Influence of polymeric subcoats on the drug release properties of tablets powder-coated with pre-plasticized Eudragit L 100-55.

Science.gov (United States)

Sauer, Dorothea; Watts, Alan B; Coots, Lonique B; Zheng, Weijia C; McGinity, James W

2009-02-09

The aim of the study was to investigate the properties of sodium valproate tablets that were dry powder-coated with pre-plasticized Eudragit L 100-55. Polyethylene glycol 3350 (PEG 3350) was used as primer to facilitate initial coating powder adhesion. Solubility parameters were employed to determine the wetting properties of the PEG 3350 primer. Additional PEG 3350 within the powder coating formulation was required to enable powder adhesion to the tablet cores. The application of a subcoat of either Eudragit E PO or Eudragit RL PO facilitated adhesion of the enteric polymer to the tablet cores and reduced the amount PEG 3350 required in the coating formulation. Since reduction of the PEG 3350 content produced less water-vapor permeable films, the enteric coating level necessary to control the drug release was decreased. PEG 3350 and Methocel K4M were incorporated in both Eudragit E PO and Eudragit RL PO subcoating formulations as pore forming agents. The influence of the pore forming excipients on physicochemical properties of free powder-cast films was investigated. The miscibility of the PEG 3350 and Methocel K4M in the film coating was correlated with their ability to function as pore forming agent.

Multispectral UV Imaging for Determination of the Tablet Coating Thickness.

Science.gov (United States)

Novikova, Anna; Carstensen, Jens M; Zeitler, J Axel; Rades, Thomas; Leopold, Claudia S

2017-06-01

The applicability of off-line multispectral UV imaging in combination with multivariate data analysis was investigated to determine the coating thickness and its distribution on the tablet surface during lab-scale coating. The UV imaging results were compared with the weight gain measured for each individual tablet and the corresponding coating thickness and its distribution measured by terahertz pulsed imaging (TPI). Three different tablet formulations were investigated, 2 of which contained UV-active tablet cores. Three coating formulations were applied: Aquacoat® ECD (a mainly translucent coating) and Eudragit® NE (a turbid coating containing solid particles). It was shown that UV imaging is a fast and nondestructive method to predict individual tablet weight gain as well as coating thickness. The coating thickness distribution profiles determined by UV imaging correlated to the results of the TPI measurements. UV imaging appears to hold a significant potential as a process analytical technology tool for determination of the tablet coating thickness and its distribution resulting from its high measurement speed, high molar absorptivity, and a high scattering coefficient, in addition to relatively low costs. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Tablet coating by injection molding technology - Optimization of coating formulation attributes and coating process parameters.

Science.gov (United States)

Desai, Parind M; Puri, Vibha; Brancazio, David; Halkude, Bhakti S; Hartman, Jeremy E; Wahane, Aniket V; Martinez, Alexander R; Jensen, Keith D; Harinath, Eranda; Braatz, Richard D; Chun, Jung-Hoon; Trout, Bernhardt L

2018-01-01

We developed and evaluated a solvent-free injection molding (IM) coating technology that could be suitable for continuous manufacturing via incorporation with IM tableting. Coating formulations (coating polymers and plasticizers) were prepared using hot-melt extrusion and screened via stress-strain analysis employing a universal testing machine. Selected coating formulations were studied for their melt flow characteristics. Tablets were coated using a vertical injection molding unit. Process parameters like softening temperature, injection pressure, and cooling temperature played a very important role in IM coating processing. IM coating employing polyethylene oxide (PEO) based formulations required sufficient room humidity (>30% RH) to avoid immediate cracks, whereas other formulations were insensitive to the room humidity. Tested formulations based on Eudrajit E PO and Kollicoat IR had unsuitable mechanical properties. Three coating formulations based on hydroxypropyl pea starch, PEO 1,000,000 and Opadry had favorable mechanical (35% elongation, >95×10 4 J/m 3 toughness) and melt flow (>0.4g/min) characteristics, that rendered acceptable IM coats. These three formulations increased the dissolution time by 10, 15 and 35min, respectively (75% drug release), compared to the uncoated tablets (15min). Coated tablets stored in several environmental conditions remained stable to cracking for the evaluated 8-week time period. Copyright © 2017 Elsevier B.V. All rights reserved.

ESR accident dosimetry using medicine tablets coated with sugar

International Nuclear Information System (INIS)

Kai, A.; Miki, T.; Ikeya, M.

1990-01-01

Properties of radiation-induced radicals in medicine tablets were investigated using electron spin resonance (ESR). A sharp ESR signal sensitive to gamma ray irradiation was observed in the sugar coating part of the tablets. The signal has anisotropic g values of g 1 = 2.0009, g 2 = 2.0007 and g 3 = 2.0002. The signal grows linearly with dose at least up to about 20 Gy. No fading was observed at room temperature even when exposed to sunlight. The dose to artificially irradiated tablets was estimated using the signal intensity and a previously determined calibration curve. The signal in sugar coated tablets can be utilised for dose measurements. In particular, the wide distribution of sugar coated tablets allows the use of the tablets as accident dosemeters. (author)

Effect of protective coating of aspirin tablets with acrylatemethacrylate copolymers on tablet disintegration times and dissolution rates

OpenAIRE

Okor R; Eichie F; Uhumwangho M; Aka-Aha A

2007-01-01

Tablets of aspirin (a moisture degradable drug) have been film coated with two analogous Eudragit RL and RS copolymers designated here as A and B which differ only in their cation content in the ratio 2:1 (A:B). A, is therefore more hydrophilic than B. The tablets were film coated with ethanol solutions of these two polymers. Film coating with either A or B significantly reduced the moisture uptake potentials of the tablets but caused an increase in the disintegration times of the tablets and...

Development of enteric coated tablets from spray dried extract of feverfew (Tanacetum parthenium L:

Directory of Open Access Journals (Sweden)

Juliana Siqueira Chaves

2009-09-01

Full Text Available Tanacetum parthenium (feverfew is an herb that is commercialized worldwide as a therapeutic treatment for migraine. Its pharmacological effect is mainly due to the presence of the sesquiterpene lactone parthenolide as well as of flavonoids. So far, there are no studies on standardization of pre-formulations or phytomedicines containing this herb. The present study aimed at developing a pre-formulation using a standardized spray-dried extract of feverfew and further designing and standardizing enteric coated tablets. In this work, the spray-dried extract of feverfew was evaluated for its parthenolide, santin and total flavonoid content, parthenolide solubility, particle size, tapped density, hygroscopicity, angle of repose and moisture content. Tablets containing the spray-dried extract were tested for their average weight, friability, hardness, and disintegration time. The total flavonoid and parthenolide contents in the spray-dried extract were 1.31 % and 0.76% w/w, respectively. The spray-dried extract presented consistent pharmacotechnical properties and allowed its tableting by direct compression. Tablet properties were in accordance with the proposed specifications. The procedures described herein can be used to prepare and evaluate pre-formulations of feverfew with adequate properties for the development of a high-quality phytomedicine.Tanacetum parthenium (tanaceto é uma planta medicinal comercializada no mundo todo para tratamento de enxaqueca. Seu efeito farmacológico é creditado principalmente à lactona sesquiterpênica partenolídeo e flavonóides. Até o momento não existem estudos sobre a padronização de pré-formulações ou o desenvolvimento de fitoterápicos com tanaceto. Logo, o objetivo deste trabalho foi obter comprimidos de revestimento entérico a partir de extrato seco e padronizado de tanaceto. Neste trabalho, o extrato seco do tanaceto obtido pelo método de spray drying foi avaliado quanto ao teor de partenol

Correlating bilayer tablet delamination tendencies to micro-environmental thermodynamic conditions during pan coating.

Science.gov (United States)

Zacour, Brian M; Pandey, Preetanshu; Subramanian, Ganeshkumar; Gao, Julia Z; Nikfar, Faranak

2014-06-01

The objective of this study was to determine the impact that the micro-environment, as measured by PyroButton data loggers, experienced by tablets during the pan coating unit operation had on the layer adhesion of bilayer tablets in open storage conditions. A full factorial design of experiments (DOE) with three center points was conducted to study the impact of final tablet hardness, film coating spray rate and film coating exhaust temperature on the delamination tendencies of bilayer tablets. PyroButton data loggers were placed (fixed) at various locations in a pan coater and were also allowed to freely move with the tablet bed to measure the micro-environmental temperature and humidity conditions of the tablet bed. The variance in the measured micro-environment via PyroButton data loggers accounted for 75% of the variance in the delamination tendencies of bilayer tablets on storage (R(2 )= 0.75). A survival analysis suggested that tablet hardness and coating spray rate significantly impacted the delamination tendencies of the bilayer tablets under open storage conditions. The coating exhaust temperature did not show good correlation with the tablets' propensity to crack indicating that it was not representative of the coating micro-environment. Models created using data obtained from the PyroButton data loggers outperformed models created using primary DOE factors in the prediction of bilayer tablet strength, especially upon equipment or scale transfers. The coating micro-environment experienced by tablets during the pan coating unit operation significantly impacts the strength of the bilayer interface of tablets on storage.

Formulation and process strategies to minimize coat damage for compaction of coated pellets in a rotary tablet press: A mechanistic view.

Science.gov (United States)

Xu, Min; Heng, Paul Wan Sia; Liew, Celine Valeria

2016-02-29

Compaction of multiple-unit pellet system (MUPS) tablets has been extensively studied in the past few decades but with marginal success. This study aims to investigate the formulation and process strategies for minimizing pellet coat damage caused by compaction and elucidate the mechanism of damage sustained during the preparation of MUPS tablets in a rotary tablet press. Blends containing ethylcellulose-coated pellets and cushioning agent (spray dried aggregates of micronized lactose and mannitol), were compacted into MUPS tablets in a rotary tablet press. The effects of compaction pressure and dwell time on the physicomechanical properties of resultant MUPS tablets and extent of pellet coat damage were systematically examined. The coated pellets from various locations at the axial and radial peripheral surfaces and core of the MUPS tablets were excavated and assessed for their coat damage individually. Interestingly, for a MUPS tablet formulation which consolidates by plastic deformation, the tablet mechanical strength could be enhanced without exacerbating pellet coat damage by extending the dwell time in the compaction cycle during rotary tableting. However, the increase in compaction pressure led to faster drug release rate. The location of the coated pellets in the MUPS tablet also contributed to the extent of their coat damage, possibly due to uneven force distribution within the compact. To ensure viability of pellet coat integrity, the formation of a continuous percolating network of cushioning agent is critical and the applied compaction pressure should be less than the pellet crushing strength. Copyright © 2015 Elsevier B.V. All rights reserved.

Characterization of the coating and tablet core roughness by means of 3D optical coherence tomography.

Science.gov (United States)

Markl, Daniel; Wahl, Patrick; Pichler, Heinz; Sacher, Stephan; Khinast, Johannes G

2018-01-30

This study demonstrates the use of optical coherence tomography (OCT) to simultaneously characterize the roughness of the tablet core and coating of pharmaceutical tablets. OCT is a high resolution non-destructive and contactless imaging methodology to characterize structural properties of solid dosage forms. Besides measuring the coating thickness, it also facilitates the analysis of the tablet core and coating roughness. An automated data evaluation algorithm extracts information about coating thickness, as well as tablet core and coating roughness. Samples removed periodically from a pan coating process were investigated, on the basis of thickness and profile maps of the tablet core and coating computed from about 480,000 depth measurements (i.e., 3D data) per sample. This data enables the calculation of the root mean square deviation, the skewness and the kurtosis of the assessed profiles. Analyzing these roughness parameters revealed that, for the given coating formulation, small valleys in the tablet core are filled with coating, whereas coarse features of the tablet core are still visible on the final film-coated tablet. Moreover, the impact of the tablet core roughness on the coating thickness is analyzed by correlating the tablet core profile and the coating thickness map. The presented measurement method and processing could be in the future transferred to in-line OCT measurements, to investigate core and coating roughness during the production of film-coated tablets. Copyright © 2017. Published by Elsevier B.V.

Biomaterial-Derived Calcium Carbonate Nanoparticles for Enteric Drug Delivery

Directory of Open Access Journals (Sweden)

Diane Render

2016-01-01

Full Text Available Oral drug delivery systems provide the most convenient, noninvasive, readily acceptable alternatives to parenteral systems. In the current work, eggshell-derived calcium carbonate (CaCO3 nanoparticles were used to develop enteric drug delivery system in the form of tablets. CaCO3 nanoparticles were manufactured using top-down ball-milling method and characterized by X-ray diffractometry (XRD and transmission electron microscopy (TEM and loaded with 5-fluorouracil as a model drug. Tablets with varying CaCO3 core and binder compositions were fabricated and coated with Eudragit S100 or Eudragit L100. Suitability for enteric delivery of the tablets was tested by oral administration to rabbits and radiography. Radiograph images showed that the tablet remained in the stomach of the rabbit for up to 3 hours. Further modifications of these biomaterial-derived nanoparticles and the coatings will enable manufacturing of stable formulations for slow or controlled release of pharmaceuticals for enteric delivery.

Optimasi Formula Tablet Salut Enterik Natrium Diklofenak dengan Bahan Penyalut Kollicoat 30 D

Directory of Open Access Journals (Sweden)

Nanang Yunarto

2015-05-01

Full Text Available Diclofenac sodium is an analgetic and antiinflammation drug and commonly used by oral administration. Because of it’s side effects that can cause stomach irritation, nausea and vomiting, it’s made in the form of enteric-coated. Enteric-coated formulations developed used organic solvent having toxicity and flammability risks. The aim of this study is to develop diclofenac sodium enteric-coated tablets with a water-based coating material. Coating material used is Kollicoat 30 D which is a derivative of acrylic polymer that can dispersed in water. Optimalization of the formula is done by the weight gain 4%, 6% and 8%. The result showed that enteric coated tablets used coating material with weight gain 8% gave the best result with all parameters meet the requirements of the test, there was no change in acid medium for 2 hours and stable released active ingredient

Two Contrasting Failure Modes of Enteric Coated Beads.

Science.gov (United States)

Shi, Galen H; Dong, Xia; Lytle, Michelle; Kemp, Craig A J; Behme, Robert J; Hinds, Jeremy; Xiao, Zhicheng

2018-04-09

This study aimed to elucidate the mechanisms and kinetics of coating failure for enteric coated beads exposed to high-humidity conditions at different storage temperatures. Enteric coated beads were placed on high-humidity conditions (75 to 98% relative humidity (RH)) in the temperature range of 5 to 40°C. These stability samples of beads were tested for acid dissolution and water activity and also analyzed with SEM, X-ray CT, and DMA. Exposure of enteric coated beads to high humidity led to increased gastric release of drug which eventually failed the dissolution specification. SEM showed visible cracks on the surface of beads exposed to 5°C/high humidity and fusion of enteric beads into agglomerates at 40°C/high humidity. In a non-destructive time elapse study, X-ray CT demonstrated swelling of microcrystalline cellulose cores, crack initiation, and propagation through the API layer within days under 5°C/98% RH storage conditions and ultimately fracture through the enteric coating. DMA data showed a marked reduction in T g of the enteric coating materials after exposure to humidity. At 5°C/high humidity, the hygroscopic microcrystalline cellulose core absorbed moisture leading to core swelling and consequent fracture through the brittle API and enteric layers. At 40°C (high humidity) which is above the T g of the enteric polymer, enteric coated beads coalesced into agglomerates due to melt flow of the enteric coating. We believe it is the first report on two distinct failure models of enteric coated dosage forms.

Development and evaluation of a dimensionless mechanistic pan coating model for the prediction of coated tablet appearance.

Science.gov (United States)

Niblett, Daniel; Porter, Stuart; Reynolds, Gavin; Morgan, Tomos; Greenamoyer, Jennifer; Hach, Ronald; Sido, Stephanie; Karan, Kapish; Gabbott, Ian

2017-08-07

A mathematical, mechanistic tablet film-coating model has been developed for pharmaceutical pan coating systems based on the mechanisms of atomisation, tablet bed movement and droplet drying with the main purpose of predicting tablet appearance quality. Two dimensionless quantities were used to characterise the product properties and operating parameters: the dimensionless Spray Flux (relating to area coverage of the spray droplets) and the Niblett Number (relating to the time available for drying of coating droplets). The Niblett Number is the ratio between the time a droplet needs to dry under given thermodynamic conditions and the time available for the droplet while on the surface of the tablet bed. The time available for drying on the tablet bed surface is critical for appearance quality. These two dimensionless quantities were used to select process parameters for a set of 22 coating experiments, performed over a wide range of multivariate process parameters. The dimensionless Regime Map created can be used to visualise the effect of interacting process parameters on overall tablet appearance quality and defects such as picking and logo bridging. Copyright © 2017 Elsevier B.V. All rights reserved.

Pharmacokinetic Study of a Diclofenac Sodium Capsule Filled with Enteric-coated Pellets in Healthy Chinese Volunteers by Liquid Chromatography-electrospray Ionization-tandem Mass Spectrometry.

Science.gov (United States)

Ma, J-Y; Liu, M; Yang, M; Zhao, H; Tong, Y; Zhang, Y; Deng, M; Liu, H

2016-05-01

The pharmacokinetic study of a diclofenac sodium capsule filled with enteric-coated pellets (abbreviated as CAPSULE) in healthy Chinese subjects was evaluated using liquid chromatography-electrospray ionization-tandem mass spectrometry with simple sample preparation. In a cross-over study, 12 healthy male volunteers were given 50 mg CAPSULE and diclofenac sodium enteric-coated tablet (abbreviated as TABLET, used as a control dosage form) at fasting. The Cmax, AUC0-t, and Tmax of CAPSULE were 1.01±0.52 μg/mL, 1.54±0.18 μg·h/mL, and 1.50±1.31 h, respectively. When compared with TABLET, the pharmacokinetic study showed that although this CAPSULE exhibited similar AUC (only 10% lower), it presented lower maximum plasma concentration, faster absorption and shorter time to reach maximum concentration. When compared with the previous study in Germany, obvious variations on Tmax were found in Chinese subjects taking CAPSULE, but not TABLET. The results indicated that individual difference should be paid attention when prescribing CAPSULE to Chinese patients. © Georg Thieme Verlag KG Stuttgart · New York.

Automated pharmaceutical tablet coating layer evaluation of optical coherence tomography images

International Nuclear Information System (INIS)

Markl, Daniel; Sacher, Stephan; Khinast, Johannes G; Hannesschläger, Günther; Leitner, Michael; Buchsbaum, Andreas

2015-01-01

Film coating of pharmaceutical tablets is often applied to influence the drug release behaviour. The coating characteristics such as thickness and uniformity are critical quality parameters, which need to be precisely controlled. Optical coherence tomography (OCT) shows not only high potential for off-line quality control of film-coated tablets but also for in-line monitoring of coating processes. However, an in-line quality control tool must be able to determine coating thickness measurements automatically and in real-time. This study proposes an automatic thickness evaluation algorithm for bi-convex tables, which provides about 1000 thickness measurements within 1 s. Beside the segmentation of the coating layer, optical distortions due to refraction of the beam by the air/coating interface are corrected. Moreover, during in-line monitoring the tablets might be in oblique orientation, which needs to be considered in the algorithm design. Experiments were conducted where the tablet was rotated to specified angles. Manual and automatic thickness measurements were compared for varying coating thicknesses, angles of rotations, and beam displacements (i.e. lateral displacement between successive depth scans). The automatic thickness determination algorithm provides highly accurate results up to an angle of rotation of 30°. The computation time was reduced to 0.53 s for 700 thickness measurements by introducing feasibility constraints in the algorithm. (paper)

Accelerating the dissolution of enteric coatings in the upper small intestine: evolution of a novel pH 5.6 bicarbonate buffer system to assess drug release.

Science.gov (United States)

Varum, Felipe J O; Merchant, Hamid A; Goyanes, Alvaro; Assi, Pardis; Zboranová, Veronika; Basit, Abdul W

2014-07-01

Despite rapid dissolution in compendial phosphate buffers, gastro resistant (enteric coated) products can take up to 2 h to disintegrate in the human small intestine, which clearly highlights the inadequacy of the in vitro test method to predict in vivo behaviour of these formulations. The aim of this study was to establish the utility of a novel pH 5.6 bicarbonate buffer, stabilized by an Auto pH™ System, as a better surrogate of the conditions of the proximal small intestine to investigate the dissolution behaviour of standard and accelerated release enteric double coating formulations. Prednisolone tablets were coated with 3 or 5 mg/cm(2) of partially neutralized EUDRAGIT(®) L 30 D-55, HP-55 or HPMC adjusted to pH 6 or 8. An outer layer of EUDRAGIT(®) L 30 D-55 was applied at 5mg/cm(2). For comparison purposes, a standard single layer of EUDRAGIT(®) L 30 D-55 was applied to the tablets. Dissolution was carried out using USP II apparatus in 0.1 M HCl for 2 h, followed by pH 5.6 bicarbonate buffer. EUDRAGIT(®) L 30 D-55 single-coated tablets showed a slow drug release with a lag time of 75 min in buffer, whereas release from the EUDRAGIT(®) L 30 D-55 double-coated tablets was accelerated. These in vitro lag times closely match the in vivo disintegration times for these coated tablets reported previously. Drug release was further accelerated from modified double coatings, particularly in the case of coatings with a thinner inner layer of HP-55 or HPMC (pH 8 and KH2PO4). This study confirms that the pH 5.6 bicarbonate buffer system offers significant advantages during the development of dosage forms designed to release the drug in the upper small intestine. Copyright © 2014. Published by Elsevier B.V.

Colon Targeted Guar Gum Compression Coated Tablets of Flurbiprofen: Formulation, Development, and Pharmacokinetics

Directory of Open Access Journals (Sweden)

Sateesh Kumar Vemula

2013-01-01

Full Text Available The rationale of the present study is to formulate flurbiprofen colon targeted compression coated tablets using guar gum to improve the therapeutic efficacy by increasing drug levels in colon, and also to reduce the side effects in upper gastrointestinal tract. Direct compression method was used to prepare flurbiprofen core tablets, and they were compression coated with guar gum. Then the tablets were optimized with the support of in vitro dissolution studies, and further it was proved by pharmacokinetic studies. The optimized formulation (F4 showed almost complete drug release in the colon (99.86% within 24 h without drug loss in the initial lag period of 5 h (only 6.84% drug release was observed during this period. The pharmacokinetic estimations proved the capability of guar gum compression coated tablets to achieve colon targeting. The Cmax of colon targeted tablets was 11956.15 ng/mL at Tmax of 10 h whereas it was 15677.52 ng/mL at 3 h in case of immediate release tablets. The area under the curve for the immediate release and compression coated tablets was 40385.78 and 78214.50 ng-h/mL and the mean resident time was 3.49 and 10.78 h, respectively. In conclusion, formulation of guar gum compression coated tablets was appropriate for colon targeting of flurbiprofen.

A New Application of Lipid Nanoemulsions as Coating Agent, Providing Zero-Order Hydrophilic Drug Release from Tablets

Directory of Open Access Journals (Sweden)

Nicolas Anton

2012-01-01

Full Text Available The objective of the present investigation was to evaluate potential of nanoemulsions as a coating material for the tablets. The nanoemulsion of size less than 100 nm was prepared using a simple and low-energy spontaneous emulsification method. Conventional tablets containing theophylline as a model hydrophilic drug were prepared. The theophylline tablets were coated with the nanoemulsion using a fluid bed coater. The effect of different levels of the nanoemulsion coating on the theophylline release was evaluated. The theophylline tablets containing different levels of the nanoemulsion coating could be successfully prepared. Interestingly, the coating of tablet with the nanoemulsion resulted in zero-order release of theophylline from the tablets. The noncoated theophylline tablets release the entire drug in less than 2 minutes, whereas nanoemulsion coating delayed the release of theophylline from tablets. This investigation establishes the proof of concept for the potential of nanoemulsions as a coating material for tablets.

Repackaged sodium valproate tablets--Meeting quality and adherence to ensure seizure control.

Science.gov (United States)

Redmayne, Nichola; Robertson, Sherryl; Kockler, Jutta; Llewelyn, Victoria; Haywood, Alison; Glass, Beverley

2015-09-01

Sodium valproate, which is commonly repacked to assist with adherence to ensure seizure control, is hygroscopic and therefore sensitive to moisture. The aim of this study was thus to determine the stability implications of removing the enteric coated tablets from their original packaging and repackaging into a Dose Administration Aid (DAA) with storage under various environmental conditions. Physicochemical stability of enteric coated sodium valproate tablets repackaged into a DAA and stored at controlled room temperature, accelerated and refrigerated conditions was evaluated for 28 days. A validated high performance liquid chromatography method was used for the quantitation of the drug content. Although the chemical stability (sodium valproate between 95 and 105% of labelled content) was maintained for 28 days for all storage conditions, for those tablets stored under accelerated conditions the integrity of the enteric coat was compromised after only 8 days. Repackaging of enteric coated sodium valproate should be undertaken with caution and be informed by storage climate. This is particularly relevant for those patients living in hot, humid environments where they should be advised to store their DAA in a refrigerator. Copyright © 2015 British Epilepsy Association. Published by Elsevier Ltd. All rights reserved.

Angular circulation speed of tablets in a vibratory tablet coating pan.

Science.gov (United States)

Kumar, Rahul; Wassgren, Carl

2013-03-01

In this work, a single tablet model and a discrete element method (DEM) computer simulation are developed to obtain the angular circulation speed of tablets in a vibratory tablet coating pan for range of vibration frequencies and amplitudes. The models identify three important dimensionless parameters that influence the speed of the tablets: the dimensionless amplitude ratio (a/R), the Froude number (aω2/g), and the tablet-wall friction coefficient, where a is the peak vibration amplitude at the drum center, ω is the vibration angular frequency, R is the drum radius, and g is the acceleration due to gravity. The models predict that the angular circulation speed of tablets increases with an increase in each of these parameters. The rate of increase in the angular circulation speed is observed to decrease for larger values of a/R. The angular circulation speed reaches an asymptote beyond a tablet-wall friction coefficient value of about 0.4. Furthermore, it is found that the Froude number should be greater than one for the tablets to start circulating. The angular circulation speed increases as Froude number increases but then does not change significantly at larger values of the Froude number. Period doubling, where the motion of the bed is repeated every two cycles, occurs at a Froude number larger than five. The single tablet model, although much simpler than the DEM model, is able to predict the maximum circulation speed (the limiting case for a large value of tablet-wall friction coefficient) as well as the transition to period doubling.

Studies on Novel Pantoprazole and Cefuroxime Axetil Tablets for Site Specific Delivery.

OpenAIRE

Putta Rajesh Kumar

2012-01-01

In this study core in coat tablets containing enteric coated Pantaprazole (PP) core and Cefuroxime axetil (CA) floating type coat formulation as single unit prepared by compression coating method. The tablets were evaluated for their various pre-compression, compression characteristics, in vitro drug release kinetics and stability studies. The analytical estimation of drugs was found to be accurate and precise. The results of rheological characteristics indicated that, the powder beds of both...

Colon Targeted Guar Gum Compression Coated Tablets of Flurbiprofen: Formulation, Development, and Pharmacokinetics

Science.gov (United States)

Bontha, Vijaya Kumar

2013-01-01

The rationale of the present study is to formulate flurbiprofen colon targeted compression coated tablets using guar gum to improve the therapeutic efficacy by increasing drug levels in colon, and also to reduce the side effects in upper gastrointestinal tract. Direct compression method was used to prepare flurbiprofen core tablets, and they were compression coated with guar gum. Then the tablets were optimized with the support of in vitro dissolution studies, and further it was proved by pharmacokinetic studies. The optimized formulation (F4) showed almost complete drug release in the colon (99.86%) within 24 h without drug loss in the initial lag period of 5 h (only 6.84% drug release was observed during this period). The pharmacokinetic estimations proved the capability of guar gum compression coated tablets to achieve colon targeting. The C max of colon targeted tablets was 11956.15 ng/mL at T max of 10 h whereas it was 15677.52 ng/mL at 3 h in case of immediate release tablets. The area under the curve for the immediate release and compression coated tablets was 40385.78 and 78214.50 ng-h/mL and the mean resident time was 3.49 and 10.78 h, respectively. In conclusion, formulation of guar gum compression coated tablets was appropriate for colon targeting of flurbiprofen. PMID:24260738

Preparation of Porous Hydroxyapatite Tablets and Porous Hydroxyapatite Coatings for Orthopaedic Use

International Nuclear Information System (INIS)

Mendez-Gonzalez, M.

2004-01-01

Porous hydroxyapatite tablets and coatings on metal substrates were obtained by the addition of polymeric additives and liofilization. Both tablets and coatings were characterized by scanning electron microscopy and x-ray diffraction. Coatings obtained by plasma spraying also exhibited interconnected porous of 100 μm while coatings obtained by laser ablation did not show any porosity. The diffraction patterns of the deposited HA were similar to that of the powder obtained by the precipitation method suggesting that no significant changes occurred during the coating procedure

Development of fi lm forming formulation and technology of polymeric fi lm coating on Indotril tablets

Directory of Open Access Journals (Sweden)

L. I. Kucherenko

2013-09-01

Full Text Available Introduction. In previous researches we grounded expedience of «Indotril» tablets development; formulation and technology of "Indotril" tablet cores were developed. Received tablet cores should be covered by protective polymeric film with the purpose of unpleasant taste elimination, increase of tablets expiration date. Objective. The aim of our investigation was to develop the film forming composition and technology of polymeric film coating on «Indotril» tablets in pseudo-fluidized layer. Materials and Methods. As “Indotril” tablets cores should be covered by protective polymeric film we performed research designed to select efficient film forming solution. Thus modern filming agents were studied, besides such factors were investigated: concentration of film forming suspension, increase of tablet coat in mass, air temperature under gas distribution grid. Obtained tablets were checked according to pharmacopeia methods. Results and discussion. First we studied tablet compression force influence on main parameters of «Indotril» cores tablets: on crushing strength, abrasion in pseudo-fluidized layer unit and disintegration. Then for further investigation we chose «Indotril» cores tablets with crushing strength near 70 H, abrasion - up to 0,5% and disintegration time - not more than 10 minutes. We performed research to select film forming solution for covering “Indotril” tablets in pseudo-fluidized layer unit. As filming agents we used different samples of hydroxypropyl methylcellulose (HPMC by Japan company Shin-Etsu Chemical Co and English company Colorcon. Water HPMC solutions were prepared which contained plasticizer (propylene glycol, pigment (titanium IV dioxide and dye (tartrazine. Coating process of “Indotril” tablets was performed in laboratory pseudo-fluidized layer unit with the air temperature 75ºC under gas distribution grid. Variance analysis of experimental data on quality of coat surface showed insignificance as

Structural changes of polymer-coated microgranules and excipients on tableting investigated by microtomography using synchrotron X-ray radiation.

Science.gov (United States)

Kajihara, Ryusuke; Noguchi, Shuji; Iwao, Yasunori; Suzuki, Yoshio; Terada, Yasuko; Uesugi, Kentaro; Itai, Shigeru

2015-03-15

Multiple-unit tablets consisting of polymer-coated microgranules and excipients have a number of advantageous pharmaceutical properties. Polymer-coated microgranules are known to often lose their functionality because of damage to the polymer coating caused by tableting, and the mechanism of polymer coating damage as well as the structural changes of excipients upon tableting had been investigated but without in-situ visualization and quantitative analysis. To elucidate the mechanism of coating damage, the internal structures of multiple-unit tablets were investigated by X-ray computed microtomography using synchrotron X-rays. Cross sectional images of the tablets with sub-micron spatial resolution clearly revealed that void spaces remained around the compressed excipient particles in the tablets containing an excipient composed of cellulose and lactose (Cellactose(®) 80), whereas much smaller void spaces remained in the tablets containing an excipient made of sorbitol (Parteck(®) SI 150). The relationships between the void spaces and the physical properties of the tablets such as hardness and disintegration were investigated. Damage to the polymer coating in tablets was found mainly where polymer-coated microgranules were in direct contact with each other in both types of tablets, which could be attributed to the difference in hardness of excipient particles and the core of the polymer-coated microgranules. Copyright © 2015 Elsevier B.V. All rights reserved.

Optimization of process parameters for a quasi-continuous tablet coating system using design of experiments.

Science.gov (United States)

Cahyadi, Christine; Heng, Paul Wan Sia; Chan, Lai Wah

2011-03-01

The aim of this study was to identify and optimize the critical process parameters of the newly developed Supercell quasi-continuous coater for optimal tablet coat quality. Design of experiments, aided by multivariate analysis techniques, was used to quantify the effects of various coating process conditions and their interactions on the quality of film-coated tablets. The process parameters varied included batch size, inlet temperature, atomizing pressure, plenum pressure, spray rate and coating level. An initial screening stage was carried out using a 2(6-1(IV)) fractional factorial design. Following these preliminary experiments, optimization study was carried out using the Box-Behnken design. Main response variables measured included drug-loading efficiency, coat thickness variation, and the extent of tablet damage. Apparent optimum conditions were determined by using response surface plots. The process parameters exerted various effects on the different response variables. Hence, trade-offs between individual optima were necessary to obtain the best compromised set of conditions. The adequacy of the optimized process conditions in meeting the combined goals for all responses was indicated by the composite desirability value. By using response surface methodology and optimization, coating conditions which produced coated tablets of high drug-loading efficiency, low incidences of tablet damage and low coat thickness variation were defined. Optimal conditions were found to vary over a large spectrum when different responses were considered. Changes in processing parameters across the design space did not result in drastic changes to coat quality, thereby demonstrating robustness in the Supercell coating process. © 2010 American Association of Pharmaceutical Scientists

A novel in-line NIR spectroscopy application for the monitoring of tablet film coating in an industrial scale process.

Science.gov (United States)

Möltgen, C-V; Puchert, T; Menezes, J C; Lochmann, D; Reich, G

2012-04-15

Film coating of tablets is a multivariate pharmaceutical unit operation. In this study an innovative in-line Fourier-Transform Near-Infrared Spectroscopy (FT-NIRS) application is described which enables real-time monitoring of a full industrial scale pan coating process of heart-shaped tablets. The tablets were coated with a thin hydroxypropyl methylcellulose (HPMC) film of up to approx. 28 μm on the tablet face as determined by SEM, corresponding to a weight gain of 2.26%. For a better understanding of the aqueous coating process the NIR probe was positioned inside the rotating tablet bed. Five full scale experimental runs have been performed to evaluate the impact of process variables such as pan rotation, exhaust air temperature, spray rate and pan load and elaborate robust and selective quantitative calibration models for the real-time determination of both coating growth and tablet moisture content. Principal Component (PC) score plots allowed each coating step, namely preheating, spraying and drying to be distinguished and the dominating factors and their spectral effects to be identified (e.g. temperature, moisture, coating growth, change of tablet bed density, and core/coat interactions). The distinct separation of HPMC coating growth and tablet moisture in different PCs enabled a real-time in-line monitoring of both attributes. A PLS calibration model based on Karl Fischer reference values allowed the tablet moisture trajectory to be determined throughout the entire coating process. A 1-latent variable iPLS weight gain calibration model with calibration samples from process stages dominated by the coating growth (i.e. ≥ 30% of the theoretically applied amount of coating) was sufficiently selective and accurate to predict the progress of the thin HPMC coating layer. At-line NIR Chemical Imaging (NIR-CI) in combination with PLS Discriminant Analysis (PLSDA) verified the HPMC coating growth and physical changes at the core/coat interface during the initial

A new formulation for orally disintegrating tablets using a suspension spray-coating method.

Science.gov (United States)

Okuda, Y; Irisawa, Y; Okimoto, K; Osawa, T; Yamashita, S

2009-12-01

The aim of this study was to design a new orally disintegrating tablet (ODT) that has high tablet hardness and a fast oral disintegration rate using a new preparation method. To obtain rapid disintegration granules (RDGs), a saccharide, such as trehalose, mannitol, or lactose, was spray-coated with a suspension of corn starch using a fluidized-bed granulator (suspension method). As an additional disintegrant, crospovidone, light anhydrous silicic acid, or hydroxypropyl starch was also included in the suspension. The RDGs obtained possessed extremely large surface areas, narrow particle size distribution, and numerous micro-pores. When tabletting these RDGs, it was found that the RDGs increased tablet hardness by decreasing plastic deformation and increasing the contact frequency between granules. In all tablets, a linear relationship was observed between tablet hardness and oral disintegration time. From each linear correlation line, a slope (D/H value) and an intercept (D/H(0) value) were calculated. Tablets with small D/H and D/H(0) values could disintegrate immediately in the oral cavity regardless of the tablet hardness and were considered to be appropriate for ODTs. Therefore, these values were used as key parameters to select better ODTs. Of all the RDGs prepared in this study, mannitol spray-coated with a suspension of corn starch and crospovidone (2.5:1 w/w ratio) showed most appropriate properties for ODTs; fast in vivo oral disintegration time, and high tablet hardness. In conclusion, this simple method to prepare superior formulations for new ODTs was established by spray-coating mannitol with a suspension of appropriate disintegrants.

Assessment of the pharmaceutical quality of marketed enteric coated pantoprazole sodium sesquihydrate products.

Science.gov (United States)

Mostafa, Haitham F; Ibrahim, Mohamed A; Mahrous, Gamal M; Sakr, Adel

2011-04-01

Pantoprazole sodium sesquihydrate (PSS) is a proton pump inhibitor, used in acid-related disorders, like peptic ulcer and gastroesophageal reflux. Increasing the number of pantoprazole containing products in the market, raises questions of its efficacy and generic substitution. The pharmaceutical quality of 6 generic PSS enteric coated tablets in 2 local markets was assessed relative to the innovator product (pantozol®). Uniformity of dosage unit, disintegration and in vitro drug release were determined using United States pharmacopeia for delayed release tablets. The similarity factor (f2) was assessed using the FDA recommended approach (f2 similarity factor). The content uniformity of the innovator product was 98.39% of the labeled claim with RSD value of 1.08%, while the content of generic products ranged from 96.98% to 98.80% with RSD values of 1.24-2.19%. All the products showed no disintegration, cracks or swelling in 0.1 N HCl, except product 1, which showed complete disintegration after 20 min. However, the disintegration of all the products in phosphate buffer met USP requirements. Dissolution of tablets in 0.1 N HCl showed no drug release after 2 h except product 1 in which one tablet showed a drug release more than 10% at acid stage level A1. In addition, three tablets of this product showed dissolution of 45%, 48% and 69% at acid stage level A2. The similarity factor f2 of the products was between 71 and 74 indicating the similarity in dissolution profiles of all the products in accordance to FDA requirements, except product 1 in which f2 value was 18.67.

Effect of the External Lubrication Method for a Rotary Tablet Press on the Adhesion of the Film Coating Layer.

Science.gov (United States)

Kondo, Hisami; Toyota, Hiroyasu; Kamiya, Takayuki; Yamashita, Kazunari; Hakomori, Tadashi; Imoto, Junko; Kimura, Shin-Ichiro; Iwao, Yasunori; Itai, Shigeru

2017-01-01

External lubrication is a useful method which reduces the adhesion of powder to punches and dies by spraying lubricants during the tableting process. However, no information is available on whether the tablets prepared using an external lubrication system can be applicable for a film coating process. In this study, we evaluated the adhesion force of the film coating layer to the surface of tablets prepared using an external lubrication method, compared with those prepared using internal lubrication method. We also evaluated wettability, roughness and lubricant distribution state on the tablet surface before film coating, and investigated the relationship between peeling of the film coating layer and these tablet surface properties. Increasing lubrication through the external lubrication method decreased wettability of the tablet surface. However, no change was observed in the adhesion force of the film coating layer. On the other hand, increasing lubrication through the internal lubrication method, decreased both wettability of the tablet surface and the adhesion force of the film coating layer. The magnesium stearate distribution state on the tablet surface was assessed using an X-ray fluorescent analyzer and lubricant agglomerates were observed in the case of the internal lubrication method. However, the lubricant was uniformly dispersed in the external lubrication samples. These results indicate that the distribution state of the lubricant affects the adhesion force of the film coating layer, and external lubrication maintained sufficient lubricity and adhesion force of the film coating layer with a small amount of lubricant.

Bilayer tablets of Paliperidone for Extended release osmotic drug delivery

Science.gov (United States)

Chowdary, K. Sunil; Napoleon, A. A.

2017-11-01

The purpose of this study is to develop and optimize the formulation of paliperidone bilayer tablet core and coating which should meet in vitro performance of trilayered Innovator sample Invega. Optimization of core formulations prepared by different ratio of polyox grades and optimization of coating of (i) sub-coating build-up with hydroxy ethyl cellulose (HEC) and (ii).enteric coating build-up with cellulose acetate (CA). Some important influence factors such as different core tablet compositions and different coating solution ingredients involved in the formulation procedure were investigated. The optimization of formulation and process was conducted by comparing different in vitro release behaviours of Paliperidone. In vitro dissolution studies of Innovator sample (Invega) with formulations of different release rate which ever close release pattern during the whole 24 h test is finalized.

Formulation and optimization of chronomodulated press-coated tablet of carvedilol by Box–Behnken statistical design

Directory of Open Access Journals (Sweden)

Satwara RS

2012-08-01

Full Text Available Rohan S Satwara, Parul K PatelDepartment of Pharmaceutics, Babaria Institute of Pharmacy, Vadodara, Gujarat, IndiaObjective: The primary objective of the present investigation was to formulate and optimize chronomodulated press-coated tablets to deliver the antihypertensive carvedilol at an effective quantity predawn, when a blood pressure spike is typically observed in most hypertensive patients.Experimental work: Preformulation studies and drug excipient compatibility studies were carried out for carvedilol and excipients. Core tablets (6 mm containing carvedilol and 10-mm press-coated tablets were prepared by direct compression. The Box–Behnken experimental design was applied to these press-coated tablets (F1–F15 formula with differing concentrations of rate-controlling polymers. Hydroxypropyl methyl cellulose K4M, ethyl cellulose, and K-carrageenan were used as rate-controlling polymers in the outer layer. These tablets were subjected to various precompression and postcompression tests. The optimized batch was derived both by statistically (using desirability function and graphically (using Design Expert® 8; Stat-Ease Inc. Tablets formulated using the optimized formulas were then evaluated for lag time and in vitro dissolution.Results and discussion: Results of preformulation studies were satisfactory. No interaction was observed between carvedilol and excipients by ultraviolet, Fourier transform infrared spectroscopy, and dynamic light scattering analysis. The results of precompression studies and postcompression studies were within limits. The varying lag time and percent cumulative carvedilol release after 8 h was optimized to obtain a formulation that offered a release profile with 6 h lag time, followed by complete carvedilol release after 8 h. The results showed no significant bias between predicted response and actual response for the optimized formula.Conclusion: Bedtime dosing of chronomodulated press-coated tablets may offer a

Determination of drug, excipients and coating distribution in pharmaceutical tablets using NIR-CI

Directory of Open Access Journals (Sweden)

Anna Palou

2012-04-01

Full Text Available The growing interest of the pharmaceutical industry in Near Infrared-Chemical Imaging (NIR-CI is a result of its high usefulness for quality control analyses of drugs throughout their production process (particularly of its non-destructive nature and expeditious data acquisition. In this work, the concentration and distribution of the major and minor components of pharmaceutical tablets are determined and the spatial distribution from the internal and external sides has been obtained. In addition, the same NIR-CI allowed the coating thickness and its surface distribution to be quantified. Images were processed to extract the target data and calibration models constructed using the Partial Least Squares (PLS algorithms. The concentrations of Active Pharmaceutical Ingredient (API and excipients obtained for uncoated cores were essentially identical to the nominal values of the pharmaceutical formulation. But the predictive ability of the calibration models applied to the coated tablets decreased as the coating thickness increased. Keywords: Near infrared Chemical Imaging (NIR-CI, Hyperspectral imaging, Component distribution, Tablet coating distribution, Partial Least Squares (PLS regression

Dry coating of micronized API powders for improved dissolution of directly compacted tablets with high drug loading.

Science.gov (United States)

Han, Xi; Ghoroi, Chinmay; Davé, Rajesh

2013-02-14

Motivated by our recent study showing improved flow and dissolution rate of the active pharmaceutical ingredient (API) powders (20 μm) produced via simultaneous micronization and surface modification through continuous fluid energy milling (FEM) process, the performance of blends and direct compacted tablets with high drug loading is examined. Performance of 50 μm API powders dry coated without micronization is also considered for comparison. Blends of micronized, non-micronized, dry coated or uncoated API powders at 30, 60 and 70% drug loading, are examined. The results show that the blends containing dry coated API powders, even micronized ones, have excellent flowability and high bulk density compared to the blends containing uncoated API, which are required for direct compaction. As the drug loading increases, the difference between dry coated and uncoated blends is more pronounced, as seen in the proposed bulk density-FFC phase map. Dry coating led to improved tablet compactibility profiles, corresponding with the improvements in blend compressibility. The most significant advantage is in tablet dissolution where for all drug loadings, the t(80) for the tablets with dry coated APIs was well under 5 min, indicating that this approach can produce nearly instant release direct compacted tablets at high drug loadings. Copyright © 2012 Elsevier B.V. All rights reserved.

Implementation of quality by design approach in manufacturing process optimization of dry granulated, immediate release, coated tablets - a case study.

Science.gov (United States)

Teżyk, Michał; Jakubowska, Emilia; Milanowski, Bartłomiej; Lulek, Janina

2017-10-01

The aim of this study was to optimize the process of tablets compression and identification of film-coating critical process parameters (CPPs) affecting critical quality attributes (CQAs) using quality by design (QbD) approach. Design of experiment (DOE) and regression methods were employed to investigate hardness, disintegration time, and thickness of uncoated tablets depending on slugging and tableting compression force (CPPs). Plackett-Burman experimental design was applied to identify critical coating process parameters among selected ones that is: drying and preheating time, atomization air pressure, spray rate, air volume, inlet air temperature, and drum pressure that may influence the hardness and disintegration time of coated tablets. As a result of the research, design space was established to facilitate an in-depth understanding of existing relationship between CPPs and CQAs of intermediate product (uncoated tablets). Screening revealed that spray rate and inlet air temperature are two most important factors that affect the hardness of coated tablets. Simultaneously, none of the tested coating factors have influence on disintegration time. The observation was confirmed by conducting film coating of pilot size batches.

Evaluating the effect of coating equipment on tablet film quality using terahertz pulsed imaging

DEFF Research Database (Denmark)

Haaser, Miriam; Naelapaa, Kaisa; Gordon, Keith C

2013-01-01

In this study, terahertz pulsed imaging (TPI) was employed to investigate the effect of the coating equipment (fluid bed and drum coater) on the structure of the applied film coating and subsequent dissolution behaviour. Six tablets from every batch coated with the same delayed release coating fo...

Development and Efficacy Assessment of an Enteric Coated Porous Tablet Loaded With F4 Fimbriae for Oral Vaccination of Piglets against F4+ Escherichia coli Infections.

Science.gov (United States)

Srivastava, Atul; Gowda, D V; Madhunapantula, SubbaRao V; Siddaramaiah

2016-01-01

Enterotoxigenic Escherichia coli (ETEC) infection is one of the major causes contributing to the development of diarrhoea and mortality in new born, suckling and newly weaned piglets. To date, no preventive/treatment strategy showed promising results, which could be due to the lack of potent vaccines, and/or due to the development of resistance of ETEC to antibiotics. Therefore, in the present investigation, a novel porous sodium alginate (SA) tablet formulation loaded with F4 fimbriae antigen was developed and tested for efficacy against ETEC infections in piglet models. Precompression parameters of the powder mixes and post compression parameters of tablets have been evaluated and results were found to be satisfactory. Loading of F4 fimbrial antigens into the tablets was achieved by inducing pores in the tablets via the sublimation of camphor followed by incubation with purified F4 fimbriae. The loaded tablets have been coated with Eudragit L100 to protect the F4 fimbriae from (a) highly acidic gastric environment; (b) proteolytic cleavage by pepsin; and (c) to promote subsequent release in the intestine. Evaluation of developed F4 fimbrial tablets in a Pig model demonstrated induction of mucosal immunity, and a significant reduction of F4+ E. coli in faeces. Therefore, F4 fimbriae loaded porous tablets could be a novel oral vaccination candidate to induce mucosal and systemic immunity against ETEC infections.

A Novel Approach to Flurbiprofen Pulsatile Colonic Release: Formulation and Pharmacokinetics of Double-Compression-Coated Mini-Tablets.

Science.gov (United States)

Vemula, Sateesh Kumar

2015-12-01

A significant plan is executed in the present study to study the effect of double-compression coating on flurbiprofen core mini-tablets to achieve the pulsatile colonic delivery to deliver the drug at a specific time as per the patho-physiological need of the disease that results in improved therapeutic efficacy. In this study, pulsatile double-compression-coated tablets were prepared based on time-controlled hydroxypropyl methylcellulose K100M inner compression coat and pH-sensitive Eudragit S100 outer compression coat. Then, the tablets were evaluated for both physical evaluation and drug-release studies, and to prove these results, in vivo pharmacokinetic studies in human volunteers were conducted. From the in vitro drug-release studies, F6 tablets were considered as the best formulation, which retarded the drug release in the stomach and small intestine (3.42 ± 0.12% in 5 h) and progressively released to the colon (99.78 ± 0.74% in 24 h). The release process followed zero-order release kinetics, and from the stability studies, similarity factor between dissolution data before and after storage was found to be 88.86. From the pharmacokinetic evaluation, core mini-tablets producing peak plasma concentration (C max) was 14,677.51 ± 12.16 ng/ml at 3 h T max and pulsatile colonic tablets showed C max = 12,374.67 ± 16.72 ng/ml at 12 h T max. The area under the curve for the mini and pulsatile tablets was 41,238.52 and 72,369.24 ng-h/ml, and the mean resident time was 3.43 and 10.61 h, respectively. In conclusion, development of double-compression-coated tablets is a promising way to achieve the pulsatile colonic release of flurbiprofen.

Pharmacokinetics of hydrocodone extended-release tablets formulated with different levels of coating to achieve abuse deterrence compared with a hydrocodone immediate-release/acetaminophen tablet in healthy subjects.

Science.gov (United States)

Darwish, Mona; Bond, Mary; Tracewell, William; Robertson, Philmore; Yang, Ronghua

2015-01-01

A hydrocodone extended-release (ER) formulation employing the CIMA(®) Abuse-Deterrence Technology platform was developed to provide resistance against rapid release of hydrocodone when tablets are comminuted or taken with alcohol. This study evaluated the pharmacokinetics of three hydrocodone ER tablet prototypes with varying levels of polymer coating to identify the prototype expected to have the greatest abuse deterrence potential based on pharmacokinetic characteristics that maintain systemic exposure to hydrocodone comparable to that of a commercially available hydrocodone immediate-release (IR) product. In this four-period crossover study, healthy subjects aged 18-45 years were randomized to receive a single intact, oral 45-mg tablet of one of three hydrocodone ER prototypes (low-, intermediate-, or high-level coating) or an intact, oral tablet of hydrocodone IR/acetaminophen (APAP) 10/325 mg every 6 h until four tablets were administered, with each of the four treatments administered once over the four study periods. Dosing periods were separated by a minimum 5-day washout. Naltrexone 50 mg was administered to block opioid receptors. Blood samples for pharmacokinetic assessments were collected predose and through 72 h postdose. Parameters assessed included maximum observed plasma hydrocodone concentration (C(max)), time to C(max) (t(max)), and area under the concentration-time curve from time 0 to infinity (AUC(0-∞)). Mean C(max) values were 49.2, 32.6, and 28.4 ng/mL for the low-, intermediate-, and high-level coating hydrocodone ER tablet prototypes, respectively, and 37.3 ng/mL for the hydrocodone IR/APAP tablet; respective median t(max) values were 5.9, 8.0, 8.0, and 1.0 h. Total systemic exposure to hydrocodone (AUC(0-∞)) was comparable between hydrocodone ER tablet prototypes (640, 600, and 578 ng·h/mL, respectively) and hydrocodone IR/APAP (581 ng·h/mL). No serious adverse events or deaths were reported. The most common adverse events included

Guargum and Eudragit ® coated curcumin liquid solid tablets for colon specific drug delivery.

Science.gov (United States)

S Kumar, Vrinda; Rijo, John; M, Sabitha

2018-04-15

Colorectal cancer, also known as bowel cancer, is the uncontrolled cell growth in the colon or rectum (parts of the large intestine), or in the appendix. The colon specific drug delivery would alleviate the systemic side effects and would assure the safe therapy for colonic disorders with minimum dose and duration of therapy. The liquisolid technique refers to solubilisation of drug in a non-volatile solvent combined with inclusion of appropriate carrier and coating agent required for tableting. Colon specific degradation of natural polymer, guar gum and pH dependant degradative (pH-7) property of eudragit L100 restricts the delivery of curcumin in gastric and intestinal pH. Formulated curcumin liquisolid powder was evaluated for the micrometric properties, solubility and by differential thermal analysis, X ray powder diffraction and scanning electron microscopy. Curcumin loaded liquisolid tablet showed more anticancer activity against HCT-15 compared with free curcumin. Bioavailability study of the coated and uncoated liquisolid tablets were performed using Newzealand white rabbits. The present study concludes that liquisolid technique is a promising alternative for improving oral bioavailability and dissolution rate of water insoluble drug and coating liquisolid tablet with colon sensitive polymers showed site specific release of drug in the colon. Copyright © 2018 Elsevier B.V. All rights reserved.

Development and Evaluation of a Novel Pellet-Based Tablet System for Potential Colon Delivery of Budesonide

Directory of Open Access Journals (Sweden)

Jaleh Varshosaz

2012-01-01

Full Text Available Budesonide, a potent glucocorticoid, is used for the treatment of inflammatory bowel diseases. Current available oral formulations of budesonide have low efficacy against ulcerative colitis because of the premature drug release in the upper part of the gastrointestinal tract. In this paper a pH- and time-controlled colon-targeted pellet-based tablet of budesonide was established. Pellet cores were prepared by extrusion-spheronization method and further coated with xanthan gum (barrier layer, Eudragit NE30D and L30D55 combination (inner layer, and Eudragit FS30 (as enteric layer sequentially to achieve the required release profile. The coated pellets then compressed into tablets using inert tabletting granules of Cellactose or Pearlitol. Release studies, performed in simulated gastric, intestinal, and colon pH were used in sequence to mimic the gastrointestinal transit. The influence of formulation variables like barrier layer thickness, inner layer composition, and enteric coat thickness on drug release were investigated and the coated pellets that contained 12% weight gain in xanthan gum layer, Eudragit L30D55 and Eudragit NE30D with a ratio of 3 : 7 in inner layer with 30% weight gain and 25% weight gain in Eudragit FS layer were found to protect the drug release in stomach and small intestine and 83.35 ± 2.4 of budesonide was released at 24 h. The drug release from the tablets prepared using 40% Cellactose 80 as tableting excipient was found to be closely similar to that of uncompressed pellets.

Formulation and in vitro and in vivo evaluation of film-coated montelukast sodium tablets using Opadry® yellow 20A82938 on an industrial scale

Directory of Open Access Journals (Sweden)

Zaid AN

2013-02-01

Full Text Available Abdel Naser Zaid,1 Salam Natur,2 Aiman Qaddumi,2 Abeer Abu Ghoush11Department of Pharmacy, Faculty of Medicine and Health Sciences, An-Najah National University, Nablus, Palestine; 2Pharmacare PLC, Ramallah, PalestinePurpose: The aim of this study was to formulate stable film-coated montelukast sodium (MS tablets using Opadry® yellow 20A82938 (Montikast® tablets and to evaluate their in vitro and in vivo release profile.Methods: MS core tablets were manufactured using a direct compression method. Opadry yellow 20A82938 aqueous coating dispersion was used as the film-coating material. Dissolution of the film-coated tablets was tested in 900 mL of 0.5% sodium lauryl sulfate solution and the bioequivalence of the tablets was tested by comparing them with a reference formulation – Singulair® tablets. In vitro–in vivo correlation was evaluated. The stability of the obtained film-coated tablets was evaluated according to International Conference on Harmonisation of Technical Requirements for Registration of Pharmaceuticals for Human Use guidelines.Results: The efficiency of the film coating was determined by subjecting the coated tablets to gastric pH and drug release was analyzed using high-performance liquid chromatography. The coated tablets had no obvious defects. MS release met the study criterion of not less than 80% dissolved after 30 minutes in 0.5% sodium lauryl sulfate solution. Statistical comparison of the main pharmacokinetic parameters clearly indicated no significant difference between test and reference in any of the calculated pharmacokinetic parameters. Level A correlation between in vitro drug release and in vivo absorption was found to be satisfactory.Conclusion: These findings suggest that aqueous film coating with Opadry yellow 20A82938 is an easy, reproducible, and economical approach for preparing stable MS film-coated tablets without affecting the drug-release characteristics.Keywords: coating, stability, aqueous

Development and evaluation of microporous osmotic tablets of diltiazem hydrochloride

Directory of Open Access Journals (Sweden)

Afifa Bathool

2012-01-01

Full Text Available Microporous osmotic tablet of diltiazem hydrochloride was developed for colon targeting. These prepared microporous osmotic pump tablet did not require laser drilling to deliver the drug to the specific site of action. The tablets were prepared by wet granulation method. The prepared tablets were coated with microporous semipermeable membrane and enteric polymer using conventional pan coating process. The incorporation of sodium lauryl sulfate (SLS, a leachable pore-forming agent, could form in situ delivery pores while coming in contact with gastrointestinal medium. The effect of formulation variables was studied by changing the amounts of sodium alginate and NaCMC in the tablet core, osmogen, and that of pore-forming agent (SLS used in the semipermeable coating. As the amount of hydrophilic polymers increased, drug release rate prolonged. It was found that drug release was increased as the concentration of osmogen and pore-former was increased. Fourier transform infrared spectroscopy and Differential scanning calorimetry results showed that there was no interaction between drug and polymers. Scanning electron microscopic studies showed the formation of pores after predetermined time of coming in contact with dissolution medium. The formation of pores was dependent on the amount of pore former used in the semipermeable membrane. in vitro results showed acid-resistant, timed release at an almost zero order up to 24 hours. The developed osmotic tablets could be effectively used for prolonged delivery of Diltiazem HCl.

Development and evaluation of a hot-melt coating technique for enteric coating

Directory of Open Access Journals (Sweden)

Arun Trambak Patil

2012-03-01

Full Text Available Conventional enteric coating requires the use of organic based polymers which are equally hazardous to the environment and operating personnel. Hot-melt coating avoids the use of solvents and is a safer and time-saving process. The present study was designed to assess the efficacy of hot-melt coating (HMC as an enteric coating technique. Pellets prepared by extrusion spheronization were selected as the core formulation for a model of the gastric irritant drug diclofenac sodium (DFS because of their innate advantages over single-unit formulations. Stearic acid (SA and palmitic acid (PA were evaluated as enteric hot-melt coating materials. HMC was carried out in a specially modified coating pan by applying SA and PA in molten state onto preheated pellets to achieve a coating level of 5-15 %w/w. Hot-melt coated pellets were evaluated for disintegration pH and in vitro dissolution in the pH range 1.2 to 6.8, along with basic micromeritics. SEM of coated pellets showed a uniform and smooth coating. These results indicated that HMC of both SA and PA exhibited very good enteric coating ability. The coated pellets showed negligible drug release in acidic pH. As the pellets were subsequently transferred to a higher pH level, a gradual increase in release of the drug from the pellets was observed with increasing pH of the dissolution media. The release was dependent upon coating extent, providing sustained enteric release as opposed to abrupt release with mixed release kinetics.O revestimento entérico convencional requer o uso de polímeros orgânicos os quais são igualmente danosos ao meio ambiente e ao pessoal que o executa. O revestimento por fusão a quente evita o uso de solventes e é processo mais seguro e que consome menos tempo. O presente estudo foi planejado para avaliar a eficácia do revestimento por fusão a quente (RFQ como técnica de revestimento entérico. Os péletes preparados por esferonização por extrusão foram selecionados como

Enteric coating of granules containing the probiotic Lactobacillus acidophilus

Directory of Open Access Journals (Sweden)

Pyar Hassan

2014-06-01

Full Text Available In the present study, a capsule formulation composed of enteric coated granules of Lactobacillus acidophilus ATCC 4962 was developed using Eudragit L30D-55 as enteric polymer. Optimization of the capsule formulation was achieved with a maximum viable cell count after 2 h of incubation in acid medium and disintegration time of 1 h in buffer pH 6.8. The amount of Eudragit L30D-55 in the capsules correlated with gastric juice resistance. The best protective qualities against artificial gastric juice were observed when capsules were prepared from granules composed of L. acidophilus, corn starch, lactose monohydrate, polyvinylpyrrolidone and coated with 12.5 % (m/V of Eudragit L30D-55. Capsule formulation of L. acidophilus in edible broth medium suspension serves as a cheap alternative to the expensive freeze-drying procedure for preparing L. acidophilus. In addition, the enteric coating using Eudragit L30D-55 could protect probiotics from the acidic gastric environment and enhance the bioactivity of probiotics along with replacement of pathogenic microbes in human intestine

How do tablet properties influence swallowing behaviours?

Science.gov (United States)

Yamamoto, Shinya; Taniguchi, Hiroshige; Hayashi, Hirokazu; Hori, Kazuhiro; Tsujimura, Takanori; Nakamura, Yuki; Sato, Hideaki; Inoue, Makoto

2014-01-01

Behavioural performance of tablet swallowing was evaluated with different tablet conditions in terms of size, number and surface coating. Four different types of tablets were prepared: small or large, and with or without a surface coating. Fourteen normal male adults were instructed to swallow the prepared tablets with 15 ml of water. The number of tablets in one trial was changed from one to three. To evaluate swallowing and tablet transport, electromyographic activity was recorded in the left suprahyoid muscles, and videofluorographic images were examined. All tablet conditions (size, number and surface coating) affected the swallowing performance in terms of total number of swallows, electromyographic burst patterns and location of remaining tablets. Increases in the size and number of tablets increased the number of swallows and electromyographic burst area and duration. In addition, all of these parameters increased while swallowing tablets without a coating compared with tablets with a coating. Location of the remaining tablets was mainly within the mouth. This study only clarified the normal pattern of tablet swallowing under several conditions in healthy subjects, but the results may facilitate comprehensive evaluation and treatment planning in terms of administering medication to dysphagic patients. © 2013 Royal Pharmaceutical Society.

Eudragit L/HPMCAS blend enteric-coated lansoprazole pellets: enhanced drug stability and oral bioavailability.

Science.gov (United States)

Fang, Yu; Wang, Guozheng; Zhang, Rong; Liu, Zhihua; Liu, Zhenghua; Wu, Xiaohui; Cao, Deying

2014-06-01

The objectives of the present work were to use blends of Eudragit L and hydroxypropyl methylcellulose acetate succinate (HPMCAS) as enteric film coatings for lansoprazole (LSP) pellets. The enteric-coated pellets were prepared with a fluid-bed coater. The influence of the blend ratio, type of plasticizer, plasticizer level, coating level, and curing conditions on gastric stability in vitro drug release and drug stability was evaluated. Furthermore, the bioavailability of the blend-coated pellets in beagle dogs was also performed. The blend-coated pellets exhibited significant improvement of gastric stability and drug stability compared to the pure polymer-coated pellets. Moreover, the AUC values of blend-coated pellets were greater than that of the pure polymer-coated pellets. It was concluded that the using blends of Eudragit L and HPMCAS as enteric film coatings for LSP pellets improved the drug stability and oral bioavailability.

In-vitro studies of enteric coated diclofenac sodium-carboxymethylcellulose microspheres.

Science.gov (United States)

Arica, B; Arica, M Y; Kaş, H S; Hincal, A A; Hasirci, V

1996-01-01

MIcrospheres containing diclofenac sodium (DS) were prepared using carboxymethylcellulose (CMC) as the main support material (1.0, 2.0, 3.0% (w/v)) and aluminum chloride as the crosslinker. Drug to polymer ratios of 1:1, 1:2 and 1:4 were used to obtain a range of microspheres. The microspheres were then coated with an enteric coating material, Eudragit S-100, efficiency, % yield value, particle sizes an in-vitro dissolution behaviour were investigated. The surface of the enteric coated microspheres seemed to be all covered with Eudragit S-100 from scanning electron microscopy observation. It was also observed that increasing the CMC concentration led to an increase in the encapsulation efficiency, % yield value and particle size and decreased the release rate. Eudragit S-100 coating did not significantly alter the size but the release rate was significantly lower even when the lower concentration solution was used.

Tablet potency of Tianeptine in coated tablets by near infrared spectroscopy: model optimisation, calibration transfer and confidence intervals.

Science.gov (United States)

Boiret, Mathieu; Meunier, Loïc; Ginot, Yves-Michel

2011-02-20

A near infrared (NIR) method was developed for determination of tablet potency of active pharmaceutical ingredient (API) in a complex coated tablet matrix. The calibration set contained samples from laboratory and production scale batches. The reference values were obtained by high performance liquid chromatography (HPLC) and partial least squares (PLS) regression was used to establish a model. The model was challenged by calculating tablet potency of two external test sets. Root mean square errors of prediction were respectively equal to 2.0% and 2.7%. To use this model with a second spectrometer from the production field, a calibration transfer method called piecewise direct standardisation (PDS) was used. After the transfer, the root mean square error of prediction of the first test set was 2.4% compared to 4.0% without transferring the spectra. A statistical technique using bootstrap of PLS residuals was used to estimate confidence intervals of tablet potency calculations. This method requires an optimised PLS model, selection of the bootstrap number and determination of the risk. In the case of a chemical analysis, the tablet potency value will be included within the confidence interval calculated by the bootstrap method. An easy to use graphical interface was developed to easily determine if the predictions, surrounded by minimum and maximum values, are within the specifications defined by the regulatory organisation. Copyright © 2010 Elsevier B.V. All rights reserved.

Stabilization Mechanism of Roxithromycin Tablets under Gastric pH Conditions.

Science.gov (United States)

Inukai, Koki; Noguchi, Shuji; Kimura, Shin-Ichiro; Itai, Shigeru; Iwao, Yasunori

2018-05-31

Macrolide antibiotics are widely used at clinical sites. Clarithromycin (CAM), a 14-membered macrolide antibiotic, was reported to gelate under acidic conditions. Gelation allows oral administration of acid-sensitive CAM without enteric coating by hindering the penetration of gastric fluid into CAM tablets. However, it is unknown whether this phenomenon occurs in other macrolide antibiotics. In this study, we examined the gelation ability of three widely used macrolide antibiotics, roxithromycin (RXM), erythromycin A (EM), and azithromycin (AZM). The results indicated that not only CAM but also RXM gelated under acidic conditions. EM and AZM did not gelate under the same conditions. Gelation of RXM delayed the disintegration of the tablet and release of RXM from the tablet. Disintegration and release were also delayed in commercial RXM tablets containing disintegrants. This study showed that two of the four macrolides gelated, which affects tablet disintegration and dissolution and suggests that this phenomenon might also occur in other macrolides. Copyright © 2018. Published by Elsevier Inc.

Application of a tablet film coating model to define a process-imposed transition boundary for robust film coating.

Science.gov (United States)

van den Ban, Sander; Pitt, Kendal G; Whiteman, Marshall

2018-02-01

A scientific understanding of interaction of product, film coat, film coating process, and equipment is important to enable design and operation of industrial scale pharmaceutical film coating processes that are robust and provide the level of control required to consistently deliver quality film coated product. Thermodynamic film coating conditions provided in the tablet film coating process impact film coat formation and subsequent product quality. A thermodynamic film coating model was used to evaluate film coating process performance over a wide range of film coating equipment from pilot to industrial scale (2.5-400 kg). An approximate process-imposed transition boundary, from operating in a dry to a wet environment, was derived, for relative humidity and exhaust temperature, and used to understand the impact of the film coating process on product formulation and process control requirements. This approximate transition boundary may aid in an enhanced understanding of risk to product quality, application of modern Quality by Design (QbD) based product development, technology transfer and scale-up, and support the science-based justification of critical process parameters (CPPs).

Application of process analytical technology in tablet process development using NIR spectroscopy : Blend uniformity, content uniformity and coating thickness measurements

NARCIS (Netherlands)

Moes, Johannes J; Ruijken, Marco M; Gout, Erik; Frijlink, Henderik W; Ugwoke, Michael I

2008-01-01

Near-infrared (NIR)spectroscopy was employed as a process analytical technique in three steps of tabletting process: to monitor the blend homogeneity, evaluate the content uniformity of tablets and determine the tablets coating thickness. A diode-array spectrometer mounted on a lab blender (SP15 NIR

Effects of tablet formulation and subsequent film coating on the supersaturated dissolution behavior of amorphous solid dispersions.

Science.gov (United States)

Sakai, Toshiro; Hirai, Daiki; Kimura, Shin-Ichiro; Iwao, Yasunori; Itai, Shigeru

2018-04-05

The effects of tablet preparation and subsequent film coating with amorphous solid dispersion (ASD) particles that were composed of a drug with poor water solubility and hydrophilic polymers were investigated. ASD particles were prepared with a drug and vinylpyrrolidone-vinyl acetate copolymer (PVPVA) or polyvinylpyrrolidone (PVP) at a weight ratio of 1:1 or 1:2 using a melt extrusion technique. Tablets were prepared by conventional direct compression followed by pan coating. A mathematical model based on the Noyes-Whitney equation assuming that stable crystals precipitated at the changeable surface area of the solid-liquid interface used to estimate drug dissolution kinetics in a non-sink dissolution condition. All the ASD particles showed a maximum dissolution concentration approximately ten times higher than that of the crystalline drug. The ASD particles with PVPVA showed higher precipitation rate with lower polymer ratio, while PVP did not precipitate within 960 min regardless of the polymer ratio, suggesting the ASD particles of 1:1 drug:PVPVA (ASD-1) were the most unstable among the ASD particles considered. The dissolution of a core tablet with ASD-1 showed less supersaturation and a much higher precipitation rate than those of ASD-1 particles. However, a film-coated tablet or core tablet with a trace amount of hydroxypropylmethylcellulose (HPMC) showed a similar dissolution profile to that of the ASD-1 particles, indicating HPMC had a remarkable precipitation inhibition effect. Overall, these results suggest that tablet preparation with ASD may adversely affect the maintenance of supersaturation; however, this effect can be mitigated by adding an appropriate precipitation inhibitor to the formulation. Copyright © 2018 Elsevier B.V. All rights reserved.

Film coated tablets (ColoPulse technology) for targeted delivery in the lower intestinal tract : influence of the core composition on release characteristics

NARCIS (Netherlands)

Schellekens, Reinout C. A.; Baltink, Jan H.; Woesthuis, Ellen M.; Stellaard, Frans; Kosterink, Jos G. W.; Woerdenbag, Herman J.; Frijlink, Henderik W.

2010-01-01

The design of a film coating technology which allows a tablet to deliver the drug in the ileocolonic segment would offer new treatment possibilities. The objective is to develop a platform technology that is suitable for a broad range of drug compounds. We developed a coated tablet with a delayed,

Drug Resistance and Pseudoresistance: An Unintended Consequence of Enteric Coating Aspirin

Science.gov (United States)

Grosser, Tilo; Fries, Susanne; Lawson, John A.; Kapoor, Shiv C.; Grant, Gregory R.; FitzGerald, Garret A.

2013-01-01

Background Low dose aspirin reduces the secondary incidence of myocardial infarction and stroke. Drug resistance to aspirin might result in treatment failure. Despite this concern, no clear definition of “aspirin resistance” has emerged and estimates of its incidence have varied remarkably. We aimed to determine the commonality of a mechanistically consistent, stable and specific phenotype of true pharmacological resistance to aspirin – such as might be explained by genetic causes. Methods and Results Healthy volunteers (n=400) were screened for their response to a single oral dose of 325 mg immediate release or enteric coated aspirin. Response parameters reflected the activity of aspirin's molecular target, cyclooxygenase-1. Individuals who appeared “aspirin resistant” on one occasion underwent repeat testing and if still “resistant” were exposed to low dose enteric coated aspirin (81 mg) and clopidogrel (75 mg) for one week each. Variable absorption caused a high frequency of apparent resistance to a single dose of 325 mg enteric coated aspirin (up to 49%) but not to immediate release aspirin (0%). All individuals responded to aspirin upon repeated exposure, extension of the post dosing interval or addition of aspirin to their platelets ex vivo. Conclusions Pharmacological resistance to aspirin is rare; this study failed to identify a single case of true drug resistance. Pseudoresistance, reflecting delayed and reduced drug absorption, complicates enteric coated but not immediate release aspirin administration. Clinical Trial Registration Information clinicaltrials.gov. Identifier: NCT00948987. PMID:23212718

Comparative Evaluation and Optimization of Film Coating ...

African Journals Online (AJOL)

In this study, hydroxypropyl methylcellulose phthalate (HPMCP) and two polymethacrylates, Wangit L30D-55® and Wangit L-100® were investigated for their enteric coating properties using diclofenac sodium tablets as core. Both polymers showed acid protective effect at the weight gain of 6%. Polymethacrylate based ...

Clinical Efficacy and Residue Depletion of 10% Enrofloxacin Enteric-Coated Granules in Pigs.

Science.gov (United States)

Lei, Zhixin; Liu, Qianying; Yang, Bing; Xiong, Jincheng; Li, Kun; Ahmed, Saeed; Hong, Liping; Chen, Pin; He, Qigai; Cao, Jiyue

2017-01-01

A new, more palatable formulation of 10% enrofloxacin enteric-coated granules was investigated to evaluate the pharmacokinetic effect in plasma, the residue elimination in tissues and the clinical efficacy against Actinobacillus pleuropneumonia (APP) and Mycoplasam suis (MS) in pigs. In this study, the enrofloxacin concentrations in plasma and tissues were detected using high-performance liquid chromatography with phosphate buffer (pH = 3) and acetonitrile. The pharmacokinetics and elimination of enrofloxacin enteric-coated granules were performed after oral administration at a single dose of 10 mg/kg body weight (bw) and 5 mg/kg twice per day for 5 consecutive days, respectively. The in vivo antibacterial efficacy and clinical effectiveness of enrofloxacin enteric-coated granules against APP and MS were assayed at 2.5, 5, 10 mg/kg, compared with tiamulin (8 mg/kg) based on establishment of APP and MS infection models. 56 APP strains were selected and tested for in vitro antibacterial activity of enrofloxacin enteric-coated granules. The main parameters of elimination half-life (t 1/2β ), T max , and area under the curve (AUC) were 14.99 ± 4.19, 3.99 ± 0.10, and 38.93 ± 1.52 μg h/ml, respectively, revealing that the enrofloxacin concentration remained high and with a sustainable distribution in plasma. Moreover, the analysis on the evaluation of enrofloxacin and ciprofloxacin in muscle, fat, liver and kidney showed that the recovery were more than 84% recovery in accordance with the veterinary drug residue guidelines of United States pharmacopeia, and the withdrawal periods were 4.28, 3.81, 4.84, and 3.51 days, respectively, suggesting that the withdrawal period was 5 d after oral administration of 5 mg/kg twice per day. The optimal dosage of enrofloxacin enteric-coated granules against APP and MS was 5 mg/kg, with over 90% efficacy, which was significantly different ( p enrofloxacin enteric-coated granules had significant potential for treating APP and MS

Statistical evaluation of tablet coating processes: influence of pan design and solvent type

Directory of Open Access Journals (Sweden)

Valdomero Pereira de Melo Junior

2010-12-01

Full Text Available Partially and fully perforated pan coaters are among the most relevant types of equipment currently used in the process of coating tablets. The goal of this study was to assess the performance differences among these types of equipment employing a factorial design. This statistical approach allowed the simultaneous study of the process variables and verification of interactions among them. The study included partially-perforated and fully-perforated pan coaters, aqueous and organic solvents, as well as hypromellose-based immediate-release coating. The dependent variables were process time, energy consumption, mean weight of tablets and process yield. For the tests, placebo tablets with a mean weight of 250 mg were produced, divided into eight lots of two kilograms each and coated in duplicate, using both partially perforated pan and fully perforated pan coaters. The results showed a significant difference between the type of equipment used (partially and fully perforated pan coaters with regard to process time and energy consumption, whereas no significant difference was identified for mean weight of the coated tablets and process yield.Entre os tipos de equipamentos de maior relevância utilizados atualmente no processo de revestimento de comprimidos estão os de tambor parcial e totalmente perfurados. A proposta desse trabalho foi avaliar as diferenças de desempenho entre esses equipamentos empregando projeto fatorial. Essa abordagem estatística possibilitou o estudo simultâneo das variáveis do processo, permitindo verificar interações entre elas. O trabalho incluiu equipamento com tambor parcialmente perfurado e totalmente perfurado, solventes aquoso e orgânico, assim como revestimento de liberação imediata à base de hipromelose. As variáveis dependentes ou respostas foram tempo de processo, consumo de energia, peso médio e rendimento do processo. Para os ensaios, foram produzidos comprimidos de placebo de 250 mg de peso m

Effect of Sampling Frequency for Real-Time Tablet Coating Monitoring Using Near Infrared Spectroscopy.

Science.gov (United States)

Igne, Benoît; Arai, Hiroaki; Drennen, James K; Anderson, Carl A

2016-09-01

While the sampling of pharmaceutical products typically follows well-defined protocols, the parameterization of spectroscopic methods and their associated sampling frequency is not standard. Whereas, for blending, the sampling frequency is limited by the nature of the process, in other processes, such as tablet film coating, practitioners must determine the best approach to collecting spectral data. The present article studied how sampling practices affected the interpretation of the results provided by a near-infrared spectroscopy method for the monitoring of tablet moisture and coating weight gain during a pan-coating experiment. Several coating runs were monitored with different sampling frequencies (with or without co-adds (also known as sub-samples)) and with spectral averaging corresponding to processing cycles (1 to 15 pan rotations). Beyond integrating the sensor into the equipment, the present work demonstrated that it is necessary to have a good sense of the underlying phenomena that have the potential to affect the quality of the signal. The effects of co-adds and averaging was significant with respect to the quality of the spectral data. However, the type of output obtained from a sampling method dictated the type of information that one can gain on the dynamics of a process. Thus, different sampling frequencies may be needed at different stages of process development. © The Author(s) 2016.

Clinical Efficacy and Residue Depletion of 10% Enrofloxacin Enteric-Coated Granules in Pigs

Directory of Open Access Journals (Sweden)

Zhixin Lei

2017-05-01

Full Text Available A new, more palatable formulation of 10% enrofloxacin enteric-coated granules was investigated to evaluate the pharmacokinetic effect in plasma, the residue elimination in tissues and the clinical efficacy against Actinobacillus pleuropneumonia (APP and Mycoplasam suis (MS in pigs. In this study, the enrofloxacin concentrations in plasma and tissues were detected using high-performance liquid chromatography with phosphate buffer (pH = 3 and acetonitrile. The pharmacokinetics and elimination of enrofloxacin enteric-coated granules were performed after oral administration at a single dose of 10 mg/kg body weight (bw and 5 mg/kg twice per day for 5 consecutive days, respectively. The in vivo antibacterial efficacy and clinical effectiveness of enrofloxacin enteric-coated granules against APP and MS were assayed at 2.5, 5, 10 mg/kg, compared with tiamulin (8 mg/kg based on establishment of APP and MS infection models. 56 APP strains were selected and tested for in vitro antibacterial activity of enrofloxacin enteric-coated granules. The main parameters of elimination half-life (t1/2β, Tmax, and area under the curve (AUC were 14.99 ± 4.19, 3.99 ± 0.10, and 38.93 ± 1.52 μg h/ml, respectively, revealing that the enrofloxacin concentration remained high and with a sustainable distribution in plasma. Moreover, the analysis on the evaluation of enrofloxacin and ciprofloxacin in muscle, fat, liver and kidney showed that the recovery were more than 84% recovery in accordance with the veterinary drug residue guidelines of United States pharmacopeia, and the withdrawal periods were 4.28, 3.81, 4.84, and 3.51 days, respectively, suggesting that the withdrawal period was 5 d after oral administration of 5 mg/kg twice per day. The optimal dosage of enrofloxacin enteric-coated granules against APP and MS was 5 mg/kg, with over 90% efficacy, which was significantly different (p < 0.05 to the 2.5 mg/kg group, but not to the 10 mg/kg group or the positive

Terahertz Technology: A Boon to Tablet Analysis

Science.gov (United States)

Wagh, M. P.; Sonawane, Y. H.; Joshi, O. U.

2009-01-01

The terahertz gap has a frequency ranges from ∼0.3 THz to ∼10 THz in the electromagnetic spectrum which is in between microwave and infrared. The terahertz radiations are invisible to naked eye. In comparison with x-ray they are intrinsically safe, non-destructive and non-invasive. Terahertz spectroscopy enables 3D imaging of structures and materials, and the measurement of the unique spectral fingerprints of chemical and physical forms. Terahertz radiations are produced by a dendrimer based high power terahertz source and spectroscopy technologies. It resolves many of the questions left unanswered by complementary techniques, such as optical imaging, Raman and infrared spectra. In the pharmaceutical industries it enables nondestructive, internal, chemical analysis of tablets, capsules, and other dosage forms. Tablet coatings are a major factor in drug bioavailability. Therefore tablet coatings integrity and uniformity are of crucial importance to quality. Terahertz imaging gives an unparalleled certainty about the integrity of tablet coatings and the matrix performance of tablet cores. This article demonstrates the potential of terahertz pulse imaging for the analysis of tablet coating thickness by illustrating the technique on tablets. PMID:20490288

Enteric-coated epichlorohydrin crosslinked dextran microspheres for site-specific delivery to colon.

Science.gov (United States)

Rai, Gopal; Yadav, Awesh K; Jain, Narendra K; Agrawal, Govind P

2015-01-01

Enteric-coated epichlorohydrin crosslinked dextran microspheres containing 5-Fluorouracil (5-FU) for colon drug delivery was prepared by emulsification-crosslinking method. The formulation variables studied includes different molecular weights of dextran, volume of crosslinking agent, stirring speed, time and temperature. Dextran microspheres showed mean entrapment efficiencies ranging between 77 and 87% and mean particle size ranging between 10 and 25 µm. About 90% of drug was released from uncoated dextran microspheres within 8 h, suggesting the fast release and indicated the drug loaded in uncoated microspheres, released before they reached colon. Enteric coating (Eudragit-S-100 and Eudragit-L-100) of dextran microspheres was performed by oil-in-oil solvent evaporation method. The release study of 5-FU from coated dextran microspheres was complete retardation in simulated gastric fluid (pH 1.2) and once the coating layer of enteric polymer was dissolved at higher pH (7.4 and 6.8), a controlled release of the drug from the microspheres was observed. Further, the release of drug was found to be higher in the presence of dextranase and rat caecal contents, indicating the susceptibility of dextran microspheres to colonic enzymes. Organ distribution and pharmacokinetic study in albino rats was performed to establish the targeting potential of optimized formulation in the colon.

A gamma scintigraphic study of gastric coating by Expidet, tablet and liquid formulations

International Nuclear Information System (INIS)

Washington, N.; Wilson, C.G.; Greaves, J.L.; Norman, S.

1989-01-01

The gastric residence time and gastric coating properties of 10 mg of radiolabelled micronised resin incorporated into Expidet formulations, chewable tablets and 10 ml of a liquid formulation were measued by gamma scintigraphy in twelve fasted, healthy subjects. All preparations emptied from the stomach in a similar manner for the first 1.5 h; however, the final 10% of the activity from the Expidet formulation emptied considerably more slowly than the initial phase. The total mean gastric emptying times for the three formulations were 2.3, 2.5 and 5.5 h for the tablet, liquid and Expidet formulation, respectively. The amount of activity following administration of the table or Expidet formulation was the same in the three regions of the stomach, but the coating of the mucosa by the Expidet formulation within each area was observed to be more uniform due to the greater dispersion of the dose form. The table broke up into a number of small discrete pieces. The gastric residence time of 99m Tc-labelled resin delivered in an Expidet formulation is significantly longer than the same marker administered in a table or in 10 ml of a liquid formulation. Moreover, coating of the gastric mucosa was more uniform with the Expidet formulation than the other two formulations studied. (author) 10 refs.; 6 figs

Mycophenolic acid agents: is enteric coating the answer?

Directory of Open Access Journals (Sweden)

Manitpisitkul W

2011-03-01

Full Text Available Wana Manitpisitkul1, Sabrina Lee2, Matthew Cooper31Department of Pharmacy, University of Maryland Medical Center, Baltimore, MD, USA; 2Solid Organ Transplant Program, University of Utah Health Care, Salt Lake City, UT, USA; 3Department of Surgery, University of Maryland School of Medicine, Baltimore, MD, USAAbstract: Addition of mycophenolate mofetil (MMF to calcineurin-based immunosuppressive therapy has led to a significant improvement in graft survival and reduction of acute rejection in renal transplant recipients. However, in clinical practice, MMF dose reduction, interruption, or discontinuation due to hematological and gastrointestinal (GI side-effects occurred in up to 50% of the patients. Large retrospective analyses have demonstrated that patients requiring MMF dose manipulation due to adverse events experienced a higher rate of rejection and graft loss. Enteric-coated mycophenolate sodium (EC-MPS was developed with the goal of improving upper GI side-effects. Here, we review the efficacy and safety of EC-MPS in de novo kidney transplant recipient, and in stable renal transplant patients who were converted from MMF. The changes in GI-related adverse events using patient-reported outcome instruments are also reviewed.Keywords: enteric-coated mycophenolate sodium, mycophenolate mofetil, kidney transplant, efficacy, gastrointestinal tolerability

Stabilization and target delivery of Nattokinase using compression coating.

Science.gov (United States)

Law, D; Zhang, Z

2007-05-01

The aim of the work is to develop a new formulation in order to stabilize a nutraceutical enzyme Nattokinase (NKCP) in powders and to control its release rate when it passes through the gastrointestinal tract of human. NKCP powders were first compacted into a tablet, which was then coated with a mixture of an enteric material Eudragit L100-55 (EL100-55) and Hydroxypropylcellulose (HPC) by direct compression. The activity of the enzyme was determined using amidolytic assay and its release rates in artificial gastric juice and an intestinal fluid were quantified using bicinchoninic acid assay. Results have shown that the activity of NKCP was pressure independent and the coated tablets protected NKCP from being denatured in the gastric juice, and realized its controlled release to the intestine based on in vitro experiments.

Development of a chitosan based double layer-coated tablet as a platform for colon-specific drug delivery

Directory of Open Access Journals (Sweden)

Kim MS

2016-12-01

Full Text Available Min Soo Kim,1,* Dong Woo Yeom,1,* Sung Rae Kim,1 Ho Yub Yoon,1 Chang Hyun Kim,1 Ho Yong Son,1 Jin Han Kim,1 Sangkil Lee,2 Young Wook Choi1 1College of Pharmacy, Chung-Ang University, Seoul, 2College of Pharmacy, Keimyung University, Daegu, South Korea *These authors contributed equally to this work Abstract: A double layer-coated colon-specific drug delivery system (DL-CDDS was developed, which consisted of chitosan (CTN based polymeric subcoating of the core tablet containing citric acid for microclimate acidification, followed by an enteric coating. The polymeric composition ratio of Eudragit E100 and ethyl cellulose and amount of subcoating were optimized using a two-level factorial design method. Drug-release characteristics in terms of dissolution efficiency and controlled-release duration were evaluated in various dissolution media, such as simulated colonic fluid in the presence or absence of CTNase. Microflora activation and a stepwise mechanism for drug release were postulated. Consequently, the optimized DL-CDDS showed drug release in a controlled manner by inhibiting drug release in the stomach and intestine, but releasing the drug gradually in the colon (approximately 40% at 10 hours and 92% at 24 hours in CTNase-supplemented simulated colonic fluid, indicating its feasibility as a novel platform for CDD. Keywords: chitosan, colon-specific delivery, acidification, microflora, factorial design, controlled release

Broadband Acoustic Resonance Dissolution Spectroscopy (BARDS): A rapid test for enteric coating thickness and integrity of controlled release pellet formulations.

Science.gov (United States)

Alfarsi, Anas; Dillon, Amy; McSweeney, Seán; Krüse, Jacob; Griffin, Brendan; Devine, Ken; Sherry, Patricia; Henken, Stephan; Fitzpatrick, Stephen; Fitzpatrick, Dara

2018-04-12

There are no rapid dissolution based tests for determining coating thickness, integrity and drug concentration in controlled release pellets either during production or post-production. The manufacture of pellets requires several coating steps depending on the formulation. The sub-coating and enteric coating steps typically take up to six hours each followed by additional drying steps. Post production regulatory dissolution testing also takes up to six hours to determine if the batch can be released for commercial sale. The thickness of the enteric coating is a key factor that determines the release rate of the drug in the gastro-intestinal tract. Also, the amount of drug per unit mass decreases with increasing thickness of the enteric coating. In this study, the coating process is tracked from start to finish on an hourly basis by taking samples of pellets during production and testing those using BARDS (Broadband Acoustic Resonance Dissolution Spectroscopy). BARDS offers a rapid approach to characterising enteric coatings with measurements based on reproducible changes in the compressibility of a solvent due to the evolution of air during dissolution. This is monitored acoustically via associated changes in the frequency of induced acoustic resonances. A steady state acoustic lag time is associated with the disintegration of the enteric coatings in basic solution. This lag time is pH dependent and is indicative of the rate at which the coating layer dissolves. BARDS represents a possible future surrogate test for conventional USP dissolution testing as its data correlates directly with the thickness of the enteric coating, its integrity and also with the drug loading as validated by HPLC. Copyright © 2018 Elsevier B.V. All rights reserved.

Floating tablets for controlled release of ofloxacin via compression coating of hydroxypropyl cellulose combined with effervescent agent.

Science.gov (United States)

Qi, Xiaole; Chen, Haiyan; Rui, Yao; Yang, Fengjiao; Ma, Ning; Wu, Zhenghong

2015-07-15

To prolong the residence time of dosage forms within gastrointestinal trace until all drug released at desired rate was one of the real challenges for oral controlled-release drug delivery system. Herein, we developed a fine floating tablet via compression coating of hydrophilic polymer (hydroxypropyl cellulose) combined with effervescent agent (sodium bicarbonate) to achieve simultaneous control of release rate and location of ofloxacin. Sodium alginate was also added in the coating layer to regulate the drug release rate. The effects of the weight ratio of drug and the viscosity of HPC on the release profile were investigated. The optimized formulations were found to immediately float within 30s and remain lastingly buoyant over a period of 12 h in simulated gastric fluid (SGF, pH 1.2) without pepsin, indicating a satisfactory floating and zero-order drug release profile. In addition, the oral bioavailability experiment in New Zealand rabbits showed that, the relative bioavailability of the ofloxacin after administrated of floating tablets was 172.19%, compared to marketed common release tablets TaiLiBiTuo(®). These results demonstrated that those controlled-released floating tables would be a promising gastro-retentive delivery system for drugs acting in stomach. Copyright © 2015 Elsevier B.V. All rights reserved.

Development of an automation system for a tablet coater

DEFF Research Database (Denmark)

Ruotsalainen, Mirja; Heinämäki, Jyrki; Rantanen, Jukka

2002-01-01

An instrumentation and automation system for a side-vented pan coater with a novel air-flow rate measurement system for monitoring the film-coating process of tablets was designed and tested. The instrumented coating system was tested and validated by film-coating over 20 pilot-scale batches...... and automated pan-coating system described, including historical data storage capability and a novel air-flow measurement system, is a useful tool for controlling and characterizing the tablet film-coating process. Monitoring of critical process parameters increases the overall coating process efficiency...

Enteric-coated sustained-release nanoparticles by coaxial electrospray: preparation, characterization, and in vitro evaluation

Science.gov (United States)

Hao, Shilei; Wang, Bochu; Wang, Yazhou; Xu, Yingqian

2014-02-01

Enteric-coated formulations can delay the release of drugs until they have passed through the stomach. However, high concentration of drugs caused by rapidly released in the small intestine leads to the intestinal damage, and frequent administration would increase the probability of missing medication and reduce the patient compliance. To solve the above-mentioned problems, aspirin-loaded enteric-coated sustained-release nanoparticles with core-shell structure were prepared via one-step method using coaxial electrospray in this study. Eudragit L100-55 as pH-sensitive polymer and Eudragit RS as sustained-release polymer were used for the outer coating and inner core of the nanoparticles, respectively. The maximum loading capacity of nanoparticles was 23.66 % by changing the flow rate ratio of outer/inner solutions, and the entrapment efficiency was nearly 100 %. Nanoparticles with core-shell structure were observed via fluorescence microscope and transmission electron microscope. And pH-sensitive and sustained drug release profiles were observed in the media with different pH values (1.2 and 6.8). In addition, mild cytotoxicity in vitro was detected, and the nanoparticles could be taken up by Caco-2 cells within 1.0 h in cellular uptake study. These results indicate that prepared enteric-coated sustained-release nanoparticles would be a more safety and effective carrier for oral drug delivery.

Iodine tablets and a nuclear accident

International Nuclear Information System (INIS)

Paile, W.

1992-01-01

Radioactive iodine is one of the major substances released during severe nuclear accidents. Radioactive iodine is easily gasified, and if present in fallout it can enter the lungs, and thereby the circulatory system, with the inhalation of air. Once in a body, radioactive iodine accumulates in the thyroid and may result in tumours in the thyroid and, in extreme cases, impaired thyroid function. Accumulation of radioactive iodine can be prevented by taking non-radioactive, 'cold' iodine as tablets. Iodine tablets dilute the radioactive iodine that has entered the body. A dose of iodine also paralyses the thyroid temporarily by saturating its iodine-carrying capacity. To be useful iodine tablets should be taken immediately when a radioactive emission has occurred. If the tablets are taken too early or too late, they give little protection. Iodine tablets should not be taken just to be on the safe side, since their use may involve harmful side effects. Dosing instructions should also be followed with care. (orig.)

Formulation of Dihydroartemisinin-Piperaquine (DHP Generic Tablet as Antimalarials Drug

Directory of Open Access Journals (Sweden)

Nanang Yunarto

2016-09-01

Full Text Available The incidence of malaria in Indonesia is about two million cases annually. Dihydroartemisinin-piperaquine (DHP is the first line therapy recommended for uncomplicated malaria treatment, whereas  DHP is still fully imported. The generic DHP tablet formulation has the potential to become the first of DHP drug which is locally produced. This study is aimed to formulate generic DHP film coated tablets for antimalaria drug. Tablets were compressed with the combination of wet granulation for piperaquine phosphate (PQP and direct compression method for DHA and coated with a moisture barier coating material. The parameters to evaluate the quality of DHP tablets are physical properties, assay, and dissolution test. DHA and PQP assay were performed by HPLC method. The dissolution testing was conducted by in house method using HCl 0.1 N medium. The result shows physical properties of film-coated tablets meet the requirement, i.e. uniform weight, 7.0-8.5 kp hardness, 0.02% friability and 3 minute 22 seconds disintegration. The assay to determine  DHA in tablet was 95.17% and PQP was 97.05%. The result of dissolution testing shows the content of DHA and PQP in the tablet were 113.51% and 96.55%, respesctively. The formulation which is developed meets the general requirement of API in tablet 90–110% and dissolution requirement >75%.

The Formulation of Diclofenac Sodium Hydrogel Tablets | Onyechi ...

African Journals Online (AJOL)

The dissolution data fitted to Higuchi and Hixson-Crowell equations indicating the existence of diffusion mechanism controlling diclofenac release from the tablets. Keywords: Sustained release, diclofenac sodium hydrogel tablets, Voltarol retard tablets, film coating, dissolution profiles. Nigerian Journal of Pharmaceutical ...

Substantial reduction of inappropriate tablet splitting with computerised decision support: a prospective intervention study assessing potential benefit and harm

Directory of Open Access Journals (Sweden)

Quinzler Renate

2009-06-01

Full Text Available Abstract Background Currently ambulatory patients break one in four tablets before ingestion. Roughly 10% of them are not suitable for splitting because they lack score lines or because enteric or modified release coating is destroyed impairing safety and effectiveness of the medication. We assessed impact and safety of computerised decision support on the inappropriate prescription of split tablets. Methods We performed a prospective intervention study in a 1680-bed university hospital. Over a 15-week period we evaluated all electronically composed medication regimens and determined the fraction of tablets and capsules that demanded inappropriate splitting. In a subsequent intervention phase of 15 weeks duration for 10553 oral drugs divisibility characteristics were indicated in the system. In addition, an alert was generated and displayed during the prescription process whenever the entered dosage regimen demanded inappropriate splitting (splitting of capsules, unscored tablets, or scored tablets unsuitable for the intended fragmentation. Results During the baseline period 12.5% of all drugs required splitting and 2.7% of all drugs (257/9545 required inappropriate splitting. During the intervention period the frequency of inappropriate splitting was significantly reduced (1.4% of all drugs (146/10486; p = 0.0008. In response to half of the alerts (69/136 physicians adjusted the medication regimen. In the other half (67/136 no corrections were made although a switch to more suitable drugs (scored tablets, tablets with lower strength, liquid formulation was possible in 82% (55/67. Conclusion This study revealed that computerised decision support can immediately reduce the frequency of inappropriate splitting without introducing new safety hazards.

Enteric-coated mycophenolate sodium.

Science.gov (United States)

Gabardi, Steven; Tran, Jennifer L; Clarkson, Michael R

2003-11-01

To review the pharmacology, pharmacokinetics, efficacy, and safety of mycophenolate sodium. Primary literature was obtained via a MEDLINE search (1966-June 2003). Abstracts were obtained from the manufacturer and included in the analysis. All studies and abstracts evaluating mycophenolate sodium in solid organ transplantation were considered for inclusion. English-language studies and abstracts were selected for inclusion, but were limited to those consisting of human subjects. Mycophenolate sodium, a mycophenolic acid prodrug, is an inhibitor of T-lymphocyte proliferation. Mycophenolic acid reduces the incidence of acute rejection in renal transplantation. Mycophenolate sodium is enteric coated and has been suggested as a potential method to reduce the gastrointestinal adverse events seen with mycophenolate mofetil. Both mycophenolate mofetil and mycophenolate sodium have been shown to be therapeutically equivalent at decreasing the incidence of allograft rejection and loss. The frequency of adverse events is similar between both compounds, with the most common events being diarrhea and leukopenia. Mycophenolate sodium is effective in preventing acute rejection in renal transplant recipients. At doses of 720 mg twice daily, the efficacy and safety profiles are similar to those of mycophenolate mofetil 1000 mg twice daily. Mycophenolate sodium has been approved in Switzerland; approval in the US is pending.

Molecular insights into shellac film coats from different aqueous shellac salt solutions and effect on disintegration of enteric-coated soft gelatin capsules.

Science.gov (United States)

Al-Gousous, J; Penning, M; Langguth, P

2015-04-30

The purpose of this investigation was to study the effect of using different salts of shellac on the disintegration properties of shellac-based enteric coatings. In the last two decades, shellac has been increasingly used as an aqueous solution for enteric coating purposes, with the ammonium salt being the form typically used. Little investigation has been performed on using other salts, and therefore, this was the focus of our work. Enteric coatings, based on different shellac salts (ammonium, sodium, potassium and composite ammonium-sodium), were applied onto soft gelatin capsules. Disintegration testing of the coated soft gelatin capsules showed that alkali metal salts promote faster disintegration than ammonium salts. In order to determine the causes behind these differences, the solubility, thermal and spectroscopic properties of films cast from the different salts were investigated. The results show that films cast from ammonium-based salts of shellac are, unlike those cast from alkali metal-based salts, water-insoluble. Spectroscopic evidence suggests that this might be due to partial salt dissociation resulting in loss of ammonium as ammonia and reduced degree of shellac ionization during drying. In addition, oxidation of shellac aldehyde groups of the ammonium-based shellac salts could also play a role. And possible higher extent of shellac hydrolysis during the preparation of alkali metal salts might also be a factor. Therefore, the nature of the shellac salt used in the preparation of shellac-based aqueous coating solutions is a significant formulation factor affecting product performance. Copyright © 2014 Elsevier B.V. All rights reserved.

Desarrollo de una formulación de tabletas revestidas de secnidazol 500 mg Development of a formulation of coated secnidazole tablets 500 mg

Directory of Open Access Journals (Sweden)

Iverlis Díaz Polanco

2008-04-01

Full Text Available Se describe el desarrollo de una formulación de tabletas revestidas de secnidazol 500 mg. Durante el desarrollo de esta se evaluaron 2 métodos: la granulación seca y la granulación húmeda. En el revestimiento de las tabletas se empleó un sistema hidroalcohólico con el preparado comercial Policoat YS 1-7003 (Opadry®. Los lotes sometidos a ensayos de estabilidad fueron elaborados a escala piloto, por la vía de granulación húmeda, lo que demostró la factibilidad del proceso de fabricación a esta escala. Las tabletas revestidas presentaron adecuadas propiedades físico-mecánicas y tecnológicas y estas fueron envasadas en frascos de polietileno de alta densidad y en sobres termoconformados de polivinilcloruro/aluminio. La estabilidad química y microbiológica de las tabletas de secnidazol fue estudiada durante 24 meses; los resultados demostraron que estas cumplían con los requisitos establecidos durante este periodoThe development of a formulation of coated Secnidazole tablets 500mg was described. During its development, 2 methods were evaluated: dry granulation and humid granulation. A hydroalcoholic system was used with the Policoat YS 1-7003 (Opadry® commercial preparation for coating the tablets. The batches subjected to stability assays were made at pilot scale by humid granulation, which showed the feasibility of the manufacturing process at this scale. The coated tablets had adequate physicomechanical and technological properties and they were packed in polyethylene flasks of high density and in polyvinyl chloride/aluminium thermoconformed envelopes. The chemical and microbiological stability of the secnidazole tablets were studied during 24 months. The results demonstrated that these tablets met the requirements established during this period

Pharmacokinetics of colon-specific pH and time-dependent flurbiprofen tablets.

Science.gov (United States)

Vemula, Sateesh Kumar; Veerareddy, Prabhakar Reddy; Devadasu, Venkat Ratnam

2015-09-01

Present research deals with the development of compression-coated flurbiprofen colon-targeted tablets to retard the drug release in the upper gastro intestinal system, but progressively release the drug in the colon. Flurbiprofen core tablets were prepared by direct compression method and were compression coated using sodium alginate and Eudragit S100. The formulation is optimized based on the in vitro drug release study and further evaluated by X-ray imaging and pharmacokinetic studies in healthy humans for colonic delivery. The optimized formulation showed negligible drug release (4.33 ± 0.06 %) in the initial lag period followed by progressive release (100.78 ± 0.64 %) for 24 h. The X-ray imaging in human volunteers showed that the tablets reached the colon without disintegrating in the upper gastrointestinal tract. The C max of colon-targeted tablets was 12,374.67 ng/ml at T max 10 h, where as in case of immediate release tablets the C max was 15,677.52 ng/ml at T max 3 h, that signifies the ability of compression-coated tablets to target the colon. Development of compression-coated tablets using combination of time-dependent and pH-sensitive approaches was suitable to target the flurbiprofen to colon.

Comparative effects of enteric-coated pancreatin microsphere therapy after conventional and pylorus-preserving pancreatoduodenectomy

NARCIS (Netherlands)

Bruno, M. J.; Borm, J. J.; Hoek, F. J.; Delzenne, B.; Hofmann, A. F.; de Goeij, J. J.; van Royen, E. A.; van Gulik, T. M.; de Wit, L. T.; Gouma, D. J.; van Leeuwen, D. J.; Tytgat, G. N.

1997-01-01

BACKGROUND: A comparative study was performed between patients with exocrine pancreatic insufficiency after conventional pancreatoduodenectomy (Whipple's procedure) and pylorus-preserving pancreatoduodenectomy (PPPD). In these patients the pharmacodynamics of 2-mm enteric-coated pancreatin

Construction of a novel pH-sensitive drug release system from mesoporous silica tablets coated with Eudragit

Science.gov (United States)

Xu, Yingpu; Qu, Fengyu; Wang, Yu; Lin, Huiming; Wu, Xiang; Jin, Yingxue

2011-03-01

A novel pH-sensitive drug release system has been established by coating Eudragit (Eud) on drug-loaded mesoporous silica (MS) tablets. The release rate of ibuprofen (IBU) from the MS was retarded by coating with Eudragit S-100, and the higher retardation was due to the increase of coating concentration and the coating layers. The target position of the release depended on the pH of the release medium, which was confirmed by the drug release from IBU/MS/Eud increasing rapidly with the change of medium pH from 1.2 to 7.4. This drug delivery system could prohibit irritant drug from leaking in the stomach and make it only release in the intestine. The loaded and unloaded drug samples were characterized by powder X-ray diffraction (XRD), Fourier transform infrared spectrometer (FTIR), N 2 adsorption/desorption, scanning electron microscopy (SEM), and transmission electron microscopy (TEM).

Pharmaceutical equivalence of gabapentin tablets with various extragranular binders Pharmaceutical equivalence of gabapentin tablets with various extragranular binders

Directory of Open Access Journals (Sweden)

SWATI C. JAGDALE

2010-06-01

Full Text Available Gabapentin is a high-dose drug widely used as an oral anti-epilepticagent. Due to high crystalline and has poor compaction properties it is difficult to form tablets by direct compression. The aim of this study was to develop gabapentin tablets, pharmaceutically equivalent to the reference product Neurontin (marketed in USA. Gabapentin 800mg tablets were produced by wet granulation by keeping intragranular binder as well as its concentration constant and by changing with various extragranular binders with its concentration (A = PVPK 30, B = HPMC 15 cps, C = Kollidon VA 64, D =Klucel EXF.The tablet having no weight, thickness and hardness variation and having appropriate, friability as well as disintegration profile were coated with a 3% film coating solution .Seven formulations F1 (A in lower concentration F2 (A in higher concentration, F3 (B in lower concentration and F4 (B in higher concentration, F5 (C in lower concentration, F6 (C in higher concentration, F7 (D in lower concentration were formulated. Among them F6 demonstrated adequate hardness, friability, disintegration, uniformity of content, and total drug dissolution after 45minutes. The dissimilarity factor (f1 is 5.93 and the similarity factor (f2 is 67.85. So F6 was found to be equivalent to Neurontin.Gabapentin is widely used as an oral anti-epileptic agent. However, owing to its high crystallinity and poor compaction properties, it is difficult to form tablets of this drug by direct compression. The aim of this study was to develop gabapentin tablets, pharmaceutically equivalent to the brand-name pioneer product Neurontin® (marketed in USA. Gabapentin 800mg tablets were produced by wet granulation with a constant concentration of intragranular binder and a varying concentration of extragranular binders (A = polyvinylpyrrolidone K30, B = hydroxypropylmethylcellulose 15 cps, C = Kollidon VA64, D =Klucel EXF. The tablets that did not vary in weight, thickness or hardness and had

Assessing gastrointestinal motility and disintegration profiles of magnetic tablets by a novel magnetic imaging device and gamma scintigraphy.

Science.gov (United States)

Goodman, Kirsteen; Hodges, Lee Ann; Band, Janet; Stevens, Howard N E; Weitschies, Werner; Wilson, Clive G

2010-01-01

To validate Magnetic Moment Imaging (MMI) for the investigation of gastrointestinal transit and disintegration of solid dosage forms and to correlate the MMI findings with the corresponding gamma scintigraphic data. Three magnetic tablets (MTs) were investigated using in vitro and in vivo tests. The clinical study was a four-way, crossover study with the following arms: (a) immediate-release tablets administered in fasted state; (b) immediate-release tablets administered after 400mL of Clinutren ISO; (c) enteric-coated tablets administered in the fasted state; and (d) non-disintegrating tablets studied in the lightly fed state (100mL of Clinutren ISO). In both the in vitro and in vivo studies, tablets were detected successfully by MMI and scintigraphy. There was a good correlation between gastric residence times and positional data (in the x, y and y, z-axes). In addition, MMI revealed early swelling behaviour of the tablet matrix. There was excellent agreement for the disintegration times of MT(A) in the fasted arm (scintigraphy 12.0+/-4.4min, MMI 11.8+/-4.4min). In the MT(A)-fed arm, onset times determined by scintigraphy were delayed in three subjects when compared to the corresponding MMI results. Delayed disintegration was observed with MT(A) administered after food (pdisintegration of a magnetic tablet through the gastrointestinal tract. Copyright 2009 Elsevier B.V. All rights reserved.

Key Technical Aspects Influencing the Accuracy of Tablet Subdivision.

Science.gov (United States)

Teixeira, Maíra T; Sá-Barreto, Lívia C L; Gratieri, Taís; Gelfuso, Guilherme M; Silva, Izabel C R; Cunha-Filho, Marcílio S S

2017-05-01

Tablet subdivision is a common practice used mainly for dose adjustment. The aim of this study was to investigate how the technical aspects of production as well as the method of tablets subdivision (employing a tablet splitter or a kitchen knife) influence the accuracy of this practice. Five drugs commonly used as subdivided tablets were selected. For each drug, the innovator drug product, a scored-generic and a non-scored generic were investigated totalizing fifteen drug products. Mechanical and physical tests, including image analysis, were performed. Additionally, comparisons were made between tablet subdivision method, score, shape, diluent composition and coating. Image analysis based on surface area was a useful tool as an alternative assay to evaluate the accuracy of tablet subdivision. The tablet splitter demonstrates an advantage relative to a knife as it showed better results in weight loss and friability tests. Oblong, coated and scored tablets had better results after subdivision than round, uncoated and non-scored tablets. The presence of elastic diluents such as starch and dibasic phosphate dehydrate conferred a more appropriate behaviour for the subdivision process than plastic materials such as microcrystalline cellulose and lactose. Finally, differences were observed between generics and their innovator products in all selected drugs with regard the quality control assays in divided tablet, which highlights the necessity of health regulations to consider subdivision performance at least in marketing authorization of generic products.

Studies on portal systemic circulation by oral administration of 201Tl enclosed enteric coated capsule

International Nuclear Information System (INIS)

Tonami, Norihisa; Nakajima, Kenichi; Watanabe, Naoto

1986-01-01

Thallium-201 enclosed enteric coated capsule was prepared and administered orally to evaluate portal systemic circulation in 11 control subjects and 31 patients with various liver diseases by investigating scintigraphic appearance and the heart-to-liver uptake ratio (H/L ratio). In 10 patients with liver cirrhosis and one with chronic hepatitis, the results of H/L ratio were compared to those obtained by 201 Tl per-rectal administration. 1. It was fundamentally confirmed that 201 Tl enclosed enteric coated capsule was not broken down in the artificial gastric juice, but nearly completely melted 15 minutes after soaking in the artificial intestinal juice. 2. Clinical study was successfully completed in 36 out of 42 cases (86 %). Unsuccessful cases were found in 2 with capsule collapse in the stomach and 4 with its poor moving to the duodenum. 3. In control subjects the liver was clearly visualized and the mean value of H/L ratio was 0.32 which is lower than that of 201 Tl per-rectal administration previously reported. H/L ratio in patients with chronic and acute hepatitis was nearly equal to that in control subjects. H/L ratio in patients with liver cirrhosis was slightly higher than that in control subjects, but there was no significant difference between them. In cases with esophageal varices, H/L ratio was not so high compared to that in control subjects. Out of 7 patients showing high H/L ratio more than 0.8 in 201 Tl per-rectal administration, only one showed similar high ratio (1.07) in oral administration of 201 Tl enclosed enteric coated capsule. In this case the shunting from superior mesenteric vein to inferior vena cava connection was confirmed. From these results, it was considered that the shunting volume of superior mesenteric vein through esophageal varices is small. 4. A possibility of a new administration of radioisotope with enteric coated capsule was emphasized. (author)

Impact of salt form and molecular weight of chitosan on swelling and drug release from chitosan matrix tablets.

Science.gov (United States)

Huanbutta, Kampanart; Cheewatanakornkool, Kamonrak; Terada, Katsuhide; Nunthanid, Jurairat; Sriamornsak, Pornsak

2013-08-14

Magnetic resonance imaging (MRI) and gravimetric techniques were used to assess swelling and erosion behaviors of hydrophilic matrix tablets made of chitosan. The impact of salt form, molecular weight (MW) and dissolution medium on swelling behavior and drug (theophylline) release was studied. The matrix tablets made of chitosan glycolate (CGY) showed the greatest swelling in both acid and neutral media, compared to chitosan aspartate, chitosan glutamate and chitosan lactate. MRI illustrated that swelling region of CGY in both media was not different in the first 100 min but glassy region (dry core) in 0.1N HCl was less than in pH 6.8 buffer. The tablets prepared from chitosan with high MW swelled greater than those of low MW. Moreover, CGY can delay drug release in the acid condition due to thick swollen gel and low erosion rate. Therefore, CGY may be suitably applied as sustained drug release polymer or enteric coating material. Copyright © 2013 Elsevier Ltd. All rights reserved.

Authentication of gold nanoparticle encoded pharmaceutical tablets using polarimetric signatures.

Science.gov (United States)

Carnicer, Artur; Arteaga, Oriol; Suñé-Negre, Josep M; Javidi, Bahram

2016-10-01

The counterfeiting of pharmaceutical products represents concerns for both industry and the safety of the general public. Falsification produces losses to companies and poses health risks for patients. In order to detect fake pharmaceutical tablets, we propose producing film-coated tablets with gold nanoparticle encoding. These coated tablets contain unique polarimetric signatures. We present experiments to show that ellipsometric optical techniques, in combination with machine learning algorithms, can be used to distinguish genuine and fake samples. To the best of our knowledge, this is the first report using gold nanoparticles encoded with optical polarimetric classifiers to prevent the counterfeiting of pharmaceutical products.

Development and optimization of enteric coated mucoadhesive microspheres of duloxetine hydrochloride using 32 full factorial design

Science.gov (United States)

Setia, Anupama; Kansal, Sahil; Goyal, Naveen

2013-01-01

Background: Microspheres constitute an important part of oral drug delivery system by virtue of their small size and efficient carrier capacity. However, the success of these microspheres is limited due to their short residence time at the site of absorption. Objective: The objective of the present study was to formulate and systematically evaluate in vitro performance of enteric coated mucoadhesive microspheres of duloxetine hydrochloride (DLX), an acid labile drug. Materials and Methods: DLX microspheres were prepared by simple emulsification phase separation technique using chitosan as carrier and glutaraldehyde as a cross-linking agent. Microspheres prepared were coated with eudragit L-100 using an oil-in-oil solvent evaporation method. Eudragit L-100was used as enteric coating polymer with the aim to release the drug in small intestine The microspheres prepared were characterized by particle size, entrapment efficiency, swelling index (SI), mucoadhesion time, in vitro drug release and surface morphology. A 32 full factorial design was employed to study the effect of independent variables polymer-to-drug ratio (X1) and stirring speed (X2) on dependent variables, particle size, entrapment efficiency, SI, in vitro mucoadhesion and drug release up to 24 h (t24). Results: Microspheres formed were discrete, spherical and free flowing. The microspheres exhibited good mucoadhesive property and also showed high percentage entrapment efficiency. The microspheres were able to sustain the drug release up to 24 h. Conclusion: Thus, the prepared enteric coated mucoadhesive microspheres may prove to be a potential controlled release formulation of DLX for oral administration. PMID:24167786

Development and optimization of enteric coated mucoadhesive microspheres of duloxetine hydrochloride using 3(2) full factorial design.

Science.gov (United States)

Setia, Anupama; Kansal, Sahil; Goyal, Naveen

2013-07-01

Microspheres constitute an important part of oral drug delivery system by virtue of their small size and efficient carrier capacity. However, the success of these microspheres is limited due to their short residence time at the site of absorption. The objective of the present study was to formulate and systematically evaluate in vitro performance of enteric coated mucoadhesive microspheres of duloxetine hydrochloride (DLX), an acid labile drug. DLX microspheres were prepared by simple emulsification phase separation technique using chitosan as carrier and glutaraldehyde as a cross-linking agent. Microspheres prepared were coated with eudragit L-100 using an oil-in-oil solvent evaporation method. Eudragit L-100was used as enteric coating polymer with the aim to release the drug in small intestine The microspheres prepared were characterized by particle size, entrapment efficiency, swelling index (SI), mucoadhesion time, in vitro drug release and surface morphology. A 3(2) full factorial design was employed to study the effect of independent variables polymer-to-drug ratio (X1) and stirring speed (X2) on dependent variables, particle size, entrapment efficiency, SI, in vitro mucoadhesion and drug release up to 24 h (t24). Microspheres formed were discrete, spherical and free flowing. The microspheres exhibited good mucoadhesive property and also showed high percentage entrapment efficiency. The microspheres were able to sustain the drug release up to 24 h. Thus, the prepared enteric coated mucoadhesive microspheres may prove to be a potential controlled release formulation of DLX for oral administration.

Studies on portal systemic circulation by oral administration of /sup 201/Tl enclosed enteric coated capsule

Energy Technology Data Exchange (ETDEWEB)

Tonami, Norihisa; Nakajima, Kenichi; Watanabe, Naoto and others

1986-03-01

Thallium-201 enclosed enteric coated capsule was prepared and administered orally to evaluate portal systemic circulation in 11 control subjects and 31 patients with various liver diseases by investigating scintigraphic appearance and the heart-to-liver uptake ratio (H/L ratio). In 10 patients with liver cirrhosis and one with chronic hepatitis, the results of H/L ratio were compared to those obtained by /sup 201/Tl per-rectal administration. 1. It was fundamentally confirmed that /sup 201/Tl enclosed enteric coated capsule was not broken down in the artificial gastric juice, but nearly completely melted 15 minutes after soaking in the artificial intestinal juice. 2. Clinical study was successfully completed in 36 out of 42 cases (86 %). Unsuccessful cases were found in 2 with capsule collapse in the stomach and 4 with its poor moving to the duodenum. 3. In control subjects the liver was clearly visualized and the mean value of H/L ratio was 0.32 which is lower than that of /sup 201/Tl per-rectal administration previously reported. H/L ratio in patients with chronic and acute hepatitis was nearly equal to that in control subjects. H/L ratio in patients with liver cirrhosis was slightly higher than that in control subjects, but there was no significant difference between them. In cases with esophageal varices, H/L ratio was not so high compared to that in control subjects. Out of 7 patients showing high H/L ratio more than 0.8 in /sup 201/Tl per-rectal administration, only one showed similar high ratio (1.07) in oral administration of /sup 201/Tl enclosed enteric coated capsule. In this case the shunting from superior mesenteric vein to inferior vena cava connection was confirmed. From these results, it was considered that the shunting volume of superior mesenteric vein through esophageal varices is small. 4. A possibility of a new administration of radioisotope with enteric coated capsule was emphasized.

Formulation and evaluation of sustained release matrix tablet of rabeprazole using wet granulation technique

Directory of Open Access Journals (Sweden)

Ruqaiyah Khan

2014-01-01

Full Text Available Introduction: Rabeprazole, a member of substituted benzimidazoles, inhibits the final step in gastric acid secretions. This drug claims to cause fastest acid separation (due to higher pKa, and more rapidly converts to the active species to aid gastric mucin synthesis. The most significant pharmacological action of Rabeprazole is dose dependent suppression of gastric acid secretion; without anticholinergic or H2-blocking action. It completely abolishes the hydrochloric acid secretion as it is powerful inhibitor of gastric acid. Rabeprazole is acid labile and hence commonly formulated as an enteric coated tablet. The absorption of rabeprazole occurs rapidly as soon as tablet leaves the stomach. Aim: In the present study an attempt was made to formulate and evaluate Rabeprazole sustained release matrix tablet using wet granulation technique incorporating various polymers like HPMC-E15, Carbopol934, and sodium carboxymethyl cellulose (CMC. Materials and Methods: The Formulated tablets were evaluated for different physicochemical properties like rheological properties, weight variation, thickness, hardness, % friability, in vitro release studies and drug content. Results: Studies revealed that all the physicochemical parameters comply with the official standards. The in vitro release studies exhibits the release up to 90%, over a prolonged period of time which confirms the extended release profile of formulation, having better bioavailability as well as decreased dosing frequency with reduced doses. Conclusion: The sustained release matrix tablets of rabiprazole shown better bioavailability, efficacy and potency, when compared with official standards.

Effect of Coating Solvent Ratio on the Drug Release Lag Time of ...

African Journals Online (AJOL)

Erah

Research Article ... Lag Time of Coated Theophylline Osmotic Tablets ... Key words: Coating solvent, Drug release, Lag time, Osmotic tablet, HPMC, .... following composition (w/w): theophylline ... tablets was measured by UV absorption.

Multiple-unit tablet of probiotic bacteria for improved storage stability, acid tolerability, and in vivo intestinal protective effect

Directory of Open Access Journals (Sweden)

Park HJ

2016-04-01

Full Text Available Hee Jun Park,1 Ga Hyeon Lee,1 Joonho Jun,1 Miwon Son,1 Myung Joo Kang2 1Dong-A Pharmaceutical Co. Ltd., Yongin, Gyeonggi, 2College of Pharmacy, Dankook University, Cheonan, Chungnam, Korea Abstract: The aim of this study was to formulate probiotics-loaded pellets in a tablet form to improve storage stability, acid tolerability, and in vivo intestinal protective effect. Bacteria-loaded pellets primarily prepared with hydroxypropyl methylcellulose acetate succinate were compressed into tablets with highly compressible excipients and optimized for flow properties, hardness, and disintegration time. The optimized probiotic tablet consisted of enteric-coated pellets (335 mg, microcrystalline cellulose (Avicel PH102, 37.5 mg, and porous calcium silicate (25 mg and allowed whole survival of living bacteria during the compaction process with sufficient tablet hardness (13 kp and disintegration time (14 minutes. The multiple-unit tablet showed remarkably higher storage stability under ambient conditions (25°C/60% relative humidity over 6 months and resistance to acidic medium compared to uncoated strains or pellets. Repeated intake of this multiple-unit tablet significantly lowered plasma level of endotoxin, a pathogenic material, compared to repeated intake of bare probiotics or marketed products in rats. These results, therefore, suggest that the multiple-unit tablet is advantageous to better bacterial viability and gain the beneficial effects on the gut flora, including the improvement of intestinal barrier function. Keywords: probiotics, multiple-unit tablet, bacterial viability, acid resistance, intestinal barrier function

Mini-tablets versus pellets as promising multiparticulate modified release delivery systems for highly soluble drugs.

Science.gov (United States)

Gaber, Dina M; Nafee, Noha; Abdallah, Osama Y

2015-07-05

Whether mini-tablets (tablets, diameters ≤6mm) belong to single- or multiple-unit dosage forms is still questionable. Accordingly, Pharmacopoeial evaluation procedures for mini-tablets are lacking. In this study, the aforementioned points were discussed. Moreover, their potential for oral controlled delivery was assessed. The antidepressant venlafaxine hydrochloride (Vx), a highly soluble drug undergoing first pass effect, low bioavailability and short half-life was selected as a challenging payload. In an attempt to weigh up mini-tablets versus pellets as multiparticulate carriers, Vx-loaded mini-tablets were compared to formulated pellets of the same composition and the innovator Effexor(®)XR pellets. Formulations were prepared using various polymer hydrogels in the core and ethyl cellulose film coating with increasing thickness. Mini-tablets (diameter 2mm) showed extended Vx release (<60%, 8h). Indeed, release profiles comparable to Effexor(®)XR pellets were obtained. Remarkably higher coating thickness was required for pellets to provide equivalent retardation. Ethyl cellulose in the core ensured faster release due to polymer migration to the surface and pore formation in the coat. mini-tablets showed higher stability to pellets upon storage. Industrially speaking, mini-tablets proved to be superior to pellets in terms of manufacturing, product quality and economical aspects. Results point out the urgent need for standardized evaluation procedures for mini-tablets. Copyright © 2015. Published by Elsevier B.V.

Alendronate Sodium as Enteric Coated Solid Lipid Nanoparticles; Preparation, Optimization, and In Vivo Evaluation to Enhance Its Oral Bioavailability.

Directory of Open Access Journals (Sweden)

Khaled Mohamed Hosny

Full Text Available Treatment of osteoporosis with alendronate sodium has several challenges. The first challenge is the low bioavailability. The second main challenge is side effects, which include oesophageal ulceration. The aim of this research was to reformulate alendronate sodium as enteric coated solid lipid nanoparticles in order to enhance its bioavailability, and preventing the free alendronate sodium from coming into direct contact with the gastrointestinal mucosa, and thereby reducing the possibility of side effects. Enteric coated solid lipid nanoparticles were prepared according to the Box-Behnken design employing Design expert® software, and characterized for size, morphology, and entrapment efficiency. The optimized formula was coated with an Eudragit S100 and evaluated for drug release in acidic and basic media, stability studies and pharmacokinetic evaluations on rabbits. The results indicated that, using Derringer's desirability functional tool for optimization, the highest entrapment efficiency value of 74.3% and the smallest size value of 98 nm were predicted under optimum conditions with a desirability value of 0.917. The optimized nanoparticles released alendronate sodium only at an alkaline pH. The pharmacokinetic evaluation revealed that alendronate sodium bioavailability was enhanced by more than 7.4-fold in rabbits. In conclusion, enteric coated solid lipid nanoparticles is a promising formula for the delivery of alendronate sodium, eliminating its oesophageal side effects and enhancing its bioavailability.

Effect of magnesium stearate concentration on dissolution properties of ranitidine hydrochloride coated tablets.

Science.gov (United States)

Uzunović, Alija; Vranić, Edina

2007-08-01

Most pharmaceutical formulations also include a certain amount of lubricant to improve their flowability and prevent their adhesion to the surfaces of processing equipment. Magnesium stearate is an additive that is most frequently used as a lubricant. Magnesium stearate is capable of forming films on other tablet excipients during prolonged mixing, leading to a prolonged drug liberation time, a decrease in hardness, and an increase in disintegration time. It is hydrophobic, and there are many reports in the literature concerning its adverse effect on dissolution rates. The objective of this study was to evaluate the effects of two different concentrations of magnesium stearate on dissolution properties of ranitidine hydrochloride coated tablet formulations labeled to contain 150 mg. The uniformity content was also checked. During the drug formulation development, several samples were designed for choice of the formulation. For this study, two formulations containing 0,77 and 1,1% of magnesium stearate added in the manufacture of cores were chosen. Fraction of ranitidine hydrochloride released in dissolution medium was calculated from calibration curves. The data were analyzed using pharmacopeial test for similarity of dissolution profiles ( f2 equation), previously proposed by Moore and Flanner. Application of f2 equation showed differences in time-course of ranitidine hydrochloride dissolution properties. The obtained values indicate differences in drug release from analyzed ranitidine hydrochloride formulations and could cause differences in therapeutic response.

In Vitro Evaluation of Eslicarbazepine Delivery via Enteral Feeding Tubes.

Science.gov (United States)

Reindel, Kristin; Zhao, Fang; Hughes, Susan; Dave, Vivek S

2017-12-01

Purpose: The feasibility of preparing an eslicarbazepine acetate suspension using Aptiom tablets for administration via enteral feeding tubes was evaluated. Methods: Eslicarbazepine acetate suspension (40 mg/mL) was prepared using Aptiom tablets after optimizing the tablet crushing methods and the vehicle composition. A stability-indicating high-performance liquid chromatography (HPLC) method was developed to monitor the eslicarbazepine stability in the prepared suspension. Three enteric feeding tubes of various composition and dimensions were evaluated for the delivery of the suspensions. The suspension was evaluated for the physical and chemical stability for 48 hours. Results: The reproducibility and consistency of particle size reduction was found to be best with standard mortar/pestle. The viscosity analysis and physical stability studies showed that ORA-Plus:water (50:50 v/v) was optimal for suspending ability and flowability of suspension through the tubes. The developed HPLC method was found to be stability indicating and suitable for the assay of eslicarbazepine acetate in the prepared suspension. The eslicarbazepine concentrations in separately prepared suspensions were within acceptable range (±3%), indicating accuracy and reproducibility of the procedure. The eslicarbazepine concentrations in suspensions before and after delivery through the enteric feeding tubes were within acceptable range (±4%), indicating absence of any physical/chemical interactions of eslicarbazepine with the tubes and a successful delivery of eslicarbazepine dosage via enteric feeding tubes. The stability study results showed that eslicarbazepine concentration in the suspension remained unchanged when stored at room temperature for 48 hours. Conclusion: The study presents a convenient procedure for the preparation of a stable suspension of eslicarbazepine acetate (40 mg/mL) using Aptiom tablets, for administration via enteral feeding tubes.

Effect Of Formulating Additives On The Properties Of Ibuprofen Tablets

African Journals Online (AJOL)

A study of the comparative effects of different formulating additives and film coating on the properties of ibuprofen tablets was made. The tested properties were hardeness (H), friability (F), the disintegration time (D) and dissolution characteristics of ibuprofen tablets. The hardeness, friability, the hardeness friability ratio ...

Enteric coated HPMC capsules plugged with 5-FU loaded microsponges: a potential approach for treatment of colon cancer

Directory of Open Access Journals (Sweden)

Ankita Gupta

2015-09-01

Full Text Available The work was aimed at developing novel enteric coated HPMC capsules (ECHC plugged with 5 Florouracil (5-FU loaded Microsponges in combination with calcium pectinate beads. Modified quasi-emulsion solvent diffusion method was used to formulate microsponges based on 32 factorial design and the effects of independent variables (volume of organic solvent and Eudragit RS100 content on the dependent variables (Particle size, %EE & % CDR were determined. The optimized microsponges (F4 were characterized by SEM, PXRD, TGA and were plugged along with calcium pectinate beads in HPMC capsules and the HPMC capsules were further coated with enteric polymer Eudragit L 100 (Ed-L100 and/ or Eudrgit S 100 (Ed-S 100 in different proportions. In vitro release study of ECHC was performed in various release media sequentially SGF for 2 h, followed by SIF for the next 6 h and then in SCF (in the presence and absence of pectinase enzyme for further 16 h. Drug release was retarded on coating with EdS-100 in comparison to blend of EdS-100: EdL-100 coating. The percentage of 5-FU released at the end of 24 h from ECHC 3 was 97.83 ± 0.12% in the presence of pectinase whereas in control study it was 40.08 ± 0.02% drug. The optimized formulation was subjected to in vivo Roentgenographic studies in New Zealand white rabbits to analyze the in vivo behavior of the developed colon targeted capsules. Pharmacokinetic studies in New Zealand white rabbits were conducted to determine the extent of systemic exposure provided by the developed formulation in comparison to 5-FU aqueous solutions. Thus, enteric coated HPMC capsules plugged with 5-FU loaded microsponges and calcium pectinate beads proved to be promising dosage form for colon targeted drug delivery to treat colorectal cancer.

Influence of compression forces on tablets disintegration by AC Biosusceptometry.

Science.gov (United States)

Corá, Luciana A; Fonseca, Paulo R; Américo, Madileine F; Oliveira, Ricardo B; Baffa, Oswaldo; Miranda, José Ricardo A

2008-05-01

Analysis of physical phenomena that occurs during tablet disintegration has been studied by several experimental approaches; however none of them satisfactorily describe this process. The aim of this study was to investigate the influence of compression force on the tablets by associating the AC Biosusceptometry with consolidated methods in order to validate the biomagnetic technique as a tool for quality control in pharmaceutical processes. Tablets obtained at five compression levels were submitted to mechanical properties tests. For uncoated tablets, water uptake and disintegration force measurements were performed in order to compare with magnetic data. For coated tablets, magnetic measurements were carried out to establish a relationship between physical parameters of the disintegration process. According to the results, differences between the compression levels were found for water uptake, force development and magnetic area variation measurements. ACB method was able to estimate the disintegration properties as well as the kinetics of disintegration process for uncoated and coated tablets. This study provided a new approach for in vitro investigation and validated this biomagnetic technique as a tool for quality control for pharmaceutical industry. Moreover, using ACB will also be possible to test these parameters in humans allowing to establish an in vitro/in vivo correlation (IVIVC).

New insights on poly(vinyl acetate)-based coated floating tablets: characterisation of hydration and CO2 generation by benchtop MRI and its relation to drug release and floating strength.

Science.gov (United States)

Strübing, Sandra; Abboud, Tâmara; Contri, Renata Vidor; Metz, Hendrik; Mäder, Karsten

2008-06-01

The purpose of this study was to investigate the mechanism of floating and drug release behaviour of poly(vinyl acetate)-based floating tablets with membrane controlled drug delivery. Propranolol HCl containing tablets with Kollidon SR as an excipient for direct compression and different Kollicoat SR 30 D/Kollicoat IR coats varying from 10 to 20mg polymer/cm2 were investigated regarding drug release in 0.1N HCl. Furthermore, the onset of floating, the floating duration and the floating strength of the device were determined. In addition, benchtop MRI studies of selected samples were performed. Coated tablets with 10mg polymer/cm2 SR/IR, 8.5:1.5 coat exhibited the shortest lag times prior to drug release and floating onset, the fastest increase in and highest maximum values of floating strength. The drug release was delayed efficiently within a time interval of 24 h by showing linear drug release characteristics. Poly(vinyl acetate) proved to be an appropriate excipient to ensure safe and reliable drug release. Floating strength measurements offered the possibility to quantify the floating ability of the developed systems and thus to compare different formulations more efficiently. Benchtop MRI studies allowed a deeper insight into drug release and floating mechanisms noninvasively and continuously.

Design of tablets for the delayed and complete release of poorly water-soluble weak base drugs using SBE7M-β-CD as a solubilizing agent.

Science.gov (United States)

Rao, Venkatramana M; Zannou, Erika A; Stella, Valentino J

2011-04-01

The challenge of designing a delayed-release oral dosage form is significantly increased when the drug substance is poorly water soluble. This manuscript describes the design and characterization of a novel controlled-release film-coated tablet for the pH-triggered delayed and complete release of poorly water-soluble weak base drugs. Delivery of weak bases is specifically highlighted with the use of dipyridamole and prazosin as model compounds. Tailored delayed release is achieved with a combination of an insoluble but semipermeable polymer and an enteric polymer, such as cellulose acetate and hydroxypropyl cellulose phthalate, respectively, as coatings. The extent of the time lag prior to complete release depends on the film-coating composition and thickness. Complete release is achieved by the addition of a cyclodextrin, namely SBE7M-β-CD with or without a pH modifier added to the tablet core to ensure complete solubilization and release of the drug substance. The film-coating properties allow the complex formation/solubilization to occur in situ. Additionally, the drug release rate can be modulated on the basis of the cyclodextrin to drug molar ratio. This approach offers a platform technology for delayed release of potent but poorly soluble drugs and the release can be modulated by adjusting the film-coating composition and thickness and/or the cyclodextrin and pH modifier, if necessary. Copyright © 2010 Wiley-Liss, Inc.

Comparative effects of aspirin and enteric-coated aspirin on loss of chromium 51-labeled erythrocytes from the gastrointestinal tract

International Nuclear Information System (INIS)

Robbins, D.C.; Schwartz, R.S.; Kutny, K.; Vallejo, G.; Horton, E.S.; Cotter, J.M.

1984-01-01

Sodium chromate Cr 51 was used to label red blood cells of 19 healthy male volunteers, whose stools were collected for four days before and four days during oral administration of either uncoated (N . 9) or enteric-coated (N . 10) aspirin. Each subject received 2.925 gm/day of aspirin, in three equal doses separated by eight-hour intervals, for a total of seven days. During drug use, stools were collected on days 4 through 7. Fecal blood content, estimated by measuring radioactivity in the stools, was significantly higher (P less than 0.001) during use of either type of aspirin than at baseline, but losses measured during use of the coated aspirin (mean, 1.54 ml/day) were significantly lower (P less than 0.001) than those measured during use of the uncoated aspirin (mean, 4.33 ml/day). The two types of aspirin produced equivalent serum concentrations of salicylates. We conclude that enteric-coated aspirin reduces gastrointestinal blood loss

Effect of Magnesium Stearate Concentration on Dissolution Properties of Ranitidine Hydrochloride Coated Tablets

Directory of Open Access Journals (Sweden)

Alija Uzunović

2007-08-01

Full Text Available Most pharmaceutical formulations also include a certain amount of lubricant to improve their flowability and prevent their adhesion to the surfaces of processing equipment. Magnesium stearate is an additive that is most frequently used as a lubricant. Magnesium stearate is capable of forming films on other tablet excipients during prolonged mixing, leading to a prolonged drug liberation time, a decrease in hardness, and an increase in disintegration time. It is hydrophobic, and there are many reports in the literature concerning its adverse effect on dissolution rates.The objective of this study was to evaluate the effects of two different concentrations of magnesium stearate on dissolution properties of ranitidine hydrochloride coated tablet formulations labeled to contain 150 mg. The uniformity content was also checked.During the drug formulation development, several samples were designed for choice of the formulation. For this study, two formulations containing 0,77 and 1,1% of magnesium stearate added in the manufacture of cores were chosen. Fraction of ranitidine hydrochloride released in dissolution medium was calculated from calibration curves. The data were analyzed using pharmaco-peial test for similarity of dissolution profiles (f2 equation, previously proposed by Moore and Flanner.Application of f2 equation showed differences in time-course of ranitidine hydrochloride dissolution properties. The obtained values indicate differences in drug release from analyzed ranitidine hydrochloride formulations and could cause differences in therapeutic response.

PREPARATION AND CHARACTERIZATION OF CHITOSAN TABLETS OF ACECLOFENAC FOR COLON TARGETED DRUG DELIVERY

OpenAIRE

UMA DEVI,THIRUGANESH, SURESH

2013-01-01

The present study objective was to develop novel colon specific drug delivery systems for aceclofenac using chitosan as a microbially degradable polymeric carrier and to coat the optimized batches with a pH dependent polymeric coating solution containing Eudragit L 100 and S 100 (1:4). Tablets containing four proportions of chitosan were prepared. The tablets were evaluated for physicochemical properties, drug content, dissolution, water uptake & erosion characteristics, in vitro drug rel...

A non-destructive method for quality control of the pellet distribution within a MUPS tablet by terahertz pulsed imaging

DEFF Research Database (Denmark)

Novikova, Anna; Markl, Daniel; Axel Zeitler, J

2018-01-01

Terahertz pulsed imaging (TPI) was applied to analyse the inner structure of multiple unit pellet system (MUPS) tablets. MUPS tablets containing different amounts of theophylline pellets coated with Eudragit® NE 30 D and with microcrystalline cellulose (MCC) as cushioning agent were analysed....... The tablets were imaged by TPI and the results were compared to X-ray microtomography. The terahertz pulse beam propagates through the tablets and is back-reflected at the interface between the MCC matrix and the coated pellets within the tablet causing a peak in the terahertz waveform. Cross-section images...... of the tablets were extracted at different depths and parallel to the tablet faces from 3D terahertz data to visualize the surface-near structure of the MUPS tablets. The images of the surface-near structure of the MUPS tablets were compared to X-ray microtomography images at the same depths. The surface...

Ordinance on distribution of iodine tablets to the population

International Nuclear Information System (INIS)

1992-01-01

This Ordinance provides for the organization of supplies of iodine tablets to the population. The tablets will be held in case of occurrences that might endanger the population following an accident provoking the emission of radioactive iodine. The Federal Health Ministry is responsible for organizing the supply to the appropriate bodies for distribution to the population. The Ordinance entered into force on 1 August 1992. (NEA)

A Three-Pulse Release Tablet for Amoxicillin: Preparation, Pharmacokinetic Study and Physiologically Based Pharmacokinetic Modeling.

Science.gov (United States)

Li, Jin; Chai, Hongyu; Li, Yang; Chai, Xuyu; Zhao, Yan; Zhao, Yunfan; Tao, Tao; Xiang, Xiaoqiang

2016-01-01

Amoxicillin is a commonly used antibiotic which has a short half-life in human. The frequent administration of amoxicillin is often required to keep the plasma drug level in an effective range. The short dosing interval of amoxicillin could also cause some side effects and drug resistance, and impair its therapeutic efficacy and patients' compliance. Therefore, a three-pulse release tablet of amoxicillin is desired to generate sustained release in vivo, and thus to avoid the above mentioned disadvantages. The pulsatile release tablet consists of three pulsatile components: one immediate-release granule and two delayed release pellets, all containing amoxicillin. The preparation of a pulsatile release tablet of amoxicillin mainly includes wet granulation craft, extrusion/spheronization craft, pellet coating craft, mixing craft, tablet compression craft and film coating craft. Box-Behnken design, Scanning Electron Microscope and in vitro drug release test were used to help the optimization of formulations. A crossover pharmacokinetic study was performed to compare the pharmacokinetic profile of our in-house pulsatile tablet with that of commercial immediate release tablet. The pharmacokinetic profile of this pulse formulation was simulated by physiologically based pharmacokinetic (PBPK) model with the help of Simcyp®. Single factor experiments identify four important factors of the formulation, namely, coating weight of Eudragit L30 D-55 (X1), coating weight of AQOAT AS-HF (X2), the extrusion screen aperture (X3) and compression forces (X4). The interrelations of the four factors were uncovered by a Box-Behnken design to help to determine the optimal formulation. The immediate-release granule, two delayed release pellets, together with other excipients, namely, Avicel PH 102, colloidal silicon dioxide, polyplasdone and magnesium stearate were mixed, and compressed into tablets, which was subsequently coated with Opadry® film to produce pulsatile tablet of

Atomic layer deposition-A novel method for the ultrathin coating of minitablets.

Science.gov (United States)

Hautala, Jaana; Kääriäinen, Tommi; Hoppu, Pekka; Kemell, Marianna; Heinämäki, Jyrki; Cameron, David; George, Steven; Juppo, Anne Mari

2017-10-05

We introduce atomic layer deposition (ALD) as a novel method for the ultrathin coating (nanolayering) of minitablets. The effects of ALD coating on the tablet characteristics and taste masking were investigated and compared with the established coating method. Minitablets containing bitter tasting denatonium benzoate were coated by ALD using three different TiO 2 nanolayer thicknesses (number of deposition cycles). The established coating of minitablets was performed in a laboratory-scale fluidized-bed apparatus using four concentration levels of aqueous Eudragit ® E coating polymer. The coated minitablets were studied with respect to the surface morphology, taste masking capacity, in vitro disintegration and dissolution, mechanical properties, and uniformity of content. The ALD thin coating resulted in minimal increase in the dimensions and weight of minitablets in comparison to original tablet cores. Surprisingly, ALD coating with TiO 2 nanolayers decreased the mechanical strength, and accelerated the in vitro disintegration of minitablets. Unlike previous studies, the studied levels of TiO 2 nanolayers on tablets were also inadequate for effective taste masking. In summary, ALD permits a simple and rapid method for the ultrathin coating (nanolayering) of minitablets, and provides nanoscale-range TiO 2 coatings on porous minitablets. More research, however, is needed to clarify its potential in tablet taste masking applications. Copyright © 2017 Elsevier B.V. All rights reserved.

Challenges in detecting magnesium stearate distribution in tablets.

Science.gov (United States)

Lakio, Satu; Vajna, Balázs; Farkas, István; Salokangas, Henri; Marosi, György; Yliruusi, Jouko

2013-03-01

Magnesium stearate (MS) is the most commonly used lubricant in pharmaceutical industry. During blending, MS particles form a thin layer on the surfaces of the excipient and drug particles prohibiting the bonding from forming between the particles. This hydrophobic layer decreases the tensile strength of tablets and prevents water from penetrating into the tablet restraining the disintegration and dissolution of the tablets. Although overlubrication of the powder mass during MS blending is a well-known problem, the lubricant distribution in tablets has traditionally been challenging to measure. There is currently no adequate analytical method to investigate this phenomenon. In this study, the distribution of MS in microcrystalline cellulose (MCC) tablets was investigated using three different blending scales. The crushing strength of the tablets was used as a secondary response, as its decrease is known to result from the overlubrication. In addition, coating of the MCC particles by MS in intact tablets was detected using Raman microscopic mapping. MS blending was more efficient in larger scales. Raman imaging was successfully applied to characterize MS distribution in MCC tablets despite low concentration of MS. The Raman method can provide highly valuable visual information about the proceeding of the MS blending process. However, the measuring set-up has to be carefully planned to establish reliable and reproducible results.

Identification and Structural Characterization of Unidentified Impurity in Bisoprolol Film-Coated Tablets

Directory of Open Access Journals (Sweden)

Ivana Mitrevska

2017-01-01

Full Text Available The aim of this study is the identification, structural characterization, and qualification of a degradation impurity of bisoprolol labeled as Impurity RRT 0.95. This degradation product is considered as a principal thermal degradation impurity identified in bisoprolol film-coated tablets. The impurity has been observed in the stress thermal degradation study of the drug product. Using HPLC/DAD/ESI-MS method, a tentative structure was assigned and afterwards confirmed by detailed structural characterization using NMR spectroscopy. The structure of the target Impurity RRT 0.95 was elucidated as phosphomonoester of bisoprolol, having relative molecular mass of 406 (positive ionization mode. The structural characterization was followed by qualification of Impurity RRT 0.95 using several different in silico methodologies. From the results obtained, it can be concluded that no new structural alerts have been generated for Impurity RRT 0.95 relative to the parent compound bisoprolol. The current study presents an in-depth analysis of the full characterization and qualification of an unidentified impurity in a drug product with the purpose of properly defining the quality specification of the product.

Gastric transit and pharmacodynamics of a two-millimeter enteric-coated pancreatin microsphere preparation in patients with chronic pancreatitis

NARCIS (Netherlands)

Bruno, M. J.; Borm, J. J.; Hoek, F. J.; Delzenne, B.; Hofmann, A. F.; de Goeij, J. J.; van Royen, E. A.; van Leeuwen, D. J.; Tytgat, G. N.

1998-01-01

It has been suggested that enteric-coated pancreatin microsphere (ECPM) preparations with sphere sizes larger than 1.7 mm pass through the stomach at a slower rate than a meal and therefore may be less efficacious in restoring pancreatic enzyme activity than preparations with smaller sphere sizes.

Enteric-coated, pH-dependent peppermint oil capsules for the treatment of irritable bowel syndrome in children.

Science.gov (United States)

Kline, R M; Kline, J J; Di Palma J; Barbero, G J

2001-01-01

In a randomized, double-blind controlled trial, 42 children with irritable bowel syndrome (IBS) were given pH-dependent, enteric-coated peppermint oil capsules or placebo. After 2 weeks, 75% of those receiving peppermint oil had reduced severity of pain associated with IBS. Peppermint oil may be used as a therapeutic agent during the symptomatic phase of IBS.

Glucose-coated gold nanoparticles transfer across human brain endothelium and enter astrocytes in vitro.

Directory of Open Access Journals (Sweden)

Radka Gromnicova

Full Text Available The blood-brain barrier prevents the entry of many therapeutic agents into the brain. Various nanocarriers have been developed to help agents to cross this barrier, but they all have limitations, with regard to tissue-selectivity and their ability to cross the endothelium. This study investigated the potential for 4 nm coated gold nanoparticles to act as selective carriers across human brain endothelium and subsequently to enter astrocytes. The transfer rate of glucose-coated gold nanoparticles across primary human brain endothelium was at least three times faster than across non-brain endothelia. Movement of these nanoparticles occurred across the apical and basal plasma membranes via the cytosol with relatively little vesicular or paracellular migration; antibiotics that interfere with vesicular transport did not block migration. The transfer rate was also dependent on the surface coating of the nanoparticle and incubation temperature. Using a novel 3-dimensional co-culture system, which includes primary human astrocytes and a brain endothelial cell line hCMEC/D3, we demonstrated that the glucose-coated nanoparticles traverse the endothelium, move through the extracellular matrix and localize in astrocytes. The movement of the nanoparticles through the matrix was >10 µm/hour and they appeared in the nuclei of the astrocytes in considerable numbers. These nanoparticles have the correct properties for efficient and selective carriers of therapeutic agents across the blood-brain barrier.

Enabling the Tablet Product Development of 5-Fluorocytosine by Conjugate Acid Base Cocrystals.

Science.gov (United States)

Perumalla, Sathyanarayana R; Paul, Shubhajit; Sun, Changquan C

2016-06-01

5-Fluorocytosine (FC) is a high-dose antifungal drug that challenges the development of a tablet product due to poor solid-state stability and tabletability. Using 2 pharmaceutically acceptable conjugate acid base (CAB) cocrystals of FC with HCl and acesulfame, we have developed commercially viable high loading FC tablets. The tablets were prepared by direct compression using nano-coated microcrystalline cellulose Avicel PH105 as a tablet binder, which provided both excellent tabletability and good flowability. Commercial manufacturability of formulations based on both CAB cocrystals was verified on a compaction simulator. The results from an expedited friability study were used to set the compaction force, which yielded tablets with sufficient mechanical strength and rapid tablet disintegration. This work demonstrates the potential value of CAB cocrystals in drug product development. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Preparation and Evaluation of Enteric-Coated Chitosan Derivative-Based Microparticles Loaded with Salmon Calcitonin as an Oral Delivery System

Directory of Open Access Journals (Sweden)

Hiraku Onishi

2016-09-01

Full Text Available Background: The production of protein drugs has recently increased due to advances in biotechnology, but their clinical use is generally limited to parenteral administration due to low absorption in non-parenteral administration. Therefore, non-parenteral delivery systems allowing sufficient absorption draw much attention. Methods: Microparticles (MP were prepared using chitosan-4-thio-butylamidine conjugate (Ch-TBA, trimethyl-chitosan (TMC, and chitosan (Ch. Using salmon calcitonin (sCT as a model protein drug, Ch-TBA-, Ch-TBA/TMC (4/1-, and Ch-based MP were produced, and their Eudragit L100 (Eud-coated MP, named Ch-TBA-MP/Eud, Ch-TBA/TMC-MP/Eud, and Ch-MP/Eud, respectively, were prepared as oral delivery systems. These enteric-coated microparticles were examined in vitro and in vivo. Results: All microparticles before and after enteric coating had a submicron size (600–800 nm and micrometer size (1300–1500 nm, respectively. In vitro release patterns were similar among all microparticles; release occurred gradually, and the release rate was slower at pH 1.2 than at pH 6.8. In oral ingestion, Ch-TBA-MP/Eud suppressed plasma Ca levels most effectively among the microparticles tested. The relative effectiveness of Ch-TBA-MP/Eud to the intramuscular injection was 8.6%, while the sCT solution showed no effectiveness. Conclusion: The results suggest that Eud-coated Ch-TBA-based microparticles should have potential as an oral delivery system of protein drugs.

Poly(dimethylsiloxane) coatings for controlled drug release--polymer modifications.

Science.gov (United States)

Schulze Nahrup, J; Gao, Z M; Mark, J E; Sakr, A

2004-02-11

Modifications of endhydroxylated poly(dimethylsiloxane) (PDMS) formulations were studied for their ability to be applied onto tablet cores in a spray-coating process and to control drug release in zero-order fashion. Modifications of the crosslinker from the most commonly used tetraethylorthosilicate (TEOS) to the trifunctional 3-(2,3-epoxypropoxy)propyltrimethoxysilane (SIG) and a 1:1 mixture of the two were undertaken. Addition of methylpolysiloxane-copolymers were studied. Lactose, microcrystalline cellulose (MCC) and polyethylene glycol 8000 (PEG) were the channeling agents applied. The effects on dispersion properties were characterized by particle size distribution and viscosity. Mechanical properties of resulting free films were studied to determine applicability in a pan-coating process. Release of hydrochlorothiazide (marker drug) was studied from tablets coated in a lab-size conventional coating pan. All dispersions were found suitable for a spray-coating process. Preparation of free films showed that copolymer addition was not possible due to great decline in mechanical properties. Tablets coated with formulations containing PEG were most suitable to control drug release, at only 5% coating weight. Constant release rates could be achieved for formulations with up to 25% PEG; higher amounts resulted in a non-linear release pattern. Upon adding 50% PEG, a drug release of 63% over 24 h could be achieved.

Effect of Coating Solvent Ratio on the Drug Release Lag Time of ...

African Journals Online (AJOL)

Purpose: The aim of the study was to investigate the effect of hydro-alcohol coating solvent ratio on the surface texture and lag time of porous theophylline osmotic tablet. Methods: Porous theophylline osmotic pump tablets were formulated by direct compression and coated by spraying with varying ratios of water-alcohol ...

Studies on the mechanism of printing film-coated tablets containing titanium dioxide in the film by using UV laser irradiation.

Science.gov (United States)

Kato, Yoshiteru; Nakashima, Yasuhiko; Shino, Naoki; Sasaki, Koichi; Hosokawa, Akihiro; Ishihara, Hiroshi

2010-04-01

The purpose of this article is to study a detailed mechanism of printing when film-coated tablets were irradiated by UV laser at a wavelength of 355 nm. Hydroxypropylmethylcellulose (HPMC) film containing titanium dioxide (TiO(2)) and the film not containing TiO(2) and TiO(2) powder were lirradiated by the UV laser and estimated by the morphological observation by zoom stereo microscope, thermogravimetric analysis (TGA), total color difference (dE), X-ray powder diffraction (XRD), and dispersive Raman microscopy. In the case of the film containing TiO(2), the film showed a visible change in its color from white to gray by the UV laser irradiation. By zoom stereo microscope, it was found that the entire UV laser-irradiated area was not grayed uniformly, but many black particles, whose diameter was about 2 microm, were observed on the film. When TiO(2) powder was irradiated by the UV laser, a visible change in its color from white to gray was observed similar to the case of the film containing TiO(2). There were many black particles locally in the UV laser-treated TiO(2) powder by the morphological observation, and these black particles, agglomerates of the grayed oxygen-defected TiO(2), were associated with the visible change of the TiO(2). It was found that the film-coated tablets were printed utilizing the formation of the black particles by the agglomeration of the grayed oxygen-defected TiO(2) by the UV laser irradiation.

Development of the technology of tablets on the basis of ademetionine 1,4-butanedisulfonate

Directory of Open Access Journals (Sweden)

K. S. Burdak

2017-04-01

(resistance to crushing, abrasion, dissolution and disintegration research methods, it was proved that this technology allows to obtain tablets that are fully compliant with specifications for the tablets covered with an enteric coating.

Influence of disintegrants in different substrate physical form on dimensional recovery of multi-component tablet.

Science.gov (United States)

Sarkar, Srimanta; Ooi, Shing Ming; Liew, Celine Valeria; Tan, Bing Xun; Heng, Paul Wan Sia

2014-11-20

This study investigated the influence of different disintegrants, present in different substrate physical forms, on dimensional recovery of multi-component tablets prepared at different compression pressures. Formulations containing model drug, metformin, (10%, w/w), different disintegrants (10%, w/w), and lactose (80%, w/w) were compressed directly or after granulation using polyvinyl pyrrolidone (1%, w/w) as binder, into tablets (350 mg, 10mm diameter) at 150, 200, and 250 N/mm(2) compression pressures. Tablets were characterized for immediate dimensional recovery (IR) after ejection from the die, latent dimensional recovery (LR) over 24 h, tensile strength, and disintegration. The IR was predominantly contributed by crystalline components whereas LR was brought about by polymeric materials. With increased compression pressure, higher degree of plastic deformation of the polymeric disintegrants resulted in tablet with lower LR and higher tensile strength. Presence of polyvinyl pyrrolidone in the granules contributed considerably to plastic deformation, and the tablets produced had lower LR, higher tensile strength, and longer disintegration time. This study indicated that use of granules as the feed substrate physical form and a prudent selection of components may enable the coating of resultant tablets immediately after compression without the risk of coat damage due to LR. Copyright © 2014 Elsevier B.V. All rights reserved.

Spectrum of tablet computer use by medical students and residents at an academic medical center.

Science.gov (United States)

Robinson, Robert

2015-01-01

Introduction. The value of tablet computer use in medical education is an area of considerable interest, with preliminary investigations showing that the majority of medical trainees feel that tablet computers added value to the curriculum. This study investigated potential differences in tablet computer use between medical students and resident physicians. Materials & Methods. Data collection for this survey was accomplished with an anonymous online questionnaire shared with the medical students and residents at Southern Illinois University School of Medicine (SIU-SOM) in July and August of 2012. Results. There were 76 medical student responses (26% response rate) and 66 resident/fellow responses to this survey (21% response rate). Residents/fellows were more likely to use tablet computers several times daily than medical students (32% vs. 20%, p = 0.035). The most common reported uses were for accessing medical reference applications (46%), e-Books (45%), and board study (32%). Residents were more likely than students to use a tablet computer to access an electronic medical record (41% vs. 21%, p = 0.010), review radiology images (27% vs. 12%, p = 0.019), and enter patient care orders (26% vs. 3%, p e-Books, and to study for board exams. Residents were more likely to use tablet computers to complete clinical tasks. Conclusions. Tablet computer use among medical students and resident physicians was common in this survey. All learners used tablet computers for point of care references and board study. Resident physicians were more likely to use tablet computers to access the EMR, enter patient care orders, and review radiology studies. This difference is likely due to the differing educational and professional demands placed on resident physicians. Further study is needed better understand how tablet computers and other mobile devices may assist in medical education and patient care.

Limited sampling strategies drawn within 3 hours postdose poorly predict mycophenolic acid area-under-the-curve after enteric-coated mycophenolate sodium.

NARCIS (Netherlands)

Winter, B.C. de; Gelder, T. van; Mathôt, R.A.A.; Glander, P.; Tedesco-Silva, H.; Hilbrands, L.B.; Budde, K.; Hest, R.M. van

2009-01-01

Previous studies predicted that limited sampling strategies (LSS) for estimation of mycophenolic acid (MPA) area-under-the-curve (AUC(0-12)) after ingestion of enteric-coated mycophenolate sodium (EC-MPS) using a clinically feasible sampling scheme may have poor predictive performance. Failure of

Tabletted guar gum microspheres of piroxicam for targeted adjuvant therapy for colonic adenocarcinomas.

Science.gov (United States)

Vats, Anima; Pathak, Kamla

2012-11-01

In recent years, nonsteroidal anti-inflammatory drugs have been found to be cogent as an adjuvant therapeutic agent in mitigating colorectal cancer. Thus, this present investigation was aimed to formulate an oral, targeted tablet of piroxicam microspheres for sustained and targeted adjuvant therapy for colonic adenocarcinomas. Crosslinked guar gum microspheres of piroxicam were directly compressed into matrix tablet and coated with Eudragit S100. The optimized tablet that displayed 0% release in simulated gastric fluid, 15% in simulated intestinal fluid and 97.1% in simulated colonic fluid underwent roentgenographic study in rabbits to check its safe transit to the colon. x-ray images revealed intactness of the tablet until it reached the colon where the tablet matrix eroded. The designed, conceptual formulation emerged as potential carrier for targeted adjuvant therapy of piroxicam.

Spectrum of tablet computer use by medical students and residents at an academic medical center

Directory of Open Access Journals (Sweden)

Robert Robinson

2015-07-01

Full Text Available Introduction. The value of tablet computer use in medical education is an area of considerable interest, with preliminary investigations showing that the majority of medical trainees feel that tablet computers added value to the curriculum. This study investigated potential differences in tablet computer use between medical students and resident physicians.Materials & Methods. Data collection for this survey was accomplished with an anonymous online questionnaire shared with the medical students and residents at Southern Illinois University School of Medicine (SIU-SOM in July and August of 2012.Results. There were 76 medical student responses (26% response rate and 66 resident/fellow responses to this survey (21% response rate. Residents/fellows were more likely to use tablet computers several times daily than medical students (32% vs. 20%, p = 0.035. The most common reported uses were for accessing medical reference applications (46%, e-Books (45%, and board study (32%. Residents were more likely than students to use a tablet computer to access an electronic medical record (41% vs. 21%, p = 0.010, review radiology images (27% vs. 12%, p = 0.019, and enter patient care orders (26% vs. 3%, p < 0.001.Discussion. This study shows a high prevalence and frequency of tablet computer use among physicians in training at this academic medical center. Most residents and students use tablet computers to access medical references, e-Books, and to study for board exams. Residents were more likely to use tablet computers to complete clinical tasks.Conclusions. Tablet computer use among medical students and resident physicians was common in this survey. All learners used tablet computers for point of care references and board study. Resident physicians were more likely to use tablet computers to access the EMR, enter patient care orders, and review radiology studies. This difference is likely due to the differing educational and professional demands placed on

High-Throughput Synthetic Chemistry Enabled by Organic Solvent Disintegrating Tablet.

Science.gov (United States)

Li, Tingting; Xu, Lei; Xing, Yanjun; Xu, Bo

2017-01-17

Synthetic chemistry remains a time- and labor-intensive process of inherent hazardous nature. Our organic solvent disintegrating tablet (O-Tab) technology has shown potential to make industrial/synthetic chemistry more efficient. As is the case with pharmaceutical tablets, our reagent-containing O-Tabs are mechanically strong, but disintegrate rapidly when in contact with reaction media (organic solvents). For O-Tabs containing sensitive chemicals, they can be further coated to insulate them from air and moisture. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Formulation and Evaluation of pH-Responsive Mini-Tablets for Ileo ...

African Journals Online (AJOL)

Tropical Journal of Pharmaceutical Research July 2014; 13 (7): 1021-1029 ... Original Research Article. Formulation and ... in the early morning hours such as joint pain and functional .... along with placebo tablets were coated with the.

Modified geometry three-layered tablet as a platform for class II ...

African Journals Online (AJOL)

shape tablet composed of a core layer matrix made mainly of the enteric polymer hydroxypropyl methylcellulose acetate succinate and two barrier layers on either sides made of ethylcellulose. He showed that the system is capable of providing a.

In vitro pharmacokinetics of anti-psoriatic fumaric acid esters

NARCIS (Netherlands)

N.H.R. Litjens (Nicolle); E. van Strijen (Elizabeth); C. van Gulpen (Co); H. Mattie (Herman); J.T. van Dissel (Jaap); H.B. Thio (Bing); P.H. Nibbering (Peter)

2004-01-01

textabstractBackground: Psoriasis is a chronic inflammatory skin disease that can be successfully treated with a mixture of fumaric acid esters (FAE) formulated as enteric-coated tablets for oral use. These tablets consist of dimethylfumarate (DMF) and salts of monoethylfumarate (MEF) and its main

Evaluation of salmon calcitonin (sCT) enteric-coated capsule for enhanced absorption and GI tolerability in rats.

Science.gov (United States)

Wu, Lei; Zhang, Ge; Lu, Qin; Sun, Qian; Wang, Mulan; Li, Na; Gao, Zidong; Sun, Ya; Li, Tingting; Han, Deen; Yu, Xue; Wang, Lei; Sun, Wei; Zhao, Di; Wu, Yaning; Lu, Yang; Chen, Xijing

2010-03-01

Considering the chronic and repeated nature of salmon calcitonin (sCT) therapy, the oral route is a preferred route of administration. But, the oral bioavailability of sCT is very low due to enzymatic degradation and poor permeation across intestinal epithelial cells. It was the aim of this study to investigate the pharmacodynamic (PD), pharmacokinetic (PK), and mucosal injury characteristic of sCT oral delivery system. In this study, PD experiments were performed to find a suitable releasing region of sCT, an effect absorption enhancer, and an optimal mass ratio of sCT/enhancer. In addition, the PK experiments were designed to validate the absorption enhancement of this oral delivery system. Histopathological evaluations on the intestinal mucosa were carried out to assess any potential toxicity of the absorption enhancer. Through the PD research, we determined that oral sCT enteric-coated capsules containing sCT and citric acid (CA) with a ratio of 1:20 may be an adaptable delivery. PK study further proved that the oral absorption of sCT was enhanced from this delivery system. Finally, no damage on intestinal mucosa was observed when rats received the delivery system containing CA for up to 7 days. These results suggested that enteric-coated capsules with a certain amount of CA might give enhanced oral delivery of peptide drugs like sCT.

The practice and clinical implications of tablet splitting in international health

Science.gov (United States)

Elliott, Ivo; Mayxay, Mayfong; Yeuichaixong, Sengchanh; Lee, Sue J; Newton, Paul N

2014-01-01

Objective Tablet splitting is frequently performed to facilitate correct dosing, but the practice and implications in low-income settings have rarely been discussed. Methods We selected eight drugs, with narrow therapeutic indices or critical dosages, frequently divided in the Lao PDR (Laos). These were split, by common techniques used in Laos, by four nurses and four laypersons. The mean percentage deviation from the theoretical expected weight and weight loss of divided tablets/capsules were recorded. Results Five of eight study drugs failed, on splitting, to meet European Pharmacopoeia recommendations for tablet weight deviation from the expected weight of tablet/capsule halves with 10% deviating by more than 25%. There was a significant difference in splitting accuracy between nurses and laypersons (P = 0.027). Coated and unscored tablets were less accurately split than uncoated (P = 0.03 and 0.0019 for each half) and scored (0.0001 for both halves) tablets. Conclusion These findings have potential clinical implications on treatment outcome and the development of antimicrobial resistance. Investment by drug companies in a wider range of dosage units, particularly for narrow therapeutic index and critical dosage medicines, is strongly recommended. PMID:24702766

Bioequivalence study of a new sildenafil 100 mg orodispersible film compared to the conventional film-coated 100 mg tablet administered to healthy male volunteers

Science.gov (United States)

Radicioni, Milko; Castiglioni, Chiara; Giori, Andrea; Cupone, Irma; Frangione, Valeria; Rovati, Stefano

2017-01-01

A new orodispersible film formulation of the phosphodiesterase type 5 inhibitor, sildenafil, has been developed to examine the advantages of an orally disintegrating film formulation and provide an alternative to the current marketed products for the treatment of erectile dysfunction. The pharmacokinetics of the sildenafil 100 mg orodispersible film (IBSA) was compared to that of the conventional marketed 100 mg film-coated tablet (Viagra®) after single-dose administration to 53 healthy male volunteers (aged 18–51 years) in a randomized, open, two-way crossover bioequivalence study. Each subject received a single oral dose of 100 mg of sildenafil as test or reference formulation administered under fasting conditions at each of the two study periods according to a randomized crossover design. There was a washout interval of ≥7 days between the two administrations of the investigational medicinal products. Blood samples for pharmacokinetic analysis were collected up to 24 h post-dosing. The primary objective was to compare the rate (peak plasma concentration; Cmax) and extent (area under the curve [AUC] from administration to last observed concentration time; AUC0–t) of sildenafil absorption after single-dose administration of test and reference. Secondary endpoints were observed to describe the plasma pharmacokinetic profiles of sildenafil and its metabolite N-desmethyl-sildenafil relative bioavailability and safety profile after single-dose administration. The mean sildenafil and N-desmethyl-sildenafil plasma concentration–time profiles up to 24 h after single-dose administration of sildenafil 100 mg orodispersible film and film-coated tablet were nearly superimposable. The bioequivalence test was fully satisfied for sildenafil and N-desmethyl-sildenafil in terms of rate and extent of bioavailability. Adverse events occurred at similar rates for the two formulations and were of mild-to-moderate severity. The results suggest that the new orodispersible film

Development and validation of dissolution method for carvedilol compression-coated tablets

Directory of Open Access Journals (Sweden)

Ritesh Shah

2011-12-01

Full Text Available The present study describes the development and validation of a dissolution method for carvedilol compression-coated tablets. Dissolution test was performed using a TDT-06T dissolution apparatus. Based on the physiological conditions of the body, 0.1N hydrochloric acid was used as dissolution medium and release was monitored for 2 hours to verify the immediate release pattern of the drug in acidic pH, followed by pH 6.8 in citric-phosphate buffer for 22 hours, to simulate a sustained release pattern in the intestine. Influences of rotation speed and surfactant concentration in medium were evaluated. Samples were analysed by validated UV visible spectrophotometric method at 286 nm. 1% sodium lauryl sulphate (SLS was found to be optimum for improving carvedilol solubility in pH 6.8 citric-phosphate buffer. Analysis of variance showed no significant difference between the results obtained at 50 and 100 rpm. The discriminating dissolution method was successfully developed for carvedilol compression-coated tablets. The conditions that allowed dissolution determination were USP type I apparatus at 100 rpm, containing 1000 ml of 0.1N HCl for 2 hours, followed by pH 6.8 citric-phosphate buffer with 1% SLS for 22 hours at 37.0 ± 0.5 ºC. Samples were analysed by UV spectrophotometric method and validated as per ICH guidelines.O presente estudo descreve o desenvolvimento e a validação de método de dissolução para comprimidos revestidos de carvedilol. O teste de dissolução foi efetuado utilizando-se o aparelho para dissolução TDT-06T. Com base nas condições fisiológicas do organismo, utilizou-se ácido clorídrico 0,1 N como meio de dissolução e a liberação foi monitorada por 2 horas para se verificar o padrão de liberação imediata do fármaco em condições de pH baixo, seguidas por pH 6,8 em tampão cítrico-fosfato por 22 horas, para simular o padrão de liberação controlada no intestino. Avaliou-se a influência da velocidade de

Colon specific CODES based Piroxicam tablet for colon targeting: statistical optimization, in vivo roentgenography and stability assessment.

Science.gov (United States)

Singh, Amit Kumar; Pathak, Kamla

2015-03-01

This study was aimed to statistically optimize CODES™ based Piroxicam (PXM) tablet for colon targeting. A 3(2) full factorial design was used for preparation of core tablet that was subsequently coated to get CODES™ based tablet. The experimental design of core tablets comprised of two independent variables: amount of lactulose and PEG 6000, each at three different levels and the dependent variable was %CDR at 12 h. The core tablets were evaluated for pharmacopoeial and non-pharmacopoeial test and coated with optimized levels of Eudragit E100 followed by HPMC K15 and finally with Eudragit S100. The in vitro drug release study of F1-F9 was carried out by change over media method (0.1 N HCl buffer, pH 1.2, phosphate buffer, pH 7.4 and phosphate buffer, pH 6.8 with enzyme β-galactosidase 120 IU) to select optimized formulation F9 that was subjected to in vivo roentgenography. Roentgenography study corroborated the in vitro performance, thus providing the proof of concept. The experimental design was validated by extra check point formulation and Diffuse Reflectance Spectroscopy revealed absence of any interaction between drug and formulation excipients. The shelf life of F9 was deduced as 12 months. Conclusively, colon targeted CODES™ technology based PXM tablets were successfully optimized and its potential of colon targeting was validated by roentgenography.

Implantable repository adrenaline tablets for long-term studies in rats

International Nuclear Information System (INIS)

Korsatko, W.; Porta, S.; Sadjak, A.; Supanz, S.

1982-01-01

Implantable coated Eudragit matrix tablets containing adrenaline in various concentrations should overcome the problem of additional handling stress during long-term infusions. The efficiency of those tablets was tested in vitro, as well as in vivo using 14 C-adrenaline. Both in vitro and in vivo testing yielded satisfactorily output rates up to 20 h whereby the liver and serum content of 14 C-fragments served as an additional prove for the postulated mode of action. Good correlation has been found between the mentioned out-put rates and adrenaline serum levels (measured according to Da Prada). (author)

A randomized, phase I, double-blind, crossover study on pharmacokinetics of peppermint oil capsules in healthy volunteers : Enteric-coating versus colon-targeted-delivery

NARCIS (Netherlands)

Weerts, Z.Z.R.M.; Keszthelyi, D.; Frijlink, H.W.; Brouwers, J.R.B.J.; Vork, L.; Jonkers, D.M.A.E.; Masclee, A.A.M.

2016-01-01

Peppermint oil (PO) has been shown to reduce abdominal pain in patients with Irritable Bowel Syndrome (IBS). Menthol, the main constituent of PO, induces intestinal smooth muscle relaxation and desensitizes nociceptive nerve afferents. Enteric-coated (EC PO) capsules that release PO mainly in the

Investigation of the potential for direct compaction of a fine ibuprofen powder dry-coated with magnesium stearate.

Science.gov (United States)

Qu, Li; Zhou, Qi Tony; Gengenbach, Thomas; Denman, John A; Stewart, Peter J; Hapgood, Karen P; Gamlen, Michael; Morton, David A V

2015-05-01

Intensive dry powder coating (mechanofusion) with tablet lubricants has previously been shown to give substantial powder flow improvement. This study explores whether the mechanofusion of magnesium stearate (MgSt), on a fine drug powder can substantially improve flow, without preventing the powder from being directly compacted into tablets. A fine ibuprofen powder, which is both cohesive and possesses a low-melting point, was dry coated via mechanofusion with between 0.1% and 5% (w/w) MgSt. Traditional low-shear blending was also employed as a comparison. No significant difference in particle size or shape was measured following mechanofusion. For the low-shear blended powders, only marginal improvement in flowability was obtained. However, after mechanofusion, substantial improvements in the flow properties were demonstrated. Both XPS and ToF-SIMS demonstrated high degrees of a nano-scale coating coverage of MgSt on the particle surfaces from optimized mechanofusion. The study showed that robust tablets were produced from the selected mechanofused powders, at high-dose concentration and tablet tensile strength was further optimized via addition of a Polyvinylpyrrolidone (PVP) binder (10% w/w). The tablets with the mechanofused powder (with or without PVP) also exhibited significantly lower ejection stress than those made of the raw powder, demonstrating good lubrication. Surprisingly, the release rate of drug from the tablets made with the mechanofused powder was not retarded. This is the first study to demonstrate such a single-step dry coating of model drug with MgSt, with promising flow improvement, flow-aid and lubrication effects, tabletability and also non-inhibited dissolution rate.

A quality by design (QbD case study on enteric-coated pellets: Screening of critical variables and establishment of design space at laboratory scale

Directory of Open Access Journals (Sweden)

Shuling Kan

2014-10-01

Full Text Available The study aims to prepare naproxen enteric-coated pellets (NAP-ECPs by fluid-bed coating using QbD principle. Risk assessment was firstly performed by using failure mode and effect analysis (FMEA methodology. A Plackett–Burman design was then used for assessment of the most important variables affecting enteric-coated pellets characteristics. A Box–Behnken design was subsequently used for investigating the main, interactive, and quadratic effects of these variables on the response. By FMEA we discovered that eight factors should be considered to be high/important risk variables as compared with others. The responses of acid resistance and cumulative drug release were taken as critical quality attributes (CQAs. Pareto ranking analyses indicated that the coating weight gain (X7, triethyl citrate percentage (X1 and glycerol monostearate percentage (X2 were the most significant factors affecting the selected responses out of the eight high-risk variables. Optimization with response surface method (RSM further fully clarified the relationship between X7, X1, X2 and CQAs, and design space was established based on the constraints set on the responses. Due to the extreme coincidence of the predicted value generated by model with the observed value, the accuracy and robustness of the model were confirmed. It could be concluded that a promising NAP-ECPs was successfully designed using QbD approach in a laboratory scale.

Matrix tablets: the effect of hydroxypropyl methylcellulose/anhydrous dibasic calcium phosphate ratio on the release rate of a water-soluble drug through the gastrointestinal tract I. In vitro tests.

Science.gov (United States)

Mamani, Pseidy L; Ruiz-Caro, Roberto; Veiga, María D

2012-12-01

Different hydroxypropyl methylcellulose (HPMC)/anhydrous dibasic calcium phosphate (ADCP) matrix tablets have been developed aiming to evaluate the influence of both components ratio in the control release of a water-soluble drug (theophylline). In order to characterise the matrix tablets, swelling, buoyancy and dissolution studies have been carried out in different aqueous media (demineralised water, progressive pH medium, simulated gastric fluid, simulated intestinal fluid and simulated colonic fluid). The HPMC/ADCP ratio has turned out to be the determinant in the matrix behaviour: the HPMC characteristic swelling behaviour was modulated, in some cases, by the ADCP characteristic acidic dissolution. When the HPMC/ADCP ratio was ≥0.69, buoyancy, continuous swelling and low theophylline dissolution rate from the matrices (H1, H2 and H3) were observed in all dissolution media. Consequently, these formulations could be adequate as gastro-retentive drug delivery systems. Additionally, HPMC/ADCP ratio ≤0.11 (H5 and H6) induces a pH-dependent drug release which could be applied to design control drug release enteric formulations (with a suitable enteric coating). Finally, a HPMC/ADCP ratio between 0.11 and 0.69 (H4) yield a gastrointestinal controlled drug release, due to its time-dependent buoyancy (7 h) and a total drug delivery in 17 h in simulated colonic fluid.

[Tablets and tablet production - with special reference to Icelandic conditions].

Science.gov (United States)

Skaftason, Jóhannes F; Jóhannesson, Thorkell

2013-04-01

Modern tablet compression was instituted in England in 1844 by William Brockedon (1787-1854). The first tablets made according to Brockedon´s procedures contained watersoluble salts and were most likely compressed without expedients. In USA a watershed occurred around 1887 when starch (amylum maydis) was introduced to disperse tablets in aqueous milieu in order to corroborate bioavailability of drugs in the almentary canal. About the same time great advances in tablet production were introduced by the British firm Burroughs Wellcome and Co. In Denmark on the other hand tablet production remained on low scale until after 1920. As Icelandic pharmacies and drug firms modelled themselves mostly upon Danish firms tablet production was first instituted in Iceland around 1930. The first tablet machines in Iceland were hand-driven. More efficent machines came after 1945. Around 1960 three sizeable tablet producers were in Iceland; now there is only one. Numbers of individual tablet species (generic and proprietary) on the market rose from less than 10 in 1913 to 500 in 1965, with wide variations in numbers in between. Tablets have not wiped out other medicinal forms for peroral use but most new peroral drugs have been marketed in the form of tablets during the last decades.

Enteric-coated and highly standardized cranberry extract reduces antibiotic and nonsteroidal anti-inflammatory drug use for urinary tract infections during radiotherapy for prostate carcinoma

Directory of Open Access Journals (Sweden)

Bonetta A

2017-04-01

Full Text Available Alberto Bonetta,1 Giandomenico Roviello,2,3 Daniele Generali,3,4 Laura Zanotti,3 Maria Rosa Cappelletti,3 Chiara Pacifico,5 Francesco Di Pierro6 1Oncological Radiotherapy Operative Unit, ASST, Cremona, 2Department of Molecular and Translational Medicine, University of Brescia, Brescia, 3Molecular Therapy and Pharmacogenomics Unit, ASST, Cremona, 4Department of Medical, Surgery and Health Sciences, University of Trieste, Trieste, 5Department of Medical, Surgical and Neurological Sciences, University Hospital of Siena, Siena, 6Velleja Research Scientific Department, Milan, Italy Introduction: Worldwide, bacterial resistance to antibiotic therapy is a major concern for the medical community. Antibiotic resistance mainly affects Gram-negative bacteria that are an important cause of lower urinary tract infections (LUTIs. Pelvic irradiation for prostate cancer is a risk factor for LUTIs. Cranberry extract is reported to reduce the incidence of LUTIs. The prophylactic role of an enteric-coated, highly standardized cranberry extract (VO370® in reducing LUTI episodes, urinary discomfort, and nonsteroidal anti-inflammatory drug (NSAID and antibiotic use during radiotherapy for prostate carcinoma was evaluated. Methods: A total of 924 patients with prostate carcinoma treated by radiotherapy to the prostatic and pelvic areas were randomized to receive (n=489 or not (n=435 the enteric-coated, highly standardized cranberry extract for 6–7 weeks concurrently with irradiation. Outcomes were analyzed by using Mann–Whitney U test and Pearson’s X2 test. Primary endpoint was the number of patients with LUTI; secondary endpoints were incidence of recurrence, days of treatment with antibiotics and number of subjects treated with NSAIDs, and incidence of dysuria. Results: The treatment was very well tolerated, and there were no serious side effects. All enrolled patients completed the study. Urinary infections were detected in 53 of the 489 patients (10

OPTIMIZATION OF FUROSEMIDE LIQUISOLID TABLETS PREPARATION PROCESS LEADING TO THEIR MASS AND SIZE REDUCTION.

Science.gov (United States)

Kurek, Mateusz; Woyna-Orlewicz, Krzysztof; Khalid, Mohammad Hassan; Jachowicz, Renata

2016-09-01

The great number of drug substances currently used in solid oral dosage forms is characterized by poor water solubility. Therefore, various methods of dissolution rate enhancement are an important topic of research interest in modem drug technology. The purpose of this study was to enhance the furosemide dissolution rate from liquisolid tablets while maintaining an acceptable size and mass. Two types of dibasic calcium phosphate (Fujicalin®/Emcompress®) and microcrystalline cellulose (Vivapur® 102/Vivapur® 12) were used as carriers and magnesium aluminometasilicate (Neusilin® US2) was used as a coating material. The flowable liquid retention potential for those excipients was tested by measuring the angle of slide. To evaluate the impact of used excipients on tablet properties fourteen tablet formulations were prepared. It was found that LS2 tablets containing spherically granulated dibasic calcium phosphate and magnesium aluminometasilicate exhibit the best dissolution profile and mechanical properties while tablets composed only with Neusilin® US2 was characterized by the smallest size and mass with preserved good mechanical properties and furosemide dissolution.

Development of modified release 3D printed tablets (printlets) with pharmaceutical excipients using additive manufacturing.

Science.gov (United States)

Goyanes, Alvaro; Fina, Fabrizio; Martorana, Annalisa; Sedough, Daniel; Gaisford, Simon; Basit, Abdul W

2017-07-15

The aim of this study was to manufacture 3D printed tablets (printlets) from enteric polymers by single filament fused deposition modeling (FDM) 3D printing (3DP). Hot melt extrusion was used to generate paracetamol-loaded filaments from three different grades of the pharmaceutical excipient hypromellose acetate succinate (HPMCAS), grades LG, MG and HG. One-step 3DP was used to process these filaments into enteric printlets incorporating up to 50% drug loading with two different infill percentages (20 and 100%). X-ray Micro Computed Tomography (Micro-CT) analysis revealed that printlets with 20% infill had cavities in the core compared to 100% infill, and that the density of the 50% drug loading printlets was higher than the equivalent formulations loaded with 5% drug. In biorelevant bicarbonate dissolution media, drug release from the printlets was dependent on the polymer composition, drug loading and the internal structure of the formulations. All HPMCAS-based printlets showed delayed drug release properties, and in the intestinal conditions, drug release was faster from the printlets prepared with polymers with a lower pH-threshold: HPMCAS LG > HPMCAS MG > HPMCAS HG. These results confirm that FDM 3D printing makes it possible not only to manufacture delayed release printlets without the need for an outer enteric coating, but it is also feasible to adapt the release profile in response to the personal characteristics of the patient, realizing the full potential of additive manufacturing in the development of personalised dose medicines. Copyright © 2017 Elsevier B.V. All rights reserved.

Development of Colorectal-Targeted Dietary Supplement Tablets Containing Natural Purple Rice Bran Oil as a Colorectal Chemopreventive

Directory of Open Access Journals (Sweden)

Busaban Sirithunyalug

2018-04-01

Full Text Available Colorectal cancer occurs due to various factors. The important risks are dietary lifestyle and inflammatory bowel diseases, such as Crohn’s disease and ulcerative colitis. It has been found that the inhibitory enzyme cyclooxygenase-2 (COX-2 in the colorectal region can potentially reduce the risk of colorectal cancer. The present study investigated rice bran oil from natural purple rice bran, which exhibits antioxidant and anti-inflammatory activity. This study aimed to evaluate the bioactive compound content of natural purple rice bran oil (NPRBO derived from native Thai purple rice and the anti-inflammatory activity of NPRBO in colorectal cancer cells, and to develop a colorectal delivery platform in the form of film-coated tablets. NPRBO from the rice bran of five different Thai purple rice cultivars, namely Khao’ Gam Leum-Phua (KGLP, Khao’ Gam Boung (KGB, Khao’ Gam Thor (KGT, Khao’ Gam Pah E-Kaw (KGPEK, and Khao’ Niaw Dam (KND, were extracted using the supercritical carbon dioxide extraction technique. The amount of γ-oryzanol (ORY, tocotrienols, and tocopherols present in NPRBOs and the in vitro anti-inflammatory activity of NPRBO were investigated. The highest anti-inflammatory NPRBO was transformed into a dry and free-flowing powder by liquisolid techniques. Then, it was compressed into core tablets and coated with Eudragit®L100 and Eudragit® NE30D. The in vitro release study of the film-coated NPRBO tablets was performed in three-phase simulated gastrointestinal media. The cultivar KGLP was superior to the other samples in terms of the ORY, tocotrienol and tocopherol contents and anti-inflammatory activity. Aerosil® was the most suitable absorbent for transforming NPRBO into a free-flowing powder and was used to prepare the NPRBO core tablets. The in vitro KGLP-NPRBO film-coated tablet release profile showed that no ORY was released at gastric pH while 85% of ORY was released at pH 7.4 after 6 h; this would be expected to

Development of Colorectal-Targeted Dietary Supplement Tablets Containing Natural Purple Rice Bran Oil as a Colorectal Chemopreventive

Science.gov (United States)

Sirithunyalug, Busaban; Saenjum, Chalermpong; Charumanee, Suporn; Chaiyasut, Chaiyavat; Sirithunyalug, Jakkapan; Tipduangta, Pratchaya

2018-01-01

Colorectal cancer occurs due to various factors. The important risks are dietary lifestyle and inflammatory bowel diseases, such as Crohn’s disease and ulcerative colitis. It has been found that the inhibitory enzyme cyclooxygenase-2 (COX-2) in the colorectal region can potentially reduce the risk of colorectal cancer. The present study investigated rice bran oil from natural purple rice bran, which exhibits antioxidant and anti-inflammatory activity. This study aimed to evaluate the bioactive compound content of natural purple rice bran oil (NPRBO) derived from native Thai purple rice and the anti-inflammatory activity of NPRBO in colorectal cancer cells, and to develop a colorectal delivery platform in the form of film-coated tablets. NPRBO from the rice bran of five different Thai purple rice cultivars, namely Khao’ Gam Leum-Phua (KGLP), Khao’ Gam Boung (KGB), Khao’ Gam Thor (KGT), Khao’ Gam Pah E-Kaw (KGPEK), and Khao’ Niaw Dam (KND), were extracted using the supercritical carbon dioxide extraction technique. The amount of γ-oryzanol (ORY), tocotrienols, and tocopherols present in NPRBOs and the in vitro anti-inflammatory activity of NPRBO were investigated. The highest anti-inflammatory NPRBO was transformed into a dry and free-flowing powder by liquisolid techniques. Then, it was compressed into core tablets and coated with Eudragit®L100 and Eudragit® NE30D. The in vitro release study of the film-coated NPRBO tablets was performed in three-phase simulated gastrointestinal media. The cultivar KGLP was superior to the other samples in terms of the ORY, tocotrienol and tocopherol contents and anti-inflammatory activity. Aerosil® was the most suitable absorbent for transforming NPRBO into a free-flowing powder and was used to prepare the NPRBO core tablets. The in vitro KGLP-NPRBO film-coated tablet release profile showed that no ORY was released at gastric pH while 85% of ORY was released at pH 7.4 after 6 h; this would be expected to occur in

Estudo termoanalítico de comprimidos revestidos contendo captopril através de termogravimetria (TG e calorimetria exploratória diferencial (DSC Thermal analysis study of captopril coated tablets by thermogravimetry (TG and differential scanning calorimetry (DSC

Directory of Open Access Journals (Sweden)

Giovana Carolina Bazzo

2005-09-01

Full Text Available No presente trabalho foram desenvolvidos comprimidos de captopril revestidos com hidroxipropilmetilcelulose (HPMC, Opadry®, polivinilpirrolidona (PVP, Eudragit® E e goma laca. Foi realizado estudo termoanalítico do fármaco e das formulações através de termogravimetria (TG e calorimetria exploratória diferencial (DSC. Através da análise das curvas DSC verificou-se que não houve a ocorrência de interação entre o fármaco e os excipientes lactose, celulose microcristalina, croscarmelose sódica, Aerosil® e talco, utilizados na formulação do comprimido. Através desta técnica detectou-se a possibilidade de interação entre captopril e estearato de magnésio. De acordo com os resultados obtidos através de DSC não foram observadas alterações na cristalinidade do fármaco decorrentes dos processos de compressão e revestimento. A termogravimetria foi utilizada para o estudo da cinética de degradação do captopril e dos comprimidos. Os parâmetros cinéticos foram determinados através do método de Ozawa. Os resultados demonstraram que não houve alteração da estabilidade térmica do captopril na forma de comprimido. A formulação revestida com HPMC foi a que apresentou maior estabilidade térmica, quando comparada às demais formulações de revestimento.In the present study, captopril coated tablets with hydroxypropylmethylcellulose (HPMC, Opadry®, polyvinylpirrolidone (PVP, Eudragit® and shellac were produced. Differential scanning calorimetry (DSC and thermogravimetry (TG were used to evaluate the thermal properties of the drug and the formulations. On the basis of DSC results, captopril was found to be compatible with lactose, microcrystalline cellulose, sodium croscarmellose, Aerosil® and talc. Some possibility of interaction between drug-excipient was observed with magnesium stearate. However, additional techniques to confirm the results obtained are needed. There was no influence of mechanical treatment (tableting

TabletGaze: Unconstrained Appearance-based Gaze Estimation in Mobile Tablets

OpenAIRE

Huang, Qiong; Veeraraghavan, Ashok; Sabharwal, Ashutosh

2015-01-01

We study gaze estimation on tablets, our key design goal is uncalibrated gaze estimation using the front-facing camera during natural use of tablets, where the posture and method of holding the tablet is not constrained. We collected the first large unconstrained gaze dataset of tablet users, labeled Rice TabletGaze dataset. The dataset consists of 51 subjects, each with 4 different postures and 35 gaze locations. Subjects vary in race, gender and in their need for prescription glasses, all o...

Rapid Assessment of Tablet Film Coating Quality by Multispectral UV Imaging

DEFF Research Database (Denmark)

Klukkert, Marten; Wu, Jian X.; Rantanen, Jukka

2016-01-01

and coated with a polyvinyl alcohol-polyethylene glycol graft copolymer using a pan coater. It was demonstrated that the coating intactness can be assessed accurately and fast by UV imaging. The different types of coating defects could be differentiated and localized based on multivariate image analysis...

Iodine tablets - many benefits and few disadvantages

International Nuclear Information System (INIS)

Paile, W.

1996-01-01

The number of thyroid cancers among children has increased steeply around Chernobyl after the nuclear catastrophe. An iodine tablet taken at the right time would have protected the thyroid from the effects of radioiodine. Nuclear fallout may contain large amounts of radioactive iodine. If this enters the body, either through inhalation or ingestion, most of it ends up in the thyroid. As a result, the thyroid may be exposed to a considerable radiation dose. High doses endanger the functioning of the thyroid, and even smaller doses may cause benign or malignant tumours in the thyroid. Sensitivity of the thyroid to radiation depends largely on the person's age. The younger the child, the higher the risk. Adults probably have a low risk. It has not been shown that people over 40 years of age would have any risk of contracting radiation-induced thyroid cancer. Iodine tablets are particularly important for children. Iodine has fewer side effects than had been thought previously. At least for children, the risk of side effects caused by one dose of iodine is so small that it can be ignored when considering whether iodine should be given in a fallout situation. The risk increases with age. It must unconditionally be left for the authorities to decide who should be given iodine tablets and when. (orig.)

Tablet splitting and weight uniformity of half-tablets of 4 medications in pharmacy practice.

Science.gov (United States)

Tahaineh, Linda M; Gharaibeh, Shadi F

2012-08-01

Tablet splitting is a common practice for multiple reasons including cost savings; however, it does not necessarily result in weight-uniform half-tablets. To determine weight uniformity of half-tablets resulting from splitting 4 products available in the Jordanian market and investigate the effect of tablet characteristics on weight uniformity of half-tablets. Ten random tablets each of warfarin 5 mg, digoxin 0.25 mg, phenobarbital 30 mg, and prednisolone 5 mg were weighed and split by 6 PharmD students using a knife. The resulting half-tablets were weighed and evaluated for weight uniformity. Other relevant physical characteristics of the 4 products were measured. The average tablet hardness of the sampled tablets ranged from 40.3 N to 68.9 N. Digoxin, phenobarbital, and prednisolone half-tablets failed the weight uniformity test; however, warfarin half-tablets passed. Digoxin, warfarin, and phenobarbital tablets had a score line and warfarin tablets had the deepest score line of 0.81 mm. Splitting warfarin tablets produces weight-uniform half-tablets that may possibly be attributed to the hardness and the presence of a deep score line. Digoxin, phenobarbital, and prednisolone tablet splitting produces highly weight variable half-tablets. This can be of clinical significance in the case of the narrow therapeutic index medication digoxin.

Separation of selenium compounds by CE-ICP-MS in dynamically coated capillaries applied to selenized yeast samples

DEFF Research Database (Denmark)

Bendahl, Lars; Gammelgaard, Bente

2004-01-01

The selenium species in nutritional supplement tablets, based on selenized yeast, were separated by capillary zone electrophoresis using capillaries coated dynamically with poly(vinyl sulfonate) and detected by ICP-MS. Sample pre-treatment consisted of cold-water extraction by sonication and subs......The selenium species in nutritional supplement tablets, based on selenized yeast, were separated by capillary zone electrophoresis using capillaries coated dynamically with poly(vinyl sulfonate) and detected by ICP-MS. Sample pre-treatment consisted of cold-water extraction by sonication...

An oral modified-release nifedipine tablet (Adalat LA) and its appearance on double contrast barium enema

International Nuclear Information System (INIS)

Bleehen, Robert E.

2000-01-01

Adalat LA 30 mg and 60 mg tablets are widely prescribed oral modified release nifedipine preparations with a porous, non-digestible plastic tablet coating which is required in order to effect the osmotically driven slow release mechanism. These tablets may therefore be seen anywhere along the gastrointestinal tract and are passed apparently whole in the faeces. An example of the appearance within the rectum of Adalat LA 30 (Bayer) on double contrast barium enema is shown and the main features described. A review of the literature is given. Recognition of the appearances during the barium enema examination will prompt those performing the procedure to question the drug history where relevant and will reduce the incidence of false-positive reporting. Bleehen, R.E. (2000)

UV imaging of Multiple Unit Pellet System (MUPS) tablets: A case study of acetylsalicylic acid stability

DEFF Research Database (Denmark)

Novikova, Anna; Carstensen, Jens Michael; Rades, Thomas

2017-01-01

for estimation of the salicylic acid (SA) concentration as degradation product of ASA in the tablets were compared to the SA concentration measured by high performance liquid chromatography with a partial least squares regression resulting in an RMSEP of 4.86% and an R2 of 0.9812. The estimation of the SA......The applicability of multispectral ultraviolet (UV) imaging in combination with multivariate image analysis was investigated to monitor API degradation within multiple unit pellet system (MUPS) tablets during storage. For this purpose, acetylsalicylic acid (ASA) layered pellets were coated...

Preparation of sustained release capsules by electrostatic dry powder coating, using traditional dip coating as reference.

Science.gov (United States)

Yang, Yan; Shen, Lian; Yuan, Feng; Fu, Hui; Shan, Weiguang

2018-05-30

Lately, a great deal of attention is being paid to capsule coating, since the coat protects active pharmaceutical ingredients (APIs) from damage, as is in the case of tablet and pellet. However, moisture and heat sensitivity of gelatin shells make it challenging to coat capsules using the conventional aqueous coating techniques. In an effort to overcome this challenge, the present study aims to coat capsules using two different coating techniques: electrostatic dry powder coating (EDPC) and dip coating (DC). Both capsule coatings and free films were prepared by these two coating techniques, and the effects of coating formulations and processing conditions on the film quality were investigated. The corresponding drug in vitro release and mechanisms were characterized and compared. The results of dissolution tests demonstrated that the drug release behavior of both EDPC and DC coated capsules could be optimized to a sustained release of 24 h, following the Fick's diffusion law. The results of this study suggest that EDPC method is better than DC method for coating capsules, with respect to the higher production efficiency and better stability, indicating that this dry coating technology has promised in gelatin capsule coating applications. Copyright © 2018 Elsevier B.V. All rights reserved.

Performance of tablet disintegrants: impact of storage conditions and relative tablet density.

Science.gov (United States)

Quodbach, Julian; Kleinebudde, Peter

2015-01-01

Tablet disintegration can be influenced by several parameters, such as storage conditions, type and amount of disintegrant, and relative tablet density. Even though these parameters have been mentioned in the literature, the understanding of the disintegration process is limited. In this study, water uptake and force development of disintegrating tablets are analyzed, as they reveal underlying processes and interactions. Measurements were performed on dibasic calcium phosphate tablets containing seven different disintegrants stored at different relative humidities (5-97%), and on tablets containing disintegrants with different mechanisms of action (swelling and shape recovery), compressed to different relative densities. Disintegration times of tablets containing sodium starch glycolate are affected most by storage conditions, which is displayed in decreased water uptake and force development kinetics. Disintegration times of tablets with a swelling disintegrant are only marginally affected by relative tablet density, whereas the shape recovery disintegrant requires high relative densities for quick disintegration. The influence of relative tablet density on the kinetics of water uptake and force development greatly depends on the mechanism of action. Acquired data allows a detailed analysis of the influence of storage conditions and mechanisms of action on disintegration behavior.

A Pharmacokinetic Bioequivalence Study Comparing Pirfenidone Tablet and Capsule Dosage Forms in Healthy Adult Volunteers.

Science.gov (United States)

Pan, Lin; Belloni, Paula; Ding, Han Ting; Wang, Jianshuang; Rubino, Christopher M; Putnam, Wendy S

2017-09-01

Pirfenidone film-coated tablets were developed to offer an alternative to the marketed capsule formulation. This study assessed the bioequivalence of the tablet and capsule formulations under fed and fasted states. A Phase I, open-label, randomized, four-treatment-period, four-sequence, crossover pharmacokinetics study (NCT02525484) was conducted. Each subject received an 801-mg single dose of pirfenidone as three 267-mg capsules or one 801-mg tablet under fasted and fed conditions. Pirfenidone plasma C max , AUC 0-t and AUC 0-∞ were used to assess bioequivalence. Forty-four subjects were randomized to treatment. The 801-mg tablet in the fasted state met bioequivalence criteria [90% confidence intervals (CI) 80.00-125.00%] for the GLSM ratios of natural log-transformed C max , AUC 0-t and AUC 0-∞ . Under fed conditions, the 801-mg tablet met the bioequivalence criteria for AUC 0-t and AUC 0-∞ , but slightly exceeded the bioequivalence criteria for the C max (90% CI of 108.26-125.60%). The tablet C max was approximately 17% higher than that of the capsules. In the fed state, the tablet C max , and both AUC 0-t and AUC 0-∞ were reduced by 39% and 17%, respectively, relative to the fasted state. The tablet and capsules had acceptable tolerability profiles. The pirfenidone 801-mg tablet met bioequivalence criteria when compared with three 267-mg capsules in the fasted state. The tablet C max was slightly higher relative to capsules in the fed state, but this is not expected to have a clinically meaningful impact on the benefit-risk profile of pirfenidone. This work was supported by F. Hoffmann-La Roche Ltd.

Direct compression of chitosan: process and formulation factors to improve powder flow and tablet performance.

Science.gov (United States)

Buys, Gerhard M; du Plessis, Lissinda H; Marais, Andries F; Kotze, Awie F; Hamman, Josias H

2013-06-01

Chitosan is a polymer derived from chitin that is widely available at relatively low cost, but due to compression challenges it has limited application for the production of direct compression tablets. The aim of this study was to use certain process and formulation variables to improve manufacturing of tablets containing chitosan as bulking agent. Chitosan particle size and flow properties were determined, which included bulk density, tapped density, compressibility and moisture uptake. The effect of process variables (i.e. compression force, punch depth, percentage compaction in a novel double fill compression process) and formulation variables (i.e. type of glidant, citric acid, pectin, coating with Eudragit S®) on chitosan tablet performance (i.e. mass variation, tensile strength, dissolution) was investigated. Moisture content of the chitosan powder, particle size and the inclusion of glidants had a pronounced effect on its flow ability. Varying the percentage compaction during the first cycle of a double fill compression process produced chitosan tablets with more acceptable tensile strength and dissolution rate properties. The inclusion of citric acid and pectin into the formulation significantly decreased the dissolution rate of isoniazid from the tablets due to gel formation. Direct compression of chitosan powder into tablets can be significantly improved by the investigated process and formulation variables as well as applying a double fill compression process.

Tablet Use within Medicine

Science.gov (United States)

Hogue, Rebecca J.

2013-01-01

This paper discusses the scholarly literature related to tablet computer use in medicine. Forty-four research-based articles were examined for emerging categories and themes. The most studied uses for tablet computers include: patients using tablets to complete diagnostic survey instruments, medical professionals using tablet computers to view…

Bioequivalence study of a new sildenafil 100 mg orodispersible film compared to the conventional film-coated 100 mg tablet administered to healthy male volunteers

Directory of Open Access Journals (Sweden)

Radicioni M

2017-04-01

Full Text Available Milko Radicioni,1 Chiara Castiglioni,1 Andrea Giori,2 Irma Cupone,3 Valeria Frangione,4 Stefano Rovati4 1CROSS Research S.A., Phase I Unit, Arzo, Switzerland; 2IBSA Farmaceutici Italia, Lodi, Italy; 3Bouty S.p.A., Strada Padana Superiore, Cassina De’ Pecchi, Italy; 4IBSA Institut Biochimique S.A., Pambio-Noranco, Switzerland Abstract: A new orodispersible film formulation of the phosphodiesterase type 5 inhibitor, sildenafil, has been developed to examine the advantages of an orally disintegrating film formulation and provide an alternative to the current marketed products for the treatment of erectile dysfunction. The pharmacokinetics of the sildenafil 100 mg orodispersible film (IBSA was compared to that of the conventional marketed 100 mg film-coated tablet (Viagra® after single-dose administration to 53 healthy male volunteers (aged 18–51 years in a randomized, open, two-way crossover bioequivalence study. Each subject received a single oral dose of 100 mg of sildenafil as test or reference formulation administered under fasting conditions at each of the two study periods according to a randomized crossover design. There was a washout interval of ≥7 days between the two administrations of the investigational medicinal products. Blood samples for pharmacokinetic analysis were collected up to 24 h post-dosing. The primary objective was to compare the rate (peak plasma concentration; Cmax and extent (area under the curve [AUC] from administration to last observed concentration time; AUC0–t of sildenafil absorption after single-dose administration of test and reference. Secondary endpoints were observed to describe the plasma pharmacokinetic profiles of sildenafil and its metabolite N-desmethyl-sildenafil relative bioavailability and safety profile after single-dose administration. The mean sildenafil and N-desmethyl-sildenafil plasma concentration–time profiles up to 24 h after single-dose administration of sildenafil 100 mg

Quantifying Pharmaceutical Film Coating with Optical Coherence Tomography and Terahertz Pulsed Imaging: An Evaluation

Science.gov (United States)

Lin, Hungyen; Dong, Yue; Shen, Yaochun; Zeitler, J Axel

2015-01-01

Spectral domain optical coherence tomography (OCT) has recently attracted a lot of interest in the pharmaceutical industry as a fast and non-destructive modality for quantification of thin film coatings that cannot easily be resolved with other techniques. Because of the relative infancy of this technique, much of the research to date has focused on developing the in-line measurement technique for assessing film coating thickness. To better assess OCT for pharmaceutical coating quantification, this paper evaluates tablets with a range of film coating thickness measured using OCT and terahertz pulsed imaging (TPI) in an off-line setting. In order to facilitate automated coating quantification for film coating thickness in the range of 30–200 μm, an algorithm that uses wavelet denoising and a tailored peak finding method is proposed to analyse each of the acquired A-scan. Results obtained from running the algorithm reveal an increasing disparity between the TPI and OCT measured intra-tablet variability when film coating thickness exceeds 100 μm. The finding further confirms that OCT is a suitable modality for characterising pharmaceutical dosage forms with thin film coatings, whereas TPI is well suited for thick coatings. © 2015 The Authors. Journal of Pharmaceutical Sciences published by Wiley Periodicals, Inc. and the American Pharmacists Association J Pharm Sci 104:3377–3385, 2015 PMID:26284354

Food-dependent disintegration of immediate release fosamprenavir tablets: in vitro evaluation using magnetic resonance imaging and a dynamic gastrointestinal system.

Science.gov (United States)

Brouwers, Joachim; Anneveld, Bart; Goudappel, Gert-Jan; Duchateau, Guus; Annaert, Pieter; Augustijns, Patrick; Zeijdner, Evelijn

2011-02-01

In the present study, we demonstrated the value of two advanced tools, the TNO gastric and small Intestinal Model (TIM-1) and magnetic resonance imaging (MRI), for the in vitro evaluation of food-dependent disintegration of immediate release fosamprenavir tablets. Upon introduction of a tablet with the nutritional drink Scandishake Mix® in the stomach compartment of TIM-1, simulating the fed state, disintegration and fosamprenavir dissolution were significantly postponed compared to the fasted state (lag time 80 ± 23 min). This resulted in a lag in the appearance of bioaccessible fosamprenavir (tablet disintegration and subsequent amprenavir absorption in healthy volunteers. Therefore, TIM-1 can be used in tablet development to identify food-induced disintegration issues causing unexpected clinical behavior. From a mechanistic perspective, we applied MRI to illustrate impaired water ingress in fosamprenavir tablets immersed in the nutritional drink compared to simulated gastric fluid. This effect may be attributed to both competition between nutritional components and the tablet for the available water (indicated by reduced rotational and translational diffusion) as well as the possible formation of a food-dependent precipitation layer on the HPMC-coated tablet. Copyright © 2010 Elsevier B.V. All rights reserved.

Evaluation of coat uniformity and taste-masking efficiency of irregular-shaped drug particles coated in a modified tangential spray fluidized bed processor.

Science.gov (United States)

Xu, Min; Heng, Paul Wan Sia; Liew, Celine Valeria

2015-01-01

To explore the feasibility of coating irregular-shaped drug particles in a modified tangential spray fluidized bed processor (FS processor) and evaluate the coated particles for their coat uniformity and taste-masking efficiency. Paracetamol particles were coated to 20%, w/w weight gain using a taste-masking polymer insoluble in neutral and basic pH but soluble in acidic pH. In-process samples (5, 10 and 15%, w/w coat) and the resultant coated particles (20%, w/w coat) were collected to monitor the changes in their physicochemical attributes. After coating to 20%, w/w coat weight gain, the usable yield was 81% with minimal agglomeration (coat compared with the uncoated particles. A 15%, w/w coat was optimal for inhibiting drug release in salivary pH with subsequent fast dissolution in simulated gastric pH. The FS processor shows promise for direct coating of irregular-shaped drug particles with wide size distribution. The coated particles with 15% coat were sufficiently taste masked and could be useful for further application in orally disintegrating tablet platforms.

A new tablet brittleness index.

Science.gov (United States)

Gong, Xingchu; Sun, Changquan Calvin

2015-06-01

Brittleness is one of the important material properties that influences the success or failure of powder compaction. We have discovered that the reciprocal of diametrical elastic strain at fracture is the most suitable tablet brittleness indices (TBIs) for quantifying brittleness of pharmaceutical tablets. The new strain based TBI is supported by both theoretical considerations and a systematic statistical analysis of friability data. It is sufficiently sensitive to changes in both tablet compositions and compaction parameters. For all tested materials, it correctly shows that tablet brittleness increases with increasing tablet porosity for the same powder. In addition, TBI increases with increasing content of a brittle excipient, lactose monohydrate, in the mixtures with a plastic excipient, microcrystalline cellulose. A probability map for achieving less than 1% tablet friability at various combinations of tablet tensile strength and TBI was constructed. Data from marketed tablets validate this probability map and a TBI value of 150 is recommended as the upper limit for pharmaceutical tablets. This TBI can be calculated from the data routinely obtained during tablet diametrical breaking test, which is commonly performed for assessing tablet mechanical strength. Therefore, it is ready for adoption for quantifying tablet brittleness to guide tablet formulation development since it does not require additional experimental work. Copyright © 2015 Elsevier B.V. All rights reserved.

Dose Uniformity of Scored and Unscored Tablets: Application of the FDA Tablet Scoring Guidance for Industry.

Science.gov (United States)

Ciavarella, Anthony B; Khan, Mansoor A; Gupta, Abhay; Faustino, Patrick J

This U.S. Food and Drug Administration (FDA) laboratory study examines the impact of tablet splitting, the effect of tablet splitters, and the presence of a tablet score on the dose uniformity of two model drugs. Whole tablets were purchased from five manufacturers for amlodipine and six for gabapentin. Two splitters were used for each drug product, and the gabapentin tablets were also split by hand. Whole and split amlodipine tablets were tested for content uniformity following the general chapter of the United States Pharmacopeia (USP) Uniformity of Dosage Units , which is a requirement of the new FDA Guidance for Industry on tablet scoring. The USP weight variation method was used for gabapentin split tablets based on the recommendation of the guidance. All whole tablets met the USP acceptance criteria for the Uniformity of Dosage Units. Variation in whole tablet content ranged from 0.5 to 2.1 standard deviation (SD) of the percent label claim. Splitting the unscored amlodipine tablets resulted in a significant increase in dose variability of 6.5-25.4 SD when compared to whole tablets. Split tablets from all amlodipine drug products did not meet the USP acceptance criteria for content uniformity. Variation in the weight for gabapentin split tablets was greater than the whole tablets, ranging from 1.3 to 9.3 SD. All fully scored gabapentin products met the USP acceptance criteria for weight variation. Size, shape, and the presence or absence of a tablet score can affect the content uniformity and weight variation of amlodipine and gabapentin tablets. Tablet splitting produced higher variability. Differences in dose variability and fragmentation were observed between tablet splitters and hand splitting. These results are consistent with the FDA's concerns that tablet splitting can have an effect on the amount of drug present in a split tablet and available for absorption. Tablet splitting has become a very common practice in the United States and throughout the

Study of drug release and tablet characteristics of silicone adhesive matrix tablets.

Science.gov (United States)

Tolia, Gaurav; Li, S Kevin

2012-11-01

Matrix tablets of a model drug acetaminophen (APAP) were prepared using a highly compressible low glass transition temperature (T(g)) polymer silicone pressure sensitive adhesive (PSA) at various binary mixtures of silicone PSA/APAP ratios. Matrix tablets of a rigid high T(g) matrix forming polymer ethyl cellulose (EC) were the reference for comparison. Drug release study was carried out using USP Apparatus 1 (basket), and the relationship between the release kinetic parameters of APAP and polymer/APAP ratio was determined to estimate the excipient percolation threshold. The critical points attributed to both silicone PSA and EC tablet percolation thresholds were found to be between 2.5% and 5% w/w. For silicone PSA tablets, satisfactory mechanical properties were obtained above the polymer percolation threshold; no cracking or chipping of the tablet was observed above this threshold. Rigid EC APAP tablets showed low tensile strength and high friability. These results suggest that silicone PSA could eliminate issues related to drug compressibility in the formulation of directly compressed oral controlled release tablets of poorly compressible drug powder such as APAP. No routinely used excipients such as binders, granulating agents, glidants, or lubricants were required for making an acceptable tablet matrix of APAP using silicone PSA. Copyright © 2012 Elsevier B.V. All rights reserved.

Scintigraphic study of gastrointestinal transit and disintegration sites of mesalazine tablets labelled with technetium 99m

Energy Technology Data Exchange (ETDEWEB)

Sciarretta, G.; Furno, A.; Mazzoni, M.; Ferrieri, A.; Malaguti, P. (Ospedale Maggiore, Bologna (Italy))

1993-09-01

Tablets of mesalazine covered with a pH-dependent coating, labelled by an original technique with technetium-99m, were administered to 12 patients, 9 with Crohn's disease, 3 of which recurrent, 1 with ulcerative colitis, and 2 with irritable bowel syndrome, with the aim of verifying in vivo the intestinal site of disintegration and how the contents spread throughout the intestine. In all cases the tablet was broken down in the distal ileum at extremely variable intervals, from 5 to 27 h, and the contents spread into the nearby loops and into the colon. The notable differences in the residence time of the whole tablet in the ileum can be explained by differences in adhesion the inflamed mucosa and by a lower pH in the part of the ileum affected by the disease. 7 refs., 2 figs., 1 tab.

Scintigraphic study of gastrointestinal transit and disintegration sites of mesalazine tablets labelled with technetium 99m

International Nuclear Information System (INIS)

Sciarretta, G.; Furno, A.; Mazzoni, M.; Ferrieri, A.; Malaguti, P.

1993-01-01

Tablets of mesalazine covered with a pH-dependent coating, labelled by an original technique with technetium-99m, were administered to 12 patients, 9 with Crohn's disease, 3 of which recurrent, 1 with ulcerative colitis, and 2 with irritable bowel syndrome, with the aim of verifying in vivo the intestinal site of disintegration and how the contents spread throughout the intestine. In all cases the tablet was broken down in the distal ileum at extremely variable intervals, from 5 to 27 h, and the contents spread into the nearby loops and into the colon. The notable differences in the residence time of the whole tablet in the ileum can be explained by differences in adhesion the inflamed mucosa and by a lower pH in the part of the ileum affected by the disease. 7 refs., 2 figs., 1 tab

Pharmacokinetic bioequivalence studies of a fixed-dose combination of tamsulosin and dutasteride in healthy volunteers.

Science.gov (United States)

Fossler, Michael J; Collins, David A; Thompson, Meg M; Nino, Antonio; Bianco, Joseph J; Chetty, Dushen

2014-05-01

The combination of dutasteride and tamsulosin may be more effective for the treatment of symptomatic benign prostatic hyperplasia than either treatment alone. We report the results of three pharmacokinetics and tolerability studies, which used a dutasteride/tamsulosin HCl (0.5 mg/0.2 mg) fixed-dose combination (FDC) capsules containing a small dutasteride soft gelatin capsule (smaller than commercial Avodart™) and modified-release tamsulosin pellets that have different amounts of enteric coating. These studies compared the test products to commercial Avodart™ (dutasteride 0.5 mg) and two different commercial tamsulosin HCl 0.2 mg products, Harnal™ Capsules or Harnal-D™ Tablets, which are reportedly bioequivalent to each other. All three studies were randomized single-dose studies in healthy male adults. Study 1 [N = 86 (NCT01254071)] was a two-period crossover study of a dutasteride/tamsulosin HCl FDC versus coadministered Avodart™ and Harnal-D™ Tablets. The pharmacokinetics of both dutasteride and tamsulosin were studied. Study 2 [N = 27 (NCT01471678)] was a four-period crossover study of dutasteride/tamsulosin HCl FDC formulations versus Avodart™ and Harnal™ Capsules or Harnal-D™ Tablets. Only the pharmacokinetics of tamsulosin were studied. Study 3 [N = 40 (NCT01495026)] was a two-period study of dutasteride/tamsulosin HCl FDC formulations versus coadministered Avodart™ and Harnal-D™ Tablets. In this study, only the pharmacokinetics of tamsulosin were studied. Study 2 assessed fed-state pharmacokinetics. Studies 1 and 3 assessed fed- and fasted-state pharmacokinetics. All dutasteride/tamsulosin HCl FDC formulations and coadministered treatments were well-tolerated. In Study 1, the FDC dutasteride was bioequivalent to Avodart™ coadministered with tamsulosin under fed and fasted conditions. In Study 1, the FDC tamsulosin had a slower release than commercial Harnal-D™ Tablets coadministered with dutasteride (fed and fasted

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 149 ... Awot Gebreegziabher, Asfaw Debella. Vol 32, No 1 (2016), Comparative Evaluation and Optimization of Film Coating Formulation Variables and Delayed Release Properties of Three Enteric Polymers on Diclofenac Sodium Core Tablets, Abstract. Mosis Adugna, Anteneh Belete, Tsige Gebre-Mariam.

The Barrier Properties of PET Coated DLC Film Deposited by Microwave Surface-Wave PECVD

Science.gov (United States)

Yin, Lianhua; Chen, Qiang

2017-12-01

In this paper we report the investigation of diamond-like carbon (DLC) deposited by microwave surface-wave plasma enhanced chemical vapor deposition (PECVD) on the polyethylene terephthalate (PET) web for the purpose of the barrier property improvement. In order to characterize the properties of DLC coatings, we used several substrates, silicon wafer, glass, and PET web and KBr tablet. The deposition rate was obtained by surface profiler based on the DLC deposited on glass substrates; Fourier transform infrared spectroscope (FTIR) was carried out on KBr tablets to investigate chemical composition and bonding structure; the morphology of the DLC coating was analyzed by atomic force microscope (AFM) on Si substrates. For the barrier properties of PET webs, we measured the oxygen transmission rate (OTR) and water vapor transmission rate (WVTR) after coated with DLC films. We addressed the film barrier property related to process parameters, such as microwave power and pulse parameter in this work. The results show that the DLC coatings can greatly improve the barrier properties of PET webs.

Use of multiple pinhole external scintigraphy to monitor tablet disintegration in vivo

International Nuclear Information System (INIS)

Theodorakis, M.C.; Devous, M.D.; Simpson, D.R.

1982-01-01

External scintigraphy is useful for observing the disintegration of capsules and tablets in the gastro-intestinal tract of man and animals. The sites of disintegration, completeness of disintegration, effectiveness of coatings and rate of transition through the intestinal tract can be investigated by this technique. Gamma cameras are coupled to a digital data processor, video image processor and image magnifier, for increased resolution. Disintegration times in vitro and in vivo are compared. (U.K.)

Pharmaceutical counselling about different types of tablet-splitting methods based on the results of weighing tests and mechanical development of splitting devices.

Science.gov (United States)

Somogyi, O; Meskó, A; Csorba, L; Szabó, P; Zelkó, R

2017-08-30

The division of tablets and adequate methods of splitting them are a complex problem in all sectors of health care. Although tablet-splitting is often required, this procedure can be difficult for patients. Four tablets were investigated with different external features (shape, score-line, film-coat and size). The influencing effect of these features and the splitting methods was investigated according to the precision and "weight loss" of splitting techniques. All four types of tablets were halved by four methods: by hand, with a kitchen knife, with an original manufactured splitting device and with a modified tablet splitter based on a self-developed mechanical model. The mechanical parameters (harness and friability) of the products were measured during the study. The "weight loss" and precision of splitting methods were determined and compared by statistical analysis. On the basis of the results, the external features (geometry), the mechanical parameters of tablets and the mechanical structure of splitting devices can influence the "weight loss" and precision of tablet-splitting. Accordingly, a new decision-making scheme was developed for the selection of splitting methods. In addition, the skills of patients and the specialties of therapy should be considered so that pharmaceutical counselling can be more effective regarding tablet-splitting. Copyright © 2017 Elsevier B.V. All rights reserved.

Esophageal transit and in vivo disintegration of branded risedronate sodium tablets and two generic formulations of alendronic acid tablets: a single-center, single-blind, six-period crossover study in healthy female subjects.

Science.gov (United States)

Perkins, Alan C; Blackshaw, P Elaine; Hay, Peter D; Lawes, Simon C; Atherton, Clare T; Dansereau, Richard J; Wagner, Leigh K; Schnell, Dan J; Spiller, Robin C

2008-05-01

Delayed esophageal transit or disintegration of oral bisphosphonate tablets before they enter the stomach may be of concern with respect to iatrogenic complications among patients receiving longterm treatment. Different formulations of generic bisphosphonate tablets meeting regulatory requirements may have substantial differences in pharmaceutical attributes from the branded product that may result in different characteristics during esophageal transit. The primary objective of this study was to evaluate and compare esophageal transit times and in vivo disintegration of 3 bisphosphonate formulations, one branded and the others generic, that are commercially available in Canada and the United Kingdom. This was a single-center, randomized, singleblind, 6-period crossover study in healthy postmenopausal women aged >50 years. Each subject received a single oral dose of a branded risedronate sodium 35-mg tablet and 2 generic formulations of alendronic acid 70-mg tablets (Novopharm Limited, Toronto, Canada, and Teva UK Limited, Morley, United Kingdom) in both the erect and semisupine (45 degrees ) positions. Although the products are labeled to be taken in the erect position, the semisupine position was included to simulate dosing in bedridden patients. Subjects took tablets with 30 mL of water in the morning after an overnight fast. The tablets were radiolabeled with technetium-99m ion-exchange resins to enable visualization and measurement of esophageal transit time and disintegration using a gamma camera. Dynamic scintigraphic images were obtained for a total of 10 minutes: 2 images per second for the first 30 seconds and 1 image every 15 seconds for 9.5 minutes. This was a mechanistic study and tolerability was not assessed. The study was conducted in 20 healthy white female subjects with a mean age of 62 years (range, 51-77 years). The effect of body position was statistically significant (P = 0.043), with the estimated hazard ratio (HR) of 0.74 indicating longer

Enteric Micromotor Can Selectively Position and Spontaneously Propel in the Gastrointestinal Tract.

Science.gov (United States)

Li, Jinxing; Thamphiwatana, Soracha; Liu, Wenjuan; Esteban-Fernández de Ávila, Berta; Angsantikul, Pavimol; Sandraz, Elodie; Wang, Jianxing; Xu, Tailin; Soto, Fernando; Ramez, Valentin; Wang, Xiaolei; Gao, Weiwei; Zhang, Liangfang; Wang, Joseph

2016-09-22

The gastrointestinal (GI) tract, which hosts hundreds of bacteria species, becomes the most exciting organ for the emerging microbiome research. Some of these GI microbes are hostile and cause a variety of diseases. These bacteria colonize in different segments of the GI tract dependent on the local physicochemical and biological factors. Therefore, selectively locating therapeutic or imaging agents to specific GI segments is of significant importance for studying gut microbiome and treating various GI-related diseases. Herein, we demonstrate an enteric micromotor system capable of precise positioning and controllable retention in desired segments of the GI tract. These motors, consisting of magnesium-based tubular micromotors coated with an enteric polymer layer, act as a robust nanobiotechnology tool for site-specific GI delivery. The micromotors can deliver payload to a particular location via dissolution of their enteric coating to activate their propulsion at the target site toward localized tissue penetration and retention.

Defined drug release from 3D-printed composite tablets consisting of drug-loaded polyvinylalcohol and a water-soluble or water-insoluble polymer filler.

Science.gov (United States)

Tagami, Tatsuaki; Nagata, Noriko; Hayashi, Naomi; Ogawa, Emi; Fukushige, Kaori; Sakai, Norihito; Ozeki, Tetsuya

2018-05-30

3D-printed tablets are a promising new approach for personalized medicine. In this study, we fabricated composite tablets consisting of two components, a drug and a filler, by using a fused deposition modeling-type 3D printer. Polyvinylalcohol (PVA) polymer containing calcein (a model drug) was used as the drug component and PVA or polylactic acid (PLA) polymer without drug was used as the water-soluble or water-insoluble filler, respectively. Various kinds of drug-PVA/PVA and drug-PVA/PLA composite tablets were designed, and the 3D-printed tablets exhibited good formability. The surface area of the exposed drug component is highly correlated with the initial drug release rate. Composite tablets with an exposed top and a bottom covered with a PLA layer were fabricated. These tablets showed zero-order drug release by maintaining the surface area of the exposed drug component during drug dissolution. In contrast, the drug release profile varied for tablets whose exposed surface area changed. Composite tablets with different drug release lag times were prepared by changing the thickness of the PVA filler coating the drug component. These results which used PVA and PLA filler will provide useful information for preparing the tablets with multi-components and tailor-made tablets with defined drug release profiles using 3D printers. Copyright © 2018 Elsevier B.V. All rights reserved.

Compressibility of tableting materials and properties of tablets with glyceryl behenate

Directory of Open Access Journals (Sweden)

Mužíková Jitka

2015-03-01

Full Text Available The paper studies the compressibility of directly compressible tableting materials with dry binders, spray-dried lactose and microcrystalline cellulose, and glyceryl dibehenate at various concentrations. Compressibility was evaluated by means of the energy profile of compression and tensile strength of tablets. Release rate of the active ingredient, salicylic acid, from the tablets was also examined. In the case of microcrystalline cellulose, a higher concentration of glyceryl dibehenate increased the strength of tablets, while this did not occur in the case of spray-dried lactose. Increasing concentration of glyceryl dibehenate prolonged the release of salicylic acid; however, no statistically significant difference was found compared to the type of the dry binder used

Six sigma: process of understanding the control and capability of ranitidine hydrochloride tablet.

Science.gov (United States)

Chabukswar, Ar; Jagdale, Sc; Kuchekar, Bs; Joshi, Vd; Deshmukh, Gr; Kothawade, Hs; Kuckekar, Ab; Lokhande, Pd

2011-01-01

The process of understanding the control and capability (PUCC) is an iterative closed loop process for continuous improvement. It covers the DMAIC toolkit in its three phases. PUCC is an iterative approach that rotates between the three pillars of the process of understanding, process control, and process capability, with each iteration resulting in a more capable and robust process. It is rightly said that being at the top is a marathon and not a sprint. The objective of the six sigma study of Ranitidine hydrochloride tablets is to achieve perfection in tablet manufacturing by reviewing the present robust manufacturing process, to find out ways to improve and modify the process, which will yield tablets that are defect-free and will give more customer satisfaction. The application of six sigma led to an improved process capability, due to the improved sigma level of the process from 1.5 to 4, a higher yield, due to reduced variation and reduction of thick tablets, reduction in packing line stoppages, reduction in re-work by 50%, a more standardized process, with smooth flow and change in coating suspension reconstitution level (8%w/w), a huge cost reduction of approximately Rs.90 to 95 lakhs per annum, an improved overall efficiency by 30% approximately, and improved overall quality of the product.

Prediction of effects of punch shapes on tableting failure by using a multi-functional single-punch tablet press

Directory of Open Access Journals (Sweden)

Takashi Osamura

2017-09-01

Full Text Available We previously determined “Tableting properties” by using a multi-functional single-punch tablet press (GTP-1. We proposed plotting “Compactability” on the x-axis against “Manufacturability” on the y-axis to allow visual evaluation of “Tableting properties”. Various types of tableting failure occur in commercial drug production and are influenced by the amount of lubricant used and the shape of the punch. We used the GTP-1 to measure “Tableting properties” with different amounts of lubricant and compared the results with those of tableting on a commercial rotary tableting machine. Tablets compressed with a small amount of lubricant showed bad “Manufacturability”, leading to sticking of powder on punches. We also tested various punch shapes. The GTP-1 correctly predicted the actual tableting results for all punch shapes. With punches that were more likely to cause tableting failure, our system predicted the effects of lubricant quantity in the tablet formulation and the occurrence of sticking in the rotary tableting machine.

Evaluation of the ease of taking mini-tablets compared with other tablet formulations in healthy volunteers.

Science.gov (United States)

Hayakawa, Yoshiyuki; Uchida, Shinya; Namiki, Noriyuki

2016-03-10

"Mini-tablets" (MTs) are tablets of diameter≤3mm and have been widely studied and developed. However, reports comparing MTs with other tablet formulations are few. We wished to evaluate the ease of taking a MT quantitatively in comparison with an orally disintegrating mini-tablet (ODMT), conventional tablet (CT) and conventional orally disintegrating tablet (ODT). Four types of tablets were prepared. We prepared tablets of two diameters (3mm for MTs and ODMTs vs. 8mm for CTs and ODTs) and two formulations (MTs and CTs vs. ODMTs and ODTs). Our randomized crossover trial in 18 healthy volunteers (8 men and 10 women; mean age, 22.5years) indicated that the visual analog scale (VAS) score for the ease and amount of water required for intake of MTs was significantly lower than those of CTs. An ODMT required the least amount of water and smallest VAS score for the ease of taking a tablet. Our results showed that the advantage of MTs with regard to the ease of taking and decreased amount of water required was exerted for a unit of dosing comprising tablets. These data suggested the usefulness of MTs and the importance of the number of MTs for comfortable consumption by patients. Copyright © 2015. Published by Elsevier B.V.

Compounding rifampin suspensions with improved injectability for nasogastric enteral feeding tube administration.

Science.gov (United States)

de Villiers, Melgardt M; Vogel, Laura; Bogenschutz, Monica C; Fingerhut, Bonnie J; D'Silva, Joseph B; Moore, Anne

2010-01-01

Often medications that have to be administered to patients via a nasogastric enteral feeding tubes are only available as tablets and capsules with no suitable commercial liquid alternatives. In such situations, pharmacists and nurses have to compound the tablets and capsule contents into liquid suspension formulations for dosing. The risk of occlusion of the enteral tubes during administration is reduced by employing liquid suspensions that are composed of small and uniform particles, not subject to rapid rates of settling, resistant to caking, and easily and uniformly re-suspended upon agitation. Present techniques often employ a manual process, such as a mortar and pestle, to accomplish the particle size reduction and subsequent incorporation into a suitable liquid diluent. A new compounding device has been invented that employs an automated wet-milling process in a single-use disposable plastic container to compound the suspensions. The two processes were compared using Rifampin capsules and various liquid diluents. A prototype version of the new device was employed in the experiments. The physical characteristics of the compounded suspensions were evaluated by determining sedimentation rate, sedimentation volume, and particle size and shape using laser light scattering, optical microscopy, and scanning electron microscopy techniques. The use characteristic of the compounded suspensions was evaluated using a nasogastric tube inject ability test. The results indicated that suspensions prepared using the new device were more resistant to sedimentation and caking and were easier to re-disperse into a uniform mixture by gentle shaking. The results were a consequence of the particles generated by the new device which were found to be smaller and more uniform in shape and size. The suspensions prepared using the new device did not cause blockage of the enteral feeding tubes in comparison to those prepared using a mortar and pastle. In conclusion, the results indicate

Gradient high performance liquid chromatography method for simultaneous determination of ilaprazole and its related impurities in commercial tablets

Directory of Open Access Journals (Sweden)

Shang Wang

2015-04-01

Full Text Available A methodology (HPLC proposed in this paper for simultaneously quantitative determination of ilaprazole and its related impurities in commercial tablets was developed and validated. The chromatographic separation was carried out by gradient elution using an Agilent C8 column (4.6 mm × 250 mm, 5 μm which was maintained at 25 °C. The mobile phase composed of solvent A (methanol and solvent B (solution consisting 0.02 mmol/l monopotassium phosphate and 0.025 mmol/l sodium hydroxide was at a flow rate of 1.0 ml/min. The samples were detected and quantified at 237 nm using an ultraviolet absorbance detector. Calibration curves of all analytes from 0.5 to 3.5 μg/ml were good linearity (r ≥ 0.9990 and recovery was greater than 99.5% for each analyte. The lower limit of detection (LLOD and quantification (LOQ of this analytical method were 10 ng/ml and 25 ng/ml for all impurities, respectively. The stress studies indicated that the degradation products could not interfere with the detection of ilaprazole and its related impurities and the assay can thus be considered stability-indicating. The method precisions were in the range of 0.41–1.21 while the instrument precisions were in the range of 0.38–0.95 in terms of peak area RSD% for all impurities, respectively. This method is considered stability-indicating and is applicable for accurate and simultaneous measuring of the ilaprazole and its related impurities in commercial enteric-coated tablets.

Effect of repeated compaction of tablets on tablet properties and work of compaction using an instrumented laboratory tablet press.

Science.gov (United States)

Gamlen, Michael John Desmond; Martini, Luigi G; Al Obaidy, Kais G

2015-01-01

The repeated compaction of Avicel PH101, dicalcium phosphate dihydrate (DCP) powder, 50:50 DCP/Avicel PH101 and Starch 1500 was studied using an instrumented laboratory tablet press which measures upper punch force, punch displacement and ejection force and operates using a V-shaped compression profile. The measurement of work compaction was demonstrated, and the test materials were ranked in order of compaction behaviour Avicel PH101 > DCP/Avicel PH101 > Starch > DCP. The behaviour of the DCP/Avicel PH101 mixture was distinctly non-linear compared with the pure components. Repeated compaction and precompression had no effect on the tensile fracture strength of Avicel PH101 tablets, although small effects on friability and disintegration time were seen. Repeated compaction and precompression reduced the tensile strength and the increased disintegration time of the DCP tablets, but improved the strength and friability of Starch 1500 tablets. Based on the data reported, routine laboratory measurement of tablet work of compaction may have potential as a critical quality attribute of a powder blend for compression. The instrumented press was suitable for student use with minimal supervisor input.

Teach yourself visually Fire tablets

CERN Document Server

Marmel, Elaine

2014-01-01

Expert visual guidance to getting the most out of your Fire tablet Teach Yourself VISUALLY Fire Tablets is the comprehensive guide to getting the most out of your new Fire tablet. Learn to find and read new bestsellers through the Kindle app, browse the app store to find top games, surf the web, send e-mail, shop online, and much more! With expert guidance laid out in a highly visual style, this book is perfect for those new to the Fire tablet, providing all the information you need to get the most out of your device. Abundant screenshots of the Fire tablet graphically rich, touch-based Androi

Development of modified-release tablets of zolpidem tartrate by biphasic quick/slow delivery system.

Science.gov (United States)

Mahapatra, Anjan Kumar; Sameeraja, N H; Murthy, P N

2015-06-01

Zolpidem tartrate is a non-benzodiazepine analogue of imidazopyridine of sedative and hypnotic category. It has a short half-life with usual dosage regimen being 5 mg, two times a day, or 10 mg, once daily. The duration of action is considered too short in certain circumstances. Thus, it is desirable to lengthen the duration of action. The formulation design was implemented by preparing extended-release tablets of zolpidem tartrate using the biphasic delivery system technology, where sodium starch glycolate acts as a superdisintegrant in immediate-release part and hydroxypropyl methyl cellulose as a release retarding agent in extended-release core. Tablets were prepared by direct compression. Both the core and the coat contained the drug. The pre-compression blends were evaluated for angle of repose, bulk density, and compressibility index. The tablets were evaluated for thickness, hardness, weight variation test, friability, and in vitro release studies. No interaction was observed between zolpidem tartrate and excipients from the Fourier transform infrared spectroscopy and differential scanning calorimetry analysis. The results of all the formulations prepared were compared with reference product Stilnoct®. Optimized formulations showed release patterns that match the United States Pharmacopeia (USP) guidelines for zolpidem tartrate extended-release tablets. The mechanism of drug release was studied using different mathematical models, and the optimized formulation has shown Fickian diffusion. Accelerated stability studies were performed on the optimized formulation.

In vitro disintegration and dissolution studies of once-weekly copies of alendronate sodium tablets (70 mg) and in vivo implications.

Science.gov (United States)

Dansereau, Richard J; Crail, Debbie J; Perkins, Alan C

2008-04-01

The aim of this study was to evaluate the in vitro disintegration and dissolution of 26 alendronic acid tablets (70 mg) on the market in Canada, Germany, the Netherlands, and the United Kingdom compared to the branded product (Fosamax). The disintegration and dissolution times were determined using the methods described in the United States Pharmacopeia 30 (USP 30). The disintegration of four orally disintegrating tablets (non-bisphosphonates) and branded film-coated risedronate sodium tablets were included for comparison. The mean disintegration times of the alendronic acid tablets ranged from 14 s for Pharmachemie (Netherlands) to 342 s (5.7 min) for Betapharm (Germany). The mean disintegration time of the branded product tablets ranged from 43 to 78 s. Six of the 26 companies market alendronic acid tablets with very rapid disintegration times which are similar to those of orally disintegrating tablets (non-bisphosphonates). The alendronic acid tablets with very rapid mean disintegration times are as follows: Pharmachemie (Netherlands), 14 s; Novopharm (Canada), 13-24 s; GRY-Pharma (Germany), 21 s; Juta Pharma (Germany), 30 s; APS/Teva (United Kingdom), 26 and 37 s; and Teva (UK), 14-29 s. Since there is no established disintegration time for alendronic acid tablets there can be no assurance that the copy tablets are equivalent to the branded product in terms of esophageal drug exposure. However, the in vitro disintegration times have not been correlated with in vivo disintegration and performance. The dissolution of all the bisphosphonate tablets was rapid with greater than 80% dissolved in 15 min and all products conformed to the USP 30 specification. The dissolution of all alendronic acid tablets was rapid and complete and conformed to the established USP 30 specifications which should ensure adequate drug absorption from the copy products. However, copies of alendronic acid tablets are approved based on the results of single-dose bioavailability studies in

Can Tablet Computers Enhance Faculty Teaching?

Science.gov (United States)

Narayan, Aditee P; Whicker, Shari A; Benjamin, Robert W; Hawley, Jeffrey; McGann, Kathleen A

2015-06-01

Learner benefits of tablet computer use have been demonstrated, yet there is little evidence regarding faculty tablet use for teaching. Our study sought to determine if supplying faculty with tablet computers and peer mentoring provided benefits to learners and faculty beyond that of non-tablet-based teaching modalities. We provided faculty with tablet computers and three 2-hour peer-mentoring workshops on tablet-based teaching. Faculty used tablets to teach, in addition to their current, non-tablet-based methods. Presurveys, postsurveys, and monthly faculty surveys assessed feasibility, utilization, and comparisons to current modalities. Learner surveys assessed perceived effectiveness and comparisons to current modalities. All feedback received from open-ended questions was reviewed by the authors and organized into categories. Of 15 eligible faculty, 14 participated. Each participant attended at least 2 of the 3 workshops, with 10 to 12 participants at each workshop. All participants found the workshops useful, and reported that the new tablet-based teaching modality added value beyond that of current teaching methods. Respondents developed the following tablet-based outputs: presentations, photo galleries, evaluation tools, and online modules. Of the outputs, 60% were used in the ambulatory clinics, 33% in intensive care unit bedside teaching rounds, and 7% in inpatient medical unit bedside teaching rounds. Learners reported that common benefits of tablet computers were: improved access/convenience (41%), improved interactive learning (38%), and improved bedside teaching and patient care (13%). A common barrier faculty identified was inconsistent wireless access (14%), while no barriers were identified by the majority of learners. Providing faculty with tablet computers and having peer-mentoring workshops to discuss their use was feasible and added value.

Comparison of tadalafil pharmacokinetics after administration of a new orodispersible film versus a film-coated tablet

Directory of Open Access Journals (Sweden)

Park SI

2018-04-01

Full Text Available Sang-In Park,1,* Su-Hak Heo,2,3,* Gihwan Kim,2 Seokhoon Chang,2 Keon-Hyoung Song,3 Min-Gul Kim,4 Eun-Heui Jin,5 JaeWoo Kim,5 SeungHwan Lee,1 Jang Hee Hong5,6 1Department of Clinical Pharmacology and Therapeutics, Seoul National University College of Medicine and Hospital, Seoul, Republic of Korea; 2R&D Center, C.L. Pharm Co., Ltd, Seoul, Republic of Korea; 3Department of Pharmaceutical Engineering, College of Medical Science, Soonchunhyang University, Asan, Republic of Korea; 4Department of Pharmacology, School of Medicine, Chonbuk National University, Jeonju, Republic of Korea; 5Clinical Trials Center, Chungnam National University Hospital, Daejeon, Republic of Korea; 6Department of Pharmacology, College of Medicine, Chungnam National University, Daejeon, Republic of Korea *These authors contributed equally to this work Background: An orodispersible film (ODF of tadalafil may provide increased convenience for erectile dysfunction (ED patients as compared to conventional tablet formulations. In this study, we aimed to compare the pharmacokinetic, safety, and tolerability profiles of a newly developed ODF formulation of tadalafil to those of a film-coated tablet (FCT of tadalafil.Materials and methods: This study was conducted in healthy male subjects using an open-label, randomized sequence, two-period, two-formulation, single-dose, crossover design. The subjects were randomly assigned to one of two sequences of the two formulations: both the test drug (ODF and the reference drug (FCT contained 20 mg of tadalafil. Blood samples were collected up to 72 h after administration. Plasma concentrations of tadalafil were analyzed using liquid chromatography–tandem mass spectrometry. Geometric mean ratios (GMRs of the ODF to FCT formulations and their 90% CIs for the pharmacokinetic parameters were estimated. Safety and tolerability were assessed throughout the study.Results: Forty healthy male subjects were enrolled, and 36 of these completed the

Specifications development for "Karbatril" codenamed tablets

Directory of Open Access Journals (Sweden)

L. I. Kucherenko

2017-08-01

Full Text Available Introduction. According to current legislation of Ukraine the specifications of tablets include the following indicators: description, identification, average weight, disintegration and assay. The aim of the study. The development of specifications and project of quality control methods for "Karbatril" codenamed tablets. Materials and methods. During the study we analyzed 6 series of tablets "Karbatril." For the description, identification, determination of the average mass, disintegration, active ingredients quantify of "Karbatril" codenamed tablets we used appropriate methods and instruments. Results and discussion. Tablets "Karbatril" were analyzed for the following parameters: - Overview - Tablets white or nearly white; - Average weight - during the study the average weight of 6 series of obtained tablets ranged from 339,0 mg to 369,9 mg according to SPU from 337,0 mg to 373,0 mg; - Disintegration – according to SPU the disintegration for tablet without shell shall not exceed 15 min. Analyzed tablets disintegrated in the period from 5 to 10 minutes; - Identification and quantification of the active ingredients of tablets were conducted using modified HPLC methods. During the identification obtained chromatograms show compliance with SPU. In quantitative determination of the active ingredients content in "Karbatril" codenamed tablets we found carbamazepine from 148.18 mg to 150.19 mg, thiotriazoline - from 98.93 mg to 99.71 mg. This data is consistent to SPU which regulates content of carbamazepine - 150 mg ± 7,5%, thiotriazoline - 100 mg ± 10%. Conclusions. This study has developed specification for "Karbatril" codenamed tablets and also methods of HPLC qualitative and quantitative determination of active ingredients. In the specification the following parameters are included: description, identification, average weight, disintegration and assay. The study drafted quality control methods which are planned to be later offered to the

Microstructure of Tablet-Pharmaceutical Significance, Assessment, and Engineering.

Science.gov (United States)

Sun, Changquan Calvin

2017-05-01

To summarize the microstructure - property relationship of pharmaceutical tablets and approaches to improve tablet properties through tablet microstructure engineering. The main topics reviewed here include: 1) influence of material properties and manufacturing process parameters on the evolution of tablet microstructure; 2) impact of tablet structure on tablet properties; 3) assessment of tablet microstructure; 4) development and engineering of tablet microstructure. Microstructure plays a decisive role on important pharmaceutical properties of a tablet, such as disintegration, drug release, and mechanical strength. Useful information on mechanical properties of a powder can be obtained from analyzing tablet porosity-pressure data. When helium pycnometry fails to accurately measure true density of a water-containing powder, non-linear regression of tablet density-pressure data is a useful alternative method. A component that is more uniformly distributed in a tablet generally exerts more influence on the overall tablet properties. During formulation development, it is highly recommended to examine the relationship between any property of interest and tablet porosity when possible. Tablet microstructure can be engineered by judicious selection of formulation composition, including the use of the optimum solid form of the drug and appropriate type and amount of excipients, and controlling manufacturing process.

Grasp interaction with tablets

CERN Document Server

Wolf, Katrin

2015-01-01

This book presents guidelines for a future device type: a tablet that allows ergonomic front- and back-of-device interaction. These guidelines help designers and developers of user interfaces to build ergonomic applications for tablet devices, in particular for devices that enable back-of-device interaction. In addition, manufacturers of tablet devices obtain arguments that back-of-device interaction is a promising extension of the interaction design space and results in increased input capabilities, enriched design possibilities, and proven usability. The guidelines are derived from empirical studies and developed to fit the users’ skills to the way the novel device type is held. Three particular research areas that are relevant to develop design guidelines for tablet interaction are investigated: ergonomic gestures, interaction areas, and pointing techniques.

Desenvolvimento de formulações e tecnologia de obtenção de comprimidos revestidos de efavirenz: terapia anti-HIV Development of formulations and technology of efavirenz coated tablets obtention: anti-HIV therapy

Directory of Open Access Journals (Sweden)

Osnir de Sá Viana

2006-12-01

Full Text Available O efavirenz é uma das mais recentes classes de agentes anti-retrovirais aplicados no tratamento de infecções por HIV. Está entre os medicamentos de primeira escolha no tratamento da AIDS. Como o efavirenz possui característica hidrofóbica, baixa densidade e oferece grande resistência ao escoamento, a escolha de uma formulação adequada deste fármaco é essencial no desenvolvimento dos comprimidos e para garantir melhor disponibilização no trato gastrointestinal, de forma a alcançar a biodisponibilidade e o efeito terapêutico desejados. Neste trabalho, apresentamos, de forma lógica, o desenvolvimento tecnológico de comprimidos revestidos de efavirenz, levando em consideração suas características físicas e físico-químicas. Os núcleos (comprimidos de efavirenz foram obtidos utilizando-se a técnica de granulação por via úmida. No revestimento por película utilizou-se Opadry® Y-1-7000 em sistema aquoso. Os parâmetros adotados para avaliação física dos comprimidos seguiram as especificações farmacopéicas oficiais e a determinação quantitativa foi realizada mediante método analítico desenvolvido e validado.Efavirenz is one of the most recent classes of anti-retroviral drugs used in the treatment of HIV infections. It is the first choice therapy for AIDS treatment. As efavirenz detains hydrofobic characteristic, low density and offers great resistance to draining, it has been essential to choose an adequated formulation for it, in order to guarantee drug's availability in gastro-intestinal tract, achieving bioavailability and expected therapeutical effects. This work presents efavirez coated tablets thecnological development, considering the physics and physico-chemical characteristics of this drug. The efavirez nucleus (tablets has been obtained employing granulation technics by humid via. In the coating by film, Opadry Y-1-7000 in aquous system was used. The adopted parameters to tablet phisics evaluation

Interchangeability and comparative effectiveness between generic and brand montelukast immediate release tablets after a single oral administration in healthy volunteers.

Science.gov (United States)

Zaid, Abdel Naser; Mousa, Ayman; Ghazal, Nadia; Bustami, Rana

2015-01-01

Montelukast is a leukotriene receptor antagonist. The release of leukotrienes causes narrowing and constricting in the respiratory airways. Blocking the action of these leukotrienes, montelukast can be used for the prophylaxis and treatment of chronic asthma. The aim of this study was to evaluate the interchangeability and comparative effectiveness between a generic and a brand montelukast 10 mg immediate release tablets (Broncast(®) and Singulair(®), respectively) after a single oral dose among Arab Mediterranean volunteers. An open-label, randomized two-period crossover bioequivalence design was conducted in 31 healthy male volunteers with a 1 week washout between each study period and under fasting conditions. The plasma drug concentration was assessed by using a previously validated LC MS/MS method. The ratio between the generic and brand of geometric least squares means was reported for both generic and brand products. Moreover, an in vitro dissolution study was conducted on generic and brand tablets using three different pH media, and similarity and non-similarity factors (f2 and f1) were calculated. The used bioanalytical method was found to be linear within the range 6.098-365.855 ng/mL. The correlation coefficient was close to 0.999 during the course of the study validation. Statistical comparison of the main pharmacokinetic parameters showed the inexistence of any significant difference between generic and the brand. The point estimates (ratios of geometric means) were 111.939, 111.711, and 112.169 % for AUC0-24, AUC0-∞, and Cmax, respectively. The 90 % confidence intervals (CIs) were within the pre-defined limits of 80.00-125.00 % as specified by the FDA and EMA for bioequivalence studies. F2 and f1 were higher than 50 and lower than 15, respectively in all selected pH media. Broncast(®) immediate release film coated tablets (10 mg/tablet) are bioequivalent to Singulair(®) immediate release film coated tablets (10 mg/tablet), with a

Preparation of venlafaxine hydrochloride sustained-release tablets

Directory of Open Access Journals (Sweden)

GUO Lingling

2013-08-01

Full Text Available To prepare venlafxine hydrochloride sustained-release tablets.Hydroxypropylmethyl cellulose(HPMC and methyl cellulose(MC were used as main materials to prepare sustained-release tablets of velafaxine hydrochloride and the influence of important factors on in vitro release curves of venlafaxine hydrochloride sustained-release tablets was investigated.Results:The optimal prescription included 100 mg HPMC,25 mg MC,and 2.5% glidant in one tablet prepared with 30kN.The tablets were prepared with the method of wet granulation by NO.16 mesh sieve.The tablets exhibited good sustained-release property in phosphate buffered solution (pH=6.8.The as-prepared venlafxine hydrochloride sustained-release tablets have good sustained-release property.

Integrated Application of Quality-by-Design Principles to Drug Product Development: A Case Study of Brivanib Alaninate Film-Coated Tablets.

Science.gov (United States)

Badawy, Sherif I F; Narang, Ajit S; LaMarche, Keirnan R; Subramanian, Ganeshkumar A; Varia, Sailesh A; Lin, Judy; Stevens, Tim; Shah, Pankaj A

2016-01-01

Modern drug product development is expected to follow quality-by-design (QbD) paradigm. At the same time, although there are several issue-specific examples in the literature that demonstrate the application of QbD principles, a holistic demonstration of the application of QbD principles to drug product development and control strategy, is lacking. This article provides an integrated case study on the systematic application of QbD to product development and demonstrates the implementation of QbD concepts in the different aspects of product and process design for brivanib alaninate film-coated tablets. Using a risk-based approach, the strategy for development entailed identification of product critical quality attributes (CQAs), assessment of risks to the CQAs, and performing experiments to understand and mitigate identified risks. Quality risk assessments and design of experiments were performed to understand the quality of the input raw materials required for a robust formulation and the impact of manufacturing process parameters on CQAs. In addition to the material property and process parameter controls, the proposed control strategy includes use of process analytical technology and conventional analytical tests to control in-process material attributes and ensure quality of the final product. Copyright © 2016. Published by Elsevier Inc.

COMPARISON OF HYDROCORTISONE 10 MG TABLETS: TABLET HARDNESS OPTIMISED FOR ADULT USE HAS NEGATIVE CONSEQUENCES FOR PAEDIATRIC USE.

Science.gov (United States)

Saimbi, Sarina; Madden, Valerie; Stirling, Heather; Yahyouche, Asma; Batchelor, Hannah

2016-09-01

Children's medicines are not always readily available as an age appropriate product and manipulation of adult products is often required. Recently the commercial manufacturing process for 10 mg hydrocortisone tablets has changed and the compression force increased due to tablets fracturing on removal from the blister pack. However, this change led to parents of children requiring hydrocortisone reporting that the tablets were more difficult to manipulate.This study evaluated 10 mg hydrocortisone tablets for their suitability for manipulation in order to deliver an appropriate dose to children (2 mg dose). The physical properties of tablets with the old and new compression force were compared as well as the accuracy of obtaining the paediatric dose. The tablets compared were hydrocortisone Auden 10 mg tablets (Brand A, PL16876/002)-these are the newer, harder tablets- and hydrocortisone 10 mg tablets (Brand B, PL17507/0097). Tablet physical properties including friability (Copley FRV200) and tablet hardness (Copley TBF1000) were compared. The accuracy of split doses (halve and quarter tablets) were recorded on a Sartorius analytical balance. The accuracy of the 2 mg paediatric dosing was assessed by crushing the tablet, adding 10 mL of water and extracting 2 mL. The concentration was measured using UV analysis (Jenway Genova Plus) according to a calibration curve (wavelength=246 nm). Two devices were used to crush the tablets: a spoon onto a plate and a commercially available crushing device (Apothecary Ezy Crush Pill Crusher With Ergo Grip). As anticipated Brand A tablets were harder (51.85 ±5.1 N) compared to Brand B (30.99±4.1 N). Brand A tablets passed the friability testing with Auden tablets which are known to be harder tablets and therefore more force is required to crush these. Some of the experimental work within this project was conducted by Andrew Hackett and Kameron Paul-Thaper whilst at the University of Birmingham on work

Evaluation of in-line Raman data for end-point determination of a coating process: Comparison of Science-Based Calibration, PLS-regression and univariate data analysis.

Science.gov (United States)

Barimani, Shirin; Kleinebudde, Peter

2017-10-01

A multivariate analysis method, Science-Based Calibration (SBC), was used for the first time for endpoint determination of a tablet coating process using Raman data. Two types of tablet cores, placebo and caffeine cores, received a coating suspension comprising a polyvinyl alcohol-polyethylene glycol graft-copolymer and titanium dioxide to a maximum coating thickness of 80µm. Raman spectroscopy was used as in-line PAT tool. The spectra were acquired every minute and correlated to the amount of applied aqueous coating suspension. SBC was compared to another well-known multivariate analysis method, Partial Least Squares-regression (PLS) and a simpler approach, Univariate Data Analysis (UVDA). All developed calibration models had coefficient of determination values (R 2 ) higher than 0.99. The coating endpoints could be predicted with root mean square errors (RMSEP) less than 3.1% of the applied coating suspensions. Compared to PLS and UVDA, SBC proved to be an alternative multivariate calibration method with high predictive power. Copyright © 2017 Elsevier B.V. All rights reserved.

A critical review on tablet disintegration.

Science.gov (United States)

Quodbach, Julian; Kleinebudde, Peter

2016-09-01

Tablet disintegration is an important factor for drug release and can be modified with excipients called tablet disintegrants. Tablet disintegrants act via different mechanisms and the efficacy of these excipients is influenced by various factors. In this review, the existing literature on tablet disintegration is critically reviewed. Potential disintegration mechanisms, as well as impact factors on the disintegration process will be discussed based on experimental evidence. Search terms for Scopus and Web of Science included "tablet disintegration", "mechanism tablet disintegration", "superdisintegrants", "disintegrants", "swelling force", "disintegration force", "disintegration mechanisms", as well as brand names of commonly applied superdisintegrants. References of identified papers were screened as well. Experimental data supports swelling and shape recovery as main mechanisms of action of disintegrants. Other tablet excipients and different manufacturing techniques greatly influence the disintegration process. The use of different excipients, experimental setups and manufacturing techniques, as well as the demand for original research led to a distinct patchwork of knowledge. Broader, more systematic approaches are necessary not only to structure the past but also future findings.

A pilot trial on subjects with lactose and/or oligosaccharides intolerance treated with a fixed mixture of pure and enteric-coated α- and ß-galactosidase

Directory of Open Access Journals (Sweden)

Di Pierro F

2015-02-01

Full Text Available Francesco Di Pierro,1 Alexander Bertuccioli,2 Eleonora Marini,3 Leandro Ivaldi4 1Velleja Research, Milan, Italy; 2Italian Association Fitness and Medicine, Fano, PU, Italy; 3Pharmextracta, Pontenure, Piacenza, Italy; 4Digestive Endoscopic Department, Ceva Hospital, Ceva, Cuneo, Italy Aim: Lactose and complex carbohydrates maldigestion, common food intolerances due to low gut content of α- and ß-galactosidase, lead to abdominal symptoms including pain, diarrhea, bloating, flatulence, and cramping. Commonly, intolerant patients are advised by physicians to avoid the offending foods (dairy foods, cereals, beans, etc. This food-limiting option, however, has possible nutritional risks. We have therefore evaluated the impact of using pure, enteric-coated α- plus ß-galactosidase on gut symptoms in intolerant subjects instead of avoidance of the offending foods. Methods: Sixteen subjects intolerant to lactose and/or complex carbohydrates were enrolled and evaluated in terms of gut symptoms with 1 uncontrolled diet, 2 diet devoid of offending foods, and 3 uncontrolled diet along with pure, enteric-coated α- and ß-galactosidase (DDM Galactosidase®. Results: Even with the uncontrolled diet, intolerant subjects treated with DDM Galactosidase® exhibited reduced gut symptoms (bloating, flatulence, diarrhea, and constipation significantly better than the control treatment as well as having a diet devoid of offending foods. Conclusion: DDM Galactosidase® is a valid and safe optional treatment to counteract lactose and complex carbohydrate intolerance in subjects who prefer not to avoid, at least partially, offending foods. Keywords: lactase, lactose intolerance, complex carbohydrate intolerance

Amorphization within the tablet

DEFF Research Database (Denmark)

Doreth, Maria; Hussein, Murtadha Abdul; Priemel, Petra A.

2017-01-01

, the feasibility of microwave irradiation to prepare amorphous solid dispersions (glass solutions) in situ was investigated. Indomethacin (IND) and polyvinylpyrrolidone K12 (PVP) were tableted at a 1:2 (w/w) ratio. In order to study the influence of moisture content and energy input on the degree of amorphization......, tablet formulations were stored at different relative humidity (32, 43 and 54% RH) and subsequently microwaved using nine different power-time combinations up to a maximum energy input of 90 kJ. XRPD results showed that up to 80% (w/w) of IND could be amorphized within the tablet. mDSC measurements...

Android tablets for dummies

CERN Document Server

Gookin, Dan

2015-01-01

Learn all you need to know about your Android tablet in one quick and easy reference! It's not a computer and it's not a smartphone-so what in the world is it? Whether you're new to Android or new to tablets altogether, you're about to experience mobile computing like never before with this fun, full-color guide! Inside, longtime and bestselling author Dan Gookin walks you through setting up your Android tablet, navigating the interface, browsing the web, setting up email, connecting to social media, finding plenty of apps, music, books, and movies to indulge your interests-and so much more.

Tablet-Based Functional MRI of the Trail Making Test: Effect of Tablet Interaction Mode

Directory of Open Access Journals (Sweden)

Mahta Karimpoor

2017-10-01

Full Text Available The Trail Making Test (TMT is widely used for assessing executive function, frontal lobe abilities, and visual motor skills. Part A of this pen-and-paper test (TMT-A involves linking numbers randomly distributed in space, in ascending order. Part B (TMT-B alternates between linking numbers and letters. TMT-B is more demanding than TMT-A, but the mental processing that supports the performance of this test remains incompletely understood. Functional MRI (fMRI may help to clarify the relationship between TMT performance and brain activity, but providing an environment that supports real-world pen-and-paper interactions during fMRI is challenging. Previously, an fMRI-compatible tablet system was developed for writing and drawing with two modes of interaction: the original cursor-based, proprioceptive approach, and a new mode involving augmented reality to provide visual feedback of hand position (VFHP for enhanced user interaction. This study characterizes the use of the tablet during fMRI of young healthy adults (n = 22, with half of the subjects performing TMT with VFHP and the other half performing TMT without VFHP. Activation maps for both TMT-A and TMT-B performance showed considerable overlap between the two tablet modes, and no statistically differences in brain activity were detected when contrasting TMT-B vs. TMT-A for the two tablet modes. Behavioral results also showed no statistically different interaction effects for TMT-B vs. TMT-A for the two tablet modes. Tablet-based TMT scores showed reasonable convergent validity with those obtained by administering the standard pen-and-paper TMT to the same subjects. Overall, the results suggest that despite the slightly different mechanisms involved for the two modes of tablet interaction, both are suitable for use in fMRI studies involving TMT performance. This study provides information for using tablet-based TMT methods appropriately in future fMRI studies involving patients and healthy

Deposition of coatings on Ti by sputtering of tableted carbonate-hydroxylapatite in HF discharge plasma

International Nuclear Information System (INIS)

Khamchukov, Y.D.; Klubovich, V.; Potapenko, I.

2001-01-01

The coatings of carbonate-hydroxyapatite (CHA) on materials suitable for implants must have, because of their shielding functions, sufficiently large thickness and good adhesion. For these reasons, the production of these coatings is a technological task whose solution may be obtained on the basis of the application of different ion-plasma technologies. Examination of the properties of the CHA coatings on the substrate of titanium and the effect on the materials of the coating and the substrate of ion-plasma technology with the application of high-frequency discharge was the aim of this investigation

Clinical study on influences of enteric coated aspirin on blood pressure and blood pressure variability.

Science.gov (United States)

Ji, A-L; Chen, W-W; Huang, W-J

2016-12-01

We investigated the effects of oral administration of enteric coated aspirin (ASA) on blood pressure and blood pressure variability of hypertension patients before sleep. We observed 150 hypertension cases, classified as Grade 1-2, from September 2006 to March 2008. They are divided into a control group with 30 cases, ASA I group with 60 cases and ASA II group with 60 cases randomly. Subjects in the control group had proper diets, were losing weight, exercising and maintaining a healthy mentality and were taking 30 mg Adalat orally once a day. Based on the treatment of control group, patients in ASA I group were administered 0.1 g Bayaspirin (produced by Bayer Company) at drought in the morning. Also, based on the treatment of control group, patients in ASA II group were administered 0.1 g Bayaspirin at draught before sleep. The course of treatment is 3 months and then after the treatment, decreasing blood pressure and blood pressure variability conditions in three groups will be compared. Through the comparison of ASA II group with the control group, they have differences in terms of systolic blood pressure (SBP), diastolic blood pressure (DBP), decreasing range of blood pressure and blood pressure variability (p sleep has synergistic effects on decreasing blood pressure of hypertension patients and improving blood pressure variability.

Multivariate modelling of the tablet manufacturing process with wet granulation for tablet optimization and in-process control

NARCIS (Netherlands)

Westerhuis, J.A; Coenegracht, P.M J; Lerk, C.F

1997-01-01

The process of tablet manufacturing with granulation is described as a two-step process. The first step comprises wet granulation of the powder mixture, and in the second step the granules are compressed into tablets. For the modelling of the pharmaceutical process of wet granulation and tableting,

Evaluation of the performance characteristics of bilayer tablets: Part II. Impact of environmental conditions on the strength of bilayer tablets.

Science.gov (United States)

Kottala, Niranjan; Abebe, Admassu; Sprockel, Omar; Bergum, James; Nikfar, Faranak; Cuitiño, Alberto M

2012-12-01

Ambient air humidity and temperature are known to influence the mechanical strength of tablets. The objective of this work is to understand the influence of processing parameters and environmental conditions (humidity and temperature) on the strength of bilayer tablets. As part of this study, bilayer tablets were compressed with different layer ratios, dwell times, layer sequences, material properties (plastic and brittle), first and second layer forces, and lubricant concentrations. Compressed tablets were stored in stability chambers controlled at predetermined conditions (40C/45%RH, 40C/75%RH) for 1, 3, and 5 days. The axial strength of the stored tablets was measured and a statistical model was developed to determine the effects of the aforementioned factors on the strength of bilayer tablets. As part of this endeavor, a full 3 × 2(4) factorial design was executed. Responses of the experiments were analyzed using PROC GLM of SAS (SAS Institute Inc, Cary, North Carolina, USA). A model was fit using all the responses to determine the significant interactions (p < 0.05). Results of this study indicated that storage conditions and storage time have significant impact on the strength of bilayer tablets. For Avicel-lactose and lactose-Avicel tablets, tablet strength decreased with the increasing humidity and storage time. But for lactose-lactose tablets, due to the formation of solid bridges upon storage, an increase in tablet strength was observed. Significant interactions were observed between processing parameters and storage conditions on the strength of bilayer tablets.

A novel multivariate approach using science-based calibration for direct coating thickness determination in real-time NIR process monitoring.

Science.gov (United States)

Möltgen, C-V; Herdling, T; Reich, G

2013-11-01

This study demonstrates an approach, using science-based calibration (SBC), for direct coating thickness determination on heart-shaped tablets in real-time. Near-Infrared (NIR) spectra were collected during four full industrial pan coating operations. The tablets were coated with a thin hydroxypropyl methylcellulose (HPMC) film up to a film thickness of 28 μm. The application of SBC permits the calibration of the NIR spectral data without using costly determined reference values. This is due to the fact that SBC combines classical methods to estimate the coating signal and statistical methods for the noise estimation. The approach enabled the use of NIR for the measurement of the film thickness increase from around 8 to 28 μm of four independent batches in real-time. The developed model provided a spectroscopic limit of detection for the coating thickness of 0.64 ± 0.03 μm root-mean square (RMS). In the commonly used statistical methods for calibration, such as Partial Least Squares (PLS), sufficiently varying reference values are needed for calibration. For thin non-functional coatings this is a challenge because the quality of the model depends on the accuracy of the selected calibration standards. The obvious and simple approach of SBC eliminates many of the problems associated with the conventional statistical methods and offers an alternative for multivariate calibration. Copyright © 2013 Elsevier B.V. All rights reserved.

Using a Virtual Tablet Machine to Improve Student Understanding of the Complex Processes Involved in Tablet Manufacturing.

Science.gov (United States)

Mattsson, Sofia; Sjöström, Hans-Erik; Englund, Claire

2016-06-25

Objective. To develop and implement a virtual tablet machine simulation to aid distance students' understanding of the processes involved in tablet production. Design. A tablet simulation was created enabling students to study the effects different parameters have on the properties of the tablet. Once results were generated, students interpreted and explained them on the basis of current theory. Assessment. The simulation was evaluated using written questionnaires and focus group interviews. Students appreciated the exercise and considered it to be motivational. Students commented that they found the simulation, together with the online seminar and the writing of the report, was beneficial for their learning process. Conclusion. According to students' perceptions, the use of the tablet simulation contributed to their understanding of the compaction process.

Relationships between response surfaces for tablet characteristics of placebo and API-containing tablets manufactured by direct compression method.

Science.gov (United States)

Hayashi, Yoshihiro; Tsuji, Takahiro; Shirotori, Kaede; Oishi, Takuya; Kosugi, Atsushi; Kumada, Shungo; Hirai, Daijiro; Takayama, Kozo; Onuki, Yoshinori

2017-10-30

In this study, we evaluated the correlation between the response surfaces for the tablet characteristics of placebo and active pharmaceutical ingredient (API)-containing tablets. The quantities of lactose, cornstarch, and microcrystalline cellulose were chosen as the formulation factors. Ten tablet formulations were prepared. The tensile strength (TS) and disintegration time (DT) of tablets were measured as tablet characteristics. The response surfaces for TS and DT were estimated using a nonlinear response surface method incorporating multivariate spline interpolation, and were then compared with those of placebo tablets. A correlation was clearly observed for TS and DT of all APIs, although the value of the response surfaces for TS and DT was highly dependent on the type of API used. Based on this knowledge, the response surfaces for TS and DT of API-containing tablets were predicted from only two and four formulations using regression expression and placebo tablet data, respectively. The results from the evaluation of prediction accuracy showed that this method accurately predicted TS and DT, suggesting that it could construct a reliable response surface for TS and DT with a small number of samples. This technique assists in the effective estimation of the relationships between design variables and pharmaceutical responses during pharmaceutical development. Copyright © 2017 Elsevier B.V. All rights reserved.

Touch Screen Tablets and Emergent Literacy

Science.gov (United States)

Neumann, Michelle M.; Neumann, David L.

2014-01-01

The use of touch screen tablets by young children is increasing in the home and in early childhood settings. The simple tactile interface and finger-based operating features of tablets may facilitate preschoolers' use of tablet application software and support their educational development in domains such as literacy. This article reviews…

Formulation and evaluation of taste mask pellets of granisetron hydrochloride as oro dispersible tablet

Directory of Open Access Journals (Sweden)

Nilesh Choudhary

2015-09-01

Full Text Available Orally disintegrating systems have carved a niche amongst the oral drug delivery systems due to the highest compliance of the patients, especially the geriatrics and pediatrics. In addition, patients suffering from dysphagia, motion sickness, repeated emesis and mental disorders prefer these medications because they cannot swallow large quantity of water. Further, drugs exhibiting satisfactory absorption from the oral mucosa or intended for immediate pharmacological action can be advantageously formulated in these dosage forms. However, the requirements of formulating these dosage forms with mechanical strength sufficient to withstand the rigors of handling and capable of disintegrating within a few seconds on contact with saliva are inextricable. The purpose of this research was to mask the bitter taste of granisetron hydrochloride. To mask the taste Kollicoat(r Smartseal 30D was used as coating polymer for pellet coating. The coated pellets of the drug was directly compressed with different superdisintegrant as AC-Di-Sol, Explotab and Kollidon CL in different concentration 5.0-7.5% w/w into an ODT. The prepared tablets were evaluated for hardness, friability, weight variation, wetting time, wet absorption ratio, in-vitro disintegration time and in vitro dissolution studies. Tablets exhibited quick disintegration characteristics with Kollidon CL in concentration 7.5% w/w i.e., within 20 seconds, which is characteristic of orally disintegrating dosage forms. More than 98% of drug was released from the formulations within 15 minutes. Formulations subjected to stability testing as per the ICH guidelines for 3 months, indicated stability with no change in taste, hardness, drug content, disintegration time and dissolution profiles. Thus, the results conclusively demonstrated successful masking of taste and rapid disintegration of the formulated dosage forms in the oral cavity.

Ghost tablet in feces.

Science.gov (United States)

Iwamuro, Masaya; Morishita, Yosuke; Urata, Haruo; Okada, Hiroyuki

2017-12-01

Recently, we encountered a female patient who identified the presence of a ghost tablet in her fecal matter. Interestingly, although the patient was prescribed potassium chloride capsules, elemental composition analysis by energy-dispersive X-ray spectroscopy was unable to detect the presence of either potassium or chloride in the fecal tablet remnant.

Suberin fatty acids isolated from outer birch bark improve moisture barrier properties of cellulose ether films intended for tablet coatings.

Science.gov (United States)

Heinämäki, Jyrki; Halenius, Anna; Paavo, Maaja; Alakurtti, Sami; Pitkänen, Pauliina; Pirttimaa, Minni; Paaver, Urve; Kirsimäe, Kalle; Kogermann, Karin; Yliruusi, Jouko

2015-07-15

We showed that the addition of suberin fatty acids (SFAs) even at small concentrations significantly improves the water vapor barrier properties of hydroxypropyl methylcellulose (HPMC) films. SFAs were isolated from the outer birch bark using extractive hydrolysis. The effects of SFAs on the film formation of aqueous HPMC were investigated with free films plasticized with polyethylene glycol (PEG 400). Special attention was paid on the physical solid-state, moisture barrier and mechanical stress-strain properties of films intended for tablet film coatings. Topography and surface morphology, glass transition temperature (Tg), tensile strength, Young's modulus, and water vapor permeation (WVP) of films were studied. The addition of SFAs lowered the Tg of films suggesting partial enhancement in film plasticization. The WVP of films decreased with increasing SFAs concentration up to 15% (calculated as a % w/w from a polymer weight). The WVP value for a non-suberized reference film and suberized film plasticized with PEG 400 was 2.13×10(-6) and 0.69[×10(-6) g/(mm(2)×h)×mm/Pa], respectively. The addition of SFAs impaired the mechanical stress-strain properties of HPMC films by reducing the deformation capacity of film. In conclusion, the film properties and performance of aqueous HPMC can be modified by including SFAs in the films. Copyright © 2015 Elsevier B.V. All rights reserved.

21 CFR 520.812 - Enrofloxacin tablets.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Enrofloxacin tablets. 520.812 Section 520.812 Food... DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.812 Enrofloxacin tablets. (a) Specifications. Each tablet contains either 22.7, 68.0, or 136.0 milligrams of enrofloxacin. (b) Sponsor. See No...

'Tablet burden' in patients with metastatic breast cancer.

Science.gov (United States)

Milic, Marina; Foster, Anna; Rihawi, Karim; Anthoney, Alan; Twelves, Chris

2016-03-01

The implications for patients with cancer, of the 'tablet burden' resulting from increasing use of oral anticancer drugs and medication for co-morbidities have not previously been well explored. We sought to (i) quantify tablet burden in women with metastatic breast cancer (MBC), (ii) establish which groups of drug contribute most to this burden and (iii) gain insight into patients' attitudes towards oral anti-cancer treatment. One hundred patients with MBC anonymously completed a questionnaire describing their medication histories and attitudes towards their tablets. The patients (mean age 60, range 31-95) were all female and taking a median of six tablets (range 0-31) daily; 37 patients were taking >10 tablets. Oral anticancer treatment constituted the category of treatment taken by the highest proportion of patients, followed by symptomatic cancer treatments, proton pump inhibitors and cardiovascular medication. Numerically, however, symptomatic drugs accounted for 44% of all tablets and specific anti-cancer treatment for 15%; medication not directly related to the cancer accounted for the remaining 40% of tablets. A quarter of patients reported inconvenience in taking their tablets, the main reason being tablet size and one third reported forgetting their tablets at least once a week. Nearly two thirds of patients expressing a preference favoured oral anticancer treatment, the commonest reason being greater convenience. Tablet burden is considerable for many patients with MBC and can be problematic. A significant proportion of tablets represent treatment for co-morbidities, the significance of which may be questionable in women with MBC. Copyright © 2015 Elsevier Ltd. All rights reserved.

Tablet telerounding.

Science.gov (United States)

Kaczmarek, Bartosz F; Trinh, Quoc-Dien; Menon, Mani; Rogers, Craig G

2012-12-01

To evaluate the feasibility of remote rounding using commercially available standard tablets with videoconferencing system and assess patient satisfaction. Thirty-two patients with at least 2 postoperative days of hospital stay after robotic urologic procedures were included in the study. On the first postoperative day, the physician-patient encounter was performed as telerounding with videoconferencing due to the physician's duties scheduled in another affiliated hospital. On the second day, the personal bedside encounter took place. The tablet we used was an iPad2 (Apple, iOS 5.1; Apple, Cupertino, CA) with a videoconferencing application. A telerounding satisfaction survey was fulfilled by all patients on the touchscreen of the tablet. Average time of telerounding encounter was 4.5 minutes (range, 1.0-13.5 minutes), average age of the patient was 57.7 years (range, 19-80 years), and 19 were men (59%). Patients expressed a high level of satisfaction with 91% of patients stating that their care was better using telerounding and 97% of patients stating that telerounding should be a regular part of patient care in the hospital. Additionally, 94% of patients stated that they could easily communicate with their doctor over the telerounding system, 84% of patients agreed that they would feel comfortable with telerounding daily if they were hospitalized again and 81% of patients would prefer telerounding communication with their doctor than be directly seen by another doctor. Tablet telerounding using videoconferencing can be a strong supplementing tool in doctor-patient communication. It is convenient for the physician and increases the patient's hospital stay satisfaction. Copyright © 2012 Elsevier Inc. All rights reserved.

Principles of Tablet Computing for Educators

Science.gov (United States)

Katzan, Harry, Jr.

2015-01-01

In the study of modern technology for the 21st century, one of the most popular subjects is tablet computing. Tablet computers are now used in business, government, education, and the personal lives of practically everyone--at least, it seems that way. As of October 2013, Apple has sold 170 million iPads. The success of tablets is enormous and has…

Using Tablet on Education

Science.gov (United States)

Algoufi, Rateeba

2016-01-01

Technological advancements in digital devices have made educational methodology to adopt new strategies and procedures to suit the Mobile learning era. Mobile devices such as tablets are growing to be the focus of research studies and educational use around the globe in the present day. With the influence of handy computing tablets in the hands of…

Bioequivalence of a single 400-mg dose of imatinib 100-mg oral tablets and a 400-mg tablet in healthy adult Korean volunteers.

Science.gov (United States)

Lee, Hae Won; Seong, Sook Jin; Park, Sung Min; Lee, Joomi; Gwon, Mi-Ri; Kim, Hyun-Ju; Lim, Sung Mook; Lim, Mi-Sun; Kim, Woomi; Yang, Dong Heon; Yoon, Young-Ran

2015-06-01

Imatinib mesylate (IM) is a selective tyrosine kinase inhibitor for the treatment of chronic myeloid leukemia and gastrointestinal stromal tumors. A new once-daily 400-mg film-coated tablet of imatinib has been developed by a pharmaceutical company in Korea. The present study was designed to assess and compare the PK parameters, bioavailability, and bioequivalence of the new imatinib 400-mg formulation (test) versus the conventional 100-mg formulation (reference) administered as a single 400-mg dose in healthy adult male volunteers. This randomized, open-label, single-dose, two-way crossover study was conducted in healthy Korean male volunteers. Eligible subjects were randomly assigned in a 1 : 1 ratio to receive 400 mg of the test (one 400-mg tablet) or reference (four 100-mg tablets) formulation, followed by a 2-week washout period and administration of the alternate formulation. Serial blood samples were collected at 0 (predose), 0.5, 1, 1.5, 2, 2.5, 3, 4, 6, 8, 10, 12, 24, 48, and 72 hours after administration. Plasma imatinib concentrations were determined using liquid chromatography coupled with tandem mass spectrometry. The formulations were to be considered bioequivalent if the 90% confidence intervals (CIs) of the adjusted geometric mean ratios for Cmax, AUC(0-t), and AUC(0-∞)ž were within the predetermined range of 0.80 - 1.25. In total, 35 subjects completed the study. No serious adverse event was reported during the study. The 90% CIs of the adjusted geometric mean ratios of the test formulation to the reference formulation for C(max), AUC(0-t) and AUC(0-∞)ž of imatinib were all within the bioequivalence criteria range of 0.8 - 1.25. The test formulation of imatinib met the Korean regulatory requirements for bioequivalence. Both imatinib formulations were well-tolerated in all subjects.

Evaluation of tableting and tablet properties of Kollidon SR: the influence of moisture and mixtures with theophylline monohydrate.

Science.gov (United States)

Hauschild, Karsten; Picker-Freyer, Katharina M

2006-02-01

The aim of the study was firstly to investigate the influence of moisture on the tableting and tablet properties of Kollidon SR and secondly to investigate the influence of theophylline monohydrate on the tableting behavior and tablet properties produced from binary mixtures with Kollidon SR. In comparison to Kollidon SR, microcrystalline cellulose (MCC) was used. The glass transition temperature (Tg) of the powder over the whole range of RH (0-90%), and in addition, the Tg of tablets of Kollidon SR were measured. Densities and flowability of the powders were analyzed. The tablets were produced at five different maximum relative densities (rho(rel), max) on an instrumented eccentric tableting machine. They were produced at three different relative humidities (RH), 30%, 45%, and 60% RH for the pure substances and binary mixtures with different ratios of drug and excipient were tableted at 45% RH. The tableting properties were analyzed by 3D modeling, force-displacement profiles, and compactibility plots. First, the Tg of the powder decreased with increasing RH and the Tg of the tablet was 4-8 K lower than the powder. The predominant deformation of Kollidon SR is plastic deformation and Kollidon SR showed a higher compactibility than MCC. The parameters of the 3D model showed an extreme change between 45 and 60% RH, and at higher RH more and more particles deformed elastically. This was confirmed by analysis of force-displacement profiles. At 60% RH, the radial tensile strength of the Kollidon SR tablets was half of the radial tensile strength at 45% RH. The reason is a higher relative energy of plastic deformation than for MCC. This results in a better utilization of the energy to deform the powder into a tablet and the exceeding of the glass transition temperature at higher RH. In conclusion, at 60% RH at the same rho(rel, max), tableting and tablet properties of Kollidon SR are extremely changed since plasticity is significantly higher. In the second part of the

Tablet-Aided BehavioraL intervention EffecT on Self-management skills (TABLETS) for Diabetes.

Science.gov (United States)

Lynch, Cheryl P; Williams, Joni S; J Ruggiero, Kenneth; G Knapp, Rebecca; Egede, Leonard E

2016-03-22

Multiple randomized controlled trials (RCTs) show that behavioral lifestyle interventions are effective in improving diabetes management and that comprehensive risk factor management improves cardiovascular disease (CVD) outcomes. The role of technology has been gaining strong support as evidence builds of its potential to improve diabetes management; however, evaluation of its impact in minority populations is limited. This study intends to provide early evidence of a theory-driven intervention, Tablet-Aided BehavioraL intervention EffecT on Self-management skills (TABLETS), using real-time videoconferencing for education and skills training. We examine the potential for TABLETS to improve health risk behaviors and reduce CVD risk outcomes among a low-income African American (AA) population with poorly controlled type 2 diabetes. The study is a two-arm, pilot controlled trial that randomizes 30 participants to the TABLETS intervention and 30 participants to a usual care group. Blinded outcome assessments will be completed at baseline, 2.5 months (immediate post-intervention), and 6.5 months (follow-up). The TABLETS intervention consists of culturally tailored telephone-delivered diabetes education and skills training delivered via videoconferencing on tablet devices, with two booster sessions delivered via tablet-based videoconferencing at 3 months and 5 months to stimulate ongoing use of the tablet device with access to intervention materials via videoconferencing slides and a manual of supplementary materials. The primary outcomes are physical activity, diet, medication adherence, and self-monitoring behavior, whereas the secondary outcomes are HbA1c, low-density lipoprotein cholesterol (LDL-C), BP, CVD risk, and quality of life. This study provides a unique opportunity to assess the feasibility and efficacy of a theory-driven, tablet-aided behavioral intervention that utilizes real-time videoconferencing technology for education and skills training on self

A bioequivalence study of two tamsulosin sustained-release tablets in Indonesian healthy volunteers.

Science.gov (United States)

Prasaja, Budi; Harahap, Yahdiana; Lusthom, Windy; Setiawan, Evy C; Ginting, Mena B; Hardiyanti; Lipin

2011-06-01

The bioavailability of two 0.4 mg tamsulosin sustained-release film-coated tablet formulations was compared; using generic tablets (Prostam(®)) as test formulation and the originator product as reference formulation. Twenty-four subjects were included in this single-dose, open-label, randomized two-way crossover design following an overnight fasting. A one-week wash-out period was applied. Blood samples were drawn up to 72 h following drug administration. Plasma concentration of tamsulosin was determined by liquid chromatography-tandem mass spectrometry method with TurboIonSpray mode. Pharmacokinetic parameters AUC(0-t,) AUC(0-∞), C (max) and t (½) were determined and used for bioequivalence evaluation after log-transformation, whereas t (max) ratios were evaluated non-parametrically. The estimated point and 90% confidence intervals (CI) for AUC(0-t,) AUC(0-∞), C (max) and t (½) were 109.55% (96.41-124.49%), 109.94% (96.85-124.81%), 105.87% (92.88-120.67%) and 100.00% (90.56-110.43%), respectively. These results indicated that the two formulations of tamsulosin were bioequivalent; therefore they may be prescribed interchangeably.

21 CFR 520.434 - Chlorphenesin carbamate tablets.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Chlorphenesin carbamate tablets. 520.434 Section 520.434 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... Chlorphenesin carbamate tablets. (a) Specifications. Each tablet contains 400 milligrams of chlorphenesin...

Stage control of tablets manufacturing

Directory of Open Access Journals (Sweden)

L. I. Kucherenko

2014-08-01

Full Text Available Today in Ukraine tuberculosis is the wide-spread infectious disease causing the death in most cases; about 700 thousand persons are suffering from it. In Ukraine epidemic of tuberculosis is progressing and spreading. In spite of all protective measures three inhabitants of our country contract tuberculosis per hour, every hour one patient dies and in common about 1.5% of the population is ill with tuberculosis. Isoniazid is antituberculous drug of the first line and it is the most effective one. Chemotherapy of tuberculosis requests long-lasting administration of antituberculous drugs that causes high risk of side effects. To prevent or lessen side effects of antituberculous medicines antioxidants use in complex therapy is perspective. Fulfilled investigations showed efficacy of combining two medical substances – isoniazid andthiotriazolin – in one dosage form. Objective.The aim of our investigation is working out the methods of standardization, in particularquantitative determination of isoniazid andthiotriazolin content in tablet mass by high-performance liquid chromatography (HPLC. Materials and Methods.During in-process investigations combined tableted remedy containing isoniazid andthiotriazolin and proper amount of adjuvants has been developed (it contains active substances isoniazid – 0.2 g,thiotriazolin – 0.05 g and adjuvants up to the 0.4 g of the tablet. During stage control of tablets manufacturingspecial attention is paid to the control of tablet mass quality. Especially it concerns quantitative determination of active substances in it. More and more attention is paid to modern physical-chemical methods of standardization in up-to-date analysis of drug products, such as ultraviolet spectrometry, high-performance liquid chromatography (HPLC etc. In previous scientific investigations we proved the possibility of standardization of active substances artificial compound by HPLC method and optimal conditions of analysis performing

Medication Errors in Patients with Enteral Feeding Tubes in the Intensive Care Unit.

Science.gov (United States)

Sohrevardi, Seyed Mojtaba; Jarahzadeh, Mohammad Hossein; Mirzaei, Ehsan; Mirjalili, Mahtabalsadat; Tafti, Arefeh Dehghani; Heydari, Behrooz

2017-01-01

Most patients admitted to Intensive Care Units (ICU) have problems in using oral medication or ingesting solid forms of drugs. Selecting the most suitable dosage form in such patients is a challenge. The current study was conducted to assess the frequency and types of errors of oral medication administration in patients with enteral feeding tubes or suffering swallowing problems. A cross-sectional study was performed in the ICU of Shahid Sadoughi Hospital, Yazd, Iran. Patients were assessed for the incidence and types of medication errors occurring in the process of preparation and administration of oral medicines. Ninety-four patients were involved in this study and 10,250 administrations were observed. Totally, 4753 errors occurred among the studied patients. The most commonly used drugs were pantoprazole tablet, piracetam syrup, and losartan tablet. A total of 128 different types of drugs and nine different oral pharmaceutical preparations were prescribed for the patients. Forty-one (35.34%) out of 116 different solid drugs (except effervescent tablets and powders) could be substituted by liquid or injectable forms. The most common error was the wrong time of administration. Errors of wrong dose preparation and administration accounted for 24.04% and 25.31% of all errors, respectively. In this study, at least three-fourth of the patients experienced medication errors. The occurrence of these errors can greatly impair the quality of the patients' pharmacotherapy, and more attention should be paid to this issue.

Tablets for Learning in Higher Education

DEFF Research Database (Denmark)

Godsk, Mikkel

Based on a small-scale literature review this paper identifies the top 10 affordances of post PC tablets (sometimes referred to as ‘tablet computers’) for higher education in settings where the technology is used for learning. The review shows that the predominant affordances of the technology...... are related to its ability to support engaging, inclusive, and/or collaborative learning, to provide flexibility in place, and to include multimedia and interactive content in teaching practice. However, performing the review also revealed that the notion of tablets for learning is equivocal. As a consequence......, the concepts of tabletcasts and tabletcasting are introduced as one possible framing for future research on tablets as an educational technology....

Lattice-Boltzmann Simulation of Tablet Disintegration

Science.gov (United States)

Jiang, Jiaolong; Sun, Ning; Gersappe, Dilip

Using the lattice-Boltzmann method, we developed a 2D model to study the tablet disintegration involving the swelling and wicking mechanisms. The surface area and disintegration profile of each component were obtained by tracking the tablet structure in the simulation. Compared to pure wicking, the total surface area is larger for swelling and wicking, which indicates that the swelling force breaks the neighboring bonds. The disintegration profiles show that the tablet disintegrates faster than pure wicking, and there are more wetted active pharmaceutical ingredient particles distributed on smaller clusters. Our results indicate how the porosity would affect the disintegration process by changing the wetting area of the tablet as well as by changing the swelling force propagation.

Attitudes towards Smart Phones and Tablets

Directory of Open Access Journals (Sweden)

Ali Akbar Ansarin

2017-07-01

Full Text Available This paper examines the perceptions of advantages of smart phones and tablets on basic and general English students' language learning, self-sufficiency, and interest using smart phones and tablets at an Iranian university college during one university term. Through a survey administered to 333 basic and general English students and through selective observations and interviews, the following questions were examined: 1 Students' perceived impact of smart phones and tablets on increasing their confidence throughout the course,2  Students’ perceived comfort/enjoyment with smart phones and tablets for the students at the beginning and end of the semester,3 Students' perceived impact of devices through a comparison between pre and post survey measures on improvement of reading comprehension, reading speed, vocabulary and spelling, motivation, and preparing them for class tests and quizzes. Tablets were evaluated more positively than smart phones by the students as a means to increase confidence. Both tablets and smart phones were evaluated positively, both as a means of improving students’ motivation to learn, and as a means to develop reading comprehension, spelling, and vocabulary. However, students’ expectations regarding the impact of such devices on their reading speed, preparation for tests and quizzes, as well as comfort and enjoyment were not met.

21 CFR 520.1409 - Methylprednisolone, aspirin tablets.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Methylprednisolone, aspirin tablets. 520.1409... Methylprednisolone, aspirin tablets. (a) Specifications. Each tablet contains 0.5 milligram of methylprednisolone and 300 milligrams of aspirin. (b) Sponsor. See No. 000009 in § 510.600(c) of this chapter. (c) NAS/NRC...

21 CFR 520.1157 - Iodinated casein tablets.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Iodinated casein tablets. 520.1157 Section 520...) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS ORAL DOSAGE FORM NEW ANIMAL DRUGS § 520.1157 Iodinated casein tablets. (a) Specifications. Each 1-gram tablet contains 25 milligrams of iodinated casein. (b) Sponsor...

Tablet surface characterisation by various imaging techniques

DEFF Research Database (Denmark)

Seitavuopio, Paulus; Rantanen, Jukka; Yliruusi, Jouko

2003-01-01

The aim of this study was to characterise tablet surfaces using different imaging and roughness analytical techniques including optical microscopy, scanning electron microscopy (SEM), laser profilometry and atomic force microscopy (AFM). The test materials compressed were potassium chloride (KCl......) and sodium chloride (NaCl). It was found that all methods used suggested that the KCl tablets were smoother than the NaCl tablets and higher compression pressure made the tablets smoother. Imaging methods like optical microscopy and SEM can give useful information about the roughness of the sample surface...

Evaluation of Certain Pharmaceutical Quality Attributes of Lisinopril Split Tablets

Directory of Open Access Journals (Sweden)

Khairi M. S. Fahelelbom

2016-10-01

Full Text Available Tablet splitting is an accepted practice for the administration of drugs for a variety of reasons, including dose adjustment, ease of swallowing and cost savings. The purpose of this study was to evaluate the physical properties of lisinopril tablets as a result of splitting the tablets either by hand or with a splitting device. The impact of the splitting technique of lisinopril (Zestril® tablets, 20 mg on certain physical parameters such as weight variation, friability, disintegration, dissolution and drug content were studied. Splitting the tablets either by hand or with a splitter resulted in a minute but statistically significant average weight loss of <0.25% of the tablet to the surrounding environment. The variability in the weight of the hand-split tablet halves was more pronounced (37 out of 40 tablet halves varied by more than 10% from the mean weight than when using the tablet splitter (3 out of 40 tablet halves. The dissolution and drug content of the hand-split tablets were therefore affected because of weight differences. However, the pharmacopoeia requirements for friability and disintegration time were met. Hand splitting of tablets can result in an inaccurate dose and may present clinical safety issues, especially for drugs with a narrow therapeutic window in which large fluctuations in drug concentrations are undesirable. It is recommended to use tablets with the exact desired dose, but if this is not an option, then a tablet splitter could be used.

Tablet splitting: is it worthwhile? Analysis of drug content and weight uniformity for half tablets of 16 commonly used medications in the outpatient setting.

Science.gov (United States)

Helmy, Sally A

2015-01-01

Tablet splitting is a well-established medical practice in clinical settings for multiple reasons, including cost savings and ease of swallowing. However, it does not necessarily result in weight-uniform half tablets. To (a) investigate the effect of tablet characteristics on weight and content uniformity of half tablets, resulting from splitting 16 commonly used medications in the outpatient setting and (b) provide recommendations for safe tablet-splitting prescribing practices. Ten random tablets from each of the selected medications were weighed and split by 5 volunteers (2 men and 3 women aged 25-44 years) using a knife. The selected medications were mirtazapine 30 mg, bromazepam 3 mg, oxcarbazepin 150 mg, sertraline 50 mg, carvedilol 25 mg, bisoprolol fumarate 10 mg, losartan 50 mg, digoxin 0.25 mg, amiodarone HCl 200 mg, metformin HCl 1,000 mg, glimepiride 4 mg, montelukast 10 mg, ibuprofen 600 mg, celecoxib 200 mg, meloxicam 15 mg, and sildenafil citrate 50 mg. The resulting half tablets were evaluated for weight and drug content uniformity in accordance with proxy United States Pharmacopeia (USP) specification (95%-105% for digoxin and 90%-110% for the other 15 drugs). Weight and drug content uniformity were assessed by comparing weight or drug content of the half tablets with one-half of the mean weight or drug content for all whole tablets in the sample. The percentages by which the weight and drug content of each whole tablet or half tablet differed from sample mean values were calculated. Other relevant physical characteristics of the 16 products were measured. A total of 52 of 320 half tablets (16.2%) and 48 of 320 half tablets (15.0%) fell outside of the proxy USP specification for weight and drug content, respectively. Bromazepam, carvedilol, bisoprolol, losartan, digoxin, and meloxicam half tablets failed the weight and content uniformity test; however, the half tablets for the rest of the medications passed the test. Mean percent weight loss after

Optical and terahertz measurement techniques for flat-faced pharmaceutical tablets: a case study of gloss, surface roughness and bulk properties of starch acetate tablets

International Nuclear Information System (INIS)

Juuti, M; Tuononen, H; Kontturi, V; Peiponen, K-E; Prykäri, T; Alarousu, E; Myllylä, R; Kuosmanen, M; Ketolainen, J

2009-01-01

Surface and bulk properties of flat-faced starch acetate tablets were studied. For surface quality inspection optical coherence tomography and recently developed diffractive glossmeter were utilized. Both these optical devices together provide local information on surface roughness and gloss of a tablet over a measured area. The concepts of mean topography and mean gloss profile for surface quality of a tablet are introduced. It was observed that the surface quality of the tablet varies, and compression at high pressure may not guarantee a good surface quality of the tablet. Using novel statistical parameters for gloss and relevant surface roughness parameter, it is possible to get more comprehensive quantitative data on the surface condition of a tablet. THz spectrometer was utilized for detection of THz pulse delay in transmission measurement mode from the tablets. The delay time and thickness ratio of the tablet are consistent with the porosity of the tablet as a function of compression pressure. We suggest that the multimeasurement scheme using three different devices helps tablet makers to better assess bulk and surface quality of their products

Orodispersible tablets containing taste-masked solid lipid pellets with metformin hydrochloride: Influence of process parameters on tablet properties.

Science.gov (United States)

Petrovick, Gustavo Freire; Kleinebudde, Peter; Breitkreutz, Jörg

2018-01-01

Compaction of multiparticulates into tablets, particularly into orodispersible tablets (ODTs), is challenging. The compression of pellets, made by solid lipid extrusion/spheronization processes, presents peculiar difficulties since solid lipids usually soften or melt at relatively low temperature ranges and due to applied mechanical forces. Until now, there are no reports in literature about the development of ODTs based on solid lipid pellets. To investigate the feasibility of producing such tablets, a design of experiment (DoE) approach was performed to elucidate the influence of compression force and amount of two co-processed excipients (Ludiflash ® and Parteck ® ODT) on properties of the tablets (friability, tensile strength, and disintegration time). ODTs (15 mm, flat-faced) with solid lipid pellets (250-1000 µm in diameter) containing 500 mg of metformin HCl, presenting immediate drug release profile and taste-masked properties, were targeted. During compression, a strong lamination of the tablets containing Parteck ® ODT was observed. This phenomenon was prominently observed when high compression forces (≥5 kN) and high excipient amounts (≥40%; w/w) were used. On the other hand, the DoE focused on tablets with Ludiflash ® showed better results regarding the production of ODTs. A positive influence of the compression force on the tensile strength and disintegration time of the tablets, regarding specifications of the Ph. Eur., was observed. The increase in the amount of this excipient resulted in fast disintegrating tablets, however, a negative influence on the tensile strength was noticed. After optimization of the parameters and formulation, based on the DoE results and considering the Ph. Eur. specifications for tablets, ODTs based on lipid pellets containing metformin HCl presenting immediate release profile (85% drug release in less than 30 min) and taste-masked properties (determined by an electronic tongue) were successfully

[Effect of Tongluo Xingnao effervescent tablets on learning and memory dysfunction in rats with chronic cerebral ischemia].

Science.gov (United States)

Hu, Yong; Ju, Shao-Hua; Zhang, Yin-Jie; Xiong, Min; Xu, Shi-Jun; Ma, Yun-Tong; Zhong, Zhen-Dong

2014-05-01

To study the effect of Tongluo Xingnao effervescent tablets on learning and memory capacity and expression of Na(+)-K(+)-ATPase in hippocampus of rats with chronic cerebral ischemia-induced learning and memory dysfunction model. The 2-VO method was used to establish sd rat model learning and memory dysfunction induced by chronic cerebral ischemia. The 50 rats in the successfully established model were randomly divided into the model control group, the Dihydroergotoxine Mesylate tablets group (0.7 mg x kg(-1), Tongluo Xingnao effervescent tablets high dose (7.56 g x kg(-1)), middle dose (3.78 g x kg(-1)) and low dose (1.59 g x kg(-1)) groups and the sham operation group (n = 10) as the control group. The groups were orally given 10 ml x kg(-1) x d(-1) drugs for consecutively 90 days. On the 86th day, Morris water maze was adopted for them. On the 90th day, a leaning and memory capacity test was held. The brain tissues were fixed with 10% formaldehyde and observed for pathomorphism after routine slide preparation and staining. The expression of hippocampal Na(+)-K(+)-ATPase was detected with immunohistochemistry and image quantitative analysis. Compared with the model group, all of Tongluo Xingnao effervescent tablets groups showed significant decrease in the escape latency at the 5th day in the Morris water maze, and notable increase in the frequency of the first quadrant dwell, the frequency passing the escape platform and the frequency entering effective area (p tablets can improve the learning and memory capacity, reduce pathological changes of hippocampal tissues of rats with chronic cerebral ischemia-induced learning and memory dysfunction model, and promote the expression of Na(+)-K(+)-ATPase in hippocampus.

Systematic evaluation of common lubricants for optimal use in tablet formulation.

Science.gov (United States)

Paul, Shubhajit; Sun, Changquan Calvin

2018-05-30

As an essential formulation component for large-scale tablet manufacturing, the lubricant preserves tooling by reducing die-wall friction. Unfortunately, lubrication also often results in adverse effects on tablet characteristics, such as prolonged disintegration, slowed dissolution, and reduced mechanical strength. Therefore, the choice of lubricant and its optimal concentration in a tablet formulation is a critical decision in tablet formulation development to attain low die-wall friction while minimizing negative impact on other tablet properties. Three commercially available tablet lubricants, i.e., magnesium stearate, sodium stearyl fumerate, and stearic acid, were systematically investigated in both plastic and brittle matrices to elucidate their effects on reducing die-wall friction, tablet strength, tablet hardness, tablet friability, and tablet disintegration kinetics. Clear understanding of the lubrication efficiency of commonly used lubricants as well as their impact on tablet characteristics would help future tablet formulation efforts. Copyright © 2018 Elsevier B.V. All rights reserved.

In vitro dissolution of proton-pump inhibitor products intended for paediatric and geriatric use in physiological bicarbonate buffer.

Science.gov (United States)

Liu, Fang; Shokrollahi, Honaz

2015-05-15

Proton-pump inhibitor (PPI) products based on enteric coated multiparticulates are design to meet the needs of patients who cannot swallow tablets such as children and older adults. Enteric coated PPI preparations exhibit delays in in vivo absorption and onset of antisecretory effects, which is not reflected by the rapid in vitro dissolution in compendial pH 6.8 phosphate buffer commonly used for assessment of these products. A more representative and physiological medium, pH 6.8 mHanks bicarbonate buffer, was used in this study to evaluate the in vitro dissolution of enteric coated multiparticulate-based PPI products. Commercially available omeprazole, lansoprazole and esomeprazole products were subject to dissolution tests using USP-II apparatus in pH 4.5 phosphate buffer saline for 45 min (acid stage) followed by pH 6.8 phosphate buffer or pH 6.8 mHanks bicarbonate buffer. In pH 6.8 phosphate buffer, all nine tested products displayed rapid and comparable dissolution profiles meeting the pharmacopeia requirements for delayed release preparations. In pH 6.8 mHanks buffer, drug release was delayed and failed the pharmacopeia requirements from most enteric coated preparations. Despite that the same enteric polymer, methacrylic acid-ethyl acrylate copolymer (1:1), was applied to all commercial multiparticulate-based products, marked differences were observed between dissolution profiles of these preparations. The use of pH 6.8 physiological bicarbonate (mHanks) buffer can serve as a useful tool to provide realistic and discriminative in vitro release assessment of enteric coated PPI preparations and to assist rational formulation development of these products. Copyright © 2015 Elsevier B.V. All rights reserved.

Portable Tablets in Science Museum Learning

DEFF Research Database (Denmark)

Gronemann, Sigurd Trolle

2016-01-01

Despite the increasing use of portable tablets in learning, their impact has received little attention in research. In five different projects, this media-ethnographic and design-based analysis of the use of portable tablets as a learning resource in science museums investigates how young people...... is identified. It is argued that, paradoxically, museums’ decisions to innovate by introducing new technologies, such as portable tablets, and new pedagogies to support them conflict with many young people’s traditional ideas of museums and learning. The assessment of the implications of museums’ integration...... of portable tablets indicates that in making pedagogical transformations to accommodate new technologies, museums risk opposing didactic intention if pedagogies do not sufficiently attend to young learners’ systemic expectations to learning and to their expectations to the digital experience influenced...

Composition profiling of seized ecstasy tablets by Raman spectroscopy.

Science.gov (United States)

Bell, S E; Burns, D T; Dennis, A C; Matchett, L J; Speers, J S

2000-10-01

Raman spectroscopy with far-red excitation has been investigated as a simple and rapid technique for composition profiling of seized ecstasy (MDMA, N-methyl-3,4-methylenedioxyamphetamine) tablets. The spectra obtained are rich in vibrational bands and allow the active drug and excipient used to bulk the tablets to be identified. Relative band heights can be used to determine drug/excipient ratios and the degree of hydration of the drug while the fact that 50 tablets per hour can be analysed allows large numbers of spectra to be recorded. The ability of Raman spectroscopy to distinguish between ecstasy tablets on the basis of their chemical composition is illustrated here by a sample set of 400 tablets taken from a large seizure of > 50,000 tablets that were found in eight large bags. The tablets are all similar in appearance and carry the same logo. Conventional analysis by GC-MS showed they contained MDMA. Initial Raman studies of samples from each of the eight bags showed that despite some tablet-to-tablet variation within each bag the contents could be classified on the basis of the excipients used. The tablets in five of the bags were sorbitol-based, two were cellulose-based and one bag contained tablets with a glucose excipient. More extensive analysis of 50 tablets from each of a representative series of sample bags have distribution profiles that showed the contents of each bag were approximately normally distributed about a mean value, rather than being mixtures of several discrete types. Two of the sorbitol-containing sample sets were indistinguishable while a third was similar but not identical to these, in that it contained the same excipient and MDMA with the same degree of hydration but had a slightly different MDMA/sorbitol ratio. The cellulose-based samples were badly manufactured and showed considerable tablet-to-tablet variation in their drug/excipient ratio while the glucose-based tablets had a tight distribution in their drug/excipient ratios

Optimization of the formulation of fast disintegrating tablets

NARCIS (Netherlands)

Kamp, Herman Vincent van

1987-01-01

Chapter 1 presents general information on tableting and is an introduction to the other chapters. Chapter 2 covers the mechanism of action of tablet disintegrants, in particular modern super disintegrants. The results indicate that when the tablets contain a slightly swelling but hydrophilic

Near-infrared spectroscopy monitoring and control of the fluidized bed granulation and coating processes-A review.

Science.gov (United States)

Liu, Ronghua; Li, Lian; Yin, Wenping; Xu, Dongbo; Zang, Hengchang

2017-09-15

The fluidized bed granulation and pellets coating technologies are widely used in pharmaceutical industry, because the particles made in a fluidized bed have good flowability, compressibility, and the coating thickness of pellets are homogeneous. With the popularization of process analytical technology (PAT), real-time analysis for critical quality attributes (CQA) was getting more attention. Near-infrared (NIR) spectroscopy, as a PAT tool, could realize the real-time monitoring and control during the granulating and coating processes, which could optimize the manufacturing processes. This article reviewed the application of NIR spectroscopy in CQA (moisture content, particle size and tablet/pellet thickness) monitoring during fluidized bed granulation and coating processes. Through this review, we would like to provide references for realizing automated control and intelligent production in fluidized bed granulation and pellets coating of pharmaceutical industry. Copyright © 2017 Elsevier B.V. All rights reserved.

Tablet Keiti: Does it Contain Astronomical Instructions?

DEFF Research Database (Denmark)

Wieczorek, Rafal

2010-01-01

Ethnographic data collected on Easter Island in the late XIX and first half of the XX century suggest that the extant rongorongo tablets contain songs, legends or other chanted traditions. However, we have yet to succeed in relating any one of the rongorongo texts to one of the many legends...... collected by ethnographers. An interesting observation is that, while none of the Rapanuis with whom early visitors to the island were acquainted mentioned anything about astronomy in the context of rongorongo tablets, the only piece of rongorongo texts whose meaning we are certain of is the “calendar...... tablet Mamari”. In the four lines of this tablet, also known as rongorongo text C, we encounter 30 moon glyphs arranged in a pattern that mirrors the Rapa Nui lunar calendar as recorded by early Western visitors. This presentation argues that yet another rongorongo item – tablet Keiti, also known as text...

The accuracy, precision and sustainability of different techniques for tablet subdivision: breaking by hand and the use of tablet splitters or a kitchen knife.

Science.gov (United States)

van Riet-Nales, Diana A; Doeve, Myrthe E; Nicia, Agnes E; Teerenstra, Steven; Notenboom, Kim; Hekster, Yechiel A; van den Bemt, Bart J F

2014-05-15

Tablets are frequently subdivided to lower the dose, to facilitate swallowing by e.g. children or older people or to save costs. Splitting devices are commonly used when hand breaking is difficult or painful. Three techniques for tablet subdivision were investigated: hand breaking, tablet splitter, kitchen knife. A best case drug (paracetamol), tablet (round, flat, uncoated, 500 mg) and operator (24-year student) were applied. Hundred tablets were subdivided by hand and by three devices of each of the following types: Fit & Healthy, Health Care Logistics, Lifetime, PillAid, PillTool, Pilomat tablet splitter; Blokker kitchen knife. The intra and inter device accuracy, precision and sustainability were investigated. The compliance to (adapted) regulatory requirements was investigated also. The accuracy and precision of hand broken tablets was 104/97% resp. 2.8/3.2% (one part per tablet considered; parts right/left side operator). The right/left accuracies of the splitting devices varied between 60 and 133%; the precisions 4.0 and 29.6%. The devices did not deteriorate over 100-fold use. Only hand broken tablets complied with all regulatory requirements. Health care professionals should realize that tablet splitting may result in inaccurate dosing. Authorities should undertake appropriate measures to assure good function of tablet splitters and, where feasible, to reduce the need for their use. Copyright © 2014 The Authors. Published by Elsevier B.V. All rights reserved.

Controlled-release tablet formulation of isoniazid.

Science.gov (United States)

Jain, N K; Kulkarni, K; Talwar, N

1992-04-01

Guar (GG) and Karaya gums (KG) alone and in combination with hydroxy-propylmethylcellulose (HPMC) were evaluated as release retarding materials to formulate a controlled-release tablet dosage form of isoniazid (1). In vitro release of 1 from tablets followed non-Fickian release profile with rapid initial release. Urinary excretion studies in normal subjects showed steady-state levels of 1 for 13 h. In vitro and in vivo data correlated (r = 0.9794). The studies suggested the potentiality of GG and KG as release retarding materials in formulating controlled-release tablet dosage forms of 1.

Pediatric Dispersible Tablets: a Modular Approach for Rapid Prototyping.

Science.gov (United States)

Buck, Jonas; Huwyler, Jörg; Kühl, Peter; Dischinger, Angela

2016-08-01

The design of pediatric formulations is challenging. Solid dosage forms for children have to meet the needs of different ages, e.g. high number of dosing increments and strengths. A modular formulation strategy offering the possibility of rapid prototyping was applied. Different tablet compositions and the resulting tablet characteristics were investigated for dispersible tablets using customized analytical methods. Fluid bed granules were blended with extragranular components, and compressed to tablets. Disintegration behavior was studied with a Texture Analyzer and a Tensiometer. Methods for determination of disintegration time and water uptake of tablets were developed with a Texture Analyzer, and a Tensiometer, respectively. Twenty-two different tablet formulations were prepared and analyzed with respect to disintegration time, hardness, friability, and viscosity. Multivariate data analysis revealed a high impact of type and amount of viscosity enhancer on the disintegration behavior of tablets. An optimized formulation was selected with a disintegration time of 24 s. Methods providing additional information on the disintegration behavior of dispersible tablets compared to standard pharmacopoeia methods were established. Selecting the right type and level of viscosity enhancer and superdisintegrant was critical for developing pediatric tablets with a disintegration time of less than 30 s but still pleasant mouth feel.

Ispaghula Husk-Based Extended Release Tablets of Diclofenac ...

African Journals Online (AJOL)

Purpose: To formulate extended-release tablets of diclofenac sodium based on ispaghula husk. Methods: Tablets with varying proportions of diclofenac sodium and ispaghula husk were formulated by wet granulation technique at a fixed compression force of 10 kN. The formulated tablets were evaluated for ...

Double-layer Tablets of Lornoxicam: Validation of Quantification ...

African Journals Online (AJOL)

Double-layer Tablets of Lornoxicam: Validation of Quantification Method, In vitro Dissolution and Kinetic Modelling. ... Satisfactory results were obtained from all the tablet formulations met compendial requirements. The slowest drug release rate was obtained with tablet cores based on PVP K90 (1.21 mg%.h-1).

The variability of ecstasy tablets composition in Brazil.

Science.gov (United States)

Togni, Loraine R; Lanaro, Rafael; Resende, Rodrigo R; Costa, Jose L

2015-01-01

The content of ecstasy tablets has been changing over the years, and nowadays 3,4-methylenedioxymethamphetamine (MDMA) is not always present in the tablets. The aim of this study was to investigate the chemical composition in the seized tablets labeled as ecstasy. We analyzed samples from 150 different seizures made by Sao Paulo's State Police by gas chromatography-mass spectrometry. MDMA was present in 44.7% of the analyzed samples, and another twenty different active substances were identified in these tablets, such as caffeine, 2C-B, piperazines, amphetamines, phencyclidine, and others. Methamphetamine was present in 22% of these samples. The results demonstrate a huge shift in the pattern of trafficking of synthetic drugs, where MDMA has been replaced in tablets mostly by illicit psychoactive substances, in a clear attempt to bypass the law. The great variability in the tablets composition may lead to an increased risk of drug poisoning. © 2014 American Academy of Forensic Sciences.

Enteric glia.

Science.gov (United States)

Rühl, A; Nasser, Y; Sharkey, K A

2004-04-01

The enteric nervous system is composed of both enteric neurones and enteric glia. Enteric glial cells were first described by Dogiel and are now known to outnumber neurones approximately 4 : 1. In the past, these cells were assumed to subserve a largely supportive role; however, recent evidence indicates that enteric glial cells may play a more active role in the control of gut function. In transgenic mouse models, where enteric glial cells are selectively ablated, the loss of glia results in intestinal inflammation and disruption of the epithelial barrier. Enteric glia are activated specifically by inflammatory insults and may contribute actively to inflammatory pathology via antigen presentation and cytokine synthesis. Enteric glia also express receptors for neurotransmitters and so may serve as intermediaries in enteric neurotransmission. Thus, enteric glia may serve as a link between the nervous and immune systems of the gut and may also have an important role in maintaining the integrity of the mucosal barrier and in other aspects of intestinal homeostasis.

Processing and properties of electrodeposited layered surface coatings

DEFF Research Database (Denmark)

Horsewell, Andy

1998-01-01

Hard chromium, produced by conventional dir ect curl ent (DC) electrodeposition, cannot be deposited to thicknesses gl enter than about 5 mu m because of the buildup of processing stresses which cause channel cracks in the coating. Much thicker chromium coatings map be produced by depositing a la...... geometry is almost always analogous to bending, and fracture resistance is provided through deviation of the channel crack by weak interfaces, resulting in 'terrace cracking'....

Pharmaceutical and analytical evaluation of triphalaguggulkalpa tablets

OpenAIRE

Savarikar, Shreeram S.; Barbhind, Maneesha M.; Halde, Umakant K.; Kulkarni, Alpana P.

2011-01-01

Aim of the Study: Development of standardized, synergistic, safe and effective traditional herbal formulations with robust scientific evidence can offer faster and more economical alternatives for the treatment of disease. The main objective was to develop a method of preparation of guggulkalpa tablets so that the tablets meet the criteria of efficacy, stability, and safety. Materials and Methods: Triphalaguggulkalpa tablet, described in sharangdharsanhita and containing guggul and triphala p...

Electronic acquisition of OSCE performance using tablets

Directory of Open Access Journals (Sweden)

Hochlehnert, Achim

2015-10-01

Full Text Available Background: Objective Structured Clinical Examinations (OSCEs often involve a considerable amount of resources in terms of materials and organization since the scores are often recorded on paper. Computer-assisted administration is an alternative with which the need for material resources can be reduced. In particular, the use of tablets seems sensible because these are easy to transport and flexible to use.Aim: User acceptance concerning the use of tablets during OSCEs has not yet been extensively investigated. The aim of this study was to evaluate tablet-based OSCEs from the perspective of the user (examiner and the student examinee.Method: For two OSCEs in Internal Medicine at the University of Heidelberg, user acceptance was analyzed regarding tablet-based administration (satisfaction with functionality and the subjective amount of effort as perceived by the examiners. Standardized questionnaires and semi-standardized interviews were conducted (complete survey of all participating examiners. In addition, for one OSCE, the subjective evaluation of this mode of assessment was gathered from a random sample of participating students in semi-standardized interviews.Results: Overall, the examiners were very satisfied with using tablets during the assessment. The subjective amount of effort to use the tablet was found on average to be “hardly difficult”. The examiners identified the advantages of this mode of administration as being in particular the ease of use and low rate of error. During the interviews of the examinees, acceptance for the use of tablets during the assessment was also detected.Discussion: Overall, it was found that the use of tablets during OSCEs was well accepted by both examiners and examinees. We expect that this mode of assessment also offers advantages regarding assessment documentation, use of resources, and rate of error in comparison with paper-based assessments; all of these aspects should be followed up on in

Formulation and evaluation of glipizide floating-bioadhesive tablets

Directory of Open Access Journals (Sweden)

Jayvadan K. Patel

2010-10-01

Full Text Available The purpose of this study was formulation and in vitro evaluation of floating-bioadhesive tablets to lengthen the stay of glipizide in its absorption area. Effervescent tablets were made using chitosan (CH, hydroxypropyl methylcellulose (HPMC, carbopolP934 (CP, polymethacrylic acid (PMA, citric acid, and sodium bicarbonate. Tablets with 5% effervescent base had longer lag time than 10%. The type of polymer had no significant effect on the floating lag time. All tablets floated atop the medium for 23-24 hr. Increasing carbopolP934 caused higher bioadhesion than chitosan (p < 0.05. All formulations showed a Higuchi, non-Fickian release mechanism. Tablets with 10% effervescent base, 80% CH/20% HPMC, or 80% CP/20% PMA seemed desirable.

Sodium lauryl sulfate impedes drug release from zinc-crosslinked alginate beads: switching from enteric coating release into biphasic profiles.

Science.gov (United States)

Taha, Mutasem O; Nasser, Wissam; Ardakani, Adel; Alkhatib, Hatim S

2008-02-28

The aim of this research is to investigate the effects of sodium lauryl sulfate (SLS) on ionotropically cross-linked alginate beads. Different levels of SLS were mixed with sodium alginate and chlorpheniramine maleate (as loaded model drug). The resulting viscous solutions were dropped onto aqueous solutions of zinc or calcium ions for ionotropic curing. The generated beads were assessed by their drug releasing profiles, infrared and differential scanning colorimetery (DSC) traits. SLS was found to exert profound concentration-dependent impacts on the characteristics of zinc-crosslinked alginate beads such that moderate modifications in the levels of SLS switched drug release from enteric coating-like behavior to a biphasic release modifiable to sustained-release by the addition of minute amounts of xanthan gum. Calcium cross-linking failed to reproduce the same behavior, probably due to the mainly ionic nature of calcium-carboxylate bonds compared to the coordinate character of their zinc-carboxylate counterparts. Apparently, moderate levels of SLS repel water penetration into the beads, and therefore minimize chlorpheniramine release. However, higher SLS levels seem to discourage polymeric cross-linking and therefore allow biphasic drug release.

Breaking of scored tablets : a review

NARCIS (Netherlands)

van Santen, E; Barends, D M; Frijlink, H W

The literature was reviewed regarding advantages, problems and performance indicators of score lines. Scored tablets provide dose flexibility, ease of swallowing and may reduce the costs of medication. However, many patients are confronted with scored tablets that are broken unequally and with

Feasibility of mini-tablets as a flexible drug delivery tool.

Science.gov (United States)

Mitra, Biplob; Chang, Jessica; Wu, Sy-Juen; Wolfe, Chad N; Ternik, Robert L; Gunter, Thomas Z; Victor, Michael C

2017-06-15

Mini-tablets have potential applications as a flexible drug delivery tool in addition to their generally perceived use as multi-particulates. That is, mini-tablets could provide flexibility in dose finding studies and/or allow for combination therapies in the clinic. Moreover, mini-tablets with well controlled quality attributes could be a prudent choice for administering solid dosage forms as a single unit or composite of multiple mini-tablets in patient populations with swallowing difficulties (e.g., pediatric and geriatric populations). This work demonstrated drug substance particle size and concentration ranges that achieve acceptable mini-tablet quality attributes for use as a single or composite dosage unit. Immediate release and orally disintegrating mini-tablet formulations with 30μm to 350μm (particle size d 90 ) acetaminophen and Compap™ L (90% acetaminophen) at concentrations equivalent to 6.7% and 26.7% acetaminophen were evaluated. Mini-tablets achieved acceptable weight variability, tensile strength, friability, and disintegration time at a reasonable solid fraction for each formulation. The content uniformity was acceptable for mini-tablets of 6.7% formulations with ≤170μm drug substance, mini-tablets of all 26.7% formulations, and composite dosage units containing five or more mini-tablets of any formulation. Results supported the manufacturing feasibility of quality mini-tablets, and their applicability as a flexible drug delivery tool. Copyright © 2017 Elsevier B.V. All rights reserved.

Evaluation of Tablets Divisibility in Pharmacoeconomic Aspects

Directory of Open Access Journals (Sweden)

Omer Yemsen

2013-10-01

Full Text Available Aim: Divisibility and dose homogeneity in scored tablets which form a part of the drugs those are in tablet forms in Turkey and have an extensive implementation area in drug therapy have a high importance for patient compliance and safety. In this study, it is aimed to evaluate Turkey%u2019s pharmaceutical market about cost differences of dividing scored tablets which has different unit quantities of the same active substance. Material and Method: In Turkey%u2019s pharmaceutical market, to detect cost differences of dividing scored tablets which has different unit quantities of the same active substance, All Drug%u2019s Price List that has been published on Turkish Medicine and Medical Devices Agency%u2019s web site is evaluated by using cost-minimization analysis method. Results: It is determined that the use of scored tablets make a price advantage of about 70%. Discussion: In conclusion, on package leaflets and outer packaging information those are prepared for the use of patients, the warning %u201CDon%u2019t divide, crack or swallow the tablets unless otherwise recommended by your doctor.%u201D should be stated and it is considered that it would be useful if the patient is informed about divisibility by the pharmacist.

Application of Neem Gum for Aqueous Film Coating of Ciprofloxacin Tablets

OpenAIRE

A P Kulkarni; Y R Shaikh; MH GR Dehghan

2013-01-01

Summary. At present the pharmaceutical industry and academia are focusing on the use of natural materials and resources for development of pharmaceutical product. In previous study, neem gum (NG), obtained from Azadirachata indica plant revealed satisfactory film forming ability. The present study evaluates the application potential of neem gum, as an aqueous film coating material, using ciprofloxacin hydrchloride (drug) as a model drug. Initial study of physical mixture indicated absence of ...

Eudragit-coated dextran microspheres of 5-fluorouracil for site-specific delivery to colon.

Science.gov (United States)

Rai, Gopal; Yadav, Awesh K; Jain, Narendra K; Agrawal, Govind P

2016-01-01

Objective of the present investigation was to prepare and evaluate the potential of enteric coated dextran microspheres for colon targeting of 5-fluorouracil (5-FU). Dextran microspheres were prepared by emulsification-crosslinking method and the formulation variables studied included different molecular weights of dextran, drug:polymer ratio, volume of crosslinking agent, stirring speed and time. Enteric coating (Eudragit S-100) of dextran microspheres was performed by oil-in-oil solvent evaporation method using different coat:core ratios (4:1 or 8:1). Uncoated and coated dextran microspheres were characterized by particle size, surface morphology, entrapment efficiency, DSC, in vitro drug release in the presence of dextranase and 2% rat cecal contents. The release study of 5-FU from coated dextran microspheres was pH dependent. No release was observed at acidic pH; however, the drug was released quickly where Eudragit starts solublizing there was continuous release of drug from the microspheres. Organ distribution study was suggested that coated dextran microspheres retard the release of drug in gastric and intestinal pH environment and released of drug from microspheres in colon due to the degradation of dextran by colonic enzymes.

Android Tablet Application Development For Dummies

CERN Document Server

Felker, Donn

2011-01-01

Get up to speed on the hottest opportunity in the application development arena App development for tablets is a booming business. Android tablets, including the popular Motorola Xoom, are gaining market share at breakneck speed, and this book can have even novice programmers creating great Android apps specifically for tablets quickly and easily. A little Java knowledge is helpful but not essential to get started creating apps. Android expert Donn Felker helps you get the Android environment up and running, use XML to create application menus, create an icon for your app, and submit your app

Galileo's Telescopy and Jupiter's Tablet

Science.gov (United States)

Usher, P. D.

2003-12-01

A previous paper (BAAS 33:4, 1363, 2001) reported on the dramatic scene in Shakespeare's Cymbeline that features the descent of the deity Jupiter. The paper suggested that the four ghosts circling the sleeping Posthumus denote the four Galilean moons of Jupiter. The god Jupiter commands the ghosts to lay a tablet upon the prone Posthumus, but says that its value should not be overestimated. When Posthumus wakens he notices the tablet, which he calls a "book." Not only has the deity's "tablet" become the earthling's "book," but it appears that the book has covers which Posthumus evidently recognizes because without even opening the book he ascribes two further properties to it: rarity, and the very property that Jupiter had earlier attributed, viz. that one must not read too much into it. The mystery deepens when the Jovian gift undergoes a second metamorphosis, to "label." With the help of the OED, the potentially disparate terms "tablet," "book," and "label," may be explained by terms appropriate either to supernatural or worldly beings. "Tablet" may recognize the Mosaic artifact, whereas "book" and "label" are probably mundane references to Galileo's Sidereus Nuncius which appeared shortly before Cymbeline. The message of the Olympian god indicates therefore that the book is unique even as its contents have limited value. The first property celebrates the fact that Galileo's book is the first of its kind, and the second advises that all results except the discovery of Jupiter's moons have been reported earlier, in Hamlet.

Observation of portal circulation through superior mesenteric vein by enteric coated capsule of thallium-201

Energy Technology Data Exchange (ETDEWEB)

Tonami, Norihisa; Nakajima, Kenichi; Watanabe, Naoto; Seto, Mikito; Yokoyama, Kunihiko; Shuke, Noriyuki; Michigishi, Takatoshi; Takayama, Teruhiko; Aburano, Tamio; Hisada, Kinichi

1988-06-01

A new method of oral administration of an enteric coated capsule of /sup 201/Tl (/sup 201/Tl-capsule) was developed to evaluate the portal circulation through the superior mesenteric vein (SMV). The /sup 201/Tl-capsule was not collapsed in the artificial gastric juice, whereas it melted soon after soaking in the artificial intestinal juice. In a clinical trial of 42 cases, /sup 201/Tl was satisfactory released in the duodenum in 36 cases where clear liver images were observed except in 1 patient. Heart to liver ratio (HL) at 60 or 90 min after duodenal release of /sup 201/Tl was 0.32+-0.07 (mean +-1 s.d.) in normal controls, 0.34+-0.12 in chronic hepatitis, 0.31+-0.12 in acute hepatitis, 0.45+-0.13 in liver cirrhosis and 0.48+-0.32 in cirrhosis with hepatocellular carcinoma. In 11 patients who had both oral and rectal studies with /sup 201/Tl, 7 showed a high HL ratio of more than 0.8 in the rectal study but only 1 showed a similarly high ratio of 1.07 in the oral study. In the group of varied liver disorders we have studied so far, it was found that most of the SMV blood flowed into the liver and the degree of portal systemic shunting (PSS) from the SMV was much smaller compared to that from the inferior mesenteric vein. The present study with oral administration of the /sup 201/Tl-capsule was of value in understanding portal circulation through the SMV, however, this technique seemed of limited usefulness for evaluating overall pathologic PSS.

Observation of portal circulation through superior mesenteric vein by enteric coated capsule of thallium-201

International Nuclear Information System (INIS)

Tonami, Norihisa; Nakajima, Kenichi; Watanabe, Naoto; Seto, Mikito; Yokoyama, Kunihiko; Shuke, Noriyuki; Michigishi, Takatoshi; Takayama, Teruhiko; Aburano, Tamio; Hisada, Kinichi; Tanaka, Nobuyoshi; Kobayashi, Kenichi

1988-01-01

A new method of oral administration of an enteric coated capsule of 201 Tl ( 201 Tl-capsule) was developed to evaluate the portal circulation through the superior mesenteric vein (SMV). The 201 Tl-capsule was not collapsed in the artificial gastric juice, whereas it melted soon after soaking in the artificial intestinal juice. In a clinical trial of 42 cases, 201 Tl was satisfactory released in the duodenum in 36 cases where clear liver images were observed except in 1 patient. Heart to liver ratio (H/L) at 60 or 90 min after duodenal release of 201 Tl was 0.32±0.07 (mean ±1 s.d.) in normal controls, 0.34±0.12 in chronic hepatitis, 0.31±0.12 in acute hepatitis, 0.45±0.13 in liver cirrhosis and 0.48±0.32 in cirrhosis with hepatocellular carcinoma. In 11 patients who had both oral and rectal studies with 201 Tl, 7 showed a high H/L ratio of more than 0.8 in the rectal study but only 1 showed a similarly high ratio of 1.07 in the oral study. In the group of varied liver disorders we have studied so far, it was found that most of the SMV blood flowed into the liver and the degree of portal systemic shunting (PSS) from the SMV was much smaller compared to that from the inferior mesenteric vein. The present study with oral administration of the 201 Tl-capsule was of value in understanding portal circulation through the SMV, however, this technique seemed of limited usefulness for evaluating overall pathologic PSS. (orig.)

Does the performance of wet granulation and tablet hardness affect the drug dissolution profile of carvedilol in matrix tablets?

Science.gov (United States)

Košir, Darjan; Ojsteršek, Tadej; Vrečer, Franc

2018-06-14

Wet granulation is mostly used process for manufacturing matrix tablets. Compared to the direct compression method, it allows for a better flow and compressibility properties of compression mixtures. Granulation, including process parameters and tableting, can influence critical quality attributes (CQAs) of hydrophilic matrix tablets. One of the most important CQAs is the drug release profile. We studied the influence of granulation process parameters (type of nozzle and water quantity used as granulation liquid) and tablet hardness on the drug release profile. Matrix tablets contained HPMC K4M hydrophilic matrix former and carvedilol as a model drug. The influence of selected HPMC characteristics on the drug release profile was also evaluated using two additional HPMC batches. For statistical evaluation, partial least square (PLS) models were generated for each time point of the drug release profile using the same number of latent factors. In this way, it was possible to evaluate how the importance of factors influencing drug dissolution changes in dependence on time throughout the drug release profile. The results of statistical evaluation show that the granulation process parameters (granulation liquid quantity and type of nozzle) and tablet hardness significantly influence the release profile. On the other hand, the influence of HPMC characteristics is negligible in comparison to the other factors studied. Using a higher granulation liquid quantity and the standard nozzle type results in larger granules with a higher density and lower porosity, which leads to a slower drug release profile. Lower tablet hardness also slows down the release profile.

[The effects of various factors on the in vitro velocity of drug release from repository tablets. Part 4: Isoniazid (Rimicid) respository tablets (author's transl)].

Science.gov (United States)

Tomassini, L; Michailova, D; Naplatanova, D; Slavtschev, P

1979-12-01

The authors investigated the release of isoniazid from repository tablets as related to form, processing technology, strength constant and storage for 5 years. On determining the diffusion coefficient (D), the initial dissolution rate (Vo) and the time required for the diffusion of the releasing medium to the middle of the tablet (t1/2), it was found that the difference in release rate between the flat and the biconvex tablets is small. Furthermore, it was stated that the three-layer tablets have very high D and Vo values and very low t1/2 values, for what reason they are unsuited for repository tablets of the composition under investigation. Moreover, it was found that an increase of the strength constant does not affect the D, t1/2 and Vo values, and that the release of isoniazid is retarded only in flat tablets with the highest strength constant. Storage exerts no effect on the drug release from these tablets. The industrial production of these tablets is under way.

To Study Capping or Lamination Tendency of Tablets Through Evaluation of Powder Rheological Properties and Tablet Mechanical Properties of Directly Compressible Blends.

Science.gov (United States)

Dudhat, Siddhi M; Kettler, Charles N; Dave, Rutesh H

2017-05-01

Air entrapment efficiency of the powders is one of the main factors leading to occurrence of capping or lamination tendency of tablets manufactured from the directly compressible powder blends. The purpose of the current research was to study this underlying cause leading to occurrence of capping or lamination of tablets through evaluation of powder rheological properties. Powder blends were prepared by addition of 0% w/w to 100% w/w of individual active pharmaceutical ingredient (API) [two model API: acetaminophen (APAP) and ibuprofen (IBU)] with microcrystalline cellulose without and with 0.5% w/w Magnesium Stearate as lubricant. Powder rheological properties were analyzed using FT4 Powder Rheometer for dynamic, bulk, and shear properties. Tablet mechanical properties of the respective blends were studied by determining the ability of the material to form tablet of specific strength under applied compaction pressure through tabletability profile. The results showed that powder rheometer distinguished the powder blends based on their ability to relieve entrapped air along with the distinctive flow characteristics. Powder blend prepared with increasing addition of APAP displayed low powder permeability as compared to IBU blends with better powder permeability, compressibility and flow characteristics. Also, lubrication of the APAP blends did not ease their ability to relieve air. Tabletability profiles revealed the potential occurrence of capping or lamination in tablets prepared from the powder blends with high APAP content. This study can help scientist to understand tableting performance at the early-developmental stages and can avoid occurrence capping and lamination of tablets.

Carbon Break Even Analysis: Environmental Impact of Tablets in Higher Education

OpenAIRE

Fadi Safieddine; Imad Nakhoul

2016-01-01

With the growing pace of tablets use and the large focus it is attracting especially in higher education, this paper looks at an important aspect of tablets; their carbon footprint. Studies have suggested that tablets have positive impact on the environment; especially since tablets use less energy than laptops or desktops. Recent manufacturers’ reports on the carbon footprint of tablets have revealed that a significant portion, as much as 80%, of the carbon footprint of tablets comes from pr...

Giving Iron Tablets by Health Worker and Pregnant Compliance in Consuming More Than 90 Tablets, in The Slum Urban, in The West Java Province and Yogyakarta

Directory of Open Access Journals (Sweden)

Tumaji Tumaji

2015-03-01

Full Text Available ABSTRAKLatar Belakang: Angka kematian ibu di Indonesia saat ini masih cukup tinggi dan sangat bervariasi di tingkat provinsi. Provinsi Jawa Barat (Jabar merupakan penyumbang kematian ibu terbesar yaitu 19,8%, sedangkan yang relatif kecil adalah Provinsi Daerah Istimewa Yogyakarta (DIY yaitu 1,1%. Mencegah anemia pada ibu hamil dengan minum tablet besi ≥ 90 selama hamil diharapkan mampu menekan kematian ibu akibat perdarahan. Tujuan: Membandingkan pemberian tablet zat besi oleh tenaga kesehatan dan kepatuhan ibu hamil mengonsumsinya, di daerah kumuh perkotaan di Provinsi Jabar dan DIY. Metode: Penelitian ini merupakan analisis lanjut objek dengan sampel dari data hasil Riskesdas 2010. Hasil: Berdasarkan karakteristik, sebagian besar ibu di Provinsi DIY berpendidikan tingkat menengah, bekerja sebagai wiraswasta/tani/nelayan/buruh. Sedangkan di Provinsi Jabar, sebagian besar hanya berpendidikan rendah dan tidak memiliki pekerjaan. Jumlah kepemilikan asuransi kesehatan di Provinsi DIY relatif lebih banyak dibanding di Provinsi jabar. Berdasarkan cakupan pemberian tablet zat besi, tampak bahwa sebagian besar ibu di Provinsi Jabar maupun DIY mendapatkan tablet zat besi selama kehamilannya (84,7% vs 96,0%. Kondisi ini jauh berbeda ketika dilihat dari persentase ibu hamil yang mengonsumsi tablet zat besi minimal 90 tablet. Terlihat bahwa ibu hamil yang mengonsumsi tablet zat besi ≥ 90 di Provinsi Jabar hanya 12,6% saja. Sebaliknya di Provinsi DIY, konsumsi tablet zat besi ≥ 90 persentasenya cukup tinggi yaitu mencapai 60,0%. Kesimpulan: Cakupan pemberian tablet zat besi di kedua provinsi relatif cukup baik, namun konsumsi tablet zat besi ≥ 90 tablet di Provinsi DIY relatif lebih baik dibanding di Provinsi di Jabar. Saran: disarankan pemerintah Provinsi Jabar melakukan promosi dan penyuluhan yang lebih gencar melalui berbagai media serta melakukan terobosan, misalnya dengan menunjuk orang terdekat dari si ibu hamil untuk menjadi pengawas dan

Compounded Apixaban Suspensions for Enteral Feeding Tubes.

Science.gov (United States)

Caraballo, Maria L; Donmez, Seda; Nathan, Kobi; Zhao, Fang

2017-07-01

Objective: There is limited information on compounded apixaban formulations for administration via enteral feeding tubes. This study was designed to identify a suitable apixaban suspension formulation that is easy to prepare in a pharmacy setting, is compatible with commonly used feeding tubes, and has a beyond-use date of 7 days. Methods: Apixaban suspensions were prepared from commercially available 5-mg Eliquis tablets. Several vehicles and compounding methods were screened for ease of preparation, dosage accuracy, and tube compatibility. Two tubing types, polyurethane and polyvinyl chloride, with varying lengths and diameters, were included in the study. They were mounted on a peg board during evaluation to mimic the patient body position. A 7-day stability study of the selected formulation was also conducted. Results: Vehicles containing 40% to 60% Ora-Plus in water all exhibited satisfactory flowability through the tubes. The mortar/pestle compounding method was found to produce more accurate and consistent apixaban suspensions than the pill crusher or crushing syringe method. The selected formulation, 0.25 mg/mL apixaban in 50:50 Ora-Plus:water, was compatible with both tubing types, retaining >98% drug in posttube samples. The stability study also confirmed that this formulation was stable physically and chemically over 7 days of storage at room temperature. Conclusions: A suitable apixaban suspension formulation was identified for administration via enteral feeding tubes. The formulation consisted of 0.25 mg/mL apixaban in 50:50 Ora-Plus:water. The stability study results supported a beyond-use date of 7 days at room temperature.

Teach yourself visually Windows 8 tablets

CERN Document Server

McFedries, Paul

2012-01-01

A visual guide to all the features of the new Windows 8 Tablet This must-have resource features visually rich, step-by-step instructions that show you how to get the most enjoyment from your Windows 8 tablet. Learn about the exciting new Metro UI, optimized specifically for touch devices. The most popular and commonly used apps and functions are covered too, along with the basics of syncing with a network, setting up e-mail, watching videos, listening to music, and common productivity tasks. This book provides all the guidance needed to enjoy all the best the new Windows 8 tablets have to offe

Understanding the Delamination Risk of a Trilayer Tablet Using Minipiloting Tools.

Science.gov (United States)

Tao, Jing; Robertson-Lavalle, Sophia; Pandey, Preetanshu; Badawy, Sherif

2017-11-01

A multilayer tablet is one of the formulation options used to mitigate chemical and physical incompatibility between different drug substances. Feasibility studies of multilayer tablets are often conducted using round flat-faced punch tooling. However, the link between different tooling designs and multilayer tablet performance is not well established. This study uses a prototype trilayer tablet and examines tooling design considerations when conducting small-scale studies to gauge the risk of interfacial defects. The impact of tablet weight and dimensions was evaluated to gain understanding of the effect of scale-up/down of tablet size. The factors in tooling selection, including tablet shape, cup depth, and size of embossing were evaluated to gain insight on the impact of tooling design on the interfacial strength of the trilayer tablet. It was found that tablet weight and dimensions can significantly affect the interfacial strength due to their impact on force transmission during compression and the retardation force from the die wall during ejection. Round flat-faced tooling generated trilayer tablets of the strongest interfacial strength compared to typical commercial tablets-oval shaped with concave surfaces. These factors should be accounted for when using round flat compacts to assess the interface risks of a multilayer tablet. Copyright © 2017 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Værsgo' ta' en tablet. Om brugen af tablets i dansk

DEFF Research Database (Denmark)

Lorentzen, Rasmus Fink

2014-01-01

Hvordan kan vi udvikle elevernes faglighed ved hjælp af it? Hvad er det i det hele taget vigtigt at lære i en tidssvarende folkeskole, så eleverne bliver klædt på til fremtidens samfund? Og kan iPads bruges til dette? Dette kapitel handler om fagdidaktik og tablets i undervisningen.......Hvordan kan vi udvikle elevernes faglighed ved hjælp af it? Hvad er det i det hele taget vigtigt at lære i en tidssvarende folkeskole, så eleverne bliver klædt på til fremtidens samfund? Og kan iPads bruges til dette? Dette kapitel handler om fagdidaktik og tablets i undervisningen....

Formulation and Evaluation of Ascorbic acid Tablets by Direct ...

African Journals Online (AJOL)

Formulation and Evaluation of Ascorbic acid Tablets by Direct Compression using Microcrystalline Starch as a Direct Compression Excipient. ... Abstract. PURPOSE: To evaluate the tableting properties of microcrystalline starch (MCS) used as a direct ... RESULTS: Mechanical properties of tablets formulated with MCS were

Bioavailability and stability of erythromycin delayed release tablets.

Science.gov (United States)

Ogwal, S; Xide, T U

2001-12-01

Erythromycin is available as the free base, ethylsuccinate, estolate, stearate, gluceptate, and lactobionate derivatives. When given orally erythromycin and its derivatives except the estolate are inactivated to some extent by the gastric acid and poor absorption may result. To establish whether delayed release erythromycin tablets meet the bioequivalent requirement for the market. Sectrophotometric analysis was used to determine the dissolution percentage of the tablets in vitro. High performance liquid chromatography and IBM/XT microcomputer was used to determine the bioavailability and pharmacokinetic parameters in vivo. Dissolution percentage in thirty minutes reached 28.9% and in sixty minutes erythromycin was completely released. The parameters of the delayed release tablets were Tlag 2.3 hr, Tmax.4.5 hr, and Cmax 2.123 g/ml Ka 0.38048 hr(-1) T (1/2) 1.8 hr, V*C/F 49.721 AUC 12.9155. The relative bioavailability of erythromycin delayed release tablet to erythromycin capsules was 105.31% The content, appearance, and dissolution bioavailability of delayed release erythromycin tablets conforms to the United States pharmacopoeia standards. The tablets should be stored in a cool and dry place in airtight containers and the shelf life is temporarily assigned two years.

21 CFR 520.1200 - Ivermectin, fenbendazole, and praziquantel tablets.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ivermectin, fenbendazole, and praziquantel tablets... Ivermectin, fenbendazole, and praziquantel tablets. (a) Specifications. Each chewable tablet contains either: (1) 68 micrograms (µg) ivermectin, 1.134 grams fenbendazole, and 57 milligrams (mg) praziquantel; or...

Comparative investigations of tablet crushing force testers

DEFF Research Database (Denmark)

Sonnergaard, Jørn; Jensen, C.G.; Poulsen, L.

2005-01-01

The performance of 16 tablet breaking force testers was evaluated in terms of accuracy, reproducibility and repeatability. Three tablet formulations with different plastic or brittle deformation mechanisms and with target breaking forces of 50, 100 and 150 N were tested. Statistically significant...... by the concept of components of variance was 5-7 % depending on the model tablet excipient. The standard deviation within testers (repeatability) was affected by the type of model formulation showing increasing variability with increasing brittleness of the compressed material. No specific effect of altering...

Development and Evaluation of Mucoadhesive Chlorhexidine Tablet ...

African Journals Online (AJOL)

Purpose: To formulate mucoadhesive chlorhexidine tablets and evaluate their drug release characteristics and mechanism. Methods: Chlorhexidine buccal adhesive tablets were prepared by direct compression using a blend of hydroxypropyl methylcellulose (HPMC) and chitosan as the bioadhesive polymers.

Novel platens to measure the hardness of a pentagonal shaped tablet.

Science.gov (United States)

Malladi, Jaya; Sidik, Kurex; Wu, Sutan; McCann, Ryan; Dougherty, Jeffrey; Parab, Prakash; Carragher, Thomas

2017-03-01

Tablet hardness, a measure of the breaking force of a tablet, is based on numerous factors. These include the shape of the tablet and the mode of the application of force. For instance, when a pentagonal-shaped tablet was tested with a traditional hardness tester with flat platens, there was a large variation in hardness measurements. This was due to the propensity of vertices of the tablet to crush, referred to as an "improper break". This article describes a novel approach to measure the hardness of pentagonal-shaped tablets using modified platens. The modified platens have more uniform loading than flat platens. This is because they reduce loading on the vertex of the pentagon and apply forces on tablet edges to generate reproducible tablet fracture. The robustness of modified platens was assessed using a series of studies, which included feasibility and Gauge Repeatability & Reproducibility (R&R) studies. A key finding was that improper breaks, generated frequently with a traditional hardness tester using flat platens, were eliminated. The Gauge R&R study revealed that the tablets tested with novel platens generated consistent values in hardness measurements, independent of batch, hardness level, and day of testing, operator and tablet dosage strength.

Application of face centred central composite design to optimise compression force and tablet diameter for the formulation of mechanically strong and fast disintegrating orodispersible tablets.

Science.gov (United States)

Pabari, Ritesh M; Ramtoola, Zebunnissa

2012-07-01

A two factor, three level (3(2)) face centred, central composite design (CCD) was applied to investigate the main and interaction effects of tablet diameter and compression force (CF) on hardness, disintegration time (DT) and porosity of mannitol based orodispersible tablets (ODTs). Tablet diameters of 10, 13 and 15 mm, and CF of 10, 15 and 20 kN were studied. Results of multiple linear regression analysis show that both the tablet diameter and CF influence tablet characteristics. A negative value of regression coefficient for tablet diameter showed an inverse relationship with hardness and DT. A positive value of regression coefficient for CF indicated an increase in hardness and DT with increasing CF as a result of the decrease in tablet porosity. Interestingly, at the larger tablet diameter of 15 mm, while hardness increased and porosity decreased with an increase in CF, the DT was resistant to change. The optimised combination was a tablet of 15 mm diameter compressed at 15 kN showing a rapid DT of 37.7s and high hardness of 71.4N. Using these parameters, ODTs containing ibuprofen showed no significant change in DT (ANOVA; p>0.05) irrespective of the hydrophobicity of the ibuprofen. Copyright © 2012 Elsevier B.V. All rights reserved.

Formulation and Evaluation of Ascorbic acid Tablets by Direct ...

African Journals Online (AJOL)

PURPOSE: To evaluate the tableting properties of microcrystalline starch (MCS) used as a direct compression excipient in the formulation of ascorbic acid tablets and to compare with the properties of tablets produced using microcrystalline cellulose (MCC). METHODS: MCS was obtained by partial hydrolysis of cassava ( ...

21 CFR 520.1660c - Oxytetracycline hydrochloride tablets/boluses.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Oxytetracycline hydrochloride tablets/boluses. 520....1660c Oxytetracycline hydrochloride tablets/boluses. (a) Specifications. Each tablet or bolus contains 250, 500, or 1,000 milligrams of oxytetracycline hydrochloride. (b) Sponsors. For sponsors in § 510...

21 CFR 520.1510 - Nitenpyram tablets.

Science.gov (United States)

2010-04-01

... and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... order of a licensed veterinarian. (d) Conditions of use—(1) Dogs—(i) Amount—(A) One 11.4-mg tablet for dogs weighing less than 25 pounds (lb) or one 57-mg tablet for dogs weighing more than 25 lb, as needed...

Astronomical Content in Rongorongo Tablet Keiti

DEFF Research Database (Denmark)

Wieczorek, Rafal

2011-01-01

Th e fi eld of rongorongo research: the study of Easter Island’s native script is in a peculiar state at the moment. While relative progress has been made in structural and statistical analysis in the last decades, at the level of both single glyphs as well as entire texts, little to no advanceme...... has been achieved in the actual decipherment. To shed new light on rongorongo research, a hypothesis regarding the contents of tablet Keiti, one of the 25 obtained artifacts, is proposed. Th e content, as well as the meaning, of all but one of these 25 rongorongo texts is still unknown....... In this publication, an interpretation for the recto side of tablet Keiti is presented. It is argued that the tablet contains astronomical observations or instructions regarding the Rapa Nui lunar calendar, and is similar in content to the only other rongorongo text whose function has been partially ascertained......: tablet Mamari. If the calendrical contents of this artifact were confi rmed, this would be a major boost to our understanding of Oceania’s only native script....

Polyols as filler-binders for disintegrating tablets prepared by direct compaction

NARCIS (Netherlands)

Bolhuis, Gerad K.; Rexwinkel, Erik G.; Zuurman, Klaas

Background: Although polyols are frequently used as tablet excipients in lozenges, chewing tablets, and orodisperse tablets, special directly compressible (DC) forms are recommended as filler-binder in common disintegrating tablets. Aim: In this article, DC types of isomalt, lactitol, mannitol,

Tablets, læring og nye forretningsmodeller

DEFF Research Database (Denmark)

Andersen, Pernille Viktoria Kathja

2011-01-01

D. 6 oktober satte Netværk om E-Læring (NoEL) i samarbejde med InVIO fokus på Tablet-computing igennem et heldagsarrangement i Aalborg Universitets nye omgivelser på Nyhavnsgade 14. Formålet med dagen var, at stille skarpt på tablet formatet og udforske potentialerne og udfordringerne med særligt...... vægt på iPads til mobillæring og nye forretningsmodeller. Tablet –computing er de seneste år blevet mere og mere udbredt indenfor både uddannelse, arbejdsliv og i fritiden. Ønsket for dagen var derfor at bidrage med diskussion og videndeling omkring, hvad den nye håndholdte touch teknologi kommer til...... at betyde for læring, samarbejde og forretningsmodeller og dermed hvilke nye vilkår tablet computing kan bidrage med indenfor arbejdsliv og uddannelse....

Cyclodextrins as excipients in tablet formulations.

Science.gov (United States)

Conceição, Jaime; Adeoye, Oluwatomide; Cabral-Marques, Helena Maria; Lobo, José Manuel Sousa

2018-04-22

This paper aims to provide a critical review of cyclodextrins as excipients in tablet formulations, highlighting: (i) the principal pharmaceutical applications of cyclodextrins; (ii) the most relevant technological aspects in pharmaceutical formulation development; and (iii) the actual regulatory status of cyclodextrins. Moreover, several illustrative examples are presented. Cyclodextrins can be used as complexing excipients in tablet formulations for low-dose drugs. By contrast, for medium-dose drugs and/or when the complexation efficiency is low, the methods to enhance the complexation efficiency play a key part in reducing the cyclodextrin quantity. In addition, these compounds are used as fillers, disintegrants, binders and multifunctional direct compression excipients of the tablets. Copyright © 2018 Elsevier Ltd. All rights reserved.

Damage-tolerance strategies for nacre tablets.

Science.gov (United States)

Wang, Shengnan; Zhu, Xinqiao; Li, Qiyang; Wang, Rizhi; Wang, Xiaoxiang

2016-05-01

Nacre, a natural armor, exhibits prominent penetration resistance against predatory attacks. Unraveling its hierarchical toughening mechanisms and damage-tolerance design strategies may provide significant inspiration for the pursuit of high-performance artificial armors. In this work, relationships between the structure and mechanical performance of nacre were investigated. The results show that other than their brick-and-mortar structure, individual nacre tablets significantly contribute to the damage localization of nacre. Affected by intracrystalline organics, the tablets exhibit a unique fracture behavior. The synergistic action of the nanoscale deformation mechanisms increases the energy dissipation efficiency of the tablets and contributes to the preservation of the structural and functional integrity of the shell. Copyright © 2016 Elsevier Inc. All rights reserved.

Development of Corn Starch-Neusilin UFL2 Conjugate as Tablet Superdisintegrant: Formulation and Evaluation of Fast Disintegrating Tablets

Directory of Open Access Journals (Sweden)

Prateek Juneja

2014-01-01

Full Text Available In the present study, corn Starch-Neusilin UFL2 conjugates were prepared by physical, chemical, and microwave methods with the aim of using the conjugates as tablet superdisintegrant. Various powder tests, namely, angle of repose, bulk density, tapped density, Hausner’s ratio, Carr’s index, swelling index, and powder porosity were conducted on the samples. The conjugates were characterized by ATR-FTIR, XRD, DSC, and SEM techniques. Heckel and Kawakita models were applied to carry out compression studies for the prepared conjugates. Fast disintegrating tablets of domperidone were prepared using corn starch and corn Starch-Neusilin UFL2 conjugates as tablet superdisintegrants in different concentrations. Conjugates were found to possess good powder flow and tabletting properties. Heckel analysis indicated that the conjugates prepared by microwave method showed the slowest onset of plastic deformation while Kawakita analysis indicated that the conjugates prepared by microwave method exhibited the highest amount of total plastic deformation. The study revealed that the corn Starch-Neusilin UFL2 conjugates possess improved powder flow properties and could be a promising superdisintegrant for preparing fast disintegrating tablet. Also, the results sugessted that the microwave method was found to be most effective for the preparation of corn Starch-Neusilin UFL2 conjugates.

Development of fast disintegrating compressed tablets using amino acid as disintegration accelerator: evaluation of wetting and disintegration of tablet on the basis of surface free energy.

Science.gov (United States)

Fukami, Jinichi; Ozawa, Asuka; Yoshihashi, Yasuo; Yonemochi, Etsuo; Terada, Katsuhide

2005-12-01

A fast disintegrating compressed tablet was formulated using amino acids, such as L-lysine HCl, L-alanine, glycine and L-tyrosine as disintegration accelerator. The tablets having the hardness of about 4 kgf were prepared and the effect of amino acids on the wetting time and disintegration time in the oral cavity of tablets was examined on the basis of surface free energy of amino acids. The wetting time of the tablets increased in the order of L-lysine HCl, L-alanine, glycine and L-tyrosine, whereas the disintegration time in the oral cavity of the tablets increased in the order of L-alanine, glycine, L-lysine HCl and L-tyrosine. These behaviors were well analyzed by the introduction of surface free energy. When the polar component of amino acid was large value or the dispersion component was small value, faster wetting of tablet was observed. When the dispersion component of amino acid was large value or the dispersion component was small value, faster disintegration of tablet was observed, expect of L-tyrosine tablet. The fast disintegration of tablets was explained by the theory presented by Matsumaru.

Embolic stroke associated with injection of buprenorphine tablets.

Science.gov (United States)

Lim, C C Tchoyoson; Lee, Sze Haur; Wong, Yee-Choon; Hui, Francis

2009-09-15

Drug users who crush, dissolve, and inject buprenorphine tablets parenterally may be at risk of severe thromboembolic complications or death. We describe patients with neurologic complications after injecting buprenorphine tablets. Brain MRI including diffusion-weighted imaging (DWI) in patients admitted to the neurologic department after injecting buprenorphine tablets were reviewed. Seven men had neurologic complications after buprenorphine tablet injection. In 5 patients, multiple small scattered hyperintense lesions were detected on DWI in the cortex, white matter, and basal ganglia of the cerebral hemisphere; one patient had a single small lesion. The side of MRI abnormality corresponded to the side of needle marks on the neck except in one patient who had bilateral injections. One patient, who denied injecting into the neck, had DWI abnormalities in the middle cerebral artery territory on one side and occlusion of the ipsilateral internal carotid artery. Buprenorphine tablets can be intentionally or inadvertently injected into the carotid artery, causing a characteristic appearance on diffusion-weighted imaging, consistent with embolic cerebral infarction.

Tensile and shear methods for measuring strength of bilayer tablets.

Science.gov (United States)

Chang, Shao-Yu; Li, Jian-Xin; Sun, Changquan Calvin

2017-05-15

Both shear and tensile measurement methods have been used to quantify interfacial bonding strength of bilayer tablets. The shear method is more convenient to perform, but reproducible strength data requires careful control of the placement of tablet and contact point for shear force application. Moreover, data obtained from the shear method depend on the orientation of the bilayer tablet. Although more time-consuming to perform, the tensile method yields data that are straightforward to interpret. Thus, the tensile method is preferred in fundamental bilayer tableting research to minimize ambiguity in data interpretation. Using both shear and tensile methods, we measured the mechanical strength of bilayer tablets made of several different layer combinations of lactose and microcrystalline cellulose. We observed a good correlation between strength obtained by the tensile method and carefully conducted shear method. This suggests that the shear method may be used for routine quality test of bilayer tablets during manufacturing because of its speed and convenience, provided a protocol for careful control of the placement of the tablet interface, tablet orientation, and blade is implemented. Copyright © 2017 Elsevier B.V. All rights reserved.

Profil Disolusi Terbanding Tablet Rifampisin Merek Dan Generik

OpenAIRE

Nurtanti, Mutiara Poetri; Kusuma, Anjar Mahardian; Siswanto, Agus

2010-01-01

Obat generik saat ini masih dipandang sebelah mata oleh masyarakat karena alasan kualitas dari obat generik lebih rendah dibandingkan obat merek. Tujuan penelitian ini untuk mengetahui perbandingan profil disolusi rifampisin tablet merek (A, B, C) dengan tablet rifampisin generik (D, E). Parameter penting dalam menentukan mutu obat dalam bentuk tablet adalah penetapan kekerasan, penetapan waktu hancur dan uji disolusi. Pengambilan sampel dilakukan berdasarkan produk yang beredar di pasaran ya...

Ginger Orally Disintegrating Tablets to Improve Swallowing in Older People.

Science.gov (United States)

Hirata, Ayumu; Funato, Hiroki; Nakai, Megumi; Iizuka, Michiro; Abe, Noriaki; Yagi, Yusuke; Shiraishi, Hisashi; Jobu, Kohei; Yokota, Junko; Hirose, Kahori; Hyodo, Masamitsu; Miyamura, Mitsuhiko

2016-01-01

We previously prepared and pharmaceutically evaluated ginger orally disintegrating (OD) tablets, optimized the base formulation, and carried out a clinical trial in healthy adults in their 20 s and 50s to measure their effect on salivary substance P (SP) level and improved swallowing function. In this study, we conducted clinical trials using the ginger OD tablets in older people to clinically evaluate the improvements in swallowing function resulting from the functional components of the tablet. The ginger OD tablets were prepared by mixing the excipients with the same amount of mannitol and sucrose to a concentration of 1% ginger. Eighteen healthy older adult volunteers aged 63 to 90 were included in the swallowing function test. Saliva was collected before and 15 min after administration of the placebo and ginger OD tablets. Swallowing endoscopy was performed by an otolaryngologist before administration and 15 min after administration of the ginger OD tablets. A scoring method was used to evaluate the endoscopic swallowing. Fifteen minutes after taking the ginger OD tablets, the salivary SP amount was significantly higher than prior to ingestion or after taking the placebo (pginger OD tablets. Our findings showed that the ginger OD tablets increased the salivary SP amount and improved swallowing function in older people with appreciably reduced swallowing function.

Portable Tablets in Science Museum Learning: Options and Obstacles

Science.gov (United States)

Gronemann, Sigurd Trolle

2017-01-01

Despite the increasing use of portable tablets in learning, their impact has received little attention in research. In five different projects, this media-ethnographic and design-based analysis of the use of portable tablets as a learning resource in science museums investigates how young people's learning with portable tablets matches the…

21 CFR 520.1696d - Penicillin V potassium tablets.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Penicillin V potassium tablets. 520.1696d Section... Penicillin V potassium tablets. (a) Specifications. Each tablet contains penicillin V potassium equivalent to 125 milligrams (200,000 units) or 250 milligrams (400,000 units) of penicillin V. (b) Sponsors. See...

The tabletting properties of Stearolac-S | Onyechi | Journal of ...

African Journals Online (AJOL)

press was used to determine the unit ejection force of tablets made from the direct compression formulations. The effects of the excipients on tablet hardness, friability, disintegration and dissolution rate were also evaluated. Tablets containing 3 - 4 % w/w STEAROLAC-S gave unit ejection force values comparable to those ...

Characterization of the Roman curse tablet

Science.gov (United States)

Liu, Wen; Zhang, Boyang; Fu, Lin

2017-08-01

The Roman curse tablet, produced in ancient Rome period, is a metal plate that inscribed with curses. In this research, several techniques were used to find out the physical structure and chemical composition of the Roman curse tablet, and testified the hypothesis that whether the tablet is made of pure lead or lead alloy. A sample of Roman Curse Tablet from the Johns Hopkins Archaeological Museum was analyzed using several different characterization techniques to determine the physical structure and chemical composition. The characterization techniques used were including optical microscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), and differential scanning calorimetry (DSC). Because of the small sample size, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence (XRF) cannot test the sample. Results from optical microscopy and SEM, enlarged images of the sample surface were studied. The result revealed that the sample surface has a rough, non-uniform, and grainy surface. AFM provides three-dimensional topography of the sample surface, studying the sample surface in atomic level. DSC studies the thermal property, which is most likely a lead-alloy, not a pure lead. However, none of these tests indicated anything about the chemical composition. Future work will be required due to the lack of measures finding out its chemical composition. Therefore, from these characterization techniques above, the Roman curse tablet sample is consisted of lead alloy, not pure lead.

Placing wireless tablets in clinical settings for patient education.

Science.gov (United States)

Stribling, Judy C; Richardson, Joshua E

2016-04-01

The authors explored the feasibility and possible benefit of tablet-based educational materials for patients in clinic waiting areas. We distributed eight tablets preloaded with diagnosis-relevant information in two clinic waiting areas. Patients were surveyed about satisfaction, usability, and effects on learning. Technical issues were resolved. Thirty-seven of forty patients completed the survey. On average, the patients were satisfied in all categories. Placing tablet-based educational materials in clinic waiting areas is relatively easy to implement. Patients using tablets reported satisfaction across three domains: usability, education, and satisfaction.

Quality Enhancement by Inclusion Complex Formation of Simvastatin Tablets

Directory of Open Access Journals (Sweden)

Emőke Rédai

2013-08-01

Full Text Available Introduction: Simvastatin is an inhibitor of hydroxy-methyl-glutaryl-coenzyme A reductase, used in the treatment of hypercholesterolemia. To enhance its bioavailability by inclusion complexation, as host molecule randommethyl-β-cyclodextrin had been used. After evaluating the complexes we chose the kneading product in 1:2 molar ratio for incorporation of 10 mg simvastatin tablets. Materials and methods: We prepared homogenous mixtures of the inclusion complex and some excipients. The tablets were prepared by direct compression. The tablets were evaluated in regard to: weight uniformity, thickness, diameter, hardness, friability, disintegration and dissolution profile. Results: Weights are in the range of 196-208 mg, diameter 6.83-6.86 mm, height 3.86-4.01 mm, hardness 78.3-113.1 N, friability 0.75- 1.19 %, disintegration above 15 minutes. The dissolved amounts of simvastatin from the tablets are higher compared to the dissolution of pure simvastatin, but lower than the dissolution of the complex itself. Excipients, like disintegrants and lubricants greatly influence the dissolution properties of the tablets. Conclusions: According to our results, tablets containing inclusion complex of simvastatin exhibit better solubility, according to the dissolved amount of simvastatin, than pure drug alone. Proper physical parameters of the tablets are obtained by application of 5 % Primellose

Replacing Smartphones With Mini Tablet Technology: An Evaluation.

Science.gov (United States)

Maneval, Rhonda; Mechtel, Marci

Handheld technology allows students to access point-of-care resources throughout the clinical experience. To assess the viability of replacing student smartphones with tablets, an evaluation project was undertaken. Overall, students were equally dissatisfied with the 2 types of tablets that were evaluated. Students saw the potential usefulness of tablets to manage clinical assignments, interact with the learning management system, and communicate with faculty, but not for retrieving information currently accessible on their phones.

A fixed-dose combination tablet of gemigliptin and metformin sustained release has comparable pharmacodynamic, pharmacokinetic, and tolerability profiles to separate tablets in healthy subjects.

Science.gov (United States)

Park, Sang-In; Lee, Howard; Oh, Jaeseong; Lim, Kyoung Soo; Jang, In-Jin; Kim, Jeong-Ae; Jung, Jong Hyuk; Yu, Kyung-Sang

2015-01-01

In type 2 diabetes mellitus, fixed-dose combination (FDC) can provide the complementary benefits of correction of multiple pathophysiologic defects such as dysfunctions in glycemic or metabolic control while improving compliance compared with separate tablets taken together. The objective of the study reported here was to compare the pharmacodynamic (PD), pharmacokinetic (PK), and tolerability profiles of gemigliptin and extended-release metformin (metformin XR) between FDC and separate tablets. A randomized, open-label, single-dose, two-way, two-period, crossover study was conducted in 28 healthy male volunteers. Two FDC tablets of gemigliptin/metformin 25/500 mg or separate tablets of gemigliptin (50 mg ×1) and metformin XR (500 mg ×2) were orally administered in each period. Serial blood samples were collected up to 48 hours post-dose to determine dipeptidyl peptidase 4 (DPP-4) activity using spectrophotometric assay and concentrations of gemigliptin and metformin using tandem mass spectrometry. Geometric mean ratios (GMRs) of FDC to separate tablet formulations and their 90% confidence intervals (CIs) were calculated to compare the PD and PK parameters between the two formulations. Tolerability was assessed throughout the study. The plasma DPP-4 activity-time curves of the FDC and the separate tablets almost overlapped, leading to a GMR (90% CI) of the FDC to separate tablets for the plasma DPP-4 activity and its maximum inhibition of 1.00 (0.97-1.04) and 0.92 (0.82-1.05), respectively. Likewise, all of the GMRs (90% CIs) of FDC to separate tablets for the area under the plasma concentration-time curve and maximum plasma concentration of gemigliptin and metformin fell entirely within the conventional bioequivalence range of 0.80-1.25. Both the FDC and separate tablets were well tolerated. The PD, PK, and tolerability profiles of gemigliptin and metformin XR in FDC and separate tablets were found to be comparable. The FDC tablet of gemigliptin and metformin

Tablet Computer Literacy Levels of the Physical Education and Sports Department Students

Directory of Open Access Journals (Sweden)

Gulten HERGUNER

2016-04-01

Full Text Available Education systems are being affected in parallel by newly emerging hardware and new developments    occurring in technology daily. Tablet usage especially is becoming ubiquitous in the teaching‐learning processes in recent years. Therefore, using the tablets effectively, managing them and having a high level of tablet literacy play an important role within the education system. This study aimed at determining the tablet literacy levels of students in the Physical Education and Sports Teaching department at Sakarya University in Turkey, and examining this data with regard to various variables. Some 276 students participated in the study. Findings of the study suggest that the sample has a high tablet literacy level. While no significant difference was found in the tablet literacy  by gender, the students in the 2nd grade are noted to have higher levels of tablet literacy compared to the students in 3rd and 4th grades and tablet owners are more tablet literate when compared to non‐owners. A significant but low level correlation was found between the tablet usage time and tablet literacy.  

Optimization of fast dissolving etoricoxib tablets prepared by sublimation technique

OpenAIRE

Patel D; Patel M

2008-01-01

The purpose of this investigation was to develop fast dissolving tablets of etoricoxib. Granules containing etoricoxib, menthol, crospovidone, aspartame and mannitol were prepared by wet granulation technique. Menthol was sublimed from the granules by exposing the granules to vacuum. The porous granules were then compressed in to tablets. Alternatively, tablets were first prepared and later exposed to vacuum. The tablets were evaluated for percentage friability and disintegration time. A 3 2 ...

Transforming the Classroom With Tablet Technology.

Science.gov (United States)

Sargent, Lana; Miles, Elizabeth

Identifying the most effective models for integrating new technology into the classroom and understanding its effects on educational outcomes are essential for nurse educators. This article describes an educational intervention with tablet technology (iPads) using an innovative case-based learning model in a nursing program. Students reported positive learning outcomes when using the tablet technology for learning course content.

Enhanced oral bioavailability of felodipine by novel solid self-microemulsifying tablets.

Science.gov (United States)

Jing, Boyu; Wang, Zhiyuan; Yang, Rui; Zheng, Xia; Zhao, Jia; Tang, Si; He, Zhonggui

2016-01-01

The novel self-microemulsifying (SME) tablets were developed to enhance the oral bioavailability of a poor water-soluble drug felodipine (FDP). Firstly, FDP was dissolved in the optimized liquid self-microemusifying drug delivery systems (SMEDDS) containing Miglyol® 812, Cremophor® RH 40, Tween 80 and Transcutol® P, and the mixture was solidified with porous silicon dioxide and crospovidone as adsorbents. Then after combining the solidified powders with other excipients, the solid SME tablets were prepared by wet granulation-compression method. The prepared tablets possessed satisfactory characterization; the droplet size of the SME tablets following self-emulsification in water was nearly equivalent to the liquid SMEDDS (68.4 ± 14.0 and 64.4 ± 12.0 nm); differential scanning calorimetry (DSC) and powder X-ray diffractometry (PXRD) analysis demonstrated that FDP in SME tablets had undergone a polymorphism transition from a crystal form to an amorphous state, which was further confirmed by transmission electron microscopy (TEM). A similar dissolution performance of SME tablets and liquid SMEDDS was also obtained under the sink condition (85% within 10 min), both significantly higher than commercial tablets. The oral bioavailability was evaluated for the SME tablets, liquid SMEDDS and commercial conventional tablets in the fasted beagle dogs. The AUC of FDP from the SME tablets was about 2-fold greater than that of conventional tablets, but no significant difference was found when compared with the liquid SMEDDS. Accordingly, these preliminary results suggest that this formulation approach offers a useful large-scale producing method to prepare the solid SME tablets from the liquid SMEDDS for oral bioavailability equivalent enhancement of poorly soluble FDP.

Chewability testing in the development of a chewable tablet for hyperphosphatemia.

Science.gov (United States)

Lanz, Michael; Baldischweiler, Jan; Kriwet, Burkhard; Schill, Jutta; Stafford, John; Imanidis, Georgios

2014-12-01

The official Pharmacopeia does not include a test procedure for the in vitro estimation of the chewability of tablets and publications in the scientific literature on this subject are rare. The purpose of this study was to evaluate a number of different test procedures for assessing chewability, starting from standard breaking force and strength testing and progressing to develop new procedures that simulate the actual chewing action on tablets. A further goal was to apply these test procedures to characterize the chewability of the novel phosphate binder PA21 in comparison with a commercially available phosphate binder chewable tablet product based on lanthanum (Fosrenol®) and a chewable tablet product containing calcium (Calcimagon®) - the latter being used as a standard for its very good chewability. For this purpose, a number of development formulations (different batches of PA21) were tested. The radial or diametrical tablet breaking force offers a poor means of assessing chewability while the axial breaking force was concluded to better reflect the effect of chewing on the tablet. Measurement of tablet behavior upon repeated loading afforded the best simulation of the actual chewing action and was found to have a good discriminating power with respect to chewability of the tested tablets, especially when the tablet was moistened with artificial saliva. The developed tests are shown to be more suitable for evaluating chewing properties of tablets than currently used Pharmacopeial tests. Following ICHQ6, which calls for specification of hardness for chewable tablets, these test procedures enabled the optimal chewability features of PA21 tablets in development to be confirmed whilst still maintaining capabilities for robust production and transportation processes.

Fire behavior of e-tablets stored in aircraft galley carts.

Science.gov (United States)

2015-04-01

The use of electronic-tablets (e-tablets) as replacements for conventional in-flight entertainment systems has gained popularity : among airlines globally. Innovative methods of storing and charging e-tablets in galley carts have been suggested or ar...

Quality-by-design approach for the development of telmisartan potassium tablets.

Science.gov (United States)

Oh, Ga-Hui; Park, Jin-Hyun; Shin, Hye-Won; Kim, Joo-Eun; Park, Young-Joon

2018-05-01

A quality-by-design approach was adopted to develop telmisartan potassium (TP) tablets, which were bioequivalent with the commercially available Micardis ® (telmisartan free base) tablets. The dissolution pattern and impurity profile of TP tablets differed from those of Micardis ® tablets because telmisartan free base is poorly soluble in water. After identifying the quality target product profile and critical quality attributes (CQAs), drug dissolution, and impurities were predicted to be risky CQAs. To determine the exact range and cause of risks, we used the risk assessment (RA) tools, preliminary hazard analysis and failure mode and effect analysis to determine the parameters affecting drug dissolution, impurities, and formulation. The range of the design space was optimized using the face-centered central composite design among the design of experiment (DOE) methods. The binder, disintegrant, and kneading time in the wet granulation were identified as X values affecting Y values (disintegration, hardness, friability, dissolution, and impurities). After determining the design space with the desired Y values, the TP tablets were formulated and their dissolution pattern was compared with that of the reference tablet. The selected TP tablet formulated using design space showed a similar dissolution to that of Micardis ® tablets at pH 7.5. The QbD approach TP tablet was bioequivalent to Micardis ® tablets in beagle dogs.

RP-HPLC Determination of vitamins B1, B3, B6, folic acid and B12 in multivitamin tablets

Directory of Open Access Journals (Sweden)

SOTE VLADIMIROV

2005-10-01

Full Text Available Abstract:Asimple and sensitive reversed-phase, ion-pair HPLC method was developed and validated for the simultaneous determination of B-group vitamins, thiamine chloride hydrochloride (B1, nicotinamide (B3, pyridoxine hydrochloride (B6 and folic acid in Pentovit® coated tablets. The cyanocobalamine (B12 was determined separately, because of its low concentration in the investigated multivitamin preparation. RP-HPLC analysis was performed with a LKB 2150 HPLC system, equipped with a UV/VIS Waters M484 detector. The procedures for the determination of B1, B2, B6 and folic acid were carried out on a Supelcosil ABZ+ (15 cm 4.6 mm; 5 µm column with methanol-5mM heptanesulphonic acid sodium salt 0.1%triethylamine TEA(25:75 V/V; pH 2.8 as themobile phase. For the determination of B12 a Suplex pKb-100 (15 cm 4.6 mm; 5 µm column andmethanol–water (22:78 V/V as themobile phase were used. The column effluentsweremonitored at 290 nm for B 1, B3, B6 and folic acid, and at 550 nm for B12. The obtained results and statistical parameters for all the investigated vitamins of the B-group in Pentovit® coated tablets were satisfactory and ranged from 90.4 % to 108.5 % (RSD. from 0.5% to 4.1 %. The parameters for the validation of the methods are given.

Evaluation of powder and tableting properties of chitosan

OpenAIRE

Picker-Freyer, Katharina M.; Brink, Diana

2006-01-01

The aim of this study was to analyze the process of tablet formation and the properties of the resulting tablets for 3 N-deacetylated chitosans, with a degree of deacetylation of 80%, 85%, or 90%. Material properties, such as water content, particle size and morphology, glass transition temperature, and molecular weight were studied. The process of tablet formation was analyzed by 3-D modeling, Heckel analysis, the pressure time function, and energy calculations in combination with elastic re...

Study of the variables which influence the impregnation of globules, compressed tablets and tablet triturates used in homeopathy

Directory of Open Access Journals (Sweden)

Fernanda Santos de Souza

2012-09-01

Full Text Available Globules, compressed tablets and tablet triturates are solid dosage forms used in homeopathy. Divergences can be noted between the preparation techniques described in official compendiums as well as those applied in homeopathic pharmacies. The difficulty associated with standardization of the impregnation of these dosage forms occurs due to the lack of detail provided for the techniques in the literature, leaving it up to each pharmacy to decide on the exact method of preparation. The objective was to optimize the impregnation technique, through investigating the variables that influence the impregnation of globules, compressed tablets and tablet triturates, applying the statistical tool of factorial design. The independent variables were the dosage form, percentage and type of impregnation and drying temperature, and the dependent variables were the mass gain, disintegration time, friability and hardness. For the globules, the greatest mass gain was for 10% impregnation and drying at 20 ºC. For the tablet triturates and compressed tablets the greatest mass gain was for 15% impregnation and there was no difference between the results obtained using simple and triple impregnation or different drying temperatures. The results can contribute to improving the final product quality, besides aiding in the establishment of standardized techniques for the official compendiums.Glóbulos, comprimidos e tabletes são formas farmacêuticas sólidas utilizadas em homeopatia. Constatam-se divergências entre técnicas de preparação descritas nos compêndios oficiais, bem como em farmácias homeopáticas. A dificuldade de padronização na impregnação destas formas farmacêuticas também ocorre devido à falta de detalhamento das técnicas na literatura existente, deixando para cada farmácia a escolha de como executá-las. O objetivo foi otimizar a técnica de impregnação, através do estudo de variáveis que interferem na impregnação de gl

Carbamazepine solubility enhancement in tandem with swellable polymer osmotic pump tablet: A promising approach for extended delivery of poorly water-soluble drugs

Directory of Open Access Journals (Sweden)

Hadjira Rabti

2014-06-01

Full Text Available Elementary osmotic pump (EOP is a unique extended release (ER drug delivery system based on the principle of osmosis. It has the ability to minimize the amount of the drug, accumulation and fluctuation in drug level during chronic uses. Carbamazepine (CBZ, a poorly water-soluble antiepileptic drug, has serious side effects on overdoses and chronic uses. The aim of the present study was to design a new EOP tablet of CBZ containing a solubility enhancers and swellable polymer to reduce its side effects and enhance the patient compliance. Firstly, a combination of solubilizing carriers was selected to improve the dissolution of the slightly soluble drug. Then, designing the new EOP tablet and investigating the effect of different variables of core and coat formulations on drug release behavior by single parameter optimization and by Taguchi orthogonal design with analysis of variance (ANOVA, respectively. The results showed that CBZ solubility was successfully enhanced by a minimum amount of combined polyvinyl pyrrolidone (PVP K30 and sodium lauryl sulfate (SLS. The plasticizer amount and molecular weight (MW together with the osmotic agent amount directly affect the release rate whereas the swellable polymer amount and viscosity together with the semi-permeable membrane (SPM thickness inversely influence the release rate. In addition, the tendency of following zero order kinetics was mainly affected by the coat components rather than those of the core. Further, orifice size does not have any significant effect on the release behavior within the range of 0.1 mm to 0.8 mm. In this study we report the successful formulation of CBZ-EOP tablets, which were similar to the marketed product Tegretol CR 200 and able to satisfy the USP criterion limits and to deliver about 80% of CBZ at a rate of approximately zero order for up to 12 h.

Quantitative Determination of Metformin Hydrochloride in Tablet ...

African Journals Online (AJOL)

Purpose: To develop and validate a suitable method for the assay of metformin hydrochloride (HCl) in tablets containing croscarmellose sodium as an additive. Methods: Methanol and ethanol (99%) were assessed as solvents for sample preparation for the assay of metformin HCl in tablets containing croscarmellose ...

Placing wireless tablets in clinical settings for patient education

Directory of Open Access Journals (Sweden)

Judy C. Stribling, MA, MLS

2016-11-01

Full Text Available Objective: The authors explored the feasibility and possible benefit of tablet-based educational materials for patients in clinic waiting areas. Methods: We distributed eight tablets preloaded with diagnosis-relevant information in two clinic waiting areas. Patients were surveyed about satisfaction, usability, and effects on learning. Technical issues were resolved. Results: Thirty-seven of forty patients completed the survey. On average, the patients were satisfied in all categories. Conclusions: Placing tablet-based educational materials in clinic waiting areas is relatively easy to implement. Patients using tablets reported satisfaction across three domains: usability, education, and satisfaction.

[Effect of food thickener on disintegration and dissolution of magnesium oxide tablets].

Science.gov (United States)

Tomita, Takashi; Goto, Hidekazu; Yoshimura, Yuya; Tsubouchi, Yoshiko; Nakanishi, Rie; Kojima, Chikako; Yoneshima, Mihoko; Yoshida, Tadashi; Tanaka, Katsuya; Sumiya, Kenji; Kohda, Yukinao

2015-01-01

It has been reported that magnesium oxide tablets are excreted in a non-disintegrated state in the stool of patients when the tablets are administered after being immersed in a food thickener. Therefore we examined whether immersion in a food thickener affects the pharmacological effect in patients taking magnesium oxide tablets, and whether immersion affects its disintegration and solubility. The mean dosage (1705 mg/d) was higher for patients who took tablets after immersion in a food thickener than for those who took non-immersed tablets (1380 mg/d). The disintegration time and dissolution rate of the immersed tablets were lower than those of non-immersed tablets in vitro. Furthermore, components that constitute the food thickener and differences in composition concentrations differentially affect the disintegration and solubility of magnesium oxide tablets. This suggests that commercially available food thickeners are likely to be associated with changes in the degradation of magnesium oxide tablets, and they therefore should be carefully used in certain clinical situations.

Interaction With PC Tablets And Possible Emotional Responses

Directory of Open Access Journals (Sweden)

Emy Agren

2015-08-01

Full Text Available The remarkable developments in mobile-based technologies have brought prominent impacts on human life style. Today life is running on mobile electronic devices smart phones tablets gaming devices and video-players. Generally the users acquaint with the features and properties of products after emotionally and physically interacting with the devices. The interaction in return influencing our moods depending on the feelings the technology creates. The focus of this study lays on the uses of tablets or also called PC tablets and its effects on its users emotional responses. To discover possible emotional responses with the tablets the data in this work were collected through a survey questionnaire from participants belongs to various backgrounds age groups and genders. The model of emotions was adopted in order to classify the emotional responses.The study has found that during or after the interaction with the tablets the users may get positive or negative emotional responses of a different kind. The users mood can also be affected by awakening such emotional feelings as happiness sadness frustration etc.

Graphics tablet technology in second year thermal engineering teaching

Directory of Open Access Journals (Sweden)

Antonio Carrillo Andrés

2013-12-01

Full Text Available Graphics tablet technology is well known in markets such as manufacturing, graphics arts and design but they have not yet found widespread acceptance for university teaching. A graphics tablet is an affordable and efficient teaching tool that combines the best features from traditional and new media. It allows developing a progressive, interactive lecture (as a traditional blackboard does. However, the tablet is more versatile, being able to integrate graphic material such as tables, graphs, colours, etc. In addition to that, lecture notes can be saved and posted on a course website. The objective of this paper is to show the usefulness of tablet technology in undergraduate engineering teaching by sharing experiences made using a graphics tablet for lecturing a second year Thermal Engineering course. Students’ feedback is definitely positive, though there are some caveats regarding technical and operative problems.

Developing a mapping tool for tablets

Science.gov (United States)

Vaughan, Alan; Collins, Nathan; Krus, Mike

2014-05-01

Digital field mapping offers significant benefits when compared with traditional paper mapping techniques in that it provides closer integration with downstream geological modelling and analysis. It also provides the mapper with the ability to rapidly integrate new data with existing databases without the potential degradation caused by repeated manual transcription of numeric, graphical and meta-data. In order to achieve these benefits, a number of PC-based digital mapping tools are available which have been developed for specific communities, eg the BGS•SIGMA project, Midland Valley's FieldMove®, and a range of solutions based on ArcGIS® software, which can be combined with either traditional or digital orientation and data collection tools. However, with the now widespread availability of inexpensive tablets and smart phones, a user led demand for a fully integrated tablet mapping tool has arisen. This poster describes the development of a tablet-based mapping environment specifically designed for geologists. The challenge was to deliver a system that would feel sufficiently close to the flexibility of paper-based geological mapping while being implemented on a consumer communication and entertainment device. The first release of a tablet-based geological mapping system from this project is illustrated and will be shown as implemented on an iPad during the poster session. Midland Valley is pioneering tablet-based mapping and, along with its industrial and academic partners, will be using the application in field based projects throughout this year and will be integrating feedback in further developments of this technology.

Differences in fundamental and functional properties of HPMC co-processed fillers prepared by fluid-bed coating and spray drying.

Science.gov (United States)

Dong, QianQian; Zhou, MiaoMiao; Lin, Xiao; Shen, Lan; Feng, Yi

2018-07-01

This study aimed to develop novel co-processed tablet fillers based on the principle of particle engineering for direct compaction and to compare the characteristics of co-processed products obtained by fluid-bed coating and co-spray drying, respectively. Water-soluble mannitol and water-insoluble calcium carbonate were selected as representative fillers for this study. Hydroxypropyl methylcellulose (HPMC), serving as a surface property modifier, was distributed on the surface of primary filler particles via the two co-processing methods. Both fundamental and functional properties of the products were comparatively investigated. The results showed that functional properties of the fillers, like flowability, compactibility, and drug-loading capacity, were effectively improved by both co-processing methods. However, fluid-bed coating showed greater advantages over co-spray drying in some aspects, which was mainly attributed to the remarkable differences in some fundamental properties of co-processed powders, like particle size, surface topology, and particle structure. For example, the more irregular surface and porous structure induced by fluid-bed coating could contribute to better compaction properties and lower lubricant sensitivity due to the increasing contact area and mechanical interlocking between particles under pressure. More effective surface distribution of HPMC during fluid-bed coating was also a contributor. In addition, such a porous agglomerate structure could also reduce the separation of drug and excipients after mixing, resulting in the improvement in drug loading capacity and tablet uniformity. In summary, fluid-bed coating appears to be more promising for co-processing than spray drying in some aspects, and co-processed excipients produced by it have a great prospect for further investigations and development. Copyright © 2018 Elsevier B.V. All rights reserved.

21 CFR 520.2362 - Thenium closylate tablets.

Science.gov (United States)

2010-04-01

....2362 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED...) Conditions of use. (1) The tablets are administered orally to dogs as a single day treatment of canine... Uncinaria stenocephala (hookworms). Dogs weighing 10 pounds and over are administered 1 tablet as a single...

Active Reading Behaviors in Tablet-Based Learning

Science.gov (United States)

Palilonis, Jennifer; Bolchini, Davide

2015-01-01

Active reading is fundamental to learning. However, there is little understanding about whether traditional active reading frameworks sufficiently characterize how learners study multimedia tablet textbooks. This paper explores the nature of active reading in the tablet environment through a qualitative study that engaged 30 students in an active…

Mechanism by Which Magnesium Oxide Suppresses Tablet Hardness Reduction during Storage.

Science.gov (United States)

Sakamoto, Takatoshi; Kachi, Shigeto; Nakamura, Shohei; Miki, Shinsuke; Kitajima, Hideaki; Yuasa, Hiroshi

2016-01-01

This study investigated how the inclusion of magnesium oxide (MgO) maintained tablet hardness during storage in an unpackaged state. Tablets were prepared with a range of MgO levels and stored at 40°C with 75% relative humidity for up to 14 d. The hardness of tablets prepared without MgO decreased over time. The amount of added MgO was positively associated with tablet hardness and mass from an early stage during storage. Investigation of the water sorption properties of the tablet components showed that carmellose water sorption correlated positively with the relative humidity, while MgO absorbed and retained moisture, even when the relative humidity was reduced. In tablets prepared using only MgO, a petal- or plate-like material was observed during storage. Fourier transform infrared spectrophotometry showed that this material was hydromagnesite, produced when MgO reacts with water and CO2. The estimated level of hydromagnesite at each time-point showed a significant negative correlation with tablet porosity. These results suggested that MgO suppressed storage-associated softening by absorbing moisture from the environment. The conversion of MgO to hydromagnesite results in solid bridge formation between the powder particles comprising the tablets, suppressing the storage-related increase in volume and increasing tablet hardness.

A classification system for tableting behaviors of binary powder mixtures

Directory of Open Access Journals (Sweden)

Changquan Calvin Sun

2016-08-01

Full Text Available The ability to predict tableting properties of a powder mixture from individual components is of both fundamental and practical importance to the efficient formulation development of tablet products. A common tableting classification system (TCS of binary powder mixtures facilitates the systematic development of new knowledge in this direction. Based on the dependence of tablet tensile strength on weight fraction in a binary mixture, three main types of tableting behavior are identified. Each type is further divided to arrive at a total of 15 sub-classes. The proposed classification system lays a framework for a better understanding of powder interactions during compaction. Potential applications and limitations of this classification system are discussed.

Absorption from iron tablets given with different types of meals

International Nuclear Information System (INIS)

Hallberg, L.; Bjoern-Rasmussen, E.; Ekenved, G.; Garby, L.; Rossander, L.; Pleehachinda, R.; Suwanik, R.; Arvidsson, B.

1978-01-01

The absorption from iron tablets given with 5 types of meals was studied in 153 subjects. The meals were: a hamburger meal with beans and potatoes, a simple breakfast meal, a Latin American meal composed of black beans, rice and maize and two Southeast Asian meals composed of rice, vegetables, and spices served with and without fish. The groups were directly compared by relating the absorption from the iron tablets to the absorption from a standardized reference dose of iron given on an empty stomach. The composition of meals with respect to content of meat or fish or the presence of large amounts of phytates seemed to have no influence on the absorption of iron from tablets. The absorption from iron tablets was about 40% higher when they were given with rice meals than when they were given with the other meals studied. The average decrease in absorption by meals was about 50-60% based on a comparison when tablets were given on an empty stomach. When tablets from which the iron was released more slowly were used, the absorption increased by about 30% except when they were given with rice meals, where the absorption was unchanged. The differences among the meals in their effect on the absorption of iron from tablets thus disappeared when the slow-release tablets were given. (author)

Absorption from iron tablets given with different types of meals

Energy Technology Data Exchange (ETDEWEB)

Hallberg, L; Bjoern-Rasmussen, E; Ekenved, G; Garby, L; Rossander, L; Pleehachinda, R; Suwanik, R; Arvidsson, B

1978-01-01

The absorption from iron tablets given with 5 types of meals was studied in 153 subjects. The meals were: a hamburger meal with beans and potatoes, a simple breakfast meal, a Latin American meal composed of black beans, rice and maize and two Southeast Asian meals composed of rice, vegetables, and spices served with and without fish. The groups were directly compared by relating the absorption from the iron tablets to the absorption from a standardized reference dose of iron given on an empty stomach. The composition of meals with respect to content of meat or fish or the presence of large amounts of phytates seemed to have no influence on the absorption of iron from tablets. The absorption from iron tablets was about 40% higher when they were given with rice meals than when they were given with the other meals studied. The average decrease in absorption by meals was about 50-60% based on a comparison when tablets were given on an empty stomach. When tablets from which the iron was released more slowly were used, the absorption increased by about 30% except when they were given with rice meals, where the absorption was unchanged. The differences among the meals in their effect on the absorption of iron from tablets thus disappeared when the slow-release tablets were given.

Absorption from iron tablets given with different types of meals.

Science.gov (United States)

Hallberg, L; Björn-Rasmussen, E; Ekenved, G; Garby, L; Rossander, L; Pleehachinda, R; Suwanik, R; Arvidsson, B

1978-09-01

The absorption of iron from tablets given with 5 types of meals was studied in 153 subjects. The meals were: a hamburger meal with beans and potatoes, a simple breakfast meal, a Latin American meal composed of black beans, rice and maize and two Southeast Asian meals composed of rice, vegetables and spices served with and without fish. The groups were directly compared by relating the absorption from the iron tablets to the absorption from a standardized reference dose of iron given on an empty stomach. The composition of meals with respect to content of meat or fish or the presence of large amounts of phytates seemed to have no influence on the absorption of iron from tablets. The absorption from iron tablets was about 40% higher when they were given with rice meals than when they were given with the other meals studied. The average decrease in absorption by meals was about 50-60% based on a comparison when tablets were given on an empty stomach. When tablets from which the iron was released more slowly were used, the absorption increased by about 30% except when they were given with rice meals, where the absorption was unchanged. The differences among the meals in their effect on the absorption of iron from tablets thus disappeared when the slow-release tablets were given.

Preparation and scale up of extended-release tablets of bromopride

Directory of Open Access Journals (Sweden)

Guilherme Neves Ferreira

2014-04-01

Full Text Available Reproducibility of the tablet manufacturing process and control of its pharmaceutics properties depends on the optimization of formulation aspects and process parameters. Computer simulation such as Design of Experiments (DOE can be used to scale up the production of this formulation, in particular for obtaining sustained-release tablets. Bromopride formulations are marketed in the form of extended-release pellets, which makes the product more expensive and difficult to manufacture. The aim of this study was to formulate new bromopride sustained release formulations as tablets, and to develop mathematical models to standardize the scale up of this formulation, controlling weight and hardness of the tablets during manufacture according to the USP 34th edition. DOE studies were conducted using Minitab(tm software. Different excipient combinations were evaluated in order to produce bromopride sustained-release matrix tablets. In the scale-up study, data were collected and variations in tableting machine parameters were measured. Data were processed by Minitab(tm software, generating mathematical equations used for prediction of powder compaction behavior, according to the settings of the tableting machine suitable for scale-up purposes. Bromopride matrix tablets with appropriate characteristics for sustained release were developed. The scale-up of the formulation with the most suitable sustained release profile was established by using mathematical models, indicating that the formulation can be a substitute for the pellets currently marketed.

Ultrasound transmission measurements for tensile strength evaluation of tablets.

Science.gov (United States)

Simonaho, Simo-Pekka; Takala, T Aleksi; Kuosmanen, Marko; Ketolainen, Jarkko

2011-05-16

Ultrasound transmission measurements were performed to evaluate the tensile strength of tablets. Tablets consisting of one ingredient were compressed from dibasic calcium phosphate dehydrate, two grades of microcrystalline cellulose and two grades of lactose monohydrate powders. From each powder, tablets with five different tensile strengths were directly compressed. Ultrasound transmission measurements were conducted on every tablet at frequencies of 2.25 MHz, 5 MHz and 10 MHz and the speed of sound was calculated from the acquired waveforms. The tensile strength of the tablets was determined using a diametrical mechanical testing machine and compared to the calculated speed of sound values. It was found that the speed of sound increased with the tensile strength for the tested excipients. There was a good correlation between the speed of sound and tensile strength. Moreover, based on the statistical tests, the groups with different tensile strengths can be differentiated from each other by measuring the speed of sound. Thus, the ultrasound transmission measurement technique is a potentially useful method for non-destructive and fast evaluation of the tensile strength of tablets. Copyright © 2011 Elsevier B.V. All rights reserved.

Formulation of Fast-Dissolving Tablets of Promethazine Theoclate

African Journals Online (AJOL)

Erah

tablet containing β-cyclodextrin, crospovidone, and camphor, using direct compression method. A 33 full factorial design ... fast dissolving tablets (FDT) is the use of ... All the raw materials were passed ..... delivery systems: critical review in.

Actual and Potential Pedagogical Use of Tablets in Schools

Directory of Open Access Journals (Sweden)

Jenni Rikala

2013-01-01

Full Text Available This study reviews the potential of tablet technology for teaching and learning. In autumn 2012, we conducted a focused survey comprising quantitative and qualitative questions with Finnish teachers (N = 171, from 54 schools. We focused on perceived pedagogical opportunities and the actualized pedagogical potential of tablets at schools. The survey results indicate that the actual usefulness of tablets in schools was significantly less than what teachers perceived as the pedagogical potential. However, the results demonstrate the positive impact these devices are having on teaching and learning, as well as prompting changes in pedagogical perspectives. Teachers stated that tablets can diversify and enhance teaching and learning in many ways, particularly in supporting learners’ motivation and independent learning, and promoting engaging teaching methods. Nevertheless, teachers voiced concern that the student-to-device ratio at the moment is too low, thus serving as a barrier to widespread use of tablets.

[Formulation optimization of panax notoginsenoside orally fast disintegration tablets].

Science.gov (United States)

Wang, Zhi; Wei, Li; Chen, Ting

2008-07-01

To optimize the formulation of panax notoginsenoside orally fast disintegrating tablets. Mannitol, microcrystalline cellulose (PH 102) and lactose 80 were used as diluent. A polynomial regression algorithm was used to evaluate the relationship between the controlling factor, compacting pressure and diluent ratio, and disintegration time, tensile strength of tablets. Optimum formulation and process parameters could be determined by contrast the contour plot of tensile strength to that of disintegration time. The disintegration time and tensile strength of panax notoginsenoside oral disintegrating tablets were good, and the taste was satisfactory. Panax notoginsenoside oral disintegrating tablets achieve the goal of design and this method can be fairly used in formulation screening.

Characterising the disintegration properties of tablets in opaque media using texture analysis.

Science.gov (United States)

Scheuerle, Rebekah L; Gerrard, Stephen E; Kendall, Richard A; Tuleu, Catherine; Slater, Nigel K H; Mahbubani, Krishnaa T

2015-01-01

Tablet disintegration characterisation is used in pharmaceutical research, development, and quality control. Standard methods used to characterise tablet disintegration are often dependent on visual observation in measurement of disintegration times. This presents a challenge for disintegration studies of tablets in opaque, physiologically relevant media that could be useful for tablet formulation optimisation. This study has explored an application of texture analysis disintegration testing, a non-visual, quantitative means of determining tablet disintegration end point, by analysing the disintegration behaviour of two tablet formulations in opaque media. In this study, the disintegration behaviour of one tablet formulation manufactured in-house, and Sybedia Flashtab placebo tablets in water, bovine, and human milk were characterised. A novel method is presented to characterise the disintegration process and to quantify the disintegration end points of the tablets in various media using load data generated by a texture analyser probe. The disintegration times in the different media were found to be statistically different (Pdisintegration times from each other in human versus bovine milk (adjusted P value 0.1685). Copyright © 2015 Elsevier B.V. All rights reserved.

Preventive distribution and plans of iodine tablets stocks management

International Nuclear Information System (INIS)

2002-01-01

This official note includes two parts: one concerns the new preventive distribution of iodine tablets on the areas defined by the Particular Intervention Plans (P.P.I.) around nuclear facilities and the other one the setting up of iodine tablets stocks beyond the P.P.I. areas. In annexe is a guide for the elaboration of stocks management plans for steady iodine tablets. (N.C.)

Bioavailability of everolimus administered as a single 5 mg tablet versus five 1 mg tablets: a randomized, open-label, two-way crossover study of healthy volunteers.

Science.gov (United States)

Thudium, Karen; Gallo, Jorge; Bouillaud, Emmanuel; Sachs, Carolin; Eddy, Simantini; Cheung, Wing

2015-01-01

The mammalian target of rapamycin (mTOR) inhibitor everolimus has a well-established pharmacokinetics profile. We conducted a randomized, single-center, open-label, two-sequence, two-period crossover study of healthy volunteers to assess the relative bioavailability of everolimus administered as one 5 mg tablet or five 1 mg tablets. Subjects were randomized 1:1 to receive everolimus dosed as one 5 mg tablet or as five 1 mg tablets on day 1, followed by a washout period on days 8-14 and then the opposite formulation on day 15. Blood sampling for pharmacokinetic evaluation was performed at prespecified time points, with 17 samples taken for each treatment period. Primary variables for evaluation of relative bioavailability were area under the concentration-time curve from time zero to infinity (AUCinf) and maximum blood concentration (Cmax). Safety was assessed by reporting the incidence of adverse events (AEs). Twenty-two participants received everolimus as one 5 mg tablet followed by five 1 mg tablets (n=11) or the opposite sequence (n=11). The Cmax of five 1 mg tablets was 48% higher than that of one 5 mg tablet (geometric mean ratio, 1.48; 90% confidence interval [CI], 1.35-1.62). AUCinf was similar (geometric mean ratio, 1.08; 90% CI, 1.02-1.16), as were the extent of absorption and the distribution and elimination kinetics. AEs, all grade 1 or 2, were observed in 54.5% of subjects. Although the extent of absorption was similar, the Cmax of five 1 mg tablets was higher than that of one 5 mg tablet, suggesting these formulations lead to different peak blood concentrations and are not interchangeable at the dose tested.

Fast Dissolving Tablets of Aloe Vera Gel | Madan | Tropical Journal ...

African Journals Online (AJOL)

Purpose: The objective of this work was to prepare and evaluate fast dissolving tablets of the nutraceutical, freeze dried Aloe vera gel. Methods: Fast dissolving tablets of the nutraceutical, freeze-dried Aloe vera gel, were prepared by dry granulation method. The tablets were evaluated for crushing strength, disintegration ...

Quality of Artesunate Tablets Sold in Pharmacies in Kumasi, Ghana ...

African Journals Online (AJOL)

Purpose: The study was carried out to evaluate the quality of artesunate tablets sold in retail and wholesale pharmacies in Kumasi, Ghana. In particular, the study sought to ascertain the presence or otherwise of counterfeit artesunate tablets in Kumasi. Method: Artesunate tablets were purchased from pharmacies in Kumasi ...

Variability in the 3,4-methylenedioxymethamphetamine content of 'ecstasy' tablets in the UK.

Science.gov (United States)

Wood, David Michael; Stribley, Vasoulla; Dargan, Paul Ivor; Davies, Susannah; Holt, David W; Ramsey, John

2011-09-01

Toxicity, such as hyperpyrexia, associated with the use of 3,4-methylenedioxymethamphetamine (MDMA; 'ecstasy') appears to be related to serum MDMA concentrations. However, there does not appear to be a similar association with the number of tablets ingested, suggesting variation in the tablet content of MDMA. Although work has shown this variation in other areas of the world, no studies have reported on the variation of MDMA content in UK ecstasy tablets. Ecstasy tablets seized from individuals attending nightclubs were analysed qualitatively to determine if they contained MDMA and quantitatively to determine the MDMA content per tablet. The mean amount of MDMA hydrochloride in 101 seized ecstasy tablets was 58.7±22.9 mg per tablet, with a range of 20 mg to 131 mg per tablet. The majority (96.0%) of tablets contained less than 100 mg MDMA per tablet. There appeared to be a bimodal distribution of MDMA content at approximately 20-40 mg per tablet and 60-80 mg per tablet. There is variability in the MDMA content of ecstasy tablets in the UK. This variability could potentially put users at increased risk of acute harm due to inadvertent excess ingestion of MDMA, as they are unaware of the differences in the MDMA content. Repeat sampling and quantification of MDMA content of ecstasy tablets in the UK will allow better education of users about the potential harms associated with the variability in the MDMA content. In addition, it will provide information to allow the monitoring of changes in not only the MDMA content, but also other adulterants, in ecstasy tablets.

Exploration of the associations of touch-screen tablet computer usage and musculoskeletal discomfort.

Science.gov (United States)

Chiang, Hsin-Yu Ariel; Liu, Chien-Hsiou

2016-03-10

Tablet users may be at high risk of developing physical discomfort because of their usage behaviors and tablet design. Investigate the usage of tablets, variations in head and neck posture associated with different tablet tilt angles, and the association of tablet use with users' musculoskeletal discomfort. A survey of users' subjective perceptions conducted by questionnaire and measurements of users' postures by a 3D Motion analysis system was used to explore the effects of tablet use. The questionnaire results indicated that over half of the participants reported physical discomfort after using tablets, with the most prevalent discomfort in the neck and shoulders, and more intensity of discomfort for the back although only few participants experienced it. Chi-squared tests indicated that significantly more participants who tended to use tablet computers to play games reported having musculoskeletal discomfort after using a tablet. In addition, preferences for tablet tilt angles varied across tasks (reading and game playing). The results from the 3D motion analysis revealed that head and neck flexion angles were significantly reduced when the tablets were positioned at relatively steep tilt angles. Neck flexion angle was significantly higher in game playing. These data add information regarding to the usage of tablet and its associations with physical discomfort (significantly more participants who tended to use tablet computers to play games reported having musculoskeletal discomfort after using a tablet). Steep tilt angles (such as 60°) may cause tablet users to decrease their head and neck flexion angles, which could lead to a more neutral, effortless, and ergonomically correct posture. Maintaining proper neck posture during active activities such as game playing is recommended to avoid neck discomfort.

Improving the hardness of dry granulated tablets containing sodium lauryl sulfate.

Science.gov (United States)

Moore, Francis; Okelo, Geoffrey; Colón, Ivelisse; Kushner, Joseph

2010-11-15

The impact of the addition of a wetting agent, the surfactant sodium lauryl sulfate (SLS), on the tablet hardness of a dry granulated, solid oral dosage form was investigated. In three batches, SLS was added concurrently with: (1) a poorly soluble, highly hydrophobic active pharmaceutical ingredient (API) and the other excipients prior to the initial blending step, (2) magnesium stearate prior to roller compaction, or (3) magnesium stearate prior to tableting. A fourth batch, which did not contain SLS, served as a control. The maximum hardness of 100 mg, 1/4″-SRC tablets for the four batches--SLS added initially, prior to roller compaction, prior to tableting, and no SLS--were 61±3, 71±3, 89±5, and 86±3N, respectively, suggesting reduced processing of SLS improves tablet hardness by ∼50%. Dissolution of the tablets in 900 ml of simulated gastric fluid with paddles at 75 rpm showed that: (1) there was no impact on the insertion point of SLS into the process on API dissolution, and (2) that the presence of SLS improved dissolution by 5% compared to the control tablets. Adding SLS just prior to tableting can improve tablet hardness and yield similar dissolution performance relative to SLS addition prior to the initial blending step. Copyright © 2010 Elsevier B.V. All rights reserved.

Oral Delivery of Probiotics in Poultry Using pH-Sensitive Tablets.

Science.gov (United States)

Jiang, Tao; Li, Hui-Shan; Han, Geon Goo; Singh, Bijay; Kang, Sang-Kee; Bok, Jin-Duck; Kim, Dae-Duk; Hong, Zhong-Shan; Choi, Yun-Jaie; Cho, Chong-Su

2017-04-28

As alternatives to antibiotics in livestocks, probiotics have been used, although most of them in the form of liquid or semisolid formulations, which show low cell viability after oral administration. Therefore, suitable dry dosage forms should be developed for livestocks to protect probiotics against the low pH in the stomach such that the products have higher probiotics survivability. Here, in order to develop a dry dosage forms of probiotics for poultry, we used hydroxypropyl methylcellulose phthalate 55 (HPMCP 55) as a tablet-forming matrix to develop probiotics in a tablet form for poultry. Here, we made three different kinds of probiotics-loaded tablet under different compression forces and investigated their characteristics based on their survivability, morphology, disintegration time, and kinetics in simulated gastrointestinal fluid. The results indicated that the probiotics formulated in the tablets displayed higher survival rates in acidic gastric conditions than probiotics in solution. Rapid release of the probiotics from the tablets occurred in simulated intestinal fluid because of fast swelling of the tablets in neutral pH. As a matrix of tablet, HPMCP 55 provided good viability of probiotics after 6 months under refrigeration. Moreover, after oral administration of probiotics-loaded tablets to chicken, more viable probiotics were observed, than with solution type, through several digestive areas of chicken by the tablets.

Optimasi Tablet Levofloksasin yang Mengandung Bahan Pengikat PVP K-30 dan Disintegran Vivasol

Directory of Open Access Journals (Sweden)

Dina Ayu Fatmawati

2017-12-01

Full Text Available The aim of this research was to get optimal formula of levofloxacin tablet prepared with variation of PVP K-30 as binder and vivasol as disintegrant. The making of levofloxacin tablets was done by wet granulation. Tablet was prepared with various levels of PVP K-30 and disintegrant vivasol, compressed using a hydraulic press with 12 mm punch diameter, for 3 seconds. Physical quality (hardness, friability, and disintegration time and dissolution rate of tablet was evaluated. The optimization of the formula was done by factorial design of 22 factorial experiments with 2 factors (PVP K-30 and vivasol and 2 levels (2% and 4%. Optimization results showed that elevated levels of PVP K-30 increased tablet hardness, reduced friability of tablet, decreased disintegrating time, and increased dissolution rate of levofloxacin tablets. Meanwhile, elevated levels of vivasol increased the hardness of tablets, decreased the disintegrating time of tablets, decreased the dissolution rate of levofloxacin tablets, but did not affect the friability of tablets. In conclusion, the optimal tablet that meet the specifications of physical quality (hardness, friability, and disintegrating time and dissolution rate was made by 2.4 to 3.7% of PVP K-30 and 2.0 to 3.2% vivasol as shown in the feasible area of design space.

Isoniazid, pyrazinamide and rifampicin content variation in split fixed-dose combination tablets.

Science.gov (United States)

Pouplin, Thomas; Phuong, Pham Nguyen; Toi, Pham Van; Nguyen Pouplin, Julie; Farrar, Jeremy

2014-01-01

In most developing countries, paediatric tuberculosis is treated with split tablets leading to potential inaccuracy in the dose delivery and drug exposure. There is no data on the quality of first-line drugs content in split fixed-dose combination tablets. To determine Isoniazid, Pyrazinamide and Rifampicin content uniformity in split FDC tablets used in the treatment of childhood tuberculosis. Drug contents of 15 whole tablets, 30 half tablets and 36 third tablets were analysed by high performance liquid chromatography. The content uniformity was assessed by comparing drug content measured in split portions with their expected amounts and the quality of split portions was assessed applying qualitative specifications for whole tablets. All whole tablets measurements fell into the USP proxy for the three drugs. But a significant number of half and third portions was found outside the tolerated variation range and the split formulation failed the requirements for content uniformity. To correct for the inaccuracy of splitting the tablets into equal portions, a weight-adjustment strategy was used but this did not improve the findings. In split tablets the content of the three drugs is non-uniform and exceeded the USP recommendations. There is an absolute need to make child-friendly formulations available for the treatment of childhood tuberculosis.

The present and the future of the tablet periodicals in Czech Republic

OpenAIRE

Kubíčková, Jana Ada

2016-01-01

The Thesis maps the Czech tablet magazine market tablet and describes possible approaches to tablet magazines' creation and distribution. First chapter outlines the historical timeline of tablet magazines development both in the Czech Republic and abroad, and maps the current situation of the Czech market. The chapter defines a concept of "strictly tablet magazine" and presents possible approaches to a production of such magazines. The following chapter analyses the concept from the new media...

Hydration induced material transfer in membranes of osmotic pump tablets measured by synchrotron radiation based FTIR.

Science.gov (United States)

Wu, Li; Yin, Xianzhen; Guo, Zhen; Tong, Yajun; Feng, Jing; York, Peter; Xiao, Tiqiao; Chen, Min; Gu, Jingkai; Zhang, Jiwen

2016-03-10

Osmotic pump tablets are reliable oral controlled drug delivery systems based on their semipermeable membrane coating. This research used synchrotron radiation-based Fourier transform infrared (SR-FTIR) microspectroscopy and imaging to investigate the hydration induced material transfer in the membranes of osmotic pump tablets. SR-FTIR was applied to record and map the chemical information of a micro-region of the membranes, composed of cellulose acetate (CA, as the water insoluble matrix) and polyethylene glycol (PEG, as the soluble pore forming agent and plasticizing agent). The microstructure and chemical change of membranes hydrated for 0, 5, 10 and 30min were measured using SR-FTIR, combined with scanning electronic microscopy and atom force microscopy. The SR-FTIR microspectroscopy results indicated that there was a major change at the absorption range of 2700-3100cm(-1) in the membranes after different periods of hydration time. The absorption bands at 2870-2880cm(-1) and 2950-2960cm(-1) were assigned to represent CA and PEG, respectively. The chemical group signal distribution illustrated by the ratio of PEG to CA demonstrated that the trigger of drug release in the preliminary stage was due to the rapid transfer of PEG into liquid medium with a sharp decrease of PEG in the membranes. The SR-FTIR mapping results have demonstrated the hydration induced material transfer in the membranes of osmotic pump tablets and enabled reassessment of the drug release mechanism of membrane controlled osmotic pump systems. Copyright © 2016 Elsevier B.V. All rights reserved.

How Tablets Are Utilized in the Classroom

Science.gov (United States)

Ditzler, Christine; Hong, Eunsook; Strudler, Neal

2016-01-01

New technologies are a large part of the educational landscape in the 21st century. Emergent technologies are implemented in the classroom at an exponential rate. The newest technology to be added to the daily classroom is the tablet computer. Understanding students' and teachers' perceptions about the role of tablet computers is important as this…

Determination of uranium by luminescent method (tablet variant)

International Nuclear Information System (INIS)

Sergeev, A.N.; Yufa, B.Ya.

1985-01-01

A new tablet variant of luminescent determination of uranium in rocks is developed. The analytical process includes the following operations: sample decomposition, uranium separation from luminescence quencher impurities, preparation of luminescent sample (tablet), photometry of the tablet. The method has two variants developed: the first one is characterized by a more hard decomposition, sample mass being 0.2 g; the second variant has a better detection limit (5x10 -6 %), the sample mass being 0.2-1 g. Procedures of the sample preparation for both variants of analysis are described

Effects of protoporphyrin disodium (Prolmon tablets) during radiotherapy

International Nuclear Information System (INIS)

Iwata, Takeo; Fukutomi, Toshio

1981-01-01

Effects of Prolmon tablets (medicine for hepatitis) on radiation syndrome (fatigue, nausea, vomiting, etc) which appeared during an early stage of radiotherapy were studied. Two tablets of Prolmon were administered to 10 patients with various tumors three times a day with concurrent use of other medicines during radiotherapy. A marked change in GOT and GPT values did not found, and the treatment was completed without any radiation syndrome in all patients. It was suggested that the administration of Prolmon tablets together with nutrients and vitamine preparations was effective to prevent radiation syndrome. (Tsunoda, M.)

Bioavailability of syrup and tablet formulations of cefetamet pivoxil.

Science.gov (United States)

Ducharme, M P; Edwards, D J; McNamara, P J; Stoeckel, K

1993-12-01

Two studies examining the bioavailability of cefetamet pivoxil in healthy male subjects were conducted. In the first, the bioavailabilities of the 250-mg (M250) and M500 tablet formulations of cefetamet pivoxil to be marketed were compared with that of a tablet used in clinical trials. All products were given with food at a dose of 500 mg. In the second study, the bioavailability of the syrup formulation was evaluated under both fasting and nonfasting conditions and compared with that of the M500 tablet formulation given with food. The absolute bioavailabilities of the M500 and M250 tablets (55.0% +/- 8.0% and 55.7% +/- 7.0%, respectively) were not significantly different from that of the clinical-trial formulation (49.8% +/- 8.5%). The newer tablet formulations exhibited faster absorption as evidenced by higher peak concentrations (3.8 [M500] and 3.9 [M250] mg/liter compared with 3.2 mg/liter for the clinical-trial formulation), a shorter time to peak concentration, and a shorter mean absorption time. The syrup formulation was found to have significantly lower absolute bioavailability (37.9% +/- 6.0%) compared with that of the M500 tablet (58.4% +/- 9.0%) when both were given with food. Food had no significant effect on the bioavailability of the syrup, which averaged 34.0% +/- 8.6% under fasting conditions, although absorption was delayed by food (mean absorption time increased from 2.2 to 3.9 h). This contrasts with the results of previous studies documenting significant increases in tablet bioavailability with food. Despite the lower bioavailability of the syrup, unbound-cefetamet concentrations are expected to remain above the MICs for 90% of the strains tested for susceptible organisms for approximately 10 h of the usual 12-h dosing interval with both syrup and tablet formulations of cefetamet pivoxil given with food.

Why do adult women in Vietnam take iron tablets?

Directory of Open Access Journals (Sweden)

Zhao Yun

2006-06-01

Full Text Available Abstract Background Conducting iron supplementation programs has been a major strategy to reduce iron deficiency anemia in pregnancy. However, only a few countries have reported improvements in the anemia rate at a national level. The strategies used for control of nutrition problems need regular review to maintain and improve their effectiveness. The objective of this study was to analyze the factors in compliance with taking iron tablets, where daily doses of iron (60 mg and folic acid (400 μg were distributed in rural Vietnamese communes. Methods A cross sectional survey was conducted in Nghe An province, Vietnam in January, 2003. The study population was adult women aged less than 35 years who delivered babies between August 1st 2001 and December 1st 2002 (n = 205, of which 159 took part in the study. Data for the study were collected from a series of workshops with community leaders, focus group discussions with community members and a questionnaire survey. Results Improvements in the rate of anemia was not given a high priority as one of the commune's needs, but the participants still made efforts to continue taking iron tablets. Two major factors motivated the participants to continue taking iron tablets; their experience of fewer spells of dizziness (50%, and their concern for the health of their newborn baby (54%. When examining the reasons for taking iron tablets for at least 5–9 months, the most important factor was identified as 'a frequent supply of iron tablets' (OR = 11.93, 95% CI: 4.33–32.85. Conclusion The study found that multiple poor environmental risk factors discouraged women from taking iron tablets continuously. The availability (frequent supply of iron tablets was the most effective way to help adult women to continue taking iron tablets.

Tablets Helping Elderly and Disabled People

OpenAIRE

Castro, Mercedes de; Ruiz-Mezcua, Belén; Sánchez-Pena, José Manuel; García-Crespo, Ángel; Iglesias, Ana; Pajares, José Luis

2012-01-01

Proceedings of: Ambient Assisted Living Joint Programme Forum 2011 (AAL JP Forum 2011), Lecce (Italy), September 26-28, 2011 The article introduces the basics by which tablets are considered as appropriate tools for integration and promotion of the elderly in the digital world. To prove this, the paper presents three research projects carried out by CESyA that integrate Automatic Speech Recognition (ASR), Voice Synthesis, subtitling, audiodescription or audio navigation tools into tablets ...

Assessment of Albizia zygia gum as binding agent in tablet formulations

OpenAIRE

ODEKU, OLUWATOYIN A.

2005-01-01

Albizia gum has been evaluated as a binding agent in tablet formulations in comparison with gelatin BP. Compressional properties were analyzed using density measurements and the compression equations of Heckel and Kawakita as assessment parameters, while the mechanical properties of the tablets were assessed using the crushing strength and friability of the tablets. Drug release properties of the tablets were assessed using disintegration time and dissolution time as assessment parameters. Fo...

Student Perceptions of Using Tablet Technology in Post-Secondary Classes

Science.gov (United States)

Mang, Colin F.; Wardley, Leslie J.

2013-01-01

This paper assesses students' attitudes towards using tablets, such as the Apple iPad, in university classes. Tablets are found to be a substitute for laptop computers. Students initially expressed a great deal of optimism regarding the technology, and, although their views diminished slightly as they gained experience with using a tablet,…

Fused-filament 3D printing (3DP) for fabrication of tablets.

Science.gov (United States)

Goyanes, Alvaro; Buanz, Asma B M; Basit, Abdul W; Gaisford, Simon

2014-12-10

The use of fused-filament 3D printing (FF 3DP) to fabricate individual tablets is demonstrated. The technology permits the manufacture of tablets containing drug doses tailored to individual patients, or to fabrication of tablets with specific drug-release profiles. Commercially produced polyvinyl alcohol (PVA) filament was loaded with a model drug (fluorescein) by swelling of the polymer in ethanolic drug solution. A final drug-loading of 0.29% w/w was achieved. Tablets of PVA/fluorescein (10 mm diameter) were printed using a 3D printer. It was found that changing the degree of infill percentage in the printer software varied the weight and volume of the printed tablets. The tablets were mechanically strong and no significant thermal degradation of the active occurred during printing. Dissolution tests were conducted in modified Hank's buffer. The results showed release profiles were dependent on the infill percentage used to print the tablet. The study indicates that FF 3DP has the potential to offer a new solution for fabricating personalized-dose medicines or unit dosage forms with controlled-release profiles. In addition, the low cost of FDM printers means the paradigm of extemporaneous or point-of-use manufacture of personalized-dose tablets is both feasible and attainable. Copyright © 2014 Elsevier B.V. All rights reserved.

Distribution of crushing strength of tablets

DEFF Research Database (Denmark)

Sonnergaard, Jørn

2002-01-01

The distribution of a given set of data is important since most parametric statistical tests are based on the assumption that the studied data are normal distributed. In analysis of fracture mechanics the Weibull distribution is widely used and the derived Weibull modulus is interpreted as a mate...... data from nine model tablet formulations and four commercial tablets are shown to follow the normal distribution. The importance of proper cleaning of the crushing strength apparatus is demonstrated....

Triiodothyronine and thyroxine content of desiccated thyroid tablets.

Science.gov (United States)

Rees-Jones, R W; Larsen, P R

1977-11-01

Triiodothyronine (T3) and thyroxine (T4) were measured by radioimmunoassay in Pronase hydrolysates of four lots each of 1- and 2-grain tablets of desiccated thyroid (Thyroid, Armour) and thyroglobulin (Proloid, Warner-Chilcott). The methodology used was verified by studies of tablets containing known quantities of T4 and T3. One grain of desiccated thyroid contained 12 +/- 1 and 64 +/- 3 microgram (mean +/- SD) of T3 and T4 per tablet, respectively (T4/T3 molar ratio, 4.3). A 1-grain tablet of thyroglobulin contained 16 +/- 2 and 55 +/- 5 microgram of T3 and T4, respectively with a T4/T3 ratio of 2.9. Two-grain tablets generally contained twice the quantity of T3 and T4 in the 1-grain preparations. The variation in T3 and T4 content between the four lots of each tablet strength for each product was 10% or less. These estimates of T3 and T4 content are 1.5- to 2-fold greater than those previously published. This difference probably results from the more sophisticated methodology now available which does not require chromatographic separation of T3 and T4 or iodometry. Using calculations based on published estimates of T4 and T3 absorption and of the T3/T4 potency ratio, it would appear that the T3 content of desiccated thyroid and thyroglobulin provide approximately 39% and 51%, respectively, of the thyromimetic activity of these two medications.

Formulation and evaluation of aceclofenac mouth-dissolving tablet

Directory of Open Access Journals (Sweden)

Shailendra Singh Solanki

2011-01-01

Full Text Available Aceclofenac has been shown to have potent analgesic and anti-inflammatory activities similar to indomethacin and diclofenac, and due to its preferential Cox-2 blockade, it has a better safety than conventional Non steroidal anti-inflammatory drug (NSAIDs with respect to adverse effect on gastrointestinal and cardiovascular systems. Aceclofenac is superior from other NSAIDs as it has selectivity for Cox-2, a beneficial Cox inhibitor is well tolerated, has better Gastrointestinal (GI tolerability and improved cardiovascular safety when compared with other selective Cox-2 inhibitor. To provide the patient with the most convenient mode of administration, there is need to develop a fast-disintegrating dosage form, particularly one that disintegrates and dissolves/disperses in saliva and can be administered without water, anywhere, any time. Such tablets are also called as "melt in mouth tablet." Direct compression, freeze drying, sublimation, spray drying, tablet molding, disintegrant addition, and use of sugar-based excipients are technologies available for mouth-dissolving tablet. Mouth-dissolving tablets of aceclofenac were prepared with two different techniques, wet granulation and direct compression, in which different formulations were prepared with varying concentration of excipients. These tablets were evaluated for their friability, hardness, wetting time, and disintegration time; the drug release profile was studied in buffer Phosphate buffered Saline (PBS pH 7.4. Direct compression batch C3 gave far better dissolution than the wet granulation Batch F2, which released only 75.37% drug, and C3, which released 89.69% drug in 90 minutes.

FAKTOR-FAKTOR YANG BERHUBUNGAN DENGAN KEPATUHAN IBU MENGONSUMSI TABLET BESI-FOLAT SELAMA KEHAMILAN

Directory of Open Access Journals (Sweden)

Luh Ade Ari Wiradnyani

2013-11-01

Full Text Available ABSTRACTThis review aims at compiling and summarizing findings of published studies that assessed factors associated with compliance of women to take recommended iron tablets during pregnancy. The review is done in 10 published studies (8 are 2002—2010 publications and 2 are 1993—1994 publications indexed in Pubmed with the above objective. Low utilization of antenatal care/ANC services is found to be associated with low compliance as it prevents the women to receive recommended number of the iron tablets as well as decrease the opportunity of women to have encouragement from health staff to take the tablets. Supply of tablets becomes the issue since not all women receiving 30 tablets/ANC visits as recommended. Studies on influence of side-effects of taking the tablets to compliance show inconclusive findings. Some studies found the effect is very minimal, and can be managed appropriately especially among more educated women and among women with adequate counseling. Studies also indicated that support from family is important to reduce possibility of pregnant women forgot to take the tablets, the other major factor of the low compliance. Quality of counseling, e.g. clarity of the messages, is associated with compliance. In conclusion, improving support from ANC provider (such as sufficient tablet supply, clear message on the tablets benefits and support from family may contribute to better compliance of women towards maternal iron supplementation.Keywords: compliance, iron supplementation, pregnancyABSTRAKReview ini bertujuan mengumpulkan temuan studi yang mengukur faktor yang berhubungan dengan kepatuhan ibu dalam mengonsumsi tablet besi selama kehamilan. Review dilakukan pada 10 studi (8 publikasi tahun 2002—2010, 2 publikasi tahun 1993—1994 yang terdaftar di Pubmed. Rendahnya partisipasi ibu hamil untuk memeriksakan kehamilannya/ANC berhubungan dengan rendahnya kepatuhan konsumsi tablet besi. Rendahnya kunjungan ANC membuat ibu tidak

Formulation of Sustained-Release Diltiazem Matrix Tablets Using ...

African Journals Online (AJOL)

Formulation of Sustained-Release Diltiazem Matrix Tablets Using Hydrophilic Gum Blends. A Moin, H.G Shivakumar. Abstract. Purpose: To develop sustained release matrix tablets of diltiazem hydrochloride (DTZ) using karaya gum (K) alone or in combination with locust bean gum (LB) and hydroxypropyl methylcellulose ...

The possession of brochures on emergency and of iodide tablets by households

International Nuclear Information System (INIS)

Hultaaker, Oe.

1985-01-01

People who live within twelve to fifteen kilometers from one of the Swedish Nuclear Power plants have received a brochure about existing security arrangements and the actions which they are recommended to take in the wake of a nuclear accident. Tablets containing potassium iodide have also been handed out to the people living close to the power plants. Due to the short life of the iodide tablets, people receive new ones from time to time. Before the distribution of new tablets, however, the National Institute of Radiation Protection wanted to learn if people still had the old tablets and the brochure in their homes. The National Institute of Radiation Protection also was interested in assessing people's knowledge about the protection given by the iodide tablets and whether people knew when to take them. Nine persons out of ten (87%) could show the tablets to the interviewers, and seven out of ten (71%) could do so with the brochure. Half of the total number of respondents knew when they were supposed to take the tablets (47%). Nevertheless two partly conflicting messages have been given to the public about the proper time to take the tablet: according to the text printed on the cover of the tablets, they are to be taken immediately when the people have learnt about an accident; but according to the brochure distributed to the households, people must wait until they are told by the radio to take the tablets. One person of four (22%) said that the radio should inform them, and almost the same number of people (25%) said that the tablets ought to be taken immediately following an accident. Only one person of four (27%) knew what protection they would get from the iodine tablets. Another 17% had a vague idea about the affect resulting from taking them. Many people (25%) had the false belief that the tablets offered them general protection against radiation. (author)

Fast disintegrating tablets: Opportunity in drug delivery system

Directory of Open Access Journals (Sweden)

Ved Parkash

2011-01-01

Full Text Available Fast disintegrating tablets (FDTs have received ever-increasing demand during the last decade, and the field has become a rapidly growing area in the pharmaceutical industry. Oral drug delivery remains the preferred route for administration of various drugs. Recent developments in the technology have prompted scientists to develop FDTs with improved patient compliance and convenience. Upon introduction into the mouth, these tablets dissolve or disintegrate in the mouth in the absence of additional water for easy administration of active pharmaceutical ingredients. The popularity and usefulness of the formulation resulted in development of several FDT technologies. FDTs are solid unit dosage forms, which disintegrate or dissolve rapidly in the mouth without chewing and water. FDTs or orally disintegrating tablets provide an advantage particularly for pediatric and geriatric populations who have difficulty in swallowing conventional tablets and capsules. This review describes various formulations and technologies developed to achieve fast dissolution/dispersion of tablets in the oral cavity. In particular, this review describes in detail FDT technologies based on lyophilization, molding, sublimation, and compaction, as well as approaches to enhancing the FDT properties, such as spray drying and use of disintegrants. In addition, taste-masking technologies, experimental measurements of disintegration times, and dissolution are also discussed.

Disintegration of chemotherapy tablets for oral administration in patients with swallowing difficulties.

Science.gov (United States)

Siden, Rivka; Wolf, Matthew

2013-06-01

The administration of oral chemotherapeutic drugs can be problematic in patients with swallowing difficulties. Inability to swallow solid dosage forms can compromise compliance and may lead to poor clinical outcome. The current technique of tablet crushing to aid in administration is considered an unsafe practice. By developing a technique to disintegrate tablets in an oral syringe, the risk associated with tablet crushing can be avoided. The purpose of this study was to determine the feasibility of using disintegration in an oral syringe for the administration of oral chemotherapeutic tablets. Eight commonly used oral chemotherapeutic drugs were tested. Tablets were placed in an oral syringe and allowed to disintegrate in tap water. Various volumes and temperatures were tested to identify which combination allows for complete disintegration of the tablet in the shortest amount of time. The oral syringe disintegration method was considered feasible if disintegration occurred in ≤15 min and in ≤20 mL of water and the dispersion passed through an oral syringe tip. The following tablets were shown to disintegrate within 15 min and in disintegration test. Disintegrating oral chemotherapeutic tablets in a syringe provides a closed system to administer hazardous drugs and allows for the safe administration of oral chemotherapeutic drugs in a tablet form to patients with swallowing difficulties.

Bioequivalence of two film-coated tablets of imatinib mesylate 400 mg: a randomized, open-label, single-dose, fasting, two-period, two-sequence crossover comparison in healthy male South American volunteers.

Science.gov (United States)

Parrillo-Campiglia, Susana; Ercoli, Mónica Cedres; Umpierrez, Ofelia; Rodríguez, Patricia; Márquez, Sara; Guarneri, Carolina; Estevez-Parrillo, Francisco T; Laurenz, Marilena; Estevez-Carrizo, Francisco E

2009-10-01

Imatinib is a tyrosine kinase inhibitor that has been established as a highly effective therapy for chronic myelogenous leukemia and gastrointestinal stromal tumors. A new generic, once-daily 400-mg tablet of imatinib has been developed by a pharmaceutical company in Argentina, where the regulatory standard for marketing authorization of an imatinib generic is in vitro dissolution testing. The aim of this study was to assess the bioequivalence of a new generic film-coated test tablet formulation versus a film-coated reference tablet formulation of imatinib 400 mg. The local manufacturer seeks to validate the in vitro performance of this new formulation with a bioequivalence study. A randomized, open-label, single-dose, fasting, 2-period, 2-sequence crossover design with a 2-week washout period was used in this study. The study population consisted of healthy male South American (Uruguayan) volunteers, who were assigned in a 1:1 ratio to a randomized sequence (test-reference or reference-test). In each period, the test or reference formulation was administered after an overnight fast. During the 72-hour follow-up period, participants were monitored for vital signs and symptoms. Blood samples were collected at 15 time points, including baseline, until 72 hours. Physical examination and laboratory tests (blood, urine) were repeated 1 week after study completion. A noncompartmental model was used to determine the pharmacokinetic parameters of imatinib. The 90% CIs of the test/reference ratios for AUC(0-infinity) and C(max) were determined; the test and reference formulations were considered bioequivalent if the 90% CIs were between 0.80 and 1.25. Adverse events were assessed by a nurse who administered a questionnaire while the healthy volunteers were admitted in the unit. The bioequivalence study was conducted in 30 Uruguayan male volunteers. Demographic characteristics (mean [SD]) included age, 27.8 (6.5) years; weight, 71.2 (9.8) kg; height, 1.71 (0.09) m; and body

On the symbolism of the white coat.

Science.gov (United States)

Nash, David A

2014-12-01

The white coat ceremony has become an academic ritual in the health professions: a ceremony that signals a transformation of status from ordinary student to that of one studying to become a health professional. While donning the white coat is a sign of a changed role, the white coat is also a powerful symbol of transformation. White is a symbol of purity, and the white coat symbolizes the purity of purpose being affirmed in becoming a health professional. Dentistry is afforded the status of a learned profession as a result of the power dentists possess over patients seeking care; this power is based in sophisticated knowledge. Patients must trust that the dentist's knowledge and skills will be used in their best interest-always to benefit, never to exploit. The white coat symbolizes an affirmation on the part of aspiring dentists that their purpose will be pure and that they can be trusted to honor the tradition of the learned professions in placing the interest of patients above self. Absent an emphasis on the symbolic nature of the white coat ceremony, it can simply become an opportunity to publicly congratulate individuals for their success in gaining entrance to the study of dentistry. By understanding its significance, however, the white coat ceremony can serve as a powerful, meaningful ritual emphasizing the transformation occurring within an individual who is entering the profession of dentistry.

Portable Tablets in Science Museum Learning: Options and Obstacles

Science.gov (United States)

Gronemann, Sigurd Trolle

2017-06-01

Despite the increasing use of portable tablets in learning, their impact has received little attention in research. In five different projects, this media-ethnographic and design-based analysis of the use of portable tablets as a learning resource in science museums investigates how young people's learning with portable tablets matches the intentions of the museums. By applying media and information literacy (MIL) components as analytical dimensions, a pattern of discrepancies between young people's expectations, their actual learning and the museums' approaches to framing such learning is identified. It is argued that, paradoxically, museums' decisions to innovate by introducing new technologies, such as portable tablets, and new pedagogies to support them conflict with many young people's traditional ideas of museums and learning. The assessment of the implications of museums' integration of portable tablets indicates that in making pedagogical transformations to accommodate new technologies, museums risk opposing didactic intention if pedagogies do not sufficiently attend to young learners' systemic expectations to learning and to their expectations to the digital experience influenced by their leisure use.

The Women at work in the Linear B Tablets

DEFF Research Database (Denmark)

Nosch, Marie-Louise Bech

2003-01-01

The article investigates the role of women in Mycenaean society according to the Linear B tablets......The article investigates the role of women in Mycenaean society according to the Linear B tablets...

Tablet-Based Education to Reduce Depression-Related Stigma

Science.gov (United States)

Lu, Catherine; Winkelman, Megan; Wong, Shane Shucheng

2016-01-01

Objectives: This study investigated the efficacy of a tablet-based multimedia education application, the Project Not Alone Depression Module, in improving depression literacy and reducing depression stigma among a community-based mental health clinic population. Methods: A total of 93 participants completed either a tablet-based multimedia…

The rationale of scored tablets as dosage form.

NARCIS (Netherlands)

Rodenhuis, N.; Smet, P.A.G.M. de; Barends, D.M.

2004-01-01

The aim of the study was to get insight into the rationale of scored tablets. This was pursued by studying patient's reasons for subdividing ("breaking") scored and unscored tablets. Patients who picked up their prescriptions in 5 community pharmacies in The Netherlands were questioned. Two-hundred

Formulation of Fast-Dissolving Tablets of Promethazine Theoclate ...

African Journals Online (AJOL)

Purpose: To optimize and formulate promethazine theoclate fast-dissolving tablets that offer a suitable approach to the treatment of nausea and vomiting. Method: The solubility of promethazine theoclate was increased by formulating it as a fast-dissolving tablet containing β-cyclodextrin, crospovidone, and camphor, using ...

Preparation and biological efficacy of haddock bone calcium tablets

Science.gov (United States)

Huo, Jiancong; Deng, Shanggui; Xie, Chao; Tong, Guozhong

2010-03-01

To investigate the possible use of waste products obtained after processing haddock, the present study prepared haddock bone calcium powder by NaOH and ethanol soaking (alkalinealcohol method) and prepared haddock bone calcium tablets using the powder in combination with appropriate excipients. The biological efficacy of the haddock bone calcium tablets was investigated using Wistar rats as an experiment model. Results show that the optimal parameters for the alkalinealcohol method are: NaOH concentration 1 mol/L, immersion time 30 h; ethanol concentration 60%, immersion time 15 h. A mixture of 2% polyvinylpyrrolidone in ethanol was used as an excipient at a ratio of 1:2 to full-cream milk powder, without the use of a disintegrating agent. This process provided satisfactory tablets in terms of rigidity and taste. Animal studies showed that the haddock bone calcium tablets at a dose of 2 g·kg-1·d-1 or 5g·kg-1·d-1 significantly increased blood calcium and phosphorus levels and bone calcium content in rats. Therefore, these tablets could be used for calcium supplementation and prevent osteoporosis. Although the reasons of high absorption in the rats fed with haddock bone calcium tablets are unclear, it is suggested that there are some factors, such as treatment with method of alkaline-alcohol or the added milk, may play positive roles in increasing absorption ratio.

Penggunaan Tablet di Binus Online Learning

OpenAIRE

Agus Putranto; Wawan Saputra

2014-01-01

Utilization of e-learning can improve learning effectiveness and flexibility. Features of e-learning that are important in teaching and learning activities are tasks features, discussion forums and discussion face to face in a video conference. BINUS Online Learning is a program that offers students to conduct online lectures. Online BINUS need to think about software and hardware that must be provided in a tablet. Therefore, this study will analyze the use of the tablet which will be used fo...

Security Approaches in Using Tablet Computers for Primary Data Collection in Clinical Research

OpenAIRE

Wilcox, Adam B.; Gallagher, Kathleen; Bakken, Suzanne

2013-01-01

Next-generation tablets (iPads and Android tablets) may potentially improve the collection and management of clinical research data. The widespread adoption of tablets, coupled with decreased software and hardware costs, has led to increased consideration of tablets for primary research data collection. When using tablets for the Washington Heights/Inwood Infrastructure for Comparative Effectiveness Research (WICER) project, we found that the devices give rise to inherent security issues asso...

Accuracy of tablet splitting and liquid measurements: an examination of who, what and how.

Science.gov (United States)

Abu-Geras, Dana; Hadziomerovic, Dunja; Leau, Andrew; Khan, Ramzan Nazim; Gudka, Sajni; Locher, Cornelia; Razaghikashani, Maryam; Lim, Lee Yong

2017-05-01

To examine factors that might affect the ability of patients to accurately halve tablets or measure a 5-ml liquid dose. Eighty-eight participants split four different placebo tablets by hand and using a tablet splitter, while 85 participants measured 5 ml of water, 0.5% methylcellulose (MC) and 1% MC using a syringe and dosing cup. Accuracy of manipulation was determined by mass measurements. The general population was less able than pharmacy students to break tablets into equal parts, although age, gender and prior experience were insignificant factors. Greater accuracy of tablet halving was observed with tablet splitter, with scored tablets split more equally than unscored tablets. Tablet size did not affect the accuracy of splitting. However, >25% of small scored tablets failed to be split by hand, and 41% of large unscored tablets were split into >2 portions in the tablet splitter. In liquid measurement, the syringe provided more accurate volume measurements than the dosing cup, with higher accuracy observed for the more viscous MC solutions than water. Formulation characteristics and manipulation technique have greater influences on the accuracy of medication modification and should be considered in off-label drug use in vulnerable populations. © 2016 Royal Pharmaceutical Society.

Effect Of Oligomeric Enteral Nutrition On Symptoms Of Acute Radiation Enteritis

International Nuclear Information System (INIS)

Dubinsky, P.

2008-01-01

Radiotherapy of abdominal and pelvic tumours is frequently associated with acute radiation enteritis. Predominant symptoms include diarrhea, watery stools, abdominal pain, nausea and vomiting. There are very few effective interventions available for this condition. Enteral oligomeric nutrition has been used in bowel diseases with functional failure similar to radiation enteritis. The aim of presented work was to observe occurrence of symptoms of radiation enteritis in patients undergoing abdominal or pelvic radiotherapy. Apart from diet and pharmacological therapy, oral oligomeric enteral nutrition (Peptisorb Powder Nutricia) at the dose of 1000 - 2000 ml per day was administered for minimum of 4 days. Planned period of administration was 14 days and longer. Symptoms of radiation enteritis were evaluated at the beginning and in the end of administration. Prevalence of all evaluated symptoms of radiation enteritis was decreased and difference was statistically significant for diarrhea, watery stools, abdominal pain, nausea and vomiting. The use of evaluated oligomeric nutritional support might, in conjunction with pharmacotherapy and diet, alleviate symptoms of acute radiation enteritis and maintain nutritional status of patients. (author)

Use of tablets for instruction and learning in microbiology labs

DEFF Research Database (Denmark)

Møller, Karen Louise; Jelsbak, Vibe Alopaeus; Georgsen, Marianne

of this project are to develop a technological infrastructure to support students’ work in the lab and to develop teaching and learning resources. Our research question is: How is teaching and learning in the laboratory influenced by the tablets and the following multimodal teaching and learning materials...... and taken notes by hand. Use of tablets in the lab offers new opportunities. In September 2012, nine tablets were introduced into one of the labs of the college. Groups of students use the tablets to access documents, watch video instructions, and to document results and procedures digitally. The objectives......? The empirical part of the project has been documented through field observations in the lab (in writing and with photos). We have found the following to be characteristic of the work of the students: the students use the tablets collaboratively, take more photos than requested, use the video based instructions...

Effect of gel formation on the dissolution behavior of clarithromycin tablets.

Science.gov (United States)

Inukai, Koki; Takiyama, Kei; Noguchi, Shuji; Iwao, Yasunori; Itai, Shigeru

2017-04-15

Clarithromycin (CAM) is a macrolide antibiotic that is widely used at clinical sites. We found that release of CAM is suppressed when tablets of CAM were exposed to an external solvent containing carboxylate buffers such as citrate. The suppressed release of CAM can be attributed to the formation of gels on the tablet surfaces, which inhibits penetration of the solvent into the tablet and thus disintegration of the tablets. Delayed disintegration of the tablets was also observed for commercial tablets. This suggests that taking CAM and carboxylates at the same time might be avoided. The crystal structure of CAM citrate reveals that molecular chains of CAM are cross-linked by hydrogen bond between citrate groups in the crystal. The crystal structure indicates that cross-linked CAM chains of the three-dimensional mesh structure might also be formed in high concentration CAM solutions in the presence of carboxylates, resulting in gel formation. Copyright © 2017 Elsevier B.V. All rights reserved.

Keep taking the tablets? Assessing the use of tablet devices in learning and teaching activities in the Further Education sector

Directory of Open Access Journals (Sweden)

Khristin Fabian

2014-02-01

Full Text Available This article summarises the methodology and outcomes of an interventionist/action research project to assess the benefits, and potential pitfalls, of the use of mobile devices in learning and teaching activities in a Further Education environment. A bank of 15 tablet devices were purchased and prepared for classroom use. Staff members were approached to scope potential activities and uses for the tablet devices. Three departments took part in the research activity: the Language School, Social and Vocational Studies and the Hairdressing department. Use of the tablets was varied in nature and included: use of multimedia tools, use of apps, creation and use of a bespoke app, multimedia manipulation and sharing, and creation of an online e-portfolio. Staff and student feedback was gathered during and after the project, and project authors were present during classroom activities for observation and recording purposes. Overall feedback was very positive, but there were issues with tablet use and administration. One of the major issues was the onerous nature of the security setup, and app administration.

Characterising the disintegration properties of tablets in opaque media using texture analysis

OpenAIRE

Scheuerle, Rebekah L.; Gerrard, Stephen E.; Kendall, Richard A.; Tuleu, Catherine; Slater, Nigel K.H.; Mahbubani, Krishnaa T.

2015-01-01

Tablet disintegration characterisation is used in pharmaceutical research, development, and quality control. Standard methods used to characterise tablet disintegration are often dependent on visual observation in measurement of disintegration times. This presents a challenge for disintegration studies of tablets in opaque, physiologically relevant media that could be useful for tablet formulation optimisation. In this study is explored an application of texture analysis disintegration testin...

Tablet computers to support outpatient pulmonary rehabilitation in patients with COPD

DEFF Research Database (Denmark)

Ringbaek, Thomas J.; Lavesen, Marie; Lange, Peter

2016-01-01

BACKGROUND: A minicomputer (tablet) with instructions and a training diary has the potential of facilitating adherence to pulmonary rehabilitation (PR). OBJECTIVE: To evaluate the effect of adding a tablet to a classic outpatient PR programme for COPD patients. METHODS: A total of 115 patients...... participated in a 7- to 10-week outpatient PR programme in groups of 10-12 individuals. Half of the groups were assigned to PR plus a tablet (tablet group) and the other groups were assigned to PR only (controls). Primary effect parameters were endurance shuttle walk time (ESWT) and disease-specific health...... status (COPD Assessment Test=CAT). RESULTS: The change in ESWT was significantly better in the control group (mean 167 sec) compared with the tablet group (mean 51 sec) (p

Resveratrol cocrystals with enhanced solubility and tabletability.

Science.gov (United States)

Zhou, Zhengzheng; Li, Wanying; Sun, Wei-Jhe; Lu, Tongbu; Tong, Henry H Y; Sun, Changquan Calvin; Zheng, Ying

2016-07-25

Two new 1:1 cocrystals of resveratrol (RES) with 4-aminobenzamide (RES-4ABZ) and isoniazid (RES-ISN) were synthesized by liquid assisted grinding (LAG) and rapid solvent removal (RSR) methods using ethanol as solvent. Their physiochemical properties were characterized using PXRD, DSC, solid state and solution NMR, FT-IR, and HPLC. Pharmaceutically relevant properties, including tabletability, solubility, intrinsic dissolution rate, and hygroscopicity, were evaluated. Temperature-composition phase diagram for RES-ISN cocrystal system was constructed from DSC data. Both cocrystals show higher solubility than resveratrol over a broad range of pH. They are phase stable and non-hygroscopic even under high humidity conditions. Importantly, both cocrystals exhibit improved solubility and tabletability compared with RES, which make them more suitable candidates for tablet formulation development. Copyright © 2016 Elsevier B.V. All rights reserved.

Compressional, mechanical and release properties of a novel gum in paracetamol tablet formulations

Directory of Open Access Journals (Sweden)

Adedokun Musiliu O.

2014-09-01

Full Text Available The binding properties of Eucalyptus gum obtained from the incised trunk of Eucalyptus tereticornis, were evaluated in paracetamol tablet formulations, in comparison with that of Gelatin B.P. In so doing, the compression properties were analyzed using density measurements and the compression equations of Heckel, Kawakita and Gurham. In our work, the mechanical properties of the tablets were assessed using the crushing strength and friability of the tablets, while the drug release properties of the tablets were assessed using disintegration and dissolution times. The results of the study reveal that tablet formulations incorporating Eucalyptus gum as binder, exhibited faster onset and higher amount of plastic deformation during compression than those containing gelatin. What is more, the Gurnham equation could be used as a substitute for the Kawakita equation in describing the compression properties of pharmaceutical tablets. Furthermore, the crushing strength, disintegration and dissolution times of the tablets increased with binder concentration, while friability values decreased. We noted that no significant differences in properties exist between formulations derived from the two binders (p > 0.05 exist. While tablets incorporating gelatin exhibited higher values for mechanical properties, Eucalyptus gum tablets had better balance between mechanical and release properties - as seen from the CSFR/Dt values. Tablets of good mechanical and release properties were prepared using Eucalyptus gum as a binder, and, therefore, it could serve as an alternative binder in producing tablets with good mechanical strength and fast drug release.

Evaluation of disintegration and dissolution of chloroquine tablets in ...

African Journals Online (AJOL)

Evaluation of disintegration and dissolution of chloroquine tablets in some States in Northern Nigeria. ... This study seeks to assess the quality of chloroquine tablets in some States in Northern Nigeria by determining ... HOW TO USE AJOL.

Determination of Letrozole in Tablet Formulations by Reversed ...

African Journals Online (AJOL)

Determination of Letrozole in Tablet Formulations by Reversed Phase High Performance Liquid Chromatography. ... The assay values for the two branded letrozole tablets tested were 99.2 and 100.2 %, respectively with % relative standard deviation (RSD) of 0.781 and 0.568, respectively. The bench top stability data of the ...

Optimization and Formulation of Orodispersible Tablets of Meloxicam

African Journals Online (AJOL)

... 98.5% and fast drug release rate of 99.5% within 30 min, as compared with the conventional tablet (49.5%) . Conclusion: It is feasible to formulate orodispersible tablets of meloxican with acceptable disintegration time, rapid drug release and good hardness, which could be amenable to replication on an industrial scale.

An Exploratory Study Investigating How and Why Managers Use Tablets to Support Managerial Decision-Making

Directory of Open Access Journals (Sweden)

Meng Xiao

2017-11-01

Full Text Available Managers are often mobile and a large proportion of their work is dealing with decisions. Although many managers currently use tablet computers in their work, there is little research on the use of tablets for managerial decision-support. This exploratory study aims to investigate the ways in which managers use tablets to support their decision-making and the reasons why they do so. Using Task-Technology Fit theory, semi-structured interviews were conducted with 20 managers, 17 of whom used tablets for their work-related decision-making. The study reveals managers’ tablet usage patterns in terms of location, tablet applications, decision activities and types. This study has also found that a range of tablet characteristics and decision-task characteristics affect managers’ use of tablets to support decision-making at work. This exploratory study contributes to both academia and industry by providing evidence on the tablet decision-support area, and affording organisations, tablet vendors and tablet application developers informative findings for further improvement in the provision of tablet-based decision support.

Tablet computers for recording tuberculosis data at a community ...

African Journals Online (AJOL)

Tablet computers for recording tuberculosis data at a community health centre in King Sabata Dalindyebo Local Municipality, ... South African Family Practice ... They expressed a desire to extend the use of tablets to other areas of their work.

Evaluation of Multiple Linear Regression-Based Limited Sampling Strategies for Enteric-Coated Mycophenolate Sodium in Adult Kidney Transplant Recipients.

Science.gov (United States)

Brooks, Emily K; Tett, Susan E; Isbel, Nicole M; McWhinney, Brett; Staatz, Christine E

2018-04-01

Although multiple linear regression-based limited sampling strategies (LSSs) have been published for enteric-coated mycophenolate sodium, none have been evaluated for the prediction of subsequent mycophenolic acid (MPA) exposure. This study aimed to examine the predictive performance of the published LSS for the estimation of future MPA area under the concentration-time curve from 0 to 12 hours (AUC0-12) in renal transplant recipients. Total MPA plasma concentrations were measured in 20 adult renal transplant patients on 2 occasions a week apart. All subjects received concomitant tacrolimus and were approximately 1 month after transplant. Samples were taken at 0, 0.33, 0.5, 1, 1.5, 2, 2.5, 3, 3.5, 4, 6, and 8 hours and 0, 0.25, 0.5, 0.75, 1, 1.25, 1.5, 2, 3, 4, 6, 9, and 12 hours after dose on the first and second sampling occasion, respectively. Predicted MPA AUC0-12 was calculated using 19 published LSSs and data from the first or second sampling occasion for each patient and compared with the second occasion full MPA AUC0-12 calculated using the linear trapezoidal rule. Bias (median percentage prediction error) and imprecision (median absolute prediction error) were determined. Median percentage prediction error and median absolute prediction error for the prediction of full MPA AUC0-12 were multiple linear regression-based LSS was not possible without concentrations up to at least 8 hours after the dose.

Enhancing the Classroom Experience: Instructor Use of Tablets

Science.gov (United States)

Cummings, Jeff; Hill, Stephen

2015-01-01

Instructors continually search for innovative approaches to interact with and engage students in the classroom. The tablet offers a potential innovation for this purpose. Tablet devices from Apple, Microsoft, and other hardware vendors have overcome many of the challenges of the past (e.g. cost and limited applications) to become useful tools for…

Equivalency of Paper versus Tablet Computer Survey Data

Science.gov (United States)

Ravert, Russell D.; Gomez-Scott, Jessica; Donnellan, M. Brent

2015-01-01

Survey responses collected via paper surveys and computer tablets were compared to test for differences between those methods of obtaining self-report data. College students (N = 258) were recruited in public campus locations and invited to complete identical surveys on either paper or iPad tablet. Only minor homogeneity differences were found…

Development of natural gum based fast disintegrating tablets of glipizide

OpenAIRE

Antesh Kumar Jha; Dipak Chetia

2012-01-01

Dysphagia and risk of choking are leading causes of patient non-compliance in the self-administration of conventional tablets. To overcome these limitations of conventional tablets fast-disintegrating tablets were developed, using natural gums. Natural gums were evaluated for bulk swelling capacity. Powder mix containing natural gums and glipizide was evaluated for water sorption, swelling index and capillary action. For faster onset and immediate hypoglycemic action, the fast disintegrating ...

Evaluation of matrix type mucoadhesive tablets containing indomethacin for buccal application.

Science.gov (United States)

Ikeuchi-Takahashi, Yuri; Sasatsu, Masanaho; Onishi, Hiraku

2013-09-10

Nonsteroidal anti-inflammatory drugs (NSAIDs) are administered for pain relief from oral mucositis. However, the systemic administration of NSAIDs is limited due to systemic side effects. To avoid these side effects and treat local lesions effectively, a matrix type mucoadhesive tablet was developed. A mixture of hard fat, ethylcellulose (EC) and polyethylene glycol (PEG) was used as a matrix base, and indomethacin (IMC) was used as the principal agent. In tablets consisting of hard fat, EC and IMC, the drug release was sustained. In tablets consisting of hard fat, EC, considerable amounts of PEG and IMC, the drug release was relatively increased and IMC existed as the molecular phase or in an amorphous state. The in vitro adhesive force of the tablets consisting of hard fat, EC, considerable amounts of PEG and IMC was significantly increased as compared with the tablets consisting of hard fat and IMC. A significantly high tissue concentration and significantly low plasma concentration were observed after buccal administration of this matrix type mucoadhesive tablet as compared with that after oral administration of IMC. Thus, the matrix type mucoadhesive tablet has good potential as a preparation for the treatment of pain due to oral aphtha. Copyright © 2013 Elsevier B.V. All rights reserved.

The Nebusarsekim Tablet

NARCIS (Netherlands)

Stadhouders, H.A.I.

2008-01-01

During the summer of 2007 an internet hype was unleashed by the breaking news that an Old Testament name of some importance, figuring in the Book of Jeremiah Ch. 39, had been positively identified on a cuneiform clay tablet, viz. a bill of receipt from the time of this prophet's floruit. Many a

Three-Year Outcomes in Kidney Transplant Patients Randomized to Steroid-Free Immunosuppression or Steroid Withdrawal, with Enteric-Coated Mycophenolate Sodium and Cyclosporine: The Infinity Study

Directory of Open Access Journals (Sweden)

A. Thierry

2014-01-01

Full Text Available In a six-month, multicenter, open-label trial, de novo kidney transplant recipients at low immunological risk were randomized to steroid avoidance or steroid withdrawal with IL-2 receptor antibody (IL-2RA induction, enteric-coated mycophenolate sodium (EC-MPS: 2160 mg/day to week 6, 1440 mg/day thereafter, and cyclosporine. Results from a 30-month observational follow-up study are presented. Of 166 patients who completed the core study on treatment, 131 entered the follow-up study (70 steroid avoidance, 61 steroid withdrawal. The primary efficacy endpoint of treatment failure (clinical biopsy-proven acute rejection (BPAR graft loss, death, or loss to follow-up occurred in 21.4% (95% CI 11.8–31.0% of steroid avoidance patients and 16.4% (95% CI 7.1–25.7% of steroid withdrawal patients by month 36 (P=0.46. BPAR had occurred in 20.0% and 11.5%, respectively (P=0.19. The incidence of adverse events with a suspected relation to steroids during months 6–36 was 22.9% versus 37.1% (P=0.062. By month 36, 32.4% and 51.7% of patients in the steroid avoidance and steroid withdrawal groups, respectively, were receiving oral steroids. In conclusion, IL-2RA induction with early intensified EC-MPS dosing and CNI therapy in de novo kidney transplant patients at low immunological risk may achieve similar three-year efficacy regardless of whether oral steroids are withheld for at least three months.

Security approaches in using tablet computers for primary data collection in clinical research.

Science.gov (United States)

Wilcox, Adam B; Gallagher, Kathleen; Bakken, Suzanne

2013-01-01

Next-generation tablets (iPads and Android tablets) may potentially improve the collection and management of clinical research data. The widespread adoption of tablets, coupled with decreased software and hardware costs, has led to increased consideration of tablets for primary research data collection. When using tablets for the Washington Heights/Inwood Infrastructure for Comparative Effectiveness Research (WICER) project, we found that the devices give rise to inherent security issues associated with the potential use of cloud-based data storage approaches. This paper identifies and describes major security considerations for primary data collection with tablets; proposes a set of architectural strategies for implementing data collection forms with tablet computers; and discusses the security, cost, and workflow of each strategy. The paper briefly reviews the strategies with respect to their implementation for three primary data collection activities for the WICER project.

Immunological comparison of allergen immunotherapy tablet treatment and subcutaneous immunotherapy against grass allergy

DEFF Research Database (Denmark)

Aasbjerg, K; Backer, V; Lund, G

2014-01-01

BACKGROUND: IgE-mediated allergic rhinitis to grass pollen can successfully be treated with either allergen immunotherapy tablets (SLIT tablet) or SQ-standardized subcutaneous immunotherapy (SCIT). The efficacy of these two treatment modalities for grass allergy is comparable, but the immunological...... mechanisms may differ. ClinicalTrials.gov ID: NCT01889875. OBJECTIVES: To compare the immunological changes induced by SQ-standardized SCIT and SLIT tablet. METHODS: We randomized 40 individuals with grass pollen rhinitis into groups receiving SCIT, SLIT tablet, or neither and followed them for 15 months...... differed significantly in both SCIT and SLIT-tablet treatment groups when compared to the control group. Both SCIT and SLIT-tablet groups were significantly different from the control group after 1–3 months of treatment. In general, the changes induced by SCIT reached twice that of SLIT tablet...

Solid-state properties and dissolution behaviour of tablets containing co-amorphous indomethacin-arginine

DEFF Research Database (Denmark)

Lenz, Elisabeth; Jensen, Katrine Birgitte Tarp; Blaabjerg, Lasse Ingerslev

2015-01-01