First plasma of the A-PHOENIX electron cyclotron resonance ion source

International Nuclear Information System (INIS)

Thuillier, T.; Lamy, T.; Latrasse, L.; Angot, J.

2008-01-01

A-PHOENIX is a new compact hybrid electron cyclotron resonance ion source using a large permanent magnet hexapole (1.92 T at the magnet surface) and high temperature superconducting Solenoids (3 T) to make min-vertical bar B vertical bar structure suitable for 28 GHz cw operation. The final assembly of the source was achieved at the end of June 2007. The first plasma of A-PHOENIX at 18 GHz was done on the 16th of August, 2007. The technological specificities of A-PHOENIX are presented. The large hexapole built is presented and experimental magnetic measurements show that it is nominal with respect to simulation. A fake plasma chamber prototype including thin iron inserts showed that the predicted radial magnetic confinement can be fulfilled up to 2.15 T at the plasma chamber wall. Scheduled planning of experiments until the end of 2008 is presented

A Comparative Electrochemical Study of AZ31 and AZ91 Magnesium Alloy

Directory of Open Access Journals (Sweden)

S. A. Salman

2010-01-01

Full Text Available A comparative study has been carried out on AZ31 and AZ91 magnesium alloys in order to understand the electrochemical behavior in both alkaline and chloride containing solutions. The open circuit potential (OCP was examined in 1 M NaOH and 3.5 mass % NaCl solutions. AZ31 magnesium alloy shows several potential drops throughout the immersion in 1 M NaOH solution, though AZ91 does not show this phenomenon. The specimens were anodized at a constant potential of 3 V for 30 minutes at 298 K in 1 M NaOH solution. The anticorrosion behavior of the anodized specimens was better than those of nonanodized specimens. The anodized AZ91 has better corrosion resistance compared to nonanodized specimen and anodized AZ31 magnesium alloy.

Phoenix's Lay of the Land

Science.gov (United States)

2008-01-01

This image from NASA's Phoenix Mars Lander shows the spacecraft's recent activity site as of the 23rd Martian day of the mission, or Sol 22 (June 16, 2008), after the spacecraft touched down on the Red Planet's northern polar plains. The mosaic was taken by the lander's Surface Stereo Imager (SSI). Parts of Phoenix can be seen in the foreground. The first two trenches dug by the lander's Robotic Arm, called 'Dodo' and 'Goldilocks,' were enlarged on the 19th Martian day of the mission, or Sol 18 (June 12, 2008), to form one trench, dubbed 'Dodo-Goldilocks.' Scoops of material taken from those trenches are informally called 'Baby Bear' and 'Mama Bear.' Baby Bear was carried to Phoenix's Thermal and Evolved-Gas Analyzer, or TEGA, instrument for analysis, while Mama Bear was delivered to Phoenix's Microscopy, Electrochemistry and Conductivity Analyzer instrument suite, or MECA, for a closer look. The color inset picture of the Dodo-Goldilocks trench, also taken with Phoenix's SSI, reveals white material thought to be ice. More recently, on Sol 22 (June 16, 2008), Phoenix's Robotic Arm began digging a trench, dubbed 'Snow White,' in a patch of Martian soil near the center of a polygonal surface feature, nicknamed 'Cheshire Cat.' The 'dump pile' is located at the top of the trench, and has been dubbed 'Croquet Ground.' The digging site has been nicknamed 'Wonderland.' The Snow White trench, seen here in an SSI image from Sol 22 (June 16, 2008) is about 2 centimeters (.8 inches) deep and 30 centimeters (12 inches) long. As of Sol 25 (June 19, 2008), the trench is 5 centimeters (2 inches deep) and the trench has been renamed 'Snow White 1,' as a second trench has been dug to its right and nicknamed 'Snow White 2.' The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

Phoenix Study

Data.gov (United States)

U.S. Environmental Protection Agency — Phoenix Traffic and Mobile Data. This dataset is associated with the following publication: Baldauf , R., V. Isakov , P. Deshmukh, and A. Venkatram. Influence of...

Wood Polymer Composites Technology Supporting the Recovery and Protection of Tropical Forests: The Amazonian Phoenix Project

Directory of Open Access Journals (Sweden)

Antonio D. Nobre

2009-12-01

Full Text Available The Amazon Rain Forest has attracted worldwide attention due its large scale services to climate and also due to the green house gas emissions arising from deforestation. Contributing to the later and detrimental to the former, timber logging in the region has very low efficiency (only 16% in the production chain. Such timber extraction, often referred to as selective logging, has been claimed as a sustainable extractive industry, because the forest is said to restore itself through regenerative growth. But forest regeneration in the Amazon occurs naturally only in a very limited scale, resulting that large scale, low efficiency logging poses a big treat to the functional integrity of the biome, supplying to the market only a fraction of what it could if done differently. So, instead of extracting big centennial logs from the forests, the Amazonian Phoenix project proposes that large expanses of degraded lands be reforested using pioneer plants species from the forest itself. These plants have the capacity to heal gaps in the canopy, being able to grow and produce woody biomass in very extreme conditions. The idea is to mimic the regenerative dynamics of the natural ecosystem in short cycle agrosilvicultural production areas, utilizing a variety of technologies to transform raw fibers from these fast growth native plants into a variety of materials with high aggregated value. This communication presents the research on natural fibers by the Polymeric Composites Group within the Amazonian Phoenix Project. Sustainable technologies employing materials with good and responsible ecological footprints are important and necessary stimulus for a change in the destructive economical activities present in the Amazon frontiers. The relatively well established wood polymer composites technology, for example, is a good candidate solution. Two research and development fields are proposed: the first one considers production systems with simple and cheap

Phoenix Trenches

Science.gov (United States)

2008-01-01

[figure removed for brevity, see original site] Annotated Version [figure removed for brevity, see original site] Left-eye view of a stereo pair [figure removed for brevity, see original site] Right-eye view of a stereo pair This image is a stereo, panoramic view of various trenches dug by NASA's Phoenix Mars Lander. The images that make up this panorama were taken by Phoenix's Surface Stereo Imager at about 4 p.m., local solar time at the landing site, on the 131st, Martian day, or sol, of the mission (Oct. 7, 2008). In figure 1, the trenches are labeled in orange and other features are labeled in blue. Figures 2 and 3 are the left- and right-eye members of a stereo pair. For scale, the 'Pet Donkey' trench just to the right of center is approximately 38 centimeters (15 inches) long and 31 to 34 centimeters (12 to 13 inches) wide. In addition, the rock in front of it, 'Headless,' is about 11.5 by 8.5 centimeters (4.5 by 3.3 inches), and about 5 centimeters (2 inches) tall. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

Cold-Sprayed AZ91D Coating and SiC/AZ91D Composite Coatings

Directory of Open Access Journals (Sweden)

Yingying Wang

2018-03-01

Full Text Available As an emerging coating building technique, cold spraying has many advantages to elaborate Mg alloy workpieces. In this study, AZ91D coatings and AZ91D-based composite coatings were deposited using cold spraying. Coatings were prepared using different gas temperatures to obtain the available main gas temperature. Compressed air was used as the accelerating gas, and although magnesium alloy is oxidation-sensitive, AZ91D coatings with good performance were obtained. The results show that dense coatings can be fabricated until the gas temperature is higher than 500 °C. The deposition efficiency increases greatly with the gas temperature, but it is lower than 10% for all coating specimens. To analyze the effects of compressed air on AZ91D powder particles and the effects of gas temperature on coatings, the phase composition, porosity, cross-sectional microstructure, and microhardness of coatings were characterized. X-ray diffraction and oxygen content analysis clarified that no phase transformation or oxidation occurred on AZ91D powder particles during cold spraying processes with compressed air. The porosity of AZ91D coatings remained between 3.6% and 3.9%. Impact melting was found on deformed AZ91D particles when the gas temperature increased to 550 °C. As-sprayed coatings exhibit much higher microhardness than as-casted bulk magnesium, demonstrating the dense structure of cold-sprayed coatings. To study the effects of ceramic particles on cold-sprayed AZ91D coatings, 15 vol % SiC powder particles were added into the feedstock powder. Lower SiC content in the coating than in the feedstock powder means that the deposition efficiency of the SiC powder particles is lower than the deposition efficiency of AZ91D particles. The addition of SiC particles reduces the porosity and increases the microhardness of cold-sprayed AZ91D coatings. The corrosion behavior of AZ91D coating and SiC reinforced AZ91D composite coating were examined. The Si

Alternative Fuels Data Center: Phoenix Cleans Up with Natural Gas

Science.gov (United States)

Phoenix Cleans Up with Natural Gas to someone by E-mail Share Alternative Fuels Data Center : Phoenix Cleans Up with Natural Gas on Facebook Tweet about Alternative Fuels Data Center: Phoenix Cleans Up with Natural Gas on Twitter Bookmark Alternative Fuels Data Center: Phoenix Cleans Up with Natural

Descriptive Summaries of the Research, Development, Test and Evaluation, Army Appropriation. Supporting Data FY 1994, Budget Estimates Submitted to Congress, April 1993

Science.gov (United States)

1993-04-01

Investigate the genetics and physiology of Yersinia pestis, Brucella Sp., Q-fever, Vibrio cholerae , Francisella tularensis and Bacillus anthracis "* (U) Conduct...New Mexico State University, NM; Optimetrics, Inc., Ann Arbor, MI; Massachusetts Institute of Technology. Cambridge, MA; Mission Research Corporation...Laboratory (ARL), Adelphi, MD. Contractors include: New Mexico Institute of Mining and Technology, Socorro, NM; Dynamic Sciences, Inc., Phoenix, AZ; Honeywell

US Geological Survey National Computer Technology Meeting; Proceedings, Phoenix, Arizona, November 14-18, 1988

Science.gov (United States)

Balthrop, Barbara H.; Terry, J.E.

1991-01-01

The U.S. Geological Survey National Computer Technology Meetings (NCTM) are sponsored by the Water Resources Division and provide a forum for the presentation of technical papers and the sharing of ideas or experiences related to computer technology. This report serves as a proceedings of the meeting held in November, 1988 at the Crescent Hotel in Phoenix, Arizona. The meeting was attended by more than 200 technical and managerial people representing all Divisions of the U.S. Geological Survey.Scientists in every Division of the U.S. Geological Survey rely heavily upon state-of-the-art computer technology (both hardware and sofnuare). Today the goals of each Division are pursued in an environment where high speed computers, distributed communications, distributed data bases, high technology input/output devices, and very sophisticated simulation tools are used regularly. Therefore, information transfer and the sharing of advances in technology are very important issues that must be addressed regularly.This report contains complete papers and abstracts of papers that were presented at the 1988 NCTM. The report is divided into topical sections that reflect common areas of interest and application. In each section, papers are presented first followed by abstracts. For these proceedings, the publication of a complete paper or only an abstract was at the discretion of the author, although complete papers were encouraged.Some papers presented at the 1988 NCTM are not published in these proceedings.

Microstructure of AZ31 Magnesium Alloy deformed by indentation-flattening compound deformation technology

Science.gov (United States)

Wang, Minghao; Wang, Zhongtang; Yu, Xiaolin

2018-03-01

Characteristic of indentation-flattening compound deformation technology (IFCDT) is discussed, and the parameters of IFCDT are defined. Performance of magnesium alloy AZ31 sheet deformed by IFCDT is researched. The effect of IFCDT coefficient, temperature and reduction ratio on the microstructure of magnesium alloy sheet is analyzed. The research results show that the volume fraction of the twin crystal decreases gradually and the average grain size increases with increasing of coefficient of IFCDT. With increase of the reduction ratio, the volume fraction of the twin crystal gradually increases, and the average grain size also increases. With increase of deformation temperature, the volume fraction of the twin crystal decreases gradually, and the twin crystal grain size increases.

Pathogen and nutrient pulsing and attenuation in "accidental" urban wetland networks along the Salt River in Phoenix, AZ

Science.gov (United States)

Palta, M. M.; Grimm, N. B.

2013-12-01

Increases in available nutrients and bacteria in urban streams are at the forefront of research concerns within the ecological and medical communities, and both pollutants are expected to become more problematic under projected changes in climate. Season, discharge, instream conditions (oxygen, water velocity), and weather conditions (antecedent moisture) all may influence loading rates to and the retention capabilities of wetlands fed by urban runoff and storm flow. The aim of this research was to examine the effect of these variables on nutrient (nitrogen, phosphorus) and Escherichia coli (E. coli) loading and attenuation along flow paths in urban wetland networks along the Salt River in Phoenix, AZ. Samples were collected for one year along flowpaths through wetlands that formed below six perennially flowing outfalls. Collection took place monthly during baseflow (dry season) conditions, and before and immediately following storm events, in the summer monsoon and winter rainy seasons. Water quality was assessed at the following points: immediately downstream of the outfall, mid-wetland, and downstream of the wetland. For determination of E. coli counts, samples were plated on coliform-selective media (Chromocult) and incubated for 24 hours. Plates were then used to enumerate E. coli. For determination of nutrient concentrations, samples were filtered and frozen until they could be analyzed by ion chromatography and automated wet chemistry. During both summer and winter, total discharge into the wetlands increased during storm events. Concentrations of PO43+, NH4+, and E. coli were significantly higher following storm events than during baseflow conditions, and post-storm peaks in concentration ('pulses') were higher during the summer monsoon than in winter storms. Pulses of pollutants during storms were highest when preceded by hot, dry conditions. NO3- was high in both base and stormflow. E. coli counts and nutrient concentrations dropped along flowpaths

Traumatic brain injury and vestibulo-ocular function: current challenges and future prospects

Directory of Open Access Journals (Sweden)

Wallace B

2016-09-01

Full Text Available Bridgett Wallace,1–4 Jonathan Lifshitz4–8 1360 Balance and Hearing, Department of Physical Therapy, Austin, TX, 2Concussion Health, Department of Clinical Education, Austin, TX, 3Conquering Concussions, Scottsdale, AZ, 4Barrow Neurological Institute at Phoenix Children’s Hospital, Phoenix, AZ, 5Department of Child Health, University of Arizona College of Medicine-Phoenix, Phoenix, AZ, 6The CACTIS Foundation, Scottsdale, 7Phoenix VA Healthcare System, Phoenix, AZ, 8Department of Psychology, Arizona State University, Tempe, AZ, USA Abstract: Normal function of the vestibulo-ocular reflex (VOR coordinates eye movement with head movement, in order to provide clear vision during motion and maintain balance. VOR is generated within the semicircular canals of the inner ear to elicit compensatory eye movements, which maintain stability of images on the fovea during brief, rapid head motion, otherwise known as gaze stability. Normal VOR function is necessary in carrying out activities of daily living (eg, walking and riding in a car and is of particular importance in higher demand activities (eg, sports-related activities. Disruption or damage in the VOR can result in symptoms such as movement-related dizziness, blurry vision, difficulty maintaining balance with head movements, and even nausea. Dizziness is one of the most common symptoms following traumatic brain injury (TBI and is considered a risk factor for a prolonged recovery. Assessment of the vestibular system is of particular importance following TBI, in conjunction with oculomotor control, due to the intrinsic neural circuitry that exists between the ocular and vestibular systems. The purpose of this article is to review the physiology of the VOR and the visual-vestibular symptoms associated with TBI and to discuss assessment and treatment guidelines for TBI. Current challenges and future prospects will also be addressed. Keywords: traumatic brain injury, concussion, vestibular, ocular

Tank 241-AZ-101 and tank 241-AZ-102, airlift circulator operation vapor sampling and analysis plan

International Nuclear Information System (INIS)

TEMPLETON, A.M.

1999-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for vapor samples obtained during the operation of the tank 241-AZ-101 and 241-AZ-102 airlift circulators (ALCs). The purpose of the ALC operation is to support portions of the operational test procedure (OTP) for Project W-030 (OTP-W030-001) and to perform functional test in support of Project W-151. Project W-030 is the 241-A-702 ventilation upgrade project (241-AZ-702) and Project W-151 is the 241-AZ-101 Mixer Pump Test. The functional tests will check the operability of the tank 241-AZ-101 ALCs. Process Memo's No.2E98-082 and No.2E99-001 (LMHC 1999a, LMHC 1999b) direct the operation of the ALCs and the Industrial Hygiene monitoring respectively. A series of tests will be conducted in which the ALCs in tanks 241-AZ-101 and 241-AZ-102 will be operated at different air flow rates. Vapor samples will be obtained to determine constituents that may be present in the tank headspace during ALC operation at tanks 241-AZ-101 and 241-AZ-102 as the waste is disturbed. During the testing, vapor samples will be obtained from the headspace of tanks 241-AZ-101 and 241-AZ-102 via the unused port on the standard hydrogen monitoring system (SHMS). Results will be used to provide the waste feed delivery program with environmental air permitting data for tank waste disturbing activities. Because of radiological concerns, the samples will be filtered for particulates. It is recognized that this may remove some organic compounds

Comparison of some Phoenix and gusev soil types

DEFF Research Database (Denmark)

Walter..[], Goetz; Hviid, S.F.; Madsen, Morten Bo

2010-01-01

The comparison of soil particles at the Phoenix landing site and in Gusev Crater provides clues on their origin and global distribution. Some unusual Phoenix particles are possibly of (more) local origin, as they appear to be absent in Gusev dunes....

Rapid coating of AZ31 magnesium alloy with calcium deficient hydroxyapatite using microwave energy

International Nuclear Information System (INIS)

Ren, Yufu; Zhou, Huan; Nabiyouni, Maryam; Bhaduri, Sarit B.

2015-01-01

Due to their unique biodegradability, magnesium alloys have been recognized as suitable metallic implant materials for degradable bone implants and bioresorbable cardiovascular stents. However, the extremely high degradation rate of magnesium alloys in physiological environment has restricted its practical application. This paper reports the use of a novel microwave assisted coating technology to improve the in vitro corrosion resistance and biocompatibility of Mg alloy AZ31. Results indicate that a dense calcium deficient hydroxyapatite (CDHA) layer was uniformly coated on a AZ31 substrate in less than 10 min. Weight loss measurement and SEM were used to evaluate corrosion behaviors in vitro of coated samples and of non-coated samples. It was seen that CDHA coatings remarkably reduced the mass loss of AZ31 alloy after 7 days of immersion in SBF. In addition, the prompt precipitation of bone-like apatite layer on the sample surface during immersion demonstrated a good bioactivity of the CDHA coatings. Proliferation of osteoblast cells was promoted in 5 days of incubation, which indicated that the CDHA coatings could improve the cytocompatibility of the AZ31 alloy. All the results suggest that the CDHA coatings, serving as a protective layer, can enhance the corrosion resistance and biological response of magnesium alloys. Furthermore, this microwave assisted coating technology could be a promising method for rapid surface modification of biomedical materials. - Highlights: • A microwave assisted coating process for biodegradable Mg alloy. • CDHA coatings were successfully developed on AZ31 alloy in minutes. • The as-deposited CDHA coatings significantly reduced the degradation rate of AZ31 alloy. • The CDHA coated AZ31 alloy showed good bioactivity and biocompatibility in vitro. • The microwave assisted coating process can be used as rapid surface modification for bioimplants

Rapid coating of AZ31 magnesium alloy with calcium deficient hydroxyapatite using microwave energy

Energy Technology Data Exchange (ETDEWEB)

Ren, Yufu, E-mail: Yufu.Ren@rockets.utoledo.edu [Department of Mechanical, Industrial and Manufacturing Engineering, The University of Toledo, Toledo, OH (United States); Zhou, Huan [Department of Mechanical, Industrial and Manufacturing Engineering, The University of Toledo, Toledo, OH (United States); Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou, Jiangsu (China); Nabiyouni, Maryam [Department of Bioengineering, The University of Toledo, Toledo, OH (United States); Bhaduri, Sarit B. [Department of Mechanical, Industrial and Manufacturing Engineering, The University of Toledo, Toledo, OH (United States); Division of Dentistry, The University of Toledo, Toledo, OH (United States)

2015-04-01

Due to their unique biodegradability, magnesium alloys have been recognized as suitable metallic implant materials for degradable bone implants and bioresorbable cardiovascular stents. However, the extremely high degradation rate of magnesium alloys in physiological environment has restricted its practical application. This paper reports the use of a novel microwave assisted coating technology to improve the in vitro corrosion resistance and biocompatibility of Mg alloy AZ31. Results indicate that a dense calcium deficient hydroxyapatite (CDHA) layer was uniformly coated on a AZ31 substrate in less than 10 min. Weight loss measurement and SEM were used to evaluate corrosion behaviors in vitro of coated samples and of non-coated samples. It was seen that CDHA coatings remarkably reduced the mass loss of AZ31 alloy after 7 days of immersion in SBF. In addition, the prompt precipitation of bone-like apatite layer on the sample surface during immersion demonstrated a good bioactivity of the CDHA coatings. Proliferation of osteoblast cells was promoted in 5 days of incubation, which indicated that the CDHA coatings could improve the cytocompatibility of the AZ31 alloy. All the results suggest that the CDHA coatings, serving as a protective layer, can enhance the corrosion resistance and biological response of magnesium alloys. Furthermore, this microwave assisted coating technology could be a promising method for rapid surface modification of biomedical materials. - Highlights: • A microwave assisted coating process for biodegradable Mg alloy. • CDHA coatings were successfully developed on AZ31 alloy in minutes. • The as-deposited CDHA coatings significantly reduced the degradation rate of AZ31 alloy. • The CDHA coated AZ31 alloy showed good bioactivity and biocompatibility in vitro. • The microwave assisted coating process can be used as rapid surface modification for bioimplants.

'Rosy Red' Soil in Phoenix's Scoop

Science.gov (United States)

2008-01-01

This image shows fine-grained material inside the Robotic Arm scoop as seen by the Robotic Arm Camera (RAC) aboard NASA's Phoenix Mars Lander on June 25, 2008, the 30th Martian day, or sol, of the mission. The image shows fine, fluffy, red soil particles collected in a sample called 'Rosy Red.' The sample was dug from the trench named 'Snow White' in the area called 'Wonderland.' Some of the Rosy Red sample was delivered to Phoenix's Optical Microscope and Wet Chemistry Laboratory for analysis. The RAC provides its own illumination, so the color seen in RAC images is color as seen on Earth, not color as it would appear on Mars. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

GMAP Phoenix 2013 data

Data.gov (United States)

U.S. Environmental Protection Agency — mobile monitoring data from the 2013 Phoenix study. This dataset is associated with the following publication: Venkatram, A., V. Isakov , P. Deshmukh, and R....

Advancing electric-vehicle development with pure-lead-tin battery technology

Science.gov (United States)

O'Brien, W. A.; Stickel, R. B.; May, G. J.

Electric-vehicle (EV) development continues to make solid progress towards extending vehicle range, reliability and ease of use, aided significantly by technological advances in vehicle systems. There is, however, a widespread misconception that current battery technologies are not capable of meeting even the minimum user requirements that would launch EVs into daily use. Existing pure-lead-tin technology is moving EVs out of research laboratories and onto the streets, in daily side-by-side operation with vehicles powered by conventional gasoline and alternative fuels. This commercially available battery technology can provide traffic-compatible performance in a reliable and affordable manner, and can be used for either pure EVs or hybrid electric vehicles (HEVs). Independent results obtained when applying lead-tin batteries in highly abusive conditions, both electrically and environmentally, are presented. The test fleet of EVs is owned and operated by Arizona Public Service (APS), an electric utility in Phoenix, AZ, USA. System, charger and battery development will be described. This gives a single charge range of up to 184 km at a constant speed of 72 km h -1, and with suitable opportunity charging, a 320 km range in a normal 8 h working day.

A comparative corrosion behavior of Mg, AZ31 and AZ91 alloys in 3.5% NaCl solution

Directory of Open Access Journals (Sweden)

I.B. Singh

2015-06-01

Full Text Available The corrosion behavior of Mg, AZ31 and AZ91 has been evaluated in 3.5% NaCl solution using weight loss, electrochemical polarization and impedance measurements. Corrosion rate derived from the weight losses demonstrated the occurrence of steeply fast corrosion reaction on AZ91 alloy after three hours of immersion, indicating the start of galvanic corrosion. An increase of corrosion rate with immersion time was also observed for AZ31 but with lesser extent than AZ91 alloy. Whereas Mg metals showed a decrease of corrosion rate with immersion time, suggesting the formation of a protective layer on their surfaces. In contrast, the corrosion current density (Icorr derived from the Tafel plots, exhibited their corrosion resistances in order of Mg > AZ91 > AZ31. Electrochemical charge transfer resistance (Rct and double layer capacitance measured by electrochemical impedance spectroscopy (EIS, are well in accordance with the measured Icorr. EIS measurements with time and microstructural examination of the corroded and uncorroded samples are helpful in elucidation of results measured by electrochemical polarization.

78 FR 24765 - Notice of Intent To Close 16 Field Offices

Science.gov (United States)

2013-04-26

...; Dallas, TX; Lubbock, TX; Tucson, AZ; Fresno, CA; Sacramento, CA; San Diego, CA; and Spokane, WA. HUD is..., AZ; Fresno, CA; Sacramento, CA; San Diego, CA; and Spokane, WA. Employees who work in the... office--HUD will retain the field office in Phoenix, AZ. j. Sacramento, San Diego, and Fresno field...

Artificial tears potpourri: a literature review

OpenAIRE

Moshirfar, Majid; Pierson, Kasey; Hanamaikai, Kamalani; Santiago-Caban, Luis; Muthappan, Valliammai; Passi, Samuel F

2014-01-01

Majid Moshirfar,1 Kasey Pierson,2,* Kamalani Hanamaikai,3,* Luis Santiago-Caban,1 Valliammai Muthappan,1 Samuel F Passi11Department of Ophthalmology, John A Moran Eye Center, University of Utah, Salt Lake City, UT, USA; 2University of Arizona College of Medicine, Phoenix, Phoenix, AZ, USA; 3A T Still University, School of Osteopathic Medicine in Arizona, Mesa, AZ, USA *These authors contributed equally to this work Abstract: Numerous brands and types of artificial tears are available on the...

Joining of AZ31 and AZ91 Mg alloys by friction stir welding

Directory of Open Access Journals (Sweden)

B. Ratna Sunil

2015-12-01

Full Text Available Two dissimilar magnesium (Mg alloy sheets, one with low aluminium (AZ31 and another with high aluminium (AZ91 content, were successfully joined by friction stir welding (FSW. The effect of process parameters on the formation of hot cracks was investigated. A sound metallurgical joint was obtained at optimized process parameters (1400 rpm with 25 mm/min feed which contained fine grains and distributed β (Mg17Al12 phase within the nugget zone. An increasing trend in the hardness measurements has also confirmed more amount of dissolution of aluminium within the nugget zone. A sharp interface between nugget zone and thermo mechanical affected zone (TMAZ was clearly noticed at the AZ31 Mg alloy side (advancing but not on the AZ91 Mg alloy side (retreating. From the results it can be concluded that FSW can be effectively used to join dissimilar metals, particularly difficult to process metals such as Mg alloys, and hot cracking can be completely eliminated by choosing appropriate process parameters to achieve sound joint.

'Dodo-Goldilocks' Trench Dug by Phoenix

Science.gov (United States)

2008-01-01

This color image was acquired by NASA's Phoenix Mars Lander's Surface Stereo Imager on the 19th day of the mission, or Sol 19 (June 13, 2008), after the May 25, 2008, landing. This image shows one trench informally called 'Dodo-Goldilocks' after two digs (dug on Sol 18, or June 12, 2008) by Phoenix's Robotic Arm. The trench is 22 centimeters (8.7 inches) wide and 35 centimeters (13.8 inches) long. At its deepest point, the trench is 7 to 8 centimeters (2.7 to 3 inches) deep. White material, possibly ice, is located only at the upper portion of the trench, indicating that it is not continuous throughout the excavated site. According to scientists, the trench might be exposing a ledge, or only a portion of a slab, of the white material. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

Project Phoenix and beyond. Pesek Lecture.

Science.gov (United States)

Tarter, J

1997-01-01

Although there are no federally funded projects at this time, SETI (the search for extraterrestrial intelligence) is a vigorous exploratory science. There are currently eight observational programs on telescopes around the world, of which the Phoenix Project is the most comprehensive. Most of these projects are rooted in the conclusions of the pioneering studies of the early 1970's that are summarized in the Cyclops Report. Technology has experienced an exponential growth over the past two and a half decades. It is reasonable to reassess the Cyclops conclusions as SETI enters the next century. Listening for radio signals is still the preferred method of searching, however new technologies are making searches at other wavelengths possible and are modifying the ways in which the radio searches can and should be conducted. It may be economically feasible to undertake the construction of very large telescopes that can simultaneously provide multiple beams on the sky for use by SETI and the radioastronomy community.

Pesek lecture project Phoenix and beyond

Science.gov (United States)

Tarter, Jill

Although there are no federally funded projects at this time, SETI (the search for extraterrestrial intelligence) is a vigorous exploratory science. There are currently eight observational programs on telescopes around the world, of which the Phoenix Project is the most comprehensive. Most of these projects are rooted in the conclusions of the pioneering studies of the early 1970's that are summarized in the Cyclops Report1. Technology has experienced an exponential growth over the past two and a half decades. It is reasonable to reassess the Cyclops conclusions as SETI enters the next century. Listening for radio signals is still the preferred method of searching, however new technologies are making searches at other wavelengths possible and are modifying the ways in which the radio searches can and should be conducted. It may be economically feasible to undertake the construction of very large telescopes that can simultaneously provide multiple beams on the sky for use by SETI and the radioastronomy community.

Telecommunications Relay Support of the Mars Phoenix Lander Mission

Science.gov (United States)

Edwards, Charles D., Jr.; Erickson, James K.; Gladden, Roy E.; Guinn, Joseph R.; Ilott, Peter A.; Jai, Benhan; Johnston, Martin D.; Kornfeld, Richard P.; Martin-Mur, Tomas J.; McSmith, Gaylon W.;

Final Report for Crucible -Scale Radioactive Vitrification and Product Test of Waste Envelope B (AZ-102) Low-Activity Waste Glass

International Nuclear Information System (INIS)

CRAWFORD, CHARLES

2004-01-01

A proof-of-technology demonstration for the Hanford River Protection Project (RPP) Waste treatment and Immobilization Plant (WTP) was performed by the Savannah River Technology Center (SRTC). As part of this demonstration, treated AZ-102 Low-Activity Waste supernate was vitrified using a crucible-scale furnace. Initial glass samples were quench-cooled and characterized for metals and radionuclides. The glass was also durability tested using the American Society for Testing and Materials (ASTM) Product Consistency Test (PCT) protocol. These tests used the AZ-102 glass formulation Low Activity Waste (LAW) B88 that targeted AZ-102 waste loading at 5 wt% Na2O. After these initial results were obtained with the quench-cooled LAWB88 glass, a prototypical container centerline cooling (CCC) program was supplied to SRTC by WTP. A portion of the quench-cooled LAWB88 glass was remelted and centerline cooled. Samples from the CCC low-activity AZ-102 glass waste form were durability tested using the PCT and characterized for crystalline phase identification.This final report documents the characterization and durability of this AZ-102 glass

Formation and mechanism of nanocrystalline AZ91 powders during HDDR processing

Energy Technology Data Exchange (ETDEWEB)

Liu, Yafen; Fan, Jianfeng, E-mail: fanjianfeng@tyut.edu.cn; Zhang, Hua; Zhang, Qiang; Gao, Jing; Dong, Hongbiao, E-mail: hd38@leicester.ac.uk; Xu, Bingshe

2017-03-15

Grain sizes of AZ91 alloy powders were markedly refined to about 15 nm from 100 to 160 μm by an optimized hydrogenation-disproportionation-desorption-recombination (HDDR) process. The effect of temperature, hydrogen pressure and processing time on phase and microstructure evolution of AZ91 alloy powders during HDDR process was investigated systematically by X-ray diffraction, optical microscopy, scanning electron microscopy and transmission electron microscopy, respectively. The optimal HDDR process for preparing nanocrystalline Mg alloy powders is hydriding at temperature of 350 °C under 4 MPa hydrogen pressure for 12 h and dehydriding at 350 °C for 3 h in vacuum. A modified unreacted core model was introduced to describe the mechanism of grain refinement of during HDDR process. - Highlights: • Grain size of the AZ91 alloy powders was significantly refined from 100 μm to 15 nm. • The optimal HDDR technology for nano Mg alloy powders is obtained. • A modified unreacted core model of grain refinement mechanism was proposed.

Efficacy of Phoenix dactylifera L. (Date Palm Creams on Healthy Skin

Directory of Open Access Journals (Sweden)

Sidra Meer

2017-05-01

Full Text Available The date palm fruit (Phoenix dactylifera L. Arecaceae is used in most of the countries of the world and is an essential part of the diet, especially in many Arabian countries. Phoenix dactylifera L. fruits are a rich source of sugars (glucose and fructose, vitamins (A, C, and B complex, fibers, minerals, and phenolic compounds having antioxidant and anti-inflammatory properties. This study is designed to explore the Phoenix dactylifera L. fruit for skin care. A single-blinded, placebo control trial was conducted, including 11 healthy female volunteers after their informed consent. The efficacy of the Phoenix dactylifera L. extract (4% was evaluated in cream form after one, two, three, four, six, and eight weeks of treatment compared with the baseline. Prior to the study, the composition of the extract was analyzed to understand the underlying mechanisms by which the extract affects skin. Treating facial skin with the Phoenix dactylifera L. extract significantly improved all parameters investigated, such as skin elasticity, pigmentation, redness, brightness, and hydration and led to the improvement of the facial skin. There were no adverse reactions noted during the course of the patch test, demonstrating that the extract could be safe to apply on the skin. The Phoenix dactylifera L. fruit extract serves as a skin care ingredient that significantly improves characteristics important for perception of skin ageing and health. The efficacy of the treatment is possibly due to a combination of numerous active substances found in the Phoenix dactylifera L. extract.

Phoenix I energy extraction experiment

International Nuclear Information System (INIS)

Hoffman, J.M.; Patterson, E.L.; Tisone, G.C.; Moreno, J.B.

1980-07-01

Energy extraction experiments are reported for the Phoenix I amplifier driven by a discharge-initiated oscillator-preamplifier system operating on mixtures of either SF 6 -HI or SF 6 -C 2 H 6 and an electron-beam-initiated intermediate amplifer (lambda-3) fueled with H 2 and F 2 mixtures. When the oscillator-preamplifier system operated with mixtures of SF 6 -HI the input spectrum to the Phoenix I amplifier contained approx. 28 P-branch vibrational-rotational lines which were almost identical to the input spectrum from the H 2 -F 2 fueled oscillator. In this case the energy extraction measurements were essentially the same as the results obtained with the spectrum produced using H 2 and F 2 mixtures. For an input intensity of 10 7 W/cm 2 , 170 J were extracted from the amplifier. With the SF 6 -C 2 H 6 spectrum, extraction was only obtained from the first three excited vibrational levels. This result indicates that most of the energy in the amplifier could be extracted on the first three excited vibrational levels. It is shown that the extraction results can be fit with a simple two level model. The radius of curvature of the beam was estimated using a lateral shearing interferometer. It was found that the Phoenix I amplifier altered the radius of curvature

Implementation of a quality management system at the PHOENIX facility (CryoMaK)

International Nuclear Information System (INIS)

Urbach, Elisabeth; Bagrets, Nadezda; Weiss, Klaus-Peter

2013-01-01

Within a variety of mechanical tests in the Cryogenic Material Test Facility Karlsruhe (CryoMaK) at Karlsruhe Institute of Technology (KIT) the PHOENIX facility was prepared for multiple standard tensile tests in liquid helium, liquid nitrogen and at room temperature. With the multiple specimens holder 10 specimens can be tested within one cool down one after another. A quality management system is needed for ensuring reproducible preconditions. For the guarantee of the competence of the laboratory and the measurement equipment, a quality management system was implemented and prepared for accreditation according to DIN EN ISO/IEC 17025 (ISO 17025). The implementation of a quality management system allows high precision test results included the estimation of measurement uncertainty. This paper gives an overview of the management and technical requirements for the accreditation of the PHOENIX testing facility

Implementation of a quality management system at the PHOENIX facility (CryoMaK)

Energy Technology Data Exchange (ETDEWEB)

Urbach, Elisabeth, E-mail: elisabeth.urbach@kit.edu; Bagrets, Nadezda; Weiss, Klaus-Peter

2013-10-15

Within a variety of mechanical tests in the Cryogenic Material Test Facility Karlsruhe (CryoMaK) at Karlsruhe Institute of Technology (KIT) the PHOENIX facility was prepared for multiple standard tensile tests in liquid helium, liquid nitrogen and at room temperature. With the multiple specimens holder 10 specimens can be tested within one cool down one after another. A quality management system is needed for ensuring reproducible preconditions. For the guarantee of the competence of the laboratory and the measurement equipment, a quality management system was implemented and prepared for accreditation according to DIN EN ISO/IEC 17025 (ISO 17025). The implementation of a quality management system allows high precision test results included the estimation of measurement uncertainty. This paper gives an overview of the management and technical requirements for the accreditation of the PHOENIX testing facility.

Superfund Record of Decision (EPA Region 9): Nineteenth Avenue Landfill, Phoenix, AZ. (First remedial action), September 1989. Final report

International Nuclear Information System (INIS)

1989-01-01

The 213-acre Nineteenth Avenue Landfill is in an industrial area of Maricopa County, Phoenix, Arizona. State permitted landfill operations were conducted from 1957 to 1979 during which time approximately nine million cubic yards of municipal refuse, solid and liquid industrial wastes, and some medical wastes and materials containing low levels of radioactivity were deposited in the landfill. The State ordered the landfill closed in 1979 due to the periodic inundation of the landfill by flood waters from the Salt River Channel. Subsequently, the city covered the site with fill, stockpiled soil for final capping, installed ground water monitoring wells, built berms around the landfill, and installed a methane gas collection system. The remedial action is designed to mitigate threats resulting from flooding of the landfill, which has occurred intermittently since 1965. The primary contaminants of concern in the soil/refuse include VOCs such as toluene and xylenes

Digibaro pressure instrument onboard the Phoenix Lander

Science.gov (United States)

Harri, A.-M.; Polkko, J.; Kahanpää, H. H.; Schmidt, W.; Genzer, M. M.; Haukka, H.; Savijarv1, H.; Kauhanen, J.

2009-04-01

The Phoenix Lander landed successfully on the Martian northern polar region. The mission is part of the National Aeronautics and Space Administration's (NASA's) Scout program. Pressure observations onboard the Phoenix lander were performed by an FMI (Finnish Meteorological Institute) instrument, based on a silicon diaphragm sensor head manufactured by Vaisala Inc., combined with MDA data processing electronics. The pressure instrument performed successfully throughout the Phoenix mission. The pressure instrument had 3 pressure sensor heads. One of these was the primary sensor head and the other two were used for monitoring the condition of the primary sensor head during the mission. During the mission the primary sensor was read with a sampling interval of 2 s and the other two were read less frequently as a check of instrument health. The pressure sensor system had a real-time data-processing and calibration algorithm that allowed the removal of temperature dependent calibration effects. In the same manner as the temperature sensor, a total of 256 data records (8.53 min) were buffered and they could either be stored at full resolution, or processed to provide mean, standard deviation, maximum and minimum values for storage on the Phoenix Lander's Meteorological (MET) unit.The time constant was approximately 3s due to locational constraints and dust filtering requirements. Using algorithms compensating for the time constant effect the temporal resolution was good enough to detect pressure drops associated with the passage of nearby dust devils.

Power lines Phoenix and the making of the modern southwest

CERN Document Server

Needham, Andrew

2014-01-01

In 1940, Phoenix was a small, agricultural city of sixty-five thousand, and the Navajo Reservation was an open landscape of scattered sheepherders. Forty years later, Phoenix had blossomed into a metropolis of 1.5 million people and the territory of the Navajo Nation was home to two of the largest strip mines in the world. Five coal-burning power plants surrounded the reservation, generating electricity for export to Phoenix, Los Angeles, and other cities. Exploring the postwar developments of these two very different landscapes, Power Lines tells the story of the far-reaching environmental a

75 FR 78976 - Procurement List Proposed Addition and Deletions

Science.gov (United States)

2010-12-17

... NSN: 7510-01-555-6167--Inkjet printer cartridge NPA: Alabama Industries for the Blind, Talladega, AL.../Location: Eyewear Prescription Service, Phoenix Indian Medical Center, 4212 N. 16th Street, Phoenix, AZ. NPA: Winston-Salem Industries for the Blind, Winston-Salem, NC. Contracting Activity: Health and Human...

Start-up physics test predictions for Indian Point 3, cycle 7, utilized PHOENIX-P/ANC

International Nuclear Information System (INIS)

Powers, M.A.; Buechel, R.J.

1989-01-01

The Westinghouse Advanced In-Core Fuel Management System (PHOENIX-P/ANC) was utilized to predict start-up physics test parameters for Indian Point 3 (IP3) cycle 7. This core utilizes a low-leakage loading pattern implementing VANTAGE-5 fuel, which incorporates axial blankets and integral fuel burnable absorbers. Discrete part-length wet annular burnable absorbers (WABAs) are used in some feed assemblies as well. As a measure to reduce vessel fluence, certain peripheral twice-burned assemblies also contain fresh full-length WABAs. The New York Power Authority (NYPA) is using the Westinghouse code system since the methodology was licensed by the U.S. Nuclear Regulatory Commission and because of the user support supplied by Westinghouse. The IP3 cycle 7 PHOENIX-P/ANC model was developed as a joint effort by NYPA and Westinghouse as part of a technology transfer agreement. The PHOENIX-P/ANC model performed very well in start-up physics test predictions and is expected to agree well through cycle depletion. These results have given NYPA further incentive to use the Westinghouse methodology for core follow, loading pattern design determination, and in the safety analysis area

Assessing Habitability: Lessons from the Phoenix Mission

Science.gov (United States)

Stoker, Carol R.

2013-01-01

The Phoenix mission's key objective was to search for a habitable zone. The Phoenix lander carried a robotic arm with digging scoop to collect soil and icy material for analysis with an instrument payload that included volatile mineral and organic analysis(3) and soil ionic chemistry analysis (4). Results from Phoenix along with theoretical modeling and other previous mission results were used to evaluate the habitability of the landing site by considering four factors that characterize the environments ability to support life as we know it: the presence of liquid water, the presence of an energy source to support metabolism, the presence of nutrients containing the fundamental building blocks of life, and the absence of environmental conditions that are toxic to or preclude life. Phoenix observational evidence for the presence of liquid water (past or present) includes clean segregated ice, chemical etching of soil grains, calcite minerals in the soil and variable concentrations of soluble salts5. The maximum surface temperature measured was 260K so unfrozen water can form only in adsorbed films or saline brines but warmer climates occur cyclically on geologically short time scales due to variations in orbital parameters. During high obliquity periods, temperatures allowing metabolism extend nearly a meter into the subsurface. Phoenix discovered 1%w/w perchlorate salt in the soil, a chemical energy source utilized by a wide range of microbes. Nutrient sources including C, H, N, O, P and S compounds are supplied by known atmospheric sources or global dust. Environmental conditions are within growth tolerance for terrestrial microbes. Summer daytime temperatures are sufficient for metabolic activity, the pH is 7.8 and is well buffered and the projected water activity of a wet soil will allow growth. In summary, martian permafrost in the north polar region is a viable location for modern life. Stoker et al. presented a formalism for comparing the habitability of

Digging Movie from Phoenix's Sol 18

Science.gov (United States)

2008-01-01

The Surface Stereo Imager on NASA's Phoenix Mars Lander recorded the images combined into this movie of the lander's Robotic Arm enlarging and combining the two trenches informally named 'Dodo' (left) and 'Goldilocks.' The 21 images in this sequence were taken over a period of about 2 hours during Phoenix's Sol 18 (June 13, 2008), or the 18th Martian day since landing. The main purpose of the Sol 18 dig was to dig deeper for learning the depth of a hard underlying layer. A bright layer, possibly ice, was increasingly exposed as the digging progressed. Further digging and scraping in the combined Dodo-Goldilocks trench was planned for subsequent sols. The combined trench is about 20 centimeters (about 8 inches) wide. The depth at the end of the Sol 18 digging is 5 to 6 centimeters (about 2 inches). The Goldilocks trench was the source of soil samples 'Baby Bear' and 'Mama Bear,' which were collected on earlier sols and delivered to instruments on the lander deck. The Dodo trench was originally dug for practice in collecting and depositing soil samples. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

Characterization of mussel H2A.Z.2: a new H2A.Z variant preferentially expressed in germinal tissues from Mytilus.

Science.gov (United States)

Rivera-Casas, Ciro; González-Romero, Rodrigo; Vizoso-Vazquez, Ángel; Cheema, Manjinder S; Cerdán, M Esperanza; Méndez, Josefina; Ausió, Juan; Eirin-Lopez, Jose M

2016-10-01

Histones are the fundamental constituents of the eukaryotic chromatin, facilitating the physical organization of DNA in chromosomes and participating in the regulation of its metabolism. The H2A family displays the largest number of variants among core histones, including the renowned H2A.X, macroH2A, H2A.B (Bbd), and H2A.Z. This latter variant is especially interesting because of its regulatory role and its differentiation into 2 functionally divergent variants (H2A.Z.1 and H2A.Z.2), further specializing the structure and function of vertebrate chromatin. In the present work we describe, for the first time, the presence of a second H2A.Z variant (H2A.Z.2) in the genome of a non-vertebrate animal, the mussel Mytilus. The molecular and evolutionary characterization of mussel H2A.Z.1 and H2A.Z.2 histones is consistent with their functional specialization, supported on sequence divergence at promoter and coding regions as well as on varying gene expression patterns. More precisely, the expression of H2A.Z.2 transcripts in gonadal tissue and its potential upregulation in response to genotoxic stress might be mirroring the specialization of this variant in DNA repair. Overall, the findings presented in this work complement recent reports describing the widespread presence of other histone variants across eukaryotes, supporting an ancestral origin and conserved role for histone variants in chromatin.

76 FR 72722 - Certain Projectors With Controlled-Angle Optical Retarders, Components Thereof, and Products...

Science.gov (United States)

2011-11-25

... served: Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan 108-0075; Sony Corporation of America, 550... Kingdom and Compound Photonics U.S. Corporation of Phoenix, Arizona. A supplement to the Complaint was... Photonics U.S. Corporation, 1110 North 52nd Street, Phoenix, AZ 85008. (b) The respondents are the following...

Animated Optical Microscope Zoom in from Phoenix Launch to Martian Surface

Science.gov (United States)

2008-01-01

[figure removed for brevity, see original site] Click on image for animation This animated camera view zooms in from NASA's Phoenix Mars Lander launch site all the way to Phoenix's Microscopy and Electrochemistry and C Eonductivity Analyzer (MECA) aboard the spacecraft on the Martian surface. The final frame shows the soil sample delivered to MECA as viewed through the Optical Microscope (OM) on Sol 17 (June 11, 2008), or the 17th Martian day. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

Development of AZS refractories for the glass industry

International Nuclear Information System (INIS)

Guzman, A.M.; Rodriguez, P.

2004-01-01

Refractory materials can support high temperatures, thermal strength and the contact with aggressive environments, for this reason they are widely used in the cement, glass and steel industry. Commercial AZS (alumina-zirconia-silica) refractories are a good alternative in refractory materials for the glass industry' because they can support the aggressive conditions during liquid processing of glass. However, another problem encountered in glass industry is contamination by refractory' material that fall into the molten glass, which can produce a series of defects in the final product. This research was conducted to develop new formulations of AZS refractories with different amounts of ZrO 2 with the purpose of improving the characteristics, properties and the work conditions in the glass melting furnaces and, at the same time, lower the costs this type of refractories. The results obtained indicate that the composition with low content of ZrO 2 can provide better properties than the commercial product, with some modifications in the particle size distribution. Copyright (2004) AD-TECH - International Foundation for the Advancement of Technology Ltd

75 FR 17692 - Foreign-Trade Zone 75 -- Phoenix, Arizona, Application for Reorganization under Alternative Site...

Science.gov (United States)

2010-04-07

...'' in the context of the Board's standard 2,000-acre activation limit for a general-purpose zone project... terminal at the Phoenix Sky Harbor International Airport, Phoenix; Site 2 (18 acres) CC&F South Valley..., 4747 West Buckeye Road, Phoenix; Site 4 (18 acres) - Santa Fe Business Park, 47th Avenue and Campbell...

Corrosion product layers on magnesium alloys AZ31 and AZ61: Surface chemistry and protective ability

Science.gov (United States)

Feliu, S.; Llorente, I.

2015-08-01

This paper studies the chemical composition of the corrosion product layers formed on magnesium alloys AZ31 and AZ61 following immersion in 0.6 M NaCl, with a view to better understanding their protective action. Relative differences in the chemical nature of the layers were quantified by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDX) and low-angle X-ray diffraction (XRD). Corrosion behavior was investigated by Electrochemical Impedance Spectroscopy (EIS) and hydrogen evolution measurement. An inhibitive effect from the corrosion product layers was observed from EIS, principally in the case of AZ31, as confirmed by hydrogen evolution tests. A link was found between carbonate enrichment observed by XPS in the surface of the corrosion product layer, concomitant with the increase in the protective properties observed by EIS.

Update of PHOENIX-P 42 group library from CENDL-2

International Nuclear Information System (INIS)

Zhang Baocheng

1998-01-01

PHOENIX-P is a lattice physics code system, developed by the Westinghouse Electric Corporation (WEC), which was transplanted and used at Dayabay Nuclear Power Plant (DNPJVC). The associated multi-group (42-group) library was derived from the evaluated nuclear data of ENDF/B-5. Since the original library is from the old evaluated nuclear data, it can not meet all the requirements of reactor physics calculations of the nuclear power plant. So it is necessary to update the library with the latest version of evaluated nuclear data. To do so, based on the investigation of the old library and the information about the library, some programs were developed at China Nuclear Data Center (CNDC) to produce PHOENIX-P format data sets mainly from CENDL-2 and the new data were used to supersede the old ones of the PHOENIX-P library

Animation of Panorama of Phoenix's Solar Panel and Robotic Arm

Science.gov (United States)

2008-01-01

[figure removed for brevity, see original site] Click on image for animation This is an animation of panorama images of NASA's Phoenix Mars Lander's solar panel and the lander's Robotic Arm with a sample in the scoop. The image was taken just before the sample was delivered to the Optical Microscope. The images making up this animation were taken by the lander's Surface Stereo Imager looking west during Phoenix's Sol 16 (June 10, 2008), or the 16th Martian day after landing. This view is a part of the 'mission success' panorama that will show the whole landing site in color. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

Pyrolysis Characteristics and Kinetics of Phoenix Tree Residues as a Potential Energy

Directory of Open Access Journals (Sweden)

H. Li

2015-09-01

Full Text Available By using a thermogravimetric analyser under argon atmosphere, the pyrolysis process and the kinetic model of phoenix tree residues (the little stem, middle stem, and leaf at a 30 °C min−1 heating rate and the phoenix tree mix at three different heating rates (10 °C min−1, 30 °C min−1, and 50 °C min−1 were examined. The catalyst and the co-pyrolysis samples were at a 30 °C min−1 heating rate. The catalysts were Na2CO3, ZnCl2 and CaO in a mass fraction of 5 %. The experimental results revealed that the phoenix tree residues pyrolysis process consisted of three stages: dehydration stage, main pyrolysis stage, and the slow decomposition of residues. As the heating rate increased, the pyrolysis characteristic temperature of the phoenix tree grew, there was a backward-shift of the pyrolysis rate curve, and the mass loss rate gradually increased. The phoenix tree residues’ activation energy changed throughout the whole pyrolysis process, and the pyrolysis temperature ranges of the three main components (cellulose, hemicellulose, and lignin existed in overlapping phenomenon. As compared to the little stem, middle stem, and leaf, the phoenix tree mix was more likely to be pyrolysed under the same heating rate. Different catalysts had a different impact on the pyrolysis: ZnCl2 moved the start point of the reaction to the lower temperatures, but did not speed up the reaction; Na2CO3 speeded up the reaction without changing the start point of the reaction; CaO speeded up the reaction, moved the start point of the reaction to higher temperatures.

77 FR 10649 - Modification of Class E Airspace; Douglas, AZ

Science.gov (United States)

2012-02-23

...-1313; Airspace Docket No. 11-AWP-17] Modification of Class E Airspace; Douglas, AZ AGENCY: Federal... Bisbee Douglas International Airport, Douglas, AZ. Decommissioning of the Cochise VHF Omni-Directional... Federal Register a notice of proposed rulemaking to amend controlled airspace at Douglas, AZ (76 FR 78180...

Manufacturing and Design Engineering Students St. Mary's Hospital, Phoenix Park.

OpenAIRE

Mitchell, Leah

2012-01-01

Poster with details of project to improve ease of movement for Kirton Stirling chairs in St. Mary's Hospital, Phoenix Park, Dublin. Third year students in the B Eng (Honours) Manufacturing and Design Engineering course at Bolton St. completed a project in conjunction with St. Mary‟s Hospital, Phoenix Park. The staff in St Mary‟s were experiencing difficulty in moving the Kirton Stirling chairs (pictured above). These chairs are used to transport elderly patients from one location to another. ...

Dinosaur or Phoenix: Nuclear Bombers in the 21st Century

Science.gov (United States)

2010-04-12

REPORT DATE 02-04-10 2. REPORT TYPE Master’s Thesis 3. DATES COVERED 31-07-09 to 16-06-10 4. TITLE AND SUBTITLE Dinosaur or Phoenix: Nuclear...WARFIGHTING SCHOOL DINOSAUR OR PHOENIX: NUCLEAR BOMBERS IN THE 21ST CENTURY by John W. Morehead Colonel, United States Air Force A paper...can argue Secretary Gates’ decision to halt development of a follow-on bomber indicates the DOD views nuclear bombers as dinosaurs no longer needed as

Hydro mechanical deep-drawing and high pressure sheet metal forming as forming technologies for the production of complex parts made of magnesium sheet metal AZ31B-0; Hydromechanisches Tiefziehen und Hochdruckblechumformung als Verfahren zur Herstellung komplexer Bauteile aus Magnesiumfeinblechen des Typs AZ31B-0

Energy Technology Data Exchange (ETDEWEB)

Viehweger, B.; Richter, G.; Duering, M.; Karabet, A. [Lehrstuhlleiter, BTU Cottbus, Lehrstuhl Konstruktion und Fertigung, Konrad-Wachsmann Allee 1, 03046 Cottbus (Germany); Sviridov, A.; Hartmann, H.; Richter, U. [Forschungs- und Qualitaetszentrum Oderbruecke gGmbH Eisenhuettenstadt (Germany)

2004-07-01

Semi - finished sheet - metal products made of magnesium alloys such as AZ31B are known as better deformable at temperatures in the range of 175 C - 240 C. By means of hydroforming technologies, as there are hydro mechanical deep-drawing and high pressure sheet metal forming, the influence of different forming parameters on the forming results has been investigated. A more complex experimental geometry was deformed applying forming temperatures of 175 C, 200 C, 225 C and 240 C and accordingly adjusted forces of the blank holder. Concerning the applied forming - methods and experimental parameters the forming results have been evaluated and compared regarding the decrease of sheet thickness and the development of small radii. For some experimental parts, which have been deformed by means of high pressure sheet metal forming at temperatures of 175 C and 225 C, supplementary investigations have been carried out in order to determine the evolution of characteristic surface values in dependence on the forming operation. On the basis of these results practical recommendations for the limits of application of aforementioned forming technologies for AZ31B-0 magnesium sheet metal are given. (Abstract Copyright [2004], Wiley Periodicals, Inc.) [German] Eine gute Umformbarkeit von Blechhalbzeugen aus Magnesiumknetlegierungen stellt sich bekanntlich bei Anwendung von Umformtemperaturen im Bereich von 175 C - 240 C ein. Anhand der wirkmedienbasierten Umformverfahren hydromechanisches Tiefziehen und Hochdruckblechumformung ist an handelsueblichen AZ31B-0 Feinblechen die Einstellung unterschiedlicher Umformparameter erprobt worden. Unter Verwendung von Umformtemperaturen von 175 C, 200 C, 225 C und 240 C und entsprechend angepassten Niederhalterdruecken ist eine praxisnahe Versuchsgeometrie ''Minihood'' ausgeformt worden. Im Hinblick auf angewendete Umformverfahren und Versuchsparameter wurde an den Versuchsbauteilen die Blechdickenabnahme und die

The chloroplast DNA locus psbZ-trnfM as a potential barcode marker in Phoenix L. (Arecaceae

Directory of Open Access Journals (Sweden)

Marco Ballardini

2013-12-01

Full Text Available The genus Phoenix (Arecaceae comprises 14 species distributed from Cape Verde Islands to SE Asia. It includes the economically important species Phoenix dactylifera. The paucity of differential morphological and anatomical useful characters, and interspecific hybridization, make identification of Phoenix species difficult. In this context, the development of reliable DNA markers for species and hybrid identification would be of great utility. Previous studies identified a 12 bp polymorphic chloroplast minisatellite in the trnG(GCC-trnfM(CAU spacer, and showed its potential for species identification in Phoenix. In this work, in order to develop an efficient DNA barcode marker for Phoenix, a longer cpDNA region (700 bp comprising the mentioned minisatellite, and located between the psbZ and trnfM(CAU genes, was sequenced. One hundred and thirty-six individuals, representing all Phoenix species except P. andamanensis, were analysed. The minisatellite showed 2-7 repetitions of the 12 bp motif, with 1-3 out of seven haplotypes per species. Phoenix reclinata and P. canariensis had species-specific haplotypes. Additional polymorphisms were found in the flanking regions of the minisatellite, including substitutions, indels and homopolymers. All this information allowed us to identify unambiguously eight out of the 13 species, and overall 80% of the individuals sampled. Phoenix rupicola and P. theophrasti had the same haplotype, and so had P. atlantica, P. dactylifera, and P. sylvestris (the “date palm complex” sensu Pintaud et al. 2013. For these species, additional molecular markers will be required for their unambiguous identification. The psbZ-trnfM(CAU region therefore could be considered as a good basis for the establishment of a DNA barcoding system in Phoenix, and is potentially useful for the identification of the female parent in Phoenix hybrids.

Winds at the Phoenix landing site

DEFF Research Database (Denmark)

Holstein-Rathlou, C.; Gunnlaugsson, H.P.; Merrison, J.P.

2010-01-01

Wind speeds and directions were measured on the Phoenix Lander by a mechanical anemometer, the so-called Telltale wind indicator. Analysis of images of the instrument taken with the onboard imager allowed for evaluation of wind speeds and directions. Daily characteristics of the wind data are hig...

Tank 241-AZ-101 tank characterization plan

International Nuclear Information System (INIS)

Schreiber, R.D.

1995-01-01

The Defense Nuclear Facilities Safety Board has advised the DOE to concentrate the near-term sampling and analysis activities on identification and resolution of safety issues. The Data Quality Objective (DQO) process was chosen as a tool to be used in the resolution of safety issues. As a result, A revision in the Federal Facilities Agreement and Consent Order (Tri-Party Agreement) milestone M-44 has been made, which states that ''A Tank Characterization Plan (TCP) will also be developed for each double-shell tank (DST) and single-shell tank (SST) using the DQO process. Development of TCPs by the DQO process is intended to allow users to ensure their needs will be met and that resources are devoted to gaining only necessary information''. This document satisfies that requirement for Tank 241-AZ-101 (AZ-101) sampling activities. Tank AZ-101 is currently a non-Watch List tank, so the only DQOs applicable to this tank are the safety screening DQO and the compatibility DQO, as described below. The contents of Tank AZ-101, as of October 31, 1994, consisted of 3,630 kL (960 kgal) of dilute non-complexed waste and aging waste from PUREX (NCAW, neutralized current acid waste). Tank AZ-101 is expected to have two primary layers. The bottom layer is composed of 132 kL of sludge, and the top layer is composed of 3,500 kL of supernatant, with a total tank waste depth of approximately 8.87 meters

Patient deaths blamed on long waits at the Phoenix VA

Directory of Open Access Journals (Sweden)

Robbins RA

2014-04-01

Full Text Available No abstract available. Article truncated at 150 words. This morning the lead article in the Arizona Republic was a report blaming as many as 40 deaths at the Phoenix VA on long waits (1. Yesterday, Rep. Jeff Miller, the chairman of the House Committee on Veterans Affairs, held a hearing titled “A Continued Assessment of Delays in VA Medical Care and Preventable Veteran Deaths.” “It appears as though there could be as many as 40 veterans whose deaths could be related to delays in care,” Miller announced to a stunned audience. The committee has spent months investigating patient-care scandals and allegations at VA facilities in Pittsburgh, Atlanta, Miami and other cities. said that dozens of VA hospital patients in Phoenix may have died while awaiting medical care. He went on to say that staff investigators have evidence that the Phoenix VA Health Care System keeps two sets of records to conceal prolonged waits that patients must endure for ...

User Manual for the AZ-101 Data Acquisition System (AS-101 DAS)

Energy Technology Data Exchange (ETDEWEB)

BRAYTON, D.D.

2000-02-17

User manual for the TK AZ-101 Waste Retrieval System Data Acquisition System. The purpose of this document is to describe use of the AZ-101 Data Acquisition System (AZ-101 DAS). The AZ-101 DAS is provided to fulfill the requirements for data collection and monitoring as defined in Letters of Instruction (LOI) from Numatec Hanford Corporation (NHC) to Fluor Federal Services (FFS). For a complete description of the system, including design, please refer to the AZ-101 DAS System Description document, RPP-5572.

User Manual for the AZ-101 Data Acquisition System (AS-101 DAS)

International Nuclear Information System (INIS)

BRAYTON, D.D.

2000-01-01

User manual for the TK AZ-101 Waste Retrieval System Data Acquisition System. The purpose of this document is to describe use of the AZ-101 Data Acquisition System (AZ-101 DAS). The AZ-101 DAS is provided to fulfill the requirements for data collection and monitoring as defined in Letters of Instruction (LOI) from Numatec Hanford Corporation (NHC) to Fluor Federal Services (FFS). For a complete description of the system, including design, please refer to the AZ-101 DAS System Description document, RPP-5572

76 FR 78180 - Proposed Modification of Class E Airspace; Douglas, AZ

Science.gov (United States)

2011-12-16

...-1313; Airspace Docket No. 11-AWP-17] Proposed Modification of Class E Airspace; Douglas, AZ AGENCY... action proposes to modify Class E airspace at Bisbee Douglas International Airport, Douglas, AZ... feet above the surface at Douglas, AZ. Additional controlled airspace is necessary to accommodate...

Histone H2A.Z is essential for estrogen receptor signaling

Science.gov (United States)

Gévry, Nicolas; Hardy, Sara; Jacques, Pierre-Étienne; Laflamme, Liette; Svotelis, Amy; Robert, François; Gaudreau, Luc

2009-01-01

Incorporation of H2A.Z into the chromatin of inactive promoters has been shown to poise genes for their expression. Here we provide strong evidence that H2A.Z is incorporated into the promoter regions of estrogen receptor (ERα) target genes only upon gene induction, and that, in a cyclic pattern. Moreover, members of the human H2A.Z-depositing complex, p400, also follow the same gene recruitment kinetics as H2A.Z. Importantly, cellular depletion of H2A.Z or p400 leads to a severe defect in estrogen signaling, including loss of estrogen-specific cell proliferation. We find that incorporation of H2A.Z within TFF1 promoter chromatin allows nucleosomes to adopt preferential positions along the DNA translational axis. Finally, we provide evidence that H2A.Z is essential to allow estrogen-responsive enhancer function. Taken together, our results provide strong mechanistic insight into how H2A.Z regulates ERα-mediated gene expression and provide a novel link between H2A.Z–p400 and ERα-dependent gene regulation and enhancer function. PMID:19515975

Tank 241-AZ-102 tank characterization plan

International Nuclear Information System (INIS)

Schreiber, R.D.

1995-01-01

The Defense Nuclear Facilities Safety Board has advised the DOE to concentrate the near-term sampling and analysis activities on identification and resolution of safety issues. The Data Quality Objective (DQO) process was chosen as a tool to be used in the resolution of safety issues. As a result, a revision in the Federal Facilities Agreement and Consent Order (Tri-Party Agreement) milestone M-44 has been made, which states that ''A Tank Characterization Plan (TCP) will also be developed for each double-shell tank (DST) and single-shell tank (SST) using the DQO process ... Development of TCPs by the DQO process is intended to allow users to ensure their needs will be met and that resources are devoted to gaining only necessary information''. This document satisfies that requirement for tank 241-AZ-102 (AZ-102) sampling activities. Tank AZ-102 is currently a non-Watch List tank, so the only DQOs applicable to this tank are the safety screening DQO and the compatibility DQO, as described below. The current contents of Tank AZ-102, as of October 31, 1994, consisted of 3,600 kL (950 kgal) of dilute non-complexed waste and aging waste from PUREX (NCAW, neutralized current acid waste). Tank AZ-102 is expected to have two primary layers. The bottom layer is composed of 360 kL of sludge, and the top layer is composed of 3,240 kL of supernatant, with a total tank waste depth of approximately 8.9 meters

Solar Panel Buffeted by Wind at Phoenix Site

Science.gov (United States)

2008-01-01

Winds were strong enough to cause about a half a centimeter (.19 inch) of motion of a solar panel on NASA's Phoenix Mars lander when the lander's Surface Stereo Imager took this picture on Aug. 31, 2008, during the 96th Martian day since landing. The lander's telltale wind gauge has been indicating wind speeds of about 4 meters per second (9 miles per hour) during late mornings at the site. These conditions were anticipated and the wind is not expected to do any harm to the lander. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

Influence of the Composition of the Hank’s Balanced Salt Solution on the Corrosion Behavior of AZ31 and AZ61 Magnesium Alloys

Directory of Open Access Journals (Sweden)

Jakub Tkacz

2017-11-01

Full Text Available The electrochemical corrosion characteristics of AZ31 and AZ61 magnesium alloys were analyzed in terms of potentiodynamic tests and electrochemical impedance spectroscopy. The influence of the solution composition and material surface finish was examined also through the analysis of corrosion products created on the samples’ surface after electrochemical measurements in terms of scanning electron microscopy using energy-dispersive spectroscopy. Obtained data revealed the differences in the response of the magnesium alloys to enriched Hank’s Balanced Salt Solution—HBSS+ (with Mg2+ and Ca2+ ions and Hank’s Balanced Salt Solution—HBSS (without Mg2+ and Ca2+ ions. Both examined alloys exhibited better corrosion resistance from the thermodynamic and kinetic point of view in the enriched HBSS+. AZ61 magnesium alloy reached higher values of polarization resistance than AZ31 magnesium alloy in both the used corrosion solutions. Phosphate-based corrosion products were characteristic for the AZ31 and AZ61 alloys tested in the HBSS (without Mg2+ and Ca2+ ions. The combination of phosphate-based corrosion products and clusters of MgO and Mg(OH2 was typical for the surface of samples tested in the enriched HBSS+ (with Mg2+ and Ca2+ ions. Pitting corrosion attack was observed only in the case of enriched HBSS+.

Electrochemical corrosion behavior of AZ91D alloy in ethylene glycol

International Nuclear Information System (INIS)

Fekry, A.M.; Fatayerji, M.Z.

2009-01-01

The effect of concentration on the corrosion behavior of Mg-based alloy AZ91D was investigated in ethylene glycol-water solutions using electrochemical techniques i.e. potentiodynamic polarization, electrochemical impedance measurements (EIS) and surface examination via scanning electron microscope (SEM) technique. This can provide a basis for developing new coolants for magnesium alloy engine blocks. Corrosion behavior of AZ91D alloy by coolant is important in the automotive industry. It was found that the corrosion rate of AZ91D alloy decreased with increasing concentration of ethylene glycol. For AZ91D alloy in chloride >0.05 M or fluoride 0.05 M for fluoride containing ethylene glycol solution, some inhibition effect has been observed. The corrosion of AZ91D alloy in the blank can be effectively inhibited by addition of 0.05 mM paracetamol that reacts with AZ91D alloy and forms a protective film on the surface at this concentration as confirmed by surface examination.

Dictionary of engines. The internal combustion engine from A-Z; Lexikon Motorentechnik. Der Verbrennungsmotor von A-Z

Energy Technology Data Exchange (ETDEWEB)

Schaefer, F. (ed.); Basshuysen, R. van

2004-04-01

This dictionary describes current engine technology and gives an outlook to the future. Cross-references, broader and narrower terms ensure optimal user guidance. Entries do not stand alone but provide content-oriented information. About 4,500 terms are included from A-Z, providing an outline of subjects like exhaust systems, acoustics, supercharging, combustion chamber, injection systems, control, flame propagation, mixing, catalytic converters, pistons, fuels, cooling, crank casing, stratified charging, lambda control, camshaft, oil, particulate filters, sensors/actuators, pollutants, valves, combustion processes, efficiency, ignition, cylinder head. The dictionary is for development engineers in the motor car industry, in component and system development in the supply industry, university teachers and students, foremen in motor car repair shops, etc. (orig.) [German] Das Lexikon Motorentechnik ist ein Nachschlagewerk, das die aktuelle Motorentechnik umfassend beschreibt und Ausblicke in der Zukunft ermoeglicht. Das ausgefeilte System aus Querverweisen fuehrt alle Unterbegriffe zum Hauptbegriff und ermoeglicht so eine optimale Benutzerfuehrung. Dadurch stehen die Stichwoerter nicht isoliert, sondern es werden inhaltlich zusammenhaengende Betrachtungen moeglich. Der Inhalt umfasst 4 500 Begriffe von A-Z wie z.B.: Abgastechnik, Akustik, Aufladung, Brennraum, Einspritzsysteme, Elektronische Motorsteuerung, Flammenausbreitung, Gemischbildung, Katalysator, Kolben, Kraftstoff, Kuehlung, Kurbelgehaeuse, Kurbeltrieb, Ladungswechsel, Lambda-Regelung, Nockenwelle, Oel, Partikelfilter, Sensoren/Aktuatoren, Schadstoffe, Ventiltrieb, Verbrennungsverfahren, Wirkungsgrad, Zuendung, Zylinderkopf. Die Zielgruppen waeren Ingenieure in Motoren- und Fahrzeugentwicklung der Automobilindustrie, Ingenieure in der Komponenten- und Systementwicklung der Zuliefererindustrie, Professoren und Studenten an Hochschulen mit Schwerpunkt Kraftfahrzeugtechnik, Meister in Kfz-Werkstaetten. (orig.)

Corrosion product layers on magnesium alloys AZ31 and AZ61: Surface chemistry and protective ability

Energy Technology Data Exchange (ETDEWEB)

Feliu, S., E-mail: sfeliu@cenim.csic.es; Llorente, I.

2015-08-30

Highlights: • Surface chemistry of the corrosion product layers on magnesium alloys. • Influence of the type of alloy on the carbonate surface enrichment. • Relation between surface composition and protection properties. - Abstract: This paper studies the chemical composition of the corrosion product layers formed on magnesium alloys AZ31 and AZ61 following immersion in 0.6 M NaCl, with a view to better understanding their protective action. Relative differences in the chemical nature of the layers were quantified by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDX) and low-angle X-ray diffraction (XRD). Corrosion behavior was investigated by Electrochemical Impedance Spectroscopy (EIS) and hydrogen evolution measurement. An inhibitive effect from the corrosion product layers was observed from EIS, principally in the case of AZ31, as confirmed by hydrogen evolution tests. A link was found between carbonate enrichment observed by XPS in the surface of the corrosion product layer, concomitant with the increase in the protective properties observed by EIS.

Corrosion product layers on magnesium alloys AZ31 and AZ61: Surface chemistry and protective ability

International Nuclear Information System (INIS)

Feliu, S.; Llorente, I.

2015-01-01

Highlights: • Surface chemistry of the corrosion product layers on magnesium alloys. • Influence of the type of alloy on the carbonate surface enrichment. • Relation between surface composition and protection properties. - Abstract: This paper studies the chemical composition of the corrosion product layers formed on magnesium alloys AZ31 and AZ61 following immersion in 0.6 M NaCl, with a view to better understanding their protective action. Relative differences in the chemical nature of the layers were quantified by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDX) and low-angle X-ray diffraction (XRD). Corrosion behavior was investigated by Electrochemical Impedance Spectroscopy (EIS) and hydrogen evolution measurement. An inhibitive effect from the corrosion product layers was observed from EIS, principally in the case of AZ31, as confirmed by hydrogen evolution tests. A link was found between carbonate enrichment observed by XPS in the surface of the corrosion product layer, concomitant with the increase in the protective properties observed by EIS

Phoenix Robotic Arm's Workspace After 90 Sols

Science.gov (United States)

2008-01-01

During the first 90 Martian days, or sols, after its May 25, 2008, landing on an arctic plain of Mars, NASA's Phoenix Mars Lander dug several trenches in the workspace reachable with the lander's robotic arm. The lander's Surface Stereo Imager camera recorded this view of the workspace on Sol 90, early afternoon local Mars time (overnight Aug. 25 to Aug. 26, 2008). The shadow of the the camera itself, atop its mast, is just left of the center of the image and roughly a third of a meter (one foot) wide. The workspace is on the north side of the lander. The trench just to the right of center is called 'Neverland.' The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

The Phoenix Mars Lander Robotic Arm

Science.gov (United States)

Bonitz, Robert; Shiraishi, Lori; Robinson, Matthew; Carsten, Joseph; Volpe, Richard; Trebi-Ollennu, Ashitey; Arvidson, Raymond E.; Chu, P. C.; Wilson, J. J.; Davis, K. R.

2009-01-01

The Phoenix Mars Lander Robotic Arm (RA) has operated for over 150 sols since the Lander touched down on the north polar region of Mars on May 25, 2008. During its mission it has dug numerous trenches in the Martian regolith, acquired samples of Martian dry and icy soil, and delivered them to the Thermal Evolved Gas Analyzer (TEGA) and the Microscopy, Electrochemistry, and Conductivity Analyzer (MECA). The RA inserted the Thermal and Electrical Conductivity Probe (TECP) into the Martian regolith and positioned it at various heights above the surface for relative humidity measurements. The RA was used to point the Robotic Arm Camera to take images of the surface, trenches, samples within the scoop, and other objects of scientific interest within its workspace. Data from the RA sensors during trenching, scraping, and trench cave-in experiments have been used to infer mechanical properties of the Martian soil. This paper describes the design and operations of the RA as a critical component of the Phoenix Mars Lander necessary to achieve the scientific goals of the mission.

Reorganization of Damaged Chromatin by the Exchange of Histone Variant H2A.Z-2

Energy Technology Data Exchange (ETDEWEB)

Nishibuchi, Ikuno [Department of Cellular Biology, Research Institute for Radiation Biology and Medicine, Hiroshima University, Hiroshima (Japan); Department of Radiation Oncology, Graduate School of Biomedical and Health Sciences, Hiroshima University, Hiroshima (Japan); Department of Radiation Oncology, Hiroshima Prefectural Hospital, Hiroshima (Japan); Suzuki, Hidekazu; Kinomura, Aiko; Sun, Jiying; Liu, Ning-Ang [Department of Cellular Biology, Research Institute for Radiation Biology and Medicine, Hiroshima University, Hiroshima (Japan); Horikoshi, Yasunori [Department of Cellular Biology, Research Institute for Radiation Biology and Medicine, Hiroshima University, Hiroshima (Japan); Research Center for Mathematics of Chromatin Live Dynamics, Hiroshima University, Hiroshima (Japan); Shima, Hiroki [Department of Biochemistry, Graduate School of Medical Sciences, Tohoku University, Sendai (Japan); Kusakabe, Masayuki; Harata, Masahiko [Laboratory of Molecular Biology, Graduate School of Agricultural Science, Tohoku University, Sendai (Japan); Fukagawa, Tatsuo [Department of Molecular Genetics, National Institute of Genetics and The Graduate University for Advanced Studies, Mishima (Japan); Ikura, Tsuyoshi [Laboratory of Chromatin Regulatory Network, Department of Mutagenesis, Radiation Biology Center, Kyoto University, Kyoto (Japan); Ishida, Takafumi [Department of Cardiovascular Medicine, Graduate School of Biomedical and Health Sciences, Hiroshima University, Hiroshima (Japan); Nagata, Yasushi [Department of Radiation Oncology, Graduate School of Biomedical and Health Sciences, Hiroshima University, Hiroshima (Japan); Tashiro, Satoshi, E-mail: ktashiro@hiroshima-u.ac.jp [Department of Cellular Biology, Research Institute for Radiation Biology and Medicine, Hiroshima University, Hiroshima (Japan); Research Center for Mathematics of Chromatin Live Dynamics, Hiroshima University, Hiroshima (Japan)

2014-07-15

Purpose: The reorganization of damaged chromatin plays an important role in the regulation of the DNA damage response. A recent study revealed the presence of 2 vertebrate H2A.Z isoforms, H2A.Z-1 and H2A.Z-2. However, the roles of the vertebrate H2A.Z isoforms are still unclear. Thus, in this study we examined the roles of the vertebrate H2A.Z isoforms in chromatin reorganization after the induction of DNA double-strand breaks (DSBs). Methods and Materials: To examine the dynamics of H2A.Z isoforms at damaged sites, we constructed GM0637 cells stably expressing each of the green fluorescent protein (GFP)-labeled H2A.Z isoforms, and performed fluorescence recovery after photobleaching (FRAP) analysis and inverted FRAP analysis in combination with microirradiation. Immunofluorescence staining using an anti-RAD51 antibody was performed to study the kinetics of RAD51 foci formation after 2-Gy irradiation of wild-type (WT), H2A.Z-1- and H2A.Z-2-deficient DT40 cells. Colony-forming assays were also performed to compare the survival rates of WT, H2A.Z-1-, and H2A.Z-2-deficient DT40 cells with control, and H2A.Z-1- and H2A.Z-2-depleted U2OS cells after irradiation. Results: FRAP analysis revealed that H2A.Z-2 was incorporated into damaged chromatin just after the induction of DSBs, whereas H2A.Z-1 remained essentially unchanged. Inverted FRAP analysis showed that H2A.Z-2 was released from damaged chromatin. These findings indicated that H2A.Z-2 was exchanged at DSB sites immediately after the induction of DSBs. RAD51 focus formation after ionizing irradiation was disturbed in H2A.Z-2-deficient DT40 cells but not in H2A.Z-1-deficient cells. The survival rate of H2A.Z-2-deficient cells after irradiation was lower than those of WT and H2A.Z-1- DT40 cells. Similar to DT40 cells, H2A.Z-2-depleted U2OS cells were also radiation-sensitive compared to control and H2A.Z-1-depleted cells. Conclusions: We found that vertebrate H2A.Z-2 is involved in the regulation of the DNA

Reorganization of Damaged Chromatin by the Exchange of Histone Variant H2A.Z-2

International Nuclear Information System (INIS)

Nishibuchi, Ikuno; Suzuki, Hidekazu; Kinomura, Aiko; Sun, Jiying; Liu, Ning-Ang; Horikoshi, Yasunori; Shima, Hiroki; Kusakabe, Masayuki; Harata, Masahiko; Fukagawa, Tatsuo; Ikura, Tsuyoshi; Ishida, Takafumi; Nagata, Yasushi; Tashiro, Satoshi

2014-01-01

Purpose: The reorganization of damaged chromatin plays an important role in the regulation of the DNA damage response. A recent study revealed the presence of 2 vertebrate H2A.Z isoforms, H2A.Z-1 and H2A.Z-2. However, the roles of the vertebrate H2A.Z isoforms are still unclear. Thus, in this study we examined the roles of the vertebrate H2A.Z isoforms in chromatin reorganization after the induction of DNA double-strand breaks (DSBs). Methods and Materials: To examine the dynamics of H2A.Z isoforms at damaged sites, we constructed GM0637 cells stably expressing each of the green fluorescent protein (GFP)-labeled H2A.Z isoforms, and performed fluorescence recovery after photobleaching (FRAP) analysis and inverted FRAP analysis in combination with microirradiation. Immunofluorescence staining using an anti-RAD51 antibody was performed to study the kinetics of RAD51 foci formation after 2-Gy irradiation of wild-type (WT), H2A.Z-1- and H2A.Z-2-deficient DT40 cells. Colony-forming assays were also performed to compare the survival rates of WT, H2A.Z-1-, and H2A.Z-2-deficient DT40 cells with control, and H2A.Z-1- and H2A.Z-2-depleted U2OS cells after irradiation. Results: FRAP analysis revealed that H2A.Z-2 was incorporated into damaged chromatin just after the induction of DSBs, whereas H2A.Z-1 remained essentially unchanged. Inverted FRAP analysis showed that H2A.Z-2 was released from damaged chromatin. These findings indicated that H2A.Z-2 was exchanged at DSB sites immediately after the induction of DSBs. RAD51 focus formation after ionizing irradiation was disturbed in H2A.Z-2-deficient DT40 cells but not in H2A.Z-1-deficient cells. The survival rate of H2A.Z-2-deficient cells after irradiation was lower than those of WT and H2A.Z-1- DT40 cells. Similar to DT40 cells, H2A.Z-2-depleted U2OS cells were also radiation-sensitive compared to control and H2A.Z-1-depleted cells. Conclusions: We found that vertebrate H2A.Z-2 is involved in the regulation of the DNA

A Statistical Approach for Gain Bandwidth Prediction of Phoenix-Cell Based Reflect arrays

Directory of Open Access Journals (Sweden)

Hassan Salti

2018-01-01

Full Text Available A new statistical approach to predict the gain bandwidth of Phoenix-cell based reflectarrays is proposed. It combines the effects of both main factors that limit the bandwidth of reflectarrays: spatial phase delays and intrinsic bandwidth of radiating cells. As an illustration, the proposed approach is successfully applied to two reflectarrays based on new Phoenix cells.

(Ca,Mg)-Carbonate and Mg-Carbonate at the Phoenix Landing Site: Evaluation of the Phoenix Lander's Thermal Evolved Gas Analyzer (TEGA) Data Using Laboratory Simulations

Science.gov (United States)

Sutter, B.; Ming, D. W.; Boynton, W. V.; Niles, P. B.; Morris, R. V.

2011-01-01

Calcium carbonate (4.5 wt. %) was detected in the soil at the Phoenix Landing site by the Phoenix Lander s The Thermal and Evolved Gas Analyzer [1]. TEGA operated at 12 mbar pressure, yet the detection of calcium carbonate is based on interpretations derived from thermal analysis literature of carbonates measured under ambient (1000 mbar) and vacuum (10(exp -3) mbar) conditions [2,3] as well as at 100 and 30 mbar [4,5] and one analysis at 12 mbar by the TEGA engineering qualification model (TEGA-EQM). Thermodynamics (Te = H/ S) dictate that pressure affects entropy ( S) which causes the temperature (Te) of mineral decomposition at one pressure to differ from Te obtained at another pressure. Thermal decomposition analyses of Fe-, Mg-, and Ca-bearing carbonates at 12 mbar is required to enhance the understanding of the TEGA results at TEGA operating pressures. The objectives of this work are to (1) evaluate the thermal and evolved gas behavior of a suite of Fe-, Mg-, Ca-carbonate minerals at 1000 and 12 mbar and (2) discuss possible emplacement mechanisms for the Phoenix carbonate.

PHOENIX MARS MECA NON-IMAGING EDR V1.0

Data.gov (United States)

National Aeronautics and Space Administration — The Microscopy, Electrochemistry, and Conductivity Analyzer (MECA) experiment on the Mars Phoenix Lander consists of four instrument components plus command...

ALPHA/PHOENIX-P/ANC system validation for Angra-1 neutronic calculations

International Nuclear Information System (INIS)

Ponzoni Filho, Pedro; Sato, Sadakatu; Santos, Teresinha Ipojuca Cardoso; Fernandes, Vanderlei Borba; Fetterman, R.J.

1995-01-01

The ALPHA/PHOENIX-P/ANC (APA) code package is an advanced neutronic calculation system for pressurized water reactor (PWR). PHOENIX-P generates the required cross sections for the fuel, burnable absorbers, control rods and baffle/reflector region. The ALPHA code is used to automate the generation of these cross-sections as well as process the PHOENIX-P results to generate the ANC model input. ANC is a three dimensional advanced nodal code used for the modeling of the, depletion of the fuel in the core, and for the calculation of power distributions, rod worths and other reactivity parameters. This paper provides brief overview of the APA methodology for reload core design of Angra Unit 1 Cycles 1 and 2. Results included are predicted power distributions, control rod worths and other reactivity parameters compared to plant measurements. These results demonstrate that the APA system can be used for the reload core design. (author). 7 refs, 9 figs

ALPHA/PHOENIX-P/ANC system validation for Angra-1 neutronic calculations

Energy Technology Data Exchange (ETDEWEB)

Ponzoni Filho, Pedro; Sato, Sadakatu; Santos, Teresinha Ipojuca Cardoso; Fernandes, Vanderlei Borba [FURNAS, Rio de Janeiro, RJ (Brazil); Fetterman, R.J. [Westinghouse Electric Corp., Pittsburgh, PA (United States)

1995-12-31

The ALPHA/PHOENIX-P/ANC (APA) code package is an advanced neutronic calculation system for pressurized water reactor (PWR). PHOENIX-P generates the required cross sections for the fuel, burnable absorbers, control rods and baffle/reflector region. The ALPHA code is used to automate the generation of these cross-sections as well as process the PHOENIX-P results to generate the ANC model input. ANC is a three dimensional advanced nodal code used for the modeling of the, depletion of the fuel in the core, and for the calculation of power distributions, rod worths and other reactivity parameters. This paper provides brief overview of the APA methodology for reload core design of Angra Unit 1 Cycles 1 and 2. Results included are predicted power distributions, control rod worths and other reactivity parameters compared to plant measurements. These results demonstrate that the APA system can be used for the reload core design. (author). 7 refs, 9 figs.

How Neoliberal Imperialism is Expressed by Programming Strategies of Phoenix TV: A Critical Case Study

Directory of Open Access Journals (Sweden)

Shuang Xie

2013-05-01

Full Text Available This project is a case study of Phoenix Television, which is a Hong Kong-based satellite TV network broadcasting to the global Chinese-speaking community, primarily to the mainland of China. In the theoretical framework of media imperialism and neoliberal imperialism, this study focuses on the programming strategies of Phoenix TV and examines how the global trend of neoliberalism, the Chinese government’s tight control of the media, and the sophisticated ownership of Phoenix TV intertwined to influence on its programming. The analysis of the format, content, naming, and scheduling reveals that US-inspired neoliberalism is expressed in the network’s programming strategies. This expression, in fact, is the balance that Phoenix found between the tension of global and Chinese interests, the tension between revenue making and public service, and the tension between Party-control and profit seeking.

Rhizosphere effects of PAH-contaminated soil phytoremediation using a special plant named Fire Phoenix.

Science.gov (United States)

Liu, Rui; Xiao, Nan; Wei, Shuhe; Zhao, Lixing; An, Jing

2014-03-01

The rhizosphere effect of a special phytoremediating species known as Fire Phoenix on the degradation of polycyclic aromatic hydrocarbons (PAHs) was investigated, including changes of the enzymatic activity and microbial communities in rhizosphere soil. The study showed that the degradation rate of Σ8PAHs by Fire Phoenix was up to 99.40% after a 150-day culture. The activity of dehydrogenase (DHO), peroxidase (POD) and catalase (CAT) increased greatly, especially after a 60-day culture, followed by a gradual reduction with an increase in the planting time. The activity of these enzymes was strongly correlated to the higher degradation performance of Fire Phoenix growing in PAH-contaminated soils, although it was also affected by the basic characteristics of the plant species itself, such as the excessive, fibrous root systems, strong disease resistance, drought resistance, heat resistance, and resistance to barren soil. The activity of polyphenoloxidase (PPO) decreased during the whole growing period in this study, and the degradation rate of Σ8PAHs in the rhizosphere soil after having planted Fire Phoenix plants had a significant (R(2)=0.947) negative correlation with the change in the activity of PPO. Using an analysis of the microbial communities, the results indicated that the structure of microorganisms in the rhizosphere soil could be changed by planting Fire Phoenix plants, namely, there was an increase in microbial diversity compared with the unplanted soil. In addition, the primary advantage of Fire Phoenix was to promote the growth of flora genus Gordonia sp. as the major bacteria that can effectively degrade PAHs. Crown Copyright © 2013. Published by Elsevier B.V. All rights reserved.

Enhancing Microstructure and Mechanical Properties of AZ31-MWCNT Nanocomposites through Mechanical Alloying

Directory of Open Access Journals (Sweden)

J. Jayakumar

2013-01-01

Full Text Available Multiwall carbon nanotubes (MWCNTs reinforced Mg alloy AZ31 nanocomposites were fabricated by mechanical alloying and powder metallurgy technique. The reinforcement material MWCNTs were blended in three weight fractions (0.33%, 0.66%, and 1% with the matrix material AZ31 (Al-3%, zinc-1% rest Mg and blended through mechanical alloying using a high energy planetary ball mill. Specimens of monolithic AZ31 and AZ31-MWCNT composites were fabricated through powder metallurgy technique. The microstructure, density, hardness, porosity, ductility, and tensile properties of monolithic AZ31 and AZ31-MWCNT nano composites were characterized and compared. The characterization reveals significant reduction in CNT (carbon nanoTube agglomeration and enhancement in microstructure and mechanical properties due to mechanical alloying through ball milling.

Discovery Learning: Zombie, Phoenix, or Elephant?

Science.gov (United States)

Bakker, Arthur

2018-01-01

Discovery learning continues to be a topic of heated debate. It has been called a zombie, and this special issue raises the question whether it may be a phoenix arising from the ashes to which the topic was burnt. However, in this commentary I propose it is more like an elephant--a huge topic approached by many people who address different…

78 FR 4138 - Chief of Engineers Environmental Advisory Board; Meeting

Science.gov (United States)

2013-01-18

... (SDOCH), 401 West Washington Street, Phoenix, AZ 85003-21178. Agenda: The Board will advise the Chief of... interested person may attend. However, all attendees will enter and exit SDOCH through the appropriate...

Electrochemical corrosion behavior of AZ91D alloy in ethylene glycol

Energy Technology Data Exchange (ETDEWEB)

Fekry, A.M. [Chemistry Department, Faculty of Science, Cairo University, Giza 12613 (Egypt)], E-mail: hham4@hotmail.com; Fatayerji, M.Z. [Chemistry Department, Faculty of Science, Cairo University, Giza 12613 (Egypt)

2009-11-01

The effect of concentration on the corrosion behavior of Mg-based alloy AZ91D was investigated in ethylene glycol-water solutions using electrochemical techniques i.e. potentiodynamic polarization, electrochemical impedance measurements (EIS) and surface examination via scanning electron microscope (SEM) technique. This can provide a basis for developing new coolants for magnesium alloy engine blocks. Corrosion behavior of AZ91D alloy by coolant is important in the automotive industry. It was found that the corrosion rate of AZ91D alloy decreased with increasing concentration of ethylene glycol. For AZ91D alloy in chloride >0.05 M or fluoride <0.05 M containing 30% ethylene glycol solution, they are more corrosive than the blank (30% ethylene glycol-70% water). However, at concentrations <0.05 for chloride or >0.05 M for fluoride containing ethylene glycol solution, some inhibition effect has been observed. The corrosion of AZ91D alloy in the blank can be effectively inhibited by addition of 0.05 mM paracetamol that reacts with AZ91D alloy and forms a protective film on the surface at this concentration as confirmed by surface examination.

ANALYSIS RESULTS FOR BUILDING 241 702-AZ A TRAIN

International Nuclear Information System (INIS)

DUNCAN JB; FRYE JM; COOKE CA; LI SW; BROCKMAN FJ

2006-01-01

This report presents the analyses results for three samples obtained under RPP-PLAN-28509, Sampling and Analysis Plan for Building 241 702-AZ A Train. The sampling and analysis was done in response to problem evaluation request number PER-2004-6139, 702-AZ Filter Rooms Need Radiological Cleanup Efforts

ANALYSIS RESULTS FOR BUILDING 241 702-AZ A TRAIN

Energy Technology Data Exchange (ETDEWEB)

DUNCAN JB; FRYE JM; COOKE CA; LI SW; BROCKMAN FJ

2006-12-13

This report presents the analyses results for three samples obtained under RPP-PLAN-28509, Sampling and Analysis Plan for Building 241 702-AZ A Train. The sampling and analysis was done in response to problem evaluation request number PER-2004-6139, 702-AZ Filter Rooms Need Radiological Cleanup Efforts.

Test report : alternative fuels propulsion durability evaluation

Science.gov (United States)

2012-08-28

This document, prepared by Honeywell Aerospace, Phoenix, AZ (Honeywell), contains the final : test report (public version) for the U.S. Department of Transportation/Federal Aviation : Administration (USDOT/FAA) Alternative Fuels Propulsion Engine Dur...

Vertical Distribution of Water at Phoenix

Science.gov (United States)

Tamppari, L. K.; Lemmon, M. T.

2011-01-01

Phoenix results, combined with coordinated observations from the Mars Reconnaissance Orbiter of the Phoenix lander site, indicate that the water vapor is nonuniform (i.e., not well mixed) up to a calculated cloud condensation level. It is important to understand the mixing profile of water vapor because (a) the assumption of a well-mixed atmosphere up to a cloud condensation level is common in retrievals of column water abundances which are in turn used to understand the seasonal and interannual behavior of water, (b) there is a long history of observations and modeling that conclude both that water vapor is and is not well-mixed, and some studies indicate that the water vapor vertical mixing profile may, in fact, change with season and location, (c) the water vapor in the lowest part of the atmosphere is the reservoir that can exchange with the regolith and higher amounts may have an impact on the surface chemistry, and (d) greater water vapor abundances close to the surface may enhance surface exchange thereby reducing regional transport, which in turn has implications to the net transport of water vapor over seasonal and annual timescales.

Influence of artificial biological fluid composition on the biocorrosion of potential orthopedic Mg-Ca, AZ31, AZ91 alloys

International Nuclear Information System (INIS)

Gu, X N; Zheng, Y F; Chen, L J

2009-01-01

The electrochemical behavior of potential orthopedic Mg-Ca, AZ31 and AZ91 alloys was studied in Hank's solution, Dulbecco's Modified Eagle's Medium (DMEM) and serum-containing medium (DMEM adding 10% fetal bovine serum (DMEM+FBS)) over a 7 day immersion period. The biocorrosion of the above three alloys for various immersion time intervals was investigated by linear polarization and electrochemical impedance spectroscopy (EIS). After 7 day immersion, potentiodynamic polarization tests were carried out and the surface morphologies of experimental samples were examined by scanning electron microscopy (SEM) observation complemented by energy-disperse spectrometer (EDS) analysis. It was shown that the corrosion of magnesium alloys was influenced by the composition of the solution. The results indicated that chloride ion could reduce the corrosion resistance and the hydrocarbonate ions could induce rapid surface passivation. The adsorbed amino acid on the experimental magnesium alloys' surface increased their polarization resistance and reduced current densities. The influence of the serum protein on corrosion was found to be associated with the magnesium alloy compositions. A Mg-Ca alloy exhibited an increased corrosion rate in the presence of serum protein. An AZ31 alloy showed an increased corrosion rate in DMEM+FBS in the initial 3 day immersion and the corrosion rate decreased thereafter. An AZ91 alloy, with high Al content, showed a reduced corrosion rate with the addition of FBS into DMEM.

Influence of artificial biological fluid composition on the biocorrosion of potential orthopedic Mg-Ca, AZ31, AZ91 alloys.

Science.gov (United States)

Gu, X N; Zheng, Y F; Chen, L J

2009-12-01

The electrochemical behavior of potential orthopedic Mg-Ca, AZ31 and AZ91 alloys was studied in Hank's solution, Dulbecco's Modified Eagle's Medium (DMEM) and serum-containing medium (DMEM adding 10% fetal bovine serum (DMEM+FBS)) over a 7 day immersion period. The biocorrosion of the above three alloys for various immersion time intervals was investigated by linear polarization and electrochemical impedance spectroscopy (EIS). After 7 day immersion, potentiodynamic polarization tests were carried out and the surface morphologies of experimental samples were examined by scanning electron microscopy (SEM) observation complemented by energy-disperse spectrometer (EDS) analysis. It was shown that the corrosion of magnesium alloys was influenced by the composition of the solution. The results indicated that chloride ion could reduce the corrosion resistance and the hydrocarbonate ions could induce rapid surface passivation. The adsorbed amino acid on the experimental magnesium alloys' surface increased their polarization resistance and reduced current densities. The influence of the serum protein on corrosion was found to be associated with the magnesium alloy compositions. A Mg-Ca alloy exhibited an increased corrosion rate in the presence of serum protein. An AZ31 alloy showed an increased corrosion rate in DMEM+FBS in the initial 3 day immersion and the corrosion rate decreased thereafter. An AZ91 alloy, with high Al content, showed a reduced corrosion rate with the addition of FBS into DMEM.

241-AZ Tank Farm Construction Extent of Condition Review for Tank Integrity

Energy Technology Data Exchange (ETDEWEB)

Barnes, Travis J.; Boomer, Kayle D.; Gunter, Jason R.; Venetz, Theodore J.

2013-07-30

This report provides the results of an extent of condition construction history review for tanks 241-AZ-101 and 241-AZ-102. The construction history of the 241-AZ tank farm has been reviewed to identify issues similar to those experienced during tank AY-102 construction. Those issues and others impacting integrity are discussed based on information found in available construction records, using tank AY-102 as the comparison benchmark. In the 241-AZ tank farm, the second DST farm constructed, both refractory quality and tank and liner fabrication were improved.

241-AY/AZ waste storage tanks: Supplemental gravity load analysis. Volume 1

International Nuclear Information System (INIS)

Baliga, R.

1994-01-01

An analysis of the 241SY tanks performed by ADVENT(1994b) to resolve dome overload issues indicated that the tank can sustain the dome loads resulting from additional soil overburden depth, increased soil density, and increased concentrated load. Similar issues exist for the 241AY/AZ tanks and therefore, an interim analysis of the 241AY/AZ tanks is presented herein. The scope of this effort is to review and compare all design drawings pertaining to the 241AY and 241AZ tanks with those pertaining to the 241SY tanks; to modify the axisymmetric model of the 241SY tanks to represent the 241AY/AZ tanks; and to evaluate the effect of additional dome load on the 241AY/AZ tanks by performing a structural analysis for gravity loads (dead load + live load). ADVENTS's additional scope of work is to perform a qualitative evaluation of the 241AY/AZ tanks for seismic and thermal loadings (Vollert 1982 and Blume 1971). This qualitative evaluation does not include any detailed finite element analysis of the tanks. The following design-based gravity loading conditions are used in this interim analysis of the 241AY/AZ tanks to determine a baseline for the tank stresses or section loads

Grain refinement of AZ31 magnesium alloy by electromagnetic ...

Indian Academy of Sciences (India)

Low-frequency electromagnetic field; AZ31 magnesium alloy; Al4C3; grain refinement. Abstract. The effects of electromagnetic stirring and Al4C3 grain refiner on the grain refinement of semicontinuously cast AZ31 magnesium alloy were discussed in this investigation. The results indicate that electromagnetic stirring has an ...

Caustic leaching of composite AZ-101/AZ-102 Hanford tank sludge

International Nuclear Information System (INIS)

Rapko, B.M.; Wagner, M.J.

1997-07-01

To reduce the quantity (and hence the cost) of glass canisters needed for disposing of high-level radioactive wastes from the Hanford tank farms, pretreatment processes are needed to remove as much nonradioactive material as possible. This report describes the results of a laboratory-scale caustic leaching test performed on a composite derived from a combination of 241-AZ-101 and 241-AZ-102 Hanford Tank sludges. The goals of this FY 1996 test were to evaluate the effectiveness of caustic leaching on removing key components from the sludge and to evaluate the effectiveness of varying the free-hydroxide concentrations by incrementally increasing the free hydroxide concentration of the leach steps up to 3 M free hydroxide. Particle-size analysis of the treated and untreated sludge indicated that the size and range of the sludge particles remained essentially unchanged by the caustic leaching treatment. Both before and after caustic leaching, a particle range of 0.2 microm to 50 microm was observed, with mean particle diameters of 8.5 to 9 microm based on the volume distribution and mean particle diameters of 0.3 to 0.4 microm based on the number distribution

In aftermath of financial investigation Phoenix VA employee demoted after her testimony

Directory of Open Access Journals (Sweden)

Robbins RA

2013-03-01

Full Text Available No abstract available. Article truncated after 150 words. A previous Southwest Journal of Pulmonary and Critical Care Journal editorial commented on fiscal mismanagement at the Department of Veterans Affairs (VA Medical Center in Phoenix (1. Now Paula Pedene, the former Phoenix VA public affairs officer, claims she was demoted for testimony she gave to the VA Inspector General’s Office (OIG regarding that investigation (2. In 2011, the OIG investigated the Phoenix VA for excess spending on private care of patients (3. The report blamed systemic failures for controls so weak that $56 million in medical fees were paid during 2010 without adequate review. The report particularly focused on one clinician assigned by the Chief of Staff to review hundreds of requests per week and the intensive care unit physicians for transferring patients to chronic ventilator units (1,3. After the investigation, the director and one of the associate directors left the VA and the chief of staff was promoted …

Phoenix : Complex Adaptive System of Systems (CASoS) engineering version 1.0.

Energy Technology Data Exchange (ETDEWEB)

Moore, Thomas W.; Quach, Tu-Thach; Detry, Richard Joseph; Conrad, Stephen Hamilton; Kelic, Andjelka; Starks, Shirley J.; Beyeler, Walter Eugene; Brodsky, Nancy S.; Verzi, Stephen J.; Brown, Theresa Jean; Glass, Robert John, Jr.; Sunderland, Daniel J.; Mitchell, Michael David; Ames, Arlo Leroy; Maffitt, S. Louise; Finley, Patrick D.; Russell, Eric Dean; Zagonel, Aldo A.; Reedy, Geoffrey E.; Mitchell, Roger A.; Corbet, Thomas Frank, Jr.; Linebarger, John Michael

2011-08-01

Complex Adaptive Systems of Systems, or CASoS, are vastly complex ecological, sociological, economic and/or technical systems which we must understand to design a secure future for the nation and the world. Perturbations/disruptions in CASoS have the potential for far-reaching effects due to pervasive interdependencies and attendant vulnerabilities to cascades in associated systems. Phoenix was initiated to address this high-impact problem space as engineers. Our overarching goals are maximizing security, maximizing health, and minimizing risk. We design interventions, or problem solutions, that influence CASoS to achieve specific aspirations. Through application to real-world problems, Phoenix is evolving the principles and discipline of CASoS Engineering while growing a community of practice and the CASoS engineers to populate it. Both grounded in reality and working to extend our understanding and control of that reality, Phoenix is at the same time a solution within a CASoS and a CASoS itself.

Bioetanol de la caña de azúcar

Directory of Open Access Journals (Sweden)

N. Aguilar-Rivera

2007-01-01

Full Text Available La búsqueda de la viabilidad y desarrollo de la agroindustria de la caña de azúcar es ya una política imperativa. La producción de caña y azúcar constituyen la principal agroindustria del país, con presencia en 57 ingenios azucareros, localizados en 15 estados de la república. Sin embargo, la actual ineficiencia productiva, altos costos y otras causas —como la entrada de jarabe de maíz de alta fructosa (HFCS de menor costo— han desplazado el consumo interno de azúcar de caña, principalmente en bebidas embotelladas. Todos estos factores han contribuido a la actual y prolongada crisis del sector azucarero. Por lo tanto, la industria debe reestructurarse y reducir la producción de azúcar hacia la competitividad, con la alternativa del etanol combustible en la búsqueda de un futuro para la industria azucarera en México. Con la producción de etanol (EtOH a gran escala, por parte de los ingenios azucareros, es posible visualizar un nuevo y futuro mercado de uso de energías renovables en México, oportunidades para la exportación e incrementar los beneficios ambientales y económicos a través de su uso. La flexibilidad de la producción combinada, de azúcar y etanol en los ingenios, permitirá alcanzar esquemas y objetivos ambientales como nación. Para la industria azucarera, su mayor competidesafío, en este sentido, representa disminuir los costos actuales de producción de etanol a través del uso de la ingeniería genética, uso de diferentes materias primas y la totalidad de la planta de caña de azúcar e introducir mejoras tecnológicas.

PHOENIX MARS MECA OPTICAL MICROSCOPE 2 EDR VERSION 1.0

Data.gov (United States)

National Aeronautics and Space Administration — The Microscopy, Electrochemistry, and Conductivity Analyzer (MECA) experiment on the Mars Phoenix Lander consists of four instrument components plus command...

ARSENIC REMOVAL FROM DRINKING WATER BY ADSORPTIVE MEDIA, USEPA DEMONSTRATION PROJECT AT RIMROCK, AZ, SIX-MONTH EVALUATION REPORT

Science.gov (United States)

This report documents the activities performed during and the results obtained from the first six months of the arsenic removal treatment technology demonstration project at Rimrock, AZ. The objectives of the project are to evaluate the effectiveness of AdEdge Arsenic Package Uni...

Comparison of simulants to actual neutralized current acid waste: process and product testing of three NCAW core samples from Tanks 101-AZ and 102-AZ

Energy Technology Data Exchange (ETDEWEB)

Morrey, E.V.; Tingey, J.M.; Elliott, M.L.

1996-10-01

A vitrification plant is planned to process the high-level waste (HLW) solids from Hanford Site tanks into canistered glass logs for disposal in a national repository. Programs were established within the Pacific Northwest Laboratory Vitrification Technology Development (PVTD) Project to test and model simulated waste to support design, feed processability, operations, permitting, safety, and waste-form qualification. Parallel testing with actual radioactive waste was performed on a laboratory-scale to confirm the validity of using simulants and glass property models developed from simulants. Laboratory-scale testing has been completed on three radioactive core samples from tanks 101-AZ and 102-AZ containing neutralized current acid waste (NCAW), which is one of the first waste types to be processed in the high-level waste vitrification plant under a privatization scenario. Properties of the radioactive waste measured during process and product testing were compared to simulant properties and model predictions to confirm the validity of simulant and glass property ,models work. This report includes results from the three NCAW core samples, comparable results from slurry and glass simulants, and comparisons to glass property model predictions.

Comparison of simulants to actual neutralized current acid waste: Process and product testing of three NCAW core samples from Tanks 101-AZ and 102-AZ

Energy Technology Data Exchange (ETDEWEB)

Morrey, E.V.; Tingey, J.M.

1996-04-01

A vitrification plant is planned to process the high-level waste (HLW) solids from Hanford Site tanks into canistered glass logs for disposal in a national repository. Programs have been established within the Pacific Northwest Laboratory Vitrification Technology Development (PVTD) Project to test and model simulated waste to support design, feed processability, operations, permitting, safety, and waste-form qualification. Parallel testing with actual radioactive waste is being performed on a laboratory-scale to confirm the validity of using simulants and glass property models developed from simulants. Laboratory-scale testing has been completed on three radioactive core samples from tanks 101-AZ and 102-AZ containing neutralized current acid waste (NCAW), which is one of the first waste types to be processed in the high-level waste vitrification plant under a privatization scenario. Properties of the radioactive waste measured during process and product testing were compared to simulant properties and model predictions to confirm the validity of simulant and glass property models work. This report includes results from the three NCAW core samples, comparable results from slurry and glass simulants, and comparisons to glass property model predictions.

Comparison of simulants to actual neutralized current acid waste: process and product testing of three NCAW core samples from Tanks 101-AZ and 102-AZ

International Nuclear Information System (INIS)

Morrey, E.V.; Tingey, J.M.; Elliott, M.L.

1996-10-01

A vitrification plant is planned to process the high-level waste (HLW) solids from Hanford Site tanks into canistered glass logs for disposal in a national repository. Programs were established within the Pacific Northwest Laboratory Vitrification Technology Development (PVTD) Project to test and model simulated waste to support design, feed processability, operations, permitting, safety, and waste-form qualification. Parallel testing with actual radioactive waste was performed on a laboratory-scale to confirm the validity of using simulants and glass property models developed from simulants. Laboratory-scale testing has been completed on three radioactive core samples from tanks 101-AZ and 102-AZ containing neutralized current acid waste (NCAW), which is one of the first waste types to be processed in the high-level waste vitrification plant under a privatization scenario. Properties of the radioactive waste measured during process and product testing were compared to simulant properties and model predictions to confirm the validity of simulant and glass property ,models work. This report includes results from the three NCAW core samples, comparable results from slurry and glass simulants, and comparisons to glass property model predictions

Comparison of simulants to actual neutralized current acid waste: Process and product testing of three NCAW core samples from Tanks 101-AZ and 102-AZ

International Nuclear Information System (INIS)

Morrey, E.V.; Tingey, J.M.

1996-04-01

A vitrification plant is planned to process the high-level waste (HLW) solids from Hanford Site tanks into canistered glass logs for disposal in a national repository. Programs have been established within the Pacific Northwest Laboratory Vitrification Technology Development (PVTD) Project to test and model simulated waste to support design, feed processability, operations, permitting, safety, and waste-form qualification. Parallel testing with actual radioactive waste is being performed on a laboratory-scale to confirm the validity of using simulants and glass property models developed from simulants. Laboratory-scale testing has been completed on three radioactive core samples from tanks 101-AZ and 102-AZ containing neutralized current acid waste (NCAW), which is one of the first waste types to be processed in the high-level waste vitrification plant under a privatization scenario. Properties of the radioactive waste measured during process and product testing were compared to simulant properties and model predictions to confirm the validity of simulant and glass property models work. This report includes results from the three NCAW core samples, comparable results from slurry and glass simulants, and comparisons to glass property model predictions

Influence of artificial biological fluid composition on the biocorrosion of potential orthopedic Mg-Ca, AZ31, AZ91 alloys

Energy Technology Data Exchange (ETDEWEB)

Gu, X N; Zheng, Y F [State Key Laboratory for Turbulence and Complex System and Department of Advanced Materials and Nanotechnology, College of Engineering, Peking University, Beijing 100871 (China); Chen, L J, E-mail: yfzheng@pku.edu.c [School of Material Science and Engineering, Shengyang University of Technology, Shenyang 110023 (China)

2009-12-15

The electrochemical behavior of potential orthopedic Mg-Ca, AZ31 and AZ91 alloys was studied in Hank's solution, Dulbecco's Modified Eagle's Medium (DMEM) and serum-containing medium (DMEM adding 10% fetal bovine serum (DMEM+FBS)) over a 7 day immersion period. The biocorrosion of the above three alloys for various immersion time intervals was investigated by linear polarization and electrochemical impedance spectroscopy (EIS). After 7 day immersion, potentiodynamic polarization tests were carried out and the surface morphologies of experimental samples were examined by scanning electron microscopy (SEM) observation complemented by energy-disperse spectrometer (EDS) analysis. It was shown that the corrosion of magnesium alloys was influenced by the composition of the solution. The results indicated that chloride ion could reduce the corrosion resistance and the hydrocarbonate ions could induce rapid surface passivation. The adsorbed amino acid on the experimental magnesium alloys' surface increased their polarization resistance and reduced current densities. The influence of the serum protein on corrosion was found to be associated with the magnesium alloy compositions. A Mg-Ca alloy exhibited an increased corrosion rate in the presence of serum protein. An AZ31 alloy showed an increased corrosion rate in DMEM+FBS in the initial 3 day immersion and the corrosion rate decreased thereafter. An AZ91 alloy, with high Al content, showed a reduced corrosion rate with the addition of FBS into DMEM.

The Phoenix Physician: defining a pathway toward leadership in patient-centered care.

Science.gov (United States)

Good, Robert G; Bulger, John B; Hasty, Robert T; Hubbard, Kevin P; Schwartz, Elliott R; Sutton, John R; Troutman, Monte E; Nelinson, Donald S

2012-08-01

Health care delivery has evolved in reaction to scientific and technological discoveries, emergent patient needs, and market forces. A current focus on patient-centered care has pointed to the need for the reallocation of resources to improve access to and delivery of efficient, cost-effective, quality care. In response to this need, primary care physicians will find themselves in a new role as team leader. The American College of Osteopathic Internists has developed the Phoenix Physician, a training program that will prepare primary care residents and practicing physicians for the changes in health care delivery and provide them with skills such as understanding the contributions of all team members (including an empowered and educated patient), evaluating and treating patients, and applying performance metrics and information technology to measure and improve patient care and satisfaction. Through the program, physicians will also develop personal leadership and communication skills.

Influence of the Composition of the Hank’s Balanced Salt Solution on the Corrosion Behavior of AZ31 and AZ61 Magnesium Alloys

Czech Academy of Sciences Publication Activity Database

Tkacz, J.; Slouková, K.; Minda, J.; Drábiková, J.; Fintová, Stanislava; Doležal, P.; Wasserbauer, J.

2017-01-01

Roč. 7, č. 11 (2017), č. článku 465. ISSN 2075-4701 Institutional support: RVO:68081723 Keywords : magnesium alloy * AZ31 * AZ61 * HBSS * HBSS+ * EIS * potentiodynamic test Subject RIV: JK - Corrosion ; Surface Treatment of Materials OBOR OECD: Coating and films Impact factor: 1.984, year: 2016 http://www.mdpi.com/2075-4701/7/11/465

Microstructural Characteristics and Mechanical Properties of 2205/AZ31B Laminates Fabricated by Explosive Welding

Directory of Open Access Journals (Sweden)

Yan Li

2017-04-01

Full Text Available A bimetal composite of 2205 duplex stainless steel and AZ31B magnesium alloy was cladded successfully through the method of explosive welding. The microstructural characteristics and mechanical properties of 2205/AZ31B bimetal composite are discussed. The interface of 2205/AZ31B bimetallic composite was a less regular wavy morphology with locally melted pockets. Adiabatic shear bands occurred only in the AZ31B side near explosive welding interface. The microstructure observed with EBSD showed a strong refinement near the interface zones. Line scan confirmed that the interface had a short element diffusion zone which would contribute to the metallurgical bonding between 2205 duplex stainless steel and AZ31B magnesium alloy. The value of micro-hardness near the bonding interface of composite plate increased because of work hardening and grain refinement. The tensile shear strength of bonding interface of 2205/AZ31B composite was 105.63 MPa. Tensile strength of 2205/AZ31B composite material was higher than the base AZ31B. There were two abrupt drops in stress in the stress–strain curves of the 2205/AZ31B composite materials.

EnviroAtlas - Phoenix, AZ - Greenspace Proximity Gradient

Data.gov (United States)

U.S. Environmental Protection Agency — In any given 1-square meter point in this EnviroAtlas dataset, the value shown gives the percentage of square meters of greenspace within 1/4 square kilometer...

Pengaruh waktu kontak terhadap kualitas sambungan hasil las gesek (Friction Welding Magnesium AZ-31

Directory of Open Access Journals (Sweden)

Solihin Solihin

2018-01-01

Full Text Available Abstrak: Pengelasan merupakan salah suatu proses penyambungan dua atau lebih bahan teknik, dengan atau tanpa peroses pencairan logam dasarnya. Teknologi Las Gesek (Friction Welding, FW merupakan salah satu teknik pengelasan padat atau pengelasan tanpa proses pencairan (solid-state welding. Pembangkitan panas dalam proses FW dihasilkan dengan cara menggesekkan permukaan material las (base metal hingga mencapai temperatur penyambungannya (semi-solid temperature atau sekitar 80% dari temperature cair bahan, dan dalam hal Magnesium AZ31 adalah sekitar temperatur 5500C. Setelah bahan mencapai temperatur semi-solid tersebut, kemudian diberi tekanan agar terjadi proses penyambungan. Penelitian ini bertujuan untuk mengetahui pengaruh variasi proses terhadap kualitas hasil pengelasan gesek, yang meliputi: kekuatan tarik, struktur makro, dan nilai kekerasan bahan hasil las. Parameter pengujiannya adalah variasi waktu kontak las, yaitu selama 3, 5, dan 10 menit. Kecepatan putar spindle selama proses pengelasan ditetapkan 1400 rpm. Hasil pengelasan menunjukkan bahwa waktu kontak gesek 3 menit menghasilkan kekuatan tarik tertinggi (16,78 MPa, bila dibandingkan dengan dua parameter lain. Hasil uji keras pada daerah las (stir zone menunjukkan angka kekerasan rata-rata yang relative konsisten, atau sebesar 60 HRE untuk semua parameter, sedangkan angka kekerasan rata-rata di daerah terpengaruh panas (heat affected zone, HAZ untuk waktu kontak gesek 3, 5 dan 10 menit secara berturut-turut adalah sebesar 69,6; 64,6; dan 60,6 HRE. Hasil penelitian awal ini memberikan potensi studi lanjutan pada berbagai parameter pengelasan lain agar didapatkan kualitas sambungan las gesek yang optimum untuk proses pengelasan gesek Magnesium AZ-31. Kata Kunci: Las gesek, Magnesium AZ-31, struktur makro, cacat void. Abstract: Welding is a process technology aiming to join two or more materials. Friction Welding (FW is including in a solid-state technology cluster, where the heat is

AZ91C magnesium alloy modified by Cd

DEFF Research Database (Denmark)

Shabadi, R.; Ambat, Rajan; Dwarakadasa, E.S.

2014-01-01

In the present work, the effect of Cd on the microstructure, mechanical properties and general corrosion behaviour of AZ91C alloys was investigated. Addition of Cd was found not to be efficient in modifying/refining the microstructure or β-phase. A morphology change in β-phase from fine continuous...... precipitates to discontinuous β-phase upon the addition of Cd was observed. A marginal increment in mechanical properties was observed. General corrosion behaviour was followed with weight loss measurements, potentiostatic polarisation studies and surface studies in 3.5% sodium chloride solution and 3.......5% sodium chloride with 2% potassium dichromate solution. Cd addition deteriorated the corrosion behaviour of AZ91C. This behaviour was attributed to the formation of chunks of β-phase upon the addition of Cd. AZ91C with refined β-phase distribution, performed rather better in the NaCl solutions....

Telltale wind indicator for the Mars Phoenix lander

DEFF Research Database (Denmark)

Gunnlaugsson, H.P.; Honstein-Rathlou, C.; Merrison, J.P.

2008-01-01

The Telltale wind indicator is a mechanical anemometer designed to operate on the Martian surface as part of the meteorological package on the NASA Phoenix lander. It consists of a lightweight cylinder suspended by Kevlar fibers and is deflected under the action of wind. Imaging of the Telltale...

76 FR 18378 - Amendment of Class E Airspace; Taylor, AZ

Science.gov (United States)

2011-04-04

...-1189; Airspace Docket No. 10-AWP-19] Amendment of Class E Airspace; Taylor, AZ AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Final rule. SUMMARY: This action will amend Class E airspace at Taylor Airport, Taylor, AZ, to accommodate aircraft using the CAMBO One Departure, and the Area Navigation (RNAV...

System Description for Tank 241-AZ-101 Waste Retrieval Data Acquisition System

International Nuclear Information System (INIS)

ROMERO, S.G.

2000-01-01

The proposed activity provides the description of the Data Acquisition System for Tank 241-AZ-101. This description is documented in HNF-5572, Tank 241-AZ-101 Waste Retrieval Data Acquisition System (DAS). This activity supports the planned mixer pump tests for Tank 241-AZ-101. Tank 241-AZ-101 has been selected for the first full-scale demonstration of a mixer pump system. The tank currently holds over 960,000 gallons of neutralized current acid waste, including approximately 12.7 inches of settling solids (sludge) at the bottom of the tank. As described in Addendum 4 of the FSAR (LMHC 2000a), two 300 HP mixer pumps with associated measurement and monitoring equipment have been installed in Tank 241-AZ-101. The purpose of the Tank 241-AZ-101 retrieval system Data Acquisition System (DAS) is to provide monitoring and data acquisition of key parameters in order to confirm the effectiveness of the mixer pumps utilized for suspending solids in the tank. The suspension of solids in Tank 241-AZ-101 is necessary for pretreatment of the neutralized current acid waste and eventual disposal as glass via the Hanford Waste Vitrification Plant. HNF-5572 provides a basic description of the Tank 241-AZ-101 retrieval system DAS, including the field instrumentation and application software. The DAS is provided to fulfill requirements for data collection and monitoring. This document is not an operations procedure or is it intended to describe the mixing operation. This USQ screening provides evaluation of HNF-5572 (Revision 1) including the changes as documented on ECN 654001. The changes include (1) add information on historical trending and data backup, (2) modify DAS I/O list in Appendix E to reflect actual conditions in the field, and (3) delete IP address in Appendix F per Lockheed Martin Services, Inc. request

Effect of mechanical vibrations on the wear behavior of AZ91 Mg alloy

Science.gov (United States)

Chaturvedi, V.; Pandel, U.; Sharma, A.

2018-02-01

AZ91 Mg alloy is the most promising alloy used for structural applications. The vibration induced methods are effective and economic viable in term of mechanical properties. Sliding wear tests were performed on AZ91 Mg alloy using a pin-on- disc configuration. Wear rates were measured at 5 N and 10N at a sliding velocity of 1m/s for varied frequency within the range of 5- 25Hz and a constant amplitude of 2mm. Microstructures of worn surfaces and wear debris were characterized by field emission scanning electron microscopy (FESEM). It is observed that wear resistance of vibrated AZ91 alloy at 15Hz frequency ad 2mm amplitude was superior than cast AZ91 Mg alloy. Finer grain size and equiaxed grain shape both are important parameters for better wear resistance in vibrated AZ91 Mg alloys. FESEM analysis revealed that wear is considerably affected due to frictional heat generated by the relative motion between AZ91 Mg alloy and EN31 steel surface. No single mechanism was responsible for material loss.

Commissioning of Theratron phoenix telecobalt machine and its performance assessment

International Nuclear Information System (INIS)

Rajendran, M.; Reddy, K.D.; Reddy, R.M.; Reddy, J.M.; Reddy, B.V.N.; Kumar, K.; Gopi, S.; Rajan, Dharani; Janardhanan

2002-01-01

Teletherapy machines like cobalt-60 unit and linear accelerator are extensively used for radiotherapy. Theratron phoenix machines have been installed. A brief report on the performance of this machine is presented

Corrosion behaviour and in vitro/in vivo biocompatibility of surface-modified AZ31 alloy; Comportamiento frente a la corrosion y biocompatibilidad in vitrolin vivo de la aleacion AZ31 modificada superficialmente

Energy Technology Data Exchange (ETDEWEB)

Carboneras, M.; Iglesias, C.; Perez-Maceda, B. T.; Valle, J. A. de; Garcia-Alonso, M. C.; Alobera, M. A.; Clemente, C.; Rubio, J. C.; Escudero, M. I.; Lozano, R. M.

2011-07-01

The present work evaluates the corrosion behaviour and the in vitro/in vivo biocompatibility of the AZ31 magnesium alloy, which fulfills the mechanical requirements of bone. The corrosion kinetic of as-received AZ31 alloy was not compatible with the cell growth. To improve its performance, the AZ31 alloy was surface modified by a chemical conversion treatment in hydrofluoric acid. The magnesium fluoride layer generated by the surface treatment of AZ31 alloy enhances its corrosion behaviour, allowing the in vitro growth of osteoblastic cells over the surface and the in vivo formation of a highly compact layer of new bone tissue. These results lead to consider the magnesium fluoride coating as necessary for potential use of the AZ31 alloy as biodegradable and absorbable implant for bone repair. (Author) 18 refs.

Influence of cerium on passivity behavior of wrought AZ91 alloy

International Nuclear Information System (INIS)

Wang Henan; Li Ying; Wang Fuhui

2008-01-01

In this paper, more focus had been put on the passivity behavior of wrought AZ91 alloy with 1.5 mass% Ce. The passive current density of wrought AZ91 alloy increased with addition of Ce and the passive film became unstable. Structures and compositions of the passive films formed on wrought AZ91 alloy without and with Ce in 0.01 M NaOH aqueous solution were analyzed by potentiostatic polarization, potentiostatic-galvanostatic (P-G) transient technique and X-ray photoelectron spectroscopy (XPS). The results showed that Ce only accumulated in the inner layer of passive film in the form of CeO 2 . Further analysis revealed that there were two main effects of Ce on the passive process of wrought AZ91 alloy: first, the existence of CeO 2 in inner layer of passive film made mass transport through the passive film follow tangent hyperbolic (T) impedance instead of Warburg impedance (W); second, donor concentration (N d ) of the passive film increased by a factor 10 when 1.5 mass% Ce existed in wrought AZ91 alloy, which led to the higher passivity current density

77 FR 74457 - Foreign-Trade Zone 75-Phoenix, Arizona Application for Expansion (New Magnet Site) Under...

Science.gov (United States)

2012-12-14

..., Arizona Application for Expansion (New Magnet Site) Under Alternative Site Framework An application has...) adopted by the Board (15 CFR 400.2(c)) to include a new magnet site in Phoenix, Arizona. The application... zone project includes the following magnet sites: Site 1 (338 acres)--within the 550-acre Phoenix Sky...

Effect of aluminum coatings on corrosion properties of AZ31 magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Chiu Liuho; Lin Hsingan; Chen Chunchin; Yang Chihfu [Dept. of materials engineering, Tatung Univ., Taipei (Taiwan); Chang Chiahua; Wu Jenchin [Physical chemistry section, chemical systems research div., Chung-Shan Inst. of Science and Technology, Tao-Yuan (Taiwan)

2003-07-01

This investigation aimed to increase the corrosion resistance of an AZ31 magnesium alloy by an aluminum arc spray coating and a post-treatment consisted of hot pressing and anodizing. It was found that the aluminum arc spraying alone was incapable of protection against corrosion due to the high amount of pores present in the coating layer. In order to solve the problem, densification of the Al arc-sprayed layer was carried out by hot pressing the coated AZ31 Mg alloy plate under an appropriate range of temperature, time and pressure. After hot pressing the Al coated AZ31 Mg alloy plate exhibited a much improved corrosion resistance. A final anodizing treatment applied to the AZ31 alloy with the dense Al coating further improved its resisting to corrosion. The results showed that, by adopting the Al arc spraying, hot pressing and anodizing process, the corrosion current density of the AZ31 alloy in a 3.5 wt% NaCl solution was from 2.1 x 10{sup -6} A/cm{sup 2} (original AZ31) to 3.7 x 10{sup -7} A/cm{sup 2} (after the surface treatment), which value is close to that of an anodized aluminum plate. (orig.)

Microstructure and Aging Behavior of Nonflammable AZ91D Mg Alloy

OpenAIRE

Seok Hong Min; Tae Kwon Ha

2014-01-01

Phase equilibria of AZ91D Mg alloys for nonflammable use, containing Ca and Y, were carried out by using FactSage® and FTLite database, which revealed that solid solution treatment could be performed at temperatures from 400 to 450oC. Solid solution treatment of AZ91D Mg alloy without Ca and Y was successfully conducted at 420oC and supersaturated microstructure with all beta phase resolved into matrix was obtained. In the case of AZ91D Mg alloy with some Ca and Y; howeve...

McMurdo Dry Valleys, Antarctica - A Mars Phoenix Mission Analog

Science.gov (United States)

Tamppari, L. K.; Anderson, R. M.; Archer, D.; Douglas, S.; Kounaves, S. P.; McKay, C. P.; Ming, Douglas W.; Moore, Q.; Quinn, J. E.; Smith, P. H.;

ARSENIC REMOVAL FROM DRINKING WATER BY ADSORPTIVE MEDIA USEPA DEMONSTRATION PROJECT AT VALLEY VISTA, AZ SIX-MONTH EVALUATION REPORT

Science.gov (United States)

This report documents the activities performed and the results obtained from the first six months of the EPA arsenic removal technology demonstration project at the Arizona Water Company (AWC) facility in Sedona, AZ, commonly referred to as Valley Vista. The main objective of the...

Corrosion properties and corrosion evolution of as-cast AZ91 alloy with rare earth yttrium

International Nuclear Information System (INIS)

Luo, T.J.; Yang, Y.S.

2011-01-01

Highlights: → Minor addition of Y will increase the corrosion resistance of AZ91 alloy, and 0.3 wt.% Y is the optimum addition. → A film composed of Mg(OH) 2 , MgCO 3 , Al(OH) 3 and Al 2 O 3 is formed on the surface of AZ91 alloy with rare earth Y free. → The film of AZ91 alloy with 0.3 wt.% Y is mainly composed of Mg(OH) 2 and MgCO 3 without any Al(OH) 3 and Al 2 O 3 . → The relative quantity of MgCO 3 in the surface film of AZ91 + 0.3 wt.% Y is bigger than that of AZ91 alloy with Y free. → Y 2 O 3 phase is found in the surface film of alloy III, which benefits to stabilize the surface film. -- Abstract: The corrosion resistance property and the corrosion evolution of as-cast AZ91 alloy with rare earth Y addition are investigated by using immersion tests, electrochemical impedance spectroscopy (EIS), and X-ray photoelectron spectroscopy (XPS). The results show that the proper amount of Y in the alloys can improve the corrosion resistance of AZ91 alloys effectively. With the increment of Y, the corrosion rate of the modified AZ91 alloys by Y addition was markedly less than that of AZ91 alloy. The corrosion rate of AZ91 alloy with 0.3 wt.% Y was the slightest, but further addition of Y content over 0.3 wt.% make the corrosion heavier. The XPS analysis suggests that the compound film of AZ91 alloy with 0.3 wt.% Y is mainly composed of Mg(OH) 2 and MgCO 3 without any Al(OH) 3 and Al 2 O 3 , in addition, Y 2 O 3 phase is found in the compound film of AZ91 alloy with 0.3 wt.% Y, which benefits to stabilize the surface film.

PHOENIX MARS MECA OPTICAL MICROSCOPE 3 RADIOMETRIC SCI V1.0

Data.gov (United States)

National Aeronautics and Space Administration — The Microscopy, Electrochemistry, and Conductivity Analyzer (MECA) experiment on the Mars Phoenix Lander consists of four instrument components plus command...

702AZ aging waste ventilation facility year 2000 test procedure

International Nuclear Information System (INIS)

Winkelman, W.D.

1998-01-01

This test procedure was developed to determine if the 702AZ Tank Ventilation Facility system is Year 2000 Compliant. The procedure provides detailed instructions for performing the operations necessary and documenting the results. This verification procedure will document that the 702AZ Facility Systems are year 2000 compliant and will correctly meet the criteria established in this procedure

Effect of the chemistry and structure of the native oxide surface film on the corrosion properties of commercial AZ31 and AZ61 alloys

Energy Technology Data Exchange (ETDEWEB)

Feliu, Sebastian, E-mail: sfeliu@cenim.csic.es [Centro Nacional de Investigaciones Metalurgicas CSIC, Avda. Gregorio del Amo 8, 28040 Madrid (Spain); Maffiotte, C. [CIEMAT-DT edificio 30, Avda. Complutense, 22, 28040 Madrid (Spain); Samaniego, A.; Galvan, Juan Carlos [Centro Nacional de Investigaciones Metalurgicas CSIC, Avda. Gregorio del Amo 8, 28040 Madrid (Spain); Barranco, Violeta [Centro Nacional de Investigaciones Metalurgicas CSIC, Avda. Gregorio del Amo 8, 28040 Madrid (Spain); Instituto de Ciencias de Materiales de Madrid, ICMM, Consejo Superior de Investigaciones Cientificas, CSIC, Sor Juana Ines de la Cruz, 3, Cantoblanco, 28049, Madrid (Spain)

2011-08-01

The purpose of this study has been to advance in knowledge of the chemical composition, structure and thickness of the thin native oxide film formed spontaneously in contact with the laboratory atmosphere on the surface of freshly polished commercial AZ31 and AZ61 alloys with a view to furthering the understanding of protection mechanisms. For comparative purposes, and to more fully describe the behaviour of the native oxide film, the external oxide films formed as a result of the manufacturing process (as-received condition) have been characterised. The technique applied in this research to study the thin oxide films (thickness of just a few nanometres) present on the surface of the alloys has basically been XPS (X-ray photoelectron spectroscopy) in combination with ion sputtering. Corrosion properties of the alloys were studied in 0.6 M NaCl by measuring charge transfer resistance values, which are deduced from EIS (electrochemical impedance spectroscopy) measurements after 1 h of exposure. Alloy AZ61 generally showed better corrosion resistance than AZ31, and the freshly polished alloys showed better corrosion resistance than the alloys in as-received condition. This is attributed to a combination of (1) higher thickness of the native oxide film on the AZ61 alloy and (2) greater uniformity of the oxide film in the polished condition. The formation of an additional oxide layer composed by a mixture of spinel (MgAl{sub 2}O{sub 4}) and MgO seems to diminish the protective properties of the passive layer on the surface of the alloys in as-received condition.

Effect of the chemistry and structure of the native oxide surface film on the corrosion properties of commercial AZ31 and AZ61 alloys

International Nuclear Information System (INIS)

Feliu, Sebastian; Maffiotte, C.; Samaniego, A.; Galvan, Juan Carlos; Barranco, Violeta

2011-01-01

The purpose of this study has been to advance in knowledge of the chemical composition, structure and thickness of the thin native oxide film formed spontaneously in contact with the laboratory atmosphere on the surface of freshly polished commercial AZ31 and AZ61 alloys with a view to furthering the understanding of protection mechanisms. For comparative purposes, and to more fully describe the behaviour of the native oxide film, the external oxide films formed as a result of the manufacturing process (as-received condition) have been characterised. The technique applied in this research to study the thin oxide films (thickness of just a few nanometres) present on the surface of the alloys has basically been XPS (X-ray photoelectron spectroscopy) in combination with ion sputtering. Corrosion properties of the alloys were studied in 0.6 M NaCl by measuring charge transfer resistance values, which are deduced from EIS (electrochemical impedance spectroscopy) measurements after 1 h of exposure. Alloy AZ61 generally showed better corrosion resistance than AZ31, and the freshly polished alloys showed better corrosion resistance than the alloys in as-received condition. This is attributed to a combination of (1) higher thickness of the native oxide film on the AZ61 alloy and (2) greater uniformity of the oxide film in the polished condition. The formation of an additional oxide layer composed by a mixture of spinel (MgAl 2 O 4 ) and MgO seems to diminish the protective properties of the passive layer on the surface of the alloys in as-received condition.

CRED REA Coral Population Parameters at Baker, Phoenix Islands, 2004

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Belt transects along 2 consecutively-placed, 25m transect lines were surveyed as part of Rapid Ecological Assessments conducted at 3 sites at Baker in the Phoenix...

76 FR 30299 - Proposed Establishment of Class E Airspace; Kayenta, AZ

Science.gov (United States)

2011-05-25

...-0393; Airspace Docket No. 11-AWP-2] Proposed Establishment of Class E Airspace; Kayenta, AZ AGENCY... action proposes to establish Class E Airspace at Kayenta Airport, Kayenta, AZ. Controlled airspace is...) standard instrument approach procedures at Kayenta Airport. The FAA is proposing this action to enhance the...

The Phoenix galaxy as seen by NuSTAR

DEFF Research Database (Denmark)

Masini, A.; Comastri, A.; Puccetti, S.

2017-01-01

Aims. We study the long-term variability of the well-known Seyfert 2 galaxy Mrk 1210 (also known as UGC 4203, or the Phoenix galaxy). Methods. The source was observed by many X-ray facilities in the last 20 yr. Here we present a NuSTAR observation and put the results in the context of previously ...

Korozní odolnost tvářených hořčíkových slitin AZ31 a AZ61 v Hankovì roztoku

Czech Academy of Sciences Publication Activity Database

Tkacz, J.; Slouková, K.; Minda, J.; Drábiková, J.; Fintová, Stanislava; Doležal, P.; Wasserbauer, J.

2016-01-01

Roč. 60, č. 4 (2016), s. 101-106 ISSN 1804-1213 Institutional support: RVO:68081723 Keywords : corrosion * AZ31 magnesium alloy * AZ61 magnesium alloy Subject RIV: JK - Corrosion ; Surface Treatment of Materials https://www.degruyter.com/view/j/kom.2016.60.issue-4/kom-2016-0016/kom-2016-0016.xml?format=INT

Benchmarking of the PHOENIX-P/ANC [Advanced Nodal Code] advanced nuclear design system

International Nuclear Information System (INIS)

Nguyen, T.Q.; Liu, Y.S.; Durston, C.; Casadei, A.L.

1988-01-01

At Westinghouse, an advanced neutronic methods program was designed to improve the quality of the predictions, enhance flexibility in designing advanced fuel and related products, and improve design lead time. Extensive benchmarking data is presented to demonstrate the accuracy of the Advanced Nodal Code (ANC) and the PHOENIX-P advanced lattice code. Qualification data to demonstrate the accuracy of ANC include comparison of key physics parameters against a fine-mesh diffusion theory code, TORTISE. Benchmarking data to demonstrate the validity of the PHOENIX-P methodologies include comparison of physics predictions against critical experiments, isotopics measurements and measured power distributions from spatial criticals. The accuracy of the PHOENIX-P/ANC Advanced Design System is demonstrated by comparing predictions of hot zero power physics parameters and hot full power core follow against measured data from operating reactors. The excellent performance of this system for a broad range of comparisons establishes the basis for implementation of these tools for core design, licensing and operational follow of PWR [pressurized water reactor] cores at Westinghouse

Differential deposition of H2A.Z in rice seedling tissue during the day-night cycle.

Science.gov (United States)

Zhang, Kang; Xu, Wenying; Wang, Chunchao; Yi, Xin; Su, Zhen

2017-03-04

Chromatin structure has an important role in modulating gene expression. The incorporation of histone variants into the nucleosome leads to important changes in the chromatin structure. The histone variant H2A.Z is highly conserved between different species of fungi, animals, and plants. However, dynamic changes to H2A.Z in rice have not been reported during the day-night cycle. In this study, we generated genome wide maps of H2A.Z for day and night time in harvested seedling tissues by combining chromatin immunoprecipitation and high-throughput sequencing. The analysis results for the H2A.Z data sets detected 7099 genes with higher depositions of H2A.Z in seedling tissues harvested at night compared with seedling tissues harvested during the day, whereas 4597 genes had higher H2A.Z depositions in seedlings harvested during the day. The gene expression profiles data suggested that H2A.Z probably negatively regulated gene expression during the day-night cycle and was involved in many important biologic processes. In general, our results indicated that H2A.Z may play an important role in plant responses to the diurnal oscillation process.

A study on the relationships between corrosion properties and chemistry of thermally oxidised surface films formed on polished commercial magnesium alloys AZ31 and AZ61

Science.gov (United States)

Feliu, Sebastián; Samaniego, Alejandro; Barranco, Violeta; El-Hadad, A. A.; Llorente, Irene; Serra, Carmen; Galván, J. C.

2014-03-01

This paper studies the changes in chemical composition of the thin oxide surface films induced by heating in air at 200 °C for time intervals from 5 min to 60 min on the freshly polished commercial AZ31 and AZ61 alloys with a view to better understanding their protective properties. This thermal treatment resulted in the formation of layers enriched in metallic aluminium at the interface between the outer MgO surface films and the bulk material. A strong link was found between the degree of metallic Al enrichment in the subsurface layer (from 10 to 15 at.%) observed by XPS (X-ray photoelectron spectroscopy) in the AZ61 treated samples and the increase in protective properties observed by EIS (electrochemical impedance spectroscopy) in the immersion test in 0.6 M NaCl. Heating for 5-60 min in air at 200 °C seems to be an effective, easy to perform and inexpensive method for increasing the corrosion resistance of the AZ61 alloy by approximately two or three times.

The A-Z of electronuclear power

International Nuclear Information System (INIS)

Temmerman, G. de; Chedorge, D.

1992-01-01

Both a bilingual translation aid and a reference book, 'The A-Z of Electronuclear Power' covers the full range of electronuclear activities and the English and French terminology relating to the different phases of the modern industrial process

76 FR 3570 - Proposed Amendment of Class E Airspace; Taylor, AZ

Science.gov (United States)

2011-01-20

...-1189; Airspace Docket No. 10-AWP-19] Proposed Amendment of Class E Airspace; Taylor, AZ AGENCY: Federal... proposes to modify Class E airspace at Taylor Airport, Taylor, AZ. Controlled airspace is necessary to accommodate aircraft using the CAMBO One Departure Area Navigation (RNAV) out of Taylor Airport. The FAA is...

75 FR 57327 - Environmental Impact Statement; Pinal County, AZ

Science.gov (United States)

2010-09-20

...: Kenneth H. Davis, Senior Engineering Manager for Operations, Federal Highway Administration, 4000 N... Conservation Service, Federal Aviation Administration, Federal Transit Administration, U.S. Department of... Engineering Manager for Operations, Federal Highway Administration, Arizona Division Office, Phoenix, Arizona...

Cytotoxicity studies of AZ31D alloy and the effects of carbon dioxide on its biodegradation behavior in vitro

Energy Technology Data Exchange (ETDEWEB)

Wang, Jiali, E-mail: wangjialicsu@yahoo.cn [Center for Translational Medicine Research and Development, Institute of Biomedical and Health Engineering, Chinese Academy of Sciences, Shenzhen 518055 (China); Musculoskeletal Research Laboratory, Department of Orthopaedics and Traumatology, The Chinese University of Hong Kong, Hong Kong SAR (China); Qin, Ling [Center for Translational Medicine Research and Development, Institute of Biomedical and Health Engineering, Chinese Academy of Sciences, Shenzhen 518055 (China); Musculoskeletal Research Laboratory, Department of Orthopaedics and Traumatology, The Chinese University of Hong Kong, Hong Kong SAR (China); Wang, Kai [School of Humanities and Social Sciences, Hunan University of Chinese Medicine, Changsha 410208 (China); Wang, Jue; Yue, Ye [Center for Translational Medicine Research and Development, Institute of Biomedical and Health Engineering, Chinese Academy of Sciences, Shenzhen 518055 (China); Li, Yangde [Guangdong Innovation Team for Biodegradable Magnesium and Medical Implants, E-ande, Dongguan 523660 (China); Tang, Jian [Center for Translational Medicine Research and Development, Institute of Biomedical and Health Engineering, Chinese Academy of Sciences, Shenzhen 518055 (China); Li, Weirong [Guangdong Innovation Team for Biodegradable Magnesium and Medical Implants, E-ande, Dongguan 523660 (China)

2013-10-01

Magnesium alloys have been advocated as potential artificial bone materials due to their biocompatibility and biodegradability. The understanding of their corrosive mechanism in physiological environments is therefore essential for making application-orientated designs. Thus, this in vitro study was designed to assess the effects of CO{sub 2} on corrosive behavior of AZ31D to mimic in vivo special ingredient. Electrochemical technologies accompanied with Scanning electron microscope, Fourier transform infrared, X-ray diffraction, Energy dispersive spectroscopy and hydrogen evolution measurement were employed to analyze corrosive rates and mechanisms of AZ31D. Moreover, the biocompatibility of AZ31D was assessed with a direct cell attachment assay and an indirect cytotoxicity test in different diluted extracts. The ion concentrations in extracts were measured using inductively coupled plasma mass spectrometry to offer explanations on the differences of cell viability in the indirect test. The results of the direct cytotoxicity assay showed that the corrosive rate of AZ31D was too rapid to allow for cell adhesion. Extracts diluted less than 20 times would cause adverse effects on cell proliferation, likely due to excessive ions and gas release. Moreover, the presence of CO{sub 2} did not cause significant differences on corrosive behavior of AZ31D according to the results of electrochemical testing and hydrogen evolution measurement. This might be caused by the simultaneous process of precipitation and dissolution of MgCO{sub 3} due to the penetration role of CO{sub 2}. This analysis of corrosive atmospheres on the degradation behavior of magnesium alloys would contribute to the design of more scientific in vitro testing systems in the future. - Highlights: • We evaluate the effects of CO{sub 2} on corrosion behavior of magnesium alloys. • We assess the feasibility of commercial AZ31D alloy as potential implants. • CO{sub 2} is not the key factor to minimize

Electrochemical polymerization of pyrrole over AZ31 Mg alloy for biomedical applications

International Nuclear Information System (INIS)

Srinivasan, A.; Ranjani, P.; Rajendran, N.

2013-01-01

Highlights: ► Polymerization of pyrrole over AZ31 Mg was carried out using cyclic voltammetry. ► Pyrrole concentration was optimized to accomplish the adherent and uniform coating. ► Effect of monomer concentration on the surface morphology was discussed. ► Corrosion resistance of AZ31 Mg in SBF was studied as a function of Py concentration. ► PPy coated AZ31 Mg alloy exhibited enhanced corrosion resistance at 0.25 M of Py. -- Abstract: Electrochemical polymerization of pyrrole (Py) from aqueous salicylate solution over AZ31 Mg alloy was carried out using cyclic voltammetry (CV). The effect of monomer concentration on the surface and electrochemical corrosion in simulated body fluid (SBF) were analysed. Attenuated total reflection-infrared (ATR-IR) spectra showed the characteristic ring stretching peaks for polypyrrole (PPy). Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies exhibited typical cauliflower morphology with rough surface for PPy coated AZ31 Mg alloy. Open circuit potential measurement and potentiodynamic polarization studies revealed that the coating prepared using 0.25 M of Py had positive shift of about 120 mV in corrosion potential and lower corrosion current density (0.03 mA/cm 2 ) compared to other concentrations and uncoated AZ31 Mg alloy (0.25 mA/cm 2 ). Electrochemical impedance spectroscopic (EIS) studies of uncoated and PPy coated Mg alloy in SBF revealed three-time constants behaviour with about one order of increment in impedance value for 0.25 M of Py

Friction welding of AZ31 magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Tsujino, R.; Ochi, H. [Osaka Inst. of Tech., Osaka (Japan); Kawai, G. [Osaka Sangyo Univ., Osaka (Japan); Yamaguchi, H.; Ogawa, K. [Osaka Prefecture Univ., Osaka (Japan); Suga, Y. [Keio Univ., Kanagawa (Japan)

2003-07-01

In this paper, for an acceleration of utilization of magnesium alloy which is being interested in recent years, friction welding of AZ31 magnesium alloy was carried out, and the joint performance was discussed in relation to the deformation heat input in the upset stage and upset loss as a evaluation factor. Where, the deformation heat input in the upset stage is mechanical work represented by the product of upset speed and axial pressure. As a result, it was made clear that the friction welding of AZ31 magnesium alloy was easy in the atmosphere, and good welded joints without a non- adhesion area at the weld interface could de obtained. Moreover, the evaluation factors discussed were possible to evaluate to joint performance. (orig.)

Thermophysical Properties of the Phoenix Mars Landing Site Study Regions

Science.gov (United States)

Putzig, N. E.; Mellon, M. T.; Golombek, M. P.; Arvidson, R. E.

2006-03-01

Analysis of Phoenix Mars study regions places 4 of 5 in a previously-identified duricrust-dominated thermophysical unit which also contains the Viking and Spirit landing sites. Extrapolation of lander-observed properties to the study regions may be complicated by surface heterogeneity.

77 FR 13352 - Notice of Determinations Regarding Eligibility To Apply for Worker Adjustment Assistance

Science.gov (United States)

2012-03-06

.... Services Group, Inc., Corporate/Finance/ Controllers. 81,213 American Express Travel Phoenix, AZ February.... Corporate Resources, Aerotek, Dysis and Tek. 81,254 BT North America, Network Atlanta, GA February 13, 2010... February 7, 2011. Services Group, Inc., Corporate/EIT/Consumer. The following certifications have been...

EVALUATION OF ENDOGENOUS HORMONES AND A XENOBIOTIC PESTICIDE ON SHEEPSHEAD MINNOW GROWTH USING MOLECULAR BIOLOGICAL TECHNIQUES

Science.gov (United States)

Presented at the 131st Annual Meeting of the American Fisheries Society, "2001: A Fisheries Odyssey: The Journey of Science and Education Continues," 19-23 August 2001, Phoenix, AZ. 1 p.We have developed a teleost model to screen physiological effects of endocrine disrup...

77 FR 60969 - Procurement List; Additions

Science.gov (United States)

2012-10-05

... Are Blind or Severely Disabled published a notice for additions to the Procurement List with the... Committee for Purchase From People Who Are Blind or Severely Disabled published notices of proposed..., Phoenix, AZ. Service Type/Location: Custodial and Grounds Maintenance Services, Austin Courthouse, 501...

AZ-101 Mixer Pump Test Qualification Test Procedures (QTP)

International Nuclear Information System (INIS)

THOMAS, W.K.

2000-01-01

Describes the Qualification test procedure for the AZ-101 Mixer Pump Data Acquisition System (DAS). The purpose of this Qualification Test Procedure (QTP) is to confirm that the AZ-101 Mixer Pump System has been properly programmed and hardware configured correctly. This QTP will test the software setpoints for the alarms and also check the wiring configuration from the SIMcart to the HMI. An Acceptance Test Procedure (ATP), similar to this QTP will be performed to test field devices and connections from the field

In Vitro Studies on the Degradability, Bioactivity, and Cell Differentiation of PRP/AZ31B Mg Alloys Composite Scaffold

Directory of Open Access Journals (Sweden)

Jian Zou

2017-01-01

Full Text Available In recent years, more and more methods have been developed to improve the bioactivity of the biodegradable materials in bone tissue regeneration. In present study, we used rat mesenchymal stem cells (rMSCs to evaluate the outcomes of Mg alloys (AZ31B, Magnesium, and Aluminum and Platelet-rich plasma (PRP/Mg alloys on rMSCs biocompatibility and osteogenic differentiation. Water absorption experiments indicated that both bare AZ31B and PRP/AZ31B were capable of absorbing large amounts of water. But the water absorption ratio for PRP/AZ31B was significantly higher than that for bare AZ31B. The degradability experiments implied that both samples degraded at same speed. rMSCs on the surface of AZ31B distributed more and better than those on the AZ31B scaffold. In ALP activity experiment, the activity of rMSCs on the PRP/AZ31B was markedly higher than that on the AZ31B scaffolds on the 7th day and 14th day. qRT-PCR also showed that OPN and OCN were expressed in both samples. OPN and OCN expression in PRP/AZ31B sample were higher than those in bare AZ31B samples. In summary, the in vitro study implied that AZ31B combined with PRP could remarkably improve cell seeding, attachment, proliferation, and differentiation.

The PHOENIX Concept

International Nuclear Information System (INIS)

Van Tuyle, G.J.; Takahashi, H.; Todosow, M.; Aronson, A.L.; Slovik, G.C.; Horak, W.C.

1991-01-01

A proposed means of transmuting key long-lived radioactive isotopes, primarily the so-called minor actinides (Np, Am, Cm), using a hybrid proton-accelerator-sub-critical lattice, is described. It is argued that by partitioning the components of the light water reactor (LWR) spent fuel and by transmuting key elements, such as the plutonium, the minor actinides, and a few of the long-lived fission products, that some of the most significant challenges in building a waste repository can be substantially reduced. If spent fuel partitioning and transmutation were fully implemented, the time required to reduce the waste stream toxicity below that of uranium ore would be reduced from more than 10,000 years to approximately 30 years. The proposed machine, based on the described PHOENIX Concept, would transmute the minor actinides and much of the iodine produced by 75 LWRs, and would generate usable electricity (beyond that required to run the large accelerator) of 850 MW e . 14 refs., 29 figs

Selectividad de caña de azúcar en bovinos

Directory of Open Access Journals (Sweden)

E. M. Aranda

2009-01-01

Full Text Available Se condujo este trabajo con el objetivo de conocer la aceptación del forraje de caña de azúcar integral en la dieta con base de pasto para bovinos adultos fistulados en rumen y duodeno estabulados; para ello, se ofreció pasto estrella africana (Cynodon plectostachyus y caña de azúcar (Saccharum officinarum mezclada con 1% de urea a voluntad, por separado. Se midió la composición de los alimentos, consumo de materia seca, pH ruminal y duodenal. Se utilizaron técnicas de la estadística descriptiva, como la media aritmética y error estándar. La proteína, paredes celulares y hemicelulosa fueron mayores para el pasto estrella. El consumo de MS fue de 46.6 y 38.1% para la caña de azúcar y el pasto, respectivamente; el pH ruminal tuvo valores de 7.3, disminuyendo a 6.7 a las 12 h.; y el pH de la digesta duodenal osciló de 3.7 a 4.7. Se concluye que hubo mayor aceptación por la caña de azúcar y el pH ruminal no indica valores que afecten la celulólisis ruminal.

Comportamiento mecánico de la aleación AZ31 reforzada con nanofibras de carbono

Directory of Open Access Journals (Sweden)

Adeva, P.

2010-12-01

Full Text Available The aim of this study is to investigate the effect of reinforcing AZ31 with carbon nanofibres. The materials AZ31, AZ31-1 % C y AZ31-2 % C were produced by a conventional powder metallurgy route consisting of mechanical mixing of nanofibres and powders of AZ31, cool compactation and extrusion at 350 °C. After extrusion the three materials exhibited a recrystallized microstructure of similar grain size, fine and rather inhomogeneous. Furthermore, they presented a weak fibre texture with basal plane parallel to the extrusion direction. The tensile properties were affected by the nanofibres presence only at 100 °C. At this temperature, yield strength and tensile strength were 30% higher than in the unreinforced alloy.

En este trabajo se ha estudiado el efecto de la adición de nanofibras de carbono en las propiedades mecánicas de la aleación AZ31 procesada por una ruta pulvimetalúrgica convencional. Se prepararon tres materiales, AZ31, AZ31- 1 % C y AZ31-2 % C. Tras una mezcla mecánica de las nanofibras con los polvos de AZ31, se precompactaron en frío y se extruyeron a 350 °C. Los tres presentan una microestructura recristalizada con un tamaño de grano similar, fino aunque algo heterogéneo. Los tres materiales presentan una débil textura de fibra con el plano basal paralelo a la dirección de extrusión. Las propiedades mecánicas a tracción únicamente se ven afectadas por la presencia de nanofibras a 100 °C superando los materiales reforzados en un 30 % a los valores de límite elástico y resistencia de la aleación sin reforzar.

Microstructure and corrosion resistance of Ce–V conversion coating on AZ31 magnesium alloy

International Nuclear Information System (INIS)

Jiang, Xiao; Guo, Ruiguang; Jiang, Shuqin

2015-01-01

Highlights: • Through simple chemical conversion process, a Ce–V conversion coating is prepared on AZ31 magnesium alloy. The coating (∼2 μm thick) has a duplex structure and is composed of Mg, Al, Ce, V and O in the outer layer and Mg, Al, V, F and O in the inner layer. • The Ce–V conversion coating can increase the E corr by 157 mV and decrease the i corr by 80 times compared to AZ31 magnesium alloy substrate. Moreover, the performance of the Ce–V conversion coating excels the chromate conversion coating on AZ31 magnesium alloy. • The EIS results of Ce–V conversion coating indicate an increase of 10× in the corrosion resistance and a delay in the corrosion process kinetics compared to uncoated AZ31 magnesium alloy in 3.5 wt.% NaCl solution. • The ball cratering is a simple and effective technique of thickness measurement for chemical conversion coating. - Abstract: A Ce–V conversion coating was developed to improve the corrosion resistance of AZ31 magnesium alloy. Scanning electronic microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectrometer (XPS), grazing incidence X-ray diffraction (GIXRD) and the ball cratering test were adopted to study the morphology, chemical composition, structure and thickness of the coating. The coating has duplex structure with network and its thickness is about 2 μm. The coating contains high contents of Ce and V, which exhibits amorphous structure. Potentiodynamic polarization shows the coating can increase the corrosion potential and reduce the corrosion current density of AZ31 magnesium alloy. Moreover, the electrochemical impedance spectra exhibit the coating significantly improves the corrosion resistance of AZ31 magnesium alloy. Results indicate that the Ce–V conversion coating can provide effective protection to AZ31 magnesium alloy

Microstructure and corrosion resistance of Ce–V conversion coating on AZ31 magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Jiang, Xiao, E-mail: xiaoxiao217@126.com; Guo, Ruiguang; Jiang, Shuqin

2015-06-30

Highlights: • Through simple chemical conversion process, a Ce–V conversion coating is prepared on AZ31 magnesium alloy. The coating (∼2 μm thick) has a duplex structure and is composed of Mg, Al, Ce, V and O in the outer layer and Mg, Al, V, F and O in the inner layer. • The Ce–V conversion coating can increase the E{sub corr} by 157 mV and decrease the i{sub corr} by 80 times compared to AZ31 magnesium alloy substrate. Moreover, the performance of the Ce–V conversion coating excels the chromate conversion coating on AZ31 magnesium alloy. • The EIS results of Ce–V conversion coating indicate an increase of 10× in the corrosion resistance and a delay in the corrosion process kinetics compared to uncoated AZ31 magnesium alloy in 3.5 wt.% NaCl solution. • The ball cratering is a simple and effective technique of thickness measurement for chemical conversion coating. - Abstract: A Ce–V conversion coating was developed to improve the corrosion resistance of AZ31 magnesium alloy. Scanning electronic microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectrometer (XPS), grazing incidence X-ray diffraction (GIXRD) and the ball cratering test were adopted to study the morphology, chemical composition, structure and thickness of the coating. The coating has duplex structure with network and its thickness is about 2 μm. The coating contains high contents of Ce and V, which exhibits amorphous structure. Potentiodynamic polarization shows the coating can increase the corrosion potential and reduce the corrosion current density of AZ31 magnesium alloy. Moreover, the electrochemical impedance spectra exhibit the coating significantly improves the corrosion resistance of AZ31 magnesium alloy. Results indicate that the Ce–V conversion coating can provide effective protection to AZ31 magnesium alloy.

Gender Roles in Chika Unigwe's The Phoenix | Akani | African ...

African Journals Online (AJOL)

This paper examines gender roles in Chika Unigwe's The Phoenix (2007). In examining these gender roles, the paper focuses on the roles of both female and male genders in the novel in order to tease out issues that border on the marriage institution and gender complementarity in a multicultural setting. As we have ...

Effect of rare earth elements on high cycle fatigue behavior of AZ91 alloy

International Nuclear Information System (INIS)

Mokhtarishirazabad, M.; Boutorabi, S.M.A.; Azadi, M.; Nikravan, M.

2013-01-01

This article investigates effects of adding rare earth elements (RE) into a magnesium–aluminum–zinc alloy (the AZ91 alloy) on its high cycle fatigue (HCF) behavior. For this purpose, AZ91 and AZ91+1% RE (AZE911) alloys were gravity casted in a metallic die. RE elements were added to the AZ91 alloy in the form of mischmetals. Microscopic evaluations with the scanning electron microscopy (SEM) and mechanical tests include tensile, hardness and HCF behaviors, were performed on prepared samples. Rotary bending fatigue tests were carried out at a stress ratio (R) of −1 and a frequency of 125 Hz, at the room temperature, in the air. The microscopic investigation demonstrates that the addition of 1% RE elements leads to the formation of Al 11 RE 3 intermetallic particles which is associated to the reduction of β-(Mg 17 Al 12 ) phases. Results of mechanical experiments suggest a negligible effect of adding 1% RE elements on mechanical properties of the AZ91 alloy. Curves of stress-life (S–N) shows an increase in the fatigue strength at 10 5 cycles, from 100±10 MPa to 135±10 MPa, when RE elements were added to the AZ91 alloy

Effect of rare earth elements on high cycle fatigue behavior of AZ91 alloy

Energy Technology Data Exchange (ETDEWEB)

Mokhtarishirazabad, M., E-mail: mehdi-mokhtari@hotmail.com [School of Metallurgy and Materials Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Boutorabi, S.M.A. [School of Metallurgy and Materials Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Azadi, M.; Nikravan, M. [Irankhodro Powertrain Company (IPCO), Tehran (Iran, Islamic Republic of)

2013-12-10

This article investigates effects of adding rare earth elements (RE) into a magnesium–aluminum–zinc alloy (the AZ91 alloy) on its high cycle fatigue (HCF) behavior. For this purpose, AZ91 and AZ91+1% RE (AZE911) alloys were gravity casted in a metallic die. RE elements were added to the AZ91 alloy in the form of mischmetals. Microscopic evaluations with the scanning electron microscopy (SEM) and mechanical tests include tensile, hardness and HCF behaviors, were performed on prepared samples. Rotary bending fatigue tests were carried out at a stress ratio (R) of −1 and a frequency of 125 Hz, at the room temperature, in the air. The microscopic investigation demonstrates that the addition of 1% RE elements leads to the formation of Al{sub 11}RE{sub 3} intermetallic particles which is associated to the reduction of β-(Mg{sub 17}Al{sub 12}) phases. Results of mechanical experiments suggest a negligible effect of adding 1% RE elements on mechanical properties of the AZ91 alloy. Curves of stress-life (S–N) shows an increase in the fatigue strength at 10{sup 5} cycles, from 100±10 MPa to 135±10 MPa, when RE elements were added to the AZ91 alloy.

Test Excavations at Painted Rock Reservoir: Sites AZ Z:1:7, AZ Z:1:8, and AZ S:16:36.

Science.gov (United States)

1981-11-01

were dehydrated, trimmed to 12-mm squares, and 77 78 placed in catalyzed (0.05-percent benzoyl peroxide), deinhibited acrylic monomer (50-percent methyl ...refrigeration for 72 hours in partially polymerized ethyl- methyl methacrylate. The methacrylate was polymerized at 50 degrees C and 50 p.s.i. nitrogen...pollen types from fill of Feature 10, AZ Z:l:8 Pollen Type Percent Pinus spp. 0.5 Cheno-Am 92.0 Gramineae 2.0 Ambrosia spp. 0.5 Malvaceae 0.5 Zea spp. 2.0

76 FR 54711 - Endangered and Threatened Wildlife and Plants; Bald Eagles Nesting in Sonoran Desert Area of...

Science.gov (United States)

2011-09-02

... Royal Palm Road, Suite 103, Phoenix, AZ 85021; telephone, 602-242-0210; facsimile, 602- 242-2513...)). ``Take'' includes ``pursue, shoot, shoot at, poison, wound, kill, capture, trap, collect, destroy, molest... or in any manner, pursue, hunt, take, capture, kill, attempt to take, capture, or kill, possess...

Analysis of the Deformability of Two-Layer Materials AZ31/Eutectic / Analiza Możliwości Odkształcania Plastycznego Materiału Dwuwarstwowego AZ31/Eutektyka

Directory of Open Access Journals (Sweden)

Mola R.

2015-12-01

Full Text Available The paper present the results of physical simulation of the deformation of the two-layered AZ31/eutectic material using the Gleeble 3800 metallurgical processes simulator. The eutectic layer was produced on the AZ31 substrate using thermochemical treatment. The specimens of AZ31 alloy were heat treated in contact with aluminium powder at 445°C in a vacuum furnace. Depending on the heating time, Al-enriched surface layers with a thickness of 400, 700 and 1100 μm were fabricated on a substrate which was characterized by an eutectic structure composed of the Mg17Al12 phase and a solid solution of aluminium in magnesium. In the study, physical simulation of the fabricated two-layered specimens with a varying thickness of the eutectic layer were deformed using the plane strain compression test at various values of strain rates. The testing results have revealed that it is possible to deform the two-layered AZ31/eutectic material at low strain rates and small deformation values.

Corrosion behaviour of laser surface melted magnesium alloy AZ91D

International Nuclear Information System (INIS)

Taltavull, C.; Torres, B.; Lopez, A.J.; Rodrigo, P.; Otero, E.; Atrens, A.; Rams, J.

2014-01-01

A high power diode laser (HPDL) was used to produce laser surface melting (LSM) treatments on the surface of the Mg alloy AZ91D. Different treatments with different microstructures were produced by varying the laser-beam power and laser-scanning speed. Corrosion evaluation, using hydrogen evolution and electrochemical measurements, led to a relationship between microstructure and corrosion. Most corrosion rates for LSM treated specimens were within the scatter of the as-received AZ91D, whereas some treatments gave higher corrosion rates and some of the samples had corrosion rates lower than the average of the corrosion rate for AZ91D. There were differences in corroded surface morphology. Nevertheless laser treatments introduced surface discontinuities, which masked the effect of the microstructure. Removing these surface defects decreased the corrosion rate for the laser-treated samples. - Highlights: • Corrosion behavior of AZ91D Mg alloys is intimately related with its microstructure. • Laser surface melting treatments allows surface modification of the microstructure. • Different laser parameters can achieve different microstructures. • Controlling laser parameters can produce different corrosion rates and morphologies. • Increase of surface roughness due to laser treatment is relevant to the corrosion rate

Physics Simulations of fluids - a brief overview of Phoenix FD

CERN Multimedia

CERN. Geneva; Nikolov, Svetlin

2014-01-01

The presentation will briefly describe the simulation and rendering of fluids with Phoenix FD, and then proceed into implementation details. We will present our methods of parallelizing the core simulation algorithms and our utilization of the GPU. We will also show how we take advantage of computational fluid dynamics specifics in order to speed up the preview and final rendering, thus achieving a quick pipeline for the creation of various visual effects. About the speakers Ivaylo Iliev is a Senior Software developer at Chaos Group and is the creator of the Phoenix FD simulator for fluid effects. He has a strong interest in physics and has worked on military simulators before focusing on visual effects. He has a Master?s degree from the Varna Technical University. Svetlin Nikolov is a Senior Software developer at Chaos Group with keen interest in physics and artificial intelligence and 7 years of experience in the software industry. He comes from a game development background with a focu...

Effect of ultrasonic cold forging technology as the pretreatment on the corrosion resistance of MAO Ca/P coating on AZ31B Mg alloy

Energy Technology Data Exchange (ETDEWEB)

Chen, Lingling, E-mail: daisy_chenlingling@163.com [College of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617 (China); College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Gu, Yanhong, E-mail: gu_yanhong@163.com [College of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617 (China); Liu, Lu, E-mail: liulu@bipt.edu.cn [College of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617 (China); Liu, Shujing, E-mail: liushujing@bipt.edu.cn [College of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617 (China); Hou, Binbin, E-mail: sohu19880815@126.com [School of Engineering and Technology, China University of Geosciences, Beijing 100083 (China); Liu, Qi, E-mail: 13521196884@sina.cn [College of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617 (China); Ding, Haiyang, E-mail: dinghaiyang@bipt.edu.cn [College of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617 (China)

2015-06-25

Highlights: • Ultrasonic cold forging technology was used as the pretreatment for MAO coating. • Nano layer with the grain size of 30–80 nm was formed on the UCFT treated surface. • Calcium phosphate contained coating was obtained by MAO process. • The remained nano layer underlying MAO coating could impact the corrosion resistance greatly. - Abstract: A calcium phosphate contained (Ca/P) coating was obtained on AZ31B Mg alloy by micro-arc oxidation (MAO) process under the pretreatment of ultrasonic cold forging technology (UCFT). The surface nanograins were introduced after UCFT pretreatment on AZ31B Mg alloy. Optical microscope (OM) was employed to observe the microstructures of the untreated and UCFT treated samples. Transmission electron microscopy (TEM) and atomic force microscope (AFM) were employed to observe the microstructures of nanograins and the surface roughness of the UCFT treated Mg alloys. The grain size of the UCFT treated Mg alloy is 48.67 nm and the surface roughness is 17.03 nm. The microstructures and the phase compositions of MAO samples were observed and analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. The XRD results show that the coating include Ca/P phase, including hydroxyapatite (Ca{sub 10}(PO{sub 4}){sub 6}(OH){sub 2}), HA), tertiary calcium phosphate (Ca{sub 3}(PO{sub 4}){sub 2}, TCP) and calcium phosphate dehydrate (CaHPO{sub 4}⋅2H{sub 2}O, DCPD). The hardness of the samples was measured by the micro-hardness tester under the loads of 10 g, 25 g and 50 g. 3D topographies of hardness indenter were characterized by 3D profiler. The immersion tests and potentiodynamic polarization tests were used to evaluate the weight loss rate and corrosion current density in simulated body fluid (SBF). The results show that the corrosion resistance of Ca/P MAO coating on Mg alloy was improved greatly by the pretreatment of UCFT.

Final results of double-shell tank 241-AZ-101 ultrasonic inspection

International Nuclear Information System (INIS)

JENSEN, C.E.

1999-01-01

This document presents the results and documentation of the nondestructive ultrasonic examination of tank 241-AZ-101. A tank inspection supplier was retained to provide and use an ultrasonic examination system (equipment, procedures, and inspectors) to scan a limited area of double-shell tank 241-AZ-101 primary tank wall and welds. The inspection found one reportable indication of thinning and no reportable pitting, corrosion, or cracking

EnviroAtlas - Phoenix, AZ - Near Road Tree Buffer

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset addresses the tree buffer along heavily traveled roads. The roads are interstates, arterials, and collectors within the EnviroAtlas...

Assessment of genetic diversity for some Iraqi date palms ( Phoenix ...

African Journals Online (AJOL)

Amplified fragment length polymorphisms (AFLP) were used to evaluate the genetic diversity between 18 date palm (Phoenix dactylifera L.) varieties (11 females and 7 males) collected from the center of Iraq. Six primer pairs were applied to detect polymorphism between varieties. A total of 83 polymorphic AFLP fragments ...

A study on the relationships between corrosion properties and chemistry of thermally oxidised surface films formed on polished commercial magnesium alloys AZ31 and AZ61

International Nuclear Information System (INIS)

Feliu, Sebastián; Samaniego, Alejandro; Barranco, Violeta; El-Hadad, A.A.; Llorente, Irene; Serra, Carmen; Galván, J.C.

2014-01-01

Highlights: • Surface chemistry of heat treated magnesium alloys. • Relation between heat treatment and aluminium subsurface enrichment. • Relation between surface composition and corrosion behaviour. - Abstract: This paper studies the changes in chemical composition of the thin oxide surface films induced by heating in air at 200 °C for time intervals from 5 min to 60 min on the freshly polished commercial AZ31 and AZ61 alloys with a view to better understanding their protective properties. This thermal treatment resulted in the formation of layers enriched in metallic aluminium at the interface between the outer MgO surface films and the bulk material. A strong link was found between the degree of metallic Al enrichment in the subsurface layer (from 10 to 15 at.%) observed by XPS (X-ray photoelectron spectroscopy) in the AZ61 treated samples and the increase in protective properties observed by EIS (electrochemical impedance spectroscopy) in the immersion test in 0.6 M NaCl. Heating for 5–60 min in air at 200 °C seems to be an effective, easy to perform and inexpensive method for increasing the corrosion resistance of the AZ61 alloy by approximately two or three times

A study on the relationships between corrosion properties and chemistry of thermally oxidised surface films formed on polished commercial magnesium alloys AZ31 and AZ61

Energy Technology Data Exchange (ETDEWEB)

Feliu, Sebastián, E-mail: sfeliu@cenim.csic.es [Centro Nacional de Investigaciones Metalúrgicas CSIC, Avda. Gregorio del Amo 8, 28040 Madrid (Spain); Samaniego, Alejandro [Centro Nacional de Investigaciones Metalúrgicas CSIC, Avda. Gregorio del Amo 8, 28040 Madrid (Spain); Barranco, Violeta [Instituto de Ciencias de Materiales de Madrid, ICMM, Consejo Superior de Investigaciones Científicas, CSIC, Sor Juana Inés de la Cruz, 3, Cantoblanco, 28049, Madrid (Spain); El-Hadad, A.A. [Physics Department, Faculty of Science, Al-Azhar University, Nasr City 11884, Cairo (Egypt); Llorente, Irene [Centro Nacional de Investigaciones Metalúrgicas CSIC, Avda. Gregorio del Amo 8, 28040 Madrid (Spain); Serra, Carmen [Servicio de Nanotecnologia y Análisis de Superficies, CACTI, Universidade de Vigo, 36310 Vigo (Spain); Galván, J.C. [Centro Nacional de Investigaciones Metalúrgicas CSIC, Avda. Gregorio del Amo 8, 28040 Madrid (Spain)

2014-03-01

Highlights: • Surface chemistry of heat treated magnesium alloys. • Relation between heat treatment and aluminium subsurface enrichment. • Relation between surface composition and corrosion behaviour. - Abstract: This paper studies the changes in chemical composition of the thin oxide surface films induced by heating in air at 200 °C for time intervals from 5 min to 60 min on the freshly polished commercial AZ31 and AZ61 alloys with a view to better understanding their protective properties. This thermal treatment resulted in the formation of layers enriched in metallic aluminium at the interface between the outer MgO surface films and the bulk material. A strong link was found between the degree of metallic Al enrichment in the subsurface layer (from 10 to 15 at.%) observed by XPS (X-ray photoelectron spectroscopy) in the AZ61 treated samples and the increase in protective properties observed by EIS (electrochemical impedance spectroscopy) in the immersion test in 0.6 M NaCl. Heating for 5–60 min in air at 200 °C seems to be an effective, easy to perform and inexpensive method for increasing the corrosion resistance of the AZ61 alloy by approximately two or three times.

Biodegradable behaviors of AZ31 magnesium alloy in simulated body fluid

International Nuclear Information System (INIS)

Song Yingwei; Shan Dayong; Chen Rongshi; Zhang Fan; Han Enhou

2009-01-01

Magnesium alloys have unique advantages to act as biodegradable implants for clinical application. The biodegradable behaviors of AZ31 in simulated body fluid (SBF) for various immersion time intervals were investigated by electrochemical impedance spectroscopy (EIS) tests and scanning electron microscope (SEM) observation, and then the biodegradable mechanisms were discussed. It was found that a protective film layer was formed on the surface of AZ31 in SBF. With increasing of immersion time, the film layer became more compact. If the immersion time was more than 24 h, the film layer began to degenerate and emerge corrosion pits. In the meantime, there was hydroxyapatite particles deposited on the film layer. The hydroxyapatite is the essential component of human bone, which indicates the perfect biocompatibility of AZ31 magnesium alloy.

Study on fused/cast AZS refractories for deployment in vitrification of radioactive waste effluents

Energy Technology Data Exchange (ETDEWEB)

Sengupta, Pranesh, E-mail: praneshsengupta@gmail.com [Materials Science Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Mishra, R.K.; Soudamini, N. [Waste Management Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Sen, D.; Mazumder, S. [Solid State Physics Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Kaushik, C.P. [Waste Management Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Ajithkumar, T.G. [Central NMR Facility, National Chemical Laboratory, Pune 411 008 (India); Banerjee, K. [Nuclear Recycle Group, Mumbai 400 085 (India)

2015-12-15

‘Fused/cast Al{sub 2}O{sub 3}–ZrO{sub 2}–SiO{sub 2} (FC-AZS)’ is being considered as ‘glass contact refractory’ within ceramic melters, to be used for nuclear waste immobilization. Microstructural analyses reveal random distributions of baddeleyite (ZrO{sub 2}) within aluminosilicate (Al{sub 2}SiO{sub 5}) matrix. {sup 27}Al and {sup 29}Si NMR data suggest that within aluminosilicate matrix Al occurs in both 4- and 6-fold co-ordinations whereas Si prefers a 4-fold environment. Polydispersity of pores has been studied with small-angle neutron scattering (SANS) technique. Corrosion rates of FC-AZS within 6 M HNO{sub 3}, simulated wastes (500 h exposure), and borosilicate melt (975 °C, 800 h exposure) are found to be 0.38 × 10{sup 3} μmy{sup −1}, 0.13 × 10{sup 3} μmy{sup −1} and 4.75 × 10{sup 3} μmy{sup −1} respectively. A comparison of chemical interaction data clearly suggests that FC-AZS exhibits better chemical durability than AZC refractory (Al{sub 2}O{sub 3}–ZrO{sub 2}–Cr{sub 2}O{sub 3}, also used for similar purpose). Thermal cycling studies indicate that FC-AZS retains structural integrity (including compressive strength and density) even up to 20 cycles. - Highlights: • Vitrification of nuclear waste using AZS refractory within ceramic melter. • Microstructure of AZS refractory. • Interaction of AZS with simulated high level waste and glass.

Phoenix type concepts for transmutation of LWR waste minor actinides

International Nuclear Information System (INIS)

Segev, M.

1994-01-01

A number of variations on the original Phoenix theme were studied. The basic rationale of the Phoenix incinerator is making oxide fuel of the LWR waste minor actinides, loading it in an FFTF-like subcritical core, then bombarding the core with the high current beam accelerated protons to generate considerable energy through spallation and fission reactions. As originally assessed, if the machine is fed with 1600 MeV protons in a 102 mA current, then 8 core modules are driven to transmute the yearly minor actinides waste of 75 1000 MW LWRs into Pu 238 and fission products; in a 2 years cycle the energy extracted is 100000 MW d/T. This performance cannot be substantiated in a rigorous analysis. A calculational consistent methodology, based on a combined execution of the Hermes, NCNP, and Korigen codes, shows, nonetheless that changes in the original Phoenix parameters can upgrade its performance.The original Phoenix contains 26 tons minor actinides in 8 core modules; 1.15 m 3 module is shaped for 40% neutron leakage; with a beam of 102 mA the 8 modules are driven to 100000 MW/T in 10.5 years, burning out the yearly minor actinide waste of 15 LWRs; the operation must be assisted by grid electricity. If the 1.15 m 3 module is shaped to allow only 28% leakage, then a beam of 102 mA will drive the 8 modules to 100000 MW/T in 3.5 years, burning out the yearly minor actinides waste of 45 LWRs. Some net grid electricity will be generated. If 25 tons minor actinides are loaded into 5 modules, each 1.72 m 3 in volume and of 24% leakage, then a 97 mA beam will drive the module to 100000 MW/T in 2.5 years, burning out the yearly minor actinides waste of 70 LWRs. A considerable amount of net grid electricity will be generated. If the lattice is made of metal fuel, and 26 tons minor actinides are loaded into 32 small modules, 0.17 m 3 each, then a 102 mA beam will drive the modules to 100000 MW/T in 2 years, burning out the yearly minor actinides waste of 72 LWRs. A considerable

Ethnobotanical survey of Phoenix dactylifera L. Pollen used for the ...

African Journals Online (AJOL)

Background: The Phoenix dactylifera L. (date palm) is known for its traditional medicinal properties across the history of native population in Algerian Sahara. There is a large trend of consumption of date palm pollen preparations in many human infertility cases in our country. However, the validity has not been scientifically ...

CESIUM REMOVAL FROM TANKS 241-AN-103 & 241-SX-105 & 241-AZ-101 & 241AZ-102 COMPOSITE FOR TESTING IN BENCH SCALE STEAM REFORMER

Energy Technology Data Exchange (ETDEWEB)

DUNCAN JB; HUBER HJ

2011-04-21

This report documents the preparation of three actual Hanford tank waste samples for shipment to the Savannah River National Laboratory (SRNL). Two of the samples were dissolved saltcakes from tank 241-AN-103 (hereafter AN-103) and tank 241-SX-105 (hereafter SX-105); one sample was a supernate composite from tanks 241-AZ-101 and 241-AZ-102 (hereafter AZ-101/102). The preparation of the samples was executed following the test plans LAB-PLAN-10-00006, Test Plan for the Preparation of Samples from Hanford Tanks 241-SX-105, 241-AN-103, 241-AN-107, and LAB-PLN-l0-00014, Test Plan for the Preparation of a Composite Sample from Hanford Tanks 241-AZ-101 and 241-AZ-102 for Steam Reformer Testing at the Savannah River National Laboratory. All procedural steps were recorded in laboratory notebook HNF-N-274 3. Sample breakdown diagrams for AN-103 and SX-105 are presented in Appendix A. The tank samples were prepared in support of a series of treatability studies of the Fluidized Bed Steam Reforming (FBSR) process using a Bench-Scale Reformer (BSR) at SRNL. Tests with simulants have shown that the FBSR mineralized waste form is comparable to low-activity waste glass with respect to environmental durability (WSRC-STI-2008-00268, Mineralization of Radioactive Wastes by Fluidized Bed Steam Reforming (FBSR): Comparisons to Vitreous Waste Forms and Pertinent Durability Testing). However, a rigorous assessment requires long-term performance data from FBSR product formed from actual Hanford tank waste. Washington River Protection Solutions, LLC (WRPS) has initiated a Waste Form Qualification Program (WP-5.2.1-2010-001, Fluidized Bed Steam Reformer Low-level Waste Form Qualification) to gather the data required to demonstrate that an adequate FBSR mineralized waste form can be produced. The documentation of the selection process of the three tank samples has been separately reported in RPP-48824, Sample Selection Process for Bench-Scale Steam Reforming Treatability Studies Using

The Flight of the Phoenix: Interpersonal Aspects of Project Management

Science.gov (United States)

Huffman, Brian J.; Kilian, Claire McCarty

2012-01-01

Although many classroom exercises use movies to focus on management and organizational behavior issues, none of those do so in the context of project management. This article presents such an exercise using "The Flight of the Phoenix", an incredibly rich story for any management class, which provides clear examples of organizational behavior…

A two-step superplastic forging forming of semi-continuously cast AZ70 magnesium alloy

Directory of Open Access Journals (Sweden)

Pan Wang

2015-03-01

Full Text Available A two-step technology combined forging with superplastic forming has been developed to enhance the forgeability of semi-continuously cast AZ70 magnesium alloy and realize the application of the as-cast magnesium alloy in large deformation bullet shell. In the first step, fine-grained microstructure preforms that are suitable for superplastic forming were obtained by reasonably designing the size of the initial blanks with the specific height-to-diameter ratio, upsetting the blanks and subsequent annealing. In the second step, the heat treated preforms were forged into the end products at the superplastic conditions. The end products exhibit high quality surface and satisfied microstructure. Consequently, this forming technology that not only avoids complicating the material preparation but also utilizes higher strain rate superplastic provides a near net-shaped novel method on magnesium forging forming technology using as-cast billet.

Operational Test Report for the 241-AZ-101 Suspended Solids Profiler

International Nuclear Information System (INIS)

STENKAMP, D.M.

2000-01-01

This document comprises the Operational Test Report for the 241-AZ-101 Suspended Solids Profiler. This document presents the results of Operational Testing of the 241-AZ-101 Suspended Solids Profiler (SSP). Testing of the SSP was performed in accordance with OTP-260-005, ''SUSPENDED SOLIDS PROFILER OPERATIONAL TEST PROCEDURE''. The objective of the testing was to verify that all equipment and components functioned as designed, following construction completion and turnover to operations

Effects of the Phoenix Lander descent thruster plume on the Martian surface

Science.gov (United States)

Plemmons, D. H.; Mehta, M.; Clark, B. C.; Kounaves, S. P.; Peach, L. L.; Renno, N. O.; Tamppari, L.; Young, S. M. M.

2008-08-01

The exhaust plume of Phoenix's hydrazine monopropellant pulsed descent thrusters will impact the surface of Mars during its descent and landing phase in the northern polar region. Experimental and computational studies have been performed to characterize the chemical compounds in the thruster exhausts. No undecomposed hydrazine is observed above the instrument detection limit of 0.2%. Forty-five percent ammonia is measured in the exhaust at steady state. Water vapor is observed at a level of 0.25%, consistent with fuel purity analysis results. Moreover, the dynamic interactions of the thruster plumes with the ground have been studied. Large pressure overshoots are produced at the ground during the ramp-up and ramp-down phases of the duty cycle of Phoenix's pulsed engines. These pressure overshoots are superimposed on the 10 Hz quasi-steady ground pressure perturbations with amplitude of about 5 kPa (at touchdown altitude) and have a maximum amplitude of about 20-40 kPa. A theoretical explanation for the physics that causes these pressure perturbations is briefly described in this article. The potential for soil erosion and uplifting at the landing site is also discussed. The objectives of the research described in this article are to provide empirical and theoretical data for the Phoenix Science Team to mitigate any potential problem. The data will also be used to ensure proper interpretation of the results from on-board scientific instrumentation when Martian soil samples are analyzed.

Corrosion and mechanical performance of AZ91 exposed to simulated inflammatory conditions.

Science.gov (United States)

Brooks, Emily K; Der, Stephanie; Ehrensberger, Mark T

2016-03-01

Magnesium (Mg) and its alloys, including Mg-9%Al-1%Zn (AZ91), are biodegradable metals with potential use as temporary orthopedic implants. Invasive orthopedic procedures can provoke an inflammatory response that produces hydrogen peroxide (H2O2) and an acidic environment near the implant. This study assessed the influence of inflammation on both the corrosion and mechanical properties of AZ91. The AZ91 samples in the inflammatory protocol were immersed for three days in a complex biologically relevant electrolyte (AMEM culture media) that contained serum proteins (FBS), 150 mM of H2O2, and was titrated to a pH of 5. The control protocol immersed AZ91 samples in the same biologically relevant electrolyte (AMEM & FBS) but without H2O2 and the acid titration. After 3 days all samples were switched into fresh AMEM & FBS for an additional 3-day immersion. During the initial immersion, inflammatory protocol samples showed increased corrosion rate determined by mass loss testing, increased Mg and Al ion released to solution, and a completely corroded surface morphology as compared to the control protocol. Although corrosion in both protocols slowed once the test electrolyte solution was replaced at 3 days, the samples originally exposed to the simulated inflammatory conditions continued to display enhanced corrosion rates as compared to the control protocol. These lingering effects may indicate the initial inflammatory corrosion processes modified components of the surface oxide and corrosion film or initiated aggressive localized processes that subsequently left the interface more vulnerable to continued enhanced corrosion. The electrochemical properties of the interfaces were also evaluated by EIS, which found that the corrosion characteristics of the AZ91 samples were potentially influenced by the role of intermediate adsorption layer processes. The increased corrosion observed for the inflammatory protocol did not affect the flexural mechanical properties of the AZ91

The Thermal Electrical Conductivity Probe (TECP) for Phoenix

Science.gov (United States)

Zent, Aaron P.; Hecht, Michael H.; Cobos, Doug R.; Campbell, Gaylon S.; Campbell, Colin S.; Cardell, Greg; Foote, Marc C.; Wood, Stephen E.; Mehta, Manish

2009-01-01

The Thermal and Electrical Conductivity Probe (TECP) is a component of the Microscopy, Electrochemistry, and Conductivity Analyzer (MECA) payload on the Phoenix Lander. TECP will measure the temperature, thermal conductivity and volumetric heat capacity of the regolith. It will also detect and quantify the population of mobile H2O molecules in the regolith, if any, throughout the polar summer, by measuring the electrical conductivity of the regolith, as well as the dielectric permittivity. In the vapor phase, TECP is capable of measuring the atmospheric H2O vapor abundance, as well as augment the wind velocity measurements from the meteorology instrumentation. TECP is mounted near the end of the 2.3 m Robotic Arm, and can be placed either in the regolith material or held aloft in the atmosphere. This paper describes the development and calibration of the TECP. In addition, substantial characterization of the instrument has been conducted to identify behavioral characteristics that might affect landed surface operations. The greatest potential issue identified in characterization tests is the extraordinary sensitivity of the TECP to placement. Small gaps alter the contact between the TECP and regolith, complicating data interpretation. Testing with the Phoenix Robotic Arm identified mitigation techniques that will be implemented during flight. A flight model of the instrument was also field tested in the Antarctic Dry Valleys during the 2007-2008 International Polar year. 2

Tank 241-AZ-101 Mixer Pump Test Vapor Sampling and Analysis Plan

International Nuclear Information System (INIS)

TEMPLETON, A.M.

2000-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for vapor samples obtained during the operation of mixer pumps in tank 241-AZ-101. The primary purpose of the mixer pump test (MPT) is to demonstrate that the two 300 horsepower mixer pumps installed in tank 241-AZ-101 can mobilize the settled sludge so that it can be retrieved for treatment and vitrification. Sampling will be performed in accordance with Tank 241-AZ-101 Mixer Pump Test Data Quality Objective (Banning 1999) and Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis (Mulkey 1999). The sampling will verify if current air emission estimates used in the permit application are correct and provide information for future air permit applications

Microstructures of friction welded joints of AZ31 to AM60 magnesium alloys

Energy Technology Data Exchange (ETDEWEB)

Fukumoto, S.; Ono, T.; Tanaka, S.; Tsubakino, H. [Graduate School of Engineering, Himeji Inst. of Tech., Hyogo (Japan); Tomita, T.; Aritoshi, M. [Hyogo Prefectural Inst. of Industrial Research, Kobe, Hyogo (Japan); Okita, K. [Inst. of Industrial Research, Osaka Sangyo Univ., Osaka (Japan)

2003-07-01

AZ31 magnesium alloy was friction-welded to AM60 and the microstructures and the friction welding process were studied. The microstructures changed near the weld interface. The AZ31 was refined to a grain size of several {mu}m near the weld interface. The nucleation occurred in the shear bands that were introduced during the welding process. On the other hand, the eutectic structure was deformed and the lamellar structure which was composed of {alpha}-Mg and Mg{sub 17}Al{sub 12} was formed near the weld interface in AM60 alloy. In the friction process, the adhesion and peel off occurred alternately between AZ31 and AM60. Eventually, bonding was completed during upset process. (orig.)

Influencia de compuestos azúcares y no azúcares en la calidad industrial de caña de azúcar en Tucumán (R. Argentina: Parte 1: caña limpia y despuntada Influence of sugar and nonsugar compounds on sugarcane industrial quality in Tucumán (Argentine Republic

Directory of Open Access Journals (Sweden)

B. Silvia Zossi

Full Text Available Se estudió la concentración de compuestos azúcares y no azúcares, especialmente los que influyen en la formación del color y otros que inciden en el proceso industrial de producción de azúcar blanco directo, de las cuatro variedades comerciales de caña más difundidas en Tucumán (R. Argentina: TUCCP 77-42, LCP 85-384, CP 65-357 y RA 87-3. Estos ensayos fueron realizados durante las zafras 2004 a 2007 en caña limpia y despuntada. Los parámetros analizados fueron: extracción de jugo, Brix %, pol % en jugo y en caña, sacarosa y azúcar recuperable. Se estudiaron no azúcares inorgánicos, tales como cenizas, fosfato y sílice, y no azúcares orgánicos: fibra, almidón, compuestos antocianos y fenoles, nitrógeno amínico, ácidos cis y trans-aconítico, "indicator value" y color. De las cuatro variedades analizadas, la que mejor comportamiento presentó para producir azúcar blanco directo fue LCP 85-384, por su alto contenido en sacarosa y bajo contenido de componentes no azúcares. El segundo lugar le correspondió a la variedad RA 87-3, seguida por CP 65-357 y TUCCP 77-42.The concentration of sugar and nonsugar compounds, especially those which play a part in colour formation and others which affect direct white sugar manufacturing process, was studied in the four commercial cane varieties most widely grown in Tucumán (Argentine Republic: TUCCP 77-42, LCP 85-384, CP 65-357 and RA 87-3. Trials with clean cane were conducted during the 2004-2007 harvests. Analyzed parameters were: juice extraction, Brix %, pol % in juice and cane, sucrose and sugar recovery. Inorganic nonsugar compounds, such as ash, phosphate and silica, as well as organic ones, such as fibre, starch, anthocyanin and phenolic compounds, amino nitrogen, cis and trans-aconitic acids, indicator value and colour, were studied. Results showed that LCP 85-384 variety had the best factory performance to produce direct white sugar because of its high sucrose and low

78 FR 30392 - Notice of Application for Special Permits

Science.gov (United States)

2013-05-22

...). 15860-N Apple Inc., 49 CFR 173.185(a).... To authorize the Cupertino, CA. transportation in commerce of..., 3, 4, 5). 15853-N Praxair, Inc., 49 CFR 176.83........ To authorize the Danbury, CT. transportation.......... To authorize the Inc., Phoenix, AZ. transportation in commerce of certain DOT 3AL cylinders that are...

Survey of intestinal parasitism in dogs in the Phoenix metropolitan area.

Science.gov (United States)

Cornell, Heather N; O'Neal, Peter R; Wong, Valerie M; Noah, Donald L

2017-09-01

OBJECTIVE To determine the prevalence of selected intestinal parasites in pet dogs and recently apprehended free-roaming (AFR) shelter dogs in the Phoenix metropolitan area and compare those prevalences between the 2 groups. DESIGN Cross-sectional study. SAMPLE Convenience samples of fecal specimens from owned pet dogs from the Phoenix metropolitan area (n = 175) and free-roaming dogs apprehended and admitted to Maricopa County Animal Care and Control and Arizona Humane Society facilities from November 2014 through March 2015 (188). PROCEDURES Fresh fecal specimens were collected from all dogs; for AFR shelter dogs, specimens were collected within 72 hours after facility admission. Standard centrifugal flotation tests and an ELISA were performed to detect 5 common intestinal parasites (roundworms, hookworms, whipworms, Giardia spp, and Cystoisospora spp). Group comparisons were performed by means of the χ 2 test and Rogan-Gladen prevalence estimate. RESULTS At least 1 of the 5 evaluated parasites was detected in 85 (45.2%) fecal specimens from AFR shelter dogs and 24 (13.7%) specimens from owned pet dogs. This prevalence differed significantly between the groups. Notably, the prevalence of Giardia spp in AFR shelter dogs (n = 76 [40.4%]) was higher than previously reported in the United States. CONCLUSIONS AND CLINICAL RELEVANCE The prevalence of the evaluated intestinal parasites, particularly of Giardia spp, in AFR shelter dogs was higher than expected. This information is important for veterinarians, animal shelter personnel, pet owners, human health-care providers, and public health officials to consider when devising effective interventions and risk communication efforts against potential zoonotic threats, particularly those relevant to the Phoenix metropolitan area.

Characterization of the first core sample of neutralized current acid waste from double-shell tank 101-AZ

International Nuclear Information System (INIS)

Peterson, M.E.; Scheele, R.D.; Tingey, J.M.

1989-09-01

In FY 1989, Westinghouse Hanford Company (WHC) successfully obtained four core samples (totaling seven segments) of neutralized current acid waste (NCAW) from double-shell tanks (DSTs) 101-AZ and 102-AZ. A segment was a 19-in.-long and 1-in.-diameter cylindrical sample of waste. A core sample consisted of enough 19-in.-long segments to obtain the waste of interest. Three core samples were obtained from DST 101-AZ and one core sample from DST 102-AZ. Two DST 101-AZ core samples consisted of two segments per core, and the third core sample consisted of only one segment. The third core consisted of the solids from the bottom of the tank and was used to determine the relative abrasiveness of this NCAW. The DST 102-AZ core sample consisted of two segments. The core samples were transported to the Pacific Northwest Laboratory (PNL), where the waste was extruded from its sampler and extensively characterized. A characterization plan was followed that simulated the processing of the NCAW samples through retrieval, pretreatment and vitrification process steps. Physical, rheological, chemical and radiochemical properties were measured throughout the process steps. The characterization of the first core sample from DST 101-AZ was completed, and the results are provided in this report. The results for the other core characterizations will be reported in future reports. 3 refs., 13 figs., 10 tabs

Characteristics of AZ31 Mg alloy joint using automatic TIG welding

Science.gov (United States)

Liu, Hong-tao; Zhou, Ji-xue; Zhao, Dong-qing; Liu, Yun-teng; Wu, Jian-hua; Yang, Yuan-sheng; Ma, Bai-chang; Zhuang, Hai-hua

2017-01-01

The automatic tungsten-inert gas welding (ATIGW) of AZ31 Mg alloys was performed using a six-axis robot. The evolution of the microstructure and texture of the AZ31 auto-welded joints was studied by optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and electron backscatter diffraction. The ATIGW process resulted in coarse recrystallized grains in the heat affected zone (HAZ) and epitaxial growth of columnar grains in the fusion zone (FZ). Substantial changes of texture between the base material (BM) and the FZ were detected. The {0002} basal plane in the BM was largely parallel to the sheet rolling plane, whereas the c-axis of the crystal lattice in the FZ inclined approximately 25° with respect to the welding direction. The maximum pole density increased from 9.45 in the BM to 12.9 in the FZ. The microhardness distribution, tensile properties, and fracture features of the AZ31 auto-welded joints were also investigated.

Microstructure and corrosion behavior of electrodeposited nano-crystalline nickel coating on AZ91 Mg alloy

Energy Technology Data Exchange (ETDEWEB)

Zarebidaki, Arman, E-mail: arman.zare@iauyazd.ac.ir; Mahmoudikohani, Hassan, E-mail: hassanmahmoudi.k@gmail.com; Aboutalebi, Mohammad-Reza

2014-12-05

Highlights: • Activation, zincating, and Cu electrodeposition were used as pretreatment processes for electrodeposition of nickel coatings. • Nano-crystalline nickel coatings were successfully electrodeposited onto the AZ91 Mg alloys. • Effect of nickel electrodeposited coating on the corrosion resistance of AZ91 Mg alloy has been studied. - Abstract: In order to enhance the corrosion resistance, nickel coating was electrodeposited onto AZ91 Mg alloy. Activation, zincating, and Cu electrodeposition used as pretreatment processes for better adhesion and corrosion performance of the nickel over layer. The corrosion properties of the AZ91 Mg alloy, nickel electroplated AZ91 Mg alloy, and pure nickel was assessed via polarization and electrochemical impedance spectroscopy (EIS) methods in 3.5 wt% NaCl solution. Moreover, the structure of the coating was investigated by means of X-ray diffraction, whereas specimen’s morphology and elemental composition were analyzed using scanning electron microscope (SEM) equipped with energy dispersive spectrometer (EDS). Measurements revealed that the coating has a nano-crystalline structure with the grain size of 95 nm. Corrosion results showed superior corrosion resistance for the coated AZ91 Mg alloy as the corrosion current density decreased from 2.5 × 10{sup −4} A cm{sup −2}, for the uncoated sample, to 1.5 × 10{sup −5} A cm{sup −2}, for coated specimen and the corrosion potential increased from −1.55 V to −0.98 V (vs. Ag/AgCl) at the same condition.

Cost and Potential of Monolithic CIGS Photovoltaic Modules

Energy Technology Data Exchange (ETDEWEB)

Horowitz, Kelsey; Woodhouse, Michael

2015-06-17

A bottom-up cost analysis of monolithic, glass-glass Cu(In,Ga)(Se,S)2 (CIGS) modules is presented, illuminating current cost drivers for this technology and possible pathways to reduced cost. At 14% module efficiency, for the case of U.S. manufacturing, a manufacturing cost of $0.56/WDC and a minimum sustainable price of $0.72/WDC were calculated. Potential for reduction in manufacturing costs to below $0.40/WDC in the long-term may be possible if module efficiency can be increased without significant increase in $/m2 costs. The levelized cost of energy (LCOE) in Phoenix, AZ under different conditions is assessed and compared to standard c-Si.

Morning Frost in Trench Dug by Phoenix, Sol 113

Science.gov (United States)

2008-01-01

This image from the Surface Stereo Imager on NASA's Phoenix Mars Lander shows morning frost inside the 'Snow White' trench dug by the lander, in addition to subsurface ice exposed by use of a rasp on the floor of the trench. The camera took this image at about 9 a.m. local solar time during the 113th Martian day of the mission (Sept. 18, 2008). Bright material near and below the four-by-four set of rasp holes in the upper half of the image is water-ice exposed by rasping and scraping in the trench earlier the same morning. Other bright material especially around the edges of the trench, is frost. Earlier in the mission, when the sun stayed above the horizon all night, morning frost was not evident in the trench. This image is presented in approximately true color. The trench is 4 to 5 centimeters (about 2 inches) deep, about 23 centimeters (9 inches) wide. Phoenix landed on a Martian arctic plain on May 25, 2008. The mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is led by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development was by Lockheed Martin Space Systems, Denver.

Expression of P. falciparum var Genes Involves Exchange of the Histone Variant H2A.Z at the Promoter

Science.gov (United States)

Petter, Michaela; Lee, Chin Chin; Byrne, Timothy J.; Boysen, Katja E.; Volz, Jennifer; Ralph, Stuart A.; Cowman, Alan F.; Brown, Graham V.; Duffy, Michael F.

2011-01-01

Plasmodium falciparum employs antigenic variation to evade the human immune response by switching the expression of different variant surface antigens encoded by the var gene family. Epigenetic mechanisms including histone modifications and sub-nuclear compartmentalization contribute to transcriptional regulation in the malaria parasite, in particular to control antigenic variation. Another mechanism of epigenetic control is the exchange of canonical histones with alternative variants to generate functionally specialized chromatin domains. Here we demonstrate that the alternative histone PfH2A.Z is associated with the epigenetic regulation of var genes. In many eukaryotic organisms the histone variant H2A.Z mediates an open chromatin structure at promoters and facilitates diverse levels of regulation, including transcriptional activation. Throughout the asexual, intraerythrocytic lifecycle of P. falciparum we found that the P. falciparum ortholog of H2A.Z (PfH2A.Z) colocalizes with histone modifications that are characteristic of transcriptionally-permissive euchromatin, but not with markers of heterochromatin. Consistent with this finding, antibodies to PfH2A.Z co-precipitate the permissive modification H3K4me3. By chromatin-immunoprecipitation we show that PfH2A.Z is enriched in nucleosomes around the transcription start site (TSS) in both transcriptionally active and silent stage-specific genes. In var genes, however, PfH2A.Z is enriched at the TSS only during active transcription in ring stage parasites. Thus, in contrast to other genes, temporal var gene regulation involves histone variant exchange at promoter nucleosomes. Sir2 histone deacetylases are important for var gene silencing and their yeast ortholog antagonises H2A.Z function in subtelomeric yeast genes. In immature P. falciparum parasites lacking Sir2A or Sir2B high var transcription levels correlate with enrichment of PfH2A.Z at the TSS. As Sir2A knock out parasites mature the var genes are

Microscopy analysis of soils at the Phoenix landing site, Mars : Classification of soil particles and description of their optical and magnetic properties

NARCIS (Netherlands)

Goetz, W.; Pike, W.T.; Hviid, S.F.; Madsen, M.B.; Morris, R.V.; Hecht, M.H.; Staufer, U.; Leer, K.; Sykulska, H.; Hemmig, E.; Marshall, J.; Morookian, J.M.; Parrat, D.; Vijendran, S.; Bos, B.J.; El Maarry, M.R.; Keller, H.U.; Kramm, R.; Markiewicz, W.J.; Drube, L.; Blaney, D.; Arvidson, R.E.; Bell, J.F.; Reynolds, R.; Smith, P.H.; Woida, P.; Woida, R.; Tanner, R.

2010-01-01

The optical microscope onboard the Phoenix spacecraft has returned color images (4 ?m pixel?1) of soils that were delivered to and held on various substrates. A preliminary taxonomy of Phoenix soil particles, based on color, size, and shape, identifies the following particle types [generic names in

Tuhast tõusnud Phoenix jõudis Marsile elu võimalikkust uurima / Liisi Poll

Index Scriptorium Estoniae

Poll, Liisi, 1980-

2008-01-01

Vt. ka Postimees : na russkom jazõke 27. mai, lk. 8. Marsile jõudnud NASA automaatjaam Phoenix maandus naaberplaneedi põhjapoolusele lähemale kui ükski inimese leiutatud masin kunagi varem. Lisa: Marsi uurimiste ajalugu

Recommendation Report: EJournals/EBooks A-Z Management System

KAUST Repository

Ramli, Rindra M.

2014-01-01

This is a recommendation report for KAUST Library on the Ejournals / EBooks AZ Management systems project. It briefly described the issues faced by the ERM Team, project plan overview and the project findings as well as the recommendation(s).

Arsenic Removal from Drinking Water by Adsorptive Media - U.S. EPA Demonstration Project at Covered Wells in Tohono O’odham Nation, AZ - Final Performance Evaluation Report

Science.gov (United States)

This report documents the activities performed and the results obtained from the arsenic removal treatment technology demonstration project at Covered Wells in Tohono O’odham Nation, AZ. The main objective of the project was to evaluate the effectiveness of AdEdge Technologies’ ...

Status of the PHOENIX electron cyclotron resonance charge breeder at ISOLDE, CERN.

Science.gov (United States)

Barton, Charles; Cederkall, Joakim; Delahaye, Pierre; Kester, Oliver; Lamy, Thierry; Marie-Jeanne, Mélanie

2008-02-01

We report here on the last progresses made with the PHOENIX electron cyclotron resonance charge breeder test bench at ISOLDE. Recently, an experiment was performed to test the trapping of (61)Fe daughter nuclides from the decay of (61)Mn nuclides. Preliminary results are given.

Status of the PHOENIX electron cyclotron resonance charge breeder at ISOLDE, CERN

International Nuclear Information System (INIS)

Barton, Charles; Cederkall, Joakim; Delahaye, Pierre; Kester, Oliver; Lamy, Thierry; Marie-Jeanne, Melanie

2008-01-01

We report here on the last progresses made with the PHOENIX electron cyclotron resonance charge breeder test bench at ISOLDE. Recently, an experiment was performed to test the trapping of 61 Fe daughter nuclides from the decay of 61 Mn nuclides. Preliminary results are given

Study with a steam tracer in a zone near well Az-64, in the Los Azufres geothermal field, Mich.; Estudio con un trazador de vapor en la zona aledana al pozo Az-64, en el campo geotermico de Los Azufres, Mich.

Energy Technology Data Exchange (ETDEWEB)

Iglesias, Eduardo R. [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)]. E-mail: iglesias@iie.org.mx; Flores Armenta, Magaly; Quijano Leon, Jose Luis; Torres Rodriguez, Marco A. [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico); Torres, Rodolfo J.; Reyes Picasso, Neftali [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Sandoval Medina, Fernando [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)

2009-01-15

A previous tracer study in the Maritaro-La Cumbre area of the Los Azufres, Mich., geothermal field concluded that injection in well Az-15 recharges a group of producing wells located east of the injector to a maximum distance of about 2000 m. The study also indicated injection in Az-15 either does not recharge wells farther east in the neighborhood of the Laguna Verde fault, or does so at very low rates over a long period. Because it is important to recharge this zone, it was decided to explore the possibility of doing it by injecting in well Az-64, located in the area. Thus the present study was designed. Six producing wells were chosen to monitor tracer arrivals. Because all the chosen wells produce steam (several also produce water) and for economic reasons, it was decided to use a steam-phase tracer. We chose sulfur hexafluoride (SF6), a tracer successfully used before in the field. On October 24, 2006, we injected 96.4 kg of SF6 into well Az-64. All six chosen wells were sampled for 156 days, starting the day of injection. The tracer was detected in all six wells and for every well the shape of the residence curve clearly depicted the fractured nature of the corresponding permeability. Again in every case, the recovery curves indicated recovery was completed within the 156-day sampling period. The largest recoveries were in wells Az-05 (48.5%) and Az-43 (1.27%), those closest to the injection well and on the same side of the Maritaro fault as Az-64. Well Az-51, lying at 848 m from the injector and farthest away, registered the third-highest recovery percentage (1.01 x 10-5%), significantly higher than well Az-19 (6.95 x 10-6%), located 490 m from the injector; the two wells are on the same side of the Maritaro fault as Az-64. Well Az-32, located 423 m from the injector, but on the other side of the Maritaro fault, recovered 5.6 x 10-7% of the injected tracer, comparable to 8.67 x 10-7%, the amount recovered in well Az-13 on the same side of the Maritaro fault

The study of a Mg-rich epoxy primer for protection of AZ91D magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Lu Xiangyu [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Zuo Yu, E-mail: zuoy@mail.buct.edu.c [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Zhao Xuhui; Tang Yuming; Feng Xingguo [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China)

2011-01-15

Research highlights: {yields} A Mg-rich epoxy primer was prepared by adding pure magnesium particles in epoxy coating. Cross scratch testing results showed that in 3% NaCl solution the Mg-rich primer showed better protection for AZ91D magnesium alloy than the same epoxy primer without Mg addition. {yields} The open circuit potential of AZ91D alloy in NaCl solution decreased after coated with Mg-rich coating, suggesting that cathodic protection effect of the Mg-rich coating on AZ91D alloy was present. {yields} EIS studies showed that during the immersion tests of AZ91D alloy with Mg-rich coating the magnesium particles in coating dissolved with the charge-transfer resistance R{sub ct} at the magnesium particle/coating interface decreased and the double-layer capacitance Q{sub dl} increased. While the coating resistance remained stable for a long time and corrosion of the AZ91D alloy substrate was obviously delayed. - Abstract: A Mg-rich epoxy primer was prepared by adding pure magnesium particles to an epoxy coating. The coating properties were studied with electrochemical impedance spectroscopy (EIS), scanning electronic microscopy (SEM) and X-ray diffraction (XRD). The Mg-rich primer showed better protection for AZ91D magnesium alloy than the same epoxy primer without Mg addition. The open circuit potential measurements showed cathodic protection effect of the Mg-rich primer on AZ91D alloy. Cross scratch testing showed that the Mg-rich primer provided better protection for the substrate than original epoxy coating. The precipitation of Mg(OH){sub 2} in the coating also provided some degree of barrier protection.

The study of a Mg-rich epoxy primer for protection of AZ91D magnesium alloy

International Nuclear Information System (INIS)

Lu Xiangyu; Zuo Yu; Zhao Xuhui; Tang Yuming; Feng Xingguo

2011-01-01

Research highlights: → A Mg-rich epoxy primer was prepared by adding pure magnesium particles in epoxy coating. Cross scratch testing results showed that in 3% NaCl solution the Mg-rich primer showed better protection for AZ91D magnesium alloy than the same epoxy primer without Mg addition. → The open circuit potential of AZ91D alloy in NaCl solution decreased after coated with Mg-rich coating, suggesting that cathodic protection effect of the Mg-rich coating on AZ91D alloy was present. → EIS studies showed that during the immersion tests of AZ91D alloy with Mg-rich coating the magnesium particles in coating dissolved with the charge-transfer resistance R ct at the magnesium particle/coating interface decreased and the double-layer capacitance Q dl increased. While the coating resistance remained stable for a long time and corrosion of the AZ91D alloy substrate was obviously delayed. - Abstract: A Mg-rich epoxy primer was prepared by adding pure magnesium particles to an epoxy coating. The coating properties were studied with electrochemical impedance spectroscopy (EIS), scanning electronic microscopy (SEM) and X-ray diffraction (XRD). The Mg-rich primer showed better protection for AZ91D magnesium alloy than the same epoxy primer without Mg addition. The open circuit potential measurements showed cathodic protection effect of the Mg-rich primer on AZ91D alloy. Cross scratch testing showed that the Mg-rich primer provided better protection for the substrate than original epoxy coating. The precipitation of Mg(OH) 2 in the coating also provided some degree of barrier protection.

Results of the Phoenix Relative Humidity Sensor Recalibration

Science.gov (United States)

Martinez, G.; Fischer, E.; Renno, N. O.

2017-12-01

We show results of the recalibration of the Thermal and Electrical Conductivity Probe (TECP) relative humidity (RH) sensor of the Phoenix Mars lander [Zent et al., 2009]. Due to uncertainties in its pre-flight calibration, which partially overlapped the environmental conditions found at the Phoenix landing site [Tamppari et al., 2010], only the raw, unprocessed output of the TECP RH sensor is available in NASA's Planetary Data System (PDS). The sensor's calibration was revised in 2016 to correct for inaccuracies at the lowest temperatures [Zent et al., 2016], but the new processed RH values were not posted in the PDS. We have been using a spare engineering unit of the TECP to recalibrate the sensor in the full range of Phoenix landing site conditions in the Michigan Mars Environmental Chamber (MMEC) [Fischer et al., 2016]. We compare raw output data of the engineering unit in the MMEC with that of the flight unit from the preflight calibration. We observed that the engineering unit's RH sensor output was shifted to higher values compared to the flight unit's output at the same conditions of temperature and humidity. Based on this shift, we use a translation function that fits the in-situ measurements of the flight unit into the engineering unit output space. To improve the accuracy of this function, we use additional observations corresponding to saturated conditions when near-surface fog was observed [Whiteway et al., 2009], as well as observations around noon when the RH is expected to be below 5%. The entire range of conditions observed on the Martian surface is covered in our recalibration. The raw output of the sensor is used to obtain a new calibration function. This allows us to obtain high-level RH data at Martian polar conditions. The recalibrated data will be posted in the PDS. REFERENCES: Fischer, E., et al. (2016), Astrobiology, 16, 12, doi: 10.1089/ast.2016.1525. Tamppari, L. K., et al. (2010), J. Geophys. Res., 115, E00E17, doi:10.1029/2009JE003415

Framing the Tenth Anniversary of 9/11:  A Comparison of CNN and Phoenix TV commemorative websites

OpenAIRE

Zhuang, Yuxi

2013-01-01

It has been more than ten years since the 9/11 attacks in 2001, but the events related to the attacks are still a focus for the whole world. This study examined the news coverage of the 9/11 tenth anniversary from Phoenix TV and CNN, which are among the most influential news media in China and the U.S., respectively. A systematic content analysis was performed using latest news, opinion articles, photographs, and videos as classified by CNN and Phoenix TV on their commemorative 9/11 tenth ann...

Acceptance Test Report for the 241-AZ-101 Ultrasonic Interface Level Analyzer

International Nuclear Information System (INIS)

ANDREWS, J.E.

2000-01-01

This document comprises the Acceptance Test Report for the 241-AZ-101 Ultrasonic Interface Level Analyzer. This document presents the results of Acceptance Testing of the 241-AZ-101 Ultrasonic Interface Level Analyzers (URSILLAs). Testing of the URSILLAs was performed in accordance with ATP-260-001, ''URSILLA Pre-installation Acceptance Test Procedure''. The objective of the testing was to verify that all equipment and components function in accordance with design specifications and original equipment manufacturer's specifications

Project W-211 Initial Tank Retrieval Systems (ITRS) Description of Operations for 241-AZ-102

Energy Technology Data Exchange (ETDEWEB)

BRIGGS, S.R.

2000-02-25

The primary purpose of the Initial Tank Retrieval Systems (ITRS) is to provide systems for retrieval of radioactive wastes stored in underground double-shell tanks (DSTs) for transfer to alternate storage, evaporation, pretreatment or treatment, while concurrently reducing risks associated with safety watch list and other DSTs. This Description of Operation (DOO) defines the control philosophy for the waste retrieval system for Tank 241-AZ-102 (AZ-102). This DOO provides a basis for the detailed design of the Project W-211 Retrieval Control System (RCS) for AZ-102 and also establishes test criteria for the RCS.

Project W-211 Initial Tank Retrieval Systems (ITRS) Description of Operations for 241-AZ-102

International Nuclear Information System (INIS)

BRIGGS, S.R.

2000-01-01

The primary purpose of the Initial Tank Retrieval Systems (ITRS) is to provide systems for retrieval of radioactive wastes stored in underground double-shell tanks (DSTs) for transfer to alternate storage, evaporation, pretreatment or treatment, while concurrently reducing risks associated with safety watch list and other DSTs. This Description of Operation (DOO) defines the control philosophy for the waste retrieval system for Tank 241-AZ-102 (AZ-102). This DOO provides a basis for the detailed design of the Project W-211 Retrieval Control System (RCS) for AZ-102 and also establishes test criteria for the RCS

75 FR 81190 - Television Broadcasting Services; Yuma, AZ

Science.gov (United States)

2010-12-27

... FEDERAL COMMUNICATIONS COMMISSION 47 CFR Part 73 [DA 10-2365; MB Docket No. 02-151; RM-10453] Television Broadcasting Services; Yuma, AZ AGENCY: Federal Communications Commission. ACTION: Dismissal. SUMMARY: The Commission dismisses the petition for rulemaking filed by Arizona Western College, requesting...

Cesium Removal From Tanks 241-AN-103 and 241-SX-105 and 241-AZ-101 and 241-AZ-102 Composite For Testing In Bench Scale Steam Reformer

International Nuclear Information System (INIS)

Duncan, J.B.; Huber, H.J.

2011-01-01

This report documents the preparation of three actual Hanford tank waste samples for shipment to the Savannah River National Laboratory (SRNL). Two of the samples were dissolved saltcakes from tank 241-AN-103 (hereafter AN-103) and tank 241-SX-105 (hereafter SX-105); one sample was a supernate composite from tanks 241-AZ-101 and 241-AZ-102 (hereafter AZ-101/102). The preparation of the samples was executed following the test plans LAB-PLAN-10-00006, Test Plan for the Preparation of Samples from Hanford Tanks 241-SX-105, 241-AN-103, 241-AN-107, and LAB-PLN-l0-00014, Test Plan for the Preparation of a Composite Sample from Hanford Tanks 241-AZ-101 and 241-AZ-102 for Steam Reformer Testing at the Savannah River National Laboratory. All procedural steps were recorded in laboratory notebook HNF-N-274 3. Sample breakdown diagrams for AN-103 and SX-105 are presented in Appendix A. The tank samples were prepared in support of a series of treatability studies of the Fluidized Bed Steam Reforming (FBSR) process using a Bench-Scale Reformer (BSR) at SRNL. Tests with simulants have shown that the FBSR mineralized waste form is comparable to low-activity waste glass with respect to environmental durability (WSRC-STI-2008-00268, Mineralization of Radioactive Wastes by Fluidized Bed Steam Reforming (FBSR): Comparisons to Vitreous Waste Forms and Pertinent Durability Testing). However, a rigorous assessment requires long-term performance data from FBSR product formed from actual Hanford tank waste. Washington River Protection Solutions, LLC (WRPS) has initiated a Waste Form Qualification Program (WP-5.2.1-2010-001, Fluidized Bed Steam Reformer Low-level Waste Form Qualification) to gather the data required to demonstrate that an adequate FBSR mineralized waste form can be produced. The documentation of the selection process of the three tank samples has been separately reported in RPP-48824, Sample Selection Process for Bench-Scale Steam Reforming Treatability Studies Using

Environmental friendly anodizing of AZ91D magnesium alloy in alkaline borate-benzoate electrolyte

Energy Technology Data Exchange (ETDEWEB)

Liu Yan [Department of Chemistry, Zhejiang University, Hangzhou 310027 (China); Department of Chemistry, Tianshui Normal University, Tianshui 741000 (China); Wei Zhongling [Magnesium Technology Co., Ltd., Chinese Academy of Sciences, Jiaxing 314051 (China); Yang Fuwei [Department of Chemistry, Tianshui Normal University, Tianshui 741000 (China); Zhang Zhao, E-mail: eaglezzy@zjuem.zju.edu.cn [Department of Chemistry, Zhejiang University, Hangzhou 310027 (China); Key Laboratory for Light Alloy Materials Technology, Jiaxing 314051 (China)

2011-06-02

Highlights: > Environmental friendly PEO technology for AZ91 magnesium alloy is developed. > NaBz is used as new additive and it is low-cost and environmental friendly. > The effect of NaBz additive on the properties of the anodized film was studied. > Anodized film with excellent corrosion resistance is obtained. > The forming mechanism of anodized film in the presence of NaBz is approached. - Abstract: A kind of environmental friendly anodizing routine for AZ91D magnesium alloy, based on an alkaline borate-sodium benzoate electrolyte (NaBz) was studied. The effect of NaBz on the properties of the anodized film was investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectrometry (EDS), potentiodynamic polarization and electrochemical impedance spectroscopy (EIS), respectively. The results showed that the anodizing process, surface morphology, thickness, phase structure and corrosion resistance of the anodized film were strongly dependent on the concentration of NaBz. In the presence of adequate NaBz, a thick, compact and smoothing anodized film with excellent corrosion resistance was produced. Moreover, the forming mechanism of the anodized film in the presence of NaBz additive was also approached, which was a suppression of arc discharge process by the adsorption of Bz{sup -} on the surface of magnesium alloy substrate.

Pierce - University of Georgia | Division of Cancer Prevention

Science.gov (United States)

Principal Investigator: J. Michael Pierce, PhDInstitution: University of Georgia, Athens, GA Our project, Discovery and Development of Cancer Glycomarkers, is a joint collaboration between our laboratories at the CCRC, which include Karen Abbott, Lance Wells, Kevin Dobbin, and Mike Tiemeyer, those at TGen, in Phoenix, AZ, Daniel Von Hoff, Haiyong Han, and Mike Demeure, and

Acceptance Test Report for the 241-AZ-101 Ultrasonic Interface Level Analyzer

Energy Technology Data Exchange (ETDEWEB)

ANDREWS, J.E.

2000-01-27

This document comprises the Acceptance Test Report for the 241-AZ-101 Ultrasonic Interface Level Analyzer. This document presents the results of Acceptance Testing of the 241-AZ-101 Ultrasonic Interface Level Analyzers (URSILLAs). Testing of the URSILLAs was performed in accordance with ATP-260-001, ''URSILLA Pre-installation Acceptance Test Procedure''. The objective of the testing was to verify that all equipment and components function in accordance with design specifications and original equipment manufacturer's specifications.

Debris flows from small catchments of the Ma Ha Tuak Range, metropolitan Phoenix, Arizona

Science.gov (United States)

Dorn, Ronald I.

2010-08-01

Debris flows debauch from tiny but steep mountain catchments throughout metropolitan Phoenix, Arizona, USA. Urban growth in the past half-decade has led to home construction directly underneath hundreds of debris-flow channels, but debris flows are not recognized as a potential hazard at present. One of the first steps in a hazard assessment is to determine occurrence rates. The north flank of the Ma Ha Tuak Range, just 10 km from downtown Phoenix, was selected to determine the feasibility of using the varnish microlaminations (VML) method to date every debris-flow levee from 127 catchment areas. Only 152 of the 780 debris-flow levees yielded VML ages in a first round of sampling; this high failure rate is due to erosion of VML by microcolonial fungi. The temporal pattern of preserved debris-flow levees indicates anomalously high production of debris flows at about 8.1 ka and about 2.8 ka, corresponding to Northern Hemisphere climatic anomalies. Because many prior debris flows are obliterated by newer events, the minimum overall occurrence rates of 1.3 debris flows per century for the last 60 ka, 2.2 flows/century for the latest Pleistocene, and 5 flows/century for the last 8.1 ka has little meaning in assessment of a contemporary hazard. This is because newer debris flows have obliterated an unknown number of past deposits. More meaningful to a hazards analysis is the estimate that 56 flows have occurred in the last 100 years on the north side of the range, an estimate that is consistent with direct observations of three small debris flows resulting events from a January 18-22, 2010 storm producing 70 mm of precipitation in the Ma Ha Tuak Range, and a 500 m long debris flow in a northern metropolitan Phoenix location that received over 150 mm of precipitation in this same storm. These findings support the need for a more extensive hazard assessment of debris flows in metropolitan Phoenix.

Development of mechanical properties in a CaO added AZ31 magnesium alloy processed by equal-channel angular pressing

Energy Technology Data Exchange (ETDEWEB)

Bae, Seong-Hwan [Division of Materials Science and Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Metal Forming Technology R& D Group, Korea Institute of Industrial Technology, Incheon 406-840 (Korea, Republic of); Jung, Ki Ho; Shin, Young-Chul; Yoon, Duk Jae [Metal Forming Technology R& D Group, Korea Institute of Industrial Technology, Incheon 406-840 (Korea, Republic of); Kawasaki, Megumi, E-mail: megumi@hanyang.ac.kr [Division of Materials Science and Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Departments of Aerospace & Mechanical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089-1453 (United States)

2016-02-15

Processing through the application of equal-channel angular pressing (ECAP) is recognized as one of the attractive severe plastic deformation techniques where the processed bulk metals generally achieve ultrafine-grained microstructure leading to improved physical characteristics and mechanical properties. Magnesium has received much attention to date for its lightweight, high strength and excellent elasticity. Mg alloys with addition of CaO is reported to provide the successful casting procedure without usage of greenhouse gas, SF{sub 6}, whereas it is generally used for preventing the oxidation of Mg during casting. In the present investigation, a CaO added AZ31 (AZ31-CaO) magnesium alloy was processed by ECAP at elevated temepratures with a few steps of reduction which result in significant grain refinement to ~ 1.5 μm after 6 passes. Compression testing at room temperature demonstrated the AZ31-CaO alloy after ECAP showed enhanced yield strength more than the as-processed commercial AZ31 alloy while both alloys maintained ductility in spite of significant reduction in grain size. The improved strength in the AZ31-CaO alloy was attributed to the formation of fine Al{sub 2}Ca precipitates which experience breaking-up through ECAP and accelerate the microstructural refinement. Moreover, the preservation of ductility was attributed to the enhancement of strain hardening capability in the AZ31 alloy at room temperature. This study discusses the feasibility of using ECAP to improve both strength and ductility on magnesium alloys by applying the diagram describing the paradox of strength and ductility. - Highlights: • AZ31 and AZ31-CaO magnesium alloys were processed by ECAP up to 6 passes. • AZ31-CaO alloy after ECAP showed improved yield strength without losing ductility. • CaO in AZ31 forms fine Al{sub 2}Ca accelerating microstructural refinement during ECAP. • Feasibility of using ECAP was shown to improve both strength and ductility in Mg.

Development of mechanical properties in a CaO added AZ31 magnesium alloy processed by equal-channel angular pressing

International Nuclear Information System (INIS)

Bae, Seong-Hwan; Jung, Ki Ho; Shin, Young-Chul; Yoon, Duk Jae; Kawasaki, Megumi

2016-01-01

Processing through the application of equal-channel angular pressing (ECAP) is recognized as one of the attractive severe plastic deformation techniques where the processed bulk metals generally achieve ultrafine-grained microstructure leading to improved physical characteristics and mechanical properties. Magnesium has received much attention to date for its lightweight, high strength and excellent elasticity. Mg alloys with addition of CaO is reported to provide the successful casting procedure without usage of greenhouse gas, SF 6 , whereas it is generally used for preventing the oxidation of Mg during casting. In the present investigation, a CaO added AZ31 (AZ31-CaO) magnesium alloy was processed by ECAP at elevated temepratures with a few steps of reduction which result in significant grain refinement to ~ 1.5 μm after 6 passes. Compression testing at room temperature demonstrated the AZ31-CaO alloy after ECAP showed enhanced yield strength more than the as-processed commercial AZ31 alloy while both alloys maintained ductility in spite of significant reduction in grain size. The improved strength in the AZ31-CaO alloy was attributed to the formation of fine Al 2 Ca precipitates which experience breaking-up through ECAP and accelerate the microstructural refinement. Moreover, the preservation of ductility was attributed to the enhancement of strain hardening capability in the AZ31 alloy at room temperature. This study discusses the feasibility of using ECAP to improve both strength and ductility on magnesium alloys by applying the diagram describing the paradox of strength and ductility. - Highlights: • AZ31 and AZ31-CaO magnesium alloys were processed by ECAP up to 6 passes. • AZ31-CaO alloy after ECAP showed improved yield strength without losing ductility. • CaO in AZ31 forms fine Al 2 Ca accelerating microstructural refinement during ECAP. • Feasibility of using ECAP was shown to improve both strength and ductility in Mg.

Field observations of regional and urban impacts on NO2, ozone, UVB, and nitrate radical production rates in the Phoenix air basin

International Nuclear Information System (INIS)

Gaffney, J.S.; Marley, N.A.; Drayton, P.J.; Doskey, P.V.; Kotamarthi, V.R.; Cunningham, M.M.; Baird, J.C.; Dintaman, J.; Hart, H.L.

2002-01-01

In the May and June of 1998, field measurements were taken at a site near the Usery Pass Recreation Area, ∼27 miles from the downtown Phoenix area, overlooking Phoenix and Mesa, Arizona. This site was selected to examine the impacts of the Phoenix urban plume on the Usery Pass Recreation Area and surrounding regions. Data were obtained for ultraviolet-B (UVB) radiation, nitrogen dioxide (NO 2 ), peroxyacetyl nitrate (PAN), ozone (O 3 ), and carbon monoxide (CO). Nocturnal plumes of NO 2 (in tens of ppb), observed near midnight, were correlated with CO and anti-correlated with O 3 . This behavior was consistent with the titration of locally generated NO by boundary layer O 3 to form the nighttime NO 2 plumes that were subsequently transported into the Usery Pass Recreation area. Nitrate radical (NO 3 ) production rates were calculated to be very high on the edges of these nocturnal plumes. Examination of O 3 and PAN data also indicates that Phoenix is being affected by long-range transport of pollutants from the Los Angeles to San Diego areas. A regional smoke episode was observed in May, accompanied by a decrease in UVB of factor of two and a decrease in O 3 and an increase in methyl chloride. Low level back trajectories and chemical evidence confirm that the smoke event originated in northern Mexico and that the reduced O 3 levels observed at Usery Pass could be partially due to reduced photolysis rates caused by carbonaceous soot aerosols transported in the smoke plume. The results are discussed with regard to potential effects of local pollution transport from the Phoenix air basin as well as an assessment of the contributions from long-range transport of pollutants to the background levels in the Phoenix-Usery Pass area. (author)

An exponential material model for prediction of the flow curves of several AZ series magnesium alloys in tension and compression

International Nuclear Information System (INIS)

Fereshteh-Saniee, F.; Barati, F.; Badnava, H.; Fallah Nejad, Kh.

2012-01-01

Highlights: ► The exponential model can represent flow behaviors of AZ series Mg alloys very well. ► Strain rate sensitivities of AZ series Mg alloys in compression are nearly the same. ► Effect of zinc element on tensile activation energy is higher than on compressive one. ► Activation energies of AZ80 and AZ81 in tension were greater than in compression. ► Tensile and compressive rate sensitivities of AZ80 are not close to each other. -- Abstract: This paper is concerned with flow behaviors of several magnesium alloys, such as AZ31, AZ80 and AZ81, in tension and compression. The experiments were performed at elevated temperatures and for various strain rates. In order to eliminate the effect of inhomogeneous deformation in tensile and compression tests, the Bridgeman’s and numerical correction factors were respectively employed. A two-section exponential mathematical model was also utilized for prediction of flow stresses of different magnesium alloys in tension and compression. Moreover, based on the compressive flow model proposed, the peak stress and the relevant true strain could be estimated. The true stress and strain of the necking point can also be predicted using the corresponding relations. It was found that the flow behaviors estimated by the exponential flow model were encouragingly in very good agreement with experimental findings.

Patrón de consumo e ingestas recomendadas de azúcar

OpenAIRE

Joan Quiles i Izquierdo

2013-01-01

Los azúcares son hidratos de carbono con sabor dulce que proveen energía al organismo. El cerebro adulto utiliza aproximadamente 140 g de glucosa al día, cantidad que puede representar hasta el 50% del total de hidratos de carbono que se consumen. En nuestro país el patrón de consumo de azúcar en alimentos permanece constante, mientras que el consumo de bebidas refrescantes presenta un aumento en los últimos cuatro años. La Encuesta Nacional de Ingesta Dietética de España (ENIDE, 2010-11) est...

Diffusion Bonding and Post-Weld Heat Treatment of Extruded AZ91 Magnesium Alloys

Directory of Open Access Journals (Sweden)

Fei LIN

2015-11-01

Full Text Available The grain size of as-extruded AZ91 magnesium alloys was refined to 12.31 μm from 21.41 μm by recrystallization annealing. The vacuum diffusion welding of as-annealed AZ91 magnesium alloys was researched. The results showed that the maximum shear strength of joints reached 64.70 MPa in the situation of 10 MPa bonding pressure, 18 Pa vacuum degree, 470 °C bonding temperature and 90 min bonding time; both bonding temperature and time are the main influence factors on as-extruded AZ91 magnesium alloys diffusion welding. Then the diffusion welded specimens were annealed, and the shear strength of joints was further improved to 76.93 MPa.DOI: http://dx.doi.org/10.5755/j01.ms.21.4.9699

EnviroAtlas - Phoenix, AZ - Land Cover by Block Group

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset describes the percentage of each block group that is classified as impervious, forest, agriculture, and green space. Forest is combination...

EnviroAtlas - Phoenix, AZ - Near Road Block Group Summary

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset addresses the tree buffer along heavily traveled roads. The roads are interstates, arterials, and collectors within the EnviroAtlas...

The effects of alloying elements on microstructures and mechanical properties of tungsten inert gas welded AZ80 magnesium alloys joint

Science.gov (United States)

Li, Hui; Zhang, Jiansheng; Ding, Rongrong

2017-11-01

The effects of alloying elements on the macrostructures, microstructures and tensile strength of AZ80 Mg alloy weldments were studied in the present study. The results indicate that with the decrease of Al element content of filler wire, the welding defects of seam are gradually eliminated and the β-Mg17Al12 phases at α-Mg boundaries are refined and become discontinuous, which are beneficial to the improvement of tensile strength. With AZ31 Mg alloy filler wire, the maximum tensile strength of AZ80 weldment is 220 MPa and fracture occurs at the welding seam of joint. It is experimentally proved that robust AZ80 Mg alloy joints can be obtained by tungsten inert gas (TIG) welding process with AZ31 Mg alloy filler wire. However, further study is required to improve the microstructures and reduce welding defects of joint in order to further improve the joining strength of AZ80 Mg alloy joint.

Destruction of the Phoenix/Hibiscus and Barringtonia racemosa Communities at Richards Bay, Natal, South Africa

Directory of Open Access Journals (Sweden)

P. J. Weisser

1982-10-01

Full Text Available The destruction of the Phoenix!Hibiscus and Barringtonia racemosa Communities described by Venter in 1972 on the southern shores of Richards Bay is reported. The cause was the artificial openingof a new mouth about 5,5 km south of the original mouth, which increased tidal range and salinity. These swamp communities occupied a narrow band about 6 ha in area behind the Bruguiera gymnorrhiza Community. An estimated 95 % of the communities was affected and only on the landward border were some isolated remnants of species such as Acrostichum aureum, Hibiscus tiliaceus and Phoenix reclinata detected .Young stands of  Phragmites australis, seedlings of  Bruguiera gymnorrhiza and Avicennia marina and epipelic algae are recoIonizing the affected area.

Effect of Pr addition on microstructure and mechanical properties of AZ61 magnesium alloy

Directory of Open Access Journals (Sweden)

You Zhiyong

2014-03-01

Full Text Available To improve the strength, hardness and heat resistance of Mg-6Al-1Zn (AZ61 alloy, the effects of Pr addition on the as-cast microstructure and mechanical properties of AZ61 alloy were investigated at room and elevated temperatures by means of Brinell hardness measurement, optical microscope (OM, scanning electron microscope (SEM, energy dispersive spectroscopy (EDS, X-ray diffractometer (XRD and DNS100 electronic universal testing machine. The results show that the microstructures of Pr-containing AZ61 alloys were refined, with primary β-Mg17Al12 phase distributed homogeneously. When the addition of Pr is up to 1.2wt.%, the β phase becomes finer, and new needle-like or short-rod shaped Al11Pr3 phase and blocky AlPr phase appear. As a result, optimal tensile properties are obtained. However, greater than 1.2wt.% Pr addition leads to poorer mechanical properties due to the aggregation of the needle-like phase and large size of grains. The present research findings provide a new way for strengthening of magnesium alloys at room and elevated temperatures, and a method of producing thermally-stable AZ61 magnesium alloy.

Study on fused/cast AZS refractories for deployment in vitrification of radioactive waste effluents

Science.gov (United States)

Sengupta, Pranesh; Mishra, R. K.; Soudamini, N.; Sen, D.; Mazumder, S.; Kaushik, C. P.; Ajithkumar, T. G.; Banerjee, K.

2015-12-01

'Fused/cast Al2O3-ZrO2-SiO2 (FC-AZS)' is being considered as 'glass contact refractory' within ceramic melters, to be used for nuclear waste immobilization. Microstructural analyses reveal random distributions of baddeleyite (ZrO2) within aluminosilicate (Al2SiO5) matrix. 27Al and 29Si NMR data suggest that within aluminosilicate matrix Al occurs in both 4- and 6-fold co-ordinations whereas Si prefers a 4-fold environment. Polydispersity of pores has been studied with small-angle neutron scattering (SANS) technique. Corrosion rates of FC-AZS within 6 M HNO3, simulated wastes (500 h exposure), and borosilicate melt (975 °C, 800 h exposure) are found to be 0.38 × 103 μmy-1, 0.13 × 103 μmy-1 and 4.75 × 103 μmy-1 respectively. A comparison of chemical interaction data clearly suggests that FC-AZS exhibits better chemical durability than AZC refractory (Al2O3-ZrO2-Cr2O3, also used for similar purpose). Thermal cycling studies indicate that FC-AZS retains structural integrity (including compressive strength and density) even up to 20 cycles.

Visual Analytics for the Food-Water-Energy Nexus in the Phoenix Active Management Area

Science.gov (United States)

Maciejewski, R.; Mascaro, G.; White, D. D.; Ruddell, B. L.; Aggarwal, R.; Sarjoughian, H.

2016-12-01

The Phoenix Active Management Area (AMA) is an administrative region of 14,500 km2 identified by the Arizona Department of Water Resources with the aim of reaching and maintaining the safe yield (i.e. balance between annual amount of groundwater withdrawn and recharged) by 2025. The AMA includes the Phoenix metropolitan area, which has experienced a dramatic population growth over the last decades with a progressive conversion of agricultural land into residential land. As a result of these changes, the water and energy demand as well as the food production in the region have significantly evolved over the last 30 years. Given the arid climate, a crucial role to support this growth has been the creation of a complex water supply system based on renewable and non-renewable resources, including the energy-intensive Central Arizona Project. In this talk, we present a preliminary characterization of the evolution in time of the feedbacks between food, water, and energy in the Phoenix AMA by analyzing secondary data (available from water and energy providers, irrigation districts, and municipalities), as well as satellite imagery and primary data collected by the authors. A preliminary visual analytics framework is also discussed describing current design practices and ideas for exploring networked components and cascading impacts within the FEW Nexus. This analysis and framework represent the first steps towards the development of an integrated modeling, visualization, and decision support infrastructure for comprehensive FEW systems decision making at decision-relevant temporal and spatial scales.

Blocking spinal CCR2 with AZ889 reversed hyperalgesia in a model of neuropathic pain

Directory of Open Access Journals (Sweden)

Vaillancourt François

2010-12-01

Full Text Available Abstract Background The CCR2/CCL2 system has been identified as a regulator in the pathogenesis of neuropathy-induced pain. However, CCR2 target validation in analgesia and the mechanism underlying antinociception produced by CCR2 antagonists remains poorly understood. In this study, in vitro and in vivo pharmacological approaches using a novel CCR2 antagonist, AZ889, strengthened the hypothesis of a CCR2 contribution to neuropathic pain and provided confidence over the possibilities to treat neuropathic pain with CCR2 antagonists. Results We provided evidence that dorsal root ganglia (DRG cells harvested from CCI animals responded to stimulation by CCL2 with a concentration-dependent calcium rise involving PLC-dependent internal stores. This response was associated with an increase in evoked neuronal action potentials suggesting these cells were sensitive to CCR2 signalling. Importantly, treatment with AZ889 abolished CCL2-evoked excitation confirming that this activity is CCR2-mediated. Neuronal and non-neuronal cells in the spinal cord were also excited by CCL2 applications indicating an important role of spinal CCR2 in neuropathic pain. We next showed that in vivo spinal intrathecal injection of AZ889 produced dose-dependent analgesia in CCI rats. Additionally, application of AZ889 to the exposed spinal cord inhibited evoked neuronal activity and confirmed that CCR2-mediated analgesia involved predominantly the spinal cord. Furthermore, AZ889 abolished NMDA-dependent wind-up of spinal withdrawal reflex pathway in neuropathic animals giving insight into the spinal mechanism underlying the analgesic properties of AZ889. Conclusions Overall, this study strengthens the important role of CCR2 in neuropathic pain and highlights feasibility that interfering on this mechanism at the spinal level with a selective antagonist can provide new analgesia opportunities.

Effect of Rare Earth on Corrosion Products and Impedance Behavior of AZ91 Magnesium Alloy Under Dry-wet Cycles

Directory of Open Access Journals (Sweden)

ZHAO Xi

2017-04-01

Full Text Available The effect of mischmetal of lanthanum and cerium on the composition and structure of the corrosion products on the surface of AZ91 Mg alloy in deicing salt solution under dry-wet cycles was investigated by scanning electron microscopy (SEM, X-ray diffraction (XRD and energy dispersive spectrometer (EDS. The results show that the corrosion products of AZ91 Mg alloy without mischmetal addition (La,Ce are mainly composed of Mg(OH2, MgO, CaCO3 and Mg6Al2CO3(OH16·4H2O; and (La,CeAlO3 can be found in the products of AZ91 with mischmetal addition, meanwhile dense layer occurs in the corrosion products. Electrochemical impedance spectroscopy (EIS measurements show that the charge transfer resistance of AZ91 alloy with mischmetal addition tested in the same dry-wet cycles is much higher than that of AZ91 alloy, the addition of mischmetal helps to reduce the dispersing effect of impedance spectroscopy, indicating that the corrosion resistance of AZ91 Mg alloy and the stability of corrosion product films can be improved by mischmetal of La and Ce.

Effectiveness of Ti-micro alloying in relation to cooling rate on corrosion of AZ91 Mg alloy

International Nuclear Information System (INIS)

Candan, S.; Celik, M.; Candan, E.

2016-01-01

In this study, micro Ti-alloyed AZ91 Mg alloys (AZ91 + 0.5wt.%Ti) have been investigated in order to clarify effectiveness of micro alloying and/or cooling rate on their corrosion properties. Molten alloys were solidified under various cooling rates by using four stage step mold. The microstructural investigations were carried out by using scanning electron microscopy (SEM). Corrosion behaviors of the alloys were evaluated by means of immersion and electrochemical polarization tests in 3.5% NaCl solution. Results showed that the Mg 17 Al 12 (β) intermetallic phase in the microstructure of AZ91 Mg alloy formed as a net-like structure. The Ti addition has reduced the distribution and continuity of β intermetallic phase and its morphology has emerged as fully divorced eutectic. Compared to AZ91 alloy, the effect of the cooling rate in Ti-added alloy on the grain size was less pronounced. When AZ91 and its Ti-added alloys were compared under the same cooling conditions, the Ti addition showed notably high corrosion resistance. Electrochemical test results showed that while I corr values of AZ91 decrease with the increase in the cooling rate, the effect of the cooling rate on I corr values was much lower in the Ti-added alloy. The corrosion resistance of AZ91 Mg alloy was sensitive towards the cooling rates while Ti-added alloy was not affected much from the cooling conditions. - Highlights: • Effect the cooling rate on grain size was less pronounced in the Ti-added alloy. • The morphology of the β phase transformed into fully divorced eutectics. • Ti addition exhibited significantly higher corrosion resistance. • Ti micro alloying is more effective than faster cooling of the alloy on corrosion.

TIP48/Reptin and H2A.Z requirement for initiating chromatin remodeling in estrogen-activated transcription.

Directory of Open Access Journals (Sweden)

Mathieu Dalvai

2013-04-01

Full Text Available Histone variants, including histone H2A.Z, are incorporated into specific genomic sites and participate in transcription regulation. The role of H2A.Z at these sites remains poorly characterized. Our study investigates changes in the chromatin environment at the Cyclin D1 gene (CCND1 during transcriptional initiation in response to estradiol in estrogen receptor positive mammary tumour cells. We show that H2A.Z is present at the transcription start-site and downstream enhancer sequences of CCND1 when the gene is poorly transcribed. Stimulation of CCND1 expression required release of H2A.Z concomitantly from both these DNA elements. The AAA+ family members TIP48/reptin and the histone variant H2A.Z are required to remodel the chromatin environment at CCND1 as a prerequisite for binding of the estrogen receptor (ERα in the presence of hormone. TIP48 promotes acetylation and exchange of H2A.Z, which triggers a dissociation of the CCND1 3' enhancer from the promoter, thereby releasing a repressive intragenic loop. This release then enables the estrogen receptor to bind to the CCND1 promoter. Our findings provide new insight into the priming of chromatin required for transcription factor access to their target sequence. Dynamic release of gene loops could be a rapid means to remodel chromatin and to stimulate transcription in response to hormones.

Photometric Properties of Soils at the Mars Phoenix Landing Site: Preliminary Analysis from CRISM EPF Data

Science.gov (United States)

Cull, S. C.; Arvidson, R. E.; Seelos, F.; Wolff, M. J.

2010-03-01

Using data from CRISM's Emission Phase Function observations, we attempt to constrain Phoenix soil scattering properties, including soil grain size, single-scattering albedo, and surface phase function.

A biodegradable AZ91 magnesium alloy coated with a thin nanostructured hydroxyapatite for improving the corrosion resistance

Energy Technology Data Exchange (ETDEWEB)

Mukhametkaliyev, T.M.; Surmeneva, M.A. [National Research Tomsk Polytechnic University, 634050, Lenin Avenue 43, Tomsk (Russian Federation); Vladescu, A. [National Research Tomsk Polytechnic University, 634050, Lenin Avenue 43, Tomsk (Russian Federation); National Institute for Optoelectronics, 409 Atomistilor St., RO77125 Magurele (Romania); Cotrut, C.M. [National Research Tomsk Polytechnic University, 634050, Lenin Avenue 43, Tomsk (Russian Federation); Politehnica University of Bucharest, 313 Spl. Independentei, Bucharest (Romania); Braic, M.; Dinu, M. [National Institute for Optoelectronics, 409 Atomistilor St., RO77125 Magurele (Romania); Vranceanu, M.D. [Politehnica University of Bucharest, 313 Spl. Independentei, Bucharest (Romania); Pana, I. [National Institute for Optoelectronics, 409 Atomistilor St., RO77125 Magurele (Romania); Faculty of Physics, Bucharest University, 405 Atomistilor St., RO77125 Magurele (Romania); Mueller, M. [Fraunhofer Institute for Interfacial Engineering and Biotechnology IGB, 70569 Stuttgart (Germany); Surmenev, R.A., E-mail: rsurmenev@gmail.com [National Research Tomsk Polytechnic University, 634050, Lenin Avenue 43, Tomsk (Russian Federation)

2017-06-01

The main aim of this study was to investigate the properties of an AZ91 alloy coated with nanostructured hydroxyapatite (HA) prepared by radio frequency (RF) magnetron sputtering. The bioactivity and biomineralization of the AZ91 magnesium alloy coated with HA were investigated in simulated body fluid (SBF) via an in vitro test. Scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and X-ray diffraction (XRD) analyses were performed. The samples were immersed in SBF to study the ability of the surface to promote the formation of an apatite layer as well as corrosion resistance and mass change of the HA-coated AZ91 alloy. Electrochemical tests were performed to estimate the corrosion behaviour of HA-coated and uncoated samples. The results revealed the capability of the HA coating to significantly improve the corrosion resistance of the uncoated AZ91 alloy. - Highlights: • The nanostructured HA layer allows to control the degradation rate of the AZ91 alloy. • The HA coating significantly reduces the corrosion current density. • The HA coating significantly improves the polarization resistance in vitro. • The RF magnetron deposited HA coating promotes calcium-phosphate precipitation in SBF.

A biodegradable AZ91 magnesium alloy coated with a thin nanostructured hydroxyapatite for improving the corrosion resistance

International Nuclear Information System (INIS)

Mukhametkaliyev, T.M.; Surmeneva, M.A.; Vladescu, A.; Cotrut, C.M.; Braic, M.; Dinu, M.; Vranceanu, M.D.; Pana, I.; Mueller, M.; Surmenev, R.A.

2017-01-01

The main aim of this study was to investigate the properties of an AZ91 alloy coated with nanostructured hydroxyapatite (HA) prepared by radio frequency (RF) magnetron sputtering. The bioactivity and biomineralization of the AZ91 magnesium alloy coated with HA were investigated in simulated body fluid (SBF) via an in vitro test. Scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and X-ray diffraction (XRD) analyses were performed. The samples were immersed in SBF to study the ability of the surface to promote the formation of an apatite layer as well as corrosion resistance and mass change of the HA-coated AZ91 alloy. Electrochemical tests were performed to estimate the corrosion behaviour of HA-coated and uncoated samples. The results revealed the capability of the HA coating to significantly improve the corrosion resistance of the uncoated AZ91 alloy. - Highlights: • The nanostructured HA layer allows to control the degradation rate of the AZ91 alloy. • The HA coating significantly reduces the corrosion current density. • The HA coating significantly improves the polarization resistance in vitro. • The RF magnetron deposited HA coating promotes calcium-phosphate precipitation in SBF.

Influencia de compuestos azúcares y no azúcares en la calidad industrial de caña de azúcar en Tucumán, R. Argentina: caña verde y quemada (Parte 2 Effect of sugar and non sugar compounds on sugar cane industrial quality in Tucumán (Argentina

Directory of Open Access Journals (Sweden)

B. Silvia Zossi

2011-06-01

Full Text Available A partir de 1997 en Tucumán, R. Argentina, entre el 65% y el 85% de la caña destinada a la producción de azúcar se cosecha en verde o quemada, mediante el sistema de cosecha integral. El resto del cultivo se cosecha en forma semimecánica, con un predominio del uso de la quema, del corte manual y carguío mecánico. La quema de caña, antes o después de ser cosechada, se realiza para remover las hojas adheridas a sus tallos, minimizando así el ingreso de no azúcares a la fábrica. Desde el año 2005, debido a disposiciones legislativas, la cosecha de caña en verde fue aumentando gradualmente, lo que incrementó considerablemente la concentración de compuestos no azúcares en el proceso de elaboración de azúcar. Por ello se decidió evaluar los principales componentes azúcares y no azúcares, especialmente los formadores de color, y su influencia en el proceso fabril de las cuatro variedades comerciales más difundidas en la provincia: TUCCP 77-42, LCP 85-384, CP 65-357 y RA 87-3, cosechadas de tres maneras diferentes: tallo molible limpio, despuntado y sin hojas; caña quemada para eliminar las hojas y despuntada y caña cosechada en verde, con un 15% de "trash" (hojas y despunte aproximadamente. En este trabajo se presentan los datos obtenidos con cosecha en verde y quemada. Los resultados mostraron que la variedad LCP 85-384 es la que presentó el mejor comportamiento para la producción de azúcar, por su mayor contenido de este sacárido y menores tenores de fibra y compuestos no azúcares, independientemente del tipo de cosecha. En las cuatro variedades estudiadas, disminuyeron la extracción de jugo y la cantidad de azúcar recuperable en fábrica y se incrementaron los contenidos de compuestos no azúcares, principalmente almidón y cenizas, cuando se trabajó con caña cosechada en verde.Since 1997 in Tucumán, Argentina, between 65% and 85% of cane for sugar production has been harvested mechanically, either green or burnt

Análisis del perfil de azúcares en la autentificación de zumos de frutas

OpenAIRE

Úbeda Gallego, Ana

2013-01-01

El objetivo general ha sido estudiar el perfil de azúcares por HPAEC-PAD para la autentificación de zumos de frutas de naranja, manzana y piña. Este objetivo general se ha dividido en los siguientes objetivos parciales: 1. Optimizar el método de análisis de azúcares por HPAEC-PAD. Para ello se han ensayado distintas concentraciones de NaOH en la fase móvil y distinta velocidad de flujo. Se han analizando muestras de azúcares, zumos concentrados y zumos comerciales. 2. Determinar el p...

Environmental friendly anodizing of AZ91D magnesium alloy in alkaline borate-benzoate electrolyte

International Nuclear Information System (INIS)

Liu Yan; Wei Zhongling; Yang Fuwei; Zhang Zhao

2011-01-01

Highlights: → Environmental friendly PEO technology for AZ91 magnesium alloy is developed. → NaBz is used as new additive and it is low-cost and environmental friendly. → The effect of NaBz additive on the properties of the anodized film was studied. → Anodized film with excellent corrosion resistance is obtained. → The forming mechanism of anodized film in the presence of NaBz is approached. - Abstract: A kind of environmental friendly anodizing routine for AZ91D magnesium alloy, based on an alkaline borate-sodium benzoate electrolyte (NaBz) was studied. The effect of NaBz on the properties of the anodized film was investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectrometry (EDS), potentiodynamic polarization and electrochemical impedance spectroscopy (EIS), respectively. The results showed that the anodizing process, surface morphology, thickness, phase structure and corrosion resistance of the anodized film were strongly dependent on the concentration of NaBz. In the presence of adequate NaBz, a thick, compact and smoothing anodized film with excellent corrosion resistance was produced. Moreover, the forming mechanism of the anodized film in the presence of NaBz additive was also approached, which was a suppression of arc discharge process by the adsorption of Bz - on the surface of magnesium alloy substrate.

CRED REA Coral Population Parameters at Howland, Phoenix Islands, Pacific Remote Island Areas in 2008

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Belt transects along 2 consecutively-placed, 25m transect lines were surveyed as part of Rapid Ecological Assessments conducted at 4 sites at Howland, Phoenix...

Salvage radiotherapy for patients with P.S.A. relapse after radical prostatectomy: comparisons among Astro and Phoenix biochemical failure definitions

International Nuclear Information System (INIS)

Quero, L.; Hennequin, V.; Maylin, C.; Hennequin, C.; Ravery, V.; Mongiat-Artus, P.; Desgrandchamps, F.

2009-01-01

Purpose Study about the efficacy of salvage radiotherapy (R.T.), in terms of biochemical disease free survival (b.D.F.S.), according to Astro and Phoenix (nadir + 2) definitions, for persistent or rising P.S.A. after radical prostatectomy. Patients and methods Retrospective analysis of 59 patients who underwent R.T. between 1990 and 2003 for P.S.A. recurrence after radical prostatectomy. Patients received a median of 66 Gy to the prostate bed with 3D or 2D R.T.. The main end point was b.D.F.S. according to Astro and Phoenix (nadir + 2) definitions. Different criterion sets were analysed to calculate b.D.F.S. and pretreatment factors that might predict biochemical relapse were sought for each. Results After a 38-month median follow-up, the 3-year b.D.F.S. rates were: 60 and 72% for Astro and Phoenix (nadir + 2 ng/ml) definitions respectively. According to univariate analysis, pre-R.T. P.S.A. = 1 ng/ml and seminal vesicle involvement were associated with biochemical relapse. Multivariate analysis retained only pre-R.T. P.S.A. = 1 ng/ml as an independent predictor of biochemical relapse for the two definitions. Conclusion Salvage R.T. is an effective treatment after radical prostatectomy according to Astro or Phoenix definitions. Only pre-R.T. P.S.A. = 1 ng/ml predicted relapse. (authors)

Tank 241-AZ-102 Privatization Push Mode Core Sampling and Analysis Plan; FINAL

International Nuclear Information System (INIS)

TEMPLETON, A.M.

1999-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AZ-102. The purpose of this sampling event is to obtain information about the characteristics of the contents of 241-AZ-102. Push mode core samples will be obtained from risers 15C and 24A to provide sufficient material for the chemical analyses and tests required to satisfy these data quality objectives. The 222-S Laboratory will extrude core samples, composite the liquids and solids, perform chemical analyses, and provide subsamples to the Process Chemistry Laboratory. The Process Chemistry Laboratory will prepare test plans and perform process tests to evaluate the behavior of the 241-AZ-102 waste undergoing the retrieval and treatment scenarios defined in the applicable DQOs. Requirements for analyses of samples originating in the process tests will be documented in the corresponding test plan

Influence of inorganic acid pickling on the corrosion resistance of magnesium alloy AZ31 sheet

DEFF Research Database (Denmark)

Nwaogu, Ugochukwu Chibuzoh; Blawert, C.; Scharnagl, N.

2009-01-01

Surface contaminants as a result of thermo-mechanical processing of magnesium alloys, e.g. sheet rolling, can have a negative effect on the corrosion resistance of magnesium alloys. Especially contaminants such as Fe, Ni and Cu, left on the surface of magnesium alloys result in the formation...... of micro-galvanic couples and can therefore increase corrosion attack on these alloys. Due to this influence they should be removed to obtain good corrosion resistance. In this study, the effect of inorganic acid pickling on the corrosion behaviour of a commercial AZ31 magnesium alloy sheet...... cleaning the AZ31 sheet. However, to obtain reasonable corrosion resistance at least 5 mu m of the surface of AZ31 magnesium alloy sheet have to be removed....

A biodegradable AZ91 magnesium alloy coated with a thin nanostructured hydroxyapatite for improving the corrosion resistance.

Science.gov (United States)

Mukhametkaliyev, T M; Surmeneva, M A; Vladescu, A; Cotrut, C M; Braic, M; Dinu, M; Vranceanu, M D; Pana, I; Mueller, M; Surmenev, R A

2017-06-01

The main aim of this study was to investigate the properties of an AZ91 alloy coated with nanostructured hydroxyapatite (HA) prepared by radio frequency (RF) magnetron sputtering. The bioactivity and biomineralization of the AZ91 magnesium alloy coated with HA were investigated in simulated body fluid (SBF) via an in vitro test. Scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and X-ray diffraction (XRD) analyses were performed. The samples were immersed in SBF to study the ability of the surface to promote the formation of an apatite layer as well as corrosion resistance and mass change of the HA-coated AZ91 alloy. Electrochemical tests were performed to estimate the corrosion behaviour of HA-coated and uncoated samples. The results revealed the capability of the HA coating to significantly improve the corrosion resistance of the uncoated AZ91 alloy. Copyright © 2017 Elsevier B.V. All rights reserved.

75 FR 883 - Environmental Impact Statement; Maricopa County, AZ

Science.gov (United States)

2010-01-06

...; Maricopa County, AZ AGENCY: Federal Highway Administration (FHWA), DOT. ACTION: Notice of Intent. SUMMARY...: (602) 382-8998, e-mail: [email protected] SUPPLEMENTARY INFORMATION: The FHWA, in cooperation with the... reasonable alternatives will be considered including: (1) Taking no action; (2) using alternate travel modes...

The ecological importance of mixed-severity fires: Nature's phoenix [Book Review

Science.gov (United States)

Carolyn H. Sieg

2016-01-01

The stated goal of a recent book, The Ecological Importance of Mixed-Severity Fires: Nature’s Phoenix, edited by Dominick A. DellaSala and Chad T. Hansen, is to provide a global reference on the benefits of mixed- and high-severity fires. Note that the goal is not to provide an objective reference on the ecological aspects of mixed- and high-severity fires. Rather, the...

Effects of sintering temperature on the corrosion behavior of AZ31 alloy with Ca–P sol–gel coating

Energy Technology Data Exchange (ETDEWEB)

Niu, Bo [School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou, Liaoning Province, 121001 (China); Shi, Ping, E-mail: p_shi@sohu.com [School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou, Liaoning Province, 121001 (China); Wei, Donghua [School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou, Liaoning Province, 121001 (China); E, Shanshan [School of Mathematics and Physics, Bohai University, Jinzhou, Liaoning Province, 121013 (China); Li, Qiang; Chen, Yang [School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou, Liaoning Province, 121001 (China)

2016-04-25

To slow down the initial biodegradation rate of magnesium alloy, calcium phosphate (Ca–P) coatings were prepared on AZ31 magnesium alloy by a sol–gel technique. To study the effects of sintering temperature on microstructure, bonding strength and corrosion behavior of the coatings, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and an adhesive strength test were used to characterize the coatings. The corrosion resistance of the coatings was investigated by immersion test and electrochemical corrosion techniques in simulated body fluid (SBF) solution. It shows that the sol–gel coatings consist of Ca{sub 2}P{sub 2}O{sub 7}, mixture of Ca{sub 2}P{sub 2}O{sub 7}, Ca{sub 3}(PO{sub 4}){sub 2} and hydroxyapatite, and hydroxyapatite, by sintering respectively at 300 °C, 400 °C and 500 °C. There are major cracks on the coatings. The crack area portion on the coating and the bonding strength at the interface between the calcium phosphate coating and the bare AZ31 increases, and the corrosion resistance of the coated AZ31 in SBF decreases with increasing sintering temperatures from 300 °C to 500 °C. Based on our investigations, the corrosion resistance of the coated AZ31 in SBF depends mainly on the crack area portion on the coatings, rather than on the coating phase stability. - Highlights: • Ca–P coating was prepared on AZ31 alloy by a sol–gel technique. • Crack area portion in the coating increases with temperatures. • Bonding strength between Ca–P coating and substrate increases with temperatures. • Corrosion resistance of the coated AZ31 in SBF decreases with temperatures. • Corrosion resistance of the coated AZ31 depends mainly on the crack area portion.

The Schizosaccharomyces pombe JmjC-protein, Msc1, prevents H2A.Z localization in centromeric and subtelomeric chromatin domains.

Directory of Open Access Journals (Sweden)

Luke Buchanan

2009-11-01

Full Text Available Eukaryotic genomes are repetitively packaged into chromatin by nucleosomes, however they are regulated by the differences between nucleosomes, which establish various chromatin states. Local chromatin cues direct the inheritance and propagation of chromatin status via self-reinforcing epigenetic mechanisms. Replication-independent histone exchange could potentially perturb chromatin status if histone exchange chaperones, such as Swr1C, loaded histone variants into wrong sites. Here we show that in Schizosaccharomyces pombe, like Saccharomyces cerevisiae, Swr1C is required for loading H2A.Z into specific sites, including the promoters of lowly expressed genes. However S. pombe Swr1C has an extra subunit, Msc1, which is a JumonjiC-domain protein of the Lid/Jarid1 family. Deletion of Msc1 did not disrupt the S. pombe Swr1C or its ability to bind and load H2A.Z into euchromatin, however H2A.Z was ectopically found in the inner centromere and in subtelomeric chromatin. Normally this subtelomeric region not only lacks H2A.Z but also shows uniformly lower levels of H3K4me2, H4K5, and K12 acetylation than euchromatin and disproportionately contains the most lowly expressed genes during vegetative growth, including many meiotic-specific genes. Genes within and adjacent to subtelomeric chromatin become overexpressed in the absence of either Msc1, Swr1, or paradoxically H2A.Z itself. We also show that H2A.Z is N-terminally acetylated before, and lysine acetylated after, loading into chromatin and that it physically associates with the Nap1 histone chaperone. However, we find a negative correlation between the genomic distributions of H2A.Z and Nap1/Hrp1/Hrp3, suggesting that the Nap1 chaperones remove H2A.Z from chromatin. These data describe H2A.Z action in S. pombe and identify a new mode of chromatin surveillance and maintenance based on negative regulation of histone variant misincorporation.

Influence of Sulfate-Reducing Bacteria on the Corrosion Residual Strength of an AZ91D Magnesium Alloy

Science.gov (United States)

Zhu, Xianyong; Liu, Yaohui; Wang, Qiang; Liu, Jiaan

2014-01-01

In this paper, the corrosion residual strength of the AZ91D magnesium alloy in the presence of sulfate-reducing bacteria is studied. In the experiments, the chemical composition of corrosion film was analyzed by a scanning electron microscope with energy dispersive X-ray spectroscopy. In addition, a series of instruments, such as scanning electronic microscope, pH-meter and an AG-10TA materials test machine, were applied to test and record the morphology of the corrosion product, fracture texture and mechanical properties of the AZ91D magnesium alloy. The experiments show that the sulfate-reducing bacteria (SRB) play an important role in the corrosion process of the AZ91D magnesium alloy. Pitting corrosion was enhanced by sulfate-reducing bacteria. Corrosion pits are important defects that could lead to a significant stress concentration in the tensile process. As a result, sulfate-reducing bacteria influence the corrosion residual strength of the AZ91D magnesium alloy by accelerating pitting corrosion. PMID:28788236

Tank 241-AZ-101 criticality assessment resulting from pump jet mixing: Sludge mixing simulation

Energy Technology Data Exchange (ETDEWEB)

Onishi, Y.; Recknagle, K.

1997-04-01

Tank 241-AZ-101 (AZ-101) is one of 28 double-shell tanks located in the AZ farm in the Hanford Site`s 200 East Area. The tank contains a significant quantity of fissile materials, including an estimated 9.782 kg of plutonium. Before beginning jet pump mixing for mitigative purposes, the operations must be evaluated to demonstrate that they will be subcritical under both normal and credible abnormal conditions. The main objective of this study was to address a concern about whether two 300-hp pumps with four rotating 18.3-m/s (60-ft/s) jets can concentrate plutonium in their pump housings during mixer pump operation and cause a criticality. The three-dimensional simulation was performed with the time-varying TEMPEST code to determine how much the pump jet mixing of Tank AZ-101 will concentrate plutonium in the pump housing. The AZ-101 model predicted that the total amount of plutonium within the pump housing peaks at 75 g at 10 simulation seconds and decreases to less than 10 g at four minutes. The plutonium concentration in the entire pump housing peaks at 0.60 g/L at 10 simulation seconds and is reduced to below 0.1 g/L after four minutes. Since the minimum critical concentration of plutonium is 2.6 g/L, and the minimum critical plutonium mass under idealized plutonium-water conditions is 520 g, these predicted maximums in the pump housing are much lower than the minimum plutonium conditions needed to reach a criticality level. The initial plutonium maximum of 1.88 g/L still results in safety factor of 4.3 in the pump housing during the pump jet mixing operation.

Tank 241-AZ-101 criticality assessment resulting from pump jet mixing: Sludge mixing simulation

International Nuclear Information System (INIS)

Onishi, Y.; Recknagle, K.

1997-04-01

Tank 241-AZ-101 (AZ-101) is one of 28 double-shell tanks located in the AZ farm in the Hanford Site's 200 East Area. The tank contains a significant quantity of fissile materials, including an estimated 9.782 kg of plutonium. Before beginning jet pump mixing for mitigative purposes, the operations must be evaluated to demonstrate that they will be subcritical under both normal and credible abnormal conditions. The main objective of this study was to address a concern about whether two 300-hp pumps with four rotating 18.3-m/s (60-ft/s) jets can concentrate plutonium in their pump housings during mixer pump operation and cause a criticality. The three-dimensional simulation was performed with the time-varying TEMPEST code to determine how much the pump jet mixing of Tank AZ-101 will concentrate plutonium in the pump housing. The AZ-101 model predicted that the total amount of plutonium within the pump housing peaks at 75 g at 10 simulation seconds and decreases to less than 10 g at four minutes. The plutonium concentration in the entire pump housing peaks at 0.60 g/L at 10 simulation seconds and is reduced to below 0.1 g/L after four minutes. Since the minimum critical concentration of plutonium is 2.6 g/L, and the minimum critical plutonium mass under idealized plutonium-water conditions is 520 g, these predicted maximums in the pump housing are much lower than the minimum plutonium conditions needed to reach a criticality level. The initial plutonium maximum of 1.88 g/L still results in safety factor of 4.3 in the pump housing during the pump jet mixing operation

Tank 241-AZ-102 Privatization Push Mode Core Sampling and Analysis Plan

International Nuclear Information System (INIS)

RASMUSSEN, J.H.

1999-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AZ-102. The purpose of this sampling event is to obtain information about the characteristics of the contents of 241-AZ-102 required to satisfy the Data Quality Objectives For TWRS Privatization Phase I : Confirm Tank TIS An Appropriate Feed Source For High-Level Waste Feed Batch X(HLW DQO) (Nguyen 1999a), Data Quality Objectives For TWRS Privatization Phase 1: Confirm Tank TIS An Appropriate Feed Source For Low-Activity Waste Feed Batch X (LAW DQO) (Nguyen 1999b), Low Activity Waste and High Level Waste Feed Data Quality Objectives (L and H DQO) (Patello et al. 1999) and Characterization Data Needs for Development, Design, and Operation of Retrieval Equipment Developed through the Data Quality Objective Process (Equipment DQO) (Bloom 1996). The Tank Characterization Technical Sampling Basis document (Brown et al. 1998) indicates that these issues, except the Equipment DQO apply to tank 241-AZ-102 for this sampling event. The Equipment DQO is applied for shear strength measurements of the solids segments only. Poppiti (1999) requires additional americium-241 analyses of the sludge segments. Brown et al. (1998) also identify safety screening, regulatory issues and provision of samples to the Privatization Contractor(s) as applicable issues for this tank. However, these issues will not be addressed via this sampling event. Reynolds et al. (1999) concluded that information from previous sampling events was sufficient to satisfy the safety screening requirements for tank 241-AZ-102. Push mode core samples will be obtained from risers 15C and 24A to provide sufficient material for the chemical analyses and tests required to satisfy these data quality objectives. The 222-S Laboratory will extrude core samples, composite the liquids and solids, perform chemical analyses

Ice Lens Formation and Frost Heave at the Phoenix Landing Site

Science.gov (United States)

Zent, A. P.; Sizemore, H. G.; Remple, A. W.

2011-01-01

Several lines of evidence indicate that the volume of shallow ground ice in the martian high latitudes exceeds the pore volume of the host regolith. Boynton et al. found an optimal fit to the Mars Odyssey Gamma Ray Spectrometer (GRS) data at the Phoenix landing site by modeling a buried layer of 50-75% ice by mass (up to 90% ice by volume). Thermal and optical observations of recent impact craters in the northern hemisphere have revealed nearly pure ice. Ice deposits containing only 1-2% soil by volume were excavated by Phoenix. The leading hypothesis for the origin of this excess ice is that it developed in situ by a mechanism analogous to the formation of terrestrial ice lenses and needle ice. Problematically, terrestrial soil-ice segregation is driven by freeze/thaw cycling and the movement of bulk water, neither of which are expected to have occurred in the geologically recent past on Mars. If however ice lens formation is possible at temperatures less than 273 K, there are possible implications for the habitability of Mars permafrost, since the same thin films of unfrozen water that lead to ice segregation are used by terrestrial psychrophiles to metabolize and grow down to temperatures of at least 258 K.

Morning Frost in Trench Dug by Phoenix, Sol 113 (False Color)

Science.gov (United States)

2008-01-01

This image from the Surface Stereo Imager on NASA's Phoenix Mars Lander shows morning frost inside the 'Snow White' trench dug by the lander, in addition to subsurface ice exposed by use of a rasp on the floor of the trench. The camera took this image at about 9 a.m. local solar time during the 113th Martian day of the mission (Sept. 18, 2008). Bright material near and below the four-by-four set of rasp holes in the upper half of the image is water-ice exposed by rasping and scraping in the trench earlier the same morning. Other bright material especially around the edges of the trench, is frost. Earlier in the mission, when the sun stayed above the horizon all night, morning frost was not evident in the trench. This image is presented in false color that enhances the visibility of the frost. The trench is 4 to 5 centimeters (about 2 inches) deep, about 23 centimeters (9 inches) wide. Phoenix landed on a Martian arctic plain on May 25, 2008. The mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is led by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development was by Lockheed Martin Space Systems, Denver.

Radio variability in the Phoenix Deep Survey at 1.4 GHz

Science.gov (United States)

Hancock, P. J.; Drury, J. A.; Bell, M. E.; Murphy, T.; Gaensler, B. M.

2016-09-01

We use archival data from the Phoenix Deep Survey to investigate the variable radio source population above 1 mJy beam-1 at 1.4 GHz. Given the similarity of this survey to other such surveys we take the opportunity to investigate the conflicting results which have appeared in the literature. Two previous surveys for variability conducted with the Very Large Array (VLA) achieved a sensitivity of 1 mJy beam-1. However, one survey found an areal density of radio variables on time-scales of decades that is a factor of ˜4 times greater than a second survey which was conducted on time-scales of less than a few years. In the Phoenix deep field we measure the density of variable radio sources to be ρ = 0.98 deg-2 on time-scales of 6 months to 8 yr. We make use of Wide-field Infrared Survey Explorer infrared cross-ids, and identify all variable sources as an active galactic nucleus of some description. We suggest that the discrepancy between previous VLA results is due to the different time-scales probed by each of the surveys, and that radio variability at 1.4 GHz is greatest on time-scales of 2-5 yr.

Lactancia materna, alimentación artificial y el primer contacto con azúcar

Directory of Open Access Journals (Sweden)

Fabian Calixto Fraiz

2013-01-01

Full Text Available Objetivo: Este estudio evaluó los cambios en el patrón de lactancia materna, alimentación artificial y en la introducción de azúcar en la dieta de niños de 0 a 36 meses, a través de dos estudios, con un intervalo de 13 años en la ciudad de Curitiba, Paraná, Brasil. Material y métodos: Poblaciones semejantes de una misma región geográfica fueron evaluadas a través de un cuestionario, en los años de 1993 y 2006, envolviendo, respectivamente, las madres de 180 y 94 niños. Introducción de azúcar en la dieta fue considerada precoz cuando ocurrió antes del 6º mes completo de vida. Los datos fueron analizados estadísticamente a través del test de qui-cuadrado y test exacto de Fisher (α= 0,05. Resultados: Hubo diferencias en la frecuencia del primer contacto con azúcar (p <0,001, que ocurrió en el primer mes de vida en 61,7% de los niños del primer estudio y en sólo 3,2% de los niños del segundo estudio. Hubo diferencias en el patrón de lactancia materna (p = 0,02, siendo la prevalencia de niños amamantados mayor en el segundo estudio. No fueron encontradas diferencias estadísticamente significativas en la prevalencia de uso de biberón, uso de biberón durante la noche y lactancia materna durante la noche, así como en el uso de biberón conteniendo azúcar. Conclusiones: Estos resultados indican que la lactancia materna puede, además de sus varias ventajas, también promover el aplazamiento de la introducción de azúcar en la dieta infantil. Nuevas investigaciones son necesarias para confirmar esta hipótesis.

Enrique Díaz and Present Phpotographies (From Graphic Notes to Photo-essays

Directory of Open Access Journals (Sweden)

Rebeca Monroy Nasr

1998-10-01

Full Text Available With "Enrique Díaz and Present Phpotographies (From Graphic Notes to Photo-essays ", the author presents part of our photo­graphic history, as well as some aspects of its development as a form of journalism and of art. She rescues the figure of Enrique Díaz Reyna as representative of the union of graphic journalists, due to his technical, formal and conceptual traits, all of them tools with which he opened important paths and innovative graphical and aesthetic proposals. This essay presents some aspects of the graphic journalist's work in Mexico City, from the twenties to the forties. As a guide to the photographer's extensi­ve work, the author reviews some of the proposals he made as his work became more mature: first, the graphic note, later, recrea­ting the photo-reportage, and finally, exploring with photoessays. Thus, attention is centered particularly on Díaz Reyna's visual language, where the signs of a distinctive modernity appro­priate of his time allow us to understand a substantial part of the transition towards a contemporary and  truly national photo-journalism.

Anticorrosive magnesium hydroxide coating on AZ31 magnesium alloy by hydrothermal method

International Nuclear Information System (INIS)

Zhu Yanying; Wu Guangming; Xing Guangjian; Li Donglin; Zhao Qing; Zhang Yunhong

2009-01-01

Magnesium alloys are potential biodegradable biomaterials in orthopedic surgery. However, the rapid degradation rate has limited their application in biomedical field. A great deal of studies have been done to improve the resistance of magnesium alloys. In this article, An anticorrosive magnesium hydroxide coating with a thickness of approximately 100μm was formed on an AZ31 magnesium alloy by hydrothermal method. The morphology of the coatings were observed by an optical microscope and SEM. And the samples were soaked in hank's solution (37 deg. C) to investigate the corrosion resistance. Magnesium alloy AZ31 with magnesium hydroxide coatings present superior corrosion resistance than untreated samples.

Targeted therapies for diarrhea-predominant irritable bowel syndrome

OpenAIRE

Olden, Kevin W

2012-01-01

Kevin W OldenDepartment of Medicine, St Joseph's Hospital and Medical Center, Phoenix, AZ, USAAbstract: Irritable bowel syndrome (IBS) causes gastrointestinal symptoms such as abdominal pain, bloating, and bowel pattern abnormalities, which compromise patients' daily functioning. Common therapies address one or two IBS symptoms, while others offer wider symptom control, presumably by targeting pathophysiologic mechanisms of IBS. The aim of this targeted literature review was t...

Migración y desigualdad laboral y salarial por género y estatus migratorio de las sinaloenses en Phoenix, Arizona

Directory of Open Access Journals (Sweden)

Erika Montoya Zavala

2011-01-01

Full Text Available Para analizar la participación de las sinaloenses emigrantes en el mercado laboral en las comunidades de destino, las implicaciones de género y estatus migratorio en el tipo de empleo y sus salarios se estudiaron las características de mujeres y hombres emigrantes de Sinaloa, y se contrastaron con las de las sonorenses radicadas en Phoenix. Esta investigación se basó en la encuesta a hogares mexicanos en Phoenix, de 2007.

A Storable, Hybrid Mars Ascent Vehicle Technology Demonstrator for the 2020 Launch Opportunity

Science.gov (United States)

Chandler, A. A.; Karabeyoglu, M. A.; Cantwell, B. J.; Reeve, R.; Goldstein, B. G.; Hubbard, G. S.

2012-06-01

A Phoenix sized mission including a reduced payload, two-stage, hybrid Mars Ascent Vehicle technology demonstrator is proposed for the 2020 opportunity. The hybrid MAV is storable on Mars and would retire risk for a Mars Sample Return campaign.

The effects of zirconium and beryllium on microstructure evolution, mechanical properties and corrosion behaviour of as-cast AZ63 alloy

International Nuclear Information System (INIS)

Jafari, Hassan; Amiryavari, Peyman

2016-01-01

Alloying elements are able to strongly modify the microstructure characteristics of Mg–Al–Zn alloys which dominate mechanical and corrosion properties of the alloys. In this research, the individual effects of Zr and Be additions on the microstructure, mechanical and corrosion properties of as-cast AZ63 alloy were explored. The results revealed that the addition of Zr leads to microstructure refinement in as-cast AZ63 alloy, resulting in improved tensile and hardness properties. 0.0001 and 0.001 wt% Be containing cast AZ63 alloy exhibited microstructure coarsening, while morphological alteration from sixford symmetrical to irregular shape grain was observed for the alloy containing 0.01 and 0.1 wt% Be. No specific Be compound was detected. In addition, mechanical properties of AZ63 alloy containing Zr was improved due to the microstructure modification, while Be containing alloy responded reverse behaviour. The corrosion resistance of AZ63 alloy was improved after the addition of Zr and Be due to the grain refinement and passivation effects, respectively. However, when the Zr content exceeds 0.5 wt%, the formation of Al 2 Zr affected the corrosion resistance. In other words, AZ63–0.5Zr alloy provided the lowest corrosion rate.

The Effects of Rare Earth Pr and Heat Treatment on the Wear Properties of AZ91 Alloy

Directory of Open Access Journals (Sweden)

Ning Li

2018-06-01

Full Text Available This paper investigated the influences of Pr addition and heat treatment (T6 on the dry sliding wear behavior of AZ91 alloy. The wear rates and friction coefficients were measured by using a pin-on-disc tribometer under loads of 30, 60 and 90 N at dry sliding speeds of 100 rpm, over a sliding time of 15 min. The worn surfaces were examined using a scanning electron microscope and was analyzed with an energy dispersive spectrometer. The experimental results revealed that AZ91-1.0%Pr magnesium alloy exhibited lower wear rate and friction coefficient than the other investigated alloys. As the applied load increased, the wear rate and friction coefficient increased. Compared with the as-cast AZ91-1.0%Pr magnesium alloy, the hardness and wear resistance of the alloy after solution treatment were reduced, and through the subsequent aging, the hardness and wear resistance of the alloy were improved and the hardness was 101.1 HB (compared to as-cast AZ91 magnesium alloy, it increased by 45%. The AZ91-1.0%Pr with T6 magnesium alloy exhibited best wear resistance. Abrasion was dominant at load of 30 N, delamination was dominant at load of 60 N and plastic deformation was dominant at load of 90 N. Oxidation was observed at all loads.

Effect of thermal tempering on microstructure and mechanical properties of Mg-AZ31/Al-6061 diffusion bonding

Energy Technology Data Exchange (ETDEWEB)

Jafarian, Mojtaba [Young Researchers and Elite Club, Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Rizi, Mohsen Saboktakin, E-mail: M.saboktakin@Pa.iut.ac.ir [Department of Materials Engineering, Isfahan University of Technology, Isfahan 8415683111 (Iran, Islamic Republic of); Department of Industrial Engineering, Lenjan Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of); Jafarian, Morteza [Young Researchers and Elite Club, Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Honarmand, Mehrdad [Department of Mechanical Engineering, Tiran Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of); Javadinejad, Hamid Reza; Ghaheri, Ali [Department of Materials Engineering, Isfahan University of Technology, Isfahan 8415683111 (Iran, Islamic Republic of); Department of Industrial Engineering, Lenjan Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of); Bahramipour, Mohammad Taghi [Materials Engineering Department, Hakim Sabzevari University, Sabzevar, 397 (Iran, Islamic Republic of); Ebrahimian, Marzieh [Department of Materials Engineering, Isfahan University of Technology, Isfahan 8415683111 (Iran, Islamic Republic of); Department of Industrial Engineering, Lenjan Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of)

2016-06-01

The objective of this study is to investigate the effect of the types thermal tempering of aluminum alloy on microstructure and mechanical properties of AZ31-O Mg and Al 6061-T6 diffusion bonding. Using Optical Microscope (OM) and Scanning Electron Microscopes (SEM) equipped with EDS analysis and line scan the interfaces of joints were evaluated. The XRD analysis was carried out to characterize phase constitution near the interface zone. The mechanical properties of joints were measured using Vickers micro-hardness and shear strength. According to the results in bonding of AZ31-Mg/Al-6061-O, in less plastic deformation in magnesium alloy, diffusion rate of most magnesium atoms occurred to aluminum alloy and formation of diffusion zone with minimum micro-hardness (140 HV) and maximum shear strength (32 MPa) compared to Al 6061-T6/Mg-AZ31 bonding. Evaluation of fracture surfaces indicates an occurrence of failure from the brittle intermetallic phases. - Highlights: • Diffusion bonding AZ31 to Al-6061withoutany interlayer was successful. • Thermal tempered aluminum alloy plays a vital role in the mechanical properties of joint. • Less thickness of reaction layers and micro-hardness in bonding annealed Al- 6061 layers to AZ31 was achieved. • Fracture surfaces indicated that the onset of fracture from intermetallic compounds resulted in fracture of the cleavage.

Multivalent binding of PWWP2A to H2A.Z regulates mitosis and neural crest differentiation.

Science.gov (United States)

Pünzeler, Sebastian; Link, Stephanie; Wagner, Gabriele; Keilhauer, Eva C; Kronbeck, Nina; Spitzer, Ramona Mm; Leidescher, Susanne; Markaki, Yolanda; Mentele, Edith; Regnard, Catherine; Schneider, Katrin; Takahashi, Daisuke; Kusakabe, Masayuki; Vardabasso, Chiara; Zink, Lisa M; Straub, Tobias; Bernstein, Emily; Harata, Masahiko; Leonhardt, Heinrich; Mann, Matthias; Rupp, Ralph Aw; Hake, Sandra B

2017-08-01

Replacement of canonical histones with specialized histone variants promotes altering of chromatin structure and function. The essential histone variant H2A.Z affects various DNA-based processes via poorly understood mechanisms. Here, we determine the comprehensive interactome of H2A.Z and identify PWWP2A as a novel H2A.Z-nucleosome binder. PWWP2A is a functionally uncharacterized, vertebrate-specific protein that binds very tightly to chromatin through a concerted multivalent binding mode. Two internal protein regions mediate H2A.Z-specificity and nucleosome interaction, whereas the PWWP domain exhibits direct DNA binding. Genome-wide mapping reveals that PWWP2A binds selectively to H2A.Z-containing nucleosomes with strong preference for promoters of highly transcribed genes. In human cells, its depletion affects gene expression and impairs proliferation via a mitotic delay. While PWWP2A does not influence H2A.Z occupancy, the C-terminal tail of H2A.Z is one important mediator to recruit PWWP2A to chromatin. Knockdown of PWWP2A in Xenopus results in severe cranial facial defects, arising from neural crest cell differentiation and migration problems. Thus, PWWP2A is a novel H2A.Z-specific multivalent chromatin binder providing a surprising link between H2A.Z, chromosome segregation, and organ development. © 2017 The Authors.

Effect of thermal tempering on microstructure and mechanical properties of Mg-AZ31/Al-6061 diffusion bonding

International Nuclear Information System (INIS)

Jafarian, Mojtaba; Rizi, Mohsen Saboktakin; Jafarian, Morteza; Honarmand, Mehrdad; Javadinejad, Hamid Reza; Ghaheri, Ali; Bahramipour, Mohammad Taghi; Ebrahimian, Marzieh

2016-01-01

The objective of this study is to investigate the effect of the types thermal tempering of aluminum alloy on microstructure and mechanical properties of AZ31-O Mg and Al 6061-T6 diffusion bonding. Using Optical Microscope (OM) and Scanning Electron Microscopes (SEM) equipped with EDS analysis and line scan the interfaces of joints were evaluated. The XRD analysis was carried out to characterize phase constitution near the interface zone. The mechanical properties of joints were measured using Vickers micro-hardness and shear strength. According to the results in bonding of AZ31-Mg/Al-6061-O, in less plastic deformation in magnesium alloy, diffusion rate of most magnesium atoms occurred to aluminum alloy and formation of diffusion zone with minimum micro-hardness (140 HV) and maximum shear strength (32 MPa) compared to Al 6061-T6/Mg-AZ31 bonding. Evaluation of fracture surfaces indicates an occurrence of failure from the brittle intermetallic phases. - Highlights: • Diffusion bonding AZ31 to Al-6061withoutany interlayer was successful. • Thermal tempered aluminum alloy plays a vital role in the mechanical properties of joint. • Less thickness of reaction layers and micro-hardness in bonding annealed Al- 6061 layers to AZ31 was achieved. • Fracture surfaces indicated that the onset of fracture from intermetallic compounds resulted in fracture of the cleavage.

Systematic understanding of corrosion behavior of plasma electrolytic oxidation treated AZ31 magnesium alloy using a mouse model of subcutaneous implant

Energy Technology Data Exchange (ETDEWEB)

Jang, Yongseok [Engineering Research Center for Revolutionizing Metallic Biomaterials (ERC-RMB), North Carolina A and T State University, Greensboro, NC, 27411 (United States); Tan, Zongqing [Internal Medicine, College of Medicine, University of Cincinnati, OH 45211 (United States); Jurey, Chris [Luke Engineering, Wadsworth, OH 44282 (United States); Collins, Boyce [Engineering Research Center for Revolutionizing Metallic Biomaterials (ERC-RMB), North Carolina A and T State University, Greensboro, NC, 27411 (United States); Badve, Aditya [Business and Biology, The University of North Carolina at Chapel Hill, NC 27514 (United States); Dong, Zhongyun [Internal Medicine, College of Medicine, University of Cincinnati, OH 45211 (United States); Park, Chanhee; Kim, Cheol Sang [Department of Bio-nano System Engineering, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Sankar, Jagannathan [Engineering Research Center for Revolutionizing Metallic Biomaterials (ERC-RMB), North Carolina A and T State University, Greensboro, NC, 27411 (United States); Yun, Yeoheung, E-mail: yyun@ncat.edu [Engineering Research Center for Revolutionizing Metallic Biomaterials (ERC-RMB), North Carolina A and T State University, Greensboro, NC, 27411 (United States)

2014-12-01

This study was conducted to identify the differences between corrosion rates, corrosion types, and corrosion products in different physiological environments for AZ31 magnesium alloy and plasma electrolytic oxidation (PEO) treated AZ31 magnesium alloy. In vitro and in vivo tests were performed in Hank's Balanced Salt Solution (HBSS) and mice for 12 weeks, respectively. The corrosion rates of both AZ31 magnesium alloy and PEO treated AZ31 magnesium alloy were calculated based on DC polarization curves, volume of hydrogen evolution, and the thickness of corrosion products formed on the surface. Micro X-ray computed tomography (Micro-CT), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) were used to analyze morphological and chemical characterizations of corrosion products. The results show that there is more severe localized corrosion after in vitro test in HBSS; however, the thicknesses of corrosion products formed on the surface for AZ31 magnesium alloy and PEO treated AZ31 magnesium alloy in vivo were about 40% thicker than the thickness of corrosion products generated in vitro. The ratio of Ca and P (Ca/P) in the corrosion products also differed. The Ca deficient region and higher content of Al in corrosion product than AZ31 magnesium alloy were identified after in vivo test in contrast with the result of in vitro test. - Highlights: • Effects of plasma electrolytic oxidation on AZ31 in vitro and in vivo • Retardation of degradation via plasma electrolytic oxidation in vitro and in vivo • Differentiation of in vitro and in vivo corrosion types and products.

Systematic understanding of corrosion behavior of plasma electrolytic oxidation treated AZ31 magnesium alloy using a mouse model of subcutaneous implant

International Nuclear Information System (INIS)

Jang, Yongseok; Tan, Zongqing; Jurey, Chris; Collins, Boyce; Badve, Aditya; Dong, Zhongyun; Park, Chanhee; Kim, Cheol Sang; Sankar, Jagannathan; Yun, Yeoheung

2014-01-01

This study was conducted to identify the differences between corrosion rates, corrosion types, and corrosion products in different physiological environments for AZ31 magnesium alloy and plasma electrolytic oxidation (PEO) treated AZ31 magnesium alloy. In vitro and in vivo tests were performed in Hank's Balanced Salt Solution (HBSS) and mice for 12 weeks, respectively. The corrosion rates of both AZ31 magnesium alloy and PEO treated AZ31 magnesium alloy were calculated based on DC polarization curves, volume of hydrogen evolution, and the thickness of corrosion products formed on the surface. Micro X-ray computed tomography (Micro-CT), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) were used to analyze morphological and chemical characterizations of corrosion products. The results show that there is more severe localized corrosion after in vitro test in HBSS; however, the thicknesses of corrosion products formed on the surface for AZ31 magnesium alloy and PEO treated AZ31 magnesium alloy in vivo were about 40% thicker than the thickness of corrosion products generated in vitro. The ratio of Ca and P (Ca/P) in the corrosion products also differed. The Ca deficient region and higher content of Al in corrosion product than AZ31 magnesium alloy were identified after in vivo test in contrast with the result of in vitro test. - Highlights: • Effects of plasma electrolytic oxidation on AZ31 in vitro and in vivo • Retardation of degradation via plasma electrolytic oxidation in vitro and in vivo • Differentiation of in vitro and in vivo corrosion types and products

The effect of PVD coatings on the corrosion behaviour of AZ91 magnesium alloy

International Nuclear Information System (INIS)

Altun, Hikmet; Sen, Sadri

2006-01-01

In this study, multilayered AlN (AlN + AlN + AlN) and AlN + TiN were coated on AZ91 magnesium alloy using physical vapour deposition (PVD) technique of DC magnetron sputtering, and the influence of the coatings on the corrosion behaviour of the AZ91 alloy was examined. A PVD system for coating processes, a potentiostat for electrochemical corrosion tests, X-ray difractometer for compositional analysis of the coatings, and scanning electron microscopy for surface examinations were used. It was determined that PVD coatings deposited on AZ91 magnesium alloy increased the corrosion resistance of the alloy, and AlN + AlN + AlN coating increased the corrosion resistance much more than AlN + TiN coating. However, it was observed that, in the coating layers, small structural defects e.g., pores, pinholes, cracks that could arise from the coating process or substrate and get the ability of protection from corrosion worsened were present

In vitro corrosion of magnesium alloy AZ31 — a synergetic influence of glucose and Tris

Science.gov (United States)

Li, Ling-Yu; Liu, Bin; Zeng, Rong-Chang; Li, Shuo-Qi; Zhang, Fen; Zou, Yu-Hong; Jiang, Hongwei George; Chen, Xiao-Bo; Guan, Shao-Kang; Liu, Qing-Yun

2018-05-01

Biodegradable Mg alloys have generated great interest for biomedical applications. Accurate predictions of in vivo degradation of Mg alloys through cost-effective in vivo evaluations require the latter to be conducted in an environment close to that of physiological scenarios. However, the roles of glucose and buffering agents in regulating the in vivo degradation performance of Mg alloys has not been elucidated. Herein, degradation behavior of AZ31 alloy is investigated by hydrogen evolution measurements, pH monitoring and electrochemical tests. Results indicate that glucose plays a content-dependent role in degradation of AZ31 alloy in buffer-free saline solution. The presence of a low concentration of glucose, i.e. 1.0 g/L, decreases the corrosion rate of Mg alloy AZ31, whereas the presence of 2.0 and 3.0 g/L glucose accelerates the corrosion rate during long term immersion in saline solution. In terms of Tris-buffered saline solution, the addition of glucose increases pH value and promotes pitting corrosion or general corrosion of AZ31 alloy. This study provides a novel perspective to understand the bio-corrosion of Mg alloys in buffering agents and glucose containing solutions.

Augmenting the Energy-Saving Impact of IEEE 802.3az via the Control Plane

OpenAIRE

Thaenchaikun , Chakadkit; Jakllari , Gentian; Paillassa , Béatrice

2015-01-01

International audience; IEEE 802.3az, the recent standard for Energy Efficient Ethernet, is one of the main contributions of the ICT industry to the global quest for energy efficiency. Energy consumption reduction is accomplished by essentially replacing the continuous IDLE of legacy IEEE 802.3 cards with a Low Power Idle. While this is an important step in the right direction, studies have shown that the energy saving with IEEE 802.3az highly depends on the traffic load and stops for link ut...

Systematic understanding of corrosion behavior of plasma electrolytic oxidation treated AZ31 magnesium alloy using a mouse model of subcutaneous implant.

Science.gov (United States)

Jang, Yongseok; Tan, Zongqing; Jurey, Chris; Collins, Boyce; Badve, Aditya; Dong, Zhongyun; Park, Chanhee; Kim, Cheol Sang; Sankar, Jagannathan; Yun, Yeoheung

2014-12-01

This study was conducted to identify the differences between corrosion rates, corrosion types, and corrosion products in different physiological environments for AZ31 magnesium alloy and plasma electrolytic oxidation (PEO) treated AZ31 magnesium alloy. In vitro and in vivo tests were performed in Hank's Balanced Salt Solution (HBSS) and mice for 12 weeks, respectively. The corrosion rates of both AZ31 magnesium alloy and PEO treated AZ31 magnesium alloy were calculated based on DC polarization curves, volume of hydrogen evolution, and the thickness of corrosion products formed on the surface. Micro X-ray computed tomography (Micro-CT), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) were used to analyze morphological and chemical characterizations of corrosion products. The results show that there is more severe localized corrosion after in vitro test in HBSS; however, the thicknesses of corrosion products formed on the surface for AZ31 magnesium alloy and PEO treated AZ31 magnesium alloy in vivo were about 40% thicker than the thickness of corrosion products generated in vitro. The ratio of Ca and P (Ca/P) in the corrosion products also differed. The Ca deficient region and higher content of Al in corrosion product than AZ31 magnesium alloy were identified after in vivo test in contrast with the result of in vitro test. Copyright © 2014 Elsevier B.V. All rights reserved.

Warm Deep Drawing of Rectangular Parts of AZ31 Magnesium Alloy Sheet Adopting Variable Blank Holder Force

International Nuclear Information System (INIS)

Peng Yinghong; Chang Qunfeng; Li Dayong; Zeng Xiaoqin

2007-01-01

AZ31 magnesium alloy sheet with good shape and formability is fabricated by warm cross rolling. Uniaxial tensile tests are conducted using a Gleeble 3500 thermal - mechanical simulator, and the mechanical properties of AZ31 magnesium alloy sheet are analyzed. A warm deep drawing process of square part is also simulated by the finite element method. The influences of blank holder force on the formability are numerically investigated. A double-action hydraulic press that can realize adjustable blank holder forces is developed and its working principle and control system are introduced. Some warm deep drawing experiments of square parts of AZ31 magnesium alloy sheet are also performed. Different variation schemes of the blank holder force with the stroke of the punch are tested, and the experiment results are compared. Results show that the suitable blank holder force variation scheme is a ladder curve with the punch stroke. Adopting the variable blank holder force technique can improve 13.2% of the drawing depth of square parts of AZ31 magnesium alloy sheet

Synthesis and biological evaluation of [11C]AZ12504948; a novel tracer for imaging of glucokinase in pancreas and liver

International Nuclear Information System (INIS)

Jahan, M.; Johnström, P.; Nag, S.; Takano, A.; Korsgren, O.; Johansson, L.; Halldin, C.; Eriksson, O.

2015-01-01

Introduction: Glucokinase (GK) is potentially a target for imaging of islets of Langerhans. Here we report the radiosynthesis and preclinical evaluation of the GK activator, [ 11 C]AZ12504948, for in vivo imaging of GK. Methods: [ 11 C]AZ12504948 was synthesized by O-methylation of the precursor, AZ125555620, using carbon-11 methyl iodide ([ 11 C]CH 3 I). Preclinical evaluation was performed by autoradiography (ARG) of human tissues and PET/CT studies in pig and non-human primate. Result: [ 11 C]AZ12504948 was produced in reproducible good radiochemical yield in 28–30 min. Radiochemical purity of the formulated product was > 98% for up to 2 h with specific radioactivities 855 ± 209 GBq/μmol (n = 8). The preclinical evaluation showed some specificity for GK in liver, but not in pancreas. Conclusion: [ 11 C]AZ12504948 images GK in liver, but the low specificity impedes the visualization of GK in pancreas. Improved target specificity is required for further progress using PET probes based on this class of GK activators

Neutron radiography at the University of Michigan's Phoenix Memorial Laboratory

International Nuclear Information System (INIS)

Lindsay, J.T.; Elam, S.; Koblish, T.; Lee, P.; McAuliffe, D.

1990-01-01

Real-time neutron radiography (RTNR) is rapidly becoming a valuable tool for nondestructive testing and basic research with a wide variety of applications. The Phoenix Memorial Laboratory (PML) at the University of Michigan has developed an RTNR facility and has been using this facility to study several phenomena of interest to researchers in many areas. These phenomena include imaging of the internal fluid flow in gas turbine engine nozzles and coking and debris deposition in several gas turbine nozzles. This paper presents a summary of the technique and facilities involved in these applications

Troubles continue for the Phoenix VA

Directory of Open Access Journals (Sweden)

Robbins RA

2014-10-01

Full Text Available No abstract available. Article truncated after 150 words. According to the Joint Commission on the Accreditation of Healthcare Organizations (Joint Commission, JCAHO, an independent organization that reviews hospitals, the Phoenix VA does not comply with U.S. standards for safety, patient care and management (1. The hospital was at the epicenter of the national scandal over the quality of care being afforded to the nation's veterans where the now notorious practice of double-booking patient appointments was first exposed. The hospital's indifferent management provoked congressional investigations that uncovered still more system-wide abuses leading to the removal of the hospital director and the resignation of then VA secretary, Eric Shinseki. The hospital maintains its accreditation but with a follow-up survey in 1-6 months where it must show that it has successfully addressed the 13 identified problems (1. Inspectors who conducted the review in July found that VA employees were unable to report concerns "without retaliatory action from the hospital." Other alarming ...

Tank 241-AZ-102 Privatization Push Mode Core Sampling and Analysis Plan

International Nuclear Information System (INIS)

TEMPLETON, A.M.

1999-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AZ-102

Tank 241-AZ-102 Privatization Push Mode Core Sampling and Analysis Plan

International Nuclear Information System (INIS)

RASMUSSEN, J.H.

2000-01-01

This sampling and analysis plan (SAP) identifies characterization objectives pertaining to sample collection, laboratory analytical evaluation, and reporting requirements for samples obtained from tank 241-AZ-102

78 FR 34403 - Notice of Availability of the Record of Decision for the Quartzsite Solar Energy Project, AZ

Science.gov (United States)

2013-06-07

...; AZA34666] Notice of Availability of the Record of Decision for the Quartzsite Solar Energy Project, AZ... Solar Energy Project (QSEP). The Acting Assistant Secretary for Land and Minerals Management approved...: http://www.blm.gov/az/st/en/prog/energy/solar/quartzsite_solar_energy.html . FOR FURTHER INFORMATION...

Development of a Ballistic Specification for Magnesium Alloy AZ31B

National Research Council Canada - National Science Library

Jones, Tyrone L; DeLorme, Richard D

2008-01-01

The U.S. Army Research Laboratory (ARL) and Magnesium Elektron North America (MENA) have conducted a joint effort to develop and evaluate rolled plate in commercially available magnesium alloy-temper AZ31B-H24...

Interfacial microstructure and mechanical properties of Cf/AZ91D composites with TiO2 and PyC fiber coatings.

Science.gov (United States)

Li, Shaolin; Qi, Lehua; Zhang, Ting; Ju, Luyan; Li, Hejun

2017-10-01

In spite of the effectiveness of the fiber coatings on interface modification of carbon fiber reinforced magnesium matrix composites, the cost and exclusive equipment for the coatings preparation are usually ignored during research work. In this paper, pyrolytic carbon (PyC) and TiO 2 were coated on carbon fiber surface to study the effects of fiber coatings on interfacial microstructure and mechanical properties of carbon fiber reinforced AZ91D composites (C f /AZ91D composites). It was indicated that both the two coatings could modify the interface and improve the mechanical properties of the composites. The ultimate tensile strength of the TiO 2 -C f /AZ91D and the PyC-C f /AZ91D composite were 333MPa and 400MPa, which were improved by 41.7% and 70.2% respectively, compared with the untreated-C f /AZ91D composite. The microstructure observation revealed that the strengthening of the composites relied on fiber integrity and moderate interfacial bonding. MgO nano-particles were generated at the interface due to the reaction of TiO 2 with Mg in the TiO 2 -C f /AZ91D composite. The volume expansion resulting from the reaction let to disordered intergranular films and crystal defects at the interface. The fibers were protected and the interfacial reaction was restrained by PyC coating in the PyC-C f /AZ91D composite. The principle to select the coating of fiber was proposed by comparing the effectiveness and cost of the coatings. Copyright © 2017 Elsevier Ltd. All rights reserved.

Correlative change of corrosion behavior with the microstructure of AZ91 Mg alloy modified with Y additions

International Nuclear Information System (INIS)

Jia, Ruiling; Zhang, Ming; Zhang, Lina; Zhang, Wei; Guo, Feng

2015-01-01

Highlights: • The effect of Y addition into the AZ91 Mg alloys was investigated. • Initial stage of corrosion was studied by in-situ 3D digital microscopy observation. • The potential difference was investigated by Kelvin probe force microscopy. • The effect of Y addition on the corrosion mechanisms of AZ91 alloy was studied. - Abstract: Microstructure characterization of the AZ91 magnesium alloys with or without rare earth element yttrium (Y) has been revealed by SEM, EDS and EPMA. Some Y-rich phases can be found in the magnesium alloys with Y additions. The fraction of β-Mg 17 Al 12 phase obvious decreases and turns into granular distribution with the increase of Y addition instead of original wet distribution along grain boundaries. The results of the potentiodynamic polarization tests show that the corrosion resistance of AZ91 alloy is improved with appropriate Y additions. But an in-situ observation of 3D digital microscopy for the initial stage of corrosion of the magnesium alloy with 0.9%Y addition shows that Y-rich phases act as cathodic effect and the α phases in the vicinity of them acting as anode are corroded. So the additions of Y have a beneficial effect that can depress the overall corrosion of AZ91 alloy, whereas its harmful effect is related to Y-rich phases because they present the highest Volta potential difference from the adjacent matrix and they can drive galvanic corrosion

Correlative change of corrosion behavior with the microstructure of AZ91 Mg alloy modified with Y additions

Energy Technology Data Exchange (ETDEWEB)

Jia, Ruiling, E-mail: jrl014014@163.com [College of Materials Science and Engineering, Inner Mongolia University of Technology, Hohhot, Inner Mongolia 010051 (China); Zhang, Ming; Zhang, Lina [College of Materials Science and Engineering, Inner Mongolia University of Technology, Hohhot, Inner Mongolia 010051 (China); Zhang, Wei [Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, 62 Wencui Road, Shenyang 110016 (China); Guo, Feng [College of Materials Science and Engineering, Inner Mongolia University of Technology, Hohhot, Inner Mongolia 010051 (China)

2015-06-15

Highlights: • The effect of Y addition into the AZ91 Mg alloys was investigated. • Initial stage of corrosion was studied by in-situ 3D digital microscopy observation. • The potential difference was investigated by Kelvin probe force microscopy. • The effect of Y addition on the corrosion mechanisms of AZ91 alloy was studied. - Abstract: Microstructure characterization of the AZ91 magnesium alloys with or without rare earth element yttrium (Y) has been revealed by SEM, EDS and EPMA. Some Y-rich phases can be found in the magnesium alloys with Y additions. The fraction of β-Mg{sub 17}Al{sub 12} phase obvious decreases and turns into granular distribution with the increase of Y addition instead of original wet distribution along grain boundaries. The results of the potentiodynamic polarization tests show that the corrosion resistance of AZ91 alloy is improved with appropriate Y additions. But an in-situ observation of 3D digital microscopy for the initial stage of corrosion of the magnesium alloy with 0.9%Y addition shows that Y-rich phases act as cathodic effect and the α phases in the vicinity of them acting as anode are corroded. So the additions of Y have a beneficial effect that can depress the overall corrosion of AZ91 alloy, whereas its harmful effect is related to Y-rich phases because they present the highest Volta potential difference from the adjacent matrix and they can drive galvanic corrosion.

Phoenix light - Heating and cooling with phase-change materials; Phoenix light: Heizen und Kuehlen mit PCM - Schlussbericht

Energy Technology Data Exchange (ETDEWEB)

Haechler, E. [Suiselectra Ingenieurunternehmung AG, Basel (Switzerland); Schneider, B. [Hochschule Esslingen, University of Applied Sciences, Esslingen (Germany)

2002-12-15

This final report for the Swiss Federal Office of Energy (SFOE) deals with the use of phase-change materials (PCM) in buildings in order to help provide cooling in summer and heating in winter. General information on PCM and its use in the automotive industry, clothing, heating systems and office materials as well as in the electronics industry is provided. The physical and chemical basics are discussed and examples of PCM use in practice are provided. Also, work done in research institutes is mentioned. PCM systems from various manufacturers are noted. The 'phoenix light' system concept is discussed. The 'comfort cooler' concept is introduced and laboratory measurements made at the University of Applied Sciences in Esslingen, Germany, are discussed. Further, measurements made at an installation in an existing building are presented and discussed. Knowledge gained and the optimisation of the system are discussed. Finally, proposals for further work to be done are noted.

Comportamiento frente a la corrosión y biocompatibilidad in vitro/in vivo de la aleación AZ31 modificada superficialmente

OpenAIRE

Escudero, M. L.; Clemente, C.; Rubio, J. C.; Alobera, M. A.; García-Alonso, M. C.; del Valle, J. A.; Iglesias, C.; Pérez-Maceda, B. T.; Carboneras, M.; Lozano, R. M.

2011-01-01

The present work evaluates the corrosion behaviour and the in vitro/in vivo biocompatibility of the AZ31 magnesium alloy, which fulfills the mechanical requirements of bone. The corrosion kinetic of as-received AZ31 alloy was not compatible with the cell growth. To improve its performance, the AZ31 alloy was surface modified by a chemical conversion treatment in hydrofluoric acid. The magnesium fluoride layer generated by the surface treatment of AZ31 alloy enhances its corrosion behaviour, a...

Microstructure investigation and first-principle analysis of die-cast AZ91 alloy with calcium addition

International Nuclear Information System (INIS)

Lin, L.; Wang, F.; Yang, L.; Chen, L.J.; Liu, Z.; Wang, Y.M.

2011-01-01

Highlights: → Die-cast AZ91 with Ca addition was investigated experimentally and theoretically. → Precipitation sequence was confirmed with increasing Ca addition. → Phase stability difference was verified by first-principle calculation. → Valence configurations were associated with alloying effects of Al, Mg and Ca. - Abstract: In order to get improved mechanical properties of die-cast AZ91 alloy under elevated temperatures, Ca element was added as a cost-effective alloying constituent. It appeared that minor Ca addition less than 0.5 wt% would result in no apparent change in microstructure, but the tensile strength at elevated temperatures was improved considerably. When increasing Ca addition to more than 1.0 wt%, Al 2 Ca phase will precipitate during solidification, no Mg 2 Ca phase was discovered. Homogeneous microstructure and high temperature stability in tensile strength of die-cast AZ91 alloy with Ca addition was mainly attributed to the precipitation of Al 2 Ca phase, which considerably refined the bulky β-Mg 17 Al 12 phase distributed originally at the grain boundaries of die-cast AZ91 alloy with no Ca addition. The priority of Al 2 Ca phase compared to Mg 2 Ca phase in precipitation sequence was verified by first-principle calculation of their cohesive energy and formation enthalpy, and can also be associated with more bounding electrons between Al and Ca atoms.

78 FR 24158 - Foreign-Trade Zone (FTZ) 75-Phoenix, Arizona; Notification of Proposed Production Activity...

Science.gov (United States)

2013-04-24

... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-33-2013] Foreign-Trade Zone (FTZ) 75-Phoenix... benefits on such items. Public comment is invited from interested parties. Submissions shall be addressed... Executive Secretary, Foreign-Trade Zones Board, Room 21013, U.S. Department of Commerce, 1401 Constitution...

Nonsteroidal anti-inflammatory drug gastropathy: new avenues for safety

OpenAIRE

Roth, Sandford

2011-01-01

Sanford H RothArizona Research and Education, Arthritis Laboratory, Arizona State University, Phoenix, AZ, USAAbstract: Chronic oral or systemic nonselective nonsteroidal anti-inflammatory drug (NSAID) therapy, ubiquitously used by physicians to treat osteoarthritis-associated pain, is associated with a wide range of symptomatic adverse events, the most frequent and serious of which is gastropathy. Although cardiovascular and renal problems are a very real concern, they are significantly less...

EnviroAtlas - Phoenix, AZ - Historic Places by Census Block Group

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset portrays the total number of historic places located within each Census Block Group (CBG). The historic places data were compiled from the...

EnviroAtlas - Phoenix, AZ - 15m Riparian Buffer Forest Cover

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset describes the percentage of a 15-m riparian buffer that is forested. There is a potential for decreased water quality in areas where the...

EnviroAtlas - Phoenix, AZ - 51m Riparian Buffer Vegetated Cover

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset describes the percentage of a 51-m riparian buffer that is vegetated. There is a potential for decreased water quality in areas where the...

EnviroAtlas - Phoenix, AZ - 51m Riparian Buffer Forest Cover

Science.gov (United States)

This EnviroAtlas dataset describes the percentage of a 51-m riparian buffer that is forested. There is a potential for decreased water quality in areas where the riparian buffer is less forested. The displayed line represents the center of the analyzed riparian buffer. The water bodies analyzed include hydrologically connected streams, rivers, connectors, reservoirs, lakes/ponds, ice masses, washes, locks, and rapids within the Atlas Area. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about each attribute in this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

EnviroAtlas - Phoenix, AZ - 51m Riparian Buffer Vegetated Cover

Science.gov (United States)

This EnviroAtlas dataset describes the percentage of a 51-m riparian buffer that is vegetated. There is a potential for decreased water quality in areas where the riparian buffer is less vegetated. The displayed line represents the center of the analyzed riparian buffer. The water bodies analyzed include hydrologically connected streams, rivers, connectors, reservoirs, lakes/ponds, ice masses, washes, locks, and rapids within the Atlas Area. This dataset was produced by the US EPA to support research and online mapping activities related to EnviroAtlas. EnviroAtlas (https://www.epa.gov/enviroatlas) allows the user to interact with a web-based, easy-to-use, mapping application to view and analyze multiple ecosystem services for the contiguous United States. The dataset is available as downloadable data (https://edg.epa.gov/data/Public/ORD/EnviroAtlas) or as an EnviroAtlas map service. Additional descriptive information about each attribute in this dataset can be found in its associated EnviroAtlas Fact Sheet (https://www.epa.gov/enviroatlas/enviroatlas-fact-sheets).

EnviroAtlas - Phoenix, AZ - Greenspace Around Schools by Block Group

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas data set shows the number of schools in each block group in the EnviroAtlas community boundary as well as the number of schools where less than 25%...

EnviroAtlas - Phoenix, AZ - Estimated Intersection Density of Walkable Roads

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates the intersection density of walkable roads within a 750 meter radius of any given 10 meter pixel in the community. Intersections...

Evaluation of AY/AZ tank farm ventilation system during aging waste retrieval operations

International Nuclear Information System (INIS)

Wong, J.J.; Waters, E.D.

1995-01-01

Waste Management is currently planning to demonstrate mobilization of radioactive waste sludges in Tank 101-AZ beginning in October 1991. The retrieval system being designed will utilize mixer pumps that generate high-velocity, high-volume submerged liquid jets to mobilize settled solids. There is concern that these jets may also generate radioactive aerosols, some of which may be carried into the tank Ventilation system. The purpose of this study is to determine if the current AY/AZ ventilation system or the proposed ventilation system upgrade (Project W-030) will provide adequate deentrainment of liquid and solid aerosols during mixer pump operations, or if the radioactive aerosols will overload the HEPA filters

Influence of The Arrangement of Materials and Microstructural Analysis During FSW of AZ80A

Directory of Open Access Journals (Sweden)

Sevvel P.

2017-09-01

Full Text Available The main objective of this paper is to produce defect free weldments with improved properties during friction stir welding of dissimilar Mg alloys. The influence of the anisotropic arrangement of materials when AZ80A Mg alloy is taken as advancing side and AZ91C Mg alloy as retreating side and vice versa with respect to their mechanical properties and microstructural characteristics were investigated. The effects of various FSW parameters on the quality of these joints were also analyzed and best optimized FSW parameters were suggested. Defect free sound joints with excellent mechanical properties were produced when AZ80A Mg alloy was positioned at retreating side. At the same time, it seems a little bit difficult to obtain good quality joints with the contrary arrangement of materials. These investigations revealed that materials having inferior plastic deformability must be kept at the advancing side to obtain sound joints during FSW of dissimilar alloys of Magnesium.

A study of the deformation and failure mechanisms of protective intermetallic coatings on AZ91 Mg alloys using microcantilever bending

Energy Technology Data Exchange (ETDEWEB)

Lu, Mingyuan; Mead, James; Wu, Yueqin; Russell, Hugh; Huang, Han, E-mail: han.huang@uq.edu.au

2016-10-15

In this study, a nanoindentation-based microcantilever bending technique was utilized to investigate the interfacial properties of a β-Mg{sub 17}Al{sub 12}/AZ91 Mg alloy film/substrate system under tensile loading conditions. Finite element analysis (FEA) was first undertaken to optimise the design of cantilever structures for inducing high tensile stresses at the interface. Cantilevers consisting of a necked region or notch at the interface were determined to be the most successful designs. Microcantilevers containing the β-Mg{sub 17}Al{sub 12}/AZ91 interface were then made using focused ion beam (FIB) milling technique. Necks were made in the cantilevers to intensify the tension at the interface and notches were used to introduce a stress concentration to the interface. During bending, the cantilevers were deflected to failure. Subsequent analysis of the deformed cantilevers using electron microscopies revealed that plastic deformation, and subsequent ductile rupture, of the AZ91 phase was the dominant failure mechanism. When the β-Mg{sub 17}Al{sub 12}/AZ91 film/substrate system was subjected to tension, the softer AZ91 phase failed prior to interfacial delamination, demonstrating that the strength of the interface exceeded the stresses that caused ductile failure in the substrate material. - Highlights: •Microcantilever bending was used to study the property of film/substrate interface. •FEA was used to optimise cantilever design for achieving high interfacial tension. •The intermetallic coatings on AZ91 substrate have strong interfacial adhesion.

Study of the temporal and spatial variation of climate and solar radiation in th metropolitan Phoenix area. Final technical progress report, July 1, 1977-June 30, 1978

Energy Technology Data Exchange (ETDEWEB)

Durrenberger, R.W.

1978-09-29

The research performed was designed to identify spatial or temporal variation of any atmospheric parameters that might affect the operation of devices utilizing solar energy in the metropolitan Phoenix area. The first part of the research involved the analysis of all available solar and climatic data to determine their validity and comparability. For the standard climatic parameters, few difficulties were encountered, but the task of determining comparability of solar radiation data involved many pitfalls. It was concluded that most of the solar data acquired before January 1977 could not be used for purposes of identifying spatial variability. And, a year and a half of data does not represent a long enough period of time upon which to base sound conclusions about spatial and temporal variability of solar radiation in the metropolitan Phoenix region. The data currently available to us do not indicate any great variation of solar radiation in the metropolitan Phoenix area. However, any meaningful statements about spatial and temporal variability of solar radiation in the metropolitan Phoenix area must await the acquisition of additional data from well-calibrated equipment.

Martian Multimedia: The Agony and Ecstasy of Communicating Real-Time, Authentic Science During the Phoenix Mars Mission

Science.gov (United States)

Bitter, C.; Buxner, S. R.

2009-03-01

The Phoenix Mars Mission faced robust communication challenges requiring real-time solutions. Managing the message from Mars and ensuring the highest quality of science data and news releases were our top priorities during mission surface operations.

Date palm (Phoenix dactylifera)dispersal to the Americas: Historical evidence of the Spanish introduction

Science.gov (United States)

Date palm (Phoenix dactylifera) groves are found in the Americas from the south-west USA (36°N lat.) to Chile (21°S lat.) and eastward to the Caribbean Islands; from Venezuela, 63°W long. to 117°W long. (USA) and at elevations from 0-2,000 m. However, successful production of ripe dates is possible ...

Facebook Marketing - Fra A-Z

DEFF Research Database (Denmark)

Mortensen, Thomas Bøtker

2009-01-01

Facebook Marketing – Leverage Social Media to Grow Your Business af Steven Holzner er Facebook Marketing fra A-Z, som kan anbefales til virksomheder, som overvejer at bevæge sig ud i cyber space og afprøve mulighederne for at markedsføre sig dér. Bogen beskriver på hvilke væsentlige punkter...... marketing på Facebook adskiller sig fra traditionel marketing, og gennemgår trin for trin de fundamentale ting, som man skal vide for, at virksomheden kan agere med den tilsigtede effekt i et socialt netværk som Facebook. Og eftersom 34 % af den danske befolkning i dag er hoppet med på Facebook vognen og...... har oprettet en profil på Facebook, er potentialet åbenlyst....

Stamping of Thin-Walled Structural Components with Magnesium Alloy AZ31 Sheets

International Nuclear Information System (INIS)

Chen, F.-K.; Chang, C.-K.

2005-01-01

In the present study, the stamping process for manufacturing cell phone cases with magnesium alloy AZ31 sheets was studied using both the experimental approach and the finite element analysis. In order to determine the proper forming temperature and set up a fracture criterion, tensile tests and forming limit tests were first conducted to obtain the mechanical behaviors of AZ31 sheets at various elevated temperatures. The mechanical properties of Z31 sheets obtained from the experiments were then adopted in the finite element analysis to investigate the effects of the process parameters on the formability of the stamping process of cell phone cases. The finite element simulation results revealed that both the fracture and wrinkle defects could not be eliminated at the same time by adjusting blank-holder force or blank size. A drawbead design was then performed using the finite element simulations to determine the size and the location of drawbead required to suppress the wrinkle defect. An optimum stamping process, including die geometry, forming temperature, and blank dimension, was then determined for manufacturing the cell phone cases. The finite element analysis was validated by the good agreement between the simulation results and the experimental data. It confirms that the cell phone cases can be produced with magnesium alloy AZ31 sheet by the stamping process at elevated temperatures

Histone variant H2A.Z antagonizes the positive effect of the transcriptional activator CPC1 to regulate catalase-3 expression under normal and oxidative stress conditions.

Science.gov (United States)

Dong, Qing; Wang, Yajun; Qi, Shaohua; Gai, Kexin; He, Qun; Wang, Ying

2018-05-05

In eukaryotes, deposition of the histone variant H2A.Z into nucleosomes through the chromatin remodeling complex, SWR1, is a crucial step in modulating gene transcription. Recently, H2A.Z has been shown to control the expression of responsive genes, but the underlying mechanism of how H2A.Z responds to physiological stimuli is not well understood. Here, we reveal that, in Neurospora crassa, H2A.Z is a negative regulator of catalase-3 gene, which is responsible for resistance to oxidative stress. H2A.Z represses cat-3 gene expression through direct incorporation at cat-3 locus in a SWR1 complex dependent pathway. Notably, loss of H2A.Z or SWR1 subunits leads to increased binding of a transcription factor, CPC1, at cat-3 locus. Additionally, introduction of plasmids containing gene encoding H2A.Z or SWR1 complex subunits into wild-type strains decreased CAT-3 expression, indicating that H2A.Z counteracts the positive effect of CPC1 to achieve low level cat-3 expression under non-inductive condition. Furthermore, upon oxidative stress, H2A.Z is rapidly evicted from cat-3 locus for the recruitment of CPC1, resulting in robust and full cat-3 gene expression in response to external stimuli. Collectively, this study strongly demonstrates that H2A.Z antagonizes the function of transcription factor to regulate responsive gene transcription under normal conditions and to poise for gene full activation under oxidative stress. Copyright © 2018. Published by Elsevier Inc.

Friction stir welded AM50 and AZ31 Mg alloys: Microstructural evolution and improved corrosion resistance

Energy Technology Data Exchange (ETDEWEB)

Templeman, Yael [Department of Materials Engineering, Ben Gurion University of the Negev, PO Box 653, Beer Sheva 84105 (Israel); Ben Hamu, Guy [Department of Mechanical Engineering, Sami Shamoon College of Engineering, Ashdod 77245 (Israel); Meshi, Louisa, E-mail: Louisa@bgu.ac.il [Department of Materials Engineering, Ben Gurion University of the Negev, PO Box 653, Beer Sheva 84105 (Israel)

2017-04-15

One of the major drawbacks of Mg alloys is poor weldability, caused by porosity formation during conventional fusion welding processes. Friction Stir Welding (FSW) is promising technique in this context since it is a solid state technique. Contradicting results were published in the literature regarding the FSWed Mg alloys joint's properties. Current research was performed in order to investigate the microstructure and corrosion properties of FSWed Mg alloys, studying representatives of two commercial families: wrought AZ31-H24 and die cast AM50. It was found that in both alloys recrystallization occurred during the FSW. In AM50 the mechanism of the recrystallization was continuous, manifested by dislocation rearrangement into sub grain boundaries. In AZ31 discontinuous recrystallization had occurred through grain boundaries migration - twins rotated with respect to the matrix, turning into low angle grain boundaries. Corrosion resistance has improved during the FSW in both alloys to different extents. In the AM50 alloy, the nugget exhibited significantly higher surface potential than the base metal mainly due to the higher Al concentration in the matrix of the nugget, resulting from the dissolution of Al-enrichment and β-Mg{sub 17}Al{sub 12} phase. In the AZ31 alloy, no change in Al concentration had occurred, and the surface potential measured in the nugget was only slightly higher than in the base metal. These results underline the appropriateness of the FSW for Mg alloys since during the conventional welding deterioration of the corrosion resistance occurs. - Highlights: • Following FSW, AZ31-H24 experienced discontinuous recrystallization. • In AZ31 grain boundaries migration occurred, thus twins rotated. • In die cast AM50 continuous recrystallization occurred during the FSW. • In AM50 - dislocations rearranged into sub grain boundaries. • Corrosion resistance has improved during the FSW in both alloys to different extent.

Friction stir welded AM50 and AZ31 Mg alloys: Microstructural evolution and improved corrosion resistance

International Nuclear Information System (INIS)

Templeman, Yael; Ben Hamu, Guy; Meshi, Louisa

2017-01-01

One of the major drawbacks of Mg alloys is poor weldability, caused by porosity formation during conventional fusion welding processes. Friction Stir Welding (FSW) is promising technique in this context since it is a solid state technique. Contradicting results were published in the literature regarding the FSWed Mg alloys joint's properties. Current research was performed in order to investigate the microstructure and corrosion properties of FSWed Mg alloys, studying representatives of two commercial families: wrought AZ31-H24 and die cast AM50. It was found that in both alloys recrystallization occurred during the FSW. In AM50 the mechanism of the recrystallization was continuous, manifested by dislocation rearrangement into sub grain boundaries. In AZ31 discontinuous recrystallization had occurred through grain boundaries migration - twins rotated with respect to the matrix, turning into low angle grain boundaries. Corrosion resistance has improved during the FSW in both alloys to different extents. In the AM50 alloy, the nugget exhibited significantly higher surface potential than the base metal mainly due to the higher Al concentration in the matrix of the nugget, resulting from the dissolution of Al-enrichment and β-Mg 17 Al 12 phase. In the AZ31 alloy, no change in Al concentration had occurred, and the surface potential measured in the nugget was only slightly higher than in the base metal. These results underline the appropriateness of the FSW for Mg alloys since during the conventional welding deterioration of the corrosion resistance occurs. - Highlights: • Following FSW, AZ31-H24 experienced discontinuous recrystallization. • In AZ31 grain boundaries migration occurred, thus twins rotated. • In die cast AM50 continuous recrystallization occurred during the FSW. • In AM50 - dislocations rearranged into sub grain boundaries. • Corrosion resistance has improved during the FSW in both alloys to different extent.

Tank 241-AZ-101 steam bumping and settling Process Test report

International Nuclear Information System (INIS)

Winkler, C.M.

1995-01-01

This report summarizes the process test in which the airlift circulators in Tank 241-AZ-101 were shutdown. The test was successful, in that no extreme temperature excursions occurred. Only general data was obtianed through the use of a gamma energy probe

Phoenix Miracles in Emerging Markets: Recovering without Credit from Systemic Financial Crises

OpenAIRE

Guillermo A. Calvo; Alejandro Izquierdo; Ernesto Talvi

2006-01-01

Using a sample of emerging markets that are integrated into global bond markets, we analyze the collapse and recovery phase of output collapses that coincide with systemic sudden stops, defined as periods of skyrocketing aggregate bond spreads and large capital flow reversals. Our findings indicate the presence of a very similar pattern across different episodes: output recovers with virtually no recovery in either domestic or foreign credit, a phenomenon that we call Phoenix Miracle, where o...

Phoenix flagships: Conservation values and guanaco reintroduction in an anthropogenic landscape.

Science.gov (United States)

Lindon, Adrien; Root-Bernstein, Meredith

2015-09-01

Multiple forms of valuation contribute to public acceptance of conservation projects. Here, we consider how esthetic, intrinsic, and utilitarian values contribute to public attitudes toward a proposed reintroduction of guanaco (Lama guanicoe) in a silvopastoral system of central Chile. The nexus among landscape perceptions and valuations, support for reintroductions, and management of anthropogenic habitats is of increasing interest due to the proliferation of conservation approaches combining some or all of these elements, including rewilding and reconciliation ecology, for example. We assessed attitudes and values through an online questionnaire for residents of Santiago, Chile, using multiple methods including photo-montages and Likert scale assessments of value-based statements. We also combined the questionnaire approach with key informant interviews. We find strong support for the reintroduction of guanacos into the Chilean silvopastoral system ('espinal') in terms of esthetic and intrinsic values but less in terms of utilitarian values. Respondents preferred a scenario of espinal with guanacos and expressed interest in visiting it, as well as support for the reintroduction project on the basis that guanacos are native to central Chile. We suggest that reintroduced guanacos could serve as a 'phoenix flagship species' for espinal conservation, that is, a flagship species that has gone regionally extinct and is known but not associated with the region in the cultural memory. We consider how the lack of local cultural identity can both help and weaken phoenix flagships, which we expect to become more common.

Corrosion behavior of biodegradable material AZ31 coated with beeswax-colophony resin

Science.gov (United States)

Gumelar, Muhammad Dikdik; Putri, Nur Ajrina; Anggaravidya, Mahendra; Anawati, Anawati

2018-05-01

Magnesium (Mg) and its alloys are potential candidates for biodegradable implant materials owing to their ability to degrade spontaneously in a physiological environment. However, the degradation rate is still considered too fast in human body solution. A coating is typically applied to slowdown corrosion rate of Mg alloys. In this work, an organic coating of mixture beeswax-colophony with ratios of 40-60, 50-50, and 60-40 in wt% was synthesized and applied on commercial magnesium alloyAZ31. The coated specimens were then characterized with SEM and XRF. The corrosion behavior of the coated specimens was evaluated by immersion test in 0.9 wt% NaCl solution at 37°C for 14 days. The results indicated that the coating material improved the corrosion resistance of the AZ31 alloy.

Phoenix dactylifera L. spathe essential oil: Chemical composition and repellent activity against the yellow fever mosquito

Science.gov (United States)

Date palm, Phoenix dactylifera L. (Arecaceae), grows commonly in the Arabian Peninsula and is traditionally used to treat various diseases. The aim of the present study was to identify chemical composition of the essential oil and to investigate the repellent activity. The essential oil of P. dacty...

Effect of magnesium hydride on the corrosion behavior of an AZ91 magnesium alloy in sodium chloride solution

International Nuclear Information System (INIS)

Chen Jian; Dong Junhua; Wang Jianqiu; Han Enhou; Ke Wei

2008-01-01

The effect of magnesium hydride on the corrosion behavior of an as-cast AZ91 alloy in 3.5 wt.% NaCl solution was investigated using gas collection method and potentiostatic test. The Pourbaix diagram of Mg-H 2 O system was built using thermodynamic calculation. It was possible that magnesium hydride could form in the whole pH range in theory. The experimental results showed that at cathodic region, magnesium hydride formed on surface, which was the controlling process for the corrosion behavior of AZ91 alloy; at anodic region and free corrosion potential, magnesium hydride model and partially protective film model, monovalent magnesium ion model and particle undermining model were responsible for the corrosion process of AZ91 alloy

Urban effects on regional climate: a case study in the Phoenix and Tucson ‘sun’ corridor

Science.gov (United States)

Zhao Yang,; Francina Dominguez,; Hoshin Gupta,; Xubin Zeng,; Norman, Laura M.

2016-01-01

Land use and land cover change (LULCC) due to urban expansion alter the surface albedo, heat capacity, and thermal conductivity of the surface. Consequently, the energy balance in urban regions is different from that of natural surfaces. To evaluate the changes in regional climate that could arise due to projected urbanization in the Phoenix-Tucson corridor, Arizona, we applied the coupled WRF-NOAH-UCM (which includes a detailed urban radiation scheme) to this region. Land cover changes were represented using land cover data for 2005 and projections to 2050, and historical North American Regional Reanalysis (NARR) data were used to specify the lateral boundary conditions. Results suggest that temperature changes will be well defined, reflecting the urban heat island (UHI) effect within areas experiencing LULCC. Changes in precipitation are less robust, but seem to indicate reductions in precipitation over the mountainous regions northeast of Phoenix and decreased evening precipitation over the newly-urbanized area.

Review of Considerations, Management, and Treatment of Medical Emergencies During Commercial Flight

Science.gov (United States)

2017-04-01

MedAire, from Banner Good Samaritan Hospital, Phoenix, AZ; Stat-MD, from the University of Pittsburgh Hospital, Pittsburgh, PA; and The First Call, from...COMMON MEDICAL EMERGENCIES IN FLIGHT: THE FLIGHT ENVIRONMENT Air travel has become quite the luxurious mode of transportation in the past few...pH, known as the Bohr effect [12]. As the hydrogen ion concentration is increased, indicated by a decrease in pH, the oxyhemoglobin dissociation curve

Mechanical behaviour of biodegradable AZ31 magnesium alloy after long term in vitro degradation.

Science.gov (United States)

Adekanmbi, Isaiah; Mosher, Christopher Z; Lu, Helen H; Riehle, Mathis; Kubba, Haytham; Tanner, K Elizabeth

2017-08-01

Biodegradable magnesium alloys including AZ31 are exciting candidates for temporary implants as they eliminate the requirement for surgical removal, yet have higher mechanical properties than degradable polymers. However, the very long term mechanical properties and degradation of these alloys have not been fully characterized. The tensile, bending and corrosion behaviour of biodegradable AZ31 Mg alloy specimens have been investigated for up to 9months in vitro in phosphate buffered saline (PBS). Small AZ31 Mg specimens showed a significant drop in bend yield strength and modulus after 3months in vitro degradation and an average mass loss of 6.1%. Larger dumbbell specimens showed significant drops in tensile strength from 251.96±3.53MPa to 73.5±20.2MPa and to 6.43±0.9MPa and in modulus from 47.8±5.6GPa to 25.01±3.4GPa and 2.36±0.89GPa after 3 and 9months respectively. These reductions were accompanied by an average mass loss of 18.3% in 9months. Degradation rate for the small and large specimens followed similar profiles with immersion time, with peak degradation rates of 0.1747gm -2 h - 1 and 0.0881gm -2 h - 1 , and average rates of 0.1038gm -2 h - 1 and 0.0397gm -2 h - 1 respectively. SEM fractography and polished specimen cross-sections revealed corrosion pits, cracks and corrosion induced defects. These data indicate the potential of AZ31 Mg for use in implants that require medium term degradation with load bearing mechanical properties. Copyright © 2017 Elsevier B.V. All rights reserved.

Influence of boron addition on the grain refinement and mechanical properties of AZ91 Mg alloy

International Nuclear Information System (INIS)

Suresh, M.; Srinivasan, A.; Ravi, K.R.; Pillai, U.T.S.; Pai, B.C.

2009-01-01

This article reports the effect of boron addition on the grain refinement efficiency and mechanical properties of AZ91 magnesium alloy. The results show that the addition of boron in the form of Al-4B master alloy, significantly refines the grain size of AZ91 alloy. This refinement is due to the presence of AlB 2 particles, which act as potential nucleants for Mg grains. Improved mechanical properties are obtained with the addition of boron due to the finer grains.

Structural evaluation of thermocouple probes for 241-AZ-101 waste tank

International Nuclear Information System (INIS)

Kanjilal, S.K.

1994-01-01

This document reports on the structural analysis of the thermocouple probe to be installed in 241-AZ-101 waste tank. The thermocouple probe is analyzed for normal pump mixing operation and potential earthquake induced loads required by the Hanford Site Design Criteria SDC-4.1

Structural evaluation of thermocouple probes for 241-AZ-101 waste tank

Energy Technology Data Exchange (ETDEWEB)

Kanjilal, S.K.

1994-12-06

This document reports on the structural analysis of the thermocouple probe to be installed in 241-AZ-101 waste tank. The thermocouple probe is analyzed for normal pump mixing operation and potential earthquake induced loads required by the Hanford Site Design Criteria SDC-4.1.

Conformal, planarizing and bridging AZ5214-E layers deposited by a 'draping' technique on non-planar III V substrates

Science.gov (United States)

Eliás, P.; Strichovanec, P.; Kostic, I.; Novák, J.

2006-12-01

A draping technique was tested for the deposition of positive-tone AZ5214-E photo-resist layers on non-planar (1 0 0)-oriented III-V substrates, which had a variety of three-dimensional (3D) topographies micromachined in them that consisted, e.g., of mesa ridges confined to side facets with variable tilt, inverted pyramidal holes and stubs confined to perpendicular side facets. All objects were sharp-edged. In each draping experiment, an AZ5214-E sheet was (1) formed floating on the water surface, (2) lowered onto a non-planar substrate and (3) draped over it during drying to form either self-sustained, or conformal, or planarizing layers over the non-planar substrates. The draping process is based on the depression of the glass transition temperature Tg of AZ5214-E material induced by penetrant water molecules that interact with AZ5214-E. During the process, the molecules are initially trapped under an AZ5214-E sheet and then transported out through the sheet via permeation. The water-AZ5214-E interaction modifies the stiffness κ of the sheet. The magnitude of the effect depends on temperature T and on partial water vapour pressure difference p(T, P, κ): the net effect is that Tg = f(C(T, P), p(T, P, κ)) is lowered as the concentration C of water increases with T and p, where P is the permeability of the sheet. The interaction depressed the Tg of the sheets as low as or lower than 53 °C for 6 µm thick sheets. At room temperature T Tg, the sheet becomes rubbery and mouldable by adhesion and capillary forces. As a result, it can either contour or planarize the topography depending on its geometry and thickness of the sheet.

Structure of the AZ91 alloy pressure castings fabricated of home scrap containing charge

Directory of Open Access Journals (Sweden)

Z. Konopka

2011-04-01

Full Text Available The influence of the AZ91 alloy home scrap addition to the metal charge on both the structure and the selected mechanical propertiesof pressure castings was examined in this article. Two heats were made using different components, the first with only pure AZ91 alloyingots in the charge, and the second containing 30 wt % of home scrap. The hot chamber 3 MN machine was used for casting. Thestructures of the castings and their Brinell hardness were examined for both cases. A strong refinement of crystals was observed in castings made with the contribution of the recycled material. Any significant differences in castings hardness were not observed.

Influence of Zeolite Coating on the Corrosion Resistance of AZ91D Magnesium Alloy.

Science.gov (United States)

Banerjee, P Chakraborty; Woo, Ren Ping; Grayson, Sam Matthew; Majumder, Amrita; Raman, R K Singh

2014-08-22

The protective performance of zeolite coating on AZ91D magnesium alloy was evaluated using potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS) in 0.1 M sodium chloride solution (NaCl). Electrical equivalent circuit (EEC) was developed based upon hypothetical corrosion mechanisms and simulated to correspond to the experimental data. The morphology and the chemical nature of the coating were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. Post corrosion morphologies of the zeolite coated and the uncoated AZ91D alloy were investigated using SEM. The corrosion resistance of the zeolite coated specimen was at least one order of magnitude higher than the uncoated specimen.

Desert heat island study in winter by mobile transect and remote sensing techniques

Science.gov (United States)

Sun, Chen-Yi; Brazel, Anthony J.; Chow, Winston T. L.; Hedquist, Brent C.; Prashad, Lela

2009-10-01

A familiar problem in urban environments is the urban heat island (UHI), which potentially increases air conditioning demands, raise pollution levels, and could modify precipitation patterns. The magnitude and pattern of UHI effects have been major concerns of a lot of urban environment studies. Typically, research on UHI magnitudes in arid regions (such as Phoenix, AZ, USA) focuses on summer. UHI magnitudes in Phoenix (more than three million population) attain values in excess of 5°C. This study investigated the early winter period—a time when summer potential evapotranspiration >250 mm has diminished to 8.0°C, comparable to summertime UHI conditions. Through analysis of the Oke (1998) weather factor ΦW, it was determined thermally induced nighttime cool drainage winds could account for inflating the UHI magnitude in winter.

Corrosion characterization of micro-arc oxidization composite electrophoretic coating on AZ31B magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Wang, Congjie [School of Materials Science and Engineering, Xi’an University of Technology, Xi’an 710048 (China); Jiang, Bailing [School of Materials Science and Engineering, Nanjing Tech University, Nanjing 211816 (China); Liu, Ming [General Motors China Science Lab, Shanghai 201206 (China); Ge, Yanfeng [School of Materials Science and Engineering, Xi’an University of Technology, Xi’an 710048 (China)

2015-02-05

Highlights: • A new protective composite coatings were prepared on AZ31B Mg alloy. • The E-coat locked into MAO coat by discharge channels forming a smoother and compact surface without defects. • Comparing with MAO coat, the MAOE composite coat could provide an excellent barrier for bare Mg against corrosion attack. - Abstract: A two layer composite coating system was applied on the surface of AZ31B magnesium alloy by Micro-arc Oxidation (MAO) plus electrophoretic coat (E-coat) technique. The Mg sample coated with MAO plus E-coat (MAOE) was compared with bare Mg and Mg sample coated by MAO only. The surface microstructure and cross section of bare and coated Mg before and after corrosion were examined by Scanning Electron Microscopy (SEM). The corrosion performance of bare and coated Mg was evaluated using electrochemical measurement and hydrogen evolution test. The results indicated that the corrosion resistance of AZ31B Mg alloy was significantly improved by MAOE composite coating. The corrosion mechanism of bare and coated Mg is discussed.

Influence of heat treatment on the machinability and corrosion behavior of AZ91 Mg alloy

Directory of Open Access Journals (Sweden)

Swetha Chowdary V

2018-03-01

Full Text Available In the present study, AZ91 Mg alloy was heat treated at 410 °C for 6, 12 and 24 h to investigate the influence of heat treatment on machinability and corrosion behavior. The effect of soaking time on the amount and distribution of Mg17Al12 (β – phase was analyzed under the optical microscope. Microhardness measurements demonstrated the increased hardness with increased heat treatment soaking time, which can be attributed to the solid solution strengthening. The influence of super saturated α-grains on reducing the cutting force (Fz with respect to increased cutting speed was observed as prominent. The corrosion behavior of the heat treated specimens was studied by conducting electrochemical tests. Surprisingly, corrosion rate of heat treated samples was observed as increased compared with the base material. From the results, it is evident that the machinability of AZ91 Mg alloy can be improved by producing super saturated α-grains through heat treatment but at the cost of losing corrosion resistance. Keywords: AZ91 Mg alloy, Solid solution, Turning, Corrosion, Machinability

AZ-2000-IECW and StaMet Black Kapton Options for Solar Probe Plus MAG Sensor MLI Kevlar/Polyimide Shells

Science.gov (United States)

Choi, Michael K.

2017-01-01

AZ-2000-IECW white paint and StaMet black Kapton have been evaluated for the Kevlar/polyimide shells that enclose the Solar Probe Plus Magnetometer (MAG) sensors and multilayer insulation. Flight qualification testing on AZ-2000-IECW painted Kevlar/polyimide laminate was completed at Goddard Space Flight Center. This paint potentially meets all the requirements. However, it has no flight heritage. StaMet is hotter in the sun, and is specular. The results of the MAG thermal balance test show StaMet meets the thermal requirement and heater power budget. The mission prefers to fly StaMet after evaluating the risks of AZ-2000-IECW flaking and glint from StaMet to the Star Trackers.

Analysis of Phoenix Anomalies and IV & V Findings Applied to the GRAIL Mission

Science.gov (United States)

Larson, Steve

2012-01-01

NASA IV&V was established in 1993 to improve safety and cost-effectiveness of mission critical software. Since its inception the tools and strategies employed by IV&V have evolved. This paper examines how lessons learned from the Phoenix project were developed and applied to the GRAIL project. Shortly after selection, the GRAIL project initiated a review of the issues documented by IV&V for Phoenix. The motivation was twofold: the learn as much as possible about the types of issues that arose from the flight software product line slated for use on GRAIL, and to identify opportunities for improving the effectiveness of IV&V on GRAIL. The IV&V Facility provided a database dump containing 893 issues. These were categorized into 16 bins, and then analyzed according to whether the project responded by changing the affected artifacts or using as-is. The results of this analysis were compared to a similar assessment of post-launch anomalies documented by the project. Results of the analysis were discussed with the IV&V team assigned to GRAIL. These discussions led to changes in the way both the project and IV&V approached the IV&V task, and improved the efficiency of the activity.

Test-retest reliability of [{sup 11}C]AZ10419369 binding to 5-HT{sub 1B} receptors in human brain

Energy Technology Data Exchange (ETDEWEB)

Nord, Magdalena; Finnema, Sjoerd J.; Schain, Martin; Halldin, Christer; Farde, Lars [Karolinska Institutet, Center for Psychiatric Research, R5:00, Karolinska University Hospital, Department of Clinical Neuroscience, Stockholm (Sweden)

2014-02-15

[{sup 11}C]AZ10419369 is a recently developed 5-HT{sub 1B} receptor radioligand that is sensitive to changes in endogenous serotonin concentrations in the primate brain. Thus, [{sup 11}C] AZ10419369 may serve as a useful tool in clinical studies of the pathophysiology and pharmacological treatment of diseases related to the serotonin system, such as depression and anxiety disorders. The aim of this study was to evaluate the test-retest reliability of [{sup 11}C]AZ10419369. Eight men were examined with PET and [{sup 11}C] AZ10419369 twice on the same day. The binding potentials (BP{sub ND}) of [{sup 11}C]AZ10419369 in selected serotonergic projection areas and in the raphe nuclei (RN) were determined using the simplified reference tissue model, and for comparison also using a wavelet-aided parametric imaging approach. The BP{sub ND} values obtained from the first and second PET scans were compared by means of descriptive statistics, difference, absolute variability and intraclass correlation coefficient. Similar BP{sub ND} values were obtained with the two methods. The absolute mean differences in BP{sub ND} between PET 1 and PET 2 were less than 3 % in all serotonergic projection regions. Absolute variabilities were low in cortical regions (5 - 7 %), low to moderate (7 - 14 %) in subcortical regions, but higher (20 %) in the RN. The BP{sub ND} of [{sup 11}C]AZ10419369 is highly reproducible in cortical regions and satisfactory in subcortical projection areas. The variability in the RN is higher. Thus larger sample sizes or larger divergences are required to assess a potential difference between subjects or between experimental conditions in this region. (orig.)

Nano grained AZ31 alloy achieved by equal channel angular rolling process

International Nuclear Information System (INIS)

Hassani, F.Z.; Ketabchi, M.

2011-01-01

Equal channel angular rolling (ECAR) is a severe plastic deformation process which is carried out on large, thin sheets. The grain size could be significantly decreased by this process. The main purpose of this study is to investigate the possibility of grain refinement of AZ31 magnesium alloy sheet by this process to nanometer. The effect of the number of ECAR passes on texture evolution of AZ31 magnesium alloy was investigated. ECAR temperature was controlled to maximize the grain refinement efficiency along with preventing cracking. The initial microstructure of as-received AZ31 sheet showed an average grain size of about 21 μm. The amount of grain refinement increased with increasing the pass number. After 10 passes of the process, significant grain refinement occurred and the field emission scanning electron microscopic (FESEM) micrographs showed that the size of grains were decreased significantly to about 14-70 nm. These grains were formed at the grain boundaries and inside some of the previous larger micrometer grains. Observation of optical microstructures and X-ray diffraction patterns (XRD) showed the formation of twins after ECAR process. Micro-hardness of material was studied at room temperature. There was a continuous enhancement of hardness by increasing the pass number of ECAR process. At the 8th pass, hardness values increased by 53%. At final passes hardness reduced slightly, which was attributed to saturation of strain in high number of passes.

Diffusion and solubility of Au implanted into the AZ1350 photoresist

International Nuclear Information System (INIS)

Soares, M.R.F.; Kaschny, J.R.A.; Santos, J.H.R. dos; Amaral, L.; Behar, M.; Fink, D.

2000-01-01

In the present paper we report diffusion and solubility results for Au into the photoresist AZ1350. Au was implanted into AZ1350 films at very low energy (E=20 keV) and fluences (PHI=10 12 and 5x10 12 Au/cm 2 ). In this way the radiation damage introduced by the implantation process was minimized and cluster formation was avoided. Annealing was performed in the 150-300 deg. C temperature range and the as implanted and thermal treated samples were analyzed using the Rutherford backscattering (RBS) technique. For the lowest implantation fluence the results have shown a regular atomic diffusion process characterized by an activation energy of E a =640 meV. Instead, for PHI=5x10 12 Au/cm 2 the diffusional mechanism has revealed the effects of the radiation damage. In addition solubility measurements indicate that the solubility limit at 250 deg. C is of the order 0.3 at.%

Live from Space Station Learning Technologies Project

Science.gov (United States)

2001-01-01

This is the Final Report for the Live From Space Station (LFSS) project under the Learning Technologies Project FY 2001 of the MSFC Education Programs Department. AZ Technology, Inc. (AZTek) has developed and implemented science education software tools to support tasks under the LTP program. Initial audience consisted of 26 TreK in the Classroom schools and thousands of museum visitors to the International Space Station: The Earth Tour exhibit sponsored by Discovery Place museum.

Effects of organic acid pickling on the corrosion resistance of magnesium alloy AZ31 sheet

DEFF Research Database (Denmark)

Nwaogu, Ugochukwu Chibuzoh; Blawert, C.; Scharnagl, N.

2010-01-01

mu m of the contaminated surface was required to reach corrosion rates less than 1 mm/year in salt spray condition. Among the three organic acids examined, acetic acid is the best choice. Oxalic acid can be an alternative while citric acid is not suitable for cleaning AZ31 sheet, because......Organic acids were used to clean AZ31 magnesium alloy sheet and the effect of the cleaning processes on the surface condition and corrosion performance of the alloy was investigated. Organic acid cleanings reduced the surface impurities and enhanced the corrosion resistance. Removal of at least 4...

Loss of mechanical properties in vivo and bone-implant interface strength of AZ31B magnesium alloy screws with Si-containing coating.

Science.gov (United States)

Tan, Lili; Wang, Qiang; Lin, Xiao; Wan, Peng; Zhang, Guangdao; Zhang, Qiang; Yang, Ke

2014-05-01

In this study the loss of mechanical properties and the interface strength of coated AZ31B magnesium alloy (a magnesium-aluminum alloy) screws with surrounding host tissues were investigated and compared with non-coated AZ31B, degradable polymer and biostable titanium alloy screws in a rabbit animal model after 1, 4, 12 and 21weeks of implantation. The interface strength was evaluated in terms of the extraction torque required to back out the screws. The loss of mechanical properties over time was indicated by one-point bending load loss of the screws after these were extracted at different times. AZ31B samples with a silicon-containing coating had a decreased degradation rate and improved biological properties. The extraction torque of Ti6Al4V, poly-l-lactide (PLLA) and coated AZ31B increased significantly from 1week to 4weeks post-implantation, indicating a rapid osteosynthesis process over 3weeks. The extraction torque of coated AZ31B increased with implantation time, and was higher than that of PLLA after 4weeks of implantation, equalling that of Ti6Al4V at 12weeks and was higher at 21weeks. The bending loads of non-coated AZ31B and PLLA screws degraded sharply after implantation, and that of coated AZ31B degraded more slowly. The biodegradation mechanism, the coating to control the degradation rate and the bioactivity of magnesium alloys influencing the mechanical properties loss over time and bone-implant interface strength are discussed in this study and it is concluded that a suitable degradation rate will result in an improvement in the mechanical performance of magnesium alloys, making them more suitable for clinical application. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Effect of Mucin and Bicarbonate Ion on Corrosion Behavior of AZ31 Magnesium Alloy for Airway Stents.

Science.gov (United States)

Jang, Yongseok; Owuor, Daniel; Waterman, Jenora T; White, Leon; Collins, Boyce; Sankar, Jagannathan; Gilbert, Thomas W; Yun, Yeoheung

2014-08-15

The biodegradable ability of magnesium alloys is an attractive feature for tracheal stents since they can be absorbed by the body through gradual degradation after healing of the airway structure, which can reduce the risk of inflammation caused by long-term implantation and prevent the repetitive surgery for removal of existing stent. In this study, the effects of bicarbonate ion (HCO₃ - ) and mucin in Gamble's solution on the corrosion behavior of AZ31 magnesium alloy were investigated, using immersion and electrochemical tests to systematically identify the biodegradation kinetics of magnesium alloy under in vitro environment, mimicking the epithelial mucus surfaces in a trachea for development of biodegradable airway stents. Analysis of corrosion products after immersion test was performed using scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD). Electrochemical impedance spectroscopy (EIS) was used to identify the effects of bicarbonate ions and mucin on the corrosion behavior of AZ31 magnesium alloys with the temporal change of corrosion resistance. The results show that the increase of the bicarbonate ions in Gamble's solution accelerates the dissolution of AZ31 magnesium alloy, while the addition of mucin retards the corrosion. The experimental data in this work is intended to be used as foundational knowledge to predict the corrosion behavior of AZ31 magnesium alloy in the airway environment while providing degradation information for future in vivo studies.

Influence of Zeolite Coating on the Corrosion Resistance of AZ91D Magnesium Alloy

Directory of Open Access Journals (Sweden)

P. Chakraborty Banerjee

2014-08-01

Full Text Available The protective performance of zeolite coating on AZ91D magnesium alloy was evaluated using potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS in 0.1 M sodium chloride solution (NaCl. Electrical equivalent circuit (EEC was developed based upon hypothetical corrosion mechanisms and simulated to correspond to the experimental data. The morphology and the chemical nature of the coating were characterized by scanning electron microscopy (SEM and X-ray diffraction (XRD analysis. Post corrosion morphologies of the zeolite coated and the uncoated AZ91D alloy were investigated using SEM. The corrosion resistance of the zeolite coated specimen was at least one order of magnitude higher than the uncoated specimen.

Cambio en azúcares fermentables en la remolacha azucarera almacenada en atmósferas aerobia y anaerobia para la producción de etanol

Directory of Open Access Journals (Sweden)

Juan Manuel Vargas Ramírez

2014-06-01

Full Text Available Los métodos de almacenamiento de largo plazo son necesarios para preservar los azúcares fermentables en la remolacha y permitir el funcionamiento exitoso a lo largo del año en las plantas procesadoras para la obtención de etanol. Se estudió el almacenamiento anaeróbico de la remolacha azucarera como una alternativa al almacenamiento convencional en pilas a la intemperie utilizado actualmente en fábricas de azúcar de remolacha. Los resultados experimentales indican una pérdida de <15% en el total de los azúcares fermentables en la remolacha azucarera almacenada anaeróbicamente durante 14 semanas a 4 °C. Después de 14 semanas de almacenamiento, 99 ± 4% de los azúcares fermentables iniciales fueron preservados en la remolacha almacenada en condiciones aeróbicas a 4 °C. El almacenamiento aeróbico y anaeróbico de remolacha azucarera a 25 ° C conserva 82 ± 9 y 48 ± 11% del contenido de azúcar fermentable, respectivamente. Los azúcares fermentables y etanol en exudados contribuyeron insignificantemente (<3% para el rendimiento del etanol global de remolacha azucarera después del almacenamiento.

Magnetic and optical properties of airborne dust and settling rates of dust at the Phoenix landing site

DEFF Research Database (Denmark)

Drube...[], Line; Leer, Kristoffer; Madsen, Morten Bo

2010-01-01

The Magnetic Properties Experiment (referred to as iSweep or Caltarget) onboard the Phoenix lander was executed in the arctic region of Mars during the mission's 152 sols lifetime. The iSweep experiment involved periodic multispectral imaging of a series of permanent ring magnets. It was designed...

A Study on Compressive Anisotropy and Nonassociated Flow Plasticity of the AZ31 Magnesium Alloy in Hot Rolling

Directory of Open Access Journals (Sweden)

Guoqiang Wang

2014-01-01

Full Text Available Effect of anisotropy in compression is studied on hot rolling of AZ31 magnesium alloy with a three-dimensional constitutive model based on the quadratic Hill48 yield criterion and nonassociated flow rule (non-AFR. The constitutive model is characterized by compressive tests of AZ31 billets since plastic deformations of materials are mostly caused by compression during rolling processes. The characterized plasticity model is implemented into ABAQUS/Explicit as a user-defined material subroutine (VUMAT based on semi-implicit backward Euler's method. The subroutine is employed to simulate square-bar rolling processes. The simulation results are compared with rolled specimens and those predicted by the von Mises and the Hill48 yield function under AFR. Moreover, strip rolling is also simulated for AZ31 with the Hill48 yield function under non-AFR. The strip rolling simulation demonstrates that the lateral spread generated by the non-AFR model is in good agreement with experimental data. These comparisons between simulation and experiments validate that the proposed Hill48 yield function under non-AFR provides satisfactory description of plastic deformation behavior in hot rolling for AZ31 alloys in case that the anisotropic parameters in the Hill48 yield function and the non-associated flow rule are calibrated by the compressive experimental results.

Precipitation behavior and effect of new precipitated β phase in AZ80 magnesium alloy

Institute of Scientific and Technical Information of China (English)

TANG Wei; HAN En-hou; XU Yong-bo; LIU Lu

2006-01-01

Granular precipitate that was a new kind of β-Mg17Al12 phase found in aged AZ80 wrought Mg alloy at all aging temperature was studied. The structure and precipitation behavior of this granular β-Mg17Al12 precipitate were studied by environmental scanning electron microscopy (ESEM) and transmission electron microscopy (TEM). The effect of the granular precipitate on mechanical properties of AZ80 alloy was also studied. The new precipitate that was granular and nucleated both on grain boundaries (GBs) and twin boundaries, has the same crystal structure and lattice parameter as those of the continuous or discontinuous precipitated β-Mg17Al12. And the nucleation and growth of the granular precipitate are faster than those of the other two precipitates at higher temperatures (above 583 K), but are suppressed at lower temperatures (below 423 K). At lower temperatures, the discontinuous β-Mg17Al12 precipitates firstly and the granular β-Mg17Al12 precipitates after aged more than 40 h. The crack is easily nucleated on the phase boundaries of granular phase and matrix because of the weak binding force. As a result, the strength and ductility of AZ80 Mg alloy are decreased by the granular β-Mg17Al12 precipitate.

Mixer pump test plan for double shell tank AZ-101

International Nuclear Information System (INIS)

STAEHR, T.W.

1999-01-01

Mixer pump systems have been chosen as the method for retrieval of tank wastes contained in double shell tanks at Hanford. This document describes the plan for testing and demonstrating the ability of two 300 hp mixer pumps to mobilize waste in tank AZ-101. The mixer pumps, equipment and instrumentation to monitor the test were installed by Project W-151

In vitro corrosion of pure magnesium and AZ91 alloy?the influence of thin electrolyte layer thickness

OpenAIRE

Zeng, Rong-Chang; Qi, Wei-Chen; Zhang, Fen; Li, Shuo-Qi

2016-01-01

In vivo degradation predication faces a huge challenge via in vitro corrosion test due to the difficulty for mimicking the complicated microenvironment with various influencing factors. A thin electrolyte layer (TEL) cell for in vitro corrosion of pure magnesium and AZ91 alloy was presented to stimulate the in vivo corrosion in the micro-environment built by the interface of the implant and its neighboring tissue. The results demonstrated that the in vivo corrosion of pure Mg and the AZ91 all...

The U.S. Department of Energy Office of Indian Energy Policy and Programs Phoenix, Arizona, Roundtable Summary

Energy Technology Data Exchange (ETDEWEB)

none,

2011-04-05

The Phoenix, Arizona, Roundtable on Tribal Energy Policy convened at 8:30 a.m., Tuesday, April 5th, at the downtown Phoenix Hyatt. The meeting was hosted by the Department of Energy (DOE) Office of Indian Energy Policy and Programs (DOE Office of Indian Energy) and facilitated by the Udall Foundation’s U.S. Institute for Environmental Conflict Resolution (U.S. Institute). Approximately thirty-eight people attended the meeting, including representatives of ten different tribes, as well as representatives of the Colorado Indian Tribes, the All Indian Pueblo Council and the Inter-Tribal Council of Arizona. Interested state, federal, university, NGO and industry representatives also were present. A full list of attendees is at the end of this summary. DOE representatives were Tracey LeBeau, Directory of the DOE Office of Indian Energy, Pilar Thomas, Deputy Director-Policy of the DOE Office of Indian Energy, and David Conrad, Director of Tribal and Intergovernmental Affairs, DOE Office of Congressional and Intergovernmental Affairs.

Effect of interlayer configurations on joint formation in TLP bonding of Ti-6AI-4V to Mg-AZ31

International Nuclear Information System (INIS)

Atieh, A. M.; Khan, T. I.

2013-01-01

In this research work, the transient liquid phase (TLP) bonding process was utilized to fabricate joints using thin (20 micro m) nickel and copper foils placed between two bonding surfaces to help facilitate joint formation. Two joint configurations were investigated, first, Ti-6Al-4V/CuNi/Mg-AZ31 and second, Ti-6Al-4V/NiCu/Mg-AZ3L The effect of bonding time on microstructural developments across the joint and the changes in mechanical properties were studied as a function of bonding temperature and pressure. The bonded specimens were examined by metallographic analysis, scanning electron microscopy (SEM), and X-ray diffraction (XRD). In both cases, intermetallic phase of CuMg/sub 2/ and Mg/sub 3/AlNi/sub 2/ was observed inside the joint region. The results show that joint shear strengths for the Ti-6Al-4V/CuNi/Mg-AZ31 setup produce joints with shear strength of 57 MPa compared to 27MPa for joints made using the Ti-6Al-4V/NiCu/Mg-AZ31 layer arrangement. (author)

Effect of interlayer configurations on joint formation in TLP bonding of Ti-6Al-4V to Mg-AZ31

International Nuclear Information System (INIS)

Atieh, A M; Khan, T I

2014-01-01

In this research work, the transient liquid phase (TLP) bonding process was utilized to fabricate joints using thin (20μm) nickel and copper foils placed between two bonding surfaces to help facilitate joint formation. Two joint configurations were investigated, first, Ti-6Al-4V/CuNi/Mg-AZ31 and second, Ti-6Al-4V/NiCu/Mg-AZ3L The effect of bonding time on microstructural developments across the joint and the changes in mechanical properties were studied as a function of bonding temperature and pressure. The bonded specimens were examined by metallographic analysis, scanning electron microscopy (SEM), and X-ray diffraction (XRD). In both cases, intermetallic phase of CuMg 2 and Mg 3 AlNi 2 was observed inside the joint region. The results show that joint shear strengths for the Ti-6Al-4V/CuNi/Mg-AZ31 setup produce joints with shear strength of 57 MPa compared to 27MPa for joints made using the Ti-6Al-4V/NiCu/Mg-AZ31 layer arrangement

Comparative study between rib imaging of DR dual energy subtraction technology and chest imaging

International Nuclear Information System (INIS)

Yu Jianming; Lei Ziqiao; Kong Xiangchuang

2006-01-01

Objective: To investigate the application value of DR dual energy subtraction technology in rib lesions. Methods: 200 patients were performed with chest DR dual energy subtraction, comparing the rib imaging between DR of thorax and chest imaging using ROC analysis. Results: Among the total of 200 patients, there are 50 cases of rib calcification, 7 cases of rib destruction, 22 cases of rib fracture. The calcification, destruction and fracture were displayed respectively by ribs below diaphragm and rib markings. The analytic parameter of rib imaging of DR dual energy subtraction Az is 0.9367, while that of rib imaging of chest Az is 0.6830. Conclusion: DR dual energy subtraction technology is superior to chest imaging in the displaying of rib lesion and ribs below diaphragm. (authors)

Evolution of twinning in extruded AZ31 alloy with bimodal grain structure

Energy Technology Data Exchange (ETDEWEB)

Garcés, G., E-mail: ggarces@cenim.csic.es [Department of Physical Metallurgy, National Centre for Metallurgical Research CENIM-CSIC, Av. De Gregorio del Amo 8, 28040 Madrid (Spain); Oñorbe, E. [CIEMAT, Division of Structural Materials, Avenida Complutense, 40, 28040 Madrid (Spain); Gan, W. [German Engineering Materials Science Centre at MLZ, Helmholtz-Zentrum Geesthacht, Lichtebergstr. 1, D-85747 Garching (Germany); Máthis, K. [Department of Physics of Materials, Faculty of Mathematics and Physics, Charles University, KeKarlovu 5, 121 16 Praha 2 (Czech Republic); Tolnai, D. [Institute of Materials Research, Helmholtz-Zentrum Geesthacht, Max-Planck-Str. 1, 21502 Geesthacht (Germany); Horváth, K. [Department of Physics of Materials, Faculty of Mathematics and Physics, Charles University, KeKarlovu 5, 121 16 Praha 2 (Czech Republic); Pérez, P.; Adeva, P. [Department of Physical Metallurgy, National Centre for Metallurgical Research CENIM-CSIC, Av. De Gregorio del Amo 8, 28040 Madrid (Spain)

2017-04-15

Twinning in extruded AZ31 alloy with a bimodal grain structure is studied under compression along the extrusion direction. This study has combined in-situ measurements during the compression tests by Synchrotron Radiation Diffraction and Acoustic Emission techniques and the evaluation of the microstructure and texture in post-mortem compression samples deformed at different strains. The microstructure of the alloy is characterized by the coexistence of large areas of fine dynamic recrystallized grains and coarse non-recrystallized grains elongated along extrusion direction. Twinning occurs initially in large elongated grains before the macroscopic yield stress which is controlled by the twinning in equiaxed dynamically recrystallized grains. - Highlights: • The AZ31 extruded at low temperature exhibits a bimodal grains structure. • Twinning takes place before macroscopic yielding in coarse non-DRXed grains. • DRXed grains controls the beginning of plasticity in magnesium alloys with bimodal grain structure.

Wire Arc Additive Manufacturing of AZ31 Magnesium Alloy: Grain Refinement by Adjusting Pulse Frequency

Directory of Open Access Journals (Sweden)

Jing Guo

2016-10-01

Full Text Available Wire arc additive manufacturing (WAAM offers a potential approach to fabricate large-scale magnesium alloy components with low cost and high efficiency, although this topic is yet to be reported in literature. In this study, WAAM is preliminarily applied to fabricate AZ31 magnesium. Fully dense AZ31 magnesium alloy components are successfully obtained. Meanwhile, to refine grains and obtain good mechanical properties, the effects of pulse frequency (1, 2, 5, 10, 100, and 500 Hz on the macrostructure, microstructure and tensile properties are investigated. The results indicate that pulse frequency can result in the change of weld pool oscillations and cooling rate. This further leads to the change of the grain size, grain shape, as well as the tensile properties. Meanwhile, due to the resonance of the weld pool at 5 Hz and 10 Hz, the samples have poor geometry accuracy but contain finer equiaxed grains (21 μm and exhibit higher ultimate tensile strength (260 MPa and yield strength (102 MPa, which are similar to those of the forged AZ31 alloy. Moreover, the elongation of all samples is above 23%.

In vitro corrosion of pure magnesium and AZ91 alloy—the influence of thin electrolyte layer thickness

Science.gov (United States)

Zeng, Rong-Chang; Qi, Wei-Chen; Zhang, Fen; Li, Shuo-Qi

2016-01-01

In vivo degradation predication faces a huge challenge via in vitro corrosion test due to the difficulty for mimicking the complicated microenvironment with various influencing factors. A thin electrolyte layer (TEL) cell for in vitro corrosion of pure magnesium and AZ91 alloy was presented to stimulate the in vivo corrosion in the micro-environment built by the interface of the implant and its neighboring tissue. The results demonstrated that the in vivo corrosion of pure Mg and the AZ91 alloy was suppressed under TEL condition. The AZ91 alloy was more sensitive than pure Mg to the inhibition of corrosion under a TEL thickness of less than 200 µm. The TEL thickness limited the distribution of current, and thus localized corrosion was more preferred to occur under TEL condition than in bulk solution. The TEL cell might be an appropriate approach to simulating the in vivo degradation of magnesium and its alloys. PMID:26816655

Corrosion of AZ91D magnesium alloy with a chemical conversion coating and electroless nickel layer

International Nuclear Information System (INIS)

Huo Hongwei; Li Ying; Wang Fuhui

2004-01-01

A chemical conversion treatment and an electroless nickel plating were applied to AZ91D alloy to improve its corrosion resistance. By conversion treatment in alkaline stannate solution, the corrosion resistance of the alloy was improved to some extent as verified by immersion test and potentiodynamic polarization test in 3.5 wt.% NaCl solution at pH 7.0. X-ray diffraction patterns of the stannate treated AZ91D alloy showed the presence of MgSnO 3 · H 2 O, and SEM images indicated a porous structure, which provided advantage for the adsorption during sensitisation treatment prior to electroless nickel plating. A nickel coating with high phosphorus content was successfully deposited on the chemical conversion coating pre-applied to AZ91D alloy. The presence of the conversion coating between the nickel coating and the substrate reduced the potential difference between them and enhanced the corrosion resistance of the alloy. An obvious passivation occurred for the nickel coating during anodic polarization in 3.5 wt.% NaCl solution

Developing Carbon Budgets for Cities: Phoenix as a Case Study

Science.gov (United States)

McHale, M. R.; Baker, L. A.; Koerner, B. A.; Grimm, N. B.

2008-12-01

Studies have shown that cities can alter regional carbon dynamics through changing ecosystem productivity, overall carbon cycling rate, and total carbon storage in vegetation and soils. Furthermore, people in urban regions import a large amount of carbon in food and fuel, as well as release an exceptional amount of CO2 into the atmosphere. Numerous studies have attempted to quantify some sources and sinks of carbon in urban areas, although a complete carbon budget for a city that accounts for total inputs, outputs, and storage within the ecosystem has yet to be fully accomplished. One challenge is associated with attaining the data necessary to accurately account for all carbon dynamics in these heterogeneous and complex ecosystems. Our goal was to estimate a budget for the Phoenix metropolitan area while developing methodology to calculate carbon dynamics in urban systems that can be applied to cities across the US. Only with comparable carbon budgets for multiple cities will we finally begin to understand the influence of urbanization on carbon dynamics. Our analysis shows when calculating certain variables like transportation emissions, results can vary radically (up to 250%) depending on the data source and methodology implemented (i.e. bottom-up vs. top-down). A common assumption is that productivity and carbon storage will increase with urbanization in arid systems due to water and nutrient inputs, as well as changes in vegetation structure; however, our results indicated that this may not actually be the case in Phoenix where a large number of residents design landscapes to conserve water. Even if all urban expansion was dedicated to landscapes designed for carbon sequestration and storage, vegetation and soils will unlikely have a large effect on the C budget without significant changes in transportation and lifestyle choices.

Qualitative Research of AZ31 Magnesium Alloy Aircraft Brackets Produced by a New Forging Method

Directory of Open Access Journals (Sweden)

Dziubińska A.

2016-06-01

Full Text Available The paper reports a selection of numerical and experimental results of a new closed-die forging method for producing AZ31 magnesium alloy aircraft brackets with one rib. The numerical modelling of the new forming process was performed by the finite element method.The distributions of stresses, strains, temperature and forces were examined. The numerical results confirmed that the forgings produced by the new forming method are correct. For this reason, the new forming process was verified experimentally. The experimental results showed good agreement with the numerical results. The produced forgings of AZ31 magnesium alloy aircraft brackets with one rib were then subjected to qualitative tests.

Fatigue characteristics of sand-cast AZ91D magnesium alloy

Directory of Open Access Journals (Sweden)

Zhenming Li

2017-03-01

Full Text Available The fatigue characteristics of the AZ91D-T6 alloy samples taken from engine blocks have been investigated at 20 °C and elevated temperature (150 °C. The fatigue strength and cyclic stress amplitude of the alloy significantly decrease with the increase of the test temperature, although cyclic hardening occurs continuously until failure for both temperatures. With the increase of the temperature, the decreased fatigue life of the alloy tested at the same stress amplitude is mainly attributed to the decreased matrix strength and the increased hysteresis energies. Fatigue failure of the engine blocks made of AZ91D-T6 alloy is mainly controlled by casting defects. For the defect-free specimens, the crack initiation behavior is determined by the single-slip (20 °C and by environment-assisted cyclic slip (150 °C during fatigue, respectively. The low-cycle fatigue lives of the alloy can be predicted using the Coffin-Manson relation and Basquin laws, the three-parameter equation and the energy-based concepts, while the high-cycle fatigue lives of the alloy fitted well with the developed long crack life model and MSF life models.

Lysobacter capsici AZ78 produces cyclo(L-Pro-L-Tyr), a 2,5-diketopiperazine with toxic activity against sporangia of Phytophthora infestans and Plasmopara viticola.

Science.gov (United States)

Puopolo, G; Cimmino, A; Palmieri, M C; Giovannini, O; Evidente, A; Pertot, I

2014-10-01

To investigate low molecular weight compounds produced in vitro by Lysobacter capsici AZ78 and their toxic activity against sporangia of plant pathogenic oomycetes. Assays carried out in vitro showed that L. capsici AZ78 drastically inhibits the growth of plant pathogenic oomycetes. Accordingly, the preventive application of culture filtrates of L. capsici AZ78 on grapevine and tomato plants reduced the infections, respectively, caused by Plasmopara (Pl.) viticola and Phytophthora infestans. The subsequent chemical analysis of the culture filtrates of L. capsici AZ78 by spectroscopic (essentially 1D and 2D (1)H NMR and (13)C NMR and ESI MS spectra) and optical methods led to the identification of the 2,5-diketopiperazine cyclo(L-Pro-L-Tyr) that inhibited the development of P. infestans sporangia in vitro and on tomato leaves. Furthermore, a genomic region with high sequence identity with genes coding for a hybrid polyketide synthase and nonribosomal peptide synthetase was detected in L. capsici AZ78. Lysobacter capsici AZ78 produces cyclo(L-Pro-L-Tyr) in vitro that was effective in killing the sporangia of P. infestans and Pl. viticola in vitro. Moreover, this low molecular weight compound prevents the occurrence of late blight lesions when applied on tomato leaves. The application of L. capsici AZ78 cells or its own culture filtrates effectively controls both P. infestans and Pl. viticola. Cyclo(L-Pro-L-Tyr) produced by L. capsici AZ78 is toxic against sporangia of both these oomycetes. These data enforce the potential in the use of Lysobacter members for the control of plant pathogenic oomycetes and provide the basis for the development of new low-impact fungicides based on cyclo(L-Pro-L-Tyr). © 2014 The Society for Applied Microbiology.

Evaluación de la mezcla de ametrina + clomazone en caña de azúcar

Directory of Open Access Journals (Sweden)

Valent\\u00EDn A. Esqueda

2001-01-01

Full Text Available caña de azúcar. Se estableció un experimento en el Rancho Casablanca, Municipio de Puente Nacional, en el estado de Veracruz, México, para evaluar la toxicidad ocasionada por la mezcla de los herbicidas ametrina + clomazone a las variedades de caña de azúcar MEX-79-431, MEX-69-290, MEX-68- P23 y CP-72-2086. Se evaluaron cuatro tratamientos de control de malezas: 1. Ametrina + clomazone (1200 + 800 g/ha, 2. Ametrina + clomazone (1800 + 1200 g/ha, 3. Ametrina + 2,4-D (1225 + 650 g/ha y 4. Testigo limpio. Los herbicidas se aplicaron cuando la caña de azúcar tenía entre dos y cuatro hojas. La mezcla de ametrina + clomazone ocasionó blanqueamiento del follaje en todas las variedades de caña de azú- car. El área con blanqueamiento, varió entre el 36,3 y 47,5% con la dosis mas alta de esta mezcla; entre el 25 y 39,4%, con la dosis menor y prácticamente desapareció a los 45 días despu és de la aplicación. A su vez, la mezcla de ametrina + 2,4- D no ocasionó blanqueamiento. La toxicidad ocasionada por la mezcla de ametrina + clomazone no afectó el número de hojas por planta, el número de tallos en 2 m lineales y la altura de las plantas. Tampoco fueron afectados el rendimiento de tallos y el contenido de sacarosa

N terminus of Swr1 binds to histone H2AZ and provides a platform for subunit assembly in the chromatin remodeling complex.

Science.gov (United States)

Wu, Wei-Hua; Wu, Chwen-Huey; Ladurner, Andreas; Mizuguchi, Gaku; Wei, Debbie; Xiao, Hua; Luk, Ed; Ranjan, Anand; Wu, Carl

2009-03-06

Variant histone H2AZ-containing nucleosomes are involved in the regulation of gene expression. In Saccharomyces cerevisiae, chromatin deposition of histone H2AZ is mediated by the fourteen-subunit SWR1 complex, which catalyzes ATP-dependent exchange of nucleosomal histone H2A for H2AZ. Previous work defined the role of seven SWR1 subunits (Swr1 ATPase, Swc2, Swc3, Arp6, Swc5, Yaf9, and Swc6) in maintaining complex integrity and H2AZ histone replacement activity. Here we examined the function of three additional SWR1 subunits, bromodomain containing Bdf1, actin-related protein Arp4 and Swc7, by analyzing affinity-purified mutant SWR1 complexes. We observed that depletion of Arp4 (arp4-td) substantially impaired the association of Bdf1, Yaf9, and Swc4. In contrast, loss of either Bdf1 or Swc7 had minimal effects on overall complex integrity. Furthermore, the basic H2AZ histone replacement activity of SWR1 in vitro required Arp4, but not Bdf1 or Swc7. Thus, three out of fourteen SWR1 subunits, Bdf1, Swc7, and previously noted Swc3, appear to have roles auxiliary to the basic histone replacement activity. The N-terminal region of the Swr1 ATPase subunit is necessary and sufficient to direct association of Bdf1 and Swc7, as well as Arp4, Act1, Yaf9 and Swc4. This same region contains an additional H2AZ-H2B specific binding site, distinct from the previously identified Swc2 subunit. These findings suggest that one SWR1 enzyme might be capable of binding two H2AZ-H2B dimers, and provide further insight on the hierarchy and interdependency of molecular interactions within the SWR1 complex.

Microstructural evolution and tensile mechanical properties of thixoformed AZ91D magnesium alloy with the addition of yttrium

International Nuclear Information System (INIS)

Zhao Zude; Chen Qiang; Kang Feng; Shu Dayu

2009-01-01

The microstructure evolution of AZ91D magnesium alloy in the semi-solid state has been proposed or reported in previous literature. However, no detailed investigation has been conducted regarding the relationship between the microstructure and tensile mechanical properties of the thixoformed AZ91D magnesium alloy. In this paper, the microstructure of AZ91D alloy with the addition of yttrium was produced by the semi-solid thermal transformation (SSTT) route and the strain-induced melt activation (SIMA) route, respectively. Isothermal holding experiments investigated grain coarsening and the degree of spheroidization as a function of holding time in the semi-solid state. The SSTT route and the SIMA route were used to obtain the semi-solid feedstock for thixoforming. The results show that solid particles of the SSTT alloy are spheroidized to some extent but the previous irregular shape is still obvious in some of them. While the SIMA alloy exhibits ideal, fine microstructure, in which completely spheroidized solid particles contain little entrapped liquid. The microstructure of the SSTT alloy is less spheroidized compared with the SIMA alloy under the similar isothermal holding condition. As the holding time increases, the mean solid particle size of the SSTT alloy decreases initially, then increases, while the mean solid particle size of the SIMA alloy increases monotonously at 560 deg. C. Compared with the SSTT alloy, the SIMA alloy obtains finer grains under the similar isothermal holding condition. The mechanical properties of the thixoformed AZ91D alloy with the addition of yttrium produced by the SIMA route are better than those of the thixoformed alloy produced by the SSTT route. The ultimate tensile strength, yield strength and elongation for the thixoformed alloy produced by the SIMA route are 303.1 MPa, 147.6 MPa and 13.27%, respectively. The tensile properties for the AZ91D alloy with the addition of yttrium thixoformed from starting material produced by

Mechanical properties of AZ31 alloy processed by a green metallurgy route; Propiedades mecanicas de la aleacion AZ31 procesada por una ruta eco-sostenible

Energy Technology Data Exchange (ETDEWEB)

D' Enrico, F.; Garces, G.; Hofer, M.; Kim, S. K.; Perez, P.; Cabeza, S.; Adeva, P.

2013-07-01

Recently it has been proved that molding of defect-free components of various commercial alloys of magnesium can be carried out successfully when small amounts of CaO are added to the melt, making unnecessary the use of SF{sub 6} coverage. In the case of AZ alloys, this process also remarkably improves their mechanical properties not only by the greater cleaning of alloys but also by the formation of CaAl{sub 2} phase. This work, part of the Green project Metallurgy (http://www.green-metallurgy.eu) funded by the European Union (LIFE+2009), studies the influence of different CaO additions on the microstructure and mechanical properties of AZ31 Eco-Mg alloy. The alloy was processed by a conventional route involving extrusion of as-cast rods as well as by a powder metallurgy route (PM) using chips as starting material. The objective was to analyze the viability of recycling machining chips to manufacture components for the automobile industry and transportation in general, because of its low cost and environmental impact. It has been demonstrated that alloys processed from chips exhibit the highest tensile stress values, close to 320 MPa. (Author)

Historical evidence of the Spanish introduction of date palm (Phoenix dactylifera L., Arecaceae) into the Americas

Science.gov (United States)

America’s date palm (Phoenix dactylifera L.) groves can be found from 36o N Lat. (USA) to 21o S Lat. (Chile) and from 63o W Long. (Venezuela) to 117o W Long. (USA), at elevations from sea level 2000 m (Colombia). However, successful production of ripe dates is possible only in the arid regions of Pe...

CSER 96-014: criticality safety of project W-151, 241-AZ-101 retrieval system process test

Energy Technology Data Exchange (ETDEWEB)

Vail, T.S., Fluor Daniel Hanford

1997-02-06

This Criticality Safety Evaluation Report (CSER) documents a review of the criticality safety implications of a process test to be performed in tank 241-AZ-101 (101-AZ). The process test will determine the effectiveness of the retrieval system for mobilization of solids and the practicality of the system for future use in the underground storage tanks at Hanford. The scope of the CSER extends only to the testing and operation of the mixer pumps and does not include the transfer of waste from the tank. Justification is provided that a nuclear criticality is extremely unlikely, if not impossible, in this tank.

Effect of Mucin and Bicarbonate Ion on Corrosion Behavior of AZ31 Magnesium Alloy for Airway Stents

Directory of Open Access Journals (Sweden)

Yongseok Jang

2014-08-01

Full Text Available The biodegradable ability of magnesium alloys is an attractive feature for tracheal stents since they can be absorbed by the body through gradual degradation after healing of the airway structure, which can reduce the risk of inflammation caused by long-term implantation and prevent the repetitive surgery for removal of existing stent. In this study, the effects of bicarbonate ion (HCO3− and mucin in Gamble’s solution on the corrosion behavior of AZ31 magnesium alloy were investigated, using immersion and electrochemical tests to systematically identify the biodegradation kinetics of magnesium alloy under in vitro environment, mimicking the epithelial mucus surfaces in a trachea for development of biodegradable airway stents. Analysis of corrosion products after immersion test was performed using scanning electron microscopy (SEM, energy dispersive X-ray spectroscopy (EDX and X-ray diffraction (XRD. Electrochemical impedance spectroscopy (EIS was used to identify the effects of bicarbonate ions and mucin on the corrosion behavior of AZ31 magnesium alloys with the temporal change of corrosion resistance. The results show that the increase of the bicarbonate ions in Gamble’s solution accelerates the dissolution of AZ31 magnesium alloy, while the addition of mucin retards the corrosion. The experimental data in this work is intended to be used as foundational knowledge to predict the corrosion behavior of AZ31 magnesium alloy in the airway environment while providing degradation information for future in vivo studies.

Microstructure characteristics and effect of aging process on the mechanical properties of squeeze-cast AZ91 alloy

International Nuclear Information System (INIS)

Han, G.M.; Han, Z.Q.; Luo, A.A.; Liu, B.C.

2015-01-01

Highlights: • Characterization of three-dimensional morphologies of precipitates using AFM. • Quantitative microstructure of aged squeeze-cast AZ91 alloy. • The non-uniform continuous precipitation during aging of squeeze-cast AZ91 alloy. • The relationship between microstructure and property of aged squeeze-cast AZ91 alloy. - Abstract: Quantitative microstructure information is critical to modeling and prediction of mechanical properties of structural components. In this study, the microstructure characteristics of aged squeeze-cast AZ91 alloy were investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atomic force microscopy (AFM) analyses. Particularly, a study of the three-dimensional morphology of continuous precipitation during heat treatment was carried out using a combination of TEM and AFM. The results showed that a typical precipitate consisted of three kinds of faces, namely, broad, side, and end faces. The precipitate also presented a lath-shaped morphology with lozenge ends. Combined SEM and TEM analyses revealed quantitative information on the sizes and area number densities of precipitates after aging at different temperatures with different times. In general, the length and width of precipitates increased more rapidly than thickness during aging. The area number density initially increased and then slowly decreased because of coarsening. Furthermore, a special microstructure characteristic of the non-uniform continuous precipitation during aging was investigated using electron probe microanalysis (EPMA). The relationship between hardness response and yield strength was established

75 FR 11939 - DNS Electronics, Chandler, AZ; Notice of Termination of Investigation

Science.gov (United States)

2010-03-12

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-70,654] DNS Electronics, Chandler, AZ; Notice of Termination of Investigation Pursuant to Section 223 of the Trade Act of 1974, as... on behalf of workers of DNS Electronics, Chandler, Arizona. The petitioning group of workers is...

Genetic Diversity of Iraqi Date Palm (Phoenix ‎dactylifera L.) by using RAPD Technique

OpenAIRE

Muhanned Abdul Hasan Kareem; Ali Hmood Al-Saadi ‎; Hassan Fadhil Naji

2018-01-01

In this study provided all molecular markers of Random amplified polymorphic (RAPD) successfully with the sixty five Iraqi date palm (Phoenix dactylifera L.) cultivars, which collected from Hilla city in Iraq, to determine fingerprinting, polymorphic value, and relationships among varieties of date palm cultivars, and also with the same type of cultivars. Data analysis of ten RAPD has been revealed. Number of amplified DNA fragments were (592) bands, polymorphism per all primers were (%64.2),...

Genetic Diversity of Iraqi Date Palm (Phoenix ‎dactylifera L.) by using RAPD Technique

OpenAIRE

Muhanned Abdul Hasan; Ali ‎ Hmood Al-Saadi; Hassan Fadhil Naji

2017-01-01

In this study provided all molecular markers of Random amplified polymorphic (RAPD) successfully with the sixty five Iraqi date palm (Phoenix dactylifera L.) cultivars, which collected from Hilla city in Iraq, to determine fingerprinting, polymorphic value, and relationships among varieties of date palm cultivars, and also with the same type of cultivars. Data analysis of ten RAPD has been revealed. Number of amplified DNA fragments were (592) bands, polymorphism per all primers were (%64.2),...

Comportamiento frente a la corrosión y biocompatibilidad in vitro/in vivo de la aleación AZ31 modificada superficialmente

Directory of Open Access Journals (Sweden)

Escudero, M. L.

2011-06-01

Full Text Available The present work evaluates the corrosion behaviour and the in vitro/in vivo biocompatibility of the AZ31 magnesium alloy, which fulfills the mechanical requirements of bone. The corrosion kinetic of as-received AZ31 alloy was not compatible with the cell growth. To improve its performance, the AZ31 alloy was surface modified by a chemical conversion treatment in hydrofluoric acid. The magnesium fluoride layer generated by the surface treatment of AZ31 alloy enhances its corrosion behaviour, allowing the in vitro growth of osteoblastic cells over the surface and the in vivo formation of a highly compact layer of new bone tissue. These results lead to consider the magnesium fluoride coating as necessary for potential use of the AZ31 alloy as biodegradable and absorbable implant for bone repair.En el presente trabajo se ha estudiado el comportamiento frente a la corrosión y la biocompatibilidad in vitro/in vivo de la aleación de magnesio AZ31, cuyas propiedades mecánicas son superiores a los requisitos mecánicos del hueso. La aleación en estado de recepción ha mostrado una cinética de corrosión no compatible con el crecimiento celular. Para mejorar su comportamiento, el material ha sido modificado superficialmente mediante tratamiento de conversión química en ácido fluorhídrico. La capa de fluoruro de magnesio generada tras este tratamiento mejora el comportamiento del material frente a la corrosión, permitiendo el crecimiento in vitro de células osteoblásticas sobre su superficie y la formación in vivo de una capa de nuevo tejido óseo muy compacta. Estos resultados permiten concluir que el recubrimiento de fluoruro de magnesio es necesario para que el material AZ31 pueda ser potencialmente aplicado como implante biodegradable y reabsorbible en reparaciones óseas.

Preparation and characterization of inorganic and organic coatings on AZ91D magnesium alloy with electroless plating pretreatment

Energy Technology Data Exchange (ETDEWEB)

Zhang, S.Y.; Li, Q.; Zhang, H.X.; Wang, S.Y.; Liu, F. [School of Chemistry and Chemical Engineering, Southwest University Chongqing, 400715 (China); Yang, X.K. [School of Materials Science and Engineering, Southwest University Chongqing, 400715 (China)

2011-09-15

In this paper, a protective coating scheme was applied for the corrosion protection of AZ91D magnesium alloy. Electroless Ni coating (EN coating) as bottom layer, electrodeposited Ni coating (ENN coating), and silane-based coating (ENS coating) as top layer, respectively, were successfully prepared on AZ91D magnesium alloy by combination techniques. Scanning electron microscopy and X-ray diffraction were employed to investigate the surface and phase structure of coatings, respectively. The electrochemical corrosion behaviors of coatings in neutral 3.5 wt% NaCl solution were evaluated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization techniques. The corrosion testing showed that the three kinds of coatings all could provide corrosion protection for AZ91D magnesium alloy to a certain extent, and the corrosion resistance of ENN and ENS was superior to EN. In order to further study the corrosion protection properties of ENN and ENS, a comparative investigation on the evolution of EIS of ENN and ENS was carried out by dint of immersion test in neutral 3.5 wt% NaCl solution. The results indicated that, compared with ENN, the ENS could provide longer corrosion protection for AZ91D magnesium alloy. It is significant to determine the barrier effect of each coating, which could provide reference for industry applications. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Pump Jet Mixing and Pipeline Transfer Assessment for High-Activity Radioactive Wastes in Hanford Tank 241-AZ-102

Energy Technology Data Exchange (ETDEWEB)

Y Onishi; KP Recknagle; BE Wells

2000-08-09

The authors evaluated how well two 300-hp mixer pumps would mix solid and liquid radioactive wastes stored in Hanford double-shell Tank 241-AZ-102 (AZ-102) and confirmed the adequacy of a three-inch (7.6-cm) pipeline system to transfer the resulting mixed waste slurry to the AP Tank Farm and a planned waste treatment (vitrification) plant on the Hanford Site. Tank AZ-102 contains 854,000 gallons (3,230 m{sup 3}) of supernatant liquid and 95,000 gallons (360 m{sup 3}) of sludge made up of aging waste (or neutralized current acid waste). The study comprises three assessments: waste chemistry, pump jet mixing, and pipeline transfer. The waste chemical modeling assessment indicates that the sludge, consisting of the solids and interstitial solution, and the supernatant liquid are basically in an equilibrium condition. Thus, pump jet mixing would not cause much solids precipitation and dissolution, only 1.5% or less of the total AZ-102 sludge. The pump jet mixing modeling indicates that two 300-hp mixer pumps would mobilize up to about 23 ft (7.0 m) of the sludge nearest the pump but would not erode the waste within seven inches (0.18 m) of the tank bottom. This results in about half of the sludge being uniformly mixed in the tank and the other half being unmixed (not eroded) at the tank bottom.

Pump Jet Mixing and Pipeline Transfer Assessment for High-Activity Radioactive Wastes in Hanford Tank 241-AZ-102

International Nuclear Information System (INIS)

Onishi, Y.; Recknagle, K.P.; Wells, B.E.

2000-01-01

The authors evaluated how well two 300-hp mixer pumps would mix solid and liquid radioactive wastes stored in Hanford double-shell Tank 241-AZ-102 (AZ-102) and confirmed the adequacy of a three-inch (7.6-cm) pipeline system to transfer the resulting mixed waste slurry to the AP Tank Farm and a planned waste treatment (vitrification) plant on the Hanford Site. Tank AZ-102 contains 854,000 gallons (3,230 m 3 ) of supernatant liquid and 95,000 gallons (360 m 3 ) of sludge made up of aging waste (or neutralized current acid waste). The study comprises three assessments: waste chemistry, pump jet mixing, and pipeline transfer. The waste chemical modeling assessment indicates that the sludge, consisting of the solids and interstitial solution, and the supernatant liquid are basically in an equilibrium condition. Thus, pump jet mixing would not cause much solids precipitation and dissolution, only 1.5% or less of the total AZ-102 sludge. The pump jet mixing modeling indicates that two 300-hp mixer pumps would mobilize up to about 23 ft (7.0 m) of the sludge nearest the pump but would not erode the waste within seven inches (0.18 m) of the tank bottom. This results in about half of the sludge being uniformly mixed in the tank and the other half being unmixed (not eroded) at the tank bottom

The extrusion of AZ-series magnesium alloys - extending the processing limits by hydrostatic extrusion; Erweiterung der Prozessgrenzen beim Strangpressen von Magnesiumknetlegierungen der AZ-Reihe durch das hydrostatische Strangpressverfahren

Energy Technology Data Exchange (ETDEWEB)

Swiostek, J. [GKSS-Forschungszentrum Geesthacht GmbH (Germany). Inst. fuer Werkstofforschung

2008-12-04

The present study is concerned with the analysis of the influence of hydrostatic extrusion on the microstructural development and mechanical properties of extruded profiles of the AZ-series magnesium alloys. This work also deals with the correlation between the microstructure and resulting mechanical properties for the case extruded profiles. (orig.)

EnviroAtlas - Phoenix, AZ - Estimated Percent Green Space Along Walkable Roads

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates green space along walkable roads. Green space within 25 meters of the road centerline is included and the percentage is based on...

EnviroAtlas - Phoenix, AZ - Estimated Percent Tree Cover Along Walkable Roads

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset estimates tree cover along walkable roads. The road width is estimated for each road and percent tree cover is calculated in a 8.5 meter...

Cerium Addition Improved the Dry Sliding Wear Resistance of Surface Welding AZ91 Alloy

Directory of Open Access Journals (Sweden)

Qingqiang Chen

2018-02-01

Full Text Available In this study, the effects of cerium (Ce addition on the friction and wear properties of surface welding AZ91 magnesium alloys were evaluated by pin-on-disk dry sliding friction and wear tests at normal temperature. The results show that both the friction coefficient and wear rate of surfacing magnesium alloys decreased with the decrease in load and increase in sliding speed. The surfacing AZ91 alloy with 1.5% Ce had the lowest friction coefficient and wear rate. The alloy without Ce had the worst wear resistance, mainly because it contained a lot of irregularly shaped and coarse β-Mg17Al12 phases. During friction, the β phase readily caused stress concentration and thus formed cracks at the interface between β phase and α-Mg matrix. The addition of Ce reduced the size and amount of Mg17Al12, while generating Al4Ce phase with a higher thermal stability. The Al-Ce phase could hinder the grain-boundary sliding and migration and reduced the degree of plastic deformation of subsurface metal. Scanning electron microscopy observation showed that the surfacing AZ91 alloy with 1.5% Ce had a total of four types of wear mechanism: abrasion, oxidation, and severe plastic deformation were the primary mechanisms; delamination was the secondary mechanism.

Flow behaviour of magnesium alloy AZ31B processed by equal-channel angular pressing

International Nuclear Information System (INIS)

Arun, M S; Chakkingal, U

2014-01-01

Magnesium alloys are characterised by their low density, high specific strength and stiffness. But, the potential application of Mg is limited by its low room-temperature ductility and formability. Formability can be improved by developing an ultrafine grained (UFG) structure. Equal channel angular pressing (ECAP) is a well known process that can be used to develop an ultrafine grained microstructure. The aim of this study was to investigate the flow behaviour of AZ31B magnesium alloy after ECAP. The specimen was subjected to three passes of ECAP with a die angle of 120° using processing route Bc. The processing temperature was 523 K for the first pass and 423 K for the subsequent two passes. The microstructure characterisation was done. Compression tests of ECAPed and annealed specimens were carried out at strain rates of 0.01 – 1s −1 and deformation temperatures of 200 – 300°C using computer servo-controlled Gleeble-3800 system. The value of activation energy Q and the empirical materials constants of A and n were determined. The equations relating flow stress and Zener-Hollomon parameter were proposed. In the case annealed AZ31, the activation energy was determined to be 154 kJ/mol, which was slightly higher than the activation energy of 144 kJ/mol for ECAPed AZ31

Flow behaviour of magnesium alloy AZ31B processed by equal-channel angular pressing

Science.gov (United States)

Arun, M. S.; Chakkingal, U.

2014-08-01

Magnesium alloys are characterised by their low density, high specific strength and stiffness. But, the potential application of Mg is limited by its low room-temperature ductility & formability. Formability can be improved by developing an ultrafine grained (UFG) structure. Equal channel angular pressing (ECAP) is a well known process that can be used to develop an ultrafine grained microstructure. The aim of this study was to investigate the flow behaviour of AZ31B magnesium alloy after ECAP. The specimen was subjected to three passes of ECAP with a die angle of 120° using processing route Bc. The processing temperature was 523 K for the first pass and 423 K for the subsequent two passes. The microstructure characterisation was done. Compression tests of ECAPed and annealed specimens were carried out at strain rates of 0.01 - 1s-1 and deformation temperatures of 200 - 300°C using computer servo-controlled Gleeble-3800 system. The value of activation energy Q and the empirical materials constants of A and n were determined. The equations relating flow stress and Zener-Hollomon parameter were proposed. In the case annealed AZ31, the activation energy was determined to be 154 kJ/mol, which was slightly higher than the activation energy of 144 kJ/mol for ECAPed AZ31.

Electrodeposition of Al-Mn alloy on AZ31B magnesium alloy in molten salts

International Nuclear Information System (INIS)

Zhang Jifu; Yan Chuanwei; Wang Fuhui

2009-01-01

The Al-Mn alloy coatings were electrodeposited on AZ31B Mg alloy in AlCl 3 -NaCl-KCl-MnCl 2 molten salts at 170 deg. C aiming to improve the corrosion resistance. However, in order to prevent AZ31B Mg alloy from corrosion during electrodeposition in molten salts and to ensure excellent adhesion of coatings to the substrate, AZ31B Mg alloy should be pre-plated with a thin zinc layer as intermediate layer. Then the microstructure, composition and phase constituents of the coatings were investigated by scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDX), and X-ray diffraction (XRD). It was indicated that, by adjusting the MnCl 2 content in the molten salts from 0.5 wt% to 2 wt%, the Mn content in the alloy coating was increased and the phase constituents were changed from f.c.c Al-Mn solid solution to amorphous phase. The corrosion resistance of the coatings was evaluated by potentiodynamic polarization measurements in 3.5% NaCl solution. It was confirmed that the Al-Mn alloy coatings exhibited good corrosion resistance with a chear passive region and significantly reduced corrosion current density at anodic potentiodynamic polarization. The corrosion resistance of the alloy coatings was also related with the microstructure and Mn content of the coatings.

Laser cladding of Zr-based coating on AZ91D magnesium alloy for ...

Indian Academy of Sciences (India)

based coating made of Zr powder was fabricated on AZ91D magnesium alloy by laser cladding. The microstructure of the coating was characterized by XRD, SEM and TEM techniques. The wear resistance of the coating was evaluated under dry ...

241-AZ-101 Waste Tank Color Video Camera System Shop Acceptance Test Report

Energy Technology Data Exchange (ETDEWEB)

WERRY, S.M.

2000-03-23

This report includes shop acceptance test results. The test was performed prior to installation at tank AZ-101. Both the camera system and camera purge system were originally sought and procured as a part of initial waste retrieval project W-151.

241-AZ-101 Waste Tank Color Video Camera System Shop Acceptance Test Report

International Nuclear Information System (INIS)

WERRY, S.M.

2000-01-01

This report includes shop acceptance test results. The test was performed prior to installation at tank AZ-101. Both the camera system and camera purge system were originally sought and procured as a part of initial waste retrieval project W-151

The Corrosion Protection of Magnesium Alloy AZ31B

Science.gov (United States)

Danford, M. D.; Mendrek, M. J.; Mitchell, M. L.; Torres, P. D.

1997-01-01

Corrosion rates for bare and coated Magnesium alloy AZ31B have been measured. Two coatings, Dow-23(Trademark) and Tagnite(Trademark), have been tested by electrochemical methods and their effectiveness determined. Electrochemical methods employed were the scanning reference electrode technique (SRET), the polarization resistance technique (PR) and the electrochemical impedance spectroscopy technique (EIS). In addition, general corrosion and stress corrosion methods were employed to examine the effectiveness of the above coatings in 90 percent humidity. Results from these studies are presented.

Parallel implementation of the PHOENIX generalized stellar atmosphere program. II. Wavelength parallelization

International Nuclear Information System (INIS)

Baron, E.; Hauschildt, Peter H.

1998-01-01

We describe an important addition to the parallel implementation of our generalized nonlocal thermodynamic equilibrium (NLTE) stellar atmosphere and radiative transfer computer program PHOENIX. In a previous paper in this series we described data and task parallel algorithms we have developed for radiative transfer, spectral line opacity, and NLTE opacity and rate calculations. These algorithms divided the work spatially or by spectral lines, that is, distributing the radial zones, individual spectral lines, or characteristic rays among different processors and employ, in addition, task parallelism for logically independent functions (such as atomic and molecular line opacities). For finite, monotonic velocity fields, the radiative transfer equation is an initial value problem in wavelength, and hence each wavelength point depends upon the previous one. However, for sophisticated NLTE models of both static and moving atmospheres needed to accurately describe, e.g., novae and supernovae, the number of wavelength points is very large (200,000 - 300,000) and hence parallelization over wavelength can lead both to considerable speedup in calculation time and the ability to make use of the aggregate memory available on massively parallel supercomputers. Here, we describe an implementation of a pipelined design for the wavelength parallelization of PHOENIX, where the necessary data from the processor working on a previous wavelength point is sent to the processor working on the succeeding wavelength point as soon as it is known. Our implementation uses a MIMD design based on a relatively small number of standard message passing interface (MPI) library calls and is fully portable between serial and parallel computers. copyright 1998 The American Astronomical Society

Dry Sliding Wear Charactristics of Aluminum 6061-T6, Magnesium AZ31 and Rock Dust Composite

Science.gov (United States)

Balachandar, R.; Balasundaram, R.; Rajkumar, G.

2018-02-01

In recent years, the use of aluminum composite is gaining popularity in a wide range of applications like automobiles, aerospace and constructions (both interior & exterior) panels etc., due to its high strength, low density characteristics. Various reinforcing materials are used with aluminum 6061-T6 in order to have better mechanical properties. The addition of 0.3% of magnesium AZ31 will increase the ultimate tensile strength by 25 %. The reinforcement of rock dust will decrease the density. Hence, in order to have an advantages of magnesium AZ31 and rock dust, in this work, these two constitutes are varied from 1% to 2% on the base material of Al6061-T6 in stir casting. To evaluate the wear characteristics, Pin on disc is used in these composites. The input parameters are speed, time & load. The output response is wear. To minimize the number of experiments, L9 orthogonal array is used. The test results showed that a composite of 97% of Al (6061-T6), 1% Mg (AZ31) & 2 % of rock dust produced less wear. To find the best value of operating parameter for each sample, ANN-GA is used.

Knox named Phoenix associate dean of faculty affairs

Directory of Open Access Journals (Sweden)

Robbins RA

2016-12-01

Full Text Available No abstract available. Article truncated after 150 words. The University of Arizona College of Medicine-Phoenix has announced the appointment of nationally recognized physician-scientist Kenneth S. Knox, MD, as the associate dean of faculty affairs. Dr. Knox who has been at the University of Arizona-Tucson since 2008, will oversee the Faculty Affairs Office whose charge is to promote an engaged, diverse community of faculty and scholars that sustain a culture of engagement, professionalism and inclusion. He also will serve as director of research at the Banner Lung Institute. Dr. Knox is a pulmonologist known for his research in sarcoidosis, fungal diagnostics and immunologic lung disease. His work includes developing treatments for HIV, AIDS and valley fever. The division chief of Pulmonary, Allergy, Critical Care and Sleep Medicine in Tucson, Knox was responsible for dramatic growth. His accomplishments include increasing the number of clinical and basic science faculty from five to 30 and fellowship trainings from six to 20, rekindling …

Project W-314 specific test and evaluation plan for AZ tank farm upgrades

International Nuclear Information System (INIS)

Hays, W.H.

1998-01-01

The purpose of this Specific Test and Evaluation Plan (STEP) is to provide a detailed written plan for the systematic testing of modifications made by the addition of the SN-631 transfer line from the AZ-O1A pit to the AZ-02A pit by the W-314 Project. The STEP develops the outline for test procedures that verify the system's performance to the established Project design criteria. The STEP is a lower tier document based on the W-314 Test and Evaluation P1 an (TEP). Testing includes Validations and Verifications (e.g., Commercial Grade Item Dedication activities, etc), Factory Tests and Inspections (FTIs), installation tests and inspections, Construction Tests and Inspections (CTIs), Acceptance Test Procedures (ATPs), Pre-Operational Test Procedures (POTPs), and Operational Test Procedures (OTPs). The STEP will be utilized in conjunction with the TEP for verification and validation

El blocao (y el bloqueo de José Díaz Fernández

Directory of Open Access Journals (Sweden)

Luis Fernando Bueno Morillas

2015-06-01

Full Text Available El blocao (1928 fue la primera novela de José Díaz Fernández. Supuso un éxito editorial insólito hasta entonces porque reunía tres características novedosas: una actitud crítica ante la guerra de Marruecos, una integración de las novedades vanguardistas en la que su autor llamó literatura de avanzada y un posicionamiento del intelectual al lado de las reivindicaciones del pueblo. Sin embargo, aunque publicó otra novela un año después (La Venus mecánica, un libro teórico en el que definía la literatura que él propugnaba y practicaba (El nuevo romanticismo y algunas narraciones breves, Díaz Fernández se bloqueó y dejó la literatura narrativa que tan buenas expectativas levantó. Analizaremos las posibles causas de ese bloqueo.

El medievalismo fértil de Paloma Díaz-Mas

Directory of Open Access Journals (Sweden)

Rafael M. Mérida Jiménez

2001-01-01

Full Text Available The author of this article is concerned with trying to understand why Paloma Díaz-Mas, the writer of such an excellent novel as La tierra fértil (1999, has not received much critical attention. He underlines three main reasons. First, she does not live in Madrid or Barcelona and so she is far away from the main centres of cultural power. Second, she teaches Spanish literature in the Basque Country, a political and linguistic community which significantly differs from that of many other writers. Third, she writes historical novels, which does not appear to be very fashionable in Spain these days. Moreover, Díaz-Mas is a woman writer who does not make use of the most commonly available feminine patterns, and she does not seem to offer a model easy to include in a given feminist methodology either. However, Mérida-Jiménez argues that Paloma provides an intelligent deconstruction of “male authority” through subtle rhetorical means, as well as a representation of the weakness of his “domination” in very innovative ways, such as those derived from the dialectics between history and fiction, centrality and marginality, heterosexuality and homosexuality, individual and society, dream and reason or tradition and modernity.

Role of manganese on the grain refining efficiency of AZ91D magnesium alloy refined by Al4C3

International Nuclear Information System (INIS)

Liu Shengfa; Zhang Yuan; Han Hui

2010-01-01

A novel Mg-50% Al 4 C 3 (hereafter in wt.%) master alloy has been developed by powder in situ synthesis process, the role of manganese on the grain refining efficiency of AZ91D magnesium alloy refined by this master alloy has been investigated. X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDS) results show the existence of Al 4 C 3 particles in this master alloy. After addition of 0.6% Al 4 C 3 or combined addition of 0.6% Al 4 C 3 and 0.27% Mn, the average grain size of AZ91D decreased dramatically from 360 μm to 210 μm, and from 360 μm to130 μm, respectively. However, no further refinement of grain size was achieved with additional amount of Mn exceeding 0.27% for AZ91D alloy refined by 0.6% Al 4 C 3 in the present investigation. Al-C-O-Mn-Fe-rich intermetallic particles with an Al-C-O-rich coating film, often observed in the central region of magnesium grains of the AZ91D alloy treated by the combination of Al 4 C 3 and Mn, are proposed to be the potent nucleating substrates for primary α-Mg.

Outreach Opportunities for Early Career Scientists at the Phoenix ComiCon

Science.gov (United States)

Horodyskyj, L.; Walker, S. I.; Forrester, J. H.

2014-12-01

The Phoenix ComiCon (PCC) is a rapidly growing annual four-day pop culture event, featuring guests, costuming, exhibits, and discussion panels for popular sci-fi, fantasy, horror, and anime franchises. In 2013, PCC began experimenting with science discussion panels. The popularity of the science programming resulted in an expansion of the track for 2014, which Horodyskyj was responsible for coordinating. Thirty hours of programming were scheduled, including 25 discussion panels, NASA's FameLab, and a Mars room. Panelists included industry specialists, established scientists, STEM outreach enthusiasts, and early career scientists. The majority of the panelists were early career scientists recruited from planetary sciences and biology departments at ASU and UA. Panel topics included cosmology, biotechnology, artificial intelligence, space exploration, astrobiology, and the cross-linkages of each with pop culture. Formats consisted of Q&A, presentations, and interactive game shows. Although most panels were aimed at the general audience, some panels were more specialized. PCC 2014 attracted 77,818 attendees. The science programming received rave reviews from the audience, the PCC management, and the panelists themselves. Many panel rooms were filled to capacity and required crowd control to limit attendance. We observed the formation of science "groupies" who sought out the science panels exclusively and requested more information on other science public events in the Phoenix area. We distributed surveys to several select sessions to evaluate audience reasons for attending the science panels and their opinion of the scientists they observed. We will present the results of these surveys. As the PCC continues to grow at an exponential rate, the science programming will continue to expand. We will discuss ideas for continued expansion of the PCC science programming both to serve the public and as a unique public outreach opportunity for early career scientists.

Dictionary of electrical engineering. Power engineering, automation technology, measurement and control technology, mechatronics. English - German; Fachwoerterbuch Elektrotechnik. Energietechnik, Automatisierungstechnik, Mess-, Steuer- und Regelungstechnik, Mechatronik. Englisch - Deutsch

Energy Technology Data Exchange (ETDEWEB)

Heckler, H.

2007-07-01

The foreign-language vocabulary taught at school usually does not cover terms needed during professional life in electrical engineering. This comprehensive dictionary contains more than 60,000 electrotechnical and engineering terms - used in textbooks, manuals, data sheets, whitepapers and international standards. British English and American English spelling differences are identified. Terms used in IEC standards of the International Electrotechnical Commission are marked, allowing the reader to have easy access to the multilingual glossary of the IEC. This book contains the in-house dictionaries of the internationally operating companies Festo, KEB, Phoenix Contact, and Rittal. Topics: - Basic of electrical engineering, - Electrical power engineering, - Mechatronics, - Electrical drive engineering, - Electrical connection technology, - Automation technology, - Safety-related technology, - Information technology, - Measurement and control technology, - Explosion protection - Power plant technology, - Lightning and overvoltage protection. (orig.)

Surface characterization and cytocompatibility evaluation of silanized magnesium alloy AZ91 for biomedical applications

Directory of Open Access Journals (Sweden)

Agnieszka Witecka, Akiko Yamamoto, Henryk Dybiec and Wojciech Swieszkowski

2012-01-01

Full Text Available Mg alloys with high Al contents have superior corrosion resistance in aqueous environments, but poor cytocompatibility compared to that of pure Mg. We have silanized the cast AZ91 alloy to improve its cytocompatibility using five different silanes: ethyltriethoxysilane (S1, 3-aminopropyltriethoxysilane (S2, 3-isocyanatopyltriethoxysilane (S3, phenyltriethoxysilane (S4 and octadecyltriethoxysilane (S5. The surface hydrophilicity/hydrophobicity was evaluated by water contact angle measurements. X-ray photoelectron analysis was performed to investigate the changes in surface states and chemical composition. All silane reagents increased adsorption of the albumin to the modified surface. In vitro cytocompatibility evaluation revealed that silanization improved cell growth on AZ91 modified by silane S1. Measurement of the concentration of Mg2+ ions released during the cell culture indicated that silanization does not affect substrate degradation.

Arizona Libraries: Books to Bytes. Contributed Papers Presented at the AzLA Annual Conference (Phoenix, Arizona, November 17-18, 1995).

Science.gov (United States)

Hammond, Carol, Ed.

This document contains three papers presented at the 1995 Arizona Library Association conference. Papers include: (1) "ERLs and URLs: ASU Libraries Database Delivery Through Web Technology" (Dennis Brunning & Philip Konomos), which illustrates how and why the libraries at Arizona State University developed a world wide web server and…

High performance corrosion and wear resistant composite titanium nitride layers produced on the AZ91D magnesium alloy by a hybrid method

Directory of Open Access Journals (Sweden)

Michał Tacikowski

2014-09-01

Full Text Available Composite, diffusive titanium nitride layers formed on a titanium and aluminum sub-layer were produced on the AZ91D magnesium alloy. The layers were obtained using a hybrid method which combined the PVD processes with the final sealing by a hydrothermal treatment. The microstructure, resistance to corrosion, mechanical damage, and frictional wear of the layers were examined. The properties of the AZ91D alloy covered with these layers were compared with those of the untreated alloy and of some engineering materials such as 316L stainless steel, 100Cr6 bearing steel, and the AZ91D alloy subjected to commercial anodizing. It has been found that the composite diffusive nitride layer produced on the AZ91D alloy and then sealed by the hydrothermal treatment ensures the corrosion resistance comparable with that of 316L stainless steel. The layers are characterized by higher electrochemical durability which is due to the surface being overbuilt with the titanium oxides formed, as shown by the XPS examinations, from titanium nitride during the hydrothermal treatment. The composite titanium nitride layers exhibit high resistance to mechanical damage and wear, including frictional wear which is comparable with that of 100Cr6 bearing steel. The performance properties of the AZ91D magnesium alloy covered with the composite titanium nitride coating are substantially superior to those of the alloy subjected to commercial anodizing which is the dominant technique employed in industrial practice.

Laser cladding of Zr-based coating on AZ91D magnesium alloy for ...

Indian Academy of Sciences (India)

3Hubei Key Laboratory of Hydroelectric Machinery Design & Maintenance, ... To improve the wear and corrosion resistance of AZ91D magnesium alloy, Zr-based coating made of ... process that lead to inflammatory cascades which reduce bio- ... tions regarding their application as protective films on load- ... Experimental.

Sealing of PEO Coated AZ91 Magnesium Alloy Using La-Based Solutions

Directory of Open Access Journals (Sweden)

Luca Pezzato

2017-01-01

Full Text Available In this work, solutions containing lanthanum salts were used for a post-treatment of sealing to increase the corrosion resistance of PEO coated AZ91 alloy. PEO coatings were produced on samples of AZ91 magnesium alloy using an alkaline solution containing sodium hydroxide, sodium phosphates, and sodium silicates. The sealing treatment was performed in a solution containing 12 g/L of La(NO33 at pH 4 at different temperatures and for different treatment times. Potentiodynamic polarization test, an EIS test, showed that the sealing treatment with solution containing lanthanum nitrate caused a remarkable increase in the corrosion resistance. The corrosion behavior was correlated with the surface morphology and elemental composition evaluated with scanning electron microscope (SEM, X-ray diffraction (XRD, and X-ray photoelectron spectroscopy (XPS. In particular, the sealing treatment at 50°C for 30 min resulted in being the most promising to increase the corrosion properties of PEO treated samples because of the formation of a homogeneous sealing layer, mainly composed of La(OH3.

Surface roughness optimization in machining of AZ31 magnesium alloy using ABC algorithm

Directory of Open Access Journals (Sweden)

Abhijith

2018-01-01

Full Text Available Magnesium alloys serve as excellent substitutes for materials traditionally used for engine block heads in automobiles and gear housings in aircraft industries. AZ31 is a magnesium alloy finds its applications in orthopedic implants and cardiovascular stents. Surface roughness is an important parameter in the present manufacturing sector. In this work optimization techniques namely firefly algorithm (FA, particle swarm optimization (PSO and artificial bee colony algorithm (ABC which are based on swarm intelligence techniques, have been implemented to optimize the machining parameters namely cutting speed, feed rate and depth of cut in order to achieve minimum surface roughness. The parameter Ra has been considered for evaluating the surface roughness. Comparing the performance of ABC algorithm with FA and PSO algorithm, which is a widely used optimization algorithm in machining studies, the results conclude that ABC produces better optimization when compared to FA and PSO for optimizing surface roughness of AZ 31.

Study on fluidity of squeeze cast AZ91D magnesium alloy with different wall thicknesses

Directory of Open Access Journals (Sweden)

Chen Yun

2014-03-01

Full Text Available Rectangular cross-section specimens with different section thicknesses were prepared to study the influences of pouring temperature, mould temperature and squeeze velocity on the fluidity of squeeze cast AZ91D magnesium alloy by means of orthogonal test design method. The results show that pouring temperature, mould temperature and squeeze velocity can significantly affect the fluidity of magnesium alloy specimens with wall thickness no more than 4 mm, and the pouring temperature is the most influential factor on the fluidity of specimens with wall thickness of 1, 2 and 3 mm, while mould temperature is the one for specimens with wall thickness of 4 mm. Increasing pouring temperature between 700 °C and 750 °C is beneficial to the fluidity of AZ91D magnesium alloy, and increasing mould temperature significantly enhances the filling ability of thick (3 and 4 mm section castings. The fluidity of squeeze cast magnesium alloy increases with the increase of wall thickness. It is not recommended to produce magnesium alloy casting with wall thickness of smaller than 3 mm by squeeze cast process due to the poor fluidity. The software DPS was used to generate the regression model, and linear regression equations of the fluidity of squeeze cast AZ91D with different wall thicknesses are obtained using the test results.

Structural and electrochemical behavior of sol-gel ZrO2 ceramic film on chemically pre-treated AZ91D magnesium alloy

International Nuclear Information System (INIS)

Li Qing; Chen Bo; Xu Shuqiang; Gao Hui; Zhang Liang; Liu Chao

2009-01-01

In the present investigation sol-gel-based ZrO 2 ceramic film was obtained using zirconium acetate as the precursor material. The film was deposited on AZ91D magnesium alloy by a dip-coating technique. An uniform stannate conversion coating as chemical pretreatment was employed as an intermediate layer prior to deposition of the ZrO 2 film in order to provide advantage for the formation of sol-gel-based ZrO 2 layer. The corrosion properties, structure, composition and morphology of these coatings on AZ91D magnesium alloy were studied by potentiodynamic polarization tests, EIS, XRD, SEM, respectively. According to the electrochemical tests, the corrosion resistance of AZ91D magnesium alloy was found to be greatly improved by means of this new environment-friendly surface treatment.

Technology-Supported Performance Assessments for Middle School Geoscience

Science.gov (United States)

Zalles, D. R.; Quellmalz, E.; Rosenquist, A.; Kreikemeier, P.

2002-12-01

Under funding from the World Bank, the U.S. Department of Education, the National Science Foundation, and the Federal Government's Global Learning and Observations to Benefit the Environment Program (GLOBE), SRI International has developed and piloted web-accessible performance assessments that measure K-12 students' abilities to use learning technologies to reason with scientific information and communicate evidence-based conclusions to scientific problems. This presentation will describe the assessments that pertain to geoscience at the middle school level. They are the GLOBE Assessments and EPA Phoenix, an instantiation of SRI's model of assessment design known as Integrative Performance Assessments in Technology (IPAT). All are publicly-available on the web. GLOBE engages students in scientific data collection and observation about the environment. SRI's classroom assessments for GLOBE provide sample student assessment tools and frameworks that allow teachers and students to assess how well students can use the data in scientific inquiry projects. Teachers can use classroom assessment tools on the site to develop integrated investigations for assessing GLOBE within their particular science curricula. Rubrics are provided for measuring students' GLOBE-related skills, and alignments are made to state, national, and international science standards. Sample investigations are provided about atmosphere, hydrology, landcover, soils, earth systems, and visualizations. The IPAT assessments present students with engaging problems rooted in science or social science content, plus sets of tasks and questions that require them to gather relevant information on the web, use reasoning strategies to analyze and interpret the information, use spreadsheets, word processors, and other productivity tools, and communicate evidence-based findings and recommendations. In the process of gathering information and drawing conclusions, students are assessed on how well they can operate

Fatigue properties of magnesium alloy AZ91 processed by severe plastic deformation

Czech Academy of Sciences Publication Activity Database

Fintová, Stanislava; Kunz, Ludvík

2015-01-01

Roč. 42, FEB (2015), s. 219-228 ISSN 1751-6161 R&D Projects: GA ČR GAP108/10/2001 Institutional support: RVO:68081723 Keywords : AZ91 magnesium alloy * ECAP * Fatigue * Crack initiation Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 2.876, year: 2015 http://www.sciencedirect.com/science/article/pii/S1751616114003713

Unsteady-Flow Modeling for Emergency Shutdown of the CAP Canal

OpenAIRE

Clemmens, Bert; Wahlin, Brian; Shapiro, Marcus; Dent, Patrick

2016-01-01

The Central Arizona Project (CAP) is designed to bring about 1.9 ML of Colorado River water per year to Maricopa, Pima, and Pinal counties in Arizona. CAP carries water from the Colorado River at Lake Havasu toTucson. The CAP canal system is a 540 km long system of conveyance system aqueducts, tunnels, pumping plants,pipelines and a large reservoir (just north of Phoenix, AZ). Water is pumped uphill from the Colorado River. This study was conducted for the Hayden-Rhodes Aqueduct of the Centra...

Phoenix – A model-based Human Reliability Analysis methodology: Qualitative Analysis Procedure

International Nuclear Information System (INIS)

Ekanem, Nsimah J.; Mosleh, Ali; Shen, Song-Hua

2016-01-01

Phoenix method is an attempt to address various issues in the field of Human Reliability Analysis (HRA). Built on a cognitive human response model, Phoenix incorporates strong elements of current HRA good practices, leverages lessons learned from empirical studies, and takes advantage of the best features of existing and emerging HRA methods. Its original framework was introduced in previous publications. This paper reports on the completed methodology, summarizing the steps and techniques of its qualitative analysis phase. The methodology introduces the “Crew Response Tree” which provides a structure for capturing the context associated with Human Failure Events (HFEs), including errors of omission and commission. It also uses a team-centered version of the Information, Decision and Action cognitive model and “macro-cognitive” abstractions of crew behavior, as well as relevant findings from cognitive psychology literature and operating experience, to identify potential causes of failures and influencing factors during procedure-driven and knowledge-supported crew-plant interactions. The result is the set of identified HFEs and likely scenarios leading to each. The methodology itself is generic in the sense that it is compatible with various quantification methods, and can be adapted for use across different environments including nuclear, oil and gas, aerospace, aviation, and healthcare. - Highlights: • Produces a detailed, consistent, traceable, reproducible and properly documented HRA. • Uses “Crew Response Tree” to capture context associated with Human Failure Events. • Models dependencies between Human Failure Events and influencing factors. • Provides a human performance model for relating context to performance. • Provides a framework for relating Crew Failure Modes to its influencing factors.

Evaluation of waste temperatures in AWF tanks for bypass mode operation of the 702-AZ ventilation system (Project W-030)

International Nuclear Information System (INIS)

Sathyanarayana, K.

1997-01-01

This report describes the results of thermal hydraulic analysis performed to provide data in support of Project W-030 to startup new 702-AZ Primary Ventilation System. During the startup of W-030 system, the ventilation system will be operating in bypass mode. In bypass made of operation, the system is capable of supplying 1000 cfm total flow for all four AWF doubleshell tanks. The design of the W-030 system is based on the assumption that both the recirculation loop of the primary ventilation system and the secondary ventilation which provides cooling would be operating. However, during the startup neither the recirculation system nor the secondary ventilation system will be operating. A minimum flow of 100 cfm is required to prevent any flammable gas associated risk. The remaining 600 cfm flow can be divided among the four tanks as necessary to keep the peak sludge temperatures below the operating temperature limit. For the purpose of determining the minimum flow required for cooling each tank, the thermal hydraulic analysis is performed to predict the peak sludge temperatures in AY/AZ tanks under different ventilation flows. The heat load for AZ farm tanks is taken from characterization reports and for the AY farm tanks, the heat load was estimated by thermal analysis using the measured waste temperatures and the waste liquid evaporation rates. The tank 241-AZ-101 and the tank 241-AZ-102 have heat loads of 241,600 and 199,500 Btu/hr respectively. The tank 241-AY-101 and tank 241-AY-102 have heat loads of 41,000 and 33,000 Btu/hr respectively. Using the ambient meteorological conditions of temperature and relative humidity for the air and tank, some soil surface and the sludge levels reported in recent documents, the peak sludge and supernatant temperatures were predicted for various primary ventilation flows ranging from 100 to 400 cfm for AZ tanks and 100 and 150 cfm for AY tanks. The results of these thermal hydraulic analyses are presented. Based on the

VERTICAL MIXING AND CHEMISTRY OVER AN ARID URBAN SITE: FIRST RESULTS FROM AIRCRAFT OBSERVATIONS MADE DURING THE PHOENIX SUNRISE CAMPAIGN

International Nuclear Information System (INIS)

BERKOWITZ, C.M.; SPRINGSTON, S.R.; DORAN, J.C.; FAST, J.D.

2002-01-01

The role of boundary layer mixing is increasingly recognized as an important factor in determining the concentrations of ozone and other trace gases near the surface. While the concentrations at the surface can vary widely due to horizontal transport of chemical plumes, the boundary layer is also characterized by turbulence that follows a diurnal cycle in height and intensity. Surface oxidant concentrations can therefore undergo significant changes even in the absence of photochemistry. A central goal of the Phoenix 2001 Field Campaign was to study vertical mixing with the onset of convection and to quantify the effect of this mixing on chemistry within an urban boundary layer. As part of this study, a series of low altitude aircraft sampling flights were made over the Greater Phoenix area between June 16-30, 2001. The resulting observations, in conjunction with a series of surface measurements and meteorological observations, are being used to study the vertical transport and reactivity of ozone and ozone-precursors shortly after sunrise. Additional details of this campaign are given in Doran, et al. (2002). It was anticipated that turbulence over Phoenix at night would be suppressed as a result of cooling of the boundary layer over the city. By sampling shortly after sunrise, we hoped to collect measurements above the residual nocturnal stable layer and to continue sampling through the developmental period of a convectively active boundary layer. We report here on the first analysis of these observations, made from a Gulstream-1 (G-1) aircraft operated by the U.S. Department of Energy

An electron back-scattered diffraction study on the microstructure evolution of AZ31 Mg alloy during equal channel angular extrusion

International Nuclear Information System (INIS)

Jin Li; Lin Dongliang; Mao Dali; Zeng Xiaoqin; Ding Wenjiang

2006-01-01

Microstructure evolution of AZ31 Mg alloy during equal channel angular extrusion (ECAE) was investigated by electron back-scattered diffraction (EBSD). The grains of AZ31 Mg alloy were refined significantly after ECAE 1-8 passes at 498 K and the distributions of grain size tended to be more uniform with pass number increasing. Frequency of sub-boundaries and low angle grain boundaries (LAGBs) increased at initial stage of deformation, and sub-boundaries and LAGBs evolved into high angle grain boundaries (HAGBs) with further deformation, which resulted in the high frequency of HAGBs in the alloy after ECAE 8 passes. Preferred misorientation angle with frequency peak near 30 deg. and 90 deg. were observed. The frequency peaks were weak after ECAE 1 pass but became stronger with the increase of pass numbers. Micro-textures were formed in AZ31 microstructure during ECAE and were stronger with the pass number increasing

Analysis of Phoenix Anomalies and IV and V Findings Applied to the GRAIL Mission

Science.gov (United States)

Larson, Steve

2012-01-01

Analysis of patterns in IV&V findings and their correlation with post-launch anomalies allowed GRAIL to make more efficient use of IV&V services . Fewer issues. . Higher fix rate. . Better communication. . Increased volume of potential issues vetted, at lower cost. . Hard to make predictions of post-launch performance based on IV&V findings . Phoenix made sound fix/use as-is decisions . Things that were fixed eliminated some problems, but hard to quantify. . Broad predictive success in one area, but inverse relationship in others.

The effect of Ca and RE elements on the precipitation kinetics of Mg17Al12 phase during artificial aging of magnesium alloy AZ91

International Nuclear Information System (INIS)

Amir Esgandari, B.; Mehrjoo, H.; Nami, B.; Miresmaeili, S.M.

2011-01-01

Highlights: → Ca and RE elements decrease the precipitation rate during aging of AZ91 alloy. → Precipitation kinetics and mechanism during aging of the alloys were studied. → Effect of Ca and RE on creep properties of age hardened AZ91 alloy was studied. - Abstract: The effect of simultaneous alloying with Ca and rare earth (RE) elements on the age hardening kinetics of AZ91 was studied through the fitting of the Johnson-Mehl-Avrami (JMA) equation. The results showed that the addition of both Ca and RE elements not only suppress discontinuous precipitation of the Mg 17 Al 12 phase during the age hardening process, but also decrease the alloy hardness. Fitting the JMA equation to the experimental data indicated that the phase transformation during age hardening of an alloy variant containing both Ca and RE (at 170 deg. C and 190 deg. C) and standard AZ91 (at 170 deg. C) takes place by the nucleation of precipitates on dislocations. In contrast, the precipitation during age hardening of AZ91 at 190 deg. C occurs via nucleation at grain boundaries. Although it was observed that the creep strength of age hardened specimens are lower than that of the as cast specimens, but age hardening treatment has lower deleterious influence on the creep resistance of the alloy containing Ca and RE in comparison with conventional AZ91. This may be ascribed to the decreased precipitation rate resulting from the addition of both Ca and RE elements.

Corrosion performance of MAO coatings on AZ31 Mg alloy in simulated body fluid vs. Earle's Balance Salt Solution

Energy Technology Data Exchange (ETDEWEB)

Wilke, Benjamin M. [Department of Mechanical Engineering, PO Box 755905, University of Alaska Fairbanks, Fairbanks, AK 99775 (United States); Zhang, Lei, E-mail: lzhang14@alaska.edu [Department of Mechanical Engineering, PO Box 755905, University of Alaska Fairbanks, Fairbanks, AK 99775 (United States); Li, Weiping; Ning, Chengyun [School of Materials Science and Engineering, South China University of Technology, Guangzhou 510641 (China); Chen, Cheng-fu [Department of Mechanical Engineering, PO Box 755905, University of Alaska Fairbanks, Fairbanks, AK 99775 (United States); Gu, Yanhong [College of Mechanical Engineering, Beijing Institute of Petrochemical Technology, Beijing 102617 (China)

2016-02-15

Graphical abstract: - Highlights: • MAO coating is deposited on AZ31 Mg alloy by microarc oxidation. • Corrosion performance of MAO-coated AZ31 in EBSS vs. c-SBF is studied. • MAO-coated AZ31 exhibits enhanced corrosion resistance compared to bare AZ31. • Samples in EBSS show slower corrosion progression than the samples in c-SBF. • CO{sub 2} buffer and less chloride in EBSS cause corrosion rate gap in c-SBF and EBSS. - Abstract: Earle's Balance Salt Solution (EBSS) provides an alternative to the conventional simulated body fluids (c-SBF) and has been shown to better simulate the corrosion conditions in vivo. In this work, a series of tests were conducted to explore the corrosion performance of MAO-coated AZ31 samples in EBSS vs. c-SBF. Samples were produced by varying MAO process parameters and then immersed up to 21 days in both EBSS and c-SBF. The corrosion rates were evaluated by the electrochemical impedance spectroscopy and potentiodynamic scanning. Scanning electron microscope (SEM) was used to compare the progression of microcracks across the surface of the coatings. The evaluation of cross-sectional thickness showed an increase in MAO coating thickness with the process voltage. MAO samples with a thicker coating generally have higher impedance and lower current density at the initial immersion time point of 0.5 h. Samples in EBSS showed higher initial impedance and lower current density values as compared to c-SBF counterparts for all process groups. Samples in EBSS demonstrated a much slower corrosion rate than c-SBF samples because of the decreased chloride content and CO{sub 2} buffering mechanism of the EBSS.

Corrosion performance of MAO coatings on AZ31 Mg alloy in simulated body fluid vs. Earle's Balance Salt Solution

International Nuclear Information System (INIS)

Wilke, Benjamin M.; Zhang, Lei; Li, Weiping; Ning, Chengyun; Chen, Cheng-fu; Gu, Yanhong

2016-01-01

Graphical abstract: - Highlights: • MAO coating is deposited on AZ31 Mg alloy by microarc oxidation. • Corrosion performance of MAO-coated AZ31 in EBSS vs. c-SBF is studied. • MAO-coated AZ31 exhibits enhanced corrosion resistance compared to bare AZ31. • Samples in EBSS show slower corrosion progression than the samples in c-SBF. • CO 2 buffer and less chloride in EBSS cause corrosion rate gap in c-SBF and EBSS. - Abstract: Earle's Balance Salt Solution (EBSS) provides an alternative to the conventional simulated body fluids (c-SBF) and has been shown to better simulate the corrosion conditions in vivo. In this work, a series of tests were conducted to explore the corrosion performance of MAO-coated AZ31 samples in EBSS vs. c-SBF. Samples were produced by varying MAO process parameters and then immersed up to 21 days in both EBSS and c-SBF. The corrosion rates were evaluated by the electrochemical impedance spectroscopy and potentiodynamic scanning. Scanning electron microscope (SEM) was used to compare the progression of microcracks across the surface of the coatings. The evaluation of cross-sectional thickness showed an increase in MAO coating thickness with the process voltage. MAO samples with a thicker coating generally have higher impedance and lower current density at the initial immersion time point of 0.5 h. Samples in EBSS showed higher initial impedance and lower current density values as compared to c-SBF counterparts for all process groups. Samples in EBSS demonstrated a much slower corrosion rate than c-SBF samples because of the decreased chloride content and CO 2 buffering mechanism of the EBSS.

La Caña de Azúcar y sus Derivados en la Huasteca San Luís Potosí México

Directory of Open Access Journals (Sweden)

Noé Aguilar Rivera

2011-08-01

Full Text Available La caña de azúcar es el principal cultivo de México, su cosecha se lleva a cabo en 665,000 ha que ocupan a 2.5 millones de personas. Existen 57 ingenios azucareros localizados en 15 estados de la republica. La industria ha cambiado dramáticamente desde la introducción de la caña de azúcar hace 486 años (año 1523 y su situación es reflejo de su metamorfosis y de intereses económicos y políticos. Fueron los españoles quienes introdujeron la caña de azúcar y tomaron así ventajas de las condiciones favorables que México ofrecía para el cultivo y la comercialización de los productos de derivados de la caña de azúcar (melazas, azúcar, panela o piloncillo y aguardiente. Grandes plantaciones fueron establecidas en diversas áreas como la Huasteca Potosina (San Luis Potosí. Esas plantaciones modificaron no solo las condiciones de vida, además la constitución de cada una de esas sociedades. El cambio fue dramático debido a la gran cantidad de indígenas nativos y al interés de los españoles hacia otras mercancías como los minerales y otros cultivos. En este trabajo se presentan algunos aspectos de la evolución y las estrategias para el desarrollo de la industria azucarera en la Huasteca Potosina San Luis Potosí durante el Virreinato de Nueva España.

Development of liquid-nitrogen-cooling friction stir spot welding for AZ31 magnesium alloy joints

Science.gov (United States)

Wu, Dong; Shen, Jun; Zhou, Meng-bing; Cheng, Liang; Sang, Jia-xing

2017-10-01

A liquid-nitrogen-cooling friction stir spot welding (C-FSSW) technology was developed for welding AZ31 magnesium alloy sheets. The liquid-nitrogen cooling degraded the deformability of the welded materials such that the width of interfacial cracks increased with increasing cooling time. The grain size of the stirred zone (SZ) and the heat-affected zone (HAZ) of the C-FSSW-welded joints decreased, whereas that of the thermomechanically affected zone (TMAZ) increased with increasing cooling time. The maximum tensile shear load of the C-FSSW-welded joints welded with a cooling time of 5 or 7 s was larger than that of the friction stir spot welding (FSSW)-welded joint, and the tensile shear load decreased with increasing cooling time. The microhardness of the C-FSSW-welded joints was greater than that of the FSSW-welded joint. Moreover, the microhardness of the SZ and the HAZ of the C-FSSW-welded joints increased, whereas that of the TMAZ decreased, with increasing cooling time.

Effect of alternating voltage treatment on corrosion resistance of AZ91D magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Liu, X. [Corrosion and Protection Laboratory, Key Laboratory of Superlight Materials and Surface Technology (Harbin Engineering University), Ministry of Education, Harbin (China); Zhang, T.; Shao, Y.; Meng, G.; Wang, F. [Corrosion and Protection Laboratory, Key Laboratory of Superlight Materials and Surface Technology (Harbin Engineering University), Ministry of Education, Harbin (China); State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang (China)

2012-06-15

AZ91D magnesium alloy was treated by the alternating voltage (AV) treatment technique. The optimal AV-treatment parameters of the alloy were determined by orthogonal experiments. Polarization curve, electrochemical impedance spectroscopy (EIS), and scanning electrochemical microscopy (SECM) were used to understand the effect of AV-treatment on the corrosion resistance of the alloy. AFM, contact angle, and XPS were employed to investigate further the influence of AV-treatment on the properties of the surface film formed on the alloy after AV-treatment. The results showed that a uniform and stable film was formed and the corrosion resistance of AZ91D magnesium alloy was significantly improved after AV-treatment. This was caused by the noticeable change of the chemical structure and semi-conducting properties of the surface film after AV-treatment. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Ovate pontics: Phoenixing the gingival contour

Directory of Open Access Journals (Sweden)

Medha Vivek Bhuskute

2017-01-01

Full Text Available In today's busy world, most patients do not have time for long, drawn-out dental treatment. The time span between extraction and healing after loss of tooth in the anterior esthetic zone can be esthetically and psychologically devastating on the part of the patient. Especially, when a maxillary anterior tooth must be extracted and replaced, immediate tooth replacement with an ovate pontic on a provisional bridge is a good alternative. Ovate pontic helps in preservation of the interdental papilla, which in turn preserves the natural gingival contour that would have otherwise been lost after extraction. An immediate tooth replacement using ovate pontic not only eliminates the psychologically disturbing partially edentulous phase but also results in a much more esthetically pleasing replacement of tooth that is both hygienic and natural in appearance. Another added advantage of the use of ovate pontic is that it rules out the dissatisfaction resulting from an unesthetic ridge lap pontic placed directly over edentulous ridge. Just like the long-lived bird “Phoenix,” arising out of its own ashes, the ovate pontic creates an illusion that the pontic is emerging from the gingiva, even after tooth loss. This case report discusses how an integrated approach of fabricating heat cure provisional bridge with ovate pontics before extractions, benefitted a young patient in whom fractured anterior teeth were proposed for extraction.

Characterization of hydrogen peroxide-resistant Acinetobacter species isolated during the Mars Phoenix spacecraft assembly.

Science.gov (United States)

Derecho, I; McCoy, K B; Vaishampayan, P; Venkateswaran, K; Mogul, R

2014-10-01

The microbiological inventory of spacecraft and the associated assembly facility surfaces represent the primary pool of forward contaminants that may impact the integrity of life-detection missions. Herein, we report on the characterization of several strains of hydrogen peroxide-resistant Acinetobacter, which were isolated during the Mars Phoenix lander assembly. All Phoenix-associated Acinetobacter strains possessed very high catalase specific activities, and the specific strain, A. gyllenbergii 2P01AA, displayed a survival against hydrogen peroxide (no loss in 100 mM H2O2 for 1 h) that is perhaps the highest known among Gram-negative and non-spore-forming bacteria. Proteomic characterizations reveal a survival mechanism inclusive of proteins coupled to peroxide degradation (catalase and alkyl hydroperoxide reductase), energy/redox management (dihydrolipoamide dehydrogenase), protein synthesis/folding (EF-G, EF-Ts, peptidyl-tRNA hydrolase, DnaK), membrane functions (OmpA-like protein and ABC transporter-related protein), and nucleotide metabolism (HIT family hydrolase). Together, these survivability and biochemical parameters support the hypothesis that oxidative tolerance and the related biochemical features are the measurable phenotypes or outcomes for microbial survival in the spacecraft assembly facilities, where the low-humidity (desiccation) and clean (low-nutrient) conditions may serve as selective pressures. Hence, the spacecraft-associated Acinetobacter, due to the conferred oxidative tolerances, may ultimately hinder efforts to reduce spacecraft bioburden when using chemical sterilants, thus suggesting that non-spore-forming bacteria may need to be included in the bioburden accounting for future life-detection missions.

The Phoenix TECP Relative Humidity Sensor: Revised Results

Science.gov (United States)

Zent, Aaron

2014-01-01

The original calibration function of the RH sensor on the Phoenix mission's Thermal and Electrical Conductivity Sensor (TECP), has been revised to correct the erroneously-published original calibration equation, to demonstrate the value of this unique data set, and to improve characterization of H2O exchange between the martian regolith and atmosphere. TECP returned two data streams, the temperature of the electronics analog board (Tb) and the digital 12-bit output of the RH sensor (DN), both of which are required to uniquely specify the H2O abundance. Because the original flight instrument calibration was performed against a pair of hygrometers that measured frost point (Tf), the revised calibration equation is also cast in terms of frost point. The choice of functional form for the calibration function is minimally constrained. A series of profiles across the calibration data cloud at constant DN and Tb does not reveal any evidence of a complex functional form. Therefore, a series of polynomials in both DN and Tb was investigated, along with several non-linear functions of DN and Tb.

Metallurgical bond between magnesium AZ91 alloy and aluminium plasma sprayed coatings

Czech Academy of Sciences Publication Activity Database

Kubatík, Tomáš František; Pala, Zdeněk; Neufuss, Karel; Vilémová, Monika; Mušálek, Radek; Stoulil, J.; Slepička, P.; Chráska, Tomáš

2015-01-01

Roč. 282, November (2015), s. 163-170 ISSN 0257-8972 R&D Projects: GA ČR(CZ) GP14-31538P Institutional support: RVO:61389021 Keywords : Plasma spraying * AZ91 magnesium alloy * Aluminium * Metallurgical bond * X-ray diffraction Subject RIV: JK - Corrosion ; Surface Treatment of Materials Impact factor: 2.139, year: 2015 http://www.sciencedirect.com/science/article/pii/S0257897215303297

Enzymatic production of sterculic acid from the novel Phoenix tree seed oil: Optimization and kinetic study

International Nuclear Information System (INIS)

Hou, X.; Sun, S.

2017-01-01

Phoenix tree (Firmiana simplex) seed oil is a novel oil which is rich in sterculic acid. Sterculic acid, a cyclopropene fatty acid, can be used as the inhibitor of the stearoyl-CoA desaturase system and mammary carcinomas growth. In this work, Lipozyme TLIM-catalyzed hydrolysis of the novel Phoenix tree seed oil was used to prepare sterculic acid. High temperature GC-FID and the degree of hydrolysis (DH) were used to monitor the reaction progress. Effects of reaction variables on the hydrolysis were evaluated and optimized using response surface methodology. Results showed that sterculic acid can be successfully prepared from the novel seed oil, and the effect of reaction variables on the hydrolysis decreased in the order of reaction time > enzyme load > temperature. A high yield of fatty acids (DH, 98.2±0.8%) can be obtained under optimized conditions (45 ºC, mass ratio of water to oil 10:1, enzyme load 10%, and 18 h). The Arrhenius equation for the hydrolysis was LnV0 = 9.12 − 4721/T. The activation energy was 39.25KJ/mol. The kinetic values for Vmax, K/m were 0.232mol/(L∙min) and 0.084 mol/L, respectively. [es

Technologies using accelerator-driven targets under development at BNL

International Nuclear Information System (INIS)

Van Tuyle, G.J.

1994-01-01

Recent development work conducted at Brookhaven National Laboratory on technologies which use particle accelerator-driven targets is summarized. These efforts include development of the Spallation-Induced Lithium Conversion (SILC) Target for the Accelerator Production of Tritium (APT), the Accelerator-Driven Assembly for Plutonium Transformation (ADAPT) Target for the Accelerator-Based Conversion (ABC) of excess weapons plutonium. The PHOENIX Concept for the accelerator-driven transmutation of minor actinides and fission products from the waste stream of commercial nuclear power plants, and other potential applications

Flow mechanisms in creep of a short-fibre AZ91 alloy-based composite

Czech Academy of Sciences Publication Activity Database

Pahutová, Marie; Sklenička, Václav; Kuchařová, Květa; Svoboda, Milan; Langdon, T. G.

43 2005, č. 1 (2005), s. 34-44 ISSN 0023-432X R&D Projects: GA ČR(CZ) GA106/03/0901 Institutional research plan: CEZ:AV0Z20410507 Keywords : AZ91 magnesium alloy * metal matrix composite * short fibre reinforcement Subject RIV: JG - Metallurgy Impact factor: 0.973, year: 2005

Fault-tolerant epoxy-silane coating for corrosion protection of magnesium alloy AZ31

NARCIS (Netherlands)

Lamaka, S.V.; Xue, H.B.; Meis, N.N.A.H.; Esteves, A.C.C.; Ferreira, M.G.S.

2015-01-01

In this work, a hybrid epoxy-silane coating was developed for corrosion protection of magnesium alloy AZ31. The average thickness of the film produced by dip-coating procedure was 14 µm. The adhesion strength of the epoxy-silane coating to the Mg substrate was evaluated by pull-off tests and was

Thermal Microstructural Stability of AZ31 Magnesium after Severe Plastic Deformation

Energy Technology Data Exchange (ETDEWEB)

Young, John P.; Askari, Hesam A.; Hovanski, Yuri; Heiden, Michael J.; Field, David P.

2015-03-01

Both equal channel angular pressing and friction stir processing have the ability to refine the grain size of twin roll cast AZ31 magnesium and potentially improve its superplastic properties. This work used isochronal and isothermal heat treatments to investigate the microstructural stability of twin roll cast, equal channel angular pressed and friction stir processed AZ31 magnesium. For both heat treatment conditions, it was found that the twin roll casted and equal channel angular pressed materials were more stable than the friction stir processed material. Calculations of the grain growth kinetics showed that severe plastic deformation processing decreased the activation energy for grain boundary motion with the equal channel angular pressed material having the greatest Q value of the severely plastically deformed materials and that increasing the tool travel speed of the friction stir processed material improved microstructural stability. The Hollomon-Jaffe parameter was found to be an accurate means of identifying the annealing conditions that will result in substantial grain growth and loss of potential superplastic properties in the severely plastically deformed materials. In addition, Humphreys’s model of cellular microstructural stability accurately predicted the relative microstructural stability of the severely plastically deformed materials and with some modification, closely predicted the maximum grain size ratio achieved by the severely plastically deformed materials.

Slow speed object detection for haul trucks

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-09-15

Caterpillar integrates radar technology with its current camera based system. Caterpillar has developed the Integrated Object Detection System, a slow speed object detection system for mining haul trucks. Object detection is a system that aids the truck operator's awareness of their surroundings. The system consists of a color touch screen display along with medium- and short-range radar as well as cameras, harnesses and mounting hardware. It is integrated into the truck's Work Area Vision System (WAVS). After field testing in 2007, system commercialization began in 2008. Prototype systems are in operation in Australia, Utah and Arizona and the Integrated Object Detection System will be available in the fourth quarter of 2009 and on production trucks 785C, 789C, 793D and 797B. The article is adapted from a presentation by Mark Richards of Caterpillar to the Haulage & Loading 2009 conference, May, held in Phoenix, AZ. 1 fig., 5 photos.

En híbrida mezcolanza: Exile and Cultural Anxiety in Alirio Díaz Guerra’s Lucas Guevara

Directory of Open Access Journals (Sweden)

Jeffrey Browitt

2005-03-01

Full Text Available The novel Lucas Guevara, written by the Colombian exile, Alirio Díaz Guerra, was first published in New York in 1914. It is considered to be the earliest novel about Latin American immigration to the United States written in Spanish. This fact alone merits its study. A second edition was published in 2001 along with a critical-biographical introduction, which presents the novel as the precursor of a developing genre of Hispanic immigrant literature centred on the naïve Latin American migrant who arrives in the United States inspired by the opportunities which the metropolis supposedly affords, but who nevertheless suffers a series of misfortunes because of the inability to adapt to the new culture. On the level of overt content, the novel is a lachrymose, stereotypical and conventional denunciation of the supposed evils of an amoral US society and the libertine and materialistic values underpinning it. But on a much deeper level, a picture emerges of Díaz Guerra himself as a displaced, disenchanted intellectual exile who suffers (or has suffered an acute cultural and class anxiety in the transition from a patrician Arcadia to the heart of capitalist, industrial modernity. Through a reading of the narrative voice, and by extension the implied author, we witness his difficult coming to terms with a highly-charged New York society (in comparison to his homeland, not only because of the sexual liberation brought on by secular modernization, but also because of the close proximity of volatile, eroticised bodies on the over-crowded Lower East Side of New York, the scene of the novel and Díaz Guerra’s point of entry into the United States. The novel also provides an occasion to contrast how Díaz Guerra deals with the condition of exile, in contrast to that most emblematic of Latin American political refugees, José Martí.

A Study of the Physiological Factors Affecting the Nature of the Adult Learner in the Phoenix Air National Guard.

Science.gov (United States)

Torbert, James Brison

An investigation reviewed current literature in the field of physiological factors affecting the adult learning environment. These findings were compared to the academic learning environment at the Phoenix Air National Guard. The end product was a set of recommendations for management to implement in order to improve the learning climate for the…

Corrosion behavior of friction stir welded AZ31B Mg alloy - Al6063 alloy joint

Directory of Open Access Journals (Sweden)

B. Ratna Sunil

2016-12-01

Full Text Available In the present work, AZ31B Mg alloy and Al6063 alloy-rolled sheets were successfully joined by friction stir welding. Microstructural studies revealed a sound joint with good mechanical mixing of both the alloys at the nugget zone. Corrosion performance of the joint was assessed by immersing in 3.5% NaCl solution for different intervals of time and the corrosion rate was calculated. The joint has undergone severe corrosion attack compared with both the base materials (AZ31B and Al6063 alloys. The predominant corrosion mechanism behind the high corrosion rate of the joint was found to be high galvanic corrosion. From the results, it can be suggested that the severe corrosion of dissimilar Mg–Al joints must be considered as a valid input while designing structures intended to work in corroding environment.

Mega drought in the Colorado River Basin, water supply, and adaptive scenario planning for the Phoenix Metropolitan Area; simulations using WaterSim 5.

Science.gov (United States)

Sampson, D. A.

2015-12-01

The Decision Center for a Desert City (DCDC), a boundary organization, bridges science and policy (to foster knowledge-based decision making); we study how decisions are made in the face of uncertainty. Our water policy and management model for the Phoenix Metropolitan Area (hereafter "Phoenix"), termed WaterSim, represents one such bridging mechanism. We evaluated the effect of varying the length of drought on water availability for Phoenix. We examined droughts (starting in 2000) lasting 15, 25, and 50 years. We picked a 60-year window of runoff estimates from the paleo reconstruction data for the Colorado River (CO) (1121 through 1180 A.D.), and the two local rivers (1391 through 1450 A.D.), and assumed that the proportional difference in median flow between these periods and the long-term record represented an estimate of potential drought reductions on river flows. This resulted in a 12%, and 19% reduction in flows for the CO River and the Salt-Verde (SV) Rivers, respectively. WaterSim uses 30-year trace periods from the historical flow records to simulate river flow for future projections. We used each 30-year trace from the historical record (1906 to present, CO River; 1945 to present SV Rivers) , and default settings, to simulate 60 year projections of Lake Mead elevation and the accompanying Colorado River water shortages to Phoenix. Overall, elevations for Lake Mead fell below the 1st shortage sharing tier (1075 ft) in 83% of the simulations; 74% of the simulations fell below the 2nd tier (1050 ft), and 64% fell below the 3rd (1025 ft). Length of drought, however, determined the shortage tiers met. Median elevations for droughts ending in 2015, 2025, and 2050 were 1036, 1019, and 967 feet msl, respectively. We present the plausible water futures with adaptive anticipatory scenario planning for the projected reductions in surface water availability to demonstrate decision points for water conservation measures to effectively manage shortage conditions.

Effect of antimony, bismuth and calcium addition on corrosion and electrochemical behaviour of AZ91 magnesium alloy

International Nuclear Information System (INIS)

Zhou Wei; Aung, Naing Naing; Sun Yangshan

2009-01-01

This study investigated the effect of antimony, bismuth and calcium addition on the corrosion and electrochemical behaviour of AZ91 magnesium alloy in 3.5% NaCl solution. Techniques including constant immersion, electrochemical potentiodynamic polarisation, scanning electron microscopy (SEM), energy dispersed spectroscopy (EDS) and X-ray diffraction (XRD) were used to characterise electrochemical and corrosion properties and surface topography. It was found that corrosion attack occurred preferentially on Mg 3 Bi 2 and Mg 3 Sb 2 particles while Mg 17 Al 8 Ca 0.5 and Mg 2 Ca phases showed no detrimental effect on corrosion. Combined addition of small amounts of bismuth and antimony to the AZ91 alloy resulted in significant increase in corrosion rate

Investigation on the Effect of Pulsed Energy on Strength of Fillet Lap Laser Welded AZ31B Magnesium Alloys

Science.gov (United States)

Salleh, M. N. M.; Ishak, M.; Aiman, M. H.; Idris, S. R. A.; Romlay, F. R. M.

2017-09-01

AZ31B magnesium alloy have been hugely applied in the aerospace, automotive, and electronic industries. However, welding thin sheet AZ31B was challenging due to its properties which is easily to evaporated especially using conventional fusion welding method such as metal inert gas (MIG). Laser could be applied to weld this metal since it produces lower heat input. The application of fiber laser welding has been widely since this type of laser could produce better welding product especially in the automotive sectors. Low power fiber laser was used to weld this non-ferrous metal where pulse wave (PW) mode was used. Double fillet lap joint was applied to weld as thin as 0.6 mm thick of AZ31B and the effect of pulsed energy on the strength was studied. Bond width, throat length, and penetration depth also was studied related to the pulsed energy which effecting the joint. Higher pulsed energy contributes to the higher fracture load with angle of irradiation lower than 3 °

IMPACT OF DEPTH OF CUT ON CHIP FORMATION IN AZ91HP MAGNESIUM ALLOY MILLING WITH TOOLS OF VARYING CUTTING EDGE GEOMETRY

Directory of Open Access Journals (Sweden)

Olga Gziut

2015-05-01

Full Text Available Safety of Mg milling processes can be expressed by means of the form and the number of fractions of chips formed during milling. This paper presents the state of the art of magnesium alloys milling technology in the aspect of chip fragmentation. Furthermore, the impact of the depth of cut ap and the rake angle γ on the number of chip fractions was analysed in the study. These were conducted on AZ91HP magnesium cast alloy and milling was performed with carbide tools of varying rake angle values (γ = 5º and γ = 30º. It was observed that less intense chip fragmentation occurs with decreasing depth of cut ap. The number of chip fractions was lower at the tool rake angle of γ = 30º. The test results were formulated as technological recommendations according to the number of generated chip fractions.

Hydroxyapatite coating on AZ91 magnesium alloy via sol-gel method

OpenAIRE

Albayrak, Sevda; Çinici, Hanifi; Çalın, Recep; Cömert, Canser

2018-01-01

Producinga material lighter than available biomaterials, having corrosion-resistance tobiological attacks and histocompatible similar to the bone structure in orderto use in biomedical applications is the purpose of this study. Lightness isextremely important in biomedical applications because stainless steel and manyof the similar heavy metallic alloys can lead to infection by causing harm totissues around the implant when it is used in the body. Although the lightnessof AZ91 Mg alloy is an ...

Constituyentes volátiles del mango de azúcar

OpenAIRE

Bautista., Edgar; Duque, Carmenza; Torres, Rafael

2010-01-01

Empleando Extracción de Volátiles por Espacio de Cabeza Dinámico y Extracción Líquido-Líquido, se estudió el aroma del mango de azúcar (Mangifera indica L), variedad nativa Colombiana apreciada por su exquisito aroma y sabor. Estos dos métodos complementarios permifieron la identificación, por Cromatografía de Gases de Alta resolución y Cromatografía de Gases de Alta Resolución - Espectrometría de Masas, de 52 coinponentes, entre los cuales sobresalieron como mayoritarios el 3-careno, el b...

Effects of filter materials on microstructure and mechanical properties of AZ91

Directory of Open Access Journals (Sweden)

Wu Guohua

2010-11-01

Full Text Available The present investigation studied the effects of different kinds of ceramic foam filters (CFF incorporating gas bubbling on the microstructure and mechanical properties of virgin AZ91 alloys, and the reactions between filters and Mg melt during filtration. The results show that the purification process of CFF incorporating gas bubbling process can obviously improve the Rm and A of AZ91 alloy, especially the A. Amongst the selected four kinds of CFF, the MgO filter is the most suitable for filtrating Mg melt, and the filtration effective sequence of four kinds of filtrating materials is as follows: MgO>Al2O3>ZrO2>SiC. With MgO filter incorporating gas bubbling treatment under Ar flow rate of 2 L/min and temperature of 730 °C, the ultimate tensile strength Rm and elongation A can be improved greatly from 175.3 MPa and 2.74% to 195.4 MPa and 4.54%, respectively. No inclusions are found on the fracture surface of the sample filtrated by MgO ceramic foam filter, and the fracture mode is quasi-cleavage crack.

Microstructure control during twin roll casting of an AZ31 magnesium alloy

International Nuclear Information System (INIS)

Huang, Y; Bayandorian, I; Fan, Z

2012-01-01

The existing twin roll casting technique for magnesium alloys suffers heterogeneity in both microstructure and chemistry and downstream processing is required to improve the strip quality, resulting in cost rise. In the present work, twin roll casting was carried out using an AZ31 magnesium alloy, with the application of intensive shearing melt conditioning prior to casting. The effect of process parameters such as pouring temperature and casting speed on microstructure control during casting and subsequent downstream processing was studied. Experimental results showed that the melt conditioning treatment allowed the production of AZ31 strips with uniform and refined microstructure free of centreline segregations. It was also shown that an optimized combination of pouring temperature and casting speed, in conjunction with a strip thickness control operation, resulted in uniformly distributed stored energies due to enhanced plastic deformation, which promoted recrystallization during casting and subsequent heat treatment. Strips prepared by twin roll casting and homogenization developed similar microstructural features to those prepared by twin roll casting followed by lengthy downstream processing by homogenization, hot rolling and annealing and displayed a weaker basal texture, exhibiting a potentially better formability.

Mechanical properties of AZ31 alloy processed by a green metallurgy route

International Nuclear Information System (INIS)

D'Enrico, F.; Garces, G.; Hofer, M.; Kim, S. K.; Perez, P.; Cabeza, S.; Adeva, P.

2013-01-01

Recently it has been proved that molding of defect-free components of various commercial alloys of magnesium can be carried out successfully when small amounts of CaO are added to the melt, making unnecessary the use of SF 6 coverage. In the case of AZ alloys, this process also remarkably improves their mechanical properties not only by the greater cleaning of alloys but also by the formation of CaAl 2 phase. This work, part of the Green project Metallurgy (http://www.green-metallurgy.eu) funded by the European Union (LIFE+2009), studies the influence of different CaO additions on the microstructure and mechanical properties of AZ31 Eco-Mg alloy. The alloy was processed by a conventional route involving extrusion of as-cast rods as well as by a powder metallurgy route (PM) using chips as starting material. The objective was to analyze the viability of recycling machining chips to manufacture components for the automobile industry and transportation in general, because of its low cost and environmental impact. It has been demonstrated that alloys processed from chips exhibit the highest tensile stress values, close to 320 MPa. (Author)

Desarrollo de las pequeñas industrias rurales de la caña de azúcar en iberoamerica: Melaza, Panela y Azúcar Moreno

OpenAIRE

Da Silva, Fabio César; Cesar, Marco; Hernández Díaz-Ambrona, Carlos Gregorio

2010-01-01

Los niveles de producción de azúcar en los últimos años crecen a un ritmo semejante al crecimiento poblacional. El fabricante debe estar atento a las características de calidad del producto que su mercado o comprador/consumidor exige y la facilidad de transporte al centro consumidor. La legislación debe especificar los requisitos mínimos pero el fabricante debe tener como desafío ofrecer un producto de calidad y reducir los riesgos ambientales en sus cultivos en función de la aptitud de la...

A New Factor in American Destiny: Visions of Porfirio Díaz and the Politics of “Logical Paternalism”

Directory of Open Access Journals (Sweden)

Jason Ruiz

2011-12-01

Full Text Available This essay interprets American representations of dictator Porfirio Díaz in relation to the “economic conquest” of Mexico that took place during his long rule (1876–1911, a period known as the “Porfiriato,” in which Americans invested more than $1 billion. No single person inspired as much attention from travelers, reporters, and photographers during the late nineteenth and early twentieth centuries as Díaz, and their visions of the President helped to shape perceptions of Mexico as a desirable field in which to expand US capitalism and influence. Travelers clamored to meet him and his sophisticated young wife, and their travelogues were rich with descriptions of such encounters. Reporters, dazzled by the rapid transformation of Mexico during his 35-year rule, described Díaz in such terms as “the Mexican Wizard” and “the maker of modern Mexico” until the very end of his regime. Photographers, working in a relatively new medium, amassed a huge body of works devoted to the dictator; even at an advanced age late in his rule, the President’s image adorned postcards and commemorative cartes-de-visite that posited him in heroic and hypermasculine terms (not unlike those of his US counterpart, Theodore Roosevelt. Ultimately, this essay argues that representations like these reflected American desires for a Mexican body politic that was amenable to economic and social transformation under the inextricable banners of “progress” and US capitalism. Prevailing images of Díaz and his family suggested that Mexico was as friendly to foreign investors as it was to foreign visitors.

Laser surface forming of AlCoCrCuFeNi particle reinforced AZ91D matrix composites

Science.gov (United States)

Meng, Guanghui; Yue, T. M.; Lin, Xin; Yang, Haiou; Xie, Hui; Ding, Xu

2015-07-01

Traditionally, the laser melt injection (LMI) technique can only be used for forming ceramic particles reinforced metal matrix composites (MMCs) for enhancing surface properties of lightweight engineering materials. In this research, the LMI method was employed to form metal particles reinforced MMCs on AZ91D instead. This was viable because of the unique properties of the AlCoCrCuFeNi high-entropy alloy (HEA) metal particles used. The large difference in melting point between the HEA and the substrate material (AZ91D), and the limited reaction and the lack of fusion between the HEA and Mg have made it possible that a metal particles reinforced AZ91D composite material was produced. The reason of limited reaction was considered mainly due to the relatively high mixing enthalpy between the HEA constituent elements and Mg. Although there was some melting occurred at the particles surface with some solute segregation found in the vicinity close to the surface, intermetallic compounds were not observed. With regard to the wear resistance of the MMCs, it was found that when the volume fraction of the reinforcement phase, i.e. the HEA particles, reached about 0.4, the wear volume loss of the coating was only one-seventh of that of the substrate material.

Corrosion behaviors in physiological solution of cerium conversion coatings on AZ31 magnesium alloy

International Nuclear Information System (INIS)

Cui Xiufang; Yang Yuyun; Liu Erbao; Jin Guo; Zhong Jinggao; Li Qingfen

2011-01-01

In this paper, a non-toxic Ce-based conversion coating was obtained on the surface of bio-medical AZ31 magnesium alloys. The micro-morphology of the coating prepared with optimal technical parameters and immersed in physiological solution (Hank's solution) in different time was observed by scanning electron microscopy (SEM), composition of the cerium conversion coating and corrosion products in Hank's solution were characterized by X-ray photoelectron spectroscopy (XPS) and energy dispersive spectroscopy (EDS), respectively. In addition, the corrosion property in Hank's solution was studied by electrochemical experiment and immersion test. The results show that the dense Ce-based conversion coating is obtained on the surface of AZ31 magnesium alloys in optimal technical parameters and the conversion coating consists of a mass of trivalent and tetravalent cerium oxides. The cerium conversion coating can provide obvious protection of magnesium alloys and can effectively reduce the degradation speed in Hank's solution. Also the degradation products have little influence on human body.

High speed cutting of AZ31 magnesium alloy

Directory of Open Access Journals (Sweden)

Liwei Lu

2016-06-01

Full Text Available Using LBR-370 numerical control lathe, high speed cutting was applied to AZ31 magnesium alloy. The influence of cutting parameters on microstructure, surface roughness and machining hardening were investigated by using the methods of single factor and orthogonal experiment. The results show that the cutting parameters have an important effect on microstructure, surface roughness and machine hardening. The depth of stress layer, roughness and hardening present a declining tendency with the increase of the cutting speed and also increase with the augment of the cutting depth and feed rate. Moreover, we established a prediction model of the roughness, which has an important guidance on actual machining process of magnesium alloy.

The surface chemistry of 3-mercaptopropyltrimethoxysilane films deposited on magnesium alloy AZ91

International Nuclear Information System (INIS)

Scott, A.; Gray-Munro, J.E.

2009-01-01

Magnesium and its alloys have desirable physical and mechanical properties for a number of applications. Unfortunately, these materials are highly susceptible to corrosion, particularly in the presence of aqueous solutions. The purpose of this study is to develop a uniform, non-toxic surface treatment to enhance the corrosion resistance of magnesium alloys. This paper reports the influence of the coating bath parameters and alloy microstructure on the deposition of 3-mercaptopropyltrimethoxysilane (MPTS) coatings on magnesium alloy AZ91. The surface chemistry at the magnesium/MPTS interface has also been explored. The results indicate that the deposition of MPTS onto AZ91 was influenced by both the pH and MPTS concentration in the coating bath. Furthermore, scanning electron microscopy results showed that the MPTS film deposited uniformly on all phases of the magnesium alloy surface. X-ray photoelectron spectroscopy studies revealed that at the magnesium/MPTS interface, the molecules bond to the surface through the thiol group in an acid-base interaction with the Mg(OH) 2 layer, whereas in the bulk of the film, the molecules are randomly oriented.

Microstructural characterization and finite element modeling of AZ31 magnesium alloys welded joints

Directory of Open Access Journals (Sweden)

José A. Segarra

2018-03-01

Full Text Available In this article, it has been studied how the microstructure of AZ31 magnesium alloy can be affected by the thermic cycles produced by welding processes, trying to modeling by element finite software the thermic cycles in this material. The AZ31 samples tested were welded using Gas Tugsten Arc Welding (GTAW and different filler materials. For this investigation, optic microscopy, scanning electronic microscopy, and finite elements method software has been used. This work indicates in one hand that in this type of alloys the microconstituyentes are Al-Mn o Al-Mn-Mg compounds, the presence of β-phase cannot be found at room temperature in this research at room, on the other hand the obtained simulation models indicate that the recrystallization takes place in the areas which reach maximum temperatures around 550 °C, this value is also the limit of the dissolution area for the Al-Mn o Al-Mn-Mg precipitated particles which are very likely to act as inhibitors of the corrosion in NaCl electrolytes.

A prelanding assessment of the ice table depth and ground ice characteristics in Martian permafrost at the Phoenix landing site

Science.gov (United States)

Mellon, M.T.; Boynton, W.V.; Feldman, W.C.; Arvidson, R. E.; Titus, Joshua T.N.; Bandfield, L.; Putzig, N.E.; Sizemore, H.G.

2009-01-01

We review multiple estimates of the ice table depth at potential Phoenix landing sites and consider the possible state and distribution of subsurface ice. A two-layer model of ice-rich material overlain by ice-free material is consistent with both the observational and theoretical lines of evidence. Results indicate ground ice to be shallow and ubiquitous, 2-6 cm below the surface. Undulations in the ice table depth are expected because of the thermodynamic effects of rocks, slopes, and soil variations on the scale of the Phoenix Lander and within the digging area, which can be advantageous for analysis of both dry surficial soils and buried ice-rich materials. The ground ice at the ice table to be sampled by the Phoenix Lander is expected to be geologically young because of recent climate oscillations. However, estimates of the ratio of soil to ice in the ice-rich subsurface layer suggest that that the ice content exceeds the available pore space, which is difficult to reconcile with existing ground ice stability and dynamics models. These high concentrations of ice may be the result of either the burial of surface snow during times of higher obliquity, initially high-porosity soils, or the migration of water along thin films. Measurement of the D/H ratio within the ice at the ice table and of the soil-to-ice ratio, as well as imaging ice-soil textures, will help determine if the ice is indeed young and if the models of the effects of climate change on the ground ice are reasonable. Copyright 2008 by the American Geophysical Union.

Analysis of metallic traces from the biodegradation of endomedullary AZ31 alloy temporary implants in rat organs after long implantation times.

Science.gov (United States)

Bodelón, O G; Iglesias, C; Garrido, J; Clemente, C; Garcia-Alonso, M C; Escudero, M L

2015-08-04

AZ31 alloy has been tested as a biodegradable material in the form of endomedullary implants in female Wistar rat femurs. In order to evaluate the accumulation of potentially toxic elements from the biodegradation of the implant, magnesium (Mg), aluminium (Al), zinc (Zn), manganese (Mn) and fluorine (F) levels have been measured in different organs such as kidneys, liver, lungs, spleen and brain. Several factors that may influence accumulation have been taken into account: how long the implant has been in place, whether or not the bone is fractured, and the presence of an MgF2 protective coating on the implant. The main conclusions and the clinical relevance of the study have been that AZ31 endomedullary implants have a degradation rate of about 60% after 13 months, which is fully compatible with fracture consolidation. Neither bone fracture nor an MgF2 coating seems to influence the accumulation of trace elements in the studied organs. Aluminium is the only alloying element in this study that requires special attention. The increase in Al recovered from the sampled organs represents 3.95% of the amount contained in the AZ31 implant. Al accumulates in a statistically significant way in all the organs except the brain. All of this suggests that in long-term tests AZ31 may be a suitable material for osteosynthesis.

78 FR 23135 - Safety Zone; Blue Water Resort & Casino West Coast Nationals; Parker, AZ

Science.gov (United States)

2013-04-18

...-AA00 Safety Zone; Blue Water Resort & Casino West Coast Nationals; Parker, AZ AGENCY: Coast Guard, DHS... Water Resort & Casino West Coast Nationals. This temporary safety zone is necessary to provide for the....). RPM Racing Enterprises is sponsoring the Blue Water Resort & Casino West Coast Nationals, which is...

75 FR 5115 - Temporary Concession Contract for Lake Mead National Recreation Area, AZ/NV

Science.gov (United States)

2010-02-01

... National Recreation Area, AZ/NV AGENCY: National Park Service, Department of the Interior. ACTION: Notice of intention to award temporary concession contract for Lake Mead National Recreation Area. SUMMARY: Pursuant to 36 CFR 51.24, public notice is hereby given that the National Park Service intends to award a...

Comparison of Electrochemical Methods for the Evaluation of Cast AZ91 Magnesium Alloy

Czech Academy of Sciences Publication Activity Database

Tkacz, J.; Minda, J.; Fintová, Stanislava; Wasserbauer, J.

2016-01-01

Roč. 9, č. 11 (2016), č. článku 925. ISSN 1996-1944 Institutional support: RVO:68081723 Keywords : AZ91 magnesium alloy * cathodic polarization curve * anodic polarization curve * linear polarization curve Subject RIV: JK - Corrosion ; Surface Treatment of Materials Impact factor: 2.654, year: 2016 http://www.mdpi.com/1996-1944/9/11/925

AZ-101 Mixer Pump Demonstration and Tests Data Management Analysis Plan

Energy Technology Data Exchange (ETDEWEB)

DOUGLAS, D.G.

2000-02-22

This document provides a plan for the analysis of the data collected during the AZ-101 Mixer Pump Demonstration and Tests. This document was prepared after a review of the AZ-101 Mixer Pump Test Plan (Revision 4) [1] and other materials. The plan emphasizes a structured and well-ordered approach towards handling and examining the data. This plan presumes that the data will be collected and organized into a unified body of data, well annotated and bearing the date and time of each record. The analysis of this data will follow a methodical series of steps that are focused on well-defined objectives. Section 2 of this plan describes how the data analysis will proceed from the real-time monitoring of some of the key sensor data to the final analysis of the three-dimensional distribution of suspended solids. This section also identifies the various sensors or sensor systems and associates them with the various functions they serve during the test program. Section 3 provides an overview of the objectives of the AZ-101 test program and describes the data that will be analyzed to support that test. The objectives are: (1) to demonstrate that the mixer pumps can be operated within the operating requirements; (2) to demonstrate that the mixer pumps can mobilize the sludge in sufficient quantities to provide feed to the private contractor facility, and (3) to determine if the in-tank instrumentation is sufficient to monitor sludge mobilization and mixer pump operation. Section 3 also describes the interim analysis that organizes the data during the test, so the analysis can be more readily accomplished. Section 4 describes the spatial orientation of the various sensors in the tank. This section is useful in visualizing the relationship of the Sensors in terms of their location in the tank and how the data from these sensors may be related to the data from other sensors. Section 5 provides a summary of the various analyses that will be performed on the data during the test

AZ-101 Mixer Pump Demonstration and Tests: Data Management (Analysis) Plan

International Nuclear Information System (INIS)

DOUGLAS, D.G.

2000-01-01

This document provides a plan for the analysis of the data collected during the AZ-101 Mixer Pump Demonstration and Tests. This document was prepared after a review of the AZ-101 Mixer Pump Test Plan (Revision 4) [1] and other materials. The plan emphasizes a structured and well-ordered approach towards handling and examining the data. This plan presumes that the data will be collected and organized into a unified body of data, well annotated and bearing the date and time of each record. The analysis of this data will follow a methodical series of steps that are focused on well-defined objectives. Section 2 of this plan describes how the data analysis will proceed from the real-time monitoring of some of the key sensor data to the final analysis of the three-dimensional distribution of suspended solids. This section also identifies the various sensors or sensor systems and associates them with the various functions they serve during the test program. Section 3 provides an overview of the objectives of the AZ-101 test program and describes the data that will be analyzed to support that test. The objectives are: (1) to demonstrate that the mixer pumps can be operated within the operating requirements; (2) to demonstrate that the mixer pumps can mobilize the sludge in sufficient quantities to provide feed to the private contractor facility, and (3) to determine if the in-tank instrumentation is sufficient to monitor sludge mobilization and mixer pump operation. Section 3 also describes the interim analysis that organizes the data during the test, so the analysis can be more readily accomplished. Section 4 describes the spatial orientation of the various sensors in the tank. This section is useful in visualizing the relationship of the Sensors in terms of their location in the tank and how the data from these sensors may be related to the data from other sensors. Section 5 provides a summary of the various analyses that will be performed on the data during the test

Effect of the Strain Rate on the Tensile Properties of the AZ31 Magnesium Alloy

International Nuclear Information System (INIS)

Jeong, Seunghun; Park, Jiyoun; Choi, Ildong; Park, Sung Hyuk

2013-01-01

The effect of the strain rate at a range of 10‒4 ⁓ 3 × 10"2s"-1 on the tensile characteristics of a rolled AZ31 magnesium alloy was studied. The normal tensile specimens were tested using a high rate hydraulic testing machine. Specimens were machined from four sheets with different thicknesses, 1, 1.5, 2 and 3 mm, along three directions, 0°, 45°, and 90° to the rolling direction. The results revealed that all the specimens had a positive strain rate sensitivity of strength, that is, the strength increased with increasing strain rate. This is the same tendency as other automotive steels have. Our results suggest that the AZ31 magnesium alloy has better collision characteristics at high strain rates because of improved strength with an increasing strain rate. Ductility decreased with an increasing strain rate with a strain rate under 1 s"-1, but it increased with an increasing strain rate over 1 s"-1. The mechanical properties of the AZ31 magnesium alloy depend on the different microstructures according to the thickness. Two and 3 mm thickness specimens with a coarse and non-uniform grain structure exhibited worse mechanical properties while the 1.5 mm thickness specimens with a fine and uniform grain structure had better mechanical properties. Specimens machined at 0° and 45° to the rolling direction had higher absorbed energy than that of the 90° specimen. Thus, we demonstrate it is necessary to choose materials with proper thickness and machining direction for use in automotive applications.

A biometeorology study of climate and heat-related morbidity in Phoenix from 2001 to 2006

Science.gov (United States)

Golden, Jay S.; Hartz, Donna; Brazel, Anthony; Luber, George; Phelan, Patrick

2008-07-01

Heat waves kill more people in the United States than hurricanes, tornadoes, earthquakes, and floods combined. Recently, international attention focused on the linkages and impacts of human health vulnerability to urban climate when Western Europe experienced over 30,000 excess deaths during the heat waves of the summer of 2003—surpassing the 1995 heat wave in Chicago, Illinois, that killed 739. While Europe dealt with heat waves, in the United States, Phoenix, Arizona, established a new all-time high minimum temperature for the region on July 15, 2003. The low temperature of 35.5°C (96°F) was recorded, breaking the previous all-time high minimum temperature record of 33.8°C (93°F). While an extensive literature on heat-related mortality exists, greater understanding of influences of heat-related morbidity is required due to climate change and rapid urbanization influences. We undertook an analysis of 6 years (2001 2006) of heat-related dispatches through the Phoenix Fire Department regional dispatch center to examine temporal, climatic and other non-spatial influences contributing to high-heat-related medical dispatch events. The findings identified that there were no significant variations in day-of-week dispatch events. The greatest incidence of heat-related medical dispatches occurred between the times of peak solar irradiance and maximum diurnal temperature, and during times of elevated human comfort indices (combined temperature and relative humidity).

Iron Phosphate Glass for Vitrifying Hanford AZ102 LAW in Joule Heated and Cold Crucible Induction Melters - 12240

Energy Technology Data Exchange (ETDEWEB)

Day, Delbert E.; Brow, Richard K.; Ray, Chandra S.; Reis, Signo T. [Missouri University of Science and Technology, 1870 Miner Circle, Rolla, MO 65409 (United States); Kim, Cheol-Woon [MO-SCI Corporation, 4040 HyPoint North, Rolla, MO 65401 (United States); Vienna, John D.; Sevigny, Gary [Pacific North West National Laboratory, Battelle Blvd., Richland, WA 99352 (United States); Peeler, David; Johnson, Fabienne C.; Hansen, Eric K. [Savannah River National Laboratory, Savannah River Site, 999-W, Aiken, SC 29803 (United States); Soelberg, Nick [Idaho National Laboratory, 2525 Fremont Avenue, Idaho Falls, ID 83415 (United States); Pegg, Ian L.; Gan, Hao [Catholic University of America, 620 Michigan Avenue, N.E., Washington, DC 20064 (United States)

2012-07-01

An iron phosphate composition for vitrifying a high sulfate (∼17 wt%) and high alkali (∼80 wt%) Hanford low activity waste (LAW), known as AZ-102 LAW, has been developed for processing in a Joule Heated Melter (JHM) or a Cold Crucible Induction Melter (CCIM). This composition produced a glass waste form, designated as MS26AZ102F-2, with a waste loading of 26 wt% of the AZ-102 which corresponded to a total alkali and sulfate (represented as SO{sub 3}) content of 21 and 4.4 wt%, respectively. A slurry (7 M Na{sup +}) of MS26AZ102F-2 simulant was melted continuously at temperatures between 1030 and 1090 deg. C for 10 days in a small JHM at PNNL and for 70 hours in a CCIM at INL. The as-cast glasses produced in both melters and in trial laboratory experiments along with their canister centerline cooled (CCC) counterparts met the requirements for the Product Consistency Test (PCT) and the Vapor Hydration Test (VHT) responses in the Hanford Tank Waste Treatment and Immobilization Plant (WTP) Contract. These glass waste forms retained up to 77 % of the SO{sub 3} (3.3 wt%), 100% of the Cesium, and 33 to 44% of the rhenium (used as a surrogate for Tc) all of which either exceeded or were comparable to the retention limit for these species in borosilicate glass nuclear waste form. Analyses of commercial K-3 refractory lining and the Inconel 693 metal electrodes used in JHM indicated only minimum corrosion of these components by the iron phosphate glass. This is the first time that an iron phosphate composition was melted continuously in a slurry fed JHM and in the US, thereby, demonstrating that iron phosphate glasses can be used as alternative hosts for vitrifying nuclear waste. The following conclusions are drawn from the results of the present work. (1) An iron phosphate composition, designated as MS26AZ102F-2, containing 26 wt% of the simulated high sulfate (17 wt%), high alkali (80 wt%) Hanford AZ-102 LAW meets all the criteria for processing in a JHM and CCIM. This

Corrosion behaviour of AZ91D and AM50 magnesium alloys with Nd and Gd additions in humid environments

Energy Technology Data Exchange (ETDEWEB)

Arrabal, R., E-mail: raularrabal@quim.ucm.es [Departamento de Ciencia de Materiales, Facultad de Ciencias Quimicas, Universidad Complutense, 28040 Madrid (Spain); Matykina, E.; Pardo, A.; Merino, M.C. [Departamento de Ciencia de Materiales, Facultad de Ciencias Quimicas, Universidad Complutense, 28040 Madrid (Spain); Paucar, K. [Gabinete de Corrosion, Facultad de Ingenieria Quimica y Textil, Universidad Nacional de Ingenieria, Cod. Postal 25, Lima (Peru); Mohedano, M.; Casajus, P. [Departamento de Ciencia de Materiales, Facultad de Ciencias Quimicas, Universidad Complutense, 28040 Madrid (Spain)

2012-02-15

Highlights: Black-Right-Pointing-Pointer Mg alloys with additions of Nd and Gd were exposed to high humidity atmosphere. Black-Right-Pointing-Pointer The increase of Nd or Gd diminished the effect of micro-galvanic couples. Black-Right-Pointing-Pointer Corrosion resistance of the AM50 alloy improved with the addition of Nd or Gd by 43%. Black-Right-Pointing-Pointer Nd and Gd had no significant effect on the corrosion resistance of the AZ91D alloy. - Abstract: AM50 and AZ91D alloys modified with rare earths (RE) were evaluated under atmospheric conditions. Nd and Gd additions resulted in formation of Al{sub 2}RE and Al-Mn-RE compounds and reduction of the fraction of {beta}-phase. According to surface potential maps, RE-containing intermetallics were more noble than the {beta}-phase, but less than Al-Mn inclusions. As a result, the action of micro-galvanic couples depended on the added amount of RE and the initial alloy microstructure. Nd or Gd additions improved the corrosion resistance of the AM50 alloy by up to 43%, but had no significant effect on the corrosion resistance of the AZ91D alloy.

Corrosion behaviour of AZ91D and AM50 magnesium alloys with Nd and Gd additions in humid environments

International Nuclear Information System (INIS)

Arrabal, R.; Matykina, E.; Pardo, A.; Merino, M.C.; Paucar, K.; Mohedano, M.; Casajús, P.

2012-01-01

Highlights: ► Mg alloys with additions of Nd and Gd were exposed to high humidity atmosphere. ► The increase of Nd or Gd diminished the effect of micro-galvanic couples. ► Corrosion resistance of the AM50 alloy improved with the addition of Nd or Gd by 43%. ► Nd and Gd had no significant effect on the corrosion resistance of the AZ91D alloy. - Abstract: AM50 and AZ91D alloys modified with rare earths (RE) were evaluated under atmospheric conditions. Nd and Gd additions resulted in formation of Al 2 RE and Al–Mn–RE compounds and reduction of the fraction of β-phase. According to surface potential maps, RE-containing intermetallics were more noble than the β-phase, but less than Al–Mn inclusions. As a result, the action of micro-galvanic couples depended on the added amount of RE and the initial alloy microstructure. Nd or Gd additions improved the corrosion resistance of the AM50 alloy by up to 43%, but had no significant effect on the corrosion resistance of the AZ91D alloy.

Factores de competitividad de la agroindustria de la caña de azúcar en México

Directory of Open Access Journals (Sweden)

Noé Aguilar Rivera

2011-01-01

Full Text Available La industria azucarera de México integra actividades agrícolas de crecimiento, cosecha y transporte de caña a la producción de azúcar estándar y refinada, con otros productos y subproductos. Para competir en una economía global, es importante establecer criterios de desempeño para reducir costos de producción en términos de competitividad técnica, productividad y eficiencia en aspectos como rendimientos, caña de azúcar y agroindustrial por hectárea y de fábrica. En este artículo se discuten algunos indicadores de competitividad económica y técnica de la industria de caña de azúcar mexicana, con metodologías de benchmarking y diamante de Porter. Los resultados mostraron que son numerosos los factores técnicos y económicos que limitan el crecimiento, debido a que la industria mexicana se ha mantenido no competitiva y requiere mejorar e innovar en la reducción de costos, sobre todo en materia prima, cosecha y transporte. También está la diversificación, con base en los subproductos, como residuos de cosecha, bagazo, melazas, lodo de filtros y vinazas; esto es de gran importancia como fuente renovable de energía y materias primas.

Influence of Route-R on wrought magnesium AZ61 alloy mechanical properties through equal channel angular pressing

Directory of Open Access Journals (Sweden)

Muralidhar Avvari

2014-06-01

Full Text Available A new fundamental route entitled ‘Route-R’ is introduced to refine the grains in the material through Equal Channel Angular Pressing (ECAP process. In route R, specimen is inverted to the original position in each ECAP pass. In the present work, AZ61 alloy is processed using ECAP process for three different fundamental routes mainly route A, route Bc, and route R. ECAP experiment is carried out on AZ61 alloy at lower temperature of 483 K up to two passes. Microstructural characterization is evaluated on unECAPed and ECAPed specimens for three routes. Average grain size of the alloy is to be reduced from 66 μm to 16 μm, 14.1 μm and 10 μm for route A routes Bc, and route R respectively. Vickers microhardness of the alloy is found to be 60 HV for as received material. This microhardness of the alloy is increased to 71 HV, 72 HV, and 74 HV for route A, route Bc, and route R respectively. Mechanical properties of the AZ61 alloy are observed to be route R is providing maximum YS, UTS, and percentage elongation than other route A and route Bc. Tensile fracture topography of the specimen is analyzed using three different routes for two passes.

Temporal regulation of foregut development by HTZ-1/H2A.Z and PHA-4/FoxA.

Directory of Open Access Journals (Sweden)

Dustin L Updike

2006-09-01

Full Text Available The histone variant H2A.Z is evolutionarily conserved and plays an essential role in mice, Drosophila, and Tetrahymena. The essential function of H2A.Z is unknown, with some studies suggesting a role in transcriptional repression and others in activation. Here we show that Caenorhabditis elegans HTZ-1/H2A.Z and the remodeling complex MYS-1/ESA1-SSL-1/SWR1 synergize with the FoxA transcription factor PHA-4 to coordinate temporal gene expression during foregut development. We observe dramatic genetic interactions between pha-4 and htz-1, mys-1, and ssl-1. A survey of transcription factors reveals that this interaction is specific, and thus pha-4 is acutely sensitive to reductions in these three proteins. Using a nuclear spot assay to visualize HTZ-1 in living embryos as organogenesis proceeds, we show that HTZ-1 is recruited to foregut promoters at the time of transcriptional onset, and this recruitment requires PHA-4. Loss of htz-1 by RNAi is lethal and leads to delayed expression of a subset of foregut genes. Thus, the effects of PHA-4 on temporal regulation can be explained in part by recruitment of HTZ-1 to target promoters. We suggest PHA-4 and HTZ-1 coordinate temporal gene expression by modulating the chromatin environment.

77 FR 20356 - Foreign-Trade Zone 277-Western Maricopa County, AZ; Application for Manufacturing Authority...

Science.gov (United States)

2012-04-04

... Maricopa County, AZ; Application for Manufacturing Authority; Suntech Arizona, Inc., (Solar Panel... facility is used for the manufacture of 275 and 290 watt solar panels for industrial use. Components and... to solar panels (duty-free) for the foreign inputs noted above. Suntech would also be exempt from...

Characteristic values for the forming of the magnesium alloy AZ31

International Nuclear Information System (INIS)

Doege, E.; Janssen, S.; Wieser, J.

2001-01-01

The aim of investigation and development at the institute for metal forming and metal forming machine tools (IFUM) at the University of Hanover, Germany is to advance magnesium forming scientifically which has so far been based on experience and empirically determined process data only. Optimized process parameter with a sound material scientific and process control base have to be determined for the deformation of magnesium wrought alloys in order to broaden the technical use of such alloys. Aim of the investigations introduced in this paper is the determination of characteristic values as well-founded basis for the forming technological processing of magnesium wrought alloys in massive forming processes. The basic data for the description of the deformation ability in the form of friction factor and flow curve is to be detected, especially in connection with the integration into an FEM-simulation. In order to achieve such data for the magnesium wrought alloy AZ31 the flow curve at temperatures between 250 and 300 C and the deformation ratio 1, 10, 20 and 30 are presented. On the other hand a ring upsetting test for the determination of the friction factor at altitude reductions of 30, 50, 70%, a tool temperature of 200 C, a work piece temperature between 300 and 400 C and different lubricants are shown for the said alloy. (orig.)

Microstructure and corrosion behavior of laser surface-treated AZ31B Mg bio-implant material.

Science.gov (United States)

Wu, Tso-Chang; Ho, Yee-Hsien; Joshi, Sameehan S; Rajamure, Ravi S; Dahotre, Narendra B

2017-05-01

Although magnesium and magnesium alloys are considered biocompatible and biodegradable, they suffer from poor corrosion performance in the human body environment. In light of this, surface modification via rapid surface melting of AZ31B Mg alloy using a continuous-wave Nd:YAG laser was conducted. Laser processing was performed with laser energy ranging from 1.06 to 3.18 J/mm 2 . The corrosion behavior in simulated body fluid of laser surface-treated and untreated AZ31B Mg alloy samples was evaluated using electrochemical technique. The effect of laser surface treatment on phase and microstructure evolution was evaluated using X-ray diffraction and scanning electron microscopy. Microstructure examination revealed grain refinement as well as formation and uniform distribution of Mg 17 Al 12 phase along the grain boundary for laser surface-treated samples. Evolution of such unique microstructure during laser surface treatment indicated enhancement in the corrosion resistance of laser surface-treated samples compared to untreated alloy.

Evaluation of self-healing ability of Ce–V conversion coating on AZ31 magnesium alloy

Directory of Open Access Journals (Sweden)

Xiao Jiang

2016-09-01

Full Text Available This study investigated the influence of cerium nitrate in vanadate solutions on the properties of Ce–V conversion coatings on AZ31 magnesium alloys, and evaluated the self-healing behavior of the Ce–V conversion coating for AZ31 magnesium alloy. The results showed that the additions of cerium nitrate prevented pentavalent vanadium from reducing to tetravalent vanadium in the coatings during conversion reaction process. Adding appropriate cerium nitrate to vanadate solution led to a thicker coating with a more compact CeVO4 layer. The corrosion behavior of the Ce–V conversion coating was investigated by the electrochemical tests and the scratch immersion test in 3.5 wt.% NaCl solution. The self-healing ability of the coating was confirmed from all tests. The surface analysis revealed that the self-healing effect of the Ce–V conversion coating was only provided by the release and migration of vanadium compounds.

Mechanical properties of plasma-sprayed layers of aluminium and aluminium alloy on AZ 91

Czech Academy of Sciences Publication Activity Database

Kubatík, Tomáš František; Ctibor, Pavel; Mušálek, Radek; Janata, Marek

2017-01-01

Roč. 51, č. 2 (2017), s. 323-327 ISSN 1580-2949 R&D Projects: GA ČR(CZ) GP14-31538P Institutional support: RVO:61389021 Keywords : plasma spraying of aluminium * adhesion of coating * wear * magnesium alloy AZ91 Subject RIV: JG - Metallurgy OBOR OECD: Materials engineering Impact factor: 0.436, year: 2016

TiO2 Deposition on AZ31 Magnesium Alloy Using Plasma Electrolytic Oxidation

Directory of Open Access Journals (Sweden)

Leon White

2013-01-01

Full Text Available Plasma electrolytic oxidation (PEO has been used in the past as a useful surface treatment technique to improve the anticorrosion properties of Mg alloys by forming protective layer. Coatings were prepared on AZ31 magnesium alloy in phosphate electrolyte with the addition of TiO2 nanoparticles using plasma electrolytic oxidation (PEO. This present work focuses on developing a TiO2 functional coating to create a novel electrophotocatalyst while observing the surface morphology, structure, composition, and corrosion resistance of the PEO coating. Microstructural characterization of the coating was investigated by X-ray diffraction (XRD and scanning electron microscopy (SEM followed by image analysis and energy dispersive spectroscopy (EDX. The corrosion resistance of the PEO treated samples was evaluated with electrochemical impedance spectroscopy (EIS and DC polarization tests in 3.5 wt.% NaCl. The XRD pattern shows that the components of the oxide film include Mg from the substrate as well as MgO and Mg2TiO4 due to the TiO2 nanoparticle addition. The results show that the PEO coating with TiO2 nanoparticles did improve the corrosion resistance when compared to the AZ31 substrate alloy.

Ultrasonic Examination of Double-Shell Tank 241-AZ-102 Examination Completed August 2003

International Nuclear Information System (INIS)

Pardini, Allan F.; Posakony, Gerald J.

2003-01-01

COGEMA Engineering Corporation (COGEMA), under a contract from CH2M Hill Hanford Group (CH2M Hill), has performed an ultrasonic nondestructive examination of selected portions of Double-Shell Tank 241-AZ-102. The purpose of this examination was to provide information that could be used to evaluate the integrity of the wall of the primary tank. The requirements for the ultrasonic examination of Tank 241-AZ-102 were to detect, characterize (identify, size, and locate), and record measurements made of any wall thinning, pitting, or cracks that might be present in the wall of the primary tank. Any measurements that exceed the requirements set forth in the Engineering Task Plat (ETP), RPP-11832 (Jensen 2002) and summarized on page 1 of this document, are reported to CH2M Hill and the Pacific Northwest National Laboratory (PNNL) for further evaluation. Under the contract with CH2M Hill, all data is to be recorded on disk and paper copies of all measurements are provided to PNNL for third-party evaluation. PNNL is responsible for preparing a report that describes the results of the COGEMA ultrasonic examinations

Room Temperature Shear Band Development in Highly Twinned Wrought Magnesium AZ31B Sheet

Science.gov (United States)

Scott, Jon; Miles, Michael; Fullwood, David; Adams, Brent; Khosravani, Ali; Mishra, Raja K.

2013-01-01

Failure mechanisms were studied in wrought AZ31B magnesium alloy after forming under different strain paths. Optical micrographs were used to observe the shear band formation and regions of high twin density in samples strained under uniaxial, biaxial, and plane strain conditions. Interrupted testing at 4 pct effective strain increments, until failure, was used to observe the evolution of the microstructure. The results showed that shear bands, with a high percentage of twinned grains, appeared early in the samples strained under biaxial or plane strain tension. These bands are similar to those seen in uniaxial tension specimens just prior to failure where the uniaxial tensile ductility was much greater than that observed for plane strain or biaxial tension conditions. A forming limit diagram for AZ31B, which was developed from the strain data, showed that plane strain and biaxial tension had very similar limit strains; this contrasts with materials like steel or aluminum alloys, which typically have greater ductility in biaxial tension compared to plane strain tension.

Improvement of high temperature fatigue lifetime in AZ91 magnesium alloy by heat treatment

International Nuclear Information System (INIS)

Mokhtarishirazabad, Mehdi; Azadi, Mohammad; Hossein Farrahi, Gholam; Winter, Gerhard; Eichlseder, Wilfred

2013-01-01

In the present paper, an improvement in high temperature fatigue properties of the AZ91 magnesium alloy with rare earth elements has been obtained by a typical heat treatment, denoted by T6. For this objective, out-of-phase thermo-mechanical fatigue, room temperature and high temperature low cycle fatigue tests are performed to compare lifetimes. Several rare earth elements are initially added to the AZ91 alloy during a gravity casting process in permanent molds. Also, the type of the heat treatment is examined. Results of specimens with only the solution (the T4 heat treatment) and the solution with the ageing process (the T6 heat treatment) are compared under isothermal fatigue loadings. Microstructural investigations are carried out, before and after fatigue experiments to demonstrate the heat treatment effect. Results showed that both low cycle fatigue and thermo-mechanical fatigue of the alloy at high temperatures increases tremendously after the T6 heat treatment. This behavior attributes to the variation of the ductility, which was a result of microstructural changes during the heat treatment and the varying temperature in fatigue tests

Improvement of high temperature fatigue lifetime in AZ91 magnesium alloy by heat treatment

Energy Technology Data Exchange (ETDEWEB)

Mokhtarishirazabad, Mehdi [School of Metallurgy and Materials Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Azadi, Mohammad, E-mail: m_azadi@ip-co.com [Fatigue and Wear Workgroup, Irankhodro Powertrain Company (IPCO), Tehran (Iran, Islamic Republic of); Hossein Farrahi, Gholam [School of Mechanical Engineering, Sharif University of Technology, Tehran (Iran, Islamic Republic of); Winter, Gerhard; Eichlseder, Wilfred [Chair of Mechanical Engineering, University of Leoben, Leoben (Austria)

2013-12-20

In the present paper, an improvement in high temperature fatigue properties of the AZ91 magnesium alloy with rare earth elements has been obtained by a typical heat treatment, denoted by T6. For this objective, out-of-phase thermo-mechanical fatigue, room temperature and high temperature low cycle fatigue tests are performed to compare lifetimes. Several rare earth elements are initially added to the AZ91 alloy during a gravity casting process in permanent molds. Also, the type of the heat treatment is examined. Results of specimens with only the solution (the T4 heat treatment) and the solution with the ageing process (the T6 heat treatment) are compared under isothermal fatigue loadings. Microstructural investigations are carried out, before and after fatigue experiments to demonstrate the heat treatment effect. Results showed that both low cycle fatigue and thermo-mechanical fatigue of the alloy at high temperatures increases tremendously after the T6 heat treatment. This behavior attributes to the variation of the ductility, which was a result of microstructural changes during the heat treatment and the varying temperature in fatigue tests.

Thermal and Evolved Gas Behavior of Calcite Under Mars Phoenix TEGA Operating Conditions

Science.gov (United States)

Ming, D.W.; Niles, P.B.; Morris, R.V.; Boynton, W.V.; Golden, D.C.; Lauer, H.V.; Sutter, B.

2009-01-01

The Mars Phoenix Scout Mission with its diverse instrument suite successfully examined several soils on the Northern plains of Mars. The Thermal and Evolved Gas Analyzer (TEGA) was employed to detect organic and inorganic materials by coupling a differential scanning calorimeter (DSC) with a magnetic-sector mass spectrometer (MS). Martian soil was heated up to 1000 C in the DSC ovens and evolved gases from mineral decomposition products were examined with the MS. TEGA s DSC has the capability to detect endothermic and exothermic reactions during heating that are characteristic of minerals present in the Martian soil. Initial TEGA results indicated the presence of endothermic peaks with onset temperatures that ranged from 675 C to 750 C with corresponding CO2 release. This result suggests the presence of calcite (CaCO3. CaO + CO2). Organic combustion to CO2 is not likely since this mostly occurs at temperatures below 550 C. Fe-carbonate and Mg-carbonate are not likely because their decomposition temperatures are less than 600 C. TEGA enthalpy determinations suggest that calcite, may occur in the Martian soil in concentrations of approx.1 to 5 wt. %. The detection of calcite could be questioned based on previous results that suggest Mars soils are mostly acidic. However, the Phoenix landing site soil pH was measured at pH 8.3 0.5, which is typical of terrestrial soils where pH is controlled by calcite solubility. The range of onset temperatures and calcite concentration as calculated by TEGA is poorly con-strained in part because of limited thermal data of cal-cite at reduced pressures. TEGA operates at calcite literature thermal data was obtained at 1000 mbar or higher pressures.

Anther development and microsporogenesis in date palm (phoenix dactylifera l.)

International Nuclear Information System (INIS)

Jazinizadeh, E.; Majd, A.; Pourpak, Z.

2017-01-01

Microsporogenesis and pollen morphology of Phoenix dactylifera L. was studied in this study. Anther, in different developmental stages, was removed, fixed in Formalin-glacial acetic acid-alcohol (FAA), stored in 70% ethanol, embedded in paraffin and then sliced at 8-10mu m by rotary microtome. Staining was carried out with Hematoxylin-Eozin. Scanning electron microscope (SEM) was used to analyze the mature pollen grains. The pollen protein extracts of date palm were obtained from pollen by phosphate buffer saline (PBS). They were separated by 10% SDS-polyacrylamide gel electrophoresis. The anther wall is constituted of five cellular strata: epidermis, monostratified endothecium, middle layer formed by two cellular strata and the secretory tapetum. The microspore mother cells begin meiosis and form tetrads of tetragonal microspores. The mature anther wall consists of an epidermis and an endothecium. Mature pollen grains are two-celled and monosulcate, semitectate -reticulate. SDS- PAGE analysis of mature pollen grains showed protein bands of 10-110 kDa regions. (author)

El legado psicológico de Rogelio Díaz-Guerrero

OpenAIRE

Reynaldo Alarcón

2010-01-01

O autor identifica quatro dimensões básicas na obra do psicólogo mexicano Rogelio Díaz-Guerrero (1918-2004): a) seu interesse pioneiro por construir uma psicología do mexicano se inicia com a publicação de Estudios de psicología del mexicano (1961) e culmina 42 anos depois com seu livro Bajo las garras de la cultura. Psicología del mexicano 2 (2003); b) a orientação culturalista de seu pensamento; c) sua adesão à psicologia transcultural, em reação ao etnocentrismo psicológico dominante em su...

Effect of the Strain Rate on the Tensile Properties of the AZ31 Magnesium Alloy

Energy Technology Data Exchange (ETDEWEB)

Jeong, Seunghun; Park, Jiyoun; Choi, Ildong [Korea Maritime University, Busan (Korea, Republic of); Park, Sung Hyuk [Korea Institute of Materials Science, Changwon (Korea, Republic of)

2013-10-15

The effect of the strain rate at a range of 10‒4 ⁓ 3 × 10{sup 2}s{sup -}1 on the tensile characteristics of a rolled AZ31 magnesium alloy was studied. The normal tensile specimens were tested using a high rate hydraulic testing machine. Specimens were machined from four sheets with different thicknesses, 1, 1.5, 2 and 3 mm, along three directions, 0°, 45°, and 90° to the rolling direction. The results revealed that all the specimens had a positive strain rate sensitivity of strength, that is, the strength increased with increasing strain rate. This is the same tendency as other automotive steels have. Our results suggest that the AZ31 magnesium alloy has better collision characteristics at high strain rates because of improved strength with an increasing strain rate. Ductility decreased with an increasing strain rate with a strain rate under 1 s{sup -}1, but it increased with an increasing strain rate over 1 s{sup -}1. The mechanical properties of the AZ31 magnesium alloy depend on the different microstructures according to the thickness. Two and 3 mm thickness specimens with a coarse and non-uniform grain structure exhibited worse mechanical properties while the 1.5 mm thickness specimens with a fine and uniform grain structure had better mechanical properties. Specimens machined at 0° and 45° to the rolling direction had higher absorbed energy than that of the 90° specimen. Thus, we demonstrate it is necessary to choose materials with proper thickness and machining direction for use in automotive applications.

Interfacial Reaction Characteristics and Mechanical Properties of Welding-brazing Bonding Between AZ31B Magnesium Alloy and PRO500 Ultra-high Strength Steel

Directory of Open Access Journals (Sweden)

CHEN Jian-hua

2017-11-01

Full Text Available Experiments were carried out with TIG welding-brazing of AZ31B magnesium alloy to PRO500 steel using TIG arc as heat source. The interfacial reaction characteristics and mechanical properties of the welding-brazing bonding were investigated. The results show that an effective bonding is achieved between AZ31B magnesium alloy and PRO500 steel by using TIG welding-brazing method. Some spontaneous oxidation reactions result in the formation of a transition zone containing AlFe3 phase with rich oxide. The micro-hardness value of the interfacial transition zone is between that of the AZ31B and the PRO500. Temper softening zone appears due to the welding thermal cycle nearby the bonding position in the interface. A higher heat input makes an increase of the brittle phases and leads to an obvious decrease of the bonding strength.

Reemplazo de grasa y azúcar en magdalenas. Efecto sobre las propiedades reológicas, térmicas, de textura y sensoriales

OpenAIRE

MARTÍNEZ CERVERA, SANDRA

2013-01-01

El presente trabajo de tesis se centra en el estudio de las propiedades reológicas, térmicas, de textura y sensoriales de magdalenas en las que se ha reemplazado parcial o totalmente la grasa o el azúcar. La masa de las magdalenas es una emulsión de aceite en agua compuesta por una base de harina que incorpora grasa y azúcar como ingredientes principales y, como opcionales, huevo, leche y otros componentes. El producto final se caracteriza por tener una estructura poro...

Feminism and Postmodernism in Paloma Díaz-Mas's "The World According to Valdés" and "In Search of a Portrait"

Directory of Open Access Journals (Sweden)

Fuencisla Zomeño

2002-06-01

Full Text Available This paper analyzes the influence of postmodernism in Paloma Díaz-Mas's feminist approach through two short stories, "The World According to Valdés," and "In Search of a Portrait." The political situation after Franco's death embraced democracy which allowed writers to pay more attention to intellectual concerns. Women writers steered the radical positions of the 1970s toward a more philosophical and intellectual analysis of reality and artistic expression during the eighties. In these two short stories, Díaz-Mas addresses women's issues by questioning the scope of modernist and humanist views. She criticizes the modernist concept of unity (text/identity pointing out the discrimination that this unity creates in art, through the distinction between high art/mass culture; and in the individual, through the distinction between feminine/masculine and high/low. Even though Díaz-Mas's main characters in the two stories are women, she does not solely focus on defending them, but she contrasts present and past to parody the causes which produce discrimination in the social and artistic processes.

A New Factor in American Destiny: Visions of Porfirio Díaz and the Politics of “Logical Paternalism”

Directory of Open Access Journals (Sweden)

Jason Ruiz

2011-12-01

Full Text Available This essay interprets American representations of dictator Porfirio Díaz in relation to the “economic conquest” of Mexico that took place during his long rule (1876–1911, a period known as the “Porfiriato,” in which Americans invested more than $1 billion. No single person inspired as much attention from travelers, reporters, and photographers during the late nineteenth and early twentieth centuries as Díaz, and their visions of the President helped to shape perceptions of Mexico as a desirable field in which to expand US capitalism and influence. Travelers clamored to meet him and his sophisticated young wife, and their travelogues were rich with descriptions of such encounters. Reporters, dazzled by the rapid transformation of Mexico during his 35-year rule, described Díaz in such terms as “the Mexican Wizard” and “the maker of modern Mexico” until the very end of his regime. Photographers, working in a relatively new medium, amassed a huge body of works devoted to the dictator; even at an advanced age late in his rule, the President’s image adorned postcards and commemorative cartes-de-visite that posited him in heroic and hypermasculine terms (not unlike those of his US counterpart, Theodore Roosevelt. Ultimately, this essay argues that representations like these reflected American desires for a Mexican body politic that was amenable to economic and social transformation under the inextricable banners of “progress” and US capitalism. Prevailing images of Díaz and his family suggested that Mexico was as friendly to foreign investors as it was to foreign visitors.

Chemical Composition of Date Palm (Phoenix dactylifera L.) Seed Oil from Six Saudi Arabian Cultivars.

Science.gov (United States)

Nehdi, Imeddedine Arbi; Sbihi, Hassen Mohamed; Tan, Chin Ping; Rashid, Umer; Al-Resayes, Saud Ibrahim

2018-03-01

This investigation aimed to evaluate the chemical composition and physicochemical properties of seed oils from 6 date palm (Phoenix. dactylifera L.) cultivars (Barhi, Khalas, Manifi, Rezeiz, Sulaj, and Sukkari) growing in Saudi Arabia and to compare them with conventional palm olein. The mean oil content of the seeds was about 7%. Oleic acid (48.67%) was the main fatty acid, followed by lauric acid (17.26%), stearic acid (10.74%), palmitic acid (9.88%), and linolenic acid (8.13%). The mean value for free fatty acids content was 0.5%. The P. dactylifera seed oil also exhibited a mean tocol content of 70.75 mg/100 g. α-Tocotrienol was the most abundant isomer (30.19%), followed by γ-tocopherol (23.61%), γ-tocotrienol (19.07%), and α-tocopherol (17.52%). The oils showed high thermal and oxidative stabilities. The findings indicate that date seed oil has the potential to be used in the food industry as an abundant alternative to palm olein. This study showed that date seed had great nutritional value due to which it can be used for food applications especially as frying or cooking oil. In addition, date oil has also potential to be used in cosmetic and pharmaceutical practices as well. The extraction of oil from Phoenix dactylifera seed on large scale can create positive socioeconomic benefits especially for rural communities and could also assist to resolve the environmental issues generated by excess date production in large scale date-producing countries such as Saudi Arabia. © 2018 Institute of Food Technologists®.

The applicability of ALPHA/PHOENIX/ANC nuclear design code system on Korean standard PWR's

International Nuclear Information System (INIS)

Lee, Kookjong; Choi, Kie-Yong; Lee, Hae-Chan; Roh, Eun-Rae

1996-01-01

For the Korean Standard Nuclear Power Plant (KSNPP) designed based on Combustion Engineering (CE) System 80, the Westinghouse nuclear design code system ALPHA/PHOENIX/ANC was applied to the follow-up design of initial and reload core of KSNPP. The follow-up design results of Yonggwang Unit 3 Cycle 1, 2 and Yonggwang Unit 4 Cycle 1 have shown good agreements with the measured data. The assemblywise power distributions have shown less than 2% average differences and critical boron concentrations have shown less than 20 ppm differences. All the low power physics test parameters are in good agreement. Consequently, APA design code system can be applied to KNSPP cores. (author)

Evaluating the Phoenix definition of biochemical failure after (125)I prostate brachytherapy: Can PSA kinetics distinguish PSA failures from PSA bounces?

Science.gov (United States)

Thompson, Anna; Keyes, Mira; Pickles, Tom; Palma, David; Moravan, Veronika; Spadinger, Ingrid; Lapointe, Vincent; Morris, W James

2010-10-01

To evaluate the prostate-specific antigen (PSA) kinetics of PSA failure (PSAf) and PSA bounce (PSAb) after permanent (125)I prostate brachytherapy (PB). The study included 1,006 consecutive low and "low tier" intermediate-risk patients treated with (125)I PB, with a potential minimum follow-up of 4 years. Patients who met the Phoenix definition of biochemical failure (nadir + 2 ng/mL(-1)) were identified. If the PSA subsequently fell to ≤0.5 ng/mL(-1)without intervention, this was considered a PSAb. All others were scored as true PSAf. Patient, tumor and dosimetric characteristics were compared between groups using the chi-square test and analysis of variance to evaluate factors associated with PSAf or PSAb. Median follow-up was 54 months. Of the 1,006 men, 57 patients triggered the Phoenix definition of PSA failure, 32 (56%) were true PSAf, and 25 PSAb (44%). The median time to trigger nadir + 2 was 20.6 months (range, 6-36) vs. 49 mo (range, 12-83) for PSAb vs. PSAf groups (p < 0.001). The PSAb patients were significantly younger (p < 0.0001), had shorter time to reach the nadir (median 6 vs. 11.5 months, p = 0.001) and had a shorter PSA doubling time (p = 0.05). Men younger than age 70 who trigger nadir +2 PSA failure within 38 months of implant have an 80% likelihood of having PSAb and 20% chance of PSAf. With adequate follow-up, 44% of PSA failures by the Phoenix definition in our cohort were found to be benign PSA bounces. Our study reinforces the need for adequate follow-up when reporting PB PSA outcomes, to ensure accurate estimates of treatment efficacy and to avoid unnecessary secondary interventions. 2010. Published by Elsevier Inc. All rights reserved.

Evaluating the Phoenix Definition of Biochemical Failure After 125I Prostate Brachytherapy: Can PSA Kinetics Distinguish PSA Failures From PSA Bounces?

International Nuclear Information System (INIS)

Thompson, Anna; Keyes, Mira; Pickles, Tom

2010-01-01

Purpose: To evaluate the prostate-specific antigen (PSA) kinetics of PSA failure (PSAf) and PSA bounce (PSAb) after permanent 125 I prostate brachytherapy (PB). Methods and Materials: The study included 1,006 consecutive low and 'low tier' intermediate-risk patients treated with 125 I PB, with a potential minimum follow-up of 4 years. Patients who met the Phoenix definition of biochemical failure (nadir + 2 ng/mL -1 ) were identified. If the PSA subsequently fell to ≤0.5 ng/mL -1 without intervention, this was considered a PSAb. All others were scored as true PSAf. Patient, tumor and dosimetric characteristics were compared between groups using the chi-square test and analysis of variance to evaluate factors associated with PSAf or PSAb. Results: Median follow-up was 54 months. Of the 1,006 men, 57 patients triggered the Phoenix definition of PSA failure, 32 (56%) were true PSAf, and 25 PSAb (44%). The median time to trigger nadir + 2 was 20.6 months (range, 6-36) vs. 49 mo (range, 12-83) for PSAb vs. PSAf groups (p < 0.001). The PSAb patients were significantly younger (p < 0.0001), had shorter time to reach the nadir (median 6 vs. 11.5 months, p = 0.001) and had a shorter PSA doubling time (p = 0.05). Men younger than age 70 who trigger nadir +2 PSA failure within 38 months of implant have an 80% likelihood of having PSAb and 20% chance of PSAf. Conclusions: With adequate follow-up, 44% of PSA failures by the Phoenix definition in our cohort were found to be benign PSA bounces. Our study reinforces the need for adequate follow-up when reporting PB PSA outcomes, to ensure accurate estimates of treatment efficacy and to avoid unnecessary secondary interventions.

Possible Calcite and Magnesium Perchlorate Interaction in the Mars Phoenix Thermal and Evolved Gas Analyzer (TEGA)

Science.gov (United States)

Cannon, K. M.; Sutter, B.; Ming, D. W.; Boynton, W. V.; Quinn, R. C.

2012-01-01

The Mars Phoenix Lander's TEGA instrument detected a calcium carbonate phase decomposing at high temperatures (approx.700 C) from the Wicked Witch soil sample [1]. TEGA also detected a lower temperature CO2 release between 400 C and 680 C [1]. Possible explanations given for this lower temperature CO2 release include thermal decomposition of Mg or Fe carbonates, a zeolitictype desorption reaction, or combustion of organic compounds in the soil [2]. The detection of 0.6 wt % soluble perchlorate by the Wet Chemistry Laboratory (WCL) on Phoenix [3] has implications for the possibility of organic molecules in the soil. Ming et al. [4] demonstrated that perchlorates could have oxidized organic compounds to CO2 in TEGA, preventing detection of their characteristic mass fragments. Here, we propose that a perchlorate salt and calcium carbonate present in martian soil reacted to produce the 400 C - 680 C TEGA CO2 release. The parent salts of the perchlorate on Mars are unknown, but geochemical models using WCL data support the possible dominance of Mg-perchlorate salts [5]. Mg(ClO4)2 6H2O is the stable phase at ambient martian conditions [6], and breaks down at lower temperatures than carbonates giving off Cl2 and HCl gas [7,8]. Devlin and Herley [7] report two exotherms at 410-478 C and 473-533 C which correspond to the decomposition of Mg(ClO4)2.

Corrosion fatigue behaviors of two biomedical Mg alloys - AZ91D and WE43 - In simulated body fluid.

Science.gov (United States)

Gu, X N; Zhou, W R; Zheng, Y F; Cheng, Y; Wei, S C; Zhong, S P; Xi, T F; Chen, L J

2010-12-01

Magnesium alloys have been recently developed as biodegradable implant materials, yet there has been no study concerning their corrosion fatigue properties under cyclic loading. In this study the die-cast AZ91D (A for aluminum 9%, Z for zinc 1% and D for a fourth phase) and extruded WE43 (W for yttrium 4%, E for rare earth mischmetal 3%) alloys were chosen to evaluate their fatigue and corrosion fatigue behaviors in simulated body fluid (SBF). The die-cast AZ91D alloy indicated a fatigue limit of 50MPa at 10⁷ cycles in air compared to 20MPa at 10⁶ cycles tested in SBF at 37°C. A fatigue limit of 110MPa at 10⁷ cycles in air was observed for extruded WE43 alloy compared to 40MPa at 10⁷ cycles tested in SBF at 37°C. The fatigue cracks initiated from the micropores when tested in air and from corrosion pits when tested in SBF, respectively. The overload zone of the extruded WE43 alloy exhibited a ductile fracture mode with deep dimples, in comparison to a brittle fracture mode for the die-cast AZ91D. The corrosion rate of the two experimental alloys increased under cyclic loading compared to that in the static immersion test. Copyright © 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Application of heat treatment and hot extrusion processes to improve mechanical properties of the AZ91 alloy

Directory of Open Access Journals (Sweden)

T. Reguła

2010-04-01

Full Text Available The main aim of this paper is to evaluate the effects of hot working (extrusion and hest treatment on room temperature mechanical properties of magnesium-based AZ91 alloy. The results were compared with as-cast condition. The examined material had been obtained by gravity casting to permanent moulds and subsequently subjected to heat treatment and/or processed by extrusion at 648 K. Microstructural and mechanical properties of properly prepared specimens were studied. Rm, Rp02 and A5 were determined from tensile tests. Brinell hardness tests were also conducted. The research has shown that hot working of AZ91 alloy provides high mechanical properties unattainable by cast material subjected to heat-treatment. The investigated alloy subjected to hot working and subsequently heat-treated has doubled its strength and considerably improved the elongation - compared with the as-cast material.

Reactive Sequencing for Autonomous Navigation Evolving from Phoenix Entry, Descent, and Landing

Science.gov (United States)

Grasso, Christopher A.; Riedel, Joseph E.; Vaughan, Andrew T.

2010-01-01

Virtual Machine Language (VML) is an award-winning advanced procedural sequencing language in use on NASA deep-space missions since 1997, and was used for the successful entry, descent, and landing (EDL) of the Phoenix spacecraft onto the surface of Mars. Phoenix EDL utilized a state-oriented operations architecture which executed within the constraints of the existing VML 2.0 flight capability, compatible with the linear "land or die" nature of the mission. The intricacies of Phoenix EDL included the planned discarding of portions of the vehicle, the complex communications management for relay through on-orbit assets, the presence of temporally indeterminate physical events, and the need to rapidly catch up four days of sequencing should a reboot of the spacecraft flight computer occur shortly before atmospheric entry. These formidable operational challenges led to new techniques for packaging and coordinating reusable sequences called blocks using one-way synchronization via VML sequencing global variable events. The coordinated blocks acted as an ensemble to land the spacecraft, while individually managing various elements in as simple a fashion as possible. This paper outlines prototype VML 2.1 flight capabilities that have evolved from the one-way synchronization techniques in order to implement even more ambitious autonomous mission capabilities. Target missions for these new capabilities include autonomous touch-and-go sampling of cometary and asteroidal bodies, lunar landing of robotic missions, and ultimately landing of crewed lunar vehicles. Close proximity guidance, navigation, and control operations, on-orbit rendezvous, and descent and landing events featured in these missions require elaborate abort capability, manifesting highly non-linear scenarios that are so complex as to overtax traditional sequencing, or even the sort of one-way coordinated sequencing used during EDL. Foreseeing advanced command and control needs for small body and lunar landing

Bernal Díaz del Castillo, la memoria y la representación

Directory of Open Access Journals (Sweden)

María Luisa Fischer

2016-04-01

Full Text Available En este trabajo se analizan los procedimientos narrativos que verosimilizan la versión de la historia que define Bernal Díaz del Castillo. Se analiza la función que en el total del relato cumplen los capítulos de largos listados que lo cierran y, especialmente, el capítulo CCVI, dedicado a los retratos indistinguibles de los capitanes españoles de la Nueva España. Se muestra cómo la memoria privilegiada del cronista está funcionando bajo el predicamento de una retórica -en este caso, la del retrato del héroe, de origen medieval- que disputa su lugar frente a la pretendida reconstrucción de la experiencia por la vía única de la memoria. This work analyse the narrative procedures which Bernal Díaz del Castillo uses to make his version of history appear to be probable. The function of the long lists at the end of the story and, especially of Chapter CCVI, containing the indistinguishable portraits of New Spain's Spanish capitains is explained. How the chronicler's privileged memory functions as a rhetorical category -in this case, that of the portrait of a medieval hero- who argues his case for the pretended reconstruction of an experience based only on memory is shown.

El abordaje comparativo de 'La conquista' en dos autores mestizos: Garcilaso de la Vega y Ruiz Díaz Guzmán A comparative approach about 'La conquista' in the work of two mestizo authors: Garcilaso de la Vega y Ruiz Díaz Guzmán

Directory of Open Access Journals (Sweden)

Sebastián Eduardo Pardo

2011-12-01

Full Text Available El artículo propone analizar la representación del proceso de dominación colonial, coloquialmente conocido como "La Conquista", en los trabajos de dos autores pertenecientes a las primeras generaciones de mestizos de principios del siglo XVII: Garcilaso de la Vega y Ruy Díaz de Guzmán. La elección responde a dos cuestiones fundamentales; por un lado, ambos expresan un fuerte sentido de pertenencia regional al autodenominarse "naturales" de las áreas culturales sobre las cuales escriben; por la otra, ambos mantienen una relación compleja pero bien diferenciada con respecto a la problemática del mestizaje adscribiendo a identidades étnicas opuestas: mientras Garcilaso se presenta como inca, Ruy Díaz de Guzmán lo hace como español. En este sentido se discutirán las trayectorias de los mencionados autores para llevar a cabo el análisis comparado de sus vidas, sus ideologías y sus obras.This paper analyses the representation of colonial domination, process commonly known as "The Conquest", in the work of two writers belonging to the first half-breed generations of the early 17th century: Garcilaso de la Vega and Ruy Díaz de Guzmán. The selection is based on two fundamental criteria: on the one hand both declare themselves as "naturales" and reveal a strong sense of belonging regarding the cultural areas they describe; on the other hand, both attach themselves to opposite ethnic identities, thus maintaining a different relationship with the complex problems of mestizaje and miscegenation -while Garcilaso claims to be an Inca, Ruy Díaz de Guzmán introduces himself as a Spaniard. Therefore, the biographies of both authors are discussed in order to understand their life trajectories, ideologies and work from a comparative point of view.

Corrosion resistance of titanium ion implanted AZ91 magnesium alloy

International Nuclear Information System (INIS)

Liu Chenglong; Xin Yunchang; Tian Xiubo; Zhao, J.; Chu, Paul K.

2007-01-01

Degradable metal alloys constitute a new class of materials for load-bearing biomedical implants. Owing to their good mechanical properties and biocompatibility, magnesium alloys are promising in degradable prosthetic implants. The objective of this study is to improve the corrosion behavior of surgical AZ91 magnesium alloy by titanium ion implantation. The surface characteristics of the ion implanted layer in the magnesium alloys are examined. The authors' results disclose that an intermixed layer is produced and the surface oxidized films are mainly composed of titanium oxide with a lesser amount of magnesium oxide. X-ray photoelectron spectroscopy reveals that the oxide has three layers. The outer layer which is 10 nm thick is mainly composed of MgO and TiO 2 with some Mg(OH) 2 . The middle layer that is 50 nm thick comprises predominantly TiO 2 and MgO with minor contributions from MgAl 2 O 4 and TiO. The third layer from the surface is rich in metallic Mg, Ti, Al, and Ti 3 Al. The effects of Ti ion implantation on the corrosion resistance and electrochemical behavior of the magnesium alloys are investigated in simulated body fluids at 37±1 deg. C using electrochemical impedance spectroscopy and open circuit potential techniques. Compared to the unimplanted AZ91 alloy, titanium ion implantation significantly shifts the open circuit potential (OCP) to a more positive potential and improves the corrosion resistance at OCP. This phenomenon can be ascribed to the more compact surface oxide film, enhanced reoxidation on the implanted surface, as well as the increased β-Mg 12 Al 17 phase

Investigation of the chemical vicinity of defects in Mg and AZ31 with positron coincident Doppler boarding spectroscopy

International Nuclear Information System (INIS)

Stadlbauer, Martin

2008-01-01

Within the scope of the present work, two main goals have been achieved: Firstly, the coincident Doppler broadening spectrometer (CDBS) at the high intense positron source NEPOMUC has been elaborately improved in order to increase the spatial resolution for defect mapping measurements and to investigate samples with shallow positron trapping sites which are present e. g. in magnesium. Secondly, as an application, the chemical vicinity of defects in the industrially used magnesium based alloy AZ31 has been examined by means of the detailed investigation of ion-irradiated specimen with positron annihilation spectroscopy. Detailed simulations with the finite-element simulation tool COMSOL were used to optimize the focal diameter of the positron beam at the sample position in order to increase the spatial resolution. With a value of 0.3 mm, sub-mm resolution has now been reached. The CDBS has been furthermore equipped with a sample cooling unit in order to reach liquid nitrogen temperature, maintaining the feature of scanning the sample for defect mapping. Defects and their chemical surrounding in ion irradiated magnesium and the magnesium based alloy AZ31 were then investigated on an atomic scale with the CDBS. In the respective spectra the chemical information and the defect contribution have been thoroughly separated. For this purpose, samples of annealed Mg were irradiated with Mg-ions in order to create exclusively defects. In addition Al- and Zn-ion irradiations on Mg-samples were performed in order to create samples with both defects and impurity atoms. The ion irradiated area on the samples was investigated with laterally and depth resolved positron Doppler broadening spectroscopy (DBS) and compared with SRIM-simulations of the vacancy distribution. The investigation of the chemical vicinity of crystal defects in AZ31 was performed with CDBS on Mg-ion irradiated AZ31 with Mg-ion irradiated Mg. The outer tail of the energy distribution in the annihilation

Investigation of the chemical vicinity of defects in Mg and AZ31 with positron coincident Doppler boarding spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Stadlbauer, Martin

2008-03-10

Within the scope of the present work, two main goals have been achieved: Firstly, the coincident Doppler broadening spectrometer (CDBS) at the high intense positron source NEPOMUC has been elaborately improved in order to increase the spatial resolution for defect mapping measurements and to investigate samples with shallow positron trapping sites which are present e. g. in magnesium. Secondly, as an application, the chemical vicinity of defects in the industrially used magnesium based alloy AZ31 has been examined by means of the detailed investigation of ion-irradiated specimen with positron annihilation spectroscopy. Detailed simulations with the finite-element simulation tool COMSOL were used to optimize the focal diameter of the positron beam at the sample position in order to increase the spatial resolution. With a value of 0.3 mm, sub-mm resolution has now been reached. The CDBS has been furthermore equipped with a sample cooling unit in order to reach liquid nitrogen temperature, maintaining the feature of scanning the sample for defect mapping. Defects and their chemical surrounding in ion irradiated magnesium and the magnesium based alloy AZ31 were then investigated on an atomic scale with the CDBS. In the respective spectra the chemical information and the defect contribution have been thoroughly separated. For this purpose, samples of annealed Mg were irradiated with Mg-ions in order to create exclusively defects. In addition Al- and Zn-ion irradiations on Mg-samples were performed in order to create samples with both defects and impurity atoms. The ion irradiated area on the samples was investigated with laterally and depth resolved positron Doppler broadening spectroscopy (DBS) and compared with SRIM-simulations of the vacancy distribution. The investigation of the chemical vicinity of crystal defects in AZ31 was performed with CDBS on Mg-ion irradiated AZ31 with Mg-ion irradiated Mg. The outer tail of the energy distribution in the annihilation

Mt Pamola, the Electromagnetic Field, EMF, Thunderbird, Mothman and Environmental Monitoring Signals Via the Southern Constellation Phoenix As Detectable In Potato Cave, Acton, MA.

Science.gov (United States)

Pecora, Andrea S.; Pawa Matagamon, Sagamo

2004-03-01

Just below the peak of Mt Pamola in ME, at the juncture with the Knife Edge, downwardly arcing segments of Earths EMF, are manifested by a faint lotus-blossom-blue, neon-like glow at 3 pm some sunny afternoons. Similarly hued glows, and horizontal but variable-arced segmented trajectories, are somewhat periodically detectable under certain conditions in chambers at Acton, MA. These phenomena curiously have the filled-in profile that precisely matches the outline of the southern constellation Phoenix, which is never visible above the nighttime horizon locally. The stick-figure representation of the constellation Canis Major can also be detected in a chamber at Americas Stonehenge, two hours before it has arisen, at certain times. The sequence of phenomena visible at Acton correctly correlates with eclipses and other alignments of our solar system. Phoenix, a.k.a. Thunderbird and Mothman, is detectable elsewhere in MA.

Simulation of AZ-PN100 resist pattern fluctuation in X-ray lithography, including synchrotron beam polarization

International Nuclear Information System (INIS)

Scheckler, E.W.; Ogawa, Taro; Tanaka, Toshihiko; Takeda, Eiji; Oizumi, Hiroaki.

1993-01-01

A new simulation model for nanometer-scale pattern fluctuation in X-ray lithography is presented and applied to a study of AZ-PN100 negative chemical amplification resist. The exposure simulation considers polarized photons from a synchrotron radiation (SR) source. Monte Carlo simulation of Auger and photoelectron generation is followed by electron scattering simulation to determine the deposited energy distribution at the nanometer scale, including beam polarization effects. An acid-catalyst random walk model simulates the post-exposure bake (PEB) step. Fourier transform infrared (FTIR) spectroscopy and developed resist thickness measurements are used to fit PEB and rate models for AZ-PN100. A polymer removal model for development simulation predicts the macroscopic resist shape and pattern roughness. The simulated 3σ linewidth variation is in excess of 24 nm. Simulation also shows a detrimental effect if the beam polarization is perpendicular to the line. Simulation assuming a theoretical ideal exposure yields a 50 nm minimum line for standard process conditions. (author)

Optimization of process factors for self-healing vanadium-based conversion coating on AZ31 magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Li, Kun; Liu, Junyao [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Lei, Ting, E-mail: tlei@mail.csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Xiao, Tao [2nd Xiangya Hospital, Central South University, Changsha 410011 (China)

2015-10-30

Highlights: • The optimum operating conditions were determined by an orthogonal experiment. • The coating is composed of oxides and hydroxides of V{sup 5+}, V{sup 4+} and Mg(OH){sub 2}. • The self-healing performance was investigated by cross-cut immersion test. • The vanadia conversion coating provided active corrosion protection to AZ31 alloy. - Abstract: A self-healing vanadium-based conversion coating was prepared on AZ31 magnesium alloy. The optimum operating conditions including vanadia solution concentration, pH and treating temperature for obtaining the best corrosion protective vanadia coatings and improved localized corrosion resistance to the magnesium substrate were determined by an orthogonal experiment design. Surface morphology and composition of the resultant conversion coatings were investigated by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The self-healing behavior of the coating was investigated by cross-cut immersion test and electrochemical impedance spectroscopy (EIS) measurements in 3.5% NaCl solution.

Optimization of process factors for self-healing vanadium-based conversion coating on AZ31 magnesium alloy

International Nuclear Information System (INIS)

Li, Kun; Liu, Junyao; Lei, Ting; Xiao, Tao

2015-01-01

Highlights: • The optimum operating conditions were determined by an orthogonal experiment. • The coating is composed of oxides and hydroxides of V"5"+, V"4"+ and Mg(OH)_2. • The self-healing performance was investigated by cross-cut immersion test. • The vanadia conversion coating provided active corrosion protection to AZ31 alloy. - Abstract: A self-healing vanadium-based conversion coating was prepared on AZ31 magnesium alloy. The optimum operating conditions including vanadia solution concentration, pH and treating temperature for obtaining the best corrosion protective vanadia coatings and improved localized corrosion resistance to the magnesium substrate were determined by an orthogonal experiment design. Surface morphology and composition of the resultant conversion coatings were investigated by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The self-healing behavior of the coating was investigated by cross-cut immersion test and electrochemical impedance spectroscopy (EIS) measurements in 3.5% NaCl solution.

Influence of Friction Stir Welding on Mechanical Properties of Butt Joints of AZ61 Magnesium Alloy

Directory of Open Access Journals (Sweden)

Seung-Ju Sun

2017-01-01

Full Text Available In this study, the effect of heat input on the mechanical properties and fracture behaviors of AZ61 magnesium alloy joints has been studied. Magnesium alloy AZ61 plates with thickness of 5 mm were welded at different ratios of tool rotational speed to welding speed (ω/ν. The average ultimate tensile strength of all weld conditions satisfying a ω/ν ratio of 3 reached 100% of the strength of the base material. Fractures occurred at the interface between the thermomechanical affected zone at advancing side and the stir zone in all welded specimens. From the scanning electron microscope and electron backscatter diffraction analysis, it was determined that the interface between the thermomechanical affected zone and the stir zone, which is the region where the grain orientation changes, was the weakest part; the advancing side region was relatively weaker than the retreating side region because the grain orientation change occurred more dramatically in the advancing side region.