1Fe0.9Ti0.1O3 perovskite ceramics

    Directory of Open Access Journals (Sweden)

    Radheshyam Rai

    2014-04-01

    Full Text Available The multiferroic Bi0.8Gd0.1M0.1Fe0.9Ti0.1O3, (where M = Ba (DB, La (DL and Pb (DP has been synthesized by using solid-state reaction technique. Effects of Ba, La and Pb substitution on the structure, electrical and ferroelectric properties of Bi0.8Gd0.1M0.1Fe0.9Ti0.1O3 samples have been studied by performing X-ray diffraction, dielectric and magnetic measurements. The crystal structures of the ceramic samples have a tetragonal phase. The vibrating sample magnetometer (VSM measurement shows a significant change in the magnetic properties of Ba-doped Bi0.8Gd0.1M0.1Fe0.9Ti0.1O3 as compared to La- and Pb-doped ceramics. It is seen that coercive field (HC and remanent magnetization (MR increases with Ba-doped ceramics but decreases for La- and Pb-doped ceramics.

  9. On stoichiometry and intermixing at the spinel/perovskite interface in CoFe2O4/BaTiO3 thin films.

    Science.gov (United States)

    Tileli, Vasiliki; Duchamp, Martial; Axelsson, Anna-Karin; Valant, Matjaz; Dunin-Borkowski, Rafal E; Alford, Neil McN

    2015-01-07

    The performance of complex oxide heterostructures depends primarily on the interfacial coupling of the two component structures. This interface character inherently varies with the synthesis method and conditions used since even small composition variations can alter the electronic, ferroelectric, or magnetic functional properties of the system. The focus of this article is placed on the interface character of a pulsed laser deposited CoFe2O4/BaTiO3 thin film. Using a range of state-of-the-art transmission electron microscopy methodologies, the roles of substrate morphology, interface stoichiometry, and cation intermixing are determined on the atomic level. The results reveal a surprisingly uneven BaTiO3 substrate surface formed after the film deposition and Fe atom incorporation in the top few monolayers inside the unit cell of the BaTiO3 crystal. Towards the CoFe2O4 side, a disordered region extending several nanometers from the interface was revealed and both Ba and Ti from the substrate were found to diffuse into the spinel layer. The analysis also shows that within this somehow incompatible composite interface, a different phase is formed corresponding to the compound Ba2Fe3Ti5O15, which belongs to the ilmenite crystal structure of FeTiO3 type. The results suggest a chemical activity between these two oxides, which could lead to the synthesis of complex engineered interfaces.

  10. Sol-gel dip coating of yttria-stabilized tetragonal zirconia dental ceramic by aluminosilicate nanocomposite as a novel technique to improve the bonding of veneering porcelain.

    Science.gov (United States)

    Madani, Azamsadat; Nakhaei, Mohammadreza; Karami, Parisa; Rajabzadeh, Ghadir; Salehi, Sahar; Bagheri, Hossein

    2016-01-01

    The aim of this in vitro study was to evaluate the effect of silica and aluminosilicate nanocomposite coating of zirconia-based dental ceramic by a sol-gel dip-coating technique on the bond strength of veneering porcelain to the yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) in vitro. Thirty Y-TZP blocks (10 mm ×10 mm ×3 mm) were prepared and were assigned to four experimental groups (n=10/group): C, without any further surface treatment as the control group; S, sandblasted using 110 μm alumina powder; Si, silica sol dip coating + calcination; and Si/Al, aluminosilicate sol dip coating + calcination. After preparing Y-TZP samples, a 3 mm thick layer of the recommended porcelain was fired on the coated Y-TZP surface. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray analysis were used to characterize the coating and the nature of the bonding between the coating and zirconia. To examine the zirconia-porcelain bond strength, a microtensile bond strength (μTBS) approach was chosen. FT-IR study showed the formation of silica and aluminosilicate materials. XRD pattern showed the formation of new phases consisting of Si, Al, and Zr in coated samples. SEM showed the formation of a uniform coating on Y-TZP samples. Maximum μTBS values were obtained in aluminosilicate samples, which were significantly increased compared to control and sandblasted groups (P=0.013 and Pcoating can be considered as a convenient, less expensive reliable method for improving the bond strength between dental Y-TZP ceramics and veneering porcelain.

  11. Quantitative analysis of UV excitation bands for red emissions in Pr3+-doped CaTiO3, SrTiO3 and BaTiO3 phosphors by peak fitting

    International Nuclear Information System (INIS)

    Fujiwara, Rei; Sano, Hiroyuki; Shimizu, Mikio; Kuwabara, Makoto

    2009-01-01

    A quantitative spectral analysis of the ultraviolet (UV) broad excitation bands, which are located in the range 300-400 nm, for red emissions at around 610 nm in Pr-doped CaTiO 3 , SrTiO 3 :Al and BaTiO 3 :Mg phosphors has been carried out using a peak fitting technique. The obtained results demonstrate that the UV broad band of CaTiO 3 :Pr consists of four primary excitation bands centered around 330, 335, 365 and 380 nm and those of both SrTiO 3 :Al and BaTiO 3 :Mg consist of three primary bands centered around 310, 345 and 370 nm. Based on the behavior patterns and the values of the respective primary excitation bands' parameters, i.e. center gravity (λ top ), maximum height (I max ) and full-width at half-maximum (FWHM), the UV-to-red relaxation processes in these titanate phosphors can be explained to be essentially the same, except for the existence of an additional relaxation pathway via electron-trap states in CaTiO 3 :Pr, which gives a characteristic shape of its UV excitation spectrum in the wavelength range of >360 nm

  12. Effect of Ca2+ Ions on Electrical Properties of Ba1-x Ca x Ti0.90Sn0.10O3-0.05Y2O3 Ceramics

    Science.gov (United States)

    Chen, Zhi-hui; Li, Zhi-wei; Ding, Jian-ning; Zhao, Tian-xiang; Qiu, Jian-hua; Zhu, Ke-qian; Xu, Jiu-jun; Zhang, Bing

    2018-03-01

    Ba1-x Ca x Ti0.90Sn0.10O3-0.05Y2O3 (BCTSY) lead-free piezoceramics with x = 0.02 to 0.10 have been fabricated by solid-state sintering method at 1420°C. The effects of Ca2+ ions on the microstructure and electrical properties of the samples were studied. X-ray diffraction analysis showed that all samples possessed pure perovskite structure with Ca2+ ions diffused into the matrix lattice. The rhombohedral phase and tetragonal phase coexisted in the composition range of 0.02 ceramic became more homogeneous with addition of Ca2+ ions, and the average grain size of the samples decreased from 97 μm (x = 0.02) to 18 μm (x = 0.10). Addition of Ca2+ remarkably improved the piezoelectric properties, enhanced the dielectric frequency dispersion, and increased the Curie temperature of the ceramics. The piezoelectric properties of the ceramics were optimized at x = 0.04 with d 33 and K p values of 579 pC/N and 52.7%, respectively.

  13. Effect of grain size on structural and dielectric properties of barium titanate piezoceramics synthesized by high energy ball milling

    Science.gov (United States)

    Verma, Narendra Kumar; Patel, Sandeep Kumar Singh; Kumar, Dinesh; Singh, Chandra Bhal; Singh, Akhilesh Kumar

    2018-05-01

    We have investigated the effect of sintering temperature on the densification behaviour, grain size, structural and dielectric properties of BaTiO3 ceramics, prepared by high energy ball milling method. The Powder x-ray diffraction reveals the tetragonal structure with space group P4mm for all the samples. The samples were sintered at four different temperatures, (T = 900°C, 1000°C, 1100°C, 1200°C and 1300°C). Density increased with increasing sintering temperature, reaching up to 97% at 1300°C. A grain growth was observed with increasing sintering temperature. Impedance analyses of the sintered samples at various temperatures were performed. Increase in dielectric constant and Curie temperature is observed with increasing sintering temperature.

  14. Tetragonal CuO: End member of the 3d transition metal monoxides

    NARCIS (Netherlands)

    Siemons, W.; Koster, Gertjan; Blank, David H.A.; Hammond, Robert H.; Geballe, Theodore H.; Beasley, Malcolm R.

    2009-01-01

    Monoclinic CuO is anomalous both structurally as well as electronically in the 3d transition metal oxide series. All the others have the cubic rocksalt structure. Here we report the synthesis and electronic property determination of a tetragonal (elongated rocksalt) form of CuO created using an

  15. PREFACE: 3rd International Congress on Ceramics (ICC3)

    Science.gov (United States)

    Niihara, Koichi; Ohji, Tatsuki; Sakka, Yoshio

    2011-10-01

    Early in 2005, the American Ceramic Society, the European Ceramic Society and the Ceramic Society of Japan announced a collaborative effort to provide leadership for the global ceramics community that would facilitate the use of ceramic and glass materials. That effort resulted in an agreement to organize a new biennial series of the International Congress on Ceramics, convened by the International Ceramic Federation (ICF). In order to share ideas and visions of the future for ceramic and glass materials, the 1st International Congress on Ceramics (ICC1) was held in Canada, 2006, under the organization of the American Ceramic Society, and the 2nd Congress (ICC2) was held in Italy, 2008, hosted by the European Ceramic Society. Organized by the Ceramic Society of Japan, the 3rd Congress (ICC3) was held in Osaka, Japan, 14-18 November 2010. Incorporating the 23rd Fall Meeting of the Ceramic Society of Japan and the 20th Iketani Conference, ICC3 was also co-organized by the Iketani Science and Technology Foundation, and was endorsed and supported by ICF, Asia-Oceania Ceramic Federation (AOCF) as well as many other organizations. Following the style of the previous two successful Congresses, the program was designed to advance ceramic and glass technologies to the next generation through discussion of the most recent advances and future perspectives, and to engage the worldwide ceramics community in a collective effort to expand the use of these materials in both conventional as well as new and exciting applications. ICC3 consisted of 22 voluntarily organized symposia in the most topical and essential themes of ceramic and glass materials, including Characterization, design and processing technologies Electro, magnetic and optical ceramics and devices Energy and environment related ceramics and systems Bio-ceramics and bio-technologies Ceramics for advanced industry and safety society Innovation in traditional ceramics It also contained the Plenary Session and the

  16. Characterization of a Diamond Ground Y-TZP and Reversion of the Tetragonal to Monoclinic Transformation.

    Science.gov (United States)

    Candido, L M; Fais, Lmg; Ferreira, E B; Antonio, S G; Pinelli, Lap

    To characterize the surface of an yttria-stabilized zirconia (Y-TZP) ceramic after diamond grinding in terms of its crystalline phase, morphology, mean roughness (Ra), and wettability as well as to determine a thermal treatment to reverse the resulting tetragonal to monoclinic (t-m) transformation. Y-TZP specimens were distributed into different groups according to the actions (or no action) of grinding and irrigation. Grinding was accomplished using a diamond stone at a low speed. The samples were characterized by x-ray diffraction (XRD), scanning electron microscopy, goniometry, and profilometry. In situ high-temperature XRD was used to determine an annealing temperature to reverse the t-m transformation. Ra was submitted to the Kruskal-Wallis test, followed by the Dunn test (α=0.05). The volume fraction of the monoclinic phase and contact angle were submitted to one-way analysis of variance, followed by the Tukey test (α=0.05). Monoclinic zirconia was observed on the surface of samples after dry and wet grinding with a diamond stone. The volume fraction of the monoclinic phase was smaller on the dry ground samples (3.6%±0.3%) than on the wet ground samples (5.6%±0.3%). High-temperature XRD showed reversion of the t-m phase transformation, which started at 700°C and completed at 800°C in a conventional oven. Grinding with a diamond stone partially transformed the crystalline phase on the surface of a Y-TZP ceramic from tetragonal to monoclinic zirconia while simultaneously increasing the surface roughness and wettability. The t-m transformation could be reversed by heat treatment at 800°C or 900°C for 60 minutes or 1000°C for 30 minutes.

  17. Preparation and properties of highly porous, biomorphic YSZ ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Rambo, C.R.; Cao, J.; Sieber, H

    2004-10-15

    Highly porous, biomorphic YSZ (yttria-stabilized zirconia) ceramics were manufactured by infiltration of zirconium-oxychloride (ZrOCl{sub 2}{center_dot}8H{sub 2}O) sol into biological template structures derived from rattan and pine wood. 3-5 mol% yttrium nitrate (Y(NO{sub 3}){sub 3}{center_dot}5H{sub 2}O) was added to the sol to stabilize the tetragonal ZrO{sub 2} phase. After vacuum-assisted infiltration, the specimens were pyrolysed at 800 deg. C in N{sub 2} atmosphere. Repeated infiltrations and subsequent annealing in air at temperatures up to 1550 deg. C yields the burn out of the biocarbon template and resulted in the formation of biomorphous YSZ ceramics, which maintained the microstructural features of the biological preform. Depending on the type of the biological template as well as the processing parameters, biomorphic ZrO{sub 2} ceramics with an unidirected pore morphology and a large variety of microstructures can be obtained.

  18. Synthesis of Barium Titanate from Titanyl Acylate Precursor by Sol-precipitate Method

    International Nuclear Information System (INIS)

    Thandar Win; Kyaw Naing; Khin Mar Tun

    2008-03-01

    Nanometersize barium titanates (BaTiO3:BT) powders can be obtained by sol-precipitate method in the presence of polyoxyethylene (20) sorbiton monooleate (Tween-80) as a polymeric surface modifier in a strong alkaline solution (pH > 13). FT-IR, TG/DTA, SEM and XRD were used to investigate the effects of the surfactant influence on the morphology of the obtained BaTiO3 powders. With adding surfactant, a slower rate of hydrolyzation is observed and the rate of condensation is slower. The addition of Tween-80 surfactant in general leads to the formation of smaller particle size of BaTi)3 (70-100 nm). Without adding surfactant, larger particle size of BaTiO3 (100-200 nm) was obtained. The nanometersize BaTiO3 powders were readily sintered at 1000-1200C. Raman-active modes of tetragonal phase BT were detected from Raman spectra of BaTiO3 between 800 0 C to 1200 0 C.

  19. Structural Characteristics & Dielectric Properties of Tantalum Oxide Doped Barium Titanate Based Materials

    Directory of Open Access Journals (Sweden)

    Rubayyat Mahbub

    2012-11-01

    Full Text Available In this research, the causal relationship between the dielectric properties and the structural characteristics of 0.5 & 1.0 mol% Ta2O5 doped BaTiO3 based ceramic materials were investigated under different sintering conditions. Dielectric properties and microstructure of BaTio3 ceramics were significantly influenced by the addition of a small amount of Ta2O5. Dielectric properties were investigated by measuring the dielectric constant (k as a function of temperature and frequency. Percent theoretical density (%TD above 90% was achieved for 0.5 and 1.0 mol% Ta2O5 doped BaTiO3. It was observed that the grain size decreased markedly above a doping concentration of 0·5 mol% Ta2O5. Although fine grain size down to 200-300nm was attained, grain sizes in the range of 1-1.8µm showed the most alluring properties. The fine-grain quality and high density of the Ta2O5 doped BaTiO3 ceramic resulted in tenfold increase of dielectric constant. Stable value of dielectric constant as high as 13000-14000 was found in the temperature range of  55 to 80°C, for 1.0 mol% Ta2O5 doped samples with corresponding shift of Curie point to ~82°C. Experiments divulged that incorporation of a proper content of Ta2O5 in BaTiO3 could control the grain growth, shift the Curie temperature and hence significantly improve the dielectric property of the BaTiO3 ceramics.

  20. Fabrication and electrical investigations of Pb-doped BaTiO{sub 3} ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Sareecha, N., E-mail: nsareecha@hotmail.com [Laboratory of Physical Chemistry, Department of Chemistry, Islamia University of Bahawalpur (Pakistan); Shah, W.A. [Glass and Ceramics Research Centre, PCSIR Laboratories Complex, Ferozpur Road, Lahore 54600 (Pakistan); Maqsood, A. [Nano Scale Physics Laboratory, Department of Physics, Air University, PAF Complex E-9, Islamabad (Pakistan); Anis-ur-Rehman, M. [Applied Thermal Physics Laboratory, COMSATS Institute of Information and Technology, Park Road, Islamabad 44000 (Pakistan); Latif Mirza, M. [Laboratory of Physical Chemistry, Department of Chemistry, Islamia University of Bahawalpur (Pakistan)

    2017-06-01

    Electrical properties of Pb doped BaTiO{sub 3}; PBT are investigated in the wide range of temperatures (40–700 °C) at 1 kHz frequency. PBT ceramics were fabricated through solid state sintering method. Pre fired BaTiO{sub 3} prepared with Ba/Ti molar ratio of 0.98 was doped with PbCO{sub 3} (<1 mole %). XRD patterns indicated perovskite phase with tetragonal structures (P4mm). Morphological studies (SEM) revealed grain development with increasing lead contents. With lead doping and its variation, Curie temperature (T{sub C}) was shifted from 120 to 200 °C with broad dielectric constant peaks and dielectric anomalies with relaxor behavior were observed. Resistivity decreased with increasing temperature, all specimens showed semiconductor behavior with negative temperature coefficient of resistivity (NTCR) characteristics. Mobility of electrons increased with thermal activation due to hopping of charge carriers from one site to another. Ohmic conductivities and associated activation energies were evaluated by impedance spectroscopy. Conductivity followed the Arrhenius law with E{sub a} = 1.187–1.169 eV which can be attributed to the ionic conduction owning to doubly ionized oxygen vacancies. Well-defined hysteresis P-E loops measured at room temperature depicted ferroelectric properties of the materials. - Graphical abstract: Temperature dependence of dielectric constant (Ɛ′) and resistivity (ρ) for pure and Pb-doped BaTiO{sub 3} ceramics at 1 k Hz frequency. - Highlights: • Pb-doped BaTiO{sub 3}ceramics were fabricated through solid state sintering. • Electrical properties were studied at the temperatures 40–700 °C at 1 kHz. • Specimens showed negative temperature coefficient of resistivity characteristics. • Conductivity followed the Arrhenius law with E{sub a} = 1.187–1.169 eV. • Ionic conduction was supposed to be responsible for conduction process.

  1. Origin of thermally stable ferroelectricity in a porous barium titanate thin film synthesized through block copolymer templating

    Directory of Open Access Journals (Sweden)

    Norihiro Suzuki

    2017-07-01

    Full Text Available A porous barium titanate (BaTiO3 thin film was chemically synthesized using a surfactant-assisted sol-gel method in which micelles of amphipathic diblock copolymers served as structure-directing agents. In the Raman spectrum of the porous BaTiO3 thin film, a peak corresponding to the ferroelectric tetragonal phase was observed at around 710 cm−1, and it remained stable at much higher temperature than the Curie temperature of bulk single-crystal BaTiO3 (∼130 °C. Measurements revealed that the ferroelectricity of the BaTiO3 thin film has high thermal stability. By analyzing high-resolution transmission electron microscope images of the BaTiO3 thin film by the fast Fourier transform mapping method, the spatial distribution of stress in the BaTiO3 framework was clearly visualized. Careful analysis also indicated that the porosity in the BaTiO3 thin film introduced anisotropic compressive stress, which deformed the crystals. The resulting elongated unit cell caused further displacement of the Ti4+ cation from the center of the lattice. This displacement increased the electric dipole moment of the BaTiO3 thin film, effectively enhancing its ferro(piezoelectricity.

  2. Production of BaTiO3 nanoparticles through the sol-gel route using humic substances from river water

    International Nuclear Information System (INIS)

    Lima, C.H.S.; Lima, S.S.S.; Gomes, M.A.; Novaes, S.M.V.; Macedo, Z.S.

    2016-01-01

    A new route of synthesis, low cost and low environmental impact, has been developed for the production of barium titanate (BaTiO3). This material is widely used in the electronics industry due to its dielectric properties, ferroelectric and piezoelectric. Its crystal structure of perovskite type also has the ability to host dopants of different sizes, allowing a wide variety of ions is accommodated in BaTiO3 structure. The synthesis route proposed in this paper explores the complexation capacity of natural organic matter (NOM). Parameters such as concentration, pH and calcination temperature were investigated during production, with the aim of developing a simple, efficient and low energy cost procedure. Samples produced with concentration 0.5 g / ml showed a single phase after calcination at 1200 °C for 5 h. The crystallite size was estimated by Scherrer equation around 28 nm and the particle size, determined by scanning electron microscopy (SEM-FEG) was from 80 to 180nm order. The sample produced also presented heterogeneous morphology with spherical particles, rods and needles. (author)

  3. Compositional Design of Dielectric, Ferroelectric and Piezoelectric Properties of (K, NaNbO3 and (Ba, Na(Ti, NbO3 Based Ceramics Prepared by Different Sintering Routes

    Directory of Open Access Journals (Sweden)

    José A. Eiras

    2016-03-01

    Full Text Available Lead free piezoelectric materials are being intensively investigated in order to substitute lead based ones, commonly used in many different applications. Among the most promising lead-free materials are those with modified NaNbO3, such as (K, NaNbO3 (KNN and (Ba, Na(Ti, NbO3 (BTNN families. From a ceramic processing point of view, high density single phase KNN and BTNN ceramics are very difficult to sinter due to the volatility of the alkaline elements, the narrow sintering temperature range and the anomalous grain growth. In this work, Spark Plasma Sintering (SPS and high-energy ball milling (HEBM, following heat treatments (calcining and sintering, in oxidative (O2 atmosphere have been used to prepare single phase highly densified KNN (“pure” and Cu2+ or Li1+ doped, with theoretical densities ρth > 97% and BTNN ceramics (ρth - 90%, respectively. Using BTTN ceramics with a P4mm perovskite-like structure, we showed that by increasing the NaNbO3 content, the ferroelectric properties change from having a relaxor effect to an almost “normal” ferroelectric character, while the tetragonality and grain size increase and the shear piezoelectric coefficients (k15, g15 and d15 improve. For KNN ceramics, the results reveal that the values for remanent polarization as well as for most of the coercive field are quite similar among all compositions. These facts evidenced that Cu2+ may be incorporated into the A and/or B sites of the perovskite structure, having both hardening and softening effects.

  4. Compositional Design of Dielectric, Ferroelectric and Piezoelectric Properties of (K, Na)NbO3 and (Ba, Na)(Ti, Nb)O3 Based Ceramics Prepared by Different Sintering Routes

    Science.gov (United States)

    Eiras, José A.; Gerbasi, Rosimeire B. Z.; Rosso, Jaciele M.; Silva, Daniel M.; Cótica, Luiz F.; Santos, Ivair A.; Souza, Camila A.; Lente, Manuel H.

    2016-01-01

    Lead free piezoelectric materials are being intensively investigated in order to substitute lead based ones, commonly used in many different applications. Among the most promising lead-free materials are those with modified NaNbO3, such as (K, Na)NbO3 (KNN) and (Ba, Na)(Ti, Nb)O3 (BTNN) families. From a ceramic processing point of view, high density single phase KNN and BTNN ceramics are very difficult to sinter due to the volatility of the alkaline elements, the narrow sintering temperature range and the anomalous grain growth. In this work, Spark Plasma Sintering (SPS) and high-energy ball milling (HEBM), following heat treatments (calcining and sintering), in oxidative (O2) atmosphere have been used to prepare single phase highly densified KNN (“pure” and Cu2+ or Li1+ doped), with theoretical densities ρth > 97% and BTNN ceramics (ρth ~ 90%), respectively. Using BTTN ceramics with a P4mm perovskite-like structure, we showed that by increasing the NaNbO3 content, the ferroelectric properties change from having a relaxor effect to an almost “normal” ferroelectric character, while the tetragonality and grain size increase and the shear piezoelectric coefficients (k15, g15 and d15) improve. For KNN ceramics, the results reveal that the values for remanent polarization as well as for most of the coercive field are quite similar among all compositions. These facts evidenced that Cu2+ may be incorporated into the A and/or B sites of the perovskite structure, having both hardening and softening effects. PMID:28773304

  5. The effect of inter-granular constraints on the response of polycrystalline piezoelectric ceramics at the surface and in the bulk

    DEFF Research Database (Denmark)

    Hossain, Mohammad J.; Wang, Zhiyang; Khansur, Neamul H.

    2016-01-01

    V) synchrotron X-ray diffraction with in situ electric fields. The results show that for tetragonal PZT at a maximum electric field of 2.8 kV/mm, the electric-field-induced lattice strain (ε111) is 20% higher at the surface than in the bulk, and non-180° ferroelectric domain texture (as indicated......The electro-mechanical coupling mechanisms in polycrystalline ferroelectric materials, including a soft PbZrxTi1−xO3 (PZT) and lead-free 0.9375(Bi1/2Na1/2)TiO3-0.0625BaTiO3 (BNT-6.25BT), have been studied using a surface sensitive low-energy (12.4 keV) and bulk sensitive high-energy (73 ke...... by the intensity ratio I002/I200) is 16% higher at the surface. In the case of BNT-6.25BT, which is pseudo-cubic up to fields of 2 kV/mm, lattice strains, ε111 and ε200, are 15% and 20% higher at the surface, while in the mixed tetragonal and rhombohedral phases at 5 kV/mm, the domain texture indicated...

  6. Magnetoelectric coupling in multiferroic BaTiO3-CoFe2O4 composite nanofibers via electrospinning

    Science.gov (United States)

    Fu, Bi; Lu, Ruie; Gao, Kun; Yang, Yaodong; Wang, Yaping

    2015-07-01

    Magnetoelectric (ME) coupling in Pb-based multiferroic composites has been widely investigated due to the excellent piezoelectric property of lead zirconate titanate (PZT). In this letter, we report a strategy to create a hybrid Pb-free ferroelectric and ferromagnetic material and detect its ME coupling at the nanoscale. Hybrid Pb-free multiferroic BaTiO3-CoFe2O4 (BTO-CFO) composite nanofibers (NFs) were generated by sol-gel electrospinning. The perovskite structure of BTO and the spinel structure of CFO nanograins were homogenously distributed in the composite NFs and verified by bright-field transmission electron microscopy observations along the perovskite [111] zone axis. Multiferroicity was confirmed by amplitude-voltage butterfly curves and magnetic hysteresis loops. ME coupling was observed in terms of a singularity on a dM/dT curve at the ferroelectric Curie temperature (TC) of BaTiO3. The lateral ME coefficient was investigated by the evolution of the piezoresponse under an external magnetic field of 1000 Oe and was estimated to be α31 =0.78× 104 \\text{mV cm}-1 \\text{Oe}-1 . These findings could enable the creation of nanoscale Pb-free multiferroic composite devices.

  7. Direct detection of cysteine using functionalized BaTiO3 nanoparticles film based self-powered biosensor.

    Science.gov (United States)

    Selvarajan, Sophia; Alluri, Nagamalleswara Rao; Chandrasekhar, Arunkumar; Kim, Sang-Jae

    2017-05-15

    Simple, novel, and direct detection of clinically important biomolecules have continuous demand among scientific community as well as in market. Here, we report the first direct detection and facile fabrication of a cysteine-responsive, film-based, self-powered device. NH 2 functionalized BaTiO 3 nanoparticles (BT-NH 2 NPs) suspended in a three-dimensional matrix of an agarose (Ag) film, were used for cysteine detection. BaTiO 3 nanoparticles (BT NPs) semiconducting as well as piezoelectric properties were harnessed in this study. The changes in surface charge properties of the film with respect to cysteine concentrations were determined using a current-voltage (I-V) technique. The current response increased with cysteine concentration (linear concentration range=10µM-1mM). Based on the properties of the composite (BT/Ag), we created a self-powered cysteine sensor in which the output voltage from a piezoelectric nanogenerator was used to drive the sensor. The potential drop across the sensor was measured as a function of cysteine concentrations. Real-time analysis of sensor performance was carried out on urine samples by non-invasive method. This novel sensor demonstrated good selectivity, linear concentration range and detection limit of 10µM; acceptable for routine analysis. Copyright © 2016 Elsevier B.V. All rights reserved.

  8. Fracture-dissociation of ceramic liner.

    Science.gov (United States)

    Hwang, Sung Kwan; Oh, Jin-Rok; Her, Man Seung; Shim, Young Jun; Cho, Tae Yeun; Kwon, Sung Min

    2008-08-01

    The use of BIOLOX delta ceramic (CeramTec AG, Plochingen, Germany) has been increasing. This ceramic prevents cracking by restraining the phase transformation due to the insertion of nano-sized, yttria-stabilized tetragonal zirconia into the alumina matrix. This restrains the progress of cracking through the formation of platelet-like crystal or whiskers due to the addition of an oxide additive. We observed a case of BIOLOX delta ceramic liner (CeramTec AG) rim fracture 4 months postoperatively. Radiographs showed that the ceramic liner was subluxated from the acetabular cup. Scratches on the acetabular cup and femoral neck were seen, and the fracture was visible on the rim of the liner. Under electron microscope, metal particle coatings from the ceramic liner were identified. The ceramic liner, fracture fragments, and adjacent tissues were removed and replaced with a ceramic liner and femoral head of the same size and design. We believe the mechanism of the fracture-dissociation of the ceramic liner in this case is similar to a case of separation of the ceramic liner from the polyethylene shell in a sandwich-type ceramic-ceramic joint. To prevent ceramic liner fracture-dissociation, the diameter of the femoral neck needs to be decreased in a new design, while the diameter of the femoral head needs to be increased to ensure an increase in range of motion.

  9. Giant strain with low cycling degradation in Ta-doped [Bi_1_/_2(Na_0_._8K_0_._2)_1_/_2]TiO_3 lead-free ceramics

    International Nuclear Information System (INIS)

    Liu, Xiaoming; Tan, Xiaoli

    2016-01-01

    Non-textured polycrystalline [Bi_1_/_2(Na_0_._8K_0_._2)_1_/_2](Ti_1_−_xTa_x)O_3 ceramics are fabricated and their microstructures and electrical properties are characterized. Transmission electron microscopy reveals the coexistence of the rhombohedral R3c and tetragonal P4bm phases in the form of nanometer-sized domains in [Bi_1_/_2(Na_0_._8K_0_._2)_1_/_2]TiO_3 with low Ta concentration. When the composition is x = 0.015, the electrostrain is found to be highly asymmetric under bipolar fields of ±50 kV/cm. A very large value of 0.62% is observed in this ceramic, corresponding to a large-signal piezoelectric coefficient d_3_3* of 1240 pm/V (1120 pm/V under unipolar loading). These values are greater than most previously reported lead-free polycrystalline ceramics and can even be compared with some lead-free piezoelectric single crystals. Additionally, this ceramic displays low cycling degradation; its electrostrain remains above 0.55% even after undergoing 10 000 cycles of ±50 kV/cm bipolar fields at 2 Hz. Therefore, Ta-doped [Bi_1_/_2(Na_0_._8K_0_._2)_1_/_2]TiO_3 ceramics show great potential for large displacement devices.

  10. Sonochemically assisted hollow/solid BaTiO3:Dy3+ microspheres and their applications in effective detection of latent fingerprints and lip prints

    Directory of Open Access Journals (Sweden)

    M. Dhanalakshmi

    2017-03-01

    Full Text Available Nanostructured materials find potential benefits for surface-based science such as latent fingerprints (LFPs and lip print detection on porous and non-porous surfaces. To encounter the drawbacks viz. low sensitivity, high background hindrance, complicated procedure and high toxicity associated with traditional fluorescent powders were resolved by using hollow/solid BaTiO3:Dy3+ (1–5 mol % microspheres. The visualization of LFPs stained by the optimized BaTiO3:Dy3+ (2 mol % hollow/solid microspheres exhibits well-defined ridge patterns with high sensitivity, low background hindrance, high efficiency and low toxicity on various surfaces. The powder X-ray diffraction results revealed the body centered cubic phase of the prepared samples. The emission spectra exhibit intensive peaks at ∼480, 575, and 637 nm, which were attributed to transitions 4F9/2→6HJ (J = 15/2, 13/2, 11/2 of Dy3+ ions, respectively. Surface morphologies were extensively studied with different sonication times and concentrations of the used barbituric acid. The Commission International De I-Eclairage (CIE and Correlated Color Temperature (CCT analyses revealed that the present phosphor is highly useful for the fabrication of white light emitting diodes.

  11. Synthesis and crystallization behavior of 3 mol% yttria stabilized tetragonal zirconia polycrystals (3Y-TZP) nanosized powders prepared using a simple co-precipitation process

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, Yu-Wei [Graduate Institute of Applied Science, National Kaohsiung University of Applied Sciences, 415 Chien-Kung Road, Kaohsiung 80782, Taiwan (China); Yang, Ko-Ho, E-mail: yangkoho@cc.kuas.edu.tw [Graduate Institute of Applied Science, National Kaohsiung University of Applied Sciences, 415 Chien-Kung Road, Kaohsiung 80782, Taiwan (China); Department of Mold and Die Engineering, National Kaohsiung University of Applied Sciences, 415 Chien-Kung Road, Kaohsiung 80782, Taiwan (China); Chang, Kuo-Ming [Department of Mechanical Engineering, National Kaohsiung University of Applied Sciences, 415 Chien-Kung Road, Kaohsiung 80782, Taiwan (China); Dental Materials Research Center, National Kaohsiung University of Applied Sciences, 415 Chien-Kung Road, Kaohsiung 80782, Taiwan (China); Yeh, Sung-Wei [Metal Industries Research and Development Centre, 1001 Kaohsiung Highway, Kaohsiung 811, Taiwan (China); Wang, Moo-Chin, E-mail: mcwang@kmu.edu.tw [Department of Fragrance and Cosmetics Science, Kaohsiung Medical University, 100, Shihchuan 1st Road, Kaohsiung 80728, Taiwan (China)

    2011-06-16

    Highlights: > The thermal behavior of 3Y-TZP precursor powders had been investigated. > The crystallization behavior of 3Y-TZP nanopowders had been investigated. > The activation energy for crystallization of tetragonal ZrO{sub 2} was obtained. > The growth morphology parameter n is approximated as 2.0. > The crystallites show a plate-like morphology. - Abstract: The synthesis and crystallization behavior of 3 mol% yttria stabilized tetragonal zirconia polycrystals (3Y-TZP) nanopowders prepared using a simple co-precipitation process at 348 K and pH = 7 were investigated using differential scanning calorimetry/thermogravimetry (DSC/TG), an X-ray diffractometer (XRD), the Raman spectra, transmission electron microscopy (TEM), selected area electron diffraction (SAED), and an energy dispersive spectrometer (EDS). The activation energy of tetragonal ZrO{sub 2} crystallization from 3Y-TZP freeze-dried precursor powders using a non-isothermal method, namely, 169.2 {+-} 21.9 kJ mol{sup -1}, was obtained. The growth morphology parameter n was approximated as 2.0, which indicated that it had a plate-like morphology. The XRD, Raman spectra, and SAED patterns showed that the phase of the tetragonal ZrO{sub 2} was maintained at 1273 K. The crystallite size of 3Y-TZP freeze-dried precursor powders calcined at 1273 K for 5 min was 21.3 nm.

  12. Synthesis and crystallization behavior of 3 mol% yttria stabilized tetragonal zirconia polycrystals (3Y-TZP) nanosized powders prepared using a simple co-precipitation process

    International Nuclear Information System (INIS)

    Hsu, Yu-Wei; Yang, Ko-Ho; Chang, Kuo-Ming; Yeh, Sung-Wei; Wang, Moo-Chin

    2011-01-01

    Highlights: → The thermal behavior of 3Y-TZP precursor powders had been investigated. → The crystallization behavior of 3Y-TZP nanopowders had been investigated. → The activation energy for crystallization of tetragonal ZrO 2 was obtained. → The growth morphology parameter n is approximated as 2.0. → The crystallites show a plate-like morphology. - Abstract: The synthesis and crystallization behavior of 3 mol% yttria stabilized tetragonal zirconia polycrystals (3Y-TZP) nanopowders prepared using a simple co-precipitation process at 348 K and pH = 7 were investigated using differential scanning calorimetry/thermogravimetry (DSC/TG), an X-ray diffractometer (XRD), the Raman spectra, transmission electron microscopy (TEM), selected area electron diffraction (SAED), and an energy dispersive spectrometer (EDS). The activation energy of tetragonal ZrO 2 crystallization from 3Y-TZP freeze-dried precursor powders using a non-isothermal method, namely, 169.2 ± 21.9 kJ mol -1 , was obtained. The growth morphology parameter n was approximated as 2.0, which indicated that it had a plate-like morphology. The XRD, Raman spectra, and SAED patterns showed that the phase of the tetragonal ZrO 2 was maintained at 1273 K. The crystallite size of 3Y-TZP freeze-dried precursor powders calcined at 1273 K for 5 min was 21.3 nm.

  13. Structural and dielectric characterization of praseodymium-modified lead titanate ceramics synthesized by the OPM route

    Energy Technology Data Exchange (ETDEWEB)

    Pinto, Alexandre H., E-mail: alehp1@yahoo.com.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod. Washington Luis km 235, CP 676, Sao Carlos 13565-905, SP (Brazil); Souza, Flavio L., E-mail: fleandro.ufabc@gmail.com [Centro de Ciencias Naturais e Humanas, UFABC - Universidade Federal do ABC, Santo Andre 09210-170, SP (Brazil); Longo, Elson, E-mail: elson@iq.unesp.br [Department of Biochemistry, Chemistry Institute of Araraquara, UNESP - Sao Paulo State University, Rua Francisco Degni, CP 355, Araraquara 14801-907, SP (Brazil); Leite, Edson R., E-mail: derl@power.ufscar.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod. Washington Luis km 235, CP 676, Sao Carlos 13565-905, SP (Brazil); Camargo, Emerson R., E-mail: camargo@ufscar.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod. Washington Luis km 235, CP 676, Sao Carlos 13565-905, SP (Brazil)

    2011-10-17

    Highlights: {yields} Highly reactive nanosized powders of Pb(0.8)Pr(0.2)TiO(3) were obtained by the OPM route. {yields} Tetragonal phase was observed by X-ray diffraction and confirmed by Raman spectroscopy. {yields} SEM images showed powders partially sintered with particles of approximately 54 nm. {yields} Dielectric measurements show a normal behavior for the ferroelectric to paraelectric transition. - Abstract: Quasi-spherical nanoparticles of praseodymium-modified lead titanate powder (Pb{sub 0.80}Pr{sub 0.20}TiO{sub 3}) with an average size of 54.8 nm were synthesized successfully by the oxidant-peroxo method (OPM) and were used to prepare highly dense ceramic bodies which were sintered at 1100 and 1150 deg. C for 2 h. A tetragonal phase was identified in the powder and ceramic samples by X-ray powder diffraction and FT-Raman spectroscopy at room temperature. The fractured surface of the ceramic sample showed a high degree of densification with fairly uniform grain sizes. Dielectric constants measured in the range of 30-300 deg. C at different frequencies (120 Hz and at 1, 10 and 100 kHz) indicated that samples with 20 mol% praseodymium showed normal ferroelectric behavior regardless of the sintering temperature.

  14. Structural and dielectric characterization of praseodymium-modified lead titanate ceramics synthesized by the OPM route

    International Nuclear Information System (INIS)

    Pinto, Alexandre H.; Souza, Flavio L.; Longo, Elson; Leite, Edson R.; Camargo, Emerson R.

    2011-01-01

    Highlights: → Highly reactive nanosized powders of Pb(0.8)Pr(0.2)TiO(3) were obtained by the OPM route. → Tetragonal phase was observed by X-ray diffraction and confirmed by Raman spectroscopy. → SEM images showed powders partially sintered with particles of approximately 54 nm. → Dielectric measurements show a normal behavior for the ferroelectric to paraelectric transition. - Abstract: Quasi-spherical nanoparticles of praseodymium-modified lead titanate powder (Pb 0.80 Pr 0.20 TiO 3 ) with an average size of 54.8 nm were synthesized successfully by the oxidant-peroxo method (OPM) and were used to prepare highly dense ceramic bodies which were sintered at 1100 and 1150 deg. C for 2 h. A tetragonal phase was identified in the powder and ceramic samples by X-ray powder diffraction and FT-Raman spectroscopy at room temperature. The fractured surface of the ceramic sample showed a high degree of densification with fairly uniform grain sizes. Dielectric constants measured in the range of 30-300 deg. C at different frequencies (120 Hz and at 1, 10 and 100 kHz) indicated that samples with 20 mol% praseodymium showed normal ferroelectric behavior regardless of the sintering temperature.

  15. Magnetic and electrical transport properties of Pb1-xLaxTi1-xMnxO3 ceramics

    Directory of Open Access Journals (Sweden)

    Jie Xu

    2012-09-01

    Full Text Available Pb1-xLaxTi1-xMnxO3 (PLTM100x, x = 0.20, 0.40, 0.50, 0.60, and 0.80 ceramics have been prepared and investigated. X-ray diffractions show all ceramics are crystallized into perovskite structures with tetragonal symmetry for PLTMO20 and orthorhombic symmetry for the other compositions. X-ray photoelectron spectroscopy results confirm that the Mn cations in PLTMO20 and PLTMO40 have the valence state of +3, whereas in other compositions, the Mn cations have mixed valences states of +3 and +4. With increasing x from 0.20 to 0.80, the materials change from superparamagnetic to coexisting ferromagnetic and antiferromagnetic magnetic behaviour whereas all compositions persist insulating behaviour, as confirmed by the magnetization-magnetic field (M-H, the temperature dependent magnetization (M-T and transport measurements. Especially, the PLTMO80 has a large negative magnetoresistance of −41.5% at 10 K with the applied filed of 2 T. By considering the chemical states of Mn cations, these results are attributed to that the coexistence of metallic ferromagnetic and insulating non-ferromagnetic phases.

  16. Effects of the co-addition of LiSbO3-LiTaO3 on the densification of (Na1/2K1/2)NbO3 lead free ceramics by atmosphere sintering

    International Nuclear Information System (INIS)

    Jiang Na; Fang Bijun; Wu Jian; Du Qingbo

    2011-01-01

    Research highlights: → This manuscript shows a synthesis method that can easily obtain excellent lead-free samples, which is valuable for industrial production. → Pure phase perovskite 0.94(Na 1/2 K 1/2 )NbO 3 -0.03LiSbO 3 -0.03LiTaO 3 (0.94NKN-0.03LS-0.03LT) lead-free piezoelectric ceramics with high relative density, being 94.73%, and excellent integral electrical properties, piezoelectric constant d 33 being 228 pC/N, were prepared by atmosphere sintering method. Which can be attributed to the co-doping of LiSbO 3 -LiTaO 3 . - Abstract: Pure phase perovskite 0.94(Na 1/2 K 1/2 )NbO 3 -0.03LiSbO 3 -0.03LiTaO 3 (0.94NKN-0.03LS-0.03LT) lead-free piezoelectric ceramics were prepared by the conventional solid-state reaction method. Due to the co-addition of LiSbO 3 -LiTaO 3 , the 0.94NKN-0.03LS-0.03LT ceramics prepared by atmosphere sintering at 1040 deg. C exhibit high relative density, being 94.73%, and rather homogenous microstructure. X-ray diffraction (XRD) measurement confirmed that the sintered ceramics exhibit pure tetragonal perovskite structure. The 0.94NKN-0.03LS-0.03LT ceramics exhibit excellent integral electrical properties, in which the value of piezoelectric constant d 33 is 228 pC/N, the electromechanical coupling factors K p and K t are 0.220 and 0.230, respectively, the mechanical quality factor Q m is 32.19, and the remnant polarization P r is 23.06 μC/cm 2 . Such excellent electrical properties are considered as correlating with the high relative density of the synthesized ceramics induced by the co-doping of LiSbO 3 -LiTaO 3 .

  17. Effects of superplastic deformations on thermophysical properties of tetragonal zirconia polycrystals

    International Nuclear Information System (INIS)

    Motohashi, Y.; Wan, C.; Sakuma, T.; Harjo, S.; Shibata, T.; Ishihara, M.; Baba, S.; Hoshiya, T.

    2004-01-01

    Neutron irradiation studies on superplastic zirconia-based ceramics are now in progress as an innovative basic project using the High-temperature Engineering Test Reactor (HTTR) in Japan. The characteristics of the zirconia-based engineering components, made through the formation of superplastic, may be strongly affected by their response to transient or steady-state heat flow. Reliable thermophysical properties such as the coefficients of thermal expansion and thermal conductivity are, therefore, needed to estimate and predict the influence of a high-temperature environment. Accordingly, one of this project's targets is to study the thermophysical properties of superplastic zirconia-based ceramics. The first stage of the research addresses the effects of superplastic deformations on the thermophysical properties of a typical superplastic ceramic, 3 mol% yttria-stabilised tetragonal zirconia polycrystals (3Y-TZP), in its un-irradiated state. First, superplastic tensile deformations were conducted on 3Y-TZP specimens under different conditions in order to obtain specimens with different microstructural characteristics. Afterwards, the following actions were taken: - Specific heat measurements were conducted on the specimens at temperatures ranging from 473 K to 1273 K. - The thermal diffusivity was measured using a laser flash method. The thermal conductivity was then calculated from the measured thermal diffusivity, specific heat and density. - The linear thermal expansion was measured by a push-rod type dilatometer from 300 K to 1473 K. The coefficient of linear thermal expansion (CTE) was estimated from the thermal expansion data. The results obtained from the above measurements are discussed, as is the microstructural evolution caused by the superplastic deformations. It was found that the specific heat was almost independent of microstructural evolution, whereas the thermal diffusivity, thermal conductivity and thermal expansion were quite sensitive to

  18. Multiferroic behavior on nanometric La2/3Ca1/3MnO3 / BaTiO3 bilayers

    Science.gov (United States)

    Prieto, Pedro; Ordoñez, John Edward; Gomez, Maria Elena; Lopera, Wilson

    2014-03-01

    We have deposited bilayers of the FM La2/3Ca1/3MnO3 and FE BaTiO3 as a route to design systems with artificial magnetoelectric coupling on LCMO/BTO/Nb:STO system. We maintain a fixed magnetic layer thickness (tLCMO = 48 nm) and varying the thickness of the ferroelectric layer (tBTO = 20, 50, 100 nm). We analyze the influence of the thickness ratio (tBTO/ tLCMO) in electrical and magnetic properties of manganite. From X-ray diffraction analysis we observed that the samples grew textured. Magnetization and transport measurements indicate a possible multiferroic behavior in the bilayer. We found an increase in the Curie and metal-insulator transition temperature in the bilayer in comparison with those for LCMO (48nm)/STO. Hysteresis loops on bilayers show ferromagnetic behavior. This work has been supported by the ``El Patrimonio Autónomo Fondo Nacional de Financiamiento para CT&I FJC'' Colciencias-CENM Research Projects: No. 1106-48-925531 and CI7917-CC 10510 contract 0002-2013 COLCIENCIAS-UNIVALLE.

  19. Lead-free piezoelectric (K,Na)NbO3-based ceramic with planar-mode coupling coefficient comparable to that of conventional lead zirconate titanate

    Science.gov (United States)

    Ohbayashi, Kazushige; Matsuoka, Takayuki; Kitamura, Kazuaki; Yamada, Hideto; Hishida, Tomoko; Yamazaki, Masato

    2017-06-01

    We developed a (K,Na)NbO3-based lead-free piezoelectric ceramic with a KTiNbO5 system, (K1- x Na x )0.86Ca0.04Li0.02Nb0.85O3-δ-K0.85Ti0.85Nb1.15O5-BaZrO3-Fe2O3-MgO (K1- x N x N-NTK-FM). K1- x N x N-NTK-FM ceramic exhibits a very dense microstructure and a coupling coefficient of k p = 0.59, which is almost comparable to that of conventional lead zirconate titanate (PZT). The (K,Na)NbO3-based ceramic has the Γ15 mode for a wide x range. The nanodomains of orthorhombic (K,Na)NbO3 with the M3 mode coexist within the tetragonal Γ15 mode (K,Na)NbO3 matrix. Successive phase transition cannot occur with increasing x. The maximum k p is observed at approximately the minimum x required to generate the M3 mode phase. Unlike the behavior at the morphotropic phase boundary (MPB) in PZT, the characteristics of K1- x N x N-NTK-FM ceramic in this region changed moderately. This gentle phase transition seems to be a relaxor, although the diffuseness degree is not in line with this hypothesis. Furthermore, piezoelectric properties change from “soft” to “hard” upon the M3 mode phase aggregation.

  20. Growth kinetics of tetragonal and monoclinic ZrO2 crystallites in 3 mol% yttria partially stabilized ZrO2 (3Y-PSZ) precursor powder

    International Nuclear Information System (INIS)

    Kuo, Chih-Wei; Lee, Kuen-Chan; Yen, Feng-Lin; Shen, Yun-Hwei; Lee, Huey-Er; Wen, Shaw-Bing; Wang, Moo-Chin; Stack, Margaret Mary

    2014-01-01

    Highlights: • The crystalline structures were composed of tetragonal and monoclinic ZrO 2 . • Growth kinetics of t-ZrO 2 in the 3Y-PSZ precursor powder is described as: D te 2 =(4.57±0.55)t 0.12±0.02 exp(-((24.79±0.38)×10 3 )/(RT) ). • Growth kinetics of m-ZrO 2 in the 3Y-PSZ precursor powder is described as: D m 2 =(4.40±1.63)t 0.17±0.08 exp(-((66.47±3.97)×10 3 )/(RT) ). - Abstract: The growth kinetics of tetragonal and monoclinic ZrO 2 crystallites in 3 mol% yttria partially stabilized ZrO 2 (3Y-PSZ) precursor powder has been investigated using X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) specific surface area analysis, transmission electron microscopy (TEM) and high resolution TEM (HRTEM). After calcination of the 3Y-PSZ precursor powder between 773 and 1073 K for 2 h, the crystalline structures were composed of tetragonal and monoclinic ZrO 2 as the primary and secondary phases, respectively. When the 3Y-PSZ precursor powder was calcined at 773 K for 2 h, the BET specific surface area was 97.13 m 2 /g, which is equivalent to a particle size of 10.30 nm. The crystallite sizes determined via XRD and BET agreed well, indicating that the powder was virtually non-agglomerated. The growth kinetics of tetragonal and monoclinic ZrO 2 crystallite isothermal growth in the 3Y-PSZ precursor powder are described by: D te 2 =(4.57±0.55)t 0.12±0.02 exp(-((24.79±0.38)×10 3 )/(RT) ) and D m 2 =(4.40±1.63)t 0.17±0.08 exp(-((66.47±3.97)×10 3 )/(RT) ), respectively, for 773K≤T≤1073K. D te and D m denote the crystallite size of tetragonal and monoclinic ZrO 2 at time t and temperature T, respectively

  1. A theoretical investigation of the influence of the surface effect on the ferroelectric property of strained barium titanate film

    Science.gov (United States)

    Fang, Chao; Liu, Wei Hua

    2017-07-01

    The influence of the surface effect on the ferroelectric property of strained barium titanate film has been investigated. In this study, based on time-dependent Ginsburg-Landau-Devonshire thermodynamic theory, the surface effects have been simulated by introducing a surface constant, which leads to the strained BaTiO3 film consisting of inner tetragonal core and gradient lattice strain layer. Further, surface effects produce a depolarization field which has a dominant effect on the ferroelectric properties of the films. The spontaneous polarization, dielectric properties and ferroelectric hysteresis loop of BaTiO3 film are calculated under different boundary conditions. Theoretical and experimental results for strained BaTiO3 film are compared and discussed.

  2. Decorating TiO2 Nanowires with BaTiO3 Nanoparticles: A New Approach Leading to Substantially Enhanced Energy Storage Capability of High-k Polymer Nanocomposites.

    Science.gov (United States)

    Kang, Da; Wang, Guanyao; Huang, Yanhui; Jiang, Pingkai; Huang, Xingyi

    2018-01-31

    The urgent demand of high energy density and high power density devices has triggered significant interest in high dielectric constant (high-k) flexible nanocomposites comprising dielectric polymer and high-k inorganic nanofiller. However, the large electrical mismatch between polymer and nanofiller usually leads to earlier electric failure of the nanocomposites, resulting in an undesirable decrease of electrical energy storage capability. A few studies show that the introduction of moderate-k shell onto a high-k nanofiller surface can decrease the dielectric constant mismatch, and thus, the corresponding nanocomposites can withstand high electric field. Unfortunately, the low apparent dielectric enhancement of the nanocomposites and high electrical conductivity mismatch between matrix and nanofiller still result in low energy density and low efficiency. In this study, it is demonstrated that encapsulating moderate-k nanofiller with high-k but low electrical conductivity shell is effective to significantly enhance the energy storage capability of dielectric polymer nanocomposites. Specifically, using BaTiO 3 nanoparticles encapsulated TiO 2 (BaTiO 3 @TiO 2 ) core-shell nanowires as filler, the corresponding poly(vinylidene fluoride-co-hexafluoropylene) nanocomposites exhibit superior energy storage capability in comparison with the nanocomposites filled by either BaTiO 3 or TiO 2 nanowires. The nanocomposite film with 5 wt % BaTiO 3 @TiO 2 nanowires possesses an ultrahigh discharged energy density of 9.95 J cm -3 at 500 MV m -1 , much higher than that of commercial biaxial-oriented polypropylene (BOPP) (3.56 J cm -3 at 600 MV m -1 ). This new strategy and corresponding results presented here provide new insights into the design of dielectric polymer nanocomposites with high electrical energy storage capability.

  3. Designing magnetic compensated states in tetragonal Mn{sub 3}Ge-based Heusler alloys

    Energy Technology Data Exchange (ETDEWEB)

    You, Yurong; Xu, Guizhou, E-mail: gzxu@njust.edu.cn; Hu, Fang; Gong, Yuanyuan; Liu, Er; Peng, Guo; Xu, Feng, E-mail: xufeng@njust.edu.cn

    2017-05-01

    Magnetic compensated materials attracted much interests due to the observed large exchange bias and large coercivity, and also their potential applications in the antiferromagnetic spintronics with merit of no stray field. In this work, by using ab-initio studies, we designed several Ni (Pd, Pt) doped Mn{sub 3}Ge-based D0{sub 22}-type tetragonal Heusler alloys with fully compensated states. Theoretically, we find the total moment change is asymmetric across the compensation point (at ~x=0.3) in Mn{sub 3-x}Y{sub x}Ge (Y=Ni, Pd, Pt). In addition, an uncommon discontinuous jump is observed across the critical zero-moment point, indicating that some non-trivial properties may emerge at this point. Further electronic analyses of these compensated alloys reveal high spin polarizations at the Fermi level, which is advantageous for spin transfer torque applications. - Highlights: • Several new fully compensated magnetic states are identified in Mn{sub 3}Ge-based tetragonal alloys. • The magnetic moment changes are asymmetric upon Ni, Pd and Pt substitution. • Discontinuous jumps exist across the compensated points. • The three compensated alloys possess large spin polarizations.

  4. Microstructure evolution during pressureless sintering of bulk oxide ceramics

    Directory of Open Access Journals (Sweden)

    Karel Maca

    2009-06-01

    Full Text Available The author’s experience concerning the infl uence of the choice of different pressureless heating schedules on the fi nal microstructure of oxide ceramic materials is summarized in the paper. Alumina, ceria, strontium titanate, as well as tetragonal (3 mol% Y2O3 and cubic (8 mol% Y2O3 zirconia were cold isostatically pressed or injection moulded and pressureless sintered with different heating schedules – namely with Constant-Rate of Heating with different dwell temperatures (CRH, with Rate-Controlled Sintering (RCS and with Two-Step Sintering (TSS. It was examined whether some of these three sintering schedules, with the same fi nal density achieved, can lead to a decrease of the grain size of sintered ceramics. The results showed that only TSS (and only for selected materials brought significant decrease of the grain size.

  5. Properties of lithium disilicate reinforced with ZrO_2 (3mol%Y_2O_3

    International Nuclear Information System (INIS)

    Alves, M.F.R.P.; Cossu, C.M.F.A.; Santos, C.; Simba, B.G.

    2016-01-01

    The new generation of dental ceramics based on lithium disilicate, Li_2Si_2O_5, allows the production of restorative prosthetic with reduced times compared to alumina and / or zirconia (Y-TZP). A great limitation of their use is related low fracture strength of such glass-ceramics, which reduces their use in unit fixed prosthesis. In this work, lithium disilicate reinforced with 10% ZrO_2 (3-mol% Y_2O_3) is characterized by relative density, crystalline phase, hardness, fracture toughness and microstructural aspects. Lithium metasilicate and tetragonal zirconia, prior to heat treatment. After thermal treatment under vacuum at 840 deg C-8min the lithium metasilicate is converted to lithium disilicate as the ZrO_2 phase remains in the tetragonal structure. This maintenance of the tetragonal phase ensures the material a good fracture toughness, reaching average values near 2MPam"1"/"2, while the average hardness of 600HV. Morphological analysis of the samples indicates that ZrO_2 particles are uniformly dispersed in the matrix composed of high aspect ratio lithium disilicate grains, which contributes to the results presented.. A critical analysis of the performance of toughening mechanisms such as cracks deflection, phase transformation of ZrO_2 (T-M), residual stress between the matrix and the reinforcement are presented, discussed and compared with other ceramic materials used in dentistry restorer. (author)

  6. Magnetic behavior of La2/3Ca1/3MnO3 / BaTiO3 bilayers

    Science.gov (United States)

    Ordonez, John E.; Gomez, Maria E.; Lopera, Wilson; Marin, Lorena; Pardo, Jose A.; Morellon, Luis; Algarabel, Pedro; Prieto, Pedro

    2013-03-01

    We have grown ferroelectric BaTiO3(BTO) and ferromagnetic La2/3Ca1/3MnO3 (LCMO) onto (001) SrTiO3 and Nb:SrTiO3 by pulsed laser deposition (PLD) at pure oxygen atmosphere, and a substrate temperature of 820° C, seeking for a multiferroic behavior in this structure. From x-ray diffraction (XRD) we found lattice parameter aBTO=4.068 Å, and aLCMO=3.804 Å, for each individual layer. In the BTO/LCMO bilayer, (002)-Bragg peak for BTO maintain its position whereas (002) LCMO peak shift to lower Bragg angle indicating a strained LCMO film. Magnetization measurements reveal an increase in the Curie temperature from 170 K to 220 K for the bilayer when LCMO (t = 47 nm) is deposited on BTO (t=52 nm) film, while depositing the BTO (50 nm) above LCMO (48 nm) the Curie temperature remains at values close to that obtained for a LCMO single layer (~175 K), deposited under identical growth parameters This work has been supported by Instituto de Nanociencias de Aragón, Zaragoza, Spain, ``El Patrimonio Autónomo Fondo Nacional de Financiamiento para CT&I FJC'' COLCIENCIAS-CENM Contract RC 275-2011 and Research Project COLCIENCIAS-UNIVALLE.

  7. Comparative study of flexural strength test methods on CAD/CAM Y-TZP dental ceramics

    Science.gov (United States)

    Xu, Yongxiang; Han, Jianmin; Lin, Hong; An, Linan

    2015-01-01

    Clinically, fractures are the main cause of computer-aided design and computer-aided manufacturing (CAD/CAM) 3 mol%-yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) all-ceramic dental restorations failure because of repetitive occlusal loading. The goal of this work is to study the effect of test methods and specimen’s size on the flexural strength of five ceramic products. Both bi-axial flexure test (BI) and uni-axial flexure tests (UNI), including three-point flexure test (3PF) and four-point flexure test (4PF), are used in this study. For all five products, the flexural strength is as follows: BI > 3PF > 4PF. Furthermore, specimens with smaller size (3PF-s) have higher values than the bigger ones (3PF). The difference between BI and UNI resulted from the edge flaws in ceramic specimens. The relationship between different UNI (including 3PF-s, 3PF and 4PF) can be explained according to Weibull statistical fracture theory. BI is recommended to evaluate the flexural strength of CAD/CAM Y-TZP dental ceramics. PMID:26816646

  8. Comparative study of flexural strength test methods on CAD/CAM Y-TZP dental ceramics.

    Science.gov (United States)

    Xu, Yongxiang; Han, Jianmin; Lin, Hong; An, Linan

    2015-12-01

    Clinically, fractures are the main cause of computer-aided design and computer-aided manufacturing (CAD/CAM) 3 mol%-yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) all-ceramic dental restorations failure because of repetitive occlusal loading. The goal of this work is to study the effect of test methods and specimen's size on the flexural strength of five ceramic products. Both bi-axial flexure test (BI) and uni-axial flexure tests (UNI), including three-point flexure test (3PF) and four-point flexure test (4PF), are used in this study. For all five products, the flexural strength is as follows: BI > 3PF > 4PF. Furthermore, specimens with smaller size (3PF-s) have higher values than the bigger ones (3PF). The difference between BI and UNI resulted from the edge flaws in ceramic specimens. The relationship between different UNI (including 3PF-s, 3PF and 4PF) can be explained according to Weibull statistical fracture theory. BI is recommended to evaluate the flexural strength of CAD/CAM Y-TZP dental ceramics.

  9. Observation of domain patterns on a ferroelectric ceramic

    International Nuclear Information System (INIS)

    Ibrahim, R.C.; Zavaglia, C.A.C.

    1992-01-01

    In this work ferroelectric domain patterns are observed on a PZT-like ceramic material produced in Brazil. This material has tetragonal unit cell composing a perovskite type structure. The samples, after grinding and polishing, were chemically etched and observed on optical microscope and scanning electron microscope. (author)

  10. Advanced ceramics reinforced with carbon nanotubes for ballistic application

    International Nuclear Information System (INIS)

    Couto, Carlos Alberto de Oliveira; Passador, Fabio Roberto

    2016-01-01

    Full text: The carbon nanotubes have excellent mechanical properties, the elastic modulus is around 1TPa, next to the diamond and the mechanical strength is 10 to 100 times higher than steel, moreover they are self-lubricating, which facilitates the ceramic composites compression process. The insertion of carbon nanotubes tends to improve the fracture toughness of ceramic composites, but is necessary to obtain a good dispersion in the ceramic matrix. The objective of this work is to develop a tough and tenacious ceramics for ballistic application, using structural ceramics of alumina and tetragonal zirconia and evaluate the influence of the addition of carbon nanotubes (multilayer) on the mechanical properties of the composite. The carbon nanotubes were functionalized with carboxylic groups by nitric acid oxidation reaction. To ensure a homogeneous distribution of the carbon nanotubes in the matrix of alumina/zirconia, surfactants were used: sodium dodecyl sulphate + gum arabic in the amount of 50% by mass of carbon nanotubes. Ceramic powders were prepared with pure alumina and alumina + 20% by mass of tetragonal zirconia/yttria, with and without addition of carbon nanotubes at concentrations of 0.1 and 0.5% by mass. The samples were uniaxially and isostatically pressed at 300 MPa and sintered in a conventional oven at 1500 °C for two hours and a heating rate of 5 °C/min, aimed at commercial application. The morphology of ceramic powders were characterized by SEM and XRD. The mechanical properties of the sintered samples were evaluated by flexural bending at three points, Vickers microhardness and fracture toughness by single edge-notched beam (SENB). The use of carbon nanotubes in the ceramic composite caused a decrease in hardness and an increase in fracture toughness, with great potential for ballistic applications. (author)

  11. Advanced ceramics reinforced with carbon nanotubes for ballistic application

    Energy Technology Data Exchange (ETDEWEB)

    Couto, Carlos Alberto de Oliveira; Passador, Fabio Roberto, E-mail: carlos.couto.sjc@gmail.com [Universidade Federal de Sao Paulo (UNIFESP), Sao Jose dos Campos, SP (Brazil)

    2016-07-01

    Full text: The carbon nanotubes have excellent mechanical properties, the elastic modulus is around 1TPa, next to the diamond and the mechanical strength is 10 to 100 times higher than steel, moreover they are self-lubricating, which facilitates the ceramic composites compression process. The insertion of carbon nanotubes tends to improve the fracture toughness of ceramic composites, but is necessary to obtain a good dispersion in the ceramic matrix. The objective of this work is to develop a tough and tenacious ceramics for ballistic application, using structural ceramics of alumina and tetragonal zirconia and evaluate the influence of the addition of carbon nanotubes (multilayer) on the mechanical properties of the composite. The carbon nanotubes were functionalized with carboxylic groups by nitric acid oxidation reaction. To ensure a homogeneous distribution of the carbon nanotubes in the matrix of alumina/zirconia, surfactants were used: sodium dodecyl sulphate + gum arabic in the amount of 50% by mass of carbon nanotubes. Ceramic powders were prepared with pure alumina and alumina + 20% by mass of tetragonal zirconia/yttria, with and without addition of carbon nanotubes at concentrations of 0.1 and 0.5% by mass. The samples were uniaxially and isostatically pressed at 300 MPa and sintered in a conventional oven at 1500 °C for two hours and a heating rate of 5 °C/min, aimed at commercial application. The morphology of ceramic powders were characterized by SEM and XRD. The mechanical properties of the sintered samples were evaluated by flexural bending at three points, Vickers microhardness and fracture toughness by single edge-notched beam (SENB). The use of carbon nanotubes in the ceramic composite caused a decrease in hardness and an increase in fracture toughness, with great potential for ballistic applications. (author)

  12. Performance of zirconia ceramic cantilever fixed dental prostheses: 3-year results from a prospective, randomized, controlled pilot study.

    Science.gov (United States)

    Zenthöfer, Andreas; Ohlmann, Brigitte; Rammelsberg, Peter; Bömicke, Wolfgang

    2015-07-01

    Little is known about the clinical performance of ceramic cantilever fixed dental prostheses on natural teeth. The purpose of this randomized controlled pilot study was to evaluate the clinical performance of ceramic and metal ceramic cantilever fixed dental prostheses (CFDPs) after 3 years of service. Twenty-one participants were randomly allocated to 2 treatment groups. Participants in the ceramic (ZC) group (n=11) each received 1 CFDP made of yttria-stabilized, tetragonal zirconia polycrystal; the others (n=10) were fitted with a metal ceramic (MC) CFDP. All CFDPs were retained by 2 complete crown abutments and replaced 1 tooth. The clinical target variables were survival, incidence of complications, probing pocket depth (PPD), probing attachment level (PAL), plaque index (PI), gingival index (GI), and esthetic performance as rated by the participants. The United States Public Health Service (USPHS) criteria were used to evaluate chipping, retention, color, marginal integrity, and secondary caries. Descriptive statistics and nonparametric analyses were applied to the target variables in the 2 groups. The esthetic performance of the CFDPs was also visualized by using a pyramid comparison. The overall survival of the CFDPs was 100% in both groups. During the 3-year study, 6 clinically relevant complications requiring aftercare were observed among 5 participants (4 in the ZC group and 2 in the MC group). Changes in the PI, GI, PPD, and PAL of the abutment teeth were similar for both groups (P>.05). The participants regarded the esthetic performance of ZC-CFDPs and MC-CFDPs as satisfactory. Within the 3-year observation period, the clinical performance of MC-FDPs and ZC-FDPs was acceptable. More extensive research with larger sample sizes is encouraged, however, to confirm the evaluation of the survival of Y-TZP hand-veneered cantilever FPDs. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  13. Transparent glass–ceramics with (Eu{sup 3+},Yb{sup 3+}):YNbO{sub 4} nanocrystals: Crystallization, structure, optical spectroscopy and cooperative upconversion

    Energy Technology Data Exchange (ETDEWEB)

    Loiko, P.A. [Center for Optical Materials and Technologies (COMT), Belarusian National Technical University, 65/17 Nezavisimosti Ave., Minsk 220013 (Belarus); Dymshits, O.S., E-mail: vodym@goi.ru [NITIOM Vavilov State Optical Institute, 36/1 Babushkin St, Saint-Petersburg 192171 (Russian Federation); Alekseeva, I.P.; Zhilin, A.A.; Tsenter, M.Ya. [NITIOM Vavilov State Optical Institute, 36/1 Babushkin St, Saint-Petersburg 192171 (Russian Federation); Vilejshikova, E.V. [Center for Optical Materials and Technologies (COMT), Belarusian National Technical University, 65/17 Nezavisimosti Ave., Minsk 220013 (Belarus); Bogdanov, K.V. [National Research University of Information Technologies, Mechanics and Optics, Kronverkskiy pr., 49, 197101 Saint-Petersburg (Russian Federation); Mateos, X. [Física i Cristallografia de Materials i Nanomaterials (FiCMA-FiCNA), Universitat Rovira i Virgili (URV), Campus Sescelades, C/Marcellí Domingo, s/n, Tarragona E-43007 (Spain); Yumashev, K.V. [Center for Optical Materials and Technologies (COMT), Belarusian National Technical University, 65/17 Nezavisimosti Ave., Minsk 220013 (Belarus)

    2016-11-15

    In the present work, we report on a comprehensive study of crystallization, structure and optical spectroscopy of transparent glass–ceramics with (Eu{sup 3+},Yb{sup 3+}):YNbO{sub 4} nanocrystals synthesized by secondary heat-treatments of glass of the Li{sub 2}O–Al{sub 2}O{sub 3}–SiO{sub 2} system, for the first time, to the best of our knowledge. Heat treatments result in volume crystallization of RENbO{sub 4} with the sizes of 4–15 nm. Crystals of rare-earth niobates with disordered fluorite structure (T′) appear during heat-treatment at 720–740 °C for 6 h, crystals with tetragonal structure (T) appear at higher temperatures or longer durations of heat-treatment, and in samples heat-treated at 1000 °C, the monoclinic form (M) is detected additionally. Rare-earth niobates act as nucleating agents for bulk crystallization of β-quartz solid solutions, the main crystalline phase of the glass–ceramics, which ensures their good thermo-mechanical properties. Optical spectroscopy confirms entering of both Eu{sup 3+} and Yb{sup 3+} ions into the RENbO{sub 4} nanophase and their specroscopic properties variation according to the T′→T→M phase transformations. Under UV excitation, glass–ceramics heat-treated at 900 °C provide intense red emission with the color coordinates x=0.665, y=0.335 (CIE 1931). In the sample, heat-treated at 1000 °C, a partial reduction of Eu{sup 3+} to Eu{sup 2+} is observed which allows for tuning the color properties of emission. When excited in the near-IR by an InGaAs diode, the initial glass and glass–ceramics show red cooperative upconversion due to the 2Yb{sup 3+}→Eu{sup 3+} energy transfer. The efficiency of the latter is ~10%. The developed materials due to the good emission and thermo-mechanical properties are promising for the development of color-tunable red phosphors.

  14. Review on dielectric properties of rare earth doped barium titanate

    International Nuclear Information System (INIS)

    Ismail, Fatin Adila; Osman, Rozana Aina Maulat; Idris, Mohd Sobri

    2016-01-01

    Rare earth doped Barium Titanate (BaTiO_3) were studied due to high permittivity, excellent electrical properties and have wide usage in various applications. This paper reviewed on the electrical properties of RE doped BaTiO_3 (RE: Lanthanum (La), Erbium (Er), Samarium (Sm), Neodymium (Nd), Cerium (Ce)), processing method, phase transition occurred and solid solution range for complete study. Most of the RE doped BaTiO_3 downshifted the Curie temperature (T_C). Transition temperature also known as Curie temperature, T_C where the ceramics had a transition from ferroelectric to a paraelectric phase. In this review, the dielectric constant of La-doped BaTiO_3, Er-doped BaTiO_3, Sm-doped BaTiO_3, Nd-doped BaTiO_3 and Ce-doped BaTiO_3 had been proved to increase and the transition temperature or also known as T_C also lowered down to room temperature as for all the RE doped BaTiO_3 except for Er-doped BaTiO_3.

  15. Strain and electric field mediated manipulation of magnetism in La_(_1_-_x_)Sr_xMnO_3/BaTiO_3 heterostructures

    International Nuclear Information System (INIS)

    Schmitz, Markus

    2016-01-01

    Heterostructures of ferromagnetic La_1_-_xSr_xMnO_3 (LSMO) and ferroelectric BaTiO_3 (BTO) were produced and investigated for their structural and magnetic properties. The combination of these ferroic properties can lead to an artificial multiferroic. Special emphasis was given to the manipulation of magnetic properties by applying electric fields. A magneto-electric coupling could be observed in the heterostructures under investigation. Epitaxial LSMO thin films were grown on BTO substrates using a state-of-the-art oxide molecular beam epitaxy (OMBE) and a high oxygen sputtering system (HOPSS). Stoichiometric La_1_-_xSr_xMnO_3 films with doping levels of x=0.5 and x=0.3 were produced. The film quality in terms of roughness and crystalline structure was confirmed by X-ray scattering methods. The presence of structural domains in the BaTiO_3 single crystal substrate, whose proportion could be altered due to the application of electric fields, was shown by X-ray diffraction. Tensile strain is induced into the epitaxial La_1_-_xSr_xMnO_3 films in the whole temperature range under investigation. The magnetization of LSMO alteres by the variation of strain induced into the film, generated by the different structural phases of single crystal BaTiO_3 substrates. The magnetization shows sharp steps at the structural phase transition temperatures of BTO. The evaluation of magnetic hysteresis loops reveals a change of the magnetic anisotropy of LSMO for each structural phase of BTO, but also within the orthorhombic phase. Special focus was given to the manipulation of magnetic properties by the application of electric fields. A newly established measurement option was used to determine the magnetic response to an applied electric field as a function of temperature and magnetic field. The electrically induced modification of the magnetization is profound near the structural phase transition temperatures. Electrical hysteresis loops give a detailed view on the influence of the

  16. Piezoelectric ceramic implants: in vivo results.

    Science.gov (United States)

    Park, J B; Kelly, B J; Kenner, G H; von Recum, A F; Grether, M F; Coffeen, W W

    1981-01-01

    The suitability of barium titanate (BaTiO3) ceramic for direct substitution of hard tissues was evaluated using both electrically stimulated (piezoelectric) and inactive (nonpolarized) test implants. Textured cylindrical specimens, half of them made piezoelectric by polarization in a high electric field, were implanted into the cortex of the midshaft region of the femora of dogs for various periods of time. Interfacial healing and bio-compatibility of the implant material were studied using mechanical, microradiographical, and histological techniques. Our results indicate that barium titanate ceramic shows a very high degree of biocompatibility as evidenced by the absence of inflammatory or foreign body reactions at the implant-tissue interface. Furthermore, the material and its surface porosity allowed a high degree of bone ingrowth as evidenced by microradiography and a high degree of interfacial tensile strength. No difference was found between the piezoelectric and the electrically neutral implant-tissue interfaces. Possible reasons for this are discussed. The excellent mechanical properties of barium titanate, its superior biocompatibility, and the ability of bone to form a strong mechanical interfacial bond with it, makes this material a new candidate for further tests for hard tissue replacement.

  17. Synthesis and characterization of multilayered BaTiO3/NiFe2O4 thin films

    Directory of Open Access Journals (Sweden)

    Branimir Bajac

    2013-03-01

    Full Text Available Presented research was focused on the fabrication of multiferroic thin film structures, composed of ferrielectric barium titanate perovskite phase and magnetostrictive nickel ferrite spinel phase. The applicability of different, solution based, deposition techniques (film growth from solution, dip coating and spin coating for thefabrication of multilayered BaTiO3 /NiFe2O4 thin films was investigated. It was shown that only spin coating produces films of desired nanostructure, thickness and smooth and crackfree surfaces.

  18. Structure and phase formation behavior and dielectric and magnetic properties of lead iron tantalate-lead zirconate titanate multiferroic ceramics

    International Nuclear Information System (INIS)

    Wongmaneerung, R.; Tipakontitikul, R.; Jantaratana, P.; Bootchanont, A.; Jutimoosik, J.; Yimnirun, R.; Ananta, S.

    2016-01-01

    Highlights: • The multiferroic ceramics consisted of PFT and PZT. • Crystal structure changed from cubic to mixedcubic and tetragonal with increasing PZT content. • Dielectric showed the samples underwent a typical relaxor ferroelectric behavior. • Magnetic properties showed very interesting behavior with square saturated magnetic hysteresis loops. - Abstract: Multiferroic (1 − x)Pb(Fe_0_._5Ta_0_._5)O_3–xPb(Zr_0_._5_3Ti_0_._4_7)O_3 (or PFT–PZT) ceramics were synthesized by solid-state reaction method. The crystal structure and phase formation of the ceramics were examined by X-ray diffraction (XRD). The local structure surrounding Fe and Ti absorbing atoms was investigated by synchrotron X-ray Absorption Near-Edge Structure (XANES) measurement. Dielectric properties were studied as a function of frequency and temperature using a LCR meter. A vibrating sample magnetometer (VSM) was used to determine the magnetic hysteresis loops. XRD study indicated that the crystal structure of the sample changed from pure cubic to mixed cubic and tetragonal with increasing PZT content. XANES measurements showed that the local structure surrounding Fe and Ti ions was similar. Dielectric study showed that the samples underwent a typical relaxor ferroelectric behavior while the magnetic properties showed very interesting behavior with square saturated magnetic hysteresis loops.

  19. High temperature strengthening of zirconium-toughened ceramics

    International Nuclear Information System (INIS)

    Claussen, N.

    1986-01-01

    Transformation-toughened (i.e. ZrO/sub 2/-toughened) ceramics represent a new class of high performance ceramics with spectacular strength properties at low and intermediate temperatures. However, at temperatures above about 700 0 C, most of these tough oxide-base ceramics can no longer be used as load-bearing engineering parts because of characteristic deficiencies. The aim of the present paper is to provide and discuss microstructural design strategies which may enable ZrO/sub 2/-toughened ceramics to be applied at higher temperatures. From the various strategies suggested, three appear to show good prospects, namely (a) the prevention of glassy intergranular films, (b) the addition of hard high modulus particles and (c) whikser or fibre reinforcement. Experimental approaches are presented from some ZrO/sub 2/-toughened ceramics, elg. tetragonal ZrO/sub 2/ polycrystals and ZrO/sub 2/-toughened cordierite, spinel and mullite

  20. Phase transformation in multiferroic Bi5Ti3FeO15 ceramics by temperature-dependent ellipsometric and Raman spectra: An interband electronic transition evidence

    Science.gov (United States)

    Jiang, P. P.; Duan, Z. H.; Xu, L. P.; Zhang, X. L.; Li, Y. W.; Hu, Z. G.; Chu, J. H.

    2014-02-01

    Thermal evolution and an intermediate phase between ferroelectric orthorhombic and paraelectric tetragonal phase of multiferroic Bi5Ti3FeO15 ceramic have been investigated by temperature-dependent spectroscopic ellipsometry and Raman scattering. Dielectric functions and interband transitions extracted from the standard critical-point model show two dramatic anomalies in the temperature range of 200-873 K. It was found that the anomalous temperature dependence of electronic transition energies and Raman mode frequencies around 800 K can be ascribed to intermediate phase transformation. Moreover, the disappearance of electronic transition around 3 eV at 590 K is associated with the conductive property.

  1. Effect of CASP glass doping on sintering and dielectric properties of SBN ceramics

    International Nuclear Information System (INIS)

    Chen Guohua; Qi Bing

    2009-01-01

    16CaO-29Al 2 O 3 -34SiO 2 -13PbO-4B 2 O 3 -2ZnO-2P 2 O 5 (CASP) glass doped-Sr 0.5 Ba 0.5 Nb 2 O 6 (SBN50) ceramics have been synthesized by solid-state ceramic route. The effects of CASP glass on the firing, microstructure and dielectric characterization of SBN50 ceramics are investigated. The densities of the ceramic samples firstly increase and then slightly decrease with increasing CASP glass content. The appropriate amount of doping glass is 2%. The SBN50 ceramics doped with CASP glass can be sintered at a relatively low temperature, 1200 deg. C. X-ray diffraction analysis shows the single phase (tetragonal tungsten bronze type structure) is preserved for all the samples. The diffuse character of the ceramic system increases and the dielectric constant at phase transition temperature (T c ) markedly decreases as CASP glass content increases. Interestingly, the CASP glass addition drastically alters the microstructure of the sintered ceramics. The isotropic grains in the pure SBN50 ceramics transform to rod like grains after the addition of CASP glass. The grain size of SBN phase is found to obviously increase with increase in CASP glass doping level

  2. Phase transformation and impedance spectroscopic study of Ba substituted Na{sub 0.5}Bi{sub 0.5}TiO{sub 3} ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Kumari, Rekha [Department of Applied Physics, Guru Jambheshwar University of Science & Technology, Hisar, 125001, Haryana (India); Ahlawat, Neetu, E-mail: neetugju@yahoo.co.in [Department of Applied Physics, Guru Jambheshwar University of Science & Technology, Hisar, 125001, Haryana (India); Agarwal, Ashish; Sanghi, Sujata [Department of Applied Physics, Guru Jambheshwar University of Science & Technology, Hisar, 125001, Haryana (India); Sindhu, Monica [Department of Physics, MKJK College, Rohtak, 124001, Haryana (India); Ahlawat, Navneet [Matu Ram Institute of Engineering and Management, Rohtak, 124001, Haryana (India)

    2016-08-15

    (Na{sub 0.5}Bi{sub 0.5}){sub 1−x}Ba{sub x}TiO{sub 3} (x = 0.05, 0.1 and 0.15) ceramics abbreviated as (NBBT1, NBBT2 and NBBT3) are fabricated by conventional ceramic fabrication technique. The analysis of X-ray diffraction pattern of the prepared ceramic performed by Rietveld refinement indicate that crystal structure is rhombohedral for NBBT1, tetragonal for NBBT3 and a phase boundary occurs for NBBT2. Impedance spectroscopy has been employed to study the electrical properties of these ceramics in the frequency range of 10 Hz to 5 MHz and in a temperature range of 303 K–723 K. Frequency and temperature dependent electrical data is analyzed in the framework of conductivity, impedance and electric modulus formalisms. Conductivity spectrum obeys double power law for NBBT1, which is evidenced from two different dispersion regions. While for NBBT2 and NBBT3 only single power law is observed. Relaxation frequency for impedance is found to increase with temperature and obeys Arrhenius relationship with activation energy ≈0.764, 0.527 and 0.471 eV for NBBT1, NBBT2 and NBBT3 respectively. Variation of dielectric constant and tanδ with frequency at different temperatures was analyzed with the help of Maxwell–Wagner and Koop's phenomenogical theory. The presence of peaks in plots showing frequency dependence of tanδ for NBBT2 and NBBT3 indicates relaxor behavior of these compositions. - Highlights: • (Na{sub 0.5}Bi{sub 0.5}){sub 1−x}Ba{sub x}TiO{sub 3} (x = 0.05, 0.1, 0.15) ceramics have been synthesized. • There is change in crystal structure with Ba doping. • NBBT2 and NBBT3 show relaxor behavior.

  3. Feasibility of Using Multilayer Platelets as Toughening Agents

    Directory of Open Access Journals (Sweden)

    Yuan-Liang Chin

    2009-12-01

    Full Text Available It is known that the toughness of brittle ceramics can be improved significantly with the addition of hard platelets. In the present study, platelet-shape multilayer ceramic laminates are utilized as a toughening agent for alumina ceramics. They are prepared by laminating the BaTiO3-based ceramic tapes. Although the elastic modulus of the BaTiO3-based platelets is lower than that of the alumina matrix, and the platelets are also reactive to alumina at elevated temperatures, the weak platelets are found to exhibit the ability to deflect major matrix cracks by forming a large number of microcrack branches within the platelets, thus achieving the desired toughening effect.

  4. Shell model for BaTiO3-Bi(Zn1/2Ti1/2)O3 perovskite solid solutions

    Science.gov (United States)

    Vielma, J.; Jackson, D.; Roundy, D.; Schneider, G.

    2010-03-01

    Even though the composition of BaTiO3-Bi(Zn1/2Ti1/2)O3 perovskite solid solutions is similar to other ferroelectric compounds, the dielectric response is unusual. Results of permittivity measurements as a function of temperature show a diffuse phase transition indicative of a weakly coupled relaxor behavior.footnotetextC. C. Huang and D. P. Cann, J. Appl. Phys. 104, 024117 (2008) To investigate the weakly coupled relaxor behavior in these materials at intermediate length scales we are developing a newly calibrated shell model based on first-principles supercell calculations of both the solid solution and its compositional endpoints. Initial results for its phase diagram will presented.

  5. A wear-resistant zirconia ceramic for low friction application

    International Nuclear Information System (INIS)

    Winnubst, A.J.A.; Ran, S.; Wiratha, K.W.; Blank, D.H.A.; Pasaribu, H.R.; Sloetjes, J.W.; Schipper, D.J.

    2004-01-01

    A high wear-resistant ceramic/ceramic couple is described associated with low friction. By adding a small amount CuO to yttria-doped tetragonal zirconia (Y-TZP) the (dry) coefficient of friction against alumina is only 0.2 during a sliding distance of 3-5 km after which the coefficient drastically increases and a transition from mild to sever wear occurs. Pure Y-TZP exhibits a coefficient of friction of 0.7 under the same experimental conditions but wear remains mild during the test (upto 10 km of sliding distance). These small amounts of CuO also strongly influence the densification behaviour. Sintering of this system occurs in several steps where among other things dissolution of CuO in the Y-TZP matrix as well as liquid phase sintering takes place. Non-uniform shrinkage of the CuO-doped system resulting in relative large microcracks in the ceramic can explain its sudden drastic increase in coefficient of friction and wear rate after 3-5 km of operation. (orig.)

  6. Electric controlling of surface metal-insulator transition in the doped BaTiO3 film

    Directory of Open Access Journals (Sweden)

    Wei Xun

    2017-07-01

    Full Text Available Based on first-principles calculations, the BaTiO3(BTO film with local La-doping is studied. For a selected concentration and position of doping, the surface metal-insulator transition occurs under the applied electric field, and the domain appears near the surface for both bipolar states. Furthermore, for the insulated surface state, i.e., the downward polarization state in the doped film, the gradient bandgap structure is achieved, which favors the absorption of solar energy. Our investigation can provide an alternative avenue in modification of surface property and surface screening effect in polar materials.

  7. Impedance spectroscopy studies on lead free Ba1-xMgx(Ti0.9Zr0.1)O3 ceramics

    Science.gov (United States)

    Ben Moumen, S.; Neqali, A.; Asbani, B.; Mezzane, D.; Amjoud, M.; Choukri, E.; Gagou, Y.; El Marssi, M.; Luk'yanchuk, Igor A.

    2018-06-01

    Ba1-xMgx(Ti0.9Zr0.1)O3 (x = 0.01 and 0.02) ceramics were prepared using the conventional solid state reaction. Rietveld refinement performed on X-ray diffraction patterns indicates that the samples are tetragonal crystal structure with P4mm space group. By increasing Mg content from 1 to 2% the unit cell volume decreased. Likewise, the grains size is greatly reduced from 10 μm to 4 μm. The temperature dependence of dielectric constants at different frequencies exhibited typical relaxor ferroelectric characteristic, with sensitive dependence in frequency and temperature for ac conductivity. The obtained activation energy values were correlated to the proposed conduction mechanisms.

  8. Tetragonal-cubic phase boundary in nanocrystalline ZrO2-Y2O3 solid solutions synthesized by gel-combustion

    International Nuclear Information System (INIS)

    Fabregas, Ismael O.; Craievich, Aldo F.; Fantini, Marcia C.A.; Millen, Ricardo P.; Temperini, Marcia L.A.; Lamas, Diego G.

    2011-01-01

    Research highlights: → Gel-combustion synthesis yields compositionally homogeneous, single-phased ZrO 2 -Y 2 O 3 nanopowders, that exhibit the presence at room temperature of three different phases depending on Y 2 O 3 content, namely two tetragonal forms (t' and t'') and the cubic phase. → Phase identification can be achieved by synchrotron XPD (SXPD) and Raman spectroscopy since the tetragonal forms and the cubic phase can be distinguished by these techniques. → The crystallographic features of ZrO 2 -Y 2 O 3 nanopowders were determined by SXPD. They are similar to those reported by Yashima and coworkers for compositionally homogeneous materials containing larger (micro)crystals. However, the lattice parameters are slightly different and the axial ratios c/a of our t' samples are smaller than those reported by these authors. → Compositional t'/t'' and t''/cubic phase boundaries are located at (9 ± 1) and (10.5 ± 0.5) mol% Y 2 O 3 , respectively. → For the whole series of nanocrystalline ZrO 2 -Y 2 O 3 solid solutions studied in the present work, no evidences of the presence of a mixture of phases - as reported by Yashima and coworkers for microcrystalline solid solutions - were detected. - Abstract: By means of synchrotron X-ray powder diffraction (SXPD) and Raman spectroscopy, we have detected, in a series of nanocrystalline and compositionally homogeneous ZrO 2 -Y 2 O 3 solid solutions, the presence at room temperature of three different phases depending on Y 2 O 3 content, namely two tetragonal forms and the cubic phase. The studied materials, with average crystallite sizes within the range 7-10 nm, were synthesized by a nitrate-citrate gel-combustion process. The crystal structure of these phases was also investigated by SXPD. The results presented here indicate that the studied nanocrystalline ZrO 2 -Y 2 O 3 solid solutions exhibit the same phases reported in the literature for compositionally homogeneous materials containing larger (micro

  9. /sup 87/Rb NMR study at the cubic to tetragonal phase transition in RbCaF/sub 3/

    Energy Technology Data Exchange (ETDEWEB)

    Bulou, A [Angers Univ., 72 - Le Mans (France). Centre Universitaire; Theveneau, H; Trokiner, A; Papon, P [Ecole Superieure de Physique et Chimie Industrielles, 75 - Paris (France)

    1979-07-01

    The /sup 87/Rb nuclear magnetic resonance spectrum, in perovskite single crystal of RbCaF/sub 3/, is studied above and below the cubic-to-tetragonal phase transition occurring at 198 K. In the high-temperature cubic phase, the temperature dependence of the resonance line amplitude deviates from the Curie law and this can be attributed to the existence of tetragonal domains. In the low temperature tetragonal phase, a second-order quadrupole shift of the central line is observed, from which the CaF/sub 6/ tilt angle (order parameter) is derived. The order parameter temperature dependence is described by a power law with a cross over from exponent 0.5 to exponent 0.32 at 150 K. The tilt angle PHI is compared to the values obtained from X-ray and neutron powder diffraction data.

  10. Properties of lithium disilicate reinforced with ZrO{sub 2} (3mol%Y{sub 2}O{sub 3}; Propriedades de dissilicato de litio reforcado com ZrO{sub 2} (3mol%Y{sub 2}O{sub 3})

    Energy Technology Data Exchange (ETDEWEB)

    Alves, M.F.R.P.; Cossu, C.M.F.A.; Santos, C., E-mail: manuelfellipealves@gmail.com [Universidade do Estado do Rio de Janeiro (UERJ), Resende, RJ (Brazil). Faculdade de Tecnologia; Silva, C.L.M. [Centro Universitario de Volta Redonda (UniFOA), Volta Redonda, RJ (Brazil); Simba, B.G. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Guaratingueta, SP (Brazil). Faculdade de Engenharia; Fernandes, M.H.F. [Universidade de Aveiro (Portugal)

    2016-07-01

    The new generation of dental ceramics based on lithium disilicate, Li{sub 2}Si{sub 2}O{sub 5}, allows the production of restorative prosthetic with reduced times compared to alumina and / or zirconia (Y-TZP). A great limitation of their use is related low fracture strength of such glass-ceramics, which reduces their use in unit fixed prosthesis. In this work, lithium disilicate reinforced with 10% ZrO{sub 2} (3-mol% Y{sub 2}O{sub 3}) is characterized by relative density, crystalline phase, hardness, fracture toughness and microstructural aspects. Lithium metasilicate and tetragonal zirconia, prior to heat treatment. After thermal treatment under vacuum at 840 deg C-8min the lithium metasilicate is converted to lithium disilicate as the ZrO{sub 2} phase remains in the tetragonal structure. This maintenance of the tetragonal phase ensures the material a good fracture toughness, reaching average values near 2MPam{sup 1/2}, while the average hardness of 600HV. Morphological analysis of the samples indicates that ZrO{sub 2} particles are uniformly dispersed in the matrix composed of high aspect ratio lithium disilicate grains, which contributes to the results presented.. A critical analysis of the performance of toughening mechanisms such as cracks deflection, phase transformation of ZrO{sub 2} (T-M), residual stress between the matrix and the reinforcement are presented, discussed and compared with other ceramic materials used in dentistry restorer. (author)

  11. Chemical treatment and biomimetic coating evaluating in zirconia-alumina ceramics

    International Nuclear Information System (INIS)

    Aguiar, Amanda Abati

    2007-01-01

    Ceramic materials, as alumina and zirconia have been explored along the years as biomaterials application. The bio inert nature has been stimulating the development of new alternatives, as chemical treatments to improve the biological application of these ceramics. The biomimetic process of bio inert ceramics for coating apatite is based on soaking the implant in a simulated body fluid, SBF, with ion concentrations nearly equal to those of human blood plasma. The bioactivity of the material is related with the formation of a layer constituted of hydroxyapatite low crystalline, similar to the biological apatite. The biocompatibility associated to the structural properties of the alumina and zirconia has been stimulating the clinical use of these materials, mainly in areas of larger mechanical requests, places not recommended for bioactive hydroxyapatite, for instance. In this work samples of alumina, zirconia doped with Yttria (3% mol) and composites of alumina and zirconia doped with Yttria (3% mol) were prepared by co-precipitation method, calcinate, sintered, chemically treated with solutions of acid phosphoric and sodium hydroxide and them immersed in 1.0 M and 1.5 M SBF. The calcinate powders were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), gas adsorption (BET) and laser diffraction. The XRD results indicate that the samples are low crystalline. It was observed for BET that the samples present high specific surface area. The results of laser diffraction and SEM showed that the powders are agglomerates. The sintered samples were analyzed by XRD, SEM and X-ray fluorescence (XRF). The phases quantified by Rietveld method were: cubic, tetragonal and monoclinic of the zirconia, besides the phase alpha of the alumina. The chemical treatment with phosphoric acid didn't present a tendency of larger apatite formation in relation to the samples no chemically treated. The treatment with sodium hydroxide provoked accentuated transformation of

  12. Ultrasonic Transducer Fabricated Using Lead-Free BFO-BTO+Mn Piezoelectric 1-3 Composite

    Directory of Open Access Journals (Sweden)

    Yan Chen

    2015-05-01

    Full Text Available Mn-doped 0.7BiFeO3-0.3BaTiO3 (BFO-0.3BTO+Mn 1% mol lead-free piezoelectric ceramic were fabricated by traditional solid state reaction. The phase structure, microstructure, and ferroelectric properties were investigated. Additionally, lead-free 1–3 composites with 60% volume fraction of BFO-BTO+Mn ceramic were fabricated for ultrasonic transducer applications by a conventional dice-and-fill method. The BFO-BTO+Mn 1-3 composite has a higher electromechanical coupling coefficient (kt = 46.4% and lower acoustic impedance (Za ~ 18 MRayls compared with that of the ceramic. Based on this, lead-free piezoelectric ceramic composite, single element ultrasonic transducer with a center frequency of 2.54 MHz has been fabricated and characterized. The single element transducer exhibits good performance with a broad bandwidth of 53%. The insertion loss of the transducer was about 33.5 dB.

  13. Phase transformation in multiferroic Bi5Ti3FeO15 ceramics by temperature-dependent ellipsometric and Raman spectra: An interband electronic transition evidence

    International Nuclear Information System (INIS)

    Jiang, P. P.; Duan, Z. H.; Xu, L. P.; Zhang, X. L.; Li, Y. W.; Hu, Z. G.; Chu, J. H.

    2014-01-01

    Thermal evolution and an intermediate phase between ferroelectric orthorhombic and paraelectric tetragonal phase of multiferroic Bi 5 Ti 3 FeO 15 ceramic have been investigated by temperature-dependent spectroscopic ellipsometry and Raman scattering. Dielectric functions and interband transitions extracted from the standard critical-point model show two dramatic anomalies in the temperature range of 200–873 K. It was found that the anomalous temperature dependence of electronic transition energies and Raman mode frequencies around 800 K can be ascribed to intermediate phase transformation. Moreover, the disappearance of electronic transition around 3 eV at 590 K is associated with the conductive property

  14. Zirconium oxide based ceramic solid electrolytes for oxygen detection

    International Nuclear Information System (INIS)

    Caproni, Erica

    2007-01-01

    Taking advantage of the high thermal shock resistance of zirconia-magnesia ceramics and the high oxide ion conductivity of zirconia-yttria ceramics, composites of these ceramics were prepared by mixing, pressing and sintering different relative concentrations of ZrO 2 : 8.6 mol% MgO and ZrO 2 : 3 mol% Y 2 O 3 solid electrolytes. Microstructural analysis of the composites was carried out by X-ray diffraction and scanning electron microscopy analyses. The thermal behavior was studied by dilatometric analysis. The electrical behavior was evaluated by the impedance spectroscopy technique. An experimental setup was designed for measurement the electrical signal generated as a function of the amount of oxygen at high temperatures. The main results show that these composites are partially stabilized (monoclinic, cubic and tetragonal) and the thermal behavior is similar to that of ZrO 2 : 8.6 mol% MgO materials used in disposable high temperature oxygen sensors. Moreover, the results of analysis of impedance spectroscopy show that the electrical conductivity of zirconia:magnesia is improved with zirconia-yttria addition and that the electrical signal depends on the amount of oxygen at 1000 deg C, showing that the ceramic composites can be used in oxygen sensors. (author)

  15. Emergence of the sub-THz central peak at phase transitions in artificial BaTiO3/(Ba,Sr)TiO3 superlattices

    International Nuclear Information System (INIS)

    Tikhonov, Yu.A.; Razumnaya, A.G.; Torgashev, V.I.; Zakharchenko, I.N.; Yuzyuk, Yu.I.; El Marssi, M.; Ortega, N.; Kumar, A.; Katiyar, R.S.

    2015-01-01

    A prominent central peak in the sub-THz frequency range was observed in the Raman spectra of BaTiO 3 /(Ba,Sr)TiO 3 (BT/BST) superlattice grown on (001)MgO substrate. Both soft and central mode show an anomaly around 200 K and 280 K, which can be correlated with orthorhombic to monoclinic phase transition of BST and BT, respectively. The observed temperature dependence of the central mode enabled us to explain rather broad temperature dependence of the dielectric permittivity previously observed in BT/BST superlattices. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  16. Mechanical confinement for improved energy storage density in BNT-BT-KNN lead-free ceramic capacitors

    Directory of Open Access Journals (Sweden)

    Aditya Chauhan

    2014-08-01

    Full Text Available With the advent of modern power electronics, embedded circuits and non-conventional energy harvesting, the need for high performance capacitors is bound to become indispensible. The current state-of-art employs ferroelectric ceramics and linear dielectrics for solid state capacitance. However, lead-free ferroelectric ceramics propose to offer significant improvement in the field of electrical energy storage owing to their high discharge efficiency and energy storage density. In this regards, the authors have investigated the effects of compressive stress as a means of improving the energy storage density of lead-free ferroelectric ceramics. The energy storage density of 0.91(Bi0.5Na0.5TiO3-0.07BaTiO3-0.02(K0.5Na0.5NbO3 ferroelectric bulk ceramic was analyzed as a function of varying levels of compressive stress and operational temperature .It was observed that a peak energy density of 387 mJ.cm-3 was obtained at 100 MPa applied stress (25oC. While a maximum energy density of 568 mJ.cm-3 was obtained for the same stress at 80oC. These values are indicative of a significant, 25% and 84%, improvement in the value of stored energy compared to an unloaded material. Additionally, material's discharge efficiency has also been discussed as a function of operational parameters. The observed phenomenon has been explained on the basis of field induced structural transition and competitive domain switching theory.

  17. Dielectric Performance of High Permitivity Nanocomposites: Impact of Polystyrene Grafting on BaTiO3 and TiO2

    Science.gov (United States)

    2016-09-22

    prepared using high-shear mixing (Ultra-Turrax T18, IKA). All BaTiO3 nanocomposites were solution cast from DMF onto aluminum-coated glass substrates...coated from chlorobenzene onto aluminum-coated glass substrates. Figure 3 a Real dielectric permittivity ε′ measured at 1 kHz for PS@BaTiO3 HNPs... SiO2 nanocomposites, where 15% v/v PS  +  SiO2 blends exhibited degraded energy storage efficiencies when driven above 100 V/μm, while 18% v/v PS@ SiO2

  18. Alumina reinforced tetragonal zirconia (TZP) composites. Final technical report, July 1, 1993--December 31, 1996

    International Nuclear Information System (INIS)

    Shetty, D.K.

    1997-01-01

    This final technical report summarizes the significant research results obtained during the period July 1, 1993 through December 31, 1996 in the DOE-supported research project entitled, open-quotes Alumina Reinforced Tetragonal Zirconia (TZP) Compositesclose quotes. The objective of the research was to develop high-strength and high-toughness ceramic composites by combining mechanisms of platelet, whisker or fiber reinforcement with transformation toughening. The approach used included reinforcement of Celia- or yttria-partially-stabilized zirconia (Ce-TZP or Y-TZP) with particulates, platelets, or continuous filaments of alumina

  19. Magnetostriction in composites of LiFe5O8-BaTiO3

    International Nuclear Information System (INIS)

    Sarah, P.; Suryanarayana, S.V.

    2003-01-01

    Polycrystalline lithium ferrite, LiFe 5 O 8 was prepared by adopting two preparation techniques, the solid-state double sintering method and the sol-gel method. This ferrite powder was thoroughly mixed with barium titanate, BaTiO 3 for preparation of di-phasic composites of lithium ferrite and barium titanate. X-ray diffraction study of these composites revealed the presence of both the phases. Magnetostriction of these composites was measured in varying magnetic fields. The value of magnetostriction for the composites prepared by the sol-gel method was found to be higher than the values obtained in case of composites prepared by the solid-state method. Magnetostriction was found to decrease with increasing content of barium titanate. The saturation field was found to increase with the introduction of barium titanate

  20. Growth kinetics of tetragonal and monoclinic ZrO{sub 2} crystallites in 3 mol% yttria partially stabilized ZrO{sub 2} (3Y-PSZ) precursor powder

    Energy Technology Data Exchange (ETDEWEB)

    Kuo, Chih-Wei [Department of Resources Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Lee, Kuen-Chan [Department of Fragrance and Cosmetic Science, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Yen, Feng-Lin, E-mail: flyen@kmu.edu.tw [Department of Fragrance and Cosmetic Science, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Shen, Yun-Hwei [Department of Resources Engineering, National Cheng Kung University, 1 Ta-Hsueh Road, Tainan 70101, Taiwan (China); Lee, Huey-Er [Department of Dentistry, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Department of Dentistry, Kaohsiung Medical University, Chung Ho Memorial Hospital, 100 Tzyou 1st Road, Kaohsiung 807, Taiwan (China); Wen, Shaw-Bing [General Education Center, Meiho Institute of Technology, 23 Pingguang Road, Neipu, Pingtung 91202, Taiwan (China); Wang, Moo-Chin, E-mail: mcwang@kmu.edu.tw [Department of Fragrance and Cosmetic Science, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Stack, Margaret Mary [Department of Mechanical and Aerospace Engineering, University of Strathclyde, 75 Montrose Street, Glasgow (United Kingdom)

    2014-04-01

    Highlights: • The crystalline structures were composed of tetragonal and monoclinic ZrO{sub 2}. • Growth kinetics of t-ZrO{sub 2} in the 3Y-PSZ precursor powder is described as: D{sub te}{sup 2}=(4.57±0.55)t{sup 0.12±0.02}exp(-((24.79±0.38)×10{sup 3})/(RT) ). • Growth kinetics of m-ZrO{sub 2} in the 3Y-PSZ precursor powder is described as: D{sub m}{sup 2}=(4.40±1.63)t{sup 0.17±0.08}exp(-((66.47±3.97)×10{sup 3})/(RT) ). - Abstract: The growth kinetics of tetragonal and monoclinic ZrO{sub 2} crystallites in 3 mol% yttria partially stabilized ZrO{sub 2} (3Y-PSZ) precursor powder has been investigated using X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) specific surface area analysis, transmission electron microscopy (TEM) and high resolution TEM (HRTEM). After calcination of the 3Y-PSZ precursor powder between 773 and 1073 K for 2 h, the crystalline structures were composed of tetragonal and monoclinic ZrO{sub 2} as the primary and secondary phases, respectively. When the 3Y-PSZ precursor powder was calcined at 773 K for 2 h, the BET specific surface area was 97.13 m{sup 2}/g, which is equivalent to a particle size of 10.30 nm. The crystallite sizes determined via XRD and BET agreed well, indicating that the powder was virtually non-agglomerated. The growth kinetics of tetragonal and monoclinic ZrO{sub 2} crystallite isothermal growth in the 3Y-PSZ precursor powder are described by: D{sub te}{sup 2}=(4.57±0.55)t{sup 0.12±0.02}exp(-((24.79±0.38)×10{sup 3})/(RT) ) and D{sub m}{sup 2}=(4.40±1.63)t{sup 0.17±0.08}exp(-((66.47±3.97)×10{sup 3})/(RT) ), respectively, for 773K≤T≤1073K. D{sub te} and D{sub m} denote the crystallite size of tetragonal and monoclinic ZrO{sub 2} at time t and temperature T, respectively.

  1. Etude de capacités en couches minces à base d'oxydes métalliques à très forte constante diélectrique, BaTiO3, SrTiO3 et SrTiO3/BaTiO3 déposées par pulvérisation par faisceau d'ions

    OpenAIRE

    Guillan , Julie

    2005-01-01

    In a view of miniaturization in microelectronics and more particularly in the sector of mobile phone, perovskites materials with very high permittivity are interesting candidates to replace dielectrics currently used in the development of Metal/Insulator/Metal (MIM) capacitor. This work is devoted to the development and the characterization of thin layers of strontium titanate (SrTiO3) and barium titanate (BaTiO3) deposited by Ion Beam Sputtering (IBS) in capacitive structure Pt/high-k/Pt.An ...

  2. BaTiO3-based nanolayers and nanotubes: first-principles calculations.

    Science.gov (United States)

    Evarestov, Robert A; Bandura, Andrei V; Kuruch, Dmitrii D

    2013-01-30

    The first-principles calculations using hybrid exchange-correlation functional and localized atomic basis set are performed for BaTiO(3) (BTO) nanolayers and nanotubes (NTs) with the structure optimization. Both the cubic and the ferroelectric BTO phases are used for the nanolayers and NTs modeling. It follows from the calculations that nanolayers of the different ferroelectric BTO phases have the practically identical surface energies and are more stable than nanolayers of the cubic phase. Thin nanosheets composed of three or more dense layers of (0 1 0) and (0 1 1[overline]) faces preserve the ferroelectric displacements inherent to the initial bulk phase. The structure and stability of BTO single-wall NTs depends on the original bulk crystal phase and a wall thickness. The majority of the considered NTs with the low formation and strain energies has the mirror plane perpendicular to the tube axis and therefore cannot exhibit ferroelectricity. The NTs folded from (0 1 1[overline]) layers may show antiferroelectric arrangement of Ti-O bonds. Comparison of stability of the BTO-based and SrTiO(3)-based NTs shows that the former are more stable than the latter. Copyright © 2012 Wiley Periodicals, Inc.

  3. Enhanced output performance of a lead-free nanocomposite generator using BaTiO3 nanoparticles and nanowires filler

    Science.gov (United States)

    Baek, Changyeon; Yun, Jong Hyuk; Wang, Hee Seung; Wang, Ji Eun; Park, Hyeonbin; Park, Kwi-Il; Kim, Do Kyung

    2018-01-01

    Flexible nanocomposite generators based on piezoelectric nanoparticles (NPs)-polymeric matrix have been attracted attention as the energy harvesting device converted the electricity from the mechanical deformations. To enhance the piezo-potential difference introduced inside the piezoelectric nanocomposite, one-dimensional nanostructures such as CNTs, copper nanorods, and Ag nanowires (NWs) should be used inevitably as a dispersing agent for achieving well-distributed piezoelectric nanoparticles in an elastomer. These non-piezoelectric additives showed versatile roles; however, their toxicity to living organism has been an obstacle to realize the bio-eco-friendly flexible energy harvesters. Replacing them with piezoelectric NWs with non-toxic can be a challengeable approach to achieve not only the original purposes of additives but also the improvement of output performance. Here, we synthesized well-crystallized BaTiO3 spherical and acicular NPs via a simple hydrothermal reaction and the two-step hydrothermal reactions, respectively and produced piezoelectric nanocomposite made of piezoelectric BaTiO3 NPs and NWs without toxic dispersion enhancers. Output performance of the fabricated flexible energy harvesters with varying the composition of NPs and NWs were investigated by the well-optimized measurement system during the periodical bending and unbending. A nanocomposite-based energy harvester with 4:1 wt ratio generated the maximum open-circuit voltage and short-circuit current of 60 V and 1.1 μA, respectively.

  4. BaTiO3 thick fi lms obtained by tape casting from powders prepared by the oxalate route

    Directory of Open Access Journals (Sweden)

    Adelina Ianculescu

    2009-06-01

    Full Text Available BaTiO3 powders were prepared by co-precipitation via oxalate route. The size, morphology and particle size distribution of the oxalate powders have been optimized by the control of different synthesis parameters during the precipitation reaction (nature of salts, concentration of different solutions, aging time. The single phase BaTiO3 oxide particles were obtained after a thermal decomposition of the as-synthesized powders at 850°C for 4 hours under air atmosphere. Oxide powders with a suitable specifi c surface area were selected in order to obtain thick fi lms by the tape casting technique. The microstructure and dielectric properties of the thick films varied obviously depending on the deposition-calcination-sintering cycle used. A double depositioncalcination cycle followed by sintering, as well as a two step deposition-calcination-sintering procedure was used in order to improve the compactness and therefore, the dielectric behaviour. A higher dielectric constant value (~ 750 and lower dielectric losses (~ 2 % were achieved at room temperature and at 1 kHz frequency for the dense, double-deposited fi lm obtained after two deposition-calcination-sintering cycles. For this film, a superior value of the dielectric constant (~ 1100, almost frequency independent in the frequency range of 100 Hz – 10 kHz was gained also at the ferroelectric-paraelectric phase transition temperature of 130°C.

  5. Ferroelectric properties of BaTiO3/PbZr0.2Ti.08O3 bilayer thin film

    Science.gov (United States)

    Salev, Pavel; Yang, Chun; Grigoriev, Alexei

    2014-03-01

    The thin film ferroelectric BaTiO3/PbZr0.2Ti0.8O3 bilayer was epitaxially grown on SrRuO3/SrTiO3 substrate by RF sputtering. Electrical measurements of polarization switching revealed two different switching regimes - a small ferroelectric hysteresis loop at low applied voltage and a larger loop at a high voltage. The measured dielectric permittivity corresponds to weak electrostatic coupling between two layers according to Landau-Ginsburg-Devonshire theory. This weak coupling may allow for independent polarization states to exist in individual layers. This can lead to stable head-to-head and tail-to-tail polarization domain configurations, which would explain the two switching regimes observed in electrical measurements. The compensation of polarization gradient across the interface can be explained by the enhancement of interface charge carrier density due to strong bending of electron energy bands. This work was supported by NSF award DMR-1057159.

  6. Is there an ordered tetragonal phase in the Ti3Al-Nb system?

    International Nuclear Information System (INIS)

    Banerjee, D.

    1994-01-01

    In a recent series of papers, describing aging transformations in plasma sprayed Ti-24Al-11Nb, Hsiung and co-workers proposed a new ordered tetragonal structure as the first metastable phase to form in a series of transformations from quenched-in B2 to the equilibrium phase. They describe this new phase as a ''DO 3 like tetragonal structure'' with a composition Ti 5 Al 2 Nb, and lattice parameters, a = 0.65 nm and c/a ≅ 1.02. Their unit cell is constituted by 8 bcc unit cells, and the atomic coordinates of their structure are given in Table 1 on this basis. The symmetry of this structure is P4/mm. Though it is not the smallest possible unit cell for the structure, comparison with other bcc binary derivative structures is easily possible on this basis. The atomic coordinates for the latter, for a ternary composition Ti 2 AlNb, are also given. They note that the site occupation for the Hsiung et al. structure is quite distinct from that for a ternary DO 3 phase or any of the other possible bcc derivative structures (neglecting 2 possibilities with 128 or 432 atoms per unit cell(8) and interstitial ordering)

  7. Lattice vibrations and cubic to tetragonal phase transition in ZrO2

    International Nuclear Information System (INIS)

    Negita, K.

    1989-01-01

    On the basis of analyses of phonon modes in ZrO 2 , it is suggested that condensation of a phonon X 2 - at the cubic Brillouin zone boundary X point, (0, 0, 2 π/a), is associated with the cubic to tetragonal phase transition in ZrO 2 . Free energy consideration shows that spontaneous volume and shear strains, e Alg = (e 1 +e 2 +e 3 ) and e Eg = (2e 3 - e 1 - e 2 )/ Λ3, are induced in the tetragonal phase as a result of indirect couplings of the X 2 - mode to homogeneous elastic strains; the tetragonal phase is improper ferroelastic

  8. On the nature of phase transitions in the tetragonal tungsten bronze GdK2Nb5O15 ceramics

    International Nuclear Information System (INIS)

    Gagou, Y.; Lukyanchuk, I.; El Marssi, M.; Amira, Y.; Mezzane, D.; Courty, M.; Masquelier, C.; Yuzyuk, Yu. I.

    2014-01-01

    Phase transitions in gadolinium potassium niobate GdK 2 Nb 5 O 15 (GKN) ceramics have been investigated by x-ray diffraction, dielectric susceptibility, differential scanning calorimetry, and Raman scattering. The results of our complementary studies show that GKN exhibits two phase transitions at T c1  = 238 °C and T c2  = 375 °C attributed to the ferroelectric-antiferroelectric-paraelectric (FE-AFE-PE) phase transitions. According to the x-ray diffraction analysis, the FE and PE phases were refined in the polar P4bm and centrosymmetric P4/mbm space groups. For the intermediate phase, the structure is refined in the space group P4nc with doubling of the c unit cell parameter, which is compatible with an AFE phase. This result was confirmed by Raman spectroscopy since new low-frequency lines are activated in the AFE phase due to the Brillouin zone-folding effect, typical for the modulated phases. The presence of the AFE phase between the FE and PE phases and the complex nature of tetragonal tungsten bronze crystal structure can explain the large thermal hysteresis observed at the FE-AFE transition between heating and cooling cycle and the strong depression of the Curie-Weiss temperature T 0 . The semi-phenomenological Ising-like model based on the obtained experimental data is proposed to account for the observed FE-AFE-PE transition sequence

  9. Dielectric and piezoelectric properties of BiFeO3 modified Bi0.5Na0.5TiO3-Bi0.5K0.5TiO3 lead-free piezoelectric ceramics

    International Nuclear Information System (INIS)

    Zhou Changrong; Liu Xinyu; Li Weizhou

    2008-01-01

    The (0.82 - x)Bi 0.5 Na 0.5 TiO 3 -0.18Bi 0.5 K 0.5 TiO 3 -xBiFeO 3 (x = 0-0.07) lead-free piezoelectric ceramics were fabricated by a conventional solid-state reaction method and the effect of BiFeO 3 addition on microstructure and electrical properties of the ceramics was investigated. The specimens with x ≤ 0.05 maintained a rhombohedral-tetragonal phase coexistence and changed into a rhombohedral phase when x > 0.05 in crystal structure. The addition of BiFeO 3 caused a promoted grain growth. All the specimens reveal a low-frequency dielectric dispersion in the frequency range of 40-1 MHz. The piezoelectric constant d 33 and the electromechanical coupling factor k p show an obvious improvement by the addition of small amount of BiFeO 3 , which shows optimum values of d 33 = 170 pC/N and k p = 0.366 at x = 0.03. Contrary to the enhancement of piezoelectric properties, Q m decreases with increasing BiFeO 3 content. The mechanisms of intrinsic and extrinsic contributions to the dielectric and piezoelectric responses have been proposed. Intrinsic contributions are from the relative ion/cation shift that preserves the ferroelectric crystal structure. The remaining extrinsic contributions are from the domain-wall motion and point defects

  10. Gradient stress induced coexistence of tetragonal and rhombohedral phases in Pb(Zr,Ti)O3 films

    International Nuclear Information System (INIS)

    Li Liben; Chen Qingdong; Li Xinzhong; Hu Zhixiang; Zhen Zhiqiang

    2009-01-01

    Thermodynamic theory has been used to explain quantitatively the coexistence of tetragonal and rhombohedral phases in Zr-rich Pb(Zr, Ti)O 3 (PZT) films grown on a compressive substrate. The key is to consider a set of gradient thermal stresses imposed on the films. The 'stress-temperature' phase diagrams were developed for PZT films of several different compositions (Ti/Zr=20/80, 30/70, 40/60, 50/50). The characteristic feature of the phase diagrams for Zr-rich PZT films is the coexistence of tetragonal and rhombohedral phases in the compressive stress region. The volume fractions of the rhombohedral phase were calculated for the Zr-rich PZT films grown on MgO substrate. The result agrees with the experiment.

  11. Zirconia toughened mica glass ceramics for dental restorations.

    Science.gov (United States)

    Gali, Sivaranjani; K, Ravikumar; Murthy, B V S; Basu, Bikramjit

    2018-03-01

    The objective of the present study is to understand the role of yttria stabilized zirconia (YSZ) in achieving the desired spectrum of clinically relevant mechanical properties (hardness, elastic modulus, fracture toughness and brittleness index) and chemical solubility of mica glass ceramics. The glass-zirconia mixtures with varying amounts of YSZ (0, 5, 10, 15 and 20wt.%) were ball milled, compacted and sintered to obtain pellets of glass ceramic-YSZ composites. Phase analysis was carried out using X-ray diffraction and microstructural characterization with SEM revealed the crystal morphology of the composites. Mechanical properties such as Vickers hardness, elastic modulus, indentation fracture toughness and chemical solubility were assessed. Phase analysis of sintered pellets of glass ceramic-YSZ composites revealed the characteristic peaks of fluorophlogopite (FPP) and tetragonal zirconia. Microstructural investigation showed plate and lath-like interlocking mica crystals with embedded zirconia. Vickers hardness of 9.2GPa, elastic modulus of 125GPa, indentation toughness of 3.6MPa·m 1/2 , and chemical solubility of 30μg/cm 2 (well below the permissible limit) were recorded with mica glass ceramics containing 20wt.% YSZ. An increase in hardness and toughness of the glass ceramic-YSZ composites with no compromise on their brittleness index and chemical solubility has been observed. Such spectrum of properties can be utilised for developing a machinable ceramic for low stress bearing inlays, onlays and veneers. Copyright © 2018 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  12. Osteogenesis ability of biomimetic modified 3Y-TZP ceramic using chemical treatment

    Energy Technology Data Exchange (ETDEWEB)

    Hsu, Shih-Kuang [Department of Dental Technology and Materials Science, Central Taiwan University of Science and Technology, Taichung 40601, Taiwan, ROC (China); Chang, Pai-Ling [Taoyuan General Hospital, Taoyuan 33004, Taiwan, ROC (China); Ho, Wen-Fu [Department of Chemical and Materials Engineering, National University of Kaohsiung, Kaohsiung 81148, Taiwan, ROC (China); Hsu, Hsueh-Chuan; Liao, Huei-Jyuan [Department of Dental Technology and Materials Science, Central Taiwan University of Science and Technology, Taichung 40601, Taiwan, ROC (China); Wu, Shih-Ching, E-mail: scwu@ctust.edu.tw [Department of Dental Technology and Materials Science, Central Taiwan University of Science and Technology, Taichung 40601, Taiwan, ROC (China)

    2015-12-01

    In this study, RGD peptide derived from extracellular matrix proteins was employed to modify the surface of yttria-tetragonal zirconia polycrystal (3Y-TZP) to promote cell adhesion. The surface of 3Y-TZP ceramic specimens was first modified using chemical treatment with aqueous solutions of H{sub 3}PO{sub 4}, CH{sub 3}COOH, and NaOH, for the formation of Zr–OH surface functional groups. Then, the RGD peptide was immobilized on the surface of the 3Y-TZP through silanization method, with covalent bonding via the Zr–OH surface functional groups. From this study, the RGD peptide can successfully be grafted onto the chemical modified 3Y-TZP surface. The –OH functional groups formed on the surface of 3Y-TZP after acid/alkaline chemical treatment contribute to the grafting reaction of RGD peptides. The use of phosphoric acid solution in 3Y-TZP surface treatment before RGD peptide grafting for biomimetic modification can significantly enhance cell adhesion, proliferation, and differentiation. - Highlights: • This study successfully immobilized the peptides onto the surface of zirconia. • Acid/alkaline chemical treatment promotes the formation of − OH functional groups. • The use of phosphoric acid solution produced the formation of most − OH. • Peptides can significantly enhance cell adhesion, proliferation, and differentiation.

  13. New Pb(Mg1/3Nb2/3)O3-Pb(In1/2Nb1/2)O3-PbZrO3-PbTiO3 Quaternary Ceramics: Morphotropic Phase Boundary Design and Electrical Properties.

    Science.gov (United States)

    Luo, Nengneng; Zhang, Shujun; Li, Qiang; Xu, Chao; Yang, Zhanlue; Yan, Qingfeng; Zhang, Yiling; Shrout, Thomas R

    2016-06-22

    Four series of Pb(Mg1/3Nb2/3)O3-Pb(In1/2Nb1/2)O3-PbZrO3-PbTiO3 (PMN-PIN-PZ-PT) quaternary ceramics with compositions located at the morphotropic phase boundary (MPB) regions were prepared. The MPBs of the multicomponent system were predicted using a linear combination rule and experimentally confirmed by X-ray powder diffraction and electrical measurement. The positions of MPBs in multicomponent systems were found in linear correlation with the tolerance factor and ionic radii of non-PT end-members. The phase structure, piezoelectric coefficient, electromechanical coupling coefficient, unipolar strains, and dielectric properties of as-prepared ceramics were systematically investigated. The largest d33s were obtained at S36.8, L37.4, M39.6, and N35.8, with the corresponding values of 580, 450, 420, and 530 pC/N, respectively, while the largest kps were found at S34.8, L37.4, M39.6, and N35.8, with the respective values of 0.54, 0.50, 0.47, and 0.53. The largest unipolar strain Smax and high-field piezoelectric strain coefficients d33* were also observed around the respective MPB regions. The rhombohedral-to-tetragonal phase transition temperature Trt increased with increasing PIN and PZ contents. Of particular importance is that high Trt of 140-197 °C was achieved in the M series with PZ and PIN contents being around 0.208 and 0.158, which will broaden the temperature usage range.

  14. Structure and phase formation behavior and dielectric and magnetic properties of lead iron tantalate-lead zirconate titanate multiferroic ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Wongmaneerung, R., E-mail: re_nok@yahoo.com [Faculty of Science, Maejo University, Chiang Mai 50290 (Thailand); Tipakontitikul, R. [Department of Physics, Ubonratchathani University, Ubonratchathani 31490 (Thailand); Jantaratana, P. [Department of Physics, Kasetsart University, Bangkok 10900 (Thailand); Bootchanont, A.; Jutimoosik, J.; Yimnirun, R. [School of Physics, Institute of Science, and NANOTEC-SUT Center of Excellence on Advanced Functional Nanomaterials, Suranaree University of Technology, Nakhon Ratchasima 30000 (Thailand); Ananta, S. [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

    2016-03-15

    Highlights: • The multiferroic ceramics consisted of PFT and PZT. • Crystal structure changed from cubic to mixedcubic and tetragonal with increasing PZT content. • Dielectric showed the samples underwent a typical relaxor ferroelectric behavior. • Magnetic properties showed very interesting behavior with square saturated magnetic hysteresis loops. - Abstract: Multiferroic (1 − x)Pb(Fe{sub 0.5}Ta{sub 0.5})O{sub 3}–xPb(Zr{sub 0.53}Ti{sub 0.47})O{sub 3} (or PFT–PZT) ceramics were synthesized by solid-state reaction method. The crystal structure and phase formation of the ceramics were examined by X-ray diffraction (XRD). The local structure surrounding Fe and Ti absorbing atoms was investigated by synchrotron X-ray Absorption Near-Edge Structure (XANES) measurement. Dielectric properties were studied as a function of frequency and temperature using a LCR meter. A vibrating sample magnetometer (VSM) was used to determine the magnetic hysteresis loops. XRD study indicated that the crystal structure of the sample changed from pure cubic to mixed cubic and tetragonal with increasing PZT content. XANES measurements showed that the local structure surrounding Fe and Ti ions was similar. Dielectric study showed that the samples underwent a typical relaxor ferroelectric behavior while the magnetic properties showed very interesting behavior with square saturated magnetic hysteresis loops.

  15. Disappearance of dielectric anomaly in spite of presence of structural phase transition in reduced BaTiO3: Effect of defect states within the bandgap

    Science.gov (United States)

    Sagdeo, Archna; Nagwanshi, Anjali; Pokhriyal, Preeti; Sinha, A. K.; Rajput, Parasmani; Mishra, Vikash; Sagdeo, P. R.

    2018-04-01

    We report the structural, optical, ferroelectric, and dielectric properties of reduced BaTiO3 samples. For this purpose, oxygen vacancies in BaTiO3 are created by heating these samples with a Ti metal in a vacuum environment at different temperatures. It is observed that with an increase in oxygen deficiencies, the c/a ratio decreases as compared to that of the oxygen treated sample. The ferroelectric properties of the oxygen deficient samples are visibly different as compared to those of the oxygen treated sample. The disappearance of the P-E loop and the anomaly in the temperature variation of the dielectric constant have been observed; however, the structural phase transition corresponding to ferroelectric phase transitions still persists. Thus, it appears that the anomaly in dielectric data and the presence of the P-E loop are getting masked possibly by the Maxwell-Wagner effect. The presence of Ti+3 states in the prepared samples has been confirmed by X-ray absorption near edge structure measurements. The Kubelka-Munk optical absorption shows the presence of extra states below fundamental transition, indicating the emergence of new electronic states within the bandgap, which might be due to Ti+3 states. These new states appear at different energy positions, and with different intensities for different samples, which are reduced in the presence of Ti. These new states within the bandgap appear to modify the electronic structure, thereby reducing the overall bandgap, and hence, they seem to modify the ferroelectric and dielectric properties of the samples. Our results may be treated as experimental evidence for theoretically proposed defect states in oxygen deficient or reduced BaTiO3.

  16. Identifying open-volume defects in doped and undoped perovskite-type LaCoO3, PbTiO3, and BaTiO3

    International Nuclear Information System (INIS)

    Ghosh, Vinita J.; Nielsen, Bent; Friessnegg, Thomas

    2000-01-01

    Dopants, vacancies, and impurity-vacancy clusters have a substantial impact on the properties of perovskite-type metal oxides (general formula ABO 3 ). In order to determine synthesis and processing conditions that optimize the desirable properties of these materials a careful study of these defects is required. It is essential to identify the defects and to map the defect densities. Positron annihilation spectroscopy has often been used to identify vacancy-type defects. Calculations of the positron lifetime and Doppler-broadened profiles of the positron-electron annihilation radiation in undoped and doped LaCoO 3 , PbTiO 3 , and BaTiO 3 are reported, and compared with available experimental data. The results show that these positron techniques are excellent for studying open-volume defects, vacancy-impurity complexes, and for identifying the sublattice occupied by the dopants. (c) 2000 The American Physical Society

  17. Stabilization of metastable tetragonal zirconia nanocrystallites by surface modification

    DEFF Research Database (Denmark)

    Nielsen, Mette Skovgaard; Almdal, Kristoffer; Lelieveld, A. van

    2011-01-01

    Metastable tetragonal zirconia nanocrystallites were studied in humid air and in water at room temperature (RT). A stabilizing effect of different surfactants on the tetragonal phase was observed. Furthermore, the phase stability of silanized metastable tetragonal zirconia nanocrystallites was te...... exposure to humidity. Only silanes and phosphate esters of these were able to stabilize the tetragonal phase in water. Even as small amounts of silanes as 0.25 silane molecule per nm2 are able to stabilize the tetragonal phase in water at RT. Aminopropyl trimethoxy silane and γ...

  18. Superconductivity in an anomalously tetragonal YB2C3O6.62 single crystal: A possible singularity in the structural phase diagram

    DEFF Research Database (Denmark)

    Frello, T.; Andersen, N.H.; Baziljevich, M.

    2003-01-01

    superconducting. This makes the sample highly anomalous in two respects: with a stoichiometry of YBa2Cu3O6.62 the sample should have an orthorhombic symmetry, and a tetragonal undoped sample should not be superconducting at all. Our results corroborate previous findings of Topnikov [JETP Lett. 46, 577 (1987......)] of a tetragonal superconducting YBCO crystal with x=0.62....

  19. Structural and dielectric characteristics of donor dopants in A and B places of perovskite ceramic PZT 54/46

    International Nuclear Information System (INIS)

    Durruthy-Rodriguez, M.D.; Perez-Fernandez, L.D.; Pelaiz-Barranco, A.; Calderon-Pinar, F.

    2009-01-01

    The microstructural (XRD and SEM) and dielectric behavior of Pb(Zr 0.54 Ti 0.46 )O 3 (PZT 54/46) ceramic system with donor (La, Nb and La+Nb) doping was studied. For all Nb-doped PZT samples, only one (tetragonal) phase was found, which confirms the compositional shifts near the morphotropic phase boundary. For La- and La+Nb-doped samples, there are two (rhombohedral and tetragonal) phases. Dielectric characteristic behavior (1/ε) for La- and La+Nb-doped PZT was associated with two-phase transitions: Ferro-Ferro at low temperature and Ferro-Para at Curie temperature. For Nb-doped samples, only one phase transition is observed, which indicates the presence of a single ferroelectric phase. (orig.)

  20. Patterned solid state growth of barium titanate crystals

    Science.gov (United States)

    Ugorek, Michael Stephen

    An understanding of microstructure evolution in ceramic materials, including single crystal development and abnormal/enhanced grain growth should enable more controlled final ceramic element structures. In this study, two different approaches were used to control single crystal development in a patterned array. These two methods are: (1) patterned solid state growth in BaTiO 3 ceramics, and (2) metal-mediated single crystal growth in BaTiO 3. With the patterned solid state growth technique, optical photolithography was used to pattern dopants as well as [001] and [110] BaTiO3 single crystal template arrays with a 1000 microm line pattern array with 1000 microm spacings. These patterns were subsequently used to control the matrix grain growth evolution and single crystal development in BaTiO3. It was shown that the growth kinetics can be controlled by a small initial grain size, atmosphere conditions, and the introduction of a dopant at selective areas/interfaces. By using a PO2 of 1x10-5 atm during high temperature heat treatment, the matrix coarsening has been limited (to roughly 2 times the initial grain size), while retaining single crystal boundary motion up to 0.5 mm during growth for dwell times up to 9 h at 1300°C. The longitudinal and lateral growth rates were optimized at 10--15 microm/h at 1300°C in a PO2 of 1x10 -5 atm for single crystal growth with limited matrix coarsening. Using these conditions, a patterned microstructure in BaTiO3 was obtained. With the metal-mediated single crystal growth technique, a novel approach for fabricating 2-2 single crystal/polymer composites with a kerf texture development were studied using both [001] and [110] BaTiO3 single crystals templates. By using a PO 2 of 1x10-11 atm during high temperature heat treatment, matrix coarsening was limited while enabling single crystal boundary motion up to 0.35 mm during growth between 1250°C and 1300°C with growth rates ˜ 3--4 microm/h for both single crystal orientations. By

  1. Effects of MnO{sub 2} doping on structure, dielectric and piezoelectric properties of 0.825NaNbO{sub 3}-0.175Ba{sub 0.6}(Bi{sub 0.5}K{sub 0.5}){sub 0.4}TiO{sub 3} lead-free ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Fan, Ximing; Lin, Dunmin; Zheng, Qiaoji; Sun, Hailing; Wan, Yang; Wu, Xiaochun [College of Chemistry and Materials Science, and Visual Computing and Virtual Reality Key Laboratory of Sichuan Province, Sichuan Normal University, Chengdu 610066 (China); Wu, Lang [State Key Laboratory Cultivation Base for Nonmetal Composites and Functional Materials, Southwest University of Science and Technology, Mianyang 621010 (China)

    2012-12-15

    Lead-free ceramics 0.825NaNbO{sub 3}-0.175Ba{sub 0.6}(Bi{sub 0.5}K{sub 0.5}){sub 0.4}TiO{sub 3} + xmol% MnO{sub 2} were prepared by an ordinary sintering technique and the effects of MnO{sub 2} doping on the structure, dielectric, and piezoelectric properties of the ceramics were studied. The ceramics with perovskite structure are transformed from tetragonal to pseudocubic phases by increasing the doping level of MnO{sub 2}. After the addition of MnO{sub 2}, the Curie temperature T{sub C} of the ceramics decreases and the ferroelectric-paraelectric phase transition at T{sub C} becomes more diffusive. Because of the donor and acceptor doping effects of Mn ions simultaneously, the piezoelectric constant d{sub 33}, electromechanical coupling coefficient k{sub p}, relative permittivity {epsilon}{sub r}, and mechanical quality factor Q{sub m} are enhanced considerably after the addition of 1 mol% MnO{sub 2}. The ceramic with 1 mol% MnO{sub 2} doping possesses the optimum piezoelectricity (d{sub 33} = 131 pC/N and k{sub p} = 21.8%) and relatively high Q{sub m} = 627. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  2. Phase transitions and electrical characterizations of (K 0.5Na 0.5) 2x(Sr 0.6Ba 0.4) 5-xNb 10O 30 (KNSBN) ceramics with 'unfilled' and 'filled' tetragonal tungsten-bronze (TTB) crystal structure

    KAUST Repository

    Yao, Yingbang

    2012-12-01

    Alkali-doped strontium barium niobate (K 0.5Na 0.5) 2x(Sr 0.6Ba 0.4) 5-xNb 10O 30 (KNSBN) ceramics has been prepared by a conventional solid-state reaction method. The alkali-dopant concentration x has been varied from 0.24 to 1.15 so that the crystal structure was transformed from \\'unfilled\\' to \\'filled\\' tetragonal tungsten-bronze (TTB) structure. Apart from the change in the structural properties, the effects of the alkali-dopants on the phase transition as well as ferroelectric, piezoelectric and pyroelectric properties have also been investigated. Phase transitions have been studied in the temperature range of -200°C to 350°C. The origins of these phase transitions are discussed. The addition of the alkali-dopants enhances the ferroelectric, piezoelectric and pyroelectric properties of the KNSBN ceramics. Alkali-doping also favors abnormal grain growth and thus results in a porous microstructure, which might contribute to the enhancement of the pyroelectric performance. © 2012 Elsevier Ltd.

  3. Phase transitions and electrical characterizations of (K 0.5Na 0.5) 2x(Sr 0.6Ba 0.4) 5-xNb 10O 30 (KNSBN) ceramics with 'unfilled' and 'filled' tetragonal tungsten-bronze (TTB) crystal structure

    KAUST Repository

    Yao, Yingbang; Mak, C. L.; Ploss, Bernd

    2012-01-01

    Alkali-doped strontium barium niobate (K 0.5Na 0.5) 2x(Sr 0.6Ba 0.4) 5-xNb 10O 30 (KNSBN) ceramics has been prepared by a conventional solid-state reaction method. The alkali-dopant concentration x has been varied from 0.24 to 1.15 so that the crystal structure was transformed from 'unfilled' to 'filled' tetragonal tungsten-bronze (TTB) structure. Apart from the change in the structural properties, the effects of the alkali-dopants on the phase transition as well as ferroelectric, piezoelectric and pyroelectric properties have also been investigated. Phase transitions have been studied in the temperature range of -200°C to 350°C. The origins of these phase transitions are discussed. The addition of the alkali-dopants enhances the ferroelectric, piezoelectric and pyroelectric properties of the KNSBN ceramics. Alkali-doping also favors abnormal grain growth and thus results in a porous microstructure, which might contribute to the enhancement of the pyroelectric performance. © 2012 Elsevier Ltd.

  4. Phase transformation in multiferroic Bi{sub 5}Ti{sub 3}FeO{sub 15} ceramics by temperature-dependent ellipsometric and Raman spectra: An interband electronic transition evidence

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, P. P.; Duan, Z. H.; Xu, L. P.; Zhang, X. L.; Li, Y. W.; Hu, Z. G., E-mail: zghu@ee.ecnu.edu.cn; Chu, J. H. [Key Laboratory of Polar Materials and Devices, Ministry of Education, Department of Electronic Engineering, East China Normal University, Shanghai 200241 (China)

    2014-02-28

    Thermal evolution and an intermediate phase between ferroelectric orthorhombic and paraelectric tetragonal phase of multiferroic Bi{sub 5}Ti{sub 3}FeO{sub 15} ceramic have been investigated by temperature-dependent spectroscopic ellipsometry and Raman scattering. Dielectric functions and interband transitions extracted from the standard critical-point model show two dramatic anomalies in the temperature range of 200–873 K. It was found that the anomalous temperature dependence of electronic transition energies and Raman mode frequencies around 800 K can be ascribed to intermediate phase transformation. Moreover, the disappearance of electronic transition around 3 eV at 590 K is associated with the conductive property.

  5. Quantifying Local and Cooperative Components in the Ferroelectric Distortion of BaTiO3: Learning from the Off-Center Motion in the MnCl65– Complex Formed in KCl:Mn+

    DEFF Research Database (Denmark)

    García Lastra, Juan Maria; García-Fernández, P.; Calle-Vallejo, F.

    2014-01-01

    → C4v → Oh local transformations occurring in the 10–50 K temperature range for the MnCl65– complex formed in KCl:Mn+ that mimic the behavior of BaTiO3. From Boltzmann analysis of the vibronic levels derived from ab initio calculations and considering decoherence introduced by random strains......, the present calculations reproduce the experimental phase sequence and transition temperatures. Furthermore, our calculations show that the off-center instability in KCl:Mn+ would be suppressed by reducing by only 1% the lattice parameter, a situation that then becomes comparable to that found for BaTiO3...

  6. Spatially modulated magnetic structure of EuS due to the tetragonal domain structure of SrTiO3 APS

    CERN Document Server

    Rosenberg, Aaron J.; Kirtley, John R.; Gedik, Nuh; Moodera, Jagadeesh S.; Moler, Kathryn A.

    2017-12-15

    The combination of ferromagnets with topological superconductors or insulators allows for new phases of matter that support excitations such as chiral edge modes and Majorana fermions. EuS, a wide-bandgap ferromagnetic insulator with a Curie temperature around 16 K, and SrTiO3 (STO), an important substrate for engineering heterostructures, may support these phases. We present scanning superconducting quantum interference device measurements of EuS grown epitaxially on STO that reveal micron-scale variations in ferromagnetism and paramagnetism. These variations are oriented along the STO crystal axes and only change their configuration upon thermal cycling above the STO cubic-to-tetragonal structural transition temperature at 105 K, indicating that the observed magnetic features are due to coupling between EuS and the STO tetragonal structure. We speculate that the STO tetragonal distortions may strain the EuS, altering the magnetic anisotropy on a micron scale. This result demonstrates that local variation in...

  7. Texture of poled tetragonal PZT detected by synchrotron X-ray diffraction and micromechanics analysis

    International Nuclear Information System (INIS)

    Hall, D.A.; Steuwer, A.; Cherdhirunkorn, B.; Withers, P.J.; Mori, T.

    2005-01-01

    The texture and lattice elastic strain due to electrical poling of tetragonal PZT (lead zirconate titanate) ceramics have been measured using high energy synchrotron X-ray diffraction. It is shown that XRD peak intensity ratios associated with crystal planes of the form {002}, {112} and {202} exhibit a linear dependence on cos-bar 2 Ψ, where Ψ represents the orientation angle between the plane normal and the macroscopic poling axis. The observed dependence of texture and lattice strain on the grain orientation can be understood on the basis that the macroscopic strain due to poling is the average of the poling strains of all the individual grains

  8. Giant strain with low cycling degradation in Ta-doped [Bi{sub 1/2}(Na{sub 0.8}K{sub 0.2}){sub 1/2}]TiO{sub 3} lead-free ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xiaoming; Tan, Xiaoli, E-mail: xtan@iastate.edu [Department of Materials Science and Engineering, Iowa State University, Ames, Iowa 50011 (United States)

    2016-07-21

    Non-textured polycrystalline [Bi{sub 1/2}(Na{sub 0.8}K{sub 0.2}){sub 1/2}](Ti{sub 1−x}Ta{sub x})O{sub 3} ceramics are fabricated and their microstructures and electrical properties are characterized. Transmission electron microscopy reveals the coexistence of the rhombohedral R3c and tetragonal P4bm phases in the form of nanometer-sized domains in [Bi{sub 1/2}(Na{sub 0.8}K{sub 0.2}){sub 1/2}]TiO{sub 3} with low Ta concentration. When the composition is x = 0.015, the electrostrain is found to be highly asymmetric under bipolar fields of ±50 kV/cm. A very large value of 0.62% is observed in this ceramic, corresponding to a large-signal piezoelectric coefficient d{sub 33}* of 1240 pm/V (1120 pm/V under unipolar loading). These values are greater than most previously reported lead-free polycrystalline ceramics and can even be compared with some lead-free piezoelectric single crystals. Additionally, this ceramic displays low cycling degradation; its electrostrain remains above 0.55% even after undergoing 10 000 cycles of ±50 kV/cm bipolar fields at 2 Hz. Therefore, Ta-doped [Bi{sub 1/2}(Na{sub 0.8}K{sub 0.2}){sub 1/2}]TiO{sub 3} ceramics show great potential for large displacement devices.

  9. Temperature stability and electrical properties in La-doped KNN-based ceramics

    KAUST Repository

    Lv, Xiang; Wu, Jiagang; Zhu, Jianguo; Xiao, Dingquan; Zhang, Xixiang

    2018-01-01

    To improve the temperature stability and electrical properties of KNN‐based ceramics, we simultaneously consider the phase boundary and the addition of rare earth element (La), 0.96K0.5Na0.5Nb0.96Sb0.04O3‐0.04(Bi1‐xLax)0.5Na0.5ZrO3 (0 ≤ x ≤ 1.0) ceramics. More specifically, we investigate how the phase boundary and the addition of La3+ affect the phase structure, electrical properties, and temperature stability of the ceramic. We show that increasing the La3+ content leads to a change in phase structure, from a rhombohedral‐tetragonal (R‐T) phase coexistence to a cubic phase. More importantly, we show that the appropriate addition of La3+ (x = 0.2) can simultaneously improve the unipolar strain (from 0.127% to 0.147%) and the temperature stability (i.e., the unipolar strain of 0.147% remains unchanged when T is increased from 25 to 80°C). In addition, we find that the ceramics with x = 0.2 exhibit a large piezoelectric constant (d33) of ~430 pC/N, a high Curie temperature (TC) of ~240°C and a fatigue‐free behavior (after 106 electric cycles). The enhanced electrical properties mostly originate from the easy domain switching, whereas the improved temperature stability can be attributed to the R‐T phase boundary and the appropriate addition of La3+.

  10. Temperature stability and electrical properties in La-doped KNN-based ceramics

    KAUST Repository

    Lv, Xiang

    2018-04-16

    To improve the temperature stability and electrical properties of KNN‐based ceramics, we simultaneously consider the phase boundary and the addition of rare earth element (La), 0.96K0.5Na0.5Nb0.96Sb0.04O3‐0.04(Bi1‐xLax)0.5Na0.5ZrO3 (0 ≤ x ≤ 1.0) ceramics. More specifically, we investigate how the phase boundary and the addition of La3+ affect the phase structure, electrical properties, and temperature stability of the ceramic. We show that increasing the La3+ content leads to a change in phase structure, from a rhombohedral‐tetragonal (R‐T) phase coexistence to a cubic phase. More importantly, we show that the appropriate addition of La3+ (x = 0.2) can simultaneously improve the unipolar strain (from 0.127% to 0.147%) and the temperature stability (i.e., the unipolar strain of 0.147% remains unchanged when T is increased from 25 to 80°C). In addition, we find that the ceramics with x = 0.2 exhibit a large piezoelectric constant (d33) of ~430 pC/N, a high Curie temperature (TC) of ~240°C and a fatigue‐free behavior (after 106 electric cycles). The enhanced electrical properties mostly originate from the easy domain switching, whereas the improved temperature stability can be attributed to the R‐T phase boundary and the appropriate addition of La3+.

  11. The influence of mechanical activation on the morphological changes of Fe/BaTiO_3 powder

    International Nuclear Information System (INIS)

    Kosanović, D.; Obradović, N.; Pavlović, V.P.; Marković, S.; Maričić, A.; Rasić, G.; Vlahović, B.; Pavlović, V.B.; Ristić, M.M.

    2016-01-01

    Highlights: • Fe/BaTiO_3 ceramic was prepared using a solid-state reaction. • Powder mixture of 60% Fe and 40% BaTiO_3 was mechanically activated up to 240 min. • Microstructure was characterized using Powder XRD and SEM. • Thermal stability of the activated samples was investigated using DSC. • Raman spectrum changes with activation, along with atypical resonant scattering. - Abstract: Crystal structure and morphology of mechanically activated nanocrystalline Fe/BaTiO_3 was investigated using a combination of spectroscopic and microscopic methods. These show that mechanical activation led to the creation of new surfaces and the comminution of the initial powder particles. Prolonged milling resulted in formation of larger agglomerates of BaTiO_3 and bimodal particle size distribution, where BaTiO_3 particles were significantly larger than those of iron-containing phases. Milling times of 210 min and above lead to a significant decrease in temperature of the oxidation of iron in the sample, indicating abrupt change in reactivity. Raman spectroscopy analysis has revealed that activation had a pronounced influence on Fe/BaTiO_3 lattice, thereby affecting both the stability of the crystal structure and the phase transition phenomena.

  12. Influence of microstructure on electromechanical properties of nano-crystalline La-Pb(Ni{sub 1/3}Sb{sub 2/3})-PbZrTiO{sub 3} ferroelectric ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, H.H.; Lonkar, C.M. [Armament Research and Development Establishment, Pune (India); Balasubramanian, K. [Defence Institute of Advanced Technology (Deemed University), Pune (India)

    2017-10-15

    A ferroelectric ceramic composition, Pb{sub 0.98}La{sub 0.02}(Ni{sub 1/3}Sb{sub 2/3}){sub 0.05}[(Zr{sub 0.52}Ti{sub 0.48}){sub 0.995}] {sub 0.95}O{sub 3}, has been synthesized by columbite precursor method followed by mechanical activation for 10 h (MA-10) using high-energy ball mill. Formation of desired perovskite phase during activation was confirmed from analysis of X-ray diffraction patterns, while powder particle size, in nano-meter range, was revealed from high-resolution transmission electron microscopic (HRTEM) investigations. Samples were sintered between 1170 and 1320 C, and were investigated for microstructure and its influence on electromechanical properties. Increment in grain size with sintering temperature was noticed. 1220 C sintering temperature posed denser and uniform microstructure amongst all the temperatures and also showed composition close to morphotropic phase boundary (MPB) of PZT with optimum tetragonality which resulted in better electromechanical properties, suggesting the suitability of this composition for power harvesting applications. Phase transition studies revealed normal ferroelectric behaviour with transition temperature of 286 C. (orig.)

  13. Bulletin of Materials Science | News

    Indian Academy of Sciences (India)

    Effect of temperature and time on solvothermal synthesis of tetragonal BaTiO3 ... Chitosan–silver oxide nanocomposite film: Preparation and antimicrobial activity .... surface coatings on wood impregnated with Cu-ethanolamine preservatives .... Structure and electric transport properties of LnSr2FeTiO7 (Ln = La, Nd and Gd).

  14. Structural and Chemical Analysis of the Zirconia-Veneering Ceramic Interface.

    Science.gov (United States)

    Inokoshi, M; Yoshihara, K; Nagaoka, N; Nakanishi, M; De Munck, J; Minakuchi, S; Vanmeensel, K; Zhang, F; Yoshida, Y; Vleugels, J; Naert, I; Van Meerbeek, B

    2016-01-01

    The interfacial interaction of veneering ceramic with zirconia is still not fully understood. This study aimed to characterize morphologically and chemically the zirconia-veneering ceramic interface. Three zirconia-veneering conditions were investigated: 1) zirconia-veneering ceramic fired on sandblasted zirconia, 2) zirconia-veneering ceramic on as-sintered zirconia, and 3) alumina-veneering ceramic (lower coefficient of thermal expansion [CTE]) on as-sintered zirconia. Polished cross-sectioned ceramic-veneered zirconia specimens were examined using field emission gun scanning electron microscopy (Feg-SEM). In addition, argon-ion thinned zirconia-veneering ceramic interface cross sections were examined using scanning transmission electron microscopy (STEM)-energy dispersive X-ray spectrometry (EDS) at high resolution. Finally, the zirconia-veneering ceramic interface was quantitatively analyzed for tetragonal-to-monoclinic phase transformation and residual stress using micro-Raman spectroscopy (µRaman). Feg-SEM revealed tight interfaces for all 3 veneering conditions. High-resolution transmission electron microscopy (HRTEM) disclosed an approximately 1.0-µm transformed zone at sandblasted zirconia, in which distinct zirconia grains were no longer observable. Straight grain boundaries and angular grain corners were detected up to the interface of zirconia- and alumina-veneering ceramic with as-sintered zirconia. EDS mapping disclosed within the zirconia-veneering ceramic a few nanometers thick calcium/aluminum-rich layer, touching the as-sintered zirconia base, with an equally thick silicon-rich/aluminum-poor layer on top. µRaman revealed t-ZrO2-to-m-ZrO2 phase transformation and residual compressive stress at the sandblasted zirconia surface. The difference in CTE between zirconia- and the alumina-veneering ceramic resulted in residual tensile stress within the zirconia immediately adjacent to its interface with the veneering ceramic. The rather minor chemical

  15. Structural, thermal, and optical properties of Er3+/Yb3+ co-doped oxyhalide tellurite glasses, glass-ceramics and ceramics

    International Nuclear Information System (INIS)

    Joshi, C.; Rai, R.N.; Rai, S.B.

    2012-01-01

    Glass-ceramics and ceramics containing nano-crystals of different phases doped with Er 3+ /Yb 3+ ions have been successfully prepared by heat treatment of the precursor oxyhalide glasses synthesized by the melt-quench method. X-ray diffraction patterns and transmission electron microscopy (TEM) images verify the precipitation of nano-crystals. Emission of Er 3+ enhances several times when Yb 3+ ion is added with the matrix. The Stark splitting and the intensity of different emission bands increase to a great extent when we approach to ceramics from glasses via glass-ceramics. The intensity of the blue and green emission bands increases much faster than the red and NIR emission bands. Intense upconversion emission observed by the naked eye has been quantified in terms of standard chromaticity diagram (CIE). Power dependence study shows that the upconversion of NIR radiation to visible radiation takes place mainly via photon avalanche (PA) process.

  16. Highly constrained ferroelectric [BaTiO3](1−x)Λ/[BaZrO3]xΛ superlattices: X-ray diffraction and Raman spectroscopy

    International Nuclear Information System (INIS)

    Belhadi, J.; El Marssi, M.; Gagou, Y.; El Mendili, Y.; Bouyanfif, H.; Yuzyuk, Yu. I.; Raevski, I. P.; Wolfman, J.

    2014-01-01

    We report an x-ray diffraction (XRD) and a Raman-scattering investigation of ferroelectric/paraelectric superlattices [BaTiO 3 ] (1−x)Λ /[BaZrO 3 ] xΛ for which the composition varied, 0.15 ≤ x ≤ 0.85, while the superlattice (SL) modulation period Λ was kept constant at about 100 Å. The samples were epitaxially grown by pulsed laser deposition on MgO substrates buffered with La 0.5 Sr 0.5 CoO 3 . Based on the XRD analysis and on polarized Raman spectra, we have showed that the large strain in SLs induced ferroelectricity in BaZrO 3 (BZ) for all SLs, a material that is paraelectric in the bulk form at any temperature and in the single film. The induced polar axis in BZ layers is perpendicular to the plane of substrate while BaTiO 3 (BT) layers exhibit in-plane polar orientation. Raman spectroscopy revealed a lattice ordering in SLs due to the misfit strain generated by the large lattice mismatch between the alternating BZ and BT layers. This strain induced a huge upward frequency of the lowest E(1TO) soft mode from 60 cm −1 in the BT single film to 215 cm −1 in the SL with x = 0.85. These results show that in spite of relatively large periodicity of SLs, they are highly constrained and the variation of BZ ratio allowed modifying strains between layers. The temperature dependence of the Raman spectra for BT 0.3Λ /BZ 0.7Λ and BT 0.7Λ /BZ 0.3Λ samples revealed giant shift of the ferroelectric phase transition. The phase transition temperature was found to be upshifted by about 300 °C with respect to BT single crystal.

  17. Studies on zirconia-mullite ceramic

    International Nuclear Information System (INIS)

    Virkar, Alka N.

    2014-01-01

    Zirconia Toughened Alumina (ZTA) ceramics with much improved Fracture Toughness and Strength have been used as a front material to fabricate composite Armour-Applications, Al 2 O 3 has very different fluxing ability with silica by sufficiently lowering the melting point. Addition of small amount of Fe 2 O 3 , TiO 2 , in an Al 2 O 3 -SiO 2 mixture enhances needle shaped Mullite crystal growth and also assist Liquid phase Sintering. In the present investigation, Zircon was used as a source of ZrO 2 and SiO 2 . Zircon (ZrSiO 4 ) has a low coefficient of Thermal Expansion and good Thermal Shock Resistance. Densification in terms of Relative Density and App. Porosity, Tetragonal ZrO 2 , phases, Thermal Expansion Coefficient, Hardness etc. were studied on Zirconia-Mullite system with and without additives. Z-M system with Y 2 O 3 additives show improved properties owing to the partial stabilization of Zirconia phase (PSZ). (author)

  18. The preparation of dental glass-ceramic composites with controlled fraction of leucite crystals

    Directory of Open Access Journals (Sweden)

    Martina Mrázová

    2008-06-01

    Full Text Available This work is dealing with synthesis of leucite powder, which can be used for the preparation of dental glassceramic composites by subsequent thermal treatment. Newly developed procedure is based on preparation of dental raw material as a mixture of two separate compounds: the crystalline leucite powder prepared at relatively low temperature and a commercial matrix powder.Hydrothermal synthesis of tetragonal leucite particles (KAlSi2O6 with the average size of about 3 μm was developed in our laboratory. The leucite dental raw material was prepared by mixing of 20 wt.% of synthetic tetragonal leucite with commercial matrix. Dental composites were prepared from the dental raw material by uniaxial pressing and firing up to 960°C. Dilatometric measurements confirmed that the coefficient of thermal expansion increased by 32% when 20 wt.% of the tetragonal leucite was added into the basic matrix. In addition, it was showed that the synthesized leucite powder was suitable for the preparation of leucite composites with controlled coefficient of thermal expansion. High value of the thermal expansion coefficient enables application of prepared composite in metal-ceramics restorations.

  19. Influence of cooling rate on residual stress profile in veneering ceramic: measurement by hole-drilling.

    Science.gov (United States)

    Mainjot, Amélie K; Schajer, Gary S; Vanheusden, Alain J; Sadoun, Michaël J

    2011-09-01

    The manufacture of dental crowns and bridges generates residual stresses within the veneering ceramic and framework during the cooling process. Residual stress is an important factor that control the mechanical behavior of restorations. Knowing the stress distribution within the veneering ceramic as a function of depth can help the understanding of failures, particularly chipping, a well-known problem with Yttria-tetragonal-zirconia-polycrystal based fixed partial dentures. The objective of this study is to investigate the cooling rate dependence of the stress profile in veneering ceramic layered on metal and zirconia frameworks. The hole-drilling method, often used for engineering measurements, was adapted for use with veneering ceramic. The stress profile was measured in bilayered disc samples 20 mm in diameter, with a 0.7 mm thick metal or Yttria-tetragonal-zirconia-polycrystal framework and a 1.5mm thick veneering ceramic. Three different cooling procedures were investigated. The magnitude of the stresses in the surface of the veneering ceramic was found to increase with cooling rate, while the interior stresses decreased. At the surface, compressive stresses were observed in all samples. In the interior, compressive stresses were observed in metal samples and tensile in zirconia samples. Cooling rate influences the magnitude of residual stresses. These can significantly influence the mechanical behavior of metal-and zirconia-based bilayered systems. The framework material influenced the nature of the interior stresses, with zirconia samples showing a less favorable stress profile than metal. Copyright © 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  20. Modelização e estudo experimental de óxidos multiferróicos

    CERN Document Server

    Fenta, Abel

    The main goal of this work was the theoretical and experimental study of multiferroics oxides. This particular approach focused mainly on the ferroelectric material barium titanate. The essence of this theoretical study is the ab initio calculation of hiperfine parameters using the Wien2k software. This software, which uses the selfconsistent $LAPW$ method to solve the Kohn-Sham equations, allowed to determine the electric field gradient and the BaTiO$_3$ system’s total energy in its different structural phases, and study its behaviour in function of the different lattice parameters. The modeling of stratified systems of the (XTiO$_3$).(BaTiO$_3$)$_{n-1}$ and (BaZO$_3$).(BaTiO$_3$ )$_{n-1}$, with X=Cd and Hg and Z=Fe, from n=2 to n=6 type, built from the experimental latice parameters (formula) in the tetragonal sage was also made. This simulation can be related to the physical situation of the epitaxial growth of XTiO$_3$ a layer on n BaTiO$_3$ layers. It was also studied the effect of the Cd ion volume di...

  1. An investigation of neutron irradiation test on superplastic zirconia-ceramic materials

    International Nuclear Information System (INIS)

    Shibata, Taiju; Ishihara, Masahiro; Baba, Shinichi; Hayashi, Kimio

    2000-05-01

    A neutron irradiation test on superplastic ceramic materials at high temperature has been proposed as an innovative basic research on high-temperature engineering using the High Temperature Engineering Test Reactor (HTTR). For the effective execution of the test, we reviewed the superplastic deformation mechanism of ceramic materials and discussed neutron irradiation effects on the superplastic deformation process of stabilized Tetragonal Zirconia Polycrystal (TZP), which is a representative superplastic ceramic material. As a result, we pointed out that the decrease in the activation energy for superplastic deformation is expected by the radiation-enhanced diffusion. We selected a fast neutron fluence of 5x10 20 n/cm 2 and an irradiation temperature of about 600degC as test conditions for the first irradiation test on TZP and decided to perform a preliminary irradiation test by the Japan Materials Testing Reactor (JMTR). Moreover, we estimated the radioactivity of irradiated TZP and indicated that it is in the order of 10 10 Bq/g (about 0.3 Ci/g) immediately after irradiation to a thermal neutron fluence of 3x10 20 n/cm 2 and that it decays to about 1/100 in a year. (author)

  2. Tetragonal-cubic phase boundary in nanocrystalline ZrO{sub 2}-Y{sub 2}O{sub 3} solid solutions synthesized by gel-combustion

    Energy Technology Data Exchange (ETDEWEB)

    Fabregas, Ismael O. [CINSO (Centro de Investigaciones en Solidos), CITEFA-CONICET, J.B. de La Salle 4397, 1603 Villa Martelli, Pcia. de Buenos Aires (Argentina); Craievich, Aldo F.; Fantini, Marcia C.A. [Instituto de Fisica, Universidade de Sao Paulo, Travessa R da Rua do Matao, No. 187, Cidade Universitaria, 05508-900 Sao Paulo (Brazil); Millen, Ricardo P.; Temperini, Marcia L.A. [Instituto de Quimica, Universidade de Sao Paulo, Avenida Prof. Lineu Prestes 748, Cidade Universitaria, 05508-900 Sao Paulo (Brazil); Lamas, Diego G., E-mail: dlamas@uncoma.edu.ar [CINSO (Centro de Investigaciones en Solidos), CITEFA-CONICET, J.B. de La Salle 4397, 1603 Villa Martelli, Pcia. de Buenos Aires (Argentina); Laboratorio de Caracterizacion de Materiales, Facultad de Ingenieria, Universidad Nacional del Comahue, Buenos Aires 1400, (8300) Neuquen Capital, Prov. de Neuquen (Argentina)

    2011-04-21

    Research highlights: > Gel-combustion synthesis yields compositionally homogeneous, single-phased ZrO{sub 2}-Y{sub 2}O{sub 3} nanopowders, that exhibit the presence at room temperature of three different phases depending on Y{sub 2}O{sub 3} content, namely two tetragonal forms (t' and t'') and the cubic phase. > Phase identification can be achieved by synchrotron XPD (SXPD) and Raman spectroscopy since the tetragonal forms and the cubic phase can be distinguished by these techniques. > The crystallographic features of ZrO{sub 2}-Y{sub 2}O{sub 3} nanopowders were determined by SXPD. They are similar to those reported by Yashima and coworkers for compositionally homogeneous materials containing larger (micro)crystals. However, the lattice parameters are slightly different and the axial ratios c/a of our t' samples are smaller than those reported by these authors. > Compositional t'/t'' and t''/cubic phase boundaries are located at (9 {+-} 1) and (10.5 {+-} 0.5) mol% Y{sub 2}O{sub 3}, respectively. > For the whole series of nanocrystalline ZrO{sub 2}-Y{sub 2}O{sub 3} solid solutions studied in the present work, no evidences of the presence of a mixture of phases - as reported by Yashima and coworkers for microcrystalline solid solutions - were detected. - Abstract: By means of synchrotron X-ray powder diffraction (SXPD) and Raman spectroscopy, we have detected, in a series of nanocrystalline and compositionally homogeneous ZrO{sub 2}-Y{sub 2}O{sub 3} solid solutions, the presence at room temperature of three different phases depending on Y{sub 2}O{sub 3} content, namely two tetragonal forms and the cubic phase. The studied materials, with average crystallite sizes within the range 7-10 nm, were synthesized by a nitrate-citrate gel-combustion process. The crystal structure of these phases was also investigated by SXPD. The results presented here indicate that the studied nanocrystalline ZrO{sub 2}-Y{sub 2}O{sub 3} solid

  3. Shape and phase evolution from CsPbBr3 perovskite nanocubes to tetragonal CsPb2Br5 nanosheets with an indirect bandgap.

    Science.gov (United States)

    Li, Guopeng; Wang, Hui; Zhu, Zhifeng; Chang, Yajing; Zhang, Ting; Song, Zihang; Jiang, Yang

    2016-09-13

    Tetragonal CsPb 2 Br 5 nanosheets were obtained by an oriented attachment of orthorhombic CsPbBr 3 nanocubes, involving a lateral shape evolution from octagonal to square. Meanwhile, the experimental results, together with DFT simulation results, indicated that the tetragonal CsPb 2 Br 5 is an indirect bandgap semiconductor that is PL-inactive with a bandgap of 2.979 eV.

  4. Flight-vehicle materials, structures, and dynamics - Assessment and future directions. Vol. 3 - Ceramics and ceramic-matrix composites

    Science.gov (United States)

    Levine, Stanley R. (Editor)

    1992-01-01

    The present volume discusses ceramics and ceramic-matrix composites in prospective aerospace systems, monolithic ceramics, transformation-toughened and whisker-reinforced ceramic composites, glass-ceramic matrix composites, reaction-bonded Si3N4 and SiC composites, and chemical vapor-infiltrated composites. Also discussed are the sol-gel-processing of ceramic composites, the fabrication and properties of fiber-reinforced ceramic composites with directed metal oxidation, the fracture behavior of ceramic-matrix composites (CMCs), the fatigue of fiber-reinforced CMCs, creep and rupture of CMCs, structural design methodologies for ceramic-based materials systems, the joining of ceramics and CMCs, and carbon-carbon composites.

  5. Single crystal growth of 67%BiFeO3-33%BaTiO3 solution by the floating zone method

    Science.gov (United States)

    Rong, Y.; Zheng, H.; Krogstad, M. J.; Mitchell, J. F.; Phelan, D.

    2018-01-01

    The growth conditions and the resultant grain morphologies and phase purities from floating-zone growth of 67%BiFeO3-33%BaTiO3 (BF-33BT) single crystals are reported. We find two formidable challenges for the growth. First, a low-melting point constituent leads to a pre-melt zone in the feed-rod that adversely affects growth stability. Second, constitutional super-cooling (CSC), which was found to lead to dendritic and columnar features in the grain morphology, necessitates slow traveling rates during growth. Both challenges were addressed by modifications to the floating-zone furnace that steepened the temperature gradient at the melt-solid interfaces. Slow growth was also required to counter the effects of CSC. Single crystals with typical dimensions of hundreds of microns have been obtained which possess high quality and are suitable for detailed structural studies.

  6. Single crystal growth of 67%BiFeO 3 -33%BaTiO 3 solution by the floating zone method

    Energy Technology Data Exchange (ETDEWEB)

    Rong, Y.; Zheng, H.; Krogstad, M. J.; Mitchell, J. F.; Phelan, D.

    2018-01-01

    The growth conditions and the resultant grain morphologies and phase purities from floating-zone growth of 67%BiFeO3-33%BaTiO3 (BF-33BT) single crystals are reported. We find two formidable challenges for the growth. First, a low-melting point constituent leads to a pre-melt zone in the feed-rod that adversely affects growth stability. Second, constitutional super-cooling (CSC), which was found to lead to dendritic and columnar features in the grain morphology, necessitates slow traveling rates during growth. Both challenges were addressed by modifications to the floating-zone furnace that steepened the temperature gradient at the melt-solid interfaces. Slow growth was also required to counter the effects of CSC. Single crystals with typical dimensions of hundreds of microns have been obtained which possess high quality and are suitable for detailed structural studies.

  7. Preparation and optical properties of gold-dispersed BaTiO3 thin films

    Energy Technology Data Exchange (ETDEWEB)

    Kineri, T; Mori, M [TDK Corp., Tokyo (Japan). R and D Center; Kadono, K; Sakaguchi, T; Miya, M; Wakabayashi, H [Osaka National Research Inst., Osaka (Japan); Tsuchiya, T [Science Univ. of Tokyo, Tokyo (Japan). Faculty of Industrial Science and Technology

    1993-12-01

    Recently, metal or semiconductor-doped glasses were widely studied because of their large resonant third-order nonlinearity. These glasses are utilized in an optical information field as all optical logic devices in the future. The gold-doped glass films or thin layers have a large third-order nonlinear susceptibility [chi] and are prepared by r.f. sputtering method, etc. The optical properties, particularly the refractive index or dielectric constant of the matrix, are very important for the optical nonlinearity of these materials. In this study, gold-dispersed BaTiO3 thin films and gold-dispersed SiO2 thin films are prepared using r.f. magnetron sputtering method, and the optical properties of the films are compared. The [chi] of the films are measured and the effect of the matrix of the films on [chi] is investigated. The headings in the paper are: Introduction, Experimental procedure, Results, Discussion, and Conclusion. 13 refs., 9 figs.

  8. Pyroelectrically Induced Pyro-Electro-Chemical Catalytic Activity of BaTiO3 Nanofibers under Room-Temperature Cold–Hot Cycle Excitations

    OpenAIRE

    Yuntao Xia; Yanmin Jia; Weiqi Qian; Xiaoli Xu; Zheng Wu; Zichen Han; Yuanting Hong; Huilin You; Muhammad Ismail; Ge Bai; Liwei Wang

    2017-01-01

    A pyro-electro-chemical catalytic dye decomposition using lead-free BaTiO3 nanofibers was realized under room-temperature cold–hot cycle excitation (30–47 °C) with a high Rhodamine B (RhB) decomposition efficiency ~99%, which should be ascribed to the product of pyro-electric effect and electrochemical redox reaction. Furthermore, the existence of intermediate product of hydroxyl radical in pyro-electro-chemical catalytic process was also observed. There is no significant decrease in pyro-ele...

  9. Characterization of Conventional and High-Translucency Y-TZP Dental Ceramics Submitted to Air Abrasion.

    Science.gov (United States)

    Tostes, Bhenya Ottoni; Guimarães, Renato Bastos; Noronha-Filho, Jaime Dutra; Botelho, Glauco Dos Santos; Guimarães, José Guilherme Antunes; Silva, Eduardo Moreira da

    2017-01-01

    This study evaluated the effect of air-abrasion on t®m phase transformation, roughness, topography and the elemental composition of three Y-TZP (Yttria-stabilized tetragonal zirconia polycrystal) dental ceramics: two conventional (Lava Frame and IPS ZirCad) and one with high-translucency (Lava Plus). Plates obtained from sintered blocks of each ceramic were divided into four groups: AS (as-sintered); 30 (air-abrasion with 30 mm Si-coated Al2O3 particles); 50 (air-abrasion with 50 mm Al2O3 particles) and 150 (air-abrasion with 150 mm Al2O3 particles). After the treatments, the plates were submitted to X-ray diffractometry; 3-D profilometry and SEM/EDS. The AS surfaces were composed of Zr and t phases. All treatments produced t®m phase transformation in the ceramics. The diameter of air-abrasion particles influenced the roughness (150>50>30>AS) and the topography. SEM analysis showed that the three treatments produced groove-shaped microretentions on the ceramic surfaces, which increased with the diameter of air-abrasion particles. EDS showed a decrease in Zr content along with the emergence of O and Al elements after air-abrasion. Presence of Si was also detected on the plates air-abraded with 30 mm Si-coated Al2O3 particles. It was concluded that irrespective of the type and diameter of the particles, air-abrasion produced t®m phase transformation, increased the roughness and changed the elemental composition of the three Y-TZP dental ceramics. Lava Plus also behaved similarly to the conventional Y-TZP ceramics, indicating that this high translucency ceramic could be more suitable to build monolithic ceramic restorations in the aesthetic restorative dentistry field.

  10. Relationship between tolerance factor and temperature coefficient of permittivity of temperature-stable high permittivity BaTiO3–Bi(MeO3 compounds

    Directory of Open Access Journals (Sweden)

    Natthaphon Raengthon

    2016-03-01

    Full Text Available The temperature coefficient of permittivity (TCε of BaTiO3–Bi(MeO3 solid solutions were investigated. It was determined that as the tolerance factor was decreased with the addition of Bi(MeO3, the TCε shifted from large negative values to TCε values approaching zero. It is proposed that the different bonding nature of the dopant cation affects the magnitude and temperature stability of the permittivity. This study suggests that the relationship between tolerance factor and TCε can be used as a guide to design new dielectric compounds exhibiting temperature-stable high permittivity characteristics, which is similar to past research on perovskite and pyrochlore-based microwave dielectrics.

  11. First-principles comparison of the cubic and tetragonal phases of Mo3Sb7

    KAUST Repository

    Nazir, Safdar; Auluck, Sushil V.; Pulikkotil, Jiji Thomas Joseph; Singh, Nirpendra; Schwingenschlö gl, Udo

    2011-01-01

    Using ab initio density functional based methods, we study the normal metal state properties of the ∼3 K Mo3Sb7 superconductor, in its high temperature cubic and low temperature tetragonal structures. Although the density of states at the Fermi energy is reasonably high in both structures, our calculations unequivocally show that there exists no long range magnetic ordering in this system. We also address the optical properties of the compound. The magnetism in Mo3Sb7 is studied by fixed spin moment calculations, which yield a shallow non-magnetic minimum, thus inferring propensity to a magnetic instability. © 2011 Elsevier B.V. All rights reserved.

  12. First-principles comparison of the cubic and tetragonal phases of Mo3Sb7

    KAUST Repository

    Nazir, Safdar

    2011-03-01

    Using ab initio density functional based methods, we study the normal metal state properties of the ∼3 K Mo3Sb7 superconductor, in its high temperature cubic and low temperature tetragonal structures. Although the density of states at the Fermi energy is reasonably high in both structures, our calculations unequivocally show that there exists no long range magnetic ordering in this system. We also address the optical properties of the compound. The magnetism in Mo3Sb7 is studied by fixed spin moment calculations, which yield a shallow non-magnetic minimum, thus inferring propensity to a magnetic instability. © 2011 Elsevier B.V. All rights reserved.

  13. Synthesis and electrical conductivity of nanocrystalline tetragonal FeS

    International Nuclear Information System (INIS)

    Zeng Shu-Lin; Wang Hui-Xian; Dong Cheng

    2014-01-01

    A convenient method for synthesis of tetragonal FeS using iron powder as iron source, is reported. Nanocrystalline tetragonal FeS samples were successfully synthesized by reacting metallic iron powder with sodium sulfide in acetate buffer solution. The obtained sample is single-phase tetragonal FeS with lattice parameters a = 0.3767 nm and c = 0.5037 nm, as revealed by X-ray diffraction. The sample consists of flat nanosheets with lateral dimensions from 20 nm up to 200 nm and average thickness of about 20 nm. We found that tetragonal FeS is a fairly good conductor from the electrical resistivity measurement on a pellet of the nanosheets. The temperature dependence of conductivity of the pellet was well fitted using an empirical equation wherein the effect of different grain boundaries was taken into consideration. This study provides a convenient, economic way to synthesize tetragonal FeS in a large scale and reports the first electrical conductivity data for tetragonal FeS down to liquid helium temperature. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  14. Electrical characterization and impedance response of lanthanum doped barium titanate ceramics

    Directory of Open Access Journals (Sweden)

    Mančić D.

    2008-01-01

    Full Text Available The dielectric permittivity and dissipation factor of La-doped and undoped BaTiO3 were investigated as a function of frequency and temperature. The impedance response was used to study the electrical properties of La-doped BaTiO3 over the temperature range from room temperature (RT to 350°C. La-doped and undoped BaTiO3, obtained by a modified Pechini method, were sintered in air at 1300°C for 2 and 16 hours. The impedance spectra were analyzed in terms of equivalent circuits involving resistors, capacitors and constant phase elements (CPE. The most suitable electrical circuit for the interpretation of experimental results is found to be the equivalent circuit consisting of resistors and CPE elements which replace the capacitor elements. The contribution of grain boundary resistance to the total resistance of a system is remarkable at low temperature. Dielectric permittivity of doped BaTiO3 was in the range of 8000 to 12000 at 1 kHz and the dissipation factor was less than 1%.

  15. Raman scattering intensities in BaTiO3 and PbTiO3 prototypical ferroelectrics from density functional theory

    International Nuclear Information System (INIS)

    Hermet, P; Veithen, M; Ghosez, Ph

    2009-01-01

    Nonlinear optical susceptibilities and Raman scattering spectra of the ferroelectric phases of BaTiO 3 and PbTiO 3 are computed using a first-principles approach based on density functional theory and taking advantage of a recent implementation based on the nonlinear response formalism and the 2n+1 theorem. These two prototypical ferroelectric compounds were chosen to demonstrate the accuracy of the Raman calculation based both on their complexity and their technological importance. The computation of the Raman scattering intensities has been performed not only for the transverse optical modes, but also for the longitudinal optical ones. The agreement between the measured and computed Raman spectra of these prototypical ferroelectrics is remarkable for both the frequency position and the intensity of Raman lines. This agreement presently demonstrates the state-of-the-art in the computation of Raman responses on one of the most complex systems, ferroelectrics, and constitutes a step forward in the reliable prediction of their electro-optical responses.

  16. Synthesis and characterization of BaTi1−xSnxO3–0.5 mol%GeO2

    International Nuclear Information System (INIS)

    Bucur, Raul Alin; Bucur, Alexandra Ioana; Novaconi, Stefan; Nicoara, Irina

    2012-01-01

    Highlights: ► BaTi 1−x Sn x O 3 –0.5 mol%GeO 2 (x = 0, 0.1, 0.3, 0.5) ceramics were prepared at 1190 °C. ► GeO 2 improves crystallization and densification. ► Anomalies are noted for the rhombohedral–orthorhombic transition of BT–0.5Ge. ► For x = 0.3 and 0.5, ε′ r exhibit nearly constant variation between 200 and 400 K. - Abstract: Microcrystalline BaTi 1−x Sn x O 3 –0.5 mol%GeO 2 x = 0, 0.1, 0.3, 0.5 (BTSx–0.5Ge) and BaTiO 3 (BT) ceramics (1–0.5 μm) were prepared by a conventional solid-state reaction method. The crystalline structure of the samples was examined using XRD, the microstructure was analyzed by means of electron microscope and the density was measured by the Archimede’s method. The sintered ceramic disks have a tetragonal symmetry for BT, pseudo cubic for BTS1–0.5Ge and cubic symmetry for the other studied materials, with a gradual increase of unit cell dimensions. Small addition of GeO 2 can improve the density of BT ceramics: 97.9% for BT–0.5Ge, and 96.21% for pure BT. The highest degree of densification in the case of tin doping is achieved for BTS1–0.5Ge (96.93%). The formation of a liquid phase can lead to an anomalous grain growth, and in the case of BT–0.5Ge the grains are completely surrounded by a frozen eutectic melt. For the dielectric constant, while increasing the Sn concentration, the T C gradually shifts towards lower temperatures, and the peak of this transition becomes broader. The lowering of T C is mostly due to the concentration of tin ions and in a much delicate way to Ge ions. Anomalies are noticed for the orthorhombic transition, where the permittivity is higher than the same transition of the matrix (BT), with a shift towards higher temperatures. The BTS3–0.5Ge and BTS5–0.5Ge are the most stable compositions in terms of dielectric behavior, since in the temperature range 200–400 K, ε′ r is almost constant. Therefore, these compositions can be used for devices that operate over a

  17. Texture and anisotropy in the bismuth sodium titanate system

    Science.gov (United States)

    Fancher, Christoher M.

    Bi0.5Na0.5TiO3 has received interest as a potential replacement for lead containing ferroelectrics. However, the piezoelectric response of pure Bi0.5Na0.5TiO 3 does not compare to the strong piezoelectric response of lead based piezoelectrics. To increase the piezoelectric response, Bi0.5Na 0.5TiO3 has been alloyed with BaTiO3 and K 0.5Na0.5NbO3. Another route to enhance the response is to take advantage of the anisotropic properties by inducing a preferred crystallographic orientation. Both routes were used to investigate the effect a crystallographic texture has on the strain response of Bi0.5Na 0.5TiO3-based ceramics. A crystallographic texture was induced by templated grain growth of pure phase Bi0.5Na0.5TiO3 templates using the tape casting method to orient template particles relative to the tape cast normal. Sintered Bi0.5Na0.5TiO3-based materials developed a strong (00l)pc fiber texture relative to the tape cast normal, with no preferential alignment relative to the tape cast plane. Textured Bi0.5Na0.5TiO3-(5)BaTiO3 showed a piezoelectric response of 245 pC/N, a better than 50% enhancement from the 150 pC/N response of randomly oriented samples. The Bi0.5Na0.5TiO3-(5)BaTiO3-(2)K 0.5Na0.5NbO3 (x,y) system has been shown to undergo electric-field-induced phase transformation from a pseudocubic to polar phase. For (7,2) a strong 8.7 multiples of a random distribution (MRD) crystallographic texture increased the macroscopic strain response by 50%. Applying the electric field perpendicular to the fiber texture axis reduces the macroscopic strain response of textured (7,2) by 17%. The affect field direction has on the electric-field-induced phase transformations of textured (7,2) was investigated using in situ electric field dependent diffraction. In situ diffraction data showed the high strain response of textured (7,2) can be attributed to a reversible pseudocubic to tetragonal transformation. The field-induced tetragonal phase nucleates preferentially with a

  18. Phase coexistence and high piezoelectric properties in (K0.40Na0.60)0.96Li0.04Nb0.80Ta0.20O3 ceramics

    International Nuclear Information System (INIS)

    Wu Ling; Zhang Jialiang; Shao Shoufu; Zheng Peng; Wang Chunlei

    2008-01-01

    Lead-free (K x Na 1-x ) 0.96 Li 0.04 Nb 0.80 Ta 0.20 O 3 ceramics with x = 0.10-0.70 were prepared by the conventional solid-state reaction technique. The influence of the K/Na ratio on the microstructure, crystallographic structure, phase transition and piezoelectric properties was investigated. It has been disclosed that the phase transition temperature T O-T drastically decreases with x in the narrow compositional range of x 0.30-0.40 and the phase coexistence of the orthorhombic structure and the tetragonal structure occurs near x = 0.40. The ceramics with x = 0.40 shows high piezoelectric properties (d 33 = 254 pC N -1 , k p = 51.5%, k t = 49.4% and k 33 = 66.6%, respectively) with low dielectric loss (tan δ 1.5%) and weak temperature dependence between 10 and 85 deg. C. In particular, the piezoelectric properties remain almost unchanged in the thermal ageing test from -125 to 300 deg. C. Therefore, this ceramic is considered to be a very promising lead-free piezoelectric material for practical applications. The relation of piezoelectric properties with morphotropic phase boundary and polymorphic phase transition was discussed

  19. Vacancy-induced magnetism in BaTiO3(001) thin films based on density functional theory.

    Science.gov (United States)

    Cao, Dan; Cai, Meng-Qiu; Hu, Wang-Yu; Yu, Ping; Huang, Hai-Tao

    2011-03-14

    The origin of magnetism induced by vacancies on BaTiO(3)(001) surfaces is investigated systematically by first-principles calculations within density-functional theory. The calculated results show that O vacancy is responsible for the magnetism of the BaO-terminated surface and the magnetism of the TiO(2)-terminated surface is induced by Ti vacancy. For the BaO-terminated surface, the magnetism mainly arises from the unpaired electrons that are localized in the O vacancy basin. In contrast, for the TiO(2)-terminated surface, the magnetism mainly originates from the partially occupied O-2p states of the first nearest neighbor O atoms surrounding the Ti vacancy. These results suggest the possibility of implementing magneto-electric coupling in conventional ferroelectric materials.

  20. ADVANCED CERAMIC MATERIALS FOR DENTAL APPLICATIONS SINTERED BY MICROWAVE HEATING

    OpenAIRE

    Presenda Barrera, Álvaro

    2016-01-01

    [EN] Zirconia has become a widely utilized structural ceramic material with important applications in dentistry due to its superb mechanical properties, biocompatibility, aesthetic characteristics and durability. Zirconia needs to be stabilized in the t-phase to obtain improved mechanical properties such as hardness and fracture toughness. Fully dense yttria-stabilized tetragonal zirconia polycrystalline (Y-TZP) materials are normally consolidated through the energy-intensive processing of po...

  1. The Study on Thermal Expansion of Ceramic Composites with Addition of ZrW[2]O]8

    OpenAIRE

    Dedova, Elena Sergeevna; Shadrin, V. S.; Petrushina, M. Y.; Kulkov, Sergey Nikolaevich

    2016-01-01

    The studies on structure, phase composition and thermal properties of (Al[2]O[3] - 20 wt% ZrO[2]) - ZrW[2]O[8] ceramic composites obtained using nanosized, initial powders were conducted. Homogeneously distributed white particles on the polished surface of composites were observed. Phase composition of the composites was represented with corundum, monoclinic ZrO[2] and two modifications of ZrW[2]O[8] (tetragonal and cubic). Linear thermal expansion coefficient values of the composites were de...

  2. Phase transition characteristics and associated piezoelectricity of potassium-sodium niobate lead-free ceramics.

    Science.gov (United States)

    Wang, Yuanyu; Hu, Liang; Zhang, Qilong; Yang, Hui

    2015-08-14

    To achieve high piezoelectric activity and a wide sintering temperature range, the ceramic system concerning (1 - x)(K(0.48)Na(0.52))(Nb(0.96)Sb(0.04))O(3)-x[Bi(0.5)(Na(0.7)Ag(0.3))(0.5)](0.90) Zn(0.10)ZrO(3) was designed, and the rhombohedral-tetragonal (R-T) phase boundary can drive a high d(33). Phase transition characteristics as well as their effects on the electrical properties were investigated systematically. The R-T coexistence phase boundary (0.04 ≤ x ≤ 0.05) can be driven via modification with BNAZZ, and has been confirmed by XRD and temperature-dependent dielectric constants as well as Raman analysis, and the ceramics possess enhanced piezoelectric properties (d(33) ∼ 425 pC N(-1) and k(p) ∼ 0.43) and a high unipolar strain (∼0.3%). In addition, a wide sintering temperature range of 1050-1080 °C can warrant a large d(33) of 400-430 pC N(-1), which can benefit practical applications. As a result, the addition of BNAZZ is an effective method to improve the electrical properties (piezoelectricity and strain) and sintering behavior of potassium-sodium niobate ceramics.

  3. Impedance spectroscopy of Li2CO3 doped (Ba,Sr)TiO3 ceramic

    Science.gov (United States)

    Ham, Yong-Su; Koh, Jung-Hyuk

    2013-02-01

    (BaxSr1-x)TiO3-based ceramic has been considered as one of the most important electronic materials widely employed in microwave passive device applications. Many researches have been performed to lower the high sintering temperature, by adding various dopants such as B2O3, La2O3, etc. In our previous study, by adding Li2CO3 to (Ba0.5,Sr0.5)TiO3 ceramics, the sintering temperature of Li2CO3 doped (Ba0.5,Sr0.5)TiO3 ceramics decreased from 1350 to 900 °C. This study observed the crystalline structure and electrical properties of Li2CO3 doped (Ba0.5,Sr0.5)TiO3 ceramics. In scanning the crystalline structure of Li2CO3 doped (Ba0.5,Sr0.5)TiO3 ceramics, no pyro phase was observed by X-ray diffraction analysis. To investigate the electrical properties of Li2CO3 doped (Ba0.5,Sr0.5)TiO3 ceramics, real and imaginary parts of the impedances were analyzed. Complex impedance data were measured from 100 Hz to 1 MHz at various temperature ranges.

  4. Crystal structure of the tetragonal polymorph of bis(1-ethyl-3-methylimidazolium tetrabromidocadmate

    Directory of Open Access Journals (Sweden)

    Tamara Đorđević

    2016-07-01

    Full Text Available Both unique Cd atoms in the tetragonal polymorph of bis(1-ethyl-3-methylimidazolium tetrabromidocadmate, (C6H11N22[CdBr4], occupy special positions (site symmetry -4. The crystal structure consists of isolated tetrahedral [CdBr4]2− anions which are surrounded by 1-ethyl-3-methylimidazolium cations. The methyl and ethyl side chains of the cations show positional disorder in a 0.590 (11:0.410 (11 ratio. In the crystal, (C6H11N2+ cations display three weak C—H...Br hydrogen-bond interactions through the imidazolium ring H atoms with the Br− ligands of the surrounding complex anions. The alkyl groups of the side chains are not involved in hydrogen bonding.

  5. A preliminary X-ray diffraction study of the tetragonal superconducting oxide LaBa2Cu3O7-δ

    International Nuclear Information System (INIS)

    Hervieu, M.; Nguyen, N.; Michel, C.

    1987-01-01

    X-ray diffraction study of LaBa 2 Cu 3 O 7-δ showed that this tetragonal oxide exhibits an ordered oxygen deficient perovskite structure. It appears that the oxygen vacancy distribution differs from that observed for the orthorhombic superconductor YBa 2 Cu 3 O 7-δ . A structural model is proposed and discussed [fr

  6. On the nature of phase transitions in the tetragonal tungsten bronze GdK{sub 2}Nb{sub 5}O{sub 15} ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Gagou, Y.; Lukyanchuk, I.; El Marssi, M., E-mail: mimoun.elmarssi@u-picardie.fr [Laboratoire de Physique de la Matière Condensée, Université de Picardie Jules Verne, 33 rue Saint-Leu, 80039 Amiens Cedex (France); Amira, Y. [Laboratoire de Physique de la Matière Condensée, Université de Picardie Jules Verne, 33 rue Saint-Leu, 80039 Amiens Cedex (France); Laboratoire de la Matière Condensée et Nanostructures, FSTG, Université Cadi Ayyad Marrakech, Maroc (Morocco); Mezzane, D. [Laboratoire de la Matière Condensée et Nanostructures, FSTG, Université Cadi Ayyad Marrakech, Maroc (Morocco); Courty, M.; Masquelier, C. [Laboratoire de Réactivité et Chimie des Solides, UMR 7314, Université de Picardie Jules Verne, Pôle Scientifique, 33 rue Saint-Leu, 80039 Amiens Cedex 1 (France); Yuzyuk, Yu. I. [Faculty of Physics, Southern Federal University, 5, Zorge Str. Rostov-on-Don 344090 (Russian Federation)

    2014-02-14

    Phase transitions in gadolinium potassium niobate GdK{sub 2}Nb{sub 5}O{sub 15} (GKN) ceramics have been investigated by x-ray diffraction, dielectric susceptibility, differential scanning calorimetry, and Raman scattering. The results of our complementary studies show that GKN exhibits two phase transitions at T{sub c1} = 238 °C and T{sub c2} = 375 °C attributed to the ferroelectric-antiferroelectric-paraelectric (FE-AFE-PE) phase transitions. According to the x-ray diffraction analysis, the FE and PE phases were refined in the polar P4bm and centrosymmetric P4/mbm space groups. For the intermediate phase, the structure is refined in the space group P4nc with doubling of the c unit cell parameter, which is compatible with an AFE phase. This result was confirmed by Raman spectroscopy since new low-frequency lines are activated in the AFE phase due to the Brillouin zone-folding effect, typical for the modulated phases. The presence of the AFE phase between the FE and PE phases and the complex nature of tetragonal tungsten bronze crystal structure can explain the large thermal hysteresis observed at the FE-AFE transition between heating and cooling cycle and the strong depression of the Curie-Weiss temperature T{sub 0}. The semi-phenomenological Ising-like model based on the obtained experimental data is proposed to account for the observed FE-AFE-PE transition sequence.

  7. Non-ohmic phenomena in Mn-doped BaTiO3

    International Nuclear Information System (INIS)

    Prades, Marta; Beltran, Hector; Cordoncillo, Eloisa; Alonso, Pablo J.; Maso, Nahum; West, Anthony R.

    2012-01-01

    We report here a novel effect in which the resistance of a semiconducting oxide ceramic increases on application of a small dc bias. The ceramic conducts at high temperatures by an n-type hopping mechanism. On application of a dc bias, conduction electrons are trapped at surface states and the resistance increases. On removal of the dc bias, the trapped electrons are released and the sample regains its original state. This effect is the mirror image of that seen with similar ceramics that conduct by a p-type mechanism whose resistance decreases reversibly on application of a small dc bias. These two phenomena together offer the possibility of novel switching devices and memristive applications, especially if the switching times can be reduced. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  8. Microstructural evolution and stability of tetragonal precipitates in Y2O3 partially-stabilized ZrO2 single crystals

    International Nuclear Information System (INIS)

    Martinez-Fernandez, J.; Jimenez-Melendo, M.; Dominguez-Rodriguez, A.

    1995-01-01

    The microstructure and morphology of tetragonal precipitates (t-ZrO 2 ) in yttria partially-stabilized zirconia single crystals containing various amounts of Y 2 O 3 (3, 4, 4.7 and 5.8 mol%) have been studied as a function of aging time at 1,600 C in air. The precipitate size and volume fraction of t-ZrO 2 phase were determined using transmission electron microscopy. The evolution of the precipitate volume fraction with aging time indicated that the precipitation reaction was completed after 24 h of annealing, in agreement with the values of the Y 2 O 3 composition in the matrix measured by analytical electron microscopy. Further aging coarsened the precipitates which joined together forming fiber-like particles of several micrometers in length and remaining untransformed despite their large size. The stability of the t-ZrO 2 precipitates against the tetragonal to monoclinic transformation in the ZrO 2 -Y 2 O 3 system seems to be related to interactions between precipitates due to coherency stresses rather than with their morphological characteristics

  9. Polymorphic phase transition and morphotropic phase boundary in Ba{sub 1-x}Ca{sub x}Ti{sub 1-y}Zr{sub y}O{sub 3} ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Abdessalem, M. Ben; Aydi, S.; Aydi, A.; Abdelmoula, N.; Khemakhem, H. [Universite de Sfax, Faculte des Sciences de Sfax (FSS), Laboratoire des Materiaux Multifonctionnels et Applications (LaMMA) LR16ES18, B.P.1171, Sfax (Tunisia); Sassi, Z. [Laboratoire de Genie Electrique et Ferroelectricite (LGEF) de L' INSA de Lyon, Lyon (France)

    2017-09-15

    This paper deals with Ca and Zr co-doped BaTiO{sub 3} (BCTZ{sub (x,} {sub y)}) (x = 0.1, 0.13, 0.2 and y = 0.05, 0.1, 0.15). These ceramics were prepared using the conventional solid state method. The symmetry, dielectric properties, Raman spectroscopy, ferroelectric behavior and piezoelectric effect were examined. X-ray diffraction (XRD) results display that morphotropic boundary occurs from tetragonal to orthorhombic region of BCZT{sub (x=0.1,} {sub 0.2,} {sub y=0.05,} {sub 0.1)} and polymorphic phase transitions from tetragonal to orthorhombic, orthorhombic to rhombohedral regions of BCZT{sub (x=0.13,} {sub y=0.1)}. The evolution of the Raman spectra was investigated as a function of compositions at room temperature, in correlation with XRD analysis and dielectric measurements. We note that the substitution of Ca in Ba site and Zr ions in Ti site slightly decreased the cubic-tetragonal temperature transition (T{sub C}) and increased the orthorhombic-tetragonal (T{sub 1}) and rhombohedral-orthorhombic (T{sub 2}) temperatures transitions. The ferroelectric properties were examined by a P-E hysteresis loop. The two parameters ΔT{sub 1} and ΔT{sub 2} are defined as ΔT{sub 1} = T{sub C} - T{sub 1} and ΔT{sub 2} = T{sub C} - T{sub 2}, they come close to T{sub C} for x = 0.13, y = 0.1, which reveals that this composition is around the polymorphic phase. The excellent piezoelectric coefficient of d{sub 33} = 288 pC N{sup -1}, the electromechanical coupling factor k{sub p} = 40%, high constant dielectric 9105, coercive field E{sub c} = 0.32 (KV mm{sup -1}) and remanent polarization P{sub r} = 0.1 (μc mm{sup -2}) were obtained for composition x = 0.13, y = 0.1. (orig.)

  10. Structure and dielectric properties of (Ba{sub 0.7}Sr{sub 0.3}){sub 1-x}Na{sub x}(Ti{sub 0.9}Sn{sub 0.1}){sub 1-x}Nb{sub x}O{sub 3} ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Ghoudi, Hanen; Khirouni, Kamel [Universite de Gabes, Laboratoire de Physique des Materiaux et des Nanomateriaux Appliquee a l' Environnement (La Phy MNE), Faculte des Sciences de Gabes, Gabes (Tunisia); Chkoundali, Souad [Universite de Sfax, Laboratoire des Materiaux Multifonctionnels et Applications (LaMMA), Faculte des Sciences de Sfax (FSS), Sfax (Tunisia); Aydi, Abdelhedi [Universite de Gabes, Laboratoire de Physique des Materiaux et des Nanomateriaux Appliquee a l' Environnement (La Phy MNE), Faculte des Sciences de Gabes, Gabes (Tunisia); Universite de Sfax, Laboratoire des Materiaux Multifonctionnels et Applications (LaMMA), Faculte des Sciences de Sfax (FSS), Sfax (Tunisia)

    2017-11-15

    (Ba{sub 0.7}Sr{sub 0.3}){sub 1-x}Na{sub x}(Ti{sub 0.9}Sn{sub 0.1}){sub 1-x}Nb{sub x}O{sub 3} ceramics with compositions x = 0.6, 0.7, 0.8 and 0.9 were synthesized using the solid-state reaction method. These ceramics were examined by X-ray diffraction and dielectric measurements over a broad temperature and frequency ranges. X-ray diffraction patterns revealed a single-perovskite phase crystallized in a cubic structure, for x < 0.8, and in tetragonal, for x ≥ 0.8, with Pm3m and P4mm spaces groups, respectively. Two types of behaviors, classical ferroelectric or relaxor, were observed depending on the x composition. It is noted that temperatures T{sub C} (the Curie temperature) or T{sub m} (the temperature of maximum permittivity) rise when x increases and the relaxor character grows more significantly when x composition decreases. To analyze the dielectric relaxation degree of relaxor, various models were considered. It was proven that an exponential function could well describe the temperature dependence of the static dielectric constant and relaxation time. (orig.)

  11. Bi4Sr3Ca3Cu4O16 galss and superconducting glass ceramics

    International Nuclear Information System (INIS)

    Zheng, H.; Mackenzie, J.D.

    1988-01-01

    Bi 4 Sr 3 Ca 3 Cu 4 O 16 glass has been successfully fabricated by the melting process. Glass transition temperature, crystallization temperature, and liquid temperature of the glass are 434, 478, and 833 0 C, respectively. After the glass is heat treated at 800 0 C, a glass ceramic is formed. A comparison of the x-ray-diffraction pattern of the superconducting Bi 4 Sr 3 Ca 3 Cu 4 O/sub 16+//sub x/ ceramic to the Bi 4 Sr 3 Ca 3 Cu 4 O 16 glass ceramic revealed preferred orientation in the glass ceramic crystals. The superconducting transition temperatures T/sub c//sub (onset)/ and T/sub c//sub (zero)/ of the glass ceramics are 100 and 45 K, respectively

  12. Synthesis of new perovskite and ''tetragonal bronze'' materials with thorium

    International Nuclear Information System (INIS)

    Launay, Suzanne; Erb, Alfred; Freundlich, William

    1982-01-01

    Disclosure and crystal chemistry study of the solid solutions Th(NbO 3 ) 4 , NaNbO 3 or AgNbO 3 with perovskite structure and Th(Nb, TaO 3 ) 4 , K(Nb,Ta)O 3 with ''tetragonal tungstene bronze'' structure, ''Banana'' type [fr

  13. Fabrication and in vitro biological properties of piezoelectric bioceramics for bone regeneration

    Science.gov (United States)

    Tang, Yufei; Wu, Cong; Wu, Zixiang; Hu, Long; Zhang, Wei; Zhao, Kang

    2017-02-01

    The piezoelectric effect of biological piezoelectric materials promotes bone growth. However, the material should be subjected to stress before it can produce an electric charge that promotes bone repair and reconstruction conducive to fracture healing. A novel method for in vitro experimentation of biological piezoelectric materials with physiological load is presented. A dynamic loading device that can simulate the force of human motion and provide periodic load to piezoelectric materials when co-cultured with cells was designed to obtain a realistic expression of piezoelectric effect on bone repair. Hydroxyapatite (HA)/barium titanate (BaTiO3) composite materials were fabricated by slip casting, and their piezoelectric properties were obtained by polarization. The d33 of HA/BaTiO3 piezoelectric ceramics after polarization was 1.3 pC/N to 6.8 pC/N with BaTiO3 content ranging from 80% to 100%. The in vitro biological properties of piezoelectric bioceramics with and without cycle loading were investigated. When HA/BaTiO3 piezoelectric bioceramics were affected by cycle loading, the piezoelectric effect of BaTiO3 promoted the growth of osteoblasts and interaction with HA, which was better than the effect of HA alone. The best biocompatibility and bone-inducing activity were demonstrated by the 10%HA/90%BaTiO3 piezoelectric ceramics.

  14. Dilatometric and dielectric behaviour of Sm modified PCT ceramics

    International Nuclear Information System (INIS)

    Singh, Sarabjit; Thakur, O.P.; Prakash, Chandra; Raina, K.K.

    2005-01-01

    Samarium modified PCT ceramics with composition (Pb 0.76-x Sm x Ca 0.24 )(Ti 0.98 Mn 0.02 )O 3 ; x=0-0.08 in steps of 0.02 were prepared by conventional mixed-oxide method. Detailed dilatometric studies were carried out for green specimens in order to study sintering behaviour. Change in the dilatometric behaviour is correlated with the XRD results of powders calcined at different temperatures. Dielectric constant was observed to increase with increasing Sm concentration, which has been attributed to reduced tetragonality and better densification on Sm substitution. SEM micrographs have revealed the grain size of the samples. Ferroelectric hysteresis behaviour was studied for all the compositions

  15. Effects of multiple firings on the microstructure of zirconia and veneering ceramics.

    Science.gov (United States)

    Alkurt, Murat; Yeşil Duymus, Zeynep; Gundogdu, Mustafa

    2016-01-01

    The aim of study was to evaluate the effects of multiple firings on the microstructures of zirconia and two ceramics. Vita VM9 (VMZ) and Cerabien ZR (C-Z) ceramics on a zirconia framework and zirconia without veneering ceramic (WO-Z) were evaluated. Firing methods included firing two, five, and ten times (n=10). The effects of multiple firings on the surface hardness of the materials were evaluated using a Vickers hardness (HV) tester. Data were analyzed by two-way ANOVA and Tukey's test (α=0.05). After firing five and ten times, the hardness of VM-Z and C-Z increased significantly (p0.05). In the XRD analysis, zirconia had similar tetragonal (t)-monoclinic (m) phase transformations of Y-TZP after the different firing times. Clinically, multiple firings did not affect the microstructure of zirconia, but the structures of the two ceramics were affected.

  16. Electric field-induced phase transitions and composition-driven nanodomains in rhombohedral-tetragonal potassium-sodium niobate-based ceramics

    KAUST Repository

    Lv, Xiang; Wu, Jiagang; Xiao, Dingquan; Zhu, Jianguo; Zhang, Xixiang

    2017-01-01

    -T) phase boundary, confirmed using several advanced techniques, allowed a large piezoelectric constant (d33) of 450 ± 5 pC/N to be obtained in (1-x)K0.4Na0.6Nb0.945Sb0.055O3-xBi0.5Na0.5(Hf1-ySny)O3 (0 ≤ x ≤ 0.06 and 0 ≤ y ≤ 0.5) ceramics possessing

  17. Enhanced active piezoelectric 0-3 nanocomposites fabricated through electrospun nanowires

    International Nuclear Information System (INIS)

    Feenstra, Joel; Sodano, Henry A.

    2008-01-01

    The use of monolithic piezoceramic materials in sensing and actuation applications has become quite common over the past decade. However, these materials have several properties that limit their application in practical systems. These materials are very brittle due to the ceramic nature of the monolithic material, making them vulnerable to accidental breakage during handling and bonding procedures. In addition, they have very poor ability to conform to curved surfaces and result in large add-on mass associated with using a typically lead-based ceramic. These limitations have motivated the development of alternative methods of applying the piezoceramic material, including piezoceramic fiber composites and piezoelectric 0-3 composites (also known as piezoelectric paint). Piezoelectric paint is desirable because it can be spayed or painted on and can be used with abnormal surfaces. However, the piezoelectric paint developed in prior studies has resulted in low coupling, limiting its application. In order to increase the coupling of the piezoelectric paint, this effort has investigated the use of piezoelectric nanowires rather than spherical piezoelectric particle, which are difficult to strain when embedded in a polymer matrix. The piezoceramic wires were electrospun from a barium titanate (BaTiO 3 ) sol gel to produce fibers with 500-1000 nm diameters and subsequently calcinated to acquire perovskite BaTiO 3 . An active nanocomposite paint was formed using the resulting piezoelectric wires and was compared to the same paint with piezoelectric nanoparticles. The results show that the piezoceramic wires produce 0-3 nanocomposites with as high as 300% increase in electromechanical coupling

  18. Raman, dielectric and variable range hopping nature of Gd2O3-doped K0.5N0.5NbO3 piezoelectric ceramics

    Directory of Open Access Journals (Sweden)

    Mahesh Peddigari

    2015-10-01

    Full Text Available (K0.5Na0.5NbO3 (KNN + x wt% Gd2O3 (x = 0 -1.5 ceramics have been prepared by conventional solid state reaction method. The effect of Gd2O3 on the structural, microstructural and dielectric properties of KNN ceramics were studied systematically. The effect of Gd2O3 on phase transformation from orthorhombic to psuedocubic structure is explained interms of changes in the internal vibration modes of NbO6 octahedra. The Raman intensity of the stretching mode v1 enhanced and shifted toward higher wavenumber with Gd2O3 concentration, which is attributed to the increase in polarizability and change in the O-Nb-O bond angles. Microstructural analysis revealed that the grain size of the KNN ceramics decreases from 2.26 ± 1.07 μm to 0.35 ± 0.13 μm and becomes homogenous with an increase in Gd2O3 concentration. The frequency dependent dielectric spectra are analyzed by using Havriliak-Negami function. The fitted symmetry parameter and relaxation time (τ are found to be 0.914 and 8.78 × 10−10 ± 5.5 × 10−11 s, respectively for the sample doped with x = 1.0. The addition of Gd2O3 to the KNN shifted the polymorphic phase transition orthorhombic to tetragonal transition temperature (TO-T from 199oC to 85oC with enhanced dielectric permittivity (ε′ = 1139 at 1 MHz. The sample with x = 1.0, shown a high dielectric permittivity (ε′ = 879 and low dielectric loss (<5% in the broad temperature range (-140oC – 150oC with the Curie temperature 307 oC can have the potential for high temperature piezoelectric and tunable RF circuit applications. The temperature dependent AC-conductivity follows the variable range hopping conduction mechanism by obtaining the slope -0.25 from the ln[ln(ρac] versus ln(T graph in the temperature range of 133 K-308 K. The effect of Gd2O3 on the Mott’s parameters such as density of states (N(EF, hopping length (RH, and hopping energy (WH have been discussed.

  19. Enhanced green upconversion by controlled ceramization of Er3+–Yb3+ co-doped sodium niobium tellurite glass–ceramics for low temperature sensors

    International Nuclear Information System (INIS)

    Suresh Kumar, J.; Pavani, K.; Graça, M.P.F.; Soares, M.J.

    2014-01-01

    Highlights: • Upconversion luminescence improved in glass–ceramics compared to host glass. • Judd–Ofelt and radiative parameters calculated. • NIR decay curve results concur the results of improved luminescence. • Temperature dependent upconversion support the use of materials for sensors. - Abstract: Tellurite based glasses are well-known for their upconversion properties besides having a disadvantage of low mechanical strength dragging them away from practical applications. The present work deals with preparation of sodium niobium tellurite (SNT) glasses using melt quenching method, in which small quantities of boron and silicon in the form of oxides are added to improve their mechanical properties. Controlled heat treatment is performed to ceramize the prepared glasses based on the thermal data given by DTA. XRD and SEM profiles of the glass–ceramics which confirmed the formation of crystalline monoclinic Sodium Tellurium Niobium Oxide (Na 1.4 Nb 3 Te 4.9 O 18 ) phase (JCPDS card No. 04–011-7556). Upconversion measurements in the visible region were made for the prepared Er 3+ –Yb 3+ co-doped glasses and glass–ceramics with 980 nm laser excitation varying the laser power and concentration of Er 3+ ions. Results showed that the upconversion luminescence intensity was enhanced by ten times in SNT glass–ceramics compared to that in the SNT glasses. Decay curves give evidence of high performance of glass–ceramics compared to glasses due to ceramization and structural changes. Temperature dependent visible upconversion was performed to test the ability of efficient SNT glass–ceramic at low temperatures and variation of upconversion intensities was studied

  20. Processing and optimization of functional ceramic coatings and inorganic nanomaterials

    Science.gov (United States)

    Nyutu, Edward Kennedy G.

    effects on the synthesis of nanocrystalline tetragonal barium titanate. The effects of microwave frequency (fixed and variable), microwave bandwidths sweep time, and aging time on the microstructure, particle sizes, phase purity, surface areas, and porosities of the as-prepared BaTiO3 were systematically investigated. The final part of the research involves a new rapid and facile synthetic route to prepare size-tunable, ultranarrow, high surface area OMS-2 nanomaterials via open-vessel microwave-assisted refluxing preparations without employing templates or surfactants. The particle size control is achieved by varying the concentration or type of non-aqueous co-solvent. The structural, textural, and catalytic application properties of the prepared nanomaterials are investigated.

  1. Utilization of niobium pentoxide as additive for reducing the ''in situ'' reaction temperature of ceramic composites in the system mullite-zirconia

    International Nuclear Information System (INIS)

    Melo, F.C.L. de; Cairo, C.A.A.; Piorino Neto, F.; Cunha, P.A.; Devezas, T.C.

    1988-01-01

    Ceramics Composites of the system mullite-zirconia were produced trough reaction sintering, following the equation: 2ZrSiO 4 +3Al 2 O 3 +x(Al 2 O 3 +Nb 2 O 5 )--> 2ZrO 2 +Al 6 Si 2 O 13 +2xAlNbO 4 , with different x values (0.05,0.1 e 0.25), trying to investigate the role of niobia as sintering aid. Through x-ray diffraction was evaluated the fraction of zirconia tetragonal phase retained in the ceramic matrix, and the produced composites were caracterized as to the apparent porosity and density, sintering shrinkage and rupture strenght. The reaction sintering temperature was reduced from 1600 0 C (x=0) to 1400 0 C (with x=0.1). (author) [pt

  2. Relationship between ferroelectric properties and local structure of Pb{sub 1−x}Ba{sub x}Zr{sub 0.40}Ti{sub 0.60}O{sub 3} ceramic materials studied by X-ray absorption and Raman spectroscopies

    Energy Technology Data Exchange (ETDEWEB)

    Mesquita, Alexandre, E-mail: mesquita@rc.unesp.br [Instituto de Geociências e Ciências Exatas, UNESP – Univ Estadual Paulista, Departamento de Física, Av. 24-a, 1515, Rio Claro, SP 13506-900 (Brazil); Institut de Chimie et des Materiaux Paris Est, CNRS and Université Paris Est Créteil, 2 Rue Henri Dunant, 94320 Thiais (France); Instituto de Física de São Carlos, Universidade de São Paulo, Av. Trabalhador São-Carlense, 400, São Carlos, SP (Brazil); Michalowicz, Alain, E-mail: michalov@u-pec.fr [Institut de Chimie et des Materiaux Paris Est, CNRS and Université Paris Est Créteil, 2 Rue Henri Dunant, 94320 Thiais (France); Moscovici, Jacques, E-mail: moscovic@u-pec.fr [Institut de Chimie et des Materiaux Paris Est, CNRS and Université Paris Est Créteil, 2 Rue Henri Dunant, 94320 Thiais (France); Pizani, Paulo Sergio, E-mail: pizani@df.ufscar.br [Departamento de Física, Universidade Federal de São Carlos, Rodovia Washington Luís, s/n, São Carlos, SP, 13565-905 (Brazil); Mastelaro, Valmor Roberto, E-mail: valmor@ifsc.usp.br [Instituto de Física de São Carlos, Universidade de São Paulo, Av. Trabalhador São-Carlense, 400, São Carlos, SP (Brazil)

    2016-08-15

    This paper reports on the structural characterization of Pb{sub 1−x}Ba{sub x}Zr{sub 0.40}Ti{sub 0.60}O{sub 3} (PBZT) ferroelectric ceramic compositions prepared by the conventional solid state reaction method. X-ray absorption spectroscopy (XAS) and Raman spectroscopy were used in the probing of the local structure of PBZT samples that exhibit a normal or relaxor ferroelectric behavior. They showed a considerable local disorder around Zr and Pb atoms in the samples of tetragonal or cubic long-range order symmetry. The intensity of the E(TO{sub 3}) mode in the Raman spectra of PBZT relaxor samples remains constant at temperatures lower than T{sub m}, which has proven the stabilization of the correlation process between nanodomains. - Graphical abstract: X-ray absorption measurements showed considerable local disorder around Zr and Pb atoms in the samples of tetragonal or cubic long-range order symmetry. The intensity of the E(TO{sub 3}) mode in the Raman spectra of PBZT relaxor samples remains constant at temperatures lower than T{sub m}, which has proven the stabilization of the correlation process between nanodomains. Display Omitted - Highlights: • Structural characterization of Pb{sub 1−x}Ba{sub x}Zr{sub 0.40}Ti{sub 0.60}O{sub 3} (PBZT) ferroelectric ceramic. • X-ray absorption and Raman spectroscopies were used to probe the structure of PBZT. • Dissymmetry of Zr and Pb sites was observed in samples long-range cubic symmetry. • Local disorder in all PBZT samples through the observation of Raman active modes.

  3. Enhanced Luminescent Properties in Tm3+/Dy3+ Co-doped Transparent Phosphate Glass Ceramic

    OpenAIRE

    Yao L. Q.; Chen G. H.; Zhong H. J.; Cui S. C.; Li F.; Gan J.Y.

    2016-01-01

    Novel Tm3+/Dy3+ co-doped phosphate glass and glass ceramic samples for white light emitting diodes were prepared by melt quenching method. Under 353 nm excitation, the colors of the luminescence of the glass and glass ceramic samples are white. The CIE chromaticity coordinates (0.338, 0.328) of the emission from the glass ceramic is close to the standard white-light illumination (0.333, 0.333). Compared to the glass, the fluorescence intensity in the glass ceramic is greatly enhanced.

  4. Experimental study on the penetration effect of ceramics composite projectile on ceramic / A3 steel compound targets

    Directory of Open Access Journals (Sweden)

    Di-qi Hu

    2017-08-01

    Full Text Available In order to improve the penetration of projectiles into ceramic composite armors, the nose of 30 mm standard projectile was replaced by a toughened ceramic nose, and the performance of ceramic-nose projectiles penetrating into ceramic/A3 steel composite targets has been experimentally researched. According to impact dynamics theory,, the performances of 30 mm ceramic-nose projectile and 30 mm standard projectile penetrating into the ceramic/A3 steel composite targets were analyzed and compared using DOP method, especially focusing on the effects made by different nose structures and materials. The aperture and depth of perforation of projectile into the armor plates as well as the residual mass of bullet core under the same conditions were comparatively analyzed. A numerical simulation was built and computed by ANSYS/LS-DYNA. Based on the simulated results, the penetration performance was further analyzed in terms of the residual mass of bullet core. The results show that the ceramic nose has a great effect on the protection of bullet core.

  5. Extended phase homogeneity and electrical properties of barium calcium titanate prepared by the wet chemical methods

    International Nuclear Information System (INIS)

    Jayanthi, S.; Kutty, T.R.N.

    2004-01-01

    Ca-substituted BaTiO 3 with extended homogeneity range upto ∼50 mol% CaTiO 3 have been prepared by three different chemical routes namely carbonate-oxalate (COBCT), gel-carbonate (GCBCT), and gel-to-crystallite conversion (GHBCT) followed by heat treatment above 1150 deg. C. X-ray powder diffraction (XRD) data show continuous decrease in the tetragonal unit cell parameters as well as c 0 /a 0 ratio with CaTiO 3 content, which are in accordance with the substitution of smaller sized Ca 2+ ions at the barium sites. The microstructure as well as the dielectric properties are greatly influenced by the cationic ratio, α=(Ba+Ca)/Ti. The grain size decreases with CaTiO 3 content for the stoichiometric samples (α=1), whereas ultrafine microstructure is observed in the case of off-stoichiometric samples (α>1) for the whole compositional range of CaTiO 3 concentrations. Sharper ε r -T characteristics at lower calcium content and broader ε r -T with decreased ε max , in the higher calcium range are observed in the case of α=1. Whereas nanometer grained ceramics exhibiting diffuse ε r -T characteristics are obtained in the case of α>1. The positive temperature coefficient of resistivity (PTCR) is realized for barium calcium titanate ceramics having 0.3 at.% Sb as the donor dopant for higher CaTiO 3 (typically 30 mol%) containing samples (α=1), indicating that Ca 2+ ions do not behave as acceptors if they were to substitute at the Ti 4+ sites. Whereas the off-stoichiometric (α>1) ceramics retained high resistivity, indicative of the Ti-site occupancy for Ca 2+ in fine grain ceramics

  6. Lead-Free KNbO3:xZnO Composite Ceramics.

    Science.gov (United States)

    Lv, Xiang; Li, Zhuoyun; Wu, Jiagang; Xiao, Dingquan; Zhu, Jianguo

    2016-11-09

    It is a tough issue to develop dense and water resistant KNbO 3 ceramics due to high evaporation and hygroscopicity of K 2 O. Here, KNbO 3 :xZnO composite ceramics were used to successfully solve this problem, where ZnO particles were randomly distributed into a KNbO 3 matrix. The addition of ZnO hardly affects the phase structure of KNbO 3 , and moreover, the enhancement of electrical properties, thermal stability, and aging characteristics was observed in KNbO 3 :xZnO composite ceramics. The composites possessed the maximum d 33 of 120 ± 5 pC/N, which is superior to that of pure KNbO 3 (d 33 = 80 pC/N). More importantly, a strong water resistance and an aging-free characteristic were observed in KNbO 3 :0.4ZnO. This is the first time for KNbO 3 ceramics to simultaneously improve electrical properties and resolve the water-absorbing properties. We believe that these composite ceramics are promising for practical applications.

  7. Contributions to the R-curve behaviour of ceramic materials

    International Nuclear Information System (INIS)

    Fett, T.

    1994-12-01

    Several ceramic materials show an increase in crack growth resistance with increasing crack extension. Especially, in case of coarse-grained alumina this ''R-curve effect'' is caused by crack-face interactions in the wake of the advancing crack. Similar effects occur for whisker reinforced ceramics. Due to the crack-face interactions so-called ''bridging stresses'' are generated which transfer forces between the two crack surfaces. A second reason for an increase of crack-growth resistance are stress-induced phase transformations in zirconia ceramics with the tetragonal phase changing to the monoclinic phase. These transformations will affect the stress field in the surroundings of crack tips. The transformation generates a crack-tip transformation zone and, due to the stress balance, also residual stresses in the whole crack region which result in a residual stress intensity factor. This additional stress intensity factor is also a reason for the R-curve behaviour. In this report both effects are outlined in detail. (orig.) [de

  8. Composition dependence of electric-field-induced structure of Bi{sub 1/2}(Na{sub 1−x}K{sub x}){sub 1/2}TiO{sub 3} lead-free piezoelectric ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Khansur, Neamul H. [School of Materials Science and Engineering, UNSW Australia, 2052 Sydney (Australia); Department of Materials Science, University of Erlangen-Nürnberg, Erlangen 91058 (Germany); Benton, Rachel [Department of Chemical and Biomolecular Engineering, North Carolina State University, North Carolina 27695 (United States); Dinh, Thi Hinh; Lee, Jae-Shin [School of Materials Science and Engineering, University of Ulsan, Ulsan 680-749 (Korea, Republic of); Jones, Jacob L. [Department of Materials Science and Engineering, North Carolina State University, North Carolina 27695 (United States); Daniels, John E. [School of Materials Science and Engineering, UNSW Australia, 2052 Sydney (Australia)

    2016-06-21

    Microscopic origins of the electric-field-induced strain for three compositions of Bi{sub 1/2}(Na{sub 1−x}K{sub x}){sub 1/2}TiO{sub 3} (x = 0.14, 0.18, and 0.22) (BNKT100x) ceramics have been compared using in situ high-energy (87.12 keV) X-ray diffraction. In the as-processed state, average crystallographic structure of BNKT14 and BNKT18 were found to be of rhombohedral symmetry, while BNKT22 was tetragonal. Diffraction data collected under electric field showed that both the BNKT14 and BNKT18 exhibit induced lattice strain and non-180° ferroelectric domain switching without any apparent phase transformation. The BNKT22 composition, in addition to the lattice strain and domain switching, showed an electric-field-induced transformation from a tetragonal to mixed tetragonal-rhombohedral state. Despite the difference in the origin of microscopic strain responses in these compositions, the measured macroscopic poling strains of 0.46% (BNKT14), 0.43% (BNKT18), and 0.44% (BNKT22) are similar. In addition, the application of a second poling field of opposite polarity to the first increased the magnitude of non-180° ferroelectric domain texture. This was suggested to be related to the existence of an asymmetric internal bias field.

  9. Nanocomposite multilayer capacitors comprising BaTiO3@TiO2 and poly(vinylidene fluoride-hexafluoropropylene for dielectric-based energy storage

    Directory of Open Access Journals (Sweden)

    Mojtaba Rahimabady

    2014-04-01

    Full Text Available Multilayer dielectric capacitors were fabricated from nanocomposite precursor comprised of BaTiO3@TiO2 core–shell nanosized particles and poly(vinylidene fluoride–hexafluoropropylene (P(VDF–HFP polymer matrix (20 vol%. The multilayer capacitors showed very high discharge speed and high discharged energy density of around 2.5 J/cm3 at its breakdown field (~ 166 MV/m. The energy density of the nanocomposite multilayer capacitors was substantially higher than the energy density of commercially used power capacitors. Low cost, flexible structure, high discharge rate and energy density suggest that the nanocomposite multilayer capacitors are promising for energy storage applications in many power devices and systems.

  10. Strong piezoelectricity in (1 - x)(K0.4Na0.6)(Nb0.96Sb0.04)O3-xBi0.5K0.5Zr1-ySnyO3 lead-free binary system: identification and role of multiphase coexistence.

    Science.gov (United States)

    Zheng, Ting; Wu, Jiagang; Xiao, Dingquan; Zhu, Jianguo; Wang, Xiangjian; Xin, Lipeng; Lou, Xiaojie

    2015-03-18

    Here we report a strong piezoelectric activity in (1 - x)(K0.4Na0.6)(Nb0.96Sb0.04)O3-xBi0.5K0.5Zr1-ySnyO3 lead-free ceramics by designing different phase boundaries. The phase boundaries concerning rhombohedral-orthorhombic-tetragonal (R-O-T) and rhombohedral-tetragonal (R-T) multiphase coexistence were attained by changing BKZS and Sn contents and then were identified by the X-ray diffraction patterns as well as temperature-dependent permittivity and ν1 Raman modes associated with BO6 perovskite octahedron. A high strain (strain = 0.21-0.28% and d33* = 707-880 pm/V) and a strong piezoelectric coefficient (d33 = 415-460 pC/N) were shown in the ceramics located at the multiphase coexistence region. The reported results of this work are superior to that (d33* ∼ 570 pm/V and d33 ∼ 416 pC/N) of the textured (K,Na,Li)(Nb,Ta,Sb)O3 ceramics [Nature 2004, 432, 84]. We believe that the material system of this work will become one of the most promising candidates for piezoelectric actuators.

  11. Synthesis of new perovskite and ''tetragonal bronze'' materials with thorium

    Energy Technology Data Exchange (ETDEWEB)

    Launay, S; Erb, A; Freundlich, W [Universite Paris-VI (France)

    1982-03-22

    Disclosure and crystal chemistry study of the solid solutions Th(NbO/sub 3/)/sub 4/, NaNbO/sub 3/ or AgNbO/sub 3/ with perovskite structure and Th(Nb, TaO/sub 3/)/sub 4/, K(Nb,Ta)O/sub 3/ with ''tetragonal tungstene bronze'' structure, ''Banana'' type.

  12. Synthesis and piezoelectric properties of (1 - x)Bi0.5(Na0.8K0.2)0.5TiO3-xSr2ZrTiO6 ceramics

    Science.gov (United States)

    Onishi, Ryo; Ogawa, Hirotaka; Iida, Daiki; Kan, Akinori

    2017-10-01

    The effects of Sr2ZrTiO6 (SZT) addition on the piezoelectric properties of (1 - x)Bi0.5(Na0.8K0.2)0.5TiO3 (BNKT)-xSZT ceramics were characterized in this study. The X-ray powder diffraction (XRPD) profiles and Raman spectra of the ceramics in the composition range of 0-0.02 implies the presence of morphotropic phase boundary (MPB) which consists of the rhombohedral and tetragonal phases. Moreover, the temperature dependence of dielectric loss indicated a presence of the ferroelectric-relaxor transition temperature (T F-R) of around 75 °C for x = 0.005 and the temperature dependence shifted to a lower temperature at x = 0.01. The temperature dependence of the P-E hysteresis loop of the ceramics at the compositions of x = 0.005-0.02 showed pinched hysteresis loops above T F-R. Regarding the piezoelectric constant (d 33), it was increased by SZT addition in the MPB region (x = 0-0.01) and the highest d 33 of 202 pC/N was obtained at the composition of x = 0.0025. The S-E unipolar loop was also evaluated, the strain of the ceramic increased up to x = 0.02; and the highest d33* = 436 pm/V was obtained at the composition of x = 0.02.

  13. Effects of grinding on properties of Mg-PSZ ceramics prepared by the surface enrichment of zirconia powders

    International Nuclear Information System (INIS)

    Deb, S.; Das, S.R.

    1995-01-01

    Commercial grade zirconia powders of mean particle size of 3.21 microns were super-ground in wet condition in alcoholic medium in a Planetary Ball-Mill for 12-hours using a zirconia pot as well as balls, in order to avoid contaminations from the grinding media. Sedigraph analysis data show the mean particle sizes within the range of 0.4 to 0.2 micron. The super-ground zirconia powders were then treated with appropriate acid and alkali solutions in order to enrich the surfaces of zirconia powders. The chemical analysis reports depict the enrichment phenomena of the processed zirconia powders. Magnesium oxide of different mole percentages (3 to 9%) have been incorporated to the above super-ground and enriched zirconia powder and green specimens were prepared by pressing with a suitable pressure of 200 MPa to yield the green compaction density of 3.06 gm/cm 3 . The compacted green specimens were sintered without pressure at 1,480 C in air followed by normal cooling. X-ray diffraction patterns of the above sintered and cooled specimens have confirmed the formation of Mg-PSZ ceramics with 40% tetragonal phase. The sintered PSZ-products have shown very good surface properties but at the cost of transverse rupture strength. The effects of grinding were observed on the above Mg-PSZ ceramics which exhibit very little change in the tetragonal phase even after 30-minutes of grinding with a 60-mesh diamond wheel at a normal pressure of 4 kg/cm 2

  14. Joining Dental Ceramic Layers With Glass

    Science.gov (United States)

    Saied, MA; Lloyd, IK; Haller, WK; Lawn, BR

    2011-01-01

    Objective Test the hypothesis that glass-bonding of free-form veneer and core ceramic layers can produce robust interfaces, chemically durable and aesthetic in appearance and, above all, resistant to delamination. Methods Layers of independently produced porcelains (NobelRondo™ Press porcelain, Nobel BioCare AB and Sagkura Interaction porcelain, Elephant Dental) and matching alumina or zirconia core ceramics (Procera alumina, Nobel BioCare AB, BioZyram yttria stabilized tetragonal zirconia polycrystal, Cyrtina Dental) were joined with designed glasses, tailored to match thermal expansion coefficients of the components and free of toxic elements. Scanning electron microprobe analysis was used to characterize the chemistry of the joined interfaces, specifically to confirm interdiffusion of ions. Vickers indentations were used to drive controlled corner cracks into the glass interlayers to evaluate the toughness of the interfaces. Results The glass-bonded interfaces were found to have robust integrity relative to interfaces fused without glass, or those fused with a resin-based adhesive. Significance The structural integrity of the interfaces between porcelain veneers and alumina or zirconia cores is a critical factor in the longevity of all-ceramic dental crowns and fixed dental prostheses. PMID:21802131

  15. Tetragonal and collapsed-tetragonal phases of CaFe2As2 : A view from angle-resolved photoemission and dynamical mean-field theory

    Science.gov (United States)

    van Roekeghem, Ambroise; Richard, Pierre; Shi, Xun; Wu, Shangfei; Zeng, Lingkun; Saparov, Bayrammurad; Ohtsubo, Yoshiyuki; Qian, Tian; Sefat, Athena S.; Biermann, Silke; Ding, Hong

    2016-06-01

    We present a study of the tetragonal to collapsed-tetragonal transition of CaFe2As2 using angle-resolved photoemission spectroscopy and dynamical mean field theory-based electronic structure calculations. We observe that the collapsed-tetragonal phase exhibits reduced correlations and a higher coherence temperature due to the stronger Fe-As hybridization. Furthermore, a comparison of measured photoemission spectra and theoretical spectral functions shows that momentum-dependent corrections to the density functional band structure are essential for the description of low-energy quasiparticle dispersions. We introduce those using the recently proposed combined "screened exchange + dynamical mean field theory" scheme.

  16. Interface Control of Ferroelectricity in an SrRuO3 /BaTiO3 /SrRuO3 Capacitor and its Critical Thickness.

    Science.gov (United States)

    Shin, Yeong Jae; Kim, Yoonkoo; Kang, Sung-Jin; Nahm, Ho-Hyun; Murugavel, Pattukkannu; Kim, Jeong Rae; Cho, Myung Rae; Wang, Lingfei; Yang, Sang Mo; Yoon, Jong-Gul; Chung, Jin-Seok; Kim, Miyoung; Zhou, Hua; Chang, Seo Hyoung; Noh, Tae Won

    2017-05-01

    The atomic-scale synthesis of artificial oxide heterostructures offers new opportunities to create novel states that do not occur in nature. The main challenge related to synthesizing these structures is obtaining atomically sharp interfaces with designed termination sequences. In this study, it is demonstrated that the oxygen pressure (PO2) during growth plays an important role in controlling the interfacial terminations of SrRuO 3 /BaTiO 3 /SrRuO 3 (SRO/BTO/SRO) ferroelectric (FE) capacitors. The SRO/BTO/SRO heterostructures are grown by a pulsed laser deposition method. The top SRO/BTO interface, grown at high PO2 (around 150 mTorr), usually exhibits a mixture of RuO 2 -BaO and SrO-TiO 2 terminations. By reducing PO2, the authors obtain atomically sharp SRO/BTO top interfaces with uniform SrO-TiO 2 termination. Using capacitor devices with symmetric and uniform interfacial termination, it is demonstrated for the first time that the FE critical thickness can reach the theoretical limit of 3.5 unit cells. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Ga2O3 doping and vacancy effect in KNN—LT lead-free piezoceramics

    Science.gov (United States)

    Tan, Zhi; Xing, Jie; Jiang, Laiming; Zhu, Jianguo; Wu, Bo

    2017-12-01

    Ga2O3 was doped into 0.95(K0.48Na0.52)NbO3—0.05LiTaO3 (KNN—LT) ceramics and its influences on the sintering behavior, phase structure and electrical properties of ceramics were studied. Firstly, SEM observation exhibits that more and more glass phase appears in ceramics with the gradual addition of Ga2O3, which determines the continuous decrease in sintering temperatures. And the addition of Ga2O3 is also found to increase the orthorhombic—tetragonal transition temperature ( T O—T) of system to a higher level. Secondly, both the density and the coercive field ( E C) of ceramics increase firstly and then decrease with increasing the Ga2O3 content, and the KNN—LT— xGa sample at x = 0.004 shows a pinched P— E hysteresis loop. Finally, the impedance characteristics of KNN—LT— xGa ceramics were investigated at different temperatures, revealing a typical vacancy related conduction mechanism. This work demonstrates that Ga2O3 is a good sintering aid for KNN-based ceramics, and the vacancy plays an important role in the sintering and electrical behaviors of ceramics.

  18. Cubic-tetragonal transformation and magnetic properties in copper ferrites with excess Fe/sub 2/O/sub 3/

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, M [Saitama Univ., Urawa (Japan)

    1977-01-01

    Measurements have been performed of cubic-tetragonal transition temperatures and magnetic properties on a set of those samples of the binary system CuO-Fe/sub 2/O/sub 3/ which contain Fe/sub 2/O/sub 3/ more than stoichiometric CuFe/sub 2/O/sub 4/. A marked magnetic hardening was observed on a sample of 40CuO.60Fe/sub 2/O/sub 3/ which has been verified, through the X-ray analyses and measurements of Moessbauer spectra, to result from the precipitation of ..cap alpha..-Fe/sub 2/O/sub 3/ taking place during annealing.

  19. Synthesis and characterization by diffraction of X-Ray and impedance spectroscopy the ferroelectric ceramic Ti0.4Fe0.3Nb0.3O2 (TFNO) with additions of Bi2O3

    International Nuclear Information System (INIS)

    Sousa, D.G.; Sales, A.J.M.; Carneiro, J.C.S.; Sancho, E.O.; Sombra, A.S.B.; Sales, J.C.

    2012-01-01

    The ceramic Ti 0.4F e 0.3 Nb 0. 3O 2 (TFNO), was synthesized through of the solid-state reaction technique. The oxides were mixed for 7h and calcined at 1075 deg C for 4h. Phase TFNO was confirmed via X-ray diffraction technique (XRD) and Rietveld refinement. Were made additions of 6% and 8% of Bi 2 O 3 to the calcined powder, that after the pressing and sintering at 1125 deg C, were submitted to analysis by XRD and impedance spectroscopy study. The X-ray diffraction technique confirm a rutile-type structure [TiO2 (tP6) ] to calcined powder and to presence of two phases, Ti0.4Fe0.3Nb0.3O2 (TFNO tetragonal-rutile P 42/m n m(136)) and Bi1.721Fe1.056Nb1.134O7 (BFNO cubic F d -3 m Z(227)), for samples sintered. The impedance spectroscopy reveal in 240°C, to TFNO with addition of 8% at 100 KHz, the following results: σ' = 0,0452(Ω.m) -1 ; ε r ' = 9613 e tgδ = 0,83556. (author)

  20. Evaluation of ceramic and polymeric materials for use in engineered barrier systems

    International Nuclear Information System (INIS)

    Fullam, H.T.; Skiens, W.E.

    1980-01-01

    Ceramic materials evaluated in the screening studies were Al 2 O 3 (99.8%), mullite, vitreous silica, BaTiO 3 , CaTiO 3 , CaZrO 3 , CaTiSiO 5 , TiO 2 , ZrSiO 4 , basalt, Pyroceram 9617, and Marcor code 9658 machinable glass ceramic. One grade of graphite (Toyotanso IB-11) was also evaluated. Demineralized water, a synthetic Hanford groundwater, and a synthetic NaCl brine solution were used in the screening tests. Demineralized water was used in all five of the leach tests, but the other solutions were only used in the static leach tests at 150 and 250 0 C. Based on the results obtained, graphite appears to be the most leach resistant of the materials tested with the two grades of alumina being the best of the ceramic materials. Titanium dioxide and ZrO 2 are the most leach resistant of the remaining materials. Candidate materials from all three general classes of polymers (thermoplastics, thermosets, and elastomers) were considered in the selection of materials. Selected groups of polymers were tested in the flowing autoclave at 150, 200, and 250 0 C with some polymers being further tested at the next higher temperature. Next, selected samples were exposed to gamma radiation. These samples were then submitted for tensile and elongation measurements. Selected samples which appeared promising from both autoclave and radiation testing were further evaluated by impact tests. The materials that appeared most promising after autoclave testing were the EPDM rubbers, polyphenylene sulfide, poly(ethylene-tetrafluoroethylene) copolymer, and polyfurfuryl alcohol. The radiation dose had little effect on polyfurfuryl alcohol and polyphenylene sulfide samples; very significant decreases in elongation were observed for the fluorocarbon copolymer and the EPDM rubbers. While the polyphenylene sulfide and polyfurfuryl alcohol showed little change in impact strength, poly(ethylene-tetrafluoroethylene) decreased in impact strength

  1. Effect of ZrO(2) additions on the crystallization, mechanical and biological properties of MgO-CaO-SiO(2)-P(2)O(5)-CaF(2) bioactive glass-ceramics.

    Science.gov (United States)

    Li, H C; Wang, D G; Meng, X G; Chen, C Z

    2014-06-01

    A series of ZrO(2) doped MgO-CaO-SiO(2)-P(2)O(5)-CaF(2) bioactive glass-ceramics were obtained by sintering method. The crystallization behavior, phase composition, morphology and structure of glass-ceramics were characterized. The bending strength, elastic modulus, fracture toughness, micro-hardness and thermal expansion coefficient (TEC) of glass-ceramics were investigated. The in vitro bioactivity and cytotoxicity tests were used to evaluate the bioactivity and biocompatibility of glass-ceramics. The sedimentation mechanism and growth process of apatites on sample surface were discussed. The results showed that the mainly crystalline phases of glass-ceramics were Ca(5)(PO4)3F (fluorapatite) and β-CaSiO(3). (β-wollastonite). m-ZrO(2) (monoclinic zirconia) declined the crystallization temperatures of glasses. t-ZrO(2) (tetragonal zirconia) increased the crystallization temperature of Ca(5)(PO4)(3)F and declined the crystallization temperature of β-CaSiO(3). t-ZrO(2) greatly increased the fracture toughness, bending strength and micro-hardness of glass-ceramics. The nanometer apatites were induced on the surface of glass-ceramic after soaking 28 days in SBF (simulated body fluid), indicating the glass-ceramic has good bioactivity. The in vitro cytotoxicity test demonstrated the glass-ceramic has no toxicity to cell. Copyright © 2014 Elsevier B.V. All rights reserved.

  2. Production of mullite-zirconia ceramics composites by 'In situ' reaction

    International Nuclear Information System (INIS)

    Melo, F.C.L. de; Cairo, C.A.A.; Piorino Neto, F.; Devezas, T.C.

    1987-01-01

    Mullita-zirconia ceramic composites were produced by 'In situ' reaction of alumina and brazilian zircon. The ideal curve of thermal treatment (reaction + sinterization) was determined for the obtention of composites of maximum mechanical resistence. The retained fraction of tetragonal fase was evaluated by X-ray difraction and correlated with the values of mechanical resistence obtained by different treatment curves. The performance of the developed composites under corrosion and thermal shock was evaluated by glass casting. (Author) [pt

  3. Effects of applied electric field during postannealing on the tunable properties of (Ba,Sr)TiO3 thin films

    International Nuclear Information System (INIS)

    Xia Yidong; Cheng Jinbo; Pan Bai; Wu Di; Meng Xiangkang; Liu Zhiguo

    2005-01-01

    The impact of postannealing in electric field on the structure, tunability, and dielectric behavior of rf magnetron sputtering derived (Ba,Sr)TiO 3 films has been studied. It has been demonstrated that postannealing in the proper electric field can increase the dielectric constant and the tunability remarkably and destroy the symmetry of capacitance-voltage characteristics of the films. The increased out-of-plane lattice constant and the appearance of the hysteresis loops in the electric-annealed films indicated the formation of small polar regions with tetragonal structure, which are responsible for the increased dielectric constant and tunability. It was proposed that the segregation of Ti 3+ ions caused by electric annealing could induce the formation of BaTiO 3 -like regions, which are ferroelectric at room temperature

  4. Effects of applied electric field during postannealing on the tunable properties of (Ba,Sr)TiO3 thin films

    Science.gov (United States)

    Xia, Yidong; Cheng, Jinbo; Pan, Bai; Wu, Di; Meng, Xiangkang; Liu, Zhiguo

    2005-08-01

    The impact of postannealing in electric field on the structure, tunability, and dielectric behavior of rf magnetron sputtering derived (Ba,Sr)TiO3 films has been studied. It has been demonstrated that postannealing in the proper electric field can increase the dielectric constant and the tunability remarkably and destroy the symmetry of capacitance-voltage characteristics of the films. The increased out-of-plane lattice constant and the appearance of the hysteresis loops in the electric-annealed films indicated the formation of small polar regions with tetragonal structure, which are responsible for the increased dielectric constant and tunability. It was proposed that the segregation of Ti3+ ions caused by electric annealing could induce the formation of BaTiO3-like regions, which are ferroelectric at room temperature.

  5. Barium zirconate-titanate/barium calcium-titanate ceramics via sol-gel process: novel high-energy-density capacitors

    International Nuclear Information System (INIS)

    Puli, Venkata Sreenivas; Kumar, Ashok; Scott, J F; Katiyar, Ram S; Chrisey, Douglas B; Tomozawa, M

    2011-01-01

    Lead-free barium zirconate-titanate/barium calcium-titanate, [(BaZr 0.2 Ti 0.80 )O 3 ] 1-x -[(Ba 0.70 Ca 0.30 )TiO 3 ] x (x = 0.10, 0.15, 0.20) (BZT-BCT) ceramics with high dielectric constant, low dielectric loss and moderate electric breakdown field were prepared by the sol-gel synthesis technique. X-ray diffraction patterns revealed tetragonal crystal structure and this was further confirmed by Raman spectra. Well-behaved ferroelectric hysteresis loops and moderate polarizations (spontaneous polarization, P s ∼ 3-6 μC cm -2 ) were obtained in these BZT-BCT ceramics. Frequency-dependent dielectric spectra confirmed that ferroelectric diffuse phase transition (DPT) exists near room temperature. Scanning electron microscope images revealed monolithic grain growth in samples sintered at 1280 deg. C. 1000/ε versus (T) plots revealed ferroelectric DPT behaviour with estimated γ values of ∼1.52, 1.51 and 1.88, respectively, for the studied BZT-BCT compositions. All three compositions showed packing-limited breakdown fields of ∼47-73 kV cm -1 with an energy density of 0.05-0.6 J cm -3 for thick ceramics (>1 mm). Therefore these compositions might be useful in Y5V-type capacitor applications.

  6. Tetragonal to orthorhombic transformation in Mg-PSZ

    International Nuclear Information System (INIS)

    Liu, Z.W.; Spargo, A.E.C.; Hannink, R.H.J.; Drennan, J.

    1997-01-01

    The phase transformation from tetragonal to orthorhombic in MgO-partially-stabilized zirconia has been investigated by using high resolution transmission electron microscopy (HRTEM). Evidences are given to show that orthorhombic ZrO 2 frequently observed in transmission electron microscopy (TEM) thin foil studies was induced by dimpling and polishing during the specimen preparation. It was also found that the orthorhombic to monoclinic transformation was less sensitive to stress that the tetragonal to monoclinic transformation. 20 refs., 1 tab., 8 figs

  7. Synthesis and Piezoelectric Properties of Li, Ca and Mn-codoped BaTiO3 by a Solvothermal Approach

    International Nuclear Information System (INIS)

    Kimura, T; Dong, Q; Yin, S; Sato, T; Hashimoto, T; Sasaki, A; Aisawa, S

    2013-01-01

    3 at.% Li-doped (Ba 1-x Ca x )(Ti 1-y Mn y )O 3 particles with the Ca 2+ mole fraction, x, of 0–0.09 and Mn mole fraction, y, of 0 and 0.0005 were synthesized by a solvothermal approach at 200°C. The products consisted of nanoparticles of 50–100 nm in diameter, and did not change very much depending on the amount of Li, Ca and Mn-codoping. The change in relative dielectric constant, Δε r , in around room temperature decreased by doping Ca 2+ , and the lowest Δε r (4.51%) could be realized at x value of 0.03. The mechanical quality factor, Q m , of 3 at.% Li-doped (Ba 0.97 Ca 0.03 )(Ti 0.9995 Mn 0.0005 )O 3 increased to 521, and Δε r decreased to 1.72%, while the piezoelectric constant, d 33 (234pC/N), and electromechanical coupling factor, k p (40.0%), did not change very much compared with 3 at.% Li-doped BaTiO 3

  8. Electrospinning of Ceramic Solid Electrolyte Nanowires for Lithium-Ion Batteries with Enhanced Ionic Conductivity

    Science.gov (United States)

    Yang, Ting

    Solid electrolytes have great potential to address the safety issues of Li-ion batteries, but better synthesis methods are still required for ceramics electrolytes such as lithium lanthanum titanate (LLTO) and lithium lanthanum zirconate (LLZO). Pellets made from ceramic nanopowders using conventional sintering can be porous due to the agglomeration of nanoparticles (NPs). Electrospinning is a simple and versatile technique for preparing oxide ceramic nanowires (NWs) and was used to prepare electrospun LLTO and LLZO NWs. Pellets prepared from the electrospun LLTO NWs had higher density, less void space, and higher Li+ conductivity compared to those comprised of LLTO prepared with conventional sol-gel methods, which demonstrated the potential that electrospinning can provide towards improving the properties of sol-gel derived ceramics. Cubic phase LLZO was stabilized at room temperature in the form of electrospun NWs without extrinsic dopants. Bulk LLZO with tetragonal structure was transformed to the cubic phase using particle size reduction via ball milling. Heating conditions that promoted particle coalescence and grain growth induced a transformation from the cubic to tetragonal phase in both types of nanostructured LLZO. Composite polymer solid electrolyte was fabricated using LLZO NWs as the filler and showed an improved ionic conductivity at room temperature. Nuclear magnetic resonance studies show that LLZO NWs partially modify the polymer matrix and create preferential pathways for Li+ conduction through the modified polymer regions. Doping did not have significant effect on improving the overall conductivity as the interfaces played a predominant role. By comparing fillers with different morphologies and intrinsic conductivities, it was found that both NW morphology and high intrinsic conductivity are desired.

  9. Enhanced green upconversion by controlled ceramization of Er{sup 3+}–Yb{sup 3+} co-doped sodium niobium tellurite glass–ceramics for low temperature sensors

    Energy Technology Data Exchange (ETDEWEB)

    Suresh Kumar, J., E-mail: suresh@ua.pt; Pavani, K.; Graça, M.P.F.; Soares, M.J.

    2014-12-25

    Highlights: • Upconversion luminescence improved in glass–ceramics compared to host glass. • Judd–Ofelt and radiative parameters calculated. • NIR decay curve results concur the results of improved luminescence. • Temperature dependent upconversion support the use of materials for sensors. - Abstract: Tellurite based glasses are well-known for their upconversion properties besides having a disadvantage of low mechanical strength dragging them away from practical applications. The present work deals with preparation of sodium niobium tellurite (SNT) glasses using melt quenching method, in which small quantities of boron and silicon in the form of oxides are added to improve their mechanical properties. Controlled heat treatment is performed to ceramize the prepared glasses based on the thermal data given by DTA. XRD and SEM profiles of the glass–ceramics which confirmed the formation of crystalline monoclinic Sodium Tellurium Niobium Oxide (Na{sub 1.4}Nb{sub 3}Te{sub 4.9}O{sub 18}) phase (JCPDS card No. 04–011-7556). Upconversion measurements in the visible region were made for the prepared Er{sup 3+}–Yb{sup 3+} co-doped glasses and glass–ceramics with 980 nm laser excitation varying the laser power and concentration of Er{sup 3+} ions. Results showed that the upconversion luminescence intensity was enhanced by ten times in SNT glass–ceramics compared to that in the SNT glasses. Decay curves give evidence of high performance of glass–ceramics compared to glasses due to ceramization and structural changes. Temperature dependent visible upconversion was performed to test the ability of efficient SNT glass–ceramic at low temperatures and variation of upconversion intensities was studied.

  10. Lead-free Ba0.8Ca0.2(ZrxTi1−x)O3 ceramics with large electrocaloric effect

    International Nuclear Information System (INIS)

    Asbani, B.; Dellis, J.-L.; Lahmar, A.; Gagou, Y.; El Marssi, M.; Courty, M.; Djellab, K.; Amjoud, M.; Mezzane, D.; Kutnjak, Z.

    2015-01-01

    The electrocaloric effect was investigated in lead-free Zr doped Ba 0.8 Ca 0.2 (Zr x Ti 1−x )O 3 (BCTZ) ceramics synthesized by a conventional sintering process. Room-temperature x-ray diffraction analysis showed that the tetragonal structure is obtained in BCTZ for x ≤ 0.08 and a pseudo cubic phase for x > 0.08. The dielectric spectroscopy and calorimetry revealed that the Curie temperature decreases as a consequence of Zr doping and that the BCTZ exhibits a first order ferroelectric phase transition. The electrocaloric effect was determined by the calculation of the electrocaloric change of temperature (ΔT) using the Maxwell relation based on the P–E hysteresis loops measured at different temperatures. A large electrocaloric responsivity ΔT/ΔE = 0.34 × 10 −6  Km/V was found for x = 0.04, which significantly exceeds of values found so far in other lead-free electrocaloric materials

  11. Upconversion studies of Er3+/Yb3+ doped SrO.TiO2 borosilicate glass ceramic system

    International Nuclear Information System (INIS)

    Maheshwari, Aditya; Om Prakash; Kumar, Devendra; Rai, S.B.

    2011-01-01

    Upconversion behaviour has been studied in various matrices and fine powders of SrTiO 3 by previous workers. In present work, Er 3+ /Yb 3+ were doped in appropriate ratio in SrO.TiO 2 borosilicate glass ceramic system to study the upconversion phenomenon. Dielectric properties of this class of glass ceramic system have been extensively investigated by Thakur et al. It has been observed that both upconversion efficiency and dielectric constant increases with transformation of glass into glass ceramic. Therefore, present investigation is based upon the study of optical as well as the electrical properties of same glass ceramic system. In order to prepare different crystalline matrices, two different Er 3+ /Yb 3+ :SrO.TiO 2 borosilicate glasses with same amount of Er 2 O 3 and Yb 2 O 3 were prepared by melt quench method. Glasses were transparent with light-wine colour. Glass ceramics were prepared from the glasses by heat treatment based on DTA (Differential thermal analysis) results. Glass ceramics were fully opaque with brownish-cream colour. Powder X-ray diffraction (XRD) patterns confirmed that two different crystalline matrices, Sr 3 Ti 2 O 7 , Ti 10 O 19 and SrTiO 3 , TiO 2 were present in two glass ceramic samples respectively. Luminescence properties of glass and glass ceramic samples with 976nm laser irradiation showed that the intensities of the green and red emission increased multiple times in glass ceramic than that of the glass. Possible mechanisms responsible for upconversion eg. Energy Transfer (ET) and Excited State Absorption (ESA), were studied through laser pumping power log dependence

  12. Electrically Induced Strain and Polarization Fatigue in Lead-Free Ceramics

    Science.gov (United States)

    Sommer, Daniel

    Piezoelectric ceramics have traditionally been used in commercial applications such as actuators and sensors. By far the most popular piezoceramics currently in use are Pb(Zr,Ti)O3-based (PZT) ceramics. PZT ceramics are able to produce large strain and polarization with the application of an electric field, and this is due to the Morphotropic phase boundary (MPB). A MPB is associated with the boundary between tetragonal and rhombohedral perovskite phases. A disadvantage of PZT ceramics is that they contain ? 60 wt. % of lead. Since lead is toxic, this poses an environmental and health hazard because lead is released into the surroundings during fabrication and disposal. Because of this, there is a push to discover lead-free alternatives that have comparable properties to PZT but none of the health risks. One possibility is Bi 1/2(Na0.8K0.2)1/2Ti0.985 Ta0.015O3 (BNKT-1.5Ta). In addition to comparable electrical properties, any lead-free alternatives must have decent fatigue resistance to be useful for applications. This thesis focuses on the fatigue properties of BNKT-1.5Ta. The composition demonstrates high strain for a given applied electric field. To determine the fatigue resistance of BNKT-1.5Ta, data was gathered on how strain and polarization changed over number of cycles. Furthermore, fatigue tests at different temperatures were performed to ascertain if temperature affected fatigue life. X-ray diffraction (XRD) patterns and dielectric measurements were also collected to further examine any change in crystal structure and relative permittivity, respectively, before and after cycling.

  13. Comparative study on cubic and tetragonal CexZr1-xO2 supported MoO3-catalysts for sulfur-resistant methanation

    Science.gov (United States)

    Liu, Zhaopeng; Xu, Yan; Cheng, Jiaming; Wang, Weihan; Wang, Baowei; Li, Zhenhua; Ma, Xinbin

    2018-03-01

    In this paper, two kinds of CexZr1-xO2 solid solution carriers with different Ce/Zr ratio were prepared by one-step co-precipitation method: the cubic Ce0.8Zr0.2O2 and the tetragonal Ce0.2Zr0.8O2 support. The MoO3/Ce0.8Zr0.2O2 and MoO3/Ce0.2Zr0.8O2 catalysts were prepared by incipient wetness impregnation method for comparative study on sulfur-resistant methanation reaction. The N2 adsorption/desorption, X-ray diffraction (XRD), Raman spectroscopy (RS), X-ray photoelectron (XPS), transmission electron microscopy (TEM), temperature-programmed red