Erosion and erosion-corrosion

International Nuclear Information System (INIS)

Isomoto, Yoshinori

2008-01-01

It is very difficult to interpret the technical term of erosion-corrosion' which is sometimes encountered in piping systems of power plants, because of complicated mechanisms and several confusing definitions of erosion-corrosion phenomena. 'FAC (flow accelerated corrosion)' is recently introduced as wall thinning of materials in power plant systems, as a representative of 'erosion-corrosion'. FAC is, however, not necessarily well understood and compared with erosion-corrosion. This paper describes firstly the origin, definition and fundamental understandings of erosion and erosion-corrosion, in order to reconsider and reconfirm the phenomena of erosion, erosion-corrosion and FAC. Next, typical mapping of erosion, corrosion, erosion-corrosion and FAC are introduced in flow velocity and environmental corrosiveness axes. The concept of damage rate in erosion-corrosion is finally discussed, connecting dissolution rate, mass transfer of metal ions in a metal oxide film and film growth. (author)

Short and long-term thermo-erosion of ice-rich permafrost coasts in the Laptev Sea region

Science.gov (United States)

Günther, F.; Overduin, P. P.; Sandakov, A. V.; Grosse, G.; Grigoriev, M. N.

2013-02-01

Permafrost coasts in the Arctic are susceptible to a variety of changing environmental factors all of which currently point to increasing coastal erosion rates and mass fluxes of sediment and carbon to the shallow arctic shelf seas. Rapid erosion along high yedoma coasts composed of Ice Complex permafrost deposits creates impressive coastal ice cliffs and inspired research for designing and implementing change detection studies for a long time, but continuous quantitative monitoring and a qualitative inventory of coastal thermo-erosion for large coastline segments is still lacking. Our goal is to use observations of thermo-erosion along the mainland coast of the Laptev Sea in eastern Siberia to understand how erosion rates depend on coastal geomorphology and the relative contributions of waterline and atmospheric drivers to coastal thermo-erosion over the past 4 decades and in the past few years. We compared multitemporal sets of orthorectified satellite imagery from 1965 to 2011 for three segments of coastline with a length of 73 to 95 km each and analyzed thermo-denudation (TD) along cliff top and thermo-abrasion (TA) along cliff bottom for two nested time periods: long-term rates (the past 39-43 yr) and short term rates (the past 1-3 yr). The Normalized Difference Thermo-erosion Index (NDTI) was used as a proxy that qualitatively describes the relative proportions of TD and TA. Mean annual erosion rates at all three sites were higher in recent years (-5.3 ± 1.31 m a-1) than over the long term mean (-2.2 ± 0.13 m a-1). The Mamontov Klyk coast exhibit primarily spatial variations of thermo-erosion, while intrasite-specific variations were strongest at the Buor Khaya coast, where slowest long-term rates around -0.5 ± 0.08 m a-1 were observed. The Oyogos Yar coast showed continuously rapid erosion up to -6.5 ± 0.19 m a-1. In general, variable characteristics of coastal thermo-erosion were observed not only between study sites and over time, but also within

Rate estimates for lateral bedrock erosion based on radiocarbon ages, Duck River, Tennessee

International Nuclear Information System (INIS)

Brakenridge, G.R.

1985-01-01

Rates of bedrock erosion in ingrown meandering rivers can be inferred from the location of buried relict flood-plain and river-bank surfaces, associated paleosols, and radiocarbon dates. Two independent methods are used to evaluate the long-term rates of limestone bedrock erosion by the Duck River. Radiocarbon dates on samples retrieved from buried Holocene flood-plain and bank surfaces indicate lateral migration of the river bank at average rates of 0.6-1.9 m/100 yr. Such rates agree with lateral bedrock cliff erosion rates of 0.5-1.4 m/100 yr, as determined from a comparison of late Pleistocene and modern bedrock cliff and terrace scarp positions. These results show that lateral bedrock erosion by this river could have occurred coevally with flood-plain and terrace formation and that the resulting evolution of valley meander bends carved into bedrock is similar in many respects to that of channel meanders cut into alluvium. 11 references, 5 figures

Short- and long-term thermo-erosion of ice-rich permafrost coasts in the Laptev Sea region

Science.gov (United States)

Günther, F.; Overduin, P. P.; Sandakov, A. V.; Grosse, G.; Grigoriev, M. N.

2013-06-01

Permafrost coasts in the Arctic are susceptible to a variety of changing environmental factors all of which currently point to increasing coastal erosion rates and mass fluxes of sediment and carbon to the shallow arctic shelf seas. Rapid erosion along high yedoma coasts composed of Ice Complex permafrost deposits creates impressive coastal ice cliffs and inspired research for designing and implementing change detection studies for a long time, but continuous quantitative monitoring and a qualitative inventory of coastal thermo-erosion for large coastline segments is still lacking. Our goal is to use observations of thermo-erosion along the mainland coast of the Laptev Sea, in eastern Siberia, to understand how it depends on coastal geomorphology and the relative contributions of water level and atmospheric drivers. We compared multi-temporal sets of orthorectified satellite imagery from 1965 to 2011 for three segments of coastline ranging in length from 73 to 95 km and analyzed thermo-denudation (TD) along the cliff top and thermo-abrasion (TA) along the cliff bottom for two nested time periods: long-term rates (the past 39-43 yr) and short-term rates (the past 1-4 yr). The Normalized Difference Thermo-erosion Index (NDTI) was used as a proxy to qualitatively describe the relative proportions of TD and TA. Mean annual erosion rates at all three sites were higher in recent years (-5.3 ± 1.3 m a-1) than over the long-term mean (-2.2 ± 0.1 m a-1). The Mamontov Klyk coast exhibits primarily spatial variations of thermo-erosion, while intrasite-specific variations caused by local relief were strongest at the Buor Khaya coast, where the slowest long-term rates of around -0.5 ± 0.1 m a-1 were observed. The Oyogos Yar coast showed continuously rapid erosion up to -6.5 ± 0.2 m a-1. In general, variable characteristics of coastal thermo-erosion were observed not only between study sites and over time, but also within single coastal transects along the cliff profile

Anthropogenic control on geomorphic process rates: can we slow down the erosion rates? (Geomorphology Outstanding Young Scientist Award & Penck Lecture)

Science.gov (United States)

Vanacker, V.

2012-04-01

The surface of the Earth is changing rapidly, largely in response to anthropogenic perturbation. Direct anthropogenic disturbance of natural environments may be much larger in many places than the (projected) indirect effects of climate change. There is now large evidence that humans have significantly altered geomorphic process rates, mainly through changes in vegetation composition, density and cover. While much attention has been given to the impact of vegetation degradation on geomorphic process rates, I suggest that the pathway of restoration is equally important to investigate. First, vegetation recovery after crop abandonment has a rapid and drastic impact on geomorphic process rates. Our data from degraded catchments in the tropical Andes show that erosion rates can be reduced by up to 100 times when increasing the protective vegetation cover. During vegetation restoration, the combined effects of the reduction in surface runoff, sediment production and hydrological connectivity are stronger than the individual effects together. Therefore, changes in erosion and sedimentation during restoration are not simply the reverse of those observed during degradation. Second, anthropogenic perturbation causes a profound but often temporary change in geomorphic process rates. Reconstruction of soil erosion rates in Spain shows us that modern erosion rates in well-vegetated areas are similar to long-term rates, despite evidence of strong pulses in historical erosion rates after vegetation clearance and agriculture. The soil vegetation system might be resilient to short pulses of accelerated erosion (and deposition), as there might exist a dynamic coupling between soil erosion and production also in degraded environments.

Soil Production and Erosion Rates and Processes in Mountainous Landscapes

Science.gov (United States)

Heimsath, A. M.; DiBiase, R. A.; Whipple, K. X.

2012-12-01

We focus here on high-relief, steeply sloped landscapes from the Nepal Himalaya to the San Gabriels of California that are typically thought to be at a critical threshold of soil cover. Observations reveal that, instead, there are significant areas mantled with soil that fit the conceptual framework of a physically mobile layer derived from the underlying parent material with some locally-derived organic content. The extent and persistence of such soils depends on the long-term balance between soil production and erosion despite the perceived discrepancy between high erosion and low soil production rates. We present cosmogenic Be-10-derived soil production and erosion rates that show that soil production increases with catchment-averaged erosion, suggesting a feedback that enhances soil-cover persistence, even in threshold landscapes. Soil production rates do decline systematically with increasing soil thickness, but hint at the potential for separate soil production functions for different erosional regimes. We also show that a process transistion to landslide-dominated erosion results in thinner, patchier soils and rockier topography, but find that there is no sudden transition to bedrock landscapes. Our landslide modeling is combined with a detailed quantification of bedrock exposure for these steep, mountainous landscapes. We also draw an important conclusion connecting the physical processes producing and transporting soil and the chemical processes weathering the parent material by measuring parent material strength across three different field settings. We observe that parent material strength increases with overlying soil thickness and, therefore, the weathered extent of the saprolite. Soil production rates, thus, decrease with increasing parent material competence. These observation highlight the importance of quantifying hillslope hydrologic processes where such multi-facted measurements are made.

Sand mining impacts on long-term dune erosion in southern Monterey Bay

Science.gov (United States)

Thornton, E.B.; Sallenger, Abby; Sesto, Juan Conforto; Egley, L.; McGee, Timothy; Parsons, Rost

2006-01-01

Southern Monterey Bay was the most intensively mined shoreline (with sand removed directly from the surf zone) in the U.S. during the period from 1906 until 1990, when the mines were closed following hypotheses that the mining caused coastal erosion. It is estimated that the yearly averaged amount of mined sand between 1940 and 1984 was 128,000 m3/yr, which is approximately 50% of the yearly average dune volume loss during this period. To assess the impact of sand mining, erosion rates along an 18 km range of shoreline during the times of intensive sand mining (1940–1990) are compared with the rates after sand mining ceased (1990–2004). Most of the shoreline is composed of unconsolidated sand with extensive sand dunes rising up to a height of 46 m, vulnerable to the erosive forces of storm waves. Erosion is defined here as a recession of the top edge of the dune. Recession was determined using stereo-photogrammetry, and LIDAR and GPS surveys. Long-term erosion rates vary from about 0.5 m/yr at Monterey to 1.5 m/yr in the middle of the range, and then decrease northward. Erosion events are episodic and occur when storm waves and high tides coincide, allowing swash to undercut the dune and resulting in permanent recession. Erosion appears to be correlated with the occurrence of El Niños. The calculated volume loss of the dune in southern Monterey Bay during the 1997–98 El Niño winter was 1,820,000 m3, which is almost seven times the historical annual mean dune erosion of 270,000 m3/yr. The alongshore variation in recession rates appears to be a function of the alongshore gradient in mean wave energy and depletions by sand mining. After cessation of sand mining in 1990, the erosion rates decreased at locations in the southern end of the bay but have not significantly changed at other locations.

Modulation of the erosion rate of an uplifting landscape by long-term climate change: An experimental investigation

Science.gov (United States)

Moussirou, Bérangé; Bonnet, Stéphane

2018-02-01

Whether or not climatic variations play a major role in setting the erosion rate of continental landscapes is a key factor in demonstrating the influence of climate on the tectonic evolution of mountain belts and understanding how clastic deposits preserved in sedimentary basins may record climatic variations. Here, we investigate how a change in precipitation influences the erosional dynamics of laboratory-scale landscapes that evolved under a combination of uplift and rainfall forcings. We consider here the impact of a decrease in the precipitation rate of finite duration on the erosive response of a landscape forced by a constant uplift and initially at a steady state (SS1). We performed several experiments with the same amplitude but different durations of precipitation decrease (Tp). We observe that the decrease in precipitation induces a phase of surface uplift of landscapes to a new steady state condition (SS2); however, the details of the uplift histories (timing, rate) differ between the experiments according to Tp. We also observe a decrease in the erosion rate induced by the precipitation change; however, the timing and amplitude of this decrease vary according to Tp, defining a delayed and damped erosion signal. Our data show that the landscape response to precipitation change is dictated by a critical water-to-rock ratio (ratio of precipitation over uplift) that likely corresponds to a geomorphic threshold. Our study suggests that variations in precipitation that occur at a geological time scale (> 106 years) may have a weak impact on the erosion of landscapes and on the delivery of siliciclastic material to large rivers and sedimentary basins.

Experimental comparison of cavitation erosion rates of different steels used in hydraulic turbines

International Nuclear Information System (INIS)

Ton-That, L

2010-01-01

The prediction of cavitation erosion rates has an important role in order to evaluate the exact life of components in fluid machineries. Hydro-Quebec has studied this phenomenon for several years, in particular in hydraulic turbine runners, to try to understand the different degradation mechanisms related to this phenomenon. This paper presents part of this work. In this study, we carried out experimental erosion tests to compare different steels used in actual hydraulic turbine runners (carbon steels, austenitic and martensitic stainless steels) to high strength steels in terms of cavitation erosion resistance. The results for these different classes of steels are presented. The tests have been performed in a cavitating liquid jet apparatus according to the ASTM G134-95 standard to simulate the flow conditions. The mass loss has been followed during the exposure time. The maximum depth of erosion, the mean depth of erosion, and the mean depth erosion rate are determined. As a result we found that ASTM-A514 high strength steels present excellent cavitation erosion resistance properties. The cavitation eroded surface is followed by optical profilometry technique. Determination of mechanical properties and examinations of the eroded surfaces of the samples have also been carried out in order to identify the erosion mechanisms involved in the degradation of these kinds of materials.

Towards quantifying long-term erosion rates in the Campine Basin, NE Belgium

Science.gov (United States)

Beerten, Koen; Vanacker, Veerle

2016-04-01

The Campine Basin, NE Belgium, is situated between the uplifting Ardennes Massif and rapidly subsiding Roer Valley Graben. It contains a thick series of marine, estuarine and continental Neogene and Quaternary sediments, locally more than 300 m. As a result of relief inversion during the Quaternary, the Campine Plateau is nowadays a distinct morphological feature in this basin. Its surface elevation dips from 100 m in the south to 30 m in the north over a distance of about 60 km, which is the result of differential uplift. The Campine Plateau is covered by Early and Middle Pleistocene erosion-resistant fluvial sediments from the Rhine and Meuse and can thus be regarded as a fluvial terrace. The age of deposition and time of abandonment of the terrace have not yet been resolved by direct numerical dating. In this study, we apply the cosmogenic radionuclide (CRN) profiling technique that, in ideal circumstances, allows one to constrain the exposure age, burial age and amount of post-depositional erosion of the landform. Samples were taken from a 3.5 m deep cross-section in coarse river sands that were deposited by the river Rhine, and now situated at an altitude of about 50 m (a.s.l.). Nine of them were prepared for CRN measurements according to state-of-the-art techniques. The in-situ 10Be concentration of the samples was determined using accelerator mass spectrometry (ETH, Zurich). The in-situ 10Be concentrations are 1.5x10e5 atoms/g for the uppermost sample (at 0.3 m depth) and 0.9x10e5 at/g for the lowermost sample (at 3.1 m depth), yielding an estimated 0.6x10e5 at/g of radionuclide accumulation following sediment deposition. Using forward modelling, we solved for the exposure duration and erosion rate that best fit the measured in-situ 10Be depth profile data, nuclide inheritance and their associated analytical uncertainties. Model optimisation is here based on the sum of chi-squared between the measured and modelled 10Be concentrations. When taking previous

Coastal erosion and accretion rates in Greece

Science.gov (United States)

Foteinis, Spyros; Papadopoulos, Costas; Koutsogiannaki, Irini; Synolakis, Costas

2010-05-01

Erosion threatens many coastal regions of Greece. Anthropogenic changes of landforms such as coastal roads built on even narrow beaches, sand mining for construction, poor design of coastal structures that interfere with sediment, and dams without sediment bypasses have significantly reduced beach widths. We present erosion rates for different beaches, some of which are in sensitive ecosystems, otherwise "protected" by local and EU ordinances. By comparing inferences of beach widths in varying intervals from 1933 to 2006, we infer that the construction of dams in Acheloos river in western Greece, built in a faraonic attempt to partially divert its flows to eastern Greece, this is responsible for up to 20m/year erosion rates observed in certain locales in the Acheloos delta. More characteristic erosion rates in the region are ~ 2m/year. By contrast, there appears rapid accretion of up to 4m/year in the beaches around the Nestos delta in northern Greece (Papadopoulos, 2009). In beaches that are not near large river deltas, erosion rates range from 0.5m/year to 1m/year. While we have not done comprehensive comparisons among coastlines with different levels of coastal development, it does appear that rapid coastal development correlates well with erosion rates. The underlying problem is the complete lack of any semblance of coastal zone management in Greece and substandard design of coastal structures, which are often sited without any measurements of waves and currents offshore (Synolakis et al, 2008). Beach maintenance remains an exotic concept for most local authorities, who invariably prefer to build hard coastal structures to "protect" versus nourish, siting lack of experience with nourishment and "environmental" concerns. In certain cases, choices are dictated by costs, the larger the cost the easier the project gets approved by regulatory authorities, hence the preference for concrete or rubble structures. We conclude that, unless urgent salvage measures are

Testing the Control of Mineral Supply Rates on Chemical Erosion Rates in the Klamath Mountains

Science.gov (United States)

West, N.; Ferrier, K.

2016-12-01

The relationship between rates of chemical erosion and mineral supply is central to many problems in Earth science, including how tightly Earth's climate should be coupled to tectonics, how strongly nutrient supply to soils and streams depends on soil production, and how much lithology affects landscape evolution. Despite widespread interest in this relationship, there remains no consensus on how closely coupled chemical erosion rates should be to mineral supply rates. To address this, we have established a network of field sites in the Klamath Mountains along a latitudinal transect that spans an expected gradient in mineral supply rates associated with the geodynamic response to the migration of the Mendocino Triple Junction. Here, we present new measurements of regolith geochemistry and topographic analyses that will be compared with cosmogenic 10Be measurements to test hypotheses about supply-limited and kinetically-limited chemical erosion on granodioritic ridgetops. Previous studies in this area suggest a balance between rock uplift rates and basin wide erosion rates, implying the study ridgetops may have adjusted to an approximate steady state. Preliminary data are consistent with a decrease in chemical depletion fraction (CDF) with increasing ridgetop curvature. To the extent that ridgetop curvature reflects ridgetop erosion rates, this implies that chemical erosion rates at these sites are influenced by both mineral supply rates and dissolution kinetics.

Predicting the temporal relationship between soil cesium-137 and erosion rate

International Nuclear Information System (INIS)

Kachanoski, R.G.; De Jong, E.

1984-01-01

A model was developed that predicts the amount of 137 Cs remaining in soil as a function of time and erosion rate. The model accounts for atmospheric deposition, radioactive decay, tillage dilution, and erosion transport of 137 Cs, as well as seasonal differences in 137 Cs deposition and erosion rates. The model was used to estimate minimum resolution of erosion estimates based on detection limits and accuracy of 137 Cs measurement by gamma spectroscopy, as a function of time and erosion rate. The analysis showed that under Saskatchewan conditions, changes in 137 Cs at a given site can be used to estimate erosion rates between 0.5 and 10 kg m -2 yr -1 with reasonable precision, provided the sampling interval is at least 15 yr. The relationship of fraction of 137 Cs lost vs. erosion as predicted by the model was compared with other methods being used. The model was used to estimate erosion from selected Saskatchewan soils where 137 Cs levels were measured in 1966 and again in 1981. Erosion rates calculated with the model varied from 1 kg m -2 yr -1 for a sandy loam soil in continuous forage to 19 kg m -2 yr -1 for a similar soil in a crop-fallow rotation. Erosion estimates using the model were higher than those calculated by assuming that soil loss was directly proportional to 137 Cs loss, especially when 137 Cs loss was high

Soil Erosion and Agricultural Sustainability

Science.gov (United States)

Montgomery, D. R.

2009-04-01

Data drawn from a global compilation of studies support the long articulated contention that erosion rates from conventionally plowed agricultural fields greatly exceed rates of soil production, erosion under native vegetation, and long-term geological erosion. Whereas data compiled from around the world show that soil erosion under conventional agriculture exceeds both rates of soil production and geological erosion rates by up to several orders of magnitude, similar global distributions of soil production and geological erosion rates suggest an approximate balance. Net soil erosion rates in conventionally plowed fields on the order of 1 mm/yr can erode typical hillslope soil profiles over centuries to millennia, time-scales comparable to the longevity of major civilizations. Well-documented episodes of soil loss associated with agricultural activities date back to the introduction of erosive agricultural methods in regions around the world, and stratigraphic records of accelerated anthropogenic soil erosion have been recovered from lake, fluvial, and colluvial stratigraphy, as well as truncation of soil stratigraphy (such as truncated A horizons). A broad convergence in the results from studies based on various approaches employed to study ancient soil loss and rates of downstream sedimentation implies that widespread soil loss has accompanied human agricultural intensification in examples drawn from around the world. While a broad range of factors, including climate variability and society-specific social and economic contexts — such as wars or colonial relationships — all naturally influence the longevity of human societies, the ongoing loss of topsoil inferred from studies of soil erosion rates in conventional agricultural systems has obvious long-term implications for agricultural sustainability. Consequently, modern agriculture — and therefore global society — faces a fundamental question over the upcoming centuries. Can an agricultural system

Measurement of erosion rate by absorption spectroscopy in a Hall thruster

International Nuclear Information System (INIS)

Yamamoto, Naoji; Yokota, Shigeru; Matsui, Makoto; Komurasaki, Kimiya; Arakawa, Yoshihiro

2005-01-01

The erosion rate of a Hall thruster was estimated with the objective of building a real-time erosion rate monitoring system using a 1 kW class anode layer type Hall thruster. This system aids the understanding of the tradeoff between lifetime and performance. To estimate the flux of the sputtered wall material, the number density of the sputtered iron was measured by laser absorption spectroscopy using an absorption line from ground atomic iron at 371.9935 nm. An ultravioletAl x In y Ga (1-x-y) N diode laser was used as the probe. The estimated number density of iron was 1.1x10 16 m -3 , which is reasonable when compared with that measured by duration erosion tests. The relation between estimated erosion rate and magnetic flux density also agreed with that measured by duration erosion tests

Simulating CRN derived erosion rates in a transient Andean catchment using the TTLEM model

Science.gov (United States)

Campforts, Benjamin; Vanacker, Veerle; Herman, Frédéric; Schwanghart, Wolfgang; Tenrorio Poma, Gustavo; Govers, Gerard

2017-04-01

Assessing the impact of mountain building and erosion on the earth surface is key to reconstruct and predict terrestrial landscape evolution. Landscape evolution models (LEMs) are an essential tool in this research effort as they allow to integrate our growing understanding of physical processes governing erosion and transport of mass across the surface. The recent development of several LEMs opens up new areas of research in landscape evolution. Here, we want to seize this opportunity by answering a fundamental research question: does a model designed to simulate landscape evolution over geological timescales allows to simulate spatially varying erosion rates at a millennial timescale? We selected the highly transient Paute catchment in the Southeastern Ecuadorian Andes as a study area. We found that our model (TTLEM) is capable to better explain the spatial patterns of ca. 30 Cosmogenic Radio Nuclide (CRN) derived catchment wide erosion rates in comparison to a classical, statistical approach. Thus, the use of process-based landscape evolution models may not only be of great help to understand long-term landscape evolution but also in understanding spatial and temporal variations in sediment fluxes at the millennial time scale.

Reassessment of soil erosion on the Chinese loess plateau: were rates overestimated?

Science.gov (United States)

Zhao, Jianlin; Govers, Gerard

2014-05-01

Several studies have estimated regional soil erosion rates (rill and interrill erosion) on the Chinese loess plateau using an erosion model such as the RUSLE (e.g. Fu et al., 2011; Sun et al., 2013). However, the question may be asked whether such estimates are realistic: studies have shown that the use of models for large areas may lead to significant overestimations (Quinton et al., 2010). In this study, soil erosion rates on the Chinese loess plateau were reevaluated by using field measured soil erosion data from erosion plots (216 plots and 1380 plot years) in combination with a careful extrapolation procedure. Data analysis showed that the relationship between slope and erosion rate on arable land could be well described by erosion-slope relationships reported in the literature (Nearing, 1997). The increase of average erosion rate with slope length was clearly degressive, as could be expected from earlier research. However, for plots with permanent vegetation (grassland, shrub, forest) no relationship was found between erosion rates and slope gradient and/or slope length. This is important, as it implies that spatial variations of erosion on permanently vegetated areas cannot be modeled using topographical functions derived from observations on arable land. Application of relationships developed for arable land will lead to a significant overestimation of soil erosion rates. Based on our analysis we estimate the total soil erosion rate in the Chinese Loess plateau averages ca. 6.78 t ha-1 yr-1 for the whole loess plateau, resulting in a total sediment mobilisation of ca. 0.38 Gt yr-1. Erosion rates on arable land average ca. 15.10 t ha-1 yr-1. These estimates are 2 to 3 times lower than previously published estimates. The main reason why previous estimates are likely to be too high is that the values of (R)USLE parameters such as K, P and LS factor were overestimated. Overestimations of the K factor are due to the reliance of nomograph calculations, resulting

Comparing erosion rates in burnt forests and agricultural fields for a mountain catchment in NW Iberia

Science.gov (United States)

Nunes, João Pedro; Marisa Santos, Juliana; Bernard-Jannin, Léonard; Keizer, Jan Jacob

2013-04-01

the burnt area; in agricultural fields, rill formation occurred during the post-harvest period and before the full development of winter pasture. After this period, post-fire management operations (clear-cutting, deep plowing and replanting) disturbed the soil profiles and left little protective vegetation and litter cover. Relatively mild rainstorms provoked most of the erosion features in the burnt area, but none were observed in the agricultural fields which were fully covered by pasture at this time. The present results indicate that forest fires and especially post-fire management operations can lead to much higher erosion rates than agricultural practices. Different timings of soil losses throughout a year would be linked with different periods when soils are exposed: typically 2-3 years following fire and plowing/terracing as opposed to 2- 3 months following the harvest of annual crops (October-December). Assuming a recurrence period of forest fires of c. 25 years, burnt forests in the region would suffer similar long-term erosion rates as agricultural fields under comparable conditions, casting doubt on the role of forest plantations for soil protection in this region.

Long-term cliff retreat and erosion hotspots along the central shores of the Monterey Bay National Marine Sanctuary

Science.gov (United States)

Moore, Laura J.; Griggs, Gary B.

2002-01-01

Quantification of cliff retreat rates for the southern half of Santa Cruz County, CA, USA, located within the Monterey Bay National Marine Sanctuary, using the softcopy/geographic information system (GIS) methodology results in average cliff retreat rates of 7–15 cm/yr between 1953 and 1994. The coastal dunes at the southern end of Santa Cruz County migrate seaward and landward through time and display net accretion between 1953 and 1994, which is partially due to development. In addition, three critically eroding segments of coastline with high average erosion rates ranging from 20 to 63 cm/yr are identified as erosion ‘hotspots’. These locations include: Opal Cliffs, Depot Hill and Manresa. Although cliff retreat is episodic, spatially variable at the scale of meters, and the factors affecting cliff retreat vary along the Santa Cruz County coastline, there is a compensation between factors affecting retreat such that over the long-term the coastline maintains a relatively smooth configuration. The softcopy/GIS methodology significantly reduces errors inherent in the calculation of retreat rates in high-relief areas (e.g. erosion rates generated in this study are generally correct to within 10 cm) by removing errors due to relief displacement. Although the resulting root mean squared error for erosion rates is relatively small, simple projections of past erosion rates are inadequate to provide predictions of future cliff position. Improved predictions can be made for individual coastal segments by using a mean erosion rate and the standard deviation as guides to future cliff behavior in combination with an understanding of processes acting along the coastal segments in question. This methodology can be applied on any high-relief coast where retreat rates can be measured.

Testing the control of mineral supply rates on chemical erosion in the Klamath Mountains

Science.gov (United States)

West, N.; Ferrier, K.

2017-12-01

The relationship between rates of chemical erosion and mineral supply is central to many problems in Earth science, including the role of tectonics in the global carbon cycle, nutrient supply to soils and streams via soil production, and lithologic controls on landscape evolution. We aim to test the relationship between mineral supply rates and chemical erosion in the forested uplands of the Klamath mountains, along a latitudinal transect of granodioritic plutons that spans an expected gradient in mineral supply rates associated with the geodynamic response to the migration of the Mendocino Triple Junction. We present 10Be-derived erosion rates and Zr-derived chemical depletion factors, as well as bulk soil and rock geochemistry on 10 ridgetops along the transect to test hypotheses about supply-limited and kinetically-limited chemical erosion. Previous studies in this area, comparing basin-averaged erosion rates and modeled uplift rates, suggest this region may be adjusted to an approximate steady state. Our preliminary results suggest that chemical erosion at these sites is influenced by both mineral supply rates and dissolution kinetics.

Prediction of Soil Erosion Rates in Japan where Heavily Forested Landscape with Unstable Terrain

Science.gov (United States)

Nanko, K.; Oguro, M.; Miura, S.; Masaki, T.

2016-12-01

Soil is fundamental for plant growth, water conservation, and sustainable forest management. Multidisciplinary interest in the role of the soil in areas such as biodiversity, ecosystem services, land degradation, and water security has been growing (Miura et al., 2015). Forest is usually protective land use from soil erosion because vegetation buffers rainfall power and erosivity. However, some types of forest in Japan show high susceptibility to soil erosion due to little ground cover and steep slopes exceeding thirty degree, especially young Japanese cypress (Chamaecyparis obtusa) plantations (Miura et al., 2002). This is a critical issue for sustainable forest management because C. obtusaplantations account for 10% of the total forest coverage in Japan (Forestry Agency, 2009). Prediction of soil erosion rates on nationwide scale is necessary to make decision for future forest management plan. To predict and map soil erosion rates across Japan, we applied three soil erosion models, RUSLE (Revised Universal Soil Loss Equation, Wischmeier and Smith, 1978), PESERA (Pan-European Soil Erosion Risk Assessment, Kirkby et al., 2003), and RMMF (Revised Morgan-Morgan-Finney, Morgan, 2001). The grid scale is 1-km. RUSLE and PESERA are most widely used erosion models today. RMMF includes interactions between rainfall and vegetation, such as canopy interception and ratio of canopy drainage in throughfall. Evaporated rainwater by canopy interception, generally accounts for 15-20% in annual rainfall, does not contribute soil erosion. Whereas, larger raindrops generated by canopy drainage produced higher splash erosion rates than gross rainfall (Nanko et al., 2008). Therefore, rainfall redistribution process in canopy should be considered to predict soil erosion rates in forested landscape. We compared the results from three erosion models and analyze the importance of environmental factors for the prediction of soil erosion rates. This research was supported by the Environment

A multi-nuclide approach to quantify long-term erosion rates and exposure history through multiple glacial-interglacial cycles

DEFF Research Database (Denmark)

Strunk, Astrid; Larsen, Nicolaj Krog; Knudsen, Mads Faurschou

Cosmogenic nuclides are traditionally used to either determine the glaciation history or the denudation history of the most recent exposure period. A few studies use the cosmogenic nuclides to determine the cumulative exposure and burial durations of a sample. However, until now it has not been...... possible to resolve the complex pattern of exposure history under a fluctuating ice sheet. In this study, we quantify long-term erosion rates along with durations of multiple exposure periods in West Greenland by applying a novel Markov Chain Monte Carlo (MCMC) inversion approach to existing 10Be and 26Al....... The new MCMC approach allows us to constrain the most likely landscape history based on comparisons between simulated and measured cosmogenic nuclide concentrations. It is a fundamental assumption of the model that the exposure history at the site/location can be divided into two distinct regimes: i...

ESTIMATION OF THE WANDA GLACIER (SOUTH SHETLANDS SEDIMENT EROSION RATE USING NUMERICAL MODELLING

Directory of Open Access Journals (Sweden)

Kátia Kellem Rosa

2013-09-01

Full Text Available Glacial sediment yield results from glacial erosion and is influenced by several factors including glacial retreat rate, ice flow velocity and thermal regime. This paper estimates the contemporary subglacial erosion rate and sediment yield of Wanda Glacier (King George Island, South Shetlands. This work also examines basal sediment evacuation mechanisms by runoff and glacial erosion processes during the subglacial transport. This is small temperate glacier that has seen retreating for the last decades. In this work, we examine basal sediment evacuation mechanisms by runoff and analyze glacial erosion processes occurring during subglacial transport. The glacial erosion rate at Wanda Glacier, estimated using a numerical model that consider sediment evacuated to outlet streams, ice flow velocity, ice thickness and glacier area, is 1.1 ton m yr-1.

The influence of basal-ice debris on patterns and rates of glacial erosion

Science.gov (United States)

Ugelvig, Sofie V.; Egholm, David L.

2018-05-01

Glaciers have played a key role for shaping much of Earth's high topography during the cold periods of the Late Cenozoic. However, despite of their distinct influence on landscapes, the mechanisms of glacial erosion, and the properties that determine their rate of operation, are still poorly understood. Theoretical models of subglacial erosion generally highlight the influence of basal sliding in setting the pace of erosion, but they also point to a strong influence of other subglacial properties, such as effective bed pressure and basal-ice debris concentration. The latter properties are, however, not easily measured in existing glaciers, and hence their influence cannot readily be confirmed by observations. In order to better connect theoretical models for erosion to measurable properties in glaciers, we used computational landscape evolution experiments to study the expected influence of basal-ice debris concentration for subglacial abrasion at the scale of glaciers. The computational experiments couple the two erosion processes of quarrying and abrasion, and furthermore integrate the flow of ice and transport of debris within the ice, thus allowing for the study of dynamic feedbacks between subglacial erosion and systematic glacier-scale variations in basal-ice debris concentration. The experiments explored several physics-based models for glacial erosion, in combination with different models for basal sliding to elucidate the relationship between sliding speed, erosion rate and basal-ice debris concentration. The results demonstrate how differences in debris concentration can explain large variations in measured rates. The experiments also provide a simple explanation for the observed dependence of glacier-averaged rate of erosion on glacier size: that large glacier uplands feed more debris into their lower-elevation parts, thereby strengthening their erosive power.

Erosion rates and landscape evolution of the lowlands of the Upper Paraguay river basin (Brazil) from cosmogenic 10Be

Science.gov (United States)

Pupim, Fabiano do Nascimento; Bierman, Paul R.; Assine, Mario Luis; Rood, Dylan H.; Silva, Aguinaldo; Merino, Eder Renato

2015-04-01

slowly than associated residual hills, regional relief is decreasing over time and the landscape is not in steady state. The extremely slow erosion rates of the clastic-laterite are similar to the slowest outcrop erosion rates reported worldwide. These slow rates are due to the material's properties and resistance, being comprised of quartzite fragments cemented by an iron-rich crust, and reflecting long-term weathering with iron chemical precipitation and ferricrete formation, at least since the Middle Pleistocene. The lateritic caprock appears to be a key factor maintaining hilltop summits of the planation surface over long timescales.

Constraining Quaternary ice covers and erosion rates using cosmogenic 26Al/10Be nuclide concentrations

Science.gov (United States)

Knudsen, Mads Faurschou; Egholm, David Lundbek

2018-02-01

erosion rates, the model results may reconcile spatially varying 26Al/10Be data from bedrock surfaces preserved over multiple glacial cycles, suggesting that samples from the same high-elevation surface or neighbouring alpine summits may have experienced similar long-term burial under ice, but varying amounts of glacial erosion.

Modeling erosion of unsaturated compacted bentonite by groundwater flow; pinhole erosion test case

International Nuclear Information System (INIS)

Laurila, T.; Sane, P.; Olin, M.; Koskinen, K.

2012-01-01

swelling rate to erosion rate. Expressing eroded mass as a function of time as M(t) ∝ tβ. we note that for non-swelling material the wall shear -based erosion model gives β = 0,5. We find this limit in our model by suppressing swelling, and we observe that β increases when ratio of swelling to erosion increases, approaching values β ≅ 1 for strong swelling. It follows that the long term erosion of backfill and buffer materials are expected to differ, with erosion rates in the more compact buffer dropping slower. The result also suggests that the lower the initial erosion, the longer one can expect that rate to be maintained. We solve the model in cylindrically symmetric coordinates using COMSOL Multiphysics software, and fit parameters to match pinhole experiments on MX-80 bentonite with different salinities of the water inflow. Significant scatter within the experimental data makes it difficult to definitively validate models. Figure 1 shows erosion behavior in the model at the limit of vanishing swelling, and contrasts it to the highly-swelling case. Observations from the pinhole experiments, as well as from down-scaled piping erosion tests, show that erosion rates in buffer material don't drop significantly in time, suggesting a consistent with high swelling. In the larger piping erosion tests a seemingly steady state in the erosion rate is reached for an extended amount of time. The effects of scatter are reduced using statistical analysis of this state. An important experimental finding of unsaturated erosion is that larger salinities lead to larger erosion rates, in contrast to saturated erosion where the opposite has been observed. We expect this effect to be due to the processes of saturation, suction and permeability. Future work aims to model the dominant processes in this effect, as pertains to Posiva reference conditions for the Olkiluoto site, without going to the full complexity of (T)HM modeling, such as the Barcelona expansible model

In-situ real time measurements of net erosion rates of copper during hydrogen plasma exposure

Science.gov (United States)

Kesler, Leigh; Wright, Graham; Peterson, Ethan; Whyte, Dennis

2013-10-01

In order to properly understand the dynamics of net erosion/deposition in fusion reactors, such as tokamaks, a diagnostic measuring the real time rates of net erosion/deposition during plasma exposure is necessary. The DIONISOS experiment produces real time measurements of net erosion/deposition by using Rutherford backscattering spectroscopy (RBS) ion beam analysis simultaneously with plasma exposure from a helicon plasma source. This in-situ method improves on ex-situ weight loss measurements by allowing measurement of possible synergistic effects of high ion implantation rates and net erosion rate and by giving a real time response to changes in plasma parameters. Previous work has validated this new technique for measuring copper (Cu) erosion from helium (He) plasma ion bombardment. This technique is now extended to measure copper erosion due to deuterium and hydrogen plasma ion exposure. Targets used were a 1.5 μm Cu layer on an aluminum substrate. Cu layer thickness is tracked in real time using 1.2 MeV proton RBS. Measured erosion rates will be compared to results from literature and He erosion rates. Supported by US DoE award DE-SC00-02060.

Charge-exchange wall physical erosion rates for a proposed INTOR/FED limiter

International Nuclear Information System (INIS)

Heifetz, D.; Schmidt, J.; Ulrickson, M.; Post, D.

1983-01-01

We have analyzed power deposition and physical erosion rates on the first wall and limiter due to charge-exchange neutrals in a proposed pump limiter design for the INTOR/FED tokamak. Plasma conditions were modeled using the one-dimensional plasma transport code baldur. Neutral transport was modeled using a two-dimensional, multispecies Monte Carlo algorithm. No chemical erosion or wall redeposition processes were included. Two possible plasma discharges with different edge densities and temperatures were modeled, a regime with T/sub e/ approx.300 eV and napprox.5 x 10 12 cm - 3 , and a hotter, less dense edge regime produced with pellet fueling. We found that the erosion of the stainless steel vacuum vessel wall was highly localized in each case to the two points just beyond the limiter tips, and to the point directly across from the neutralizer plate, with peak erosion rates approx.2 cm/yr, assuming a 40% duty cycle. The erosion of a carbon limiter, neglecting redeposition and chemical erosion, varied in the two cases from 1.6--4 cm/yr, for the same duty cycle. The hotter, less dense discharge produced less sputtering. However achieving truly tolerable physical sputtering rates may require a very low edge temperature, plasma

The comparison of various approach to evaluation erosion risks and design control erosion measures

Science.gov (United States)

Kapicka, Jiri

2015-04-01

In the present is in the Czech Republic one methodology how to compute and compare erosion risks. This methodology contain also method to design erosion control measures. The base of this methodology is Universal Soil Loss Equation (USLE) and their result long-term average annual rate of erosion (G). This methodology is used for landscape planners. Data and statistics from database of erosion events in the Czech Republic shows that many troubles and damages are from local episodes of erosion events. An extent of these events and theirs impact are conditional to local precipitation events, current plant phase and soil conditions. These erosion events can do troubles and damages on agriculture land, municipally property and hydro components and even in a location is from point of view long-term average annual rate of erosion in good conditions. Other way how to compute and compare erosion risks is episodes approach. In this paper is presented the compare of various approach to compute erosion risks. The comparison was computed to locality from database of erosion events on agricultural land in the Czech Republic where have been records two erosion events. The study area is a simple agriculture land without any barriers that can have high influence to water flow and soil sediment transport. The computation of erosion risks (for all methodology) was based on laboratory analysis of soil samples which was sampled on study area. Results of the methodology USLE, MUSLE and results from mathematical model Erosion 3D have been compared. Variances of the results in space distribution of the places with highest soil erosion where compared and discussed. Other part presents variances of design control erosion measures where their design was done on based different methodology. The results shows variance of computed erosion risks which was done by different methodology. These variances can start discussion about different approach how compute and evaluate erosion risks in areas

Impact of glaciations on the long-term erosion in Southern Patagonian Andes

Science.gov (United States)

Simon-Labric, Thibaud; Herman, Frederic; Baumgartner, Lukas; Shuster, David L.; Braun, Jean; Reiners, Pete W.; Valla, Pierre G.; Leuthold, Julien

2014-05-01

The Southern Patagonian Andes are an ideal setting to study the impact of Late-Cenozoic climate cooling and onset of glaciations impact on the erosional history of mountain belts. The lack of tectonic activity during the last ~12 Myr makes the denudation history mainly controlled by surface processes, not by tectonics. Moreover, the glaciations history of Patagonia shows the best-preserved records within the southern hemisphere (with the exception of Antarctica). Indeed, the dry climate on the leeward side of Patagonia and the presence of lava flows interbedded with glacial deposits has allowed an exceptional preservation of late Cenozoic moraines with precise dating using K-Ar analyses on lava flow. The chronology of moraines reveals a long history covering all the Quaternary, Pliocene, and up to the Upper Miocene. The early growth of large glaciers flowing on eastern foothills started at ~7-6 Myr, while the maximum ice-sheet extent dates from approximately 1.1 Myr. In order to quantify the erosion history of the Southern Patagonian Andes and compare it to the glaciations sediment record, we collected samples along an age-elevation profile for low-temperature thermochronology in the eastern side of the mountain belt (Torres del Paine massif). The (U-Th)/He age-elevation relationship shows a clear convex shape providing an apparent long-term exhumation rate of ~0.2 km/Myr followed by an exhumation rate increase at ~6 Myr. Preliminary results of 4He/3He thermochronometry for a subset of samples complete the erosion history for the Plio-Pleistocene epoch. We used inverse procedure predicting 4He distributions within an apatite grain using a radiation-damage and annealing model to quantify He-diffusion kinetics in apatite. The model also allows quantifying the impact of potential U-Th zonation throughout each apatite crystal. Inversion results reveal a denudation history composed by a pulse of denudation at ~6 Ma, as suggested by the age-elevation relationship

ESTIMATION OF THE WANDA GLACIER (SOUTH SHETLANDS) SEDIMENT EROSION RATE USING NUMERICAL MODELLING

OpenAIRE

Kátia Kellem Rosa; Rosemary Vieira; Jefferson Cardia Simões

2013-01-01

Glacial sediment yield results from glacial erosion and is influenced by several factors including glacial retreat rate, ice flow velocity and thermal regime. This paper estimates the contemporary subglacial erosion rate and sediment yield of Wanda Glacier (King George Island, South Shetlands). This work also examines basal sediment evacuation mechanisms by runoff and glacial erosion processes during the subglacial transport. This is small temperate glacier that has seen retreating for the l...

A terminological matter: paragenesis, antigravitative erosion or antigravitational erosion ?

Directory of Open Access Journals (Sweden)

Pasini G.

2009-07-01

Full Text Available In the speleological literature three terms are utilized to designate the “ascending erosion”: paragenesis (= paragénésis, coined in1968, antigravitative erosion (= erosione antigravitativa, coined in 1966 and antigravitational erosion (wrong English translation ofthe Italian term erosione antigravitativa, utilized later on. The term paragenesis should be abandoned because of the priority of theterm erosione antigravitativa - on the ground of the “law of priority” – and because of its ambiguous etimology. On the other hand,the term antigravitational erosion should be forsaken in favour of the term antigravitative erosion, given the meaning that the termsgravitation and gravity have in Physics. Therefore, to designate the phenomenon of the “ascending erosion” there would be nothingleft but the term antigravitative erosion.The antigravitative erosion process and its recognizability are illustrated.Examples of caves with evident antigravitative erosion phenomena, developed in different karstifiable rocks and in several partsof the world, are given.It is recalled that the antigravitative erosion is a phenomenon well-known since 1942 and widely proven and supported, and that it isrelatively easy – in many cases - to recognize the antigravitative origin of karstic passages.It is stressed that the antigravitative erosion is an important phenomenon, exclusive of the karstic caves and unique in nature.

Tectonic controls of Holocene erosion in a glaciated orogen

OpenAIRE

Adams, Byron A.; Ehlers, Todd A.

2018-01-01

Recent work has highlighted a strong, worldwide, glacial impact of orogen erosion rates over the last 2 Ma. While it may be assumed that glaciers increased erosion rates when active, the degree to which past glaciations influence Holocene erosion rates through the adjustment of topography is not known. In this study, we investigate the influence of long-term tectonic and post-glacial topographic controls on erosion in a glaciated orogen, the Olympic Mountains, USA. We present 14 new 10Be and ...

Assessment of soil erosion and deposition rates in a Moroccan agricultural field using fallout 137Cs and 210Pbex

International Nuclear Information System (INIS)

Benmansour, M.; Mabit, L.; Nouira, A.; Moussadek, R.; Bouksirate, H.; Duchemin, M.; Benkdad, A.

2013-01-01

In Morocco land degradation – mainly caused by soil erosion – is one of the most serious agroenvironmental threats encountered. However, only limited data are available on the actual magnitude of soil erosion. The study site investigated was an agricultural field located in Marchouch (6°42′ W, 33° 47′ N) at 68 km south east from Rabat. This work demonstrates the potential of the combined use of 137 Cs, 210 Pb ex as radioisotopic soil tracers to estimate mid and long term erosion and deposition rates under Mediterranean agricultural areas. The net soil erosion rates obtained were comparable, 14.3 t ha −1 yr −1 and 12.1 ha −1 yr −1 for 137 Cs and 210 Pb ex respectively, resulting in a similar sediment delivery ratio of about 92%. Soil redistribution patterns of the study field were established using a simple spatialisation approach. The resulting maps generated by the use of both radionuclides were similar, indicating that the soil erosion processes has not changed significantly over the last 100 years. Over the previous 10 year period, the additional results provided by the test of the prediction model RUSLE 2 provided results of the same order of magnitude. Based on the 137 Cs dataset established, the contribution of the tillage erosion impact has been evaluated with the Mass Balance Model 3 and compared to the result obtained with the Mass Balance Model 2. The findings highlighted that water erosion is the leading process in this Moroccan cultivated field, tillage erosion under the experimental condition being the main translocation process within the site without a significant and major impact on the net erosion. - Highlights: ► Net erosion rates estimated by 137 Cs and 210 Pb ex techniques were found comparable. ► The water erosion is the leading process in this Moroccan cultivated field. ► Soil erosion process has not changed significantly over the last 100 years. ► The prediction model RUSLE 2 provided results of the same order of

Review of denudation processes and quantification of weathering and erosion rates at a 0.1 to 1 Ma time scale

Energy Technology Data Exchange (ETDEWEB)

Olvmo, Mats (Univ. of Goeteborg, Goeteborg (Sweden). Dept. of Earth Sciences)

2010-06-15

The Forsmark and Laxemar areas are quite similar from a geomorphological point of view. Both sites are situated within intact parts of the Sub-Cambrian Peneplain with extremely low relief. The peneplain is considered to be intact at both sites, i.e. the present relief is quite close to the original surface of this old denudation surface. The total amount of glacial erosion up to present is estimated to be relatively low at both sites (less than 10 m on average), but may have been quite important for stripping of old regolith, especially along fracture zones. This is most obvious in the vicinity of the Forsmark site where the dissected coastline 15 km south of the site is interpreted as a result of glacial erosion along old fracture zones. Therefore, from a strict glacial erosion perspective the Laxemar site is somewhat better than Forsmark. However, given the presented long-term denudation up to present, the expected amount of glacial erosion during a future glacial cycle, if similar to the last glacial cycle, is probably very limited for both sites, in the order of 2-5 m. Excluding glacial erosion, the long-term denudation rates of the two sites is fairly low as a consequence of the very low relief and the proximity to base level. The figures estimated for the long term denudation rates are in agreement with reports of denudation rates in shield areas and lie within the range 0 to 10 m/Ma for both sites. A scenario with a five-fold increase of relief that could be the effect of tectonic uplift, in a time perspective considerably longer than the coming 100,000 years, does not significantly change the picture. Even if the local relief is raised to above 100 m at both sites the estimated non-glacial denudation is very low. However, it should be noted that the effect of a relief change on the glacial system is not included in the calculations. Again, such a change on the pattern of glacial erosion would be more pronounced in the Forsmark area, since the coastline is

Review of denudation processes and quantification of weathering and erosion rates at a 0.1 to 1 Ma time scale

International Nuclear Information System (INIS)

Olvmo, Mats

2010-06-01

The Forsmark and Laxemar areas are quite similar from a geomorphological point of view. Both sites are situated within intact parts of the Sub-Cambrian Peneplain with extremely low relief. The peneplain is considered to be intact at both sites, i.e. the present relief is quite close to the original surface of this old denudation surface. The total amount of glacial erosion up to present is estimated to be relatively low at both sites (less than 10 m on average), but may have been quite important for stripping of old regolith, especially along fracture zones. This is most obvious in the vicinity of the Forsmark site where the dissected coastline 15 km south of the site is interpreted as a result of glacial erosion along old fracture zones. Therefore, from a strict glacial erosion perspective the Laxemar site is somewhat better than Forsmark. However, given the presented long-term denudation up to present, the expected amount of glacial erosion during a future glacial cycle, if similar to the last glacial cycle, is probably very limited for both sites, in the order of 2-5 m. Excluding glacial erosion, the long-term denudation rates of the two sites is fairly low as a consequence of the very low relief and the proximity to base level. The figures estimated for the long term denudation rates are in agreement with reports of denudation rates in shield areas and lie within the range 0 to 10 m/Ma for both sites. A scenario with a five-fold increase of relief that could be the effect of tectonic uplift, in a time perspective considerably longer than the coming 100,000 years, does not significantly change the picture. Even if the local relief is raised to above 100 m at both sites the estimated non-glacial denudation is very low. However, it should be noted that the effect of a relief change on the glacial system is not included in the calculations. Again, such a change on the pattern of glacial erosion would be more pronounced in the Forsmark area, since the coastline is

Fundamental study on cavitation erosion in liquid metal. Effect of liquid parameter on cavitation erosion in liquid metals (Joint research)

International Nuclear Information System (INIS)

Hattori, Shuji; Kurachi, Hiroaki; Inoue, Fumitaka; Watashi, Katsumi; Tsukimori, Kazuyuki; Yada, Hiroki; Hashimoto, Takashi

2009-02-01

Cavitation erosion, which possibly occurs on the surfaces of fluid machineries and components contacting flowing liquid and causes sponge-like damage on the material surface, is important problem, since it may become the cause of performance deduction, life shortening, noise, vibration of mechanical components and moreover failure of machine. Research on cavitation erosion in liquid metal is very important to confirm the safety of fast breeder reactor using sodium coolant and to avoid serious damage of the target vessel of spallation neutron source containing liquid-mercury. But the research on cavitation erosion in liquid metal has been hardly performed because of its specially in comparison with that in water. In this study, a cavitation erosion test apparatus was developed to carry out the erosion tests in low-temperature liquid metals. Cavitation erosion tests were carried out in liquid lead-bismuth alloy and in deionized water. We discuss the effect of liquid parameters and temperature effects on the erosion rate. We reach to the following conclusions. The erosion rate was evaluated in terms of a relative temperature which was defind as the percentage between freezing and boiling points. At 14degC relative temperature, the erosion rate is 10 times in lead-bismuth alloy, and 2 to 5 times in sodium, compared with that in deionized water. At 14degC relative temperature, the erosion rate can be evaluated in terms of the following parameter. 1 / (1/ρ L /C L +1/ρ S C S )√ρ L . Where ρ is the material density and c is the velocity of sound, L and S denote liquid and solid. In the relative temperature between 14 and 30degC, the temperature dependence on the erosion rate is due to the increase in vapor pressure. (author)

Detecting Anthropogenic Disturbance on Weathering and Erosion Processes

Science.gov (United States)

Vanacker, V.; Schoonejans, J.; Bellin, N.; Ameijeiras-Mariño, Y.; Opfergelt, S.; Christl, M.

2014-12-01

Anthropogenic disturbance of natural vegetation can profoundly alter the physical, chemical and biological processes within soils. Rapid removal of topsoil during intense farming can result in an imbalance between soil production through chemical weathering and physical erosion, with direct implications on local biogeochemical cycling. However, the feedback mechanisms between soil erosion, chemical weathering and biogeochemical cycling in response to anthropogenic forcing are not yet fully understood. In this paper, we analyze dynamic soil properties for a rapidly changing anthropogenic landscape in the Spanish Betic Cordillera; and focus on the coupling between physical erosion, soil production and soil chemical weathering. Modern erosion rates were quantified through analysis of sediment deposition volumes behind check dams, and represent catchment-average erosion rates over the last 10 to 50 years. Soil production rates are derived from in-situ produced 10Be nuclide concentrations, and represent long-term flux rates. In each catchment, soil chemical weathering intensities were calculated for two soil-regolith profiles. Although Southeast Spain is commonly reported as the European region that is most affected by land degradation, modern erosion rates are low (140 t ha-1 yr-1). About 50 % of the catchments are losing soils at a rate of less than 60 t km-2 yr-1. Our data show that modern erosion rates are roughly of the same magnitude as the long-term or cosmogenically-derived erosion rates in the Betic Cordillera. Soils developed on weathered metamorphic rocks have no well-developed profile characteristics, and are generally thin and stony. Nevertheless, soil chemical weathering intensities are high; and question the occurrence of past soil truncation.

Quantifying coastal erosion rates using anatomical change in exposed tree roots at Porquerolles Island (Var, France).

Science.gov (United States)

Morel, Pauline; Corona, Christophe; Lopez-Saez, Jérôme; Rovéra, Georges; Dewez, Thomas; Stoffel, Markus; Berger, Frédéric

2017-04-01

tree roots: Two examples from central Spain. Catena 64 : 81-102. Fantucci R. 2007. Dendrogeomorphological analysis of shore erosion along Bolsena lake (central Italy). Dendrochronologia 24 : 130-140. Giuliano J. Érosion des falaises de la région Provence-Alpes-Côte d'Azur : évolution et origine de la morphologie côtière en Méditerranée : télédétection, géochronologie, géomorphologie. Sciences de la Terre. Université Nice Sophia Antipolis, 2015. Français. . Hitz O, Gärtner H, Heinrich I, Monbaron M, 2008a. Application of ash (Fraxinus excelsior l.) roots to determine erosion rates in mountain torrents. Catena 72 : 248-258. Lopez Saez J, Corona C, Stoffel M, Rovéra G, Astrade L, Berger F. 2011. Mapping of erosion rates in marly badlands based on a coupling of anatomical changes in exposed roots with slope maps derived from LiDAR data. Earth Surface Processes and Landforms 36 : 1162-1171. Lucía, A., Laronne, J. B., & Martín-Duque, J. F. (2011). Geodynamic processes on sandy slope gullies in central Spain field observations, methods and measurements in a singular system. Geodinámica acta, 24(2), 61-79. Malik I. 2008. Dating of small gully formation and establishing erosion rates in old gullies under forest by means of anatomical changes in exposed tree roots (Southern Poland). Geomorphology 93 : 421-436.
 Malik I. 2006. Gully erosion dating by means of anatomical changes in exposed roots (Proboszczowicka plateau, Southern Poland). Geochronometria 25 : 57-66. Stoffel M, Casteller A, Luckman B H, Villalba R, 2012. Spatiotemporal analysis of channel wall erosion in ephemeral torrents using tree roots - An example from the Patagonian Andes. Geology40 : 247-250. Vandekerckhove L. 2001. Short-term bank gully retreat rates in Mediterranean environments. Catena 44 : 133-161.

Effects of oil on the rate and trajectory of Louisiana marsh shoreline erosion

International Nuclear Information System (INIS)

McClenachan, Giovanna; Eugene Turner, R; Tweel, Andrew W

2013-01-01

Oil can have long-term detrimental effects on marsh plant health, both above- and belowground. However, there are few data available that quantify the accelerated rate of erosion that oil may cause to marshes and the trajectory of change. Between November 2010 and August 2012, we collected data on shoreline erosion, soil strength, per cent cover of Spartina alterniflora, and marsh edge overhang at 30 closely spaced low oil and high oil sites in Bay Batiste, Louisiana. Surface oil samples were taken one meter into the marsh in February 2011. All high oiled sites in Bay Batiste were contaminated with Macondo 252 oil (oil from the Deepwater Horizon oil spill, 20 April–15 July 2010). The results suggest that there is a threshold where soil parameters change dramatically with a relatively small increase in oil concentration in the soil. Heavy oiling weakens the soil, creating a deeper undercut of the upper 50 cm of the marsh edge, and causing an accelerated rate of erosion that cascades along the shoreline. Our results demonstrate that it could take at least 2 yr to document the effects heavy oiling has had on the marsh shoreline. The presence of aboveground vegetation alone may not be an appropriate indicator of recovery. (letter)

Erosivity, surface runoff, and soil erosion estimation using GIS-coupled runoff-erosion model in the Mamuaba catchment, Brazil.

Science.gov (United States)

Marques da Silva, Richarde; Guimarães Santos, Celso Augusto; Carneiro de Lima Silva, Valeriano; Pereira e Silva, Leonardo

2013-11-01

This study evaluates erosivity, surface runoff generation, and soil erosion rates for Mamuaba catchment, sub-catchment of Gramame River basin (Brazil) by using the ArcView Soil and Water Assessment Tool (AvSWAT) model. Calibration and validation of the model was performed on monthly basis, and it could simulate surface runoff and soil erosion to a good level of accuracy. Daily rainfall data between 1969 and 1989 from six rain gauges were used, and the monthly rainfall erosivity of each station was computed for all the studied years. In order to evaluate the calibration and validation of the model, monthly runoff data between January 1978 and April 1982 from one runoff gauge were used as well. The estimated soil loss rates were also realistic when compared to what can be observed in the field and to results from previous studies around of catchment. The long-term average soil loss was estimated at 9.4 t ha(-1) year(-1); most of the area of the catchment (60%) was predicted to suffer from a low- to moderate-erosion risk (soil erosion was estimated to exceed > 12 t ha(-1) year(-1). Expectedly, estimated soil loss was significantly correlated with measured rainfall and simulated surface runoff. Based on the estimated soil loss rates, the catchment was divided into four priority categories (low, moderate, high and very high) for conservation intervention. The study demonstrates that the AvSWAT model provides a useful tool for soil erosion assessment from catchments and facilitates the planning for a sustainable land management in northeastern Brazil.

Prediction of long-term erosion from landfill covers in the southwest

International Nuclear Information System (INIS)

Anderson, C.E.; Stormont, J.C.

1997-01-01

Erosion is a primary stressor of landfill covers, especially for climates with high intensity storms and low native plant density. Rills and gullies formed by discrete events can damage barrier layers and induce failure. Geomorphologic, empirical and physical modeling procedures are available to provide estimates of surface erosion, but numerical modeling requires accurate representation of the severe rainfall events that generate erosion. The National Weather Service precipitation frequency data and estimates of 5, 10, 15, 30 and 60-minute intensity can be statistically combined in a numerical model to obtain long-term erosion estimates. Physically based numerical models using the KINEROS and AHYMO programs have been utilized to predict the erosion from a southwestern landfill or waste containment site with 0.03, 0.05 and 0.08 meter per meter surface slopes. Results of AHYMO modeling were within 15 percent of average annual values computed with the empirical Universal Soil Loss Equation. However, the estimation of rill and gully formation that primarily degrades cover systems requires quantifying single events. For Southwestern conditions, a single 10-year storm can produce erosion quantifies equal to three times the average annual erosion and a 100-year storm can produce five times the average annual erosion

Impacts of the post-fire erosion processes compared with the agricultural erosion rates for a mountain catchment in NW Iberia

Science.gov (United States)

Marisa Santos, Juliana; Nunes, João Pedro; Bernard-Jannin, Léonard; Gonzalez Pelayo, Oscar; Keizer, Jan Jacob

2014-05-01

after forest fires. The last forest fire in August 2011 burned 10% of the total area in the north-west part of the catchment. Post-fire management operations 9 month after the fire (clear-cutting and deep plowing operations) and after plantation of "Quercus robur" left the soil exposed, and relatively mild rainstorms led to large amounts of soil loss, including a large amount of rills and other erosion features. This constituted an opportunity to compare these erosion rates with the ones observed in agricultural fields for similar edapho-climatic conditions, and also observe distinct timing of erosion occurrence which was linked with different periods when soils are exposed. This communication presents the assessment of the impact of this fire on soil erosion rates, where results indicate that soil losses after soil preparation for forest replanting might be equivalent, in long-term, to soil losses in agricultural fields.

A 30000 yr record of erosion rates from cosmogenic 10Be in middle European river terraces

NARCIS (Netherlands)

Schaller, M.; Blanckenburg, von F.; Veldkamp, A.; Tebbens, L.A.; Hovius, N.; Kubik, P.W.

2002-01-01

Cosmogenic 10Be in river-borne quartz sand records a time-integrated erosion rate representative of an entire drainage basin. When sequestered in a terrace of known age, paleo-erosion rates may be recovered from the nuclide content of the terrace material. Paleo-erosion rates between 30 and 80

Long-Term Analysis for Harvest Erosion Caused by Sugar Beet Production in Turkey

Directory of Open Access Journals (Sweden)

Selen DEVİREN SAYGIN

2018-02-01

Full Text Available The sustainability of soil resources is under significant threat due to the accelerated anthropogenic pressures at the historical expansion of human population. In this context, soil erosion is defined as a limiting factor for human interests in terms of ecosystem services. As an erosion type, harvest erosion occurs by harvesting of the taproot and tuberous root plants such as sugar beet (Beta vulgaris L., potato (Solanum tuberosum L., carrot (Daucus carota L. and chicory (Cichorium intybus L., has begun to take attention in recent years. The objective of this study was to estimate soil loss due to harvest erosion and to economically analyze the transport of plant nutrients between 1999 and 2016 from sugar beet growing areas in Turkey. For this aim, the compiled data of 25 different sugar factories throughout Turkey were obtained from Türkşeker and soil loss estimations were performed and economically analyzed. According to the results, average soil loss rate was calculated as 3.41 Mg ha-1y-1 for the studied period (1999-2016. That means annually an average of 716983 Mg soil removed from the Türkşeker sugar beet production areas. This result indicated that harvest erosion represents only 0.9% of soil lost by water erosion in Turkey. But, if tolerable soil loss value considered as “1 Mg ha-1 y-1”, calculated soil loss values are above this critical value for all the factories. In addition, economic assessments of soil losses showed that costs are to be more than US $10 000 annually on the 60% of the factories due to removal of plant nutrients with harvest process. And, annually US $419 433 investment must be made to recover all these losses. Conclusively, harvest erosion as an ignored erosion type must be emphasized to the economic sustainability of natural resources in fragile ecosystems such as our country.

IN SITU MEASUREMENT OF BEDROCK EROSION

Directory of Open Access Journals (Sweden)

D. H. Rieke-Zapp

2012-07-01

Full Text Available While long term erosion rates of bedrock material may be estimated by dating methods, current day erosion rates are – if at all available – based on rough estimates or on point measurements. Precise quantification of short term erosion rates are required to improve our understanding of short term processes, for input in landscape evolution models, as well as for studying the mechanics and efficiency of different erosion processes in varying geomorphological settings. Typical current day erosion rates in the European Alps range from sub-millimetre to several millimetres per year depending on the dominant erosion processes. The level of surveying accuracy required for recurring sub-millimetre to millimetre measurements in the field is demanding. A novel surveying setup for in-situ measurement of bedrock erosion was tested recently in three different locations in Switzerland. Natural bedrock was investigated in the Gornera gorge close to Zermatt. Further on, bedrock samples were installed in exposed locations in the Erlenbach research watershed close to Einsiedeln, and in the Illgraben debris flow channel, located in the Canton Schwyz and Valais, respectively. A twofold measurement approach was chosen for all locations. For the first setup control points providing an absolute reference frame for recurrent measurements were embedded close to the area of interest. Close range photogrammetry was applied to measure surface changes on the bedrock samples. The precision for surface measurements in the field was 0.1 mm (1 σ and thus suitable for the application. The equipment needed for the surveys can easily be carried to the field. At one field site a structured light scanner was used along with the photogrammetric setup. Although the current generation of structured light scanners appeared less suitable for field application, data acquisition was much faster and checking the data for completeness in the field was straight forward. The latest

In Situ Measurement of Bedrock Erosion

Science.gov (United States)

Rieke-Zapp, D. H.; Beer, A.; Turowski, J. M.; Campana, L.

2012-07-01

While long term erosion rates of bedrock material may be estimated by dating methods, current day erosion rates are - if at all available - based on rough estimates or on point measurements. Precise quantification of short term erosion rates are required to improve our understanding of short term processes, for input in landscape evolution models, as well as for studying the mechanics and efficiency of different erosion processes in varying geomorphological settings. Typical current day erosion rates in the European Alps range from sub-millimetre to several millimetres per year depending on the dominant erosion processes. The level of surveying accuracy required for recurring sub-millimetre to millimetre measurements in the field is demanding. A novel surveying setup for in-situ measurement of bedrock erosion was tested recently in three different locations in Switzerland. Natural bedrock was investigated in the Gornera gorge close to Zermatt. Further on, bedrock samples were installed in exposed locations in the Erlenbach research watershed close to Einsiedeln, and in the Illgraben debris flow channel, located in the Canton Schwyz and Valais, respectively. A twofold measurement approach was chosen for all locations. For the first setup control points providing an absolute reference frame for recurrent measurements were embedded close to the area of interest. Close range photogrammetry was applied to measure surface changes on the bedrock samples. The precision for surface measurements in the field was 0.1 mm (1 σ) and thus suitable for the application. The equipment needed for the surveys can easily be carried to the field. At one field site a structured light scanner was used along with the photogrammetric setup. Although the current generation of structured light scanners appeared less suitable for field application, data acquisition was much faster and checking the data for completeness in the field was straight forward. The latest generation of compact

Soil carbon and nitrogen erosion in forested catchments: implications for erosion-induced terrestrial carbon sequestration

Science.gov (United States)

E. M. Stacy; S. C. Hart; C. T. Hunsaker; D. W. Johnson; A. A. Berhe

2015-01-01

Lateral movement of organic matter (OM) due to erosion is now considered an important flux term in terrestrial carbon (C) and nitrogen (N) budgets, yet most published studies on the role of erosion focus on agricultural or grassland ecosystems. To date, little information is available on the rate and nature of OM eroded from forest ecosystems. We present annual...

Erosion rates across space and timescales from a multi-proxy study of rivers of eastern Taiwan

Science.gov (United States)

Fellin, Maria Giuditta; Chen, Chia-Yu; Willett, Sean D.; Christl, Marcus; Chen, Yue-Gau

2017-10-01

We derive erosion rates from detrital zircon fission-track ages and cosmogenic nuclide concentrations from sediments from the modern rivers of eastern Taiwan in order to investigate how surface erosional processes vary in space and time across the young arc-continent collisional orogen of Taiwan. Taiwan is characterized by rapid rates of exhumation, a fluvial and landslide-dominated landscape, high seismicity, high relief and frequent typhoons. The obliquity between the convergence direction and the trend of the plate boundary provides a gradient in uplift and variations in longevity of orogenic activity with a young, immature orogen in the south, a mature orogen in central and northern Taiwan, and perhaps even the cessation of orogeny in the far north. The modern zircon fission-track detrital record is consistent with basement ages that show that much of the orogen is eroding at high rates with basin-wide mean zircon fission-track cooling ages as young as 0.9 Ma. The erosion rates derived from concentrations of cosmogenic nuclides (10Be) provide erosion rates averaged over much shorter timescales, but these two proxies provide estimates of erosion rates that are within error of each other across most of the collisional belt. Erosion rates are lowest in the immature zone of the orogen (Taiwan, and increase to values ≥ 4 km/Ma in central Taiwan. Geomorphic indices, in particular channel steepness, are also correlated with erosion rates, suggesting that fluvial erosion is the dominant exhumation process and that landscape evolution is reacting primarily to tectonic forcing, fast enough to keep the landscape in a state of quasi-equilibrium where erosion rates and rock uplift rates are nearly equal. We find no measurable effects due to rock erodibility or precipitation rate, but if these parameters co-vary with tectonic uplift rate, our data could not resolve the influence of each.

Hillslope-channel coupling in a steep Hawaiian catchment accelerates erosion rates over 100-fold

Science.gov (United States)

Stock, J. D.; Hanshaw, M. N.; Rosener, M.; Schmidt, K. M.; Brooks, B. A.; Tribble, G.; Jacobi, J.

2009-12-01

season. During Fall storms, sediment concentration is often 10X higher at a given stage. During intense Fall storms, we measured erosion rates using erosion pins (1.0 cm/a), suspended sediment flux (1.5 cm/a) and repeat tripod LiDAR (1.7 cm/a). These rates are at least 100-fold greater than the long-term lowering rate of 0.13 mm/a. A sediment budget constructed by extrapolating hillslope lowering rates to the portions of the catchments mapped as overland flow hotspots predicts a total yearly flux of ~ 6500 t, in agreement with the measured total of ~6200 t. A decadal record illustrates that rainfall intensities sufficient to generate overland flow occur for at least 8-10 hours every year, coincident with 1-3 large storm events. We hypothesize that high lowering rates reflect a combination of long-duration overland flow events, and availability of weathered soils that can be entrained by thin flows. It appears that the generation of loose, seasonally weathered silt is a 1st order control on the amount of sediment exported to the reef. If climate change increases storm frequency or duration, or decreases vegetation cover, sediment loading rates to the reef here could increase dramatically.

Simulation of long-term erosion on an abandoned mine site using the SIBERIA landscape evolution model

International Nuclear Information System (INIS)

Hancock, G.; Willgoose, G.; Evans, K.

1999-01-01

The SIBERIA catchment evolution model can simulate the evolution of landforms over many years as a result of runoff and erosion. This study discusses testing of the reliability of the erosion predictions of the model in a field study. Using erosion parameters calibrated from field studies of rainfall and runoff from the waste rock dump batters, the SIBERIA landscape evolution model was calibrated and then used to simulate erosion over 50 years on the abandoned Scinto 6 mine site. Scinto 6 is a former uranium mine located in the Kakadu Region, Northern Territory, Australia. The SIBERIA runs simulated the geomorphic development of the gullies on the man-made batters of the waste rock dump. The waste rock of the mine had been dumped in the characteristic pattern of a flat top and steep sided batters typical of many former and current dumps and there had been significant degradation from both sheet and gully erosion. Traditional erosion models cannot model this type of degradation because their erosion model cannot change the landform, while SIBERIA does change the landform. The gully position, depth volume and morphology on the waste rock dump were compared with that of SIBERIA simulations. The geomorphic development of the waste rock dump indicated that SIBERIA can simulate features that arise from the long-term effect of erosion and also their rate of development on a man-made post-mining landscape over periods of up to 50 years. The detailed results of this specific study will be discussed with specific discussion of the type of data required and the implications of the uncertain erosion physics on the reliability of the predictions

Evaluation of rate of swelling and erosion of verapamil (VRP) sustained-release matrix tablets.

Science.gov (United States)

Khamanga, Sandile M; Walker, Roderick B

2006-01-01

Tablets manufactured in-house were compared to a marketed sustained-release product of verapamil to investigate the rate of hydration, erosion, and drug-release mechanism by measuring the wet and subsequent dry weights of the products. Swelling and erosion rates depended on the polymer and granulating fluid used, which ultimately pointed to their permeability characteristics. Erosion rate of the marketed product was highest, which suggests that the gel layer that formed around these tablets was weak as opposed to the robust and resistant layers of test products. Anomalous and near zero-order transport mechanisms were dominant in tests and commercial product, respectively.

Extracting information on the spatial variability in erosion rate stored in detrital cooling age distributions in river sands

Science.gov (United States)

Braun, Jean; Gemignani, Lorenzo; van der Beek, Peter

2018-03-01

river distribution. The method additionally allows comparing modern erosion rates to long-term exhumation rates. We provide a simple implementation of the method in Python code within a Jupyter Notebook that includes the data used in this paper for illustration purposes.

Extracting information on the spatial variability in erosion rate stored in detrital cooling age distributions in river sands

Directory of Open Access Journals (Sweden)

J. Braun

2018-03-01

any given catchment to the river distribution. The method additionally allows comparing modern erosion rates to long-term exhumation rates. We provide a simple implementation of the method in Python code within a Jupyter Notebook that includes the data used in this paper for illustration purposes.

Effects of landforms on the erosion rate in a small watershed by the 137Cs tracing method

International Nuclear Information System (INIS)

Li Mian; Yao Wenyi; Li Zhanbin; Liu Puling; Shen Zhenzhou

2010-01-01

It's very important to analyze and evaluate quantitatively the effects of landforms on soil erosion for the prevention and treatment of soil loss in a small watershed. The objective of this study was to evaluate the effects of landform factors on erosion rate by the 137 Cs tracing method in a small watershed in the Purple Hilly Area of China. The erosion rates under different slope lengths, slope gradients and slope aspects were estimated in Xiangshuitan watershed in the Purple Hilly Area in Sichuan Basin by the 137 Cs tracing method. The results showed that the erosion rate decreased exponentially with downslope distance, and it increased with increasing slope gradient during the scope of 5 deg. - 16 deg. The slope aspect had great impact on the erosion rate, and the hillside on the sunny slope had larger erosion rate than that on the shady slope, particularly for the farmland.

Assessment of soil erosion and deposition rates in a Moroccan agricultural field using fallout 137Cs and 210Pbex.

Science.gov (United States)

Benmansour, M; Mabit, L; Nouira, A; Moussadek, R; Bouksirate, H; Duchemin, M; Benkdad, A

2013-01-01

In Morocco land degradation - mainly caused by soil erosion - is one of the most serious agroenvironmental threats encountered. However, only limited data are available on the actual magnitude of soil erosion. The study site investigated was an agricultural field located in Marchouch (6°42' W, 33° 47' N) at 68 km south east from Rabat. This work demonstrates the potential of the combined use of (137)Cs, (210)Pb(ex) as radioisotopic soil tracers to estimate mid and long term erosion and deposition rates under Mediterranean agricultural areas. The net soil erosion rates obtained were comparable, 14.3 t ha(-1) yr(-1) and 12.1 ha(-1) yr(-1) for (137)Cs and (210)Pb(ex) respectively, resulting in a similar sediment delivery ratio of about 92%. Soil redistribution patterns of the study field were established using a simple spatialisation approach. The resulting maps generated by the use of both radionuclides were similar, indicating that the soil erosion processes has not changed significantly over the last 100 years. Over the previous 10 year period, the additional results provided by the test of the prediction model RUSLE 2 provided results of the same order of magnitude. Based on the (137)Cs dataset established, the contribution of the tillage erosion impact has been evaluated with the Mass Balance Model 3 and compared to the result obtained with the Mass Balance Model 2. The findings highlighted that water erosion is the leading process in this Moroccan cultivated field, tillage erosion under the experimental condition being the main translocation process within the site without a significant and major impact on the net erosion. Copyright © 2012 Elsevier Ltd. All rights reserved.

An assessment for the erosion rate of DEMO first wall

Science.gov (United States)

Tokar, M. Z.

2018-01-01

In a fusion reactor a significant fraction of plasma particles lost from the confined volume will reach the vessel wall. The recombination of these charged species, electrons and ions of hydrogen isotopes, is a source of neutral molecules and atoms, recycling back into the plasma. Here they participate, in particular, in charge-exchange (c-x) collisions with the plasma ions and, as a result, atoms of high energies with chaotically oriented velocities are generated. A significant fraction of these hot neutrals will hit the wall, leading, as well as the outflowing fuel and impurity ions, to its erosion, limiting the reactor operation time. The rate of the wall erosion in DEMO is assessed by applying a one-dimensional model which takes into account the transport of charged and neutral species across the flux surfaces in the main part of the scrape-off layer, beyond the X-point vicinity and divertor, and by considering the shift of the centers of flux surfaces, their elongation and triangularity. Atoms generated by c-x of recycling neutrals are modeled kinetically to define firmly their energy spectrum, being of particular importance for the erosion assessment. It is demonstrated the erosion rate of the DEMO wall armor of tungsten will have a pronounced ballooning character with a significant maximum of 0.3 mm per full power year at the low field side, decreasing with an increase in the anomalous perpendicular transport in the ‘far’ SOL or the plasma density at the separatrix.

Constraining local subglacial bedrock erosion rates with cosmogenic nuclides

Science.gov (United States)

Wirsig, Christian; Ivy-Ochs, Susan; Christl, Marcus; Reitner, Jürgen; Reindl, Martin; Bichler, Mathias; Vockenhuber, Christof; Akcar, Naki; Schlüchter, Christian

2014-05-01

The constant buildup of cosmogenic nuclides, most prominently 10Be, in exposed rock surfaces is routinely employed for dating various landforms such as landslides or glacial moraines. One fundamental assumption is that no cosmogenic nuclides were initially present in the rock, before the event to be dated. In the context of glacially formed landscapes it is commonly assumed that subglacial erosion of at least a few meters of bedrock during the period of ice coverage is sufficient to remove any previously accumulated nuclides, since the production of 10Be ceases at a depth of 2-3 m. Insufficient subglacial erosion leads to overestimation of surface exposure ages. If the time since the retreat of the glacier is known, however, a discordant concentration of cosmogenic nuclides delivers information about the depth of subglacial erosion. Here we present data from proglacial bedrock at two sites in the Alps. Goldbergkees in the Hohe Tauern National Park in Austria and Gruebengletscher in the Grimsel Pass area in Switzerland. Samples were taken inside as well as outside of the glaciers' Little Ice Age extent. Measured nuclide concentrations are analyzed with the help of a MATLAB model simulating periods of exposure or glacial cover of user-definable length and erosion rates.

Preliminary assessment of the potential for using cesium-137 technique to estimate rates of soil erosion on cultivated land in La Victoria I, Camaguey province of cuba

International Nuclear Information System (INIS)

Brigido, F.O.; Gandarilla Benitez, J.E.

1999-01-01

Despite a growing awareness that erosion on cultivated land in Cuba is a potential hazard to long term productivity, there is still only limited information on the rates involved, particularly long term values. The potential for using the radionuclide Caesium-137 as an environmental tracer to indicate sources of soil erosion on cultivated soils in La Victoria catchment is introduced. Use of Caesium-137 measurements to estimate rates of erosion and deposition is founded on comparison of the Caesium-137 inventories at individual sampling points with a reference inventory representing the local Caesium fallout input and thus the inventory to be expected at the site experiencing neither erosion nor deposition. Two models for converting Caesium-137 measurements to estimates of soil redistribution rates on studied site have been used, the Proportional Model and Mass Balance Model. Using the first one net soil erosion was calculated to be 17.6 t. Ha 1 - .year 1 - . Estimates of soil loss using a Mass Balance Model (Simplified Model 1 and Model 2) were found to be 30.2 and 30.6 t. Ha 1 - .year 1 - ,respectively. Preliminary results suggest that Caesium-137 technique may be of considerable value in assembling data on the rates and spatial distribution of soil loss and a reliable tool for developing of soil conservation program

Use of 7Be to document soil erosion associated with a short period of extreme rainfall

International Nuclear Information System (INIS)

Sepulveda, A.; Schuller, P.; Walling, D.E.; Castillo, A.

2008-01-01

Intensification and expansion of agricultural production since the 1970s have increased soil erosion problems in south-central Chile. Quantitative information on soil loss is needed for erosion risk assessment and to establish the effectiveness of improved land management practices. Since information from traditional sources, such as erosion plots, is limited, attention has been directed to the use of environmental radionuclides for documenting erosion rates. Cs-137 has been successfully utilised for this purpose, but only provides information on medium-term erosion rates. There is also a need to document event-related soil erosion. This paper outlines the basis for using 7 Be measurements to document short-term erosion and reports its successful use for quantifying the erosion that occurred within an arable field, as a result of a period of heavy rainfall (400 mm in 27 days) occurring in May 2005. The study field had been under a no-till, no-burning system for 18 years, but immediately prior to the period of heavy rainfall the harvest residues were burnt. The erosion recorded therefore reflected both the extreme nature of the rainfall and the effects of the burning in increasing surface runoff and erosion. The sampled area corresponded to that used previously by the authors to document the medium-term erosion rates associated with both conventional tillage and the subsequent switch to a no-till system. Comparisons between the erosion documented for the period of heavy rainfall in 2005 with these medium-term erosion rates permits some tentative conclusions regarding the importance of extreme events and the impact of burning in increasing the erosion associated with the no-till system

Effects of landforms on the erosion rate in a small watershed by the {sup 137}Cs tracing method

Energy Technology Data Exchange (ETDEWEB)

Li Mian, E-mail: hnli-mian@163.co [Yellow River Institute of Hydraulic Research, Key Laboratory of Sediment Research of Yellow River of Ministry of Water Resources, Zhengzhou, Henan 450003 (China); Yao Wenyi [Yellow River Institute of Hydraulic Research, Key Laboratory of Sediment Research of Yellow River of Ministry of Water Resources, Zhengzhou, Henan 450003 (China); Li Zhanbin [Xi' an University of Technology, Xi' an, Shaanxi 710048 (China); Institute of Soil and Water Conservation, Chinese Academy of Sciences and Ministry of Water Resources, Yangling, Shaanxi 712100 (China); Liu Puling [Institute of Soil and Water Conservation, Chinese Academy of Sciences and Ministry of Water Resources, Yangling, Shaanxi 712100 (China); Shen Zhenzhou [Yellow River Institute of Hydraulic Research, Key Laboratory of Sediment Research of Yellow River of Ministry of Water Resources, Zhengzhou, Henan 450003 (China)

2010-05-15

It's very important to analyze and evaluate quantitatively the effects of landforms on soil erosion for the prevention and treatment of soil loss in a small watershed. The objective of this study was to evaluate the effects of landform factors on erosion rate by the {sup 137}Cs tracing method in a small watershed in the Purple Hilly Area of China. The erosion rates under different slope lengths, slope gradients and slope aspects were estimated in Xiangshuitan watershed in the Purple Hilly Area in Sichuan Basin by the {sup 137}Cs tracing method. The results showed that the erosion rate decreased exponentially with downslope distance, and it increased with increasing slope gradient during the scope of 5 deg. - 16 deg. The slope aspect had great impact on the erosion rate, and the hillside on the sunny slope had larger erosion rate than that on the shady slope, particularly for the farmland.

Modeling the fluid/soil interface erosion in the Hole Erosion Test

Directory of Open Access Journals (Sweden)

Kissi B.

2012-07-01

Full Text Available Soil erosion is a complex phenomenon which yields at its final stage to insidious fluid leakages under the hydraulic infrastructures known as piping and which are the main cause of their rupture. The Hole Erosion Test is commonly used to quantify the rate of piping erosion. In this work, The Hole Erosion Test is modelled by using Fluent software package. The aim is to predict the erosion rate of soil during the hole erosion test. The renormalization group theory – based k–ε turbulence model equations are used. This modelling makes it possible describing the effect of the clay concentration in flowing water on erosion. Unlike the usual one dimensional models, the proposed modelling shows that erosion is not uniform erosion along the hole length. In particular, the concentration of clay is found to increase noticeably the erosion rate.

Assessing soil erosion rates for a large catchment in the Central Highlands of Vietnam using fallout radionuclides

International Nuclear Information System (INIS)

Phan Son Hai; Nguyen Thanh Binh; Nguyen Minh Dao; Nguyen Thi Huong Lan; Nguyen Thi Mui; Le Xuan Thang; Phan Quang Trung; Trinh Cong Tu; Tran Tien Dung

2014-01-01

Fallout radionuclides Be-7 and Cs-137 were applied to assess soil erosion rates for a 270.5 km 2 catchment with a variety of slope (from 0 o to more than 45 o , crops or vegetation (natural forest, artificial forest, perennial crops, annual crops) and a variety of tillage and soil conservation measures. Soil erosion rates were estimated at 90 areas within the catchment. Each sampling area has at least one feature of the slope, rainfall, crops, farming practice different from others. Soil erosion rates in this region depend significantly on the slope, crops and farming techniques. Averaging over crops, soil erosion rates by slopes 0 - 5 o , 5 - 15 o , 15 - 25 o and 25 - 35 o are 5.0, 12.8, 18.9 and 21.3 t.ha -1 .y -1 , respectively. Forest land has the least soil erosion rates, ranging between 0.5 t.ha -1 .y -1 and 14 t.ha -1 .y -1 depending on the slope. Annual crops land has the highest soil erosion rates, ranging between 6 t.ha -1 .y -1 and 42 t.ha -1 .y -1 when slope varies from < 5 o to 32 o . Perennial crop land has soil erosion rates in the range of 5 t.ha -1 .y -1 and 39 t.ha -1 .y -1 . In areas with the same slope, the soil erosion rate is the highest for cashew plantations, lower for mulberry field and the lowest for tea or coffee plantations. Soil erosion has resulted in losing a significant quantity of plant nutrients such as OM, N, P 2 O 5 and K 2 O every year. Generally, lost nutrient quantities due to soil erosion are proportional to erosion rates. Some areas of annual crop land lost a large amount of nutrients every year, up to 1435 kg OM, 79 kg N, 54 kg P 2 O 5 and 36 kg K 2 O. Similarly, perennial crop lands in this region could lost up to 1736 kg OM, 91 kg N, 66 kg P 2 O 5 and 40 kg K 2 O every year. Owing to soil erosion, the catchment has lost about 211200 tons of surface soil per year during last 50 years, corresponding to the rate of 7.8 t.ha -1 .y -1 . This amount of eroded soil was deposited in drainage of the catchment and in reservoirs

Quantifying modern erosion rates and river-sediment contamination in the Bolivian Andes

Science.gov (United States)

Vezzoli, Giovanni; Ghielmi, Giacomo; Mondaca, Gonzalo; Resentini, Alberto; Villarroel, Elena Katia; Padoan, Marta; Gentile, Paolo

2013-08-01

We use petrographic, mineralogical and geochemical data on modern river sediments of the Tupiza basin in the Bolivian Andes to investigate the relationships among human activity, heavy-metal contamination of sediments and modern erosion rates in mountain fluvial systems. Forward mixing model was used to quantify the relative contributions from each main tributary to total sediment load of the Tupiza River. The absolute sediment load was estimated by using the Pacific Southwest Inter Agency Committee model (PSIAC, 1968) after two years of geological field surveys (2009; 2010), together with data obtained from the Instituto Nacional del Agua public authority (INA, 2007), and suspended-load data from Aalto et al. (2006). Our results indicate that the sediment yield in the drainage basin is 910 ± 752 ton/km2year and the mean erosion rate is 0.40 ± 0.33 mm/year. These values compare well with erosion rates measured by Insel et al. (2010) using 10Be cosmogenic radionuclide concentrations in Bolivian river sediments. More than 40% of the Tupiza river load is produced in the upper part of the catchment, where highly tectonized and weathered rocks are exposed and coupled with sporadic land cover and intense human activity (mines). In the Rio Chilco basin strong erosion of upland valleys produce an increase of erosion (˜10 mm/year) and the influx of large amounts of sediment by mass wasting processes. The main floodplain of the Tupiza catchment represents a significant storage site for the heavy metals (˜657 ton/year). Fluvial sediments contain zinc, lead, vanadium, chromium, arsenic and nickel. Since the residence time of these contaminants in the alluvial plain may be more than 100 years, they may represent a potential source of pollution for human health.

Increase in the rate and uniformity of coastline erosion in Arctic Alaska

Science.gov (United States)

Jones, Benjamin M.; Arp, C.D.; Jorgenson, M.T.; Hinkel, Kenneth M.; Schmutz, J.A.; Flint, P.L.

2009-01-01

Analysis of a 60 km segment of the Alaskan Beaufort Sea coast using a time-series of aerial photography revealed that mean annual erosion rates increased from 6.8 m a-1 (1955 to 1979), to 8.7 m a-1 (1979 to 2002), to 13.6 m a-1 (2002 to 2007). We also observed that spatial patterns of erosion have become more uniform across shoreline types with different degrees of ice-richness. Further, during the remainder of the 2007 ice-free season 25 m of erosion occurred locally, in the absence of a westerly storm event. Concurrent arctic changes potentially responsible for this shift in the rate and pattern of land loss include declining sea ice extent, increasing summertime sea surface temperature, rising sea-level, and increases in storm power and corresponding wave action. Taken together, these factors may be leading to a new regime of ocean-land interactions that are repositioning and reshaping the Arctic coastline. Copyright 2009 by the American Geophysical Union.

Effect of hard second-phase particles on the erosion resistance of model alloys

International Nuclear Information System (INIS)

Kosel, T.H.; Aptekar, S.S.

1986-01-01

The dependence of erosion rate on second phase volume fraction (SPVF) has been studied for Cu/Al/sub 2/O/sub 3/ and Cu/WC(W/sub 2/C) model alloys produced by pressing and sintering. The intention was to investigate the reasons for the poor contribution to erosion resistance made by large hard second phase particles (SPP) in other studies. The results show that for Cu/Al/sub 2/O/sub 3/ alloys, the erosion rate generally increased with SPVF, demonstrating a negative contribution to erosion resistance. This occurred despite the fact that the measured erosion rate of monolithic Al/sub 2/O/sub 3/ was lower by one to two orders of magnitude than that of the pure matrix. Changing from severe erosion with large erodent particles at high velocity to mild conditions with small erodent at low velocity caused a change from depression of the SPPs to protrusion from the surface, with some improvement of the relative erosion resistance compared to the pure matrix. For Cu/WC(W/sub 2/C) alloys, changing from severe to mild erosion conditions caused a change from an increase of erosion with SPVF to a decrease. The results are discussed in terms of the increased microfracture of the unsupported edges of the second phase particles compared to a flat single-phase surface. This edge is consistent with the results, and explains observations not predicted by existing theories for erosion of single-phase materials. A model is introduced which predicts a new averaging law for the erosion rate of a two-phase alloy in terms of erosion rates of its constituent phases

Can control of soil erosion mitigate water pollution by sediments?

Science.gov (United States)

Rickson, R J

2014-01-15

The detrimental impact of sediment and associated pollutants on water quality is widely acknowledged, with many watercourses in the UK failing to meet the standard of 'good ecological status'. Catchment sediment budgets show that hill slope erosion processes can be significant sources of waterborne sediment, with rates of erosion likely to increase given predicted future weather patterns. However, linking on-site erosion rates with off-site impacts is complicated because of the limited data on soil erosion rates in the UK and the dynamic nature of the source-pathway-receptor continuum over space and time. Even so, soil erosion control measures are designed to reduce sediment production (source) and mobilisation/transport (pathway) on hill slopes, with consequent mitigation of pollution incidents in watercourses (receptors). The purpose of this paper is to review the scientific evidence of the effectiveness of erosion control measures used in the UK to reduce sediment loads of hill slope origin in watercourses. Although over 73 soil erosion mitigation measures have been identified from the literature, empirical data on erosion control effectiveness are limited. Baseline comparisons for the 18 measures where data do exist reveal erosion control effectiveness is highly variable over time and between study locations. Given the limitations of the evidence base in terms of geographical coverage and duration of monitoring, performance of the different measures cannot be extrapolated to other areas. This uncertainty in effectiveness has implications for implementing erosion/sediment risk reduction policies, where quantified targets are stipulated, as is the case in the EU Freshwater Fish and draft Soil Framework Directives. Also, demonstrating technical effectiveness of erosion control measures alone will not encourage uptake by land managers: quantifying the costs and benefits of adopting erosion mitigation is equally important, but these are uncertain and difficult to

Establishment of the relationship between 137Cs loss and soil erosion rates

International Nuclear Information System (INIS)

Phan Son Hai

2003-01-01

The key stages involved in the use of 137 Cs in soil erosion assessment is presented. The method have been successfully applied in pilot scale. These main stages can be summarized as follows: 1/ selection of reference sites next to the study site and establishment of a reference fallout inventory for the study site; 2/measurement of the current spatial distribution of 137 Cs inventory; 3/ evaluation of the pattern of 137 Cs redistribution at the study site; 4/ development of a calibration relationship between 137 CS loss and gain and rate of soil erosion; 5/ estimation of soil redistribution rates using the calibration relationship. (PSH)

Holocene versus modern catchment erosion rates at 300 MW Baspa II hydroelectric power plant (India, NW Himalaya)

Science.gov (United States)

Draganits, Erich; Gier, Susanne; Hofmann, Christa-Ch.; Janda, Christoph; Bookhagen, Bodo; Grasemann, Bernhard

2014-08-01

300 MW Baspa II is India's largest private hydroelectric facility, located at the Baspa River which is an important left-hand tributary to the Sutlej River in the NW Himalaya (India). In this valley the Sangla palaeo-lake has been dammed around 8200 yr BP behind a rock-avalanche dam and Baspa II is located exactly on top of this palaeo-lake. This special location represents a very rare possibility to evaluate the short-term, river load and hydrological parameters measured during the planning and operational stages of Baspa II with the long-term parameters gained from the palaeo-lake sediments from the catchment. Sedimentological and geomorphological investigations of the lacustrine sediments have been used to reconstruct environmental changes during >2500 years of its existence. The Mid-Holocene erosion rates of the Baspa catchment estimated from the volume and duration of deposition of the exposed lake sediments are at 0.7-1.0 mm yr-1, almost identical with the modern erosion rates calculated from river gauge data from Baspa II. Several charcoal layers and charcoal pieces from the uppermost palaeo-lake levels around 5000 cal yr BP might be related to woodland clearance and they possibly represent one of the oldest evidences for human presence in the Baspa Valley during Neolithic time.

Erosion of soil organic carbon: implications for carbon sequestration

Science.gov (United States)

Van Oost, Kristof; Van Hemelryck, Hendrik; Harden, Jennifer W.; McPherson, B.J.; Sundquist, E.T.

2009-01-01

Agricultural activities have substantially increased rates of soil erosion and deposition, and these processes have a significant impact on carbon (C) mineralization and burial. Here, we present a synthesis of erosion effects on carbon dynamics and discuss the implications of soil erosion for carbon sequestration strategies. We demonstrate that for a range of data-based parameters from the literature, soil erosion results in increased C storage onto land, an effect that is heterogeneous on the landscape and is variable on various timescales. We argue that the magnitude of the erosion term and soil carbon residence time, both strongly influenced by soil management, largely control the strength of the erosion-induced sink. In order to evaluate fully the effects of soil management strategies that promote carbon sequestration, a full carbon account must be made that considers the impact of erosion-enhanced disequilibrium between carbon inputs and decomposition, including effects on net primary productivity and decomposition rates.

Estimating the erosion and deposition rates in a small watershed by the 137Cs tracing method

International Nuclear Information System (INIS)

Li Mian; Li Zhanbin; Yao Wenyi; Liu Puling

2009-01-01

Understanding the erosion and deposition rates in a small watershed is important for designing soil and water conservation measures. The objective of this study is to estimate the net soil loss and gain at points with various land use types and landform positions in a small watershed in the Sichuan Hilly Basin of China by the 137 Cs tracing technique. Among various land use types, the order of erosion rate was bare rock > sloping cultivated land > forest land. The paddy field and Caotu (a kind of cultivated land located at the foot of hills) were depositional areas. The erosion rate under different landform was in this order: hillside > saddle > hilltop. The footslope and the valley were depositional areas. The 137 Cs technique was shown to provide an effective means of documenting the spatial distribution of soil erosion and deposition within the small watershed

Medium-term erosion simulation of an abandoned mine site using the SIBERIA landscape evolution model

International Nuclear Information System (INIS)

Hancock, G.R.; Willgoose, G.R.

2000-01-01

This study forms part of a collaborative project designed to validate the long-term erosion predictions of the SIBERIA landform evolution model on rehabilitated mine sites. The SIBERIA catchment evolution model can simulate the evolution of landforms resulting from runoff and erosion over many years. SIBERIA needs to be calibrated before evaluating whether it correctly models the observed evolution of rehabilitated mine landforms. A field study to collect data to calibrate SIBERIA was conducted at the abandoned Scinto 6 uranium mine located in the Kakadu Region, Northern Territory, Australia. The data were used to fit parameter values to a sediment loss model and a rainfall-runoff model. The derived runoff and erosion model parameter values were used in SIBERIA to simulate 50 years of erosion by concentrated flow on the batters of the abandoned site. The SIBERIA runs correctly simulated the geomorphic development of the gullies on the man-made batters of the waste rock dump. The observed gully position, depth, volume, and morphology on the waste rock dump were quantitatively compared with the SIBERIA simulations. The close similarities between the observed and simulated gully features indicate that SIBERIA can accurately predict the rate of gully development on a man-made post-mining landscape over periods of up to 50 years. SIBERIA is an appropriate model for assessment of erosional stability of rehabilitated mine sites over time spans of around 50 years. Copyright (2000) CSIRO Australia

Effect of soil erosion on the long-term stability of FUSRAP near-surface waste-burial sites

International Nuclear Information System (INIS)

Knight, M.J.

1983-04-01

Decontamination of FUSRAP sites could result in the generation of large volumes (in excess of 400,000 m 3 ) of low-activity radioactive wastes (primarily contaminated soil and building materials) requiring subsequent disposal. It is likely that near-surface burial will be seriously considered as an option for disposal of these materials. A number of factors - including soil erosion - could adversely affect the long-term stability of a near-surface waste-burial site. The majority of FUSRAP sites are located in the humid eastern United States, where the principal cause of erosion is the action of water. This report examines the effect of soil erosion by water on burial-site stability based on analysis of four hypothetical near-surface burial sites. The Universal Soil Loss Equation was employed to estimate average annual soil loss from burial sites and the 1000-year effects of soil loss on the soil barrier (burial trench cap) placed over low-activity wastes. Results suggest that the land use of the burial site and the slope gradient of the burial trench cap significantly affect the rate of soil erosion. The development of measures limiting the potential land use of a burial site (e.g., mixing large rocks into the burial trench cap) may be required to preserve the integrity of a burial trench for long periods of time

Determination of Redistribution of Erosion/Deposition Rate in Cultivated Area Using 137Cs Technique

International Nuclear Information System (INIS)

Nita Suhartini; Syamsul Abbas RAS; Barokah A; Ali Arman L

2004-01-01

The aim of the research is to determine the rate of redistribution of erosion/deposition in cultivated area. The application of 137 Cs technique was carried out at cultivated area in Bojong - Ciawi, with slope less than 10 o and slope length of about 2 km. A reference site was selected at the top of the slope, and this site is flat, open and covered with grass. Two sites in the cultivated area were selected as study site namely LU-I ( 15 x 25 ) m with the distance of 1000 m from the top, and LU-II (17.5 x 20) m with the distance of 1300 m from the top. Sampling of soil at reference site was done by using scraper (20 x 50) cm, while sampling at study site by using core sampling (di = 7 cm). Soil samples were brought to the laboratorium for preparation and analysis of 137 Cs content. Preparation are including of drying, weighing the total dry, sieving and crushing. Analysis of 137 Cs content was done using multi channel analyzer (MCA) that connected to high purity germanium (HPGe), at 661 keV, and the minimum counting time of 16 hours. To estimate the erosion/deposit rate, two mathematical model were used, namely Proportional Model (PM) and Mass Balance Model 1 (MBM1). The result for application of 137 Cs technique showed that MBM1 gives somewhat higher value for deposit rate and somewhat lower value for erosion than PM. Land use - I (LU-I) of Bojong - Ciawi was suffering from erosion with the erosion rate from 1 t/(ha.y) to 13 t/(ha.y), and LU-II has deposit rate from 1 t/(ha.y) to 50 t/(ha.y). (author)

A Quantitative Method for Long-Term Water Erosion Impacts on Productivity with a Lack of Field Experiments: A Case Study in Huaihe Watershed, China

Directory of Open Access Journals (Sweden)

Degen Lin

2016-07-01

Full Text Available Water erosion causes reduced farmland productivity, and with a longer period of cultivation, agricultural productivity becomes increasingly vulnerable. The vulnerability of farmland productivity needs assessment due to long-term water erosion. The key to quantitative assessment is to propose a quantitative method with water loss scenarios to calculate productivity losses due to long-term water erosion. This study uses the agricultural policy environmental extender (APEX model and the global hydrological watershed unit and selects the Huaihe River watershed as a case study to describe the methodology. An erosion-variable control method considering soil and water conservation measure scenarios was used to study the relationship between long-term erosion and productivity losses and to fit with 3D surface (to come up with three elements, which are time, the cumulative amount of water erosion and productivity losses to measure long-term water erosion. Results showed that: (1 the 3D surfaces fit significantly well; fitting by the 3D surface can more accurately reflect the impact of long-term water erosion on productivity than fitting by the 2D curve (to come up with two elements, which are water erosion and productivity losses; (2 the cumulative loss surface can reflect differences in productivity loss caused by long-term water erosion.

Centennial- to millennial-scale hard rock erosion rates deduced from luminescence-depth profiles

NARCIS (Netherlands)

Sohbati, Reza; Liu, Jinfeng; Jain, Mayank; Murray, Andrew; Egholm, David; Paris, Richard; Guralnik, Benny

2018-01-01

The measurement of erosion and weathering rates in different geomorphic settings and over diverse temporal and spatial scales is fundamental to the quantification of rates and patterns of earth surface processes. A knowledge of the rates of these surface processes helps one to decipher their

Short-term transport of glyphosate with erosion in Chinese loess soil--a flume experiment.

Science.gov (United States)

Yang, Xiaomei; Wang, Fei; Bento, Célia P M; Xue, Sha; Gai, Lingtong; van Dam, Ruud; Mol, Hans; Ritsema, Coen J; Geissen, Violette

2015-04-15

Repeated applications of glyphosate may contaminate the soil and water and threaten their quality both within the environmental system and beyond it through water erosion related processes and leaching. In this study, we focused on the transport of glyphosate and its metabolite aminomethylphosphonic acid (AMPA) related to soil erosion at two slope gradients (10 and 20°), two rates of pesticide with a formulation of glyphosate (Roundup®) application (360 and 720 mg m(-2)), and a rain intensity of 1.0 mm min(-1) for 1 h on bare soil in hydraulic flumes. Runoff and erosion rate were significantly different within slope gradients (psoil at the end of the experiment decreased significantly with depth (psoil layers, respectively. The risk of contamination in deep soil and the groundwater was thus low, but 5% of the initial application did reach the 2-10 cm soil layer. The risk of contamination of surface water through runoff and sedimentation, however, can be considerable, especially in regions where rain-induced soil erosion is common. Copyright © 2015 Elsevier B.V. All rights reserved.

Effect of Impact Angle on the Erosion Rate of Coherent Granular Soil, with a Chernozemic Soil as an Example

Science.gov (United States)

Larionov, G. A.; Bushueva, O. G.; Gorobets, A. V.; Dobrovol'skaya, N. G.; Kiryukhina, Z. P.; Krasnov, S. F.; Kobylchenko Kuksina, L. V.; Litvin, L. F.; Sudnitsyn, I. I.

2018-02-01

It has been shown in experiments in a hydraulic flume with a knee-shaped bend that the rate of soil erosion more than doubles at the flow impact angles to the channel side from 0° to 50°. At higher channel bends, the experiment could not be performed because of backwater. Results of erosion by water stream approaching the sample surface at angles between 2° and 90° are reported. It has been found that the maximum erosion rate is observed at flow impact angles of about 45°, and the minimum rate at 90°. The minimum soil erosion rate is five times lower than the maximum erosion rate. This is due to the difference in the rate of free water penetration into the upper soil layer, and the impact of the hydrodynamic pressure, which is maximum at the impact angle of 90°. The penetration of water into the interaggregate space results in the breaking of bonds between aggregates, which is the main condition for the capture of particles by the flow.

Sustainable agriculture, soil management and erosion from prehistoric times to 2100

Science.gov (United States)

Vanwalleghem, Tom; Gómez, Jose Alfonso; Infante Amate, Juan; González Molina, Manuel; Fernández, David Soto; Guzmán, Gema; Vanderlinden, Karl; Laguna, Ana; Giráldez, Juan Vicente

2015-04-01

The rational use of soil requires the selection of management practices to take profit of the beneficial functions of plant growth, water and nutrient storage, and pollutants removal by filtering and decomposition without altering its properties. However, the first evidence of important and widespread erosion peaks can generally be found with the arrival of the first farmers all over the world. In areas with a long land-use history such as the Mediterranean, clear signs indicating the advanced degradation status of the landscape, such as heavily truncated soils, are visible throughout. Soil conservation practices are then aimed at reducing erosion to geological rates, in equilibrium with long-term soil formation rates, while maximizing agricultural production. The adoption of such practices in most areas of the world are as old as the earliest soil erosion episodes themselves. This work firstly reviews historical evidence linking soil management and soil erosion intensity, with examples from N Europe and the Mediterranean. In particular, work by the authors in olive orchards will be presented that shows how significant variations in soil erosion rates between could be linked to the historical soil management. The potential of historical documents for calibrating a soil erosion model is shown as the model, in this case RUSLE-based and combining tillage and water erosion, adequately represents the measured erosion rate dynamics. Secondly, results from present-day, long-term farm experiments in the EU are reviewed to evaluate the effect of different soil management practices on physical soil properties, such as bulk density, penetration resistance, aggregate stability, runoff coefficient or sediment yield. Finally, we reflect upon model and field data that indicate how future global climate change is expected to affect soil management and erosion and how the examples used above hold clues about sustainable historical management practices that can be used successfully

Estimating the erosion and deposition rates in a small watershed by the {sup 137}Cs tracing method

Energy Technology Data Exchange (ETDEWEB)

Li Mian [Yellow River Institute of Hydraulic Research, Key Laboratory of Sediment Research of Yellow River of Ministry of Water Resources, Zhengzhou, Henan 450003 (China)], E-mail: hnli-mian@163.com; Li Zhanbin [Xi' an University of Technology, Xi' an, Shaanxi 710048 (China); Institute of Soil and Water Conservation, Chinese Academy of Sciences and Ministry of Water Resources, Yangling, Shaanxi 712100 (China); Yao Wenyi [Yellow River Institute of Hydraulic Research, Key Laboratory of Sediment Research of Yellow River of Ministry of Water Resources, Zhengzhou, Henan 450003 (China); Liu Puling [Institute of Soil and Water Conservation, Chinese Academy of Sciences and Ministry of Water Resources, Yangling, Shaanxi 712100 (China)

2009-02-15

Understanding the erosion and deposition rates in a small watershed is important for designing soil and water conservation measures. The objective of this study is to estimate the net soil loss and gain at points with various land use types and landform positions in a small watershed in the Sichuan Hilly Basin of China by the {sup 137}Cs tracing technique. Among various land use types, the order of erosion rate was bare rock > sloping cultivated land > forest land. The paddy field and Caotu (a kind of cultivated land located at the foot of hills) were depositional areas. The erosion rate under different landform was in this order: hillside > saddle > hilltop. The footslope and the valley were depositional areas. The {sup 137}Cs technique was shown to provide an effective means of documenting the spatial distribution of soil erosion and deposition within the small watershed.

Erosion testing of hard materials and coatings

Energy Technology Data Exchange (ETDEWEB)

Hawk, Jeffrey A.

2005-04-29

Erosion is the process by which unconstrained particles, usually hard, impact a surface, creating damage that leads to material removal and component failure. These particles are usually very small and entrained in fluid of some type, typically air. The damage that occurs as a result of erosion depends on the size of the particles, their physical characteristics, the velocity of the particle/fluid stream, and their angle of impact on the surface of interest. This talk will discuss the basics of jet erosion testing of hard materials, composites and coatings. The standard test methods will be discussed as well as alternative approaches to determining the erosion rate of materials. The damage that occurs will be characterized in genera1 terms, and examples will be presented for the erosion behavior of hard materials and coatings (both thick and thin).

Erosion of buffer caused by groundwater leakages

International Nuclear Information System (INIS)

Autio, J.; Hanana, K.; Punkkinen, O.; Koskinen, K.; Olin, M.

2010-01-01

at a total mass of 1-10 g per litre of accumulated water flow. The erosion rates were observed to depend on several different parameters such as salinity, flow rate, length of flow path and type of bentonite and, therefore, the present results, which are based on limited types of bentonite, flow rates and salinities, are regarded as preliminary only. Erosion test have been carried out to simulate the erosion with different types of experimental set-ups using different flow rates and salinities. The actual flow rate, Q(t), depends on the opening of the flow channel, pressure difference between inlet and outlet together with the length of the flow channel. The complete phenomenological modelling of these subtle phenomena is going on and it will probably take few years before those results can be used directly for erosion modelling. The mass of the eroded material within a channel was estimated in the first phase of work using a 1-D erosion model. In this model the mass of eroded material was considered in terms of concentration of eroded solids, c, in a predefined volume of fluid. The change of concentration in time is considered to depend on advection of solids to and from the volume in question by fluid flow, change of radius, R(z,t), entrainment of material and gravitational settling. Entrainment, σ(z,t) is modelled using a power law function combined with a Heaviside step function to reflect threshold shear stress for the onset of entrainment. In the current version the gravity term, G(z,t), lumps various effects like buoyancy, Soret and Magnus effects. The results of work imply that the physical and theoretical model developed can simulate the clear dependency of erosion rate on flow rate, salinity and time. (authors)

Nutrient and Organic Carbon Losses, Enrichment Rate, and Cost of Water Erosion

Directory of Open Access Journals (Sweden)

Ildegardis Bertol

Full Text Available ABSTRACT Soil erosion from water causes loss of nutrients and organic carbon, enriches the environment outside the erosion site, and results in costs. The no-tillage system generates increased nutrient and C content in the topsoil and, although it controls erosion, it can produce a more enriched runoff than in the conventional tillage system. This study was conducted in a Humic Cambisol in natural rainfall from 1997 to 2012 to quantify the contents and total losses of nutrients and organic C in soil runoff, and to calculate the enrichment rates and the cost of these losses. The treatments evaluated were: a soil with a crop, consisting of conventional tillage with one plowing + two harrowings (CT, minimum tillage with one chisel plowing + one harrowing (MT, and no tillage (NT; and b bare soil: one plowing + two harrowings (BS. In CT, MT, and NT, black oat, soybean, vetch, corn, turnip, and black beans were cultivated. Over the 15 years, 15.5 Mg ha-1 of limestone, 525 kg ha-1 of N (urea, 1,302 kg ha-1 of P2O5 (triple superphosphate, and 1,075 kg ha-1 of K2O (potassium chloride were used in the soil. The P, K, Ca, Mg, and organic C contents in the soil were determined and also the P, K, Ca, and Mg sediments in the runoff water. From these contents, the total losses, the enrichment rates (ER, and financial losses were calculated. The NT increased the P, K, and organic C contents in the topsoil. The nutrients and organic C content in the runoff from NT was greater than from CT, showing that NT was not a fully conservationist practice for soil. The linear model y = a + bx fit the data within the level of significance (p≤0.01 when the values of P, K, and organic C in the sediments from erosion were related to those values in the soil surface layer. The nutrient and organic C contents were higher in the sediments from erosion than in the soil where the erosion originated, generating values of ER>1 for P, K, and organic C. The value of the total losses

Developing an Erosion Rate Map for Myanmar Using USLE, GIS and Remote Sensing

Science.gov (United States)

Emtehani, Sobhan; Rutten, Martine

2017-04-01

Predicting erosion and estimating sediment loads in rivers are of major tasks in water resources system planning and management. In Myanmar erosion and collapse of river banks is common during the rainy season and riverine communities are frequently forced to relocate as their homes are dangerously close to the disintegrating river banks (Mann 2013). Myanmar is one of climatically most diverse countries located in Southeast Asia, where sheet, rill, and gully erosion affect crop yields as well as livelihood strategies of many people (Htwe, Brinkmann et al. 2015). In Myanmar, soil erosion measurement and monitoring approaches are increasingly important for land management planning to effectively avoid erosion and soil degradation, but such monitoring is limited by the availability of data and budgetary constraints. Therefore, spatial modeling approaches using GIS and remote sensing techniques play an important role for rapid risk assessments (Htwe 2016). In this study ''Model Builder'' tool in ArcGIS was used to create a model which generates an erosion rate map using Universal Soil Loss Equation (USLE). USLE is the product of five factors: rainfall erosivity factor (R), soil erodibility factor (K), slope length and steepness factor (LS), crop management factor (C), and support practice factor (P). Input data files for this model were acquired from online open source databases. Precipitation data was downloaded from Tropical Rainfall Measuring Mission (TRMM) for calculation of R factor. The resolution of TRMM data is very coarse (0.25 degree × 0.25 degree), therefore it was spatially downscaled by developing a relation between TRMM and Normalized Difference Vegetation Index (NDVI) using regression analysis method. Soil maps depicting percentages of sand, clay and silt were obtained from soilgrids website for calculation of K factor. Digital Elevation Model (DEM) with resolution of 90 meters was taken from Shuttle Radar Topography Mission (SRTM) for calculation of LS

Soil erosion rates caused by wind and saltating sand stresses in a wind tunnel

International Nuclear Information System (INIS)

Ligotke, M.W.

1993-02-01

Wind erosion tests were performed in a wind tunnel in support of the development of long-term protective barriers to cap stabilized waste sites at the Hanford Site. Controlled wind and saltating sand erosive stresses were applied to physical models of barrier surface layers to simulate worst-case eolian erosive stresses. The goal of these tests was to provide information useful to the design and evaluation of the surface layer composition of an arid-region waste site barrier concept that incorporates a deep fine-soil reservoir. A surface layer composition is needed that will form an armor resistant to eolian erosion during periods of extreme dry climatic conditions, especially when such conditions result in the elimination or reduction of vegetation by water deprivation or wildfire. Because of the life span required of Hanford waste barriers, it is important that additional work follow these wind tunnel studies. A modeling effort is planned to aid the interpretation of test results with respect to the suitability of pea gravel to protect the finite-soil reservoir during long periods of climatic stress. It is additionally recommended that wind tunnel tests be continued and field data be obtained at prototype or actual barrier sites. Results wig contribute to barrier design efforts and provide confidence in the design of long-term waste site caps for and regions

Erosion-corrosion synergistics in the low erosion regime

International Nuclear Information System (INIS)

Corey, R.G.; Sethi, V.K.

1986-01-01

Many engineering alloys display good high temperature corrosion resistance. However, when they are used in corrosive environments where they are subjected to erosion also, the corrosion resistance has been adversely affected. The phenomenon known as erosion-corrosion is complex and requires detailed investigation of how the erosion and corrosion kinetics interact and compete. At the Kentucky Center for Energy Research Laboratory, an erosion-corrosion tester was used to perform erosion-oxidation tests on 2 1/4 Cr-1 Mo steel at 500-600 0 C using alumina abrasive at low velocities. The erosion-oxidation rate data and morphology of exposed surfaces are consistent with oxide chipping and fracturing being the mode of material loss

Review of erosion dynamics along the major N-S climatic gradient in Chile and perspectives

Science.gov (United States)

Carretier, S.; Tolorza, V.; Regard, V.; Aguilar, G.; Bermúdez, M. A.; Martinod, J.; Guyot, J.-L.; Hérail, G.; Riquelme, R.

2018-01-01

Chile is an elongated country, running in a north-south direction for more than 30° along a subduction zone. Its climate is progressively wetter and colder from north to south. This particular geography has been used positively by a growing number of studies to better understand the relationships between erosion processes and climate, land use, slope, tectonics, volcanism, etc. Here we review the erosion rates, factors, and dynamics over millennial to daily periods reported in the literature. In addition, 21 new catchment mean erosion rates (suspended sediment and 10Be) are provided, and previous suspended sediment-derived erosion rates are updated. A total of 485 local and catchment mean erosion rates are reported. Erosion rates vary between some of the smallest values on earth (10-5 mm/a) to moderate values ≤0.5 mm/a compared to other active ranges. This review highlights strong limitations concerning the quantification of local erosion factors because of uncertainties in sampling point location, slope and rainfall data. For the mean erosion rates E for the millennial and decennial catchments, a model of the form E ∝ S/ [1 - (S/0.6)2] Rα with α = [0.3,0.8] accounts for 40 to 70% of the erosion variance, confirming a primary role of slope S compared to precipitation rate R over this time scale. Over the long-term, this review points to the long (5 to >10 Ma) response time of rivers to surface uplift in north-central arid Chile. Over millennia, data provide evidence for the progressive contribution of extreme erosion events to millennial averages for drier climates, as well as the link between glacier erosion and glacier sliding velocity. In this period of time, a discrepancy exists between the long-term offshore sedimentological record and continental decennial or millennial erosion data, for which no single explanation appears. Still, little information is available concerning the magnitude of variation of millennial erosion rates. Over centuries, data

Long-term background denudation rates of southern and southeastern Brazilian watersheds estimated with cosmogenic 10Be

Science.gov (United States)

Sosa Gonzalez, Veronica; Bierman, Paul R.; Fernandes, Nelson F.; Rood, Dylan H.

2016-09-01

In comparison to humid temperate regions of the Northern Hemisphere, less is known about the long-term (millennial scale) background rates of erosion in Southern Hemisphere tropical watersheds. In order to better understand the rate at which watersheds in southern and southeastern Brazil erode, and the relationship of that erosion to climate and landscape characteristics, we made new measurements of in situ produced 10Be in river sediments and we compiled all extant measurements from this part of the country. New data from 14 watersheds in the states of Santa Catarina (n = 7) and Rio de Janeiro (n = 7) show that erosion rates vary there from 13 to 90 m/My (mean = 32 m/My; median = 23 m/My) and that the difference between erosion rates of basins we sampled in the two states is not significant. Sampled basin area ranges between 3 and 14,987 km2, mean basin elevation between 235 and 1606 m, and mean basin slope between 11 and 29°. Basins sampled in Rio de Janeiro, including three that drain the Serra do Mar escarpment, have an average basin slope of 19°, whereas the average slope for the Santa Catarina basins is 14°. Mean basin slope (R2 = 0.73) and annual precipitation (R2 = 0.57) are most strongly correlated with erosion in the basins we studied. At three sites where we sampled river sand and cobbles, the 10Be concentration in river sand was greater than in the cobbles, suggesting that these grain sizes are sourced from different parts of the landscape. Compiling all cosmogenic 10Be-derived erosion rates previously published for southern and southeastern Brazil watersheds to date (n = 76) with our 14 sampled basins, we find that regional erosion rates (though low) are higher than those of watersheds also located on other passive margins including Namibia and the southeastern North America. Brazilian basins erode at a pace similar to escarpments in southeastern North America. Erosion rates in southern and southeastern Brazil are directly and positively related to

Numerical simulation of mud erosion rate in sand-mud alternate layer and comparison with experiment

Science.gov (United States)

Yoshida, T.; Yamaguchi, T.; Oyama, H.; Sato, T.

2015-12-01

For gas production from methane hydrates in sand-mud alternate layers, depressurization method is expected as feasible. After methane hydrate is dissociated, gas and water flow in pore space. There is a concern about the erosion of mud surface and it may result in flow blockage that disturbs the gas production. As a part of a Japanese National hydrate research program (MH21, funded by METI), we developed a numerical simulation of water-induced mud erosion in pore-scale sand-mud domains to model such mud erosion. The size of which is of the order of 100 micro meter. Water flow is simulated using a lattice Boltzmann method (LBM) and mud surface is treated as solid boundary with arbitrary shape, which changes with time. Periodic boundary condition is adopted at the domain boundaries, except for the surface of mud layers and the upper side. Shear stress acting on the mud surface is calculated using a momentum-exchange method. Mud layer is eroded when the shear stress exceeds a threshold coined a critical shear stress. In this study, we compared the simulated mud erosion rate with experimental data acquired from an experiment using artificial sand-mud core. As a result, the simulated erosion rate agrees well with that of the experiment.

EVALUATION OF SOIL EROSION IN REGHIN HILLS USING THE USLE METHOD

Directory of Open Access Journals (Sweden)

J. SZILAGYI

2016-03-01

Full Text Available Soil erosion is one of the main causes of degradation of large areas of agricultural land, causing great economic loss by removing fertile soil. The Universal Soil Loss Equation (USLE predicts the long term average annual rate of erosion on a field slope based on rainfall pattern, soil type, topography, crop system and management practices but does not however predict the soil loss resulting from gully erosion.

Constraints on Water Reservoir Lifetimes From Catchment-Wide 10Be Erosion Rates—A Case Study From Western Turkey

Science.gov (United States)

Heineke, Caroline; Hetzel, Ralf; Akal, Cüneyt; Christl, Marcus

2017-11-01

The functionality and retention capacity of water reservoirs is generally impaired by upstream erosion and reservoir sedimentation, making a reliable assessment of erosion indispensable to estimate reservoir lifetimes. Widely used river gauging methods may underestimate sediment yield, because they do not record rare, high-magnitude events and may underestimate bed load transport. Hence, reservoir lifetimes calculated from short-term erosion rates should be regarded as maximum values. We propose that erosion rates from cosmogenic 10Be, which commonly integrate over hundreds to thousands of years, are useful to complement short-term sediment yield estimates and should be employed to estimate minimum reservoir lifetimes. Here we present 10Be erosion rates for the drainage basins of six water reservoirs in Western Turkey, which are located in a tectonically active region with easily erodible bedrock. Our 10Be erosion rates for these catchments are high, ranging from ˜170 to ˜1,040 t/km2/yr. When linked to reservoir volumes, they yield minimum reservoir lifetimes between 25 ± 5 and 1,650 ± 360 years until complete filling, with four reservoirs having minimum lifespans of ≤110 years. In a neighboring region with more resistant bedrock and less tectonic activity, we obtain much lower catchment-wide 10Be erosion rates of ˜33 to ˜95 t/km2/yr, illustrating that differences in lithology and tectonic boundary conditions can cause substantial variations in erosion even at a spatial scale of only ˜50 km. In conclusion, we suggest that both short-term sediment yield estimates and 10Be erosion rates should be employed to predict the lifetimes of reservoirs.

Estimation of water erosion rates using RUSLE3D in Alicante province (Spain)

OpenAIRE

Garcia Rodríguez, Jose Luis; Giménez Suárez, Martín Cruz; Arraiza Bermudez-Cañete, Maria Paz

2015-01-01

The purpose of this study was the estimation of current and potential water erosion rates in Alicante Province using RUSLE3D (Revised Universal Soil Loss Equation-3D) model with Geographical Information System (GIS) support by request from the Valencia Waste Energy Use. RUSLE3D uses a new methodology for topographic factor estimation (LS factor) based on the impact of flow convergence allowing better assessment of sediment distribution detached by water erosion. In RUSLE3D equation, the effec...

Understanding erosion rates in the Himalayan orogen: A case study from the Arun Valley

Science.gov (United States)

Olen, Stephanie M.; Bookhagen, Bodo; Hoffmann, Bernd; Sachse, Dirk; Adhikari, D. P.; Strecker, Manfred R.

2015-10-01

Understanding the rates and pattern of erosion is a key aspect of deciphering the impacts of climate and tectonics on landscape evolution. Denudation rates derived from terrestrial cosmogenic nuclides (TCNs) are commonly used to quantify erosion and bridge tectonic (Myr) and climatic (up to several kiloyears) time scales. However, how the processes of erosion in active orogens are ultimately reflected in 10Be TCN samples remains a topic of discussion. We investigate this problem in the Arun Valley of eastern Nepal with 34 new 10Be-derived catchment-mean denudation rates. The Arun Valley is characterized by steep north-south gradients in topography and climate. Locally, denudation rates increase northward, from <0.2 mm yr-1 to ~1.5 mm yr-1 in tributary samples, while main stem samples appear to increase downstream from ~0.2 mm yr-1 at the border with Tibet to 0.91 mm yr-1 in the foreland. Denudation rates most strongly correlate with normalized channel steepness (R2 = 0.67), which has been commonly interpreted to indicate tectonic activity. Significant downstream decrease of 10Be concentration in the main stem Arun suggests that upstream sediment grains are fining to the point that they are operationally excluded from the processed sample. This results in 10Be concentrations and denudation rates that do not uniformly represent the upstream catchment area. We observe strong impacts on 10Be concentrations from local, nonfluvial geomorphic processes, such as glaciation and landsliding coinciding with areas of peak rainfall rates, pointing toward climatic modulation of predominantly tectonically driven denudation rates.

Influence of liquid temperature and flow rate on enamel erosion and surface softening.

Science.gov (United States)

Eisenburger, M; Addy, M

2003-11-01

Enamel erosion and softening are based on chemical processes which could be influenced by many factors including temperature and acid flow rate. Knowledge of the influence of these variables could have relevance to research experiments and clinical outcomes. Both parameters were investigated using an ultrasonication and profilometry method to assess erosion depth and surface softening of enamel. The influence of temperature was studied by eroding polished human enamel samples at 4, 20, 35 or 50 degrees C for 2 h. Secondly, different liquid flow conditions were established by varying acid agitation. Additionally, a slow laminar flow and a jet of citric acid, to simulate drinking through a straw, were applied to specimens. Erosion depth increased significantly with acid temperature from 11.0 microm at 4 degrees C to 35.8 microm at 50 degrees C. Surface softening increased much more slowly and plateaued at 2.9 microm to 3.5 microm after 35 degrees C. A strong dependence of erosion on liquid flow was revealed. In unstirred conditions only 8.6 microm erosion occurred, which increased to 22.2 microm with slow stirring and 40.9 microm with fast stirring. Surface softening did not increase correspondingly with its largest extent at slow stirring at 3.4 microm.The implication of these data are: first, the conditions for erosion experiments in vitro or in situ need to be specified for reliable comparisons between studies. Secondly, erosion of teeth by soft drinks are likely to be influenced both by the temperature of the drink and individual drinking habits.

Ultrasonic Measurement of Erosion/corrosion Rates in Industrial Piping Systems

Science.gov (United States)

Sinclair, A. N.; Safavi, V.; Honarvar, F.

2011-06-01

Industrial piping systems that carry aggressive corrosion or erosion agents may suffer from a gradual wall thickness reduction that eventually threatens pipe integrity. Thinning rates could be estimated from the very small change in wall thickness values measured by conventional ultrasound over a time span of at least a few months. However, measurements performed over shorter time spans would yield no useful information—minor signal distortions originating from grain noise and ultrasonic equipment imperfections prevent a meaningful estimate of the minuscule reduction in echo travel time. Using a Model-Based Estimation (MBE) technique, a signal processing scheme has been developed that enables the echo signals from the pipe wall to be separated from the noise. This was implemented in a laboratory experimental program, featuring accelerated erosion/corrosion on the inner wall of a test pipe. The result was a reduction in the uncertainty in the wall thinning rate by a factor of four. This improvement enables a more rapid response by system operators to a change in plant conditions that could pose a pipe integrity problem. It also enables a rapid evaluation of the effectiveness of new corrosion inhibiting agents under plant operating conditions.

Volumetric measurement of river bank erosion from sequential historical aerial photography

Science.gov (United States)

Spiekermann, Raphael; Betts, Harley; Dymond, John; Basher, Les

2017-11-01

Understanding of the relative contribution of bank erosion to sediment budgets in New Zealand is limited. Few measurements of bank erosion rates exist, and this is a major limitation to the development of a locally calibrated model of bank erosion. The New Zealand sediment budget model, SedNetNZ, predicts bank erosion based on preliminary data, and this study aims to underpin the development of an improved model for bank erosion. Photogrammetric techniques and LiDAR were used to collect data on bank erosion rates for five different river reaches, ranging from 3 to 14 km in length, in the Kaipara Catchment, Northland, New Zealand. Changing river channel planform between the 1950s and 2015 was assessed using four to five well-spaced dates of historical aerial photographs. Changes in planform were combined with bank height, to calculate erosion and accretion volumes which were compared with SedNetNZ modelled estimates. Erosion and accretion is relatively evenly balanced in the study sites. The largest difference in terms of relative proportions of erosion and accretion are found along the Tangowahine River (13.4 km reach length), where 492,000 m3 of sediment eroded between 1956 and 2015 compared to 364,000 m3 of accretion. Lateral migration rates (erosion) for the five river reaches range between 0.14 m yr- 1 and 0.21 m yr- 1 and are comparable with those measured by previous assessments in New Zealand. The migration rates in channel widths per year for the three larger rivers (stream order 5-6) range between 0.4% and 0.8% of channel width per year. In contrast, the smaller streams (stream order 3-4) are retreating more rapidly, with width-averaged rates of 1.7% and 3.0%. Current SedNetNZ modelling tends to underestimate the bank height and greatly overestimates the migration rate.

Erosion Associated with Seismically-Induced Landslides in the Middle Longmen Shan Region, Eastern Tibetan Plateau, China

Directory of Open Access Journals (Sweden)

Zhikun Ren

2017-08-01

Full Text Available The 2008 Wenchuan earthquake and associated co-seismic landslide was the most recent expression of the rapid deformation and erosion occurring in the eastern Tibetan Plateau. The erosion associated with co-seismic landslides balances the long-term tectonic uplift in the topographic evolution of the region; however, the quantitative relationship between earthquakes, uplift, and erosion is still unknown. In order to quantitatively distinguish the seismically-induced erosion in the total erosion, here, we quantify the Wenchuan earthquake-induced erosion using the digital elevation model (DEM differential method and previously-reported landslide volumes. Our results show that the seismically-induced erosion is comparable with the pre-earthquake short-term erosion. The seismically-induced erosion rate contributes ~50% of the total erosion rate, which suggests that the local topographic evolution of the middle Longmen Shan region may be closely related to tectonic events, such as the 2008 Wenchuan earthquake. We propose that seismically-induced erosion is a very important component of the total erosion, particularly in active orogenic regions. Our results demonstrate that the remote sensing technique of differential DEM provides a powerful tool for evaluating the volume of co-seismic landslides produced in intermountain regions by strong earthquakes.

Quantifying Soil Erosion and Deposition Rates in Tea Plantation Area, Cameron Highlands, Malaysia Using 137Cs

International Nuclear Information System (INIS)

Zaini Hamzah; Che Yasmin Amirudin; Ahmad Saat; Ahmad Saat; Ab Khalik Wood

2014-01-01

The soil erosion and deposition in the hilly area is a great concern for the planters. In this study, the tea plantation was chosen to quantify the rates of soil erosion and deposition for it will provide information on the improvement of soil conditions and cost reduction of fertilizer consumption. The aims of this research are to determine the rate of soil erosion and deposition using environmental radionuclide, 137 Cs. Soil profile samples were collected by using scrapper plate and two cores soil sample were collected in the undisturbed forests area nearby. The 137 Cs activity concentration was measured using low background coaxial hyper pure germanium detector gamma spectrometer based on 137 Cs gamma energy peak at 661.66 keV. The highest erosion rate using Proportional Models and Mass Balance Model 1 was found in point HE top area which is 52.39 t ha -1 yr -1 and 95.53 t ha -1 yr -1 respectively while the lowest at location HF top which is 4.78 t ha -1 yr -1 and 4.97 t ha -1 yr -1 . The deposition rate was higher in HF center which is 216.82 t ha -1 yr -1 and 97.51 t ha -1 yr -1 and the lowest at HE center which is 0.05 t ha -1 yr -1 for both models used. (author)

The Influence of Cultivation System on Distribution Profile Of 137cs and Erosion / Deposition Rate

Directory of Open Access Journals (Sweden)

Nita Suhartini

2016-05-01

Full Text Available 137Cs radiogenic content in the soil can be used to estimate the rate of erosion and deposition in an area occurring since 1950’s, by comparing the content of the 137Cs in observed site with those in a stable reference site. This experiment aimed to investigate the influence of cultivation type on distribution profile of 137Cs and distribution of erosion and deposition rate in cultivated area. A study site was small cultivated area with slope steepness <10o and length 2 km located in Bojong – Ciawi. For this purpose, the top of a slope was chosen for reference site and three plot sites were selected namely Land Use I that using simple cultivation, Land Use II that using simple cultivation with ridge and furrow, and Land Use III using machine cultivation. The results showed that cultivation could make a movement of 137Cs to the deeper layer and ridges and furrows cultivation system could minimized an erosion process. The net erosion and deposition for land Use I, II and III were -25 t/ha/yr , 24 t/ha/yr and -58 t/ha/yr, respectively.

Native Roadside Vegetation that Enhances Soil Erosion Control in Boreal Scandinavia

Directory of Open Access Journals (Sweden)

Annika K. Jägerbrand

2014-07-01

Full Text Available This study focused on identifying vegetation characteristics associated with erosion control at nine roadside sites in mid-West Sweden. A number of vegetation characteristics such as cover, diversity, plant functional type, biomass and plant community structure were included. Significant difference in cover between eroded and non-eroded sub-sites was found in evergreen shrubs, total cover, and total above ground biomass. Thus, our results support the use of shrubs in order to stabilize vegetation and minimize erosion along roadsides. However, shrubs are disfavored by several natural and human imposed factors. This could have several impacts on the long-term management of roadsides in boreal regions. By both choosing and applying active management that supports native evergreen shrubs in boreal regions, several positive effects could be achieved along roadsides, such as lower erosion rate and secured long-term vegetation cover. This could also lead to lower costs for roadside maintenance as lower erosion rates would require less frequent stabilizing treatments and mowing could be kept to a minimum in order not to disfavor shrubs.

The National Wind Erosion Research Network: Building a standardized long-term data resource for aeolian research, modeling and land management

Science.gov (United States)

Webb, Nicholas P.; Herrick, Jeffrey E.; Van Zee, Justin W; Courtright, Ericha M; Hugenholtz, Ted M; Zobeck, Ted M; Okin, Gregory S.; Barchyn, Thomas E; Billings, Benjamin J; Boyd, Robert A.; Clingan, Scott D; Cooper, Brad F; Duniway, Michael C.; Derner, Justin D.; Fox, Fred A; Havstad, Kris M.; Heilman, Philip; LaPlante, Valerie; Ludwig, Noel A; Metz, Loretta J; Nearing, Mark A; Norfleet, M Lee; Pierson, Frederick B; Sanderson, Matt A; Sharrat, Brenton S; Steiner, Jean L; Tatarko, John; Tedela, Negussie H; Todelo, David; Unnasch, Robert S; Van Pelt, R Scott; Wagner, Larry

2016-01-01

The National Wind Erosion Research Network was established in 2014 as a collaborative effort led by the United States Department of Agriculture’s Agricultural Research Service and Natural Resources Conservation Service, and the United States Department of the Interior’s Bureau of Land Management, to address the need for a long-term research program to meet critical challenges in wind erosion research and management in the United States. The Network has three aims: (1) provide data to support understanding of basic aeolian processes across land use types, land cover types, and management practices, (2) support development and application of models to assess wind erosion and dust emission and their impacts on human and environmental systems, and (3) encourage collaboration among the aeolian research community and resource managers for the transfer of wind erosion technologies. The Network currently consists of thirteen intensively instrumented sites providing measurements of aeolian sediment transport rates, meteorological conditions, and soil and vegetation properties that influence wind erosion. Network sites are located across rangelands, croplands, and deserts of the western US. In support of Network activities, http://winderosionnetwork.org was developed as a portal for information about the Network, providing site descriptions, measurement protocols, and data visualization tools to facilitate collaboration with scientists and managers interested in the Network and accessing Network products. The Network provides a mechanism for engaging national and international partners in a wind erosion research program that addresses the need for improved understanding and prediction of aeolian processes across complex and diverse land use types and management practices.

In situ estimation of erosion and deposition thresholds by Acoustic Doppler Velocimeter (ADV)

DEFF Research Database (Denmark)

Andersen, T.J.; Fredsøe, Jørgen; Pejrup, M.

2007-01-01

Field-based estimations of bed shear stress have been made using SonTek/YSI 10 MHz ADVs (Acoustic Doppler Velocimeter) at the Kongsmark mudflat, Danish Wadden Sea, in order to test if it was possible to estimate erosion and deposition thresholds in situ by use of unidirectional tidal and orbital...... (wave) currents. The results were promising and erosion thresholds were in the same range as those observed in EROMES erosion experiments carried out at the same site. Similarly, the short-term erosion rates which could be calculated matched closely those obtained with EROMES, and were in the same range...... as those published for a large annular flume (Sea Carousel) from another fine-grained site. This indicates that the erosion rates obtained with those two erosion-instruments are reasonable estimates of the actual erosion taking place under natural tidal current and waves. One advantage of the use of ADVs...

Small crater modification on Meridiani Planum and implications for erosion rates and climate change on Mars

Science.gov (United States)

Golombek, M.P.; Warner, N.H.; Ganti, V.; Lamb, M.P.; Parker, T.J.; Fergason, Robin L.; Sullivan, R.

2014-01-01

A morphometric and morphologic catalog of ~100 small craters imaged by the Opportunity rover over the 33.5 km traverse between Eagle and Endeavour craters on Meridiani Planum shows craters in six stages of degradation that range from fresh and blocky to eroded and shallow depressions ringed by planed off rim blocks. The age of each morphologic class from Mars over ~100 Myr and 3 Gyr timescales from the Amazonian and Hesperian are of order <0.01 m/Myr, which is 3–4 orders of magnitude slower than typical terrestrial rates. Erosion rates during the Middle-Late Noachian averaged over ~250 Myr, and ~700 Myr intervals are around 1 m/Myr, comparable to slow terrestrial erosion rates calculated over similar timescales. This argues for a wet climate before ~3 Ga in which liquid water was the erosional agent, followed by a dry environment dominated by slow eolian erosion.

Application of the 137Cs determination to evaluate the erosion rates in cultivated soils in the west part of Cuba

International Nuclear Information System (INIS)

Gil Castillo, Reinaldo; Peralta Vital, Jose Luis; Carrazana Gonzalez, Jorge; Riverol Rosquet, Mario; Penna Valenti, Fermin; Cabrera Calcedo, Eduardo

2004-01-01

The paper shows the experience in the application of 137Cs technique to estimate the erosion rates in cultivated soils (Ultisol) in the west part of the country, and the validation of the technique results by comparison against the results from traditional methods (watershed segments). The proportional, the simplified balance of mass and the balance of mass models were used to calculate the erosion rates, for three segments. In the evaluated area, have been obtained erosion rates from 3.5 to 7.1 t/ha/y for the segment I, from 5.17 to 10.3 t/ha/y for the segment III and from 2.3 to 17 t/ha/y for the segment IX. The conclusions are, the 137Cs technique is reliable for the estimation of erosion rates in the evaluated soil and the mass balance model obtained the nearest values to the estimated by watershed segments

Regional shoreline change and coastal erosion hazards in Arctic Alaska

Science.gov (United States)

Gibbs, Ann E.; Richmond, Bruce M.; Erikson, Li H.; Harden, E. Lynne; Wallendorf, Louise

2011-01-01

Historical shoreline positions along the mainland Beaufort Sea coast of Alaska were digitized and analyzed to determine the long-term rate of change. Average shoreline change rates and ranges from 1947 to the mid-2000s were determined every 50 meters between Barrow and Demarcation Point, at the U.S.-Canadian border. Results show that shoreline change rates are highly variable along the coast, with an average regional shoreline change rate of-2.0 m/yr and localized rates of up to -19 m/yr. The highest erosion rates were observed at headlands, points, and associated with breached thermokarst lakes. Areas of accretion were limited, and generally associated with spit extension and minor beach accretion. In general, erosion rates increase from east to west, with overall higher rates east of Harrison Bay.

Contributions of solar-wind induced potential sputtering to the lunar surface erosion rate and it's exosphere

Science.gov (United States)

Alnussirat, S. T.; Barghouty, A. F.; Edmunson, J. E.; Sabra, M. S.; Rickman, D. L.

2018-04-01

Sputtering of lunar regolith by solar-wind protons and heavy ions with kinetic energies of about 1 keV/amu is an important erosive process that affects the lunar surface and exosphere. It plays an important role in changing the chemical composition and thickness of the surface layer, and in introducing material into the exosphere. Kinetic sputtering is well modeled and understood, but understanding of mechanisms of potential sputtering has lagged behind. In this study we differentiate the contributions of potential sputtering from the standard (kinetic) sputtering in changing the chemical composition and erosion rate of the lunar surface. Also we study the contribution of potential sputtering in developing the lunar exosphere. Our results show that potential sputtering enhances the total characteristic sputtering erosion rate by about 44%, and reduces sputtering time scales by the same amount. Potential sputtering also introduces more material into the lunar exosphere.

Protection from erosion following wildfire

Science.gov (United States)

Peter R. Robichaud; William J. Elliot

2006-01-01

Erosion in the first year after a wildfire can be up to three orders of magnitude greater than the erosion from undisturbed forests. To mitigate potential postfire erosion, various erosion control treatments are applied on highly erodible areas with downstream resources in need of protection. Because postfire erosion rates generally decline by an order of magnitude for...

Coastal erosion management in Accra: Combining local knowledge and empirical research

Directory of Open Access Journals (Sweden)

Kwasi Appeaning Addo

2016-11-01

Full Text Available Coastal erosion along the Accra coast has become a chronic phenomenon that threatens both life and property. The issue has assumed a centre stage of national debate in recent times because of its impact on the coastal communities. Lack of reliable geospatial data hinders effective scientific investigations into the changing trends in the shoreline position. However, knowledge about coastal erosion, by the local people, and how far the shoreline has migrated inland over time is high in the coastal communities in Accra. This opens a new chapter in coastal erosion research to include local knowledge of the local settlers in developing sustainable coastal management. This article adopted a scientific approach to estimate rate of erosion and tested the results against perceived erosion trend by the local settlers. The study used a 1974 digital topographic map and 1996 aerial photographs. The end point rate statistical method in DSAS was used to compute the rates of change. The short-term rate of change for the 22-year period under study was estimated as -0.91 m/annum ± 0.49 m/annum. It was revealed that about 79% of the shoreline is eroding, while the remaining 21% is either stabilised or accreting. It emerged, from semi-structured interviews with inhabitants in the Accra coastal communities, that an average of about 30 m of coastal lands are perceived to have been lost to erosion for a period of about 20 years. This translates to a historic rate of change of about 1.5 m/year, which corroborates the results of the scientific study. Again this study has established that the local knowledge of the inhabitants, about coastal erosion, can serve as reliable information under scarcity of scientific data for coastal erosion analyses in developing countries.

Buffer erosion in dilute groundwater

International Nuclear Information System (INIS)

Schatz, T.; Kanerva, N.; Martikainen, J.; Sane, P.; Olin, M.; Seppaelae, A.; Koskinen, K.

2013-08-01

One scenario of interest for repository safety assessment involves the loss of bentonite buffer material in contact with dilute groundwater flowing through a transmissive fracture interface. In order to examine the extrusion/erosion behavior of bentonite buffer material under such circumstances, a series of experiments were performed in a flow-through, 1 mm aperture, artificial fracture system. These experiments covered a range of solution chemistry (salt concentration and composition), material composition (sodium montmorillonite and admixtures with calcium montmorillonite), and flow velocity conditions. No erosion was observed for sodium montmorillonite against solution compositions from 0.5 g/L to 10 g/L NaCl. No erosion was observed for 50/50 calcium/sodium montmorillonite against 0.5 g/L NaCl. Erosion was observed for both sodium montmorillonite and 50/50 calcium/sodium montmorillonite against solution compositions ≤ 0.25 g/L NaCl. The calculated erosion rates for the tests with the highest levels of measured erosion, i.e., the tests run under the most dilute conditions (ionic strength (IS) < ∼1 mM), were well-correlated to flow velocity, whereas the calculated erosion rates for the tests with lower levels of measured erosion, i.e., the tests run under somewhat less dilute conditions (∼1 mM < IS < ∼4 mM), were not similarly correlated indicating that material and solution composition can significantly affect erosion rates. In every experiment, both erosive and non-erosive, emplaced buffer material extruded into the fracture and was observed to be impermeable to water flowing in the fracture effectively forming an extended diffusive barrier around the intersecting fracture/buffer interface. Additionally, a model which was developed previously to predict the rate of erosion of bentonite buffer material in low ionic strength water in rock fracture environments was applied to three different cases: sodium montmorillonite expansion in a vertical tube, a

Divertor erosion in DIII-D

International Nuclear Information System (INIS)

Whyte, D.G.; Bastasz, R.; Wampler, W.R.; Brooks, J.N.; West, W.P.; Wong, C.P.C.

1998-05-01

Net erosion rates of carbon target plates have been measured in situ for the DIII-D lower divertor. The principal method of obtaining this data is the DiMES sample probe. Recent experiments have focused on erosion at the outer strike-point of two divertor plasma conditions: (1) attached (Te > 40 eV) ELMing plasmas and (2) detached (Te 10 cm/year, even with incident heat flux 2 . In this case, measurements and modeling agree for both gross and net carbon erosion, showing the near-surface transport and redeposition of the carbon is well understood and that effective sputtering yields are > 10%. In ELM-free discharges, this erosion rate can account for the rate of carbon accumulation in the core plasma. Divertor plasma detachment eliminates physical sputtering, while spectroscopically measured chemical erosion yields are also found to be low (Y(C/D + ) ≤ 2.0 x 10 -3 ). This leads to suppression of net erosion at the outer strike-point, which becomes a region of net redeposition (∼ 4 cm/year). The private flux wall is measured to be a region of net redeposition with dense, high neutral pressure, attached divertor plasmas. Leading edges intercepting parallel heat flux (∼ 50 MW/m 2 ) have very high net erosion rates (∼ 10 microm/s) at the OSP of an attached plasma. Leading edge erosion, and subsequent carbon redeposition, caused by tile gaps can account for half of the deuterium codeposition in the DIII-D divertor

Centennial- to millennial-scale hard rock erosion rates deduced from luminescence-depth profiles

DEFF Research Database (Denmark)

Sohbati, Reza; Liu, Jinfeng; Jain, Mayank

2018-01-01

to quantify hard rock erosion rates at centennial to millennial timescales. Here we propose a novel technique, based on the solar bleaching of luminescence signals with depth into rock surfaces, to bridge this analytical gap. We apply our technique to glacial and landslide boulders in the Eastern Pamirs...

Is Snow Gliding a Major Soil Erosion Agent in Steep Alpine Areas?

International Nuclear Information System (INIS)

Meusburger, K.; Walter, A.; Alewell, C.; Leitinger, G.; Mabit, L.; Mueller, M.H.

2015-01-01

Snow cover is a key hydrological characteristic of mountain areas. Nevertheless, a majority of studies focused on quantifying rates of soil erosion and sediment transport in steep mountain areas has largely neglected the role of snow cover on soil erosion rates (Stanchi et al., 2014). Soil erosion studies have focused almost exclusively on the snow-free periods even though it is well known that wet avalanches can yield enormous erosive forces (Freppaz et al., 2010; Korup and Rixen, 2014). This raises the question whether annual snow cover and particularly the slow movement of snow packages over the soil surface, termed ‘‘snow gliding’’, contribute significantly to the total soil loss in these areas. Three different approaches to estimate soil erosion rates were used to address this question. These include (1) the anthropogenic soil tracer 137 Cs, (2) the Revised Universal Soil Loss Equation (RUSLE), and (3) direct sediment yield measurements of snow glide deposits. The fallout radionuclide 137 Cs integrates total soil loss due to all erosion agents involved, the RUSLE model is suitable to estimate soil loss by water erosion and the sediment yield measurements yield represents a direct estimate of soil removal by snow gliding. Moreover, cumulative snow glide distance was measured for 14 sites and modelled for the surrounding area with the Spatial Snow Glide Model (Leitinger et al., 2008)

Comparison of soil erosion and deposition rates using radiocesium, RUSLE, and buried soils in dolines in East Tennessee

International Nuclear Information System (INIS)

Turnage, K.M.; Lee, S.Y.; Foss, J.E.; Kim, K.H.; Larsen, I.L.

1997-01-01

Three dolines (sinkholes), each representing different land uses (crop, grass, and forest) in a karst area in East Tennesse, were selected to determine soil erosional and depositional rates. Three methods were used to estimate the rates: fallout radiocesium ( 137 Cs) redistribution, buried surface soil horizons (Ab horizon), and the revised universal soil loss equation (RUSLE). When 137 Cs redistribution was examined, the average soil erosion rates were calculated to be 27 t ha -1 yr -1 at the cropland, 3 t ha -1 yr -1 at the grassland, and 2 t ha -1 yr -1 at the forest. By comparison, cropland erosion rate of 2.6 t ha -1 yr -1 , a grassland rate of 0.6 t ha -1 yr -1 , and a forest rate of 0.2 t ha -1 yr -1 were estimated by RUSLE. The 137 Cs method expressed higher rates than RUSLE because RUSLE tends to overestimate low erosion rates and does not account for deposition. The buried surface horizons method resulted in deposition rates that were 8 t ha -1 yr -1 (during 480 yr) at the cropland, 12 t ha -1 yr -1 (during 980 yr) at the grassland, and 4 t ha -1 yr -1 (during 101 yr) at the forest site. By examining 137 Cs redistribution, soil deposition rates were found to be 23 t ha -1 yr -1 at the cropland, 20 t ha -1 yr -1 at the grassland, and 16 t ha -1 yr -1 at the forest site. The variability in deposition rates was accounted for by temporal differences; 137 Cs expressed deposition during the last 38 yr, whereas Ab horizons represented deposition during hundreds of years. In most cases, land used affected both erosion and deposition rates - the highest rates of soil redistribution usually representing the cropland and the lowest, the forest. When this was not true, differences in the rates were attributed to differences in the size, shape, and closure of the dolines. (orig.)

Divertor erosion in DIII-D

International Nuclear Information System (INIS)

Whyte, D.G.; Bastasz, R.; Wampler, W.R.; Brooks, J.N.; West, W.P.; Wong, C.P.C.; Buzhinskij, O.I.; Opimach, I.V.

1998-08-01

Net erosion rates of carbon target plates have been measured in situ for the DIII-D lower divertor. The principal method of obtaining this data is the DiMES sample probe. Recent experiments have focused on erosion at the outer strike-point (OSP) of two divertor plasma conditions: attached (T e > 40 eV) ELMing plasmas, and detached (T e 2 . In this case, measurements and modeling agree for both gross and net carbon erosion, showing the near-surface transport and redeposition of the carbon is well understood. In the attached cases, physical sputtering (with enhancement from self-sputtering and oblique incidence) is dominant, and the effective sputtering yield, Y, is greater than 10%. In ELM-free discharges, the total OSP net erosion rate is equal to the rate of carbon accumulation in the core plasma. For the detached divertor cases, the cold incident plasma eliminates physical sputtering. Attempts to measure chemically eroded hydrocarbon molecules spectroscopically indicate an upper limit of Y ≤ 0.1% for the chemical sputtering yield. Net erosion is suppressed at the outer strike-point, which becomes a region of net redeposition (∼ 4 cm/exposure-year). The private flux wall is measured to be a region of net redeposition with dense, high neutral pressure, attached divertor plasmas. Leading edges intercepting parallel heat flux (∼ 50 MW/m 2 ) have very high net erosion rates at the OSP of an attached plasma (∼ 10 microm/s > 1,000x erosion rate of aligned surfaces). Leading edge erosion, and subsequent carbon redeposition, caused by tile gaps can account for half of the deuterium codeposition in the DIII-D divertor

Nozzle erosion characterization and minimization for high-pressure rocket motor applications

Science.gov (United States)

Evans, Brian

correlation also incorporates the RMS data, accounting for swirling flow of the products in the RMS combustor. These correlations are useful for rocket nozzle designs. The correlation for non-metallized propellant and RMS firings was developed in terms of the effective oxidizer mass fraction and effective Reynolds number. The results calculated from this correlation were compared with measured erosion rate data within +/-15% or 0.05 mm/s (2 mils/s). For metallized propellant, the nozzle erosion rate was found to be relatively independent of the concentration of oxidizing species due to the diffusion-controlled process and the partial surface coverage by the liquid Al/Al2O3 layer. The nozzle erosion rate was also found to be lower than those of non-metallized propellant cases. Agreement between predicted and measured erosion rates was found to be within +/-20% or 0.04 mm/s (2 mils/s).

Quantifying accelerated soil erosion through ecological site-based assessments of wind and water erosion

Science.gov (United States)

This work explores how organising soil erosion assessments using established groupings of similar soils (ecological sites) can inform systems for managing accelerated soil erosion. We evaluated aeolian sediment transport and fluvial erosion rates for five ecological sites in southern New Mexico, USA...

Uncertainty in soil carbon accounting due to unrecognized soil erosion.

Science.gov (United States)

Sanderman, Jonathan; Chappell, Adrian

2013-01-01

The movement of soil organic carbon (SOC) during erosion and deposition events represents a major perturbation to the terrestrial carbon cycle. Despite the recognized impact soil redistribution can have on the carbon cycle, few major carbon accounting models currently allow for soil mass flux. Here, we modified a commonly used SOC model to include a soil redistribution term and then applied it to scenarios which explore the implications of unrecognized erosion and deposition for SOC accounting. We show that models that assume a static landscape may be calibrated incorrectly as erosion of SOC is hidden within the decay constants. This implicit inclusion of erosion then limits the predictive capacity of these models when applied to sites with different soil redistribution histories. Decay constants were found to be 15-50% slower when an erosion rate of 15 t soil ha(-1)  yr(-1) was explicitly included in the SOC model calibration. Static models cannot account for SOC change resulting from agricultural management practices focused on reducing erosion rates. Without accounting for soil redistribution, a soil sampling scheme which uses a fixed depth to support model development can create large errors in actual and relative changes in SOC stocks. When modest levels of erosion were ignored, the combined uncertainty in carbon sequestration rates was 0.3-1.0 t CO2  ha(-1)  yr(-1) . This range is similar to expected sequestration rates for many management options aimed at increasing SOC levels. It is evident from these analyses that explicit recognition of soil redistribution is critical to the success of a carbon monitoring or trading scheme which seeks to credit agricultural activities. © 2012 Blackwell Publishing Ltd.

AERO: A Decision Support Tool for Wind Erosion Assessment in Rangelands and Croplands

Science.gov (United States)

Galloza, M.; Webb, N.; Herrick, J.

2015-12-01

Wind erosion is a key driver of global land degradation, with on- and off-site impacts on agricultural production, air quality, ecosystem services and climate. Measuring rates of wind erosion and dust emission across land use and land cover types is important for quantifying the impacts and identifying and testing practical management options. This process can be assisted by the application of predictive models, which can be a powerful tool for land management agencies. The Aeolian EROsion (AERO) model, a wind erosion and dust emission model interface provides access by non-expert land managers to a sophisticated wind erosion decision-support tool. AERO incorporates land surface processes and sediment transport equations from existing wind erosion models and was designed for application with available national long-term monitoring datasets (e.g. USDI BLM Assessment, Inventory and Monitoring, USDA NRCS Natural Resources Inventory) and monitoring protocols. Ongoing AERO model calibration and validation are supported by geographically diverse data on wind erosion rates and land surface conditions collected by the new National Wind Erosion Research Network. Here we present the new AERO interface, describe parameterization of the underpinning wind erosion model, and provide a summary of the model applications across agricultural lands and rangelands in the United States.

Soil erosion rates from mixed soil and gravel surfaces in a wind tunnel: A preliminary report

International Nuclear Information System (INIS)

Ligotke, M.W.

1988-12-01

Tests of wind erosion were performed in a controlled-environment wind tunnel to support the development of natural-material protective barriers for long-term isolation of radioactive waste. Barrier performance standards currently being developed for internal and external barrier performance are expected to mandate a surface layer that is resistant to wind erosion. The purpose of this study was to initiate a series of tests to determine suitable soil and gravel mixtures for such a barrier and to test worst-case surface layer conditions under the influence of high wind speeds. Six mixed soil and gravel surfaces were prepared, weathered to represent natural wind-blown desert areas, and subjected to controlled wind erosion forces in a wind tunnel. The applied erosive forces, including surface shear forces, were characterized to provide a means of relating wind tunnel results with actual field conditions. Soil particle losses from the surfaces caused by suspension, saltation, and surface creep were monitored by aerosol sample probes and mass balance measurements. 23 refs., 22 figs., 3 tabs

Soil erosion and sedimentation rates in a small eutrophic lake in southern Chile estimated by 210Pb isotope analysis

International Nuclear Information System (INIS)

Cisternas, M.; Urrutia, R.; Araneda, A.; Debels, P.; Rios, F.

1999-01-01

The purpose of this research is to study the effects of historical land use patterns on soil erosion within the San Pedro Lake watershed (Concepcion, VIII Region, Chile). To this end, a geochronological reconstruction of the last 50 years was accomplished by 210 Pb isotope and photo-interpretation analysis through the use of GIS. The erosion rate has varied from 0.40 t ha -1 y -1 in 1955 to 0.86 t ha -1 y -1 in 1994. The decrease in native forest was closely coupled with the increase in exotic forestry. The Total Change, meaning the land use change without considering each typology, shows a constant trend indicating a greater degree of anthropogenic intervention. As opposed to the expected, there is no relationship between land use typologies and erosion rates, however it is possible to recognise some degree of dependency between Total Change and erosion values. It is concluded that over the last 50 years the soil erosion processes in the San Pedro Lake watershed may have been more regulated more by land use changes than by land use typologies themselves. (author)

Determining the rates and drivers of headwall erosion within glaciated catchments in the NW Himalaya

Science.gov (United States)

Orr, E.; Owen, L. A.; Saha, S.; Caffee, M. W.

2017-12-01

Rates of headwall erosion are defined for fourteen glaciated catchments in the NW Himalaya by measuring 10Be terrestrial cosmogenic nuclide concentrations in supraglacial debris. The investigated catchments are located throughout three broad climatic zones, which include the Lesser Himalaya (rainfall >1000 mm a-1), Greater Himalaya (500-1000 mm a-1) and Transhimalaya (arid catchments that are occupied by sub-polar glaciers, suggesting that there are additional controls upon periglacial domain landscape change. Other factors and catchment-specific dynamics influencing these landscapes include, temperature, surface processes, topography, valley morphology, geologic setting and glacial history. Defining rates of headwall erosion is one of the first steps to understanding the nature of sediment production and transfer within high-altitude glaciated catchments, and highlights the importance of periglacial rockfall processes in landscape evolution.

In-situ buildup of cosmogenic isotopes at the earth's surface: measurement of erosion rates and exposure times

International Nuclear Information System (INIS)

Fifield, L.K.; Allan, G.L.; Stone, J.O.H.; Evans, J.M.; Cresswell, R.G.; Ophel, T.R.

1993-01-01

Cosmic rays produce a number of nuclides in rocks that can be used to determine the geomorphic history of surfaces. The most useful are the radioactive isotopes 10 Be (t 1/2 = 1.5Ma), 26 Al (0.7Ma) and 36 Cl (0.3Ma). Within the top 2m of the surface, these are produced principally by fast neutrons. At greater depths, production is dominated by the capture of negative muons. Measurements of a single nuclide produced in situ can be used to determine total exposure times or erosion rates. The use of multiple nuclides with different half-lives makes it possible to determine more complex histories, such as exposures interrupted by periods of burial. At the ANU, all three of the isotopes above are being used to study a variety of problems in geomorphology and paleoclimatology, although to date, most of the work has concentrated on 36 Cl. The accumulation of cosmogenic 36 Cl in calcite (CaCO 3 ) provides a means of measuring erosion rates on limestone surfaces. Sensitivity is achieved over a wide range of erosion rates due to the high production rate of 36 Cl in calcite (typically greater than 30 atoms/g/yr) and a detection limit of ca. 5000 atoms/g attainable with the ANU AMS system. The method is simplified by the predominance of Ca reactions (principally spallation) over other sources of 36 Cl in calcite, and the ease of sample preparation. This presentation discuss the results of measurements of 36 Cl in calcite from limestone samples from Australia and Papua New Guinea. Erosion rates derived from these measurements range from 3 microns per year (Australia) to over 200 microns per year in the New Guinea highlands. 3 refs

The effect of wet-dry weathering on the rate of bedrock river channel erosion by saltating gravel

Science.gov (United States)

Inoue, Takuya; Yamaguchi, Satomi; Nelson, Jonathan M.

2017-01-01

Previous work has shown that the bedrock erosion rate E because of collisions of saltating bedload can be expressed by E = βqb(1-Pc), where qb is the sediment transport rate, Pc is the extent of alluvial cover, and β is the abrasion coefficient. However, the dependence of the abrasion coefficient on the physical characteristics of the bedrock material is poorly known, and in particular, the effects of wet-dry weathering on the saltation-abrasion bedrock incision has not been specifically characterized. Observation suggests that the typical wet-dry cycling of exposed bedrock in river beds gives rise to cracks and voids that are likely to alter the incision rate of the material when subjected to impacts of moving sediment. In this study, flume experiments are performed to develop an understanding of how wet-dry cycling affects the rock tensile strength and the bedrock erosion rate. To represent the physical effects of weathering, boring cores taken from natural bedrock channel are exposed to artificial wet-dry cycles. The experimental results suggest the following: (1) the abrasion coefficient for fresh bedrock is estimated by β = 1.0 × 10− 4σT− 2(d/ksb)0.5, where σT is the tensile strength, d is the diameter of colliding gravel, and ksb is the hydraulic roughness height of bedrock; (2) the tensile strength of the bedrock decreases exponentially as a result of repeated wet-dry cycles, σT/σT0 = exp (-CTNWa0/σT0), where σT0 is the initial tensile strength, Wa0 is the initial normalized rate of water absorption., N is the number of wet-dry cycles, and CT is a constant; (3) the erosion rate of fresh bedrock depends on the inverse of the square of tensile strength, but the erosion rate of weathered bedrock depends on the − 1.5 power of tensile strength.

Estimates of soil erosion and deposition of cultivated soil of Nakhla watershed, Morocco, using 137Cs technique and calibration models

International Nuclear Information System (INIS)

Bouhlassa, S.; Moukhchane, M.; Aiachi, A.

2000-01-01

Despite the effective threat of erosion, for soil preservation and productivity in Morocco, there is still only limited information on rates of soil loss involved. This study is aimed to establish long-term erosion rates on cultivated land in the Nakhla watershed located in the north of the country, using 137 Cs technique. Two sampling strategies were adopted. The first is aimed at establishing areal estimates of erosion, whereas the second, based on a transect approach, intends to determine point erosion. Twenty-one cultivated sites and seven undisturbed sites apparently not affected by erosion or deposition were sampled to 35 cm depth. Nine cores were collected along the transect of 149 m length. The assessment of erosion rates with models varying in complexity from the simple Proportional Model to more complex Mass Balance Models which attempts to include the processes controlling the redistribution of 137 Cs in soil, enables us to demonstrate the significance of soil erosion problem on cultivated land. Erosion rates rises up to 50 t ha -1 yr -1 . The 137 Cs derived erosion rates provide a reliable representation of water erosion pattern in the area, and indicate the importance of tillage process on the redistribution of 137 Cs in soil. For aggrading sites a Constant Rate Supply (CRS) Model had been adapted and introduced to estimate easily the depositional rate. (author) [fr

Scenario Studies on Effects of Soil Infiltration Rates, Land Slope, and Furrow Irrigation Characteristics on Furrow Irrigation-Induced Erosion.

Science.gov (United States)

Dibal, Jibrin M; Ramalan, A A; Mudiare, O J; Igbadun, H E

2014-01-01

Furrow irrigation proceeds under several soil-water-furrow hydraulics interaction dynamics. The soil erosion consequences from such interactions in furrow irrigation in Samaru had remained uncertain. A furrow irrigation-induced erosion (FIIE) model was used to simulate the potential severity of soil erosion in irrigated furrows due to interactive effects of infiltration rates, land slope, and some furrow irrigation characteristics under different scenarios. The furrow irrigation characteristics considered were furrow lengths, widths, and stream sizes. The model itself was developed using the dimensional analysis approach. The scenarios studied were the interactive effects of furrow lengths, furrow widths, and slopes steepness; infiltration rates and furrow lengths; and stream sizes, furrow lengths, and slopes steepness on potential furrow irrigation-induced erosion, respectively. The severity of FIIE was found to relate somewhat linearly with slope and stream size, and inversely with furrow lengths and furrow width. The worst soil erosion (378.05 t/ha/yr) was found as a result of the interactive effects of 0.65 m furrow width, 50 m furrow length, and 0.25% slope steepness; and the least soil erosion (0.013 t/ha/yr) was induced by the combined effects of 0.5 l/s, 200 m furrow length, and 0.05% slope steepness. Evidently considering longer furrows in furrow irrigation designs would be a better alternative of averting excessive FIIE.

Lifespan of mountain ranges scaled by feedbacks between landsliding and erosion by rivers.

Science.gov (United States)

Egholm, David L; Knudsen, Mads F; Sandiford, Mike

2013-06-27

An important challenge in geomorphology is the reconciliation of the high fluvial incision rates observed in tectonically active mountain ranges with the long-term preservation of significant mountain-range relief in ancient, tectonically inactive orogenic belts. River bedrock erosion and sediment transport are widely recognized to be the principal controls on the lifespan of mountain ranges. But the factors controlling the rate of erosion and the reasons why they seem to vary significantly as a function of tectonic activity remain controversial. Here we use computational simulations to show that the key to understanding variations in the rate of erosion between tectonically active and inactive mountain ranges may relate to a bidirectional coupling between bedrock river incision and landslides. Whereas fluvial incision steepens surrounding hillslopes and increases landslide frequency, landsliding affects fluvial erosion rates in two fundamentally distinct ways. On the one hand, large landslides overwhelm the river transport capacity and cause upstream build up of sediment that protects the river bed from further erosion. On the other hand, in delivering abrasive agents to the streams, landslides help accelerate fluvial erosion. Our models illustrate how this coupling has fundamentally different implications for rates of fluvial incision in active and inactive mountain ranges. The coupling therefore provides a plausible physical explanation for the preservation of significant mountain-range relief in old orogenic belts, up to several hundred million years after tectonic activity has effectively ceased.

Erosion-corrosion interactions and their affect on marine and offshore components

Energy Technology Data Exchange (ETDEWEB)

Wood, Robert JK [Surface Engineering and Tribology Group, School of Engineering Sciences, University of Southampton, SO17 1BJ (United Kingdom)

2004-07-01

The operation of modern fluid handling systems demands for low costs, reliability, longevity and no loss of fluid containment. All these can be achieved by minimising the material damage caused by the combined attack of solid particle or cavitation impingement and corrosion. This paper will cover the rationale behind the selection of erosion resistance surfaces for fluid handling equipment and highlight the complexities encountered when these surfaces are exposed to environments which contain sand particles or cavitation in a corrosive medium. The erosion and erosion-corrosion performance of a variety of coatings and bulk surfaces will be discussed using volume loss rate versus sand impact energy maps. Recent research into the erosion-corrosion of polymer coatings, PEO and HVOF aluminium and nickel aluminium bronze coatings will be reviewed. Electrochemical techniques designed to monitor the erosion-corrosion mechanisms and coating integrity will be presented and used to quantify the synergistic terms present when both erosion and corrosion act concurrently. (author)

On researching erosion-corrosion wear in pipelines: the rate and residual lifetime estimation

International Nuclear Information System (INIS)

Baranenko, V.I.; Yanchenko, Yu.A.; Gulina, O.M.; Dokukin, D.A.

2010-01-01

To base the normative document on calculation of pipelines erosive-corrosive wear (ECW) rate and residual lifetime this research of ECW regularities for pearlitic steel NPP pipelines was performed. The estimates of control data treatment statistical procedures efficiency were presented. The influence of the scheme of piping control on the ECW rate and residual lifetime estimation results was demonstrated. The simplified scheme is valid only in case of complete information. It's usage under data uncertainties leads to essential residual lifetime overstating [ru

Crust behavior and erosion rate prediction of EPR sacrificial material impinged by core melt jet

Energy Technology Data Exchange (ETDEWEB)

Li, Gen; Liu, Ming, E-mail: ming.liu@mail.xjtu.edu.cn; Wang, Jinshi; Chong, Daotong; Yan, Junjie

2017-04-01

Highlights: • A numerical code was developed to analyze melt jet-concrete interaction in the frame of MPS method. • Crust and ablated concrete layer at UO{sub 2}-ZrO{sub 2} melt and concrete interface periodically developed and collapsed. • Concrete surface temperature fluctuated around a low temperature and ablation temperature. • Concrete erosion by Fe-Zr melt jet was significantly faster than that by UO{sub 2}-ZrO{sub 2} melt jet. - Abstract: Sacrificial material is a special ferro-siliceous concrete, designed in the ex-vessel core melt stabilization system of European Pressurized water Reactor (EPR). Given a localized break of RPV lower head, the melt directly impinges onto the dry concrete in form of compact jet. The concrete erosion behavior influences the failure of melt plug, and further affects melt spreading. In this study, a numerical code was developed in the frame of Moving Particle Semi-implicit (MPS) method, to analyze the crust behavior and erosion rate of sacrificial concrete, impinged by prototypic melt jet. In validation of numerical modeling, the time-dependent erosion depth and erosion configuration matched well with the experimental data. Sensitivity study of sacrificial concrete erosion indicates that the crust and ablated concrete layer presented at UO{sub 2}-ZrO{sub 2} melt and concrete interface, whereas no crust could be found in the interaction of Fe-Zr melt with concrete. The crust went through stabilization-fracture-reformation periodic process, accompanied with accumulating and collapsing of molten concrete layer. The concrete surface temperature fluctuated around a low temperature and ablation temperature. It increased as the concrete surface layer was heated to melting, and dropped down when the cold concrete was revealed. The erosion progression was fast in the conditions of small jet diameter and large concrete inclination angle, and it was significantly faster in the erosion by metallic melt jet than by oxidic melt jet.

STUDY OF RAINFALL RATES AND EROSIVE PROCESSES AT THE URBAN AREA OF SÃO LUÍS – MA

Directory of Open Access Journals (Sweden)

Antonio José Teixeira Guerra

2005-05-01

Full Text Available The study of the rain rates is here highlighted, in order to understand the mechanisms that generate the starting point of the erosive processes. The precipitation varies spatially not only in local and regional levels, due to mechanisms that generate rains, but also in short distances, due to the control of local variations, such as winds and constructions. In this way, the precipitations should be measured in different points of the study area, depending on the interest of the study and scale of analysis.The erosive process caused by rainfall covers almost the whole terrestrial surface, especially in tropical areas where the total rainfall is higher than in other regions of the planet. Besides that, the rain only falls on specific seasons in several areas, which worsens the erosion. The process tends to accelerate as the deforestation for wood exploitation and/or agricultural production takes place, once the soils become unprotected without the vegetal cover, so that the rains affect the surface of the grounds directly (GUERRA, 1999.This work presents the results of the monitoring of erosive processes along more than three years of studies at the urban area of São Luís City, relating rainfall rates to gullies evolution, an important instrument for the control and recovery of large-scale erosive processes.

A simplified 137Cs transport model for estimating erosion rates in undisturbed soil

International Nuclear Information System (INIS)

Zhang Xinbao; Long Yi; He Xiubin; Fu Jiexiong; Zhang Yunqi

2008-01-01

137 Cs is an artificial radionuclide with a half-life of 30.12 years which released into the environment as a result of atmospheric testing of thermo-nuclear weapons primarily during the period of 1950s-1970s with the maximum rate of 137 Cs fallout from atmosphere in 1963. 137 Cs fallout is strongly and rapidly adsorbed by fine particles in the surface horizons of the soil, when it falls down on the ground mostly with precipitation. Its subsequent redistribution is associated with movements of the soil or sediment particles. The 137 Cs nuclide tracing technique has been used for assessment of soil losses for both undisturbed and cultivated soils. For undisturbed soils, a simple profile-shape model was developed in 1990 to describe the 137 Cs depth distribution in profile, where the maximum 137 Cs occurs in the surface horizon and it exponentially decreases with depth. The model implied that the total 137 Cs fallout amount deposited on the earth surface in 1963 and the 137 Cs profile shape has not changed with time. The model has been widely used for assessment of soil losses on undisturbed land. However, temporal variations of 137 Cs depth distribution in undisturbed soils after its deposition on the ground due to downward transport processes are not considered in the previous simple profile-shape model. Thus, the soil losses are overestimated by the model. On the base of the erosion assessment model developed by Walling, D.E., He, Q. [1999. Improved models for estimating soil erosion rates from cesium-137 measurements. Journal of Environmental Quality 28, 611-622], we discuss the 137 Cs transport process in the eroded soil profile and make some simplification to the model, develop a method to estimate the soil erosion rate more expediently. To compare the soil erosion rates calculated by the simple profile-shape model and the simple transport model, the soil losses related to different 137 Cs loss proportions of the reference inventory at the Kaixian site of the

Validating a mass balance accounting approach to using 7Be measurements to estimate event-based erosion rates over an extended period at the catchment scale

Science.gov (United States)

Porto, Paolo; Walling, Des E.; Cogliandro, Vanessa; Callegari, Giovanni

2016-07-01

Use of the fallout radionuclides cesium-137 and excess lead-210 offers important advantages over traditional methods of quantifying erosion and soil redistribution rates. However, both radionuclides provide information on longer-term (i.e., 50-100 years) average rates of soil redistribution. Beryllium-7, with its half-life of 53 days, can provide a basis for documenting short-term soil redistribution and it has been successfully employed in several studies. However, the approach commonly used introduces several important constraints related to the timing and duration of the study period. A new approach proposed by the authors that overcomes these constraints has been successfully validated using an erosion plot experiment undertaken in southern Italy. Here, a further validation exercise undertaken in a small (1.38 ha) catchment is reported. The catchment was instrumented to measure event sediment yields and beryllium-7 measurements were employed to document the net soil loss for a series of 13 events that occurred between November 2013 and June 2015. In the absence of significant sediment storage within the catchment's ephemeral channel system and of a significant contribution from channel erosion to the measured sediment yield, the estimates of net soil loss for the individual events could be directly compared with the measured sediment yields to validate the former. The close agreement of the two sets of values is seen as successfully validating the use of beryllium-7 measurements and the new approach to obtain estimates of net soil loss for a sequence of individual events occurring over an extended period at the scale of a small catchment.

Using "1"3"7Cs measurements to estimate soil erosion rates in the Pčinja and South Morava River Basins, southeastern Serbia

International Nuclear Information System (INIS)

Petrović, Jelena; Dragović, Snežana; Dragović, Ranko; Đorđević, Milan; Đokić, Mrđan; Zlatković, Bojan; Walling, Desmond

2016-01-01

The need for reliable assessments of soil erosion rates in Serbia has directed attention to the potential for using "1"3"7Cs measurements to derive estimates of soil redistribution rates. Since, to date, this approach has not been applied in southeastern Serbia, a reconnaissance study was undertaken to confirm its viability. The need to take account of the occurrence of substantial Chernobyl fallout was seen as a potential problem. Samples for "1"3"7Cs measurement were collected from a zone of uncultivated soils in the watersheds of Pčinja and South Morava Rivers, an area with known high soil erosion rates. Two theoretical conversion models, the profile distribution (PD) model and diffusion and migration (D&M) model were used to derive estimates of soil erosion and deposition rates from the "1"3"7Cs measurements. The estimates of soil redistribution rates derived by using the PD and D&M models were found to differ substantially and this difference was ascribed to the assumptions of the simpler PD model that cause it to overestimate rates of soil loss. The results provided by the D&M model were judged to more reliable. - Highlights: • The "1"3"7Cs measurements are employed to estimate the soil erosion and deposition rates in southeastern Serbia. • Estimates of annual soil loss by profile distribution (PD) and diffusion and migration (D&M) models differ significantly. • Differences were ascribed to the assumptions of the simpler PD model which cause it to overestimate rates of soil loss. • The study confirmed the potential for using "1"3"7Cs measurements to estimate soil erosion rates in Serbia.

The contribution of mulches to control high soil erosion rates in vineyards in Eastern Spain

Science.gov (United States)

Cerdà, Artemi; Jordán, Antonio; Zavala, Lorena; José Marqués, María; Novara, Agata

2014-05-01

Soil erosion take place in degraded ecosystem where the lack of vegetation, drought, erodible parent material and deforestation take place (Borelli et al., 2013; Haregeweyn et al., 2013; Zhao et al., 2013). Agriculture management developed new landscapes (Ore and Bruins, 2012) and use to trigger non-sustainable soil erosion rates (Zema et al., 2012). High erosion rates were measured in agriculture land (Cerdà et al., 2009), but it is also possible to develop managements that will control the soil and water losses, such as organic amendments (Marqués et al., 2005), plant cover (Marqués et al., 2007) and geotextiles (Giménez Morera et al., 2010). The most successful management to restore the structural stability and the biological activity of the agriculture soil has been the organic mulches (García Orenes et al; 2009; 2010; 2012). The straw mulch is also very successful on bare fire affected soil (Robichaud et al., 2013a; 2013b), which also contributes to a more stable soil moisture content (García-Moreno et al., 2013). The objective of this research is to determine the impact of two mulches: wheat straw and chipped branches, on the soil erosion rates in a rainfed vineyard in Eastern Spain. The research site is located in the Les Alcusses Valley within the Moixent municipality. The Mean annual temperature is 13 ºC, and the mean annual rainfall 455 mm. Soil are sandy loam, and are developed at the foot-slope of a Cretaceous limestone range, the Serra Grossa range. The soils use to be ploughed and the features of soil erosion are found after each thunderstorm. Rills are removed by ploughing. Thirty rainfall simulation experiments were carried out in summer 2011 during the summer drought period. The simulated rainfall lasted during 1 hour at a 45 mmh-1 intensity on 1 m2 plots (Cerdà and Doerr, 2010; Cerdà and Jurgensen 2011). Ten experiments were carried out on the control plots (ploughed), 10 on straw mulch covered plots, and 10 on chipped branches covered

Experimental study of the cavitation erosion in centrifugal pump impeller

International Nuclear Information System (INIS)

Rayan, M.A.

1985-01-01

Research on cavitation damage scale effects show that the damage rate is increased with size and velocity. It seems that for constant velocity there is no clear trend for the variation of erosion with cavitation number. Research on the time effects on damage rate show similarity between cavitation and impingement erosion. The cumulative weight loss versus time curve is of a ''S'' shaped type characterized by an incubation period followed by a period of increasing erosion rate, then a maximum erosion rate, and finally a period of decreasing erosion rate. The objective of this investigation is to present a prototype cavitation erosion experiment in order to clarify the time dependency of the erosive wear

Using 137Cs measurements to investigate the influence of erosion and soil redistribution on soil properties

International Nuclear Information System (INIS)

Du, P.; Walling, D.E.

2011-01-01

Information on the interaction between soil erosion and soil properties is an important requirement for sustainable management of the soil resource. The relationship between soil properties and the soil redistribution rate, reflecting both erosion and deposition, is an important indicator of this interaction. This relationship is difficult to investigate using traditional approaches to documenting soil redistribution rates involving erosion plots and predictive models. However, the use of the fallout radionuclide 137 Cs to document medium-term soil redistribution rates offers a means of overcoming many of the limitations associated with traditional approaches. The study reported sought to demonstrate the potential for using 137 Cs measurements to assess the influence of soil erosion and redistribution on soil properties (particle size composition, total C, macronutrients N, P, K and Mg, micronutrients Mn, Mo, Fe, Cu and Zn and other elements, including Ti and As). 137 Cs measurements undertaken on 52 soil cores collected within a 7 ha cultivated field located near Colebrooke in Devon, UK were used to establish the magnitude and spatial pattern of medium-term soil redistribution rates within the field. The soil redistribution rates documented for the individual sampling points within the field ranged from an erosion rate of -12.9 t ha -1 yr -1 to a deposition rate of 19.2 t ha -1 yr -1 . Composite samples of surface soil (0-5 cm) were collected immediately adjacent to each coring point and these samples were analysed for a range of soil properties. Individual soil properties associated with these samples showed significant variability, with CV values generally lying in the range 10-30%. The relationships between the surface soil properties and the soil redistribution rate were analysed. This analysis demonstrated statistically significant relationships between some soil properties (total phosphorus, % clay, Ti and As) and the soil redistribution rate, but for most

Long-term modeling of soil C erosion and sequestration at the small watershed scale

International Nuclear Information System (INIS)

Izaurralde, R.C.; Thomson, A.M.; Williams, J.R.; Post, W.M.; McGill, W.B.; Owens, L.B.; Lal, R.

2007-01-01

The soil C balance is determined by the difference between inputs (e.g., plant litter, organic amendments, depositional C) and outputs (e.g., soil respiration, dissolved organic C leaching, and eroded C). There is a need to improve our understanding of whether soil erosion is a sink or a source of atmospheric CO2. The objective of this paper is to discover the long-term influence of soil erosion on the C cycle of managed watersheds near Coshocton, OH. We hypothesize that the amount of eroded C that is deposited in or out of a watershed compares in magnitude to the soil C changes induced via microbial respiration. We applied the erosion productivity impact calculator (EPIC) model to evaluate the role of erosion-deposition processes on the C balance of three small watersheds (∼1 ha). Experimental records from the USDA North Appalachian Experimental Watershed facility north of Coshocton, OH were used in the study. Soils are predominantly silt loam and have developed from loess-like deposits over residual bedrock. Management practices in the three watersheds have changed over time. Currently, watershed 118 (W118) is under a corn (Zea mays L.)-soybean (Glycine max [L.] Merr.) no till rotation, W128 is under conventional till continuous corn, and W188 is under no till continuous corn. Simulations of a comprehensive set of ecosystem processes including plant growth, runoff, and water erosion were used to quantify sediment C yields. A simulated sediment C yield of 43 ± 22 kg C ha -1 year -1 compared favorably against the observed 31 ± 12 kg C ha -1 year -1 in W118. EPIC overestimated the soil C stock in the top 30-cm soil depth in W118 by 21% of the measured value (36.8 Mg C ha -1 ). Simulations of soil C stocks in the other two watersheds (42.3 Mg C ha -1 in W128 and 50.4 Mg C ha -1 in W188) were off by -1 . Simulated eroded C re-deposited inside (30-212 kg C ha -1 year -1 ) or outside (73 -1 79 kg C ha -1 year -1 ) watershed boundaries compared in magnitude to a

Using (137)Cs measurements to estimate soil erosion rates in the Pčinja and South Morava River Basins, southeastern Serbia.

Science.gov (United States)

Petrović, Jelena; Dragović, Snežana; Dragović, Ranko; Đorđević, Milan; Đokić, Mrđan; Zlatković, Bojan; Walling, Desmond

2016-07-01

The need for reliable assessments of soil erosion rates in Serbia has directed attention to the potential for using (137)Cs measurements to derive estimates of soil redistribution rates. Since, to date, this approach has not been applied in southeastern Serbia, a reconnaissance study was undertaken to confirm its viability. The need to take account of the occurrence of substantial Chernobyl fallout was seen as a potential problem. Samples for (137)Cs measurement were collected from a zone of uncultivated soils in the watersheds of Pčinja and South Morava Rivers, an area with known high soil erosion rates. Two theoretical conversion models, the profile distribution (PD) model and diffusion and migration (D&M) model were used to derive estimates of soil erosion and deposition rates from the (137)Cs measurements. The estimates of soil redistribution rates derived by using the PD and D&M models were found to differ substantially and this difference was ascribed to the assumptions of the simpler PD model that cause it to overestimate rates of soil loss. The results provided by the D&M model were judged to more reliable. Copyright © 2016 Elsevier Ltd. All rights reserved.

A field experiment on the controls of sediment transport on bedrock erosion

Science.gov (United States)

Beer, A. R.; Turowski, J. M.; Fritschi, B.; Rieke-Zapp, D.; Campana, L.; Lavé, J.

2012-12-01

The earth`s surface is naturally shaped by interactions of physical and chemical processes. In mountainous regions with steep topography river incision fundamentally controls the geomorphic evolution of the whole landscape. There, erosion of exposed bedrock sections by fluvial sediment transport is an important mechanism forming mountain river channels. The links between bedload transport and bedrock erosion has been firmly established using laboratory experiments. However, there are only few field datasets linking discharge, sediment transport, impact energy and erosion that can be used for process understanding and model evaluation. To fill this gap, a new measuring setup has been commissioned to raise an appropriate simultaneous dataset of hydraulics, sediment transport and bedrock erosion at high temporal and spatial resolution. Two natural stone slabs were installed flush with the streambed of the Erlenbach, a gauged stream in the Swiss Pre-Alps. They are mounted upon force sensors recording vertical pressure und downstream shear caused by passing sediment particles. The sediment transport rates can be assessed using geophone plates and an automated moving basket system taking short-term sediment samples. These devices are located directly downstream of the stone slabs. Bedrock erosion rates are measured continuously with erosion sensors at sub-millimeter accuracy at three points on each slab. In addition, the whole slab topography is surveyed with photogrammetry and a structured-light 3D scanner after individual flood events. Since the installation in 2011, slab bedrock erosion has been observed during several transport events. We discuss the relation between hydraulics, bedload transport, resulting pressure forces on the stone slabs and erosion rates. The aim of the study is the derivation of an empirical process law for fluvial bedrock erosion driven by moving sediment particles.

Modeling soil erosion in a watershed

OpenAIRE

Lanuza, R.

1999-01-01

Most erosion models have been developed based on a plot scale and have limited application to a watershed due to the differences in aerial scale. In order to address this limitation, a GIS-assisted methodology for modeling soil erosion was developed using PCRaster to predict the rate of soil erosion at watershed level; identify the location of erosion prone areas; and analyze the impact of landuse changes on soil erosion. The general methodology of desktop modeling or soil erosion at watershe...

Spatial bedrock erosion distribution in a natural gorge

Science.gov (United States)

Beer, A. R.; Turowski, J. M.; Kirchner, J. W.

2015-12-01

Quantitative analysis of morphological evolution both in terrestrial and planetary landscapes is of increasing interest in the geosciences. In mountainous regions, bedrock channel formation as a consequence of the interaction of uplift and erosion processes is fundamental for the entire surface evolution. Hence, the accurate description of bedrock channel development is important for landscape modelling. To verify existing concepts developed in the lab and to analyse how in situ channel erosion rates depend on the interrelations of discharge, sediment transport and topography, there is a need of highly resolved topographic field data. We analyse bedrock erosion over two years in a bedrock gorge downstream of the Gorner glacier above the town of Zermatt, Switzerland. At the study site, the Gornera stream cuts through a roche moutonnée in serpentine rock of 25m length, 5m width and 8m depth. We surveyed bedrock erosion rates using repeat terrestrial laser scanning (TLS) with an average point spacing of 5mm. Bedrock erosion rates in direction of the individual surface normals were studied directly on the scanned point clouds applying the M3C2 algorithm (Lague et al., 2013, ISPRS). The surveyed erosion patterns were compared to a simple stream erosivity visualisation obtained from painted bedrock sections at the study location. Spatially distributed erosion rates on bedrock surfaces based on millions of scan points allow deduction of millimeter-scale mean annual values of lateral erosion, incision and downstream erosion on protruding streambed surfaces. The erosion rate on a specific surface point is shown to depend on the position of this surface point in the channel's cross section, its height above the streambed and its spatial orientation to the streamflow. Abrasion by impacting bedload was likely the spatially dominant erosion process, as confirmed by the observed patterns along the painted bedrock sections. However, a single plucking event accounted for the half

In-situ buildup of cosmogenic isotopes at the earth`s surface: measurement of erosion rates and exposure times

Energy Technology Data Exchange (ETDEWEB)

Fifield, L K; Allan, G L; Stone, J O.H.; Evans, J M; Cresswell, R G; Ophel, T R [Australian National Univ., Canberra, ACT (Australia)

1994-12-31

Cosmic rays produce a number of nuclides in rocks that can be used to determine the geomorphic history of surfaces. The most useful are the radioactive isotopes {sup 10}Be (t{sub 1/2} = 1.5Ma), {sup 26}Al (0.7Ma) and {sup 36}Cl (0.3Ma). Within the top 2m of the surface, these are produced principally by fast neutrons. At greater depths, production is dominated by the capture of negative muons. Measurements of a single nuclide produced in situ can be used to determine total exposure times or erosion rates. The use of multiple nuclides with different half-lives makes it possible to determine more complex histories, such as exposures interrupted by periods of burial. At the ANU, all three of the isotopes above are being used to study a variety of problems in geomorphology and paleoclimatology, although to date, most of the work has concentrated on {sup 36}Cl. The accumulation of cosmogenic {sup 36}Cl in calcite (CaCO{sub 3}) provides a means of measuring erosion rates on limestone surfaces. Sensitivity is achieved over a wide range of erosion rates due to the high production rate of {sup 36}Cl in calcite (typically greater than 30 atoms/g/yr) and a detection limit of ca. 5000 atoms/g attainable with the ANU AMS system. The method is simplified by the predominance of Ca reactions (principally spallation) over other sources of {sup 36}Cl in calcite, and the ease of sample preparation. This presentation discuss the results of measurements of {sup 36}Cl in calcite from limestone samples from Australia and Papua New Guinea. Erosion rates derived from these measurements range from 3 microns per year (Australia) to over 200 microns per year in the New Guinea highlands. 3 refs.

In-situ buildup of cosmogenic isotopes at the earth`s surface: measurement of erosion rates and exposure times

Energy Technology Data Exchange (ETDEWEB)

Fifield, L.K.; Allan, G.L.; Stone, J.O.H.; Evans, J.M.; Cresswell, R.G.; Ophel, T.R. [Australian National Univ., Canberra, ACT (Australia)

1993-12-31

Cosmic rays produce a number of nuclides in rocks that can be used to determine the geomorphic history of surfaces. The most useful are the radioactive isotopes {sup 10}Be (t{sub 1/2} = 1.5Ma), {sup 26}Al (0.7Ma) and {sup 36}Cl (0.3Ma). Within the top 2m of the surface, these are produced principally by fast neutrons. At greater depths, production is dominated by the capture of negative muons. Measurements of a single nuclide produced in situ can be used to determine total exposure times or erosion rates. The use of multiple nuclides with different half-lives makes it possible to determine more complex histories, such as exposures interrupted by periods of burial. At the ANU, all three of the isotopes above are being used to study a variety of problems in geomorphology and paleoclimatology, although to date, most of the work has concentrated on {sup 36}Cl. The accumulation of cosmogenic {sup 36}Cl in calcite (CaCO{sub 3}) provides a means of measuring erosion rates on limestone surfaces. Sensitivity is achieved over a wide range of erosion rates due to the high production rate of {sup 36}Cl in calcite (typically greater than 30 atoms/g/yr) and a detection limit of ca. 5000 atoms/g attainable with the ANU AMS system. The method is simplified by the predominance of Ca reactions (principally spallation) over other sources of {sup 36}Cl in calcite, and the ease of sample preparation. This presentation discuss the results of measurements of {sup 36}Cl in calcite from limestone samples from Australia and Papua New Guinea. Erosion rates derived from these measurements range from 3 microns per year (Australia) to over 200 microns per year in the New Guinea highlands. 3 refs.

An Analytical Model for Basin-scale Glacier Erosion as a Function of Climate and Topography

Science.gov (United States)

Jaffrey, M.; Hallet, B.

2017-12-01

Knowledge about glacier erosion has advanced considerably over the last few decades with the emergence of a firm mechanistic understanding of abrasion and quarrying, the growing sophistication of complex numerical models of glacial erosion and the evolution of glacial landforms, and the increase in data from field studies of erosion rates. Interest in glacial erosion has also intensified and diversified substantially as it is increasingly recognized as a key process affecting the heights of mountains, the overall evolution of mountain belts, and the coupling of climate, erosion, and tectonics. Yet, the general controls of glacier erosion rates have not been addressed theoretically, and the large range of published basin-scale erosion rates, covering more than 3 orders of magnitude, remains poorly understood. To help gain insight into glacier erosion rates at the scale of glacier basins, the only scale for which extensive data exist, we develop analytically a simple budget of the total mechanical energy per unit time, the power, dissipated by a steady state glacier in sliding, S, and viscous deformation, V. We hypothesize that the power for the work of erosion derives solely from S and that the basin wide erosion rate scales with S averaged over the basin. We solve the power budget directly in terms of climatic and topographic parameters, showing explicitly that the source of power to drive both S and V is the gravitational power supplied by the net snow accumulation (mass balance). The budget leads to the simple metric φ=mbΔz2 for the basin average of S with Δz being the glacier basin relief and mb the gradient of the mass balance with elevation. The dependence of φ on the square of the relief arises from both the mass balance's and potential energy's linear increases with elevation. We validate φ using results from a comprehensive field study of erosion rates paired with glaciological data along a transect extending from Southern Patagonia to the Antarctic

Soil movements and surface erosion rates on rocky slopes in the mountain areas of the karst region of Southwest China

Science.gov (United States)

Zhang, X. B.; Bai, X. Y.; Long, Y.

2012-04-01

The karst region of Southwest China with an area of 54 × 104 km2 is one of the largest karst areas in the world and experiences subtropical climate. Hill-depressions are common landforms in the mountain areas of this region. Downslope soil movement on the ground by surface water erosion and soil sinking into underground holes by creeping or pipe erosion are mayor types of soil movements on rocky carbonate slopes. The 137Cs technique was used to date the sediment deposits in six karst depressions, to estimate average surface erosion rates on slopes from their catchments. The estimates of soil loss rates obtained from this study evidenced considerable variability. A value of 1.0 t km-2 year-1 was obtained for a catchment under original dense karst forest, but the erosion rates ranged between 19.3 t km-2 year-1 and 48.7 t km-2 year-1 in four catchments under secondary forest or grasses, where the original forest cover had been removed in the Ming and Qing dynasties, several hundred years ago. The highest rate of 1643 t km-2 year-1 was obtained for a catchment underlain by clayey carbonate rocks, where the soil cover was thicker and more extensive than in the other catchments and extensive land reclamation for cultivation had occurred during the period 1979-1981, immediately after the Cultural Revolution.

Coupled Wave Energy and Erosion Dynamics along a Salt Marsh Boundary, Hog Island Bay, Virginia, USA

Directory of Open Access Journals (Sweden)

Anthony M. Priestas

2015-09-01

Full Text Available The relationship between lateral erosion of salt marshes and wind waves is studied in Hog Island Bay, Virginia USA, with high-resolution field measurements and aerial photographs. Marsh retreat is compared to wave climate calculated in the bay using the spectral wave-model Simulating Waves Nearshore (SWAN. We confirm the existence of a linear relationship between long-term salt marsh erosion and wave energy, and show that wave power can serve as a good proxy for average salt-marsh erosion rates. At each site, erosion rates are consistent across several temporal scales, ranging from months to decades, and are strongly related to wave power. On the contrary, erosion rates vary in space and weakly depend on the spatial distribution of wave energy. We ascribe this variability to spatial variations in geotechnical, biological, and morphological marsh attributes. Our detailed field measurements indicate that at a small spatial scale (tens of meters, a positive feedback between salt marsh geometry and wave action causes erosion rates to increase with boundary sinuosity. However, at the scale of the entire marsh boundary (hundreds of meters, this relationship is reversed: those sites that are more rapidly eroding have a marsh boundary which is significantly smoother than the marsh boundary of sheltered and slowly eroding marshes.

Erosion characteristics and horizontal variability for small erosion depths in the Sacramento-San Joaquin River Delta, California, USA

Science.gov (United States)

Schoellhamer, David H.; Manning, Andrew J.; Work, Paul A.

2017-01-01

Erodibility of cohesive sediment in the Sacramento-San Joaquin River Delta (Delta) was investigated with an erosion microcosm. Erosion depths in the Delta and in the microcosm were estimated to be about one floc diameter over a range of shear stresses and times comparable to half of a typical tidal cycle. Using the conventional assumption of horizontally homogeneous bed sediment, data from 27 of 34 microcosm experiments indicate that the erosion rate coefficient increased as eroded mass increased, contrary to theory. We believe that small erosion depths, erosion rate coefficient deviation from theory, and visual observation of horizontally varying biota and texture at the sediment surface indicate that erosion cannot solely be a function of depth but must also vary horizontally. We test this hypothesis by developing a simple numerical model that includes horizontal heterogeneity, use it to develop an artificial time series of suspended-sediment concentration (SSC) in an erosion microcosm, then analyze that time series assuming horizontal homogeneity. A shear vane was used to estimate that the horizontal standard deviation of critical shear stress was about 30% of the mean value at a site in the Delta. The numerical model of the erosion microcosm included a normal distribution of initial critical shear stress, a linear increase in critical shear stress with eroded mass, an exponential decrease of erosion rate coefficient with eroded mass, and a stepped increase in applied shear stress. The maximum SSC for each step increased gradually, thus confounding identification of a single well-defined critical shear stress as encountered with the empirical data. Analysis of the artificial SSC time series with the assumption of a homogeneous bed reproduced the original profile of critical shear stress, but the erosion rate coefficient increased with eroded mass, similar to the empirical data. Thus, the numerical experiment confirms the small-depth erosion hypothesis. A linear

Robotic weld overlay coatings for erosion control

Science.gov (United States)

The erosion of materials by the impact of solid particles has received increasing attention during the past twenty years. Recently, research has been initiated with the event of advanced coal conversion processes in which erosion plays an important role. The resulting damage, termed Solid Particle Erosion (SPE), is of concern primarily because of the significantly increased operating costs which result in material failures. Reduced power plant efficiency due to solid particle erosion of boiler tubes and waterfalls has led to various methods to combat SPE. One method is to apply coatings to the components subjected to erosive environments. Protective weld overlay coatings are particularly advantageous in terms of coating quality. The weld overlay coatings are essentially immune to spallation due to a strong metallurgical bond with the substrate material. By using powder mixtures, multiple alloys can be mixed in order to achieve the best performance in an erosive environment. However, a review of the literature revealed a lack of information on weld overlay coating performance in erosive environments which makes the selection of weld overlay alloys a difficult task. The objective of this project is to determine the effects of weld overlay coating composition and microstructure on erosion resistance. These results will lead to a better understanding of erosion mitigation in CFB's.

Nanoscale coatings for erosion and corrosion protection of copper microchannel coolers for high powered laser diodes

Science.gov (United States)

Flannery, Matthew; Fan, Angie; Desai, Tapan G.

2014-03-01

High powered laser diodes are used in a wide variety of applications ranging from telecommunications to industrial applications. Copper microchannel coolers (MCCs) utilizing high velocity, de-ionized water coolant are used to maintain diode temperatures in the recommended range to produce stable optical power output and control output wavelength. However, aggressive erosion and corrosion attack from the coolant limits the lifetime of the cooler to only 6 months of operation. Currently, gold plating is the industry standard for corrosion and erosion protection in MCCs. However, this technique cannot perform a pin-hole free coating and furthermore cannot uniformly cover the complex geometries of current MCCs involving small diameter primary and secondary channels. Advanced Cooling Technologies, Inc., presents a corrosion and erosion resistant coating (ANCERTM) applied by a vapor phase deposition process for enhanced protection of MCCs. To optimize the coating formation and thickness, coated copper samples were tested in 0.125% NaCl solution and high purity de-ionized (DIW) flow loop. The effects of DIW flow rates and qualities on erosion and corrosion of the ANCERTM coated samples were evaluated in long-term erosion and corrosion testing. The robustness of the coating was also evaluated in thermal cycles between 30°C - 75°C. After 1000 hours flow testing and 30 thermal cycles, the ANCERTM coated copper MCCs showed a corrosion rate 100 times lower than the gold plated ones and furthermore were barely affected by flow rates or temperatures thus demonstrating superior corrosion and erosion protection and long term reliability.

Definition of tolerable soil erosion values

Directory of Open Access Journals (Sweden)

G. Sparovek

1997-09-01

Full Text Available Although the criteria for defining erosion tolerance are well established, the limits generally used are not consistent with natural, economical and technological conditions. Rates greater than soil formation can be accepted only until a minimum of soil depth is reached, provided that they are not associated with environmental hazard or productivity losses. A sequence of equations is presented to calculate erosion tolerance rates through time. The selection of equation parameters permits the definition of erosion tolerance rates in agreement with environmental, social and technical needs. The soil depth change that is related to irreversible soil degradation can be calculated. The definition of soil erosion tolerance according to these equations can be used as a guideline for sustainable land use planning and is compatible with expert systems.

Effectiveness assessment of soil conservation measures in reducing soil erosion in Baiquan County of Northeastern China by using (137)Cs techniques.

Science.gov (United States)

Zhang, Qing-Wen; Li, Yong

2014-05-01

Accelerated soil erosion is considered as a major land degradation process resulting in increased sediment production and sediment-associated nutrient inputs to the rivers. Over the last decade, several soil conservation programs for erosion control have been conducted throughout Northeastern China. Reliable information on soil erosion rates is an essential prerequisite to assess the effectiveness of soil conservation measures. A study was carried out in Baiquan County of Northeastern China to assess the effectiveness of soil conservation measures in reducing soil erosion using the (137)Cs tracer technique and related techniques. This study reports the use of (137)Cs measurements to quantify medium-term soil erosion rates in traditional slope farmland, contour cropping farmland and terrace farmland in the Dingjiagou catchment and the Xingsheng catchment of Baiquan County. The (137)Cs reference inventory of 2532 ± 670 Bq m(-2) was determined. Based on the principle of the (137)Cs tracer technique, soil erosion rates were estimated. The results showed that severe erosion on traditional slope farmland is the dominant soil erosion process in the area. The terrace measure reduced soil erosion rates by 16% for the entire slope. Typical net soil erosion rates are estimated to be 28.97 Mg per hectare per year for traditional slope farmland and 25.04 Mg per hectare per year for terrace farmland in the Dingjiagou catchment. In contrast to traditional slope farmland with a soil erosion rate of 34.65 Mg per hectare per year, contour cultivation reduced the soil erosion rate by 53% resulting in a soil erosion rate of 22.58 Mg per hectare per year in the Xingsheng catchment. These results indicated that soil losses can be controlled by changing tillage practices from the traditional slope farmland cultivation to the terrace or contour cultivation.

Sediment budget for Murder Creek, Georgia, USA, from Pu239+240 - determined soil erosion rates

Science.gov (United States)

Stubblefield, A. P.; Matissoff, G.; Ketterer, M. E.; Whiting, P. J.

2005-12-01

Soil inventories of the radionuclides Cs137 and Pb210 have been used in a variety of environments as indicators for erosion and depositional processes. Development of sediment budgets for entire watersheds from radionuclide data has been somewhat constrained because limited sample numbers may not adequately characterize the wide range of geomorphic conditions and land uses found in heterogeneous environments. The measurement of Pu239+240 shows great potential for developing quantitative watershed sediment budgets. With inductively-coupled plasma mass spectrometry, hundreds of samples may be processed in dramatically shorter times than the gamma spectrometry method used for Cs137 or alpha spectrometry method used for Pb210. We collected surface soil samples from Murder Creek in the Piedmont region of Georgia, USA, to compare Pu239+240 inventories with Cs137 and Pb210 inventories for a range of land uses in a predominantly forested watershed. Excellent correlations were found for radionuclide inventories (r2 =0.88, n = 38) and high resolution (4 mm) depth profiles. The second objective was to generate a sediment budget using the full Pu239+240 dataset (n = 309). Average Pu239+240 inventories were 70.0 Bq/m2 for hardwood forest, 60.0 Bq/m2 for pine plantation, 65.1 Bq/m2 for pine forest, 66.7 Bq/m2 for row crop agriculture and 67.9 Bq/m2 for pasture. The sediment budget will be constructed by converting inventories into site-specific erosion rates. Erosion rates will be scaled up to the watershed scale using GIS coverages of land use, soil, slope, and slope position. Results will be compared with Murder Creek sediment budgets in the scientific literature generated from RUSLE erosion modeling, USGS monitoring networks and reservoir sedimentation.

Ecological site-based assessments of wind and water erosion: informing accelerated soil erosion management in rangelands

Science.gov (United States)

Webb, Nicholas P.; Herrick, Jeffrey E.; Duniway, Michael C.

2014-01-01

Accelerated soil erosion occurs when anthropogenic processes modify soil, vegetation or climatic conditions causing erosion rates at a location to exceed their natural variability. Identifying where and when accelerated erosion occurs is a critical first step toward its effective management. Here we explore how erosion assessments structured in the context of ecological sites (a land classification based on soils, landscape setting and ecological potential) and their vegetation states (plant assemblages that may change due to management) can inform systems for reducing accelerated soil erosion in rangelands. We evaluated aeolian horizontal sediment flux and fluvial sediment erosion rates for five ecological sites in southern New Mexico, USA, using monitoring data and rangeland-specific wind and water erosion models. Across the ecological sites, plots in shrub-encroached and shrub-dominated vegetation states were consistently susceptible to aeolian sediment flux and fluvial sediment erosion. Both processes were found to be highly variable for grassland and grass-succulent states across the ecological sites at the plot scale (0.25 Ha). We identify vegetation thresholds that define cover levels below which rapid (exponential) increases in aeolian sediment flux and fluvial sediment erosion occur across the ecological sites and vegetation states. Aeolian sediment flux and fluvial erosion in the study area can be effectively controlled when bare ground cover is 100 cm in length is less than ~35%. Land use and management activities that alter cover levels such that they cross thresholds, and/or drive vegetation state changes, may increase the susceptibility of areas to erosion. Land use impacts that are constrained within the range of natural variability should not result in accelerated soil erosion. Evaluating land condition against the erosion thresholds identified here will enable identification of areas susceptible to accelerated soil erosion and the development of

Ecological site‐based assessments of wind and water erosion: informing accelerated soil erosion management in rangelands.

Science.gov (United States)

Webb, Nicholas P; Herrick, Jeffrey E; Duniway, Michael C

Accelerated soil erosion occurs when anthropogenic processes modify soil, vegetation, or climatic conditions causing erosion rates at a location to exceed their natural variability. Identifying where and when accelerated erosion occurs is a critical first step toward its effective management. Here we explored how erosion assessments structured in the context of ecological sites (a land classification based on soils, landscape setting, and ecological potential) and their vegetation states (plant assemblages that may change due to management) can inform systems for reducing accelerated soil erosion in rangelands. We evaluated aeolian horizontal sediment flux and fluvial sediment erosion rates for five ecological sites in southern New Mexico, USA, using monitoring data and rangeland-specific wind and water erosion models. Across the ecological sites, plots in shrub-encroached and shrub-dominated vegetation states were consistently susceptible to aeolian sediment flux and fluvial sediment erosion. Both processes were found to be highly variable for grassland and grass–succulent states across the ecological sites at the plot scale (0.25 ha). We identified vegetation thresholds that define cover levels below which rapid (exponential) increases in aeolian sediment flux and fluvial sediment erosion occur across the ecological sites and vegetation states. Aeolian sediment flux and fluvial erosion in the study area could be effectively controlled when bare ground cover was 100 cm in length was less than ∼35%. Land use and management activities that alter cover levels such that they cross thresholds, and/or drive vegetation state changes, may increase the susceptibility of areas to erosion. Land use impacts that are constrained within the range of natural variability should not result in accelerated soil erosion. Evaluating land condition against the erosion thresholds identified here will enable identification of areas susceptible to accelerated soil erosion and the

Plio-Pleistocene paleo-erosion rates as a recorder of orographic barrier uplift in the NW-Argentine Andes (Humahuaca Basin)

Science.gov (United States)

Pingel, Heiko; Schildgen, Taylor; Wittmann, Hella

2017-04-01

As an integral part of the Eastern Cordillera, the intermontane Humahuaca Basin in the NW Argentine Andes is located in transition between the arid and internally drained Puna Plateau to the west and the humid broken foreland to the east. In combination with moisture-bearing air masses sourced in the Atlantic Ocean and the Amazon Basin, the present-day topographic gradient of the eastern Andean margin comprises an efficient orographic barrier that results in a strong precipitation gradient, with rainfall of more than 2,000 mm/a along the eastern flanks and history of the basin highlights important changes of the depositional system, apparently associated with the transformation from a humid foreland to a fluvially restricted and semi-arid intermontane basin. Similarly, our terrestrial cosmogenic nuclide-derived data indicate an order-of-magnitude decrease in erosion rates at ca. 3 Ma, which suggests a causal link between the onset of uplift-induced semi-arid conditions and decreasing sediment flux into the basin. Ultimately, this dataset may enable a systematic investigation of the long-term causes and consequences of orogenic growth and hydrological changes on spatio-temporal erosion patterns in active mountain areas.

Sediment and Cavitation Erosion Studies through Dam Tunnels

Directory of Open Access Journals (Sweden)

Muhammad Abid

2016-01-01

Full Text Available This paper presents results of sediment and cavitation erosion through Tunnel 2 and Tunnel 3 of Tarbela Dam in Pakistan. Main bend and main branch of Tunnel 2 and outlet 1 and outlet 3 of Tunnel 3 are concluded to be critical for cavitation and sediment erosion. Studies are also performed for increased sediments flow rate, concluding 5 kg/sec as the critical value for sudden increase in erosion rate density. Erosion rate is concluded to be the function of sediment flow rate and head condition. Particulate mass presently observed is reasonably low, hence presently not affecting the velocity and the flow field.

Use of carbon isotope analysis to understand semi-arid erosion dynamics and long-term semi-arid land degradation.

Science.gov (United States)

Turnbull, Laura; Brazier, Richard E; Wainwright, John; Dixon, Liz; Bol, Roland

2008-06-01

Many semi-arid areas worldwide are becoming degraded, in the form of C(4) grasslands being replaced by C(3) shrublands, which causes an increase in surface runoff and erosion, and altered nutrient cycling, which may affect global biogeochemical cycling. The prevention or control of vegetation transitions is hindered by a lack of understanding of their temporal and spatial dynamics, particularly in terms of interactions between biotic and abiotic processes. This research investigates (1) the effects of soil erosion on the delta(13)C values of soil organic matter (SOM) throughout the soil profile and its implications for reconstructing vegetation change using carbon-isotope analysis and (2) the spatial properties of erosion over a grass-shrub transition to increase understanding of biotic-abiotic interactions by using delta(13)C signals of eroded material as a sediment tracer. Results demonstrate that the soils over grass-shrub transitions are not in steady state. A complex interplay of factors determines the input of SOM to the surface horizon of the soil and its subsequent retention and turnover through the soil profile. A positive correlation between event runoff and delta(13)C signatures of eroded sediment was found in all plots. This indicates that the delta(13)C signatures of eroded sediment may provide a means of distinguishing between changes in erosion dynamics over runoff events of different magnitudes and over different vegetation types. The development of this technique using delta(13)C signatures of eroded sediment provides a new means of furthering existing understanding of erosion dynamics over vegetation transitions. This is critical in terms of understanding biotic-abiotic feedbacks and the evolution of areas subject to vegetation change in semi-arid environments. John Wiley & Sons, Ltd

Effect of mechanical properties on erosion resistance of ductile materials

Science.gov (United States)

Levin, Boris Feliksovih

Solid particle erosion (SPE) resistance of ductile Fe, Ni, and Co-based alloys as well as commercially pure Ni and Cu was studied. A model for SPE behavior of ductile materials is presented. The model incorporates the mechanical properties of the materials at the deformation conditions associated with SPE process, as well as the evolution of these properties during the erosion induced deformation. An erosion parameter was formulated based on consideration of the energy loss during erosion, and incorporates the material's hardness and toughness at high strain rates. The erosion model predicts that materials combining high hardness and toughness can exhibit good erosion resistance. To measure mechanical properties of materials, high strain rate compression tests using Hopkinson bar technique were conducted at strain rates similar to those during erosion. From these tests, failure strength and strain during erosion were estimated and used to calculate toughness of the materials. The proposed erosion parameter shows good correlation with experimentally measured erosion rates for all tested materials. To analyze subsurface deformation during erosion, microhardness and nanoindentation tests were performed on the cross-sections of the eroded materials and the size of the plastically deformed zone and the increase in materials hardness due to erosion were determined. A nanoindentation method was developed to estimate the restitution coefficient within plastically deformed regions of the eroded samples which provides a measure of the rebounding ability of a material during particle impact. An increase in hardness near the eroded surface led to an increase in restitution coefficient. Also, the stress rates imposed below the eroded surface were comparable to those measured during high strain-rate compression tests (10sp3-10sp4 ssp{-1}). A new parameter, "area under the microhardness curve" was developed that represents the ability of a material to absorb impact energy. By

A study of erosion rates on salt diapir surfaces in the Zagros Mountains, SE Iran

Czech Academy of Sciences Publication Activity Database

Bruthans, J.; Asadi, N.; Filippi, Michal; Wilhelm, Z.; Zare, M.

2008-01-01

Roč. 53, č. 5 (2008), s. 1079-1089 ISSN 0943-0105 R&D Projects: GA AV ČR(CZ) KJB301110501 Institutional research plan: CEZ:AV0Z30130516 Keywords : salt diapir * weathering residuum * erosion rate Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.026, year: 2008

Using 137 Cs measurements to investigate the influence of erosion and soil redistribution on soil properties.

Science.gov (United States)

Du, P; Walling, D E

2011-05-01

Information on the interaction between soil erosion and soil properties is an important requirement for sustainable management of the soil resource. The relationship between soil properties and the soil redistribution rate, reflecting both erosion and deposition, is an important indicator of this interaction. This relationship is difficult to investigate using traditional approaches to documenting soil redistribution rates involving erosion plots and predictive models. However, the use of the fallout radionuclide (137)Cs to document medium-term soil redistribution rates offers a means of overcoming many of the limitations associated with traditional approaches. The study reported sought to demonstrate the potential for using (137)Cs measurements to assess the influence of soil erosion and redistribution on soil properties (particle size composition, total C, macronutrients N, P, K and Mg, micronutrients Mn, Mo, Fe, Cu and Zn and other elements, including Ti and As). (137)Cs measurements undertaken on 52 soil cores collected within a 7 ha cultivated field located near Colebrooke in Devon, UK were used to establish the magnitude and spatial pattern of medium-term soil redistribution rates within the field. The soil redistribution rates documented for the individual sampling points within the field ranged from an erosion rate of -12.9 t ha(-1) yr(-1) to a deposition rate of 19.2 t ha(-1) yr(-1). Composite samples of surface soil (0-5 cm) were collected immediately adjacent to each coring point and these samples were analysed for a range of soil properties. Individual soil properties associated with these samples showed significant variability, with CV values generally lying in the range 10-30%. The relationships between the surface soil properties and the soil redistribution rate were analysed. This analysis demonstrated statistically significant relationships between some soil properties (total phosphorus, % clay, Ti and As) and the soil redistribution rate, but for

Long-term modeling of soil C erosion and sequestration at the small watershed scale

Energy Technology Data Exchange (ETDEWEB)

Izaurralde, R.C.; Thomson, A.M. [The Joint Global Change Research Institute, 8400 Baltimore Avenue, Suite 201, College Park, MD 20740-2496 (United States); Williams, J.R. [Blacklands Research Center, Texas A and M University, 808 East Blacklands Road, Temple, TX 76502 (United States); Post, W.M. [Oak Ridge National Laboratory, Building 1509, Bethel Valley Road, PO Box 2008 MS6335, Oak Ridge, TN 537831-6335 (United States); McGill, W.B. [College of Science and Management, University of Northern British Columbia, 3333 University Way, Prince George, BC V2N 4Z9 (Canada); Owens, L.B. [North Appalachian Experimental Watershed, USDA-Agricultural Research Station, 28850 SR 621, Coshocton, OH 43812-0488 (United States); Lal, R. [School of Natural Resources Food, Agricultural and Environmental Sciences, The Ohio State University, 422B Kottman Hall, 2021 Coffey Road, Columbus, OH 43210 (United States)

2007-01-15

The soil C balance is determined by the difference between inputs (e.g., plant litter, organic amendments, depositional C) and outputs (e.g., soil respiration, dissolved organic C leaching, and eroded C). There is a need to improve our understanding of whether soil erosion is a sink or a source of atmospheric CO2. The objective of this paper is to discover the long-term influence of soil erosion on the C cycle of managed watersheds near Coshocton, OH. We hypothesize that the amount of eroded C that is deposited in or out of a watershed compares in magnitude to the soil C changes induced via microbial respiration. We applied the erosion productivity impact calculator (EPIC) model to evaluate the role of erosion-deposition processes on the C balance of three small watersheds ({approx}1 ha). Experimental records from the USDA North Appalachian Experimental Watershed facility north of Coshocton, OH were used in the study. Soils are predominantly silt loam and have developed from loess-like deposits over residual bedrock. Management practices in the three watersheds have changed over time. Currently, watershed 118 (W118) is under a corn (Zea mays L.)-soybean (Glycine max [L.] Merr.) no till rotation, W128 is under conventional till continuous corn, and W188 is under no till continuous corn. Simulations of a comprehensive set of ecosystem processes including plant growth, runoff, and water erosion were used to quantify sediment C yields. A simulated sediment C yield of 43 {+-} 22 kg C ha{sup -1} year{sup -1} compared favorably against the observed 31 {+-} 12 kg C ha{sup -1} year{sup -1} in W118. EPIC overestimated the soil C stock in the top 30-cm soil depth in W118 by 21% of the measured value (36.8 Mg C ha{sup -1}). Simulations of soil C stocks in the other two watersheds (42.3 Mg C ha{sup -1} in W128 and 50.4 Mg C ha{sup -1} in W188) were off by <1 Mg C ha{sup -1}. Simulated eroded C re-deposited inside (30-212 kg C ha{sup -1} year{sup -1}) or outside (73{sup -1}79 kg

Using 7Be to document soil erosion on the weed plots

International Nuclear Information System (INIS)

Zhang Bo; Zhang Fengbao; Yang Mingyi

2013-01-01

Be tracing technology was applied to document soil erosion on the bare plot and weed plot, and compae soil erosion rate with the calculated rate. Results indicated that vegetation cover had obvious effect on the estimate of soil erosion rate on the weed plot using 7 Be measurement. Therefore, a factor of vegetation had been introduced into the Walling's model of converting 7 Be activity to soil erosion rate for estimating soil erosion rate on the weed slope surface. It was found that the soil erosion rates calculated by modified model were well close to the measured values on the weed plot, which illustrated that the modified model could be well used to estimate the rates of soil loss on the weed slope surface. These findings provide effective means for further study on the relationship between vegetation cover and soil erosion. (authors)

Effects of Bank Vegetation and Incision on Erosion Rates in an Urban Stream

Directory of Open Access Journals (Sweden)

Emily Arnold

2018-04-01

Full Text Available Changing land-use associated with urbanization has resulted in shifts in riparian assemblages, stream hydraulics, and sediment dynamics leading to the degradation of waterways. To combat degradation, restoration and management of riparian zones is becoming increasingly common. However, the relationship between flora, especially the influence of invasive species, on sediment dynamics is poorly understood. Bank erosion and turbidity were monitored in the Tookany Creek and its tributary Mill Run in the greater Philadelphia, PA region. To evaluate the influence of the invasive species Reynoutria japonica (Japanese knotweed on erosion, reaches were chosen based on their riparian vegetation and degree of incision. Bank pins and turbidity loggers were used to estimate sediment erosion. Erosion calculations based on bank pins suggest greater erosion in reaches dominated by knotweed than those dominated by trees. For a 9.5-month monitoring period, there was 29 cm more erosion on banks that were also incised, and 9 cm more erosion in banks with little incision. Turbidity responses to storm events were also higher (77 vs. 54 NTU (nephelometric turbidity unit in reaches with knotweed, although this increase was found when the reach dominated by knotweed was also incised. Thus, this study linked knotweed to increased erosion using multiple methods.

Ecohydrological Linkages, Multi-scale Processes, Temporal Variability, and Drivers of Change in a Degraded Pinyon-Juniper Watershed: Implications for Erosion Modeling

Science.gov (United States)

Allen, C. D.

2006-12-01

In 1993 long-term research began on the runoff and erosion dynamics of a pinyon-juniper woodland hillslope at Bandelier National Monument in northern New Mexico (USA). In the 1.09 ha Frijolito watershed, erosion has been continuously studied at 3 spatial scales: 1 square meter, about 1000 square meters, and the entire watershed. This site is currently representative of degraded woodlands of pinyon (Pinus edulis) and one-seed juniper (Juniperus monosperma) in this region, exhibiting marked connectivity of exposed bare soil interspaces between tree canopy patches and obvious geomorphic signs of accelerated soil erosion (e.g., pedestalling, actively expanding rill networks). Ecological and land use histories show that this site has undergone a number of dramatic ecohydrological shifts since ca. C.E. 1850, transitioning from: 1) open ponderosa pine (Pinus ponderosa) overstory with limited pinyon-juniper component and substantial herbaceous understory that supported surface fires and constrained soil erosion, to; 2) ponderosa pine with reduced herbaceous cover due to livestock grazing after ca.1870, resulting in collapse of the surface fire regime and increased establishment of young pinyon and juniper trees, to; 3) mortality of all of the ponderosa pine during the extreme drought of the 1950s, leaving eroding pinyon-juniper woodland, to; 4) mortality of all mature pinyon at or above sapling size during the 2002-2003 drought, with juniper now the only dominant woody species. Detailed measurements since 1993 document high rates of soil erosion (> 2.75 Mg/ha/year on average at the watershed scale) that are rapidly stripping the local soils. Long-term observations are needed to distinguish short-term variability from longer term trends, as measurements of runoff and erosion show extreme variability at multiple time scales since 1993. The multi-scale erosion data from the Frijolito watershed reveal little dropoff in erosion rate (g/meter-squared) between the one meter

Dynamics of soil organic carbon and microbial biomass carbon in relation to water erosion and tillage erosion.

Science.gov (United States)

Xiaojun, Nie; Jianhui, Zhang; Zhengan, Su

2013-01-01

Dynamics of soil organic carbon (SOC) are associated with soil erosion, yet there is a shortage of research concerning the relationship between soil erosion, SOC, and especially microbial biomass carbon (MBC). In this paper, we selected two typical slope landscapes including gentle and steep slopes from the Sichuan Basin, China, and used the (137)Cs technique to determine the effects of water erosion and tillage erosion on the dynamics of SOC and MBC. Soil samples for the determination of (137)Cs, SOC, MBC and soil particle-size fractions were collected on two types of contrasting hillslopes. (137)Cs data revealed that soil loss occurred at upper slope positions of the two landscapes and soil accumulation at the lower slope positions. Soil erosion rates as well as distribution patterns of the erosion is the major process of soil redistribution in the gentle slope landscape, while tillage erosion acts as the dominant process of soil redistribution in the steep slope landscape. In gentle slope landscapes, both SOC and MBC contents increased downslope and these distribution patterns were closely linked to soil redistribution rates. In steep slope landscapes, only SOC contents increased downslope, dependent on soil redistribution. It is noticeable that MBC/SOC ratios were significantly lower in gentle slope landscapes than in steep slope landscapes, implying that water erosion has a negative effect on the microbial biomass compared with tillage erosion. It is suggested that MBC dynamics are closely associated with soil redistribution by water erosion but independent of that by tillage erosion, while SOC dynamics are influenced by soil redistribution by both water erosion and tillage erosion.

Decreasing soil erosion rates with evolving land-use techniques in a central European catchment

Science.gov (United States)

Larsen, Annegret; Heckmann, Tobias; Hans-Rudolf, Bork; Alexander, Fuelling

2015-04-01

Agricultural societies around the world have caused accelerated soil erosion. Soil erosion and a decrease in soil fertility may also have caused the abandonment of entire landscapes and the collapse of civilizations. In central Europe, Medieval land-use is thought to have lead to the largest loss of top soil in history, which in turn lead to a malnutrition of the population and abandonment of agricultural land. However, this might be only part of the picture, as people are also able to adapt to changing environmental conditions, including the type of land-use they adopt. Within a catchment in the central European mountain belt, we were able to distinguish the evolution between three main types of land-use techniques between ~ 900 AD and 1950 AD: horticulture, agriculture and shifting cultivation. We were able to relate these techniques with different soil erosion rates, which differ by an order of magnitude, ranging from 0.83 ± 0.09 mm/yr to 1.62 ± 0.17 mm/yr. Using high-resolution surface data and chrono-stratigraphical methods in combination with soil charcoal analysis, we were able to reconstruct past land-use techniques on a local scale. This illustrates that less erosive and more sustainable techniques were developed through time, and hypothesize that people were able to adapt to the less favorable environmental conditions by changing the cultivation techniques. Although cultural adaptation to changing environmental conditions has been extensively discussed, this study is able to quantitatively demonstrate improved soil management with evolving land-use in central Europe.

Use of radioactive fallout cesium-137 to estimate soil erosion on three farms in west central Ohio

International Nuclear Information System (INIS)

Bajracharya, R.M.; Lal, R.; Kimble, J.M.

1998-01-01

Assessment of the impact of soil erosion on productivity and environment quality requires comprehensive and credible estimates of erosion. Measuring concentration of 137 Cs fallout is a relatively simple and rapid technique for determining long-term mean annual rates of soil erosion and deposition. The purpose of this study was to evaluate the potential of the 137 Cs activity-soil depth relationship in estimating soil erosion from arable land in west central Ohio. Thus, soil samples obtained from three to four genetic horizons of four erosion phases at three farms in Clark Co., Ohio, (hereafter called Sites A, B, and C) were analyzed for 137 Cs activity. Relationships between 137 Cs activity and soil depth at undisturbed reference sites were used to calculate the depth of soil eroded and mean annual erosion rates. Cumulative 137 Cs activities ranged from 6.8 mBq g-1 for the severely eroded phase at Site C to 16.6 mBq g-1 for the deposition phase at Site A. These activities corresponded to soil erosion rates of 125.9 Mg ha-1 y-1 for severe to 26.6 Mg ha-1 y-1 for deposition phases. A general trend of increasing soil erosion (by 24 to 85%) from slightly to severely eroded phases was observed although the data were highly variable. Estimated soil erosion rates depended on the regression model used and were more than an order of magnitude higher than those determined using the Revised Universal Soil Loss Equation. Sampling rigorously at small depth increments by means of a core sampler, careful selection of reference sites, and calibration or validation of this technique with other models can improve estimation of soil erosion using 137 Cs. The 137 Cs technique is, however, limited to local scale estimates of erosion because the empirical models are site specific

Erosion reasons and rate on accumulative Polish dune coast caused by the January 2012 storm surge

Directory of Open Access Journals (Sweden)

Tomasz A. Łabuz

2014-03-01

Full Text Available The Polish coast is a non-tidal area; its shores are affected mainly by autumn-winter storm surges. Those of 6 and 14 January 2012 are representative of the forces driving the erosion of normally accumulative sections of coastal dunes, monitored by the author since 1997. The sea level maximum during these two storm surges reached 1.2 to 1.5 m amsl along the Polish coast. Land forms up to 3 m amsl were inundated. Beaches and low parts of the coast up to this height were rebuilt by sea waves attacking the coast for almost 12 days. Quantitative analyses of the morphological dynamics of the coastal dunes are presented for 57 profiles located along the coast. Only those accumulative sections of the Polish coast are analysed where sand accumulation did occur and led to new foredune development. The mean rate of dune erosion was 2.5 m3 per square metre with an average toe retreat of 1.4 m. Erosion understood as dune retreat was greater when a beach was lower (correlation coefficient 0.8. Dune erosion did not occur on coasts with beaches higher than 3.2 m or on lower ones covered by embryo dunes.

Rate and cost of soil erosion in Monkayo, Compostela Valley Province Philippines

Directory of Open Access Journals (Sweden)

Sunshine G. Paulin

2016-01-01

Full Text Available Soil erosion is a major agricultural and environmental problem in the Philippines that is primarily caused by rainfall under upland, subsistence rainfed farming. The study sought to compare the degree of erosion as influenced by different upland tillage systems using soil erosion plots and MUSLE model, and estimate the cost of soil erosion in Monkayo, Compostela Valley. The erosion plots were laid on a 31.45 percent slope with a seasonal rainfall intensity of 2,314 mm. Corn (Zea mays L. planted through conventional tillage generated a mean soil loss of 2.64 t/ha/cropping, which is higher than the reduced tillage with a mean of 1.20 t/ha/cropping. The weighted on-site soil loss was 12 percent lower than the obtained soil erosion using the modified Universal Soil Loss Equation that is 2.97 t/ha. The study developed equations to estimate soil loss (t/ha per seasonal rainfall on three tillage systems using linear regression analysis which are: (1 E= -0.0031+0.0003R, (2 E= -0.0406+0.0011R, and (3 E=0.2249+0.0034R in corn grown on undisturbed land with natural vegetation, corn grown on bare soil through dibble method and corn planted through conventional planting system, respectively. On-site cost of erosion ranged from Php 1,473.42/ha/cropping to Php 1,938.81/ha/cropping. The amount of soil eroded can be attributed to the higher erositivity of rains, higher erodibility of the soil surface, and the poor soil cover.

Pressure and velocity dependence of flow-type cavitation erosion

CSIR Research Space (South Africa)

Auret, JG

1993-12-01

Full Text Available Previous results on the influence of water pressure and velocity on flow-type cavitations erosion, i.e. an increase in erosion rate with increasing velocity and peaking of erosion rate as a function of pressure, were confirmed by measurements with a...

An overview of erosion corrosion models and reliability assessment for corrosion defects in piping system

International Nuclear Information System (INIS)

Srividya, A.; Suresh, H.N.; Verma, A.K.; Gopika, V.; Santosh

2006-01-01

Piping systems are part of passive structural elements in power plants. The analysis of the piping systems and their quantification in terms of failure probability is of utmost importance. The piping systems may fail due to various degradation mechanisms like thermal fatigue, erosion-corrosion, stress corrosion cracking and vibration fatigue. On examination of previous results, erosion corrosion was more prevalent and wall thinning is a time dependent phenomenon. The paper is intended to consolidate the work done by various investigators on erosion corrosion in estimating the erosion corrosion rate and reliability predictions. A comparison of various erosion corrosion models is made. The reliability predictions based on remaining strength of corroded pipelines by wall thinning is also attempted. Variables in the limit state functions are modelled using normal distributions and Reliability assessment is carried out using some of the existing failure pressure models. A steady state corrosion rate is assumed to estimate the corrosion defect and First Order Reliability Method (FORM) is used to find the probability of failure associated with corrosion defects over time using the software for Component Reliability evaluation (COMREL). (author)

Using {sup 137}Cs measurements to investigate the influence of erosion and soil redistribution on soil properties

Energy Technology Data Exchange (ETDEWEB)

Du, P. [School of Geography, Beijing Normal University, Beijing (China); Geography, College of Life and Environmental Sciences, University of Exeter, Amory Building, Rennes Drive, Exeter, EX4 4RJ, Devon (United Kingdom); Walling, D.E., E-mail: d.e.walling@exeter.ac.u [Geography, College of Life and Environmental Sciences, University of Exeter, Amory Building, Rennes Drive, Exeter, EX4 4RJ, Devon (United Kingdom)

2011-05-15

Information on the interaction between soil erosion and soil properties is an important requirement for sustainable management of the soil resource. The relationship between soil properties and the soil redistribution rate, reflecting both erosion and deposition, is an important indicator of this interaction. This relationship is difficult to investigate using traditional approaches to documenting soil redistribution rates involving erosion plots and predictive models. However, the use of the fallout radionuclide {sup 137}Cs to document medium-term soil redistribution rates offers a means of overcoming many of the limitations associated with traditional approaches. The study reported sought to demonstrate the potential for using {sup 137}Cs measurements to assess the influence of soil erosion and redistribution on soil properties (particle size composition, total C, macronutrients N, P, K and Mg, micronutrients Mn, Mo, Fe, Cu and Zn and other elements, including Ti and As). {sup 137}Cs measurements undertaken on 52 soil cores collected within a 7 ha cultivated field located near Colebrooke in Devon, UK were used to establish the magnitude and spatial pattern of medium-term soil redistribution rates within the field. The soil redistribution rates documented for the individual sampling points within the field ranged from an erosion rate of -12.9 t ha{sup -1} yr{sup -1} to a deposition rate of 19.2 t ha{sup -1} yr{sup -1}. Composite samples of surface soil (0-5 cm) were collected immediately adjacent to each coring point and these samples were analysed for a range of soil properties. Individual soil properties associated with these samples showed significant variability, with CV values generally lying in the range 10-30%. The relationships between the surface soil properties and the soil redistribution rate were analysed. This analysis demonstrated statistically significant relationships between some soil properties (total phosphorus, % clay, Ti and As) and the soil

Medication-related dental erosion: a review.

Science.gov (United States)

Thomas, Manuel S; Vivekananda Pai, A R; Yadav, Amit

2015-10-01

Dental erosion has become a major problem that affects the long-term health of the dentition. Among the various potential causes for erosive tooth wear, the different drugs prescribed for patients may be overlooked. Several therapeutic medications can directly or indirectly be associated with dental erosion. It is the responsibility of oral health providers to make both patients and colleagues aware of drugs that may contribute to this condition. Therefore, the purpose of this discussion is to provide an overview of the various therapeutic medications that can be related to tooth erosion. The authors also include precautionary measures-summarized as The 9 Rs-to avoid or at least reduce medication-induced erosion.

Does introduced fauna influence soil erosion? A field and modelling assessment.

Science.gov (United States)

Hancock, G R; Lowry, J B C; Dever, C; Braggins, M

2015-06-15

Pigs (Sus scrofa) are recognised as having significant ecological impacts in many areas of the world including northern Australia. The full consequences of the introduction of pigs are difficult to quantify as the impacts may only be detected over the long-term and there is a lack of quantitative information on the impacts of feral pigs globally. In this study the effect of feral pigs is quantified in an undisturbed catchment in the monsoonal tropics of northern Australia. Over a three-year period, field data showed that the areal extent of pig disturbance ranged from 0.3-3.3% of the survey area. The mass of material exhumed through these activities ranged from 4.3 t ha(-1) yr(-1) to 36.0 t ha(-1) yr(-1). The findings demonstrate that large introduced species such as feral pigs are disturbing large areas as well as exhuming considerable volumes of soil. A numerical landscape evolution and soil erosion model was used to assess the effect of this disturbance on catchment scale erosion rates. The modelling demonstrated that simulated pig disturbance in previously undisturbed areas produced lower erosion rates compared to those areas which had not been impacted by pigs. This is attributed to the pig disturbance increasing surface roughness and trapping sediment. This suggests that in this specific environment, disturbance by pigs does not enhance erosion. However, this conclusion is prefaced by two important caveats. First, the long term impact of soil disturbance is still very uncertain. Secondly, modelling results show a clear differentiation between those from an undisturbed environment and those from a post-mining landscape, in which pig disturbance may enhance erosion. Copyright © 2015. Published by Elsevier B.V.

Saliva composition in three selected groups with normal stimulated salivary flow rates, but yet major differences in caries experience and dental erosion.

Science.gov (United States)

Bardow, Allan; Lykkeaa, Joan; Qvist, Vibeke; Ekstrand, Kim; Twetman, Svante; Fiehn, Niels-Erik

2014-08-01

It was hypothesized that, by comparing matched subjects with major differences in these dental diseases, but yet normal saliva flow rates, it would be possible to obtain data on the effect of saliva composition on dental disease isolated from the effect of the flow rate. Thus, the aim of the study was to compare the major physicochemical characteristics of stimulated whole saliva in three groups of 85 subjects, each with normal saliva flow rates and at least 24 remaining teeth. A group with very little dental disease (healthy), a group with dental erosion (erosion) and a group with very high caries experience (caries) were chosen. Furthermore, the aim was to determine whether differences among groups could also be found on an individual level. Although it was not possible to retrieve three groups whose members were completely identical, the present study points in the direction that, on a group level, subjects with very little dental disease seemed to have a more favorable physicochemical saliva composition with respect to higher calcium, phosphate, bicarbonate, pH, degree of saturation with respect to hydroxyapatite and a lower critical pH (p dental erosion (p dental caries and erosion in single individuals.

PENGKLASTERAN EROSI DI SUB DAS NGRANCAH KULONROGO (Soil Erosion Rates Clustering of Ngrancah Sub Watershed, Kulon Progo

Directory of Open Access Journals (Sweden)

Ambar Kusumandari

2012-03-01

Full Text Available ABSTRAK Penelitian ini dilakukan di Sub DAS Ngrancah yang merupakan daerah tangkapan air Waduk Sermo. Luas wilayah penelitian ini sekitar 2.200 ha. Mayoritas lahan di Sub DAS Ngrancah tergolong kritis yang ditunjukkan oleh tingginya tingkat erosi. Dengan demikian, wilayah ini sangat mendesak untuk dapat dikelola dengan benar agar degradasi lahan dapat dihambat. Untuk memprediksi erosi, diterapkan Model USLE, dengan rumus: A = RKLSCP. Wilayah studi dapat dipilahkan menjadi 77 unit lahan. Sampel tanah diambil dari seluruh unit lahan, demikian pula pengamatan lereng, vegetasi, dan penerapan konservasi tanah. Untuk menganalisis data digunakan analisis kluster. Hasil penelitian menunjukkan bahwa tingkat erosi bervariasi dari yang paling rendah sebesar 2,54 ton/ha/th sampai dengan yang tertinggi sebesar 489,30 ton/ha/th. Sekitar 68% wilayah studi termasuk dalam kelas erosi sedang dan sekitar 15% wilayah studi termasuk dalam kelas erosi tinggi. Pengklasteran unit lahan secara statistik menunjukkan bahwa pada jarak klaster terpendek terbentuk 8 klaster tingkat erosi. Uji diskriminan menunjukkan bahwa faktor K (erodibilitas dan P (praktek konservasi tanah dan air merupakan faktor yang paling dominan untuk terbentuknya klaster-klaster tersebut. Hasil penelitian ini diharapkan bermanfaat dalam merancang teknik konservasi tanah dan air untuk menangani erosi di Sub DAS Ngrancah. ABSTRACT The research was carried out at Ngrancah Sub Watershed which is located at the upper area of Sermo Dam and covers an area of almost 2.200 hectares.  The area is mostly critical showed by the high rates of erosion, so, it is  urgently required to manage properly in order to combat  land degradation. In this research, to study the erosion rates of the area, the USLE method was used, i.e. A = RxKxLSxCxP. The area was devided into 77 land units and the soil samples were taken from each land units as well as the observation of slopes, vegetation and soil conservation practices

Molybdenum erosion measurements in Alcator C-Mod

Energy Technology Data Exchange (ETDEWEB)

Wampler, W.R. [Sandia National Labs., Albuquerque, NM (United States); LaBombard, B.; Lipshultz, B.; Pappas, D.; Pitcher, C.S. [Massachusetts Inst. of Tech., Cambridge, MA (United States); McCracken, G.M. [JET Joint Undertaking, Abingdon (United Kingdom)

1998-05-01

Erosion of molybdenum was measured on a set of 21 tiles after a run campaign of 1,090 shots in the Alcator C-Mod tokamak. The net erosion of molybdenum, was determined from changes in the depth of a thin chromium marker layer measured by Rutherford backscattering. Net Mo erosion was found to be approximately 150 nm near the outer divertor strike point, and much less everywhere else. Gross erosion rates by sputtering were estimated using ion energies and fluxes obtained from Langmuir probe measurements of edge-plasma conditions. Predicted net erosion using calculated gross erosion with prompt redeposition and measured net erosion agree within a factor of 3. Sputtering by boron and molybdenum impurities dominates erosion.

Three Gorges Reservoir Area: soil erosion under natural condition vs. soil erosion under current land use

Science.gov (United States)

Schönbrodt, Sarah; Behrens, Thorsten; Scholten, Thomas

2010-05-01

Apparently, the current most prominent human-induced example for large scale environmental impact is the Three Gorges Dam in China. The flooding alongside the Yangtze River, and its tributaries results in a vast loss of settlement and farmland area with productive, fertile valley soils. Due to the associated high land use dynamic on uphill-sites, the soil resources are underlying high land use pressure. Within our study, the soil erosion under natural conditions is compared to the soil erosion under current land use after the impoundment. Both were modeled using the empirical Universal Soil Loss Equation (USLE) which is able to predict long-term annual soil loss with limited data. The database consists of digital terrain data (45 m resolution DEM, erosive slope length based on Monte-Carlo-Aggregation according to Behrens et al. (2008)), field investigations of recent erosion forms, and literature studies. The natural disposition to soil erosion was calculated considering the USLE factors R, S, and K. The soil erosion under current land use was calculated taking into account all USLE factors. The study area is the catchment of the Xiangxi River in the Three Gorges Reservoir area. Within the Xiangxi Catchment (3,200 km²) the highly dynamic backwater area (580 km²), and two micro-scale study sites (Xiangjiaba with 2.8 km², and Quyuan with 88 km²) are considered more detailed as they are directly affected by the river impoundment. Central features of the Xiangxi Catchment are the subtropical monsoon climate, an extremely steep sloping relief (mean slope angle 39°, SD 22.8°) artificially fractured by farmland terraces, and a high soil erodibility (mean K factor 0.37, SD 0.13). On the catchment scale the natural disposition to soil erosion makes up to mean 518.0 t ha-1 a-1. The maximum potential soil loss of 1,730.1 t ha-1 a-1 under natural conditions is reached in the Quyuan site (mean 635.8 t ha-1 a-1) within the backwater area (mean 582.9 t ha-1 a-1). In the

Extrusion and erosion of bentonite buffer material in a flow-through, horizontal, artificial fracture system

International Nuclear Information System (INIS)

Schatz, Timothy; Kanerva, Noora; Martikainen, Jari

2012-01-01

Document available in extended abstract form only. One scenario of interest for the long-term safety assessment of a spent nuclear fuel repository involves the loss of bentonite buffer material through contact with dilute groundwater at a transmissive fracture interface [SKB 2011, Posiva 2012]. In order to simulate the potential extrusion/erosion behaviour of bentonite buffer material in such an environment, a series of small-scale, flow-through, artificial fracture experiments were performed in which swelling clay material could extrude/erode into a well defined, system (see Figure 1). The fracture dimensions were 24 cm (length) x 24 cm (width) x 1 mm (aperture) and the compacted sample dimensions were 2 cm (height) x 2 cm (diameter). Extrusion/erosion effects were analysed against solution chemistry (salt concentration and composition), material composition (sodium montmorillonite and admixtures with calcium montmorillonite), and flow velocity. No erosion was observed for sodium montmorillonite against solution compositions from 10 to 0.5 g/L NaCl. Comparatively, most reports in the literature indicate that a concentration of 0.5 g/L NaCl (8.6 mM) is below, in some cases well below, the (experimentally observed) critical coagulation concentration (CCC) for the colloidal sodium montmorillonite/sodium chloride system [Garcia-Garcia et al. 2007]. It was also the case that no erosion was observed for 50/50 calcium/sodium montmorillonite against 0.5 g/L NaCl. Overall, the results of the flow-through, artificial fracture tests, indicate stability to erosion down to a dilute concentration range between 8 to 4 mM NaCl for both sodium and 50/50 calcium/sodium montmorillonite. These limits compare favorably to the erosion stability limits observed by Birgersson et al. [2009] in the case of the latter material but less so for the former. A number of tests were conducted for which measurable erosion was observed. The calculated mass loss rates for these tests, expressed in

The Influence of Wildfire on Long-Term Erosion: Insights from the Jemez Mountains, NM and the Western USA

Science.gov (United States)

Fitch, E. P.; Meyer, G. A.

2017-12-01

and density; potent climatic influence on the latter makes it difficult to generalize about how strongly fire drives long-term erosion rates, as even local aspect is important. Also, our data represent interglacial environments that are uncommon over the Quaternary, such that extrapolation of fire's importance beyond the last 104 yr is unwarranted.

[US Geological Survey research in radioactive waste disposal, fiscal year 1980:] Tectonics, seismicity, volcanism, and erosion rates in the southern Great Basin

International Nuclear Information System (INIS)

Carr, W.J.; Rogers, A.M.

1982-01-01

The objective is to assess the potential for faulting, damaging earthquakes, recurrence of volcanism, and local acceleration of erosion in parts of the southern Great Basin. The following approaches are being used: (1) investigating the rate, intensity, and distribution of faulting during approximately the last 25 m.y., with emphasis on the last 10 m.y.; (2) monitoring and interpreting present seismicity; (3) studying the history of volcanism; and (4) evaluating past rates of erosion and deposition. Progress is reported

Variability of Rainfall Erosivity and Erosivity Density in the Ganjiang River Catchment, China: Characteristics and Influences of Climate Change

Directory of Open Access Journals (Sweden)

Xianghu Li

2018-02-01

Full Text Available Soil erosion is one of the most critical environmental hazards in the world. Understanding the changes in rainfall erosivity (RE and erosivity density (ED, as well as their affecting factors, at local and catchment scales in the context of climate warming is an important prerequisite of soil erosion prevention and soil loss risk assessment. The present study identified the variability and trends of RE and ED in terms of both time and space in the Ganjiang River catchment over the period of 1960–2012, and also analyzed and discussed the impact of climate change. The results show that RE and ED in the catchment had great monthly variations and high year-to-year variability. Both presented long-term increasing trends over the entire study period. The highest RE and ED were observed in June and in the eastern and northeast parts of the catchment, which indicated that June was the most susceptible month for soil erosion in this area and the lower reaches of the Ganjiang River was the riskiest area for soil erosion. Finally, the East Asian summer monsoon and climate change were highly correlated with changes in RE and ED.

Sand transport, erosion and granular electrification

DEFF Research Database (Denmark)

Merrison, J.P.

2012-01-01

is expanding our current understanding and outline the areas of advancement needed in the future. Presentation is made of current models for wind driven detachment/entrainment and the transport rates of sand and dust, including the effects of contact induced grain electrification. This ubiquitous phenomenon...... can affect grain transport through the generation of intense electric fields and processes of electrostatic assembly. Importantly the transport of sand is characterized by saltation, which is known to be an active process for erosion and therefore a source for dust and sand formation. Using novel...... erosion simulation techniques the link between grain transport rates and erosion rates has been quantified. Furthermore this can be linked to production rates for dust and has been associated with chemical and mineral alteration through a process of mechanical activation of fractured surfaces. This work...

High rate of vaginal erosions associated with the mentor ObTape.

Science.gov (United States)

Yamada, Brian S; Govier, Fred E; Stefanovic, Ksenija B; Kobashi, Kathleen C

2006-08-01

The transobturator tape method is a newer surgical technique for the treatment of stress urinary incontinence. Limited data exist related to complications with this approach or the types of mesh products used. We report our experience with vaginal erosions associated with the Mentor ObTape and American Medical Systems Monarc transobturator slings. Beginning in December 2003 selected female patients with anatomic urinary incontinence were prospectively followed after placement of the Mentor ObTape. Beginning in January 2004 we also began using the American Medical Systems Monarc in similar patients. Patients were admitted overnight after surgery, discharged on oral antibiotics, and seen in the clinic at 6 weeks postoperatively. A total of 67 patients have undergone placement of the Mentor ObTape and 9 of those patients (13.4%) have had vaginal extrusions of the sling. Eight patients reported a history of persistent vaginal discharge. One patient presented initially to an outside facility with a left thigh abscess tracking to the left inguinal incision site. Each patient was taken back to the operating room for mesh removal. A total of 56 patients have undergone placement of the AMS Monarc and none have had any vaginal erosions. Our high rate of vaginal extrusion using the ObTape has led us to discontinue the use of this product in our institution. Continued followup of all of these patients will be of critical importance.

Coupling of physical erosion and chemical weathering after phases of intense human activity

Science.gov (United States)

Schoonejans, Jerome; Vanacker, Veerle; Opfergelt, Sophie; Ameijeiras-Mariño, Yolanda; Kubik, Peter W.

2014-05-01

Anthropogenic disturbance of natural vegetation profoundly alters the lateral and vertical fluxes of soil nutrients and particles at the land surface. Human-induced acceleration of soil erosion can thereby result in an imbalance between physical erosion, soil production and chemical weathering. The (de-)coupling between physical erosion and chemical weathering in ecosystems with strong anthropogenic disturbances is not yet fully understood, as earlier studies mostly focused on natural ecosystems. In this study, we explore the chemical weathering intensity for four study sites located in the Internal Zone of the Spanish Betic Cordillera. Most of the sites belong to the Nevado-Filabres complex, but are characterized by different rates of long-term exhumation, 10Be catchment-wide denudation and hill slope morphology. Denudation rates are generally low, but show large variation between the three sites (from 23 to 246 mm kyr-1). The magnitude of denudation rates is consistent with longer-term uplift rates derived from marine deposits, fission-track measurements and vertical fault slip rates. Two to three soil profiles were sampled per study site at exposed ridge tops. All soils overly fractured mica schist, and are very thin (< 60cm). In each soil profile, we sampled 5 depth slices, rock fragments and the (weathered) bedrock. In total, 38 soil and 20 rock samples were analyzed for their chemical composition. The chemical weathering intensity is constrained by the Chemical Depletion Fraction that is based on a chemical mass balance approach using Zr as an immobile element. Chemical weathering accounts for 5 to 35% of the total mass lost due to denudation. We observe systematically higher chemical weathering intensities (CDFs) in sites with lower denudation rates (and vice versa), suggesting that weathering is supply-limited. Our measurements of soil elemental losses from 10 soil profiles suggest that the observed variation in chemical weathering is strongly associated

Immunohistochemical Study of p53 Expression in Patients with Erosive and Non-Erosive Oral Lichen Planus

Science.gov (United States)

Shiva, Atena; Zamanian, Ali; Arab, Shahin; Boloki, Mahsa

2018-01-01

Statement of the Problem: Oral lichen planus is a common mucocutaneous lesion with a chronic inflammatory process mediated by immune factors while a few cases of the disease become malignant. Purpose: This study aimed to determine the frequency of p53 marker as a tumor suppressor in patients with erosive and non-erosive oral lichen planus (OLP) by using immunohistochemical methods. Materials and Method: This descriptive cross-sectional study investigated the p53 expression in 16 erosive OLP, 16 non-erosive OLP samples, and 8 samples of normal oral mucosa through immunohistochemistry. The percentage of stained cells in basal and suprabasal layers, and inflammatory infiltrate were graded according to the degree of staining; if 0%, 50% of the cells were stained, they were considered as (-), (+), (++), (+++) and (++++), respectively. The obtained data was statistically analyzed and compared by using Chi square and Fisher’s exact test. Results: The mean percentage of p53 positive cells in erosive OLP (34.5±14.2) was considerably higher than that in non-erosive OLP (23.8±10.4) and normal mucosa (17.5±17). There was a significant difference among the three groups of erosive, non-erosive and control in terms of staining intensity. No significant difference existed between the patients’ age and sex in the two OLP groups. Conclusion: The increased incidence of p53 from normal mucosa to erosive OLP indicated the difference between biological behavior of erosive and non-erosive OLP. It can be claimed that the erosive OLP has great premalignant potential compared with the non-erosive one.

THE INFLUENCE OF CONVERSION MODEL CHOICE FOR EROSION RATE ESTIMATION AND THE SENSITIVITY OF THE RESULTS TO CHANGES IN THE MODEL PARAMETER

Directory of Open Access Journals (Sweden)

Nita Suhartini

2010-06-01

Full Text Available A study of soil erosion rates had been done on a slightly and long slope of cultivated area in Ciawi - Bogor, using 137Cs technique. The objective of the present study was to evaluate the applicability of the 137Cs technique in obtaining spatially distributed information of soil redistribution at small catchment. This paper reports the result of the choice of conversion model for erosion rate estimates and the sensitive of the changes in the model parameter. For this purpose, small site was selected, namely landuse I (LU-I. The top of a slope was chosen as a reference site. The erosion/deposit rate of individual sampling points was estimated using the conversion models, namely Proportional Model (PM, Mass Balance Model 1 (MBM1 and Mass Balance Model 2 (MBM2. A comparison of the conversion models showed that the lowest value is obtained by the PM. The MBM1 gave values closer to MBM2, but MBM2 gave a reliable values. In this study, a sensitivity analysis suggest that the conversion models are sensitive to changes in parameters that depend on the site conditions, but insensitive to changes in  parameters that interact to the onset of 137Cs fallout input.   Keywords: soil erosion, environmental radioisotope, cesium

Soil erosion in Slovene Istria

Directory of Open Access Journals (Sweden)

Matjaž Mikoš

2009-12-01

Full Text Available From the end of nineties of the 20th century, intense hydrologic and geomorphologic research is taking place in the Slovene Istria. As a part of this research also studies on soil erosion were undertaken in the period from 2005 to 2008. The field measurements were under taken onclosed 1m2 large erosion plots under three different land uses (on bare soils in an olive grove, on an overgrown meadow, in a forest, placed south of the Marezige village in the Rokava River basin.We show weekly measurements of surface erosion (interrill erosion for the period of 13 months (the end of March 2005 – the end of April 2006, as well as monthly and seasonal averages together with selected linear statistical correlations between soil erosion and weather parameters.From May 2005 to April 2006 the interrill erosion on bare soils in an olive grove with an inclination of 5.5° amounted to 9013 g/m2 (90 t/ha that corresponds to surface lowering rate of 8.5 mm/yr; on an overgrown meadow with an inclination of 9.4° it amounted to 168 g/m2 (1,68 t/ha that corresponds to surface lowering rate of 0.16 mm//yr; and in a forest with an inclination of 7.8° it amounted to 391 g/m2 (3,91 t/ha and in a forest with an inclination of 21.4° it amounted to 415 g/m2 (4,15 t/ha, respectively, that corresponds to surface lowering rate of 0.4 mm/yr.

Bank erosion along the dam-regulated lower Roanoke River, North Carolina

Science.gov (United States)

Hupp, C.R.; Schenk, E.R.; Richter, J.M.; Peet, Robert K.; Townsend, Phil A.

2009-01-01

Dam construction and its impact on downstream fluvial processes may substantially alter ambient bank stability and erosion. Three high dams (completed between 1953 and 1963) were built along the Piedmont portion of the Roanoke River, North Carolina; just downstream the lower part of the river flows across largely unconsolidated Coastal Plain deposits. To document bank erosion rates along the lower Roanoke River, >700 bank-erosion pins were installed along 66 bank transects. Additionally, discrete measurements of channel bathymetry, turbidity, and presence or absence of mass wasting were documented along the entire study reach (153 km). A bank-erosion- floodplain-deposition sediment budget was estimated for the lower river. Bank toe erosion related to consistently high low-flow stages may play a large role in increased mid- and upper-bank erosion. Present bank-erosion rates are relatively high and are greatest along the middle reaches (mean 63 mm/yr) and on lower parts of the bank on all reaches. Erosion rates were likely higher along upstream reaches than present erosion rates, such that erosion-rate maxima have since migrated downstream. Mass wasting and turbidity also peak along the middle reaches; floodplain sedimentation systematically increases downstream in the study reach. The lower Roanoke River isnet depositional (on floodplain) with a surplus of ??2,800,000 m3yr. Results suggest that unmeasured erosion, particularly mass wasting, may partly explain this surplus and should be part of sediment budgets downstream of dams. ?? 2009 The Geological Society of America.

Experiments on Erosion of Mud from the Danish Wadden Sea

DEFF Research Database (Denmark)

Johansen, C.; Larsen, Torben; Petersen, O.

1994-01-01

Experiments on erosion and consolidation of natural cohesive sediments from the harbour of Esbjerg located in the Danish Watten Sea were conducted using a rotating annular flume. The objective of the paper is to describe the erosion rate of deposited beds and relate the erosion rate...

The barley straw residues avoid high erosion rates in persimmon plantations. Eastern Spain

Science.gov (United States)

Cerdà, Artemi; González Pelayo, Óscar; Giménez-Morera, Antonio; Jordán, Antonio; Novara, Agata; Pereira, Paulo; Mataix-Solera, Jorge

2015-04-01

World persimmon production is 4 Millions tones and China produce more than 80 % of the total world yield. Korea and Japan are the second and the third producers respectively with 0.4 and 0.2 millions tones, and all three Asian countries concentrate more than 95 % of the world production. Spain produce less than 0.1 million tones but there is a sudden increase in new plantations due to the high prices and the new marked developed in Europe, Brazil and Arabic countries. The new chemically managed and highly mechanized plantations in Eastern Spain are using high doses of herbicides and the lack of vegetation is triggering high erosion rates. This paper aims to contribute with information about the soil losses on this new persimmon plantations and to develop strategies to reduce the soil and water losses. A 15 years old plantation of persimmon (Dyospirus lotus) was selected in Eastern Spain (Canals Municipality, La Costera District) to measure the soil losses on No-Tillage bare (herbicide treatments) management and on barley straw covered plots. The straw cover was applied 3 days before the expereriments at at doses that cover more than 50 % of the soil surface using 75 gr of straw per m2. Rainfall simulations under 55 mm h-1 rainfall intensity during one hour on 0.25 m2 plots were carried out on plots paired plots: bare and covered with straw. The measurements were carried out during July 2014 on paired plots, under very dry soil moisture contents ranging from 4.65 to 7.87 %. The results show that the 3% cover of vegetation of the control plots moved to more than 60% due to the application of the straw. This induced a delayed ponding (from 60 to 309 seconds) and surface runoff (from 262 to 815 seconds) and runoff outlet (418 to 1221 seconds). The runoff coefficients moved from 60 % in the control plots to 29 % in the straw covered and the runoff sediment concentration was dramatically reduced from 11 to 1 g l-1. The total soil losses were higher that 1 Kg per plot in

X-ray diagnosis of erosive gastritis

International Nuclear Information System (INIS)

Taskov, A.; Krastin, A.

1993-01-01

A series of 602 patients are studied according to a standard protocol including double contrast examination, taking films with dosed compression and complete filling (accordingly 3+3+1 radiographs). A barium suspension at concentration 200.0 BaSO 4 in 100 ml water is used as a positive contrast medium, and effervescent powder or pills - as a negative contrast. Erosive gastritis is diagnosed in 48 patients (7.9%) of which 38 present complete erosions (79.2%), 6 (12.6%) - incomplete, and 4 (8.3%) - mixed erosions. In 35 cases (72.9%) erosions are differentiated in double-contrast films, while in 21 (43.8%) - in those with compression. The advantage of the double contrast technique consists in visualization of erosions of the body of the stomach and discovering of incomplete erosions. In 483 patients a comparative assessment is done of the X-ray and endoscopic findings. There are recorded 5 false-positive and 25 false-negative radiological results. The sensitivity of the X-ray study in terms of erosive gastritis amounts to 59.7%. 15 refs., 4 figs. (orig.)

The success of headwater rehabilitation towards gully erosion control

Science.gov (United States)

Frankl, Amaury; Poesen, Jean; Nyssen, Jan

2017-04-01

The ill-management of headwaters has frequently shown to have adverse effects on both humans and the environment. Historical examples often refer to altered hydrological conditions and stream incision resulting from deforestation. Agricultural expansion and intensification - often accompanied with land reforms in the 20th century - also showed to severely impact the fluvial environment, with stream incision and gully erosion hazards increasingly affecting many headwater areas around the world. To counter this, many regions have adopted improved management schemes aiming at restoring the physical, biological and hydrological integrity of the soil- and landscape. In terms of hydrogeomorpology, the objective was to minimize dynamics to a lower level so that runoff, sediment and pollutant transfers do not cause danger to human life, environmental/natural resources deterioration or economic stress. Therefore, much attention was given to the rehabilitation and re-naturalization of headwater streams and gullies, which are the conduits of these transfers. This is done in both indirect and direct ways, i.e. reducing the delivery of runoff and sediment to the gullies and interventions in the incised channels. Although much has been published on gully erosion development and control, few studies assess the success of gully rehabilitation on the mid- to long term or confront results against the gully life-cycle. The latter refers to the rate law in fluvial geomorphology, whereby gully morphological changes (increases in length, area, volume) are initially rapid, followed by a much slower development towards a new equilibrium state. Here, we present a review of headwater rehabilitation measures and their success towards gully erosion control. By confronting this to the life-cycle of a gully, we also want to shed light on our understanding of when and where gully erosion control needs to be applied; making land management more efficient and effective. Keywords: land

Corneal erosions, bacterial contamination of contact lenses, and microbial keratitis.

Science.gov (United States)

Willcox, Mark D P; Naduvilath, Thomas J; Vaddavalli, Pravin K; Holden, Brien A; Ozkan, Jerome; Zhu, Hua

2010-11-01

To estimate the rate of corneal erosion coupled with gram-negative bacterial contamination of contact lenses and compare this with the rate of microbial keratitis (MK) with contact lenses. The rate of corneal erosion and contact lens contamination by gram-negative bacteria were calculated from several prospective trials. These rates were used to calculate the theoretical rate of corneal erosion happening at the same time as wearing a contact lens contaminated with gram-negative bacteria. This theoretical rate was then compared with the rates of MK reported in various epidemiological and clinical trials. Corneal erosions were more frequent during extended wear (0.6-2.6% of visits) compared with daily wear (0.01-0.05% of visits). No corneal erosions were observed for lenses worn on a daily disposable basis. Contamination rates for lenses worn on a daily disposable basis were the lowest (2.4%), whereas they were the highest for low Dk lenses worn on an extended wear basis (7.1%). The estimated rate of corneal erosions occurring at the same time as wearing lenses contaminated with gram-negative bacteria was the lowest during daily wear of low Dk lenses (1.56/10,000 [95% CI: 0.23-10.57]) and the highest during extended wear of high Dk lenses (38.55/10,000 [95% CI: 24.77-60.04]). These rates were similar in magnitude to the rates reported for MK of different hydrogel lenses worn on differing wear schedules. The coincidence of corneal erosions during lens wear with gram-negative bacterial contamination of lenses may account for the relative incidence of MK during lens wear with different lens materials and modes of use.

[Sediment transport characteristics at different erosion stages for non-hardened roads of the Shenfu Coalfield, west China].

Science.gov (United States)

Guo, Ming-ming; Wang, Wen-long; Li, Jian-ming; Huang, Peng-fei; Zhu, Bao-cai; Wang, Zhen; Luo, Ting

2015-02-01

Non-hardened roads formed in the production of the Shenfu Coalfield have a unique condition of underlying surface. The road surface is composed of a regolith layer with a certain thickness resulted from long-term rolling and thus, is characterized by weakened anti-scourabilty and anti-erodibility. In contrast, soil layer below the regolith has a higher bulk density and anti-erodibility. The processes of soil erosion on the non-hardened roads exhibit some differences under rainfall condition. The process of sediment transport and the relationship between sediment transport rate and erosion factors at different erosion stages were studied on non-hardened roads with slope degrees ranging from 3° to 12° (3°, 6°, 9°, 12°) by a field experiment under artificial rainfall. Results showed that the first peak of sediment transport on the regolith surface was observed at the sheet erosion stage. Sheet erosion occurred only at 3° slope degree, with an average variation coefficient of 0.07 for sediment transport rate. Rills in every testing began to develop at slope degrees of 6° to 12° about 15 min after runoff initiation. At the sheet erosion stage, the process of sediment transport fluctuated considerably at rainfall intensities of > 1.5 mm · min(-1), but the differences in its variation were little at the three slope degrees, with average variation coefficients of 0.20, 0.19 and 0.16, respectively. Rainfall intensity had a more significant impact on sediment transport rate than slope degree. The process of sediment transport at the rill erosion stage fluctuated, but the fluctuation was obviously smaller than that at the sheet erosion stage, with average variation coefficients of 0.05, 0.09 and 0.10 at the three slope degrees. Many wide and shallow rills evolved at the rill erosion stage. The sediment transport rate could be well predicted by a power function of rainfall intensity and slope degree at the sheet and rill erosion stages. The stable sediment transport

An appraisal of river erosion mitigation in the Niger Delta

International Nuclear Information System (INIS)

Aban, T. K. S.; Omuso, W. O.

1999-01-01

River erosion processes in the Niger Delta and the effectiveness of locally applied remedial measures is appraised, using information on channel geometry, flow velocity distribution, soil type, stratification, bank height and steepness, state of compaction, together with pool level variation in river channels. High flow velocity and bank height were identified as the major erosion causative factors. Local responses towards erosion mitigation have involved structural methods to varying degree of success. River training has been recommended as a long - term regional approach to mitigate river bank erosion. However, in the short -term revetments, concrete and sheets piles may be applied cautiously

The influence of material hardness on liquid droplet impingement erosion

International Nuclear Information System (INIS)

Fujisawa, Nobuyuki; Yamagata, Takayuki; Takano, Shotaro; Saito, Kengo; Morita, Ryo; Fujiwara, Kazutoshi; Inada, Fumio

2015-01-01

Highlights: • Liquid droplet impingement erosion is studied for various metal materials. • Average power dependency on droplet velocity is found as 7. • Power dependency on Vickers hardness is found as −4.5. • An empirical formula is constructed for erosion rates of metal materials. • Predicted erosion rate is well correlated with experiment within a factor of 1.5. - Abstract: This paper describes the experimental study on the liquid droplet impingement erosion of metal materials to understand the influence of material hardness on the erosion rate. The experiment is carried out using a water spray jet apparatus with a condition of relatively thin liquid film thickness. The metal materials tested are pure aluminum, aluminum alloy, brass, mild steel, carbon steel and stainless steel. The liquid droplets considered are 30 ± 5 μm in volume average diameter of water, which is the same order of droplet diameter in the actual pipeline in nuclear/fossil power plants. In order to understand the influence of material hardness on the liquid droplet impingement erosion, the scanning electron microscope (SEM) observation on the eroded surface and the measurement of erosion rate are carried out in the terminal stage of erosion. The experimental results indicate that the erosion rates are expressed by the droplet velocity, volume flux, Vickers hardness and the liquid film thickness, which are fundamentals of the liquid droplet impingement erosion. The empirical formula shows that the power index for droplet velocity dependency is found to be 7 with a scattering from 5 to 9 depending on the materials, while the power index for Vickers hardness dependency is found as −4.5

The influence of material hardness on liquid droplet impingement erosion

Energy Technology Data Exchange (ETDEWEB)

Fujisawa, Nobuyuki, E-mail: fujisawa@eng.niigata-u.ac.jp [Visualization Research Center, Niigata University, 8050, Ikarashi 2-Nocho, Nishi-ku, Niigata 950-2181 (Japan); Yamagata, Takayuki, E-mail: yamagata@eng.niigata-u.ac.jp [Visualization Research Center, Niigata University, 8050, Ikarashi 2-Nocho, Nishi-ku, Niigata 950-2181 (Japan); Takano, Shotaro; Saito, Kengo [Graduate School of Science and Technology, Niigata University, 8050, Ikarashi 2-Nocho, Nishi-ku, Niigata 950-2181 (Japan); Morita, Ryo; Fujiwara, Kazutoshi; Inada, Fumio [Central Research Institute of Electric Power Industry, 2-11-1, Iwatokita, Komae, Tokyo 201-8511 (Japan)

2015-07-15

Highlights: • Liquid droplet impingement erosion is studied for various metal materials. • Average power dependency on droplet velocity is found as 7. • Power dependency on Vickers hardness is found as −4.5. • An empirical formula is constructed for erosion rates of metal materials. • Predicted erosion rate is well correlated with experiment within a factor of 1.5. - Abstract: This paper describes the experimental study on the liquid droplet impingement erosion of metal materials to understand the influence of material hardness on the erosion rate. The experiment is carried out using a water spray jet apparatus with a condition of relatively thin liquid film thickness. The metal materials tested are pure aluminum, aluminum alloy, brass, mild steel, carbon steel and stainless steel. The liquid droplets considered are 30 ± 5 μm in volume average diameter of water, which is the same order of droplet diameter in the actual pipeline in nuclear/fossil power plants. In order to understand the influence of material hardness on the liquid droplet impingement erosion, the scanning electron microscope (SEM) observation on the eroded surface and the measurement of erosion rate are carried out in the terminal stage of erosion. The experimental results indicate that the erosion rates are expressed by the droplet velocity, volume flux, Vickers hardness and the liquid film thickness, which are fundamentals of the liquid droplet impingement erosion. The empirical formula shows that the power index for droplet velocity dependency is found to be 7 with a scattering from 5 to 9 depending on the materials, while the power index for Vickers hardness dependency is found as −4.5.

Cavitation erosion - corrosion behaviour of ASTM A27 runner steel in natural river water

International Nuclear Information System (INIS)

Tôn-Thât, L

2014-01-01

Cavitation erosion is still one of the most important degradation modes in hydraulic turbine runners. Part of researches in this field focuses on finding new materials, coatings and surface treatments to improve the resistance properties of runners to this phenomenon. However, only few studies are focused on the deleterious effect of the environment. Actually, in some cases a synergistic effect between cavitation erosion mechanisms and corrosion kinetics can establish and increase erosion rate. In the present study, the cavitation erosion-corrosion behaviour of ASTM A27 steel in natural river water is investigated. This paper state the approach which has been used to enlighten the synergy between both phenomena. For this, a 20 kHz vibratory test according ASTM G32 standard is coupled to an electrochemical cell to be able to follow the different corrosion parameters during the tests to get evidence of the damaging mechanism. Moreover, mass losses have been followed during the exposure time. The classical degradation parameters (cumulative weight loss and erosion rate) are determined. Furthermore, a particular effort has been implemented to determine the evolution of surface damages in terms of pitting, surface cracking, material removal and surface corrosion. For this, scanning electron microscopy has been used to link the microstructure to the material removal mechanisms

Extent of Cropland and Related Soil Erosion Risk in Rwanda

Directory of Open Access Journals (Sweden)

Fidele Karamage

2016-06-01

Full Text Available Land conversion to cropland is one of the major causes of severe soil erosion in Africa. This study assesses the current cropland extent and the related soil erosion risk in Rwanda, a country that experienced the most rapid population growth and cropland expansion in Africa over the last decade. The land cover land use (LCLU map of Rwanda in 2015 was developed using Landsat-8 imagery. Based on the obtained LCLU map and the spatial datasets of precipitation, soil properties and elevation, the soil erosion rate of Rwanda was assessed at 30-m spatial resolution, using the Revised Universal Soil Loss Equation (RUSLE model. According to the results, the mean soil erosion rate was 250 t·ha−1·a−1 over the entire country, with a total soil loss rate of approximately 595 million tons per year. The mean soil erosion rate over cropland, which occupied 56% of the national land area, was estimated at 421 t·ha−1·a−1 and was responsible for about 95% of the national soil loss. About 24% of the croplands in Rwanda had a soil erosion rate larger than 300 t·ha−1·a−1, indicating their unsuitability for cultivation. With a mean soil erosion rate of 1642 t·ha−1·a−1, these unsuitable croplands were responsible for 90% of the national soil loss. Most of the unsuitable croplands are distributed in the Congo Nile Ridge, Volcanic Range mountain areas in the west and the Buberuka highlands in the north, regions characterized by steep slopes (>30% and strong rainfall. Soil conservation practices, such as the terracing cultivation method, are paramount to preserve the soil. According to our assessment, terracing alone could reduce the mean cropland soil erosion rate and the national soil loss by 79% and 75%, respectively. After terracing, only a small proportion of 7.6% of the current croplands would still be exposed to extreme soil erosion with a rate >300 t·ha−1·a−1. These irremediable cropland areas should be returned to mountain forest to

The positive impact of European subsidies on soil erosion rates in orange plantations

Science.gov (United States)

Keesstra, Saskia; Jordán, Antonio; Novara, Agata; Taguas, Tani; Pereira, Paulo; Brevik, Eric C.; Cerdà, Artemi

2017-04-01

Soil erosion in orchards and vineyards has been found non-sustainable due to bare soils due to the use of herbicides and tillage (Novara et al., 2011; Taguas et al., 2015; Ochoa et al., 2016; Rodrigo Comino et al., 2016a; 2016b; 2016c). Citrus plantations in sloping terrains are also non-sustainable from the soil erosion point of view due high erosion rates and the damage caused on infra-structures (Cerdà et al., 2009; 2009b; Cerdà et al., 2011; Pereira et al., 2015). This is not uncommon in Mediterranean type Ecosystems (Cerdà et al., 2010) but there is a need to reduce the soil and water losses to achieve sustainability (Brevik et al., 2015; Keesstra et al., 2016). The use of mulches, geotextiles, catch crops, and vegetation was found to be very successful as a sustainable strategy to reduce the soil losses (Giménez Morera et al., 2010; Mwango et al., 2016; Nawaz et al., 2016; Nishigaki et al., 2016; Prosdocimi et al., 2016). Nowadays, chipped branches are applied in orchards and vineyards because of European subsidies; however little scientific data is available on the impact of the chipped branches mulch on soil erosion. In an orange plantation in Eastern Valencia, at the L'Alcoleja experimental station the impact of these chipped branches was tested under 45 mm h-1 rainfall simulations on laboratory plots of 0.5 m2 under with different covers of chipped branches. The results show that with a cover of 20 % with chipped branches soil erosion reduces by 78 %. Acknowledgements The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007-2013) under grant agreement 603498 (RECARE project) and the CGL2013- 47862-C2-1-R and CGL2016-75178-C2-2-R national research projects. References Brevik, E. C., Cerdà, A., Mataix-Solera, J., Pereg, L., Quinton, J. N., Six, J., and Van Oost, K. 2015. The interdisciplinary nature of SOIL, SOIL, 1, 117-129, doi:10.5194/soil-1-117-2015, Cerdà, A. and M. F. Jurgensen

A linear relationship between wave power and erosion determines salt-marsh resilience to violent storms and hurricanes

Science.gov (United States)

Leonardi, Nicoletta; Ganju, Neil K.; Fagherazzi, Sergio

2016-01-01

Salt marsh losses have been documented worldwide because of land use change, wave erosion, and sea-level rise. It is still unclear how resistant salt marshes are to extreme storms and whether they can survive multiple events without collapsing. Based on a large dataset of salt marsh lateral erosion rates collected around the world, here, we determine the general response of salt marsh boundaries to wave action under normal and extreme weather conditions. As wave energy increases, salt marsh response to wind waves remains linear, and there is not a critical threshold in wave energy above which salt marsh erosion drastically accelerates. We apply our general formulation for salt marsh erosion to historical wave climates at eight salt marsh locations affected by hurricanes in the United States. Based on the analysis of two decades of data, we find that violent storms and hurricanes contribute less than 1% to long-term salt marsh erosion rates. In contrast, moderate storms with a return period of 2.5 mo are those causing the most salt marsh deterioration. Therefore, salt marshes seem more susceptible to variations in mean wave energy rather than changes in the extremes. The intrinsic resistance of salt marshes to violent storms and their predictable erosion rates during moderate events should be taken into account by coastal managers in restoration projects and risk management plans.

A linear relationship between wave power and erosion determines salt-marsh resilience to violent storms and hurricanes.

Science.gov (United States)

Leonardi, Nicoletta; Ganju, Neil K; Fagherazzi, Sergio

2016-01-05

Salt marsh losses have been documented worldwide because of land use change, wave erosion, and sea-level rise. It is still unclear how resistant salt marshes are to extreme storms and whether they can survive multiple events without collapsing. Based on a large dataset of salt marsh lateral erosion rates collected around the world, here, we determine the general response of salt marsh boundaries to wave action under normal and extreme weather conditions. As wave energy increases, salt marsh response to wind waves remains linear, and there is not a critical threshold in wave energy above which salt marsh erosion drastically accelerates. We apply our general formulation for salt marsh erosion to historical wave climates at eight salt marsh locations affected by hurricanes in the United States. Based on the analysis of two decades of data, we find that violent storms and hurricanes contribute less than 1% to long-term salt marsh erosion rates. In contrast, moderate storms with a return period of 2.5 mo are those causing the most salt marsh deterioration. Therefore, salt marshes seem more susceptible to variations in mean wave energy rather than changes in the extremes. The intrinsic resistance of salt marshes to violent storms and their predictable erosion rates during moderate events should be taken into account by coastal managers in restoration projects and risk management plans.

Combined impacts of land use and soil property changes on soil erosion in a mollisol area under long-term agricultural development.

Science.gov (United States)

Ouyang, Wei; Wu, Yuyang; Hao, Zengchao; Zhang, Qi; Bu, Qingwei; Gao, Xiang

2018-02-01

Soil erosion exhibits special characteristics in the process of agricultural development. Understanding the combined impacts of land use and soil property changes on soil erosion, especially in the area under long-term agricultural cultivations, is vital to watershed agricultural and soil management. This study investigated the temporal-spatial patterns of the soil erosion based on a modified version of Universal Soil Loss Equation (USLE) and conducted a soil erosion contribution analysis. The land use data were interpreted from Landsat series images, and soil properties were obtained from field sampling, laboratory tests and SPAW (Soil-Plant-Atmosphere-Water) model calculations. Over a long period of agricultural development, the average erosion modulus decreased from 187.7tkm -2 a -1 in 1979 to 158.4tkm -2 a -1 in 2014. The land use types were transformed mainly in the reclamation of paddy fields and the shrinking of wetlands on a large scale. Most of the soils were converted to loam from silty or clay loam and the saturated hydraulic conductivity (K s ) of most soil types decreased by 1.11% to 43.6%. The rapidly increasing area of 49.8km 2 of paddy fields together with the moderate decrease of 14.0km 2 of forests, as well as K s values explained 87.4% of the total variance in soil erosion. Although changes in soil physical and water characteristics indicated that soil erosion loads should have become higher, the upsurge in paddy fields played an important role in mitigating soil erosion in this study area. These results demonstrated that land use changes had more significant impacts than soil property changes on soil erosion. This study suggested that rational measures should be taken to extend paddy fields and control the dry land farming. These findings will benefit watershed agricultural targeting and management. Copyright © 2017 Elsevier B.V. All rights reserved.

Solid particle erosion of polymers and composites

Science.gov (United States)

Friedrich, K.; Almajid, A. A.

2014-05-01

After a general introduction to the subject of solid particle erosion of polymers and composites, the presentation focusses more specifically on the behavior of unidirectional carbon fiber (CF) reinforced polyetheretherketone (PEEK) composites under such loadings, using different impact conditions and erodents. The data were analyzed on the basis of a newly defined specific erosive wear rate, allowing a better comparison of erosion data achieved under various testing conditions. Characteristic wear mechanisms of the CF/PEEK composites consisted of fiber fracture, matrix cutting and plastic matrix deformation, the relative contribution of which depended on the impingement angles and the CF orientation. The highest wear rates were measured for impingement angles between 45 and 60°. Using abrasion resistant neat polymer films (in this case PEEK or thermoplastic polyurethane (TPU) ones) on the surface of a harder substrate (e.g. a CF/PEEK composite plate) resulted in much lower specific erosive wear rates. The use of such polymeric films can be considered as a possible method to protect composite surfaces from damage caused by minor impacts and erosion. In fact, they are nowadays already successfully applied as protections for wind energy rotor blades.

Using cosmogenic isotopes to measure basin-scale rates of erosion

International Nuclear Information System (INIS)

Bierman, P.R.; Steig, E.

1992-01-01

The authors present a new and different approach to interpreting the abundance of in situ-produced cosmogenic nuclides such as 36 Cl, 26 Al, and 10 Be. Unlike most existing models, which are appropriate for evaluating isotope concentrations on bedrock surfaces, this model can be used to interpret isotope concentration in fluvial sediment. Because sediment is a mixture of material derived from the entire drainage basin, measured isotope abundances can be used to estimate spatially-averaged rates of erosion and sediment transport. Their approach has the potential to provide geomorphologists with a relatively simple but powerful means by which to constrain rates of landscape evolution. The model considers the flux of cosmogenic isotopes into and out of various reservoirs. Implicit in model development are the assumptions that a geomorphic steady-state has been reached and that sampled sediment is spatially and temporally representative of all sediment leaving the basin. Each year, the impinging cosmic-ray flux produces a certain quantity of cosmogenic isotopes in the rock and soil of a drainage basin. For a basin in steady state, the outgoing isotope flux is also constant. They solve for the rate of mass loss as a function of isotope abundance in the sediment, the cosmic ray attenuation length, the isotope half life, and the effective isotope production rate. There are only a few published measurements of cosmogenic isotope abundance in sediment. They calculated model denudation rates for sediment samples from Zaire and central Texas. The denudation rates they calculated appear reasonable and are similar to those they have measured directly on granite landforms in Georgia and southeastern California and those calculated for the Appalachian Piedmont

Erosion products in disruption simulation experiments

International Nuclear Information System (INIS)

Safronov, V.; Arkhipov, N.; Bakhtin, V.; Barsuk, V.; Kurkin, S.; Mironova, E.; Toporkov, D.; Vasenin, S.; Zhitlukhin, A.; Arkhipov, I.; Werle, H.; Wuerz, H.

1998-01-01

Erosion of divertor materials under tokamak disruption event presents a serious problem of ITER technology. Erosion restricts the divertor lifetime and leads to production of redeposited layers of the material retaining large amount of tritium, which is a major safety issue for future fusion reactor. Since ITER disruptive heat loads are not achievable in existing tokamaks, material erosion is studied in special simulation experiments. Till now the simulation experiments have focused mainly on investigation of shielding effect and measurement of erosion rate. In the present work the properties of eroded and redeposited graphite are studied under condition typical for hard ITER disruption. (author)

The history and assessment of effectiveness of soil erosion control measures deployed in Russia

Directory of Open Access Journals (Sweden)

Valentin Golosov

2013-09-01

Full Text Available Research activities aimed at design and application of soil conservation measures for reduction of soil losses from cultivated fields started in Russia in the last quarter of the 19th century. A network of "zonal agrofor-estry melioration experimental stations" was organized in the different landscape zones of Russia in the first half of the 20th century. The main task of the experiments was to develop effective soil conservation measures for Russian climatic,soil and land use conditions. The most widespread and large-scale introduction of coun-termeasures to cope with soil erosion by water and wind into agricultural practice supported by serious governmental investments took place during the Soviet Union period after the Second World War. After the Soviet Union collapse in 1991 ,general deterioration of the agricultural economy sector and the absence of investments resulted in cessation of organized soil conservation measures application at the nation-wide level. However, some of the long-term erosion control measures such as forest shelter belts, artificial slope terracing, water diversion dams above formerly active gully heads survived until the present. In the case study of sediment redistribution within the small cultivated catchment presented in this paper an attempt was made to evaluate average annual erosion rates on arable slopes with and without soil conservation measures for two time intervals. It has been found that application of conservation measures on cultivated slopes within the experimental part of the case study catchment has led to a decrease of average soil loss rates by at least 2. 5 2. 8 times. The figures obtained are in good agreement with previously published results of direct monitoring of snowmelt erosion rates, reporting approximately a 3 -fold decrease of average snowmelt erosion rates in the experimental sub-catchment compared to a traditionally cultivated control sub-catchment. A substantial decrease of soil

Bedrock river erosion measurements and modelling along a river of the Frontal Himalaya

Science.gov (United States)

Lave, Jerome; Dubille, Matthieu

2017-04-01

River incision is a key process in mountains denudation and therefore in landscape evolution models. Despite its importance, most incision models for mountain rivers rely on simplified, or quite empirical relations, and generally only consider annual average values for water discharge and sediment flux. In contrast, very few studies consider mechanistic models at the timescale of a flood, and try to bridge the gap between experimental or theoretical approaches and long term river incision studies. In this contribution, we present observations made during 7 monsoon seasons on fluvial bedrock erosion along the Bakeya river across the Frontal Himalaya in Central Nepal. Along its lower gorge, this river incises alternation of indurated sandstone and less resistant claystone, at Holocene rates larger than 10mm/yr. More importantly, its upper drainage mostly drains through non-cohesive conglomerate which allows, in this specific setting, estimating the bedload characteristics and instantaneous fluxes, i.e. a pre-requisite to test mechanistic models of fluvial erosion. During the study period, we monitored and documented the channel bank erosion in order to understand the amplitude of the erosion processes, their occurrence in relation with hydrology, in order to test time-integrated models of erosion. Besides hydrologic monitoring, erosion measurements were threefold: (1) at the scale of the whole monsoon, plucking and block removal by repeated photo surveys of a 400m long channel reach, (2) detailed microtopographic surveys of channel bedrock elevation along a few sandstone bars to document their abrasion, (3) real time measurement of fluvial bedrock wear to document erosion timing using a new erosion sensor. Results indicate that: 1. Erosion is highly dependent on rock resistance, but on average block detachment and removal is a more efficient process than bedrock attrition, and operates at a rate that permit channel banks downcutting to keep pace with Holocene uplift

Erosion of the first wall of Tokamaks

International Nuclear Information System (INIS)

Guseva, M.I.; Ionova, E.S.; Martynenko, Yu.V.

1980-01-01

An estimate of the rate of erosion of the wall due to sputtering and blistering requires knowledge of the fluxes and energies of the particles which go from the plasma to the wall, of the sputtering coefficients S, and of the erosion coefficients S* for blistering. The overall erosion coefficient is equal to the sum of the sputtering coefficient and the erosion coefficient for blistering. Here the T-20 Tokamak is examined as an example of a large-scale Tokamak. 18 refs

Growth and erosion of mountain ranges at the northeastern margin of Tibet

Science.gov (United States)

Hetzel, Ralf; Palumbo, Luigi; Giese, Jörg; Guo, Jianming

2010-05-01

fault scaling law for the growth of topography: Mountain ranges in the broken foreland of NE Tibet. Terra Nova 16, 157-162. [2] Hetzel et al. (2002). Low slip rates and long-term preservation of geomorphic features in Central Asia. Nature 417, 428-432. [3] Hetzel et al. (2004). Late Pleistocene/Holocene slip rate of the Zhangye thrust (Qilian Shan, China) and implications for the active growth of the northeastern Tibetan Plateau, Tectonics 23, TC6006, doi:10.1029/2004TC001653. [4] Goethals et al. (2009). Determining the impact of faulting on the rate of erosion in a low-relief landscape: A case study using in situ produced 21Ne on active normal faults in the Bishop Tuff, California. Geomorphology 103, 401-413. [5] Palumbo et al. (2009). Deciphering the rate of mountain growth during topographic presteady state: an example from the NE margin of the Tibetan Plateau. Tectonics 28, TC4017, doi:10.1029/2009TC002455. [6] Palumbo et al. (in press). Topographic and lithologic control on catchment-wide denudation rates derived from cosmogenic 10Be in two mountain ranges at the margin of NE Tibet. Geomorphology, doi:10.1016/j.geomorph.2009.11.019. [7] Meyer et al. (in press). Determining the growth rate of topographic relief using in situ-produced 10Be: A case study in the Black Forest, Germany. Earth and Planetary Science Letters. [8] Densmore et al. (2009). Spatial variations in catchment-averaged denudation rates from normal fault footwalls. Geology 37, 1139-1142.

Endurance test of a 30-CM-diameter engineering model ion thruster. Task 12: Investigation of thin-film erosion monitors for ion thrusters

Science.gov (United States)

Beattie, J. R.

1983-01-01

An investigation of short term measurement techniques for predicting the wearout of ion thrusters resulting from sputter erosion damage is described. The previously established laminar thin film techniques to provide high precision erosion rate data. However, the erosion rates obtained using this technique are generally substantially higher than those obtained during long term endurance tests (by virtue of the as deposited nature of the thin films), so that the results must be interpreted in a relative sense. Absolute measurements can be performed using a new masked substrate arrangement which was developed during this study. This new technique provides a means for estimating the lifetimes of critical discharge chamber components based on direct measurements of sputter erosion depths obtained during short duration (10 hour) tests. The method enables the effects on lifetime of thruster design and operating parameters to be inferred without the investment of the time and capital required to conduct long term (1000 hour) endurance tests. Results obtained using the direct measurement technique are shown to agree with sputter erosion depths calculated for the plasma conditions of the test and also with lifetest results. The direct measurement approach is shown to be applicable to both mercury and argon discharge plasma environments and should be useful in estimating the lifetimes of inert gas and extended performance mercury ion thrusters presently under development.

Decadal-scale variation in dune erosion and accretion rates: An investigation of the significance of changing storm tide frequency and magnitude on the Sefton coast, UK

Science.gov (United States)

Pye, K.; Blott, S. J.

2008-12-01

Monitoring of frontal dune erosion and accretion on the Sefton coast in northwest England over the past 50 years has revealed significant spatial and temporal variations. Previous work has shown that the spatial variations primarily reflect longshore differences in beach and nearshore morphology, energy regime and sediment budget, but the causes of temporal variations have not previously been studied in detail. This paper presents the results of work carried out to test the hypothesis that a major cause of temporal variation is changes in the frequency and magnitude of storms, surges and resulting high tides. Dune toe erosion/accretion records dating from 1958 have been compared with tide gauge records at Liverpool and Heysham. Relatively high dune erosion rates at Formby Point 1958-1968 were associated with a relatively large number of storm tides. Slower erosion at Formby, and relatively rapid accretion in areas to the north and south, occurred during the 1970's and 1980's when there were relatively few major storm tides. After 1990 rates of dune erosion at Formby increased again, and dunes to the north and south experienced slower accretion. During this period high storm tides have been more frequent, and the annual number of hours with water levels above the critical level for dune erosion has increased significantly. An increase in the rate of mean sea-level rise at both Liverpool and Heysham is evident since 1990, but we conclude that this factor is of less importance than the occurrence of extreme high tides and wave action associated with storms. The incidence of extreme high tides shows an identifiable relationship with the lunar nodal tidal cycle, but the evidence indicates that meteorological forcing has also had a significant effect. Storms and surges in the eastern Irish Sea are associated with Atlantic depressions whose direction and rate of movement have a strong influence on wind speeds, wave energy and the height of surge tides. However

Soil erosion dynamics response to landscape pattern

NARCIS (Netherlands)

Ouyang, W.; Skidmore, A.K.; Hao, F.; Wang, T.

2010-01-01

Simulating soil erosion variation with a temporal land use database reveals long-term fluctuations in landscape patterns, as well as priority needs for soil erosion conservation. The application of a multi-year land use database in support of a Soil Water Assessment Tool (SWAT) led to an accurate

Evaluating the Impacts of Climate Change on Soil Erosion Rates in Central Mexico

Directory of Open Access Journals (Sweden)

Santos Martínez-Santiago

2017-07-01

Full Text Available Although water-eroded soil (WES resulting from human activities has been recognized as the leading global cause of land degradation, the soil erosion risks from climate change are not clear. Studies have reported that WES is the second most significant cause of soil loss in Mexico, and its future trajectory has not been sufficiently evaluated. The aims of this study are to 1 determine the impacts of climate change on WES and its distribution for the State of Aguascalientes, Mexico, and to 2 compare the present and future soil loss rates for the study unit (SU. The State of Aguascalientes is located in the “Region del Bajio.” The impact of climate change on WES was evaluated using the near-future divided world scenario (A2 presented in the IPCC Fourth Assessment Report. Daily temperature and precipitation data from 18 weather stations were downscaled to model historic laminar water erosion (HLWE and changes therein in the A2 near-future scenario for 2010–2039 (LWEScA2. Due to future changes in mean annual rainfall (MAR levels, a change in the LWEScA2 of between 1.6 and 8.9% could result in average soil losses up to 475.4 t ha-1 yr-1, representing a loss of slightly more than a 30-mm layer of mountain soil per year. The risk zones, classified as class 4 for LWE, are located to western of the State in part of municipalities of Calvillo, Jesus María, San José de Gracia y Cosio, where there are typical hills and falls with soil very sensitive to rain erosion.

Erosive Lichen Planus.

Science.gov (United States)

Mauskar, Melissa

2017-09-01

Lichen planus is an inflammatory mucocutaneous condition with a myriad of clinical manifestations. There are 3 forms of lichen planus that effect the vulva: papulosquamous, hypertrophic, and erosive. Erosive lichen planus can progress to vulvar scaring, vaginal stenosis, and squamous cell carcinoma; these long-term sequelae cause sexual distress, depression, and decreased quality of life for patients. Diagnosis is often delayed because of patient embarrassment or clinician misdiagnosis. Early recognition and treatment is essential to decreasing the morbidity of this condition. Multimodal treatment, along with a multidisciplinary approach, will improve outcomes and further clinical advances in studying this condition. Copyright © 2017 Elsevier Inc. All rights reserved.

Runoff erosion

OpenAIRE

Evelpidou, Niki (Ed.); Cordier, Stephane (Ed.); Merino, Agustin (Ed.); Figueiredo, Tomás de (Ed.); Centeri, Csaba (Ed.)

2013-01-01

Table of Contents PART I – THEORY OF RUNOFF EROSION CHAPTER 1 - RUNOFF EROSION – THE MECHANISMS CHAPTER 2 - LARGE SCALE APPROACHES OF RUNOFF EROSION CHAPTER 3 - MEASURING PRESENT RUNOFF EROSION CHAPTER 4 - MODELLING RUNOFF EROSION CHAPTER 5 - RUNOFF EROSION AND HUMAN SOCIETIES: THE INFLUENCE OF LAND USE AND MANAGEMENT PRACTICES ON SOIL EROSION PART II - CASE STUDIES CASE STUDIES – INTRODUCTION: RUNOFF EROSION IN MEDITERRANEAN AREA CASE STUDY 1: Soil Erosion Risk...

Plot-slope soil erosion using 7Be measurement and rill fractal dimension

International Nuclear Information System (INIS)

Zhang Fengbao; Yang Mingyi

2010-01-01

In this study, we intended to use 7 Be measurement and fractal theory to quantify soil erosion process on slope. The results showed that contribution rate of inter rill erosion was more than that of rill erosion during early stage of rainfall. When it rained, contribution rate of rill erosion began to be higher than inter rill erosion and become the main part of erosion during medium stage of rainfall. The trend of contribution rate of inter rill erosion was growing and the rill erosion was lowering during late stage of rainfall. Rill fractal dimension on the plot slope was almost growing larger during rainfall,growing quickly during early stage of rainfall and slowly during the late stage. Correlations was positive between rill fractal dimension and total erosion amount, also positive between rill fractal dimension and rill erosion. The correlations was positive between rill fractal dimension variation and total erosion amount, also was positive between rill fractal dimension variation and rill erosion amount. The best correlation was observed between rill fractal dimension and rill erosion amount. These results indicated that the rill fractal dimension on the plot slope could represent the development process of rill,the complex degree of rill and the variation of soil erosion intensity on the entire slope. (authors)

Catchment-wide weathering and erosion rates of mafic, ultramafic, and granitic rock from cosmogenic meteoric 10Be/9Be ratios

Science.gov (United States)

Dannhaus, N.; Wittmann, H.; Krám, P.; Christl, M.; von Blanckenburg, F.

2018-02-01

Quantifying rates of weathering and erosion of mafic rocks is essential for estimating changes to the oceans alkalinity budget that plays a significant role in regulating atmospheric CO2 levels. In this study, we present catchment-wide rates of weathering, erosion, and denudation measured with cosmogenic nuclides in mafic and ultramafic rock. We use the ratio of the meteoric cosmogenic nuclide 10Be, deposited from the atmosphere onto the weathering zone, to stable 9Be, a trace metal released by silicate weathering. We tested this approach in stream sediment and water from three upland forested catchments in the north-west Czech Republic. The catchments are underlain by felsic (granite), mafic (amphibolite) and ultramafic (serpentinite) lithologies. Due to acid rain deposition in the 20th century, the waters in the granite catchment exhibit acidic pH, whereas waters in the mafic catchments exhibit neutral to alkaline pH values due to their acid buffering capability. The atmospheric depositional 10Be flux is estimated to be balanced with the streams' dissolved and particulate meteoric 10Be export flux to within a factor of two. We suggest a correlation method to derive bedrock Be concentrations, required as an input parameter, which are highly heterogeneous in these small catchments. Derived Earth surface metrics comprise (1) Denudation rates calculated from the 10Be/9Be ratio of the "reactive" Be (meaning sorbed to mineral surfaces) range between 110 and 185 t km-2 y-1 (40 and 70 mm ky-1). These rates are similar to denudation rates we obtained from in situ-cosmogenic 10Be in quartz minerals present in the bedrock or in quartz veins in the felsic and the mafic catchment. (2) The degree of weathering, calculated from the fraction of 9Be released from primary minerals as a new proxy, is about 40-50% in the mafic catchments, and 10% in the granitic catchment. Lastly, (3) erosion rates were calculated from 10Be concentrations in river sediment and corrected for sorting

Assessment of soil erosion sensitivity and post-timber-harvesting erosion response in a mountain environment of Central Italy

Science.gov (United States)

Borrelli, Pasquale; Schütt, Brigitta

2014-01-01

This study aimed to assess the effects of forest management on the occurrence of accelerated soil erosion by water. The study site is located in a mountainous area of the Italian Central Apennines. Here, forest harvesting is a widespread forestry activity and is mainly performed on the moderate to steep slopes of the highlands. Through modeling operations based on data on soil properties and direct monitoring of changes in the post-forest-harvesting soil surface level at the hillslope scale, we show that the observed site became prone to soil erosion after human intervention. Indeed, the measured mean soil erosion rate of 49 t ha- 1 yr- 1 for the harvested watershed is about 21 times higher than the rate measured in its neighboring undisturbed forested watershed (2.3 t ha- 1 yr- 1). The erosive response is greatly aggravated by exposing the just-harvested forest, with very limited herbaceous plant cover, to the aggressive attack of the heaviest annual rainfall without adopting any conservation practices. The erosivity of the storms during the first four months of field measurements was 1571 MJ mm h- 1 ha- 1 in total (i.e., from September to December 2008). At the end of the experiment (16 months), 18.8%, 26.1% and 55.1% of the erosion monitoring sites in the harvested watershed recorded variations equal or greater than 0-5, 5-10 and > 10 mm, respectively. This study also provides a quantification of Italian forestland surfaces with the same pedo-lithological characteristics exploited for wood supply. Within a period of ten years (2002-2011), about 9891 ha of coppice forest changes were identified and their potential soil erosion rates modeled.

The erosive potential of candy sprays

NARCIS (Netherlands)

Gambon, D.L.; Brand, H.S.; Nieuw Amerongen, A.V.

2009-01-01

Objective To determine the erosive potential of seven different commercially available candy sprays in vitro and in vivo. Material and methods The erosive potential was determined in vitro by measuring the pH and neutralisable acidity. The salivary pH and flow rate were measured in healthy

Erosion of Earthen Levees by Wave Action

Science.gov (United States)

Ozeren, Y.; Wren, D. G.; Reba, M. L.

2016-02-01

Earthen levees of aquaculture and irrigation reservoirs in the United States often experience significant erosion due to wind-generated waves. Typically constructed using local soils, unprotected levees are subjected to rapid erosion and retreat due to wind generated waves and surface runoff. Only a limited amount of published work addresses the erosion rates for unprotected levees, and producers who rely on irrigation reservoirs need an economic basis for selecting a protection method for vulnerable levees. This, in turn, means that a relationship between wave energy and erosion of cohesive soils is needed. In this study, laboratory experiments were carried out in order to quantify wave induced levee erosion and retreat. A model erodible bank was packed using a soil consisting of approximately 14% sand, 73% silt, and 13% clay in a 20.6 m long 0.7 m wide and 1.2 m deep wave tank at the USDA-ARS, National Sedimentation Laboratory in Oxford MS. The geometry of the levee face was monitored by digital camera and the waves were measured by means of 6 capacitance wave staffs. Relationships were established between levee erosion, edge and retreat rates, and incident wave energy.

Erosion and its rate on an accumulative Polish dune coast: the effects of the January 2012 storm surge

Directory of Open Access Journals (Sweden)

Tomasz A. Łabuz

2014-01-01

Full Text Available The Polish coast is a non-tidal area; its shores are affected mainly by autumn-winter storm surges. Those of 6 and 14 January 2012 are representative of the forces driving the erosion of normally accumulative sections of coastal dunes, monitored by the author since 1997. The sea level maximum during these two storm surges reached 1.2 to 1.5 m amsl along the Polish coast. Land forms up to 3 m amsl were inundated. Beaches and low parts of the coast up to this height were rebuilt by sea waves attacking the coast for almost 12 days. Quantitative analyses of the morphological dynamics of the coastal dunes are presented for 57 profiles located along the coast. Only those accumulative sections of the Polish coast are analysed where sand accumulation did occur and led to new foredune development. The mean rate of dune erosion was 2.5 m3 per square metre with an average toe retreat of 1.4 m. Erosion understood as dune retreat was greater when a beach was lower (correlation coefficient 0.8. Dune erosion did not occur on coasts with beaches higher than 3.2 m or on lower ones covered by embryo dunes.

The control of divertor carbon erosion/redeposition in the DIII-D tokamak

International Nuclear Information System (INIS)

Whyte, D.G.; West, W.P.; Wong, C.P.C.

2001-01-01

The DIII-D tokamak has demonstrated an operational scenario where the graphite-covered divertor is free of net erosion. Reduction of divertor carbon erosion is accomplished using a low temperature (detached) divertor plasma that eliminates physical sputtering. Likewise, the carbon source rate arising from chemical erosion is found to be very low in the detached divertor. Near strikepoint regions, the rate of carbon deposition is ∼3 cm/burn-year, with a corresponding hydrogenic codeposition rate >1kg/m 2 /burn-year; rates both problematic for steady-state fusion reactors. The carbon net deposition rate in the divertor is consistent with carbon arriving from the core plasma region. Carbon influx from the main wall is measured to be relatively large in the high-density detached regime and is of sufficient magnitude to account for the deposition rate in the divertor. Divertor redeposition is therefore determined by non-divertor erosion and transport. Despite the success in reducing divertor erosion on DIII-D with detachment, no significant reduction is found in the core plasma carbon density, illustrating the importance of non-divertor erosion and the complex coupling between erosion/redeposition and impurity plasma transport. (author)

Parameters Affecting the Erosive Burning of Solid Rocket Motor

Directory of Open Access Journals (Sweden)

Abdelaziz Almostafa

2018-01-01

Full Text Available Increasing the velocity of gases inside solid rocket motors with low port-to-throat area ratios, leading to increased occurrence and severity of burning rate augmentation due to flow of propellant products across burning propellant surfaces (erosive burning, erosive burning of high energy composite propellant was investigated to supply rocket motor design criteria and to supplement knowledge of combustion phenomena, pressure, burning rate and high velocity of gases all of these are parameters affect on erosive burning. Investigate the phenomena of the erosive burning by using the 2’inch rocket motor and modified one. Different tests applied to fulfil all the parameters that calculated out from the experiments and by studying the pressure time curve and erosive burning phenomena.

Evaluation of Spatial-Temporal Variation of Soil Detachment Rate Potential in Rill Erosion, Case study: Doshmanziari Rainfed Lands, Fars province

Directory of Open Access Journals (Sweden)

H. Karimi

2017-01-01

Full Text Available Introduction: Soil erosion by water is one of the most widespread forms of land degradation and it has caused many undesirable consequences in last decades. On steep slopes, rill erosion is the most important type of erosion, which produces sediment and rill flow. It can be also considered as a vehicle for transporting soil particles detached from upland areas. Recent studies indicate that soil detachment rates are significantly influenced by land use. It is also known that there is a major difference between detachment rates of disturbed and natural soils (Zhang et al., 2003. Plowing rills especially in steep slopes increases sediment production. Sun et al. (2013 reported that the contribution of rill erosion in hill slope lands in china was more than 70%, which was approximately 50% of total soil erosion. In addition, measured soil loss is statistically related to hydraulic indicators such as slope, water depth, flow velocity, flow shear stress and stream power (Knapen et al., 2007. This study aims to evaluate the effects of hydraulic variables (shear stress and stream power on spatial-temporal soil detachment rate. The focus is on the plowing rills in hillslope areas under wheat dry farming cultivation. Materials and Methods: The study area is located in hilly slopes with the slope of 22.56% under dry farming wheat cultivation at 60 km of west of Shiraz, Iran. Top-down conventional plowing was carried out in order to create 10 meters furrows. Slope and cross sections of rills were measured throughout the experiment at 1 m intervals by rill-meter. Water was added to the top of the rills for 10 minutes and inflow rates were 10, 15 and 20 L min-1. Hydraulic parameters such as shear stress and stream power were calculated measuring rill morphology and water depth. Flow velocity and hydraulic radius along the different rill experiments were also calculated. Sediment concentrations were measured in three equal regular time and distance intervals

Modelling rainfall erosion resulting from climate change

Science.gov (United States)

Kinnell, Peter

2016-04-01

It is well known that soil erosion leads to agricultural productivity decline and contributes to water quality decline. The current widely used models for determining soil erosion for management purposes in agriculture focus on long term (~20 years) average annual soil loss and are not well suited to determining variations that occur over short timespans and as a result of climate change. Soil loss resulting from rainfall erosion is directly dependent on the product of runoff and sediment concentration both of which are likely to be influenced by climate change. This presentation demonstrates the capacity of models like the USLE, USLE-M and WEPP to predict variations in runoff and erosion associated with rainfall events eroding bare fallow plots in the USA with a view to modelling rainfall erosion in areas subject to climate change.

Polymers Erosion and Contamination Experiment Being Developed

Science.gov (United States)

deGroh, Kim K.; Banks, Bruce A.; Barney-Barton, Elyse A.; Sechkar, Edward; Hunt, Patricia

1999-01-01

The Polymers Erosion and Contamination Experiment (PEACE) is currently being developed at the NASA Lewis Research Center by the Electro-Physics Branch in conjunction with students and faculty from Hathaway Brown School in Cleveland. The experiment is a Get Away Special Canister shuttle flight experiment sponsored by the American Chemical Society. The two goals of this experiment are (1) to measure ram atomic oxygen erosion rates of approximately 40 polymers that have potential use in space applications and (2) to validate a method for identifying sources of silicone contamination that occur in the shuttle bay. Equipment to be used in this flight experiment is shown in the schematic diagram. Spacecraft materials subjected to attack by atomic oxygen in the space environment experience significant degradation over the span of a typical mission. Therefore, learning the rates of atomic oxygen erosion of a wide variety of polymers would be of great benefit to future missions. PEACE will use two independent techniques to determine the atomic oxygen erosion rates of polymers. Large (1-in.-diameter) samples will be used for obtaining mass loss. Preflight and postflight dehydrated masses will be obtained, and the mass lost during flight will be determined. Small (0.5-in.-diameter) samples will be protected with isolated particles (such as NaCl crystals) and then exposed to the space environment. After flight, the protective particles will be removed (washed off) and atomic force microscopy (AFM) will be used to measure the erosion depth from protected mesas. Erosion depth measurements are more sensitive than traditional mass measurements and are very useful for materials with low erosion yields or with very low fluence missions.

Modelling soil carbon fate under erosion process in vineyard

Science.gov (United States)

Novara, Agata; Scalenghe, Riccardo; Minacapilli, Mario; Maltese, Antonino; Capodici, Fulvio; Borgogno Mondino, Enrico; Gristina, Luciano

2017-04-01

Soil erosion processes in vineyards beyond water runoff and sediment transport have a strong effect on soil organic carbon loss (SOC) and redistribution along the slope. The variation of SOC across the landscape determines a difference in soil fertility and vine productivity. The aim of this research was to study erosion of a Mediterranean vineyard, develop an approach to estimate the SOC loss, correlate the vines vigor with sediment and carbon erosion. The study was carried out in a Sicilian (Italy) vineyard, planted in 2011. Along the slope, six pedons were studied by digging 6 pits up to 60cm depth. Soil was sampled in each pedon every 10cm and SOC was analyzed. Soil erosion, detachment and deposition areas were measured by pole height method. The vigor of vegetation was expressed in term of NDVI (Normalized difference Vegetation Index) derived from a satellite image (RapidEye) acquired at berry pre-veraison stage (July) and characterized by 5 spectral bands in the shortwave region, including a band in the red wavelength (R, 630-685 nm) and in the near infrared (NIR, 760-850 nm) . Results showed that soil erosion, sediments redistribution and SOC across the hill was strongly affected by topographic features, slope and curvature. The erosion rate was 46Mg ha-1 y-1 during the first 6 years since planting. The SOC redistribution was strongly correlated with the detachment or deposition area as highlighted by pole height measurements. The approach developed to estimate the SOC loss showed that during the whole study period the off-farm SOC amounts to 1.6Mg C ha-1. As highlighted by NDVI results, the plant vigor is strong correlated with SOC content and therefore, developing an accurate NDVI approach could be useful to detect the vineyard areas characterized by low fertility due to erosion process.

Modeling Long-Term Fluvial Incision : Shall we Care for the Details of Short-Term Fluvial Dynamics?

Science.gov (United States)

Lague, D.; Davy, P.

2008-12-01

Fluvial incision laws used in numerical models of coupled climate, erosion and tectonics systems are mainly based on the family of stream power laws for which the rate of local erosion E is a power function of the topographic slope S and the local mean discharge Q : E = K Qm Sn. The exponents m and n are generally taken as (0.35, 0.7) or (0.5, 1), and K is chosen such that the predicted topographic elevation given the prevailing rates of precipitation and tectonics stay within realistic values. The resulting topographies are reasonably realistic, and the coupled system dynamics behaves somehow as expected : more precipitation induces increased erosion and localization of the deformation. Yet, if we now focus on smaller scale fluvial dynamics (the reach scale), recent advances have suggested that discharge variability, channel width dynamics or sediment flux effects may play a significant role in controlling incision rates. These are not factored in the simple stream power law model. In this work, we study how these short- term details propagate into long-term incision dynamics within the framework of surface/tectonics coupled numerical models. To upscale the short term dynamics to geological timescales, we use a numerical model of a trapezoidal river in which vertical and lateral incision processes are computed from fluid shear stress at a daily timescale, sediment transport and protection effects are factored in, as well as a variable discharge. We show that the stream power law model might still be a valid model but that as soon as realistic effects are included such as a threshold for sediment transport, variable discharge and dynamic width the resulting exponents m and n can be as high as 2 and 4. This high non-linearity has a profound consequence on the sensitivity of fluvial relief to incision rate. We also show that additional complexity does not systematically translates into more non-linear behaviour. For instance, considering only a dynamical width

Comparison of the soil losses from 7Be measurements and the monitoring data by erosion pins and runoff plots in the Three Gorges Reservoir region, China

International Nuclear Information System (INIS)

Shi Zhonglin; Wen Anbang; Zhang Xinbao; Yan Dongchun

2011-01-01

The potential for using 7 Be measurements to document soil redistribution associated with a heavy rainfall was estimated using 7 Be method on a bare purple soil plot in the Three Gorges Reservoir region of China. The results were compared with direct measurement from traditional approaches of erosion pins and runoff plots. The study shows that estimation of soil losses from 7 Be are comparable with the monitoring results provided by erosion pins and runoff plots, and are also in agreement with the existing knowledge provided by 137 Cs measurements. The results obtained from this study demonstrated the potential for using 7 Be technique to quantify short-term erosion rates in these areas. - Highlights: → The soil redistribution associated with a heavy rainfall was estimated using 7 Be measurements. → Estimation of soil losses from 7 Be are comparable with the monitoring data provided by erosion pins and runoff plots. → The potential for using 7 Be measurements to quantify short-term erosion rates in purple soil areas was demonstrated.

Scoping erosion flow loop test results in support of Hanford WTP

International Nuclear Information System (INIS)

Duignan, M.; Imrich, K.; Fowley, M.; Restivo, M.; Reigel, M.

2015-01-01

The Waste Treatment and Immobilization Plant (WTP) will process Hanford Site tank waste by converting the waste into a stable glass form. Before the tank waste can be vitrified, the baseline plan is to process the waste through the Pretreatment (PT) Facility where it will be mixed in various process vessels using Pulse Jet Mixers (PJM) and transferred to the High Level Waste (HLW) or Low Activity Waste (LAW) vitrification facilities. The Department of Energy (DOE) and Defense Nuclear Facility Safety Board (DNFSB), as well as independent review groups, have raised concerns regarding the design basis for piping erosion in the PT Facility. Due to the complex nature of slurry erosion/corrosion wear and the unique conditions that exist within the PT Facility, additional testing has been recommended by these entities. Pipe loop testing is necessary to analyze the potential for localized wear at elbows and bends, close the outstanding PT and HLW erosion/corrosion technical issues, and underpin BNI's design basis for a 40-year operational life for black cell piping and vessels. SRNL is consulting with the DOE Office of River Protection (ORP) to resolve technical concerns related to piping erosion/corrosion (wear) design basis for PT. SRNL was tasked by ORP to start designing, building, and testing a flow loop to obtain long-term total-wear rate data using bounding simulant chemistry, operating conditions, and prototypical materials. The initial test involved a scoping paint loop to locate experimentally the potential high-wear locations. This information will provide a basis for the placement of the many sensitive wear measurement instruments in the appropriate locations so that the principal flow-loop test has the best chance to estimate long-term erosion and corrosion. It is important to note that the scoping paint loop test only utilized a bounding erosion simulant for this test. A full chemical simulant needs to be added for the complete test flow loop. The

Predicting the Rate of River Bank Erosion Caused by Large Wood Log

Science.gov (United States)

Zhang, N.; Rutherfurd, I.; Ghisalberti, M.

2016-12-01

When a single tree falls into a river channel, flow is deflected and accelerated between the tree roots and the bank face, increasing shear stress and scouring the bank. The scallop shaped erosion increases the diversity of the channel morphology, but also causes concern for adjacent landholders. Concern about increased bank erosion is one of the main reasons for large wood to still be removed from channels in SE Australia. Further, the hydraulic effect of many logs in the channel can reduce overall bank erosion rates. Although both phenomena have been described before, this research develops a hydraulic model that estimates their magnitude, and tests and calibrates this model with flume and field measurements, with logs with various configurations and sizes. Specifically, the model estimates the change in excess shear stress on the bank associated . The model addresses the effect of the log angle, distance from bank, and log size and flow condition by solving the mass continuity and energy conservation between the cross section at the approaching flow and contracted flow. Then, we evaluate our model against flume experiment preformed with semi-realistic log models to represent logs in different sizes and decay stages by comparing the measured and simulated velocity increase in the gap between the log and the bank. The log angle, distance from bank, and flow condition are systemically varied for each log model during the experiment. Final, the calibrated model is compared with the field data collected in anabranching channels of Murray River in SE Australia where there are abundant instream logs and regulated and consistent high flow for irrigation. Preliminary results suggest that a log can significantly increase the shear stress on the bank, especially when it positions perpendicular to the flow. The shear stress increases with the log angle in a rising curve (The log angle is the angle between log trunk and flow direction. 0o means log is parallel to flow with

An investigation into the dental health of children with obesity: an analysis of dental erosion and caries status.

Science.gov (United States)

Tong, H J; Rudolf, M C J; Muyombwe, T; Duggal, M S; Balmer, R

2014-06-01

To investigate whether children with obesity experienced more erosion and caries than children with normal weight. This study involved children aged 7-15 years. The study and control group comprised 32 children with BMI > 98th centile and 32 healthy children with normal BMI-for-age, respectively. O'Sullivan Erosion Index and WHO Caries Index were used in the examination of erosion and caries, respectively. Stimulated salivary flow rate, buffering capacity, Streptococcus mutans and lactobacilli counts (CFU/ml) were evaluated. A cross-sectional questionnaire survey was employed to collect information on participant's demographic background, oral health history and habits, and utilisation of dental care services. Children with obesity were more likely to have erosion than healthy children (p erosion in terms of severity (p erosion (OR 0.32, 95 % CI 0.012-0.082). Gender had no effect on erosion. There were no statistically significant differences in the DMFT, saliva profiles or questionnaire responses between the groups. Children with obesity may have high risk of dental erosion, but do not necessarily have higher risk of dental caries than children with normal weight.

Erosion of surface and near surface disposal facilities

International Nuclear Information System (INIS)

1988-06-01

A literature search was undertaken to identify existing data and analytical procedures regarding the processes of gully erosion. The applicability of the available information to the problems of gully erosion potential at surface and near surface disposal sites is evaluated. It is concluded that the existing knowledge regarding gully erosion is insufficient to develop procedures to ensure the long-term stability of disposal sites. Recommendations for further research are presented. 46 refs

Dynamic Analysis of Soil Erosion in Songhua River Watershed

Science.gov (United States)

Zhang, Yujuan; Li, Xiuhai; Wang, Qiang; Liu, Jiang; Liang, Xin; Li, Dan; Ni, Chundi; Liu, Yan

2018-01-01

In this paper, based on RS and GIS technology and Revised Universal Soil Loss Equation (RUSLE), the soil erosion dynamic changes during the two periods of 1990 and 2010 in Bin County was analyzed by using the Landsat TM data of the two periods, so as to reveal the soil erosion spatial distribution pattern and spatial and temporal dynamic evolution rule in the region. The results showed that: the overall patterns of soil erosion were basically the same in both periods, mainly featuring slight erosion and mild erosion, with the area proportions of 80.68% and 74.71% respectively. The slight and extremely intensive erosion changing rates showed a narrowing trend; mild, moderate and intensive erosion was increasing, with a trend of increased soil erosion; mild and intensive erosion were developing towards moderate erosion and moderate and extremely intensive erosion were progressing towards intensive erosion.

Synergistic erosion/corrosion of superalloys in PFB coal combustor effluent

Science.gov (United States)

Benford, S. M.; Zellars, G. R.; Lowell, C. E.

1981-01-01

Two Ni-based superalloys were exposed to the high velocity effluent of a pressurized fluidized bed coal combustor. Targets were 15 cm diameter rotors operating at 40,000 rpm and small flat plate specimens. Above an erosion rate threshold, the targets were eroded to bare metal. The presence of accelerated oxidation at lower erosion rates suggests erosion/corrosion synergism. Various mechanisms which may contribute to the observed oxide growth enhancement include erosive removal of protective oxide layers, oxide and subsurface cracking, and chemical interaction with sulfur in the gas and deposits through damaged surface layers.

Simulation of erosion by a particulate airflow through a ventilator

Science.gov (United States)

Ghenaiet, A.

2015-08-01

Particulate flows are a serious problem in air ventilation systems, leading to erosion of rotor blades and aerodynamic performance degradation. This paper presents the numerical results of sand particle trajectories and erosion patterns in an axial ventilator and the subsequent blade deterioration. The flow field was solved separately by using the code CFX- TASCflow. The Lagrangian approach for the solid particles tracking implemented in our inhouse code considers particle and eddy interaction, particle size distribution, particle rebounds and near walls effects. The assessment of erosion wear is based on the impact frequency and local values of erosion rate. Particle trajectories and erosion simulation revealed distinctive zones of impacts with high rates of erosion mainly on the blade pressure side, whereas the suction side is eroded around the leading edge.

Tectonic control of erosion in the southern Central Andes

Science.gov (United States)

Val, Pedro; Venerdini, Agostina L.; Ouimet, William; Alvarado, Patricia; Hoke, Gregory D.

2018-01-01

Landscape evolution modeling and global compilations of exhumation data indicate that a wetter climate, mainly through orographic rainfall, can govern the spatial distribution of erosion rates and crustal strain across an orogenic wedge. However, detecting this link is not straightforward since these relationships can be modulated by tectonic forcing and/or obscured by heavy-tailed frequencies of catchment discharge. This study combines new and published along-strike average rates of catchment erosion constrained by 10Be and river-gauge data in the Central Andes between 28°S and 36°S. These data reveal a nearly identical latitudinal pattern in erosion rates on both sides of the range, reaching a maximum of 0.27 mm/a near 34°S. Collectively, data on topographic and fluvial relief, variability of rainfall and discharge, and crustal seismicity suggest that the along-strike pattern of erosion rates in the southern Central Andes is largely independent of climate, but closely relates to the N-S distribution of shallow crustal seismicity and diachronous surface uplift. The consistently high erosion rates on either side of the orogen near 34°S imply that climate plays a secondary role in the mass flux through an orogenic wedge where the perturbation to base level is similar on both sides.

Streamflow, suspended-sediment, and soil-erosion data from Kaulana and Hakioawa watersheds, Kaho'olawe, Hawai'i,

Science.gov (United States)

Izuka, Scot K.; Abbott, Lyman L.

2010-01-01

, include sites that showed overall erosion as well as sites that showed overall deposition. The average rate of change was -1 mm/yr for both the 32 sites on rills and the 42 sites on interfluves; both categories include sites that showed deposition as well as sites that showed erosion. All three sites on hummocks showed overall erosion, with an average rate of -8 mm/yr. Both the Hakioawa and Kaulana watersheds showed an average rate of change of -1 mm/yr, and both included sites that showed erosion and sites that showed deposition. For sites with negative rates of change indicating erosion, the average rate of change during the monitoring period was -2 mm/yr in restoration areas and -3 mm/yr in nonrestoration areas. For sites with positive rates of change indicating deposition, the average rate of change was 5 mm/yr in restoration areas and 6 mm/yr in nonrestoration sites. The average rate of change for rills was 1 mm/yr in restoration areas and -2 mm/yr in nonrestoration sites. The average rate of change for interfluves was below detection in restoration areas and -1 mm/yr in nonrestoration areas. Potential Use and Limitation of Data.-Additional statistical comparisons of various subsets of erosion data can be used to assess the effectiveness of restoration efforts or how existing landforms, vegetation, climate, and other physical basin characteristics affect erosion and fluvial sediment transport in the watersheds. Further investigation to identify what factors cause the Kaulana watershed to have much lower runoff and sediment loads than the Hakioawa watershed may yield valuable information for developing and modifying restoration strategies. Continued monitoring of streamflow, sediment transport, and erosion is key to assessing the long-term effectiveness of restoration and can provide insight to the island's recovery since the eradication of feral goats and cessation of use as a military bombing range; the results of this study provide the

Tooth erosion and eating disorders: a systematic review and meta-analysis.

Directory of Open Access Journals (Sweden)

Ana Paula Hermont

Full Text Available BACKGROUND: Eating disorders are associated with the highest rates of morbidity and mortality of any mental disorders among adolescents. The failure to recognize their early signs can compromise a patient's recovery and long-term prognosis. Tooth erosion has been reported as an oral manifestation that might help in the early detection of eating disorders. OBJECTIVES: The aim of this systematic review and meta-analysis was to search for scientific evidence regarding the following clinical question: Do eating disorders increase the risk of tooth erosion? METHODS: An electronic search addressing eating disorders and tooth erosion was conducted in eight databases. Two independent reviewers selected studies, abstracted information and assessed its quality. Data were abstracted for meta-analysis comparing tooth erosion in control patients (without eating disorders vs. patients with eating disorders; and patients with eating disorder risk behavior vs. patients without such risk behavior. Combined odds ratios (ORs and a 95% confidence interval (CI were obtained. RESULTS: Twenty-three papers were included in the qualitative synthesis and assessed by a modified version of the Newcastle-Ottawa Scale. Fourteen papers were included in the meta-analysis. Patients with eating disorders had more risk of tooth erosion (OR = 12.4, 95%CI = 4.1-37.5. Patients with eating disorders who self-induced vomiting had more risk of tooth erosion than those patients who did not self-induce vomiting (OR = 19.6, 95%CI = 5.6-68.8. Patients with risk behavior of eating disorder had more risk of tooth erosion than patients without such risk behavior (Summary OR = 11.6, 95%CI = 3.2-41.7. CONCLUSION: The scientific evidence suggests a causal relationship between tooth erosion and eating disorders and purging practices. Nevertheless, there is a lack of scientific evidence to fulfill the basic criteria of causation between the risk behavior for eating disorders and tooth erosion.

Erosion Pressure on the Danish Coasts

DEFF Research Database (Denmark)

Sørensen, Carlo Sass; Sørensen, Per; Kroon, Aart

Coastlines around the world are receding due to coastal erosion.With rising sea levels and a potential climatic deterioration due to climate change, erosion rates are likely to increase at many locations in the future.Together with the current preference of people to settle near or directly...... by the ocean, coastal erosion issues become increasingly more important to the human values at risk. Along many Danish coastlines, hard structures already act as coastal protection in the form of groins, breakwaters, revetments etc. These eroding coasts however still lack sand and where the public, in general......, neglects the need for sand replenishment i.e. in the form of repeated sand nourishments. Here we present a conceptual model and method for dividing coastal erosion into acute and chronic erosion pressure, respectively. We focus on the model use for management and climate change adaptation purposes...

Detection of soil erosion within pinyon-juniper woodlands using Thematic Mapper (TM) data

Science.gov (United States)

Price, Kevin P.

1993-01-01

Multispectral measurements collected by Landsat Thematic Mapper (TM) were correlated with field measurements, direct soil loss estimates, and Universal Soil Loss Equation (USLE) estimates to determine the sensitivity of TM data to varying degrees of soil erosion in pinyon-juniper woodland in central Utah. TM data were also evaluated as a predictor of the USLE Crop Management C factor for pinyon-juniper woodlands. TM spectral data were consistently better predictors of soil erosion factors than any combination of field factors. TM data were more sensitive to vegetation variations than the USLE C factor. USLE estimates showed low annual rates of erosion which varied little among the study sites. Direct measurements of rate of soil loss using the SEDIMENT (Soil Erosion DIrect measureMENT) technique, indicated high and varying rates of soil loss among the sites since tree establishment. Erosion estimates from the USLE and SEDIMENT methods suggest that erosion rates have been severe in the past, but because significant amounts of soil have already been eroded, and the surface is now armored by rock debris, present erosion rates are lower. Indicators of accelerated erosion were still present on all sites, however, suggesting that the USLE underestimated erosion within the study area.

Use of caesium-137 as a tracer of erosion and sedimentation: Handbook for the application of the caesium-137 technique. UK Overseas Development Administration research scheme R4579

Energy Technology Data Exchange (ETDEWEB)

Walling, D E; Quine, T A

1993-10-01

The caesium 137 technique has become an important tool for investigating soil erosion. It permits retrospective assessment of medium-term erosion rates. The application of the technique requires only one field visit, and the results can be provided within a relatively short time. The soil redistribution rates estimated represent an average for the last 30-35 years, and are therefore less influenced by extreme events. The rates estimated represent the sum of all erosive processes. Both rates and patterns of soil redistribution may be quantitatively assessed. A range of erosion estimates may be obtained, including mean rates of erosion and deposition and net rates of soil export from the field. The whole field may be studied without disturbance to the slope environment. The spatial resolution of the data obtained is defined by the sampling strategy. Chapters of part 1 discuss the basis of the {sup 137}Cs technique, the potential for its further development, and define a protocol for its application. Part 2 includes descriptions of case studies from China, Zimbabwe and Lesotho, which illustrate the value of the {sup 137}Cs technique in the assessment of soil erosion.

Use of caesium-137 as a tracer of erosion and sedimentation: Handbook for the application of the caesium-137 technique. UK Overseas Development Administration research scheme R4579

International Nuclear Information System (INIS)

Walling, D.E.; Quine, T.A.

1993-10-01

The caesium 137 technique has become an important tool for investigating soil erosion. It permits retrospective assessment of medium-term erosion rates. The application of the technique requires only one field visit, and the results can be provided within a relatively short time. The soil redistribution rates estimated represent an average for the last 30-35 years, and are therefore less influenced by extreme events. The rates estimated represent the sum of all erosive processes. Both rates and patterns of soil redistribution may be quantitatively assessed. A range of erosion estimates may be obtained, including mean rates of erosion and deposition and net rates of soil export from the field. The whole field may be studied without disturbance to the slope environment. The spatial resolution of the data obtained is defined by the sampling strategy. Chapters of part 1 discuss the basis of the 137 Cs technique, the potential for its further development, and define a protocol for its application. Part 2 includes descriptions of case studies from China, Zimbabwe and Lesotho, which illustrate the value of the 137 Cs technique in the assessment of soil erosion

Worldwide Experience with Erosion of the Magnetic Sphincter Augmentation Device.

Science.gov (United States)

Alicuben, Evan T; Bell, Reginald C W; Jobe, Blair A; Buckley, F P; Daniel Smith, C; Graybeal, Casey J; Lipham, John C

2018-04-17

The magnetic sphincter augmentation device continues to become a more common antireflux surgical option with low complication rates. Erosion into the esophagus is an important complication to recognize and is reported to occur at very low incidences (0.1-0.15%). Characterization of this complication remains limited. We aim to describe the worldwide experience with erosion of the magnetic sphincter augmentation device including presentation, techniques for removal, and possible risk factors. We reviewed data obtained from the device manufacturer Torax Medical, Inc., as well as the Manufacturer and User Facility Device Experience (MAUDE) database. The study period was from February 2007 through July 2017 and included all devices placed worldwide. In total, 9453 devices were placed and there were 29 reported cases of erosions. The median time to presentation of an erosion was 26 months with most occurring between 1 and 4 years after placement. The risk of erosion was 0.3% at 4 years after device implantation. Most patients experienced new-onset dysphagia prompting evaluation. Devices were successfully removed in all patients most commonly via an endoscopic removal of the eroded portion followed by a delayed laparoscopic removal of the remaining beads. At a median follow-up of 58 days post-removal, there were no complications and 24 patients have returned to baseline. Four patients reported ongoing mild dysphagia. Erosion of the LINX device is an important but rare complication to recognize that has been safely managed via minimally invasive approaches without long-term consequences.

How well does the Post-fire Erosion Risk Management Tool (ERMiT) really work?

Science.gov (United States)

Robichaud, Peter; Elliot, William; Lewis, Sarah; Miller, Mary Ellen

2016-04-01

The decision of where, when, and how to apply the most effective postfire erosion mitigation treatments requires land managers to assess the risk of damaging runoff and erosion events occurring after a fire. The Erosion Risk Management Tool (ERMiT) was developed to assist post fire assessment teams identify high erosion risk areas and effectiveness of various mitigation treatments to reduce that risk. ERMiT is a web-based application that uses the Water Erosion Prediction Project (WEPP) technology to estimate erosion, in probabilistic terms, on burned and recovering forest, range, and chaparral lands with and without the application of mitigation treatments. User inputs are processed by ERMiT to combine rain event variability with spatial and temporal variabilities of hillslope burn severity and soil properties which are then used as WEPP inputs. Since 2007, the model has been used in making hundreds of land management decisions in the US and elsewhere. We use eight published field study sites in the Western US to compare ERMiT predictions to observed hillslope erosion rates. Most sites experience only a few rainfall events that produced runoff and sediment except for a California site with a Mediterranean climate. When hillslope erosion occurred, significant correlations occurred between the observed hillslope erosion and those predicted by ERMiT. Significant correlation occurred for most mitigation treatments as well as the five recovery years. These model validation results suggest reasonable estimates of probabilistic post-fire hillslope sediment delivery when compared to observation.

Investigation of soil erosion in arable land in Hungary using radiotracer technique

International Nuclear Information System (INIS)

Dezsoe, Z.; Szabo, Sz.

2004-01-01

Quantitative data on long-term soil erosion rates on agricultural land are an essential requirement for the development of effective soil management and conservation strategies. Although several methods to estimate soil erosion exist, the use of 137 Cs and/or 210 Pb as fallout radionuclides for tracing soil movement overcomes many of the limitations of the traditional methods. Recently, the 137 Cs-technique has been widely accepted and is now commonly used for estimating the magnitude of soil loss. Long-term migration of 137 Cs in the Buekkzserc-Cserepfalu-Bogacs triangle area, at the foot of Buekk mountain (NE Hungary) was studied. The samples were analysed for 137 Cs by gamma spectrometry, using a calibrated high-resolution, low background HPGe coaxial detector. Migration of fallout nuclides in an undisturbed stable soil reflects the influence of a range of physico-chemical and biological processes operating in the soil system. (N.T.)

A "1"3"7Cs erosion model with moving boundary

International Nuclear Information System (INIS)

Yin, Chuan; Ji, Hongbing

2015-01-01

A novel quantitative model of the relationship between diffused concentration changes and erosion rates using assessment of soil losses was developed. It derived from the analysis of surface soil "1"3"7Cs flux variation under persistent erosion effect and based on the principle of geochemistry kinetics moving boundary. The new moving boundary model improves the basic simplified transport model (Zhang et al., 2008), and mainly applies to uniform rainfall areas which show a long-time soil erosion. The simulation results for this kind of erosion show under a long-time soil erosion, the influence of "1"3"7Cs concentration will decrease exponentially with increasing depth. Using the new model fit to the measured "1"3"7Cs depth distribution data in Zunyi site, Guizhou Province, China which has typical uniform rainfall provided a good fit with R"2 = 0.92. To compare the soil erosion rates calculated by the simple transport model and the new model, we take the Kaixian reference profile as example. The soil losses estimated by the previous simplified transport model are greater than those estimated by the new moving boundary model, which is consistent with our expectations. - Highlights: • The diffused moving boundary principle analysing "1"3"7Cs flux variation. • The new erosion model applies to uniform rainfall areas. • The erosion effect on "1"3"7Cs will decrease exponentially with increasing depth. • The new model provides two methods of calculating erosion rate.

Effect of flow velocity on erosion-corrosion behaviour of QSn6 alloy

Science.gov (United States)

Huang, Weijiu; Zhou, Yongtao; Wang, Zhenguo; Li, Zhijun; Zheng, Ziqing

2018-05-01

The erosion-corrosion behaviour of QSn6 alloy used as propellers in marine environment was evaluated by erosion-corrosion experiments with/without cathodic protection, electrochemical tests and scanning electron microscope (SEM) observations. The analysis was focused on the effect of flow velocity. The dynamic polarization curves showed that the corrosion rate of the QSn6 alloy increased as the flow velocity increased, due to the protective surface film removal at higher velocities. The lowest corrosion current densities of 1.26 × 10‑4 A cm‑2 was obtained at the flow velocity of 7 m s‑1. Because of the higher particle kinetic energies at higher flow velocity, the mass loss rate of the QSn6 alloy increased as the flow velocity increased. The mass loss rate with cathodic protection was lower than that without cathodic protection under the same conditions. Also, the lowest mass loss rate of 0.7 g m‑2 · h‑1 was acquired at the flow velocity of 7 m s‑1 with cathodic protection. However, the increase rate of corrosion rate and mass loss were decreased with increasing the flow velocity. Through observation the SEM morphologies of the worn surfaces, the main wear mechanism was ploughing with/without cathodic protection. The removal rates of the QSn6 alloy increased as the flow velocity increased in both pure erosion and erosion-corrosion, whereas the erosion and corrosion intensified each other. At the flow velocity of 7 m s‑1, the synergy rate (ΔW) exceeded by 5 times the erosion rate (Wwear). Through establishment and observation the erosion-corrosion mechanism map, the erosion-corrosion was the dominant regime in the study due to the contribution of erosion on the mass loss rate exceeded the corrosion contribution. The QSn6 alloy with cathodic protection is feasible as propellers, there are higher security at lower flow velocity, such as the flow velocity of 7 m s‑1 in the paper.

Potential for erosion corrosion of SRS high level waste tanks

International Nuclear Information System (INIS)

Zapp, P.E.

1994-01-01

SRS high-level radioactive waste tanks will not experience erosion corrosion to any significant degree during slurry pump operations. Erosion corrosion in carbon steel structures at reported pump discharge velocities is dominated by electrochemical (corrosion) processes. Interruption of those processes, as by the addition of corrosion inhibitors, sharply reduces the rate of metal loss from erosion corrosion. The well-inhibited SRS waste tanks have a near-zero general corrosion rate, and therefore will be essentially immune to erosion corrosion. The experimental data on carbon steel erosion corrosion most relevant to SRS operations was obtained at the Hanford Site on simulated Purex waste. A metal loss rate of 2.4 mils per year was measured at a temperature of 102 C and a slurry velocity comparable to calculated SRS slurry velocities on ground specimens of the same carbon steel used in SRS waste tanks. Based on these data and the much lower expected temperatures, the metal loss rate of SRS tanks under waste removal and processing conditions should be insignificant, i.e. less than 1 mil per year

Identification of soil erosion risk areas for conservation planning in different states of India.

Science.gov (United States)

Sharda, V N; Mandal, Debashis; Ojasvi, P R

2013-03-01

Assessment of soil erosion risks, especially in the developing countries, is a challenging task mainly due to non-availability or insufficiency of relevant data. In this paper, the soil erosion risks have been estimated by integrating the spatial data on potential erosion rates and soil loss tolerance limits for conservation planning at state level in India. The erosion risk classes have been prioritized based upon the difference between the prevailing erosion rates and the permissible erosion limits. The analysis revealed that about 50% of total geographical area (TGA) of India, falling in five priority erosion risk classes, requires different intensity of conservation measures though about 91% area suffers from potential erosion rates varying from 40 t ha(-1) yr(-1). Statewise analysis indicated that Andhra Pradesh, Maharashtra and Rajasthan share about 75% of total area under priority Class 1 (6.4 M ha) though they account for only 19.4% of the total area (36.2 M ha) under very severe potential erosion rate category (> 40 t ha(-1)yr(-1)). It was observed that about 75% of total geographical area (TGA) in the states of Bihar, Gujarat, Haryana, Kerala and Punjab does not require any specific soil conservation measure as the potential erosion rates are well within the tolerance limits. The developed methodology can be successfully employed for prioritization of erosion risk areas at watershed, region or country level.

Soil erosion and sediment fluxes analysis: a watershed study of the Ni Reservoir, Spotsylvania County, VA, USA.

Science.gov (United States)

Pope, Ian C; Odhiambo, Ben K

2014-03-01

Anthropogenic forces that alter the physical landscape are known to cause significant soil erosion, which has negative impact on surface water bodies, such as rivers, lakes/reservoirs, and coastal zones, and thus sediment control has become one of the central aspects of catchment management planning. The revised universal soil loss equation empirical model, erosion pins, and isotopic sediment core analyses were used to evaluate watershed erosion, stream bank erosion, and reservoir sediment accumulation rates for Ni Reservoir, in central Virginia. Land-use and land cover seems to be dominant control in watershed soil erosion, with barren land and human-disturbed areas contributing the most sediment, and forest and herbaceous areas contributing the least. Results show a 7 % increase in human development from 2001 (14 %) to 2009 (21.6 %), corresponding to an increase in soil loss of 0.82 Mg ha(-1) year(-1) in the same time period. (210)Pb-based sediment accumulation rates at three locations in Ni Reservoir were 1.020, 0.364, and 0.543 g cm(-2) year(-1) respectively, indicating that sediment accumulation and distribution in the reservoir is influenced by reservoir configuration and significant contributions from bedload. All three locations indicate an increase in modern sediment accumulation rates. Erosion pin results show variability in stream bank erosion with values ranging from 4.7 to 11.3 cm year(-1). These results indicate that urban growth and the decline in vegetative cover has increased sediment fluxes from the watershed and poses a significant threat to the long-term sustainability of the Ni Reservoir as urbanization continues to increase.

Monthly Rainfall Erosivity Assessment for Switzerland

Science.gov (United States)

Schmidt, Simon; Meusburger, Katrin; Alewell, Christine

2016-04-01

Water erosion is crucially controlled by rainfall erosivity, which is quantified out of the kinetic energy of raindrop impact and associated surface runoff. Rainfall erosivity is often expressed as the R-factor in soil erosion risk models like the Universal Soil Loss Equation (USLE) and its revised version (RUSLE). Just like precipitation, the rainfall erosivity of Switzerland has a characteristic seasonal dynamic throughout the year. This inter-annual variability is to be assessed by a monthly and seasonal modelling approach. We used a network of 86 precipitation gauging stations with a 10-minute temporal resolution to calculate long-term average monthly R-factors. Stepwise regression and Monte Carlo Cross Validation (MCCV) was used to select spatial covariates to explain the spatial pattern of R-factor for each month across Switzerland. The regionalized monthly R-factor is mapped by its individual regression equation and the ordinary kriging interpolation of its residuals (Regression-Kriging). As covariates, a variety of precipitation indicator data has been included like snow height, a combination of hourly gauging measurements and radar observations (CombiPrecip), mean monthly alpine precipitation (EURO4M-APGD) and monthly precipitation sums (Rhires). Topographic parameters were also significant explanatory variables for single months. The comparison of all 12 monthly rainfall erosivity maps showed seasonality with highest rainfall erosivity in summer (June, July, and August) and lowest rainfall erosivity in winter months. Besides the inter-annual temporal regime, a seasonal spatial variability was detectable. Spatial maps of monthly rainfall erosivity are presented for the first time for Switzerland. The assessment of the spatial and temporal dynamic behaviour of the R-factor is valuable for the identification of more susceptible seasons and regions as well as for the application of selective erosion control measures. A combination with monthly vegetation

Assessing catchment-scale erosion and yields of suspended solids from improved temperate grassland.

Science.gov (United States)

Bilotta, G S; Krueger, T; Brazier, R E; Butler, P; Freer, J; Hawkins, J M B; Haygarth, P M; Macleod, C J A; Quinton, J N

2010-03-01

This paper quantifies the yields of suspended solids (SS) from a headwater catchment managed as improved temperate grassland, providing the first direct, catchment-scale evidence of the rates of erosion from this land-use in the UK and assessing the threat posed to aquatic ecosystems. High-resolution monitoring of catchment hydrology and the concentrations of SS and volatile organic matter (VOM) were carried out in the first-order channel of the Den Brook headwater catchment in Devon (UK) during the 2006-2007 hydrological season. The widely used 'rating curve' (discharge-concentration) approach was employed to estimate yields of SS, but as demonstrated by previous researchers, this study showed that discharge is a poor predictor of SS concentrations and therefore any yields estimated from this technique are likely to be highly uncertain. Nevertheless, for the purpose of providing estimates of yields that are comparable to previous studies on other land uses/sources, this technique was adopted albeit in an uncertainty-based framework. The findings suggest that contrary to the common perception, grasslands can be erosive landscapes with SS yields from this catchment estimated to be between 0.54 and 1.21 t ha(-1) y(-1). In terms of on-site erosion problems, this rate of erosion does not significantly exceed the commonly used 'tolerable' threshold in the UK ( approximately 1 t ha(-1) y(-1)). In terms of off-site erosion problems, it is argued here that the conventional expression of SS yield as a bulk annual figure has little relevance to the water quality and ecological status of surface waters and therefore an alternative technique (the concentration-frequency curve) is developed within this paper for the specific purpose of assessing the ecological threat posed by the delivery of SS into surface waters. This technique illustrates that concentrations of SS recorded at the catchment outlet frequently exceed the water quality guidelines, such as those of the EU

Predicting coastal cliff erosion using a Bayesian probabilistic model

Science.gov (United States)

Hapke, Cheryl J.; Plant, Nathaniel G.

2010-01-01

Regional coastal cliff retreat is difficult to model due to the episodic nature of failures and the along-shore variability of retreat events. There is a growing demand, however, for predictive models that can be used to forecast areas vulnerable to coastal erosion hazards. Increasingly, probabilistic models are being employed that require data sets of high temporal density to define the joint probability density function that relates forcing variables (e.g. wave conditions) and initial conditions (e.g. cliff geometry) to erosion events. In this study we use a multi-parameter Bayesian network to investigate correlations between key variables that control and influence variations in cliff retreat processes. The network uses Bayesian statistical methods to estimate event probabilities using existing observations. Within this framework, we forecast the spatial distribution of cliff retreat along two stretches of cliffed coast in Southern California. The input parameters are the height and slope of the cliff, a descriptor of material strength based on the dominant cliff-forming lithology, and the long-term cliff erosion rate that represents prior behavior. The model is forced using predicted wave impact hours. Results demonstrate that the Bayesian approach is well-suited to the forward modeling of coastal cliff retreat, with the correct outcomes forecast in 70–90% of the modeled transects. The model also performs well in identifying specific locations of high cliff erosion, thus providing a foundation for hazard mapping. This approach can be employed to predict cliff erosion at time-scales ranging from storm events to the impacts of sea-level rise at the century-scale.

Cavitation erosion of silver plated coating at different temperatures and pressures

Energy Technology Data Exchange (ETDEWEB)

Hattori, Shuji; Motoi, Yoshihiro [Graduate School of Engineering, University of Fukui, 3-9-1 Bunkyo, Fuku-shi, Fukui 910-8507 (Japan); Kikuta, Kengo; Tomaru, Hiroshi [IHI Corperation, TOYOSU IHI BUILDING, 1-1, Toyosu 3-chome, Koto-ku, Tokyo 1358710 (Japan)

2014-04-11

Cavitation often occurs in inducer pumps used for space rockets. Silver plated coating on the inducer liner faces the damage of cavitation. Therefore, it is important to study about the cavitation erosion resistance for silver plated coating at several operating conditions in the inducer pumps. In this study, the cavitation erosion tests were carried for silver plated coating in deionized water and ethanol at several liquid temperatures (273K–400K) and pressures (0.10MPa–0.48MPa). The mass loss rate is evaluated in terms of thermodynamic parameter Σ proposed by Brennen [9], suppression pressure p–p{sub v} (p{sub v}: saturated vapor pressure) and acoustic impedance ρc (ρ: density and c: sound speed). Cavitation bubble behaviors depending on the thermodynamic effect and the liquid type were observed by high speed video camera. The mass loss rate is formulated by thermodynamic parameter Σ, suppression pressure p–p{sub v} and acoustic impedance ρc.

Land susceptibility to soil erosion in Orashi Catchment, Nnewi South, Anambra State, Nigeria

Science.gov (United States)

Odunuga, Shakirudeen; Ajijola, Abiodun; Igwetu, Nkechi; Adegun, Olubunmi

2018-02-01

Soil erosion is one of the most critical environmental hazards that causes land degradation and water quality challenges. Specifically, this phenomenon has been linked, among other problems, to river sedimentation, groundwater pollution and flooding. This paper assesses the susceptibility of Orashi River Basin (ORB) to soil erosion for the purpose of erosion control measures. Located in the South Eastern part of Nigeria, the ORB which covers approximately 413.61 km2 is currently experiencing one of the fastest population growth rate in the region. Analysis of the soil erosion susceptibility of the basin was based on four factors including; rainfall, Land use/Land cover change (LULC), slope and soil erodibility factor (k). The rainfall was assumed to be a constant and independent variable, slope and soil types were categorised into ten (10) classes each while the landuse was categorised into five classes. Weight was assigned to the classes based on the degree of susceptibility to erosion. An overlay of the four variables in a GIS environment was used to produce the basin susceptibility to soil erosion. This was based on the weight index of each factors. The LULC analysis revealed that built-up land use increased from 26.49 km2 (6.4 %) in year 1980 to 79.24 km2 (19.16 %) in 2015 at an average growth rate of 1.51 km2 per annum while the light forest decreased from 336.41 km2 (81.33 %) in 1980 to 280.82 km2 (67.89 %) in 2015 at an average rate 1.59 km2 per annum. The light forest was adjudged to have the highest land cover soil erosion susceptibility. The steepest slope ranges between 70 and 82° (14.34 % of the total land area) and was adjudged to have the highest soil susceptibility to erosion. The total area covered of the loamy soil is 112.37 km2 (27.07 %) with erodibility of 0.7. In all, the overlay of all the variables revealed that 106.66 km2 (25.70 %) and 164.80 km2 (39.7 %) of the basin has a high and very high susceptibility to soil erosion. The over 50

Soil erosion in a man-made landscape: the Mediterranean

Science.gov (United States)

Cerdà, A.; Ruiz Sinoga, J. D.; Cammeraat, L. H.

2012-04-01

Mediterranean-type ecosystems are characterised by a seasonally contrasted distribution of precipitation, by the coincidence of the driest and hottest season in summer, by an often-mountainous terrain, and by a long history of intense human occupation, especially around the Mediterranean Sea. The history of the Mediterranean lands is the history of human impacts on the soil system, and soil erosion is the most intense and widespread impact on this land where high intensity and uneven rainfall is found. A review of the soil erosion rates measured in the Mediterranean basin will be shown. The measurements done by means of erosion pins, topographical measurements, rainfall simulators, Gerlach collectors in open or close plots, watershed/basin measurements, reservoirs siltation and historical data will be shown. A review of the soil erosion models applied in the Mediterranean will be shown. The tentative approach done until October 2011 show that the soil erosion rates on Mediterranean type ecosystems are not as high as was supposed by the pioneers in the 70's. And this is probably due to the fact that the soils are very shallow and sediments are not available after millennia of high erosion rates. This is related to the large amount of rock fragments are covering the soil, and the rock outcrops that are found in the upper slope trams and the summits. Soil erosion in the Mediterranean is seasonal due to the rainfall concentration in winter, and highly variable within years as the high intensity rainfall events control the sediment production. Natural vegetation is adapted to the Mediterranean environmental conditions, and they are efficient to control the soil losses. An example are the forest fire that increase the soil losses but this is a temporal change as after 2-4 years the soil erosion rates are similar to the pre-fire period. Agriculture lands are the source of sediments although the highest erosion rates are found in badland areas that cover a small part of

Solid Particle Erosion of Date Palm Leaf Fiber Reinforced Polyvinyl Alcohol Composites

Directory of Open Access Journals (Sweden)

Jyoti R. Mohanty

2014-01-01

Full Text Available Solid particle erosion behavior of short date palm leaf (DPL fiber reinforced polyvinyl alcohol (PVA composite has been studied using silica sand particles (200 ± 50 μm as an erodent at different impingement angles (15–90° and impact velocities (48–109 m/s. The influence of fiber content (wt% of DPL fiber on erosion rate of PVA/DPL composite has also been investigated. The neat PVA shows maximum erosion rate at 30° impingement angle whereas PVA/DPL composites exhibit maximum erosion rate at 45° impingement angle irrespective of fiber loading showing semiductile behavior. The erosion efficiency of PVA and its composites varies from 0.735 to 16.289% for different impact velocities studied. The eroded surfaces were observed under scanning electron microscope (SEM to understand the erosion mechanism.

Cavitation erosion - scale effect and model investigations

Science.gov (United States)

Geiger, F.; Rutschmann, P.

2015-12-01

The experimental works presented in here contribute to the clarification of erosive effects of hydrodynamic cavitation. Comprehensive cavitation erosion test series were conducted for transient cloud cavitation in the shear layer of prismatic bodies. The erosion pattern and erosion rates were determined with a mineral based volume loss technique and with a metal based pit count system competitively. The results clarified the underlying scale effects and revealed a strong non-linear material dependency, which indicated significantly different damage processes for both material types. Furthermore, the size and dynamics of the cavitation clouds have been assessed by optical detection. The fluctuations of the cloud sizes showed a maximum value for those cavitation numbers related to maximum erosive aggressiveness. The finding suggests the suitability of a model approach which relates the erosion process to cavitation cloud dynamics. An enhanced experimental setup is projected to further clarify these issues.

Thermal erosion of a permafrost coastline: Improving process-based models using time-lapse photography

Science.gov (United States)

Wobus, C.; Anderson, R.; Overeem, I.; Matell, N.; Clow, G.; Urban, F.

2011-01-01

Coastal erosion rates locally exceeding 30 m y-1 have been documented along Alaska's Beaufort Sea coastline, and a number of studies suggest that these erosion rates have accelerated as a result of climate change. However, a lack of direct observational evidence has limited our progress in quantifying the specific processes that connect climate change to coastal erosion rates in the Arctic. In particular, while longer ice-free periods are likely to lead to both warmer surface waters and longer fetch, the relative roles of thermal and mechanical (wave) erosion in driving coastal retreat have not been comprehensively quantified. We focus on a permafrost coastline in the northern National Petroleum Reserve-Alaska (NPR-A), where coastal erosion rates have averaged 10-15 m y-1 over two years of direct monitoring. We take advantage of these extraordinary rates of coastal erosion to observe and quantify coastal erosion directly via time-lapse photography in combination with meteorological observations. Our observations indicate that the erosion of these bluffs is largely thermally driven, but that surface winds play a crucial role in exposing the frozen bluffs to the radiatively warmed seawater that drives melting of interstitial ice. To first order, erosion in this setting can be modeled using formulations developed to describe iceberg deterioration in the open ocean. These simple models provide a conceptual framework for evaluating how climate-induced changes in thermal and wave energy might influence future erosion rates in this setting.

Erosion protection of uranium tailings impoundments

International Nuclear Information System (INIS)

Walters, W.H.; Skaggs, R.L.; Foley, M.G.; Beedlow, P.A.

1986-09-01

Pacific Northwest Laboratory (PNL) prepared this report to assist in the design and review of erosion protection works for decommissioned uranium tailings impoundments. The major causes of erosion over the long-term decommissioning period are from rainfall-runoff (overland flow) and stream channel flooding. The method of protection recommended for the impoundment side slopes and site drainage channels is rock riprap. Combinations of vegetation and rock mulch are recommended for the top surface. The design methods were developed from currently available procedures supplemented by field, laboratory, and mathematical model studies performed by PNL. Guidelines for the placement of riprap, inspection, and maintenance are presented. Other subjects discussed are rock selection and testing, slope stability, and overland erosion modeling

Mountain erosion over 10 yr, 10 k.y., and 10 m.y. time scales

Science.gov (United States)

James W. Kirchner; Robert C. Finkel; Clifford S. Riebe; Darryl E. Granger; James L. Clayton; John G. King; Walter F. Megahan

2001-01-01

We used cosmogenic 10Be to measure erosion rates over 10 k.y. time scales at 32 Idaho mountain catchments, ranging from small experimental watersheds (0.2 km2) to large river basins (35 000 km2). These long-term sediment yields are, on average, 17 times higher than stream sediment fluxes measured over...

Designing a national soil erosion monitoring network for England and Wales

Science.gov (United States)

Lark, Murray; Rawlins, Barry; Anderson, Karen; Evans, Martin; Farrow, Luke; Glendell, Miriam; James, Mike; Rickson, Jane; Quine, Timothy; Quinton, John; Brazier, Richard

2014-05-01

Although soil erosion is recognised as a significant threat to sustainable land use and may be a priority for action in any forthcoming EU Soil Framework Directive, those responsible for setting national policy with respect to erosion are constrained by a lack of robust, representative, data at large spatial scales. This reflects the process-orientated nature of much soil erosion research. Recognising this limitation, The UK Department for Environment, Food and Rural Affairs (Defra) established a project to pilot a cost-effective framework for monitoring of soil erosion in England and Wales (E&W). The pilot will compare different soil erosion monitoring methods at a site scale and provide statistical information for the final design of the full national monitoring network that will: provide unbiased estimates of the spatial mean of soil erosion rate across E&W (tonnes ha-1 yr-1) for each of three land-use classes - arable and horticultural grassland upland and semi-natural habitats quantify the uncertainty of these estimates with confidence intervals. Probability (design-based) sampling provides most efficient unbiased estimates of spatial means. In this study, a 16 hectare area (a square of 400 x 400 m) positioned at the centre of a 1-km grid cell, selected at random from mapped land use across E&W, provided the sampling support for measurement of erosion rates, with at least 94% of the support area corresponding to the target land use classes. Very small or zero erosion rates likely to be encountered at many sites reduce the sampling efficiency and make it difficult to compare different methods of soil erosion monitoring. Therefore, to increase the proportion of samples with larger erosion rates without biasing our estimates, we increased the inclusion probability density in areas where the erosion rate is likely to be large by using stratified random sampling. First, each sampling domain (land use class in E&W) was divided into strata; e.g. two sub

Electrode erosion in arc discharges at atmospheric pressure

Science.gov (United States)

Hardy, T. L.

1985-01-01

An experimental investigation was performed in an effort to measure and increase lifetime of electrodes in an arcjet thruster. The electrode erosion of various anode and cathode materials was measured after tests in an atmospheric pressure nitrogen arc discharge at powers less than 1 kW. A free-burning arc configuration and a constricted arc configuration were used to test the materials. Lanthanum hexboride and thoriated tungsten had low cathode erosion rates while thoriated tungsten and pure tungsten had the lowest anode erosion rates of the materials tested. Anode cooling, reverse gas flow, an external magnetic fields were all found to reduce electrode mass loss.

A comparison of methods in estimating soil water erosion

Directory of Open Access Journals (Sweden)

Marisela Pando Moreno

2012-02-01

Full Text Available A comparison between direct field measurements and predictions of soil water erosion using two variant; (FAO and R/2 index of the Revised Universal Soil Loss Equation (RUSLE was carried out in a microcatchment o 22.32 km2 in Northeastern Mexico. Direct field measurements were based on a geomorphologic classification of the area; while environmental units were defined for applying the equation. Environmental units were later grouped withir geomorphologic units to compare results. For the basin as a whole, erosion rates from FAO index were statistical!; equal to those measured on the field, while values obtained from the R/2 index were statistically different from the res and overestimated erosion. However, when comparing among geomorphologic units, erosion appeared overestimate! in steep units and underestimated in more flat areas. The most remarkable differences on erosion rates, between th( direct and FAO methods, were for those units where gullies have developed, fn these cases, erosion was underestimated by FAO index. Hence, it is suggested that a weighted factor for presence of gullies should be developed and included in RUSLE equation.

Protection of uranium tailings impoundments against overland erosion

International Nuclear Information System (INIS)

Walters, W.H.; Skaggs, R.L.

1986-01-01

This study investigates the problems involved in designing protection methods to prevent erosion of a uranium tailings impoundment cover from rainfall and runoff (overland flow) processes. The study addresses the side slopes and top surface as separate elements. The side slopes are more subject to gully erosion and require absolute protection such as that provided by rock riprap. The flatter top surface needs much less protection (vegetation/rock combinations) but some estimate of erosion rates are needed to compare alternatives. A literature review indicated that, currently, procedures are not available for the design of rock riprap to prevent gully erosion. Therefore, rock protection on the side slope will have to be based upon engineering judgment determined by the particular site conditions. The Manning-kinetic equations (velocity and depth of runoff) were investigated as a possible aid to the design of gully erosion protection. Guidelines are suggested for the use of rock riprap to prevent gully erosion. Three mathematical models were used to compute erosion rates for the top surface of a hypothetical tailings impoundment. The results recommend that one or possibly both of the regression models could be used to evaluate preliminary protection designs for the top surface. A physical process simulation model should be used for the final design. 30 refs., 13 figs., 16 tabs

The Arctic Coastal Erosion Problem

Energy Technology Data Exchange (ETDEWEB)

Frederick, Jennifer M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Thomas, Matthew Anthony [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bull, Diana L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Craig A. [Integral Consulting Inc., San Francisco, CA (United States); Roberts, Jesse D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-09-01

Permafrost-dominated coastlines in the Arctic are rapidly disappearing. Arctic coastal erosion rates in the United States have doubled since the middle of the twentieth century and appear to be accelerating. Positive erosion trends have been observed for highly-variable geomorphic conditions across the entire Arctic, suggesting a major (human-timescale) shift in coastal landscape evolution. Unfortunately, irreversible coastal land loss in this region poses a threat to native, industrial, scientific, and military communities. The Arctic coastline is vast, spanning more than 100,000 km across eight nations, ten percent of which is overseen by the United States. Much of area is inaccessible by all-season roads. People and infrastructure, therefore, are commonly located near the coast. The impact of the Arctic coastal erosion problem is widespread. Homes are being lost. Residents are being dispersed and their villages relocated. Shoreline fuel storage and delivery systems are at greater risk. The U.S. Department of Energy (DOE) and Sandia National Laboratories (SNL) operate research facilities along some of the most rapidly eroding sections of coast in the world. The U.S. Department of Defense (DOD) is struggling to fortify coastal radar sites, operated to ensure national sovereignty in the air, against the erosion problem. Rapid alterations to the Arctic coastline are facilitated by oceanographic and geomorphic perturbations associated with climate change. Sea ice extent is declining, sea level is rising, sea water temperature is increasing, and permafrost state is changing. The polar orientation of the Arctic exacerbates the magnitude and rate of the environmental forcings that facilitate coastal land area loss. The fundamental mechanics of these processes are understood; their non-linear combination poses an extreme hazard. Tools to accurately predict Arctic coastal erosion do not exist. To obtain an accurate predictive model, a coupling of the influences of

The 7Be profiles in the undisturbed soil used for reference site to estimate the soil erosion

International Nuclear Information System (INIS)

Raksawong, S; Bhongsuwan, T; Krmar, M

2017-01-01

The cosmogenic radionuclide 7 Be is increasingly used to obtain information on event-related soil erosion rates within agricultural landscapes. In this study, we select two undisturbed and flat areas to calculate the reference inventory and relaxation mass depth by using 7 Be technique to document short-term erosion. Our results showed that the depth distribution of 7 Be in undisturbed soil profiles was 1.0 cm in sites S02 and S03; the initial activities were 31.6 and 38.8 Bq.kg -1 , respectively. The relaxation mass depths were 5.4 and 7.2 kg.m -2 and the measured reference 7 Be inventories were 71 and 110 Bq.m -2 for sites S02 and S03, respectively. The difference values of the relaxation mass depth and the reference inventory of both sites implied that for determining a short term soil erosion using 7 Be, the reference site was suggested to be selected as close as possible to the study site. (paper)

Deforestation Effects on Soil Erosion in the Lake Kivu Basin, D.R. Congo-Rwanda

Directory of Open Access Journals (Sweden)

Fidele Karamage

2016-11-01

Full Text Available Deforestation and natural grassland conversion to agricultural land use constitute a major threat to soil and water conservation. This study aimed at assessing the status of land cover and land use (LCLU in the Lake Kivu basin, and its related impacts in terms of soil erosion by water using the Universal Soil Erosion Equation (USLE model. The results indicated that the Lake Kivu basin is exposed to soil erosion risk with a mean annual rate of 30 t·ha−1, and only 33% of the total non-water area is associated with a tolerable soil loss (≤10 t·ha−1·year−1. Due to both natural factors (abundant tropical precipitation and steep slopes and anthropogenic activities without prior appropriate conservation practices, all land-use types—namely settlement, cropland, forestland, and grassland—are exposed to a severe mean erosion rate of 41 t·ha−1·year−1, 31 t·ha−1·year−1, 28 t·ha−1·year−1, and 20 t·ha−1·year−1, respectively. The cropland that occupied 74% of the non-water area in 2015 was the major contributor (75% to the total annual soil loss in the Lake Kivu basin. This study showed that conservation practices in the cropland cells would result in a mean erosion rate of 7 t·ha−1·year−1, 18 t·ha−1·year−1, and 35 t·ha−1·year−1 for terracing, strip-cropping, and contouring, respectively. The adoption of terracing would be the best conservation practice, among others, that could reduce soil erosion in cropland areas up to about 23%. The erosion risk minimization in forests and grasslands implies an increase in overstorey canopy and understorey vegetation, and control of human activities such as fires, mining, soil compaction from domestic animals grazing, and so on. Soil erosion control in settled areas suggests, among other things, the revegetation of construction sites, establishment of outlet channels, rainfall water harvesting systems, and pervious paving block with grass.

7 CFR 1714.6 - Interest rate term.

Science.gov (United States)

2010-01-01

... 7 Agriculture 11 2010-01-01 2010-01-01 false Interest rate term. 1714.6 Section 1714.6 Agriculture... PRE-LOAN POLICIES AND PROCEDURES FOR INSURED ELECTRIC LOANS General § 1714.6 Interest rate term. (a) Municipal rate loans. Selection of interest rate terms shall be made by the borrower for each advance of...

Using REE tracers to measure sheet erosion changing to rill erosion

International Nuclear Information System (INIS)

Liu Puling; Xue Yazhou; Song Wei; Wang Mingyi; Ju Tongjun

2004-01-01

Rare Earth Elements (REE) tracer method was used to study sheet erosion changing to rill erosion on slope land. By placing different rare earth elements of different soil depth across a slope in an indoor plot, two simulated rainfalls were applied to study the change of erosion type and the rill erosion process. The results indicate that the main erosion type is sheet erosion at the beginning of the rainfalls, and serious erosion happens after rill erosion appears. Accumulated sheet and rill erosion amounts increase with the rainfalls time. The percentage of sheet erosion amount decreases and rill erosion percentage increases with time. At the end of the rainfalls, the total rill erosion amounts are 4-5 times more than sheet erosion. In this paper, a new REE tracer method was used to quantitatively distinguish sheet and rill erosion amounts. The new REE tracer method should be useful to future studying of erosion processes on slope lands. (authors)

Quantifying erosion over timescales of one million years: A photogrammetric approach on the amount of Rhenish erosion in southwestern Germany

Science.gov (United States)

Strasser, Annette; Strasser, Marcel; Seyfried, Hartmut

2010-10-01

The Lein valley in southwestern Germany possesses well-preserved Pliocene to mid Pleistocene land surfaces featuring a gentle relief and sediments accumulated by former tributaries of the Danube. This ancient Danubian land surface was captured and incised by mid Pleistocene to Holocene tributaries of the River Rhine. In a photogrammetric approach we calculated the volume of material extracted by Rhenish erosion providing a first quantification of the effects of stream piracy on timescales of about 1 Ma. Using stereoscopic surface modelling software a DEM was generated with a resolution of 5 m. From borehole data, literature, geological maps, and own field observations we determined the morphometric parameters of the ancient Danubian Ur-Lein valley. The gradient was imported as a 3D-breakline into the model where it controls the reinterpolation of surrounding data points. The result is a high-resolution DEM of the valley of the Ur-Lein. Subtraction of the DEM of the actual landscape from the DEM of the ancient Ur-Lein valley yields a model representing the rock volume eroded by the Rhenish Lein which totals 1.39 km 3 and converts into a rate of erosion between 63 and 74 mm/ka over a period of 700 to 600 ka, respectively, in accordance with figures obtained elsewhere in Central Europe through cosmogenic nuclides. It reflects the dominance of frequent fluctuations in climate and is considered to be mainly a product of strong changes in temperature and related processes during the transitional times between mid to late Pleistocene warm and cold states. A filtering procedure applied to cold and transitional state erosion rates of the Middle and Late Pleistocene yielded peak values between 66 and 77 mm/ka, up to three times higher than the modern rate or the rate of warm-state episodes. An assessment of the contribution of Rhenish stream piracy on long-term mid Pleistocene denudation under changing climate conditions resulted in a maximum 4.9-fold acceleration.

Estimates of soil erosion using cesium-137 tracer models.

Science.gov (United States)

Saç, M M; Uğur, A; Yener, G; Ozden, B

2008-01-01

The soil erosion was studied by 137Cs technique in Yatagan basin in Western Turkey, where there exist intensive agricultural activities. This region is subject to serious soil loss problems and yet there is not any erosion data towards soil management and control guidelines. During the soil survey studies, the soil profiles were examined carefully to select the reference points. The soil samples were collected from the slope facets in three different study areas (Kirtas, Peynirli and Kayisalan Hills). Three different models were applied for erosion rate calculations in undisturbed and cultivated sites. The profile distribution model (PDM) was used for undisturbed soils, while proportional model (PM) and simplified mass balance model (SMBM) were used for cultivated soils. The mean annual erosion rates found using PDM in undisturbed soils were 15 t ha(-1) year(-1) at the Peynirli Hill and 27 t ha(-1) year(-1) at the Kirtas Hill. With the PM and SMBM in cultivated soils at Kayişalan, the mean annual erosion rates were obtained to be 65 and 116 t ha(-1) year(-1), respectively. The results of 137Cs technique were compared with the results of the Universal Soil Loss Equation (USLE).

Use of Magnetic Parameters to Asses Soil Erosion Rates on Agricultural Site

Science.gov (United States)

Petrovsky, E.; Kapicka, A.; Dlouha, S.; Jaksik, O.; Grison, H.; Kodesova, R.

2014-12-01

A detailed field study on a small test site of agricultural land situated in loess region in Southern Moravia (Czech Republic) and laboratory analyses were carried out in order to test the applicability of magnetic methods in assessing soil erosion. Haplic Chernozem, the original dominant soil unit in the area, is nowadays progressively transformed into different soil units along with intense soil erosion. As a result, an extremely diversified soil cover structure has developed due to the erosion. The site was characterized by a flat upper part while the middle part, formed by a substantive side valley, is steeper. We carried out field measurements of magnetic susceptibility on a regular grid, resulting in 101 data points. The bulk soil material for laboratory investigation was gathered from all the grid points. Values of the magnetic susceptibility are spatially distributed depending on the terrain. Higher values were measured in the flat upper part (where the original top horizon remained). The lowest values of were obtained on the steep valley sides. Here the original topsoil was eroded and mixed by tillage with the soil substrate (loess). A soil profile unaffected by erosion was investigated in detail. The vertical distribution of magnetic susceptibility along this "virgin" profile was measured in laboratory on the samples collected with 2-cm spacing. The undisturbed profile shows several soil horizons. Horizons Ac and A show a slight increase in magnetic susceptibility up to a depth of about 70 cm. Horizon A/Ck is characterized by a decrease in susceptibility, and the underlying C horizon (h > 103 cm) has a very low value of magnetic susceptibility. The differences between the values of susceptibility in the undisturbed soil profile and the magnetic signal after uniform mixing the soil material as a result of tillage and erosion are fundamental for the estimation of soil loss in the studied test field. Using the uneroded profile from the studied locality as a

CFD Based Erosion Modelling of Abrasive Waterjet Nozzle using Discrete Phase Method

International Nuclear Information System (INIS)

Kamarudin, Naqib Hakim; Prasada Rao, A K; Azhari, Azmir

2016-01-01

In Abrasive Waterjet (AWJ) machining, the nozzle is the most critical component that influences the performance, precision and economy. Exposure to a high speed jet and abrasives makes it susceptible to wear erosion which requires for frequent replacement. The present works attempts to simulate the erosion of the nozzle wall using computational fluid dynamics. The erosion rate of the nozzle was simulated under different operating conditions. The simulation was carried out in several steps which is flow modelling, particle tracking and erosion rate calculation. Discrete Phase Method (DPM) and K-ε turbulence model was used for the simulation. Result shows that different operating conditions affect the erosion rate as well as the flow interaction of water, air and abrasives. The simulation results correlates well with past work. (paper)

CFD evaluation of erosion rate around a bridge near a sand dune

Science.gov (United States)

He, Wei; Huang, Ning; Dun, Hongchao; Wang, Wenbo

2017-04-01

This study performs a series of simulations through solving the Navier-Stokes equations and the RNG k-ε turbulence model to investigate the wind erosion rates around a bridge in a desert area with sand dunes. The digital elevation model of sand dunes and the bridge model are obtained respectively from hypsographic map and construction drawings. Through combining them into the CFD software of Fluent the simulation zone was formed. The data of wind speed obtained from field observation is fitted into a logarithm format, which was imported into Fluent model as a inlet wind speed condition. Then, the effect of Dun-Go railway on wind-blown sand movement of the neighbouring environment is simulated. The results exhibit that affected by both the sand dune and bridge, the flow field is in a complex condition. It is also shown that the bridge in upstream of the sand dune will not increase the sand transport rate intensively, but change both wind velocity gradient and turbulence kinetic energy over surface of sand dune. On the other hand, when the bridge is built downstream the sand dune, simulation results show that sand deposition rate would be decreased in reference region downstream the pier.

Numerical study of impact erosion of multiple solid particle

Science.gov (United States)

Zheng, Chao; Liu, Yonghong; Chen, Cheng; Qin, Jie; Ji, Renjie; Cai, Baoping

2017-11-01

Material erosion caused by continuous particle impingement during hydraulic fracturing results in significant economic loss and increased production risks. The erosion process is complex and has not been clearly explained through physical experiments. To address this problem, a multiple particle model in a 3D configuration was proposed to investigate the dynamic erosion process. This approach can significantly reduce experiment costs. The numerical model considered material damping and elastic-plastic material behavior of target material. The effects of impact parameters on erosion characteristics, such as plastic deformation, contact time, and energy loss rate, were investigated. Based on comprehensive studies, the dynamic erosion mechanism and geometry evolution of eroded crater was obtained. These findings can provide a detailed erosion process of target material and insights into the material erosion caused by multiple particle impingement.

Using Cesium-137 technique to study the characteristics of different aspect of soil erosion in the Wind-water Erosion Crisscross Region on Loess Plateau of China

International Nuclear Information System (INIS)

Li Mian; Li Zhanbin; Liu Puling; Yao Wenyi

2005-01-01

The most serious soil erosion on Loess Plateau exists in the Wind-water Erosion Crisscross Region. In the past 20 years, the types and intensity of soil erosion and its temporal and spatial distribution were studied, but studies on the difference of soil erosion between slope aspects and slope positions in this area have no report. However, it is very important to analyze and evaluate quantitatively the characteristics of different aspects and positions of soil loss for the prevention and treatment of soil erosion in this area. The spatial pattern of net soil loss on 4 downslope transects in four aspects (east, west, south and north) on a typical Mao (round loess mound) in Liudaogou catchment in Wind-water Erosion Crisscross Region was measured in 2000 using the resident cesium-137 deficit technique. The purposes of this investigation were undertaken to determine whether or not 137 Cs measurement would give a useful indication of the extent of soil loss and their characteristics from cultivated hillsides in different slope aspect and slope position in the study area. The results showed that the difference of soil erosion in different aspect was significant and the erosion rate was in this order: north>east>south>west. Compared with other areas, the difference of erosion rate between north hillside and south hillside was on the contrary, and the possible explanations could be the effect of wind erosion. Also, the percentage of wind erosion was estimated to be at least larger than 18% of total soil loss by comparing the difference of erosion amount in south hillside and north hillside. The erosion rates on different slope positions in all aspects were also different, the highest net soil loss occurred in the lower slope position, and the upper and middle slope positions were slight. The general trend of net soil loss on sloping surface was to increase in fluctuation with increasing downslope distance

Using Cesium-137 technique to study the characteristics of different aspect of soil erosion in the Wind-water Erosion Crisscross Region on Loess Plateau of China

Energy Technology Data Exchange (ETDEWEB)

Li Mian E-mail: hnli-mian@163.com; Li Zhanbin; Liu Puling; Yao Wenyi

2005-01-01

The most serious soil erosion on Loess Plateau exists in the Wind-water Erosion Crisscross Region. In the past 20 years, the types and intensity of soil erosion and its temporal and spatial distribution were studied, but studies on the difference of soil erosion between slope aspects and slope positions in this area have no report. However, it is very important to analyze and evaluate quantitatively the characteristics of different aspects and positions of soil loss for the prevention and treatment of soil erosion in this area. The spatial pattern of net soil loss on 4 downslope transects in four aspects (east, west, south and north) on a typical Mao (round loess mound) in Liudaogou catchment in Wind-water Erosion Crisscross Region was measured in 2000 using the resident cesium-137 deficit technique. The purposes of this investigation were undertaken to determine whether or not {sup 137}Cs measurement would give a useful indication of the extent of soil loss and their characteristics from cultivated hillsides in different slope aspect and slope position in the study area. The results showed that the difference of soil erosion in different aspect was significant and the erosion rate was in this order: north>east>south>west. Compared with other areas, the difference of erosion rate between north hillside and south hillside was on the contrary, and the possible explanations could be the effect of wind erosion. Also, the percentage of wind erosion was estimated to be at least larger than 18% of total soil loss by comparing the difference of erosion amount in south hillside and north hillside. The erosion rates on different slope positions in all aspects were also different, the highest net soil loss occurred in the lower slope position, and the upper and middle slope positions were slight. The general trend of net soil loss on sloping surface was to increase in fluctuation with increasing downslope distance.

Erosion Modeling Analysis For Modified DWPF SME Tank

International Nuclear Information System (INIS)

LEE, SI

2004-01-01

In support of an erosion evaluation for the modified cooling coil guide and its supporting structure in the DWPF SME vessel, a computational model was developed to identify potential sites of high erosion using the same methodology established by previous work. The erosion mechanism identified in the previous work was applied to the evaluation of high erosion locations representative of the actual flow process in the modified coil guide of the SME vessel, abrasive erosion which occurs by high wall shear of viscous liquid. The results show that primary locations of the highest erosion due to the abrasive wall erosion are at the leading edge of the guide, external surface of the insert plate, the tank floor next to the insert plate of the coil guide support, and the upstream lead-in plate. The present modeling results show a good comparison between the original and the modified cases in terms of high erosion sites, as well as the degree of erosion and the calculated shear stress. Wall she ar of the tank floor is reduced by about 30 per cent because of the new coil support plate. Calculations for the impeller speed lower than 103 rpm in the SME showed similar erosion patterns but significantly reduced wall shear stresses and reduced overall erosion. Comparisons of the 103 rpm results with SME measurements indicated that no significant erosion of the tank floor in the SME is to be expected. Thus, it is recommended that the agitator speed of SME does not exceed 103 rpm

The delicate balance between soil production and erosion, and its role on landscape evolution

Energy Technology Data Exchange (ETDEWEB)

Dosseto, A., E-mail: tonyd@uow.edu.au [GeoQuEST Research Centre, School of Earth and Environmental Sciences, University of Wollongong. Wollongong, NSW (Australia); Buss, Heather [US Geological Survey. Menlo Park, CA (United States); Suresh, P.O. [Department of Environment and Geography, Macquarie University. North Ryde, NSW (Australia)

2011-06-15

Highlights: > The uranium-series isotope composition of regolith material can be used to determine the soil residence time. > Soil residence times up to 30 and 90 kyr are calculated for Frogs Hollow and Bisley, respectively. > Production rates are relatively similar for granitic and shale lithologies, but much higher over volcanic parent rock. > Soil production matches erosion in soil-mantled landscapes, demonstrating quantitatively that this type of landscape results from a balance between these two processes > Soil production is up to two orders of magnitude slower than erosion in cultivated areas. - Abstract: The diversity in landscapes at the Earth's surface is the result, amongst other things, of the balance (or imbalance) between soil production and erosion. While erosion rates are well constrained, it is only recently that we have been able to quantify rates of soil production. Uranium-series isotopes have been useful to provide such estimates independently of erosion rates. In this study, new U-series isotope are presented data from weathering profiles developed over andesitic parent rock in Puerto Rico, and granitic bedrock in southeastern Australia. The site in Australia is located on a highland plateau, neighbouring a retreating escarpment where soil production rates between 10 and 50 mm/kyr have been determined. The results show that production rates are invariant in these two regions of Australia with values between 15 and 25 mm/kyr for the new site. Andesitic soils show much faster rates, about 200 mm/kyr. Overall, soil production rates determined with U-series isotopes range between 10 and 200 mm/kyr. This is comparable to erosion rates in soil-mantled landscapes, but faster than erosion in cratonic areas and slower than in alpine regions and cultivated areas. This suggests that soil-mantled landscapes maintain soil because they can: there is a balance between production and erosion. Similarly, thick weathering profiles develop in cratonic areas

Long-term effects of grazing management and buffer strips on soil erosion from pastures

Science.gov (United States)

High grazing pressure can lead to soil erosion in pastures by compacting soil and increasing runoff and sediment delivery to waterways. Limited information exists on the effects of grazing management and best management practices (BMPs), such as buffer strips, on soil erosion from pastures. The obje...

Erosion and deposition in a field/forest system estimated using cesium-137 activity

International Nuclear Information System (INIS)

Lowrance, R.; McIntyre, S.; Lance, C.

1988-01-01

Soil erosion and deposition were estimated using Cs-137 activity within a 7.25-ha field/forest system in the southeastern coastal plain. Sol eroded from the field was deposited both in the riparian forest ecosystem and in downslope areas of the field. Total activity, depth to peak activity, and depth to zero activity increased downslope from field to stream. Erosion and deposition rates, estimated by changes in activity per unit area from a reference undisturbed forest site, showed that about twice as much total deposition had taken place as total erosion. Excess deposition was attributed to deposition from the upstream portions of the watershed. Erosion and deposition rates estimated with this method were about 63 and 256 Mg/ha/yr, respectively. Erosion and deposition rates estimated by two different calculation techniques were nearly identical. These rates were considerably higher than rates estimated in an earlier study. The rates may be overestimated because the differential rates of Cs-137 movement on clay particles were not considered. The riparian ecosystem acted as a very efficient sediment trap. 19 refs., 5 figs., 3 tabs

Soil erosion assessment - Mind the gap

Science.gov (United States)

Kim, Jongho; Ivanov, Valeriy Y.; Fatichi, Simone

2016-12-01

Accurate assessment of erosion rates remains an elusive problem because soil loss is strongly nonunique with respect to the main drivers. In addressing the mechanistic causes of erosion responses, we discriminate between macroscale effects of external factors - long studied and referred to as "geomorphic external variability", and microscale effects, introduced as "geomorphic internal variability." The latter source of erosion variations represents the knowledge gap, an overlooked but vital element of geomorphic response, significantly impacting the low predictability skill of deterministic models at field-catchment scales. This is corroborated with experiments using a comprehensive physical model that dynamically updates the soil mass and particle composition. As complete knowledge of microscale conditions for arbitrary location and time is infeasible, we propose that new predictive frameworks of soil erosion should embed stochastic components in deterministic assessments of external and internal types of geomorphic variability.

Use of 137Cs and other fallout radionuclide in soil erosion investigations: progress, problems and prospects

International Nuclear Information System (INIS)

Walling, D.E.

1998-01-01

Accelerated erosion and soil degradation currently represent serious problems for the global environment. Against this background there is a need to assemble reliable information on the rates of soil loss involved. Existing techniques for documenting rates of soil loss possess many limitations and there is increasing interest in the potential for using fallout radionuclides, particularly 137 Cs, to obtain such information. An example of the application of the 137 Cs approach to a cultivated field at Rufford Forest Farm, Nottinghamshire, UK, is presented to illustrate its value. The key advantages of the approach are that it provides a means of assembling retrospective estimates of medium-term (ca. 40 years) rates of soil loss and the spatial pattern of erosion and deposition involved, on the basis of a single site visit. There are, however, currently a number of problems and uncertainties associated with the use of 137 Cs in soil erosion investigations, and these are reviewed and needs for further research identified. Potential developments of the approach, including the use of other fallout radionuclides such as unsupported 210 Pb and 7 Be are also considered. (author)

Estimating soil erosion risk and evaluating erosion control measures for soil conservation planning at Koga watershed in the highlands of Ethiopia

Science.gov (United States)

Molla, Tegegne; Sisheber, Biniam

2017-01-01

Soil erosion is one of the major factors affecting sustainability of agricultural production in Ethiopia. The objective of this paper is to estimate soil erosion using the universal soil loss equation (RUSLE) model and to evaluate soil conservation practices in a data-scarce watershed region. For this purpose, soil data, rainfall, erosion control practices, satellite images and topographic maps were collected to determine the RUSLE factors. In addition, measurements of randomly selected soil and water conservation structures were done at three sub-watersheds (Asanat, Debreyakob and Rim). This study was conducted in Koga watershed at upper part of the Blue Nile basin which is affected by high soil erosion rates. The area is characterized by undulating topography caused by intensive agricultural practices with poor soil conservation practices. The soil loss rates were determined and conservation strategies have been evaluated under different slope classes and land uses. The results showed that the watershed is affected by high soil erosion rates (on average 42 t ha-1 yr-1), greater than the maximum tolerable soil loss (18 t ha-1 yr-1). The highest soil loss (456 t ha-1 yr-1) estimated from the upper watershed occurred on cultivated lands of steep slopes. As a result, soil erosion is mainly aggravated by land-use conflicts and topographic factors and the rugged topographic land forms of the area. The study also demonstrated that the contribution of existing soil conservation structures to erosion control is very small due to incorrect design and poor management. About 35 % out of the existing structures can reduce soil loss significantly since they were constructed correctly. Most of the existing structures were demolished due to the sediment overload, vulnerability to livestock damage and intense rainfall. Therefore, appropriate and standardized soil and water conservation measures for different erosion-prone land uses and land forms need to be implemented in Koga

Viewpoint: Sustainability of piñon-juniper ecosystems - A unifying perspective of soil erosion thresholds

Science.gov (United States)

Davenport, David W.; Breshears, D.D.; Wilcox, B.P.; Allen, Craig D.

1998-01-01

Many pinon-juniper ecosystem in the western U.S. are subject to accelerated erosion while others are undergoing little or no erosion. Controversy has developed over whether invading or encroaching pinon and juniper species are inherently harmful to rangeland ecosystems. We developed a conceptual model of soil erosion in pinon-jumper ecosystems that is consistent with both sides of the controversy and suggests that the diverse perspectives on this issue arise from threshold effects operating under very different site conditions. Soil erosion rate can be viewed as a function of (1) site erosion potential (SEP), determined by climate, geomorphology and soil erodibility; and (2) ground cover. Site erosion potential and cove act synergistically to determine soil erosion rates, as evident even from simple USLE predictions of erosion. In pinon-juniper ecosystem with high SEP, the erosion rate is highly sensitive to ground cover and can cross a threshold so that erosion increases dramatically in response to a small decrease in cover. The sensitivity of erosion rate to SEP and cover can be visualized as a cusp catastrophe surface on which changes may occur rapidly and irreversibly. The mechanisms associated with a rapid shift from low to high erosion rate can be illustrated using percolation theory to incorporate spatial, temporal, and scale-dependent patterns of water storage capacity on a hillslope. Percolation theory demonstrates how hillslope runoff can undergo a threshold response to a minor change in storage capacity. Our conceptual model suggests that pinion and juniper contribute to accelerated erosion only under a limited range of site conditions which, however, may exist over large areas.

Dependence of sputtering erosion on fuel-pellet characteristics

International Nuclear Information System (INIS)

Bohachevsky, I.O.; Hafer, J.F.

1977-11-01

Conceptual designs of fusion reactors operating on the principle of inertial confinement require that the dependence of cavity-wall erosion on fuel-pellet energy yield, its mass, and representative atomic number be known. A simple approximate model of sputtering erosion is presented and explicit formulas are derived that express the total amount of eroded wall material in terms of the above three parameters

Erosion-Oxidation Response of Boiler Grade Steels: A Mathematical Investigation

Directory of Open Access Journals (Sweden)

S. K. Das

2008-01-01

Full Text Available A ductile erosion model embodying the mechanisms of erosion involving cutting wear and repeated plastic deformation has been developed to predict erosion rates of boiler grade steels. The issue of erosion-oxidation interaction has also been addressed to further predict the mass loss resulted from this composite mechanism. A deterministic formalism for the kinetics of oxide-scale growth and a probabilistic approach to characterize the material loss are employed to describe simultaneous actions of high-temperature oxidation and mechanical erosion. The model predictions are in good agreement with the published data.

Human-induced C erosion and burial across spatial and temporal scales. (Invited)

Science.gov (United States)

van oost, K.

2013-12-01

Anthropogenic land cover change and soil erosion are tightly coupled: accelerated erosion and deposition of soil are inevitable consequences of the removal of vegetative cover and increased exposure of the soil surface to erosion. A significant portion of the earth surface has now been disturbed and this has locally accelerated erosion 10- to 100-fold. Although there is now growing awareness that the erosion-induced C flux may be an important factor determining global and regional net terrestrial ecosystem C balances, the significance of this disturbance for the past, present and future C cycle remains uncertain. In this paper, we argue that the significance for both past and present C budgets remains poorly quantified due to uncertainty about the contribution of biotic versus erosion-induced C fluxes because of their intrinsically different space and time scales. Carbon erosion research in agro-ecosystems has traditionally focused on short-term processes, i.e. single events to a few decades and longer-term observations of C and sediment dynamics are therefore rare. Likewise, C cycling is typically studied at the profile-scale while erosion processes operate over various spatial scales and whole-watershed approaches are therefore needed. We address this issue here by synthesizing 3 case studies where we report results of a measurement campaign to characterize the erosional control on vertical carbon fluxes from degraded land. First, using signatures in soil sedimentary archives, we integrate the effects of accelerated C erosion across point, hillslope and catchment scale for a temperate river catchment over the period of agriculture to demonstrate that accounting for the non-steady-state C dynamics in geomorphic active systems is pertinent to understand both past and future anthropogenic global change. Secondly, we report year-round soil respiration measurements with high temporal resolution along an erosion gradient on cultivated sloping land in the Chinese Loess

Erosion of a grooved surface caused by impact of particle-laden flow

Science.gov (United States)

Jung, Sohyun; Yang, Eunjin; Kim, Ho-Young

2016-11-01

Solid erosion can be a life-limiting process for mechanical elements in erosive environments, thus it is of practical importance in many industries such as construction, mining, and coal conversion. Erosion caused by particle-laden flow occurs through diverse mechanisms, such as cutting, plastic deformation, brittle fracture, fatigue and melting, depending on particle velocity, total particle mass and impingement angle. Among a variety of attempts to lessen erosion, here we investigate the effectiveness of millimeter-sized grooves on the surface. By experimentally measuring the erosion rates of smooth and triangular-grooved surfaces under various impingement angles, we find that erosion can be significantly reduced within a finite range of impingement angles. We show that such erosion resistance is attributed to the swirls of air within grooves and the differences in erosive strength of normal and slanted impact. In particular, erosion is mitigated when we increase the effective area under normal impact causing plastic deformation and fracture while decreasing the area under slanted impact that cuts the surface to a large degree. Our quantitative model for the erosion rate of grooved surfaces considering the foregoing effects agrees with the measurement results.

Influence of Intrinsic Factors on Erosive Tooth Wear in a Large-Scale Epidemiological Study.

Science.gov (United States)

Alaraudanjoki, Viivi; Laitala, Marja-Liisa; Tjäderhane, Leo; Pesonen, Paula; Lussi, Adrian; Ronkainen, Jukka; Anttonen, Vuokko

2016-01-01

To assess the influence of self-reported intrinsic factors [gastroesophageal reflux disease (GERD), long-term alcoholism, long-term heavy use of alcohol and multiple pregnancies] on erosive tooth wear in a middle-aged cohort sample. Of the total Northern Finland Birth Cohort (NFBC 1966), a convenience sample (n = 3,181) was invited for an oral health examination in 2012-2013, of which 1,962 participated, comprising the final study group. Erosive tooth wear was assessed by sextants using the Basic Erosive Wear Examination Index (BEWE, 0-18). Clinical data were supplemented by questionnaires conducted in 1997/1998 and 2012/2013. The participants were divided into severe (BEWE sum ≥9) and no-to-moderate (BEWE sum 0-8) erosive wear groups, and the logistic regression model was applied. Selected intrinsic factors were quite rare in this cohort sample and explained only 5.9% of the difference in the prevalence and severity of erosive wear. Daily symptoms of GERD [odds ratio (OR) 3.8, confidence interval (CI) 1.2-12.0] and hyposalivation (OR 3.8, CI 1.2-11.8) were the strongest risk indicators for severe erosive wear. Additionally, variables associated with an elevated risk for severe erosive wear were diagnosed alcoholism at any point (OR 2.5, CI 0.7-9.7) and self-reported heavy use of alcohol in both questionnaires (OR 2.0, CI 0.6-6.2). Even low-dose long-term consumption of alcohol was associated with erosive wear. In this cohort sample, intrinsic factors such as GERD or alcoholism alone are relatively uncommon causes of erosive tooth wear. The role of long-term use of alcohol in the erosion process may be bigger than presumed. © 2016 S. Karger AG, Basel.

Slurry erosion induced surface nanocrystallization of bulk metallic glass

Science.gov (United States)

Ji, Xiulin; Wu, Jili; Pi, Jinghong; Cheng, Jiangbo; Shan, Yiping; Zhang, Yingtao

2018-05-01

Microstructure evolution and phase transformation of metallic glasses (MGs) could occur under heating condition or mechanical deformation. The cross-section of as-cast Zr55Cu30Ni5Al10 MG rod was impacted by the solid particles when subjected to erosion in slurry flow. The surface microstructure was observed by XRD before and after slurry erosion. And the stress-driven de-vitrification increases with the increase of erosion time. A microstructure evolution layer with 1-2 μm thickness was formed on the topmost eroded surface. And a short range atomic ordering prevails in the microstructure evolution layer with crystalline size around 2-3 nm embedded in the amorphous matrix. The XPS analysis reveals that most of the metal elements in the MG surface, except for Cu, were oxidized. And a composite layer with ZrO2 and Al2O3 phases were formed in the topmost surface after slurry erosion. The cooling rate during solidification of MG has a strong influence on the slurry erosion induced nanocrystallization. And a lower cooling rate favors the surface nanocrystallization because of lower activation energy and thermo-stability. Finally, the slurry erosion induced surface nanocrystallization and microstructure evolution result in surface hardening and strengthening. Moreover, the microstructure evolution mechanisms were discussed and it is related to the cooling rate of solidification and the impact-induced temperature rise, as well as the combined effects of the impact-induced plastic flow, inter-diffusion and oxidation of the metal elements.

Comparison of Inconel 625 and Inconel 600 in resistance to cavitation erosion and jet impingement erosion

International Nuclear Information System (INIS)

Hu, H.X.; Zheng, Y.G.; Qin, C.P.

2010-01-01

Liquid droplet erosion (LDE), which often occurs in bellows made of nickel-based alloys, threatens the security operation of the nuclear power plant. As the candidate materials of the bellows, Inconel 600 and Inconel 625 were both tested for resistance to cavitation erosion (CE) and jet impingement erosion (JIE) through vibratory cavitation equipment and a jet apparatus for erosion-corrosion. Cumulative mass loss vs. exposure time was used to evaluate the erosion rate of the two alloys. The surface and cross-sectional morphologies before and after the erosion tests were observed by scanning electron microscopy (SEM), the inclusions were analyzed by an energy dispersive spectroscopy (EDS), and the surface roughness was also measured by surface roughness tester to illustrate the evolution of erosion process. The results show that the cumulative mass loss of CE of Inconel 625 is about 1/6 that of Inconel 600 and the CE incubation period of the Inconel 625 is 4 times as long as that of the Inconel 600. The micro-morphology evolution of CE process illustrates that the twinning and hardness of the Inconel 625 plays a significant role in CE. In addition, the cumulative mass loss of JIE of Inconel 625 is about 2/3 that of Inconel 600 at impacting angle of 90 o , and almost equal to that of the Inconel 600 at impacting angle of 30 o . Overall, the resistance to CE and JIE of Inconel 625 is much superior to that of Inconel 600.

The Erosion of Frozen Argon by Swift Helium Ions

DEFF Research Database (Denmark)

Besenbacher, F.; Bøttiger, Jørgen; Graversen, O.

1981-01-01

The temperature, energy, and thickness dependence of the erosion rates of frozen argon films when irradiated with 0.1–3 MeV helium ions have been measured. The erosion yields Y are much too high to be explained by the concentional collisional cascade-sputtering theory and are furthermore unequivo......The temperature, energy, and thickness dependence of the erosion rates of frozen argon films when irradiated with 0.1–3 MeV helium ions have been measured. The erosion yields Y are much too high to be explained by the concentional collisional cascade-sputtering theory and are furthermore...... unequivocally associated with electronic processes generated by the bombarding particle. In the present energy region, it is found that Y scales approximately as the electronic stopping power squared, depends on the charge state of the incoming helium ions, and perhaps more important, is independent...

The similarity of river evolution at the initial stage of channel erosion

Science.gov (United States)

Lin, Jiun-Chuan

2014-05-01

The study deals with a comparison study of two types of rocks at the initial stage of channel erosion in Taiwan. It is interesting that channel erosion at different types of rocks shows some similarity. There are two types of rocks: sandstone at Ta-an River, central Taiwan where river channel erosion from the nick point because of earthquake uplifting and mud rock at Tainan, southern Taiwan where rill erosion on a flat surface after artificial engineering. These two situations are both at the beginning stage of channel erosion, there are some similar landform appeared on channels. However the rate of erosion and magnitude of erosion are different. According to the using of photogrammetry method to reconstruct archive imageries and field surveying by total station and 3D scanner at different stages. The incision rate is high both at the Ta-an River and the bank erosion and it is even more obvious at mud rock area because of erodibility of mud rock. The results show that bank erosion and incision both are obvious processes. Bank erosion made channel into meander. The bank erosion cause slope in a asymmetric channel profile. The incision process will start at the site where land is relatively uplifted. This paper demonstrates such similarity and landform characters.

In-Situ Measurement of Hall Thruster Erosion Using a Fiber Optic Regression Probe

Science.gov (United States)

Polzin, Kurt; Korman, Valentin

2009-01-01

One potential life-limiting mechanism in a Hall thruster is the erosion of the ceramic material comprising the discharge channel. This is especially true for missions that require long thrusting periods and can be problematic for lifetime qualification, especially when attempting to qualify a thruster by analysis rather than a test lasting the full duration of the mission. In addition to lifetime, several analytical and numerical models include electrode erosion as a mechanism contributing to enhanced transport properties. However, there is still a great deal of dispute over the importance of erosion to transport in Hall thrusters. The capability to perform an in-situ measurement of discharge channel erosion is useful in addressing both the lifetime and transport concerns. An in-situ measurement would allow for real-time data regarding the erosion rates at different operating points, providing a quick method for empirically anchoring any analysis geared towards lifetime qualification. Erosion rate data over a thruster s operating envelope would also be useful in the modeling of the detailed physics inside the discharge chamber. There are many different sensors and techniques that have been employed to quantify discharge channel erosion in Hall thrusters. Snapshots of the wear pattern can be obtained at regular shutdown intervals using laser profilometry. Many non-intrusive techniques of varying complexity and sensitivity have been employed to detect the time-varying presence of erosion products in the thruster plume. These include the use quartz crystal microbalances, emission spectroscopy, laser induced flourescence, and cavity ring-down spectroscopy. While these techniques can provide a very accurate picture of the level of eroded material in the thruster plume, it is more difficult to use them to determine the location from which the material was eroded. Furthermore, none of the methods cited provide a true in-situ measure of erosion at the channel surface while

Application of a catchment evolution model to the prediction of long-term erosion on the spoil heap at Ranger uranium mine. Supervising Scientist report 132

International Nuclear Information System (INIS)

Willgoose, G.

1998-01-01

There is a need to assess the long-term stability of engineered landforms associated with the rehabilitation of Ranger Uranium Mine, Northern Territory, Australia, as it is a requirement that mill tailings must be contained for periods in excess of 1000 years. The geomorphic model, SIBERIA, is calibrated on hydrology and erosion data collected by a combination of monitoring and rainfall simulation experiments on the waste rock dumps of Ranger. Preliminary analysis of Ranger's preferred above-grade and below-grade rehabilitation options suggests that erosion of the order of 7-8 m will occur on the structure in a period of 1000 years. This depth of erosion may be sufficient to compromise the integrity of the containment. It is shown that SIBERIA has significant advantages over steady-state erosion models. Suggestions are made for the design that will enhance the stability of the structure and extend the structural life of the containment

Use of cesium-137 methodology in the evaluation of superficial erosive processes

International Nuclear Information System (INIS)

Andrello, Avacir Casanova; Appoloni, Carlos Roberto; Guimaraes, Maria de Fatima; Nascimento Filho, Virgilio Franco do

2003-01-01

Superficial erosion is one of the main soil degradation agents and erosion rates estimations for different edaphic climate conditions for the conventional models, as USLE and RUSLE, are expensive and time-consuming. The use of cesium- 137 anthropogenic radionuclide is a new methodology that has been much studied and its application in the erosion soil evaluation has grown in countries as USA, UK, Australia and others. A brief narration of this methodology is being presented, as the development of the equations utilized for the erosion rates quantification through the cesium- 137 measurements. Two watersheds studied in Brazil have shown that the cesium- 137 methodology was practicable and coherent with the survey in field for applications in erosion studies. (author)

State-of-the-art for evaluating the potential effects of erosion and deposition on a radioactive waste repository. Final report

International Nuclear Information System (INIS)

1980-01-01

The potential impact of future geologic processes on the integrity of a deep, high-level radioactive-waste repository is evaluated. The following study identifies the potential consequences of surface erosion and deposition on sub-surface repository containment characteristics and assesses the ability to measure and predict quantitatively the rates and corresponding extent of these processes in the long term. Numerous studies of the magnitudes and rates of surficial erosion and deposition that have been used to determine the minimum allowable depth for a geologic repository (300 m - NRC Code of Federal Regulations, Part 60.122, Draft 10) are cited in this report. Measurement and interpretation of potential rates and extent of surficial processes in these studies involved considerable uncertainty, and the implications of this uncertainty on presently proposed repository siting criteria are addressed herein. Important concepts that should be considered when developing siting criteria to protect against deleterious effects arising from future erosion or deposition are highlighted. Erosion agents that could affect deep repositories are distinguished in this report so that their individual and combined impacts may be examined. This approach is recommended when evaluating potential repository sites in diverse environments that are susceptible to different agents of erosion. In contrast, agents of sedimentation are not differentiated in this report because of their relatively minor impact on a deep repository

A method for modeling the effects of climate and land use changes on erosion and sustainability of soil in a Mediterranean watershed (Languedoc, France).

Science.gov (United States)

Paroissien, Jean-Baptiste; Darboux, Frédéric; Couturier, Alain; Devillers, Benoît; Mouillot, Florent; Raclot, Damien; Le Bissonnais, Yves

2015-03-01

Global climate and land use changes could strongly affect soil erosion and the capability of soils to sustain agriculture and in turn impact regional or global food security. The objective of our study was to develop a method to assess soil sustainability to erosion under changes in land use and climate. The method was applied in a typical mixed Mediterranean landscape in a wine-growing watershed (75 km(2)) within the Languedoc region (La Peyne, France) for two periods: a first period with the current climate and land use and a second period with the climate and land use scenarios at the end of the twenty-first century. The Intergovernmental Panel on Climate Change A1B future rainfall scenarios from the Météo France General circulation model was coupled with four contrasting land use change scenarios that were designed using a spatially-explicit land use change model. Mean annual erosion rate was estimated with an expert-based soil erosion model. Soil life expectancy was assessed using soil depth. Soil erosion rate and soil life expectancy were combined into a sustainability index. The median simulated soil erosion rate for the current period was 3.5 t/ha/year and the soil life expectancy was 273 years, showing a low sustainability of soils. For the future period with the same land use distribution, the median simulated soil erosion rate was 4.2 t/ha/year and the soil life expectancy was 249 years. The results show that soil erosion rate and soil life expectancy are more sensitive to changes in land use than to changes in precipitation. Among the scenarios tested, institution of a mandatory grass cover in vineyards seems to be an efficient means of significantly improving soil sustainability, both in terms of decreased soil erosion rates and increased soil life expectancies. Copyright © 2014 Elsevier Ltd. All rights reserved.

Dental Erosion and Dentinal Sensitivity amongst Professional Wine Tasters in South East Queensland, Australia

Directory of Open Access Journals (Sweden)

Roy George

2014-01-01

Full Text Available Background/Aims. Professional wine tasters face a hidden occupational hazard due to the high acid content in wine. This study evaluates the self-perceived dentinal sensitivity and erosive effects of wine on the professional wine tasters of the Granite Belt and the Scenic Rim regions of South East Queensland, Australia. Methods. Seventy wineries were contacted and participants were surveyed about their professional wine tasting experience and oral health. Participants were also required to rate their tooth sensitivity prior to being examined for erosion using a modified Smith & Knight tooth wear index. The data were analysed using Mann Whitney U test and Spearman’s correlation test. Results. The results showed that most participants (25 males, 22–66 yrs, brushed twice a day; however, the majority did not floss daily and had limited knowledge of the erosive effect of wine. There was a direct correlation between years of wine tasting, age of participants, and the erosion index. Correlation was not observed between the participant’s sensitivity index and erosion index. Conclusion. The lack of significant experience of dentinal hypersensitivity amongst professional wine tasters should not prevent oral health practitioners from providing necessary counselling and undertaking preventive measures, as tooth wear can have serious long-term effect on oral health of an individual.

Ways of TPP and NPP powerful steam turbine blade erosion decreasing in low flow rate regimes

International Nuclear Information System (INIS)

Khrabrov, P.V.; Khaimov, V.A.; Matveenko, V.A.

1986-01-01

A systematized approach to the problem of efficient cooling of flow passage and exhaust parts of TPP and NPP steam turbines and prevention of erosion wear of inlet and outlet edges of operating blades is presented. Methods for LP casing cooling and sources of erosion-hazard moisture as well as the main technological and design measures to decrease the erosion of blades are determined

Erosion of heat-treated AISI 4140 steel

Energy Technology Data Exchange (ETDEWEB)

Goretta, K.C. (Materials and Components Tech. Div., Argonne National Lab., IL (United States)); Thompson, A.C. (Materials and Components Tech. Div., Argonne National Lab., IL (United States)); Routbort, J.L. (Materials Science Div., Argonne National Lab., IL (United States))

1993-03-15

Solid-particle erosion was studied on AISI 4140 steel heat treated to have a Vickers hardness (Hv) of 288-650 kg mm[sup -2]. The experiments were conducted in vacuum with 143 [mu]m Al[sub 2]O[sub 3] abrasive impacting at 50-100 m s[sup -1] at an angle of 30 or 90 . Erosion rates were nearly independent of hardness for Hv[<=]365 kg mm[sup -2], but increased with hardness for Hv>365 kg mm[sup -2]. The improved erosion resistances of the softer alloys were attributed to increased ductilities. (orig.). Letter-to-the-editor

Regionalization of monthly rainfall erosivity patternsin Switzerland

Science.gov (United States)

Schmidt, Simon; Alewell, Christine; Panagos, Panos; Meusburger, Katrin

2016-10-01

One major controlling factor of water erosion is rainfall erosivity, which is quantified as the product of total storm energy and a maximum 30 min intensity (I30). Rainfall erosivity is often expressed as R-factor in soil erosion risk models like the Universal Soil Loss Equation (USLE) and its revised version (RUSLE). As rainfall erosivity is closely correlated with rainfall amount and intensity, the rainfall erosivity of Switzerland can be expected to have a regional characteristic and seasonal dynamic throughout the year. This intra-annual variability was mapped by a monthly modeling approach to assess simultaneously spatial and monthly patterns of rainfall erosivity. So far only national seasonal means and regional annual means exist for Switzerland. We used a network of 87 precipitation gauging stations with a 10 min temporal resolution to calculate long-term monthly mean R-factors. Stepwise generalized linear regression (GLM) and leave-one-out cross-validation (LOOCV) were used to select spatial covariates which explain the spatial and temporal patterns of the R-factor for each month across Switzerland. The monthly R-factor is mapped by summarizing the predicted R-factor of the regression equation and the corresponding residues of the regression, which are interpolated by ordinary kriging (regression-kriging). As spatial covariates, a variety of precipitation indicator data has been included such as snow depths, a combination product of hourly precipitation measurements and radar observations (CombiPrecip), daily Alpine precipitation (EURO4M-APGD), and monthly precipitation sums (RhiresM). Topographic parameters (elevation, slope) were also significant explanatory variables for single months. The comparison of the 12 monthly rainfall erosivity maps showed a distinct seasonality with the highest rainfall erosivity in summer (June, July, and August) influenced by intense rainfall events. Winter months have the lowest rainfall erosivity. A proportion of 62 % of

Minor soil erosion contribution to denudation in Central Nepal Himalaya.

Science.gov (United States)

Morin, Guillaume; France-Lanord, Christian; Gallo, Florian; Lupker, Maarten; Lavé, Jérôme; Gajurel, Ananta

2013-04-01

In order to decipher river sediments provenance in terms of erosion processes, we characterized geochemical compositions of hillslope material coming from soils, glaciers and landslide, and compared them to rivers sediments. We focused our study on two South flank Himalayan catchments: (1) Khudi khola, as an example of small High Himalayan catchment (150 km2), undergoing severe precipitation, and rapid erosion ≈ 3.5 mm/yr [A] and (2) the Narayani-Gandak Transhimalayan basin (52000 km2) that drains the whole central Nepal. To assess the question, systematic samplings were conducted on hillslope material from different erosion processes in the basins. River sediment include daily sampling during the 2010 monsoon at two stations, and banks samples in different parts of the basins. Source rocks, soil and landslide samples, are compared to river sediment mobile to immobile element ratios, completed by hydration degree H2O+ analysis[2]. Data show that soils are clearly depleted in mobile elements Na, K, Ca, and highly hydrated compared to source rocks and other erosion products. In the Khudi basin, the contrast between soil and river sediment signatures allow to estimate that soil erosion represents less than 5% of the total sediment exported by the river. Most of the river sediment therefore derives from landslides inputs and to a lesser extent by barren high elevation sub-basins. This is further consistent with direct observation that, during monsoon, significant tributaries of the Khudi river do not export sediments. Considering that active landslide zones represent less than 0.5% of the total watershed area, it implies that erosion distribution is highly heterogeneous. Landslide erosion rate could reach more than 50 cm/yr in the landslide area. Sediments of the Narayani river are not significantly different from those of the Khudi in spite of more diverse geomorphology and larger area of the basin. Only H2O+ and Total Organic Carbon concentrations normalised to Al

The Distribution and Magnitude of Glacial Erosion on 103-year Timescales at Engabreen, Norway

Science.gov (United States)

Rand, C.; Goehring, B. M.

2017-12-01

We derive the magnitudes of glacial erosion integrated over 103-year timescales across a transect transverse to the direction of ice flow at Engabreen, Norway. Understanding the distribution of glacial erosion is important for several reasons, including sediment budgeting to fjord environments, development of robust landscape evolution models, and if a better understanding between erosion and ice-bed interface properties (e.g., sliding rate, basal water pressure) can be developed, we can use records of glacial erosion to infer glaciological properties that can ultimately benefit models of past and future glaciers. With few exceptions, measurements of glacial erosion are limited to the historical past and even then are rare owing to the difficulty of accessing the glacier bed. One method proven useful in estimating glacial erosion on 103-year timescales is to measure the remaining concentrations of cosmogenic nuclides that accumulate in exposed bedrock during periods of retracted glacier extent and are removed by glacial erosion and radioactive decay during ice cover. Here we will present measurements of 14C and 10Be measured in proglacial bedrock from Engabreen. Our transects are ca. 600 and 400 meters in front of the modern ice front, and based on historical imagery, was ice covered until the recent past. Initial 10Be results show an increase in concentrations of nearly an order of magnitude from the samples near the center of the glacial trough to those on the lateral margin, consistent with conceptual models of glacial erosion parameterized in terms of sliding velocity. Naïve exposure ages that assume no subglacial erosion range from 0.22 - 9.04 ka. More importantly, we can estimate erosion depths by assuming zero erosion of the highest concentration sample along the two transects and calculate the amount of material removed to yield the lower concentrations elsewhere along the two transects. Results indicate minimum erosion depths of 1-183 cm for most ice

Comparative analysis of cell proliferation ratio in plaque and erosive oral lichen planus: An immunohistochemical study.

Science.gov (United States)

Redder, C Pramod; Pandit, Siddharth; Desai, Dinkar; Kandagal, V Suresh; Ingaleshwar, Pramod S; Shetty, Sharan J; Vibhute, Nupura

2014-05-01

Proliferating cell nuclear antigen (PCNA) is a nuclear protein synthesized in the late G1 and S-phase of the cell cycle. Detection of this protein represents a useful marker of the proliferation status of lesions. This study has been carried out to evaluate the cell proliferation rate in oral lichen planus (OLP) and comparison between plaque and erosive lichen planus, which indicates the potential for malignant transformation. This study was comprised of 64 cases of histologically proven lichen planus, out of which 32 cases of plaque and erosive each was taken. Two sections were taken from each, one for H and E staining to verify histological diagnosis according to Eisenberg criteria, other sections were stained according to super sensitive polymer horse radish peroxidise method for identifying immunohistochemical expression of PCNA. Data were statistically analyzed by Tukey high-range statistical domain test. Statistically significant P value was considered lichen planus, erosive type (66.86%) showed higher expression of PCNA followed by plaque (17.07%). Overall, P value was lichen planus followed by plaque type, which ultimately results in increased rate of malignant transformation. PCNA is a good nuclear protein marker to evaluate the proliferation status of OLP. Out of the two types of lichen planus, erosive type possesses more proliferative ratio and chances of malignant change is more in this type. It emphasizes the importance of long-term follow-up with erosive type when compared with plaque type.

Bentonite erosion. Final report

Energy Technology Data Exchange (ETDEWEB)

Birgersson, Martin; Boergesson, Lennart; Hedstroem, Magnus; Karnland, Ola; Nilsson, Ulf (Clay Technology AB, Lund (Sweden))

2009-12-15

Low saline water may reach KBS-3 repository depth, e.g. during periods of glaciation. Under such aqueous conditions, the montmorillonite part of the bentonite buffer might transform into a sol and thereby be transported away with flowing water in fractures. The primary aim with this report is to improve the understanding of the basic principles for this possible montmorillonite particle release. The report includes experimental and theoretical work performed at Clay Technology. Natural bentonite and ion-exchanged purified montmorillonite from three different geographical origins, Wyoming (U.S.), Milos (Greece) and Kutch (India) have been studied. Experimental and/or theoretical investigations have been performed with respect to: - Free swelling ability; - Rheological properties; - Rate of bentonite loss into fractures; - Filtering; - Ion exchange; - Sol formation ability; - Ion diffusion; - Mass loss due to erosion. The performed erosion experiments show that erosion does not occur in a mixed calcium/sodium montmorillonite with at least 20% calcium in exchange positions, when the external solution contains above 4 mM charge equivalents. This result is in agreement with the presented conceptual view of sol formation and measured equilibrium properties in mixed calcium/sodium montmorillonite. The findings imply that the buffer will be stable for non-glacial conditions. However, erosion due to sol formation cannot be ruled out for glacial conditions.

Bentonite erosion. Final report

International Nuclear Information System (INIS)

Birgersson, Martin; Boergesson, Lennart; Hedstroem, Magnus; Karnland, Ola; Nilsson, Ulf

2009-12-01

Low saline water may reach KBS-3 repository depth, e.g. during periods of glaciation. Under such aqueous conditions, the montmorillonite part of the bentonite buffer might transform into a sol and thereby be transported away with flowing water in fractures. The primary aim with this report is to improve the understanding of the basic principles for this possible montmorillonite particle release. The report includes experimental and theoretical work performed at Clay Technology. Natural bentonite and ion-exchanged purified montmorillonite from three different geographical origins, Wyoming (U.S.), Milos (Greece) and Kutch (India) have been studied. Experimental and/or theoretical investigations have been performed with respect to: - Free swelling ability; - Rheological properties; - Rate of bentonite loss into fractures; - Filtering; - Ion exchange; - Sol formation ability; - Ion diffusion; - Mass loss due to erosion. The performed erosion experiments show that erosion does not occur in a mixed calcium/sodium montmorillonite with at least 20% calcium in exchange positions, when the external solution contains above 4 mM charge equivalents. This result is in agreement with the presented conceptual view of sol formation and measured equilibrium properties in mixed calcium/sodium montmorillonite. The findings imply that the buffer will be stable for non-glacial conditions. However, erosion due to sol formation cannot be ruled out for glacial conditions.

A transient analysis of decomposition and erosion of concrete exposed to a surface heat flux

International Nuclear Information System (INIS)

Kilic, A.N.

1994-01-01

A simple approximation for predicting the concrete erosion rate and depth is derived based on the heat balance integral method for conduction with the time-dependent boundary conditions. The problem is considered a four-region model including separate, moving heat sinks at the boundaries due to endothermic decomposition reactions. Polynomial temperature profiles are assumed, and the results are compared with previous experimental data and other analytical solutions. Since the technique provides an approximate temperature distribution on the average, it does not give the real temperature evaluation but provides a simple prediction of the erosion rates and the depth of defaulted concrete in terms of the parameters that are important during the physical phenomena. Because of its simplicity and reliability, the model might be useful for the larger molten core/concrete interaction codes and aerosol generation models

Bank erosion of navigation canals in the western and central Gulf of Mexico

Science.gov (United States)

Thatcher, Cindy A.; Hartley, Stephen B.; Wilson, Scott A.

2011-01-01

Erosion of navigation canal banks is a direct cause of land loss, but there has been little quantitative analysis to determine why certain major canals exhibit faster widening rates (indicative of erosion) than others in the coastal zones of Texas, Louisiana, Mississippi, and Alabama. We hypothesize that navigation canals exhibit varying rates of erosion based on soil properties of the embankment substrate, vegetation type, geologic region (derived from digital versions of state geologic maps), and the presence or absence of canal bank armaments (that is, rock rip-rap, concrete bulkheads, or other shoreline protection structures). The first objective of this project was to map the shoreline position and substrate along both banks of the navigation canals, which were digitized from 3 different time periods of aerial photography spanning the years of 1978/79 to 2005/06. The second objective was to quantify the erosion rates of the navigation canals in the study area and to determine whether differences in erosion rates are related to embankment substrate, vegetation type, geologic region, or soil type. To measure changes in shoreline position over time, transects spaced at 50-m (164-ft) intervals were intersected with shorelines from all three time periods, and an annual rate of change was calculated for each transect. Mean annual rates of shoreline change ranged from 1.75 m/year (5.74 ft/year) on the west side of the Atchafalaya River, La., where there was shoreline advancement or canal narrowing, to -3.29 m/year (-10.79 ft/year) on the south side of the Theodore Ship Channel, Ala., where there was shoreline retreat or erosion. Statistical analysis indicated that there were significant differences in shoreline retreat rates according to geologic region and marsh vegetation type, and a weak relationship with soil organic content. This information can be used to better estimate future land loss rates associated with navigation canals and to prioritize the location of

Dental Erosion and Medical Conditions: An Overview of Aetiology, Diagnosis and Management.

Science.gov (United States)

Paryag, A; Rafeek, R

2014-09-01

Tooth wear or tooth surface loss is a normal physiological process and occurs throughout life but is considered pathological when the degree of destruction is excessive or the rate of loss is rapid, causing functional, aesthetic or sensitivity problems. The importance of tooth wear as a dental problem has been increasingly recognized. The findings of a study in Trinidad indicate that the prevalence of tooth wear in a Trinidadian population is comparable to the United Kingdom (UK) and, indeed, that the level of moderate and severe wear is in fact nearly twice as high. The aetiology of tooth wear is attributed to four causes: erosion, attrition, abrasion and abfraction. Erosion is generally considered to be the most prevalent cause of tooth wear in the UK and Europe. Acids that cause dental erosion originate mainly from the diet or the stomach and to a lesser extent, the environment. Underlying medical problems can contribute to the progress of tooth wear due to erosion and the patient may not be aware of these conditions. Moderate to severe tooth wear poses a significant clinical challenge to dental practitioners and may result in treatment that is more complex and costly to the patient both in terms of finances and time spent in the dental chair. This paper provides an overview of aetiology and diagnosis of tooth wear, in particular tooth wear due to erosion, so that medical and dental practitioners may recognize tooth wear early, institute preventive measures and manage patients appropriately.

Comparison of Inconel 625 and Inconel 600 in resistance to cavitation erosion and jet impingement erosion

Energy Technology Data Exchange (ETDEWEB)

Hu, H.X. [State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Science, 62 Wencui Road, Shenyang 110016 (China); Zheng, Y.G., E-mail: ygzheng@imr.ac.c [State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Science, 62 Wencui Road, Shenyang 110016 (China); Qin, C.P. [State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Science, 62 Wencui Road, Shenyang 110016 (China)

2010-10-15

Liquid droplet erosion (LDE), which often occurs in bellows made of nickel-based alloys, threatens the security operation of the nuclear power plant. As the candidate materials of the bellows, Inconel 600 and Inconel 625 were both tested for resistance to cavitation erosion (CE) and jet impingement erosion (JIE) through vibratory cavitation equipment and a jet apparatus for erosion-corrosion. Cumulative mass loss vs. exposure time was used to evaluate the erosion rate of the two alloys. The surface and cross-sectional morphologies before and after the erosion tests were observed by scanning electron microscopy (SEM), the inclusions were analyzed by an energy dispersive spectroscopy (EDS), and the surface roughness was also measured by surface roughness tester to illustrate the evolution of erosion process. The results show that the cumulative mass loss of CE of Inconel 625 is about 1/6 that of Inconel 600 and the CE incubation period of the Inconel 625 is 4 times as long as that of the Inconel 600. The micro-morphology evolution of CE process illustrates that the twinning and hardness of the Inconel 625 plays a significant role in CE. In addition, the cumulative mass loss of JIE of Inconel 625 is about 2/3 that of Inconel 600 at impacting angle of 90{sup o}, and almost equal to that of the Inconel 600 at impacting angle of 30{sup o}. Overall, the resistance to CE and JIE of Inconel 625 is much superior to that of Inconel 600.

Experiment of cavitation erosion at the exit of a long orifice

Energy Technology Data Exchange (ETDEWEB)

Yagi, Yoshinori; Murase, Michio [Inst. of Nuclear Safety System Inc., Mihama, Fukui (Japan)

2002-09-01

We performed experiments to clarify mechanism of cavitation erosion and to predict cavitation erosion rate at the exit of a long orifice equipped at the chemical and volume control system in a pressurized water reactor (PWR). In order to find this mechanism, we used a high speed video camera. As the result, we observed bubble collapses near the exit of the orifice when flow condition was oscillating. So the bubble collapses due to the oscillation might cause the first stage erosion at the exit of the orifice. Using the orifice which had the cone-shaped exit, we observed that bubbles collapsed near the exit and then they collapsed at the upstream like a chain reaction. So this bubble collapse mechanism could be explained as follows: shock wave was generated by the bubble collapse near the exit, then it propagated upwards, consequently it caused the bubble collapse at the upstream. And we predicted erosion rate by evaluating the effect of the velocity and comparing the erosion resistance between the test speciment (aluminum) and the plant material (stainless steel) by means of vibratory tests. We compared the predicted erosion rate with that of the average value estimated from plant investigation, then we examined the applicability of these method to the plant evaluations. (author)

Constraints on the affinity term for modeling long-term glass dissolution rates

International Nuclear Information System (INIS)

Bourcier, W.L.; Carroll, S.A.; Phillips, B.L.

1993-11-01

Predictions of long-term glass dissolution rates are highly dependent on the form of the affinity term in the rate expression. Analysis of the quantitative effect of saturation state on glass dissolution rate for CSG glass (a simple analog of SRL-165 glass), shows that a simple (1-Q/K) affinity term does not match experimental results. Our data at 100 degree C show that the data is better fit by an affinity term having the form (1 - (Q/K) 1 /σ) where σ = 10

Advances in modeling soil erosion after disturbance on rangelands

Science.gov (United States)

Research has been undertaken to develop process based models that predict soil erosion rate after disturbance on rangelands. In these models soil detachment is predicted as a combination of multiple erosion processes, rain splash and thin sheet flow (splash and sheet) detachment and concentrated flo...

Projected climate change impacts in rainfall erosivity over Brazil

Science.gov (United States)

Climate change projections and historical analyses have shown alterations in global precipitation dynamics, and therefore, it is also expected that there will be associated changes to soil erosion rates. The impacts of climate change on soil erosion may bring serious economic, social, and environmen...

Density Development During Erosion Experiments of Cohesive Sediments

DEFF Research Database (Denmark)

Johansen, Claus; Larsen, Torben

1998-01-01

The density development during erosion experiments was investigated. The calculation of the erosion rate requires the knowledge of the density profile with respect to the consolidation time(Parchure, 1984). At present, the basic assumption in the calculations is that the density profile is achiev...... in order to obtail time invariant sediment properties during the experiments....

Comparison Between Bandage Contact Lenses and Pressure Patching on the Erosion Area and Pain Scale in Patients With Corneal Erosion.

Science.gov (United States)

Triharpini, Ni Nyoman; Gede Jayanegara, I Wayan; Handayani, Ariesanti Tri; Widiana, I Gde Raka

2015-01-01

Corneal erosion is common in eye emergency cases. Extensive corneal erosions result in severe pain and prolonged healing time. This study aimed to compare bandage contact lenses with pressure patching in terms of reducing the size of the erosion area, pain scale in patients with corneal erosion and its complications. A randomized open-label clinical trial was conducted. Subjects with mechanical corneal erosion were selected to use either bandage contact lenses or pressure patching. All subjects received antibiotic eye drops and 0.5% tropicamide eye drops. Evaluations were done 24 and 72 hours after treatment. The size of the corneal erosion area, pain scale, and complications were assessed. A total of 32 eyes (16 eyes in each group) were studied. The change in the size of the corneal erosion area was greater in the bandage contact lens group than in the pressure patching group, although there was no significant difference. In the bandage contact lens group, 56.25% of the eyes were healed at 24 hours and 43.75% were healed at 72 hours. In the pressure patching group, 62.50% were healed at 24 hours and 12.50% were healed at 72 hours. The change in pain scale was significantly greater in the bandage contact lens group than in the pressure patching group. No complications were found in both groups. Bandage contact lenses are an effective alternative to treating mechanical corneal erosion because of their effect in reducing pain without causing any complications.

Numerical modelling of concentrated leak erosion during Hole Erosion Tests

OpenAIRE

Mercier, F.; Bonelli, S.; Golay, F.; Anselmet, F.; Philippe, P.; Borghi, R.

2015-01-01

This study focuses on the numerical modelling of concentrated leak erosion of a cohesive soil by a turbulent flow in axisymmetrical geometry, with application to the Hole Erosion Test (HET). The numerical model is based on adaptive remeshing of the water/soil interface to ensure accurate description of the mechanical phenomena occurring near the soil/water interface. The erosion law governing the interface motion is based on two erosion parameters: the critical shear stress and the erosion co...

Parameters Affecting the Erosive Burning of Solid Rocket Motor

OpenAIRE

Abdelaziz Almostafa; Guozhu Liang; Elsayed Anwer

2018-01-01

Increasing the velocity of gases inside solid rocket motors with low port-to-throat area ratios, leading to increased occurrence and severity of burning rate augmentation due to flow of propellant products across burning propellant surfaces (erosive burning), erosive burning of high energy composite propellant was investigated to supply rocket motor design criteria and to supplement knowledge of combustion phenomena, pressure, burning rate and high velocity of gases all of these are parameter...

Soil water erosion on Mediterranean vineyards. A review based on published data

Science.gov (United States)

Prosdocimi, Massimo; Cerdà, Artemi; Tarolli, Paolo

2015-04-01

Soil water erosion on cultivated lands is a severe threat to soil resources in the world (Leh et al., 2013; Zhao et al., 2013). In particular, Mediterranean areas deserve a particular attention because of their edaphic, topographic and climatic conditions. Among the cultivated lands, concerns have arisen about vineyards because, aside representing one of the most important crop in terms of income and employment, they also have proven to be the form of agricultural land that causes one of the highest soil losses (Tropeano et al., 1984; Leonard and Andrieux, 1998; Ferrero et al., 2005; Cerdà et al., 2007; Blavet et al., 2009; Casalí et al., 2009; Novara et al., 2011; Martínez Casasnovas et al., 2013; Ruiz Colmenero et al., 2013; Tarolli et al., 2014). Although the topic of soil water erosion on vineyards has been studied, it still raises uncertainties. These are due to the i) high complexity of processes involved, ii) different methodologies used to analyze them and iii) analyses carried out at different spatial and temporal scales. At this regard, this work aims to evaluate the impact of factors controlling erosion such as rainfall characteristics, topography, soil properties and soil and water conservation techniques. Data derived from experimental plots have been reviewed. At first, what emerges is the difficulty of comparing erosion rates obtained with different methodologies and at different spatial scales. Secondly, all the factors demonstrate to have a strong impact on soil erosion but a 'general rule' upon which to consider one factor always predominant over the others does not come out. Therefore, this work supports the importance of monitoring soil water erosion by field measurements to better understand the relationship between the factors. Variables like rainfall characteristics, topography and soil properties are much more difficult to modify than the soil and water management techniques. Hence, future researches are needed to both recommend the best

Comparative analysis of cell proliferation ratio in plaque and erosive oral lichen planus: An immunohistochemical study

Directory of Open Access Journals (Sweden)

C Pramod Redder

2014-01-01

Full Text Available Background: Proliferating cell nuclear antigen (PCNA is a nuclear protein synthesized in the late G1 and S-phase of the cell cycle. Detection of this protein represents a useful marker of the proliferation status of lesions. This study has been carried out to evaluate the cell proliferation rate in oral lichen planus (OLP and comparison between plaque and erosive lichen planus, which indicates the potential for malignant transformation. Materials and Methods: This study was comprised of 64 cases of histologically proven lichen planus, out of which 32 cases of plaque and erosive each was taken. Two sections were taken from each, one for H and E staining to verify histological diagnosis according to Eisenberg criteria, other sections were stained according to super sensitive polymer horse radish peroxidise method for identifying immunohistochemical expression of PCNA. Data were statistically analyzed by Tukey high-range statistical domain test. Statistically significant P value was considered <0.05. Results: In two types of lichen planus, erosive type (66.86% showed higher expression of PCNA followed by plaque (17.07%. Overall, P value was <0.001, which was statistically significant. It indicates that proliferation activity is more in erosive lichen planus followed by plaque type, which ultimately results in increased rate of malignant transformation. Conclusion: PCNA is a good nuclear protein marker to evaluate the proliferation status of OLP. Out of the two types of lichen planus, erosive type possesses more proliferative ratio and chances of malignant change is more in this type. It emphasizes the importance of long-term follow-up with erosive type when compared with plaque type.

Rehabilitation at Nabarlek: erosion assessment 1999

International Nuclear Information System (INIS)

Evans, K.G.; Saynor, M.J.; Hancock, G.R.

2001-01-01

Decommissioning work and the rehabilitation at the Nabarlek minesite were completed at the end of 1995. Site description, mining history, environmental management and rehabilitation have been summarised elsewhere (Prendergast et al 1999, Martin 2000, Waggitt 2001). Tailings were buried in the mined-out pit and capped with waste rock. An erosion assessment of the cap design, using a combination of modelling and analogue estimates, indicated that denudation rates on the cap would be -1 (Riley 1995). Riley (1995) suggested minor design modifications to reduce slope length on the pit cap to improve stability and provide structural integrity for several thousand years. Riley (1995) observed that roads were areas of most severe rill development in the Alligator Rivers Region (ARR) and suggested that rill development (0.2-0.3 m depth) on the pit cap would occur in the early stages of adjustment toward equilibrium but not persist in the long term. Consequently, as part of the process of assessing rehabilitation success, erosion at the former minesite was examined by ERISS in August and October 1999. A ground assessment of the perimeter of the evaporation ponds, pit and waste rock dump (WRD), unsealed roads to the north and east of the site and infrastructure area was conducted in August 1999. This survey described, quantified (using a tape and rule) and photographed erosion features. No transects were undertaken. In October 1999, a qualitative (descriptive and photographic) survey of the airstrip, constructed drains, unsealed roads to the west of the site, the pit and WRD was conducted. On this occasion, transects of the WRD and pit were taken but the locations of the transects were not surveyed

Active tectonics and Holocene versus modern catchment erosion rates at 300 MW Baspa II hydroelectric power plant (NW Himalaya, India)

Science.gov (United States)

Draganits, Erich; Grasemann, Bernhard; Gier, Susanne; Hofmann, Christa-Charlotte; Janda, Christoph; Bookhagen, Bodo; Preh, Alexander

2015-04-01

The Baspa River is one of the most important tributaries to the Sutlej River in the NW Himalaya (India). Its catchment is 1116 km2 in size, ranges from c. 6400 m asl to 1770 m asl and contains India's largest private hydroelectric facility, the 300 MW Baspa II. Geologically, the hydroelectric installation is located in the Higher Himalayan Crystalline, just above the active Karcham Normal Fault, which is reactivating the Early Miocene Main Central Thrust, one of the principal Himalayan faults. The area is seismically active and mass-movements are common. Around 8200 yrs BP the Baspa was dammed by a rock-avalanche dam, leading to the formation of the originally c. 260 m deep palaeo-lake Sangla palaeo-lake. Detailed sedimentological investigations and radiocarbon dating indicate that the palaeo-lake was completely filled with sediments until c. 5100 yrs BP. This makes the Sangla palaeo-lake to a very rare example of a mass-movement dam with very long duration and its lacustrine sediments represent a valuable archive for geological processes and environmental proxies within the Baspa catchment during the c. 3100 years of its existence - which are the aim of our study. At least 5 levels of soft-sediment deformation have been recorded in the exposed part of the lacustrine sediments of Sangla palaeo-lake, including brecciated laminae, overturned laminae, folds, faults and deformation bands, separated by undeformed deposits. They are interpreted as seismites, indicating at least 5 earthquakes within 2500 years strong enough to cause liquefaction. The 300 MW Baspa II hydro-electric power plant has been built exactly on top of this palaeo-lake. This special location represents a very rare possibility to evaluate the short-term, river load and hydrological parameters measured during the planning and operational stages of Baspa II with the long-term parameters gained from the palaeo-lake sediments from the catchment. This data show that the Mid-Holocene erosion rates of the

Combining Landsat TM multispectral satellite imagery and different modelling approaches for mapping post-fire erosion changes in a Mediterranean site

Science.gov (United States)

Petropoulos, George P.; Kairis, Orestis; Karamesouti, Mina; Papanikolaou, Ioannis D.; Kosmas, Constantinos

2013-04-01

South European countries are naturally vulnerable to wildfires. Their natural resources such as soil, vegetation and water may be severely affected by wildfires, causing an imminent environmental deterioration due to the complex interdependence among biophysical components. Soil surface water erosion is a natural process essential for soil formation that is affected by such interdependences. Accelerated erosion due to wildfires, constitutes a major restrictive factor for ecosystem sustainability. In 2007, South European countries were severely affected by wildfires, with more than 500,000 hectares of land burnt in that year alone, well above the average of the last 30 years. The present work examines the changes in spatial variability of soil erosion rates as a result of a wildfire event that took place in Greece in 2007, one of the most devastating years in terms of wildfire hazards. Regional estimates of soil erosion rates before and after the fire outbreak were derived from the Revised Universal Soil Loss Equation (RUSLE, Renard et al. 1991) and the Pan-European Soil Erosion Risk Assessment model (PESERA, Kirkby, 1999; Kirkby et al., 2000). Inputs for both models included climatic, land-use, soil type, topography and land use management data. Where appropriate, both models were also fed with input data derived from the analysis of LANDSAT TM satellite imagery available in our study area, acquired before and shortly after the fire suppression. Our study was compiled and performed in a GIS environment. In overall, the loss of vegetation from the fire outbreak caused a substantial increase of soil erosion rates in the affected area, particularly towards the steep slopes. Both tested models were compared to each other and noticeable differences were observed in the soil erosion predictions before and after the fire event. These are attributed to the different parameterization requirements of the 2 models. This quantification of sediment supply through the river

Floodplain trapping and cycling compared to streambank erosion of sediment and nutrients in an agricultural watershed

Science.gov (United States)

Gillespie, Jaimie; Noe, Gregory; Hupp, Cliff R.; Gellis, Allen; Schenk, Edward R.

2018-01-01

Floodplains and streambanks can positively and negatively influence downstream water quality through interacting geomorphic and biogeochemical processes. Few studies have measured those processes in agricultural watersheds. We measured inputs (floodplain sedimentation and dissolved inorganic loading), cycling (floodplain soil nitrogen [N] and phosphorus [P] mineralization), and losses (bank erosion) of sediment, N, and P longitudinally in stream reaches of Smith Creek, an agricultural watershed in the Valley and Ridge physiographic province. All study reaches were net depositional (floodplain deposition > bank erosion), had high N and P sedimentation and loading rates to the floodplain, high soil concentrations of N and P, and high rates of floodplain soil N and P mineralization. High sediment, N, and P inputs to floodplains are attributed to agricultural activity in the region. Rates of P mineralization were much greater than those measured in other studies of nontidal floodplains that used the same method. Floodplain connectivity and sediment deposition decreased longitudinally, contrary to patterns in most watersheds. The net trapping function of Smith Creek floodplains indicates a benefit to water quality. Further research is needed to determine if future decreases in floodplain deposition, continued bank erosion, and the potential for nitrate leaching from nutrient-enriched floodplain soils could pose a long-term source of sediment and nutrients to downstream rivers.

Impacts of shoreline erosion on coastal ecosystems in Songkhla Province

Directory of Open Access Journals (Sweden)

Nipaporn Chusrinuan

2009-07-01

Full Text Available Songkhla Province is located on the eastern coast of the southern Thai Peninsula, bordering the Gulf of Thailand for approximately 107 km. Most of the basin’s foreshores have been extensively developed for housing, tourism and shrimp farming. The beaches are under deteriorating impacts, often causing sediment transport which leads to an unnaturally high erosion rate. This natural phenomenon is considered to be a critical problem in the coastal areas affected by the hazard of coastal infrastructure and reduced beach esthetics for recreation. In this study, shoreline changes were compared between 1975 and 2006 using aerial photographs and Landsat imageries using Geographic Information System (GIS. The results revealed that 18.5 km2 of the coastal areas were altered during the period. Of this, 17.3 km2 suffered erosion and 1.2 km2were subjected to accretion. The most significant changes occurred between 1975-2006. Shoreline erosion was found at Ban Paktrae, Ranot District, with an average erosion rate of 5.3 m/year, while accretion occurred at Laem Samila, MuangSongkhla District with an average accretion rate of 2.04 m/year. The occurrences of shoreline erosion have contributed to the degradation of coastal soil and water quality, destruction of beach and mangrove forests, loss of human settlements and livelihood.These processes have led to deterioration of the quality of life of the residents. Prevention and mitigation measures to lessen economic and social impacts due to shoreline erosion are discussed.

Progress of nuclide tracing technique in the study of soil erosion in recent decade

International Nuclear Information System (INIS)

Liu Gang; Yang Mingyi; Liu Puling; Tian Junliang

2007-01-01

In the last decade nuclide tracing technique has been widely employed in the investigation of soil erosion, which makes the studies of soil erosion into a new and rapid development period. This paper tried to review the recent progress of using 137 Cs, 210 Pb ex , 7 Be, composite tracers and REE-INAA in soil erosion rate, sedimentation rate, sediment source and soil erosion processes study, and also the existing research results. The trends for future development and questions are also discussed. (authors)

Formulating Fine to Medium Sand Erosion for Suspended Sediment Transport Models

Directory of Open Access Journals (Sweden)

François Dufois

2015-08-01

Full Text Available The capacity of an advection/diffusion model to predict sand transport under varying wave and current conditions is evaluated. The horizontal sand transport rate is computed by vertical integration of the suspended sediment flux. A correction procedure for the near-bed concentration is proposed so that model results are independent of the vertical resolution. The method can thus be implemented in regional models with operational applications. Simulating equilibrium sand transport rates, when erosion and deposition are balanced, requires a new empirical erosion law that involves the non-dimensional excess shear stress and a parameter that depends on the size of the sand grain. Comparison with several datasets and sediment transport formulae demonstrated the model’s capacity to simulate sand transport rates for a large range of current and wave conditions and sand diameters in the range 100–500 μm. Measured transport rates were predicted within a factor two in 67% of cases with current only and in 35% of cases with both waves and current. In comparison with the results obtained by Camenen and Larroudé (2003, who provided the same indicators for several practical transport rate formulations (whose means are respectively 72% and 37%, the proposed approach gives reasonable results. Before fitting a new erosion law to our model, classical erosion rate formulations were tested but led to poor comparisons with expected sediment transport rates. We suggest that classical erosion laws should be used with care in advection/diffusion models similar to ours, and that at least a full validation procedure for transport rates involving a range of sand diameters and hydrodynamic conditions should be carried out.

Simultaneous acid exposure and erosive particle wear of thermoset coatings

DEFF Research Database (Denmark)

Møller, Victor Buhl; Dam-Johansen, Kim; Frankær, Sarah Maria

2018-01-01

, similar to the erosion/corrosion-type phenomena found in metals. A vinyl ester-based coating was the most resistant to the simultaneous erosive/acidic exposure, with a maximum polishing rate of 3.24±0.61 μm/week, while novolac epoxy and polyurethane coatings showed high polishing rates of 11.7±1.50 and 13.4±0......Handling acidic chemicals is a challenge in the chemical industry, requiring a careful choice of contact material. Certain thermoset organic coatings are applicable in low pH environments, but when particulate erosion is also present the performance demand is increased. This is the case in, e...