Fabrication and testing of W7-X pre-series target elements

International Nuclear Information System (INIS)

Boscary, J; Boeswirth, B; Greuner, H; Grigull, P; Missirlian, M; Plankensteiner, A; Schedler, B; Friedrich, T; Schlosser, J; Streibl, B; Traxler, H

2007-01-01

The assembly of the highly-loaded target plates of the WENDELSTEIN 7-X (W7-X) divertor requires the fabrication of 890 target elements (TEs). The plasma facing material is made of CFC NB31 flat tiles bonded to a CuCrZr copper alloy water-cooled heat sink. The elements are designed to remove a stationary heat flux and power up to 10 MW m -2 and 100 kW, respectively. Before launching the serial fabrication, pre-series activities aimed at qualifying the design, the manufacturing route and the non-destructive examinations (NDEs). High heat flux (HHF) tests performed on full-scale pre-series TEs resulted in an improvement of the design of the bond between tiles and heat sink to reduce the stresses during operation. The consequence is the fabrication of additional pre-series TEs to be tested in the HHF facility GLADIS. NDEs of this bond based on thermography methods are developed to define the acceptance criteria suitable for serial fabrication

Fabrication of laser-target components by semiconductor technology

International Nuclear Information System (INIS)

Tindall, W.E.

1979-01-01

This paper describes the design and fabrication of a unique silicon substrate with which laser-target components can be mass produced. Different sizes and shapes of gold foils from 50 to 3000 microns in diameter and up to 25 microns thick have been produced with this process since 1976

Inertial Confinement Fusion Target Component Fabrication and Technology Development report

International Nuclear Information System (INIS)

Steinman, D.

1994-03-01

On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities which took place under this contract during the period of October 1, 1992 through September 30, 1993. During this period, GA was assigned 18 tasks in support of the Inertial Confinement Fusion program and its laboratories. These tasks included ''Capabilities Activation'' and ''Capabilities Demonstration'' to enable us to begin production of glass and composite polymer capsules. Capsule delivery tasks included ''Small Glass Shell Deliveries'' and ''Composite Polymer Capsules'' for Lawrence Livermore National Laboratory (LLNL) and Los Alamos National Laboratory (LANL). We also were asked to provide direct ''Onsite Support'' at LLNL and LANL. We continued planning for the transfer of ''Micromachining Equipment from Rocky Flats'' and established ''Target Component Micromachining and Electroplating Facilities'' at GA. We fabricated over 1100 films and filters of 11 types for Sandia National Laboratory and provided full-time onsite engineering support for target fabrication and characterization. We initiated development of methods to make targets for the Naval Research Laboratory. We investigated spherical interferometry, built an automated capsule sorter, and developed an apparatus for calorimetric measurement of fuel fill for LLNL. We assisted LANL in the ''Characterization of Opaque b-Layered Targets.'' We developed deuterated and UV-opaque polymers for use by the University of Rochester's Laboratory for Laser Energetics (UR/LLE) and devised a triple-orifice droplet generator to demonstrate the controlled-mass nature of the microencapsulation process

Addressing key science and technology issues for IFE chambers, target fabrication and target injection

International Nuclear Information System (INIS)

Meier, W.R.; Goodin, D.T.; Nobile, A.

2003-01-01

Significant progress has been made in the development of high repetition rate chambers, target fabrication and injection for inertial fusion energy (IFE) for both heavy ion and laser drivers. Research is being conducted in a coordinated manner by national laboratories, universities and industry. This paper provides an overview of U.S. research activities and discusses how interface considerations (such as beam propagation and target survival during injection) impact design choices. (author)

Investigation on cryogenic laser fusion targets: fabrication, characterization, and transport. Annual report, December 1, 1978-November 30, 1979

International Nuclear Information System (INIS)

Kim, K.

1979-01-01

The research has been directed toward fabrication, characterization, and positioning of cryogenic shell laser fusion targets, with particular emphasis on the development of a scheme which would allow for continuous fabrication, inspection, and delivery of the targets. Specifically, progress has been made in the following areas: (1) Fabrication of a uniform spherical shell of DT-condensate using a cold-wall target-freezing-cell. (2) Fabrication of a uniform spherical shell of liquid DT using a room-temperature wall target-freezing-cell. (3) Support-free cryogenic target fabrication using cold-gas-levitation. (4) Continuous fabrication of cryogenic targets using free-fall method. (5) Automatic characterization of DT-layer uniformity. (6) Sorting of DT-filled glass microshells using an interference microscope. (7) Development of an a-c interference microscope for accurate characterization of moving targets. (8) Development of a machine which is capable of producing a continuous stream of uniform DT spheres of controllable sizes. (9) Theoretical study on the behavior of liquid hydrogen contained in a spherical shell

Role of Fabrication on Materials Compatibility in APT Target/Blanket

International Nuclear Information System (INIS)

Iyer, N.; Louthan, M.R. Jr.; Dunn, K.; Fisher, D.L.

1998-09-01

This paper summarizes several of the options associated with the fabrication of selected target/blanket components. In addition, the materials characterization technologies required to validate these components performance is presented

Investigation on fabrication and positioning of cryogenic shell laser fusion targets. Annual report, October 1, 1977--November 30, 1978

International Nuclear Information System (INIS)

Kim, K.

1978-01-01

The research has been directed toward fabrication and positioning of cryogenic shell laser fusion targets, with particular emphasis on the development of a scheme which would allow for continuous fabrication, inspection, and delivery of the targets. Specifically, progress has been made in each of the following areas: (1) fabrication of a uniform layer of solid DT inside a glass microshell using a combination of helium gas jets and a heater wire; (2) levitation-freezing of a DT-filled glass microshell as a method for fabricating and positioning a cryogenic shell target; (3) a target fabrication system intended for continuous fabrication, inspection, and delivery of cryogenic targets; and (4) development of diagnostics for inspection, recording, and analysis of a solid DT layer inside a glass microshell, and for observing the parameters controlling the target freezing process

Fabrication of cryogenic inertial-confinement-fusion targets using target free-fall technique. Report No. 2-82

International Nuclear Information System (INIS)

Kim, K.; Murphy, M.J.

1982-04-01

Techniques for fabricating cryogenic inertial confinement fusion targets (i.e., spherical shells containing a uniform layer of DT ice) are investigated using target free-fall concept. Detection and characterization of the moving targets are effected by optoelectronic means, of which the principal is an RF ac-interferometer. This interferometer system demonstrates, for the first time, the speed capabilities of the phase-modulation ac-interferometry. New techiques developed for handling, holding, launching, and transporting targets are also described. Results obtained at both room and cryogenic temperatures are presented

The fabrication techniques of Z-pinch targets. Techniques of fabricating self-adapted Z-pinch wire-arrays

International Nuclear Information System (INIS)

Qiu Longhui; Wei Yun; Liu Debin; Sun Zuoke; Yuan Yuping

2002-01-01

In order to fabricate wire arrays for use in the Z-pinch physical experiments, the fabrication techniques are investigated as follow: Thickness of about 1-1.5 μm of gold is electroplated on the surface of ultra-fine tungsten wires. Fibers of deuterated-polystyrene (DPS) with diameters from 30 to 100 microns are made from molten DPS. And two kinds of planar wire-arrays and four types of annular wire-arrays are designed, which are able to adapt to the variation of the distance between the cathode and anode inside the target chamber. Furthermore, wire-arrays with diameters form 5-24 μm are fabricated with tungsten wires, respectively. The on-site test shows that the wire-arrays can self-adapt to the distance changes perfectly

Complete fabrication of target experimental chamber and implement initial target diagnostics to be used for the first target experiments in NDCX-1

International Nuclear Information System (INIS)

Bieniosek, F.M.; Bieniosek, F.M.; Dickinson, M.R.; Henestroza, E.; Katayanagi, T.; Jung, J.Y.; Lee, C.W.; Leitner, M.; Ni, P.; Roy, P.; Seidl, P.; Waldron, W.; Welch, D.

2008-01-01

The Heavy Ion Fusion Science Virtual National Laboratory (HIFS-VNL) has completed the fabrication of a new experimental target chamber facility for future Warm Dense Matter (WDM) experiments, and implemented initial target diagnostics to be used for the first target experiments in NDCX-1. The target chamber has been installed on the NDCX-I beamline. This achievement provides to the HIFS-VNL unique and state-of-the-art experimental capabilities in preparation for the planned target heating experiments using intense heavy ion beams

Powder Metallurgy Fabrication of Molybdenum Accelerator Target Disks

Energy Technology Data Exchange (ETDEWEB)

Lowden, Richard Andrew [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kiggans Jr., James O. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Nunn, Stephen D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Parten, Randy J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-07-01

Powder metallurgy approaches for the fabrication of accelerator target disks are being examined to support the development of Mo-99 production by NorthStar Medical Technologies, LLC. An advantage of powder metallurgy is that very little material is wasted and, at present, dense, quality parts are routinely produced from molybdenum powder. The proposed targets, however, are thin wafers, 29 mm in diameter with a thickness of 0.5 mm, with very stringent dimensional tolerances. Although tooling can be machined to very high tolerance levels, the operations of powder feed, pressing and sintering involve complicated mechanisms, each of which affects green density and shrinkage, and therefore the dimensions and shape of the final product. Combinations of powder morphology, lubricants and pressing technique have been explored to produce target disks with minimal variations in thickness and little or no distortion. In addition, sintering conditions that produce densities for optimum target dissolvability are being determined.

Fabrication and characterization of cryogenic targets for inertial confinement fusion

International Nuclear Information System (INIS)

Rieger, H.; Kim, K.

1979-08-01

A new technique has been developed which is capable of fabricating uniform cryogenic targets for use in inertial confinement fusion. The essence of the technique is to directly wet a target with a cold helium gas jet, which results in freezing of the DT mixture contained in the target. A controlled amount of current is pulsed through a heater wire surrounding the target, giving rise to fast evaporation and refreezing of the DT-condensate into a uniform layer. Experiments, which have been performed with D 2 -filled glass microshells, successfully produce uniform layers of both liquid and solid D 2 inside the glass shells. A set of data illustrating the technique is presented and analyzed

Tenth target fabrication specialists' meeting: Proceedings

International Nuclear Information System (INIS)

Foreman, L.R.; Stark, J.C.

1995-01-01

This tenth meeting of specialists in target fabrication for inertial confinement is unique in that it is the first meeting that was completely unclassified. As a result of the new classification, we were able to invite more foreign participation. In addition to participants from the US, UK, and Canada, representatives from France, Japan, and two Russian laboratories attended, about 115 in all. This booklet presents full papers and poster sessions. Indirect and direct drive laser implosions are considered. Typical topics include: polymer or aluminium or resorcinol/formaldehyde shells, laser technology, photon tunneling microscopy as a characterization tool, foams, coatings, hohlraums, and beryllium capsules. Hydrogen, deuterium, tritium, and beryllium are all considered as fuels

Tenth target fabrication specialists` meeting: Proceedings

Energy Technology Data Exchange (ETDEWEB)

Foreman, L.R.; Stark, J.C. [comp.

1995-11-01

This tenth meeting of specialists in target fabrication for inertial confinement is unique in that it is the first meeting that was completely unclassified. As a result of the new classification, we were able to invite more foreign participation. In addition to participants from the US, UK, and Canada, representatives from France, Japan, and two Russian laboratories attended, about 115 in all. This booklet presents full papers and poster sessions. Indirect and direct drive laser implosions are considered. Typical topics include: polymer or aluminium or resorcinol/formaldehyde shells, laser technology, photon tunneling microscopy as a characterization tool, foams, coatings, hohlraums, and beryllium capsules. Hydrogen, deuterium, tritium, and beryllium are all considered as fuels.

Energy efficiency improvement target for SIC 34 - fabricated metal products. Revised target support document

Energy Technology Data Exchange (ETDEWEB)

Byrer, T. G.; Billhardt, C. F.; Farkas, M. S.

1977-02-15

In accordance with section 374 of the Energy Policy and Conservation Act (EPCA), Pub. L. 94-163, the Federal Energy Administration (FEA) proposed industrial energy efficiency improvement targets for the ten most energy-consumptive manufacturing industries in the U.S. Following public hearings and a review of the comments made, the final targets for Fabricated Metal Products (SIC 34) were established and are described. Using 1972 data on the energy consumed to produce specific metal products, it was concluded that a 24% reduction in energy consumption for SIC 34 is a viable goal for achievement by 1980. (ERA citation 04:045006)

Information-management data base for fusion-target fabrication processes

International Nuclear Information System (INIS)

Reynolds, J.

1982-01-01

A computer-based data-management system has been developed to handle data associated with target-fabrication processes including glass microballoon characterization, gas filling, materials coating, and storage locations. The system provides automatic data storage and computation, flexible data-entry procedures, fast access, automated report generation, and secure data transfer. It resides on a CDC CYBER 175 computer and is compatible with the CDC data-base-language Query Update, but is based on custom FORTRAN software interacting directly with the CYBER's file-management system. The described data base maintains detailed, accurate, and readily available records of fusion targets information

Information management data base for fusion target fabrication processes

International Nuclear Information System (INIS)

Reynolds, J.

1983-01-01

A computer-based data management system has been developed to handle data associated with target fabrication processes including glass microballoon characterization, gas filling, materials coating, and storage locations. The system provides automatic data storage and computation, flexible data entry procedures, fast access, automated report generation, and secure data transfer. It resides on a CDC CYBER 175 computer and is compatible with the CDC data base language Query Update, but is based on custom fortran software interacting directly with the CYBER's file management system. The described data base maintains detailed, accurate, and readily available records of fusion targets information

Energy efficiency improvement target for SIC 34 - fabricated metal products

Energy Technology Data Exchange (ETDEWEB)

Byrer, T. G.; Billhardt, C. F.; Farkas, M. S.

1977-03-15

A March 15, 1977 revision of a February 15, 1977 document on the energy improvement target for the Fabricated Metal Products industry (SIC 34) is presented. A net energy savings in 1980 of 24% as compared with 1972 energy consumption in SIC 34 is considered a realistic goal. (ERA citation 04:045008)

Ultra-hard AlMgB14 coatings fabricated by RF magnetron sputtering from a stoichiometric target

Science.gov (United States)

Grishin, A. M.; Khartsev, S. I.; Böhlmark, J.; Ahlgren, M.

2015-01-01

For the first time hard aluminum magnesium boride films were fabricated by RF magnetron sputtering from a single stoichiometric ceramic AlMgB14 target. Optimized processing conditions (substrate temperature, target sputtering power and target-to-substrate distance) enable fabrication of stoichiometric in-depth compositionally homogeneous films with the peak values of nanohardness 88 GPa and Young's modulus 517 GPa at the penetration depth of 26 nm and, respectively, 35 and 275 GPa at 200 nm depth in 2 μm thick film.

Process for the fabrication of aluminum metallized pyrolytic graphite sputtering targets

Science.gov (United States)

Makowiecki, Daniel M.; Ramsey, Philip B.; Juntz, Robert S.

1995-01-01

An improved method for fabricating pyrolytic graphite sputtering targets with superior heat transfer ability, longer life, and maximum energy transmission. Anisotropic pyrolytic graphite is contoured and/or segmented to match the erosion profile of the sputter target and then oriented such that the graphite's high thermal conductivity planes are in maximum contact with a thermally conductive metal backing. The graphite contact surface is metallized, using high rate physical vapor deposition (HRPVD), with an aluminum coating and the thermally conductive metal backing is joined to the metallized graphite target by one of four low-temperature bonding methods; liquid-metal casting, powder metallurgy compaction, eutectic brazing, and laser welding.

Inertial confinement fusion target component fabrication and technology development support. Annual report 10/1/98 through 9/30/99

International Nuclear Information System (INIS)

Gibson, Jane

1999-01-01

General Atomics (GA) has served as the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor for the U.S. Department of Energy since December 30, 1990. This report documents the technical activities of the period October 1, 1998 through September 30, 1999. During this period, GA and our partner Schafer Corporation were assigned 17 formal tasks in support of the ICF program and its five laboratories. A portion of the effort on these tasks included providing direct ''Onsite Support'' at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory (SNL). We fabricated and delivered over 1790 hohlraum mandrels and numerous other micromachined components to LLNL, LANL, and SNL. We produced more than 1380 glass and plastic target capsules over a wide range of sizes and designs (plus over 300 near target-quality capsules) for LLNL, LANL, SNL, and University of Rochester/Laboratory for Laser Energetic (UR/LLE). We also delivered various target foils and films for Naval Research Lab (NRL) and UWLLE in FY99. We fabricated a device to polish NIF-sized beryllium shells and prepared a laboratory for the safe operation of beryllium polishing activities. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. During FY99, the GA/Schafer portion of the GA/Schafer-UR/LLE-LANL team effort for design, procurement, installation, and testing of the OMEGA Cryogenic Target System (OCTS) that will field cryogenic targets on OMEGA was completed. All components of the OCTS were procured, fabricated, assembled, tested, and shipped to UR/LLE. Only minor documentation tasks remain to be done in FY00. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D2 or deuterium

Design and Fabrication of Titanium Target for Portable Neutron Generator

International Nuclear Information System (INIS)

Lee, Cheol Ho; Oh, Byunghoon; Chang, Daesik; Jang, Dohyun; In Sang Yeol; Park, Jaewon; Hong, Kwangpyo

2014-01-01

For the neutron generator to produce a neutron flux of the above order, a target that produces fast neutrons in the generator plays an important role, and the target is used and applied to develop the generator due to its simplicity and inexpensive. Making suitable targets for neutron production, especially mono-energy neutrons, has always been of interest. These targets have been used for neutron production reaction studies, calibration of detectors, and neutron therapy. Different studies have been carried out on deuterium and tritium for making solid targets to produce mono-energy neutron from D-D and D-T reactions. A lot of investigations have been carried out on solid target properties such as lifetime, thermal stability, neutron yield, and energy. Vaporized zirconium and titanium layers on a high thermal conductivity substrate (Cu, Mo, Ag) have been used as deuterium and tritium absorbing metals. The density of titanium is smaller than zirconium and the range of charged particles in the titanium targets is more than that in zirconium targets. Thus, titanium targets have more neutron yield than zirconium targets in a low energy beam and titanium is usually used to make a target. The titanium target was designed and simulated to determine the suitable thickness of the target. As a result of the simulation, the target was fabricated to generate fast neutrons by the reaction. The thickness of the target was measured using a profiler. The thickness of the two targets is 2.108 and 2.190 μm. The target will be applied to produce neutrons in a neutron generator

Target fabrication and development in the Centre d'Etudes de Limeil

International Nuclear Information System (INIS)

Clement, X.; Coudeville, A.; Eyharts, P.; Perrine, J.P.; Rouillard, R.

1983-10-01

The present state of research in Limeil laboratory for the production of inertial confinement fusion targets is described in this communication. A summary of typical areas, previously investigated, including new developments, is as follows: - production of hollow glass microspheres, having wide outside diameter range and aspect-ratio, using dried-alcogels, - preparation and fabrication of low density foams having plane or hemispherical shape, - deposition of a wide range of conductive materials as well as silicon and organic polymers, - development of laser and spark erosion machining which are useful tools for producing minute parts of complex targets, - characterization and analysis of plastic or coal metal coated targets, are done by using interferometry techniques and X-ray image analysis as well as X-ray absorption measurements

Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1997--September 30, 1998

Energy Technology Data Exchange (ETDEWEB)

Gibson, J. [ed.

1998-12-01

During this period, General Atomics (GA) and their partner Schafer Corporation were assigned 17 formal tasks in support of the Inertial Confinement Fusion (ICF) program and its five laboratories. A portion of the effort on these tasks included providing direct ``On-site Support`` at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). They fabricated and delivered over 1,200 hohlraum mandrels and numerous other micromachined components to LLNL, LANL, and SNLA. They produced more than 1,300 glass and plastic target capsules for LLNL, LANL, SNLA, and the University of Rochester/Laboratory for Laser Energetics (UR/LLE). They also delivered nearly 2,000 various target foils and films for Naval Research Lab (NRL) and UR/LLE in FY98. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. During FY98, great progress was made by the GA/Schafer-UR/LLE-LANL team in the design, procurement, installation, and testing of the OMEGA Cryogenic Target System (OCTS) that will field cryogenic targets on OMEGA. The design phase was concluded for all components of the OCTS and all major components were procured and nearly all were fabricated. Many of the components were assembled and tested, and some have been shipped to UR/LLE. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D{sub 2} or deuterium-tritium (DT) fuel. They are part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. They also contributed cryogenic support and developed concepts for NIF cryogenic targets. This report summarizes and documents the technical progress made on these tasks.

Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1997 - September 30, 1998

International Nuclear Information System (INIS)

Gibson, J.

1998-12-01

During this period, General Atomics (GA) and their partner Schafer Corporation were assigned 17 formal tasks in support of the Inertial Confinement Fusion (ICF) program and its five laboratories. A portion of the effort on these tasks included providing direct ''On-site Support'' at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). They fabricated and delivered over 1,200 hohlraum mandrels and numerous other micromachined components to LLNL, LANL, and SNLA. They produced more than 1,300 glass and plastic target capsules for LLNL, LANL, SNLA, and the University of Rochester/Laboratory for Laser Energetics (UR/LLE). They also delivered nearly 2,000 various target foils and films for Naval Research Lab (NRL) and UR/LLE in FY98. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. During FY98, great progress was made by the GA/Schafer-UR/LLE-LANL team in the design, procurement, installation, and testing of the OMEGA Cryogenic Target System (OCTS) that will field cryogenic targets on OMEGA. The design phase was concluded for all components of the OCTS and all major components were procured and nearly all were fabricated. Many of the components were assembled and tested, and some have been shipped to UR/LLE. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D 2 or deuterium-tritium (DT) fuel. They are part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. They also contributed cryogenic support and developed concepts for NIF cryogenic targets. This report summarizes and documents the technical progress made on these tasks

Radiation-chemical synthesis of polypropylene fabrics with sulfonic acid functional groups

Energy Technology Data Exchange (ETDEWEB)

Cho, Hyun Kug; Park, Jung Soo; Han, Do Hung, E-mail: dhhan@yumail.ac.kr; Bondar, Iuliia, E-mail: juliavad@yahoo.co

2011-04-01

A sorption-active material carrying sulfonic acid groups was synthesized by the radiation-induced graft polymerization of styrene monomer onto the surface of non-woven polypropylene fabric, followed by sulfonation of the grafted polystyrene chains. The effect of the main experimental parameters (absorbed dose, monomer concentration, reaction time) on the styrene degree of grafting was investigated. The sulfonation process with 5% chlorosulfonic acid at room temperature was investigated in detail and the optimal sulfonation conditions for the samples with a medium degree of grafting (70-140%) were determined. Densities of 3.5-5 meq/g were obtained by applying those sorption-active PP fabrics with a sulfonic acid group.

Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1995--September 30, 1996

International Nuclear Information System (INIS)

Hoppe, M.

1997-02-01

On December 30, 1990, the U.S. Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. In September 1995 this contract ended and a second contract was issued for us to continue this ICF target support work. This report documents the technical activities of the period October 1, 1995 through September 30, 1996. During this period, GA and our partners WJ Schafer Associates (WJSA) and Soane Technologies, Inc. (STI) were assigned 14 formal tasks in support of the Inertial Confinement Fusion program and its five laboratories. A portion of the effort on these tasks included providing direct open-quotes Onsite Supportclose quotes at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). We fabricated and delivered over 800 gold-plated hohlraum mandrels to LLNL, LANL and SNLA. We produced nearly 1,200 glass and plastic target capsules for LLNL, LANL, SNLA and University of Rochester/Laboratory for Laser Energetics (UR/LLE). We also delivered over 100 flat foil targets for Naval Research Lab (NRL) and SNLA in FY96. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require capsules containing cryogenic layered D 2 or deuterium-tritium (DT) fuel. We are part of the National Cryogenic Target Program to create and demonstrate viable ways to generate and characterize cryogenic layers. Substantial progress has been made on ways to both create and characterize viable layers. During FY96, significant progress was made in the design of the OMEGA Cryogenic Target System that will field cryogenic targets on OMEGA

Summary of the target-blanket breakout group

Energy Technology Data Exchange (ETDEWEB)

Capiello, M.; Bell, C. [Los Alamos National Laboratory, NM (United States); Barthold, W.

1995-10-01

This breakout group discussed a number of topics and issues pertaining to target and blanket concepts for accelerator-driven systems. This major component area is one marked by a broad spectrum of technical approaches. It is therefore less defined than other major component areas such as the accelerator and is at an earlier stage of technical needs and task specification. The working group did reach a number of general conclusions and recommendations that are summarized. The Conference and the Target/Blanket Breakout Group provided a first opportunity for people working on a variety of missions and concepts to get together and exchange information. A number of subcritical systems applicable for a spectrum of missions were proposed at the Conference and discussed in the Breakout Group. Missions included plutonium disposition, energy production, waste destruction, isotope production, and neutron scattering. The Target/Blanket Breakout Group also defined areas where parameters and data should be addressed as target/blanket design activities become more detailed and sophisticated.

Fabrication and testing of gas filled targets for large scale plasma experiments on Nova

International Nuclear Information System (INIS)

Stone, G.F.; Spragge, M.; Wallace, R.J.; Rivers, C.J.

1995-01-01

An experimental campaign on the Nova laser was started in July 1993 to study one st of target conditions for the point design of the National Ignition Facility (NIF). The targets were specified to investigate the current NIF target conditions--a plasma of ∼3 keV electron temperature and an electron density of ∼1.0 E + 21 cm -3 . A gas cell target design was chosen to confine as gas of ∼0.01 cm 3 in volume at ∼ 1 atmosphere. This paper will describe the major steps and processes necessary in the fabrication, testing and delivery of these targets for shots on the Nova Laser at LLNL

Advances in target design and fabrication for experiments on NIF

Directory of Open Access Journals (Sweden)

Obrey K.

2013-11-01

Full Text Available The ability to build target platforms for National Ignition Facility (NIF is a key feature in LANL's (Los Alamos National Laboratory Target Fabrication Program. We recently built and manufactured the first LANL targets to be fielded on NIF in March 2011. Experiments on NIF require precision component manufacturing and accurate knowledge of the materials used in the targets. The characterization of foams and aerogels, the Be ignition capsule, and machining unique components are of main material focus. One important characterization metric the physics' have determined is that the knowledge of density gradients in foams is important. We are making strides in not only locating these density gradients in aerogels and foams as a result of how they are manufactured and machined but also quantifying the density within the foam using 3D confocal micro x-ray fluorescence (μXRF imaging and 3D x-ray computed tomography (CT imaging. In addition, collaborative efforts between General Atomics (GA and LANL in the characterization of the NIF Ignition beryllium capsule have shown that the copper in the capsule migrates radially from the capsule center.

Design and fabrication of foam-insulated cryogenic target for wet-wall laser fusion reactor

International Nuclear Information System (INIS)

Norimatsu, T.; Takeda, T.; Nagai, K.; Mima, K.; Yamanaka, T.

2003-01-01

A foam insulated cryogenic target was proposed for use in a future laser fusion reactor with a wet wall. This scheme can protect the solid DT layer from melting due to surface heating by adsorption of metal vapor without significant reduction in the target gain. Design spaces for the injection velocity and the acceptable vapor pressure in the reactor are discussed. Basic technology to fabricate such structure was demonstrated by emulsion process. Concept of a cryogenic fast-ignition target with a gold guiding cone was proposed together with direct injection filling of liquid DT. (author)

Inertial confinement fusion target component fabrication and technology development support. Annual report, October 1, 1996 - September 30, 1997

International Nuclear Information System (INIS)

Gibson, J.

1998-03-01

This report documents the technical activities of the period October 1, 1996 through September 30, 1997. During this period, GA and their partner Schafer Corporation were assigned 13 formal tasks in support of the ICF program and its five laboratories. A portion of the effort on these tasks included providing direct open-quotes Onsite Supportclose quotes at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). Over 700 gold-plated hohlraum mandrels were fabricated and delivered to LLNL, LANL and SNLA. More than 1600 glass and plastic target capsules were produced for LLNL, LANL, SNLA and University of Rochester/Laboratory for Laser Energetics (UR/LLE). Nearly 2000 various target foils and films were delivered for Naval Research Lab (NRL) and UR/LLE in FY97. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D 2 or deuterium-tritium (DT) fuel. This project is part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. During FY97, significant progress was made in the design and component testing of the OMEGA Cryogenic Target System that will field cryogenic targets on OMEGA. This included major design changes, reduction in equipment, and process simplifications. This report summarizes and documents the technical progress made on these tasks

Inertial confinement fusion target component fabrication and technology development support. Annual report, October 1, 1996--September 30, 1997

Energy Technology Data Exchange (ETDEWEB)

Gibson, J. [ed.

1998-03-01

This report documents the technical activities of the period October 1, 1996 through September 30, 1997. During this period, GA and their partner Schafer Corporation were assigned 13 formal tasks in support of the ICF program and its five laboratories. A portion of the effort on these tasks included providing direct {open_quotes}Onsite Support{close_quotes} at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). Over 700 gold-plated hohlraum mandrels were fabricated and delivered to LLNL, LANL and SNLA. More than 1600 glass and plastic target capsules were produced for LLNL, LANL, SNLA and University of Rochester/Laboratory for Laser Energetics (UR/LLE). Nearly 2000 various target foils and films were delivered for Naval Research Lab (NRL) and UR/LLE in FY97. This report describes these target fabrication activities and the target fabrication and characterization development activities that made the deliveries possible. The ICF program is anticipating experiments at the OMEGA laser and the National Ignition Facility (NIF) which will require targets containing cryogenic layered D{sub 2} or deuterium-tritium (DT) fuel. This project is part of the National Cryogenic Target Program and support experiments at LLNL and LANL to generate and characterize cryogenic layers for these targets. During FY97, significant progress was made in the design and component testing of the OMEGA Cryogenic Target System that will field cryogenic targets on OMEGA. This included major design changes, reduction in equipment, and process simplifications. This report summarizes and documents the technical progress made on these tasks.

Coupling of carboxylic groups onto the surface of polystyrene parts during fused filament fabrication

Science.gov (United States)

Nagel, Jürgen; Zimmermann, Philipp; Schubert, Oliver; Simon, Frank; Schlenstedt, Kornelia

2017-11-01

A method for the fabrication of polystyrene parts, modified with carboxylic groups during Fused Filament Fabrication (FFF), is being introduced. This method is based on the application of a thin layer of a reactive polymer carrying carboxylic groups on a substrate surface. A polystyrene film is printed on top of this layer. During contact between the hot melt and the reactive layer, a Friedel-Crafts type acylation using a green catalyst takes place, which attaches the reactive polymer to the polystyrene surface. The modified surface is homogeneous, hydrophilic and able to bind copper ions. The method could be used to fabricate unique parts of polystyrene with tailored surface functionalisation. It could be applied for laboratory use, e.g. for the manufacture of lab-on-a-chip devices.

Investigation on non-glass laser fusion targets: their fabrication, characterization, and transport. Charged Particle Research Laboratory report No. 2-81, progress report, June 1, 1980-January 31, 1981

International Nuclear Information System (INIS)

Kim, K.

1981-01-01

A summary is presented of the research progress made under LLNL Subcontract 8320003 for the period of June 1, 1980 through January 31, 1981. The main theme of the research has continued to be the development of techniques for fabricating, characterizing, and transporting laser fusion targets on a continuous basis. The target fabrication techniques are intended mainly for non-glass spherical shell targets, both cryogenic and non-cryogenic. Specifically, progress has been made in each of the following categories. (1) Investigation of liquid hydrogen behavior inside a spherical laser fusion target. (2) Development of automated target characterization scheme. (3) Study of cryogenic target fabrication scheme utilizing cold-gas-levitation and electric field positioning. (4) Development of a cryogenic target fabrication system based on target free-fall method. (5) Generation of hydrogen powder using electro-hydrodynamic spraying. (6) Study of target-charging techniques for application to contactless cryogenic target fabrication. (7) Development of hollow metal sphere production technique. A brief summary of the research progress made in each category is presented

Regional Floras: the target groups, usage and feedback

NARCIS (Netherlands)

Ng, F.S.P.

1989-01-01

The target groups for regional floras may be generalized for the purpose of this discussion, into four main groups. Firstly, in the Flora Malesiana region – a major producer of tropical hardwoods and other commercial forest products – one large target is the forest industry, consisting of foresters,

Grouping and crowding affect target appearance over different spatial scales.

Directory of Open Access Journals (Sweden)

Bilge Sayim

Full Text Available Crowding is the impairment of peripheral target perception by nearby flankers. A number of recent studies have shown that crowding shares many features with grouping. Here, we investigate whether effects of crowding and grouping on target perception are related by asking whether they operate over the same spatial scale. A target letter T had two sets of flanking Ts of varying orientations. The first set was presented close to the target, yielding strong crowding. The second set was either close enough to cause crowding on their own or too far to cause crowding on their own. The Ts of the second set had the same orientation that either matched the target's orientation (Grouped condition or not (Ungrouped condition. In Experiment 1, the Grouped flankers reduced crowding independently of their distance from the target, suggesting that grouping operated over larger distances than crowding. In Experiments 2 and 3 we found that grouping did not affect sensitivity but produced a strong bias to report that the grouped orientation was present at the target location whether or not it was. Finally, we investigated whether this bias was a response or perceptual bias, rejecting the former in favor of a perceptual grouping explanation. We suggest that the effect of grouping is to assimilate the target to the identity of surrounding flankers when they are all the same, and that this shape assimilation effect differs in its spatial scale from the integration effect of crowding.

Communicating to heterogeneous target groups

DEFF Research Database (Denmark)

Pedersen, Karsten

very often have to communicate to rather heterogeneous target groups that have little more in common than a certain geographical habitat. That goes against most schoolbook teaching in the field of communication, but is none the less the terms with which that kind of communication has to live...

Fabrication of 94Zr thin target for recoil distance doppler shift method of lifetime measurement

International Nuclear Information System (INIS)

Gupta, C.K.; Rohilla, Aman; Abhilash, S.R.; Kabiraj, D.; Singh, R.P.; Mehta, D.; Chamoli, S.K.

2014-01-01

A thin isotopic 94 Zr target of thickness 520μg/cm 2 has been prepared for recoil distance Doppler shift method (RDM) lifetime measurement by using an electron beam deposition method on tantalum backing of 3.5 mg/cm 2 thickness at Inter University Accelerator Center (IUAC), New Delhi. To meet the special requirement of smoothness of surface for RDM lifetime measurement and also to protect the outer layer of 94 Zr from peeling off, a very thin layer of gold has been evaporated on a 94 Zr target on a specially designed substrate holder. In all, 143 mg of 99.6% enriched 94 Zr target material was utilized for the fabrication of 94 Zr targets. The target has been successfully used in a recent RDM lifetime measurement experiment at IUAC

Fabrication of 94Zr thin target for recoil distance doppler shift method of lifetime measurement

Science.gov (United States)

Gupta, C. K.; Rohilla, Aman; Abhilash, S. R.; Kabiraj, D.; Singh, R. P.; Mehta, D.; Chamoli, S. K.

2014-11-01

A thin isotopic 94Zr target of thickness 520 μg /cm2 has been prepared for recoil distance Doppler shift method (RDM) lifetime measurement by using an electron beam deposition method on tantalum backing of 3.5 mg/cm2 thickness at Inter University Accelerator Center (IUAC), New Delhi. To meet the special requirement of smoothness of surface for RDM lifetime measurement and also to protect the outer layer of 94Zr from peeling off, a very thin layer of gold has been evaporated on a 94Zr target on a specially designed substrate holder. In all, 143 mg of 99.6% enriched 94Zr target material was utilized for the fabrication of 94Zr targets. The target has been successfully used in a recent RDM lifetime measurement experiment at IUAC.

Cost Modeling for Fabrication of Direct Drive Inertial Fusion Energy Targets

International Nuclear Information System (INIS)

Rickman, William Samuel; Goodin, Daniel T.

2003-01-01

Chemical engineering analyses are underway for a commercial-scale [1000-MW(electric)] divinyl benzene foam-based Inertial Fusion Energy (IFE) Target Fabrication Facility (TFF). This facility is designed to supply 500,000, 4-mm-outer diameter targets per day - coated via interfacial polycondensation, dried with supercritical CO 2 , sputter coated with Au and/or Pd, and filled with deuterium-tritium layered at cryogenic temperatures and injected into the fusion chamber. Such targets would be used in a direct-drive IFE power plant.The work uses manufacturing processes being developed in the laboratory, chemical engineering scaleup principles, and established cost-estimating methods. The plant conceptual design includes a process flow diagram, mass and energy balances, equipment sizing and sketches, storage tanks, and facility views.The cost estimate includes both capital and operating costs. Initial results for a TFF dedicated to one 1000-MW(electric) plant indicate that the costs per target are well within the commercially viable range. Larger TFF plants [3000 MW(electric)] are projected to lead to significantly reduced costs per injected target. Additional cost reductions are possible by producing dried, sputter-coated empty shells at a central facility that services multiple power plants.The results indicate that the installed capital cost is about $100 million and the annual operating costs will be about $20 million, for a cost per target of about $0.17 each. These design and cost projections assume that a significant process development and scaleup program is successfully completed for all of the basic unit operations included in the facility

Report of the Fixed-Target Proton-Accelerator Group

International Nuclear Information System (INIS)

Abe, K.; Bunce, G.; Fisk, G.

1982-01-01

The fixed target proton accelerator group divided itself into two roughly equal parts. One sub-group concentrated on a high intensity (10 14 protons/sec) moderate energy (30 GeV) machine while the other worked on a moderate intensity (5 x 10 11 protons/sec) very high energy (20 TeV) machine. For experiments where the total available energy is adequate, the fixed target option added to a anti p p 20 TeV collider ring has several attractive features: (1) high luminosity afforded by intense beams striking thick solid targets; (2) secondary beams of hadrons, photons, and leptons; and (3) the versatility of a fixed target facility, where many experiments can be performed independently. The proposed experiments considered by the subgroup, including neutrino, photon, hadron, and very short lived particle beams were based both on scaled up versions of similar experiments proposed for Tevatron II at Fermilab and on the 400 GeV fixed target programs at Fermilab and CERN

Vertical group III-V nanowires on si, heterostructures, flexible arrays and fabrication

Science.gov (United States)

Wang, Deli; Soci, Cesare; Bao, Xinyu; Wei, Wei; Jing, Yi; Sun, Ke

2015-01-13

Embodiments of the invention provide a method for direct heteroepitaxial growth of vertical III-V semiconductor nanowires on a silicon substrate. The silicon substrate is etched to substantially completely remove native oxide. It is promptly placed in a reaction chamber. The substrate is heated and maintained at a growth temperature. Group III-V precursors are flowed for a growth time. Preferred embodiment vertical Group III-V nanowires on silicon have a core-shell structure, which provides a radial homojunction or heterojunction. A doped nanowire core is surrounded by a shell with complementary doping. Such can provide high optical absorption due to the long optical path in the axial direction of the vertical nanowires, while reducing considerably the distance over which carriers must diffuse before being collected in the radial direction. Alloy composition can also be varied. Radial and axial homojunctions and heterojunctions can be realized. Embodiments provide for flexible Group III-V nanowire structures. An array of Group III-V nanowire structures is embedded in polymer. A fabrication method forms the vertical nanowires on a substrate, e.g., a silicon substrate. Preferably, the nanowires are formed by the preferred methods for fabrication of Group III-V nanowires on silicon. Devices can be formed with core/shell and core/multi-shell nanowires and the devices are released from the substrate upon which the nanowires were formed to create a flexible structure that includes an array of vertical nanowires embedded in polymer.

Fabrication and calibration of FORTIS

Science.gov (United States)

Fleming, Brian T.; McCandliss, Stephan R.; Kaiser, Mary Elizabeth; Kruk, Jeffery; Feldman, Paul D.; Kutyrev, Alexander S.; Li, Mary J.; Rapchun, David A.; Lyness, Eric; Moseley, S. H.; Siegmund, Oswald; Vallerga, John; Martin, Adrian

2011-09-01

The Johns Hopkins University sounding rocket group is entering the final fabrication phase of the Far-ultraviolet Off Rowland-circle Telescope for Imaging and Spectroscopy (FORTIS); a sounding rocket borne multi-object spectro-telescope designed to provide spectral coverage of 43 separate targets in the 900 - 1800 Angstrom bandpass over a 30' x 30' field-of- view. Using "on-the-fly" target acquisition and spectral multiplexing enabled by a GSFC microshutter array, FORTIS will be capable of observing the brightest regions in the far-UV of nearby low redshift (z ~ 0.002 - 0.02) star forming galaxies to search for Lyman alpha escape, and to measure the local gas-to-dust ratio. A large area (~ 45 mm x 170 mm) microchannel plate detector built by Sensor Sciences provides an imaging channel for targeting flanked by two redundant spectral outrigger channels. The grating is ruled directly onto the secondary mirror to increase efficiency. In this paper, we discuss the recent progress made in the development and fabrication of FORTIS, as well as the results of early calibration and characterization of our hardware, including mirror/grating measurements, detector performance, and early operational tests of the microshutter arrays.

Fabrication of {sup 94}Zr thin target for recoil distance doppler shift method of lifetime measurement

Energy Technology Data Exchange (ETDEWEB)

Gupta, C.K.; Rohilla, Aman [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Abhilash, S.R.; Kabiraj, D.; Singh, R.P. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Mehta, D. [Department of Physics, Panjab University, Chandigarh 160014 (India); Chamoli, S.K., E-mail: skchamoli@physics.du.ac.in [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India)

2014-11-11

A thin isotopic {sup 94}Zr target of thickness 520μg/cm{sup 2} has been prepared for recoil distance Doppler shift method (RDM) lifetime measurement by using an electron beam deposition method on tantalum backing of 3.5 mg/cm{sup 2} thickness at Inter University Accelerator Center (IUAC), New Delhi. To meet the special requirement of smoothness of surface for RDM lifetime measurement and also to protect the outer layer of {sup 94}Zr from peeling off, a very thin layer of gold has been evaporated on a {sup 94}Zr target on a specially designed substrate holder. In all, 143 mg of 99.6% enriched {sup 94}Zr target material was utilized for the fabrication of {sup 94}Zr targets. The target has been successfully used in a recent RDM lifetime measurement experiment at IUAC.

CACAO facility. Radioactive targets at Orsay

International Nuclear Information System (INIS)

Bacri, C.O.; Petitbon-Thevenet, V.; Mottier, J.; Lefort, H.; Durnez, A.; Fortuna, F.

2014-01-01

CACAO, Chimie des Actinides et Cibles radioActives a Orsay (actinide chemistry and radioactive targets at Orsay), is a new laboratory dedicated to the fabrication and characterization of radioactive targets. It is supported by the radiochemistry group and the stable target service of the IPNO. The recurring needs of physicists working in the nuclear fuel cycle physics and the growing difficulties to obtain radioactive targets elsewhere were the main motivating factors behind the construction of this new laboratory. The first targets of 235,238 U and 232 Th have already been prepared although the full operating licenses still need to be obtained. In this paper, the installation and the equipment of CACAO will be described. An extensive study of a U test target fabricated by the CACAO laboratory has been performed and results are reported here. The different techniques used to characterize the deposit are presented and the outcome is discussed. (author)

Fabrication of aerogel capsule, bromine-doped capsule, and modified gold cone in modified target for the Fast Ignition Realization Experiment (FIREX) Project

Science.gov (United States)

Nagai, Keiji; Yang, H.; Norimatsu, T.; Azechi, H.; Belkada, F.; Fujimoto, Y.; Fujimura, T.; Fujioka, K.; Fujioka, S.; Homma, H.; Ito, F.; Iwamoto, A.; Jitsuno, T.; Kaneyasu, Y.; Nakai, M.; Nemoto, N.; Saika, H.; Shimoyama, T.; Suzuki, Y.; Yamanaka, K.; Mima, K.

2009-09-01

The development of target fabrication for the Fast Ignition Realization EXperiment (FIREX) Project is described in this paper. For the first stage of the FIREX Project (FIREX-I), the previously designed target has been modified by using a bromine-doped ablator and coating the inner gold cone with a low-density material. A high-quality bromine-doped capsule without vacuoles was fabricated from bromine-doped deuterated polystyrene. The gold surface was coated with a low-density material by electrochemical plating. For the cryogenic fuel target, a brand new type of aerogel material, phloroglucinol/formaldehyde (PF), was investigated and encapsulated to meet the specifications of 500 µm diameter and 20 µm thickness, with 30 nm nanopores. Polystyrene-based low-density materials were investigated and the relationship between the crosslinker content and the nanopore structure was observed.

Targets and processes for fabricating same

Science.gov (United States)

Adams, Jesse D; Malekos, Steven; Le Galloudec, Nathalie; Korgan, Grant; Cowan, Thomas; Sentoku, Yasuhiko

2016-05-17

In particular embodiments, the present disclosure provides targets including a metal layer and defining a hollow inner surface. The hollow inner surface has an internal apex. The distance between at least two opposing points of the internal apex is less than about 15 .mu.m. In particular examples, the distance is less than about 1 .mu.m. Particular implementations of the targets are free standing. The targets have a number of disclosed shaped, including cones, pyramids, hemispheres, and capped structures. The present disclosure also provides arrays of such targets. Also provided are methods of forming targets, such as the disclosed targets, using lithographic techniques, such as photolithographic techniques. In particular examples, a target mold is formed from a silicon wafer and then one or more sides of the mold are coated with a target material, such as one or more metals.

Targets and processes for fabricating same

Science.gov (United States)

Cowan, Thomas [Dresden, DE; Malekos, Steven [Reno, NV; Korgan, Grant [Reno, NV; Adams, Jesse [Reno, NV; Sentoku, Yasuhiko [Reno, NV; Le Galloudec, Nathalie [Reno, NV; Fuchs, Julien [Paris, FR

2012-07-24

In particular embodiments, the present disclosure provides targets including a metal layer and defining a hollow inner surface. The hollow inner surface has an internal apex. The distance between at least two opposing points of the internal apex is less than about 15 .mu.m. In particular examples, the distance is less than about 1 .mu.m. Particular implementations of the targets are free standing. The targets have a number of disclosed shaped, including cones, pyramids, hemispheres, and capped structures. The present disclosure also provides arrays of such targets. Also provided are methods of forming targets, such as the disclosed targets, using lithographic techniques, such as photolithographic techniques. In particular examples, a target mold is formed from a silicon wafer and then one or more sides of the mold are coated with a target material, such as one or more metals.

ICF target technology at the Russian Federal Nuclear Center

International Nuclear Information System (INIS)

Veselov, A.V.; Drozhin, V.S.; Druzhinin, A.A.; Izgorodin, V.M.; Iiyushechkin, B.N.; Kirillov, G.A.; Komleva, G.V.; Korochkin, A.M.; Medvedev, E.F.; Nikolaev, G.P.; Pikulin, I.V.; Pinegin, A.V.; Punin, V.T.; Romaev, V.N.; Sumatokhin, V.L.; Tarasova, N.N.; Tachaev, G.V.; Cherkesova, I.N.

1995-01-01

The main effort of the ICF target fabrication group is support of the experiments performed on the 'ISKRA-4' and 'ISKRA-5' laser systems. The main types of targets used in these experiments are direct drive, inverted corona, and indirect drive. For production of direct drive targets, manufacturing techniques have been developed for both hollow glass and polystyrene microspheres. Hollow glass microspheres are fabricated by free-fall of liquid glass drops or dry gel in a 4 meter vertical kiln. These methods allow us to manufacture glass microspheres with diameters from 50 μm to 1 mm, wall thicknesses from 0.5 to 10 μm, and aspect ratios (radius/ wall) from 20 to 500. The microspheres have a thickness inhomogeneity less than 5% and non-sphericity less than 1%. Polystyrene microspheres are fabricated from polystyrene particles with a blowing agent in a similar vertical kiln. Polystyrene microspheres are fabricated with diameter up to 800 μm and wall thicknesses from 1 to 10 μm. 15 refs., 8 figs

Fabrication of a nanocarrier system through self-assembly of plasma protein and its tumor targeting

International Nuclear Information System (INIS)

Gong Guangming; Zhi Feng; Wang Kaikai; Tang Xiaolei; Yuan Ahu; Zhao Lili; Ding Dawei; Hu Yiqiao

2011-01-01

Human serum albumin (HSA) nanoparticles hold great promise as a nanocarrier system for targeted drug delivery. The objective of this study was to explore the possibility of preparing size controllable albumin nanoparticles using the disulfide bond breaking reagent β-mercaptoethanol (β-ME). The results showed that the protein concentration and temperature had positive effects on the sizes of the albumin nanoparticles, while pH had a negative effect on the rate of nanoparticle formation. The addition of β-ME induced changes in HSA secondary structure and exposed the hydrophobic core of HSA, leading to the formation of nanoparticles. Human serum albumin nanoparticles could be internalized by MCF-7 cells and mainly accumulated in cytoplasm. After injection in tumor bearing mice, the HSA nanoparticles accumulated in tumor tissues, demonstrating the targeting ability of the nanoparticles. Therefore, human serum albumin can be fabricated into nanoparticles by breaking the disulfide bonds and these nanoparticles exhibit high tumor targeting ability. Human serum albumin nanoparticles could be ideal for the targeted delivery of pharmacologically active substances.

Design and fabrication of a CH/Al dual-layer perturbation target for hydrodynamic instability experiments in ICF

Energy Technology Data Exchange (ETDEWEB)

Tang, Jun [Shanghai Key Laboratory of Special Artificial Microstructure Materials and Technology, School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China); Xie, Zhiyong [Shanghai Institute of Laser Plasma, Shanghai 201800 (China); Du, Ai [Shanghai Key Laboratory of Special Artificial Microstructure Materials and Technology, School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China); Ye, Junjian [Shanghai Institute of Laser Plasma, Shanghai 201800 (China); Zhang, Zhihua; Shen, Jun [Shanghai Key Laboratory of Special Artificial Microstructure Materials and Technology, School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China); Zhou, Bin, E-mail: zhoubin863@tongji.edu.cn [Shanghai Key Laboratory of Special Artificial Microstructure Materials and Technology, School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China)

2014-04-15

Highlights: • Sinusoidal perturbed Al foil was prepared by single-point diamond turning. • Perturbed Al foil was measured by surface profiler and white light interferometer. • Perturbed Al foil and CH layer adhered with each other via a hot-press process. • Parameters and cross-section of the CH–Al perturbation target was characterized. - Abstract: A polystyrene (CH)/aluminum (Al) dual-layer perturbation target for hydrodynamic instability experiments in inertial confinement fusion (ICF) was designed and fabricated. The target was composed of a perturbed 40 μm Al foil and a CH layer. The detailed fabrication method consisted of four steps. The 40 μm Al foil was first prepared by roll and polish process; the perturbation patterns were then introduced on the surface of the Al foil by the single-point diamond turning (SPDT) technology; the CH layer was prepared via a simple method which called spin-coating process; finally, the CH layer was directly coated on the perturbation surface of Al foil by a hot-press process to avoid the use of a sticker and to eliminate the gaps between the CH layer and the Al foil. The parameters of the target, such as the perturbation wavelength (T) and perturbation amplitude (A), were characterized by a QC-5000 tool microscope, an alpha-step 500 surface profiler and a NT1100 white light interferometer. The results showed that T and A of the target were about 52 μm and 7.34 μm, respectively. Thickness of the Al foil (H1), thickness of the CH layer (H2), and cross-section of the dual-layer target were characterized by a QC-5000 tool microscope and a scanning electron microscope (SEM). H1 and H2 were about 40 μm and 15 μm, respectively, the cross-sectional photographs of the target showed that the CH layer and the Al foil adhered perfectly with each other.

Biased Target Ion Beam Deposition and Nanoskiving for Fabricating NiTi Alloy Nanowires

Science.gov (United States)

Hou, Huilong; Horn, Mark W.; Hamilton, Reginald F.

2016-12-01

Nanoskiving is a novel nanofabrication technique to produce shape memory alloy nanowires. Our previous work was the first to successfully fabricate NiTi alloy nanowires using the top-down approach, which leverages thin film technology and ultramicrotomy for ultra-thin sectioning. For this work, we utilized biased target ion beam deposition technology to fabricate nanoscale (i.e., sub-micrometer) NiTi alloy thin films. In contrast to our previous work, rapid thermal annealing was employed for heat treatment, and the B2 austenite to R-phase martensitic transformation was confirmed using stress-temperature and diffraction measurements. The ultramicrotome was programmable and facilitated sectioning the films to produce nanowires with thickness-to-width ratios ranging from 4:1 to 16:1. Energy dispersive X-ray spectroscopy analysis confirmed the elemental Ni and Ti make-up of the wires. The findings exposed the nanowires exhibited a natural ribbon-like curvature, which depended on the thickness-to-width ratio. The results demonstrate nanoskiving is a potential nanofabrication technique for producing NiTi alloy nanowires that are continuous with an unprecedented length on the order of hundreds of micrometers.

Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1993--September 30, 1994

Energy Technology Data Exchange (ETDEWEB)

Hoppe, M. [ed.

1995-04-01

On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. During the period, GA was assigned 17 tasks in support of the Inertial Confinement Fusion program and its laboratories. This year they achieved full production capabilities for the micromachining, dimensional characterization and gold plating of hohlraums. They fabricated and delivered 726 gold-plated mandrels of 27 different types to LLNL and 48 gold-plated mandrels of two different types to LANL. They achieved full production capabilities in composite capsule production ad delivered in excess of 240 composite capsules. They continuously work to improve performance and capabilities. They were also directed to dismantle, remove, and disposition all equipment at the previous contractor (KMSF) that had radioactive contamination levels low enough that they could be exposed to the general public without radiological constraints. GA was also directed to receive and store the tritium fill equipment. They assisted LANL in the development of techniques for characterization of opaque targets. They developed deuterated and UV-opaque polymers for use by the University of Rochester`s Laboratory for Laser Energetics (UR/LLE) and devised a triple-orifice droplet generator to demonstrate the controlled-mass nature of the microencapsulation process. The ICF program is anticipating experiments at NIF and the Omega Upgrade. Both facilities will require capsules containing layered D{sub 2} or D-T fuel. They continued engineering and assembly of equipment for a cryogenic target handling system for UR/LLE that will fill, transport, layer, and characterize targets filled with cryogenic deuterium or deuterium-tritium fuel, and insert these cryogenic targets into the OMEGA Upgrade target chamber for laser implosion experiments.

Inertial confinement fusion target component fabrication and technology development support: Annual report, October 1, 1993--September 30, 1994

International Nuclear Information System (INIS)

Hoppe, M.

1995-04-01

On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. During the period, GA was assigned 17 tasks in support of the Inertial Confinement Fusion program and its laboratories. This year they achieved full production capabilities for the micromachining, dimensional characterization and gold plating of hohlraums. They fabricated and delivered 726 gold-plated mandrels of 27 different types to LLNL and 48 gold-plated mandrels of two different types to LANL. They achieved full production capabilities in composite capsule production ad delivered in excess of 240 composite capsules. They continuously work to improve performance and capabilities. They were also directed to dismantle, remove, and disposition all equipment at the previous contractor (KMSF) that had radioactive contamination levels low enough that they could be exposed to the general public without radiological constraints. GA was also directed to receive and store the tritium fill equipment. They assisted LANL in the development of techniques for characterization of opaque targets. They developed deuterated and UV-opaque polymers for use by the University of Rochester's Laboratory for Laser Energetics (UR/LLE) and devised a triple-orifice droplet generator to demonstrate the controlled-mass nature of the microencapsulation process. The ICF program is anticipating experiments at NIF and the Omega Upgrade. Both facilities will require capsules containing layered D 2 or D-T fuel. They continued engineering and assembly of equipment for a cryogenic target handling system for UR/LLE that will fill, transport, layer, and characterize targets filled with cryogenic deuterium or deuterium-tritium fuel, and insert these cryogenic targets into the OMEGA Upgrade target chamber for laser implosion experiments

Conception and fabrication of innovative Am-Based targets: the ca mix/Cochix experiment

International Nuclear Information System (INIS)

Schmidt, N.; Croixmarie, Y.; Abonneau, E.; Ottaviani, J.P.; Donnet, L.; Desmouliere, F.; Konings, R.J.M.; Fernandez, A.

2003-01-01

A large experimental programme has been planned to be carried out in the French PHENIX reactor. The purpose is to evaluate the technical feasibility of minor actinide transmutation in fast reactors. Two major series of experiments have been designed for the heterogeneous transmutation mode. The first one, the MATINA (Matrices for Incineration of Actinides) series, aims at testing both different inert matrices in a fast flux and different concepts. The study is generic and focuses on the material behaviour under representative irradiation conditions. Targets are free of minor actinides to make the fabrication and design steps easier and faster. The second one, ECRIX, CAMIX (Compounds of Americium in PHENIX) and COCHIX (Concept Optimized microstructure in PHENIX), is a further step in the demonstration phase of the ''once-through'' transmutation and deals with Am-bearing targets irradiated in a fast neutron spectrum ''locally'' moderated. The moderator materials tested will be calcium hydride CaH 2-x (cases of ECRIX-H, CAMIX and COCHIX) and boron carbide 11 B 4 C (case of ECRIX-B) in order to accelerate the process of transmutation significantly. (author)

Pre-series and testing route for the serial fabrication of W7-X target elements

International Nuclear Information System (INIS)

Boscary, J.; Greuner, H.; Friedrich, T.; Traxler, H.; Mendelevitch, B.; Boeswirth, B.; Schlosser, J.; Smirnow, M.; Stadler, R.

2009-01-01

The fabrication of the actively cooled high-heat flux divertor of the WENDELSTEIN 7-X stellarator (W7-X) requires the delivery of 890 target elements, which are designed to withstand a stationary heat flux of 10 MW/m 2 . The organization of the manufacturing and testing route for the serial fabrication is the result of the pre-series activities. Flat CFC Sepcarb NB31 tiles are bonded to CuCrZr copper alloy cooling structure in consecutive steps. A copper layer is active metal cast to CFC tiles, and then an OF-copper layer is added by hot isostatic pressing to produce bi-layer tiles. These tiles are bonded by electron beam welding onto the cooling structure, which was manufactured independently. The introduction of the bi-layer technology proved to be a significant improvement of the bond reliability under thermal cycling loading. This result is also the consequence of the improved bond inspections throughout the manufacturing route performed in the ARGUS pulsed thermography facility of PLANSEE. The repairing process by electron beam welding of the bonding was also qualified. The extended pre-series activities related to the qualification of fabrication processes with the relevant non-destructive examinations aim to minimize the risks for the serial manufacturing and to guarantee the steady-state operation of the W7-X divertor.

Car Motivations in the Young Target Group: An International Perspective

Directory of Open Access Journals (Sweden)

Michael Bahles

2017-10-01

Full Text Available Globally, there are many profound changes going on within the automotive sector. There are new technological developments like e-mobility and autonomous cars, as well as new business models such as car sharing that may make purchasing a car obsolete for the younger, international target group. The intention of this paper is to identify the role and importance of cars in the young target group internationally and to explore current motives for buying an automobile. To this end, the authors conducted a psychological research study on a diverse group of upper division undergraduate and master’s degree level students originating from more than twenty different nations. Research methods used include structured one-on-one interviews and in-depth focus groups. The study’s results are useful for international marketing practitioners as they contribute to understanding the relevance and importance of automobiles for the international youth target market as well as identification of motives regarding car purchase across various countries. The results have implications for international managers within the automotive industry for the development of new mobility concepts as well as for international marketing communications within the automotive sector.

Targets development at Sandia National Laboratories

International Nuclear Information System (INIS)

Smith, M.L.; Hebron, D.; Derzon, M.; Olson, R.; Alberts, T.

1997-01-01

For many years, Sandia National Laboratories under contract to the Department of Energy has produced targets designed to understand complex ion beam and z-pinch plasma physics. This poster focuses on the features of target designs that make them suitable for Z-pinch plasma physics applications. Precision diagnostic targets will prove critical in understanding the plasma physics model needed for future ion beam and z-pinch design. Targets are designed to meet specific physics needs; in this case the authors have fabricated targets to maximize information about the end-on versus side-on x-ray emission and z-pinch hohlraum development. In this poster, they describe the fabrication and characterization techniques. They include discussion of current targets under development as well as target fabrication capabilities. Advanced target designs are fabricated by Sandia National Laboratories in cooperation with General Atomics of San Diego, CA and W.J. Schafer Associates, Inc. of Livermore, CA

Target support for inertial confinement fusion

International Nuclear Information System (INIS)

Schultz, K.R.

1995-08-01

General Atomics (GA) plays an important industrial support role for the US Inertial Confinement Fusion (ICF) program in the area of target technology. This includes three major activities: target fabrication support, target handling systems development, and target chamber design. The work includes target fabrication for existing ICF experiments, target and target system development for future experiments, and target research and target chamber design for experiments on future machines, such as the National Ignition Facility (NIF)

What the patient wants: Addressing patients' treatment targets in an integrative group psychotherapy programme.

Science.gov (United States)

Kealy, David; Joyce, Anthony S; Weber, Rainer; Ehrenthal, Johannes C; Ogrodniczuk, John S

2018-02-13

Limited empirical attention has been devoted to individualized treatment objectives in intensive group therapy for personality dysfunction. This study investigated patients' ratings of distress associated with individual therapy goals - referred to as target object severity - in an intensive Evening Treatment Programme for patients with personality dysfunction. Change in target objective severity was examined in a sample of 81 patients who completed treatment in an intensive, integrative group therapy programme. Correlation and regression analyses were used to examine associations between change in target object severity and patients' pre-treatment diagnosis, symptom distress, and treatment outcome expectancy, and between change in target objective severity and patients' ratings of group therapy process (group climate, therapeutic alliance, group cohesion). The relationship between change in target objective severity and longer-range life satisfaction was also examined in a subsample of patients who rated life satisfaction at follow-up. While change in target objective severity was not significantly related to pre-treatment variables, significant associations were found with several aspects of group therapy process. Patients' experience of a highly engaged group climate was uniquely associated with improvement in target object severity. Such improvement was significantly related to longer-term life satisfaction after controlling for general symptom change. The working atmosphere in group therapy contributes to patients' progress regarding individual treatment targets, and such progress is an important factor in later satisfaction. Attention to individualized treatment targets deserves further clinical and research attention in the context of integrative group therapy for personality dysfunction. This study found that patients attending an integrative group treatment programme for personality dysfunction experienced significant improvement in severity of distress

An Effort to Improve U Foil Fabrication Technology of Roll-casting for Fission Mo Target

Energy Technology Data Exchange (ETDEWEB)

Kim, Chang Kyu; Woo, Yun Myeong; Kim, Ki Hwan; Oh, Jong Myeong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Sim, Moon Soo [Chungnam University, Green Energy Technology, Daejeon (Korea, Republic of)

2010-10-15

Mo-99 isotope has been produced mainly by extracting fission products of {sup 235}U. The targets for irradiating in reactor have used as stainless tube coated with highly enriched UO{sub 2} at the inside surface and highly enriched UAlx plate cladded with aluminum. In connection with non-proliferation policy the RERTR program developed a new process of Mo-99 using low enriched uranium (LEU) instead of highly enriched uranium (HEU). LEU should be put about five times more quantity than HEU because the {sup 235}U contents of LEU and HEU are 20% and higher than 90%, respectively. Accordingly pure uranium metal foil target was adopted as a promising target material due to high uranium density. ANL and BATAN developed a Cintichem process using uranium metal foil target of 130 {mu}m in thickness jointly and the RERTR program is trying to disseminate the new process world-widely. However, uranium foil is made by lots of times rolling work on uranium plate, which is laborious and tedious. In order to avoid this difficulty KAERI developed a new process of making foil directly from uranium melt by roll casting. This process is very much simple, productive, and cost-effective. But the outside surface of foil is generally very rough. A typical transverse cross section had a minimum thickness of 65 {mu}m and a maximum thickness of 205 {mu}m. This roughness could affect (1) target fabrication, where the U foil, or the Ni foil might be damaged during drawing, and (2) irradiation behavior, where gaps between the target walls and the U metal might affect cooling of the target

Leadership Matters : The Effects of Targeted Killings on Militant Group Tactics

NARCIS (Netherlands)

Abrahms, Max; Mierau, Jochen

2017-01-01

Targeted killings have become a central component of counter-terrorism strategy. In response to the unprecedented prevalence of this strategy around the world, numerous empirical studies have recently examined whether "decapitating" militant groups with targeted killings is strategically effective.

Fabrication of the wing and vertical target dummy armour prototypes of the ITER divertor

Energy Technology Data Exchange (ETDEWEB)

Grattarola, M. E-mail: gratta@ari.ansaldo.it; Bet, M.; Biagiotti, B.; Gandini, G.; Merola, M.; Ottonello, G.B.; Riccardi, B.; Vieider, G.; Zacchia, F

2000-11-01

The dummy armour prototypes are identical to the reference components in terms of geometry, cooling circuit and material except for the armour material, which is replaced by an equivalent thickness of copper alloy. The main objectives of the dummy armour prototypes are the demonstration of the overall engineering concept of the Divertor, the integration in a 3 deg. cassette together with components manufactured by the other ITER Home Teams and the successive thermo-hydraulic tests on the whole Divertor module. This paper describes the realization of both the wing and the vertical target dummy armour prototypes focusing on the critical aspects of the fabrication and their impact on a further industrialization of the components.

Fabrication of the wing and vertical target dummy armour prototypes of the ITER divertor

International Nuclear Information System (INIS)

Grattarola, M.; Bet, M.; Biagiotti, B.; Gandini, G.; Merola, M.; Ottonello, G.B.; Riccardi, B.; Vieider, G.; Zacchia, F.

2000-01-01

The dummy armour prototypes are identical to the reference components in terms of geometry, cooling circuit and material except for the armour material, which is replaced by an equivalent thickness of copper alloy. The main objectives of the dummy armour prototypes are the demonstration of the overall engineering concept of the Divertor, the integration in a 3 deg. cassette together with components manufactured by the other ITER Home Teams and the successive thermo-hydraulic tests on the whole Divertor module. This paper describes the realization of both the wing and the vertical target dummy armour prototypes focusing on the critical aspects of the fabrication and their impact on a further industrialization of the components

From a target group towards interaction group: Alcohol prevention policy regarding young people in Germany

Directory of Open Access Journals (Sweden)

Susanne Linden

2015-10-01

Conclusion: Not only the content matters to promote participation, interactive communication, but also context and style of the communication. To enhance self reflection and deeper understanding it is essential to deliver the information in an attractive context, which has been found relevant for the target group. Just providing information may be important but is not sufficient in order to change the behaviour. Information which is elaborated through discussion – even online – may transform information into deeper understanding respectively knowledge. Thus it is more likely to have an impact on future behaviour. The target group should be recognized as interaction group. This will help to improve the adaptation and intervention continuously. Nevertheless, prevention and behaviour change will take their time and will need continuous effort at high level. Future research is needed to measure the impact of vivid discussion on people who take part in these discussions in an active way, compared to those who only follow the conversation thread.

Fabrication Method of the Mo-99 Target with Advanced Planar Flow Casting

International Nuclear Information System (INIS)

Sim, M. S.; Lee, J. H.; Kim, C. K.; Kim, W. J.

2011-01-01

Mo-99 is a parent isotope of Tc-99m for medical diagnosis and very significant owing to its large fraction over 80% of the whole demand of medical radioisotopes in the all countries. Mo-99 isotope has been produced mainly by 235 U which is extracting fission products. All the major providers of fission Mo have used HEU as a target material. But RERTR program that is nonproliferation policy encourages using HEU to LEU. KAERI has developed a processing to be able to produce a uranium foil continuously at one go. This processing gave an opportunity for LEU target using uranium foil to be commercialized. It correspond RERTR program. KAERI developed a new process of making foil directly from uranium melt by PFC. This process is simple, productive, and cost-effective. But the foil's air-side surface is generally very rough. A typical transverse cross section had a minimum thickness of 65 μm and a maximum thickness of 205 μm. This roughness could affect target fabrication and irradiation behavior. After issuing this problem KAERI launched a further effort since 2008. A new equipment was designed and manufactured in the industry in 2009. While the new equipment being test-operating, some occurrence of appearing problems appeared. Since 2010, Equipment was moved to KAERI, we performed many experiments using depleted uranium, and go get satisfied some results. We have got interesting results and manufactured uranium foil. A typical transverse cross section had a minimum thickness of 87 μm and a maximum thickness of 194 μm. The average thickness is 120 μm as a result of calculation

Recent Developments in Fabrication of Direct Drive Cylinder Targets for Hydrodynamics Experiments at the OMEGA Laser

International Nuclear Information System (INIS)

Nobile, A.; Balkey, M.M.; Bartos, J.J.; Batha, S.H.; Day, R.D.; Elliott, J.E.; Elliott, N.E.; Gomez, V.M.; Hatch, D.J.; Lanier, N.E.; Fincke, J.R.; Manzanares, R.; Pierce, T.H.; Sandoval, D.L.; Schmidt, D.W.; Steckle, W.P.

2004-01-01

Experimental campaigns are being conducted at the 60 beam OMEGA laser at the University of Rochester's Laboratory for Laser Energetics to acquire data to validate hydrodynamic models in the high energy-density regime. This paper describes targets that have been developed and constructed for these experimental campaigns. Targets are 860 μm inner diameter by 2.2 mm length cylinders with 70 μm thick polymer ablator. On the ablator inner surface and located halfway along the axis of the cylinder is a 500 μm wide Al marker band. Band thicknesses in the range 8-16 microns are used. CH foam with densities in the range 30-90 mg/cc fills the inside of the cylinder. While these targets have been fabricated for years, several new improvements and features have recently been developed. Improvements include the use of epoxy instead of polystyrene for the ablator, and the use of electrodeposited Al for the marker band. A critical feature of the target is the surface feature that is placed on the marker band. Experiments are aimed at understanding the hydrodynamic behavior of imploding cylinders as a function of this surface feature. Recent development work has focused on production of engineered surface features on the target marker band. Using a fast tool servo on a diamond turning lathe, a wide range of specified surface features have been produced. This paper will address improvements to the cylinder targets as well as current development efforts

Lysis of typhus-group rickettsia-infected targets by lymphokine activated killers

International Nuclear Information System (INIS)

Carl, M.; Dasch, G.A.

1986-01-01

The authors recently described a subset of OKT8, OKT3-positive lymphocytes from typhus-group rickettsia immune individuals which were capable of lysing autologous PHA-blasts or Epstein-Barr virus transformed B cells (LCL) infected with typhus-group rickettsiae. In order to determine if killing by these effectors was HLA-restricted, they stimulated peripheral blood mononuclear cells (PBMC) from typhus-group rickettsia immune individuals in vitro with typhus-group rickettsia-derived antigen for one week and then measured lysis of autologous LCL or HLA-mismatched LCL in a 4-6 hour Cr 51 -release assay. There was significant lysis of both the autologous and the HLA-mismatched infected targets as compared to the corresponding uninfected targets. Since this suggested that the effectors were lymphokine activated killers (LAK) rather than cytotoxic T lymphocytes, they then tested this hypothesis by stimulating PBMC from both immune and non-immune individuals in vitro for one week with purified interleukin 2 and measuring lysis of infected, autologous LCL. PBMC thus treated, from both immune and non-immune individuals, were capable of significantly lysing autologous, infected LCL as compared to the non-infected control. They therefore conclude that targets infected with typhus-group rickettsiae are susceptible to lysis to LAK

Global comparison of warring groups in 2002-2007: fatalities from targeting civilians vs. fighting battles.

Science.gov (United States)

Hicks, Madelyn Hsiao-Rei; Lee, Uih Ran; Sundberg, Ralph; Spagat, Michael

2011-01-01

Warring groups that compete to dominate a civilian population confront contending behavioral options: target civilians or battle the enemy. We aimed to describe degrees to which combatant groups concentrated lethal behavior into intentionally targeting civilians as opposed to engaging in battle with opponents in contemporary armed conflict. We identified all 226 formally organized state and non-state groups (i.e. actors) that engaged in lethal armed conflict during 2002-2007: 43 state and 183 non-state. We summed civilians killed by an actor's intentional targeting with civilians and combatants killed in battles in which the actor was involved for total fatalities associated with each actor, indicating overall scale of armed conflict. We used a Civilian Targeting Index (CTI), defined as the proportion of total fatalities caused by intentional targeting of civilians, to measure the concentration of lethal behavior into civilian targeting. We report actor-specific findings and four significant trends: 1.) 61% of all 226 actors (95% CI 55% to 67%) refrained from targeting civilians. 2.) Logistic regression showed actors were more likely to have targeted civilians if conflict duration was three or more years rather than one year. 3.) In the 88 actors that targeted civilians, multiple regressions showed an inverse correlation between CTI values and the total number of fatalities. Conflict duration of three or more years was associated with lower CTI values than conflict duration of one year. 4.) When conflict scale and duration were accounted for, state and non-state actors did not differ. We describe civilian targeting by actors in prolonged conflict. We discuss comparable patterns found in nature and interdisciplinary research. Most warring groups in 2002-2007 did not target civilians. Warring groups that targeted civilians in small-scale, brief conflict concentrated more lethal behavior into targeting civilians, and less into battles, than groups in larger

Description of ECRI (CNEA'S MTR fuel fabrication plant)

International Nuclear Information System (INIS)

Echenique, P.; Fabro, J.; Podesta, D.; Restelli, M.; Rossi, G.; Alvarez, L.; Adelfang, P.

2002-01-01

The ECRI Plant is dedicated to the development and fabrication of high-density fuel elements and targets for 99 Mo. In this sector had been done the start up Fuel Elements for the Reactors of Peru, Iran, Algeria and Egypt. All of them were made with U 3 O 8 . The targets for 99 Mo using HEU were fabricated too in the last years. The new material of high-density for Fuel Elements as U 3 Si 2 were done in this sector, three prototypes were fabricated, two are still under irradiation. (P06 and P07). As new developments we are working with U-Mo (7%) Fuel Plates with both material Korean and HMD. This work is under the RERTR Program and two fuel elements, manufactured by us, with both powders, will be irradiated in Petten. For 99 Mo targets, we are fabricating miniplates of LEU with an AlUx powder by pulvi-metallurgy technique. And it is under development the foils targets under the RERTR Program. A general view of the fabrication facilities and control sector will be shown. The different operations that are done in each sector will be explained. All our activities will be certified under the ISO 9000 and we are working hard to get it in the middle of 2003. (author)

Fabrication Method of the Mo-99 Target with Advanced Planar Flow Casting

Energy Technology Data Exchange (ETDEWEB)

Sim, M. S.; Lee, J. H. [Chungnam University, Green Energy Technology, Daejeon (Korea, Republic of); Kim, C. K.; Woo, Y. M. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2011-05-15

Mo-99 is a parent isotope of Tc-99m for medical diagnosis and very significant owing to its large fraction over 80% of the whole demand of medical radioisotopes in the all countries. Mo-99 isotope has been produced mainly by {sup 235}U which is extracting fission products. All the major providers of fission Mo have used HEU as a target material. But RERTR program that is non-proliferation policy encourages using HEU to LEU. KAERI has developed a processing to be able to produce a uranium foil continuously at one go. This processing gave an opportunity for LEU target using uranium foil to be commercialized. It correspond RERTR program. KAERI developed a new process of making foil directly from uranium melt by PFC. This process is simple, productive, and cost-effective. But the foil{center_dot}{center_dot}{center_dot}s air-side surface is generally very rough. A typical transverse cross section had a minimum thickness of 65 {mu}m and a maximum thickness of 205 {mu}m. This roughness could affect target fabrication and irradiation behavior. After issuing this problem KAERI launched a further effort since 2008. A new equipment was designed and manufactured in the industry in 2009. While the new equipment being test-operating, some occurrence of appearing problems appeared. Since 2010, Equipment was moved to KAERI, we performed many experiments using depleted uranium, and go get satisfied some results. We have got interesting results and manufactured uranium foil. A typical transverse cross section had a minimum thickness of 87 {mu}m and a maximum thickness of 194 {mu}m. However, the average thickness is 130 {mu}m as a result of measurement by a micrometer

Classification and Target Group Selection Based Upon Frequent Patterns

NARCIS (Netherlands)

W.H.L.M. Pijls (Wim); R. Potharst (Rob)

2000-01-01

textabstractIn this technical report , two new algorithms based upon frequent patterns are proposed. One algorithm is a classification method. The other one is an algorithm for target group selection. In both algorithms, first of all, the collection of frequent patterns in the training set is

Current progress in NIF target concepts

International Nuclear Information System (INIS)

Gobby, P.L.; Foreman, L.R.; Thoma, D.J.; Jacobson, L.A.; Hollis, R.V.; Barrera, J.; Mitchell, M.A.; Salazar, M.A.; Salzer, L.J.

1996-01-01

Target concepts for the National Ignition Facility (NIF) require progress in the art and science of target fabrication. Three distinct issues are addressed: beryllium fuel capsules, foam-buffered direct drive, and high-density gas-filled hohlraums. In all cases experiments on the existing Nova laser at LLNL are either in progress or planned for the near future to test the various concepts. Consequently, target fabrication must be able to deliver targets appropriate for each

Global comparison of warring groups in 2002-2007: fatalities from targeting civilians vs. fighting battles.

Directory of Open Access Journals (Sweden)

Madelyn Hsiao-Rei Hicks

Full Text Available BACKGROUND: Warring groups that compete to dominate a civilian population confront contending behavioral options: target civilians or battle the enemy. We aimed to describe degrees to which combatant groups concentrated lethal behavior into intentionally targeting civilians as opposed to engaging in battle with opponents in contemporary armed conflict. METHODOLOGY/PRINCIPAL FINDINGS: We identified all 226 formally organized state and non-state groups (i.e. actors that engaged in lethal armed conflict during 2002-2007: 43 state and 183 non-state. We summed civilians killed by an actor's intentional targeting with civilians and combatants killed in battles in which the actor was involved for total fatalities associated with each actor, indicating overall scale of armed conflict. We used a Civilian Targeting Index (CTI, defined as the proportion of total fatalities caused by intentional targeting of civilians, to measure the concentration of lethal behavior into civilian targeting. We report actor-specific findings and four significant trends: 1. 61% of all 226 actors (95% CI 55% to 67% refrained from targeting civilians. 2. Logistic regression showed actors were more likely to have targeted civilians if conflict duration was three or more years rather than one year. 3. In the 88 actors that targeted civilians, multiple regressions showed an inverse correlation between CTI values and the total number of fatalities. Conflict duration of three or more years was associated with lower CTI values than conflict duration of one year. 4. When conflict scale and duration were accounted for, state and non-state actors did not differ. We describe civilian targeting by actors in prolonged conflict. We discuss comparable patterns found in nature and interdisciplinary research. CONCLUSIONS/SIGNIFICANCE: Most warring groups in 2002-2007 did not target civilians. Warring groups that targeted civilians in small-scale, brief conflict concentrated more lethal

Heavy-ion targets

International Nuclear Information System (INIS)

Adair, H.L.; Kobisk, E.H.

1985-01-01

This chapter examines the characteristics of targets required in heavy-ion accelerator physics experiments. The effects of target parameters on heavy-ion experimental results are reviewed. The target fabrication and characterization techniques used to minimize experimental problems during heavy-ion bombardment are described. Topics considered include target thickness and uniformity, target lifetime, target purity, substrate materials, Doppler shift effects, metal preparations, and target preparation methods

HRP facility for fabrication of ITER vertical target divertor full scale plasma facing units

International Nuclear Information System (INIS)

Visca, Eliseo; Roccella, S.; Candura, D.; Palermo, M.; Rossi, P.; Pizzuto, A.; Sanguinetti, G.P.; Mancini, A.; Verdini, L.; Cacciotti, E.; Cerri, V.; Mugnaini, G.; Reale, A.; Giacomi, G.

2015-01-01

Highlights: • R&D activities for the manufacturing of ITER divertor high heat flux plasma-facing components (HHFC). • ENEA and Ansaldo have jointly manufactured several actively cooled monoblock mock-ups and prototypical components. • ENEA and ANSALDO NUCLEARE jointly participate to the European program for the qualification of the manufacturing technology for the ITER divertor IVT. • Successful manufacturing by HRP (Hot Radial Pressing) of first full-scale full-W armored IVT qualification prototype. - Abstract: ENEA and Ansaldo Nucleare S.p.A. (ANN) have being deeply involved in the European development activities for the manufacturing of the ITER Divertor Inner Vertical Target (IVT) plasma-facing components. During normal operation the heat flux deposited on the bottom segment of divertor is 5–10 MW/m 2 but the capability to remove up to 20 MW/m 2 during transient events of 10 s must also be demonstrated. In order to fulfill ITER requirements, ENEA has set up and widely tested a manufacturing process, named Hot Radial Pressing (HRP). The last challenge is now to fabricate full-scale prototypes of the IVT, aimed to be qualified for the next step, i.e. the series production. On the basis of the experience of manufacturing hundreds of small mock-ups, ENEA designed and installed a new suitable HRP facility. The objective of getting a final shaped plasma facing unit (PFU) that satisfies these requirements is an ambitious target because tolerances set by ITER/F4E are very tight. The setting-up of the equipment started with the fabrication of full scale and representative ‘dummies’ in which stainless steel instead of CFC or W was used for monoblocks. The results confirmed that dimensions were compliant with the required tolerances. The paper reports a brief description of the innovative HRP equipment and the dimensional check results after HRP of the first full-scale full-W PFU.

HRP facility for fabrication of ITER vertical target divertor full scale plasma facing units

Energy Technology Data Exchange (ETDEWEB)

Visca, Eliseo, E-mail: eliseo.visca@enea.it [Unità Tecnica Fusione, ENEA C. R. Frascati, via E. Fermi 45, IT-00044 Frascati (Roma) (Italy); Roccella, S. [Unità Tecnica Fusione, ENEA C. R. Frascati, via E. Fermi 45, IT-00044 Frascati (Roma) (Italy); Candura, D.; Palermo, M. [Ansaldo Nucleare S.p.A., Corso Perrone 25, IT-16152 Genova (Italy); Rossi, P.; Pizzuto, A. [Unità Tecnica Fusione, ENEA C. R. Frascati, via E. Fermi 45, IT-00044 Frascati (Roma) (Italy); Sanguinetti, G.P. [Ansaldo Nucleare S.p.A., Corso Perrone 25, IT-16152 Genova (Italy); Mancini, A.; Verdini, L.; Cacciotti, E.; Cerri, V.; Mugnaini, G.; Reale, A.; Giacomi, G. [Unità Tecnica Fusione, ENEA C. R. Frascati, via E. Fermi 45, IT-00044 Frascati (Roma) (Italy)

2015-10-15

Highlights: • R&D activities for the manufacturing of ITER divertor high heat flux plasma-facing components (HHFC). • ENEA and Ansaldo have jointly manufactured several actively cooled monoblock mock-ups and prototypical components. • ENEA and ANSALDO NUCLEARE jointly participate to the European program for the qualification of the manufacturing technology for the ITER divertor IVT. • Successful manufacturing by HRP (Hot Radial Pressing) of first full-scale full-W armored IVT qualification prototype. - Abstract: ENEA and Ansaldo Nucleare S.p.A. (ANN) have being deeply involved in the European development activities for the manufacturing of the ITER Divertor Inner Vertical Target (IVT) plasma-facing components. During normal operation the heat flux deposited on the bottom segment of divertor is 5–10 MW/m{sup 2} but the capability to remove up to 20 MW/m{sup 2} during transient events of 10 s must also be demonstrated. In order to fulfill ITER requirements, ENEA has set up and widely tested a manufacturing process, named Hot Radial Pressing (HRP). The last challenge is now to fabricate full-scale prototypes of the IVT, aimed to be qualified for the next step, i.e. the series production. On the basis of the experience of manufacturing hundreds of small mock-ups, ENEA designed and installed a new suitable HRP facility. The objective of getting a final shaped plasma facing unit (PFU) that satisfies these requirements is an ambitious target because tolerances set by ITER/F4E are very tight. The setting-up of the equipment started with the fabrication of full scale and representative ‘dummies’ in which stainless steel instead of CFC or W was used for monoblocks. The results confirmed that dimensions were compliant with the required tolerances. The paper reports a brief description of the innovative HRP equipment and the dimensional check results after HRP of the first full-scale full-W PFU.

Dynamic RCS Simulation of a Missile Target Group Based on the High-frequency Asymptotic Method

Directory of Open Access Journals (Sweden)

Zhao Tao

2014-04-01

Full Text Available To simulate dynamic Radar Cross Section (RCS of missile target group, an efficient RCS prediction approach is proposed based on the high-frequency asymptotic theory. The minimal energy trajectory and coordinate transformation is used to get trajectories of the missile, decoys and roll booster, and establish the dynamic scene for the separate procedure of the target group, and the dynamic RCS including specular reflection, edge diffraction and multi-reflection from the target group are obtained by Physical Optics (PO, Equivalent Edge Currents (EEC and Shooting-and-Bouncing Ray (SBR methods. Compared with the dynamic RCS result with the common interpolation method, the proposed method is consistent with the common method when the targets in the scene are far away from each other and each target is not sheltered by others in the incident direction. When the target group is densely distributed and the shelter effect can not be neglected, the interpolation method is extremely difficult to realize, whereas the proposed method is successful.

Tracking Maneuvering Group Target with Extension Predicted and Best Model Augmentation Method Adapted

Directory of Open Access Journals (Sweden)

Linhai Gan

2017-01-01

Full Text Available The random matrix (RM method is widely applied for group target tracking. The assumption that the group extension keeps invariant in conventional RM method is not yet valid, as the orientation of the group varies rapidly while it is maneuvering; thus, a new approach with group extension predicted is derived here. To match the group maneuvering, a best model augmentation (BMA method is introduced. The existing BMA method uses a fixed basic model set, which may lead to a poor performance when it could not ensure basic coverage of true motion modes. Here, a maneuvering group target tracking algorithm is proposed, where the group extension prediction and the BMA adaption are exploited. The performance of the proposed algorithm will be illustrated by simulation.

Web-based tailored lifestyle programs: exploration of the target group's interests and implications for practice.

NARCIS (Netherlands)

Verheijden, M.W.; Jans, M.P.; Hildebrandt, V.H.

2008-01-01

An important challenge in Web-based health promotion is to increase the reach of the target audience by taking the target groups' desires into consideration. Data from 505 members of a Dutch Internet panel (representative for Dutch Internet users) were used to asses the target group's interests and

Synthesis of the studies on fuels and transmutation targets (fabrication, design, irradiation damage and dissolution) realized in the framework of the Bataille law

International Nuclear Information System (INIS)

Pillon, S.

2004-12-01

This document presents the different studied fuels and targets for the transmutation of the minor actinides and of the long life fission products for PWR/EPR and Fast neutron Reactor/EFR of today technology; the results of studies on the behavior under ions irradiation and in experimental nuclear reactor; the knowledge in terms of design, simulation and sizing; the development in terms of fabrication; the knowledge on the dissolution aptitude of these fuels and targets. (A.L.B.)

Double-shell inertial confinement fusion target fabrication

International Nuclear Information System (INIS)

Hatcher, C.W.; Lorensen, L.E.; Weinstein, B.W.

1980-01-01

First generation hemishells, from which spherical shells are constructed, were fabricated by micromachining coated mandrels and by molding. The remachining of coated mandrels are described in detail. Techniques were developed for coating the microsized mandrels with polymeric and metallic materials by methods including conformal coating, vapor deposition, plasma polymerization and thermoforming. Micropositioning equipment and bonding techniques have also been developed to assemble the hemishells about a fuel pellet maintaining a spherical concentricity of better than 2 μm and voids in the hemishell bonding line of a few hundred angstroms or less

Fabrication and evaluation of tumor-targeted positive MRI contrast agent based on ultrasmall MnO nanoparticles.

Science.gov (United States)

Huang, Haitao; Yue, Tao; Xu, Ke; Golzarian, Jafar; Yu, Jiahui; Huang, Jin

2015-07-01

Gd(III) chelate is currently used as positive magnetic resonance imaging (MRI) contrast agent in clinical diagnosis, but generally induces the risk of nephrogenic systemic fibrosis (NSF) due to the dissociated Gd(3+) from Gd(III) chelates. To develop a novel positive MRI contrast agent with low toxicity and high sensitivity, ultrasmall MnO nanoparticles were PEGylated via catechol-Mn chelation and conjugated with cRGD as active targeting function to tumor. Particularly, the MnO nanoparticles with a size of ca. 5nm were modified by α,β-poly(aspartic acid)-based graft polymer containing PEG and DOPA moieties and, meanwhile, conjugated with cRGD to produce the contrast agent with a size of ca. 100nm and a longitudinal relaxivity (r1) of 10.2mM(-1)S(-1). Such nanoscaled contrast agent integrated passive- and active-targeting function to tumor, and its efficient accumulation behavior in tumor was verified by in vivo distribution study. At the same time, the PEG moiety played a role of hydrophilic coating to improve the biocompatibility and stability under storing and physiological conditions, and especially might guarantee enough circulation time in blood. Moreover, in vivo MRI revealed a good and long-term effect of enhancing MRI signal for as-fabricated contrast agent while cell viability assay proved its acceptable cytotoxicity for MRI application. On the whole, the as-fabricated PEGylated and cRGD-functionalized contrast agent based on ultrasmall MnO nanoparticles showed a great potential to the T1-weighted MRI diagnosis of tumor. Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.

Inertial confinement fusion target component fabrication and technology development support. Annual report, October 1, 1994--September 30, 1995

International Nuclear Information System (INIS)

Hoppe, M.

1996-05-01

On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities of the period October 1, 1994 through September 30, 1995. During this period, GA was assigned 15 tasks in support of the Inertial Confinement Fusion program and its laboratories. A portion of the effort on these tasks included providing direct ''Onsite Support'' at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). The ICF program is anticipating experiments at the National Ignition Facility (NIF) and the OMEGA Upgrade. Both facilities will require capsules containing layered D 2 or deuterium-tritium (D-T) fuel. The authors are part of the National Cryogenic Target Program to create and demonstrate viable ways to generate and characterize cryogenic layers. Progress has been made on ways to both create viable layers and to characterize them. They continued engineering, assembly and testing of equipment for a cryogenic target handling system for University of Rochester's Laboratory for Laser Energetics (UR/LLE) that will fill, transport, layer, and characterize targets filled with cryogenic fuel, and insert these cryogenic targets into the OMEGA Upgrade target chamber for laser implosion experiments. This report summarizes and documents the technical progress made on these tasks

Inertial confinement fusion target component fabrication and technology development support. Annual report, October 1, 1994--September 30, 1995

Energy Technology Data Exchange (ETDEWEB)

Hoppe, M. [ed.

1996-05-01

On December 30, 1990, the US Department of Energy entered into a contract with General Atomics (GA) to be the Inertial Confinement Fusion (ICF) Target Component Fabrication and Technology Development Support contractor. This report documents the technical activities of the period October 1, 1994 through September 30, 1995. During this period, GA was assigned 15 tasks in support of the Inertial Confinement Fusion program and its laboratories. A portion of the effort on these tasks included providing direct ``Onsite Support`` at Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory (LANL), and Sandia National Laboratory Albuquerque (SNLA). The ICF program is anticipating experiments at the National Ignition Facility (NIF) and the OMEGA Upgrade. Both facilities will require capsules containing layered D{sub 2} or deuterium-tritium (D-T) fuel. The authors are part of the National Cryogenic Target Program to create and demonstrate viable ways to generate and characterize cryogenic layers. Progress has been made on ways to both create viable layers and to characterize them. They continued engineering, assembly and testing of equipment for a cryogenic target handling system for University of Rochester`s Laboratory for Laser Energetics (UR/LLE) that will fill, transport, layer, and characterize targets filled with cryogenic fuel, and insert these cryogenic targets into the OMEGA Upgrade target chamber for laser implosion experiments. This report summarizes and documents the technical progress made on these tasks.

Fabrication of targets for transmutation of americium : synthesis of inertial matrix by sol-gel method. Procedure study on the infiltration of a radioactive solutions

International Nuclear Information System (INIS)

Fernandez Carretero, A.

2002-01-01

Transmutation and incineration are innovative options in the management and disposal of fission products and actinides. nevertheless, the fabrication of targets for transmutation and incineration of actinides and fission products require a reconsideration of conventional processes (mechanical blending) and the development of new procedures compatible with the high activity of these materials. This work presents th R and D of a new fabrication method called INRAM (Infiltration of Radioactive Materials) based on the infiltration of an actinide solution in a porous non radiotoxic material in the form of a pellet (up to 12% An), or beads (up to 40% An) produced by sol-gel. The first method have been used for the fabrication of spinel (MgAl 2 O 4 ) targets containing 11% Am, which have been irradiated in HFR-Petten (358.4 full power days). Post-test burn-up calculations showed that at the end of the irradiation the initial Am-241 concentration was reduced to 4%. The fraction of the initial americum atoms that have been fissioned is 28%. The main advantage of the INRAM method is that matrices with low or zero activity can be fabricated and formed into the required shape in an unshielded facility. This method offers other advantages over conventional ones, such as the active wastes are reduced, is easy to automate, adoptable to telemanipulation and dust free, which facilitate operator intervention and minimise radiation exposure to the personal. In addition, the infiltrant needs only be present in liquid form, i. e. it could be transferred directly from the reprocessing plant for fabrication into targets without conversion into-solid form. In order to optimise the infiltration process in depth investigations of all important process parameters, e. g. infiltration kinetics and metal (pu, Am) concentration in the feed solution, and also on extensive study or powder metallurgy parameters for the preparation of high quality fuel pellets with a high density, have been made. In

Indium oxide co-doped with tin and zinc: A simple route to highly conducting high density targets for TCO thin-film fabrication

Science.gov (United States)

Saadeddin, I.; Hilal, H. S.; Decourt, R.; Campet, G.; Pecquenard, B.

2012-07-01

Indium oxide co-doped with tin and zinc (ITZO) ceramics have been successfully prepared by direct sintering of the powders mixture at 1300 °C. This allowed us to easily fabricate large highly dense target suitable for sputtering transparent conducting oxide (TCO) films, without using any cold or hot pressing techniques. Hence, the optimized ITZO ceramic reaches a high relative bulk density (˜ 92% of In2O3 theoretical density) and higher than the well-known indium oxide doped with tin (ITO) prepared under similar conditions. All X-ray diagrams obtained for ITZO ceramics confirms a bixbyte structure typical for In2O3 only. This indicates a higher solubility limit of Sn and Zn when they are co-doped into In2O3 forming a solid-solution. A very low value of electrical resistivity is obtained for [In2O3:Sn0.10]:Zn0.10 (1.7 × 10-3 Ω cm, lower than ITO counterpart) which could be fabricated to high dense ceramic target suing pressure-less sintering.

Footwear Supply Network Management for Specific Target Groups

OpenAIRE

Franchini, Valentina

2013-01-01

This research is a part of CoReNet (Customer-ORiented and Eco-friendly NETworks for healthy fashionable goods), an European 7th Framework Program project, whose objective is to implement innovative methods and tools to fulfil needs and expectations of specific target groups – elderly, obese, disabled and diabetic people – by improving the supply network structure of the European Textile, Clothing and Footwear Industry (TCFI) to produce small series of functional and fashionable clothes and fo...

Global Comparison of Warring Groups in 2002–2007: Fatalities from Targeting Civilians vs. Fighting Battles

Science.gov (United States)

Hicks, Madelyn Hsiao-Rei; Lee, Uih Ran; Sundberg, Ralph; Spagat, Michael

2011-01-01

Background Warring groups that compete to dominate a civilian population confront contending behavioral options: target civilians or battle the enemy. We aimed to describe degrees to which combatant groups concentrated lethal behavior into intentionally targeting civilians as opposed to engaging in battle with opponents in contemporary armed conflict. Methodology/Principal Findings We identified all 226 formally organized state and non-state groups (i.e. actors) that engaged in lethal armed conflict during 2002–2007: 43 state and 183 non-state. We summed civilians killed by an actor's intentional targeting with civilians and combatants killed in battles in which the actor was involved for total fatalities associated with each actor, indicating overall scale of armed conflict. We used a Civilian Targeting Index (CTI), defined as the proportion of total fatalities caused by intentional targeting of civilians, to measure the concentration of lethal behavior into civilian targeting. We report actor-specific findings and four significant trends: 1.) 61% of all 226 actors (95% CI 55% to 67%) refrained from targeting civilians. 2.) Logistic regression showed actors were more likely to have targeted civilians if conflict duration was three or more years rather than one year. 3.) In the 88 actors that targeted civilians, multiple regressions showed an inverse correlation between CTI values and the total number of fatalities. Conflict duration of three or more years was associated with lower CTI values than conflict duration of one year. 4.) When conflict scale and duration were accounted for, state and non-state actors did not differ. We describe civilian targeting by actors in prolonged conflict. We discuss comparable patterns found in nature and interdisciplinary research. Conclusions/Significance Most warring groups in 2002–2007 did not target civilians. Warring groups that targeted civilians in small-scale, brief conflict concentrated more lethal behavior into

Fabrication and characterisation of fluidic based memristor sensor for liquid with hydroxyl group

Directory of Open Access Journals (Sweden)

Nor Shahanim Mohamad Hadis

2017-06-01

Full Text Available Two types of memristor sensor were fabricated using two different TiO2 deposition methods of sputtering and sol-gel spin coating. The surface morphology of the sensors and the behaviour of the sensors were analysed by using scanning electron microscopy with energy dispersive x-ray system and I-V characterisation system respectively. The sensors were applied with liquid with hydroxyl group to check the capability of this sensor in sensing different concentration of hydroxyl ion inside the liquid. For that purpose, d-glucose liquid with four concentrations of 10mM, 20mM, 30mM and 40mM were chosen. The liquids dispensed onto the TiO2 surface to act as sensing material. The TiO2 surface was initially covered with polydimethylsiloxane to control the liquid. The sensing capability of the sensors was determined via the current-voltage measurement and off-on resistance ratio. The sensitivity of the sensors was analysed from the off-on resistance ratio analysis. Type II memristor sensor which was fabricated using sol-gel spin coating technique recorded high sensitivity of 120.65 (mM−1, while Type I sensor fabricated using the sputtering technique recorded low sensitivity of 0.035 (mM−1. However, SEM-EDX image illustrated that the sputtering technique produced more uniform TiO2 thin film than sol-gel spin coating technique with larger atomic number of oxygen through the sol-gel spin coating technique. This indicates Type II sensor that has large number of oxygen atom produced more reaction with hydroxyl ion inside the liquid. While, Type I sensor produced less reaction compared with Type II and thus produced smaller off-on resistance ratio. Keywords: Fluidic based memristor, Hydroxyl ion, I-V characteristics, Off-on resistance ratio

Fabrication of high specificity hollow mesoporous silica nanoparticles assisted by Eudragit for targeted drug delivery.

Science.gov (United States)

She, Xiaodong; Chen, Lijue; Velleman, Leonora; Li, Chengpeng; Zhu, Haijin; He, Canzhong; Wang, Tao; Shigdar, Sarah; Duan, Wei; Kong, Lingxue

2015-05-01

Hollow mesoporous silica nanoparticles (HMSNs) are one of the most promising carriers for effective drug delivery due to their large surface area, high volume for drug loading and excellent biocompatibility. However, the non-ionic surfactant templated HMSNs often have a broad size distribution and a defective mesoporous structure because of the difficulties involved in controlling the formation and organization of micelles for the growth of silica framework. In this paper, a novel "Eudragit assisted" strategy has been developed to fabricate HMSNs by utilising the Eudragit nanoparticles as cores and to assist in the self-assembly of micelle organisation. Highly dispersed mesoporous silica spheres with intact hollow interiors and through pores on the shell were fabricated. The HMSNs have a high surface area (670 m(2)/g), small diameter (120 nm) and uniform pore size (2.5 nm) that facilitated the effective encapsulation of 5-fluorouracil within HMSNs, achieving a high loading capacity of 194.5 mg(5-FU)/g(HMSNs). The HMSNs were non-cytotoxic to colorectal cancer cells SW480 and can be bioconjugated with Epidermal Growth Factor (EGF) for efficient and specific cell internalization. The high specificity and excellent targeting performance of EGF grafted HMSNs have demonstrated that they can become potential intracellular drug delivery vehicles for colorectal cancers via EGF-EGFR interaction. Copyright © 2014 Elsevier Inc. All rights reserved.

Functional groups grafted nonwoven fabrics for blood filtration-The effects of functional groups and wettability on the adhesion of leukocyte and platelet

Energy Technology Data Exchange (ETDEWEB)

Yang Chao [State Key Lab of Metal Matrix Composites, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240 (China); Cao Ye [Institute of Blood Transfusion, Chinese Academy of Medical Sciences and Peking Union Medical College, Chengdu 610081 (China); Sun Kang, E-mail: ksun@sjtu.edu.cn [State Key Lab of Metal Matrix Composites, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240 (China); Liu Jiaxin; Wang Hong [Institute of Blood Transfusion, Chinese Academy of Medical Sciences and Peking Union Medical College, Chengdu 610081 (China)

2011-01-15

In this work, the effects of grafted functional groups and surface wettability on the adhesion of leukocyte and platelet were investigated by the method of blood filtration. The filter materials, poly(butylene terephthalate) nonwoven fabrics bearing different functional groups including hydroxyl (OH), carboxyl (COOH), sulfonic acid group (SO{sub 3}H) and zwitterionic sulfobetaine group ({sup +}N((CH{sub 3}){sub 2})(CH{sub 2}){sub 3}SO{sub 3}{sup Circled-Minus }) with controllable wettability were prepared by UV radiation grafting vinyl monomers with these functional groups. Our results emphasized that both surface functional groups and surface wettability had significant effects on the adhesion of leukocyte and platelet. In the case of filter materials with the same wettability, leukocytes adhering to filter materials decreased in the order: the surface bearing OH only > the surface bearing both OH and COOH > the surface bearing sulfobetaine group > the surface bearing SO{sub 3}H, while platelets adhering to filter materials decreased as the following order: the surface bearing SO{sub 3}H > the surface bearing both OH and COOH > the surface bearing OH only > the surface bearing sulfobetaine group. As the wettability of filter materials increased, both leukocyte and platelet adhesion to filter materials declined, except that leukocyte adhesion to the surface bearing OH only remained unchanged.

Fabrication of superhydrophobic cotton fabrics using crosslinking polymerization method

Science.gov (United States)

Jiang, Bin; Chen, Zhenxing; Sun, Yongli; Yang, Huawei; Zhang, Hongjie; Dou, Haozhen; Zhang, Luhong

2018-05-01

With the aim of removing and recycling oil and organic solvent from water, a facile and low-cost crosslinking polymerization method was first applied on surface modification of cotton fabrics for water/oil separation. Micro-nano hierarchical rough structure was constructed by triethylenetetramine (TETA) and trimesoyl chloride (TMC) that formed a polymeric layer on the surface of the fabric and anchored Al2O3 nanoparticles firmly between the fabric surface and the polymer layer. Superhydrophobic property was further obtained through self-assembly grafting of hydrophobic groups on the rough surface. The as-prepared cotton fabric exhibited superoleophilicity in atmosphere and superhydrophobicity both in atmosphere and under oil with the water contact angle of 153° and 152° respectively. Water/oil separation test showed that the as-prepared cotton fabric can handle with various oil-water mixtures with a high separation efficiency over 99%. More importantly, the separation efficiency remained above 98% over 20 cycles of reusing without losing its superhydrophobicity which demonstrated excellent reusability in oil/water separation process. Moreover, the as-prepared cotton fabric possessed good contamination resistance ability and self-cleaning property. Simulation washing process test showed the superhydrophobic cotton fabric maintained high value of water contact angle above 150° after 100 times washing, indicating great stability and durability. In summary, this work provides a brand-new way to surface modification of cotton fabric and makes it a promising candidate material for oil/water separation.

Rapid fabrication and characterization of sine wave targets

International Nuclear Information System (INIS)

Day, R.D.; Armijo, E.; Gobby, P.; Hatch, D.; Rivera, G.; Salzer, L.; Townsend, J.

1997-01-01

The effect of surface perturbations on Inertial Confinement Fusion target performance is currently being researched at Los Alamos National Laboratory (LANL). These perturbations can cause hydrodynamic instabilities which in turn reduce the targets' yield. To systematically measure the growth of these instabilities requires targets to be produced which have perturbations of a known amplitude and spatial frequency. The authors have recently assembled hardware onto one of their diamond turning lathes which enables them to machine and measure these sine waves in about 15 minutes. This is a significant reduction in time from the two and one half hours required by the previous method. This paper discusses the hardware, how it works, and how well the system is working for them to produce these targets

[How do Prevention Projects Reach their Target Groups? Results of a Survey with Prevention Projects].

Science.gov (United States)

Brand, T; Böttcher, S; Jahn, I

2015-12-01

 The aim of this study was to assess methods used to access target groups in prevention projects funded within the prevention research framework by the German Federal Ministry of Education and Research.  A survey with prevention projects was conducted. Access strategies, communication channels, incentives, programme reach, and successful practical recruitment strategies were explored.  38 out of 60 projects took part in the survey. Most projects accessed their target group within structured settings (e. g., child day-care centers, schools, workplaces). Multiple communication channels and incentives were used, with written information and monetary incentives being used most frequently. Only few projects were able to report their programme reach adequately; programme reach was highest for programmes accessing the target groups in structured settings. The respondents viewed active recruitment via personal communication with the target group and key persons in the settings as the most successful strategy.  The paper provides an overview on recruitment strategies used in current preven-tion projects. More systematic research on programme reach is necessary. © Georg Thieme Verlag KG Stuttgart · New York.

Korea's nuclear public information experiences-target groups and communication strategies

International Nuclear Information System (INIS)

Chung, J.K.

1996-01-01

Why public information activities in Korea are needed is first explained. There are three basic reasons; 1) to secure necessary sites for construction of large nuclear facilities; such as nuclear power plants, radwaste management facilities, and nuclear fuel-cycle related facilities 2) to maintain a friendly relationship between the local communities and the nuclear industries, 3) to promote better understanding about the nation's peaceful nuclear programs to the various target groups. Categorization of target groups and messages are reviewed. By whom the public information programs are implemented is also explained. An orchestrated effort together with the third communicators is stressed. Basic philosophy of nuclear public information programs is introduced. A high-profile information campaign and a low-profile information campaign are explained. Particular information strategies suitable to Korean situation as examined. In addition, the Korean general public perception on nuclear energy is briefly introduced. Also, some real insights of anti-nuclear movement in Korea together with the arguments are reviewed. In conclusion, the paper stresses that nuclear arguments became no more technical matters but almost socio-political issues. (author)

Materials considerations in accelerator targets

International Nuclear Information System (INIS)

Peacock, H.B. Jr.; Iyer, N.C.; Louthan, M.R. Jr.

1994-01-01

Future nuclear materials production and/or the burn-up of long lived radioisotopes may be accomplished through the capture of spallation produced neutrons in accelerators. Aluminum clad-lead and/or lead alloys has been proposed as a spallation target. Aluminum was the cladding choice because of the low neutron absorption cross section, fast radioactivity decay, high thermal conductivity, and excellent fabricability. Metallic lead and lead oxide powders were considered for the target core with the fabrication options being casting or powder metallurgy (PM). Scoping tests to evaluate gravity casting, squeeze casting, and casting and swaging processes showed that, based on fabricability and heat transfer considerations, squeeze casting was the preferred option for manufacture of targets with initial core cladding contact. Thousands of aluminum clad aluminum-lithium alloy core targets and control rods for tritium production have been fabricated by coextrusion processes and successfully irradiated in the SRS reactors. Tritium retention in, and release from the coextruded product was modeled from experimental and operational data. Newly produced tritium atoms were trapped by lithium atoms to form a lithium tritide. The effective tritium pressure required for trap or tritide stability was the equilibrium decomposition pressure of tritium over a lithium tritide-aluminum mixture. The temperature dependence of tritium release was determined by the permeability of the cladding to tritium and the local equilibrium at the trap sites. The model can be used to calculate tritium release from aluminum clad, aluminum-lithium alloy targets during postulated accelerator operational and accident conditions. This paper describes the manufacturing technologies evaluated and presents the model for tritium retention in aluminum clad, aluminum-lithium alloy tritium production targets

Effect of positively charged particles on sputtering damage of organic electro-luminescent diodes with Mg:Ag alloy electrodes fabricated by facing target sputtering

Directory of Open Access Journals (Sweden)

Kouji Suemori

2017-04-01

Full Text Available We investigated the influence of the positively charged particles generated during sputtering on the performances of organic light-emitting diodes (OLEDs with Mg:Ag alloy electrodes fabricated by sputtering. The number of positively charged particles increased by several orders of magnitude when the target current was increased from 0.1 A to 2.5 A. When a high target current was used, many positively charged particles with energies higher than the bond energy of single C–C bonds, which are typically found in organic molecules, were generated. In this situation, we observed serious OLED performance degradation. On the other hand, when a low target current was used, OLED performance degradation was not observed when the number of positively charged particles colliding with the organic underlayer increased. We concluded that sputtering damage caused by positively charged particles can be avoided by using a low target current.

Advanced fuel fabrication

International Nuclear Information System (INIS)

Bernard, H.

1989-01-01

This paper deals with the fabrication of advanced fuels, such as mixed oxides for Pressurized Water Reactors or mixed nitrides for Fast Breeder Reactors. Although an extensive production experience exists for the mixed oxides used in the FBR, important work is still needed to improve the theoretical and technical knowledge of the production route which will be introduced in the future European facility, named Melox, at Marcoule. Recently, the feasibility of nitride fuel fabrication in existing commercial oxide facilities was demonstrated in France. The process, based on carbothermic reduction of oxides with subsequent comminution of the reaction product, cold pressing and sintering provides (U, Pu)N pellets with characteristics suitable for irradiation testing. Two experiments named NIMPHE 1 and 2 fabricated in collaboration with ITU, Karlsruhe, involve 16 nitride and 2 carbide pins, operating at a linear power of 45 and 73 kW/m with a smear density of 75-80% TD and a high burn-up target of 15 at%. These experiments are currently being irradiated in Phenix, at Marcoule. (orig.)

Development of a coating technique for inertial confinement fusion plastic targets

International Nuclear Information System (INIS)

Kubo, U.; Tsubakihara, H.

1986-01-01

Deuterated polystyrene as a target material offers several advantages over other polymers because of the following: (1) it is chemically and physically stable at ordinary conditions, (2) it can be easily formed into spherical shells, and (3) it has a very high fraction of D 2 /H 2 (above approx.99%). As in our previous studies, the fabrication method was basically a utilization of the emulsion technique. This method is well suited to mass-producing the polymer targets without microprocessing techniques. We have developed a fabrication method for single shell targets and an extension of this technique also enables us to fabricate double shell targets. This new method is faster and less labor intensive than previous techniques. The development of ICF experiments requires multilayer structure targets; we have developed, moreover, a new fabrication technique called the multicoating method. The polymer coating can be fabricated by the application of an emulsion technique. On the other hand, with metal coating, a nonelectroplating method was used, and nickel was employed as the coating metal. The thickness of the polymer coating layer can be controlled with the rotational speed of a stirrer in the emulsion. In the case of nickel coating, it is achieved by controlling the plating bath temperature and immersion time during the plating process. The experiment resulted in the development of a new technique for the fabrication of multilayer targets and low density, thick polymer-layer-coated targets

Target technologies for laser inertial confinement fusion: state-of-the-art and future perspective

International Nuclear Information System (INIS)

Zhang Lin; Du Kai

2013-01-01

Targets are physical base of the laser inertial confinement fusion (ICF) researches. The quality of the targets has extremely important influences on the reliabilities and degree of precision of the ICF experimental results. The characteristics of the ICF targets, such as complexity and microscale, high precision, determine that the target fabrication process must be a system engineering. This paper presents progresses on the fabrication technologies of ICF targets. The existing problem and the future needs of ICF target fabrication technologies are also discussed. (authors)

Acidic aqueous uranium electrodeposition for target fabrication

International Nuclear Information System (INIS)

Saliba-Silva, A.M.; Oliveira, E.T.; Garcia, R.H.L.; Durazzo, M.

2013-01-01

Direct irradiation of targets inside nuclear research or multiple purpose reactors is a common route to produce 99 Mo- 99m Tc radioisotopes. The electroplating of low enriched uranium over nickel substrate might be a potential alternative to produce targets of 235 U. The electrochemistry of uranium at low temperature might be beneficial for an alternative route to produce 99 Mo irradiation LEU targets. Electrodeposition of uranium can be made using ionic and aqueous solutions producing uranium oxide deposits. The performance of uranium electrodeposition is relatively low because a big competition with H 2 evolution happens inside the window of electrochemical reduction potential. This work explores possibilities of electroplating uranium as UO 2 2+ (Uranium-VI) in order to achieve electroplating uranium in a sufficient amount to be commercially irradiated in the future Brazilian RMB reactor. Electroplated nickel substrate was followed by cathodic current electrodeposition from aqueous UO 2 (NO 3 ) 2 solution. EIS tests and modeling showed that a film formed differently in the three tested cathodic potentials. At the lower level, (-1.8V) there was an indication of a double film formation, one overlaying the other with ionic mass diffusion impaired at the interface with nickel substrate as showed by the relatively lower admittance of Warburg component. (author)

A New Strategy to Reduce Influenza Escape: Detecting Therapeutic Targets Constituted of Invariance Groups

Directory of Open Access Journals (Sweden)

Julie Lao

2017-03-01

Full Text Available The pathogenicity of the different flu species is a real public health problem worldwide. To combat this scourge, we established a method to detect drug targets, reducing the possibility of escape. Besides being able to attach a drug candidate, these targets should have the main characteristic of being part of an essential viral function. The invariance groups that are sets of residues bearing an essential function can be detected genetically. They consist of invariant and synthetic lethal residues (interdependent residues not varying or slightly varying when together. We analyzed an alignment of more than 10,000 hemagglutinin sequences of influenza to detect six invariance groups, close in space, and on the protein surface. In parallel we identified five potential pockets on the surface of hemagglutinin. By combining these results, three potential binding sites were determined that are composed of invariance groups located respectively in the vestigial esterase domain, in the bottom of the stem and in the fusion area. The latter target is constituted of residues involved in the spring-loaded mechanism, an essential step in the fusion process. We propose a model describing how this potential target could block the reorganization of the hemagglutinin HA2 secondary structure and prevent viral entry into the host cell.

Electric properties and fabrication of IMI-O LB films containing the imidazole group

CERN Document Server

Yoo, S Y; Kwon, Y S; Park, J C

1999-01-01

We fabricated an IMI-O polymer containing an imidazole group that could form a complex structure between the monolayer and the metal ions at the air-water interface. Also, the monolayer behavior at the air-water interface and the electrical properties of metal-complexed Langmuir-Blodgett (LB) films were investigated by using Brewster angle microscopy (BAM) and current-voltage(I-V) measurements. The difference in the BAM images between the pure water and the aqueous metal ions is attributed to the interactions of the copolymers with the metal ions at the interface and the consequent change of the monolayer organization. In the I-V characteristics, the current for LB films with different metal ion depended on the quantity of the metal-ion complexed with the LB film due to the interaction between the metal ion and the IMI-O polymer.

Target fabrication using laser and spark erosion machining

International Nuclear Information System (INIS)

Clement, X.; Coudeville, A.; Eyharts, P.; Perrine , J.P.; Rouillard, R.

1981-11-01

Lasers and E.D.M. (electrical discharge machining) are both extremely useful tools for machining the small targets needed in inertial confinement studies. Lasers are currently used in a wide range of target problems and it appears that E.D.M. has a still wider range of applications for plane and spherical targets. The problems of material deformation and tool breaking are practically eliminated as the electrode and the machined part are not in mechanical contact. In comparison with laser micromachining E.D.M. offers: larger versatility with the possibility of new developments and applications; higher production speed for thin conducting materials; lower initial and operating costs; the processes are well controlled, reproducible and can be easily automated; the operation is safe without the dangers associted with lasers

Fabrication of Foam Shells for ICF Experiments

Science.gov (United States)

Czechowicz, D. G.; Acenas, O.; Flowers, J. S.; Nikroo, A.; Paguio, R. R.; Schroen, D. G.; Streit, J.; Takagi, M.

2004-11-01

The General Atomics/Schafer team has developed processes to fabricate foam shells targets suitable for ICF experiments. The two most common chemical systems used to produce foam shells have been resorcinol-formaldehyde (R/F) aerogel and divinylbenzene (DVB). Spherical targets have been made in the form of shells and beads having diameters ranging from approximately 0.5 mm to 4.0 mm, and having densities from approximately 100 mg/cc to 250 mg/cc. The work on R/F foam shells has been concentrated on 1) shell fabrication process improvement to obtain high yields ( ˜25%) and 2) depositing a reliable permeation barrier to provide shells for ongoing direct drive experiments at LLE. Development of divinylbenzene foam shells has been mainly directed towards Inertial Fusion Energy applications (at densities as low as 30 mg/cc) and recently for shells for experiments at LLE. Details of the relevant metrology and properties of these foams as well as the range of targets currently available will be discussed.

GEM-loaded magnetic albumin nanospheres modified with cetuximab for simultaneous targeting, magnetic resonance imaging, and double-targeted thermochemotherapy of pancreatic cancer cells.

Science.gov (United States)

Wang, Ling; An, Yanli; Yuan, Chenyan; Zhang, Hao; Liang, Chen; Ding, Fengan; Gao, Qi; Zhang, Dongsheng

2015-01-01

Targeted delivery is a promising strategy to improve the diagnostic imaging and therapeutic effect of cancers. In this paper, novel cetuximab (C225)-conjugated, gemcitabine (GEM)-containing magnetic albumin nanospheres (C225-GEM/MANs) were fabricated and applied as a theranostic nanocarrier to conduct simultaneous targeting, magnetic resonance imaging (MRI), and double-targeted thermochemotherapy against pancreatic cancer cells. Fe3O4 nanoparticles (NPs) and GEM co-loaded albumin nanospheres (GEM/MANs) were prepared, and then C225 was further conjugated to synthesize C225-GEM/MANs. Their morphology, mean particle size, GEM encapsulation ratio, specific cell-binding ability, and thermal dynamic profiles were characterized. The effects of discriminating different EGFR-expressing pancreatic cancer cells (AsPC-1 and MIA PaCa-2) and monitoring cellular targeting effects were assessed by targeted MRI. Lastly, the antitumor efficiency of double/C225/magnetic-targeted and nontargeted thermochemotherapy was compared with chemotherapy alone using 3-(4, 5-dimethyl-2-thiazolyl)-2,5-diphenyl-2H-tetrazolium bromide (MTT) and flow cytometry (FCM) assay. When treated with targeted nanospheres, AsPC-1 cells showed a significantly less intense MRI T2 signal than MIA PaCa-2 cells, while both cells had similar signal strength when incubated with nontargeted nanospheres. T2 signal intensity was significantly lower when magnetic and C225 targeting were combined, rather than used alone. The inhibitory and apoptotic rates of each thermochemotherapy group were significantly higher than those of the chemotherapy-alone groups. Additionally, both MTT and FCM analysis verified that double-targeted thermochemotherapy had the highest targeted killing efficiency among all groups. The C225-GEM/MANs can distinguish various EGFR-expressing live pancreatic cancer cells, monitor diverse cellular targeting effects using targeted MRI imaging, and efficiently mediate double-targeted thermochemotherapy

Fabrication of inert matrices for heterogeneous transmutation. EFTTRA-T2 (RAS 2) irradiation programme

International Nuclear Information System (INIS)

Boshoven, J.G.; Hein, H.; Konings, R.J.M.

1996-07-01

This report describes the fabrication of targets containing inert matrices for the heterogeneous transmutation of plutonium and minor actinides. These targets will be irradiated in the EFTTRA-T2 (RAS-2) irradiation programme. The selection, preparation and characterization of the inert matrices and fabrication and loading of the irradiation capsules are discussed. (orig.)

A new method of identifying target groups for pronatalist policy applied to Australia.

Directory of Open Access Journals (Sweden)

Mengni Chen

Full Text Available A country's total fertility rate (TFR depends on many factors. Attributing changes in TFR to changes of policy is difficult, as they could easily be correlated with changes in the unmeasured drivers of TFR. A case in point is Australia where both pronatalist effort and TFR increased in lock step from 2001 to 2008 and then decreased. The global financial crisis or other unobserved confounders might explain both the reducing TFR and pronatalist incentives after 2008. Therefore, it is difficult to estimate causal effects of policy using econometric techniques. The aim of this study is to instead look at the structure of the population to identify which subgroups most influence TFR. Specifically, we build a stochastic model relating TFR to the fertility rates of various subgroups and calculate elasticity of TFR with respect to each rate. For each subgroup, the ratio of its elasticity to its group size is used to evaluate the subgroup's potential cost effectiveness as a pronatalist target. In addition, we measure the historical stability of group fertility rates, which measures propensity to change. Groups with a high effectiveness ratio and also high propensity to change are natural policy targets. We applied this new method to Australian data on fertility rates broken down by parity, age and marital status. The results show that targeting parity 3+ is more cost-effective than lower parities. This study contributes to the literature on pronatalist policies by investigating the targeting of policies, and generates important implications for formulating cost-effective policies.

A new method of identifying target groups for pronatalist policy applied to Australia

Science.gov (United States)

Chen, Mengni; Lloyd, Chris J.

2018-01-01

A country’s total fertility rate (TFR) depends on many factors. Attributing changes in TFR to changes of policy is difficult, as they could easily be correlated with changes in the unmeasured drivers of TFR. A case in point is Australia where both pronatalist effort and TFR increased in lock step from 2001 to 2008 and then decreased. The global financial crisis or other unobserved confounders might explain both the reducing TFR and pronatalist incentives after 2008. Therefore, it is difficult to estimate causal effects of policy using econometric techniques. The aim of this study is to instead look at the structure of the population to identify which subgroups most influence TFR. Specifically, we build a stochastic model relating TFR to the fertility rates of various subgroups and calculate elasticity of TFR with respect to each rate. For each subgroup, the ratio of its elasticity to its group size is used to evaluate the subgroup’s potential cost effectiveness as a pronatalist target. In addition, we measure the historical stability of group fertility rates, which measures propensity to change. Groups with a high effectiveness ratio and also high propensity to change are natural policy targets. We applied this new method to Australian data on fertility rates broken down by parity, age and marital status. The results show that targeting parity 3+ is more cost-effective than lower parities. This study contributes to the literature on pronatalist policies by investigating the targeting of policies, and generates important implications for formulating cost-effective policies. PMID:29425220

Evaluation of magnetostrictive composite coated fabric as a fragment barrier material

International Nuclear Information System (INIS)

Son, Kwon Joong; Fahrenthold, Eric P

2012-01-01

Over the last decade a surge in fragment barrier research has led to investigation of numerous materials and material augmentations in the attempt to improve the ballistic performance of systems designed to protect personnel, vehicles or infrastructure from impact and blast loads. One widely studied material augmentation approach is the use of coatings, often polymers, to enhance the performance of protection systems constructed from metal, concrete, composite and fabric materials. In recent research the authors have conducted the first experimental study of the ballistic performance of fabrics coated with a magnetically responsive polymer. Zero field impact experiments on coated fabric targets showed a 61% increase in impact energy dissipation, although the coated targets were not competitive with neat fabrics on a protection per unit mass basis. Under an applied field of 110 kA m −1 , the ballistic performance of the coated fabric was reduced. The reduction in performance may be attributed to a reduction in material damping and an increase in material modulus for the magnetostrictive component of the coating. Analysis of the coated fabric response to magnetic preloads suggests that coating tensile stresses and coating–fabric interface stresses induced by the applied field may also adversely affect ballistic performance. (paper)

Minor Actinide Laboratory at JRC-ITU: Fuel fabrication facility

International Nuclear Information System (INIS)

Fernandez, A.; McGinley, J.; Somers, J.

2008-01-01

The Minor Actinide Laboratory (MA-lab) of the Institute for Transuranium Elements is a unique facility for the fabrication of fuels and targets containing minor actinides (MA). It is of key importance for research on Partitioning and Transmutation in Europe, as it is one of the only dedicated facilities for the fabrication of MA containing materials, either for property measurements or for the production of test pins for irradiation experiments. In this paper a detailed description of the MA-Lab facility and the fabrication processes developed to fabricate fuels and samples containing high content of minor actinides is given. In addition, experience gained and improvements are also outlined. (authors)

Materials considerations in accelerator targets

International Nuclear Information System (INIS)

Peacock, H. B. Jr.; Iyer, N. C.; Louthan, M. R. Jr.

1995-01-01

Future nuclear materials production and/or the burn-up of long lived radioisotopes may be accomplished through the capture of spallation produced neutrons in accelerators. Aluminum clad-lead and/or lead alloys has been proposed as a spallation target. Aluminum was the cladding choice because of the low neutron absorption cross section, fast radioactivity decay, high thermal conductivity, and excellent fabricability. Metallic lead and lead oxide powders were considered for the target core with the fabrication options being casting or powder metallurgy (PM). Scoping tests to evaluate gravity casting, squeeze casting, and casting and swaging processes showed that, based on fabricability and heat transfer considerations, squeeze casting was the preferred option for manufacture of targets with initial core cladding contact. Thousands of aluminum clad aluminum-lithium alloy core targets and control rods for tritium production have been fabricated by coextrusion processes and successfully irradiated in the SRS reactors. Tritium retention in, and release from, the coextruded product was modeled from experimental and operational data. The model assumed that tritium atoms, formed by the 6Li(n,a)3He reaction, were produced in solid solution in the Al-Li alloy. Because of the low solubility of hydrogen isotopes in aluminum alloys, the irradiated Al-Li rapidly became supersaturated in tritium. Newly produced tritium atoms were trapped by lithium atoms to form a lithium tritide. The effective tritium pressure required for trap or tritide stability was the equilibrium decomposition pressure of tritium over a lithium tritide-aluminum mixture. The temperature dependence of tritium release was determined by the permeability of the cladding to tritium and the local equilibrium at the trap sites. The model can be used to calculate tritium release from aluminum clad, aluminum-lithium alloy targets during postulated accelerator operational and accident conditions. This paper describes

Dynamic fabric phase sorptive extraction for a group of pharmaceuticals and personal care products from environmental waters.

Science.gov (United States)

Lakade, Sameer S; Borrull, Francesc; Furton, Kenneth G; Kabir, Abuzar; Marcé, Rosa Maria; Fontanals, Núria

2016-07-22

This paper describes for the first time the use of a new extraction technique, based on fabric phase sorptive extraction (FPSE). This new mode proposes the extraction of the analytes in dynamic mode in order to reduce the extraction time. Dynamic fabric phase sorptive extraction (DFPSE) followed by liquid chromatography-tandem mass spectrometry was evaluated for the extraction of a group of pharmaceuticals and personal care products (PPCPs) from environmental water samples. Different parameters affecting the extraction were optimized and best conditions were achieved when 50mL of sample at pH 3 was passed through 3 disks and analytes retained were eluted with 10mL of ethyl acetate. The recoveries were higher than 60% for most of compounds with the exception of the most polar ones (between 8% and 38%). The analytical method was validated with environmental samples such as river water and effluent and influent wastewater, and good performance was obtained. The analysis of samples revealed the presence of some PPCPs at low ngL(-1) concentrations. Copyright © 2016 Elsevier B.V. All rights reserved.

Electrochemical properties of polyolefin nonwoven fabric modified with carboxylic acid group for battery separator

Energy Technology Data Exchange (ETDEWEB)

Choi, Seong-Ho; Kang, Hae-Jeong; Ryu, Eun-Nyoung; Lee, Kwang-Pill E-mail: kplee@kyungpook.ac.kr

2001-07-01

Carboxylic acid group was introduced by radiation-induced grafting of acrylic acid (AAc) onto polyolefine nonwoven fabric (PNF), wherein the PNF comprises at least about 60% of a polyethylene having a melting temperature at {approx}132 deg. C and no more than about 40% of a second polypropylene having a lower melting temperature at {approx}162 deg. C, for a battery separator. The AAc-grafted PNF was characterized by XPS, SEM, DSC, TGA and porosimeter. The wetting speed, electrolyte retention, electrical resistance, and tensile strength were evaluated after grafting of AAc. It was found that the wetting speed, electrolyte retention, thickness, and ion-exchange capacity increased, whereas the electrical resistance decreased with increasing grafting yield. The tensile strength decreased with increasing grafting yield, whereas the elongation decreased with increasing grafting yield. (author)

Electrochemical properties of polyolefine nonwoven fabric modified with carboxylic acid group for battery separator

Energy Technology Data Exchange (ETDEWEB)

Choi, Seong-Ho; Park, Keung-Shik; Kang, Hae-Jeong; Ryu, Eun-Nyoung; Lee, Pill-Kwang [Department of Chemistry Graduate School, Kyungpook National University, Taegu (Korea)

2000-07-01

Carboxylic acid group was introduced by radiation-induced grafting of acrylic acid (AAc) onto polyolefine nonwoven fabric (PNF), wherein the PNF comprises at least about 60% of a polyethylene having a melting temperature at {approx}132degC and no more than about 40% of a second polypropylene having a lower melting temperature at {approx}162degC, for a battery separator. The AAc-grafted PNF was characterized by XPS, SEM, DSC, TGA and porosimeter. The wetting speed, electrolyte retention, electrical resistance, and tensile strength were evaluated after grafting of AAc. It was found that the wetting speed, electrolyte retention, thickness, and ion-exchange capacity increased, whereas the electrical resistance decreased with increasing grafting yield. The tensile strength decreased with increasing grafting yield, whereas the elongation decreased with increasing grafting yield. (author)

Gentrification and community fabric in Chicago.

Science.gov (United States)

Betancur, John

2011-01-01

Critical authors of gentrification point to its deleterious impacts on displaced residents. Research on the nature or actual forms of impacts has not advanced much, however. This paper attempts to specify impacts on low-income racial/ethnic groups (Latinos in particular) in five Chicago neighbourhoods, with a particular focus on neighbourhood-based fabrics of support and advancement. Limited in their mobility and exchange value resources, lower-income groups depend on such fabrics far more than do the higher income. In fact, they have fewer choices and are most vulnerable to place-based shifts. The case seems especially challenging for minorities who, like European immigrants before them, depend largely on place-based platforms/social fabrics but, unlike them, confront the added factors of race and urban restructuring.

A New Invention Method to Determine the Reduction Factor for Low Fabric Tension Properties for Head Garment Fabrication

Directory of Open Access Journals (Sweden)

Aiman A.F

2016-01-01

Full Text Available This paper proposes a new method to determine the reduction factor for producing a head garment with specified targeted pressure output. Pressure garment fabric mostly supplied to the local hospitals with no information of the material properties and the fabrication method generally used a single reduction factor at various body segments. Reduction factor defined as the percentage of reducing the garment size from the original circumference of the body part which contributes to the compression. The objective of this study is to compare the fabrication method of head garment using reduction factor equation from previous research with the new proposed method. The equation to predict the reduction factor requires the parameter of the fabric tension which is obtained from tensile test and radius of curvature of the human body parts. In the new proposed method, a 3D scanning was used for data acquisition to obtain the geometry of the head area. The pressure outputs are measured by a pressure measurement system developed from Flexiforce sensor and Arduino circuit board. By using the equation, the result shows the calculated reduction factor produced an extremely tight head garment compared to the conducted experiments which manage to produce an adequate reduction factor with a targeted pressure output of 20mmHg. The result of the experiment indicates that the reduction factor ranging from 17% to 23% compared to the equation which produces 20% to 47% of reduction factor. As an additional, the proposed experimental method can be used for different type of pressure garment fabrics in order to obtain the relationship between the reduction factor and the circumference of the body parts.

Who uses apps in health promotion? A target group analysis of leaders.

Science.gov (United States)

Bregenzer, Anita; Wagner-Hartl, Verena; Jiménez, Paul

2017-11-01

User characteristics should be considered when designing features for e-health or m-health applications, as the developed solution should aim to support this specific target group. This study explores the effect of user characteristics (personality, health state, stress/recovery state, leadership behavior) on the interest and likelihood of using an app for health promotion activities at the workplace. Leaders are a key factor for the success of workplace health promotion; therefore, the target group of this study are leaders. The data of 412 leaders were collected in an online study. Hierarchical multiple linear regression analyses were conducted for four outcome criteria ("personal health," "contacting," "leadership feedback" and "corporate key figures"). The findings showed that neuroticism, physical health and health-promoting leadership were important predictors for using an app for monitoring personal health and getting in social contact about health issues. The stress/recovery state was significantly related to the feature of getting in social contact.

Influence of controlled and uncontrolled interventions on Twitter in different target groups

NARCIS (Netherlands)

Maanen, P.P. van; Aarts, O.; Boertjes, E.; Wijn, R.

2013-01-01

In this paper the influence of interventions on Twitter users is studied. We define influence in a) number of participants, b) size of the audience, c) amount of activity, and d) reach. Influence is studied for four different target groups: a) politicians, b) journalists, c) employees and d) the

The political logic of labour market reforms and popular images of target groups

DEFF Research Database (Denmark)

Larsen, Christian Albrekt

2008-01-01

Even though the shift from ‘passive' to ‘active' labour market policy exhibit large cross-national variations, they all seem to share two common characteristics; 1) the first group exposed to the new policies and the group exposed to the harshest policies was young people on social assistance and...... explanation for the different popular images of target groups and 2) by showing - using a national Australian sample - that these general popular images influence the way the public wants ‘active' labour market policy to be conducted....

MOX fuel fabrication at AECL

International Nuclear Information System (INIS)

Dimayuga, F.C.; Jeffs, A.T.

1995-01-01

Atomic Energy of Canada Limited's mixed-oxide (MOX) fuel fabrication activities are conducted in the Recycle Fuel Fabrication Laboratories (RFFL) at the Chalk River Laboratories. The RFFL facility is designed to produce experimental quantities of CANDU MOX fuel for reactor physics tests or demonstration irradiations. From 1979 to 1987, several MOX fuel fabrication campaigns were run in the RFFL, producing various quantities of fuel with different compositions. About 150 bundles, containing over three tonnes of MOX, were fabricated in the RFFL before operations in the facility were suspended. In late 1987, the RFFL was placed in a state of active standby, a condition where no fuel fabrication activities are conducted, but the monitoring and ventilation systems in the facility are maintained. Currently, a project to rehabilitate the RFFL and resume MOX fuel fabrication is nearing completion. This project is funded by the CANDU Owners' Group (COG). The initial fabrication campaign will consist of the production of thirty-eight 37-element (U,Pu)O 2 bundles containing 0.2 wt% Pu in Heavy Element (H.E.) destined for physics tests in the zero-power ZED-2 reactor. An overview of the Rehabilitation Project will be given. (author)

Micromechanical Structures Fabrication; FINAL

International Nuclear Information System (INIS)

Rajic, S

2001-01-01

Work in materials other than silicon for MEMS applications has typically been restricted to metals and metal oxides instead of more ''exotic'' semiconductors. However, group III-V and II-VI semiconductors form a very important and versatile collection of material and electronic parameters available to the MEMS and MOEMS designer. With these materials, not only are the traditional mechanical material variables (thermal conductivity, thermal expansion, Young's modulus, etc.) available, but also chemical constituents can be varied in ternary and quaternary materials. This flexibility can be extremely important for both friction and chemical compatibility issues for MEMS. In addition, the ability to continually vary the bandgap energy can be particularly useful for many electronics and infrared detection applications. However, there are two major obstacles associated with alternate semiconductor material MEMS. The first issue is the actual fabrication of non-silicon micro-devices and the second impediment is communicating with these novel devices. We have implemented an essentially material independent fabrication method that is amenable to most group III-V and II-VI semiconductors. This technique uses a combination of non-traditional direct write precision fabrication processes such as diamond turning, ion milling, laser ablation, etc. This type of deterministic fabrication approach lends itself to an almost trivial assembly process. We also implemented a mechanical, electrical, and optical self-aligning hybridization technique for these alternate-material MEMS substrates

Identifying policy target groups with qualitative and quantitative methods: the case of wildfire risk on nonindustrial private forest lands

Science.gov (United States)

A. Paige. Fischer

2012-01-01

Designing policies to harness the potential of heterogeneous target groups such as nonindustrial private forest owners to contribute to public policy goals can be challenging. The behaviors of such groups are shaped by their diverse motivations and circumstances. Segmenting heterogeneous target groups into more homogeneous subgroups may improve the chances of...

Evaluation of magnetorheological fluid augmented fabric as a fragment barrier material

International Nuclear Information System (INIS)

Son, Kwon Joong; Fahrenthold, Eric P

2012-01-01

The augmentation of high strength fabrics with non-Newtonian fluids has been suggested as a means for improving the ballistic performance of fragment barrier materials widely used in fan blade containment, body armor, orbital debris shielding, and other applications. Magnetorheological (MR) fluids have attracted particular interest, in view of their controllability and proven effectiveness in a variety of damping applications. In a basic research investigation of the MR fluid augmented fabric barrier concept, the authors have fabricated MR fluid saturated Kevlar targets and measured the ballistic performance of these targets both with and without an applied magnetic field. The experimental results show that magnetization of the MR fluid does, when considered in isolation, improve the ability of the augmented fabric to absorb impact energy. However, the benefits of plastic and viscous energy dissipation in the magnetized semi-solid are more than offset by the detrimental effects of yarn lubrication associated with the fluid’s hydrocarbon carrier. An analytical model developed to assist in the interpretation of the experimental data suggests that frictional interaction of the yarns is significantly more effective than magnetorheological augmentation of the fabric in distributing projectile loads away from the point of impact. (paper)

Development of fabric using chemically-treated sisal fibres

CSIR Research Space (South Africa)

Zwane, PE

2006-06-01

Full Text Available .875 total 1094.000 159 Resilience between groups 28.369 3 9.456 1.812 .147 within groups 814.125 156 5.219 total 842.494 159 Surf. cont. between groups 12.325 3 4.108 1.270 .287 within groups 504.650 156 3... will be discussed as seen in Table 6. The control fabric was highly rated as being harder, rougher, harsher and more open rather than soft, smooth, slippery and compact compared to all the other fabric types. For flexibility, extensibility, resiliency...

An Ethology of Urban Fabric(s)

DEFF Research Database (Denmark)

Fritsch, Jonas; Thomsen, Bodil Marie Stavning

2014-01-01

The article explores a non-metaphorical understanding of urban fabric(s), shifting the attention from a bird’s eye perspective to the actual, textural manifestations of a variety of urban fabric(s) to be studied in their real, processual, ecological and ethological complexity within urban life. We...... effectuate this move by bringing into resonance a range of intersecting fields that all deal with urban fabric(s) in complementary ways (interaction design and urban design activism, fashion, cultural theory, philosophy, urban computing)....

Inertial-confinement-fusion targets

International Nuclear Information System (INIS)

Hendricks, C.D.

1981-01-01

Inertial confinement fusion (ICF) targets are made as simple flat discs, as hollow shells or as complicated multilayer structures. Many techniques have been devised for producing the targets. Glass and metal shells are made by using drop and bubble techniques. Solid hydrogen shells are also produced by adapting old methods to the solution of modern problems. Some of these techniques, problems and solutions are discussed. In addition, the applications of many of the techniques to fabrication of ICF targets is presented

National Ignition Facility Target Chamber

International Nuclear Information System (INIS)

Wavrik, R W; Cox, J R; Fleming, P J

2000-01-01

On June 11, 1999 the Department of Energy dedicated the single largest piece of the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL) in Livermore, California. The ten (10) meter diameter aluminum target high vacuum chamber will serve as the working end of the largest laser in the world. The output of 192 laser beams will converge at the precise center of the chamber. The laser beams will enter the chamber in two by two arrays to illuminate 10 millimeter long gold cylinders called hohlraums enclosing 2 millimeter capsule containing deuterium, tritium and isotopes of hydrogen. The two isotopes will fuse, thereby creating temperatures and pressures resembling those found only inside stars and in detonated nuclear weapons, but on a minute scale. The NIF Project will serve as an essential facility to insure safety and reliability of our nation's nuclear arsenal as well as demonstrating inertial fusion's contribution to creating electrical power. The paper will discuss the requirements that had to be addressed during the design, fabrication and testing of the target chamber. A team from Sandia National Laboratories (SNL) and LLNL with input from industry performed the configuration and basic design of the target chamber. The method of fabrication and construction of the aluminum target chamber was devised by Pitt-Des Moines, Inc. (PDM). PDM also participated in the design of the chamber in areas such as the Target Chamber Realignment and Adjustment System, which would allow realignment of the sphere laser beams in the event of earth settlement or movement from a seismic event. During the fabrication of the target chamber the sphericity tolerances had to be addressed for the individual plates. Procedures were developed for forming, edge preparation and welding of individual plates. Construction plans were developed to allow the field construction of the target chamber to occur parallel to other NIF construction activities. This was

Cohort Profile: The Applied Research Group for Kids (TARGet Kids!).

Science.gov (United States)

Carsley, Sarah; Borkhoff, Cornelia M; Maguire, Jonathon L; Birken, Catherine S; Khovratovich, Marina; McCrindle, Brian; Macarthur, Colin; Parkin, Patricia C

2015-06-01

The Applied Research Group for Kids (TARGet Kids!) is an ongoing open longitudinal cohort study enrolling healthy children (from birth to 5 years of age) and following them into adolescence. The aim of the TARGet Kids! cohort is to link early life exposures to health problems including obesity, micronutrient deficiencies and developmental problems. The overarching goal is to improve the health of Canadians by optimizing growth and developmental trajectories through preventive interventions in early childhood. TARGet Kids!, the only child health research network embedded in primary care practices in Canada, leverages the unique relationship between children and families and their trusted primary care practitioners, with whom they have at least seven health supervision visits in the first 5 years of life. Children are enrolled during regularly scheduled well-child visits. To date, we have enrolled 5062 children. In addition to demographic information, we collect physical measurements (e.g. height, weight), lifestyle factors (nutrition, screen time and physical activity), child behaviour and developmental screening and a blood sample (providing measures of cardiometabolic, iron and vitamin D status, and trace metals). All data are collected at each well-child visit: twice a year until age 2 and every year until age 10. Information can be found at: http://www.targetkids.ca/contact-us/. © The Author 2014; all rights reserved. Published by Oxford University Press on behalf of the International Epidemiological Association.

Intrinsic ZnO films fabricated by DC sputtering from oxygen-deficient targets for Cu(In,Ga)Se2 solar cell application

Institute of Scientific and Technical Information of China (English)

Chongyin Yang; DongyunWan; Zhou Wang; Fuqiang Huang

2011-01-01

Intrinsic zinc oxide films, normally deposited by radio frequency (RF) sputtering, are fabricated by direct current (DC) sputtering. The oxygen-deficient targets are prepared via a newly developed double crucible method. The 800-nm-thick film obtaines significantly higher carrier mobility compareing with that of the 800-nm-thick ZnO film. This is achieved by the widely used RF sputtering, which favors the prevention of carrier recombination at the interfaces and reduction of the series resistance of solar cells. The optimal ZnO film is used in a Cu (In, Ga) Se2 (CIGS) solar cell with a high efficiency of 11.57%. This letter demonstrates that the insulating ZnO films can be deposited by DC sputtering from oxygen-deficient ZnO targets to lower the cost of thin film solar cells.%Intrinsic zinc oxide films,normally deposited by radio frequency (RF) sputtering,are fabricated by direct current (DC) sputtering.The oxygen-deficient targets are prepared via a newly developed double crucible method.The 800-nm-thick film obtaines significantly higher carrier mobility compareing with that of the 800-nm-thick ZnO film.This is achieved by the widely used RF sputtering,which favors the prevention of carrier recombination at the interfaces and reduction of the series resistance of solar cells.The optimal ZnO film is used in a Cu (In,Ga) Se2 (C1GS) solar cell with a high efficiency of 11.57％.This letter demonstrates that the insulating ZnO films can be deposited by DC sputtering from oxygen-deficient ZnO targets to lower the cost of thin film solar cells.High resistance transparent intrinsic zinc oxide (i-ZnO)thin film has been widely nsed as the front electrode in transparent electronics and photovoltaic devices because of its low cost and nontoxicity.Owing to its unique characteristics of high transparency and adjustable resistivity in a certain range,the use of i-ZnO thin films as diffusion barrier layers of a-Si/μc-Si,CdTe,and CIGS thin-film solar cells has been advantageous

Fabrication of 3D Silicon Sensors

Energy Technology Data Exchange (ETDEWEB)

Kok, A.; Hansen, T.E.; Hansen, T.A.; Lietaer, N.; Summanwar, A.; /SINTEF, Oslo; Kenney, C.; Hasi, J.; /SLAC; Da Via, C.; /Manchester U.; Parker, S.I.; /Hawaii U.

2012-06-06

Silicon sensors with a three-dimensional (3-D) architecture, in which the n and p electrodes penetrate through the entire substrate, have many advantages over planar silicon sensors including radiation hardness, fast time response, active edge and dual readout capabilities. The fabrication of 3D sensors is however rather complex. In recent years, there have been worldwide activities on 3D fabrication. SINTEF in collaboration with Stanford Nanofabrication Facility have successfully fabricated the original (single sided double column type) 3D detectors in two prototype runs and the third run is now on-going. This paper reports the status of this fabrication work and the resulted yield. The work of other groups such as the development of double sided 3D detectors is also briefly reported.

Materials processing in space: ICF target fabrication implications

International Nuclear Information System (INIS)

Hendricks, C.D.

1982-01-01

During the last quarter of 1982, the Novette laser will become operational at Lawrence Livermore National Laboratory. The primary characteristics of the Novette laser are shown. In many ways, the new laser will serve as a proving ground and test bed for the Nova laser which is also under construction and should be operational in early 1985. Tables provide the Nova operational characteristics. The advent of the two new lasers, Novette and Nova, will make it possible to study many new and exciting aspects of laser-target interactions and of many implosion physics experiments which have previously not been possible. Some of the most interesting and exciting work will be the exploration of the parameters critical to the ignition of a significant thermonuclear burn in the deuterium-tritium fuel in the targets

Fabricated Elastin.

Science.gov (United States)

Yeo, Giselle C; Aghaei-Ghareh-Bolagh, Behnaz; Brackenreg, Edwin P; Hiob, Matti A; Lee, Pearl; Weiss, Anthony S

2015-11-18

The mechanical stability, elasticity, inherent bioactivity, and self-assembly properties of elastin make it a highly attractive candidate for the fabrication of versatile biomaterials. The ability to engineer specific peptide sequences derived from elastin allows the precise control of these physicochemical and organizational characteristics, and further broadens the diversity of elastin-based applications. Elastin and elastin-like peptides can also be modified or blended with other natural or synthetic moieties, including peptides, proteins, polysaccharides, and polymers, to augment existing capabilities or confer additional architectural and biofunctional features to compositionally pure materials. Elastin and elastin-based composites have been subjected to diverse fabrication processes, including heating, electrospinning, wet spinning, solvent casting, freeze-drying, and cross-linking, for the manufacture of particles, fibers, gels, tubes, sheets and films. The resulting materials can be tailored to possess specific strength, elasticity, morphology, topography, porosity, wettability, surface charge, and bioactivity. This extraordinary tunability of elastin-based constructs enables their use in a range of biomedical and tissue engineering applications such as targeted drug delivery, cell encapsulation, vascular repair, nerve regeneration, wound healing, and dermal, cartilage, bone, and dental replacement. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Comparison of marginal and internal adaptation of copings fabricated from three different fabrication techniques: An in vitro study.

Science.gov (United States)

Arora, Aman; Yadav, Avneet; Upadhyaya, Viram; Jain, Prachi; Verma, Mrinalini

2018-01-01

The purpose of this study was to compare the marginal and internal adaptation of cobalt-chromium (Co-Cr) copings fabricated from conventional wax pattern, three-dimensional (3D)-printed resin pattern, and laser sintering technique. A total of thirty copings were made, out of which ten copings were made from 3D-printed resin pattern (Group A), ten from inlay wax pattern (Group B), and ten copings were obtained from direct metal laser sintering (DMLS) technique (Group C). All the thirty samples were seated on their respective dies and sectioned carefully using a laser jet cutter and were evaluated for marginal and internal gaps at the predetermined areas using a stereomicroscope. The values were then analyzed using one-way ANOVA test and post hoc Bonferroni test. One-way ANOVA showed lowest mean marginal discrepancy for DMLS and highest value for copings fabricated from inlay wax. The values for internal discrepancy were highest for DMLS (169.38) and lowest for 3D-printed resin pattern fabricated copings (133.87). Post hoc Bonferroni test for both marginal and internal discrepancies showed nonsignificant difference when Group A was compared to Group B ( P > 0.05) and significant when Group A was compared with Group C ( P < 0.05). Group B showed significant difference ( P < 0.05) when compared with Group C. Marginal and internal discrepancies of all the three casting techniques were within clinically acceptable values. Marginal fit of DMLS was superior as compared to other two techniques, whereas when internal fit was evaluated, conventional technique showed the best internal fit.

Fabrication of recyclable superhydrophobic cotton fabrics

Science.gov (United States)

Han, Sang Wook; Park, Eun Ji; Jeong, Myung-Geun; Kim, Il Hee; Seo, Hyun Ook; Kim, Ju Hwan; Kim, Kwang-Dae; Kim, Young Dok

2017-04-01

Commercial cotton fabric was coated with SiO2 nanoparticles wrapped with a polydimethylsiloxane (PDMS) layer, and the resulting material surface showed a water contact angle greater than 160°. The superhydrophobic fabric showed resistance to water-soluble contaminants and maintained its original superhydrophobic properties with almost no alteration even after many times of absorption-washing cycles of oil. Moreover, superhydrophobic fabric can be used as a filter to separate oil from water. We demonstrated a simple method of fabrication of superhydrophobic fabric with potential interest for use in a variety of applications.

Nanodiamond targets for accelerator X-ray experiments

Energy Technology Data Exchange (ETDEWEB)

Lobko, A., E-mail: lobko@inp.bsu.by [Research Institute for Nuclear Problems, 11 Bobrujskaya Str., Minsk 220030 (Belarus); Golubeva, E. [Belarusian State University, 4 Nezavisimosti Prosp., Minsk 220030 (Belarus); Kuzhir, P.; Maksimenko, S. [Research Institute for Nuclear Problems, 11 Bobrujskaya Str., Minsk 220030 (Belarus); Ryazan State RadioEngineering University, 59/1 Gagarina Street, Ryazan 390005 (Russian Federation); Paddubskaya, A. [Research Institute for Nuclear Problems, 11 Bobrujskaya Str., Minsk 220030 (Belarus); Shenderova, O. [International Technology Center, 8100 Brownleigh Dr., S. 120, Raleigh, NC 27617 (United States); Uglov, V. [Belarusian State University, 4 Nezavisimosti Prosp., Minsk 220030 (Belarus); Valynets, N. [Research Institute for Nuclear Problems, 11 Bobrujskaya Str., Minsk 220030 (Belarus)

2015-07-15

Results of fabrication of a nanodiamond target for accelerator X-ray experiments are reported. Nanodiamond film with dimensions 5 × 7 mm and thickness of 500 nm has been made of the high pressure high temperature nanodiamonds using a filtration method. The average crystallite size of primary nanodiamond particles varies around 100 nm. Source nanodiamonds and fabricated nanodiamond film were characterized using Raman spectroscopy, electron microscopy, and X-ray diffractometry. Preliminary results show that targets made of nanodiamonds are perspective in generating crystal-assisted radiation by the relativistic charged particles, such as parametric X-rays, diffracted transition radiation, diffracted Bremsstrahlung, etc.

Nanodiamond targets for accelerator X-ray experiments

International Nuclear Information System (INIS)

Lobko, A.; Golubeva, E.; Kuzhir, P.; Maksimenko, S.; Paddubskaya, A.; Shenderova, O.; Uglov, V.; Valynets, N.

2015-01-01

Results of fabrication of a nanodiamond target for accelerator X-ray experiments are reported. Nanodiamond film with dimensions 5 × 7 mm and thickness of 500 nm has been made of the high pressure high temperature nanodiamonds using a filtration method. The average crystallite size of primary nanodiamond particles varies around 100 nm. Source nanodiamonds and fabricated nanodiamond film were characterized using Raman spectroscopy, electron microscopy, and X-ray diffractometry. Preliminary results show that targets made of nanodiamonds are perspective in generating crystal-assisted radiation by the relativistic charged particles, such as parametric X-rays, diffracted transition radiation, diffracted Bremsstrahlung, etc

Target group segmentation makes sense: If one sheep leaps over the ditch, all the rest will follow

International Nuclear Information System (INIS)

Egmond, C.; Jonkers, R.; Kok, G.

2006-01-01

To meet the Dutch governmental goals of reducing CO 2 emission, target groups must increase their rates of adoption of energy conserving innovations. SenterNovem, in commission of the Dutch Ministry of Environmental Affairs, developed a strategy to effectively change the adoption behaviour of target groups. To develop strategies that take different rates of adoption into account, this study answers the questions: (1) How can different segments of the adopter market be categorized; (2) What are the characteristics of adopters in the different categories; (3) How do the determinants of behaviour of the adopter categories differ; and (4) What policy instruments can be used to change them? We conducted a secondary analysis of the data from a previous survey of housing associations. Based on the so-called self-designating method we constructed a scale of adoption rate and we measured the rate of adoption of housing associations. Segments of this target group with different adoption rates and correspondingly different characteristics were found: first adopters in a target group have a more visionary attitude, whereas the later adopters have a less visionary and more pragmatic attitude. We conclude that the self-designating method used in a survey provides explanation for the adoption speeds of different market segments. This explanation, in turn, can lead to more effective interventions

Power plant production of inertial confinement fusion targets

International Nuclear Information System (INIS)

Hendricks, C.D.; Johnson, W.L.

1979-01-01

Many of the current techniques for fabricating experimental targets appear to be directly extendable to the high-rate, low-cost production of reactor targets. This report describes several new techniques that, in conjunction with the expansion of existing techniques, can constitute a target factory. We have evaluated this concept on the basis of a generalized reactor target design and the projected specifications of reactor-grade targets

Group Targets Tracking Using Multiple Models GGIW-CPHD Based on Best-Fitting Gaussian Approximation and Strong Tracking Filter

Directory of Open Access Journals (Sweden)

Yun Wang

2016-01-01

Full Text Available Gamma Gaussian inverse Wishart cardinalized probability hypothesis density (GGIW-CPHD algorithm was always used to track group targets in the presence of cluttered measurements and missing detections. A multiple models GGIW-CPHD algorithm based on best-fitting Gaussian approximation method (BFG and strong tracking filter (STF is proposed aiming at the defect that the tracking error of GGIW-CPHD algorithm will increase when the group targets are maneuvering. The best-fitting Gaussian approximation method is proposed to implement the fusion of multiple models using the strong tracking filter to correct the predicted covariance matrix of the GGIW component. The corresponding likelihood functions are deduced to update the probability of multiple tracking models. From the simulation results we can see that the proposed tracking algorithm MM-GGIW-CPHD can effectively deal with the combination/spawning of groups and the tracking error of group targets in the maneuvering stage is decreased.

Effect of dopants and thermal treatment on properties of Ga-Al-ZnO thin films fabricated by hetero targets sputtering system

International Nuclear Information System (INIS)

Hong, JeongSoo; Matsushita, Nobuhiro; Kim, KyungHwan

2013-01-01

In this study, we fabricated Ga and Al doped ZnO (Ga-Al-ZnO; GAZO) thin films by using the facing targets sputtering system under various conditions such as input current and thermal treatment temperature. The properties of the as-deposited GAZO thin films were examined by four-point, UV/Vis spectrometry, X-ray diffraction, atomic force microscopy and field-emission scanning electron microscopy. The result showed that the lowest sheet resistance of the films was 59.3 ohm/sq and transmittance was about 85%. After thermal treatment, the properties of GAZO thin films were improved. The lowest sheet resistance (47.3 ohm/sq) of the GAZO thin films were obtained at thermal treatment temperature of 300 °C, considered to be the result of continuous substitutions by dopants and improved crystallinity by the thermal treatment. - Highlights: ► Ga and Al doped ZnO thin films were prepared by hetero targets sputtering system. ► Free electrons were increased due to the continuous substitutions of Ga and Al. ► Crystallinity was improved by recombination of particles with increasing of temperature

Laser ``M'egajoule'' cryogenic target program: from target fabrication to conformation of the deuterium-tritium ice layer

Science.gov (United States)

Collier, Rémy; Durut, Frédéric; Reneaume, Benoît; Chicane, Cédric; Théobald, Marc; Breton, Olivier; Martin, Michel; Fleury, Emmanuel; Vincent-Viry, Olivier; Bachelet, Franck; Jeannot, Laurent; Geoffray, Isabelle; Botrel, Ronan; Dauteuil, Christophe; Hermerel, Cyril; Choux, Alexandre; Bednarczyk, Sophie; Legaie, Olivier

2008-11-01

For the French inertial confinement fusion (ICF) experiments, cryogenic target assemblies (CTAs) for the LMJ program are manufactured and filled at CEA Valduc (Dijon) in the cryogenic targets filling station (IRCC). They will be moved at about 20 K into a transport cryostat for cryogenic targets and will be driven from CEA/Valduc to CEA/CESTA (Bordeaux). Cryogenic targets will then be transferred by several cryogenic grippers on the cryogenic target positioner before shots. The CTA has to meet severe specifications and involves a lot of challenging tasks for its manufacture. To fill CTAs by permeation with deuterium-tritium (DT), the IRCC need to meet strict thermal, mechanical and dimensional specifications. To obtain a good combustion yield, a very homogenous DT ice layer and very smooth roughness at 1.5 K below the DT triple point are also required. This paper deals with the up to date main issues in the different fields of the LMJ cryogenic target program.

Synthesis, processing and characterization of shear thickening fluid (STF) impregnated fabric composites

International Nuclear Information System (INIS)

Hassan, Tarig A.; Rangari, Vijay K.; Jeelani, Shaik

2010-01-01

Shear thickening is a non-Newtonian fluid behavior defined as the increase of viscosity with the increase in the applied shear rate. The shear thickening fluid (STF) is a combination of hard metal oxide particles suspended in a liquid polymer. This mixture of flowable and hard components at a particular composition, results in a material with remarkable properties. In this manuscript the shear thickening fluid (STF) was prepared by ultrasound irradiation of silica nanoparticles dispersed in liquid polyethylene glycol polymer. The as-prepared STFs have been tested for their rheological and thermal properties. Kevlar and Nylon fabrics were soaked in STF/ethanol solution to make STF/fabric composite. Knife threats and quasistatic penetration tests were performed on the neat fabrics and STF/fabric composite targets for both engineered spike and knife on areal density basis. The results showed that STF impregnated fabrics have better penetration resistance as compared to neat fabrics without affecting the fabric flexibility. This indicates that the addition of STF to the fabric have enhanced the fabric performance and can be used in liquid body armor applications.

Fuels and targets for incineration and transmutation of actinides: the ITU programme

International Nuclear Information System (INIS)

Fernandez, A.; Glatz, J.P.; Haas, D.; Konings, R.J.M.; Somers, J.; Toscano, E.; Walker, C.T.; Wegen, D.

2000-01-01

The ITU programme for the development of fuels and targets for transmutation of actinides is presented. The fabrication of various types of oxide fuels/targets by dust-free processes is described. Selected results of post-irradiation examinations of irradiation experiments (SUPERFACT, TRABANT-1, EFTTRA-T4) are presented to demonstrate the irradiation behaviour of these fuels/targets. Finally, the future developments at ITU in this field are described, including the new shielded facility (the MA lab) for fabrication of minor actinide fuels. (authors)

Fuels and targets for incineration and transmutation of actinides: the ITU programme

Energy Technology Data Exchange (ETDEWEB)

Fernandez, A.; Glatz, J.P.; Haas, D.; Konings, R.J.M.; Somers, J.; Toscano, E.; Walker, C.T.; Wegen, D. [Eurpean Commission, Joint Research Centre, Institute for Transuranium Elements, Kurlsruhe (Germany)

2000-07-01

The ITU programme for the development of fuels and targets for transmutation of actinides is presented. The fabrication of various types of oxide fuels/targets by dust-free processes is described. Selected results of post-irradiation examinations of irradiation experiments (SUPERFACT, TRABANT-1, EFTTRA-T4) are presented to demonstrate the irradiation behaviour of these fuels/targets. Finally, the future developments at ITU in this field are described, including the new shielded facility (the MA lab) for fabrication of minor actinide fuels. (authors)

Structure and properties of nanoparticles fabricated by laser ablation of Zn metal targets in water and ethanol

Science.gov (United States)

Svetlichnyi, V. A.; Lapin, I. N.

2013-10-01

Size characteristics, structure, and spectral and luminescent properties of nanoparticles fabricated by laser ablation of zinc metal targets in water and ethanol are experimentally investigated upon excitation by Nd:YAG-laser radiation (1064 nm, 7 ns, and 15 Hz). It is demonstrated that zinc oxide nanoparticles with average sizes of 10 nm (in water) and 16 nm (in ethanol) are formed in the initial stage as a result of ablation. The kinetics of the absorption and luminescence spectra, transmission electron microscopy, and x-ray structural analysis demonstrate that during long storage of water dispersions and their drying, nanoparticles efficiently interact with carbon dioxide gas of air that leads to the formation of water-soluble Zn(CO3)2(OH)6. In ethanol, Zn oxidation leads to the formation of stable dispersions of ZnO nanoparticles with 99% of the wurtzite phase; in this case, the fluorescence spectra of ZnO nanoparticles change with time, shifting toward longer wavelength region from 550 to 620 nm, which is caused by the changed nature of defects.

Constructing Risky Target Groups among Normal Citizens

DEFF Research Database (Denmark)

Møller, Marie Østergaard; Harrits, Gitte Sommer

Studies on social construction of target populations show how stereotypes and social categories transfer with experts, politicians and lawmakers from everyday life to the political system as ‘common sense knowledge’ about social problems and preferences for political categories. Here such categor......Studies on social construction of target populations show how stereotypes and social categories transfer with experts, politicians and lawmakers from everyday life to the political system as ‘common sense knowledge’ about social problems and preferences for political categories. Here...

Criteria for selection of target materials and design of high-efficiency-release targets for radioactive ion beam generation

CERN Document Server

Alton, G D; Liu, Y

1999-01-01

In this report, we define criteria for choosing target materials and for designing, mechanically stable, short-diffusion-length, highly permeable targets for generation of high-intensity radioactive ion beams (RIBs) for use at nuclear physics and astrophysics research facilities based on the ISOL principle. In addition, lists of refractory target materials are provided and examples are given of a number of successful targets, based on these criteria, that have been fabricated and tested for use at the Holifield Radioactive Ion Beam Facility (HRIBF).

Investigation of Micro Square Structure Fabrication by Applying Textured Cutting Tool in WEDM

Directory of Open Access Journals (Sweden)

Jianguo Zhang

2015-09-01

Full Text Available This paper studies micro structure fabrication by means of a textured tool cutting edge, which is manufactured by applying the wire cut electrical discharge machining (WEDM. Machining performance of the square structure fabrication on the tool cutting edge is investigated in the WEDM process, and the machining accuracy is explored in experimental analyses. In this proposed method, undesired overcut comes from the discharge between the processing debris and the side wall of the target structure. Furthermore, by applying the textured cutting tool, the target square structure is directly fabricated on the alumina workpiece with just a simple turning process, which verifies the feasibility of the proposed tool cutting edge textured method by applying the WEDM. This technology is expected to become a potential method for the mass production of micro structure surfaces in the future.

Fit of interim crowns fabricated using photopolymer-jetting 3D printing.

Science.gov (United States)

Mai, Hang-Nga; Lee, Kyu-Bok; Lee, Du-Hyeong

2017-08-01

The fit of interim crowns fabricated using 3-dimensional (3D) printing is unknown. The purpose of this in vitro study was to evaluate the fit of interim crowns fabricated using photopolymer-jetting 3D printing and to compare it with that of milling and compression molding methods. Twelve study models were fabricated by making an impression of a metal master model of the mandibular first molar. On each study model, interim crowns (N=36) were fabricated using compression molding (molding group, n=12), milling (milling group, n=12), and 3D polymer-jetting methods. The crowns were prepared as follows: molding group, overimpression technique; milling group, a 5-axis dental milling machine; and polymer-jetting group using a 3D printer. The fit of interim crowns was evaluated in the proximal, marginal, internal axial, and internal occlusal regions by using the image-superimposition and silicone-replica techniques. The Mann-Whitney U test and Kruskal-Wallis tests were used to compare the results among groups (α=.05). Compared with the molding group, the milling and polymer-jetting groups showed more accurate results in the proximal and marginal regions (P3D printing significantly enhanced the fit of interim crowns, particularly in the occlusal region. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

A triple axes multiple target holder assembly

International Nuclear Information System (INIS)

Tribedi, L.C.; Narvekar, S.D.; Pillay, R.G.; Tandon, P.N.

1993-01-01

We have designed and fabricated a rotatable target holder assembly capable of accommodating 27 targets. The target foils are mounted along two concentric circles on a ss wheel. On the outer circle 18 targets can be mounted each 20deg apart, and on the inner circle the remaining targets are positioned each 40deg apart. The self supporting or carbon backed targets are mounted on thin frames and are placed concentrically at the targets are mounted on thin frames and are placed concentrically at the target position on the wheel. Three degrees of freedom are provided to the target holder assembly. (author). 1 fig

Foil fabrication for the ROMANO event. Revision 1

International Nuclear Information System (INIS)

Romo, J.G. Jr.; Weed, J.W.; Griggs, G.E.; Brown, T.G.; Tassano, P.L.

1984-01-01

The Vacuum Processes Lab (VPL), of LLNL's M.E. Dept. - Material Fabrication Division (MFD), conducted various vacuum related support activities for the ROMANO nuclear physics experiment. This report focuses on the foil fabrication activities carried out between July and November 1983 for the ROMANO event. Other vacuum related activities for ROMANO, such as outgassing tests of materials, are covered in separate documentation. VPL was asked to provide 270 coated Parylene foils for the ROMANO event. However, due to the developmental nature of some of the procedures, approximately 400 coated foils were processed. In addition, VPL interacted with MFD's Plastics Shop to help supply Parylene substrates to other organizations (i.e., LBL and commercial vendors) which had also been asked to provide coated foils for ROMANO. The purposes of this report are (A) to document the processes developed and the techniques used to produce the foils, and (B) to suggest future directions. The report is divided into four sections describing: (1) nuclear target foil fabrication, (2) Parylene substrate preparation and production, (3) calibration foil fabrication, and (4) foil and substrate inspections

LH2 Target Design & Position Survey Techniques for the MUSE experiment for Precise Proton Radius Measurement

Science.gov (United States)

Le Pottier, Luc; Roy, Pryiashee; Lorenzon, Wolfgang; Raymond, Richard; Steinberg, Noah; Rossi de La Fuente, Erick; MUSE (MUon proton Scattering Experiment) Collaboration

2017-09-01

The proton radius puzzle is a currently unresolved problem which has intrigued the scientific community, dealing with a 7 σ discrepancy between the proton radii determined from muonic hydrogen spectroscopy and electron scattering measurements. The MUon Scattering Experiment (MUSE) aims to resolve this puzzle by performing the first simultaneous elastic scattering measurements of both electrons and muons on the proton, which will allow the comparison of the radii from the two interactions with reduced systematic uncertainties. The data from this experiment is expected to provide the best test of lepton universality to date. The experiment will take place at the Paul Scherrer Institute in Switzerland in 2018. An essential component of the experiment is a liquid hydrogen (LH2) cryotarget system. Our group at the University of Michigan is responsible for the design, fabrication and installation of this system. Here we present our LH2 target cell design and fabrication techniques for successful operation at 20 K and 1 atm, and our computer vision-based target position survey system which will determine the position of the target, installed inside a vacuum chamber, with 0.01 mm or better precision at the height of the liquid hydrogen target and along the beam direction during the experiment.

Metal finishing and vacuum processes groups, Materials Fabrication Division progress report, March-May 1984

International Nuclear Information System (INIS)

Dini, J.W.; Romo, J.G.; Jones, L.M.

1984-01-01

Progress is reported in fabrication and coating activities being conducted for the weapons program, nuclear test program, nuclear design program, magnetic fusion program, and miscellaneous applications

Development of uranium metal targets for 99Mo production

International Nuclear Information System (INIS)

Wiencek, T.C.; Hofman, G.L.

1993-10-01

A substantial amount of high enriched uranium (HEU) is used for the production of medical-grade 99 Mo. Promising methods of producing irradiation targets are being developed and may lead to the reduction or elimination of this HEU use. To substitute low enriched uranium (LEU) for HEU in the production of 99 Mo, the target material may be changed to uranium metal foil. Methods of fabrication are being developed to simplify assembly and disassembly of the targets. Removal of the uranium foil after irradiation without dissolution of the cladding is a primary goal in order to reduce the amount of liquid radioactive waste material produced in the process. Proof-of-concept targets have been fabricated. Destructive testing indicates that acceptable contact between the uranium foil and the cladding can be achieved. Thermal annealing tests, which simulate the cladding/uranium diffusion conditions during irradiation, are underway. Plans are being made to irradiate test targets

Longitudinal gas-density profilometry for plasma-wakefield acceleration targets

Science.gov (United States)

Schaper, Lucas; Goldberg, Lars; Kleinwächter, Tobias; Schwinkendorf, Jan-Patrick; Osterhoff, Jens

2014-03-01

Precise tailoring of plasma-density profiles has been identified as one of the critical points in achieving stable and reproducible conditions in plasma wakefield accelerators. Here, the strict requirements of next generation plasma-wakefield concepts, such as hybrid-accelerators, with densities around 1017 cm-3 pose challenges to target fabrication as well as to their reliable diagnosis. To mitigate these issues we combine target simulation with fabrication and characterization. The resulting density profiles in capillaries with gas jet and multiple in- and outlets are simulated with the fluid code OpenFOAM. Satisfactory simulation results then are followed by fabrication of the desired target shapes with structures down to the 10 μm level. The detection of Raman scattered photons using lenses with large collection solid angle allows to measure the corresponding longitudinal density profiles at different number densities and allows a detection sensitivity down to the low 1017 cm-3 density range at high spatial resolution. This offers the possibility to gain insight into steep density gradients as for example in gas jets and at the plasma-to-vacuum transition.

Copper deposition on fabrics by rf plasma sputtering for medical applications

International Nuclear Information System (INIS)

Segura, G; Guzmán, P; Barrantes, Y; Navarro, G; Asenjo, J; Guadamuz, S; Vargas, VI; Zuñiga, P; Chaves, S; Chaves, J

2015-01-01

The present work is about preparation and characterization of RF sputtered Cu films on cotton by the usage of a Magnetron Sputter Source and 99.995% purity Cu target at room temperature. Cotton fabric samples of 1, 2 and 4 min of sputtering time at discharge pressure of 1×10 −2 Torr and distance between target and sample of 8 cm were used. The main goal was to qualitatively test the antimicrobial action of copper on fabrics. For that purpose, a reference strain of Escherichia Coli ATCC 35218 that were grown in TSA plates was implemented. Results indicated a decrease in the growth of bacteria by contact with Cu; for fabric samples with longer sputtering presented lower development of E. coli colonies. The scope of this research focused on using these new textiles in health field, for example socks can be made with this textile for the treatment of athlete's foot and the use in pajamas, sheets, pillow covers and robes in hospital setting for reducing the spread of microorganisms. (paper)

Study and analysis of how to optimize marketing & sales of a b-to-b company for the target group

OpenAIRE

Kauppila, Kasper

2014-01-01

Study and analysis of how to optimize the marketing & sales strategy of a b-to-b company for the target group. Case study for Green Fortune Plantwall Oy. This thesis is a case study of Green Fortune Plantwall Oy. The objective of this thesis is to study and analyze how to optimize the current marketing and sales strategy of a small b-to-b company for its target group (i.e. architects and interior designers).

Fabrication of a tantalum-clad tungsten target for KENS

International Nuclear Information System (INIS)

Kawai, Masayoshi; Kikuchi, Kenji; Kurishita, Hiroaki; Li, J.-F.; Furusaka, Michihiro

2001-01-01

Since the cold neutron source intensity of KENS (the spallation neutron source at High Energy Accelerator Research Organization) was decreased into about a third of the designed value because a cadmium liner at the cold neutron source deformed and obstructed the neutron beam line, the target-moderator-and-reflector assembly (TMRA) has been replaced by a new one aimed at improving the neutron performance and recovering the cold neutron source. The tantalum target has also been replaced by a tantalum-clad tungsten one. In order to bond the tantalum-clad with the tungsten block, a hot isostatic press (HIP) process was applied and optimized. It was found that gaseous interstitial impurity elements severely attacked tantalum and embrittled, and that the getter materials such as zirconium and tantalum were effective to reduce the embrittlement

GEM-loaded magnetic albumin nanospheres modified with cetuximab for simultaneous targeting, magnetic resonance imaging, and double-targeted thermochemotherapy of pancreatic cancer cells

Directory of Open Access Journals (Sweden)

Wang L

2015-03-01

Full Text Available Ling Wang,1 Yanli An,2 Chenyan Yuan,3 Hao Zhang,2 Chen Liang,2 Fengan Ding,2 Qi Gao,1 Dongsheng Zhang4 1Department of Ultrasonography, Zhong Da Hospital, Medical School, Southeast University, Nanjing, People’s Republic of China; 2Medical School, Southeast University, Nanjing, People’s Republic of China; 3Department of Clinical Laboratory, Zhong Da Hospital, Medical School, Southeast University, Nanjing, People’s Republic of China; 4Jiangsu Key Laboratory for Biomaterials and Devices, Medical School, Southeast University, Nanjing, People’s Republic of China Background: Targeted delivery is a promising strategy to improve the diagnostic imaging and therapeutic effect of cancers. In this paper, novel cetuximab (C225-conjugated, gemcitabine (GEM-containing magnetic albumin nanospheres (C225-GEM/MANs were fabricated and applied as a theranostic nanocarrier to conduct simultaneous targeting, magnetic resonance imaging (MRI, and double-targeted thermochemotherapy against pancreatic cancer cells. Methods: Fe3O4 nanoparticles (NPs and GEM co-loaded albumin nanospheres (GEM/MANs were prepared, and then C225 was further conjugated to synthesize C225-GEM/MANs. Their morphology, mean particle size, GEM encapsulation ratio, specific cell-binding ability, and thermal dynamic profiles were characterized. The effects of discriminating different EGFR-expressing pancreatic cancer cells (AsPC-1 and MIA PaCa-2 and monitoring cellular targeting effects were assessed by targeted MRI. Lastly, the antitumor efficiency of double/C225/magnetic-targeted and nontargeted thermochemotherapy was compared with chemotherapy alone using 3-(4, 5-dimethyl-2-thiazolyl-2,5-diphenyl-2H-tetrazolium bromide (MTT and flow cytometry (FCM assay. Results: When treated with targeted nanospheres, AsPC-1 cells showed a significantly less intense MRI T2 signal than MIA PaCa-2 cells, while both cells had similar signal strength when incubated with nontargeted nanospheres. T2 signal

Analysis of mechanical fabrication experience with CEBAF's production SRF cavities

International Nuclear Information System (INIS)

Mammosser, J.; Kneisel, P.; Benesch, J.

1993-06-01

CEBAF has received a total of 360 five-cell niobium cavities, the largest group of industrially fabricated superconducting cavities so far. An extensive data base exists on the fabrication, surface treatment, assembly and cavity performance parameters. Analysis of the mechanical features of the cavities includes the following: the spread in fabrication tolerances of the cells derived from field profiles of the ''as fabricated'' cavities and the ''as fabricated'' external Q-values of the fundamental power coupler compared to dimensional deviations. A comparison is made of the pressure sensitivity of cavities made of materials from different manufacturers between 760 torr (4.2 K) and 23 torr (2 K)

DESIGN, FABRICATION, AND TESTING OF AN ADVANCED, NON-POLLUTING TURBINE DRIVE GAS GENERATOR

International Nuclear Information System (INIS)

Unknown

2002-01-01

The objectives of this report period were to complete the development of the Gas Generator design, which was done; fabricate and test of the non-polluting unique power turbine drive gas Gas Generator, which has been postponed. Focus during this report period has been to complete the brazing and bonding necessary to fabricate the Gas Generator hardware, continue making preparations for fabricating and testing the Gas Generator, and continuing the fabrication of the Gas Generator hardware and ancillary hardware in preparation for the test program. Fabrication is more than 95% complete and is expected to conclude in early May 2002. the test schedule was affected by relocation of the testing to another test supplier. The target test date for hot fire testing is now not earlier than June 15, 2002

Characterization studies of prototype ISOL targets for the RIA

International Nuclear Information System (INIS)

Greene, John P.; Burtseva, Tatiana; Neubauer, Janelle; Nolen, Jerry A.; Villari, Antonio C.C.; Gomes, Itacil C.

2005-01-01

Targets employing refractory compounds are being developed for the rare isotope accelerator (RIA) facility to produce ion species far from stability. With the 100 kW beams proposed for the production targets, dissipation of heat becomes a challenging issue. In our two-step target design, neutrons are generated in a refractory primary target, inducing fission in the surrounding uranium carbide. The interplay of density, grain size, thermal conductivity and diffusion properties of the UC 2 needs to be well understood before fabrication. Thin samples of uranium carbide were prepared for thermal conductivity measurements using an electron beam to heat the sample and an optical pyrometer to observe the thermal radiation. Release efficiencies and independent thermal analysis on these samples are being undertaken at Oak Ridge National Laboratory (ORNL). An alternate target concept for RIA, the tilted slab approach promises to be simple with fast ion release and capable of withstanding high beam intensities while providing considerable yields via spallation. A proposed small business innovative research (SBIR) project will design a prototype tilted target, exploring the materials needed for fabrication and testing at an irradiation facility to address issues of heat transfer and stresses within the target

Characterization studies of prototype ISOL targets for the RIA

Science.gov (United States)

Greene, John P.; Burtseva, Tatiana; Neubauer, Janelle; Nolen, Jerry A.; Villari, Antonio C. C.; Gomes, Itacil C.

2005-12-01

Targets employing refractory compounds are being developed for the rare isotope accelerator (RIA) facility to produce ion species far from stability. With the 100 kW beams proposed for the production targets, dissipation of heat becomes a challenging issue. In our two-step target design, neutrons are generated in a refractory primary target, inducing fission in the surrounding uranium carbide. The interplay of density, grain size, thermal conductivity and diffusion properties of the UC2 needs to be well understood before fabrication. Thin samples of uranium carbide were prepared for thermal conductivity measurements using an electron beam to heat the sample and an optical pyrometer to observe the thermal radiation. Release efficiencies and independent thermal analysis on these samples are being undertaken at Oak Ridge National Laboratory (ORNL). An alternate target concept for RIA, the tilted slab approach promises to be simple with fast ion release and capable of withstanding high beam intensities while providing considerable yields via spallation. A proposed small business innovative research (SBIR) project will design a prototype tilted target, exploring the materials needed for fabrication and testing at an irradiation facility to address issues of heat transfer and stresses within the target.

Minor Actinide Recycle in Sodium Cooled Fast Reactors Using Heterogeneous Targets

International Nuclear Information System (INIS)

Bays, Samuel; Medvedev, Pavel; Pope, Michael; Ferrer, Rodolfo; Forget, Benoit; Asgari, Mehdi

2009-01-01

This paper investigates the plausible design of transmutation target assemblies for minor actinides (MA) in Sodium Fast Reactors (SFR). A heterogeneous recycling strategy is investigated, whereby after each reactor pass, un-burned MAs from the targets are blended with MAs produced by the driver fuel and additional MAs from Spent Nuclear Fuel (SNF). A design iteration methodology was adopted for customizing the core design, target assembly design and matrix composition design. The overall design was constrained against allowable peak or maximum in-core performances. While respecting these criteria, the overall design was adjusted to reduce the total number of assemblies fabricated per refueling cycle. It was found that an inert metal-hydride MA-Zr-Hx target matrix gave the highest transmutation efficiency, thus allowing for the least number of targets to be fabricated per reactor cycle.

Fabrication of superhydrophobic and antibacterial surface on cotton fabric by doped silica -based sols with nanoparticles of copper

Science.gov (United States)

Berendjchi, Amirhosein; Khajavi, Ramin; Yazdanshenas, Mohammad Esmaeil

2011-11-01

The study discussed the synthesis of silica sol using the sol-gel method, doped with two different amounts of Cu nanoparticles. Cotton fabric samples were impregnated by the prepared sols and then dried and cured. To block hydroxyl groups, some samples were also treated with hexadecyltrimethoxysilane. The average particle size of colloidal silica nanoparticles were measured by the particle size analyzer. The morphology, roughness, and hydrophobic properties of the surface fabricated on cotton samples were analyzed and compared via the scanning electron microscopy, the transmission electron microscopy, the scanning probe microscopy, with static water contact angle (SWC), and water shedding angle measurements. Furthermore, the antibacterial efficiency of samples was quantitatively evaluated using AATCC 100 method. The addition of 0.5% (wt/wt) Cu into silica sol caused the silica nanoparticles to agglomerate in more grape-like clusters on cotton fabrics. Such fabricated surface revealed the highest value of SWC (155° for a 10-μl droplet) due to air trapping capability of its inclined structure. However, the presence of higher amounts of Cu nanoparticles (2% wt/wt) in silica sol resulted in the most slippery smooth surface on cotton fabrics. All fabricated surfaces containing Cu nanoparticles showed the perfect antibacterial activity against both of gram-negative and gram-positive bacteria.

Isolation of bifidobacteria for blood group secretor status targeted personalised nutrition

Directory of Open Access Journals (Sweden)

Harri Mäkivuokko

2012-06-01

Full Text Available Background: Currently, there is a constant need to find microbial products for maintaining or even improving host microbiota balance that could be targeted to a selected consumer group. Blood group secretor status, determining the ABO status, could be used to stratify the consumer group. Objective: We have applied a validated upper intestinal tract model (TIM-1 and culturing methods to screen potential probiotic bacteria from faeces of blood secretor and non-secretor individuals. Design: Faecal samples from healthy volunteers were pooled to age- and sex-matched secretor and non-secretor pools. Faecal pools were run through separate TIM-1 simulations, and bacteria were cultivated from samples taken at different stages of simulations for characterisation. Results: Microbes in secretor pool survived the transit through TIM-1 system better than microbes of non-secretor pool, especially bifidobacteria and anaerobes were highly affected. The differences in numbers of bifidobacteria and lactobacilli isolates after plate cultivations and further the number of distinct RAPD-genotypes was clearly lower in non-secretor pool than in secretor pool. Conclusions: In the present study, we showed that microbiota of secretor and non-secretor individuals tolerate gastrointestinal conditions differently and that a combination of gastrointestinal simulations and cultivation methods proved to be a promising tool for isolating potentially probiotic bacteria.

Reforming Shapes for Material-aware Fabrication

KAUST Repository

Yang, Yongliang; Wang, Jun; Mitra, Niloy J.

2015-01-01

© 2015 The Eurographics Association and John Wiley & Sons Ltd. Published by John Wiley & Sons Ltd. As humans, we regularly associate shape of an object with its built material. In the context of geometric modeling, however, this inter-relation between form and material is rarely explored. In this work, we propose a novel data-driven reforming (i.e.; reshaping) algorithm that adapts an input multi-component model for a target fabrication material. The algorithm adapts both the part geometry and the inter-part topology of the input shape to better align with material-aware fabrication requirements. As output, we produce the reshaped model along with respective part dimensions and inter-part junction specifications. We evaluate our algorithm on a range of man-made models and demonstrate a variety of model reshaping examples focusing only on metal and wooden materials.

Reforming Shapes for Material-aware Fabrication

KAUST Repository

Yang, Yongliang

2015-08-10

© 2015 The Eurographics Association and John Wiley & Sons Ltd. Published by John Wiley & Sons Ltd. As humans, we regularly associate shape of an object with its built material. In the context of geometric modeling, however, this inter-relation between form and material is rarely explored. In this work, we propose a novel data-driven reforming (i.e.; reshaping) algorithm that adapts an input multi-component model for a target fabrication material. The algorithm adapts both the part geometry and the inter-part topology of the input shape to better align with material-aware fabrication requirements. As output, we produce the reshaped model along with respective part dimensions and inter-part junction specifications. We evaluate our algorithm on a range of man-made models and demonstrate a variety of model reshaping examples focusing only on metal and wooden materials.

The effect of interventions on Twitter in four target groups using different measures of influence

NARCIS (Netherlands)

Maanen, P.P. van; Wijn, R.; Boertjes, E.

2014-01-01

In this paper, the influence of interventions on Twitter users is studied. We define influence in (a) number of participants, (b) size of the audience, (c) amount of activity, and (d) reach. Influence is studied for four different target groups: (a) politicians, (b) journalists, (c) employees and

Fabricating an S&OP Process

DEFF Research Database (Denmark)

Lichen, Alex Yu

, constituents of the S&OP process are dispersed in diverse local times and spaces rather than being coordinated in a single time and space by the group demand chain. Accounting is a set of matters of concern. The S&OP process and its purpose of integration come from an “absolute nothingness” – its minimal......Inspired by Latour’s (2005a) notion of matters of concern and M.C. Escher’s Circle Limit III as a representation of the Poincaré Disk, this study follows how an S&OP process was fabricated in a large Swedish manufacturing company. The study claims that when actors are fabricating the S&OP process......, local actors create emergent, ongoing and multiple matters of concern around it. The group demand chain, the actor who is responsible for guiding the implementation of the process, delegates the attempts to close these matters of concern to local actors located in separate times and spaces. As a result...

FPGA fabric specific optimization for RLT design

International Nuclear Information System (INIS)

Perwaiz, A.; Khan, S.A.

2010-01-01

This paper proposes a technique custom to the optimization requirements suited for a particular family of Field Programmable Gate Arrays (FPGAs). As FPGAs have introduced re configurable black boxes there is a need to perform optimization across FPGAs slice fabric in order to achieve optimum performance. Though the Register Transfer Level (RTL) Hardware Descriptive Language (HDL) code should be technology independent but in many design instances it is imperative to understand the target technology especially once the target device embeds dedicated arithmetic blocks. No matter what the degree of optimization of the algorithm is, the configuration of target device plays an important role as far as the device utilization and path delays are concerned Index Terms: Field Programmable Gate Arrays (FPGA), Compression Tree, Bit Width Reduction, Look Ahead Pipelining. (author)

Longitudinal gas-density profilometry for plasma-wakefield acceleration targets

Energy Technology Data Exchange (ETDEWEB)

Schaper, Lucas, E-mail: lschaper01@qub.ac.uk [Universität Hamburg, FB Physik, Institut für Experimentalphysik, Luruper Chaussee 149, 22761 Hamburg (Germany); Deutsches Elektronen-Synchrotron DESY, Notkestraße 85, 22607 Hamburg (Germany); Goldberg, Lars; Kleinwächter, Tobias; Schwinkendorf, Jan-Patrick; Osterhoff, Jens [Deutsches Elektronen-Synchrotron DESY, Notkestraße 85, 22607 Hamburg (Germany)

2014-03-11

Precise tailoring of plasma-density profiles has been identified as one of the critical points in achieving stable and reproducible conditions in plasma wakefield accelerators. Here, the strict requirements of next generation plasma-wakefield concepts, such as hybrid-accelerators, with densities around 10{sup 17} cm{sup −3} pose challenges to target fabrication as well as to their reliable diagnosis. To mitigate these issues we combine target simulation with fabrication and characterization. The resulting density profiles in capillaries with gas jet and multiple in- and outlets are simulated with the fluid code OpenFOAM. Satisfactory simulation results then are followed by fabrication of the desired target shapes with structures down to the 10 µm level. The detection of Raman scattered photons using lenses with large collection solid angle allows to measure the corresponding longitudinal density profiles at different number densities and allows a detection sensitivity down to the low 10{sup 17} cm{sup −3} density range at high spatial resolution. This offers the possibility to gain insight into steep density gradients as for example in gas jets and at the plasma-to-vacuum transition.

Solvent-resistant small molecule solar cells by roll-to-roll fabrication via introduction of azide cross-linkable group

DEFF Research Database (Denmark)

Chen, Mei-Rong; Fan, Cong-Cheng; Andersen, Thomas Rieks

2014-01-01

A novel cross-linkable azide-functionalized diketopyrrolopyrrole based compound DPP(BT-N-3)(2) was designed and synthesized via Stille coupling. Cross-linking of such molecule could help us fabricate insoluble film which could be used to fabricate heterostructures through solution processing......, without dissolving the pre-patterned layers. In order to investigate the photovoltaic performances of the newly synthesized compound, large area solar cells were produced by roll coating technique. Two set of devices were fabricated by employing DPP(BT-N-3)(2) as either an electron donor or acceptor....... A best power conversion efficiency of 0.067%, combined with an open circuit voltage of 0.53 V, and a fill factor of 37.6% were obtained for the device with DPP(BT-N-3)(2) as an electron acceptor. In addition, we could prove that the large area small molecule based organic solar cells could be fabricated...

The Ignition Target for the National Ignition Facility

International Nuclear Information System (INIS)

Atherton, L J; Moses, E I; Carlisle, K; Kilkenny, J

2007-01-01

The National Ignition Facility (NIF) is a 192 beam Nd-glass laser facility presently under construction at Lawrence Livermore National Laboratory (LLNL) for performing inertial confinement fusion (ICF) and experiments studying high energy density (HED) science. When completed in 2009, NIF will be able to produce 1.8 MJ, 500 TW of ultraviolet light for target experiments that will create conditions of extreme temperatures (>10 8 K), pressures (10-GBar) and matter densities (> 100 g/cm 3 ). A detailed program called the National Ignition Campaign (NIC) has been developed to enable ignition experiments in 2010, with the goal of producing fusion ignition and burn of a deuterium-tritium (DT) fuel mixture in millimeter-scale target capsules. The first of the target experiments leading up to these ignition shots will begin in 2008. Targets for the National Ignition Campaign are both complex and precise, and are extraordinarily demanding in materials fabrication, machining, assembly, cryogenics and characterization. An overview of the campaign for ignition will be presented, along with technologies for target fabrication, assembly and metrology and advances in growth and x-ray imaging of DT ice layers. The sum of these efforts represents a quantum leap in target precision, characterization, manufacturing rate and flexibility over current state-of-the-art

COATING AND MANDREL EFFECTS ON FABRICATION OF GLOW DISCHARGE POLYMER NIF SCALE INDIRECT DRIVE CAPSULES

International Nuclear Information System (INIS)

NIKROO, A.; PONTELANDOLFO, J.M.; CASTILLO, E.R.

2002-01-01

OAK A271 COATING AND MANDREL EFFECTS ON FABRICATION OF GLOW DISCHARGE POLYMER NIF SCALE INDIRECT DRIVE CAPSULES. Targets for the National Ignition Facility (NIF) need to be about 200 (micro)m thick and 2 mm in diameter. These dimensions are well beyond those currently fabricated on a routine basis. They have investigated fabrication of near NIF scale targets using the depolymerizable mandrel technique. Poly-alpha-methylstyrene (PAMS) mandrels, about 2 mm in diameter, of varying qualities were coated with as much as 125 (micro)m of glow discharge polymer (GDP). The surface finish of the final shells was examined using a variety of techniques. A clear dependence of the modal spectrum of final GDP shell on the quality of the initial PAMS mandrels was observed. isolated features were found to be the greatest cause for a shell not meeting the NIF standard

Accuracy of CAD-CAM-fabricated removable partial dentures.

Science.gov (United States)

Arnold, Christin; Hey, Jeremias; Schweyen, Ramona; Setz, Jürgen M

2018-04-01

The conventional fabrication of removable partial dentures (RPDs) is a complex, error-prone, time-consuming, and expensive process. The use of computer-aided design and computer-aided manufacturing (CAD-CAM) techniques, especially rapid prototyping, promises a more effective method for fabricating RPD frameworks. The purpose of this in vitro study was to evaluate the fit of RPD clasps fabricated by means of 4 different CAD-CAM-systems and to compare those fittings with that of the conventional lost-wax casting technique (LWT). A master model of a partially edentulous maxilla with the canines and second molars as the remaining teeth was fabricated. After the model was optically scanned, we designed a quadrangularly supported RPD with 4 clasps and a palatal strap major connector. A standard tessellation language data set was used to fabricate 12 identical RPDs by using 4 different CAD-CAM techniques: indirect rapid prototyping (wax inject printing combined with LWT), direct rapid prototyping (selective laser melting), indirect milling (wax milling with LWT), and direct milling (resin milling [polyetheretherketone]). Three conventionally cast RPDs (LWT) served as the control group. The fit accuracy of the clasps (n=12 for each group) was determined in both the horizontal and vertical dimensions by using light microscopy. Indirectly milled RPDs (117 ±34 μm horizontal and 45 ±21 μm vertical) and directly milled RPDs (43 ±23 μm horizontal, and 38 ±21 μm vertical) showed significantly better (P<.05) fit than did conventionally fabricated LWT RPDs (133 ±59 μm horizontal; 73 ±25 μm vertical). The worst fit was found for RPDs fabricated using indirect rapid prototyping (323 ±188 μm horizontal and 112 ±60 μm vertical) or direct rapid prototyping (365 ±205 μm horizontal and 363 ±133 μm vertical), which were unstable on the master model, making them unsuitable for clinical use. Most RPDs exhibited smaller vertical measuring distances. Compared with the LWT

Group II intron inhibits conjugative relaxase expression in bacteria by mRNA targeting

Science.gov (United States)

Piazza, Carol Lyn; Smith, Dorie

2018-01-01

Group II introns are mobile ribozymes that are rare in bacterial genomes, often cohabiting with various mobile elements, and seldom interrupting housekeeping genes. What accounts for this distribution has not been well understood. Here, we demonstrate that Ll.LtrB, the group II intron residing in a relaxase gene on a conjugative plasmid from Lactococcus lactis, inhibits its host gene expression and restrains the naturally cohabiting mobile element from conjugative horizontal transfer. We show that reduction in gene expression is mainly at the mRNA level, and results from the interaction between exon-binding sequences (EBSs) in the intron and intron-binding sequences (IBSs) in the mRNA. The spliced intron targets the relaxase mRNA and reopens ligated exons, causing major mRNA loss. Taken together, this study provides an explanation for the distribution and paucity of group II introns in bacteria, and suggests a potential force for those introns to evolve into spliceosomal introns. PMID:29905149

New fabrication techniques for the nuclear fuels of tomorrow

International Nuclear Information System (INIS)

Babelot, J.F.; Bokelund, H.; Gerontopoulos, P.; Gueugnon, J.F.; Richter, K.

1995-01-01

The shift of the emphasis of the work at the Institute for Transuranium Elements (ITU) from the development of fuels based on uranium and plutonium to safety aspects concerning the use of plutonium and other of actinides, necessitates the production of targets containing appreciable amounts of minor actinides for irradiation experiments. The handling of minor actinides requires additional protective measures, combined with improved fuel fabrication techniques. The boundary conditions for a suitable process are flexibility, adaptability to remote control, and minimization of dust formation. A method based on the sol-gel fabrication technique meets these criteria, and was selected for the present developments at ITU. (author)

Polymorphous computing fabric

Science.gov (United States)

Wolinski, Christophe Czeslaw [Los Alamos, NM; Gokhale, Maya B [Los Alamos, NM; McCabe, Kevin Peter [Los Alamos, NM

2011-01-18

Fabric-based computing systems and methods are disclosed. A fabric-based computing system can include a polymorphous computing fabric that can be customized on a per application basis and a host processor in communication with said polymorphous computing fabric. The polymorphous computing fabric includes a cellular architecture that can be highly parameterized to enable a customized synthesis of fabric instances for a variety of enhanced application performances thereof. A global memory concept can also be included that provides the host processor random access to all variables and instructions associated with the polymorphous computing fabric.

Enhanced washing durability of hydrophobic coating on cellulose fabric using polycarboxylic acids

International Nuclear Information System (INIS)

Huang Wenqi; Xing Yanjun; Yu Yunyi; Shang Songmin; Dai Jinjin

2011-01-01

Nine polycarboxylic acids were used to improve washing durability of hydrophobic cellulose fabric finished by sol-gel method. By simultaneous forming ester-bridge between cellulose and silica layer by ester bond, polycarboxylic acids could anchor silica coating onto cellulose fabric to strengthen the adhesion of organic-inorganic hybrid coating. The wettability of treated fabrics was characterized by water contact angle, spray test and hydrostatic pressure test. The results showed that all investigated polycarboxylic acids could improve the durability. The polycarboxylic acid with proper distance between terminal carboxylic acid groups and number of carboxylic acid groups showed the highest durability. 1,2,3,4-butanetetracarboxylic acid (BTCA) led to the best durability of hydrophobic cellulose fabric with water contact angle of 137.6 o (recovery percentage of 94.2%) after 30 washing times. The effect of BTCA on durability was characterized by scanning electron microscopy. This study demonstrated that the surface treatment using polycarboxylic acids and mixed organosilanes is a promising alternative for achieving durable hydrophobic fabrics.

Preparation of thin nuclear targets

International Nuclear Information System (INIS)

Muggleton, A.H.F.

1979-03-01

Thin film backings, sources and targets are needed for many applications in low energy nuclear physics and nuclear chemistry experiments. A survey of techniques used in the preparation of nuclear targets is first briefly discussed. These are classified as chemical, mechanical and physical preparations. Vacuum evaporation, being the most generally used technique, is discussed in detail. It is highly desirable to monitor the film thickness and control the deposition rate during evaporation and to measure the final target thickness after deposition has concluded. The relative merits of various thickness measuring techniques are described. Stages in the fabrication and mounting of self-supporting foils are described in detail, with emphasis given to the preparation of thin self-supporting carbon foils used as target backings and stripper foils. Various target backings, and the merits of the more generally used release agents are described in detail. The preparations of more difficult elemental targets are discussed, and a comprehensive list of the common targets is presented

Microencapsulation and fabrication of fuel pellets for inertial confinement fusion

International Nuclear Information System (INIS)

Nolen, R.L. Jr.; Kool, L.B.

1981-01-01

Various microencapsulation techniques were evaluated for fabrication of thermonuclear fuel pellets for use in existing experimental facilities studying inertial confinement fusion and in future fusion-power reactors. Coacervation, spray drying, in situ polymerization, and physical microencapsulation methods were employed. Highly spherical, hollow polymeric shells were fabricated ranging in size from 20 to 7000 micron. In situ polymerization microencapsulation with poly(methyl methacrylate) provided large shells, but problems with local wall defects still must be solved. Extension to other polymeric systems met with limited success. Requirements for inertial confinement fusion targets are described, as are the methods that were used

Fabrication of green polymeric membranes

KAUST Repository

Kim, Dooli; Nunes, Suzana Pereira

2017-01-01

Provided herein are methods of fabricating membranes using polymers with functionalized groups such as sulfone (e.g., PSf and PES), ether (e.g., PES), acrylonitrile (e.g., PAN), fluoride(e.g., pvdf and other fluoropolymers), and imide (e.g., extem) and ionic liquids. Also provided are membranes made by the provided methods.

Fabrication of green polymeric membranes

KAUST Repository

Kim, Dooli

2017-06-16

Provided herein are methods of fabricating membranes using polymers with functionalized groups such as sulfone (e.g., PSf and PES), ether (e.g., PES), acrylonitrile (e.g., PAN), fluoride(e.g., pvdf and other fluoropolymers), and imide (e.g., extem) and ionic liquids. Also provided are membranes made by the provided methods.

Design & fabrication of cantilever array biosensors

DEFF Research Database (Denmark)

Boisen, Anja; Thundat, T

2009-01-01

Surface immobilization of functional receptors on microfabricated cantilever arrays offers a new paradigm for the development of biosensors based on nanomechanics. Microcantilever-based systems are capable of real-time, multiplexed detection of unlabeled disease markers in extremely small volumes......, electronic processing, and even local telemetry on a single chip have the potential of satisfying the need for highly sensitive and selective multiple-target detection in very small samples. Here we will review the design and fabrication process of cantilever-based biosensors....

Targets with thin ferromagnetic layers for transient field experiments

International Nuclear Information System (INIS)

Gallant, J.L.; Dmytrenko, P.

1982-01-01

Multilayer targets containing a central layer sufficiently thin so that all recoil nuclei can traverse it and subsequently stop in a suitable cubic environment have been prepared. Such targets are required in experiments making use of a magnetic field acting on an ion moving through a ferromagnetic material. The preparation and annealing of the ferromagnetic foils (iron and gadolinium) and the fabrication of the multilayer targets are described. (orig.)

Dukungan Target Group Terhadap Zoning Regulation

Directory of Open Access Journals (Sweden)

Susi Ridhawati

2014-05-01

Full Text Available Kegiatan pembangunan yang diwarnai oleh market driven akan menyebabkan kerusakan lingkungan. Apabila terjadi secara terus-menerus, bisa mengakibatkan penurunan kualitas lingkungan hidup. Oleh karena itu penataan ruang (spatial planning menjadi aspek yang amat penting agar ruang yang terbatas dapat digunakan secara efisien dengan tetap memelihara kelestarian dan daya dukung lingkungan hidup. Proses invasi dan urban sprawl sebagai akibat dari keterbatasan ruang perkotaan telah merembet ke sebagian daerah di Kabupaten Sleman, terutama di wilayah Kecamatan Mlati. Perkembangan wilayah di daerah ini perlu mendapatkan perhatian khusus agar di kemudian hari tidak menjadi unmanaged growth. Untuk menjaga kelestarian alam dan mengurangi dampak kerusakan lingkungan yang bisa berakibat terhadap terganggunya sistem ekologi wilayah sekitar Kabupaten Sleman, Badan Pengendalian Pertanahan Daerah (BPPD Kabupaten Sleman melakukan pengendalian atas perubahan penggunaan tanah melalui sosialisasi atas kebijakan pertanahan yang telah ditetapkan Pemerintah Kabupaten Sleman. BPPD memasang/membuat papan informasi/baliho pada tempat strategis, sehingga dapat dibaca dengan mudah oleh masyarakat. Salah satu baliho dipasang di kawasan pertanian di Jalan Sendari-Gombang, Tirtoadi, Kecamatan Mlati. Berkenaan dengan hal di atas, penelitian ini bertujuan untuk menilai sikap target grup terhadap zoning regulations dengan studi kasus di Jalan Sendari Gombang Tirtoadi, Kecamatan Mlati. Penelitian juga ingin mengungkap faktor-faktor yang memengaruhi dukungan target grup terhadap implementasi zoning regulations di Kecamatan Mlati, terutama di Jalan Sendari-Gombang, Tirtoadi. Penelitian menggunakan pendekatan deskriptif naturalistik dengan metode studi kasus.

Surface modification of cotton fabrics by gas plasmas for color strength and adhesion by inkjet ink printing

International Nuclear Information System (INIS)

Pransilp, Porntapin; Pruettiphap, Meshaya; Bhanthumnavin, Worawan; Paosawatyanyong, Boonchoat; Kiatkamjornwong, Suda

2016-01-01

Graphical abstract: - Highlights: • Both O_2 and N_2 plasma increased cotton surface wettability and higher K/S. • SF6 plasma gave hydrophobicity on cotton surface and increased contact angle to 138°. • Plasma treatment on cotton fabric produced surface roughness. • XPS confirmed the generation of new functional groups on cotton fabric. • Wettability and surface roughness controlled K/S and good ink adhesion. - Abstract: Surface properties of cotton fabric were modified by three types of gas plasma pretreatment, namely, oxygen (O_2), nitrogen (N_2) and sulfur hexafluoride (SF_6), to improve ink absorption of water-based pigmented inkjet inks and color reproduction of the treated surfaces. Effects of gas plasma exposure parameters of power, exposure time and gas pressure on surface physical and chemical properties of the treated fabrics were investigated. XPS (X-ray photoelectron spectroscopy) was used to identify changes in functional groups on the fabric surface while AFM (atomic force microscopy) and SEM (scanning electron microscopy) were used to reveal surface topography of the fabric. Color spectroscopic technique was used to investigate changes in color strength caused by different absorptions of the printed fabrics. The O_2 plasma treatments produced new functional groups, −O−C−O/C=O and O−C=O while N_2 plasma treatments produced additionally new functional groups, C−N and O=C−NH, onto the fabric surface which increased hydrophilic properties and surface energy of the fabric. For cotton fabric treated with SF_6 plasma, the fluorine functionalization was additionally found on the surface. Color strength values (K/S) increased when compared with those of the untreated fabrics. SF_6 plasma-treated fabrics were hydrophobic and caused less ink absorption. Fabric surface roughness caused by plasma etching increased fabric surface areas, captured more ink, and enhanced a larger ink color gamut and ink adhesion. Cotton fabrics exhibited higher

Summary abstract: microspot target development with seeded and patterned plasma polymers

International Nuclear Information System (INIS)

Letts, S.A.; Miller, D.E.; Corley, R.A.; Tillotson, T.M.; Witt, L.A.

1985-01-01

In inertial confinement fusion (ICF) energy is transferred from the laser to the target through the interaction of extremely high intensity laser light with the target plasma. To better understand laser-plasma interactions, a new class of targets was designed to study long scale-length plasmas (many hundred times the laser wavelength) by measurement of the temperature and density of the plasma as a function of time. The specifications for the target called for a freestanding hydrocarbon polymer (CH) film with a sharply defined spot (microspot) in the center seeded with either silicon or sulfur. The target film was fabricated using a three-step procedure which consisted of deposition of the hydrocarbon film, definition of the microspot, and then deposition of a seeded spot through a mask. In the final assembly step, the film containing the microspot was mounted over a 1.5 mm diam hole in a support. The support was either a plastic ring or a copper foil electroplated with 3 μm of gold. The fabrication of this type of target is described

Conductive cooling of high-power RIB targets

International Nuclear Information System (INIS)

Talbert, W.L.; Drake, D.M.; Wilson, M.T.; Lenz, J.W.; Hsu, H.-H.

2002-01-01

A short review is presented of target cooling approaches suggested for targets irradiated by intense high-energy proton beams to produce radioactive species for use in a broad range of physics studies. This work reports on conductive cooling approaches for operation at temperatures lower than effective for radiative cooling. The possibilities for conductive cooling are discussed, and a prototype test target is described. This target was constructed for an experiment, designed to validate the numerical analysis approaches, at the TRIUMF/ISAC facility. Fabrication issues and the results of the experiment are presented, followed by a discussion of the implications of the experiment outcome for future development of targets to produce intense beams of radioactive ions

Gel Fabrication of Molybdenum “Beads”

Energy Technology Data Exchange (ETDEWEB)

Lowden, Richard Andrew [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Armstrong, Beth L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Cooley, Kevin M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division

2016-11-01

Spherical molybdenum particles or “beads” of various diameters are of interest as feedstock materials for the additive manufacture of targets and assemblies used in the production of ⁹⁹Mo medical isotopes using accelerator technology. Small metallic beads or ball bearings are typically fabricated from wire; however, small molybdenum spheres cannot readily be produced in this manner. Sol-gel processes are often employed to produce small dense microspheres of metal oxides across a broad diameter range that in the case of molybdenum could be reduced and sintered to produce metallic spheres. These Sol-gel type processes were examined for forming molybdenum oxide beads; however, the molybdenum trioxide was chemically incompatible with commonly used gelation materials. As an alternative, an aqueous alginate process being assessed for the fabrication of oxide spheres for catalyst applications was employed to form molybdenum trioxide beads that were successfully reduced and sintered to produce small molybdenum spheres.

Fabrication technology and characteristics of AmO2-MgO cercer materials for transmutation

International Nuclear Information System (INIS)

Croixmarie, Y.; Mocellin, A.; Warin, D.

2000-01-01

This paper deals with the fabrication technology and the physico-chemical properties of target materials prepared for the ECRIX experiment in the French PHENIX reactor. The ECRIX target materials consist of pellets made of a ceramic-ceramic type composite in which particles of americium oxide are microdispersed in an inert matrix of magnesium oxide

Preparation of targets using electron gun systems

International Nuclear Information System (INIS)

Maier-Komor, P.

1975-01-01

Most targets of isotopes with very low vapor pressure can only be fabricated by vacuum deposition using an electron gun system or a heavy ion sputtering system. Heavy ion sputtering is a very new technique with many unsolved problems. Therefore it seems to be easier to work with an electron gun. Different commercially available electron guns, which are all designed for the high evaporation rates used in industry, are examined for their qualification in processing small amounts of material as used in fabrication of isotope targets. Electron backscattering and the associated efficiency of the electron beam power is strongly dependent on the atomic number Z of the evaporant and the incident angle of the electron beam on the surface of the evaporant. This dependence leads also to the undesired effects to the target layers from electrons and ions. Some precautions are necessary against the effects of the electrons and ions, which are formed in the plasma directly over the beam impact point. Beam power and beam density have to be chosen to get a constant evaporation rate and a low enough condensation rate in order not to overheat the target substrates. To evaporate some metals it may be helpful to pulse the electron beam

Developing Fabrication Technologies to Provide On Demand Manufacturing for Exploration of the Moon and Mars

Science.gov (United States)

Hammond, Monica S.; Good, James E.; Gilley, Scott D.; Howard, Richard W.

2006-01-01

NASA's human exploration initiative poses great opportunity and risk for manned and robotic missions to the Moon, Mars, and beyond. Engineers and scientists at the Marshall Space Flight Center (MSFC) are developing technologies for in situ fabrication capabilities during lunar and Martian surface operations utilizing provisioned and locally refined materials. Current fabrication technologies must be advanced to support the special demands and applications of the space exploration initiative such as power, weight and volume constraints. In Situ Fabrication and Repair (ISFR) will advance state-of-the-art technologies in support of habitat structure development, tools, and mechanical part fabrication. The repair and replacement of space mission components, such as life support items or crew exercise equipment, fall within the ISFR scope. This paper will address current fabrication technologies relative to meeting ISFR targeted capabilities, near-term advancement goals, and systematic evaluation of various fabrication methods.

Overview on the target fabrication facilities at ELI-NP and ongoing strategies

Science.gov (United States)

Gheorghiu, C. C.; Leca, V.; Popa, D.; Cernaianu, M. O.; Stutman, D.

2016-10-01

Along with the development of petawatt class laser systems, the interaction between high power lasers and matter flourished an extensive research, with high-interest applications like: laser nuclear physics, proton radiography or cancer therapy. The new ELI-NP (Extreme Light Infrastructure - Nuclear Physics) petawatt laser facility, with 10PW and ~ 1023W/cm2 beam intensity, is one of the innovative projects that will provide novel research of fundamental processes during light-matter interaction. As part of the ELI-NP facility, Targets Laboratory will provide the means for in-house manufacturing and characterization of the required targets (mainly solid ones) for the experiments, in addition to the research activity carried out in order to develop novel target designs with improved performances. A description of the Targets Laboratory with the main pieces of equipment and their specifications are presented. Moreover, in view of the latest progress in the target design, one of the proposed strategies for the forthcoming experiments at ELI-NP is also described, namely: ultra-thin patterned foil of diamond-like carbon (DLC) coated with a carbon-based ultra-low density layer. The carbon foam which behaves as a near-critical density plasma, will allow the controlled-shaping of the laser pulse before the main interaction with the solid foil. Particular emphasis will be directed towards the target's design optimization, by simulation tests and tuning the key-properties (thickness/length, spacing, density foam, depth, periodicity etc.) which are expected to have a crucial effect on the laser-matter interaction process.

Light-ion spectroscopy with exotic targets

International Nuclear Information System (INIS)

Struble, G.L.; Lanier, R.G.

1992-01-01

Understanding the rich and diverse aspects underlying the physics of nuclear structure requires a variety of experimental techniques. In our laboratory, we have concentrated on experimental techniques using light-ion probes and isotopes that are technically difficult to fabricate into targets. In particular, our studies of p-, d-, and t-induced nuclear reactions on the radioactive targets of 152,154 Eu and 148 Gd have illuminated some very specific and very interesting features of nuclear structure near the N = 89 shape-transition region

Electroforming copper targets for RTNS-II

International Nuclear Information System (INIS)

Kelley, W.K.; Dini, J.W.; Logan, C.M.

1981-01-01

Copper targets used in RTNS II, which is the world's most intense 14-MeV neutron source, contain water cooling channels for temperature control. There are two methods for fabricating these targets: (1) diffusion bonding a copper panel containing photoetched channels to another copper panel, and (2) an electroforming technique which involves filling the photoetched channels with wax, plating thick copper to seal over the channels and then removing the wax. Development of this latter process and results obtained with it are described

Fabrication of 94Zr thin target for RDM lifetime measurement

International Nuclear Information System (INIS)

Gupta, Chandan Kumar; Rohilla, Aman; Chamoli, S.K.; Abhilash, S.R.; Kabiraj, D.; Singh, R.P.; Mehta, D.

2013-01-01

The aim of the activity was to make a thin target of isotopically enriched 94 Zr for lifetime measurement experiment to be done with the plunger setup at the Inter University Accelerator Center (IUAC) Delhi

Fabrication and characterization of UV-emitting nanoparticles as novel radiation sensitizers targeting hypoxic tumor cells

Science.gov (United States)

Squillante, Michael R.; Jüstel, Thomas; Anderson, R. Rox; Brecher, Charles; Chartier, Daniel; Christian, James F.; Cicchetti, Nicholas; Espinoza, Sara; McAdams, Daniel R.; Müller, Matthias; Tornifoglio, Brooke; Wang, Yimin; Purschke, Martin

2018-06-01

Radiation therapy is one of the primary therapeutic techniques for treating cancer, administered to nearly two-thirds of all cancer patients. Although largely effective in killing cancer cells, radiation therapy, like other forms of cancer treatment, has difficulty dealing with hypoxic regions within solid tumors. The incomplete killing of cancer cells can lead to recurrence and relapse. The research presented here is investigating the enhancement of the efficacy of radiation therapy by using scintillating nanoparticles that emit UV photons. UV photons, with wavelengths between 230 nm and 280 nm, are able to inactivate cells due to their direct interaction with DNA, causing a variety of forms of damage. UV-emitting nanoparticles will enhance the treatment in two ways: first by generating UV photons in the immediate vicinity of cancer cells, leading to direct and oxygen-independent DNA damage, and second by down-converting the applied higher energy X-rays into softer X-rays and particles that are more efficiently absorbed in the targeted tumor region. The end result will be nanoparticles with a higher efficacy in the treatment of hypoxic cells in the tumor, filling an important, unmet clinical need. Our preliminary experiments show an increase in cell death using scintillating LuPO4:Pr nanoparticles over that achieved by the primary radiation alone. This work describes the fabrication of the nanoparticles, their physical characterization, and the spectroscopic characterization of the UV emission. The work also presents in vitro results that demonstrate an enhanced efficacy of cell killing with x-rays and a low unspecific toxicity of the nanoparticles.

Fabrication of Spin-Transfer Nano-Oscillator by Colloidal Lithography

Directory of Open Access Journals (Sweden)

Bin Fang

2015-01-01

Full Text Available We fabricate nanoscale spin-transfer oscillators (STOs by utilizing colloidal nanoparticles as a lithographic mask. By this approach, high quality STO devices can be fabricated, and as an example the fabricated STO devices using MgO magnetic tunnel junction as the basic cell exhibit current-induced microwave emission with a large frequency tunability of 0.22 GHz/mA. Compared to the conventional approaches that involve a step of defining nanoscale elements by means of electron beam lithography, which is not readily available for many groups, our strategy for STO fabrication does not require the sophisticated equipment (~ million dollars per unit and expensive lithography resist, while being cost-effective and easy to use in laboratory level. This will accelerate efforts to implement STO into on-chip integrated high-radio frequency applications.

Utilization of process TEG for fabrication of HTS circuits

International Nuclear Information System (INIS)

Hato, T.; Okada, Y.; Maruyama, M.; Suzuki, H.; Wakana, H.; Adachi, S.; Kawabe, U.; Tanabe, K.

2006-01-01

We improved the fabrication process of high-temperature superconducting (HTS) sampler circuits with multilayer structures by utilizing a test elements group (TEG). Among a lot of difficulties in the HTS circuit fabrication process, loss of oxygen is one of the most significant problems. Since the film transition temperature (T c ) has a strong relationship with the resistance at room temperature, we fabricated a test pattern on the same wafer of the circuits and measured the resistance at room temperature by using a prober to estimate the T c of each layer. By introducing the measurement of the normal resistance after each process, we found better process conditions without a T c drop. Moreover, we constructed a low-temperature probing system, in which we can measure the junction TEG. The system enabled feedback of the fabrication condition soon after the junction process. The utilization of the process TEG contributed to reproducible fabrication of HTS circuits and that is a promising advance of the HTS circuit technology

Evaluation of the fit of zirconia copings fabricated by direct and indirect digital impression procedures.

Science.gov (United States)

Lee, Bora; Oh, Kyung Chul; Haam, Daewon; Lee, Joon-Hee; Moon, Hong-Seok

2018-02-07

Intraoral scanners are effective for direct digital impression when dental restorations are fabricated using computer-aided design and computer-aided manufacturing (CAD-CAM); however, if the abutment tooth cannot be dried completely or the prepared margin is placed subgingivally, accurate digital images cannot always be guaranteed. The purpose of this in vitro study was to compare the internal and marginal discrepancies of zirconia copings fabricated directly using an intraoral scanner with those fabricated indirectly with impression scanning. Forty-five resin dies fabricated with a 3-dimensional (3D) printer were divided into 3 groups: direct scanning (DS), impression scanning (IMP), and lost-wax casting (LW). For the DS group, a resin die was scanned with an intraoral scanner (Trios; 3Shape), whereas for the IMP group, impressions made with polyether were scanned with a cast scanner (D700; 3Shape). The zirconia copings were fabricated in the same way in the DS and IMP groups. For the LW group, impressions were made in the same way as in the IMP group, and Ni-Cr alloy copings were fabricated using LW. The marginal and internal discrepancies of the copings were measured by cementing them onto resin dies, embedding them in acrylic resin, and sectioning them in a buccolingual direction. The cement layer was measured, and the Kruskal-Wallis test was used to detect significant differences (α=.05). A nonparametric Friedman test was also performed to compare the measurements of each group by location (α=.05). The mean marginal discrepancies in the DS, IMP, and LW groups were 18.1 ±9.8, 23.2 ±17.2, and 32.3 ±18.6 μm (mean ±standard deviation), respectively. The mean internal discrepancies of the DS, IMP, and LW groups in the axial area were 38.0 ±9.1, 47.0 ±16.3, and 36.5 ±15.8 μm, and those in the occlusal area were 36.7 ±16.9, 33.4 ±21.6, and 44.5 ±31.9 μm, respectively. No statistically significant differences were found in marginal or internal

Fabrication drawings of fuel pins for FUJI project among PSI, JNC and NRG. Revised version

International Nuclear Information System (INIS)

Ozawa, Takayuki; Nakazawa, Hiroaki; Abe, Tomoyuki; Nagayama, Masahiro

2002-02-01

Irradiation tests and post-irradiation examinations in the framework of JNC-PSI-NRG collaboration project will be performed in 2003-2005. Irradiation fuel pins will be fabricated by the middle of 2003. The fabrication procedure for irradiation fuel pins has been started in 2001. Several fabrication tests and qualification tests in JNC and PSI (Paul Scherrer Institute, Switzerland) have been performed before the fuel pin fabrication. According to the design assignment between PSI and JNC in the frame of this project, PSI should make a specification document for the fuel pellet, the sphere-pac fuel particles, the vipac fuel particles, and the fuel pin. JNC should make a fabrication drawing for irradiation pins. JNC has been performed the fuel design in cooperation with PSI and NRG (Nuclear Research and Consultancy Group, Netherlands). In this project, the pelletized fuel, the sphere-pac fuel, and the vipac fuel will be simultaneously irradiated on HFR (High Flux Reactor, Netherlands). This fabrication drawing has been made under the design assignment with PSI, and consists of the drawing of MOX pellet, thermal insulator pellet, pin components, fuel segments, and the constructed pin. The fabrication drawings were approved in October 2001, but after that, the optimization of specifications has been discussed and agreed among all partners. In this report, the revised fabrication drawings will be shown. Based on the commission of Plutonium Fuel Technology Group, Advanced Fuel Recycle Technology Division, this design work has been performed in Fuel Design and Evaluation Group, Plutonium Fuel Fabrication Division, Plutonium Fuel Center. (author)

An inexpensive and fast method for infiltration coating of complex geometry matrices for ISOL production target applications

International Nuclear Information System (INIS)

Kawai, Y.; Alton, G.D.; Bilheux, J.-C.

2005-01-01

An inexpensive, fast, and close to universal infiltration coating technique has been developed for fabricating fast diffusion-release ISOL targets. Targets are fabricated by deposition of finely divided (∼1μm) compound materials in a paint-slurry onto highly permeable, complex structure reticulated-vitreous-carbon-foam (RVCF) matrices, followed by thermal heat treatment. In this article, we describe the coating method and present information on the physical integrity, uniformity of deposition, and matrix adherence of SiC, HfC and UC 2 targets, destined for on-line use as targets at the Holifield Radioactive Ion Beam Facility (HRIBF)

INFLUENCE OF FABRIC TIGHTNESS ON SPIRALITY OF WEFTKNITTED PLAIN COTTON FABRIC

Directory of Open Access Journals (Sweden)

A.K.M. Mobarok Hossain

2011-01-01

Full Text Available Global demand for knitted garments is growing at a faster rate than that of woven items.Currently around 50% of clothing needs in the developed countries is met by knit goods. So ensuring the required quality in a knitted fabric is a vital issue for the manufacturer. One of the major problems encountered in knitted fabric is spirality. It affects particularly single jersey fabric and presents a serious problem during garment confection and use. So controlling spirality is a basic requirement for producing quality knitted fabric. Though there are several factors that contribute to knitted fabric spirality, yarn twist and relative tightness of the fabric are said tobe the most significant ones. In this work the basic single jersey fabric, i.e. plain jersey cotton fabrics were produced by a Hosiery knitting machine and spirality values were observed for different yarn T.P.I. and tightness factor at relaxed state. It was found that tightness factor has a direct influence on knitted fabric spirality with a high degree of correlation. The work thus gives an idea to deal this problem by controlling the knitting parameters.

Fabrication of small-orifice fuel injectors for diesel engines.

Energy Technology Data Exchange (ETDEWEB)

Woodford, J. B.; Fenske, G. R.

2005-04-08

Diesel fuel injector nozzles with spray hole diameters of 50-75 {micro}m have been fabricated via electroless nickel plating of conventionally made nozzles. Thick layers of nickel are deposited onto the orifice interior surfaces, reducing the diameter from {approx}200 {micro}m to the target diameter. The nickel plate is hard, smooth, and adherent, and covers the orifice interior surfaces uniformly.

Control of the interaction strength of photonic molecules by nanometer precise 3D fabrication.

Science.gov (United States)

Rawlings, Colin D; Zientek, Michal; Spieser, Martin; Urbonas, Darius; Stöferle, Thilo; Mahrt, Rainer F; Lisunova, Yuliya; Brugger, Juergen; Duerig, Urs; Knoll, Armin W

2017-11-28

Applications for high resolution 3D profiles, so-called grayscale lithography, exist in diverse fields such as optics, nanofluidics and tribology. All of them require the fabrication of patterns with reliable absolute patterning depth independent of the substrate location and target materials. Here we present a complete patterning and pattern-transfer solution based on thermal scanning probe lithography (t-SPL) and dry etching. We demonstrate the fabrication of 3D profiles in silicon and silicon oxide with nanometer scale accuracy of absolute depth levels. An accuracy of less than 1nm standard deviation in t-SPL is achieved by providing an accurate physical model of the writing process to a model-based implementation of a closed-loop lithography process. For transfering the pattern to a target substrate we optimized the etch process and demonstrate linear amplification of grayscale patterns into silicon and silicon oxide with amplification ratios of ∼6 and ∼1, respectively. The performance of the entire process is demonstrated by manufacturing photonic molecules of desired interaction strength. Excellent agreement of fabricated and simulated structures has been achieved.

Fabrication of ten-fold photonic quasicrystalline structures

Directory of Open Access Journals (Sweden)

XiaoHong Sun

2015-05-01

Full Text Available Compared to periodic crystals, quasicrystals have higher point group symmetry and are more favorable in achieving complete band-gaps. In this report, a top-cut prism interferometer is designed to fabricate ten-fold photonic quasicrystalline structures. By optimizing the exposing conditions and material characteristics, appropriate quasicrystals have been obtained in the SU8 photoresist films. Atomic Force Microscopy and laser diffraction are used to characterize the fabricated structures. The measurement results show the consistence between the theoretical design and experiments. This will provide guidance for the large-area and fast production of ten-fold quasicrystalline structures with high quality.

Facile fabrication of a superhydrophobic fabric with mechanical stability and easy-repairability.

Science.gov (United States)

Zhu, Xiaotao; Zhang, Zhaozhu; Yang, Jin; Xu, Xianghui; Men, Xuehu; Zhou, Xiaoyan

2012-08-15

The poor mechanical stability of superhydrophobic fabrics severely hindered their use in practical applications. Herein, to address this problem, we fabricated a superhydrophobic fabric with both mechanical stability and easy-repairability by a simple method. The mechanical durability of the obtained superhydrophobic fabric was evaluated by finger touching and abrasion with sandpaper. The results show that rough surface textures of the fabric were retained, and the fabric surface still exhibited superhydrophobicity after tests. More importantly, when the fabric lost its superhydrophobicity after a long-time abrasion, it can be easily rendered with superhydrophobicity once more by a regeneration process. Copyright © 2012 Elsevier Inc. All rights reserved.

Material engineering to fabricate rare earth erbium thin films for exploring nuclear energy sources

Science.gov (United States)

Banerjee, A.; Abhilash, S. R.; Umapathy, G. R.; Kabiraj, D.; Ojha, S.; Mandal, S.

2018-04-01

High vacuum evaporation and cold-rolling techniques to fabricate thin films of the rare earth lanthanide-erbium have been discussed in this communication. Cold rolling has been used for the first time to successfully fabricate films of enriched and highly expensive erbium metal with areal density in the range of 0.5-1.0 mg/cm2. The fabricated films were used as target materials in an advanced nuclear physics experiment. The experiment was designed to investigate isomeric states in the heavy nuclei mass region for exploring physics related to nuclear energy sources. The films fabricated using different techniques varied in thickness as well as purity. Methods to fabricate films with thickness of the order of 0.9 mg/cm2 were different than those of 0.4 mg/cm2 areal density. All the thin films were characterized using multiple advanced techniques to accurately ascertain levels of contamination as well as to determine their exact surface density. Detailed fabrication methods as well as characterization techniques have been discussed.

Preparation of Au cone for fast ignition target

International Nuclear Information System (INIS)

Du Kai; Zhou Lan; Zhang Lin; Wan Xiaobo; Xiao Jiang

2005-01-01

Cone-shell target is typically used for the fast ignition experiments of inertial confinement fusion. In order to fabricate cone-shell target the Au cones with different angles were produced by electroplating and precise machining. The Au electroplating process was introduced in the paper, and the dependence of coating quality on the parameters, such as composition, temperature, pH of electroplating bath, current density and tip effect, were discussed. (author)

Fabrication and characterization of jute fabrics reinforced polypropylene-based composites: effects of ionizing radiation and disaccharide (sucrose)

Science.gov (United States)

Sahadat Hossain, Md.; Uddin, Muhammad B.; Razzak, Md.; Sarwaruddin Chowdhury, A. M.; Khan, Ruhul A.

2017-12-01

Composites were prepared successfully by compression molding technique using jute fabrics (reinforcing agent) and polypropylene (matrix). Jute fabrics were treated with disaccharide (sucrose) solution and composites were fabricated with the treated fabric and polypropylene. The fiber content of the prepared composites was 40% by weight. It was found that the sucrose (2% solution) decreased the tensile strength (TS) and elongation at break about 6% and 37%, respectively, but tensile modulus and impact strength improved about 27% and 32%, respectively. When gamma radiation was applied through the untreated and treated composites the mechanical properties were improved much higher in non-treated Jute/PP-based composites than that of sucrose treated composites. For 5.0 kGy gamma dose the highest mechanical properties were observed for non-treated composites. At 5.0 kGy gamma dose the improvement of TS was 14% and 2% for non-treated and sucrose treated composites, respectively. The water uptake property of the sucrose treated composites was performed up to 10 days and composites absorbed 18% water. The functional groups of the both composites were analyzed by Fourier transform infrared spectroscopy machine. The scanning electron microscopic images of the both composites were taken for the surface and fiber adhesion analysis.

Investigation of methods for fabricating, characterizing, and transporting cryogenic inertial-confinement-fusion tartets

Energy Technology Data Exchange (ETDEWEB)

Fanning, J.J.; Kim, K.

1981-01-01

The objective of this work is to investigate methods for fabricating, characterizing and transporting cryogenic inertial confinement fusion targets on a continuous basis. A microprocessor-based data acquisition system has been built that converts a complete target image to digital data, which are then analyzed by automated software procedures. The low temperatures required to freeze the hydrogen isotopes contained in a target is provided by a cryogenic cold chamber capable of attaining 15 K. A new method for target manipulation and positioning is studied that employs molecular gas beams to levitate a target and an electrostatic quadrupole structure to provide for its lateral containment. Since the electrostatic target-positioning scheme requires that the targets be charged, preliminary investigation has been carried out for a target-charging mechanism based on ion-bombardment.

Investigation of methods for fabricating, characterizing, and transporting cryogenic inertial-confinement-fusion tartets

International Nuclear Information System (INIS)

Fanning, J.J.; Kim, K.

1981-01-01

The objective of this work is to investigate methods for fabricating, characterizing and transporting cryogenic inertial confinement fusion targets on a continuous basis. A microprocessor-based data acquisition system has been built that converts a complete target image to digital data, which are then analyzed by automated software procedures. The low temperatures required to freeze the hydrogen isotopes contained in a target is provided by a cryogenic cold chamber capable of attaining 15 K. A new method for target manipulation and positioning is studied that employs molecular gas beams to levitate a target and an electrostatic quadrupole structure to provide for its lateral containment. Since the electrostatic target-positioning scheme requires that the targets be charged, preliminary investigation has been carried out for a target-charging mechanism based on ion-bombardment

Electroless plating technology of integral hohlraum Cu target

International Nuclear Information System (INIS)

Liu Jiguang; Fu Qu; Wan Xiaobo; Zhou Lan; Xiao Jiang

2005-01-01

The electroless plating method of making integral hohlraum Cu target and corrosion-resistant technology of target's surface were researched. The actual process was as follows, choosing plexiglass (PMMA) as arbor, taking cationic activation and electroless plating Cu on the arbor surface, taking arbor surface passivation and chemical etching by C 6 H 5 N 3 solution. The technology is easy to realize and its cost is lower, so it is of great reference value for fabricating other integral hohlraum metal or alloy targets used for inertial confinement fusion study. (author)

Perceptual grouping and attention: not all groupings are equal.

Science.gov (United States)

Kimchi, Ruth; Razpurker-Apfeld, Irene

2004-08-01

We examined grouping under inattention using Driver, Davis, Russell, Turatto, & Freeman's (2001) method. On each trial, two successive displays were briefly presented, each comprising a central target square surrounded by elements. The task was to judge whether the two targets were the same or different. The organization of the background elements stayed the same or changed, independently of the targets. In different conditions, background elements grouped into columns/rows by color similarity, a shape (a triangle/arrow, a square/cross, or a vertical/horizontal line) by color similarity, and a shape with no other elements in the background. We measured the influence of the background on the target same-different judgments. The results imply that background elements grouped into columns/rows by color similarity and into a shape when no segregation from other elements was involved and the shape was relatively "good." In contrast, no background grouping was observed when resolving figure-ground relations for segregated units was required, as in grouping into a shape by color similarity. These results suggest that grouping is a multiplicity of processes that vary in their attentional demands. Regardless of attentional demands, the products of grouping are not available to awareness without attention.

Specific emotions as mediators of the effect of intergroup contact on prejudice: findings across multiple participant and target groups.

Science.gov (United States)

Seger, Charles R; Banerji, Ishani; Park, Sang Hee; Smith, Eliot R; Mackie, Diane M

2017-08-01

Emotions are increasingly being recognised as important aspects of prejudice and intergroup behaviour. Specifically, emotional mediators play a key role in the process by which intergroup contact reduces prejudice towards outgroups. However, which particular emotions are most important for prejudice reduction, as well as the consistency and generality of emotion-prejudice relations across different in-group-out-group relations, remain uncertain. To address these issues, in Study 1 we examined six distinct positive and negative emotions as mediators of the contact-prejudice relations using representative samples of U.S. White, Black, and Asian American respondents (N = 639). Admiration and anger (but not other emotions) were significant mediators of the effects of previous contact on prejudice, consistently across different perceiver and target ethnic groups. Study 2 examined the same relations with student participants and gay men as the out-group. Admiration and disgust mediated the effect of past contact on attitude. The findings confirm that not only negative emotions (anger or disgust, based on the specific types of threat perceived to be posed by an out-group), but also positive, status- and esteem-related emotions (admiration) mediate effects of contact on prejudice, robustly across several different respondent and target groups.

The development of uranium foil farication technology utilizing twin roll method for Mo-99 irradiation target

CERN Document Server

Kim, C K; Park, H D

2002-01-01

MDS Nordion in Canada, occupying about 75% of global supply of Mo-99 isotope, has provided the irradiation target of Mo-99 using the rod-type UAl sub x alloys with HEU(High Enrichment Uranium). ANL (Argonne National Laboratory) through co-operation with BATAN in Indonesia, leading RERTR (Reduced Enrichment for Research and Test Reactors) program substantially for nuclear non-proliferation, has designed and fabricated the annular cylinder of uranium targets, and successfully performed irradiation test, in order to develop the fabrication technology of fission Mo-99 using LEU(Low Enrichment Uranium). As the uranium foils could be fabricated in laboratory scale, not in commercialized scale by hot rolling method due to significant problems in foil quality, productivity and economic efficiency, attention has shifted to the development of new technology. Under these circumstances, the invention of uranium foil fabrication technology utilizing twin-roll casting method in KAERI is found to be able to fabricate LEU or...

Electrochemically fabricated polyaniline nanowire-modified electrode for voltammetric detection of DNA hybridization

International Nuclear Information System (INIS)

Zhu Ningning; Chang Zhu; He Pingang; Fang Yuzhi

2006-01-01

A novel and sensitive electrochemical DNA biosensor based on electrochemically fabricated polyaniline nanowire and methylene blue for DNA hybridization detection is presented. Nanowires of conducting polymers were directly synthesized through a three-step electrochemical deposition procedure in an aniline-containing electrolyte solution, by using the glassy carbon electrode (GCE) as the working electrode. The morphology of the polyaniline films was examined using a field emission scanning electron microscope (SEM). The diameters of the nanowires range from 80 to 100 nm. The polyaniline nanowires-coated electrode exhibited very good electrochemical conductivity. Oligonucleotides with phosphate groups at the 5' end were covalently linked onto the amino groups of polyaniline nanowires on the electrode. The hybridization events were monitored with differential pulse voltammetry (DPV) measurement using methylene blue (MB) as an indicator. The approach described here can effectively discriminate complementary from non-complementary DNA sequence, with a detection limit of 1.0 x 10 -12 mol l -1 of complementary target, suggesting that the polyaniline nanowires hold great promises for sensitive electrochemical biosensor applications

Suitability of Secondary PEEK Telescopic Crowns on Zirconia Primary Crowns: The Influence of Fabrication Method and Taper

Directory of Open Access Journals (Sweden)

Susanne Merk

2016-11-01

Full Text Available This study investigates the retention load (RL between ZrO2 primary crowns and secondary polyetheretherketone (PEEK crowns made by different fabrication methods with three different tapers. Standardized primary ZrO2 crowns were fabricated with three different tapers: 0°, 1°, and 2° (n = 10/group. Ten secondary crowns were fabricated (i milled from breCam BioHPP blanks (PM; (ii pressed from industrially fabricated PEEK pellets (PP (BioHPP Pellet; or (iii pressed from granular PEEK (PG (BioHPP Granulat. One calibrated operator adjusted all crowns. In total, the RL of 90 secondary crowns were measured in pull-off tests at 50 mm/min, and each specimen was tested 20 times. Two- and one-way ANOVAs followed by a Scheffé’s post-hoc test were used for data analysis (p < 0.05. Within crowns with a 0° taper, the PP group showed significantly higher retention load values compared with the other groups. Among the 1° taper, the PM group presented significantly lower retention loads than the PP group. However, the pressing type had no impact on the results. Within the 2° taper, the fabrication method had no influence on the RL. Within the PM group, the 2° taper showed significantly higher retention load compared with the 1° taper. The taper with 0° was in the same range value as the 1° and 2° tapers. No impact of the taper on the retention value was observed between the PP groups. Within the PG groups, the 0° taper presented significantly lower RL than the 1° taper, whereas the 2° taper showed no differences. The fabrication method of the secondary PEEK crowns and taper angles showed no consistent effect within all tested groups.

Fabrication and characterization of tungsten and graphite based PFC for divertor target elements of ITER like tokamak application

Energy Technology Data Exchange (ETDEWEB)

Khirwadkar, S.S., E-mail: sameer@ipr.res.in [Institute For Plasma Research, Bhat, Gandhinagar, Gujarat (India); Singh, K.P.; Patil, Y.; Khan, M.S.; Buch, J.J.U.; Patel, Alpesh; Tripathi, Sudhir [Institute For Plasma Research, Bhat, Gandhinagar, Gujarat (India); Jaman, P.M.; Rangaraj, L.; Divakar, C. [Materials Science Division, National Aerospace Laboratories, CSIR, Bangalore, Karnataka (India)

2011-10-15

The development of the fabrication technology of macro-brush configuration of tungsten (W) and carbon (graphite and CFC) plasma facing components (PFCs) for ITER like tokamak application is presented. The fabrication of qualified joint of PFC is a requirement for fusion tokamak. Vacuum brazing method has been employed for joining of W/CuCrZr and C/CuCrZr. Oxygen free high conductivity (OFHC) copper casting on W tiles was performed followed by machining, polishing and ultrasonic cleaning of the samples prior to vacuum brazing. The W/CuCrZr and graphite/CuCrZr based test mockups were vacuum brazed using silver free alloys. The mechanical shear and tensile strengths were evaluated for the W/CuCrZr and graphite/CuCrZr brazed joint samples. The micro-structural examination of the joints showed smooth interface. The details of fabrication and characterization procedure for macro-brush tungsten and carbon based PFC test mockups are presented.

Fabric circuits and method of manufacturing fabric circuits

Science.gov (United States)

Chu, Andrew W. (Inventor); Dobbins, Justin A. (Inventor); Scully, Robert C. (Inventor); Trevino, Robert C. (Inventor); Lin, Greg Y. (Inventor); Fink, Patrick W. (Inventor)

2011-01-01

A flexible, fabric-based circuit comprises a non-conductive flexible layer of fabric and a conductive flexible layer of fabric adjacent thereto. A non-conductive thread, an adhesive, and/or other means may be used for attaching the conductive layer to the non-conductive layer. In some embodiments, the layers are attached by a computer-driven embroidery machine at pre-determined portions or locations in accordance with a pre-determined attachment layout before automated cutting. In some other embodiments, an automated milling machine or a computer-driven laser using a pre-designed circuit trace as a template cuts the conductive layer so as to separate an undesired portion of the conductive layer from a desired portion of the conductive layer. Additional layers of conductive fabric may be attached in some embodiments to form a multi-layer construct.

Biotechnological applications of mobile group II introns and their reverse transcriptases: gene targeting, RNA-seq, and non-coding RNA analysis.

Science.gov (United States)

Enyeart, Peter J; Mohr, Georg; Ellington, Andrew D; Lambowitz, Alan M

2014-01-13

Mobile group II introns are bacterial retrotransposons that combine the activities of an autocatalytic intron RNA (a ribozyme) and an intron-encoded reverse transcriptase to insert site-specifically into DNA. They recognize DNA target sites largely by base pairing of sequences within the intron RNA and achieve high DNA target specificity by using the ribozyme active site to couple correct base pairing to RNA-catalyzed intron integration. Algorithms have been developed to program the DNA target site specificity of several mobile group II introns, allowing them to be made into 'targetrons.' Targetrons function for gene targeting in a wide variety of bacteria and typically integrate at efficiencies high enough to be screened easily by colony PCR, without the need for selectable markers. Targetrons have found wide application in microbiological research, enabling gene targeting and genetic engineering of bacteria that had been intractable to other methods. Recently, a thermostable targetron has been developed for use in bacterial thermophiles, and new methods have been developed for using targetrons to position recombinase recognition sites, enabling large-scale genome-editing operations, such as deletions, inversions, insertions, and 'cut-and-pastes' (that is, translocation of large DNA segments), in a wide range of bacteria at high efficiency. Using targetrons in eukaryotes presents challenges due to the difficulties of nuclear localization and sub-optimal magnesium concentrations, although supplementation with magnesium can increase integration efficiency, and directed evolution is being employed to overcome these barriers. Finally, spurred by new methods for expressing group II intron reverse transcriptases that yield large amounts of highly active protein, thermostable group II intron reverse transcriptases from bacterial thermophiles are being used as research tools for a variety of applications, including qRT-PCR and next-generation RNA sequencing (RNA-seq). The

Fabrication Facilities

Data.gov (United States)

Federal Laboratory Consortium — The Fabrication Facilities are a direct result of years of testing support. Through years of experience, the three fabrication facilities (Fort Hood, Fort Lewis, and...

Engineering structure design and fabrication process of small sized China helium-cooled solid breeder test blanket module

International Nuclear Information System (INIS)

Wang Zeming; Chen Lu; Hu Gang

2014-01-01

Preliminary design and analysis for china helium-cooled solid breeder (CHHC-SB) test blanket module (TBM) have been carried out recently. As partial verification that the original size module was reasonable and the development process was feasible, fabrication work of a small sized module was to be carried out targetedly. In this paper, detailed design and structure analysis of small sized TBM was carried out based on preliminary design work, fabrication process and integrated assembly process was proposed, so a fabrication for the trial engineering of TBM was layed successfully. (authors)

Information on electromagnetic fields and health risk. A developmental project concerning target groups and information instruments

International Nuclear Information System (INIS)

Hannevik, Merete; Reitan, Jon

2000-01-01

On behalf of the Ministry of Health and Social Affairs, the Norwegian Radiation Protection Authority has developed an information package about electromagnetic fields from power lines and mobile phones/base stations. The report describes the process around identification of target groups, cooperation with organizations and independent experts and how this has contributed to the development of the information materials. (Author)

High pressure deuterium-tritium gas target vessels for muon-catalyzed fusion experiments

International Nuclear Information System (INIS)

Caffrey, A.J.; Spaletta, H.W.; Ware, A.G.; Zabriskie, J.M.; Hardwick, D.A.; Maltrud, H.R.; Paciotti, M.A.

1989-01-01

In experimental studies of muon-catalyzed fusion, the density of the hydrogen gas mixture is an important parameter. Catalysis of up to 150 fusions per muon has been observed in deuterium-tritium gas mixtures at liquid hydrogen density; at room temperature, such densities require a target gas pressure of the order of 1000 atmospheres (100 MPa, 15,000 psi). We report here the design considerations for hydrogen gas target vessels for muon-catalyzed fusion experiments that operate at 1000 and 10,000 atmospheres. The 1000 atmosphere high pressure target vessels are fabricated of Type A-286 stainless steel and lined with oxygen-free, high-conductivity (OFHC) copper to provide a barrier to hydrogen permeation of the stainless steel. The 10,000 atmosphere ultrahigh pressure target vessels are made from 18Ni (200 grade) maraging steel and are lined with OFHC copper, again to prevent hydrogen permeation of the steel. In addition to target design features, operating requirements, fabrication procedures, and secondary containment are discussed. 13 refs., 3 figs., 1 tab

Polyester fabric coated with Ag/ZnO composite film by magnetron sputtering

Energy Technology Data Exchange (ETDEWEB)

Yuan, Xiaohong, E-mail: yxhong1981_2004@126.com [Key Laboratory of Eco-Textiles, Ministry of Education, Jiangnan University, Wuxi 214122, Jiangsu (China); Faculty of Clothing and Design, Minjiang University, Fuzhou 350121, Fujian (China); Xu, Wenzheng, E-mail: xwz8199@126.com [Key Laboratory of Eco-Textiles, Ministry of Education, Jiangnan University, Wuxi 214122, Jiangsu (China); Huang, Fenglin, E-mail: windhuang325@163.com [Key Laboratory of Eco-Textiles, Ministry of Education, Jiangnan University, Wuxi 214122, Jiangsu (China); Chen, Dongsheng, E-mail: mjuchen@126.com [Faculty of Clothing and Design, Minjiang University, Fuzhou 350121, Fujian (China); Wei, Qufu, E-mail: qfwei@jiangnan.edu.cn [Key Laboratory of Eco-Textiles, Ministry of Education, Jiangnan University, Wuxi 214122, Jiangsu (China)

2016-12-30

Highlights: • Ag/ZnO composite film was successfully deposited on polyester fabric by magnetron sputtering technique. • Ag film was easily oxidized into Ag{sub 2}O film in high vacuum oxygen environment. • The zinc film coated on the surface of Ag film before RF reactive sputtering could protect the silver film from oxidation. • Polyester fabric coated with Ag/ZnO composite film can obtained structural color. • The anti-ultraviolet and antistatic properties of polyester fabric coated with Ag/ZnO composite film all were good. - Abstract: Ag/ZnO composite film was successfully deposited on polyester fabric by using direct current (DC) magnetron sputtering and radio frequency (RF) magnetron reaction sputtering techniques with pure silver (Ag) and zinc (Zn) targets. X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) were used to examine the deposited film on the fabric. It was found that the zinc film coated on Ag film before RF reactive sputtering could protect the silver film from oxidation. Anti-ultraviolet property and antistatic property of the coated samples using different magnetron sputtering methods were also investigated. The experimental results showed that Ag film was oxidized into in Ag{sub 2}O film in high vacuum oxygen environment. The deposition of Zn film on the surface of the fabric coated with Ag film before RF reactive sputtering, could successfully obtained Ag/ZnO composite film, and also generated structural color on the polyester fabric.

Synthesis of nanosilver on polyamide fabric using silver/ammonia complex.

Science.gov (United States)

Montazer, Majid; Shamei, Ali; Alimohammadi, Farbod

2014-05-01

In this paper, a novel synthesis method for nanosilver has been introduced on or within the polymeric chains of polyamide 6 fabric by using silver/ammonia complex [Ag(NH3)2](+). The silver complex was reduced directly by functional groups of polyamide chains without using any additional chemical reducing agents. The polyamide fabric was also stabilized with formation of new linkages between the polymeric chains of the nylon fabric through silver nanoparticle synthesis. The presence of nanosilver on the fabric was confirmed by UV-vis spectra, EDX patterns and XRD patterns. In addition, X-ray photoelectron spectroscopy (XPS) was utilized to identify the chemical state of silver in a range of silver oxide and silver metal. The SEM images confirmed the presence of nanosilver on the polyamide within the size of 20 and 150 nm. Excellent antibacterial properties were achieved with the treated fabrics against Staphylococcus aureus and Escherichia coli. Further, the antibacterial properties of the polyamide fabric treated with 35 mg/L silver/ammonia were durable against washing as they only decreased to 98.6% after 20 washes. In addition, some other properties of the treated fabrics including color changes, dimensional stability, water droplet adsorption, and reflectance spectrum are reported and thoroughly discussed. Copyright © 2014 Elsevier B.V. All rights reserved.

Simple method to generate and fabricate stochastic porous scaffolds

Energy Technology Data Exchange (ETDEWEB)

Yang, Nan, E-mail: y79nzw@163.com; Gao, Lilan; Zhou, Kuntao

2015-11-01

Considerable effort has been made to generate regular porous structures (RPSs) using function-based methods, although little effort has been made for constructing stochastic porous structures (SPSs) using the same methods. In this short communication, we propose a straightforward method for SPS construction that is simple in terms of methodology and the operations used. Using our method, we can obtain a SPS with functionally graded, heterogeneous and interconnected pores, target pore size and porosity distributions, which are useful for applications in tissue engineering. The resulting SPS models can be directly fabricated using additive manufacturing (AM) techniques. - Highlights: • Random porous structures are constructed based on their regular counterparts. • Functionally graded random pores can be constructed easily. • The scaffolds can be directly fabricated using additive manufacturing techniques.

One size fits all? Policy instruments should fit the segments of target groups

International Nuclear Information System (INIS)

Egmond, Cees; Lulofs, Kris

2005-01-01

In order to meet the Kyoto CO 2 reduction targets, technical innovations in the field of energy-efficiency must be diffused more rapidly and on a larger market scale. Markets develop gradually however, especially if innovations are involved. Diffusion starts with the innovators and early adopters (the early market), followed by the mainstream market (the early and late majority), and ends with the laggards. The actors in these markets differ in their willingness to adopt innovations: the early market actors have a visionary attitude, and the mainstream actors are more pragmatic. In order to choose policy instruments that will most effectively influence these two markets within the target group of housing association, we addressed the following two questions. (1) What are the differences between the early and mainstream markets actors from a behavioural change point of view, and (2) in what way do existing policy instruments differ in influencing the behaviour of these actors? We analysed early market and mainstream decision-making behaviour, and how the active ingredients in policy instruments specifically target the characteristics of the two markets. Mainstream instruments should intervene as early as possible in the decision-making process and emphasise communication about advantages such as comfort and quality in addition to money and energy savings, and present energy conservation as a solution to an actual problem. Instead of bureaucratic subsidy systems for the mainstream, the motto should be 'cash on the barrelhead'. Early market actors are highly internally motivated, implying that early market interventions have to be challenging and facilitating

One size fits all? Policy instruments should fit the segments of target groups

International Nuclear Information System (INIS)

Egmond, C.; Jonkers, R.; Kok, G.

2006-01-01

In order to meet the Kyoto CO 2 reduction targets, technical innovations in the field of energy-efficiency must diffuse more rapidly into a larger market. However, markets develop gradually, especially if innovations are involved. Diffusion starts with the early market (innovators and early adopters), followed by the mainstream market (the early and late majority), and ends with the laggards. The actors in these markets differ in their willingness to adopt innovations; the early market actors have a visionary attitude, and the mainstream market actors are more pragmatic. In order to choose policy instruments that will most effectively influence these two markets within the target group of housing association, we addressed the following two questions. (1) What are the differences between the early and mainstream market actors from a behavioural-change point of view? (2) In what way do existing policy instruments differ in influencing the behaviour of these actors? We analyzed early market and mainstream decision-making behaviours, and how the active ingredients in policy instruments specifically target the characteristics of the two markets. Mainstream instruments should intervene as early as possible in the decision-making process and emphasize communication about advantages such as comfort and quality in addition to money and energy savings. Furthermore, they should present energy conservation as a solution to an actual problem. Instead of bureaucratic subsidy systems for the mainstream, the motto should be 'cash on the barrel-head'. Early market actors are highly internally motivated, implying that early market interventions have to be challenging and facilitating

Diffuse plasma treatment of polyamide 66 fabric in atmospheric pressure air

International Nuclear Information System (INIS)

Li, Lee; Peng, Ming-yang; Teng, Yun; Gao, Guozhen

2016-01-01

Graphical abstract: - Highlights: • A cylindrical-electrode nanosecond-pulse diffuse-discharge reactor is presented. • Large-scale non-thermal plasmas were generated steadily in atmospheric air. • Treated PA66 fabric is etched with oxygen-containing group increases. • The hydrophily of treated PA66 fabric improves effectively. • Extending the treatment time is a method to reduce the treatment frequency. - Abstract: The polyamide 66 (PA66) fabrics are hard to be colored or glued in industrial production due to the poor hydrophily. Diffuse plasma is a kind of non-thermal plasma generated at atmospheric pressure in air. This paper proposes that large-scale diffuse plasma generated between wire electrodes can be employed for improving the hydrophily of PA66 fabrics. A repetitive nanosecond-pulse diffuse-discharge reactor using a cylindrical wire electrode configuration is presented, which can generate large-scale non-thermal plasmas steadily at atmospheric pressure without any barrier dielectric. Then the reactor is used to treat PA66 fabrics in different discharge conditions. The hydrophilicity property of modified PA66 is measured by wicking test method. The modified PA66 is also analyzed by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) to prove the surface changes in physical microstructure and chemical functional groups, respectively. What's more, the effects of treatment time and treatment frequency on surface modification are investigated and discussed.

Fabrication drawings of fuel pins for FUJI project among PSI, JNC and NRG. Revised version 2

International Nuclear Information System (INIS)

Ozawa, Takayuki; Nakazawa, Hiroaki; Abe, Tomoyuki; Nagayama, Masahiro

2002-10-01

Irradiation tests and post-irradiation examinations in the framework of JNC-PSI-NRG collaboration project will be performed in 2003-2005. Irradiation fuel pins will be fabricated by the middle of 2003. The fabrication procedure for irradiation fuel pins has been started in 2001. Several fabrication tests and qualification tests in JNC and PSI (Paul Scherrer Institut, Switzerland) have been performed before the fuel pin fabrication. According to the design assignment between PSI and JNC in the frame of this project, PSI should make specification documents for the fuel pellet, the sphere-pac fuel particles, the vipac fuel fragments, and the fuel segment fabrication. JNC should make the fabrication drawings for irradiation pins. JNC has been performed the fuel design in cooperation with PSI and NRG (Nuclear Research and Consultancy Group, Holland). In this project, the pelletized fuel, the sphere-pac fuel, and the vipac fuel will be simultaneously irradiated on HFR (High Flux Reactor, Holland). The fabrication drawings have been made under the design assignment with PSI, and consist of the drawings of MOX pellet, thermal insulator pellet, pin components, fuel segments, and the constructed pin. The fabrication drawings were approved in October 2001, but after that, the optimization of specifications was discussed and agreed among all partners. According to this agreement, the fabrication drawings were revised in January 2002. After the earlier revision, the shape of particle retainer to be made by PSI was modified from its drawing beforehand delivered. In this report, the fabrication drawings revised again will be shown, and the fabrication procedure (welding Qualification Tests) will be modified in accordance with the result of discussion on the 3rd technical meeting held in September 2002. These design works have been performed in Fuel Design and Evaluation Group, Plutonium Fuel Fabrication Division, Plutonium Fuel Center under the commission of Plutonium Fuel

Recent developments in laser-fusion target coatings

International Nuclear Information System (INIS)

Fries, R.J.; Catlett, D.S.; Fossey, D.; Mayer, A.; McCreary, W.J.; Powell, B.W.; Simonsic, G.A.

1976-01-01

Techniques to fabricate hollow, spherical, multilayered laser-fusion targets are described. The first is a glow discharge polymerization process for plastic coating. A chemical vapor deposition process for depositing Mo/Re alloys is also discussed along with some new techniques for electrodeless plating and for electroplating a wide variety of metals

Sulfonation of polyester fabrics by gaseous sulfur oxide activated by UV irradiation

International Nuclear Information System (INIS)

Kordoghli, Bessem; Khiari, Ramzi; Mhenni, Mohamed Farouk; Sakli, Faouzi; Belgacem, Mohamed Naceur

2012-01-01

Highlights: ► In this paper, an original technique was present to improve the hydrophilic properties of polyester fibres. ► The modification of PET fabric was carried out using gaseous sulfur trioxide activated by UV irradiations. ► We fully characterized the modified and untreated fabrics. - Abstract: This paper describes an original technique aiming to improve the hydrophilic properties of polyester fibres. In this method, the sulfonation of the aromatic rings is carried out using gaseous sulfur trioxide activated by UV irradiations. Thus, exposing the polyester textile fabric to the UVC light (wavelength around 254 nm) under a stream of sulfur trioxide leads to the fixation of -SO 3 H groups. The amounts of the fixed sulfonate groups depended on the reaction conditions. Evidence of grafting deduced from the measurements of hygroscopic properties was carried out by contact angle measurement, moisture regain as well as by measuring the rate of retention. SEM and FT-IR analysis, DSC and DTA/TGA thermograms showed that no significant modifications have occurred in the bulk of the treated PET fabrics.

Target size matters: target errors contribute to the generalization of implicit visuomotor learning.

Science.gov (United States)

Reichenthal, Maayan; Avraham, Guy; Karniel, Amir; Shmuelof, Lior

2016-08-01

The process of sensorimotor adaptation is considered to be driven by errors. While sensory prediction errors, defined as the difference between the planned and the actual movement of the cursor, drive implicit learning processes, target errors (e.g., the distance of the cursor from the target) are thought to drive explicit learning mechanisms. This distinction was mainly studied in the context of arm reaching tasks where the position and the size of the target were constant. We hypothesize that in a dynamic reaching environment, where subjects have to hit moving targets and the targets' dynamic characteristics affect task success, implicit processes will benefit from target errors as well. We examine the effect of target errors on learning of an unnoticed perturbation during unconstrained reaching movements. Subjects played a Pong game, in which they had to hit a moving ball by moving a paddle controlled by their hand. During the game, the movement of the paddle was gradually rotated with respect to the hand, reaching a final rotation of 25°. Subjects were assigned to one of two groups: The high-target error group played the Pong with a small ball, and the low-target error group played with a big ball. Before and after the Pong game, subjects performed open-loop reaching movements toward static targets with no visual feedback. While both groups adapted to the rotation, the postrotation reaching movements were directionally biased only in the small-ball group. This result provides evidence that implicit adaptation is sensitive to target errors. Copyright © 2016 the American Physiological Society.

Direct characterization of cotton fabrics treated with di-epoxide by nuclear magnetic resonance.

Science.gov (United States)

Xiao, Min; Chéry, Joronia; Keresztes, Ivan; Zax, David B; Frey, Margaret W

2017-10-15

A non-acid-based, di-functional epoxide, neopentyl glycol diglycidyl ether (NPGDGE), was used to modify cotton fabrics. Direct characterization of the modified cotton was conducted by Nuclear Magnetic Resonance (NMR) without grinding the fabric into a fine powder. NaOH and MgBr 2 were compared in catalyzing the reaction between the epoxide groups of NPGDGE and the hydroxyl groups of cellulose. Possible reaction routes were discussed. Scanning electron microscopy (SEM) images showed that while the MgBr 2 -catalyzed reaction resulted in self-polymerization of NPGDGE, the NaOH-catalyzed reaction did not. Fourier transform infrared spectroscopy (FTIR) showed that at high NaOH concentration cellulose restructures from allomorph I to II. NMR studies verified the incorporation of NPGDGE into cotton fabrics with a clear NMR signal, and confirmed that at higher NaOH concentration the efficiency of grafting of NPGDGE was increased. This demonstrates that use of solid state NMR directly on woven fabric samples can simultaneously characterize chemical modification and crystalline polymorph of cotton. No loss of tensile strength was observed for cotton fabrics modified with NPGDGE. Copyright © 2017 Elsevier Ltd. All rights reserved.

An investigation on preparation of CIGS targets by sintering process

Energy Technology Data Exchange (ETDEWEB)

Zhang Ning, E-mail: zhn98@126.co [Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China); Zhuang Daming; Zhang Gong [Department of Mechanical Engineering, Tsinghua University, Beijing 100084 (China)

2010-01-15

Pressureless sintering process was used to fabricate CIGS targets with Cu{sub 2}Se, In{sub 2}Se{sub 3}, and Ga{sub 2}Se{sub 3} as raw powders mixed according to the stoichiometry of CuIn{sub 0.72}Ga{sub 0.28}Se{sub 2} (CIGS). The results showed that only CuIn{sub 0.7}Ga{sub 0.3}Se{sub 2} phase can be detected in the sintered targets. The pores in sintered specimen become smaller and distribute more homogeneously under the conditions of finer powders and higher cold pressure. Both mass loss caused by the formation of volatile phase relating to Ga and volume expansion occur during the sintering process, which result in the decrease of density. The tendency of anti-densification becomes stronger under the conditions of coarser powders and higher cold pressure. The sintering process and causes for anti-densification were discussed. Finally, a hot pressing process was carried out, which was proved to be fairly effective to increase the density of CIGS target. The fabricated target can be used for magnetron-sputtering deposition of CIGS absorbers.

Progress on LMJ targets for ignition

Energy Technology Data Exchange (ETDEWEB)

Cherfils-Clerouin, C; Boniface, C; Bonnefille, M; Dattolo, E; Galmiche, D; Gauthier, P; Giorla, J; Laffite, S; Liberatore, S; Loiseau, P; Malinie, G; Masse, L; Masson-Laborde, P E; Monteil, M C; Poggi, F; Seytor, P; Wagon, F; Willien, J L, E-mail: catherine.cherfils@cea.f [CEA, DAM, DIF, F-91297 Arpajon (France)

2009-12-15

Targets designed to produce ignition on the Laser Megajoule (LMJ) are being simulated in order to set specifications for target fabrication. The LMJ experimental plans include the attempt of ignition and burn of an ICF capsule with 160 laser beams, delivering up to 1.4 MJ and 380 TW. New targets needing reduced laser energy with only a small decrease in robustness have then been designed for this purpose. Working specifically on the coupling efficiency parameter, i.e. the ratio of the energy absorbed by the capsule to the laser energy, has led to the design of a rugby-ball shaped cocktail hohlraum; with these improvements, a target based on the 240-beam A1040 capsule can be included in the 160-beam laser energy-power space. Robustness evaluations of these different targets shed light on critical points for ignition, which can trade off by tightening some specifications or by preliminary experimental and numerical tuning experiments.

Progress on LMJ targets for ignition

International Nuclear Information System (INIS)

Cherfils-Clerouin, C; Boniface, C; Bonnefille, M; Dattolo, E; Galmiche, D; Gauthier, P; Giorla, J; Laffite, S; Liberatore, S; Loiseau, P; Malinie, G; Masse, L; Masson-Laborde, P E; Monteil, M C; Poggi, F; Seytor, P; Wagon, F; Willien, J L

2009-01-01

Targets designed to produce ignition on the Laser Megajoule (LMJ) are being simulated in order to set specifications for target fabrication. The LMJ experimental plans include the attempt of ignition and burn of an ICF capsule with 160 laser beams, delivering up to 1.4 MJ and 380 TW. New targets needing reduced laser energy with only a small decrease in robustness have then been designed for this purpose. Working specifically on the coupling efficiency parameter, i.e. the ratio of the energy absorbed by the capsule to the laser energy, has led to the design of a rugby-ball shaped cocktail hohlraum; with these improvements, a target based on the 240-beam A1040 capsule can be included in the 160-beam laser energy-power space. Robustness evaluations of these different targets shed light on critical points for ignition, which can trade off by tightening some specifications or by preliminary experimental and numerical tuning experiments.

Fabrication of 121Sb isotopic targets for the study of nuclear high spin features

Science.gov (United States)

Devi, K. Rojeeta; Kumar, Suresh; Kumar, Neeraj; Abhilash, S. R.; Kabiraj, D.

2018-06-01

Isotopic 121Sb targets with 197Au backing have been prepared by Physical Vapor Deposition (PVD) method using the diffusion pump based coating unit at target laboratory, Inter University Accelerator Centre (IUAC), New Delhi, India. The target thickness was measured by stylus profilo-meter and the purity of the targets was investigated by Energy Dispersive X-ray Analysis (EDXA). One of these targets has been used in an experiment which was performed at IUAC for nuclear structure study through fusion evaporation reaction. The excitation function of the 121Sb(12C, yxnγ) reaction has been performed for energies 58 to 70 MeV in steps of 4 MeV. The experimental results were compared with the calculations of statistical models : PACE4 and CASCADE. The methods adopted to achieve best quality foils and good deposition efficiency are reported in this paper.

Development of IFE target systems on the NIF

International Nuclear Information System (INIS)

Schultz, K.R.; Fagaly, R.L.; Bernat, T.; Meier, W.; Petzoldt, R.; Foreman, L.

1995-01-01

The Target Systems session of the Workshop on NIF Experiments for IFE developed a list of critical issues for inertial fusion energy (IFE) target systems, and considered the potential of the National Ignition Facility (NIF) to help in the resolution of these issues and in the development of IFE target systems. This paper describes the IFE Target System issues, categorized into target fabrication issues and target transport issues, describes potential NIF IFE target systems experiments, considers the impact of these experiments on the NIF and discusses the development required before these experiments could be done. Most target systems issues must be resolved by development in the laboratory, not in the NIF, and some must be resolved before the NIF can be successful. However, experiments done in the NIF could play a valuable role in developing target systems for IFE. These experiments should have modest impact on the basic design of the NIF, but could require several hundred dedicated, high yield shots

Fabrication of high-quality single-crystal Cu thin films using radio-frequency sputtering.

Science.gov (United States)

Lee, Seunghun; Kim, Ji Young; Lee, Tae-Woo; Kim, Won-Kyung; Kim, Bum-Su; Park, Ji Hun; Bae, Jong-Seong; Cho, Yong Chan; Kim, Jungdae; Oh, Min-Wook; Hwang, Cheol Seong; Jeong, Se-Young

2014-08-29

Copper (Cu) thin films have been widely used as electrodes and interconnection wires in integrated electronic circuits, and more recently as substrates for the synthesis of graphene. However, the ultra-high vacuum processes required for high-quality Cu film fabrication, such as molecular beam epitaxy (MBE), restricts mass production with low cost. In this work, we demonstrated high-quality Cu thin films using a single-crystal Cu target and radio-frequency (RF) sputtering technique; the resulting film quality was comparable to that produced using MBE, even under unfavorable conditions for pure Cu film growth. The Cu thin film was epitaxially grown on an Al2O3 (sapphire) (0001) substrate, and had high crystalline orientation along the (111) direction. Despite the 10(-3) Pa vacuum conditions, the resulting thin film was oxygen free due to the high chemical stability of the sputtered specimen from a single-crystal target; moreover, the deposited film had >5× higher adhesion force than that produced using a polycrystalline target. This fabrication method enabled Cu films to be obtained using a simple, manufacturing-friendly process on a large-area substrate, making our findings relevant for industrial applications.

Suitability of Secondary PEEK Telescopic Crowns on Zirconia Primary Crowns: The Influence of Fabrication Method and Taper.

Science.gov (United States)

Merk, Susanne; Wagner, Christina; Stock, Veronika; Eichberger, Marlis; Schmidlin, Patrick R; Roos, Malgorzata; Stawarczyk, Bogna

2016-11-08

This study investigates the retention load (RL) between ZrO₂ primary crowns and secondary polyetheretherketone (PEEK) crowns made by different fabrication methods with three different tapers. Standardized primary ZrO₂ crowns were fabricated with three different tapers: 0°, 1°, and 2° ( n = 10/group). Ten secondary crowns were fabricated (i) milled from breCam BioHPP blanks (PM); (ii) pressed from industrially fabricated PEEK pellets (PP) (BioHPP Pellet); or (iii) pressed from granular PEEK (PG) (BioHPP Granulat). One calibrated operator adjusted all crowns. In total, the RL of 90 secondary crowns were measured in pull-off tests at 50 mm/min, and each specimen was tested 20 times. Two- and one-way ANOVAs followed by a Scheffé's post-hoc test were used for data analysis ( p impact on the results. Within the 2° taper, the fabrication method had no influence on the RL. Within the PM group, the 2° taper showed significantly higher retention load compared with the 1° taper. The taper with 0° was in the same range value as the 1° and 2° tapers. No impact of the taper on the retention value was observed between the PP groups. Within the PG groups, the 0° taper presented significantly lower RL than the 1° taper, whereas the 2° taper showed no differences. The fabrication method of the secondary PEEK crowns and taper angles showed no consistent effect within all tested groups.

Readiness Review of BWXT for Fabrication of AGR 5/6/7 Compacts

Energy Technology Data Exchange (ETDEWEB)

Marshall, Douglas William [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sharp, Michelle Tracy [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-02-01

In support of preparations for fabricating compacts for the Advanced Gas Reactor (AGR) fuel qualification irradiation experiments (AGR-5/6/7), Idaho National Laboratory (INL) conducted a readiness review of the BWX Technology (BWXT) procedures, processes, and equipment associated with compact fabrication activities at the BWXT Nuclear Operations Group (BWXT-NOG) facility outside Lynchburg, VirginiaVA. The readiness review used quality assurance requirements taken from the American Society of Mechanical Engineers (ASME) Nuclear Quality Assurance Standard (NQA-1-2008/1a-2009) as a basis to assess readiness to start compact fabrication.

Fabrication and characterisation of composite targets for the transmutation of actinides

International Nuclear Information System (INIS)

Naestren, C.; Haas, D.; Fernandez, A.; Somers, J.

2006-01-01

Transmutation of transuranic elements separated from spent fuel is a way to reduce the toxicity of long-lived nuclides in the waste before disposal. Plutonium and the minor actinides (MA) are reintroduced into the fuel cycle for further irradiation and incineration. Currently CERMET fuel forms, in which a ceramic actinide is dispersed in a matrix, are considered for MA transmutation. In a first step, PuO 2 beads are produced by a sol gel method in which a Pu nitrate solution is converted to solid, dust-free, particles. These porous beads are then infiltrated with an americium nitrate solution to the incipient wetness point and calcined to give the (PuAm)O 2 beads, which are blended with a metal matrix and compacted and sintered to form the final fuel pellet. The matrix used is molybdenum due to its high thermal conductivity and low neutron capture cross section, if it is enriched in 92 Mo. In this work, optimization of the bead porosity is investigated to achieve a higher Am content by infiltration. Addition of carbon to the mother solution in the sol gel step increases the bead porosity but it also changes both bead and final fuel pellet microstructure. A surrogate fuel, with cerium simulating the actinides has been fabricated and its mechanical stability and bead characteristics investigated as a function of carbon content and thermal treatment. The characterization of the surrogate fuel by ceramography, density, porosity, bead-quality, etc., is a necessary step in the process optimization, to be transferred to the production of the actinide samples. This process is now at an advanced stage and is being used for the production of fuels for irradiation tests in the Phenix (Futurix) and HFR-Petten (HELIOS) reactors. In parallel, studies on the dissolution of the fuel pellets, with the aim of dissolving the Mo-matrix while keeping the CeO 2 beads intact, have been initiated. Thus, Mo can be recycled for further fuel fabrication either from production scraps or from

Digital fabrication

CERN Document Server

2012-01-01

The Winter 2012 (vol. 14 no. 3) issue of the Nexus Network Journal features seven original papers dedicated to the theme “Digital Fabrication”. Digital fabrication is changing architecture in fundamental ways in every phase, from concept to artifact. Projects growing out of research in digital fabrication are dependent on software that is entirely surface-oriented in its underlying mathematics. Decisions made during design, prototyping, fabrication and assembly rely on codes, scripts, parameters, operating systems and software, creating the need for teams with multidisciplinary expertise and different skills, from IT to architecture, design, material engineering, and mathematics, among others The papers grew out of a Lisbon symposium hosted by the ISCTE-Instituto Universitario de Lisboa entitled “Digital Fabrication – A State of the Art”. The issue is completed with four other research papers which address different mathematical instruments applied to architecture, including geometric tracing system...

Activity targets for nanostructured platinum-group-metal-free catalysts in hydroxide exchange membrane fuel cells

Science.gov (United States)

Setzler, Brian P.; Zhuang, Zhongbin; Wittkopf, Jarrid A.; Yan, Yushan

2016-12-01

Fuel cells are the zero-emission automotive power source that best preserves the advantages of gasoline automobiles: low upfront cost, long driving range and fast refuelling. To make fuel-cell cars a reality, the US Department of Energy has set a fuel cell system cost target of US$30 kW-1 in the long-term, which equates to US$2,400 per vehicle, excluding several major powertrain components (in comparison, a basic, but complete, internal combustion engine system costs approximately US$3,000). To date, most research for automotive applications has focused on proton exchange membrane fuel cells (PEMFCs), because these systems have demonstrated the highest power density. Recently, however, an alternative technology, hydroxide exchange membrane fuel cells (HEMFCs), has gained significant attention, because of the possibility to use stable platinum-group-metal-free catalysts, with inherent, long-term cost advantages. In this Perspective, we discuss the cost profile of PEMFCs and the advantages offered by HEMFCs. In particular, we discuss catalyst development needs for HEMFCs and set catalyst activity targets to achieve performance parity with state-of-the-art automotive PEMFCs. Meeting these targets requires careful optimization of nanostructures to pack high surface areas into a small volume, while maintaining high area-specific activity and favourable pore-transport properties.

Target developments program to prepare LMJ campaigns

Energy Technology Data Exchange (ETDEWEB)

Collier, R; Bachelet, F; Botrel, R; Breton, O; Chicanne, C; Dauteuil, C H; Durut, F; Fleury, E; Guillot, L; Hermerel, C; Jeannot, L; Legaie, O; Legay, G; Martin, M; Reneaume, B; Theobald, M; Vincent-Viry, O, E-mail: remy.collier@cea.f [Commissariat a l' Energie Atomique, Direction des Applications Militaires, Valduc, F-21120 Is-sur-Tille (France)

2010-08-01

To carry out laser plasma experiments on CEA laser facilities, a R and D program was set up and is still under way to deliver complex targets. For a decade, specific developments are also dedicated to 'Ligne d'Integration Laser' (LIL) in France and Omega facilities (USA). To prepare the targets intended for the first experiments on the Laser 'Megajoule' (LMJ) facility, new developments are required, such as cocktail hohlraum fabrication, gas barrier coating and foam shells developments. For fusion experiments on LMJ, an important program is also under way to elaborate the Cryogenic Target Assembly (CTA), to fill and transport the CTA and to study the conformation process of the DT layer.

Fabric based supercapacitor

International Nuclear Information System (INIS)

Yong, S; Tudor, M J; Beeby, S P; Owen, J R

2013-01-01

Flexible supercapacitors with electrodes coated on inexpensive fabrics by the dipping technique. This paper present details of the design, fabrication and characterisation of fabric supercapacitor. The sandwich structured supercapacitors can achieve specific capacitances of 11.1F/g, area capacitance 105 mF.cm −2 and maintain 95% of the initial capacitance after cycling the device for more than 15000 times

Video-based Learning Versus Traditional Method for Preclinical Course of Complete Denture Fabrication.

Science.gov (United States)

Fayaz, Amir; Mazahery, Azita; Hosseinzadeh, Mohammad; Yazdanpanah, Samane

2015-03-01

Advances in computer science and technology allow the instructors to use instructional multimedia programs to enhance the process of learning for dental students. The purpose of this study was to determine the effect of a new educational modality by using videotapes on the performance of dental students in preclinical course of complete denture fabrication. This quasi-experimental study was performed on 54 junior dental students in Shahid Beheshti University of Medical Sciences (SBMU). Twenty-five and 29 students were evaluated in two consecutive semesters as controls and cases, respectively for the same course. The two groups were matched in terms of "knowledge about complete denture fabrication" and "basic dental skills" using a written test and a practical exam, respectively. After the intervention, performance and clinical skills of students were assessed in 8 steps. Eventually, a post-test was carried out to find changes in knowledge and skills of students in this regard. In the two groups with the same baseline level of knowledge and skills, independent T-test showed that students in the test group had a significantly superior performance in primary impression taking (p= 0.001) and primary cast fabrication (p= 0.001). In terms of anterior teeth set up, students in the control group had a significantly better performance (p= 0.001). Instructional videotapes can aid in teaching fabrication of complete denture and are as effective as the traditional teaching system.

Implant overdentures: dental students' performance in fabrication, denture quality, and patient satisfaction.

Science.gov (United States)

Aragon, Cecilia E; Cornacchio, Angelica Lee Petrina; Ibarra, Lilia Marcela; Saad, Muhammed N; Zibrowski, Elaine

2010-09-01

The purpose of this study was to evaluate dental students' performance when fabricating a mandibular two-implant overdenture (OD) as compared to conventional dentures (CD) and to determine if these prostheses were successful. Twenty students and twenty patients were divided into two groups: complete denture group (CDG) and maxillary denture and two-implant OD group (ODG). Students' progress was evaluated at each appointment as they were given a clinical assessment score (CAS), which varied from 1 (unacceptable, needs to repeat procedure) to 4 (acceptable, no errors). The success of the prosthesis was evaluated by the patients using a visual analog scale (VAS) and an expert (a prosthodontist) using a denture quality assessment (DQA) form. Performance for both groups was not statistically different across all eight appointments (CDG 3.16 versus ODG 3.25; p=0.46). Patients with ODs reported greater stability with their dentures (p=0.048) and greater ability to chew than patients with CDs (p=0.03). There were no differences between the groups in terms of expert appraisal (ODG 71.1 versus CDG 67.5; p=0.59). The performance of dental students when fabricating a two-implant OD is thus not different from that of a CD. Students can successfully fabricate a two-implant OD as perceived by both patients and prosthodontists.

Polyamine/salt-assembled microspheres coated with hyaluronic acid for targeting and pH sensing.

Science.gov (United States)

Zhang, Pan; Yang, Hui; Wang, Guojun; Tong, Weijun; Gao, Changyou

2016-06-01

The poly(allylamine hydrochloride)/trisodium citrate aggregates were fabricated and further covalently crosslinked via the coupling reaction of carboxylic sites on trisodium citrate with the amine groups on polyamine, onto which poly-L-lysine and hyaluronic acid were sequentially assembled, forming stable microspheres. The pH sensitive dye and pH insensitive dye were further labeled to enable the microspheres with pH sensing property. Moreover, these microspheres could be specifically targeted to HeLa tumor cells, since hyaluronic acid can specifically recognize and bind to CD44, a receptor overexpressed on many tumor cells. Quantitative pH measurement by confocal laser scanning microscopy demonstrated that the microspheres were internalized into HeLa cells, and accumulated in acidic compartments. By contrast, only a few microspheres were adhered on the NIH 3T3 cells surface. The microspheres with combined pH sensing property and targeting ability can enhance the insight understanding of the targeted drug vehicles trafficking after cellular internalization. Copyright © 2016 Elsevier B.V. All rights reserved.

Pulsed-laser-deposited YBCO thin films using modified MTG processed targets

CERN Document Server

Kim, C H; Kim, I T; Hahn, T S

1999-01-01

YBCO thin films were deposited by pulsed laser deposition from targets fabricated using the modified melt-textured growth (MTG) method and the solid-state sintering (SSS) method. All of the films showed c-axis orientations, but the films from the MTG targets had better crystallinity than those from the SSS targets. As the substrate temperature was increased, T sub c and J sub c of the films increased. The films from the MTG targets showed better superconducting properties than those from the SSS targets. From the composition analysis of the targets, the Y-richer vapor species arriving at the substrate from the MTG targets are thought to form a thermodynamically more stable YBCO phase with less cation disorder.

Peripheral Contour Grouping and Saccade Targeting: The Role of Mirror Symmetry

Directory of Open Access Journals (Sweden)

Michaël Sassi

2014-01-01

Full Text Available Integrating shape contours in the visual periphery is vital to our ability to locate objects and thus make targeted saccadic eye movements to efficiently explore our surroundings. We tested whether global shape symmetry facilitates peripheral contour integration and saccade targeting in three experiments, in which observers responded to a successful peripheral contour detection by making a saccade towards the target shape. The target contours were horizontally (Experiment 1 or vertically (Experiments 2 and 3 mirror symmetric. Observers responded by making a horizontal (Experiments 1 and 2 or vertical (Experiment 3 eye movement. Based on an analysis of the saccadic latency and accuracy, we conclude that the figure-ground cue of global mirror symmetry in the periphery has little effect on contour integration or on the speed and precision with which saccades are targeted towards objects. The role of mirror symmetry may be more apparent under natural viewing conditions with multiple objects competing for attention, where symmetric regions in the visual field can pre-attentively signal the presence of objects, and thus attract eye movements.

Sulfonation of polyester fabrics by gaseous sulfur oxide activated by UV irradiation

Energy Technology Data Exchange (ETDEWEB)

Kordoghli, Bessem [Laboratory of Applied Chemical and Environment (UR-CAE) - University of Monastir (Tunisia); Textile Research Laboratory (LRT) - ISET Kasr Hellal, University of Monastir (Tunisia); Khiari, Ramzi, E-mail: khiari_ramzi2000@yahoo.fr [Laboratory of Applied Chemical and Environment (UR-CAE) - University of Monastir (Tunisia); LGP2 - Laboratory of Pulp and Paper Science, 461, Rue de la Papeterie - BP 65, 38402 Saint Martin d' Heres Cedex (France); Mhenni, Mohamed Farouk [Laboratory of Applied Chemical and Environment (UR-CAE) - University of Monastir (Tunisia); Sakli, Faouzi [Textile Research Laboratory (LRT) - ISET Kasr Hellal, University of Monastir (Tunisia); Belgacem, Mohamed Naceur [LGP2 - Laboratory of Pulp and Paper Science, 461, Rue de la Papeterie - BP 65, 38402 Saint Martin d' Heres Cedex (France)

2012-10-01

Highlights: Black-Right-Pointing-Pointer In this paper, an original technique was present to improve the hydrophilic properties of polyester fibres. Black-Right-Pointing-Pointer The modification of PET fabric was carried out using gaseous sulfur trioxide activated by UV irradiations. Black-Right-Pointing-Pointer We fully characterized the modified and untreated fabrics. - Abstract: This paper describes an original technique aiming to improve the hydrophilic properties of polyester fibres. In this method, the sulfonation of the aromatic rings is carried out using gaseous sulfur trioxide activated by UV irradiations. Thus, exposing the polyester textile fabric to the UVC light (wavelength around 254 nm) under a stream of sulfur trioxide leads to the fixation of -SO{sub 3}H groups. The amounts of the fixed sulfonate groups depended on the reaction conditions. Evidence of grafting deduced from the measurements of hygroscopic properties was carried out by contact angle measurement, moisture regain as well as by measuring the rate of retention. SEM and FT-IR analysis, DSC and DTA/TGA thermograms showed that no significant modifications have occurred in the bulk of the treated PET fabrics.

Fabrication of cotton fabric with superhydrophobicity and flame retardancy.

Science.gov (United States)

Zhang, Ming; Wang, Chengyu

2013-07-25

A simple and facile method for fabricating the cotton fabric with superhydrophobicity and flame retardancy is described in the present work. The cotton fabric with the maximal WCA of 160° has been prepared by the covalent deposition of amino-silica nanospheres and the further graft with (heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane. The geometric microstructure of silica spheres was measured by transmission electron microscopy (TEM). The cotton textiles before and after treatment were characterized by using scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The wetting behavior of cotton samples was investigated by water contact angle measurement. Moreover, diverse performances of superhydrophobic cotton textiles have been evaluated as well. The results exhibited the outstanding superhydrophobicity, excellent waterproofing durability and flame retardancy of the cotton fabric after treatment, offering a good opportunity to accelerate the large-scale production of superhydrophobic textiles materials for new industrial applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

Mars 2020 Rover SHERLOC Calibration Target

Science.gov (United States)

Graff, Trevor; Fries, Marc; Burton, Aaron; Ross, Amy; Larson, Kristine; Garrison, Dan; Calaway, Mike; Tran, Vinh; Bhartia, Roh; Beegle, Luther

2016-01-01

The Scanning Habitable Environments with Raman & Luminescence for Organics & Chemicals (SHERLOC) instrument is a deep ultraviolet (UV) Raman Fluorescence instrument selected as part of the Mars 2020 rover instrument suite. SHERLOC will be mounted on the rover arm and its primary role is to identify carbonaceous species in martian samples. The SHERLOC instrument requires a calibration target which is being designed and fabricated at JSC as part of our continued science participation in Mars robotic missions. The SHERLOC calibration target will address a wide range of NASA goals to include basic science of interest to both the Science Mission Directorate and Human Exploration and Operations Mission Directorate.

Nuclear Fabrication Consortium

Energy Technology Data Exchange (ETDEWEB)

Levesque, Stephen [EWI, Columbus, OH (United States)

2013-04-05

This report summarizes the activities undertaken by EWI while under contract from the Department of Energy (DOE) Office of Nuclear Energy (NE) for the management and operation of the Nuclear Fabrication Consortium (NFC). The NFC was established by EWI to independently develop, evaluate, and deploy fabrication approaches and data that support the re-establishment of the U.S. nuclear industry: ensuring that the supply chain will be competitive on a global stage, enabling more cost-effective and reliable nuclear power in a carbon constrained environment. The NFC provided a forum for member original equipment manufactures (OEM), fabricators, manufacturers, and materials suppliers to effectively engage with each other and rebuild the capacity of this supply chain by : Identifying and removing impediments to the implementation of new construction and fabrication techniques and approaches for nuclear equipment, including system components and nuclear plants. Providing and facilitating detailed scientific-based studies on new approaches and technologies that will have positive impacts on the cost of building of nuclear plants. Analyzing and disseminating information about future nuclear fabrication technologies and how they could impact the North American and the International Nuclear Marketplace. Facilitating dialog and initiate alignment among fabricators, owners, trade associations, and government agencies. Supporting industry in helping to create a larger qualified nuclear supplier network. Acting as an unbiased technology resource to evaluate, develop, and demonstrate new manufacturing technologies. Creating welder and inspector training programs to help enable the necessary workforce for the upcoming construction work. Serving as a focal point for technology, policy, and politically interested parties to share ideas and concepts associated with fabrication across the nuclear industry. The report the objectives and summaries of the Nuclear Fabrication Consortium

Targeting the Psychosexual Challenges Faced by Couples with Breast Cancer: Can Couples Group Psychotherapy Help?

Science.gov (United States)

Lagana, Luciana; Fobair, Patricia; Spiegel, David

2014-11-01

The need for the psychosexual rehabilitation of breast cancer survivors and their intimate partners is underscored by the high prevalence of multiple psychosexual difficulties encountered by this patient population. Concerns about health, sexuality, and emotional distress are common among women with breast cancer and are often related to the side effects of cancer treatment. Additionally, both intimate relationship problems and partners' distress are likely to influence patients' psychosexual health. A clearer understanding of these complex clinical issues is needed in order to implement effective psychosexual rehabilitation interventions. In this article, we extended the use of the manualized and empirically validated Supportive-Expressive Group Therapy (SEGT) model to target the specific psychosexual needs of couples with breast (as well as other types of) cancer. In view of the pertinent literature in this area and based on our clinical experience utilizing this group therapy model with different patient populations, we have discussed how clinicians involved in the psychosexual care of oncology patients could apply such a model within a couples group therapy format.

Occupational Home Economics Education Series. Fabrics and Textiles Merchandising. Competency Based Teaching Module.

Science.gov (United States)

Martin, Ruth

This module, one of ten competency based modules developed for vocational home economics teachers, is based on a job cluster in fabric and textiles merchandising. It is designed for use with a variety of groups including grades 9-14 and adults. Focusing on the specific job title fabric and textiles salesperson, ten competencies and the student…

Proceedings of JSPS-CAS core university program seminar on target materials

International Nuclear Information System (INIS)

Gu, Z.Z.; Norimatsu, T.

2008-02-01

China-Japan Bilateral Collaboration on the Study of Ultrahigh Density Plasma has been established since 2001 and its second phase is conducting from 2006. Target materials are key issue of the Study of Ultrahigh Density Plasma, and the second of target fabrication was opened at the 2005 Workshop on Ultrahigh Density Plasma Production, Application and theory for Laser Fusion at Nine Village Valley, Sichuan. It achieved great successes in high-level academic exchange and efficient presentation of state-of-the-art development in this research field. However, in order to attract greater attention and participation of more scientists in these fields, the organizing committee decided to further specify and enlarge the scale of the workshop to be China-Japan Bilateral Seminar on Target Materials 2007 in Huang Shan in southern Anhui Province of east China. The seminar had more than 20 participants from 7 universities and 3 institutes in Japan and China. They exchanged state-of-the-art development in nanomaterials, capsule fabrication and low density materials toward target of high power laser. This issue is the collection of the paper presented at the seminar. The 17 of the presented papers are indexed individually. (J.P.N.)

A target group-specific approach to ''green'' power retailing: students as consumers of renewable energy

International Nuclear Information System (INIS)

Gossling, S.; Kunkel, T.; Schumacher, K.; Heck, N.; Birkemeyer, J.; Froese, J.; Naber, N.; Schliermann, E.

2005-01-01

An extensive body of literature exists on the obstacles that have to be overcome in green power retailing. In this article, target group-specific marketing is evaluated as a strategy to increase the share of residential customers of green power. A sample of students in the city of Freiburg, Germany was interviewed in order to assess their awareness of environmental issues, their willingness to change to green power products, and to better understand individual hindrances in changing the power supplier. The analysis shows that students are highly positive towards green power products, but for several reasons difficult to reach in marketing campaigns. Aspects to be considered in addressing this consumer-group include the students' particular expectations towards green products, their living-conditions, price sensitivity, and their perception of the relative effort involved in changing the power provider. (author)

The mechanical and thermal characteristics of phenolic foam reinforced with kaolin powder and glass fiber fabric

Science.gov (United States)

Xiao, Wenya; Huang, Zhixiong; Ding, Jie

2017-12-01

In this work, kaolin powder and glass fiber fabric were added to PF in order to improve its thermal stability and mechanical property. Micro-structures of carbonized PF with kaolin powder were inspected by scanning electron microscopy (SEM) to demonstrate the filler’s pinning effect. SEM results illustrated modified PF had well morphology after high-temperature heat treatment. The Fourier transform infrared spectrometer (FTIR) test was carried out and found that kaolin powder only physically dispersed in PF. The compression test and thermal weight loss test were done on two groups of modified PF (Group A: add powder and fabric; Group B: add powder only). Results showed that all modified PF were better than pure PF, while foams with powder and fabric showed better mechanical characteristic and thermal stability compared with foams with powder only.

New polymorphous computing fabric

International Nuclear Information System (INIS)

Wolinski, Christophe; Gokhale, Maya; McCabe, Kevin P.

2002-01-01

This paper introduces a new polymorphous computing Fabric well suited to DSP and Image Processing and describes its implementation on a Configurable System on a Chip (CSOC). The architecture is highly parameterized and enables customization of the synthesized Fabric to achieve high performance for a specific class of application. For this reason it can be considered to be a generic model for hardware accelerator synthesis from a high level specification. Another important innovation is the Fabric uses a global memory concept, which gives the host processor random access to all the variables and instructions on the Fabric. The Fabric supports different computing models including MIMD, SPMD and systolic flow and permits dynamic reconfiguration. We present a specific implementation of a bank of FIR filters on a Fabric composed of 52 cells on the Altera Excalibur ARM running at 33 MHz. The theoretical performance of this Fabric is 1.8 GMACh. For the FIR application we obtain 1.6 GMAC/s real performance. Some automatic tools have been developed like the tool to provide a host access utility and assembler.

Secure Automated Fabrication: an overview of remote breeder fuel fabrication

International Nuclear Information System (INIS)

Nyman, D.H.; Graham, R.A.

1983-10-01

The Secure Automated Fabrication (SAF) line is an automated, remotely controlled breeder fuel pin fabrication process which is to be installed in the Fuels and Materials Examination Facility (FMEF). The FMEF is presently under construction at Hanford and is scheduled for completion in 1984. The SAF line is scheduled for startup in 1987 and will produce mixed uranium-plutonium fuel pins for the Fast Flux Test Facility (FFTF) and the Clinch River Breeder Reactor Plant (CRBRP). The fabrication line and support systems are described

Design and fabrication of self-powered in-core neutron flux monitor assembly

International Nuclear Information System (INIS)

Chung, M.K.; Cho, S.W.; Kang, H.D.; Cho, K.K.; Cho, B.S.; Kang, S.S.

1980-01-01

This is the final report on the prototypical fabrication of an in-core neutron flux monitor detector assembly for a specific power reactor conducted by KAERI from July 1, 1978 to December 31, 1979. It is well known that power reactors require a large number of in-core neutron flux detector for reactor regulation and the structures of detector assemblies are different from reactor to reactor. Therefore, from the nature of this project, it should be noted here that the target model of the prototypical farbrication of an in-core neutron flux monitor detector assembly is a VFD-2 System for Wolsung CANDU. It is concluded that fabrication of in-core neutron flux monitor detector assembly for CANDU reactor is technically feasible and will bring economical benefit as much as 50 % of the unit price if they are fabricated in Korea by using partially materials which are available from local market. (author)

Fabric Reconstruction Based on Sustainable Development: Take the Type of Fabric Recycling as an Example

Directory of Open Access Journals (Sweden)

Zhangting Guan

2017-07-01

Full Text Available Sustainable development is a very important concept of our time, it wants to do is to live in harmony with people, to protect the environment where our human survival. Fabric recycling refers to the use of a variety of traditional and high-tech means of the existing fabric fabric design and processing. So that the surface of a rich visual texture and tactile texture "through the fabric recycling approach. However, the fabric form and clothing design coordination between the clothing design is essential to the link! Garment fabric is not only the material basis of clothing modeling But also an important form of plastic arts. Fabric recycling art has gradually become a new breakthrough point of fashion design! And become an important means to increase the added value of clothing products. But at the same time fabric recycling also follow the concept of sustainable development. This paper analyzes the relationship between fabric reengineering and sustainable development. Combined with practice to explore the fabric processing technology and its creative ideas and some of its environmental performance.

Single-step laser-based fabrication and patterning of cell-encapsulated alginate microbeads

International Nuclear Information System (INIS)

Kingsley, D M; Dias, A D; Corr, D T; Chrisey, D B

2013-01-01

Alginate can be used to encapsulate mammalian cells and for the slow release of small molecules. Packaging alginate as microbead structures allows customizable delivery for tissue engineering, drug release, or contrast agents for imaging. However, state-of-the-art microbead fabrication has a limited range in achievable bead sizes, and poor control over bead placement, which may be desired to localize cellular signaling or delivery. Herein, we present a novel, laser-based method for single-step fabrication and precise planar placement of alginate microbeads. Our results show that bead size is controllable within 8%, and fabricated microbeads can remain immobilized within 2% of their target placement. Demonstration of this technique using human breast cancer cells shows that cells encapsulated within these microbeads survive at a rate of 89.6%, decreasing to 84.3% after five days in culture. Infusing rhodamine dye into microbeads prior to fluorescent microscopy shows their 3D spheroidal geometry and the ability to sequester small molecules. Microbead fabrication and patterning is compatible with conventional cellular transfer and patterning by laser direct-write, allowing location-based cellular studies. While this method can also be used to fabricate microbeads en masse for collection, the greatest value to tissue engineering and drug delivery studies and applications lies in the pattern registry of printed microbeads. (paper)

Design and Fabrication of DebriSat - A Representative LEO Satellite for Improvements to Standard Satellite Breakup Models

Science.gov (United States)

Clark, S.; Dietrich, A.; Fitz-Coy, N.; Weremeyer, M.; Liou, J.-C.

2012-01-01

This paper discusses the design and fabrication of DebriSat, a 50 kg satellite developed to be representative of a modern low Earth orbit satellite in terms of its components, materials used, and fabrication procedures. DebriSat will be the target of a future hypervelocity impact experiment to determine the physical characteristics of debris generated after an on-orbit collision of a modern LEO satellite. The major ground-based satellite impact experiment used by DoD and NASA in their development of satellite breakup models was SOCIT, conducted in 1992. The target used for that experiment was a Navy transit satellite (40 cm, 35 kg) fabricated in the 1960's. Modern satellites are very different in materials and construction techniques than those built 40 years ago. Therefore, there is a need to conduct a similar experiment using a modern target satellite to improve the fidelity of the satellite breakup models. To ensure that DebriSat is truly representative of typical LEO missions, a comprehensive study of historical LEO satellite designs and missions within the past 15 years for satellites ranging from 1 kg to 5000 kg was conducted. This study identified modern trends in hardware, material, and construction practices utilized in recent LEO missions. Although DebriSat is an engineering model, specific attention is placed on the quality, type, and quantity of the materials used in its fabrication to ensure the integrity of the outcome. With the exception of software, all other aspects of the satellite s design, fabrication, and assembly integration and testing will be as rigorous as that of an actual flight vehicle. For example, to simulate survivability of launch loads, DebriSat will be subjected to a vibration test. As well, the satellite will undergo thermal vacuum tests to verify that the components and overall systems meet typical environmental standards. Proper assembly and integration techniques will involve comprehensive joint analysis, including the precise

Production and characterization of thin 7Li targets fabricated by ion implantation

International Nuclear Information System (INIS)

Cruz, J.; Fonseca, M.; Luis, H.; Mateus, R.; Marques, H.; Jesus, A.P.; Ribeiro, J.P.; Teodoro, O.M.N.D.; Rolfs, C.

2009-01-01

Very high fluence implantation of 7 Li + ions was used to promote the formation of a thin and high density 7 Li target in the surface region of Al samples. The implanted volume was characterized by particle induced gamma-ray emission, Rutherford backscattering spectrometry, X-ray photoelectron spectroscopy and nuclear reaction analysis, revealing that the implanted surface is a combination of Li 2 CO 3 , metallic lithium, LiOH and C, with almost no Al present. Radiation damage effects by proton beams were studied by observing the evolution of the 7 Li(p, α) 4 He nuclear reaction yield with the accumulated charge, at different proton energies, revealing high stability of the produced Li target.

Optimum processing parameters for the fabrication of twill flax fabric-reinforced polypropylene (PP) composites

Science.gov (United States)

Zuhudi, Nurul Zuhairah Mahmud; Minhat, Mulia; Shamsuddin, Mohd Hafizi; Isa, Mohd Dali; Nur, Nurhayati Mohd

2017-12-01

In recent years, natural fabric thermoplastic composites such as flax have received much attention due to its attractive capabilities for structural applications. It is crucial to study the processing of flax fabric materials in order to achieve good quality and cost-effectiveness in fibre reinforced composites. Though flax fabric has been widely utilized for several years in composite applications due to its high strength and abundance in nature, much work has been concentrated on short flax fibre and very little work focused on using flax fabric. The effectiveness of the flax fabric is expected to give higher strength performance due to its structure but the processing needs to be optimised. Flax fabric composites were fabricated using compression moulding due to its simplicity, gives good surface finish and relatively low cost in terms of labour and production. Further, the impregnation of the polymer into the fabric is easier in this process. As the fabric weave structure contributes to the impregnation quality which leads to the overall performance, the processing parameters of consolidation i.e. pressure, time, and weight fraction of fabric were optimized using the Taguchi method. This optimization enhances the consolidation quality of the composite by improving the composite mechanical properties, three main tests were conducted i.e. tensile, flexural and impact test. It is observed that the processing parameter significantly affected the consolidation and quality of composite.

Double electrochemical covalent coupling method based on click chemistry and diazonium chemistry for the fabrication of sensitive amperometric immunosensor.

Science.gov (United States)

Qi, Honglan; Li, Min; Zhang, Rui; Dong, Manman; Ling, Chen

2013-08-20

A double electrochemical covalent coupling method based on click chemistry and diazonium chemistry for the fabrication of sensitive amperometric immunosensor was developed. As a proof-of-concept, a designed alkyne functionalized human IgG was used as a capture antibody and a HRP-labeled rabbit anti-goat IgG was used as signal antibody for the determination of the anti-human IgG using the sandwich model. The immunosensor was fabricated by electrochemically grafting a phenylazide on the surface of a glassy carbon electrode, and then, by coupling the alkyne functionalized human IgG with the phenylazide group through an electro-click chemistry in the presence of Cu(II). The amperometric measurement for the determination of the anti-human IgG was performed after the fabricated immunosensor was incubated with the target anti-human IgG and then with the HRP-labeled anti-goat IgG at -0.25V in 0.10M PBS (pH 7.0) containing 0.1mM hydroquinone and 2.0mM H2O2. The results showed that the increased current was linear with the logarithm of the concentration of the anti-human IgG in the range from 1.0×10(-10)g mL(-1) to 1.0×10(-8)g mL(-1) with a detection limit of 3×10(-11)g mL(-1). Furthermore, the feasibility of the double electrochemical covalent coupling method proposed in this work for fabricating the amperometric immunosensor array was explored. This work demonstrates that the double electrochemical covalent coupling method is a promising approach for the fabrication of the immunosensor and immunosensor array. Copyright © 2013 Elsevier B.V. All rights reserved.

Fabrication of three-dimensional scaffolds using precision extrusion deposition with an assisted cooling device.

Science.gov (United States)

Hamid, Q; Snyder, J; Wang, C; Timmer, M; Hammer, J; Guceri, S; Sun, W

2011-09-01

In the field of biofabrication, tissue engineering and regenerative medicine, there are many methodologies to fabricate a building block (scaffold) which is unique to the target tissue or organ that facilitates cell growth, attachment, proliferation and/or differentiation. Currently, there are many techniques that fabricate three-dimensional scaffolds; however, there are advantages, limitations and specific tissue focuses of each fabrication technique. The focus of this initiative is to utilize an existing technique and expand the library of biomaterials which can be utilized to fabricate three-dimensional scaffolds rather than focusing on a new fabrication technique. An expanded library of biomaterials will enable the precision extrusion deposition (PED) device to construct three-dimensional scaffolds with enhanced biological, chemical and mechanical cues that will benefit tissue generation. Computer-aided motion and extrusion drive the PED to precisely fabricate micro-scaled scaffolds with biologically inspired, porosity, interconnectivity and internal and external architectures. The high printing resolution, precision and controllability of the PED allow for closer mimicry of tissues and organs. The PED expands its library of biopolymers by introducing an assisting cooling (AC) device which increases the working extrusion temperature from 120 to 250 °C. This paper investigates the PED with the integrated AC's capabilities to fabricate three-dimensional scaffolds that support cell growth, attachment and proliferation. Studies carried out in this paper utilized a biopolymer whose melting point is established to be 200 °C. This polymer was selected to illustrate the newly developed device's ability to fabricate three-dimensional scaffolds from a new library of biopolymers. Three-dimensional scaffolds fabricated with the integrated AC device should illustrate structural integrity and ability to support cell attachment and proliferation.

Fabrication of three-dimensional scaffolds using precision extrusion deposition with an assisted cooling device

International Nuclear Information System (INIS)

Hamid, Q; Snyder, J; Wang, C; Guceri, S; Sun, W; Timmer, M; Hammer, J

2011-01-01

In the field of biofabrication, tissue engineering and regenerative medicine, there are many methodologies to fabricate a building block (scaffold) which is unique to the target tissue or organ that facilitates cell growth, attachment, proliferation and/or differentiation. Currently, there are many techniques that fabricate three-dimensional scaffolds; however, there are advantages, limitations and specific tissue focuses of each fabrication technique. The focus of this initiative is to utilize an existing technique and expand the library of biomaterials which can be utilized to fabricate three-dimensional scaffolds rather than focusing on a new fabrication technique. An expanded library of biomaterials will enable the precision extrusion deposition (PED) device to construct three-dimensional scaffolds with enhanced biological, chemical and mechanical cues that will benefit tissue generation. Computer-aided motion and extrusion drive the PED to precisely fabricate micro-scaled scaffolds with biologically inspired, porosity, interconnectivity and internal and external architectures. The high printing resolution, precision and controllability of the PED allow for closer mimicry of tissues and organs. The PED expands its library of biopolymers by introducing an assisting cooling (AC) device which increases the working extrusion temperature from 120 to 250 deg. C. This paper investigates the PED with the integrated AC's capabilities to fabricate three-dimensional scaffolds that support cell growth, attachment and proliferation. Studies carried out in this paper utilized a biopolymer whose melting point is established to be 200 deg. C. This polymer was selected to illustrate the newly developed device's ability to fabricate three-dimensional scaffolds from a new library of biopolymers. Three-dimensional scaffolds fabricated with the integrated AC device should illustrate structural integrity and ability to support cell attachment and proliferation.

International light water nuclear fuel fabrication supply. Are fabrication services assured?

International Nuclear Information System (INIS)

Rothwell, Geoffrey

2010-01-01

This paper examines the cost structure of fabricating light water reactor (LWR) fuel with low-enriched uranium (LEU, with less than 5% enrichment). The LWR-LEU fuel industry is decades old, and (except for the high entry cost of designing and licensing a fuel fabrication facility and its fuel), labor and additional fabrication lines can be added at Nth-of-a-Kind cost to the maximum capacity allowed by a site license. The industry appears to be competitive: nuclear fuel fabrication capacity is assured with many competitors and reasonable prices. However, nuclear fuel assurance has become an important issue for nations now to considering new nuclear power plants. To provide this assurance many proposals equate 'nuclear fuel banks' (which would require fuel for specific reactors) with 'LEU banks' (where LEU could be blended into nuclear fuel with the proper enrichment) with local fuel fabrication. The policy issues (which are presented, but not answered in this paper) become (1) whether the construction of new nuclear fuel fabrication facilities in new nuclear power nations could lead to the proliferation of nuclear weapons, and (2) whether nuclear fuel quality can be guaranteed under current industry arrangements, given that fuel failure at one reactor can lead to forced shutdowns at many others. (author)

Fabrication of Ultrasensitive Field-Effect Transistor DNA Biosensors by a Directional Transfer Technique Based on CVD-Grown Graphene.

Science.gov (United States)

Zheng, Chao; Huang, Le; Zhang, Hong; Sun, Zhongyue; Zhang, Zhiyong; Zhang, Guo-Jun

2015-08-12

Most graphene field-effect transistor (G-FET) biosensors are fabricated through a routine process, in which graphene is transferred onto a Si/SiO2 substrate and then devices are subsequently produced by micromanufacture processes. However, such a fabrication approach can introduce contamination onto the graphene surface during the lithographic process, resulting in interference for the subsequent biosensing. In this work, we have developed a novel directional transfer technique to fabricate G-FET biosensors based on chemical-vapor-deposition- (CVD-) grown single-layer graphene (SLG) and applied this biosensor for the sensitive detection of DNA. A FET device with six individual array sensors was first fabricated, and SLG obtained by the CVD-growth method was transferred onto the sensor surface in a directional manner. Afterward, peptide nucleic acid (PNA) was covalently immobilized on the graphene surface, and DNA detection was realized by applying specific target DNA to the PNA-functionalized G-FET biosensor. The developed G-FET biosensor was able to detect target DNA at concentrations as low as 10 fM, which is 1 order of magnitude lower than those reported in a previous work. In addition, the biosensor was capable of distinguishing the complementary DNA from one-base-mismatched DNA and noncomplementary DNA. The directional transfer technique for the fabrication of G-FET biosensors is simple, and the as-constructed G-FET DNA biosensor shows ultrasensitivity and high specificity, indicating its potential application in disease diagnostics as a point-of-care tool.

Fabrication challenges for indium phosphide microsystems

International Nuclear Information System (INIS)

Siwak, N P; Fan, X Z; Ghodssi, R

2015-01-01

From the inception of III–V microsystems, monolithically integrated device designs have been the motivating drive for this field, bringing together the utility of single-chip microsystems and conventional fabrication techniques. Indium phosphide (InP) has a particular advantage of having a direct bandgap within the low loss telecommunication wavelength (1550 nm) range, able to support passive waveguiding and optical amplification, detection, and generation depending on the exact alloy of In, P, As, Ga, or Al materials. Utilizing epitaxy, one can envision the growth of a substrate that contains all of the components needed to establish a single-chip optical microsystem, containing detectors, sources, waveguides, and mechanical structures. A monolithic InP MEMS system has, to our knowledge, yet to be realized due to the significant difficulties encountered when fabricating the integrated devices. In this paper we present our own research and consolidate findings from other research groups across the world to give deeper insight into the practical aspects of InP monolithic microsystem development: epitaxial growth of InP-based alloys, etching techniques, common MEMS structures realized in InP, and future applications. We pay special attention to shedding light on considerations that must be taken when designing and fabricating a monolithic InP MEMS device. (topical review)

Preparation of homogeneous isotopic targets with rotating substrate

International Nuclear Information System (INIS)

Xu, G.J.; Zhao, Z.G.

1993-01-01

Isotopically enriched accelerator targets were prepared using the evaporation-condensation method from a resistance heating crucible. For high collection efficiency and good homogeneity the substrate was rotated at a vertical distance of 1.3 to 2.5 cm from the evaporation source. Measured collection efficiencies were 13 to 51 μg cm -2 mg -1 and homogeneity tests showed values close to the theoretically calculated ones for a point source. Targets, selfsupporting or on backings, could be fabricated with this method for elements and some compounds with evaporation temperatures up to 2300 K. (orig.)

Eco-friendly surface modification on polyester fabrics by esterase treatment

Energy Technology Data Exchange (ETDEWEB)

Wu, Jindan; Cai, Guoqiang; Liu, Jinqiang; Ge, Huayun; Wang, Jiping, E-mail: jipingwanghz@gmail.com

2014-03-01

Graphical abstract: - Highlights: • We used a simple and easy way to measure the enzyme activity. • We studied the mechanism by characterizing the chemical changes in the surface of fabric. • We studied the advantages in surface wettability, fiber integrity and mechanical performance of cutinase treated fabrics. • Cutinase pretreated fibers exhibited much improved fabric wicking and better fiber integrity comparing to alkali treated ones. • Cutinase pretreatment technology promotes energy conservation and emission reduction. - Abstract: Currently, traditional alkali deweighting technology is widely used to improve the hydrophilicity of polyester fabrics. However, the wastewater and heavy chemicals in the effluent cause enormous damage to the environment. Esterase treatment, which is feasible in mild conditions with high selectivity, can provide a clean and efficient way for polyester modification. Under the optimum conditions, the polyester fabric hydrolysis process of esterase had a linear kinetics. X-ray photoelectron spectrometry (XPS) results showed that hydroxyl and carboxyl groups were produced only on the surface of modified fiber without changing the chemical composition of the bulk. These fibers exhibited much improved fabric wicking, as well as greatly improved oily stain removal performance. Compared to the harsh alkali hydrolysis, the enzyme treatment led to smaller weight loss and better fiber integrity. The esterase treatment technology is promising to produce higher-quality polyester textiles with an environmental friendly approach.

Functionalized single-walled carbon nanotube-based fuel cell benchmarked against US DOE 2017 technical targets.

Science.gov (United States)

Jha, Neetu; Ramesh, Palanisamy; Bekyarova, Elena; Tian, Xiaojuan; Wang, Feihu; Itkis, Mikhail E; Haddon, Robert C

2013-01-01

Chemically modified single-walled carbon nanotubes (SWNTs) with varying degrees of functionalization were utilized for the fabrication of SWNT thin film catalyst support layers (CSLs) in polymer electrolyte membrane fuel cells (PEMFCs), which were suitable for benchmarking against the US DOE 2017 targets. Use of the optimum level of SWNT -COOH functionality allowed the construction of a prototype SWNT-based PEMFC with total Pt loading of 0.06 mg(Pt)/cm²--well below the value of 0.125 mg(Pt)/cm² set as the US DOE 2017 technical target for total Pt group metals (PGM) loading. This prototype PEMFC also approaches the technical target for the total Pt content per kW of power (<0.125 g(PGM)/kW) at cell potential 0.65 V: a value of 0.15 g(Pt)/kW was achieved at 80°C/22 psig testing conditions, which was further reduced to 0.12 g(Pt)/kW at 35 psig back pressure.

Travelling wave resonators fabricated with low-loss hydrogenated amorphous silicon

Science.gov (United States)

Lipka, Timo; Amthor, Julia; Trieu, Hoc Khiem; Müller, Jörg

2013-05-01

Low-loss hydrogenated amorphous silicon is employed for the fabrication of various planar integrated travelling wave resonators. Microring, racetrack, and disk resonators of different dimensions were fabricated with CMOS-compatible processes and systematically investigated. The key properties of notch filter ring resonators as extinction ratio, Q-factor, free spectral range, and the group refractive index were determined for resonators of varying radius, thereby achieving critically coupled photonic systems with high extinction ratios of about 20 dB for both polarizations. Racetrack resonators that are arranged in add/drop configuration and high quality factor microdisk resonators were optically characterized, with the microdisks exhibiting Q-factors of greater than 100000. Four-channel add/drop wavelength-division multiplexing filters that are based on cascaded racetrack resonators are studied. The design, the fabrication, and the optical characterization are presented.

Comparative evaluation of marginal fit and axial wall adaptability of copings fabricated by metal laser sintering and lost-wax technique: An in vitro study.

Science.gov (United States)

Gaikwad, Bhushan Satish; Nazirkar, Girish; Dable, Rajani; Singh, Shailendra

2018-01-01

The present study aims to compare and evaluate the marginal fit and axial wall adaptability of Co-Cr copings fabricated by metal laser sintering (MLS) and lost-wax (LW) techniques using a stereomicroscope. A stainless steel master die assembly was fabricated simulating a prepared crown; 40 replicas of master die were fabricated in gypsum type IV and randomly divided in two equal groups. Group A coping was fabrication by LW technique and the Group B coping fabrication by MLS technique. The copings were seated on their respective gypsum dies and marginal fit was measured using stereomicroscope and image analysis software. For evaluation of axial wall adaptability, the coping and die assembly were embedded in autopolymerizing acrylic resin and sectioned vertically. The discrepancies between the dies and copings were measured along the axial wall on each halves. The data were subjected to statistical analysis using unpaired t -test. The mean values of marginal fit for copings in Group B (MLS) were lower (24.6 μm) than the copings in Group A (LW) (39.53 μm), and the difference was statistically significant ( P adaptability in comparison with copings fabricated by the LW technique. However, the values of marginal fit of copings fabricated that the two techniques were within the clinically acceptable limit (<50 μm).

NIF Target Assembly Metrology Methodology and Results

Energy Technology Data Exchange (ETDEWEB)

Alger, E. T. [General Atomics, San Diego, CA (United States); Kroll, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Dzenitis, E. G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Montesanti, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hughes, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Swisher, M. [IAP, Livermore, CA (United States); Taylor, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Segraves, K. [IAP, Livermore, CA (United States); Lord, D. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Reynolds, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Castro, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Edwards, G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2011-01-01

During our inertial confinement fusion (ICF) experiments at the National Ignition Facility (NIF) we require cryogenic targets at the 1-cm scale to be fabricated, assembled, and metrologized to micron-level tolerances. During assembly of these ICF targets, there are physical dimensmetrology is completed using optical coordinate measurement machines that provide repeatable measurements with micron precision, while also allowing in-process data collection for absolute accuracy in assembly. To date, 51 targets have been assembled and metrologized, and 34 targets have been successfully fielded on NIF relying on these metrology data. In the near future, ignition experiments on NIF will require tighter tolerances and more demanding target assembly and metrology capability. Metrology methods, calculations, and uncertainty estimates will be discussed. Target diagnostic port alignment, target position, and capsule location results will be reviewed for the 2009 Energetics Campaign. The information is presented via control charts showing the effect of process improvements that were made during target production. Certain parameters, including capsule position, met the 2009 campaign specifications but will have much tighter requirements in the future. Finally, in order to meet these new requirements assembly process changes and metrology capability upgrades will be necessary.

Fabrication and Final Field Tuning of Copper Cavity Models for a High-Current SRF ERL at 703.75 MHz

CERN Document Server

Cole, Michael; Burger, Al; Falletta, Michael; Holmes, Douglas; Peterson, Ed; Wong, Robert

2005-01-01

Advanced Energy Systems is currently under contract to BNL to fabricate a five cell superconducting cavity and cryomodule for the RHIC eCooler SRF Energy Recovery Linac (ERL) program.* The cavity is designed and optimized for ampere class SRF ERL service. As part of this program, we have fabricated two low power copper models of the RF cavities. During the fabrication process a series of frequency measurements were made and compared to the frequency expected at that point in the fabrication process. Where possible, the cavity was modified either before or during, the next fabrication step to tune the cavity frequency toward the target frequency. Following completion of the cavities they were tuned for field flatness and frequency. This paper will review the measurements made, frequency tuning performed, and discuss discrepancies between the expected and measured results. We will also review the as fabricated field profiles and the results of the tuning steps. Further, the cost and benefits of extensive in pro...

Fabrication and wireless micromanipulation of magnetic-biocompatible microrobots using microencapsulation for microrobotics and microfluidics applications.

Science.gov (United States)

Li, Hui; Zhang, Jinyong; Zhang, Nannan; Kershaw, Joe; Wang, Lei

2016-12-01

It is important to fabricate biocompatible and chemical-resistant microstructures that can be powered and controlled without a tether in fluid environment for applications when contamination must be avoided, like cell manipulation, and applications where connecting the power source to the actuator would be cumbersome, like targeted delivery of chemicals. In this work, a novel fabrication method was described to encapsulate magnetic composite into pure SU-8 structures, enabling the truly microscale ferromagnetic microrobots biocompatible and chemical resistant. The microrobots were developed using the simple multilayer photolithography that allows us to mass produce and were actuated contact-free by external magnetic field to complete micromanipulations of micro-objects. The microrobots were actuated moving along a preplanned path to transport a glass microsphere object at an approximately average speed of 1.1 mm/sec and can be operated to rotate, aim at targets and collect objects.

Electrolytic coating of microparticles for laser fusion targets

International Nuclear Information System (INIS)

Mayer, A.; Catlett, D.S.

1977-04-01

An electroplating apparatus for applying uniform metallic coatings that have excellent surface finishes to discrete microparticles is described. The device is used to electrodeposit metals onto thin-walled metal, metallized glass, or plastic mandrels. The apparatus and process were developed for fabrication of microsphere pressure vessels to be used as targets in laser fusion research

A facile fabrication of multifunctional knit polyester fabric based on chitosan and polyaniline polymer nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Tang, Xiaoning [College of Textiles, Qingdao University, Qingdao, Shandong 266071 (China); Laboratory of New Fiber Materials and Modern Textile, The Growing Base for State Key Laboratory, Qingdao University, Qingdao, Shandong 266071 (China); Tian, Mingwei [College of Textiles, Qingdao University, Qingdao, Shandong 266071 (China); Laboratory of New Fiber Materials and Modern Textile, The Growing Base for State Key Laboratory, Qingdao University, Qingdao, Shandong 266071 (China); Collaborative Innovation Center for Marine Biomass Fibers, Materials and Textiles of Shandong Province, Qingdao University, Qingdao, Shandong 266071 (China); Qu, Lijun, E-mail: lijunqu@126.com [College of Textiles, Qingdao University, Qingdao, Shandong 266071 (China); Laboratory of New Fiber Materials and Modern Textile, The Growing Base for State Key Laboratory, Qingdao University, Qingdao, Shandong 266071 (China); Collaborative Innovation Center for Marine Biomass Fibers, Materials and Textiles of Shandong Province, Qingdao University, Qingdao, Shandong 266071 (China); Zhu, Shifeng [College of Textiles, Qingdao University, Qingdao, Shandong 266071 (China); Laboratory of New Fiber Materials and Modern Textile, The Growing Base for State Key Laboratory, Qingdao University, Qingdao, Shandong 266071 (China); Guo, Xiaoqing [College of Textiles, Qingdao University, Qingdao, Shandong 266071 (China); Laboratory of New Fiber Materials and Modern Textile, The Growing Base for State Key Laboratory, Qingdao University, Qingdao, Shandong 266071 (China); Collaborative Innovation Center for Marine Biomass Fibers, Materials and Textiles of Shandong Province, Qingdao University, Qingdao, Shandong 266071 (China); Han, Guangting [Laboratory of New Fiber Materials and Modern Textile, The Growing Base for State Key Laboratory, Qingdao University, Qingdao, Shandong 266071 (China); Collaborative Innovation Center for Marine Biomass Fibers, Materials and Textiles of Shandong Province, Qingdao University, Qingdao, Shandong 266071 (China); and others

2014-10-30

Highlights: • Multifunctional knit polyester fabric was facile fabricated by the combination of pad-dry-cure process and in situ chemical polymerization route. • High electrical conductivity and efficient water-repellent properties were endowed to the polymer nanocomposite coated fabric. • The polymer nanocomposite coated fabric also performed efficient and durable photocatalytic activities under the illumination of ultraviolet light. - Abstract: Knit polyester fabric was successively modified and decorated with chitosan layer and polyaniline polymer nanocomposite layer in this paper. The fabric was firstly treated with chitosan to form a stable layer through the pad-dry-cure process, and then the polyaniline polymer nanocomposite layer was established on the outer layer by in situ chemical polymerization method using ammonium persulfate as oxidant and chlorhydric acid as dopant. The surface morphology of coated fabric was characterized by scanning electron microscopy (SEM), and the co-existence of chitosan layer and granular polyaniline polymer nanocomposite was confirmed and well dispersed on the fabric surface. The resultant fabric was endowed with remarkable electrical conductivity properties and efficient water-repellent capability, which also have been found stable after water laundering. In addition, the photocatalytic decomposition activity for reactive red dye was observed when the multifunctional knit polyester fabric was exposed to the illumination of ultraviolet lamp. These results indicated that chitosan and polyaniline polymer nanocomposite could form ideal multifunctional coatings on the surface of knit polyester fabric.

A facile fabrication of multifunctional knit polyester fabric based on chitosan and polyaniline polymer nanocomposite

International Nuclear Information System (INIS)

Tang, Xiaoning; Tian, Mingwei; Qu, Lijun; Zhu, Shifeng; Guo, Xiaoqing; Han, Guangting

2014-01-01

Highlights: • Multifunctional knit polyester fabric was facile fabricated by the combination of pad-dry-cure process and in situ chemical polymerization route. • High electrical conductivity and efficient water-repellent properties were endowed to the polymer nanocomposite coated fabric. • The polymer nanocomposite coated fabric also performed efficient and durable photocatalytic activities under the illumination of ultraviolet light. - Abstract: Knit polyester fabric was successively modified and decorated with chitosan layer and polyaniline polymer nanocomposite layer in this paper. The fabric was firstly treated with chitosan to form a stable layer through the pad-dry-cure process, and then the polyaniline polymer nanocomposite layer was established on the outer layer by in situ chemical polymerization method using ammonium persulfate as oxidant and chlorhydric acid as dopant. The surface morphology of coated fabric was characterized by scanning electron microscopy (SEM), and the co-existence of chitosan layer and granular polyaniline polymer nanocomposite was confirmed and well dispersed on the fabric surface. The resultant fabric was endowed with remarkable electrical conductivity properties and efficient water-repellent capability, which also have been found stable after water laundering. In addition, the photocatalytic decomposition activity for reactive red dye was observed when the multifunctional knit polyester fabric was exposed to the illumination of ultraviolet lamp. These results indicated that chitosan and polyaniline polymer nanocomposite could form ideal multifunctional coatings on the surface of knit polyester fabric

Remarkable enhancement on elimination reaction of side groups in excimer laser ablation of mixture targets of perylene derivatives with metal powder

International Nuclear Information System (INIS)

Nishio, Satoru; Tamura, Kazuyuki; Tsujine, Yukari; Fukao, Tomoko; Nakano, Masayoshi; Matsuzaki, Akiyoshi; Sato, Hiroyasu

2002-01-01

Films are deposited on substrates at 20 deg.C by excimer laser ablation (ELA) of mixture targets of 3,4,9,10-perylenetetracarboxylic dianhydride (PTCDA) with metal powder, PTCDA/M (M=Co, Ni, Fe, W, Cu and Ag) using XeCl and ArF beams. Large amount of fragments with ''naked'' perylene skeletons can be produced owing to effective elimination of carboxylic dianhydride groups by ELA of PTCDA/Co both with XeCl and ArF beams under optimized ablation conditions. Elimination reaction of side groups of PTCDA is observed for ELA of the targets with metal powder of the iron group, Co, Fe and Ni, especially remarkable for Co and Fe. The film from PTCDA/Ni consists of small particles with the various diameters ranging from 10 to 100 nm as well as that from PTCDA/Co. Morphology like petal of rose can be seen everywhere for the film from PTCDA/Fe

Photopatternable Magnetic Hollowbots by Nd-Fe-B Nanocomposite for Potential Targeted Drug Delivery Applications

Directory of Open Access Journals (Sweden)

Hui Li

2018-04-01

Full Text Available In contrast to traditional drug administration, targeted drug delivery can prolong, localize, target and have a protected drug interaction with the diseased tissue. Drug delivery carriers, such as polymeric micelles, liposomes, dendrimers, nanotubes, and so on, are hard to scale-up, costly, and have short shelf life. Here we show the novel fabrication and characterization of photopatternable magnetic hollow microrobots that can potentially be utilized in microfluidics and drug delivery applications. These magnetic hollowbots can be fabricated using standard ultraviolet (UV lithography with low cost and easily accessible equipment, which results in them being easy to scale up, and inexpensive to fabricate. Contact-free actuation of freestanding magnetic hollowbots were demonstrated by using an applied 900 G external magnetic field to achieve the movement control in an aqueous environment. According to the movement clip, the average speed of the magnetic hollowbots was estimated to be 1.9 mm/s.

Composite Flowable Fabricated (CFF Sebagai Alternatif Bahan Pasak Gigi Paska Endodontik

Directory of Open Access Journals (Sweden)

Dwi Warna Aju Fatmawati

2014-12-01

for 20 seconds. Treatment of NiTi post group was same with CCF post group, the different NiTi post was inserted using glass ionomer luting type 1. Furthermore all of tooth sample, prefabricated and fabricated, was tested by threebending point with ISO10477. The result showed that mean of NiTi post (stiffness= 115,30 N/mm; modulus elastisitas = 9,31 Gpa; flexural= 812 Gpa was higher than CFF post (stiffness = 35 N/mm; modulus elastisitas = 3,45 Gpa; flexural= 475,8 GPa; and there was significant different between prefabricated (NiTi dengan fabricated(CFF post statistically. Although composite flowable can be used as alternative of post endodontic and needs further research that is suitable with standard of post materials.

Synthesis of nanosilver on polyamide fabric using silver/ammonia complex

Energy Technology Data Exchange (ETDEWEB)

Montazer, Majid, E-mail: tex5mm@aut.ac.ir [Textile Department, Functional Fibrous Structures and Environmental Enhancement (FFSEE), Amirkabir University of Technology, Hafez Avenue, Tehran (Iran, Islamic Republic of); Shamei, Ali; Alimohammadi, Farbod [Young Researchers Club, Tehran South Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of)

2014-05-01

In this paper, a novel synthesis method for nanosilver has been introduced on or within the polymeric chains of polyamide 6 fabric by using silver/ammonia complex [Ag(NH{sub 3}){sub 2}]{sup +}. The silver complex was reduced directly by functional groups of polyamide chains without using any additional chemical reducing agents. The polyamide fabric was also stabilized with formation of new linkages between the polymeric chains of the nylon fabric through silver nanoparticle synthesis. The presence of nanosilver on the fabric was confirmed by UV–vis spectra, EDX patterns and XRD patterns. In addition, X-ray photoelectron spectroscopy (XPS) was utilized to identify the chemical state of silver in a range of silver oxide and silver metal. The SEM images confirmed the presence of nanosilver on the polyamide within the size of 20 and 150 nm. Excellent antibacterial properties were achieved with the treated fabrics against Staphylococcus aureus and Escherichia coli. Further, the antibacterial properties of the polyamide fabric treated with 35 mg/L silver/ammonia were durable against washing as they only decreased to 98.6% after 20 washes. In addition, some other properties of the treated fabrics including color changes, dimensional stability, water droplet adsorption, and reflectance spectrum are reported and thoroughly discussed. - Highlights: • Novel in situ synthesis of nanosilver on polyamide 6 • Synthesis of nanosilver without using external stabilizing and reducing agent • Synthesis of nanosilver particles within molecular chains of polyamide 6 • Producing antibacterial polyamide 6 using 35 mg/L Ag/ammonia complex • Obtaining durable antibacterial properties on polyamide 6 by this method.

Synthesis of nanosilver on polyamide fabric using silver/ammonia complex

International Nuclear Information System (INIS)

Montazer, Majid; Shamei, Ali; Alimohammadi, Farbod

2014-01-01

In this paper, a novel synthesis method for nanosilver has been introduced on or within the polymeric chains of polyamide 6 fabric by using silver/ammonia complex [Ag(NH 3 ) 2 ] + . The silver complex was reduced directly by functional groups of polyamide chains without using any additional chemical reducing agents. The polyamide fabric was also stabilized with formation of new linkages between the polymeric chains of the nylon fabric through silver nanoparticle synthesis. The presence of nanosilver on the fabric was confirmed by UV–vis spectra, EDX patterns and XRD patterns. In addition, X-ray photoelectron spectroscopy (XPS) was utilized to identify the chemical state of silver in a range of silver oxide and silver metal. The SEM images confirmed the presence of nanosilver on the polyamide within the size of 20 and 150 nm. Excellent antibacterial properties were achieved with the treated fabrics against Staphylococcus aureus and Escherichia coli. Further, the antibacterial properties of the polyamide fabric treated with 35 mg/L silver/ammonia were durable against washing as they only decreased to 98.6% after 20 washes. In addition, some other properties of the treated fabrics including color changes, dimensional stability, water droplet adsorption, and reflectance spectrum are reported and thoroughly discussed. - Highlights: • Novel in situ synthesis of nanosilver on polyamide 6 • Synthesis of nanosilver without using external stabilizing and reducing agent • Synthesis of nanosilver particles within molecular chains of polyamide 6 • Producing antibacterial polyamide 6 using 35 mg/L Ag/ammonia complex • Obtaining durable antibacterial properties on polyamide 6 by this method

Prospective Randomized Double-Blind Pilot Study of Site-Specific Consensus Atlas Implementation for Rectal Cancer Target Volume Delineation in the Cooperative Group Setting

International Nuclear Information System (INIS)

Fuller, Clifton D.; Nijkamp, Jasper; Duppen, Joop C.; Rasch, Coen R.N.; Thomas, Charles R.; Wang, Samuel J.; Okunieff, Paul; Jones, William E.; Baseman, Daniel; Patel, Shilpen; Demandante, Carlo G.N.; Harris, Anna M.; Smith, Benjamin D.; Katz, Alan W.; McGann, Camille

2011-01-01

Purpose: Variations in target volume delineation represent a significant hurdle in clinical trials involving conformal radiotherapy. We sought to determine the effect of a consensus guideline-based visual atlas on contouring the target volumes. Methods and Materials: A representative case was contoured (Scan 1) by 14 physician observers and a reference expert with and without target volume delineation instructions derived from a proposed rectal cancer clinical trial involving conformal radiotherapy. The gross tumor volume (GTV), and two clinical target volumes (CTVA, including the internal iliac, presacral, and perirectal nodes, and CTVB, which included the external iliac nodes) were contoured. The observers were randomly assigned to receipt (Group A) or nonreceipt (Group B) of a consensus guideline and atlas for anorectal cancers and then instructed to recontour the same case/images (Scan 2). Observer variation was analyzed volumetrically using the conformation number (CN, where CN = 1 equals total agreement). Results: Of 14 evaluable contour sets (1 expert and 7 Group A and 6 Group B observers), greater agreement was found for the GTV (mean CN, 0.75) than for the CTVs (mean CN, 0.46-0.65). Atlas exposure for Group A led to significantly increased interobserver agreement for CTVA (mean initial CN, 0.68, after atlas use, 0.76; p = .03) and increased agreement with the expert reference (initial mean CN, 0.58; after atlas use, 0.69; p = .02). For the GTV and CTVB, neither the interobserver nor the expert agreement was altered after atlas exposure. Conclusion: Consensus guideline atlas implementation resulted in a detectable difference in interobserver agreement and a greater approximation of expert volumes for the CTVA but not for the GTV or CTVB in the specified case. Visual atlas inclusion should be considered as a feature in future clinical trials incorporating conformal RT.

Prospective randomized double-blind pilot study of site-specific consensus atlas implementation for rectal cancer target volume delineation in the cooperative group setting

Science.gov (United States)

Fuller, Clifton D.; Nijkamp, Jasper; Duppen, Joop; Rasch, Coen R.N.; Thomas, Charles R.; Wang, Samuel J.; Okunieff, Paul; Jones, William E.; Baseman, Daniel; Patel, Shilpen; Demandante, Carlo G. N.; Harris, Anna M.; Smith, Benjamin D.; Katz, Alan W.; McGann, Camille; Harper, Jennifer L.; Chang, Daniel T.; Smalley, Stephen; Marshall, David T.; Goodman, Karyn A.; Papanikolaou, Niko; Kachnic, Lisa A.

2010-01-01

Purpose Variation in target volume delineation represents a significant hurdle in clinical trials involving conformal radiotherapy. We sought to determine the impact of a consensus guideline-based visual atlas on contouring of target volumes. Methods A representative case and target volume delineation instructions derived from a proposed rectal cancer clinical trial involving conformal radiotherapy were contoured (Scan1) by 14 physician observers and a reference expert. Gross tumor volume (GTV), and 2 clinical target volumes (CTVA, comprising internal iliac, pre-sacral, and peri-rectal nodes, and CTVB, external iliac nodes) were contoured. Observers were randomly assigned to receipt (Group_A) /non-receipt (Group_B) of a consensus guideline and atlas for anorectal cancers, then instructed to re-contour the same case/images (Scan2). Observer variation was analyzed volumetrically using conformation number (CN, where CN=1 equals a total agreement). Results In 14 evaluable contour sets (1 expert, 7 Group_A, 6 Group_B), there was greater agreement for GTV (mean CN 0.75) than CTVs (mean CN 0.46–0.65). Atlas exposure for Group_A led to a significant increased inter-observer agreement for CTVA (mean initial CN 0.68, post-atlas 0.76; p=0.03), as well as increased agreement with the expert reference (initial mean CN 0.58, 0.69 post-atlas; p=0.02). For GTV and CTVB, neither inter-observer nor expert agreement was altered after atlas exposure. Conclusion Consensus guideline atlas implementation resulted in a detectable difference in inter-observer agreement and greater approximation of expert volumes for CTVA, but not GTV or CTVB, in the specified case. Visual atlas inclusion should be considered as a feature in future clinical trials incorporating conformal radiotherapy. PMID:20400244

Drip bloodstain appearance on inclined apparel fabrics: Effect of prior-laundering, fibre content and fabric structure.

Science.gov (United States)

de Castro, Therese C; Carr, Debra J; Taylor, Michael C; Kieser, Jules A; Duncan, Warwick

2016-09-01

The interaction of blood and fabrics is currently a 'hot topic', since the understanding and interpretation of these stains is still in its infancy. A recent simplified perpendicular impact experimental programme considering bloodstains generated on fabrics laid the foundations for understanding more complex scenarios. Blood rarely impacts apparel fabrics perpendicular; therefore a systematic study was conducted to characterise the appearance of drip stains on inclined fabrics. The final drip stain appearance for 45° and 15° impact angles on torso apparel fabrics (100% cotton plain woven, 100% polyester plain woven, a blend of polyester and cotton plain woven and 100% cotton single jersey knit) that had been laundered for six, 26 and 52 cycles prior to testing was investigated. The relationship between drop parameters (height and volume), angle and the stain characteristics (parent stain area, axis 1 and 2 and number of satellite stains) for each fabric was examined using analysis of variance. The appearance of the drip stains on these fabrics was distorted, in comparison to drip stains on hard-smooth surface. Examining the parent stain allowed for classification of stains occurring at an angle, however the same could not be said for the satellite stains produced. All of the dried stains visible on the surface of the fabric were larger than just after the impacting event, indicating within fabric spreading of blood due to capillary force (wicking). The cotton-containing fabrics spread the blood within the fabrics in all directions along the stain's circumference, while spreading within the polyester plain woven fabric occurred in only the weft (width of the fabric) and warp (length) directions. Laundering affected the formation of bloodstain on the blend plain woven fabric at both impact angles, although not all characteristics were significantly affected for the three impact conditions considered. The bloodstain characteristics varied due to the fibre content

Laval nozzles for cluster-jet targets

Energy Technology Data Exchange (ETDEWEB)

Grieser, Silke; Bonaventura, Daniel; Hergemoeller, Ann-Katrin; Hetz, Benjamin; Koehler, Esperanza; Lessmann, Lukas; Khoukaz, Alfons [Institut fuer Kernphysik, Westfaelische Wilhelms-Universitaet Muenster, 48149 Muenster (Germany)

2016-07-01

Cluster-jet targets are highly suited for storage ring experiments due to the fact that they provide high and constant beam densities. Therefore, a cluster-jet target is planned to be the first internal target for the PANDA experiment at FAIR. A cluster source generates a continuous flow of cryogenic solid clusters by the expansion of pre-cooled gases within fine Laval nozzles. For the production of clusters the geometry of the nozzle is crucial. The production of such nozzles with their complex inner geometry represents a major technical challenge. The possibility to produce new fine Laval nozzles ensures the operation of cluster-jet targets, e.g. for the PANDA experiment, and opens the way for future investigations on the cluster production process to match the required targets performance. Optimizations on the recently developed production process and the fabrication of new glass nozzles were done. Initial measurements of these nozzles at the PANDA cluster-jet target prototype and the investigation of the cluster beam origin within the nozzle will be presented and discussed. For the future more Laval nozzles with different geometries will be produced and additional measurements with these new nozzles at the PANDA cluster-jet target prototype towards higher performance will be realized.

Influence of Fabric Parameters on Thermal Comfort Performance of Double Layer Knitted Interlock Fabrics

Directory of Open Access Journals (Sweden)

Afzal Ali

2017-03-01

Full Text Available The aim of this study was to analyse the effects of various fabric parameters on the thermal resistance, thermal conductivity, thermal transmittance, thermal absorptivity and thermal insulation of polyester/cotton double layer knitted interlock fabrics. It was found that by increasing fibre content with higher specific heat increases the thermal insulation while decreases the thermal transmittance and absorptivity of the fabric. It was concluded that double layer knitted fabrics developed with higher specific heat fibres, coarser yarn linear densities, higher knitting loop length and fabric thickness could be adequately used for winter clothing purposes.

1024x1024 resistive emitter array design and fabrication status

Science.gov (United States)

Bryant, Paul T.; Oleson, Jim; McHugh, Stephen W.; Beuville, Eric; Schlesselmann, John D.; Woolaway, James T.; Barskey, Steve; Solomon, Steven L.; Joyner, Thomas W.

2002-07-01

Santa Barbara Infrared (SBIR) is producing a high performance 1,024 x 1,024 Large Format Resistive emitter Array (LFRA) for use in the next generation of IR Scene Projectors (IRSPs). LFRA requirements were developed through close cooperation with the Tri-Service IR Scene Projector working group, and through detailed trade studies sponsored by the OSD Central T&E Investment Program (CTEIP) and a Phase I US Navy Small Business Innovative Research (SBIR) contract. The CMOS Read-In Integrated Circuit (RIIC) is being designed by SBIR and Indigo Systems under a Small Business Innovative Research (SBIR) contract. Performance and features include 750 K MWIR maximum apparent temperature, 5 ms radiance rise time, 200 Hz full frame update, and 400 Hz window mode operation. Ten 8-inch CMOS wafers will be fabricated and characterized in mid-2002, followed by emitter fabrication in late 2002. This paper discusses array performance, requirements flow-down, array design, fabrication of 2 X 2-inch CMOS devices, and plans for subsequent RIIC wafer test and emitter pixel fabrication.

A facile method to fabricate superhydrophobic cotton fabrics

Science.gov (United States)

Zhang, Ming; Wang, Shuliang; Wang, Chengyu; Li, Jian

2012-11-01

A facile and novel method for fabricating superhydrophobic cotton fabrics is described in the present work. The superhydrophobic surface has been prepared by utilizing cationic poly (dimethyldiallylammonium chloride) and silica particles together with subsequent modification of (heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane. The size distribution of silica particles was measured by Particle Size Analyzer. The cotton textiles before and after treatment were characterized by using scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). The wetting behavior of cotton samples was investigated by water contact angle measurement. Moreover, the superhydrophobic durability of coated cotton textiles has been evaluated by exposure, immersion and washing tests. The results show that the treated cotton fabrics exhibited excellent chemical stability and outstanding non-wettability with the WCA of 155 ± 2°, which offers an opportunity to accelerate the large-scale production of superhydrophobic textiles materials for new industrial applications.

Cryogenic hydrogen fuel for controlled inertial confinement fusion (formation of reactor-scale cryogenic targets)

Energy Technology Data Exchange (ETDEWEB)

Aleksandrova, I. V.; Koresheva, E. R., E-mail: elena.koresheva@gmail.com; Krokhin, O. N. [Russian Academy of Sciences, Lebedev Physical Institute (Russian Federation); Osipov, I. E. [Power Efficiency Centre, Inter RAO UES (Russian Federation)

2016-12-15

In inertial fusion energy research, considerable attention has recently been focused on low-cost fabrication of a large number of targets by developing a specialized layering module of repeatable operation. The targets must be free-standing, or unmounted. Therefore, the development of a target factory for inertial confinement fusion (ICF) is based on methods that can ensure a cost-effective target production with high repeatability. Minimization of the amount of tritium (i.e., minimization of time and space at all production stages) is a necessary condition as well. Additionally, the cryogenic hydrogen fuel inside the targets must have a structure (ultrafine layers—the grain size should be scaled back to the nanometer range) that supports the fuel layer survivability under target injection and transport through the reactor chamber. To meet the above requirements, significant progress has been made at the Lebedev Physical Institute (LPI) in the technology developed on the basis of rapid fuel layering inside moving free-standing targets (FST), also referred to as the FST layering method. Owing to the research carried out at LPI, unique experience has been gained in the development of the FST-layering module for target fabrication with an ultrafine fuel layer, including a reactor- scale target design. This experience can be used for the development of the next-generation FST-layering module for construction of a prototype of a target factory for power laser facilities and inertial fusion power plants.

Cigarette advertising in Mumbai, India: targeting different socioeconomic groups, women, and youth.

Science.gov (United States)

Bansal, R; John, S; Ling, P M

2005-06-01

Despite a recent surge in tobacco advertising and the recent advertising ban (pending enforcement at the time of this study), there are few studies describing current cigarette marketing in India. This study sought to assess cigarette companies' marketing strategies in Mumbai, India. A two week field study was conducted in Mumbai in September 2003, observing, documenting, and collecting cigarette advertising on billboards, storefronts and at point of sale along two major thoroughfares, and performing a content analysis of news, film industry, and women's magazines and three newspapers. Cigarette advertising was ubiquitous in the environment, present in news and in film magazines, but not in women's magazines or the newspapers. The four major advertising campaigns all associated smoking with aspiration; the premium brands targeting the higher socioeconomic status market utilised tangible images of westernization and affluence whereas the "bingo" (low priced) segment advertisements invited smokers to belong to a league of their own and "rise to the taste" using intangible images. Women were not depicted smoking, but were present in cigarette advertisements--for example, a woman almost always accompanied a man in "the man with the smooth edge" Four Square campaign. Advertisements and product placements at low heights and next to candies at point of sale were easily accessible by children. In view of the imminent enforcement of the ban on tobacco advertisements, cigarette companies are increasing advertising for the existing brand images, launching brand extensions, and brand stretching. Cigarette companies have developed sophisticated campaigns targeting men, women, and children in different socioeconomic groups. Many of these strategies circumvent the Indian tobacco advertising ban. Understanding these marketing strategies is critical to minimise the exploitation of loopholes in tobacco control legislation.

Fabrication of an Open Microfluidic Device for Immunoblotting.

Science.gov (United States)

Abdel-Sayed, Philippe; Yamauchi, Kevin A; Gerver, Rachel E; Herr, Amy E

2017-09-19

Given the wide adoption of polydimethylsiloxane (PDMS) for the rapid fabrication of microfluidic networks and the utility of polyacrylamide gel electrophoresis (PAGE), we develop a technique for fabrication of PAGE molecular sieving gels in PDMS microchannel networks. In developing the fabrication protocol, we trade-off constraints on materials properties of these two polymer materials: PDMS is permeable to O 2 and the presence of O 2 inhibits the polymerization of polyacrylamide. We present a fabrication method compatible with performing PAGE protein separations in a composite PDMS-glass microdevice, that toggles from an "enclosed" microchannel for PAGE and blotting to an "open" PA gel lane for immunoprobing and readout. To overcome the inhibitory effects of O 2 , we coat the PDMS channel with a 10% benzophenone solution, which quenches the inhibiting effect of O 2 when exposed to UV, resulting in a PAGE-in-PDMS device. We then characterize the PAGE separation performance. Using a ladder of small-to-mid mass proteins (Trypsin Inhibitor (TI); Ovalbumin (OVA); Bovine Serum Albumin (BSA)), we observe resolution of the markers in TI, with comparable reproducibility to glass microdevice PAGE. We show that benzophenone groups incorporated into the gel through methacrylamide can be UV-activated multiple times to photocapture protein. PDMS microchannel network is reversibly bonded to a glass slide allowing direct access to separated proteins and subsequent in situ diffusion-driven immunoprobing and total protein Sypro red staining. We see this PAGE-in-PDMS fabrication technique as expanding the application and use of microfluidic PAGE without the need for a glass microfabrication infrastructure.

Fabrication of three-dimensional scaffolds using precision extrusion deposition with an assisted cooling device

Energy Technology Data Exchange (ETDEWEB)

Hamid, Q; Snyder, J; Wang, C; Guceri, S; Sun, W [Department of Mechanical Engineering and Mechanics, Drexel University, Philadelphia, PA (United States); Timmer, M; Hammer, J, E-mail: sunwei@drexel.edu [Advanced Technologies and Regenerative Medicine, Somerville, NJ (United States)

2011-09-15

In the field of biofabrication, tissue engineering and regenerative medicine, there are many methodologies to fabricate a building block (scaffold) which is unique to the target tissue or organ that facilitates cell growth, attachment, proliferation and/or differentiation. Currently, there are many techniques that fabricate three-dimensional scaffolds; however, there are advantages, limitations and specific tissue focuses of each fabrication technique. The focus of this initiative is to utilize an existing technique and expand the library of biomaterials which can be utilized to fabricate three-dimensional scaffolds rather than focusing on a new fabrication technique. An expanded library of biomaterials will enable the precision extrusion deposition (PED) device to construct three-dimensional scaffolds with enhanced biological, chemical and mechanical cues that will benefit tissue generation. Computer-aided motion and extrusion drive the PED to precisely fabricate micro-scaled scaffolds with biologically inspired, porosity, interconnectivity and internal and external architectures. The high printing resolution, precision and controllability of the PED allow for closer mimicry of tissues and organs. The PED expands its library of biopolymers by introducing an assisting cooling (AC) device which increases the working extrusion temperature from 120 to 250 deg. C. This paper investigates the PED with the integrated AC's capabilities to fabricate three-dimensional scaffolds that support cell growth, attachment and proliferation. Studies carried out in this paper utilized a biopolymer whose melting point is established to be 200 deg. C. This polymer was selected to illustrate the newly developed device's ability to fabricate three-dimensional scaffolds from a new library of biopolymers. Three-dimensional scaffolds fabricated with the integrated AC device should illustrate structural integrity and ability to support cell attachment and proliferation.

3D Bioprinting for Tissue and Organ Fabrication.

Science.gov (United States)

Zhang, Yu Shrike; Yue, Kan; Aleman, Julio; Moghaddam, Kamyar Mollazadeh; Bakht, Syeda Mahwish; Yang, Jingzhou; Jia, Weitao; Dell'Erba, Valeria; Assawes, Pribpandao; Shin, Su Ryon; Dokmeci, Mehmet Remzi; Oklu, Rahmi; Khademhosseini, Ali

2017-01-01

The field of regenerative medicine has progressed tremendously over the past few decades in its ability to fabricate functional tissue substitutes. Conventional approaches based on scaffolding and microengineering are limited in their capacity of producing tissue constructs with precise biomimetic properties. Three-dimensional (3D) bioprinting technology, on the other hand, promises to bridge the divergence between artificially engineered tissue constructs and native tissues. In a sense, 3D bioprinting offers unprecedented versatility to co-deliver cells and biomaterials with precise control over their compositions, spatial distributions, and architectural accuracy, therefore achieving detailed or even personalized recapitulation of the fine shape, structure, and architecture of target tissues and organs. Here we briefly describe recent progresses of 3D bioprinting technology and associated bioinks suitable for the printing process. We then focus on the applications of this technology in fabrication of biomimetic constructs of several representative tissues and organs, including blood vessel, heart, liver, and cartilage. We finally conclude with future challenges in 3D bioprinting as well as potential solutions for further development.

3D Bioprinting for Tissue and Organ Fabrication

Science.gov (United States)

Zhang, Yu Shrike; Yang, Jingzhou; Jia, Weitao; Dell’Erba, Valeria; Assawes, Pribpandao; Shin, Su Ryon; Dokmeci, Mehmet Remzi; Oklu, Rahmi; Khademhosseini, Ali

2016-01-01

The field of regenerative medicine has progressed tremendously over the past few decades in its ability to fabricate functional tissue substitutes. Conventional approaches based on scaffolding and microengineering are limited in their capacity of producing tissue constructs with precise biomimetic properties. Three-dimensional (3D) bioprinting technology, on the other hand, promises to bridge the divergence between artificially engineered tissue constructs and native tissues. In a sense, 3D bioprinting offers unprecedented versatility to co-deliver cells and biomaterials with precise control over their compositions, spatial distributions, and architectural accuracy, therefore achieving detailed or even personalized recapitulation of the fine shape, structure, and architecture of target tissues and organs. Here we briefly describe recent progresses of 3D bioprinting technology and associated bioinks suitable for the printing process. We then focus on the applications of this technology in fabrication of biomimetic constructs of several representative tissues and organs, including blood vessel, heart, liver, and cartilage. We finally conclude with future challenges in 3D bioprinting as well as potential solutions for further development. PMID:27126775

Recent advances in indirect drive ICF target physics at LLNL

International Nuclear Information System (INIS)

Hammel, B.A.; Bernat, T.P.; Collins, G.W.; Haan, S.; Landen, O.L.; MacGowan, B.J.; Suter, L.J.

1999-01-01

In preparation for ignition on the National Ignition Facility, the Lawrence Livermore National Laboratory's Inertial Confinement Fusion Program, working in collaboration with Los Alamos National Laboratory, Commissariat a l'Energie Atomique (CEA), and Laboratory for Laser Energetics at the University of Rochester, has performed a broad range of experiments on the Nova and Omega lasers to test the fundamentals of the NIF target designs. These studies have refined our understanding of the important target physics, and have led to many of the specifications for the NIF laser and the cryogenic ignition targets. Our recent work has been focused in the areas of hohlraum energetics, symmetry, shock physics, and target design optimization and fabrication. (author)

Fabric Reconstruction Based on Sustainable Development: Take the Type of Fabric Recycling as an Example

OpenAIRE

Zhangting Guan

2017-01-01

Sustainable development is a very important concept of our time, it wants to do is to live in harmony with people, to protect the environment where our human survival. Fabric recycling refers to the use of a variety of traditional and high-tech means of the existing fabric fabric design and processing. So that the surface of a rich visual texture and tactile texture "through the fabric recycling approach. However, the fabric form and clothing design coordination between the clothing design is...

International target values 2000 for measurement uncertainties in safeguarding nuclear materials

International Nuclear Information System (INIS)

Aigner, H.; Binner, R.; Kuhn, E.

2001-01-01

The IAEA has prepared a revised and updated version of International Target Values (ITVs) for uncertainty components in measurements of nuclear material. The ITVs represent uncertainties to be considered in judging the reliability of analytical techniques applied to industrial nuclear and fissile material subject to safeguards verification. The tabulated values represent estimates of the 'state of the practice' which ought to be achievable under routine conditions by adequately equipped, experienced laboratories. The ITVs 2000 are intended to be used by plant operators and safeguards organizations as a reference of the quality of measurements achievable in nuclear material accountancy, and for planning purposes. The IAEA prepared a draft of a technical report presenting the proposed ITVs 2000, and in April 2000 the chairmen or officers of the panels or organizations listed below were invited to co- author the report and to submit the draft to a discussion by their panels and organizations. Euratom Safeguards Inspectorate, ESAKDA Working Group on Destructive Analysis, ESARDA Working Group on Non Destructive Analysis, Institute of Nuclear Material Management, Japanese Expert Group on ITV-2000, ISO Working Group on Analyses in Spent Fuel Reprocessing, ISO Working Group on Analyses in Uranium Fuel Fabrication, ISO Working Group on Analyses in MOX Fuel Fabrication, Agencia Brasileno-Argentina de Contabilidad y Control de Materiales Nucleares (ABACC). Comments from the above groups were received and incorporated into the final version of the document, completed in April 2001. The ITVs 2000 represent target standard uncertainties, expressing the precision achievable under stipulated conditions. These conditions typically fall in one of the two following categories: 'repeatability conditions' normally encountered during the measurements done within one inspection period; or 'reproducibility conditions' involving additional sources of measurement variability such as

Erratum to ‘Identifying policy target groups with qualitative and quantitative methods: the case of wildfire risk on nonindustrial private forest lands’ [Forest Policy and Economics. 25: 62–71

Science.gov (United States)

A. Paige Fischer; Jeffrey D. Kline; Susan Charnley; Christine. Olsen

2013-01-01

Designing policies to harness the potential of heterogeneous target groups such as nonindustrial private forest owners to contribute to public policy goals can be challenging. The behaviors of such groups are shaped by their diverse motivations and circumstances. Segmenting heterogeneous target groups into more homogeneous subgroups may improve the chances of...

Fabrication of superhydrophobic niobium pentoxide thin films by anodization

Energy Technology Data Exchange (ETDEWEB)

Jeong, Bong-Yong [Future Convergence Ceramic Division, Korea Institute of Ceramic Engineering and Technology, Seoul 153-801 (Korea, Republic of); Jung, Eun-Hye [Future Convergence Ceramic Division, Korea Institute of Ceramic Engineering and Technology, Seoul 153-801 (Korea, Republic of); Department of Chemical Engineering, Inha University, Incheon 402-024 (Korea, Republic of); Kim, Jin-Ho, E-mail: jhkim@kicet.re.kr [Electronic and Optic Materials Division, Korea Institute of Ceramic Engineering and Technology, Seoul 153-801 (Korea, Republic of)

2014-07-01

We report a simple method to fabricate a niobium oxide film with a lotus-like micro–nano surface structure. Self-assembled niobium pentoxide (Nb{sub 2}O{sub 5}) films with superhydrophobic property were fabricated by an anodization and a hydrophobic treatment. This process has several advantages such as low cost, simplicity and easy coverage of a large area. The surface of fabricated Nb{sub 2}O{sub 5} film was changed from hydrophilic to superhydrophobic surface by a treatment using fluoroaldyltrimethoxysilane (FAS) solution. This value is considered to be the lowest surface free energy of any solid, based on the alignment of -CF{sub 3} groups on the surface. In particular, among FAS coated surfaces, the micro–nano complex cone structured Nb{sub 2}O{sub 5} film showed the highest water-repellent property with a static contact angle of ca. 162°. This study gives promising routes from biomimetic superhydrophobic surfaces.

Metallic Reactor Fuel Fabrication for SFR

Energy Technology Data Exchange (ETDEWEB)

Song, Hoon; Kim, Jong-Hwan; Ko, Young-Mo; Woo, Yoon-Myung; Kim, Ki-Hwan; Lee, Chan-Bock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

The metal fuel for an SFR has such advantages such as simple fabrication procedures, good neutron economy, high thermal conductivity, excellent compatibility with a Na coolant, and inherent passive safety 1. U-Zr metal fuel for SFR is now being developed by KAERI as a national R and D program of Korea. The fabrication technology of metal fuel for SFR has been under development in Korea as a national nuclear R and D program since 2007. The fabrication process for SFR fuel is composed of (1) fuel slug casting, (2) loading and fabrication of the fuel rods, and (3) fabrication of the final fuel assemblies. Fuel slug casting is the dominant source of fuel losses and recycled streams in this fabrication process. Fabrication on the rod type metallic fuel was carried out for the purpose of establishing a practical fabrication method. Rod-type fuel slugs were fabricated by injection casting. Metallic fuel slugs fabricated showed a general appearance was smooth.

One-pot fabrication and antimicrobial properties of novel PET nonwoven fabrics

International Nuclear Information System (INIS)

Lin Song; Wang Zheng; Qi Jiancheng; Wu Jinhui; Tian Tao; Hao Limei; Yang Jingquan; Hou Lili

2011-01-01

Recently, with the ever-growing demand for healthy living, more and more research is focused on materials capable of killing harmful microorganisms around the world. It is believed that designing such protective materials for hygienic and biomedical applications can benefit people in professional areas and daily life. Thus, in this paper, one novel kind of antibacterial poly(ethylene terephthalate) (PET) nonwoven fabrics was conveniently one-pot prepared, with the combined immobilization of two biological antimicrobial agents, i.e. ε-polylysine and natamycin, by using the soft methacrylate nonwoven fabrics adhesives. Then, the antimicrobial activities of the functional fabrics were investigated by using the standard shaking-flask method, showing excellent antibacterial efficiency (AE) against both Escherichia coli (8099) and Staphylococcus aureus (ATCC 6538) (AE > 99.99%) compared with untreated PET nonwoven fabrics. The anti-bioaerosol tests also showed similar trends. Meantime, scanning electron microscopy analysis indicated that the bacteria on the antibacterial PET appeared to be partly bacteriolyzed and showed much less viability than those on the pristine ones. Moreover, the long residual biocidal action of such modified PET fabrics was also evaluated, and the antibacterial activity of antibacterial fibers was unaffected by the 3 month artificially accelerated aging.

One-pot fabrication and antimicrobial properties of novel PET nonwoven fabrics

Energy Technology Data Exchange (ETDEWEB)

Lin Song; Wang Zheng; Qi Jiancheng; Wu Jinhui; Tian Tao; Hao Limei; Yang Jingquan [Institute of Medical Equipment, Academy of Military Medical Sciences, Tianjin 300161 (China); Hou Lili, E-mail: yjq789@sohu.com [National Bio-protection Engineering Center, Tianjin 300161 (China)

2011-08-15

Recently, with the ever-growing demand for healthy living, more and more research is focused on materials capable of killing harmful microorganisms around the world. It is believed that designing such protective materials for hygienic and biomedical applications can benefit people in professional areas and daily life. Thus, in this paper, one novel kind of antibacterial poly(ethylene terephthalate) (PET) nonwoven fabrics was conveniently one-pot prepared, with the combined immobilization of two biological antimicrobial agents, i.e. {epsilon}-polylysine and natamycin, by using the soft methacrylate nonwoven fabrics adhesives. Then, the antimicrobial activities of the functional fabrics were investigated by using the standard shaking-flask method, showing excellent antibacterial efficiency (AE) against both Escherichia coli (8099) and Staphylococcus aureus (ATCC 6538) (AE > 99.99%) compared with untreated PET nonwoven fabrics. The anti-bioaerosol tests also showed similar trends. Meantime, scanning electron microscopy analysis indicated that the bacteria on the antibacterial PET appeared to be partly bacteriolyzed and showed much less viability than those on the pristine ones. Moreover, the long residual biocidal action of such modified PET fabrics was also evaluated, and the antibacterial activity of antibacterial fibers was unaffected by the 3 month artificially accelerated aging.

Fabrication of integrated metallic MEMS devices

DEFF Research Database (Denmark)

Yalcinkaya, Arda Deniz; Ravnkilde, Jan Tue; Hansen, Ole

2002-01-01

A simple and complementary metal oxide semiconductor (CMOS) compatible fabrication technique for microelectromechanical (MEMS) devices is presented. The fabrication technology makes use of electroplated metal layers. Among the fabricated devices, high quality factor microresonators are characteri......A simple and complementary metal oxide semiconductor (CMOS) compatible fabrication technique for microelectromechanical (MEMS) devices is presented. The fabrication technology makes use of electroplated metal layers. Among the fabricated devices, high quality factor microresonators...

Optics fabrication technical challenges

International Nuclear Information System (INIS)

Chabassier, G.; Ferriou, N.; Lavastre, E.; Maunier, C.; Neauport, J.; Taroux, D.; Balla, D.; Fornerod, J.C.

2004-01-01

Before the production of all the LMJ (MEGAJOULE laser) optics, the CEA had to proceed with the fabrication of about 300 large optics for the LIL (laser integration line) laser. Thanks to a fruitful collaboration with high-tech optics companies in Europe, this challenge has been successfully hit. In order to achieve the very tight requirements for cleanliness, laser damage threshold and all the other high demanding fabrication specifications, it has been necessary to develop and to set completely new fabrication process going and to build special outsize fabrication equipment. Through a couple of examples, this paper gives an overview of the work which has been done and shows some of the results which have been obtained: continuous laser glass melting, fabrication of the laser slabs, rapid-growth KDP (potassium dihydrogen phosphate) technology, large diffractive transmission gratings engraving and characterization. (authors)

Design of ignition targets for the National Ignition Facility

International Nuclear Information System (INIS)

Haan, S.W.; Dittrich, T.R.; Marinak, M.M.; Hinkel, D.E.

1999-01-01

This is a brief update on the work being done to design ignition targets for the National Ignition Facility. Updates are presented on three areas of current activity : improvements in modeling, work on a variety of targets spanning the parameter space of possible ignition targets ; and the setting of specifications for target fabrication and diagnostics. Highlights of recent activity include : a simulation of the Rayleigh-Taylor instability growth on an imploding capsule, done in 3D on a 72degree by 72degree wedge, with enough zones to resolve modes out to 100 ; and designs of targets at 250eV and 350eV, as well as the baseline 300 eV ; and variation of the central DT gas density, which influences both the Rayleigh-Taylor growth and the smoothness of the DT ice layer

[Personnel marketing in anesthesiology. Perception, use and evaluation by the target group].

Science.gov (United States)

Berlet, T

2015-09-01

department's range of activities. The correlation between familiarity with PM tools and positive benefit assessments was low. The results of this PM study can contribute to the development of an effective and efficient conception of PM measures by hospitals. Addressing applicants through traditional job and internet-based advertisements should be supplemented by personalized targeting of potential applicants and innovative targeting instruments must be systematically developed and promoted in order to become effective. It remains questionable whether the target group of external PM can be reached with exclusively or even predominantly image-cultivating measures on behalf of the healthcare company, such as image campaigns. The most effective PM tools create good working conditions and develop factors contributing to the employer's attractiveness. These two tools should be given priority in human resource development also taking material incentives into consideration, all of which support the effective set-up of an employer branding.

[Osteogenic activity of porous calcium phosphate ceramics fabricated by rapid prototyping].

Science.gov (United States)

He, Chenguang; Zhao, Li; Lin, Liulan; Gu, Huijie; Zhou, Heng; Cui, Lei

2010-07-01

Calcium phosphate bioceramics has a broad application prospect because of good biocompatibility, but porous scaffolds with complex shape can not be prepared by the traditional methods. To fabricate porous calcium phosphate ceramics by rapid prototyping and to investigate the in vitro osteogenic activities. The porous calcium phosphate ceramics was fabricated by rapid prototyping. The bone marrow mesenchymal stem cells (BMSCs) were isolated from bone marrow of Beagle canine, and the 3rd passage BMSCs were seeded onto the porous ceramics. The cell/ceramics composite cultured in osteogenic medium were taken as the experimental group (group A) and the cell/ceramics composite cultured in growth medium were taken as the control group (group B). Meanwhile, the cells seeded on the culture plate were cultured in osteogenic medium or growth medium respectively as positive control (group C) or negative control (group D). After 1, 3, and 7 days of culture, the cell proliferation and osteogenic differentiation on the porous ceramics were evaluated by DNA quantitative analysis, histochemical staining and alkaline phosphatase (ALP) activity. After DiO fluorescent dye, the cell adhesion, growth, and proliferation on the porous ceramics were also observed by confocal laser scanning microscope (CLSM). DNA quantitative analysis results showed that the number of BMSCs in all groups increased continuously with time. Plateau phase was not obvious in groups A and B, but it was clearly observed in groups C and D. The CLSM observation indicated that the activity of BMSCs was good and the cells spread extensively, showing good adhesion and proliferation on the porous calcium phosphate ceramics prepared by rapid prototyping. ALP quantitative analysis results showed that the stain of cells on the ceramics became deeper and deeper with time in groups A and B, the staining degree in group A were stronger than that in group B. There was no significant difference in the change of the ALP activity

[Geriatric health promotion and prevention for independently living senior citizens: programmes and target groups].

Science.gov (United States)

Dapp, U; Anders, J; Meier-Baumgartner, H P; v Renteln-Kruse, W

2007-08-01

Nearly all diseases in old age that are epidemiologically important can be reduced or prevented successfully through consequent changes in individual lifestyle, a systematic provision of measures in primary prevention (i.e. vaccination programmes) and the creation of health promoting settings. However, at the moment the amount of potential for preventative interventions is neither systematically nor sufficiently utilised in Germany. Two different preventative approaches: a) multidimensional advice session in small groups through an interdisciplinary team at a geriatric centre (seniors come to seek advice offered at a centre) or b) multidimensional advice at the seniors home through one member of the interdisciplinary team from the geriatric centre (expert takes advice to seniors home) were tested simultaneously with a well-described study sample of 804 independent community-dwelling senior citizens aged 60 years or over, without need of care and cognitive impairments recruited from general practices. Information about target group specific approaches in health promotion and prevention for senior citizens were retrieved from analyses of sociodemographic, medical, psychological and spacial characteristics of this study sample. The majority of the study sample (580 out of 804 or 72.1%) decided to participate: a) 86.7% (503 out of 580) attended at the geriatric centre and sought advice in group sessions and b) 13.3% (77 out of 580) decided to receive advice in a preventive home visit. A total of 224 seniors (224 out of 804 or 27.9%) refused to participate at all. These three target groups were characterised on the basis of their age, gender, education, social background, health status, health behaviour, use of preventive care, self perceived health, functional disabilities, social net and social participation and distance or accessibility of preventative approaches. The 503 senior citizens who participated in small group sessions at the geriatric centre were

Fabricating architectural volume

DEFF Research Database (Denmark)

Feringa, Jelle; Søndergaard, Asbjørn

2015-01-01

The 2011 edition of Fabricate inspired a number of collaborations, this article seeks to highlight three of these. There is a common thread amongst the projects presented: sharing the ambition to close the rift between design and fabrication while incorporating structural design aspects early on...

Fabrication and properties of yttrium doped barium titanate film by RF sputtering

International Nuclear Information System (INIS)

Igarashi, H.; Yuasa, M.; Okazaki, K.

1985-01-01

Semiconductive barium titanate films were fabricated by RF sputtering on fused quartz, alumina and barium titanate ceramic substrates using barium titanate ceramic with a small amount of yttria as a target. The films on the barium titanate substrates turned blue color and showed a small PTC effect by heat-treating at 1000 0 C in the air after deposition at the substrate temperature of 600 0 C

Fabrication of targets for transmutation of americium : synthesis of inertial matrix by sol-gel method. Procedure study on the infiltration of a radioactive solutions; Fabricacion de blancos para la transmutacion de americio: sintesis de matrices inertes por el metodo sol-gel. Estudio del procedimiento de infiltracion de disoluciones radiactivas

Energy Technology Data Exchange (ETDEWEB)

Fernandez Carretero, A [Universidad Complutense de Madrid (Spain)

2002-07-01

Transmutation and incineration are innovative options in the management and disposal of fission products and actinides. nevertheless, the fabrication of targets for transmutation and incineration of actinides and fission products require a reconsideration of conventional processes (mechanical blending) and the development of new procedures compatible with the high activity of these materials. This work presents th R and D of a new fabrication method called INRAM (Infiltration of Radioactive Materials) based on the infiltration of an actinide solution in a porous non radiotoxic material in the form of a pellet (up to 12% An), or beads (up to 40% An) produced by sol-gel. The first method have been used for the fabrication of spinel (MgAl{sub 2}O{sub 4}) targets containing 11% Am, which have been irradiated in HFR-Petten (358.4 full power days). Post-test burn-up calculations showed that at the end of the irradiation the initial Am-241 concentration was reduced to 4%. The fraction of the initial americum atoms that have been fissioned is 28%. The main advantage of the INRAM method is that matrices with low or zero activity can be fabricated and formed into the required shape in an unshielded facility. This method offers other advantages over conventional ones, such as the active wastes are reduced, is easy to automate, adoptable to telemanipulation and dust free, which facilitate operator intervention and minimise radiation exposure to the personal. In addition, the infiltrant needs only be present in liquid form, i. e. it could be transferred directly from the reprocessing plant for fabrication into targets without conversion into-solid form. In order to optimise the infiltration process in depth investigations of all important process parameters, e. g. infiltration kinetics and metal (pu, Am) concentration in the feed solution, and also on extensive study or powder metallurgy parameters for the preparation of high quality fuel pellets with a high density, have been

A honeycomb sandwich structure vacuum jacket for cryogenic targets

International Nuclear Information System (INIS)

Harada, M.; Kasai, S.; Kato, S.

1988-11-01

Cryogenic targets (H 2 , D 2 and 4 He) have been built for use in the study of photonuclear reactions with π sr spectrometer, TAGX at the 1.3 GeV Tokyo electron synchrotron. A new type of vacuum jacket fabricated from plastic honeycomb core and Mylar skins has been used in the target system for more than 5000 hours. The average radiation thickness and the average density of this jacket are measured to be 3.3 x 10 -3 X 0 and 0.15 g/cm 3 , respectively. (author)

Identifying HIV most-at-risk groups in Malawi for targeted interventions. A classification tree model.

Science.gov (United States)

Emina, Jacques B O; Madise, Nyovani; Kuepie, Mathias; Zulu, Eliya M; Ye, Yazoume

2013-05-28

To identify HIV-socioeconomic predictors as well as the most-at-risk groups of women in Malawi. A cross-sectional survey. Malawi The study used a sample of 6395 women aged 15-49 years from the 2010 Malawi Health and Demographic Surveys. Individual HIV status: positive or not. Findings from the Pearson χ(2) and χ(2) Automatic Interaction Detector analyses revealed that marital status is the most significant predictor of HIV. Women who are no longer in union and living in the highest wealth quintiles households constitute the most-at-risk group, whereas the less-at-risk group includes young women (15-24) never married or in union and living in rural areas. In the light of these findings, this study recommends: (1) that the design and implementation of targeted interventions should consider the magnitude of HIV prevalence and demographic size of most-at-risk groups. Preventive interventions should prioritise couples and never married people aged 25-49 years and living in rural areas because this group accounts for 49% of the study population and 40% of women living with HIV in Malawi; (2) with reference to treatment and care, higher priority must be given to promoting HIV test, monitoring and evaluation of equity in access to treatment among women in union disruption and never married or women in union aged 30-49 years and living in urban areas; (3) community health workers, households-based campaign, reproductive-health services and reproductive-health courses at school could be used as canons to achieve universal prevention strategy, testing, counselling and treatment.

Availability of enriched isotopic material for accelerator targets

International Nuclear Information System (INIS)

Newman, E.

1982-01-01

The electromagnetic isotope enrichment facility at ORNL provides a broad spectrum of highly enriched stable isotopes to the worldwide scientific community. The continued timely availability of these materials is of vital importance in many areas of basic research and, in particular, as source material for the fabrication of accelerator targets. A brief description of the facility and its capabilities and limitations is presented

Concept and experimental studies on fuel and target for minor actinides and fission products transmutation

Energy Technology Data Exchange (ETDEWEB)

Prunier, C; Guerin, Y [CEA Centre d` Etudes de Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. d` Etudes des Combustibles; Salvatores, M [CEA Centre d` Etudes de Cadarache, 13 - Saint-Paul-lez-Durance (France). Direction des Reacteurs Nucleaires; Zaetta, A [CEA Centre d` Etudes de Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. d` Etudes des Reacteurs

1994-12-31

High activity long-lived radionuclides in nuclear wastes, namely minor actinides (americium and neptunium) are in large amount generated by current nuclear reactive. The destruction of these radionuclides is a part of the French SPIN (Partitioning and Burning) program consistent with the determination to send a minimum amount of harmful products for final storage. Transmutation concepts are defined for neptunium and americium taking into account fuel cycle strategies. Neptunium destruction does not pose any major problems. It`s a by-product of uranium consumption, as plutonium and in despite of a slight gamma activity due to the protactinium 233 it`s quite easy to handle. Diluting neptunium in the mixed oxide fuels (MOX) should not be an obstacle for fabrication, in-pile behaviour and reprocessing either. Consequently we make the proposal of homogeneous mode of neptunium in MOX which should be soon explored in the experimental OSIRIS reactor and in the Phenix and Superphenix reactors. The analysis is more complex for the multi isotope americium. Its destruction is difficult because of gamma radioactivity which complicates fabrication. Experiments in Phenix and calculation showed that Phenix reactor offers a good potential for americium incineration, but similar data do not exist for PWR. It will remain a well known difficulty for fabrication and reprocessing. In this case we have to put a real new face to the fabrication flow-sheet of americium compounds and we propose to develop the heterogeneous mode. Targets choice are defined in term of: -safety, considering fuel reaction with cladding and water sodium, -transmutation rate, limited by target behaviour, in FR`s (Phenix), PWR`s (OSIRIS) and HFR (Petten), -reprocessing, checking the solubility of such targets by Purex process. So, at the beginning of our program the account has been on improving fuel and targets properties related to safety and fuel cycle. (authors). 4 figs.

Fabrication of Durably Superhydrophobic Cotton Fabrics by Atmospheric Pressure Plasma Treatment with a Siloxane Precursor

Directory of Open Access Journals (Sweden)

Jing Yang

2018-04-01

Full Text Available The surface treatment of fabrics in an atmospheric environment may pave the way for commercially viable plasma modifications of fibrous matters. In this paper, we demonstrate a durably superhydrophobic cotton cellulose fabric prepared in a single-step graft polymerization of hexamethyldisiloxane (HMDSO by N2 and O2 atmospheric pressure plasma. We systematically investigated effects on contact angle (CA and surface morphology of the cotton fabric under three operational parameters: precursor value; ionization gas flow rate; and plasma cycle time. Surface morphology, element composition, chemical structure and hydrophobic properties of the treated fabric were characterized by scanning electron microscope (SEM, EDS, FTIR and CA on the fabrics. The results indicated that a layer of thin film and nano-particles were evenly deposited on the cotton fibers, and graft polymerization occurred between cellulose and HMDSO. The fabric treated by O2 plasma exhibited a higher CA of 162° than that treated by N2 plasma which was about 149°. Furthermore, the CA of treated fabrics decreased only 0°~10° after storing at the ambient conditions for four months, and treated fabrics could also endure the standard textile laundering procedure in AATCC 61-2006 with minimum change. Therefore, this single-step plasma treatment method is shown to be a novel and environment-friendly way to make durable and superhydrophobic cotton fabrics.

Techniques for fabricating an infrared optical pyrometry system for pulsed electron beam diagnostics

International Nuclear Information System (INIS)

Ouellette, A.L.

1976-01-01

A description is given of an infrared optical pyrometry system which was designed to make fast time resolved temperature measurements. The purpose of this equipment is to determine the amount of energy from an electron beam or some other type of pulsed energy deposition that is absorbed in a target. The system is capable of measuring energy deposition levels up to 4000 J/g in carbon, which corresponds to a graphite target temperature of 2200 0 C. Methods of fabrication, alignment, and calibration are presented. The measurement of absorbed energy in a target as a function of position and depth is discussed as a possible application, and several measurements are described which permit a comparison of results from this system with those taken by other methods

Cigarette advertising in Mumbai, India: targeting different socioeconomic groups, women, and youth

Science.gov (United States)

Bansal, R; John, S; Ling, P

2005-01-01

Background: Despite a recent surge in tobacco advertising and the recent advertising ban (pending enforcement at the time of this study), there are few studies describing current cigarette marketing in India. This study sought to assess cigarette companies' marketing strategies in Mumbai, India. Methods: A two week field study was conducted in Mumbai in September 2003, observing, documenting, and collecting cigarette advertising on billboards, storefronts and at point of sale along two major thoroughfares, and performing a content analysis of news, film industry, and women's magazines and three newspapers. Results: Cigarette advertising was ubiquitous in the environment, present in news and in film magazines, but not in women's magazines or the newspapers. The four major advertising campaigns all associated smoking with aspiration; the premium brands targeting the higher socioeconomic status market utilised tangible images of westernisation and affluence whereas the "bingo" (low priced) segment advertisements invited smokers to belong to a league of their own and "rise to the taste" using intangible images. Women were not depicted smoking, but were present in cigarette advertisements—for example, a woman almost always accompanied a man in "the man with the smooth edge" Four Square campaign. Advertisements and product placements at low heights and next to candies at point of sale were easily accessible by children. In view of the iminent enforcement of the ban on tobacco advertisements, cigarette companies are increasing advertising for the existing brand images, launching brand extensions, and brand stretching. Conclusion: Cigarette companies have developed sophisticated campaigns targeting men, women, and children in different socioeconomic groups. Many of these strategies circumvent the Indian tobacco advertising ban. Understanding these marketing strategies is critical to mimimise the exploitation of loopholes in tobacco control legislation. PMID:15923471

LEMA facility and equipments for minor actinides compounds fabrication and characterisation

Energy Technology Data Exchange (ETDEWEB)

Donnet, L. [Commissariat a l' Energie Atomique - CEA, CEA/DEN/VRH/DTEC/SDTC/LEMA (France)

2008-07-01

The LEMA (Actinide based materials study laboratory) is mainly involved in minor actinides materials development and fabrication, from raw materials choice and synthesis to finished products including pin assembly. The aim of the technological analyses is to establish choices of raw materials and manufacturing techniques. The LEMA is located in the ATALANTE facility in Marcoule. It consists in two shielded chains (one specific for neutrons) and three hot laboratories. The laboratory has various apparatuses in hot cells such as: ball mills, press, dilatometer, TGA (thermo-gravimetry analyser), calcination and sintering furnaces (2000 deg. C). The laboratory has also characterisation apparatuses such as XRD and SEM (scanning electron microscopy) dedicated to structural and microstructural studies. Thanks to the diversity of its equipment, the LEMA has well established worldwide collaborations and takes part in international fuels/target fabrication and irradiation experiments. (author)

LEMA facility and equipments for minor actinides compounds fabrication and characterisation

International Nuclear Information System (INIS)

Donnet, L.

2008-01-01

The LEMA (Actinide based materials study laboratory) is mainly involved in minor actinides materials development and fabrication, from raw materials choice and synthesis to finished products including pin assembly. The aim of the technological analyses is to establish choices of raw materials and manufacturing techniques. The LEMA is located in the ATALANTE facility in Marcoule. It consists in two shielded chains (one specific for neutrons) and three hot laboratories. The laboratory has various apparatuses in hot cells such as: ball mills, press, dilatometer, TGA (thermo-gravimetry analyser), calcination and sintering furnaces (2000 deg. C). The laboratory has also characterisation apparatuses such as XRD and SEM (scanning electron microscopy) dedicated to structural and microstructural studies. Thanks to the diversity of its equipment, the LEMA has well established worldwide collaborations and takes part in international fuels/target fabrication and irradiation experiments. (author)

Fabrication of colloidal crystal heterostructures by a room temperature floating self-assembly method

International Nuclear Information System (INIS)

Wang Aijun; Chen Shengli; Dong Peng

2011-01-01

Highlights: → Opal colloidal crystal heterostructure of several square centimeters in area was fabricated within only tens of minutes. → A fabricated colloidal crystal heterostructure was composed of a PS opal and a TiO 2 inverse opal crystal films. → The photonic heterostructure had two photonic-band gaps. → The relative position of the two photonic-band gaps can be controlled by the size of PS microspheres used to fabricate the photonic heterostructure. - Abstract: Photonic crystal heterostructures were fabricated through a room temperature floating self-assembly (RTFSA) method recently developed by our research group. Applying this method, opal colloidal crystal heterostructures of several square centimeters in area were fabricated within tens of minutes without special facilities, and a heterostructure composed of a PS opal and a TiO 2 inverse opal crystal films was fabricated. SEM image of the PS opal-TiO 2 inverse opal heterostructure showed the ordered growth of the top opal film of the heterostructure was hardly disturbed by the cracks in the TiO 2 inverse opal film. The UV-vis transmission spectra indicated that the photonic heterostructures had two photonic-band gaps, and the relative position of two photonic-band gaps can be controlled by the size of PS microspheres used to fabricated the photonic heterostructures.

Target Temperature Management after out-of-hospital cardiac arrest--a randomized, parallel-group, assessor-blinded clinical trial--rationale and design

DEFF Research Database (Denmark)

Nielsen, Niklas; Wetterslev, Jørn; al-Subaie, Nawaf

2012-01-01

Experimental animal studies and previous randomized trials suggest an improvement in mortality and neurologic function with induced hypothermia after cardiac arrest. International guidelines advocate the use of a target temperature management of 32°C to 34°C for 12 to 24 hours after resuscitation...... from out-of-hospital cardiac arrest. A systematic review indicates that the evidence for recommending this intervention is inconclusive, and the GRADE level of evidence is low. Previous trials were small, with high risk of bias, evaluated select populations, and did not treat hyperthermia...... in the control groups. The optimal target temperature management strategy is not known....

Effect of fire retardants on cotton fabric grafted with acrylic acid by EB radiation: a thermal analysis study

International Nuclear Information System (INIS)

Mitra, D.; Sabharwal, S.; Majali, A.B.

1998-01-01

Electron beam irradiation technique has been utilized to graft acrylic acid to cotton fabric in order to provide suitable functional groups that can subsequently react with urea or borax for making the fabric fire resistant. Thermal analytical technique such as, DSC and TG have been utilized to investigate the flame retardency characteristic of the grafted and treated fabric. The result shows that decay curve of exothermic peak due to combustion of cotton fabric in case of urea treated fabric at 330 degC becomes broad and shifts to higher temperature in DSC analysis as compared to pure cotton fabric and char residue in TG analysis is 20% in both the case. In borax treated fabric, char residue is found to be 40% in TG analysis and DSC profile is similar to that of urea treated fabric. (author)

Effect of Biopolishing On Warm–Cool Feeling of Knitted Fabric: A Subjective and An Objective Evaluations

Directory of Open Access Journals (Sweden)

Mangat Asif

2017-06-01

Full Text Available Soft and clean surface of fabric without any floating fibers is one of the factors important for better marketing of clothing. The most common method for having such clean fabric surface is the removal of protruding (floating fiber from the surface of the fabric. Many studies have proved that enzymatic treatment, commonly called biopolishing, removes the floating fibers from the surface of fabric and gives a smooth surface to the fabric. This study is an effort to assess and measure the impact of biopolishing of knitted fabric through objective and subjective evaluation on warm-cool feeling of fabric because of change in surface profile of the fabric. For testing purposes, 31 knitted fabric samples of various kinds were produced. Alambeta has been used for measuring thermal absorptivity values of fabric. Thermal absorptivity is an indicator of warm-cool feeling. For subjective evaluation, a group of 30 people were asked to give their opinion about warm-cool feeling. Both subjective and objective assessments confirm that biopolishing has a significant impact on warm-cool feeling. Fabric gives cool feeling after biopolishing. This study explores that clean surface will have higher thermal absorptivity and will give cool feeling when it will be touched by human skin.

SU-8 cantilevers for bio/chemical sensing; Fabrication, characterisation and development of novel read-out methods

DEFF Research Database (Denmark)

Nordström, M.; Keller, Stephan Urs; Lillemose, Michael

2008-01-01

Here, we present the activities within our research group over the last five years with cantilevers fabricated in the polymer SU-8. We believe that SU-8 is an interesting polymer for fabrication of cantilevers for bio/chemical sensing due to its simple processing and low Young's modulus. We show...

Structure and yarn sensor for fabric

Science.gov (United States)

Mee, D.K.; Allgood, G.O.; Mooney, L.R.; Duncan, M.G.; Turner, J.C.; Treece, D.A.

1998-10-20

A structure and yarn sensor for fabric directly determines pick density in a fabric thereby allowing fabric length and velocity to be calculated from a count of the picks made by the sensor over known time intervals. The structure and yarn sensor is also capable of detecting full length woven defects and fabric. As a result, an inexpensive on-line pick (or course) density measurement can be performed which allows a loom or knitting machine to be adjusted by either manual or automatic means to maintain closer fiber density tolerances. Such a sensor apparatus dramatically reduces fabric production costs and significantly improves fabric consistency and quality for woven or knitted fabric. 13 figs.

Fabrics in Function

DEFF Research Database (Denmark)

Bang, Anne Louise

2007-01-01

sensing of fabrics in function. It is proposed that tactile and visual sensing of fabrics is a way to investigate and express emotional utility values. The further purpose is to use experiments with repertory grid models as part of the mapping of the entire research project and also as a basis...

Elective Clinical Target Volumes for Conformal Therapy in Anorectal Cancer: A Radiation Therapy Oncology Group Consensus Panel Contouring Atlas

International Nuclear Information System (INIS)

Myerson, Robert J.; Garofalo, Michael C.; El Naqa, Issam; Abrams, Ross A.; Apte, Aditya; Bosch, Walter R.; Das, Prajnan; Gunderson, Leonard L.; Hong, Theodore S.; Kim, J.J. John; Willett, Christopher G.; Kachnic, Lisa A.

2009-01-01

Purpose: To develop a Radiation Therapy Oncology Group (RTOG) atlas of the elective clinical target volume (CTV) definitions to be used for planning pelvic intensity-modulated radiotherapy (IMRT) for anal and rectal cancers. Methods and Materials: The Gastrointestinal Committee of the RTOG established a task group (the nine physician co-authors) to develop this atlas. They responded to a questionnaire concerning three elective CTVs (CTVA: internal iliac, presacral, and perirectal nodal regions for both anal and rectal case planning; CTVB: external iliac nodal region for anal case planning and for selected rectal cases; CTVC: inguinal nodal region for anal case planning and for select rectal cases), and to outline these areas on individual computed tomographic images. The imaging files were shared via the Advanced Technology Consortium. A program developed by one of the co-authors (I.E.N.) used binomial maximum-likelihood estimates to generate a 95% group consensus contour. The computer-estimated consensus contours were then reviewed by the group and modified to provide a final contouring consensus atlas. Results: The panel achieved consensus CTV definitions to be used as guidelines for the adjuvant therapy of rectal cancer and definitive therapy for anal cancer. The most important difference from similar atlases for gynecologic or genitourinary cancer is mesorectal coverage. Detailed target volume contouring guidelines and images are discussed. Conclusion: This report serves as a template for the definition of the elective CTVs to be used in IMRT planning for anal and rectal cancers, as part of prospective RTOG trials.

Atomic Force Microscopy Probing of Receptor–Nanoparticle Interactions for Riboflavin Receptor Targeted Gold–Dendrimer Nanocomposites

Science.gov (United States)

2015-01-01

Riboflavin receptors are overexpressed in malignant cells from certain human breast and prostate cancers, and they constitute a group of potential surface markers important for cancer targeted delivery of therapeutic agents and imaging molecules. Here we report on the fabrication and atomic force microscopy (AFM) characterization of a core–shell nanocomposite consisting of a gold nanoparticle (AuNP) coated with riboflavin receptor-targeting poly(amido amine) dendrimer. We designed this nanocomposite for potential applications such as a cancer targeted imaging material based on its surface plasmon resonance properties conferred by AuNP. We employed AFM as a technique for probing the binding interaction between the nanocomposite and riboflavin binding protein (RfBP) in solution. AFM enabled precise measurement of the AuNP height distribution before (13.5 nm) and after chemisorption of riboflavin-conjugated dendrimer (AuNP–dendrimer; 20.5 nm). Binding of RfBP to the AuNP–dendrimer caused a height increase to 26.7 nm, which decreased to 22.8 nm when coincubated with riboflavin as a competitive ligand, supporting interaction of AuNP–dendrimer and its target protein. In summary, physical determination of size distribution by AFM imaging can serve as a quantitative approach to monitor and characterize the nanoscale interaction between a dendrimer-covered AuNP and target protein molecules in vitro. PMID:24571134

Fabrication and Prototyping Lab

Data.gov (United States)

Federal Laboratory Consortium — Purpose: The Fabrication and Prototyping Lab for composite structures provides a wide variety of fabrication capabilities critical to enabling hands-on research and...

Electroless or autocatalytic coating of microparticles for laser fusion targets

International Nuclear Information System (INIS)

Mayer, A.; Catlett, D.S.

1977-04-01

Use of a novel device for applying uniform metallic coatings to spherical microparticles is described. The apparatus deposits electroless metal coatings on hollow, thin-walled metal or sensitized nonmetallic micromandrels. The apparatus and process were developed for fabrication of microsphere pressure vessels for use as targets in laser-initiated fusion research

A facile fabrication of multifunctional knit polyester fabric based on chitosan and polyaniline polymer nanocomposite

Science.gov (United States)

Tang, Xiaoning; Tian, Mingwei; Qu, Lijun; Zhu, Shifeng; Guo, Xiaoqing; Han, Guangting; Sun, Kaikai; Hu, Xili; Wang, Yujiao; Xu, Xiaoqi

2014-10-01

Knit polyester fabric was successively modified and decorated with chitosan layer and polyaniline polymer nanocomposite layer in this paper. The fabric was firstly treated with chitosan to form a stable layer through the pad-dry-cure process, and then the polyaniline polymer nanocomposite layer was established on the outer layer by in situ chemical polymerization method using ammonium persulfate as oxidant and chlorhydric acid as dopant. The surface morphology of coated fabric was characterized by scanning electron microscopy (SEM), and the co-existence of chitosan layer and granular polyaniline polymer nanocomposite was confirmed and well dispersed on the fabric surface. The resultant fabric was endowed with remarkable electrical conductivity properties and efficient water-repellent capability, which also have been found stable after water laundering. In addition, the photocatalytic decomposition activity for reactive red dye was observed when the multifunctional knit polyester fabric was exposed to the illumination of ultraviolet lamp. These results indicated that chitosan and polyaniline polymer nanocomposite could form ideal multifunctional coatings on the surface of knit polyester fabric.

In vitro evaluation of marginal adaptation in five ceramic restoration fabricating techniques.

Science.gov (United States)

Ural, Cağri; Burgaz, Yavuz; Saraç, Duygu

2010-01-01

To compare in vitro the marginal adaptation of crowns manufactured using ceramic restoration fabricating techniques. Fifty standardized master steel dies simulating molars were produced and divided into five groups, each containing 10 specimens. Test specimens were fabricated with CAD/CAM, heat-press, glass-infiltration, and conventional lost-wax techniques according to manufacturer instructions. Marginal adaptation of the test specimens was measured vertically before and after cementation using SEM. Data were statistically analyzed by one-way ANOVA with Tukey HSD tests (a = .05). Marginal adaptation of ceramic crowns was affected by fabrication technique and cementation process (P cementation (P cementation. Marginal adaptation values obtained in the compared systems were within clinically acceptable limits. Cementation causes a significant increase in the vertical marginal discrepancies of the test specimens.

Fabrication of Well-Ordered, Anodic Aluminum Oxide Membrane Using Hybrid Anodization.

Science.gov (United States)

Kim, Jungyoon; Ganorkar, Shraddha; Choi, Jinnil; Kim, Young-Hwan; Kim, Seong-II

2017-01-01

Anodic Aluminum Oxide (AAO) is one of the most favorable candidates for fabrication of nano-meshed membrane for various applications due to its controllable pore size and self-ordered structure. The mechanism of AAO membrane is a simple and has been studied by many research groups, however the actual fabrication of membrane has several difficulties owing to its sensitivity of ordering, long anodizing time and unclearness of the pore. In this work, we have demonstrated enhanced process of fabrication symmetric AAO membrane by using “hybrid anodizing” (Hyb-A) method which include mild anodization (MA) followed by hard anodization (HA). This Hyb-A process can give highly ordered membrane with more vivid pore than two-step anodizing process. HA was implemented on the Al plate which has been already textured by MA for more ordered structure and HA plays a key role for formation of more obvious pore in Hyb-A. Our experimental results indicate that Hyb-A with proper process sequence would be one of the fast and useful fabrication methods for the AAO membrane.

A cryostat to hold frozen-spin polarized HD targets in CLAS: HDice-II

Energy Technology Data Exchange (ETDEWEB)

Lowry, M.M., E-mail: mlowry@jlab.org [Thomas Jefferson National Accelerator Facility, 12000 Jefferson Avenue, Newport News, VA 23606 (United States); Bass, C.D. [Thomas Jefferson National Accelerator Facility, 12000 Jefferson Avenue, Newport News, VA 23606 (United States); D' Angelo, A. [Thomas Jefferson National Accelerator Facility, 12000 Jefferson Avenue, Newport News, VA 23606 (United States); Universita' di Roma ‘Tor Vergata’, and INFN Sezione di Roma ‘Tor Vergata’, Via della Ricerca Scientifica, 1, I-00133 Roma (Italy); Deur, A.; Dezern, G. [Thomas Jefferson National Accelerator Facility, 12000 Jefferson Avenue, Newport News, VA 23606 (United States); Hanretty, C. [University of Virginia, 1400 University Avenue, Charlottesville, VA 22903 (United States); Ho, D. [Carnegie-Mellon University, 5000 Forbes Avenue, Pittsburgh, PA 15213 (United States); Kageya, T.; Kashy, D. [Thomas Jefferson National Accelerator Facility, 12000 Jefferson Avenue, Newport News, VA 23606 (United States); Khandaker, M. [Norfolk State University, 700 Park Avenue, Norfolk, VA 23504 (United States); Laine, V. [Thomas Jefferson National Accelerator Facility, 12000 Jefferson Avenue, Newport News, VA 23606 (United States); Université Blaise Pascal, 34 Avenue Carnot, 63000 Clermont-Ferrand (France); O' Connell, T. [University of Connecticut, 115 N Eagleville Road, Storrs-Mansfield, CT 06269 (United States); Pastor, O. [Thomas Jefferson National Accelerator Facility, 12000 Jefferson Avenue, Newport News, VA 23606 (United States); Peng, P. [University of Virginia, 1400 University Avenue, Charlottesville, VA 22903 (United States); Sandorfi, A.M. [Thomas Jefferson National Accelerator Facility, 12000 Jefferson Avenue, Newport News, VA 23606 (United States); Sokhan, D. [Institut de Physique Nucleaire, Bat 100 – M053, Orsay 91406 (France); and others

2016-04-11

The design, fabrication, operation, and performance of a {sup 3/4}He dilution refrigerator and superconducting magnet system for holding a frozen-spin polarized hydrogen deuteride target in the Jefferson Laboratory CLAS detector during photon beam running is reported. The device operates both vertically (for target loading) and horizontally (for target bombardment). The device proves capable of maintaining a base temperature of 50 mK and a holding field of 1 T for extended periods. These characteristics enabled multi-month polarization lifetimes for frozen spin HD targets having proton polarization of up to 50% and deuteron up to 27%.

Silicon Nano fabrication by Atomic Force Microscopy-Based Mechanical Processing

International Nuclear Information System (INIS)

Miyake, Sh.; Wang, M.; Kim, J.

2014-01-01

This paper reviews silicon nano fabrication processes using atomic force microscopy (AFM). In particular, it summarizes recent results obtained in our research group regarding AFM-based silicon nano fabrication through mechanochemical local oxidation by diamond tip sliding, as well as mechanical, electrical, and electromechanical processing using an electrically conductive diamond tip. Microscopic three-dimensional manufacturing mainly relies on etching, deposition, and lithography. Therefore, a special emphasis was placed on nano mechanical processes, mechanochemical reaction by potassium hydroxide solution etching, and mechanical and electrical approaches. Several important surface characterization techniques consisting of scanning tunneling microscopy and related techniques, such as scanning probe microscopy and AFM, were also discussed.

Magnetron co-sputtering system for coating ICF targets

International Nuclear Information System (INIS)

Hsieh, E.J.; Meyer, S.F.; Halsey, W.G.; Jameson, G.T.; Wittmayer, F.J.

1981-01-01

Fabrication of Inertial Confinement Fusion (ICF) targets requires deposition of various types of coatings on microspheres. The mechanical strength, and surface finish of the coatings are of concern in ICF experiments. The tensile strength of coatings can be controlled through grain refinement, selective doping and alloy formation. We have constructed a magnetron co-sputtering system to produce variable density profile coatings with high tensile strength on microspheres

Changes in sexual behavior of HIV-infected older adults enrolled in a clinical trial of standalone group psychotherapies targeting depression

Science.gov (United States)

Lovejoy, Travis I.; Heckman, Timothy G.; Sikkema, Kathleen J.; Hansen, Nathan B.; Kochman, Arlene

2014-01-01

By 2015, one-half of all HIV-positive persons in the U.S. will be 50-plus years of age, and as many as 30% of older adults living with HIV/AIDS continue to engage in unprotected sexual intercourse. Contemporary positive prevention models often include mental health treatment as a key component of HIV prevention interventions. This secondary data analysis characterized longitudinal patterns of sexual behavior in HIV-positive older adults enrolled in a randomized controlled trial of group mental health interventions and assessed the efficacy of psychosocial treatments that targeted depression to reduce sexual risk behavior. Participants were 295 HIV-positive adults ≥ 50 years of age experiencing mild to severe depressive symptoms, randomized to one of three study conditions: a 12-session coping improvement group intervention, a 12-session interpersonal support group intervention, or individual therapy upon request. Approximately one-fifth of participants reported one or more occasions of unprotected anal or vaginal intercourse with HIV-negative sexual partners or persons of unknown HIV serostatus over the study period. Changes in sexual behavior did not vary by intervention condition, indicating that standalone treatments that target and reduce depression may be insufficient to reduce sexual risk behavior in depressed HIV-positive older adults. PMID:24668254

14 CFR 29.605 - Fabrication methods.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fabrication methods. 29.605 Section 29.605... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction General § 29.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process...

The Areva Group; Le groupe Areva

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-08-01

This document provides information on the Areva Group, a world nuclear industry leader, offering solutions for nuclear power generation, electricity transmission and distribution and interconnect systems to the telecommunications, computer and automotive markets. It presents successively the front end division including the group business lines involved in producing nuclear fuel for electric power generation (uranium mining, concentration, conversion and enrichment and nuclear fuel fabrication); the reactors and services division which designs and builds PWR, BWR and research reactors; the back end division which encompasses the management of the fuel that has been used in nuclear power plants; the transmission and distribution division which provides products, systems and services to the medium and high voltage energy markets; the connectors division which designs and manufactures electrical, electronic and optical connectors, flexible micro circuitry and interconnection systems. Areva is implemented in Europe, north and south america, africa and asia-pacific. (A.L.B.)

Animal Rights Groups Target High School Dissection.

Science.gov (United States)

Trotter, Andrew

1992-01-01

Two groups leading the charge against dissection are People for the Ethical Treatment of Animals (PETA) and the Student Action Corps for Animals (SACA). Protests by student and community members remain the movement's strongest weapon. (MLF)

14 CFR 27.605 - Fabrication methods.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fabrication methods. 27.605 Section 27.605... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction General § 27.605 Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a fabrication process (such as...

14 CFR 25.605 - Fabrication methods.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fabrication methods. 25.605 Section 25.605... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction General § 25.605 Fabrication methods. (a) The methods of fabrication used must produce a consistently sound structure. If a fabrication process...

Antibacterial cotton fabric with enhanced durability prepared using silver nanoparticles and carboxymethyl chitosan.

Science.gov (United States)

Xu, QingBo; Xie, LiJing; Diao, Helena; Li, Fang; Zhang, YanYan; Fu, FeiYa; Liu, XiangDong

2017-12-01

Carboxymethyl chitosan (CMCTS) and silver nanoparticles (Ag NPs) were successfully linked onto a cotton fabric surface through a simple mist modification process. The CMCTS binder was covalently linked to the cotton fabric via esterification and the Ag NPs were tightly adhered to the fiber surface by coordination bonds with the amine groups of CMCTS. As a result, the coating of Ag NPs on the cotton fabric showed excellent antibacterial properties and laundering durability. After 50 consecutive laundering cycles, the bacterial reduction rates (BR) against both S. aureus and E. coli remained over 95%. It has potential applications in a wide variety of fields such as sportswear, socks, and medical textile. Copyright © 2017 Elsevier Ltd. All rights reserved.

Reducing Prejudice With Labels: Shared Group Memberships Attenuate Implicit Bias and Expand Implicit Group Boundaries.

Science.gov (United States)

Scroggins, W Anthony; Mackie, Diane M; Allen, Thomas J; Sherman, Jeffrey W

2016-02-01

In three experiments, we used a novel Implicit Association Test procedure to investigate the impact of group memberships on implicit bias and implicit group boundaries. Results from Experiment 1 indicated that categorizing targets using a shared category reduced implicit bias by increasing the extent to which positivity was associated with Blacks. Results from Experiment 2 revealed that shared group membership, but not mere positivity of a group membership, was necessary to reduce implicit bias. Quadruple process model analyses indicated that changes in implicit bias caused by shared group membership are due to changes in the way that targets are evaluated, not to changes in the regulation of evaluative bias. Results from Experiment 3 showed that categorizing Black targets into shared group memberships expanded implicit group boundaries. © 2015 by the Society for Personality and Social Psychology, Inc.

Development of technology for fabrication of lithium CPS on basis of CNT-reinforced carboxylic fabric

Energy Technology Data Exchange (ETDEWEB)

Tazhibayeva, Irina, E-mail: tazhibayeva@ntsc.kz [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan); Baklanov, Viktor; Ponkratov, Yuriy [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan); Abdullin, Khabibulla [Institute of Experimental and Theoretical Physics of Kazakh National University, Almaty (Kazakhstan); Kulsartov, Timur; Gordienko, Yuriy; Zaurbekova, Zhanna [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan); Lyublinski, Igor [JSC «Red Star», Moscow (Russian Federation); NRNU «MEPhI», Moscow (Russian Federation); Vertkov, Alexey [JSC «Red Star», Moscow (Russian Federation); Skakov, Mazhyn [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan)

2017-04-15

Highlights: • Preliminary study of carboxylic fabric wettability with liquid lithium is presented. • Preliminary studies of carboxylic fabric wettability with liquid lithium consist in carrying out of experiments at temperatures 673,773 and 873 К in vacuum during long time. • A scheme of experimental device for manufacturing of lithium CPS and matrix filling procedure with liquid lithium are presented. • The concept of lithium limiter with CPS on basis of CNT-reinforced carboxylic fabric is proposed. - Abstract: The paper describes the analysis of liquid lithium interaction with materials based on carbon, the manufacture technology of capillary-porous system (CPS) matrix on basis of CNT-reinforced carboxylic fabric. Preliminary study of carboxylic fabric wettability with liquid lithium is presented. The development of technology includes: microstructural studies of carboxylic fabric before its CNT-reinforcing; validation of CNT-reinforcing technology; mode validation of CVD-method for CNT synthesize; study of synthesized carbon structures. Preliminary studies of carboxylic fabric wettability with liquid lithium consist in carrying out of experiments at temperatures 673, 773 and 873 К in vacuum during long time. The scheme of experimental device for manufacturing of lithium CPS and matrix filling procedure with liquid lithium are presented. The concept of lithium limiter with CPS on basis of CNT-reinforced carboxylic fabric is proposed.

Development of technology for fabrication of lithium CPS on basis of CNT-reinforced carboxylic fabric

International Nuclear Information System (INIS)

Tazhibayeva, Irina; Baklanov, Viktor; Ponkratov, Yuriy; Abdullin, Khabibulla; Kulsartov, Timur; Gordienko, Yuriy; Zaurbekova, Zhanna; Lyublinski, Igor; Vertkov, Alexey; Skakov, Mazhyn

2017-01-01

Highlights: • Preliminary study of carboxylic fabric wettability with liquid lithium is presented. • Preliminary studies of carboxylic fabric wettability with liquid lithium consist in carrying out of experiments at temperatures 673,773 and 873 К in vacuum during long time. • A scheme of experimental device for manufacturing of lithium CPS and matrix filling procedure with liquid lithium are presented. • The concept of lithium limiter with CPS on basis of CNT-reinforced carboxylic fabric is proposed. - Abstract: The paper describes the analysis of liquid lithium interaction with materials based on carbon, the manufacture technology of capillary-porous system (CPS) matrix on basis of CNT-reinforced carboxylic fabric. Preliminary study of carboxylic fabric wettability with liquid lithium is presented. The development of technology includes: microstructural studies of carboxylic fabric before its CNT-reinforcing; validation of CNT-reinforcing technology; mode validation of CVD-method for CNT synthesize; study of synthesized carbon structures. Preliminary studies of carboxylic fabric wettability with liquid lithium consist in carrying out of experiments at temperatures 673, 773 and 873 К in vacuum during long time. The scheme of experimental device for manufacturing of lithium CPS and matrix filling procedure with liquid lithium are presented. The concept of lithium limiter with CPS on basis of CNT-reinforced carboxylic fabric is proposed.

New route to the fabrication of nanocrystalline diamond films

International Nuclear Information System (INIS)

Varshney, Deepak; Morell, Gerardo; Palomino, Javier; Resto, Oscar; Gil, Jennifer; Weiner, Brad R.

2014-01-01

Nanocrystalline diamond (NCD) thin films offer applications in various fields, but the existing synthetic approaches are cumbersome and destructive. A major breakthrough has been achieved by our group in the direction of a non-destructive, scalable, and economic process of NCD thin-film fabrication. Here, we report a cheap precursor for the growth of nanocrystalline diamond in the form of paraffin wax. We show that NCD thin films can be fabricated on a copper support by using simple, commonplace paraffin wax under reaction conditions of Hot Filament Chemical Vapor Deposition (HFCVD). Surprisingly, even the presence of any catalyst or seeding that has been conventionally used in the state-of-the-art is not required. The structure of the obtained films was analyzed by scanning electron microscopy and transmission electron microscopy. Raman spectroscopy and electron energy-loss spectroscopy recorded at the carbon K-edge region confirm the presence of nanocrystalline diamond. The process is a significant step towards cost-effective and non-cumbersome fabrication of nanocrystalline diamond thin films for commercial production

Preliminary results on the cryogenic target for FIREX project

International Nuclear Information System (INIS)

Iwamoto, A.; Maekawa, R.; Mito, T.; Okamoto, M.; Motojima, O.; Nakai, M.; Norimatsu, T.; Nagai, K.

2006-01-01

Preliminary tests on the cryogenic target for the fast ignition realization experiment (FIREX) project has been conducted. A foam shell method is proposed to realize its target design. A foam target consists of three parts: a foam shell, a conical laser guide and a liquid or gas feeder made of glass. The shell is a hollow sphere (500 μm in diameter) with a uniform and thin foam layer (about 20 μm in thickness). Epoxy resin is utilized to assemble the parts into the target. Liquid fuel is fed into the shell by the feeder and is soaked up by the foam material through capillarity. The fuel is then solidified. Regarding target fabrication, one of the concerns is the influence on various thermal contractions from the different materials when it is cooled down to cryogenic environment. This paper describes the result on the validity check at cryogenic environment and the demonstration of H 2 liquefaction using a dummy target instead of the foam target. Judging from these results, the target assembled in the same process as the dummy target is sure to be practicable for the FIREX project. (authors)

Strategic Targeted Advertising

NARCIS (Netherlands)

A. Galeotti; J.L. Moraga-Gonzalez (José Luis)

2003-01-01

textabstractWe present a strategic game of pricing and targeted-advertising. Firms can simultaneously target price advertisements to different groups of customers, or to the entire market. Pure strategy equilibria do not exist and thus market segmentation cannot occur surely. Equilibria exhibit

Reflection groups

International Nuclear Information System (INIS)

Eggermont, G.

2006-01-01

In 2005, PISA organised proactive meetings of reflection groups on involvement in decision making, expert culture and ethical aspects of radiation protection.All reflection group meetings address particular targeted audiences while the output publication in book form is put forward

Laser program annual report, 1979

Energy Technology Data Exchange (ETDEWEB)

Coleman, L.W.; Strack, J.R. (eds.)

1980-03-01

This volume contains four sections that covers the areas of target design, target fabrication, diagnostics, and experiments. Section 3 reports on target design activities, plasma theory and simulation, code development, and atomic theory. Section 4 presents the accomplishments of the target fabrication group, and Section 5 presents results of diagnostic developments and applications for the year. The results of laser-target experiments are presented. (MOW)

Laser program annual report, 1979

International Nuclear Information System (INIS)

Coleman, L.W.; Strack, J.R.

1980-03-01

This volume contains four sections that covers the areas of target design, target fabrication, diagnostics, and experiments. Section 3 reports on target design activities, plasma theory and simulation, code development, and atomic theory. Section 4 presents the accomplishments of the target fabrication group, and Section 5 presents results of diagnostic developments and applications for the year. The results of laser-target experiments are presented

Design and fabrication of a cryostat for low temperature mechanical testing for the Mechanical and Materials Engineering group at CERN

CERN Document Server

Aviles Santillana, I; Gerardin, A; Guinchard, M; Langeslag, S A E; Sgobba, S

2015-01-01

Mechanical testing of materials at low temperatures is one of the cornerstones of the Mechanical and Materials Engineering (MME) group at CERN. A long tradition of more than 20 years and a unique know - how of such tests has been developed with an 18 kN double-walled cryostat. Large campaigns of material qualification have been carried out and the mechanical behaviour of materials at 4 K has been vastly studied in sub - size samples for projects like LEP, LHC and its experiments. With the aim of assessing the mechanical properties of materials of higher strength and/or issued from heavy gauge products for which testing standardized specimens of larger cross section might be more adapted, a new 100 kN cryostat capable of hosting different shapes of normalized samples has been carefully designed and fabricated inhouse together with the associated tooling and measurement instrumentation. It has been conceived to be able to adapt to different test frames both dynamic and static, which will be of paramount importa...

Seasonal influenza vaccination coverage rate of target groups in selected cities and provinces in China by season (2009/10 to 2011/12.

Directory of Open Access Journals (Sweden)

Lei Zhou

Full Text Available BACKGROUND: The objectives of the survey were to identify the level of influenza vaccination coverage in China in three influenza seasons 2009/10 to 2011/12, and to find out potential predictors for seasonal influenza vaccination. METHODS: In September and October 2011, representative urban household telephone surveys were conducted in five provinces in China with a response rate of 6%. Four target groups were defined for analysis: 1 children ≤ 5 years old; 2 elderly persons aged ≥ 60 years old; 3 health care workers (persons working in the medical field and 4 chronically ill persons. RESULTS: The overall mean vaccination rate was 9.0%. Among the four target groups, the rate of vaccination of children aged ≤ 5 years old (mean = 26% was highest and the rate of elderly people aged ≥ 60 years old (mean = 7.4% was the lowest, while the rates of persons who suffer from a chronic illness (mean = 9.4% and health care workers (9.5% were similar. A subsidy for influenza vaccination, age group, health care workers, suffering from a chronic illness and living in Eastern China were independent significant predictors for influenza vaccination. CONCLUSIONS: The seasonal influenza vaccination coverage rates among urban populations in selected cities and provinces in China were far below previously reported rates in developed countries. Influenza vaccination coverage rates differed widely between different target groups and provinces in China. Subsidy policy might have a positive effect on influenza vaccination rate, but further cost-effectiveness studies, as well as the vaccination rate associated factors studies are still needed to inform strategies to increase coverage.

Blue and Black Cloth Targets: Effects of Size, Shape and Color on Stable Fly (L.) (Diptera: Muscidae) Attraction

Science.gov (United States)

Stable fly management has been challenging. Insecticide-treated targets made from blue and black fabric, developed in Africa, were evaluated in Louisiana and Florida to determine if they would attract and kill stable flies. Untreated targets were used to answer questions about configuration, size an...

Guidebook for the fabrication of non-destructive testing (NDT) test specimens

International Nuclear Information System (INIS)

2001-01-01

Non-destructive testing (NDT) test specimens constitute a very important part of training and certification of NDT personnel and are important for carrying out actual inspection and testing, and for achieving international harmonization of NDT practices. The IAEA organized an advisory group of experts to develop a Guidebook for Fabrication of NDT Test Specimens. The experts consulted the ISO/FDIS 9712-1999 requirements for training and certification of personnel and the suitability of various types of NDT test specimens that are needed to meet such requirements This guidebook presents a set of NDT test specimens, and the methodology and procedures for their fabrication

14 CFR 23.605 - Fabrication methods.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fabrication methods. 23.605 Section 23.605... Fabrication methods. (a) The methods of fabrication used must produce consistently sound structures. If a... fabrication method must be substantiated by a test program. [Doc. No. 4080, 29 FR 17955, Dec. 18, 1964; 30 FR...

Report of the fixed target heavy quark working group

International Nuclear Information System (INIS)

Appel, J.A.; Butler, J.N.; Christian, D.; Cooper, P.; Errede, D.; Garbincius, P.; Gourlay, S.; Guttierez, G.; James, C.; Kasper, P.; Kreymer, A.; Lach, J.; Murphy, T.; Rameika, G.; Speigel, L.; Summers, D.; Berger, E.; Bigi, I.; Busenitz, J.; Cox, B.; Cumalat, J.; Dunlea, J.; Thorndike, E.; Escobar, C.; Gouffon, P.; Kapoor, V.; Kaplan, D.M.; Knapp, B.; Wiencke, L.; Judd, D.; Wagonner, D.; Newsom, C.; Pedrini, D.; Potter, D.; Russ, J.; Purohit, M.; Selove, W.; Van Berg, R.; Shepard, P.; Yager, P.

1989-01-01

The status of Fixed Target experiments to study charm and bottom is reviewed. The physics motivation for further high statistics studies of charm and bottom is presented. The technical challenges which will be encountered in doing very high sensitivity studies are described, some possible solutions are offered, and areas where additional research and development are required and identified. 38 refs., 8 figs., 9 tabs

Fabrication of thin-wall, freestanding inertial confinement fusion targets by chemical vapor deposition

International Nuclear Information System (INIS)

Carroll, D.W.; McCreary, W.J.

1982-01-01

To meet the requirements for plasma physics experiments in the inertial confinement fusion (ICF) program, chemical vapor deposition (CVD) in fluid beds was used to fabricate freestanding tungsten spheres and cylinders with wall thicknesses less than 5.0 μm. Molybdenum and molybdenum alloy (TZM) mandrels of the desired geometry were suspended in a carrier bed of dense microspheres contained in an induction-heated fluid-bed reactor. The mandrels were free to float randomly through the bed, and using the reaction WF 6 +3H 2 →/sub /KW +6HF, very fine-grained tungsten was deposited onto the surface at a rate and in a grain size determined by temperature, gas flow rate, system pressure, and duration of the reaction. After coating, a portion of each mandrel was exposed by hole drilling or grinding. The mandrel was then removed by acid leaching, leaving a freestanding tungsten shape. Experimental procedures, mandrel preparation, and results obtained are discussed

Fabrication and Characterization of Targets for Shock Propagation and Radiation Burnthrough Measurements on Be-0.9 AT. % Cu Alloy

International Nuclear Information System (INIS)

Nobile, A.; Dropinski, S.C.; Edwards, J.M.; Rivera, G.; Margevicius, R.W.; Sebring, R.J.; Olson, R. E.; Tanner, D.L.

2004-01-01

Beryllium-copper alloy (Be0.9%Cu) ICF capsules are being developed for the pursuit of thermonuclear ignition at the National Ignition Facility (NIF). Success of this capsule material requires that its shock propagation and radiation burnthrough characteristics be accurately understood. To this end, experiments are being conducted to measure the shock propagation and radiation burnthrough properties of Be0.9%Cu alloy. These experiments involve measurements on small Be0.9%Cu wedge, step and flat samples. Samples are mounted on 1.6-mm-diameter x 1.2-mm-length hohlraums that are illuminated by the OMEGA laser at the University of Rochester. X-rays produced by the hohlraum drive the sample. A streaked optical pyrometer detects breakout of the shock produced by the X-ray pulse. In this paper we describe synthesis of the alloy material, fabrication and characterization of samples, and assembly of the targets. Samples were produced from Be0.9%Cu alloy that was synthesized by hot isostatic pressing of Be powder and copper flake. Samples were 850 μm diameter disks with varying thickness in the case of wedge and step samples, and uniform thickness in the case of flat samples. Sample thickness varied in the range 10-90 μm. Samples were prepared by precision lathe machining and electric discharge machining. The samples were characterized by a Veeco white light interferometer and an optical thickness measurement device that simultaneously measured the upper and lower surface contours of samples using two confocal laser probes. Several campaigns with these samples have been conducted over the past two years

Target Group Segmentation in the Horse Buyers' Market against the Background of Equestrian Experience.

Science.gov (United States)

Gille, Claudia; Kayser, Maike; Spiller, Achim

2010-01-01

Whereas in former times horses were reserved primarily for people involved in agriculture, elite equestrians or the military, nowadays equestrian sport has become an activity for people with a wide variety of backgrounds. However, as more and more people become involved with equestrian sport today, the knowledge concerning animal husbandry in general is diminishing due to an alienation from agricultural themes in modern societies. As a consequence, this development affects both riding ability and the appraisal of horses, especially with respect to the purchase of horses. In order to analyse which factors influence purchase decisions in the horse market in conjunction with equestrian experience, 739 horse riders were surveyed on their purchase behaviour in this study. Using cluster analysis, a typology was generated that provides a differentiated picture of the preferences of the various rider groups. Three clusters were distinguished: the "amateurs", the "experienced" and the "experts". Taking personal horse riding proficiency into account, it could be concluded that especially the "amateur" group required objective criteria for the evaluation of a horse they are considering purchasing. Alongside "measureable" qualities, such as previous showing success or the level of training of the horse, also other attributes such as the simple handling of the horse should be taken into consideration. As particularly the "amateur" group in equestrian sport is increasing in numbers, it is therefore advisable when preparing a horse for sale to align oneself to the needs of this customer segment in order to ensure an effective and targeted marketing of horses.

Target Group Segmentation in the Horse Buyers’ Market against the Background of Equestrian Experience

Science.gov (United States)

GILLE, Claudia; KAYSER, Maike; SPILLER, Achim

2011-01-01

Whereas in former times horses were reserved primarily for people involved in agriculture, elite equestrians or the military, nowadays equestrian sport has become an activity for people with a wide variety of backgrounds. However, as more and more people become involved with equestrian sport today, the knowledge concerning animal husbandry in general is diminishing due to an alienation from agricultural themes in modern societies. As a consequence, this development affects both riding ability and the appraisal of horses, especially with respect to the purchase of horses. In order to analyse which factors influence purchase decisions in the horse market in conjunction with equestrian experience, 739 horse riders were surveyed on their purchase behaviour in this study. Using cluster analysis, a typology was generated that provides a differentiated picture of the preferences of the various rider groups. Three clusters were distinguished: the “amateurs”, the “experienced” and the “experts”. Taking personal horse riding proficiency into account, it could be concluded that especially the “amateur” group required objective criteria for the evaluation of a horse they are considering purchasing. Alongside “measureable” qualities, such as previous showing success or the level of training of the horse, also other attributes such as the simple handling of the horse should be taken into consideration. As particularly the “amateur” group in equestrian sport is increasing in numbers, it is therefore advisable when preparing a horse for sale to align oneself to the needs of this customer segment in order to ensure an effective and targeted marketing of horses. PMID:24833979

Cylindrical fabric-confined soil structures

Science.gov (United States)

Harrison, Richard A.

A cylindrical fabric-soil structural concept for implementation on the moon and Mars which provides many advantages is proposed. The most efficient use of fabric is to fashion it into cylindrical tubes, creating cylindrical fabric-confined soil structures. The length, diameter, and curvature of the tubes will depend on the intended application. The cylindrical hoop forces provide radial confinement while end caps provide axial confinement. One of the ends is designed to allow passage of the soil into the fabric tube before sealing. Transportation requirements are reduced due to the low mass and volume of the fabric. Construction requirements are reduced due to the self-erection capability via the pneumatic exoskeleton. Maintenance requirements are reduced due to the passive nature of the concept. The structure's natural ductility is well suited for any seismic activity.

Safety and environmental advantages of using tritium-lean targets for inertial fusion

International Nuclear Information System (INIS)

Arzeni, S.; Latkowski, J. F.; Logan, B. G.; Meier, W. R.; Moir, R. W.; Perkins, L. J.; Sanz, J.

1999-01-01

While traditional inertial fusion energy target designs typically use equimolar portions of deuterium and tritium and have areal densities (ρr) of ∼ 3 g/cm 2 , significant safety and environmental (S and E) advantages may be obtained through the use of high-density (ρr ∼ 10 g/cm 2 ) targets with tritium components as low as 0.5%. Such targets would absorb much of the neutron energy within the target and could be self-sufficient from a tritium breeding point of view. Tritium self-sufficiency within the target would free target chamber designers from the need to use lithium-bearing blanket materials, while low inventories within each target would translate into low inventories in target fabrication facilities. Absorption of much of the neutron energy within the target, the extremely low tritium inventories, and the greatly moderated neutron spectrum, make ''tritium-lean'' targets appear quite attractive from an S and E perspective

Microfluidic Fabrication of Conjugated Polymer Sensor Fibers

Energy Technology Data Exchange (ETDEWEB)

Yoo, Imsung; Song, Simon [Hanyang University, Seoul (Korea, Republic of)

2014-10-15

We propose a fabrication method for polydiacetylene (PDA)-embedded hydrogel microfibers on a microfluidic chip. These fibers can be applied to the detection of cyclodextrines (CDs), which are a family of sugar and aluminum ions. PDA, a family of conjugated polymers, has unique characteristics when used for a sensor, because it undergoes a blue-to-red color transition and nonfluorescence-to-fluorescence transition in response to environmental stimulation. PDAs have different sensing characteristics depending on the head group of PCDA. By taking advantage of ionic crosslinking-induced hydrogel formation and the 3D hydrodynamic focusing effect on a microfluidic chip, PCDA-EDEA-derived diacetylene (DA) monomer-embedded microfibers were successfully fabricated. UV irradiation of the fibers afforded blue-colored PDA, and the resulting blue PDA fibers underwent a phase transition to red and emitted red fluorescence upon exposure to CDs and aluminum ions. Their fluorescence intensity varied depending on the CDs and aluminum ion concentrations. This phase transition was also observed when the fibers were dried.

Recent US target-physics-related research in heavy-ion inertial fusion: simulations for tamped targets and for disk experiments in accelerator test facilities

International Nuclear Information System (INIS)

Mark, J.W.K.

1982-01-01

Within the last few years, there have also appeared in the Heavy-Ion Fusion literature several studies of targets which have outer tampers. One-dimensional simulations indicate higher target gains with a judicious amount of tamping. But for these targets, a full investigation has not been carried through in regards to conservative criteria for fluid instabilities as well as reasonable imperfections in target fabrication and illumination symmetry which all affect target ignition and burn. Comparisons of these results with the gain survey of Part I would have to be performed with care. These calculations suggest that experiments relating to high temperature disk heating, as well as beam deposition, focusing and transport can be performed within the context of current design proposals for accelerator test-facilities. Since the test-facilities have lower ion kinetic energy and beam pulse power as compared to reactor drivers, we achieve high-beam intensities at the focal spot by using short focal distance and properly designed beam optics

Potassium-argon (argon-argon), structural fabrics

Science.gov (United States)

Cosca, Michael A.; Rink, W. Jack; Thompson, Jereon

2014-01-01

Definition: 40Ar/39Ar geochronology of structural fabrics: The application of 40Ar/39Ar methods to date development of structural fabrics in geologic samples. Introduction: Structural fabrics develop during rock deformation at variable pressures (P), temperatures (T), fluid compositions (X), and time (t). Structural fabrics are represented in rocks by features such as foliations and shear zones developed at the mm to km scale. In ideal cases, the P-T-X history of a given structural fabric can be constrained using stable isotope, cation exchange, and/or mineral equilibria thermobarometry (Essene 1989). The timing of structural fabric development can be assessed qualitatively using geologic field observations or quantitatively using isotope-based geochronology. High-precision geochronology of the thermal and fluid flow histories associated with structural fabric development can answer fundamental geologic questions including (1) when hydrothermal fluids transported and deposited ore minerals, ...

EIT-based fabric pressure sensing.

Science.gov (United States)

Yao, A; Yang, C L; Seo, J K; Soleimani, M

2013-01-01

This paper presents EIT-based fabric sensors that aim to provide a pressure mapping using the current carrying and voltage sensing electrodes attached to the boundary of the fabric patch. Pressure-induced shape change over the sensor area makes a change in the conductivity distribution which can be conveyed to the change of boundary current-voltage data. This boundary data is obtained through electrode measurements in EIT system. The corresponding inverse problem is to reconstruct the pressure and deformation map from the relationship between the applied current and the measured voltage on the fabric boundary. Taking advantage of EIT in providing dynamical images of conductivity changes due to pressure induced shape change, the pressure map can be estimated. In this paper, the EIT-based fabric sensor was presented for circular and rectangular sensor geometry. A stretch sensitive fabric was used in circular sensor with 16 electrodes and a pressure sensitive fabric was used in a rectangular sensor with 32 electrodes. A preliminary human test was carried out with the rectangular sensor for foot pressure mapping showing promising results.

EIT-Based Fabric Pressure Sensing

Directory of Open Access Journals (Sweden)

A. Yao

2013-01-01

Full Text Available This paper presents EIT-based fabric sensors that aim to provide a pressure mapping using the current carrying and voltage sensing electrodes attached to the boundary of the fabric patch. Pressure-induced shape change over the sensor area makes a change in the conductivity distribution which can be conveyed to the change of boundary current-voltage data. This boundary data is obtained through electrode measurements in EIT system. The corresponding inverse problem is to reconstruct the pressure and deformation map from the relationship between the applied current and the measured voltage on the fabric boundary. Taking advantage of EIT in providing dynamical images of conductivity changes due to pressure induced shape change, the pressure map can be estimated. In this paper, the EIT-based fabric sensor was presented for circular and rectangular sensor geometry. A stretch sensitive fabric was used in circular sensor with 16 electrodes and a pressure sensitive fabric was used in a rectangular sensor with 32 electrodes. A preliminary human test was carried out with the rectangular sensor for foot pressure mapping showing promising results.

Fabrication of hydroxyapatite thin films for biomedical applications using RF magnetron sputtering

International Nuclear Information System (INIS)

Yamaguchi, Tetsuro; Tanaka, Yoshikazu; Ide-Ektessabi, Ari

2006-01-01

The calcium phosphate thin films for medical applications require similar chemical properties as those of natural bone as well as a uniform surface without any defect, such as cracks and pinholes. In this study, the calcium phosphate thin films were fabricated using RF magnetron sputtering deposition technique at discharge power of 200W, 300W and 400W. The target used for the deposition was sintered HAp. RBS analysis showed that the Ca/P ratio increased with the discharge power becoming close to that of Ca/P=1.67 in ideal HAp. XPS analysis revealed the presence of PO 4 3- and OH - bonds in the calcium phosphate films fabricated. The chemical properties of the calcium phosphate thin films were similar to those of ideal HAp. The AFM results revealed that the thin films prepared had a uniform surface

Production of direct drive cylindrical targets for inertial confinement fusion experiments

International Nuclear Information System (INIS)

Elliott, N.E.; Day, R.D.; Hatch, D.J.; Sandoval, D.L.; Gomez, V.M.; Pierce, T.H.; Elliott, J.E.; Manzanares, R.

2002-01-01

We have made targets with cylindrical geometry for Inertial Confinement Fusion (ICF) experiments. These targets are used in hydrodynamic experiments on the OMEGA laser at the University of Rochester. The cylindrical design allows the study of three dimensional hydrodynamic effects in a pseudo 2D mode, simplifying data gathering and analysis. Direct drive refers to the fact that the target is illuminated directly by approximately 50 laser beams and is imploded by the material pressure generated from ablation of the outside of the target. The production of cylindrical targets involves numerous steps. These steps are shared in common with many other types of ICF targets but no other single target type encompasses such a wide range of fabrication techniques. These targets consist of a large number of individual parts, all fabricated from commercially purchased raw material, requiring many machining, assembly, electroplating and chemical process steps. Virtually every manufacturing and assembly process we currently possess is involved in the production of these targets. The generic target consists of a plastic cylinder (ablator) that is roughly lmm in diameter by 2.25mm long. The wall of the cylinder is roughly 0.07mm thick. There is an aluminum cylinder 0.5mm wide and O.Olmm thick centered on the inside of the plastic cylinder and coaxial with the outside plastic cylinder. The outside of this aluminum band has surface finishes of differing random average roughness. The required average surface roughness is determined in advance by experimental design based on the amount of turbulent mix to be observed. The interior of the cylinder is filled with low density polystyrene foam that is made in house. To produce a finished target additional features are added to each target. X-ray backlighters are cantilevered off the target that allow time resolved x-ray images of the imploding target to be recorded during the experiment. The x-ray backlighters are driven by additional

Manipulation of laser-accelerated proton beam profiles by nanostructured and microstructured targets

Directory of Open Access Journals (Sweden)

L. Giuffrida

2017-08-01

Full Text Available Nanostructured and microstructured thin foils have been fabricated and used experimentally as targets to manipulate the spatial profile of proton bunches accelerated through the interaction with high intensity laser pulses (6×10^{19}  W/cm^{2}. Monolayers of polystyrene nanospheres were placed on the rear surfaces of thin plastic targets to improve the spatial homogeneity of the accelerated proton beams. Moreover, thin targets with grating structures of various configurations on their rear sides were used to modify the proton beam divergence. Experimental results are presented, discussed, and supported by 3D particle-in-cell numerical simulations.

Public relations work through exhibitions. Getting in touch with the target groups. A case study by 'Informationskreis Kernenergie'

International Nuclear Information System (INIS)

Knapp, Sabine

1993-01-01

This presentation discusses the public relations work through exhibitions and fairs. Fairs and exhibitions provide an ideal opportunity to contact the target groups directly: political and economic opinion-makers; media representatives; insiders; young people and schoolchildren; interested public. During exhibitions the interested visitors are also supplied with extensive information material, mostly free of charge. An example the photo atlas 'Nuclear Energy in Germany' which we offered in an English edition as well and is attached to this presentation

Report of the collaboration project for research and development of sphere-pac fuel among JNC-PSI-NRG (1). Planning, fuel design, pin fabrication

International Nuclear Information System (INIS)

Morihira, Masayuki; Ozawa, Takayuki; Tomita, Yutaka; Suzuki, Masahiro; Kihara, Yoshiyuki; Shigetome, Yoshiaki; Kohno, Shusaku

2004-07-01

The collaboration project concerning sphere-pac fuel among JNC, Swiss PSI (Paul Scherrer Institut) and Dutch NRG (Nuclear Research and Consultancy Group) is in progress. Final target of the project is comparative irradiation tests of sphere-pac fuel in the HFR (High Flux Reactor) in Petten in the Netherlands with pellet type fuel and vipack fuel. Total 16 fuel segments (8 pins) of these three types of fuel are planned to be irradiated. Two sphere-pac fuel segments contain 5%Np in addition to 20%Pu-MOX. Other segments contain no Np. The objective of the irradiation tests is to obtain the restructuring data in the early beginning of life for SPF as well as power-to-melt test data for the potential study of SPF. At the same time introduction of modeling technique for irradiation performance analysis, fuel design, fuel fabrication is also important objective for JNC. Fabrication of irradiation test pins was completed till May 2003 in PSI. After transportation of the fuel pins to Petten, two times of irradiation were performed in January to March in 2004 and now post irradiation tests are in progress. Later two irradiations will be done till the autumn in 2004. This report summarized the basic plan, fuel design, and fabrication of irradiation test pins concerning this collaboration project. (author)

Qualitative Investigation of Some Locally Produced Printed Fabrics ...

African Journals Online (AJOL)

The results obtained showed that the locally produced fabrics exhibited comparably better end – use performance characteristics in terms of fabric weight per square meter, fabric flammability, and linear density. While the foreign fabrics are better in terms of Crease recovery, fabric handle, fabric sett, fabric shrinkage, and ...

Debating fabrication: 'Syrian Hero Boy' in the virtual public sphere

OpenAIRE

Storaas, Ingrid Hovda

2016-01-01

In November 2014, the film “Syrian hero boy” went viral. It depicted a young boy targeted by snipers. He dodges the bullets, and manages to save another child from the scene. After the story was published in newspapers worldwide, however, it became clear that it was a fabrication, shot and directed at a set in Malta. This thesis explores the media coverage of “Syrian hero boy” through a content analysis of 93 articles written about the film in online newspapers, asking how this coverage fit w...

Fabricating nuclear components

International Nuclear Information System (INIS)

Anon.

1977-01-01

Activities of the Nuclear Engineering Division of Vickers Ltd., particularly fabrication of long slim tubular components for power reactors and the construction of irradiation loops and rigs, are outlined. The processes include hydraulic forming for fabrication of various types of tubes and outer cases of fuel transfer buckets, various specialised welding operations including some applications of the TIG process, and induction brazing of specialised assemblies. (U.K.)

A smart multifunctional nanocomposite for intracellular targeted drug delivery and self-release

Science.gov (United States)

Wang, Chan; Lv, Piping; Wei, Wei; Tao, Shengyang; Hu, Tao; Yang, Jingbang; Meng, Changgong

2011-10-01

A multifunctional 'all-in-one' nanocomposite is fabricated using a colloid, template and surface-modification method. This material encompasses magnetic induced target delivery, cell uptake promotion and controlled drug release in one system. The nanocomposite is characterized by scanning electron microscopy, transmission electron microscopy, x-ray diffraction, N2 adsorption and vibrating sample magnetometry. The prepared material has a diameter of 350-400 nm, a high surface area of 420.29 m2 g - 1, a pore size of 1.91 nm and a saturation magnetization of 32 emu g - 1. Doxorubicin (DOX) is loaded in mesopores and acid-sensitive blockers are introduced onto the orifices of the mesopores by a Schiff base linker to implement pH-dependent self-release. Folate was also introduced to improve DOX targeted delivery and endocytosis. The linkers remained intact to block pores with ferrocene valves and inhibit the diffusion of DOX at neutral pH. However, in lysosomes of cancer cells, which have a weak acidic pH, hydrolysis of the Schiff base group removes the nanovalves and allows the trapped DOX to be released. These processes are demonstrated by UV-visible absorption spectra, confocal fluorescence microscopy images and methyl thiazolyl tetrazolium assays in vitro, which suggest that the smart nanocomposite successfully integrates targeted drug delivery with internal stimulus induced self-release and is a potentially useful material for nanobiomedicine.

A smart multifunctional nanocomposite for intracellular targeted drug delivery and self-release

International Nuclear Information System (INIS)

Wang Chan; Tao Shengyang; Hu Tao; Yang Jingbang; Meng Changgong; Lv Piping; Wei Wei

2011-01-01

A multifunctional 'all-in-one' nanocomposite is fabricated using a colloid, template and surface-modification method. This material encompasses magnetic induced target delivery, cell uptake promotion and controlled drug release in one system. The nanocomposite is characterized by scanning electron microscopy, transmission electron microscopy, x-ray diffraction, N 2 adsorption and vibrating sample magnetometry. The prepared material has a diameter of 350-400 nm, a high surface area of 420.29 m 2 g -1 , a pore size of 1.91 nm and a saturation magnetization of 32 emu g -1 . Doxorubicin (DOX) is loaded in mesopores and acid-sensitive blockers are introduced onto the orifices of the mesopores by a Schiff base linker to implement pH-dependent self-release. Folate was also introduced to improve DOX targeted delivery and endocytosis. The linkers remained intact to block pores with ferrocene valves and inhibit the diffusion of DOX at neutral pH. However, in lysosomes of cancer cells, which have a weak acidic pH, hydrolysis of the Schiff base group removes the nanovalves and allows the trapped DOX to be released. These processes are demonstrated by UV-visible absorption spectra, confocal fluorescence microscopy images and methyl thiazolyl tetrazolium assays in vitro, which suggest that the smart nanocomposite successfully integrates targeted drug delivery with internal stimulus induced self-release and is a potentially useful material for nanobiomedicine.

DRAPING SIMULATION OF WOVEN FABRICS

Energy Technology Data Exchange (ETDEWEB)

Rodgers, William [General Motors LLC; Jin, Xiaoshi [ESI Group NA; Zhu, Jiang [Optimal CAE; Wathen, Terrence [General Motors LLC; Doroudian2, Mark [ESI Group NA; Aitharaju, Venkat [General Motors LLC

2016-09-07

Woven fabric composites are extensively used in molding complex geometrical shapes due to their high conformability compared to other fabrics. Preforming is an important step in the overall process, where the two-dimensional fabric is draped to become the three-dimensional shape of the part prior to resin injection. During preforming, the orientation of the yarns may change significantly compared to the initial orientations. Accurate prediction of the yarn orientations after molding is important for evaluating the structural performance of the final part. This paper presents a systematic investigation of the angle changes during the preform operation for carbon fiber twill and satin weave fabrics. Preforming experiments were conducted using a truncated pyramid mold geometry designed and fabricated at the General Motors Research Laboratories. Predicted results for the yarn orientations were compared with experimental results and good agreement was observed

Dual purpose laser ablation-inductively coupled plasma mass spectrometry for pulsed laser deposition and diagnostics of thin film fabrication: preliminary study.

Science.gov (United States)

Azdejković, Mersida Janeva; van Elteren, Johannes Teun; Rozman, Kristina Zuzek; Jaćimović, Radojko; Sarantopoulou, Evangelia; Kobe, Spomenka; Cefalas, Alkiviadis Constantinos

2009-08-15

PLD (pulsed laser deposition) is an attractive technique to fabricate thin films with a stoichiometry reflecting that of the target material. Conventional PLD instruments are more or less black boxes in which PLD is performed virtually "blind", i.e. without having great control on the important PLD parameters. In this preliminary study, for the first time, a 213 nm Nd-YAG commercial laser ablation-inductively coupled plasma mass spectrometer (LA-ICPMS) intended for microanalysis work was used for PLD under atmospheric pressure and in and ex situ ICPMS analysis for diagnostics of the thin film fabrication process. A PLD demonstration experiment in a He atmosphere was performed with a Sm(13.8)Fe(82.2)Ta(4.0) target-Ta-coated silicon wafer substrate (contraption with defined geometry in the laser ablation chamber) to transfer the permanent magnetic properties of the target to the film. Although this paper is not dealing with the magnetic properties of the film, elemental analysis was applied as a means of depicting the PLD process. It was shown that in situ ICPMS monitoring of the ablation plume as a function of the laser fluence, beam diameter and repetition rate may be used to ensure the absence of large particles (normally having a stoichiometry somewhat different from the target). Furthermore, ex situ microanalysis of the deposited particles on the substrate, using the LA-ICPMS as an elemental mapping tool, allowed for the investigation of PLD parameters critical in the fabrication of a thin film with appropriate density, homogeneity and stoichiometry.

Comparison the Marginal and Internal Fit of Metal Copings Cast from Wax Patterns Fabricated by CAD/CAM and Conventional Wax up Techniques

Science.gov (United States)

Vojdani, M; Torabi, K; Farjood, E; Khaledi, AAR

2013-01-01

Statement of Problem: Metal-ceramic crowns are most commonly used as the complete coverage restorations in clinical daily use. Disadvantages of conventional hand-made wax-patterns introduce some alternative ways by means of CAD/CAM technologies. Purpose: This study compares the marginal and internal fit of copings cast from CAD/CAM and conventional fabricated wax-patterns. Materials and Method: Twenty-four standardized brass dies were prepared and randomly divided into 2 groups according to the wax-patterns fabrication method (CAD/CAM technique and conventional method) (n=12). All the wax-patterns were fabricated in a standard fashion by means of contour, thickness and internal relief (M1-M12: representative of CAD/CAM group, C1-C12: representative of conventional group). CAD/CAM milling machine (Cori TEC 340i; imes-icore GmbH, Eiterfeld, Germany) was used to fabricate the CAD/CAM group wax-patterns. The copings cast from 24 wax-patterns were cemented to the corresponding dies. For all the coping-die assemblies cross-sectional technique was used to evaluate the marginal and internal fit at 15 points. The Student’s t- test was used for statistical analysis (α=0.05). Results: The overall mean (SD) for absolute marginal discrepancy (AMD) was 254.46 (25.10) um for CAD/CAM group and 88.08(10.67) um for conventional group (control). The overall mean of internal gap total (IGT) was 110.77(5.92) um for CAD/CAM group and 76.90 (10.17) um for conventional group. The Student’s t-test revealed significant differences between 2 groups. Marginal and internal gaps were found to be significantly higher at all measured areas in CAD/CAM group than conventional group (pmarginal and internal fit than CAD/CAM (machine-milled) technique. All the factors for 2 groups were standardized except wax pattern fabrication technique, therefore, only the conventional group results in copings with clinically acceptable margins of less than 120um. PMID:24724133

A sensitive DNA biosensor fabricated from gold nanoparticles, carbon nanotubes, and zinc oxide nanowires on a glassy carbon electrode

International Nuclear Information System (INIS)

Wang Jie; Li Shuping; Zhang Yuzhong

2010-01-01

We outline here the fabrication of a sensitive electrochemical DNA biosensor for the detection of sequence-specific target DNA. Zinc oxide nanowires (ZnONWs) were first immobilized on the surface of a glassy carbon electrode. Multi-walled carbon nanotubes (MWCNTs) with carboxyl groups were then dropped onto the surface of the ZnONWs. Gold nanoparticles (AuNPs) were subsequently introduced to the surface of the MWNTs/ZnONWs by electrochemical deposition. A single-stranded DNA probe with a thiol group at the end (HS-ssDNA) was covalently immobilized on the surface of the AuNPs by forming an Au-S bond. Scanning electron microscopy (SEM) and cyclic voltammetry (CV) were used to investigate the film assembly process. Differential pulse voltammetry (DPV) was used to monitor DNA hybridization by measuring the electrochemical signals of [Ru(NH 3 ) 6 ] 3+ bounding to double-stranded DNA (dsDNA). The incorporation of ZnONWs and MWCNTs in this sensor design significantly enhances the sensitivity and the selectivity. This DNA biosensor can detect the target DNA quantitatively in the range of 1.0 x 10 -13 to 1.0 x 10 -7 M, with a detection limit of 3.5 x 10 -14 M (S/N = 3). In addition, the DNA biosensor exhibits excellent selectivity, even for single-mismatched DNA detection.

Single older women who applied for the giving life more lustre course : Are they the target group that was aimed for?

NARCIS (Netherlands)

Kremers, Ismay; Steverink, Nardi; Albersnagel, Frans A.; Slaets, Joris P. J.

2007-01-01

The present study investigated whether the women who applied for the self-management of well-being course Giving life more LUSTRE can be considered the target group that was intended. By comparing the course applicants with a random sample of community dwelling single women, it was found that, as

Fabrication of piezoresistive microcantilever using surface micromachining technique for biosensors

Energy Technology Data Exchange (ETDEWEB)

Na, Kwang-Ho [Department of Electrical Engineering and Nano-Bio Research Center, Myongji University, Yongin, Gyeonggido 449-728 (Korea, Republic of); Kim, Yong-Sang [Department of Electrical Engineering and Nano-Bio Research Center, Myongji University, Yongin, Gyeonggido 449-728 (Korea, Republic of); Kang, C.J. [Department of Physics and Nano-Bio Research Center, Myongji University, San38-2 Namdong, Yongin, Gyeonggido 449-728 (Korea, Republic of)]. E-mail: cjkang@mju.ac.kr

2005-11-15

A microcantilever-based biosensor with piezoresistor has been fabricated using surface micromachining technique, which is cost effective and simplifies a fabrication procedure. In order to evaluate the characteristics of the cantilever, the cystamine terminated with thiol was covalently immobilized on the gold-coated side of the cantilever and glutaraldehyde that would be bonded with amine group in the cystamine was injected subsequently. This process was characterized by measuring the deflection of the cantilever in real time monitoring. Using a piezoresistive read-out and a well-known optical beam deflection method as well, the measurement of deflection was carried out. The sensitivity of piezoresistive method is good enough compared with that of optical beam deflection method.

Fabrication of Copper-Rich Cu-Al Alloy Using the Wire-Arc Additive Manufacturing Process

Science.gov (United States)

Dong, Bosheng; Pan, Zengxi; Shen, Chen; Ma, Yan; Li, Huijun

2017-12-01

An innovative wire-arc additive manufacturing (WAAM) process is used to fabricate Cu-9 at. pct Al on pure copper plates in situ, through separate feeding of pure Cu and Al wires into a molten pool, which is generated by the gas tungsten arc welding (GTAW) process. After overcoming several processing problems, such as opening the deposition molten pool on the extremely high-thermal conductive copper plate and conducting the Al wire into the molten pool with low feed speed, the copper-rich Cu-Al alloy was successfully produced with constant predesigned Al content above the dilution-affected area. Also, in order to homogenize the as-fabricated material and improve the mechanical properties, two further homogenization heat treatments at 1073 K (800 °C) and 1173 K (900 °C) were applied. The material and mechanical properties of as-fabricated and heat-treated samples were compared and analyzed in detail. With increased annealing temperatures, the content of precipitate phases decreased and the samples showed gradual improvements in both strength and ductility with little variation in microstructures. The present research opened a gate for in-situ fabrication of Cu-Al alloy with target chemical composition and full density using the additive manufacturing process.

Triazatriangulene as binding group for molecular electronics

DEFF Research Database (Denmark)

Wei, Zhongming; Wang, Xintai; Borges, Anders

2014-01-01

The triazatriangulene (TATA) ring system was investigated as a binding group for tunnel junctions of molecular wires on gold surfaces. Self-assembled monolayers (SAMs) of TATA platforms with three different lengths of phenylene wires were fabricated, and their electrical conductance was recorded ...... with its high stability and directionality make this binding group very attractive for molecular electronic measurements and devices. (Figure Presented)....

Preparation of activated carbon fabrics from cotton fabric precursor

Science.gov (United States)

Salehi, R.; Dadashian, F.; Abedi, M.

2017-10-01

The preparation of activated carbon fabrics (ACFs) from cotton fabric was performed by chemical activation with phosphoric acid (H3PO4). The operation conditions for obtaining the ACFs with the highest the adsorption capacity and process yield, proposed. Optimized conditions were: impregnation ratio of 2, the rate of temperature rising of 7.5 °C min-1, the activation temperature of 500 °C and the activation time of 30 min. The ACFs produced under optimized conditions was characterized by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). The surface area and pore volume of carbon nanostructures was characterized by BET nitrogen adsorption isotherm at 77 °K. The pore size distribution calculated from the desorption branch according to BJH method. The iodine number of the prepared ACFs was determined by titration at 30 °C based on the ASTM D4607-94. The results showed the improvement of porous structure, fabric shape, surface area (690 m2/g), total pore volume (0.3216 cm3/g), and well-preserved fibers integrity.

Facile preparation of super-hydrophilic poly(ethylene terephthalate) fabric using dilute sulfuric acid under microwave irradiation

Energy Technology Data Exchange (ETDEWEB)

Xu, Fang [College of Textiles and Garments, Southwest University, Chongqing 400715 (China); Chongqing Engineering Research Center of Biomaterial Fiber and Modern Textile, Chongqing 400715 (China); Zhang, Guangxian, E-mail: zgx656472@sina.com.cn [College of Textiles and Garments, Southwest University, Chongqing 400715 (China); Chongqing Engineering Research Center of Biomaterial Fiber and Modern Textile, Chongqing 400715 (China); Zhang, Fengxiu [College of Chemistry and Chemical Engineering, Southwest University, Chongqing 400715 (China); Zhang, Yuansong [College of Textiles and Garments, Southwest University, Chongqing 400715 (China); Chongqing Engineering Research Center of Biomaterial Fiber and Modern Textile, Chongqing 400715 (China)

2015-09-15

Highlights: • A durable super-hydrophilic PET fabric was prepared using dilute H{sub 2}SO{sub 4} under microwave irradiation. • Dilute sulfuric acid was gradually concentrated enough to sulfonate PET fabric. • Microwave irradiation made PET fabric modification highly efficient. • The mechanical properties of modified PET fibers were kept well. • The method was novel, rapid, and eco-friendly. - Abstract: The hydrophilicity of a poly(ethylene terephthalate) (PET) fabric was greatly modified by using dilute sulfuric acid, which gradually became concentrated enough to sulfonate the fabric when microwave irradiation (MW) was applied. The modified PET fabric was super-hydrophilic. Modifying the fabric caused the water contact angle to decrease from 132.46 (for the unmodified fabric) to 0°, the water absorption rate to increase from 36.45 to 119.78%, and the capillary rise height to increase from 0.4 to 14.4 cm. The hydrophilicity of the modified PET fabric was not affected by washing it many times. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy analyses showed that there were sulfonic acid groups on the modified fibers. Almost no difference between the surfaces of the unmodified and modified PET fibers was found using scanning electron microscopy. Analysis by differential scanning calorimetry showed that the unmodified and modified fabrics had similar thermostabilities. X-ray diffraction analysis of the crystalline structures of the unmodified and modified fibers showed that they were almost the same. The strength, elasticity, and rigidity of the unmodified fabric were retained by the modified fabric. The modified fabric had better dyeing properties than the unmodified fabric.

Micro-fabricated all optical pressure sensors

DEFF Research Database (Denmark)

Havreland, Andreas Spandet; Petersen, Søren Dahl; Østergaard, Christian

2017-01-01

Optical pressure sensors can operate in certain harsh application areas where the electrical pressure sensors cannot. However, the sensitivity is often not as good for the optical sensors. This work presents an all optical pressure sensor, which is fabricated by micro fabrication techniques, where...... the sensitivity can be tuned in the fabrication process. The developed sensor design, simplifies the fabrication process leading to a lower fabrication cost, which can make the all optical pressure sensors more competitive towards their electrical counterpart. The sensor has shown promising results and a linear...... pressure response has been measured with a sensitivity of 0.6nm/bar....

Fabrication of malleable three-dimensional-printed customized bolus using three-dimensional scanner.

Directory of Open Access Journals (Sweden)

Jae Won Park

Full Text Available A three-dimensional (3D-printed customized bolus (3D bolus can be used for radiotherapy application to irregular surfaces. However, bolus fabrication based on computed tomography (CT scans is complicated and also delivers unwanted irradiation. Consequently, we fabricated a bolus using a 3D scanner and evaluated its efficacy. The head of an Alderson Rando phantom was scanned with a 3D scanner. The 3D surface data were exported and reconstructed with Geomagic Design X software. A 3D bolus of 5-mm thickness designed to fit onto the nose was printed with the use of rubber-like printing material, and a radiotherapy plan was developed. We successfully fabricated the customized 3D bolus, and further, a CT simulation indicated an acceptable fit of the 3D bolus to the nose. There was no air gap between the bolus and the phantom surface. The percent depth dose (PDD curve of the phantom with the 3D bolus showed an enhanced surface dose when compared with that of the phantom without the bolus. The PDD of the 3D bolus was comparable with that of a commercial superflab bolus. The radiotherapy plan considering the 3D bolus showed improved target coverage when compared with that without the bolus. Thus, we successfully fabricated a customized 3D bolus for an irregular surface using a 3D scanner instead of a CT scanner.

Fabrication of metal-matrix composites and adaptive composites using ultrasonic consolidation process

International Nuclear Information System (INIS)

Kong, C.Y.; Soar, R.C.

2005-01-01

Ultrasonic consolidation (UC) has been used to embed thermally sensitive and damage intolerant fibres within aluminium matrix structures using high frequency, low amplitude, mechanical vibrations. The UC process can induce plastic flow in the metal foils being bonded, to allow the embedding of fibres at typically 25% of the melting temperature of the base metal and at a fraction of the clamping force when compared to fusion processes. To date, the UC process has successfully embedded Sigma silicon carbide (SiC) fibres, shape memory alloy wires and optical fibres, which are presented in this paper. The eventual aim of this research is targeted at the fabrication of adaptive composite structures having the ability to measure external stimuli and respond by adapting their structure accordingly, through the action of embedded active and passive functional fibres within a freeform fabricated metal-matrix structure. This paper presents the fundamental studies of this research to identify embedding methods and working range for the fabrication of adaptive composite structures. The methods considered have produced embedded fibre specimens in which large amounts of plastic flow have been observed, within the matrix, as it is deformed around the fibres, resulting in fully consolidated specimens without damage to the fibres. The microscopic observation techniques and macroscopic functionality tests confirms that the UC process could be applied to the fabrication of metal-matrix composites and adaptive composites, where fusion techniques are not feasible and where a 'cold' process is necessary