Multijunction Photovoltaic Technologies for High-Performance Concentrators: Preprint

Energy Technology Data Exchange (ETDEWEB)

McConnell, R.; Symko-Davies, M.

2006-05-01

Multijunction solar cells provide high-performance technology pathways leading to potentially low-cost electricity generated from concentrated sunlight. The National Center for Photovoltaics at the National Renewable Energy Laboratory has funded different III-V multijunction solar cell technologies and various solar concentration approaches. Within this group of projects, III-V solar cell efficiencies of 41% are close at hand and will likely be reported in these conference proceedings. Companies with well-developed solar concentrator structures foresee installed system costs of $3/watt--half of today's costs--within the next 2 to 5 years as these high-efficiency photovoltaic technologies are incorporated into their concentrator photovoltaic systems. These technology improvements are timely as new large-scale multi-megawatt markets, appropriate for high performance PV concentrators, open around the world.

48 CFR 970.3102-05-30-70 - Patent costs and technology transfer costs.

Science.gov (United States)

2010-10-01

... technology transfer costs. 970.3102-05-30-70 Section 970.3102-05-30-70 Federal Acquisition Regulations System... Principles and Procedures 970.3102-05-30-70 Patent costs and technology transfer costs. (a) For management and operating contracts that do not include the clause at 970.5227-3, Technology Transfer Mission, the...

Cost-saving production technologies and partial ownership

OpenAIRE

Juan Carlos Barcena-Ruiz; Norma Olaizola

2007-01-01

This work analyzes the incentives to acquire cost-saving production technologies when cross-participation exists at ownership level. We show that cross-participation reduces the incentives to adopt the cost-saving production technology.

Research and deployment priorities for renewable technologies: Quantifying the importance of various renewable technologies for low cost, high renewable electricity systems in an Australian case study

International Nuclear Information System (INIS)

Riesz, Jenny; Elliston, Ben

2016-01-01

This study aims to identify research priorities to enable low cost, high renewable power systems. An evolutionary program optimises the mix of technologies in 100% renewable energy portfolios (RE) in the Australian National Electricity Market. Various technologies are reduced in availability to determine their relative importance for achieving low costs. The single most important factor is found to be the integration of large quantities of wind; therefore wind integration is identified as a research priority. In contrast, photovoltaics are found to “saturate” the system at less than 10% of total energy (in the absence of storage or demand management, installation of further photovoltaics does not contribute significant further value). This indicates that policies to promote utility-scale photovoltaics should be considered in partnership with complementary measures (such as demand side participation and storage). Biofuelled gas turbines are found to be important; a complete absence of bioenergy increases costs by AU$20–30/MWh, and even having only 0.1 TWh per year of bioenergy available reduces average costs by AU$3–4/MWh. Limits on the non-synchronous penetration (NSP) are found to be relatively expensive, suggesting a significant research priority around finding alternative approaches to providing synchronous services, such as inertia. Geothermal and concentrating solar thermal technologies do not appear essential as long as sufficient wind and peaking bioenergy is available. - Highlights: • Photovoltaics saturate early, suggesting they need complementary measures. • Biofuelled gas turbines or another peaking technology are important for low costs. • Limits on the non-synchronous penetration are relatively expensive.

Technology for low cost solid rocket boosters.

Science.gov (United States)

Ciepluch, C.

1971-01-01

A review of low cost large solid rocket motors developed at the Lewis Research Center is given. An estimate is made of the total cost reduction obtainable by incorporating this new technology package into the rocket motor design. The propellant, case material, insulation, nozzle ablatives, and thrust vector control are discussed. The effect of the new technology on motor cost is calculated for a typical expandable 260-in. booster application. Included in the cost analysis is the influence of motor performance variations due to specific impulse and weight changes. It is found for this application that motor costs may be reduced by up to 30% and that the economic attractiveness of future large solid rocket motors will be improved when the new technology is implemented.

Cost-estimate guidelines for advanced nuclear power technologies

International Nuclear Information System (INIS)

Delene, J.G.; Hudson, C.R.

1993-01-01

Various advanced power plant concepts are currently under development. These include several advanced light water reactors as well as the modular high-temperature gas-cooled reactor and the advanced liquid-metal reactor. One measure-of the attractiveness of a new concept is cost. Invariably, the cost of a new type of power plant will be compared with other alternative forms of electric generation. In order to make reasonable comparative assessments of competing technologies, consistent ground rules and assumptions must be applied when developing cost estimates. This paper describes the cost-estimate guidelines developed by Oak Ridge National Laboratory for the U.S. Department of Energy (DOE) to be used in developing cost estimates for the advanced nuclear reactors and how these guidelines relate to the DOE cost verification process

Mission possible: creating a technology infrastructure to help reduce administrative costs.

Science.gov (United States)

Alper, Michael

2003-01-01

Controlling administrative costs associated with managed care benefits has traditionally been considered a "mission impossible" in healthcare, with the unreasonably high cost of paperwork and administration pushing past the $420 billion mark. Why administrative costs remain a critical problem in healthcare while other industries have alleviated their administrative burdens must be carefully examined. This article looks at the key factors contributing to high administrative costs and how these costs can be controlled in the future with "mission possible" tools, including business process outsourcing, IT outsourcing, technology that helps to bring "consumerism" to managed care, and an IT infrastructure that improves quality and outcomes.

Market diffusion, technological learning, and cost-benefit dynamics of condensing gas boilers in the Netherlands

NARCIS (Netherlands)

Weiss, M.; Dittmar, L.; Junginger, H.M.; Patel, M.K.; Blok, K.

2009-01-01

High costs often prevent the market diffusion of novel and efficient energy technologies. Monitoring cost and price decline for these technologies is thus important in order to establish effective energy policy. Here, we present experience curves and cost-benefit analyses for condensing gas boilers

Future costs of key low-carbon energy technologies: Harmonization and aggregation of energy technology expert elicitation data

International Nuclear Information System (INIS)

Baker, Erin; Bosetti, Valentina; Anadon, Laura Diaz; Henrion, Max; Aleluia Reis, Lara

2015-01-01

In this paper we standardize, compare, and aggregate results from thirteen surveys of technology experts, performed over a period of five years using a range of different methodologies, but all aiming at eliciting expert judgment on the future cost of five key energy technologies and how future costs might be influenced by public R&D investments. To enable researchers and policy makers to use the wealth of collective knowledge obtained through these expert elicitations we develop and present a set of assumptions to harmonize them. We also aggregate expert estimates within each study and across studies to facilitate the comparison. The analysis showed that, as expected, technology costs are expected to go down by 2030 with increasing levels of R&D investments, but that there is not a high level of agreement between individual experts or between studies regarding the technology areas that would benefit the most from R&D investments. This indicates that further study of prospective cost data may be useful to further inform R&D investments. We also found that the contributions of additional studies to the variance of costs in one technology area differed by technology area, suggesting that (barring new information about the downsides of particular forms of elicitations) there may be value in not only including a diverse and relatively large group of experts, but also in using different methods to collect estimates. - Highlights: • Harmonization of unique dataset on probabilistic evolution of key energy technologies. • Expectations about the impact of public R&D investments on future costs. • Highlighting the key uncertainties and a lack of consensus on cost evolution

Parametric Cost and Schedule Modeling for Early Technology Development

Science.gov (United States)

2018-04-02

Research NoteNational Security Rep rt PARAMETRIC MODELING FOR EARLY TECHNOLOGY DEVELOPMENT COST AND SCHEDULE Chuck...Alexander NSR_11x17_Cover_CostModeling_v8.indd 1 11/20/17 3:15 PM PARAMETRIC COST AND SCHEDULE MODELING FOR EARLY  TECHNOLOGY DEVELOPMENT Chuck...COST AND SCHEDULE MODELING FOR EARLY  TECHNOLOGY DEVELOPMENT iii Contents Figures

Photovoltaic technology, performance, manufacturing cost and markets

International Nuclear Information System (INIS)

Maycock, P.D.

1999-01-01

A comprehensive discussion of key aspects of photovoltaic energy conversion systems will provide the basis for forecasting PV module shipments from 1999 to 2010. Principal areas covered include: (1) Technology and Performance Status: The module efficiency and performance are described for commercial cell technologies including single crystal silicon, polycrystal silicon, ribbon silicon, film silicon on low cost substrate, amorphous silicon, copper indium diselenide, and cadmium telluride; (2) Manufacturing cost: 1999 costs for PV technologies in production (single crystal silicon, polycrystal silicon, and amorphous silicon) are developed. Manufacturing costs for 10--25 MW plants and 100 MW plants will be estimated; (3) The world PV market is summarized by region, top ten companies, and technology; and (4) Forecast of the World Market (seven market sectors) to 2010 will be presented. Key assumptions, price of modules, incentive programs, price of competing electricity generation will be detailed

Cost and performance of innovative remediation technologies

International Nuclear Information System (INIS)

Cummings, J.B.; Kingscott, J.W.; Fiedler, L.D.

1995-01-01

The selection and use of more cost-effective remedies requires better access to data on the performance and cost of technologies used in the field. To make data more widely available, the US Environmental Protection Agency is working jointly with member agencies of the Federal Remediation Technologies Round table to publish case studies of full-scale remediation and demonstration projects. EPA, DoD, and DOE have published case studies of cleanup projects primarily consisting of bioremediation, soil vapor extraction, and thermal desorption. Within the limits of this initial data set, the paper evaluates technology performance and cost. In the analysis of cost factors, the paper shows the use of a standardized Work Breakdown Structure (WBS). Use of the WBS will be important in future reporting of completed projects to facilitate cost comparison. The paper notes the limits to normalization and thus cross-site comparison which can be achieved using the WBS. The paper identifies conclusions from initial efforts to compile cost and performance data, highlights the importance of such efforts to the overall remediation effort, and discusses future cost and performance documentation efforts

Heat savings and heat generation technologies: Modelling of residential investment behaviour with local health costs

DEFF Research Database (Denmark)

Zvingilaite, Erika; Klinge Jacobsen, Henrik

2015-01-01

The trade-off between investing in energy savings and investing in individual heating technologies with high investment and low variable costs in single family houses is modelled for a number of building and consumer categories in Denmark. For each group the private economic cost of providing hea...... for private consumers decrease by 66% when all have the option to shift to the technology with lowest variable costs. © 2014 Elsevier Ltd. All Rights reserved......The trade-off between investing in energy savings and investing in individual heating technologies with high investment and low variable costs in single family houses is modelled for a number of building and consumer categories in Denmark. For each group the private economic cost of providing...

IMPACT OF HEALTH TECHNOLOGY ASSESSMENT IN LITIGATION CONCERNING ACCESS TO HIGH-COST DRUGS.

Science.gov (United States)

Aleman, Alicia; Perez Galan, Ana

2017-01-01

The impact of health technology assessment (HTA) in the judicialization of the right of health has not been deeply studied in Latin American countries. The purpose of this study is to review the process of judicialization of the access to high cost drugs in Uruguay and assess the impact HTAs have had on this process. The methodology used for this study included a comprehensive literature search in electronic databases, local journals, internal documents developed in the Ministry of Health, as well as conducting interviews with key informants. Judicialization of the access of high cost drugs has been increasing since 2010. The strategy of the Ministry of Health of Uruguay to decrease this problem included the organization of roundtables with judges and other stakeholders on the basis of HTA, the training of defense lawyers in the use and interpretation of HTA, and the participation of a professional who develops HTA in the preparation of the defense arguments. A year after the implementation of this strategy, 25 percent of writs of protection were won by the Ministry of Health. Even though the strategy implemented was effective in reducing the loss of litigations, it was not effective in reducing the growing number of writs of protection. It is essential to address this problem in a broad debate and to promote understanding between the parties.

Development of Manufacturing Technology to Accelerate Cost Reduction of Low Concentration and

Energy Technology Data Exchange (ETDEWEB)

Detrick, Adam [The Solaria Corporation, Fremont, CA (United States)

2017-09-27

The purpose of this project was to accelerate deployment of cost-effective US-based manufacturing of Solaria’s unique c-Si module technology. This effort successfully resulted in the development of US-based manufacturing technology to support two highly-differentiated, market leading product platforms. The project was initially predicated on developing Solaria’s low-concentration PV (LCPV) module technology which at the time of the award was uniquely positioned to exceed the SunShot price goal of $0.50/Wp for standard c-Si modules. The Solaria LCPV module is a 2.5x concentrator that leverages proven, high-reliability PV module materials and low silicon cell usage into a technology package that already had the lowest direct material cost and leading Levelized Cost of Electricity (LCOE). With over 25 MW commercially deployed globally, the Solaria module was well positioned to continue to lead in PV module cost reduction. Throughout the term of the contract, market conditions changed dramatically and so to did Solaria’s product offerings to support this. However, the manufacturing technology developed for the LCPV module was successfully leveraged and optimized to support two new and different product platforms. BIPV “PowerVision” and High-efficiency “PowerXT” modules. The primary barrier to enabling high-volume PV module manufacturing in the US is the high manual labor component in certain unique aspects of our manufacturing process. The funding was used to develop unique manufacturing automation which makes the manual labor components of these key processes more efficient and increase throughput. At the core of Solaria’s product offerings are its unique and proprietary techniques for dicing and re-arranging solar cells into modules with highly-differentiated characteristics that address key gaps in the c-Si market. It is these techniques that were successfully evolved and deployed into US-based manufacturing site with SunShot funding. Today, Solaria

Cost-Effectiveness of Old and New Technologies for Aneuploidy Screening.

Science.gov (United States)

Sinkey, Rachel G; Odibo, Anthony O

2016-06-01

Cost-effectiveness analyses allow assessment of whether marginal gains from new technology are worth increased costs. Several studies have examined cost-effectiveness of Down syndrome (DS) screening and found it to be cost-effective. Noninvasive prenatal screening also appears to be cost-effective among high-risk women with respect to DS screening, but not for the general population. Chromosomal microarray (CMA) is a genetic sequencing method superior to but more expensive than karyotype. In light of CMAs greater ability to detect genetic abnormalities, it is cost-effective when used for prenatal diagnosis of an anomalous fetus. This article covers methodology and salient issues of cost-effectiveness. Copyright © 2016 Elsevier Inc. All rights reserved.

Cost-effectiveness of nitrogen mitigation by alternative household wastewater management technologies.

Science.gov (United States)

Wood, Alison; Blackhurst, Michael; Hawkins, Troy; Xue, Xiaobo; Ashbolt, Nicholas; Garland, Jay

2015-03-01

Household wastewater, especially from conventional septic systems, is a major contributor to nitrogen pollution. Alternative household wastewater management technologies provide similar sewerage management services but their life cycle costs and nitrogen flow implications remain uncertain. This paper addresses two key questions: (1) what are the total costs, nitrogen mitigation potential, and cost-effectiveness of a range of conventional and alternative municipal wastewater treatment technologies, and (2) what uncertainties influence these outcomes and how can we improve our understanding of these technologies? We estimate a household nitrogen mass balance for various household wastewater treatment systems and combine this mass balance with life cycle cost assessment to calculate the cost-effectiveness of nitrogen mitigation, which we define as nitrogen removed from the local watershed. We apply our methods to Falmouth, MA, where failing septic systems have caused heightened eutrophication in local receiving water bodies. We find that flushing and dry (composting) urine-diversion toilets paired with conventional septic systems for greywater management demonstrate the lowest life cycle cost and highest cost-effectiveness (dollars per kilogram of nitrogen removed from the watershed). Composting toilets are also attractive options in some cases, particularly best-case nitrogen mitigation. Innovative/advanced septic systems designed for high-level nitrogen removal are cost-competitive options for newly constructed homes, except at their most expensive. A centralized wastewater treatment plant is the most expensive and least cost-effective option in all cases. Using a greywater recycling system with any treatment technology increases the cost without adding any nitrogen removal benefits. Sensitivity analysis shows that these results are robust considering a range of cases and uncertainties. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Low–Cost Bio-Based Carbon Fiber for High-Temperature Processing

Energy Technology Data Exchange (ETDEWEB)

Naskar, Amit K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Akato, Kokouvi M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Tran, Chau D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Paul, Ryan M. [GrafTech International Holdings, Inc., Brooklyn Heights, OH (United States); Dai, Xuliang [GrafTech International Holdings, Inc., Brooklyn Heights, OH (United States)

2017-02-01

GrafTech International Holdings Inc. (GTI), worked with Oak Ridge National Laboratory (ORNL) under CRADA No. NFE-15-05807 to develop lignin-based carbon fiber (LBCF) technology and to demonstrate LBCF performance in high-temperature products and applications. This work was unique and different from other reported LBCF work in that this study was application-focused and scalability-focused. Accordingly, the executed work was based on meeting criteria based on technology development, cost, and application suitability. The focus of this work was to demonstrate lab-scale LBCF from at least 4 different precursor feedstock sources that could meet the estimated production cost of $5.00/pound and have ash level of less than 500 ppm in the carbonized insulation-grade fiber. Accordingly, a preliminary cost model was developed based on publicly available information. The team demonstrated that 4 lignin samples met the cost criteria, as highlighted in Table 1. In addition, the ash level for the 4 carbonized lignin samples were below 500 ppm. Processing asreceived lignin to produce a high purity lignin fiber was a significant accomplishment in that most industrial lignin, prior to purification, had greater than 4X the ash level needed for this project, and prior to this work there was not a clear path of how to achieve the purity target. The lab scale development of LBCF was performed with a specific functional application in mind, specifically for high temperature rigid insulation. GTI is currently a consumer of foreignsourced pitch and rayon based carbon fibers for use in its high temperature insulation products, and the motivation was that LBCF had potential to decrease costs and increase product competitiveness in the marketplace through lowered raw material costs, lowered energy costs, and decreased environmental footprint. At the end of this project, the Technology Readiness Level (TRL) remained at 5 for LBCF in high temperature insulation.

Endogenous Technology Adoption and Medical Costs.

Science.gov (United States)

Lamiraud, Karine; Lhuillery, Stephane

2016-09-01

Despite the claim that technology has been one of the most important drivers of healthcare spending growth over the past decades, technology variables are rarely introduced explicitly in cost equations. Furthermore, technology is often considered exogenous. Using 1996-2007 panel data on Swiss geographical areas, we assessed the impact of technology availability on per capita healthcare spending covered by basic health insurance whilst controlling for the endogeneity of health technology availability variables. Our results suggest that medical research, patent intensity and the density of employees working in the medical device industry are influential factors for the adoption of technology and can be used as instruments for technology availability variables in the cost equation. These results are similar to previous findings: CT and PET scanner adoption is associated with increased healthcare spending, whilst increased availability of percutaneous transluminal coronary angioplasty facilities is associated with reductions in per capita spending. However, our results suggest that the magnitude of these relationships is much greater in absolute value than that suggested by previous studies that did not control for the possible endogeneity of the availability of technologies. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Technology strategy for cost-effective drilling and intervention; Technology Target Areas; TTA4 - Cost effective drilling and intervention

Energy Technology Data Exchange (ETDEWEB)

2007-07-01

The main goals of the OG21 initiative are to (1) develop new technology and knowledge to increase the value creation of Norwegian oil and gas resources and (2) enhance the export of Norwegian oil and gas technology. The OG21 Cost-effective Drilling and Intervention (CEDI) Technology Target Area (TTA) has identified some key strategic drilling and well intervention needs to help meet the goals of OG21. These key strategic drilling and well intervention needs are based on a review of present and anticipated future offshore-Norway drilling and well intervention conditions and the Norwegian drilling and well intervention industry. A gap analysis has been performed to assess the extent to which current drilling and well intervention research and development and other activities will meet the key strategic needs. Based on the identified strategic drilling and well intervention needs and the current industry res each and development and other activities, the most important technology areas for meeting the OG21 goals are: environment-friendly and low-cost exploration wells; low-cost methods for well intervention/sidetracks; faster and extended-reach drilling; deep water drilling, completion and intervention; offshore automated drilling; subsea and sub-ice drilling; drilling through basalt and tight carbonates; drilling and completion in salt formation. More specific goals for each area: reduce cost of exploration wells by 50%; reduce cost for well intervention/sidetracks by 50%; increase drilling efficiency by 40%; reduce drilling cost in deep water by 40 %; enable offshore automated drilling before 2012; enable automated drilling from seabed in 2020. Particular focus should be placed on developing new technology for low-cost exploration wells to stem the downward trends in the number of exploration wells drilled and the volume of discovered resources. The CEDI TTA has the following additional recommendations: The perceived gaps in addressing the key strategic drilling and

Low-cost high-quality crystalline germanium based flexible devices

KAUST Repository

Nassar, Joanna M.

2014-06-16

High performance flexible electronics promise innovative future technology for various interactive applications for the pursuit of low-cost, light-weight, and multi-functional devices. Thus, here we show a complementary metal oxide semiconductor (CMOS) compatible fabrication of flexible metal-oxide-semiconductor capacitors (MOSCAPs) with high-κ/metal gate stack, using a physical vapor deposition (PVD) cost-effective technique to obtain a high-quality Ge channel. We report outstanding bending radius ~1.25 mm and semi-transparency of 30%.

Low-cost high-quality crystalline germanium based flexible devices

KAUST Repository

Nassar, Joanna M.; Hussain, Aftab M.; Rojas, Jhonathan Prieto; Hussain, Muhammad Mustafa

2014-01-01

High performance flexible electronics promise innovative future technology for various interactive applications for the pursuit of low-cost, light-weight, and multi-functional devices. Thus, here we show a complementary metal oxide semiconductor (CMOS) compatible fabrication of flexible metal-oxide-semiconductor capacitors (MOSCAPs) with high-κ/metal gate stack, using a physical vapor deposition (PVD) cost-effective technique to obtain a high-quality Ge channel. We report outstanding bending radius ~1.25 mm and semi-transparency of 30%.

Cost-effective FITL technologies for small business and residential customers

Science.gov (United States)

Andersen, Niels E.; Woolnough, Peter; Seidenberg, Juergen; Ferreira, Mario F. S.

1995-02-01

FIRST is a RACE project where 5 main European telecoms operators, 4 equipment manufacturers and one university have joined up to define and test in a field trial in Portugal a cost effective Optical Access Network. The main design target has been a system which gives cost effective provision of wideband services for small and medium business customers. The system however, incorporates provision of telephone, ISDN and analog and digital video for residential customers as well. Technologies have been chosen with the objective of providing a simple, robust and flexible system where initial deployment costs are low and closely related to the service take up. The paper describes the main technical features of the system and network applications which shows how the system may be introduced in network planning. The system is based on Passive Optical Network technology where video is distributed in the 1550 nm window and telecoms services transmitted at 1300 nm in full duplex mode. The telecoms system provides high capacity, flexibility in loop length and robustness towards outside plant performance. The Subcarrier Multiple Access (SCMA) method is used for upstream transmission of bi-directional telecoms services. SCMA has advantages compared to the Time Division Multiple Access technology used in other systems. Bandwidth/cost tradeoff is better and the lower requirements to the outside plant increases the overall cost benefit. Optical beat noise due to overlapping of laser spectra which may be a problem for this technology has been addressed with success through the use of a suitable modulation and control technique. This technology is further validated in the field trial. The video system provides cost effective long distance transmission on standard fiber with externally modulated lasers and cascaded amplifiers. Coexistence of analog and digital video on one fiber with different modulation schemes i.e. BPSK, QPSK and 64 QAM have been validated. Total life cycle cost

Low-cost fabrication technologies for nanostructures: state-of-the-art and potential

International Nuclear Information System (INIS)

Santos, A; Deen, M J; Marsal, L F

2015-01-01

In the last decade, some low-cost nanofabrication technologies used in several disciplines of nanotechnology have demonstrated promising results in terms of versatility and scalability for producing innovative nanostructures. While conventional nanofabrication technologies such as photolithography are and will be an important part of nanofabrication, some low-cost nanofabrication technologies have demonstrated outstanding capabilities for large-scale production, providing high throughputs with acceptable resolution and broad versatility. Some of these nanotechnological approaches are reviewed in this article, providing information about the fundamentals, limitations and potential future developments towards nanofabrication processes capable of producing a broad range of nanostructures. Furthermore, in many cases, these low-cost nanofabrication approaches can be combined with traditional nanofabrication technologies. This combination is considered a promising way of generating innovative nanostructures suitable for a broad range of applications such as in opto-electronics, nano-electronics, photonics, sensing, biotechnology or medicine. (topical review)

Low-cost fabrication technologies for nanostructures: state-of-the-art and potential

Science.gov (United States)

Santos, A.; Deen, M. J.; Marsal, L. F.

2015-01-01

In the last decade, some low-cost nanofabrication technologies used in several disciplines of nanotechnology have demonstrated promising results in terms of versatility and scalability for producing innovative nanostructures. While conventional nanofabrication technologies such as photolithography are and will be an important part of nanofabrication, some low-cost nanofabrication technologies have demonstrated outstanding capabilities for large-scale production, providing high throughputs with acceptable resolution and broad versatility. Some of these nanotechnological approaches are reviewed in this article, providing information about the fundamentals, limitations and potential future developments towards nanofabrication processes capable of producing a broad range of nanostructures. Furthermore, in many cases, these low-cost nanofabrication approaches can be combined with traditional nanofabrication technologies. This combination is considered a promising way of generating innovative nanostructures suitable for a broad range of applications such as in opto-electronics, nano-electronics, photonics, sensing, biotechnology or medicine.

Low Cost, High Efficiency, High Pressure Hydrogen Storage

Energy Technology Data Exchange (ETDEWEB)

Mark Leavitt

2010-03-31

A technical and design evaluation was carried out to meet DOE hydrogen fuel targets for 2010. These targets consisted of a system gravimetric capacity of 2.0 kWh/kg, a system volumetric capacity of 1.5 kWh/L and a system cost of $4/kWh. In compressed hydrogen storage systems, the vast majority of the weight and volume is associated with the hydrogen storage tank. In order to meet gravimetric targets for compressed hydrogen tanks, 10,000 psi carbon resin composites were used to provide the high strength required as well as low weight. For the 10,000 psi tanks, carbon fiber is the largest portion of their cost. Quantum Technologies is a tier one hydrogen system supplier for automotive companies around the world. Over the course of the program Quantum focused on development of technology to allow the compressed hydrogen storage tank to meet DOE goals. At the start of the program in 2004 Quantum was supplying systems with a specific energy of 1.1-1.6 kWh/kg, a volumetric capacity of 1.3 kWh/L and a cost of $73/kWh. Based on the inequities between DOE targets and Quantum’s then current capabilities, focus was placed first on cost reduction and second on weight reduction. Both of these were to be accomplished without reduction of the fuel system’s performance or reliability. Three distinct areas were investigated; optimization of composite structures, development of “smart tanks” that could monitor health of tank thus allowing for lower design safety factor, and the development of “Cool Fuel” technology to allow higher density gas to be stored, thus allowing smaller/lower pressure tanks that would hold the required fuel supply. The second phase of the project deals with three additional distinct tasks focusing on composite structure optimization, liner optimization, and metal.

Cost estimate guidelines for advanced nuclear power technologies

International Nuclear Information System (INIS)

Hudson, C.R. II.

1986-07-01

To make comparative assessments of competing technologies, consistent ground rules must be applied when developing cost estimates. This document provides a uniform set of assumptions, ground rules, and requirements that can be used in developing cost estimates for advanced nuclear power technologies

Cost estimate guidelines for advanced nuclear power technologies

International Nuclear Information System (INIS)

Hudson, C.R. II.

1987-07-01

To make comparative assessments of competing technologies, consistent ground rules must be applied when developing cost estimates. This document provides a uniform set of assumptions, ground rules, and requirements that can be used in developing cost estimates for advanced nuclear power technologies

Development of Advanced Life Cycle Costing Methods for Technology Benefit/Cost/Risk Assessment

Science.gov (United States)

Yackovetsky, Robert (Technical Monitor)

2002-01-01

The overall objective of this three-year grant is to provide NASA Langley's System Analysis Branch with improved affordability tools and methods based on probabilistic cost assessment techniques. In order to accomplish this objective, the Aerospace Systems Design Laboratory (ASDL) needs to pursue more detailed affordability, technology impact, and risk prediction methods and to demonstrate them on variety of advanced commercial transports. The affordability assessment, which is a cornerstone of ASDL methods, relies on the Aircraft Life Cycle Cost Analysis (ALCCA) program originally developed by NASA Ames Research Center and enhanced by ASDL. This grant proposed to improve ALCCA in support of the project objective by updating the research, design, test, and evaluation cost module, as well as the engine development cost module. Investigations into enhancements to ALCCA include improved engine development cost, process based costing, supportability cost, and system reliability with airline loss of revenue for system downtime. A probabilistic, stand-alone version of ALCCA/FLOPS will also be developed under this grant in order to capture the uncertainty involved in technology assessments. FLOPS (FLight Optimization System program) is an aircraft synthesis and sizing code developed by NASA Langley Research Center. This probabilistic version of the coupled program will be used within a Technology Impact Forecasting (TIF) method to determine what types of technologies would have to be infused in a system in order to meet customer requirements. A probabilistic analysis of the CER's (cost estimating relationships) within ALCCA will also be carried out under this contract in order to gain some insight as to the most influential costs and the impact that code fidelity could have on future RDS (Robust Design Simulation) studies.

Cost optimisation studies of high power accelerators

Energy Technology Data Exchange (ETDEWEB)

McAdams, R.; Nightingale, M.P.S.; Godden, D. [AEA Technology, Oxon (United Kingdom)] [and others

1995-10-01

Cost optimisation studies are carried out for an accelerator based neutron source consisting of a series of linear accelerators. The characteristics of the lowest cost design for a given beam current and energy machine such as power and length are found to depend on the lifetime envisaged for it. For a fixed neutron yield it is preferable to have a low current, high energy machine. The benefits of superconducting technology are also investigated. A Separated Orbit Cyclotron (SOC) has the potential to reduce capital and operating costs and intial estimates for the transverse and longitudinal current limits of such machines are made.

Social costs of innovative electricity generation technologies in the present and in 2030

Energy Technology Data Exchange (ETDEWEB)

Preiss, Philipp; Friedrich, Rainer; Blesl, Markus; Wissel, Steffen; Mayer-Spohn, Oliver; Klotz, Volker [Stuttgart Univ. (DE). Inst. fuer Energiewirtschaft und Rationelle Energieanwendung (IER)

2008-07-01

Social costs (costs seen from the perspective of the society) differ from private costs and thus influence the ranking of electricity generating technologies. The resulting social costs data provide a basis for the recommendation to use the potential of nuclear, wind and hydropower as far as possible, however the potential of these technologies is limited. The analysis shows, that the remaining electricity demand in the future still should be met by using lignite and coal. Depending on the stringency of the climate change aims these plants would be equipped with CCS (carbon capture and storage) or not. Only with ambitious climate change aims and if CCS turns out to be less economically or technically feasible, than the import of electricity generated by a solar through systems in Mediterranean countries would become an option. The environmental advantages of PV are too small to compensate the very high investment costs in Germany. The detailed analysis of different contributions to the social costs per kWh shows that the costs of natural gas technologies are dominated by private costs of fuel supply. If we assume 50% higher prices than in the basic assumption this increases social costs up to 30%. (orig.)

Cost estimate guidelines for advanced nuclear power technologies

International Nuclear Information System (INIS)

Delene, J.G.; Hudson, C.R. II.

1990-03-01

To make comparative assessments of competing technologies, consistent ground rules must be applied when developing cost estimates. This document provides a uniform set of assumptions, ground rules, and requirements that can be used in developing cost estimates for advanced nuclear power technologies. 10 refs., 8 figs., 32 tabs

Controlling air pollution from passenger ferries: cost-effectiveness of seven technological options.

Science.gov (United States)

Farrell, Alexander E; Corbett, James J; Winebrake, James J

2002-12-01

Continued interest in improving air quality in the United States along with renewed interest in the expansion of urban passenger ferry service has created concern about air pollution from ferry vessels. This paper presents a methodology for estimating the air pollution emissions from passenger ferries and the costs of emissions control strategies. The methodology is used to estimate the emissions and costs of retrofitting or re-powering ferries with seven technological options (combinations of propulsion and emission control systems) onto three vessels currently in service in San Francisco Bay. The technologies include improved engine design, cleaner fuels (including natural gas), and exhaust gas cleanup devices. The three vessels span a range of ages and technologies, from a 25-year-old monohull to a modern, high-speed catamaran built only four years ago. By looking at a range of technologies, vessel designs, and service conditions, a sense of the broader implications of controlling emissions from passenger ferries across a range of vessels and service profiles is provided. Tier 2-certified engines are the most cost-effective choice, but all options are cost-effective relative to other emission control strategies already in place in the transportation system.

Low-cost interferometric TDM technology for dynamic sensing applications

Science.gov (United States)

Bush, Jeff; Cekorich, Allen

2004-12-01

A low-cost design approach for Time Division Multiplexed (TDM) fiber-optic interferometric interrogation of multi-channel sensor arrays is presented. This paper describes the evolutionary design process of the subject design. First, the requisite elements of interferometric interrogation are defined for a single channel sensor. The concept is then extended to multi-channel sensor interrogation implementing a TDM multiplex scheme where "traditional" design elements are utilized. The cost of the traditional TDM interrogator is investigated and concluded to be too high for entry into many markets. A new design approach is presented which significantly reduces the cost for TDM interrogation. This new approach, in accordance with the cost objectives, shows promise to bring this technology to within the threshold of commercial acceptance for a wide range of distributed fiber sensing applications.

Novel, low-cost alternative technologies to tackle practical, industrial conundrums – a case study of batteries

Directory of Open Access Journals (Sweden)

Chan Victor K. Y.

2016-01-01

Full Text Available Whereas batteries in comparison with most other means of energy storage are more environmentally friendly and economical in their operation, they are beset by low energy replenishment rates, low energy storage density, high capital cost of themselves, and high capital cost of energy replenishment infrastructures. Mainly based on ergonomics, this paper proposes a novel, low-cost alternative technology to practically and industrially make these weaknesses irrelevant to some extent without calling for revolutionary technological breakthroughs in material science, batteries’ microstructures, or battery manufacturing technologies. The technology takes advantage of modularization of battery systems, prioritization of charging and discharging of battery module(s according to ease of unloading and/or loading the battery module(s and/or ease of loading replacement battery module(s of the battery module(s.

Technology transfer by multinational firms: the resource cost of transferring technological know-how

Energy Technology Data Exchange (ETDEWEB)

Teece, D J

1977-06-01

The essence of modern economic growth is the increase in the stock of useful knowledge and the extension of its application. Since the origins of technical and social innovations have never been confined to the borders of any one nation, the economic growth of all countries depends to some degree on the successful application of a transnational stock of knowledge. Nevertheless, economists have been remarkably slow in addressing themselves to the economics of international technology transfer. This paper addresses itself to this need. The starting-point is Arrow's suggestion (Am. Econ. Review, 52: 29-35 (May 1969)) that the cost of communication, or information transfer, is a fundamental factor influencing the world-wide diffusion of technology. The purpose of the paper is to examine the level and determinants of the costs involved in transferring technology. The value of the resources that have to be utilized to accomplish the successful transfer of a given manufacturing technology is used as a measure of the cost of transfer. The resource cost concept is therefore designed to reflect the ease or difficulty of transferring technological know-how from manufacturing plants in one country to manufacturing plants in another. 32 references.

Cost decreases in environmental technology. Evidence from four case studies

Energy Technology Data Exchange (ETDEWEB)

Oosterhuis, F. [Instituut for Environmental Studies, Vrije Universiteit VU, Amsterdam (Netherlands)

2007-07-15

The cost of a new technology tends to decrease as its uptake grows, and environmental technology is no exception to this general rule. Factors that can bring about such cost reductions include economies of scale, 'learning-by-doing', incremental technological improvements, and growing competition. In preparing environmental policies, the potential for future cost reductions is often disregarded. The present study aims to provide some additional empirical evidence on the cost decreases in environmental technology and the factors that lie behind them. To this end, four exemplary case studies have been selected. The first case (NOx emission abatement by Selective Catalytic Reduction (SCR)), shows a wide variety in cost estimates, without a clear trend. This is even true for the costs of a fairly homogeneous type of investment (SCR in coal fired power plants). Nevertheless, it is clear that an important cost decrease has been achieved by prolonging the lifetime of the catalyst, which is one of the main cost components in SCR. In the second case (NH3 emission abatement by chemical air scrubbers in pig farming) there is not yet sufficient experience with the technology to draw conclusions on the development of costs. However, it is already clear that economizing on the capacity of the system can contribute to important cost savings. Three-way catalytic converters in cars have shown significant price decreases following their large scale introduction on the European market in the early 1990s. Probably economies of scale have played an important role in this case, as the size of the market made mass production possible. To some extent, cost reductions may also be attributed to improvements such as the need for less materials (e.g. platinum). Furthermore, the performance of catalytic converters has improved, implying that the cost per unit of emission reduction has decreased even more than the cost of the device itself. Market prices of Compact Fluorescent Lamps

Future Vehicle Technologies : high performance transportation innovations

Energy Technology Data Exchange (ETDEWEB)

Pratt, T. [Future Vehicle Technologies Inc., Maple Ridge, BC (Canada)

2010-07-01

Battery management systems (BMS) were discussed in this presentation, with particular reference to the basic BMS design considerations; safety; undisclosed information about BMS; the essence of BMS; and Future Vehicle Technologies' BMS solution. Basic BMS design considerations that were presented included the balancing methodology; prismatic/cylindrical cells; cell protection; accuracy; PCB design, size and components; communications protocol; cost of manufacture; and expandability. In terms of safety, the presentation addressed lithium fires; high voltage; high voltage ground detection; crash/rollover shutdown; complete pack shutdown capability; and heat shields, casings, and impact protection. BMS bus bar engineering considerations were discussed along with good chip design. It was concluded that FVTs advantage is a unique skillset in automotive technology and the development of speed and cost effectiveness. tabs., figs.

Low-Cost Bio-Based Carbon Fibers for High Temperature Processing

Energy Technology Data Exchange (ETDEWEB)

Paul, Ryan Michael [GrafTech International, Brooklyn Heights, OH (United States); Naskar, Amit [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-08-03

GrafTech International Holdings Inc. (GTI), under Award No. DE-EE0005779, worked with Oak Ridge National Laboratory (ORNL) under CRADA No. NFE-15-05807 to develop lignin-based carbon fiber (LBCF) technology and to demonstrate LBCF performance in high-temperature products and applications. This work was unique and different from other reported LBCF work in that this study was application-focused and scalability-focused. Accordingly, the executed work was based on meeting criteria based on technology development, cost, and application suitability. High-temperature carbon fiber based insulation is used in energy intensive industries, such as metal heat treating and ceramic and semiconductor material production. Insulation plays a critical role in achieving high thermal and process efficiency, which is directly related to energy usage, cost, and product competitiveness. Current high temperature insulation is made with petroleum based carbon fibers, and one goal of this protect was to develop and demonstrate an alternative lignin (biomass) based carbon fiber that would achieve lower cost, CO2 emissions, and energy consumption and result in insulation that met or exceeded the thermal efficiency of current commercial insulation. In addition, other products were targeted to be evaluated with LBCF. As the project was designed to proceed in stages, the initial focus of this work was to demonstrate lab-scale LBCF from at least 4 different lignin precursor feedstock sources that could meet the estimated production cost of $5.00/pound and have ash level of less than 500 ppm in the carbonized insulation-grade fiber. Accordingly, a preliminary cost model was developed based on publicly available information. The team demonstrated that 4 lignin samples met the cost criteria. In addition, the ash level for the 4 carbonized lignin samples was below 500 ppm. Processing as-received lignin to produce a high purity lignin fiber was a significant accomplishment in that most industrial

The impact of feedstock cost on technology selection and optimum size

International Nuclear Information System (INIS)

Cameron, Jay B.; Kumar, Amit; Flynn, Peter C.

2007-01-01

Development of biomass projects at optimum size and technology enhances the role that biomass can make in mitigating greenhouse gas. Optimum sized plants can be built when biomass resources are sufficient to meet feedstock demand; examples include wood and forest harvest residues from extensive forests, and grain straw and corn stover from large agricultural regions. The impact of feedstock cost on technology selection is evaluated by comparing the cost of power from the gasification and direct combustion of boreal forest wood chips. Optimum size is a function of plant cost and the distance variable cost (DVC, $ dry tonne -1 km -1 ) of the biomass fuel; distance fixed costs (DFC, $ dry tonne -1 ) such as acquisition, harvesting, loading and unloading do not impact optimum size. At low values of DVC and DFC, as occur with wood chips sourced from the boreal forest, direct combustion has a lower power cost than gasification. At higher values of DVC and DFC, gasification has a lower power cost than direct combustion. This crossover in most economic technology will always arise when a more efficient technology with a higher capital cost per unit of output is compared to a less efficient technology with a lower capital cost per unit of output. In such cases technology selection cannot be separated from an analysis of feedstock cost

Second Generation Novel High Temperature Commercial Receiver & Low Cost High Performance Mirror Collector for Parabolic Solar Trough

Energy Technology Data Exchange (ETDEWEB)

Stettenheim, Joel [Norwich Technologies, White River Junction, VT (United States)

2016-02-29

Norwich Technologies (NT) is developing a disruptively superior solar field for trough concentrating solar power (CSP). Troughs are the leading CSP technology (85% of installed capacity), being highly deployable and similar to photovoltaic (PV) systems for siting. NT has developed the SunTrap receiver, a disruptive alternative to vacuum-tube concentrating solar power (CSP) receivers, a market currently dominated by the Schott PTR-70. The SunTrap receiver will (1) operate at higher temperature (T) by using an insulated, recessed radiation-collection system to overcome the energy losses that plague vacuum-tube receivers at high T, (2) decrease acquisition costs via simpler structure, and (3) dramatically increase reliability by eliminating vacuum. It offers comparable optical efficiency with thermal loss reduction from ≥ 26% (at presently standard T) to ≥ 55% (at high T), lower acquisition costs, and near-zero O&M costs.

Technology Estimating 2: A Process to Determine the Cost and Schedule of Space Technology Research and Development

Science.gov (United States)

Cole, Stuart K.; Wallace, Jon; Schaffer, Mark; May, M. Scott; Greenberg, Marc W.

2014-01-01

As a leader in space technology research and development, NASA is continuing in the development of the Technology Estimating process, initiated in 2012, for estimating the cost and schedule of low maturity technology research and development, where the Technology Readiness Level is less than TRL 6. NASA' s Technology Roadmap areas consist of 14 technology areas. The focus of this continuing Technology Estimating effort included four Technology Areas (TA): TA3 Space Power and Energy Storage, TA4 Robotics, TA8 Instruments, and TA12 Materials, to confine the research to the most abundant data pool. This research report continues the development of technology estimating efforts completed during 2013-2014, and addresses the refinement of parameters selected and recommended for use in the estimating process, where the parameters developed are applicable to Cost Estimating Relationships (CERs) used in the parametric cost estimating analysis. This research addresses the architecture for administration of the Technology Cost and Scheduling Estimating tool, the parameters suggested for computer software adjunct to any technology area, and the identification of gaps in the Technology Estimating process.

Innovation in technology for the least product price and cost - a new minimum cost relation for reductions during technological learning

International Nuclear Information System (INIS)

Duffey, R.B.

2004-01-01

By analogy with the concepts of human learning, we show and introduce a new method to obtain least product cost and price that includes the effect of innovation and technological learning in manufacturing and production. This key result is a new paradigm instead of the usual economic 'power law' formulation. The new analysis is based on extensive analysis of many technological systems, and is directly related to the presence of learning as experience is accumulated. The results agree with the observed data. By using a consistent basis, the method replaces previous empirical 'power law' descriptions of the technological learning curve with a new 'marginal minimum cost equation' (MCE). (author)

Technology learning for fuel cells. An assessment of past and potential cost reductions

International Nuclear Information System (INIS)

Schoots, K.; Van der Zwaan, B.C.C.; Kramer, G.J.

2010-01-01

Fuel cells have gained considerable interest as a means to efficiently convert the energy stored in gases like hydrogen and methane into electricity. Further developing fuel cells in order to reach cost, safety and reliability levels at which their widespread use becomes feasible is an essential prerequisite for the potential establishment of a 'hydrogen economy'. A major factor currently obviating the extensive use of fuel cells is their relatively high costs. At present we estimate these at about 1100 EUR(2005)W for an 80 kW fuel cell system but notice that specific costs vary markedly with fuel cell system power capacity. We analyze past fuel cell cost reductions for both individual manufacturers and the global market. We determine learning curves, with fairly high uncertainty ranges, for three different types of fuel cell technology - AFC, PAFC and PEMFC - each manufactured by a different producer. For PEMFC technology we also calculate a global learning curve, characterised by a learning rate of 21% with an error margin of 4%. Given their respective uncertainties, this global learning rate value is in agreement with those we find for different manufacturers. In contrast to some other new energy technologies, R and D still plays a major role in today's fuel cell improvement process and hence probably explains a substantial part of our observed cost reductions. The remaining share of these cost reductions derives from learning-by-doing proper. Since learning-by-doing usually involves a learning rate of typically 20%, the residual value for pure learning we find for fuel cells is relatively low. In an ideal scenario for fuel cell technology we estimate a bottom-line for specific (80 kW system) manufacturing costs of 95 EUR(2005)W. Although learning curves observed in the past constitute no guarantee for sustained cost reductions in the future, when we assume global total learning at the pace calculated here as the only cost reduction mechanism, this ultimate cost

Cost escalation in health - care technology possible solutions | Járos ...

African Journals Online (AJOL)

Solutions to cost escalation due to health-care technology are proposed. It is argued that proper systems analysis, technology assessment, and planning would result in net savings and itnproved cost-benefits. Identification of needs early in the technological life cycle can positively influence the final form of the chosen ...

Cost-benefit calculation of phytoremediation technology for heavy-metal-contaminated soil.

Science.gov (United States)

Wan, Xiaoming; Lei, Mei; Chen, Tongbin

2016-09-01

Heavy-metal pollution of soil is a serious issue worldwide, particularly in China. Soil remediation is one of the most difficult management issues for municipal and state agencies because of its high cost. A two-year phytoremediation project for soil contaminated with arsenic, cadmium, and lead was implemented to determine the essential parameters for soil remediation. Results showed highly efficient heavy metal removal. Costs and benefits of this project were calculated. The total cost of phytoremediation was US$75,375.2/hm(2) or US$37.7/m(3), with initial capital and operational costs accounting for 46.02% and 53.98%, respectively. The costs of infrastructures (i.e., roads, bridges, and culverts) and fertilizer were the highest, mainly because of slow economic development and serious contamination. The cost of phytoremediation was lower than the reported values of other remediation technologies. Improving the mechanization level of phytoremediation and accurately predicting or preventing unforeseen situations were suggested for further cost reduction. Considering the loss caused by environmental pollution, the benefits of phytoremediation will offset the project costs in less than seven years. Copyright © 2015 Elsevier B.V. All rights reserved.

Heat savings and heat generation technologies: Modelling of residential investment behaviour with local health costs

International Nuclear Information System (INIS)

Zvingilaite, Erika; Klinge Jacobsen, Henrik

2015-01-01

The trade-off between investing in energy savings and investing in individual heating technologies with high investment and low variable costs in single family houses is modelled for a number of building and consumer categories in Denmark. For each group the private economic cost of providing heating comfort is minimised. The private solution may deviate from the socio-economical optimal solution and we suggest changes to policy to incentivise the individuals to make choices more in line with the socio-economic optimal mix of energy savings and technologies. The households can combine their primary heating source with secondary heating e.g. a woodstove. This choice results in increased indoor air pollution with fine particles causing health effects. We integrate health cost due to use of woodstoves into household optimisation of heating expenditures. The results show that due to a combination of low costs of primary fuel and low environmental performance of woodstoves today, included health costs lead to decreased use of secondary heating. Overall the interdependence of heat generation technology- and heat saving-choice is significant. The total optimal level of heat savings for private consumers decrease by 66% when all have the option to shift to the technology with lowest variable costs. - Highlights: • Heat saving investment and heat technology choice are interdependent. • Health damage costs should be included in private heating choice optimisation. • Flexibility in heating technology choice reduce the optimal level of saving investments. • Models of private and socioeconomic optimal heating produce different technology mix. • Rebound effects are moderate but varies greatly among consumer categories

Efficiency and cost advantages of an advanced-technology nuclear electrolytic hydrogen-energy production facility

Science.gov (United States)

Donakowski, T. D.; Escher, W. J. D.; Gregory, D. P.

1977-01-01

The concept of an advanced-technology (viz., 1985 technology) nuclear-electrolytic water electrolysis facility was assessed for hydrogen production cost and efficiency expectations. The facility integrates (1) a high-temperature gas-cooled nuclear reactor (HTGR) operating a binary work cycle, (2) direct-current (d-c) electricity generation via acyclic generators, and (3) high-current-density, high-pressure electrolyzers using a solid polymer electrolyte (SPE). All subsystems are close-coupled and optimally interfaced for hydrogen production alone (i.e., without separate production of electrical power). Pipeline-pressure hydrogen and oxygen are produced at 6900 kPa (1000 psi). We found that this advanced facility would produce hydrogen at costs that were approximately half those associated with contemporary-technology nuclear electrolysis: $5.36 versus $10.86/million Btu, respectively. The nuclear-heat-to-hydrogen-energy conversion efficiency for the advanced system was estimated as 43%, versus 25% for the contemporary system.

Integrated thermal and nonthermal treatment technology and subsystem cost sensitivity analysis

International Nuclear Information System (INIS)

Harvego, L.A.; Schafer, J.J.

1997-02-01

The U.S. Department of Energy's (DOE) Environmental Management Office of Science and Technology (EM-50) authorized studies on alternative systems for treating contact-handled DOE mixed low-level radioactive waste (MLLW). The on-going Integrated Thermal Treatment Systems' (ITTS) and the Integrated Nonthermal Treatment Systems' (INTS) studies satisfy this request. EM-50 further authorized supporting studies including this technology and subsystem cost sensitivity analysis. This analysis identifies areas where technology development could have the greatest impact on total life cycle system costs. These areas are determined by evaluating the sensitivity of system life cycle costs relative to changes in life cycle component or phase costs, subsystem costs, contingency allowance, facility capacity, operating life, and disposal costs. For all treatment systems, the most cost sensitive life cycle phase is the operations and maintenance phase and the most cost sensitive subsystem is the receiving and inspection/preparation subsystem. These conclusions were unchanged when the sensitivity analysis was repeated on a present value basis. Opportunity exists for technology development to reduce waste receiving and inspection/preparation costs by effectively minimizing labor costs, the major cost driver, within the maintenance and operations phase of the life cycle

Annual meeting on nuclear technology '96. Technical session: Energy costs

International Nuclear Information System (INIS)

1996-08-01

The two papers of this session deal with the costs of two different energy generation systems, one is based on photovoltaic energy conversion, and the other is the nuclear fuel cycle and nuclear energy generation. The author shows that the costs of these two energy systems in Germany are much more governed by decisions taken in the political domain than is the case in other countries. Although German science and technology in these two engineering fields hold a top rank worldwide, the high costs that seem inevitable in Germany are expected to be a major reason why the photovoltaic industry will have to leave the country and go abroad to exploit the better chances there. (DG) [de

Cost-efficient demand-pull policies for multi-purpose technologies – The case of stationary electricity storage

International Nuclear Information System (INIS)

Battke, Benedikt; Schmidt, Tobias S.

2015-01-01

Highlights: • A definition of multi-purpose technologies (MPTs) is proposed. • Opportunities for a cost-efficient demand-pull policy strategy for MPTs are derived. • The multi-purpose character of stationary electricity storage (SES) is shown. • An exemplary profitability assessment of one SES technology supports the argument. - Abstract: Stationary electricity storage technologies (SES) allow to increase the shares of intermittent renewable energy technologies in electricity networks. As SES currently exhibit high costs, policy makers have started introducing demand-pull policies in order to foster their diffusion and drive these technologies further down the learning curve. However, as observed in the case of renewable energy technologies, demand-pull policies for technologies can come at high costs in cases where the profitability gap that needs to be covered by the policy support is large. Yet, SES can create value in multiple distinct applications in the power system – making it a “multi-purpose technology”. We argue that policy makers can make use of the multi-purpose character of SES to limit costs of demand-pull policies. We propose a policy strategy which grants support based on the profitability gap in the different applications, thereby moving down the learning curve efficiently. To support our argumentation, we firstly conduct a comprehensive literature review of SES applications exemplifying the multi-purpose character of these technologies. Second, we assess the profitability of one SES technology (vanadium redox flow battery) in five SES applications, highlighting a strong variation of the profitability gap across these applications

Fundamental understanding and development of low-cost, high-efficiency silicon solar cells

Energy Technology Data Exchange (ETDEWEB)

ROHATGI,A.; NARASIMHA,S.; MOSCHER,J.; EBONG,A.; KAMRA,S.; KRYGOWSKI,T.; DOSHI,P.; RISTOW,A.; YELUNDUR,V.; RUBY,DOUGLAS S.

2000-05-01

The overall objectives of this program are (1) to develop rapid and low-cost processes for manufacturing that can improve yield, throughput, and performance of silicon photovoltaic devices, (2) to design and fabricate high-efficiency solar cells on promising low-cost materials, and (3) to improve the fundamental understanding of advanced photovoltaic devices. Several rapid and potentially low-cost technologies are described in this report that were developed and applied toward the fabrication of high-efficiency silicon solar cells.

Standard semiconductor packaging for high-reliability low-cost MEMS applications

Science.gov (United States)

Harney, Kieran P.

2005-01-01

Microelectronic packaging technology has evolved over the years in response to the needs of IC technology. The fundamental purpose of the package is to provide protection for the silicon chip and to provide electrical connection to the circuit board. Major change has been witnessed in packaging and today wafer level packaging technology has further revolutionized the industry. MEMS (Micro Electro Mechanical Systems) technology has created new challenges for packaging that do not exist in standard ICs. However, the fundamental objective of MEMS packaging is the same as traditional ICs, the low cost and reliable presentation of the MEMS chip to the next level interconnect. Inertial MEMS is one of the best examples of the successful commercialization of MEMS technology. The adoption of MEMS accelerometers for automotive airbag applications has created a high volume market that demands the highest reliability at low cost. The suppliers to these markets have responded by exploiting standard semiconductor packaging infrastructures. However, there are special packaging needs for MEMS that cannot be ignored. New applications for inertial MEMS devices are emerging in the consumer space that adds the imperative of small size to the need for reliability and low cost. These trends are not unique to MEMS accelerometers. For any MEMS technology to be successful the packaging must provide the basic reliability and interconnection functions, adding the least possible cost to the product. This paper will discuss the evolution of MEMS packaging in the accelerometer industry and identify the main issues that needed to be addressed to enable the successful commercialization of the technology in the automotive and consumer markets.

CENET: Cost Efficiency in a New Era with new Technology

Energy Technology Data Exchange (ETDEWEB)

Karlsen, Jan E.; Lund, Bjoernar; Bos, Christian F.M.; Stokka, Sigmund

1997-12-31

This report relates to the CENET (Cost Efficiency in a New Era with new Technology) project the oil and gas in Europe. Key objectives of the CENET project are to determine the role of RTD (Research and Technology Development) in European oil and gas industry towards improved value and cost reduction with a particular focus on the means of developing offshore European marginal fields commercially, to identify RTD areas with the largest potential for improved value and cost reduction and technological developments and advances which are likely to increase European competitiveness internationally, and to provide guidance to European governments when deciding RTD priorities. A new era with new technology concerns increased oil and gas potential during the next century, a new era with clean, safe and cost efficient energy production, a new era with a new business structure, and globalization of the industry. 44 tabs., 5 figs., 23 tabs.

Pipeline cost reduction through effective project management and applied technology

Energy Technology Data Exchange (ETDEWEB)

Jenkins, A. [TransCanada Pipeline Ltd., Alberta (Canada); Babuk, T. [Empress International Inc., Westwood, NJ (United States); Mohitpour, M. [Tempsys Pipeline Solutions Inc., Vancouver, BC (Canada); Murray, M.A. [National Energy Board of Canada (Canada)

2005-07-01

Pipelines are regarded by many as passive structures with the technology involved in their construction and operation being viewed as relatively simple and stable. If such is the case how can there be much room for cost improvement? In reality, there have been many technological and regulatory innovations required within the pipeline industry to meet the challenges posed by ever increasing consumer demand for hydrocarbons, the effects of aging infrastructure and a need to control operating and maintenance expenditures. The importance of technology management, as a subset of overall project management, is a key element of life cycle cost control. Assurance of public safety and the integrity of the system are other key elements in ensuring a successful pipeline project. The essentials of best practise project management from an owner/ operator's perspective are set out in the paper. Particular attention is paid to the appropriate introduction of new technology, strategic procurement practice and material selection, indicating that capital cost savings of up to 15% are achievable without harming life cycle cost. The value of partnering leading to technical innovation, cost savings and improved profitability for all the participants is described. Partnering also helps avoid duplicated effort through the use of common tools for design, planning schedule tracking and reporting. Investing in appropriate technology development has been a major source of cost reduction in recent years and the impact of a number of these recently introduced technologies in the areas of materials, construction processes and operation and maintenance are discussed in the paper. (author)

A methodology for spacecraft technology insertion analysis balancing benefit, cost, and risk

Science.gov (United States)

Bearden, David Allen

Emerging technologies are changing the way space missions are developed and implemented. Technology development programs are proceeding with the goal of enhancing spacecraft performance and reducing mass and cost. However, it is often the case that technology insertion assessment activities, in the interest of maximizing performance and/or mass reduction, do not consider synergistic system-level effects. Furthermore, even though technical risks are often identified as a large cost and schedule driver, many design processes ignore effects of cost and schedule uncertainty. This research is based on the hypothesis that technology selection is a problem of balancing interrelated (and potentially competing) objectives. Current spacecraft technology selection approaches are summarized, and a Methodology for Evaluating and Ranking Insertion of Technology (MERIT) that expands on these practices to attack otherwise unsolved problems is demonstrated. MERIT combines the modern techniques of technology maturity measures, parametric models, genetic algorithms, and risk assessment (cost and schedule) in a unique manner to resolve very difficult issues including: user-generated uncertainty, relationships between cost/schedule and complexity, and technology "portfolio" management. While the methodology is sufficiently generic that it may in theory be applied to a number of technology insertion problems, this research focuses on application to the specific case of small (<500 kg) satellite design. Small satellite missions are of particular interest because they are often developed under rigid programmatic (cost and schedule) constraints and are motivated to introduce advanced technologies into the design. MERIT is demonstrated for programs procured under varying conditions and constraints such as stringent performance goals, not-to-exceed costs, or hard schedule requirements. MERIT'S contributions to the engineering community are its: unique coupling of the aspects of performance

A standard methodology for cost-effectiveness analysis of new environmental technologies

International Nuclear Information System (INIS)

Booth, S.R.; Trocki, L.K.; Bowling, L.

1994-01-01

This paper outlines a methodology that is being applied to assess the cost-effectiveness of new environmental technologies under development by EM-50, DOE. Performance, total system effects, and life-cycle costs are all considered in the methodology to compare new technologies with existing or base-line technologies. An example of performance characterization is given in the paper. Sources of data for cost estimates and technology characterizations also appear in the paper. The Department of Energy (DOE) is facing a massive clean up effort of waste sites that contain hazardous, radioactive, or mixed materials. DOE has recognized that improvements in environmental restoration and waste management methods can potentially save the taxpayers billions of dollars as older, less-effective technologies are displaced. Consequently, DOE has targeted significant funding to search for new technologies and to test and demonstrate them in rapid and cost-effective manner with the goal of applying them quickly to address environmental problems

Cost of New Technologies in Prostate Cancer Treatment: Systematic Review of Costs and Cost Effectiveness of Robotic-assisted Laparoscopic Prostatectomy, Intensity-modulated Radiotherapy, and Proton Beam Therapy.

Science.gov (United States)

Schroeck, Florian Rudolf; Jacobs, Bruce L; Bhayani, Sam B; Nguyen, Paul L; Penson, David; Hu, Jim

2017-11-01

Some of the high costs of robot-assisted radical prostatectomy (RARP), intensity-modulated radiotherapy (IMRT), and proton beam therapy may be offset by better outcomes or less resource use during the treatment episode. To systematically review the literature to identify the key economic trade-offs implicit in a particular treatment choice for prostate cancer. We systematically reviewed the literature according to the Preferred Reporting Items for Systematic Reviews and Meta-analyses (PRISMA) statement and protocol. We searched Medline, Embase, and Web of Science for articles published between January 2001 and July 2016, which compared the treatment costs of RARP, IMRT, or proton beam therapy to the standard treatment. We identified 37, nine, and three studies, respectively. RARP is costlier than radical retropubic prostatectomy for hospitals and payers. However, RARP has the potential for a moderate cost advantage for payers and society over a longer time horizon when optimal cancer and quality-of-life outcomes are achieved. IMRT is more expensive from a payer's perspective compared with three-dimensional conformal radiotherapy, but also more cost effective when defined by an incremental cost effectiveness ratio new versus traditional technologies is costlier. However, given the low quality of evidence and the inconsistencies across studies, the precise difference in costs remains unclear. Attempts to estimate whether this increased cost is worth the expense are hampered by the uncertainty surrounding improvements in outcomes, such as cancer control and side effects of treatment. If the new technologies can consistently achieve better outcomes, then they may be cost effective. We review the cost and cost effectiveness of robot-assisted radical prostatectomy, intensity-modulated radiotherapy, and proton beam therapy in prostate cancer treatment. These technologies are costlier than their traditional counterparts. It remains unclear whether their use is associated

Cost effectiveness studies of environmental technologies: Volume 1

International Nuclear Information System (INIS)

Silva, E.M.; Booth, S.R.

1994-02-01

This paper examines cost effectiveness studies of environmental technologies including the following: (1) In Situ Air Stripping, (2) Surface Towed Ordinance Locator System, (3) Ditch Witch Horizontal Boring Technology, (4) Direct Sampling Ion Trap Mass Spectrometer, (5) In Situ Vitrification, (6) Site Characterization and Analysis Penetrometer System, (7) In Situ Bioremediation, and (8) SEAMIST Membrane System Technology

Lower cost air measurement technology – what is on the ...

Science.gov (United States)

This presentation is to the MARAMA 2014 annual monitoring meeting and is an invited talk to provide an overview on lower cost air measurement technology. This presentation is to the MARAMA 2014 annual monitoring meeting and is an invited talk to provide an overview on lower cost air measurement technology.

Innovation in Nuclear Technology for the Least Product Price and Cost

International Nuclear Information System (INIS)

Duffey, Romney

2003-01-01

In energy markets, costs dominate for all new technology introductions (pressure valves, gas turbines, reactors) both now and far into the future. Technology improves, and costs are reduced as markets are penetrated with the trend following a learning/experience curve (MCE) based on classic economic forces. The curve followed is governed by development costs and market targets, and nuclear systems follow such a curve in order to compete with other technologies and projected future cost for alternate energy initiatives. Funding impacts directly on market penetration and on the ''learning rate.'' The CANDU/AECL development path (experience curve) is a chosen balance between evolution and revolution for a competitive advantage

A new principle for low-cost hydrogen sensors for fuel cell technology safety

Energy Technology Data Exchange (ETDEWEB)

Liess, Martin [Rhein Main University of Applied Sciences, Rüsselsheim, Wiesbaden (Germany)

2014-03-24

Hydrogen sensors are of paramount importance for the safety of hydrogen fuel cell technology as result of the high pressure necessary in fuel tanks and its low explosion limit. I present a novel sensor principle based on thermal conduction that is very sensitive to hydrogen, highly specific and can operate on low temperatures. As opposed to other thermal sensors it can be operated with low cost and low power driving electronics. On top of this, as sensor element a modified standard of-the shelf MEMS thermopile IR-sensor can be used. The sensor principle presented is thus suited for the future mass markets of hydrogen fuel cell technology.S.

Pebble bed modular reactors versus other generation technologies. Costs and challenges for South Africa

International Nuclear Information System (INIS)

Grubert, Emily; Parks, Brian; Schneider, Erich; Sekar, Srinivas

2011-01-01

South Africa is Africa's major economy, with plans to double its electricity generation capacity by 2026. South Africa has spent almost two decades developing a nuclear reactor known as a Pebble Bed Modular Reactor (PBMR), which could provide substantial benefits to the electricity grid but was recently mothballed due to high costs. This work estimates the lifecycle financial costs of South African PBMRs, then compares these costs to those of five other generation options: coal, nuclear as pressurized water reactors (PWRs), wind, and solar as photovoltaics (PV) or concentrating solar power (CSP). Each technology is evaluated with low, base case, and high assumptions for capital costs, construction time, and interest rates. Decommissioning costs, project lifetime, capacity factors, and sensitivity to carbon price are also considered. PBMR could be cost competitive with coal under certain low cost conditions, even without a carbon price. However, international lending practices and other factors suggest that a high capital cost, high interest rate nuclear plant is likely to be competing with a low capital cost, low interest rate coal plant in a market where cost recovery is challenging. PBMR could potentially become more competitive if low rate international loans were available to nuclear projects or became unavailable to coal projects. (author)

Longitudinal analysis of high-technology medical services and hospital financial performance.

Science.gov (United States)

Zengul, Ferhat D; Weech-Maldonado, Robert; Ozaydin, Bunyamin; Patrician, Patricia A; OʼConnor, Stephen J

U.S. hospitals have been investing in high-technology medical services as a strategy to improve financial performance. Despite the interest in high-tech medical services, there is not much information available about the impact of high-tech services on financial performance. The aim of this study was to examine the impact of high-tech medical services on financial performance of U.S. hospitals by using the resource-based view of the firm as a conceptual framework. Fixed-effects regressions with 2 years lagged independent variables using a longitudinal panel sample of 3,268 hospitals (2005-2010). It was hypothesized that hospitals with rare or large numbers (breadth) of high-tech medical services will experience better financial performance. Fixed effects regression results supported the link between a larger breadth of high-tech services and total margin, but only among not-for-profit hospitals. Both breadth and rareness of high-tech services were associated with high total margin among not-for-profit hospitals. Neither breadth nor rareness of high-tech services was associated with operating margin. Although breadth and rareness of high-tech services resulted in lower expenses per inpatient day among not-for-profit hospitals, these lower costs were offset by lower revenues per inpatient day. Enhancing the breadth of high-tech services may be a legitimate organizational strategy to improve financial performance, especially among not-for-profit hospitals. Hospitals may experience increased productivity and efficiency, and therefore lower inpatient operating costs, as a result of newer technologies. However, the negative impact on operating revenue should caution hospital administrators about revenue reducing features of these technologies, which may be related to the payer mix that these technologies may attract. Therefore, managers should consider both the cost and revenue implications of these technologies.

Minimizing the cost of subsea developments through technological innovation

International Nuclear Information System (INIS)

Eyre, G.; Loth, B.

1994-01-01

The paper summarizes the results of an extensive study carried out for the UK Government. This assessed the cost and economic impact of technological innovation on subsea and floating developments in the UKCS. The study covered, innovations that could be applied to subsea developments to significantly reduce cost, including multiwell completions, composite pipelines, compartmented pipelines, pipeline specification breaking and autonomous control systems. Cost and economic models were used to assess the economic impact of technological innovation on marginal field developments. The results of these assessments were drawn up as a series of ranking lists designed to assist manufacturers and suppliers in establishing priorities for research and development funding. The study also explored the potential UKCS and World market for innovative subsea technologies and quantified the research and development required to bring key innovations into commercial use

[Cost of assisted reproduction technology in a public hospital].

Science.gov (United States)

Navarro Espigares, José Luis; Martínez Navarro, Luis; Castilla Alcalá, José Antonio; Hernández Torres, Elisa

2006-01-01

Most studies on the costs of assisted reproductive technologies (ART) identify the total cost of the procedure with the direct cost, without considering important items such as overhead or intermediate costs. The objective of this study was to determine the cost per ART procedure in a public hospital in 2003 and to compare the results with those in the same hospital in 1998. Data from the Human Reproduction Unit of the Virgen de las Nieves University Hospital in Granada (Spain) from 1998 and 2003 were analyzed. Since the total costs of the unit were known, the cost of the distinct ART procedures performed in the hospital was calculated by means of a methodology for cost distribution. Between 1998 and 2003, the activity and costs of the Human Reproduction Unit analyzed evolved differently. Analysis of activity showed that some techniques, such as intracytoplasmic sperm injection, were consolidated while others, such as stimulation without assisted reproduction or intracervical insemination were abandoned. In all procedures, unit costs per cycle and per delivery decreased in the period analyzed. Important changes took place in the structure of costs of ART in the Human Reproduction Unit of the Virgen de las Nieves University Hospital between 1998 and 2003. Some techniques were discontinued, while others gained importance. Technological advances and structural innovations, together with a "learning effect," modified the structure of ART-related costs.

The differential impact of low-carbon technologies on climate change mitigation cost under a range of socioeconomic and climate policy scenarios

International Nuclear Information System (INIS)

Barron, Robert; McJeon, Haewon

2015-01-01

This paper considers the effect of several key parameters of low carbon energy technologies on the cost of abatement. A methodology for determining the minimum level of performance required for a parameter to have a statistically significant impact on CO 2 abatement cost is developed and used to evaluate the impact of eight key parameters of low carbon energy supply technologies on the cost of CO 2 abatement. The capital cost of nuclear technology is found to have the greatest impact of the parameters studied. The cost of biomass and CCS technologies also have impacts, while their efficiencies have little, if any. Sensitivity analysis of the results with respect to population, GDP, and CO 2 emission constraint show that the minimum performance level and impact of nuclear technologies is consistent across the socioeconomic scenarios studied, while the other technology parameters show different performance under higher population, lower GDP scenarios. Solar technology was found to have a small impact, and then only at very low costs. These results indicate that the cost of nuclear is the single most important driver of abatement cost, and that trading efficiency for cost may make biomass and CCS technologies more competitive. - Highlights: • The impact of low carbon energy technology on abatement cost is considered. • Nuclear has the largest impact among technologies considered. • Cost has higher impact than efficiency for biomass technologies. • Biomass technologies generally have larger impacts than carbon capture. • Biomass technologies are more valuable in low GDP, high population scenarios

Solar thermal technology development: Estimated market size and energy cost savings. Volume 2: Assumptions, methodology and results

Science.gov (United States)

Gates, W. R.

1983-02-01

Estimated future energy cost savings associated with the development of cost-competitive solar thermal technologies (STT) are discussed. Analysis is restricted to STT in electric applications for 16 high-insolation/high-energy-price states. Three fuel price scenarios and three 1990 STT system costs are considered, reflecting uncertainty over future fuel prices and STT cost projections. Solar thermal technology research and development (R&D) is found to be unacceptably risky for private industry in the absence of federal support. Energy cost savings were projected to range from $0 to $10 billion (1990 values in 1981 dollars), depending on the system cost and fuel price scenario. Normal R&D investment risks are accentuated because the Organization of Petroleum Exporting Countries (OPEC) cartel can artificially manipulate oil prices and undercut growth of alternative energy sources. Federal participation in STT R&D to help capture the potential benefits of developing cost-competitive STT was found to be in the national interest. Analysis is also provided regarding two federal incentives currently in use: The Federal Business Energy Tax Credit and direct R&D funding.

Solar thermal technology development: Estimated market size and energy cost savings. Volume 2: Assumptions, methodology and results

Science.gov (United States)

Gates, W. R.

1983-01-01

Estimated future energy cost savings associated with the development of cost-competitive solar thermal technologies (STT) are discussed. Analysis is restricted to STT in electric applications for 16 high-insolation/high-energy-price states. Three fuel price scenarios and three 1990 STT system costs are considered, reflecting uncertainty over future fuel prices and STT cost projections. Solar thermal technology research and development (R&D) is found to be unacceptably risky for private industry in the absence of federal support. Energy cost savings were projected to range from $0 to $10 billion (1990 values in 1981 dollars), depending on the system cost and fuel price scenario. Normal R&D investment risks are accentuated because the Organization of Petroleum Exporting Countries (OPEC) cartel can artificially manipulate oil prices and undercut growth of alternative energy sources. Federal participation in STT R&D to help capture the potential benefits of developing cost-competitive STT was found to be in the national interest. Analysis is also provided regarding two federal incentives currently in use: The Federal Business Energy Tax Credit and direct R&D funding.

Transaction costs and technological development: The case of the Danish fruit and vegetable industry

DEFF Research Database (Denmark)

Foss, Kirsten

1996-01-01

It is argued that technological change can be understood in terms of attempts to reduce transaction costs as well as production costs. Two types of paths of technological development are identified: a production cost minimizing path, and a transac cost minimizing path. The creation of new...... technological opportunites underlying the path of production-cost.minimizing depends on the emergence of problems of optimizing the performance of products and processing technology. The exploitation of su opportunities may easily be interpreted within a production perspective since the economic consequences...... would be reduced production costs. The creation of new technological opportunities within the transaction-costs-minimizing path depends on th continual emergence of problems related to the control of variablility in product quality or performance. The economic consequence from exploiting...

Integrating sequencing technologies in personal genomics: optimal low cost reconstruction of structural variants.

Directory of Open Access Journals (Sweden)

Jiang Du

2009-07-01

Full Text Available The goal of human genome re-sequencing is obtaining an accurate assembly of an individual's genome. Recently, there has been great excitement in the development of many technologies for this (e.g. medium and short read sequencing from companies such as 454 and SOLiD, and high-density oligo-arrays from Affymetrix and NimbelGen, with even more expected to appear. The costs and sensitivities of these technologies differ considerably from each other. As an important goal of personal genomics is to reduce the cost of re-sequencing to an affordable point, it is worthwhile to consider optimally integrating technologies. Here, we build a simulation toolbox that will help us optimally combine different technologies for genome re-sequencing, especially in reconstructing large structural variants (SVs. SV reconstruction is considered the most challenging step in human genome re-sequencing. (It is sometimes even harder than de novo assembly of small genomes because of the duplications and repetitive sequences in the human genome. To this end, we formulate canonical problems that are representative of issues in reconstruction and are of small enough scale to be computationally tractable and simulatable. Using semi-realistic simulations, we show how we can combine different technologies to optimally solve the assembly at low cost. With mapability maps, our simulations efficiently handle the inhomogeneous repeat-containing structure of the human genome and the computational complexity of practical assembly algorithms. They quantitatively show how combining different read lengths is more cost-effective than using one length, how an optimal mixed sequencing strategy for reconstructing large novel SVs usually also gives accurate detection of SNPs/indels, how paired-end reads can improve reconstruction efficiency, and how adding in arrays is more efficient than just sequencing for disentangling some complex SVs. Our strategy should facilitate the sequencing of

Interim monitoring of cost dynamics for publicly supported energy technologies

Energy Technology Data Exchange (ETDEWEB)

Nemet, Gregory F. [La Follette School of Public Affairs, University of Wisconsin, 1225 Observatory Drive, Madison, WI 53706 (United States)]|[Nelson Institute for Environmental Studies, University of Wisconsin, Madison, WI 53726 (United States)

2009-03-15

The combination of substantial public funding of nascent energy technologies and recent increases in the costs of those that have been most heavily supported has raised questions about whether policy makers should sustain, alter, enhance, or terminate such programs. This paper uses experience curves for photovoltaics (PV) and wind to (1) estimate ranges of costs for these public programs and (2) introduce new ways of evaluating recent cost dynamics. For both technology cases, the estimated costs of the subsidies required to reach targets are sensitive to the choice of time period on which cost projections are based. The variation in the discounted social cost of subsidies exceeds an order of magnitude. Vigilance is required to avoid the very expensive outcomes contained within these distributions of social costs. Two measures of the significance of recent deviations are introduced. Both indicate that wind costs are within the expected range of prior forecasts but that PV costs are not. The magnitude of the public funds involved in these programs heightens the need for better analytical tools with which to monitor and evaluate cost dynamics. (author)

Demand Response Advanced Controls Framework and Assessment of Enabling Technology Costs

Energy Technology Data Exchange (ETDEWEB)

Potter, Jennifer; Cappers, Peter

2017-08-28

The Demand Response Advanced Controls Framework and Assessment of Enabling Technology Costs research describe a variety of DR opportunities and the various bulk power system services they can provide. The bulk power system services are mapped to a generalized taxonomy of DR “service types”, which allows us to discuss DR opportunities and bulk power system services in fewer yet broader categories that share similar technological requirements which mainly drive DR enablement costs. The research presents a framework for the costs to automate DR and provides descriptions of the various elements that drive enablement costs. The report introduces the various DR enabling technologies and end-uses, identifies the various services that each can provide to the grid and provides the cost assessment for each enabling technology. In addition to a report, this research includes a Demand Response Advanced Controls Database and User Manual. They are intended to provide users with the data that underlies this research and instructions for how to use that database more effectively and efficiently.

High Efficiency, Low Cost Scintillators for PET

International Nuclear Information System (INIS)

Kanai Shah

2007-01-01

Inorganic scintillation detectors coupled to PMTs are an important element of medical imaging applications such as positron emission tomography (PET). Performance as well as cost of these systems is limited by the properties of the scintillation detectors available at present. The Phase I project was aimed at demonstrating the feasibility of producing high performance scintillators using a low cost fabrication approach. Samples of these scintillators were produced and their performance was evaluated. Overall, the Phase I effort was very successful. The Phase II project will be aimed at advancing the new scintillation technology for PET. Large samples of the new scintillators will be produced and their performance will be evaluated. PET modules based on the new scintillators will also be built and characterized

Innovative technology summary report: High-speed clamshell pipe cutter

International Nuclear Information System (INIS)

1998-09-01

The Hanford Site C Reactor Technology Demonstration Group demonstrated the High-Speed Clamshell Pipe Cutter technology, developed and marketed by Tri Tool Inc. (Rancho Cordova, California). The models demonstrated are portable, split-frame pipe lathes that require minimal radial and axial clearances for severing and/or beveling in-line pipe with ranges of 25 cm to 41 cm and 46 cm to 61 cm nominal diameter. The radial clearance requirement from the walls, floors, or adjacent pipes is 18 cm. The lathes were supplied with carbide insert conversion kits for the cutting bits for the high-speed technique that was demonstrated. Given site-specific factors, this demonstration showed the cost of the improved technology to be approximately 30% higher than the traditional (baseline) technology (oxyacetylene torch) cost of $14,400 for 10 cuts of contaminated 41-cm and 61-cm-diameter pipe at C Reactor. Actual cutting times were faster than the baseline technology; however, moving/staging the equipment took longer. Unlike the baseline torch, clamshell lathes do not involve applied heat, flames, or smoke and can be operated remotely, thereby helping personal exposures to be as low as reasonably achievable. The baseline technology was demonstrated at the C Reactor north and south water pipe tunnels August 19--22, 1997. The improved technology was demonstrated in the gas pipe tunnel December 15--19

High Performance, Low Cost Hydrogen Generation from Renewable Energy

Energy Technology Data Exchange (ETDEWEB)

Ayers, Katherine [Proton OnSite; Dalton, Luke [Proton OnSite; Roemer, Andy [Proton OnSite; Carter, Blake [Proton OnSite; Niedzwiecki, Mike [Proton OnSite; Manco, Judith [Proton OnSite; Anderson, Everett [Proton OnSite; Capuano, Chris [Proton OnSite; Wang, Chao-Yang [Penn State University; Zhao, Wei [Penn State University

2014-02-05

Renewable hydrogen from proton exchange membrane (PEM) electrolysis is gaining strong interest in Europe, especially in Germany where wind penetration is already at critical levels for grid stability. For this application as well as biogas conversion and vehicle fueling, megawatt (MW) scale electrolysis is required. Proton has established a technology roadmap to achieve the necessary cost reductions and manufacturing scale up to maintain U.S. competitiveness in these markets. This project represents a highly successful example of the potential for cost reduction in PEM electrolysis, and provides the initial stack design and manufacturing development for Proton’s MW scale product launch. The majority of the program focused on the bipolar assembly, from electrochemical modeling to subscale stack development through prototyping and manufacturing qualification for a large active area cell platform. Feasibility for an advanced membrane electrode assembly (MEA) with 50% reduction in catalyst loading was also demonstrated. Based on the progress in this program and other parallel efforts, H2A analysis shows the status of PEM electrolysis technology dropping below $3.50/kg production costs, exceeding the 2015 target.

Leveraging Technology to Reduce Patient Transaction Costs.

Science.gov (United States)

Edlow, Richard C

2015-01-01

Medical practices are under significant pressure to provide superior customer service in an environment of declining or flat reimbursement. The solution for many practices involves the integration of a variety of third-party technologies that conveniently interface with one's electronic practice management and medical records systems. Typically, the applications allow the practice to reduce the cost of each patient interaction. Drilling down to quantify the cost of each individual patient interaction helps to determine the practicality of implementation.

Analysis of the cost impact of the new technologies in e-tail

OpenAIRE

Cristina DRUMEA

2015-01-01

The impact of new technologies on retail is studied in terms of costs. Starting from the idea that reducing costs should have a significant effect of the new technologies in retail, it is investigated the possibility that it actually constitutes the basis of a new facette of the cost leadership generic strategy. Exploratory research tracks some automation effects on transaction costs and labour costs in retail. General business models in the field are analysed, with a focus on some concrete w...

Integrated assessment of energy efficiency technologies and CO_2 abatement cost curves in China’s road passenger car sector

International Nuclear Information System (INIS)

Peng, Bin-Bin; Fan, Ying; Xu, Jin-Hua

2016-01-01

Highlights: • Energy efficiency technologies in Chinese passenger cars are classified in detail. • CO_2-reduction potential and abatement cost are analyzed for technology bundles. • Marginal abatement cost curve is established from both micro and macro perspectives. • Spark ignition, diesel and hybrid electric vehicle paths should be firstly promoted. • Technology promotion should start from the area of taxies and high-performance cars. - Abstract: Road transport is one of the main sources of energy consumption and CO_2 emissions. It is essential to conserve energy and reduce emissions by promoting energy efficiency technologies (EETs) in this sector. This study first identifies EETs for the passenger cars and then classifies them into various technology bundles. It then analyzes the CO_2-reduction potentials and emissions abatement costs of 55 type-path, 246 type-path-technology, and 465 type-path-subtechnology bundles from micro-vehicular and macro-industrial perspectives during 2010–2030, based on which marginal abatement cost (MAC) curve for China’s road passenger car sector is established. Results show that the cumulative CO_2-reduction potential of EETs on passenger cars in China during 2010–2030 is about 2698.8 Mt, but only 4% is cost-effective. The EETs with low emissions abatement costs are mainly available in the spark ignition (SI), diesel, and hybrid electric vehicle (HEV) paths on the taxis and high-performance cars, and also in the transmission, vehicle body and SI technologies on the private cars, which could be promoted at present. The technologies with large emissions reduction potential are mainly available in the plug-in hybrid electric vehicle (PHEV) and electric vehicle (EV) paths, which would be the main channels for reducing carbon emissions in the long run.

High and rising health care costs.

Science.gov (United States)

Ginsburg, Paul B

2008-10-01

The U.S. is spending a growing share of the GDP on health care, outpacing other industrialized countries. This synthesis examines why costs are higher in the U.S. and what is driving their growth. Key findings include: health care inefficiency, medical technology and health status (particularly obesity) are the primary drivers of rising U.S. health care costs. Health payer systems that reward inefficiencies and preempt competition have impeded productivity gains in the health care sector. The best evidence indicates medical technology accounts for one-half to two-thirds of spending growth. While medical malpractice insurance and defensive medicine contribute to health costs, they are not large enough factors to significantly contribute to a rise in spending. Research is consistent that demographics will not be a significant factor in driving spending despite the aging baby boomers.

The cost of radiotherapy in a decade of technology evolution

International Nuclear Information System (INIS)

Van de Werf, Evelyn; Verstraete, Jan; Lievens, Yolande

2012-01-01

Purpose: To quantify changes in radiotherapy costs occurring in a decade of medical–technological evolution. Materials and methods: The activity-based costing (ABC) model of University Hospitals Leuven (UHL) radiotherapy (RT) department was adapted to current RT standards. It allocated actual resource costs to the treatments based on the departmental work-flow and patient mix in 2009. A benchmark with the former model analyzed the cost increases related to changes in RT infrastructure and practice over 10 years. Results: A considerable increase in total RT costs was observed, resulting from higher capital investments (96%) and personnel cost (103%), the latter dominating the total picture. Treatment delivery remains the most costly activity, boosted by the cost of improved quality assurance (QA), 23% of total product costs, coming along with more advanced RT techniques. Hence, cost increases at the product level are most obvious for complex treatments, such as intensity-modulated radiotherapy (IMRT), representing cost increases ranging between 38% and 88% compared to conformal approaches. Conclusions: The ABC model provides insight into the financial consequences of evolving technology and practice. Such data are a mandatory first step in our strive to prove RT cost-effectiveness and thus support optimal reimbursement and provision of radiotherapy departments.

Very Low-Cost, Rugged, High-Vacuum System for Mass Spectrometers, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — NASA, the DoD, DHS, and commercial industry have a pressing need for miniaturized, rugged, low-cost, high vacuum systems. Recent advances in sensor technology at...

RE-COST: Cost and Business Comparisons of Renewable vs. Non-renewable Technologies

Energy Technology Data Exchange (ETDEWEB)

Mostajo Veiga, Mercedes; Farina Alvarez, Pablo; Fernandez-Montes Moraleda, Manuel; Kleinsorge, Anne

2012-07-15

Based on real plant data, the RE-COST project concludes that in many OECD energy markets, new renewable energy technologies (RET) are close to be competitive with non-RET electricity plants. RET costs are decreasing rapidly, while conventional power plants are affected by lower utilisation rates, volatile coal and gas prices, CO2 pricing, and lower electricity demand than expected. If energy prices would account for air pollution and climate change, renewables would already be the most beneficial for society and business.

Techno-Economic Feasibility of Highly Efficient Cost-Effective Thermoelectric-SOFC Hybrid Power Generation Systems

Energy Technology Data Exchange (ETDEWEB)

Jifeng Zhang; Jean Yamanis

2007-09-30

Solid oxide fuel cell (SOFC) systems have the potential to generate exhaust gas streams of high temperature, ranging from 400 to 800 C. These high temperature gas streams can be used for additional power generation with bottoming cycle technologies to achieve higher system power efficiency. One of the potential candidate bottoming cycles is power generation by means of thermoelectric (TE) devices, which have the inherent advantages of low noise, low maintenance and long life. This study was to analyze the feasibility of combining coal gas based SOFC and TE through system performance and cost techno-economic modeling in the context of multi-MW power plants, with 200 kW SOFC-TE module as building blocks. System and component concepts were generated for combining SOFC and TE covering electro-thermo-chemical system integration, power conditioning system (PCS) and component designs. SOFC cost and performance models previously developed at United Technologies Research Center were modified and used in overall system analysis. The TE model was validated and provided by BSST. The optimum system in terms of energy conversion efficiency was found to be a pressurized SOFC-TE, with system efficiency of 65.3% and cost of $390/kW of manufacturing cost. The pressurization ratio was approximately 4 and the assumed ZT of the TE was 2.5. System and component specifications were generated based on the modeling study. The major technology and cost barriers for maturing the system include pressurized SOFC stack using coal gas, the high temperature recycle blowers, and system control design. Finally, a 4-step development roadmap is proposed for future technology development, the first step being a 1 kW proof-of-concept demonstration unit.

Estimating costs in the economic evaluation of medical technologies.

Science.gov (United States)

Luce, B R; Elixhauser, A

1990-01-01

The complexities and nuances of evaluating the costs associated with providing medical technologies are often underestimated by analysts engaged in economic evaluations. This article describes the theoretical underpinnings of cost estimation, emphasizing the importance of accounting for opportunity costs and marginal costs. The various types of costs that should be considered in an analysis are described; a listing of specific cost elements may provide a helpful guide to analysis. The process of identifying and estimating costs is detailed, and practical recommendations for handling the challenges of cost estimation are provided. The roles of sensitivity analysis and discounting are characterized, as are determinants of the types of costs to include in an analysis. Finally, common problems facing the analyst are enumerated with suggestions for managing these problems.

Future directions of defense programs high-level waste technology programs

International Nuclear Information System (INIS)

Chee, T.C.; Shupe, M.W.; Turner, D.A.; Campbell, M.H.

1987-01-01

The Department of Energy has been managing high-level waste from the production of nuclear materials for defense activities over the last forty years. An objective for the Defense Waste and Transportation Management program is to develop technology which ensures the safe, permanent disposal of all defense radioactive wastes. Technology programs are underway to address the long-term strategy for permanent disposal of high-level waste generated at each Department of Energy site. Technology is being developed for assessing the hazards, environmental impacts, and costs of each long-term disposal alternative for selection and implementation. This paper addresses key technology development areas, and consideration of recent regulatory requirements associated with the long-term management of defense radioactive high-level waste

The Design and Implementation of a Low Cost and High Security Smart Home System Based on Wi-Fi and SSL Technologies

Science.gov (United States)

Xu, Chong-Yao; Zheng, Xin; Xiong, Xiao-Ming

2017-02-01

With the development of Internet of Things (IoT) and the popularity of intelligent mobile terminals, smart home system has come into people’s vision. However, due to the high cost, complex installation and inconvenience, as well as network security issues, smart home system has not been popularized. In this paper, combined with Wi-Fi technology, Android system, cloud server and SSL security protocol, a new set of smart home system is designed, with low cost, easy operation, high security and stability. The system consists of Wi-Fi smart node (WSN), Android client and cloud server. In order to reduce system cost and complexity of the installation, each Wi-Fi transceiver, appliance control logic and data conversion in the WSN is setup by a single chip. In addition, all the data of the WSN can be uploaded to the server through the home router, without having to transit through the gateway. All the appliance status information and environmental information are preserved in the cloud server. Furthermore, to ensure the security of information, the Secure Sockets Layer (SSL) protocol is used in the WSN communication with the server. What’s more, to improve the comfort and simplify the operation, Android client is designed with room pattern to control home appliances more realistic, and more convenient.

Market diffusion, technological learning, and cost-benefit dynamics of condensing gas boilers in the Netherlands

International Nuclear Information System (INIS)

Weiss, Martin; Dittmar, Lars; Junginger, Martin; Patel, Martin K.; Blok, Kornelis

2009-01-01

High costs often prevent the market diffusion of novel and efficient energy technologies. Monitoring cost and price decline for these technologies is thus important in order to establish effective energy policy. Here, we present experience curves and cost-benefit analyses for condensing gas boilers produced and sold in the Netherlands between 1981 and 2006. For the most dominant boiler type on the Dutch market, i.e., condensing gas combi boilers, we identify learning rates of 14±1% for the average price and 16±8% for the additional price relative to non-condensing devices. Economies of scale, competitive sourcing of boiler components, and improvements in boiler assembly are among the main drivers behind the observed price decline. The net present value of condensing gas combi boilers shows an overall increasing trend. Purchasing in 2006 a gas boiler of this type instead of a non-condensing device generates a net present value of 970 EUR (Euro) and realizes CO 2 (carbon dioxide) emission savings at negative costs of -120 EUR per tonne CO 2 . We attribute two-thirds of the improvements in the cost-benefit performance of condensing gas combi boilers to technological learning and one-third to a combination of external effects and governmental policies.

Cost-Effective ISS Space-Environment Technology Validation of Advanced Roll-Out Solar Array (ROSA), Phase II

Data.gov (United States)

National Aeronautics and Space Administration — DSS proposes to systematically mature, mitigate risk for; and perform hardware-based ground validations / demonstrations of a low-cost, high technology payoff,...

Solar thermal technology development: Estimated market size and energy cost savings. Volume 1: Executive summary

Science.gov (United States)

Gates, W. R.

1983-02-01

Estimated future energy cost savings associated with the development of cost-competitive solar thermal technologies (STT) are discussed. Analysis is restricted to STT in electric applications for 16 high-insolation/high-energy-price states. The fuel price scenarios and three 1990 STT system costs are considered, reflecting uncertainty over future fuel prices and STT cost projections. STT R&D is found to be unacceptably risky for private industry in the absence of federal support. Energy cost savings were projected to range from $0 to $10 billion (1990 values in 1981 dollars), dependng on the system cost and fuel price scenario. Normal R&D investment risks are accentuated because the Organization of Petroleum Exporting Countries (OPEC) cartel can artificially manipulate oil prices and undercut growth of alternative energy sources. Federal participation in STT R&D to help capture the potential benefits of developing cost-competitive STT was found to be in the national interest.

Solar thermal technology development: Estimated market size and energy cost savings. Volume 1: Executive summary

Science.gov (United States)

Gates, W. R.

1983-01-01

Estimated future energy cost savings associated with the development of cost-competitive solar thermal technologies (STT) are discussed. Analysis is restricted to STT in electric applications for 16 high-insolation/high-energy-price states. The fuel price scenarios and three 1990 STT system costs are considered, reflecting uncertainty over future fuel prices and STT cost projections. STT R&D is found to be unacceptably risky for private industry in the absence of federal support. Energy cost savings were projected to range from $0 to $10 billion (1990 values in 1981 dollars), dependng on the system cost and fuel price scenario. Normal R&D investment risks are accentuated because the Organization of Petroleum Exporting Countries (OPEC) cartel can artificially manipulate oil prices and undercut growth of alternative energy sources. Federal participation in STT R&D to help capture the potential benefits of developing cost-competitive STT was found to be in the national interest.

Towards a questionnaire for measuring affective benefits and costs of communication technologies

NARCIS (Netherlands)

Markopoulos, P.; Yarosh, S.; Abowd, G.

2014-01-01

As CSCW creates and investigates technologies for social communication, it is important to understand the emotional benefits and costs of these systems. We propose the Affec-tive Benefits and Costs of Communication Technologies (ABCCT) questionnaire to supplement traditional qualita-tive methods of

Analysis of the cost impact of the new technologies in e-tail

Directory of Open Access Journals (Sweden)

Cristina DRUMEA

2015-06-01

Full Text Available The impact of new technologies on retail is studied in terms of costs. Starting from the idea that reducing costs should have a significant effect of the new technologies in retail, it is investigated the possibility that it actually constitutes the basis of a new facette of the cost leadership generic strategy. Exploratory research tracks some automation effects on transaction costs and labour costs in retail. General business models in the field are analysed, with a focus on some concrete ways of implementation in retail, particularly as e-tail. In the background we grasp and discuss the aspects of the financial flows related to trade. Even when those issues may prevail, one cannot elude discussing the cultural and ethical standards associated to the trade new features induced by e-tail and the new technologies.

The impact of new technology on compact disposal costs

International Nuclear Information System (INIS)

Arrowsmith, H.W.; Zidow, T.M.

1989-01-01

The cost of disposal of low-level waste (LLW) has increased dramatically since the 1960s. In the '60s waste was put into the ground for a fee of less than $1/ft 3 in truck-size quantities. Fees for the same burial services today begin in the $30/ft 3 range and increase rapidly from that level. Although the user fees associated with compacts will clearly exceed $100/ft 3 , improved operating techniques by the generators will reduce the amount of waste produced. Current estimates suggest this reduction will drive the per-cubic-foot cost of disposal over the $200 mark. Technology is the only solution to this predicament. While costs already incurred will contribute to the fixed portion of the base user fees, the means to minimize the variable portion of the fees in now at hand. This variable portion results from on-site processing costs, waste form stability enhancements, and ongoing disposal unit construction. Technology exists to minimize volume through ultra compaction and selective incineration, greatly reducing the ongoing disposal unit construction requirements. Vitrification of incinerator residue provides waste form stability far in excess of that provided by concrete overpacks. As overpacks represent the second largest material cost at an engineered barrier facility, the potential for cost savings is substantial

Dramatically improve the Safety Performance of Li ion Battery Separators and Reduce the Manufacturing Cost Using Ultraviolet Curing and High Precision Coating Technologies

Energy Technology Data Exchange (ETDEWEB)

Voelker, Gary [Miltec UV International, LLC, Stevensville, MD (United States); Arnold, John [Miltec UV International, LLC, Stevensville, MD (United States)

2017-06-30

The objective of this project was to improve the safety of operation of Lithium ion batteries (LIB)and at the same time significantly reduce the manufacturing cost of LIB separators. The project was very successful in demonstrating the improved performance and reduced cost attributed to using UV curable binder and high speed printing technology to place a very thin and precisely controlled ceramic layer on the surface of base separators made of polyolefins such as Polyethylene, Polypropylene and combinations of the two as well as cellulosic base separators. The underlying need for this new technology is the recently identified potential of fire in large format Lithium ion batteries used in hybrid, plug-in hybrid and electric vehicles. The primary potential cause of battery fire is thermal runaway caused by several different electrical or mechanical mechanisms; such as, overcharge, puncture, overheating, compaction, and internal short circuit. During thermal runaway, the ideal separator prevents ion flow and continues to physically separate the anode from the cathode. If the temperature of the battery gets higher, the separator may melt and partially clog the pores and help prevent ion flows but it also can shrink which can result in physical contact of the electrodes and accelerate thermal run-away even further. Ceramic coated separators eliminate many of the problems related to the usage of traditional separators. The ceramic coating provides an electrically insulating layer that retains its physical integrity at high temperature, allows for more efficient thermal heat transfer, helps reduce thermal shrinkage, and inhibits dendrite growth that could create a potential short circuit. The use of Ultraviolet (UV) chemistry to bind fine ceramic particles on separators is a unique and innovative approach primarily because of the instant curing of the UV curable binder upon exposure to UV light. This significant reduction in drying/curing time significantly reduces the

Alternative ceramic circuit constructions for low cost, high reliability applications

International Nuclear Information System (INIS)

Modes, Ch.; O'Neil, M.

1997-01-01

The growth in the use of hybrid circuit technology has recently been challenged by recent advances in low cost laminate technology, as well as the continued integration of functions into IC's. Size reduction of hybrid 'packages' has turned out to be a means to extend the useful life of this technology. The suppliers of thick film materials technology have responded to this challenge by developing a number of technology options to reduce circuit size, increase density, and reduce overall cost, while maintaining or increasing reliability. This paper provides an overview of the processes that have been developed, and, in many cases are used widely to produce low cost, reliable microcircuits. Comparisons of each of these circuit fabrication processes are made with a discussion of advantages and disadvantages of each technology. (author)

Cost of organic waste technologies: A case study for New Jersey

Directory of Open Access Journals (Sweden)

Gal Hochman

2015-09-01

Full Text Available This paper evaluates the benefits of converting food waste and manure to biogas and/or fertilizer, while focusing on four available waste treatment technologies: direct combustion, landfilling, composting, and anaerobic digestion. These four alternative technologies were simulated using municipal-level data on food waste and manure in New Jersey. The criteria used to assess the four technologies include technological productivity, economic benefits, and impact on land scarcity. Anaerobic digestion with gas collection has the highest technological productivity; using anaerobic digesters would supply electricity to nearly ten thousand families in New Jersey. In terms of economic benefits, the landfill to gas method is the least costly method of treating waste. In comparison, direct combustion is by far the most costly method of all four waste-to-energy technologies.

Cost effectiveness and efficiency in assistive technology service delivery.

Science.gov (United States)

Warren, C G

1993-01-01

In order to develop and maintain a viable service delivery program, the realities of cost effectiveness and cost efficiency in providing assistive technology must be addressed. Cost effectiveness relates to value of the outcome compared to the expenditures. Cost efficiency analyzes how a provider uses available resources to supply goods and services. This paper describes how basic business principles of benefit/cost analysis can be used to determine cost effectiveness. In addition, basic accounting principles are used to illustrate methods of evaluating a program's cost efficiency. Service providers are encouraged to measure their own program's effectiveness and efficiency (and potential viability) in light of current trends. This paper is meant to serve as a catalyst for continued dialogue on this topic.

Cost and benefit estimates of partially-automated vehicle collision avoidance technologies.

Science.gov (United States)

Harper, Corey D; Hendrickson, Chris T; Samaras, Constantine

2016-10-01

Many light-duty vehicle crashes occur due to human error and distracted driving. Partially-automated crash avoidance features offer the potential to reduce the frequency and severity of vehicle crashes that occur due to distracted driving and/or human error by assisting in maintaining control of the vehicle or issuing alerts if a potentially dangerous situation is detected. This paper evaluates the benefits and costs of fleet-wide deployment of blind spot monitoring, lane departure warning, and forward collision warning crash avoidance systems within the US light-duty vehicle fleet. The three crash avoidance technologies could collectively prevent or reduce the severity of as many as 1.3 million U.S. crashes a year including 133,000 injury crashes and 10,100 fatal crashes. For this paper we made two estimates of potential benefits in the United States: (1) the upper bound fleet-wide technology diffusion benefits by assuming all relevant crashes are avoided and (2) the lower bound fleet-wide benefits of the three technologies based on observed insurance data. The latter represents a lower bound as technology is improved over time and cost reduced with scale economies and technology improvement. All three technologies could collectively provide a lower bound annual benefit of about $18 billion if equipped on all light-duty vehicles. With 2015 pricing of safety options, the total annual costs to equip all light-duty vehicles with the three technologies would be about $13 billion, resulting in an annual net benefit of about $4 billion or a $20 per vehicle net benefit. By assuming all relevant crashes are avoided, the total upper bound annual net benefit from all three technologies combined is about $202 billion or an $861 per vehicle net benefit, at current technology costs. The technologies we are exploring in this paper represent an early form of vehicle automation and a positive net benefit suggests the fleet-wide adoption of these technologies would be beneficial

Energy technologies for distributed utility applications: Cost and performance trends, and implications for photovoltaics

International Nuclear Information System (INIS)

Eyer, J.M.

1994-01-01

Utilities are evaluating several electric generation and storage (G ampersand S) technologies for distributed utility (DU) applications. Attributes of leading DU technologies and implications for photovoltaics (PV) are described. Included is a survey of present and projected cost and performance for: (1) small, advanced combustion turbines (CTs); (2) advanced, natural gas-fired, diesel engines (diesel engines); and (3) advanced lead-acid battery systems (batteries). Technology drivers and relative qualitative benefits are described. A levelized energy cost-based cost target for PV for DU applications is provided. The analysis addresses only relative cost, for PV and for three selected alternative DU technologies. Comparable size, utility, and benefits are assumed, although relative value is application-specific and often technology- and site-specific

Aqueous nitrate waste treatment: Technology comparison, cost/benefit, and market analysis

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

The purpose of this analysis is to provide information necessary for the Department of Energy (DOE) to evaluate the practical utility of the Nitrate to Ammonia and Ceramic or Glass (NAC/NAG/NAX) process, which is under development in the Oak Ridge National Laboratory. The NAC/NACx/NAX process can convert aqueous radioactive nitrate-laden waste to a glass, ceramic, or grout solid waste form. The tasks include, but are not limited to, the following: Identify current commercial technologies to meet hazardous and radiological waste disposal requirements. The technologies may be thermal or non-thermal but must be all inclusive (i.e., must convert a radionuclide-containing nitrate waste with a pH around 12 to a stable form that can be disposed at permitted facilities); evaluate and compare DOE-sponsored vitrification, grouting, and minimum additive waste stabilization projects for life-cycle costs; compare the technologies above with respect to material costs, capital equipment costs, operating costs, and operating efficiencies. For the NAC/NAG/NAX process, assume aluminum reactant is government furnished and ammonia gas may be marketed; compare the identified technologies with respect to frequency of use within DOE for environmental management applications with appropriate rationale for use; Assess the potential size of the DOE market for the NAC/NAG/NAX process; assess and off-gas issues; and compare with international technologies, including life-cycle estimates.

Aqueous nitrate waste treatment: Technology comparison, cost/benefit, and market analysis

International Nuclear Information System (INIS)

1994-01-01

The purpose of this analysis is to provide information necessary for the Department of Energy (DOE) to evaluate the practical utility of the Nitrate to Ammonia and Ceramic or Glass (NAC/NAG/NAX) process, which is under development in the Oak Ridge National Laboratory. The NAC/NACx/NAX process can convert aqueous radioactive nitrate-laden waste to a glass, ceramic, or grout solid waste form. The tasks include, but are not limited to, the following: Identify current commercial technologies to meet hazardous and radiological waste disposal requirements. The technologies may be thermal or non-thermal but must be all inclusive (i.e., must convert a radionuclide-containing nitrate waste with a pH around 12 to a stable form that can be disposed at permitted facilities); evaluate and compare DOE-sponsored vitrification, grouting, and minimum additive waste stabilization projects for life-cycle costs; compare the technologies above with respect to material costs, capital equipment costs, operating costs, and operating efficiencies. For the NAC/NAG/NAX process, assume aluminum reactant is government furnished and ammonia gas may be marketed; compare the identified technologies with respect to frequency of use within DOE for environmental management applications with appropriate rationale for use; Assess the potential size of the DOE market for the NAC/NAG/NAX process; assess and off-gas issues; and compare with international technologies, including life-cycle estimates

Low cost options for tissue culture technology in developing countries. Proceedings of a technical meeting

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-02-01

Tissue culture technology is used for the production of doubled haploids, cryopreservation, propagating new plant varieties, conserving rare and endangered plants, difficult-to-propagate plants, and to produce secondary metabolites and transgenic plants. The production of high quality planting material of crop plants and fruit trees, propagated from vegetative parts, has created new opportunities in global trading, benefited growers, farmers, and nursery owners, and improved rural employment. However, there are still major opportunities to produce and distribute high quality planting material, e.g. crops like banana, date palm, cassava, pineapple, plantain, potato, sugarcane, sweet potato, yams, ornamentals, fruit and forest trees. The main advantage of tissue culture technology lies in the production of high quality and uniform planting material that can be multiplied on a year-round basis under disease-free conditions anywhere irrespective of the season and weather. However, the technology is capital, labor and energy intensive. Although, labor is cheap in many developing countries, the resources of trained personnel and equipment are often not readily available. In addition, energy, particularly electricity, and clean water are costly. The energy requirements for tissue culture technology depend on day temperature, day-length and relative humidity, and they have to be controlled during the process of propagation. Individual plant species also differ in their growth requirements. Hence, it is necessary to have low cost options for weaning, hardening of micropropagated plants and finally growing them in the field. This publication describes options for reducing costs to establish and operate tissue culture facilities and primarily focus on plant micropropagation. It includes papers on the basics of tissue culture technology, low cost options for the design of laboratories, use of culture media and containers, energy and labor saving, integration and adoption of

Low cost options for tissue culture technology in developing countries. Proceedings of a technical meeting

International Nuclear Information System (INIS)

2004-02-01

Tissue culture technology is used for the production of doubled haploids, cryopreservation, propagating new plant varieties, conserving rare and endangered plants, difficult-to-propagate plants, and to produce secondary metabolites and transgenic plants. The production of high quality planting material of crop plants and fruit trees, propagated from vegetative parts, has created new opportunities in global trading, benefited growers, farmers, and nursery owners, and improved rural employment. However, there are still major opportunities to produce and distribute high quality planting material, e.g. crops like banana, date palm, cassava, pineapple, plantain, potato, sugarcane, sweet potato, yams, ornamentals, fruit and forest trees. The main advantage of tissue culture technology lies in the production of high quality and uniform planting material that can be multiplied on a year-round basis under disease-free conditions anywhere irrespective of the season and weather. However, the technology is capital, labor and energy intensive. Although, labor is cheap in many developing countries, the resources of trained personnel and equipment are often not readily available. In addition, energy, particularly electricity, and clean water are costly. The energy requirements for tissue culture technology depend on day temperature, day-length and relative humidity, and they have to be controlled during the process of propagation. Individual plant species also differ in their growth requirements. Hence, it is necessary to have low cost options for weaning, hardening of micropropagated plants and finally growing them in the field. This publication describes options for reducing costs to establish and operate tissue culture facilities and primarily focus on plant micropropagation. It includes papers on the basics of tissue culture technology, low cost options for the design of laboratories, use of culture media and containers, energy and labor saving, integration and adoption of

Novel Low Cost, High Reliability Wind Turbine Drivetrain

Energy Technology Data Exchange (ETDEWEB)

Chobot, Anthony; Das, Debarshi; Mayer, Tyler; Markey, Zach; Martinson, Tim; Reeve, Hayden; Attridge, Paul; El-Wardany, Tahany

2012-09-13

Clipper Windpower, in collaboration with United Technologies Research Center, the National Renewable Energy Laboratory, and Hamilton Sundstrand Corporation, developed a low-cost, deflection-compliant, reliable, and serviceable chain drive speed increaser. This chain and sprocket drivetrain design offers significant breakthroughs in the areas of cost and serviceability and addresses the key challenges of current geared and direct-drive systems. The use of gearboxes has proven to be challenging; the large torques and bending loads associated with use in large multi-MW wind applications have generally limited demonstrated lifetime to 8-10 years [1]. The large cost of gearbox replacement and the required use of large, expensive cranes can result in gearbox replacement costs on the order of $1M, representing a significant impact to overall cost of energy (COE). Direct-drive machines eliminate the gearbox, thereby targeting increased reliability and reduced life-cycle cost. However, the slow rotational speeds require very large and costly generators, which also typically have an undesirable dependence on expensive rare-earth magnet materials and large structural penalties for precise air gap control. The cost of rare-earth materials has increased 20X in the last 8 years representing a key risk to ever realizing the promised cost of energy reductions from direct-drive generators. A common challenge to both geared and direct drive architectures is a limited ability to manage input shaft deflections. The proposed Clipper drivetrain is deflection-compliant, insulating later drivetrain stages and generators from off-axis loads. The system is modular, allowing for all key parts to be removed and replaced without the use of a high capacity crane. Finally, the technology modularity allows for scalability and many possible drivetrain topologies. These benefits enable reductions in drivetrain capital cost by 10.0%, levelized replacement and O&M costs by 26.7%, and overall cost of

Staged, High-Pressure Oxy-Combustion Technology: Development and Scale-Up

Energy Technology Data Exchange (ETDEWEB)

Axelbaum, Richard [Washington Univ., St. Louis, MO (United States); Kumfer, Benjamin [Washington Univ., St. Louis, MO (United States); Gopan, Akshay [Washington Univ., St. Louis, MO (United States); Yang, Zhiwei [Washington Univ., St. Louis, MO (United States); Phillips, Jeff [Electric Power Research Inst. (EPRI), Palo Alto, CA (United States); Pint, Bruce [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-12-29

The immediate need for a high efficiency, low cost carbon capture process has prompted the recent development of pressurized oxy-combustion. With a greater combustion pressure the dew point of the flue gas is increased, allowing for effective integration of the latent heat of flue gas moisture into the Rankine cycle. This increases the net plant efficiency and reduces costs. A novel, transformational process, named Staged, Pressurized Oxy-Combustion (SPOC), achieves additional step changes in efficiency and cost reduction by significantly reducing the recycle of flue gas. The research and development activities conducted under Phases I and II of this project (FE0009702) include: SPOC power plant cost and performance modeling, CFD-assisted design of pressurized SPOC boilers, theoretical analysis of radiant heat transfer and ash deposition, boiler materials corrosion testing, construction of a 100 kWth POC test facility, and experimental testing. The results of this project have advanced the technology readiness level (TRL) of the SPOC technology from 1 to 5.

Electrification Futures Study: End-Use Electric Technology Cost and Performance Projections through 2050

Energy Technology Data Exchange (ETDEWEB)

Vimmerstedt, Laura J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Jadun, Paige [National Renewable Energy Lab. (NREL), Golden, CO (United States); McMillan, Colin A. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Steinberg, Daniel C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Muratori, Matteo [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mai, Trieu T. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2018-01-02

This report provides projected cost and performance assumptions for electric technologies considered in the Electrification Futures Study, a detailed and comprehensive analysis of the effects of widespread electrification of end-use service demands in all major economic sectors - transportation, residential and commercial buildings, and industry - for the contiguous United States through 2050. Using extensive literature searches and expert assessment, the authors identify slow, moderate, and rapid technology advancement sensitivities on technology cost and performance, and they offer a comparative analysis of levelized cost metrics as a reference indicator of total costs. The identification and characterization of these end-use service demand technologies is fundamental to the Electrification Futures Study. This report, the larger Electrification Futures Study, and the associated data and methodologies may be useful to planners and analysts in evaluating the potential role of electrification in an uncertain future. The report could be broadly applicable for other analysts and researchers who wish to assess electrification and electric technologies.

Cost Estimation and Comparison of Carbon Capture and Storage Technology with Wind Energy

Directory of Open Access Journals (Sweden)

ABDULLAH MENGAL

2017-04-01

Full Text Available The CCS (Carbon Capture and Storage is one of the significant solutions to reduce CO2 emissions from fossil fuelled electricity generation plants and minimize the effect of global warming. Economic analysis of CCS technology is, therefore, essential for the feasibility appraisal towards CO2 reduction. In this paper LCOE (Levelized Cost of Electricity Generation has been estimated with and without CCS technology for fossil fuel based power plants of Pakistan and also further compared with computed LCOE of WE (Wind Energy based power plants of the Pakistan. The results of this study suggest that the electricity generation costs of the fossil fuel power plants increase more than 44% with CCS technology as compared to without CCS technology. The generation costs are also found to be 10% further on higher side when considering efficiency penalty owing to installation of CCS technology. In addition, the CO2 avoided costs from natural gas plant are found to be 40 and 10% higher than the local coal and imported coal plants respectively. As such, the electricity generation cost of 5.09 Rs/kWh from WE plants is found to be competitive even when fossil fuel based plants are without CCS technology, with lowest cost of 5.9 Rs./kWh of CCNG (Combined Cycle Natural Gas plant. Based on analysis of results of this study and anticipated future development of efficient and cheap WE technologies, it is concluded that WE based electricity generation would be most appropriate option for CO2 reduction for Pakistan.

Thin Mirror Shaping Technology for High-Throughput X-ray Telescopes

Science.gov (United States)

Schattenburg, Mark

This proposal is submitted to the NASA Research Opportunities in Space and Earth Sciences program (ROSES-2012) in response to NASA Research Announcement NNH12ZDA001N- APRA. It is targeted to the Astronomy and Astrophysics Research and Analysis (APRA) program element under the Supporting Technology category. Powerful x-ray telescope mirrors are critical components of a raft of small-to-large mission concepts under consideration by NASA. The science questions addressed by these missions have certainly never been more compelling and the need to fulfill NASA s core missions of exploring the universe and strengthening our nation s technology base has never been greater. Unfortunately, budgetary constraints are driving NASA to consider the cost/benefit and risk factors of new missions more carefully than ever. New technology for producing x-ray telescopes with increased resolution and collecting area, while holding down cost, are key to meeting these goals and sustaining a thriving high-energy astrophysics enterprise in the US. We propose to develop advanced technology which will lead to thin-shell x-ray telescope mirrors rivaling the Chandra x-ray telescope in spatial resolution but with 10-100X larger area all at significantly reduced weight, risk and cost. The proposed effort builds on previous research at MIT and complements NASA-supported research at other institutions. We are currently pursuing two thin-mirror technology development tracks which we propose to extend and accelerate with NASA support. The first research track utilizes rapidly-maturing thermal glass slumping technology which uses porous ceramic air-bearing mandrels to shape glass mirrors without touching, thus avoiding surface-induced mid-range spatial frequency ripples. A second research track seeks to remove any remaining mid- to long-range errors in mirrors by using scanning ion-beam implant to impart small, highly deterministic and very stable amounts of stress into thin glass, utilizing local

Using Top-down and Bottom-up Costing Approaches in LMICs: The Case for Using Both to Assess the Incremental Costs of New Technologies at Scale.

Science.gov (United States)

Cunnama, Lucy; Sinanovic, Edina; Ramma, Lebogang; Foster, Nicola; Berrie, Leigh; Stevens, Wendy; Molapo, Sebaka; Marokane, Puleng; McCarthy, Kerrigan; Churchyard, Gavin; Vassall, Anna

2016-02-01

Estimating the incremental costs of scaling-up novel technologies in low-income and middle-income countries is a methodologically challenging and substantial empirical undertaking, in the absence of routine cost data collection. We demonstrate a best practice pragmatic approach to estimate the incremental costs of new technologies in low-income and middle-income countries, using the example of costing the scale-up of Xpert Mycobacterium tuberculosis (MTB)/resistance to riframpicin (RIF) in South Africa. We estimate costs, by applying two distinct approaches of bottom-up and top-down costing, together with an assessment of processes and capacity. The unit costs measured using the different methods of bottom-up and top-down costing, respectively, are $US16.9 and $US33.5 for Xpert MTB/RIF, and $US6.3 and $US8.5 for microscopy. The incremental cost of Xpert MTB/RIF is estimated to be between $US14.7 and $US17.7. While the average cost of Xpert MTB/RIF was higher than previous studies using standard methods, the incremental cost of Xpert MTB/RIF was found to be lower. Costs estimates are highly dependent on the method used, so an approach, which clearly identifies resource-use data collected from a bottom-up or top-down perspective, together with capacity measurement, is recommended as a pragmatic approach to capture true incremental cost where routine cost data are scarce. © 2016 The Authors. Health Economics published by John Wiley & Sons Ltd.

Sensor Technology Integration for Efficient and Cost-Effective D and D

International Nuclear Information System (INIS)

Varona, J. M.; Lagos, L. E.

2002-01-01

The deactivation and decommissioning of radiologically contaminated facilities require the use of a multitude of technologies to perform characterization, decontamination, dismantlement, and waste management. Current baseline technologies do not provide adequate tools to perform this work in an efficient and cost-effective manner. Examples of such tasks that can be modified to enhance the D and D work include: floor and wall decontamination, pipe decontamination, and surveillance and monitoring. FIU-HCET's Technology Development, Integration and Deployment (TDID) group aims to enhance the D and D process by integrating sensor technology to existing decontamination and remote surveillance tools. These integrated systems have been demonstrated throughout the DOE Complex and commercial nuclear facilities undergoing decommissioning. Finding new ways of integrating technologies utilized in the decommissioning and surveillance and monitoring process has been a goal of this group during the past several years. Current and previous integration projects include: Mobile Integrated Piping Decontamination and Characterization System, On-Line Decontamination and Characterization System, In-Situ Pipe Decontamination and Unplugging System, Remote Hazardous Environment Surveyor (RHES), and the Online Handheld grit blasting decontamination system As a result of integrating sensors with D and D tools, the resulting technologies have removed the downtime currently found in baseline processes by allowing operators and project managers to have real-time contamination data during the specified D and D process. This added component allows project managers to verify that full decontamination and surveillance has been conducted. Through successful demonstration and deployments of the TDID-developed technologies, FIU-HCET has provided tools that can impact the cost, schedule and health and safety of D and D operations in a positive way, leading to shorter downtimes and significant cost

Cost-Benefit Analysis for the Advanced Near Net Shape Technology (ANNST) Method for Fabricating Stiffened Cylinders

Science.gov (United States)

Ivanco, Marie L.; Domack, Marcia S.; Stoner, Mary Cecilia; Hehir, Austin R.

2016-01-01

Low Technology Readiness Levels (TRLs) and high levels of uncertainty make it challenging to develop cost estimates of new technologies in the R&D phase. It is however essential for NASA to understand the costs and benefits associated with novel concepts, in order to prioritize research investments and evaluate the potential for technology transfer and commercialization. This paper proposes a framework to perform a cost-benefit analysis of a technology in the R&D phase. This framework was developed and used to assess the Advanced Near Net Shape Technology (ANNST) manufacturing process for fabricating integrally stiffened cylinders. The ANNST method was compared with the conventional multi-piece metallic construction and composite processes for fabricating integrally stiffened cylinders. Following the definition of a case study for a cryogenic tank cylinder of specified geometry, data was gathered through interviews with Subject Matter Experts (SMEs), with particular focus placed on production costs and process complexity. This data served as the basis to produce process flowcharts and timelines, mass estimates, and rough order-of-magnitude cost and schedule estimates. The scalability of the results was subsequently investigated to understand the variability of the results based on tank size. Lastly, once costs and benefits were identified, the Analytic Hierarchy Process (AHP) was used to assess the relative value of these achieved benefits for potential stakeholders. These preliminary, rough order-of-magnitude results predict a 46 to 58 percent reduction in production costs and a 7-percent reduction in weight over the conventional metallic manufacturing technique used in this study for comparison. Compared to the composite manufacturing technique, these results predict cost savings of 35 to 58 percent; however, the ANNST concept was heavier. In this study, the predicted return on investment of equipment required for the ANNST method was ten cryogenic tank barrels

Cost comparison of laboratory methods and four field screening technologies for uranium-contaminated soil

International Nuclear Information System (INIS)

Douthat, D.M.; Armstrong, A.Q.

1994-01-01

To address the problem of characterizing uranium-contaminated surface soil at federal facilities, the Department of Energy has the development of four uranium field screening technologies, under the direction of the Uranium-in-Soils Integrated Demonstration (USID) Program. These four technologies include: a long-range alpha detector a beta scintillation detector, an in situ gamma detector, and a mobile laser ablation-inductively coupled plasma/atomic emission spectrometry (LA-ICP/AES) laboratory. As part of the performance assessment for these field screening technologies, cost estimates for the development and operation of each technology were created. A cost study was conducted to compare three of the USID field screening technologies to the use of traditional field surveying equipment to adequately characterize surface soils of a one-acre site. The results indicate that the use of traditional equipment costs more than the in situ gamma detector, but less than the beta scintillation detector and LRAD. The use of traditional field surveying equipment results in cost savings of 4% and 34% over the use of the beta scintillation and LRAD technologies, respectively. A study of single-point surface soil sampling and laboratory analysis costs was also conducted. Operational costs of the mobile LA-ICP/AES laboratory were compared with operational costs of traditional sampling and analysis, which consists of collecting soil samples and conducting analysis in a radiochemical laboratory. The cost study indicates that the use of the mobile LA-ICP/AES laboratory results in cost savings of 23% and 40% over traditional field sampling and laboratory analysis conducted by characterization groups at two DOE facilities

Practical aspects of photovoltaic technology, applications and cost (revised)

Science.gov (United States)

Rosenblum, L.

1985-01-01

The purpose of this text is to provide the reader with the background, understanding, and computational tools needed to master the practical aspects of photovoltaic (PV) technology, application, and cost. The focus is on stand-alone, silicon solar cell, flat-plate systems in the range of 1 to 25 kWh/day output. Technology topics covered include operation and performance of each of the major system components (e.g., modules, array, battery, regulators, controls, and instrumentation), safety, installation, operation and maintenance, and electrical loads. Application experience and trends are presented. Indices of electrical service performance - reliability, availability, and voltage control - are discussed, and the known service performance of central station electric grid, diesel-generator, and PV stand-alone systems are compared. PV system sizing methods are reviewed and compared, and a procedure for rapid sizing is described and illustrated by the use of several sample cases. The rapid sizing procedure yields an array and battery size that corresponds to a minimum cost system for a given load requirement, insulation condition, and desired level of service performance. PV system capital cost and levelized energy cost are derived as functions of service performance and insulation. Estimates of future trends in PV system costs are made.

Integrative Production Technology for High-Wage Countries

CERN Document Server

2012-01-01

Industrial production in high-wage countries like Germany is still at risk. Yet, there are many counter-examples in which producing companies dominate their competitors by not only compensating for their specific disadvantages in terms of factor costs (e.g. wages, energy, duties and taxes) but rather by minimising waste using synchronising integrativity as well as by obtaining superior adaptivity on alternating conditions. In order to respond to the issue of economic sustainability of industrial production in high-wage countries, the leading production engineering and material research scientists of RWTH Aachen University together with renowned companies have established the Cluster of Excellence “Integrative Production Technology for High-Wage Countries”. This compendium comprises the cluster’s scientific results as well as a selection of business and technology cases, in which these results have been successfully implemented into industrial practice in close cooperation with more than 30 companies of ...

A methodology for financial evaluation of biogas technology in India using cost functions

International Nuclear Information System (INIS)

Rubab, S.; Kandpal, T.C.

1996-01-01

A methodology for financial evaluation of biogas technology for domestic use in India using recently developed cost functions is reported. Analytical expressions for the unit cost of biogas and cost per unit of useful energy delivered by a biogas plant in combination with other suitable technologies have been developed. Net present value and discounted pay-back period have been calculated. The sensitivity of the unit cost of biogas, the cost per unit of useful energy, and the net present value with respect to a number of variables is also reported. (author)

Algolcam: Low Cost Sky Scanning with Modern Technology

Science.gov (United States)

Connors, Martin; Bolton, Dempsey; Doktor, Ian

2016-01-01

Low cost DSLR cameras running under computer control offer good sensitivity, high resolution, small size, and the convenience of digital image handling. Recent developments in small single board computers have pushed the performance to cost and size ratio to unprecedented values, with the further advantage of very low power consumption. Yet a third technological development is motor control electronics which is easily integrated with the computer to make an automated mount, which in our case is custom built, but with similar mounts available commercially. Testing of such a system under a clear plastic dome at our auroral observatory was so successful that we have developed a weatherproof housing allowing use during the long, cold, and clear winter nights at northerly latitudes in Canada. The main advantage of this housing should be improved image quality as compared to operation through clear plastic. We have improved the driving software to include the ability to self-calibrate pointing through the web API of astrometry.net, and data can be reduced automatically through command line use of the Muniwin program. The mount offers slew in declination and RA, and tracking at sidereal or other rates in RA. Our previous tests with a Nikon D5100 with standard lenses in the focal length range 50-200 mm, operating at f/4 to f/5, allowed detection of 12th magnitude stars with 30 second exposure under very dark skies. At 85 mm focal length, a field of 15° by 10° is imaged with 4928 by 3264 color pixels, and we have adopted an 85 mm fixed focal length f/1.4 lens (as used by Project Panoptes), which we expect will give a limited magnitude approaching 15. With a large field of view, deep limiting magnitude, low cost, and ease of construction and use, we feel that the Algolcam offers great possibilities in monitoring and finding changes in the sky. We have already applied it to variable star light curves, and with a suitable pipeline for detection of moving or varying objects

Low Cost Automated Manufacture of High Efficiency THINS ZTJ PV Blanket Technology (P-NASA12-007), Phase I

Data.gov (United States)

National Aeronautics and Space Administration — NASA needs lower cost solar arrays with high performance for a variety of missions. While high efficiency, space-qualified solar cells are in themselves costly, >...

Competition between biofuels. Modeling technological learning and cost reductions over time

International Nuclear Information System (INIS)

De Wit, M.; Junginger, M.; Faaij, A.; Lensink, S.M.; Londo, H.M.

2009-10-01

A key aspect in modeling the (future) competition between biofuels is the way in which production cost developments are computed. The objective of this study was threefold: (1) to construct a (endogenous) relation between cost development and cumulative production (2) to implement technological learning based on both engineering study insights and an experience curve approach, and (3) to investigate the impact of different technological learning assumptions on the market diffusion patterns of different biofuels. The analysis was executed with the European biofuel model BioTrans, which computes the least cost biofuel route. The model meets an increasing demand, reaching a 25% share of biofuels of the overall European transport fuel demand by 2030. Results show that 1st generation biodiesel is the most cost competitive fuel, dominating the early market. With increasing demand, modestly productive oilseed crops become more expensive rapidly, providing opportunities for advanced biofuels to enter the market. While biodiesel supply typically remains steady until 2030, almost all additional yearly demands are delivered by advanced biofuels, supplying up to 60% of the market by 2030. Sensitivity analysis shows that (a) overall increasing investment costs favour biodiesel production, (b) separate gasoline and diesel subtargets may diversify feedstock production and technology implementation, thus limiting the risk of failure and preventing lock-in and (c) the moment of an advanced technology's commercial market introduction determines, to a large degree, its future chances for increasing market share.

Technology Roadmap: High-Efficiency, Low-Emissions Coal-Fired Power Generation

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

Coal is the largest source of power globally and, given its wide availability and relatively low cost, it is likely to remain so for the foreseeable future. The High-Efficiency, Low-Emissions Coal-Fired Power Generation Roadmap describes the steps necessary to adopt and further develop technologies to improve the efficiency of the global fleet of coal. To generate the same amount of electricity, a more efficient coal-fired unit will burn less fuel, emit less carbon, release less local air pollutants, consume less water and have a smaller footprint. High-efficiency, low emissions (HELE) technologies in operation already reach a thermal efficiency of 45%, and technologies in development promise even higher values. This compares with a global average efficiency for today’s fleet of coal-fired plants of 33%, where three-quarters of operating units use less efficient technologies and more than half is over 25 years old. A successful outcome to ongoing RD&D could see units with efficiencies approaching 50% or even higher demonstrated within the next decade. Generation from older, less efficient technology must gradually be phased out. Technologies exist to make coal-fired power generation much more effective and cleaner burning. Of course, while increased efficiency has a major role to play in reducing emissions, particularly over the next 10 years, carbon capture and storage (CCS) will be essential in the longer term to make the deep cuts in carbon emissions required for a low-carbon future. Combined with CCS, HELE technologies can cut CO2 emissions from coal-fired power generation plants by as much as 90%, to less than 100 grams per kilowatt-hour. HELE technologies will be an influential factor in the deployment of CCS. For the same power output, a higher efficiency coal plant will require less CO2 to be captured; this means a smaller, less costly capture plant; lower operating costs; and less CO2 to be transported and stored.

Use of cost-effective construction technologies in India to mitigate climate change

Energy Technology Data Exchange (ETDEWEB)

Sengupta, N. [Forum of Scientists, Engineers and Technologists, Kolkata (India)

2008-01-10

Concentration of greenhouse gases plays a major role in raising the earth's temperature. Carbon dioxide, produced from burning of fossil fuels, is the principle greenhouse gas and efforts are being made at international level to reduce its emission through adoption of energy-efficient technologies. The UN Conference on Environment and Development, 1992 made a significant development in this field by initiating the discussion on sustainable development under the Agenda 21. Cost-effective construction technologies can bring down the embodied energy level associated with production of building materials by lowering use of energy-consuming materials. This embodied energy is a crucial factor for sustainable construction practices and effective reduction of the same would contribute in mitigating global warming. The cost-effective construction technologies would emerge as the most acceptable case of sustainable technologies in India both in terms of cost and environment.

[Analysis of medical cost of atlantoaxial disorders in patients receiving innovated treatment technologies].

Science.gov (United States)

Wu, Yunxia; Liu, Zhongjun

2016-01-19

To explore the effects of innovated technologies and products on improving outcomes and decreasing medical costs by analyzing a total and subtotal medical costs of patients with atlantoaxial disorders. The medical costs of 1 489 patients with atlantoaxial disorders from Peking University Third Hospital from 2005 to 2014, who received innovated technologies and products treatment were retrospectively analyzed and compared.Descriptive analysis and ANOVA were used for statistical analysis, and SPSS 19.0 was used to analyze data. From 2005 to 2014, under the situation of a general increase in medical cost by 327%, the total medical costs were stable for patients who used innovated technologies and products for treatment, fluctuating from 20 851 in 2005 to 20 878 in 2014; however, the cases of operation increased year by year, from 88 in 2005 to 163 in 2014; the average length of stay decreased from 21 in 2005 to 10 in 2014; the total cases of transfusion were 22 from 2005 to 2014; the safety, stability and feasibility of the innovated technologies and products were illustrated through the decrease of average length of stay, the reduction of bleeding and the significance of outcomes. It is illustrated that the innovated technologies and products not only decrease patients' suffering and medical costs but also are safe, stable and feasible.

Nanofiltration technology in water treatment and reuse: applications and costs.

Science.gov (United States)

Shahmansouri, Arash; Bellona, Christopher

2015-01-01

Nanofiltration (NF) is a relatively recent development in membrane technology with characteristics that fall between ultrafiltration and reverse osmosis (RO). While RO membranes dominate the seawater desalination industry, NF is employed in a variety of water and wastewater treatment and industrial applications for the selective removal of ions and organic substances, as well as certain niche seawater desalination applications. The purpose of this study was to review the application of NF membranes in the water and wastewater industry including water softening and color removal, industrial wastewater treatment, water reuse, and desalination. Basic economic analyses were also performed to compare the profitability of using NF membranes over alternative processes. Although any detailed cost estimation is hampered by some uncertainty (e.g. applicability of estimation methods to large-scale systems, labor costs in different areas of the world), NF was found to be a cost-effective technology for certain investigated applications. The selection of NF over other treatment technologies, however, is dependent on several factors including pretreatment requirements, influent water quality, treatment facility capacity, and treatment goals.

Ship Compliance in Emission Control Areas: Technology Costs and Policy Instruments.

Science.gov (United States)

Carr, Edward W; Corbett, James J

2015-08-18

This paper explores whether a Panama Canal Authority pollution tax could be an effective economic instrument to achieve Emission Control Area (ECA)-like reductions in emissions from ships transiting the Panama Canal. This tariff-based policy action, whereby vessels in compliance with International Maritime Organisation (IMO) ECA standards pay a lower transit tariff than noncompliant vessels, could be a feasible alternative to petitioning for a Panamanian ECA through the IMO. A $4.06/container fuel tax could incentivize ECA-compliant emissions reductions for nearly two-thirds of Panama Canal container vessels, mainly through fuel switching; if the vessel(s) also operate in IMO-defined ECAs, exhaust-gas treatment technologies may be cost-effective. The RATES model presented here compares current abatement technologies based on hours of operation within an ECA, computing costs for a container vessel to comply with ECA standards in addition to computing the Canal tax that would reduce emissions in Panama. Retrofitted open-loop scrubbers are cost-effective only for vessels operating within an ECA for more than 4500 h annually. Fuel switching is the least-cost option to industry for vessels that operate mostly outside of ECA regions, whereas vessels operating entirely within an ECA region could reduce compliance cost with exhaust-gas treatment technology (scrubbers).

Distributed utility technology cost, performance, and environmental characteristics

Energy Technology Data Exchange (ETDEWEB)

Wan, Y; Adelman, S

1995-06-01

Distributed Utility (DU) is an emerging concept in which modular generation and storage technologies sited near customer loads in distribution systems and specifically targeted demand-side management programs are used to supplement conventional central station generation plants to meet customer energy service needs. Research has shown that implementation of the DU concept could provide substantial benefits to utilities. This report summarizes the cost, performance, and environmental and siting characteristics of existing and emerging modular generation and storage technologies that are applicable under the DU concept. It is intended to be a practical reference guide for utility planners and engineers seeking information on DU technology options. This work was funded by the Office of Utility Technologies of the US Department of Energy.

Considerations on a Cost Model for High-Field Dipole Arc Magnets for FCC

CERN Document Server

AUTHOR|(CDS)2078700; Durante, Maria; Lorin, Clement; Martinez, Teresa; Ruuskanen, Janne; Salmi, Tiina; Sorbi, Massimo; Tommasini, Davide; Toral, Fernando

2017-01-01

In the frame of the European Circular Collider (EuroCirCol), a conceptual design study for a post-Large Hadron Collider (LHC) research infrastructure based on an energy-frontier 100 TeV circular hadron collider [1]–[3], a cost model for the high-field dipole arc magnets is being developed. The aim of the cost model in the initial design phase is to provide the basis for sound strategic decisions towards cost effective designs, in particular: (A) the technological choice of superconducting material and its cost, (B) the target performance of Nb$_{3}$Sn superconductor, (C) the choice of operating temperature (D) the relevant design margins and their importance for cost, (E) the nature and extent of grading, and (F) the aperture’s influence on cost. Within the EuroCirCol study three design options for the high field dipole arc magnets are under study: cos − θ [4], block [5], and common-coil [6]. Here, in the advanced design phase, a cost model helps to (1) identify the cost drivers and feed-back this info...

Considerations on a Cost Model for High-Field Dipole Arc Magnets for FCC

CERN Document Server

AUTHOR|(CDS)2078700; Durante, Maria; Lorin, Clement; Martinez, Teresa; Ruuskanen, Janne; Salmi, Tiina; Sorbi, Massimo; Tommasini, Davide; Toral, Fernando

2017-01-01

In the frame of the European Circular Collider (EuroCirCol), a conceptual design study for a post-Large Hadron Collider (LHC) research infrastructure based on an energy-frontier 100 TeV circular hadron collider [1]–[3], a cost model for the high-field dipole arc magnets is being developed. The aim of the cost model in the initial design phase is to provide the basis for sound strategic decisions towards cost effective designs, in particular: (A) the technological choice of superconducting material and its cost, (B) the target performance of Nb3Sn superconductor, (C) the choice of operating temperature (D) the relevant design margins and their importance for cost, (E) the nature and extent of grading, and (F) the aperture’s influence on cost. Within the EuroCirCol study three design options for the high field dipole arc magnets are under study: cos − θ [4], block [5], and common-coil [6]. Here, in the advanced design phase, a cost model helps to (1) identify the cost drivers and feed-back this informati...

Compact and cost-effective multi-channel optical spectrometer for fine FBG sensing in IoT technology

Science.gov (United States)

Konishi, Tsuyoshi; Yamasaki, Yu

2018-02-01

Optical fiber sensor networks have attracted much attention in IoT technology and a fiber Bragg grating is one of key sensor devices there because of their advantages in a high affinity for optical fiber networks, compactness, immunity to electromagnetic interference and so on. Nevertheless, its sensitivity is not always satisfactory so as to be usable together with widespread cost-effective multi-channel spectrometers. In this paper, we introduce a new cost-effective approach for a portable multi-channel spectrometer with high spectral resolution and demonstrates some preliminary experimental results for fine FBG sensing.

COST EFFECTIVE AND HIGH RESOLUTION SUBSURFACE CHARACTERIZATION USING HYDRAULIC TOMOGRAPHY

Science.gov (United States)

2017-08-01

objective of this project is to provide the DoD and its remediation contractors with the HT technology for delineating the spatial distribution of...STATEMENT Approved for public release; distribution is unlimited 13. SUPPLEMENTARY NOTES 14. ABSTRACT Hydraulic Tomography ( HT ) is a high-resolution...performance of subsurface remedial actions at environmental sites. The good technical performance and cost-effectiveness of HT have been demonstrated in

The external costs of electricity generation: a comparison of generation technologies

Energy Technology Data Exchange (ETDEWEB)

Ozdemiroglu, E [Economics for the Environment Consultancy, London (United Kingdom)

1995-12-01

Electricity generation, like any economic activity, leads to costs that can be grouped in two categories: (a) private or internal and (b) external. Private costs are those paid by the buyers and sellers of energy within the market system. The external costs, however, are not included in the market price mechanism as they accrue to third parties other than the buyer and the seller. External costs include environmental external costs and non-environmental external costs. There are two conditions for the existence of external costs: (a) market failure, or the inability of markets to account for the cost of environmental impacts of energy generation and the market structure and (b) government or policy failure, or the policies that cause private generators to pay either higher or lower costs than they would if these interventions did not exist. A third reason can be added for the existence of non-environmental externalities: energy security, or certain costs faced by society as a result of over-reliance on imported energy. Section A introduces the concept of external costs and benefits. Section B looks at the environmental externalities of energy generation. The procedure is to develop the methodology to estimate what are known as externality adders, i.e. a monetary value for the environmental costs and benefits associated with selected generation technologies, expressed in pence per kilowatt-hour. The result is an `adder` because, in principle, the sum can be added to the private cost of generating electricity to obtain a measure of the `full` or `social` cost. The selected generation technologies are conventional coal, wind power, small-scale hydro, energy crops, incineration of municipal solid waste and energy recovery from landfill. The data reported are based on the application of the technologies in Scotland, but the methodology can be applied anywhere. Section C takes a brief look at the non-environmental externalities including the general theory and evidence

The external costs of electricity generation: a comparison of generation technologies

International Nuclear Information System (INIS)

Ozdemiroglu, E.

1995-01-01

Electricity generation, like any economic activity, leads to costs that can be grouped in two categories: (a) private or internal and (b) external. Private costs are those paid by the buyers and sellers of energy within the market system. The external costs, however, are not included in the market price mechanism as they accrue to third parties other than the buyer and the seller. External costs include environmental external costs and non-environmental external costs. There are two conditions for the existence of external costs: (a) market failure, or the inability of markets to account for the cost of environmental impacts of energy generation and the market structure and (b) government or policy failure, or the policies that cause private generators to pay either higher or lower costs than they would if these interventions did not exist. A third reason can be added for the existence of non-environmental externalities: energy security, or certain costs faced by society as a result of over-reliance on imported energy. Section A introduces the concept of external costs and benefits. Section B looks at the environmental externalities of energy generation. The procedure is to develop the methodology to estimate what are known as externality adders, i.e. a monetary value for the environmental costs and benefits associated with selected generation technologies, expressed in pence per kilowatt-hour. The result is an 'adder' because, in principle, the sum can be added to the private cost of generating electricity to obtain a measure of the 'full' or 'social' cost. The selected generation technologies are conventional coal, wind power, small-scale hydro, energy crops, incineration of municipal solid waste and energy recovery from landfill. The data reported are based on the application of the technologies in Scotland, but the methodology can be applied anywhere. Section C takes a brief look at the non-environmental externalities including the general theory and evidence

A low-cost, high-resolution, video-rate imaging optical radar

Energy Technology Data Exchange (ETDEWEB)

Sackos, J.T.; Nellums, R.O.; Lebien, S.M.; Diegert, C.F. [Sandia National Labs., Albuquerque, NM (United States); Grantham, J.W.; Monson, T. [Air Force Research Lab., Eglin AFB, FL (United States)

1998-04-01

Sandia National Laboratories has developed a unique type of portable low-cost range imaging optical radar (laser radar or LADAR). This innovative sensor is comprised of an active floodlight scene illuminator and an image intensified CCD camera receiver. It is a solid-state device (no moving parts) that offers significant size, performance, reliability, and simplicity advantages over other types of 3-D imaging sensors. This unique flash LADAR is based on low cost, commercially available hardware, and is well suited for many government and commercial uses. This paper presents an update of Sandia`s development of the Scannerless Range Imager technology and applications, and discusses the progress that has been made in evolving the sensor into a compact, low, cost, high-resolution, video rate Laser Dynamic Range Imager.

A high performance, high precision, low cost rapid prototyping and manufacturing technology

OpenAIRE

Viacheslav R. Shulunov

2014-01-01

A novel roll powder sintering (RPS) technology is proposed for processing real plastic, ceramic, metal and other 3-D objects 1m³ (or more) in volume directly from a CAD model within several hours. The breakthrough advantages of the technology are compared to the dominant rapid prototyping and manufacturing (RP&M) processes that are currently on the market.

CO2 control technology effects on IGCC plant performance and cost

International Nuclear Information System (INIS)

Chen Chao; Rubin, Edward S.

2009-01-01

As part of the USDOE's Carbon Sequestration Program, an integrated modeling framework has been developed to evaluate the performance and cost of alternative carbon capture and storage (CCS) technologies for fossil-fueled power plants in the context of multi-pollutant control requirements. This paper uses the newly developed model of an integrated gasification combined cycle (IGCC) plant to analyze the effects of adding CCS to an IGCC system employing a GE quench gasifier with water gas shift reactors and a Selexol system for CO 2 capture. Parameters of interest include the effects on plant performance and cost of varying the CO 2 removal efficiency, the quality and cost of coal, and selected other factors affecting overall plant performance and cost. The stochastic simulation capability of the model is also used to illustrate the effect of uncertainties or variability in key process and cost parameters. The potential for advanced oxygen production and gas turbine technologies to reduce the cost and environmental impacts of IGCC with CCS is also analyzed

Cost/benefit analysis comparing ex situ treatment technologies for removing carbon tetrachloride from Hanford groundwater

International Nuclear Information System (INIS)

Truex, M.J.; Brown, D.R.; Elliott, D.B.

1993-05-01

Pacific Northwest Laboratory conducted a cost/benefit and performance analysis to compare ex situ technologies that can be used to destroy the carbon tetrachloride (CCl 4 ) in the ground water of Hanford's 200 West Area. The objective of this work was to provide a direct quantitative and qualitative comparison of competing technologies. The technologies examined included a biological system, the Thermochemical Environmental Energy System II (TEES II), and a UV/oxidation system. The factors examined included key system operation parameters, impact on inorganic contaminants in the ground water, and secondary waste production. The cost effectiveness of these destruction technologies was also compared to the cost for an air stripping/granular activated carbon (AS/GAC) system. While the AS/GAC system appeared to be more cost effective at many levels than the CCl 4 destruction technologies, the secondary waste produced by this system may lead to significant cost and/or regulatory problems. The factors with the greatest influence on cost for each destruction technology are as follows: nutrient requirements for both of the biological systems, electricity requirements and the type of unit operations for the TEES II process, and electricity requirements for UV/oxidation

Information system technologies' role in augmenting dermatologists' knowledge of prescription medication costs.

Science.gov (United States)

DeMarco, Sebastian S; Paul, Ravi; Kilpatrick, Russell J

2015-12-01

Despite the recent rising costs of once affordable dermatologic prescription medications, a survey measuring dermatologists' attitudes, beliefs, and knowledge of the cost of drugs they commonly prescribe has not been conducted. Awareness of drug costs is hindered by a lack of access to data about the prices of medicines. No surveys of physicians have addressed this issue by proposing new information system technologies that augment prescription medication price transparency and measuring how receptive physicians are to using these novel solutions in their daily clinical practice. Our research aims to investigate these topics with a survey of physicians in dermatology. Members of the North Carolina Dermatology Association were contacted through their electronic mailing list and asked to take an online survey. The survey asked several questions about dermatologists' attitudes and beliefs about drug costs. To measure their knowledge of prescription medications, the National Average Drug Acquisition Cost was used as an authoritative price that was compared to the survey takers' price estimates of drugs commonly used in dermatology. Physicians' willingness to use four distinct information system technologies that increase drug price transparency was also assessed. Dermatologists believe drug costs are an important factor in patient care and believe access to price information would allow them to provide a higher quality of care. Dermatologists' knowledge of the costs of medicines they commonly prescribe is poor, but they want to utilize information system technologies that increase access to drug pricing information. There is an unmet demand for information system technologies which increase price transparency of medications in dermatology. Physicians and IT professionals have the opportunity to create novel information systems that can be utilized to help guide cost conscious clinical decision making. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Decommissioning of Swedish nuclear power reactors. Technology and costs

International Nuclear Information System (INIS)

1994-06-01

The main topics discussed are planning, technology and costs of decommissioning nuclear power reactors. Oskarshamn-3 (BWR) and Ringhals-4 (PWR) have been used as reference reactors. 29 refs, figs, tabs

Overview: Defense high-level waste technology program

International Nuclear Information System (INIS)

Shupe, M.W.; Turner, D.A.

1987-01-01

Defense high-level waste generated by atomic energy defense activities is stored on an interim basis at three U.S. Department of Energy (DOE) operating locations; the Savannah River Plant in South Carolina, the Hanford Site in Washington, and the Idaho National Engineering Laboratory in Idaho. Responsibility for the permanent disposal of this waste resides with DOE's Office of Defense Waste and Transportation Management. The objective of the Defense High-Level Wast Technology Program is to develop the technology for ending interim storage and achieving permanent disposal of all U.S. defense high-level waste. New and readily retrievable high-level waste are immobilized for disposal in a geologic repository. Other high-level waste will be stabilized in-place if, after completion of the National Environmental Policy Act (NEPA) process, it is determined, on a site-specific basis, that this option is safe, cost effective and environmentally sound. The immediate program focus is on implementing the waste disposal strategy selected in compliance with the NEPA process at Savannah River, while continuing progress toward development of final waste disposal strategies at Hanford and Idaho. This paper presents an overview of the technology development program which supports these waste management activities and an assessment of the impact that recent and anticipated legal and institutional developments are expected to have on the program

Scalable Light Module for Low-Cost, High-Efficiency Light- Emitting Diode Luminaires

Energy Technology Data Exchange (ETDEWEB)

Tarsa, Eric [Cree, Inc., Goleta, CA (United States)

2015-08-31

During this two-year program Cree developed a scalable, modular optical architecture for low-cost, high-efficacy light emitting diode (LED) luminaires. Stated simply, the goal of this architecture was to efficiently and cost-effectively convey light from LEDs (point sources) to broad luminaire surfaces (area sources). By simultaneously developing warm-white LED components and low-cost, scalable optical elements, a high system optical efficiency resulted. To meet program goals, Cree evaluated novel approaches to improve LED component efficacy at high color quality while not sacrificing LED optical efficiency relative to conventional packages. Meanwhile, efficiently coupling light from LEDs into modular optical elements, followed by optimally distributing and extracting this light, were challenges that were addressed via novel optical design coupled with frequent experimental evaluations. Minimizing luminaire bill of materials and assembly costs were two guiding principles for all design work, in the effort to achieve luminaires with significantly lower normalized cost ($/klm) than existing LED fixtures. Chief project accomplishments included the achievement of >150 lm/W warm-white LEDs having primary optics compatible with low-cost modular optical elements. In addition, a prototype Light Module optical efficiency of over 90% was measured, demonstrating the potential of this scalable architecture for ultra-high-efficacy LED luminaires. Since the project ended, Cree has continued to evaluate optical element fabrication and assembly methods in an effort to rapidly transfer this scalable, cost-effective technology to Cree production development groups. The Light Module concept is likely to make a strong contribution to the development of new cost-effective, high-efficacy luminaries, thereby accelerating widespread adoption of energy-saving SSL in the U.S.

Development of technology for thin substrate polycrystalline solar cells for practical use. Development of manufacturing technologies for low-cost substrates (low-cost Si substrates); Usugata takessho taiyo denchi seizo gijutsu no jitsuyoka kenkyu. Tei cost kiban seizo gijutsu kaihatsu (usugata takessho kigan seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

This paper reports the study results on manufacturing technologies for low-cost high-quality Si substrates in fiscal 1994. (1) On the 220mm square type electromagnetic casting technology, development of fast stable casting technology was studied using the previously installed 220mm square type electromagnetic casting furnace. As a result, continuous stable casting was achieved at high casting speed up to 3.0mm/min. Any degradation of crystalline quality due to high speed casting was not found. (2) On the 350mm square type electromagnetic casting furnace, oscillation circuit constants were analyzed for design of the power source for No.4 electromagnetic casting furnace. In graphite heating experiment using the 350mm square type water-cooling copper crucible heated by 1000kW high-frequency power source, sufficient heat quantity was obtained for initial melting of Si. Any problems in Si melting were not found through Al block melting test. 6 figs.

The role of information technology (IT) in reducing offshore operating costs

International Nuclear Information System (INIS)

Stern, M.J.

1993-01-01

The rapid changes in information technology (IT) and its application have helped to improve efficiency and reduce operating costs offshore. Developments in IT itself, in terms of technology, organization and standards together with cultural change have created new opportunities. In the application of IT, the most significant impact on operations costs and effectiveness has come from the use of information throughout the life cycle, and improved telecommunications. This paper describes recent developments in IT and its application, and cites examples where oil companies have derived major benefits

What Do Information Technology Support Services Really Cost?

Science.gov (United States)

Leach, Karen; Smallen, David

1998-01-01

A study examined the cost of information-technology support services in higher education institutions. The report describes the project's origins and work to date and reports initial results in three areas: network services, desktop repair services, and administrative information systems, looking in each case at economies of scale, outsourcing…

Appraising the Cost Efficiency of Higher Technological and Vocational Education Institutions in Taiwan Using the Metafrontier Cost-Function Model

Science.gov (United States)

Lu, Yung-Hsiang; Chen, Ku-Hsieh

2013-01-01

This paper aims at appraising the cost efficiency and technology of institutions of higher technological and vocational education. Differing from conventional literature, it considers the potential influence of inherent discrepancies in output quality and characteristics of school systems for institutes of technology (ITs) and universities of…

Physics and high technology

International Nuclear Information System (INIS)

Shao Liqin; Ma Junru.

1992-01-01

At present, the development of high technology has opened a new chapter in world's history of science and technology. This review describes the great impact of physics on high technology in six different fields (energy technology, new materials, information technology, biotechnology, space technology, and Ocean technology). It is shown that the new concepts and new methods created in physics and the special conditions and measurements established for physics researches not only deepen human's knowledge about nature but also point out new directions for engineering and technology. The achievements in physics have been more and more applied to high technology, while the development of high technology has explored some new research areas and raised many novel, important projects for physics. Therefore, it is important for us to strengthen the research on these major problems in physics

Novel Low Cost Organic Vapor Jet Printing of Striped High Efficiency Phosphorescent OLEDs for White Lighting

Energy Technology Data Exchange (ETDEWEB)

Mike Hack

2008-12-31

In this program, Universal Display Corporation and University of Michigan proposed to integrate three innovative concepts to meet the DOE's Solid State Lighting (SSL) goals: (1) high-efficiency phosphorescent organic light emitting device (PHOLED{trademark}) technology, (2) a white lighting design that is based on a series of red, green and blue OLED stripes, and (3) the use of a novel cost-effective, high rate, mask-less deposition process called organic vapor jet printing (OVJP). Our PHOLED technology offers up to four-times higher power efficiency than other OLED approaches for general lighting. We believe that one of the most promising approaches to maximizing the efficiency of OLED lighting sources is to produce stripes of the three primary colors at such a pitch (200-500 {mu}m) that they appear as a uniform white light to an observer greater than 1 meter (m) away from the illumination source. Earlier work from a SBIR Phase 1 entitled 'White Illumination Sources Using Striped Phosphorescent OLEDs' suggests that stripe widths of less than 500 {mu}m appear uniform from a distance of 1m without the need for an external diffuser. In this program, we intend to combine continued advances in this PHOLED technology with the striped RGB lighting design to demonstrate a high-efficiency, white lighting source. Using this background technology, the team has focused on developing and demonstrating the novel cost-effective OVJP process to fabricate these high-efficiency white PHOLED light sources. Because this groundbreaking OVJP process is a direct printing approach that enables the OLED stripes to be printed without a shadow mask, OVJP offers very high material utilization and high throughput without the costs and wastage associated with a shadow mask (i.e. the waste of material that deposits on the shadow mask itself). As a direct printing technique, OVJP also has the potential to offer ultra-high deposition rates (> 1,000 Angstroms/second) for any size or

Transforming Learning through Technology: Educating More, Costing Less

Science.gov (United States)

Twigg, Carol A.

2011-01-01

Face-to-face instruction has been held as the gold standard of a quality academic program. But using information technology to redesign traditional courses can actually improve the quality of teaching, cut costs, and improve access and success. A strong redesign often involves active learning opportunities; individualized, on-demand assistance; a…

CO{sub 2} mitigation costs of large-scale bioenergy technologies in competitive electricity markets

Energy Technology Data Exchange (ETDEWEB)

Gustavsson, L [Mid-Sweden University, Ostersund (Sweden). Dept. of Natural and Environmental Sciences, Ecotechnology; Madlener, R [Swiss Federal Institute of Technology, Zurich (Switzerland). CEPE

2003-11-01

In this study, we compare and contrast the impact of recent technological developments in large biomass-fired and natural-gas-fired cogeneration and condensing plants in terms of CO{sub 2} mitigation costs and under the conditions of a competitive electricity market. The CO{sub 2} mitigation cost indicates the minimum economic incentive required (e.g. in the form of a carbon tax) to equal the cost of a less carbon extensive system with the cost of a reference system. The results show that CO{sub 2} mitigation costs are lower for biomass systems than for natural gas systems with decarbonization. However, in liberalized energy markets and given the sociopolitical will to implement carbon extensive energy systems, market-based policy measures are still required to make biomass and decarbonization options competitive and thus help them to penetrate the market. This cost of cogeneration plants, however, depends on the evaluation method used. If we account for the limitation of heat sinks by expanding the reference entity to include both heat and power, as is typically recommended in life-cycle analysis, then the biomass-based gasification combined cycle (BIG/CC) technology turns out to be less expensive and to exhibit lower CO{sub 2} mitigation costs than biomass-fired steam turbine plants. However, a heat credit granted to cogeneration systems that is based on avoided cost of separate heat production, puts the steam turbine technology despite its lower system efficiency at an advantage. In contrast, when a crediting method based on avoided electricity production in natural gas fired condensing plants is employed, the BIG/CC technology turns out to be more cost competitive than the steam turbine technology for carbon tax levels beyond about $150/t C. Furthermore, steam turbine plants are able to compete with natural gas fired cogeneration plants at carbon tax levels higher than about $90/tC. (author)

Technology readiness levels and technology status for selected long term/high payoff technologies on the RLV program

Science.gov (United States)

Rosmait, Russell L.

1996-01-01

The development of a new space transportation system in a climate of constant budget cuts and staff reductions can be and is a difficult task. It is no secret that NASA's current launching system consumes a very large portion of NASA funding and requires a large army of people to operate & maintain the system. The new Reusable Launch Vehicle (RLV) project and it's programs are faced with a monumental task of making the cost of access to space dramatically lower and more efficient than NASA's current system. With pressures from congressional budget cutters and also increased competition and loss of market share from international agencies RLV's first priority is to develop a 'low-cost, reliable transportation to earth orbit.' One of the RLV's major focus in achieving low-cost, reliable transportation to earth orbit is to rely on the maturing of advanced technologies. The technologies for the RLV are numerous and varied. Trying to assess their current status, within the RLV development program is paramount. There are several ways to assess these technologies. One way is through the use of Technology Readiness Levels (TRL's). This project focused on establishing current (summer 95) 'worst case' TRL's for six selected technologies that are under consideration for use within the RLV program. The six technologies evaluated were Concurrent Engineering, Embedded Sensor Technology, Rapid Prototyping, Friction Stir Welding, Thermal Spray Coatings, and VPPA Welding.

New technology adoption for Russian energy generation: What does it cost? A case study for Moscow

International Nuclear Information System (INIS)

Bratanova, Alexandra; Robinson, Jacqueline; Wagner, Liam

2016-01-01

Highlights: • Power generation cost is modelled for a Russian region under two gas price scenarios. • Conventional, new and renewable technologies are compared based on levelised cost. • Regional energy system is shown to be crucially dependent on natural gas prices. • We conclude that new gas-fired technology adoption is feasible and cost-competitive. • Biomass demonstrates cost competitiveness, whereas solar appears infeasible. - Abstract: Russia is frequently referred to as a country with substantial energy efficiency and renewable energy potential. In 2000–2008 energy-gross domestic product (GDP) ratios were improved by 35%, however, the contribution of technological progress accounts for only 1% of the energy-GDP ratio reduction. At the same time, although new policy mechanisms to stimulate renewable energy development have been recently introduced, renewable technology deployment has not yet taken off. Economic theory suggests that there is no better incentive for industry development than cost signals. This paper adapts the levelised cost of energy methodology to examine the cost structures associated with electricity generation by conventional and new technology types for a Russian region (Moscow). The model, run for two fuel price scenarios, allowed us to conclude that the regional energy supply system is heavily dependent on the natural gas price and that the diversification provided by technology development will be beneficial for the energy security of the region. We conclude that new and renewable technologies become cost-effective for electricity generation as domestic natural gas prices reach parity with export prices. However, strong political and financial support is needed to boost technological development and renewables application in Russia.

Selected bibliography: cost and energy savings of conservation and renewable energy technologies

Energy Technology Data Exchange (ETDEWEB)

None

1980-05-01

This bibliography is a compilation of reports on the cost and energy savings of conservation and renewable energy applications throughout the United States. It is part of an overall effort to inform utilities of technological developments in conservation and renewable energy technologies and so aid utilities in their planning process to determine the most effective and economic combination of capital investments to meet customer needs. Department of Energy assessments of the applications, current costs and cost goals for the various technologies included in this bibliography are presented. These assessments are based on analyses performed by or for the respective DOE Program Offices. The results are sensitive to a number of variables and assumptions; however, the estimates presented are considered representative. These assessments are presented, followed by some conclusions regarding the potential role of the conservation and renewable energy alternative. The approach used to classify the bibliographic citations and abstracts is outlined.

Low-cost bump-bonding processes for high energy physics pixel detectors

CERN Document Server

AUTHOR|(CDS)2069357; Blank, Thomas; Colombo, Fabio; Dierlamm, Alexander Hermann; Husemann, Ulrich; Kudella, Simon; Weber, M

2016-01-01

In the next generation of collider experiments detectors will be challenged by unprecedented particle fluxes. Thus large detector arrays of highly pixelated detectors with minimal dead area will be required at reasonable costs. Bump-bonding of pixel detectors has been shown to be a major cost-driver. KIT is one of five production centers of the CMS barrel pixel detector for the Phase I Upgrade. In this contribution the SnPb bump-bonding process and the production yield is reported. In parallel to the production of the new CMS pixel detector, several alternatives to the expensive photolithography electroplating/electroless metal deposition technologies are developing. Recent progress and challenges faced in the development of bump-bonding technology based on gold-stud bonding by thin (15 μm) gold wire is presented. This technique allows producing metal bumps with diameters down to 30 μm without using photolithography processes, which are typically required to provide suitable under bump metallization. The sh...

Cost studies of thermally enhanced in situ soil remediation technologies

International Nuclear Information System (INIS)

Bremser, J.; Booth, S.R.

1996-05-01

This report describes five thermally enhanced technologies that may be used to remediate contaminated soil and water resources. The standard methods of treating these contaminated areas are Soil Vapor Extraction (SVE), Excavate ampersand Treat (E ampersand T), and Pump ampersand Treat (P ampersand T). Depending on the conditions at a given site, one or more of these conventional alternatives may be employed; however, several new thermally enhanced technologies for soil decontamination are emerging. These technologies are still in demonstration programs which generally are showing great success at achieving the expected remediation results. The cost savings reported in this work assume that the technologies will ultimately perform as anticipated by their developers in a normal environmental restoration work environment. The five technologies analyzed in this report are Low Frequency Heating (LF or Ohmic, both 3 and 6 phase AC), Dynamic Underground Stripping (DUS), Radio Frequency Heating (RF), Radio Frequency Heating using Dipole Antennae (RFD), and Thermally Enhanced Vapor Extraction System (TEVES). In all of these technologies the introduction of heat to the formation raises vapor pressures accelerating contaminant evaporation rates and increases soil permeability raising diffusion rates of contaminants. The physical process enhancements resulting from temperature elevations permit a greater percentage of volatile organic compound (VOC) or semi- volatile organic compound (SVOC) contaminants to be driven out of the soils for treatment or capture in a much shorter time period. This report presents the results of cost-comparative studies between these new thermally enhanced technologies and the conventional technologies, as applied to five specific scenarios

Low cost construction technologies and materials - case study Mozambuique

CSIR Research Space (South Africa)

Kuchena, JC

2009-09-01

Full Text Available Low cost or affordable construction technologies and materials are often touted as a panacea in meeting the ever growing demand for rapid housing delivery in developing economies. Mozambique as with most of the developing world, from both historical...

Smarter elder care? A cost-effectiveness analysis of implementing technology in elder care.

Science.gov (United States)

Aanesen, Margrethe; Lotherington, Ann Therese; Olsen, Frank

2011-09-01

Whereas in most sectors, technology has taken over trivial and labour consuming tasks, this transformation has been delayed in the healthcare sector. Although appropriate technology is available, there is general resistance to substituting 'warm' hands with 'cold' technology. In the future, this may change as the number of elderly people increases relative to the people in the work force. In combination with an increasing demand for healthcare services, there are calls for efforts to increase productivity in the sector. Based on experience data from previous studies on information and communication technology efforts in the healthcare sector, we quantitatively assess the use of smart house technology and video visits in home care. Having identified healthcare providers, hospitals and relatives as the main affected groups, we show that smart house technology is cost-effective, even if only relatives gain from it. Video visits, which have higher implementation costs, demand effects on both relatives and health care providers in order to be a cost-effective tool in home care. As the analysis is purely quantitative, these results need to be complemented with qualitative effects and with more thorough discussions of the ethical, medical and legal aspects of the use of technology in home care.

Technological Minimalism: A Cost-Effective Alternative for Course Design and Development.

Science.gov (United States)

Lorenzo, George

2001-01-01

Discusses the use of minimum levels of technology, or technological minimalism, for Web-based multimedia course content. Highlights include cost effectiveness; problems with video streaming, the use of XML for Web pages, and Flash and Java applets; listservs instead of proprietary software; and proper faculty training. (LRW)

A DDC Bibliography on Cost/Benefits of Technical Information Services and Technology Transfer.

Science.gov (United States)

Defense Documentation Center, Alexandria, VA.

This bibliography is a compilation of literature existing in both the government and public sectors and concerning Cost/Benefits of Technical information Services and Technology Transfer. Not only was the cost-benefit to the user reflected, but consideration was given to the initial cost of information collections, the cost of processing the…

Re-Engineering a High Performance Electrical Series Elastic Actuator for Low-Cost Industrial Applications

Directory of Open Access Journals (Sweden)

Kenan Isik

2017-01-01

Full Text Available Cost is an important consideration when transferring a technology from research to industrial and educational use. In this paper, we introduce the design of an industrial grade series elastic actuator (SEA performed via re-engineering a research grade version of it. Cost-constrained design requires careful consideration of the key performance parameters for an optimal performance-to-cost component selection. To optimize the performance of the new design, we started by matching the capabilities of a high-performance SEA while cutting down its production cost significantly. Our posit was that performing a re-engineering design process on an existing high-end device will significantly reduce the cost without compromising the performance drastically. As a case study of design for manufacturability, we selected the University of Texas Series Elastic Actuator (UT-SEA, a high-performance SEA, for its high power density, compact design, high efficiency and high speed properties. We partnered with an industrial corporation in China to research the best pricing options and to exploit the retail and production facilities provided by the Shenzhen region. We succeeded in producing a low-cost industrial grade actuator at one-third of the cost of the original device by re-engineering the UT-SEA with commercial off-the-shelf components and reducing the number of custom-made parts. Subsequently, we conducted performance tests to demonstrate that the re-engineered product achieves the same high-performance specifications found in the original device. With this paper, we aim to raise awareness in the robotics community on the possibility of low-cost realization of low-volume, high performance, industrial grade research and education hardware.

A study of the cost-effective markets for new technology agricultural aircraft

Science.gov (United States)

Hazelrigg, G. A., Jr.; Clyne, F.

1979-01-01

A previously developed data base was used to estimate the regional and total U.S. cost-effective markets for a new technology agricultural aircraft as incorporating features which could result from NASA-sponsored aerial applications research. The results show that the long-term market penetration of a new technology aircraft would be near 3,000 aircraft. This market penetration would be attained in approximately 20 years. Annual sales would be about 200 aircraft after 5 to 6 years of introduction. The net present value of cost savings benefit which this aircraft would yield (measured on an infinite horizon basis) would be about $35 million counted at a 10 percent discount rate and $120 million at a 5 percent discount rate. At both discount rates the present value of cost savings exceeds the present value of research and development (R&D) costs estimated for the development of the technology base needed for the proposed aircraft. These results are quite conservative as they have been derived neglecting future growth in the agricultural aviation industry, which has been averaging about 12 percent per year over the past several years.

Is Myomectomy Prior to Assisted Reproductive Technology Cost Effective in Women with Intramural Fibroids?

Science.gov (United States)

Ojo-Carons, Mary; Mumford, Sunni L; Armstrong, Alicia Y; DeCherney, Alan H; Devine, Kate

2016-01-01

To evaluate the cost effectiveness of surgery to remove intramural (IM) fibroids prior to assisted reproductive technology (ART). The decision tree mathematical model along with sensitivity analysis was performed to analyze cost effectiveness of: (1) myomectomy followed by ART or (2) ART with IM myoma(s) in situ. At the median ongoing pregnancy (OP) rate (OPR) reported in the literature for a fresh, autologous ART cycle with IM fibroids in situ vs. post-IM myomectomy, average cost per OP was $72,355 vs. 66,075, indicating a cost savings with myomectomy. Sensitivity analysis over the range of reported OPRs demonstrated that pre-ART IM myomectomy was always cost effective when OPR among women with in situ myomas was ART IM myomectomy was only cost effective if it increased OPR by at least 9.6%. At the high end of OPRs reported for patients with IM myomas in situ (31.4%), a 19.5% improvement in OPR was needed to justify IM myomectomy from a cost perspective. Myomectomy should be used sparingly in cases where the goal of surgery is to achieve improvement in the outcomes of ART. © 2016 S. Karger AG, Basel.

Cost-effective backhaul design using hybrid radio/free-space optical technology

KAUST Repository

Douik, Ahmed S.

2015-06-08

The deluge of date rate in today\\'s networks poses a cost burden on the backhaul network design. Developing cost efficient backhaul solutions becomes an interesting, yet challenging, problem. Traditional technologies for backhaul networks include either radio-frequency backhauls (RF) or optical fibres (OF). While RF is a cost-effective solution as compared to OF, it supports lower data rate requirements. Another promising backhaul solution that may combine both a high data rate and a relatively low cost is the free-space optics (FSO). FSO, however, is sensitive to nature conditions (e.g., rain, fog, line-ofsight, etc.). A more reliable alternative is, therefore, to combine RF and FSO solutions through a hybrid structure called hybrid RF/FSO. Consider a backhaul network, where the base-stations (BS) can be connected to each other either via OF or hybrid RF/FSO backhaul links. The paper addresses the problem of minimizing the cost of backhaul planning under connectivity and data rates constraints, so as to choose the appropriate costeffective backhaul type between BSs (i.e., either OF or hybrid RF/FSO). The paper solves the problem using graph theory techniques by introducing the corresponding planning graph. It shows that under a specified realistic assumption about the cost of OF and hybrid RF/FSO links, the problem is equivalent to a maximum weight clique problem, which can be solved with moderate complexity. Simulation results show that our proposed solution shows a close-to-optimal performance, especially for practical prices of the hybrid RF/FSO.

Cost-effective backhaul design using hybrid radio/free-space optical technology

KAUST Repository

Douik, Ahmed S.; Dahrouj, Hayssam; Al-Naffouri, Tareq Y.; Alouini, Mohamed-Slim

2015-01-01

The deluge of date rate in today's networks poses a cost burden on the backhaul network design. Developing cost efficient backhaul solutions becomes an interesting, yet challenging, problem. Traditional technologies for backhaul networks include either radio-frequency backhauls (RF) or optical fibres (OF). While RF is a cost-effective solution as compared to OF, it supports lower data rate requirements. Another promising backhaul solution that may combine both a high data rate and a relatively low cost is the free-space optics (FSO). FSO, however, is sensitive to nature conditions (e.g., rain, fog, line-ofsight, etc.). A more reliable alternative is, therefore, to combine RF and FSO solutions through a hybrid structure called hybrid RF/FSO. Consider a backhaul network, where the base-stations (BS) can be connected to each other either via OF or hybrid RF/FSO backhaul links. The paper addresses the problem of minimizing the cost of backhaul planning under connectivity and data rates constraints, so as to choose the appropriate costeffective backhaul type between BSs (i.e., either OF or hybrid RF/FSO). The paper solves the problem using graph theory techniques by introducing the corresponding planning graph. It shows that under a specified realistic assumption about the cost of OF and hybrid RF/FSO links, the problem is equivalent to a maximum weight clique problem, which can be solved with moderate complexity. Simulation results show that our proposed solution shows a close-to-optimal performance, especially for practical prices of the hybrid RF/FSO.

High Efficiency Low Cost CO2 Compression Using Supersonic Shock Wave Technology

Energy Technology Data Exchange (ETDEWEB)

Williams, J; Aarnio, M; Grosvenor, A; Taylor, D; Bucher, J

2010-12-31

Development and testing results from a supersonic compressor are presented. The compressor achieved record pressure ratio for a fully-supersonic stage and successfully demonstrated the technology potential. Several tasks were performed in compliance with the DOE award objectives. A high-pressure ratio compressor was retrofitted to improve rotordynamics behavior and successfully tested. An outside review panel confirmed test results and design approach. A computational fluid dynamics code used to analyze the Ramgen supersonic flowpath was extensively and successfully modified to improve use on high-performance computing platforms. A comprehensive R&D implementation plan was developed and used to lay the groundwork for a future full-scale compressor demonstration. Conceptual design for a CO2 demonstration compressor was developed and reviewed.

Production Costs of Alternative Transportation Fuels. Influence of Crude Oil Price and Technology Maturity

Energy Technology Data Exchange (ETDEWEB)

Cazzola, Pierpaolo; Morrison, Geoff; Kaneko, Hiroyuki; Cuenot, Francois; Ghandi, Abbas; Fulton, Lewis

2013-07-01

This study examines the production costs of a range of transport fuels and energy carriers under varying crude oil price assumptions and technology market maturation levels. An engineering ''bottom-up'' approach is used to estimate the effect of the input cost of oil and of various technological assumptions on the finished price of these fuels. In total, the production costs of 20 fuels are examined for crude oil prices between USD 60 and USD 150 per barrel. Some fuel pathways can be competitive with oil as their production, transport and storage technology matures, and as oil price increases. Rising oil prices will offer new opportunities to switch to alternative fuels for transport, to diversify the energy mix of the transport sector, and to reduce the exposure of the whole system to price volatility and potential distuption of supply. In a time of uncertainty about the leading vehicle technology to decarbonize the transport sector, looking at the fuel cost brings key information to be considered to keep mobility affordable yet sustainable.

Electricity and fluid fuels from biomass and coal using advanced technologies: a cost comparison for developing country applications

Energy Technology Data Exchange (ETDEWEB)

Kartha, S; Larson, E D; Williams, R H [Center for Energy and Environment Studies School of Engineering and Applied Science, Princeton University, Princeton, NJ (United States); Katofsky, R E [Arthur D. Little Co., Cambridge, MA (United States); Chen, J [Thermo Fibertek, Inc., Auburn, MA (United States); Marrison, C I [Oliver, Wyman and Co., New York, NY (United States)

1995-12-01

Recent analyses of alternative global energy supply strategies, such as the forthcoming report of the Intergovernmental Panel on Climate Change (IPCC), to be published in 1996, have drawn attention to the possibility that biomass modernized with advanced technologies could play an important role in meeting global energy needs in the next century. This paper discusses two promising classes of advanced technologies that offer the potential for providing modem energy carriers (electricity and fluid fuels) from biomass at competitive costs within one or two decades. These technologies offer significantly more efficient use of land than currently commercial technologies for producing electricity and fluid fuels from biomass, as well as substantially improved energy balances. Electricity is Rely to be the first large market for modernized biomass, but the potential market for fluid fuel production is likely to be much larger. As coal is likely to present a more serious competitive challenge to biomass in the long run, we present an economic comparison with coal-based electricity and fluid fuels. A meaningful economic comparison between coal and biomass is possible because these feedstocks are sufficiently alike in their physical characteristics that similar conversion technologies may well be used for producing electricity and fluid fuels from them. When similar conversion technologies are used for both feedstocks, the relative costs of electricity or fluid fuels will be determined by the distinguishing technical characteristics of the feedstocks (sulphur content, moisture content and reactivity) and by the relative feedstock prices. Electric power generation from biomass and coal are compared here using an advanced integrated gasifier/gas turbine cycle that offers the potential for achieving high efficiency, low unit capital cost and low local pollutant emissions: the steam-injected gas turbine coupled to an air-blown gasifier. For both feedstocks, generation costs are

Electricity and fluid fuels from biomass and coal using advanced technologies: a cost comparison for developing country applications

International Nuclear Information System (INIS)

Kartha, S.; Larson, E.D.; Williams, R.H.; Katofsky, R.E.; Chen, J.; Marrison, C.I.

1995-01-01

Recent analyses of alternative global energy supply strategies, such as the forthcoming report of the Intergovernmental Panel on Climate Change (IPCC), to be published in 1996, have drawn attention to the possibility that biomass modernized with advanced technologies could play an important role in meeting global energy needs in the next century. This paper discusses two promising classes of advanced technologies that offer the potential for providing modem energy carriers (electricity and fluid fuels) from biomass at competitive costs within one or two decades. These technologies offer significantly more efficient use of land than currently commercial technologies for producing electricity and fluid fuels from biomass, as well as substantially improved energy balances. Electricity is Rely to be the first large market for modernized biomass, but the potential market for fluid fuel production is likely to be much larger. As coal is likely to present a more serious competitive challenge to biomass in the long run, we present an economic comparison with coal-based electricity and fluid fuels. A meaningful economic comparison between coal and biomass is possible because these feedstocks are sufficiently alike in their physical characteristics that similar conversion technologies may well be used for producing electricity and fluid fuels from them. When similar conversion technologies are used for both feedstocks, the relative costs of electricity or fluid fuels will be determined by the distinguishing technical characteristics of the feedstocks (sulphur content, moisture content and reactivity) and by the relative feedstock prices. Electric power generation from biomass and coal are compared here using an advanced integrated gasifier/gas turbine cycle that offers the potential for achieving high efficiency, low unit capital cost and low local pollutant emissions: the steam-injected gas turbine coupled to an air-blown gasifier. For both feedstocks, generation costs are

The application of the high throughput sequencing technology in the transposable elements.

Science.gov (United States)

Liu, Zhen; Xu, Jian-hong

2015-09-01

High throughput sequencing technology has dramatically improved the efficiency of DNA sequencing, and decreased the costs to a great extent. Meanwhile, this technology usually has advantages of better specificity, higher sensitivity and accuracy. Therefore, it has been applied to the research on genetic variations, transcriptomics and epigenomics. Recently, this technology has been widely employed in the studies of transposable elements and has achieved fruitful results. In this review, we summarize the application of high throughput sequencing technology in the fields of transposable elements, including the estimation of transposon content, preference of target sites and distribution, insertion polymorphism and population frequency, identification of rare copies, transposon horizontal transfers as well as transposon tagging. We also briefly introduce the major common sequencing strategies and algorithms, their advantages and disadvantages, and the corresponding solutions. Finally, we envision the developing trends of high throughput sequencing technology, especially the third generation sequencing technology, and its application in transposon studies in the future, hopefully providing a comprehensive understanding and reference for related scientific researchers.

Quantifying the benefits: Energy, cost, and employment impacts of advanced industrial technologies

International Nuclear Information System (INIS)

Sullivan, G.P.; Roop, J.M.; Schultz, R.W.

1997-01-01

This development effort was supported by the Technologies Partnerships Program established through the US Department of Energy's Office of Energy Efficiency and Renewable Energy via the Office of Industrial Technology (OIT). This program supports research, development, and demonstration of industrial technologies aimed at improving energy efficiency and productivity while reducing pollution, material waste, and operations/maintenance costs. The goal of this program is to develop cost-shared partnerships with industry, government and non-government organizations to foster improved efficiency, productivity, and pollution prevention technologies. This partnership program is believed to be one way that energy efficiency will be delivered to industry in the 21st Century. This paper reports on the development of the Industrial Technology Employment Analysis Model (ITEAM) which calculates economy-wide employment impacts of specific partnership program technologies, using data developed by the technology partner. ITEAM is a desk-top computer model that allows users to evaluate base-case partnership data and/or run sensitivity tests using its graphical-user-interface features. To demonstrate the capabilities of ITEAM, an analysis is presented for the chemicals industry. In addition, the following major industries have been analyzed and summary data are presented: aluminum, stone/clay/glass, forest products, chemicals, metal casting, steel, and petroleum. This paper addresses the development, function, and use of ITEAM. Included is a presentation of key assumptions along with user inputs and a discussion of sensitivities. The results of ITEAM runs for over 20 technology projects in 7 program areas are reported. The paper also explains how the project data are used to modify the 1987 I/O table to impact output and employment. The calculations are explained and the approach is rationalized. The argument for this approach rests on the proposition that improvements in efficiency

High energy beam manufacturing technologies

International Nuclear Information System (INIS)

Geskin, E.S.; Leu, M.C.

1989-01-01

Technological progress continues to enable us to utilize ever widening ranges of physical and chemical conditions for material processing. The increasing cost of energy, raw materials and environmental control make implementation of advanced technologies inevitable. One of the principal avenues in the development of material processing is the increase of the intensity, accuracy, flexibility and stability of energy flow to the processing site. The use of different forms of energy beams is an effective way to meet these sometimes incompatible requirements. The first important technological applications of high energy beams were welding and flame cutting. Subsequently a number of different kinds of beams have been used to solve different problems of part geometry control and improvement of surface characteristics. Properties and applications of different specific beams were subjects of a number of fundamental studies. It is important now to develop a generic theory of beam based manufacturing. The creation of a theory dealing with general principles of beam generation and beam-material interaction will enhance manufacturing science as well as practice. For example, such a theory will provide a format approach for selection and integration of different kinds of beams for a particular application. And obviously, this theory will enable us to integrate the knowledge bases of different manufacturing technologies. The War of the Worlds by H. G. Wells, as well as a number of more technical, although less exciting, publications demonstrate both the feasibility and effectiveness of the generic approach to the description of beam oriented technology. Without any attempt to compete with Wells, we still hope that this volume will contribute to the creation of the theory of beam oriented manufacturing

Programmable Ultra Lightweight System Adaptable Radio (PULSAR) Low Cost Telemetry - Access from Space Advanced Technologies or Down the Middle

Science.gov (United States)

Sims. Herb; Varnavas, Kosta; Eberly, Eric

2013-01-01

Software Defined Radio (SDR) technology has been proven in the commercial sector since the early 1990's. Today's rapid advancement in mobile telephone reliability and power management capabilities exemplifies the effectiveness of the SDR technology for the modern communications market. In contrast, presently qualified satellite transponder applications were developed during the early 1960's space program. Programmable Ultra Lightweight System Adaptable Radio (PULSAR, NASA-MSFC SDR) technology revolutionizes satellite transponder technology by increasing data through-put capability by, at least, an order of magnitude. PULSAR leverages existing Marshall Space Flight Center SDR designs and commercially enhanced capabilities to provide a path to a radiation tolerant SDR transponder. These innovations will (1) reduce the cost of NASA Low Earth Orbit (LEO) and Deep Space transponders, (2) decrease power requirements, and (3) a commensurate volume reduction. Also, PULSAR increases flexibility to implement multiple transponder types by utilizing the same hardware with altered logic - no analog hardware change is required - all of which can be accomplished in orbit. This provides high capability, low cost, transponders to programs of all sizes. The final project outcome would be the introduction of a Technology Readiness Level (TRL) 7 low-cost CubeSat to SmallSat telemetry system into the NASA Portfolio.

Technology Cost and Schedule Estimation (TCASE) Final Report

Science.gov (United States)

Wallace, Jon; Schaffer, Mark

2015-01-01

During the 2014-2015 project year, the focus of the TCASE project has shifted from collection of historical data from many sources to securing a data pipeline between TCASE and NASA's widely used TechPort system. TCASE v1.0 implements a data import solution that was achievable within the project scope, while still providing the basis for a long-term ability to keep TCASE in sync with TechPort. Conclusion: TCASE data quantity is adequate and the established data pipeline will enable future growth. Data quality is now highly dependent the quality of data in TechPort. Recommendation: Technology development organizations within NASA should continue to work closely with project/program data tracking and archiving efforts (e.g. TechPort) to ensure that the right data is being captured at the appropriate quality level. TCASE would greatly benefit, for example, if project cost/budget information was included in TechPort in the future.

Sustainable Technologies and Social Costs for Eliminating Contamination of an Aquifer

Directory of Open Access Journals (Sweden)

Mario Schirmer

2010-07-01

Full Text Available This case study deals with long-term contamination of the Leuna aquifer, which is intended to be restored using sustainable technologies financed by the state. The contamination can only be solved using active rather than passive intervention, because the aquifer has an extraordinarily low natural attenuation capacity for the specific pollutants. Due to the longevity of the contamination source, the groundwater treatment technology that was chosen for the site must operate for a minimum of 20 years but probably much longer. Since the polluter-pay principle cannot be applied, the estimated dynamic primary remediation costs must be accepted as a political or social cost, which must be paid by current and future generations.

Network for development of electroporation-based technologies and treatments: COST TD1104.

Science.gov (United States)

Miklavčič, Damijan

2012-10-01

Exposure of biological cells to a sufficiently strong external electric field results in increased permeability of cell membranes, referred to as "electroporation." Since all types of cells (animal, plant and microorganism) can be effectively electroporated, electroporation is considered to be a universal method and a platform technology. Electroporation has become a widely used technology applicable to, e.g., cancer treatment, gene transfection, food and biomass processing and microbial inactivation. However, despite significant progress in electroporation-based applications, there is a lack of coordination and interdisciplinary exchange of knowledge between researchers from different scientific domains. Thus, critical mass for new major breakthroughs is missing. This is why we decided to establish cooperation between research groups working in different fields of electroporation. Cooperation in Science and Technology (COST), which funds networking and capacity-building activities, presents a perfect framework for such scientific cooperation. This COST action aims at (1) providing necessary steps toward EU cooperation of science and technology to foster basic understanding of electroporation; (2) improving communication between research groups, resulting in streamlining European research and development activities; and (3) enabling development of new and further development of existing electroporation-based applications by integrating multidisciplinary research teams, as well as providing comprehensive training for early-stage researchers. Results of this COST action will provide multiple societal, scientific and technological benefits from improving existing electroporation-based applications to adding new ones in the fields of medicine, biotechnology and environmental preservation.

Photovoltaic technologies

International Nuclear Information System (INIS)

Bagnall, Darren M.; Boreland, Matt

2008-01-01

Photovoltaics is already a billion dollar industry. It is experiencing rapid growth as concerns over fuel supplies and carbon emissions mean that governments and individuals are increasingly prepared to ignore its current high costs. It will become truly mainstream when its costs are comparable to other energy sources. At the moment, it is around four times too expensive for competitive commercial production. Three generations of photovoltaics have been envisaged that will take solar power into the mainstream. Currently, photovoltaic production is 90% first-generation and is based on silicon wafers. These devices are reliable and durable, but half of the cost is the silicon wafer and efficiencies are limited to around 20%. A second generation of solar cells would use cheap semiconductor thin films deposited on low-cost substrates to produce devices of slightly lower efficiency. A number of thin-film device technologies account for around 5-6% of the current market. As second-generation technology reduces the cost of active material, the substrate will eventually be the cost limit and higher efficiency will be needed to maintain the cost-reduction trend. Third-generation devices will use new technologies to produce high-efficiency devices. Advances in nanotechnology, photonics, optical metamaterials, plasmonics and semiconducting polymer sciences offer the prospect of cost-competitive photovoltaics. It is reasonable to expect that cost reductions, a move to second-generation technologies and the implementation of new technologies and third-generation concepts can lead to fully cost-competitive solar energy in 10-15 years. (author)

Elaboration of technology organizational models of constructing high-rise buildings in plans of construction organization

Science.gov (United States)

Osipenkova, Irina; Simankina, Tatyana; Syrygina, Taisiia; Lukinov, Vitaliy

2018-03-01

This article represents features of the elaboration of technology organizational models of high-rise building construction in technology organizational documentation on the example of the plan of construction organization. Some examples of enhancing the effectiveness of high-rise building construction based on developments of several options of the organizational and technological plan are examined. Qualitative technology organizational documentation allows to increase the competitiveness of construction companies and provides prime cost of construction and assembly works reductions. Emphasis is placed on the necessity to comply with the principle of comprehensiveness of engineering, scientific and research works, development activities and scientific and technical support.

Design, performance and cost of energy from high concentration and flat-plate utility-scale PV systems

International Nuclear Information System (INIS)

Stolte, W.J.; Whisnant, R.A.; McGowin, C.R.

1993-01-01

This paper presents the results of a recent study to assess the near-term cost of power in central station applications. Three PV technologies were evaluated: Fresnel-lens high-concentration photovoltaic (HCPV), central receiver HCPV, and flat-plate PV using thin-film copper indium diselenide (CIS) cell technology. Baseline assumptions included PV cell designs and performances projected for the 1995 timeframe, 25 and 100 MW/year cell manufacturing rates, 50 MW power plant size, and mature technology cost and performance estimates. The plant design characteristics are highlighted. Potential sites were evaluated and selected for the PV power plants (Carrisa Plains, CA and Apalachicola, FL) and cell manufacturing plants (Dallas-Fort Worth, TX). Conceptual designs and cost estimates were developed for the plants and their components. Plant performance was modeled and the designs were optimized to minimize levelized energy costs. Overall, the flat plate design exhibited the lowest energy costs among the designs evaluated. Its levelized energy costs at the Carrisa Plains site were estimated to be 11.8 and 10.8 cents/kWh (1990 $) for 25 and 100 MW/year module production rates, respectively. This meets the 12 cents/kWh DOE near-term goal. The energy cost of the Fresnel lens plant (at Carrisa Plains and a 100 MW/year cell production rate) was estimated to be 12.4 cents/kWh and the corresponding central receiver energy cost was estimated to be 13.1 cents/kWh, both of which are very close to the DOE goal. Further design optimization efforts are still warranted and can be expected to reduce plant capital costs

Low cost technologies for the industrial waste water treatment; Tecnologia de tratamiento de aguas residuales industriales de bajo coste

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-31

Nowadays, the industrialism is gradually becoming more and more concerned on the way of reducing the disposal of pollutant waste. As well, he demands solutions for this problem but he usually guests a great disparity of technologies and costs. This article presents three low cost systems for purification of industrial waste water which are suitable for numerous applications.

Technology Estimating: A Process to Determine the Cost and Schedule of Space Technology Research and Development

Science.gov (United States)

Cole, Stuart K.; Reeves, John D.; Williams-Byrd, Julie A.; Greenberg, Marc; Comstock, Doug; Olds, John R.; Wallace, Jon; DePasquale, Dominic; Schaffer, Mark

2013-01-01

NASA is investing in new technologies that include 14 primary technology roadmap areas, and aeronautics. Understanding the cost for research and development of these technologies and the time it takes to increase the maturity of the technology is important to the support of the ongoing and future NASA missions. Overall, technology estimating may help provide guidance to technology investment strategies to help improve evaluation of technology affordability, and aid in decision support. The research provides a summary of the framework development of a Technology Estimating process where four technology roadmap areas were selected to be studied. The framework includes definition of terms, discussion for narrowing the focus from 14 NASA Technology Roadmap areas to four, and further refinement to include technologies, TRL range of 2 to 6. Included in this paper is a discussion to address the evaluation of 20 unique technology parameters that were initially identified, evaluated and then subsequently reduced for use in characterizing these technologies. A discussion of data acquisition effort and criteria established for data quality are provided. The findings obtained during the research included gaps identified, and a description of a spreadsheet-based estimating tool initiated as a part of the Technology Estimating process.

Helium High Pressure Tanks at EADS Space Transportation New Technology with Thermoplastic Liner

National Research Council Canada - National Science Library

Benedic, Fabien; Leard, Jean-Philippe; Lefloch, Christian

2005-01-01

Although EADS ST has been involved in high pressure tanks for 25 years. EADS ST is still developing new technologies and products to provide the best solution in response to the evolution of the market in terms of performances and costs...

Cost-Effective Additive Manufacturing in Space: HELIOS Technology Challenge Guide

Science.gov (United States)

DeVieneni, Alayna; Velez, Carlos Andres; Benjamin, David; Hollenbeck, Jay

2012-01-01

Welcome to the HELIOS Technology Challenge Guide. This document is intended to serve as a general road map for participants of the HELIOS Technology Challenge [HTC] Program and the associated inaugural challenge: HTC-01: Cost-Effective Additive Manufacturing in Space. Please note that this guide is not a rule book and is not meant to hinder the development of innovative ideas. Its primary goal is to highlight the objectives of the HTC-01 Challenge and to describe possible solution routes and pitfalls that such technology may encounter in space. Please also note that participants wishing to demonstrate any hardware developed under this program during any future HELIOS Technology Challenge showcase event(s) may be subject to event regulations to be published separately at a later date.

Impacts of nuclear fuel cycle costs on nuclear power generating costs

International Nuclear Information System (INIS)

Bertel, E.; Naudet, G.

1989-01-01

Fuel cycle costs are one of the main parameters to evaluate the competitiveness of various nuclear strategies. The historical analysis based on the French case shows the good performances yet achieved in mastering elementary costs in order to limit global fuel cycle cost escalation. Two contrasted theoretical scenarios of costs evolution in the middle and long term have been determined, based upon market analysis and technological improvements expected. They are used to calculate the global fuel cycle costs for various fuel management options and for three strategies of nuclear deployment. The results illustrate the stability of the expected fuel cycle costs over the long term, to be compared to the high incertainty prevailing for fossil fueled plants. The economic advantages of advanced technologies such as MOX fueled PWRs are underlined

Review of PV Inverter Technology Cost and Performance Projections

Energy Technology Data Exchange (ETDEWEB)

Navigant Consulting Inc.

2006-01-01

The National Renewable Energy Laboratory (NREL) has a major responsibility in the implementation of the U.S. Department of Energy's (DOE's) Solar Energy Technologies Program. Sandia National Laboratories (SNL) has a major role in supporting inverter development, characterization, standards, certifications, and verifications. The Solar Energy Technologies Program recently published a Multiyear Technical Plan, which establishes a goal of reducing the Levelized Energy Cost (LEC) for photovoltaic (PV) systems to $0.06/kWh by 2020. The Multiyear Technical Plan estimates that, in order to meet the PV system goal, PV inverter prices will need to decline to $0.25-0.30 Wp by 2020. DOE determined the need to conduct a rigorous review of the PV Program's technical and economic targets, including the target set for PV inverters. NREL requested that Navigant Consulting Inc.(NCI) conduct a review of historical and projected cost and performance improvements for PV inverters, including identification of critical barriers identified and the approaches government might use to address them.

How Subsurface Water Technologies (SWT) can Provide Robust, Effective, and Cost-Efficient Solutions for Freshwater Management in Coastal Zones

NARCIS (Netherlands)

Zuurbier, K.G.; Raat, K.J.; Paalman, M.; Oosterhof, A.T.; Stuyfzand, P.J.

2016-01-01

Freshwater resources in coastal zones are limited while demands are high, resulting in problems like seasonal water shortage, overexploitation of freshwater aquifers, and seawater intrusion. Three subsurface water technologies (SWT) that can provide robust, effective, and cost-efficient solutions to

A high-performance trench capacitor integrated in a passive integration technology

International Nuclear Information System (INIS)

Geiselbrechtinger, Angelika; Büyüktas, Kevni; Allers, Karl-Heinz; Hartung, Wolfgang

2009-01-01

The requirements for the electrical characteristics of passive on-chip devices become more and more important. The electrical performance of RF circuits is predominantly restricted by the passives. New technologies and new device concepts are necessary to meet the demands. In this work, a trench capacitor developed for RF applications is presented for the first time. This so-called SilCap (silicon capacitor) device features very high capacitance density, extreme low-voltage dependence, excellent temperature stability, good RF performance and a high breakthrough voltage. First, the device function and the technological concept are introduced. The concept is realized without implementing cost-intensive high-k materials. This trench capacitor is integrated in the front end of line of a passive integration technology. The achieved specific capacitance density is compared to a standard planar capacitor. Performance of the SilCap in terms of quality factor and breakthrough voltage is shown. Finally, reliability data of this trench capacitor are presented with special focus on extrinsic and dielectric lifetime

Innovative clean coal technology (ICCT): demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NOx) emission from high-sulfur, coal-fired boilers - economic evaluation of commercial-scale SCR applications for utility boilers

International Nuclear Information System (INIS)

Healy, E.C.; Maxwell, J.D.; Hinton, W.S.

1996-09-01

This report presents the results of an economic evaluation produced as part of the Innovative Clean Coal Technology project, which demonstrated selective catalytic reduction (SCR) technology for reduction of NO x emissions from utility boilers burning U.S. high-sulfur coal. The document includes a commercial-scale capital and O ampersand M cost evaluation of SCR technology applied to a new facility, coal-fired boiler utilizing high-sulfur U.S. coal. The base case presented herein determines the total capital requirement, fixed and variable operating costs, and levelized costs for a new 250-MW pulverized coal utility boiler operating with a 60-percent NO x removal. Sensitivity evaluations are included to demonstrate the variation in cost due to changes in process variables and assumptions. This report also presents the results of a study completed by SCS to determine the cost and technical feasibility of retrofitting SCR technology to selected coal-fired generating units within the Southern electric system

Low-cost high purity production

Science.gov (United States)

Kapur, V. K.

1978-01-01

Economical process produces high-purity silicon crystals suitable for use in solar cells. Reaction is strongly exothermic and can be initiated at relatively low temperature, making it potentially suitable for development into low-cost commercial process. Important advantages include exothermic character and comparatively low process temperatures. These could lead to significant savings in equipment and energy costs.

Development of ITM Oxygen Technology for Low-cost and Low-emission Gasification and Other Industrial Applications

Energy Technology Data Exchange (ETDEWEB)

Armstrong, Phillip

2014-11-01

Air Products is carrying out a scope of work under DOE Award No. DE-FE0012065 “Development of ITM Oxygen Technology for Low-cost and Low-emission Gasification and Other Industrial Applications.” The Statement of Project Objectives (SOPO) includes a Task 4f in which a Decision Point shall be reached, necessitating a review of Tasks 2-5 with an emphasis on Task 4f. This Topical Report constitutes the Decision Point Application pertaining to Task 4f. The SOPO under DOE Award No. DE-FE0012065 is aimed at furthering the development of the Ion Transport Membrane (ITM) Oxygen production process toward a demonstration scale facility known as the Oxygen Development Facility (ODF). It is anticipated that the completion of the current SOPO will advance the technology significantly along a pathway towards enabling the design and construction of the ODF. Development progress on several fronts is critical before an ODF project can commence; this Topical Report serves as an early update on the progress in critical development areas. Progress was made under all tasks, including Materials Development, Ceramic Processing Development, Engineering Development, and Performance Testing. Under Task 4f, Air Products carried out a cost and performance study in which several process design and cost parameters were varied and assessed with a process model and budgetary costing exercise. The results show that the major variables include ceramic module reliability, ITM operating temperature, module production yield, and heat addition strategy. High-temperature compact heat exchangers are shown to contribute significant cost benefits, while directly firing into the feed stream to an ITM are even a mild improvement on the high-temperature recuperation approach. Based on the findings to-date, Air Products recommends no changes to the content or emphasis in the current SOPO and recommends its completion prior to another formal assessment of these factors.

Low-Cost High-Concentration Photovoltaic Systems for Utility Power Generation

Energy Technology Data Exchange (ETDEWEB)

McConnell, R.; Garboushian, V.; Gordon, R.; Dutra, D.; Kinsey, G.; Geer, S.; Gomez, H.; Cameron, C.

2012-03-31

Under DOE's Technology Pathway Partnership (TPP) program, Amonix, Inc. developed a new generation of high-concentration photovoltaic systems using multijunction technology and established the manufacturing capacity needed to supply multi-megawatt power plants buing using the new Amonix 7700-series solar energy systems. For this effort, Amonix Collaborated with a variety of suppliers and partners to complete project tasks. Subcontractors included: Evonik/Cyro; Hitek; the National Renewable Energy Laboratory (NREL); Raytech; Spectrolab; UL; University of Nevada, Las Vegas; and TUV Rheinland PTL. The Amonix TPP tasks included: Task 1: Multijunction Cell Optimization for Field Operation, Task 2: Fresnel Lens R&D, Task 3: Cell Package Design & Production, Task 4: Standards Compliance and Reliability Testing, Task 5: Receiver Plate Production, Task 6: MegaModule Performance, Task 7: MegaModule Cost Reduction, Task 8: Factory Setup and MegaModule Production, Task 9: Tracker and Tracking Controller, Task 10: Installation and Balance of System (BOS), Task 11: Field Testing, and Task 12: Solar Advisor Modeling and Market Analysis. Amonix's TPP addressed nearly the complete PV value chain from epitaxial layer design and wafer processing through system design, manufacturing, deployment and O&M. Amonix has made progress toward achieving these reduced costs through the development of its 28%+ efficient MegaModule, reduced manufacturing and installation cost through design for manufacturing and assembly, automated manufacturing processes, and reduced O&M costs. Program highlights include: (1) Optimized multijunction cell and cell package design to improve performance by > 10%; (2) Updated lens design provided 7% increased performance and higher concentration; (3) 28.7% DC STC MegaModule efficiency achieved in Phase II exceeded Phase III performance goal; (4) New 16' focal length MegaModule achieved target materials and manufacturing cost reduction; (5) Designed and

The differential impact of low-carbon technologies on climate change mitigation cost under a range of socioeconomic and climate policy scenarios.

Energy Technology Data Exchange (ETDEWEB)

Barron, Robert W.; McJeon, Haewon C.

2015-05-01

This paper considers the effect of several key parameters of low carbon energy technologies on the cost of abatement. A methodology for determining the minimum level of performance required for a parameter to have a statistically significant impact on CO2 abatement cost is developed and used to evaluate the impact of eight key parameters of low carbon energy supply technologies on the cost of CO2 abatement. The capital cost of nuclear technology is found to have the greatest impact of the parameters studied. The cost of biomass and CCS technologies also have impacts, while their efficiencies have little, if any. Sensitivity analysis of the results with respect to population, GDP, and CO2 emission constraint show that the minimum performance level and impact of nuclear technologies is consistent across the socioeconomic scenarios studied, while the other technology parameters show different performance under higher population, lower GDP scenarios. Solar technology was found to have a small impact, and then only at very low costs. These results indicate that the cost of nuclear is the single most important driver of abatement cost, and that trading efficiency for cost may make biomass and CCS technologies more competitive.

Cost-effectiveness on a local level: whether and when to adopt a new technology.

Science.gov (United States)

Woertman, Willem H; Van De Wetering, Gijs; Adang, Eddy M M

2014-04-01

Cost-effectiveness analysis has become a widely accepted tool for decision making in health care. The standard textbook cost-effectiveness analysis focuses on whether to make the switch from an old or common practice technology to an innovative technology, and in doing so, it takes a global perspective. In this article, we are interested in a local perspective, and we look at the questions of whether and when the switch from old to new should be made. A new approach to cost-effectiveness from a local (e.g., a hospital) perspective, by means of a mathematical model for cost-effectiveness that explicitly incorporates time, is proposed. A decision rule is derived for establishing whether a new technology should be adopted, as well as a general rule for establishing when it pays to postpone adoption by 1 more period, and a set of decision rules that can be used to determine the optimal timing of adoption. Finally, a simple example is presented to illustrate our model and how it leads to optimal decision making in a number of cases.

Coverage Range and Cost Comparison of Remote Antenna Unit Designs for Inbuilding Radio over Fiber Technology

Directory of Open Access Journals (Sweden)

Razali Ngah

2013-09-01

Full Text Available Future communication needs to be ubiquitous, broadband, convergent, and seamless. Radio over fiber (RoF technology is one of the most important enabler in access network for the technologies. Adoption of RoF faces bottleneck in optoelectronics, that they are still expensive, high power consumption, and limited in bandwidth. To solve the problem, transceiver in remote antenna unit (RAU is developed, i.e. electroabsorption transceiver (EAT and asymmetric FabryPerot modulator (AFPM. This paper compares their coverage range and cost in providing WCDMA and WLAN services. Needed gain of RF amplifier for supporting picocell is also discussed.

Assessing the effect of standardized cost systems on financial performance. A difference-in-differences approach for hospitals according to their technological level.

Science.gov (United States)

García-Cornejo, Beatriz; Pérez-Méndez, José A

2018-04-01

Promoting the improvement of standardized cost systems (CS) is one of the measures available to health policy makers for the purpose of improving efficiency in hospitals over the long-term. Nevertheless, very few studies evaluate the relationship between alternative CS and the costs really incurred. We use data from 242 hospitals of the Spanish National Health Service (NHS) between 2010 and 2013 in order to explore the determinants of the cost per adjusted patient day, using a difference-in-differences approach where the treatment is the implementation of an advanced CS. We also investigate if the association between advanced CS and unit cost is different depending upon the technological level of the hospital. Results show that hospitals with more advanced CS contained their costs better. However, the latter effect of advanced CS is lower in hospitals with a greater endowment of high technology. Results suggest that health authorities should support the development of CS, particularly in high-tech hospitals, which are usually larger and more complex hospitals that tend to accumulate a greater portion of NHS hospital sector expenditure. Copyright © 2018 Elsevier B.V. All rights reserved.

High-power free-electron lasers-technology and future applications

Science.gov (United States)

Socol, Yehoshua

2013-03-01

Free-electron laser (FEL) is an all-electric, high-power, high beam-quality source of coherent radiation, tunable - unlike other laser sources - at any wavelength within wide spectral region from hard X-rays to far-IR and beyond. After the initial push in the framework of the “Star Wars” program, the FEL technology benefited from decades of R&D and scientific applications. Currently, there are clear signs that the FEL technology reached maturity, enabling real-world applications. E.g., successful and unexpectedly smooth commissioning of the world-first X-ray FEL in 2010 increased in one blow by more than an order of magnitude (40×) wavelength region available by FEL technology and thus demonstrated that the theoretical predictions just keep true in real machines. Experience of ordering turn-key electron beamlines from commercial companies is a further demonstration of the FEL technology maturity. Moreover, successful commissioning of the world-first multi-turn energy-recovery linac demonstrated feasibility of reducing FEL size, cost and power consumption by probably an order of magnitude in respect to previous configurations, opening way to applications, previously considered as non-feasible. This review takes engineer-oriented approach to discuss the FEL technology issues, keeping in mind applications in the fields of military and aerospace, next generation semiconductor lithography, photo-chemistry and isotope separation.

Application of high speed machining technology in aviation

Science.gov (United States)

Bałon, Paweł; Szostak, Janusz; Kiełbasa, Bartłomiej; Rejman, Edward; Smusz, Robert

2018-05-01

Aircraft structures are exposed to many loads during their working lifespan. Every particular action made during a flight is composed of a series of air movements which generate various aircraft loads. The most rigorous requirement which modern aircraft structures must fulfill is to maintain their high durability and reliability. This requirement involves taking many restrictions into account during the aircraft design process. The most important factor is the structure's overall mass, which has a crucial impact on both utility properties and cost-effectiveness. This makes aircraft one of the most complex results of modern technology. Additionally, there is currently an increasing utilization of high strength aluminum alloys, which requires the implementation of new manufacturing processes. High Speed Machining technology (HSM) is currently one of the most important machining technologies used in the aviation industry, especially in the machining of aluminium alloys. The primary difference between HSM and other milling techniques is the ability to select cutting parameters - depth of the cut layer, feed rate, and cutting speed in order to simultaneously ensure high quality, precision of the machined surface, and high machining efficiency, all of which shorten the manufacturing process of the integral components. In this paper, the authors explain the implementation of the HSM method in integral aircraft constructions. It presents the method of the airframe manufacturing method, and the final results. The HSM method is compared to the previous method where all subcomponents were manufactured by bending and forming processes, and then, they were joined by riveting.

Effects of economies of scale and experience on the costs of energy-efficient technologies. Case study of electric motors in Germany

Energy Technology Data Exchange (ETDEWEB)

Jardot, D.; Eichhammer, W.; Fleiter, T. [Fraunhofer Institute for Systems and Innovation Research (ISI), Breslauer Str. 48, 76139 Karlsruhe (Germany)

2010-11-15

Increasing energy efficiency is discussed as an effective way to protect the climate, even though this is frequently associated with additional (investment) costs when compared to standard technologies. However, the investment costs of emerging energy-efficient technologies can be reduced by economies of scale and experience curve effects. This also brings about higher market penetration by lowering market barriers. Experience curves have already been analyzed in detail for renewable energy technologies, but are not as well documented for energy-efficient technologies despite their significance for energy and climate policy decisions. This work provides empirical evidence for effects of economies of scale and experience on the costs of energy-efficient electric motors. We apply a new methodology to the estimation of learning effects that is particularly promising for energy-efficient technologies where the very low data availability did not allow calculations of learning rates so far. Energy-efficient electric motors are a highly relevant energy technology that is responsible for about 55% of German electricity consumption. The analysis consists of three main steps. First, the calculation of composite price indices based on gross value added statistics for Germany which show the changes in cost components of electric motors over the period 1995 to 2006; second, an estimation of the corresponding learning rate which is, in a third step, compared with learning rates observed for other energy-efficient technologies in a literature review. Due to restrictions of data availability, it was not possible to calculate a learning rate for the differential costs of energy-efficient motors compared to standard motors. Still, we estimated a learning rate of 9% for 'Eff2' motors in a period when they penetrated the market and replaced the less efficient 'Eff3' motors. Furthermore, we showed the contribution of different effects to these cost reductions, like

The role of technology in reducing health care costs. Phase II and phase III.

Energy Technology Data Exchange (ETDEWEB)

Cilke, John F.; Parks, Raymond C.; Funkhouser, Donald Ray; Tebo, Michael A.; Murphy, Martin D.; Hightower, Marion Michael; Gallagher, Linda K.; Craft, Richard Layne, II; Garcia, Rudy John

2004-04-01

In Phase I of this project, reported in SAND97-1922, Sandia National Laboratories applied a systems approach to identifying innovative biomedical technologies with the potential to reduce U.S. health care delivery costs while maintaining care quality. The effort provided roadmaps for the development and integration of technology to meet perceived care delivery requirements and an economic analysis model for development of care pathway costs for two conditions: coronary artery disease (CAD) and benign prostatic hypertrophy (BPH). Phases II and III of this project, which are presented in this report, were directed at detailing the parameters of telemedicine that influence care delivery costs and quality. These results were used to identify and field test the communication, interoperability, and security capabilities needed for cost-effective, secure, and reliable health care via telemedicine.

Financing end-use solar technologies in a restructured electricity industry: Comparing the cost of public policies

International Nuclear Information System (INIS)

Jones, E.; Eto, J.

1997-09-01

Renewable energy technologies are capital intensive. Successful public policies for promoting renewable energy must address the significant resources needed to finance them. Public policies to support financing for renewable energy technologies must pay special attention to interactions with federal, state, and local taxes. These interactions are important because they can dramatically increase or decrease the effectiveness of a policy, and they determine the total cost of a policy to society as a whole. This report describes a comparative analysis of the cost of public policies to support financing for two end-use solar technologies: residential solar domestic hot water heating (SDHW) and residential rooftop photovoltaic (PV) systems. The analysis focuses on the cost of the technologies under five different ownership and financing scenarios. Four scenarios involve leasing the technologies to homeowners in return for a payment that is determined by the financing requirements of each form of ownership. For each scenario, the authors examine nine public policies that might be used to lower the cost of these technologies: investment tax credits (federal and state), production tax credits (federal and state), production incentives, low-interest loans, grants (taxable and two types of nontaxable), direct customer payments, property and sales tax reductions, and accelerated depreciation

The impact of technology on health care cost and policy development.

Science.gov (United States)

Wallner, Paul E; Konski, Andre

2008-07-01

As health care spending in the United States continues to increase at a pace significantly faster than that of other sectors of the economy, there seems to be greater interest and willingness to consider the root causes of the rise and to explore options for reform. Some of the reasons for cost escalation are associated with a growing and aging population that all too often makes inappropriate personal choices, but others are clearly attributable to growth in the cost of drugs, hospital and nursing home care, provider reimbursement, and durable medical equipment. Some health care economists have suggested that the rapid introduction of new technologies has also played a major role. Vendors understandably desire early market penetration of any new device or technology, but often this may be accomplished before significant evidence of benefit is available. Our current system of device approval unlinked to coverage and payment has produced further disruption in the system. The nature of the problem and consideration of various factors in the introduction, implementation, and evaluation of new technologies will be considered.

Superconducting Magnet Technology for Future High Energy Proton Colliders

Science.gov (United States)

Gourlay, Stephen

2017-01-01

Interest in high field dipoles has been given a boost by new proposals to build a high-energy proton-proton collider to follow the LHC and programs around the world are taking on the task to answer the need. Studies aiming toward future high-energy proton-proton colliders at the 100 TeV scale are now being organized. The LHC and current cost models are based on technology close to four decades old and point to a broad optimum of operation using dipoles with fields between 5 and 12T when site constraints, either geographical or political, are not a factor. Site geography constraints that limit the ring circumference can drive the required dipole field up to 20T, which is more than a factor of two beyond state-of-the-art. After a brief review of current progress, the talk will describe the challenges facing future development and present a roadmap for moving high field accelerator magnet technology forward. This work was supported by the Director, Office of Science, High Energy Physics, US Department of Energy, under contract No. DE-AC02-05CH11231.

The role of technology in reducing health care costs. Final project report

Energy Technology Data Exchange (ETDEWEB)

Sill, A.E.; Warren, S.; Dillinger, J.D.; Cloer, B.K.

1997-08-01

Sandia National Laboratories applied a systems approach to identifying innovative biomedical technologies with the potential to reduce U.S. health care delivery costs while maintaining care quality. This study was conducted by implementing both top-down and bottom-up strategies. The top-down approach used prosperity gaming methodology to identify future health care delivery needs. This effort provided roadmaps for the development and integration of technology to meet perceived care delivery requirements. The bottom-up approach identified and ranked interventional therapies employed in existing care delivery systems for a host of health-related conditions. Economic analysis formed the basis for development of care pathway interaction models for two of the most pervasive, chronic disease/disability conditions: coronary artery disease (CAD) and benign prostatic hypertrophy (BPH). Societal cost-benefit relationships based on these analyses were used to evaluate the effect of emerging technology in these treatment areas. 17 figs., 48 tabs.

Transaction costs, externalities and information technology in health care.

Science.gov (United States)

Ferguson, B; Keen, J

1996-01-01

This paper discusses some of the economic issues which underpin the rationale for investment in information and communications technologies (ICTs). Information imperfections lead to significant transaction costs (search, negotiating and monitoring) which in turn confer a negative externality on parties involved in exchange. This divergence in private and social costs leads to a degree of resource misallocation (efficiency loss) which, uncorrected, results in a sub-optimal outcome. Traditional solutions to this problem are to rely upon direct government action to reduce the costs of transacting between market agents, or to employ tax/subsidy measures and other legislative action to achieve the desired market outcome. Three key policy questions are raised in the context of the NHS purchaser/provider relationship. Firstly, what is the optimum level of transaction costs; secondly, can ICTs assist in lowering the level of transaction costs to the optimum level; thirdly, who should bear the investment cost in reducing the level of transaction costs? The issue of property rights in different information systems is discussed and raises interesting policy questions about how much investment should be undertaken centrally rather than devolved to a more local level. In some ways this economic framework offers a post hoc justification of why different ICT systems have been introduced at various levels of the NHS. Essentially this reduces to the problem of externalities: providing good information confers a positive externality: not providing relevant, timely and accurate information confers a negative externality, by increasing further the level of transaction costs. The crucial role which ICT systems can play lies in attempting to reduce the level of transaction costs and driving the market towards what Dahlman has described as the transaction-cost-constrained equilibrium.

Transportation Energy Futures Series: Non-Cost Barriers to Consumer Adoption of New Light-Duty Vehicle Technologies

Energy Technology Data Exchange (ETDEWEB)

Stephens, T.

2013-03-01

Consumer preferences are key to the adoption of new vehicle technologies. Barriers to consumer adoption include price and other obstacles, such as limited driving range and charging infrastructure; unfamiliarity with the technology and uncertainty about direct benefits; limited makes and models with the technology; reputation or perception of the technology; standardization issues; and regulations. For each of these non-cost barriers, this report estimates an effective cost and summarizes underlying influences on consumer preferences, approximate magnitude and relative severity, and assesses potential actions, based on a comprehensive literature review. While the report concludes that non-cost barriers are significant, effective cost and potential market share are very uncertain. Policies and programs including opportunities for drivers to test drive advanced vehicles, general public outreach and information programs, incentives for providing charging and fueling infrastructure, and development of technology standards were examined for their ability to address barriers, but little quantitative data exists on the effectiveness of these measures. This is one in a series of reports produced as a result of the Transportation Energy Futures project, a Department of Energy-sponsored multi-agency effort to pinpoint underexplored strategies for reducing GHGs and petroleum dependence related to transportation.

Technological Aspects: High Voltage

CERN Document Server

Faircloth, D.C.

2013-12-16

This paper covers the theory and technological aspects of high-voltage design for ion sources. Electric field strengths are critical to understanding high-voltage breakdown. The equations governing electric fields and the techniques to solve them are discussed. The fundamental physics of high-voltage breakdown and electrical discharges are outlined. Different types of electrical discharges are catalogued and their behaviour in environments ranging from air to vacuum are detailed. The importance of surfaces is discussed. The principles of designing electrodes and insulators are introduced. The use of high-voltage platforms and their relation to system design are discussed. The use of commercially available high-voltage technology such as connectors, feedthroughs and cables are considered. Different power supply technologies and their procurement are briefly outlined. High-voltage safety, electric shocks and system design rules are covered.

Liberalised electricity markets, new bioenergy technologies, and GHG emission reductions: interactions and CO2 mitigation costs

International Nuclear Information System (INIS)

Gustavsson, L.; Madlener, R.

1999-01-01

We contrast recent developments in power and heat production with bioenergy, and natural-gas-fired condensing plants with and without decarbonisation, in the light of electricity market liberalisation. Our main focus is on CO 2 mitigation costs and carbon tax sensitivity of production costs. We find that CO 2 mitigation costs are lower for biomass systems using IGCC technology than for natural gas system using decarbonisation. However, based on current fuel prices natural-gas fired co-generation plants have the lowest production costs. Hence energy policy measures will be needed to promote biomass technologies and decarbonisation options on a liberalised market. (author)

[Bayesian approach for the cost-effectiveness evaluation of healthcare technologies].

Science.gov (United States)

Berchialla, Paola; Gregori, Dario; Brunello, Franco; Veltri, Andrea; Petrinco, Michele; Pagano, Eva

2009-01-01

The development of Bayesian statistical methods for the assessment of the cost-effectiveness of health care technologies is reviewed. Although many studies adopt a frequentist approach, several authors have advocated the use of Bayesian methods in health economics. Emphasis has been placed on the advantages of the Bayesian approach, which include: (i) the ability to make more intuitive and meaningful inferences; (ii) the ability to tackle complex problems, such as allowing for the inclusion of patients who generate no cost, thanks to the availability of powerful computational algorithms; (iii) the importance of a full use of quantitative and structural prior information to produce realistic inferences. Much literature comparing the cost-effectiveness of two treatments is based on the incremental cost-effectiveness ratio. However, new methods are arising with the purpose of decision making. These methods are based on a net benefits approach. In the present context, the cost-effectiveness acceptability curves have been pointed out to be intrinsically Bayesian in their formulation. They plot the probability of a positive net benefit against the threshold cost of a unit increase in efficacy.A case study is presented in order to illustrate the Bayesian statistics in the cost-effectiveness analysis. Emphasis is placed on the cost-effectiveness acceptability curves. Advantages and disadvantages of the method described in this paper have been compared to frequentist methods and discussed.

Nuclear reactors' construction costs: The role of lead-time, standardization and technological progress

International Nuclear Information System (INIS)

Berthelemy, Michel; Escobar Rangel, Lina

2013-01-01

This paper provides the first comparative analysis of nuclear reactor construction costs in France and the United States. Studying the cost of nuclear power has often been a challenge, owing to the lack of reliable data sources and heterogeneity between countries, as well as the long time horizon which requires controlling for input prices and structural changes. We build a simultaneous system of equations for overnight costs and construction time (lead-time) to control for endogeneity, using expected demand variation as an instrument. We argue that benefits from nuclear reactor program standardization can arise through short term coordination gains, when the diversity of nuclear reactors' technologies under construction is low, or through long term benefits from learning spillovers from past reactor construction experience, if those spillovers are limited to similar reactors. We find that overnight construction costs benefit directly from learning spillovers but that these spillovers are only significant for nuclear models built by the same Architect-Engineer (A- E). In addition, we show that the standardization of nuclear reactors under construction has an indirect and positive effect on construction costs through a reduction in lead-time, the latter being one of the main drivers of construction costs. Conversely, we also explore the possibility of learning by searching and find that, contrary to other energy technologies, innovation leads to construction costs increases. (authors)

Low Cost Advanced Thermoelectric (TE) Technology for Automotive Waste Heat Recovery

Science.gov (United States)

Meisner, G. P.

2014-03-01

Low cost, fully integrated TE generators (TEGs) to recover waste heat from vehicle exhaust will reduce transportation sector energy consumption and emissions. TEGs will be the first application of high-temperature TE materials for high-volume use and establish new industrial sectors with scaled up production capability of TEG materials and components. We will create a potential supply chain for practical automotive TEGs and identify manufacturing and assembly processes for large scale production of TEG materials and components. Our work focusses on several innovative R&D paths: (1) enhanced TE material performance by doping and compositional tuning, (2) optimized TE material fabrication and processing to reduce thermal conductivity and improve fracture strength, (3) high volume production for successful skutterudite commercialization, (4) new material, nanostructure, and nanoscale approaches to reduce thermal interface and electrical contact resistances, (5) innovative heat exchangers for high efficiency heat flows and optimum temperature profiles despite highly variable exhaust gas operating conditions, (6) new modeling and simulation tools, and (7) inexpensive materials for thermal insulation and coatings for TE encapsulation. Recent results will be presented. Supported by the U.S. DOE Vehicle Technology Program.

Cost, Time, and Risk Assessment of Different Wave Energy Converter Technology Development Trajectories: Preprint

Energy Technology Data Exchange (ETDEWEB)

Weber, Jochem W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Laird, Daniel [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Costello, Ronan [Wave Venture; Roberts, Jesse [Sandia National Laboratories; Bull, Diana [Sandia National Laboratories; Babarit, Aurelien [Ecole Centrale de Nantes; Nielsen, Kim [Ramboll; Ferreira, Claudio Bittencourt [DNV-GL; Kennedy, Ben [Wave Venture

2017-09-14

This paper presents a comparative assessment of three fundamentally different wave energy converter technology development trajectories. The three technology development trajectories are expressed and visualised as a function of technology readiness levels and technology performance levels. The assessment shows that development trajectories that initially prioritize technology readiness over technology performance are likely to require twice the development time, consume a threefold of the development cost, and are prone to a risk of technical or commercial failure of one order of magnitude higher than those development trajectories that initially prioritize technology performance over technology readiness.

Cost development of future technologies for power generation-A study based on experience curves and complementary bottom-up assessments

International Nuclear Information System (INIS)

Neij, Lena

2008-01-01

Technology foresight studies have become an important tool in identifying realistic ways of reducing the impact of modern energy systems on the climate and the environment. Studies on the future cost development of advanced energy technologies are of special interest. One approach widely adopted for the analysis of future cost is the experience curve approach. The question is, however, how robust this approach is, and which experience curves should be used in energy foresight analysis. This paper presents an analytical framework for the analysis of future cost development of new energy technologies for electricity generation; the analytical framework is based on an assessment of available experience curves, complemented with bottom-up analysis of sources of cost reductions and, for some technologies, judgmental expert assessments of long-term development paths. The results of these three methods agree in most cases, i.e. the cost (price) reductions described by the experience curves match the incremental cost reduction described in the bottom-up analysis and the judgmental expert assessments. For some technologies, the bottom-up analysis confirms large uncertainties in future cost development not captured by the experience curves. Experience curves with a learning rate ranging from 0% to 20% are suggested for the analysis of future cost development

High performance superconducting radio frequency ingot niobium technology for continuous wave applications

International Nuclear Information System (INIS)

Dhakal, Pashupati; Ciovati, Gianluigi; Myneni, Ganapati R.

2015-01-01

Future continuous wave (CW) accelerators require the superconducting radio frequency cavities with high quality factor and medium accelerating gradients (≤20 MV/m). Ingot niobium cavities with medium purity fulfill the specifications of both accelerating gradient and high quality factor with simple processing techniques and potential reduction in cost. This contribution reviews the current superconducting radiofrequency research and development and outlines the potential benefits of using ingot niobium technology for CW applications

Technological Aspects: High Voltage

International Nuclear Information System (INIS)

Faircloth, D C

2013-01-01

This paper covers the theory and technological aspects of high-voltage design for ion sources. Electric field strengths are critical to understanding high-voltage breakdown. The equations governing electric fields and the techniques to solve them are discussed. The fundamental physics of high-voltage breakdown and electrical discharges are outlined. Different types of electrical discharges are catalogued and their behaviour in environments ranging from air to vacuum are detailed. The importance of surfaces is discussed. The principles of designing electrodes and insulators are introduced. The use of high-voltage platforms and their relation to system design are discussed. The use of commercially available high-voltage technology such as connectors, feedthroughs and cables are considered. Different power supply technologies and their procurement are briefly outlined. High-voltage safety, electric shocks and system design rules are covered. (author)

Assessing community exposure to hazardous air pollutants by combining optical remote sensing and "low-cost" sensor technologies

Science.gov (United States)

Pikelnaya, O.; Polidori, A.; Wimmer, R.; Mellqvist, J.; Samuelsson, J.; Marianne, E.; Andersson, P.; Brohede, S.; Izos, O.

2017-12-01

Industrial facilities such as refineries and oil processing facilities can be sources of chemicals adversely affecting human health, for example aromatic hydrocarbons and formaldehyde. In an urban setting, such as the South Coast Air Basin (SCAB), exposure to harmful air pollutants (HAP's) for residents of communities neighboring such facilities is of serious concern. Traditionally, exposure assessments are performed by modeling a community exposure using emission inventories and data collected at fixed air monitoring sites. However, recent field measurements found that emission inventories may underestimate HAP emissions from refineries; and HAP measurements data from fixed sites is lacking spatial resolution; as a result, the impact of HAP emissions on communities is highly uncertain. The next generation air monitoring technologies can help address these challenges. For example, dense "low-cost" sensors allow continuous monitoring of concentrations of pollutants within communities with high temporal- and spatial- resolution, and optical remote sensing (ORS) technologies offer measurements of emission fluxes and real-time ground-concentration mapping of HAPs. South Coast Air Quality Management District (SCAQMD) is currently conducting a multi-year study using ORS methods and "low-cost" Volatile Organic Compounds (VOCs) sensors to monitor HAP emissions from selected industrial facilities in the SCAB and their ambient concentrations in neighboring communities. For this purpose, quarterly mobile ORS surveys are conducted to quantify facility-wide emissions for VOCs, aromatic hydrocarbons and HCHO, and to collect ground-concentration profiles of these pollutants inside neighboring communities. Additionally, "low-cost" sensor nodes for deployment in neighborhood(s) downwind of the facilities have been developed in order to obtain long-term, granular data on neighborhood VOC concentrations, During this presentation we will discuss initial results of quarterly ORS

Reducing the cost of back-contact module technology

Energy Technology Data Exchange (ETDEWEB)

Bennett, I.J.; Eerenstein, W.; Rosca, V. [ECN Solar Energy, P.O. Box 1, 1755 ZG Petten (Netherlands)

2013-07-01

Back-contact modules made using a conductive back-sheet foil have a number of advantages over standard H-pattern modules including a higher power output, compatibility with very thin cells and high throughput, high yield manufacturing. For a conductive back-sheet based module the most cost critical components are the conductive back-sheet and the conductive adhesives used to make the contact between the cells and the conductive back-sheet. In this paper a number of methods for reducing the module materials cost will be presented. Climate chamber testing of low cost foils without isolation coating and without silver contacts demonstrated that this type of foil is reliable in damp-heat, reaching 2000 hours at 85%RH and 85{sup o}C with a loss in fill-factor of less than 2%.

Cost estimate guidelines for advanced nuclear power technologies

International Nuclear Information System (INIS)

Delene, J.G.; Hudson, C.R. II.

1993-05-01

Several advanced power plant concepts are currently under development. These include the Modular High Temperature Gas Cooled Reactors, the Advanced Liquid Metal Reactor and the Advanced Light Water Reactors. One measure of the attractiveness of a new concept is its cost. Invariably, the cost of a new type of power plant will be compared with other alternative forms of electrical generation. This report provides a common starting point, whereby the cost estimates for the various power plants to be considered are developed with common assumptions and ground rules. Comparisons can then be made on a consistent basis. This is the second update of these cost estimate guidelines. Changes have been made to make the guidelines more current (January 1, 1992) and in response to suggestions made as a result of the use of the previous report. The principal changes are that the reference site has been changed from a generic Northeast (Middletown) site to a more central site (EPRI's East/West Central site) and that reference bulk commodity prices and labor productivity rates have been added. This report is designed to provide a framework for the preparation and reporting of costs. The cost estimates will consist of the overnight construction cost, the total plant capital cost, the operation and maintenance costs, the fuel costs, decommissioning costs and the power production or busbar generation cost

Technology interactions among low-carbon energy technologies: What can we learn from a large number of scenarios?

International Nuclear Information System (INIS)

McJeon, Haewon C.; Clarke, Leon; Kyle, Page; Wise, Marshall; Hackbarth, Andrew; Bryant, Benjamin P.; Lempert, Robert J.

2011-01-01

Advanced low-carbon energy technologies can substantially reduce the cost of stabilizing atmospheric carbon dioxide concentrations. Understanding the interactions between these technologies and their impact on the costs of stabilization can help inform energy policy decisions. Many previous studies have addressed this challenge by exploring a small number of representative scenarios that represent particular combinations of future technology developments. This paper uses a combinatorial approach in which scenarios are created for all combinations of the technology development assumptions that underlie a smaller, representative set of scenarios. We estimate stabilization costs for 768 runs of the Global Change Assessment Model (GCAM), based on 384 different combinations of assumptions about the future performance of technologies and two stabilization goals. Graphical depiction of the distribution of stabilization costs provides first-order insights about the full data set and individual technologies. We apply a formal scenario discovery method to obtain more nuanced insights about the combinations of technology assumptions most strongly associated with high-cost outcomes. Many of the fundamental insights from traditional representative scenario analysis still hold under this comprehensive combinatorial analysis. For example, the importance of carbon capture and storage (CCS) and the substitution effect among supply technologies are consistently demonstrated. The results also provide more clarity regarding insights not easily demonstrated through representative scenario analysis. For example, they show more clearly how certain supply technologies can provide a hedge against high stabilization costs, and that aggregate end-use efficiency improvements deliver relatively consistent stabilization cost reductions. Furthermore, the results indicate that a lack of CCS options combined with lower technological advances in the buildings sector or the transportation sector is

Wood chip production technology and costs for fuel in Namibia

Energy Technology Data Exchange (ETDEWEB)

Leinonen, A.

2007-12-15

This work has been done in the project where the main target is to evaluate the technology and economy to use bush biomass for power production in Namibia. The project has been financed by the Ministry for Foreign Affairs of Finland and the Ministry of Agriculture, Water and Forestry of the Republic of Namibia. The target of this study is to calculate the production costs of bush chips at the power plant using the current production technology and to look possibilities to develop production technology in order to mechanize production technology and to decrease the production costs. The wood production costs are used in feasibility studies, in which the technology and economy of utilization of wood chips for power generation in 5, 10 and 20 MW electric power plants and for power generation in Van Eck coal fired power plant in Windhoek are evaluated. Field tests were made at Cheetah Conservation Farm (CCF) in Otjiwarongo region. CCF is producing wood chips for briquette factory in Otjiwarongo. In the field tests it has been gathered information about this CCF semi-mechanized wood chip production technology. Also new machines for bush biomass chip production have been tested. A new mechanized production chain has been designed on the basis of this information. The production costs for the CCF semi-mechanized and the new production chain have been calculated. The target in the moisture content to produce wood chips for energy is 20 w-%. In the semi-mechanized wood chip production chain the work is done partly manually, and the supply chain is organized into crews of 4.8 men. The production chain consists of manual felling and compiling, drying, chipping with mobile chipper and manual feeding and road transport by a tractor with two trailers. The CCF production chain works well. The chipping and road transport productivity in the semimechanized production chain is low. New production machines, such as chainsaw, brush cutter, lawn mover type cutter, rotator saw in skid

Batteries: Lower cost than gasoline?

International Nuclear Information System (INIS)

Werber, Mathew; Fischer, Michael; Schwartz, Peter V.

2009-01-01

We compare the lifecycle costs of an electric car to a similar gasoline-powered vehicle under different scenarios of required driving range and cost of gasoline. An electric car is cost competitive for a significant portion of the scenarios: for cars of lower range and for higher gasoline prices. Electric cars with ∼150 km range are a technologically viable, cost competitive, high performance, high efficiency alternative that can presently suit the vast majority of consumers' needs.

Low-Cost In-Fill Installation for High-Energy-Saving, Dynamic Windows

Science.gov (United States)

2017-07-01

increase 2% annually. This is consistent with national recognized energy prediction models. Electrical Labor costs: Electrical labor cost for wiring...Technology Description: ................................................................................................ 3 2.1.2 Energy Consumption ...22 Figure 15. Energy Consumption for the Calibration Period of 9/2/2015 - 9/16/2015

Industry-Cost-Curve Approach for Modeling the Environmental Impact of Introducing New Technologies in Life Cycle Assessment.

Science.gov (United States)

Kätelhön, Arne; von der Assen, Niklas; Suh, Sangwon; Jung, Johannes; Bardow, André

2015-07-07

The environmental costs and benefits of introducing a new technology depend not only on the technology itself, but also on the responses of the market where substitution or displacement of competing technologies may occur. An internationally accepted method taking both technological and market-mediated effects into account, however, is still lacking in life cycle assessment (LCA). For the introduction of a new technology, we here present a new approach for modeling the environmental impacts within the framework of LCA. Our approach is motivated by consequential life cycle assessment (CLCA) and aims to contribute to the discussion on how to operationalize consequential thinking in LCA practice. In our approach, we focus on new technologies producing homogeneous products such as chemicals or raw materials. We employ the industry cost-curve (ICC) for modeling market-mediated effects. Thereby, we can determine substitution effects at a level of granularity sufficient to distinguish between competing technologies. In our approach, a new technology alters the ICC potentially replacing the highest-cost producer(s). The technologies that remain competitive after the new technology's introduction determine the new environmental impact profile of the product. We apply our approach in a case study on a new technology for chlor-alkali electrolysis to be introduced in Germany.

Transportation Energy Futures Series. Non-Cost Barriers to Consumer Adoption of New Light-Duty Vehicle Technologies

Energy Technology Data Exchange (ETDEWEB)

Stephens, Thomas [Argonne National Lab. (ANL), Argonne, IL (United States)

2013-03-01

Consumer preferences are key to the adoption of new vehicle technologies. Barriers to consumer adoption include price and other obstacles, such as limited driving range and charging infrastructure; unfamiliarity with the technology and uncertainty about direct benefits; limited makes and models with the technology; reputation or perception of the technology; standardization issues; and regulations. For each of these non-cost barriers, this report estimates an effective cost and summarizes underlying influences on consumer preferences, approximate magnitude and relative severity, and assesses potential actions, based on a comprehensive literature review. While the report concludes that non-cost barriers are significant, effective cost and potential market share are very uncertain. Policies and programs including opportunities for drivers to test drive advanced vehicles, general public outreach and information programs, incentives for providing charging and fueling infrastructure, and development of technology standards were examined for their ability to address barriers, but little quantitative data exists on the effectiveness of these measures. This is one in a series of reports produced as a result of the Transportation Energy Futures project, a Department of Energy-sponsored multi-agency effort to pinpoint underexplored strategies for reducing GHGs and petroleum dependence related to transportation. View all reports on the TEF Web page, http://www.eere.energy.gov/analysis/transportationenergyfutures/index.html.

Overview of the Performance and Cost Effectiveness of Small Arsenic Removal Technologies

Science.gov (United States)

Presentation provides information on the performance and cost of primarily four arsenic removal technologies; adsorptive media, iron removal, coagulation/filtration and the combination system of iron removal followed by adsorptive media.

Cost effective multi-storey passive residential houses. Costs, technology, solutions, experiences of users; Kostenguenstige mehrgeschossige Passivwohnhaeuser. Kosten, Technik, Loesungen, Nutzererfahrungen

Energy Technology Data Exchange (ETDEWEB)

Schoeberl, Helmut

2013-08-01

Energy-efficient buildings in the range of single-family houses are no longer a rarity. The passive house technology and the costs are the significant barriers in the field of multi-storey housings. For the first time, the author of the book under consideration summarizes the planning tools, building envelope, building services, construction costs and the introduction of users by means of several passive house projects. The demands, components and challenges of the passive house are presented. Even experienced planners and decision-makers with get many detailed solutions and an accurate arrangement of additional costs.

Cost effectiveness analysis of the SEAMIST trademark membrane system technology

International Nuclear Information System (INIS)

Henriksen, A.D.; Booth, S.R.

1993-01-01

This report describes the cost and performance characteristics of SEAMIST trademark, an innovative technology that facilitates measurements of contaminants in both vertical and horizontal vadose zone boreholes. This new technology consists of an airtight membrane linear that is pneumatically emplaced inside the borehole structure. Sampling ports with attached tubing, absorbent collectors, or various in situ measuring devices can be fabricated into the linear and used for monitoring volatile organic compounds (VOCs), semivolatile organic compounds (SVOCs), pesticides, herbicides, polynuclear aromatic hydrocarbons, polychlorinated biphenyls, or radioactive substances. In addition, small instruments can be guided through the lined borehole and measurements taken inside at specified intervals

Benchmarking the expected stack manufacturing cost of next generation, intermediate-temperature protonic ceramic fuel cells with solid oxide fuel cell technology

Science.gov (United States)

Dubois, Alexis; Ricote, Sandrine; Braun, Robert J.

2017-11-01

Recent progress in the performance of intermediate temperature (500-600 °C) protonic ceramic fuel cells (PCFCs) has demonstrated both fuel flexibility and increasing power density that approach commercial application requirements. These developments may eventually position the technology as a viable alternative to solid oxide fuel cells (SOFCs) and molten carbonate fuel cells (MCFCs). The PCFCs investigated in this work are based on a BaZr0.8Y0.2O3-δ (BZY20) thin electrolyte supported by BZY20/Ni porous anodes, and a triple conducting cathode material comprised of BaCo0.4Fe0.4Zr0.1Y0.1O3-δ (BCFZY0.1). These cells are prepared using a low-cost solid-state reactive sintering (SSRS) process, and are capable of power densities of 0.156 W cm-2 at 500 °C operating directly from methane fuel. We develop a manufacturing cost model to estimate the Nth generation production costs of PCFC stack technology using high volume manufacturing processes and compare them to the state-of-the-art in SOFC technology. The low-cost cell manufacturing enabled by the SSRS technique compensates for the lower PCFC power density and the trade-off between operating temperature and efficiency enables the use of lower-cost stainless steel materials. PCFC stack production cost estimates are found to be as much as 27-37% lower at 550 °C than SOFCs operating at 800 °C.

Cost (non)-recovery by platform technology facilities in the Bio21 Cluster.

Science.gov (United States)

Gibbs, Gerard; Clark, Stella; Quinn, Julieanne; Gleeson, Mary Joy

2010-04-01

Platform technologies (PT) are techniques or tools that enable a range of scientific investigations and are critical to today's advanced technology research environment. Once installed, they require specialized staff for their operations, who in turn, provide expertise to researchers in designing appropriate experiments. Through this pipeline, research outputs are raised to the benefit of the researcher and the host institution. Platform facilities provide access to instrumentation and expertise for a wide range of users beyond the host institution, including other academic and industry users. To maximize the return on these substantial public investments, this wider access needs to be supported. The question of support and the mechanisms through which this occurs need to be established based on a greater understanding of how PT facilities operate. This investigation was aimed at understanding if and how platform facilities across the Bio21 Cluster meet operating costs. Our investigation found: 74% of platforms surveyed do not recover 100% of direct operating costs and are heavily subsidized by their home institution, which has a vested interest in maintaining the technology platform; platform managers play a major role in establishing the costs and pricing of the facility, normally in a collaborative process with a management committee or institutional accountant; and most facilities have a three-tier pricing structure recognizing internal academic, external academic, and commercial clients.

Estimation of costs for applications of remediation technologies for the Department of Energy's Programmatic Environmental Impact Statement

International Nuclear Information System (INIS)

Villegas, A.J.; Hansen, R.I.; Humphreys, K.K.; Paananen, J.M.; Gildea, L.F.

1994-01-01

The Programmatic Environmental impact Statement (PEIS) being developed by the US Department of Energy (DOE) for environmental restoration (ER) and waste management (WM) activities expected to be carried out across the DOE's nationwide complex of facilities is assessing the impacts of removing, transporting, treating, storing, and disposing of waste from these ER and WM activities. Factors being considered include health and safety impacts to the public and to workers, impacts on the environment, costs and socio-economic impacts, and near-term and residual risk during those ER and WM operations. The purpose of this paper is to discuss the methodology developed specifically for the PEIS to estimate costs associated with the deployment and application of individual remediation technologies. These individual costs are used in developing order-of-magnitude cost estimates for the total remediation activities. Costs are developed on a per-unit-of-material-to-be-treated basis (i.e., $/m 3 ) to accommodate remediation projects of varying sizes. The primary focus of this cost-estimating effort was the development of capital and operating unit cost factors based on the amount of primary media to be removed, handled, and treated. The unit costs for individual treatment technologies were developed using information from a variety of sources, mainly from periodicals, EPA documentation, handbooks, vendor contacts, and cost models. The unit cost factors for individual technologies were adjusted to 1991 dollars

Technologies to Support Community-Dwelling Persons With Dementia: A Position Paper on Issues Regarding Development, Usability, Effectiveness and Cost-Effectiveness, Deployment, and Ethics

Science.gov (United States)

Innes, Anthea; Mountain, Gail; Robinson, Louise; van der Roest, Henriëtte; García-Casal, J Antonio; Gove, Dianne; Thyrian, Jochen René; Evans, Shirley; Dröes, Rose-Marie; Kelly, Fiona; Kurz, Alexander; Casey, Dympna; Szcześniak, Dorota; Dening, Tom; Craven, Michael P; Span, Marijke; Felzmann, Heike; Tsolaki, Magda; Franco-Martin, Manuel

2017-01-01

Background With the expected increase in the numbers of persons with dementia, providing timely, adequate, and affordable care and support is challenging. Assistive and health technologies may be a valuable contribution in dementia care, but new challenges may emerge. Objective The aim of our study was to review the state of the art of technologies for persons with dementia regarding issues on development, usability, effectiveness and cost-effectiveness, deployment, and ethics in 3 fields of application of technologies: (1) support with managing everyday life, (2) support with participating in pleasurable and meaningful activities, and (3) support with dementia health and social care provision. The study also aimed to identify gaps in the evidence and challenges for future research. Methods Reviews of literature and expert opinions were used in our study. Literature searches were conducted on usability, effectiveness and cost-effectiveness, and ethics using PubMed, Embase, CINAHL, and PsycINFO databases with no time limit. Selection criteria in our selected technology fields were reviews in English for community-dwelling persons with dementia. Regarding deployment issues, searches were done in Health Technology Assessment databases. Results According to our results, persons with dementia want to be included in the development of technologies; there is little research on the usability of assistive technologies; various benefits are reported but are mainly based on low-quality studies; barriers to deployment of technologies in dementia care were identified, and ethical issues were raised by researchers but often not studied. Many challenges remain such as including the target group more often in development, performing more high-quality studies on usability and effectiveness and cost-effectiveness, creating and having access to high-quality datasets on existing technologies to enable adequate deployment of technologies in dementia care, and ensuring that ethical

High-cost users of medical care

OpenAIRE

Garfinkel, Steven A.; Riley, Gerald F.; Iannacchione, Vincent G.

1988-01-01

Based on data from the National Medical Care Utilization and Expenditure Survey, the 10 percent of the noninstitutionalized U.S. population that incurred the highest medical care charges was responsible for 75 percent of all incurred charges. Health status was the strongest predictor of high-cost use, followed by economic factors. Persons 65 years of age or over incurred far higher costs than younger persons and had higher out-of-pocket costs, absolutely and as a percentage of income, althoug...

TASKA-M - a low cost, near term tandem mirror device for fusion technology testing

International Nuclear Information System (INIS)

Badger, B.; Corradini, M.L.; El-Guebaly, L.; Emmert, G.A.; Kulcinski, G.L.; Larsen, E.M.; Maynard, C.W.; Perkins, L.J.; Peterson, R.R.; Plute, K.E.; Santarius, J.F.; Sawan, M.E.; Scharer, J.E.; Sviatoslavsky, I.N.; Sze, D.K.; Vogelsang, W.F.; Wittenberg, L.J.; Leppelmeier, G.W.; Grover, J.M.; Opperman, E.K.; Vogel, M.A.; Borie, E.; Taczanowski, S.; Arendt, F.; Dittrich, H.G.; Fett, T.; Haferkamp, B.; Heinz, W.; Hoelzchen, E.; Kleefeldt, K.; Klingelhoefer, R.; Komarek, P.; Kuntze, M.; Leiste, H.G.; Link, W.; Malang, S.; Manes, B.M.; Maurer, W.; Michael, I.; Mueller, R.A.; Neffe, G.; Schramm, K.; Suppan, A.; Weinberg, D.

1984-04-01

TASKA-M (Modifizierte Tandem Spiegelmaschine Karlsruhe) is a study of a dedicated fusion technology device based on the mirror principle, in continuation of the 1981/82 TASKA study. The main objective is to minimize cost while retaining key requirements of neutron flux and fluence for blanket and material development and for component testing in a nuclear environment. Direct costs are reduced to about 400 M$ by dropping reactor-relevant aspects not essential to technology testing: No thermal barrier and electrostatic plugging of the plasma; fusion power of 7 MW at an injected power of 44 MW; tritium supply from external sources. All technologies for operating the machine are expected to be available by 1990; the plasma physics relies on microstabilization in a sloshing ion population. (orig.) [de

Infusing Technology into Customer Relationships: Balancing High-Tech and High-Touch

Science.gov (United States)

Salomann, Harald; Kolbe, Lutz; Brenner, Walter

In today's business environment, self-service is becoming increasingly important. In order to promote their self-service activities, banks have created online-only products and airlines offer exclusive discounts for passengers booking online. Self-service technologies' practical applications demonstrate this approach's potential. For example, Amtrak introduced an IVR (Interactive Voice Response) system, allowing cost savings of 13m; likewise Royal Mail installed an IVR system leading to a reduction of its customer service costs by 25% (Economist 2004).

The costs and consequences of assisted reproductive technology : an economic perspective

NARCIS (Netherlands)

Connolly, Mark P.; Hoorens, Stijn; Chambers, Georgina M.

2010-01-01

Despite the growing use of assisted reproductive technologies (ART) worldwide, there is only a limited understanding of the economics of ART to inform policy about effective, safe and equitable financing of ART treatment. A review was undertaken of key studies regarding the costs and consequences of

Nuclear reactors' construction costs: The role of lead-time, standardization and technological progress

International Nuclear Information System (INIS)

Berthélemy, Michel; Escobar Rangel, Lina

2015-01-01

This paper provides an econometric analysis of nuclear reactor construction costs in France and the United States based on overnight costs data. We build a simultaneous system of equations for overnight costs and construction time (lead-time) to control for endogeneity, using change in expected electricity demand as instrument. We argue that the construction of nuclear reactors can benefit from standardization gains through two channels. First, short term coordination benefits can arise when the diversity of nuclear reactors' designs under construction is low. Second, long term benefits can occur due to learning spillovers from past constructions of similar reactors. We find that construction costs benefit directly from learning spillovers but that these spillovers are only significant for nuclear models built by the same Architect–Engineer. In addition, we show that the standardization of nuclear reactors under construction has an indirect and positive effect on construction costs through a reduction in lead-time, the latter being one of the main drivers of construction costs. Conversely, we also explore the possibility of learning by searching and find that, contrary to other energy technologies, innovation leads to construction costs increases. -- Highlights: •This paper analyses the determinants of nuclear reactors construction costs and lead-time. •We study short term (coordination gains) and long term (learning by doing) benefits of standardization in France and the US. •Results show that standardization of nuclear programs is a key factor for reducing construction costs. •We also suggest that technological progress has contributed to construction costs escalation

Systems and technologies for high-speed inter-office/datacenter interface

Science.gov (United States)

Sone, Y.; Nishizawa, H.; Yamamoto, S.; Fukutoku, M.; Yoshimatsu, T.

2017-01-01

Emerging requirements for inter-office/inter-datacenter short reach links for data center interconnects (DCI) and metro transport networks have led to various inter-office and inter-datacenter optical interface technologies. These technologies are bringing significant changes to systems and network architectures. In this paper, we present a system and ZR optical interface technologies for DCI and metro transport networks, then introduce the latest challenges facing the system framework. There are two trends in reach extension; one is to use Ethernet and the other is to use digital coherent technologies. The first approach achieves reach extension while using as many existing Ethernet components as possible. It offers low costs as reuses the cost-effective components created for the large Ethernet market. The second approach adopts low-cost and low power coherent DSPs that implement the minimal set long haul transmission functions. This paper introduces an architecture that integrates both trends. The architecture satisfies both datacom and telecom needs with a common control and management interface and automated configuration.

Achieving High Reliability with People, Processes, and Technology.

Science.gov (United States)

Saunders, Candice L; Brennan, John A

2017-01-01

High reliability as a corporate value in healthcare can be achieved by meeting the "Quadruple Aim" of improving population health, reducing per capita costs, enhancing the patient experience, and improving provider wellness. This drive starts with the board of trustees, CEO, and other senior leaders who ingrain high reliability throughout the organization. At WellStar Health System, the board developed an ambitious goal to become a top-decile health system in safety and quality metrics. To achieve this goal, WellStar has embarked on a journey toward high reliability and has committed to Lean management practices consistent with the Institute for Healthcare Improvement's definition of a high-reliability organization (HRO): one that is committed to the prevention of failure, early identification and mitigation of failure, and redesign of processes based on identifiable failures. In the end, a successful HRO can provide safe, effective, patient- and family-centered, timely, efficient, and equitable care through a convergence of people, processes, and technology.

Low Cost, High Capacity Regenerable Sorbent for Carbon Dioxide Capture from Existing Coal-fired Power Plants

Energy Technology Data Exchange (ETDEWEB)

Alptekin, Gokhan [TDA Research, Inc., Wheat Ridge, CO (United States); Jayaraman, Ambalavanan [TDA Research, Inc., Wheat Ridge, CO (United States); Dietz, Steven [TDA Research, Inc., Wheat Ridge, CO (United States)

2016-03-03

In this project TDA Research, Inc (TDA) has developed a new post combustion carbon capture technology based on a vacuum swing adsorption system that uses a steam purge and demonstrated its technical feasibility and economic viability in laboratory-scale tests and tests in actual coal derived flue gas. TDA uses an advanced physical adsorbent to selectively remove CO₂ from the flue gas. The sorbent exhibits a much higher affinity for CO₂ than N₂, H₂O or O₂, enabling effective CO₂ separation from the flue gas. We also carried out a detailed process design and analysis of the new system as part of both sub-critical and super-critical pulverized coal fired power plants. The new technology uses a low cost, high capacity adsorbent that selectively removes CO₂ in the presence of moisture at the flue gas temperature without a need for significant cooling of the flue gas or moisture removal. The sorbent is based on a TDA proprietary mesoporous carbon that consists of surface functionalized groups that remove CO₂ via physical adsorption. The high surface area and favorable porosity of the sorbent also provides a unique platform to introduce additional functionality, such as active groups to remove trace metals (e.g., Hg, As). In collaboration with the Advanced Power and Energy Program of the University of California, Irvine (UCI), TDA developed system simulation models using Aspen PlusTM simulation software to assess the economic viability of TDA’s VSA-based post-combustion carbon capture technology. The levelized cost of electricity including the TS&M costs for CO₂ is calculated as $116.71/MWh and $113.76/MWh for TDA system integrated with sub-critical and super-critical pulverized coal fired power plants; much lower than the $153.03/MWhand $147.44/MWh calculated for the corresponding amine based systems. The cost of CO₂ captured for TDA’s VSA based system is $38

Cost comparison of very high temperature nuclear reactors for process heat applications

International Nuclear Information System (INIS)

Crowley, J.H.; Newman, J.B.

1975-03-01

In April 1974, the United States Atomic Energy Commission (USAEC) authorized General Atomic Company, General Electric Company and Westinghouse Astronuclear Laboratory to assess the available technology for producing process heat utilizing very high temperature nuclear reactors. General Electric and Westinghouse produced concepts for the entire nuclear system, including the balance of plant. The General Atomic assessment included only the nuclear reactor portion of the nuclear plant. United Engineers and Constructors Inc. (UE and C) was requested by the USAEC in November 1974 to prepare an economic comparison of the three conceptual plants. The comparison is divided into three tasks: (1) Develop a balance of plant conceptual design to be combined with the General Atomic concept as a basis for comparison, and estimate the cost of the General Atomic/UE and C concept in July 1974 dollars; (2) Normalize the overall plant costs for the General Atomic/UE and C, General Electric and Westinghouse concepts, compare the costs, and identify significant differences between the concepts; and (3) Estimate the operation and maintenance costs for the General Atomic/UE and C plant and compare with the other concepts. The results of these task studies are discussed

The Need for Technology Maturity of Any Advanced Capability to Achieve Better Life Cycle Cost (LCC)

Science.gov (United States)

Robinson, John W.; Levack, Daniel J. H.; Rhodes, Russel E.; Chen, Timothy T.

2009-01-01

Programs such as space transportation systems are developed and deployed only rarely, and they have long development schedules and large development and life cycle costs (LCC). They have not historically had their LCC predicted well and have only had an effort to control the DDT&E phase of the programs. One of the factors driving the predictability, and thus control, of the LCC of a program is the maturity of the technologies incorporated in the program. If the technologies incorporated are less mature (as measured by their Technology Readiness Level - TRL), then the LCC not only increases but the degree of increase is difficult to predict. Consequently, new programs avoid incorporating technologies unless they are quite mature, generally TRL greater than or equal to 7 (system prototype demonstrated in a space environment) to allow better predictability of the DDT&E phase costs unless there is no alternative. On the other hand, technology development programs rarely develop technologies beyond TRL 6 (system/subsystem model or prototype demonstrated in a relevant environment). Currently the lack of development funds beyond TRL 6 and the major funding required for full scale development leave little or no funding available to prototype TRL 6 concepts so that hardware would be in the ready mode for safe, reliable and cost effective incorporation. The net effect is that each new program either incorporates little new technology or has longer development schedules and costs, and higher LCC, than planned. This paper presents methods to ensure that advanced technologies are incorporated into future programs while providing a greater accuracy of predicting their LCC. One method is having a dedicated organization to develop X-series vehicles or separate prototypes carried on other vehicles. The question of whether such an organization should be independent of NASA and/or have an independent funding source is discussed. Other methods are also discussed. How to make the

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to improve cell efficiency, experiments were conducted for enhancing bottom a-SiGe cell efficiency for the embodiment of an enhanced-efficiency multi-junction cell, for improving crystallinity in microcrystalline silicon through the application of VHF (very high frequency) plasma CVD (chemical vapor deposition), for texturizing metal electrodes on a film substrate, and so forth. In the effort to increase the film fabrication rate, a VHF plasma CVD device was used for studying the effect of the discharge frequency on film deposition and quality, Vpp between the electrodes, and so forth. Studies about the high-throughput production technology centered on the film substrate solar cell process technology and the designing of an optimum geometrical pattern for SCAF (series-connection through apertures formed on film) cells. Production cost was estimated for the SCAF structure film substrate solar cell manufacturing process, and a production cost of 147.1 yen/W (in case of 100 MW/year production) was obtained as achievable under the currently available conditions. (NEDO)

Assessing the high costs of new nuclear power plants

International Nuclear Information System (INIS)

Komanoff, C.

1984-01-01

The variation in nuclear plant capital costs, both over time and within the current generation of plants, is considerable and is one of the impressive facts associated with that technology. This article concerns statistical methods for determining relative management efficiency or inefficiency in nuclear plant construction. It emphasizes the need to adjust raw cost data for important variables in order to make fair comparisons among disparate projects. The analysis identifies the costliest and least-costly projects and elucidates trends that helped or harmed several or more projects at the same time. Its findings can form a supplement and guide for engineering and management audits of individual nuclear projects. 5 references, 1 figure, 1 table

Predicting Future High-Cost Schizophrenia Patients Using High-Dimensional Administrative Data

Directory of Open Access Journals (Sweden)

Yajuan Wang

2017-06-01

Full Text Available BackgroundThe burden of serious and persistent mental illness such as schizophrenia is substantial and requires health-care organizations to have adequate risk adjustment models to effectively allocate their resources to managing patients who are at the greatest risk. Currently available models underestimate health-care costs for those with mental or behavioral health conditions.ObjectivesThe study aimed to develop and evaluate predictive models for identification of future high-cost schizophrenia patients using advanced supervised machine learning methods.MethodsThis was a retrospective study using a payer administrative database. The study cohort consisted of 97,862 patients diagnosed with schizophrenia (ICD9 code 295.* from January 2009 to June 2014. Training (n = 34,510 and study evaluation (n = 30,077 cohorts were derived based on 12-month observation and prediction windows (PWs. The target was average total cost/patient/month in the PW. Three models (baseline, intermediate, final were developed to assess the value of different variable categories for cost prediction (demographics, coverage, cost, health-care utilization, antipsychotic medication usage, and clinical conditions. Scalable orthogonal regression, significant attribute selection in high dimensions method, and random forests regression were used to develop the models. The trained models were assessed in the evaluation cohort using the regression R2, patient classification accuracy (PCA, and cost accuracy (CA. The model performance was compared to the Centers for Medicare & Medicaid Services Hierarchical Condition Categories (CMS-HCC model.ResultsAt top 10% cost cutoff, the final model achieved 0.23 R2, 43% PCA, and 63% CA; in contrast, the CMS-HCC model achieved 0.09 R2, 27% PCA with 45% CA. The final model and the CMS-HCC model identified 33 and 22%, respectively, of total cost at the top 10% cost cutoff.ConclusionUsing advanced feature selection leveraging detailed

Lean VOC-Air Mixtures Catalytic Treatment: Cost-Benefit Analysis of Competing Technologies

Directory of Open Access Journals (Sweden)

Gabriele Baldissone

2017-06-01

Full Text Available Various processing routes are available for the treatment of lean VOC-air mixtures, and a cost-benefit analysis is the tool we propose to identify the most suitable technology. Two systems have been compared in this paper, namely a “traditional” plant, with a catalytic fixed-bed reactor with a heat exchanger for heat recovery purposes, and a “non-traditional” plant, with a catalytic reverse-flow reactor, where regenerative heat recovery may be achieved thanks to the periodical reversal of the flow direction. To be useful for decisions-making, the cost-benefit analysis must be coupled to the reliability, or availability, analysis of the plant. Integrated Dynamic Decision Analysis is used for this purpose as it allows obtaining the full set of possible sequences of events that could result in plant unavailability, and, for each of them, the probability of occurrence is calculated. Benefits are thus expressed in terms of out-of-services times, that have to be minimized, while the costs are expressed in terms of extra-cost for maintenance activities and recovery actions. These variable costs must be considered together with the capital (fixed cost required for building the plant. Results evidenced the pros and cons of the two plants. The “traditional” plant ensures a higher continuity of services, but also higher operational costs. The reverse-flow reactor-based plant exhibits lower operational costs, but a higher number of protection levels are needed to obtain a similar level of out-of-service. The quantification of risks and benefits allows the stakeholders to deal with a complete picture of the behavior of the plants, fostering a more effective decision-making process. With reference to the case under study and the relevant operational conditions, the regenerative system was demonstrated to be more suitable to treat lean mixtures: in terms of time losses following potential failures the two technologies are comparable (Fixed bed

COST MEASUREMENT AND COST MANAGEMENT IN TARGET COSTING

Directory of Open Access Journals (Sweden)

Moisello Anna Maria

2012-07-01

Full Text Available Firms are coping with a competitive scenario characterized by quick changes produced by internationalization, concentration, restructuring, technological innovation processes and financial market crisis. On the one hand market enlargement have increased the number and the segmentation of customers and have raised the number of competitors, on the other hand technological innovation has reduced product life cycle. So firms have to adjust their management models to this scenario, pursuing customer satisfaction and respecting cost constraints. In a context where price is a variable fixed by the market, firms have to switch from the cost measurement logic to the cost management one, adopting target costing methodology. The target costing process is a price driven, customer oriented profit planning and cost management system. It works, in a cross functional way, from the design stage throughout all the product life cycle and it involves the entire value chain. The process implementation needs a costing methodology consistent with the cost management logic. The aim of the paper is to focus on Activity Based Costing (ABC application to target costing process. So: -it analyzes target costing logic and phases, basing on a literary review, in order to highlight the costing needs related to this process; -it shows, through a numerical example, how to structure a flexible ABC model – characterized by the separation between variable, fixed in the short and fixed costs - that effectively supports target costing process in the cost measurement phase (drifting cost determination and in the target cost alignment; -it points out the effectiveness of the Activity Based Costing as a model of cost measurement applicable to the supplier choice and as a support for supply cost management which have an important role in target costing process. The activity based information allows a firm to optimize the supplier choice by following the method of minimizing the

On information and communication technology and production cost in construction industry: evidence from the Netherlands

NARCIS (Netherlands)

van der Vlist, A.J; Vrolijk, M.H.; Dewulf, Geert P.M.R.

2014-01-01

The interplay between information and communication technology (ICT) and the competitiveness of construction firms is considered. More specifically, the question is whether firms that invest in information and communication technology have a production cost advantage. The economics literature

Fluoride Salt-Cooled High-Temperature Reactor Technology Development and Demonstration Roadmap

Energy Technology Data Exchange (ETDEWEB)

Holcomb, David Eugene [ORNL; Flanagan, George F [ORNL; Mays, Gary T [ORNL; Pointer, William David [ORNL; Robb, Kevin R [ORNL; Yoder Jr, Graydon L [ORNL

2013-11-01

Fluoride salt-cooled High-temperature Reactors (FHRs) are an emerging reactor class with potentially advantageous performance characteristics, and fully passive safety. This roadmap describes the principal remaining FHR technology challenges and the development path needed to address the challenges. This roadmap also provides an integrated overview of the current status of the broad set of technologies necessary to design, evaluate, license, construct, operate, and maintain FHRs. First-generation FHRs will not require any technology breakthroughs, but do require significant concept development, system integration, and technology maturation. FHRs are currently entering early phase engineering development. As such, this roadmap is not as technically detailed or specific as would be the case for a more mature reactor class. The higher cost of fuel and coolant, the lack of an approved licensing framework, the lack of qualified, salt-compatible structural materials, and the potential for tritium release into the environment are the most obvious issues that remain to be resolved.

PERFORMANCE AND COST OF MERCURY AND MULTIPOLLUTANT EMISSION CONTROL TECHNOLOGY APPLICATIONS ON ELECTRIC UTILITY BOILERS

Science.gov (United States)

The report presents estimates of the performance and cost of both powdered activated carbon (PAC) and multipollutant control technologies that may be useful in controlling mercury emissions. Based on currently available data, cost estimates for PAC injection range are 0.03-3.096 ...

Modelling diffusion feedbacks between technology performance, cost and consumer behaviour for future energy-transport systems

Science.gov (United States)

Tran, Martino; Brand, Christian; Banister, David

2014-04-01

Emerging technologies will have important impacts on sustainability objectives. Yet little is known about the explicit feedbacks between consumer behaviour and technological change, and the potential impact on mass market penetration. We use the UK as a case-study to explore the dynamic interactions between technology supply, performance, cost, and heterogeneous consumer behaviour and the resulting influence on long term market diffusion. Simulations of competing vehicle technologies indicate that petrol hybrids (HEVs) dominate the market over the long-term because they benefit from improved performance and are able to reach the steep part of the diffusion curve by 2025 while competing technologies remain in the early stages of growth and are easier to displace in the market. This is due to the cumulative build-up of stock and slow fleet turnover creating inertia in the technological system. Consequently, it will be difficult to displace incumbent technologies because of system inertia, cumulative growth in stock, long operational life, and consumer risk aversion to new unproven technologies. However, when accounting for both technological and behavioural change, simulations indicate that if investment can reach 30-40% per annum growth in supply, combined with steady technology improvements, and more sophisticated agent decision making such as accounting for full technology lifecycle cost and performance, full battery electric vehicles could displace the incumbent system by 2050.

Levelised unit electricity cost comparison of alternate technologies for baseload generation in Ontario

International Nuclear Information System (INIS)

Ayres, M.; McRae, M.; Stogran, M.

2004-08-01

This report provides a comparison of the lifetime cost of constructing, operating and decommissioning new generation suitable for supplying baseload power by early in the next decade. New baseload generation options in Ontario are nuclear, coal-fired steam turbines or combined cycle gas turbines (CCGT). Nuclear and coal-fired units are characterised by high capital costs and low operating costs. As such, they are candidates for baseload operation only. Gas-fired generation is characterised by lower capital costs and higher operating costs and thus may meet the requirements for operation as peaking and/or baseload generation. The comparison of baseload generating technologies is made by reference to the estimated levelised unit electricity cost (LUEC). The LUEC can be thought of as a 'supply cost', where the unit cost is the price needed to recover all costs over the period. It is determined by finding the price that sets the sum of all future discounted cash flows (net present value, or NPV) to zero. It can also be thought of as representing the constant real wholesale price of electricity that meets the financing cost, debt repayment, income tax and cash flow constraints associated with the construction operation and decommissioning of a generating plant. Levelised unit cost comparisons are usually made with different sets of financing assumptions. This report considers two base cases, which we describe as 'merchant' and 'public' financing. The term 'merchant plant' is used to refer to ones that are built and operated by private investors. These investors pay for their capital through debt and by raising equity, and thus pay return on equity and interest on debt throughout their lifetime. These projects include income taxes, both provincial and federal. Publicly financed projects typically are not subject to income taxes or to the same constraints on raising finance through issuing debt and equity. However, they are constrained to provide a rate of return. The

Assessing Risk in Costing High-energy Accelerators: from Existing Projects to the Future Linear Collider

CERN Document Server

Lebrun, Philippe

2010-01-01

High-energy accelerators are large projects funded by public money, developed over the years and constructed via major industrial contracts both in advanced technology and in more conventional domains such as civil engineering and infrastructure, for which they often constitute one-of markets. Assessing their cost, as well as the risk and uncertainty associated with this assessment is therefore an essential part of project preparation and a justified requirement by the funding agencies. Stemming from the experience with large circular colliders at CERN, LEP and LHC, as well as with the Main Injector, the Tevatron Collider Experiments and Accelerator Upgrades, and the NOvA Experiment at Fermilab, we discuss sources of cost variance and derive cost risk assessment methods applicable to the future linear collider, through its two technical approaches for ILC and CLIC. We also address disparities in cost risk assessment imposed by regional differences in regulations, procedures and practices.

Strategic Health Technology Incorporation

CERN Document Server

Wang, Binseng

2009-01-01

Technology is essential to the delivery of health care but it is still only a tool that needs to be deployed wisely to ensure beneficial outcomes at reasonable costs. Among various categories of health technology, medical equipment has the unique distinction of requiring both high initial investments and costly maintenance during its entire useful life. This characteristic does not, however, imply that medical equipment is more costly than other categories, provided that it is managed properly. The foundation of a sound technology management process is the planning and acquisition of equipment

Designing Cost-Competitive Technology Products through Cost Management

NARCIS (Netherlands)

Davila, T.; Wouters, Marc

2004-01-01

SYNOPSIS: As manufacturing innovations spread throughout leading organizations, product development becomes a more important source of competitive advantage. Within product development, cost management receives increasing attention. To date, cost management in new product development focuses

High Efficiency and Low Cost Thermal Energy Storage System

Energy Technology Data Exchange (ETDEWEB)

Sienicki, James J. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Lv, Qiuping [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Moisseytsev, Anton [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Bucknor, Matthew [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division

2017-09-29

BgtL, LLC (BgtL) is focused on developing and commercializing its proprietary compact technology for processes in the energy sector. One such application is a compact high efficiency Thermal Energy Storage (TES) system that utilizes the heat of fusion through phase change between solid and liquid to store and release energy at high temperatures and incorporate state-of-the-art insulation to minimize heat dissipation. BgtL’s TES system would greatly improve the economics of existing nuclear and coal-fired power plants by allowing the power plant to store energy when power prices are low and sell power into the grid when prices are high. Compared to existing battery storage technology, BgtL’s novel thermal energy storage solution can be significantly less costly to acquire and maintain, does not have any waste or environmental emissions, and does not deteriorate over time; it can keep constant efficiency and operates cleanly and safely. BgtL’s engineers are experienced in this field and are able to design and engineer such a system to a specific power plant’s requirements. BgtL also has a strong manufacturing partner to fabricate the system such that it qualifies for an ASME code stamp. BgtL’s vision is to be the leading provider of compact systems for various applications including energy storage. BgtL requests that all technical information about the TES designs be protected as proprietary information. To honor that request, only non-proprietay summaries are included in this report.

Cost-effective, transfer-free, flexible resistive random access memory using laser-scribed reduced graphene oxide patterning technology.

Science.gov (United States)

Tian, He; Chen, Hong-Yu; Ren, Tian-Ling; Li, Cheng; Xue, Qing-Tang; Mohammad, Mohammad Ali; Wu, Can; Yang, Yi; Wong, H-S Philip

2014-06-11

Laser scribing is an attractive reduced graphene oxide (rGO) growth and patterning technology because the process is low-cost, time-efficient, transfer-free, and flexible. Various laser-scribed rGO (LSG) components such as capacitors, gas sensors, and strain sensors have been demonstrated. However, obstacles remain toward practical application of the technology where all the components of a system are fabricated using laser scribing. Memory components, if developed, will substantially broaden the application space of low-cost, flexible electronic systems. For the first time, a low-cost approach to fabricate resistive random access memory (ReRAM) using laser-scribed rGO as the bottom electrode is experimentally demonstrated. The one-step laser scribing technology allows transfer-free rGO synthesis directly on flexible substrates or non-flat substrates. Using this time-efficient laser-scribing technology, the patterning of a memory-array area up to 100 cm(2) can be completed in 25 min. Without requiring the photoresist coating for lithography, the surface of patterned rGO remains as clean as its pristine state. Ag/HfOx/LSG ReRAM using laser-scribing technology is fabricated in this work. Comprehensive electrical characteristics are presented including forming-free behavior, stable switching, reasonable reliability performance and potential for 2-bit storage per memory cell. The results suggest that laser-scribing technology can potentially produce more cost-effective and time-effective rGO-based circuits and systems for practical applications.

Technology in Community-Based Organizations that Serve Older People: High Tech Meets High Touch

Science.gov (United States)

Renold, Carl; Meronk, Cheryl; Kelly, Christopher

2005-01-01

Appropriate implementation of information technology (IT) can help create a more efficient, less costly, and higher-quality service-delivery environment for community-based organizations that serve older people. Relevant studies and reports on technology in healthcare can be compared and applied to these organizations. This study is the result of…

High SO{sub 2} removal duct injection: A low-cost FGD alternative

Energy Technology Data Exchange (ETDEWEB)

Nelson, S.G. [Sorbent Technologies Corp., Twinsburg, OH (United States)

1995-12-01

Sorbent Technologies Corporation, of the United States, is currently developing and demonstrating a new waste free, retrofitable, high-SO{sub 2} removal duct-injection process. Up to 85 percent SO{sub 2} removal is achieved by simply injecting a new dry lime-based sorbent into the flue-gas duct, collecting the sorbent downstream in a particulate collector, and then recycling the sorbent. By avoiding large, expensive components, the process can have low capital costs, making it especially appropriate for smaller, older, less-utilized plants. The key to the new technology is the use of sorbent supports. Supported sorbents are produced by coating hydrated lime onto inexpensive mineral supports, such as exfoliated vermiculite or perlite. Consequently, there are no liquid, sludge, or solid wastes with the new technology. Once saturated with SO{sub 2}, the spent sorbent can be easily pelletized into a valuable soil-conditioning agricultural by-product, for the sustainable development that the future requires. This paper describes Sorbent Technologies` pilot demonstration of supported sorbent injection at the Ohio Edison Company`s R.E. Burger station. The Burger effort is also the first demonstration of the Electric Power Research Institute`s new {open_quotes}COHPAC{close_quotes} baghouse technology in a sorbent-injection desulfurization application.

Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

Energy Technology Data Exchange (ETDEWEB)

Bill Stanley; Sandra Brown; Patrick Gonzalez; Brent Sohngen; Neil Sampson; Mark Anderson; Miguel Calmon; Sean Grimland; Ellen Hawes; Zoe Kant; Dan Morse; Sarah Woodhouse Murdock; Arlene Olivero; Tim Pearson; Sarah Walker; Jon Winsten; Chris Zganjar

2006-09-30

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between April 1st and July 30th 2006. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.

Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

Energy Technology Data Exchange (ETDEWEB)

Bill Stanley; Patrick Gonzalez; Sandra Brown; Jenny Henman; Zoe Kant; Sarah Woodhouse Murdock; Neil Sampson; Gilberto Tiepolo; Tim Pearson; Sarah Walker; Miguel Calmon

2006-01-01

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between April 1st , 2005 and June 30th, 2005. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.

Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

Energy Technology Data Exchange (ETDEWEB)

Bill Stanley; Patrick Gonzalez; Sandra Brown; Jenny Henman; Sarah Woodhouse Murdock; Neil Sampson; Tim Pearson; Sarah Walker; Zoe Kant; Miguel Calmon

2006-04-01

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between January 1st and March 31st 2006. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.

Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

Energy Technology Data Exchange (ETDEWEB)

Bill Stanley; Sandra Brown; Patrick Gonzalez; Brent Sohngen; Neil Sampson; Mark Anderson; Miguel Calmon; Sean Grimland; Zoe Kant; Dan Morse; Sarah Woodhouse Murdock; Arlene Olivero; Tim Pearson; Sarah Walker; Jon Winsten; Chris Zganjar

2007-03-31

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between January 1st and March 31st 2007. The specific tasks discussed include: Task 1--carbon inventory advancements; Task 2--emerging technologies for remote sensing of terrestrial carbon; Task 3--baseline method development; Task 4--third-party technical advisory panel meetings; Task 5--new project feasibility studies; and Task 6--development of new project software screening tool.

Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

Energy Technology Data Exchange (ETDEWEB)

Bill Stanley; Patrick Gonzalez; Sandra Brown; Sarah Woodhouse Murdock; Jenny Henman; Zoe Kant; Gilberto Tiepolo; Tim Pearson; Neil Sampson; Miguel Calmon

2005-10-01

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between April 1st , 2005 and June 30th, 2005. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.

Additively Manufactured Low Cost Upper Stage Combustion Chamber

Science.gov (United States)

Protz, Christopher; Cooper, Ken; Ellis, David; Fikes, John; Jones, Zachary; Kim, Tony; Medina, Cory; Taminger, Karen; Willingham, Derek

2016-01-01

Over the past two years NASA's Low Cost Upper Stage Propulsion (LCUSP) project has developed Additive Manufacturing (AM) technologies and design tools aimed at reducing the costs and manufacturing time of regeneratively cooled rocket engine components. High pressure/high temperature combustion chambers and nozzles must be regeneratively cooled to survive their operating environment, causing their design fabrication to be costly and time consuming due to the number of individual steps and different processes required. Under LCUSP, AM technologies in Sintered Laser Melting (SLM) GRCop-84 and Electron Beam Freeform Fabrication (EBF3) Inconel 625 have been significantly advanced, allowing the team to successfully fabricate a 25k-class regenerative chamber. Estimates of the costs and schedule of future builds indicate cost reductions and significant schedule reductions will be enabled by this technology. Characterization of the microstructural and mechanical properties of the SLM-produced GRCop-84, EBF3 Inconel 625 and the interface layer between the two has been performed and indicates the properties will meet the design requirements. The LCUSP chamber is to be tested with a previously demonstrated SLM injector in order to advance the Technology Readiness Level (TRL) and demonstrate the capability of the application of these processes. NASA is advancing these technologies to reduce cost and schedule for future engine applications and commercial needs.

Role of high technology in the nuclear industry

International Nuclear Information System (INIS)

Cain, D.G.

1986-01-01

A discussion of high technology identifies the characteristics which distinguish it from conventional technologies, and the impact high technology will have in the nuclear power industry in the near future. The basic theme is that high technology is an ensemble of competing technological developments that shifts with time and technological innovation. The attributes which current distinguish high technology are compactness, plasticity, convergence, and intelligence. These high technology attributes are presented as a prelude to some examples of high technology developments which are just beginning to penetrate the nuclear industry. Concluding remarks address some of the challenges which must be faced in order to assure that high technology is successfully adapted and used

CRADA with United Solar Technologies and Pacific Northwest Laboratory (PNL-021): Thin film materialsfor low-cost high performance solar concentrators

Science.gov (United States)

Martin, P. M.; Affinito, J. D.; Gross, M. E.; Bennett, W. D.

1995-03-01

The objectives of this project were to develop and evaluate promising low-cost dielectric and polymer-protected thin-film reflective metal coatings to be applied to preformed continuously-curved solar reflector panels to enhance their solar reflectance, and to demonstrate protected solar reflective coatings on preformed solar concentrator panels. The opportunity for this project arose from a search by United Solar Technologies (UST) for organizations and facilities capable of applying reflective coatings to large preformed panels. PNL was identified as being uniquely qualified to participate in this collaborative project.

Capital cost: high and low sulfur coal plants-1200 MWe. [High sulfur coal

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

This Commercial Electric Power Cost Study for 1200 MWe (Nominal) high and low sulfur coal plants consists of three volumes. The high sulfur coal plant is described in Volumes I and II, while Volume III describes the low sulfur coal plant. The design basis and cost estimate for the 1232 MWe high sulfur coal plant is presented in Volume I, and the drawings, equipment list and site description are contained in Volume II. The reference design includes a lime flue gas desulfurization system. A regenerative sulfur dioxide removal system using magnesium oxide is also presented as an alternate in Section 7 Volume II. The design basis, drawings and summary cost estimate for a 1243 MWe low sulfur coal plant are presented in Volume III. This information was developed by redesigning the high sulfur coal plant for burning low sulfur sub-bituminous coal. These coal plants utilize a mechanical draft (wet) cooling tower system for condenser heat removal. Costs of alternate cooling systems are provided in Report No. 7 in this series of studies of costs of commercial electrical power plants.

Process cost and facility considerations in the selection of primary cell culture clarification technology.

Science.gov (United States)

Felo, Michael; Christensen, Brandon; Higgins, John

2013-01-01

The bioreactor volume delineating the selection of primary clarification technology is not always easily defined. Development of a commercial scale process for the manufacture of therapeutic proteins requires scale-up from a few liters to thousands of liters. While the separation techniques used for protein purification are largely conserved across scales, the separation techniques for primary cell culture clarification vary with scale. Process models were developed to compare monoclonal antibody production costs using two cell culture clarification technologies. One process model was created for cell culture clarification by disc stack centrifugation with depth filtration. A second process model was created for clarification by multi-stage depth filtration. Analyses were performed to examine the influence of bioreactor volume, product titer, depth filter capacity, and facility utilization on overall operating costs. At bioreactor volumes 5,000 L, clarification using centrifugation followed by depth filtration offers significant cost savings. For bioreactor volumes of ∼ 2,000 L, clarification costs are similar between depth filtration and centrifugation. At this scale, factors including facility utilization, available capital, ease of process development, implementation timelines, and process performance characterization play an important role in clarification technology selection. In the case study presented, a multi-product facility selected multi-stage depth filtration for cell culture clarification at the 500 and 2,000 L scales of operation. Facility implementation timelines, process development activities, equipment commissioning and validation, scale-up effects, and process robustness are examined. © 2013 American Institute of Chemical Engineers.

Reduction in Fabrication Costs of Gas Diffusion Layers

Energy Technology Data Exchange (ETDEWEB)

Jason Morgan; Donald Connors; Michael Hickner

2012-07-10

Ballard Material Products (BMP) performed a pre-design technical and cost analysis of state of the art production technologies feasible for high volume GDL manufacturing. Based upon criteria that also included environmental health and safety, customer quality requirements, and future needs, BMP selected technologies that can be integrated into its current manufacturing process. These selections included Many-At-A-Time (MAAT) coating and continuous mixing technologies, as well as various on-line process control tools. These processes have allowed BMP to produce high performance GDLs at lower cost for near-term markets, as well as to define the inputs needed to develop a conceptual Greenfield facility to meet the cost targets for automotive volumes of 500,000 vehicles per year.

Evaluation of Costs in Asparagus Production in Relation to Different Technological Processes in Conditions of Slovak Republic

Directory of Open Access Journals (Sweden)

Patrik Burg

2014-01-01

Full Text Available This study deals with analysis structure of cost on the production of asparagus in relation to three different technological processes in conditions of Slovak Republic. Obtained results can be used as a template to prepare budgets and make production decisions to estimate potential returns and to analyze investment and financial analysis decisions in the asparagus cultivation. Production practices used in the budget are based on typical practices for asparagus in this country. From the analysis of the cost structure of assessed variants different technological procedures follows that the largest share of the costs fall to purchased material and labor.

Energy and cost saving results for advanced technology systems from the Cogeneration Technology Alternatives Study (CTAS)

Science.gov (United States)

Sagerman, G. D.; Barna, G. J.; Burns, R. K.

1979-01-01

An overview of the organization and methodology of the Cogeneration Technology Alternatives Study is presented. The objectives of the study were to identify the most attractive advanced energy conversion systems for industrial cogeneration applications in the future and to assess the advantages of advanced technology systems compared to those systems commercially available today. Advanced systems studied include steam turbines, open and closed cycle gas turbines, combined cycles, diesel engines, Stirling engines, phosphoric acid and molten carbonate fuel cells and thermionics. Steam turbines, open cycle gas turbines, combined cycles, and diesel engines were also analyzed in versions typical of today's commercially available technology to provide a base against which to measure the advanced systems. Cogeneration applications in the major energy consuming manufacturing industries were considered. Results of the study in terms of plant level energy savings, annual energy cost savings and economic attractiveness are presented for the various energy conversion systems considered.

ABC model and the management of costs

Directory of Open Access Journals (Sweden)

Pravdić Predrag

2016-01-01

Full Text Available When a company has multiple objectives at the same time, they all must be considered and balanced when making any business decisions. Linking the markets, capital and resources so as to thus ensure the highest yield is, In fact, the search for competitive advantage as a basic condition for survival in a market economy. In highly detailed systems based on the management of costs or ABC (activity based costing systems, the cost of activities often result in erroneous evaluation of aggregate costs of the action. Improvements in information technology and monitoring decrease of technology costs enabled the ABC system to become a feasible system calculating costs in many organizations.

Technologies to Support Community-Dwelling Persons With Dementia: A Position Paper on Issues Regarding Development, Usability, Effectiveness and Cost-Effectiveness, Deployment, and Ethics.

Science.gov (United States)

Meiland, Franka; Innes, Anthea; Mountain, Gail; Robinson, Louise; van der Roest, Henriëtte; García-Casal, J Antonio; Gove, Dianne; Thyrian, Jochen René; Evans, Shirley; Dröes, Rose-Marie; Kelly, Fiona; Kurz, Alexander; Casey, Dympna; Szcześniak, Dorota; Dening, Tom; Craven, Michael P; Span, Marijke; Felzmann, Heike; Tsolaki, Magda; Franco-Martin, Manuel

2017-01-16

With the expected increase in the numbers of persons with dementia, providing timely, adequate, and affordable care and support is challenging. Assistive and health technologies may be a valuable contribution in dementia care, but new challenges may emerge. The aim of our study was to review the state of the art of technologies for persons with dementia regarding issues on development, usability, effectiveness and cost-effectiveness, deployment, and ethics in 3 fields of application of technologies: (1) support with managing everyday life, (2) support with participating in pleasurable and meaningful activities, and (3) support with dementia health and social care provision. The study also aimed to identify gaps in the evidence and challenges for future research. Reviews of literature and expert opinions were used in our study. Literature searches were conducted on usability, effectiveness and cost-effectiveness, and ethics using PubMed, Embase, CINAHL, and PsycINFO databases with no time limit. Selection criteria in our selected technology fields were reviews in English for community-dwelling persons with dementia. Regarding deployment issues, searches were done in Health Technology Assessment databases. According to our results, persons with dementia want to be included in the development of technologies; there is little research on the usability of assistive technologies; various benefits are reported but are mainly based on low-quality studies; barriers to deployment of technologies in dementia care were identified, and ethical issues were raised by researchers but often not studied. Many challenges remain such as including the target group more often in development, performing more high-quality studies on usability and effectiveness and cost-effectiveness, creating and having access to high-quality datasets on existing technologies to enable adequate deployment of technologies in dementia care, and ensuring that ethical issues are considered an important topic

Environmental performance review and cost analysis of MSW landfilling by baling-wrapping technology versus conventional system

International Nuclear Information System (INIS)

Baldasano, J.M.; Gasso, S.; Perez, C.

2003-01-01

This paper first reviews the chemical, physical and biological processes, and the environmental performance of MSW compacted and plastic-wrapped into air-tight bales with low-density polyethylene (LDPE). The baling-wrapping process halts the short and half-term biological activity and consequently the emission of gases and leachates. It also facilitates the handling of the refuse, and considerably reduces the main environmental impacts of a landfill. The main technologies available for baling-wrapping MSW are also presented. Furthermore, a cost analysis comparing a conventional landfill (CL) without baling system versus two landfills using different baling-wrapping technologies (rectangular and cylindrical bales) is carried out. The results are presented comparatively under the conditions of construction, operation and maintenance and postclosure, as required by European Directive 1999/31. A landfill using rectangular plastic-wrapped bales (LRPB) represents an economically competitive option compared to a CL. The increased capacity of the waste disposal zone when using rectangular bales due to the high density of the bales compensates for the increased operating and maintenance (O and M) costs of the method. Landfills using cylindrical plastic-wrapped bales (LCPB's) do not fare so well, mainly because the density within the bales is lower, the cylindrical geometry of the bales does not allow such an efficient use of the space within the landfill, and the processing capacity of the machinery is lower. From the cost model, the resulting unit costs per tonne in a LRPB, a LCPB and a CL for 100,000 t/year of waste, an operation time of 15 years and a landfill depth (H) of 20 m, are 31.52, 43.36 and 31.83 Euro/t, respectively

Cost characteristics of tilt-rotor, conventional air and high speed rail short-haul intercity passenger service

Science.gov (United States)

Schoendorfer, David L.; Morlok, Edward K.

1985-01-01

The cost analysis done to support an assessment of the potential for a small tilt-rotor aircraft to operate in short-haul intercity passenger service is described in detail. Anticipated costs of tilt-rotor air service were compared to the costs of two alternatives: conventional air and high speed rail (HSR). Costs were developed for corridor service, varying key market characteristics including distance, passenger volumes, and minimum frequency standards. The resulting cost vs output information can then be used to compare modal costs for essentially identical service quality and passenger volume or for different service levels and volumes for each mode, as appropriate. Extensive sensitivity analyses are performed. The cost-output features of these technologies are compared. Tilt-rotor is very attractive compared to HSR in terms of costs over the entire range of volume. It also has costs not dramatically different from conventional air, but tilt-rotor costs are generally higher. Thus some of its other advantages, such as the VTOL capability, must offset the cost disadvantage for it to be a preferred or competitive mode in any given market. These issues are addressed in the companion report which considers strategies for tilt-rotor development in commercial air service.

A low cost, high performance, 1.2m off-axis telescope built with NG-Xinetics silicon carbide

Science.gov (United States)

Rey, Justin J.; Wellman, John A.; Egan, Richard G.; Wollensak, Richard J.

2011-09-01

The search for extrasolar habitable planets is one of three major astrophysics priorities identified for the next decade. These missions demand very high performance visible-wavelength optical imaging systems. Such high performance space telescopes are typically extremely expensive and can be difficult for government agencies to afford in today's economic climate, and most lower cost systems offer little benefit because they fall short on at least one of the following three key performance parameters: imaging wavelength, total system-level wavefront error and aperture diameter. Northrop Grumman Xinetics has developed a simple, lightweight, low-cost telescope design that will address the near-term science objectives of this astrophysics theme with the required optical performance, while reducing the telescope cost by an order of magnitude. Breakthroughs in SiC mirror manufacturing, integrated wavefront sensing, and high TRL deformable mirror technology have finally been combined within the same organization to offer a complete end-to-end telescope system in the lower end of the Class D cost range. This paper presents the latest results of real OAP polishing and metrology data, an optimized optical design, and finite element derived WFE

APPLICATION AND DEVELOPMENT OF APPROPRIATE TOOLS AND TECHNOLOGIES FOR COST-EFFECTIVE CARBON

Energy Technology Data Exchange (ETDEWEB)

Bill Stanley; Sandra Brown; Ellen Hawes; Zoe Kant; Miguel Calmon; Patrick Gonzalez; Brad Kreps; Gilberto Tiepolo

2003-09-01

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas impacts. The research described in this report occurred between July 1, 2002 and June 30, 2003. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: advanced videography testing; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.

Cost-effectiveness of high-efficiency appliances in the U.S. residential sector: A case study

International Nuclear Information System (INIS)

McNeil, Michael A.; Bojda, Nicholas

2012-01-01

This paper presents an analysis of the cost-effectiveness of high-efficiency appliances in the U.S. residential sector using cost and efficiency data developed as part of the regulatory process of the U.S. Department of Energy's Appliances and Commercial Equipment Standards Program. These data are presented as a case study in the development of an ‘efficiency technology database’ which can be expanded and published as a resource to other researchers and policy makers seeking scenarios that optimize efficiency policies and forecast their likely impacts on energy demand and greenhouse gas emissions. The use of this data to evaluate cost-effectiveness according to a variety of metrics is demonstrated using the example of one refrigerator–freezer product class. Cost-effectiveness is then evaluated in terms of cost of conserved energy for refrigerators, room air conditioners, water heaters, cooking equipment, central air conditioners and gas furnaces. The resulting potential of cost-effective improvement ranges from 1% to 53% of energy savings, with a typical potential of 15–20%. - Highlights: ► We determined the potential for cost-effective efficiency for residential appliances. ► We cover 6 appliance groups using cost of conserved energy as a metric for cost-effectiveness. ► Data are source from the DOE's Appliance and Commercial Equipment Standards Program. ► Between 15% and 20% additional cost-effective efficiency improvement is possible.

Developing Information on Energy Savings and Associated Costs and Benefits of Energy Efficient Emerging Technologies Applicable in California

Energy Technology Data Exchange (ETDEWEB)

Xu, Tengfang; Slaa, Jan Willem; Sathaye, Jayant

2010-12-15

Implementation and adoption of efficient end-use technologies have proven to be one of the key measures for reducing greenhouse gas (GHG) emissions throughout the industries. In many cases, implementing energy efficiency measures is among one of the most cost effective investments that the industry could make in improving efficiency and productivity while reducing carbon dioxide (CO2) emissions. Over the years, there have been incentives to use resources and energy in a cleaner and more efficient way to create industries that are sustainable and more productive. With the working of energy programs and policies on GHG inventory and regulation, understanding and managing the costs associated with mitigation measures for GHG reductions is very important for the industry and policy makers around the world and in California. Successful implementation of applicable emerging technologies not only may help advance productivities, improve environmental impacts, or enhance industrial competitiveness, but also can play a significant role in climate-mitigation efforts by saving energy and reducing the associated GHG emissions. Developing new information on costs and savings benefits of energy efficient emerging technologies applicable in California market is important for policy makers as well as the industries. Therefore, provision of timely evaluation and estimation of the costs and energy savings potential of emerging technologies applicable to California is the focus of this report. The overall goal of the project is to identify and select a set of emerging and under-utilized energy-efficient technologies and practices as they are important to reduce energy consumption in industry while maintaining economic growth. Specifically, this report contains the results from performing Task 3 Technology Characterization for California Industries for the project titled Research Opportunities in Emerging and Under-Utilized Energy-Efficient Industrial Technologies, sponsored by

Gas phase adsorption technology for nitrogen isotope separation and its feasibility for highly enriched nitrogen gas production

International Nuclear Information System (INIS)

Inoue, Masaki; Asaga, Takeo

2000-04-01

Highly enriched nitrogen-15 gas is favorable to reduce radioactive carbon-14 production in reactor. The cost of highly enriched nitrogen-15 gas in mass production is one of the most important subject in nitride fuel option in 'Feasibility Study for FBR and Related Fuel Cycle'. In this work gas phase adsorption technology was verified to be applicable for nitrogen isotope separation and feasible to produce highly enriched nitrogen-15 gas in commercial. Nitrogen isotopes were separated while ammonia gas flows through sodium-A type zeolite column using pressure swing adsorption process. The isotopic ratio of eight samples were measured by high resolution mass spectrometry and Fourier transform microwave spectroscopy. Gas phase adsorption technology was verified to be applicable for nitrogen isotope separation, since the isotopic ratio of nitrogen-15 and nitrogen-14 in samples were more than six times as high as in natural. The cost of highly enriched nitrogen-15 gas in mass production were estimated by the factor method. It revealed that highly enriched nitrogen-15 gas could be supplied in a few hundred yen per gram in mass production. (author)

Cost incentives for doctors

DEFF Research Database (Denmark)

Schottmüller, Christoph

2013-01-01

If doctors take the costs of treatment into account when prescribing medication, their objectives differ from their patients' objectives because the patients are insured. This misalignment of interests hampers communication between patient and doctor. Giving cost incentives to doctors increases...... welfare if (i) the doctor's examination technology is sufficiently good or (ii) (marginal) costs of treatment are high enough. If the planner can costlessly choose the extent to which doctors take costs into account, he will opt for less than 100%. Optimal health care systems should implement different...... degrees of cost incentives depending on type of disease and/or doctor....

High performance fuel technology development

Energy Technology Data Exchange (ETDEWEB)

Koon, Yang Hyun; Kim, Keon Sik; Park, Jeong Yong; Yang, Yong Sik; In, Wang Kee; Kim, Hyung Kyu [KAERI, Daejeon (Korea, Republic of)

2012-01-15

{omicron} Development of High Plasticity and Annular Pellet - Development of strong candidates of ultra high burn-up fuel pellets for a PCI remedy - Development of fabrication technology of annular fuel pellet {omicron} Development of High Performance Cladding Materials - Irradiation test of HANA claddings in Halden research reactor and the evaluation of the in-pile performance - Development of the final candidates for the next generation cladding materials. - Development of the manufacturing technology for the dual-cooled fuel cladding tubes. {omicron} Irradiated Fuel Performance Evaluation Technology Development - Development of performance analysis code system for the dual-cooled fuel - Development of fuel performance-proving technology {omicron} Feasibility Studies on Dual-Cooled Annular Fuel Core - Analysis on the property of a reactor core with dual-cooled fuel - Feasibility evaluation on the dual-cooled fuel core {omicron} Development of Design Technology for Dual-Cooled Fuel Structure - Definition of technical issues and invention of concept for dual-cooled fuel structure - Basic design and development of main structure components for dual- cooled fuel - Basic design of a dual-cooled fuel rod.

The costs and consequences of assisted reproductive technology: an economic perspective.

Science.gov (United States)

Connolly, Mark P; Hoorens, Stijn; Chambers, Georgina M

2010-01-01

Despite the growing use of assisted reproductive technologies (ART) worldwide, there is only a limited understanding of the economics of ART to inform policy about effective, safe and equitable financing of ART treatment. A review was undertaken of key studies regarding the costs and consequences of ART treatment, specifically examining the direct and indirect costs of treatment, economic drivers of utilization and clinical practice and broader economic consequences of ART-conceived children. The direct costs of ART treatment vary substantially between countries, with the USA standing out as the most expensive. The direct costs generally reflect the costliness of the underlying healthcare system. If unsubsidized, direct costs represent a significant economic burden to patients. The level of affordability of ART treatment is an important driver of utilization, treatment choices, embryo transfer practices and ultimately multiple birth rates. The costs associated with caring for multiple-birth ART infants and their mothers are substantial, reflecting the underlying morbidity associated with such pregnancies. Investment analysis of ART treatment and ART-conceived children indicates that appropriate funding of ART services appears to represent sound fiscal policy. The complex interaction between the cost of ART treatment and how treatments are subsidized in different healthcare settings and for different patient groups has far-reaching consequences for ART utilization, clinical practice and infant outcomes. A greater understanding of the economics of ART is needed to inform policy decisions and to ensure the best possible outcomes from ART treatment.

Potential Offshore Wind Energy Areas in California: An Assessment of Locations, Technology, and Costs

Energy Technology Data Exchange (ETDEWEB)

Musial, Walter [National Renewable Energy Lab. (NREL), Golden, CO (United States); Beiter, Philipp [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tegen, Suzanne [National Renewable Energy Lab. (NREL), Golden, CO (United States); Smith, Aaron [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-12-01

This report summarizes a study of possible offshore wind energy locations, technologies, and levelized cost of energy in the state of California between 2015 and 2030. The study was funded by the U.S. Department of the Interior's Bureau of Ocean Energy Management (BOEM), the federal agency responsible for regulating renewable energy development on the Outer Continental Shelf. It is based on reference wind energy areas where representative technology and performance characteristics were evaluated. These reference areas were identified as sites that were suitable to represent offshore wind cost and technology based on physical site conditions, wind resource quality, known existing site use, and proximity to necessary infrastructure. The purpose of this study is to assist energy policy decision-making by state utilities, independent system operators, state government officials and policymakers, BOEM, and its key stakeholders. The report is not intended to serve as a prescreening exercise for possible future offshore wind development.

Renewable Energies and CO2 Cost Analysis, Environmental Impacts and Technological Trends- 2012 Edition

CERN Document Server

Guerrero-Lemus, Ricardo

2013-01-01

Providing up-to-date numerical data across a range of topics related to renewable energy technologies, Renewable Energies and CO2 offers a one-stop source of key information to engineers, economists and all other professionals working in the energy and climate change sectors. The most relevant up-to-date numerical data are exposed in 201 tables and graphs, integrated in terms of units and methodology, and covering topics such as energy system capacities and lifetimes, production costs, energy payback ratios, carbon emissions, external costs, patents and literature statistics. The data are first presented and then analyzed to project potential future grid, heat and fuel parity scenarios, as well as future technology tendencies in different energy technological areas. Innovative highlights and descriptions of preproduction energy systems and components from the past four years have been gathered from selected journals and international energy departments from G20 countries. As the field develops, readers are in...

Cost Effective Technologies and Renewable Substrates for Biosurfactants’ Production

Directory of Open Access Journals (Sweden)

Ibrahim M Banat

2014-12-01

Full Text Available Diverse types of microbial surface-active amphiphilic molecules are produced by a range of microbial communities. The extraordinary properties of biosurfactant / bioemulsifier (BS/BE as surface active products allows them to have key roles in various field of applications such as bioremediation, biodegradation, enhanced oil recovery, pharmaceutics, food processing among many others. This leads to a vast number of potential applications of these BS/BE in different industrial sectors. Despite the huge number of reports and patents describing BS and BE applications and advantages, commercialization of these compounds remain difficult, costly and to a large extent irregular. This is mainly due to the usage of chemically synthesized media for growing producing microorganism and in turn the production of preferred quality products. It is important to note that although a number of developments have taken place in the field of biosurfactant industries, large scale production remains economically challenging for many types of these products. This is mainly due to the huge monetary difference between the investment and achievable productivity from the commercial point of view. This review discusses low cost, renewable raw substrates and fermentation technology in BS/BE production processes and their role in reducing the production cost.

Progress in high-energy laser technology

International Nuclear Information System (INIS)

Miyanaga, Noriaki; Kitagawa, Yoneyoshi; Nakatsuka, Masahiro; Kanabe, Tadashi; Okuda, Isao

2005-01-01

The technological development of high-energy lasers is one of the key issues in laser fusion research. This paper reviews several technologies on the Nd:glass laser and KrF excimer laser that are being used in the current laser fusion experiments and related plasma experiments. Based on the GEKKO laser technology, a new high-energy Nd: glass laser system, which can deliver energy from 10 kJ (boad-band operation) to 20 kJ (narrow-band operation), is under construction. The key topics in KrF laser development are improved efficiency and repetitive operation, which aim at the development of a laser driven for fusion reactor. Ultra-intense-laser technology is also very important for fast ignition research. The key technology for obtaining the petawatt output with high beam quality is reviewed. Regarding the uniform laser irradiation required for high-density compression, the beam-smoothing methods on the GEKKO XII laser are reviewed. Finally, we discuss the present status of MJ-class lasers throughout the world, and summarize by presenting the feasibility of various applications of the high-energy lasers to a wide range of scientific and technological fields. (author)

Additive Manufacturing and High-Performance Computing: a Disruptive Latent Technology

Science.gov (United States)

Goodwin, Bruce

2015-03-01

This presentation will discuss the relationship between recent advances in Additive Manufacturing (AM) technology, High-Performance Computing (HPC) simulation and design capabilities, and related advances in Uncertainty Quantification (UQ), and then examines their impacts upon national and international security. The presentation surveys how AM accelerates the fabrication process, while HPC combined with UQ provides a fast track for the engineering design cycle. The combination of AM and HPC/UQ almost eliminates the engineering design and prototype iterative cycle, thereby dramatically reducing cost of production and time-to-market. These methods thereby present significant benefits for US national interests, both civilian and military, in an age of austerity. Finally, considering cyber security issues and the advent of the ``cloud,'' these disruptive, currently latent technologies may well enable proliferation and so challenge both nuclear and non-nuclear aspects of international security.

Technology, safety and costs of decommissioning reference light water reactors following postulated accidents

International Nuclear Information System (INIS)

Konzek, G.J.; Smith, R.I.

1990-12-01

The estimated costs for post-accident cleanup at the reference BWR (developed previously in NUREG/CR-2601, Technology, Safety and Costs of Decommissioning Reference Light Water Reactors Following Postulated Accidents) are updated to January 1989 dollars in this report. A simple formula for escalating post-accident cleanup costs is also presented. Accident cleanup following the most severe accident described in NUREG/CR-2601 (i.e., the Scenario 3 accident) is estimated to cost from $1.22 to 1.44 billion, in 1989 dollars, for assumed escalation rates of 4% or 8% in the years following 1989. The time to accomplish cleanup remained unchanged from the 8.3 years originally estimated. No reanalysis of current information on the technical aspects of TMI-2 cleanup has been performed. Only the cost of inflation has been evaluated since the original PNL analysis was completed. 32 refs., 12 tabs

Cost-effectiveness analysis and innovation.

Science.gov (United States)

Jena, Anupam B; Philipson, Tomas J

2008-09-01

While cost-effectiveness (CE) analysis has provided a guide to allocating often scarce resources spent on medical technologies, less emphasis has been placed on the effect of such criteria on the behavior of innovators who make health care technologies available in the first place. A better understanding of the link between innovation and cost-effectiveness analysis is particularly important given the large role of technological change in the growth in health care spending and the growing interest of explicit use of CE thresholds in leading technology adoption in several Westernized countries. We analyze CE analysis in a standard market context, and stress that a technology's cost-effectiveness is closely related to the consumer surplus it generates. Improved CE therefore often clashes with interventions to stimulate producer surplus, such as patents. We derive the inconsistency between technology adoption based on CE analysis and economic efficiency. Indeed, static efficiency, dynamic efficiency, and improved patient health may all be induced by the cost-effectiveness of the technology being at its worst level. As producer appropriation of the social surplus of an innovation is central to the dynamic efficiency that should guide CE adoption criteria, we exemplify how appropriation can be inferred from existing CE estimates. For an illustrative sample of technologies considered, we find that the median technology has an appropriation of about 15%. To the extent that such incentives are deemed either too low or too high compared to dynamically efficient levels, CE thresholds may be appropriately raised or lowered to improve dynamic efficiency.

Climbing Up the Technology Ladder? High-Technology Exports in China and Latin America

OpenAIRE

Gallagher, Kevin P.; Porzecanski, Roberto

2008-01-01

In this paper we determine the “dynamic revealed competitiveness position” (DRCP) of nations for high technology exports between 1980 and 2005. We find that the developed world has lost significant market share in high technology and that China has climbed the high technology ladder during this period. In 1980 China was ranked 99th of all nations in terms of the percentage of global exports in high technology. By 2005 China climbed to second place in the world, first place if high technology ...

State investments in high-technology job growth.

Science.gov (United States)

Leicht, Kevin T; Jenkins, J Craig

2017-07-01

Since the early 1970's state and local governments have launched an array of economic development programs designed to promote high-technology development. The question our analysis addresses is whether these programs promote long-term high-technology employment growth net of state location and agglomeration advantages. Proponents talk about an infrastructure strategy that promotes investment in public research and specialized infrastructure to attract and grow new high technology industries in specific locations, and a more decentralized entrepreneurial strategy that reinforces local agglomeration capacities by investing in new enterprises and products, promoting the development of local networks and partnerships. Our results support the entrepreneurial strategy, suggesting that state governments can accelerate high technology development by adopting market-supportive programs that complement private sector initiatives. In addition to positive direct benefits of technology deployment/transfer programs and SBIR programs, entrepreneurial programs affect change in high-technology employment in concert with existing locational and agglomeration advantages. Rural (i.e. low population density) states tend to benefit by technology development programs. Infrastructure strategy programs also facilitate high technology job growth in places where local advantages already exist. Our results suggest that critics of industrial policy are correct that high technology growth is organic and endogenous, yet state governments are able to "pick winners and losers" in ways that grow their local economy. Copyright © 2017 Elsevier Inc. All rights reserved.

Beban Biaya Telekomunikasi yang Dikeluarkan Masyarakat Pengaruh dari Adopsi Teknologi [Telecommunication Costs Incurred Expenses Society Effect of Technology Adoption

Directory of Open Access Journals (Sweden)

Sri Ariyanti

2016-07-01

Full Text Available Salah satu Rencana Pita Lebar Indonesiatahun 2014 – 2019 yaitu dapat memberikan akses bergerak  di wilayah pedesaan  menjangkau 52% pupulasi dengan data rate mencapai 1 Mbps.  Agar layanan pita lebar dapat terjangkau oleh masyarakat luas, maka harga layanan pita lebar ditargetkan paling tinggi sebesar 5% dari rata-rata pendapatan bulanan pada akhir tahun 2019.  Rencana pita lebar dengan target minimal data rate tersebut tidak akan tercapai tanpa adanya perubahan teknologi.  Teknologi yang mendukung terpenuhinya data rate tersebut antara lain teknologi 3.5G dan 4G LTE.  Dalam rangka upgrade teknologi, perlu adanya biaya yang cukup besar yang dikeluarkan oleh operator.  Biaya tersebut sangat mempengaruhi besar biaya yang akan dibebankan kepada pelanggan.  Oleh karena itu dalam penelitian ini mengkaji seberapa besar biaya yang ditanggung pelanggan seluler setelah adanya teknologi baru. Penelitian ini bertujuan untuk mengetahui apakah biaya yang dibebankan kepada masyarakat sudah sesuai dengan yang ditetapkan oleh pemerintah dalam Rencana Pita Lebar Indonesia. Teknik peneltiian ini menggunakan pendekatan data kuantitatif yang dianalisis dengan ekonometrika.  Hasil penelitian menunjukkan bahwa berdasarkan data penegeluarna telekomunikasi rumah tangga maupun data ARPU, biaya yang dibebankan kepada pelanggan sudah memenuhih persyaratan yang telah ditetapaka oleh rencana pita lebar Indonesia yaitu kurang dari 5%. *****One of the Indonesia Broadband Plan in 2014 – 2019 is that it can be provided mobile data reaching 52% rural areas with data rate up to 1 Mbps. In order to be affordable, so that maximum price is 5% of the average monthly income at the end of 2019.  That data rate cannot be achieved without upgrading the technology. The technology of 3.5G and 4G are among others technology that can support high data rate.  In order to upgrade technology, it needs a considerable cost from mobile operators, while it can influence the cost

Parametric cost models for space telescopes

Science.gov (United States)

Stahl, H. Philip; Henrichs, Todd; Dollinger, Courtnay

2017-11-01

Multivariable parametric cost models for space telescopes provide several benefits to designers and space system project managers. They identify major architectural cost drivers and allow high-level design trades. They enable cost-benefit analysis for technology development investment. And, they provide a basis for estimating total project cost. A survey of historical models found that there is no definitive space telescope cost model. In fact, published models vary greatly [1]. Thus, there is a need for parametric space telescopes cost models. An effort is underway to develop single variable [2] and multi-variable [3] parametric space telescope cost models based on the latest available data and applying rigorous analytical techniques. Specific cost estimating relationships (CERs) have been developed which show that aperture diameter is the primary cost driver for large space telescopes; technology development as a function of time reduces cost at the rate of 50% per 17 years; it costs less per square meter of collecting aperture to build a large telescope than a small telescope; and increasing mass reduces cost.

Parametric Cost Models for Space Telescopes

Science.gov (United States)

Stahl, H. Philip; Henrichs, Todd; Dollinger, Courtney

2010-01-01

Multivariable parametric cost models for space telescopes provide several benefits to designers and space system project managers. They identify major architectural cost drivers and allow high-level design trades. They enable cost-benefit analysis for technology development investment. And, they provide a basis for estimating total project cost. A survey of historical models found that there is no definitive space telescope cost model. In fact, published models vary greatly [1]. Thus, there is a need for parametric space telescopes cost models. An effort is underway to develop single variable [2] and multi-variable [3] parametric space telescope cost models based on the latest available data and applying rigorous analytical techniques. Specific cost estimating relationships (CERs) have been developed which show that aperture diameter is the primary cost driver for large space telescopes; technology development as a function of time reduces cost at the rate of 50% per 17 years; it costs less per square meter of collecting aperture to build a large telescope than a small telescope; and increasing mass reduces cost.

High-value, cost-conscious health care: concepts for clinicians to evaluate the benefits, harms, and costs of medical interventions.

Science.gov (United States)

Owens, Douglas K; Qaseem, Amir; Chou, Roger; Shekelle, Paul

2011-02-01

Health care costs in the United States are increasing unsustainably, and further efforts to control costs are inevitable and essential. Efforts to control expenditures should focus on the value, in addition to the costs, of health care interventions. Whether an intervention provides high value depends on assessing whether its health benefits justify its costs. High-cost interventions may provide good value because they are highly beneficial; conversely, low-cost interventions may have little or no value if they provide little benefit. Thus, the challenge becomes determining how to slow the rate of increase in costs while preserving high-value, high-quality care. A first step is to decrease or eliminate care that provides no benefit and may even be harmful. A second step is to provide medical interventions that provide good value: medical benefits that are commensurate with their costs. This article discusses 3 key concepts for understanding how to assess the value of health care interventions. First, assessing the benefits, harms, and costs of an intervention is essential to understand whether it provides good value. Second, assessing the cost of an intervention should include not only the cost of the intervention itself but also any downstream costs that occur because the intervention was performed. Third, the incremental cost-effectiveness ratio estimates the additional cost required to obtain additional health benefits and provides a key measure of the value of a health care intervention.

Low Cost High Performance Generator Technology Program. Volume 2. Design study

International Nuclear Information System (INIS)

1975-06-01

The systems studies directed towards up-rating the performance of an RTG using selenide thermoelectrics and a heat source with improved safety are reported. The resulting generator design, designated LCHPG, exhibits conversion efficiency of greater than 10 percent, a specific power of 3 W/lb., and a cost of $6,000/W(e). In the course of system analyses, the significant development activities required to achieve this performance by the 1980 time period are identified

Cost-effectiveness prospects of picture archiving and communication systems.

Science.gov (United States)

Hindel, R; Preger, W

1988-01-01

PAC (picture archiving and communication) systems are widely discussed and promoted as the organizational solution to digital image management in a radiology department. For approximately two decades digital imaging has increasingly been used for such diagnostic modalities as CT, DSA, MRI, DR (Digital Radiography) and others. PACS are seen as a step toward high technology integration and more efficient management. Although the acquisition of such technology is investment intensive, there are well-founded projections that prolonged operation will prove cost justified. Such justification can only partly be derived from cost reduction through PAC with respect to present department management--the major justification is preparation for future economic pressures which could make survival of a department without modern technology difficult. Especially in the United States the political climate favors 'competitive medicine' and reduced government support. Seen in this context PACS promises to speed the transition of Health Care Services into a business with tight resource management, cost accounting and marketing. The following paper analyzes cost and revenue in a typical larger Radiology Department, projects various scenarios of cost reduction by means of digital technology and concludes with cautious optimism that the investment expenses for a PACS will be justified in the near future by prudent utilization of high technology.

Levelised unit electricity cost comparison of alternate technologies for baseload generation in Ontario

Energy Technology Data Exchange (ETDEWEB)

Ayres, M.; McRae, M.; Stogran, M.

2004-08-15

This report provides a comparison of the lifetime cost of constructing, operating and decommissioning new generation suitable for supplying baseload power by early in the next decade. New baseload generation options in Ontario are nuclear, coal-fired steam turbines or combined cycle gas turbines (CCGT). Nuclear and coal-fired units are characterised by high capital costs and low operating costs. As such, they are candidates for baseload operation only. Gas-fired generation is characterised by lower capital costs and higher operating costs and thus may meet the requirements for operation as peaking and/or baseload generation. The comparison of baseload generating technologies is made by reference to the estimated levelised unit electricity cost (LUEC). The LUEC can be thought of as a 'supply cost', where the unit cost is the price needed to recover all costs over the period. It is determined by finding the price that sets the sum of all future discounted cash flows (net present value, or NPV) to zero. It can also be thought of as representing the constant real wholesale price of electricity that meets the financing cost, debt repayment, income tax and cash flow constraints associated with the construction operation and decommissioning of a generating plant. Levelised unit cost comparisons are usually made with different sets of financing assumptions. This report considers two base cases, which we describe as 'merchant' and 'public' financing. The term 'merchant plant' is used to refer to ones that are built and operated by private investors. These investors pay for their capital through debt and by raising equity, and thus pay return on equity and interest on debt throughout their lifetime. These projects include income taxes, both provincial and federal. Publicly financed projects typically are not subject to income taxes or to the same constraints on raising finance through issuing debt and equity. However, they are

Reducing the cost of administrative justice

International Nuclear Information System (INIS)

Tourtellotte, J.R.

1982-01-01

In virtually every sector of government regulation, the complaint has been lodged that the costs of administrative justice are too high. These costs in time, money, resources, and productivity can have a profound effect on the individual consumer. When applied to an energy technology such as nuclear power, costs of administrative justice can transcent time and money to have even more profound and pervasive soeietal effects. Societal costs can be expressed in terms of their impact on important national concerns, that is, the standard of living, technological superiority, and the national energy equation. Some views are presented on the interests involved in the regulation of nuclear power and what can be done to bring those interests into better balance so as to reduce the cost of administrative justice

New Technological Options to Manage High Level Waste

International Nuclear Information System (INIS)

Gonzalez Romero, E. M.

2007-01-01

Nuclear energy renaissance and its expansion in time and space has renewed the need for minimization technologies applicable to nuclear wastes. The minimization technologies include new power reactor concepts, Generation IV, and dedicated technologies like Partitioning and Transmutation of the actinides contained in the spent fuel. These technologies apply the principle of classification and recycling to the spent fuel to transform what at present is an environmental hazard into an energy source. the waste minimization technologies are also relevant for countries planning the reduction or phase-out of nuclear energy, as they will allow minimizing the size and number of the final waste repositories. Present estimations indicate that reductions as large as a factor 100 in the amount (radiotoxicity) of long lived nuclear waste are feasibly, with a modest increase on the final electricity cost. (Author)

The Social Costs of Electricity Generation—Categorising Different Types of Costs and Evaluating Their Respective Relevance

Directory of Open Access Journals (Sweden)

Sascha Samadi

2017-03-01

Full Text Available Various electricity generation technologies using different primary energy sources are available. Many published studies compare the costs of these technologies. However, most of those studies only consider plant-level costs and do not fully take into account additional costs that societies may face in using these technologies. This article reviews the literature on the costs of electricity generation technologies, aiming to determine which types of costs are relevant from a societal point of view when comparing generation technologies. The paper categorises the relevant types of costs, differentiating between plant-level, system and external costs as the main categories. It discusses the relevance of each type of cost for each generation technology. The findings suggest that several low-carbon electricity generation technologies exhibit lower social costs per kWh than the currently dominant technologies using fossil fuels. More generally, the findings emphasise the importance of taking not only plant-level costs, but also system and external costs, into account when comparing electricity generation technologies from a societal point of view. The article intends to inform both policymakers and energy system modellers, the latter who may strive to include all relevant types of costs in their models.

New Sunshine Program for fiscal 2000. Development of photovoltaic system commercialization technology - Development of thin-film solar cell manufacturing technology - Development of low-cost/large area module manufacturing technology (Development of novel amorphous solar cell module manufacturing technology); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Tei cost dai menseki mojuru seizo gijutsu kaihatsu (Shingata amorufasu taiyo denchi mojuru no seizo gijutsu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was conducted for the development of amorphous solar cell modules for power generation, high in performance and low in production cost. In the effort to develop high-performance solar cells, optimum device designs including an advanced light confinement structure or the like were studied, and a 25% reduction in the total power generation layer thickness and a 7% increase in efficiency in power generation were consistently achieved in an a-Si/a-SiGe solar cell. In the effort to develop low-cost process technologies, as the result of studies involving the optimization of high-speed film fabrication requirements such as hydrogen dilution and a high-speed/high-precision patterning method and the like, an initial conversion efficiency of 11.2% was attained, which was the world high for a 90 cm times 90 cm-large a-Si/a-SiGe solar cell. This being equivalent to a post-stabilization efficiency of 10%, the fiscal 2000 target was achieved. A solar cell module production cost assessment was performed based on the result, and a module cost of 133 yen/W (in case of 100 MW/year production) was realized, which again meant the achievement of the fiscal 2000 target. (NEDO)

Cost, affordability and cost-effectiveness of strategies to control tuberculosis in countries with high HIV prevalence

Directory of Open Access Journals (Sweden)

Williams Brian G

2005-12-01

Full Text Available Abstract Background The HIV epidemic has caused a dramatic increase in tuberculosis (TB in East and southern Africa. Several strategies have the potential to reduce the burden of TB in high HIV prevalence settings, and cost and cost-effectiveness analyses can help to prioritize them when budget constraints exist. However, published cost and cost-effectiveness studies are limited. Methods Our objective was to compare the cost, affordability and cost-effectiveness of seven strategies for reducing the burden of TB in countries with high HIV prevalence. A compartmental difference equation model of TB and HIV and recent cost data were used to assess the costs (year 2003 US$ prices and effects (TB cases averted, deaths averted, DALYs gained of these strategies in Kenya during the period 2004–2023. Results The three lowest cost and most cost-effective strategies were improving TB cure rates, improving TB case detection rates, and improving both together. The incremental cost of combined improvements to case detection and cure was below US$15 million per year (7.5% of year 2000 government health expenditure; the mean cost per DALY gained of these three strategies ranged from US$18 to US$34. Antiretroviral therapy (ART had the highest incremental costs, which by 2007 could be as large as total government health expenditures in year 2000. ART could also gain more DALYs than the other strategies, at a cost per DALY gained of around US$260 to US$530. Both the costs and effects of treatment for latent tuberculosis infection (TLTI for HIV+ individuals were low; the cost per DALY gained ranged from about US$85 to US$370. Averting one HIV infection for less than US$250 would be as cost-effective as improving TB case detection and cure rates to WHO target levels. Conclusion To reduce the burden of TB in high HIV prevalence settings, the immediate goal should be to increase TB case detection rates and, to the extent possible, improve TB cure rates, preferably

Multi-Site Project Management A Program for Reducing the Cost of Technology Deployment at Department of Energy Sites

International Nuclear Information System (INIS)

Davis, N.R.; Selden, E.R.; Little, D.B.; Coleman, M.C.; Bennett, J.T.

2009-01-01

Retrieval and processing of High Level Waste (HLW) stored in Department of Energy (DOE) waste tanks is performed to support closure of the tanks as required by site specific regulatory agreements. Currently, there are four sites in the DOE Complex that have HLW tanks and must process and disposition HLW. As such, there is an opportunity to achieve an economy of scale and reduce duplication of efforts. Two or more sites typically have similar technology development and deployment needs. Technology development is already executed at the national level. As the technology is matured, the next step is to commission a design/build project. Typically each site performs this separately due to differences in waste type, tank design, site specific considerations such as proximity to the water table or to the site boundary. The focus of the individual sites tends to be on the differences between sites versus on the similarities thus there is an opportunity to minimize the cost for similar deployments. A team of engineers and project management professionals from the Savannah River Site has evaluated technology needs at the four HLW sites and determined that there is an economy of scale that can be achieved by specific technology deployments in the area of waste retrieval, waste pretreatment and waste disposition. As an example, the Waste on Wheels tank retrieval system (presented in the 2006 Waste Management Symposium) was designed and fabricated in portable modules that could be installed in HLW tanks at Hanford, Savannah River or Idaho. This same concept could be used for modular in-tank cesium removal process and equipment, tank cleaning mechanical equipment, and chemical tank cleaning process and equipment. The purpose of this paper is to present a multi-site project management approach that will reduce deployment costs and be consistent with DOE Order 413.3 project management principles. The approach will describe how projects can be managed by a lead site with

Wind Integration Cost and Cost-Causation: Preprint

Energy Technology Data Exchange (ETDEWEB)

Milligan, M.; Kirby, B.; Holttinen, H.; Kiviluoma, J.; Estanqueiro, A.; Martin-Martinez, S.; Gomez-Lazaro, E.; Peneda, I.; Smith, C.

2013-10-01

The question of wind integration cost has received much attention in the past several years. The methodological challenges to calculating integration costs are discussed in this paper. There are other sources of integration cost unrelated to wind energy. A performance-based approach would be technology neutral, and would provide price signals for all technology types. However, it is difficult to correctly formulate such an approach. Determining what is and is not an integration cost is challenging. Another problem is the allocation of system costs to one source. Because of significant nonlinearities, this can prove to be impossible to determine in an accurate and objective way.

Evaluation of cost reduction method for manufacturing ODS ferritic claddings

International Nuclear Information System (INIS)

Fujiwara, Masayuki; Mizuta, Shunji; Ukai, Shigeharu

2000-04-01

For evaluating the fast reactor system technology, it is important to evaluate the practical feasibility of ODS ferritic claddings, which is the most promising materials to attain the goal of high coolant temperature and more than 150 GWd/t. Based on the results of their technology development, mass production process with highly economically benefit as well as manufacturing cost estimation of ODS ferritic claddings were preliminarily conducted. From the view point of future utility scale, the cost for manufacturing mother tubes has a dominant factor in the total manufacturing cost. The method to reduce the cost of mother tube manufacturing was also preliminarily investigated. (author)

WHAT DRIVES HIGH COST OF FINANCE IN MOLDOVA?

Directory of Open Access Journals (Sweden)

Alexandru Stratan

2012-03-01

Full Text Available Why there are high costs to finance in Republic of Moldova? Is it a problem for business environment?These are the questions discussed in this paper. Following the well know Growth Diagnostics approach byHausmann, Rodrik and Velasco, authors assess the barriers and impediments to access to finance in Republic ofMoldova. Guided by international and national statistics we found evidence of poor intermediation, poorinstitutions, high level of inflation, and high collateral as major causes of high cost of financial resources inRepublic of Moldova. At the end of the study authors give policy recommendations identifying other related fieldsto be addressed.

Energy and cost savings results for advanced technology systems from the Cogeneration Technology Alternatives Study /CTAS/

Science.gov (United States)

Sagerman, G. D.; Barna, G. J.; Burns, R. K.

1979-01-01

The Cogeneration Technology Alternatives Study (CTAS), a program undertaken to identify the most attractive advanced energy conversion systems for industrial cogeneration applications in the 1985-2000 time period, is described, and preliminary results are presented. Two cogeneration options are included in the analysis: a topping application, in which fuel is input to the energy conversion system which generates electricity and waste heat from the conversion system is used to provide heat to the process, and a bottoming application, in which fuel is burned to provide high temperature process heat and waste heat from the process is used as thermal input to the energy conversion system which generates energy. Steam turbines, open and closed cycle gas turbines, combined cycles, diesel engines, Stirling engines, phosphoric acid and molten carbonate fuel cells and thermionics are examined. Expected plant level energy savings, annual energy cost savings, and other results of the economic analysis are given, and the sensitivity of these results to the assumptions concerning fuel prices, price of purchased electricity and the potential effects of regional energy use characteristics is discussed.

Effect of scale and quantity on the cost and performance of energy technologies: a literature review

International Nuclear Information System (INIS)

Hill, D.

1983-11-01

Traditionally, a six-tenths power law stated that cost increased by only half with a doubling of plant size, reducing cost per unit of capacity to 75%. Problems during construction in the past two decades have largely nullified the expected savings. Thermal efficiency improves with size in both coal and nuclear plants, but plant availability declines. These trends suggest that an optimal size for nuclear plants may be somewhat less than 1000 MW(e). Judged by a study of the cost of electricity generated during the 1970s, however, operational savings substantially restored economies of scale to nuclear plants but not to coal plants. The alternative to building larger plants is to build more small plants. In field construction, a second plant at the same site costs about 90% of the first, and a doubling of the number of plants built by an architect-engineer appears to reduce average cost to about 93%. In a variety of manufacturing industries, the learning curve is steeper. In the few cases where learning curves are mentioned in manufacturing studies of new energy technologies, however, a reduction in cost to only about 90% with a doubling of quantity is assumed. Most of the cost of new energy technologies such as photovoltaic arrays and fuel cells will be due to conventional equipment, structure, and manufacturing methods. It should therefore be possible to estimate size-quantity cost tradeoffs with some confidence to help establish optimal plant or module sizes

Ablation - breakthrough technology to reduce uranium mining cost and increase resources

International Nuclear Information System (INIS)

Scriven, D.

2014-01-01

Ablation Technologies, LLC has developed and patented a revolutionary mining technology termed “ablation”. Ablation is a process using only mechanical forces to upgrade sandstone uranium ores. Uranium bearing sandstone orebodies are formed from a uranium enriched solution flowing through an aquifer until it reached some type of a “red/ox” zone forcing the uranium and other heavy metals to come out of solution. The precipitate forms a thin coating on the sand grains and fills the interstitial space between the sand grains but does no penetrate the sand grains. The ablation process knocks the precipitate off the sand grains using the forces of abrasion, elastic compression and rebounding, much like a mud coated tennis ball will sheds the mud when bounced off the ground, and to some extent, sonic waves. This produces a product which collectively is exactly the same as the ore going in but with all the individual components separated. This allows for disgressionary separation, the most important of which is screening. The uranium and heavy metals report to the finer fractions of the material, typically less than 250 mesh. The larger fractions contain less than five percent of the uranium but 90 to 95 percent of the mass. The advantages of making an enriched ore are numerous: • Reduce haulage costs from 90 to 95 percent. • Reduce milling costs by reducing material handling costs, acid consumption and tailings disposal costs. • In addition to reducing overall mining and milling costs, the overall recovery of the recourse is increased because the ablation process is so inexpensive, if the material has to be mined it will be ablated and screened. This basically means ore control is significantly reduced, cutoff grade goes to practically zero and overall resource recovery is significantly increased. • Environmentally, the two major advantages are reduced tailings requirements at the mill site and cleaner waste dumps at the mine site. This paper will show

Additive Manufacturing and Casting Technology Comparison: Mechanical Properties, Productivity and Cost Benchmark

Science.gov (United States)

Vevers, A.; Kromanis, A.; Gerins, E.; Ozolins, J.

2018-04-01

The casting technology is one of the oldest production technologies in the world but in the recent years metal additive manufacturing also known as metal 3D printing has been evolving with huge steps. Both technologies have capabilities to produce parts with internal holes and at first glance surface roughness is similar for both technologies, which means that for precise dimensions parts have to be machined in places where precise fit is necessary. Benchmark tests have been made to find out if parts which are produced with metal additive manufacturing can be used to replace parts which are produced with casting technology. Most of the comparative tests have been made with GJS-400-15 grade which is one of the most popular cast iron grades. To compare mechanical properties samples have been produced using additive manufacturing and tested for tensile strength, hardness, surface roughness and microstructure and then the results have been compared with the samples produced with casting technology. In addition, both technologies have been compared in terms of the production time and production costs to see if additive manufacturing is competitive with the casting technology. The original paper has been written in the Latvian language as part of the Master Thesis within the framework of the production technology study programme at Riga Technical University.

A high resolution melting (HRM) technology-based assay for cost-efficient clinical detection and genotyping of herpes simplex virus (HSV)-1 and HSV-2.

Science.gov (United States)

Lieveld, M; Carregosa, A; Benoy, I; Redzic, N; Berth, M; Vanden Broeck, D

2017-10-01

Genital herpes can be caused by two very similar viruses, herpes simplex virus (HSV)-1 or HSV-2. These two HSV types cannot be distinguished clinically, but genotyping is recommended in the first-episodes of genital herpes to guide counselling and management. Quantitative polymerase chain reaction (qPCR) is the preferred diagnostic method for HSV typing. However, commercial qPCR methods use expensive fluorescent labeled probes for detection. Furthermore, most low-cost methods are not able to differentiate between HSV-1 and -2. The aim of this study was to develop a high resolution melting (HRM) technology-based assay for sensitive HSV-1 and HSV-2 detection and genotyping. Using a panel of 46 clinical specimens, the performance of the HRM assay was compared to two commercial HSV tests: the HRM assay detected HSV in all 23 positive samples, with no false positive results (100% concordance with HSV I/II Real-TM assay). Additionally, the HRM assay correctly genotyped both HSV types in a subset of these clinical samples, as determined by the Realstar HSV PCR Kit. The HSV HRM assay provides a cost-effective alternative method to conventional more expensive assays and can be used in routine clinical specimens, in cases where it is particularly necessary to detect and distinguish HSV-1 from -2. Copyright © 2017 Elsevier B.V. All rights reserved.

High fidelity medical simulation in the difficult environment of a helicopter: feasibility, self-efficacy and cost

Directory of Open Access Journals (Sweden)

Holland Carolyn

2006-10-01

environments, including ground transport and for running codes in hospital. Conclusion It is feasible to provide a high fidelity medical simulation experience in the difficult environment of the air ambulance helicopter, although further experience is necessary to eliminate practical problems. Simulation improves recognition of the challenges present and provides an important opportunity for training in challenging environments. However, use of simulation technology is expensive both in terms of monetary outlay and of personnel involvement. The benefits of this technology must be weighed against the cost for each institution.

Ownership, competition, and the adoption of new technologies and cost-saving practices in a fixed-price environment.

Science.gov (United States)

Hirth, R A; Chernew, M E; Orzol, S M

2000-01-01

Advances in medical technology have been implicated as the primary cause of rising health care expenditures. It is not yet known whether the increasing prevalence of managed care mechanisms, particularly capitation, will change substantially incentives for acquiring and using cost-increasing innovations. We examined the decisions of dialysis units (a set of providers that has faced capitation and real decreases in payment for several decades) with respect to use of cost-increasing technologies that enhance quality of care, cost-cutting practices that reduce quality of care, and amenities desired by patients that are unrelated to quality of care. We found that the dialysis payment system does not appear to have blocked access to a number of new, quality-enhancing technologies that were developed in the 1980s. However, facilities made adjustments along other valuable margins to facilitate adoption of these technologies; use of new technologies varied with numerous facility, regulatory, and case-mix characteristics including ownership, chain membership, size, market competition, and certificate of need programs. Interestingly, the trade-offs made by for-profit and nonprofit facilities when faced with fixed prices appeared quite different. For-profits tended to deliver lower technical quality of care but more amenities, while nonprofits favored technical quality of care over amenities. Our findings may have implications for the response of other types of health care providers to capitation and increasing economic constraints.

A cost-benefit analysis of alternatively fueled buses with special considerations for V2G technology

International Nuclear Information System (INIS)

Shirazi, Yosef; Carr, Edward; Knapp, Lauren

2015-01-01

Motivated by climate, health and economic considerations, alternatively-fueled bus fleets have emerged worldwide. Two popular alternatives are compressed natural gas (CNG) and electric vehicles. The latter provides the opportunity to generate revenue through vehicle-to-grid (V2G) services if properly equipped. This analysis conducts a robust accounting of the costs of diesel, CNG and battery-electric powertrains for school buses. Both marginal and fleet-wide scenarios are explored. Results indicate that the marginal addition of neither a small CNG nor a small V2G-enabled electric bus is cost effective at current prices. Contrary to previous findings, a small V2G-enabled electric bus increases net present costs by $7,200/seat relative to diesel for a Philadelphia, PA school district. A small CNG bus increases costs by $1,200/seat relative to diesel. This analysis is the first to quantify and include the economic implications of cold temperature extremes on electric vehicle battery operations, and the lower V2G revenues that result. Additional costs and limitations imposed by electric vehicles performing V2G are frequently overlooked in the literature and are explored here. If a variety of technical, legal, and economic challenges are overcome, a future eBus may be economical. - Highlights: • We present a robust cost-benefit analysis of various bus technologies. • Diesel is a low-cost technology at current prices. • CNG represents slightly higher costs on a marginal bus basis. • V2G-enabled electric buses are not cost-effective at current prices. • We identify frequently overlooked costs and challenges to V2G implementation.

SmallSats, Iodine Propulsion Technology, Applications to Low-Cost Lunar Missions, and the Iodine Satellite (iSAT) Project

Science.gov (United States)

Dankanich, John W.

2014-01-01

Closing Remarks: ?(1) SmallSats hold significant potential for future low cost high value missions; (2) Propulsion remains a key limiting capability for SmallSats that Iodine can address: High ISP * Density for volume constrained spacecraft; Indefinite quiescence, unpressurized and non-hazardous as a secondary payload; (3) Iodine enables MicroSat and SmallSat maneuverability: Enables transfer into high value orbits, constellation deployment and deorbit; (4) Iodine may enable a new class of planetary and exploration class missions: Enables GTO launched secondary spacecraft to transit to the moon, asteroids, and other interplanetary destinations for approximately 150 million dollars full life cycle cost including the launch; (5) ESPA based OTVs are also volume constrained and a shift from xenon to iodine can significantly increase the transfer vehicle change in volume capability including transfers from GTO to a range of Lunar Orbits; (6) The iSAT project is a fast pace high value iodine Hall technology demonstration mission: Partnership with NASA GRC and NASA MSFC with industry partner - Busek; (7) The iSAT mission is an approved project with PDR in November of 2014 and is targeting a flight opportunity in FY17.

Medicaid care management: description of high-cost addictions treatment clients.

Science.gov (United States)

Neighbors, Charles J; Sun, Yi; Yerneni, Rajeev; Tesiny, Ed; Burke, Constance; Bardsley, Leland; McDonald, Rebecca; Morgenstern, Jon

2013-09-01

High utilizers of alcohol and other drug treatment (AODTx) services are a priority for healthcare cost control. We examine characteristics of Medicaid-funded AODTx clients, comparing three groups: individuals cost clients in the top decile of AODTx expenditures (HC; n=5,718); and 1760 enrollees in a chronic care management (CM) program for HC clients implemented in 22 counties in New York State. Medicaid and state AODTx registry databases were combined to draw demographic, clinical, social needs and treatment history data. HC clients accounted for 49% of AODTx costs funded by Medicaid. As expected, HC clients had significant social welfare needs, comorbid medical and psychiatric conditions, and use of inpatient services. The CM program was successful in enrolling some high-needs, high-cost clients but faced barriers to reaching the most costly and disengaged individuals. Copyright © 2013 Elsevier Inc. All rights reserved.

Cost/benefit analysis for selected waste minimization technologies at TA-55

International Nuclear Information System (INIS)

Boerigter, S.T.

1996-01-01

The TA-55 plutonium facility at LANL is one of the remaining plutonium-handling facilities in the United States with significant operational capability. In recent years a great deal of attention has been focused on the waste streams generated by this facility. Costs of properly treating these streams have risen significantly. This paper discusses the characterization of several proposed radioactive waste minimization technologies as a function of Return on Investment (ROI). In particular, the DOE Environmental Management program has identified a specific funding channel for such technology development activities, but this funding channel requires a restrictive definition of ROI. Here, a simple extension to the required ROI equation is used to capture the lifecycle ROI due to offsets in future capital charges resulting from present spending

Technology and costs for decommissioning Swedish nuclear power plants; Teknik och kostnader foer rivning av svenska kaernkraftverk

Energy Technology Data Exchange (ETDEWEB)

Hedin, Gunnar; Gustavsson, Boerje [Westinghouse Electric Sweden AB, Vaesteraas (Sweden); Carlsson, Jan [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

2004-06-01

SKB has already performed three studies on available technology and approximate costs for decommissioning Swedish NPPs (years 1986, 1994 and 2000). The present report is an update of the year 2000 report with emphasis on areas that have been studied since the publication of that report. The report also gives a review of the technologies that have been chosen for decommissioning the Swedish reactors. The cost-estimation has also been updated and indexed to the present monetary situation. Areas in need for further studies are pointed in the report.

Life Science Research in Outer Space: New Platform Technologies for Low-Cost, Autonomous Small Satellite Missions

Science.gov (United States)

Ricco, Antonio J.; Parra, Macarena P.; Niesel, David; McGinnis, Michael; Ehrenfreund, Pascale; Nicholson, Wayne; Mancinelli, Rocco; Piccini, Matthew E.; Beasley, Christopher C.; Timucin, Linda R.;

Survey of LWR environmental control technology performance and cost

International Nuclear Information System (INIS)

Heeb, C.M.; Aaberg, R.L.; Cole, B.M.; Engel, R.L.; Kennedy, W.E. Jr.; Lewallen, M.A.

1980-03-01

This study attempts to establish a ranking for species that are routinely released to the environment for a projected nuclear power growth scenario. Unlike comparisons made to existing standards, which are subject to frequent revision, the ranking of releases can be used to form a more logical basis for identifying the areas where further development of control technology could be required. This report describes projections of releases for several fuel cycle scenarios, identifies areas where alternative control technologies may be implemented, and discusses the available alternative control technologies. The release factors were used in a computer code system called ENFORM, which calculates the annual release of any species from any part of the LWR nuclear fuel cycle given a projection of installed nuclear generation capacity. This survey of fuel cycle releases was performed for three reprocessing scenarios (stowaway, reprocessing without recycle of Pu and reprocessing with full recycle of U and Pu) for a 100-year period beginning in 1977. The radioactivity releases were ranked on the basis of a relative ranking factor. The relative ranking factor is based on the 100-year summation of the 50-year population dose commitment from an annual release of radioactive effluents. The nonradioactive releases were ranked on the basis of dilution factor. The twenty highest ranking radioactive releases were identified and each of these was analyzed in terms of the basis for calculating the release and a description of the currently employed control method. Alternative control technology is then discussed, along with the available capital and operating cost figures for alternative control methods

Open-source digital technologies for low-cost monitoring of historical constructions

OpenAIRE

Basto, Camilo; Pelà, Luca; Chacón Flores, Rolando Antonio

2017-01-01

This paper shows new possibilities of using novel, open-source, low-cost platforms for the structural health monitoring of heritage structures. The objective of the study is to present an assessment of increasingly available open-source digital modeling and fabrication technologies in order to identify the suitable counterparts of the typical components of a continuous static monitoring system for a historical construction. The results of the research include a simple case-study, which is pre...

Estimating Total Program Cost of a Long-Term, High-Technology, High-Risk Project with Task Durations and Costs That May Increase Over Time

National Research Council Canada - National Science Library

Brown, Gerald G; Grose, Roger T; Koyak, Robert A

2006-01-01

.... Each task suffers some risk of delay and changed cost. Ignoring budget constraints, we use Monte Carlo simulation of the duration of each task in the project to infer the probability distribution of the project completion time...

How do high cost-sharing policies for physician care affect total care costs among people with chronic disease?

Science.gov (United States)

Xin, Haichang; Harman, Jeffrey S; Yang, Zhou

2014-01-01

This study examines whether high cost-sharing in physician care is associated with a differential impact on total care costs by health status. Total care includes physician care, emergency room (ER) visits and inpatient care. Since high cost-sharing policies can reduce needed care as well as unneeded care use, it raises the concern whether these policies are a good strategy for controlling costs among chronically ill patients. This study used the 2007 Medical Expenditure Panel Survey data with a cross-sectional study design. Difference in difference (DID), instrumental variable technique, two-part model, and bootstrap technique were employed to analyze cost data. Chronically ill individuals' probability of reducing any overall care costs was significantly less than healthier individuals (beta = 2.18, p = 0.04), while the integrated DID estimator from split results indicated that going from low cost-sharing to high cost-sharing significantly reduced costs by $12,853.23 more for sick people than for healthy people (95% CI: -$17,582.86, -$8,123.60). This greater cost reduction in total care among sick people likely resulted from greater cost reduction in physician care, and may have come at the expense of jeopardizing health outcomes by depriving patients of needed care. Thus, these policies would be inappropriate in the short run, and unlikely in the long run to control health plans costs among chronically ill individuals. A generous benefit design with low cost-sharing policies in physician care or primary care is recommended for both health plans and chronically ill individuals, to save costs and protect these enrollees' health status.

Assessing the costs of municipal solid waste treatment technologies in developing Asian countries.

Science.gov (United States)

Aleluia, João; Ferrão, Paulo

2017-11-01

The management of municipal solid waste (MSW) is one of the main costs incurred by local authorities in developing countries. According to some estimates, these costs can account for up to 50% of city government budgets. It is therefore of importance that policymakers, urban planners and practitioners have an adequate understanding of what these costs consist of, from collection to final waste disposal. This article focuses on a specific stage of the MSW value chain, the treatment of waste, and it aims to identify cost patterns associated with the implementation and operation of waste treatment approaches in developing Asian countries. An analysis of the capital (CAPEX) and operational expenditures (OPEX) of a number of facilities located in countries of the region was conducted based on a database gathering nearly 100 projects and which served as basis for assessing four technology categories: composting, anaerobic digestion (AD), thermal treatment, and the production of refuse-derived fuel (RDF). Among these, it was found that the least costly to invest, asa function of the capacity to process waste, are composting facilities, with an average CAPEX per ton of 21,493 USD 2015 /ton. Conversely, at the upper end featured incineration plants, with an average CAPEX of 81,880 USD 2015 /ton, with this treatment approach ranking by and large as the most capital intensive of the four categories assessed. OPEX figures of the plants, normalized and analyzed in the form of OPEX/ton, were also found to be higher for incineration than for biological treatment methods, although on this component differences amongst the technology groups were less pronounced than those observed for CAPEX. While the results indicated the existence of distinct cost implications for available treatment approaches in the developing Asian context, the analysis also underscored the importance of understanding the local context asa means to properly identify the cost structure of each specific plant

Supporting frail older people and their family carers at home using information and communication technology: cost analysis.

Science.gov (United States)

Magnusson, Lennart; Hanson, Elizabeth

2005-09-01

This paper describes a cost analysis of a home-based support service for frail older people and their family carers in two municipalities in West Sweden and using information and communication technology. A key challenge facing nurse managers across Europe is an increasingly aged population, combined with reduced numbers of young adults of working age. New solutions are needed to provide quality, cost-effective community care services to frail older people and their family carers. A case study methodology involving five families was used, and included a detailed cost description of the technology-based service compared with usual services. Cost data were collected in June 2002. This work formed part of a larger project exploring the impact of a technology-based service known as, Assisting Carers using Telematics Interventions to meet Older Persons' Needs (ACTION). In addition to cost data, information was gathered on the quality of life of frail older people and their family carers, and the job satisfaction and work methods of nurses and other practitioners based in the community. The cost analysis comprised a description of the family and their caring situation, the perceived benefits of the telematic based support service and an assessment of its impact on the use of other care services. These analyses were carried out with the help of needs assessors who were known to the families, and nurses working in the ACTION call centre. All results were validated by the five participating families. Cost savings were achieved in all cases, and the benefits to older people and their carers were also considerable. As a result of the cost analysis and overall evaluation data, ACTION has been implemented as a mainstream service in the municipalities involved. Researchers, nurses, other practitioners and community care managers can work together with frail older people and their family carers to develop quality, cost-effective support services that reduce demands on staff

High temperature vapors science and technology

CERN Document Server

Hastie, John

2012-01-01

High Temperature Vapors: Science and Technology focuses on the relationship of the basic science of high-temperature vapors to some areas of discernible practical importance in modern science and technology. The major high-temperature problem areas selected for discussion include chemical vapor transport and deposition; the vapor phase aspects of corrosion, combustion, and energy systems; and extraterrestrial high-temperature species. This book is comprised of seven chapters and begins with an introduction to the nature of the high-temperature vapor state, the scope and literature of high-temp

Review of CMOS Integrated Circuit Technologies for High-Speed Photo-Detection.

Science.gov (United States)

Jeong, Gyu-Seob; Bae, Woorham; Jeong, Deog-Kyoon

2017-08-25

The bandwidth requirement of wireline communications has increased exponentially because of the ever-increasing demand for data centers and high-performance computing systems. However, it becomes difficult to satisfy the requirement with legacy electrical links which suffer from frequency-dependent losses due to skin effects, dielectric losses, channel reflections, and crosstalk, resulting in a severe bandwidth limitation. In order to overcome this challenge, it is necessary to introduce optical communication technology, which has been mainly used for long-reach communications, such as long-haul networks and metropolitan area networks, to the medium- and short-reach communication systems. However, there still remain important issues to be resolved to facilitate the adoption of the optical technologies. The most critical challenges are the energy efficiency and the cost competitiveness as compared to the legacy copper-based electrical communications. One possible solution is silicon photonics which has long been investigated by a number of research groups. Despite inherent incompatibility of silicon with the photonic world, silicon photonics is promising and is the only solution that can leverage the mature complementary metal-oxide-semiconductor (CMOS) technologies. Silicon photonics can be utilized in not only wireline communications but also countless sensor applications. This paper introduces a brief review of silicon photonics first and subsequently describes the history, overview, and categorization of the CMOS IC technology for high-speed photo-detection without enumerating the complex circuital expressions and terminologies.

High technology revisited: definition and position

NARCIS (Netherlands)

Steenhuis, H.J.; de Bruijn, E.J.

2006-01-01

This paper proposes a new approach to defining high technology by distinguishing two different aspects. First, complexity, which is a more or less a `static' view on high technology and is applied to both the final product as well as the production process. Second, the newness, relates to a

Electrochemistry-based approaches to low cost, high sensitivity, automated, multiplexed protein immunoassays for cancer diagnostics.

Science.gov (United States)

Dixit, Chandra K; Kadimisetty, Karteek; Otieno, Brunah A; Tang, Chi; Malla, Spundana; Krause, Colleen E; Rusling, James F

2016-01-21

Early detection and reliable diagnostics are keys to effectively design cancer therapies with better prognoses. The simultaneous detection of panels of biomarker proteins holds great promise as a general tool for reliable cancer diagnostics. A major challenge in designing such a panel is to decide upon a coherent group of biomarkers which have higher specificity for a given type of cancer. The second big challenge is to develop test devices to measure these biomarkers quantitatively with high sensitivity and specificity, such that there are no interferences from the complex serum or tissue matrices. Lastly, integrating all these tests into a technology that does not require exclusive training to operate, and can be used at point-of-care (POC) is another potential bottleneck in futuristic cancer diagnostics. In this article, we review electrochemistry-based tools and technologies developed and/or used in our laboratories to construct low-cost microfluidic protein arrays for the highly sensitive detection of a panel of cancer-specific biomarkers with high specificity which at the same time has the potential to be translated into POC applications.

Computer programs for capital cost estimation, lifetime economic performance simulation, and computation of cost indexes for laser fusion and other advanced technology facilities

International Nuclear Information System (INIS)

Pendergrass, J.H.

1978-01-01

Three FORTRAN programs, CAPITAL, VENTURE, and INDEXER, have been developed to automate computations used in assessing the economic viability of proposed or conceptual laser fusion and other advanced-technology facilities, as well as conventional projects. The types of calculations performed by these programs are, respectively, capital cost estimation, lifetime economic performance simulation, and computation of cost indexes. The codes permit these three topics to be addressed with considerable sophistication commensurate with user requirements and available data

Life cycle cost analysis of alternative vehicles and fuels in Thailand

International Nuclear Information System (INIS)

Goedecke, Martin; Therdthianwong, Supaporn; Gheewala, Shabbir H.

2007-01-01

High crude oil prices and pollution problems have drawn attention to alternative vehicle technologies and fuels for the transportation sector. The question is: What are the benefits/costs of these technologies for society? To answer this question in a quantitative way, a web-based model (http://vehiclesandfuels.memebot.com) has been developed to calculate the societal life cycle costs, the consumer life cycle costs and the tax for different vehicle technologies. By comparing these costs it is possible to draw conclusions about the social benefit and the related tax structure. The model should help to guide decisions toward optimality, which refers to maximum social benefit. The model was applied to the case of Thailand. The life cycle cost of 13 different alternative vehicle technologies in Thailand have been calculated and the tax structure analyzed

High End Computing Technologies for Earth Science Applications: Trends, Challenges, and Innovations

Science.gov (United States)

Parks, John (Technical Monitor); Biswas, Rupak; Yan, Jerry C.; Brooks, Walter F.; Sterling, Thomas L.

2003-01-01

Earth science applications of the future will stress the capabilities of even the highest performance supercomputers in the areas of raw compute power, mass storage management, and software environments. These NASA mission critical problems demand usable multi-petaflops and exabyte-scale systems to fully realize their science goals. With an exciting vision of the technologies needed, NASA has established a comprehensive program of advanced research in computer architecture, software tools, and device technology to ensure that, in partnership with US industry, it can meet these demanding requirements with reliable, cost effective, and usable ultra-scale systems. NASA will exploit, explore, and influence emerging high end computing architectures and technologies to accelerate the next generation of engineering, operations, and discovery processes for NASA Enterprises. This article captures this vision and describes the concepts, accomplishments, and the potential payoff of the key thrusts that will help meet the computational challenges in Earth science applications.

THE APPLICATION AND DEVELOPMENT OF APPROPRIATE TOOLS AND TECHNOLOGIES FOR COST-EFFECTIVE CARBON SEQUESTRATION

Energy Technology Data Exchange (ETDEWEB)

Bill Stanley; Sandra Brown; Ellen Hawes; Zoe Kant; Miguel Calmon; Gilberto Tiepolo

2002-09-01

The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research projects is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas impacts. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: advanced videography testing; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool.

Cost function estimates, scale economies and technological progress in the Turkish electricity generation sector

International Nuclear Information System (INIS)

Ali Akkemik, K.

2009-01-01

Turkish electricity sector has undergone significant institutional changes since 1984. The recent developments since 2001 including the setting up of a regulatory agency to undertake the regulation of the sector and increasing participation of private investors in the field of electricity generation are of special interest. This paper estimates cost functions and investigates the degree of scale economies, overinvestment, and technological progress in the Turkish electricity generation sector for the period 1984-2006 using long-run and short-run translog cost functions. Estimations were done for six groups of firms, public and private. The results indicate existence of scale economies throughout the period of analysis, hence declining long-run average costs. The paper finds empirical support for the Averch-Johnson effect until 2001, i.e., firms overinvested in an environment where there are excess returns to capital. But this effect was reduced largely after 2002. Technological progress deteriorated slightly from 1984-1993 to 1994-2001 but improved after 2002. Overall, the paper found that regulation of the market under the newly established regulating agency after 2002 was effective and there are potential gains from such regulation. (author)

Limiting technologies for particle beams and high energy physics

International Nuclear Information System (INIS)

Panofsky, W.K.H.

1985-07-01

Since 1930 the energy of accelerators had grown by an order of magnitude roughly every 7 years. Like all exponential growths, be they human population, the size of computers, or anything else, this eventually will have to come to an end. When will this happen to the growth of the energy of particle accelerators and colliders. Fortunately, as the energy of accelerators has grown the cost per unit energy has decreased almost as fast as has the increase in energy. The result is that while the energy has increased so dramatically the cost per new installation has increased only by roughly an order of magnitude since the 1930's (corrected for inflation), while the number of accelerators operating at the frontier of the field has shrunk. As is shown in the by now familiar Livingston chart this dramatic decrease in cost has been achieved largely by a succession of new technologies, in addition to the more moderate gains in efficiency due to improved design, economies of scale, etc. We are therefore facing two questions: (1) Is there good reason scientifically to maintain the exponential growth, and (2) Are there new technologies in sight which promise continued decreases in unit costs. The answer to the first question is definitely yes; the answer to the second question is maybe

High Temperature Syngas Cleanup Technology Scale-up and Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Gardner, Ben [Research Triangle Inst. (RTI), Research Triangle Park, NC (United States); Turk, Brian [Research Triangle Inst. (RTI), Research Triangle Park, NC (United States); Denton, David [Research Triangle Inst. (RTI), Research Triangle Park, NC (United States); Gupta, Raghubir [Research Triangle Inst. (RTI), Research Triangle Park, NC (United States)

2015-09-30

Gasification is a technology for clean energy conversion of diverse feedstocks into a wide variety of useful products such as chemicals, fertilizers, fuels, electric power, and hydrogen. Existing technologies can be employed to clean the syngas from gasification processes to meet the demands of such applications, but they are expensive to build and operate and consume a significant fraction of overall parasitic energy requirements, thus lowering overall process efficiency. RTI International has developed a warm syngas desulfurization process (WDP) utilizing a transport-bed reactor design and a proprietary attrition-resistant, high-capacity solid sorbent with excellent performance replicated at lab, bench, and pilot scales. Results indicated that WDP technology can improve both efficiency and cost of gasification plants. The WDP technology achieved ~99.9% removal of total sulfur (as either H₂S or COS) from coal-derived syngas at temperatures as high as 600°C and over a wide range of pressures (20-80 bar, pressure independent performance) and sulfur concentrations. Based on the success of these tests, RTI negotiated a cooperative agreement with the U.S. Department of Energy for precommercial testing of this technology at Tampa Electric Company’s Polk Power Station IGCC facility in Tampa, Florida. The project scope also included a sweet water-gas-shift process for hydrogen enrichment and an activated amine process for 90+% total carbon capture. Because the activated amine process provides some additional non-selective sulfur removal, the integration of these processes was expected to reduce overall sulfur in the syngas to sub-ppmv concentrations, suitable for most syngas applications. The overall objective of this project was to mitigate the technical risks associated with the scale up and integration of the WDP and carbon dioxide capture technologies, enabling subsequent commercial-scale demonstration. The warm syngas cleanup pre-commercial test unit

Low Cost Lithography Tool for High Brightness LED Manufacturing

Energy Technology Data Exchange (ETDEWEB)

Andrew Hawryluk; Emily True

2012-06-30

The objective of this activity was to address the need for improved manufacturing tools for LEDs. Improvements include lower cost (both capital equipment cost reductions and cost-ofownership reductions), better automation and better yields. To meet the DOE objective of $1- 2/kilolumen, it will be necessary to develop these highly automated manufacturing tools. Lithography is used extensively in the fabrication of high-brightness LEDs, but the tools used to date are not scalable to high-volume manufacturing. This activity addressed the LED lithography process. During R&D and low volume manufacturing, most LED companies use contact-printers. However, several industries have shown that these printers are incompatible with high volume manufacturing and the LED industry needs to evolve to projection steppers. The need for projection lithography tools for LED manufacturing is identified in the Solid State Lighting Manufacturing Roadmap Draft, June 2009. The Roadmap states that Projection tools are needed by 2011. This work will modify a stepper, originally designed for semiconductor manufacturing, for use in LED manufacturing. This work addresses improvements to yield, material handling, automation and throughput for LED manufacturing while reducing the capital equipment cost.

In-Space Propulsion Technology Program Solar Electric Propulsion Technologies

Science.gov (United States)

Dankanich, John W.

2006-01-01

NASA's In-space Propulsion (ISP) Technology Project is developing new propulsion technologies that can enable or enhance near and mid-term NASA science missions. The Solar Electric Propulsion (SEP) technology area has been investing in NASA s Evolutionary Xenon Thruster (NEXT), the High Voltage Hall Accelerator (HiVHAC), lightweight reliable feed systems, wear testing, and thruster modeling. These investments are specifically targeted to increase planetary science payload capability, expand the envelope of planetary science destinations, and significantly reduce the travel times, risk, and cost of NASA planetary science missions. Status and expected capabilities of the SEP technologies are reviewed in this presentation. The SEP technology area supports numerous mission studies and architecture analyses to determine which investments will give the greatest benefit to science missions. Both the NEXT and HiVHAC thrusters have modified their nominal throttle tables to better utilize diminished solar array power on outbound missions. A new life extension mechanism has been implemented on HiVHAC to increase the throughput capability on low-power systems to meet the needs of cost-capped missions. Lower complexity, more reliable feed system components common to all electric propulsion (EP) systems are being developed. ISP has also leveraged commercial investments to further validate new ion and hall thruster technologies and to potentially lower EP mission costs.

High Speed, Low Cost Telemetry Access from Space Development Update on Programmable Ultra Lightweight System Adaptable Radio (PULSAR)

Science.gov (United States)

Simms, William Herbert, III; Varnavas, Kosta; Eberly, Eric

2014-01-01

Software Defined Radio (SDR) technology has been proven in the commercial sector since the early 1990's. Today's rapid advancement in mobile telephone reliability and power management capabilities exemplifies the effectiveness of the SDR technology for the modern communications market. In contrast, the foundations of transponder technology presently qualified for satellite applications were developed during the early space program of the 1960's. Conventional transponders are built to a specific platform and must be redesigned for every new bus while the SDR is adaptive in nature and can fit numerous applications with no hardware modifications. A SDR uses a minimum amount of analog / Radio Frequency (RF) components to up/down-convert the RF signal to/from a digital format. Once the signal is digitized, all processing is performed using hardware or software logic. Typical SDR digital processes include; filtering, modulation, up/down converting and demodulation. NASA Marshall Space Flight Center (MSFC) Programmable Ultra Lightweight System Adaptable Radio (PULSAR) leverages existing MSFC SDR designs and commercial sector enhanced capabilities to provide a path to a radiation tolerant SDR transponder. These innovations (1) reduce the cost of NASA Low Earth Orbit (LEO) and Deep Space standard transponders, (2) decrease power requirements, and (3) commensurately reduce volume. A second pay-off is the increased SDR flexibility by allowing the same hardware to implement multiple transponder types simply by altering hardware logic - no change of hardware is required - all of which will ultimately be accomplished in orbit. Development of SDR technology for space applications will provide a highly capable, low cost transponder to programs of all sizes. The MSFC PULSAR Project results in a Technology Readiness Level (TRL) 7 low-cost telemetry system available to Smallsat and CubeSat missions, as well as other platforms. This paper documents the continued development and

Enabling technologies for fiber optic sensing

Science.gov (United States)

Ibrahim, Selwan K.; Farnan, Martin; Karabacak, Devrez M.; Singer, Johannes M.

2016-04-01

In order for fiber optic sensors to compete with electrical sensors, several critical parameters need to be addressed such as performance, cost, size, reliability, etc. Relying on technologies developed in different industrial sectors helps to achieve this goal in a more efficient and cost effective way. FAZ Technology has developed a tunable laser based optical interrogator based on technologies developed in the telecommunication sector and optical transducer/sensors based on components sourced from the automotive market. Combining Fiber Bragg Grating (FBG) sensing technology with the above, high speed, high precision, reliable quasi distributed optical sensing systems for temperature, pressure, acoustics, acceleration, etc. has been developed. Careful design needs to be considered to filter out any sources of measurement drifts/errors due to different effects e.g. polarization and birefringence, coating imperfections, sensor packaging etc. Also to achieve high speed and high performance optical sensing systems, combining and synchronizing multiple optical interrogators similar to what has been used with computer/processors to deliver super computing power is an attractive solution. This path can be achieved by using photonic integrated circuit (PIC) technology which opens the doors to scaling up and delivering powerful optical sensing systems in an efficient and cost effective way.

High-Efficient Low-Cost Photovoltaics Recent Developments

CERN Document Server

Petrova-Koch, Vesselinka; Goetzberger, Adolf

2009-01-01

A bird's-eye view of the development and problems of recent photovoltaic cells and systems and prospects for Si feedstock is presented. High-efficient low-cost PV modules, making use of novel efficient solar cells (based on c-Si or III-V materials), and low cost solar concentrators are in the focus of this book. Recent developments of organic photovoltaics, which is expected to overcome its difficulties and to enter the market soon, are also included.

Benefits and costs of integrating technology into undergraduate nursing programs.

Science.gov (United States)

Glasgow, Mary Ellen Smith; Cornelius, Frances H

2005-01-01

Advances in technology over the last decade have resulted in increased opportunities for educators to become more innovative in classroom and clinical teaching. These innovations have allowed students and faculty to access essential clinical information at the point of care/need. By capitalizing on technologies such as personal digital assistants and course delivery shells, faculty and students have both portable and remote access to information that can guide practice and learning activities in clinical, classroom, and distance settings. For instance, a student can use a personal digital assistant to research a patient's new medication at the bedside, study course information, access references during class in response to a question, or download clinical materials from home. Although the benefits of having ready access to information seem obvious, there are costs and strategic planning activities associated with implementing these projects. Clearly, the objective of any academic nursing program is to develop skills among students so they can efficiently access information and use that information to guide their nursing practice. To do so, academic nursing administrators must have the forethought to envision how new technologies can support achieving this goal as well as the ability to put in place the infrastructure supports needed for success. This article presents a case study of how one institution developed the necessary infrastructure and garnished the appropriate resources to implement an ambitious technology initiative integrated throughout a large undergraduate nursing program. In addition, how the integration of technology, online and mobile, can enhance clinical learning will be discussed.

The Perceived Effect of Hidden Costs on the Operational Management of Information Technology Outsourcing: A Qualitative Study

Science.gov (United States)

Swift, Ian

2011-01-01

Information technology (IT) outsourcing is a business trend aimed at reducing costs and enabling companies to concentrate on their core competencies. This qualitative multiple case design research study explored the effects of hidden costs on the operational management of IT outsourcing. The study involved analyzing IT outsourcing agreements as…

Improvement of the cost-benefit analysis algorithm for high-rise construction projects

Directory of Open Access Journals (Sweden)

Gafurov Andrey

2018-01-01

Full Text Available The specific nature of high-rise investment projects entailing long-term construction, high risks, etc. implies a need to improve the standard algorithm of cost-benefit analysis. An improved algorithm is described in the article. For development of the improved algorithm of cost-benefit analysis for high-rise construction projects, the following methods were used: weighted average cost of capital, dynamic cost-benefit analysis of investment projects, risk mapping, scenario analysis, sensitivity analysis of critical ratios, etc. This comprehensive approach helped to adapt the original algorithm to feasibility objectives in high-rise construction. The authors put together the algorithm of cost-benefit analysis for high-rise construction projects on the basis of risk mapping and sensitivity analysis of critical ratios. The suggested project risk management algorithms greatly expand the standard algorithm of cost-benefit analysis in investment projects, namely: the “Project analysis scenario” flowchart, improving quality and reliability of forecasting reports in investment projects; the main stages of cash flow adjustment based on risk mapping for better cost-benefit project analysis provided the broad range of risks in high-rise construction; analysis of dynamic cost-benefit values considering project sensitivity to crucial variables, improving flexibility in implementation of high-rise projects.

Improvement of the cost-benefit analysis algorithm for high-rise construction projects

Science.gov (United States)

Gafurov, Andrey; Skotarenko, Oksana; Plotnikov, Vladimir

2018-03-01

The specific nature of high-rise investment projects entailing long-term construction, high risks, etc. implies a need to improve the standard algorithm of cost-benefit analysis. An improved algorithm is described in the article. For development of the improved algorithm of cost-benefit analysis for high-rise construction projects, the following methods were used: weighted average cost of capital, dynamic cost-benefit analysis of investment projects, risk mapping, scenario analysis, sensitivity analysis of critical ratios, etc. This comprehensive approach helped to adapt the original algorithm to feasibility objectives in high-rise construction. The authors put together the algorithm of cost-benefit analysis for high-rise construction projects on the basis of risk mapping and sensitivity analysis of critical ratios. The suggested project risk management algorithms greatly expand the standard algorithm of cost-benefit analysis in investment projects, namely: the "Project analysis scenario" flowchart, improving quality and reliability of forecasting reports in investment projects; the main stages of cash flow adjustment based on risk mapping for better cost-benefit project analysis provided the broad range of risks in high-rise construction; analysis of dynamic cost-benefit values considering project sensitivity to crucial variables, improving flexibility in implementation of high-rise projects.

Additive Manufacturing of Low Cost Upper Stage Propulsion Components

Science.gov (United States)

Protz, Christopher; Bowman, Randy; Cooper, Ken; Fikes, John; Taminger, Karen; Wright, Belinda

2014-01-01

NASA is currently developing Additive Manufacturing (AM) technologies and design tools aimed at reducing the costs and manufacturing time of regeneratively cooled rocket engine components. These Low Cost Upper Stage Propulsion (LCUSP) tasks are funded through NASA's Game Changing Development Program in the Space Technology Mission Directorate. The LCUSP project will develop a copper alloy additive manufacturing design process and develop and optimize the Electron Beam Freeform Fabrication (EBF3) manufacturing process to direct deposit a nickel alloy structural jacket and manifolds onto an SLM manufactured GRCop chamber and Ni-alloy nozzle. In order to develop these processes, the project will characterize both the microstructural and mechanical properties of the SLMproduced GRCop-84, and will explore and document novel design techniques specific to AM combustion devices components. These manufacturing technologies will be used to build a 25K-class regenerative chamber and nozzle (to be used with tested DMLS injectors) that will be tested individually and as a system in hot fire tests to demonstrate the applicability of the technologies. These tasks are expected to bring costs and manufacturing time down as spacecraft propulsion systems typically comprise more than 70% of the total vehicle cost and account for a significant portion of the development schedule. Additionally, high pressure/high temperature combustion chambers and nozzles must be regeneratively cooled to survive their operating environment, causing their design to be time consuming and costly to build. LCUSP presents an opportunity to develop and demonstrate a process that can infuse these technologies into industry, build competition, and drive down costs of future engines.

Low-Cost Superconducting Wire for Wind Generators: High Performance, Low Cost Superconducting Wires and Coils for High Power Wind Generators

Energy Technology Data Exchange (ETDEWEB)

None

2012-01-01

REACT Project: The University of Houston will develop a low-cost, high-current superconducting wire that could be used in high-power wind generators. Superconducting wire currently transports 600 times more electric current than a similarly sized copper wire, but is significantly more expensive. The University of Houston’s innovation is based on engineering nanoscale defects in the superconducting film. This could quadruple the current relative to today’s superconducting wires, supporting the same amount of current using 25% of the material. This would make wind generators lighter, more powerful and more efficient. The design could result in a several-fold reduction in wire costs and enable their commercial viability of high-power wind generators for use in offshore applications.

"Water-in-salt" electrolytes enable the use of cost-effective aluminum current collectors for aqueous high-voltage batteries.

Science.gov (United States)

Kühnel, R-S; Reber, D; Remhof, A; Figi, R; Bleiner, D; Battaglia, C

2016-08-16

The extended electrochemical stability window offered by highly concentrated electrolytes allows the operation of aqueous batteries at voltages significantly above the thermodynamic stability limit of water, at which the stability of the current collector potentially limits the cell voltage. Here we report the observation of suppressed anodic dissolution of aluminum in "water-in-salt" electrolytes enabling roll-to-roll electrode fabrication for high-voltage aqueous lithium-ion batteries on cost-effective light-weight aluminum current collectors using established lithium-ion battery technology.

Technological cost-reduction pathways for attenuator wave energy converters in the marine hydrokinetic environment.

Energy Technology Data Exchange (ETDEWEB)

Bull, Diana L; Ochs, Margaret Ellen

2013-09-01

This report considers and prioritizes the primary potential technical costreduction pathways for offshore wave activated body attenuators designed for ocean resources. This report focuses on technical research and development costreduction pathways related to the device technology rather than environmental monitoring or permitting opportunities. Three sources of information were used to understand current cost drivers and develop a prioritized list of potential costreduction pathways: a literature review of technical work related to attenuators, a reference device compiled from literature sources, and a webinar with each of three industry device developers. Data from these information sources were aggregated and prioritized with respect to the potential impact on the lifetime levelized cost of energy, the potential for progress, the potential for success, and the confidence in success. Results indicate the five most promising costreduction pathways include advanced controls, an optimized structural design, improved power conversion, planned maintenance scheduling, and an optimized device profile.

Are Green Vehicles Worth the Extra Cost? The Case of Diesel-Electric Hybrid Technology for Urban Delivery Vehicles