WorldWideScience

Sample records for terbium borides

  1. Analysis of aluminum boride and zirconium boride

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, Yasuo (Institute of Physical and Chemical Research, Wako, Saitama (Japan))

    1982-09-01

    A method for analyzing aluminum and zirconium borides is presented. Decomposition of the borides was achieved in a Uniseal Decomposition Vessel (capacity, 23 ml), in which aluminum boride was heated with (1 + 1) HNO/sub 3/ at 150/sup 0/C for 3 h and zirconium boride with a mixture of (1 + 1) HNO/sub 3/ and (1 + 5) H/sub 2/SO/sub 4/ at the same temperature for 6 h. Aluminum and boron in the solution obtained were separated with cation exchange resin (Dowex 50 WX 8). Boron in the effluent was determined with the titrimetric method using mannite. Aluminum adsorped on the resin was eluted with 2 M HCl and determined by chelatometric titration. Zirconium was separated from boron as zirconium hydroxide by precipitation with NaOH and by filtration with a Nucleopore membrane filter. Boron in the filtrate was determined by the above mentioned method. After dissolution of zirconium hydroxide with HCl, zirconium was precipitated with mandelic acid. The optimum concentration of HCl for the complete precipitation of zirconium mandelate was (2 -- 3) M. The precipitate was filtered on a G 4 glass filter, dried at 110/sup 0/C and weighted as zirconium tetramandelate. The following boride samples were analyzed: Selected crystals of ..cap alpha..-AlB/sub 12/ and ..beta..-AlB/sub 12/, and two ZrB/sub 2/ samples, the one prepared by carbothermic reduction and the other by direct reaction of zirconium and boron.

  2. Kinetics of borided gear steels

    Indian Academy of Sciences (India)

    The boride layer was characterized by optical microscopy, X-ray diffraction technique and microVickers hardness tester. X-ray diffraction analysis of boride layers on the surface of the steels revealed the existence of FeB, Fe2B, CrB and Cr2B compounds. The thickness of the boride layer increases by increasing boriding ...

  3. Kinetics of borided gear steels

    Indian Academy of Sciences (India)

    source used, boriding temperature, treatment time, and properties of the borided material (Sahin. & Meric 2002 ... The boriding heat treatment was carried out in solid medium containing an Ekabor-II ..... 2007 Growth kinetics of boride layers on iron-chromium alloys and their dry abrasive wear resistance,. Materials Science ...

  4. Elastic properties of terbium

    DEFF Research Database (Denmark)

    Spichkin, Y.I.; Bohr, Jakob; Tishin, A.M.

    1996-01-01

    The temperature dependence of the Young modulus along the crystallographic axes b and c (E(b) and E(c)), and the internal friction of a terbium single crystal have been measured. At 4.2 K, E(b) and E(c) are equal to 38 and 84.5 GPa, respectively. The lattice part of the Young modulus and the Debye...... temperature has been calculated. The origin of the Young modulus anomalies arising at the transition to the magnetically ordered state is discussed....

  5. An investigation on borided AISI 1020 steel

    Science.gov (United States)

    Altinsoy, I.; Efe, F. G. Celebi; Ipek, M.; Ozbek, I.; Zeytin, S.; Bindal, C.

    2013-12-01

    In this study, we investigated some properties of borided AISI 1020 steel. Boronizing heat treatment was carried out at 800°C, 875°C and 950°C for 2, 4, 6 and 8 h using Ekabor 1 powders. The hardness of borides formed on the steel substrate measured via Vickers indenter was about 1500 HVN. The thickness of boride layers depending on the process temperature and time was ranged from 20.5 to 216 μm. The presence of Fe2B boride was determined by XRD analysis. SEM microscope studies showed that the borides formed on the AISI 1020 steel have columnar nature. Kinetics studies reveal a parabolic relationship between layer depth and process time, and the activation energy is calculated as 164,356 kJ/mol. Moreover, an attempt was made to investigate the possibility of predicting the iso-thickness of boride layer and to establish an empirical relationship between process parameters of boriding and boride layer for industrial applications.

  6. Characterization of AISI 4140 borided steels

    Energy Technology Data Exchange (ETDEWEB)

    Campos-Silva, I., E-mail: icampos@ipn.mx [Instituto Politecnico Nacional, Grupo Ingenieria de Superficies, SEPI-ESIME U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F., 07738 (Mexico); Ortiz-Dominguez, M.; Lopez-Perrusquia, N.; Meneses-Amador, A. [Instituto Politecnico Nacional, Grupo Ingenieria de Superficies, SEPI-ESIME U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F., 07738 (Mexico); Escobar-Galindo, R. [Instituto de Ciencia de Materiales de Madrid (CSIC), E-28049 Cantoblanco, Madrid (Spain); Martinez-Trinidad, J. [Instituto Politecnico Nacional, Grupo Ingenieria de Superficies, SEPI-ESIME U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F., 07738 (Mexico)

    2010-02-01

    The present study characterizes the surface of AISI 4140 steels exposed to the paste-boriding process. The formation of Fe{sub 2}B hard coatings was obtained in the temperature range 1123-1273 K with different exposure times, using a 4 mm thick layer of boron carbide paste over the material surface. First, the growth kinetics of boride layers at the surface of AISI 4140 steels was evaluated. Second, the presence and distribution of alloying elements on the Fe{sub 2}B phase was measured using the Glow Discharge Optical Emission Spectrometry (GDOES) technique. Further, thermal residual stresses produced on the borided phase were evaluated by X-ray diffraction (XRD) analysis. The fracture toughness of the iron boride layer of the AISI 4140 borided steels was estimated using a Vickers microindentation induced-fracture testing at a constant distance of 25 {mu}m from the surface. The force criterion of fracture toughness was determined from the extent of brittle cracks, both parallel and perpendicular to the surface, originating at the tips of an indenter impression. The fracture toughness values obtained by the Palmqvist crack model are expressed in the form K{sub C}({pi}/2) > K{sub C} > K{sub C}(0) for the different applied loads and experimental parameters of the boriding process.

  7. The electrochemical synthesis of europium boride

    Directory of Open Access Journals (Sweden)

    Bukatova G.A.

    2003-01-01

    Full Text Available The electroreduction of boron, europium and the electrochemical synthesis of europium boride have been investigated in NaCl-KCl-NaF(10 wt. % melt on silver and molybdenum electrodes. The parameters of boron reduction in the chloride-fluoride melt have been obtained and the character of its joint deposition with europium has been studied.

  8. The electrochemical synthesis of europium boride

    OpenAIRE

    Bukatova G.A.; Kuznetsov S.A.; Gaune-Escard M.

    2003-01-01

    The electroreduction of boron, europium and the electrochemical synthesis of europium boride have been investigated in NaCl-KCl-NaF(10 wt. %) melt on silver and molybdenum electrodes. The parameters of boron reduction in the chloride-fluoride melt have been obtained and the character of its joint deposition with europium has been studied.

  9. Characterization of rough interfaces obtained by boriding

    Energy Technology Data Exchange (ETDEWEB)

    Campos-Silva, I. [Instituto Politecnico Nacional, SEPI-ESIME, U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico)], E-mail: icampos@ipn.mx; Balankin, A.S. [Instituto Politecnico Nacional, SEPI-ESIME, U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico); Sierra, A.H. [Instituto Politecnico Nacional, UPIICSA, Av. Te 950, Col Granjas, Mexico D.F. 08400 (Mexico); Lopez-Perrusquia, N. [Instituto Politecnico Nacional, SEPI-ESIME, U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico); Escobar-Galindo, R. [Instituto de Ciencia de Materiales de Madrid (CSIC), Cantoblanco, Madrid E-28049 (Spain); Morales-Matamoros, D. [Instituto Mexicano del Petroleo, Eje Lazaro Cardenas Norte, Mexico D.F. 07738 (Mexico)

    2008-12-30

    This study evaluates the morphology of borided interfaces by means of the fractal theory. The boride layers were formed in the AISI M2 steel by applying the paste boriding treatment at temperatures of 1253 and 1273 K and treatment times of 2 and 6 h, while a boron carbide paste thickness of 4 or 5 mm covered the samples surface in order to produce the boron diffusion. The morphology of interfaces formed between FeB and Fe{sub 2}B layers and between Fe{sub 2}B layer and steel substrate was analyzed by the rescaled-range (R/S), root-mean-square (RMS), and Fourier power spectrum (FPS) methods. Moreover, the multi-affine spectra of roughness exponent were obtained by calculating the q-order height-height correlation functions. We found that both interfaces are multi-affine, rather than self-affine. The multi-affine spectra of roughness exponents are found to be different for FeB/Fe{sub 2}B and Fe{sub 2}B/substrate interfaces, but independent on the treatment parameters (boron carbide paste thickness, temperature, and boriding time). Furthermore, we found that the multi-affine spectra of both interfaces behave as it is expected for 'universal multi-fractals' with the Levy index {gamma} = 1, associated with the multiplicative cascades with a log-Cauchy distribution. Furthermore, our data suggest a great homogeneity of the boron diffusion field, characterized by universal fractal dimension D{sub diff} = 2.90 {+-} 0.01. These findings provide a novel insight into the nature of phase formation during the boriding treatment.

  10. Boriding of binary Ni-Ti shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ucar, Nazim; Dogan, Sule [Suleyman Demirel Univ., Isparta (Turkey). Physics Dept.; Karakas, Mustafa Serdar [Cankaya Univ., Ankara (Turkey). Materials Science and Engineering Dept.; Calik, Adnan [Suleyman Demirel Univ., Isparta (Turkey). Manufacturing Engineering Dept.

    2016-07-01

    Boriding of binary Ni-Ti shape memory alloys was carried out in a solid medium at 1273 K for 2, 4, 6, and 8 h using the powder pack method with proprietary Ekabor-Ni powders. Characterization of the boride layer formed on the surface of alloys was done by optical microscopy and scanning electron microscopy. The presence of boride, silicide, and borosilicide phases in the boride layers was confirmed by X-ray diffraction analysis. The thickness and microhardness of the boride layers increased with increasing boriding time. Hardness profiles showed a rapid decrease in hardness moving from the boride layer to the main structure. The high hardness of the boride layer was attributed mainly to the formation of TiB{sub 2}. A parabolic relationship was observed between layer thickness and boriding time, and the growth rate constant for the boriding treatment was calculated as 0.62 x 10{sup -8} cm{sup 2}s{sup -1}.

  11. Fracture Microindentation on boride layers on AISI 1020 steel

    Science.gov (United States)

    Prince, M.; Thanu, A. Justin; Arjun, S. L.; Velmurugan, U.; Gopalakrishnan, P.

    2016-02-01

    In this paper, an attempt has been made to enhance the fracture toughness (Kc) of boride layer using multi-component (Ni, Cr and B) laser bonding. The fracture toughness of continuously pack borided, interrupted pack borided and multi-component (Ni, Cr and B) laser borided steel specimens was measured using Vickers microindentation fracture toughness test as per ASTM E384 standard. The fracture toughness of continuously pack borided layer was - 3.3 MPa.m1/2. The fracture toughness of interrupted boride layer was in the range of - 4.9 MPa.m1/2. The fracture toughness of multi-component (Ni, Cr and B) laser borided layer was in the range of 13.8 - 18.3 MPa.m1/2. A significant improvement in fracture toughness of laser treated specimens was observed from the experimental results. This may be due to better distribution of boron, nickel, chromium and other alloying elements due to laser treatment and relatively more uniform boride layer as compared with continuously pack borided layer and interrupted pack borided layer.

  12. Investigation of the diffusion kinetics of borided stainless steels

    Science.gov (United States)

    Kayali, Yusuf

    2013-12-01

    In this study, the kinetics of borides formed on AISI 420, AISI 304 and AISI 304L stainless steels was investigated. Boronizing treatment was carried out using Ekabor-II powders at the processing temperatures of 1123, 1173 and 1223 K for 2, 4 and 6 h. The phases of the boride layers of borided AISI 420, AISI 304 and AISI 304L stainless steels were FeB, Fe2B, CrB and NiB, respectively. The thickness of the boride layer formed on the borided steels ranged from 4.6 to 64 μm depending on the boriding temperature, boriding time and alloying elements of the stainless steels. Depending on the chemical composition, temperature and layer thickness, the activation energies of boron in AISI 420, AISI 304 and AISI 304L stainless steels were found to be 206.161, 234.641 and 222.818 kJ/mol, respectively. The kinetics of growth of the boride layers formed on the AISI 420, AISI 304 and AISI 304L stainless steels and the thickness of the boride layers were investigated.

  13. Preparation of single phase molybdenum boride

    Energy Technology Data Exchange (ETDEWEB)

    Camurlu, Hasan Erdem, E-mail: erdemcamurlu@gmail.com [Akdeniz University, Mechanical Engineering Department, 07058, Antalya (Turkey)

    2011-04-28

    Highlights: > Formation of Mo and a mixture of molybdenum boride phases take place in preparation of molybdenum borides. > It is intricate to prepare single phase molybdenum borides. > Formation of single phase MoB from MoO{sub 3} + B{sub 2}O{sub 3} + Mg mixtures has not been reported previously. > Single phase MoB was successfully prepared through a combination of mechanochemical synthesis and annealing process. - Abstract: The formation of MoB through volume combustion synthesis (VCS), and through mechanochemical synthesis (MCS) followed by annealing has been investigated. MoO{sub 3}, B{sub 2}O{sub 3} and Mg were used as reactants while MgO and NaCl were introduced as diluents. Products were leached in dilute HCl solution and were subjected to X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM) examinations. Mo was the major phase component in the VCS products under all the experimental conditions. Mo{sub 2}B, MoB, MoB{sub 2} and Mo{sub 2}B{sub 5} were found as minor phases. Products of MCS contained a mixture of Mo{sub 2}B, MoB, MoB{sub 2} and Mo. After annealing the MCS product at 1400 deg. C for 3 h, single phase {alpha}-MoB was obtained.

  14. Growth kinetics of boride coatings formed at the surface AISI M2 during dehydrated paste pack boriding

    Energy Technology Data Exchange (ETDEWEB)

    Doñu Ruiz, M.A., E-mail: mdonur0800@alumno.ipn.mx [Universidad Politécnica del Valle de México UPVM, Grupo Ciencia e Ingeniería de Materiales, Av. Mexiquense S/N Esquina Av. Universidad Politécnica, Col Villa Esmeralda, 54910 Tultitlan (Mexico); López Perrusquia, N.; Sánchez Huerta, D. [Universidad Politécnica del Valle de México UPVM, Grupo Ciencia e Ingeniería de Materiales, Av. Mexiquense S/N Esquina Av. Universidad Politécnica, Col Villa Esmeralda, 54910 Tultitlan (Mexico); Torres San Miguel, C.R.; Urriolagoitia Calderón, G.M. [Instituto Politécnico Nacional, SEPI-ESIME, Unidad Profesional Adolfo López Mateos Zacatenco, Edificio 5, 2do. Piso, Col. Lindavista, CP 07738 México, D.F. (Mexico); Cerillo Moreno, E.A. [Universidad Politécnica del Valle de México UPVM, Grupo Ciencia e Ingeniería de Materiales, Av. Mexiquense S/N Esquina Av. Universidad Politécnica, Col Villa Esmeralda, 54910 Tultitlan (Mexico); Cortes Suarez, J.V. [Univerisdad Autónoma Metropolitana Unidad Azcapotzalco, Av. San Pablo 180 Azcapotzalco 02200, Área de Ciencia de los Materiales, México, D.F. (Mexico)

    2015-12-01

    The growth kinetics of the boride coatings (FeB and Fe{sub 2}B) at the surface of AISI M2 high speed steels were studied in this work. Boriding thermochemical treatment was carried out by dehydrated paste pack at three different temperatures 1173, 1223, and 1273 K and four exposure times 1, 3, 5, and 7 h, respectively. The presence of FeB and Fe{sub 2}B phases was identified by scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS) and X-ray diffraction method. In order to obtain the boron diffusion coefficients at the FeB/Fe{sub 2}B boride coatings, a mathematical model based on the mass balance at the growing interfaces was proposed under certain assumptions. Likewise the parabolic growth constants and the boride incubation time were established as a function of the parameters η (T) and ε (T). The activation energy values estimated for the FeB and Fe{sub 2}B layers were 233.42 and 211.89 kJ mol{sup −1} respectively. A good agreement was obtained between the simulated values of boride layer thicknesses and the experimental results. Finally, empirical relationships of boride coating thickness as a function of boriding temperature and time are presented. - Highlights: • Formed boride coatings at the surface of AISI M2 high speed steels by new process dehydrated paste pack boriding. • The model was based on the mass balance equation at the FeB/Fe{sub 2}B and Fe{sub 2}B/Fe interfaces by considering the boride incubation time. • A good agreement was obtained between the simulated values of boride layers coatings and the experimental results.

  15. Carbide and boride laser modification of steels

    Science.gov (United States)

    Major, Boguslaw; Ebner, Reinhold

    1997-10-01

    Microstructure modification by laser remelting or laser alloying was studied on carbon Ck45 and high speed steels. Laser remelting of Ck45 by overlapping laser tracks led to a great refinement of martensitic structure, especially in the heat affected zone of subsequent laser track. High speed steel (HSS) M2 after laser remelting showed, beside the tetragonal martensite, the diffraction lines of cubic carbides of the M6C and M12C types. Laser alloying of M2 HSS using vanadium carbide (VC) additions caused increasing of eutectic in the interdendritic space, which was accompanied with reduction of the M6C and rising of the MC. M2 HSS laser alloyed with molybdenum carbide (Mo2C) showed formation of the M6C for the hipereutectic compositions while at the highest concentrations of molybdenum, primary dendrites of the M2C and stabilized ferrite were stated. High additions of borides: CrB or VB2; developed formation of the primary borides of blocky type containing a high amount of W, Cr or W, V, respectively. Laser alloying of Ck45 by means of: CrB, VB2 and B4C showed: in the case of CrB an eutectic (alpha) '/M3(C,B)/M2B as well as primary precipitates of the M2B phase for hipereutectic compositions; by adding VB2, the M3B2 and M2B phases were identified experimentally for hipereutectic concentrations; for alloying using B4C, the cellular dendritic structure together with primary borides of the (tau) -M23(C,B)6 phase were stated for hipereutectic compositions. The phase diagrams of M2 HSS + (VC or Mo2C) as well as Ck45 + B4C systems were calculated to predict changes of the constitutions due to laser alloying. Comparison of the solidification structures established experimentally with the calculated phase diagrams revealed a good correlation for the carbides, especially.

  16. Effect of boron paste thickness on the growth kinetics of polyphase boride coatings during the boriding process

    Energy Technology Data Exchange (ETDEWEB)

    Campos, I. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Mechanical Department, Calle del Puente 222 Col., Ejidos de Huipulco, Mexico, DF 14380 (Mexico)]. E-mail: ivan.campos@itesm.mx; Torres, R. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Mechanical Department, Calle del Puente 222 Col., Ejidos de Huipulco, Mexico, DF 14380 (Mexico); Bautista, O. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Mechanical Department, Calle del Puente 222 Col., Ejidos de Huipulco, Mexico, DF 14380 (Mexico); Ramirez, G. [IPN-SEPI-ESIME, U.P. Adolfo Lopez Mateos, Zacatenco, Mexico, DF 07738 (Mexico); Zuniga, L. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Mechanical Department, Calle del Puente 222 Col., Ejidos de Huipulco, Mexico, DF 14380 (Mexico)

    2006-01-15

    The growth kinetics of FeB and Fe{sub 2}B phases forming on AISI M2 steel by paste boriding was studied using different values of paste thickness, treating temperature and exposure time. The growth of iron boride layers is described by the mass balance equation between phases in thermodynamic equilibrium, assuming that the boron concentration at the interfaces remain constant during the treatment. The experimental results show that boron mobility and growth kinetics of iron borides are considerably increased when the paste thickness is increased at constant values of temperature and exposure time.

  17. Critical scattering of neutrons from terbium

    DEFF Research Database (Denmark)

    Als-Nielsen, Jens Aage; Dietrich, O.W.; Marshall, W.

    1968-01-01

    The inelasticity of the critical scattering of neutrons in terbium has been measured above the Neél temperature at the (0, 0, 2−Q) satellite position. The results show that dynamic slowing down of the fluctuations does occur in a second‐order phase transition in agreement with the general theory...

  18. Semiconductor composition containing iron, dysprosium, and terbium

    Energy Technology Data Exchange (ETDEWEB)

    Pooser, Raphael C.; Lawrie, Benjamin J.; Baddorf, Arthur P.; Malasi, Abhinav; Taz, Humaira; Farah, Annettee E.; Kalyanaraman, Ramakrishnan; Duscher, Gerd Josef Mansfred; Patel, Maulik K.

    2017-09-26

    An amorphous semiconductor composition includes 1 to 70 atomic percent iron, 15 to 65 atomic percent dysprosium, 15 to 35 atomic percent terbium, balance X, wherein X is at least one of an oxidizing element and a reducing element. The composition has an essentially amorphous microstructure, an optical transmittance of at least 50% in at least the visible spectrum and semiconductor electrical properties.

  19. Investigation of diffusion kinetics of plasma paste borided AISI 8620 ...

    Indian Academy of Sciences (India)

    Abstract. In the present study, AISI 8620 steel was plasma paste borided by using various B2O3 paste mixture. The plasma paste boriding process was carried out in a dc plasma system at temperatures of 973, 1023 and 1073 K for 2, 5 and 7 h in a gas mixture of 70% H2 -30% Ar under a constant pressure of 10 mbar.

  20. Investigation of diffusion kinetics of plasma paste borided AISI 8620 ...

    Indian Academy of Sciences (India)

    ... diffraction, Vickers micro-hardness tester and the growth kinetics of the boride layers. X-ray diffraction analysis of boride layers on the surface of the steel revealed FeB and Fe2B phases. Depending on temperature and layer thickness, the activation energies of boron in steel were found to be 124.7 kJ/mol for 100% B2O3.

  1. Binary and Ternary Explorations of the Molybdenum Boride System

    OpenAIRE

    Dismukes, Avalon Hope

    2015-01-01

    Refractory metal borides have recently generated intense interest in materials chemistry. These compounds have been shown to possess many advantageous properties, such as exceptionally high hardness, electrical conductivity, and even superconductivity. Higher molybdenum borides are discussed as compounds of interest in this category of materials. However, the complex phase relationships in the molybdenum-boron system complicate the preparation of phase-pure samples. MoB2 and Mo2B4 have both b...

  2. PECULIARITIES OF BORIDE COATING FORMATION MADE OF COMPOSITE METAL-THERMAL POWDER MEDIA

    Directory of Open Access Journals (Sweden)

    N. A. Galynskaya

    2011-01-01

    Full Text Available The paper has investigated an influence of compositions pertaining to complex powder metal-thermal saturating media for boriding on phase-, structure formation and properties of boride coatings in respect of carbon steel.

  3. Characterisation of Wear Resistant Boride Layers on a Tool Steel by Activity Controlled Pack Boronising

    DEFF Research Database (Denmark)

    Fernandes, Frederico Augusto Pires; Christiansen, Thomas Lundin; Somers, Marcel A. J.

    2015-01-01

    The present work addresses the production and characterisation of iron boride layers by pack boronising of a Vanadis 6 tool steel. The boride layers were produced at 900°C for 2h using different pack compositions in order to obtain a single-phase boride layer. The layers were characterized by ele...

  4. The characterization of boride layer on the St37 iron

    Science.gov (United States)

    Sutrisno, Soegijono, Bambang

    2012-06-01

    The property such as microhardness of boride layer formed on St37 iron was investigated. Boronizing was carried out in a solid medium consisting of nano size powders of 50% B4C as a donor, 45% SiC as a diluent, and 5% KBF4 as an activator treated at the temperature of 1000°C for 8 hours. The phases that were formed on the substrate was found as Fe2B and FeB layer that had smooth and flate shape morphology. The hardness of boride layer on St37 was over 2000 HV, while the hardness of untreated St37 iron was about 123,82 HV. Depending on process time and temperature, the depth of boride layer ranges from 20 to 60 μm, leading to a diffusion controlled process.

  5. Corrosion behavior of boride layers evaluated by the EIS technique

    Energy Technology Data Exchange (ETDEWEB)

    Campos, I. [Instituto Politecnico Nacional. SEPI-ESIME U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico)], E-mail: icampos@ipn.mx; Palomar-Pardave, M. [Universidad Autonoma Metropolitana-Azcapotzalco, Materials Department, Avenue San Pablo 180 Col. Reynosa Tamaulipas, Mexico D.F. 02200 (Mexico); Amador, A. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico); VillaVelazquez, C. [Instituto Politecnico Nacional. SEPI-ESIME U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico); Hadad, J. [Tecnologico de Monterrey, Campus Ciudad de Mexico, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico)

    2007-09-30

    The corrosion behavior of boride layers at the AISI 304 steel surface is evaluated in the present study. Electrochemical impedance spectroscopy (EIS) technique was used for the evaluation of the polarization resistance at the steel surface, with the aid of AUTOLAB potentiostat. Samples were treated with boron paste thickness of 4 and 5 mm, in the range of temperatures 1123 {<=} T {<=} 1273 K and exposed time of 4 and 6 h. The electrochemical technique employed 10 mV AC with a frequency scan range from 8 kHz to 3 mHz in deaerated 0.1 M NaCl solution. Nyquist diagrams show that the highest values of corrosion resistance are present in the samples borided at the temperature of 1273 K, with treatment time of 4 h and 4 mm of boron paste thickness. The values of corrosion resistance on borided steels are compared with the porosity exhibited in the layers.

  6. Laser borided composite layer produced on austenitic 316L steel

    Directory of Open Access Journals (Sweden)

    Mikołajczak Daria

    2016-12-01

    Full Text Available Abstract Austenitic 316L steel is well-known for its good resistance to corrosion and oxidation. Therefore, this material is often used wherever corrosive media or high temperatures are to be expected. The main drawback of this material is very low hardness and low resistance to mechanical wear. In this study, the laser boriding was used in order to improve the wear behavior of this material. As a consequence, a composite surface layer was produced. The microstructure of laser-borided steel was characterized by only two zones: re-melted zone and base material. In the re-melted zone, a composite microstructure, consisting of hard ceramic phases (borides and a soft austenitic matrix, was observed. A significant increase in hardness and wear resistance of such a layer was obtained.

  7. Pulsed nanocrystalline plasma electrolytic boriding as a novel ...

    Indian Academy of Sciences (India)

    WINTEC

    of the porous complex titanium borided layer. Large val- ues of polarization resistance (Rp) are also noted in all the samples. A high Rp value is an indication of the working electrode strongly resisting change from its equilibrium state and corresponds to a low rate of titanium ion re- lease. This behaviour is clearly noted and ...

  8. Pulsed nanocrystalline plasma electrolytic boriding as a novel ...

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 30; Issue 6. Pulsed nanocrystalline plasma electrolytic boriding as a novel method for corrosion protection of CP-Ti (Part 1: Different frequency and duty cycle). M Kh Aliev A Saboor. Alloys and Steels Volume 30 Issue 6 December 2007 pp 601-605 ...

  9. Equilibrium And Growth Morphologies Of Trinickel Boride Ni3b ...

    African Journals Online (AJOL)

    The morphology of the trinickel boride Ni3B precipitates during slow cooling in differential thermal analysis (DTA) has been investigated using high resolution electron microscopy (HREM). Due to the large development of the facets of the type {022}, the crystal tends towards an equilibrium morphology whereas the growth ...

  10. Growth kinetics of boride layers formed on 99.0% purity nickel

    Indian Academy of Sciences (India)

    The boride layer was characterized by optical microscopy, X-ray diffraction technique and micro-Vickers hardness tester. X-ray diffraction analysis revealed the existence of NiB, Ni2B, Ni3B and Ni4B3 compounds at the surface of borided Nickel 201 alloy. The thickness of the boride layer increased with an increase in the ...

  11. Hard Surface Layers by Pack Boriding and Gaseous Thermo-Reactive Deposition and Diffusion Treatments

    DEFF Research Database (Denmark)

    Christiansen, Thomas Lundin; Bottoli, Federico; Dahl, Kristian Vinter

    2017-01-01

    Thermo-reactive deposition and diffusion (TRD) and boriding are thermochemical processes that result in very high surface hardness by conversion of the surface into carbides/nitrides and borides, respectively. These treatments offer significant advantages in terms of hardness, adhesion, tribo......-based borides. The obtained surface layers were characterized with X-ray diffraction, scanning electron microscopy, reflected light microscopy, and micro-indentation....

  12. Fracture Toughness of Thick Boride Layers Estimated by the Cross-Sectioned Scratch Test

    Science.gov (United States)

    Campos-Silva, I.; Flores-Jiménez, M.; Bravo-Bárcenas, D.; Rodríguez-Castro, G.; Martínez-Trinidad, J.; Meneses-Amador, A.

    2018-01-01

    New results about the fracture toughness (K c) of thick boride layers estimated by the cross-sectioned scratch test are presented in this study. The FeB-Fe2B layers developed at the surface of borided AISI 1018 and AISI 1045 steels and the Fe2B layer formed on the borided AISI 1045 steel exposed to a diffusion annealing process (DAP) were used for this purpose. The cross-sectioned scratch tests were performed with a Vickers diamond stylus drawn across the thick boride layer under a constant load to produce a half-cone-shaped fracture near to the top surface of the borided steels. The height of the half-cone-shaped fracture as a function of the cross-sectioned scratch loads was used to determine the fracture toughness of the FeB and Fe2B layers. The results showed a fracture resistance of ˜2.8 {MPa}√ m for the FeB layer formed at the surface of borided AISI 1045 steel. Likewise, the effect of the DAP on the surface of the borided AISI 1045 steel promoted the formation of an exclusively Fe2B layer, with an increase in the fracture toughness of the whole boride layer around 5 {MPa}√ m . Finally, the principle of the technique can be used to minimize the influence of the anisotropic properties on the fracture toughness along the depth of boride layers.

  13. Raman spectroscopy study of the doping effect of the encapsulated terbium halogenides on single-walled carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Kharlamova, M.V.; Kramberger, C.; Mittelberger, A. [University of Vienna, Faculty of Physics, Vienna (Austria)

    2017-04-15

    In the present work, the doping effect of terbium chloride, terbium bromide, and terbium iodide on single-walled carbon nanotubes (SWCNTs) was compared by Raman spectroscopy. A precise investigation of the doping-induced alterations of the Raman modes of the filled SWCNTs was conducted. The shifts of the components of the Raman modes and modification of their profiles allowed concluding that the inserted terbium halogenides have acceptor doping effect on the SWCNTs, and the doping efficiency increases in the line with terbium iodide, terbium bromide, and terbium chloride. (orig.)

  14. Characterization and diffusion model for the titanium boride layers formed on the Ti6Al4V alloy by plasma paste boriding

    Science.gov (United States)

    Keddam, Mourad; Taktak, Sukru

    2017-03-01

    The present study is focused on the estimation of activation energy of boron in the plasma paste borided Ti6Al4V alloy, which is extensively used in technological applications, using an analytical diffusion model. Titanium boride layers were successfully produced by plasma paste boriding method on the Ti6Al4V alloy in the temperature range of 973-1073 K for a treatment time ranging from 3 to 7 h. The presence of both TiB2 top-layer and TiB whiskers sub-layer was confirmed by the XRD analysis and SEM observations. The surface hardness of the borided alloy was evaluated using Micro-Knoop indenter. The formation rates of the TiB2 and TiB layers were found to have a parabolic character at all applied process temperatures. A diffusion model was suggested to estimate the boron diffusivities in TiB2 and TiB layers under certain assumptions, by considering the effect of boride incubation times. Basing on own experimental data on boriding kinetics, the activation energies of boron in TiB2 and TiB phases were estimated as 136.24 ± 0.5 and 63.76 ± 0.5 kJ mol-1, respectively. Finally, the obtained values of boron activation energies for Ti6Al4V alloy were compared with the data available in the literature.

  15. Magnetocaloric effect of thin Terbium films

    Science.gov (United States)

    Mello, V. D.; Anselmo, D. H. A. L.; Vasconcelos, M. S.; Almeida, N. S.

    2017-12-01

    We report a theoretical study of the magnetocaloric effect of Terbium (Tb) thin films due to finite size and surface effects in the helimagnetic phase, corresponding to a temperature range from TC=219 K to TN=231 K, for external fields of the order of kOe. For a Tb thin film of 6 monolayers submitted to an applied field (ΔH =30 kOe, ΔH =50 kOe and ΔH = 70 kOe) we report a significative change in adiabatic temperature, ΔT / ΔH , near the Néel temperature, of the order ten times higher than that observed for Tb bulk. On the other hand, for small values of the magnetic field, large thickness effects are found. For external field strength around few kOe, we have found that the thermal caloric efficiency increases remarkably for ultrathin films. For an ultrathin film with 6 monolayers, we have found ΔT / ΔH = 43 K/T while for thicker films, with 20 monolayers, ΔT / ΔH = 22 K/T. Our results suggest that thin films of Tb are a promising material for magnetocaloric effect devices for applications at intermediate temperatures.

  16. Femtosecond XUV spectroscopy of gadolinium and terbium

    Energy Technology Data Exchange (ETDEWEB)

    Carley, Robert; Frietsch, Bjoern; Doebrich, Kristian; Teichmann, Martin; Gahl, Cornelius; Noack, Frank [Max-Born-Institute, Berlin (Germany); Schwarzkopf, Olaf; Wernet, Philippe [Helmholtz-Zentrum fuer Materialien und Energie (BESSY II), Berlin (Germany); Weinelt, Martin [Max-Born-Institute, Berlin (Germany); Fachbereich Physik, Freie Universitaet, Berlin (Germany)

    2011-07-01

    We present recent results of time-resolved IR-pump-XUV-probe experiments on the ultrafast demagnetization of thin films of Gadolinium(0001) and Terbium(0001) on Tungsten(110). The experiments are the first to be done using a newly developed high-order harmonics (HHG) XUV beamline at the MBI. The beamline delivers monochromated XUV pulses of approximately 150 fs duration with a photon energy resolution of up to 150 meV. Following excitation by intense femtosecond infrared (IR) pulses, photoemission with 35 eV photons allows us to directly probe the 4f electrons and their interaction with the valence band, both in the bulk and at the surface, to follow the ultrafast magnetization dynamics in the Lanthanide metals. As signatures of ultrafast demagnetization of the metal by the IR pulse, we see for the first time, rapid strong reduction of the exchange splitting in the valence band. This is followed by a slower demagnetization due to the spin-lattice interaction.

  17. Transition metal borides. Synthesis, characterization and superconducting properties

    Energy Technology Data Exchange (ETDEWEB)

    Kayhan, Mehmet

    2013-07-12

    A systematic study was done on the synthesis and superconducting properties of metal rich transition metal borides. Five different binary systems were investigated including the boride systems of niobium, tantalum, molybdenum, tungsten and rhenium. High temperature solid state methods were used in order to synthesize samples of different transition metal borides of the composition M{sub 2}B, MB, M{sub 3}B{sub 2}, MB{sub 2}, and M{sub 2}B{sub 4}. The reactions were carried out in three different furnaces with different sample containers: the electric arc (copper crucible), the high frequency induction furnace (boron nitride, tantalum or glassy carbon crucibles), and the conventional tube furnace (sealed evacuated quartz ampoules). The products obtained were characterized with X-ray powder diffractometry, scanning electron microscopy and energy-dispersive X-ray spectroscopy. Phase analyses and crystal structure refinements using the Rietveld method and based on structure models known from literature were performed. A neutron diffraction measurement was done for W{sub 2}B{sub 4} to allow for a complete crystal structure determination, because of the presence of a heavy element like tungsten and a light element like boron that made it difficult to determine the accurate determination of the boron atom positions and occupancies from X-ray data. A new structure model for W{sub 2}B{sub 4} was proposed. Magnetic measurements in a SQUID magnetometer down to temperatures as low as 1.8 K were performed to several of the products in order to see if the transition metal borides become superconducting at low temperatures, and the results were compared with data from literature. Superconducting properties were found for the following compounds: NbB{sub 2} (T{sub C} = 3.5 K), β-MoB (T{sub C} = 2.4 K), β-WB (T{sub C} = 2.0 K), α-WB (T{sub C} = 4.3 K), W{sub 2}B{sub 4} (T{sub C} = 5.4 K), Re{sub 7}B{sub 3} (T{sub C} = 2.4 K). A relationship between the superconducting properties

  18. Effect of Fe2B boride orientation on abrasion wear resistance of Fe-B cast alloy

    Directory of Open Access Journals (Sweden)

    Da-wei Yi

    2017-07-01

    Full Text Available The microstructures and abrasion wear resistance of directional solidification Fe-B alloy have been investigated using optical microscopy, X-ray diffraction, scanning electron microscopy and laser scanning microscopy. The results show that the microstructure of as-cast Fe-B alloy consists of ferrite, pearlite and eutectic boride. After heat treatment, the microstructure is composed of boride and martensite. The plane which is perpendicular to the boride growth direction possesses the highest hardness. In two-body abrasive wear tests, the silicon carbide abrasive can cut the boride and martensite matrix synchronously, and the wear mechanism is micro cutting mechanism. The worn surface roughness and the wear weight loss both increase with the increasing contact load. Moreover, when the boride growth direction is perpendicular to the worn surface, the highest hardness plane of the boride can effectively oppose abrasion, and the martensite matrix can surround and support borides perfectly.

  19. Electron momentum distribution and electronic response of ceramic borides

    Energy Technology Data Exchange (ETDEWEB)

    Heda, N.L. [Department of Pure and Applied Physics, University of Kota, Kota 324005 (India); Meena, B.S.; Mund, H.S. [Department of Physics, Mohanlal Sukhadia University, Udaipur 313001 (India); Sahariya, Jagrati [Department of Physics, Manipal University, Jaipur 303007 (India); Kumar, Kishor [Department of Physics, Mohanlal Sukhadia University, Udaipur 313001 (India); Ahuja, B.L., E-mail: blahuja@yahoo.com [Department of Physics, Mohanlal Sukhadia University, Udaipur 313001 (India)

    2017-03-15

    Isotropic Compton profiles of transition metal based ceramics TaB and VB have been measured using {sup 137}Cs (661.65 keV) γ-ray Compton spectrometer. The experimental momentum densities are compared with those deduced using linear combination of atomic orbitals (LCAO) with Hartree-Fock (HF), density functional theory (DFT) with Wu-Cohen generalized gradient approximation (WCGGA) and also the hybridization of HF and DFT (namely B3PW and PBE0) schemes. It is found that LCAO-DFT-WCGGA scheme based profiles give an overall better agreement with the experimental data, for both the borides. In addition, we have computed the Mulliken's population (MP) charge transfer data, energy bands, density of states and Fermi surface topology of both the borides using full potential-linearized augmented plane wave (FP-LAPW) and LCAO methods with DFT-WCGGA scheme. Cross-overs of Fermi level by the energy bands corresponding to B-2p and valence d-states of transition metals lead to metallic character in both the compounds. Equal-valence-electron-density profiles and MP analysis suggest more ionic character of VB than that of TaB.

  20. New route toward nanosized crystalline metal borides with tuneable stoichiometry and variable morphologies

    OpenAIRE

    Gouget, Guillaume; Beaunier, Patricia; Portehault, David; Sanchez, Clément

    2016-01-01

    International audience; Herein we highlight for the first time the ability to tune the stoichiometry of metal boride nanocrystals through nanoparticle synthesis in thermally stable inorganic molten salts. Two metal-boron systems are chosen as case studies: boron-poor nickel borides and boron-rich yttrium borides. We show that NiB, Ni4B3, Ni2B, Ni3B, and YB6 particles can be obtained as crystalline phases with good selectivity. Anisotropic crystallization is observed in two cases: the first bo...

  1. Phase composition and crack resistance of alloy boride layers on steel

    Science.gov (United States)

    Kholin, A. S.

    1999-04-01

    Alloying of boride layers on steel changes their phase composition, morphology, and structure. Chromium and manganese diminish the fraction of the eutectic in the layer. B-Cr and B-Mn coats do not contain monoborides. B, B-Mo, and B-Mo-W coats consist of two layers, i.e., monoborides and diborides. The other studied coats are represented by a diboride with inclusions of a monoboride. Molybdenum intensifies the texture of the FeB boride as compared with a purely boride layer; the other elements weaken it considerably.

  2. Green fluorescence of terbium ions in lithium fluoroborate glasses ...

    Indian Academy of Sciences (India)

    Glasses; terbium ion; oscillator strengths; fluorescence; lifetimes; fibre lasers. 1. Introduction. Today glasses are most favourable engineering materials for abundant applications due to the wide ability of property altering by compositional modifications. The considerable examination of glass science to achieve required ...

  3. Green fluorescence of terbium ions in lithium fluoroborate glasses ...

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 39; Issue 3. Green fluorescence of terbium ions in lithium fluoroborate glasses for fibre lasers and display devices. G R DILLIP C MADHUKAR REDDY M RAJESH SHIVANAND CHAURASIA B DEVA PRASAD RAJU S W JOO. Volume 39 Issue 3 June 2016 pp 711-717 ...

  4. In Situ Solid-Gas Reactivity of Nanoscaled Metal Borides from Molten Salt Synthesis

    OpenAIRE

    Gouget, Guillaume; Debecker, Damien P.; Kim, Ara; Olivieri, Giorgia; Gallet, Jean-Jacques; Bournel, Fabrice; Thomas, Cyril; Ersen, Ovidiu; Moldovan, Simona; Sanchez, Clément; Carenco , Sophie; Portehault, David

    2017-01-01

    Metal borides have mostly been studied as bulk materials. The nanoscale provides new opportunities to investigate the properties of these materials, e.g., nanoscale hardening and surface reactivity. Metal borides are often considered stable solids because of their covalent character, but little is known on their behavior under a reactive atmosphere, especially reductive gases. We use molten salt synthesis at 750 °C to provide cobalt monoboride (CoB) nanocrystals embedded in an amorphous layer...

  5. Synthesis, Structure, and Properties of Refractory Hard-Metal Borides

    Science.gov (United States)

    Lech, Andrew Thomas

    As the limits of what can be achieved with conventional hard compounds, such as tungsten carbide, are nearing reach, super-hard materials are an area of increasing industrial interest. The refractory hard metal borides, such as ReB2 and WB4, offer an increasingly attractive alternative to diamond and cubic boron nitride as a next-generation tool material. In this Thesis, a thorough discussion is made of the progress achieved by our laboratory towards understanding the synthesis, structure, and properties of these extremely hard compounds. Particular emphasis is placed on structural manipulation, solid solution formation, and the unique crystallographic manifestations of what might also be called "super-hard metals".

  6. Metal Borohydrides synthesized from metal borides and metal hydrides

    DEFF Research Database (Denmark)

    Sommer, Sanna

    2014-01-01

    Aarhus C, Denmark email: gallafogh@hotmail.com / sanna-sommer@hotmail.com Magnesium boride, MgB2, ball milled with MH (M = Li, Na, Ca) followed by hydrogenation under high hydrogen pressure, readily forms the corresponding metal borohydrides, M(BH4)x (M = Li, Na, Ca) and MgH2 according to reaction scheme...... crystallization processes. In situ SR-PXD of the systems was the most promising, revealing the formation of β-Ca(BH4)2 similar to the the MgB2 – CaH2 system [5]. This connection stems from the similarities in the crystal structure of AlB2 and MgB2. MgB2 has also shown ability to form LiBH4 and NaBH4. However...

  7. Effect of boron paste thickness on the growth kinetics of Fe{sub 2}B boride layers during the boriding process

    Energy Technology Data Exchange (ETDEWEB)

    Campos, I. [ITESM-CCM Mechanical Department, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico)]. E-mail: ivan.campos@itesm.mx; Bautista, O. [ITESM-CCM Mechanical Department, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico); Ramirez, G. [IPN-SEPI-ESIME, U.P. Adolfo Lopez Mateos, Zacatenco, Mexico D.F. 07738 (Mexico); Islas, M. [ITESM-CCM Mechanical Department, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico); Parra, J. de la [ITESM-CCM Mechanical Department, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico); Zuniga, L. [ITESM-CCM Mechanical Department, Calle del Puente 222 Col. Ejidos de Huipulco, Mexico D.F. 14380 (Mexico)

    2005-04-30

    Through this work we study the influence of the thickness of boron paste in the growth of Fe{sub 2}B boride layer during the paste boriding thermochemical treatment applied on AISI 1045 steel. Different thickness of boron paste over the material surface with constant temperature and time show the variability of the diffusion coefficient of boron in Fe{sub 2}B phase depending, basically, on the boron potential at the external surface of the substrate. The mobility of boron in the formed phase is determined by the balance mass equation that considers the concentration profiles in the corresponding interphases layer-substrate, the thermodynamic equilibrium in the growth of the iron boride layer and the experimental results obtained during the process.

  8. Two-level systems and negative thermal expansion of lutetium borides

    Science.gov (United States)

    Novikov, V. V.; Mitroshenkov, N. V.; Kornev, B. I.; Matovnikov, A. V.

    2017-05-01

    The heat capacity Cv(T) and unit cell volume V(T) temperature dependencies of lutetium borides LuB2 and LuB4 in the region of 2-300 K were analysed in the Debye-Einstein approximation. The characteristic temperatures of the Debye and Einstein components of boride heat capacity and thermal expansion were found. The anomalous contribution to the borides' thermal characteristics was revealed. This contribution was attributed to the influence of two-level systems (TLS), formed in the subsystem of lutetium ions due to asymmetry in the way they are surrounded by the boron atoms in the boride crystal structure. The TLS influence is revealed on heat capacity temperature dependencies by the Schottky-type maxima at Tmax LuB2 =13.8 K, Tmax LuB4 =22.7 K, as well as by the negative contribution to the borides' thermal expansion. The borides' Grüneisen parameters corresponding to the heat capacity and thermal expansion TLS anomalies are negative, and amount to several 10 s of units.

  9. Boron-Based Hydrogen Storage: Ternary Borides and Beyond

    Energy Technology Data Exchange (ETDEWEB)

    Vajo, John J. [HRL Laboratories, LLC, Malibu, CA (United States)

    2016-04-28

    DOE continues to seek reversible solid-state hydrogen materials with hydrogen densities of ≥11 wt% and ≥80 g/L that can deliver hydrogen and be recharged at moderate temperatures (≤100 °C) and pressures (≤100 bar) enabling incorporation into hydrogen storage systems suitable for transportation applications. Boron-based hydrogen storage materials have the potential to meet the density requirements given boron’s low atomic weight, high chemical valance, and versatile chemistry. However, the rates of hydrogen exchange in boron-based compounds are thus far much too slow for practical applications. Although contributing to the high hydrogen densities, the high valance of boron also leads to slow rates of hydrogen exchange due to extensive boron-boron atom rearrangements during hydrogen cycling. This rearrangement often leads to multiple solid phases occurring over hydrogen release and recharge cycles. These phases must nucleate and react with each other across solid-solid phase boundaries leading to energy barriers that slow the rates of hydrogen exchange. This project sought to overcome the slow rates of hydrogen exchange in boron-based hydrogen storage materials by minimizing the number of solid phases and the boron atom rearrangement over a hydrogen release and recharge cycle. Two novel approaches were explored: 1) developing matched pairs of ternary borides and mixed-metal borohydrides that could exchange hydrogen with only one hydrogenated phase (the mixed-metal borohydride) and only one dehydrogenated phase (the ternary boride); and 2) developing boranes that could release hydrogen by being lithiated using lithium hydride with no boron-boron atom rearrangement.

  10. Terahertz Cherenkov radiation from ultrafast magnetization in terbium gallium garnet

    Science.gov (United States)

    Gorelov, S. D.; Mashkovich, E. A.; Tsarev, M. V.; Bakunov, M. I.

    2013-12-01

    We report an experimental observation of terahertz Cherenkov radiation from a moving magnetic moment produced in terbium gallium garnet by a circularly polarized femtosecond laser pulse via the inverse Faraday effect. Contrary to some existing theoretical predictions, the polarity of the observed radiation unambiguously demonstrates the paramagnetic, rather than diamagnetic, nature of the ultrafast inverse Faraday effect. From measurements of the radiation field, the Verdet constant in the subpicosecond regime is ˜3-10 times smaller than its table quasistatic value.

  11. In Situ Solid-Gas Reactivity of Nanoscaled Metal Borides from Molten Salt Synthesis.

    Science.gov (United States)

    Gouget, Guillaume; Debecker, Damien P; Kim, Ara; Olivieri, Giorgia; Gallet, Jean-Jacques; Bournel, Fabrice; Thomas, Cyril; Ersen, Ovidiu; Moldovan, Simona; Sanchez, Clément; Carenco, Sophie; Portehault, David

    2017-08-07

    Metal borides have mostly been studied as bulk materials. The nanoscale provides new opportunities to investigate the properties of these materials, e.g., nanoscale hardening and surface reactivity. Metal borides are often considered stable solids because of their covalent character, but little is known on their behavior under a reactive atmosphere, especially reductive gases. We use molten salt synthesis at 750 °C to provide cobalt monoboride (CoB) nanocrystals embedded in an amorphous layer of cobalt(II) and partially oxidized boron as a model platform to study morphological, chemical, and structural evolutions of the boride and the superficial layer exposed to argon, dihydrogen (H2), and a mixture of H2 and carbon dioxide (CO2) through a multiscale in situ approach: environmental transmission electron microscopy, synchrotron-based near-ambient-pressure X-ray photoelectron spectroscopy, and near-edge X-ray absorption spectroscopy. Although the material is stable under argon, H2 triggers at 400 °C decomposition of CoB, leading to cobalt(0) nanoparticles. We then show that H2 activates CoB for the catalysis of CO2 methanation. A similar decomposition process is also observed on NiB nanocrystals under oxidizing conditions at 300 °C. Our work highlights the instability under reactive atmospheres of nanocrystalline cobalt and nickel borides obtained from molten salt synthesis. Therefore, we question the general stability of metal borides with distinct compositions under such conditions. These results shed light on the actual species in metal boride catalysis and provide the framework for future applications of metal borides in their stability domains.

  12. New route toward nanosized crystalline metal borides with tuneable stoichiometry and variable morphologies.

    Science.gov (United States)

    Gouget, Guillaume; Beaunier, Patricia; Portehault, David; Sanchez, Clément

    2016-10-06

    Herein we highlight for the first time the ability to tune the stoichiometry of metal boride nanocrystals through nanoparticle synthesis in thermally stable inorganic molten salts. Two metal-boron systems are chosen as case studies: boron-poor nickel borides and boron-rich yttrium borides. We show that NiB, Ni4B3, Ni2B, Ni3B, and YB6 particles can be obtained as crystalline phases with good selectivity. Anisotropic crystallization is observed in two cases: the first boron-rich YB4 nanorods are reported, while boron-poor NiB nanoparticles show a peculiar crystal habit, as they are obtained as spheres with uniaxial defects related to the crystal structure. Crystallization mechanisms are proposed to account for the appearance of these two kinds of anisotropy at the nanoscale.

  13. Hardness optimization of boride diffusion layer on Astm F-75 alloy using response surface methodology

    Energy Technology Data Exchange (ETDEWEB)

    Arguelles O, J. L.; Corona R, M. A. [Universidad Autonoma de San Luis Potosi, Doctorado Institucional en Ingenieria y Ciencia de Materiales, San Luis Potosi 78000, SLP (Mexico); Marquez H, A.; Saldana R, A. L.; Saldana R, A. [Universidad de Guanajuato, Ingenieria Mecanica Agricola DICIVA, Irapuato, Guanajuato 36500 (Mexico); Moreno P, J., E-mail: amarquez@ugto.mx [Universidad de Guanajuato, Departamento de Minas, Metalurgia y Geologia, Ex-Hacienda San Matias s/n, Guanajuato, Guanajuato 36020 (Mexico)

    2017-11-01

    In this study, the Response Surface Methodology (Rsm) and Central Composite Design (Ccd) were used to optimize the hardness of boride diffusion layer on Astm F-75 alloy (also called Haynes alloy). A boronizing thermochemical treatment was carried out at different temperatures and for different time periods. Hardness tests were conducted. The boride diffusion layer was verified by the X-ray diffraction (XRD) analysis indicating the formation of Co B, Co{sub 2}B, Cr B and Mo{sub 2}B phases. An optimal hardness of 3139.7 Hv was obtained for the samples subjected to the boriding process for a duration of 6.86 h at 802.4 degrees Celsius. (Author)

  14. Metal-boride phase formation on tungsten carbide (WC-Co) during microwave plasma chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, Jamin M.; Catledge, Shane A., E-mail: catledge@uab.edu

    2016-02-28

    Graphical abstract: - Highlights: • A detailed phase analysis after PECVD boriding shows WCoB, CoB and/or W{sub 2}CoB{sub 2}. • EDS of PECVD borides shows boron diffusion into the carbide grain structure. • Nanoindentation hardness and modulus of borides is 23–27 GPa and 600–780 GPa. • Scratch testing shows hard coating with cracking at 40N and spallation at 70N. - Abstract: Strengthening of cemented tungsten carbide by boriding is used to improve the wear resistance and lifetime of carbide tools; however, many conventional boriding techniques render the bulk carbide too brittle for extreme conditions, such as hard rock drilling. This research explored the variation in metal-boride phase formation during the microwave plasma enhanced chemical vapor deposition process at surface temperatures from 700 to 1100 °C. We showed several well-adhered metal-boride surface layers consisting of WCoB, CoB and/or W{sub 2}CoB{sub 2} with average hardness from 23 to 27 GPa and average elastic modulus of 600–730 GPa. The metal-boride interlayer was shown to be an effective diffusion barrier against elemental cobalt; migration of elemental cobalt to the surface of the interlayer was significantly reduced. A combination of glancing angle X-ray diffraction, electron dispersive spectroscopy, nanoindentation and scratch testing was used to evaluate the surface composition and material properties. An evaluation of the material properties shows that plasma enhanced chemical vapor deposited borides formed at substrate temperatures of 800 °C, 850 °C, 900 °C and 1000 °C strengthen the material by increasing the hardness and elastic modulus of cemented tungsten carbide. Additionally, these boride surface layers may offer potential for adhesion of ultra-hard carbon coatings.

  15. Surface hardening of St41 low carbon steel by using the hot-pressing powder-pack boriding method

    Science.gov (United States)

    Sutrisno, Soegijono, Bambang

    2014-03-01

    This research describes a powder-pack boriding process by using hot-pressing technic for St41 low carbon steel which will improve the hardness on the substrate by forming boride layer solid solution. Those method can reduce the operational cost of the research if it is compared by the conventional method with the asmospheric condition both vacuum system and gas inert condition. The concept of boriding by hot-pressing technic was verified in a laboratory scale. Welldefined and reusedable technic was achieved by using the stainless steel 304 as the container and sealed with a 5 ton pressure. This container was filled boronizing powder consisting of 5%B4C, 90%SiC, and 5%KBF4 to close the St41 low carbon steel specimen inside the container. The St41 boriding specimen was treated at the temperature of 900°C for 8 hours. The boride layer on the substrate was found as FeB and Fe2B phase with the hardness about 1800 HV. This value was more than ten times if compared with the untreated specimen that only had the hardness of 123 HV. Depend on heat treatment temperature, heat treatment time, and powder-pack boriding pressure, the depth of boride layer range from 127 to 165 μm, leading to a diffusion controlled process.

  16. Growth kinetics of boride layers formed on 99.0% purity nickel

    Indian Academy of Sciences (India)

    1Department of Metallurgical and Materials Engineering, Faculty of Technology, Afyon Kocatepe University,. 03200 Afyonkarahisar, Turkey. 2Laboratory of Materials Technology, Faculty of Mechanical Engineering and Process Engineering, USTHB, B.P. No. 32, ... in a negative effect on the boride layer in terms of both.

  17. Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

    Science.gov (United States)

    Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

    2017-11-01

    The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

  18. Ultra-Fast Boriding in High-Temperature Materials Processing Industries

    Energy Technology Data Exchange (ETDEWEB)

    None

    2008-12-01

    This factsheet describes a research project whose main objective is to further develop, optimize, scale-up, and commercialize an ultra-fast boriding (also referred to as “boronizing”) process that can provide much higher energy efficiency, productivity, and near-zero emissions in many of the high-temperature materials processing industries.

  19. Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

    Science.gov (United States)

    Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

    2017-10-01

    The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

  20. Terbium luminescence in alumina xerogel fabricated in porous anodic alumina matrix under various excitation conditions

    Energy Technology Data Exchange (ETDEWEB)

    Gaponenko, N. V., E-mail: nik@nano.bsuir.edu.by [Belarusian State University of Informatics and Radioelectronics (Belarus); Kortov, V. S. [Yeltsin Ural Federal University (Russian Federation); Orekhovskaya, T. I.; Nikolaenko, I. A. [Belarusian State University of Informatics and Radioelectronics (Belarus); Pustovarov, V. A.; Zvonarev, S. V.; Slesarev, A. I. [Yeltsin Ural Federal University (Russian Federation); Prislopski, S. Ya. [National Academy of Sciences of Belarus, Stepanov Institute of Physics (Belarus)

    2011-07-15

    Terbium-doped alumina xerogel layers are synthesized by the sol-gel method in pores of a porous anodic alumina film 1 {mu}m thick with a pore diameter of 150-180 nm; the film is grown on a silicon substrate. The fabricated structures exhibit terbium photoluminescence with bands typical of trivalent terbium terms. Terbium X-ray luminescence with the most intense band at 542 nm is observed for the first time for such a structure. Morphological analysis of the structure by scanning electron microscopy shows the presence of xerogel clusters in pore channels, while the main pore volume remains unfilled and pore mouths remain open. The data obtained confirm the promising applications of fabricated structures for developing matrix converters of X-rays and other ionizing radiations into visible light. The possibilities of increasing luminescence intensity in the matrix converter are discussed.

  1. Optical Properties of Lithium Terbium Fluoride and Implications for Performance in High Power Lasers (Postprint)

    Science.gov (United States)

    2016-02-01

    AFRL-RX-WP-JA-2016-0323 OPTICAL PROPERTIES OF LITHIUM TERBIUM FLUORIDE AND IMPLICATIONS FOR PERFORMANCE IN HIGH POWER LASERS... AMERICA (STINFO COPY) AIR FORCE RESEARCH LABORATORY MATERIALS AND MANUFACTURING DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433-7750 AIR...OPTICAL PROPERTIES OF LITHIUM TERBIUM FLUORIDE AND IMPLICATIONS FOR PERFORMANCE IN HIGH POWER LASERS (POSTPRINT) 5a. CONTRACT NUMBER IN-HOUSE 5b

  2. Detection of biothiols in cells by a terbium chelate-Hg (II) system

    Science.gov (United States)

    Tan, Hongliang; Chen, Yang

    2012-01-01

    Great efforts have been devoted to the development of sensitive and specific analysis methods for biothiols because of their important roles in biological systems. We present a new detection system for biothiols that is based on the reversible quenching and restoration of fluorescence of terbium chelate caused by Hg2+ and thiol species. In the presence of biothiols, a restoration of fluorescence of terbium chelate after quenching by Hg2+ was observed due to the interaction of Hg2+ with thiol groups, and the restored fluorescence increased with the concentration of biothiols. This method was sensitive and selective for biothiols. The detection limit was 80 nM for glutathione, 100 nM for Hcy, and 400 nM for Cysteine, respectively. The terbium chelate-Hg (II) system was successfully applied to determine the levels of biothiols in cancer cells and urine samples. Further, it was also shown to be comparable to Ellman's assay. Compared to other fluorescence methods, the terbium chelate probe is advantageous because interference from short-lived nonspecific fluorescence can be efficiently eliminated due to the long fluorescence lifetime of terbium chelate, which allows for detection by time-resolved fluorescence. The terbium chelate probe can serve as a diagnostic tool for the detection of abnormal levels of biothiols in disease.

  3. Signs of superconductivity at 110 K on inclusions of TiB sub k boride phases into titanium matrix

    CERN Document Server

    Volkov, V V; Berzverkhij, P P; Martynets, V G; Matizen, E V

    2002-01-01

    Verification of theoretical forecasts on the possibility of the high-temperature superconductivity of the high-temperature superconductivity (HTSC) in the TiB sub k titanium borides is accomplished. It is established that the jump-like change in the temperature dependence of the electric resistance R(T) at 110 K takes place on the titanium samples, the surfaces whereof are coated with the borides diffusion layers of the TiB sub k variable in-depth composition. This proves the presence of the borides diffusion layers are applied onto the metallic titanium by means of treating its surface with the B sub 2 H sub 6 + H sub 2 gases mixture at the temperature of 610-700 deg C with the subsequent annealing in vacuum. The boride layers composition is studied through the mass-spectrometry method

  4. Cryogenic temperature characteristics of Verdet constant of terbium sesquioxide ceramics

    Science.gov (United States)

    Snetkov, I. L.; Palashov, O. V.

    2016-12-01

    The dependence of the Verdet constant on temperature in the (80-300 K) range for a promising magneto-active material terbium sesquioxide Tb2O3 at the wavelengths of 405-1064 nm is considered. For each of the studied wavelengths, the Verdet constant of the material cooled down to the liquid nitrogen temperature increased by more than a factor of 3.2 as compared to the room temperature value. Similarly to the other paramagnetics, the increase follows the law ∼1/T. Approximations for the temperature dependence of the Verdet constant have been obtained and the value of 1/V·(dV/dT) has been estimated. This information is needed to determine the angle of rotation as well as the variation of the extinction ratio of a Faraday isolator with temperature and extremely important at creation a cryogenic Faraday devices.

  5. Biogenic terbium oxide nanoparticles as the vanguard against osteosarcoma

    Science.gov (United States)

    Iram, Sana; Khan, Salman; Ansary, Abu Ayoobul; Arshad, Mohd; Siddiqui, Sahabjada; Ahmad, Ejaz; Khan, Rizwan H.; Khan, Mohd Sajid

    2016-11-01

    The synthesis of inner transition metal nanoparticles via an ecofriendly route is quite difficult. This study, for the first time, reports synthesis of terbium oxide nanoparticles using fungus, Fusarium oxysporum. The biocompatible terbium oxide nanoparticles (Tb2O3 NPs) were synthesized by incubating Tb4O7 with the biomass of fungus F. oxysporum. Multiple physical characterization techniques, such as UV-visible and photoluminescence spectroscopy, TEM, SAED, and zeta-potential were used to confirm the synthesis, purity, optical and surface characteristics, crystallinity, size, shape, distribution, and stability of the nanoemulsion of Tb2O3 NPs. The Tb2O3 NPs were found to inhibit the propagation of MG-63 and Saos-2 cell-lines (IC50 value of 0.102 μg/mL) and remained non-toxic up to a concentration of 0.373 μg/mL toward primary osteoblasts. Cell viability decreased in a concentration-dependent manner upon exposure to 10 nm Tb2O3 NPs in the concentration range 0.023-0.373 μg/mL. Cell toxicity was evaluated by observing changes in cell morphology, cell viability, oxidative stress parameters, and FACS analysis. Morphological examinations of cells revealed cell shrinkage, nuclear condensation, and formation of apoptotic bodies. The level of ROS within the cells-an indicator of oxidative stress was significantly increased. The induction of apoptosis at concentrations ≤ IC50 was corroborated by 4‧,6-diamidino-2-phenylindole dihydrochloride (DAPI) staining (DNA damage and nuclear fragmentation). Flow-cytometric studies indicated that the response was dose dependent with a threshold effect.

  6. The Relationship of the Chemical Bonding Topology of High Critical Temperature Copper Oxide Superconductors to that of the Chevrel Phases and the Ternary Lanthanide Rhodium Borides.

    Science.gov (United States)

    1987-12-11

    to those of the ternary molybdenum chalcogenides and ternary lanthanide rhodium borides in which the conducting skeleton is constructed from metal...Bonding Topology of High Critical Temperature Copper Oxide Superconductors to That of The Chevrel Phases and the Ternary Lanthanide Rhodium Borides by R...REPORT NUMBER P Rhodium Borides 7 AUTHOR(s ) S. CONTRACT OR GRANT NUMIER(*) f, % .0, R.B. King N00014-84-K-0365 S. PERFORMING ORGANIZATION NAME AND

  7. Friction and wear of radiofrequency-sputtered borides, silicides, and carbides

    Science.gov (United States)

    Brainard, W. A.; Wheeler, D. R.

    1978-01-01

    The friction and wear properties of several refractory compound coatings were examined. These compounds were applied to 440 C bearing steel surfaces by radiofrequency (RF) sputtering. The refractory compounds were the titanium and molybdenum borides, the titanium and molybdenum silicides, and the titanium, molybdenum, and boron carbides. Friction testing was done with a pin-on-disk wear apparatus at loads from 0.1 to 5.0 newtons. Generally, the best wear properties were obtained when the coatings were bias sputtered onto 440 C disks that had been preoxidized. Adherence was improved because of the better bonding of the coatings to the iron oxide formed during preoxidation. As a class the carbides provided wear protection to the highest loads. Titanium boride coatings provided low friction and good wear properties to moderate loads.

  8. Electrosynthesis of tantalum borides in oxygen-free and oxygen-containing fluoride melts

    DEFF Research Database (Denmark)

    Polyakova, L.P.; Polyakov, E.G.; Makarova, O.V.

    2001-01-01

    Results of electrosynthesis of tantalum borides in fluoride and oxyfluoride melts are compared. It is shown that the single-phase X-ray-amorphous micro-layered coatings form only in the latter case. Linear and square-wave voltammetry, complemented by X-ray diffraction analysis, IR spectroscopy......, and OC, reveals that the reason for their formation is the cathodic reduction of heteronuclear tantalum and boron complexes....

  9. Preparation of molybdenum borides by combustion synthesis involving solid-phase displacement reactions

    Energy Technology Data Exchange (ETDEWEB)

    Yeh, C.L. [Department of Mechanical and Automation Engineering, Da-Yeh University, 112 Shan-Jiau Rd., Da-Tsuen, Changhua 51505, Taiwan (China)], E-mail: clyeh@mail.dyu.edu.tw; Hsu, W.S. [Department of Mechanical and Automation Engineering, Da-Yeh University, 112 Shan-Jiau Rd., Da-Tsuen, Changhua 51505, Taiwan (China)

    2008-06-12

    Preparation of molybdenum borides of five different phases in the Mo-B binary system (including Mo{sub 2}B, MoB, MoB{sub 2}, Mo{sub 2}B{sub 5}, and MoB{sub 4}) was performed by self-propagating high-temperature synthesis (SHS) with two kinds of the reactant samples. When elemental powder compacts with an exact stoichiometry corresponding to the boride phase were employed, self-sustaining reaction was only achieved in the sample with Mo:B = 1:1 and nearly single-phase MoB was yielded. Therefore, the other four boride compounds were prepared from the reactant compacts composed of MoO{sub 3}, Mo, and B powders, within which the displacement reaction of MoO{sub 3} with boron was involved in combustion synthesis. Experimental evidence shows that the extent of displacement reaction in the overall reaction has a significant impact on sustainability of the synthesis reaction, combustion temperature, reaction front velocity, and composition of the end product. An increase in the solid-phase displacement reaction taking place during the SHS process contributes more heat flux to the synthesis reaction, thus resulting in the increase of combustion temperature and enhancement of the reaction front velocity. Based upon the XRD analysis, formation of Mo{sub 2}B, MoB{sub 2}, and Mo{sub 2}B{sub 5} as the dominant boride phase in the end product was successful through the SHS reaction with powder compacts under appropriate stoichiometries between MoO{sub 3}, Mo, and B. However, a poor conversion was observed in the synthesis of MoB{sub 4}. The powder compact prepared for the production of MoB{sub 4} yielded mostly Mo{sub 2}B{sub 5}.

  10. Influence of Re Concentration on the Mechanical Properties of Tungsten Borides from First-Principles Calculations

    Science.gov (United States)

    Pan, Yong; Lin, Yuanhua

    2017-10-01

    Tungsten borides are promising high-temperature materials. However, the structure and hardening mechanisms of tungsten boride are still great challenges. To solve the problems, we apply the first-principles method to study the structure of WB3 and explore the influence of alloying element Re on the mechanical properties of WB3. The calculated Vickers hardness of WB3 is 39.1 GPa. We further find that a low concentration of Re can improve the hardness of WB3, which is in good agreement with the experimental result. However, the hardness and elastic properties of WB3 decrease gradually with increasing Re concentration. The calculated results show that the structure and hardness of WB3 are attributed to the B-B hexagonal prism. A high concentration of Re weakens the charge interaction between the B-B atoms, and reduces the mechanical properties of WB3. Therefore, we can adjust the alloy concentration to improve the Vickers hardness of transition metal borides.

  11. Structure of superhard tungsten tetraboride: A missing link between MB2 and MB12 higher borides

    Science.gov (United States)

    Lech, Andrew T.; Turner, Christopher L.; Mohammadi, Reza; Tolbert, Sarah H.; Kaner, Richard B.

    2015-01-01

    Superhard metals are of interest as possible replacements with enhanced properties over the metal carbides commonly used in cutting, drilling, and wear-resistant tooling. Of the superhard metals, the highest boride of tungsten—often referred to as WB4 and sometimes as W1–xB3—is one of the most promising candidates. The structure of this boride, however, has never been fully resolved, despite the fact that it was discovered in 1961—a fact that severely limits our understanding of its structure–property relationships and has generated increasing controversy in the literature. Here, we present a new crystallographic model of this compound based on refinement against time-of-flight neutron diffraction data. Contrary to previous X-ray–only structural refinements, there is strong evidence for the presence of interstitial arrangements of boron atoms and polyhedral bonding. The formation of these polyhedra—slightly distorted boron cuboctahedra—appears to be dependent upon the defective nature of the tungsten-deficient metal sublattice. This previously unidentified structure type has an intermediary relationship between MB2 and MB12 type boride polymorphs. Manipulation of the fractionally occupied metal and boron sites may provide insight for the rational design of new superhard metals. PMID:25733870

  12. Structure of superhard tungsten tetraboride: a missing link between MB2 and MB12 higher borides.

    Science.gov (United States)

    Lech, Andrew T; Turner, Christopher L; Mohammadi, Reza; Tolbert, Sarah H; Kaner, Richard B

    2015-03-17

    Superhard metals are of interest as possible replacements with enhanced properties over the metal carbides commonly used in cutting, drilling, and wear-resistant tooling. Of the superhard metals, the highest boride of tungsten--often referred to as WB4 and sometimes as W(1-x)B3--is one of the most promising candidates. The structure of this boride, however, has never been fully resolved, despite the fact that it was discovered in 1961--a fact that severely limits our understanding of its structure-property relationships and has generated increasing controversy in the literature. Here, we present a new crystallographic model of this compound based on refinement against time-of-flight neutron diffraction data. Contrary to previous X-ray-only structural refinements, there is strong evidence for the presence of interstitial arrangements of boron atoms and polyhedral bonding. The formation of these polyhedral--slightly distorted boron cuboctahedra--appears to be dependent upon the defective nature of the tungsten-deficient metal sublattice. This previously unidentified structure type has an intermediary relationship between MB2 and MB12 type boride polymorphs. Manipulation of the fractionally occupied metal and boron sites may provide insight for the rational design of new superhard metals.

  13. Autofluorescence-free Live-cell Imaging Using Terbium Nanoparticles.

    Science.gov (United States)

    Cardoso Dos Santos, Marcelina; Goetz, Joan; Bartenlian, Hortense; Wong, Ka-Leung; Charbonniere, Loïc Joanny; Hildebrandt, Niko

    2018-02-20

    Fluorescent nanoparticles (NPs) have become irreplaceable tools for advanced cellular and sub-cellular imaging. While very bright NPs require excitation with UV or visible light, which can create strong autofluorescence of biological components, NIR-excitable NPs without autofluorescence issues exhibit much lower brightness. Here, we show the application of a new type of surface-photosensitized terbium NPs (Tb-NPs) for autofluorescence-free intracellular imaging in live HeLa cells. Combination of exceptionally high brightness, high photostability, and long photoluminecence (PL) lifetimes for highly efficient suppression of the short-lived autofluorescence, allowed for time-gated PL imaging of intracellular vesicles over 72 h without toxicity and at extremely low Tb-NP concentrations down to 12 pM. Detection of highly resolved long-lifetime (ms) PL decay curves from small (~10 µm2) areas within single cells within a few seconds emphasized the unprecedented photophysical properties of Tb-NPs for live-cell imaging that extend well beyond currently available nanometric imaging agents.

  14. Solar Thermochemical Hydrogen Production via Terbium Oxide Based Redox Reactions

    Directory of Open Access Journals (Sweden)

    Rahul Bhosale

    2016-01-01

    Full Text Available The computational thermodynamic modeling of the terbium oxide based two-step solar thermochemical water splitting (Tb-WS cycle is reported. The 1st step of the Tb-WS cycle involves thermal reduction of TbO2 into Tb and O2, whereas the 2nd step corresponds to the production of H2 through Tb oxidation by water splitting reaction. Equilibrium compositions associated with the thermal reduction and water splitting steps were determined via HSC simulations. Influence of oxygen partial pressure in the inert gas on thermal reduction of TbO2 and effect of water splitting temperature (TL on Gibbs free energy related to the H2 production step were examined in detail. The cycle (ηcycle and solar-to-fuel energy conversion (ηsolar-to-fuel efficiency of the Tb-WS cycle were determined by performing the second-law thermodynamic analysis. Results obtained indicate that ηcycle and ηsolar-to-fuel increase with the decrease in oxygen partial pressure in the inert flushing gas and thermal reduction temperature (TH. It was also realized that the recuperation of the heat released by the water splitting reactor and quench unit further enhances the solar reactor efficiency. At TH=2280 K, by applying 60% heat recuperation, maximum ηcycle of 39.0% and ηsolar-to-fuel of 47.1% for the Tb-WS cycle can be attained.

  15. Folate Receptor Targeted Alpha-Therapy Using Terbium-149

    CERN Document Server

    Müller, Cristina; Haller, Stephanie; Dorrer, Holger; Köster, Ulli; Johnston, Karl; Zhernosekov, Konstantin; Türler, Andreas; Schibli, Roger

    2014-01-01

    Terbium-149 is among the most interesting therapeutic nuclides for medical applications. It decays by emission of short-range α-particles (Eα = 3.967 MeV) with a half-life of 4.12 h. The goal of this study was to investigate the anticancer efficacy of a 149Tb-labeled DOTA-folate conjugate (cm09) using folate receptor (FR)-positive cancer cells in vitro and in tumor-bearing mice. 149Tb was produced at the ISOLDE facility at CERN. Radiolabeling of cm09 with purified 149Tb resulted in a specific activity of ~1.2 MBq/nmol. In vitro assays performed with 149Tb-cm09 revealed a reduced KB cell viability in a FR-specific and activity concentration-dependent manner. Tumor-bearing mice were injected with saline only (group A) or with 149Tb-cm09 (group B: 2.2 MBq; group C: 3.0 MBq). A significant tumor growth delay was found in treated animals resulting in an increased average survival time of mice which received 149Tb-cm09 (B: 30.5 d; C: 43 d) compared to untreated controls (A: 21 d). Analysis of blood parameters rev...

  16. Hardness and dielectric characteristics of flux grown terbium aluminate crystals

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, K.K.; Kotru, P.N. [Jammu Univ. (India). Dept. of Physics; Tandon, R.P. [National Physical Laboratory, New Delhi (India); Wanklyn, B.M. [Clarendon Laboratory, University of Oxford, Oxford (United Kingdom)

    1999-01-29

    Results of indentation induced Vickers hardness testing and dielectric studies conducted on flux-grown terbium aluminate crystals are presented. It is shown that the Vickers hardness value (H{sub v}) is independent of indentation time, but depends on the applied load. Applying the concept of Hays and Kendall, the load independent values are estimated for (110) and (001) planes. Differential behaviour in the crack formation of two different planes (110) and (001) is observed, while (001) plane develops Palmqvist cracks in the whole load range of 10-100 g, (110) plane shows a transition from Palmqvist to median cracks at 70 g. The fracture toughness, brittleness index and yield strength are determined for both the planes. The hardness anisotropy is reported. The dielectric constant, dielectric loss and conductivity are shown to be dependent on temperature and frequency of the applied a.c. field. The dielectric constant versus temperature shows a transition peak at 230 C, which remains independent of the frequency of the applied a.c. field in the range 1 kHz-13 MHz. (orig.) 36 refs.

  17. Effect of High Configuration Entropy and Rare Earth Addition on Boride Precipitation and Mechanical Properties of Multi-principal-Element Alloys

    Science.gov (United States)

    Zhang, H.; Zhong, X. C.; He, Y. Z.; Li, W. H.; Wu, W. F.; Chen, G.; Guo, S.

    2017-08-01

    A series of multi-principal-element (MPE) alloys have been prepared by adding Ni, Mn, Al, Cu and Y into the reference CoCrFe-B alloy. The microstructure and mechanical properties of these MPE alloys have been investigated thoroughly. It is found that the addition of the elements can inhibit boride precipitation in the designed alloys and the solid solution strengthening effect induced by interstitial boron atoms is more significant than that by boride precipitation. The MPE alloys with the fcc phase as the main solid solution phase have a higher boron solubility and hence less boride precipitation, than those with the bcc phase as the main solid solution phase. The addition of yttrium can improve the boron solubility, decrease boride precipitation, control the boride morphology and, importantly, simultaneously improve the compressive strength and ductility of boron-containing MPE alloys.

  18. The Hardness of Boride Layer on the S45C Iron (A preliminary study on surface hardening of ferrous material

    Directory of Open Access Journals (Sweden)

    Sutrisno

    2012-08-01

    Full Text Available The property such as microhardness of boride layer formed on S45C iron was investigated. Boronizing was carried out in a solid medium consisting of nano size powders of 50% B4C as a donor, 45% SiC as a diluent, and 5% KBF4 as an activator treated at the temperature of 10000C for 8 hours. The phases that were formed on the substrate was found as Fe2B and FeB layer that had smooth and flate shape morphology. The hardness of boride layer on S45C was over 2000 HV, while the hardness of untreated S45C iron was about 196,39 HV. Depending on process time and temperature, the depth of boride layer ranges from 25 to 55 µm, leading to a diffusion controlled process

  19. Thermoluminescence of cerium and terbium -doped calcium pyrophosphate

    Energy Technology Data Exchange (ETDEWEB)

    Roman L, J.; Cruz Z, E. [UNAM, Instituto de Ciencias Nucleares, Circuito Exterior, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Lozano R, I. B.; Diaz G, J. A. I., E-mail: jesus.roman@nucleares.unam.mx [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Av. Legaria No. 694, 11500 Mexico D. F. (Mexico)

    2015-10-15

    The aim of this work is to report the thermoluminescence (Tl) response of Calcium Pyrophosphate phosphor doped with Cerium and Terbium impurities (Ca{sub 2}P{sub 2}O{sub 7}:Ce{sup 3+},Tb{sup 3+}). The phosphors were synthesized using the co-precipitation method and annealed at 900 degrees C by two hours for obtain the β phase. The intentional doping with Ce and Tb ions was 1 at.% and 0.1 at.%, whereas in the EDS results the concentration of impurities was 0.39 at.% and 0.05 at.%, respectively. The superficial morphology of phosphor is mainly composed by thin wafers of different size. All samples were exposed to gamma rays from {sup 60}Co in the Gammacell-200 irradiator. The Tl response of the phosphor was measured from Rt up to 350 degrees C and under nitrogen atmosphere in a Harshaw TLD 3500 reader. The glow curves of the Ca{sub 2}P{sub 2}O{sub 7}:Ce{sup 3+},Tb{sup 3+} powders showed a broad intense Tl peak centered at 165 degrees C and a shoulder at approximate 260 degrees C was observed. A linear Tl response in the range of absorbed dose of 0.2 to 10 Gy was obtained. Tl glow curves were analyzed using the initial rise (IR)and computerized glow curve deconvolution methods to evaluate the kinetics parameters such as activation energy (E), frequency factor (s) and kinetic order (b). (Author)

  20. Solvent polarity and oxygen sensitivity, rather than viscosity, determine lifetimes of biaryl-sensitised terbium luminescence.

    Science.gov (United States)

    Walter, Edward R H; Williams, J A Gareth; Parker, David

    2017-12-14

    In a macrocyclic terbium complex incorporating a biaryl sensitiser, the observed variation of emission lifetime is shown to be determined by the solubility of oxygen in the solvent system and the relative energy of the chromophore excited state, rather than any dependence on solvent viscosity.

  1. Response of boride coating on the Ti-6Al-4V alloy to corrosion and fretting corrosion behavior in Ringer's solution for bio-implant application

    Science.gov (United States)

    Bose, Sivakumar; Pathak, Lokesh Chandra; Singh, Raghuvir

    2018-03-01

    Corrosion and fretting corrosion of boride coating on Ti-6Al-4V (TAV) are investigated in Ringer's solution for bio-implant applications. Boride coatings are fabricated as a function of temperature (900-1100 °C) and soaking time (1-5 h). Coatings are characterized for phase evaluation, microstructural analysis, thickness and microhardness measurement. The coating contained TiB2 and TiB whiskers as outermost and inner layers respectively. The increasing thickness of outer TiB2 at a relatively higher boriding temperature and time impeded the TiB formation. A large microhardness value of ∼3248 Hv15gf at the outermost surface (corrosion resistance of coating produced at increased temperature and time of boriding, yet remained lower than the resistance of bare TAV alloy. The formation of B2O3 and absence of Al2O3 on the surface, as investigated by X-ray photoelectron spectroscopy (XPS), are attributed to an inferior corrosion resistance of the borided TAV. The increase in corrosion resistance with the TiB2 coating thickness is attributed to thickening of the inner passive film formed on borided TAV. A large decrease in fretting damage after boride coating is due to the decline in a synergistic parameter.

  2. Increasing the Surface Hardness of Cast Iron by Electrodeposition of Borides in Molten Salts

    Directory of Open Access Journals (Sweden)

    Al-Azzawi A.H.

    2017-06-01

    Full Text Available In this paper the electrodeposition of boron on the surface of cast iron as a coating is applied to increase the hardness and protect the substrate against abrasive wear. The boron containing coating was synthesized by electrodeposition process from a NaCl-KCl (1:1 mol-10 w%NaF-10w% KBF4 molten salt. The effect of electrolysis parameters (temperature and time on the hardness is presented; the current density varied in the range −37 – −4.5 mA/cm2, allowing perfect coverage of and respect for dimensions. The electrochemical process was carried out at different temperatures (750°C-900°C and for different periods of time (5-10 hours. Depending on the current density and duration of electrolysis, the deposits consist of FeB or Fe2B. Microhardness measurements across the boride layer indicated very high hardness values (between 1600 and 2100 HV0.05. The structure of the boride layer is linked to its boron content and thermal history: as-deposited coatings present very small grain sizes and can be considered as nearly amorphous.

  3. Boron-dependency of molybdenum boride electrocatalysts for the hydrogen evolution reaction

    Energy Technology Data Exchange (ETDEWEB)

    Park, Hyounmyung; Encinas, Andrew; Fokwa, Boniface P.T. [Department of Chemistry, University of California, Riverside, CA (United States); Department of Chemical and Environmental Engineering, University of California, Riverside, CA (United States); Scheifers, Jan P.; Zhang, Yuemei [Department of Chemistry, University of California, Riverside, CA (United States)

    2017-05-08

    Molybdenum-based materials have been considered as alternative catalysts to noble metals, such as platinum, for the hydrogen evolution reaction (HER). We have synthesized four binary bulk molybdenum borides Mo{sub 2}B, α-MoB, β-MoB, and MoB{sub 2} by arc-melting. All four phases were tested for their electrocatalytic activity (linear sweep voltammetry) and stability (cyclic voltammetry) with respect to the HER in acidic conditions. Three of these phases were studied for their HER activity and by X-ray photoelectron spectroscopy (XPS) for the first time; MoB{sub 2} and β-MoB show excellent activity in the same range as the recently reported α-MoB and β-Mo{sub 2}C phases, while the molybdenum richest phase Mo{sub 2}B show significantly lower HER activity, indicating a strong boron-dependency of these borides for the HER. In addition, MoB{sub 2} and β-MoB show long-term cycle stability in acidic solution. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  4. Boron-Dependency of Molybdenum Boride Electrocatalysts for the Hydrogen Evolution Reaction.

    Science.gov (United States)

    Park, Hyounmyung; Encinas, Andrew; Scheifers, Jan P; Zhang, Yuemei; Fokwa, Boniface P T

    2017-05-08

    Molybdenum-based materials have been considered as alternative catalysts to noble metals, such as platinum, for the hydrogen evolution reaction (HER). We have synthesized four binary bulk molybdenum borides Mo2 B, α-MoB, β-MoB, and MoB2 by arc-melting. All four phases were tested for their electrocatalytic activity (linear sweep voltammetry) and stability (cyclic voltammetry) with respect to the HER in acidic conditions. Three of these phases were studied for their HER activity and by X-ray photoelectron spectroscopy (XPS) for the first time; MoB2 and β-MoB show excellent activity in the same range as the recently reported α-MoB and β-Mo2 C phases, while the molybdenum richest phase Mo2 B show significantly lower HER activity, indicating a strong boron-dependency of these borides for the HER. In addition, MoB2 and β-MoB show long-term cycle stability in acidic solution. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Phase Evolution in Boride-Based Cermets and Reaction Bonding onto Plain Low Carbon Steel Substrate

    Science.gov (United States)

    Palanisamy, B.; Upadhyaya, A.

    2012-04-01

    Reaction sinter bonding is a process that aims to bond two materials for improvement in properties through reactive sintering technique. The process has been effectively used to sinter hard materials like borides in situ which not only possess excellent oxidation resistance, good corrosion resistance but also resistant to abrasive wear. Sinter bonding is a unique surface modification process achieved through powder metallurgy and is competent with other techniques like boronizing sintering and sinter-brazing since it eliminates the additional operations of heat treatment and assembly and removes the inherent setbacks with these processes. This study focuses on identifying the phase evolution mechanism using characterization tools like x-ray diffractometry and energy dispersive spectroscopy and study of sinter bonding of the boron containing precursors (Mo-Cr-Fe-Ni-FeB-MoB) onto plain carbon steel. A microstructure containing Fe-based matrix dispersed with complex borides develops with temperature in the tape cast sheets. A fivefold increase in hardness between plain carbon steel in wrought condition and sinter bonded steel was observed. The multilayer consisted of a reaction zone adjacent to the interface and was investigated with the composition profile and hardness measurements. A model of sinter bonding between the cermet and the steel has also been proposed.

  6. Chemical bond in borides. Theoretical and experimental analysis; Chemische Bindung in Boriden. Theoretische und experimentelle Untersuchung

    Energy Technology Data Exchange (ETDEWEB)

    Sagawe, Vanessa

    2013-04-18

    The aim of this work was the analysis of the bonding situation in different borides by examining the electron density in these structures. The main focus of the analysis was on the QTAIM analysis and the evaluation of the Electron Localizability Indicator (ELI-D). For the calculation of the electron density different methods (extended Hueckel, LMTO, (L)APW) were used to prove which method leads to most precise results. The (L)APW-method was found to be the most exact one and the one with the longest computational times. The examined compounds were boron-rich Borides containing icosahedra, Transition Metal Borides and Na{sub 3}B{sub 20}. Most of the structures of the examined boron-rich Borides can be derived directly from the MgB{sub 7} structure type (MgB{sub 7}, MgB{sub 12}C{sub 2}, LiB{sub 13}C{sub 2}, Li{sub 2}B{sub 12}C{sub 2}, LiB{sub 12}PC). The influence of the different cations as well as the interstitial atoms could be analyzed by comparing these compounds. Structures which can be derived from the alpha-rhombohedral Boron were also analyzed (B{sub 12}O{sub 2}, B{sub 12}P{sub 2}, B{sub 12}As{sub 2}). Assuming Bader-Charges the icosahedron is always positively charged if the electronegativity of the interstitial atoms is higher than the electronegativity of the Boron atoms. If their electronegativitiy is lower, the icosahedra are negatively charged. From the ELI-D-basins the bonding situation can be analyzed according to Wade by bisecting the basins of the exohedral bonds. The icosahedra are always negatively charged. However, Wade's rule is never exactly fulfilled as the charge is never exactly -2. To verify the results from theoretical calculations and vice versa, experimental electron density analyses of MgB{sub 7} and Li{sub 2}B{sub 12}C{sub 2} were performed. However, only the examination of MgB{sub 7} gave reliable results. They promoted the results by the calculations and underlined the correctness of the used methods. Results received by single

  7. Wear resistance of laser-deposited boride reinforced Ti-Nb-Zr-Ta alloy composites for orthopedic implants

    Energy Technology Data Exchange (ETDEWEB)

    Samuel, Sonia [Department of Materials Science and Engineering University of North Texas, Denton, TX (United States); Nag, Soumya [Department of Materials Science and Engineering Ohio State University, Columbus, OH (United States); Scharf, Thomas W.; Banerjee, Rajarshi [Department of Materials Science and Engineering University of North Texas, Denton, TX (United States)

    2008-04-01

    The inherently poor wear resistance of titanium alloys limits their application as femoral heads in femoral (hip) implants. Reinforcing the soft matrix of titanium alloys (including new generation {beta}-Ti alloys) with hard ceramic precipitates such as borides offers the possibility of substantially enhancing the wear resistance of these composites. The present study discusses the microstructure and wear resistance of laser-deposited boride reinforced composites based on Ti-Nb-Zr-Ta alloys. These composites have been deposited using the LENS{sup TM} process from a blend of elemental Ti, Nb, Zr, Ta, and boron powders and consist of complex borides dispersed in a matrix of {beta}-Ti. The wear resistance of these composites has been compared with that of Ti-6Al-4V ELI, the current material of choice for orthopedic femoral implants, against two types of counterfaces, hard Si{sub 3}N{sub 4} and softer SS440C stainless steel. Results suggest a substantial improvement in the wear resistance of the boride reinforced Ti-Nb-Zr-Ta alloys as compared with Ti-6Al-4V ELI against the softer counterface of SS440. The presence of an oxide layer on the surface of these alloys and composites also appears to have a substantial effect in terms of enhanced wear resistance.

  8. Simulation of the growth kinetics of the (FeB/Fe 2B) bilayer obtained on a borided stainless steel

    Science.gov (United States)

    Keddam, M.

    2011-01-01

    The present work is an attempt to simulate the growth kinetics of the (FeB/Fe 2B) bilayer grown on a substrate made of AISI 316 stainless steel by the application of the powder-pack boriding process, and using four different temperatures (1123, 1173, 1223 and 1273 K) and five exposure times (2, 4, 6, 8 and 10 h). The adopted diffusion model solves the mass balance equation at each growth front: (FeB/Fe 2B or FeB/substrate) under certain assumptions and without considering the diffusion zone. To consider the effect of the incubation times for the borides formation, the temperature-dependent function ϕ( T) was incorporated in the model. To validate this model, a computer code written in Matlab (version 6.5), was developed with the purpose of simulating the kinetics of the boride layers. This computer code uses the following parameters as input data: (the boriding temperature, the treatment time, the upper and lower limits of boron concentration in each iron boride, the diffusion coefficients of boron in the FeB and Fe 2B phases as well as the ϕ( T) parameter). The outputs of the computer code are the parabolic growth constant at each growth front and the thicknesses of the FeB and Fe 2B layers. A good agreement was obtained between the experimental parabolic growth constants taken from a reference work [I. Campos-Silva et al., Formation and kinetics of FeB/Fe 2B layers and diffusion zone at the surface of AISI 316 borided steels, Surf. Coat Technol., 205 (2010) 403-412] and the simulated values of the parabolic growth constants ( kFeB and k1). The present model was also able to predict the thicknesses of the FeB and Fe 2B layers at a temperature of 1243 K during 3 and 5 h. In addition, the mass gain at the material surface was also estimated as a function of the time and the upper boron content in each iron boride phase. It was shown that the simulated values of the generated mass gain are very sensitive to the increase of both temperature and the upper boron

  9. High Temperature Sliding Wear of NiAl-based Coatings Reinforced by Borides

    Directory of Open Access Journals (Sweden)

    Oleksandr UMANSKYI

    2016-05-01

    Full Text Available The development of composite materials (CM in the systems “metal-refractory compound” is one of the up-to-date trends in design of novel materials aimed at operating under the conditions of significant loads at high temperature. To design such material, NiAl, which is widely used for deposition of protective coatings on parts of gas-turbine engines, was selected for a matrix. To strengthen a NiAl under the conditions of intense wear and a broad temperature range (up to 1000 °C, it is reasonable to add refractory inclusions. Introduction of refractory borides into matrix leads to a marked increase in metal wear resistance. In order to research the behavior of the designed composites at high temperatures and to study the influence of oxides on the friction processes, the authors carried out high temperature oxidation of CM of the above systems at 1000 °С for 90 min. It was determined that all of the composites were oxidized selectively and that the thickness of oxide layers formed on the boride inclusions is 3 – 7 times that on the oxides formed on the NiAl matrix. The mechanism of wear of gas-thermal coatings of the NiAl – МеB2 systems was studied for conditions of high temperature tribotests using the «pin-on-disc» technique. The obtained results indicate that introduction of TiB2, CrB2 and ZrB2 leads to their more intense oxidation during high temperature tribotests as compared to the matrix. The oxides formed on refractory borides act as solid lubricants, which promote a decrease in wear of the contact friction pairs. For more detailed investigation of the effect of tribo-oxidation products on the friction processes, tribotests were conducted for prior oxidized (at 900 °С coatings NiAl – 15 wt.% CrB2 (TiB2, ZrB2.DOI: http://dx.doi.org/10.5755/j01.ms.22.1.8093

  10. Arginine-responsive terbium luminescent hybrid sensors triggered by two crown ether carboxylic acids

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Lasheng [Key Laboratory of Theoretical Chemistry of Environment, Ministry of Education, School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Tang, Ke; Ding, Xiaoping [School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Wang, Qianming, E-mail: qmwang@scnu.edu.cn [Key Laboratory of Theoretical Chemistry of Environment, Ministry of Education, School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Zhou, Zhan; Xiao, Rui [School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China)

    2013-12-01

    Crown ether carboxylic acids constitute main building blocks for the synthesis of terbium containing covalent cross-linked luminescent materials. Both the complexes and the hybrid nanomaterials could exhibit remarkable green emissions in pure water. More importantly, they were found to have a profound effect on the luminescence responses to arginine compared with glutamic acid, histidine, tryptophan, threonine, tyrosine and phenylalanine in aqueous environment. The present study provided the possibility of using a host–guest mechanism as a way of signal transduction based on lanthanide supramolecular hybrid materials. - Highlights: • Crown ether carboxylic acids were found to sensitize terbium ions among a group of ethers. • The complexes and silica hybrid materials were both prepared and characterized. • They could exhibit remarkable green emissions in pure water.

  11. Comparative analysis of conjugated alkynyl chromophore-triazacyclononane ligands for sensitized emission of europium and terbium.

    Science.gov (United States)

    Soulié, Marine; Latzko, Frédéric; Bourrier, Emmanuel; Placide, Virginie; Butler, Stephen J; Pal, Robert; Walton, James W; Baldeck, Patrice L; Le Guennic, Boris; Andraud, Chantal; Zwier, Jurriaan M; Lamarque, Laurent; Parker, David; Maury, Olivier

    2014-07-07

    A series of europium and terbium complexes based on a functionalized triazacyclononane carboxylate or phosphinate macrocyclic ligand is described. The influence of the anionic group, that is, carboxylate, methylphosphinate, or phenylphosphinate, on the photophysical properties was studied and rationalized on the basis of DFT calculated structures. The nature, number, and position of electron-donating or electron-withdrawing aryl substituents were varied systematically within the same phenylethynyl scaffold in order to optimize the brightness of the corresponding europium complexes and investigate their two-photon absorption properties. Finally, the europium complexes were examined in cell-imaging applications, and selected terbium complexes were studied as potential oxygen sensors. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Spectrofluorimetric Determination of Human Serum Albumin Using Terbium-Danofloxacin Probe

    OpenAIRE

    Ramezani, Amir M.; Manzoori, Jamshid L.; Amjadi, Mohammad; Jouyban, Abolghasem

    2012-01-01

    A spectrofluorimetric method is proposed for the determination of human serum albumin (HSA) and bovine serum albumin (BSA) using terbium-danofloxacin (Tb3+-Dano) as a fluorescent probe. These proteins remarkably enhance the fluorescence intensity of the Tb3+-Dano complex at 545 nm, and the enhanced fluorescence intensity of Tb3+-Dano is proportional to the concentration of proteins (HSA and BSA). Optimum conditions for the determination of HSA were investigated and found that the maximum resp...

  13. Superconductivity in the metal rich Li-Pd-B ternary boride.

    Science.gov (United States)

    Togano, K; Badica, P; Nakamori, Y; Orimo, S; Takeya, H; Hirata, K

    2004-12-10

    Superconductivity at about 8 K was observed in the metal-rich Li-Pd-B ternary system. Structural, microstructural, electrical, and magnetic investigations for various compositions proved that the Li2Pd3B compound, which has an antiperovskite cubic structure composed of distorted Pd6B octahedrons, is responsible for the superconductivity. This is the first observation of superconductivity in metal-rich ternary borides containing alkaline metal and Pd as a late transition metal. The compound prepared by arc melting has a high density and is relatively stable in the air. The upper critical fields H(c2)(0) estimated by linear extrapolation and the Werthamer-Helfand-Hohenberg theory are 6.2 and 4.8 T, respectively.

  14. Toxicogenomic responses of human alveolar epithelial cells to tungsten boride nanoparticles.

    Science.gov (United States)

    Türkez, Hasan; Arslan, Mehmet Enes; Sönmez, Erdal; Tatar, Abdulgani; Açikyildiz, Metin; Geyikoğlu, Fatime

    2017-08-01

    During the recent years, microarray analysis of gene expression has become an inevitable tool for exploring toxicity of drugs and other chemicals on biological systems. Therefore, toxicogenomics is considered as a fruitful area for searching cellular pathways and mechanisms including cancer, immunological diseases, environmental responses, gene-gene interactions and chemical toxicity. In this work, we examined toxic effects of Tungsten Borides NPs on gene expression profiling of the human lung alveolar epithelial cells (HPAEpiC). In line with this purpose, a single crystal of tungsten boride (mixture of WB and W2B) nanoparticles was synthesized by means of zone melting method, and characterized via using X-ray crystallography (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM) and energy-dispersive X-ray spectroscopy (EDX) techniques. Cell viability and cytotoxicity were determined by 3-(4,5-dimethyl-thiazol-2-yl) 2,5-diphenyltetrazolium bromide (MTT), neutral red (NR) and lactate dehydrogenase (LDH) release tests. The whole genome microarray expression analysis was performed to find out the effects of WB and W2B NPs mixture on gene expression of the HPAEpiC cell culture. 123 of 40,000 gene probes were assigned to characterize expression profile for WB/W2B NPs exposure. According to results; 70 genes were up-regulated and 53 genes were down-regulated (≥2 fold change). For further investigations, these genes were functionally classified by using DAVID (The Database for Annotation, Visualization and Integrated Discovery) with gene ontology (GO) analysis. In the light of the data gained from this study, it could be concluded that the mixture of WB/W2B NPs can affect cytokine/chemokine metabolism, angiogenesis and prevent migration/invasion by activating various genes. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. PREFACE: The 16th International Symposium on Boron, Borides and Related Materials (ISBB 2008)

    Science.gov (United States)

    Tanaka, Takaho

    2009-07-01

    This volume of Journal of Physics: Conference Series contains invited and contributed peer-reviewed papers that were presented at the 16th International Symposium on Boron, Borides and Related Materials (ISBB 2008), which was held on 7-12 September 2008, at Kunibiki Messe, Matsue, Japan. This triennial symposium has a half-century long history starting from the 1st meeting in 1959 at Asbury Park, New Jersey. We were very pleased to organize ISBB 2008, which gathered chemists, physicists, materials scientists as well as diamond and high-pressure researchers. This meeting had a strong background in the boron-related Japanese research history, which includes the discovery of superconductivity in MgB2 and development of Nd-Fe-B hard magnets and of YB66 soft X-ray monochromator. The scope of ISBB 2008 spans both basic and applied interdisciplinary research that is centered on boron, borides and related materials, and the collection of articles defines the state of the art in research on these materials. The topics are centered on: 1. Preparation of new materials (single crystals, thin films, nanostructures, ceramics, etc) under normal or extreme conditions. 2. Crystal structure and chemical bonding (new crystal structures, nonstoichiometry, defects, clusters, quantum-chemical calculations). 3. Physical and chemical properties (band structure, phonon spectra, superconductivity; optical, electrical, magnetic, emissive, mechanical properties; phase diagrams, thermodynamics, catalytic activity, etc) in a wide range of temperatures and pressures. 4. Applications and prospects (thermoelectric converters, composites, ceramics, coatings, etc) There were a few discoveries of new materials, such as nanomaterials, and developments in applications. Many contributions were related to 4f heavy Fermion systems of rare-earth borides. Exotic mechanisms of magnetism and Kondo effects have been discussed, which may indicate another direction of development of boride. Two special sessions

  16. Interlayer utilization (including metal borides) for subsequent deposition of NSD films via microwave plasma CVD on 316 and 440C stainless steels

    Science.gov (United States)

    Ballinger, Jared

    Diamond thin films have promising applications in numerous fields due to the extreme properties of diamonds in conjunction with the surface enhancement of thin films. Biomedical applications are numerous including temporary implants and various dental and surgical instruments. The unique combination of properties offered by nanostructured diamond films that make it such an attractive surface coating include extreme hardness, low obtainable surface roughness, excellent thermal conductivity, and chemical inertness. Regrettably, numerous problems exist when attempting to coat stainless steel with diamond generating a readily delaminated film: outward diffusion of iron to the surface, inward diffusion of carbon limiting necessary surface carbon precursor, and the mismatch between the coefficients of thermal expansion yielding substantial residual stress. While some exotic methods have been attempted to overcome these hindrances, the most common approach is the use of an intermediate layer between the stainless steel substrate and the diamond thin film. In this research, both 316 stainless steel disks and 440C stainless steel ball bearings were tested with interlayers including discrete coatings and graded, diffusion-based surface enhancements. Titanium nitride and thermochemical diffusion boride interlayers were both examined for their effectiveness at allowing for the growth of continuous and adherent diamond films. Titanium nitride interlayers were deposited by cathodic arc vacuum deposition on 440C bearings. Lower temperature diamond processing resulted in improved surface coverage after cooling, but ultimately, both continuity and adhesion of the nanostructured diamond films were unacceptable. The ability to grow quality diamond films on TiN interlayers is in agreement with previous work on iron and low alloy steel substrates, and the similarly seen inadequate adhesion strength is partially a consequence of the lacking establishment of an interfacial carbide phase

  17. Genetically Encoded FRET-Sensor Based on Terbium Chelate and Red Fluorescent Protein for Detection of Caspase-3 Activity

    Directory of Open Access Journals (Sweden)

    Alexander S. Goryashchenko

    2015-07-01

    Full Text Available This article describes the genetically encoded caspase-3 FRET-sensor based on the terbium-binding peptide, cleavable linker with caspase-3 recognition site, and red fluorescent protein TagRFP. The engineered construction performs two induction-resonance energy transfer processes: from tryptophan of the terbium-binding peptide to Tb3+ and from sensitized Tb3+ to acceptor—the chromophore of TagRFP. Long-lived terbium-sensitized emission (microseconds, pulse excitation source, and time-resolved detection were utilized to eliminate directly excited TagRFP fluorescence and background cellular autofluorescence, which lasts a fraction of nanosecond, and thus to improve sensitivity of analyses. Furthermore the technique facilitates selective detection of fluorescence, induced by uncleaved acceptor emission. For the first time it was shown that fluorescence resonance energy transfer between sensitized terbium and TagRFP in the engineered construction can be studied via detection of microsecond TagRFP fluorescence intensities. The lifetime and distance distribution between donor and acceptor were calculated using molecular dynamics simulation. Using this data, quantum yield of terbium ions with binding peptide was estimated.

  18. Corrosion Resistance of Nanopowders of Borides and Carbides of IV-VIB Group Metals in the Nickeling Electrolytes.

    Science.gov (United States)

    Shakhnin, Dmytro; Malyshev, Viktor; Kuschevskaya, Nina; Gab, Angelina

    2017-12-01

    The corrosion resistance of nanopowders of borides and carbides of metals of IV-VIB groups, as well as of silicon carbide, was studied in the standard nickeling electrolytes. As objects of study, nanopowders with the content of the main phase 91.8-97.6% and with the average particle size 32-78 nm were used. Their corrosion resistance was evaluated depending on the acidity of the electrolyte, temperature, and duration of the interaction. It was found that, by the corrosion resistance in the electrolytes solutions, nanopowders of borides and carbides within each group of compounds are similar and characterized by unlimited period of induction in alkaline media. An exception is the nanopowder of silicon carbide which is resistant to the solution of any acidity.

  19. Chemical modeling of mixed occupations and site preferences in anisotropic crystal structures: case of complex intermetallic borides.

    Science.gov (United States)

    Deringer, Volker L; Goerens, Christian; Esters, Marco; Dronskowski, Richard; Fokwa, Boniface P T

    2012-05-21

    Transition-metal borides show not only promising physical properties but also a rich variety of crystal structures. In this context, quantum-chemical tools can shed light on important facets of the chemistry within such intermetallic borides. Using density-functional theory (DFT), we analyze in detail two phases of significant structural-chemical importance: the recently synthesized Ti(1+x)Os(2-x)RuB(2) and the isotypical Ti(1+x)Os(3-x)B(2). Starting from the observation of different Ti/Os occupations in X-ray crystal structure analysis, we assess suitable computational models and rationalize how the interplay of Ti-Ti, Ti-Os, and Os-Os bonds drives the site preferences. Then, we move on to a systematic investigation of the metal-boron bonds which embed the characteristic, trigonal-planar B(4) units within their metallic surroundings. Remarkably, the different Ti-B bonds in Ti(1+x)Os(2-x)RuB(2) (and also in its ternary derivative) are of vastly different strength, and the strength of these bonds does not correlate with their length. The tools presented in this work are based on simple and insightful chemical arguments together with DFT, and may subsequently be transferred to other intermetallic phases--transition-metal borides and beyond.

  20. Green light emission in aluminum oxide powders doped with different terbium concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Mariscal B, L; Falcony, C. [IPN, Centro de Investigacion y de Estudios Avanzados, 07360 Ciudad de Mexico (Mexico); Carmona T, S.; Murrieta, H.; Sanchez A, M. A. [UNAM, Instituto de Fisica, 04510 Ciudad de Mexico (Mexico); Vazquez A, R. [IPN, Escuela Superior de Computo, 07738 Ciudad de Mexico (Mexico); Garcia R, C. M., E-mail: mariscal2005@gmail.com [UNAM, Facultad de Ciencias, 04510 Ciudad de Mexico (Mexico)

    2016-11-01

    Different emission intensities presented in aluminum oxide phosphors corresponding to different concentrations of doping performed with terbium are analyzed. The phosphors were synthesized by the evaporation technique and were characterized by photo and cathodoluminescence, X-ray diffraction and EDS techniques for different incorporation percentages of terbium as dopant; they show characteristic transitions in 494, 543, 587 and 622 nm, corresponding to {sup 5}D{sub 4} → {sup 7}F{sub 6}, {sup 5}D{sub 4} → {sup 7}F{sub 5}, {sup 5}D{sub 4} → {sup 7}F{sub 4} and {sup 5}D{sub 4} → {sup 7}F{sub 3}, respectively when they are excited with λ{sub exc} = 380 nm wavelength at room temperature. The results of X-ray diffraction show the presence of α-Al{sub 2}O{sub 3} phases with peaks located at 2θ = 25.78, 35.34, 37.96, 43.56, 45.8, 52.74, 57.7, 61.5, 66.74, 68.44, 77.12 and 80.94, and the δ-Al{sub 2}O-3 phase 2θ = 32.82, 45.8, 61.36 and 66.74. These compounds were heat treated for two hours at 1100 degrees Celsius. EDS analyzes indicate that these compounds have close to 60% oxygen around of 40% aluminum in the presence of terbium as dopant which indicates a stoichiometry close to the expected one for alumina. (Author)

  1. Graphene quantum dots-terbium ions as novel sensitive and selective time-resolved luminescent probes.

    Science.gov (United States)

    Llorent-Martínez, Eulogio J; Durán, Gema M; Ríos, Ángel; Ruiz-Medina, Antonio

    2018-01-01

    We propose an alternative approach for the development of analytical methods based on terbium-sensitized luminescence (TSL). TSL is based on the complexation between Tb(III) ions and fluorescent organic compounds that have appropriate functional groups to complex with Tb(III). We report the use of graphene quantum dot (GQDs) nanoparticles to improve the sensitivity and selectivity of TSL detection. GQDs can react with terbium ions through the carboxylic groups present in their structure. These Tb(III)-GQD complexes, formed in situ in aqueous solution, can be used as time-resolved luminescent probes. Ascorbic acid was selected as a target analyte to demonstrate the suitability of the proposed method. The selectivity of the TSL method was highly improved for most of the interferences tested. Under the optimum conditions [Tb(III) concentration 5 × 10-4 mol L-1, GQD concentration 4 mg L-1], a minimum 100% increase in selectivity was observed for several vitamins and common cations that may be present in the samples to be analyzed. In addition, the analytical signal showed a 30% enhancement with the use of GQDs compared with the use of merely Tb(III) ions, with a detection limit of 0.12 μg mL-1. The repeatability and intermediate precision were lower than 3% and 5%, respectively. From the results obtained, the implementation of GQDs in TSL can lead to the development of novel time-resolved luminescent probes with high analytical potential. Graphical abstract Quenching of Tb(III)-graphene quantum dot (GQD) luminescence by ascorbic acid (AA). TBL terbium-sensitized luminescence.

  2. Fluorescence study of some terbium-oligopeptide complexes in methanolic solution.

    Science.gov (United States)

    Rabouan, S; Delage, J; Durand, W; Prognon, P; Barthes, D

    2000-04-03

    This study concerned the use of lanthanide chelates to detect glycyl-leucyl-phenylalanine (GLF) and its homologues. Spectroscopic analysis of peptides without or with terbium complexation revealed the formation of (LF)(3)(Tb)(2), (GF)(3)(Tb)(2), (GLF)(3)(Tb)(2) and (FL)(4)Tb, (FG)(4)Tb complexes with high stability constants in methanolic solutions (pK(d)>13). Lanthanide chelate emission displayed a large Stokes shift (>270 nm), which allowed Tb chelates of GLF and its derivatives to be used for detection purposes. However, this preliminary study indicated some important limitations associated with lanthanide chelation, such as high methanolic content.

  3. Electromagnetic properties of terbium gallium garnet at millikelvin temperatures and low photon energy

    Science.gov (United States)

    Kostylev, Nikita; Goryachev, Maxim; Bushev, Pavel; Tobar, Michael E.

    2017-07-01

    Electromagnetic properties of single crystal terbium gallium garnet are characterised from room down to millikelvin temperatures using the whispering gallery mode method. Microwave spectroscopy is performed at low powers equivalent to a few photons in energy and conducted as functions of the magnetic field and temperature. A phase transition is detected close to the temperature of 3.5 K. This is observed for multiple whispering gallery modes causing an abrupt negative frequency shift and a change in transmission due to extra losses in the new phase caused by a change in complex magnetic susceptibility.

  4. Nuclear excitation functions from 40 to 200 MeV proton irradiation of terbium

    Energy Technology Data Exchange (ETDEWEB)

    Engle, Jonathan W., E-mail: jwengle@lanl.gov; Mashnik, Stepan G.; Parker, Lauren A.; Jackman, Kevin R.; Bitteker, Leo J.; Ullmann, John L.; Gulley, Mark S.; Pillai, Chandra; John, Kevin D.; Birnbaum, Eva R.; Nortier, Francois M.

    2016-01-01

    Nuclear formation cross sections are reported for 26 radionuclides, measured with 40–200 MeV proton irradiations of terbium foils. These data provide the basis for the production of medically relevant radionuclides (e.g., {sup 152}Tb, {sup 155}Tb, {sup 155}Eu, and {sup 156}Eu) and {sup 153}Gd, a potential source used in ongoing efforts to characterize stellar nucleosynthesis routes. Computational predictions from the ALICE2011, CEM03.03, Bertini, and INCL + ABLA codes are compared with newly measured data to contribute to the ongoing process of code development, and yields are calculated for selected radionuclides using measured data.

  5. The structure and hardness of the highest boride of tungsten, a borophene-based compound.

    Science.gov (United States)

    Gonzalez Szwacki, Nevill

    2017-06-22

    Two-dimensional systems have strengthened their position as a key materials for novel applications. Very recently, boron joined the distinguished group of elements confirmed to possess 2D allotropes, named borophenes. In this work, we explore the stability and hardness of the highest borides of tungsten, which are built of borophenes separated by metal atoms. We show that the WB3+x compounds have Vickers hardnesses approaching 40 GPa only for small values of x. The insertion of extra boron atoms is, in general, detrimental to the hardness of WB3 because it leads to the formation of quasi-planar boron sheets that are less tightly connected with the adjacent tungsten layers. Very high concentrations of boron (x ≈ 1), give rise to a soft (Vickers hardness of ~8 GPa) and unstable hP20-WB4 structure that can be considered to be built of quasi-planar boron α-sheets separated by graphitic tungsten layers. By contrast, we show that the formation of tungsten vacancies leads to structures, e.g. W0.75B3+x , with Vickers hardnesses that are not only similar in value to the experimentally reported load-independent hardnesses greater than 20 GPa, but are also less sensitive to variations in the boron content.

  6. Micelle-enhanced and terbium-sensitized spectrofluorimetric determination of gatifloxacin and its interaction mechanism

    Science.gov (United States)

    Guo, Changchuan; Wang, Lei; Hou, Zhun; Jiang, Wei; Sang, Lihong

    2009-05-01

    A terbium-sensitized spectrofluorimetric method using an anionic surfactant, sodium dodecyl benzene sulfonate (SDBS), was developed for the determination of gatifloxacin (GFLX). A coordination complex system of GFLX-Tb 3+-SDBS was studied. It was found that SDBS significantly enhanced the fluorescence intensity of the complex (about 11-fold). Optimal experimental conditions were determined as follows: excitation and emission wavelengths of 331 and 547 nm, pH 7.0, 2.0 × 10 -4 mol l -1 terbium (III), and 2.0 × 10 -4 mol l -1 SDBS. The enhanced fluorescence intensity of the system (Δ If) showed a good linear relationship with the concentration of GFLX over the range of 5.0 × 10 -10 to 5.0 × 10 -8 mol l -1 with a correlation coefficient of 0.9996. The detection limit (3 σ) was determined as 6.0 × 10 -11 mol l -1. This method has been successfully applied to the determination of GFLX in pharmaceuticals and human urine/serum samples. Compared with most of other methods reported, the rapid and simple procedure proposed in the text offers higher sensitivity, wider linear range, and better stability. The interaction mechanism of the system is also studied by the research of ultraviolet absorption spectra, surface tension, solution polarity and fluorescence polarization.

  7. Circularly Polarized Luminescence in Enantiopure Europium and Terbium Complexes with Modular, All-Oxygen Donor Ligands

    Science.gov (United States)

    Seitz, Michael; Do, King; Ingram, Andrew J.; Moore, Evan G.; Muller, Gilles; Raymond, Kenneth N.

    2009-01-01

    Abstract: Circulaly polarized luminescence from terbium(III) complexed and excited by chiral antenna ligands gives strong emission The modular synthesis of three new octadentate, enantiopure ligands are reported - one with the bidentate chelating unit 2-hydroxyisophthalamide (IAM) and two with 1-hydroxy-2-pyridinone (1,2-HOPO) units. A new design principle is introduced for the chiral, non-racemic hexamines which constitute the central backbones for the presented class of ligands. The terbium(III) complex of the IAM ligand, as well as the europium(III) complexes of the 1,2-HOPO ligands are synthesized and characterized by various techniques (NMR, UV, CD, luminescence spectroscopy). All species exhibit excellent stability and moderate to high luminescence efficiency (quantum yields ΦEu = 0.05–0.08 and ΦTb = 0.30–0.57) in aqueous solution at physiological pH. Special focus is put onto the properties of the complexes in regard to circularly polarized luminescence (CPL). The maximum luminescence dissymmetry factors (glum) in aqueous solution are high with |glum|max = 0.08 – 0.40. Together with the very favorable general properties (good stability, high quantum yields, long lifetimes), the presented lanthanide complexes can be considered as good candidates for analytical probes based on CPL in biologically relevant environments. PMID:19639983

  8. Synthesis of Binary Transition Metal Nitrides, Carbides and Borides from the Elements in the Laser-Heated Diamond Anvil Cell and Their Structure-Property Relations

    Science.gov (United States)

    Friedrich, Alexandra; Winkler, Björn; Juarez-Arellano, Erick A.; Bayarjargal, Lkhamsuren

    2011-01-01

    Transition metal nitrides, carbides and borides have a high potential for industrial applications as they not only have a high melting point but are generally harder and less compressible than the pure metals. Here we summarize recent advances in the synthesis of binary transition metal nitrides, carbides and borides focusing on the reaction of the elements at extreme conditions generated within the laser-heated diamond anvil cell. The current knowledge of their structures and high-pressure properties like high-(p,T) stability, compressibility and hardness is described as obtained from experiments. PMID:28824101

  9. Synthesis of Binary Transition Metal Nitrides, Carbides and Borides from the Elements in the Laser-Heated Diamond Anvil Cell and Their Structure-Property Relations

    Directory of Open Access Journals (Sweden)

    Lkhamsuren Bayarjargal

    2011-09-01

    Full Text Available Transition metal nitrides, carbides and borides have a high potential for industrial applications as they not only have a high melting point but are generally harder and less compressible than the pure metals. Here we summarize recent advances in the synthesis of binary transition metal nitrides, carbides and borides focusing on the reaction of the elements at extreme conditions generated within the laser-heated diamond anvil cell. The current knowledge of their structures and high-pressure properties like high-(p; T stability, compressibility and hardness is described as obtained from experiments.

  10. Computational-Experimental Processing of Boride/Carbide Composites by Reactive Infusion of Hf Alloy Melts into B4C

    Science.gov (United States)

    2015-09-16

    PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) UNIVERSITY OF TEXAS AT EL PASO 500 UNIV ST ADMIN BLDG 209 EL PASO, TX 79968-0001 US 8. PERFORMING...Arturo Bronson UNIVERSITY OF TEXAS AT EL PASO Final Report 09/16/2015 DISTRIBUTION A: Distribution approved for public release. AF Office Of Scientific...University of Texas at El Paso July 2015 Bronson-Kumar (University of Texas at El Paso) 1 Computational-Experimental Processing of Boride/Carbide Composites

  11. Novel class of heterometallic cubane and boride clusters containing heavier group 16 elements.

    Science.gov (United States)

    Thakur, Arunabha; Sao, Soumik; Ramkumar, V; Ghosh, Sundargopal

    2012-08-06

    Thermolysis of an in situ generated intermediate, produced from the reaction of [Cp*MoCl(4)] (Cp* = η(5)-C(5)Me(5)) and [LiBH(4).THF], with excess Te powder yielded isomeric [(Cp*Mo)(2)B(4)TeH(5)Cl] (2 and 3), [(Cp*Mo)(2)B(4)(μ(3)-OEt)TeH(3)Cl] (4), and [(Cp*Mo)(4)B(4)H(4)(μ(4)-BH)(3)] (5). Cluster 4 is a notable example of a dimolybdaoxatelluraborane cluster where both oxygen and tellurium are contiguously bound to molybdenum and boron. Cluster 5 represents an unprecedented metal-rich metallaborane cluster with a cubane core. The dimolybdaheteroborane 2 was found to be very reactive toward metal carbonyl compounds, and as a result, mild pyrolysis of 2 with [Fe(2)(CO)(9)] yielded distorted cubane cluster [(Cp*Mo)(2)(BH)(4)(μ(3)-Te){Fe(CO)(3)}] (6) and with [Co(2)(CO)(8)] produced the bicapped pentagonal bipyramid [(Cp*MoCo)(2)B(3)H(2)(μ(3)-Te)(μ-CO){Co(3)(CO)(6)}] (7) and pentacapped trigonal prism [(Cp*MoCo)(2)B(3)H(2)(μ(3)-Te)(μ-CO)(4){Co(6)(CO)(8)}] (8). The geometry of 8 is an example of a heterometallic boride cluster in which five Co and one Mo atom define a trigonal prismatic framework. The resultant trigonal prism core is in turn capped by two boron, one Te, and one Co atom. In the pentacapped trigonal prism unit of 8, one of the boron atoms is completely encapsulated and bonded to one molybdenum, one boron, and five cobalt atoms. All the new compounds have been characterized in solution by IR, (1)H, (11)B, and (13)C NMR spectroscopy, and the structural types were unambiguously established by crystallographic analysis of 2 and 4-8.

  12. Luminescent method of determination of composition of europium and terbium complexes in solution by change of intensity ratio of luminescence bands

    Energy Technology Data Exchange (ETDEWEB)

    Bel' tyukova, S.V.; Nazarenko, N.A.; Poluehktov, N.S.

    1982-03-01

    The complexes of europium and terbium with phenanthroline, ethylenediaminetetraacetate, nitrilotriacetate, some acids-phenol derivatives and ..beta..-diketones series have been used as an example to demonstrate that the value of the ratio of intensities on the two bands of europium(terbium) luminescence spectra - the one corresponding to the hypersensitive'' transition and the other, to the magnetic dipole one - can be used for determination of the complexes composition in solutions.

  13. Microstructural evaluation of a low carbon steel submitted to boriding treatment pre and post GTAW welding; Avaliacao microestrutural de um aco de baixo carbono submetido ao tratamento de boretacao pre e pos-soldagem GTAW

    Energy Technology Data Exchange (ETDEWEB)

    Pollnow, Edilson Nunes; Osorio, Alice Goncalves, E-mail: edilson.pollnow@hotmail.com, E-mail: osorio.alice@gmail.com [Universidade Federal de Pelotas (CDTec/UFPel), Pelotas, RS (Brazil). Centro de Desenvolvimento Tecnologico; Araujo, Douglas Bezerra de, E-mail: dbaraujo@ufu.br [Universidade Federal de Uberlandia (FEMEC/UFU), Uberlandia, MG (Brazil). Faculdade de Engenharia Mecanica; Passos, Thais Andrezza dos; Souza, Daniel, E-mail: thais.andrezza.passos@gmail.com, E-mail: danielsouza@furg.br [Universidade Federal do Rio Grande (EE/FURG), Rio Grande, RS (Brazil). Escola de Engenharia

    2017-04-15

    Studies on surface engineering area are given great importance due to the improvement that surface modifications provide to materials. With a global market that has the need to provide parts and equipment with extended service life and low cost, to support stringent requests and thus maintain its high performance, surface treatments may bring what was impossible into reality. Among the surface treatments that have received attention recently, we have the thermochemical process of boriding. The boriding process consists of saturate the surface of steels and metal alloys with boron. This saturation provides an increase in the surface properties not inherent to the base metal, such as hardness, resistance to abrasion and corrosion. Although the properties of boriding steels have already been studied, the effects that the boriding process perform on the steel during or after the welding processes are not known. Hence, it is the purpose of this study to evaluate the microstructure of a low carbon steel treated with boriding before and after GTAW welding. The results indicated poor metallurgical weldability of low carbon steel with boride layer, with the presence of solidification cracks. Nonetheless, the steel welded previous to boring treatment presented a more ductile nucleus, with harder surface. Although the values of hardness within the nucleus of the steel had dropped drastically at the welded zone after the boring, the surface of this steel showed higher values of hardness due to the boriding layer. This fact should be considered when applications where wear resistance is needed. (author)

  14. Kinetics of electrolysis current reversal boriding of tool steels in a boron-containing oxychloride melt based on CaCl2

    Science.gov (United States)

    Chernov, Ya. B.; Filatov, E. S.

    2017-08-01

    The kinetics of thermal diffusion boriding in a melt based on calcium chloride with a boron oxide additive is studied using reversed current. The main temperature, concentration, and current parameters of the process are determined. The phase composition of the coating is determined by a metallographic method.

  15. Thermo-transferred thermoluminescence (TTTl) in potassium-yttrium double fluoride doped with terbium

    Energy Technology Data Exchange (ETDEWEB)

    Gallegos, A.; Rivera, T.; Diaz G, J. A. [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Legaria 694, Col. Irrigacion, 11500 Mexico D. F. (Mexico); Azorin, J. [Universidad Autonoma Metropolitana, Unidad Iztapalapa, San Rafael Atlixco No. 186, Col. Vicentina, 09340 Mexico D. F. (Mexico); Azorin, J. C. [Universidad de Guanajuato, Division de Ciencias e Ingenierias-Campus Leon, Lomas del Bosque No. 103, Col. Lomas del Campestre, 37000 Leon, Guanajuato (Mexico); Licona, R.; Rivas, F.; Hernandez C, G. [Benemerita Universidad Autonoma de Puebla, Facultad de Ciencias Quimicas, 14 Sur y San Claudio, Ciudad Universitaria, Puebla de Zaragoza, Puebla (Mexico); Khaidukov, N. [Institute of General and Inorganic Chemistry, Lenin SK 11 Prospect 31, Moscow 117907 (Russian Federation)

    2011-02-15

    This paper presents results of studying the thermo-transferred thermoluminescence (TTTl) phenomenon in potassium-yttrium double fluoride doped with terbium (K{sub 2}YF{sub 5:}Tb) at different impurity concentrations (0.8%, 0.95% and 0.99%). Previously to study the TTTl phenomenon, structural characterization and chemical composition of the materials were determined. The structural studies were conducted using a scanning electron microscope; meanwhile, chemical composition was analyzed using energy dispersive X-ray spectroscopy. Thermoluminescence kinetics was studied irradiating the samples with {sup 137}Cs gamma rays as well as with {sup 90}Sr/{sup 90}Y beta rays, analyzing the glow curves by the deconvolution method for obtaining the kinetic parameters. (Author)

  16. The influence of pressure on the photoluminescence properties of a terbium-adipate framework

    Science.gov (United States)

    Spencer, Elinor C.; Zhao, Jing; Ross, Nancy L.; Andrews, Michael B.; Surbella, Robert G.; Cahill, Christopher L.

    2013-06-01

    The influence of pressure (over the 0-4.7 GPa range) on the photoluminescence emissions and crystal structure of the known 3D terbium-adipate metal-organic framework material Tb-GWMOF6 has been evaluated by high-pressure single-crystal X-ray diffraction and spectroscopic techniques. The results from this study show that this complex lanthanide framework structure undergoes three phase transitions within the 0-4 GPa pressure range that involve alterations in the number of symmetry independent Tb3+ ion sites within the crystal lattice. These pressure induced modifications to the structure of Tb-GWMOF6 lead to pronounced changes in the profiles of the 5D4→7F5 emission spectra of this complex.

  17. Terbium Radionuclides for Theranostics Applications: A Focus On MEDICIS-PROMED

    Science.gov (United States)

    Cavaier, R. Formento; Haddad, F.; Sounalet, T.; Stora, T.; Zahi, I.

    A new facility, named CERN-MEDICIS, is under construction at CERN to produce radionuclides for medical applications. In parallel, the MEDICIS-PROMED, a Marie Sklodowska-Curie innovative training network of the Horizon 2020 European Commission's program, is being coordinated by CERN to train young scientists on the production and use of innovative radionuclides and develop a network of experts within Europe. One program within MEDICIS-PROMED is to determine the feasibility of producing innovative radioisotopes for theranostics using a commercial middle-sized high-current cyclotron and the mass separation technology developed at CERN-MEDICIS. This will allow the production of high specific activity radioisotopes not achievable with the common post-processing by chemical separation. Radioisotopes of scandium, copper, arsenic and terbium have been identified. Preliminary studies of activation yield and irradiation parameters optimization for the production of Tb-149 will be described.

  18. Dielectric and conducting behavior of gadolinium-terbium fumarate heptahydrate crystals

    Science.gov (United States)

    Shah, M. D.; Want, B.

    2015-07-01

    Gadolinium-terbium fumarate heptahydrate crystals were grown in silica gel by using single gel diffusion technique. The crystals were characterized by different physico-chemical techniques of characterization. Powder X-ray diffraction results showed that the grown material is purely crystalline in nature. Elemental analyses suggested the chemical formula of the compound to be Gd Tb (C4H2O4)3ṡ7H2O. Energy dispersive X-ray analysis confirmed the presence of Gd and Tb in the title compound. The dielectric and conductivity studies of the grown compound were carried as function of frequency of applied field and the temperature. The grown material showed a dielectric anomaly which was correlated with its thermal behavior. The ac conductivity of the material showed Jonscher's power law behavior: σ(ω)=σo+Aωs, with a temperature-dependent power exponent s(<1). The conductivity was found to be a function of temperature and frequency.

  19. Highly sensitive detection of dipicolinic acid with a water-dispersible terbium-metal organic framework.

    Science.gov (United States)

    Bhardwaj, Neha; Bhardwaj, Sanjeev; Mehta, Jyotsana; Kim, Ki-Hyun; Deep, Akash

    2016-12-15

    The sensitive detection of dipicolinic acid (DPA) is strongly associated with the sensing of bacterial organisms in food and many types of environmental samples. To date, the demand for a sensitive detection method for bacterial toxicity has increased remarkably. Herein, we investigated the DPA detection potential of a water-dispersible terbium-metal organic framework (Tb-MOF) based on the fluorescence quenching mechanism. The Tb-MOF showed a highly sensitive ability to detect DPA at a limit of detection of 0.04nM (linear range of detection: 1nM to 5µM) and also offered enhanced selectivity from other commonly associated organic molecules. The present study provides a basis for the application of Tb-MOF for direct, convenient, highly sensitive, and specific detection of DPA in the actual samples. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. A New Bis(phthalocyaninato) Terbium Single-Ion Magnet with an Overall Excellent Magnetic Performance.

    Science.gov (United States)

    Chen, Yuxiang; Ma, Fang; Chen, Xiaoxiang; Dong, Bowei; Wang, Kang; Jiang, Shangda; Wang, Chiming; Chen, Xin; Qi, Dongdong; Sun, Haoling; Wang, Bingwu; Gao, Song; Jiang, Jianzhuang

    2017-11-20

    Bulky and strong electron-donating dibutylamino groups were incorporated onto the peripheral positions of one of the two phthalocyanine ligands in the bis(phthalocyaninato) terbium complex, resulting in the isolation of heteroleptic double-decker (Pc)Tb{Pc[N(C4H9)2]8} {Pc = phthalocyaninate; Pc[N(C4H9)2]8 = 2,3,9,10,16,17,23,24-octakis(dibutylamino)phthalocyaninate} with the nature of an unsymmetrical molecular structure, a square-antiprismatic coordination geometry, an intensified coordination field strength, and the presence of organic radical-f interaction. As a total result of all these factors, this sandwich-type tetrapyrrole lanthanide single-ion magnet (SIM) exhibits an overall enhanced magnetic performance including a high blocking temperature (TB) of 30 K and large effective spin-reversal energy barrier of Ueff = 939 K, rendering it the best sandwich-type tetrapyrrole lanthanide SIM reported thus far.

  1. Ultralarge magneto-optic rotations and rotary dispersion in terbium gallium garnet single crystal.

    Science.gov (United States)

    Shaheen, Amrozia; Majeed, Hassaan; Anwar, Muhammad Sabieh

    2015-06-10

    We report systematically acquired data on the Verdet constant of terbium gallium garnet for wavelengths ranging from visible to near-infrared (405-830 nm) regime. Our experimental method of Stokes polarimetry is based on the Fourier decomposition of the received light intensity and allows unambiguous determination of both the Faraday rotation and the ellipticity of the emergent light. Temperature-dependent investigations in the range of 8-300 K extend earlier reports and verify the Verdet's constant direct dependence on the magnetization, whose first-order approximation is simply a manifestation of the Curie's law. Further, a least-squares fitting of the experimental data correlates well with theoretical predictions. At a wavelength of 405 nm and temperature of 8 K, the rotation is approximately 500°.

  2. Terbium fluorescence as a sensitive, inexpensive probe for UV-induced damage in nucleic acids

    Energy Technology Data Exchange (ETDEWEB)

    El-Yazbi, Amira F.; Loppnow, Glen R., E-mail: glen.loppnow@ualberta.ca

    2013-07-05

    Graphical abstract: -- Highlights: •Simple, inexpensive, mix-and-read assay for positive detection of DNA damage. •Recognition of undamaged DNA via hybridization to a hairpin probe. •Terbium(III) fluorescence reports the amount of damage by binding to ssDNA. •Tb/hairpin is a highly selective and sensitive fluorescent probe for DNA damage. -- Abstract: Much effort has been focused on developing methods for detecting damaged nucleic acids. However, almost all of the proposed methods consist of multi-step procedures, are limited, require expensive instruments, or suffer from a high level of interferences. In this paper, we present a novel simple, inexpensive, mix-and-read assay that is generally applicable to nucleic acid damage and uses the enhanced luminescence due to energy transfer from nucleic acids to terbium(III) (Tb{sup 3+}). Single-stranded oligonucleotides greatly enhance the Tb{sup 3+} emission, but duplex DNA does not. With the use of a DNA hairpin probe complementary to the oligonucleotide of interest, the Tb{sup 3+}/hairpin probe is applied to detect ultraviolet (UV)-induced DNA damage. The hairpin probe hybridizes only with the undamaged DNA. However, the damaged DNA remains single-stranded and enhances the intrinsic fluorescence of Tb{sup 3+}, producing a detectable signal directly proportional to the amount of DNA damage. This allows the Tb{sup 3+}/hairpin probe to be used for sensitive quantification of UV-induced DNA damage. The Tb{sup 3+}/hairpin probe showed superior selectivity to DNA damage compared to conventional molecular beacons probes (MBs) and its sensitivity is more than 2.5 times higher than MBs with a limit of detection of 4.36 ± 1.2 nM. In addition, this probe is easier to synthesize and more than eight times cheaper than MBs, which makes its use recommended for high-throughput, quantitative analysis of DNA damage.

  3. Fine- and hyperfine structure investigations of even configuration system of atomic terbium

    Science.gov (United States)

    Stefanska, D.; Elantkowska, M.; Ruczkowski, J.; Furmann, B.

    2017-03-01

    In this work a parametric study of the fine structure (fs) and the hyperfine structure (hfs) for the even-parity configurations of atomic terbium (Tb I) is presented, based in considerable part on the new experimental results. Measurements on 134 spectral lines were performed by laser induced fluorescence (LIF) in a hollow cathode discharge lamp; on this basis, the hyperfine structure constants A and B were determined for 52 even-parity levels belonging to the configurations 4f85d6s2, 4f85d26s or 4f96s6p; in all the cases those levels were involved in the transitions investigated as the lower levels. For 40 levels the hfs was examined for the first time, and for the remaining 12 levels the new measurements supplement our earlier results. As a by-product, also preliminary values of the hfs constants for 84 odd-parity levels were determined (the investigations of the odd-parity levels system in the terbium atom are still in progress). This huge amount of new experimental data, supplemented by our earlier published results, were considered for the fine and hyperfine structure analysis. A multi-configuration fit of 7 configurations was performed, taking into account second-order of perturbation theory, including the effects of closed shell-open shell excitations. Predicted values of the level energies, as well as of magnetic dipole and electric quadrupole hyperfine structure constants A and B, are quoted in cases when no experimental values are available. By combining our experimental data with our own semi-empirical procedure it was possible to identify correctly the lower and upper level of the line 544.1440 nm measured by Childs with the use of the atomic-beam laser-rf double-resonance technique (Childs, J Opt Soc Am B 9;1992:191-6).

  4. High-pressure study on borides, nanocrystals and negative thermal expansion materials

    Science.gov (United States)

    Chen, Bin

    2001-07-01

    By the use of Mao-Bell diamond anvil cell, employed with x-ray diffraction, optical absorption, Raman and Fourier Transform Infrared (FTIR) spectroscopy, iron borides, nanocrystalline Ni, Fe, Ni3Fe, Al2O 3, Negative Thermal Expansion (NTE) materials such as HfW2O 8, ZrW2O8, ZrMo2O8 have been studied under high pressure. The results of a synchrotron x-ray diffraction study of Fe2B under quasi-hydrostatic conditions from 0 to 50 GPa are reported. Over this pressure range, no phase change or disproportionation has been observed. A value of the bulk modulus, K, of 192 +/- 14 GPa and the first pressure derivative of the bulk modulus, K', of 2.6 +/- 0.6, are obtained. The compression is found to be anisotropic, with the a-axis being more incompressible than the c-axis. X-ray diffraction data of nanocrystalline Ni, Fe and Ni3Fe, using a synchrotron source, was collected under nonhydrostatic and quasi-hydrostatic conditions up to 60 GPa. The bulk moduli, of 185.4 +/- 10 GPa, 171 +/- 5 GPa, 179.4 +/- 8.1 GPa, 168.3 +/- 2.6 GPa, are determined from quasi-hydrostatic compression data of nanocrystalline Ni, alpha-Fe, epsilon-Fe and Ni3Fe, respectively, which are found similar to those of large-grained counterparts. Their phase transformations are studied and compared with their bulk counterparts. A new phase of Al2O3 formed by compression of the nanocrystalline gamma-phase has been detected. This high-pressure phase is metastable upon decompression to ambient pressure, and has a bulk modulus of 251 +/- 10 GPa for Al2O3 of 67 nm. From hydrostatic compression, bulk moduli of K67 = 238 +/- 3 GPa and K37 = 172 +/- 3 GPa are obtained for the 67 nm and 37 nm gamma-Al2O3 particles, respectively, which are significantly higher than that found in a previous study of smaller sized nanocrystals of gamma-alumina (K20 = 162 +/- 14 GPa for 20 nm crystallites). High pressure optical absorption, Raman and FTIR measurements are carried out on negative thermal expansion materials: HfW2O8, ZrW2O

  5. Structural and optical characterization of terbium doped ZnGa2O4 thin films deposited by RF magnetron sputtering

    Science.gov (United States)

    Somasundaram, K.; Girija, K. G.; Sudarsan, V.; Selvin, P. Christopher; Vatsa, R. K.

    2016-05-01

    Tb3+ doped ZnGa2O4 nanophosphor (21 nm) has been synthesized via low temperature polyol route and subsequently thin films of the same were deposited on glass and ITO substrates by RF magnetron sputtering. The films were characterized by X-ray Diffraction and luminescence measurements. The XRD pattern showed that Tb3+ doped ZnGa2O4 nanophosphor has a cubic spinel phase. Luminescence behavior of the nanophosphor and as deposited sputtered film was investigated. The PL emission spectra of nanophosphor gave a broad ZnGa2O4 host emission band along with a strong terbium emission and the thin films showed only broad host emission band and there was no terbium ion emission.

  6. Determination of fluoxetine in pharmaceutical and biological samples based on the silver nanoparticle enhanced fluorescence of fluoxetine-terbium complex.

    Science.gov (United States)

    Lotfi, Ali; Manzoori, Jamshid L

    2016-11-01

    In this study, a simple and sensitive spectrofluorimetric method is presented for the determination of fluoxetine based on the enhancing effect of silver nanoparticles (AgNPs) on the terbium-fluoxetine fluorescence emission. The AgNPs were prepared by a simple reduction method and characterized by UV-Vis spectroscopy and transmission electron microscopy. It was indicated that these AgNPs have a remarkable amplifying effect on the terbium-sensitized fluorescence of fluoxetine. The effects of various parameters such as AgNP and Tb(3+) concentration and the pH of the media were investigated. Under obtained optimal conditions, the fluorescence intensity of the terbium-fluoxetine-AgNP system was enhanced linearly by increasing the concentration of fluoxetine in the range of 0.008 to 19 mg/L. The limit of detection (b + 3s) was 8.3 × 10(-4) mg/L. The interference effects of common species found in real samples were also studied. The method had good linearity, recovery, reproducibility and sensitivity, and was satisfactorily applied for the determination of fluoxetine in tablet formulations, human urine and plasma samples. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  7. Neutron Diffraction and Electrical Transport Studies on Magnetic Transition in Terbium at High Pressures and Low Temperatures

    Science.gov (United States)

    Thomas, Sarah; Montgomery, Jeffrey; Tsoi, Georgiy; Vohra, Yogesh; Weir, Samuel; Tulk, Christopher; Moreira Dos Santos, Antonio

    2013-06-01

    Neutron diffraction and electrical transport measurements have been carried out on the heavy rare earth metal terbium at high pressures and low temperatures in order to elucidate its transition from a helical antiferromagnetic to a ferromagnetic ordered phase as a function of pressure. The electrical resistance measurements using designer diamonds show a change in slope as the temperature is lowered through the ferromagnetic Curie temperature. The temperature of the ferromagnetic transition decreases at a rate of -16.7 K/GPa till 3.6 GPa, where terbium undergoes a structural transition from hexagonal close packed (hcp) to an α-Sm phase. Above this pressure, the electrical resistance measurements no longer exhibit a change in slope. In order to confirm the change in magnetic phase suggested by the electrical resistance measurements, neutron diffraction measurements were conducted at the SNAP beamline at the Oak Ridge National Laboratory. Measurements were made at pressures to 5.3 GPa and temperatures as low as 90 K. An abrupt increase in peak intensity in the neutron diffraction spectra signaled the onset of magnetic order below the Curie temperature. A magnetic phase diagram of rare earth metal terbium will be presented to 5.3 GPa and 90 K based on these studies.

  8. Thermodynamic modelling of phase equilibrium in system Ti-B-Si-C, synthesis and phases composition of borides and carbides layers on titanic alloyVT-1 at electron beam treatment in vacuum

    Science.gov (United States)

    Smirnyagina, N. N.; Khaltanova, V. M.; Lapina, A. E.; Dasheev, D. E.

    2017-01-01

    Composite layers on the basis of carbides and borides the titan and silicon on titanic alloy VT-1 are generated at diffused saturation in vacuum. Formation in a composite of MAX phase Ti3SiC2 is shown. Thermodynamic research of phase equilibrium in systems Ti-Si-C and Ti-B-C in the conditions of high vacuum is executed. The thermodynamics, formation mechanisms of superfirm layers borides and carbides of the titan and silicon are investigated.

  9. Synthesis, characterization and investigation of thermoelectric properties of selected metal borides; Synthese, Charakterisierung und Untersuchung thermoelektrischer Eigenschaften ausgewaehlter Metallboride

    Energy Technology Data Exchange (ETDEWEB)

    Stober, Frederick

    2012-06-04

    The present work deals with the high-temperature thermoelectric properties of transition metal [eg V, Cr, Mn, Ni, Cu] and lanthanide [e.g. Sc, Y, Gd, Er, Dy]-borides. In particular, intercalation compounds of beta-rhombohedral boron, compounds of the type MB{sub 66}, dodecaborides and hexaborides were examined. In the case of intercalation compounds of beta-rhombohedral boron it was found that the incorporation of metals such as Sc, Mn or Cu result in favorable thermoelectric properties. The reason is most likely the preferred occupation of the metal position M2 instead of M4. Composites, for example, DyB{sub 66}-DyB{sub 12} show high electrical conductivities, high Seebeck effects at high temperatures due to the presence of DyB{sub 12} and low thermal conductivities as a result of the DyB{sub 66} matrix. At 1100K the composite DyB{sub 66}-DyB{sub 12} shows a ZT value of 0.55, thus exceeding the ZT of boron carbide (B{sub 13}C{sub 2}) at this temperature which is considered the best p-type boride material. A composite of ErB{sub 12}-ErB{sub 4}-ErB{sub 2} has negative Seebeck coefficients and shows a ZT value of 0.5 at 840K. Furthermore, the structure of tetragonal Scandiumdodecaboride ScB{sub 12} was solved on the basis of synchrotron data from a crystalline powder, after it has been debated for decades but never fully resolved.

  10. Study of Silver Nanoparticles Sensitized Fluorescence and Second-Order Scattering of Terbium(III-Pefloxacin Mesylate Complex and Determination of Pefloxacin Mesylate

    Directory of Open Access Journals (Sweden)

    Aiyun Li

    2014-01-01

    Full Text Available α-Keto acid of pefloxacin mesylate (PFLX can form the complex with Terbium(III. The intramolecular energy from PFLX to Terbium(III ion takes place when excited, and thus Terbium(III excited state is formed and then emits the characteristic fluorescence of Terbium(III, locating at 490, 545, 580, and 620 nm. The second-order scattering (SOS peak at 545 nm also appears for the complex with the exciting wavelength of 273 nm. When the silver nanoparticles are added to the system, the luminescence intensity at 545 nm greatly increased. So, with the adding of nanoparticles to the Terbium(III-PFLX complex, not only is the intramolecular energy promoted but also the SOS intensity is enhanced. The experimental results show that it is the silver nanoparticles with certain size and certain concentration which can greatly enhance the fluorescence-SOS intensity, and the relative intensity at 545 nm is proportional to the amount of PFLX. Based on this phenomenon, a novel method for the determination of PFLX has been developed and applied to the determination of PFLX in capsule and serum samples.

  11. Influence of crystalline structure on the luminescence properties of terbium orthotantalates

    Energy Technology Data Exchange (ETDEWEB)

    Siqueira, Kisla P.F. [Departamento de Química, Universidade Federal de Ouro Preto, Campus Morro do Cruzeiro, ICEB II, Ouro Preto 35400-000, Minas Gerais (Brazil); Carmo, Alexandre P. [Instituto Federal Fluminense, Campus Cabo Frio, RJ 28909-971 (Brazil); Bell, Maria J.V. [Departamento de Física, Universidade Federal de Juiz de Fora, Juiz de Fora 36036-330, MG (Brazil); Dias, Anderson, E-mail: anderson_dias@iceb.ufop.br [Departamento de Química, Universidade Federal de Ouro Preto, Campus Morro do Cruzeiro, ICEB II, Ouro Preto 35400-000, Minas Gerais (Brazil)

    2013-06-15

    Terbium orthotantalate powders were produced with M-fergusonite type (I2/a) and M′-fergusonite type (P2/a) structures. The samples were studied by X-ray diffraction, Raman scattering, and photoluminescence measurements (emission and decay curves). The results showed that crystalline materials were obtained with all the 18 Raman-active modes predicted by group theory calculations. Also, it was observed through photoluminescence decay curves that the Tb{sup 3+} ions occupies only one-symmetry site in both crystallographic arrangements. Photoluminescence emission curves exhibited some variation in spectral shape, peak position, and relative intensity as a consequence of their different crystalline arrangements. The dominated emission of Tb{sup 3+} ({sup 5}D{sub 4}→{sup 7}F{sub 5}) is centered with a maximum intensity at 549.2 nm (M-type) and 543.0 nm (M′-type). Fluorescence lifetimes for M-TbTaO{sub 4} and M′-TbTaO{sub 4} were determined as 33.4 μs and 1.25 ms, respectively. M′-type materials seems to be the most suitable for luminescent devices and could be a potential green luminescent material due to the strongest emission if compared with the M-fergusonite type. -- Highlights: ► Terbium orthotantalates were prepared in two different crystalline structures: I2/a and P2/a. ► XRD and Raman scattering showed that the different space groups obtained were exhibited all the 18 Raman-active modes. ► PL decay curves that the Tb{sup 3+} ions occupies only one-symmetry site in both crystallographic arrangements. ► Dominated emission of Tb{sup 3+} ({sup 5}D{sub 4}→{sup 7}F{sub 5}) is centered with a maximum intensity at 549 nm (M-type) and 543 nm (M′-type). ► Fluorescence lifetimes for M-TbTaO{sub 4} and M′-TbTaO{sub 4} were determined as 33.4 μs and 1.25 ms, respectively.

  12. Effect of the boride-nitride hardening on the structure and properties of chromium steel deposited with a flux-cored wire

    Science.gov (United States)

    Eremin, E. N.; Losev, A. S.; Borodikhin, S. A.; Ivlev, K. Ye.

    2017-08-01

    Reliability and durability of pipeline valves are largely determined by the resistance of weld sealing surfaces of its shut-off valve, which in its turn depends on the weld metal properties. To improve the durability of valves a new composition of a high chromium flux-cored wire with a boride compounds complex (BN, TiB2, ZrB2) producing weld composite metal is developed. It is stated that the formation of the martensitic matrix with a reduced structural fragments average size due to appearance of dispersed boride-nitride phases in this metal has resulted in high coating hardness and wear resistance. The original version of this article supplied to AIP Publishing was incomplete and omitted the acknowledgement statement. The full acknowledgement reads: The work was carried out at the expense of a grant from the Russian Science Foundation (No. 17-19-01224).

  13. Laser control and temperature switching of luminescence intensity in photostable transparent film based on terbium(III) β-diketonate complex

    Science.gov (United States)

    Lapaev, Dmitry V.; Nikiforov, Victor G.; Safiullin, Georgy M.; Lobkov, Vladimir S.; Salikhov, Kev M.; Knyazev, Andrey A.; Galyametdinov, Yury G.

    2014-11-01

    The study of the terbium(III) and gadolinium(III) β-diketonate complexes by photoluminescence spectroscopy reveals considerable changes of the photophysical properties of the complexes under the UV laser irradiation. The measurements show the enhancement of the luminescence intensities in the vitrified transparent film of the terbium(III) complex as well as the gadolinium(III) complex under the 337 nm laser irradiation at room temperature. The irradiated film of the terbium(III) complex restores the initial photophysical properties after heating close to the melting temperature (∼353 K) and cooling. We observe no change of the luminescent properties of the irradiated film for months. These features can be used for the design of new lanthanide-based photostable systems with laser control of the luminescence intensity.

  14. Low-cost industrially available molybdenum boride and carbide as “platinum-like” catalysts for the hydrogen evolution reaction in biphasic liquid systems

    OpenAIRE

    Scanlon, Micheal Diarmaid; Bian, Xiaojun; Vrubel, Heron; Amstutz, Véronique; Schenk, Kurt; Hu, Xile; Liu, Baohong; Girault, Hubert

    2013-01-01

    Rarely reported low cost molybdenum boride and carbide microparticles both of which are available in abundant quantities due to their widespread use in industry adsorb at aqueous acid 12 dichloroethane interfaces and efficiently catalyse the hydrogen evolution reaction in the presence of the organic electron donor decamethylferrocene. Kinetic studies monitoring biphasic reactions by UV/vis spectroscopy and further evidence provided by gas chromatography highlight (a) their superior rates of c...

  15. Development of functionalized terbium fluorescent nanoparticles for antibody labeling and time-resolved fluoroimmunoassay application.

    Science.gov (United States)

    Ye, Zhiqiang; Tan, Mingqian; Wang, Guilan; Yuan, Jingli

    2005-01-15

    Silica-based functionalized terbium fluorescent nanoparticles were prepared, characterized and developed as a fluorescence probe for antibody labeling and time-resolved fluoroimmunoassay. The nanoparticles were prepared in a water-in-oil (W/O) microemulsion containing a strongly fluorescent Tb(3+) chelate, N,N,N(1),N(1)-[2,6-bis(3'-aminomethyl-1'-pyrazolyl)phenylpyridine] tetrakis(acetate)-Tb(3+) (BPTA-Tb(3+)), Triton X-100, octanol, and cyclohexane by controlling copolymerization of tetraethyl orthosilicate (TEOS) and 3-[2-(2-aminoethylamino)ethylamino]propyl-trimethoxysilane (AEPS) with ammonia water. The characterizations by transmission electron microscopy and fluorometric methods show that the nanoparticles are spherical and uniform in size, 45 +/- 3nm in diameter, strongly fluorescent with fluorescence quantum yield of 10% and a long fluorescence lifetime of 2.0ms. The amino groups directly introduced to the nanoparticle's surface by using AEPS in the preparation made the surface modification and bioconjugation of the nanoparticles easier. The nanoparticle-labeled anti-human alpha-fetoprotein antibody was prepared and used for time-resolved fluoroimmunoassay of alpha-fetoprotein (AFP) in human serum samples. The assay response is linear from 0.10ngml(-1) to about 100ngml(-1) with the detection limit of 0.10ngml(-1). The coefficient variations (CVs) of the method are less than 9.0%, and the recoveries are in the range of 84-98% for human serum sample measurements.

  16. Highly efficient precipitation of phosphoproteins using trivalent europium, terbium, and erbium ions

    Energy Technology Data Exchange (ETDEWEB)

    Guezel, Yueksel; Rainer, Matthias; Mirza, Munazza Raza; Bonn, Guenther K. [Leopold-Franzens University, Institute of Analytical Chemistry and Radiochemistry, Innsbruck (Austria)

    2012-05-15

    This study describes a highly efficient method for the selective precipitation of phosphoproteins by trivalent europium, terbium, and erbium metal ions. These metal cations belong to the group of lanthanides and are known to be hard acceptors with an overwhelming preference for oxygen-containing anions such as phosphates to which they form very tight ionic bonds. The method could be successfully applied to specifically precipitate phosphoproteins from complex samples including milk and egg white by forming solid metal-protein complexes. Owing to the low solubility product of the investigated lanthanide salts, the produced metal-protein complexes showed high stability. The protein pellets were extensively washed to remove nonphosphorylated proteins and contaminants. For the analysis of proteins the pellets were first dissolved in 30 % formic acid and subjected to matrix-assisted laser desorption/ionization-time of flight (MALDI-TOF) MS. For peptide mass-fingerprint analysis the precipitated phosphoproteins were enzymatically digested using microwave-assisted digestion. The method was found to be highly specific for the isolation and purification of phosphoproteins. Protein quantification was performed by colorimetric detection of total precipitated phosphoproteins and revealed more than 95 % protein recovery for each lanthanide salt. (orig.)

  17. A Terbium Sensitized Luminescence Method for the Assay of Flubiprofen in Pharmaceutical Formulations

    Directory of Open Access Journals (Sweden)

    Salma M.Z. Al-Kindy

    2014-12-01

    Full Text Available A sensitive time-resolved luminescence method for the determination of flubiprofen (FLP in methanol and in aqueous solution is described. The method is based on the luminescence sensitization of terbium (Tb3+ by the formation of a ternary complex with FLP in the presence of 4,7 diphenyl 1,10 phenanthroline (DPP as co-ligand, and Tween-20 as surfactant. The signal for Tb-FLP-DPP was monitored at λex  = 285 nm and λem  = 552 nm. Optimum conditions for the formation of the complex in an aqueous system were TRIS buffer, pH 8.0, DPP (2.5Å~10−7  M, Tween-20 (0.30% and 4Å~10-5  mol L-1  of Tb3+  which allowed the determination of 20–1000 ng mL-1  of FLP with a limit of detection (LOD of 10 ng mL-1 . The relative standard deviations of the method ranged between 0.6 and 1.4% indicating excellent reproducibility of the method. The proposed method was successfully applied for the assays of FLP in pharmaceutical formulations and spiked tap water samples with average recoveries of 87% – 95%.

  18. Sensitization effects of supramolecular assemblies on the luminescence of terbium-ion prulifloxacin complexes

    Energy Technology Data Exchange (ETDEWEB)

    Wang Hong; Yi Chongyue; Li Xue; Fang Fang [School of Chemistry and Chemical Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Yang Yajiang, E-mail: yjyang@mail.hust.edu.c [School of Chemistry and Chemical Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2011-04-15

    Luminescence enhancement of terbium-ion prulifloxacin complexes (Tb(III)-PUFX) in supramolecular hydrogels formed by assembly of 1,3:2,4-di-O-benzylidene-D-sorbitol (DBS) was investigated by steady-state fluorescence, varying temperature fluorescence and time-resolved fluorescence. The luminescence images show that Tb(III)-PUFX were dispersed in the DBS gels. The luminescence intensity of Tb(III)-PUFX in the DBS gels was significantly increased in comparison with that in corresponding aqueous solutions. The varying temperature fluorescent spectra show that the luminescence intensity of Tb(III)-PUFX decreased with an increase in the temperature. This implies that the luminescence enhancement of Tb(III)-PUFX is related to the dissociation and the formation of the DBS assemblies. Time-resolved fluorescence measurements show slower rotational motion in DBS gels in comparison with that in the corresponding aqueous solutions. This may be ascribed to a unique microstructure of three-dimensional network formed by DBC aggregates, resulting in deactivation of the nonradiative relaxation. The images of field emission scanning electron microscopy and polarized optical microscopy indicate that the morphology of the DBS assemblies was not influenced upon addition of Tb(III)-PUFX to the DBS gels.

  19. A Nanoscale Multiresponsive Luminescent Sensor Based on a Terbium(III) Metal-Organic Framework.

    Science.gov (United States)

    Dang, Song; Wang, Ting; Yi, Feiyan; Liu, Qinghui; Yang, Weiting; Sun, Zhong-Ming

    2015-08-01

    A nanoscale terbium-containing metal-organic framework (nTbL), with a layer-like structure and [H2 NMe2 ](+) cations located in the framework channels, was synthesized under hydrothermal conditions. The structure of the as-prepared sample was systematically confirmed by powder XRD and elemental analysis; the morphology was characterized by field-emission SEM and TEM. The photoluminescence studies revealed that rod-like nTbL exhibited bright-green emission, corresponding to (5)D4 →(7)FJ (J=6-3) transitions of the Tb(3+) ion under excitation. Further sensing measurements revealed that as-prepared nTbL could be utilized as a multiresponsive luminescent sensor, which showed significant and exclusive detection ability for Fe(3+) ions and phenylmethanol. These results highlight the practical applications of lanthanide-containing metal-organic frameworks as fluorescent probes. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Terbium-Doped VO2 Thin Films: Reduced Phase Transition Temperature and Largely Enhanced Luminous Transmittance.

    Science.gov (United States)

    Wang, Ning; Duchamp, Martial; Dunin-Borkowski, Rafal E; Liu, Shiyu; Zeng, XianTing; Cao, Xun; Long, Yi

    2016-01-26

    Vanadium dioxide (VO2) is a well-known thermochromic material with large IR modulating ability, promising for energy-saving smart windows. The main drawbacks of VO2 are its high phase transition temperature (τ(c) = 68°C), low luminous transmission (T(lum)), and weak solar modulating ability (ΔT(sol)). In this paper, the terbium cation (Tb(3+)) doping was first reported to reduce τ(c) and increase T(lum) of VO2 thin films. Compared with pristine VO2, 2 at. % doping level gives both enhanced T(lum) and ΔT(sol) from 45.8% to 54.0% and 7.7% to 8.3%, respectively. The T(lum) increases with continuous Tb(3+) doping and reaches 79.4% at 6 at. % doping level, representing ∼73.4% relative increment compared with pure VO2. This has surpassed the best reported doped VO2 thin films. The enhanced thermochromic properties is meaningful for smart window applications of VO2 materials.

  1. Luminescent investigations of terbium(III) biosorption as a surrogate for heavy metals and radionuclides.

    Science.gov (United States)

    Achyuthan, Komandoor E; Arango, Dulce C; Carles, Elizabeth L; Cutler, Christopher E; Meyer, Lauren A; Brozik, Susan M

    2009-07-01

    We describe a metal transport system for investigating the interfacial interactions between the anionic surface charge of a gram-negative bacterium (Escherichia coli) and a trivalent cationic metal, Tb3+. We believe this is the first description of the uptake kinetics, sub- and intracellular distribution, and temporal fate of Tb3+ ion in E. coli. We used the luminescence of the terbium-dipicolinic acid chelate to study metal ion transport. The bacteria had a high tolerance for the metal (IC(50) = 4 mM Tb3+). Metal ion transport was passive and metabolism independent. The uptake kinetics rapidly reached a maximum within 15 min, followed by a stasis for 60 min, and declining thereafter between 120 and 240 min, resulting in a biphasic curve. During this period, greater than one-third of the metal ion was sequestered within the cell. Our choice of a safe Biosafety Level I E. coli bacteria and the relatively non-toxic Tb3+ metal represents a model system for luminescent investigations of biosorption, for studying bacterial-water interfacial chemistry and for the bioremediation of heavy metals and radionuclides.

  2. Processing development of 4 tantalum carbide-hafnium carbide and related carbides and borides for extreme environments

    Science.gov (United States)

    Gaballa, Osama Gaballa Bahig

    Carbides, nitrides, and borides ceramics are of interest for many applications because of their high melting temperatures and good mechanical properties. Wear-resistant coatings are among the most important applications for these materials. Materials with high wear resistance and high melting temperatures have the potential to produce coatings that resist degradation when subjected to high temperatures and high contact stresses. Among the carbides, Al4SiC4 is a low density (3.03 g/cm3), high melting temperature (>2000°C) compound, characterized by superior oxidation resistance, and high compressive strength. These desirable properties motivated this investigation to (1) obtain high-density Al4SiC4 at lower sintering temperatures by hot pressing, and (2) to enhance its mechanical properties by adding WC and TiC to the Al4SiC4. Also among the carbides, tantalum carbide and hafnium carbide have outstanding hardness; high melting points (3880°C and 3890°C respectively); good resistance to chemical attack, thermal shock, and oxidation; and excellent electronic conductivity. Tantalum hafnium carbide (Ta4HfC 5) is a 4-to-1 ratio of TaC to HfC with an extremely high melting point of 4215 K (3942°C), which is the highest melting point of all currently known compounds. Due to the properties of these carbides, they are considered candidates for extremely high-temperature applications such as rocket nozzles and scramjet components, where the operating temperatures can exceed 3000°C. Sintering bulk components comprised of these carbides is difficult, since sintering typically occurs above 50% of the melting point. Thus, Ta4 HfC5 is difficult to sinter in conventional furnaces or hot presses; furnaces designed for very high temperatures are expensive to purchase and operate. Our research attempted to sinter Ta4HfC5 in a hot press at relatively low temperature by reducing powder particle size and optimizing the powder-handling atmosphere, milling conditions, sintering

  3. Construction of the energy matrix for complex atoms. Part VIII: Hyperfine structure HPC calculations for terbium atom

    Science.gov (United States)

    Elantkowska, Magdalena; Ruczkowski, Jarosław; Sikorski, Andrzej; Dembczyński, Jerzy

    2017-11-01

    A parametric analysis of the hyperfine structure (hfs) for the even parity configurations of atomic terbium (Tb I) is presented in this work. We introduce the complete set of 4fN-core states in our high-performance computing (HPC) calculations. For calculations of the huge hyperfine structure matrix, requiring approximately 5000 hours when run on a single CPU, we propose the methods utilizing a personal computer cluster or, alternatively a cluster of Microsoft Azure virtual machines (VM). These methods give a factor 12 performance boost, enabling the calculations to complete in an acceptable time.

  4. Spectrofluorimetric determination of human serum albumin using terbium-danofloxacin probe.

    Science.gov (United States)

    Ramezani, Amir M; Manzoori, Jamshid L; Amjadi, Mohammad; Jouyban, Abolghasem

    2012-01-01

    A spectrofluorimetric method is proposed for the determination of human serum albumin (HSA) and bovine serum albumin (BSA) using terbium-danofloxacin (Tb(3+)-Dano) as a fluorescent probe. These proteins remarkably enhance the fluorescence intensity of the Tb(3+)-Dano complex at 545 nm, and the enhanced fluorescence intensity of Tb(3+)-Dano is proportional to the concentration of proteins (HSA and BSA). Optimum conditions for the determination of HSA were investigated and found that the maximum response was observed at: pH = 7.8, [Tb(3+)] = 8.5 × 10(-5) mol L(-1), [Dano] = 1.5 × 10(-4) mol L(-1). The calibration graphs for standard solutions of BSA, HSA, and plasma samples of HSA were linear in the range of 0.2 × 10(-6) - 1.3 × 10(-6) mol L(-1), 0.2 × 10(-6) - 1.4 × 10(-6) mol L(-1), and 0.2 × 10(-6) - 1 × 10(-6) mol L(-1), respectively. The detection limits (S/N = 3) for BSA, HSA, and plasma sample of HSA were 8.7 × 10(-8) mol L(-1), 6.2 × 10(-8) mol L(-1), and 8.1 × 10(-8) mol L(-1), respectively. The applicability of the method was checked using a number of real biological plasma samples and was compared with the UV spectrometric reference method. The results was showed that the method could be regarded as a simple, practical, and sensitive alternative method for determination of albumin in biological samples.

  5. Spectrofluorimetric Determination of Human Serum Albumin Using Terbium-Danofloxacin Probe

    Directory of Open Access Journals (Sweden)

    Amir M. Ramezani

    2012-01-01

    Full Text Available A spectrofluorimetric method is proposed for the determination of human serum albumin (HSA and bovine serum albumin (BSA using terbium-danofloxacin (Tb3+-Dano as a fluorescent probe. These proteins remarkably enhance the fluorescence intensity of the Tb3+-Dano complex at 545 nm, and the enhanced fluorescence intensity of Tb3+-Dano is proportional to the concentration of proteins (HSA and BSA. Optimum conditions for the determination of HSA were investigated and found that the maximum response was observed at: pH=7.8, [Tb3+] =8.5×10−5 mol L−1, [Dano] =1.5×10−4 mol L−1. The calibration graphs for standard solutions of BSA, HSA, and plasma samples of HSA were linear in the range of 0.2×10−6−1.3×10−6 mol L−1, 0.2×10−6−1.4×10−6 mol L−1, and 0.2×10−6−1×10−6 mol L−1, respectively. The detection limits (S/N = 3 for BSA, HSA, and plasma sample of HSA were 8.7×10−8 mol L−1, 6.2×10−8 mol L−1, and 8.1×10−8 mol L−1, respectively. The applicability of the method was checked using a number of real biological plasma samples and was compared with the UV spectrometric reference method. The results was showed that the method could be regarded as a simple, practical, and sensitive alternative method for determination of albumin in biological samples.

  6. Determination of flavonoids in pharmaceutical preparations using Terbium sensitized fluorescence method

    Directory of Open Access Journals (Sweden)

    M Shaghaghi

    2009-12-01

    Full Text Available "nBackground and the Purpose of the Study: The aim of this study was development and validation of a simple, rapid and sensitive spectrofluorimetric method for determination of total flavonoids in two topical formulations of Calendula officinalis, Ziziphus Spina-christi and an oral drop of Hypiran perforatum L. The proposed method is based on the formation of terbium (Tb3+ "n-flavonoids (quercetin as a reference standard complex at pH 7.0, which has fluorescence intensely with maximum emission at 545 nm when excited at 310 nm. "nMethod "n: For ointments masses of topical formulations were weighed and added to ethanol-aqueous buffer (pH 10.0 and the resulting mixtures were shaken and then two phases were separated by centrifugation. Aqueous phases were filtered and then diluted with water. For Hypiran drops an appropriate portion was diluted with ethanol and then aliquots of sample or standard solutions were determined according to the experimental procedure. "nResults "n: Under the optimum conditions, total concentrations of flavonoids (as quercetin equivalent in three tested formulations were found to be 0.204 mg/g (for Dermatin cream, 0.476 mg/g (for Calendula ointment and 13.50 μg/ml (for Hypiran drops. Analytical recoveries from samples spiked with different amounts of quercetin were 96.1-104.0 % with RSD % of less than 3.5. Conclusion : The proposed method which requires a simple dissolution step without any matrix interferences provided high sensitivity and selectivity and was easily applied to determine total flavonoids in real samples of three investigated formulations with excellent reproducibility.

  7. TOF SIMS analysis and generation of white photoluminescence from strontium silicate codoped with europium and terbium

    Energy Technology Data Exchange (ETDEWEB)

    Tshabalala, Modiehi A.; Swart, Hendrik C.; Ntwaeaborwa, Odireleng M., E-mail: ntwaeab@ufs.ac.za [Department of Physics, University of the Free State, P.O Box 339, Bloemfontein 9300 South Africa (South Africa)

    2014-03-15

    White light emitting terbium (Tb{sup 3+}) and europium (Eu{sup 3+}) codoped strontium silicate (Sr{sub 2}SiO{sub 4}) phosphors were prepared by a solid state reaction process. The structure, particle morphology, chemical composition, ion distribution, photoluminescence (PL), and decay characteristics of the phosphors were analyzed by x-ray diffraction (XRD), scanning electron microscopy (SEM), time-of-flight secondary ion mass spectrometry (TOF-SIMS), and PL spectroscopy, respectively. The XRD data showed that our Sr{sub 2}SiO{sub 4} composed of two phases, namely, β-Sr{sub 2}SiO{sub 4} and α′-Sr{sub 2}SiO{sub 4}, and the α′-Sr{sub 2}SiO{sub 4} phase was more prominent than the β-Sr{sub 2}SiO{sub 4} phase. The SEM micrographs showed that the particles were agglomerated together and they did not have definite shapes. All ions (i.e., negative and positive) present in our materials were identified by TOF-SIMS. In addition, the chemical imaging performed with the TOF-SIMS demonstrated how the individual ions including the dopants (Eu{sup 3+} and Tb{sup 3+}) were distributed in the host lattice. White photoluminescence was observed when the Sr{sub 2}SiO{sub 4}:Tb{sup 3+}, Eu{sup 3+} phosphor was excited at 239 nm using a monochromatized xenon lamp as the excitation source. The phosphor exhibited fast decay lifetimes implying that it is not a good candidate for long afterglow applications.

  8. Synthesis, crystal structure and photophysical properties of europium(III) and terbium(III) complexes with pyridine-2,6-dicarboxamide

    NARCIS (Netherlands)

    Tanase, S.; Gallego, P.M.; Gelder, R. de; Fu, W.T.

    2007-01-01

    The reactions of pyridine-2,6-dicarboxamide with europium(III) and terbium(III) triflates led to the formation of mononuclear complexes of formula [Ln(pcam)(3)](CF3SO3)(3) (Ln = Eu 1, Tb 2; pcam stands for pyridine-2,6-dicarboxamide). From single-crystal X-ray diffraction analysis, the complexes

  9. Zinc sulfide and terbium-doped zinc sulfide films grown by traveling wave reactor atomic layer epitaxy

    CERN Document Server

    Yun, S J; Nam, K S

    1998-01-01

    Zinc sulfide (ZnS) and terbium-doped ZnS (ZnS:Tb) thin films were grown by traveling wave reactor atomic layer epitaxy (ALE). In the present work, ZnCl sub 2 , H sub 2 S, and tris (2,2,6,6-tetramethyl-3,5-heptandionato) terbium (Tb(tmhd) sub 3) were used as the precursors. The dependence of crystallinity and Cl content of ZnS films was investigated on the growth temperature. ZnS and ZnS:Tb films grown at temperatures ranging from 400 to 500 .deg. C showed a hexagonal-2H crystalline structure. The crystallinity of ZnS film was greatly enhanced as the temperature increased. At growth temperatures higher than 450.deg.C, the films showed preferred orientation with mainly (002) diffraction peak. The Cl content decreased from approximately 9 to 1 at.% with the increase in growth temperature from 400 to 500 .deg. C. The segregation of Cl near the surface region and the incorporation of O from Tb(tmhd) sub 3 during ALE process were also observed using Auger electron spectroscopy. The ALE-grown ZnS and ZnS:Tb films re...

  10. Commercializing potassium terbium fluoride, KTF (KTb3F10) faraday crystals for high laser power optical isolator applications

    Science.gov (United States)

    Schlichting, Wolfgang; Stevens, Kevin; Foundos, Greg; Payne, Alexis

    2017-10-01

    Many scientific lasers and increasingly industrial laser systems operate in power regime, require high-performance optical isolators to prevent disruptive light feedback into the laser cavity. The optically active Faraday material is the key optical element inside the isolator. SYNOPTICS has been supplying the laser market with Terbium Gallium Garnet (TGG - Tb3Ga5O12) for many years. It is the most commonly used material for the 650-1100nm range and the key advantages for TGG include its cubic crystal structure for alignment free processing, little to no intrinsic birefringence, and ease of manufacture. However, for high-power laser applications TGG is limited by its absorption at 1064nm and its thermo-optic coefficient, dn/dT. Specifically, thermal lensing and depolarization effects become a limiting factor at high laser powers. While TGG absorption has improved significantly over the past few years, there is an intrinsic limit. Now, SYNOPTICS is commercializing the enhanced new crystal Potassium Terbium Fluoride KTF (KTb3F10) that exhibits much smaller nonlinear refractive index and thermo-optic coefficients, and still exhibits a Verdet constant near that of TGG. This cubic crystal has relatively low absorption and thermo-optic coefficients. It is now fully characterized and available for select production orders. At OPTIFAB in October 2017 we present recent results comparing the performance of KTF to TGG in optical isolators and show SYNOPTICS advances in large volume crystal growth and the production ramp up.

  11. Preparation and photoluminescence enhancement in terbium(III ternary complexes with β-diketone and monodentate auxiliary ligands

    Directory of Open Access Journals (Sweden)

    Devender Singh

    2016-12-01

    Full Text Available A series of new solid ternary complexes of terbium(III ion based on β-diketone ligand acetylacetone (acac and monodentate auxiliary ligands (aqua/urea/triphenylphosphineoxide/pyridine-N-oxide had been prepared. The structural characterizations of synthesized ternary compounds were studied by means of elemental analysis, infrared (IR, and proton nuclear magnetic resonance (NMR spectral techniques. The optical characteristics were investigated with absorption as well as photoluminescence spectroscopy. Thermal behavior of compounds was examined by TGA/DTA analysis and all metal complexes were found to have good thermal stability. The luminescence decay time of complexes were also calculated by monitoring at emission wavelength corresponding to 5D4 → 7F5 transition. A comparative inspection of the luminescent behavior of prepared ternary compounds was performed in order to determine the function of auxiliary ligands in the enhancement of luminescence intensity produced by central terbium(III ion. The color coordinates values suggested that compounds showed bright green emission in visible region in electromagnetic spectrum. Complexes producing green light could play a significant role in the fabrication of efficient light conversion molecular devices for display purposes and lightning systems.

  12. A novel route to nanosized molybdenum boride and carbide and/or metallic molybdenum by thermo-synthesis method from MoO 3, KBH 4, and CCl 4

    Science.gov (United States)

    Li, Yuanzhi; Fan, Yining; Chen, Yi

    2003-01-01

    Nanosized molybdenum boride and carbide were synthesized from MoO 3, KBH 4, and CCl 4 by thermo-synthesis method at lower temperature. The relative content of Mo, Mo 2C, and molybdenum boride in the product was decided by the molar ratio between MoO 3, KBH 4, and CCl 4. Increasing the molar ratio of CCl 4 to MoO 3 was favorable to the production of Mo 2C. Increasing the molar ratio of KBH 4 to MoO 3 was favorable to the production of molybdenum boride. By carefully adjusting the reaction conditions and annealing in Ar at 900°C, a single phase of MoB could be obtained.

  13. Two-phase zirconium boride thin film obtained by ultra-short pulsed laser ablation of a ZrB{sub 12} target

    Energy Technology Data Exchange (ETDEWEB)

    De Bonis, A., E-mail: angela.debonis@unibas.it [Dipartimento di Scienze, Università della Basilicata, Viale dell’Ateneo Lucano, 10 -85100 Potenza (Italy); Istituto di Metodologie Inorganiche e dei Plasmi, Consiglio Nazionale delle Ricerche, U.O.S. di Potenza, C.da Santa Loja, 85010 Tito Scalo, Potenza (Italy); Santagata, A. [Istituto di Metodologie Inorganiche e dei Plasmi, Consiglio Nazionale delle Ricerche, U.O.S. di Potenza, C.da Santa Loja, 85010 Tito Scalo, Potenza (Italy); Rau, J.V. [Istituto di Struttura della Materia, Consiglio Nazionale delle Ricerche, Via del Fosso del Cavaliere 100, 00133 Rome (Italy); Latini, A. [Università di Roma “La Sapienza”, Dipartimento di Chimica, Piazzale Aldo Moro, 5 -00185 Rome (Italy); Mori, T. [National Institute for Materials Science (NIMS) WPI Materials Nanoarchitectonics Center (MANA), Namiki 1-1, Tsukuba 305-0044 (Japan); Medici, L. [Istituto di Metodologie per le Analisi Ambientali, Consiglio Nazionale delle Ricerche, U.O.S. di Potenza, C.da Santa Loja, 85010 Tito Scalo, Potenza (Italy); Teghil, R. [Dipartimento di Scienze, Università della Basilicata, Viale dell’Ateneo Lucano, 10 -85100 Potenza (Italy)

    2013-10-15

    Two-phase zirconium boride thin films have been obtained by ultra-short pulsed laser ablation (PLA) of a zirconium dodecaboride (ZrB{sub 12}) target performed in vacuum. The ablation source was a frequency doubled (λ = 527 nm) Nd:glass laser with a pulse duration of 250 fs. Laser induced plasma has been studied by ICCD imaging and time and space resolved optical emission spectroscopy (OES), whereas the deposited films have been characterized by atomic force microscopy, scanning electron microscopy, X-Ray diffraction and micro-Raman spectroscopy. The film morphology and composition have been interpreted on the basis of the laser ablation mechanism.

  14. Synthesis and luminescent study of Ce{sup 3+}-doped terbium-yttrium aluminum garnet

    Energy Technology Data Exchange (ETDEWEB)

    Dotsenko, V.P., E-mail: ssclab@ukr.net [A.V. Bogatsky Physico-Chemical Institute, National Academy of Sciences of Ukraine, Lustdorfskaya doroga 86, 65080 Odessa (Ukraine); Berezovskaya, I.V.; Zubar, E.V.; Efryushina, N.P. [A.V. Bogatsky Physico-Chemical Institute, National Academy of Sciences of Ukraine, Lustdorfskaya doroga 86, 65080 Odessa (Ukraine); Poletaev, N.I.; Doroshenko, Yu.A. [Institute of Combustion and Advanced Technologies, Mechnikov Odessa National University, Dvoryanskaya 2, 65082 Odessa (Ukraine); Stryganyuk, G.B. [Ivan Franko National University of Lviv, Kirilo i Mefodii 8, 79005 Lviv (Ukraine); HASYLAB at DESY, Notkestrasse 85, 22607 Hamburg (Germany); Voloshinovskii, A.S. [Ivan Franko National University of Lviv, Kirilo i Mefodii 8, 79005 Lviv (Ukraine)

    2013-02-15

    Highlights: Black-Right-Pointing-Pointer Ce{sup 3+}-doped garnets (TYAG) were prepared using nanostructured reagents. Black-Right-Pointing-Pointer The Ce{sup 3+} ions cause a very efficient yellow emission of the samples. Black-Right-Pointing-Pointer The reasons for the long wavelength position of this emission are discussed. Black-Right-Pointing-Pointer Contribution from Al atoms to the conduction band of TYAG is quite essential. - Abstract: Terbium-yttrium aluminum garnets (TYAG) doped with Ce{sup 3+} ions have been prepared by solid state reactions between nanostructured oxides of aluminum and rare earths. The luminescent properties of Ce{sup 3+} ions in (Tb{sub 0.8}Y{sub 0.2}){sub 3(1-x)}Ce{sub 3x}Al{sub 5}O{sub 12} (x = 0.03) have been studied upon excitation in the 2-20 eV region. The substitution of Tb{sup 3+} for Y{sup 3+} in the garnet structure results in broadening the emission band and shifting its maximum towards the longer wavelengths. It was found that in addition to the 4f{sup n} {yields} 4f{sup n-1}5d excitation bands of Ce{sup 3+} and Tb{sup 3+} ions, the excitation spectra for the Ce{sup 3+} emission contain broad bands at 6.73 and {approx}9.5 eV. These bands are attributed to the Ce{sup 3+}-bound exciton formation and O 2p {yields} Al 3s, 3p transitions, respectively. In contrast to the predictions based on the results of electronic structure calculations on Y{sub 3}Al{sub 5}O{sub 12} and Tb{sub 4}Al{sub 2}O{sub 9}, the threshold of interband transitions in TYAG is at high energies ( Greater-Than-Or-Slanted-Equal-To 7.3 eV), and contributions from Al{sub tetr} and Al{sub oct} atoms to the conduction-band density of states are evaluated as quite essential.

  15. Effect of higher borides and inhomogeneity of oxygen distribution on critical current density of undoped and doped magnesium diboride

    Energy Technology Data Exchange (ETDEWEB)

    Prikhna, T A; Tkach, V M; Savchuk, Ya M; Dub, S N; Moshchil, V E; Kozyrev, A V; Sergienko, N V; Melnikov, V S; Shapovalov, A P [Institute for Superhard Materials of the NASU, 2, Avtozavodskaya Str., Kiev 04074 (Ukraine); Gawalek, W; Wendt, M; Dellith, J; Schmidt, Ch; Habisreuther, T; Litzkendorf, D [Institut fuer Photonische Technologien, Albert-Einstein-Strasse 9, Jena, D-07745 (Germany); Danilenko, N I [Institute for Problems of Materialscience of the National Academy of Sciences of Ukraine, 3, Krzhyzhanivsky Str., Kiev 03142 (Ukraine); Weber, H; Eisterer, M [Atomic Institute of the Austrian Universities, 1020 Vienna (Austria); Vajda, J [Budapest University of Technology and Economics, Budapest, Hungary 1111 Budapest, Egry Jozsef u. 18. (Hungary); Sokolovsky, V, E-mail: prikhna@iptelecom.net.u, E-mail: prikhna@mail.r [Ben-Gurion University of the Negev, P.O.B. 653, Beer-Sheva 84105 (Israel)

    2010-06-01

    The effect of doping with Ti, Ta, SiC in complex with synthesis temperature on the amount and distribution of structural inhomogeneities in MgB{sub 2} matrix of high-pressure-synthesized-materials (2 GPa) which can influence pinning: higher borides (MgB{sub 12}) and oxygen-enriched Mg-B-O inclusions, was established and a mechanism of doping effect on j{sub c} increase different from the generally accepted was proposed. Near theoretically dense SiC-doped material exhibited j{sub c}= 10{sup 6} A/cm{sup 2} in 1T field and H{sub irr} =8.5 T at 20 K. The highest jc in fields above 9, 6, and 4 T at 10, 20, and 25 K, respectively, was demonstrated by materials synthesized at 2 GPa, 600 {sup 0}C from Mg and B without additions (at 20 K j{sub c}= 10{sup 2} A/cm{sup 2} in 10 T field). Materials synthesized from Mg and B taken up to 1:20 ratio were superconductive. The highest j{sub c} (6x10{sup 4} A/cm{sup 2} at 20 K in zero field, H{sub irr}= 5 T) and the amount of SC phase (95.3% of shielding fraction), T{sub c} being 37 K were demonstrated by materials having near MgB{sub 12} composition of the matrix. The materials with MgB{sub 12} matrix had a doubled microhardness of that with MgB{sub 2} matrix (25{+-}1.1 GPa and 13.08{+-}1.07 GPa, at a load of 4.9 N, respectively).

  16. Structural variations in terbium(III) complexes with 1,3-adamantanedicarboxylate and diverse co-ligands

    Energy Technology Data Exchange (ETDEWEB)

    Thuéry, Pierre, E-mail: pierre.thuery@cea.fr

    2015-07-15

    Terbium nitrate was reacted with 1,3-adamantanedicarboxylic acid (LH{sub 2}) under solvo-hydrothermal conditions with either N,N-dimethylformamide (DMF) or N,N-dimethylacetamide (DMA) as organic solvents. Hydrolysation of the latter co-solvents resulted in the formation of formate or acetate ions, which are present as co-ligands in the 1D coordination polymer [Tb(L)(HCOO)(H{sub 2}O){sub 2}] (1) and the 2D assembly [Tb(L)(CH{sub 3}COO)(H{sub 2}O)] (2). The increase in dimensionality in the latter arises from the higher connectivity provided by acetate versus formate, the L{sup 2−} ligand being bis-chelating in both cases. The complex [Tb{sub 2}(L){sub 3}(H{sub 2}O){sub 5}][Tb{sub 2}(L){sub 3}(H{sub 2}O){sub 4}]·3H{sub 2}O (3), another 1D species, crystallizes alongside crystals of 2. Further addition of cucurbit[6]uril (CB6), with DMF as co-solvent, gave the two complexes [Tb{sub 2}(L){sub 2}(CB6)(H{sub 2}O){sub 6}](NO{sub 3}){sub 2}·6H{sub 2}O (4) and [H{sub 2}NMe{sub 2}]{sub 2}[Tb(L)(HCOO){sub 2}]{sub 2}·CB6·3H{sub 2}O (5). Complex 4 crystallizes as a 3D framework in which Tb(L){sup +} chains are connected by tetradentate CB6 molecules, while 5 unites a carboxylate-bridged anionic 2D planar assembly and layers of CB6 molecules with counter-cations held at both portals. - Graphical abstract: One- to three-dimensional assemblies are formed in terbium(III) complexes with 1,3-adamantanedicarboxylate obtained under solvo-hydrothermal conditions, these species including formate or acetate co-ligands formed in situ, or additional cucurbit[6]uril molecules. - Highlights: • We report structures of terbium(III) complexes with 1,3-adamantanedicarboxylate. • Solvents able to generate co-ligands or counter-ions in situ have been used. • A 3D species including additional cucurbituril molecules is decribed. • One species displays an alternation of metal–organic and organic sheets.

  17. Complete Stokes polarimetry of magneto-optical Faraday effect in a terbium gallium garnet crystal at cryogenic temperatures.

    Science.gov (United States)

    Majeed, Hassaan; Shaheen, Amrozia; Anwar, Muhammad Sabieh

    2013-10-21

    We report the complete determination of the polarization changes caused in linearly polarized incident light due to propagation in a magneto-optically active terbium gallium garnet (TGG) single crystal, at temperatures ranging from 6.3 to 300 K. A 28-fold increase in the Verdet constant of the TGG crystal is seen as its temperature decreases to 6.3 K. In contrast with polarimetry of light emerging from a Faraday material at room temperature, polarimetry at cryogenic temperatures cannot be carried out using the conventional fixed polarizer-analyzer technique because the assumption that ellipticity is negligible becomes increasingly invalid as temperature is lowered. It is shown that complete determination of light polarization in such a case requires the determination of its Stokes parameters, otherwise inaccurate measurements will result with negative implications for practical devices.

  18. Development of Optical Isolators for Visible Light Using Terbium Aluminum Garnet (Tb3Al5O12) Single Crystals

    Science.gov (United States)

    Geho, Mikio; Takagi, Takashi; Chiku, Shinichiro; Fujii, Takashi

    2005-07-01

    We have recently reported the successful growth of incongruently melting terbium aluminum garnet (Tb3Al5O12; TAG) single crystals by the hybrid laser FZ (floating zone) method. Optical property evaluations confirmed a high transmittance and a larger Verdet constant than conventional Tb3Ga5O12 (TGG) crystals and/or Faraday glasses. In this study, we attempted to design, fabricate, and evaluate optical isolators in visible light through near-infrared (NIR) regions using TAG crystals. A finite element method (FEM) simulation of possible models led us to the preferable one based on a radially magnetized magnet. To realize this, we employed a pseudo-radially magnetized magnet. The target wavelengths of the prototype device were 408, 808, and 1064 nm. The typical extinction ratio was more than 30 dB and the insertion loss was less than 0.3 dB for AR-coated devices.

  19. A hydrometallurgical process for the recovery of terbium from fluorescent lamps: Experimental design, optimization of acid leaching process and process analysis.

    Science.gov (United States)

    Innocenzi, Valentina; Ippolito, Nicolò Maria; De Michelis, Ida; Medici, Franco; Vegliò, Francesco

    2016-12-15

    Terbium and rare earths recovery from fluorescent powders of exhausted lamps by acid leaching with hydrochloric acid was the objective of this study. In order to investigate the factors affecting leaching a series of experiments was performed in according to a full factorial plan with four variables and two levels (4 2 ). The factors studied were temperature, concentration of acid, pulp density and leaching time. Experimental conditions of terbium dissolution were optimized by statistical analysis. The results showed that temperature and pulp density were significant with a positive and negative effect, respectively. The empirical mathematical model deducted by experimental data demonstrated that terbium content was completely dissolved under the following conditions: 90 °C, 2 M hydrochloric acid and 5% of pulp density; while when the pulp density was 15% an extraction of 83% could be obtained at 90 °C and 5 M hydrochloric acid. Finally a flow sheet for the recovery of rare earth elements was proposed. The process was tested and simulated by commercial software for the chemical processes. The mass balance of the process was calculated: from 1 ton of initial powder it was possible to obtain around 160 kg of a concentrate of rare earths having a purity of 99%. The main rare earths elements in the final product was yttrium oxide (86.43%) following by cerium oxide (4.11%), lanthanum oxide (3.18%), europium oxide (3.08%) and terbium oxide (2.20%). The estimated total recovery of the rare earths elements was around 70% for yttrium and europium and 80% for the other rare earths. Copyright © 2016 Elsevier Ltd. All rights reserved.

  20. Investigation of the luminescent properties of terbium-anthranilate complexes and application to the determination of anthranilic acid derivatives in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Arnaud, N.; Georges, J

    2003-01-10

    The luminescent properties of terbium complexes with furosemide (FR), flufenamic (FF) acid, tolfenamic (TF) acid and mefenamic (MF) acid have been investigated in aqueous solutions. For all four compounds, complexation occurs when the carboxylic acid of the aminobenzoic group is dissociated and is greatly favoured in the presence of trioctylphosphine oxide as co-ligand and Triton X-100 as surfactant. Under optimum conditions, luminescence of the lanthanide ion is efficiently sensitised and the lifetime of the {sup 5}D{sub 4} resonance level of terbium in the complex is ranging between 1 and 1.9 ms, against 0.4 ms for the aqua ion. The sensitivity of the method for the determination of anthranilic acid derivatives is improved by one to two orders of magnitude with respect to that achieved using native fluorescence or terbium-sensitised luminescence in methanol. The limits of detection are 2x10{sup -10}, 5x10{sup -10} and 2x10{sup -9} mol l{sup -1} for flufenamic acid, furosemide and tolfenamic acid, and mefenamic acid, respectively, with within-run RSD values of less than 1%. The method has been applied to the determination of flufenamic acid in spiked calf sera with and without sample pretreatment. Depending on the method and the analyte concentration, the recovery was ranging between 83 and 113% and the lowest concentration attainable in serum samples was close to 1x10{sup -7} mol l{sup -1}.

  1. Low-cost industrially available molybdenum boride and carbide as "platinum-like" catalysts for the hydrogen evolution reaction in biphasic liquid systems.

    Science.gov (United States)

    Scanlon, Micheál D; Bian, Xiaojun; Vrubel, Heron; Amstutz, Véronique; Schenk, Kurt; Hu, Xile; Liu, BaoHong; Girault, Hubert H

    2013-02-28

    Rarely reported low-cost molybdenum boride and carbide microparticles, both of which are available in abundant quantities due to their widespread use in industry, adsorb at aqueous acid-1,2-dichloroethane interfaces and efficiently catalyse the hydrogen evolution reaction in the presence of the organic electron donor - decamethylferrocene. Kinetic studies monitoring biphasic reactions by UV/vis spectroscopy, and further evidence provided by gas chromatography, highlight (a) their superior rates of catalysis relative to other industrially significant transition metal carbides and silicides, as well as a main group refractory compound, and (b) their highly comparable rates of catalysis to Pt microparticles of similar dimensions. Insight into the catalytic processes occurring for each adsorbed microparticle was obtained by voltammetry at the liquid-liquid interface.

  2. X-Ray photoelectron spectroscopy study of radiofrequency-sputtered titanium, carbide, molybdenum carbide, and titanium boride coatings and their friction properties

    Science.gov (United States)

    Brainard, W. A.; Wheeler, D. R.

    1977-01-01

    Radiofrequency sputtered coatings of titanium carbide, molybdenum carbide and titanium boride were tested as wear resistant coatings on stainless steel in a pin on disk apparatus. X-ray photoelectron spectroscopy (XPS) was used to analyze the sputtered films with regard to both bulk and interface composition in order to obtain maximum film performance. Significant improvements in friction behavior were obtained when properly biased films were deposited on deliberately preoxidized substrates. XPS depth profile data showed thick graded interfaces for bias deposited films even when adherence was poor. The addition of 10 percent hydrogen to the sputtering gas produced coatings with thin poorly adherent interfaces. Results suggest that some of the common practices in the field of sputtering may be detrimental to achieving maximum adherence and optimum composition for these refractory compounds.

  3. The coloring problem in the solid-state metal boride carbide ScB{sub 2}C{sub 2}. A theoretical analysis

    Energy Technology Data Exchange (ETDEWEB)

    Lassoued, Souheila [Universite de Rennes, Ecole Nationale Superieure de Chimie, UMR 6226 CNRS (France). Inst. des Sciences Chimiques; Universite Kasdi Merbah-Ouargla (Algeria). Faculte des Mathematiques et des Sciences de la Matiere; Boucher, Benoit [Universite de Rennes, Ecole Nationale Superieure de Chimie, UMR 6226 CNRS (France). Inst. des Sciences Chimiques; Max-Planck-Institut fuer Chemische Physik Fester Stoffe, Dresden (Germany); Boutarfaia, Ahmed [Universite Kasdi Merbah-Ouargla (Algeria). Faculte des Mathematiques et des Sciences de la Matiere; Gautier, Regis; Halet, Jean-Francois [Universite de Rennes, Ecole Nationale Superieure de Chimie, UMR 6226 CNRS (France). Inst. des Sciences Chimiques

    2016-08-01

    The electronic properties of the layered ternary metal boride carbide ScB{sub 2}C{sub 2}, the structure of which consists of B/C layers made of fused five- and seven-membered rings alternating with scandium sheets, are analyzed. In particular, the respective positions of the B and C atoms (the so-called coloring problem) are tackled using density functional theory, quantum theory of atoms in molecules, and electron localizability indicator calculations. Results reveal that (i) the most stable coloring minimizes the number of B-B and C-C contacts and maximizes the number of boron atoms in the heptagons, (ii) the compound is metallic in character, and (iii) rather important covalent bonding occurs between the metallic sheets and the boron-carbon network.

  4. Synthesis, boron-nonstoichiometry and hardness of perovskite-type rare earth rhodium borides RRh{sub 3}B {sub x} (R = La, Gd, Lu and Sc)

    Energy Technology Data Exchange (ETDEWEB)

    Shishido, T. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan)]. E-mail: shishido@imr.tohoku.ac.jp; Ye, J. [National Institute for Materials Science, 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Okada, S. [Faculty of Engineering, Kokushikan University, 4-28-1 Setagaya-ku, Tokyo 154-8515 (Japan); Kudou, K. [Faculty of Engineering, Kanagawa University, 3-27-1 Rokkakubashi, Kanagawa-ku, Yokohama 221-8686 (Japan); Iizumi, K. [Faculty of Engineering, Tokyo Institute of Polytechnics, 1583 Iiyama, Atsugi 243-0297 (Japan); Oku, M. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Ishizawa, Y. [Department of Environmental Science, Iwaki Meisei University, 5-5-1 Iino, Chuohdai, Iwaki 970-8551 (Japan); Sahara, R.; Kumar, V. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Yoshikawa, A. [Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Tanaka, M. [Photon Factory, High Energy Accelerator Research Organization, 1-1 Oho, Tsukuba 305-0801 (Japan); Horiuchi, H. [Earth Science Laboratory, Faculty of Education, Hirosaki University, 1 Bunkyo-cho, Hirosaki 036-8560 (Japan); Nomura, A.; Sugawara, T.; Obara, K. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Amano, T. [Shonan Institute of Technology, 1-1-25, Tsujido-Nishikaigan, Fujisawa 251-8511 (Japan); Kohiki, S. [Department of Materials Science, Kyusyu Institute of Technology, Kita-Kyusyu 804-8550 (Japan); Kawazoe, Y.; Nakajima, K. [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan)

    2006-02-09

    Rare earth ternary borides, RRh{sub 3}B {sub x} (R = La, Gd, Lu and Sc) have been synthesized by arc melting method. Borides RRh{sub 3}B {sub x} (R = La, Gd, Lu and Sc) have perovskite-type cubic structure: space group Pm3m; Z = 1. The lattice parameters a of the stoichiometric RRh{sub 3}B for R = La, Gd, Lu and Sc are 0.4251(1), 0.4183(1), 0.4126(1) and 0.4080(1) nm, respectively. LaRh{sub 3}B {sub x} does not have boron-nonstoichiometry as x = 0. In GdRh{sub 3}B {sub x} and LuRh{sub 3}B {sub x}, boron- nonstoichiometry ranges between 0.55 {<=} x {<=} 1 and 0.30 {<=} x {<=} 1, respectively. The boron-nonstoichiometry range is the widest, 0 {<=} x {<=} 1, for R = Sc. Boron-nonstoichiometry increases with decreasing atomic radius of R. The microhardness of the stoichiometric RRh{sub 3}B for R = La, Gd, Lu and Sc is 4.2 {+-} 0.1, 6.8 {+-} 0.1, 7.7 {+-} 0.5 and 9.9 {+-} 0.1 GPa, respectively. As a result, microhardness increases with decreasing atomic size of R in RRh{sub 3}B; R is positioned at the eight corners of the cube in the perovskite-type structure. Thus, hardness is strongly dependent on R element. The hardness changes almost linearly with boron concentration x for R = Gd and Lu in RRh{sub 3}B {sub x}, while no linear dependency is found for R = Sc. Ab initio calculations have been performed to obtain the equilibrium lattice constants and the bulk moduli. The calculated lattice constants are in excellent agreement with experimental results.

  5. Structural investigation and photoluminescent properties of gadolinium(III), europium(III) and terbium(III) 3-mercaptopropionate complexes.

    Science.gov (United States)

    Souza, E R; Mazali, I O; Sigoli, F A

    2014-01-01

    This work reports on the synthesis, crystallographic determination and spectroscopic characterization of gadolinium(III), terbium(III) and europium(III) 3-mercaptopropionate complexes, aqua-tris(3-mercaptopropionate)lanthanide(III)--[Ln(mpa)3(H2O)]. The Judd-Ofelt intensity parameters were experimentally determined from emission spectrum of the [Eu(mpa)3(H2O)]complex and they were also calculated from crystallographic data. The complexes are coordination polymers, where the units of each complex are linked together by carboxylate groups leading to an unidimensional and parallel chains that by chemical interactions form a tridimensional framework. The emission spectrum profile of the [Eu(mpa)3(H2O)] complex is discussed based on point symmetry of the europium(III) ion, that explains the bands splitting observed in its emission spectrum. Photoluminescent analysis of the [Gd(mpa)3(H2O)] complex show no efficient ligand excitation but an intense charge transfer band. The excitation spectra of the [Eu(mpa)3(H2O)] and [Tb(mpa)3(H2O)] complexes do not show evidence of energy transfer from the ligand to the excited levels of these trivalent ions. Therefore the emission bands are originated only by direct f-f intraconfigurational excitation of the lantanide(III) ions.

  6. Fluorometric determination of proteins using the terbium (III)-2-thenoyltrifluoroacetone-sodium dodecyl benzene sulfonate-protein system

    Energy Technology Data Exchange (ETDEWEB)

    Jia Zhen [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Department of Chemistry, Dezhou University, Dezhou 253023 (China); Yang Jinghe [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)]. E-mail: yjh@sdu.edu.cn; Wu Xia [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Wang Fei [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Guo Changying [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Liu Shufang [Key Laboratory of Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)

    2006-12-15

    It is found that in hexamethylene tetramine (HMTA)-HCl buffer of pH=8.00, proteins can enhance the fluorescence of terbium (III) (Tb{sup 3+})-2-thenoyltrifluoroacetone (TTA)-sodium dodecyl benzene sulfonate (SDBS) system. Based on this, a sensitive method for the determination of proteins is proposed. The experiments indicate that under the optimum conditions, the enhanced fluorescence intensity is in proportion to the concentration of proteins in the range of 4.0x10{sup -9}-7.5x10{sup -6}g/mL for bovine serum albumin (BSA), 5.0x10{sup -9}-1.5x10{sup -5}g/mL for human serum albumin (HSA), 1.0x10{sup -8}-7.5x10{sup -6}g/mL for egg albumin (EA). Their detection limits (S/N=3) are 0.5, 0.8 and 2.0ng/mL, respectively. The interaction mechanism is also studied.

  7. Terbium to Quantum Dot FRET Bioconjugates for Clinical Diagnostics: Influence of Human Plasma on Optical and Assembly Properties

    Directory of Open Access Journals (Sweden)

    Niko Hildebrandt

    2011-10-01

    Full Text Available Förster resonance energy transfer (FRET from luminescent terbium complexes (LTC as donors to semiconductor quantum dots (QDs as acceptors allows extraordinary large FRET efficiencies due to the long Förster distances afforded. Moreover, time-gated detection permits an efficient suppression of autofluorescent background leading to sub-picomolar detection limits even within multiplexed detection formats. These characteristics make FRET-systems with LTC and QDs excellent candidates for clinical diagnostics. So far, such proofs of principle for highly sensitive multiplexed biosensing have only been performed under optimized buffer conditions and interactions between real-life clinical media such as human serum or plasma and LTC-QD-FRET-systems have not yet been taken into account. Here we present an extensive spectroscopic analysis of absorption, excitation and emission spectra along with the luminescence decay times of both the single components as well as the assembled FRET-systems in TRIS-buffer, TRIS-buffer with 2% bovine serum albumin, and fresh human plasma. Moreover, we evaluated homogeneous LTC-QD FRET assays in QD conjugates assembled with either the well-known, specific biotin-streptavidin biological interaction or, alternatively, the metal-affinity coordination of histidine to zinc. In the case of conjugates assembled with biotin-streptavidin no significant interference with the optical and binding properties occurs whereas the histidine-zinc system appears to be affected by human plasma.

  8. Evidence of mass exchange between inside and outside of sonoluminescing bubble in aqueous solution of terbium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Jinfu, E-mail: liang.shi2007@163.com [School of Physics and Electronic Science, Guizhou Normal University, Guiyang 550001 (China); Chen, Weizhong, E-mail: wzchen@nju.edu.cn [The Key Laboratory of Modern Acoustics, Ministry of Education, Institution of Acoustics, Nanjing University, Nanjing 210093 (China); Wang, Xun; Yang, Jing; Chen, Zhan [The Key Laboratory of Modern Acoustics, Ministry of Education, Institution of Acoustics, Nanjing University, Nanjing 210093 (China)

    2016-12-16

    Highlights: • Time-resolved spectra of SBSL were obtained for Tb{sup 3+} ions emission lines. • Mass exchange between inside and outside of SL bubble was probed via Tb{sup 3+} ions lines. • The argon rectification hypothesis was tested by time-resolved spectra of SBSL. • The rate of mass exchange inside an SBSL bubble increases with increasing sound pressure. - Abstract: Spectra of single-bubble sonoluminescence (SBSL) were obtained for Tb{sup 3+} ions emission lines from bubbles in an aqueous solution of terbium chloride (TbCl{sub 3}). The spectra provide experimental evidence to prove that an air bubble driven by strong ultrasound will not eventually become a rectified pure argon bubble, which is not as predicted by the argon rectification hypothesis. The time-resolved spectra of SBSL show a mass exchange of material such as Tb{sup 3+} ions between the inside and outside of the bubble. With increasing sound pressure, the rate of mass exchange and the SBSL intensity increases.

  9. Optical properties and electrical transport of thin films of terbium(III bis(phthalocyanine on cobalt

    Directory of Open Access Journals (Sweden)

    Peter Robaschik

    2014-11-01

    Full Text Available The optical and electrical properties of terbium(III bis(phthalocyanine (TbPc2 films on cobalt substrates were studied using variable angle spectroscopic ellipsometry (VASE and current sensing atomic force microscopy (cs-AFM. Thin films of TbPc2 with a thickness between 18 nm and 87 nm were prepared by organic molecular beam deposition onto a cobalt layer grown by electron beam evaporation. The molecular orientation of the molecules on the metallic film was estimated from the analysis of the spectroscopic ellipsometry data. A detailed analysis of the AFM topography shows that the TbPc2 films consist of islands which increase in size with the thickness of the organic film. Furthermore, the cs-AFM technique allows local variations of the organic film topography to be correlated with electrical transport properties. Local current mapping as well as local I–V spectroscopy shows that despite the granular structure of the films, the electrical transport is uniform through the organic films on the microscale. The AFM-based electrical measurements allow the local charge carrier mobility of the TbPc2 thin films to be quantified with nanoscale resolution.

  10. Highly luminescent charge-neutral europium(iii) and terbium(iii) complexes with tridentate nitrogen ligands.

    Science.gov (United States)

    Senthil Kumar, Kuppusamy; Schäfer, Bernhard; Lebedkin, Sergei; Karmazin, Lydia; Kappes, Manfred M; Ruben, Mario

    2015-09-21

    We report on the synthesis of tridentate-nitrogen pyrazole-pyridine-tetrazole (L(1)H) and pyrazole-pyridine-triazole (L(2)H) ligands and their complexation with lanthanides (Ln = Gd(iii), Eu(iii) and Tb(iii)) resulting in stable, charge-neutral complexes Ln(L(1))3 and Ln(L(2))3, respectively. X-ray crystallographic analysis of the complexes with L(1) ligands revealed tricapped trigonal coordination geometry around the lanthanide ions. All complexes show bright photoluminescence (PL) in the solid state, indicating efficient sensitization of the lanthanide emission via the triplet states of the ligands. In particular, the terbium complexes show high PL quantum yields of 65 and 59% for L(1) and L(2), respectively. Lower PL efficiencies of the europium complexes (7.5 and 9%, respectively) are attributed to large energy gaps between the triplet states of the ligands and accepting levels of Eu(iii). The triplet state energy can be reduced by introducing an electron withdrawing (EW) group at the 4 position of the pyridine ring. Such substitution of L(1)H with a carboxylic ester (COOMe) EW group leads to a europium complex with increased PL quantum yield of 31%. A comparatively efficient PL of the complexes dissolved in ethanol indicates that the lanthanide ions are shielded against nonradiative deactivation via solvent molecules.

  11. Micelle enhanced and terbium sensitized spectrofluorimetric determination of danofloxacin in milk using molecularly imprinted solid phase extraction

    Science.gov (United States)

    Kaur, Kuldeep; Saini, Shivender Singh; Malik, Ashok Kumar; Singh, Baldev

    2012-10-01

    An efficient molecularly imprinted solid phase extraction (MISPE)-spectrofluorimetric method was developed to sensitively determine danofloxacin (DAN) in milk samples. Solid phase extraction procedure using MISPE cartridges was first performed on milk samples and then spectrofluorimetric determination was done at 546 nm using an excitation wavelength of 285 nm in presence of terbium and sodium dodecyl benzene sulfonate (SDBS). It was found that SDBS significantly enhanced the fluorescence intensity of the DAN-Tb3+ complex. Various factors affecting the fluorescence intensity of DAN-Tb3+-SDBS system were studied and conditions were optimized. The enhanced fluorescence intensity of the system (ΔF) showed a good linear relationship with the concentration of DAN over the range of 8.4 × 10-9-3.4 × 10-7 mol L-1 with a correlation coefficient of 0.9996. The detection limit was determined as 2.0 × 10-9 mol L-1 and the limit of quantification was determined as 6.5 × 10-9 mol L-1. The MISPE-spectrofluorimetric procedure was successfully applied to the determination of DAN in milk samples. The method is simple, rapid, sensitive and allows interference free determination of DAN in complex fluorescent matrices like milk. The method can be used to determine whether the DAN residues in milk exceed MRLs or not.

  12. Study of quantum dot based on tin/yttrium mixed oxide doped with terbium to be used as biomarker

    Energy Technology Data Exchange (ETDEWEB)

    Paganini, Paula P.; Felinto, Maria Claudia F.C.; Kodaira, Claudia A., E-mail: paulapaganini@usp.b, E-mail: mfelinto@ipen.b, E-mail: claudiakodaira@yahoo.co [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Brito, Hermi F., E-mail: hefbrito@iq.usp.b [Universidade de Sao Paulo (USP), SP (Brazil). Inst. de Quimica. Lab. de Elementos do Bloco f; Nunes, Luiz Antonio O., E-mail: luizant@ifsc.usp.b [Universidade de Sao Paulo (USP), Sao Carlos, SP (Brazil). Inst. de Fisica. Dept. de Fisica e Informatica

    2009-07-01

    Quantum dots (semiconductors nanocrystals) have brought a promising field to develop a new generation of luminescent biomarkers. The use of lanthanides ions as luminescent markers has many advantages, for example a security method, low cost, high specificity and also the luminescence can be promptly measured with high sensibility and accuracy. These luminescent dots are functionalized with biomolecules. For the luminophore particle to be connect with biologicals molecules (for example covalent antibody) is necessary a previous chemical treatment to modify luminophore particle surface and this process is called functionalization. A prior chemical treatment with changes on the surface luminophore particle is necessary to couple the luminophore to biological molecules. This process can be used as coating which can protect these particles from being dissolved by acid as well as provide functional groups for biological conjugation. This work presents a photoluminescence study of nanoparticles based on tin/yttrium mixed oxides doped with terbium (SnO{sub 2}/Y{sub 2}O{sub 3}:Tb{sup 3+}), synthesized by coprecipitation method. The nanoparticles were submitted to thermal treatment and characterized by X-Ray Powder Diffraction (XRD) that showed cassiterite phase formation and the influence of thermal treatment on nanoparticles structures. These nanoparticles going to be functionalized with a natural polysaccharide (chitosan) in order to form microspheres. These microspheres going to be irradiated with gamma radiation to sterilization and it can be evaluated if the nanoparticles are resistant to irradiation and they do not lose functionality with this process. (author)

  13. A Study on the Effect of the Boron Potential on the Mechanical Properties of the Borided Layers Obtained by Boron Diffusion at the Surface of AISI 316L Steel

    Directory of Open Access Journals (Sweden)

    E. Hernández-Sánchez

    2014-01-01

    Full Text Available The effect of the boron potential on the thickness and the mechanical properties of borided layers was evaluated. The boron potential was established by means of the available atoms of boron contained in a control volume inside a cylinder. The cylinders were manufactured from AISI 316L steel, and the boriding treatment was performed using the powder pack technique at a temperature of 1273 K over an exposure time of 6 h. Four different internal diameters of the cylinders were evaluated (3.17, 4.76, 6.35, and 7.93 mm. The mechanical properties were evaluated using the Berkovich instrumented indentation technique. The results showed a clear influence of the boron potential on the mechanical properties of the layers. The hardness of the layers was stablished in the range of 16.22 to 21.16 GPa. Young’s modulus values were stablished in the range of 255.96 to 341.37 GPa. Also the fracture toughness and brittleness of the layers reflected the influence of the boron potential supplied during the boriding process. Finally, the influence of the boron potential on the constant of parabolic growth (K was also established as a function of the inner diameter of the cylinders.

  14. Terbium-doped gadolinium oxysulfide (Gd2O2S:Tb) scintillation-based polymer optical fibre sensor for real time monitoring of radiation dose in oncology

    Science.gov (United States)

    Lewis, E.; O'Keeffe, S.; Grattan, M.; Hounsell, A.; McCarthy, D.; Woulfe, P.; Cronin, J.; Mihai, L.; Sporea, D.; Santhanam, A.; Agazaryan, N.

    2014-05-01

    A PMMA based plastic optical fibre sensor for use in real time radiotherapy dosimetry is presented. The optical fibre tip is coated with a scintillation material, terbium-doped gadolinium oxysulfide (Gd2O2S:Tb), which fluoresces when exposed to ionising radiation (X-Ray). The emitted visible light signal penetrates the sensor optical fibre and propagates along the transmitting fibre at the end of which it is remotely monitored using a fluorescence spectrometer. The results demonstrate good repeatability, with a maximum percentage error of 0.5% and the response is independent of dose rate.

  15. New ternary tantalum borides containing boron dumbbells: Experimental and theoretical studies of Ta{sub 2}OsB{sub 2} and TaRuB

    Energy Technology Data Exchange (ETDEWEB)

    Mbarki, Mohammed; Touzani, Rachid St.; Rehorn, Christian W.G.; Gladisch, Fabian C. [Institute of Inorganic Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Fokwa, Boniface P.T., E-mail: bfokwa@ucr.edu [Institute of Inorganic Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Department of Chemistry, University of California Riverside (UCR), Riverside, CA 92521 (United States)

    2016-10-15

    The new ternary transition metal-rich borides Ta{sub 2}OsB{sub 2} and TaRuB have been successfully synthesized by arc-melting the elements in a water-cooled crucible under an argon atmosphere. The crystal structures of both compounds were solved by single-crystal X-ray diffraction and their metal compositions were confirmed by EDX analysis. It was found that Ta{sub 2}OsB{sub 2} and TaRuB crystallize in the tetragonal Nb{sub 2}OsB{sub 2} (space group P4/mnc, no. 128) and the orthorhombic NbRuB (space group Pmma, no. 51) structure types with lattice parameters a=5.878(2) Å, c=6.857(2) Å and a=10.806(2) Å, b=3.196(1) Å, c=6.312(2) Å, respectively. Furthermore, crystallographic, electronic and bonding characteristics have been studied by density functional theory (DFT). Electronic structure relaxation has confirmed the crystallographic parameters while COHP bonding analysis indicates that B{sub 2}-dummbells are the strongest bonds in both compounds. Moreover, the formation of osmium dumbbells in Ta{sub 2}OsB{sub 2} through a Peierls distortion along the c-axis, is found to be the origin of superstructure formation. Magnetic susceptibility measurements reveal that the two phases are Pauli paramagnets, thus confirming the theoretical DOS prediction of metallic character. Also hints of superconductivity are found in the two phases, however lack of single phase samples has prevented confirmation. Furthermore, the thermodynamic stability of the two modifications of AMB (A=Nb, Ta; M =Ru, Os) are studied using DFT, as new possible phases containing either B{sub 4}- or B{sub 2}-units are predicted, the former being the most thermodynamically stable modification. - Graphical abstract: The two new ternary tantalum borides, Ta{sub 2}OsB{sub 2} and TaRuB, have been discovered. Their crystal structures contain boron dumbbells, which are the strongest bonds. Peirls distortion is found responsible for Os{sub 2}-dumbbells formation in Ta{sub 2}OsB{sub 2}. Ta{sub 2}OsB{sub 2} and

  16. Compact all-fiber optical Faraday components using 65-wt%-terbium-doped fiber with a record Verdet constant of -32 rad/(Tm).

    Science.gov (United States)

    Sun, L; Jiang, S; Marciante, J R

    2010-06-07

    A compact all-fiber Faraday isolator and a Faraday mirror are demonstrated. At the core of each of these components is an all-fiber Faraday rotator made of a 4-cm-long, 65-wt%-terbium-doped silicate fiber. The effective Verdet constant of the terbium-doped fiber is measured to be -32 rad/(Tm), which is 27 x larger than that of silica fiber. This effective Verdet constant is the largest value measured to date in any fiber and is 83% of the Verdet constant of commercially available crystal used in bulk optics-based isolators. Combining the all-fiber Faraday rotator with fiber polarizers results in a fully fusion spliced all-fiber isolator whose isolation is measured to be 19 dB. Combining the all-fiber Faraday rotator with a fiber Bragg grating results in an all-fiber Faraday mirror that rotates the polarization state of the reflected light by 88 +/- 4 degrees .

  17. Picomolar Traces of Americium(III) Introduce Drastic Changes in the Structural Chemistry of Terbium(III): A Break in the "Gadolinium Break".

    Science.gov (United States)

    Welch, Jan M; Müller, Danny; Knoll, Christian; Wilkovitsch, Martin; Giester, Gerald; Ofner, Johannes; Lendl, Bernhard; Weinberger, Peter; Steinhauser, Georg

    2017-10-16

    The crystallization of terbium 5,5'-azobis[1H-tetrazol-1-ide] (ZT) in the presence of trace amounts (ca. 50 Bq, ca. 1.6 pmol) of americium results in 1) the accumulation of the americium tracer in the crystalline solid and 2) a material that adopts a different crystal structure to that formed in the absence of americium. Americium-doped [Tb(Am)(H 2 O) 7 ZT] 2 ZT⋅10 H 2 O is isostructural to light lanthanide (Ce-Gd) 5,5'-azobis[1H-tetrazol-1-ide] compounds, rather than to the heavy lanthanide (Tb-Lu) 5,5'-azobis[1H-tetrazol-1-ide] (e.g., [Tb(H 2 O) 8 ] 2 ZT 3 ⋅6 H 2 O) derivatives. Traces of Am seem to force the Tb compound into a structure normally preferred by the lighter lanthanides, despite a 10 8 -fold Tb excess. The americium-doped material was studied by single-crystal X-ray diffraction, vibrational spectroscopy, radiochemical neutron activation analysis, and scanning electron microcopy. In addition, the inclusion properties of terbium 5,5'-azobis[1H-tetrazol-1-ide] towards americium were quantified, and a model for the crystallization process is proposed. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Effect of Heat Treatment on Borides Precipitation and Mechanical Properties of CoCrFeNiAl1.8Cu0.7B0.3Si0.1 High-Entropy Alloy Prepared by Arc-Melting and Laser-Cladding

    Science.gov (United States)

    Zhang, H.; Tang, H.; He, Y. Z.; Zhang, J. L.; Li, W. H.; Guo, S.

    2017-11-01

    Effects of heat treatment on borides precipitation and mechanical properties of arc-melted and laser-cladded CoCrNiFeAl1.8Cu0.7B0.3Si0.1 high-entropy alloys were comparatively studied. The arc-melted alloy contains lots of long strip borides distributed in the body-centered cubic phase, with a hardness about 643 HV0.5. Laser-cladding can effectively inhibit the boride precipitation and the laser-cladded alloy is mainly composed of a simple bcc solid solution, with a high hardness about 769 HV0.5, indicating the strengthening effect by interstitial boron atoms is greater than the strengthening by borides precipitation. Heat treatments between 800°C and 1200°C can simultaneously improve the hardness and fracture toughness of arc-melted alloys, owing to the boride spheroidization, dissolution, re-precipitation, and hence the increased boron solubility and nano-precipitation in the bcc solid solution. By contrast, the hardness of laser-cladded alloys reduce after heat treatments in the same temperature range, due to the decreased boron solubility in the matrix.

  19. Crystal structures of two mononuclear complexes of terbium(III) nitrate with the tripodal alcohol 1,1,1-tris-(hy-droxy-meth-yl)propane.

    Science.gov (United States)

    Gregório, Thaiane; Giese, Siddhartha O K; Nunes, Giovana G; Soares, Jaísa F; Hughes, David L

    2017-02-01

    Two new mononuclear cationic complexes in which the TbIII ion is bis-chelated by the tripodal alcohol 1,1,1-tris-(hy-droxy-meth-yl)propane (H3LEt, C6H14O3) were prepared from Tb(NO3)3·5H2O and had their crystal and mol-ecular structures solved by single-crystal X-ray diffraction analysis after data collection at 100 K. Both products were isolated in reasonable yields from the same reaction mixture by using different crystallization conditions. The higher-symmetry complex dinitratobis[1,1,1-tris-(hy-droxy-meth-yl)propane]-terbium(III) nitrate di-meth-oxy-ethane hemisolvate, [Tb(NO3)2(H3LEt)2]NO3·0.5C4H10O2, 1, in which the lanthanide ion is 10-coordinate and adopts an s-bicapped square-anti-prismatic coordination geometry, contains two bidentate nitrate ions bound to the metal atom; another nitrate ion functions as a counter-ion and a half-mol-ecule of di-meth-oxy-ethane (completed by a crystallographic twofold rotation axis) is also present. In product aqua-nitratobis[1,1,1-tris-(hy-droxy-meth-yl)propane]-terbium(III) dinitrate, [Tb(NO3)(H3LEt)2(H2O)](NO3)2, 2, one bidentate nitrate ion and one water mol-ecule are bound to the nine-coordinate terbium(III) centre, while two free nitrate ions contribute to charge balance outside the tricapped trigonal-prismatic coordination polyhedron. No free water mol-ecule was found in either of the crystal structures and, only in the case of 1, di-meth-oxy-ethane acts as a crystallizing solvent. In both mol-ecular structures, the two tripodal ligands are bent to one side of the coordination sphere, leaving room for the anionic and water ligands. In complex 2, the methyl group of one of the H3LEt ligands is disordered over two alternative orientations. Strong hydrogen bonds, both intra- and inter-molecular, are found in the crystal structures due to the number of different donor and acceptor groups present.

  20. Caracterización de la capa de boruros formada durante la austenización de un hierro nodular austemperizado//Characterization of borides coating formed during austenitization of an austempered ductile iron

    Directory of Open Access Journals (Sweden)

    Urbano Ordóñez‐Hernández

    2015-01-01

    Full Text Available En este trabajo se ha investigado el efecto de la austenitización y el borurado simultáneos, a 950 ºC, en la microestructura, la microdureza Vickers y el espesor de la capa borurada en medio líquido de un hierro nodular austemperizado no aleado. Se demostró que es posible obtener una capa de boruros de hierro muy bien estructurada con la microdureza Vickers suficientemente alta (1400 HVy con adecuado espesor de capa de 67 μm, sobre un sustrato de ausferrita típico de las fundiciones nodulares austemperizadas. Por medio de un ensayo pin on disc modificado, se comprobó la superior resistencia al desgaste abrasivo de la capa de boruros depositada durante la austenización del ADI, comparada con la máxima obtenida durante el austempering de éste sin aplicar el recubrimiento.Palabras claves: hierro nodular, borurado, austenización, austemperizado.______________________________________________________________________________AbstractThe effect of simultaneous austenitization and boriding at 950 ºC, on microstructure, Vickers hardness and boronized layer thickness of a non alloyed austempered ductile iron has been investigated. It was demonstrated that it is possible to obtain a well formed boronized layer with a Vicker hardness sufficiently high (1400 HV, and with an appropriated 67μm layer thickness, on a typical ausferrite ADI substrate. By using a modified pin on disc test, it was demonstrated the higher abrasion wear resistance of borides layer deposited during ADI austenitization process, compared with Vickers hardness of low temperature noncoated austempered ductile iron.Key words: ductile iron, boriding, austenitization, austempering.

  1. Comportamiento parabólico del crecimiento de capas boradas en los aceros Y8A y X12M // Parabolic behavior of boriding layers growth in Y8A and X12M steels

    Directory of Open Access Journals (Sweden)

    C. Figueroa Hernández

    1999-01-01

    Full Text Available Se determina la influencia que tienen los principales parámetros tecnológicos del borado en el crecimiento de las capas y secorrobora el cumplimiento de la ley parabólica para predecir este comportamiento en los aceros Y8A y X12M.El proceso de borado se aplica en una mezcla de carburo de silicio y bórax (70 y 30 % a la temperatura de 850, 900 y 950 oCdurante un tiempo de 2, 4 y 6 horas. Como variable dependiente se seleccionó la profundidad del recubrimiento, a partir de lacual se obtuvieron los coeficientes del crecimiento parabólico y la energía de activación en función de la temperatura, el tiempodel proceso y el tipo de acero.La caracterización metalográfica reveló la presencia de la fase Fe2BPalabras claves: Borado, recubrimiento superf icial , t ecnología de recubrimiento.__________________________________________________________________________AbstractIt was determined the influence of the main technological parameters of the boriding process, and a mathematical model thatallows to predict this conduct on the steels Y8A and X12M steels was obtained.The boriding process is applied in a mixture of silicon carbide and borax (70 and 30% at 850, 900 and 950 oC temperatureduring a period of time 2, 4 and 6 hours. As an independent variable the depth of the coat was selected.It was obtained the parabolic growth coefficients, and the activation energy according to temperature, time and the chemicalcomposition of steel.Metallografic analysis reveals the presence of Fe2B phase.Key words: Boriding process, superf icial coat , coat technology.

  2. History of ``NANO''-Scale VERY EARLY Solid-State (and Liquid-State) Physics/Chemistry/Metallurgy/ Ceramics; Interstitial-Alloys Carbides/Nitrides/Borides/...Powders and Cermets, Rock Shocks, ...

    Science.gov (United States)

    Maiden, Colin; Siegel, Edward

    History of ``NANO'': Siegel-Matsubara-Vest-Gregson[Mtls. Sci. and Eng. 8, 6, 323(`71); Physica Status Solidi (a)11,45(`72)] VERY EARLY carbides/nitrides/borides powders/cermets solid-state physics/chemistry/metallurgy/ ceramics FIRST-EVER EXPERIMENTAL NANO-physics/chemistry[1968 ->Physica Status Solidi (a)11,45(`72); and EARLY NANO-``physics''/NANO-``chemistry'' THEORY(after: Kubo(`62)-Matsubara(`60s-`70s)-Fulde (`65) [ref.: Sugano[Microcluster-Physics, Springer('82 `98)

  3. Synthesis, characterization and thermoelectric properties of metal borides, boron carbides and carbaborides; Synthese, Charakterisierung und thermoelektrische Eigenschaften ausgewaehlter Metallboride, Borcarbide und Carbaboride

    Energy Technology Data Exchange (ETDEWEB)

    Guersoy, Murat

    2015-07-06

    This work reports on the solid state synthesis and structural and thermoelectrical characterization of hexaborides (CaB{sub 6}, SrB{sub 6}, BaB{sub 6}, EuB{sub 6}), diboride dicarbides (CeB{sub 2}C{sub 2}, LaB{sub 2}C{sub 2}), a carbaboride (NaB{sub 5}C) and composites of boron carbide. The characterization was performed by X-ray diffraction methods and Rietveld refinements based on structure models from literature. Most of the compounds were densified by spark plasma sintering at 100 MPa. As high-temperature thermoelectric properties the Seebeck coefficients, electrical conductivities, thermal diffusivities and heat capacities were measured between room temperature and 1073 K. ZT values as high as 0.5 at 1273 K were obtained for n-type conducting EuB{sub 6}. High-temperature X-ray diffraction also confirmed its thermal stability. The solid solutions Ca{sub x}Sr{sub 1-x}B{sub 6}, Ca{sub x}Ba{sub 1-x}B{sub 6} and Sr{sub x}Ba{sub 1-x}B{sub 6} (x = 0, 0.25, 0.5, 0.75, 1) are also n-type but did not show better ZT values for the ternary compounds compared to the binaries, but for CaB{sub 6} the values of the figure of merit (ca. 0.3 at 1073 K) were significantly increased (ca. 50 %) compared to earlier investigations which is attributed to the densification process. Sodium carbaboride, NaB{sub 5}C, was found to be the first p-type thermoelectric material that crystallizes with the hexaboride-structure type. Seebeck coefficients of ca. 80 μV . K{sup -1} were obtained. Cerium diboride dicarbide, CeB{sub 2}C{sub 2}, and lanthanum diboride dicarbide, LaB{sub 2}C{sub 2}, are metallic. Both compounds were used as model compounds to develop compacting strategies for such layered borides. Densities obtained at 50 MPa were determined to be higher than 90 %. A new synthesis route using single source precursors that contain boron and carbon was developed to open the access to new metal-doped boron carbides. It was possible to obtain boron carbide, but metal-doping could not be

  4. Synthesis and characterization of new metal-rich borides with boron fragments; Synthese und Charakterisierung von neuartigen metallreichen Boriden mit Borfragmenten

    Energy Technology Data Exchange (ETDEWEB)

    Mbarki, Mohammed

    2016-03-30

    The present dissertation deals with the synthesis and characterization of new metal-rich borides of the Ce{sub 7}Ni{sub 5±x}Ge{sub 3±x}In{sub 6{sup -}}, Nb{sub 2}OsB{sub 2{sup -}} and NbRuB-type.The samples are synthesized by a solid state reaction route from elements using an electric arc furnace. The structural characterization of the compounds was carried out by using X-ray diffraction methods on powder samples and single crystals. The chemical composition of single-crystals was verified by EDX analyses. Moreover, the magnetic properties of suitable samples were investigated by SQUID magnetometry.The crystal structure of compounds with the nominal composition NbFe{sub 1-x}Ir{sub 6+x}B{sub 8} is successfully solved from single crystal X-ray data. The most prominent feature in this structure are one-dimensional chains along the c-axis formed by the magnetically active element iron on a site of mixed occupation with Iridium (Fe: Ir = 0.77 (2) 0.23 (2)). Thermomagnetic investigations reveal, that ferromagnetic ordering is observed below the Curie temperature (TC) of 350 K. Theoretical investigations suggest that the iron-chains are mainly responsible for the ferromagnetic ordering. In addition, the magnetocaloric effect (MCE) is calculated using isothermal magnetization measurements at several temperatures. The maximal magnetic entropy change ΔS = 0.032 J kg{sup -1} K{sup -1} is observed in the vicinity of T{sub C}. For the phases Nb{sub 6}Mn{sub 0,75(2)}Ir{sub 6,25(2)}B{sub 8} and Nb{sub 6}Co{sub 1,09(2)}Ir{sub 5,91(2)}B{sub 8} a relationship between the measured ferrimagnetic ordering and the crystal structure is found. Tiny superstructure reflections measured by Selected Area Electron Diffraction (SEAD) indicate a different crystal system for those compounds, which allows a ferrimagnetic spin arrangement within this crystal structure.In the second part of the thesis new results about the Nb{sub 2}OsB{sub 2-} and NbRuB-type borides are presented, which both

  5. The response behavior of PPy-DB18C6 electrode to terbium(III in acetonitrile and its thermodynamic application

    Directory of Open Access Journals (Sweden)

    Mohammad Hossein Arbab Zavar

    2016-11-01

    Full Text Available Polypyrrole modified electrode prepared by electropolymerization of pyrrole in the presence of a complexing ligand, dibenzo-18-crown-6(DB18C6, was prepared and investigated as a Tb3+-selective electrode in acetonitrile. The potentiometric response of the electrode was linear within the Tb3+ concentration range 1 × 10−5–1 × 10−2 M with a Nernstian slope of 20.9 mVdecade−1 in AN. The electrode was applied to study the complexation of the terbium(III ion in acetonitrile with such other basic aprotic solvent molecules (D as dimethyl sulfoxide, N,N-dimethyl formamide, propylene carbonate and pyridine. The successive complex formation constant (βi and Gibbs energies of transfer (ΔGtr of Tb3+ in AN in relation to such D were obtained.

  6. Luminescence and Magnetic Properties of Two Three-Dimensional Terbium and Dysprosium MOFs Based on Azobenzene-4,4′-Dicarboxylic Linker

    Directory of Open Access Journals (Sweden)

    Belén Fernández

    2016-02-01

    Full Text Available We report the in situ formation of two novel metal-organic frameworks based on terbium and dysprosium ions using azobenzene-4,4′-dicarboxylic acid (H2abd as ligand, synthesized by soft hydrothermal routes. Both materials show isostructural three-dimensional networks with channels along a axis and display intense photoluminescence properties in the solid state at room temperature. Textural properties of the metal-organic frameworks (MOFs have been fully characterized although no appreciable porosity was obtained. Magnetic properties of these materials were studied, highlighting the dysprosium material displays slightly frequency-dependent out of phase signals when measured under zero external field and under an applied field of 1000 Oe.

  7. The studies on complex formation of metal borides in the reaction system of epoxidation of 1-octene with tert-butyl hydroperoxide by IR spectroscopy

    OpenAIRE

    Makota, Oksana; Trach, Yuriy

    2007-01-01

    Вивчено комплексоутворення боридів молібдену і ванадію в реакційній системі епоксидування октену-1 гідропероксидом трет-бутилу методом інфрачервоної спектроскопії. Показано, що октен-1 утворює комплекс з металевою складовою у випадку бориду молібдену і з боридною складовою у випадку бориду ванадію.The complex formation of molybdenum and vanadium borides in the reaction system of 1-octene epoxidation with tert -butyl hydroperoxide by infrared spectroscopic analysis was studied. It was sh...

  8. Luminescent europium and terbium complexes of dipyridoquinoxaline and dipyridophenazine ligands as photosensitizing antennae: structures and biological perspectives.

    Science.gov (United States)

    Dasari, Srikanth; Patra, Ashis K

    2015-12-14

    The europium(III) and terbium(III) complexes, namely [Eu(dpq)(DMF)2(NO3)3] (1), [Eu(dppz)2(NO3)3] (2), [Tb(dpq)(DMF)2Cl3] (3), and [Tb(dppz)(DMF)2Cl3] (4), where dipyrido[3,2-d:2',3'-f]quinoxaline (dpq in 1 and 3), dipyrido[3,2-a:2',3'-c]phenazine (dppz in 2 and 4) and N,N'-dimethylformamide (DMF) have been isolated, characterized from their physicochemical data, luminescence studies and their interaction with DNA, serum albumin protein and photo-induced DNA cleavage activity are studied. The X-ray crystal structures of complexes 1-4 show discrete mononuclear Ln(3+)-based structures. The Eu(3+) in [Eu(dpq)(DMF)2(NO3)3] (1) and [Eu(dppz)2(NO3)3] (2) as [Eu(dppz)2(NO3)3]·dppz (2a) adopts a ten-coordinated bicapped dodecahedron structure with a bidentate N,N-donor dpq ligand, two DMF and three NO3(-) anions in 1 and two bidentate N,N-donor dppz ligands and three NO3(-) anions in 2. Complexes 3 and 4 show a seven-coordinated mono-capped octahedron structure where Tb(3+) contains bidentate dpq/dppz ligands, two DMF and three Cl(-) anions. The complexes are highly luminescent in nature indicating efficient photo-excited energy transfer from the dpq/dppz antenna to Ln(3+) to generate long-lived emissive excited states for characteristic f → f transitions. The time-resolved luminescence spectra of complexes 1-4 show typical narrow emission bands attributed to the (5)D0 → (7)F(J) and (5)D4 → (7)F(J) f-f transitions of Eu(3+) and Tb(3+) ions respectively. The number of inner-sphere water molecules (q) was determined from luminescence lifetime measurements in H2O and D2O confirming ligand-exchange reactions with water in solution. The complexes display significant binding propensity to the CT-DNA giving binding constant values in the range of 1.0 × 10(4)-6.1 × 10(4) M(-1) in the order 2, 4 (dppz) > 1, 3 (dpq). DNA binding data suggest DNA groove binding with the partial intercalation nature of the complexes. All the complexes also show binding propensity (K(BSA)

  9. Spin Waves in Terbium

    DEFF Research Database (Denmark)

    Jensen, J.; Houmann, Jens Christian Gylden

    1975-01-01

    The selection rules for the linear couplings between magnons and phonons propagating in the c direction of a simple basal-plane hcp ferromagnet are determined by general symmetry considerations. The acoustic-optical magnon-phonon interactions observed in the heavy-rare-earth metals have been expl...... by Liu. The coupled magnon—transverse-phonon system for the c direction of Tb is analyzed in detail, and the strengths of the couplings are deduced as a function of wave vector by combining the experimental studies with the theory....

  10. Spin Waves in Terbium

    DEFF Research Database (Denmark)

    Jensen, J.; Houmann, Jens Christian Gylden; Bjerrum Møller, Hans

    1975-01-01

    The energies of spin waves propagating in the c direction of Tb have been studied by inelastic neutron scattering, as a function of a magnetic field applied along the easy and hard directions in the basal plane, and as a function of temperature. From a general spin Hamiltonian, consistent...... with the symmetry, we deduce the dispersion relation for the spin waves in a basal-plane ferromagnet. This phenomenological spin-wave theory accounts for the observed behavior of the magnon energies in Tb. The two q⃗-dependent Bogoliubov components of the magnon energies are derived from the experimental results...

  11. ScRu2B3 and Sc2RuB6: Borides Featuring a 2D Infinite Boron Clustering.

    Science.gov (United States)

    Salamakha, Leonid P; Sologub, Oksana; Stöger, Berthold; Rogl, Peter Franz; Waas, Monika; Kapustianyk, Volodymyr B; Bauer, Ernst

    2017-09-05

    Two borides, ScRu2B3 and Sc2RuB6, were obtained by argon-arc melting of the elements followed by annealing at 800 °C. ScRu2B3 exhibits a new structure type with the space group Cmcm (a = 3.0195(2) Å, b = 15.4056(8) Å, c = 5.4492(3) Å; single crystal X-ray data; RF(2) = 0.0105). Sc2RuB6 adopts the Y2ReB6-type structure (space group Pbam; a = 8.8545(2) Å, b = 11.1620(3) Å, c = 3.4760(1) Å; single crystal X-ray data; RF(2) = 0.0185). ScRu2B3 displays an unusual intergrowth of CeCo3B2- and AlB2-related slabs; a striking feature is a boat configuration of puckered boron hexagons within infinite graphite like boron layers (6(3) nets). Sc2RuB6 presents two-dimensional planar nets of condensed boron pentagons, hexagons, and heptagons sandwiched between metal layers. In Sc/Y substituted Y2ReB6-type, Y atoms are distributed exclusively inside the boron heptagons. Exploration of the Sc-Ru-B system at 800 °C including binary boundaries employing EPMA and powder X-ray diffraction technique furthermore rules out the existence of previously reported "ScRuB4" but confirms the formation and crystal structure of Sc2Ru5B4. ScRu4B4 forms in cast alloys (LuRu4B4-type structure; space group I41/acd (No. 142), a = 7.3543(2) Å, c = 14.92137(8) Å). Cell parameters and atomic coordinates have been refined for ScRu2B3, Sc2RuB6, and ScRu4B4 in the scope of the generalized gradient approximation. Ab initio electronic structure calculations indicate a moderate electronic density of states at the Fermi level situated near the upper edge of essentially filled d-bands. Electrical resistivity measurements characterize ScRu2B3 and Sc2RuB6 as metals in concord with electronic band structure calculations.

  12. Synthesis and crystal structure of terbium(III) meta-oxoborate Tb(BO{sub 2}){sub 3} ({identical_to} TbB{sub 3}O{sub 6}); Synthese und Kristallstruktur von Terbium(III)-meta-Oxoborat Tb(BO{sub 2}){sub 3} ({identical_to} TbB{sub 3}O{sub 6})

    Energy Technology Data Exchange (ETDEWEB)

    Nikelski, Tanja; Schleid, Thomas [Institut fuer Anorganische Chemie der Universitaet Stuttgart (Germany)

    2003-06-01

    The terbium meta-oxoborate Tb(BO{sub 2}){sub 3} ({identical_to} TbB{sub 3}O{sub 6}) is obtained as single crystals by the reaction of terbium, Tb{sub 4}O{sub 7} and TbCl{sub 3} with an excess of B{sub 2}O{sub 3} in gastight sealed platinum ampoules at 950 C after three weeks. The compound appears to be air- and water-resistant and crystallizes as long, thin, colourless needles which tend to growth-twinning due to their marked fibrous habit. The crystal structure of Tb(BO{sub 2}){sub 3} (orthorhombic, Pnma; a = 1598.97(9), b = 741.39(4), c = 1229.58(7) pm; Z = 16) contains strongly corrugated oxoborate layers {sub {infinity}}{sup 2}{l_brace}(BO{sub 2}){sup -}{r_brace} built of vertex-linked [BO{sub 4}]{sup 5-} tetrahedra (d(B-O) = 143 - 154 pm, and angsph;(O-B-O) = 102-115 ) which spread out parallel (100). The four crystallographically different Tb{sup 3+} cations all exhibit coordination numbers of eight towards the oxygen atoms (d(Tb-O) = 228-287 pm). The corresponding metal cation polyhedra [TbO{sub 8}]{sup 13+} too convene to layers (composition: {sub {infinity}}{sup 2}{l_brace}(Tb{sub 2}O{sub 11}){sup 16-}{r_brace}) which are likewise oriented parallel to the (100) plane. (Abstract Copyright [2003], Wiley Periodicals, Inc.) [German] Das Terbium-meta-Oxoborat Tb(BO{sub 2}){sub 3} ({identical_to} TbB{sub 3}O{sub 6}) entsteht einkristallin bei der Reaktion von Terbium, Tb{sub 4}O{sub 7} und TbCl{sub 3} mit einem Ueberschuss von B{sub 2}O{sub 3} in gasdicht verschlossenen Platinampullen nach drei Wochen bei 950 C. Die Verbindung ist luft- und wasserstabil und faellt in langen, duennen, farblosen Nadeln an, die aufgrund ihres ausgepraegt faserigen Habitus zur Wachstumsverzwillingung neigen. Die Kristallstruktur von Tb(BO{sub 2}){sub 3} (orthorhombisch, Pnma; a = 1598, 97(9), b = 741, 39(4), c = 1229, 58(7) pm; Z = 16) enthaelt parallel (100) verlaufende, stark gewellte Oxoborat-Schichten {sub {infinity}}{sup 2}{l_brace}(BO{sub 2}){sup -}{r_brace} aus

  13. An integrated logic system for time-resolved fluorescent "turn-on" detection of cysteine and histidine base on terbium (III) coordination polymer-copper (II) ensemble.

    Science.gov (United States)

    Xue, Shi-Fan; Lu, Ling-Fei; Wang, Qi-Xian; Zhang, Shengqiang; Zhang, Min; Shi, Guoyue

    2016-09-01

    Cysteine (Cys) and histidine (His) both play indispensable roles in many important biological activities. An enhanced Cys level can result in Alzheimer's and cardiovascular diseases. Likewise, His plays a significant role in the growth and repair of tissues as well as in controlling the transmission of metal elements in biological bases. Therefore, it is meaningful to detect Cys and His simultaneously. In this work, a novel terbium (III) coordination polymer-Cu (II) ensemble (Tb(3+)/GMP-Cu(2+)) was proposed. Guanosine monophosphate (GMP) can self-assemble with Tb(3+) to form a supramolecular Tb(3+) coordination polymer (Tb(3+)/GMP), which can be suited as a time-resolved probe. The fluorescence of Tb(3+)/GMP would be quenched upon the addition of Cu(2+), and then the fluorescence of the as-prepared Tb(3+)/GMP-Cu(2+) ensemble would be restored again in the presence of Cys or His. By incorporating N-Ethylmaleimide and Ni(2+) as masking agents, Tb(3+)/GMP-Cu(2+) was further exploited as an integrated logic system and a specific time-resolved fluorescent "turn-on" assay for simultaneously sensing His and Cys was designed. Meanwhile it can also be used in plasma samples, showing great potential to meet the need of practical application. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. Synthesis and photoluminescence properties of cerium-doped terbium-yttrium aluminum garnet phosphor for white light-emitting diodes applications

    Science.gov (United States)

    Wang, Jun; Han, Tao; Lang, Tianchun; Tu, Mingjing; Peng, Lingling

    2015-11-01

    Cerium-doped terbium-yttrium aluminum garnet phosphors were synthesized using the solid-state reaction method. The crystalline phase, morphology, and photoluminescence properties were characterized by x-ray diffraction (XRD), scanning electron microscope (SEM), and fluorescence spectrophotometer, respectively. The XRD results indicate that with an increase of the amount of x (Tb3+), all of the samples have a pure garnet crystal structure without secondary phases. The SEM images reveal that the samples are composed of sphere-like crystallites, which exhibit different degrees of agglomeration. The luminescent properties of Ce ions in )Al5O12∶Ce0.1 have been studied, and it was found that the emission band shifted toward a longer wavelength. The redshift is attributed to the lowering of the 5d energy level centroid of Ce, which can be explained by the nephelauxetic effect and compression effect. These phosphors were coated on blue light-emitting diode (LED) chips to fabricate white light-emitting diodes (WLEDs), and their color-rendering indices, color temperatures, and luminous efficiencies were measured. As a consequence of the addition of Tb, the blue LED pumped )Al5O12∶Ce0.1 phosphors WLEDs showed good optical properties.

  15. Study on the fluorescent enhancement effect in terbium-gadolinium-protein-sodium dodecyl benzene sulfonate system and its application on sensitive detection of protein at nanogram level.

    Science.gov (United States)

    Sun, Changxia; Yang, Jinghe; Wu, Xia; Liu, Shufang; Su, Benyu

    2004-08-01

    The co-luminescence effect in a terbium-gadolinium-protein-sodium dodecyl benzene sulfonate (SDBS) system is reported here. Based on it, the sensitive quantitative analysis of protein at nanogram levels is established. The co-luminescence mechanism is studied using fluorescence, resonance light scattering (RLS), absorption spectroscopy and NMR measurement. It is considered that protein could be unfolded by SDBS, then a efficacious intramolecular fluorescent energy transfer occurs from unfolded protein to rare earth ions through SDBS acting as a "transfer bridge" to enhance the emission fluorescence of Tb3+ in this ternary complex of Tb-SDBS-BSA, where energy transfer from protein to SDBS by aromatic ring stacking is the most important step. Cooperating with the intramolecular energy transfer above is the intermolecular energy transfer between the simultaneous existing complexes of both Tb3+ and Gd3+. The fluorescence quantum yield is increased by an energy-insulating sheath, which is considered to be another reason for the resulting enhancement of the fluorescence. Förster theory is used to calculate the distribution of enhancing factors and has led to a greater understanding of the mechanisms of energy transfer.

  16. [Studies on luminescence properties of seven ternary complexes of terbium with 1,10-phenanthroline and benzoic acid and its derivatives].

    Science.gov (United States)

    Gao, Zhi-hua; Wang, Shu-ping; Liu, Cui-ge; Ma, Rui-xia; Wang, Rui-fen

    2006-04-01

    Seven ternary complexes of Tb(III) were synthesized with benzoic acid (BA), o-, m-, p-methylbenzoic acid (o-MBA, m-MBA, p-MBA), and o-, m-, p-methoxybenzoic acid (o-MOBA, m-MOBA, p-MOBA) as the first ligand, and 1,10-phenanthroline (phen) as the second ligand. The content of C, H and N were measured by using a Flash-EA model 1112 elemental analyzer. Excitation and luminescence spectra of the title solid complexes were recorded by using a Hitachi F-4500 fluorescence spectrophotometer at room temperature. The effects of different varieties and different positions of replacing benzoic acid as the first ligand on fluorescence properties of the ternary complexes of terbium were discussed. The results indicated that the intensity of 5D4-->7F6 (489 nm) and 5D4-->7F5 (545 nm) of substituting benzoic acid complexes was stronger than benzoic acid. Three ternary complexes of Tb(III) with o-, m-, p-methylbenzoic acid showed emission intensity in the consecution: Tb(o-MBA)3 phenMOBA)3phen x H2O>Tb(m-MOBA)3phen x H2O>Tb(p-MOBA)3 phen.

  17. First-principles study of structural stability, elastic and electronic properties of ternary rare earth-transition metal—Borides and carbides (RT{sub x}Z, R=Sc, Y, and La, T=Pt and Pd, Z=B and C, and x=2, 3, and 4)

    Energy Technology Data Exchange (ETDEWEB)

    Yao, Tiankai; Wang, Yachun; Li, Hui [Key Laboratory of Metastable Materials Science and Technology, College of Material Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Lian, Jie [Department of Mechanical, Aerospace and Nuclear Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Zhang, Jingwu, E-mail: zjw@ysu.edu.cn [Key Laboratory of Metastable Materials Science and Technology, College of Material Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Gou, Huiyang, E-mail: huiyang.gou@gmail.com [Key Laboratory of Metastable Materials Science and Technology, College of Material Science and Engineering, Yanshan University, Qinhuangdao 066004 (China)

    2013-12-15

    Using first-principles total energy calculations (CASTEP code), the structural stability, elastic, and electronic properties of ternary rare earth-transition metal borides and carbides (RT{sub x}Z, R=Sc, Y, and La, T=Pt and Pd, Z=B and C, and x=2, 3, and 4) compounds were studied. Results show that RT{sub 3}Z compounds with tetragonal P4mm structure are energetically more favorable than usually cubic perovskite-type structure. Furthermore, RT{sub 3}Z with perovskite structure is found to be mechanically unstable with the negative C{sub 44}. Formation enthalpy calculations indicate that Pt-based borides are easier to be synthesized compared with Pd-based ones and counterpart carbides, respectively. Elastic constants, bulk moduli, shear moduli, Young's moduli, and Poisson's ratio of studied compounds have been calculated. Also, all the studied compounds show ductile behavior. Moreover, total and partial density of states (DOSs) and bonding charge density were employed to elucidate the bonding features of these compounds. The results reveal that the covalency between Pt-5d and Z-2p as well as T-nd (n=4 for Pd and 5 for Pt) and B-2p states, are the cause of the relatively higher elastic moduli of Pt-based compounds and R–T-borides, respectively.

  18. Self-diffusion coefficients of the trivalent f-element ion series in dilute and moderately dilute aqueous solutions: A comparative study between europium, gadolinium, terbium and berkelium

    Science.gov (United States)

    Rafik, Besbes; Noureddine, Ouerfelli; Abderabbou, Abdelmanef; Habib, Latrous

    2010-03-01

    We have continued the studies on the trivalent ions of the 4f and 5f elements. In this paper, we compare the transport properties (self-diffusion coefficient) of the trivalent aquo ions over two ranges of concentrations (0 — 2×10-3M) and (2×10-3 — 1.5M). Self-diffusion coefficients, D, of the trivalent f-element aquo ion series have been determined in aqueous background electrolytes of Gd(NO3)3 and Nd(ClO4)3, at pH=2.5 (HNO3, HClO4) and at 25°C using the open-end capillary method (O.E.C.M.). This method measures the transportation time of ions across a fixed distance. In this paper, we complete a measurement of self-diffusion coefficient for terbium. We optimized the pH to avoid hydrolysis, ion-pairing and complexation of the trivalent 4f and 5f ions. The variation of D versus √C is not linear for dilute solutions (0 — 2×10-3M) and quasi-linear in moderate concentrations (C<=1.5 M). Similar behavior was observed for Tb, as compared with those for Bk, Eu and Gd. We complete the comparison variation of D/D° versus √C for all studied 4f and 5f elements from concentration 0 to 1.5M and we obtained the same variation with √C for all studied elements. All 4f and 5f elements studied follow the Nernst-Hartley expression.

  19. Terbium-based time-gated Förster resonance energy transfer imaging for evaluating protein-protein interactions on cell membranes.

    Science.gov (United States)

    Lindén, Stina; Singh, Manish Kumar; Wegner, K David; Regairaz, Marie; Dautry, François; Treussart, François; Hildebrandt, Niko

    2015-03-21

    Fluorescence imaging of cells and subcellular compartments is an essential tool to investigate biological processes and to evaluate the development and progression of diseases. In particular, protein-protein interactions can be monitored by Förster resonance energy transfer (FRET) between two proximal fluorophores that are attached to specific recognition biomolecules such as antibodies. We investigated the membrane expression of E- and N-cadherins in three different cell lines used as model systems to study epithelial to mesenchymal transition (EMT) and a possible detection of circulating tumour cells (CTCs). EMT is a key process in cancer metastasis, during which epithelial markers (such as E-cadherin) are down-regulated in the primary tumour whereas mesenchymal markers (such as N-cadherin) are up-regulated, leading to enhanced cell motility, intravasation, and appearance of CTCs. Various FRET donor-acceptor pairs and protein recognition strategies were utilized, in which Lumi4-Tb terbium complexes (Tb) and different organic dyes were conjugated to several distinct E- and N-cadherin-specific antibodies. Pulsed excitation of Tb at low repetition rates (100 Hz) and time-gated (TG) imaging of both the Tb-donor and the dye-acceptor photoluminescence (PL) allowed efficient detection of the EMT markers as well as FRET in the case of sufficient donor-acceptor proximity. Efficient FRET was observed only between two E-cadherin-specific antibodies and further experiments indicated that these antibodies recognized the same E-cadherin molecule, suggesting a limited accessibility of cadherins when they are clustered at adherens junctions. The investigated Tb-to-dye FRET systems provided reduced photobleaching compared to the AlexaFluor 488-568 donor-acceptor pair. Our results demonstrate the applicability and advantages of Tb-based TG FRET for efficient and stable imaging of antibody-antibody interactions on different cell lines. They also reveal the limitations of

  20. A broad G protein-coupled receptor internalization assay that combines SNAP-tag labeling, diffusion-enhanced resonance energy transfer, and a highly emissive terbium cryptate acceptor

    Directory of Open Access Journals (Sweden)

    Angélique eLEVOYE

    2015-11-01

    Full Text Available Although G protein-coupled receptor (GPCR internalization has long been considered a major aspect of the desensitization process that tunes ligand responsiveness, internalization is also involved in receptor resensitization and signaling, as well as the ligand scavenging function of some atypical receptors. Internalization thus contributes to the diversity of GPCR-dependent signaling, and its dynamics and quantification in living cells has generated considerable interest. We developed a robust and sensitive assay to follow and quantify ligand-induced and constitutive GPCR internalization but also receptor recycling in living cells. This assay is based on diffusion-enhanced resonance energy transfer (DERET between cell surface GPCRs labeled with a luminescent terbium cryptate donor and a fluorescein acceptor present in the culture medium. GPCR internalization results in a quantifiable reduction of energy transfer. This method yields a high signal-to-noise ratio due to time-resolved measurements. For various GPCRs belonging to different classes, we demonstrated that constitutive and ligand-induced internalization could be monitored as a function of time and ligand concentration, thus allowing accurate quantitative determination of kinetics of receptor internalization but also half-maximal effective or inhibitory concentrations of compounds. In addition to its selectivity and sensitivity, we provided evidence that DERET-based internalization assay is particularly suitable for characterizing biased ligands. Furthermore, the determination of a Z’-factor value of 0.45 indicates the quality and suitability of DERET-based internalization assay for high-throughput screening (HTS of compounds that may modulate GPCRs internalization.

  1. Crystal structure of an eight-coordinate terbium(III ion chelated by N,N′-bis(2-hydroxybenzyl-N,N′-bis(pyridin-2-ylmethylethylenediamine (bbpen2− and nitrate

    Directory of Open Access Journals (Sweden)

    Thaiane Gregório

    2015-01-01

    Full Text Available The reaction of terbium(III nitrate pentahydrate in acetonitrile with N,N′-bis(2-hydroxybenzyl-N,N′-bis(pyridin-2-ylmethylethylenediamine (H2bbpen, previously deprotonated with triethylamine, produced the mononuclear compound [N,N′-bis(2-oxidobenzyl-κO-N,N′-bis(pyridin-2-ylmethyl-κNethylenediamine-κ2N,N′](nitrato-κ2O,O′terbium(III, [Tb(C28H28N4O2(NO3]. The molecule lies on a twofold rotation axis and the TbIII ion is eight-coordinate with a slightly distorted dodecahedral coordination geometry. In the symmetry-unique part of the molecule, the pyridine and benzene rings are both essentially planar and form a dihedral angle of 61.42 (7°. In the molecular structure, the N4O4 coordination environment is defined by the hexadentate bbpen ligand and the bidentate nitrate anion. In the crystal, a weak C—H...O hydrogen bond links molecules into a two-dimensional network parallel to (001.

  2. Crystal Growth, Structures, and Properties of the Complex Borides, LaOs 2 Al 2 B and La 2 Os 2 AlB 2

    Energy Technology Data Exchange (ETDEWEB)

    Bugaris, Daniel E.; Han, Fei; Im, Jino; Chung, Duck Young; Freeman, Arthur J.; Kanatzidis, Mercouri G.

    2015-08-17

    Single crystals of two novel quaternary metal borides, LaOs2Al2B and La2Os2AlB2, have been grown from La/Ni eutectic fluxes. LaOs2Al2B crystallizes in tetragonal space group P4/mmm with the CeCr2Si2C-type structure, and lattice parameters a = 4.2075(6) angstrom and c = 5.634(1) angstrom. La2Os2AlB2 exhibits a new crystal structure in monoclinic space group C2/c with lattice parameters a = 16.629(3) angstrom, b = 6.048(1) angstrom, c = 10.393(2) angstrom, and beta = 113.96(3)degrees. Both structures are three-dimensional frameworks with unusual coordination (for solid-state compounds) of the boron atoms by transition metal atoms. The boron atom is square planar in LaOs2Al2B, whereas it exhibits linear and T-shaped geometries in La2Os2AlB2. Electrical resistivity measurements reveal poor metal behavior (rho(30)0 (K) similar to 900 mu Omega cm) for La2Os2AlB2, consistent with the electronic band structure calculations, which also predict a metallic character for LaOs2Al2B.

  3. Selective Sensing of Fe(3+) and Al(3+) Ions and Detection of 2,4,6-Trinitrophenol by a Water-Stable Terbium-Based Metal-Organic Framework.

    Science.gov (United States)

    Cao, Li-Hui; Shi, Fang; Zhang, Wen-Min; Zang, Shuang-Quan; Mak, Thomas C W

    2015-10-26

    A water-stable luminescent terbium-based metal-organic framework (MOF), {[Tb(L1 )1.5 (H2 O)]⋅3 H2 O}n (Tb-MOF), with rod-shaped secondary building units (SBUs) and honeycomb-type tubular channels has been synthesized and structurally characterized by single-crystal X-ray diffraction. The high green emission intensity and the microporous nature of the Tb-MOF indicate that it can potentially be used as a luminescent sensor. In this work, we show that Tb-MOF can selectively sense Fe(3+) and Al(3+) ions from mixed metal ions in water through different detection mechanisms. In addition, it also exhibits high sensitivity for 2,4,6-trinitrophenol (TNP) in the presence of other nitro aromatic compounds in aqueous solution by luminescence quenching experiments. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Picomolar traces of americium(III) introduce drastic changes in the structural chemistry of terbium(III). A break in the ''gadolinium break''

    Energy Technology Data Exchange (ETDEWEB)

    Welch, Jan M. [TU Wien, Atominstitut, Vienna (Austria); Mueller, Danny; Knoll, Christian; Wilkovitsch, Martin; Weinberger, Peter [TU Wien, Institute of Applied Synthetic Chemistry, Vienna (Austria); Giester, Gerald [University of Vienna, Institute of Mineralogy and Crystallography, Vienna (Austria); Ofner, Johannes; Lendl, Bernhard [TU Wien, Institute of Chemical Technologies and Analytics, Vienna (Austria); Steinhauser, Georg [Leibniz Universitaet Hannover, Institute of Radioecology and Radiation Protection (Germany)

    2017-10-16

    The crystallization of terbium 5,5{sup '}-azobis[1H-tetrazol-1-ide] (ZT) in the presence of trace amounts (ca. 50 Bq, ca. 1.6 pmol) of americium results in 1) the accumulation of the americium tracer in the crystalline solid and 2) a material that adopts a different crystal structure to that formed in the absence of americium. Americium-doped [Tb(Am)(H{sub 2}O){sub 7}ZT]{sub 2} ZT.10 H{sub 2}O is isostructural to light lanthanide (Ce-Gd) 5,5{sup '}-azobis[1H-tetrazol-1-ide] compounds, rather than to the heavy lanthanide (Tb-Lu) 5,5{sup '}-azobis[1H-tetrazol-1-ide] (e.g., [Tb(H{sub 2}O){sub 8}]{sub 2}ZT{sub 3}.6 H{sub 2}O) derivatives. Traces of Am seem to force the Tb compound into a structure normally preferred by the lighter lanthanides, despite a 10{sup 8}-fold Tb excess. The americium-doped material was studied by single-crystal X-ray diffraction, vibrational spectroscopy, radiochemical neutron activation analysis, and scanning electron microscopy. In addition, the inclusion properties of terbium 5,5{sup '}-azobis[1H-tetrazol-1-ide] towards americium were quantified, and a model for the crystallization process is proposed. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  5. Sodium terbium(III polyphosphate

    Directory of Open Access Journals (Sweden)

    Abdelghani Oudahmane

    2010-04-01

    Full Text Available Single crystals of the title compound, NaTb(PO34, were obtained by solid-state reaction. This compound belongs to type II of long-chain polyphosphates with the general formula AIBIII(PO34. It is isotypic with the NaNd(PO34 and NaEr(PO34 homologues. The crystal structure is built up of infinite crenelated chains of corner-sharing PO4 tetrahedra with a repeating unit of four tetrahedra. These chains, extending parallel to [100], are linked by isolated TbO8 square antiprisms, forming a three-dimensional framework. The Na+ ions are located in channels running along [010] and are surrounded by six oxygen atoms in a distorted octahedral environment within a cut-off distance <2.9 Å.

  6. Computer Modeling of Ceramic Boride Composites

    Science.gov (United States)

    2014-11-01

    coefficients of thermal expansion. Approximately linear expansion coefficient of the composite is determined by the relation [52] EEE BBBAAAk...1 δαδαα ⋅+⋅= , (58) where AE and BE are Young moduli of components, and E – average modulus for composition BBAA EEE δδ

  7. Magnesium Aluminum Borides as Explosive Materials

    Science.gov (United States)

    2011-12-20

    Dryer , H. Rabitz, R. C. Brown, and C. E. Kolb, “Effect of Fluorine on the Combustion of “Clean” Surface Boron Particles,” Combustion and Flame, 112 507...521 (1998). 71. W. Zhou, R. A. Yetter, F. L. Dryer , H. Rabitz, R. C. Brown, and C. E. Kolb, “A Comprehensive Physical and Numerical Model of Boron...251-257 (1970). 114. T. Abu-Hamed, J. Karni, and M. Epstein, “The Use of Boron for Thermochemical Storage and Distribution of Solar Energy,” Solar

  8. A europium- and terbium-coated magnetic nanocomposite as sorbent in dispersive solid phase extraction coupled with ultra-high performance liquid chromatography for antibiotic determination in meat samples.

    Science.gov (United States)

    Castillo-García, M L; Aguilar-Caballos, M P; Gómez-Hens, A

    2015-12-18

    A new magnetic dispersive solid-phase extraction approach based on Eu- and Tb-coated magnetic nanocomposites, combined with ultra-high performance liquid chromatography with fluorometric detection, is reported for the extraction and simultaneous determination of veterinary antibiotics. The method is aimed at monitoring of potential residues of three tetracyclines, namely oxytetracycline, tetracycline, chlortetracycline and three acidic quinolones, such as oxolinic acid, nalidixic acid and flumequine, chosen as model analytes, in animal muscle samples. The nanocomposites were obtained by synthesizing magnetic nanoparticles by a co-precipitation method and their coating with terbium and europium ions. The limits of detection obtained using standard solutions were: 1.0, 1.5, 3.8, 0.25, 0.7 and 1.2ngmL(-1), which corresponds to 3.3, 5.0, 12.7, 0.8, 2.3 and 4.0μgkg(-1) for oxytetracycline, tetracycline, chlortetracycline, oxolinic acid, nalidixic acid and flumequine, respectively, in meat samples. The precision values, obtained in the presence of the sample matrix, were in the ranges 0.12-2.0% and 2.6-15.4% for retention times and areas, respectively. The selectivity of the method was checked by assaying different veterinary drugs, finding that most of them did not interfere at the same concentration levels as that of analytes. A recovery study was performed in the presence of chicken and pork muscle samples, which provided values in the range of 61.5-102.6%. Copyright © 2015 Elsevier B.V. All rights reserved.

  9. Spectroscopic analysis of lithium terbium tetrafluoride

    DEFF Research Database (Denmark)

    Christensen, H.P.

    1978-01-01

    . The rare-earth site in LiTbF4 possesses S4 symmetry, which allows six crystal-field parameters. ζ and the six Bim were varied to obtain the best agreement with the experimentally observed levels. Keeping F2=434 cm-1 fixed, a fit with a standard deviation of 12 cm-1 was obtained at 10 K with the following...... were calculated by diagonalizing an effective spin-orbit and crystal-field Hamiltonian in an LS basis. H=Σλi(L→·S→)i+ΣαiΣBimOim, where the parameters λi are functions of the spin-orbit parameter ζ and the Slater parameter F2. The Oim and αi are Racah operators and reduced matrix elements, respectively...

  10. Inelastic critical scattering of neutrons from terbium

    DEFF Research Database (Denmark)

    Als-Nielsen, Jens Aage; Dietrich, O.W.; Marshall, W.

    1967-01-01

    We have measured the inelasticity of the critical neutron scattering in Tb above the Néel temperature. The results show that dynamical slowing down of fluctuations does occur at a second order phase transition.......We have measured the inelasticity of the critical neutron scattering in Tb above the Néel temperature. The results show that dynamical slowing down of fluctuations does occur at a second order phase transition....

  11. NICKEL ALUMINIDE SYNTHESIS REINFORCED WITH MOLYBDENUM BORIDE COMPOSITE

    Directory of Open Access Journals (Sweden)

    Mr. Khosen ф Ri

    2016-06-01

    Full Text Available The authors study obtaining a composite material NiAl - Mo2B5 while carrying out thermally coupled reactions of self-propagating high-temperature synthesis with a deoxidizing aluminothermal stage. The authors established ultimate and phase composition of the obtained composite. The microstructure is studied. It is shown that the composite consists of the intermetallic phase NiAl with Mo2B5 inclusions.

  12. NICKEL ALUMINIDE SYNTHESIS REINFORCED WITH MOLYBDENUM BORIDE COMPOSITE

    OpenAIRE

    Mr. Khosen ф Ri; Mr. Victor V. Gostishchev; Ms. Anastasia V. Medneva; Mr. Sergei N. Khimukhin; Mr. Ivan A. Astapov

    2016-01-01

    The authors study obtaining a composite material NiAl - Mo2B5 while carrying out thermally coupled reactions of self-propagating high-temperature synthesis with a deoxidizing aluminothermal stage. The authors established ultimate and phase composition of the obtained composite. The microstructure is studied. It is shown that the composite consists of the intermetallic phase NiAl with Mo2B5 inclusions.

  13. Fundamental Thermal and Mechanical Properties of Boride Ceramics

    Science.gov (United States)

    2014-02-28

    1600°C and a two-color pyrometer above 1500°C. Heating rates as high as 500°C/min have been achieved. To date, four point bend tests as described by...a two-color optical pyrometer and a programmable PID controller. Water cooled graphite pushrods and a fully articulated graphite 4-point bend...Mechanical Stress Evaluation by Neutrons and Synchrotron Radiation , November 10-12, 2009, Mito, Japan. 20. J. Watts, G.E. Hilmas, and W.G. Fahrenholtz

  14. Development of Boride Composite Materials for Cold Cathode Devices

    Science.gov (United States)

    1981-05-01

    pop. 775, 1979. Johnson, R., "The Lanthanum-Bormn System," J of Phys. Chem, Vol 65, 1961, p. 909. Kanitkar , P., "Field Emissicn Studies of the...Ianthanum HexaborideA’unqsten Sys ," J. Physics D: App!. Phys. Vol 9, 1976 pp L165-LI68. Kanitkar , P. L. "Field Emissicn Studi es of the Lanthanum

  15. Inelastic scattering of neutrons by spin waves in terbium

    DEFF Research Database (Denmark)

    Bjerrum Møller, Hans; Houmann, Jens Christian Gylden

    1966-01-01

    Measurements of spin-wave dispersion relations for magnons propagating in symmetry directions in ferromagnetic Tb; it is first experiment to give detailed information on magnetic excitations in heavy rare earths; Tb was chosen for these measurements because it is one of few rare-earth metals whic...... does not have very high thermal-neutron capture cross section, so that inelastic neutron scattering experiments can give satisfactory information on magnon dispersion relations....

  16. Coherent magnetic structures in terbium/holmium superlattices

    DEFF Research Database (Denmark)

    Bryn-Jacobsen, C.; Cowley, R.A.; McMorrow, D.F.

    1997-01-01

    Neutron-scattering techniques have been used to investigate the magnetic properties of three Tb/Ho superlattices grown by molecular-beam epitaxy. It is revealed that for temperatures in the range T = 10 to T-N(Ho)approximate to 130 K, there is a basal-plane ferromagnetic alignment of Tb moments w...

  17. Microstructure and properties of gravity sintered 316l stainless steel powder with nickel boride addition

    Directory of Open Access Journals (Sweden)

    Božić Dušan

    2016-01-01

    Full Text Available The present work demonstrates a procedure for synthesis of stainless steel powder by gravity sintering method. As an additive to the basic powder, NiB powder was added in the amount of 0.2 - 1.0 wt.%. Gravity sintering was done in vacuum, at the temperatures of 1100°C-1250°C, in the course of 3 - 60 min, using ceramic mould. Structural characterization was conducted by XRD, and microstructural analysis by optical and scanning electron microscope (SEM. Mechanical properties were investigated by tensile tests with steel rings. Density and permeability were determined by standard techniques for porous samples. Gravity sintered stainless steel with NiB addition had more superior mechanical and physico-chemical properties compared to stainless steel obtained by standard powder metallurgy procedures - pressing and sintering. [Projekat Ministarstva nauke Republike Srbije, br. 172005

  18. Manganese mono-boride, an inexpensive room temperature ferromagnetic hard material

    Science.gov (United States)

    Ma, Shuailing; Bao, Kuo; Tao, Qiang; Zhu, Pinwen; Ma, Teng; Liu, Bo; Liu, Yazhou; Cui, Tian

    2017-03-01

    We synthesized orthorhombic FeB-type MnB (space group: Pnma) with high pressure and high temperature method. MnB is a promising soft magnetic material, which is ferromagnetic with Curie temperature as high as 546.3 K, and high magnetization value up to 155.5 emu/g, and comparatively low coercive field. The strong room temperature ferromagnetic properties stem from the positive exchange-correlation between manganese atoms and the large number of unpaired Mn 3d electrons. The asymptotic Vickers hardness (AVH) is 15.7 GPa which is far higher than that of traditional ferromagnetic materials. The high hardness is ascribed to the zigzag boron chains running through manganese lattice, as unraveled by X-ray photoelectron spectroscopy result and first principle calculations. This exploration opens a new class of materials with the integration of superior mechanical properties, lower cost, electrical conductivity, and fantastic soft magnetic properties which will be significant for scientific research and industrial application as advanced structural and functional materials.

  19. Manganese mono-boride, an inexpensive room temperature ferromagnetic hard material

    OpenAIRE

    Shuailing Ma; Kuo Bao; Qiang Tao; Pinwen Zhu; Teng Ma; Bo Liu; Yazhou Liu; Tian Cui

    2017-01-01

    We synthesized orthorhombic FeB-type MnB (space group: Pnma) with high pressure and high temperature method. MnB is a promising soft magnetic material, which is ferromagnetic with Curie temperature as high as 546.3?K, and high magnetization value up to 155.5?emu/g, and comparatively low coercive field. The strong room temperature ferromagnetic properties stem from the positive exchange-correlation between manganese atoms and the large number of unpaired Mn 3d electrons. The asymptotic Vickers...

  20. Manganese mono-boride, an inexpensive room temperature ferromagnetic hard material.

    Science.gov (United States)

    Ma, Shuailing; Bao, Kuo; Tao, Qiang; Zhu, Pinwen; Ma, Teng; Liu, Bo; Liu, Yazhou; Cui, Tian

    2017-03-06

    We synthesized orthorhombic FeB-type MnB (space group: Pnma) with high pressure and high temperature method. MnB is a promising soft magnetic material, which is ferromagnetic with Curie temperature as high as 546.3 K, and high magnetization value up to 155.5 emu/g, and comparatively low coercive field. The strong room temperature ferromagnetic properties stem from the positive exchange-correlation between manganese atoms and the large number of unpaired Mn 3d electrons. The asymptotic Vickers hardness (AVH) is 15.7 GPa which is far higher than that of traditional ferromagnetic materials. The high hardness is ascribed to the zigzag boron chains running through manganese lattice, as unraveled by X-ray photoelectron spectroscopy result and first principle calculations. This exploration opens a new class of materials with the integration of superior mechanical properties, lower cost, electrical conductivity, and fantastic soft magnetic properties which will be significant for scientific research and industrial application as advanced structural and functional materials.

  1. Oxidation behavior of multiphase molybdenum-molybdenum silicide-molybdenum silicide boride intermetallics

    Science.gov (United States)

    Dheeradhada, Voramon Supatarawanich

    Multiphase Mo-Mo3Si-Mo5SiB2(T2) alloys of various compositions and microstructures were investigated for oxidation resistance at 800 and 1300°C. The alloys varied in Si/B ratio from 1:1 to 1:2 and their microstructures were processed to have the Mo phase distributed as a continuous phase or as discrete particles. At 800°C, the alloys exhibited poor oxidation resistance regardless of Si/B ratio or their microstructures. Oxide scale consisted of MoO 3 and boron-containing glass. Alloys with lower Si/B ratio yielded silicate glass with lower viscosity that resulted in lower weight loss compared to the high Si/B ratio alloys. Intermediate layers of Mo and Mo-Si-O were observed adjacent to Mo5SiB2 and Mo3Si phases, respectively. At 1300°C, the multiphase alloys developed a protective glass scale with an intermediate layer of (Mo+glass) between the base alloy and outer glass scale. Boron-lean silicate glass was essential for the protection from further oxidation. For oxidation resistance at 1300°C, alloys require a high Si/B ratio. In terms of microstructures, the multiphase alloys consisting of small Mo particles uniformly dispersed in fine spacing of silicide phases provide better oxidation resistance than the alloys with continuous Mo dendrites. Glass preferentially formed at Mo3Si rather than at T2 phase. Vapor-solid diffusion experiments were carried out with single phase alloys containing either Mo3Si or T2 as the major phase, and the multiphase Mo-10Si-10B(at%) alloy. The alloys were exposed to vacuum to induce silicon loss resulting in the formation of a Mo layer. In addition, microprobe analysis was carried out for the determination of composition profiles across the (Mo+glass) layer and the external glass scale formed on the Mo-13.2Si-13.2B (at%) alloy oxidized at 1300°C. The microprobe data were analyzed for interdiffusion fluxes and interdiffusion coefficients with the aid of a computer program called "MultiDiFlux (c)". The effective interdiffusion coefficients for Mo, Si, B, and O in various phases were also determined. The motion of the (metal/Mo+glass) and (Mo+glass/glass) interfaces was examined. An average effective interdiffusion coefficient of silicon in molybdenum at 1300°C was estimated as 10 -17 m2/s. Moreover, interdiffusion coefficients for each component in the Mo+glass layer were evaluated on the basis of Mishin's analysis.

  2. Formation of molybdenum boride cermet coating by the detonation spray process

    Science.gov (United States)

    Yang, Gao; Zu-Kun, Hei; Xiaolei, Xu; Gang, Xin

    2001-09-01

    The effects of the powder particle size and the acetylene/oxygen gas flow ratio during the detonation spray process on the amount of molybdenum phase, porosity, and hardness of the coatings using MoB powder were investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), etc. The results show that the presence of metallic molybdenum in the coating results from decomposition of MoB powder during thermal spray. The compositions of the coatings are metallic Mo, MoB, and Mo2B, which are different from the phases of the original powder. The amount of molybdenum phase increases monotonously with the oxygen/acetylene ratio, but the increasing rate for the fine powder is faster than that for the coarse powder. The porosity and hardness of the coating are related to the amount of molybdenum phase. The phase constitution of the coating is discussed.

  3. The Physics and Chemistry of carbides, Nitrides and Borides. Volume 185

    Science.gov (United States)

    1990-01-01

    orbits around the axial field lines. Near the substrate, the ECR resonance conditions allow the electrons to receive resonance impulses during each... orbit so these electrons acquire a higher energy than electrons 141 elsewhere in the cavity. Thus, the plasma forms preferentially in the region of these...34frittage et caracterisation de cdramiques dans le syst me zirconium- carbone-oxyg~ne", E.N.S. Mines de Saint-Etienne, (1986), Thtse (n* 54 C.I.). [102

  4. Boride ceramics covalent functionalization and its effect on the thermal conductivity of epoxy composites

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Zhi-Qiang, E-mail: yuzhiqiang@fudan.edu.cn [Department of Materials Science, Fudan University, 200433 Shanghai (China); Wu, Yicheng [Department of Materials Science, Fudan University, 200433 Shanghai (China); Wei, Bin; Baier, Horst [Institute of Lightweight Structures, Technical University Munich (TUM), Boltzmannstr. 15, D-85747 Garching (Germany)

    2015-08-15

    Zirconium diboride/aluminium oxide (ZrB{sub 2}/Al{sub 2}O{sub 3}) composite particles were functionalized with epoxide functionalized γ-glycidoxypropyltrimethoxysilane by the covalent bonding approach to improve the interfacial compatibility of composite particles in epoxy matrix. The composites of epoxy resin filled with functionalized ZrB{sub 2}/Al{sub 2}O{sub 3} were prepared by in situ bulk condensation polymerization of bisphenol A and epichlorohydrin in the presence of ZrB{sub 2}/Al{sub 2}O{sub 3}. The heat-conducting properties of composites were investigated by the finite element method (FEM) and the thermal conductivity test. The finite-element program ANSYS was used for this numerical analysis, and three-dimensional spheres-in-cube lattice array models were built to simulate the microstructure of composite materials for different filler contents. The thermal conductivity of composites was determined by laser flash method (LFA447 Nanoflash), using the measured heat capacity and thermal diffusivity, with separately entered density data. The results show that the effective chemical bonds are formed between ZrB{sub 2}/Al{sub 2}O{sub 3} and γ-glycidoxypropyltrimethoxysilane after the surface functionalization. The interfacial compatibility and bonding of modified particles with the epoxy matrix are improved. The thermal conductivities of functionalized composites with 3 vol% and 5 vol% loading are increased by 8.3% and 12.5% relative to the unmodified composites, respectively. Comparison of experimental values and calculated values of the thermal conductivity, the average relative differences are under 5%. The predictive values of thermal conductivity of epoxy composites are in reasonable agreement with the experimental values. - Highlights: • The surfaces of ZrB{sub 2}/Al{sub 2}O{sub 3} were functionalized by silane coupling agents. • The thermal conductivity (TC) of modified epoxy composites is improved significantly. • The FEM values of TC are in reasonable agreement with the experimental values.

  5. Improving Hardness and Toughness of Boride Composites Based on AIMgB14

    Energy Technology Data Exchange (ETDEWEB)

    Peters, Justin Steven [Iowa State Univ., Ames, IA (United States)

    2007-01-01

    The search for new super-hard materials has usually focused on strongly bonded, highly symmetric crystal structures similar to diamond. The two hardest single-phase materials, diamond and cubic boron nitride (cBN), are metastable, and both must be produced at high temperatures and pressures, which makes their production costly. In 2000, a superhard composite based on a low-symmetry, boron-rich compound was reported. Since then, many advances have been made in the study of this AlMgB14-TiB2 composite. The composite has been shown to exhibit hardness greater than either of its constituent phases, relying on its sub-micron microstructure to provide hardening and strengthening mechanisms. With possible hardness around 40 GPa, an AlMgB14 - 60 vol% TiB2 approaches the hardness of cBN, yet is amenable to processing under ambient pressure conditions. There are interesting aspects of both the AlMgB14 and TiB2 phases. AlMgB14 is comprised of a framework of boron, mostly in icosahedral arrangements. It is part of a family of 12 known compounds with the same boron lattice, with the metal atoms replaced by Li, Na, Y or a number of Lanthanides. Another peculiar trait of this family of compounds is that every one contains a certain amount of intrinsic vacancies on one or both of the metal sites. These vacancies are significant, ranging from 3 to 43% of sites depending on the composition. TiB2 is a popular specialty ceramic material due to its high hardness, moderate toughness, good corrosion resistance, and high thermal and electrical conductivity. The major drawback is the difficulty of densification of pure TiB2 ceramics. A combination of sintering aids, pressure, and temperatures of 1800 C are often required to achieve near full density articles. The AlMgB14 - TiB2 composites can achieve 99% density from hot-pressing at 1400 C. This is mostly due to the preparation of powders by a high-energy milling technique known as mechanical alloying. The resulting fine powders have high activity, and Fe from wear debris acts as a sintering aid. Mechanical alloying improves the sinterability of the composite material, it has the same effect on pure TiB2. TiB2 processed by high-energy milling has been found to achieve 99% theoretical density at 1400 C with the addition of ~1 wt% Fe. Both the AlMgB14 - TiB2 composites and pure TiB2 produced from these methods have enhanced mechanical properties due to their fine microstructures. These materials show exceptional promise in the field of wear resistance. This includes cutting tools, erosion resistant coatings, and low-friction sliding contacts to name a few. Under certain wear conditions, the composite material can show performance on par with that of current high-end cBN and WC materials tailored for wear resistance. The composite material also exhibits low reactivity with Ti alloys, a pre-requisite for effective machining of these alloys, a trait that few hard materials possess.

  6. Ground State Structures of Boron-Rich Rhodium Boride: An Ab Initio Study

    Science.gov (United States)

    Chu, Bin-Hua; Zhao, Yuan; Yan, Jin-Liang; Li, Da

    2018-01-01

    Not Available Supported by the Natural Science Foundation of Shandong Province under Grant Nos ZR2016AP02, ZR2016FM38 and ZR2016EMP01, the Innovation Project of Ludong University under Grant No LB2016013, the Open Project of State Key Laboratory of Superhard Materials of Jilin University under Grant No 201605, and the National Natural Science Foundation of China under Grant Nos 11704170 and 61705097.

  7. Photoluminescence studies of a Terbium(III) complex as a fluorescent probe for DNA detection

    Energy Technology Data Exchange (ETDEWEB)

    Khorasani-Motlagh, Mozhgan, E-mail: mkhorasani@chem.usb.ac.ir; Noroozifar, Meissam; Niroomand, Sona; Moodi, Asieh

    2013-11-15

    The photoluminescence properties of a Tb(III) complex of the form [Tb(phen){sub 2}Cl{sub 3}·OH{sub 2}] (phen=1,10-phenanthroline) in different solvents are presented. It shows the characteristic luminescence of the corresponding Ln{sup 3+} ion in the visible region. The emission intensity of this complex in coordinating solvent is higher than non-coordinating one. The suggested mechanism for the energy transfer between the ligand and Tb{sup 3+} ion is the intramolecular energy transfer mechanism. The interactions of the Tb(III) complex with fish salmon DNA are studied by fluorescence spectroscopy, circular dichroism study and viscosity measurements. The results of fluorescence titration reveal that DNA strongly quenches the intrinsic fluorescence of the complex through a static quenching procedure. The binding constant (K{sub b}) of the above metal complex at 25 °C is determined by the fluorescence titration method and it is found to be (8.06±0.01)×10{sup 3} M{sup −1}. The thermodynamic parameters (ΔH{sup 0}>0, ΔS{sup 0}>0 and ΔG{sup 0}<0) indicate that the hydrophobic interactions play a major role in DNA–Tb complex association. The results support the claim that the title complex bonds to FS-DNA by a groove mode. -- Highlights: • Photoluminescence of [Tb(phen){sub 2}Cl{sub 3}·OH{sub 2}] in different solvents are studied. • Tb(III) complex shows good binding affinity to FS DNA with K{sub b}=(8.06±0.01)×10{sup 3} M{sup −1}. • Viscosity of DNA almost unchanged by increasing amount of Tb complex. • CD spectrum of DNA has a little change with increasing amount of Tb complex. • Thermodynamic parameters indicate that the binding reaction is entropically driven.

  8. Lanthanides in Nuclear Medicine. The Production of Terbium-149 by Heavy Ion Beams

    CERN Document Server

    Dmitriev, S N; Zaitseva, N G; Maslov, O D; Molokanova, L G; Starodub, G Ya; Shishkin, S V; Shishkina, T V

    2001-01-01

    Among radioactive isotopes of lanthanide series elements, finding the increasing using in nuclear medicine, alpha-emitter {149}Tb (T_{1/2} = 4.118 h; EC 76.2 %; beta^+ 7.1 %; alpha 16.7 %) is considered as a perspective radionuclide for radioimmunotherapy. The aim of the present work is to study experimental conditions of the {149}Tb production in reactions Nd({12}C, xn){149}Dy (4.23 min; beta^+, EC)\\to {149}Tb when the Nd targets have been irradiated by heavy ions of carbon. On the basis of results of formation and decay of {149}Dy\\to{149}Tb evaluation of the {149}Tb activity, is made which can be received under optimum conditions (enriched {142}Nd target, {12}C ions with the energy 120 MeV and up to current 100 mu A, time of irradiating 8-10 hours). Under these conditions {149}Tb can be obtained up to 30 GBq (up to 0.8 Ci).

  9. Poly[[aqua-?3-picolinato-?2-picolinato-dipicolinatopotassium(I)terbium(III)] 2.5-hydrate

    OpenAIRE

    Filipe A. Almeida Paz; João Rocha; Jacek Klinowski; Tito Trindade; Nogueira,Helena I. S.; Soares-Santos, Paula C. R.; Cunha-Silva, Lu?s

    2008-01-01

    In the title compound, [KTb(C6H4NO2)4(H2O)]·2.5H2O, each Tb3+ centre is coordinated by four N and five O atoms from five distinct picolinate ligands in a geometry resembling a highly distorted tricapped trigonal prism. One of the ligands establishes a skew bridge between neighbouring Tb3+ centres, leading to the formation of one-dimensional anionic polymeric chains, {[(C6H4NO2)4Tb]−}n, running along the direction [010]. Each K+ cation is seven-coordinated by six O atoms from one an...

  10. Spin waves in terbium. III. Magnetic anisotropy at zero wave vector

    DEFF Research Database (Denmark)

    Houmann, Jens Christian Gylden; Jensen, J.; Touborg, P.

    1975-01-01

    The energy gap at zero wave vector in the spin-wave dispersion relation of ferromagnetic. Tb has been studied by inelastic neutron scattering. The energy was measured as a function of temperature and applied magnetic field, and the dynamic anisotropy parameters were deduced from the results....... The axial anisotropy is found to depend sensitively on the orientation of the magnetic moments in the basal plane. This behavior is shown to be a convincing indication of considerable two-ion contributions to the magnetic anisotropy at zero wave vector. With the exception of the sixfold basal...... the effects of zero-point deviations from the fully aligned ground state, and we tentatively propose polarization-dependent two-ion couplings as their origin....

  11. Structural and Magnetic Anisotropy in Amorphous Terbium-Iron Thin Films

    Science.gov (United States)

    Hufnagel, Todd Clayton

    1995-01-01

    High density, removable media magnetooptic disk drives have recently begun to make significant gains in the information mass storage market. The media in these disks are amorphous rare-earth/transition-metal (RE-TM) alloys. One vital property of these materials is a large perpendicular magnetic anisotropy; that is, an easy axis of magnetization which is perpendicular to the plane of the film. A variety of theories, sometimes contradictory, have been proposed to account for this surprising presence of an anisotropic property in an amorphous material. Recent research indicates that there is an underlying atomic-scale structural anisotropy which is responsible for the observed magnetic anisotropy. Several different types of structural anisotropy have been proposed to account for the observed magnetic anisotropy, including pair-ordering anisotropy (anisotropic chemical short-range order) and bond orientation anisotropy (an anisotropy in coordination number or distances independent of chemical ordering). We have studied the structural origins of perpendicular magnetic anisotropy in amorphous Tb-Fe thin films by employing high-energy and anomalous dispersion x-ray scattering. The as-deposited films show a clear structural anisotropy, with a preference for Tb-Fe near neighbors to align in the out-of-plane direction. These films also have a large perpendicular magnetic anisotropy. Upon annealing, the magnetic anisotropy energy drops significantly, and we see a corresponding reduction in the structural anisotropy. The radial distribution functions indicate that the number of Tb-Fe near-neighbors increases in the in-plane direction, but does not change in the out-of-plane direction. Therefore, the distribution of Tb-Fe near-neighbors becomes more uniform upon annealing. We propose that the observed reduction in perpendicular magnetic anisotropy energy is a result of this change in structure. Our results support the pair -ordering anisotropy model of the structural anisotropy in amorphous Tb-Fe thin films. We see no evidence to support the bond orientation anisotropy model.

  12. Luminescence properties of terbium-doped Li3PO4 phosphor for ...

    Indian Academy of Sciences (India)

    Antonov-Romanovskii et al [2] firstly suggested applications of OSL for personal dosime- try. This technique got momentum for personnel dosime- try after the development of α-Al2O3:C. OSL properties of α-Al2O3:C have been investigated for personnel dosimetry, environmental dosimetry, medical dosimetry and space.

  13. Luminescence properties of terbium-doped Li3PO4 phosphor for ...

    Indian Academy of Sciences (India)

    The powder X-ray diffraction (PXRD), photoluminescence (PL) emission and excitation spectra, thermoluminescence (TL) and optically stimulated luminescence (OSL) were measured. The particle size was calculated using the Debye Scherrer formula and found to be 79.42 nm. PL emission spectra of Li 3 PO 4 :Tb 3 + ...

  14. Charge-transfer-based terbium MOF nanoparticles as fluorescent pH sensor for extreme acidity.

    Science.gov (United States)

    Qi, Zewan; Chen, Yang

    2017-01-15

    Newly emerged metal organic frameworks (MOFs) have aroused the great interest in designing functional materials by means of its flexible structure and component. In this study, we used lanthanide Tb 3+ ions and small molecular ligands to design and assemble a kind of pH-sensitive MOF nanoparticle based on intramolecular-charge-transfer effect. This kind of made-to-order MOF nanoparticle for H + is highly specific and sensitive and could be used to fluorescently indicate pH value of strong acidic solution via preset mechanism through luminescence of Tb 3+ . The long luminescence lifetime of Tb 3+ allows eliminating concomitant non-specific fluorescence by time-revised fluorescence techniques, processing an advantage in sensing H + in biological media with strong autofluorescence. Our method showed a great potential of MOF structures in designing and constructing sensitive sensing materials for specific analytes directly via the assembly of functional ions/ligands. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. Assessment of terbium (III) as a luminescent probe for the detection of tuberculosis biomarkers

    Energy Technology Data Exchange (ETDEWEB)

    Bamogo, W. [CNRS, IRAMIS, UMR 3685 NIMBE/LEDNA, F-91191 Gif-sur-Yvette (France); Mugherli, L. [CEA, IRAMIS, UMR 3685 NIMBE/LEDNA, F-91191 Gif-sur-Yvette (France); Banyasz, A. [CNRS, IRAMIS, LIDyL/Laboratoire Francis Perrin, URA 2453, F-91191 Gif-sur-Yvette (France); Novelli-Rousseau, A.; Mallard, F. [BioMérieux SA, F-38000 Grenoble (France); Tran-Thi, T.-H., E-mail: thu-hoa.tran-thi@cea.fr [CNRS, IRAMIS, UMR 3685 NIMBE/LEDNA, F-91191 Gif-sur-Yvette (France)

    2015-10-08

    A detection method for nicotinic acid, a specific metabolite marker of Mycobacterium tuberculosis present in cultures and patients' breath, is studied in complex solutions containing other metabolites and in biological media such as urine, saliva and breath condensate. The method is based on the analysis of the luminescence increase of Tb{sup 3+} complexes in the presence of nicotinic acid due to the energy transfer from the excited ligand to the lanthanide ion. It is shown that other potential markers found in M. tuberculosis culture supernatant, such as methyl phenylacetate, p-methyl anisate, methyl nicotinate and 2-methoxy biphenyl, can interfere with nicotinic acid via a competitive absorption of the excitation photons. A new strategy to circumvent these interferences is proposed with an upstream trapping of volatile markers preceding the detection of nicotinic acid in the liquid phase via the luminescence of Tb{sup 3+} complexes. The cost of the method is evaluated and compared with the Xpert MTB/RIF test endorsed by the World Health Organization. - Highlights: • Nicotinic acid, a specific marker of M. tuberculosis, can be detected via luminescence. • The detection limit with a commercial phosphorimeter is 0.4 µmol·L{sup -1}. • Other metabolites of M. tuberculosis can interfere via absorbed excitation light. • The interference can be removed via trapping of the most volatile metabolites. • A breath analysis procedure's cost is compared with the Xpert TBM/RIF test.

  16. A highly porous luminescent terbium-organic framework for reversible anion sensing

    Energy Technology Data Exchange (ETDEWEB)

    Wong, K.L.; Law, G.L.; Wong, W.T. [Department of Chemistry, The University of Hong Kong, Pokfulam Road, Hong Kong (China); Yang, Y.Y. [School of Chemistry and Chemical Engineering, Sun Yat-Sen University, Guangzhou 510275 (China)

    2006-04-18

    Unique tailored porous frameworks incorporating a lanthanide metal center have been designed to function as chemical detectors. A flexible multidentate ligand, mucic acid, is used to differentiate between several anions, thus creating an organic framework that is ideally suited for applications in gas separation, sensors, and chemical switches. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

  17. Synthesis and characterization of wide bandgap semiconductors doped with terbium for electroluminescent devices

    OpenAIRE

    Montañez Huamán, Liz Margarita

    2016-01-01

    En el presente trabajo de investigación se ha estudiado propiedades estequiometrias, estructurales y de emisión de luz de semiconductor de amplio ancho de banda dopados con terbio. La difracción de rayos-X en ángulo rasante confirma el estado amorfo de las películas. Los espectros de absorción infrarroja muestran la formación de óxidos en las películas y la espectroscopia de foto-electrones de rayos-X revela la formación de oxinitruro de aluminio y oxicarburo de silicio. Las pe...

  18. Synthesis and characterization of terbium-doped SrSnO3 pigments

    Czech Academy of Sciences Publication Activity Database

    Dohnalová, Ž.; Gorodylova, N.; Šulcová, P.; Vlček, Milan

    2014-01-01

    Roč. 40, č. 8 (2014), s. 12637-12645 ISSN 0272-8842 Institutional support: RVO:61389013 Keywords : pigments * solid state reaction * perovskites Subject RIV: CA - Inorganic Chemistry Impact factor: 2.605, year: 2014

  19. An optical material for the detection of β-hydroxybutyrate based on a terbium complex

    Science.gov (United States)

    Wang, Xiaomiao; Chen, Huili; Li, Hua

    2014-02-01

    A novel Tb3+ complex (Tb(C14H10O4)ṡCl, TbL2) based on benzoic acid (L+H) was successfully synthesized, and gave a weak green emission in methanol-water (V:V, 4:1, pH 4.49). With the addition of β-hydroxybutyrate (β-HB) to a semi-aqueous solution of TbL2, an increment of the luminescent intensity at 545 nm assigned to 5D4 → 7F5 transition of Tb3+ was measured, which was evident to the naked eye. The response showed high selectivity for β-HB compared with other common anions including Cl-, NO3-, CO32-, PO43-, HPO42-, HPO4-, CO42-, PO74-, SO42-, lactate, AcO-, citrate, malate therefore it has the potential to be applied as a luminescent sensor for β-HB.

  20. Research and Development on Titanium Alloys

    Science.gov (United States)

    1949-10-31

    are being prepared by the Norton Company for evaluation. Titanium boride , tantalum boride , zirconium boride , tungsten boride , and molybdenum boride ...alloying additionO will be ex- tended. 9 Ternary alloys of manganese and carbon, manganese and vanadium, and molybdenum and tungsten, prepared by...graphite crucibles lined with tantalum carbide and turgsten boride as refractories for molten titanium,. Melts were prepared In crucibles made of zirconium

  1. Electrical and magnetic properties of several ruthenates and superconductivity in magnesium boride and MgCNi(3)

    Science.gov (United States)

    He, Tao

    2002-09-01

    Perovskite-based ruthenates have been receiving considerable attention both because of their interesting and variable magnetic properties, and because of the discovery of exotic superconductivity in the layered ruthenate Sr 2RuO4. Another perovskite, SrRuO3, is the only known oxide ferromagnet with a 4d transition metal, and magnetism is easily suppressed by Ca doping. The suppression of ferromagnetic interactions in SrxCa1-xRuO3 has frequently been attributed to the orthorhombic structural distortion, either through the crossover to classical antiferromagnetic interactions, or, alternatively, to a nearly ferromagnetic metal. This study reports the comparison of the magnetic properties of Srx(Na0.5La0.5)1-xRuO 3 to SrxCa1-xRuO3, showing that there is a much faster suppression of ferromagnetic interactions in the former case. Neither orthorhombic distortion nor cation size disorder can explain the observed difference. Instead, the difference may be attributed to charge disorder on the A-site, which greatly affects the local environment of Ru atoms and leads to the faster suppression of the long-range ferromagnetic state. The magnetic ground state of perovskite structure CaRuO3 has been enigmatic for decades. This study also shows that paramagnetic CaRuO 3 can be made ferromagnetic by very small amounts of partial substitution of Ru by various transition metals. The results are consistent with the recent proposal that CaRuO3 is not a classical antiferromagnet, but rather is poised at a critical point between ferromagnetic and paramagnetic ground states. Ti, Fe, Mn and Ni doping result in ferromagnetic behavior. The second part of this thesis is on the superconductivity of MgB 2 and MgCNi3. Since the discovery of superconductivity in MgB2 in January 2001, detailed information on its properties has been rapidly accumulated. The reported properties, the very simple structure, and the commercial availability of this material make MgB2 a favorite candidate for large scale and electronic applications. In thin film fabrication, the reactivity of MgB2 with substrate materials or insulating or metallic layers in multi-layer circuits is an important factor. In this work the reactivity of MgB2 with powdered forms of common substrate and electronic materials is studied. Some oxides and nitrides prove to be potentially good substrates for making thin films, while others, including some commonly used substrates like Al2O3, SrTiO 3, and SiO2, have serious chemical compatibility problems. In the latter case, caution should be taken when fabricating thin films. This thesis also describes the discovery of superconductivity at 8 K in the perovskite structure compound MgCNi3. This material is the three-dimensional analogue of the LnNi2B2C family of superconductors, which have Tcs up to 16K. The itinerant electrons in both LnNi2B2C and MgCNi3 are based on partial filling of Ni d-states, which generally leads to ferromagnetism, as is the case in metallic Ni. The very high relative proportion of Ni in MgCNi3 is especially suggestive of the possible importance of magnetic interactions in the superconductivity, and, further, the lower Tc of the three-dimensional compound is contrary to conventional ideas.

  2. Catalytic Reductions and Tandem Reactions of Nitro Compounds Using in Situ Prepared Nickel Boride Catalyst in Nanocellulose Solution.

    Science.gov (United States)

    Prathap, Kaniraj Jeya; Wu, Qiong; Olsson, Richard T; Dinér, Peter

    2017-09-15

    A mild and efficient method for the in situ reduction of a wide range of nitroarenes and aliphatic nitrocompounds to amines in excellent yields using nickel chloride/sodium borohydride in a solution of TEMPO-oxidized nanocellulose in water (0.01 wt %) is described. The nanocellulose has a stabilizing effect on the catalyst, which increases the turnover number and enables low loading of nickel catalyst (0.1-0.25 mol % NiCl2). In addition, two tandem protocols were developed in which the in situ formed amines were either Boc-protected to carbamates or further reacted with an epoxide to yield β-amino alcohols in excellent yields.

  3. Multiple Electron Charge Transfer Chemistries for Electrochemical Energy Storage Systems: The Metal Boride and Metal Air Battery

    Science.gov (United States)

    Stuart, Jessica F.

    The primary focus of this work has been to develop high-energy capacity batteries capable of undergoing multiple electron charge transfer redox reactions to address the growing demand for improved electrical energy storage systems that can be applied to a range of applications. As the levels of carbon dioxide (CO2) increase in the Earth's atmosphere, the effects on climate change become increasingly apparent. According to the Energy Information Administration (EIA), the U.S. electric power sector is responsible for the release of 2,039 million metric tons of CO2 annually, equating to 39% of total U.S. energy-related CO2 emissions. Both nationally and abroad, there are numerous issues associated with the generation and use of electricity aside from the overwhelming dependence on fossil fuels and the subsequent carbon emissions, including reliability of the grid and the utilization of renewable energies. Renewable energy makes up a relatively small portion of total energy contributions worldwide, accounting for only 13% of the 3,955 billion kilowatt-hours of electricity produced each year, as reported by the EIA. As the demand to reduce our dependence on fossils fuels and transition to renewable energy sources increases, cost effective large-scale electrical energy storage must be established for renewable energy to become a sustainable option for the future. A high capacity energy storage system capable of leveling the intermittent nature of energy sources such as solar, wind, and water into the electric grid and provide electricity at times of high demand will facilitate this transition. In 2008, the Licht Group presented the highest volumetric energy capacity battery, the vanadium diboride (VB2) air battery, exceedingly proficient in transferring eleven electrons per molecule. This body of work focuses on new developments to this early battery such as fundamentally understanding the net discharge mechanism of the system, evaluation of the properties and performance of nanoscopic anodic materials in addition to the previously developed macroscopic system, as well as the exploration of a high-energy capacity TiB 2/VB2 composite anode. However, the greatest challenge to this room temperature VB2 primary battery is to develop a means to electrochemically recharge the anodic material (how to reinsert the eleven electrons per molecule that are removed during the battery's discharge). Rechargeable batteries, such as the new molten air battery presented in this thesis, offer a high intrinsic capacity mode for energy storage and overcome problems such as the need for higher energy capacity, cost-effective batteries for a range of electronic, transportation, and large-scale power storage devices. Molten air batteries presented and discussed in this work are viable systems that provide a means to electrochemically recharge the VB2-air battery and deliver large-scale energy storage due to their scalability, location flexibility, construction from readily available resources, and offer increased energy storage capacity for the electric grid. One example is the VB2 molten air battery, which discharges according to: VB 2 + 11/4 O2 → 1/ 2 V2O5 + B2O3 (1). Previously, our group has shown that carbon dioxide can be captured from atmospheric air concentrations at solar efficiencies as high as 50%, and that carbon dioxide emissions associated with the production of several commodities can be electrochemically avoided in by the Solar Thermal Electrochemical Process (STEP). Utilizing this process, the carbon molten air battery relies on carbon dioxide directly from the air: Charging: CO2 (g) → C (solid) + O2 (g) (2) Discharging: C (solid) + O2 (g) → CO2 (g) (3). More specifically, in a molten carbonate electrolyte containing added oxide, such as lithium carbonate with lithium oxide, the four-electron charging reaction, Equation 2, approaches 100% faradic efficiency and can be described as the following two equations: O2- (dissolved) + CO2 (g) → CO 32- (molten) (2a) CO32- (molten) ?→ C (solid) + O2 (g) + O2- (dissolved) (2b). Thus, powered by the oxidation of carbon formed directly from the CO 2 in our earth's atmosphere, the carbon molten air battery is a viable system to provide large-scale energy storage. These batteries are rechargeable and have amongst the highest intrinsic battery storage capacities available. The electron charge transfer chemistry is demonstrated through three examples. These examples utilize iron, carbon, and vanadium diboride as reactive materials, each containing intrinsic volumetric energy capacities of 10,000 Wh/L for Fe to Fe (III), 19,000 Wh/L for C to CO2, and 27,000 Wh/L for VB2 to B2O3 and V2O 5, compared to 6,200 Wh/L for the lithium air battery.

  4. pH dependent photophysical studies of new europium and terbium complexes of tripodal ligand: Experimental and semiempirical approach

    Energy Technology Data Exchange (ETDEWEB)

    Akbar, Rifat [Department of Chemistry, Sant Longowal Institute of Engineering & Technology, Longowal, Punjab 148106 (India); Baral, Minati [Department of Chemistry, National Institute of Technology Kurukshetra, Haryana 136119 (India); Kanungo, B K, E-mail: b.kanungo@gmail.com [Department of Chemistry, Sant Longowal Institute of Engineering & Technology, Longowal, Punjab 148106 (India)

    2015-11-15

    The photophysical properties of adduct of a novel nonadentate tripodal ligand, 5,5′-(2-(((8-hydroxyquinolin-5-yl)methylamino)methyl)-2-methylpropane-1, 3-diyl)bis(azanediyl)bis(methylene diquinolin-8-ol, (TAME5OX), with Eu{sup 3+} and Tb{sup 3+} metal ions have been probed for photonics applications. The absorption spectroscopy of these complexes show remarkable spectral changes due to characteristic lanthanide transitions, which support the use of TAME5OX as a sensitive optical pH based sensor to detect Ln{sup 3+} metal ions in biological systems. In addition, these complexes have also been shown to exhibit strong green fluorescence allowing simultaneous sensing within the visible region under physiological pH in competitive medium for both Eu{sup 3+} and Tb{sup 3+} ions. The intense fluorescence from these compounds were revealed to intermittently get quenched under acidic as well as basic conditions due to the photoinduced intramolecular electron transfer from excited 8-hydroxyquinoline (8-HQ) moiety to metal ion, just an opposite process. This renders these compounds the OFF–ON–OFF type of pH-dependent fluorescent sensor. The thermodynamic stability and aqueous coordination chemistry of the chelator with the said lanthanide ions have also been probed by potentiometric, UV–visible and fluorescence spectrophotometric method. TAME5OX has been found to form two protonated complexes [Ln(H{sub 5}L)]{sup 5+} and [Ln(H{sub 4}L)]{sup 4+} below pH 2.5 with both metal ions, which consecutively deprotonates through one proton process with rise of pH. The formation constants (log β{sub 11n}) of neutral complexes have been determined to be 33.51 and 32.16 with pLn (pLn=−log[Ln{sup 3+}]) values of 16.14 and 19.48 for Eu{sup 3+} and Tb{sup 3+} ions, respectively, calculated at pH 7.4, indicating TAME5OX is a good lanthanide synthetic chelator. The emission lifetimes of the Eu{sup 3+} and Tb{sup 3+} complexes recorded in D{sub 2}O and H{sub 2}O suggest the presence of water molecules in the first coordination sphere of the metal ions. NMR titrations were carried out to determine the stoichiometry of chelates. The complexe's coordination geometries were optimized by using PM7 as sparkle/PM7 model. The theoretical electronic behavior was evaluated to support the experimental findings, based on ZINDO/S methodology at configuration interaction with single excitations (CIS) level. These results emphasize the capability of the use of the theoretical models in prediction of geometries and all other calculations of compounds containing lanthanide ions and create new interesting possibilities for the design in-silico of novel and highly efficient lanthanide–organic edifice. - Highlights: • Photophysical behavior of Eu{sup 3+} and Tb{sup 3+} complexes of TAME5OX has been investigated. • This tripodal ligand forms thermodynamically stable Ln{sup 3+} complexes. • These compounds exhibit strong green fluorescence under physiological pH. • Green fluorescence gets quenched under acidic and basic conditions, due to PET process. • This renders these compounds the OFF–ON–OFF type of pH-dependent fluorescent sensors.

  5. Visible photoluminescence in polycrystalline terbium doped aluminum nitride (Tb:AlN) ceramics with high thermal conductivity

    Science.gov (United States)

    Wieg, A. T.; Kodera, Y.; Wang, Z.; Imai, T.; Dames, C.; Garay, J. E.

    2012-09-01

    Thermal management continues to be one of the major challenges in the development of high powered light sources such as solid state lasers. In particular, the relatively low thermal conductivity of standard photoluminescent (PL) materials limits the overall power output and/or duty cycle. We present a method based on current activated pressure assisted densification for the fabrication of high thermal conductivity PL materials: rare earth doped polycrystalline bulk aluminum nitride. Specifically, the ceramics are translucent and are doped with Tb3+, allowing for emission in the visible. Remarkably, the ceramics have a room temperature thermal conductivity of 94 W/(m K) which is almost seven times higher than that of the state of the art host material, Nd-doped yttrium aluminum garnet. These light emitting properties coupled with very high thermal conductivity should enable the development of a wide variety of more powerful light sources.

  6. Preparation of extractive resins for producing terbium-161; Preparacion de resinas extractivas para produccion de terbio-161

    Energy Technology Data Exchange (ETDEWEB)

    De la Cruz B, C. C.; Monroy G, F. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)], e-mail: fabiola.monroy@inin.gob.mx

    2009-10-15

    This paper presents the development of a methodology for extractive resins preparation to base of HDEHP, which allows to separation of Tb from Gd generating an own technology of preparation of these resins. The study included the extractive resins preparation from 6 different supports: kieselguhr Dg, alumina, red volcanic rock, chiluca, quarry and fluorite; two treatment types of of supports and varied concentrations of HDEHP extractant (di(2-etil hexyl) orthophosphoric acid), in order to determine which resin has improved efficiency of Gd and Tb separation, and radionuclide purity of {sup 161}Tb. Resins were prepared to base of kieselguhr to determine the most appropriate silicon deposition process. Two silicon deposition treatments were realized: treatment I , by contact with silicon deposition solution (dimethyldichlorosilane / heptane 1:30) and treatment II by contact with vapors of dimethyldichlorosilane in vacuum. The extractant retention was carried out to different concentrations of HDEHP / acetone: 1:4, 1:8, 1:15, 1:20, 1:30 and 1:40. According to the results, there is not direct relation of HDEHP concentration used in extractive resins preparation to base of kieselguhr over the efficiency of Gd and Tb separation and of radionuclide purity of {sup 161}Tb. The effect of support in the efficiency of Gd and Tb separation was studied to prepare resins with the supports kieselguhr, alumina, quarry, chiluca, volcanic rock and fluorite, using the silicon deposition treatment II for the supports and a concentration of HDEHP / acetone 1:20, for extractant retention. Only resins based on kieselguhr could separate to Gd from Tb quantitatively, the resin at a concentration of HDEHP / Acetone 1:20 was the best results obtained in Gd and Tb separation, achieving a separation efficiency greater than 90% and a radionuclide purity higher than 99%. (Author)

  7. Synthesis and Characterization of Europium(III) and Terbium(III) Complexes: An Advanced Undergraduate Inorganic Chemistry Experiment

    Science.gov (United States)

    Swavey, Shawn

    2010-01-01

    Undergraduate laboratories rarely involve lanthanide coordination chemistry. This is unfortunate in light of the ease with which many of these complexes are made and the interesting and instructive photophysical properties they entail. The forbidden nature of the 4f transitions associated with the lanthanides is overcome by incorporation of…

  8. Sensitized green emission of terbium with dibenzoylmethane and 1, 10 phenanthroline in polyvinyl alcohol and polyvinyl pyrrolidone blends

    Science.gov (United States)

    Kumar, Brijesh; Kaur, Gagandeep; Rai, S. B.

    2017-12-01

    Tb doped polyvinyl alcohol: polyvinyl pyrrolidone blends with dibenzoylmethane (DBM) and 1, 10 Phenanthroline (Phen) have been prepared by solution cast technique. Bond formation amongst the ligands and Tb3 + ions in the doped polymer has been confirmed employing Fourier Transform Infrared (FTIR) techniques. Optical properties of the Tb3 + ions have been investigated using UV-Vis absorption, excitation and fluorescence studies excited by different radiations. Addition of dimethylbenzoate and 1, 10 Phenanthroline to the polymer blend increases the luminescence from Tb3 + ions along with energy transfer from the polymer blend itself. Luminescence decay curve analysis affirms the non-radiative energy transfer from DBM and Phen to Tb3 + ions, which is identified as the reason behind this enhancement. The fluorescence decay time of PVA-PVP host decreases from 6.02 ns to 2.31 ns showing an evidence of energy transfer from the host blend to the complexed Tb ions. Similarly the lifetime of DBM and Phen and both in the blend reduces in the complexed system showing the feasibility of energy transfer from these excited DBM and Phen to Tb3 + and is proposed as the cause of the above observations. These entire phenomena have been explained by the energy level diagram.

  9. A Terbium Metal-Organic Framework for Highly Selective and Sensitive Luminescence Sensing of Hg2+Ions in Aqueous Solution.

    Science.gov (United States)

    Xia, Tifeng; Song, Tao; Zhang, Gege; Cui, Yuanjing; Yang, Yu; Wang, Zhiyu; Qian, Guodong

    2016-12-19

    A series of isomorphic lanthanide metal-organic frameworks (MOFs) Ln(TATAB)⋅(DMF) 4 (H 2 O)(MeOH) 0.5 (LnTATAB, Ln=Eu, Tb, Sm, Dy, Gd; H 3 TATAB=4,4',4''-s-triazine-1,3,5-triyltri-p-aminobenzoic acid) have been solvothermally synthesized and structurally characterized. Among these MOFs, TbTATAB exhibits good water stability and a high fluorescence quantum yield. Because mercury ions (Hg 2+ ) have a high affinity to nitrogen atoms, and the space between multiple nitrogen atoms from triazine and imino groups is suitable for interacting with Hg 2+ ions, TbTATAB shows highly selective and sensitive detection of Hg 2+ in aqueous solution with a detection limit of 4.4 nm. Furthermore, it was successfully applied to detect Hg 2+ ions in natural water samples. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Peculiarities of structure state and mechanical characteristics in ion-plasma condensates of quasibinary system borides W2B5-TiB2

    Directory of Open Access Journals (Sweden)

    Sobol O.V.

    2006-01-01

    Full Text Available In order to create high-durable, wear-resistant materials for a wide range of functional applications, comparative investigations of the structure and mechanical characteristics of ion-plasma Ti-W-B nano-crystalline condensates were carried out. The range of condensation rates 0.11÷0.25nm/s was found to be critical for the coatings obtained from the target with 80 vol% W2B5-20 vol% TiB2. Below this, a phase with a cubic lattice (W,TiB0.7…1.2(O,N,C0.3…0.2 formed, while over this range, a solid solution (W,TiB2 with a hexagonal lattice and element composition close to the sputtered target was observed. The structure state of the material changed from cluster-crystalline (under low sputter potentials U=0.6…1.0 kV to textured- crystalline (under U>2.2 kV. Structure perfection improvement with U increase results in higher hardness and elastic modulus of condensates. The conditions of cluster component formation and its effect on hardness and elastic modulus of condensates are discussed. .

  11. Thermionic emission and vaporization behavior of the ternary systems of lanthanum hexaboride containing molybdenum boride, molybdenum diboride, zirconium diboride, gadolinium hexaboride, and neodymium hexaboride

    Science.gov (United States)

    Storms, E. K.

    1983-02-01

    The addition of various compounds to LaB6 did not improve the thermionic emission over that of pure LaB6. This experience and general conclusions, which result by considering the vaporization properties of these and other materials, greatly limit the options available to improve the properties of LaB6 by forming a ternary system. The principles which must be considered, in order to simplify future work, are described.

  12. Effect of double addition of V and Cr on the properties of Mo{sub 2}NiB{sub 2} ternary boride-based cermets

    Energy Technology Data Exchange (ETDEWEB)

    Shiota, Yuusuke; Miyajima, Yuuta; Fujima, Takuya; Takagi, Ken-ichi [Department of Mechanical Engineering, Tokyo City University 1-28-1 Tamazutsumi, Setagaya-ku, Tokyo 158-8557 (Japan)], E-mail: ktakagi@tcu.ac.jp

    2009-06-01

    The effect of double addition of V and Cr on the mechanical properties and microstructure of Mo{sub 2}NiB{sub 2} base cermet was investigated. Total additional amount of V and Cr was fixed to 12.5 mass% and the fraction between the two additives was varied. Transverse rupture strength (TRS) and Rockwell A-scale hardness (HRA) were measured on the cermets and discussed together with their microstructure obtained by X-ray diffraction (XRD) and backscattered electron images (COMP). Addition of 2.5-mass% Cr and 10-mass% V showed the highest mechanical properties. Microstructural analysis revealed that brittle orthoronbic-M{sub 5}B{sub 3} phase was formed in high V fraction. The corrosion resistance of the cermets against hydrochloric acid was superior to that of JIS SUS 304. The resistance against nitric acid decreased with decreasing Cr content and was lower than that of SUS 304.

  13. Diffusional Growth Kinetics Analisys of Fe2B Layers Applied During the Coating Powder-Pack Boriding Process on an AISI 1026 Steel

    Directory of Open Access Journals (Sweden)

    M. Elias-Espinosa

    2015-01-01

    Full Text Available La exigencia de emplear materiales con propiedades avanzadas incluyen la necesidad de aplicar recubrimientos de alta resistencia que alarguen la vida de útil de aceros comerciales, de esta forma, el tratamiento termoquímico de borurización tiene el potencial para cumplir estos requerimientos. En este trabajo de investigación se formula un modelo matemático para analizar la cinética de crecimiento de las capas de 2 Fe B formadas sobre la superficie de un acero AISI 1026. El modelo matemático propuesto se desarrolló en base a la solución de la ecuación de balance de masa de la interface de crecimiento 2 Fe B/Fe para evaluar el coeficiente de difusión del boro a través de las capas de Fe2B en un rango de temperaturas de 1123 a1273 K. En el modelo desarrollado se incluyó el tiempo de incubación del boruro para formar la fase Fe2B. El modelo matemático fue validado con datos experimentales realizados a una temperatura de 1253 K y tiempo de siete horas. Las capas de boruro fueron caracterizadas y analizadas por microscopia óptica y de barrido (se obtuvo un EDS, así como por Difracción de Rayos – X (XRD. Se utilizó la técnica de indentación Daimler-Benz Rockwell-C para evaluar cualitativamente la adherencia de la capa de Fe2B sobre el sustrato (acero AISI 1026. Para usos prácticos y para un espesor determinado, se propuso un diagrama a espesor constante (215 μm el cual es controlado con la variación de la temperatura y tiempo de exposición al recubrimiento. De los resultados obtenidos, se encontró que la energía de activación para el boro en el acero AISI 1026 es igual a 178 kJ mol-1.

  14. Advanced Cathodes for Next Generation Electric Propulsion Technology

    Science.gov (United States)

    2008-03-01

    28 Boride Cathodes...45 Figure 15. Molybdenum Hollow Cathode Tube .............................................................. 46...CeB6 as a hollow cathode electron emitter. Additionally, all work in the US published on boride hollow cathodes are for high-current applications

  15. On the Nucleation and Growth of Alpha-Ti Off of TiB Precipitates (PREPRINT)

    Science.gov (United States)

    2010-01-01

    the aluminum and oxygen are enriched in α-Ti phase and depleted in the boride . In contrast, the molybdenum and niobium are enriched in the boride ...that a dispersion of thermally stable titanium- boride particles, formed by trace boron additions, was effective in restricting the grain growth...reinforced by the TiB phase [6-13]. The boride particles act as the pinning sites for the grain boundaries. In the TiB reinforced Ti-6Al-4V alloy

  16. Anti-L1CAM radioimmunotherapy is more effective with the radiolanthanide terbium-161 compared to lutetium-177 in an ovarian cancer model

    Energy Technology Data Exchange (ETDEWEB)

    Gruenberg, Juergen; Lindenblatt, Dennis; Cohrs, Susan; Fischer, Eliane [Paul Scherrer Institute, Center for Radiopharmaceutical Sciences ETH-PSI-USZ, Villigen (Switzerland); Dorrer, Holger [Paul Scherrer Institute, Laboratory of Radiochemistry and Environmental Chemistry, Villigen (Switzerland); Zhernosekov, Konstantin [ITG Isotope Technologies Garching GmbH, Garching (Germany); Koester, Ulli [Institut Laue-Langevin, Grenoble (France); Tuerler, Andreas [Paul Scherrer Institute, Laboratory of Radiochemistry and Environmental Chemistry, Villigen (Switzerland); University of Bern, Department of Chemistry and Biochemistry, Berne (Switzerland); Schibli, Roger [Paul Scherrer Institute, Center for Radiopharmaceutical Sciences ETH-PSI-USZ, Villigen (Switzerland); ETH Zurich, Department of Chemistry and Applied Biosciences, Zurich (Switzerland)

    2014-10-15

    The L1 cell adhesion molecule (L1CAM) is considered a valuable target for therapeutic intervention in different types of cancer. Recent studies have shown that anti-L1CAM radioimmunotherapy (RIT) with {sup 67}Cu- and {sup 177}Lu-labelled internalising monoclonal antibody (mAb) chCE7 was effective in the treatment of human ovarian cancer xenografts. In this study, we directly compared the therapeutic efficacy of anti-L1CAM RIT against human ovarian cancer under equitoxic conditions with the radiolanthanide {sup 177}Lu and the potential alternative {sup 161}Tb in an ovarian cancer therapy model. Tb was produced by neutron bombardment of enriched {sup 160}Gd targets. {sup 161}Tb and {sup 177}Lu were used for radiolabelling of DOTA-conjugated antibodies. The in vivo behaviour of the radioimmunoconjugates (RICs) was assessed in IGROV1 tumour-bearing nude mice using biodistribution experiments and SPECT/CT imaging. After ascertaining the maximal tolerated doses (MTD) the therapeutic impact of 50 % MTD of {sup 177}Lu- and {sup 161}Tb-DOTA-chCE7 was evaluated in groups of ten mice by monitoring the tumour size of subcutaneous IGROV1 tumours. The average number of DOTA ligands per antibody was 2.5 and maximum specific activities of 600 MBq/mg were achieved under identical radiolabelling conditions. RICs were stable in human plasma for at least 48 h. {sup 177}Lu- and {sup 161}Tb-DOTA-chCE7 showed high tumour uptake (37.8-39.0 %IA/g, 144 h p.i.) with low levels in off-target organs. SPECT/CT images confirmed the biodistribution data. {sup 161}Tb-labelled chCE7 revealed a higher radiotoxicity in nude mice (MTD: 10 MBq) than the {sup 177}Lu-labelled counterpart (MTD: 12 MBq). In a comparative therapy study with equitoxic doses, tumour growth inhibition was better by 82.6 % for the {sup 161}Tb-DOTA-chCE7 than the {sup 177}Lu-DOTA-chCE7 RIT. Our study is the first to show that anti-L1CAM {sup 161}Tb RIT is more effective compared to {sup 177}Lu RIT in ovarian cancer xenografts. These results suggest that {sup 161}Tb is a promising candidate for future clinical applications in combination with internalising antibodies. (orig.)

  17. CCDC 954774: Experimental Crystal Structure Determination : Dimethylammonium tri-terbium tris(4'-(tetrazol-2-id-5-yl)biphenyl-4-carboxylate) tetrahydroxide trihydrate unknown solvate

    KAUST Repository

    Xue, Dongxu

    2013-01-01

    An entry from the Cambridge Structural Database, the world’s repository for small molecule crystal structures. The entry contains experimental data from a crystal diffraction study. The deposited dataset for this entry is freely available from the CCDC and typically includes 3D coordinates, cell parameters, space group, experimental conditions and quality measures.

  18. CCDC 959634: Experimental Crystal Structure Determination : octakis(mu~3~-Hydroxo)-undecakis(mu~2~-2-fluorobenzoato)-(N,N-dimethylformamide)-nitrato-hexa-aqua-hexa-terbium

    KAUST Repository

    Guillerm, Vincent

    2014-01-01

    An entry from the Cambridge Structural Database, the world’s repository for small molecule crystal structures. The entry contains experimental data from a crystal diffraction study. The deposited dataset for this entry is freely available from the CCDC and typically includes 3D coordinates, cell parameters, space group, experimental conditions and quality measures.

  19. CCDC 954773: Experimental Crystal Structure Determination : Dimethylammonium tri-terbium tris(4-(tetrazol-2-id-5-yl)benzoate) tetrahydroxide trihydrate unknown solvate

    KAUST Repository

    Xue, Dongxu

    2013-01-01

    An entry from the Cambridge Structural Database, the world’s repository for small molecule crystal structures. The entry contains experimental data from a crystal diffraction study. The deposited dataset for this entry is freely available from the CCDC and typically includes 3D coordinates, cell parameters, space group, experimental conditions and quality measures.

  20. CCDC 954775: Experimental Crystal Structure Determination : Dimethylammonium tri-terbium tris(2-fluoro-4-(1H-tetrazol-5-yl)benzoate) tetrahydroxide tetradecahydrate

    KAUST Repository

    Xue, Dongxu

    2013-01-01

    An entry from the Cambridge Structural Database, the world’s repository for small molecule crystal structures. The entry contains experimental data from a crystal diffraction study. The deposited dataset for this entry is freely available from the CCDC and typically includes 3D coordinates, cell parameters, space group, experimental conditions and quality measures.

  1. CCDC 1411423: Experimental Crystal Structure Determination : catena-[dimethylammonium hexakis(mu-fumarato)-octakis(mu-hydroxo)-hexa-terbium N,N-dimethylformamide solvate hexahydrate

    KAUST Repository

    Assen, Ayalew H.

    2016-01-01

    An entry from the Cambridge Structural Database, the world’s repository for small molecule crystal structures. The entry contains experimental data from a crystal diffraction study. The deposited dataset for this entry is freely available from the CCDC and typically includes 3D coordinates, cell parameters, space group, experimental conditions and quality measures.

  2. CCDC 1410946: Experimental Crystal Structure Determination : catena-[dimethylammonium tris(mu-naphthalene-1,4-dicarboxylato)-tetrakis(mu-hydroxo)-triaqua-tri-terbium(iii) unknown solvate

    KAUST Repository

    Xue, Dongxu

    2015-01-01

    An entry from the Cambridge Structural Database, the world’s repository for small molecule crystal structures. The entry contains experimental data from a crystal diffraction study. The deposited dataset for this entry is freely available from the CCDC and typically includes 3D coordinates, cell parameters, space group, experimental conditions and quality measures.

  3. Phthalimides: Supramolecular Interactions in Crystals, Hypersensitive Solution 1H-NMR Dynamics and Energy Transfer to Europium(III and Terbium(III States

    Directory of Open Access Journals (Sweden)

    David J. Williams

    2003-07-01

    Full Text Available Detailed crystal structures and 1H-NMR characteristics of some alkylaminephthalimides, including dendritic polyphthalimides, are reported. These investigations were undertaken in order to obtain a better understanding of the relationship between solid-state supramolecular interactions, their persistence in solution and associated dynamics of magnetically hypersensitive phthalimide aromatic AA'BB'-AA'XX' proton NMR resonances. Some alkylamine phthalimides feature folded molecular geometries, which we attribute to n-π interactions among proximal amine-phthalimide sites; those alkylamine-phthalimides that have no possibility for such interactions feature fully extended phthalimide functionalities. Accordingly, alkylamine phthalimide compounds with folded solid-state geometries feature solvent and temperature dependent hypersensitive AA'BB'-AA'XX' 1H-NMR line profiles, which we attribute to the n-π interactions. Luminescence of Eu3+(5D0 and Tb3+(5D4 states show well defined metal ion environments in their complexes with dendritic phthalimides, as well as relatively weak phthalimide-lanthanide(III interactions.

  4. Analysis of tryptophan at nmoll(-1) level based on the fluorescence enhancement of terbium-gadolinium-tryptophan-sodium dodecyl benzene sulfonate system.

    Science.gov (United States)

    Liu, Shufang; Yang, Jinghe; Wu, Xia; Su, Benyu; Sun, Changxia; Wang, Feng

    2004-10-08

    It is found that Tb(3+) can react with tryptophan (Trp) and sodium dodecyl benzene sulfonate (SDBS), and emits the intrinsic fluoresence of Tb(3+). The fluorescence intensity can be enhanced by La(3+), Gd(3+), Lu(3+), Sc(3+) and Y(3+), among which Gd(3+) has the greatest enhancement. This is a new co-luminescence system. The studies indicate that in the Tb-Gd-Trp-SDBS system, there is both Tb-Trp-SDBS and Gd-Trp-SDBS complexes, and they aggregate together and form a large congeries. The fluorescence enhancement of the Tb-Gd-Trp-SDBS system is considered to originate from intramolecular and intermolecular energy transfers, and the energy-insulating sheath effect of Gd-Trp-SDBS complex. Under the optimum conditions, the enhanced intensity of fluorescence is in proportion to the concentration of Trp in the range from 4x10(-8) to 4x10(-5)moll(-1). The detection limit is 10(-9)moll(-1). The proposed method is one of the most sensitive fluoremetries of Trp.

  5. Preparation, characterization, and properties of PMMA-doped polymer film materials: a study on the effect of terbium ions on luminescence and lifetime enhancement.

    Science.gov (United States)

    Zhang, Hui-Jie; Fan, Rui-Qing; Wang, Xin-Ming; Wang, Ping; Wang, Yu-Lei; Yang, Yu-Lin

    2015-02-14

    Poly(methylmethacrylate) (PMMA) doped with Tb-based imidazole derivative coordination polymer {[Tb(3)(L)(μ(3)-OH)(7)]·H(2)O}(n) (1) (L = N,N'-bis(acetoxy)biimidazole) was synthesized and its photophysical properties were studied. The L'(L' = N,N'-bis(ethylacetate)biimidazole) ligand was synthesized by an N-alkylation reaction process followed by ester hydrolysis to produce ligand L. Polymer 1 and ligand L' have been characterized by (1)H NMR and IR spectroscopy, elemental analysis, PXRD and X-ray single-crystal diffraction. Coordination polymer 1 is the first observation of a CdCl(2) structure constructed with hydroxy groups and decorated by ligand L in lanthanide N-heterocyclic coordination polymers. In the 2D layered structure of 1, each Tb3 metal center is connected with three Tb1 and three Tb2 metal centers by seven hydroxyl groups in different directions, resulting in a six-membered ring. After doping, not only the luminescence intensity and lifetime enhanced, but also their thermal stability was increased in comparison with 1. When 1 was doped into poly(methylmethacrylate) (1@PMMA), polymer film materials were formed with the PMMA polymer matrix (w/w = 2.5%-12.5%) acting as a co-sensitizer for Tb(3+) ions. The luminescence intensity of the Tb(3+) emission at 544 nm increases when the content of Tb(3+) was 10%. The lifetime of 1@PMMA (914.88 μs) is more than four times longer than that of 1 (196.24 μs). All τ values for the doped polymer systems are higher than coordination polymer 1, indicating that radiative processes are operative in all the doped polymer films. This is because PMMA coupling with the O-H oscillators from {[Tb(3)(L)(μ(3)-OH)(7)]·H(2)O}(n) can suppress multiphonon relaxation. According to the variable-temperature luminescence (VT-luminescence) investigation, 1@PMMA was confirmed to be a stable green luminescent polymer film material.

  6. Changing Single-Molecule Magnet Properties of a Windmill-Like Distorted Terbium(III) α-Butoxy-Substituted Phthalocyaninato Double-Decker Complex by Protonation/Deprotonation.

    Science.gov (United States)

    Horii, Yoji; Horie, Yusuke; Katoh, Keiichi; Breedlove, Brian K; Yamashita, Masahiro

    2018-01-16

    Synthesis, structures, and magnetic properties of α-butoxy-substituted phthalocyaninato double-decker complexes Tb(α-obPc)2 (1-) (α-obPc: dianion of 1,4,8,11,15,18,22,25-octa(n-butoxy)phthalocyaninato) with protonated (1H), deprotonated (1[HDBU]), and diprotonated forms (1H2+) are discussed. X-ray analysis was used to confirm the position of the proton in 1H, and it was revealed that the protonation induced asymmetric distortion in 1H. In contrast, 1[HDBU] was distorted in a highly symmetric windmill-like fashion. 1H is arranged in a slipped column array in the crystal packing, whereas 1[HDBU] is arranged in a one-dimensional fashion, in which the magnetic easy axes of 1[HDBU] lie along the same line. From direct-current (dc) magnetic measurements, ferromagnetic Tb-Tb interactions occur in both 1H and 1[HDBU], and magnetic hysteresis was observed. However, the area of the magnetic hysteresis in 1[HDBU] is larger than that in 1H, meaning that magnetic relaxation time (τ) is longer in 1[HDBU]. In addition, the results of alternating-current magnetic measurements in a zero dc magnetic field indicate that τ of 1[HDBU] is longer as compared to 1H. In other words, protonation/deprotonation affects not only the molecular structures and crystal packing but also the single-molecule magnet properties.

  7. A Water-Stable Dual-Channel Luminescence Sensor for UO22+Ions Based on an Anionic Terbium(III) Metal-Organic Framework.

    Science.gov (United States)

    Ye, Junwei; Bogale, Raji F; Shi, Yangwei; Chen, Yanzhen; Liu, Xigang; Zhang, Siqi; Yang, Yaoyao; Zhao, Jianzhang; Ning, Guiling

    2017-06-07

    A stable 3D Tb III -based metal-organic framework [Tb(BPDC) 2 ]⋅(CH 3 ) 2 NH 2 (DUT-101) was synthesized, and it is the first efficient dual-channel luminescence sensor for aqueous UO 2 2+ ions. DUT-101 contains an anionic three-dimensional framework and protonated dimethylamine molecules embedded within the channels. The intense green emission of DUT-101 could be highly selectively and sensitively quenched by UO 2 2+ ions even in the presence of other competing metal ions. A possible sensing mechanism was proposed based on both suppression of luminescence resonance energy transfer and enhancement of intermolecular electron transfer. Furthermore, visual green fluorescent test papers based on DUT-101 were fabricated and could be used to discriminate UO 2 2+ ions among various metal ions. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. [?-N,N?-Bis(3-meth?oxy-2-oxidobenzyl?idene)propane-1,3-diamine]trinitratocopper(II)terbium(III) acetone solvate

    OpenAIRE

    Zhang Fang; Liu Fei

    2008-01-01

    In the title complex, [CuTb(C19H20N2O4)(NO3)3]·CH3COCH3, the CuII atom is four-coordinated by two O atoms and two N atoms from the deprotonated Schiff base in a square-planar geometry, while the TbIII atom is ten-coordinated by four O atoms from the deprotonated Schiff base and six O atoms from three bidentate nitrate anions. The compound is isostructural with the previously reported GdIII analogue [Elmali & Elerman (2004). Z. Naturforsch. Teil B, 59, 535–540], which was described ...

  9. Crystal structure of a mixed-ligand terbium(III coordination polymer containing oxalate and formate ligands, having a three-dimensional fcu topology

    Directory of Open Access Journals (Sweden)

    Chainok Kittipong

    2016-01-01

    Full Text Available The title compound, poly[(μ3-formato(μ4-oxalatoterbium(III], [Tb(CHO2(C2O4]n, is a three-dimensional coordination polymer, and is isotypic with the LaIII, CeIII and SmIII analogues. The asymmetric unit contains one TbIII ion, one formate anion (CHO2− and half of an oxalate anion (C2O42−, the latter being completed by application of inversion symmetry. The TbIII ion is nine-coordinated in a distorted tricapped trigonal–prismatic manner by two chelating carboxylate groups from two C2O42− ligands, two carboxylate oxygen atoms from another two C2O42− ligands and three oxygen atoms from three CHO2− ligands, with the Tb—O bond lengths and the O—Tb—O bond angles ranging from 2.4165 (19 to 2.478 (3 Å and 64.53 (6 to 144.49 (4°, respectively. The CHO2− and C2O42− anions adopt μ3-bridging and μ4-chelating-bridging coordination modes, respectively, linking adjacent TbIII ions into a three-dimensional 12-connected fcu topology with point symbol (324.436.56. The title compound exhibits thermal stability up to 623 K, and also displays strong green photoluminescence in the solid state at room temperature.

  10. CCDC 1410822: Experimental Crystal Structure Determination : heptakis(dimethylammonium) dodecakis(mu-hydroxo)-bis(mu-oxo)-nonaaqua-nona-terbium tris(octakis(mu-hydroxo)-triaqua-bis(2-fluorobenzoato)-bis(formato)-hexa-terbium) dodecakis(5-[(4-carboxylatophenyl)methoxy]benzene-1,3-dicarboxylate) unknown solvate

    KAUST Repository

    Alezi, Dalal

    2015-01-01

    An entry from the Cambridge Structural Database, the world’s repository for small molecule crystal structures. The entry contains experimental data from a crystal diffraction study. The deposited dataset for this entry is freely available from the CCDC and typically includes 3D coordinates, cell parameters, space group, experimental conditions and quality measures.

  11. BORONIZING OF STEEL

    OpenAIRE

    ULUKÖY, Arzum; CAN, Ahmet Çetin

    2006-01-01

    Boride layer has many advantages in comparison with traditional hardening methods. The boride layer has high hardening value and keeps it's hardeness at high temperatures, and it also shows favorible properties, such as the resistance to wear, oxidation and corrosion. The process can be applied at variety of materials, for instance steel, cast iron, cast steel, nickel and cobalt alloys and cermets. In this rewiew, boronizing process properties, boride layer on steel surfaces and specification...

  12. An Attempt to Develop the Methodology of Examining the Boron Content in Construction Materials with the Use of Eds Method

    Directory of Open Access Journals (Sweden)

    Popławski M.

    2015-04-01

    Full Text Available Borided layers are mainly produced during the process of heat-chemical treatment as a result of reactive diffusion of boron inside the material. The borided layers are particularly useful in difficult exploitation conditions. Generally, the borided layers are characterized by the increased hardness, heat resistance and good corrosion resistance. It is commonly known that the major disadvantage of X-ray microanalysis with EDS method is the difficulty in light elements analysis such as boron.

  13. Quantitative Electron-Excited X-Ray Microanalysis of Borides, Carbides, Nitrides, Oxides, and Fluorides with Scanning Electron Microscopy/Silicon Drift Detector Energy-Dispersive Spectrometry (SEM/SDD-EDS) and NIST DTSA-II.

    Science.gov (United States)

    Newbury, Dale E; Ritchie, Nicholas W M

    2015-10-01

    A scanning electron microscope with a silicon drift detector energy-dispersive X-ray spectrometer (SEM/SDD-EDS) was used to analyze materials containing the low atomic number elements B, C, N, O, and F achieving a high degree of accuracy. Nearly all results fell well within an uncertainty envelope of ±5% relative (where relative uncertainty (%)=[(measured-ideal)/ideal]×100%). Quantification was performed with the standards-based "k-ratio" method with matrix corrections calculated based on the Pouchou and Pichoir expression for the ionization depth distribution function, as implemented in the NIST DTSA-II EDS software platform. The analytical strategy that was followed involved collection of high count (>2.5 million counts from 100 eV to the incident beam energy) spectra measured with a conservative input count rate that restricted the deadtime to ~10% to minimize coincidence effects. Standards employed included pure elements and simple compounds. A 10 keV beam was employed to excite the K- and L-shell X-rays of intermediate and high atomic number elements with excitation energies above 3 keV, e.g., the Fe K-family, while a 5 keV beam was used for analyses of elements with excitation energies below 3 keV, e.g., the Mo L-family.

  14. A Study of Solar Thermal Propulsion System Enhancement via Thermal Storage and Thermal-electric Conversion

    Science.gov (United States)

    2010-03-24

    material. Molybdenum has a thermal conductivity of 138 W/mK, while rheniums is much lower at 39.6 W/mK 2 . Zirconium Boride (ZrB2) and Hafnium Boride ...14,000 Iridium 77 2739 213 147 $42,000 Niobium 41 2750 323 53.7 $170 Molybdenum 42 2896 390 138 $100 The materials listed in Table 1 do not...this paper, several materials with melting points above 3000 K are boride compounds and several of those that are not borides contain elements which

  15. BORONIZING OF STEEL

    Directory of Open Access Journals (Sweden)

    Arzum ULUKÖY

    2006-02-01

    Full Text Available Boride layer has many advantages in comparison with traditional hardening methods. The boride layer has high hardening value and keeps it's hardeness at high temperatures, and it also shows favorible properties, such as the resistance to wear, oxidation and corrosion. The process can be applied at variety of materials, for instance steel, cast iron, cast steel, nickel and cobalt alloys and cermets. In this rewiew, boronizing process properties, boride layer on steel surfaces and specifications and the factors that effect boride layer are examined

  16. BASIC RESEARCH ON THE SEPARATION OF SCANDIUM YTTRIUM, AND THE RARE EARTHS BY SOLVENT EXTRACTION.

    Science.gov (United States)

    RARE EARTH ELEMENTS, * SOLVENT EXTRACTION ), (*CHELATE COMPOUNDS, RARE EARTH ELEMENTS), PURIFICATION, ATOMIC SPECTROSCOPY, SCANDIUM, YTTRIUM, PRASEODYMIUM, SAMARIUM, EUROPIUM, GADOLINIUM, TERBIUM, FLUORINE COMPOUNDS, KETONES

  17. Mechanochemical synthesis and characterization of pure Co2B ...

    Indian Academy of Sciences (India)

    3Department of Industrial Design Engineering, Gazi University, Ankara 06500, Turkey. MS received 5 January 2016; accepted 2 February 2016. Abstract. Cobalt boride (Co2B) is a significant transition metal boride having a wide range of usage area due to its high oxidation, abrasion and corrosion resistance as well as its ...

  18. Mechanochemical synthesis and characterization of pure Co2B ...

    Indian Academy of Sciences (India)

    Cobalt boride (Co 2 B) is a significant transition metal boride having a wide range of usage area due to its high oxidation, abrasion and corrosion resistance as well as its superior electrochemical, magnetic and anisotropicproperties. In this study, pure Co2B nanocrystals were synthesized with Co, B 2 O 3 and Mg as starting ...

  19. Methods of repairing a substrate

    Science.gov (United States)

    Riedell, James A. (Inventor); Easler, Timothy E. (Inventor)

    2011-01-01

    A precursor of a ceramic adhesive suitable for use in a vacuum, thermal, and microgravity environment. The precursor of the ceramic adhesive includes a silicon-based, preceramic polymer and at least one ceramic powder selected from the group consisting of aluminum oxide, aluminum nitride, boron carbide, boron oxide, boron nitride, hafnium boride, hafnium carbide, hafnium oxide, lithium aluminate, molybdenum silicide, niobium carbide, niobium nitride, silicon boride, silicon carbide, silicon oxide, silicon nitride, tin oxide, tantalum boride, tantalum carbide, tantalum oxide, tantalum nitride, titanium boride, titanium carbide, titanium oxide, titanium nitride, yttrium oxide, zirconium boride, zirconium carbide, zirconium oxide, and zirconium silicate. Methods of forming the ceramic adhesive and of repairing a substrate in a vacuum and microgravity environment are also disclosed, as is a substrate repaired with the ceramic adhesive.

  20. A validated spectrofluorimetric method for the determination of citalopram in bulk and pharmaceutical preparations based on the measurement of the silver nanoparticles-enhanced fluorescence of citalopram/terbium complexes.

    Science.gov (United States)

    Khan, Muhammad Naeem; Shah, Jasmin; Jan, Muhammad Rasul; Lee, Sang Hak

    2013-01-01

    A simple, sensitive, and accurate spectrofluorimetric method was developed for the determination of citalopram in bulk and pharmaceutical preparations. The method is based on the enhancement of the weak fluorescence signal (FL) of the Tb (III)-citalopram system in the presence of silver nanoparticles. Fluorescence intensities were measured at 555 nm after excitation at 281 nm. Prepared silver nanoparticles (AgNPs) were characterized by UV-Visible spectra and transmission electron microscopy (TEM). Various factors affecting the formation of citalopram-Tb (III)-AgNPs complexes were studied and optimized. The fluorescence intensity versus concentration plot was linear over the range 0.02-14 μg mL(-1), with an excellent correlation coefficient of 0.9978. The limit of detection (LOD) and limit of quantification (LOQ) were found to be 7.15 × 10(-6) μg mL(-1) and 2.38 × 10(-5) μg mL(-1) respectively. The proposed method was found to have good reproducibility with a relative standard deviation of 3.66% (n = 6). The interference effects of common excipients found in pharmaceutical preparations were studied. The developed method was validated statistically by performing recoveries studies and successfully applied for the assay of citalopram in bulk powder and pharmaceutical preparations. Percent recoveries were found to range from 98.98% to 100.97% for bulk powder and from 96.57% to 101.77% for pharmaceutical preparations.

  1. A "plug-and-play" approach to the preparation of transparent luminescent hybrid materials based on poly(methyl methacrylate), a calix[4]arene cross-linking agent, and terbium ions.

    Science.gov (United States)

    Driscoll, Christopher R; Reid, Brodie L; McIldowie, Matthew J; Muzzioli, Sara; Nealon, Gareth L; Skelton, Brian W; Stagni, Stefano; Brown, David H; Massi, Massimiliano; Ogden, Mark I

    2011-04-07

    A novel methodology to prepare transparent luminescent hybrid materials is reported. Using a calixarene ionophore as a PMMA cross-linker avoids problems, such as phase segregation, and produces a polymer monolith that can be loaded with the metal ion required for luminescence post-synthesis. This approach is versatile and will simplify the production of such materials.

  2. CCDC 954772: Experimental Crystal Structure Determination : catena-(Dimethylammonium tris(mu~4~-3-fluorobiphenyl-4,4'-dicarboxylato)-tetrakis(mu~3~-hydroxo)-triaqua-tri-terbium unknown solvate)

    KAUST Repository

    Xue, Dongxu

    2013-01-01

    An entry from the Cambridge Structural Database, the world’s repository for small molecule crystal structures. The entry contains experimental data from a crystal diffraction study. The deposited dataset for this entry is freely available from the CCDC and typically includes 3D coordinates, cell parameters, space group, experimental conditions and quality measures.

  3. CCDC 1410820: Experimental Crystal Structure Determination : heptakis(dimethylammonium) heptacosa-terbium dodecakis((1,1'-biphenyl)-3,4',5-tricarboxylate) hexakis(2-fluorobenzoate) hexakis(formate) hexatriacontakis(hydroxide) bis(oxide) unknown solvate hydrate

    KAUST Repository

    Alezi, Dalal

    2015-01-01

    An entry from the Cambridge Structural Database, the world’s repository for small molecule crystal structures. The entry contains experimental data from a crystal diffraction study. The deposited dataset for this entry is freely available from the CCDC and typically includes 3D coordinates, cell parameters, space group, experimental conditions and quality measures.

  4. Terbium doped SnO2 nanoparticles as white emitters and SnO2:5Tb/Fe3O4 magnetic luminescent nanohybrids for hyperthermia application and biocompatibility with HeLa cancer cells.

    Science.gov (United States)

    Singh, Laishram Priyobarta; Singh, Ningthoujam Premananda; Srivastava, Sri Krishna

    2015-04-14

    SnO2:5Tb (SnO2 doped with 5 at% Tb(3+)) nanoparticles were synthesised by a polyol method and their luminescence properties at different annealing temperatures were studied. Characterization of nanomaterials was done by X-ray diffraction (XRD), Fourier transformation infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and vibrating sample magnetometry (VSM). XRD studies indicate that the prepared nanoparticles were of tetragonal structures. Upon Tb(3+) ion incorporation into SnO2, Sn(4+) changes to Sn(2+) and, on annealing again at higher temperature, Sn(2+) changes to Sn(4+). The prepared nanoparticles were spherical in shape. Sn-O vibrations were found from the FTIR studies. In photoluminescence studies, the intensity of the emission peaks of Tb(3+) ions increases with the increase of annealing temperature, and emission spectra lie in the region of white emission in the CIE diagram. CCT calculations show that the SnO2:5Tb emission lies in cold white emission. Quantum yields up to 38% can be obtained for 900 °C annealed samples. SnO2:5Tb nanoparticles were well incorporated into the PVA polymer and such a material incorporated into the polymer can be used for display devices. The SnO2:5Tb/Fe3O4 nanohybrid was prepared and investigated for hyperthermia applications at different concentrations of the nanohybrid. This achieves a hyperthermia temperature (42 °C) under an AC magnetic field. The hybrid nanomaterial SnO2:5Tb/Fe3O4 was found to exhibit biocompatibility with HeLa cells (human cervical cancer cells) at concentrations up to 74% for 100 μg L(-1). Also, this nanohybrid shows green emission and thus it will be helpful in tracing magnetic nanoparticles through optical imaging in vivo and in vitro application.

  5. Filmes delgados luminescentes obtidos a partir de hidroxicarbonatos de ítrio ativados por európio ou térbio Luminescent thin films obtained from ytrium hydroxycarbonates activated by terbium or europium

    Directory of Open Access Journals (Sweden)

    Emy Niyama

    2004-04-01

    Full Text Available These films were obtained by dip coating. Parameters like dislocation velocity; number of deposits, suspension concentration, and number of deposits followed or not by heat treatment between each deposit and calcination temperature were evaluated for establishing the best homogeneity. The obtained films were characterized in terms of their morphology, optical quality and photoluminescence by scanning electron microscopy (SEM, UV-vis absorption spectrophotometry and luminescence spectroscopy, respectively. The morphologic and luminescent characteristics showed dip coating as good laboratory technique for development of thin films for optical applications.

  6. Borlanmış AISI 5140 ve AISI 420 Çeliklerinin Difüzyon ve Adhezyon Davranışlarının İncelenmesi (015701) (1-8)

    OpenAIRE

    BARUT, Nusrettin; YAVUZ, Demet; KAYALI, Yusuf

    2015-01-01

    In this study, AISI 5140 steel and AISI 420 stainless steel were pack borided at 1123, 1173 and 1223 K for retention times of 2, 4 and 6 h. The morphology of the boride layers formed on the steel surfaces as a result of the experiments was investigated by optical microscopy. The hardness values were measured by a micro-hardness device and the phases formed on the layer were determined by the XRD method. The XRD analysis revealed that FeB, Fe2B, CrB and MnB phases had formed on the boride laye...

  7. Chemical Routes to Ceramics With Tunable Properties and Structures

    National Research Council Canada - National Science Library

    Sneddon, Larry G

    2006-01-01

    .... Research was focused on the development of new precursor routes to a number of ultra high temperature ceramics, including hafnium and zirconium -boride, -carbide and -nitride materials, and on the...

  8. EVALUATION OF THERMAL PROTECTIVE SYSTEMS FOR ADVANCED AEROSPACE VEHICLES. VOLUME II: APPENDICES.

    Science.gov (United States)

    AEROSPACE CRAFT, TABLES(DATA), GRAPHICS, OXIDES, BERYLLIUM, HAFNIUM COMPOUNDS, SPINEL, ZIRCONIUM COMPOUNDS, NITRIDES, CARBIDES, BORIDES , SILICIDES...GRAPHITE, NIOBIUM, MOLYBDENUM , TANTALUM, TUNGSTEN, THERMAL PROPERTIES, THERMAL PROPERTIES, SPECIFIC HEAT.

  9. Ceramic material suitable for repair of a space vehicle component in a microgravity and vacuum environment, method of making same, and method of repairing a space vehicle component

    Science.gov (United States)

    Riedell, James A. (Inventor); Easler, Timothy E. (Inventor)

    2009-01-01

    A precursor of a ceramic adhesive suitable for use in a vacuum, thermal, and microgravity environment. The precursor of the ceramic adhesive includes a silicon-based, preceramic polymer and at least one ceramic powder selected from the group consisting of aluminum oxide, aluminum nitride, boron carbide, boron oxide, boron nitride, hafnium boride, hafnium carbide, hafnium oxide, lithium aluminate, molybdenum silicide, niobium carbide, niobium nitride, silicon boride, silicon carbide, silicon oxide, silicon nitride, tin oxide, tantalum boride, tantalum carbide, tantalum oxide, tantalum nitride, titanium boride, titanium carbide, titanium oxide, titanium nitride, yttrium oxide, zirconium diboride, zirconium carbide, zirconium oxide, and zirconium silicate. Methods of forming the ceramic adhesive and of repairing a substrate in a vacuum and microgravity environment are also disclosed, as is a substrate repaired with the ceramic adhesive.

  10. Alloying-Element Loss during High-Temperature Processing of a Nickel-Base Superalloy (Preprint)

    Science.gov (United States)

    2013-01-01

    precipitates, and the fine white/gray particles are carbides and borides . ............................................. 23 Figure 2. Aluminum...diameter billet with a measured composition in weight percent of 20.4 cobalt, 12.3 chromium, 3.5 aluminum, 3.5 titanium, 2.7 molybdenum , 4.3 tungsten...comparable size, and submicron carbides and borides . A fifteen-minute heat treatment at the subsolvus temperature used in the present work (i.e

  11. Project Squid. A Program of Fundamental Research on Liquid Rocket and Pulse Jet Propulsion for the Bureau of Aeronautics and the Office of Naval Research of the Navy Department

    Science.gov (United States)

    1948-01-01

    nitrides, and borides bonded with a refractory metal is designed to indicate quickly which areas of this interesting field are most likely to yield...investigations of the more promising systems. 51 Library research furnished only data on the properties of the individual carbides, nitrides, borides ...tungsten carbide and chromium or molybdenum plloys exhibited a Widmanstatten structure, indicating reaction between the binder and the carbide

  12. Mechanisms of Recovering Low Cycle Fatigue Damage in Incoloy 901.

    Science.gov (United States)

    1979-01-01

    borides , porosity, brittle second phases, ctc.). Kim and Laird point out that in pure metals, crack initiation occurs at persistent slip bands at low...carbo-nitrides, and borides intentionally added to control the grain size, improve creep resistance, increase grain boundary strength, and to vitiate...which can be forged and machined fairly conventionally (19). Incoloy 901 has an austenitic (y-f.c.c.) iron-nickel-chromium matrix. Molybdenum

  13. Catalysis by Single Atoms: Water Gas Shift and Ethylene Hydrogenation

    Science.gov (United States)

    2009-04-20

    2007). DOI: 10.1021/jp0744811 16 Oxidative dehydrogenation of methanol to formaldehyde by isolated vanadium, molybdenum , and chromium oxide clusters...composite Some ZrB2-metal composites can form new boride phases during laser processing, especially when binder materials possess similar chemical...properties to Zr. We have observed the formation of new boride phases when Ti and Ta binder materials are used. Figure 8 shows TiB fibers spread

  14. Development Of Electro-Spark Alloying (ESA) And Thermo-Reactive Electro-Spark Surface Strengthening (TRESS) Technologies And Set Of Equipment With Attachments For Mechanization

    Science.gov (United States)

    2006-05-11

    wear-, corrosion- and oxidation resistant coatings (up to 300 µm thick) based on oxides, carbides, silicates, borides and nitrides of transition...based on carbides, borides , nitrides, intermetallides strengthened by nanoparticles. 15. SUBJECT TERMS EOARD, Electro Spark...seems reasonable to fill the pores of coatings with a solid lubricant, such as molybdenum disulfide MoS2. Due to high roughness of ES coatings, the

  15. Synthesis and investigation of CrB{sub 4}, MnB{sub 4} and new ternary chromium and rhenium manganese borides; Synthese und Untersuchung von CrB{sub 4}, MnB{sub 4} sowie neuen ternaeren Chrom- und Rheniummanganboriden

    Energy Technology Data Exchange (ETDEWEB)

    Knappschneider, Arno

    2014-10-13

    In the present work single crystals of the tetraborides of chromium and manganese have been grown and allowed a structure refinement of the compounds. Furthermore the physical characteristics for example hardness, electronic properties and magnetism were been determined. Also the ternary tetraboride phase of chromium and manganese was synthesized and a new ternary rhenium manganese diboride could be obtained.

  16. Synthesis and characterization of spherical Tb-MCM-41

    Energy Technology Data Exchange (ETDEWEB)

    Pires, Luiza H.O., E-mail: lulenapires@hotmail.co [Universidade Federal do Para, Instituto de Ciencias Exatas e Naturais, Laboratorio de Catalise e Oleoquimica, CP 479, CEP 66075-110, Belem, PA (Brazil); Queiroz, Renan M.; Souza, Ruth P.; Costa, Carlos E.F. da; Zamian, Jose R. [Universidade Federal do Para, Instituto de Ciencias Exatas e Naturais, Laboratorio de Catalise e Oleoquimica, CP 479, CEP 66075-110, Belem, PA (Brazil); Weber, Ingrid T. [Universidade Federal de Pernambuco, Centro de Ciencias Exatas e da Natureza, Av. Prof. Luis Barros Freire, s/n, Cidade Universitaria, 50670-901 Recife, PE (Brazil); Filho, Geraldo N. da Rocha [Universidade Federal do Para, Instituto de Ciencias Exatas e Naturais, Laboratorio de Catalise e Oleoquimica, CP 479, CEP 66075-110, Belem, PA (Brazil)

    2010-02-04

    Spherical MCM-41 was synthesized at room temperature and functionalized by means of direct synthesis method. Evidence for the terbium presence in the silica matrix was obtained by means of EDX. Scanning electron microscopy (SEM) micrographs showed that terbium incorporation did not change significantly MCM-41 morphology. The maintenance of the hexagonal structure was confirmed by X-ray diffraction (XRD) pattern analysis. The cell parameter increase and the surface area decrease, observed by N{sub 2} adsorption-desorption technique, were taken as evidence of terbium introduction inside the MCM-41 framework. By FT-IR spectra it was found that the main features of the silica framework were maintained. The presence of a strong absorption band centered at ca. 220 nm in the diffuse reflectance UV-vis spectra could indicate the presence of tetra-coordinated terbium in the silica network of Tb-MCM-41 samples.

  17. Therapeutic use of radioactive isotopes

    CERN Multimedia

    Caroline Duc

    2013-01-01

    In December, researchers from ISOLDE-CERN, the Paul Scherrer Institute (PSI) and the Institut Laue-Langevin (ILL) published the results of an in vivo study which successfully proved the effectiveness of four terbium isotopes for diagnosing and treating cancerous tumours.   Four terbium isotopes suitable for clinical purposes. “ISOLDE is the only installation capable of supplying terbium isotopes of such purity and intensity in the case of three out of the four types used in this study,” explains Karl Johnson, a physicist at ISOLDE.  “Producing over a thousand different isotopes, our equipment offers the widest choice of isotopes in the world!” Initially intended for fundamental physics research, ISOLDE has diversified its activities over time to invest in various projects in the materials science, biochemistry and nuclear medicine fields. The proof-of-concept study has confirmed that the four terbium isotopes 149Tb, 152Tb, 155Tb produ...

  18. Thermal History Using Microparticle Trap Luminescence

    Science.gov (United States)

    2012-06-01

    and thermoluminescence of terbium-activated silicates and aluminates " . Radiat. Meas. 43, 323-326 (2008). HDTRA1-07-1-0016 University of...of terbium-activated silicates and aluminates " . 15th Solid State Dosimetry Conference, Delft, The Netherlands, July 8-13 (2007). 2 INTRODUCTION...increased to 500°C until combustion occurred (- 7 min). The remaining powder was collected, crushed in a agate mortar, and annealed (typically at 900

  19. Microstructure and mechanical properties of a new type of austempered boron alloyed high silicon cast steel

    Directory of Open Access Journals (Sweden)

    Chen Xiang

    2013-05-01

    Full Text Available In the present paper, a new type of austempered boron alloyed high silicon cast steel has been developed, and its microstructures and mechanical properties at different temperatures were investigated. The experimental results indicate that the boron alloyed high silicon cast steel comprises a dendritic matrix and interdendritic eutectic borides in as-cast condition. The dendritic matrix is made up of pearlite, ferrite, and the interdendritic eutectic boride is with a chemical formula of M2B (M represents Fe, Cr, Mn or Mo which is much like that of carbide in high chromium white cast iron. Pure ausferrite structure that consists of bainitic ferrite and retained austenite can be obtained in the matrix by austempering treatment to the cast steel. No carbides precipitate in the ausferrite structure and the morphology of borides remains almost unchanged after austempering treatments. Secondary boride particles precipitate during the course of austenitizing. The hardness and tensile strength of the austempered cast steel decrease with the increase of the austempering temperature, from 250 篊 to 400 篊. The impact toughness is 4-11 J昪m-2 at room temperature and the impact fracture fractogragh indicates that the fracture is caused by the brittle fracture of the borides.

  20. AlM2B2 (M  =  Cr, Mn, Fe, Co, Ni): a group of nanolaminated materials

    Science.gov (United States)

    Kádas, K.; Iuşan, D.; Hellsvik, J.; Cedervall, J.; Berastegui, P.; Sahlberg, M.; Jansson, U.; Eriksson, O.

    2017-04-01

    Combining theory with experiments, we study the phase stability, elastic properties, electronic structure and hardness of layered ternary borides AlCr2B2, AlMn2B2, AlFe2B2, AlCo2B2, and AlNi2B2. We find that the first three borides of this series are stable phases, while AlCo2B2 and AlNi2B2 are metastable. We show that the elasticity increases in the boride series, and predict that AlCr2B2, AlMn2B2, and AlFe2B2 are more brittle, while AlCo2B2 and AlNi2B2 are more ductile. We propose that the elasticity of AlFe2B2 can be improved by alloying it with cobalt or nickel, or a combination of them. We present evidence that these ternary borides represent nanolaminated systems. Based on SEM measurements, we demonstrate that they exhibit the delamination phenomena, which leads to a reduced hardness compared to transition metal mono- and diborides. We discuss the background of delamination by analyzing chemical bonding and theoretical work of separation in these borides.

  1. Study on wear resistant cast B-containing 1Cr18Ni9Ti stainless steel

    Directory of Open Access Journals (Sweden)

    Kuang Jiacai

    2009-02-01

    Full Text Available The developed 1Cr18Ni9Ti austenitic stainless steel containing 1.63 wt.%B have been characterized by X-ray diffraction (XRD, electron probe microanalyzer (EPMA, optical microscopy (OM, scanning electron microscopy (SEM, energy dispersive X-ray spectroscopy (EDS and Vickers microhardness measurement. The microstructural evolution and property of high boron stainless steel after solution treatment at the temperature of 1050℃ are also investigated. The results show that the main compositions of borides are Fe, Cr and B, and with small amount of Ni, Mn and C elements. Silicon is insoluble in the borides. The hardness of borides is over 1,500 HV. It has been found that borides do not decompose during solution treatment, but part of borides dissolves into the matrix. The effect of increasing the solubility of boron element in the austenitic matrix favours the hardness enhancement by 8.54%. High boron stainless steel has excellent wear resistance in corrosive environment. Lifetime of transfer pipe made of high boron-containing stainless steel is 1.5-1.8 times longer than that of boron-free 1Cr18Ni9Ti stainless steel.

  2. Effects of Tungsten Addition on the Microstructure and Corrosion Resistance of Fe-3.5B Alloy in Liquid Zinc

    Directory of Open Access Journals (Sweden)

    Xin Liu

    2017-04-01

    Full Text Available The effects of tungsten addition on the microstructure and corrosion resistance of Fe-3.5B alloys in a liquid zinc bath at 520 °C were investigated by means of scanning electron microscopy, X-ray diffraction and electron probe micro-analysis. The microstructure evolution in different alloys is analyzed and discussed using an extrapolated Fe-B-W ternary phase diagram. Experimental results show that there are three kinds of borides, the reticular (Fe, W2B, the rod-like (Fe, W3B and flower-like FeWB. The addition of tungsten can refine the microstructure and improve the stability of the reticular borides. Besides, it is beneficial to the formation of the metastable (Fe, W3B phase. The resultant Fe-3.5B-11W (wt % alloy possesses excellent corrosion resistance to liquid zinc. When tungsten content exceeds 11 wt %, the formed flower-like FeWB phase destroys the integrity of the reticular borides and results in the deterioration of the corrosion resistance. Also, the corrosion failure resulting from the spalling of borides due to the initiation of micro-cracks in the grain boundary of borides is discussed in this paper.

  3. The Kinetics and Dry-Sliding Wear Properties of Boronized Gray Cast Iron

    Directory of Open Access Journals (Sweden)

    Dong Mu

    2013-01-01

    Full Text Available Some properties of boride formed on gray cast iron (GCI have been investigated. GCI was boronized by powder-pack method using Commercial LSB-II powders at 1123, 1173, and 1223 K for 2, 4, 6, and 8 h, respectively. Scanning electron microscopy showed that boride formed on the surface of boronized GCI had tooth-shaped morphology. The hardness of boride formed on surfaces of GCI ranged from 1619 to 1343 HV0.025, and quenched and tempered GCI ranged from 400 to 610 HV0.025. The boride formed in the coating layer confirmed by X-ray diffraction analysis was Fe2B single phase. Depending on boronizing time and temperature, the thickness of coating layers on boronized GCI ranged from 26 to 105 μm. The activation energy was 209 kJ/mol for boronized GCI. Moreover, the possibility of predicting the iso-thickness of boride layers variation was studied. Dry-sliding wear tests showed that the wear resistance of boronized sample was greater than that of quenched and tempered sample.

  4. On the quenching of trivalent terbium luminescence by ligand low lying triplet state energy and the role of the {sup 7}F{sub 5} level: The [Tb(tta){sub 3} (H{sub 2}O){sub 2}] case

    Energy Technology Data Exchange (ETDEWEB)

    Souza, A.S., E-mail: adelmosaturnino@hotmail.com [Departamento de Química Fundamental, Universidade Federal de Pernambuco, 50670-901 Recife, PE (Brazil); Nunes, L.A. [Instituto de Física de São Carlos, Universidade de São Paulo, 13560-970 São Carlos, SP (Brazil); Felinto, M.C.F.C. [Instituto de Pesquisas Energéticas e Nucleares-IPEN, 05505-800 São Paulo, SP (Brazil); Brito, H.F. [Instituto de Química, Universidade de São Paulo, 05508-900 São Paulo, SP (Brazil); Malta, O.L. [Departamento de Química Fundamental, Universidade Federal de Pernambuco, 50670-901 Recife, PE (Brazil)

    2015-11-15

    In this work we discuss the observed Tb{sup 3+} ion luminescence quenching, due to the relative ligand low lying triplet state energy, in the [Tb(tta){sub 3} (H{sub 2}O){sub 2}] compound at low and room temperature (tta=thenoyltrifluoroacetonate). Theoretical energy transfer rates, for both multipolar and exchange mechanisms, were calculated and discussed on the basis of selection rules and energy mismatch conditions from the [Tb(tta){sub 3} (H{sub 2}O){sub 2}] emission spectra. We have concluded that the exchange mechanism by far dominates, in the present case, and that the long first excited state {sup 7}F{sub 5} lifetime (in the millisecond scale) plays a crucial role in the Tb{sup 3+} luminescence quenching. - Highlights: • The energy exchange between the ligand T{sub 1} and Tb{sup 3+5}D{sub 4} levels occur by the exchange interaction. • The Tb{sup 3+} first excited {sup 7}F{sub 5} level plays a crucial role in this process due to its long lifetime. • At room temperature the energy exchanged between the {sup 5}D{sub 4} level of the Tb{sup 3+} ion and the T{sub 1} of the ligand is lost via the intersystem crossing T{sub 1} → S{sub 0} channel.

  5. Synthesis, structure, and magnetic properties of a new family of tetra-nuclear {Mn2(III)Ln2}(Ln = Dy, Gd, Tb, Ho) clusters with an arch-type topology: single-molecule magnetism behavior in the dysprosium and terbium analogues.

    Science.gov (United States)

    Chandrasekhar, Vadapalli; Bag, Prasenjit; Speldrich, Manfred; van Leusen, Jan; Kögerler, Paul

    2013-05-06

    Sequential reaction of Mn(II) and lanthanide(III) salts with a new multidentate ligand, 2,2'-(2-hydroxy-3-methoxy-5-methylbenzylazanediyl)diethanol (LH3), containing two flexible ethanolic arms, one phenolic oxygen, and a methoxy group afforded heterometallic tetranuclear complexes [Mn2Dy2(LH)4(μ-OAc)2](NO3)2·2CH3OH·3H2O (1), [Mn2Gd2(LH)4(μ-OAc)2](NO3)2·2CH3OH·3H2O (2), [Mn2Tb2(LH)4(μ-OAc)2](NO3)2·2H2O·2CH3OH·Et2O (3), and [Mn2Ho2(LH)4(μ-OAc)2]Cl2·5CH3OH (4). All of these dicationic complexes possess an arch-like structural topology containing a central Mn(III)-Ln-Ln-Mn(III) core. The two central lanthanide ions are connected via two phenolate oxygen atoms. The remaining ligand manifold assists in linking the central lanthanide ions with the peripheral Mn(III) ions. Four doubly deprotonated LH(2-) chelating ligands are involved in stabilizing the tetranuclear assembly. A magnetochemical analysis reveals that single-ion effects dominate the observed susceptibility data for all compounds, with comparably weak Ln···Ln and very weak Ln···Mn(III) couplings. The axial, approximately square-antiprismatic coordination environment of the Ln(3+) ions in 1-4 causes pronounced zero-field splitting for Tb(3+), Dy(3+), and Ho(3+). For 1 and 3, the onset of a slowing down of the magnetic relaxation was observed at temperatures below approximately 5 K (1) and 13 K (3) in frequency-dependent alternating current (AC) susceptibility measurements, yielding effective relaxation energy barriers of ΔE = 16.8 cm(-1) (1) and 33.8 cm(-1) (3).

  6. Properties of particle phases for metal-matrix-composite design.

    Science.gov (United States)

    Baron, C; Springer, H

    2017-06-01

    Successful metallurgical design of metal-matrix-composites relies on the knowledge of the intrinsic property profiles of the metal matrix and especially the compounds employed for particles, whiskers or fibres. In this work we compiled the key properties melting point, bulk modulus, shear modulus, Young׳s modulus, density, hardness, Poisson׳s ratio and structure/space group from the widespread literature data for the most relevant compound types, i.e. borides, carbo-borides, carbides, oxides, nitrides and intermetallic phases.

  7. Field Emission Cold Cathode Devices Based on Eutectic Systems

    Science.gov (United States)

    1981-07-01

    molten aluminium. Finally it should be noted that at 800C LaB6 is in equilibrium with a variety of ternary borides of molybdenum and tungsten, e.g. (Mo...alloy containing molybdenum fibres designated A77-205. The maximum current density obtained from -2 the four systems tested were: VC 5.8, TaC 0.5...Selected physical properties of refractory carbides. TABLE 2. Selected physical properties of refractory borides . TABLE 3. Selected physical properties of

  8. Direct determination of the enthalpy of formation of MoB in synthesis from simple substances in an SHS system

    Science.gov (United States)

    Lavut, E. G.; Chelovskaya, N. V.; Kashireninov, O. E.

    1993-10-01

    In a calorimetric bomb equipped with an electric microfurnace for heating a sample, self-propagating high-temperature synthesis (SHS) of molybdenum boride is realized in accordance with the reaction Mo (c) +B (amorph.)=MoB (c); the enthalpy of this reaction is measured, and the standard enthalpy of formation of molybdenum boride from metal molybdenum and crystaline boron is calculated: Δf H 0 (MoB,c,δ,β)=103.9α1.2kJ/mole.

  9. High-Temperature Ceramic Matrix Composite with High Corrosion Resistance

    Science.gov (United States)

    2010-06-02

    individual zirconium boride and, especially, molybdenum disilicide. STCU PROJECT P286 – FINAL REPORT PAGE 16 02-Jun-10 2...Fragment of XRD pattern for molybdenum silicide. Fig. 2.5. XRD pattern for USS-22+ 2 vol.% TaB2 hot-pressed samples. Fig. 2.6. XRD pattern for USS-22...P286 – FINAL REPORT PAGE 12 02-Jun-10 1. Introduction Ceramic borides , such as hafnium diboride (HfB2) and zirconium diboride (ZrB2

  10. Collaborative Research and Development (CR&D). Delivery Order 0031: Basic Research and Development of Ti-B Alloys

    Science.gov (United States)

    2006-09-01

    ingot. The boride phase formed in situ due to boron addition was confirmed to be TiB from X-ray diffraction. Detailed microstructural examination on all...rates in the range 10-5-10-1 S-1. TZM "-f 7.0 ( molybdenum -based alloy) material was procured and Fig. 2 Sample geometry grips were fabricated to...equilibrium be­ tween solute rejection at the solidification front, the forma­ tion of borides , and alloy nucleation ahead of the front. The mechanism of

  11. Molten Boron Phase-Change Thermal Energy Storage to Augment Solar Thermal Propulsion Systems

    Science.gov (United States)

    2011-07-13

    Thermodynamic Properties of Transition Metal Borides . I. The Molybdenum -boron system and Elemental Boron," Journal of Physical Chemistry, Vol. 81... Molybdenum -Boron and Some Properties of The Molybdenum - Borides ," Journal of Metals, September 1952, pp. 983-988. 40Stout, N. D., Mar, R. W., and Boo, W. O...BeO 3010 2.43 1.458 3,410 Molybdenum 2890 0.255 0.153 391 Silicon Carbide 2818 1.47 0.882 --- B4C 2673 2.51 1.506 1,900 Boron 2570 2.93 4,650

  12. Electrically conductive containment vessel for molten aluminum

    Science.gov (United States)

    Holcombe, C.E.; Scott, D.G.

    1984-06-25

    The present invention is directed to a containment vessel which is particularly useful in melting aluminum. The vessel of the present invention is a multilayered vessel characterized by being electrically conductive, essentially nonwettable by and nonreactive with molten aluminum. The vessel is formed by coating a tantalum substrate of a suitable configuration with a mixture of yttria and particulate metal 10 borides. The yttria in the coating inhibits the wetting of the coating while the boride particulate material provides the electrical conductivity through the vessel. The vessel of the present invention is particularly suitable for use in melting aluminum by ion bombardment.

  13. Phase equilibrium in system Ti-Si-C-B and synthesis of MAX phase layers in vacuum under the influence of electron beam

    Science.gov (United States)

    Smirnyagina, N. N.; Khaltanova, V. M.; Dasheev, D. E.; Lapina, A. E.

    2017-05-01

    Composite layers on the basis of carbides and borides the titan and silicon on titanic alloy VТ-1 are generated at diffused saturation by electron beam treatment in vacuum. Formation in a composite of MAX phase Ti3SiC2 is shown. Thermodynamic research of phase equilibrium in systems Ti-Si-C and Ti-B-C in the conditions of high vacuum is executed. The thermodynamics, formation mechanisms of superfirm layers borides and carbides of the titan and silicon are investigated.

  14. New Process for Grain Refinement of Aluminum. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Joseph A. Megy

    2000-09-22

    A new method of grain refining aluminum involving in-situ formation of boride nuclei in molten aluminum just prior to casting has been developed in the subject DOE program over the last thirty months by a team consisting of JDC, Inc., Alcoa Technical Center, GRAS, Inc., Touchstone Labs, and GKS Engineering Services. The Manufacturing process to make boron trichloride for grain refining is much simpler than preparing conventional grain refiners, with attendant environmental, capital, and energy savings. The manufacture of boride grain refining nuclei using the fy-Gem process avoids clusters, salt and oxide inclusions that cause quality problems in aluminum today.

  15. Reactive Chemical Vapor Deposition Method as New Approach for Obtaining Electroluminescent Thin Film Materials

    Directory of Open Access Journals (Sweden)

    Valentina V. Utochnikova

    2012-01-01

    Full Text Available The new reactive chemical vapor deposition (RCVD method has been proposed for thin film deposition of luminescent nonvolatile lanthanide aromatic carboxylates. This method is based on metathesis reaction between the vapors of volatile lanthanide dipivaloylmethanate (Ln(dpm3 and carboxylic acid (HCarb orH2Carb′ and was successfully used in case of HCarb. Advantages of the method were demonstrated on example of terbium benzoate (Tb(bz3 and o-phenoxybenzoate thin films, and Tb(bz3 thin films were successfully examined in the OLED with the following structure glass/ITO/PEDOT:PSS/TPD/Tb(bz3/Ca/Al. Electroluminescence spectra of Tb(bz3 showed only typical luminescent bands, originated from transitions of the terbium ion. Method peculiarities for deposition of compounds of dibasic acids H2Carb′ are established on example of terbium and europium terephtalates and europium 2,6-naphtalenedicarboxylate.

  16. Joint electroreduction of lanthanum, gadolinium and boron in halide melts

    Directory of Open Access Journals (Sweden)

    Khushkhov KH.B.

    2003-01-01

    Full Text Available The joint electroreduction of La, Gd and B from chloride-fluoride melts has been studied by cyclic voltametry. Based on the analysis of voltamograms the possibility of electrosynthesis of lanthanum-gadolinium borides from chloride-fluoride melts has been shown.

  17. Effect of spin polarization on the structural properties and bond ...

    Indian Academy of Sciences (India)

    Abstract. In this paper, spin and non-spin polarization (SP, NSP) are performed to study structural properties and bond hardness of FexB (x = 1, 2, ... ture toughness of iron boride layer depend on process time and temperature [5,6]. .... Mechanical and thermodynamic properties were calculated for the ferromagnetic (FM) and ...

  18. Flydende fase sintring af rustfrit stål

    DEFF Research Database (Denmark)

    Maahn, Ernst Emanuel; Mathiesen, Troels

    1998-01-01

    on addition of boride to AISI 316L type steels has previously proved to be sensitive to intergranular corrosion due to formation of intermetallic phases. In order to improve this system further, application of other alloy systems based on a higher alloyed 904L type stainless steel powder (PM 150) has been...

  19. Photovoltaic cell

    Science.gov (United States)

    Gordon, Roy G.; Kurtz, Sarah

    1984-11-27

    In a photovoltaic cell structure containing a visibly transparent, electrically conductive first layer of metal oxide, and a light-absorbing semiconductive photovoltaic second layer, the improvement comprising a thin layer of transition metal nitride, carbide or boride interposed between said first and second layers.

  20. Effect of Relative Humidity on the Tribological Properties of Self-Lubricating H3BO3 Films Formed on the Surface of Steel Suitable for Biomedical Applications

    Directory of Open Access Journals (Sweden)

    E. Hernández-Sanchez

    2015-01-01

    Full Text Available The effect of environmental humidity on the self-lubricating properties of a thin film of boric acid (H3BO3 was evaluated. H3BO4 films were successfully formed on the surface of AISI 316L steel. The study was conducted on AISI 316L steel because of its use in biomedical applications. First, the samples were exposed to boriding to generate a continuous surface layer of iron borides. The samples were then exposed to a short annealing process (SAP at 1023 K for 5 min and cooled to room temperature while controlling the relative humidity (RH. Five different RH conditions were tested. The purpose of SAP was to promote the formation of a surface film of boric acid from the boron atoms present in the iron boride layers. The presence of the boric acid at the surface of the borided layer was confirmed by Raman spectroscopy and X-ray diffraction (XRD. The self-lubricating capability of the films was demonstrated using the pin-on-disk technique. The influence of RH was reflected by the friction coefficient (FC, as the samples cooled with 20% of RH exhibited FC values of 0.16, whereas the samples cooled at 60% RH showed FC values of 0.02.

  1. Microwave synthesis of electrode materials for lithium batteries

    Indian Academy of Sciences (India)

    Unknown

    Bi4B2O9 have been used as cathodes (Jones and Akridge. 1995). ... reactive, is a superb secondary heater (Vaidhyanathan et al 1997). Researches at our laboratory and elsewhere have demonstrated the use of microwaves in the synthesis of a wide ... 1997a), silicides (Vaidhyanathan and Rao 1997b), borides. (Mingos ...

  2. The adhesion of hot-filament CVD diamond films on AISI type 316 austenitic stainless steel

    NARCIS (Netherlands)

    Buijnsters, J.G.; Shankar, P.; Enckevort, W.J.P. van; Schermer, J.J.; Meulen, J.J. ter

    2004-01-01

    Steel ball indentation and scratch adhesion testing of hot filament chemical vapour deposited diamond films onto AISI type 316 austenitic stainless steel substrates using two different interlayer systems, namely chromium nitride and borided steel, have been investigated. In order to compare the

  3. Electrospark Deposition for Depot- and Field-Level Component Repair and Replacement of Hard Chromium Plating

    Science.gov (United States)

    2008-02-01

    surfaces. Commonly used electrodes for wear and friction enhancement include sintered carbides, borides , and hard alloys such as Stellite 1, Stellite 6...Tribaloy 700 and 800, and molybdenum . The dynamic coefficient of friction of machine component surfaces can be reduced from 0.6 to less than 0.2

  4. Time-resolved Langmuir Probing of a New Lanthanum Hexaboride (LaB6) Hollow Cathode

    Science.gov (United States)

    2011-09-01

    unlike refractory metals such as tungsten and molybdenum , it is not susceptible to boron diffusion from the LaB6 insert or the boron nitride heater...2 Lafferty, J. M., “ Boride Cathodes,” Journal of Applied Physics, vol. 22, no. 3, 1951, pp. 299-309. 3 Kim, V., Popov, G., Arkhipov, B., Murashko

  5. iMAST FY2007 Annual Report

    Science.gov (United States)

    2007-01-01

    multilayer design. Completed Programs Three Molybdenum (Mo) and three Nickel (Ni) coated blades along with six copper- nickel-indium (CuNiIn) coated...gas flow metering (nitrogen, argon, acetylene, and hydrogen) for depositing metallic, nitride, boride , and carbide materials in

  6. Manufacturing Methods & Technology Project Execution Report. Second Half CY 1980

    Science.gov (United States)

    1981-03-01

    MATERIAL. 1 81 7302 PRODUCTION OF BORIDE COATED LONG LIFE TOOLS AIRFRAME COMPONENTS AND PRINTED CIRCUIT BOARDS OF FIBERGLASS AND OTHER COMPOSITES ARE...SPERRY DEVELOPED A METHOD TO VAPOR DEPOSIT MOLYBDENUM CONES + A GATE FILM IN * ON A SILICON DIOXIDE LAYER TO FORM THOUSANDS OF TINY EMITTERS. SPERRY’S

  7. DEVELOPMENT OF A HIGH TEMPERATURE LIQUID METAL SOLUTION CALORIMETER.

    Science.gov (United States)

    alloys and many inorganic compounds, including such materials as steels, refractory metal alloys, carbides, borides , and silicides. Because of the high...alumina is used for other parts. Heat is supplied through molybdenum wire resistance windings and controlled by a proportioning controller. Temperatures

  8. Characterization of natural zeolite clinoptilolite for sorption of contaminants

    Energy Technology Data Exchange (ETDEWEB)

    Xingu-Contreras, E., E-mail: nyleve-18@hotmail.com; García-Rosales, G., E-mail: gegaromx@yahoo.com.mx [Instituto Tecnológico de Toluca (Mexico); García-Sosa, I., E-mail: irma.garcia@inin.gob.mx; Cabral-Prieto, A., E-mail: agustin.cabral@inin.gob.mx; Solache-Ríos, M., E-mail: marcos.solache@inin.gob.mx [Instituto Nacional de Investigaciones Nucleares, Departamento de Química (Mexico)

    2015-06-15

    The nanoparticles technology has received considerable attention for its potential applications in groundwater treatment for the removal of various pollutants as Cadmium. In this work, iron boride nanoparticles were synthesized in pure form and in presence of homo-ionized zeolite clinoptilolite, as support material. These materials were used for removing Cd (II) from aqueous solutions containing 10, 50, 100, 150, 200, 250, 300 and 400 mg/L. The characterization of these materials was made by using X-ray Diffraction, Scanning Electron Microscopy and Mössbauer Spectroscopy. Pure iron boride particles show a broad X-ray diffraction peak centered at 45{sup ∘} (2θ), inferring the presence of nanocrystals of Fe{sub 2}B as identified from Mössbauer Spectroscopy. The size of these Fe{sub 2}B particles was within the range of 50 and 120 nm. The maximum sorption capacities for Cd (II) of iron boride particles and supported iron boride particles in homo-ionized zeolitic material were nearly 100 %. For homo-ionized zeolite and homo-ionized zeolite plus sodium borohydride was ≥ 95 %.

  9. Laser alloying of bearing steel with boron and self-lubricating addition

    Directory of Open Access Journals (Sweden)

    Kotkowiak Mateusz

    2016-12-01

    Full Text Available 100CrMnSi6-4 bearing steel has been widely used for many applications, e.g. rolling bearings which work in difficult operating conditions. Therefore, this steel has to be characterized by special properties such as high wear resistance and high hardness. In this study laser-boriding was applied to improve these properties. Laser alloying was conducted as the two step process with two different types of alloying material: amorphous boron only and amorphous boron with addition of calcium fluoride CaF2. At first, the surface was coated with paste including alloying material. Second step of the process consisted in laser re-melting. The surface of sample, coated with the paste, was irradiated by the laser beam. In this study, TRUMPF TLF 2600 Turbo CO2 laser was used. The microstructure, microhardness and wear resistance of both laser-borided layer and laser-borided layer with the addition of calcium fluoride were investigated. The layer, alloyed with boron and CaF2, was characterized by higher wear resistance than the layer after laser boriding only.

  10. Effect of preparation temperature and ions doping on size ...

    African Journals Online (AJOL)

    Binary and quaternary amorphous nano powders are prepared by wet reduction method. Cobalt boride nano catalyst is synthesized at 10 and 60 ºC. Effect of preparation temperature on size and morphology was studied. Co-M-Zr-B (M: Cr, Mo and W) as quaternary catalysts are also prepared in order to studying ions ...

  11. Doped Boron Carbide-Based Polymers: Fundamental Studies of a Novel Class of Materials for Enhanced Neutron Detection

    Science.gov (United States)

    2016-03-01

    Society 58 (2013) 147; Abstract: B16.00014; Session B16: Focus Session: Spin-Dependent Physics in Graphene , Room: 318; 1:51 PM–2:03 PM [presented by...Boron Carbide Semiconductors : So Many Devices and Applications, So Little Understanding”, 118th International Symposium on Boron, Borides and Related

  12. Molecular indicators for palaeoenvironmental change in a Messinian evaporitic sequence (Vena del Gesso, Italy) II. Stratigraphic changes in abundances and (13)C contents of free and sulphur-bound skeletons in a single marl bed

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Kenig, F.; Frewin, N.L.; Hayes, J.M.

    1995-01-01

    The extractable organic matter of 10 immature samples from a marl bed of one evaporitic cycle of the Vena del Gesso sediments (Gessoso-solfifera Fm., Messinian, Italy) was analyzed quantitatively for free hydrocarbons and organic sulphur compounds. Nickel boride was used as a desulphurizing agent to

  13. Electrochemical Corrosion Behavior of Spray-Formed Boron-Modified Supermartensitic Stainless Steel

    Science.gov (United States)

    Zepon, Guilherme; Nogueira, Ricardo P.; Kiminami, Claudio S.; Botta, Walter J.; Bolfarini, Claudemiro

    2017-04-01

    Spray-formed boron-modified supermartensitic stainless steel (SMSS) grades are alloys developed to withstand severe wear conditions. The addition of boron to the conventional chemical composition of SMSS, combined with the solidification features promoted by the spray forming process, leads to a microstructure composed of low carbon martensitic matrix reinforced by an eutectic network of M2B-type borides, which considerably increases the wear resistance of the stainless steel. Although the presence of borides in the microstructure has a very beneficial effect on the wear properties of the alloy, their effect on the corrosion resistance of the stainless steel was not comprehensively evaluated. The present work presents a study of the effect of boron addition on the corrosion resistance of the spray-formed boron-modified SMSS grades by means of electrochemical techniques. The borides fraction seems to have some influence on the repassivation kinetics of the spray-formed boron-modified SMSS. It was shown that the Cr content of the martensitic matrix is the microstructural feature deciding the corrosion resistance of this sort of alloys. Therefore, if the Cr content in the alloy is increased to around 14 wt pct to compensate for the boron consumed by the borides formation, the corrosion resistance of the alloy is kept at the same level of the alloy without boron addition.

  14. Adhesive and Cohesive Strength in FeB/Fe2B Systems

    Science.gov (United States)

    Meneses-Amador, A.; Blancas-Pérez, D.; Corpus-Mejía, R.; Rodríguez-Castro, G. A.; Martínez-Trinidad, J.; Jiménez-Tinoco, L. F.

    2018-01-01

    In this work, FeB/Fe2B systems were evaluated by the scratch test. The powder-pack boriding process was performed on the surface of AISI M2 steel. The mechanical parameters, such as yield stress and Young's modulus of the boride layer, were obtained by the instrumented indentation technique. Residual stresses produced on the boride layer were estimated by using the x-ray diffraction (XRD) technique. The scratch test was performed in order to evaluate the cohesive/adhesive strength of the FeB/Fe2B coating. In addition, a numerical evaluation of the scratch test on boride layers was performed by the finite element method. Maximum principal stresses were related to the failure mechanisms observed by the experimental scratch test. Shear stresses at the interfaces of the FeB/Fe2B/substrate system were also evaluated. Finally, the results obtained provide essential information about the effect of the layer thickness, the residual stresses, and the resilience modulus on the cohesive/adhesive strength in FeB/Fe2B systems.

  15. Role of boron addition on the consolidation and properties of steel ...

    Indian Academy of Sciences (India)

    The examinations have revealed the presence of numerous fine complex borides in the microstructure of the steel–8% TiB2 and steel–8% TiB2–1% B composites. Author Affiliations. Iwona Sulima1. Institute of Technology, Pedagogical University of Krakow, Podchorazych 2 St., 30-084 Krakow, Poland. Dates. Manuscript ...

  16. Pitting corrosion behaviour of diamond coated tool steel

    NARCIS (Netherlands)

    Buijnsters, J.G.; Subba Rao, R.V.; Shankar, P.; Enckevort, W.J.P. van; Schermer, J.J.; Gebert, A.; Meulen, J.J. ter

    2005-01-01

    Using a hot filament chemical vapour deposition reactor, diamond films of approximately 2-3 mum in thickness were deposited on tool steel specimens with three different interlayer systems, namely CrN, Si and borided steel. The morphology, defect densities and residual stresses of the diamond films

  17. Synthesis of carbon fibre-reinforced, silicon carbide composites by ...

    Indian Academy of Sciences (India)

    pyrolysis (PIP), liquid silicon infiltration (LSI), sol–gel, reaction hot-pressing, have been used for ... resin matrix and is then infiltrated with molten silicon (Krenkel 2001); but the presence of free silicon may act as a ... and (iv) finally carbothermal reduction of oxides to carbides/borides at 1873 and 1973 K for 3 h as shown by ...

  18. Quantitative assessment of mono- and polysulphide-linked carbon skeletons of S-rich macromolecular aggregates present in bitumens and oils

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Schouten, S.; Baas, M.; Kock-van Dalen, A.C.; Kohnen, M.E.L.; Leeuw, J.W. de

    1995-01-01

    Polar fractions of three immature sulphur-rich sediments and four sulphur-rich oils, all of Miocene age, were studied using two selective chemolytic methods, namely methyl lithium/methyl iodide, which selectively cleaves polysulphide bonds, and Raney nickel or nickel boride which cleave both

  19. Sadhana | Indian Academy of Sciences

    Indian Academy of Sciences (India)

    Home; Journals; Sadhana. Ibrahim Gunes. Articles written in Sadhana. Volume 38 Issue 3 June 2013 pp 513-526. Investigation of diffusion kinetics of plasma paste borided AISI 8620 steel using a mixture of B2O3 paste and B4C/SiC · Ibrahim Gunes Sukru Taktak Cuma Bindal Yilmaz Yalcin Sukru Ulker Yusuf Kayali.

  20. Spatial resolution in X-ray imaging with scintillating glass optical fiber plates

    Science.gov (United States)

    Pavan, P.; Zanella, G.; Zannoni, R.; Marigo, A.

    1993-04-01

    Some scintillating optical fiber plates, fabricated with terbium glasses are tested for their intrinsic spatial resolution under X-ray irradiation and the result is compared with a typical phosphor screen. The spatial resolution (CTF and MTF) is measured as a function of spatial frequency and the standard deviation of the corresponding Gaussian PSF is derived.

  1. PROCESS FOR THE PREPARATION OF ALLOY NANOPARTICLES COMPRISING A NOBLE AND A NON-NOBLE METAL

    DEFF Research Database (Denmark)

    2017-01-01

    The present invention concerns a chemical process for preparing nanoparticles of an alloy comprising both a noble metal, such as platinum, and a non-noble transition or lanthanide metal, such as yttrium, gadolinium or terbium. The process is carried out by reduction with hydrogen and removal...

  2. Multiplet effects in the electronic structure of heavy rare-earth metals

    NARCIS (Netherlands)

    Lebegue, S.; Svane, A.; Katsnelson, M.I.; Lichtenstein, A.I.; Eriksson, O.

    2006-01-01

    The spectroscopic properties of elemental terbium, dysprosium, holmium, and erbium are investigated using first-principles calculations taking into account intra-atomic correlation effects. In order to describe the strongly localized f electrons together with the conduction bands, we have used the

  3. Performance of 20 Ci 137Cs γ-ray Compton spectrometer for the ...

    Indian Academy of Sciences (India)

    The in-house 137Cs spectrometer is very useful for the measurement of momentum densities of heavy materials. The performance of the machine is assessed using aluminum, terbium and mercury samples and the exper- imental data from comparable apparatus. Keywords. Compton scattering; electron momentum density; ...

  4. Author Details

    African Journals Online (AJOL)

    Pengkiliya, P. Vol 67 (2014) - Articles Interaction of 3-Hydroxypicolinamide with TbIII and its Sensitizing Effect on Terbium Luminescence as a Function of pH and Medium Abstract PDF. ISSN: 0379-4350. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about ...

  5. Author Details

    African Journals Online (AJOL)

    Devi, TP. Vol 67 (2014) - Articles Interaction of 3-Hydroxypicolinamide with TbIII and its Sensitizing Effect on Terbium Luminescence as a Function of pH and Medium Abstract PDF. ISSN: 0379-4350. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL ...

  6. THz near-field Faraday imaging in hybrid metamaterials

    NARCIS (Netherlands)

    Kumar, N.; Strikwerda, A.C.; Fan, K.; Zhang, X.; Averitt, R.D.; Planken, P.C.M.; Adam, A.J.L.

    2012-01-01

    We report on direct measurements of the magnetic near-field of metamaterial split ring resonators at terahertz frequencies using a magnetic field sensitive material. Specifically, planar split ring resonators are fabricated on a single magneto-optically active terbium gallium garnet crystal.

  7. Synthesis and photoluminescence properties of CaSixOy:Tb3+ phosphors prepared using solution-combustion method

    CSIR Research Space (South Africa)

    Dejene, FB

    2011-07-01

    Full Text Available to Ca3Si2O7 as the terbium concentration increase. Broad band excitations peaking between 280 - 360 nm derived from excited states of Tb3+ ions were observed for all powders grown from various Tb compositions. The green emission peak at 545 nm due...

  8. Scanning Electron Microscope-Cathodoluminescence Analysis of Rare-Earth Elements in Magnets.

    Science.gov (United States)

    Imashuku, Susumu; Wagatsuma, Kazuaki; Kawai, Jun

    2016-02-01

    Scanning electron microscope-cathodoluminescence (SEM-CL) analysis was performed for neodymium-iron-boron (NdFeB) and samarium-cobalt (Sm-Co) magnets to analyze the rare-earth elements present in the magnets. We examined the advantages of SEM-CL analysis over conventional analytical methods such as SEM-energy-dispersive X-ray (EDX) spectroscopy and SEM-wavelength-dispersive X-ray (WDX) spectroscopy for elemental analysis of rare-earth elements in NdFeB magnets. Luminescence spectra of chloride compounds of elements in the magnets were measured by the SEM-CL method. Chloride compounds were obtained by the dropwise addition of hydrochloric acid on the magnets followed by drying in vacuum. Neodymium, praseodymium, terbium, and dysprosium were separately detected in the NdFeB magnets, and samarium was detected in the Sm-Co magnet by the SEM-CL method. In contrast, it was difficult to distinguish terbium and dysprosium in the NdFeB magnet with a dysprosium concentration of 1.05 wt% by conventional SEM-EDX analysis. Terbium with a concentration of 0.02 wt% in an NdFeB magnet was detected by SEM-CL analysis, but not by conventional SEM-WDX analysis. SEM-CL analysis is advantageous over conventional SEM-EDX and SEM-WDX analyses for detecting trace rare-earth elements in NdFeB magnets, particularly dysprosium and terbium.

  9. Performance of 20 Ci 137Cs γ-ray Compton spectrometer for the ...

    Indian Academy of Sciences (India)

    ... than the conventional 241Am Compton spectrometers. The in-house 137Cs spectrometer is very useful for the measurement of momentum densities of heavy materials. The performance of the machine is assessed using aluminum, terbium and mercury samples and the experimental data from comparable apparatus.

  10. Faraday isolator based on TSAG crystal for high power lasers.

    Science.gov (United States)

    Mironov, E A; Palashov, O V

    2014-09-22

    A Faraday isolator based on a new magneto-optical medium, TSAG (terbium scandium aluminum garnet) crystal, has been constructed and investigated experimentally. The device provides an isolation ratio of more than 30 dB at 500 W laser power. It is shown that this medium can be used in Faraday isolators for kilowatt-level laser powers.

  11. 1. Novel Dopants in Silica Based Fibers. 2. Applications of Embedded Optical Fiber Sensors in Reinforced Concrete Buildings and Structures

    Science.gov (United States)

    1990-05-20

    effects in fibers, and nonlinear phenomena in fibers. We also use NMR, ESR and Raman techniques to study incorporation of novel as well as...neodymium, erbium, holmium or terbium. These products can be vacuum dried at elevated temperature. The acac-compound is less expensive since the hfa

  12. Time-gated FRET nanoassemblies for rapid and sensitive intra- and extracellular fluorescence imaging

    NARCIS (Netherlands)

    Afsari, Hamid Samareh; Cardoso Dos Santos, Marcelina; Lindén, Stina; Chen, Ting; Qiu, Xue; van Bergen En Henegouwen, Paul M P|info:eu-repo/dai/nl/071919481; Jennings, Travis L; Susumu, Kimihiro; Medintz, Igor L; Hildebrandt, Niko; Miller, Lawrence W

    Time-gated Förster resonance energy transfer (FRET) using the unique material combination of long-lifetime terbium complexes (Tb) and semiconductor quantum dots (QDs) provides many advantages for highly sensitive and multiplexed biosensing. Although time-gated detection can efficiently suppress

  13. Bulletin of Materials Science | Indian Academy of Sciences

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 39; Issue 7. Issue front cover thumbnail. Volume 39, Issue 7. December 2016, pages 1619-1889. pp 1619-1623. Luminescence properties of terbium-doped Li 3 PO 4 phosphor for radiation dosimetry · C B PALAN N S BAJAJ S K OMANWAR · More Details Abstract ...

  14. Interaction of 3-Hydroxypicolinamide with Tb III and its Sensitizing ...

    African Journals Online (AJOL)

    Interaction of 3-Hydroxypicolinamide with Tb III and its Sensitizing Effect on Terbium Luminescence as a Function of pH and Medium. ... The complex formed exists asML2 species in which HPA behaves as anO,O,N,N-chelating ligand. The solid complex is isolated from aqueous medium and characterized employing ...

  15. Lanthanide Enhanced Luminescence (LEL) with One and Two Photon Excitation of Quantum Dyes(copyright) Lanthanide(III)-Macrocycles

    National Research Council Canada - National Science Library

    Leif, Robert C; Becker, Margie C; Bromm Jr., Al; Chen, Nanguang; Cowan, Ann E; Vallarino, Lidia M; Yang, Sean; Zucker, Robert M

    2004-01-01

    .... Preliminary studies indicate that cells stained with the europium Quantum Dye can be observed both by conventional UV laser excitation and by infrared two-photon confocal microscopy. An enhancer has been found that enables the observation of simultaneous emissions from both the europium and terbium Quantum Dyes.

  16. Kinetically inert lanthanide complexes as reporter groups for binding of potassium by 18-crown-6

    DEFF Research Database (Denmark)

    Junker, Anne Kathrine Ravnsborg; Tropiano, Manuel; Faulkner, Stephen

    2016-01-01

    in a copper(I)-catalyzed alkyne-azide cycloaddition (CuAAC) “click” reaction with azide-functionalized crown ethers. The resulting complexes were investigated using NMR and optical methods. Titrations with potassium chloride in methanol observing the sensititzed europium- and terbium-centered emissions were...

  17. Phase identification in boron-containing powder metallurgy steel using EBSD in combination with EPMA

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Ming-Wei, E-mail: mwwu@ntut.edu.tw; Cai, Wen-Zhang

    2016-03-15

    Boron (B) is extensively used to induce liquid phase sintering (LPS) in powder metallurgy (PM) steels and thereby increase the densification. The alloying elements in B-containing PM steels affect the boride phase, stability of the boride, the temperature of liquid formation, and the progress of LPS. However, the boride phase has not been systematically identified yet. The main objective of this study was to clarify the influences of alloying elements, including C, Cr, and Ni, on the boride phases using electron backscatter diffraction (EBSD) in combination with electron probe microanalysis (EPMA). Network structures consisting of ferrite, Fe{sub 2}B boride, and Fe{sub 3}C carbide were extensively observed in the Fe–0.4B–0.5C steel. The portions of Fe{sub 2}B were sufficiently larger than those of Fe{sub 3}C, and Fe{sub 3}C was mostly distributed at the interfaces between ferrite and Fe{sub 2}B. Adding 1.5 wt.% Cr or 1.8 wt.% Ni to Fe–0.4B–0.5C steel completely changes the Fe{sub 2}B and Fe{sub 3}C phases to a M{sub 3}(B,C) phase, where M represents the metallic elements, including Fe, Cr, Mo, and Ni. Furthermore, Cr, Mo, B, and C atoms tend to concentrate on the M{sub 3}(B,C) phase, but Ni atoms do not. - Highlights: • Network structures consisting of ferrite, Fe{sub 2}B boride, and Fe{sub 3}C carbide were extensively observed in the Fe–0.4B–0.5C steel. • Adding 1.5 wt.% Cr or 1.8 wt.% Ni to Fe–0.4B–0.5C steel completely transforms the Fe{sub 2}B and Fe{sub 3}C phases to a M{sub 3}(B,C) phase. • Cr, Mo, B, and C atoms tend to concentrate on the M{sub 3}(B,C) phase, but Ni atoms do not.

  18. Ternary ceramic thermal spraying powder and method of manufacturing thermal sprayed coating using said powder

    Energy Technology Data Exchange (ETDEWEB)

    Vogli, Evelina; Sherman, Andrew J.; Glasgow, Curtis P.

    2018-02-06

    The invention describes a method for producing ternary and binary ceramic powders and their thermal spraying capable of manufacturing thermal sprayed coatings with superior properties. Powder contain at least 30% by weight ternary ceramic, at least 20% by weight binary molybdenum borides, at least one of the binary borides of Cr, Fe, Ni, W and Co and a maximum of 10% by weight of nano and submicro-sized boron nitride. The primary crystal phase of the manufactured thermal sprayed coatings from these powders is a ternary ceramic, while the secondary phases are binary ceramics. The coatings have extremely high resistance against corrosion of molten metal, extremely thermal shock resistance and superior tribological properties at low and at high temperatures.

  19. Microstructure, microhardness, phase analysis and chemical composition of laser remelted FeB-Fe2B surface layers produced on Vanadis-6 steel

    Science.gov (United States)

    Bartkowska, Aneta; Swadźba, Radosław; Popławski, Mikołaj; Bartkowski, Dariusz

    2016-12-01

    The paper presents the study results of the diffusion boronized layer and their laser modification. Diffusion boronized processes were carried out on Vanadis-6 steel at 900 °C for 5 h. Boronized layers were characterized by dual-phase microstructure consisting of iron borides having a microhardness in the range from 1800 to 1400 HV. The laser heat treatment was carried out using CO2 laser after diffusion boronizing process. The research goals of this paper was analysis of microstructure, microhardness as well as phase and chemical composition of boronized layers after laser modification. Microstructure of boronized layer after laser modification consisted of remelted zone, heat affected zone and substrate. Remelted zone was characterized by microstructure consisted of boron-martensite eutectic. In this zone, the phases of borides and carbides were detected. Boronized layers after laser modification were characterized by the mild gradient of microhardness from surface to the substrate.

  20. Ceramic fibers from Si-B-C polymer precursors

    Science.gov (United States)

    Riccitiello, S. R.; Hsu, M. S.; Chen, T. S.

    1993-01-01

    Non-oxide ceramics such as silicon carbide (SiC), silicon nitride (Si3N4), and silicon borides (SiB4, SiB6) have thermal stability, oxidation resistance, hardness, and varied electrical properties. All these materials can be prepared in a fiber form from a suitable polymer precursor. The above mentioned fibers, when tested over a temperature range from 25 to 1400 C, experience degradation at elevated temperatures. Past work in ceramic materials has shown that the strength of ceramics containing both carbides and borides is sustained at elevated temperatures, with minimum oxidation. The work presented here describes the formation of ceramic fibers containing both elements, boron and silicon, prepared via the polymer precursor route previously reported by the authors, and discusses the fiber mechanical properties that are retained over the temperature range studied.

  1. RESEARCH OF PROCESS OF AN ALLOYING OF THE FUSED COATINGS RECEIVED FROM THE SUPERFICIAL ALLOYED WIRE BY BORON WITH IN ADDITIONALLY APPLIED ELECTROPLATED COATING OF CHROME AND COPPER

    Directory of Open Access Journals (Sweden)

    V. A. Stefanovich

    2015-01-01

    Full Text Available Researches on distribution of chrome and copper in the fused coating received from the superficial alloyed wire by boron with in additionally applied electroplated coating of chrome and copper were executed. The structure of the fused coating consists of dendrites on which borders the boride eutectic is located. It is established that the content of chrome in dendrites is 1,5– 1,6 times less than in the borid; distribution of copper on structure is uniformed. Coefficients of digestion of chrome and copper at an argon-arc welding from a wire electrode with electroplated coating are established. The assimilation coefficient for chrome is equal to 0,9–1,0; for copper – 0,6–0,75.

  2. Perspectives of High-Temperature Thermoelectric Applications and p-type and n-type Aluminoborides

    Science.gov (United States)

    Mori, T.

    2016-10-01

    A need exists to develop high-temperature thermoelectric materials which can utilize high-temperature unutilized/waste heat in thermal power plants, steelworks, factories, incinerators, etc., and also focused solar power. The thermal power plant topping application is of potential high impact since it can sizably increase the efficiency of power plants which are the major supply of electrical power for many countries. Higher borides are possible candidates for their particular high-temperature stability, generally large Seebeck coefficients, α, and intrinsic low thermal conductivity. Excellent (|α| > 200 μV/K) p-type or n-type behavior was recently achieved in the aluminoboride YAl x B14 by varying the occupancy of Al sites, x. Finding p-type and n-type counterparts has long been a difficulty of thermoelectric research not limited to borides. This paper reviews possible high-temperature thermoelectric applications, and recent developments and perspectives of thermoelectric aluminoborides.

  3. Liquid Phase Sintering of Highly Alloyed Stainless Steel

    DEFF Research Database (Denmark)

    Mathiesen, Troels

    1996-01-01

    of boride to AISI 316L type steels have previously been studied, but were found to be sensitive to intergranular corrosion due to formation of intermetallic phases rich in chromium and molybdenum. In order to improve this system further, new investigations have focused on the use of higher alloyed stainless......Liquid phase sintering of stainless steel is usually applied to improve corrosion resistance by obtaining a material without an open pore system. The dense structure normally also give a higher strength when compared to conventional sintered steel. Liquid phase sintrering based on addition...... steel as base material. The stainless base powders were added different amounts and types of boride and sintered in hydrogen at different temperatures and times in a laboratory furnace. During sintering the outlet gas was analyzed and subsequently related to the obtained microstructure. Thermodynamic...

  4. Peculiar structure and tensile strength of WB4: nonstoichiometric origin

    Directory of Open Access Journals (Sweden)

    Huiyang Gou

    2012-03-01

    Full Text Available Tungsten tetraboride (WB4 is experimentally considered as potentially superhard material and is therefore expected to have highly structural stability and enhanced resistance against plastic deformation and failure. The examinations of bond-deformation mechanism suggest a significantly soft bond-deformation pattern induced by ionic W-B bonding for nominal WB4 in experiments, largely responsible for the limitation of its strength and structural integrity. Computations on the structures and mechanical properties for WB4 show a novel thermodynamically favored MoB4-type phase with excellent mechanical properties and remarkable incompressibility along c direction. The illustrations of nonstoichiometry and x-ray diffraction spectra rationalize the experimental observation of nominal composition WB4 as defective tungsten borides (W1-xB3 (x0.25. The results provide new insight into the real structural and mechanical properties of tungsten borides.

  5. Evolution of microstructure of the new heat resistant 9 - 11 % Cr steels as a function of long term creep stressing

    Energy Technology Data Exchange (ETDEWEB)

    Kauffmann, F. [Stuttgart Univ. (Germany). MPA; Kern, T.U. [Siemens AG, Muehlheim (Germany). Energy Sector; Straub, S. [ALSTOM Power Systems GmbH, Mannheim (Germany); Mayer, K.H. [ALSTOM Power Systems GmbH, Nuernberg (Germany)

    2010-07-01

    The development of new creep resistant materials for higher temperatures in the field of energy generation is a key topic with high technological, economical and environmental interest. The strength and usability of typical materials in this area are 9 - 11 % Cr steels additional alloyed with Mo, W, V, Nb, N and B, which are governed by their microstructural features such as precipitations in the sub-micron range, the dislocation density, the subgrain sizes and in unfavorable cases with the formation of boride-particles. The evaluation of these features and the understanding of their correlation with the long-time creep properties is of pivotal interest in the development of improved materials. This paper will focus on two aspects: the correlation of the microstructure after long testing times with the corresponding creep properties and the measurement and possible quantification of borides in these steels. (orig.)

  6. Phase transformations in Mo-doped FINEMETs

    Energy Technology Data Exchange (ETDEWEB)

    Silveyra, Josefina M., E-mail: jsilveyra@fi.uba.a [Lab. de Solidos Amorfos, INTECIN, FIUBA-CONICET, Paseo Colon 850, (C1063ACV) Buenos Aires (Argentina); Illekova, Emilia; Svec, Peter; Janickovic, Dusan [Institute of Physics SAS, Dubravska cesta 9, 845 11 Bratislava (Slovakia); Rosales-Rivera, Andres [Laboratorio de Magnetismo y Materiales Avanzados, Facultad de Ciencias Exactas y Naturales, Universidad Nacional de Colombia, Manizales (Colombia); Cremaschi, Victoria J. [Lab. de Solidos Amorfos, INTECIN, FIUBA-CONICET, Paseo Colon 850, (C1063ACV) Buenos Aires (Argentina)

    2010-06-15

    In this paper, the phase transformations occurring during the crystallization process of FINEMETs in which Nb has been gradually replaced by Mo have been studied by a variety of techniques including DSC, DTA, TGA, XRD and TEM. The thermal stability of the alloy was deteriorated as a consequence of Mo's smaller atomic size. The gradual replacement of Nb by Mo reduced the onset temperature of Fe-Si and of the borides. The Curie temperature of the amorphous phase slightly decreased from 594 K for x=0 to 587 K for x=3. The borides compounds Fe{sub 2}B and Fe{sub 23}B{sub 6} as well as the (Nb,Mo){sub 5}Si{sub 3} phase were found to precipitate in the second and third crystallization.

  7. Microstructural characterization aluminium alloys from the addition of boron; Caracterizacao microestrutural de ligas de aluminio a partir da adicao de boro

    Energy Technology Data Exchange (ETDEWEB)

    Nunes, A.G.P.; Pipano, T.F.; Mota, M.A.; Mariano, N.A.; Ramos, E.C.T. [Universidade Federal de Alfenas (UNIFAL), Pocos de Caldas, MG (Brazil). Instituto de Ciencias e Tecnologia

    2014-07-01

    In the electrical industry, the aluminum becomes attractive because it has excellent characteristics for transmitting electricity. The liquid aluminum has in its composition transition elements (zirconium, titanium, vanadium and chromium) that interfere negatively on the quality of the product. The addition of aluminum-boron alloys have been used to remove transition metals through the formation of borides, enabling an increase in electrical conductivity. However, no detailed reports of reactions between boron, transition metals and primary aluminum engines. However, the objective is to determine the stoichiometric composition that enables an increase in electrical conductivity of an aluminum alloy. Samples with different concentrations of boron were characterized by optical emission spectrometry, electrical conductivity and X-ray diffraction. The addition of boron in excess reduces the time in the formation of borides, and enable an increase in electrical conductivity. (author)

  8. Structure et propriétés physiques de composés magnétiques de type RT12B6 et (Hf,Ta)Fe2 et leur dépendance en fonction de la pression (physique ou chimique) (R=élément de terre rare et T=élément de transition 3d)

    OpenAIRE

    Diop, Léopold Vincent Birane

    2014-01-01

    Our multidisciplinary study includes the synthesis of intermetallic compounds and the characterization of their structural and magnetic properties. Our work has focused on RT12B6 borides where R is a rare earth element or yttrium and T a 3d transition metal as well as (Hf, Ta)Fe2 Laves phases. In order to understand the physical properties of these compounds, we have implemented various external variables (temperature, magnetic field, pressure) as well as internal variables such as the chemic...

  9. On the development of a new pre-weld thermal treatment procedure for preventing heat-affected zone (HAZ) liquation cracking in nickel-base IN 738 superalloy

    Science.gov (United States)

    Ola, O. T.; Ojo, O. A.; Chaturvedi, M. C.

    2014-10-01

    Hot cracking in the heat-affected zone (HAZ) of precipitation strengthened nickel-base superalloys, such as IN 738, during fusion welding remains a major factor limiting reparability of nickel-base gas turbine components. The problem of HAZ intergranular cracking can be addressed by modifying the microstructure of the pre-weld material through thermal treatment, which requires significant understanding of the critical factors controlling cracking behaviour. The decomposition of Mo-Cr-W-and Cr-rich borides in the alloy, among other factors, has been observed to contribute significantly to non-equilibrium intergranular liquation and, hence, intergranular liquation cracking during welding. Gleeble physical simulation of HAZ microstructure has also shown that non-equilibrium liquation is more severe in the vicinity of decomposed borides in the alloy and can occur at temperatures as low as 1,150 °C. Although currently existing pre-weld heat treatments for IN 738 superalloy minimize the contributions of dissolution of second phases, including borides, to HAZ intergranular liquation, these heat treatments are not industrially feasible due to process-related difficulties. Therefore, a new industrially feasible and effective pre-weld thermal treatment process, designated as FUMT, was developed during the present research by controlling both the formation of borides and the segregation of boron at the grain boundaries in the pre-weld heat-treated material. This thermal treatment was observed to very significantly reduce intergranular HAZ cracking in welded IN 738 superalloy. The details of the development process and developed procedure are presented in this paper.

  10. Thermisch stabiler Multilayer-Spiegel fuer den EUV-Spektralbereich

    OpenAIRE

    Benoit, N.; Feigl, T.; Yulin, S.; Kaiser, N.

    2007-01-01

    WO2006066563 A UPAB: 20060724 NOVELTY - A multilayer mirror (1) has a number of alternating molybdenum layers (4) and silicon layers (3). A barrier layer (5) is placed on a number of boundary surfaces between the molybdenum layers and the silicon layers and contains a silicon nitride or a silicon boride. A high thermal stability, particularly a high long-time stability at temperatures of greater than 3000 deg. C with a simultaneously high degree of reflection of the multilayer mirror is achie...

  11. Platinum Group Coatings for Refractory Metals

    Science.gov (United States)

    1984-06-01

    molybdenum , tungsten, tantalum, niobium, rhenium or carbon/carbon must be used to fabricate the parts to withstand these temperatures. These materials and...layers (eg silicides, borides ) o Alloy coatings that form compact oxide layers (Ni and Co F based alloys) o Stable oxides that provide physical barriers...thermally etched) surface and seems to promote adhesion. Molybdenum rods 3mm in diameter were used as substrates during many of the runs where the

  12. Reactive Processing and Co-Extrusion of Ultra-High Temperature Ceramics and Composites

    Science.gov (United States)

    2006-02-28

    Faenza, Italy. Ultra-high temperature ceramics (UHTCs) are a unique class of materials with melting temperatures in excess of 3000’C. The borides ...composites with silicon carbide (SiC) and molybdenum disilicide (MoSi 2) were examined. Two main approaches were pursued: 1) the use of reactive processing...Diboride- Molybdenum Disilicide Ceramics," pp. 299-308 in Advances in Ceramic Matrix Composites IX, Ceramic Transactions, Volume 153, ed. by N.P. Bansal, J.P

  13. Demonstration of Shear Localization in Ultrafine Grained Tungsten Alloys via Powder Metallurgy Processing Route

    Science.gov (United States)

    2012-09-01

    which remained elastic during each experiment. Interfaces between the specimen and platens were lubricated with molybdenum disulfide (MoS2) grease to...of a di-tungsten boride (W2B) phase was not detected in the nW-B sample, but the low concentration of boron may have made this phase undetectable by...Further Studies on Rhenium Alloying Effects in Molybdenum , Tungsten, and Chromium, Battelle Memorial Inst., Columbus, Ohio, 1960. 20. Lassner, E

  14. Computer Modeling of Basic Physico-Chemical Processes for DSEC Composites of System LaB6-MeB2(MeTi, Zr, Hf) at Macro-, Meso- and Microstructure Scales

    Science.gov (United States)

    2010-07-15

    single crystals of borides of rare earth metals is performed by a few labs of the world - Japan, USA, Germany, Russia, Ukraine, and the methods of...software is developed on the base of experience gained in numerical multifractal analysis of images of structures of metals and alloys during a number...of experiment on blackening of separate white squares of carpet (one per image) were obtained. The program calculated all images; fractal dimension

  15. Method to produce catalytically active nanocomposite coatings

    Science.gov (United States)

    Erdemir, Ali; Eryilmaz, Osman Levent; Urgen, Mustafa; Kazmanli, Kursat

    2016-02-09

    A nanocomposite coating and method of making and using the coating. The nanocomposite coating is disposed on a base material, such as a metal or ceramic; and the nanocomposite consists essentially of a matrix of an alloy selected from the group of Cu, Ni, Pd, Pt and Re which are catalytically active for cracking of carbon bonds in oils and greases and a grain structure selected from the group of borides, carbides and nitrides.

  16. Magnetic properties (Communication arising): Parasitic ferromagnetism in a hexaboride?

    Science.gov (United States)

    Matsubayashi, K.; Maki, M.; Tsuzuki, T.; Nishioka, T.; Sato, N. K.

    2002-11-01

    Surprisingly for a compound with no magnetic element, Young et al. have observed ferromagnetism in calcium hexaboride (CaB6) doped with lanthanum (La) - the system has a ferromagnetic Curie temperature as high as 600 K, which is comparable to that of transition-metal ferromagnets such as iron (Fe). Here we show that high-temperature ferromagnetism in this CaB6 system is not intrinsic but that it is instead due to alien phases of iron and boride.

  17. Method to produce catalytically active nanocomposite coatings

    Energy Technology Data Exchange (ETDEWEB)

    Erdemir, Ali; Eryilmaz, Osman Levent; Urgen, Mustafa; Kazmanli, Kursat

    2017-12-19

    A nanocomposite coating and method of making and using the coating. The nanocomposite coating is disposed on a base material, such as a metal or ceramic; and the nanocomposite consists essentially of a matrix of an alloy selected from the group of Cu, Ni, Pd, Pt and Re which are catalytically active for cracking of carbon bonds in oils and greases and a grain structure selected from the group of borides, carbides and nitrides.

  18. Manhattan Project Technical Series The Chemistry of Uranium (I) Chapters 1-10

    Energy Technology Data Exchange (ETDEWEB)

    Rabinowitch, E. I. [Argonne National Laboratory (ANL), Argonne, IL (United States); Katz, J. J. [Argonne National Laboratory (ANL), Argonne, IL (United States)

    1946-09-30

    This constitutes Chapters 1 through 10. inclusive, of The Survey Volume on Uranium Chemistry prepared for the Manhattan Project Technical Series. Chapters are titled: Nuclear Properties of Uranium; Properties of the Uranium Atom; Uranium in Nature; Extraction of Uranium from Ores and Preparation of Uranium Metal; Physical Properties of Uranium Metal; Chemical Properties of Uranium Metal; Intermetallic Compounds and Alloy systems of Uranium; the Uranium-Hydrogen System; Uranium Borides, Carbides, and Silicides; Uranium Nitrides, Phosphides, Arsenides, and Antimonides.

  19. Hybrid fiber and nanopowder reinforced composites for wind turbine blades

    Directory of Open Access Journals (Sweden)

    Nikoloz M. Chikhradze

    2015-01-01

    Full Text Available The results of an investigation into the production of wind turbine blades manufactured using polymer composites reinforced by hybrid (carbon, basalt, glass fibers and strengthened by various nanopowders (oxides, carbides, borides are presented. The hybrid fiber-reinforced composites (HFRC were manufactured with prepreg technology by molding pre-saturated epoxy-strengthened matrix-reinforced fabric. Performance of the manufactured composites was estimated with values of the coefficient of operating condition (COC at a moderate and elevated temperature.

  20. Microstructure characteristics of high borated stainless steel fabricated by hot-pressing sintering

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Xuan; Wang, Mingjia, E-mail: mingjiawangysu@126.com; Zhao, Hongchang

    2016-04-25

    The present study investigated the microstructure of powder metallurgy (P/M) high borated stainless steel through hot-pressing sintering in a temperature range of 1000–1150 °C within 30 min under 30 MPa. Microstructure and phase examinations were carried out by applying scanning electron microscope, electron backscatter diffraction and X-ray diffraction analysis. The results of as-atomized powders demonstrated that many powders kept egg-type structure with an austenite outer layer and the eutectic borides were much finer than those in traditional cast products. Microstructure studies revealed that borides suffered Ostwald ripening and were significantly influenced by the sintering temperature. Orientation maps indicated that the inter-particle contact areas consisted of equiaxed grains and the regions consisting of large elongated grains partly inherited the microstructure characteristics of as-atomized powder particles. Furthermore, the mechanisms governing the morphological changes in microstructure were discussed. - Highlights: • Near-complete densification could be obtained through hot-pressing sintering. • There was no phase transformation and present phases were M{sub 2}B and austenite. • Borides suffered Ostwald ripening and were significantly influenced by temperature. • Inter-particle contact areas consisted of equiaxed grains for recrystallization. • Deformation-free zones exhibited elongated grains for dendritic arms coarsening.

  1. Peculiar features of metallurgical processes at plasma-arc spraying of coatings, made of steel wire with powder fillers B4C and B4C+ZrO2

    Directory of Open Access Journals (Sweden)

    Георгій Михайлович Григоренко

    2016-11-01

    Full Text Available The interaction of metallurgical processes occurring in plasma-arc spraying between the steel shell and the carbide fillers of B4C and B4C cored wires with the addition of nanocrystalline ZrO2 powder has been analyzed. Iron-boron compounds alloyed with carbon are formed in ingots as a result of ferritiс coating of wire interacrion with fillers while the ferritic matrix contains boride and carboboride eutectics. Average microhardness of the carboboride compounds and the matrix is high – 17,78; 16,40 and 8,69; 9,95 GPa for the ingots with с B4C and B4C+ZrO2 respectively. The best quality coatings with low porosity (~1%, lamellar structure consisting of ferrite matrix reinforced with dispersed Fe borides, were obtained at a higher heat input (plasmatron current 240-250 A. The average amount of oxides in the coatings makes 15%. 0,5% addition of nanopowder ZrO2 accelerates dispersed iron-boron compounds forming, promotes their uniform distribution in the structure and improves coating microhardness up to 7,0 GPa. Application of the differential thermal analysis method to simulate the interaction processes between the steel shell and the filler during the heating of wire in the shielding gas makes it possible to promote formation of new phases (borides and carboborides of iron and to predict the phase composition of the coatings

  2. Nanostructuring of Strontium Hexaboride via Lithiation.

    Science.gov (United States)

    Ramachandran, Roshini; Salguero, Tina T

    2017-12-19

    We describe the top-down nanostructuring of a metal boride using SrB6 as an example. To accomplish this transformation, we demonstrate (1) the direct lithiation of a metal boride using n-butyllithium and then (2) the reactive disassembly of Li-SrB6 into nanoparticles using water. The identity of the Li-SrB6 intermediate, a mixture of Li2B6, LixSr1-2xB6, and SrB6 phases, was established by powder X-ray diffraction (PXRD), solid-state 11B and 7Li NMR, transmission electron microscopy, selected-area electron diffraction, and scanning electron microscopy. The necessary 2Li+/Sr2+ substitution is enabled by cation mobility within the hexaboride lattice. The subsequent reaction with water results in Li2B6 decomposition and the release of <100 nm SrB6 nanoparticles, which were characterized by PXRD, solid-state 11B and 7Li NMR, and high-resolution TEM. This chemistry opens new solution-based modification and processing options for metal borides.

  3. Microstructure and Mechanical Properties of Wide-gap Brazed Joints of K465 Alloy Using Cobalt-base Brazing Alloy

    Directory of Open Access Journals (Sweden)

    PAN Hui

    2017-06-01

    Full Text Available Vacuum brazing of K465 superalloy was carried out by using Co45NiCrWB cobalt-base filler metal at 1220 ℃ for different holding time, and the joint clearance was 0.5 mm pre-filled with FGH95 nickel-base superalloy powder. The effect of the structural constitution of brazed different holding time of temperature on the brazed joint microstructure and properties. The results show that the brazing seam is composed of alloy powder particles and borides among them. It is two-phase structure of γ and γ' with a few small blocks of borides in the powder particles, and there exists phases rich in Cr, W and Nb elements. The powder particles are growing along the holding time during the brazing process, while their combination is expanded. It is good for stress rapture properties of joints that borides was fine in brazing seam with more superalloy powder and proper holding time. And the joints brazed for 30-60 min show higher stress rapture properties.

  4. Hardness and wear resistance of steel-based surface composites fabricated with Fe-based metamorphic alloy powders by high-energy electron beam irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Kyuhong [Center for Advanced Aerospace Materials, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of); Nam, Duk-Hyun [Center for Advanced Aerospace Materials, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of); Lee, Sunghak [Center for Advanced Aerospace Materials, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of)]. E-mail: shlee@postech.ac.kr; Kim, Choongnyun Paul [Center for Advanced Aerospace Materials, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of)

    2006-07-25

    In this study, steel-based surface composites were fabricated with Fe-based metamorphic alloy powders by high-energy electron beam irradiation, and their microstructure, hardness, and wear resistance were investigated. Two kinds of Fe-based metamorphic powders were deposited on a plain carbon steel substrate, and then electron beam was irradiated on these powders to fabricate one-layered surface composites. Two-layered surface composites were also fabricated by irradiating electron beam again onto the powders deposited on the one-layered surface composites. The composite layers of 2.6-3.1 mm in thickness were homogeneously formed without defects, and contained a large amount (up to 64 vol.%) of Cr{sub 2}B or Cr{sub 1.65}Fe{sub 0.35}B{sub 0.96} borides in the Cr{sub 0.19}Fe{sub 0.7}Ni{sub 0.11} or martensite matrix. Since the hardness and wear resistance of the surface composite layers were directly influenced by hard borides, they were two to four times greater than those of the steel substrate. These borides also played a role in improving the high-temperature hardness because they are insoluble and thermally stable even at high temperatures. These findings suggested that various applications of the fabricated surface composites to materials requiring high resistance to heat and abrasion were expected.

  5. Luminescent properties of Al{sub 2}O{sub 3}: Tb powders; Propiedades luminiscentes de polvos de Al{sub 2}O{sub 3}: Tb

    Energy Technology Data Exchange (ETDEWEB)

    Esparza G, A.E.; Garcia, M.; Falcony, C.; Azorin N, J. [CICATA-IPN, Legaria 694, Col. Irrigacion, 11500 Mexico D.F. (Mexico)

    2000-07-01

    In this work the photo luminescent and cathode luminescent characteristics of aluminium oxide (Al{sub 2}O{sub 3}) powders impurified with terbium (Tb) were studied for their use in dosimetry. The optical, structural, morphological characteristics of the powders as function of variation in the impurity concentration and the annealing temperature will be presented. As regards the optical properties of powders (photoluminescence and cathode luminescence) it was observed a characteristic emission associated with radiative transitions between electron energy levels of terbium, the spectra associated with this emission consists of several peaks associated with such transitions. In the structural and morphological characterization (X-ray diffraction and scanning electron microscopy) it was appreciated that in accordance the annealing temperature of powders is augmented it is evident the apparition of certain crystalline phases. The results show that this is a promissory material for radiation dosimetry. (Author)

  6. Plastic optical fibre sensor for in-vivo radiation monitoring during brachytherapy

    Science.gov (United States)

    Woulfe, P.; Sullivan, F. J.; Lewis, E.; O'Keeffe, S.

    2015-09-01

    An optical fibre sensor is presented for applications in real-time in-vivo monitoring of the radiation dose a cancer patient receives during seed implantation in Brachytherapy. The sensor is based on radioluminescence whereby radiation sensitive scintillation material is embedded in the core of a 1mm plastic optical fibre. Three scintillation materials are investigated: thallium-doped caesium iodide (CsI:Tl), terbium-doped gadolinium oxysulphide (Gd2O2S:Tb) and europium-doped lanthanum oxysulphide (La2O2S:Eu). Terbium-doped gadolinium oxysulphide was identified as being the most suitable scintillator and further testing demonstrates its measureable response to different activities of Iodine-125, the radio-active source commonly used in Brachytherapy for treating prostate cancer.

  7. [Luminescent cytochemical methods of detecting microorganisms].

    Science.gov (United States)

    Ivanovskaia, N P; Osin, N S; Khramov, E N; Zlobin, V N

    1999-01-01

    The paper shows that the luminescence cytochemical technique can be used for identification of microorganisms and microbiological synthesis products. The method is based on the interaction of specific fluorescence probes (ANS, terbium ions, and beta-diketonate complexes of europium, as well as metal-containing porphyrines) with major microbial intracellular components and toxins. Unlike classical microbiological, immunochemical or biochemical methods of detection, the proposed method has a reasonable versatility, specificity, sensitivity, rapid action, and possible automation.

  8. Radiotherapy dosimetry based on plastic optical fibre sensors

    Science.gov (United States)

    O'Keeffe, S.; Grattan, M.; Hounsell, A.; McCarthy, D.; Woulfe, P.; Cronin, J.; Lewis, E.

    2013-05-01

    The use of a PMMA based plastic optical fibre in radiotherapy dosimetry is presented. The optical fibre tip is coated with a scintillation material, terbium-doped gadolinium oxysulfide (Gd2O2S:Tb), which fluoresces under ionising radiation. The emitted signal penetrates the fibre and propagates along the fibre where it is remotely monitored using a fluorescence spectrometer. The results demonstrate good repeatability, with a maximum percentage error of 0.59% and the response is independent of dose rate.

  9. Luminescent Lanthanide Metal Organic Frameworks for cis-Selective Isoprene Polymerization Catalysis

    OpenAIRE

    Samantha Russell; Thierry Loiseau; Christophe Volkringer; Marc Visseaux

    2015-01-01

    In this study, we are combining two areas of chemistry; solid-state coordination polymers (or Metal-Organic Framework—MOF) and polymerization catalysis. MOF compounds combining two sets of different lanthanide elements (Nd3+, Eu3+/Tb3+) were used for that purpose: the use of neodymium was required due to its well-known catalytic properties in dienes polymerization. A second lanthanide, europium or terbium, was included in the MOF structure with the aim to provide luminescent properties. Sev...

  10. Modeled Neutron Induced Nuclear Reaction Cross Sections for Radiochemsitry in the region of Thulium, Lutetium, and Tantalum I. Results of Built in Spherical Symmetry in a Deformed Region

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, R. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2013-09-06

    We have developed a set of modeled nuclear reaction cross sections for use in radiochemical diagnostics. Systematics for the input parameters required by the Hauser-Feshbach statistical model were developed and used to calculate neutron induced nuclear reaction cross sections for targets ranging from Terbium (Z = 65) to Rhenium (Z = 75). Of particular interest are the cross sections on Tm, Lu, and Ta including reactions on isomeric targets.

  11. Factors Affecting the Efficiency of Excited-States Interactions of Complexes between Some Visible Light-Emitting Lanthanide Ions and Cyclophanes Containing Spirobiindanol Phosphonates

    Directory of Open Access Journals (Sweden)

    M. S. Attia

    2007-01-01

    Full Text Available The efficiency of excited-states interactions between lanthanide ions Tb3+ and Eu3+ and some new cyclophanes (I, II, and III has been studied in different media. High luminescence quantum yield values for terbium and europium complexes in DMSO and PMMA were obtained. The photophysical properties of the green and red emissive Tb3+ and Eu3+ complexes have been elucidated, respectively.

  12. The effect of core and lanthanide ion dopants in sodium fluoride-based nanocrystals on phagocytic activity of human blood leukocytes

    Science.gov (United States)

    Sojka, Bartlomiej; Liskova, Aurelia; Kuricova, Miroslava; Banski, Mateusz; Misiewicz, Jan; Dusinska, Maria; Horvathova, Mira; Ilavska, Silvia; Szabova, Michaela; Rollerova, Eva; Podhorodecki, Artur; Tulinska, Jana

    2017-02-01

    Sodium fluoride-based β-NaLnF4 nanoparticles (NPs) doped with lanthanide ions are promising materials for application as luminescent markers in bio-imaging. In this work, the effect of NPs doped with yttrium (Y), gadolinium (Gd), europium (Eu), thulium (Tm), ytterbium (Yb) and terbium (Tb) ions on phagocytic activity of monocytes and granulocytes and the respiratory burst was examined. The surface functionalization of leukocytes and respiratory burst of cells was observed for limited number of samples.

  13. The effect of metal distribution on the luminescence properties of mixed-lanthanide metal-organic frameworks.

    Science.gov (United States)

    Cadman, Laura K; Mahon, Mary F; Burrows, Andrew D

    2018-02-13

    A series of lanthanide metal-organic frameworks (MOFs) of the general formula [Ln(Hodip)(H 2 O)]·nH 2 O (Sm, 1; Eu, 2; Gd, 3; Tb, 4; Dy, 5; Er, 6; H 4 odip = 5,5'-oxydiisophthalic acid) have been prepared and shown crystallographically to have isostructural three-dimensional frameworks. The fluorescence emission spectra of the europium compound 2, which is red, and the terbium compound 4, which is green, show characteristic peaks for transitions involving the metal centres, whereas that for the gadolinium compound 3 is dominated by transitions involving Hodip. Using a 1 : 1 : 1 mixture of europium, gadolinium and terbium nitrates in the synthesis resulted in the mixed-metal MOF [Gd 0.17 Tb 0.19 Eu 0.64 (Hodip)(H 2 O)]·nH 2 O 7, for which the ratio of the metal ions was determined using EDX spectroscopy. The fluorescence emission spectrum of 7 is dominated by europium emission bands reflecting the higher proportion of Eu 3+ centres and quenching of the terbium fluorescence by metal-to-metal energy transfer. A series of core-shell MOF materials based on the Ln(Hodip)(H 2 O) framework have been prepared in order to isolate the lanthanides in different domains within the crystals. The emission spectra for materials with Gd@Tb@Eu (8) and Tb@Eu@Gd (9) are dominated by terbium emissions, suggesting that physical separation from europium suppresses quenching. In contrast, the material with Eu@Gd@Tb (10) shows only broad ligand bands and europium emissions. This confirms that core-shell MOFs have different fluorescence properties to simple mixed-metal MOFs, demonstrating that the spatial distribution of the metals within a mixed-lanthanide MOF affects the fluorescence behaviour.

  14. Synthesis and stimulated luminescence property of Zn(BO2)2:Tb(3).

    Science.gov (United States)

    Del Rosario, G Cedillo; Cruz-Zaragoza, E; Hipólito, M García; Marcazzó, J; Hernández A, J M; Murrieta S, H

    2017-09-01

    Zinc borate, Zn(BO2)2, doped with different concentrations of terbium (0.5-8mol%) was synthesized and polycrystalline samples were characterized by Scanning Electron Microscopy and X-Ray Diffraction. The Zn(BO2)2 was formed in the pure samples sintered at 750 and 800°C which has the body centered cubic structure, and a ZnB4O7 primitive orthorhombic phase was present. The thermoluminescent intensity was dependents on the thermal treatment (250-500°C) and also on the impurity concentration. The linear dose-response was obtained between 0.022-27.7Gy and 0.5-50Gy when the samples were exposed to beta and gamma radiation, respectively. The complex structure of the glow curves was analyzed by the Computerized Glow Curve Deconvolution method. The kinetics parameters were calculated assuming the general order kinetics model describing accurately the TL process. The glow curves of Tb(3+)-doped zinc borate phosphor were well deconvolved by six glow peaks. Zinc borate with 8mol% of impurity concentration exhibited an intense radioluminescent emission. The radioluminescent spectra show their maximum bands at 370, 490, 545 and 700nm related to the terbium ion in the zinc borate. These obtained results suggest that the terbium doped zinc borate is a promising phosphor for use in radiation dosimetry because of its high TL sensitivity to the ionizing radiation. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Effect of Ising-type Tb3+ ions on the low-temperature magnetism of La, Ca cobaltite.

    Science.gov (United States)

    Knížek, K; Jirák, Z; Hejtmánek, J; Veverka, M; Kaman, O; Maryško, M; Santavá, E; André, G

    2014-03-19

    Crystal and magnetic structures of the x = 0.2 member of the La0.8-xTbxCa0.2CoO3 perovskite series have been determined from powder neutron diffraction. Enhancement of the diffraction peaks due to ferromagnetic or cluster glass ordering is observed below TC = 55 K. The moments first evolve on Co sites, and ordering of Ising-type Tb(3+) moments is induced at lower temperatures by a molecular field due to Co ions. The final magnetic configuration is collinear Fx for the cobalt subsystem, while it is canted FxCy for terbium ions. The rare-earth moments align along local Ising axes within the ab-plane of the orthorhombic Pbnm structure. The behavior in external fields up to 70-90 kOe has been probed by magnetization and heat capacity measurements. The dilute terbium ions contribute to significant coercivity and remanence that both steeply increase with decreasing temperature. A remarkable manifestation of the Tb(3+) Ising character is the observation of a low-temperature region with an anomalously large linear term of heat capacity and its field dependence. Similar behaviors are detected also for other terbium dopings x = 0.1 and 0.3.

  16. Luminescence enhancement by energy transfer in melamine-Y{sub 2}O{sub 3}:Tb{sup 3+} nanohybrids

    Energy Technology Data Exchange (ETDEWEB)

    Stagi, Luigi, E-mail: luigi.stagi@dsf.unica.it; Chiriu, Daniele; Carbonaro, Carlo M.; Ricci, Pier Carlo [Dipartimento di Fisica, Università degli Studi di Cagliari, S.P. Monserrato-Sestu Km 0,700, 09042 Monserrato (Italy); Ardu, Andrea; Cannas, Carla [Departimento di Scienze Chimiche e Geologiche and INSTM, Università d Cagliari, SS 554 bivio Sestu, I-09042 Monserrato (Italy)

    2015-09-28

    The phenomenon of luminescence enhancement was studied in melamine-Y{sub 2}O{sub 3}:Tb hybrids. Terbium doped Y{sub 2}O{sub 3} mesoporous nanowires were synthesized by hydrothermal method. X-ray diffraction patterns and Raman scattering spectra testified the realization of a cubic crystal phase. Organic-inorganic melamine-Y{sub 2}O{sub 3}:Tb{sup 3+} hybrid system was successfully obtained by vapour deposition method. Vibration Raman active modes of the organic counterpart were investigated in order to verify the achievement of hybrid system. Photoluminescence excitation and photoluminescence spectra, preformed in the region between 250 and 350 nm, suggest a strong interaction among melamine and Terbium ions. In particular, a remarkable improvement of {sup 5}D{sub 4}→ F{sub J} Rare Earth emission (at about 542 nm) of about 10{sup 2} fold was observed and attributed to an efficient organic-Tb energy transfer. The energy transfer mechanism was studied by the use of time resolved photoluminescence measurements. The melamine lifetime undergoes to a significant decrease when adsorbed to oxide surfaces and it was connected to a sensitization mechanism. The detailed analysis of time decay profile of Terbium radiative recombination shows a variation of double exponential law toward a single exponential one. Its correlation with surface defects and non-radiative recombination was thus discussed.

  17. Boron: Enabling Exciting Metal-Rich Structures and Magnetic Properties.

    Science.gov (United States)

    Scheifers, Jan P; Zhang, Yuemei; Fokwa, Boniface P T

    2017-09-19

    Boron's unique chemical properties and its reactions with metals have yielded the large class of metal borides with compositions ranging from the most boron-rich YB66 (used as monochromator for synchrotron radiation) up to the most metal-rich Nd2Fe14B (the best permanent magnet to date). The excellent magnetic properties of the latter compound originate from its unique crystal structure to which the presence of boron is essential. In general, knowing the crystal structure of any given extended solid is the prerequisite to understanding its physical properties and eventually predicting new synthetic targets with desirable properties. The ability of boron to form strong chemical bonds with itself and with metallic elements has enabled us to construct new structures with exciting properties. In recent years, we have discovered new boride structures containing some unprecedented boron fragments (trigonal planar B4 units, planar B6 rings) and low-dimensional substructures of magnetically active elements (ladders, scaffolds, chains of triangles). The new boride structures have led to new superconducting materials (e.g., NbRuB) and to new itinerant magnetic materials (e.g., Nb6Fe1-xIr6+xB8). The study of boride compounds containing chains (Fe-chains in antiferromagnetic Sc2FeRu5B2), ladders (Fe-ladders in ferromagnetic Ti9Fe2Rh18B8), and chains of triangles (Cr3 chains in ferrimagnetic and frustrated TiCrIr2B2) of magnetically active elements allowed us to gain a deep understanding of the factors (using density functional theory calculations) that can affect magnetic ordering of such low-dimensional magnetic units. We discovered that the magnetic properties of phases containing these magnetic subunits can be drastically tuned by chemical substitution within the metallic nonmagnetic network. For example, the small hysteresis (measure of magnetic energy storage) of Ti2FeRh5B2 can be successively increased up to 24-times by gradually substituting Ru for Rh, a result that was

  18. Removal of Vanadium from Molten Aluminum—Part III. Analysis of Industrial Boron Treatment Practice

    Science.gov (United States)

    Khaliq, Abdul; Akbar Rhamdhani, Muhammad; Brooks, Geoffrey A.; Grandfield, John

    2014-04-01

    Transition metal impurities (V, Ti, Zr, and Cr) reduce the electrical conductivity of smelter grade aluminum. These impurities are removed in the form of their borides by reacting with added Al-B master alloys i.e., boron treatment. Although, boron treatment is widely used for the production of high purity aluminum alloys in casthouse the fundamental understanding is lacking and published industrial data are limited. In the current study, industrial trials on the removal of impurities were conducted at one of the high purity aluminum alloys producers in Australasia. Kinetics analysis revealed that the rate of reaction is controlled by the mass transfer of impurities in the bulk melt. The measured mass transfer coefficient ( k m) of V and Ti were 1.1 × 10-4 and 2.6 × 10-4 m/s respectively, in the naturally stirred molten aluminum. The rate of V and Ti removal was faster compared to Zr and Cr during the boron treatment of smelter grade aluminum. Mass balance analysis revealed that 70 wt pct of V and Ti combined as borides in the first hour of the total 12 hours of boron treatment process. The calculated amount of un-reacted B was approximately 25.5 wt pct of initial amount added that remained in the final alloy. There was no evidence of boride rings formation, although partially dissolved AlB12 particles were observed under scanning electron microscope. Finally, implications for industrial practice are discussed for the improvement of current boron treatment process that include changing the source of boron, multiple stage addition of boron and better stirring of the molten aluminum.

  19. Liquid Phase Sintering of Boron-Containing Powder Metallurgy Steel with Chromium and Carbon

    Science.gov (United States)

    Wu, Ming-Wei; Fan, Yu-Chi; Huang, Her-Yueh; Cai, Wen-Zhang

    2015-11-01

    Liquid phase sintering is an effective method to improve the densification of powder metallurgy materials. Boron is an excellent alloying element for liquid phase sintering of Fe-based materials. However, the roles of chromium and carbon, and particularly that of the former, on liquid phase sintering are still undetermined. This study demonstrated the effects of chromium and carbon on the microstructure, elemental distribution, boride structure, liquid formation, and densification of Fe-B-Cr and Fe-B-Cr-C steels during liquid phase sintering. The results showed that steels with 0.5 wt pct C densify faster than those without 0.5 wt pct C. Moreover, although only one liquid phase forms in Fe-B-Cr steel, adding 0.5 wt pct C reduces the formation temperature of the liquid phase by about 50 K (°C) and facilitates the formation of an additional liquid, resulting in better densification at 1473 K (1200 °C). In both Fe-B-Cr and Fe-B-Cr-C steels, increasing the chromium content from 1.5 to 3 wt pct raises the temperature of liquid formation by about 10 K (°C). Thermodynamic simulations and experimental results demonstrated that carbon atoms dissolved in austenite facilitate the eutectic reaction and reduce the formation temperature of the liquid phase. In contrast, both chromium and molybdenum atoms dissolved in austenite delay the eutectic reaction. Furthermore, the 3Cr-0.5Mo additive in the Fe-0.4B steel does not change the typical boride structure of M2B. With the addition of 0.5 wt pct C, the crystal structure is completely transformed from M2B boride to M3(B,C) boro-carbide.

  20. Identification of novel sulfur-containing steroids in sediments and petroleum: probable incorporation of sulfur into δ 5,7-sterols during early diagenesis

    Science.gov (United States)

    Sinninghe Damsté, Jaap S.; Schouten, Stefan; de Leeuw, Jan W.; van Duin, Adri C. T.; Geenevasen, Jan A. J.

    1999-01-01

    A novel sulfur-containing sterane, 4α,7α-epithio-5β-cholestane, has been identified in a sediment extract from the Miocene Northern Apennines marl (Italy) after its isolation by column chromatography and high pressure liquid chromatography. The compound has been characterised by GC-MS and mild Nickel boride desulfurisation and one and two-dimensional 1H NMR techniques. C 27-C 29 homologs have been detected in sediment extracts of three different formations and in one petroleum sample. These sulfur-containing steroids are probably formed by an intramolecular reaction of inorganic sulfides with early diagenetic products of Δ 5,7-sterols.

  1. Material comprising two different non-metallic parrticles having different particle sizes for use in solar reactor

    Science.gov (United States)

    Klausner, James F.; Momen, Ayyoub Mehdizadeh; Al-Raqom, Fotouh A.

    2017-10-03

    Disclosed herein is a composite particle comprising a first non-metallic particle in which is dispersed a second non-metallic particle, where the first non-metallic particle and the second non-metallic particle are inorganic; and where a chemical composition of the first non-metallic particle is different from a chemical composition of the second non-metallic particle; and where the first non-metallic particle and the second non-metallic particle are metal oxides, metal carbides, metal nitrides, metal borides, metal silicides, metal oxycarbides, metal oxynitrides, metal boronitrides, metal carbonitrides, metal borocarbides, or a combination thereof.

  2. High temperature solar energy absorbing surfaces

    Science.gov (United States)

    Schreyer, J.M.; Schmitt, C.R.; Abbatiello, L.A.

    A solar collector having an improved coating is provided. The coating is a plasma-sprayed coating comprising a material having a melting point above 500/sup 0/C at which it is stable and selected from the group of boron carbide, boron nitride, metals and metal oxides, nitrides, carbides, borides, and silicates. The coatings preferably have a porosity of about 15 to 25% and a thickness of less than 200 micrometers. The coatings can be provided by plasma-spraying particles having a mean diameter of about 10 to 200 micrometers.

  3. Anti-scratch AlMgB14 Gorilla® Glass coating

    Science.gov (United States)

    Putrolaynen, V. V.; Grishin, A. M.; Rigoev, I. V.

    2017-10-01

    Hard aluminum-magnesium boride (BAM) films were fabricated onto Corning® Gorilla® Glass by radio-frequency magnetron sputtering of a single stoichiometric AlMgB14 target. BAM films exhibit a Vickers hardness from 10 to 30 GPa and a Young's modulus from 80 to 160 GPa depending on applied loading forces. Deposited hard coating increases the critical load at which glass substrate cracks. The adhesion energy of BAM films on Gorilla® Glass is 6.4 J/m2.

  4. Foreword

    Science.gov (United States)

    Manghnani, Murli H.

    2015-09-01

    The 18th International Symposium on Boron, Borides and Related Materials was held in Hawaii Prince Hotel Waikiki, Honolulu, Hawaii, USA on August 31 to September 5, 2014 (ISBB 2014). A booklet of the Program and Abstracts prepared for the Symposium served as an important record of the scientific papers presented as oral paper (68) and as posters (53). The wide range of contributions in various areas of inter-disciplinary research in boron-related materials, and the discussions during the sessions, demonstrated impressive advancements and offer many future opportunities for individual as well as collaborative endeavors globally.

  5. Incoherent x-ray emission of titanium diboride at the boron site

    Energy Technology Data Exchange (ETDEWEB)

    Ederer, D.L.; Winarski, R.; Ek, J. van [Tulane Univ., New Orleans, LA (United States)] [and others

    1997-04-01

    This group has made a study of a large number of transition metal diborides and hexaborides. As an example they would like to consider one of them. This class of compounds are of technical interest because they are quite hard, metallic, and chemically stable, and have high melting points. In addition to the technical importance of the borides, the group is interested in compounds of this type because of the very strong 1s {r_arrow} p* resonance that has been observed and associated with the boron atom.

  6. A Study of Soil Tillage Tools from Boronized Sintered Iron

    Science.gov (United States)

    Yazici, A.; Çavdar, U.

    2017-03-01

    Acomparative analysis of the properties of boronized sintered iron and quenched steels 30MnB5, 28MnCrB5 used for making soil tillage tools is performed. The microstructure, phase composition, hardness and strength characteristics of the materials are studied. The composition of the boride phase formed in the sintered iron after boronizing is determined by an x-ray method. The losses to abrasive wear are evaluated with the help of a device containing a special bin with a sample of abrasive soil.

  7. In-situ Formation of Reinforcement Phases in Ultra High Temperature Ceramic Composites

    Science.gov (United States)

    Stackpoole, Margaret M (Inventor); Gasch, Matthew J (Inventor); Olson, Michael W (Inventor); Hamby, Ian W. (Inventor); Johnson, Sylvia M (Inventor)

    2013-01-01

    A tough ultra-high temperature ceramic (UHTC) composite comprises grains of UHTC matrix material, such as HfB.sub.2, ZrB.sub.2 or other metal boride, carbide, nitride, etc., surrounded by a uniform distribution of acicular high aspect ratio reinforcement ceramic rods or whiskers, such as of SiC, is formed from uniformly mixing a powder of the UHTC material and a pre-ceramic polymer selected to form the desired reinforcement species, then thermally consolidating the mixture by hot pressing. The acicular reinforcement rods may make up from 5 to 30 vol % of the resulting microstructure.

  8. Ab initio investigation of Al/Mo2B interfacial adhesion

    OpenAIRE

    SI ABDELKADER, H.; Faraoun, H.I.

    2011-01-01

    First-principles calculations were performed to study the adhesion and the interfacial electronic structure of aluminum/molybdenum semi-boride (Al/Mo2B) interface. The work of adhesion (Wad) was calculated for both terminations of the Mo2B surface and it was found that Mo-terminated has larger Wad than the B-terminated one. It was shown that interfacial Al and B atoms form polar covalent bonds, while bonding of interfacial Al and Mo atoms mainly presents metallic character. Computational M...

  9. Synthesis and Characterization of Boron Nitride and Molybdenum Nitride Multi-Walled Nanotubes Using Liquid Plasma Arc Discharge

    Science.gov (United States)

    Holliday, Roger; Falvo, Mike; Washburn, Sean; Superfine, Rich

    2001-11-01

    We will present results on synthesis of Boron Nitride and Molybdenum Nitride nanotubes using the liquid nitrogen plasma-arc discharge method previously reported for carbon nanotubes synthesis[1]. We created a 60-100A/20-40V arc across electrodes of Hafnium Boride and Molybdenum Sulfide in a liquid nitrogen atmosphere. Nanotube geometry, nano-structure and composition characterization using TEM and EDAX will be presented. Progress in electronic and mechanical characterization as well as our incorporation of these nanotubes in to novel NEMS devices will be discussed. [1] M. Ishigami, J. Cummings, A. Zettl, S. Chen. Chemical Physical Letters 319 (2000) 457-459.

  10. Boron Nitride nanotube synthesis using liquid arc discharge

    Science.gov (United States)

    Holliday, Roger; Falvo, Mike; Washburn, Sean; Superfine, Richard

    2002-03-01

    We will present results on synthesis of Boron Nitride nanotubes using the liquid nitrogen plasma-arc discharge method previously reported for carbon nanotubes synthesis[1]. We created a 60-100A/20-40V arc across electrodes of Hafnium Boride and Molybdenum Sulfide in a liquid nitrogen atmosphere. Nanotube geometry, nano-structure and composition characterization using TEM and EDAX will be presented. Progress in electronic and mechanical characterization as well as our incorporation of these nanotubes in to novel NEMS devices will be discussed. [1] M. Ishigami, J. C., A. Zettl, S. Chen . Chemical Physical Letters 319 (2000),pp.457-459.

  11. Molten Boron Phase-Change Thermal Energy Storage: Containment and Applicability to Microsatellites (Draft)

    Science.gov (United States)

    2011-06-01

    likely since molybdenum borides become unstable below the desired experimental temperatures.42 Sample contamination through the reaction of molten...3643 0.134 0.0804 0.284 Rhenium 3453 0.15 0.09 0.325 Boron Nitride 3273 1.99 1.194 --- BeO 3010 2.43 1.458 3.41 Molybdenum 2890 0.255 0.153 0.391...Ruthenium 2607 381 117 Iridium 2739 213 147 Niobium 2750 323 53.7 Molybdenum 2896 390 138 American Institute of Aeronautics and Astronautics

  12. Prediction on technetium triboride from first-principles calculations

    Science.gov (United States)

    Miao, Xiaojia; Xing, Wandong; Meng, Fanyan; Yu, Rong

    2017-02-01

    Taking the Tc-B binary system as an example, here we report the first-principles prediction on new phases of technetium borides, TcB3, which has an unprecedented stoichiometry. Crystal structures, phase stability, electronic properties and mechanical properties of TcB3 have been investigated using first-principles calculations. The hexagonal P 6 bar m 2 structure (No.187) TcB3 with a high value of hardness (29 GPa) is energetically stable against decomposition into other compounds under pressures above 4 GPa, indicating that TcB3 can be synthesized above this pressure.

  13. An Exploration of Several Structural Measurement Techniques for Usage with Functionally Graded Materials

    Science.gov (United States)

    2006-12-01

    regarding free and forced vibrations by Yang and Shen found that at elevated temperatures, when considering FGMs in relation to an isotropic substance, FGMs ... FGM …………………………………………………… 30 12. ’Strong’ functionally graded beam after testing…………………………... 31 13. Strain gauge data for specimens F05 and F10...Member) date ii AFIT/GAE/ENY/07-D03 Abstract Titanium / titanium boride functionally graded 6”x1”x1” beams were subjected to a four

  14. Modeling the mechanical behavior of ceramic and heterophase structures manufactured using selective laser sintering and spark plasma sintering

    Science.gov (United States)

    Skripnyak, Vladimir A.; Skripnyak, Evgeniya G.; Skripnyak, Vladimir V.; Vaganova, Irina K.

    A model for predicting mechanical properties of ultra-high temperature ceramics and composites manufactured by selective laser sintering (SLS) and spark plasma sintering (SPS) under shock loading is presented. The model takes into account the porous structure, the specific volume and average sizes of phases, and the temperature of sintering. Residual stresses in ceramic composites reinforced with particles of refractory borides, carbides and nitrides after SLS or SPS were calculated. It is shown that the spall strength of diboride-zirconium matrix composites can be increased by the decreasing of porosity and the introduction of inclusions of specially selected refractory strengthening phases.

  15. LLE Review 120 (July-September 2009)

    Energy Technology Data Exchange (ETDEWEB)

    Edgell, D.H., editor

    2001-02-19

    This issue has the following articles: (1) The Omega Laser Facility Users Group Workshop; (2) The Effect of Condensates and Inner Coatings on the Performance of Vacuum Hohlraum Targets; (3) Zirconia-Coated-Carbonyl-Iron-Particle-Based Magnetorheological Fluid for Polishing Optical Glasses and Ceramics; (4) All-Fiber Optical Magnetic Field Sensor Based on Faraday Rotation in Highly Terbium Doped Fiber; (5) Femtosecond Optical Pump-Probe Characterization of High-Pressure-Grown Al{sub 0.86}Ga{sub 0.14}N Single Crystals; (6) LLE's Summer High School Research Program; (7) Laser Facility Report; and (8) National Laser Users Facility and External Users Programs.

  16. Luminescent trimethoprim-polyaminocarboxylate lanthanide complex conjugates for selective protein labeling and time-resolved bioassays

    Science.gov (United States)

    Reddy, D. Rajasekhar; Pedró Rosa, Laura E.; Miller, Lawrence W.

    2011-01-01

    Labeling proteins with long-lifetime emitting lanthanide (III) chelate reporters enables sensitive, time-resolved luminescence bioaffinity assays. Heterodimers of trimethoprim (TMP) covalently linked to various cs124-sensitized, polyaminocarboxylate chelates stably retain lanthanide ions and exhibit quantum yields of europium emission up to 20% in water. A time-resolved, luminescence resonance energy transfer (LRET) assay showed that TMP-polyaminocarboxylates bind to Escherichia coli dihydrofolate reductase (eDHFR) fusion proteins with nanomolar affinity in purified solutions and in bacterial lysates. The ability to selectively impart terbium or europium luminescence to fusion proteins in complex physiological mixtures bypasses the need for specific antibodies and simplifies sample preparation. PMID:21619068

  17. Micro-meter size organogelator with tri-color luminescence (blue, green and red) activated by Dy3+, Tb3+ and Eu3+ ions.

    Science.gov (United States)

    Wang, QianMing

    2009-09-01

    The preparation of a novel type of low-molecular-weight amphiphilic organogelator bearing three long 14-alkyl chains and hydrophilic oligo(oxyethylene) groups was described. Ultra-violet absorption and fluorescence spectra give evidence of the energy transfer between organic ligands to lanthanide ions. Characteristic green, blue and red luminescence of the organogels were obtained and interesting emission properties of terbium, dysprosium and europium ions were unexpectedly observed at the first time during the order-disorder phase transition point (29 degrees C).

  18. Giant onsite electronic entropy enhances the performance of ceria for water splitting

    DEFF Research Database (Denmark)

    Naghavi, S. Shahab; Emery, Antoine A.; Hansen, Heine Anton

    2017-01-01

    lanthanides, and reaches a maximum value of ≈4.7 kB per oxygen vacancy for Ce4+/Ce3+ reduction. This unique and large positive entropy source in ceria explains its excellent performance for high-temperature catalytic redox reactions such as water splitting. Our calculations also show that terbium dioxide has......Previous studies have shown that a large solid-state entropy of reduction increases the thermodynamic efficiency of metal oxides, such as ceria, for two-step thermochemical water splitting cycles. In this context, the configurational entropy arising from oxygen off-stoichiometry in the oxide, has...

  19. Surface-Modified Gold Nanoparticles Possessing Two-Channel Responsive Eu(III) /Tb(III) Cyclen Complexes as Luminescent Logic Gate Mimics.

    Science.gov (United States)

    Truman, Laura K; Bradberry, Samuel J; Comby, Steve; Kotova, Oxana; Gunnlaugsson, Thorfinnur

    2017-07-05

    The development of material-supported molecular logic gate mimics (MGLMs) for contained application and device fabrication has become of increasing interest. Herein, we present the formation of ≈5 nm gold nanoparticles (AuNPs) that have been surface-modified (via a thiol linkage) with heptadentate cyclen-based complexes of europium and terbium for sensing applications using delayed lanthanide luminescence and as integrated logic gate mimics within competitive media. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Synthesis and characterization of multifunctional silica core-shell nanocomposites with magnetic and fluorescent functionalities

    Energy Technology Data Exchange (ETDEWEB)

    Ma Zhiya; Dosev, Dosi [Department of Mechanical and Aeronautical Engineering, University of California-Davis, One Shields Avenue, Davis CA 95616 (United States); Nichkova, Mikaela [Department of Entomology, University of California-Davis, One Shields Avenue, Davis CA 95616 (United States); Dumas, Randy K. [Department of Physics, University of California-Davis, One Shields Avenue, Davis CA 95616 (United States); Gee, Shirley J.; Hammock, Bruce D. [Department of Entomology, University of California-Davis, One Shields Avenue, Davis CA 95616 (United States); Liu Kai [Department of Physics, University of California-Davis, One Shields Avenue, Davis CA 95616 (United States); Kennedy, Ian M. [Department of Mechanical and Aeronautical Engineering, University of California-Davis, One Shields Avenue, Davis CA 95616 (United States)], E-mail: imkennedy@ucdavis.edu

    2009-05-15

    Multifunctional core-shell nanocomposites with a magnetic core and a silica shell doped with lanthanide chelate have been prepared by a simple method. First, citric acid-modified magnetite nanoparticles were synthesized by a chemical coprecipitation method. Then the magnetite nanoparticles were coated with silica shells doped with terbium (Tb{sup 3+}) complex by a modified Stoeber method based on hydrolyzing and condensation of tetraethyl orthosilicate (TEOS) and a silane precursor. These multifunctional nanocomposites are potentially useful in a variety of biological areas such as bio-imaging, bio-labeling and bioassays because they can be simultaneously manipulated with an external magnetic field and exhibit unique phosphorescence properties.

  1. Luminescent probing of the simplest chiral α-amino acid-alanine in an enantiopure and racemic state.

    Science.gov (United States)

    Tarasevych, Arkadii V; Kostyukov, Anton I; Baronskiy, Mark G; Rastorguev, Alexander A; Guillemin, Jean-Claude; Snytnikov, Valeriy N

    2017-07-01

    Luminescent spectroscopy combined with the technique of luminescent probing with rare earth ions (europium, gadolinium, terbium) and an actinide ion (uranyl) was used to differentiate enantiopure and racemic alanine, the simplest chiral proteinogenic amino acid. Using the achiral luminescent probes, small differences between pure L and DL alanine in the solid state were strongly amplified. Based on the observed electronic transitions of the probes, the position of the triplet level of the coordinated alanine was estimated. Formation of homo- and heterochiral complexes between enantiomers of alanine and the metal ions is discussed as a possible mechanism of chiral self-discrimination. © 2017 Wiley Periodicals, Inc.

  2. Investigation of magnon dispersion relations and neutron scattering cross sections with special attention to anisotropy effects

    DEFF Research Database (Denmark)

    Lindgård, Per-Anker; Kowalska, A.; Laut, Peter

    1967-01-01

    -helical structure. A numerical calculation is performed for terbium on the basis of the Kaplan-Lyons Hamiltonian with added crystalline anisotropy. The non-istropic exchange part is shown to have a small effect on the dispersion curves, and it turns out that radical changes of the Ruderman-Kittel-type functions...... for the exchange interaction seem to be necessary for agreement with experimental dispersion curves be obtained. The effect of the anisotropy in the cross section is estimated and shown to be important for small magnon energies....

  3. Rare (Earth Elements [score

    Directory of Open Access Journals (Sweden)

    Camilo Méndez

    2014-12-01

    Full Text Available Rare (Earth Elements is a cycle of works for solo piano. The cycle was inspired by James Dillon’s Book of Elements (Vol. I-V. The complete cycle will consist of 14 pieces; one for each selected rare (earth element. The chosen elements are Neodymium, Erbium, Tellurium, Hafnium, Tantalum, Technetium, Indium, Dysprosium, Lanthanium, Cerium, Europium, Terbium, Yttrium and Darmstadtium. These elements were selected due to their special atomic properties that in many cases make them extremely valuable for the development of new technologies, and also because of their scarcity. To date, only 4 works have been completed Yttrium, Technetium, Indium and Tellurium.

  4. Alaska's rare earth deposits and resource potential

    Science.gov (United States)

    Barker, James C.; Van Gosen, Bradley S.

    2012-01-01

    Alaska’s known mineral endowment includes some of the largest and highest grade deposits of various metals, including gold, copper and zinc. Recently, Alaska has also been active in the worldwide search for sources of rare earth elements (REE) to replace exports now being limitedby China. Driven by limited supply of the rare earths, combined with their increasing use in new ‘green’ energy, lighting, transportation, and many other technological applications, the rare earth metals neodymium, europium and, in particular, the heavy rare earth elements terbium, dysprosium and yttrium are forecast to soon be in critical short supply (U.S. Department of Energy, 2010).

  5. Sol-Gel Electrolytes Incorporated by Lanthanide Luminescent Materials and Their Photophysical Properties

    Science.gov (United States)

    Yu, Chufang; Zhang, Zhengyang; Fu, Meizhen; Gao, Jinwei; Zheng, Yuhui

    2017-10-01

    A group of silica gel electrolytes with lanthanide luminescent hybrid materials were assembled and investigated. Photophysical studies showed that terbium and europium hybrids displayed characteristic green and red emissions within the electrolytes. The influence of different concentration of the lanthanide hybrids on the electrochemical behavior of a gelled electrolyte valve-regulated lead-acid battery were studied through cyclic voltammograms, electrochemical impedance spectroscopy, water holding experiments and mobility tests. The morphology and particle size were analyzed by scanning electron microscopy. The results proved that lanthanide (Tb3+/Eu3+) luminescent materials are effective additives which will significantly improve the electrochemical properties of lead-acid batteries.

  6. SPECTROSCOPIC PROPERTIES OF THE Ln-Ge COMPLEXES WITH DIETHYLENETRIAMINEPENTAACETIC ACID

    Directory of Open Access Journals (Sweden)

    Sergiy Smola

    2007-06-01

    Full Text Available Four new heteronuclear lanthanide complexes with general formula [Ge(OH(μ-HDTPALnGe(OH (μ-DTPA] (Ln = Sm – Dy were synthesized and subsequently characterized by different physico- chemical methods. The structures of new compounds have been proposed. In considered complexes the 4f-luminescence of three-charged ions of samarium, europium, terbium and dysprosium is realized at UV-excitation. It is noteworthy that it is the first observation of 4f-luminescence in water solutions of heteronuclear f-p-complexes. The comparison of luminescent characteristics of hetero- and homonuclear landthanide complexes is described and discussed as well.

  7. Tetrakis(μ-2-phenoxypropionato-κ3O,O′:O′;κ3O:O,O′,κ4O:O′-bis[(1,10-phenanthroline-κ2N,N′(2-phenoxypropionato-κ2O,O′praseodymium(III

    Directory of Open Access Journals (Sweden)

    Jin-Bei Shen

    2011-09-01

    Full Text Available In the centrosymmetric binuclear title complex, [Pr2(C9H9O36(C12H8N22], the two PrIII ions are linked by four 2-phenoxypropionate (L groups through their bi- and tridentate bridging modes. Each PrIII ion is nine-coordinated by one 1,10-phenanthroline molecule, one bidentate carboxylate group and four bridging carboxylate groups in a distorted PrN2O7 monocapped square-antiprismatic geometry. The title compound is isotypic with its terbium- and dysprosium-containing analogues.

  8. Detection of rare earth elements in Powder River Basin sub-bituminous coal ash using laser-induced breakdown spectroscopy (LIBS)

    Energy Technology Data Exchange (ETDEWEB)

    Tran, Phuoc [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United State; Mcintyre, Dustin [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United State

    2015-10-01

    We reported our preliminary results on the use of laser-induced breakdown spectroscopy to analyze the rare earth elements contained in ash samples from Powder River Basin sub-bituminous coal (PRB-coal). We have identified many elements in the lanthanide series (cerium, europium, holmium, lanthanum, lutetium, praseodymium, promethium, samarium, terbium, ytterbium) and some elements in the actinide series (actinium, thorium, uranium, plutonium, berkelium, californium) in the ash samples. In addition, various metals were also seen to present in the ash samples

  9. Faraday rotator based on TSAG crystal with orientation.

    Science.gov (United States)

    Yasuhara, Ryo; Snetkov, Ilya; Starobor, Aleksey; Mironov, Evgeniy; Palashov, Oleg

    2016-07-11

    A Faraday isolator (FI) for high-power lasers with kilowatt-level average power and 1-µm wavelength was demonstrated using a terbium scandium aluminum garnet (TSAG) with its crystal axis aligned in the direction. Furthermore, no compensation scheme for thermally induced depolarization in a magnetic field was used. An isolation ratio of 35.4 dB (depolarization ratio γ of 2.9 × 10-4) was experimentally observed at a maximum laser power of 1470 W. This result for room-temperature FIs is the best reported, and provides a simple, practical solution for achieving optical isolation in high-power laser systems.

  10. Boronization and Carburization of Superplastic Stainless Steel and Titanium-Based Alloys

    Directory of Open Access Journals (Sweden)

    Masafumi Matsushita

    2011-07-01

    Full Text Available Bronization and carburization of fine-grain superplastic stainless steel is reviewed, and new experimental results for fine grain Ti88.5Al4.5V3Fe2Mo2 are reported. In superplastic duplex stainless steel, the diffusion of carbon and boron is faster than in non-superplastic duplex stainless steel. Further, diffusion is activated by uniaxial compressive stress. Moreover, non-superplastic duplex stainless steel shows typical grain boundary diffusion; however, inner grain diffusion is confirmed in superplastic stainless steel. The presence of Fe and Cr carbides or borides is confirmed by X-ray diffraction, which indicates that the diffused carbon and boron react with the Fe and Cr in superplastic stainless steel. The Vickers hardness of the carburized and boronized layers is similar to that achieved with other surface treatments such as electro-deposition. Diffusion of boron into the superplastic Ti88.5Al4.5V3Fe2Mo2 alloy was investigated. The hardness of the surface exposed to boron powder can be increased by annealing above the superplastic temperature. However, the Vickers hardness is lower than that of Ti boride.

  11. Scoping corrosion tests on candidate waste package basket materials for the Yucca Mountain Project

    Energy Technology Data Exchange (ETDEWEB)

    Van Konynenburg, R.A.; Curits, P.C.; Summers, T.S.E.

    1998-03-01

    A scoping corrosion test was performed on candidate waste package basket materials. The corrosion medium was a pH-buffered solution of chemical species expected to be produced by radiolysis. The test was conducted at 90{degrees}C for 96 hours. Samples included aluminum-, copper-, stainless steel-, and zirconium-based metallic materials and several ceramics, incorporating neutron-absorbing elements. Sample weight losses and solution chemical changes were measured. Both corrosion of the host materials and dissolution of the neutron- absorbing elements were studied. The ceramics and the zirconium-based materials underwent only minor corrosion. the stainless steel-based materials performed well except for a welded sample. The aluminum- and copper-based materials exhibited the highest corrosion rates. Boron dissolution depends on it chemical form. Boron oxide and many metal borides dissolve readily in acidic solutions while high- chromium borides and boron carbide, though thermodynamically unstable, exhibit little dissolution in short times. the results of solution chemical analyses were consistent with this. Gadolinium did not dissolve significantly from monazite, and hafnium showed little dissolution from a variety of host materials, in keeping with its low solubility.

  12. Thermoelectric Properties and Band Structure Calculations of Novel Boron Network Compounds

    Science.gov (United States)

    Mori, Takao; Nishimura, Toshiyuki; Grin, Yuri; Shishido, Toetsu; Nakajima, Kazuo

    2009-03-01

    Boron is an interesting element, tending to form atomic networks such as 2D atomic nets and clusters, with some analogy to carbon systems which have been more extensively studied. Boron has one less electron than carbon and thus is electron deficient when forming atomic networks, but this causes it to have a special affinity with the rare earth elements and as a result, many new compounds have recently been discovered [1]. Their potential as viable thermoelectric materials is attracting interest since they are high-temperature materials and possess intrinsic low thermal conductivity, with some compounds exhibiting Seebeck coefficients in excess of 200 μV/K above 1000 K. The thermoelectric properties and band structure calculations of novel borides such as RB44Si2, RB17CN, RB22C2N, RB28.5C4 will be presented. Features in the band structure near the Fermi level indicate large doping effects in these compounds. Various doping experiments were carried out resulting in large increases to the figure of merit. [1] T. Mori, ``Higher Borides,'' in: Handbook on the Physics and Chemistry of Rare Earths, Vol. 38, (North-Holland, Amsterdam, 2008) p. 105-173.

  13. Microstructural Evolution of (Ti,W,CrB2 Coatings Deposited on Steel Substrates during Annealing

    Directory of Open Access Journals (Sweden)

    Aleksandra Newirkowez

    2014-05-01

    Full Text Available The topic of the present experiments are transition metal diboride coatings of composition (Ti0.49W0.51B2 and (Ti0.44W0.30Cr0.26B2. The coatings were deposited on steel substrates using dc magnetron sputtering. We investigated how annealing in argon at elevated temperatures modifies microstructure. The as-deposited films are amorphous. Annealing between 700 and 1100 °C results in the formation of nano-crystalline precipitates with average grain diameters of about 10–50 nm. A TiC phase (Fm-3m; a ≈ 4.3 Å is observed as the dominating precipitate phase. In addition, small amounts (10%–20% of a Cr23C6 phase (Fm-3m; a ≈ 10.6 Å are observed. In contrast to literature data on the same coatings deposited on silicon substrates, the formation of boride precipitate phases is strongly suppressed here. From investigations with X-ray diffractometry, electron microscopy and secondary ion mass spectrometry we conclude that the nanostructure of the coatings is formed by reactive phase formation of the boride coating with the carbon containing steel substrate.

  14. Stabilization of LnB12 (Ln = Gd, Sm, Nd, and Pr) in Zr1-xLnxB12 under Ambient Pressure.

    Science.gov (United States)

    Akopov, Georgiy; Sobell, Zachary C; Yeung, Michael T; Kaner, Richard B

    2016-12-05

    We report ambient pressure stabilization of a previously synthesized high-pressure (6.5 GPa) phase, GdB12, in a Zr1-xGdxB12 solid solution (with ∼54 at. % Gd solubility, as determined by both powder X-ray diffraction and energy-dispersive spectroscopy). Limited solubilities of Sm (∼15 at. % Sm), Nd (∼7 at. % Nd), and Pr (∼4 at. % Pr), in ZrB12 were also achieved. Previous attempts at preparing these rare-earth borides were unsuccessful even under high pressure. On the basis of insights provided from the unit cell sizes observed via solid solutions, at least 6.5 GPa of pressure would be needed to synthesize these rare-earth borides since Sm, Nd, and Pr atomic radii are larger than that of Gd. The solid-solution formation for Zr1-xGdxB12 and Zr1-xSmxB12 can be seen in the change of the unit cell of each of the solid solutions relative to their pure parent compounds as well as in the change of color of the respective alloys. For Zr0.45Gd0.55B12 and Zr0.70Sm0.30B12, the cubic unit cell parameter (a) reached a value of 7.453 and 7.428 Å, respectively, compared to 7.412 Å for pure ZrB12.

  15. Microstructural analyses of B{sub 4}C-CeO{sub 2} and B{sub 4}C-La{sub 2}O{sub 3} ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Sakamoto, Tatsuaki, E-mail: sakamoto.tatsuaki@eng.ehime-u.ac.jp [Department of Materials Science and Biotechnology, Ehime University, 3 Bunkyo-cho, Matsuyama 790-8577 (Japan); Sun, Shu-Chen [School of Materials and Metallurgy, Northeastern University, Shenyang 110004 (China); Furuno, Tomoya; Kajioka, Michio [Graduate Student of Ehime Univerisity, 3 Bunkyo-cho, Matsuyama 790-8577 (Japan); Nakai, Kiyomichi [Department of Materials Science and Biotechnology, Ehime University, 3 Bunkyo-cho, Matsuyama 790-8577 (Japan); Kurishita, Hiroaki [International Research Center for Nuclear Materials Science, Institute for Materials Research, Tohoku University, Oarai, Ibaraki 311-1313 (Japan); Kobayashi, Sengo [Department of Materials Science and Biotechnology, Ehime University, 3 Bunkyo-cho, Matsuyama 790-8577 (Japan); Wu, Wen-Yuan; Tu, Gan-Feng [School of Materials and Metallurgy, Northeastern University, Shenyang 110004 (China); Matsuda, Seiji [Department of Anatomy and Embryology, Ehime University, Shizugawa, Toon 791-0295 (Japan)

    2011-10-01

    Effects of additions of CeO{sub 2} and La{sub 2}O{sub 3} on microstructure and mechanical properties of B{sub 4}C fabricated under and without hot press have been investigated. Vickers hardness and fracture strength are increased by hot press due to the reduction of porosity because the sintering rate is enhanced. Hardness is increased by the reduction of porosity because crack probably occurs when the hardness is measured due to pore as an initiation point of crack. Hardness increases with increasing additions of CeO{sub 2} and La{sub 2}O{sub 3} because porosity decreases due to the formation of CeB{sub 6} and LaB{sub 6} on the grain boundary of B{sub 4}C, respectively. The borides are formed through reaction between solid phases, which might induce coherent boundary between boride and B{sub 4}C. Such coherency also contributes to strengthening the grain boundary of B{sub 4}C. The addition of CeO{sub 2} enhances the sintering rate more than that of La{sub 2}O{sub 3}, resulting in higher hardness of B{sub 4}C-CeO{sub 2} than that of B{sub 4}C-La{sub 2}O{sub 3}.

  16. High temperature thermoelectric energy conversion

    Science.gov (United States)

    Wood, Charles

    1987-01-01

    The theory and current status of materials research for high-temperature thermoelectric energy conversion are reviewed. Semiconductors are shown to be the preferred class of materials for this application. Optimization of the figure of merit of both broadband and narrow-band semiconductors is discussed as a function of temperature. Phonon scattering mechanisms are discussed, and basic material guidelines are given for reduction of thermal conductivity. Two general classes of materials show promise for high temperature figure of merit (Z) values, namely the rare earth chalcogenides and the boron-rich borides. The electronic transport properties of the rare earth chalcogenides are explicable on the basis of degenerate or partially degenerate n-type semiconductors. Boron and boron-rich borides exhibit p-type hopping conductivity, with detailed explanations proposed for the transport differing from compound to compound. Some discussion is presented on the reasons for the low thermal conductivities in these materials. Also, ZTs greater than one appear to have been realized at high temperature in many of these compounds.

  17. Effect of post-boronizing heat treatment on wear behaviour and pit formation in AISI-8620 gear steel

    Energy Technology Data Exchange (ETDEWEB)

    Aydin, H.; Sevim, V.; Demirci, A.H. [Uludag Univ., Gorukle-Bursa (Turkey)

    2007-07-01

    In this study the effect of post-boronizing heat treatment on wear behaviour and pit formation on a starter motor pinion gear, made from AISI-8620 steel, was investigated. This involved using a rotary wear test, where the number of cycles at a fixed load and a fixed rotational speed were varied. Boronizing was performed on starter motor pinion gears (test specimens) in a solid medium consisting of B{sub 4}C, SiC, KBF{sub 4} at a temperature of 900 C for 4 h. Following boronizing, test specimens were quenched in water at room temperature from the boronizing temperature and were subsequently tempered at 180 C for 1, 2 and 3 hours. As part of this investigation, microstructure and microhardness distribution of the boride layer and wear resistance and pitting damage rate of the specimens were examined for each of the tempering heat treatments. Morphology of the boride layer and pit formation were characterized using optical microscopy. Wear and pitting evaluations were carried out using a wear test apparatus made for this purpose, which simulates the pinion and flywheel starter ring gear pair. For each wear test the number of cycles was 25 x 10{sup 5}, inspected at 5 x 10{sup 5}-cycle intervals. It was concluded from these examinations that tempering heat treatments following boronizing contribute to the increase of microhardness alongside the surface layer, as well as an increase in wear resistance and pitting damage. (orig.)

  18. Microwave method for synthesis of micro- and nanostructures with controllable composition during gyrotron discharge

    Science.gov (United States)

    Batanov, German M.; Borzosekov, Valentin D.; Golberg, Dmitri; Iskhakova, Ludmila D.; Kolik, Leonid V.; Konchekov, Evgeny M.; Kharchev, Nikolai K.; Letunov, Alexander A.; Malakhov, Dmitry V.; Milovich, Filipp O.; Obraztsova, Ekaterina A.; Petrov, Alexander E.; Ryabikina, Irina G.; Sarksian, Karen A.; Stepakhin, Vladimir D.; Skvortsova, Nina N.

    2016-01-01

    We introduce an approach toward the synthesis of micro- and nanostructures under nonequilibrium microwave discharges within metal-dielectric powder mixtures induced by powerful microwave gyrotron radiation. A new plasma-chemical reactor capable of sustaining a discharge regime with an afterglow phase of an order of magnitude longer than the gyrotron pulse duration was constructed for these experiments. In the nonequilibrium conditions of such a discharge, plasma-induced exothermic chemical reactions leading to the synthesis of various compounds were initiated. The synthesized structures were deposited on the reactor walls and on the impurity particles within the reactor. This method was tested under gyrotron-initiated discharges within various metal-dielectric powder mixtures of titanium-boron, molybdenum-boron, titanium-silicon-boron, molybdenum-boron nitride, molybdenum-tungsten-boron nitride, and so on. Depending on the powder mixture composition, reactor atmosphere, and other parameters, micro- and nanosized particles of boron nitride, titanium diboride, molybdenum boride, titanium boride, molybdenum, and molybdenum oxide, were synthesized, detected, and analyzed.

  19. Thermal and stress studies of normal incidence Mo/B4C multilayers for a 6.7 nm wavelength.

    Science.gov (United States)

    Barthelmess, Miriam; Bajt, Saša

    2011-04-10

    Wavelength, reflectance, and stress stability of Mo/B(4)C multilayers were studied as a function of postdeposition annealing up to 900 °C. These multilayers are of interest as normal incidence coatings for wavelengths above the boron K-absorption edge. Mo/B(4)C multilayers deposited at low sputtering pressure have high compressive stress. Zero stress can be achieved at 360 °C-370 °C, but annealing at molybdenum and boron carbide layers separated by amorphous layers of molybdenum borides (Mo(x)B(y)) is presented. These interlayers are present already in the as-deposited state and continue to grow with increasing temperature. Their presence lowers the optical contrast and the achievable reflectivity. However, they also increase multilayer thermal stability. At temperatures >600 °C, a noticeable decrease in reflectivity associated with the phase transition from amorphous to crystalline molybdenum boride is observed. This is accompanied with an increase in interface and surface roughness and a change in stress as a function of temperature. © 2011 Optical Society of America

  20. Thermal and stress studies of normal incidence Mo/B{sub 4}C multilayers for a 6.7 nm wavelength

    Energy Technology Data Exchange (ETDEWEB)

    Barthelmess, Miriam; Bajt, Sasa

    2011-04-10

    Wavelength, reflectance, and stress stability of Mo/B{sub 4}C multilayers were studied as a function of postdeposition annealing up to 900 deg. C. These multilayers are of interest as normal incidence coatings for wavelengths above the boron K-absorption edge. Mo/B{sub 4}C multilayers deposited at low sputtering pressure have high compressive stress. Zero stress can be achieved at 360 deg. C-370 deg. C, but annealing at <200 deg. C is sufficient to reduce stress by {approx}40%. This stress relaxation is accompanied with a multilayer period expansion of {approx}0.02 nm and a <0.5% decrease in normal incidence reflectivity. The multilayer period remains stable up to {approx}600 deg. C, while intrinsic stress changes from compressive to tensile. A four-layer model with amorphous molybdenum and boron carbide layers separated by amorphous layers of molybdenum borides (Mo{sub x}B{sub y}) is presented. These interlayers are present already in the as-deposited state and continue to grow with increasing temperature. Their presence lowers the optical contrast and the achievable reflectivity. However, they also increase multilayer thermal stability. At temperatures >600 deg. C, a noticeable decrease in reflectivity associated with the phase transition from amorphous to crystalline molybdenum boride is observed. This is accompanied with an increase in interface and surface roughness and a change in stress as a function of temperature.

  1. Boronization and Carburization of Superplastic Stainless Steel and Titanium-Based Alloys.

    Science.gov (United States)

    Matsushita, Masafumi

    2011-07-18

    Bronization and carburization of fine-grain superplastic stainless steel is reviewed, and new experimental results for fine grain Ti88.5Al4.5V₃Fe₂Mo₂ are reported. In superplastic duplex stainless steel, the diffusion of carbon and boron is faster than in non-superplastic duplex stainless steel. Further, diffusion is activated by uniaxial compressive stress. Moreover, non-superplastic duplex stainless steel shows typical grain boundary diffusion; however, inner grain diffusion is confirmed in superplastic stainless steel. The presence of Fe and Cr carbides or borides is confirmed by X-ray diffraction, which indicates that the diffused carbon and boron react with the Fe and Cr in superplastic stainless steel. The Vickers hardness of the carburized and boronized layers is similar to that achieved with other surface treatments such as electro-deposition. Diffusion of boron into the superplastic Ti88.5Al4.5V₃Fe₂Mo₂ alloy was investigated. The hardness of the surface exposed to boron powder can be increased by annealing above the superplastic temperature. However, the Vickers hardness is lower than that of Ti boride.

  2. Tribological Properties of Surface Layer with Boron in Friction Pairs

    Science.gov (United States)

    Lubas, Janusz

    The aim of the present work is to determine the influence of technologically produced boron surface layers on the friction parameters in the sliding pairs under the conditions of mixed friction. The tribological evaluation included ion nitrided, pack borided, laser borided, quenched and tempered surface layers and TiB2 coating deposited on 38CrAlMo5-10, 46Cr2 and 30MnB4 steels. Modified surface layers of annular samples were matched under test conditions with counter-sample made from AlSn20 bearing alloy. Tested sliding pairs were lubricated with 15 W/40 Lotos mineral engine oil. The tribological tests were conducted on a T-05 block on ring tester. The applied steel surface layer modification with boron allows surface layers to be created with pre-determined tribological characteristics required for the elements of kinematic pairs operating in the conditions of sliding friction. Pack boronizing reduces the friction coefficient during the start-up of the frictional pair and the maximum start-up resistance level is similar to the levels of pairs with nitrided surface layers.

  3. Detection of bacterial spores with lanthanide-macrocycle binary complexes.

    Science.gov (United States)

    Cable, Morgan L; Kirby, James P; Levine, Dana J; Manary, Micah J; Gray, Harry B; Ponce, Adrian

    2009-07-15

    The detection of bacterial spores via dipicolinate-triggered lanthanide luminescence has been improved in terms of detection limit, stability, and susceptibility to interferents by use of lanthanide-macrocycle binary complexes. Specifically, we compared the effectiveness of Sm, Eu, Tb, and Dy complexes with the macrocycle 1,4,7,10-tetraazacyclododecane-1,7-diacetate (DO2A) to the corresponding lanthanide aquo ions. The Ln(DO2A)(+) binary complexes bind dipicolinic acid (DPA), a major constituent of bacterial spores, with greater affinity and demonstrate significant improvement in bacterial spore detection. Of the four luminescent lanthanides studied, the terbium complex exhibits the greatest dipicolinate binding affinity (100-fold greater than Tb(3+) alone, and 10-fold greater than other Ln(DO2A)(+) complexes) and highest quantum yield. Moreover, the inclusion of DO2A extends the pH range over which Tb-DPA coordination is stable, reduces the interference of calcium ions nearly 5-fold, and mitigates phosphate interference 1000-fold compared to free terbium alone. In addition, detection of Bacillus atrophaeus bacterial spores was improved by the use of Tb(DO2A)(+), yielding a 3-fold increase in the signal-to-noise ratio over Tb(3+). Out of the eight cases investigated, the Tb(DO2A)(+) binary complex is best for the detection of bacterial spores.

  4. Structural Characterization and Absolute Luminescence Efficiency Evaluation of Gd2O2S High Packing Density Ceramic Screens Doped with Tb3+ and Eu3+ for further Applications in Radiology

    Science.gov (United States)

    Dezi, Anna; Monachesi, Elenasophie; D’Ignazio, Michela; Scalise, Lorenzo; Montalto, Luigi; Paone, Nicola; Rinaldi, Daniele; Mengucci, Paolo; Loudos, George; Bakas, Athanasios; Michail, Christos; Valais, Ioannis; Fountzoula, Christine; Fountos, George; David, Stratos

    2017-11-01

    Rare earth activators are impurities added in the phosphor material to enhance probability of visible photon emission during the luminescence process. The main activators employed are rare earth trivalent ions such as Ce+3, Tb+3, Pr3+ and Eu+3. In this work, four terbium-activated Gd2O2S (GOS) powder screens with different thicknesses (1049 mg/cm2, 425.41 mg/cm2, 313 mg/cm2 and 187.36 mg/cm2) and one europium-activated GOS powder screen (232.18 mg/cm2) were studied to investigate possible applications for general radiology detectors. Results presented relevant differences in crystallinity between the GOS:Tb doped screens and GOS:Eu screens in respect to the dopant agent present. The AE (Absolute efficiency) was found to rise (i) with the increase of the X-ray tube voltage with the highest peaking at 110kVp and (ii) with the decrease of the thickness among the four GOS:Tb. Comparing similar thickness values, the europium-activated powder screen showed lower AE than the corresponding terbium-activated.

  5. Synthesis and characterization of magnetic nanoparticles of oxides for dual MnFe{sub 2}O{sub 4} bioseparation, stabilized in fatty acid and the system chitosan - Eu(TTA){sub 3}(TPPO){sub 2}. Studies on the influence of doping with Gd{sup 3+}, Tb{sup 3+}, Ho{sup 3+} e Eu{sup 3+} in structural and magnetic properties; Sintese e caracterizacao de nanoparticulas magneticas de oxidos duplos de MnFe{sub 2}O{sub 4} para biosseparacao, estabilizadas em acido graxo e recobertas pelo sistema quitosana - Eu(TTA){sub 3}(TPPO){sub 2}. Estudo da influencia da dopagem com Gd{sup 3+}, Tb{sup 3+}, Ho{sup 3+} e Eu{sup 3+} nas propriedades estruturais e magneticas

    Energy Technology Data Exchange (ETDEWEB)

    Kovacs, Thelma Antunes Rodrigues

    2014-07-01

    This work was synthesized and characterized ferrite magnetic nanoparticles manganese, using the chemical coprecipitation method. By varying the heating time under 98°C (0, 10,20,40,60 3 80 minutes), the molar percentage of doping (1, 3, 5, 7, and 10%), gadolinium, europium, terbium and holmium. Magnetic ferrite nanoparticles and manganese ferrite doped with manganese were synthesized by coprecipitation method starting with chloride solutions of metals (iron (III), manganese (II), europium (III), gadolinium (III), terbium (III) and holmium (III)) and NaOH 5mol.L{sup -1} as precipitating agent. The magnetic nanoparticles were characterized by scanning electron microscopy, infrared spectroscopy, X-ray diffraction, magnetization curves, and thermal analysis. Most of manganese ferrite particles showed superparamagnetic behavior. After the characterization it was found that the samples synthesized manganese ferrite with more than 40 minutes heating time, crystal structure showed the characteristic pattern of the inverted manganese ferrite spinel type. The stabilization of the samples in oleic acid nanoparticles produced with a hydrophobic outer layer and facilitated by coating chitosan biopolymer, since this has a positive charge. Among the doped samples there was no significant change in the magnetic behavior. Several techniques for characterizing these materials have been used such as X-ray diffraction spectrum in the infrared region, magnetization curves and thermal analysis. The resins were tested as magnetic material for the separation of biological materials. In this paper, are used as biological targets separation of bovine serum albumin. (author)

  6. Cerium fluoride nanoparticles protect cells against oxidative stress

    Energy Technology Data Exchange (ETDEWEB)

    Shcherbakov, Alexander B.; Zholobak, Nadezhda M. [Zabolotny Institute of Microbiology and Virology, National Academy of Sciences of Ukraine, Kyiv D0368 (Ukraine); Baranchikov, Alexander E. [Kurnakov Institute of General and Inorganic Chemistry of the Russian Academy of Sciences, Moscow 119991 (Russian Federation); Ryabova, Anastasia V. [Prokhorov General Physics Institute of the Russian Academy of Sciences, Moscow 119991 (Russian Federation); National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), Moscow 115409 (Russian Federation); Ivanov, Vladimir K., E-mail: van@igic.ras.ru [Kurnakov Institute of General and Inorganic Chemistry of the Russian Academy of Sciences, Moscow 119991 (Russian Federation); National Research Tomsk State University, Tomsk 634050 (Russian Federation)

    2015-05-01

    A novel facile method of non-doped and fluorescent terbium-doped cerium fluoride stable aqueous sols synthesis is proposed. Intense green luminescence of CeF{sub 3}:Tb nanoparticles can be used to visualize these nanoparticles' accumulation in cells using confocal laser scanning microscopy. Cerium fluoride nanoparticles are shown for the first time to protect both organic molecules and living cells from the oxidative action of hydrogen peroxide. Both non-doped and terbium-doped CeF{sub 3} nanoparticles are shown to provide noteworthy protection to cells against the vesicular stomatitis virus. - Highlights: • Facile method of CeF{sub 3} and CeF{sub 3}:Tb stable aqueous sols synthesis is proposed. • Naked CeF{sub 3} nanoparticles are shown to be non-toxic and to protect cells from the action of H{sub 2}O{sub 2}. • CeF{sub 3} and CeF{sub 3}:Tb nanoparticles are shown to protect living cells against the vesicular stomatitis virus.

  7. Synthesis and characterization of Tin / Titanium mixed oxide nanoparticles doped with lanthanide for biomarking; Sintese e caracterizacao de nanoparticulas de oxido misto de estanho/titanio dopadas com lantanideos para marcacao biologica

    Energy Technology Data Exchange (ETDEWEB)

    Paganini, Paula Pinheiro

    2012-07-01

    This work presents the synthesis, characterization and photo luminescent study of tin and titanium mixed oxide nanoparticles doped with europium, terbium and neodymium to be used with luminescent markers on biological systems. The syntheses were done by co-precipitation, protein sol-gel and Pechini methods and the nanoparticles were characterized by infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, X-ray diffraction and X-ray absorption spectroscopy. The photo luminescent properties studies were conducted for luminophores doped with europium, terbium and neodymium synthesized by coprecipitation method. For luminophore doped with europium it was possible to calculate the intensity parameters and quantum yield and it showed satisfactory results. In the case of biological system marking it was necessary the functionalization of these particles to allow them to bind to the biological part to be studied. So the nanoparticles were functionalized by microwave and Stoeber methods and characterized by infrared spectroscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction obtaining qualitative response of functionalization efficacy. The ninhydrin spectroscopic method was used for quantification of luminophores functionalization. The photo luminescent studies of functionalized particles demonstrate the potential applying of these luminophores as luminescent markers. (author)

  8. Fabrication of Tb3Al5O12 transparent ceramics using co-precipitated nanopowders

    Science.gov (United States)

    Dai, Jiawei; Pan, Yubai; Wang, Wei; Luo, Wei; Xie, Tengfei; Kou, Huamin; Li, Jiang

    2017-11-01

    Terbium aluminum garnet (TAG) precursor was synthesized by a co-precipitation method from a mixed solution of terbium and aluminum nitrates using ammonium hydrogen carbonate (AHC) as the precipitant. The powders calcined at different temperatures were investigated by XRD, FTIR and FESEM in order to choose the optimal calcination temperature. Fine and low-agglomerated TAG powders with average particle size of 88 nm were obtained by calcining the precursor at 1100 °C for 4 h. Using this powder as starting material, TAG transparent ceramics were fabricated by vacuum sintering combined with hot isostatic pressing (HIP) sintering. For the sample pre-sintered at 1700 °C for 20 h with HIP post-treated at 1700 °C for 3 h, the average grain size is about 3.9 μm and the in-line transmittance is beyond 55% in the region of 500-1600 nm, reaching a maximum transmittance of 64.2% at the wavelength of 1450 nm. The Verdet constant at 633 nm is measured to be -178.9 rad T-1 m-1, which is 33% larger than that of the commercial TGG single crystal (-134 rad T-1 m-1).

  9. Incorporation of Ln-Doped LaPO4 Nanocrystals as Luminescent Markers in Silica Nanoparticles.

    Science.gov (United States)

    van Hest, Jacobine J H A; Blab, Gerhard A; Gerritsen, Hans C; Donega, Celso de Mello; Meijerink, Andries

    2016-12-01

    Lanthanide ions are promising for the labeling of silica nanoparticles with a specific luminescent fingerprint due to their sharp line emission at characteristic wavelengths. With the increasing use of silica nanoparticles in consumer products, it is important to label silica nanoparticles in order to trace the biodistribution, both in the environment and living organisms.In this work, we synthesized LaPO4 nanocrystals (NCs) with sizes ranging from 4 to 8 nm doped with europium or cerium and terbium. After silica growth using an inverse micelle method, monodisperse silica spheres were obtained with a single LaPO4 NC in the center. We demonstrate that the size of the silica spheres can be tuned in the 25-55 nm range by addition of small volumes of methanol during the silica growth reaction. Both the LaPO4 core and silica nanocrystal showed sharp line emission characteristic for europium and terbium providing unique optical labels in silica nanoparticles of variable sizes.

  10. Magnetic phase transitions in TbFe sub 2 Al sub 1 sub 0 , HoFe sub 2 Al sub 1 sub 0 and ErFe sub 2 Al sub 1 sub 0

    CERN Document Server

    Reehuis, M; Krimmel, A; Scheidt, E W; Stüsser, N; Loidl, A; Jeitschko, W

    2003-01-01

    The magnetic order of the orthorhombic aluminides TbFe sub 2 Al sub 1 sub 0 , HoFe sub 2 Al sub 1 sub 0 and ErFe sub 2 Al sub 1 sub 0 (space group Cmcm) has been studied by specific heat and magnetic measurements, as well as by neutron powder diffraction down to 100 mK and in external fields up to 5 T. Only the rare-earth ions carry a magnetic moment. At T = 1.5 K the terbium moments in TbFe sub 2 Al sub 1 sub 0 show a square-wave modulated magnetic order with wavevector k = (0, 0.7977, 0) and a moment direction parallel to the a-axis. At a critical field of H sub c sub 1 = 0.9 T one of ten spins is forced to flip, going into an intermediate ferrimagnetic phase that is stable up to the critical field H sub c sub 2 = 1.8 T. Above this field finally all the rest of the spins flip, resulting in a ferromagnetic order of the terbium moments. ErFe sub 2 Al sub 1 sub 0 orders antiferromagnetically below T sub N 1.77(7) K with a similar magnetic structure characterized by a wavevector k (0, approx 0.8, 0). In contras...

  11. Deuteron induced Tb-155 production, a theranostic isotope for SPECT imaging and auger therapy.

    Science.gov (United States)

    Duchemin, C; Guertin, A; Haddad, F; Michel, N; Métivier, V

    2016-12-01

    Several terbium isotopes are suited for diagnosis or therapy in nuclear medicine. Tb-155 is of interest for SPECT imaging and/or Auger therapy. High radionuclide purity is mandatory for many applications in medicine. The quantification of the activity of the produced contaminants is therefore as important as that of the radionuclide of interest. The experiments performed at the ARRONAX cyclotron (Nantes, France), using the deuteron beam delivered up to 34MeV, provide an additional measurement of the excitation function of the Gd-nat(d,x)Tb-155 reaction and of the produced terbium and gadolinium contaminants. In this study, we investigate the achievable yield for each radionuclide produced in natural gadolinium as a function of the deuteron energy. Other reactions are discussed in order to define the production route that could provide Tb-155 with a high yield and a high radionuclide purity. This article aims to improve data for the Gd-nat(d,x) reaction and to optimize the irradiation conditions required to produce Tb-155. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Nb{sub 2}OsB{sub 2}, with a new twofold superstructure of the U{sub 3}Si{sub 2} type: Synthesis, crystal chemistry and chemical bonding

    Energy Technology Data Exchange (ETDEWEB)

    Mbarki, Mohammed; Touzani, Rachid St.; Fokwa, Boniface P.T., E-mail: boniface.fokwa@ac.rwth-aachen.de

    2013-07-15

    The new ternary metal-rich boride, Nb{sub 2}OsB{sub 2}, was synthesized by arc-melting the elements in a water-cooled copper crucible under an argon atmosphere. The compound was characterized from single-crystal X-ray data and EDX measurements. It crystallizes as a new superstructure (space group P4/mnc, no. 128) of the tetragonal U{sub 3}Si{sub 2}-structure type with lattice parameters a=5.922(1) Å and c=6.879(2) Å. All of the B atoms are involved in B{sub 2} dumbbells with B–B distances of 1.89(4) Å. Structure relaxation using VASP (Vienna ab intio Simulation Package) has confirmed the space group and the lattice parameters. According to electronic structure calculations (TB–LMTO–ASA), the homoatomic B–B interactions are optimized and very strong, but relatively strong heteroatomic Os–B, Nb–B and Nb–Os bonds are also found: These interactions, which together build a three-dimensional network, are mainly responsible for the structural stability of this new phase. The density of state at the Fermi level predicts metallic behavior, as expected, from this metal-rich boride. - Graphical abstract: Nb{sub 2}OsB{sub 2} is, to the best of our knowledge, the first fully characterized phase in the ternary Nb–Os–B system. It crystallizes (space group P4/mnc, 128) with a new twofold superstructure of the U{sub 3}Si{sub 2} structure type (space group P4/mbm, 127), and is therefore the first boride in this structure family crystallizing with a superstructure of the U{sub 3}Si{sub 2} structure type. We show that the distortions leading to this superstructure occurs mainly in the Nb-layer, which tries to accommodate the large osmium atoms. The consequence of this puckering is the building osmium dumbbells instead of chains along [001]. - Highlights: • First compound in the Nb–Os–B system. • New twofold superstructure of U{sub 3}Si{sub 2} structure type. • Puckering of Nb-layer responsible for superstructure occurrence. • Chemical bonding studied

  13. A study on laser weldability improvement of newly developed Haynes 282 superalloy

    Science.gov (United States)

    Osoba, Lawrence Opeyemi

    Haynes alloy 282 is a new gamma prime (gamma') precipitation strengthened nickel-base superalloy developed for high temperature applications in land-based and aero turbine engines. Joining is a crucial process both during the manufacturing of new components and repair of service-damaged turbine parts. Unfortunately, the new superalloy cracks during laser beam welding (LBW), which is an attractive technique for joining superalloys components due to its low heat input characteristic that preclude the geometrical distortion of welded components. This research is therefore initiated with the goal of studying and developing an effective approach for preventing or minimizing cracking during LBW of the new superalloy Haynes 282. Careful and detailed electron microscopy and spectroscopy study reveal, for the first time, the formation of sub-micron grain boundary M5B3 particles, in the material. Microstructural study of welded specimens coupled with Gleeble thermo-mechanical physical simulations shows that the primary cause of weld heat affected zone (HAZ) cracking in the alloy is the sub-solidus liquation reaction of intergranular M5B3 borides in the material. Further weldability study showed that the HAZ liquation cracking problem worsens with reduction in welding heat input, which is normally necessary to produce the desired weld geometry with minimum distortion. In order to minimize the HAZ cracking during low heat input laser welding, microstructural modification of the alloy by heat treatment at 1080--1100°C has been developed. The pre-weld heat treatment minimizes cracking in the alloy by reducing the volume fraction of the newly identified M5B3 borides, while also minimizing non-equilibrium grain boundary segregation of boron liberated during dissociation of the boride particles. Further improvement in resistance to cracking was produced by subjecting the material to thermo-mechanically induced grain refinement coupled with a pre-weld heat treatment at 1080

  14. Electrodeposition of alloys or compounds in molten salts and applications

    Directory of Open Access Journals (Sweden)

    Taxil P.

    2003-01-01

    Full Text Available This article deals with the different modes of preparation of alloys or intermetallic compounds using the electrodeposition in molten salts, more particularly molten alkali fluorides. The interest in this process is to obtain new materials for high technology, particularly the compounds of reactive components such as actinides, rare earth and refractory metals. Two ways of preparation are considered: (i electrocoating of the more reactive metal on a cathode made of the noble one and reaction between the two metals in contact, and (ii electrocoating on an inert cathode of the intermetallic compound by coreduction of the ions of each elements. The kinetic is controlled by the reaction at the electrolyte interface. A wide bibliographic survey on the preparation of various compounds (intermetallic compounds, borides, carbides… is given and a special attention is paid to the own experience of the authors in the preparation of these compounds and interpretation of their results.

  15. NASA research on refractory compounds.

    Science.gov (United States)

    Gangler, J. J.

    1971-01-01

    The behavior and properties of the refractory carbides, nitrides, and borides are being investigated by NASA as part of its research aimed at developing superior heat resistant materials for aerospace applications. Fundamental studies on the electronic and defect structures of the carbides indicate that there is promise for improving the strength and ductility of these materials. Studies of the zirconium-carbon-oxygen system show that zirconium oxycarbides of different compositions and lattice parameters can be formed between 1500 and 1900 C and are stable below 1500 C. More applied studies show that hot working generally improves the microstructure and therefore the strength of TiC and NbC. Sintering studies on UN indicate that very high densities can be achieved. Hot pressing of cermets of HfN and HfC produces good mechanical properties for high temperature bearing applications.

  16. Interaction Between Second-Phase Particle Dissolution and Abnormal Grain Growth in an Austenitic Stainless Steel

    Directory of Open Access Journals (Sweden)

    J.C. Dutra

    2002-09-01

    Full Text Available The continuing development of stainless steels has resulted in complex steel compositions with substantial amounts of alloying elements. The benefits of such additions invariably come attached to unavoidable disadvantages. One of the most critical item is the potential microstructural instability of the material. Alloying elements may be in a supersaturated solid solution, in which the precipitation of carbides, nitrides, borides and intermetallic phases occurs in a wide range of temperatures. In order to dissolve the mentioned precipitates, solution annealing is commonly performed. However, at the temperature range in which this treatment is carried out, the onset of abnormal grain growth can occur. The interaction between the dissolution of these second-phase particles and the occurrence of abnormal grain growth is investigated in this work. This study also shows that the thermodynamics and the kinetics of dissolution of precipitates may be used to predict whether abnormal grain growth takes place.

  17. Vapor-phase fabrication and properties of continuous-filament ceramic composites.

    Science.gov (United States)

    Besmann, T M; Sheldon, B W; Lowden, R A; Stinton, D P

    1991-09-06

    The continuous-filament ceramic composite is becoming recognized as necessary for new, high-temperature structural applications. Yet because of the susceptibility of the filaments to damage from traditional methods for the preparation of ceramics, vapor-phase infiltration has become the fabrication method of choice. The chemical vapor infiltration methods for producing these composites are now being studied in earnest, with the complexity of filament weaves and deposition chemistry being merged with standard heat and mass-transport relationships. Two of the most influential effects on the mechanical properties of these materials are the adhesion and frictional force between the fibers and the matrix, which can be controlled by a tailored interface coating. A variety of materials are available for producing these composites including carbide, nitride, boride, and oxide filaments and matrices. Silicon carbide-based materials are by far the most advanced and are already being used in aerospace applications.

  18. New method for synthesis of metal carbides, nitrides and carbonitrides

    Energy Technology Data Exchange (ETDEWEB)

    Koc, R.; Folmer, J.S.; Kodambaka, S.K. [Southern Illinois Univ., Carbondale, IL (United States)] [and others

    1997-04-01

    The purpose of this work is to develop a novel synthesis method using a carbothermic reduction reaction of carbon coated precursors for producing high purity, submicron, non-agglomerated powders of metal carbide, metal nitride and metal boride systems. The authors also want to demonstrate the advantages of the process and provide information on the applicability of the process for synthesizing related advanced ceramic powders (e.g. SiC, WC, TiN, TiB{sub 2}, Si{sub 3}N{sub 4}). During the FY96 of the project, steps are taken to investigate the reaction mechanisms and phase evolution during the formation of TiC from carbon coated titania precursors and to produce submicron TiC powders with desired stoichiometries. Depending on the carbon content in the coated titania precursor, TiC powder was produced with different stoichiometries (different amount of oxygen and free carbon).

  19. Transient liquid-phase bonding of ODS steels

    Energy Technology Data Exchange (ETDEWEB)

    Noto, H., E-mail: s25093145w@eng.hokudai.ac.jp [Materials Science and Engineering, Graduate School of Engineering, Hokkaido University, N-13, W-8, Kita-ku, Hokkaido Sapporo 060-8628 (Japan); Ukai, S.; Hayashi, S. [Materials Science and Engineering, Graduate School of Engineering, Hokkaido University, N-13, W-8, Kita-ku, Hokkaido Sapporo 060-8628 (Japan)

    2011-10-01

    The use of transient liquid-phase bonding of 9CrODS steels using Fe-3B-2Si-0.5C filler was investigated for bonding temperature of 1180 deg. C and hold times of 0.5-4.0 h. The sequential process, consisting of isothermal melting, solidification and homogenization, was confirmed for bonding the 9CrODS steel. The precipitation of chromium boride found in 19CrODS steel is avoided in 9CrODS steel due to the lower Cr content. Silicon tends to be slightly enriched inside the bonding zone. Agglomeration and coarsening of Y{sub 2}O{sub 3} particles in 9CrODS steel lead to softening inside the bonding zone formed by incipient melting of the foil bonding alloy, and in a diffusion affected zone (DAZ) adjacent to the bonding zone.

  20. Development of titanium diboride coatings deposited by PACVD

    Energy Technology Data Exchange (ETDEWEB)

    Pfohl, C.; Bulak, A.; Rie, K.-T. [Technische Univ. Braunschweig (Germany). Inst. fuer Oberflaechentechnik und Plasmatechnische Werkstoffentwicklung

    2000-09-01

    TiB{sub 2} appears to be a promising material for the wear protection in various tribological systems, e.g. the diecasting of Al. This study focuses on the development of titanium boride coatings deposited by PACVD, a deposition method which is most suitable for the coating of substrates with complex shapes. All layers analysed are very smooth and exhibit a quasi-amorphous fracture surface. XRD and TEM analysis indicate a nanocrystalline structure with grain sizes in the order of 2 nm. The diffraction patterns can well be correlated to titanium diboride. WDS reveals an over stoichiometric B/Ti ratio. The layer hardness reaches the value of 33 GPa and the critical load in scratch tests rises to 35 N. Neither 100Cr6 nor Al as a counterpart in pin-on-disk tests leads to wear of the coating. (orig.)

  1. Friction and wear of sintered Mg-B alloys; Mg-B kei shoketsu tokin no masatsu mamo tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Saito, J.; Takahashi, H.; Sekino, T.; Nishiyama, K. [Science University of Tokyo, Tokyo (Japan). Facultyof Science and Technology

    1999-01-15

    Sliding wear behavior of newly developed of magnesium base hard alloys containing magnesium borides carbon steel (SUJ2) wear studied by ring-on-block type Ogoshi wear resislance teste at sliding velocities of 3.55m/s, load of 20.6N and sliding distance of 66.6m to 600m. The new hard alloys exhibits better wear resistance and gives less than conventional magnesium alloys. The excellent wear performance of the new hard alloys are attributed to the improvement of hardness and the formation of oxides such as MgO and B{sub 2}O{sub 3}, which may act as lubricants during slides. (author)

  2. Magnetic field effects in electron systems with imperfect nesting

    Science.gov (United States)

    Sboychakov, A. O.; Rakhmanov, A. L.; Kugel, K. I.; Rozhkov, A. V.; Nori, Franco

    2017-01-01

    We analyze the effects of an applied magnetic field on the phase diagram of a weakly correlated electron system with imperfect nesting. The Hamiltonian under study describes two bands: electron and hole ones. Both bands have spherical Fermi surfaces, whose radii are slightly mismatched due to doping. These types of models are often used in the analysis of magnetic states in chromium and its alloys, superconducting iron pnictides, AA-type bilayer graphene, borides, etc. At zero magnetic field, the uniform ground state of the system turns out to be unstable against electronic phase separation. The applied magnetic field affects the phase diagram in several ways. In particular, the Zeeman term stabilizes new antiferromagnetic phases. It also significantly shifts the boundaries of inhomogeneous (phase-separated) states. At sufficiently high fields, the Landau quantization gives rise to oscillations of the order parameters and of the Néel temperature as a function of the magnetic field.

  3. Comprehensive hard materials

    CERN Document Server

    2014-01-01

    Comprehensive Hard Materials deals with the production, uses and properties of the carbides, nitrides and borides of these metals and those of titanium, as well as tools of ceramics, the superhard boron nitrides and diamond and related compounds. Articles include the technologies of powder production (including their precursor materials), milling, granulation, cold and hot compaction, sintering, hot isostatic pressing, hot-pressing, injection moulding, as well as on the coating technologies for refractory metals, hard metals and hard materials. The characterization, testing, quality assurance and applications are also covered. Comprehensive Hard Materials provides meaningful insights on materials at the leading edge of technology. It aids continued research and development of these materials and as such it is a critical information resource to academics and industry professionals facing the technological challenges of the future. Hard materials operate at the leading edge of technology, and continued res...

  4. Production of advanced materials by methods of self-propagating high-temperature synthesis

    CERN Document Server

    Tavadze, Giorgi F

    2013-01-01

    This translation from the original Russian book outlines the production of a variety of materials by methods of self-propagating high-temperature synthesis (SHS). The types of materials discussed include: hard, refractory, corrosion and wear-resistant materials, as well as other advanced and speciality materials. The authors address the issue of optimal parameters for SHS reactions occurring during processes involving a preliminary metallothermic reduction stage, and they calculate this using thermodynamic approaches. In order to confirm the effectiveness of this approach, the authors describe experiments focussing on the synthesis of elemental crysalline boron, boron carbides and nitrides. Other parts of this brief include theoretical and experimental results on single-stage production of hard alloys on the basis of titanium and zirconium borides, as well as macrokinetics of degassing and compaciton of SHS-products.This brief is suitable for academics, as well as those working in industrial manufacturing com...

  5. Applying a rigid band model to the XYB14 crystal family

    Science.gov (United States)

    Wan, Liwen F.; Beckman, Scott P.

    2011-10-01

    The compounds AlMgB14, AlLiB14 and MgMgB14 belong to the same space group, Imma, and share similar structural properties. It is predicted that the rigid band model accurately describes the electronic states of these orthorhombic borides. The position of the Fermi level within the states depends on the metal site constituency. In this work the electronic properties of each compound are studied in detail by ab initio methods. Löwdin population analysis is conducted to examine the local charge distribution, and the projected density of states is calculated. It is found that the valence band edge is strongly dominated by the "Binter" and "Bconnector" atoms. This indicates that moving the Fermi level into the valence band will result in changes to the local bonding between the icosahedra and the inter-icosahedra B atoms.

  6. Energy conversion device and method of reducing friction therein

    Science.gov (United States)

    Solovyeva, Lyudmila Mikhaylovna; Jansson, Kyle S; Elmoursi, Alaa AbdelAzim; Zhu, Dong; Milner, Robert; Daughterty, Early Eugene; Higdon, Clifton Baxter; Elagamy, Kamel Abdel-Khalik; Hicks, Aaron Michael

    2013-10-08

    A device configured for converting energy includes a first surface, a second surface configured for moving with respect to the first surface during operation of the device, and a coating disposed on at least one of the first surface and the second surface. The coating includes a first layer of a ceramic alloy represented by the general formula AlMgB.sub.14--X, wherein X is present in an amount of from 0 to 70 parts by weight based on 100 parts by weight of the ceramic alloy and is a doping agent selected from the group of Group IV elements and borides and nitrides thereof, and a second layer disposed on the first layer and including carbon in a gradient concentration. The coating has a hardness of from 10 to 20 GPa and a coefficient of friction of less than or equal to 0.12.

  7. Structure and phases in nickel-base self-fluxing alloy coating containing high chromium and boron

    Science.gov (United States)

    Otsubo, F.; Era, H.; Kishitake, K.

    2000-03-01

    The structure of a nickel-base, self-fluxing alloy coating, containing chromium and boron thermal sprayed and fused, was investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), electron probe microanalysis (EPMA), and transmission electron microscopy (TEM). A lumpy M6C carbide, a rodlike M3B2 boride of tetragonal structure, a rodlike M7C3 carbide of hexagonal structure, and a Ni-Ni3B eutectic phase formed in the coating after fusing. Metals of M6C, M3B2, and M7C3 phases are composed of chromium, molybdenum, and nickel; chromium and molybdenum; and mainly chromium, respectively. The nickel phase in the coating has the L12 type superlattice structure.

  8. The effect of post-treatment of a high-velocity oxy-fuel Ni-Cr-Mo-Si-B coating Part I: Microstructure/corrosion behavior relationships

    Science.gov (United States)

    Shrestha, S.; Hodgkiess, T.; Neville, A.

    2001-09-01

    The microstructure and aqueous corrosion characteristics of a Ni-Cr-Mo-Si-B high-velocity oxy-fuel (HVOF) coating have been assessed. It has been shown that postprocessing by vacuum fusion has a significant effect on the coating microstructure by increasing the type and concentration of hard phase particles. The principal hard phases in the as-sprayed condition and vacuum-sealed condition are chromium carbides, whereas molybdenum-containing boride phases are also present after vacuum fusion. Vacuumfusion post-treatment eliminates splat boundaries, which can act as sites, where preferential corrosion can occur and, hence, the dominant corrosion mechanisms change. In as-sprayed and vacuum-sealed coatings, localized attack at splat particle boundaries and crevice corrosion dominate, whereas in vacuum-fused coating, the principal mechanism of corrosion is “micropitting” as a result of the hard phase loss.

  9. XPS analysis of boron doped heterofullerenes

    Energy Technology Data Exchange (ETDEWEB)

    Schnyder, B.; Koetz, R. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Muhr, H.J.; Nesper, R. [ETH Zurich, Zurich (Switzerland)

    1997-06-01

    Boron heterofullerenes were generated through arc-evaporation of doped graphite rods in a helium atmosphere. According to mass spectrometric analysis only mono-substituted fullerenes like C{sub 59}B, C{sub 69}B and higher homologues together with a large fraction of higher undoped fullerenes were extracted and enriched when pyridine was used as the solvent. XPS analysis of the extracts indicated the presence of two boron species with significantly different binding energies. One peak was assigned to borid acid. The second one corresponds to boron in the fullerene cage, which is mainly C{sub 59}B, according to the mass spectrum. This boron is in a somewhat higher oxidation state than that of ordinary boron-carbon compounds. The reported synthesis and extraction procedure opens a viable route for production of macroscopic amounts of these compounds. (author) 2 figs., 1 tab., 7 refs.

  10. Superconductivity between standard types: Multiband versus single-band materials

    Energy Technology Data Exchange (ETDEWEB)

    Vagov, A.; Shanenko, A. A.; Milošević, M. V.; Axt, V. M.; Vinokur, V. M.; Aguiar, J. Albino; Peeters, F. M.

    2016-05-06

    In the nearest vicinity of the critical temperature, types I and II of conventional single-band superconductors interchange at the Ginzburg-Landau parameter κ = 1/√2. At lower temperatures this point unfolds into a narrow but finite interval of κ’s, shaping an intertype (transitional) domain in the (κ,T ) plane. In the present work, based on the extended Ginzburg-Landau formalism, we show that the same picture of the two standard types with the transitional domain in between applies also to multiband superconductors. However, the intertype domain notably widens in the presence of multiple bands and can become extremely large when the system has a significant disparity between the band parameters. It is concluded that many multiband superconductors, such as recently discovered borides and iron-based materials, can belong to the intertype regime.

  11. Refractory semiconductors for high temperature thermoelectric energy conversion

    Science.gov (United States)

    Wood, Charles

    Thermoelectric energy conversion utilizing nuclear heat sources has been employed for several decades to generate power for deep space probes. In the past, lead telluride and, more recently, silicon-germanium alloys have been the prime choices as thermoelectric materials for this application. Currently, a number of refractory semiconductors are under investigation at the Jet Propulsion Laboratory in order to produce power sources of higher conversion efficiency and, thus, lower mass per unit of power output. Included among these materials are improved Si-Ge alloys, rare earth compounds and boron-rich borides. The criteria used to select thermoelectric materials, in general, and the above materials, in particular, will be discussed. The current state of the art and the accomplishments to date in thermoelectric materials research will be reviewed.

  12. Advances in Ceramic Supports for Polymer Electrolyte Fuel Cells

    Directory of Open Access Journals (Sweden)

    Oran Lori

    2015-08-01

    Full Text Available Durability of catalyst supports is a technical barrier for both stationary and transportation applications of polymer-electrolyte-membrane fuel cells. New classes of non-carbon-based materials were developed in order to overcome the current limitations of the state-of-the-art carbon supports. Some of these materials are designed and tested to exceed the US DOE lifetime goals of 5000 or 40,000 hrs for transportation and stationary applications, respectively. In addition to their increased durability, the interactions between some new support materials and metal catalysts such as Pt result in increased catalyst activity. In this review, we will cover the latest studies conducted with ceramic supports based on carbides, oxides, nitrides, borides, and some composite materials.

  13. Mo5PB2: a new superconductor in the Cr5B3 structure type with Tc = 9.2 K

    Science.gov (United States)

    McGuire, Michael; Parker, David

    Superconductivity has been reported recently in several ternary silicide-borides adopting the tetragonal Cr5B3 structure type, including Nb5Si3-xBx, Mo5SiB2, and W5SiB2, with critical temperatures ranging from 5.8-7.8 K. Here we report superconductivity with Tc exceeding 9 K in the phosphorus-containing analogue Mo5PB2. We have synthesized polycrystalline samples of the compound, made measurements of electrical resistivity, magnetic susceptibility, and heat capacity, and performed first principles electronic structure calculations. The highest Tc values occur in slightly phosphorus rich samples, with composition near Mo5P1.1B1.9. Together with the measured properties, the calculations suggest the superconductivity in these materials may be multi-band. Research sponsored by the US Department of Energy, Office of Science, Basic Energy Sciences, Materials Sciences and Engineering Division.

  14. Laser ignition of high-energy materials containing AlB2 and AlB12 powders

    Directory of Open Access Journals (Sweden)

    Korotkikh Alexander

    2017-01-01

    Full Text Available Boron-containing substances are known to have high gravimetric and volumetric heats of oxidation in comparison with any metals that make them promising for using in high-energy materials. This work is aimed to study ignition characteristics of ammonium perchlorate and nitrate-based composite solid propellants containing aluminium borides by means of radiative heating by CO2-laser. It was found that the effect upon laser ignition (ignitability at full replacement of ASD-4 aluminum powder by aluminium diboride and dodecaboride is close. The ignition time of HEM is reduced by 2.0–2.5 times compared with ASD-4 HEM sample in the heat flux density range of 90–200 W/cm2.

  15. Microstructure Evolution during Supersolvus Heat Treatment of a Powder Metallurgy Nickel-Base Superalloy

    Science.gov (United States)

    Semiatin, S. L.; McClary, K. E.; Rollett, A. D.; Roberts, C. G.; Payton, E. J.; Zhang, F.; Gabb, T. P.

    2012-05-01

    Microstructure evolution during the supersolvus heat treatment of a powder-metallurgy, low-solvus, high-refractory (LSHR) superalloy was established. For this purpose, three lots of LSHR with varying initial carbon/boron composition and thermomechanical history were subjected to a series of short-time (induction) and long-time (furnace) heat treatments followed by scanning electron microscopy/electron backscatter diffraction and quantitative metallography. The size of the (pinned) gamma grains exhibited a limited dependence on heating rate and soak time at peak temperature, and it was generally smaller than the predictions based on the classic Smith-Zener model. The differences were rationalized in terms of stereological and pinning-particle location effects. Observations of limited coarsening of the carbide/boride pinning particles were interpreted in the context of prior experimental observations and a modified Lifshitz-Slyosov-Wagner model applied previously for the coarsening of compound phases in steels.

  16. Two phase titanium aluminide alloy

    Energy Technology Data Exchange (ETDEWEB)

    Deevi, Seetharama C. (Midlothian, VA); Liu, C. T. (Oak Ridge, TN)

    2001-01-01

    A two-phase titanic aluminide alloy having a lamellar microstructure with little intercolony structures. The alloy can include fine particles such as boride particles at colony boundaries and/or grain boundary equiaxed structures. The alloy can include alloying additions such as .ltoreq.10 at % W, Nb and/or Mo. The alloy can be free of Cr, V, Mn, Cu and/or Ni and can include, in atomic %, 45 to 55% Ti, 40 to 50% Al, 1 to 5% Nb, 0.3 to 2% W, up to 1% Mo and 0.1 to 0.3% B. In weight %, the alloy can include 57 to 60% Ti, 30 to 32% Al, 4 to 9% Nb, up to 2% Mo, 2 to 8% W and 0.02 to 0.08% B.

  17. Molecular and polymeric ceramic precursors. Progress report, December 1, 1990--November 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Sneddon, L.G.

    1993-05-01

    The development of new methods for the production of complex materials is one of the most important problems in modern solid state chemistry and materials science. This project is attempting to apply the synthetic principles which have evolved in inorganic and organometallic chemistry to the production of technologically important non-oxide ceramics, such as boron nitride, boron carbide and metal borides. Our recent work has now resulted in the production of new polymer systems, including poly(B-vinylborazine), polyvinylpentaborane and polyborazylene, that have proven to be high yield precursors to boron-based ceramic materials. Current work s now directed toward the synthesis of new types of molecular and polymeric boron-containing species and an exploration of the solid state properties of the ceramics that have been produced in these studies.

  18. Review of Thermal Spray Coating Applications in the Steel Industry: Part 2—Zinc Pot Hardware in the Continuous Galvanizing Line

    Science.gov (United States)

    Matthews, S.; James, B.

    2010-12-01

    This two-part article series reviews the application of thermal spray coating technology in the production of steel and steel sheet products. Part 2 of this article series is dedicated to coating solutions in the continuous galvanizing line. The corrosion mechanisms of Fe- and Co-based bulk materials are briefly reviewed as a basis for the development of thermal spray coating solutions. WC-Co thermal spray coatings are commonly applied to low Al-content galvanizing hardware due to their superior corrosion resistance compared to Fe and Co alloys. The effect of phase degradation, carbon content, and WC grain size are discussed. At high Al concentrations, the properties of WC-Co coatings degrade significantly, leading to the application of oxide-based coatings and corrosion-resistant boride containing coatings. The latest results of testing are summarized, highlighting the critical coating parameters.

  19. High energy milling of alumina synthesized by combustion reaction using attritor mill vertical axis: influence of rotation speed; Moagem de alta energia de alumina sintetizada por reacao de combustao utilizando moinho atritor de eixo vertical: influencia da velocidade de rotacao

    Energy Technology Data Exchange (ETDEWEB)

    Silva, M.C. da; Silva, F.N.; Costa, A.C.F.M. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais; Costa, G.B. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Producao; Freitas, N.L. de, E-mail: normanda@ufcg.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Tecnologia do Desenvolvimento

    2014-07-01

    The use of a reactive high energy milling for the synthesis of ceramic powders of metal oxides, carbides, borides, nitrides or mixtures of ceramics or ceramic and metal compounds have been widely reported. The objective of this study is to assess how high energy ball milling (not reactive) using different rotations, 300, 400 and 500 rpm, alter the structure and morphology of alpha-alumina powders synthesized by combustion reaction. Time and temperature of the combustion reaction has been reported for the synthesis of aluminas. The samples of unmilled and milled alumina were characterized by XRD, SEM and particle size analysis. The results showed that the maximum reaction temperature reached was 598°C. The variation of the rotation of the mill did not affect the majority alpha-Al2O3 by stable crystal phase all samples. The median particle diameter of the milled samples at different speeds decreased with respect to unground sample. (author)

  20. Standard practice for electrolytic extraction of phases from Ni and Ni-Fe base superalloys using a hydrochloric-methanol electrolyte

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1995-01-01

    1.1 This practice covers a procedure for the isolation of carbides, borides, TCP (topologically close-packed), and GCP (geometrically close-packed) phases (Note 1) in nickel and nickel-iron base gamma prime strengthened alloys. Contamination of the extracted residue by coarse matrix (gamma) or gamma prime particles, or both, reflects the condition of the alloy rather than the techniques mentioned in this procedure. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  1. Effect of Laser Power on Metallurgical, Mechanical and Tribological Characteristics of Hardfaced Surfaces of Nickel-Based Alloy

    Science.gov (United States)

    Gnanasekaran, S.; Padmanaban, G.; Balasubramanian, V.

    2017-10-01

    In this present work, nickel based alloy was deposited on 316 LN austenitic stainless steel (ASS) by a laser hardfacing technique to investigate the influence of laser power on macrostructure, microstructure, microhardness, dilution and wear characteristics. The laser power varied from 1.1 to 1.9 kW. The phase constitution, microstructure and microhardness were examined by optical microscope, scanning electron microscopy, energy dispersion spectroscopy and Vickers microhardness tester. The wear characteristics of the hardfaced surfaces and substrate were evaluated at room temperature (RT) under dry sliding wear condition (pin-on-disc). The outcome demonstrates that as the laser power increases, dilution increases and hardness of the deposit decreases. This is because excess heat melts more volume of substrate material and increases the dilution; subsequently it decreases the hardness of the deposit. The microstructure of the deposit is characterized by Ni-rich carbide, boride and silicide.

  2. Design for low-cost gas metal arc weld-based aluminum 3-D printing

    Science.gov (United States)

    Haselhuhn, Amberlee S.

    Additive manufacturing, commonly known as 3-D printing, has the potential to change the state of manufacturing across the globe. Parts are made, or printed, layer by layer using only the materials required to form the part, resulting in much less waste than traditional manufacturing methods. Additive manufacturing has been implemented in a wide variety of industries including aerospace, medical, consumer products, and fashion, using metals, ceramics, polymers, composites, and even organic tissues. However, traditional 3-D printing technologies, particularly those used to print metals, can be prohibitively expensive for small enterprises and the average consumer. A low-cost open-source metal 3-D printer has been developed based upon gas metal arc weld (GMAW) technology. Using this technology, substrate release mechanisms have been developed, allowing the user to remove a printed metal part from a metal substrate by hand. The mechanical and microstructural properties of commercially available weld alloys were characterized and used to guide alloy development in 4000 series aluminum-silicon alloys. Wedge casting experiments were performed to screen magnesium, strontium, and titanium boride alloying additions in hypoeutectic aluminum-silicon alloys for their properties and the ease with which they could be printed. Finally, the top performing alloys, which were approximately 11.6% Si modified with strontium and titanium boride were cast, extruded, and drawn into wire. These wires were printed and the mechanical and microstructural properties were compared with those of commercially available alloys. This work resulted in an easier-to-print aluminum-silicon-strontium alloy that exhibited lower porosity, equivalent yield and tensile strengths, yet nearly twice the ductility compared to commercial alloys.

  3. Applying an electron counting rule to screen prospective thermoelectric alloys: The thermoelectric properties of YCrB{sub 4} and Er{sub 3}CrB{sub 7}-type phases

    Energy Technology Data Exchange (ETDEWEB)

    Simonson, J.W., E-mail: jws9n@virginia.ed [Department of Physics, University of Virginia, 382 McCormick Rd., Charlottesville, VA 22904-4714 (United States); Poon, S.J. [Department of Physics, University of Virginia, 382 McCormick Rd., Charlottesville, VA 22904-4714 (United States)

    2010-08-13

    An electron counting rule, which was recently expanded to study molecular organometallics, boranes, and metallocenes, is utilized herein to predict the formation of a semiconducting gap or pseudo-gap in the density of states of deltahedral crystalline solids at or near the Fermi energy. It is suggested that this rule may be exploited to screen intermetallic compounds for prospective thermoelectric materials. The rule was applied to several structure types of known deltahedral boride and borocarbide compounds, and its predictions were compared to those of first principles electronic structure calculations when such were available in the literature or to published reports of transport properties. In addition, the rule has been used to predict the properties of several materials for which the electronic structure and properties have not hitherto been reported. In accordance with these predictions, layered ternary boride intermetallic compounds with structure types YCrB{sub 4} and Er{sub 3}CrB{sub 7} were synthesized, and the electrical resistivity and Seebeck coefficients of these alloys were measured from room temperature to 1100 K. Alloys of composition RMB{sub 4} (R = Y, Gd, Ho; M = Cr, Mo, W) were found to be n-type semiconductors and to exhibit thermopower up to {approx}70-115 {mu}V/K; the band gap was estimated to range from 0.17 to 0.28 eV, depending on composition. Undoped YCrB{sub 4} was measured to have a maximum power factor of 6.0 {mu}W/cm K{sup 2} at 500 K and Fe-doped YMoB{sub 4} of 2.4 {mu}W/cm K{sup 2} near 1000 K.

  4. Responsive hybrid inorganic-organic system derived from lanthanide luminescence

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Zhan [School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Zheng, Yuhui, E-mail: yhzheng78@scnu.edu.cn [School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Jiang, Lasheng; Yang, Jinglian [School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Wang, Qianming, E-mail: qmwang@scnu.edu.cn [Key Laboratory of Theoretical Chemistry of Environment, Ministry of Education, School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China); Guangzhou Key Laboratory of Materials for Energy Conversion and Storage, Guangzhou 510006 (China)

    2016-05-15

    Highlights: • A novel covalent hybrid material was used to detect hemoglobin. • All the recognition experiments were performed in buffer solution. • Porous nano-structures was extensively studied for the recognition. - Abstract: Terbium ions were incorporated into new organic-inorganic matrices to achieve intense green emissions. Hemoglobin (HB) interactions lead to dramatic changes in the luminescence emission intensities. Infrared spectra, morphological studies and photoluminescence give information for the speciation and process of hemoglobin additions. The porous material has a large specific surface area of 351 cm{sup 2}/g and the detection limit for HB (0.7 μM) was much lower than its physical doped material (8 μM). This promising hybrid material will lead to the design of versatile optical probes that are efficiently responding to the external targets.

  5. Optical fiber sensor for low dose gamma irradiation monitoring

    Science.gov (United States)

    de Andrés, Ana I.; Esteban, Ã.`scar; Embid, Miguel

    2016-05-01

    An optical fiber gamma ray detector is presented in this work. It is based on a Terbium doped Gadolinium Oxysulfide (Gd2O2S:Tb) scintillating powder which cover a chemically etched polymer fiber tip. This etching improves the fluorescence gathering by the optical fiber. The final diameter has been selected to fulfill the trade-off between light gathering and mechanical strength. Powder has been encapsulated inside a microtube where the fiber tip is immersed. The sensor has been irradiated with different air Kerma doses up to 2 Gy/h with a 137Cs source, and the spectral distribution of the fluorescence intensity has been recorded in a commercial grade CCD spectrometer. The obtained signal-to-noise ratio is good enough even for low doses, which has allowed to reduce the integration time in the spectrometer. The presented results show the feasibility for using low cost equipment to detect/measure ionizing radiation as gamma rays are.

  6. See Also:physica status solidi (b)physica status solidi (c)Copyright © 2004 WILEY-VCH Verlag GmbH & Co. KGaA, WeinheimGet Sample CopyFree Online Trial -->Recommend to Your LibrarianSave Title to My ProfileSet E-Mail Alert Journal subnav -->var homepagelinks = new Array(new Array("Journal Home","/cgi-bin/jhome/40000761",""),new Array("Issues","/cgi-bin/jtoc/40000761/",""),new Array("Early View","/cgi-bin/jeview/40000761/",""),new Array("News","/cgi-bin/jabout/40000761/news/index.html",""),new Array("Reviews","/cgi-bin/jabout/40000761/reviews.html",""),new Array("Read Cover Story","/cgi-bin/jabout/40000761/cover/2231/current.html","e"),new Array("","","s"),new Array("Product Information","/cgi-bin/jabout/40000761/2231_info.html",""),new Array("Editorial Board","/cgi-bin/jabout/40000761/edbd.html",""),new Array("For Authors","/cgi-bin/jabout/40000761/authors.html",""),new Array("For Referees","/cgi-bin/jabout/40000761/refserv.html",""),new Array("Subscribe","http://jws-edcv.wiley.com/jcatalog/JournalsCatalogOrder/JournalOrder?PRINT_ISSN=0031-8965",""),new Array("Contact","/cgi-bin/jabout/40000761/contact.html",""),new Array("Online Submission","http://www.manuscriptxpress.org/osm/",""),new Array("","","x"));writeJournalLinks("", "40000761");Journal subnav -->journal info area -->journal info area --> Previous Issue | Next Issue >Volume 201, Issue12 (September 2004)Articles in the Current Issue:article list -->Rapid Research NoteEffects of high dose proton irradiation on the electrical performance of ZnO Schottky diodes

    Science.gov (United States)

    Khanna, Rohit; Ip, K.; Allums, K. K.; Baik, K.; Abernathy, C. R.; Pearton, S. J.; Heo, Y. W.; Norton, D. P.; Ren, F.; Dwivedi, R.; Fogarty, T. N.; Wilkins, R.

    2004-09-01

    The preparation and characterization of terbium doped zinc aluminate photoluminescent films obtained by ultrasonic spray pyrolysis deposition process are described. Variations on doping concentrations in the start spraying solution and substrate temperatures were studied. XRD measurements on these films showed that the crystalline structure depends on the substrate temperature. For an excitation wavelength of 242 nm, all the photoluminescence spectra show peaks located at 488 nm, 546 nm, 589 nm and 621 nm. The photoluminescence intensity reaches values practically constant for the samples deposited at substrate temperatures higher than 400 °C. In this case, concentration quenching of the photoluminescence appears at doping concentrations greater than 0.93 atomic percent into the films. The surface morphology characteristics of the films deposited on glass and silicon substrates, as a function of the deposition temperature, are presented.

  7. Luminescent lanthanide chelates and methods of use

    Science.gov (United States)

    Selvin, Paul R.; Hearst, John

    1997-01-01

    The invention provides lanthanide chelates capable of intense luminescence. The celates comprise a lanthanide chelator covalently joined to a coumarin-like or quinolone-like sensitizer. Exemplary sensitzers include 2- or 4-quinolones, 2- or 4-coumarins, or derivatives thereof e.g. carbostyril 124 (7-amino-4-methyl-2-quinolone), coumarin 120 (7-amino-4-methyl-2-coumarin), coumarin 124 (7-amino-4-(trifluoromethyl)-2-coumarin), aminomethyltrimethylpsoralen, etc. The chelates form high affinity complexes with lanthanides, such as terbium or europium, through chelator groups, such as DTPA. The chelates may be coupled to a wide variety of compounds to create specific labels, probes, diagnostic and/or therapeutic reagents, etc. The chelates find particular use in resonance energy transfer between chelate-lanthanide complexes and another luminescent agent, often a fluorescent non-metal based resonance energy acceptor. The methods provide useful information about the structure, conformation, relative location and/or interactions of macromolecules.

  8. Creating infinite contrast in fluorescence microscopy by using lanthanide centered emission

    DEFF Research Database (Denmark)

    R. Carro-Temboury, Miguel; Arppe, Riikka Matleena; Hempel, Casper

    2017-01-01

    for completely removing the background signal in spectrally resolved fluorescence microscopy. The methodology is applicable for all probes with narrow and well-defined emission bands (Full width half-maximum lanthanide based probes exploiting the narrow emission lines of europium......(III) and terbium(III) ions. We used a model system with zeolites doped with lanthanides immobilized in a polymer stained with several fluorescent dyes regularly used in bioimaging. After smoothing the spectral data recorded in each pixel, they are differentiated. Method I is based on the direct sum of the gradient......, while method II resolves the fluorescent signal by subtracting a background calculated via the gradient. Both methods improve signal-to-background ratio significantly and we suggest that spectral imaging of lanthanide-centered emission can be used as a tool to obtain absolute contrast in bioimaging....

  9. Luminescent Lanthanide Metal Organic Frameworks for cis-Selective Isoprene Polymerization Catalysis

    Directory of Open Access Journals (Sweden)

    Samantha Russell

    2015-11-01

    Full Text Available In this study, we are combining two areas of chemistry; solid-state coordination polymers (or Metal-Organic Framework—MOF and polymerization catalysis. MOF compounds combining two sets of different lanthanide elements (Nd3+, Eu3+/Tb3+ were used for that purpose: the use of neodymium was required due to its well-known catalytic properties in dienes polymerization. A second lanthanide, europium or terbium, was included in the MOF structure with the aim to provide luminescent properties. Several lanthanides-based MOF meeting these criteria were prepared according to different approaches, and they were further used as catalysts for the polymerization of isoprene. Stereoregular cis-polyisoprene was received, which in some cases exhibited luminescent properties in the UV-visible range.

  10. Method for compensation of thermally induced modal distortions in the input optical components of gravitational wave interferometers

    CERN Document Server

    Müller, G; Guagliardo, D; McFeron, D; Lundock, R; Reitze, D H; Tanner, D B

    2002-01-01

    The next generation of interferometric gravitational wave detectors will employ laser powers approaching 200 W to increase shot-noise limited sensitivity. Optical components that transmit the laser light will exhibit increased thermal lensing induced by bulk absorption and concomitant changes in the material refractive index, resulting in significant changes in the modal characteristics of the beam. Key interferometer components such as electro-optic modulators and Faraday isolators are particularly at risk, since they possess relatively large absorption coefficients. We present a method for passive correction of thermally induced optical path length (DELTA LAMBDA) changes induced by absorption in transmissive optical components. Our method relies on introducing material in the optical path that possesses a negative index temperature derivative, thereby inducing a compensating opposite DELTA LAMBDA. We experimentally demonstrate a factor of 10 reduction in higher order spatial mode generation for terbium gall...

  11. High-density scintillating glasses for a proton imaging detector

    Science.gov (United States)

    Tillman, I. J.; Dettmann, M. A.; Herrig, V.; Thune, Z. L.; Zieser, A. J.; Michalek, S. F.; Been, M. O.; Martinez-Szewczyk, M. M.; Koster, H. J.; Wilkinson, C. J.; Kielty, M. W.; Jacobsohn, L. G.; Akgun, U.

    2017-06-01

    High-density scintillating glasses are proposed for a novel proton-imaging device that can improve the accuracy of the hadron therapy. High-density scintillating glasses are needed to build a cost effective, compact calorimeter that can be attached to a gantry. This report summarizes the study on Europium, Terbium, and Cerium-doped scintillating glasses that were developed containing heavy elements such as Lanthanum, Gadolinium, and Tungsten. The density of the samples reach up to 5.9 g/cm3, and their 300-600 nm emission overlaps perfectly with the peak cathode sensitivity of the commercial photo detectors. The developed glasses do not require any special quenching and can be poured easily, which makes them a good candidate for production in various geometries. Here, the glass making conditions, preliminary tests on optical and physical properties of these scintillating, high-density, oxide glasses developed for a novel medical imaging application are reported.

  12. Heat-Flux Gage thermophosphor system

    Energy Technology Data Exchange (ETDEWEB)

    Tobin, K.W.

    1991-08-01

    This document describes the installation, hardware requirements, and application of the Heat-Flux Gage (Version 1.0) software package developed by the Oak Ridge National Laboratory, Applied Technology Division. The developed software is a single component of a thermographic phosphor-based temperature and heat-flux measurement system. The heat-flux transducer was developed by EG G Energy Measurements Systems and consists of a 1- by 1-in. polymethylpentene sheet coated on the front and back with a repeating thermographic phosphor pattern. The phosphor chosen for this application is gadolinium oxysulphide doped with terbium. This compound has a sensitive temperature response from 10 to 65.6{degree}C (50--150{degree}F) for the 415- and 490-nm spectral emission lines. 3 refs., 17 figs.

  13. Radioluminescence of rare-earth doped aluminum oxide

    Energy Technology Data Exchange (ETDEWEB)

    Santiago, M.; Molina, P. [Universidad Nacional del Centro de la Provincia de Buenos Aires, Instituto de Fisica Arroyo Seco, Pinto 399, 7000 Tandil (Argentina); Barros, V. S.; Khoury, H. J.; Elihimas, D. R., E-mail: msantiag@exa.unicen.edu.ar [Universidade Federal de Pernambuco, Departamento de Energia Nuclear, Av. Prof. Luiz Freire 1000, Recife, PE 50740-540 (Brazil)

    2011-10-15

    Carbon-doped aluminum oxide (Al{sub 2}O{sub 3}:C) is one of the most used radioluminescence (Rl) materials for fiberoptic dosimetry due to its high efficiency and commercial availability. However, this compound presents the drawback of emitting in the spectral region, where the spurious radioluminescence of fibers is also important. In this work, the radioluminescence response of rare-earth doped Al{sub 2}O{sub 3} samples has been evaluated. The samples were prepared by mixing stoichiometric amounts of aluminum nitrate, urea and dopants with different amounts of terbium, samarium, cerium and thulium nitrates varying from 0 to 0.15 mo 1%. The influence of the different activators on the Rl spectra has been investigated in order to determine the feasibility of using these compounds for Rl fiberoptic dosimetry. (Author)

  14. Messenger RNA Detection in Leukemia Cell lines by Novel Metal-Tagged in situ Hybridization using Inductively Coupled Plasma Mass Spectrometry.

    Science.gov (United States)

    Ornatsky, Olga I; Baranov, Vladimir I; Bandura, Dmitry R; Tanner, Scott D; Dick, John

    2006-01-01

    Conventional gene expression profiling relies on using fluorescent detection of hybridized probes. Physical characteristics of fluorophores impose limitations on achieving a highly multiplex gene analysis of single cells. Our work demonstrates the feasibility of using metal-tagged in situ hybridization for mRNA detection by inductively coupled plasma mass spectrometry (ICP-MS). ICP-MS as an analytical detector has a number of unique and relevant properties: 1) metals and their stable isotopes generate non-overlapping distinct signals that can be detected simultaneously; 2) these signals can be measured over a wide dynamic range; 3) ICP-MS is quantitative and very sensitive. We used commercial antibodies conjugated to europium (Eu) and gold together with biotinylated oligonucleotide probes reacted with terbium-labeled streptavidin to demonstrate simultaneous mRNA and protein detection by ICP-MS in leukemia cells.

  15. Magnetic behaviour of TbPc2 single-molecule magnets chemically grafted on silicon surface.

    Science.gov (United States)

    Mannini, Matteo; Bertani, Federico; Tudisco, Cristina; Malavolti, Luigi; Poggini, Lorenzo; Misztal, Kasjan; Menozzi, Daniela; Motta, Alessandro; Otero, Edwige; Ohresser, Philippe; Sainctavit, Philippe; Condorelli, Guglielmo G; Dalcanale, Enrico; Sessoli, Roberta

    2014-08-11

    Single-molecule magnets (SMMs) are among the most promising molecular systems for the development of novel molecular electronics based on spin transport. Going beyond investigations focused on physisorbed SMMs, in this work the robust grafting of terbium(III) bis(phthalocyaninato) complexes to a silicon surface from a diluted solution is achieved by rational chemical design yielding the formation of a partially oriented monolayer on the conducting substrate. Here by exploiting the surface sensitivity of X-ray circular magnetic dichroism, we evidence an enhancement of the magnetic bistability of this SMM, in contrast to the dramatic reduction of the magnetic hysteresis that characterizes monolayer deposits evaporated on noble and ferromagnetic metals. Photoelectron spectroscopy investigations and density functional theory analysis suggest a non-innocent role played by the silicon substrate, evidencing the potentiality of this approach for robust integration of bistable magnetic molecules in electronic devices.

  16. Penicillium expansum Link strain for a biometallurgical method to recover REEs from WEEE.

    Science.gov (United States)

    Di Piazza, Simone; Cecchi, Grazia; Cardinale, Anna Maria; Carbone, Cristina; Mariotti, Mauro Giorgio; Giovine, Marco; Zotti, Mirca

    2017-02-01

    Due to the wide range of applications in high-tech solutions, Rare Earth Elements (REEs) have become object of great interest. In the last years several studies regarding technologies for REE extraction from secondary resources have been carried out. In particular biotechnologies, which use tolerant and accumulator microorganisms to recover and recycle precious metals, are replacing traditional methods. This paper describes an original biometallurgical method to recover REEs from waste electrical and electronic equipment (WEEE) by using a strain of Penicillium expansum Link isolated from an ecotoxic metal contaminated site. The resulting product is a high concentrated solution of Lanthanum (up to 390ppm) and Terbium (up to 1520ppm) obtained from WEEE. Under this perspective, the proposed protocol can be considered a method of recycling exploiting biometallurgy. Finally, the process is the subject of the Italian patent application n. 102015000041404 submitted by the University of Genoa. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Infrared Spectroscopic Characterization of Photoluminescent Polymer Nanocomposites

    Directory of Open Access Journals (Sweden)

    Kyle Gipson

    2015-01-01

    Full Text Available Organicallycoated inorganic nanoparticles were synthesized to produce photoluminescent nanocomposites based on a polymethyl methacrylate (PMMA matrix. The nanoparticles comprised organic ligands (acetylsalicylic acid, ASA, and 2-picolinic acid, PA attached to the lanthanum trifluoride (LaF3 host crystals that were doped with optically active terbium III (Tb3+ and synthesized using solution-based methods. The ligands were employed to functionalize the surface of Tb3+:LaF3 nanocrystals to aid in dispersing the nanoparticles. In order to confirm the presence of the constituents within the inorganic-organic system, the nanoparticles were characterized by infrared spectroscopy and energy-dispersive X-ray spectroscopy. Absorption peaks observed from infrared spectroscopy for all the polymer nanocomposites loaded with organic surface treated nanocrystals exhibited peaks that were not present in undoped PMMA but were characteristic of the dopant and the ligand.

  18. Complex logic functions implemented with quantum dot bionanophotonic circuits.

    Science.gov (United States)

    Claussen, Jonathan C; Hildebrandt, Niko; Susumu, Kimihiro; Ancona, Mario G; Medintz, Igor L

    2014-03-26

    We combine quantum dots (QDs) with long-lifetime terbium complexes (Tb), a near-IR Alexa Fluor dye (A647), and self-assembling peptides to demonstrate combinatorial and sequential bionanophotonic logic devices that function by time-gated Förster resonance energy transfer (FRET). Upon excitation, the Tb-QD-A647 FRET-complex produces time-dependent photoluminescent signatures from multi-FRET pathways enabled by the capacitor-like behavior of the Tb. The unique photoluminescent signatures are manipulated by ratiometrically varying dye/Tb inputs and collection time. Fluorescent output is converted into Boolean logic states to create complex arithmetic circuits including the half-adder/half-subtractor, 2:1 multiplexer/1:2 demultiplexer, and a 3-digit, 16-combination keypad lock.

  19. Creating infinite contrast in fluorescence microscopy by using lanthanide centered emission

    DEFF Research Database (Denmark)

    R. Carro-Temboury, Miguel; Arppe, Riikka Matleena; Hempel, Casper

    2017-01-01

    The popularity of fluorescence microscopy arises from the inherent mode of action, where the fluorescence emission from probes is used to visualize selected features on a presumed dark background. However, the background is rarely truly dark, and image processing and analysis is needed to enhance...... for completely removing the background signal in spectrally resolved fluorescence microscopy. The methodology is applicable for all probes with narrow and well-defined emission bands (Full width half-maximum emission lines of europium......(III) and terbium(III) ions. We used a model system with zeolites doped with lanthanides immobilized in a polymer stained with several fluorescent dyes regularly used in bioimaging. After smoothing the spectral data recorded in each pixel, they are differentiated. Method I is based on the direct sum of the gradient...

  20. TbNb6Sn6: the first ternary compound from the rare earth–niobium–tin system

    Directory of Open Access Journals (Sweden)

    Viktor Hlukhyy

    2010-12-01

    Full Text Available The title compound, terbium hexaniobium hexastannide, TbNb6Sn6, is the first ternary compound from the rare earth–niobium–tin system. It has the HfFe6Ge6 structure type, which can be analysed as an intergrowth of the Zr4Al3 and CaCu5 structures. All the atoms lie on special positions; their coordination geometries and site symmetries are: Tb (dodecahedron 6/mmm; Nb (distorted icosahedron 2mm; Sn (Frank–Caspar polyhedron, CN = 14–15 6mm and overline{6}m2; Sn (distorted icosahedron overline{6}m2. The structure contains a graphite-type Sn network, Kagome nets of Nb atoms, and Tb atoms alternating with Sn2 dumbbells in the channels.