WorldWideScience

Sample records for system donyu shien

  1. Research program for environmentally-friendly coal utilization system. Follow-up project for simplified desulfurizers (Weifang Chemical Industry Works); Kankyo chowagata sekitan riyo system donyu shien jigyo. Kan`i datsuryu setsubi ni kakawaru follow up jigyo (Weifang kakosho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To suppress the emission of environmental pollutants from coal utilization in China and to contribute to stable security of Japan`s energy, demonstration of clean coal technology and consolidation of diffusion base to be introduced into China have been promoted. Demonstration program for diffusing simplified desulfurizers has been promoted. For accelerating the achievement, experts of desulfurizers were delegated to Weifang Chemical Industry Works, to support the program. Exhaust gas is introduced from boiler via water spray dust remover, suction fan and centralized stack into absorption tower of the simplified wet-type desulfurizer. In the ascending process, the exhaust gas contacts with absorbent, to remove SO2 and dust. The absorbent is blasted up through the spray nozzle. The absorbent is oxidized by the air into sulfate ion in the liquid chamber at the lower part of tower, and neutralized by hydrated lime to form gypsum. Through the continuous operation for two years, understandings were remarkably increased. However, good treatment of the tax system is required for further diffusion. Though there are no problems for ordinary start and stop, emergency operation is insufficient. There are some problems in the maintenance due to the delay of finding failures. 16 figs., 1 tab.

  2. Report on achievements in proliferation project to assist introduction of environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998 (recovering facilities); Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo. 1998 nendo CMG kaishu riyo system kyodo system kyodo jissho jigyo (kaishu setsubi)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This paper describes the achievements of the discussions in fiscal 1998 on the recovering system for coal bed methane gas to be supplied to the city of Tieling in China. The paper puts on record the associated documents, and figures and drawings. The associated documents appearing in the paper include the table for explosion-proof examination on the recovering devices, a parts list for the RK-3A type test drilling machine, and its operation manual. Specifications for the test drilling machine (including those for the sealing pumps), specifications for the mouth facilities, and device lists are shown. Test drilling device arrangement drawings and standard drilling record table are also described. Central blower specifications, a back-fire preventing device, a device to prevent well exterior from freezing, and a summarized drawing for drain remover for gas induction for the Daixing mine are explained. The schemes for induction and sealing, specifications and procedures for observation devices are shown. Specifications for sealing materials and the centralized monitoring facilities are also touched on. The safety measures, measures taken for power failure in the centralized monitoring facilities, and the control organization are described. Test drilling cost simulation and environment assessing methods are also described. The figures and drawings presented include the topographic map, Daixing mine cavity drawing, pipeline network, and chart for representative test drilling columns near the coal beds were also presented. (NEDO)

  3. Fiscal 2000 project on measures for assisting and diffusing environmentally-friendly coal utilization system introduction. CMG recovery/utilization system joint demonstration project; 2000 nendo kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo chosa hokoku. CMG kaishu riyo system kyodo jissho jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A CMG (coal mine gas) recovery/utilization system was designed, constructed, and then demonstrated at a model coal mining district in Liaoning Province for the purpose of contributing to the solution of energy and environment related problems in China. The recovery system demonstration test, aiming to improve on safety and productivity of coal mining and to supply recovered gas with stability, involved gas drainage test boring, mine sealing, sealed gas induction control, centralized gas monitoring, etc., which were carried out at the coal mine working face. A utilization system demonstration test was conducted, and CMG would continue to be supplied to the current users and CMG utilization would be started at the other 6 coal mines. For the supply of CMG to large-scale gas consuming areas, steel materials were manufactured and processed for spherical gas holders and denitrification facilities, gas holders were constructed, pipe lines were installed, and a provisional gas supply was carried out. For the transfer and diffusion of the technology, Chinese engineers were trained in Japan and Japanese engineers were dispatched to China. (NEDO)

  4. Report on achievements in proliferation project to assist introduction of environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998 (utilization facilities); Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo seika hokokusho. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo (riyo setsubi)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This paper describes the achievements of the discussions in fiscal 1998 on the utilization facilities related to the coal bed methane gas supply plan for the city of Tieling in China. The gas quality standard calls for 3,500 kcal/m{sup 3} or more (methane concentration of 41% or higher). The supply is planned to start in December 1999, and continue the supply of 141,000 Nm{sup 3}/day in 2000, and 212,000 Nm{sup 3}/day in 2001 and thereafter. A gas supply center to collect gases recovered from each mine will be installed in the vicinity of the existing gas holder located about 2 km east of the Tiefa Mining Bureau. The Japanese side bears the cost of installing a gas compression and transportation facility for gas supply to the city of Tieling, a monitoring system, and devices for comprehensive surveillance system. This paper shows the overall plan drawings, the drain separator room building plan, the plans for arranging devices in the machine room, and the piping scheme. In addition, the piping plan around the gas holder, and the basic device plan are shown. Also appearing in the paper are the machine summary drawings, summarized flow charts, gas holder plan, de-humidifier plan, and electricity and instrumentation plans. The main body and supporting structure for the gas holder, and the foundation strength calculation sheets are also shown. Descriptions are given also on the facilities to deal with variation in demand quantity and supply quantity. (NEDO)

  5. Report on investigations in fiscal 2000 on the projects to support introduction of environment friendly coal utilization system. Green helmet project for briquette production plant - Mae Moh coal mine, Thailand; 2000 nendo kankyo chowagata sekitan riyo system donyu shien jigyo chosa hokokusho. Briquette seizo setsubi ni kakawaru green helmet jigyo (Thai koku Mae Moh tanko)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    This Green Helmet Project is intended to suppress generation of environment polluting substances in association with coal utilization in Thailand by demonstrating and improving the proliferation infrastructure for the clean coal technology to be used widely in Thailand. The project is also intended to serve for stabilized assurance of energies for Japan. The demonstration project related to briquette manufacturing facilities executed as one of the 'Projects to support introduction of environment friendly coal utilization system' is intended to manufacture at low cost a briquette which is low in odor, free of smoke, and suppressed largely of sulfur oxide generation. The briquette is made by adding clayish minerals, sulfur, a fixing agent and a binder into brown coal being a low grade coal. The project implements proliferation of the technology to reduce environmental load associated with coal utilization in developing countries according to the situation and needs of the counterpart countries. The present project has performed the site surveys and guidance of operation and maintenance techniques as follow-up works of the demonstration project having been completed by cooperation between Japan and Thailand. It is considered that what had been intended in the beginning has been achieved sufficiently. (NEDO)

  6. Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project of circulating fluidized bed boiler (Jinzhou Coal-Thermal Power Corporation); 1997 nendo seika hokokusho (kankyo chowagata sekitan riyo system donyu shien jigyo). Junkan ryudosho boiler ni kakawaru jissho jigyo (Jinzhou netsuden sokoji)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To verify the clean coal technology to be diffused in China and consolidate its diffusion basis, demonstration project of circulating fluidized bed boiler was conducted through the cooperation with China which is positive in its introduction. This report describes its characteristics. Coal and limestone are supplied in a lower part of combustion chamber, and are mixed with circulating ash by fluidized air for combustion. Densely fluidized bed the same as the bubbling fluidized bed is formed in the lower part of combustion chamber, which provides excellent stability in ignition and combustion. Particles including ash, char and limestone formed during the combustion are discharged into the cyclone through the convection heat transfer part at the outlet of combustion chamber with the combustion gas flow. Since the gas temperature is lowered to 400 to 500degC at the convection heat transfer part, troubles of the ash circulating system can be prevented. The combustion gas separated from ash at the cyclone is discharged through the heat exchanger and precipitator, and the collected ash is returned to the lower part of combustion chamber. In FY 1997, design, fabrication, procurement/inspection, field survey/meeting, survey of visitors/meeting, and education were carried out. 4 figs., 4 tabs.

  7. FY 1999 report on the potential survey of the environmentally friendly type coal utilization system - Dispatch of engineers. A. Project for supporting the introduction of the environmentally friendly type coal utilization system (model project)/pre-survey for the potential survey; 1999 nendo kankyo chowa gata sekitan riyo system kanosei chosa. Senmomka haken A. kankyo chowa gata sekitan riyo system donyu shien jigyo (model jigyo) - Kanosei chosa no jizen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of the improvement of coal utilization technology and environmental preservation, the paper conducted the pre-survey of the introduction of coke oven gas desulfurization facilities in China and pre-survey of potentiality of the environmentally friendly type coal utilization system in India. The pre-survey in China was made for Anyang Steel Group Co. Ltd. and Laiwu Steel Group Co. Ltd. to judge their adaptability as site for the demonstrative project on the introduction of coke oven gas desulfurization facilities. As a result, it was confirmed that the former satisfied the conditions on Japan side such as the space for installation and prospect for fund raising. However, the amount of COG treatment was larger than that planned at Japan side, and it was found that as to the recovered sulfur, the company wanted the solid sulfur different from the fused sulfur planned at Japan side. In the survey in India, explanations were made to India of CFBC and the fluidized bed cement sintering system, bio-briquette production facilities, facilities for environmental measures, coal reforming technology, etc. At the same time, the site survey was made to examine/analyze possibilities of spread/development of Japan's CCT. (NEDO)

  8. Marketing analysis support system; Marketing bunseki shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-01-10

    Fuji Electric Co., Ltd., in collaboration with Shitashion Japan and Arthur Andersen Ltd., developed a 'marketing analysis support system' which integrally analyzes evaluation factors of various dimensions explaining consumers' purchasing behaviors and which supports business for the efficient operation of product development and demand prediction. This system breaks down products into each evaluation factor from psychological and physical viewpoints, and carries out various kinds of multivariate analysis, thereby making it easy to understand visually, for example, what evaluation factors decide relative positional relations between evaluation factors or between products as well as the position of a product in the whole. Further, more precise marketing analysis and prediction become possible by visually grasping blank areas of products, extent of competition, distribution of products, composition of product series, etc. (translated by NEDO)

  9. Intelligent car guidance system (parking support system); Chiteki sharyo yudo system (chusha shien system)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This system enables a driver to park the car at a predetermined spot without the driver seeing the outside scene. The system shows on a driver seat display the steps that the driver is to follow and thereby supports the driver when visibility is poor, when the parking space is difficult to approach, when the driver is a novice, or when the driver is aged. The system ensures accurate positioning of the car by showing the steering direction and angle, the car speed, and the force of braking to the driver. For this purpose, the system knows the absolute car position by the use of an RFID (Radio Frequency Identification) tag which is a kind of IC (Integrated Circuit) card and D-GPS (Differential-Global Positioning System), grasps the relative car position by the use of a gyroscope, and collects data from plural sensors, which are complementary to each other, such as a car-speed sensor and a steering sensor. (translated by NEDO)

  10. Investigations on installation of the heat exchange system in geothermal wells; Chinetsu koseinai netsukokan system donyu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The heat exchange system in geothermal wells is a system that replaces the air source heat pump and uses underground beds or groundwater as a heat source to heat rooms by collecting underground heat in winter, and cool rooms in summer by operating a heat media circuit in reverse direction through the action of a reverse flow valve to discharge heat underground. This paper describes feasibility investigations on the system including its technical trend for introducing the system technology. Technological and economic discussions were given by classifying the intra-well heat exchange device in its installation direction (horizontal loop type and vertical installation type), underground heat exchange media (antifreeze solution/water cyclic system and direct expansion system), and underground heat transfer (heat conduction system and heat convection system). As a result of discussing each system, it was concluded that the following two systems are promising: A = vertical installation, antifreeze solution/water cyclic and heat conduction system, and B = vertical installation, antifreeze solution/water cyclic and heat convection system. Since the system B was found to have better efficiency and economy among both systems, it is necessary to verify an intra-well heat exchange system and operation methods that suit the system B effectively. 21 refs., 8 tabs.

  11. Introduction effect of a load levelling system in an electric power system with a photovoltaic and wind system; Taiyoko/furyoku hatsuden wo donyu shita denryoku keito ni okeru fuka heijunka shisutemu no donyu koka

    Energy Technology Data Exchange (ETDEWEB)

    Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S. [Maizuru College of Technology, Kyoto (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan)

    1998-12-05

    Introduction effect of load levelling system by a battery in an electric power system by a battery in an electric power system with a PV and wind system is investigated. Charge and discharge power of the battery are determined from a load curve and every hour data of PV and wind output. Annual cost of the power system is calculated from the generating power and the capacity of each source via the installed utility capacity and the capacity factor. It is found that (1) the battery system reduces the maximum demand and improves the load factor, (2) the cost effect of the battery system when introducing the PV system is higher than that when introducing the wind system. (author)

  12. Achievement report for fiscal 1998. Home rehabilitation system for aphasia patients; 1998 nendo seika hokokusho. Shitsugosho zaitaku rehabilitation shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Development has been made on the element technologies for a home rehabilitation system for aphasia patients. First, studies were performed on an authoring procedure for aphasia patient training, and partial trial production and development were carried out on an authoring system for the training program formula. Then, studies were executed on a training simulation and analysis filter, and partial trial production and development were implemented on a home rehabilitation supporting and self-teaching system. Next, an input and output mechanism for voice signal processing was studied, and aphasia patient and caregiver human interface was partially fabricated on a trial basis. In addition, a remote rehabilitation communicating method was researched, and partial trial production was carried out on a remote rehabilitation evaluation and diagnosis support means. Finally, communication assisting means were researched, and a communication assisting system was partially produced on a trial basis. Good evaluation results were given on a demonstration system. Although partial indications were given on minute parts, practical agreement was obtained as a whole. Great expectation was given particularly on the remote rehabilitation system and the authoring system. (NEDO)

  13. Optimum design of automobile seat using statistical design support system; Tokeiteki sekkei shien system no jidoshayo seat eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Kashiwamura, T [NHK Spring Co. Ltd., Yokohama (Japan); Shiratori, M; Yu, Q; Koda, I [Yokohama National University, Yokohama (Japan)

    1997-10-01

    The authors proposed a new practical optimum design method called statistical design support system, which consists of five steps: the effectivity analysis, reanalysis, evaluation of dispersion, the optimiza4ion and evaluation of structural reliability. In this study, the authors applied the present system to analyze and optimum design of an automobile seat frame subjected to crushing. This study should that the present method could be applied to the complex nonlinear problems such as large deformation, material nonlinearity as well as impact problem. It was shown that the optimum design of the seat frame has been solved easily using the present system. 6 refs., 5 figs., 5 tabs.

  14. Charcterized surpervisory control system for elevators and its support equipment. Elevator koseika gun kanri system to sono shien sochi

    Energy Technology Data Exchange (ETDEWEB)

    Tobita, T.; Fujino, A.; Yoneda, K.; Ueshima, T. (Hitachi Ltd., Tokyo (Japan))

    1991-12-20

    Objective of elevators plural control system for performing the operation control of multiple elevators is to improve the service to users. The service improvement toward a conventional plural control system is mainly to reduce waiting time on the riding floor from the calling button being pushed till elevator reaching the riding floor. Subsidiary to it, merely energy-saving is carried out. In the present study, a characterized supervisory control system was developed to make plural supervisory control receiving the requests from users to reduce not only the usual waiting time but also riding time and congestion inside. In order to meet the requests of users, a characterized support equipment was produced dialogically by combining fuzzy ratiocination, production system as well as simulation. The effects thereof were confirmed. 12 refs., ll figs., 2 tabs.

  15. Pipeline control support system, 'pipe navigation'; Kanro kanri shien system 'kannabi'

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-01-10

    'Pipe navigation' is a pipeline control support system which employs GIS/GPS (geographic information system/global positioning system) technology in controlling information of water pipeline and incidental facilities, using a pen note/personal computer as the operating base. These pen computers can be carried to the spot and used in displaying pipeline/incidental equipment and retrieving related information. The main features as follows:(1) Memo preparation is possible at an arbitrary place with handwriting ease. The memo data so prepared can be taken in other terminals and shared.(2) Communication with remote places is possible by transmitting drawings, prepared memo data, etc., as in facsimile (3) Confirmation of the present position and navigation are possible (GPS function), demonstrating power in a restoration work at the time of earthquake for example.(4) Inputting and maintenance of each facility information are possible through the data input support function even by general users easily. (translated by NEDO)

  16. Fiscal 1995 survey report on the environmentally friendly type coal utilization system introduction support project. Verification project on the circulating fluidized bed boiler; Kankyo chowagata sekitan riyo system donyu shien jigyo. Junkan ryudosho boiler ni kakawaru jissho jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    In relation to the circulating fluidized bed boiler which reduces the amount of sulfur oxides emitted in coal utilization, a verification project was carried out on installation of the equipment and spread activity in China and the Philippines contributing to the control of environmental pollutant associated with coal utilization and the effective use of energy. At the Fanshan area, installed was a 10t/h internal circulating fluidized bed boiler. At the performance test, coal includes around 7% of impurities such as stone, and the impurities should be excluded continuously at the time of actual run. Therefore, the boiler efficiency had to be changed from 89.5% to 85.8%. Further, power generation facilities have not yet been finished, and the overall operation of boiler turbine has not been executed. At the Zibo area, a 30t/h external circulating fluidized bed boiler was installed. The boiler efficiency reached 86.1%, over the targeted value. At the Batangas area in the Philippines, a 10t/h internal circulating fluidized bed boiler was installed. The boiler efficiency reached 85.8%, over the designed value. About the coal produced in the Philippines, slagging was feared, but the combustion state was favorable. 82 figs., 21 tabs.

  17. Feasibility study on introducing new energy systems into Asian villages; Asia sonraku ni okeru shin energy donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For improvement of living standards in unelectrified areas of Asia, the feasibility of new energy power generation systems was surveyed. The degree of electrification of local areas is different every country, and Thailand is ahead of other countries, while Laos and Cambodia are most unelectrified. Power supply of 100W/house seems to be adequate for local areas because of weather condition, housing situation and life-style. Economic support and education on electricity are necessary for poor areas. Although needs for new energy is increasing, the priority is given to industrial and urbanized areas because of cost and investment effects, and remote areas are dependent on grant- in-aid. Resources of photovoltaic, wind power and micro- hydraulic energies are abundant, however, selection of energy and verification of its usability are important, and the local energy density maps were thus prepared. In introduction of new energy, after selection of energy suitable for an area concerned, such geographical and social conditions should be surveyed as road condition, water rights, land utilization, economic support system, policy and intention of inhabitants. 76 refs., 68 figs., 91 tabs.

  18. Economical effect of introducing a photovoltaic system on future electric power system; Shorai no denryoku keito eno taiyoko hatsuden system donyu ni yoru keizaiteki eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Akata, N.; Kenmoku, Y.; Sakakibara, T. [Toyohashi University of Technology, Aichi (Japan); Kawamoto, T. [Shizuoka University, Shizuoka (Japan); Nakagawa, S. [Maizuru National College of Technology, Kyoto (Japan)

    1997-11-25

    Economic impact of introduction in the future of photovoltaic power generation (PV) systems into the commercial power system is discussed from the electric utilities` point of view. In the discussion, future demand for power is predicted from the demand for power in the base year, and the optimum power source configuration corresponding to the future demand and power generation curve are worked out by use of linear programming. Then, the fixed cost and variable cost are calculated for each of the power source components, and then the expected reduction in cost per unit of power generated is calculated. As the power sources, the hydroelectric, pumped storage, oil-fired, coal-fired, LNG-fired, combined cycle, and atomic technologies are considered. The conclusion is stated below. Upon introduction of PV power equivalent to 10% of the maximum demand power, the maximum power in the service area of Chubu Electric Power Co., Inc., will be reduced by 1.23GW in 2025, and the yearly demand power by 5472GWh. Since PV lowers the peak, an increased number of power sources low in variable cost will be used although such will be low in tracking capability. An increase in power demand will enhance the cost reducing effect of the PV system. 5 refs., 4 figs., 3 tabs.

  19. Study of human interface for narrow road drive assist system considered characteristic of driver; Driver no tokusei wo koryoshita kyoro soko shien system no human interface no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, A [Subaru Research Center Co., Tokyo (Japan); Amada, N; Kawashima, H [Keio University, Tokyo (Japan)

    1997-10-01

    The measurement of driver`s watching point, driving time on narrow road and the evaluation of stress etc. were conducted in order to construct the narrow road drive assist system using the stereo image recognition system. Consequently, the driver`s thinking process, stress factor and the indispensable information for this system were clarified. 4 refs., 8 figs., 3 tabs.

  20. Development of research activity supporting system. 2. Evaluation of desktop video conferencing; Kenkyu katsudo shien system no kaihatsu. 2. Enkaku kijo uchiawase hoshiki no jitsuyosei hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Tsutsumi, F.; Hishitani, J.; Matsui, S. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-03-01

    Desktop video conferencing (DVC) system and its software were investigated. A test system was actually constructed. Based on the test results, its practical advantage and disadvantage were illustrated. The DVC system was constructed using general LAN, and operation experiments were conducted, as to research activity. From the interview with participants and analysis of conversation history, advantage and disadvantage of this system were clarified. Performance of the trial system was examined using practical LAN, to compare with the performance of commercial systems. When using LAN, the same problems were given. It was found that the DVC system can not substitute for the conventional real face to face meeting, but it is suitable for some communication styles, for example free participation meeting or collaboration based on the same objective, which has been hard up to this time. In addition, software was made as trial, by which reservation of meeting, announcement, and calling can be carried out. 26 refs., 6 figs., 5 tabs.

  1. Empirical analysis of consumer decision making processes on setting up residential photovoltaic systems; Jutakuyo taiyoko hatsuden system no donyu ni kansuru ishiki bunseki

    Energy Technology Data Exchange (ETDEWEB)

    Iuchi, M; Okawara, T; Tsuchiya, T [Central Research Institute of Electric Power Industry, Tokyo (Japan); Konakayama, A [Tokai Univ., Tokyo (Japan)

    1996-10-01

    Inquiries are made to consumers (monitors) who own a photovoltaic power generation system at their houses, and their replies are analyzed for isolating the factors involving the purchase of this domestic power generating system. A large part of the monitors are 40-50 years old males in the relatively high income bracket. They are very interested in problems of global environments, resources, and energy, and are inclined to assume value-consciousness and life-style which encourage them to love health and nature, participation in social functions, and decision-making. The need for the protection of global environments occupies more than 90% of the reasons for their adoption of photovoltaic power generation. The monitors strongly feel, however, that they paid very much for the apparatus although they were granted some subsidies. As for motives for their acquisition of the system, their answers are categorized into four groups according to their responses as to whether (or not) they expect economic merits though dependent on future development and whether (or not) they accept the current energy policies. The result shows that some monitors think like average citizens. 17 refs., 22 figs., 11 tabs.

  2. Achievement report on research and development of medical and welfare equipment technology. Lavatory training system; Iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Haisetsu jiritsu shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-11-01

    Research and development of a lavatory training system is carried out to enable bed-ridden aged people to evacuate unaided and thereby to elevate their consciousness of self-reliance. The developed system consists of a multi-functional bed with a built-in transfer unit and a movement assisting system. The multi-functional bed consists of a device that automatically transfers the patient abed to a position on the bedside portable toilet, a device that is remotely controlled to change the posture of the patient from the in-bed state to a seated state, and an audio-visual system that encourages the patient into self-reliance. The movement assisting system enables a patient, who needs people's help in rising from the bed and in walking to the lavatory, to stand up, sit down, and walk, all unaided. The system has undergone field tests at 6 locations in hospitals, public facilities, and residential houses. The result is that for people of Category III it is almost certain that they can travel safely thanks to the system. The system is again evaluated high in barrier-free residential environments. (NEDO)

  3. FY 2000 Feasibility study on the environmentally-friendly coal utilization systems as part of the international project for coal utilization measures. Feasibility study on supporting introduction of the environmentally-friendly coal utilization systems in Vietnam (Model project for introduction of advanced coal preparation systems); 2000 nendo kokusai sekitan riyo taisaku jigyo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa jigyo Vietnam ni okeru kankyo chowagata sekitan riyo system donyu shien jigyo (kodo sentan system donyu model jigyo kanosei chosa jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    The feasibility study was conducted on a model project in Vietnam, aimed at solving the environmental pollution problems resulting from use of coal by demonstrating and disseminating the Japan's environmental technologies in the Southeast Asian countries. The feasibility study was conducted for the Cua Ong Coal Preparation Enterprise, which has the largest coal preparation capacity in Vietnam and port facilities. It is treating raw coal from 10 coal mines for classification and preparation, and shipping coal of various types that meet the standards for domestic use and export. The survey results point out that unrecovered coal remains in waste water discharged from the coal preparation plants to pollute the sea area, and that quantity of the refuse increases because of the unrecovered coal it contains. The environmental technologies needed to introduce include modification to variable wave pattern type jigging separator, refuse height measuring instrument and automatic controller, circulating heavy medium gravimeter, highly functional settling pond, and flocculent facilities. (NEDO)

  4. Practical application of a field work information support system for one-stop service; One stoop service wo mezashita genchi sagyo joho shien system no jitsuyoka kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ishikawa, M. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1998-04-10

    This paper reports the current research result of the field work information support system in a one-stop service system. The work arrangement in the branch office of an electric company is how to assign the service operator efficiently and accurately for the transfer to the customer. This problem is grasped as a traveling salesman problem (TSP) of `make the round of `n` works by `m` persons for processing and return to the branch office with the branch office as a start point`. The system in which the day`s schedule of each operator can be automatically created by entering only the work schedule (including limitation conditions (difficulty degree of work contents or time appointment) and skill management information of each work) was investigated. The compatibility and evaluation of each traveling route search method were carried out. As a result, the genetic algorithm is judged to be fully practical. The communication information for field work could be retrieved in real time using PHS. This system can also be applied to the maintenance or consulting including a disaster or accident as well as general work. 4 figs., 1 tab.

  5. Study of installation of PV systems at campus; Campus ni okeru taiyoko hatsuden donyu ni kansuru kenkyu (taiyo denchi nomi wo secchishita baai no yobi kento)

    Energy Technology Data Exchange (ETDEWEB)

    Tsuboi, N.; Tanaka, H.; Okumiya, M. [Nagoya University, Nagoya (Japan)

    1997-11-25

    In terms of energy consumption, environmentality and economical efficiency in the case of installing the photovoltaic power system on the rooftop of the university campus, a comparative study was conducted with other power generation systems. As objects to be comparatively studied, selected were the all-electric type centralized space heating/cooling system, cogeneration system, nighttime heat storage system and centralized system with solar cells installed. The panel area of the PV system is 10,000m{sup 2} on the rooftop and 7,000{sup 2} on the outer wall. About data on solar radiation, average values obtained in Nagoya were used. Assessment was made in terms of energy consumption amount at the time of operation, system COP, emission amounts of CO2, NOx and SOx at the time of manufacturing and operation, initial cost, running cost, etc. As a result of the study, an effect of reducing global warming gas was admitted in the PV system. However, the initial cost of the solar cell panel was high, and the life cycle cost of the PV system was lower than other systems. 1 ref., 7 figs., 3 tabs.

  6. Report on achievements in proliferation project to introduce environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998; Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This paper describes the discussion report for fiscal 1998 on the CMG (coal methane gas) recovery and utilization project to be implemented from fiscal 1998 through fiscal 2002 at Tiefa Mining Bureau of Liaoning Province in China. The Daixing mine was selected as the survey object. The introduced technologies and facilities include test drilling for degassing (medium measure horizontal degassing of 300-m class), induction from degassing holes, fly ash sealing, sealed gas degassing, surveillance and control technologies and facilities. The recovered gas is to be supplied to the cities of Tiefa and Tieling as town gas, for which compressed gas feeding and controlling technologies and facilities will be introduced. This paper lists the gush-out quantity (1,000 Nm{sup 3}), the recovery quantity (1,000 Nm{sup 3}), the recovered gas concentration (%), the utilization quantity (1,000 Nm{sup 3}), and the utilization rate (%). The figures for the respective items before and after the implementation are 128366, 32949, 44.5, 7000, 5, 123500, 43890, 49.1, 39826, and 32. The quantity of gas gushing out at facings decreases in association with increase in the recovered gas quantity, whereas the gas concentration at facings in the Daixing mine in 2003 is estimated to decrease to 0.1%, contributing to safe mining operation. The test drilling for medium measure horizontal degassing expands the degassing assured scope per one test drilling seat, and can reduce the total test drilling length and construction amount. (NEDO)

  7. Basic studies on design supporting system of offshore structure. Part 2. Implementation of structural design supporting system of offshore structures; Kaiyo kozobutsu wo taisho to shita sekkei shien system ni kansuru kisoteki kenkyu. 2. Kaiyo kozobutsu no kozo sekkei shien system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Nomoto, T.; Hamada, K.; Aoyama, K. [The University of Tokyo, Tokyo (Japan)

    1996-12-31

    In order to improve the existing design-supporting system for offshore structures, new functions are added to evaluate information of the products, especially those for structural designs. The structural analysis system should be provided with a function of design modification, to efficiently support the structural analysis of these structures. The new system adds hierarchy of various offshore structure models and three-dimensional dimensions to clarify structural and geometrical constraints and design-modification function. The design-modification function is included by use of the hierarchy. The other new functions are finite element analysis systems for the main structure and components, and rigidity calculation for the main structure. The main structure and functional element models are confirmed to be useful also for utilization of information, and provide necessary information of the product models. 11 refs., 11 figs.

  8. Basic studies on design supporting system of offshore structure. Part 2. Implementation of structural design supporting system of offshore structures; Kaiyo kozobutsu wo taisho to shita sekkei shien system ni kansuru kisoteki kenkyu. 2. Kaiyo kozobutsu no kozo sekkei shien system no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Nomoto, T; Hamada, K; Aoyama, K [The University of Tokyo, Tokyo (Japan)

    1997-12-31

    In order to improve the existing design-supporting system for offshore structures, new functions are added to evaluate information of the products, especially those for structural designs. The structural analysis system should be provided with a function of design modification, to efficiently support the structural analysis of these structures. The new system adds hierarchy of various offshore structure models and three-dimensional dimensions to clarify structural and geometrical constraints and design-modification function. The design-modification function is included by use of the hierarchy. The other new functions are finite element analysis systems for the main structure and components, and rigidity calculation for the main structure. The main structure and functional element models are confirmed to be useful also for utilization of information, and provide necessary information of the product models. 11 refs., 11 figs.

  9. Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project on simplified desulfurizers; 1997 nendo seika hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (kan`i datsuryu setsubi ni kakawaru jissho jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To reduce SOx with coal utilization, a desulfurizer is introduced in Thailand as diffusion activities in the demonstration program. The purpose is to reduce the environmental pollutants. For this desulfurizer, lime mud mainly composed of lime stone is used as an absorber. SO2 in the flue gas is absorbed by the slurry of lime mud, to form calcium sulfite. The calcium sulfite blown in the bottom of recycling tank is oxidized by oxygen in the air, to form gypsum. The gypsum is recovered as a by-product. In this fiscal year, a feeder of lime stone, spray nozzles, and various analysis apparatuses were supplied. Supervisors for electric instrumentation/control were also dispatched as well as for main body construction, to carry out the instrumentation setting works, check of sequences, and adjustment of apparatuses. After the test operation, supervisors for the demonstration operation were dispatched up to March 1998, to conduct the cooperation works between Japan and Thailand sides. Thus, successful and successive demonstration operation was confirmed. 21 figs., 6 tabs.

  10. Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Follow-up project on circulating fluidized bed boiler introduction (Calaca Batangas Thermal Power Station); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (junkan ryudosho boiler ni kakawaru follow up jigyo (Calaca Batangas karyoku hatsudensho))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the follow-up project, to promote the diffusion of results of the clean coal technology (CCT) model projects, experts of circulating fluidized bed boilers were dispatched, to guide and advise for the operation of facilities introduced in these projects. The purpose of these projects is to diffuse the CCTs, and to support the promotion of environmental measures. Some guidance and advice about operation processes, data processing, operation regulation, maintenance, and boiler maintenance works were provided to the Ministry of Energy and Electric Power Corporation of the Philippines. Semirara, Malangas, and Samar coals in the Philippines were used for the tests. The boiler facilities could be operated by Philippine operators themselves. Based on the guidance and advice about operation processes, combustion tests using various Philippine coals were also planned and conducted by themselves. The maintenance techniques were transferred to Philippine operators through the inspection, repair and advice. The Philippine side understood the technologies well, and the circulating fluidized bed boiler technology was independently educated in the Philippines. 23 figs., 16 tabs.

  11. Fiscal 1997 survey report. Preparatory survey for a manual on the introduction of high efficiency thermal utilization systems; 1997 nendo chosa hokokusho. Kokoritsu netsu riyo system donyu manual no sakusei choa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To cope with the energy issue and global environmental issue, it is necessary to forcibly promote energy conservation. In the light of the present situation that in Japan only 1/3 of the primary energy consumed is effectively used, policies are being prepared for promotion of the introduction of high efficiency thermal utilization systems including `a project for formation of the environmentally friendly type energy community` promoted by NEDO. However, it is hard to say that the introduction is being actively promoted. The cause is that they do not fully understood the present status of high efficiency thermal utilization systems, procedures for introduction, subsidy system, etc. Therefore, a manual was made to present to self governments and enterprisers who are planning to introduce the system. To be concrete, there are the six systems: cogeneration use thermal supply system, unused energy use thermal supply system, heat storage use thermal supply system, waste use thermal supply system, plant surplus energy use thermal supply system, and cascade type thermal supply system. 28 refs., 38 figs., 42 tabs.

  12. Fiscal 1998 research report. Feasibility study on next-generation environment-friendly urban transport systems; 1998 nendo chosa hokokusho. Jisedai kankyo kyosei toshi kotsu system donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research arranges recent public transport system technologies such as LRT, and clarifies their technical issues to be overcome and developmental courses, and the improvement effect of their energy efficiency and CO{sub 2} reduction effect by such measures to contribute to development of next-generation public transport systems. The outlines and features of LRT, monorail/trolley bus and AGT as existing public transport systems are arranged. In the EU, development of tramways using rubber tires is in promotion. The concept of a next-generation environment- friendly urban transport system is prepared based on features of every public transport system. Since a trolley system causes traffic congestion and environment deterioration, introduction of an independent transport system with fuel cell is necessary in the future. The technical issues and solutions for construction of the next-generation transport systems are analyzed. Fuel cell and ITS are important candidates. Substitution of the next-generation transport system for existing buses showed a CO{sub 2} reduction effect of 3.91 Mton/y in Japan. (NEDO)

  13. Research and development of system to utilize photovoltaic energy. Study on the scenario for the diffusion of photovoltaic power generating systems; Taiyoko hatsuden riyo sytem no kenkyu kaihatsu. Taiyoko hatsuden donyu fukyu scenario sakusei no tame no chosa

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on a survey to prepare scenario for the diffusion of photovoltaic power generating systems. Introduction target planned with help of a diffusion simulation was verified by calculations using simulation models. The calculations made the following points clear: facility costs and power generation costs for photovoltaic power generation systems, amount of introduced photovoltaic power generation systems, number of facilities introducing photovoltaic power generation systems, policy cost to achieve the target, annual power generation amount, oil substituting effect, carbon dioxide reducing effect, and market sizes. Power generation cost in fiscal 2000 would drop down to 53 yen per kWh in new installation in independent houses and down to 31 yen per kWh in systems used in schools. These reductions are the result of progress in mass production as a result of positively implementing the aiding policies. The required diffusion aiding policies revealed from the simulation results include expansion of subsidy operations for house construction, introduction of the systems into public facilities performed by public organizations, aid to system introduction into private business entities, subsidy to facility investments, and enforcement of power purchase institutions. 3 figs.

  14. Fiscal 1994 report on the survey of making models for introducing petroleum substituting energy systems; 1994 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    In the promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. appropriate and concrete guidance for introducing energy systems which meet with features of the areas and buildings and courses for how to construct infrastructures of towns or cities in case of development and redevelopment. Recently, also in local governments, etc., there are seen attitudes toward positive study of introduction of energy conservation systems and petroleum substituting energy systems in case of redevelopment, and the situation is that the spread and expansion are expected by giving appropriate guidance for the introduction. Accordingly, the study makes analyses of the trend and characteristics of developmental projects and makes/arranges models of promising petroleum substituting energy systems, aiming at contributing to promotion of guidance for the introduction to local governments, entrepreneurs, etc. Approximately 20 models of petroleum substituting energy systems were made which are thought to be promising. For each, the following were arranged: outline of system, introduction target, introduction effects, the point of promotion of the introduction, related subsidy systems, actual results, etc. 22 figs., 34 tabs.

  15. Report on results 1998. Research and development on high-temperature superconducting flywheel power storage (investigation on system introduction); 1998 nendo seika hokokusho. Koon chodendo flywheel denryoku chozo kenkyu kaihatsu (system donyu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    In introducing high-temperature superconducting flywheel power storage equipment to an electrical power system, adaptability is examined and evaluated concerning secondary effect that can be expected while a load leveling function is maintained. The 1998 plan is such that the functions and usages other than the load leveling are put in order for such equipment, and that the effect/adaptability in the case of the introduction into the power system is evaluated by means of simulation and literature studies. The high-temperature superconducting flywheel power storage equipment may be used for such purposes as energy adjustment for a short time, system voltage adjustment and emergency power source, other than the load leveling, on the basis of the characteristics that enable high speed control of active/reactive power and storage/release of energy. Enumerated, as the effects obtainable in introducing these uses into the power system, are enhancement in system stability, improvement in voltage stability, improvement in instantaneous voltage drop, maintenance of system frequency, compensation of fluctuating load, countermeasures against power outrage, and output leveling of intermittent power sources, and these effects were examined. (NEDO)

  16. Fiscal 1995 report on the survey of making models for introducing petroleum substituting energy systems. 2; 1995 nendo chosa hokokusho (sekiyu daitai energy system donyu model sakusei ni kansuru chosa). 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In the promotion of measures taken for energy conservation, it is necessary to give local governments, entrepreneurs, etc. guidance for introducing energy systems which meet with features of the buildings and courses for how to construct infrastructures of towns or cities in case of development, redevelopment, etc. In fiscal 1995, each of the petroleum substituting energy systems was studied more detailedly, and the trend of building facilities for the introduction was studied and arranged. Energy systems by the following were set up paying attention to energy sources, energy conversion and energy transportation as factors composing a petroleum substituting energy system: photovoltaic power generation, use of solar energy, use of wind energy, use of geothermal energy, use of biomass energy, use of waste, use of temperature difference energy, cogeneration, load levelling, wide-area energy supply, etc. Also studied and arranged were energy demand, location, the recent trend, the point of introduction of energy systems, examples of introduction, etc. in relation to indoor sport facilities, hospitals, hotels, multiple dwelling apartments, commercial facilities, offices, plants, etc. 52 figs., 55 tabs.

  17. Specified international joint research. Report for fiscal 1997 on the result of `Development of Machining Supporting System`; Kokusai tokutei kyodo kenkyu. `Kikai kako shien system no kaihatsu` 1997 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    On the basis of information obtained from actually performed designing of machines with the aid of computers, researches are conducted for the development of a system that automatically designs required machine tools, machining procedures, machining conditions, and tool paths. The research and development efforts made in fiscal 1997 are enumerated below. In the development of man-machine interfaces, one that integrates a machining procedure designing system, machining condition designing system, and a tool path designing system, all of which are subsystems belonging in a machining supporting system, is developed. In a system evaluation performed through actual machining, an interface between CAD (Computer-Aided Design) technology and a machining supporting system is evaluated, when machining is actually performed for experimentation in an environment in which a machining procedure designing system, machining condition designing system, tool path designing system, and CNC (Computerized Numerical Control) technology collaborate as integrated. As the result, the performance expected to be achieved at the beginning is realized. Two scientists of Russian Academy of Sciences are invited, and researches are conducted concerning knowledge processing technology. 20 refs., 21 figs., 10 tabs.

  18. Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Research achievements; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports the achievements in fiscal 1995 in the research and development project for an electronics design and production aid system of simple operation type (MATIC). The project is intended to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. The working group (WG)I, related to automobiles and components thereof, improved functions of the primary system and continued demonstration tests. The group launched for the secondary system a system development that makes timely information transmission and receipt possible among research and development enterprises, local assembly enterprises and facility and parts suppliers. The WGII (household appliances and their parts) designed and developed an electronic catalog system based on pre-prototypes developed independently by different countries, and performed demonstration tests. The WGIII (textiles and apparels) carried out with China demonstration tests on the international EDI system, translation system and CAD/CAM system. It also developed a sewing technology standards system. It installed equipment and devices in Indonesia for preparation of the demonstration tests. (NEDO)

  19. Effect of heat-insulating wall on input energy of a photovoltaic/solar/air-heat system for a residence; Jutaku no kodannetsuka ni yoru taiyoko netsu/taiki netsu system no donyu energy sakugen koka

    Energy Technology Data Exchange (ETDEWEB)

    Kenmoku, Y; Sakakibara, T [Toyohashi University of Technology, Aichi (Japan); Nakagawa, S [Maizuru College of Technology, Kyoto (Japan)

    1996-10-27

    A proposal was made to introduce a photovoltaic/solar/air-heat system which positively utilizes natural energy in order to curtail consumption of fossil energy, corroborating that the system has greatly reduced energy input in the primary energy level in a house. This paper examines the effect of curtailment of energy input in the case of reducing the load of air conditioning through the high heat insulation of a house. The energy input was evaluated by calculating additional equipment energy needed newly for the high heat insulation. The system performance and the energy load varied greatly depending on weather conditions. The subject system consisted of solar cells, inverter, heat concentrator, heat storage tank, heat pump and gas hot-water supply device. The thickening of the insulation sharply reduced heating load in the house, thereby decreasing fuel energy substantially. An insulation material of 100mm thick was capable of reducing energy input by 16-23% compared with that of 50mm thick. 5 refs., 5 figs, 3 tabs.

  20. Achievement report for fiscal 1999 on research and development of technologies for medical welfare equipment. Rehabilitation system for upper limbs and lower limbs; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Shintai kino rihabiri shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    This project aims to develop physical function measuring and training systems equipped with a variety of feedback utilities and widely applicable to the prevention of the elderly from physical function degradation, to the preservation of physical functions, and to their recovery from mild physical difficulties, thereby helping the elderly enjoy independence and participation in social activities. Possibilities will be studied of providing them with engineering support in the field of exercise therapy through the analysis of the characteristics of old people's movement, and the findings will be applied to the designing and assessment of welfare and nursing equipment and also fed back to their development environment. In the gait training system, the suspension force is adjusted according to data from the force plate and various position sensors, and the system produces an effect similar to that of walking in the water. The lower limb rehabilitation system facilitates the treatment of the aged or handicapped people, and patients suffering from cerebral disorders, at any of their physical positions from lying to standing. The upper limb training support system is to provide motivation for the aged or handicapped people suffering from mild difficulties in their upper limbs. In this fiscal year, basic designs have been prepared for the gait training system and the lower limb rehabilitation system, and a preparatory survey is conducted for the upper limb training support system. (NEDO)

  1. Achievement report for fiscal 1998 on Simple Operation Type CAD/CAM System Development through International Cooperation; 1998 nendo 'kan'i sosagata denshi sekkei seian shien system no kaihatsu ni kansru kenkyu kyoryoku' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The subject project is implemented in the fields of automobiles and their parts, electrical home appliances and their parts, and textile and apparel. In the field of automobiles and their parts, a prototype is developed of an integrated information management system which is to serve between corporation head offices and assembling businesses overseas, and another prototype is developed of an inter-business technical data serving system which is to serve between overseas assembling businesses and supporting businesses, both involving Japan, Indonesia, and Thailand. In the field of electrical home appliances and their parts, a prototype is developed of an electronic catalog system in a joint endeavor with research institutes of Indonesia, Malaysia, Singapore, and Thailand, and a demonstration test is conducted. A design concurrent engineering system is developed by Japan and Malaysian research institutes. In the field of textile and apparel, prototypes are developed, by Japanese, Chinese, and Indonesian apparel manufactures, of an apparel manufacturing specification system, international EDI (electronic data interchange) system, translation system, and a CAD (computer-aided design)/CAM (computer-aided manufacturing) data interchange system. (NEDO)

  2. Report on simple operation type CAD/CAM system development through international cooperation. Current statuses of Asian countries; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Asia shokoku no jokyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Information systems, mainly aided by computers, are becoming increasingly important, contributing to development of wide areas of societies and economics, to begin with. However, few developing countries have established sufficient information systems, in spite of their strong desires to do so, which will further widen the gap between them and advanced countries, where these systems are acceleratedly advancing. Given these situations, Center of International Cooperation for Computerization (CICC) has been implementing various projects for providing assistance to and cooperation with oversea countries which are trying to develop information systems. This report summarizes the project, which CICC has been commissioned by NEDO as part of the cooperation programs, for manufacturing technology supported by advanced and integrated information system through international cooperation. It outlines the research cooperation memoranda NEDO has concluded with Indonesia, Malaysia, Singapore and Thailand, and the authorities of China, Indonesia, Malaysia, Singapore and Thailand. (NEDO)

  3. Fiscal 2000 achievement report on the research and development of medical and welfare apparatus/technology. Home rehabilitation system for aphasia patients; 2000 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Shitsugosho zaitaku rehabilitation shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    In the effort to develop an authoring system for assistance programs, a self-training system to enhance home rehabilitation, a remote rehabilitation evaluation/diagnosis supporting system, and a communication assisting system, the systems developed in the preceding fiscal years were customized and, together with their operation manuals, introduced to seven hospitals and subjected to evaluation. The results were analyzed, and improvement centering on the ease of operation was carried out. Various development efforts were exerted to improve on what were strongly demanded. As for the aphasiac/caregiver interface, it was distributed to every hospital concerned. There was a demand for immediate introduction, and then the interface was developed into a practical tool to satisfy the demand. This enabled aphasiac patients to receive training stimuli effectively through various sense organs. (NEDO)

  4. Achievement report for fiscal 1999 on research and development of technologies for medical welfare equipment. Home rehabilitation system for aphasia patients; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Shitsugosho zaitaku rehabilitation shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Element technologies under development involve (1) an authoring system for assistance program processing, (2) self-training system for supporting home rehabilitation, (3) human interface for aphasia patients and caregivers, (4) remote rehabilitation evaluation and diagnosis supporting system, and (5) a communication assisting system. Under item (1), a material incorporating interface, training contents layout and combination function, and general-purpose interface specifications are determined, and a one-piece system is designed and developed. Under item (2), a self-training player that behaves in compliance with the authoring specifications is designed and developed. Under item (3), a secondary unit is fabricated on the assumption of its use at an actual treatment scene. Under item (4), remotely controlled two-way face-to-face communication, camera control, shared operation of a training player, training scenario transfer component, etc., are developed and, furthermore, a one-piece system is designed and developed to support the therapist's rehabilitation assessment and diagnosis in coordination with the above-mentioned remotely controlled functions. Under item (5), a network communication component and an auxiliary function using voice synthesis are added for designing and developing a one-piece system that enables long-distance communication between the therapist and patients. (NEDO)

  5. Fiscal 1998 research cooperation project on development of the easy-to-operate electronic design/production support system; 1998 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes 'Research cooperation on the easy-to- operate electronic design/production support system' which was promoted together with Asian countries as a part of the international research projects. This project is promoted by joint research with research organizations in China, Indonesia, Malaysia, Singapore and Thailand. The project promotes the interexchange and cooperation of researchers along the memoranda on MATIC (Manufacturing Technology International Cooperation) concluded between NEDO and research organizations every country. The project is implemented by CICC (Center of the International Cooperation for Computerization) through the contract with NEDO. CICC is promoting this project with the production system future integrated information system committee, MATIC committee, and automobile, home appliance, fiber and apparel working groups. The project has been promoted by the survey in fiscal 1994, the basic planning in fiscal 1995-1996, and development of the prototype information system in fiscal 1996-1998. The final demonstration test is scheduled in fiscal 1998. (NEDO)

  6. Fiscal 1998 research cooperation project on development of the easy-to-operate electronic design/production support system; 1998 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes 'Research cooperation on the easy-to- operate electronic design/production support system' which was promoted together with Asian countries as a part of the international research projects. This project is promoted by joint research with research organizations in China, Indonesia, Malaysia, Singapore and Thailand. The project promotes the interexchange and cooperation of researchers along the memoranda on MATIC (Manufacturing Technology International Cooperation) concluded between NEDO and research organizations every country. The project is implemented by CICC (Center of the International Cooperation for Computerization) through the contract with NEDO. CICC is promoting this project with the production system future integrated information system committee, MATIC committee, and automobile, home appliance, fiber and apparel working groups. The project has been promoted by the survey in fiscal 1994, the basic planning in fiscal 1995-1996, and development of the prototype information system in fiscal 1996-1998. The final demonstration test is scheduled in fiscal 1998. (NEDO)

  7. Report on 'manufacturing technology supported by advanced and integrated information system through international cooperation'. Domestic surveys; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kokunai chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    The committee of manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC) has been established as the organization to promote necessary surveys, deliberate the research and development guidelines and themes, and thereby support the joint R and D projects with Asian countries to improve information systems for their manufacturing industries by MATIC. The R and D skeletons are set in FY 1994 for the works in and after FY 1995. The relationships between affiliates of Japanese enterprises and local enterprises, actual conditions of the manufacturing industries and so on are surveyed, in order to extract problems related to the information systems for the promising manufacturing industries in the Asian countries. Each industry has its own characteristics with respect to, e.g., numbers f parts and process steps, product life cycle, extent of automation, skill of workers, and spread of the related industries. Therefore, 3 industrial areas are picked up as those considered to be adequate for the case studies, and surveyed for the system functions, performance, elementary techniques and so on which are required to establish the information systems for their production systems. (NEDO)

  8. Research cooperation project on manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC); Kan`i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To support the advancement of basic industries including machine industry in Asian countries, research cooperation has been conducted for developing the manufacturing technology supported by advanced and integrated information system suitable for actual circumstances of individual countries. For the automotive and the parts industries, it is significant for the preparation works of manufacturing in overseas factories to possess common information between Japan and overseas factories. In this project, a system is constructed, which can be used in industries surrounding automotive industry, such as parts and facility industries, as well as in the automotive industry. In FY 1996, a primary system has been developed, and the demonstration tests were carried out. For the home electric machine and the parts industries, the technology applicable to the design of printed board circuit was developed, and the catalog of electronic parts was constructed. In FY 1996, a preliminary prototype system of the electronic parts catalog system was designed and developed. For the textile and apparel industries, the EDI, exchange system of CAD/CAM data, and construction of data bank were investigated. 87 figs., 19 tabs.

  9. Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Research results; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This 5-year project beginning in FY 1994 is aimed at joint researches with various Asian countries for development of simply operable electronic designs and manufacturing support systems, which supports development of supporting industries (SI) for manufacturing industries in these countries. The project is being implemented in a total of 5 countries, China, Indonesia, Malaysia, Singapore and Thailand, in cooperation with the research institutes with which NEDO has concluded the basic contracts. The following three working groups are established to study construction of the model systems and design these systems for promotion of the joint project in each country; (1) automobiles and their parts, (2) home electric/electronic appliances, and their parts, and (3) textiles and apparels. The FY 1995 project results are described. The working group (1) covers definitions of the business models and conditions for systematizing these models for the demonstration tests. The working group (2) covers development of the electronic catalogues, electronic yellow pages/preproto types, and concurrent engineering. The working group (3) covers the SGML sewing technique specification systems, surveys and utilization tests for network infrastructures, international EDI systems for the textile industry, and translation systems for technical terms of the textile industry. (NEDO)

  10. Result of R and D of medical welfare equipment technology in fiscal 1994. Part 7. Evacuation-support system; Iryo fukushi kiki gijutsu kenkyu kaihatsu 1994 nendo seika hokokusho. 7. Haisetsu jiritsu shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    The evacuation-support system is under development for not only the aged bedridden persons but also the persons disabled in exercising movement to excrete by themselves. When the person lying on his bed is going to excrete, his sequence of actions to be taken is to sit down on his bed, walk to the toilet, sit on it, simultaneously take off his clothes and excrete. After the excretion, the above actions are reversely taken as for as he lies on his bed. Researches are being made into the mechanical system which partially or entirely supports the above five necessary actions. The system structuring can depend upon the following five types of disabled persons` residual function: difficulty in sitting or moving without help. Paralyzed lower extremities and partially impaired upper extremities. Ability to walk with functional assistance. Ability to stand up with support but walk unstably. Ability to walk, leaning on and along the railing. In the present project, its three constituent elements are being developed which are the multi-functional bed internally equipped with transferring/riding/mounting apparatus, transfer support apparatus and multi-function portable toilet. The development of the present system is expected to be followed by that of the self-supporting excretion system which will be proper for Japanese houses. 3 figs., 1 tab.

  11. Achievement report for fiscal 1999 on research and development of technologies for medical welfare equipment. Computer-assisted analysis system for medicinal compounds; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Iyo kagobutsu sukuriningu shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    This system aims to support the selection and development of optimal compounds by resorting to compound classification, molecular superpositioning, acceptor model construction, etc., when information on the target protein structures of the numerous active compounds found by HTS (high throughput screening) is not available and, when available, by resorting to 3-dimensional protein structure modelling, docking study, etc. Investigated in this fiscal year for incorporation into the system are (1) a method of constructing a database of compounds, (2) method of classifying compounds, (3) method of molecular superpositioning, (4) development of a method of 3-dimensional protein structure modelling, and (5) a total system. In relation with item (1), investigations are conducted into the contents and management of HTS target compound data, and methods of incorporating the data into this system are studied. In relation with item (2), surveys and studies are conducted about methods of classification based on skeletal structures. In relation with item (3), application to the analysis of HTS active compounds is taken into consideration when problems are investigated relative to prior arts in molecular superpositioning. In relation with item (4), protein side chain conformation prediction methods are surveyed and studied. In relation with item (5), a user interface is developed and tentatively constructed for a total system. (NEDO)

  12. FY 2000 Report on the survey results. Survey on international cooperation for development of a system for supporting low-invasion surgical operations; 2000 nendo teishinshu shujutsu shien system kaihatsu ni kakawaru kokusai kyoryoku ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The international Medical Treatment Symposium and Exhibition were held from July 20 to the end of August, 2000 in Hannover in Germany, in which the Japan's system for supporting low-invasion surgical operations was presented and information was exchanged for the system. A total of 50 to 100 neurosurgeons visited the exhibition, held as part of the symposium, every day from July 21 to 24. The system for supporting low-invasion surgical operations is rated as the most advanced one in the world. It attracted much attention, because a number of attendees applied for operating manipulator. The research trends seen in the symposium point to early diagnosis of diseases, finer surgical operations, low-invasion type operations, use of high-function diagnosis devices for improving operations, real-time imaging, and application of DNA diagnosis to pathological diagnosis, among others. Japan is leading the world in the technological areas of micromachines, robotics, high-vision and diagnosis. The bold researches, e.g., those on artificial visual and hearing systems to be embedded in the head, are pursued more extensively in the overseas countries. (NEDO)

  13. Fiscal 1998 survey report. Welfare equipment (Development of human friendly care support intelligent equipment / Development of home welfare equipment system); 1998 nendo chosa hokokusho. Fukushi kiki (human friendly kaigo shien chino kiki kaihatsu / zaitaku fukushi kiki system kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Since disabled persons increase with a progress of an aging society, while a care power decreases with a decrease in birth rate, development and practical use of the welfare equipment contributing to self-support of aged and handicapped persons, reduction of doctors' or therapists' burdens, and as a result, reduction of medical care costs are desirable. Among them, R and D and practical use are expected of the advanced welfare equipment and system based on human engineering technology contributing to improvement of lives of aged and handicapped persons, and support of nurses and cares of disabled persons. In fiscal 1998, on both human friendly care support intelligent equipment and home welfare equipment system, this project clarified essential technical issues based on the future view, selected some themes to be newly developed in the future, and surveyed and evaluated the details of their R and D concretely. For the former, 'heart disease diagnosis and treatment total support system,' and for the latter, 'body function rehabilitation support system' were surveyed. (NEDO)

  14. Manufacturing technology supported by advanced and integrated information system through international cooperation in fiscal 1995; Kan`i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Informatization using mainly computers is more and more important contributing to the upgrading in society, economy and a variety of fields. As to informatization in developing countries, however, there has still been few to be seen. Accordingly, gaps are getting larger between developing countries and developed countries where informatization is acceleratedly advanced. In the light of such actual state, Center of the International Cooperation for Computerization (CICC) contracted with NEDO and promoted a project `Manufacturing technology supported by advanced and integrated information system through international cooperation.` This is a project to study jointly with five Asian countries with which NEDO made a basic contract, China, Indonesia, Malaysia, Singapore and Thailand. Working group is set up for each theme such as automobiles/parts, electric home appliances/parts, and fiber/apparel, to study the construction of a model house and the design of a system. In fiscal 1994, the field survey was conducted, and in fiscal 1995 the system design was started. 16 figs., 1 tab.

  15. Manufacturing technology supported by advanced and integrated information system through international cooperation in fiscal 1994; Kan`i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Among NEDO`s international research cooperation projects, the paper described Japan`s cooperation with Asian countries in development of an easy-operated electronic design/production supporting system. The project aims to realize information realtime technology by which data for design/manufacturing of machine/electronics/fiber/apparel can mutually be used among countries. For it, design data standard and electronic information exchange standard are developed. A production information integrated database system is developed for sharing processing data. Parts data are put into a library. Graphic user interface and multi-media technology are developed so as to comply with the environment of different usages. In fiscal 1994, emphasis of activities was placed on survey of the status quo of the institution of the party country, fermentation of mutual understanding, and study of a cooperative project plan. Memorandums on research cooperation were concluded with Indonesia, Malaysia, Singapore and Thailand. In addition, understanding of this project by the party country was able to be enhanced

  16. Development of research activity support system. 3. Automatic link generation/maintenance on self-evolving database; Kenkyu katsudo shien system no kaihatsu. 3. Jiko zoshokugata database deno bunsho link no jido sakusei/shufuku

    Energy Technology Data Exchange (ETDEWEB)

    Shimada, T.; Futakata, A. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-04-01

    For a coordinated task to be accomplished in an organization, documents, charts, and data produced by plural workers need to be shared by the plural workers. This information sharing setup will function more effectively when the meanings and purposes of documents, etc., are arranged in good order relative to the other documents and when they are managed as a group of documents organically linked with each other and properly updated as the task approaches completion. In the self-evolving databases proposed so far, five types of document links representing the relations between documents are automatically generated and the documents are unifiedly managed for the documents yielded by coordinated work to be arranged in a proper order. A procedure for automatically generating document links are established on the basis of information received from the document retrieval system and Lotus Notes application. In a self-evolving database, the document on either side of a link is apt to be lost due to users` moving or deleting documents. An automatic procedure is developed in this report which will enable such document links to correctly restore themselves without loss of semantic relations. 12 refs., 11 figs., 3 tabs.

  17. FY1995 study of aid system for the elderly and the disabled using metal hydride alloy actuators; 1995 nendo suiso kyuzo gokingata actuator ni yoru kaijo shien system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Purpose of the project is to develop a transfer aid system for the elderly who need assistance in moving from a bed or a chair. It can make up insufficiency of assistant persons and can help to comfortably move the elderly. It has the highest demand in rehabilitation centers or hospitals. We have been designing an actuator using a metal hydride alloy for more than ten years and have confirmed that the actuator is very useful for developing the transfer. Furthermore, we have designed the transfer from a view point of human interfaces. This research was done under the above background. 1. We studied a comfortable posture for the elderly at an initial phase of standing to design the optimal knee pad using a life-size model of a transfer. Especially, we managed to lighten the burden imposed on the elderly by referring electromyographic signals at lower limbs and ground reaction forces. 2. Since the tactile sensation of the bottom of elderly person's foot gets dull, we designed a foot stage to prevent the elderly from the dull. 3. We determined the optimal mixture rate of a metal hydride alloy and developed an elastic bellows in order to design the actuator used for the transfer aid. 4. We determined the optimal compliance to prevent the elderly from a mechanical shock and designed a mechanism so that the transfer aid can work well. 5. Based on the above results, we developed the transfer aid using the metal hydride actuator. It was ascertained that it can lift a elderly person with 80kg weight by using only 40g alloy. Furthermore, it is proved that the transfer is not heavy (about 20g weight), small, silent, and moves smoothly by a battery on the market. (NEDO)

  18. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (electronic information communications); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Denshi joho tsushin)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys were performed on the external accreditation system for engineer education such as in universities and other organizations. In the field of electronic information communications, a committee to correspond to JABEE was established to perform system build-up, where the discussions were advanced. This field was classified into the following four specified areas: general aspect of electric/electronic/information communication engineering, electronics, information communications, and information systems. A supplementary explanation was given on the educational contents except for the information systems, based on which the self-assessment criteria and the evaluation table (for trial use) were prepared. For the examiner training, instructors were invited from ABET in the U.S.A., and training meetings were held. In addition, two committee members were sent as observers to the examinations being carried out at ABET. The trial experiments were conducted for the information communications program at the engineering department of Niigata University, and the electronic system engineering class at Sendai Radio Wave Industrial College. This paper summarizes the results of the examinations. (NEDO)

  19. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (information); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Joho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys and discussions were performed on the external accreditation system for engineer education such as in universities and other organizations. In the survey on the information field, a trial was attempted on the information related course at Kyoto University and Osaka University based on the accreditation criteria discussed with an objective of establishing the external accreditation system. The trial was performed on computer science for Kyoto University and software engineering for Osaka University. The activity has provided the examiner side with an opportunity to actually experience the accreditation work, and the examiners had a feeling that the work can help improve the education. The side receiving the accreditation indicated problems in the present system including the concern about the system becoming a mere shell. In addition, participation in the accreditation examiner training work for the information field in the U.S.A. has provided useful information such as thoroughgoing observation of the duty of confidentiality. (NEDO)

  20. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (general); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Zentai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, trials and discussions were performed on the external accreditation system for engineer education such as in universities and other organizations. The current fiscal year has performed the trials of examination and accreditation at 19 universities and for 20 programs covering eight fields including chemistry, machinery, civil engineering, electrical, electronic, information communications, information processing, materials, resources and agricultural engineering. In performing the trials, the purpose and the basic policies were identified, the guidebook for actual examinations was prepared, and the program check book and the trial examination report were also compiled. Two assembly training meetings were held to train about 130 examiners, of which 65 examiner chiefs and examiners have participated in the trials for 20 schools to work for the examination. As a result of the trials, the training was found capable of having served for improvement of the engineer education program in high-level education institutions, and improvement of the accreditation criteria and examination methods to establish the external accreditation system. (NEDO)

  1. Surveys on awareness and needs of industries to external accreditation system in engineer education; Gijutsusha kyoiku no gaibu ninteiseido donyu ni taisuru sangyo kai no ioshiki to needs ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In certifying the engineer educational programs at advanced educational organizations, questionnaire and visiting surveys were performed to identify the awareness and needs of industries, and reflect the results to the external accreditation system. The questionnaire survey was conducted on 1,100 engineers acting in the wide technical areas. Effective replies were obtained from 528 engineers. The visiting survey was executed on different business areas and operations. The result of the survey revealed that, in the awareness related to international universality of the engineer education and engineer qualification, 87% answered that they feel they need them, but the cognition rate on the accreditation system has not reached even 50%. In hearing the opinions from representatives in the industries, they indicated that it is not correct to link the certification course of JABEE directly to the engineer qualification; international applicability of JABEE with America is fine, but defining the engineers who desire to come from Asian countries and work in Japan is necessary; the engineer education has its importance shifting from quantity to quality and specialization, but on the other hand diversity is also demanded; and criteria would be necessary to guarantee the minimum required knowledge and capability. (NEDO)

  2. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (civil engineering); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Doboku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys and discussions were given on the external accreditation system for engineer education such as in universities and other organizations. In the field of civil engineering, a special sub-committee was organized, and in advance to a trial examination, surveys and discussions were executed by participating in the actual examination of the engineer educational program at the engineering department of Auckland University, and by participating in the ABET trial examination by the civil engineering department of Kansas State University and the engineering department of Stanford University in the U.S.A. The trial examination was performed upon selecting the engineer educational programs of the civil engineering department of Kinki University and Tottori University. This paper describes the fundamental policies on the educational program examination work for the field of civil engineering, the self-assessment under the educational program, the direction of engineering qualification and educational accreditation, the fundamental concept of examination and accreditation and evaluation process, the works done by the civil engineering section of the science and engineering department of Kinki University, and the works done by the civil engineering section of the engineering department of Tottori University. (NEDO)

  3. Research report for fiscal 1998 on development of environmentally friendly high-efficiency energy utilization system. Research of optimum system designing technology (Research of effect of eco-energy city system technology introduction to Osaka); Kankyo chowagata kokoritsu energy riyo system kaihatsu Saiteki system sekkei gijutsu no kenkyu 1998 nendo chosa hokokusho (Osakafu). Ekoene toshi system gijutsu donyu koka no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Concerning the district in Osaka Prefecture selected for study in fiscal 1997, it is investigated whether energy efficiency is enhanced, and environmental impact reduced, by the introduction of element technologies, and the findings are compared with the results expected to be produced without their introduction. Problems about their introduction are also discussed. Taken up for study are the collection and utilization of heat from a water granulated slag manufacturing plant of an iron mill, exhaust heat reform and recovery system at a chemical plant, heat supply system driven by a high-performance heat pump capable of dealing with various kinds of fuels, compression/suction hybrid heat utilization system, and a cold heat supply system using microspheres. Annual energy consumption, CO2 and NOx emissions, and costs are calculated for each of them. Concerning these element technologies, various tasks are discussed, related to the technology of their systematization, economy, dissemination of district heat supply, and wide-area heat supply businesses utilizing exhaust heat. As the result, it is concluded that the primary energy consumption as a whole is reduced upon their introduction and that energy saving effect and environmental impact reducing effect are in presence. (NEDO)

  4. Fiscal 2000 survey report. High-efficiency energy system introduction promotion project for houses and structures - Houses (Technical classification tables prepared by analysis of proposed systems, and comments on the same); 2000 nendo jutaku kenchikubutsu kokoritsu energy system donyu sokushin jigyo (jutaku ni kakawaru mono) teian system no bunseki ni yoru gijutsu bunruihyo oyobi dokaisetsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As an energy conservation promotion measure, a project is under development for introducing and subsidizing high-efficiency energy systems and for letting their effect known publicly and widely. The number of proposed energy systems has increased greatly and technical divisions to follow in classifying them have become vague, from which problems are now arising over the execution of follow-up checks and the maintenance of fair treatment. In the effort to solve this problem, 376 propositions are analyzed and classified, a technical classification method is proposed, and an instruction manual on the method is compiled. The classification involves (1) proposed classification, (2) variation, (3) energy reduction rate, and (4) tentatively calculated cost. Item (1) deals with the basic classification (air-conditioning, ventilation, and hot water supply, and, to be considered in combination with them, options which are cooking, illumination, and others) and, item (2) covers eight items such as new/old construction, structure, and structural frame. In Chapter 1 of the report, the 376 propositions are put in order according to common classification items and an original classification table is prepared. In Chapter 2, the goals are clarified and the classification principles are defined. In Chapter 3, the classification is checked for its validity and some realistic ways of grouping are described. In Chapter 4, a classification implementation flow chart is shown. (NEDO)

  5. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium research on energy in its 2nd year (Research and development of high-precision self-propelled autonomous assistance system for large farmland); 1999 nendo daikibo nogyo muke seimitsu jiritsu soko sagyo shien system no kaihatsu kenkyu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development is conducted to construct an autonomous system optimum for application to production agriculture. In the development of a mechanical vision-aided navigation sensor, a sensor system is developed and found to be fit for practical application. In the development of a No. 2 robot controller and an automatic steering unit, a controller equipped with a CAN (control area network) interface is built, and found to function normally. As for the navigation of tractors, algorithm for the control of autonomous self-propelled operation and a data transmission control system are developed, and tested. In the GPS (Global Positioning System)-aided mapping of the yields of wheat and potato, mapping algorithm is studied. A fertilizer distributor and a weeder which are operated by instructions from a tractor are tested for behavior, a sensor system is developed to do jobs on the farm, and a database system for farm-related information management is developed. (NEDO)

  6. Achievement report for fiscal 1999 on research and development of technologies for medical welfare equipment. Surgery support system for brain tumors and other conditions (Rationalization for energy profit); 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Noshuyo nado shujutsu shien system (energy shiyo gorika)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    In the second phase of experimental micro-manipulator fabrication, insertion parts equipped with three manipulators and operation input units are built and evaluated. The system comprises three input units and a console with a built-in controller etc., and the console is checked for shape and operability. A high resolution and high brightness stereoscopic viewer is developed for clinical use by surgical operators, and is examined for practicality. The positioning system for the intraoperative vision instrument are improved relative to its attachment method, accuracy, and sterilization tolerance. The result is evaluated, and then further improvement is made. Some functions are added to the surgical planning software program. Software programs are constructed for the real-time control and operation of the viewing system. For the micro-manipulator system to serve as a total system, the forceps are extended, tips are developed for the suction device and incision device, and their functions as members of the system are evaluated. (NEDO)

  7. FY 1999 report on the results of the fundamental investigation for promotion of Joint Implementation. Preliminary evaluation of introduction of VICS systems in Klang Valley and Multimedia Super Corridor in Malaysia; 1999 nendo Malaysia koku Klang Valley oyobi multimedia super corridor ni okeru VICS system donyu no jizen hyoka chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Feasibility study is conducted for introduction of the VICSs (Vehicle Information and Communication Systems) in Malaysia's Klang Valley and Multimedia Super Corridor, to contribute to abatement of the greenhouse effect gases and saving energy. This study has produced the following results. The systems need a total fund of about 1.4 billion yen, including the design fees, when based on the FM multiplex broadcasting, and annual operation/maintenance cost of about 110,000 million yen. These systems are expected to save 4,850 toe/y of fuel and abate CO2 emissions by 11,200 t/y, with the benefit cost ratios of 20.2 toe/million yen and 46.6 tons of CO2/million yen, respectively, when they are in service for 10 years. Introduction of the VICS system in Malaysia is highly feasible both technically and economically, which, however, will need establishment of, e.g., the JICA-proposed integrated traffic information system and Malaysia Traffic Information Authority. (NEDO)

  8. 'Development and introduction of ice water conveyance system and verification of low temperature blast system' for leveling off electric power load; Denryoku fuka heijunka wo misueta 'hyosui hanso hoshiki no kaihatsu donyu to teion sofu hoshiki no kensho'

    Energy Technology Data Exchange (ETDEWEB)

    Kuriyama, T. [Nikken Sekkei Ltd., Osaka (Japan)

    1999-11-05

    From the view point of the earth environment protection, energy-saving in the field of building air-conditioning has become increasingly important. On the other hand, the utilization of nighttime electric power is needed to ease the electric power supply and demand problem, and in this connection, a wider introduction of the ice heat storage system is recommended as one of the means to cope with such a problem. However, the ice heat storage system also has problems to be solved such as energy savability, and economy. Under such circumstances, various technical research and development efforts as well as evaluation thereof have been made centering around the 'technical development of the ice water conveyance system' and the 'evaluation of the low temperature blast system' for energy-saving, facility cost reduction and electric power load leveling off, and as a matter of fact these systems have been installed in actual buildings with useful results. (author)

  9. FY 1999 report on the results of the fundamental investigation for promotion of Joint Implementation. Preliminary evaluation of introduction of VICS systems in Klang Valley and Multimedia Super Corridor in Malaysia; 1999 nendo Malaysia koku Klang Valley oyobi multimedia super corridor ni okeru VICS system donyu no jizen hyoka chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Feasibility study is conducted for introduction of the VICSs (Vehicle Information and Communication Systems) in Malaysia's Klang Valley and Multimedia Super Corridor, to contribute to abatement of the greenhouse effect gases and saving energy. This study has produced the following results. The systems need a total fund of about 1.4 billion yen, including the design fees, when based on the FM multiplex broadcasting, and annual operation/maintenance cost of about 110,000 million yen. These systems are expected to save 4,850 toe/y of fuel and abate CO2 emissions by 11,200 t/y, with the benefit cost ratios of 20.2 toe/million yen and 46.6 tons of CO2/million yen, respectively, when they are in service for 10 years. Introduction of the VICS system in Malaysia is highly feasible both technically and economically, which, however, will need establishment of, e.g., the JICA-proposed integrated traffic information system and Malaysia Traffic Information Authority. (NEDO)

  10. Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Research achievements; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports the achievements in fiscal 1995 in the research and development project for an electronics design and production aid system of simple operation type (MATIC). The project is intended to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. The working group (WG)I, related to automobiles and components thereof, improved functions of the primary system and continued demonstration tests. The group launched for the secondary system a system development that makes timely information transmission and receipt possible among research and development enterprises, local assembly enterprises and facility and parts suppliers. The WGII (household appliances and their parts) designed and developed an electronic catalog system based on pre-prototypes developed independently by different countries, and performed demonstration tests. The WGIII (textiles and apparels) carried out with China demonstration tests on the international EDI system, translation system and CAD/CAM system. It also developed a sewing technology standards system. It installed equipment and devices in Indonesia for preparation of the demonstration tests. (NEDO)

  11. Achievement report for fiscal 1998 on Simple Operation Type CAD/CAM System Development through International Cooperation; 1998 nendo 'kan'i sosagata denshi sekkei seian shien system no kaihatsu ni kansru kenkyu kyoryoku' ni kansuru hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The subject project is implemented in the fields of automobiles and their parts, electrical home appliances and their parts, and textile and apparel. In the field of automobiles and their parts, a prototype is developed of an integrated information management system which is to serve between corporation head offices and assembling businesses overseas, and another prototype is developed of an inter-business technical data serving system which is to serve between overseas assembling businesses and supporting businesses, both involving Japan, Indonesia, and Thailand. In the field of electrical home appliances and their parts, a prototype is developed of an electronic catalog system in a joint endeavor with research institutes of Indonesia, Malaysia, Singapore, and Thailand, and a demonstration test is conducted. A design concurrent engineering system is developed by Japan and Malaysian research institutes. In the field of textile and apparel, prototypes are developed, by Japanese, Chinese, and Indonesian apparel manufactures, of an apparel manufacturing specification system, international EDI (electronic data interchange) system, translation system, and a CAD (computer-aided design)/CAM (computer-aided manufacturing) data interchange system. (NEDO)

  12. Report on simple operation type CAD/CAM system development through international cooperation. Current statuses of Asian countries; 'Kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Asia shokoku no jokyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Information systems, mainly aided by computers, are becoming increasingly important, contributing to development of wide areas of societies and economics, to begin with. However, few developing countries have established sufficient information systems, in spite of their strong desires to do so, which will further widen the gap between them and advanced countries, where these systems are acceleratedly advancing. Given these situations, Center of International Cooperation for Computerization (CICC) has been implementing various projects for providing assistance to and cooperation with oversea countries which are trying to develop information systems. This report summarizes the project, which CICC has been commissioned by NEDO as part of the cooperation programs, for manufacturing technology supported by advanced and integrated information system through international cooperation. It outlines the research cooperation memoranda NEDO has concluded with Indonesia, Malaysia, Singapore and Thailand, and the authorities of China, Indonesia, Malaysia, Singapore and Thailand. (NEDO)

  13. Fiscal 1999 report on basic research for promotion of joint implementation programs. Research on introduction of dual mode bus system for greenhouse gas reduction; 1999 nendo onshitsu koka gas sakugen no tame no dual mode bus system donyu ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A feasibility study is conducted of the above-named system in Malaysia, to be linked to COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) clean development mechanism (CDM). The dual mode bus system (DMBS) is a combination of advantages of the rail running stock such as monorails and the road running stock in that the buses when running on dedicated roads are automatedly formed into a linear formation and travel at a specified economical speed. When running on ordinary roads, the formation is broken into individual buses, and they spread in the town where they travel in a planar pattern. The economical speed and reduction in air drag thanks to the linear formation saves fuel and reduces CO2 emissions. The complementary relationship to be formed with the existing public transportation systems will also function positively. Studies are conducted on condition that two routes be laid in the Kuala Lumpur urban area and one in the new city Putra Jaya. All the three routes exhibit a high economic internal rate of return, but their financial internal rate of return indicates that probabilities are low that they will pay as private businesses. They will need financial supports such as subsidies. Contribution to CO2 reduction may be slight when attention is paid only to the partial changeover from the existing bus system to DMBS but larger contribution will be found in crossover from private cars to DMBS which is higher in quality of service. (NEDO)

  14. FY 1999 report on the results of a feasibility study on a system for producing useful chemical substances by utilizing CO2-containing natural gas fields. II; 1999 nendo CO{sub 2} gan'yu tennen gas den katsuyo ni yoru yuyo kagaku busshitsu seizo system donyu kanosei ni kansuru chosa kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper studied the solar energy use methanol synthesis using CO2 as raw material in the natural gas field with which a large quantity of CO2 is associated. This is a report on the FY 1999 survey. It was found that comparatively many natural gas fields containing CO2 exist also in Asia/Oceania regions. It was also found that when considering the climate and the transportation to Japan, Australia has more advantages in terms of the effective desert area, etc. and is the best site for solar system construction. Various solar concentrating/collecting methods now under development are roughly viewed to extract characteristics and developmental conditions. As to the reforming reaction furnace, it is necessary not only to absorb the world technology, but to develop Japan's original one. The conceptual design and assessment of the system were conducted. About the associated CO2, a limit of the concentration for use was estimated at 25%. In the study of elements of system structure, examined was the thermally combined simulation of heat flow and chemical reaction in the solar heat reaction furnace, and simple models were calculated and subjects were extracted. In a comparison with the conventional methanol synthesis method, this system was found to be excellent in conservation of fossil fuel resources and reduction in CO2 emissions. (NEDO)

  15. Research report for fiscal 1998. Basic research for promoting joint implementation of energy use rationalization in Chinese steel industry (examination of introduction of scrap preheating system for electric furnaces); 1998 nendo chosa hokokusho. Chugoku tekkogyo ni okeru energy no shiyo gorika (denkiro scrap yonetsu system donyu kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Investigations are conducted on a project of introducing a scrap preheating system based on the central insertion movable shaft design into China's electric furnaces for the sake of energy saving and global warming gas reduction. Of the electric furnaces numbering approximately 3400 now in operation in China, most are small and antiquated, and are extremely low in energy efficiency when in operation. The percentage of electricity supplied by coal-fired facilities is high, and this causes the CO2 reduction problem. Investigations are conducted into four steel mills operating electric furnaces, and examinations are made on the applicability of a preheating system, which is the ultimate batch system developed by Nippon Steel Corporation. Studies are conducted for Wuyang Iron and Steel Co., Ltd., Tianjin Steel Pipe Co., Ltd., Budong Iron and Steel Co., Ltd., and Shanghai Five Steel Co., Ltd., and it is found that greenhouse gas will be reduced by 31,000 tons, 21,000 tons, 13,000 tons, and 11,000-tons at the said mills, respectively. It is learned that the cost to be invested will be retrieved in approximately 2.5 years, 2.8 years, 7.7 years, and 8.0 years, respectively. It is concluded that Shanghai Budong Iron and Steel (Group) Co., Ltd., is the best candidate to be equipped with the above-said system. (NEDO)

  16. FY 1998 annual report on the research on the possibility of introducing a usable chemical substance manufacturing system by utilizing natural gas containing CO2; CO{sub 2} gan'yu tennen gas den katsuyo ni yoru yuyo kagaku busshitsu seizo system donyu kanosei ni kansuru chosa kenkyu 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The trends of effective use of gas containing CO2 from natural gas fields are surveyed, and usable chemical substance manufacturing systems which utilize natural energy are investigated, evaluated and analyzed, to extract promising systems for effective use of CO2-containing natural gas and thereby to promote its effective use. Chapter 1 outlines possibility of integrated use of gas containing CO2 from natural gas fields and natural gas energy. Chapter 2 describes the research trends in the CO2 conversion reactions for using unexploited CO2 as the carbon source. Chapter 3 describes natural energy utilization technology applicable to gas containing CO2 from natural gas fields. Chapter 4 describes performance of chemical manufacturing systems utilizing natural gas containing CO2. The energy balances and CO2 emission coefficients are estimated, based on the above. The evaluation is implemented in the order of (1) conventional steam reforming, (2) steam reforming in which heat is supplied by a solar furnace, (3) examination of the exhaust gases from a methanol synthesis process, and (4) examination of CO2-mixed reforming. Chapter 5 describes summary and proposals. (NEDO)

  17. FY 1998 annual report on the research on the possibility of introducing a usable chemical substance manufacturing system by utilizing natural gas containing CO2; CO{sub 2} gan'yu tennen gas den katsuyo ni yoru yuyo kagaku busshitsu seizo system donyu kanosei ni kansuru chosa kenkyu 1998 nendo chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The trends of effective use of gas containing CO2 from natural gas fields are surveyed, and usable chemical substance manufacturing systems which utilize natural energy are investigated, evaluated and analyzed, to extract promising systems for effective use of CO2-containing natural gas and thereby to promote its effective use. Chapter 1 outlines possibility of integrated use of gas containing CO2 from natural gas fields and natural gas energy. Chapter 2 describes the research trends in the CO2 conversion reactions for using unexploited CO2 as the carbon source. Chapter 3 describes natural energy utilization technology applicable to gas containing CO2 from natural gas fields. Chapter 4 describes performance of chemical manufacturing systems utilizing natural gas containing CO2. The energy balances and CO2 emission coefficients are estimated, based on the above. The evaluation is implemented in the order of (1) conventional steam reforming, (2) steam reforming in which heat is supplied by a solar furnace, (3) examination of the exhaust gases from a methanol synthesis process, and (4) examination of CO2-mixed reforming. Chapter 5 describes summary and proposals. (NEDO)

  18. Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Research results; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kenkyu seika

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This 5-year project beginning in FY 1994 is aimed at joint researches with various Asian countries for development of simply operable electronic designs and manufacturing support systems, which supports development of supporting industries (SI) for manufacturing industries in these countries. The project is being implemented in a total of 5 countries, China, Indonesia, Malaysia, Singapore and Thailand, in cooperation with the research institutes with which NEDO has concluded the basic contracts. The following three working groups are established to study construction of the model systems and design these systems for promotion of the joint project in each country; (1) automobiles and their parts, (2) home electric/electronic appliances, and their parts, and (3) textiles and apparels. The FY 1995 project results are described. The working group (1) covers definitions of the business models and conditions for systematizing these models for the demonstration tests. The working group (2) covers development of the electronic catalogues, electronic yellow pages/preproto types, and concurrent engineering. The working group (3) covers the SGML sewing technique specification systems, surveys and utilization tests for network infrastructures, international EDI systems for the textile industry, and translation systems for technical terms of the textile industry. (NEDO)

  19. FY 2000 Immediate-effect type project for research and development for international standards supporting information technology industries. Standardization of the methods of electronic trading of the integrated systems from the designing to production; 2000 nendo joho sangyo shien sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Sekkei kara seizo made no ikkan system no denshiteki torihiki hoho no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at standardization of, e.g., terminology for preparation of the dictionary of the measuring instruments manufactured by the Japan Electric Measuring Instruments Manufacturers' Association (JEMIMA) members, as the first step for realizing the e-Business of the related industry. The FY 2000 efforts are directed to the standardization of terms, classification, description of properties and basic semantic units (BSUs) for making the measuring instruments dictionary including flow meters, thermometers, level meters, meters, wattmeters, indicators, transducers, recorders, temperature transmitters, special instruments for steel making, and so on. Document type definition (DTD) is also standardized for flow meters, thermometers and level meters for information exchange by XML. The applications are also developed for electronic catalog creation support system, electronic catalog registration and revision support system, instrumentation selection support system, and instrumentation retrieval and viewing support system. They are installed in the clients' server systems, to implement the performance tests. Creation/registration and use of the electronic catalogs on the Internet are demonstrated for flow meter, thermometers and level meters. (NEDO)

  20. Report on the FY 1999 research cooperation follow-up project on the development of manufacturing technology supported by advanced and integrated information system through cooperation; 1999 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku follow up jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In FY 1999, the follow-up project was conducted on the development of manufacturing technology supported by advanced and integrated information system through cooperation (MATIC). The project included the grasp of the state of activity, announcement of the achievement, field survey, etc. of China, Indonesia, Malaysia, Singapore and Thailand. China carried out the system development and demonstrative tests in the fiber/apparel field, trying to spread the MATIC system. Indonesia is planning to spread the use of electronic catalog of automotive parts/electronic parts toward small/medium companies through internet. Malaysia was in charge of the development in the field of home electric appliances and demonstrative tests. They use the results so as to meet the demand in the domestic industry, aiming at spreading it in the country. Singapore uses the electronic catalog system to make it apply to the informatization project of the country. Thailand is making efforts for the spread of the MATIC results through the prototype model. (NEDO)

  1. FY 2000 report on the research cooperation project on the research cooperative follow-up for development of the manufacturing technology supported by advanced and integrated information system through cooperation; 2000 nendo kenkyu kyoryoku jigyo. 2000 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku follow up jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The manufacturing technology supported by advanced and integrated information system through cooperation (MATIC), that is, a project supporting the production technology including the international information system and CAD/CAM system, etc. was carried out from FY 1994 to FY 1998. From FY 1999, the follow-up project is being implemented for the spread of the MATIC results, support for the independent R and D and the technical guidance. China, Indonesia, Malaysia and Singapore participated in this project, by which the support and technical guidance were given in three fields: automobiles/the parts; household electric appliances/the parts; fiber/apparel. At present, each country is continuing its own activity for using the system developed in the MATIC project in its country. In this fiscal year, researchers were sent to each country for supporting the activities. Further, the MATIC follow-up committee was established to conduct the drawing-up of a business plan, grasp of the state of the spread/R and D, discussion about problems/subjects, comprehensive evaluation of the MATIC project, etc. (NEDO)

  2. FY 2000 report on the research cooperation project on the research cooperative follow-up for development of the manufacturing technology supported by advanced and integrated information system through cooperation; 2000 nendo kenkyu kyoryoku jigyo. 2000 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku follow up jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The manufacturing technology supported by advanced and integrated information system through cooperation (MATIC), that is, a project supporting the production technology including the international information system and CAD/CAM system, etc. was carried out from FY 1994 to FY 1998. From FY 1999, the follow-up project is being implemented for the spread of the MATIC results, support for the independent R and D and the technical guidance. China, Indonesia, Malaysia and Singapore participated in this project, by which the support and technical guidance were given in three fields: automobiles/the parts; household electric appliances/the parts; fiber/apparel. At present, each country is continuing its own activity for using the system developed in the MATIC project in its country. In this fiscal year, researchers were sent to each country for supporting the activities. Further, the MATIC follow-up committee was established to conduct the drawing-up of a business plan, grasp of the state of the spread/R and D, discussion about problems/subjects, comprehensive evaluation of the MATIC project, etc. (NEDO)

  3. Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Cooperation for joint researches; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Reported herein are the joint research results of the project (manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC)), implemented in China, Indonesia, Malaysia, Singapore and Thailand by Center of International Cooperation for Computerization, commissioned by NEDO. Japan invited researchers from each country to explain the research themes, and discussed construction of the systems in each country. Japanese experts visited the research institutes and cooperative works in these countries, to discuss the research cooperation themes, and survey the conditions and technical levels of these research institutes, and information infrastructures. The oversea researchers were invited to Japan for the MATIC international seminar, discussions for research cooperation themes, and MATIC cooperation promotion committee. Textile and apparel researchers were also invited from China. Japanese experts visited China, Indonesia, Malaysia, Singapore and Thailand for the on-the-spot surveys for each working group. (NEDO)

  4. Fiscal 1998 report on the research cooperation on development of the easy-to-operate electronic design and production support system (Joint research cooperation); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho (kyodo kenkyu kyoryoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Asian countries are constructing information infrastructures actively in spite of severe financial and economic conditions in every country. For promoting advanced manufacturing industries and supporting industries of Asian countries by information technology, the research cooperation promotion project (MATIC) on the electronic design and production support system has been carried out as the joint research project of Japan, China, Indonesia, Malaysia, Singapore and Thailand. This project started as the 5-year project in 1994, and has developed and demonstrated the prototype electronic design and production support system in 3 fields of automobile, home appliance and fiber/apparel. In the final 1998, the R and D and demonstration test were carried out, and the project results were summarized. For discussing the research cooperation concretely with overseas countries, the overseas researchers were invited to Japan for explaining the research state in Japan, confirming the promotion states of each country, and discussing the research report, while Japanese researchers visited the concerned organizations in every country. (NEDO)

  5. Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Cooperation for joint researches; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Reported herein are the joint research results of the project (manufacturing technology supported by advanced and integrated information system through international cooperation (MATIC)), implemented in China, Indonesia, Malaysia, Singapore and Thailand by Center of International Cooperation for Computerization, commissioned by NEDO. Japan invited researchers from each country to explain the research themes, and discussed construction of the systems in each country. Japanese experts visited the research institutes and cooperative works in these countries, to discuss the research cooperation themes, and survey the conditions and technical levels of these research institutes, and information infrastructures. The oversea researchers were invited to Japan for the MATIC international seminar, discussions for research cooperation themes, and MATIC cooperation promotion committee. Textile and apparel researchers were also invited from China. Japanese experts visited China, Indonesia, Malaysia, Singapore and Thailand for the on-the-spot surveys for each working group. (NEDO)

  6. Fiscal 1998 report on the research cooperation on development of the easy-to-operate electronic design and production support system (Joint research cooperation); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho (kyodo kenkyu kyoryoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Asian countries are constructing information infrastructures actively in spite of severe financial and economic conditions in every country. For promoting advanced manufacturing industries and supporting industries of Asian countries by information technology, the research cooperation promotion project (MATIC) on the electronic design and production support system has been carried out as the joint research project of Japan, China, Indonesia, Malaysia, Singapore and Thailand. This project started as the 5-year project in 1994, and has developed and demonstrated the prototype electronic design and production support system in 3 fields of automobile, home appliance and fiber/apparel. In the final 1998, the R and D and demonstration test were carried out, and the project results were summarized. For discussing the research cooperation concretely with overseas countries, the overseas researchers were invited to Japan for explaining the research state in Japan, confirming the promotion states of each country, and discussing the research report, while Japanese researchers visited the concerned organizations in every country. (NEDO)

  7. Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This paper reports the committee activities in fiscal 1995 on research cooperation for developing an electronics design and production aid system of simple operation type (MATIC). This fiscal year has decided the directionality of MATIC promotion by activities carried out by the different committees. These activities relate to research and development themes, the basic policies of the research and development along with the themes, research and development themes linked with overseas countries, and promotion methods. The working group (WG)I has discussed and deliberated specific research and development items to promote research and development of automobiles and components thereof as the promotion theme, promotion of the research and development, and technical problems. The committee consists of researchers at the related corporations participated in MATIC. The WGII has taken up household appliances and parts thereof, and the WGIII textiles and apparels as the research and development themes, and given specific discussions for promoting the research and development. The paper also reports the activities taken by different committees for promotion of the production-based futuristic type integrated information system, and promotion of the MATIC technologies, operation and cooperation. (NEDO)

  8. Achievement report for fiscal 1998. Research and development project of regional consortiums (energy field in the regional consortiums / research and development of a precise autonomous operating system for large-scale farm use (the first year)); 1998 nendo chiiki consortium energy bun'ya. Daikibo nogyo muke seimitsu jiritsu soko sagyo shien system no kenkyu kaihatsu (dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A precise autonomous operating system is under development to commercialize new agricultural tractors that make possible the stable and safe food supply in Hokkaido in the future as the Japan's food base, and meet the regional needs. This paper describes the development achievements during fiscal 1998. A highly precise and robust automatic driving algorithm was developed by adopting RTK-GPS as a navigation sensor, optical fiber gyroscope and machine vision to have them perform active sensor fusion. Autonomous operation was possible with an error of about 15 cm at a speed as high as 3 m/s. Development and prototype fabrication were carried out on a prototype of the precision fertilizer application machine using GPS precise spatial mapping for farm fields, and a precision weeder. In developing the crawler type autonomous vehicle, the obstacle detecting method, the communication system between the base station and the mobile station, and the specifications of the working machine were established. A yield sensor, soil sensing and pasture sensing were discussed, and a method for collecting information required for precise work was proposed. Market size for agricultural machines in Hokkaido was investigated, and trends in America were analyzed. (NEDO)

  9. Report on research cooperation for developing a simple operation type electronics design and production supporting system in fiscal 1998 (committee activity report); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research cooperation is being promoted on a simple operation type electronics design and production supporting information system to assist the information using efforts in Asian countries. The cooperation is made jointly with five countries, namely, China, Indonesia, Malaysia, Singapore and Thailand. Fiscal 1998, falling under the final fiscal year, summarized the achievements and the committee activities. In order to promote research and development of automobiles and the components thereof, the WG-I, composed of committee members having professional knowledge, has deliberated specific research and development items, promotion of the research and development, technical problems, and promotion of joint research and development with other countries. The WG-II has made similar discussions on household electric appliances and the components thereof. The MATIC technical committee is composed of chiefs of the working groups and the responsible persons for system development. The committee discussed technical problems common to the working groups in promoting the projects, and made deliberations and adjustments on methods for promoting the research cooperation among the overseas countries. The cooperation promoting committee is composed of Japanese researchers and representatives of research institutes in other countries, and discussed how to move forward and adjust the research cooperation themes. (NEDO)

  10. Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports the research and development project for an electronics design and production aid system of simple operation type. The project (MATIC) has been executed to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. Fiscal 1997 has entered full-fledged demonstration experiments, and decided the project directionality as a result of different committee activities as to policies, contents and promotion methods for research, development and demonstration experiments. The working group (WG) 1, composed of members having professional knowledge on automobiles and components thereof, has deliberated specific research and development items, promotion of the research and development, technical problems, promotion of joint researches with overseas countries. The WG II, composed of members having professional knowledge on household electric appliances and their parts, discussed promotion of research and development of household electric appliances and their parts. The WG III, composed of textile and apparel expertise members, made attempts in promoting the research and development of household electrid appliances and their parts. This paper describes other committee activities including promotion of operation and cooperation on production-based futuristic type integrated information system and MATIC technologies. (NEDO)

  11. Report for fiscal 1995 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1995 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This paper reports the committee activities in fiscal 1995 on research cooperation for developing an electronics design and production aid system of simple operation type (MATIC). This fiscal year has decided the directionality of MATIC promotion by activities carried out by the different committees. These activities relate to research and development themes, the basic policies of the research and development along with the themes, research and development themes linked with overseas countries, and promotion methods. The working group (WG)I has discussed and deliberated specific research and development items to promote research and development of automobiles and components thereof as the promotion theme, promotion of the research and development, and technical problems. The committee consists of researchers at the related corporations participated in MATIC. The WGII has taken up household appliances and parts thereof, and the WGIII textiles and apparels as the research and development themes, and given specific discussions for promoting the research and development. The paper also reports the activities taken by different committees for promotion of the production-based futuristic type integrated information system, and promotion of the MATIC technologies, operation and cooperation. (NEDO)

  12. Achievement report for fiscal 1998. Research and development project of regional consortiums (energy field in the regional consortiums / research and development of a precise autonomous operating system for large-scale farm use (the first year)); 1998 nendo chiiki consortium energy bun'ya. Daikibo nogyo muke seimitsu jiritsu soko sagyo shien system no kenkyu kaihatsu (dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A precise autonomous operating system is under development to commercialize new agricultural tractors that make possible the stable and safe food supply in Hokkaido in the future as the Japan's food base, and meet the regional needs. This paper describes the development achievements during fiscal 1998. A highly precise and robust automatic driving algorithm was developed by adopting RTK-GPS as a navigation sensor, optical fiber gyroscope and machine vision to have them perform active sensor fusion. Autonomous operation was possible with an error of about 15 cm at a speed as high as 3 m/s. Development and prototype fabrication were carried out on a prototype of the precision fertilizer application machine using GPS precise spatial mapping for farm fields, and a precision weeder. In developing the crawler type autonomous vehicle, the obstacle detecting method, the communication system between the base station and the mobile station, and the specifications of the working machine were established. A yield sensor, soil sensing and pasture sensing were discussed, and a method for collecting information required for precise work was proposed. Market size for agricultural machines in Hokkaido was investigated, and trends in America were analyzed. (NEDO)

  13. Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Committee activity record; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports the research and development project for an electronics design and production aid system of simple operation type. The project (MATIC) has been executed to support works of Asian countries on the information society, and enhance levels of the manufacturing industries and supportive industries by utilizing the information technologies. Fiscal 1997 has entered full-fledged demonstration experiments, and decided the project directionality as a result of different committee activities as to policies, contents and promotion methods for research, development and demonstration experiments. The working group (WG) 1, composed of members having professional knowledge on automobiles and components thereof, has deliberated specific research and development items, promotion of the research and development, technical problems, promotion of joint researches with overseas countries. The WG II, composed of members having professional knowledge on household electric appliances and their parts, discussed promotion of research and development of household electric appliances and their parts. The WG III, composed of textile and apparel expertise members, made attempts in promoting the research and development of household electrid appliances and their parts. This paper describes other committee activities including promotion of operation and cooperation on production-based futuristic type integrated information system and MATIC technologies. (NEDO)

  14. Report on research cooperation for developing a simple operation type electronics design and production supporting system in fiscal 1998 (committee activity report); 1998 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Iinkai katsudo kiroku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research cooperation is being promoted on a simple operation type electronics design and production supporting information system to assist the information using efforts in Asian countries. The cooperation is made jointly with five countries, namely, China, Indonesia, Malaysia, Singapore and Thailand. Fiscal 1998, falling under the final fiscal year, summarized the achievements and the committee activities. In order to promote research and development of automobiles and the components thereof, the WG-I, composed of committee members having professional knowledge, has deliberated specific research and development items, promotion of the research and development, technical problems, and promotion of joint research and development with other countries. The WG-II has made similar discussions on household electric appliances and the components thereof. The MATIC technical committee is composed of chiefs of the working groups and the responsible persons for system development. The committee discussed technical problems common to the working groups in promoting the projects, and made deliberations and adjustments on methods for promoting the research cooperation among the overseas countries. The cooperation promoting committee is composed of Japanese researchers and representatives of research institutes in other countries, and discussed how to move forward and adjust the research cooperation themes. (NEDO)

  15. Report for fiscal 1998 on Simple Operation Type CAD/CAM System Development through International Cooperation. Report on the achievements of counterparts overseas; 1998 nendo 'kan'i sosagata denshi sekkei seian shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kaigai counter part seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Concerning the subject matter, achievements of China, Indonesia, Malaysia, Singapore, and Thailand are reported. In China, a technical data transfer process is under development, designed to serve between CAD (computer-aided design)/CAM (computer-aided manufacturing) packages of different file formats. In Indonesia, WG1 activities are being conducted with the assistance of Toyota Motor Corporation, and WG3 activities with the assistance of Wacoal Corporation, Japan. In Malaysia, designing, development, and tests are under way for prototype systems of an electronic catalog, direct link to CAD/CAM, transfer and sharing of electronic manufacturing data, etc., all to be completed by March 1999. In Singapore, an electronic parts library is compiled, and a verification test is conducted involving response time, download time, etc. In Thailand, development is under way of an engineering browser, automobile industry-oriented WEB-based information center, etc. (NEDO)

  16. Report for fiscal 1998 on Simple Operation Type CAD/CAM System Development through International Cooperation. Report on the achievements of counterparts overseas; 1998 nendo 'kan'i sosagata denshi sekkei seian shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kaigai counter part seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Concerning the subject matter, achievements of China, Indonesia, Malaysia, Singapore, and Thailand are reported. In China, a technical data transfer process is under development, designed to serve between CAD (computer-aided design)/CAM (computer-aided manufacturing) packages of different file formats. In Indonesia, WG1 activities are being conducted with the assistance of Toyota Motor Corporation, and WG3 activities with the assistance of Wacoal Corporation, Japan. In Malaysia, designing, development, and tests are under way for prototype systems of an electronic catalog, direct link to CAD/CAM, transfer and sharing of electronic manufacturing data, etc., all to be completed by March 1999. In Singapore, an electronic parts library is compiled, and a verification test is conducted involving response time, download time, etc. In Thailand, development is under way of an engineering browser, automobile industry-oriented WEB-based information center, etc. (NEDO)

  17. Report on results concerning development of supermetal technology, R and D of offshore oil production supporting system, and development of technology for aluminum-based high-anticorrosive microstructured metallic material (FY2000); Super metal no gijutsu kaihatsu seika hokokusho (2000 nendo). Kaitei sekiyu seisan shien system kenkyu kaihatsu (Aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With the purpose of developing high strength and high-anticorrosive aluminum-based material through microstructure control, R and D was conducted, with fiscal 2000 results compiled. In the research of grain refinement mechanism, molten metal rolled stock was experimentally produced in which Mg content was varied 0-2.5 mass % with Al-2.5 mass % Mn as its base. As a result, a microstructure with an average grain size of about 3 {mu}m was obtained by processing the alloy through homogenization at 550 degrees C, cold rolling by 91% and the final treatment at 350 degrees C without Mg addition. Addition of Mg increased square grain boundaries in the microstructure, raising proof stress to about 180 MPa in Al-2.5%Mn-2.5%Mg alloy. In the research of development of the machining process, a rapid heating process was performed on a typical aluminum alloy, with the effect examined, by an alloy system or a plate thickness, on the electric power used and on the temperature reached. A rapidly heated aluminum alloy plate turned to have a microstructure with equi-axed grains of a uniform size, compared with a salt bath processed material heated at the same temperature. (NEDO)

  18. Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Joint research cooperation; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This report describes Japan's joint researches with China, Indonesia, Malaysia, Singapore, and Thailand under the above-named project (MATIC) which were carried out in fiscal 1997. Scientists are invited to Japan from the above-named countries, to whom Japan's status of researches is explained and with whom discussion is conducted about progress in general and system development in those countries, and about verification tests. Japanese scientists visit research institutes of those countries so as to appraise the progress of researches and technological levels and to install computers for verification tests. Scientists visiting this country upon Japan's invitation and workshop held in Japan are enumerated below. Accepted by Working Group I (automobile and parts) are scientists from Indonesia and China and workshops from two countries; accepted by Working Group II (electrical home appliance) are scientists from Malaysia and workshops from five countries and then from four countries; and accepted by Working Group III (fiber and apparel) are scientists from China. Visits are made by the Working Groups to Thailand, Indonesia, Malaysia, Singapore, and China. (NEDO)

  19. Report for fiscal 1997 on simple operation type CAD/CAM system development through international cooperation. Joint research cooperation; 1997 nendo 'kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku' ni kansuru hokokusho. Kyodo kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This report describes Japan's joint researches with China, Indonesia, Malaysia, Singapore, and Thailand under the above-named project (MATIC) which were carried out in fiscal 1997. Scientists are invited to Japan from the above-named countries, to whom Japan's status of researches is explained and with whom discussion is conducted about progress in general and system development in those countries, and about verification tests. Japanese scientists visit research institutes of those countries so as to appraise the progress of researches and technological levels and to install computers for verification tests. Scientists visiting this country upon Japan's invitation and workshop held in Japan are enumerated below. Accepted by Working Group I (automobile and parts) are scientists from Indonesia and China and workshops from two countries; accepted by Working Group II (electrical home appliance) are scientists from Malaysia and workshops from five countries and then from four countries; and accepted by Working Group III (fiber and apparel) are scientists from China. Visits are made by the Working Groups to Thailand, Indonesia, Malaysia, Singapore, and China. (NEDO)

  20. Fiscal 1998 survey report. Medical equipment (Development of fine sampling/analysis system for blood / Development of high-precision 3-D image diagnosis system / Development of low-invasion operation support system / Total development of artificial internal organ technologies); 1998 nendo chosa hokokusho. Iryo kiki (ketsuekinado biryo saishu, biryo bunseki system kaihatsu/koseido sanjigen eizo shindan system kaihatsu/teishinshu shujutsu shien system kaihatsu/jinko zoki gijutsu sogo kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For efficient medical care supply systems, the R and D of advanced medical care technology and equipment largely contribute to productivity improvement for medical care services. Among them, a progress of medical care technology is becoming important for preparation of efficient and fair supply systems. MITI thus established 'Medical care and welfare equipment development project' in 1994, and has promoted the strategic long-term R and D project of medical care and welfare equipment as joint R and D project of NEDO and private enterprises. In fiscal 1998, on the development of the fine sampling/analysis system for blood, the high- precision 3-D image diagnosis system, the low-invasion operation support system, and the artificial internal organ technologies since fiscal 1996, this project clarified essential technical issues based on the future view, selected some themes to be newly developed in the future, and surveyed and evaluated the details of their R and D concretely. (NEDO)

  1. Project to support promotion of forming an environmentally friendly energy community. Survey report on 'a survey on introduction of an RDF electric power generation system utilizing general wastes in the Noto area'; Kankyo chowagata energy community keisei sokushin hojo jigyo. 'Noto chiiki ni okeru ippan haikibutsu riyo RDF hatsuden no donyu ni kansuru chosa' chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A business feasibility survey was performed on introduction of an RDF electric power generation system utilizing general wastes in the Noto area. Wastes quantity was estimated by accounting for large-sized wastes to be generated newly as a result of enforcement of the container package recycling law, and transfer of non-combustible wastes to incineration. The quantity was estimated to be 84,000 tons annually. Quantities of RDF and heat were calculated from this estimation to be 103 tons per day and 400 lkcal/kg respectively. According to the result of discussing the RDF transportation systems, time-based freight was found advantageous for short distance, and distance freight system for long distance in terms of cost. Discussions for RDF power systems were carried out on an RDF circulation fluid bed furnace plus ash melting furnace, a fluid bed gasification melting furnace, and shaft furnace type gasification melting furnace. In a comprehensive view, it is difficult to distinguish them in terms of merit and demerit. Molten slag was assumed to be re-utilized, but cost for the re-utilization should be considered. According to the result of discussing the business feasibility, it was found difficult to make it profitable by operating the RDF power generation business alone, and wastes incineration charge should be collected. (NEDO)

  2. Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education - iron and steel (Survey on education accreditation in material field); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (tekko) -Zairyo bunya ni okeru kyoiku nintei ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, a survey was performed on external accreditation systems for engineer education such as in universities and other organizations in the material field. In the survey, discussions were given on whether or not the education program accreditation system for the material field being structured has any problem in the actual operation of the accreditation through trials at Chiba Engineering University and Tokai University. As a result, it was revealed that the criteria are too general, requiring more detailed description on the guideline, and criteria should be so considered that assessment at higher levels can be given to the graduation research, which is a Japan's particular education system. In addition, it was made clear as a problem in the education programming side that a room for improvement remains in the education methods for the engineering ethics, communication skills, and the method for evaluating the students' achievements. In the survey on the methods for examination and accreditation in the U.S.A. it was found out that education organizations are perplexed with the new criteria of EC 2000. (NEDO)

  3. FY 1999 report on the results of the superconductive energy application technology development/research on a total system, etc. Survey of potentiality of the commercialization of superconductive technology, effects of the introduction, etc. (Future course of the superconductive technology development in Japan); 1999 nendo chodendo denryoku oryokuyo gijutsu kaihatsu total system nado no kenkyu. Chodendo gijutsu no jitsuyoka kanosei oyobi donyu koka nado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    By the use of superconductive technology, the following are aimed at: marked reduction in power loss of electrical equipment and power transmission path, and size/weight reduction in electrical devices by high current/magnetic flux density. The superconductive technology has advantages such as great energy saving effect, CO2 reduction and global environmental preservation. As an example, concerning the superconductive generator now being developed under the New Sunshine Project, power loss can be reduced by half, and by the use of high magnetic field, size/weight can be reduced such as reduction in rotor diameter and reduction in weight by half. Further, as an innovative system, cited are the superconducting magnetic energy storage system (SMES) and flywheel energy storage system. The superconducting magnetic levitation railway, medical use MRI, etc. have also innovativity which is difficult to get in the conventional technology. Effects are also expected of introducing the process development using superconducting magnet such as magnetic separation, electromagnetic metallurgy, electromagnetic agitation and monocrytal growth convection control. Also cited is Josephson electronic device. High performance SQUID in bio-magnetic/non-destructive inspection is also expected to be developed. (NEDO)

  4. FY 2001 report on the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Potential survey of the introduction of a processing/power generation system using ASR in the South region of Tochigi Prefecture; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Tochigi ken nanbu chiiki ni okeru ASR (Shuredda dust) wo nenryo to shita shori hatsuden system no donyu kanosei chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the consistent processing of waste automobile in Tochigi Prefecture and the neighboring area, survey/study were made of the thermal recycle using shredder dust, ASR (automobile shredder residue), as fuel as well as the material recycle. As to the amount of material recycle of waste automobile, the amount of potential recycle of iron, copper, plastic, etc. was estimated, and it was found out that the potential recycle of parts such as engine was 40-45%, that of iron scrap 35-40%, and that of ASR 20-25%. The amount of fuel (ASR amount) to be thrown into the gasification power generation system was set up at 150t. As the gasification power generation system, the pyrolysis gasifier and shaft kiln gasification melting furnace were selected. In the study of economical efficiency of the gasification power generation system, the following were considered: ASR processing price, plant cost, subsidy, running cost, char receiving price, power selling price, etc., but even in the case of the pyrolysis gasifier with highest valuation, both payback years and IRR did not reach the target. (NEDO)

  5. FY 1998 result report. Study of a total system for the development of superconductor power application technology (Feasibility study of commercialization of superconductivity technology and study of the introductory effect. Future superconductivity technology development in Japan); 1998 nendo seika hokokusho. Chodendo denryoku oyo gijutsu kaihatsu total system nado no kenkyu chodendo gijutsu no jitsuyoka kanosei oyobi donyu kokanado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As a part of the New Sunshine Project, 'an R and D project on superconductor power application technology,' an examinational study was made as a mini project to clarify the developmental course for commercialization of superconductor technology. The superconductor technology is being watched with interest as a technology in the 21st century. In the application to the electric power/energy field, in particular, expected are the energy saving effect by high operation efficiency, excellent environmentality, developmental potentiality of new equipment/system by the application of ferromagnetism, etc. Accordingly, the paper analytically arranged the needs of superconductor devices in Japan and abroad and the technology seeds corresponding to the needs, and prepared the developmental subjects of superconductor technology. These developmental steps and the mutual relationship were expressed in an R and D framework. At the same time, as to the superconductivity, a survey outlined the projects carried out in each government office in Japan. The future developmental course was indicated, and proposals were made on the equipment/system as object which are the subjects for urgent development for commercialization. (NEDO)

  6. FY 1998 result report. Study of a total system for the development of superconductor power application technology (Feasibility study of commercialization of superconductivity technology and study of the introductory effect. Future superconductivity technology development in Japan); 1998 nendo seika hokokusho. Chodendo denryoku oyo gijutsu kaihatsu total system nado no kenkyu chodendo gijutsu no jitsuyoka kanosei oyobi donyu kokanado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    As a part of the New Sunshine Project, 'an R and D project on superconductor power application technology,' an examinational study was made as a mini project to clarify the developmental course for commercialization of superconductor technology. The superconductor technology is being watched with interest as a technology in the 21st century. In the application to the electric power/energy field, in particular, expected are the energy saving effect by high operation efficiency, excellent environmentality, developmental potentiality of new equipment/system by the application of ferromagnetism, etc. Accordingly, the paper analytically arranged the needs of superconductor devices in Japan and abroad and the technology seeds corresponding to the needs, and prepared the developmental subjects of superconductor technology. These developmental steps and the mutual relationship were expressed in an R and D framework. At the same time, as to the superconductivity, a survey outlined the projects carried out in each government office in Japan. The future developmental course was indicated, and proposals were made on the equipment/system as object which are the subjects for urgent development for commercialization. (NEDO)

  7. Effect of groupware introduction on office works; Groupware donyu no white color gyomu e ataeru eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Baba, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-05-01

    Investments for information systems in Japanese firms have been shifting from those for main frame systems to PC, LAN and groupware systems. Described herein are effects of groupware introduction on office works, and efficient introduction and practical application of these systems. The groupware functions are divided into information sharing, analyzing, integrating and coordinating functions, and changed information transmission as a result of practical application of each function has been followed by literature and questionnaire surveys on experiences at advanced enterprises. The results indicate that the changes are represented by 6 patterns, from replacement of information media to changes in working styles. The major productivity-related effects brought by introduction of these systems are decreased document volumes and improved skills of employees. The notable effects on office works are improved efficiency resulting from allotting one personal computer to each employee and from introduction of E-mail systems which solve problems involved in telephone communication. 15 refs., 11 figs., 10 tabs.

  8. Guidebook for introduction of snow/ice cool energy; Seppyo reinetsu energy donyu guide book

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of contributing to the promotion of introduction of snow/ice cool energy in cold snowing areas, investigational study was made such as analysis of samples of introduction of snow/ice cool energy and effects. In the survey, for three kinds of the snow/ice cool energy system, that is, snow air-conditioning/refrigerating system, ice shelter system and artificial frozen soil system (heat pipe), each of the samples of introduction was outlined, and the effect of introduction by system was analyzed. As to the evaluation of economical efficiency, constructed were 12 kinds of the snow/ice cool energy spread type model system by the demand facilities including distribution facilities of perishable foods and shopping centers, hospitals and multiple dwelling houses, commercial/residential facilities such as office buildings, and industrial facilities such as food factories. These was comparatively studied with the electric air-conditioning system. As a result, it was made clear that the total cost was approximately a half times as high as that of the electric air-conditioning system, but the system had great incentive effect, supported by subsidies for the initial investment. (NEDO)

  9. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. Third year report. Development of precision farming system combined with the autonomous vehicle for large scale agriculture; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Daikibo nogyo muke seimitsu jiritsu soko sagyo shien system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A farming supporting system that enables autonomous driving was developed from a viewpoint that the development of super manpower saving technology including automation helps sustainable development of the Japanese agriculture. The following were conducted: development of autonomous driving vehicle, development of automated operation unit, field space mapping for precision agriculture and development of groups of PF (precision farming) work machine (weeder, controller, fertilizer applicator, harvesting machine), development of groups of field work sensor (simple soil analytical system, crop growing sensor, glass yield sensor), development of field information managing database, development of work optimized application software. The operation test on the integration system was made at the model production field. The operation experiment using fertilizer applicator, controller and autonomous driving tractor was carried out at a beet field of 2ha in the farming zone in Tokachi, Hokkaido, and the results were obtained as expected. Further, as to the precision agriculture introduced with developmental equipment, etc., 20% of the energy consumption is expected to be reduced. (NEDO)

  10. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. Third year report. Development of precision farming system combined with the autonomous vehicle for large scale agriculture; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Daikibo nogyo muke seimitsu jiritsu soko sagyo shien system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A farming supporting system that enables autonomous driving was developed from a viewpoint that the development of super manpower saving technology including automation helps sustainable development of the Japanese agriculture. The following were conducted: development of autonomous driving vehicle, development of automated operation unit, field space mapping for precision agriculture and development of groups of PF (precision farming) work machine (weeder, controller, fertilizer applicator, harvesting machine), development of groups of field work sensor (simple soil analytical system, crop growing sensor, glass yield sensor), development of field information managing database, development of work optimized application software. The operation test on the integration system was made at the model production field. The operation experiment using fertilizer applicator, controller and autonomous driving tractor was carried out at a beet field of 2ha in the farming zone in Tokachi, Hokkaido, and the results were obtained as expected. Further, as to the precision agriculture introduced with developmental equipment, etc., 20% of the energy consumption is expected to be reduced. (NEDO)

  11. Wastes power generation introduction manual. Main edition; Haikibutsu hatsuden donyu manual. Honpen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A practical and specific working manual was prepared that satisfies the standards and criteria defined in the relevant law such as the Sanitation and Environment Ordinance No. 249, the guideline for generation of dioxins caused by refuse disposal, and that enables the reports evaluating the wastes quantitatively to be submitted to heads of the local governments when persons in charge of planning the introduction of wastes power generation at local governments discuss the wastes power generation systems. Taking general combustible wastes and sewage sludge treatments as the object, this paper details from the economic performance to size of wastes treatment at the priority limit for the power generation facility introduction. The subject power generation systems include the following: the stoker furnace/separation type ash melting furnace power generation system, the fluidized bed/separation type ash melting furnace power generation system, and the direct type gasification melting furnace power generation system, whose establishment of safety, reliability and stability have been verified by full-size system operation record available at the local governments, the gas turbine re-powering composite type power generation system (gas turbine power plants are installed beside the incineration furnaces) that makes high-efficiency power generation possible, and the RDF power generation system (power generation by mixed combustion with general refuses, and power generation using RDF (refuse derived fuel) exclusive combustion). Other important discussion and assessment items include environment and resource utilization performances. (NEDO)

  12. Programs for promoting new energy introduction into Wakkanai City; Wakkanaishi shin energy donyu sokushin keikaku keikakusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The average temperature in the summer season at Wakkanai is 19 degrees C, and below zero degrees C in the winter season. Solar radiation duration is shorter in November through February due partly to the presence of snow. In terms of total solar radiation amount, the city occupies a middling position in the whole Hokkaido island. As for the force of the wind, a daily maximum wind velocity of 10m/s or stronger occur on 8 to 10 days every month in the period October through May. As projects for promoting new energy introduction, the below-named ones are chosen and subjected to examination for feasibility. They are a wind power generation system for a water purification plant; a district heating system utilizing cogeneration at the city middle sector; a hybrid system of methane fermentation and wind power generation for a public stock-rearing farm; a hybrid system of cogeneration and photovoltaic power generation for Fujimi district accommodation facilities; and photovoltaic power generation as a clean energy introduction system for a general gymnastic hall of Wakkanai City. Since the above-named subjects are all excellent in economy and environmentally-friendliness, it is suggested that efforts be exerted to realize them. (NEDO)

  13. Guidebook for introducing the photovoltaic power generation; Taiyoko hatsuden donyu guidebook

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-01

    Recently the number of installation of the photovoltaic power system has been increasing. At present, the estimated introduction amount is 70,000-80,000 kW, which is still big in difference with the targeted introduction value. As seen in the increase in the number of installation, the trend toward the introduction is increasing, but there are left problems on the introduction such as 'the cost is high,' 'the information on the installation has not been well known.' Also in future, it is necessary to further promote the installation, tackling factors to hinder the introduction and making efforts to prepare for the introduction environment. In consideration of such background, in this guidebook, the items required when local governmental organizations, business operators, etc. study the introduction of photovoltaic power system were arranged. Also arranged were the outline and introduction samples of photovoltaic power system, general information on the introduction of the subsidy system, etc., procedures of planning/design, how to concretely introduce the related rules, various procedures to be taken, etc. For reference, the guidebook includes drawings of samples, data on the test field projects which have been carried out so far, data on solar radiation, etc. It is expected that the guidebook will be a help to the understanding of the photovoltaic power generation and will connect to further promotion of the introduction. (NEDO)

  14. Guidebook for introducing the photovoltaic power generation; Taiyoko hatsuden donyu guidebook

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-01

    Recently the number of installation of the photovoltaic power system has been increasing. At present, the estimated introduction amount is 70,000-80,000 kW, which is still big in difference with the targeted introduction value. As seen in the increase in the number of installation, the trend toward the introduction is increasing, but there are left problems on the introduction such as 'the cost is high,' 'the information on the installation has not been well known.' Also in future, it is necessary to further promote the installation, tackling factors to hinder the introduction and making efforts to prepare for the introduction environment. In consideration of such background, in this guidebook, the items required when local governmental organizations, business operators, etc. study the introduction of photovoltaic power system were arranged. Also arranged were the outline and introduction samples of photovoltaic power system, general information on the introduction of the subsidy system, etc., procedures of planning/design, how to concretely introduce the related rules, various procedures to be taken, etc. For reference, the guidebook includes drawings of samples, data on the test field projects which have been carried out so far, data on solar radiation, etc. It is expected that the guidebook will be a help to the understanding of the photovoltaic power generation and will connect to further promotion of the introduction. (NEDO)

  15. Introduction guide book for wind power generation; Furyoku hatsuden donyu guide book

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper arranges essential items for introduction of wind power generation to local governments. Natural wind power energy which is free from emission of atmospheric pollutants such as CO2 and probably profitable, is leading regenerative energy among several new energies, and its rapid diffusion is expected. At the end of 1995, a wind power generation facility capacity amounts to 4900MW in the world, 1770MW in USA, 1140MW in Germany, 630MW in Denmark, 550MW in India, and 250MW in the Netherlands. In Japan, its introduction to local governments is in progress with preparation of a purchase system of surplus electric power and a system interconnection guideline. A total facility capacity reached 10MW in 1996, and is scheduled to reach 150MW in fiscal 2010. NEDO`s wind characteristic map of Japan shows many promising areas for power generation. Since these information is not yet well known, the following are summarized: the present state, features of wind condition, power generation systems, application cases, an approach to survey research, construction, maintenance and related laws, and a subsidy system. 31 refs., 48 figs., 40 tabs.

  16. Feasibility study on the introduction of hybrid buses; Hybrid bus donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose of this research is to design pilot projects for introducing hybrid buses into the public transportation sector. This research also covers contents regarding hybrid buses with a trolley-collector motor and a diesel engine, to identify technical and economical problems and to analyze cost beneficiation using hybrid buses. The trolley parallel hybrid system has been employed for the feasibility study. This system has abundant operation results in Europe and the USA. Its battery is small or is not necessary, and the maintenance cost is also low. As a result of the feasibility study, reduction effects of CO2 emission were found out. When the CO2 generation at the power plant is not counted, the reduction effect was estimated to be 32% compared with the CO2 emission from diesel buses. When the CO2 generation at the power plant is considered, it was estimated to be 18%. The cost beneficiation was investigated for the cases of the transportations using trolley system surrounding a medium-scale terminal among large-scale housing development, tourist resort, and stations. The annual income is estimated to be larger than the annual payment in each case. It was found that the hybrid bus is economically established. 17 refs., 48 figs., 41 tabs.

  17. CIM overview. (2). ; Architecture, infrastructure, information technology. CIM soron. (2). ; Architecture, infra, joho riyo shien gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Seryo, K [IBM Japan Ltd., Tokyo (Japan)

    1991-12-10

    The materialization of computer integrated manufacturing (CIM) requires an establishment of its systematizing system, i.e., architecturer and planning of the infrastructure to support it and basic engineering to support the informational utilization. The CIM architecture is classified into management and system structure, strategic planning method, System development introduction method, etc. The infrastructure aims at epoch-makingly heightening the productivity and speed by integrating the production planning, engineering design, accounting, sales, general business and affairs, production engineering, production activities, and activities of suppliers and clients. The informational utilization support engineering comprises the management support tool, decision making support tool, application development tool, etc. What is important is to establish a system of systematizing engineering in order not to be behind the strategic activation era of information to come. 17 refs., 4 figs., 1 tab.

  18. FY1995 community support by mobile agents; 1995 nendo mobile agent ni yoru community keisei shien

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The purpose is to develop fundamental technologies for navigation systems and mobile computing systems in museums, theme parks and cities. Concretely, we implement software agents into the mobile computing environment which consists of PHS, mobile computers and mobile robots, and realize various functions to access regional information. We have studied on Communityware which supports human activities and communities by using mobile agents implemented into mobile computers and town robots. The mobile agents, which intelligently process information obtained in physical and virtual worlds, access regional information which is omnipresent in the environment. With respect to the approach using mobile computers, we have provided one hundred mobile computers in the international conference on multiagent systems 1996 and carried out the first experimentation of mobile computing in the world. The mobile computer has two functions: Community Viewer which displays interactions between members of communities and Social Matchmaker which supports to hold meetings by searching for people who have common interests. With respect to the approach using town robots, we have developed a robot system which can robustly behave in a complex outdoor environment by using vision agents embedded in the environment. The system aims at support of people in streets. (NEDO)

  19. Wastes power generation introduction manual. Material edition; Haikibutsu hatsuden donyu manual. Shiryohen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    This paper collects and puts into order the materials used in preparing the manual. The materials were classified into the power generation system database related to discussion of the economic performance, case studies, technical materials, other referential materials and glossary. The database shows power generation efficiency, auxiliary power ratio, construction cost, utility cost and number of operators. The case studies present examples of economy calculations on the five recommended power generation systems at a wastes treatment capacity of 180 tons a day. Technical materials put into order the technological discussions on efficiency improvement, environmental measures (suppression of discharge of dioxins, measures for their removal, and the effects thereof), refuse derived fuel (RDF) and power plant operating techniques. The other referential materials collect laws, notifications, and guidelines related to the Welfare Ministry, laws, notifications, criteria and related to the Ministry of International Trade and Industry, and materials related to LCA, forms of power generation business entities, general wastes disposal business, and electric business bonds. The glossary explains terms required for operation and understanding of the manual. (NEDO)

  20. 17th Symposium of NEDO projects. Introducing/spreading project subcommittee; Donyu fukyu jigyo bunkakai. Dai 17kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    The results of the following themes are presented in this subcommittee; (1) outline of the new energy introduction promotion department, (2) the project results, and (3) introduction of the examples. For the theme (1), NEDO is supporting the projects for introducing and promoting new energy systems, feasibility studies for introduction of these systems, and field test (FT) projects to accumulate the experiences, e.g., collecting the data by operating these systems under actual loads, development and technology demonstration projects for introduction of new energy systems, and advisory projects for supporting introduction of new energy systems. For the theme (2), those results reported include the results and examples of the FT projects for power generation by photovoltaic cells and wind power generation, results of the FT project for power generation by fuel cells and creation of the FT projects for pioneer high-efficiency energy systems, current status of the environment-friendly energy community projects (heat supply systems), results and examples of the environment- friendly energy community projects (power generation projects), demonstration tests for establishing the distributed power supply systems of the next generation, tests for establishing techniques for, e.g., load-leveling in power generation by photovoltaic cells for residential purposes, results of the project for technology of utilizing unutilized energy, survey on the techniques for power generation by wastes, and advisory projects for supporting introduction of new energy. (NEDO)

  1. Survey of a technology to introduce the waste-fueled power generation. Basic manual for introduction of the waste-fueled power generation; Haikibutsu hatsuden donyu gijutsu chosa. Haikibutsu hatsuden donyu kihon manual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Local government offices, etc., which are expected to shoulder responsibility for introducing the waste-fueled power generation, want to need exact information on technical information concerning the waste-fueled power generation and the method to materialize the introduction plan, etc. Therefore, Electric Power Development Co. surveyed and studied it under the contract with NEDO. The results were collected together as a basic manual for introduction of the waste-fueled power generation. As an outline of the waste-fueled power generation, the manual explains the significance, the present situation and potentials, the waste-fueled power system, an outline of working out the waste-fueled power generation plan, an outline of construction and operation/maintenance of the waste-fueled power generation, an outline of various systems relating to the waste-fueled power generation, etc. As the items for the study of making a concrete plan for power generation equipment, the manual explains the amount of refuse to be incinerated, the present status of generation capacity as viewed from the quality of refuse, the quality of refuse and the design of power generation equipment, boiler efficiency, power generation efficiency, construction cost and operation cost, etc. In addition, the paper describes a case study of the waste-fueled power generation plan. 118 figs., 39 tabs.

  2. Report for fiscal 1998 on feasibility study for introduction of electric automobiles; 1998 nendo denki jidosha donyu kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys have been made on the characteristics of environmentally harmonizing automobiles, and the status of development and introduction thereof inside and outside the country. Discussions were given on the possibility of introducing electric automobiles in Japan. In developing environmentally harmonizing automobiles in Japan, works have been executed on low pollution type components such as lean burn engines, electric automobiles, gasoline engine and electric motor hybrid cars, methanol fueled cars, and fuel cell automobiles. Some of them are already in use in spite of their high price. In America, a cooperation project for the next generation cars has been implemented by mobilizing industrial, academic and governmental organizations. Based on the achievements thereof, the car makers have announced their original advanced cars respectively. In the EU, development of low exhaust gas cars and zero emission cars is being carried out jointly by the related industries setting years 2003 to 2005 as the target. An urban type traffic system utilizing electric vehicles, and a traffic system dividing movements of short distance and long distance are proposed as the means to introduce the future electric automobiles. (NEDO)

  3. Basic research report on introduction of new energy into Yamaguchi Prefecture; Yamaguchiken shin energy donyu kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In Estimation Work 1, the potentially available amount (the amount in existence) is determined for each type of new energy by use of various new energy related technologies now available. In Estimation Work 2, the available amount is determined for each type of new energy, with social restraint and installation space taken into consideration. Effects upon energy saving and CO2 emission reduction are 4405.2% and 3439.1% in Estimation Work 1, and 6.5% and 8.0% in Estimation Work 2. A conclusion is reached after examining the outcomes of the said estimation works and the results of simulations (conducted on the assumption of new energy introduction in fiscal 2010), the number of advocates expressing their support of new energy adoption in questionnaires answered by various businesses and offices in the prefecture, high possibilities of introduction detected in a survey of exploitation projects of cities, towns, associations, and unions, and the prospect of acceptance by households. The conclusion is that the types of new energy and technologies to be selectively introduced into the prefecture will be photovoltaic power generation, wind power generation, clean energy vehicles, energy extracted from wastes, cogeneration, fuel cells, passive solar system, utilization of waste heat from factories and mills, and ocean energy. These are abundant in terms of potentially available amount and of available amount. (NEDO)

  4. Report for fiscal 2000 investigations on effects imposed by introducing emission trading system; 2000 nendo haishutsuryo torihiki system donyu ni yoru eikyo ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With regard to effectiveness of the emission trading targeted to reduce the greenhouse effect gas emission, evaluation has been given from the three viewpoints: economies, environment, and household economy. In the research, simulations were implemented by using the GEC calculation model modified for introduction of domestic emission trading, and utilization of international emission trading. In evaluating the effects on industries and foreign trades, notice was given on the large energy consuming industries to discuss the effects of introducing the emission trading on the quantity of production and export. Regarding the effects on environment, calculations and discussions were given on greenhouse effect gas leakage rates to assess the greenhouse effect gas emission reducing effects from the domestic and international viewpoints. As a result of the discussions, it was found that the economies, environment and household economy are all benefited in regard with the domestic emission trading. Utilization of the international emission trading was also found to have sufficient positive benefit exist for the economies and household economy. (NEDO)

  5. FY1995 transduction method and CAD database systems for integrated design; 1995 nendo transduction ho to CAD database togo sekkei shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Transduction method developed by the research coordinator and Prof. Muroga is one of the most popular methods to design large-scale integrated circuits, and thus used by major design tool companies in USA and Japan. The major objectives of the research is to improve capability and utilize its reusable property by combining with CAD databases. Major results of the project is as follows, (1) Improvement of Transduction method : Efficiency, capability and the maximum circuit size are improved. Error compensation method is also improved. (2) Applications to new logic elements : Transduction method is modified to cope with wired logic and FPGAs. (3) CAD databases : One of the major advantages of Transduction methods is 'reusability' of already designed circuits. It is suitable to combine with CAD databases. We design CAD databases suitable for cooperative design using Transduction method. (4) Program development : Programs for Windows95 and developed for distribution. (NEDO)

  6. FY1995 transduction method and CAD database systems for integrated design; 1995 nendo transduction ho to CAD database togo sekkei shien system

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Transduction method developed by the research coordinator and Prof. Muroga is one of the most popular methods to design large-scale integrated circuits, and thus used by major design tool companies in USA and Japan. The major objectives of the research is to improve capability and utilize its reusable property by combining with CAD databases. Major results of the project is as follows, (1) Improvement of Transduction method : Efficiency, capability and the maximum circuit size are improved. Error compensation method is also improved. (2) Applications to new logic elements : Transduction method is modified to cope with wired logic and FPGAs. (3) CAD databases : One of the major advantages of Transduction methods is 'reusability' of already designed circuits. It is suitable to combine with CAD databases. We design CAD databases suitable for cooperative design using Transduction method. (4) Program development : Programs for Windows95 and developed for distribution. (NEDO)

  7. On-line temperature control of fluidized bed incinerator using fuzzy algorithm; Fuzzu seigyo donyu ni yoru ryudosogata shokyakuro unten no jidoka

    Energy Technology Data Exchange (ETDEWEB)

    Okayasu, S.; Kuratani, T.; Imai, H. [Ajinomoto Co. Inc., Tokyo (Japan)

    1995-03-15

    Automatic control of incinerators for their stable operation has been desired for the preservation of the environment in the factory. An on-line fuzzy control system has been successfully introduced for temperature control of the fluidized bed of incinerator for industrial wastes. In this case, manual control can be applied to the plant instead of a PID control system, because of the complexity of the waste materials and the large delay in detection of the temperature change in the fluidized bed sand. On the basis of analyzing the dynamic performance of the process and the know-how of skilled operators, membership functions and fuzzy control rules are selected, then determined carefully for the system. Introduction of the system resulted in almost the same performance as manual control. Subsequently the operators are freed from manual operation in the control room for an hour. 6 refs., 5 figs., 4 tabs.

  8. Technical surveys on MHD combustors. Surveys on incorporation of pressurized coal partial combustion furnaces; MHD combustor gijutsu chosa. Kaatsugata sekitan bubun nenshoro no donyu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    The pressurized coal partial combustion (PCPC) furnace is surveyed/studied for its incorporation in MHD generation. The technical development of the atmospheric CPC has been basically completed, and the concept is demonstrated using a test system of commercial size. Many techniques developed for the atmospheric CPC are applicable to the PCPC system. These include structures of the CPC furnace walls, and slag handling and simulation techniques. Combination of PFBC with PCPC or IGCC can bring about many merits, e.g., enhanced efficiency and abated NOx emissions for the combined cycle power generation. These topping cycles, therefore, should be developed in the early stage. MHD power generation is one of the concepts that can enhance efficiency. In particular, the techniques for closed cycle MHD generation have notably advanced recently. The PCPC techniques are useful for coal combustors for MHD generation. Full-scale development works for the direct coal combustion gas turbine systems have been just started for the IGCC systems of the next generation, and the PCPC-related techniques are expected to serve as the central techniques for these turbine systems. (NEDO)

  9. Fiscal 1999 research report. Revision of introduction guidebook for wind power generation; 1999 nendo furyoku hatsuden donyu guide book no kaitei gyomu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Expectations are rapidly growing higher in Japan, whose energy supply structure is but fragile, that new energies upon introduction and diffusion will help settle emerging environmental problems such as global warming. For the acceleration of new energy introduction, it is necessary to supply autonomous entities etc. planning to adopt new energies with various materials such as basic knowledge of new energies, cases of successful introduction, and procedures to follow for their adoption. Wind power generation has come to attract attention as a environmentally-friendly clean method of energy supply, and there is a strong tendency towards its adoption. Under such circumstances, a guidebook has been prepared, in which study results are systematically written as to the items to consider before local autonomies etc. install their wind power generation systems. The main items in the guidebook are the outlines of wind power generation, wind characteristics, wind power generation system, precedents of wind power generation, how to conduct studies about wind power generation, construction and maintenance of wind power generation systems, procedures, laws, and regulations relating to wind power generation, and government subsidies for wind power development. (NEDO)

  10. Report for fiscal 2001 investigations on energy saving assistance institutions in different countries; 2001 nendo kakkoku no sho energy shien seido ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Taking up China, India, Indonesia and Thailand as the object, investigations were performed on political financing measures that can be used for installing energy saving facilities, and on applicable preferential taxation systems that are applied in each country. Indonesia has no aid measures such as subsidies and political financing directly purposed for energy conservation. Import duty exemption is applied for the purpose of promoting investments. Three kinds of funds are available through IFCT to implement fund aid to protect the environment. Energy saving fund has been established as an energy saving policy to provide subsidies. Energy saving machineries recognized by the investment committee are exempted from the import duties. India has no political financing measures directly purposed for energy conservation. Its preferential taxation system for energy conservation includes the 100% accelerated amortization system for energy saving machineries and facilities, and the preferential import duty system. In China, the financing from the China National Development Bank is considered utilizable in installing energy saving facilities. The country has no aid measures in the taxation system, but fund aid and subsidy by supplementing interest are provided. (NEDO)

  11. Surveys in Hokkaido on promotion of structuring models to be introduced to convert wastes into energy; Hokkaido ni okeru haikibutsu energy ka donyu model kochiku sokushin chosa

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    With an objective of converting dairy farming wastes and fisheries wastes into resources to be used as energies, this paper discusses development trends and utilization possibilities thereof based on their utilization characteristics. The Tokachi, Abashiri and Nemuro regions produce more cattle wastes, and regions on the coast of the Sea of Okhotsk produce more hepatopancreas of scallop than other regions. The amount of energy from such wastes is subject to large seasonal variations. Methane gas production through methane fermentation is an effective treatment technology, although it is utilized less effectively in Hokkaido. Important is applying the processes depending on energy demand, supply characteristics and regional features. Taking waste utilization characteristics and regionally uneven distribution of resources into account, conceptions on six model systems that could be introduced were structured. The six systems include two types for fisheries wastes utilization, three types for agricultural and dairy farming wastes, and one type for combined utilization of agricultural and fishery wastes. Important factors to select suitable commercial operation sites and promote the operations are stable quantity assurance of waste resources, energy demand, and stable operation, such as could be available in fishery processing complexes and large dairy farming areas. 44 refs., 66 figs., 29 tabs.

  12. Fiscal 1998 research report. Feasibility survey on offshore wind power generation in Japan; 1998 nendo chosa hokokusho. Nippon ni okeru yojo furyoku hatsuden no donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey studied the feasibility of large-scale offshore wind power generation in Japan. Attempt was also made on preparation of outline maps of offshore wind around Japan. The cost of future offshore wind power generation systems is roughly dependent on technical issues and environmental issues. As technical issues, 'installation site,' 'foundation,' 'system interconnection' and 'maintenance/management' were summarized based on applications in Europe. As a result, it was clarified that technical issues can be solved with existing technologies to a certain extent, however, those relate to economical problems closely. The previous environment impact assessments say that wind power generation has no problems on the environmental issues. As relatively strong wind coastal areas, the outline maps of offshore wind point out Western Hokkaido area, Japan Sea area of Tohoku district, Pacific ocean area of the central part of Honshu, Genkai Nada area, Western Kyushu area and Southwest islands area, and suggest that these areas are promising for offshore wind power generation. (NEDO)

  13. Fiscal 1998 research report. Feasibility survey on offshore wind power generation in Japan; 1998 nendo chosa hokokusho. Nippon ni okeru yojo furyoku hatsuden no donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey studied the feasibility of large-scale offshore wind power generation in Japan. Attempt was also made on preparation of outline maps of offshore wind around Japan. The cost of future offshore wind power generation systems is roughly dependent on technical issues and environmental issues. As technical issues, 'installation site,' 'foundation,' 'system interconnection' and 'maintenance/management' were summarized based on applications in Europe. As a result, it was clarified that technical issues can be solved with existing technologies to a certain extent, however, those relate to economical problems closely. The previous environment impact assessments say that wind power generation has no problems on the environmental issues. As relatively strong wind coastal areas, the outline maps of offshore wind point out Western Hokkaido area, Japan Sea area of Tohoku district, Pacific ocean area of the central part of Honshu, Genkai Nada area, Western Kyushu area and Southwest islands area, and suggest that these areas are promising for offshore wind power generation. (NEDO)

  14. Fiscal 1999 survey report on introducing technique for predicting impact on hot spring; 1999 nendo onsen eikyo yosoku shuho donyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-10-01

    For the application of fruits of the geothermal development promotion project to survey phase C and for the study of technical means for appropriate development to employ after phase C, some cases of impacts imposed on hot springs by geothermal development were taken up and the causes of the impacts were investigated. Activities were conducted in the three fields of (1) the survey of actualities of impacts imposed on hot springs, (2) the survey of the causes of such impacts, and (3) a comprehensive survey. Keyword searches were conducted into the data system and geothermal energy related magazines, and 13 cases were found in which hot springs were affected by geothermal development, which included the Palinpinon district (Philippines), the Koso district (America), and the Wairakei district (New Zealand). Concerning the 13 cases, data on geology, geological structures, and geothermal fluids were collected and studies were conducted about relations of geothermal development with geological structures and geothermal fluids, as in the case of hot springs, and the two were integrated for the clarification of the causes of impacts. In concluding the report, the difference in mechanism is deliberated between cases with impacts on hot springs and cases without impacts on hot springs. (NEDO)

  15. Investigation on the development and introduction of new geothermal exploration technology. Part 2; Chinetsu shintansa gijutsu kaihatsu donyu ni kansuru chosa. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    For the purpose of maintaining and increasing the geothermal power generation amount, the development was made of exploration technologies which become necessary in the stage of geothermal reservoir exploration and in the stage of reservoir management and peripheral development. As development technologies, the following were proposed: fracture flow characteristics exploration method (FE), production/circumference areas flow characteristics exploration method (PE), and integrated analyzing method (IA). As to FE, for the survey of geothermal fluid dynamic characteristics in fracture aggregate composing the geothermal reservoir, developments were made of the well hydraulic testing method for examining hydraulic characteristics of fracture system and of the fracture evaluation method composed of the core/logging analysis method, the permeability logging method and electroseismic exploration method. As to PE, for maintaining and managing steam production in the developmental area and developing the area to the circumference area, development was conducted of technology for exploring variations of reservoirs and fluid flow from the data on precision gravity, three-dimensional resistivity, fluid geochemistry, active seismic wave and self potential, precision electromagnetism, passive seismic wave, etc. As to IA, development was made of reservoir simulation technique, etc. 2 refs., 70 figs., 41 tabs.

  16. Report on survey in fiscal 2000 on the feasibility study on structuring research aiding net; 2000 nendo kenkyu shien net no kochiku ni kansuru kanosei chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A study has been performed on the possibility of efficient utilization of research resources by summarizing the resource information for research and development by the industrial, governmental and academic areas and by providing research organizations with the information through the Internet. As a result of the survey on research aiding cases that apply the network used by the public organizations and corporations inside and outside the country, it was found that Japan often utilizes research facilities and holds seminars having selected regional research organizations, while the U.S. provides large-size aids in wide area, such as technological information service, patent service, and human resource service. A questionnaire survey was conducted on interests toward the necessity of research aids, specific needs for aids, and provided services. As a result, it was revealed that interest toward the research aiding net is considerably high, and strong demands are present in structuring database for the research human resource information, needs information, and information on researchers in different fields. Discussions were given on structuring the research aiding net, wherein the system contents, structuring expense, and the development schedule were presented. (NEDO)

  17. CAE to support a part of supporting technologies-its applications and verifying samples. Shien gijutsu no ittan wo sasaeru CAE sono torikumi to kensho rei

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, H. (Polyplastic Co. Ltd., Tokyo (Japan))

    1992-01-01

    Plastic CAE has suddenly being widened their applicable fields recently. On the other hand, since integated program development has also been made worldwidely, currently it is posssible to execute even for shrinkings and warping and warping analysis based on holding pressure analysis and cooling analysis. Polyplastics Company Inc. has paid attention to the usefullness of CAE technologies for engineering plastics from the early times, and in order to utilized them effectively, they have progressed several examinations on CAE software development, improvement of CAE analysis technologies, confirmation and verification of CAE analysis precision, resin data preparations and measuring methods, etc. In this paper, their applications have been introduced mainly by their verification samples such as output sample of FACE-2, which is their originally developped metal mold temperature adjustment design supporting system, and as for verification samples of warping deformation analysis, experimental result of testing metal mold (box type), and reliabilities on the results of measured precision and quantitative analysis of resin data to be used for analysis. 6 refs., 6 figs., 1 tab.

  18. FY 1998 annual report on the survey on development, introduction and promotion of urban type multipurpose geothermal utilization techniques; 1998 nendo toshigata tamokuteki chinetsu riyo gijutsu no kaihatsu, donyu, sokushin ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Introduction of geothermal heat pump systems, which depend on temperature differential, is investigated for urban areas, which have large energy demands. Results of the surveys on the current situations of geothermal heat pump (GHP) systems indicate that they have already numbered 300,000 units in USA and totaled more than 50,000 units in Switzerland and Northern European countries, and that they are increasing at an annual rate of higher than 10%. The results also indicate that introduction of these systems are well feasible in Japan, which generally has better topographical conditions than American and European countries, and the GHP system with vertical ground heat exchanger is investigated for its topographical and environmental considerations. These systems could annually abate approximately 52 million tons of CO2 (4.3% decrease), if disseminated to all households. They are also expected to help control the heat island phenomenon, and reduce peak power consumption. The technological problems to be solved before these systems are massively disseminated including development of small scale drilling rigs and preparation of drilling manuals. System standardization and introduction of subsidy systems are also needed to massively disseminate these systems. (NEDO)

  19. FY 1994 report on the survey and research of introduction, promotion of proliferation and guidance on new energy introduction. Pt. 2; 1994 nendo shin energy donyu fukyu sokushin shido ni kansuru chosa kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Survey, collection and analysis were performed on different items of information required for new energy technologies. Studies were carried out to structure a system to support smooth execution of technical guidance and consultation. Among the project areas for field tests on photovoltaic power generation systems for public facilities, measurements were executed on hourly power demand in facilities in snowy and cold districts with little data available. In putting different items of information into a database, data were collected and put into order for the following items: statistics on average value for ten years of insolation time in 842 locations nationwide, calculation of insolation on slanted surface at the insolation measuring points (slanting angles and insolation on the slanted surface at which energy amount available for power generation is maximized in a year, as obtained by estimating the insolation on horizontal surface from the insolation duration), and expansion and addition of the introduction examples. Specifications for solar cell modules and inverters were classified and put into order, and so were on types, specifications, and product descriptions for photovoltaic power generation systems for individuals' houses. The aid system structured in the previous year was discussed for improvement, and new information was put into a database to improve the aid system. (NEDO)

  20. FY 1994 report on the survey and research of introduction, promotion of proliferation and guidance on new energy introduction. Pt. 2; 1994 nendo shin energy donyu fukyu sokushin shido ni kansuru chosa kenkyu. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Survey, collection and analysis were performed on different items of information required for new energy technologies. Studies were carried out to structure a system to support smooth execution of technical guidance and consultation. Among the project areas for field tests on photovoltaic power generation systems for public facilities, measurements were executed on hourly power demand in facilities in snowy and cold districts with little data available. In putting different items of information into a database, data were collected and put into order for the following items: statistics on average value for ten years of insolation time in 842 locations nationwide, calculation of insolation on slanted surface at the insolation measuring points (slanting angles and insolation on the slanted surface at which energy amount available for power generation is maximized in a year, as obtained by estimating the insolation on horizontal surface from the insolation duration), and expansion and addition of the introduction examples. Specifications for solar cell modules and inverters were classified and put into order, and so were on types, specifications, and product descriptions for photovoltaic power generation systems for individuals' houses. The aid system structured in the previous year was discussed for improvement, and new information was put into a database to improve the aid system. (NEDO)

  1. FY 1994 Report on the results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers; 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu saiteki donyu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Described herein are the FY 1994 results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers or the like. The necessary economic conditions for introduction of a fuel cell system to be competitive with the conventional system which individually supplies electric power and heat are 250,000 yen/kW as the construction unit cost, 0.10m{sup 2}/kW as the installation area, 5 years as the cell body life, use of an inexpensive fuel gas (2 to 6 yen/Mcal). Moreover, it is an indoor system which shall have the operational characteristics to follow daily demand fluctuations while operating under the optimum conditions in the urban redevelopment area considered. A 5,000kW-class fuel cell plant burning fuel gas (2 yen/Mcal) will need a total floor area of approximately 400,000 m{sup 2} in an energy-intensive office type demand area. These conditions shall be met in order to economically introduce the 5,000kW-class plant. It is also necessary to compare the plant with the competitive cogeneration plants. The specifications for the prototype now under consideration are sufficient for the energy-saving effect, and it is premised that these specifications and characteristics are secured. (NEDO)

  2. Robot and mechatronics equipment for daily life support in high-elderly and small number of child society; Chokorei/shosika shakai seikatsu ni shien shitekureru robot/mekatoro kiki

    Energy Technology Data Exchange (ETDEWEB)

    Fujie, M. [Hitachi Ltd., Tokyo (Japan)

    1997-07-05

    As for high-elderly society, Japan is going to face in near future, self dependency without depending on others as far as possible of bed ridden people or people using wheel chair and also including the probable elderly ones is going to be necessary. In Japan, there is so far accumulation of high level mechatronics technology and it is thought that there is possible to develop a system to fulfill such needs. In this system, equipment has deep connection with human being and natural coexistence between the equipment and human being is most necessary. Accordingly, development and practical use of walking practicing machine used for elderly people, walking support system, daily life work support system and so forth are expected by making successful in practice the coexistence functions of high level robot/mechatronics technology and machine/man. However, the study regarding the technology that are common to man and machine, particularly, research of mental characteristics and physical characteristics of human being is still insufficient and further results are expected. 9 refs., 12 figs.

  3. FY 1998 annual report on the introduction/dissemination working group. 19th R and D activity report; 1998 nendo donyu fukyu jigyo bunkakai. Dai 19 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    Summarized herein are the FY 1998 R and D activities by the introduction/dissemination working group, extracted from the 19th R and D activity report by NEDO. Mr. Yamaho, a NEDO's director, reports (General situations of the new energy introduction promotion department). The R and D project results include those of renewable energy sources, such as the results of the field test and supporting projects for solar light power generation, wind power generation and solar heat utilization; and those of recycling type energy, such as the results of the field test projects for power generation by wastes and fuel cells, and the results of the projects for district heat supply by co-generation systems. The other results presented include those of the projects for dissemination of clean energy vehicles, supporting new energy entrepreneurs, promotion of introducing district new energy, drawing visions for district new energy, field tests for introducing high-performance industrial furnaces, modeling for introducing facilities for rationalized use of pioneer energy, promotion of disseminating ice-aided, heat-storage type air conditioning systems, and promotion of introducing decentralized gas-aided air conditioning for existing small- to medium-sized buildings. (NEDO)

  4. Introduction of anti-rolling active vertical fin and its application to maneuverability for displacement-type super high speed ship. 2nd Report.; Haisuiryogata chokosokusen no yokoyure seishiyo active suichoku fin no donyu to sojuseieno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Hirayama, T; Saito, Y [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Niihara, Y [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1997-12-31

    Discussed herein are the effects of vertical fin projecting downwards from the bottom of a displacement-type superhigh-speed ship, installed to improve its transverse stability and turning ability. The system for simultaneously controlling rudder and vertical fin by the optimum regulator was studied for maneuverability in directional following waves and smooth water, and maneuverability was simulated numerically. A ship is greatly rolled and sloped when running in waves. It is found that the vertical fin shows a high anti-rolling effect when the ship runs straight. The optimum regulator greatly improves maneuverability in waves, reducing rolling by 92%. Increased rolling with the vertical fin, observed in the previous study in directional following waves, is found to be due to the rudder. The optimum position of the fin is determined to control transverse sloping of a turning ship in a superhigh-speed region. 21 refs., 12 figs., 4 tabs.

  5. Introduction of anti-rolling active vertical fin and its application to maneuverability for displacement-type super high speed ship. 2nd Report.; Haisuiryogata chokosokusen no yokoyure seishiyo active suichoku fin no donyu to sojuseieno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Hirayama, T.; Saito, Y. [Yokohama National University, Yokohama (Japan). Faculty of Engineering; Niihara, Y. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1996-12-31

    Discussed herein are the effects of vertical fin projecting downwards from the bottom of a displacement-type superhigh-speed ship, installed to improve its transverse stability and turning ability. The system for simultaneously controlling rudder and vertical fin by the optimum regulator was studied for maneuverability in directional following waves and smooth water, and maneuverability was simulated numerically. A ship is greatly rolled and sloped when running in waves. It is found that the vertical fin shows a high anti-rolling effect when the ship runs straight. The optimum regulator greatly improves maneuverability in waves, reducing rolling by 92%. Increased rolling with the vertical fin, observed in the previous study in directional following waves, is found to be due to the rudder. The optimum position of the fin is determined to control transverse sloping of a turning ship in a superhigh-speed region. 21 refs., 12 figs., 4 tabs.

  6. Report for fiscal 2000 on surveys on foundation to establish industrial technology strategy. Surveys on foundation to assist activation of research and development; 2000 nendo sangyo gijutsu senryaku sakutei kiban chosa hokokusho. Kenkyu kaihatsu kasseika shien kiso chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In order to help discuss the measures to activate researches and developments in private corporations, surveys were made on barriers and factors related to industrial technology research and development by fields, and discussions were given on structuring research and development models. Factors impeding research and development processes relate to a case of each phase in the fundamental research, applied research, and product development, and a case of human resources, funds and information. A policy of structuring models was determined to make quantitative the effects of different aiding systems of the government for researches and developments in private corporations. Case analyses were conducted by using a pilot model. In the present research, a questionnaire survey was carried out to acquire such data as R and D time lag, and to identify the effects of the policies. Surveys were also performed on research and development programs in North America, by making interviews to concerned corporations. As a result of the surveys, such problems were extracted as research and development fund, freer flow of human resources, research and development systems, handling of results of researches performed by consortiums, accounting systems, and sale of the government owned patents. (NEDO)

  7. Survey of the measures to be concretely taken for CEV introduction/spread in the region; Chiiki ni okeru CEV donyu fukyu no tame no gutaiteki hosaku ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the Hanshin/Harima region where CEV introduction/spread are expected and there is a great pervasive effect, survey/study were conducted to plan the construction of facilities for natural gas vehicle fuel supply in future. In the survey, the paper summed up the state of CEV spread in the Hyogo prefecture, the state of construction of fuel supply facilities, etc. Further, by the questionnaire survey, the needs for construction of fuel supply facilities were grasped, and the intention of introducing natural gas vehicle was sounded out. In the study of a wide-area construction plan for natural gas fuel supply facilities, the Hanshin/Harima region was divided into zones based on geographical conditions, traffic system, etc., and the number of the needed fuel supply facilities was calculated which corresponds to the targeted number of natural gas vehicle introduction set up by the nation. Moreover, by the questionnaire survey, the needs for fuel supply facilities were grasped, and a method for setting up the order of priority in the construction was determined/proposed. Through the study of these, a manual was made out which is usable for the CEV introduction and the construction plan for natural gas fuel supply facilities in other regions. (NEDO)

  8. NEDO Forum 2001. Session on New Energy/Energy Conservation Popularization Project (Let's walk and save energy - Let new energy run on its course); NEDO Forum 2001. Shinene shoene donyu fukyu jigyo session (aruko shoene hashiro shinene)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Professor Kashiwagi of Tokyo University of Agriculture and Technology in his keynote address, entitled 'How the popularization of new energy and energy conservation should be in the future,' discussed energy conservation measures, new energy measures, fuel conversion, natural gas, and atomic energy, and disclosed his long-term outlook of energy supply and demand. NEDO in its achievement report mentioned a simulation on the smooth interconnection of distributed power sources such as wind power sites to a commercial power system. It reported also that, under its 3-year high performance industrial furnace field test project started in 1998, 167 furnaces, including heating furnaces, ladles, heat treatment furnaces, melting furnaces, and gas treatment furnaces were converted into high performance industrial furnaces capable of high temperature preheated air combustion near 1000 degrees C and that the conversion brought about a great reduction in energy consumption and in carbon dioxide gas and nitrogen gas emissions. (NEDO)

  9. Discriminations of critical conditions of a high speed ship in quarterings sea waves by using tools of the sea state determinations by GMS. Eisei joho kaisho settei shien tool ni motozuku chokosokusen no shatsuiha rinkai jotai no hanmei

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, S.; +Ishida, T. (Kyushu University, Fukuoka (Japan)); Shinkai, A. (Kyushu University, Fukuoka (Japan). Faculty of Engineering)

    1991-09-04

    The documentation assumes a new type high speed ship, higher than 50kt in speed and heavier than 1000ton in dead weight, to require the ocean goingness, middle distance navigation and high speed transport. The present report dealed with how to discriminate a ship, navigating at a high speed on oceanic waves, in critical condition against the encountering waves. Navigating far distantly from the shore, the ship was generally made to positively utilize the information data from the geostationary metheorological satellite (GMS) to be applied as a support soft tool for the maritime system and other designs. As a result, the high speed ship on the quartering waves was numerically elucidated in critical condition against the encountering waves and simultaneously assumed in critical course upon discriminating the critical condition in a concretely designated oceanic area. It was shown that, if different Froude numbers are calculated and ordered of critical circular frequency, angle, wave period, etc. against the encountering, a dimensionally arbitrary ship is easily discriminatable in critical course in an arbitrary oceanic area by utilizing a GMS determination support tool. 12 refs., 14 figs., 2 tabs.

  10. FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

  11. Achievement report for fiscal 1997 (New Sunshine Project) on the development of superconductor power application technology. Research on a total system / investigative research on introduction effects; 1997 nendo chodendo denryoku oyo gijutsu kaihatsu (New Sunshine keikaku) seika hokokusho. Total system nado no kenkyu / donyu koka no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes investigation and discussion on effects of introducing a superconductor power application technology. The generator sub-committee has compared features, technical problems and development expenses in the first and second proposals, but has not reached the final conclusion. The first proposal is targeted for early realization of 200-300 MW class generators with development cost of six to seven billion yen and a development term of seven years. These developments raise largely towards practical application the levels of material technologies, fabrication and processing technologies, and analysis and design technologies. The second proposal is intended of developing 200-300 MW class generators targeted for increased diameter, as a reduced size machine of a 600-MW generator being a future generator. It will take development cost of eight to nine billion yen with the period of nine years for the development. Majority of the technologies required for developing the future 600-MW class generator can be demonstrated. The AC superconductor device sub-committee has investigated design examples, clarified the specification requirements, and investigated and studied the development measures. The oxide superconductor sub-committee has investigated and studied making wires and conductors, and device application feasibility, but has not reached the stage of presenting specific research and development methods. The practical application strategy sub-committee has also not been able to present a collective measure because of difficulty of making future prospect on the electric power business. (NEDO)

  12. FY 1996 report on the results of the development of superconductor power application technology. Study of a total system, etc. (Investigational study of the introductory effect); 1996 nendo chodendo denryoku oyo gijutsu kaihatsu seika hokokusho. Total system nado no kenkyu (donyu koka no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Under the secondary interim assessment made in FY 1995 between the assessment committee of the energy/environment technology development sectional meeting of the Industrial Technology Deliberation Council and NEDO, in this project, the following were conducted in FY 1996: study of trial manufacture of superconductor motor model machine and R and D of element technology (conductor technology/refrigerator technology). The study was proceeded mainly with Super-GM, and as to the motor, the preparation for test on a part of the model machines was finished. Considering FY 1998 which is the final year of this project, the investigational study in FY 1996 aims at accumulating/arranging/analyzing the data which help judge how to proceed with the future R and D of superconductor power application technology continuously based on the secondary interim assessment. For superconductor motor and various superconductor power appliance, economical/technical feasibilities and methods of R and D and surveys of trends in Japan and abroad for the R and D were made important items. Further, 'R and D of the basement of superconductor power application' proposed in the secondary interim assessment (R and D of the combination of elements which become the basement of equipment technology over a stage of parallel R and D of element technology of conductor, etc.) targeted the presentation of concrete details. (NEDO)

  13. Report on achievements in fiscal 1999. Research and development of carbon-based high-function material technologies (research and development of ocean bottom petroleum production system); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    As part of the research and development of carbon-based high-function material technologies, research and development has been performed on a material creating technology and a process technology to crease mechanically high-function materials. The former technology performs synthesis by using the electron excited CVD process and the explosion synthesizing process, intended to analyze the structure and properties thereof. It is intended to synthesize nitriding-based carbon films and elucidate their composition and structure by using the mass separation ion beam method and the laser beams. Synthesizing nano tubes by utilizing catalytic reactions, and investigating their properties are intended by using the thermal CVD process, plasma CVD process and arc discharge process. Elucidation is intended on the reaction and production mechanisms of carbon-based materials, theory estimation, structures possessed by the carbon-based materials, and mechanisms to manifest their characteristics. The latter technology relates to the three assignments subjected to a composition inclining film forming technology, a complex shaped film forming and micro processing technology, and a large area film forming technology. It is intended to utilize positively such properties as low friction and wear performance and high-temperature corrosion resistance expected in high-function carbon-based materials including amorphous carbon, diamond and nitrided carbon for the purpose of application to surface protection of movable parts in different industrial machines, and building materials including glasses. (NEDO)

  14. FY 1999 report on the results of the technology development of super metal (R and D of the undersea oil production support system). Development of technology of aluminum-base high corrosion resistant fine structure controlling metal materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu (aluminium kei kotaishokusei bisai kozo seigyo kinzoku zairyo gijutsu kaihtsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing aluminum materials excellent in industrial characteristics, a study was conducted to create large-sized aluminum materials having mesoscopic crystal structure, and the FY 1999 results were summarized. In this fiscal year, to create the fine crystal grain structure, the following were conducted: fundamental study of high strain accumulation process, study of a mechanism of fine crystal grain formation, development of the processing method, and development of evaluation technology. In the study of high strain accumulation process, effects were examined of conditions of molten metal rolling on castability. Fundamental studies were also made of innovative technologies such as ECAP method, pre-forged structure controlling rolling, accumulative roll bonding and thermomechanical treatment. In the study of the mechanism of fine crystal grain structure formation, the following were conducted: Al-Mn base alloys produced by molten metal rolling, 6061 alloys by warm rolling with different peripheral speed rolling, and 7000 group alloys by warm rolling. As to the processing method, study was made on low-temperature rolling technology and rapid heat treatment technology. As to the evaluation technology, study was made on evaluation of crystal grain diameter by EBSP. (NEDO)

  15. FY 1998 report on the results of the R and D of industrial science technology. R and D of 'carbon-base high functional material technology' (R and D of the submarine oil production support system); 1998 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Tansokei kokino zairyo gijutsu no kenkyu kaihatsu (kaitei sekiyu seisan shien system kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    For the R and D of carbon-base high functional materials, the paper reported on (1) material creation technology and (2) creation of mechanically high functional materials. In (1), the synthesis of new BCN-base materials is conducted by the electronic excitation CVD method and high temperature/high pressure (explosive synthesis) with the aim of analyzing the composition/structure. Using energy-controlled ion beams and laser beams, the synthesis of new CN-base materials and analysis of composition/structure are aimed at. By the thermal CVD method using catalysts, a method to synthesize a quantity of nanotubes is aimed at. The paper is aimed at clarifying the reaction mechanism on the material conversion of carbonaceous materials relating to the above-mentioned three methods and the appearance mechanism of characteristics of carbonaceous materials. (2) is composed of the following three subjects: composition gradient film formation technology, complicated shape film formation/micro-processing technology, and large area film formation. These three subjects were studied to positively make use of characteristics such as low friction/low abrasion and high temperature corrosion resistance which can be expected in amorphous carbon, diamond and high functional carbon materials of carbon nitride and to apply them to moving parts of various industrial machines and surface protection of construction materials such as glass, etc. (NEDO)

  16. FY 2000 report on the results of the R and D of 'frontier carbon technology.' R and D of a system to support production of undersea oil; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This report summarized the results of the FY 2000 R and D of frontier carbon technology (FCT). In Chapter 1, technology of original production of substances, new carbon-base substances such as hetero-diamond and carbon nitride with high-grade and various characteristics are synthesized. And, the following are also established: method to synthesize nanotubes, etc. in quantity, technology to control interatomic bonding, technology to control hetero-element replacement, etc. BCN films were obtained by film formation by changing the gas component ratio of diborane, methane and nitrogen by the electron beam excitation CVD method. The sp{sup 3} bonding control in carbon film was advanced. By reacting benzene with raw materials using nickel phthalocyanine as catalyst, carbon nanotube with a 60nm diameter was obtained. Using ECRCVD device, carbon fiber was synthesized on Si substrate. In Chapter 2, original production process technology of mechanical high function materials, subjects are as follows: composition gradient film forming technology, complicated morphology film formation/micro processing technology, technology to apply carbon-base materials to tribology. The application of the materials to the movable part of various industrial machines is considered by making use of characteristics such as low friction and low abrasion which are expected of amorphous carbon, diamond, carbon nitride, etc. (NEDO)

  17. FY 2000 report on the results of the R and D of 'frontier carbon technology.' R and D of a system to support production of undersea oil; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Kaitei sekiyu seisan shien system kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This report summarized the results of the FY 2000 R and D of frontier carbon technology (FCT). In Chapter 1, technology of original production of substances, new carbon-base substances such as hetero-diamond and carbon nitride with high-grade and various characteristics are synthesized. And, the following are also established: method to synthesize nanotubes, etc. in quantity, technology to control interatomic bonding, technology to control hetero-element replacement, etc. BCN films were obtained by film formation by changing the gas component ratio of diborane, methane and nitrogen by the electron beam excitation CVD method. The sp{sup 3} bonding control in carbon film was advanced. By reacting benzene with raw materials using nickel phthalocyanine as catalyst, carbon nanotube with a 60nm diameter was obtained. Using ECRCVD device, carbon fiber was synthesized on Si substrate. In Chapter 2, original production process technology of mechanical high function materials, subjects are as follows: composition gradient film forming technology, complicated morphology film formation/micro processing technology, technology to apply carbon-base materials to tribology. The application of the materials to the movable part of various industrial machines is considered by making use of characteristics such as low friction and low abrasion which are expected of amorphous carbon, diamond, carbon nitride, etc. (NEDO)

  18. Fiscal 1996 report on the comprehensive invetigational research on medical instruments. Development of a trace collection/microanalysis system of blood, etc.; development of a high accuracy three dimensional image diagnosis system; development of a low invasion operation supporting system; development of artificial internal organ technology; 1996 nendo chosa hokokusho sogo chosa kenkyu (iryo kiki). Ketsuekinado biryo saishu/biryo bunseki system kaihatsu, koseido sanjigen gazo shindan system kaihatsu, teishinshu shujutsu shien system kaihatsu, jinko zoki gijutsu sogo kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    In accordance with the rapidly advancing phenomena of decreasing in number of child and aging in Japan, enhancement in quality of medical care and welfare is an issue to be urgently considered, and importance of the support by technology of medical instruments is increasing. The purpose of this research is to extract subjects of the element technology, which will be important strategically and in the long run, from two viewpoints of the needs side and seeds side to study the course of the development of medical instruments. For this, questionnaires were sent out to learned persons in charge of work connected with medical care to grasp the needs for the future development of medical instruments. Based on them, the paper extracted subjects of the element technology which are considered to become strategically important in Japan. The report outlined the investigational research and arranged the methods and results of the survey of the needs for the development of medical instruments. Next, the paper described the method to extract important subjects of the element technology from the needs survey, and then arranged important subjects of the element technology extracted through the study in the committee. At last, the paper generalized the investigational research and summarized the remaining subjects, etc. at the same time. 11 tabs.

  19. FY 1989 report on the results of the development of the entrained bed coal gasification power plant. Support study for the development of the entrained bed coal gasification power plant; 1989 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu (Funryusho sekitan gaska hatsuden plant kaihatsu no shien kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-05-01

    For the purpose of supplying the data necessary for construction/operation/maintenance of system, gas turbine, etc. of the desulfurization/dust removal process to be adopted to a pilot plant of 200t/d entrained bed coal gasification power generation, support study was made using the Yubari 40t/d test equipment, and the FY 1989 results were summarized. As to the operation of the 40t/d gasification system, operation was stably continued, and also the system was able to feed gas to the wake device. In the high temperature dry desulfurization test, test was made on the following: structure of the sampling system of the continuous analyzer installed in the coal gas system and circulation gas system, load response corresponding control system, sequence control of the system for supplying reducing agent to SO{sub 2} reduction tower and the system for ash discharge, back washing of D-42 lift gas filter, etc. In the high temperature dry dust removal test, improvement in filtration material/dust separation performance, sequence control of the filtration material supply/discharge system, continuous dust densitometer, operational automation, etc. Through the tests, obtained were the results that are useful for the 200t/d plant. (NEDO)

  20. Survey report for fiscal 1998. Surveys on possibility of introducing element technologies and future technological trends in the ECO and ENERGY city projects; 1998 nendo chosa hokokusho. Ekoene toshi project ni okeru yoso gijutsu donyu kanosei to kongo no gijutsu doko ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Covering ECO and ENERGY projects currently on the way under the New Sunshine Project, discussions were given on the possibility of utilizing the technological achievements, and the technological problems therein, from the energy supply and utilization aspects. Taken up as the basic concept of the ECO and ENERGY projects is 'optimization and implementation of a cascade-type energy system in cities under environmental restrictions'. Targets were placed on optimization of a total system including the demand side (a topping system), optimization of a total system including secondary energy other than heat (electric power and gas for example), optimization of energy efficiency for the system as a whole, and minimization of environmental load. The ECO and ENERGY technologies that are assumed for the future application were classified into the following six fields: the optimal energy supply system development field, heat storing technology field, thermoelectric power generation field, environment friendly heat pump system technology field, waste heat utilizing heat cycle technology field, and LNG cold heat utilizing technology field. (NEDO)

  1. Survey report for fiscal 1998. Surveys on possibility of introducing element technologies and future technological trends in the ECO and ENERGY city projects; 1998 nendo chosa hokokusho. Ekoene toshi project ni okeru yoso gijutsu donyu kanosei to kongo no gijutsu doko ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Covering ECO and ENERGY projects currently on the way under the New Sunshine Project, discussions were given on the possibility of utilizing the technological achievements, and the technological problems therein, from the energy supply and utilization aspects. Taken up as the basic concept of the ECO and ENERGY projects is 'optimization and implementation of a cascade-type energy system in cities under environmental restrictions'. Targets were placed on optimization of a total system including the demand side (a topping system), optimization of a total system including secondary energy other than heat (electric power and gas for example), optimization of energy efficiency for the system as a whole, and minimization of environmental load. The ECO and ENERGY technologies that are assumed for the future application were classified into the following six fields: the optimal energy supply system development field, heat storing technology field, thermoelectric power generation field, environment friendly heat pump system technology field, waste heat utilizing heat cycle technology field, and LNG cold heat utilizing technology field. (NEDO)

  2. FY 1998 report on the development of technology for reservoir mass and heat flow characterization. Theme 5-2. Monitoring and modeling of reservoir mass and heat flows (Integrated reservoir modeling and simulation techniques/Modeling support technique); 1998 nendo chinetsu tansa gijutsu nado kensho chosa choryuso hendo tansaho kaihatsu hokokusho (yoyaku). 5-2. Choryuso hendo yosoku gijutsu (modeling shien gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This R and D are aimed at establishing technology to support the reservoir modeling work required for predicting the reservoir variation from the geological/geochemical side. The contents of the development are (1) establishment of the practical measuring system for core fracture system, and (2) establishment of new modeling support technology. In (1), as the core fraction system measuring system, the measurement of fluid inclusion homogenization temperature and melting point and laser Raman spectroscopy were applied to the Wasabizawa area to obtain the results. In (2), the R and D were conducted of a rapid age measuring method for altered rock/unaltered rock and an analytical method for fluid flow using trace chemical components of hydrothermal minerals. In the former, 3-D thermoluminescent intensity of the age-known quartz was measured. The TL age of weak altered rock of Kijiyama dacite in the Wasabizawa area was 320Ka, almost the same result as 320Ka already reported. In the latter, trace components of quartz were measured at each well, and changes in the depth direction were made clear. It was made clear that the variation of Na/K ratio is large around the lost circulation stratum. The geothermal fluid flow was made clear by the analysis of similarity of the intensity ratio. (NEDO)

  3. Survey report for fiscal 1999 on foundation of strategy formation for industrial technologies. Strategy of foundation and environment buildup (Further into support for technological innovation); 1999 nendo sangyo gijutsu senryaku sakutei kiban chosa hokokusho. Kiban kankyo senryaku gijutsu kakushin shien shisaku shinkutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Surveyed are the roles of the government, important for environmental buildup for technological innovation. The U.S. research and development support programs are classed into contracts, grants, cooperative agreements, and CRADAs (Cooperative Research and Development Agreements). The government financially supports the first three, but not CRADA. It provides CRADA with manpower, facilities, and resources. The research and development (R-and-D) appropriation not for national defense in the U.S. fiscal 2000 budget is up 36% to $39.4 billion occupying 50.6% of the total R-and-D expense. The basic research appropriation is given the highest priority, enjoying an increase of 4.7% to $18.1 billion. In the U.S., taxation for R-and-D expenses is done in two ways. One is a research expense tax deduction system under which R-and-D expense is handled as a cost, a subject of deduction. The other is a research and experiment tax deduction system under which a certain percentage of R-and-D increment is free of taxation. NEDO's (New Energy and Industrial Technology Development Organization) system for national R-and-D projects is scheduled to change extensively upon reorganization of the government ministries and agencies in January, 2001. Under the circumstances, the current and future systems of the state supports for R-and-D are outlined, and the position of NEDO in them is clarified. The R-and-D systems of the entrusted businesses and the problems they contain are also described. (NEDO)

  4. Report on investigations in fiscal 2000 on the basic investigation on promotion of joint implementation. Introduction of central load dispatching center in Oman; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Oman koku ni okeru chuo kyuden shireijo no donyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In Oman, electric power supply is made by operating a large number of gas turbine generators. However, the operation is inefficient as a whole as a result of operating the generators provided with large reserves to minimize effects of unit failures in each power plant as one unit. Therefore, the present investigative study has begun from discussing the achievement of energy conservation and reduction of greenhouse gas emission by managing the demand and supply in an economical manner upon introducing a central load dispatching center (CLDC). Given the introduction of CLDC, the effects of introducing the equi-{lambda} method with still higher economy and of introducing the control system of reserve operation power may be summarized as follows: the energy saving effects (converted to crude oil quantity) are 22,400 toe/year for the former case and 35,800 toe/year for the latter case; and the greenhouse gas reduction effects are 52,000 t-CO2/year for the former case and 84,000 t-CO2/year for the latter case. This is an effective project with a considerable amount of effect as a result of introducing the equi-{lambda} and of introducing the control system of reserve operation power, while the investment amount is relatively small. The investment recovery period is 2.5 years and 2 years, respectively, making the project considerably promising as a CDM project. (NEDO)

  5. Systems

    International Nuclear Information System (INIS)

    Anon.

    1980-01-01

    Papers in this session describe the concept of mined geologic disposal system and methods for ensuring that the system, when developed, will meet all technical requirements. Also presented in the session are analyses of system parameters, such as cost and nuclear criticality potential, as well as a technical analysis of a requirement that the system permit retrieval of the waste for some period of time. The final paper discusses studies under way to investigate technical alternatives or complements to the mined geologic disposal system. Titles of the presented papers are: (1) Waste Isolation System; (2) Waste Isolation Economics; (3) BWIP Technical Baseline; (4) Criticality Considerations in Geologic Disposal of High-Level Waste; (5) Retrieving Nuclear Wastes from Repository; (6) NWTS Programs for the Evaluation of Technical Alternatives or Complements to Mined Geologic Repositories - Purpose and Objectives

  6. systems

    Directory of Open Access Journals (Sweden)

    Alexander Leonessa

    2000-01-01

    Full Text Available A nonlinear robust control-system design framework predicated on a hierarchical switching controller architecture parameterized over a set of moving nominal system equilibria is developed. Specifically, using equilibria-dependent Lyapunov functions, a hierarchical nonlinear robust control strategy is developed that robustly stabilizes a given nonlinear system over a prescribed range of system uncertainty by robustly stabilizing a collection of nonlinear controlled uncertain subsystems. The robust switching nonlinear controller architecture is designed based on a generalized (lower semicontinuous Lyapunov function obtained by minimizing a potential function over a given switching set induced by the parameterized nominal system equilibria. The proposed framework robustly stabilizes a compact positively invariant set of a given nonlinear uncertain dynamical system with structured parametric uncertainty. Finally, the efficacy of the proposed approach is demonstrated on a jet engine propulsion control problem with uncertain pressure-flow map data.

  7. Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir change prediction technology (Development of modelling support technology); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (choryuso hendo yosoku gijutsu (modeling shien gijutsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The aim is to develop and popularize techniques relating to geological information such as thermal history. The efforts center about the application of a now-available core fracture measuring system to developed geothermal fields and about the development of new technologies. The measuring system is applied to some core cuttings collected from five boreholes in the Akinomiya district, Akita Prefecture, and the system is used for (1) the evaluation of homogenization temperatures of inclusions in the fluid, (2) the measurement of the points of melting from ice of inclusions in the fluid, and (3) the implementation of laser Raman spectroscopy. Under item (1), it is found that the minimum homogenization temperature of quartz phenocryst in the mother rock or of low-salinity fluid inclusion in a quartz vein is near the current subsurface temperature and that subsurface and reservoir temperatures may be known by evaluating their homogenization temperature. Under item (2), it is found that the NaCl equivalent salinity is distributed in the range of 0.0 to 25wt% and that, in this connection, there is difference between a fluid in a fluid flow and a fluid spurting as thermal water in the Akinomiya district. Under item (3), CO2, N{sub 2}, and CH{sub 4} are detected in most of the boreholes. Efforts are exerted to develop a hydrothermal fluid analyzing technique using a rapid rock dating method and traces of chemical ingredients in hydrothermal minerals. (NEDO)

  8. Fiscal 1997 report of the verification research on geothermal prospecting technology. Theme 5-2. Development of a reservoir change prospecting method (reservoir change prediction technique (modeling support technique)); 1997 nendo chinetsu tansa gijutsu nado kensho chosa. 5-2. Choryuso hendo tansaho kaihatsu (choryuso hendo yosoku gijutsu (modeling shien gijutsu)) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To evaluate geothermal reservoirs in the initial stage of development, to keep stable output in service operation, and to develop a technology effective for extraction from peripheral reservoirs, study was made on a reservoir variation prediction technique, in particular, a modeling support technique. This paper describes the result in fiscal 1997. Underground temperature estimation technique using homogenization temperatures of fluid inclusions among core fault system measurement systems was applied to Wasabizawa field. The effect of stretching is important to estimate reservoir temperatures, and use of a minimum homogenization temperature of fluid inclusions in quartz was suitable. Even in the case of no quartz in hydrothermal veins, measured data of quartz (secondary fluid inclusion) in parent rocks adjacent to hydrothermal veins well agreed with measured temperature data. The developmental possibility of a new modeling support technique was confirmed enough through collection of documents and information. Based on the result, measurement equipment suitable for R and D was selected, and a measurement system was established through preliminary experiments. 39 refs., 35 figs., 6 tabs.

  9. FY 1991 report on the results of the development of an entrained bed coal gasification power plant. Part 1. Support study for the development of an entrained bed coal gasification power plant (Dismantling study); 1991 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu (Funryusho sekitan gaska hatsuden plant kaihatsu no shien kenkyu) - Sono 1. Kaitai kenkyu hen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-04-01

    As a support study for the development of an entrained bed coal gasification power plant by a 200 t/d pilot plant, the dismantling study was made for gasifier facilities, desulfurization facilities, dedusting facilities at the existing 40 t/d testing facilities. In the results of the analysis of the specimens sampled from gasifier and peripheral facilities, the corrosion loss of thickness was great in carbon steel/low-alloy steel equipment, and the generation of intergranular corrosion/intergranular crack was recognized in stainless steel equipment. The loss of thickness caused by erosion was also recognized in carrier tubes, etc. As to the high-temperature dry desulfurization system, the damage was totally great, but the effect of taking measures for it was unclear because the loss of thickness by corrosion/abrasion had not been measured regularly. Relating to the high-temperature dry dedusting system, there used to be a lot of troubles from stress corrosion cracking and pitting corrosion, and the best measures for corrosion prevention were taken for each trouble. As to the Al thermal spraying, stabilized thermal treatment, shot-peening, etc., the excellent corrosion prevention effect was recognized on the austenite stainless steel. (NEDO)

  10. FY 2000 Immediate-effect type project for research and development for international standards supporting information technology industries. Comprehensive study on promotion of international standardization; 2000 nendo joho sangyo shien sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The information technology and international standardization are studied for the elementary information technology, mechanical safety areas and electronic trading, aimed at achieving the international standards in a short time for the information industrial sector, which shows rapid technological development. The program for the elementary information technology includes development/standardization of the testing/evaluation methods for transparent electroconductive films for notebook computers, liquid crystal monitors or the like, specifically for the mechanical and physical properties. The program for mechanical safety areas includes definition of the closed space type mechanical safety monitoring techniques and use of safety-confirmation type sensors for the techniques, and standardization of the requirements of the protectors for use of the safety-confirmation type sensors, among others. The program for the electronic trading includes standardization of the electronic catalogues of the instrumentation devices, dictionaries of the instrumentation devices and device-screening processes. The other efforts include development of the applications and system infrastructure functions, construction of the demonstration test systems, and demonstration tests. (NEDO)

  11. Report for fiscal 2000. Part 4. Research on assistance to put recycling technologies into practical use (Research and development of elevating automotive fuel consumption and exhaust gas technologies); 2000 nendo recycle gijutsu nado jitsuyoka shien kenkyu hokokusho. 4. Jidosha nenpi hai gas gijutsu kodoka kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Discussions have been given on identification of actual status of exhaust gas emission during driving, starting, and idling of automobiles, on technologies to enhance fuel consumption and reduce exhaust gas emission, and on technologies to measure harmful substances. In the investigation of effects of environmental temperatures on evaporation gas, it was shown that fuel evaporation generated from the fuel tank increases as the average ambient temperature rises. In the investigation of effects of environmental temperatures on exhaust gas and fuel consumption, it was discovered that the effects of environmental temperatures on 10{center_dot}15 mode regulated exhaust gas differ depending on vehicles, and no definite difference due to combustion systems was recognized. Carbon monoxide and THC under the 11 mode regulation showed a trend to increase when the environmental temperature falls down. In the investigation of effects of fuel properties on exhaust gas, no definite difference due to combustion systems was recognized as a result of measurements using various types of gasoline having different distillation properties. In the investigation of analysis methods for harmful substances, development has been made on an analysis method mainly for 1-3 butadiene. (NEDO)

  12. Research report of fiscal 1997. Feasibility research on introduction of distributed power sources using new energy (photovoltaic and wind power generation) in the South Pacific; 1997 nendo chosa hokokusho. Minami Taiheiyo ni okeru shin energy (taiyoko, furyoku nado) wo katsuyoshita bunsangata dengen no donyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Feasibility research was made on distributed power sources using photovoltaic and wind power generation in Tonga and Samoa. For the best mix of environment-friendly power sources, hearing from government leaders and power business persons, and field inspection were carried out. Foreign currency earnings of Tonga are dependent on remittance from nations working overseas, while since diesel fuel for power generation is expensive because of import through Fiji and tariffs, multi-power sources for power cost reduction and low-cost new power systems are in expectation. Underground transmission and distribution lines are under consideration to prevent typhoon damages. Both countries are probably rich in wind power potential, however, wind condition data are poor requiring further researches. Tonga government is in charge of power business except that in Tongatapu island. In Samoa, EPC (Electric Power Corp.) is in charge of power business. Hydroelectric power generation is possible because of rivers formed by abundant tropical rains. Feasibility research was made on coal-firing, fuel cell combined, wind power, photovoltaic and waste power generation. 7 figs.

  13. Report on the fiscal 1993 investigational study of the environmental technology development trend in Japan. Trend survey of the introduction policy of environmentally friendly products; 1993 nendo Nippon ni okeru kankyo gijutsu kaihatsu doko nado ni kansuru chosa kenkyu hokokusho. Kankyo chowagata seihin no donyu hosaku nado doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-05-01

    An investigation was conducted into the systematical scheme for the introduction and promotion of environmentally friendly products mostly to the U.S., Europe and China. In the U.S., the introduction policy is given to one and all fields of the industry. The introduction policy of the U.S. has a characteristic that the introduction is left to the market principle by DSM or permit dealing, etc. except the preferential tax system and systematical finance in which the government is concerned. The policy of European countries is characterized by the idea preceding, standards or rules are first given, and the whole is pushed on to them. Accordingly, it seems that there is few atmosphere of expecting to receive the government side economic incentives from the corporate side. Legal regulations on the environment in China were prepared in a comparatively early time (1979), but the supervision of obeying the regulations and the appearance/spread of environmentally friendly product menus have just started. Accordingly, as the introduction policy on environmentally friendly products, there was found nothing valuable but the regulations. 12 refs., 3 figs., 15 tabs.

  14. FY 2000 report on the survey to support the R and D on the development of the coal/natural gas use CO2 recovery/utilization technology; 2000 nendo sekitan tennen gas katsuyogata nisanka tanso kaishu riyo gijutsu no kaihatsu ni kansuru kenkyu kaihatsu shien chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In this study, technology to rationalize energy utilization is developed by which CO2 is efficiently converted into methanol which is the next generation liquid fuel by reacting CO2 with coal, natural gas and steam using solar heat. Together with this study, survey/study are conducted of the trend of the related element technology and the total system technology, trend of the competitive technology, study of comparison with the competitive technology, economical efficiency, possibility of the commercialization, etc. In this report, in Chapter 1, summarized are the trend of the R and D which each country conducts with the aim of using abundant solar energy in the Sun Belt and the trend of other R and D of energy utilization in each country. In Chapter 2, the paper describes the technology that Japan is now developing and the developmental trend of the related technology. In Chapter 3, the methanol supply/demand balance and the related researches were arranged. The most important points in future commercialization of the said technology are the establishment of technology and the economical efficiency. (NEDO)

  15. FY 1993 report on the results of the subsidy project for the Sunshine Project. Development of coal use hydrogen production technology (Support study of pilot plant - Trial development of materials of plant use equipment); 1993 nendo Sunshine keikaku hojo jigyo seika hokokusho. Sekitan riyo suiso seizo gijutsu kaihatsu - Pilot plant no shien kenkyu (Plant yo kiki zairyo no shisaku kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    As to the development of coal use hydrogen production technology, the paper made the test study on the improvement of gasifier use materials and evaluation of the characteristics, the evaluation test in the environment using the actual machine, etc., and the FY 1993 results were reported. The results of the study were as follows. Concerning the shaped refractory for gasifier hearth, it was found that high chromia base and picrochromite base refractory development materials had much more excellent coal slag resistance than other existing component-system materials. It was shown that the development materials began to deteriorate under the coal gasification environment at temperatures of about 1,500 degrees C or higher. As to the mullite ceramics, a possibility was shown of improving the slag permeation resistance by making the crystal grain coarse by long-time sintering. By the survey of the state of damage of the proposed materials (refractory and iridium) used in the operational environment of the pilot plant, the outlook for use limit was made clear. In the environment test using the actual machine on the proposed metal base alloy of the typical equipment of the pilot plant, the correspondence between the operational environment and material corrosion was made clear. (NEDO)

  16. FY 1991 report on the results of the development of an entrained bed coal gasification power plant. Part 2. Support study for the development of an entrained bed coal gasification power plant (Summarization of the operation study); 1991 nendo seika hokokusho. Funryusho sekitan gaska hatsuden plant kaihatsu (Funryusho sekitan gaska hatsuden plant kaihatsu no shien kenkyu) - Sono 2. Unten kenkyu sokatsu hen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-04-01

    The paper summarized the results of the following tests on a 40 t/d pilot plant which were conducted as the support study for the development of an entrained bed coal gasification power plant: dry desulfurization test, dry dedusting test, high-temperature NOx gas combustion test (gas turbine element test). In the dry desulfurization test, tested were the operational automation and monitoring technology, performance of desulfurization, characteristics of load response, sulfur recovery, etc. In the dry dedusting test, tested were the filter medium/dust separation, powder level meter, continuous dust densitometer, operational automation, characteristics of partial load/load response, improvement of filtration materials, test on characteristics of air conveyance, etc. In the high-temperature low-NOx gas combustion test (gas turbine element test), the following were conducted: examination of the test method of gas turbine materials, inspection/examination of the corrosion of gas turbine combustion test device, inspection/examination of the internal corrosion of the stationary blade for gas turbine deposit test, inspection/examination of gasification system. The results of these support studies were reflected one after another in the project on the development of an entrained bed coal gasification power plant. (NEDO)

  17. New energy introduction guidebook for Chugoku area; Shin energy donyu guidebook. Chugoku chiiki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-05

    A guidebook was edited for the purpose of assisting introduction of new energies. Sections consist of Section 1, new energies available in the Chugoku area; Section 2, procedure for new energy introduction; Section 3, assistance institutions by energy; and Section 4, the status of new energy introduction in the Chugoku area, the future introduction targets, and referential materials. Section 1, upon defining the new energies, summarized features of photovoltaic power generation, solar heat utilization, wind power generation, wastes power generation, cogeneration, fuel cells, clean energy fueled automobiles, and introduction records up to the year 2000. Section 2 summarizes the general roles of local governments in the introduction, processing procedures for individual programs, related regulations, and summary of the assistance institutions. Section 3 puts into order the assistance institutions by energy. Section 4 summarizes precautions, targets and records in introduction by each new energy. The referential materials include a list of the Japanese assistance institutions, and subsidy institutions related to new energies for local governments in the Chugoku area. (NEDO)

  18. New energy introduction vision in Chiba Prefecture; Chibaken shin energy donyu vision

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Surveys and discussions were given on establishing a new energy introduction vision in Chiba Prefecture. The basic conception for new energy introduction regarded important the handling of global environment problems, improvement of the global environment, enhancement in energy security, and assurance of the regional performance of disaster prevention. New energy introduction is thought making it possible to create attractive urban spaces, make living environment more agreeable, and promote and breed new industries including the eco-business. Important measures may include the followings: introduction of new and economic energies in multiple ways for individual buildings and facilities, development of environment symbiotic cities utilizing new energies, improvement of region symbiotic cities in industrial zones, effective utilization of energies from wide-area refuses and wastes, establishment of an urban type cleaning plant that utilizes effectively energies from general wastes, new energy utilization in coordination with agricultural activities, utilization of new energies in fishery industry areas, and expansion in use of clean energy fueled automobiles including natural gas fueled automobiles. (NEDO)

  19. SYSTEM

    Directory of Open Access Journals (Sweden)

    K. Swarnalatha

    2013-01-01

    Full Text Available Risk analysis of urban aquatic systems due to heavy metals turns significant due to their peculiar properties viz. persis tence, non-degradab ility, toxicity, and accumulation. Akkulam Veli (AV, an urba n tropical lake in south India is subjected to various environmental stresses due to multiple waste discharge, sand mining, developmental activities, tour ism related activitie s etc. Hence, a comprehensive approach is adopted for risk assessment using modified degree of contamination factor, toxicity units based on numerical sediment quality guidelines (SQGs, and potentialecological risk indices. The study revealed the presence of toxic metals such as Cr, C d, Pb and As and the lake is rated under ‘low ecological risk’ category.

  20. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Final year report. Development of the measuring control technology supporting energy conservation in the manufacturing process of electronics (Design and trial manufacture of IMI); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Denshi kikirui seizo process no sho energy shien keisoku seigyo gijutsu no kaihatsu - IMI no sekkei to shisaku (saishu nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As measures taken for energy conservation in the manufacturing plant of electronic devices/equipment such as IC, the development was proceeded with a chlorine gas radio sensing system and a liquid crystal driver IC probe, according to the survey results that it is possible to control energy consumption in air conditioning by completely furnishing poisonous gas monitor in clean room and conserve energy related to the manufacture of IC and LSI tester by using Si for IC probe cards. The following four were carried out: 1) development/trial manufacture of chlorine sensing system; 2) development/trial manufacture of LCD (liquid crystal driver) IC probe; 3) support of trial manufacture of key element technology; 4) comprehensive investigational study of IMI (Intelligent Micro-Instrument). In FY 2000, study was focused on 1) and 2). In 1), a planar type micro-structure sensor was developed, and the trial-manufactured system brought favorable results in sensitivity, response speed and reproductivity. (NEDO)

  1. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium research and development of energy in its 2nd year (Development of energy conservation assisting measurement control technology for electronic equipment manufacturing process--Designing and tentative construction of IMI); 1999 nendo denshi kikirui seizo process no sho energy shien keisoku seigyo gijutsu no kaihatsu seika hokokusho. 2. IMI no sekkei to shisaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the research and development of IMI (intelligent micro instrument) substrate devices, a designing method is established and, using the method, device manufacturing technologies are tested and evaluated and the results are reflected on the experimental construction of a sensor and an IC probe. In the research and development of a sensor and a sensing system, efforts are focused on a chlorine gas sensor, and a prototype No. 1 is designed and fabricated. In a test conducted in the presence of gas of 0-10ppm concentration, the prototype transmits signals that indicate excellent linearity and responsiveness. In the research and development of a probe for measuring electronic devices, efforts are made to put to practical use an IC (integrated circuit) probe of 40{mu}m pitch times 400 arrays, and specifications to develop for the probe are defined. A tentatively built cantilever structure shows values that justify its practical application. In the research and development of an IMI electronic circuit, a prototype No. 1 of a system for processing and transmitting sensor signals by radio is manufactured, which operates on the carrier frequency of 2.4GHz and sampling frequency of 4kHz. The prototype performs to achieve the goal. (NEDO)

  2. Fiscal 1999 edition. Guidebook for introducing new energies in Kinki District; Kinki chiiki shin energy donyu guide book

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    The captioned guidebook is composed of the following subjects: (1) the current status and problems of new energies (the energy status and the current status of new energies in Japan, and approaches to new energies in Japan); (2) the status of introduction and works in Kinki District (the outline of introduction and works in Kinki District on photovoltaic electric power generation, solar heat utilization, wind power generation, wastes power generation, clean energy fueled automobiles, cogeneration, fuel cells, unused energies, and other reproducible energies); (3) NEDO related supportive institutions (new energy introduction promotion projects by NEDO, and the outline of different supportive institutions); (4) new energy introduction flow (total flow leading to the introduction, and introduction flow by new energies); (5) the grand new energy prize in Kinki District (what is the grand new energy prize? and cases of prizes awarded in Kinki District); (6) new energy related supportive institutions (a list of the related institutions, and the outline of different supportive institutions); and (7) new energy consultation windows and contacts (consultation windows and contacts for general new energy aspects and the government related supportive institutions, and consultation windows by new energies). The grand new energy prize is awarded by New Energy Foundation as the 'institution for public recognition of new energy devices of the 21st century type'. (NEDO)

  3. Fiscal 1999 edition. Guidebook for introducing new energies in Kinki District; Kinki chiiki shin energy donyu guide book

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    The captioned guidebook is composed of the following subjects: (1) the current status and problems of new energies (the energy status and the current status of new energies in Japan, and approaches to new energies in Japan); (2) the status of introduction and works in Kinki District (the outline of introduction and works in Kinki District on photovoltaic electric power generation, solar heat utilization, wind power generation, wastes power generation, clean energy fueled automobiles, cogeneration, fuel cells, unused energies, and other reproducible energies); (3) NEDO related supportive institutions (new energy introduction promotion projects by NEDO, and the outline of different supportive institutions); (4) new energy introduction flow (total flow leading to the introduction, and introduction flow by new energies); (5) the grand new energy prize in Kinki District (what is the grand new energy prize? and cases of prizes awarded in Kinki District); (6) new energy related supportive institutions (a list of the related institutions, and the outline of different supportive institutions); and (7) new energy consultation windows and contacts (consultation windows and contacts for general new energy aspects and the government related supportive institutions, and consultation windows by new energies). The grand new energy prize is awarded by New Energy Foundation as the 'institution for public recognition of new energy devices of the 21st century type'. (NEDO)

  4. Data book of new energy introduction to Hokkaido. FY 2000 version; Hokkaido shin energy donyu data shu. 2000 nendoban

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of effectively introducing/promoting new energy and of supplying the basic data which contribute to the promotion/education, the actual results of new energy introduction to Hokkaido were collected/arranged. New energies to be surveyed were the photovoltaic power generation, solar heat utilization, wind power generation, waste power generation, waste heat utilization, waste fuel production, biomass energy, unused energy, gas generation, petroleum cogeneration, fuel cells, clean energy vehicles, small-/medium-scale hydroelectric power generation, etc. The purpose of the book is mainly to collect the basic information, that is, what kind of new energy has been introduced to what kind of area. The data are so collected that facilities adopting new energy can be seen as unit of city/town/village as a rule. The method to collect information is based on the total collection of the reports made by organizations in/outside Hokkaido. The book additionally covers the details of the data supplied and the data collected. (NEDO)

  5. Investigation into introduction and promotion of clean energy cars; Clean energy jidosha no donyu sokushin ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Gazing the introduction target for fiscal 2000 and 2010, the paper arranged comprehensively and systematically the trend in Japan and overseas of clean energy cars and described subjects. Themes of the study to be promoted in terms of electric cars are: Li secondary batteries, heightening of performance of batteries such as Ni-hydrogen, power generation/power storage hybridization to make the long-distance travel possible. For the price reduction, the body is so made as to make it possible to select three kinds of power unit, that is, gasoline, hybrid, and electricity. Low noise and easy operation are also important. As to natural gas vehicles, the price is more than three times as high as that of gasoline vehicles, and relaxation of the related regulations on metal tanks, the Road Traffic Act, etc. is necessary. It is indispensable to establish quantity production and technical standards and reduce cost by the remodeling for bi-fueling with gasoline engines, development of FRP tanks, etc. Methanol vehicles are the closest to gasoline vehicles, but the introduction is delayed having no groups for generalization. Solar and hydrogen cars are promising, but are on a stage of developing the basic technology. 43 figs., 104 tabs.

  6. Effects of peak shaving technologies in the residential and commercial sector; Minsei bumon no fuka heijunka gijutsu no donyu koka

    Energy Technology Data Exchange (ETDEWEB)

    Nagata, Y. [Kyoto University, Kyoto (Japan); Takahashi, M.; Uchiyama, Y. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-09-01

    This paper analyzes how much of the power demand could be reduced in the future by improving efficiencies of electric power utilizing appliances used in the residential and commercial sector. It discusses whether the reduction would lead to load leveling. Annual load rate in the power demand is continuing to decrease because of power demand increase in the residential and commercial sector, and increase in demand for air conditioning in summer. If a technology to improve electric appliance efficiency is proliferated to its maximum scope, the annual load rate in fiscal 2014 may be improved by 1.1 percent point. Since the improvement allows new power generation facility installation cost to be deferred, the power generation unit cost can be reduced by 0.11 yen per kwh. If a heat storage type air conditioning technology is proliferated to its maximum scope, the annual load rate in fiscal 2014 can be improved by 1.8 percent point, and the power generation cost may also be reduced. If the device efficiency improving technology and the heat storage type air conditioning technology are introduced to their maximum simultaneously, the annual load rate in fiscal 2014 can be improved by 2.5 percent point, and the power generation cost may also be reduced by 0.24 yen per kwh. If a promotion policy is taken on proliferation of a specific device efficiency improving technology having excellent economic performance by providing subsidy, the reduction amount of cumulative power generation expense will be much greater than the required subsidy amount. 10 refs., 9 figs., 22 tabs.

  7. Making of composite type energy introduction models in cities; Toshi ni okeru fukugogata energy donyu model no sakusei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper made and studied simulation models in case of introducing new energy of composite type to cities. In the study, using a standard composition unit of city as a cluster, the compositional element was divided into 25 cells, which were divided into the residence superiority cell and the business superiority cell. The residence superiority cell was divided into highrise and lowrise. The calculation program is to simulate effects of introducing new energy such as the photovoltaic power generation, solar energy utilization, waste power generation, cogeneration, and unused energy like river water and waste water. Using the program, the analysis of sensitivity was conducted concerning how the outputs will change according to differences in energy consuming composition in the urban area. The calculation was conducted concerning local cities of the warm area, local cities of the cold area, local cities of the subtropical area, residence/working-place neighboring core cities in the warm area, central areas of large cities of the warm area, and new towns of the warm area. 28 figs., 27 tabs.

  8. FY 1999 data book for the introduction of new energy to Hokkaido; 1999 nendoban Hokkaido shin energy donyu data shu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of effectively promoting the introduction of new energy to Hokkaido, it is necessary to comprehensively/systematically arrange various kinds of new energy and to furnish the basic data which contribute to the spread/education. The paper collected/arranged the actual results of the introduction of new energy to Hokkaido, using the existing data, etc. Attention is paid to the collection of the basic information on what kinds of new energy have been introduced in what kinds of regions, etc. Fundamentally, the data were collected by which facilities for new energy can be seen by city/town/village. The new energy for collection is basically within the range of those included in the New Energy Law. They are renewable energy (photovoltaic power generation, solar heat utilization, and wind power generation); recycle type energy (waste power generation, waste heat utilization, fuel production, waste fuel production, biomass energy, and unused energy); new forms of the existing energy (gas/oil cogeneration, fuel cell, and clean energy vehicle). (NEDO)

  9. Plan to promote new energy introduction in Niigata Prefecture area; Niigataken chiiki shin energy donyu suishin keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The 'Plan to promote new energy introduction in Niigata Prefecture area' was established to leave the conditions that everybody can live with affluence and comfort in the next generation. The plan lasts for ten years until 2010. Upon identifying the district characteristics of Niigata Prefecture, and based on the results of investigations on new energy existence quantity, utilization possibility thereof, and consciousness of residents of the prefecture, considerations were given that the plan shows the basic policy to promote proliferation of the new energies, and serves as the guideline for practical implementation. The plan document is composed of the following four items: 1) the foreword, 2) the current status of energies, 3) new energies expected of introduction, and 4) basic measures. The energy consumption was estimated to increase to 1.345 times that of fiscal 1990 in the year 2010, the increase being mainly in consumer and household use. The targeted quantity for new energy introduction was set to 90,000 kl annually as converted to petroleum. Expected new energy applications would include photovoltaic power generation, snow energy and solar heat utilization, and cogeneration utilizing natural gas. (NEDO)

  10. System Budgets

    DEFF Research Database (Denmark)

    Jeppesen, Palle

    1996-01-01

    The lecture note is aimed at introducing system budgets for optical communication systems. It treats optical fiber communication systems (six generations), system design, bandwidth effects, other system impairments and optical amplifiers.......The lecture note is aimed at introducing system budgets for optical communication systems. It treats optical fiber communication systems (six generations), system design, bandwidth effects, other system impairments and optical amplifiers....

  11. Survey of the waste-fueled power generation introducing technology. Case study 1 (fiscal 1996); Haikibutsu hatsuden donyu gijutsu chosa nado. Case study no jisshi 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A case study on A city was conducted aiming at making a detailed manual for introducing the waste-fueled power generation. The study was made in terms of a large-capacity waste-fueled power plant, estimation of the waste amount considering wide-area processing, size of facilities, comparison of four types of combustion furnace, steam condition/seawater cooling/power generating efficiency, etc. As a result, the following were proposed: As to the size of facilities, a capacity as large as possible is recommended in the light of the scale merit of costs of the waste-fueled power plant and final disposal site and the environmental preservation. Concerning the high efficient power generation, recommended are 450degC and 60-80 ata which are steam conditions for coping with high temperature corrosion. In respect to seawater cooling, the adoption is recommended making good use of locational conditions since the output energy increases by approximately 16%. Any furnace types including the fluidized bed furnace are equal. The amount of dioxin becomes below 0.1ng/Nm{sup 3} because of the control of furnace combustion temperature, residence time, catalytic desulfurization facilities, blowing of activated coal into the flue, etc. 172 figs., 78 tabs.

  12. Evaluation report on the R and D of the membrane separation process introduction technology; Makubunri process donyu gijutsu no kenkyu kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper reported the R and D of the membrane separation process introduction technology during a period of 1994 through 1998. The membrane separation technology is not associated with the phase change which requires large energy and expected to be an energy saving process. For the production of membranes required of high functions, the vapor deposition polymerization method was considered, and high order structure control of the membrane, control of adhesion and attachment, and control of orientation, and development of the high polymerization technology were required. For the high grade control of vapor polymerization, the substrate surface structure/quality were important. The molecular level analysis of the vapor deposition surface was also needed. Therefore, the paper took notice of STM (scanning tunneling microscopy), AFM (atomic force microscopy) and HREELS (high resolution electron energy loss spectroscopy) as surface atomic/molecular configuration analysis technology, and designed/fabricated and studied the high resolving power and high sensitivity analysis equipment using the analysis equipment which combined HREELS and STM and the analysis equipment using SFG (sum frequency generation) which can detect signals in the low frequency region. Making full use of the highest technology, technology was able to be developed for substrate surface analysis and surface reaction analysis technologies which become the basis of the high performance separation membrane fabrication technology by the vapor deposition polymerization method indispensable for introduction of the membrane separation process. The technology can be the base applicable to a lot of fields where surfaces and interfaces are concerned

  13. New energy vision for Oita Prefecture. Toward the adoption of eco-energy; 2001 nendo Oita ken shin energy vision. Eco energy no donyu ni mukete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For contributing to the preservation of the global environment, studies were made to work out a new energy introduction vision fully exploiting the characteristic features of Oita Prefecture. Oita Prefecture's demand for energy in 1998 is estimated to be 408.6 times 10{sup 15} J, with coal-based energy covering 204,016 TJ, oil-based energy 160,192 TJ, electric power 37,721 TJ, and so forth. The consumption will result in the emission of 35.77 million tons of carbon dioxide. According to Oita Prefecture's prospect of its eco-energy adoption in 2010, there will be 319 MW from hydroelectric power, 155 MW from geothermal power, 52 MW from photovoltaic power, 46 MW from clean energy vehicles, 33 MW from refuse-fueled power, and so forth. To prepare plans for facilities to utilize eco-energy and for regional development in the future through the use of such facilities, introduction costs were predicted and effects were simulated for model businesses engaged in biomass power generation using livestock wastes, small-scale hydroelectric power generation, bio-diesel fuel production, wind power generation, and woody biomass power generation. (NEDO)

  14. FY 1998 survey report on the project on field tests for high-efficient industrial furnace introduction. Manual; 1998 nendo koseino kogyoro donyu field test jigyo mannual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The high-efficient industrial furnace is a technology with the use of ultra-high temperature air over 1,000 degrees C, which has been impossible. It has been developed since FY 1993. The technology can reduce the energy consumption amount by 30%, and there is a possibility of reducing not only CO2, but NOx by approximately 50% over the conventional method. The main technique of the technology is to preheat the air blown into the incinerator at much higher temperatures of 1,000 degrees C or more than those in the existing combustion and to blow fuel into that high-speed air flow using the short-time-change/heat-storage type heat exchanger. It was predicted that the target value set first can almost be reached, and there can be seen a possibility of its industrial application. Industrial furnaces are used in many industrial fields such as metal production industry, petrochemical industry and electric machinery industry. The energy conservation in these fields brings extremely marked effects, and therefore it is an urgent task to introduce the industrial furnace into the fields quickly. The concentrated R and D were finished in FY 1998, and the field test project for the introduction was actually started. (NEDO)

  15. FY 1990 achievement report on the survey of possibility of introducing solar energy into buildings; 1990 nendo taiyo energy no kenchikubutsu eno donyu kanosei chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    This paper describes the achievements in fiscal 1990 on survey on possibility of introducing solar energy into buildings. Capacity of photovoltaic power generation facilities installed on an area of 1600 km{sup 2}, such as roofs of residential houses, schools and building may be calculated on a trial bases as 100 million kW at maximum. The capacity can replace 16% of the total demand and corresponds to 26.30 million kiloliters (9%) as converted to crude oil. If photovoltaic power generation is utilized on buildings of users, diversified technological criteria are required from the viewpoint of legislation covering wide range of architectural, electrical and disaster aspects. However, no direct and clear standards are available now, except for the electric power business law. What are urgently required are solar cell standardization, incentive subsidies, aging safety, institutions for electric power sale and purchase, and establishment of technological criteria. An utilization example survey revealed problems in array installation and size. Increased demand, mass production and cost reduction will create a favorable cycle. Introduction, proliferation, and acceleration under policies at public facilities which are expected of enlightenment and development into other areas will be the effective means for the purpose. (NEDO)

  16. FY 2000 research cooperation project on the support for heightening of capability of research institutes; 2000 nendo kenkyu kyoryoku jigyo. Kenkyu kikan noryoku kojo shien

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of supporting the heightening of capability of research institutes in the following 7 countries, China, Thailand, Malaysia, Indonesia, the Philippines, India and Vietnam, exchanges/guidance/training were conducted by sending researchers from Japan and inviting researchers to Japan. Japanese researchers were sent for the following: cleaner technology in fiber dyeing finish (Thailand), 3 cases including the survey of the actual state of underground water pollution caused by harmful pharmaceuticals (the Philippines), 2 cases including the energy recovery in the fiber dyeing industry (Indonesia), making of energy management rules in the industrial field (Malaysia), spread of the photovoltaic power generation to areas where there is no electricity service in Tibet (China), 3 cases including the personnel development in the environmental management field of electric power companies (India), and 2 cases including the information exchange program in the energy conservation field (Vietnam). A total of 74 researchers were invited to Japan, that is, to the environmental protection training course of Japan. (NEDO)

  17. Basic studies on computer aided concurrent engineering for hull structure design and piping design; Kakugi ittai wo koryoshita doji heikotekina sekkei no shien ni kansuru kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Aoyama, K.; Sawada, K. [The University of Tokyo, Tokyo (Japan)

    1996-12-31

    Considering integrated hull and piping design in shipbuilding industry as a good example for concurrent engineering (CE), discussions were given on a computer aided method to perform integrated hull and piping design smoothly. When CE aiding by means of a computer is considered, it is important to discuss a method for information management not only for `utilization of product models`, but also for `maintaining consistency between items of product information` and `concurrent utilization and production of product information` in concurrent designs. For the CE aided information management, utilization and production of the product information is effective if restrictive relationship between items of product information, and design functions are made clear. Definitions were given on the restrictive relationship between items of product information and `restrictive relationship information` that has `decision/provisional decision`, `date and time`, `designer` and `design functions`. Furthermore, `comprehensive relationship between items of product information` that can be produced from the restrictive relationship information was defined as a `restrictive network`. Utilizing the restrictive relationship between items of product information for CE aiding is effective. 9 refs., 14 figs.

  18. FY1998 report on the research on support for practical recycling technologies. Part 1; 1998 nendo recyle gijutsu nado jitsuyoka shien kenkyu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This project aims at development, demonstration and utilization of waste recycling technologies. This report summarizes the fiscal 1998 results. The test/demonstration plant for separation and removal of foreign materials was constructed for effective use of waste building wood, and its optimum operation condition was studied. Although some foreign materials exists, 90% of waste building wood chips were separated and recovered through some improvements for the plant. An advanced separation technology is expected. As for fibering technology, fibers with target compression strength were obtained from cedar chips through a disintegration experiment using a newly developed refiner plate. Although the compression strength of fibers obtained from waste building wood chips was slightly poor, it is attained by increasing the target specific gravity of light- weight wooden materials by nearly 10% from 0.1. As for fiber orientation technology, as the tension of a forming belt was adjusted to achieve sufficient width compression, nearly 90% of the target compression strength was attained. A width compression method remains to be solved. (NEDO)

  19. Basic studies on computer aided concurrent engineering for hull structure design and piping design; Kakugi ittai wo koryoshita doji heikotekina sekkei no shien ni kansuru kisoteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Aoyama, K; Sawada, K [The University of Tokyo, Tokyo (Japan)

    1997-12-31

    Considering integrated hull and piping design in shipbuilding industry as a good example for concurrent engineering (CE), discussions were given on a computer aided method to perform integrated hull and piping design smoothly. When CE aiding by means of a computer is considered, it is important to discuss a method for information management not only for `utilization of product models`, but also for `maintaining consistency between items of product information` and `concurrent utilization and production of product information` in concurrent designs. For the CE aided information management, utilization and production of the product information is effective if restrictive relationship between items of product information, and design functions are made clear. Definitions were given on the restrictive relationship between items of product information and `restrictive relationship information` that has `decision/provisional decision`, `date and time`, `designer` and `design functions`. Furthermore, `comprehensive relationship between items of product information` that can be produced from the restrictive relationship information was defined as a `restrictive network`. Utilizing the restrictive relationship between items of product information for CE aiding is effective. 9 refs., 14 figs.

  20. Ventilation systems

    International Nuclear Information System (INIS)

    Gossler

    1980-01-01

    The present paper deals with - controlled area ventilation systems - ventilation systems for switchgear-building and control-room - other ventilation systems for safety equipments - service systems for ventilation systems. (orig./RW)

  1. Embedded Systems

    Indian Academy of Sciences (India)

    Embedded system, micro-con- troller ... Embedded systems differ from general purpose computers in many ... Low cost: As embedded systems are extensively used in con- .... operating systems for the desktop computers where scheduling.

  2. Thermal systems; Systemes thermiques

    Energy Technology Data Exchange (ETDEWEB)

    Lalot, S. [Valenciennes Univ. et du Hainaut Cambresis, LME, 59 (France); Lecoeuche, S. [Ecole des Mines de Douai, Dept. GIP, 59 - Douai (France)]|[Lille Univ. des Sciences et Technologies, 59 - Villeneuve d' Ascq (France); Ahmad, M.; Sallee, H.; Quenard, D. [CSTB, 38 - Saint Martin d' Heres (France); Bontemps, A. [Universite Joseph Fourier, LEGI/GRETh, 38 - Grenoble (France); Gascoin, N.; Gillard, P.; Bernard, S. [Laboratoire d' Energetique, Explosion, Structure, 18 - Bourges (France); Gascoin, N.; Toure, Y. [Laboratoire Vision et Robotique, 18 - Bourges (France); Daniau, E.; Bouchez, M. [MBDA, 18 - Bourges (France); Dobrovicescu, A.; Stanciu, D. [Bucarest Univ. Polytechnique, Faculte de Genie Mecanique (Romania); Stoian, M. [Reims Univ. Champagne Ardenne, Faculte des Sciences, UTAP/LTM, 51 (France); Bruch, A.; Fourmigue, J.F.; Colasson, S. [CEA Grenoble, Lab. Greth, 38 (France); Bontemps, A. [Universite Joseph Fourier, LEGI/GRETh, 38 - Grenoble (France); Voicu, I.; Mare, T.; Miriel, J. [Institut National des Sciences Appliquees (INSA), LGCGM, IUT, 35 - Rennes (France); Galanis, N. [Sherbrooke Univ., Genie Mecanique, QC (Canada); Nemer, M.; Clodic, D. [Ecole des Mines de Paris, Centre Energetique et Procedes, 75 (France); Lasbet, Y.; Auvity, B.; Castelain, C.; Peerhossaini, H. [Nantes Univ., Ecole Polytechnique, Lab. de Thermocinetiquede Nantes, UMR-CNRS 6607, 44 (France)

    2005-07-01

    This session about thermal systems gathers 26 articles dealing with: neural model of a compact heat exchanger; experimental study and numerical simulation of the thermal behaviour of test-cells with walls made of a combination of phase change materials and super-insulating materials; hydraulic and thermal modeling of a supercritical fluid with pyrolysis inside a heated channel: pre-dimensioning of an experimental study; energy analysis of the heat recovery devices of a cryogenic system; numerical simulation of the thermo-hydraulic behaviour of a supercritical CO{sub 2} flow inside a vertical tube; mixed convection inside dual-tube exchangers; development of a nodal approach with homogenization for the simulation of the brazing cycle of a heat exchanger; chaotic exchanger for the cooling of low temperature fuel cells; structural optimization of the internal fins of a cylindrical generator; a new experimental approach for the study of the local boiling inside the channels of exchangers with plates and fins; experimental study of the flow regimes of boiling hydrocarbons on a bundle of staggered tubes; energy study of heat recovery exchangers used in Claude-type refrigerating systems; general model of Carnot engine submitted to various operating constraints; the free pistons Stirling cogeneration system; natural gas supplied cogeneration system with polymer membrane fuel cell; influence of the CRN coating on the heat flux inside the tool during the wood unrolling process; transport and mixture of a passive scalar injected inside the wake of a Ahmed body; control of a laser welding-brazing process by infrared thermography; 2D self-adaptative method for contours detection: application to the images of an aniso-thermal jet; exergy and exergy-economical study of an 'Ericsson' engine-based micro-cogeneration system; simplified air-conditioning of telephone switching equipments; parametric study of the 'low-energy' individual dwelling; brief synthesis of

  3. Data Systems vs. Information Systems

    OpenAIRE

    Amatayakul, Margret K.

    1982-01-01

    This paper examines the current status of “hospital information systems” with respect to the distinction between data systems and information systems. It is proposed that the systems currently existing are incomplete data dystems resulting in ineffective information systems.

  4. EXPERT SYSTEMS

    OpenAIRE

    Georgiana Marin; Mihai Catalin Andrei

    2011-01-01

    In recent decades IT and computer systems have evolved rapidly in economic informatics field. The goal is to create user friendly information systems that respond promptly and accurately to requests. Informatics systems evolved into decision assisted systems, and such systems are converted, based on gained experience, in expert systems for creative problem solving that an organization is facing. Expert systems are aimed at rebuilding human reasoning on the expertise obtained from experts, sto...

  5. Multibody Systems

    DEFF Research Database (Denmark)

    Wagner, Falko Jens

    1999-01-01

    Multibody Systems is one area, in which methods for solving DAEs are of special interst. This chapter is about multibody systems, why they result in DAE systems and what kind of problems that can arise when dealing with multibody systems and formulating their corresponding DAE system....

  6. NEDO Forum 2000. New energy and energy conservation introducing and proliferating project session (toward promotion of introducing new energies and energy conservation); Shin'ene shoene donyu fukyu jigyo session. Shin'ene shoene no donyu sokushin ni mukete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    The following themes were presented at this session: (1) the history and roles of the NEDO's introduction and promotion projects, (2) expectation and prospects to introduction and promotion of new energy and energy conservation technologies, (3) energy innovation in houses and buildings actively using new energies and energy conservation means, (4) works on introducing new energies by using the private finance initiative (PFI), and (5) the last resort for energy conservation promoting measures in the industrial domain (high-performance industrial furnace technologies). In Item 3, design cases intended for sustainable buildings were introduced. In Item 4, the PFI is explained as a means to use as much fund and management know-how in private sectors as possible in improving the social capitals and providing high-quality public services. In Japan, the PFI promotion law was established in July 1999 (the law concerning promotion of improvements in public facilities by utilizing funds in private sectors). Introductions are given on the wide area wastes disposal project in Kimitsu Area, the PFI model project for power generation of everyday use at Kanamachi Water Purification Plant of the Tokyo Metropolitan Water Supply Bureau, and the Omuta RDF power generation project. In Item 5, descriptions are given on a new high-performance industrial furnace using the combustion mechanism of 'high-temperature air combustion' created from preheated air at temperatures higher than spontaneous combustion temperature. (NEDO)

  7. System dynamics

    International Nuclear Information System (INIS)

    Kim, Do Hun; Mun, Tae Hun; Kim, Dong Hwan

    1999-02-01

    This book introduces systems thinking and conceptual tool and modeling tool of dynamics system such as tragedy of single thinking, accessible way of system dynamics, feedback structure and causal loop diagram analysis, basic of system dynamics modeling, causal loop diagram and system dynamics modeling, information delay modeling, discovery and application for policy, modeling of crisis of agricultural and stock breeding products, dynamic model and lesson in ecosystem, development and decadence of cites and innovation of education forward system thinking.

  8. Coupling component systems towards systems of systems

    OpenAIRE

    Autran , Frédéric; Auzelle , Jean-Philippe; Cattan , Denise; Garnier , Jean-Luc; Luzeaux , Dominique; Mayer , Frédérique; Peyrichon , Marc; Ruault , Jean-René

    2008-01-01

    International audience; Systems of systems (SoS) are a hot topic in our "fully connected global world". Our aim is not to provide another definition of what SoS are, but rather to focus on the adequacy of reusing standard system architecting techniques within this approach in order to improve performance, fault detection and safety issues in large-scale coupled systems that definitely qualify as SoS, whatever the definition is. A key issue will be to secure the availability of the services pr...

  9. Systems effectiveness

    CERN Document Server

    Habayeb, A R

    1987-01-01

    Highlights three principal applications of system effectiveness: hardware system evaluation, organizational development and evaluation, and conflict analysis. The text emphasizes the commonality of the system effectiveness discipline. The first part of the work presents a framework for system effectiveness, partitioning and hierarchy of hardware systems. The second part covers the structure, hierarchy, states, functions and activities of organizations. Contains an extended Appendix on mathematical concepts and also several project suggestions.

  10. Auxiliary systems

    International Nuclear Information System (INIS)

    Meyer, P.J.

    1981-01-01

    Systems included under the heading ''Reactor Auxillary Systems'' are those immediately involved with the reactor operation. These include the systems for dosing and letdown of reactor coolant, as well as for the chemical dosing, purification and treatment of the reactor coolant and the cooling system in the controlled area. The ancillary systems are mainly responsible for liquid and gaseous treatment and the waste treatment for final storage. (orig.)

  11. Bitcoin System

    Directory of Open Access Journals (Sweden)

    Jan Lánský

    2017-06-01

    Full Text Available Cryptocurrency systems are purely digital and decentralized systems that use cryptographic principles to confirm transactions. Bitcoin is the first and also the most widespread cryptocurrency. The aim of this article is to introduce Bitcoin system using a language understandable also to readers without computer science education. This article captures the Bitcoin system from three perspectives: internal structure, network and users. Emphasis is placed on brief and clear definitions (system components and their mutual relationships. A new system view of the stated terms constitutes author’s own contribution.

  12. JOSHUA system

    International Nuclear Information System (INIS)

    Honeck, H.C.

    1975-04-01

    A major computational system called JOSHUA has been under development at the Savannah River Laboratory since 1968. The JOSHUA System has two major parts: the Operating System and the Application System. The Operating System has been in production use since 1970 and provides data management, terminal, and job execution facilities. The Application System uses these facilities in solving problems in reactor physics and engineering. Features of the Application System are the two-dimensional lattice physics and three-dimensional transient reactor physics capabilities, which have been in use since 1971 and 1974, respectively. The capabilities of the JOSHUA System are summarized, and statistics on size, use, and development effort are provided. (U.S.)

  13. Systems thinking.

    Science.gov (United States)

    Cabrera, Derek; Colosi, Laura; Lobdell, Claire

    2008-08-01

    Evaluation is one of many fields where "systems thinking" is popular and is said to hold great promise. However, there is disagreement about what constitutes systems thinking. Its meaning is ambiguous, and systems scholars have made diverse and divergent attempts to describe it. Alternative origins include: von Bertalanffy, Aristotle, Lao Tsu or multiple aperiodic "waves." Some scholars describe it as synonymous with systems sciences (i.e., nonlinear dynamics, complexity, chaos). Others view it as taxonomy-a laundry list of systems approaches. Within so much noise, it is often difficult for evaluators to find the systems thinking signal. Recent work in systems thinking describes it as an emergent property of four simple conceptual patterns (rules). For an evaluator to become a "systems thinker", he or she need not spend years learning many methods or nonlinear sciences. Instead, with some practice, one can learn to apply these four simple rules to existing evaluation knowledge with transformative results.

  14. Cognitive Systems

    DEFF Research Database (Denmark)

    The tutorial will discuss the definition of cognitive systems as the possibilities to extend the current systems engineering paradigm in order to perceive, learn, reason and interact robustly in open-ended changing environments. I will also address cognitive systems in a historical perspective...... to be modeled within a limited set of predefined specifications. There will inevitably be a need for robust decisions and behaviors in novel situations that include handling of conflicts and ambiguities based on the capability and knowledge of the artificial cognitive system. Further, there is a need...... in cognitive systems include e.g. personalized information systems, sensor network systems, social dynamics system and Web2.0, and cognitive components analysis. I will use example from our own research and link to other research activities....

  15. Crystal Systems.

    Science.gov (United States)

    Schomaker, Verner; Lingafelter, E. C.

    1985-01-01

    Discusses characteristics of crystal systems, comparing (in table format) crystal systems with lattice types, number of restrictions, nature of the restrictions, and other lattices that can accidently show the same metrical symmetry. (JN)

  16. Filter systems

    International Nuclear Information System (INIS)

    Vanin, V.R.

    1990-01-01

    The multidetector systems for high resolution gamma spectroscopy are presented. The observable parameters for identifying nuclides produced simultaneously in the reaction are analysed discussing the efficiency of filter systems. (M.C.K.)

  17. Expert systems

    International Nuclear Information System (INIS)

    Haldy, P.A.

    1988-01-01

    The definitions of the terms 'artificial intelligence' and 'expert systems', the methodology, areas of employment and limits of expert systems are discussed. The operation of an expert system is described, especially the presentation and organization of knowledge as well as interference and control. Methods and tools for expert system development are presented and their application in nuclear energy are briefly addressed. 7 figs., 2 tabs., 6 refs

  18. Expert System

    DEFF Research Database (Denmark)

    Hildebrandt, Thomas Troels; Cattani, Gian Luca

    2016-01-01

    An expert system is a computer system for inferring knowledge from a knowledge base, typically by using a set of inference rules. When the concept of expert systems was introduced at Stanford University in the early 1970s, the knowledge base was an unstructured set of facts. Today the knowledge b...... for the application of expert systems, but also raises issues regarding privacy and legal liability....

  19. Retrofitting Systems

    DEFF Research Database (Denmark)

    Rose, Jørgen

    1997-01-01

    This report gives an overview of the different retrofitting possibilities that are available today. The report looks at both external and internal systems for external wall constructions, roof constructions, floor constructions and foundations. All systems are described in detail in respect to use...... and methods, and the efficiency of the different systems are discussed....

  20. Multifunction system

    International Nuclear Information System (INIS)

    Wauthier, J.; Fiori, R.

    1990-01-01

    The development, the characteristics and the applications of a multifunction system are presented. The system is used on the RBES laboratory pipes, at Marcoule. The system was developed in order to allow, without time loss, the modification of the circuit function by replacing only one component. The following elements form the multifunction system: a fixed base, which is part of the tube, a removable piece, which is inserted into the base, a cover plate and its locking system. The material, chosen among commercial trade marks, required small modifications in order to be used in the circuit [fr

  1. Operating systems

    CERN Document Server

    Tsichritzis, Dionysios C; Rheinboldt, Werner

    1974-01-01

    Operating Systems deals with the fundamental concepts and principles that govern the behavior of operating systems. Many issues regarding the structure of operating systems, including the problems of managing processes, processors, and memory, are examined. Various aspects of operating systems are also discussed, from input-output and files to security, protection, reliability, design methods, performance evaluation, and implementation methods.Comprised of 10 chapters, this volume begins with an overview of what constitutes an operating system, followed by a discussion on the definition and pr

  2. Systems integration.

    Science.gov (United States)

    Siemieniuch, C E; Sinclair, M A

    2006-01-01

    The paper presents a view of systems integration, from an ergonomics/human factors perspective, emphasising the process of systems integration as is carried out by humans. The first section discusses some of the fundamental issues in systems integration, such as the significance of systems boundaries, systems lifecycle and systems entropy, issues arising from complexity, the implications of systems immortality, and so on. The next section outlines various generic processes for executing systems integration, to act as guides for practitioners. These address both the design of the system to be integrated and the preparation of the wider system in which the integration will occur. Then the next section outlines some of the human-specific issues that would need to be addressed in such processes; for example, indeterminacy and incompleteness, the prediction of human reliability, workload issues, extended situation awareness, and knowledge lifecycle management. For all of these, suggestions and further readings are proposed. Finally, the conclusions section reiterates in condensed form the major issues arising from the above.

  3. Ternary systems

    International Nuclear Information System (INIS)

    Kagan, D.N.; Hubberstey, P.; Barker, M.G.

    1985-01-01

    The paper reviews the experimental and theoretical studies carried out on multicomponent alkali metal systems. Solid-liquid phase equilibria studies are mainly concerned with the systems Na-K-Rb and Na-K-Cs, and data on the liquidus temperatures in these systems are presented. The thermodynamic properties of the ternary Na-K-Cs eutectic system have been determined experimentally, and the enthalpy, heat capacity and excess functions of the alloy are given. An analysis of calculational methods used in determining thermodynamic functions of ternary liquid metals systems is described. Finally, data are tabulated for the density, compressibility, saturated vapour pressure, viscosity and thermal conductivity of the ternary Na-K-Cs eutectic system. (UK)

  4. Recommender systems

    CERN Document Server

    Kembellec, Gérald; Saleh, Imad

    2014-01-01

    Acclaimed by various content platforms (books, music, movies) and auction sites online, recommendation systems are key elements of digital strategies. If development was originally intended for the performance of information systems, the issues are now massively moved on logical optimization of the customer relationship, with the main objective to maximize potential sales. On the transdisciplinary approach, engines and recommender systems brings together contributions linking information science and communications, marketing, sociology, mathematics and computing. It deals with the understan

  5. Material Systems

    DEFF Research Database (Denmark)

    Jensen, Mads Brath; Mortensen, Henrik Rubæk; Mullins, Michael

    2009-01-01

    This paper describes and reflects upon the results of an investigative project which explores the setting up of a material system - a parametric and generative assembly consisting of and taking into consideration material properties, manufacturing constraints and geometric behavior. The project...... approaches the subject through the construction of a logic-driven system aiming to explore the possibilities of a material system that fulfills spatial, structural and performative requirements concurrently and how these are negotiated in situations where they might be conflicting....

  6. Systems Engineering

    OpenAIRE

    Vaughan, William W.

    2016-01-01

    The term “systems engineering” when entered into the Google search page, produces a significant number of results, evidence that systems engineering is recognized as being important for the success of essentially all products. Since most readers of this item will be rather well versed in documents concerning systems engineering, I have elected to share some of the points made on this subject in a document developed by the European Cooperation for Space Standardization (ECSS), a component of t...

  7. Energetic Systems

    Data.gov (United States)

    Federal Laboratory Consortium — The Energetic Systems Division provides full-spectrum energetic engineering services (project management, design, analysis, production support, in-service support,...

  8. Intelligent systems

    CERN Document Server

    Irwin, J David

    2011-01-01

    Technology has now progressed to the point that intelligent systems are replacing humans in the decision making processes as well as aiding in the solution of very complex problems. In many cases intelligent systems are already outperforming human activities. Artificial neural networks are not only capable of learning how to classify patterns, such images or sequence of events, but they can also effectively model complex nonlinear systems. Their ability to classify sequences of events is probably more popular in industrial applications where there is an inherent need to model nonlinear system

  9. Systemic darwinism.

    Science.gov (United States)

    Winther, Rasmus Grønfeldt

    2008-08-19

    Darwin's 19th century evolutionary theory of descent with modification through natural selection opened up a multidimensional and integrative conceptual space for biology. We explore three dimensions of this space: explanatory pattern, levels of selection, and degree of difference among units of the same type. Each dimension is defined by a respective pair of poles: law and narrative explanation, organismic and hierarchical selection, and variational and essentialist thinking. As a consequence of conceptual debates in the 20th century biological sciences, the poles of each pair came to be seen as mutually exclusive opposites. A significant amount of 21st century research focuses on systems (e.g., genomic, cellular, organismic, and ecological/global). Systemic Darwinism is emerging in this context. It follows a "compositional paradigm" according to which complex systems and their hierarchical networks of parts are the focus of biological investigation. Through the investigation of systems, Systemic Darwinism promises to reintegrate each dimension of Darwin's original logical space. Moreover, this ideally and potentially unified theory of biological ontology coordinates and integrates a plurality of mathematical biological theories (e.g., self-organization/structure, cladistics/history, and evolutionary genetics/function). Integrative Systemic Darwinism requires communal articulation from a plurality of perspectives. Although it is more general than these, it draws on previous advances in Systems Theory, Systems Biology, and Hierarchy Theory. Systemic Darwinism would greatly further bioengineering research and would provide a significantly deeper and more critical understanding of biological reality.

  10. Caste System

    OpenAIRE

    Hoff, Karla

    2016-01-01

    In standard economics, individuals are rational actors and economic forces undermine institutions that impose large inefficiencies. The persistence of the caste system is evidence of the need for psychologically more realistic models of decision-making in economics. The caste system divides South Asian society into hereditary groups whose lowest ranks are represented as innately polluted. ...

  11. Recommender systems

    OpenAIRE

    Lu L.; Medo M.; Yeung C.H.; Zhang Y.-C.; Zhang Z.-K.; Zhou T.

    2012-01-01

    The ongoing rapid expansion of the Internet greatly increases the necessity of effective recommender systems for filtering the abundant information. Extensive research for recommender systems is conducted by a broad range of communities including social and computer scientists, physicists, and interdisciplinary researchers. Despite substantial theoretical and practical achievements, unification and comparison of different approaches are lacking, which impedes further advances. In this article...

  12. GEOMASS system

    International Nuclear Information System (INIS)

    Ohyama, Takuya; Saegusa, Hiromitsu

    2009-03-01

    As a part of the research and development regarding characterisation of deep geological environment, the GEOMASS (GEOLOGICAL MODELLING ANALYSIS AND SIMULATION SOFTWARE) system has been developed by the Japan Atomic Energy Agency in order to carry out geological and hydrogeological modelling and groundwater flow simulation and so on. The GEOMASS system integrates a commercial geological interpretation system (EarthVision), which is used for geological modelling and visualisation, with a proprietary code for groundwater flow (FracAffinity). This integrated system allows users to make rapid improvement of models as data increases. Also, it is possible to perform more realistic groundwater flow simulation due to the capability of modelling the rock mass as a continuum with discrete hydro-structural features in the rock mass. This paper consists of 'Overview of GEOMASS system', FracAffinity Theoretical Background' and 'FracAffinity User Guide' and is edited as a GEOMASS system manual. 'Overview of GEOMASS system' describes the outline of this system. 'FracAffinity Theoretical Background' describes the information of technical background of FracAffinity software. FracAffinity User Guide' describes the structure of the FracAffinity input files, the usage of FracAffinity Interface and flow-solver. Updating of the FracAffinity has been continued as needed and FracAffinity version3.3 is the latest version at present (July 2008). (author)

  13. Systems integration (automation system). System integration (automation system)

    Energy Technology Data Exchange (ETDEWEB)

    Fujii, K; Komori, T; Fukuma, Y; Oikawa, M [Nippon Steal Corp., Tokyo (Japan)

    1991-09-26

    This paper introduces business activities on an automation systems integration (SI) started by a company in July,1988, and describes the SI concepts. The business activities include, with the CIM (unified production carried out on computers) and AMENITY (living environment) as the mainstays, a single responsibility construction ranging from consultation on structuring optimal systems for processing and assembling industries and intelligent buildings to system design, installation and after-sales services. With an SI standing on users {prime} position taken most importantly, the business starts from a planning and consultation under close coordination. On the conceptual basis of structuring optimal systems using the ompany {prime}s affluent know-hows and tools and adapting and applying with multi-vendors, open networks, centralized and distributed systems, the business is promoted with the accumulated technologies capable of realizing artificial intelligence and neural networks in its background, and supported with highly valuable business results in the past. 10 figs., 1 tab.

  14. Creative Systems

    DEFF Research Database (Denmark)

    Manelius, Anne-Mette; Beim, Anne

    2007-01-01

    Opsamling af diskussioner på konferencen og udstillingen Creative Systems i september/oktober 2007. Konferencen og Udstillingen Creative Systems sætter fokus på systemer som en positiv drivkraft i den kreative skabelsesproces. CINARK inviterede fire internationale kapaciteter, som indenfor hver...... deres felt har beskæftiget sig med udviklingen af systemer. Kieran Timberlake, markant amerikansk tegnestue; Mark West, Professor på University of Manitoba, Canada, og pioner indenfor anvendelse af tekstilforskalling til betonstøbninger; Matilda McQuaid, Arkitekturhistoriker og kurator på udstillingen...... om Extreme Textiles på amerikanske Cooper Hewit Design Museum, samt Professor Ludger Hovestadt, ved ETH, Zürich der fokuserer på udvikling og anvendelse af logaritmiske systemtilgange. Udstillingen diskuterede ud fra deres meget forskellige arbejder, det kreative potentiale i anvendelsen af systemer...

  15. Reactive Systems

    DEFF Research Database (Denmark)

    Aceto, Luca; Ingolfsdottir, Anna; Larsen, Kim Guldstrand

    A reactive system comprises networks of computing components, achieving their goals through interaction among themselves and their environment. Thus even relatively small systems may exhibit unexpectedly complex behaviours. As moreover reactive systems are often used in safety critical systems......, the need for mathematically based formal methodology is increasingly important. There are many books that look at particular methodologies for such systems. This book offers a more balanced introduction for graduate students and describes the various approaches, their strengths and weaknesses, and when...... they are best used. Milner's CCS and its operational semantics are introduced, together with the notions of behavioural equivalences based on bisimulation techniques and with recursive extensions of Hennessy-Milner logic. In the second part of the book, the presented theories are extended to take timing issues...

  16. Upgraded RECOVER system - CASDAC system

    International Nuclear Information System (INIS)

    Yamamoto, Yoichi; Koyama, Kinji

    1992-03-01

    The CASDAC (Containment And Surveillance Data Authenticated Communication) system has been developed by JAERI for nuclear safeguards and physical protection of nuclear material. This system was designed and constructed as an upgraded RECOVER system, design concept of which was based on the original RECOVER system and also the TRANSEAVER system. Both of them were developed several years ago as a remote monitoring system for continual verification of security and safeguards status of nuclear material. The system consists of two subsystems, one of them is a Grand Command Center (GCC) subsystem and the other is a facility subsystem. Communication between the two subsystems is controlled through the international telephone line network. Therefore all communication data are encrypted to prevent access by an unauthorized person who may intend to make a falsification, or tapping. The facility subsystem has an appropriate measure that ensure data security and reliable operation under unattended mode of operator. The software of this system is designed so as to be easily used in other different types of computers. This report describes the outline of the CASDAC system and the results of its performance test. This work has been carried out in the framework of Japan Support Programme for Agency Safeguards (JASPAS) as a project, JA-1. (author)

  17. Watchdog System

    DEFF Research Database (Denmark)

    Madsen, Tanja Kidholm Osmann; Bahnsen, Chris Holmberg; Jensen, Morten Bornø

    This deliverable is part of WP4. Overall WP4 is motivated by the need for automatic systems that can ease the task of annotating massive amounts of traffic data. Concretely this deliverable is related to WP4.2 - the watchdog system. The idea with the watchdog is to develop a system that can remov...... huge chunks of video data where no events/interactions of interest are occurring and hence let a user focus on manually annotation of only the interesting stuff....

  18. Dynamical systems

    CERN Document Server

    Sternberg, Shlomo

    2010-01-01

    Celebrated mathematician Shlomo Sternberg, a pioneer in the field of dynamical systems, created this modern one-semester introduction to the subject for his classes at Harvard University. Its wide-ranging treatment covers one-dimensional dynamics, differential equations, random walks, iterated function systems, symbolic dynamics, and Markov chains. Supplementary materials offer a variety of online components, including PowerPoint lecture slides for professors and MATLAB exercises.""Even though there are many dynamical systems books on the market, this book is bound to become a classic. The the

  19. Water systems

    International Nuclear Information System (INIS)

    Riess, R.

    1980-01-01

    The present paper describes the coolant chemistry and its consequences for 1300 MWsub(e) KWU PWR plants. Some selected systems, i.e. primary heat transport system, steam water cycle and cooling water arrangements, are chosen for this description. Various aspects of coolant chemistry regarding general corrosion, selective types of corrosion and deposits on heat transfer surfaces have been discussed. The water supply systems necessary to fulfill the requirements of the coolant chemistry are discussed as well. It has been concluded that a good operating performance can only be achieved when - beside other factors - the water chemistry has been given sufficient consideration. (orig./RW)

  20. Water systems

    International Nuclear Information System (INIS)

    Riess, R.

    1981-01-01

    The present paper describes the coolant chemistry and its consequences for 1300 MWsub(e) KWU PWR plants. Some selected systems, i.e. primary heat transport system, steam water cycle and cooling water arrangements, are chosen for this description. Various aspects of coolant chemistry regarding general corrosion, selective types of corrosion and deposits on heat transfer surface have been discussed. The water supply systems necessary to fulfill the requirements of the coolant chemistry are discussed as well. It has been concluded that a good operating performance can only be achieved when - beside other factors - the water chemistry has been given sufficient consideration. (orig./RW)

  1. Imaging system

    International Nuclear Information System (INIS)

    Froggatt, R.J.

    1981-01-01

    The invention provides a two dimensional imaging system in which a pattern of radiation falling on the system is detected to give electrical signals for each of a plurality of strips across the pattern. The detection is repeated for different orientations of the strips and the whole processed by compensated back projection. For a shadow x-ray system a plurality of strip x-ray detectors are rotated on a turntable. For lower frequencies the pattern may be rotated with a Dove prism and the strips condensed to suit smaller detectors with a cylindrical lens. (author)

  2. Kaonic systems

    Directory of Open Access Journals (Sweden)

    Oset E.

    2012-12-01

    Full Text Available I make a short review of the situation of the kaonic systems, with novel information supporting the two Λ(1405 states from the K-d → nπΣ reaction. A review is made of the K¯$ar K$NN system with recent calculations converging to smaller bindings and larger widths. Novel systems involving two kaons and one nucleon or three kaons are also reported and finally a short discussion is made of the analogous state DNN for which recent studies find a large binding and a small width.

  3. The systems integration modeling system

    International Nuclear Information System (INIS)

    Danker, W.J.; Williams, J.R.

    1990-01-01

    This paper discusses the systems integration modeling system (SIMS), an analysis tool for the detailed evaluation of the structure and related performance of the Federal Waste Management System (FWMS) and its interface with waste generators. It's use for evaluations in support of system-level decisions as to FWMS configurations, the allocation, sizing, balancing and integration of functions among elements, and the establishment of system-preferred waste selection and sequencing methods and other operating strategies is presented. SIMS includes major analysis submodels which quantify the detailed characteristics of individual waste items, loaded casks and waste packages, simulate the detailed logistics of handling and processing discrete waste items and packages, and perform detailed cost evaluations

  4. ring system

    African Journals Online (AJOL)

    1,3,2-DIAZABORACYCLOALKANE. RING SYSTEM. Negussie Retta" and Robert H. Neilson. 'Department of Chemistry, Addis Ababa University, P.O. Box 1176, Addis Ababa, Ethiopia. Department of Chemistry, Texas Christian University.

  5. Septic Systems

    Science.gov (United States)

    The web site provides guidance and technical assistance for homeowners, government officials, industry professionals, and EPA partners about how to properly develop and manage individual onsite and community cluster systems that treat domestic wastewater.

  6. Respiratory system

    Science.gov (United States)

    Bartlett, R. G., Jr.

    1973-01-01

    The general anatomy and function of the human respiratory system is summarized. Breathing movements, control of breathing, lung volumes and capacities, mechanical relations, and factors relevant to respiratory support and equipment design are discussed.

  7. Bubble systems

    CERN Document Server

    Avdeev, Alexander A

    2016-01-01

    This monograph presents a systematic analysis of bubble system mathematics, using the mechanics of two-phase systems in non-equilibrium as the scope of analysis. The author introduces the thermodynamic foundations of bubble systems, ranging from the fundamental starting points to current research challenges. This book addresses a range of topics, including description methods of multi-phase systems, boundary and initial conditions as well as coupling requirements at the phase boundary. Moreover, it presents a detailed study of the basic problems of bubble dynamics in a liquid mass: growth (dynamically and thermally controlled), collapse, bubble pulsations, bubble rise and breakup. Special emphasis is placed on bubble dynamics in turbulent flows. The analysis results are used to write integral equations governing the rate of vapor generation (condensation) in non-equilibrium flows, thus creating a basis for solving a number of practical problems. This book is the first to present a comprehensive theory of boil...

  8. Systems Biology

    Indian Academy of Sciences (India)

    IAS Admin

    study and understand the function of biological systems, particu- larly, the response of such .... understand the organisation and behaviour of prokaryotic sys- tems. ... relationship of the structure of a target molecule to its ability to bind a certain ...

  9. Bricks / Systems

    DEFF Research Database (Denmark)

    At first glance, this book may appear eclectic. It contains writings from architectural practice in a language and structure based on subjective views and experiences, combined with research contributions based on systematic design investigations of discrete computational systems. Discussions range......, and it aims to illustrate and identify new modes of working in architecture, particularly with regards to brickwork and other complex systems of modular assemblies, whether physical or digital....

  10. Expert Systems

    OpenAIRE

    Lucas, P.J.F.

    2005-01-01

    Expert systems mimic the problem-solving activity of human experts in specialized domains by capturing and representing expert knowledge. Expert systems include a knowledge base, an inference engine that derives conclusions from the knowledge, and a user interface. Knowledge may be stored as if-then rules, orusing other formalisms such as frames and predicate logic. Uncertain knowledge may be represented using certainty factors, Bayesian networks, Dempster-Shafer belief functions, or fuzzy se...

  11. Nanorobotic Systems

    Directory of Open Access Journals (Sweden)

    Lixin Dong

    2008-11-01

    Full Text Available Two strategies towards the realization of nanotechnology have been presented, i.e., top-down and bottom up. The former one is mainly based on nanofabrication and includes technologies such as nano-lithography, nano-imprint, and etching. Presently, they are still 2D fabrication processes with low resolution. The later one is an assembly-based technique. At present, it includes such items as self-assembly, dip-pen lithography, and directed self-assembly. These techniques can generate regular nano patterns in large scales. To fabricate 3D complex nano devices there are still no effective ways by so far. Here we show our effort on the development of a nano laboratory, a prototype nanomanufacturing system, based on nanorobotic manipulations. In which, we take a hybrid strategy as shown in Fig. 1. In this system, nano fabrication and nano assembly can be performed in an arbitrary order to construct nano building blocks and finally nano devices. The most important feature in this system is that the products can be fed back into the system to shrink the system part by part leading to nanorobots. Property characterization can be performed in each intermediate process. Due to the nanorobotic manipulation system, dynamic measurement can be performed rather than conventional static observations.

  12. Fiscal system analysis - contractual systems

    International Nuclear Information System (INIS)

    Kaiser, M.J.

    2006-01-01

    Production sharing contracts are one of the most popular forms of contractual system used in petroleum agreements around the world, but the manner in which the fiscal terms and contract parameters impact system measures is complicated and not well understood. The purpose of this paper is to quantify the influence of private and market uncertainty in contractual fiscal systems. A meta-modelling approach is employed that couples the results of a simulation model with regression analysis to construct numerical functionals that quantify the fiscal regime. Relationships are derived that specify how the present value, rate of return, and take statistics vary as a function of the system parameters. The deepwater Girassol field development in Angola is taken as a case study. (author)

  13. Reactor system

    International Nuclear Information System (INIS)

    Miyano, Hiroshi; Narabayashi, Naoshi.

    1990-01-01

    The represent invention concerns a reactor system with improved water injection means to a pressure vessel of a BWR type reactor. A steam pump is connected to a heat removing system pipeline, a high pressure water injection system pipeline and a low pressure water injection system pipeline for injecting water into the pressure vessel. A pump actuation pipeline is disposed being branched from a main steam pump or a steam relieaf pipeline system, through which steams are supplied to actuate the steam pump and supply cooling water into the pressure vessel thereby cooling the reactor core. The steam pump converts the heat energy into the kinetic energy and elevates the pressure of water to a level higher than the pressure of the steams supplied by way of a pressure-elevating diffuser. Cooling water can be supplied to the pressure vessel by the pressure elevation. This can surely inject cooling water into the pressure vessel upon loss of coolant accident or in a case if reactor scram is necessary, without using an additional power source. (I.N.)

  14. ARAC system

    International Nuclear Information System (INIS)

    Kelly, M.F.; Wyman, R.H.

    1975-01-01

    In spite of the remarkable safety record of the nuclear industry as a whole, recent public concern over the potential impact of the industry's accelerated growth has prompted ERDA to expand its emergency response procedures. The Atmospheric Release Advisory Capability, ARAC, is a computer communications system designed to enhance the existing emergency response capability of ERDA nuclear facilities. ARAC will add at least two new functions to this capability: centralized, real-time data acquisition and storage, and simulation of the long range atmospheric transport of hazardous materials. To perform these functions, ARAC employs four major sub-systems or facilities: the site facility, the central facility, the global weather center and the regional model. The system has been under development for the past two years at the Lawrence Livermore Laboratory of the University of California

  15. Microbiology System

    Science.gov (United States)

    1992-01-01

    Technology originating in a NASA-sponsored study of the measurement of microbial growth in zero gravity led to the development of Biomerieux Vitek, Inc.'s VITEK system. VITEK provides a physician with accurate diagnostic information and identifies the most effective medication. Test cards are employed to identify organisms and determine susceptibility to antibiotics. A photo-optical scanner scans the card and monitors changes in the growth of cells contained within the card. There are two configurations - VITEK and VITEK JR as well as VIDAS, a companion system that detects bacteria, viruses, etc. from patient specimens. The company was originally created by McDonnell Douglas, the NASA contractor.

  16. Spin systems

    CERN Document Server

    Caspers, W J

    1989-01-01

    This book is about spin systems as models for magnetic materials, especially antiferromagnetic lattices. Spin-systems are well-defined models, for which, in special cases, exact properties may be derived. These special cases are for the greater part, one- dimensional and restricted in their applicability, but they may give insight into general properties that also exist in higher dimension. This work pays special attention to qualitative differences between spin lattices of different dimensions. It also replaces the traditional picture of an (ordered) antiferromagnetic state of a Heisenberg sy

  17. Distributed systems

    CERN Document Server

    Van Steen, Maarten

    2017-01-01

    For this third edition of "Distributed Systems," the material has been thoroughly revised and extended, integrating principles and paradigms into nine chapters: 1. Introduction 2. Architectures 3. Processes 4. Communication 5. Naming 6. Coordination 7. Replication 8. Fault tolerance 9. Security A separation has been made between basic material and more specific subjects. The latter have been organized into boxed sections, which may be skipped on first reading. To assist in understanding the more algorithmic parts, example programs in Python have been included. The examples in the book leave out many details for readability, but the complete code is available through the book's Website, hosted at www.distributed-systems.net.

  18. Immune System

    Science.gov (United States)

    ... of the Immune System Print en español El sistema inmunitario Whether you're stomping through the showers ... of Use Notice of Nondiscrimination Visit the Nemours Web site. Note: All information on TeensHealth® is for ...

  19. Operating Systems

    Indian Academy of Sciences (India)

    areas in which this type is useful are multimedia, virtual reality, and advanced scientific projects such as undersea exploration and planetary rovers. Because of the expanded uses for soft real-time functionality, it is finding its way into most current operating systems, including major versions of Unix and Windows NT OS.

  20. Barrier Systems

    NARCIS (Netherlands)

    Heteren, S. van

    2015-01-01

    Barrier-system dynamics are a function of antecedent topography and substrate lithology, Relative sea-level (RSL) changes, sediment availability and type, climate, vegetation type and cover, and various aero- and hydrodynamic processes during fair-weather conditions and extreme events. Global change

  1. Systems Science

    Science.gov (United States)

    Christakis, Alexander; Hammond, Debora; Jackson, Michael; Laszlo, Alexander; Mitroff, Ian; Snowden, Dave; Troncale, Len; Carr-Chellman, Alison; Spector, J. Michael; Wilson, Brent

    2013-01-01

    Scholars representing the field of systems science were asked to identify what they considered to be the most exciting and imaginative work currently being done in their field, as well as how that work might change our understanding. The scholars included Alexander Christakis, Debora Hammond, Michael Jackson, Alexander Laszlo, Ian Mitroff, Dave…

  2. Transport system

    NARCIS (Netherlands)

    Drenth, K.F.

    1999-01-01

    The transport system comprises at least one road surface (2) and at least one vehicle (4) on wheels (6). The road surface (2) has a substantially bowl-shaped cross section and the vehicle (4) is designed so that the wheels (6) run directly on the road surface (2) while the road surface (2) acts as a

  3. Quorum Systems

    DEFF Research Database (Denmark)

    Wattenhofer, Roger; Förster, Klaus-Tycho

    2016-01-01

    What happens if a single server is no longer powerful enough to service all your customers? The obvious choice is to add more servers and to use the majority approach (e.g. Paxos, Chapter 2) to guarantee consistency. However, even if you buy one million servers, a client still has to access more ...... study the theory behind overlapping sets, known as quorum systems....

  4. System Dynamics

    Science.gov (United States)

    Morecroft, John

    System dynamics is an approach for thinking about and simulating situations and organisations of all kinds and sizes by visualising how the elements fit together, interact and change over time. This chapter, written by John Morecroft, describes modern system dynamics which retains the fundamentals developed in the 1950s by Jay W. Forrester of the MIT Sloan School of Management. It looks at feedback loops and time delays that affect system behaviour in a non-linear way, and illustrates how dynamic behaviour depends upon feedback loop structures. It also recognises improvements as part of the ongoing process of managing a situation in order to achieve goals. Significantly it recognises the importance of context, and practitioner skills. Feedback systems thinking views problems and solutions as being intertwined. The main concepts and tools: feedback structure and behaviour, causal loop diagrams, dynamics, are practically illustrated in a wide variety of contexts from a hot water shower through to a symphony orchestra and the practical application of the approach is described through several real examples of its use for strategic planning and evaluation.

  5. System Description:

    DEFF Research Database (Denmark)

    Schürmann, Carsten; Poswolsky, Adam

    2009-01-01

    Delphin is a functional programming language [Adam Poswolsky and Carsten Schürmann. Practical programming with higher-order encodings and dependent types. In European Symposium on Programming (ESOP), 2008] utilizing dependent higher-order datatypes. Delphin's two-level type-system cleanly separates...

  6. Immune System

    Science.gov (United States)

    A properly functioning immune system is essential to good health. It defends the body against infectious agents and in some cases tumor cells. Individuals with immune deficiencies resulting from genetic defects, diseases (e.g., AIDS, leukemia), or drug therapies are more suscepti...

  7. Bioenergy systems

    International Nuclear Information System (INIS)

    Mitchell, C.P.

    1997-01-01

    The objective of this paper is to demonstrate that a bioenergy system has to be considered as an integrated process in which each stage or step interacts with other steps in the overall process. There are a number of stages in the supply and conversion of woody biomass for energy. Each step in the chain has implications for the next step and for overall system efficiency. The resource can take many forms and will have varying physical and chemical characteristics which will influence the efficiency and cost of conversion. The point in the supply chain at which size and moisture content is reduced and the manner in which it is done is influential in determining feedstock delivered cost and overall system costs. To illustrate the interactions within the overall system, the influence of the nature, size and moisture content of delivered feedstocks on costs of generating electricity via thermal conversion processes is examined using a model developed to investigate the inter-relationships between the stages in the supply chain. (author)

  8. Urogenital system

    International Nuclear Information System (INIS)

    Hamm, B.; Asbach, P.; Beyersdorff, D.; Hein, P.; Zaspel, U.

    2007-01-01

    The book is focussed on the radiological diagnostics of diseases in the urogential system. The description of the specific diseases, the identification by modern imaging techniques, the interpretation of examinatory results and therapeutic options are systematically treated in 4 chapters: kidney and adrenal glands, urinary tract, male genitals, female genitals

  9. Mirror systems.

    Science.gov (United States)

    Fogassi, Leonardo; Ferrari, Pier Francesco

    2011-01-01

    Mirror neurons are a class of visuomotor neurons, discovered in the monkey premotor cortex and in an anatomically connected area of the inferior parietal lobule, that activate both during action execution and action observation. They constitute a circuit dedicated to match actions made by others with the internal motor representations of the observer. It has been proposed that this matching system enables individuals to understand others' behavior and motor intentions. Here we will describe the main features of mirror neurons in monkeys. Then we will present evidence of the presence of a mirror system in humans and of its involvement in several social-cognitive functions, such as imitation, intention, and emotion understanding. This system may have several implications at a cognitive level and could be linked to specific social deficits in humans such as autism. Recent investigations addressed the issue of the plasticity of the mirror neuron system in both monkeys and humans, suggesting also their possible use in rehabilitation. WIREs Cogn Sci 2011 2 22-38 DOI: 10.1002/wcs.89 For further resources related to this article, please visit the WIREs website. Copyright © 2010 John Wiley & Sons, Ltd.

  10. Systemic Planning

    DEFF Research Database (Denmark)

    Leleur, Steen

    This book presents principles and methodology for planning in a complex world. It sets out a so-called systemic approach to planning, among other things, by applying “hard” and “soft” methodologies and methods in combination. The book is written for Ph.D and graduate students in engineering...

  11. Energy systems

    International Nuclear Information System (INIS)

    Haefele, W.

    1974-01-01

    Up to the present the production, transmission and distribution of energy has been considered mostly as a fragmented problem; at best only subsystems have been considered. Today the scale of energy utilization is increasing rapidly, and correspondingly, the reliance of societies on energy. Such strong quantitative increases influence the qualitative nature of energy utilization in most of its aspects. Resources, reserves, reliability and environment are among the key words that may characterize the change in the nature of the energy utilization problem. Energy can no longer be considered an isolated technical and economical problem, rather it is embedded in the ecosphere and the society-technology complex. Restraints and boundary conditions have to be taken into account with the same degree of attention as in traditional technical problems, for example a steam turbine. This results in a strong degree of interweaving. Further, the purpose of providing energy becomes more visible, that is, to make survival possible in a civilized and highly populated world on a finite globe. Because of such interweaving and finiteness it is felt that energy should be considered as a system and therefore the term 'energy systems' is used. The production of energy is only one component of such a system; the handling of energy and the embedding of energy into the global and social complex in terms of ecology, economy, risks and resources are of similar importance. he systems approach to the energy problem needs more explanation. This paper is meant to give an outline of the underlying problems and it is hoped that by so doing the wide range of sometimes confusing voices about energy can be better understood. Such confusion starts already with the term 'energy crisis'. Is there an energy crisis or not? Much future work is required to tackle the problems of energy systems. This paper can only marginally help in that respect. But it is hoped that it will help understand the scope of the

  12. Energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Haefele, W [Nuclear Research Centre, Applied Systems Analysis and Reactor Physics, Karlsruhe (Germany); International Institute for Applied Systems Analysis, Laxenburg (Austria)

    1974-07-01

    Up to the present the production, transmission and distribution of energy has been considered mostly as a fragmented problem; at best only subsystems have been considered. Today the scale of energy utilization is increasing rapidly, and correspondingly, the reliance of societies on energy. Such strong quantitative increases influence the qualitative nature of energy utilization in most of its aspects. Resources, reserves, reliability and environment are among the key words that may characterize the change in the nature of the energy utilization problem. Energy can no longer be considered an isolated technical and economical problem, rather it is embedded in the ecosphere and the society-technology complex. Restraints and boundary conditions have to be taken into account with the same degree of attention as in traditional technical problems, for example a steam turbine. This results in a strong degree of interweaving. Further, the purpose of providing energy becomes more visible, that is, to make survival possible in a civilized and highly populated world on a finite globe. Because of such interweaving and finiteness it is felt that energy should be considered as a system and therefore the term 'energy systems' is used. The production of energy is only one component of such a system; the handling of energy and the embedding of energy into the global and social complex in terms of ecology, economy, risks and resources are of similar importance. he systems approach to the energy problem needs more explanation. This paper is meant to give an outline of the underlying problems and it is hoped that by so doing the wide range of sometimes confusing voices about energy can be better understood. Such confusion starts already with the term 'energy crisis'. Is there an energy crisis or not? Much future work is required to tackle the problems of energy systems. This paper can only marginally help in that respect. But it is hoped that it will help understand the scope of the

  13. TUBO system

    International Nuclear Information System (INIS)

    Barbosa, H.J.C.; Guerreiro, J.N.C.; Toledo, E.M.

    1980-01-01

    Proceedings recently incorporated to TUBO system like the seismic analysis and the stress verification acccording to ASME-Boiler Rule and Pressure Vessel Code-section III are presented. The seismic analysis comprehend the consideration of uniform motion of the support, its multiple excitation, and the attainment of the spectral response for both cases. The module for stress verification uses stresses resulting fromthe combination of the loads specified by the user, in the automatic verification of permissible stresses for the pipings class 1 and 2, based on criteria NB-3650 and NC-3650 of ASME. The implementation of these proceedings in the TUBO system are discussed and a numerical example that covers the different phases of a stress analysis in a piping is presented [pt

  14. Solar Systems

    Science.gov (United States)

    1979-01-01

    The solar collectors shown are elements of domestic solar hot water systems produced by Solar One Ltd., Virginia Beach, Virginia. Design of these systems benefited from technical expertise provided Solar One by NASA's Langley Research Center. The company obtained a NASA technical support package describing the d e sign and operation of solar heating equipment in NASA's Tech House, a demonstration project in which aerospace and commercial building technology are combined in an energy- efficient home. Solar One received further assistance through personal contact with Langley solar experts. The company reports that the technical information provided by NASA influenced Solar One's panel design, its selection of a long-life panel coating which increases solar collection efficiency, and the method adopted for protecting solar collectors from freezing conditions.

  15. Bilateral system. The ABACC system

    International Nuclear Information System (INIS)

    Nicolas, Ruben O.

    2001-01-01

    After relating the antecedents of the creation of the Brazilian-Argentine Agency for the Accounting and Control of Nuclear Materials (ABACC), the paper describes the common system of accounting and control set up by Argentina and Brazil. The organization of ABACC is also outlined

  16. Physical system requirements: Overall system

    International Nuclear Information System (INIS)

    1992-01-01

    The Nuclear Waste Policy Act (NWPA) of 1982 assigned to the Department of Energy (DOE) the responsibility for managing the disposal of spent nuclear fuel and high-level radioactive waste and established the Office of Civilian Radioactive Waste Management (OCRWM) for that purpose. The Secretary of Energy, in his November 1989 report to Congress (DOE/RW-0247), announced three new initiatives for conduct of the Civilian Radioactive Waste Management (CRWM) program. One of these initiatives was to establish improved management structure and procedures. In response, OCRWM performed a management study and the Direct subsequently issued the Management Systems Improvement Strategy (MSIS) on August 10, 1990, calling for a rigorous implementation of systems engineering principles with a special emphasis on functional analysis. This approach establishes a framework for integrating the program management efforts with the technical requirements analysis into a single, unified, and consistent program. The functional analysis approach recognizes that just the facilities and equipment comprising the physical waste management system must perform certain functions, so must certain programmatic and management functions be performed within the program in order to successfully bring the physical system into being

  17. Security system

    Science.gov (United States)

    Baumann, Mark J.; Kuca, Michal; Aragon, Mona L.

    2016-02-02

    A security system includes a structure having a structural surface. The structure is sized to contain an asset therein and configured to provide a forceful breaching delay. The structure has an opening formed therein to permit predetermined access to the asset contained within the structure. The structure includes intrusion detection features within or associated with the structure that are activated in response to at least a partial breach of the structure.

  18. Cardiovascular system

    International Nuclear Information System (INIS)

    Soulen, R.L.; Grosh, J.

    1984-01-01

    Invasive cardiovascular diagnostic procedures involve a finite risk and therefore can be recommended only when the benefit appears to exceed the risk by a substantial margin. The risk/benefit ratio varies not only with the procedure concerned but with the status of the vascular system, concomitant diseases, and the risks of both the suspected illness and its treatment. The risks inherent in the procedures per se are detailed in the sections to follow

  19. Priority Systems

    OpenAIRE

    Gössler , Gregor; Sifakis , Joseph

    2004-01-01

    Projet POP_ART; We present a framework for the incremental construction of deadlock-free systems meeting given safety properties. The framework borrows concepts and basic results from the controller synthesis paradigm by considering a step in the construction process as a controller synthesis problem. We show that priorities are expressive enough to represent restrictions induced by deadlock-free controllers preserving safety properties. We define a correspondence between such restrictions an...

  20. Imaging system

    International Nuclear Information System (INIS)

    Rushbrooke, J.G.; Ansorge, R.E.

    1987-01-01

    A moving object such as a container on a conveyor belt is imaged by an optical system onto a charge coupled device array in which the lines of the array are arranged perpendicular to the direction of motion of the object. The speed of movement of the object is sensed to generate electrical signals which are processed to provide shift signals enabling the shifting of data row to row in the array in synchronism with the movement of the container. The electrical charge associated with a given point on the array is transferred from one line to the other until it appears at the last line of the array, from which it is read out in known manner in conjunction with all other electrical charges associated with the row of charge coupled devices in the last line of the array. Due to the integrating effect achieved, the aperture of the imaging system can be much smaller than otherwise would be required, and/or the level of light illumination can be reduced. The imaging system can be applied to X-ray inspection devices, aerial surveillance or scanning of moving documents in copying processes. (author)

  1. Braking system

    Science.gov (United States)

    Norgren, D.U.

    1982-09-23

    A balanced braking system comprising a plurality of braking assemblies located about a member to be braked. Each of the braking assemblies consists of a spring biased piston of a first material fitted into a body of a different material which has a greater contraction upon cooling than the piston material. The piston is provided with a recessed head portion over which is positioned a diaphragm and forming a space therebetween to which is connected a pressurized fluid supply. The diaphragm is controlled by the fluid in the space to contact or withdraw from the member to be braked. A cooling means causes the body within which the piston is fitted to contract more than the piston, producing a tight shrink fit therebetween. The braking system is particularly applicable for selectively braking an arbor of an electron microscope which immobilizes, for example, a vertically adjustable low temperature specimen holder during observation. The system provides balanced braking forces which can be easily removed and re-established with minimal disturbance to arbor location.

  2. Protecting information in systems of systems

    NARCIS (Netherlands)

    Trivellato, D.

    2012-01-01

    Systems of systems are coalitions of autonomous and heterogeneous systems that collaborate to achieve a common goal. The component systems of a system of systems often belong to different security domains, which are governed by different authorities (hereafter called parties). Furthermore, systems

  3. Dynamical systems

    CERN Document Server

    Birkhoff, George D

    1927-01-01

    His research in dynamics constitutes the middle period of Birkhoff's scientific career, that of maturity and greatest power. -Yearbook of the American Philosophical Society The author's great book€¦is well known to all, and the diverse active modern developments in mathematics which have been inspired by this volume bear the most eloquent testimony to its quality and influence. -Zentralblatt MATH In 1927, G. D. Birkhoff wrote a remarkable treatise on the theory of dynamical systems that would inspire many later mathematicians to do great work. To a large extent, Birkhoff was writing about his o

  4. Nuclear systems

    CERN Document Server

    Todreas, Neil E

    2011-01-01

    Principal Characteristics of Power ReactorsIntroductionPower CyclesPrimary Coolant SystemsReactor CoresFuel AssembliesAdvanced Water- and Gas-Cooled Reactors (Generation III And III+)Advanced Thermal and Fast Neutron Spectrum Reactors (Generation IV)ReferencesProblemsThermal Design Principles and ApplicationIntroductionOverall Plant Characteristics Influenced by Thermal Hydraulic ConsiderationsEnergy Production and Transfer ParametersThermal Design LimitsThermal Design MarginFigures of Merit for Core Thermal PerformanceThe Inverted Fuel ArrayThe Equivalent Annulus ApproximationReferencesProble

  5. Videobasierte Systeme

    Science.gov (United States)

    Knoll, Peter

    Videosensoren spielen für Fahrerassistenz systeme eine zentrale Rolle, da sie die Interpretation visueller Informationen (Objektklassifikation) gezielt unterstützen. Im Heckbereich kann die Video sensorik in der einfachsten Variante die ultraschallbasierte Einparkhilfe bei Einpark- und Rangiervorgängen unterstützen. Beim Nachtsichtsystem NightVision wird das mit Infrarotlicht angestrahlte Umfeld vor dem Fahrzeug mit einer Frontkamera aufgenommen und im Fahrzeugcockpit auf einem Display dem Fahrer angezeigt (s. Nachtsichtsysteme). Andere Fahrerassistenzsysteme verarbeiten die Videosignale und generieren daraus gezielt Informationen, die für eigenständige Funktionen (z. B. Spurverlassenswarner) oder aber als Zusatzinformation für andere Funktionen ausgewertet werden (Sensordatenfusion).

  6. Relaxation System

    Science.gov (United States)

    1987-01-01

    Environ Corporation's relaxation system is built around a body lounge, a kind of super easy chair that incorporates sensory devices. Computer controlled enclosure provides filtered ionized air to create a feeling of invigoration, enhanced by mood changing aromas. Occupant is also surrounded by multidimensional audio and the lighting is programmed to change colors, patterns, and intensity periodically. These and other sensory stimulators are designed to provide an environment in which the learning process is stimulated, because research has proven that while an individual is in a deep state of relaxation, the mind is more receptive to new information.

  7. Bearing system

    Science.gov (United States)

    Kapich, Davorin D.

    1987-01-01

    A bearing system includes backup bearings for supporting a rotating shaft upon failure of primary bearings. In the preferred embodiment, the backup bearings are rolling element bearings having their rolling elements disposed out of contact with their associated respective inner races during normal functioning of the primary bearings. Displacement detection sensors are provided for detecting displacement of the shaft upon failure of the primary bearings. Upon detection of the failure of the primary bearings, the rolling elements and inner races of the backup bearings are brought into mutual contact by axial displacement of the shaft.

  8. Propulsion Systems

    Science.gov (United States)

    2011-03-31

    stand.    CV CS x dAvvdVov dt d F   (18-1) Where  denotes density and vx is the velocity in the x-direction. The first term on the...by  but to avoid confusion with  from Eqs. 18-7 to 10, it is denoted k in this formula . Ru is the universal gas constant (8.314472 J/mol K), pe is...Russian Federation Used on Phobos spacecraft as main engines 74 1.03 NTO/ UDMH 13.73-19.61 316-325 Orbital Maneuvering System 1 Aerojet Shuttle

  9. Expert Systems: What Is an Expert System?

    Science.gov (United States)

    Duval, Beverly K.; Main, Linda

    1994-01-01

    Describes expert systems and discusses their use in libraries. Highlights include parts of an expert system; expert system shells; an example of how to build an expert system; a bibliography of 34 sources of information on expert systems in libraries; and a list of 10 expert system shells used in libraries. (Contains five references.) (LRW)

  10. System analysis and design

    International Nuclear Information System (INIS)

    Son, Seung Hui

    2004-02-01

    This book deals with information technology and business process, information system architecture, methods of system development, plan on system development like problem analysis and feasibility analysis, cases for system development, comprehension of analysis of users demands, analysis of users demands using traditional analysis, users demands analysis using integrated information system architecture, system design using integrated information system architecture, system implementation, and system maintenance.

  11. Posting system

    International Nuclear Information System (INIS)

    Hackney, S.

    1983-01-01

    A system for posting hazardous materials into and out of an enclosure, such as a glovebox, through a port in a wall of the enclosure. The port is normally closed by a door which cooperates with a removable end closure, on a container or the like when the latter is presented to and secured at the port. The container is secured in position at the port by means of a rotatable coupling ring. A single interlock ensures that the door cannot be opened in the absence of a container at the port and also that the container cannot be removed from the port when the door is open. In place of the container, a glove secured to a rigid sleeve may be used to enable the operator to perform a work function within the glovebox. (author)

  12. hydrothermal systems

    Directory of Open Access Journals (Sweden)

    L. Bayón

    2002-01-01

    Full Text Available In this paper, we revise the classical formulation of the problem depriving it of the concepts that are superfluous from the mathematical point of view. We observe that a number of power stations can be substituted by a single one that behaves equivalently to the entire set. Proceeding in this way, we obtain a variational formulation in its purest sense (without restrictions. This formulation allows us to employ the theory of calculus of variations to the highest degree. We then calculate the equivalent minimizer in the case where the cost functions are second-order polynomials. We prove that the equivalent minimizer is a second-order polynomial with piece-wise constant coefficients. Moreover, it belongs to the class C1. Finally, we present various examples prompted by real systems and perform the proposed algorithms using Mathematica.

  13. Nonlinear systems

    CERN Document Server

    Palmero, Faustino; Lemos, M; Sánchez-Rey, Bernardo; Casado-Pascual, Jesús

    2018-01-01

    This book presents an overview of the most recent advances in nonlinear science. It provides a unified view of nonlinear properties in many different systems and highlights many  new developments. While volume 1 concentrates on mathematical theory and computational techniques and challenges, which are essential for the study of nonlinear science, this second volume deals with nonlinear excitations in several fields. These excitations can be localized and transport energy and matter in the form of breathers, solitons, kinks or quodons with very different characteristics, which are discussed in the book. They can also transport electric charge, in which case they are known as polarobreathers or solectrons. Nonlinear excitations can influence function and structure in biology, as for example, protein folding. In crystals and other condensed matter, they can modify transport properties, reaction kinetics and interact with defects. There are also engineering applications in electric lattices, Josephson junction a...

  14. Posting system

    International Nuclear Information System (INIS)

    Jones, E.L.

    1983-01-01

    A posting system for the movement of equipment, such as a manipulator, into and out of an enclosure e.g. a cell or glovebox, for toxic or radioactive materials has the manipulator arranged within a collapsible bellows-like container with an end of the container cooperating with a port entry to the enclosure. The collapsible container isolates the manipulator from the environment outside the enclosure and allows the manipulator to enter and leave the contaminated enclosure without breach of the containment. A particular construction of cell for use with radioactive material is described, having a thick wall of shielding material such as concrete provided with a door normally closed by a Pb shutter and having a cylindrical gamma shield block located over the shutter on the exterior of the wall. (author)

  15. Systems engineering simplified

    CERN Document Server

    Cloutier, Robert; Bone, Mary Alice

    2015-01-01

    IntroductionOverviewDiscussion of Common TerminologyThe Case for Systems EngineeringA Brief History of Systems EngineeringSystem ExamplesSummaryThe System Life CycleManaging System Development-The Vee ModelSystem ProductionSystem Utilization and SupportSystem Retirement and DisposalOther Systems Engineering Development ModelsSpiral ModelAgile Model for Systems EngineeringSystem of InterestAbstraction and DecompositionIntegrationDeveloping and Managing RequirementsCyclone Requiremen

  16. Fiscal 1999 report on basic research for promotion of joint implementation programs. Basic research on introduction of energy saving facilities into Bulgaria's Kremikovtzi Steelworks; 1999 nendo Bulgaria Kremikovtzi seitetsusho no sho energy setsubi donyu kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The plant undergoes a survey for higher energy efficiency, pursuant to the COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) protocol. Dry quenching and coal moisture control are investigated for the coke oven; exhaust heat recovery and high efficiency ignition burner for the sintering machine; top pressure recovery power generation and hot stove exhaust heat recovery for blast furnace; gas recovery for the converter; scrap preheating for the electric furnace; continuous casting and soaking pit efficiency improvement for the blooming process; hot charge and heating furnace efficiency improvement for the hot strip mill reheating furnace; and furnace efficiency improvement and hydrogen annealing applicability for the annealing furnace. The energy saving effects of the above are calculated under conditions that one more of the same be added to the continuous slab casting unit and that a continuous bloom casting unit be constructed for the continuous casting of the whole, and that hydrogen annealing be adopted. A reduction of 141,900toe/year is to be achieved, which occupies 6% of the energy consumption of the whole steelworks. A greenhouse gas reduction of 333,600t-CO2/year is feasible. Now that privatization is under way for business reconstruction and rationalization, suggestions will be presented in consideration of the order of priority of investment recovery effects with attention paid to the privation program. (NEDO)

  17. Survey report for fiscal 1999. Reference book for standard heat calculations in high-performance industrial furnace introduction field test project; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Hyojun netsu keisanshiki kijunsho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to verify in a short time the heat recovery capability being the evaluation parameter for the technologies to develop the high-performance industrial furnace, a standard calculation book will be prepared, which standardizes the data collection methods and heat calculation methods, and is used as the standard data sheets and bases. Evaluations and analyses will be given on business types, furnace constructions, thermal technologies, and functions in the research items adopted in the field test project. The results will be used to recognize the business entities engaged in the project in the next fiscal year, furnace types and sizes, establish the industrial furnace subjected to researches in the next fiscal year, and proliferate and expand the related business entities. Standard data sheets will be prepared on seven kinds of furnaces, heating furnaces (continuous and batch types), ladles, heat treatment furnaces (continuous and batch types), gas treatment furnaces, and melting furnaces. The standard data sheets will cover the following items: evaluation parameters (energy saving rate, thermal efficiency, and waste heat recovery rate), calculating conditions to be the base for the evaluation parameters, a heat production book to be the base for calculating the heat unit requirement, and a standard calculation book to be the base for the heat production table. The standard data sheets (including the standard calculation book) and floppy disks are submitted. (NEDO)

  18. Fiscal 2000 survey report. Refuse-fueled power generation introduction technology, etc. Part 2. Survey of general refuse-fueled power generation; 2000 nendo chosa hokokusho. Haikibutsu hatsuden donyu gijutsu chosa to - Ippan haikibutsu hatsuden chosa Part 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Surveys were conducted of the effect on waste quality of the Law for Promotion of Sorted Collection and Recycling of Containers and Packaging, diffusion of PFI (private finance initiative) involving refuse-fueled power generation, recycling of slag, etc. Questionnairing was conducted for the survey of the effect on waste of the effectuation of the recycling law, size of population supplying the waste and the amount actually incinerated, actually measured data of the composition of incinerated waste, assorted collection programs, amount reducing measures, and the like. Studies were made as to if the empirical formulas applied in the survey of the preceding fiscal year would remain applicable after the coming into force of the recycling law. In the survey of PFI popularization, it was found that the rate it was taken into account for concrete projects was so low as 13.8% though most of the autonomous bodies had cognizance of PFI. It was requested that it be clearly stipulated that 'the conventional subsidies and grants apply also to PFI projects.' In the survey of conversion of residue into molten slag in refuse-fueled power generation and its reuse, four kinds of slag specimens were examined for physical properties, elution, and analyzed for ingredients, and then it was found that they posed no problems like heavy metal elution. (NEDO)

  19. Fiscal 1999 geothermal energy development promotion survey. Report on survey of introduction of techniques for predicting impact on hot springs; 1999 nendo chinetsu kaihatsu sokushin chosa hokokusho. Onsen eikyo yosoku shuho donyu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-08-01

    In an effort to find guidelines on how to proceed with geothermal energy development so that it may coexist with hot springs, investigations are conducted into cases of impacts on hot springs imposed by geothermal energy development activities. An impact is judged to exist when geothermal development results in a decrease or depletion of pumped or spontaneously welling hot spring water, change in the concentration of dissolved chemical ingredients, fall in water temperature, or in an increase in the amount of discharged steam. Keyword-aided retrieval of data from databases is performed, and geothermal magazines are referred to for information. There are articles reporting impacts imposed by geothermal development on hot springs in the Palinpinon area (Philippines) and 12 others and in the Corwin Springs area (U.S.) and 13 others. These articles carrying outlines and impacts of geothermal development are collected, put in order, and analyzed. Cases in which such impacts are found to exist are categorized into four groups and, in each group, episodes are differentiated from each other by the type of mechanism linking the aquifer and the reservoir which is the object of development. (NEDO)

  20. Survey report for fiscal 1999. Evaluation and analysis on items applied for in high-performance industrial furnace introduction field test project in fiscal 1999; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Obo anken hyoka bunseki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes comprehensive evaluation and analysis mainly on the 51 items adopted in the high-performance industrial furnace introduction field tests. The development of a high-performance industrial furnace has completed the fundamental development research in fiscal 1998, and the possibility was verified on energy saving of more than 30% and reduction of NOx emission by 50% over that by conventional furnaces. Upon this fundamental achievement, the field test project has started as the comprehensive approach to developing the practically usable technologies for three years from fiscal 1998 until fiscal 2000, which is being promoted as a joint research project. According to the survey on the actual state in fiscal 1998, a little less than 20,000 industrial furnaces having combustion capacity of more than 500,000 Kcal/hr (excepting boilers) are being used. If these furnaces are converted into the high-performance industrial furnace, energy conservation of 210,000 x 10{sup 6} Mcal (converted to crude oil of 22.7 x 10{sup 6} kl/year) can be achieved from the maximum annual energy consumption of 700,000 x 10{sup 6} Mcal (converted to crude oil of 75.7 x 10{sup 6} kl/year). This conservation amount corresponds to about 12% of the final energy consumption in the whole Japanese industrial departments in fiscal 1996. It is expected that the performance of the full-size high-performance industrial furnace will be verified, and this technology will be promoted for wide proliferation. (NEDO)

  1. Fiscal 1998 research report. Current state survey for promoting the field test project for introduction of advanced industrial furnaces; 1998 nendo koseino kogyoro donyu field test jigyo ni okeru jigyo sokushin no tame no jittai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Survey was made on the current state of installation and operation of industrial furnaces mainly in manufacturers to predict the applicability of advanced industrial furnaces, and study was made on energy consumption trends, the energy saving effect of advanced industrial furnaces, and factor extraction for their applicability. In the survey, questionnaires were delivered to 4,597 offices extracted from domestic 50,780 offices with employees more than 30, and nearly 30% of them were recovered, covering nearly 2.6% of all the offices concerned with this survey. As the survey result, the total annual energy consumption of domestic manufacturers was estimated to be 740,949 x 10{sup 6}Mcal, and among it, 709,709 x 10{sup 6}Mcal for large industrial furnaces. Under the assumption that nearly 30% of large industrial furnaces in operation are replaced with advanced industrial furnaces, energy saving expectation is estimated to be 210,000 x 10{sup 6}Mcal. Opinions and demands for this project showed the difficulty in their application to industrial furnaces in operation and study on their effects. Further enlightenment activities are necessary. (NEDO)

  2. Report on FS survey for project of introduction of highly energy-efficient trolley buses into the Mexico Metropolitan Area in FY 1997; 1997 nendo chosa hokokusho (Mexico city eno sho energy gata trolley bus donyu project FS chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Traffic jam and air pollution by automobiles are currently getting severe in the Mexico Metropolitan Area. Trolley buses were introduced for improving the environment more than ten years ago. Vehicles become too old for use, and their energy efficiency is low. In this project, 200 highly energy-efficient trolley buses are introduced to replace old inefficient trolley buses, which results in the improved traffic convenience in the City and enhanced energy efficiency. The new energy-efficient trolley buses are made of energy-efficient control VVVF inverters produced and exported by MELCO (Mitsubishi Electric Corporation), energy-efficient motors by MELMEX (Mitsubishi Electric Corporation, Mexico), and bodies by MASA which is a major manufacturer of bus bodies. The objective of this research is to analyze the background of introduction of new energy-efficient trolley buses and the effects of the present project. The results of analysis are going to be utilized for future promotion of the Joint Implementation and Clean Development Mechanism. 30 refs., 30 figs., 24 tabs.

  3. FY 2000 report on the investigational study of the introduction/spread of clean energy vehicles for transportation business use; 2000 nendo chosa hokokusho. Unso jigyo yo clean energy jidosha no donyu fukyu ni kakawaru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A comparative study of the cost effectiveness in improvement of emission gas was made between the diesel particulate filter (DPF) which is studied as measures against toxic emission gas from the vehicles already sold and the compressed natural gas (CNG) vehicle which has a large number of spread among clean energy vehicles. In the trial calculation, 18 cases were set up using measures by year against diesel car emission gas, use period and annual running distance as valuables. As a result of the study, the following conclusions were obtained. At the present time, when the vehicle price dropped approximately 40% from that at the beginning of the introduction, the cost effectiveness of CNG vehicle is larger than that of diesel car with DPF. Since the unit price of natural gas is comparatively higher than that of light oil, the longer the annual running distance is, the smaller the cost effectiveness of CNG vehicle is than that of diesel car with DPF. The durability period of DPF is considered not so long, and therefore, the longer the use period is, the larger the cost effectiveness of CNG vehicle is than that of diesel car with DPF. (NEDO)

  4. FY 2001 report on the results of the trend survey of introduction of clean energy vehicle for the transport industry; 2001 nendo unso yo clean energy jidosha no donyu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    Survey/analysis were made on the details of the plan on the leading introduction of clean energy vehicle by 632 transporters who applied for the project on promotion of clean energy vehicle in FY 2001. As a result of the survey, the following were made clear. The clean energy vehicles to be planned to be introduced by transporters are all natural gas vehicles. The transporters planning the leading introduction are mostly in large cities and are spreading also in the periphery. Fifty three percent of the transporters predicts that the predicted average running distance of the clean energy vehicle to be introduced is the same as those of the vehicles they owns, and 39% predicts that it is shorter. About the form of utilization, they use it overwhelmingly for the regional collection/delivery. It is considered that the improvement in running distance per 1 fuel filling of clean energy vehicle will contribute to the spread. Fuel supply stations that the clean energy cars to be introduced use concentrate in the good location. It is necessary to strongly promote preparation of the infrastructure. (NEDO)

  5. NJOY system

    International Nuclear Information System (INIS)

    Gil, Choong Sup; Kim, Jung Do

    1998-01-01

    The NJOY Nuclear Data Processing System is used to convert evaluated nuclear data in ENDF format into forms useful for applications. The NJOY code is a modular computer code designed to read evaluated data in ENDF format, transform the data in various ways, and output the results as libraries designed to be used in various applications. The modules are essentially independent programs, and they communicate with each other using input and output files, plus a very few common variables. The NJOY code can work with neutrons, photons, and charged particles. The evaluated nuclear data are reconstructed to pointwise cross sections from ENDF resonance parameters and interpolation schemes. The pointwise data can be Doppler broadened to the temperatures requested by users. The data in unresolved energy range can be computed to effective self-shielded pointwise cross sections. The cross sections and scattering matrices for free or bound scatterers in the thermal energy range are able to be produced. The self-shielded multigroup cross sections, group-to-group scattering matrices, photon-production matrices, and charged-particle cross sections from pointwise data can be generated for various application codes

  6. Chem systems

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper reports that world styrene demand, paced by a near doubling of combined requirements in East Asia and Oceania, could reach 19.3 million metric tons by 2000, an average growth rate of 3.7%/year. So concludes Chem Systems Inc., Tarrytown, N.Y., in a study of world styrene markets through the end of the century. Pacific Rim styrene production and consumption throughout the 1990s are predicted to make up increasingly larger shares of world markets, while demand and production lag in the U.S. and western Europe. Demand and capacity in other parts of the world will grow in real terms, increasing combined market shares only slightly. Most of the increase will be driven by demand in East Asia and Oceania, where consumption by century's end is expected to increase 4.48 million metric tons from 2.25 million tons in 1991. Meantime, Japan's styrene demand in 2000 is projected at 2.64 million tons, a 500,000 ton increase from 1991 demand but a net market loss of 1.9%

  7. FY1995 dynamically up-gradable machine based on right quality control and its life cycle support; 1995 nendo tekisei hinshitsu seigyo ni motozuku doteki seicho kikai to sono lifecycle shien

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A method for determining part re-use and recycling strategy in product design is considered for optimal design of total product life cycle based on the concept of Right Quality Products. For this purpose, it is important to be able to estimate part deterioration status under various product usage conditions. For supporting product designers' decision making about the product life cycle in preliminary design phase, the deterioration estimation is not required to be very exact, but to generate every possible deterioration modes qualitatively. Then, based on these deterioration modes, functional behaviour of target products is simulated, and possible product failure modes can be generated. By utilizing the FMEA (Failure Mode and Effect Analysis) method, the effects of failure modes are evaluated, and the results are fed back to product designers for confirming their design in terms of total product life cycle optimization. A basic methodology is considered, and case study has been done for a mechanical assembly of a one-time use camera. The assembly consists of injection molded parts. Various CAE methods have been used for predicting possible part failures due to initial residual stress, warp, fatigue, creep, and wear. Then kinematic and dynamic analysis of mechanical assembly has been done for detecting the effect of part deterioration on mechanism movements. Several critical failure modes have been detected, and the effects of those failures have been checked by the FMEA method. (NEDO)

  8. Report on investigation in fiscal 2000 of actual status of technological cooperation in foreign market entry supporting organizations in fiscal 2000; 2000 nendo kaigai shinshutsu shien kikan ni okeru gijutsu renkei jittai chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to help improve the business creation supporting environment in Japan, investigations were performed on cases of advanced business creation supporting infrastructures, centering on the United States. The activity results were put into order in the following six fields: 1) creator support and incubators in the United States, 2) the current status of incubators in the United States, 3) support on creation by universities and research institutions, 4) advantages of industry-academia cooperation on creation support, 5) international cooperation in the state of Pennsylvania with other countries, and 6) conclusion. In Item 6), the evolution of the incubator concept in the United States, roles of incubators in areas in which general business creation infrastructures have matured, creator support by universities and education organizations, and matters expected on incubators were summarized. Based on the summarisation, four items were proposed, including structuring of the Japanese type business creation infrastructures to structure a fusion and circulation model for the Japanese type business creation support and economic development, and district economy development under the initiative of business communities. (NEDO)

  9. Fiscal 1996 New Sunshine Plan auxiliary project. Report on results on development of coal hydrogasification technology (Support research); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Sekitan suiso tenka gaska gijutsu kaihatsu shien kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted for the purpose of developing the alternative natural gas manufacturing process that, using coal as the raw material, is highly efficient as well as environmentally superior, with the fiscal 1996 results reported. A test research was carried out on the coal hydrogasification process which was selected as the optimum process based on the studies in the previous years. On the basis of the results of the studies, a free fall pyrolyzer was employed as the test equipment for the use of behavior research of hetero-elements in the test. The basic specifications were set based on a hydrogen/coal ratio of 0.2, a temperature of 950 degrees C and a pressure of 7 MPa, which are the reaction conditions of the ARCH reactor, with the basic design drafted accordingly. In a preliminary examination on the mechanisms of the coal hydrogasification reaction, analysis was made on the representative 20 different kinds of coals, on the six kinds of which studies were made on the gasification behavior using a constant heating rate pyrolyzer. As a result, from the temperature dependency of a methane forming speed, it was assumed that three components of coal had bearing upon the gasification behavior. (NEDO)

  10. Fiscal 1998 New Sunshine Plan auxiliary project. Report on results on development of coal hydrogasification technology (Support research); 1998 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Sekitan suiso tenka gaska gijutsu kaihatsu shien kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    R and D was conducted for the purpose of developing the alternative natural gas manufacturing process that, using coal as the raw material, is highly efficient as well as environmentally superior, with the fiscal 1998 results reported. A hydrogasification test was conducted on Taiheiyo coal at a temperature of 1,173k and a pressure of 7 MPa, which showed that all gaseous products other than methane stopped their evolution roughly in the heat-up process, while methane continued to evolve to show the highest yield. In the reactivity comparison of various types of coal, coals with carbon content of 80% or below were high in reactivity and considered suitable for hydrogasification feedstock. It was also suggested that the hydrogasification reactivity of low rank coals including sub-bituminous coals or below might be greatly affected by the presence/absence of the catalytic effects of ion-exchanged metals. Behavior experiments of sulfur and nitrogen in coal in the hydrogenation reaction were carried out using a continuous free-fall type reactor, which elucidated the effects of hydrogen pressure and gas residence time among various operational elements. (NEDO)

  11. FY1995 dynamically up-gradable machine based on right quality control and its life cycle support; 1995 nendo tekisei hinshitsu seigyo ni motozuku doteki seicho kikai to sono lifecycle shien

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A method for determining part re-use and recycling strategy in product design is considered for optimal design of total product life cycle based on the concept of Right Quality Products. For this purpose, it is important to be able to estimate part deterioration status under various product usage conditions. For supporting product designers' decision making about the product life cycle in preliminary design phase, the deterioration estimation is not required to be very exact, but to generate every possible deterioration modes qualitatively. Then, based on these deterioration modes, functional behaviour of target products is simulated, and possible product failure modes can be generated. By utilizing the FMEA (Failure Mode and Effect Analysis) method, the effects of failure modes are evaluated, and the results are fed back to product designers for confirming their design in terms of total product life cycle optimization. A basic methodology is considered, and case study has been done for a mechanical assembly of a one-time use camera. The assembly consists of injection molded parts. Various CAE methods have been used for predicting possible part failures due to initial residual stress, warp, fatigue, creep, and wear. Then kinematic and dynamic analysis of mechanical assembly has been done for detecting the effect of part deterioration on mechanism movements. Several critical failure modes have been detected, and the effects of those failures have been checked by the FMEA method. (NEDO)

  12. System safety education focused on system management

    Science.gov (United States)

    Grose, V. L.

    1971-01-01

    System safety is defined and characteristics of the system are outlined. Some of the principle characteristics include role of humans in hazard analysis, clear language for input and output, system interdependence, self containment, and parallel analysis of elements.

  13. Systems Biology and Health Systems Complexity in;

    NARCIS (Netherlands)

    Donald Combs, C.; Barham, S.R.; Sloot, P.M.A.

    2016-01-01

    Systems biology addresses interactions in biological systems at different scales of biological organization, from the molecular to the cellular, organ, organism, societal, and ecosystem levels. This chapter expands on the concept of systems biology, explores its implications for individual patients

  14. Airport Information Retrieval System (AIRS) System Design

    Science.gov (United States)

    1974-07-01

    This report presents the system design for a prototype air traffic flow control automation system developed for the FAA's Systems Command Center. The design was directed toward the immediate automation of airport data for use in traffic load predicti...

  15. System specifications for the NDS Dictionary System

    International Nuclear Information System (INIS)

    Attree, P.M.; Smith, P.M.

    1979-09-01

    The NDS Dictionary System is a computerized system for maintaining and distributing the EXFOR dictionaries and for preparing internal versions of these dictionaries for use in the NDS EXFOR System and other NDS systems. This document is an internal manual for the system specifications of the NDS Dictionary System. It includes flow charts, system and program summaries, input and output specifications and file and record descriptions. This manual is updated from time to time when system modifications are made; this is the version of January 1979

  16. Quality management system

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Mu Sung

    2009-08-15

    This book deals with ISO9001 quality management system which includes summary of this system such as classification of quality, principle of quality management, and definition, requirement and procedure of quality management system, introduction of ISO9001 system like model of ISO9001 quality management system, ISO certificate system, structure of ISO9001 standard, requirement of ISO9001 quality management system, process approach and documentation of system, propel cases of ISO9001 quality management system.

  17. Quality management system

    International Nuclear Information System (INIS)

    Lee, Mu Sung

    2009-08-01

    This book deals with ISO9001 quality management system which includes summary of this system such as classification of quality, principle of quality management, and definition, requirement and procedure of quality management system, introduction of ISO9001 system like model of ISO9001 quality management system, ISO certificate system, structure of ISO9001 standard, requirement of ISO9001 quality management system, process approach and documentation of system, propel cases of ISO9001 quality management system.

  18. Protecting Information in Systems of Systems

    NARCIS (Netherlands)

    Trivellato, Daniel; Zannone, Nicola; Etalle, Sandro

    2011-01-01

    Systems of Systems (SoS) are dynamic, distributed coalitions of autonomous and heterogeneous systems that collaborate to achieve a common goal. While offering several advantages in terms of scalability and flexibility, the SoS paradigm has a strong impact on system interoperability and on the

  19. A security framework for systems of systems

    NARCIS (Netherlands)

    Trivellato, D.; Zannone, N.; Etalle, S.

    2011-01-01

    Systems of systems consist of a wide variety of dynamic, distributed coalitions of autonomous and heterogeneous systems that collaborate to achieve a common goal. While offering several advantages in terms of scalability and flexibility, this new paradigm has a strong impact on system

  20. A Security Framework for Systems of Systems

    NARCIS (Netherlands)

    Trivellato, Daniel; Zannone, Nicola; Etalle, Sandro

    2011-01-01

    Systems of systems consist of a wide variety of dynamic, distributed coalitions of autonomous and heterogeneous systems that collaborate to achieve a common goal. While offering several advantages in terms of scalability and flexibility, this new paradigm has a strong impact on system

  1. Systems theory of interconnected port contact systems

    NARCIS (Netherlands)

    Eberard, D.; Maschke, B.M.; Schaft, A.J. van der

    2005-01-01

    Port-based network modeling of a large class of complex physical systems leads to dynamical systems known as port-Hamiltonian systems. The key ingredient of any port-Hamiltonian system is a power-conserving interconnection structure (mathematically formalized by the geometric notion of a Dirac

  2. Digital processing data communication systems (bus systems)

    International Nuclear Information System (INIS)

    Fleck, K.

    1980-01-01

    After an introduction to the technology of digital processing data communication systems there are the following chapters: digital communication of processing data in automation technology, the technology of biserial communication, the implementaiton of a bus system, the data transmission of the TDC-2000 system of Honeywell's and the process bus CS 275 in the automation system TELEPERM M of Siemens AG. (WB) [de

  3. Networked control of microgrid system of systems

    Science.gov (United States)

    Mahmoud, Magdi S.; Rahman, Mohamed Saif Ur; AL-Sunni, Fouad M.

    2016-08-01

    The microgrid has made its mark in distributed generation and has attracted widespread research. However, microgrid is a complex system which needs to be viewed from an intelligent system of systems perspective. In this paper, a network control system of systems is designed for the islanded microgrid system consisting of three distributed generation units as three subsystems supplying a load. The controller stabilises the microgrid system in the presence of communication infractions such as packet dropouts and delays. Simulation results are included to elucidate the effectiveness of the proposed control strategy.

  4. D0 Cryo System Control System Autodialer

    Energy Technology Data Exchange (ETDEWEB)

    Urbin, J.; /Fermilab

    1990-04-17

    The DO cryogenic system is controlled by a TI565-PLC based control system. This allows the system to be unmanned when in steady state operation. System experts will need to be contacted when system parameters exceed normal operating points and reach alarm setpoints. The labwide FIRUS system provides one alarm monitor and communication link. An autodialer provides a second and more flexible alarm monitor and communication link. The autodialer monitors contact points in the control system and after receiving indication of an alarm accesses a list of experts which it calls until it receives an acknowledgement. There are several manufacturers and distributors of autodialer systems. This EN explains the search process the DO cryo group used to fmd an autodialer system that fit the cryo system's needs and includes information and specs for the unit we chose.

  5. Superspeed Maglev system Transrapid. System decription

    Energy Technology Data Exchange (ETDEWEB)

    Miller, L [Thyssen Henschel AG,, Maglev Transportation Technology, Muenchen (Germany)

    1996-12-31

    The superspeed maglev system Transrapid is a track-bound transportation system for passengern and priority freight transport. The transrapid trainsets are composed of self-sufficient vehicle section coupled together. The superspeed maglev system Transrapid is capable of revenue operation at speeds of 100 to 500 km/h. Besides the description of the system concept and system characteristics safety and availability are discussed. (HW)

  6. System design specification Brayton Isotope Power System (BIPS) Flight System (FS), and Ground Demonstration System (GDS)

    International Nuclear Information System (INIS)

    1976-01-01

    The system design specification for ground demonstration, development, and flight qualification of a Brayton Isotope Power System (BIPS) is presented. The requirements for both a BIPS conceptual Flight System (FS) and a Ground Demonstration System (GDS) are defined

  7. A systematic review and meta-analysis on the use of prophylactic topical antibiotics for the prevention of uncomplicated wound infections

    Directory of Open Access Journals (Sweden)

    Tong Q

    2018-03-01

    Full Text Available Qiao-Jing Tong,1 Kimberly DP Hammer,2,3 Erika M Johnson,4 Milagros Zegarra,2,3 Michihiko Goto,5,6 Tze Shien Lo3,7 1Department of Infection Control, Sir Run Run Shaw Hospital, School of Medicine, Zhejiang University, Hangzhou, Zhejiang, China; 2Research Service, Fargo VA Health Care System; 3Department of Internal Medicine, University of North Dakota, School of Medicine and Health Sciences, Fargo, ND, USA; 4Library Resources, University of North Dakota, School of Medicine and Health Sciences, Fargo, ND, USA; 5Center for Comprehensive Access & Delivery Research & Evaluation (CADRE, Iowa City VA Health Care System, West Iowa City, IA, USA; 6Department of Internal Medicine, University of Iowa, Carver College of Medicine, Iowa City, IA, USA; 7Infectious Disease Service, Fargo VA Health Care System, Fargo, ND, USA Background: The prescription of topical antibiotics for the prevention of infections in uncomplicated wounds is common. However, the efficacy is not well reported. Therefore, the objective of the study was to conduct a systematic review and meta-analysis of the available evidence on prevention of uncomplicated wound infections by prophylactic topical antibiotics. Materials and methods: The search included Pubmed, Google Scholar, SCOPUS, Embase, Cochrane, ClinicalTrials.gov, International Clinical Trials Registry Platform, National Technical Information Service, and the National Guidelines Clearinghouse. Results: We identified eight randomized controlled trials and four quasi-randomized trials that met the criteria for the systematic review. Of these trials, 11 studies were pooled for meta-analysis to compare the effects of topical antibiotics versus placebo and 4 studies were pooled for comparison of effects of topical antibiotics versus topical antiseptics on uncomplicated wounds. Fewer wound infections occurred in the topical antibiotic arms compared to placebo (pooled risk ratio: 0.57 [95% CI: 0.37 to 0.86]; p=0.01 and pooled risk

  8. Situation awareness with systems of systems

    CERN Document Server

    Tretmans, Jan; Borth, Michael

    2013-01-01

    This book discusses various aspects, challenges, and solutions for developing systems-of-systems for situation awareness, using applications in the domain of maritime safety and security.  Topics include advanced, multi-objective visualization methods for situation awareness, stochastic outlier selection, rule-based anomaly detection, an ontology-based event model for semantic reasoning, new methods for semi-automatic generation of adapters bridging communication gaps, security policies for systems-of-systems, trust assessment, and methods to deal with the dynamics of systems-of-systems in run-time monitoring, testing, and diagnosis. Architectural considerations for designing information-centric systems-of-systems such as situation awareness systems, and an integrated demonstrator implementing many of the investigated aspects, complete the book.

  9. System specifications for the NDS EXFOR System

    International Nuclear Information System (INIS)

    Attree, P.M.; Smith, P.M.

    1979-07-01

    EXFOR is the agreed exchange format for the magnetic-tape exchange of nuclear reaction data between national and international nuclear data centres for the benefit of nuclear data users in all countries. The NDS EXFOR System is a computerized system for the storage and retrieval of EXFOR information compiled or received by the IAEA. This document is an internal manual for the system specifications of the NDS EXFOR System. It includes flow charts, system and program summaries, input and output specifications and file and record descriptions. The manual is updated from time to time when system modifications are made

  10. System specifications for the NDS EXFOR System

    Energy Technology Data Exchange (ETDEWEB)

    Attree, P M; Smith, P M

    1982-06-01

    EXFOR is the agreed exchange format for the magnetic-tape exchange of nuclear reaction data between national and international nuclear data centers for the benefit of nuclear data users in all countries. The NDS EXFOR System is a computerized system for the storage and retrieval of EXFOR information compiled or received of the IAEA. This document is an internal manual for the system specifications of the NDS EXFOR System. It includes flow charts, system and program summaries, input and output specifications and file and record descriptions. The manual is updated from time to time when system modifications are made; the first version was issued in July 1979. (author)

  11. Computer System Design System-on-Chip

    CERN Document Server

    Flynn, Michael J

    2011-01-01

    The next generation of computer system designers will be less concerned about details of processors and memories, and more concerned about the elements of a system tailored to particular applications. These designers will have a fundamental knowledge of processors and other elements in the system, but the success of their design will depend on the skills in making system-level tradeoffs that optimize the cost, performance and other attributes to meet application requirements. This book provides a new treatment of computer system design, particularly for System-on-Chip (SOC), which addresses th

  12. Smart electromechanical systems the central nervous system

    CERN Document Server

    Kurbanov, Vugar

    2017-01-01

    This book describes approaches to solving the problems of developing the central nervous system of robots (CNSR) based on smart electromechanical systems (SEMS) modules, principles of construction of the various modules of the central nervous system and variants of mathematical software CNSR in control systems for intelligent robots. It presents the latest advances in theory and practice at the Russian Academy of Sciences. Developers of intelligent robots to solve modern problems in robotics are increasingly addressing the use of the bionic approach to create robots that mimic the complexity and adaptability of biological systems. These have smart electromechanical system (SEMS), which are used in various cyber-physical systems (CPhS), and allow the functions of calculation, control, communications, information storage, monitoring, measurement and control of parameters and environmental parameters to be integrated. The behavior of such systems is based on the information received from the central nervous syst...

  13. Multiobjective Collaborative Optimization of Systems of Systems

    National Research Council Canada - National Science Library

    Wolf, Robert A

    2005-01-01

    ...; in other words an inefficient design of the system of systems. This thesis examines the simultaneous design of several ships using the sea base concept as an example application of a network of ships working together...

  14. Situation Awareness with Systems of Systems

    NARCIS (Netherlands)

    Laar, P. van de; Tretmans, J.; Borth, M.

    2013-01-01

    This book discusses various aspects, challenges, and solutions for developing systems-of-systems for situation awareness, using applications in the domain of maritime safety and security. Topics include advanced, multi-objective visualization methods for situation awareness, stochastic outlier

  15. Linking Political Systems and War Systems

    DEFF Research Database (Denmark)

    Harste, Gorm

    2009-01-01

    Decisive parts of the Western political system have demonstrated a seemingly surprising misinterpretation of military might. As Madelaine Albright has suggested, the mighty perceived themselves as "almighty". Political power seems to have invested in instrumental coercive power relations and found...... military coercion to be the appropriate mean. Using the system theory and the theory of systemic risks displayed by the German sociologist Niklas Luhmann the article demonstrates how military systems due to their own autonomy and autopoiesis do not fit into the idea of political government....... The Clausewitzian ideal of a political system that could continue its power games by means of war was moderated by Clausewitz' own analysis of "friction". How can a political system be so blind towards the possibilities of another system? What are the risks of systemic blind spots? The argument of the paper...

  16. Designing information systems

    CERN Document Server

    Blethyn, Stanley G

    2014-01-01

    Designing Information Systems focuses on the processes, methodologies, and approaches involved in designing information systems. The book first describes systems, management and control, and how to design information systems. Discussions focus on documents produced from the functional construction function, users, operators, analysts, programmers and others, process management and control, levels of management, open systems, design of management information systems, and business system description, partitioning, and leveling. The text then takes a look at functional specification and functiona

  17. Cognitive Medical Multiagent Systems

    OpenAIRE

    Barna Iantovics

    2010-01-01

    The development of efficient and flexible agent-based medical diagnosis systems represents a recent research direction. Medical multiagent systems may improve the efficiency of traditionally developed medical computational systems, like the medical expert systems. In our previous researches, a novel cooperative medical diagnosis multiagent system called CMDS (Contract Net Based Medical Diagnosis System) was proposed. CMDS system can solve flexibly a large variety of medical diagnosis problems...

  18. Non linear system become linear system

    Directory of Open Access Journals (Sweden)

    Petre Bucur

    2007-01-01

    Full Text Available The present paper refers to the theory and the practice of the systems regarding non-linear systems and their applications. We aimed the integration of these systems to elaborate their response as well as to highlight some outstanding features.

  19. System Design of the SWRL Financial System.

    Science.gov (United States)

    Ikeda, Masumi

    To produce various management and accounting reports in order to maintain control of SWRL (Southwest Regional Laboratory) operational and financial activities, a computer-based SWRL financial system was developed. The system design is outlined, and various types of system inputs described. The kinds of management and accounting reports generated…

  20. Triggering system innovation in agricultural innovation systems

    NARCIS (Netherlands)

    Turner, James A.; Williams, Tracy; Nicholas, Graeme; Foote, Jeff; Rijswijk, Kelly; Barnard, Tim; Beechener, Sam; Horita, Akiko

    2017-01-01

    This article describes a process for stimulating engagement among change agents to develop a shared understanding of systemic problems in the agricultural innovation system (AIS), challenge prevalent institutional logics and identify actions they might undertake to stimulate system innovation.

  1. Port contact systems for irreversible thermodynamical systems

    NARCIS (Netherlands)

    Eberard, D.; Maschke, B.M.; Schaft, A.J. van der

    2005-01-01

    In this paper we propose a definition of control contact systems, generalizing input-output Hamiltonian systems, to cope with models arising from irreversible Thermodynamics. We exhibit a particular subclass of these systems, called conservative, that leaves invariant some Legendre submanifold (the

  2. Modeling learning technology systems as business systems

    NARCIS (Netherlands)

    Avgeriou, Paris; Retalis, Symeon; Papaspyrou, Nikolaos

    2003-01-01

    The design of Learning Technology Systems, and the Software Systems that support them, is largely conducted on an intuitive, ad hoc basis, thus resulting in inefficient systems that defectively support the learning process. There is now justifiable, increasing effort in formalizing the engineering

  3. General Systems Theory and Instructional Systems Design.

    Science.gov (United States)

    Salisbury, David F.

    1990-01-01

    Describes basic concepts in the field of general systems theory (GST) and identifies commonalities that exist between GST and instructional systems design (ISD). Models and diagrams that depict system elements in ISD are presented, and two matrices that show how GST has been used in ISD literature are included. (11 references) (LRW)

  4. Expert systems in process control systems

    International Nuclear Information System (INIS)

    Wittig, T.

    1987-01-01

    To illustrate where the fundamental difference between expert systems in classical diagnosis and in industrial control lie, the work of process control instrumentation is used as an example for the job of expert systems. Starting from the general process of problem-solving, two classes of expert systems can be defined accordingly. (orig.) [de

  5. Expert Systems for auditing management information systems

    Directory of Open Access Journals (Sweden)

    Gheroghe Popescu

    2007-05-01

    Full Text Available Expert systems are built with the help of: specialised programming languages or expert system generators (shell. But this structure was reached after tens of years of work and research, because expert systems are nothing but pragmatic capitalisation of the results of research carried out in artificial intelligence and theory of knowledge.

  6. Psychology of system design

    CERN Document Server

    Meister, D

    2014-01-01

    This is a book about systems, including: systems in which humans control machines; systems in which humans interact with humans and the machine component is relatively unimportant; systems which are heavily computerized and those that are not; and governmental, industrial, military and social systems. The book deals with both traditional systems like farming, fishing and the military, and with systems just now tentatively emerging, like the expert and the interactive computer system. The emphasis is on the system concept and its implications for analysis, design and evaluation of these many di

  7. Biomedical signals and systems

    CERN Document Server

    Tranquillo, Joseph V

    2013-01-01

    Biomedical Signals and Systems is meant to accompany a one-semester undergraduate signals and systems course. It may also serve as a quick-start for graduate students or faculty interested in how signals and systems techniques can be applied to living systems. The biological nature of the examples allows for systems thinking to be applied to electrical, mechanical, fluid, chemical, thermal and even optical systems. Each chapter focuses on a topic from classic signals and systems theory: System block diagrams, mathematical models, transforms, stability, feedback, system response, control, time

  8. Operating System Security

    CERN Document Server

    Jaeger, Trent

    2008-01-01

    Operating systems provide the fundamental mechanisms for securing computer processing. Since the 1960s, operating systems designers have explored how to build "secure" operating systems - operating systems whose mechanisms protect the system against a motivated adversary. Recently, the importance of ensuring such security has become a mainstream issue for all operating systems. In this book, we examine past research that outlines the requirements for a secure operating system and research that implements example systems that aim for such requirements. For system designs that aimed to

  9. Systems Measures of Water Distribution System Resilience

    Energy Technology Data Exchange (ETDEWEB)

    Klise, Katherine A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Murray, Regan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Walker, La Tonya Nicole [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-01-01

    Resilience is a concept that is being used increasingly to refer to the capacity of infrastructure systems to be prepared for and able to respond effectively and rapidly to hazardous events. In Section 2 of this report, drinking water hazards, resilience literature, and available resilience tools are presented. Broader definitions, attributes and methods for measuring resilience are presented in Section 3. In Section 4, quantitative systems performance measures for water distribution systems are presented. Finally, in Section 5, the performance measures and their relevance to measuring the resilience of water systems to hazards is discussed along with needed improvements to water distribution system modeling tools.

  10. Manager's assistant systems for space system planning

    Science.gov (United States)

    Bewley, William L.; Burnard, Robert; Edwards, Gary E.; Shoop, James

    1992-01-01

    This paper describes a class of knowledge-based 'assistant' systems for space system planning. Derived from technology produced for the DARPA/USAF Pilot's Associate program, these assistant systems help the human planner by doing the bookkeeping to maintain plan data and executing the procedures and heuristics currently used by the human planner to define, assess, diagnose, and revise plans. Intelligent systems for Space Station Freedom assembly sequence planning and Advanced Launch System modeling will be presented as examples. Ongoing NASA-funded work on a framework supporting the development of such tools will also be described.

  11. Lighting system with thermal management system

    Science.gov (United States)

    Arik, Mehmet; Weaver, Stanton; Stecher, Thomas; Seeley, Charles; Kuenzler, Glenn; Wolfe, Jr., Charles; Utturkar, Yogen; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

    2013-05-07

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

  12. EPICS based DAQ system

    International Nuclear Information System (INIS)

    Cheng Weixing; Chen Yongzhong; Zhou Weimin; Ye Kairong; Liu Dekang

    2002-01-01

    EPICS is the most popular developing platform to build control system and beam diagnostic system in modern physics experiment facilities. An EPICS based data acquisition system was built in Redhat 6.2 operation system. The system is successfully used in the beam position monitor mapping, it improves the mapping process a lot

  13. Autonomous photovoltaic lighting system

    OpenAIRE

    Hafez, Ahmed A. A.; Montesinos Miracle, Daniel; Sudrià Andreu, Antoni

    2012-01-01

    This paper introduces a comparison between the conventional and Photovoltaic (PV) lighting systems. A simple sizing procedure for a PV stand-alone system was advised. The paper also proposes a novel PV lighting system. The proposed system is simple, compact and reliable. The system operation was investigated by thoroughly mathematical and simulation work.

  14. FFTF control system experience

    International Nuclear Information System (INIS)

    Warrick, R.P.

    1981-01-01

    The FFTF control systems provide control equipment for safe and efficient operation of the plant. For convenience, these systems will be divided into three parts for discussions: (1) Plant Protection System (PPS); (2) Plant Control System (PCS); and (3) General Observations. Performance of each of these systems is discussed

  15. Automatic control systems engineering

    International Nuclear Information System (INIS)

    Shin, Yun Gi

    2004-01-01

    This book gives descriptions of automatic control for electrical electronics, which indicates history of automatic control, Laplace transform, block diagram and signal flow diagram, electrometer, linearization of system, space of situation, state space analysis of electric system, sensor, hydro controlling system, stability, time response of linear dynamic system, conception of root locus, procedure to draw root locus, frequency response, and design of control system.

  16. MEA vacuum system

    International Nuclear Information System (INIS)

    Stroo, R.; Schwebke, H.; Heine, E.

    1984-01-01

    This report describes construction and operation of the MEA vacuum system of NIKHEF (Netherlands). First, the klystron vacuum system, beam transport system, diode pump and a triode pump are described. Next, the isolation valve and the fast valves of the vacuum system are considered. Measuring instruments, vacuum system commands and messages of failures are treated in the last chapter. (G.J.P.)

  17. From systems biology to systems biomedicine.

    Science.gov (United States)

    Antony, Paul M A; Balling, Rudi; Vlassis, Nikos

    2012-08-01

    Systems Biology is about combining theory, technology, and targeted experiments in a way that drives not only data accumulation but knowledge as well. The challenge in Systems Biomedicine is to furthermore translate mechanistic insights in biological systems to clinical application, with the central aim of improving patients' quality of life. The challenge is to find theoretically well-chosen models for the contextually correct and intelligible representation of multi-scale biological systems. In this review, we discuss the current state of Systems Biology, highlight the emergence of Systems Biomedicine, and highlight some of the topics and views that we think are important for the efficient application of Systems Theory in Biomedicine. Copyright © 2011 Elsevier Ltd. All rights reserved.

  18. Mapping biological systems to network systems

    CERN Document Server

    Rathore, Heena

    2016-01-01

    The book presents the challenges inherent in the paradigm shift of network systems from static to highly dynamic distributed systems – it proposes solutions that the symbiotic nature of biological systems can provide into altering networking systems to adapt to these changes. The author discuss how biological systems – which have the inherent capabilities of evolving, self-organizing, self-repairing and flourishing with time – are inspiring researchers to take opportunities from the biology domain and map them with the problems faced in network domain. The book revolves around the central idea of bio-inspired systems -- it begins by exploring why biology and computer network research are such a natural match. This is followed by presenting a broad overview of biologically inspired research in network systems -- it is classified by the biological field that inspired each topic and by the area of networking in which that topic lies. Each case elucidates how biological concepts have been most successfully ...

  19. Local sustained delivery of acetylsalicylic acid via hybrid stent with biodegradable nanofibers reduces adhesion of blood cells and promotes reendothelialization of the denuded artery

    Directory of Open Access Journals (Sweden)

    Lee CH

    2014-01-01

    Full Text Available Cheng-Hung Lee,1,2 Yu-Huang Lin,3 Shang-Hung Chang,1 Chun-Der Tai,3 Shih-Jung Liu,2 Yen Chu,4 Chao-Jan Wang,5 Ming-Yi Hsu,5 Hung Chang,6 Gwo-Jyh Chang,7 Kuo-Chun Hung,1 Ming-Jer Hsieh,1 Fen-Chiung Lin,1 I-Chang Hsieh,1 Ming-Shien Wen,1 Yenlin Huang81Division of Cardiology, Department of Internal Medicine, Chang Gung Memorial Hospital, Chang Gung University College of Medicine, Linkou, 2Department of Mechanical Engineering, 3Graduate Institute of Medical Mechatronics, Chang Gung University, 4Laboratory of Cardiovascular Physiology, Division of Thoracic and Cardiovascular Surgery, 5Department of Medical Imaging and Intervention, 6Hematology-Oncology Division, Department of Internal Medicine, Chang Gung Memorial Hospital, Linkou, 7Graduate Institute of Clinical Medicinal Sciences, Chang Gung University College of Medicine, Linkou, 8Department of Anatomical Pathology, Chang Gung Memorial Hospital, Linkou, Tao-Yuan, TaiwanAbstract: Incomplete endothelialization, blood cell adhesion to vascular stents, and inflammation of arteries can result in acute stent thromboses. The systemic administration of acetylsalicylic acid decreases endothelial dysfunction, potentially reducing thrombus, enhancing vasodilatation, and inhibiting the progression of atherosclerosis; but, this is weakened by upper gastrointestinal bleeding. This study proposes a hybrid stent with biodegradable nanofibers, for the local, sustained delivery of acetylsalicylic acid to injured artery walls. Biodegradable nanofibers are prepared by first dissolving poly(D,L-lactide-co-glycolide and acetylsalicylic acid in 1,1,1,3,3,3-hexafluoro-2-propanol. The solution is then electrospun into nanofibrous tubes, which are then mounted onto commercially available bare-metal stents. In vitro release rates of pharmaceuticals from nanofibers are characterized using an elution method, and a high-performance liquid chromatography assay. The experimental results suggest that biodegradable nanofibers

  20. Environmental Management System

    Science.gov (United States)

    Goals Recycling Green Purchasing Pollution Prevention Reusing Water Resources Environmental Management Stewardship » Environmental Protection » Environmental Management System Environmental Management System An Environmental Management System is a systematic method for assessing mission activities, determining the

  1. System floorplanning optimization

    KAUST Repository

    Browning, David W.; Elansary, Ayman; Shalaby, Mohamed

    2012-01-01

    Notebook and Laptop Original Equipment Manufacturers (OEMs) place great emphasis on creating unique system designs to differentiate themselves in the mobile market. These systems are developed from the 'outside in' with the focus on how the system

  2. Connected motorcycle system performance.

    Science.gov (United States)

    2016-01-15

    This project characterized the performance of Connected Vehicle Systems (CVS) on motorcycles based on two key components: global positioning and wireless communication systems. Considering that Global Positioning System (GPS) and 5.9 GHz Dedicated Sh...

  3. Antiskid braking system

    Science.gov (United States)

    Pazdera, J. S.

    1974-01-01

    Published report describes analytical development and simulation of braking system. System prevents wheels from skidding when brakes are applied, significantly reducing stopping distance. Report also presents computer simulation study on system as applied to aircraft.

  4. Bridge Management Systems

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle

    In this paper bridge management systems are discussed with special emphasis on management systems for reinforced concrete bridges. Management systems for prestressed concrete bridges, steel bridges, or composite bridges can be developed in a similar way....

  5. TWRSview system requirements specification

    International Nuclear Information System (INIS)

    Caldwell, J.A.; Lee, A.K.

    1995-12-01

    This document provides the system requirements specification for the TWRSview software system. The TWRSview software system is being developed to integrate electronic data supporting the development of the TWRS technical baseline

  6. Calo trigger acquisition system

    CERN Multimedia

    Franchini, Matteo

    2016-01-01

    Calo trigger acquisition system - Evolution of the acquisition system from a multiple boards system (upper, orange cables) to a single board one (below, light blue cables) where all the channels are collected in a single board.

  7. Lungs and Respiratory System

    Science.gov (United States)

    ... Videos for Educators Search English Español Lungs and Respiratory System KidsHealth / For Parents / Lungs and Respiratory System ... ll have taken at least 600 million breaths. Respiratory System Basics All of this breathing couldn't ...

  8. The Trinity System

    Energy Technology Data Exchange (ETDEWEB)

    Archer, Billy Joe [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Vigil, Benny Manuel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-01-13

    This paper describes the Trinity system, the first ASC Advanced Technology System (ATS-1). We describe the Trinity procurement timeline, the ASC computing strategy, the Trinity specific mission needs, and the Trinity system specifications.

  9. Pneumatic transfer systems

    International Nuclear Information System (INIS)

    Bichler, H.; Boeck, H.; Hammer, J.; Buchtela, K.

    1988-11-01

    A pneumatic transfer system for research reactors, including a sample changer system and to be used for neutron activation analysis, is described. The system can be obtained commercially from the Atominstitut. 2 figs. (qui)

  10. Immune System Quiz

    Science.gov (United States)

    ... Safe Videos for Educators Search English Español Quiz: Immune System KidsHealth / For Kids / Quiz: Immune System Print How much do you know about your immune system? Find out by taking this quiz! About Us ...

  11. System floorplanning optimization

    KAUST Repository

    Browning, David W.; Ansary, Ayman M. El; Shalaby, Mohamed

    2013-01-01

    Notebook and Laptop Original Equipment Manufacturers (OEMs) place great emphasis on creating unique system designs to differentiate themselves in the mobile market. These systems are developed from the 'outside in' with the focus on how the system

  12. Autonomic Nervous System Disorders

    Science.gov (United States)

    Your autonomic nervous system is the part of your nervous system that controls involuntary actions, such as the beating of your heart ... breathing and swallowing Erectile dysfunction in men Autonomic nervous system disorders can occur alone or as the result ...

  13. Central Nervous System Vasculitis

    Science.gov (United States)

    ... of Vasculitis / Central Nervous System (CNS) Vasculitis Central Nervous System (CNS) Vasculitis Swap out your current Facebook Profile ... Facebook personal page. Replace with this image. Central nervous system (CNS) vasculitis is inflammation of blood vessel walls ...

  14. Wind energy systems

    Science.gov (United States)

    Stewart, H. J.

    1978-01-01

    A discussion on wind energy systems involved with the DOE wind energy program is presented. Some of the problems associated with wind energy systems are discussed. The cost, efficiency, and structural design of wind energy systems are analyzed.

  15. System Software 7 Macintosh

    CERN Multimedia

    1991-01-01

    System 7 is a single-user graphical user interface-based operating system for Macintosh computers and was part of the classic Mac OS line of operating systems. It was introduced on May 13, 1991, by Apple Computer. It succeeded System 6, and was the main Macintosh operating system until it was succeeded by Mac OS 8 in 1997. Features added with the System 7 release included virtual memory, personal file sharing, QuickTime, QuickDraw 3D, and an improved user interface. This is the first real major evolution of the Macintosh system, bringing a significant improvement in the user interface, improved stability and many new features such as the ability to use multiple applications at the same time. "System 7" is the last operating system name of the Macintosh that contains the word "system". Macintosh operating systems were later called "Mac OS" (for Macintosh Operating System).

  16. Marketing reporting system

    OpenAIRE

    Hanić Hasan M.

    2004-01-01

    The main components of a developed and good organized marketing information system are: internal reporting system, marketing reporting system, market research system and analytical marketing system. Marketing reporting system provides data and information about changes in business and micro marketing environment. This component of MIS ensures that marketing managers are up-to-date with what is going on, and to be informed about changes in company marketing environment.

  17. Marketing reporting system

    Directory of Open Access Journals (Sweden)

    Hanić Hasan M.

    2004-01-01

    Full Text Available The main components of a developed and good organized marketing information system are: internal reporting system, marketing reporting system, market research system and analytical marketing system. Marketing reporting system provides data and information about changes in business and micro marketing environment. This component of MIS ensures that marketing managers are up-to-date with what is going on, and to be informed about changes in company marketing environment.

  18. Propulsion Systems Panel deliberations

    Science.gov (United States)

    Bianca, Carmelo J.; Miner, Robert; Johnston, Lawrence M.; Bruce, R.; Dennies, Daniel P.; Dickenson, W.; Dreshfield, Robert; Karakulko, Walt; Mcgaw, Mike; Munafo, Paul M.

    1993-01-01

    The Propulsion Systems Panel was established because of the specialized nature of many of the materials and structures technology issues related to propulsion systems. This panel was co-chaired by Carmelo Bianca, MSFC, and Bob Miner, LeRC. Because of the diverse range of missions anticipated for the Space Transportation program, three distinct propulsion system types were identified in the workshop planning process: liquid propulsion systems, solid propulsion systems and nuclear electric/nuclear thermal propulsion systems.

  19. Small test SDHW systems

    DEFF Research Database (Denmark)

    Vejen, Niels Kristian

    1999-01-01

    Three small test SDHW systems was tested in a laboratory test facility.The three SDHW systems where all based on the low flow principe and a mantle tank but the design of the systems where different.......Three small test SDHW systems was tested in a laboratory test facility.The three SDHW systems where all based on the low flow principe and a mantle tank but the design of the systems where different....

  20. Battery systems engineering

    CERN Document Server

    Rahn, Christopher D

    2012-01-01

    A complete all-in-one reference on the important interdisciplinary topic of Battery Systems Engineering Focusing on the interdisciplinary area of battery systems engineering, this book provides the background, models, solution techniques, and systems theory that are necessary for the development of advanced battery management systems. It covers the topic from the perspective of basic electrochemistry as well as systems engineering topics and provides a basis for battery modeling for system engineering of electric and hybrid electric vehicle platforms. This original

  1. Gas transfer system

    International Nuclear Information System (INIS)

    Oberlin, J.C.; Frick, G.; Kempfer, C.; North, C.

    1988-09-01

    The state of work on the Vivitron gas transfer system and the system functions are summarized. The system has to: evacuate the Vivitron reservoir; transfer gas from storage tanks to the Vivitron; recirculate gas during operation; transfer gas from the Vivitron to storage tanks; and assure air input. The system is now being installed. Leak alarms are given by SF6 detectors, which set off a system of forced ventilation. Another system continuously monitors the amount of SF6 in the tanks [fr

  2. Cognitive Medical Multiagent Systems

    Directory of Open Access Journals (Sweden)

    Barna Iantovics

    2010-01-01

    Full Text Available The development of efficient and flexible agent-based medical diagnosis systems represents a recent research direction. Medical multiagent systems may improve the efficiency of traditionally developed medical computational systems, like the medical expert systems. In our previous researches, a novel cooperative medical diagnosis multiagent system called CMDS (Contract Net Based Medical Diagnosis System was proposed. CMDS system can solve flexibly a large variety of medical diagnosis problems. This paper analyses the increased intelligence of the CMDS system, which motivates its use for different medical problem’s solving.

  3. Airports Geographic Information System -

    Data.gov (United States)

    Department of Transportation — The Airports Geographic Information System maintains the airport and aeronautical data required to meet the demands of the Next Generation National Airspace System....

  4. Aeronautical Information System -

    Data.gov (United States)

    Department of Transportation — The Aeronautical Information System (AIS) is a leased weather automated system that provides a means of collecting and distributing aeronautical weather information...

  5. Credit Management System

    Data.gov (United States)

    US Agency for International Development — Credit Management System. Outsourced Internet-based application. CMS stores and processes data related to USAID credit programs. The system provides information...

  6. Control system design method

    Science.gov (United States)

    Wilson, David G [Tijeras, NM; Robinett, III, Rush D.

    2012-02-21

    A control system design method and concomitant control system comprising representing a physical apparatus to be controlled as a Hamiltonian system, determining elements of the Hamiltonian system representation which are power generators, power dissipators, and power storage devices, analyzing stability and performance of the Hamiltonian system based on the results of the determining step and determining necessary and sufficient conditions for stability of the Hamiltonian system, creating a stable control system based on the results of the analyzing step, and employing the resulting control system to control the physical apparatus.

  7. Neural Systems Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — As part of the Electrical and Computer Engineering Department and The Institute for System Research, the Neural Systems Laboratory studies the functionality of the...

  8. Integrated Systems Health Management for Intelligent Systems

    Science.gov (United States)

    Figueroa, Fernando; Melcher, Kevin

    2011-01-01

    The implementation of an integrated system health management (ISHM) capability is fundamentally linked to the management of data, information, and knowledge (DIaK) with the purposeful objective of determining the health of a system. It is akin to having a team of experts who are all individually and collectively observing and analyzing a complex system, and communicating effectively with each other in order to arrive at an accurate and reliable assessment of its health. In this paper, concepts, procedures, and approaches are presented as a foundation for implementing an intelligent systems ]relevant ISHM capability. The capability stresses integration of DIaK from all elements of a system. Both ground-based (remote) and on-board ISHM capabilities are compared and contrasted. The information presented is the result of many years of research, development, and maturation of technologies, and of prototype implementations in operational systems.

  9. System Analysis and Risk Assessment (SARA) system

    International Nuclear Information System (INIS)

    Krantz, E.A.; Russell, K.D.; Stewart, H.D.; Van Siclen, V.S.

    1986-01-01

    Utilization of Probabilistic Risk Assessment (PRA) related information in the day-to-day operation of plant systems has, in the past, been impracticable due to the size of the computers needed to run PRA codes. This paper discusses a microcomputer-based database system which can greatly enhance the capability of operators or regulators to incorporate PRA methodologies into their routine decision making. This system is called the System Analysis and Risk Assessment (SARA) system. SARA was developed by EG and G Idaho, Inc. at the Idaho National Engineering Laboratory to facilitate the study of frequency and consequence analyses of accident sequences from a large number of light water reactors (LWRs) in this country. This information is being amassed by several studies sponsored by the United States Nuclear Regulatory Commission (USNRC). To meet the need of portability and accessibility, and to perform the variety of calculations necessary, it was felt that a microcomputer-based system would be most suitable

  10. Systems engineering for very large systems

    Science.gov (United States)

    Lewkowicz, Paul E.

    Very large integrated systems have always posed special problems for engineers. Whether they are power generation systems, computer networks or space vehicles, whenever there are multiple interfaces, complex technologies or just demanding customers, the challenges are unique. 'Systems engineering' has evolved as a discipline in order to meet these challenges by providing a structured, top-down design and development methodology for the engineer. This paper attempts to define the general class of problems requiring the complete systems engineering treatment and to show how systems engineering can be utilized to improve customer satisfaction and profit ability. Specifically, this work will focus on a design methodology for the largest of systems, not necessarily in terms of physical size, but in terms of complexity and interconnectivity.

  11. Epilogue: Systems Approaches and Systems Practice

    Science.gov (United States)

    Reynolds, Martin; Holwell, Sue

    Each of the five systems approaches discussed in this volume: system dynamics (SD), the viable systems model (VSM), strategic options development and analysis (SODA), soft systems methodology (SSM) and critical systems heuristics (CSH) has a pedigree. Not in the sense of the sometimes absurd spectacle of animals paraded at dog shows. Rather, their pedigree derives from their systems foundations, their capacity to evolve and their flexibility in use. None of the five approaches has developed out of use in restricted and controlled contexts of either low or high levels of complicatedness. Neither has any one of them evolved as a consequence of being applied only to situations with either presumed stakeholder agreement on purpose, or courteous disagreement amongst stakeholders, or stakeholder coercion. The compilation is not a celebration of abstract ‘methodologies', but of theoretically robust approaches that have a genuine pedigree in practice.

  12. Systems analysis of a security alarm system

    International Nuclear Information System (INIS)

    Schiff, A.

    1975-01-01

    When the Lawrence Livermore Laboratory found that its security alarm system was causing more false alarms and maintenance costs than LLL felt was tolerable, a systems analysis was undertaken to determine what should be done about the situation. This report contains an analysis of security alarm systems in general and ends with a review of the existing Security Alarm Control Console (SACC) and recommendations for its improvement, growth and change. (U.S.)

  13. Precision digital control systems

    Science.gov (United States)

    Vyskub, V. G.; Rozov, B. S.; Savelev, V. I.

    This book is concerned with the characteristics of digital control systems of great accuracy. A classification of such systems is considered along with aspects of stabilization, programmable control applications, digital tracking systems and servomechanisms, and precision systems for the control of a scanning laser beam. Other topics explored are related to systems of proportional control, linear devices and methods for increasing precision, approaches for further decreasing the response time in the case of high-speed operation, possibilities for the implementation of a logical control law, and methods for the study of precision digital control systems. A description is presented of precision automatic control systems which make use of electronic computers, taking into account the existing possibilities for an employment of computers in automatic control systems, approaches and studies required for including a computer in such control systems, and an analysis of the structure of automatic control systems with computers. Attention is also given to functional blocks in the considered systems.

  14. L-system fractals

    CERN Document Server

    Mishra, Jibitesh

    2007-01-01

    The book covers all the fundamental aspects of generating fractals through L-system. Also it provides insight to various researches in this area for generating fractals through L-system approach & estimating dimensions. Also it discusses various applications of L-system fractals. Key Features: - Fractals generated from L-System including hybrid fractals - Dimension calculation for L-system fractals - Images & codes for L-system fractals - Research directions in the area of L-system fractals - Usage of various freely downloadable tools in this area - Fractals generated from L-System including hybrid fractals- Dimension calculation for L-system fractals- Images & codes for L-system fractals- Research directions in the area of L-system fractals- Usage of various freely downloadable tools in this area

  15. Power system protection 2 systems and methods

    CERN Document Server

    1995-01-01

    The worldwide growth in demand for electricity has forced the pace of developments in electrical power system design to meet consumer needs for reliable, secure and cheap supplies. Power system protection, as a technology essential to high quality supply, is widely recognised as a specialism of growing and often critical importance, in which power system needs and technological progress have combined to result in rapid developments in policy and practice in recent years. In the United Kingdom, the need for appropriate training in power system protection was recognised in the early 1960s with t

  16. Hot Spot Removal System: System description

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    Hazardous wastes contaminated with radionuclides, chemicals, and explosives exist across the Department of Energy complex and need to be remediated due to environmental concerns. Currently, an opportunity is being developed to dramatically reduce remediation costs and to assist in the acceleration of schedules associated with these wastes by deploying a Hot Spot Removal System. Removing the hot spot from the waste site will remove risk driver(s) and enable another, more cost effective process/option/remedial alternative (i.e., capping) to be applied to the remainder of the site. The Hot Spot Removal System consists of a suite of technologies that will be utilized to locate and remove source terms. Components of the system can also be used in a variety of other cleanup activities. This Hot Spot Removal System Description document presents technologies that were considered for possible inclusion in the Hot Spot Removal System, technologies made available to the Hot Spot Removal System, industrial interest in the Hot Spot Removal System`s subsystems, the schedule required for the Hot Spot Removal System, the evaluation of the relevant technologies, and the recommendations for equipment and technologies as stated in the Plan section.

  17. Unmanned Aerial System, New System Manning Prediction

    National Research Council Canada - National Science Library

    Hunn, Bruce P

    2006-01-01

    .... System safety and effectiveness, training, contractor operations and working conditions were evaluated for current UASs, including Hunter, Shadow, Predator, Improved Gnat, and to a lesser degree...

  18. Site systems engineering: Systems engineering management plan

    Energy Technology Data Exchange (ETDEWEB)

    Grygiel, M.L. [Westinghouse Hanford Co., Richland, WA (United States)

    1996-05-03

    The Site Systems Engineering Management Plan (SEMP) is the Westinghouse Hanford Company (WHC) implementation document for the Hanford Site Systems Engineering Policy, (RLPD 430.1) and Systems Engineering Criteria Document and Implementing Directive, (RLID 430.1). These documents define the US Department of Energy (DOE), Richland Operations Office (RL) processes and products to be used at Hanford to implement the systems engineering process at the site level. This SEMP describes the products being provided by the site systems engineering activity in fiscal year (FY) 1996 and the associated schedule. It also includes the procedural approach being taken by the site level systems engineering activity in the development of these products and the intended uses for the products in the integrated planning process in response to the DOE policy and implementing directives. The scope of the systems engineering process is to define a set of activities and products to be used at the site level during FY 1996 or until the successful Project Hanford Management Contractor (PHMC) is onsite as a result of contract award from Request For Proposal DE-RP06-96RL13200. Following installation of the new contractor, a long-term set of systems engineering procedures and products will be defined for management of the Hanford Project. The extent to which each project applies the systems engineering process and the specific tools used are determined by the project`s management.

  19. Hot Spot Removal System: System description

    International Nuclear Information System (INIS)

    1997-09-01

    Hazardous wastes contaminated with radionuclides, chemicals, and explosives exist across the Department of Energy complex and need to be remediated due to environmental concerns. Currently, an opportunity is being developed to dramatically reduce remediation costs and to assist in the acceleration of schedules associated with these wastes by deploying a Hot Spot Removal System. Removing the hot spot from the waste site will remove risk driver(s) and enable another, more cost effective process/option/remedial alternative (i.e., capping) to be applied to the remainder of the site. The Hot Spot Removal System consists of a suite of technologies that will be utilized to locate and remove source terms. Components of the system can also be used in a variety of other cleanup activities. This Hot Spot Removal System Description document presents technologies that were considered for possible inclusion in the Hot Spot Removal System, technologies made available to the Hot Spot Removal System, industrial interest in the Hot Spot Removal System''s subsystems, the schedule required for the Hot Spot Removal System, the evaluation of the relevant technologies, and the recommendations for equipment and technologies as stated in the Plan section

  20. Systems integration of business systems. Business system ni kanshite

    Energy Technology Data Exchange (ETDEWEB)

    Furukawa, H [Nippon Steel Corp., Tokyo (Japan)

    1991-09-26

    System integration (SI) is defined as combining hardwares and softwares as the infrastructures with know-hows for their use comprehensively to respond to high-level needs of users. This paper reports the features of an SI being developed by a company (E Company), its concept on the systematized development methodology, and the conceptual models. With the primary policy placed on creative integration standing on customers positions, the SI concept comprises three parts of models for evaluations as seen from the customers, evaluations as seen from the E Company, and the development object systems to link both parts. The third part is further consisted of several lower hierarchies including a customer controlled system hierarchy (this enables customers to control the system through visualization, for example, and includes three logic models (multiple solution selection, optimal solution under restricted conditions, and numerical solution)). 2 refs., 9 figs.

  1. CDMA systems capacity engineering

    CERN Document Server

    Kim, Kiseon

    2004-01-01

    This new hands-on resource tackles capacity planning and engineering issues that are crucial to optimizing wireless communication systems performance. Going beyond the system physical level and investigating CDMA system capacity at the service level, this volume is the single-source for engineering and analyzing systems capacity and resources.

  2. Smart SDHW systems

    DEFF Research Database (Denmark)

    Andersen, Elsa

    2000-01-01

    The aim of the project is to develop smart solar domestic hot water (SDHW) systems. A smart SDHW is a system in which the domestic water can bee heated both by solar collectors and by an auxiliary energy supply system. The auxiliary energy supply system heats up the hot-water tank from the top an...

  3. Information Systems Security Audit

    OpenAIRE

    Gheorghe Popescu; Veronica Adriana Popescu; Cristina Raluca Popescu

    2007-01-01

    The article covers:Defining an information system; benefits obtained by introducing new information technologies; IT management;Defining prerequisites, analysis, design, implementation of IS; Information security management system; aspects regarding IS security policy; Conceptual model of a security system; Auditing information security systems and network infrastructure security.

  4. Medical imaging systems

    Science.gov (United States)

    Frangioni, John V

    2013-06-25

    A medical imaging system provides simultaneous rendering of visible light and diagnostic or functional images. The system may be portable, and may include adapters for connecting various light sources and cameras in open surgical environments or laparascopic or endoscopic environments. A user interface provides control over the functionality of the integrated imaging system. In one embodiment, the system provides a tool for surgical pathology.

  5. Evolution of ERP systems

    NARCIS (Netherlands)

    Wortmann, J.C.; Bititci, U.S.; Carrie, A.S.

    1998-01-01

    This paper describes the development of ERP systems over time. It explores both the functionality and the technology of ERP-systems. It explains the increased importance of ERP systems in practice. The paper also addresses the difficulties encountered in implementing ERP systems in real life. Modern

  6. Digital processing data communication systems (bus systems). Digitale Prozessdaten-Kommunikations-Systeme (Bus Systeme)

    Energy Technology Data Exchange (ETDEWEB)

    Fleck, K

    1980-01-01

    After an introduction to the technology of digital processing data communication systems there are the following chapters: digital communication of processing data in automation technology, the technology of biserial communication, the implementaiton of a bus system, the data transmission of the TDC-2000 system of Honeywell's and the process bus CS 275 in the automation system TELEPERM M of Siemens AG.

  7. EUCLID ARCHIVE SYSTEM PROTOTYPE

    NARCIS (Netherlands)

    Belikov, Andrey; Williams, Owen; Droge, Bob; Tsyganov, Andrey; Boxhoorn, Danny; McFarland, John; Verdoes Kleijn, Gijs; Valentijn, E; Altieri, Bruno; Dabin, Christophe; Pasian, F.; Osuna, Pedro; Soille, P.; Marchetti, P.G.

    2014-01-01

    The Euclid Archive System prototype is a functional information system which is used to address the numerous challenges in the development of fully functional data processing system for Euclid. The prototype must support the highly distributed nature of the Euclid Science Ground System, with Science

  8. Product Service Systems

    DEFF Research Database (Denmark)

    Departing from Product Development models based on physical artefacts. Moving towards integrated Product Development and System Operations models suited Product/Service-systems......Departing from Product Development models based on physical artefacts. Moving towards integrated Product Development and System Operations models suited Product/Service-systems...

  9. Biogas plant control system

    International Nuclear Information System (INIS)

    Balasevicius, L.; Dervinis, G.; Macerauskas, V.

    2002-01-01

    This paper presents intelligent control system for the pig farm biogas production process. The system uses a fuzzy logic models based on knowledge of experts and operators. Four fuzzy models are introduced. The adequacy of fuzzy models is verified using real data and MATLAB simulation. Proposed expert system is implemented into traditional SCADA system for biogas process prediction and failure analyzing. (authors)

  10. System Performance and Testing

    NARCIS (Netherlands)

    Frei, U.; Oversloot, H.

    2004-01-01

    This chapter compares and contrasts the system performance of two widely used solar thermal systems using testing and simulation programs. Solar thermal systems are used in many countries for heating domestically used water. In addition to the simple thermosiphon systems, better designed pumped

  11. Hybrid intelligent engineering systems

    CERN Document Server

    Jain, L C; Adelaide, Australia University of

    1997-01-01

    This book on hybrid intelligent engineering systems is unique, in the sense that it presents the integration of expert systems, neural networks, fuzzy systems, genetic algorithms, and chaos engineering. It shows that these new techniques enhance the capabilities of one another. A number of hybrid systems for solving engineering problems are presented.

  12. ERP–systems

    OpenAIRE

    Shustova I.

    2016-01-01

    In this work, we analyzed the existing ERP–systems of foreign and domestic manufacturers. Popular ERP–systems in the Republic of Belarus were considered. The leading ERP-systems in the domestic market and their features were described in detail. Finally, we described the steps that must be taken to select the most suitable ERP-system for a particular company.

  13. Business advertisements management system

    OpenAIRE

    Rekel, Ernest

    2017-01-01

    Business Advertisements Management System The main goal of the project was to create a business advertisements management system, where users could easily create and find business advertisements. To accomplish this goal exist- ing systems were analyzed as well as their limitations. The end result is a working system which is able to store and proccess huge amount of data.

  14. Functional System Dynamics

    OpenAIRE

    Ligterink, N.E.

    2007-01-01

    Functional system dynamics is the analysis, modelling, and simulation of continuous systems usually described by partial differential equations. From the infinite degrees of freedom of such systems only a finite number of relevant variables have to be chosen for a practical model description. The proper input and output of the system are an important part of the relevant variables.

  15. Type Systems for Bigraphs

    DEFF Research Database (Denmark)

    Elsborg, Ebbe; Hildebrandt, Thomas; Sangiorgi, Davide

    of controls and a set of reaction rules, collectively a bigraphical reactive system (BRS). Possible advantages of developing bigraphical type systems include: a deeper understanding of a type system itself and its properties; transfer of the type systems to the concrete family of calculi that the BRS models...

  16. Computer Operating System Maintenance.

    Science.gov (United States)

    1982-06-01

    FACILITY The Computer Management Information Facility ( CMIF ) system was developed by Rapp Systems to fulfill the need at the CRF to record and report on...computer center resource usage and utilization. The foundation of the CMIF system is a System 2000 data base (CRFMGMT) which stores and permits access

  17. Balancing for nonlinear systems

    NARCIS (Netherlands)

    Scherpen, J.M.A.

    1993-01-01

    We present a method of balancing for nonlinear systems which is an extension of balancing for linear systems in the sense that it is based on the input and output energy of a system. It is a local result, but gives 'broader' results than we obtain by just linearizing the system. Furthermore, the

  18. EPICS system: system structure and user interface

    International Nuclear Information System (INIS)

    West, R.E.; Bartlett, J.F.; Bobbitt, J.S.; Lahey, T.E.; Kramper, B.J.; MacKinnon, B.A.

    1984-02-01

    This paper present the user's view of and the general organization of the EPICS control system at Fermilab. Various subsystems of the EPICS control system are discussed. These include the user command language, software protection, the device database, remote computer interfaces, and several application utilities. This paper is related to two other papers on EPICS: an overview paper and a detailed implementation paper

  19. Probabilistic fuzzy systems as additive fuzzy systems

    NARCIS (Netherlands)

    Almeida, R.J.; Verbeek, N.; Kaymak, U.; Costa Sousa, da J.M.; Laurent, A.; Strauss, O.; Bouchon-Meunier, B.; Yager, R.

    2014-01-01

    Probabilistic fuzzy systems combine a linguistic description of the system behaviour with statistical properties of data. It was originally derived based on Zadeh’s concept of probability of a fuzzy event. Two possible and equivalent additive reasoning schemes were proposed, that lead to the

  20. System of Systems Analytic Workbench - 2017

    Science.gov (United States)

    2017-08-31

    Genetic Algorithm and Particle Swarm Optimization with Type-2 Fuzzy Sets for Generating Systems of Systems Architectures. Procedia Computer Science...The application effort involves modeling an existing messaging network to perform real-time situational awareness. The Analytical Workbench’s

  1. On generalized Volterra systems

    Science.gov (United States)

    Charalambides, S. A.; Damianou, P. A.; Evripidou, C. A.

    2015-01-01

    We construct a large family of evidently integrable Hamiltonian systems which are generalizations of the KM system. The algorithm uses the root system of a complex simple Lie algebra. The Hamiltonian vector field is homogeneous cubic but in a number of cases a simple change of variables transforms such a system to a quadratic Lotka-Volterra system. We present in detail all such systems in the cases of A3, A4 and we also give some examples from higher dimensions. We classify all possible Lotka-Volterra systems that arise via this algorithm in the An case.

  2. Transdisciplinarity Needs Systemism

    Directory of Open Access Journals (Sweden)

    Wolfgang Hofkirchner

    2017-02-01

    Full Text Available The main message of this paper is that systemism is best suited for transdisciplinary studies. A description of disciplinary sciences, transdisciplinary sciences and systems sciences is given, along with their different definitions of aims, scope and tools. The rationale for transdisciplinarity is global challenges, which are complex. The rationale for systemism is the concretization of understanding complexity. Drawing upon Ludwig von Bertalanffy’s intention of a General System Theory, three items deserve attention—the world-view of a synergistic systems technology, the world picture of an emergentist systems theory, and the way of thinking of an integrationist systems method.

  3. Measuring Systemic Risk

    DEFF Research Database (Denmark)

    Acharya, Viral V.; Heje Pedersen, Lasse; Philippon, Thomas

    2017-01-01

    We present an economic model of systemic risk in which undercapitalization of the financial sector as a whole is assumed to harm the real economy, leading to a systemic risk externality. Each financial institution’s contribution to systemic risk can be measured as its systemic expected shortfall...... of components of SES to predict emerging systemic risk during the financial crisis of 2007–2009....

  4. Multiprocessor data acquisition system

    International Nuclear Information System (INIS)

    Haumann, J.R.; Crawford, R.K.

    1987-01-01

    A multiprocessor data acquisition system has been built to replace the single processor systems at the Intense Pulsed Neutron Source (IPNS) at Argonne National Laboratory. The multiprocessor system was needed to accommodate the higher data rates at IPNS brought about by improvements in the source and changes in instrument configurations. This paper describes the hardware configuration of the system and the method of task sharing and compares results to the single processor system

  5. Genetics, systems, and alcohol.

    Science.gov (United States)

    McClearn, G E

    1993-03-01

    Under a variety of rubrics (e.g., complexity, self-constructing systems, dissipative structures), interest has recently burgeoned in applying principles of complex systems to a wide variety of scientific issues. A major concern is with emergent properties of systems not derivable from the properties of components of the systems. In this paper, some elementary aspects of "systems" considerations are applied to phenomena of alcohol pharmacogenetics. It is likely that whole new families of informative phenotypes can be generated by this approach.

  6. Intrusion detection system elements

    International Nuclear Information System (INIS)

    Eaton, M.J.; Mangan, D.L.

    1980-09-01

    This report highlights elements required for an intrusion detection system and discusses problems which can be encountered in attempting to make the elements effective. Topics discussed include: sensors, both for exterior detection and interior detection; alarm assessment systems, with the discussion focused on video assessment; and alarm reporting systems, including alarm communication systems and dislay/console considerations. Guidance on careful planning and design of a new or to-be-improved system is presented

  7. Satellite services system overview

    Science.gov (United States)

    Rysavy, G.

    1982-01-01

    The benefits of a satellite services system and the basic needs of the Space Transportation System to have improved satellite service capability are identified. Specific required servicing equipment are discussed in terms of their technology development status and their operative functions. Concepts include maneuverable television systems, extravehicular maneuvering unit, orbiter exterior lighting, satellite holding and positioning aid, fluid transfer equipment, end effectors for the remote manipulator system, teleoperator maneuvering system, and hand and power tools.

  8. HYBRID VEHICLE CONTROL SYSTEM

    Directory of Open Access Journals (Sweden)

    V. Dvadnenko

    2016-06-01

    Full Text Available The hybrid vehicle control system includes a start–stop system for an internal combustion engine. The system works in a hybrid mode and normal vehicle operation. To simplify the start–stop system, there were user new possibilities of a hybrid car, which appeared after the conversion. Results of the circuit design of the proposed system of basic blocks are analyzed.

  9. The control system

    International Nuclear Information System (INIS)

    1988-01-01

    The present control system has matured both in terms of age and capacity. Thus a new system based on a local area network (LAN) is being developed. A pilot project has been started but, owing to difficulties encountered with the present operating system used with the microprocessors, it has become necessary to reconsider the choice of operating system. A recently-released multi-tasking operating system that runs on the existing hardware has been chosen. 1 fig

  10. SQL injection detection system

    OpenAIRE

    Vargonas, Vytautas

    2017-01-01

    SQL injection detection system Programmers do not always ensure security of developed systems. That is why it is important to look for solutions outside being reliant on developers. In this work SQL injection detection system is proposed. The system analyzes HTTP request parameters and detects intrusions. It is based on unsupervised machine learning. Trained by regular request data system detects outlier user parameters. Since training is not reliant on previous knowledge of SQL injections, t...

  11. Evolvable synthetic neural system

    Science.gov (United States)

    Curtis, Steven A. (Inventor)

    2009-01-01

    An evolvable synthetic neural system includes an evolvable neural interface operably coupled to at least one neural basis function. Each neural basis function includes an evolvable neural interface operably coupled to a heuristic neural system to perform high-level functions and an autonomic neural system to perform low-level functions. In some embodiments, the evolvable synthetic neural system is operably coupled to one or more evolvable synthetic neural systems in a hierarchy.

  12. Telemetry System Data Latency

    Science.gov (United States)

    2017-07-13

    latencies will be measured. DATS Network TM Antenna TM ReceiverMCS System IOPlex IOPlexIADS CDS IADS Client TM Transmitter Sensors Signal Conditioning...TIME Figure 1-2 Mission Control System (MCS) / Interactive Analysis and Display System (IADS) Overview IADS CDSIADS Client TELEMETRY SYSTEM DATA...Sim GPS Signal Combiner MCS system Oscilloscope IADS Client IADS CDS Figure 13-1 IADS Data Flow 13.2. Test Results The results of the data test at

  13. Systems Theory and Systems Approach to Leadership

    Directory of Open Access Journals (Sweden)

    Dr.Sc. Berim Ramosaj

    2014-06-01

    Full Text Available Systems theory is product of the efforts of many researchers to create an intermediate field of coexistence of all sciences. If not for anything else, because of the magnitude that the use of systemic thinking and systemic approach has taken, it has become undisputed among the theories. Systems theory not only provides a glossary of terms with which researchers from different fields can be understood, but provides a framework for the presentation and interpretation of phenomena and realities. This paper addresses a systematic approach to leadership, as an attempt to dredge leadership and systems theory literature to find the meeting point. Systems approach is not an approach to leadership in terms of a manner of leader’s work, but it’s the leader's determination to factorize in his leadership the external environment and relationships with and among elements. Leader without followers is unable to exercise his leadership and to ensure their conviction he should provide a system, a structure, a purpose, despite the alternative chaos. Systems approach clarifies the thought on the complexity and dynamism of the environment and provides a framework for building ideas. If the general system theory is the skeleton of science (Boulding: 1956, this article aims to replenish it with leadership muscles by prominent authors who have written on systems theory and leadership, as well as through original ideas. In this work analytical methods were used (by analyzing approaches individually as well as synthetic methods (by assaying individual approaches in context of entirety. The work is a critical review of literature as well as a deductive analysis mingled with models proposed by authors through inductive analysis. Meta-analysis has been used to dissect the interaction and interdependence between leadership approaches.

  14. A distribution management system

    Energy Technology Data Exchange (ETDEWEB)

    Verho, P.; Jaerventausta, P.; Kaerenlampi, M.; Paulasaari, H. [Tampere Univ. of Technology (Finland); Partanen, J. [Lappeenranta Univ. of Technology (Finland)

    1996-12-31

    The development of new distribution automation applications is considerably wide nowadays. One of the most interesting areas is the development of a distribution management system (DMS) as an expansion of the traditional SCADA system. At the power transmission level such a system is called an energy management system (EMS). The idea of these expansions is to provide supporting tools for control center operators in system analysis and operation planning. The needed data for new applications is mainly available in some existing systems. Thus the computer systems of utilities must be integrated. The main data source for the new applications in the control center are the AM/FM/GIS (i.e. the network database system), the SCADA, and the customer information system (CIS). The new functions can be embedded in some existing computer system. This means a strong dependency on the vendor of the existing system. An alternative strategy is to develop an independent system which is integrated with other computer systems using well-defined interfaces. The latter approach makes it possible to use the new applications in various computer environments, having only a weak dependency on the vendors of the other systems. In the research project this alternative is preferred and used in developing an independent distribution management system

  15. A distribution management system

    Energy Technology Data Exchange (ETDEWEB)

    Verho, P; Jaerventausta, P; Kaerenlampi, M; Paulasaari, H [Tampere Univ. of Technology (Finland); Partanen, J [Lappeenranta Univ. of Technology (Finland)

    1997-12-31

    The development of new distribution automation applications is considerably wide nowadays. One of the most interesting areas is the development of a distribution management system (DMS) as an expansion of the traditional SCADA system. At the power transmission level such a system is called an energy management system (EMS). The idea of these expansions is to provide supporting tools for control center operators in system analysis and operation planning. The needed data for new applications is mainly available in some existing systems. Thus the computer systems of utilities must be integrated. The main data source for the new applications in the control center are the AM/FM/GIS (i.e. the network database system), the SCADA, and the customer information system (CIS). The new functions can be embedded in some existing computer system. This means a strong dependency on the vendor of the existing system. An alternative strategy is to develop an independent system which is integrated with other computer systems using well-defined interfaces. The latter approach makes it possible to use the new applications in various computer environments, having only a weak dependency on the vendors of the other systems. In the research project this alternative is preferred and used in developing an independent distribution management system

  16. Modeling Power Systems as Complex Adaptive Systems

    Energy Technology Data Exchange (ETDEWEB)

    Chassin, David P.; Malard, Joel M.; Posse, Christian; Gangopadhyaya, Asim; Lu, Ning; Katipamula, Srinivas; Mallow, J V.

    2004-12-30

    Physical analogs have shown considerable promise for understanding the behavior of complex adaptive systems, including macroeconomics, biological systems, social networks, and electric power markets. Many of today's most challenging technical and policy questions can be reduced to a distributed economic control problem. Indeed, economically based control of large-scale systems is founded on the conjecture that the price-based regulation (e.g., auctions, markets) results in an optimal allocation of resources and emergent optimal system control. This report explores the state-of-the-art physical analogs for understanding the behavior of some econophysical systems and deriving stable and robust control strategies for using them. We review and discuss applications of some analytic methods based on a thermodynamic metaphor, according to which the interplay between system entropy and conservation laws gives rise to intuitive and governing global properties of complex systems that cannot be otherwise understood. We apply these methods to the question of how power markets can be expected to behave under a variety of conditions.

  17. Rover waste assay system

    Energy Technology Data Exchange (ETDEWEB)

    Akers, D.W.; Stoots, C.M.; Kraft, N.C.; Marts, D.J. [Idaho National Engineering Lab., Idaho Falls, ID (United States)

    1997-11-01

    The Rover Waste Assay System (RWAS) is a nondestructive assay system designed for the rapid assay of highly-enriched {sup 235}U contaminated piping, tank sections, and debris from the Rover nuclear rocket fuel processing facility at the Idaho Chemical Processing Plant. A scanning system translates a NaI(Tl) detector/collimator system over the structural components where both relative and calibrated measurements for {sup 137}Cs are made. Uranium-235 concentrations are in operation and is sufficiently automated that most functions are performed by the computer system. These functions include system calibration, problem identification, collimator control, data analysis, and reporting. Calibration of the system was done through a combination of measurements on calibration standards and benchmarked modeling. A description of the system is presented along with the methods and uncertainties associated with the calibration and analysis of the system for components from the Rover facility. 4 refs., 2 figs., 4 tabs.

  18. Rover waste assay system

    International Nuclear Information System (INIS)

    Akers, D.W.; Stoots, C.M.; Kraft, N.C.; Marts, D.J.

    1997-01-01

    The Rover Waste Assay System (RWAS) is a nondestructive assay system designed for the rapid assay of highly-enriched 235 U contaminated piping, tank sections, and debris from the Rover nuclear rocket fuel processing facility at the Idaho Chemical Processing Plant. A scanning system translates a NaI(Tl) detector/collimator system over the structural components where both relative and calibrated measurements for 137 Cs are made. Uranium-235 concentrations are in operation and is sufficiently automated that most functions are performed by the computer system. These functions include system calibration, problem identification, collimator control, data analysis, and reporting. Calibration of the system was done through a combination of measurements on calibration standards and benchmarked modeling. A description of the system is presented along with the methods and uncertainties associated with the calibration and analysis of the system for components from the Rover facility. 4 refs., 2 figs., 4 tabs

  19. Micro Information Systems

    DEFF Research Database (Denmark)

    Ulslev Pedersen, Rasmus; Kühn Pedersen, Mogens

    2014-01-01

    such as medical and manufacturing. These new sensor applications have implications for information systems (IS) and, the authors visualize this new class of information systems as fractals growing from an established class of systems; namely that of information systems (IS). The identified applications...... and implications are used as an empirical basis for creating a model for these small new information systems. Such sensor systems are called embedded systems in the technical sciences, and the authors want to couple it with general IS. They call the merger of these two important research areas (IS and embedded...... systems) for micro information systems (micro-IS). It is intended as a new research field within IS research. An initial framework model is established, which seeks to capture both the possibilities and constraints of this new paradigm, while looking simultaneously at the fundamental IS and ICT aspects...

  20. ITER cooling systems

    International Nuclear Information System (INIS)

    Natalizio, A.; Hollies, R.E.; Sochaski, R.O.; Stubley, P.H.

    1992-06-01

    The ITER reference system uses low-temperature water for heat removal and high-temperature helium for bake-out. As these systems share common equipment, bake-out cannot be performed until the cooling system is drained and dried, and the reactor cannot be started until the helium has been purged from the cooling system. This study examines the feasibility of using a single high-temperature fluid to perform both heat removal and bake-out. The high temperature required for bake-out would also be in the range for power production. The study examines cost, operational benefits, and impact on reactor safety of two options: a high-pressure water system, and a low-pressure organic system. It was concluded that the cost savings and operational benefits are significant; there are no significant adverse safety impacts from operating either the water system or the organic system; and the capital costs of both systems are comparable

  1. System performance optimization

    International Nuclear Information System (INIS)

    Bednarz, R.J.

    1978-01-01

    The System Performance Optimization has become an important and difficult field for large scientific computer centres. Important because the centres must satisfy increasing user demands at the lowest possible cost. Difficult because the System Performance Optimization requires a deep understanding of hardware, software and workload. The optimization is a dynamic process depending on the changes in hardware configuration, current level of the operating system and user generated workload. With the increasing complication of the computer system and software, the field for the optimization manoeuvres broadens. The hardware of two manufacturers IBM and CDC is discussed. Four IBM and two CDC operating systems are described. The description concentrates on the organization of the operating systems, the job scheduling and I/O handling. The performance definitions, workload specification and tools for the system stimulation are given. The measurement tools for the System Performance Optimization are described. The results of the measurement and various methods used for the operating system tuning are discussed. (Auth.)

  2. NASA systems engineering handbook

    Science.gov (United States)

    Shishko, Robert; Aster, Robert; Chamberlain, Robert G.; McDuffee, Patrick; Pieniazek, Les; Rowell, Tom; Bain, Beth; Cox, Renee I.; Mooz, Harold; Polaski, Lou

    1995-06-01

    This handbook brings the fundamental concepts and techniques of systems engineering to NASA personnel in a way that recognizes the nature of NASA systems and environment. It is intended to accompany formal NASA training courses on systems engineering and project management when appropriate, and is designed to be a top-level overview. The concepts were drawn from NASA field center handbooks, NMI's/NHB's, the work of the NASA-wide Systems Engineering Working Group and the Systems Engineering Process Improvement Task team, several non-NASA textbooks and guides, and material from independent systems engineering courses taught to NASA personnel. Five core chapters cover systems engineering fundamentals, the NASA Project Cycle, management issues in systems engineering, systems analysis and modeling, and specialty engineering integration. It is not intended as a directive.

  3. Expert systems and computer based industrial systems

    International Nuclear Information System (INIS)

    Dunand, R.

    1989-01-01

    Framentec is the artificial intelligence subsidiary of FRAMATOME. It is involved in expert-system activities of Shells, developments, methodology and software for maintenance (Maintex) and consulting and methodology. Specific applications in the nuclear field are presented. The first is an expert system to assist in the piping support design prototype, the second is an expert system that assists an ultrasonic testing operator in determining the nature of a welding defect and the third is a welding machine diagnosis advisor. Maintex is a software tool to provide assistance in the repair of complex industrial equipment. (author)

  4. Visualization System for Monitoring Data Management Systems

    Directory of Open Access Journals (Sweden)

    Emanuel Pinho

    2016-11-01

    Full Text Available Usually, a Big Data system has a monitoring system for performance evaluation and error prevention. There are some disadvantages in the way that these tools display the information and its targeted approach to physical components. The main goal is to study visual and interactive mechanisms that allow the representation of monitoring data in grid computing environments, providing the end-user information, which can contribute objectively to the system analysis. This paper is an extension of the paper presented at (Pinho and Carvalho 2016 and has the purpose to present the state of the art, carries out the proposed solution and present the achieved goals.

  5. System architecture for microprocessor based protection system

    International Nuclear Information System (INIS)

    Gallagher, J.M. Jr.; Lilly, G.M.

    1976-01-01

    This paper discusses the architectural design features to be employed by Westinghouse in the application of distributed digital processing techniques to the protection system. While the title of the paper makes specific reference to microprocessors, this is only one (and the newest) of the building blocks which constitutes a distributed digital processing system. The actual system structure (as realized through utilization of the various building blocks) is established through considerations of reliability, licensability, and cost. It is the intent of the paper to address these considerations licenstions as they relate to the architectural design features. (orig.) [de

  6. Embedded systems handbook networked embedded systems

    CERN Document Server

    Zurawski, Richard

    2009-01-01

    Considered a standard industry resource, the Embedded Systems Handbook provided researchers and technicians with the authoritative information needed to launch a wealth of diverse applications, including those in automotive electronics, industrial automated systems, and building automation and control. Now a new resource is required to report on current developments and provide a technical reference for those looking to move the field forward yet again. Divided into two volumes to accommodate this growth, the Embedded Systems Handbook, Second Edition presents a comprehensive view on this area

  7. Modern system architectures in embedded systems

    International Nuclear Information System (INIS)

    Korhonen, T.

    2012-01-01

    Several new technologies are making their way also in embedded systems. In addition to the FPGA technology which has become commonplace, multi-core CPUs and I/O virtualization (the implementation of the tasks of a software hyper-visor in hardware to improve the efficiency) are being introduced to the embedded systems. In this paper we review the trends and discuss how to take advantage of these features in control systems. Some potential application examples like parallelization, data streaming, high-speed data acquisition and virtualization are discussed

  8. Nonlinearity of colloid systems oxyhydrate systems

    CERN Document Server

    Sucharev, Yuri I

    2008-01-01

    The present monograph is the first systematic study of the non-linear characteristic of gel oxy-hydrate systems involving d- and f- elements. These are the oxyhydrates of rare-earth elements and oxides - hydroxides of d- elements (zirconium, niobium, titanium, etc.) The non-linearity of these gel systems introduces fundamental peculiarities into their structure and, consequently, their properties. The polymer-conformational diversity of energetically congenial gel fragments, which continu-ously transform under the effect of, for instance, system dissipation heat, is central to the au-thor's hy

  9. Information system development activities and inquiring systems

    DEFF Research Database (Denmark)

    Carugati, Andrea

    2008-01-01

    This article presents a framework that maps information system development (ISD) activities on systems for the creation of knowledge. This work addresses the relevant and persisting problem of improving the chances of ISD success. The article builds upon previous research on knowledge aspects...... based on ISD literature and on Churchman's (1971) inquiring systems. The second part presents the use of the framework in an ISD project. The case is used to show the applicability of the framework and to highlight the advantages of this approach. The main theoretical implication is that the framework...

  10. Automatic remote communication system

    International Nuclear Information System (INIS)

    Yamamoto, Yoichi

    1990-05-01

    The Upgraded RECOVER (Remote Continual Verification) system is a communication system for remote continual verification of security and safeguards status of nuclear material in principal nuclear facilities. The system is composed of a command center and facility sub-systems. A command center is a mini-computer system to process C/S (Containment and Surveillance) status data. Facility sub-systems consists of OSM (On-site Multiplexer), MU (Monitoring Unit) and C/S sensor. The system uses public telephone network for communication between a command center and facility sub-systems, and it encrypts communication data to prevent falsification and wiretapping by unauthorized persons. This system inherits the design principle of RECOVER system that was tested by IAEA before. We upgraded and expanded its capabilities more than those of RECOVER. The development of this system began in 1983, and it finished in 1987. Performance tests of the system were carried out since 1987. It showed a farely good result with some indications which should need further improvements. The Upgraded RECOVER system provides timely information about the status of C/S systems, which could contribute to the reduction of inspection effort and the improvement of cost performance. (author)

  11. Photovoltaic systems engineering

    CERN Document Server

    Messenger, Roger A

    2010-01-01

    BackgroundPopulation and Energy DemandEnergy UnitsCurrent World Energy Use PatternsExponential GrowthHubbert's Gaussian ModelNet Energy, Btu Economics, and the Test for SustainabilityDirect Conversion of Sunlight to Electricity with PhotovoltaicsThe SunThe Solar SpectrumThe Effect of Atmosphere on SunlightSunlight SpecificsCapturing SunlightIntroduction to PV SystemsThe PV CellThe PV ModuleThe PV ArrayEnergy StoragePV System LoadsPV System AvailabilityAssociated System Electronic ComponentsGeneratorsBalance of System (BOS) ComponentsGrid-Connected Utility-Interactive PV SystemsApplicable Codes and StandardsDesign Considerations for Straight Grid-Connected PV SystemsDesign of a System Based on Desired Annual System PerformanceDesign of a System Based on Available Roof SpaceDesign of a Microinverter-Based SystemDesign of a Nominal 21 kW System that Feeds a Three-Phase Distribution PanelDesign of a Nominal 250 kW SystemSystem Performance MonitoringMechanical ConsiderationsImportant Properties of MaterialsEstabli...

  12. T-systems and Y-systems in integrable systems

    International Nuclear Information System (INIS)

    Kuniba, Atsuo; Nakanishi, Tomoki; Suzuki, Junji

    2011-01-01

    T- and Y-systems are ubiquitous structures in classical and quantum integrable systems. They are difference equations having a variety of aspects related to commuting transfer matrices in solvable lattice models, q-characters of Kirillov-Reshetikhin modules of quantum affine algebras, cluster algebras with coefficients, periodicity conjectures of Zamolodchikov and others, dilogarithm identities in conformal field theory, difference analog of L-operators in KP hierarchy, Stokes phenomena in 1D Schroedinger problem, AdS/CFT correspondence, Toda field equations on discrete spacetime, Laplace sequence in discrete geometry, Fermionic character formulas and combinatorial completeness of Bethe ansatz, Q-system and ideal gas with exclusion statistics, analytic and thermodynamic Bethe ansaetze, quantum transfer matrix method and so forth. This review is a collection of short reviews on these topics which can be read more or less independently. (topical review)

  13. T-systems and Y-systems in integrable systems

    Energy Technology Data Exchange (ETDEWEB)

    Kuniba, Atsuo [Institute of Physics, University of Tokyo, Komaba, Tokyo 153-8902 (Japan); Nakanishi, Tomoki [Graduate School of Mathematics, Nagoya University, Nagoya 464-8604 (Japan); Suzuki, Junji, E-mail: atsuo@gokutan.c.u-tokyo.ac.jp [Department of Physics, Faculty of Science, Shizuoka University, Ohya 836 (Japan)

    2011-03-11

    T- and Y-systems are ubiquitous structures in classical and quantum integrable systems. They are difference equations having a variety of aspects related to commuting transfer matrices in solvable lattice models, q-characters of Kirillov-Reshetikhin modules of quantum affine algebras, cluster algebras with coefficients, periodicity conjectures of Zamolodchikov and others, dilogarithm identities in conformal field theory, difference analog of L-operators in KP hierarchy, Stokes phenomena in 1D Schroedinger problem, AdS/CFT correspondence, Toda field equations on discrete spacetime, Laplace sequence in discrete geometry, Fermionic character formulas and combinatorial completeness of Bethe ansatz, Q-system and ideal gas with exclusion statistics, analytic and thermodynamic Bethe ansaetze, quantum transfer matrix method and so forth. This review is a collection of short reviews on these topics which can be read more or less independently. (topical review)

  14. Cooperating systems: Layered MAS

    Science.gov (United States)

    Rochowiak, Daniel

    1990-01-01

    Distributed intelligent systems can be distinguished by the models that they use. The model developed focuses on layered multiagent system conceived of as a bureaucracy in which a distributed data base serves as a central means of communication. The various generic bureaus of such a system is described and a basic vocabulary for such systems is presented. In presenting the bureaus and vocabularies, special attention is given to the sorts of reasonings that are appropriate. A bureaucratic model has a hierarchy of master system and work group that organizes E agents and B agents. The master system provides the administrative services and support facilities for the work groups.

  15. Simulation of Polygeneration Systems

    Directory of Open Access Journals (Sweden)

    Francesco Calise

    2016-11-01

    Full Text Available This Special Issue aims at collecting the recent studies dealing with polygeneration systems, with a special focus on the possible integration of different technologies into a single system, able to convert one or multiple energy sources into energy services (electricity, heat and cooling and other useful products (e.g., desalinized water, hydrogen, glycerin, ammonia, etc.. Renewable sources (solar, wind, hydro, biomass and geothermal, as well as fossil fuels, feeding advanced energy systems such as fuel cells and cogeneration systems, are considered. Special attention is paid to control strategies and to the management of the systems in general. Studies including thermoeconomic analyses and system optimizations are presented.

  16. The BELLE DAQ system

    Science.gov (United States)

    Suzuki, Soh Yamagata; Yamauchi, Masanori; Nakao, Mikihiko; Itoh, Ryosuke; Fujii, Hirofumi

    2000-10-01

    We built a data acquisition system for the BELLE experiment. The system was designed to cope with the average trigger rate up to 500 Hz at the typical event size of 30 kB. This system has five components: (1) the readout sequence controller, (2) the FASTBUS-TDC readout systems using charge-to-time conversion, (3) the barrel shifter event builder, (4) the parallel online computing farm, and (5) the data transfer system to the mass storage. This system has been in operation for physics data taking since June 1999 without serious problems.

  17. The BELLE DAQ system

    International Nuclear Information System (INIS)

    Suzuki, Soh Yamagata; Yamauchi, Masanori; Nakao, Mikihiko; Itoh, Ryosuke; Fujii, Hirofumi

    2000-01-01

    We built a data acquisition system for the BELLE experiment. The system was designed to cope with the average trigger rate up to 500 Hz at the typical event size of 30 kB. This system has five components: (1) the readout sequence controller, (2) the FASTBUS-TDC readout systems using charge-to-time conversion, (3) the barrel shifter event builder, (4) the parallel online computing farm, and (5) the data transfer system to the mass storage. This system has been in operation for physics data taking since June 1999 without serious problems

  18. Reliable computer systems.

    Science.gov (United States)

    Wear, L L; Pinkert, J R

    1993-11-01

    In this article, we looked at some decisions that apply to the design of reliable computer systems. We began with a discussion of several terms such as testability, then described some systems that call for highly reliable hardware and software. The article concluded with a discussion of methods that can be used to achieve higher reliability in computer systems. Reliability and fault tolerance in computers probably will continue to grow in importance. As more and more systems are computerized, people will want assurances about the reliability of these systems, and their ability to work properly even when sub-systems fail.

  19. Adaptive intrusion data system

    International Nuclear Information System (INIS)

    Johnson, C.S.

    1976-01-01

    An Adaptive Intrusion Data System (AIDS) was developed to collect data from intrusion alarm sensors as part of an evaluation system to improve sensor performance. AIDS is a unique digital data compression, storage, and formatting system. It also incorporates capability for video selection and recording for assessment of the sensors monitored by the system. The system is software reprogrammable to numerous configurations that may be utilized for the collection of environmental, bi-level, analog and video data. The output of the system is digital tapes formatted for direct data reduction on a CDC 6400 computer, and video tapes containing timed tagged information that can be correlated with the digital data

  20. Introducing Systems Approaches

    Science.gov (United States)

    Reynolds, Martin; Holwell, Sue

    Systems Approaches to Managing Change brings together five systems approaches to managing complex issues, each having a proven track record of over 25 years. The five approaches are: System Dynamics (SD) developed originally in the late 1950s by Jay Forrester Viable Systems Model (VSM) developed originally in the late 1960s by Stafford Beer Strategic Options Development and Analysis (SODA: with cognitive mapping) developed originally in the 1970s by Colin Eden Soft Systems Methodology (SSM) developed originally in the 1970s by Peter Checkland Critical Systems Heuristics (CSH) developed originally in the late 1970s by Werner Ulrich

  1. EPICS system: an overview

    International Nuclear Information System (INIS)

    Bartlett, J.F.; Bobbitt, J.S.; Kramper, B.J.; Lahey, T.E.; MacKinnon, B.A.; West, R.E.

    1984-02-01

    This paper presents an overview of the EPICS control system at FERMILAB. EPICS is a distributed, multi-user, interactive system for the control and monitoring of particle beamlines at a high-energy experimental physics laboratory. The overview discusses the operating environment of the control system, the requirements which determined the design decisions, the hardware and software configurations, and plans for the future growth and enhancement of the present system. This paper is the first of three related papers on the EPICS system. The other two cover (1) the system structure and user interface and (2) RSX implementation issues

  2. Nonlinear Hamiltonian systems

    DEFF Research Database (Denmark)

    Jørgensen, Michael Finn

    1995-01-01

    It is generally very difficult to solve nonlinear systems, and such systems often possess chaotic solutions. In the rare event that a system is completely solvable, it is said to integrable. Such systems never have chaotic solutions. Using the Inverse Scattering Transform Method (ISTM) two...... particular configurations of the Discrete Self-Trapping (DST) system are shown to be completely solvable. One of these systems includes the Toda lattice in a certain limit. An explicit integration is carried through for this Near-Toda lattice. The Near-Toda lattice is then generalized to include singular...

  3. LCA of Energy Systems

    DEFF Research Database (Denmark)

    Laurent, Alexis; Espinosa Martinez, Nieves; Hauschild, Michael Zwicky

    2018-01-01

    Energy systems are essential in the support of modern societies’ activities, and can span a wide spectrum of electricity and heat generation systems and cooling systems. Along with their central role and large diversity, these systems have been demonstrated to cause serious impacts on human health...... , ecosystems and natural resources. Over the past two decades, energy systems have thus been the focus of more than 1000 LCA studies, with the aim to identify and reduce these impacts. This chapter addresses LCA applications to energy systems for generation of electricity and heat . The chapter gives insight...

  4. Two Tethered Balloon Systems

    Science.gov (United States)

    Youngbluth, Otto; Owens, Thomas L.; Storey, Richard W.

    1990-01-01

    Systems take meteorological measurements for variety of research projects. Report describes work done by NASA Langley Research Center in atmospheric research using tethered balloon systems composed of commercially available equipment. Two separate tethered balloon systems described in report have payloads and configurations tailored to requirements of specific projects. Each system capable of measuring atmospheric parameter or species in situ and then telemetering this data in real time to ground station. Meteorological data and concentration of ozone typically measured. Indicates instrumented tethered balloon systems have distinct advantages over other systems for gathering data on troposphere.

  5. Microelectronic systems 1 checkbook

    CERN Document Server

    Vears, R E

    2013-01-01

    Microelectronic Systems 1 Checkbook provides coverage of the Business and Technician Education Council level 1 unit in Microelectronic Systems. However, it can be regarded as a basic textbook in microelectronic systems for a much wider range of studies. Each topic considered in the text is presented in a way that assumes the reader has little prior knowledge of electronics. The aim of the book is to provide an introduction to the concept of systems, to differentiate analogue and digital systems, and to describe the nature of microprocessor-controlled systems. An introduction to programming is

  6. Quality data systems

    International Nuclear Information System (INIS)

    Bergman, J.E.; Patterson, R.G.

    1976-01-01

    General Electric's Nuclear Fuel Department data system strategy of multifunctional system integration and specific applications of data systems for the Quality Assurance Programme is detailed. Descriptions of two manufacturing control systems and their function in satisfying quality data requirements are included. The timesharing quality data system developed for processing laboratory, traceability and material release data in the Fuel Manufacturing Operation is described. In addition, specific references are made to those areas where significant time reductions have been realized through the utilization of mechanized data-handling systems. (author)

  7. Water Fluoridation Reporting System (Public Water Systems)

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Water Fluoridation Reporting System (WFRS) has been developed to provide tools to assist states in managing fluoridation programs. WFRS is designed to track all...

  8. Combat Systems Department Employee Recognition System

    National Research Council Canada - National Science Library

    1996-01-01

    This handbook contains two types of information: guidelines and instructions. The guidelines provide a foundation of purpose, assumptions, principles, expectations and attributes the Employee Recognition System is designed to reflect...

  9. Test System Impact on System Availability

    DEFF Research Database (Denmark)

    Pau, L. F.

    1987-01-01

    The specifications are presented for an imperfect automatic test system (ATS) (test frequency distribution, reliability, false alarm rate, nondetection rate) in order to account for the availability, readiness, mean time between unscheduled repairs (MTBUR), reliability, and maintenance of the sys......The specifications are presented for an imperfect automatic test system (ATS) (test frequency distribution, reliability, false alarm rate, nondetection rate) in order to account for the availability, readiness, mean time between unscheduled repairs (MTBUR), reliability, and maintenance...... of the system subject to monitoring and test. A time-dependent Markov model is presented, and applied in three cases, with examples of numerical results provided for preventive maintenance decisions, design of an automatic test system, buffer testing in computers, and data communications....

  10. An expert system for reward systems design.

    OpenAIRE

    Erturk, Alper

    2000-01-01

    Approved for public release; distribution is unlimited Today's business environment is a highly competitive marketplace. In this competition, organizations distribute numerous rewards to motivate, attract and retain employees, such as pay, fringe benefits and promotions. However, not all managers have the necessary knowledge and expertise to effectively decide and structure reward systems. This thesis presents an expert system to assist managers with designing the most appropriate reward s...

  11. SUBSURFACE EMPLACEMENT TRANSPORTATION SYSTEM

    International Nuclear Information System (INIS)

    Wilson, T.; Novotny, R.

    1999-01-01

    The objective of this analysis is to identify issues and criteria that apply to the design of the Subsurface Emplacement Transportation System (SET). The SET consists of the track used by the waste package handling equipment, the conductors and related equipment used to supply electrical power to that equipment, and the instrumentation and controls used to monitor and operate those track and power supply systems. Major considerations of this analysis include: (1) Operational life of the SET; (2) Geometric constraints on the track layout; (3) Operating loads on the track; (4) Environmentally induced loads on the track; (5) Power supply (electrification) requirements; and (6) Instrumentation and control requirements. This analysis will provide the basis for development of the system description document (SDD) for the SET. This analysis also defines the interfaces that need to be considered in the design of the SET. These interfaces include, but are not limited to, the following: (1) Waste handling building; (2) Monitored Geologic Repository (MGR) surface site layout; (3) Waste Emplacement System (WES); (4) Waste Retrieval System (WRS); (5) Ground Control System (GCS); (6) Ex-Container System (XCS); (7) Subsurface Electrical Distribution System (SED); (8) MGR Operations Monitoring and Control System (OMC); (9) Subsurface Facility System (SFS); (10) Subsurface Fire Protection System (SFR); (11) Performance Confirmation Emplacement Drift Monitoring System (PCM); and (12) Backfill Emplacement System (BES)

  12. Solar power satellite system; Uchu hatsuden system

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, S [Institute of Space and Astronautical Science, Tokyo (Japan)

    1995-09-05

    The solar power satellite system is a system that converts solar energy into electric energy in the space, transmits power to earth through wireless resort such as microwave and supplies energy of new concept. In order to realize this system it is necessary to have new technologies such as space power transmission at low cost, construction of large space buildings and wireless high power transmission. In this paper, the principles, characteristics and the necessary technology of this system were explained. Besides Japan`s SPS2000 Plan (cooperative research by universities, government agencies and private corporations on the model of solar power satellite) the group of Europe, Russia and the United States has also proposed some ideas concerning the solar power satellite system. As far as the microwave power transmission, which is the key technology for solar power satellite system, is concerned, ground demonstration tests at the level of several tens of kW are discussed in Canada and France. 3 refs., 3 figs.

  13. System and method for creating expert systems

    Science.gov (United States)

    Hughes, Peter M. (Inventor); Luczak, Edward C. (Inventor)

    1998-01-01

    A system and method provides for the creation of a highly graphical expert system without the need for programming in code. An expert system is created by initially building a data interface, defining appropriate Mission, User-Defined, Inferred, and externally-generated GenSAA (EGG) data variables whose data values will be updated and input into the expert system. Next, rules of the expert system are created by building appropriate conditions of the rules which must be satisfied and then by building appropriate actions of rules which are to be executed upon corresponding conditions being satisfied. Finally, an appropriate user interface is built which can be highly graphical in nature and which can include appropriate message display and/or modification of display characteristics of a graphical display object, to visually alert a user of the expert system of varying data values, upon conditions of a created rule being satisfied. The data interface building, rule building, and user interface building are done in an efficient manner and can be created without the need for programming in code.

  14. Business system: Sustainable development and anticipatory system

    Directory of Open Access Journals (Sweden)

    Vojko Potočan

    2002-01-01

    Full Text Available The existence and development of humankind depends mainly upon the co-ordinated operation of all areas and levels of human activity. However, in theory and in practice there is no model of operation, which would provide a harmonized and target oriented development. A partial solution is offered by sustainable development, which tries to define and carry out common goals of mankind with a harmonized implementation of human activities at all levels of its living and behaviour. Companies belong to central institutions of modern society which essentially co–create the sustainability of society. The company’s endeavour by simulation to prepare models of their goals concerning their internal and external environment. On the base of systemic treatment, we can define companies as business system, which can survive in a log-run only on the basis of sustainable development. The business system can also be supported by the application of the anticipatory systems. The anticipatory systems can be, in this sense, understood as an entity of the methodological approach, techniques and modes of work. Their characteristics have, a direct impact on the determination of goals, on the orientation of operation, and hence on the achievement of the business system results.

  15. Operating System for Runtime Reconfigurable Multiprocessor Systems

    Directory of Open Access Journals (Sweden)

    Diana Göhringer

    2011-01-01

    Full Text Available Operating systems traditionally handle the task scheduling of one or more application instances on processor-like hardware architectures. RAMPSoC, a novel runtime adaptive multiprocessor System-on-Chip, exploits the dynamic reconfiguration on FPGAs to generate, start and terminate hardware and software tasks. The hardware tasks have to be transferred to the reconfigurable hardware via a configuration access port. The software tasks can be loaded into the local memory of the respective IP core either via the configuration access port or via the on-chip communication infrastructure (e.g. a Network-on-Chip. Recent-series of Xilinx FPGAs, such as Virtex-5, provide two Internal Configuration Access Ports, which cannot be accessed simultaneously. To prevent conflicts, the access to these ports as well as the hardware resource management needs to be controlled, e.g. by a special-purpose operating system running on an embedded processor. For that purpose and to handle the relations between temporally and spatially scheduled operations, the novel approach of an operating system is of high importance. This special purpose operating system, called CAP-OS (Configuration Access Port-Operating System, which will be presented in this paper, supports the clients using the configuration port with the services of priority-based access scheduling, hardware task mapping and resource management.

  16. FFTF gas processing systems

    International Nuclear Information System (INIS)

    Halverson, T.G.

    1977-01-01

    The design and operation of the two radioactive gas processing systems at the Fast Flux Test Facility (FFTF) exemplifies the concept that will be used in the first generation of Liquid Metal Fast Breeder Reactors (LMFBR's). The two systems, the Radioactive Argon Processing System (RAPS) and the Cell Atmosphere Processing System (CAPS), process the argon and nitrogen used in the FFTF for cover gas on liquid metal systems and as inert atmospheres in steel lined cells housing sodium equipment. The RAPS specifically processes the argon cover gas from the reactor coolant system, providing for decontamination and eventual reuse. The CAPS processes radioactive gasses from inerted cells and other liquid metal cover gas systems, providing for decontamination and ultimate discharge to the atmosphere. The cryogenic processing of waste gas by both systems is described

  17. Optical Airborne Tracker System

    Data.gov (United States)

    National Aeronautics and Space Administration — The Optical Airborne Tracker System (OATS) is an airborne dual-axis optical tracking system capable of pointing at any sky location or ground target.  The objectives...

  18. Absorption heat pump system

    Science.gov (United States)

    Grossman, G.

    1982-06-16

    The efficiency of an absorption heat pump system is improved by conducting liquid from a second stage evaporator thereof to an auxiliary heat exchanger positioned downstream of a primary heat exchanger in the desorber of the system.

  19. Immune System (For Parents)

    Science.gov (United States)

    ... of the Immune System Print en español El sistema inmunitario The immune system, which is made up ... of Use Notice of Nondiscrimination Visit the Nemours Web site. Note: All information on KidsHealth® is for ...

  20. Designing automatic resupply systems.

    Science.gov (United States)

    Harding, M L

    1999-02-01

    This article outlines the process for designing and implementing autoresupply systems. The planning process includes determination of goals and appropriate participation. Different types of autoresupply mechanisms include kanban, breadman, consignment, systems contracts, and direct shipping from an MRP schedule.

  1. Organizing Systemic Innovation

    NARCIS (Netherlands)

    F.P.H. Jaspers (Ferdinand)

    2009-01-01

    textabstractSystemic innovation refers to product development activities that involve the change of multiple interdependent components. Unlike autonomous innovation, which refers to components that change independently, systemic innovation is for many firms the norm rather than the exception. This

  2. FAA Directives System

    Science.gov (United States)

    1992-08-26

    Consistent with the Federal Aviation Administration's mission to foster a safe, : secure, and efficient aviation system is the need for an effective and efficient : process for communitcating policy and procedures. The FAA Directives System : provide...

  3. Geographical information systems

    DEFF Research Database (Denmark)

    Möller, Bernd

    2004-01-01

    The chapter gives an introduction to Geographical Information Systems (GIS) with particular focus on their application within environmental management.......The chapter gives an introduction to Geographical Information Systems (GIS) with particular focus on their application within environmental management....

  4. Septic Systems Case Studies

    Science.gov (United States)

    A collection of septic systems case studies to help community planners, elected officials, health department staff, state officials, and interested citizens explore alternatives for managing their decentralized wastewater treatment systems.

  5. Inductive Monitoring System (IMS)

    Data.gov (United States)

    National Aeronautics and Space Administration — IMS: Inductive Monitoring System The Inductive Monitoring System (IMS) is a tool that uses a data mining technique called clustering to extract models of normal...

  6. Visitor Registration System

    Data.gov (United States)

    US Agency for International Development — Visitor Registration System (VRS) streamlines visitor check-in and check-out process for expediting visitors into USAID. The system captures visitor information...

  7. Information retrieval system

    Science.gov (United States)

    Berg, R. F.; Holcomb, J. E.; Kelroy, E. A.; Levine, D. A.; Mee, C., III

    1970-01-01

    Generalized information storage and retrieval system capable of generating and maintaining a file, gathering statistics, sorting output, and generating final reports for output is reviewed. File generation and file maintenance programs written for the system are general purpose routines.

  8. Semiotic labelled deductive systems

    Energy Technology Data Exchange (ETDEWEB)

    Nossum, R.T. [Imperial College of Science, Technology and Medicine, London (United Kingdom)

    1996-12-31

    We review the class of Semiotic Models put forward by Pospelov, as well as the Labelled Deductive Systems developed by Gabbay, and construct an embedding of Semiotic Models into Labelled Deductive Systems.

  9. Integrated Reporting Information System -

    Data.gov (United States)

    Department of Transportation — The Integrated Reporting Information System (IRIS) is a flexible and scalable web-based system that supports post operational analysis and evaluation of the National...

  10. HVAC systems and equipment

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, S.T. (Linford Air and Refrigeration Company, Oakland, CA (US))

    1990-02-01

    The author discusses the section of the ASHRAE Standard 90.1-1989 which addresses HVAC systems and equipment. New features of HVAC systems mandatory general requirements are described. New prescriptive requirements are detailed.

  11. Integrated security system definition

    International Nuclear Information System (INIS)

    Campbell, G.K.; Hall, J.R. II

    1985-01-01

    The objectives of an integrated security system are to detect intruders and unauthorized activities with a high degree of reliability and the to deter and delay them until effective response/engagement can be accomplished. Definition of an effective integrated security system requires proper application of a system engineering methodology. This paper summarizes a methodology and describes its application to the problem of integrated security system definition. This process includes requirements identification and analysis, allocation of identified system requirements to the subsystem level and provides a basis for identification of synergistic subsystem elements and for synthesis into an integrated system. The paper discusses how this is accomplished, emphasizing at each step how system integration and subsystem synergism is considered. The paper concludes with the product of the process: implementation of an integrated security system

  12. Electrical railway transportation systems

    CERN Document Server

    Brenna, Morris; Zaninelli, Dario

    2018-01-01

    Allows the reader to deepen their understanding of various technologies for both fixed power supply installations of railway systems and for railway rolling stock. This book explores the electric railway systems that play a crucial role in the mitigation of congestion and pollution caused by road traffic. It is divided into two parts: the first covering fixed power supply systems, and the second concerning the systems for railway rolling stock. In particular, after a historical introduction to the framework of technological solutions in current use, the authors investigate electrification systems for the power supply of rail vehicles, trams, and subways. Electrical Railway Transportation Systems explores the direct current systems used throughout the world for urban and suburban transport, which are also used in various countries for regional transport. It provides a study of alternating current systems, whether for power supply frequency or for special railway frequency, that are used around the world for ...

  13. Avian respiratory system disorders

    Science.gov (United States)

    Olsen, Glenn H.

    1989-01-01

    Diagnosing and treating respiratory diseases in avian species requires a basic knowledge about the anatomy and physiology of this system in birds. Differences between mammalian and avian respiratory system function, diagnosis, and treatment are highlighted.

  14. BioSystems

    Data.gov (United States)

    U.S. Department of Health & Human Services — The NCBI BioSystems Database provides integrated access to biological systems and their component genes, proteins, and small molecules, as well as literature...

  15. Drinking Water Distribution Systems

    Science.gov (United States)

    Learn about an overview of drinking water distribution systems, the factors that degrade water quality in the distribution system, assessments of risk, future research about these risks, and how to reduce cross-connection control risk.

  16. Immune System and Disorders

    Science.gov (United States)

    Your immune system is a complex network of cells, tissues, and organs that work together to defend against germs. It ... t, to find and destroy them. If your immune system cannot do its job, the results can be ...

  17. US ecology data system

    International Nuclear Information System (INIS)

    Crase, A.

    1987-01-01

    The US Ecology computer data system was instituted March 1, 1982. This system was designed to manage the increasing flow of paperwork and data associated with the receipt and disposal of low-level radioactive waste at Richland, Washington and Beatty, Nevada. The system was modified and upgraded in 1984 to accommodate a revised shipping manifest pursuant to the requirements of 10 CFR 20.311. The data system is used to generate various reports for both internal and external distribution. The computer system is located at US Ecology's corporate headquarters in Louisville, Kentucky. Remote access terminals are located at the disposal sites. The system is supported by a Wang VS-100 processor. In addition to supporting the radwaste data system, the system supports a chemical waste data base, word processing, and electronic mail. The management and operation of this data base are described. 19 figures

  18. Systems engineering management plan

    International Nuclear Information System (INIS)

    Conner, C.W.

    1985-10-01

    The purpose of this Systems Engineering Management Plan (SEMP) is to prescribe the systems engineering procedures to be implemented at the Program level and the minimum requirements for systems engineering at the Program-element level. The Program level corresponds to the Director, OCRWM, or to the organizations within OCRWM to which the Director delegates responsibility for the development of the System and for coordinating and integrating the activities at the Program-element level. The Office of Policy and Outreach (OPO) and the Office of Resource Management (ORM) support the Director at the Program level. The Program-element level corresponds to the organizations within OCRWM (i.e., the Office of Geologic Repositories (OGR) and the Office of Storage and Transportation Systems (OSTS)) with overall responsibility for developing the System elements - that is, the mined geologic disposal system (MGDS), monitored retrievable storage (MRS) (if approved by Congress), and the transportation system

  19. Mobile intelligent autonomous systems

    National Research Council Canada - National Science Library

    Raol, J. R; Gopal, Ajith K

    2013-01-01

    "Written for systems, mechanical, aero, electrical, civil, industrial, and robotics engineers, this book covers robotics from a theoretical and systems point of view, with an emphasis on the sensor...

  20. The remote control system

    International Nuclear Information System (INIS)

    Jansweijer, P.P.M.

    1988-01-01

    The remote-control system is applied in order to control various signals in the car of the spectrometer at distance. The construction (hardware and software) as well as the operation of the system is described. (author). 20 figs