WorldWideScience

Sample records for synthase ohmic conductance

  1. Pentacene ohmic contact on the transparent conductive oxide films

    International Nuclear Information System (INIS)

    Chu, Jian-An; Zeng, Jian-Jhou; Wu, Kuo-Chen; Lin, Yow-Jon

    2010-01-01

    Low-resistance ohmic contacts are essential to improve the performance of pentacene-based electronic and optoelectronic devices. In this study, we reported ohmic contact formation at the indium tin oxide (ITO)/pentacene and indium cerium oxide (ICO)/pentacene interfaces. According to the observed results from current-voltage and Kelvin probe measurements, we found that the lower contact resistivity of the ICO/pentacene sample than the ITO/pentacene sample may be attributed to the higher surface work function of ICO than ITO.

  2. Effect of morphology on the non-ohmic conduction in ZnO nanostructures

    Science.gov (United States)

    Praveen, E.; Jayakumar, K.

    2016-05-01

    Nanostructures of ZnO is synthesized with nanoflower like morphology by simple wet chemical method. The structural, morphological and electrical characterization have been carried out. The temperature dependent electrical characterization of ZnO pellets of thickness 1150 µm is made by the application of 925MPa pressure. The morphological dependence of non-ohmic conduction beyond some arbitrary tunneling potential and grain boundary barrier thickness is compared with the commercially available bulk ZnO. Our results show the suitability of nano-flower like ZnO for the devices like sensors, rectifiers etc.

  3. Conduction noise absorption by ITO thin films attached to microstrip line utilizing Ohmic loss

    International Nuclear Information System (INIS)

    Kim, Sun-Hong; Kim, Sung-Soo

    2010-01-01

    For the aim of wide-band noise absorbers with a special design for low frequency performance, this study proposes conductive indium-tin oxide (ITO) thin films as the absorbent materials in microstrip line. ITO thin films were deposited on the polyimide film substrates by rf magnetron cosputtering of In 2 O 3 and Sn targets. The deposited ITO films show a typical value of electrical resistivity (∼10 -4 Ω m) and sheet resistance can be controlled in the range of 20-230 Ω by variation in film thickness. Microstrip line with characteristic impedance of 50 Ω was used for determining their noise absorbing properties. It is found that there is an optimum sheet resistance of ITO films for the maximum power absorption. Reflection parameter (S 11 ) is increased with decrease in sheet resistance due to impedance mismatch. On the while, transmission parameter (S 21 ) is decreased with decrease in sheet resistance due to larger Ohmic loss of the ITO films. Experimental results and computational prediction show that the optimum sheet resistance is about 100 Ω. For this film, greater power absorption is predicted in the lower frequency region than ferrite thin films of high magnetic loss, which indicates that Ohmic loss is the predominant loss parameter for power absorption in the low frequency range.

  4. Electrical property heterogeneity at transparent conductive oxide/organic semiconductor interfaces: mapping contact ohmicity using conducting-tip atomic force microscopy.

    Science.gov (United States)

    MacDonald, Gordon A; Veneman, P Alexander; Placencia, Diogenes; Armstrong, Neal R

    2012-11-27

    We demonstrate mapping of electrical properties of heterojunctions of a molecular semiconductor (copper phthalocyanine, CuPc) and a transparent conducting oxide (indium-tin oxide, ITO), on 20-500 nm length scales, using a conductive-probe atomic force microscopy technique, scanning current spectroscopy (SCS). SCS maps are generated for CuPc/ITO heterojunctions as a function of ITO activation procedures and modification with variable chain length alkyl-phosphonic acids (PAs). We correlate differences in small length scale electrical properties with the performance of organic photovoltaic cells (OPVs) based on CuPc/C(60) heterojunctions, built on these same ITO substrates. SCS maps the "ohmicity" of ITO/CuPc heterojunctions, creating arrays of spatially resolved current-voltage (J-V) curves. Each J-V curve is fit with modified Mott-Gurney expressions, mapping a fitted exponent (γ), where deviations from γ = 2.0 suggest nonohmic behavior. ITO/CuPc/C(60)/BCP/Al OPVs built on nonactivated ITO show mainly nonohmic SCS maps and dark J-V curves with increased series resistance (R(S)), lowered fill-factors (FF), and diminished device performance, especially near the open-circuit voltage. Nearly optimal behavior is seen for OPVs built on oxygen-plasma-treated ITO contacts, which showed SCS maps comparable to heterojunctions of CuPc on clean Au. For ITO electrodes modified with PAs there is a strong correlation between PA chain length and the degree of ohmicity and uniformity of electrical response in ITO/CuPc heterojunctions. ITO electrodes modified with 6-8 carbon alkyl-PAs show uniform and nearly ohmic SCS maps, coupled with acceptable CuPc/C(60)OPV performance. ITO modified with C14 and C18 alkyl-PAs shows dramatic decreases in FF, increases in R(S), and greatly enhanced recombination losses.

  5. The effect of correlations on the non-ohmic behavior of the small-polaron hopping conductivity in 1D and 3D disordered systems

    International Nuclear Information System (INIS)

    Dimakogianni, M; Triberis, G P

    2010-01-01

    According to percolation theory the investigation of charge transport in disordered systems is equivalent to the study of the possibility of the passage of the carriers through a random network of impedances which interconnect the different lattice sites. When the site energies are not the same, the energy of a site affects the incoming as well as the outgoing impedances connected to the given site and this gives rise to correlations between neighboring impedances. This new condition characterizes the transport process and imposes the evaluation of the average number of sites accessible by a bond from a given site for all possible configurations of sites that satisfy the percolation condition. The generalized molecular crystal model, appropriate for the study of small-polaron hopping transport in disordered systems, and the Kubo formula permit the evaluation of these impedances. Taking correlations into account, theoretical percolation considerations applicable to one-dimensional and three-dimensional disordered systems, lead to analytical expressions for the temperature and electric field dependence of the DC conductivity at high (multi-phonon-assisted hopping) and low (few-phonon-assisted hopping) temperatures. The theoretical analysis reveals the effect of correlations on the non-ohmic behavior of the small-polaron hopping conductivity and permits the evaluation of the maximum hopping distance. Quantitative estimates of this effect are presented comparing the theoretical results, including correlations with those ignoring them, previously reported, applying them to recent experimental data for a wide temperature range and from low up to moderate electric fields.

  6. Energy Confinement of both Ohmic and LHW Plasma on EAST

    International Nuclear Information System (INIS)

    Yang Yao; Gao Xiang

    2011-01-01

    Study on the characters of energy confinement in both Ohmic and lower hybrid wave (LHW) discharges on EAST is conducted and the linear Ohmic confinement (LOC), saturated ohmic confinement (SOC) and improved Ohmic confinement (IOC) regimes are investigated in this paper. It is observed that an improved confinement mode characterized by both a drop of D α line intensity and an increase in line average density can be triggered by a gas puffing pulse. (magnetically confined plasma)

  7. Rigorous treatment of the non-ohmic d.c. conductivity due to phonon-assisted tunneling from localized to extended states

    International Nuclear Information System (INIS)

    Majernikova, E.

    1984-03-01

    A quantitative treatment of the non-ohmic current response due to delocalization of shallow localized electrons in a model of a disordered solid is given. A phonon-assisted tunneling in electric field from shallow localized to extended states is confirmed as a mechanism leading to the dependence which was experimentally found for chalcogenide glasses. (author)

  8. Neoclassical MHD equilibria with ohmic current

    International Nuclear Information System (INIS)

    Tokuda, Shinji; Takeda, Tatsuoki; Okamoto, Masao.

    1989-01-01

    MHD equilibria of tokamak plasmas with neoclassical current effects (neoclassical conductivity and bootstrap current) were calculated self-consistently. Neoclassical effects on JFT-2M tokamak plasmas, sustained by ohmic currents, were studied. Bootstrap currents flow little for L-mode type equilibria because of low attainable values of poloidal beta, β J . H-mode type equilibria give bootstrap currents of 30% ohmic currents for β J attained by JFT-2M and 100% for β J ≥ 1.5, both of which are sufficient to change the current profiles and the resultant MHD equilibria. Neoclassical conductivity which has roughly half value of the classical Spitzer conductivity brings peaked ohmic current profiles to yield low safety factor at the magnetic axis. Neoclassical conductivity reduces the value of effective Z(Z eff ) which is necessary to give the observed one-turn voltage but it needs impurities accumulating at the center when such peaked current profiles are not observed. (author)

  9. Ohmic Heating: Concept and Applications-A Review.

    Science.gov (United States)

    Kaur, Nimratbir; Singh, A K

    2016-10-25

    Ohmic heating, also known as Joule heating, electrical resistance heating, and direct electrical resistance heating, is a process of heating the food by passing electric current. In ohmic heating the energy is dissipated directly into the food. Electrical conductivity is a key parameter in the design of an effective ohmic heater. A large number of potential applications exist for ohmic heating, including blanching, evaporation, dehydration, fermentation, sterilization, pasteurization, and heating of foods. Beyond heating, applied electric field under ohmic heating causes electroporation of cell membranes, which increase extraction rates, and reduce gelatinization temperature and enthalpy. Ohmic heating results in faster heating of food along with maintenance of color and nutritional value of food. Water absorption index, water solubility index, thermal properties, and pasting properties are altered with the application of ohmic heating. Ohmic heating results in pre-gelatinized starches, which reduce energy requirement during processing. But its higher initial cost, lack of its applications in foods containing fats and oils, and less awareness limit its use.

  10. Energy balance in the ohmically heated FT

    International Nuclear Information System (INIS)

    Bartiromo, R.; Brusati, M.; Cilloco, F.

    1981-01-01

    A typical discharge in the FT Tokamak at 60 kG has been studied in detail in order to derive the power balance between the ohmic input and the plasma losses. Impurity and radiation losses together with ion and electron energy balance are discussed. A power transport term for electrons is derived which is ascribed to anomalous thermal conduction. This resulting thermal transport is compared with those derived from different proposed scalings

  11. Energy confinement comparison of ohmically heated stellarators to tokamaks

    International Nuclear Information System (INIS)

    Chu, T.K.; Lee, Y.C.

    1979-12-01

    An empirical scaling prescribes that the energy confinement time in ohmically heated stellarators and tokamaks is proportional to the internal energy of the plasma and the minor radius, and inversely proportional to the current density. A thermal-conduction energy transport model, based on a heuristic assumption that the effective momentum transfer in the radial direction is proportional to the classical parallel momentum transfer which results in ohmic heating, is used to explain this scaling

  12. Technology, applications and modelling of ohmic heating: a review.

    Science.gov (United States)

    Varghese, K Shiby; Pandey, M C; Radhakrishna, K; Bawa, A S

    2014-10-01

    Ohmic heating or Joule heating has immense potential for achieving rapid and uniform heating in foods, providing microbiologically safe and high quality foods. This review discusses the technology behind ohmic heating, the current applications and thermal modeling of the process. The success of ohmic heating depends on the rate of heat generation in the system, the electrical conductivity of the food, electrical field strength, residence time and the method by which the food flows through the system. Ohmic heating is appropriate for processing of particulate and protein rich foods. A vast amount of work is still necessary to understand food properties in order to refine system design and maximize performance of this technology in the field of packaged foods and space food product development. Various economic studies will also play an important role in understanding the overall cost and viability of commercial application of this technology in food processing. Some of the demerits of the technology are also discussed.

  13. Developing and modelling of ohmic heating for solid food products

    DEFF Research Database (Denmark)

    Feyissa, Aberham Hailu; Frosch, Stina

    Heating of solid foods using the conventional technologies is time-consuming due to the fact that heat transfer is limited by internal conduction within the product. This is a big challenge to food manufactures who wish to heat the product faster to the desired core temperature and to ensure more...... uniform quality across the product. Ohmic heating is one of the novel technologies potentially solving this problem by allowing volumetric heating of the product and thereby reducing or eliminating temperature gradients within the product. However, the application of ohmic heating for solid food products...... such as meat and seafood is not industrially utilized yet. Therefore, the aim of the current work is to model and develop the ohmic heating technology for heating of solid meat and seafood. A 3D mathematical model of coupled heat transfer and electric field during ohmic heating of meat products has been...

  14. Ohmic contacts to InN-based materials

    Directory of Open Access Journals (Sweden)

    Sai P. O.

    2016-10-01

    Full Text Available The key aspects of ohmic contact formation to InN-based materials were investigated. Detailed analysis of studies conducted over the past three decades, allows determining the basic principles of such contacts. The contact structure properties and optimal conditions for them are presented. Different types of metallization are considered, the advantages and disadvantages of each are determined, including the basic requirements that such contact must meet. There is emphasis on the using multilayer metallization with the barrier layers. In the case of the InAlN/GaN systems, the general approaches of forming ohmic contacts were considered.

  15. Ohmic contacts to semiconducting diamond

    Science.gov (United States)

    Zeidler, James R.; Taylor, M. J.; Zeisse, Carl R.; Hewett, C. A.; Delahoussaye, Paul R.

    1990-10-01

    Work was carried out to improve the electron beam evaporation system in order to achieve better deposited films. The basic system is an ion pumped vacuum chamber, with a three-hearth, single-gun e-beam evaporator. Four improvements were made to the system. The system was thoroughly cleaned and new ion pump elements, an e-gun beam adjust unit, and a more accurate crystal monitor were installed. The system now has a base pressure of 3 X 10(exp -9) Torr, and can easily deposit high-melting-temperature metals such as Ta with an accurately controlled thickness. Improved shadow masks were also fabricated for better alignment and control of corner contacts for electrical transport measurements. Appendices include: A Thermally Activated Solid State Reaction Process for Fabricating Ohmic Contacts to Semiconducting Diamond; Tantalum Ohmic Contacts to Diamond by a Solid State Reaction Process; Metallization of Semiconducting Diamond: Mo, Mo/Au, and Mo/Ni/Au; Specific Contact Resistance Measurements of Ohmic Contracts to Diamond; and Electrical Activation of Boron Implanted into Diamond.

  16. Flexible carbon-based ohmic contacts for organic transistors

    Science.gov (United States)

    Brandon, Erik (Inventor)

    2007-01-01

    The present invention relates to a system and method of organic thin-film transistors (OTFTs). More specifically, the present invention relates to employing a flexible, conductive particle-polymer composite material for ohmic contacts (i.e. drain and source).

  17. Empirical scaling for present Ohmically heated tokamaks

    International Nuclear Information System (INIS)

    Daughney, C.

    1975-01-01

    Experimental results from the Adiabatic Toroidal Compressor (ATC) tokamak are used to obtain empirical scaling laws for the average electron temperature and electron energy confinement time as functions of the average electron density, the effective ion charge, and the plasma current. These scaling laws are extended to include dependence upon minor and major plasma radius and toroidal field strength through a comparison of the various tokamaks described in the literature. Electron thermal conductivity is the dominant loss process for the ATC tokamak. The parametric dependences of the observed electron thermal conductivity are not explained by present theoretical considerations. The electron temperature obtained with Ohmic heating is shown to be a function of current density - which will not be increased in the next generation of large tokamaks. However, the temperature dependence of the electron energy confinement time suggests that significant improvement in confinement time will be obtained with supplementary electron heating. (author)

  18. Empirical scaling for present ohmic heated tokamaks

    International Nuclear Information System (INIS)

    Daughney, C.

    1975-06-01

    Empirical scaling laws are given for the average electron temperature and electron energy confinement time as functions of plasma current, average electron density, effective ion charge, toroidal magnetic field, and major and minor plasma radius. The ohmic heating is classical, and the electron energy transport is anomalous. The present scaling indicates that ohmic-heating becomes ineffective with larger experiments. (U.S.)

  19. EPR ohmic heating energy storage

    International Nuclear Information System (INIS)

    Heck, F.M.; Stillwagon, R.E.; King, E.I.

    1977-01-01

    The Ohmic Heating (OH) Systems for all the Experimental Power Reactor (EPR) designs to date have all used temporary energy storage to assist in providing the OH current charge required to build up the plasma current. The energies involved (0.8 x 10 9 J to 1.9 x 10 9 J) are so large as to make capacitor storage impractical. Two alternative approaches are homopolar dc generators and ac generators. Either of these can be designed for pulse duty and can be made to function in a manner similar to a capacitor in the OH circuit and are therefore potential temporary energy storage devices for OH systems for large tokamaks. This study compared total OH system costs using homopolar and ac generators to determine their relative merits. The total system costs were not significantly different for either type of machine. The added flexibility and the lower maintenance of the ac machine system make it the more attractive approach

  20. Laminar forced convection in a cylindrical collinear ohmic sterilizer

    Directory of Open Access Journals (Sweden)

    Pesso Tommaso

    2017-01-01

    Full Text Available The present work deals with a thermo-fluid analysis of a collinear cylindrical ohmic heater in laminar flow. The geometry of interest is a circular electrically insulated glass pipe with two electrodes at the pipe ends. For this application, since the electrical conductivity of a liquid food depends strongly on the temperature, the thermal analysis of an ohmic heater requires the simultaneous solution of the electric and thermal fields. In the present work the analysis involves decoupling the previous fields by means of an iterative procedure. The thermal field has been calculated using an analytical solution, which leads to fast calculations for the temperature distribution in the heater. Some considerations of practical interest for the design are also given.

  1. Innovative food processing technology using ohmic heating and aseptic packaging for meat.

    Science.gov (United States)

    Ito, Ruri; Fukuoka, Mika; Hamada-Sato, Naoko

    2014-02-01

    Since the Tohoku earthquake, there is much interest in processed foods, which can be stored for long periods at room temperature. Retort heating is one of the main technologies employed for producing it. We developed the innovative food processing technology, which supersede retort, using ohmic heating and aseptic packaging. Electrical heating involves the application of alternating voltage to food. Compared with retort heating, which uses a heat transfer medium, ohmic heating allows for high heating efficiency and rapid heating. In this paper we ohmically heated chicken breast samples and conducted various tests on the heated samples. The measurement results of water content, IMP, and glutamic acid suggest that the quality of the ohmically heated samples was similar or superior to that of the retort-heated samples. Furthermore, based on the monitoring of these samples, it was observed that sample quality did not deteriorate during storage. © 2013. Published by Elsevier Ltd on behalf of The American Meat Science Association. All rights reserved.

  2. Super high field ohmically heated tokamak operation

    International Nuclear Information System (INIS)

    Cohn, D.R.; Bromberg, L.; Leclaire, R.J.; Potok, R.E.; Jassby, D.L.

    1986-01-01

    The authors discuss a super high field mode of tokamak operation that uses ohmic heating or near ohmic heating to ignition. The super high field mode of operation uses very high values of Β/sup 2/α, where Β is the magnetic field and a is the minor radius (Β/sup 2/α > 100 T/sup 2/m). We analyze copper magnet devices with major radii from 1.7 to 3.0 meters. Minimizing or eliminating the need for auxiliary heating has the potential advantages of reducing uncertainty in extrapolating the energy confinement time of current tokamak devices, and reducing engineering problems associated with large auxiliary heating requirements. It may be possible to heat relatively short pulse, inertially cooled tokamaks to ignition with ohmic power alone. However, there may be advantages in using a very small amount of auxiliary power (less than the ohmic heating power) to boost the ohmic heating and provide a faster start-up, expecially in relatively compact devices

  3. Remarks on the thermal stability of an Ohmic-heated nanowire

    Science.gov (United States)

    Timsit, Roland S.

    2018-05-01

    The rise in temperature of a wire made from specific materials, due to ohmic heating by a DC electrical current, may lead to uncontrollable thermal runaway with ensuing melting. Thermal runaway stems from a steep decrease with increasing temperature of the thermal conductivity of the conducting material and subsequent trapping of the ohmic heat in the wire, i.e., from the inability of the wire to dissipate the heat sufficiently quickly by conduction to the cooler ends of the wire. In this paper, we show that the theory used to evaluate the temperature of contacting surfaces in a bulk electrical contact may be applied to calculate the conditions for thermal runaway in a nanowire. Implications of this effect for electrical contacts are addressed. A possible implication for memory devices using ohmic-heated nanofilms or nanowires is also discussed.

  4. Nutritional impact of ohmic heating on fruits and vegetables—A review

    Directory of Open Access Journals (Sweden)

    Ranvir Kaur

    2016-12-01

    Full Text Available Ohmic heating, also called electrical resistance heating, joule heating, or electro-conductive heating, is an advanced thermal food processing technique where heat is internally generated in a sample due to electrical resistance when electric current is passed through it. It is a novel technique which provides rapid and uniform heating, resulting in less thermal damage to the food product. According to the recent literature, plant products are most suitable and often used for ohmic heat processing. Beyond heating of fruits and vegetables, the applied electric field under ohmic heating causes various changes in quality and nutritional parameters which include inactivation of enzymes and micro-organisms, degradation of heat-sensitive compounds, changes in cell membranes, viscosity, pH, color, and rheology. Ohmic heating rate depends on the electrical field strength and electrical conductivity of product. This review focuses on various factors affecting the electrical conductivity of fruits and vegetables and the effect of ohmic heating on their quality and nutritional properties.

  5. Analysis of the ion energy transport in ohmic discharges in the ASDEX tokamak

    International Nuclear Information System (INIS)

    Simmet, E.E.; Fahrbach, H.U.; Herrmann, W.; Stroth, U.

    1996-10-01

    An analysis of the local ion energy transport is performed for more than one hundred well documented ohmic ASDEX discharges. These are characterized by three different confinement regimes: the linear ohmic confinement (LOC), the saturated ohmic confinement (SOC) and the improved ohmic confinement (IOC). All three are covered by this study. To identify the most important local transport mechanism of the ion heat, the ion power balance equation is analyzed. Two methods are used: straightforward calculation with experimental data only, and a comparison of measured and calculated profiles of the ion temperature and the ion heat conductivity, respectively. A discussion of the power balance shows that conductive losses dominate the ion energy transport in all ohmic discharges of ASDEX. Only inside the q=1-surface losses due to sawtooth activity play a role, while at the edge convective fluxes and CX-losses influence the ion energy transport. Both methods lead to the result that both the ion temperature and the ion heat conductivity are consistent with predictions of the neoclassical theory. Enhanced heat losses as suggested by theories eg. on the basis of η i modes can be excluded. (orig.)

  6. Non-ohmic transport behavior in ultra-thin gold films

    International Nuclear Information System (INIS)

    Alkhatib, A.; Souier, T.; Chiesa, M.

    2011-01-01

    Highlights: → C-AFM study on ultra-thin gold films. → Connection between ultra-thin film morphology and lateral electrical transport. → Transition between ohmic and non-ohmic behavior. → Electrical transition correlation to the film structure continuity. → Direct and indirect tunneling regimes related to discontinuous structures. - Abstract: Structure and local lateral electrical properties of Au films of thicknesses ranging from 10 to 140 nm are studied using conductive atomic force microscopy. Comparison of current maps taken at different thicknesses reveals surprising highly resistive regions (10 10 -10 11 Ω), the density of which increases strongly at lower thickness. The high resistivity is shown to be directly related to discontinuities in the metal sheet. Local I-V curves are acquired to show the nature of electrical behavior relative to thickness. Results show that in Au films of higher thickness the electrical behavior is ohmic, while it is non-ohmic in highly discontinuous films of lower thickness, with the transition happening between 34 and 39 nm. The non-ohmic behavior is explained with tunneling occurring between separated Au islands. The results explain the abrupt increase of electrical resistivity at lower thin film thicknesses.

  7. Bismuth nanowire growth under low deposition rate and its ohmic contact free of interface damage

    Directory of Open Access Journals (Sweden)

    Ye Tian

    2012-03-01

    Full Text Available High quality bismuth (Bi nanowire and its ohmic contact free of interface damage are quite desired for its research and application. In this paper, we propose one new way to prepare high-quality single crystal Bi nanowires at a low deposition rate, by magnetron sputtering method without the assistance of template or catalyst. The slow deposition growth mechanism of Bi nanowire is successfully explained by an anisotropic corner crossing effect, which is very different from existing explanations. A novel approach free of interface damage to ohmic contact of Bi nanowire is proposed and its good electrical conductivity is confirmed by I-V characteristic measurement. Our method provides a quick and convenient way to produce high-quality Bi nanowires and construct ohmic contact for desirable devices.

  8. Ohmic ITBs in Alcator C-Mod

    Science.gov (United States)

    Fiore, C. L.; Rowan, W. L.; Dominguez, A.; Hubbard, A. E.; Ince-Cushman, A.; Greenwald, M. J.; Lin, L.; Marmar, E. S.; Reinke, M.; Rice, J. E.; Zhurovich, K.

    2007-11-01

    Internal transport barrier plasmas can arise spontaneously in ohmic Alcator C-Mod plasmas where an EDA H-mode has been developed by magnetic field ramping. These ohmic ITBs share the hallmarks of ITBs created with off-axis ICRF injection in that they have highly peaked density and pressure profiles and the peaking can be suppressed by on-axis ICRF. There is a reduction of particle and thermal flux in the barrier region which then allows the neoclassical pinch to peak the central density. Recent work on ITB onset conditions [1] which was motivated by turbulence studies [2] points to the broadening of the Ti profile with off-axis ICRF acting to reduce the ion temperature gradient. This suppresses ITG instability driven particle fluxes, which is thought to be the primary mechanism for ITB formation. The object of this study is to examine the characteristics of ohmic ITBs to find whether the stability of plasmas and the plasma parameters support the onset model. [1]K. Zhurovich, et al., To be published in Nuclear Fusion [2] D. R. Ernst, et al., Phys. Plasmas 11, 2637 (2004)

  9. Ohmic Heating Assisted Lye Peeling of Pears.

    Science.gov (United States)

    Gupta, Sarvesh; Sastry, Sudhir K

    2018-05-01

    Currently, high concentrations (15% to 18%) of lye (sodium hydroxide) are used in peeling pears, constituting a wastewater handling and disposal problem for fruit processors. In this study, the effect of ohmic heating on lye peeling of pears was investigated. Pears were peeled using 0.5%, 1%, 2%, and 3% NaOH under different electric field strengths at two run times and their peeled yields were compared to that obtained at 2% and 18% NaOH with conventional heating. Results revealed that ohmic heating results in greater than 95% peeled yields and the best peel quality at much lower concentrations of lye (2% NaOH at 532 V/m and 3% NaOH at 426 and 479 V/m) than those obtained under conventional heating conditions. Treatment times of 30 and 60 s showed no significant differences. Within the studied range, the effects of increasing field strength yielded no significant additional benefits. These results confirm that the concentration of lye can be significantly lowered in the presence of ohmic heating to achieve high peeled yields and quality. Our work shows that lye concentrations can be greatly reduced while peeling pears, resulting in significant savings in use of caustic chemicals, reduced costs for effluent treatment and waste disposal. © 2018 Institute of Food Technologists®.

  10. Benzalacetone Synthase

    Directory of Open Access Journals (Sweden)

    Ikuro eAbe

    2012-03-01

    Full Text Available Benzalacetone synthase, from the medicinal plant Rheum palmatum (Polygonaceae (RpBAS, is a plant-specific chalcone synthase (CHS superfamily of type III polyketide synthase (PKS. RpBAS catalyzes the one-step, decarboxylative condensation of 4-coumaroyl-CoA with malonyl-CoA to produce the C6-C4 benzalacetone scaffold. The X-ray crystal structures of RpBAS confirmed that the diketide-forming activity is attributable to the characteristic substitution of the conserved active-site "gatekeeper" Phe with Leu. Furthermore, the crystal structures suggested that RpBAS employs novel catalytic machinery for the thioester bond cleavage of the enzyme-bound diketide intermediate and the final decarboxylation reaction to produce benzalacetone. Finally, by exploiting the remarkable substrate tolerance and catalytic versatility of RpBAS, precursor-directed biosynthesis efficiently generated chemically and structurally divergent, unnatural novel polyketide scaffolds. These findings provided a structural basis for the functional diversity of the type III PKS enzymes.

  11. On the evaluation of currents in a tokamak plasma during combined Ohmic and RF current drive

    International Nuclear Information System (INIS)

    Eckhartt, D.

    1986-09-01

    By taking into account the rf-generated enhancement of the plasma electric conductivity (as formulated by Fisch in the limit of weak dc electric fields) a relation is derived between the ratio of rf to Ohmically driven currents and other plasma parameters to be measured before and after the rf onset under the condition of constant net plasma current. (author)

  12. TNS superconducting ohmic-heating system

    International Nuclear Information System (INIS)

    Wang, S.T.; Fuja, R.; Kim, S.H.; Kustom, R.L.; Praeg, W.F.; Thompson, K.; Turner, L.R.

    1978-01-01

    The superconducting ohmic-heating (OH) system is the selected design for the General Atomics Co./Argonne National Laboratory TNS tokamak design studies. The key features of the OH system design are: (1) parallel coil connection, (2) better utilization of flux core by embedding support cylinder of the toroidal-field coil within the OH inner radius, (3) independent trim coils for correcting the stray fields, (4) low-loss high-current cryostable cable design and (5) OH coil cycling circuit using a reversing bridge. Detailed designs are presented

  13. Theoretical scaling law for ohmically heated tokamaks

    International Nuclear Information System (INIS)

    Minardi, E.

    1981-06-01

    The electrostatic drift instability arising from the reduction of shear damping, due to toroidal effects, is assumed to be the basic source of the anomalous electron transport in tokamaks. The Maxwellian population of electrons constitutes a medium whose adiabatic nonlinear reaction to the instability (described in terms of an effective dielectric constant of the medium) determines the stationary electrostatic fluctuation level in marginally unstable situations. The existence of a random electrostatic potenial implies a fluctuating current of the Maxwellian electrons which creates a random magnetic field and a stocasticization of a magnetic configuration. The application of recent results allows the calculation of the realted radial electron transport. It is found that the confinement time under stationary ohmic conditions scales as n Tsub(i)sup( - 1/2) and is proportional roughly to the cube of the geometric dimenisions. Moreover, it is deduced that the loop voltage is approximateley the same for all tokamaks, irrespective of temperature and density and to a large extent, also of geometrical conditions. Thes results are characteristic of the ohmic stationary regime and can hardly be extrapolated to order heating regimes. (orig.)

  14. Silver antimony Ohmic contacts to moderately doped n-type germanium

    Energy Technology Data Exchange (ETDEWEB)

    Dumas, D. C. S.; Gallacher, K.; Millar, R.; Paul, D. J., E-mail: Douglas.Paul@glasgow.ac.uk [School of Engineering, University of Glasgow, Rankine Building, Oakfield Avenue, Glasgow G12 8LT (United Kingdom); MacLaren, I. [SUPA School of Physics and Astronomy, University of Glasgow, Kelvin Building, University Avenue, Glasgow G12 8QQ (United Kingdom); Myronov, M.; Leadley, D. R. [Department of Physics, University of Warwick, Coventry CV4 7AL (United Kingdom)

    2014-04-21

    A self doping contact consisting of a silver/antimony alloy that produces an Ohmic contact to moderately doped n-type germanium (doped to a factor of four above the metal-insulator transition) has been investigated. An evaporation of a mixed alloy of Ag/Sb (99%/1%) onto n-Ge (N{sub D}=1×10{sup 18} cm{sup −3}) annealed at 400 °C produces an Ohmic contact with a measured specific contact resistivity of (1.1±0.2)×10{sup −5} Ω-cm{sup 2}. It is proposed that the Ohmic behaviour arises from an increased doping concentration at the Ge surface due to the preferential evaporation of Sb confirmed by transmission electron microscope analysis. It is suggested that the doping concentration has increased to a level where field emission will be the dominate conduction mechanism. This was deduced from the low temperature electrical characterisation of the contact, which exhibits Ohmic behaviour down to a temperature of 6.5 K.

  15. Voltage Controlled Hot Carrier Injection Enables Ohmic Contacts Using Au Island Metal Films on Ge.

    Science.gov (United States)

    Ganti, Srinivas; King, Peter J; Arac, Erhan; Dawson, Karl; Heikkilä, Mikko J; Quilter, John H; Murdoch, Billy; Cumpson, Peter; O'Neill, Anthony

    2017-08-23

    We introduce a new approach to creating low-resistance metal-semiconductor ohmic contacts, illustrated using high conductivity Au island metal films (IMFs) on Ge, with hot carrier injection initiated at low applied voltage. The same metallization process simultaneously allows ohmic contact to n-Ge and p-Ge, because hot carriers circumvent the Schottky barrier formed at metal/n-Ge interfaces. A 2.5× improvement in contact resistivity is reported over previous techniques to achieve ohmic contact to both n- and p- semiconductor. Ohmic contacts at 4.2 K confirm nonequilibrium current transport. Self-assembled Au IMFs are strongly orientated to Ge by annealing near the Au/Ge eutectic temperature. Au IMF nanostructures form, provided the Au layer is below a critical thickness. We anticipate that optimized IMF contacts may have applicability to many material systems. Optimizing this new paradigm for metal-semiconductor contacts offers the prospect of improved nanoelectronic systems and the study of voltage controlled hot holes and electrons.

  16. Period doubling in a model of magnetoconvection with Ohmic heating

    International Nuclear Information System (INIS)

    Osman, M. B. H.

    2000-01-01

    In this work it has been studied an idealized model of rotating nonlinear magneto convection to investigate the effects of Ohmic heating. In the over stable region it was found that Ohmic heating can lead to a period-doubling sequence

  17. Simulation of core turbulence measurement in Tore Supra ohmic regimes

    NARCIS (Netherlands)

    Hacquin, S.; Citrin, J.; Arnichand, H.; Sabot, R.; Bourdelle, C.; Garbet, X.; Kramer-Flecken, A.; Tore Supra team,

    2016-01-01

    This paper reports on a simulation of reflectometry measurement in Tore Supra ohmic discharges, for which the experimental observations as well as gyrokinetic non-linear computations predict a modification of turbulence spectrum between the linear (LOC) and the saturated ohmic confinement (SOC)

  18. Ignited tokamak devices with ohmic-heating dominated startup

    International Nuclear Information System (INIS)

    Cohn, D.R.; Bromberg, L.; Jassby, D.L.

    1986-01-01

    Startup of tokamaks such that the auxiliary heating power is significantly less than the ohmic heating power at all times during heating to ignition can be referred to as ''Ohmic-heating dominated startup.'' Operation in this mode could increase the certainty of heating to ignition since energy confinement during startup may be described by present scaling laws for ohmic heating. It could also reduce substantially the auxiliary heating power (the required power may be quite large for auxiliary-heating dominated startup). These advantages might be realized without the potentially demanding requirements for pure ohmic heating to ignition. In this paper the authors discuss the requirements for ohmic-heating dominated startup and present illustrative design parameters for compact experiment ignition devices that use high performance copper magnets

  19. Ohmic Heating System for the TFTR Tokamak

    International Nuclear Information System (INIS)

    Petree, F.; Cassel, R.

    1977-01-01

    The TFTR Ohmic Heating (OH) System will apply 140,000 volt impulses upon the OH coils to start the plasma. In order to reduce the voltage stress to ground on the OH coils to 12 kV without changing the magnetic field induced by the OH system in the plasma, six d-c current interrupters will be applied to six entry points in the OH coil system. And in order to impart a nearly rectangular shape to these impulses, the voltage determining elements will be nonlinear resistances placed in parallel with the interrupters. These nonlinear resistors, made of semiconducting material, are not normally used in repetitive or continuous duty, and their proper functioning is crucial to the reliable operation of the system. The system described herein, is being revised owing to the impact of revisions to the Toroidal Field Coil System, and to refinements to the OH System design

  20. Graphene in ohmic contact for both n-GaN and p-GaN

    Energy Technology Data Exchange (ETDEWEB)

    Zhong, Haijian; Liu, Zhenghui; Shi, Lin; Xu, Gengzhao; Fan, Yingmin; Huang, Zengli [Suzhou Institute of Nano-Tech and Nano-Bionics, CAS, Suzhou 215123 (China); Wang, Jianfeng; Ren, Guoqiang; Xu, Ke, E-mail: kxu2006@sinano.ac.cn [Suzhou Institute of Nano-Tech and Nano-Bionics, CAS, Suzhou 215123 (China); Suzhou Nanowin Science and Technology Co., Ltd., Suzhou 215123 (China)

    2014-05-26

    The wrinkles of single layer graphene contacted with either n-GaN or p-GaN were found both forming ohmic contacts investigated by conductive atomic force microscopy. The local I–V results show that some of the graphene wrinkles act as high-conductive channels and exhibiting ohmic behaviors compared with the flat regions with Schottky characteristics. We have studied the effects of the graphene wrinkles using density-functional-theory calculations. It is found that the standing and folded wrinkles with zigzag or armchair directions have a tendency to decrease or increase the local work function, respectively, pushing the local Fermi level towards n- or p-type GaN and thus improving the transport properties. These results can benefit recent topical researches and applications for graphene as electrode material integrated in various semiconductor devices.

  1. Study of degradation processes kinetics in ohmic contacts of resonant tunneling diodes based on nanoscale AlAs/GaAs heterostructures under influence of temperature

    Science.gov (United States)

    Makeev, M. O.; Meshkov, S. A.

    2017-07-01

    The artificial aging of resonant tunneling diodes based on nanoscale AlAs/GaAs heterostructures was conducted. As a result of the thermal influence resonant tunneling diodes IV curves degrade firstly due to ohmic contacts' degradation. To assess AlAs/GaAs resonant tunneling diodes degradation level and to predict their reliability, a functional dependence of the contact resistance of resonant tunneling diode AuGeNi ohmic contacts on time and temperature was offered.

  2. Achieving improved ohmic confinement via impurity injection

    International Nuclear Information System (INIS)

    Bessenrodt-Weberpals, M.; Soeldner, F.X.

    1991-01-01

    Improved Ohmic Confinement (IOC) was obtained in ASDEX after a modification of the divertors that allowed a larger (deuterium and impurity) backflow from the divertor chamber. The quality of IOC depended crucially on the wall conditions, i.e. IOC was best for uncovered stainless steels walls and vanished with boronization. Furthermore, IOC was found only in deuterium discharges. These circumstances led to the idea that IOC correlates with the content of light impurities in the plasma. To substantiate this working hypothesis, we present observations in deuterium discharges with boronized wall conditions into which various impurities have been injected with the aim to induce IOC conditions. Firstly, the plasma behaviour in typical IOC discharges is characterized. Secondly, injection experiments with the low-Z impurities nitrogen and neon as well as with the high-Z impurities argon and krypton are discussed. Then, we concentrate on optimized neon puffing that yields the best confinement results which are similar to IOC conditions. Finally, these results are compared with eperiments in other tokamaks and some conclusions are drawn about the effects of the impurity puffing on both, the central and the edge plasma behaviour. (orig.)

  3. Spectroscopic study of ohmically heated Tokamak discharges

    International Nuclear Information System (INIS)

    Breton, C.; Michelis, C. de; Mattioli, M.

    1980-07-01

    Tokamak discharges interact strongly with the wall and/or the current aperture limiter producing recycling particles, which penetrate into the discharge and which can be studied spectroscopically. Working gas (hydrogen or deuterium) is usually studied observing visible Balmer lines at several toroidal locations. Absolute measurements allow to obtain both the recycling flux and the global particle confinement time. With sufficiently high resolution the isotopic plasma composition can be obtained. The impurity elements can be divided into desorbed elements (mainly oxygen) and eroded elements (metals from both walls and limiter) according to the plasma-wall interaction processes originating them. Space-and time-resolved emission in the VUV region down to about 20 A will be reviewed for ohmically-heated discharges. The time evolution can be divided into four phases, not always clearly separated in a particular discharge: a) the initial phase, lasting less than 10 ms (the so-called burn-out phase), b) the period of increasing plasma current and electron temperature, lasting typically 10 - 100 ms, c) an eventual steady state (plateau of the plasma current with almost constant density and temperature), d) the increase of the electron density up to or just below the maximum value attainable in a given device. For all these phases the results reported from different devices will be described and compared

  4. Ohmic Contacts to P-Type SiC

    National Research Council Canada - National Science Library

    Crofton, John

    2000-01-01

    Alloys of aluminum (Al) have previously been used as ohmic contacts to p-type SiC, however the characteristics and performance of these contacts is drastically affected by the type and composition of the Al alloy...

  5. Three-dimensional stellarator equilibrium as an ohmic steady state

    International Nuclear Information System (INIS)

    Park, W.; Monticello, D.A.; Strauss, H.; Manickam, J.

    1985-07-01

    A stable three-dimensional stellarator equilibrium can be obtained numerically by a time-dependent relaxation method using small values of dissipation. The final state is an ohmic steady state which approaches an ohmic equilibrium in the limit of small dissipation coefficients. We describe a method to speed up the relaxation process and a method to implement the B vector . del p = 0 condition. These methods are applied to obtain three-dimensional heliac equilibria using the reduced heliac equations

  6. Sawtooth-free Ohmic discharges in ASDEX and the aspects of neoclassical ion transport

    International Nuclear Information System (INIS)

    Stroth, U.; Fussmann, G.; Krieger, K.; Mertens, V.; Wagner, F.; Bessenrodt-Weberpals, M.; Buechse, R.; Giannone, L.; Herrmann, H.; Simmet, E.; Steuer, K.H.

    1991-05-01

    Sawtooth-free Ohmic discharges can serve as a model case for a quiescent Tokamak plasma. We report on the properties and the global parameters of these discharges observed in ASDEX and make comments on the mechanism which seems to be responsible for the stabilization of the sawtooth instability. Stationary Ohmic discharge were used to investigate particle, impurity and energy transport in the absence of the sawtooth instability. Particular emphasis has been devoted to a comparison with the predictions of neoclassical theories. We find that the ion energy transport is on the level predicted by neoclassical theory and can explain particle and impurity transport with neoclassical inward drift velocities and diffusion coefficients with the same small anomalous contribution. In the central region of the plasma, where the power flux is low, very small values were found for the electron heat conductivity. (orig.)

  7. Transport simulations of ohmic ignition experiment: IGNITEX

    International Nuclear Information System (INIS)

    Uckan, N.A.; Howe, H.C.

    1987-01-01

    The IGNITEX device, proposed by Rosenbluth et al., is a compact, super-high-field, high-current, copper-coil tokamak envisioned to reach ignition with ohmic (OH) heating alone. Several simulations of IGNITEX were made with a 0-D global model and with the 1-D PROCTR transport code. It is shown that OH ignition is a sensitive function of the assumptions about density profile, wall reflectivity of synchrotron radiation, impurity radiation, plasma edge conditions, and additional anomalous losses. In IGNITEX, OH ignition is accessible with nearly all scalings based on favorable OH confinement (such as neo-Alcator). Also, OH ignition appears to be accessible for most (not all) L-mode scalings (such as Kaye-Goldston), provided that the density profile is not too broad (parabolic or more peaked profiles are needed), Z/sub eff/ is not too large (≤2), and anomalous radiation and alpha losses and/or other enhanced transport losses (/eta//sub i/ modes, edge convective energy losses, etc.) are not present. In IGNITEX, because the figure-of-merit parameters (aB 0 2 /q* /approximately/ IB 0 , etc.) are large, ignition can be accessed (either with OH heating alone or with the aid of a small amount of auxiliary power) at relatively low beta, far from stability limits. Once the plasma is ignited, thermal runaway is prevented naturally by a combination of increased synchrotron radiation, burnout of the fuel in the plasma core and replacement by thermal alphas, and the reduction in the thermal plasma confinement assumed in L-mode-like scalings. 12 refs., 5 figs., 1 tab

  8. Transport simulations of ohmic ignition experiment: IGNITEX

    International Nuclear Information System (INIS)

    Uckan, N.A.; Howe, H.C.

    1987-12-01

    The IGNITEX device, proposed by Rosenbluth et al., is a compact, super-high-field, high-current, copper-coil tokamak envisioned to reach ignition with ohmic (OH) heating alone. Several simulations of IGNITEX were made with a 0-D global model and with the 1-D PROCTR transport code. It is shown that OH ignition is a sensitive function of the assumptions about density profile, wall reflectivity of synchrotron radiation, impurity radiation, plasma edge conditions, and additional anomalous losses. In IGNITEX, OH ignition is accessible with nearly all scalings based on favorable OH confinement (such as neo-Alcator). Also, OH ignition appears to be accessible for most (not all) L-mode scalings (such as Kaye-Goldston), provided that the density profile is not too broad (parabolic or more peaked profiles are needed), Z/sub eff/ is not too large, and anomalous radiation and alpha losses and/or other enhanced transport losses (eta/sub i/ modes, edge convective energy losses, etc.) are not present. In IGNITEX, because the figure-of-merit parameters are large, ignition can be accessed (either with OH heating alone or with the aid of a small amount of auxiliary power) at relatively low beta, far from stability limits. Once the plasma is ignited, thermal runaway is prevented naturally by a combination of increased synchrotron radiation, burnout of the fuel in the plasma core and replacement by thermal alphas, and the reduction in the thermal plasma confinement assumed in L-mode-like scalings. 12 refs., 5 figs., 1 tab

  9. Metallization systems for stable ohmic contacts to GaAs

    International Nuclear Information System (INIS)

    Tandon, J.L.; Douglas, K.D.; Vendura, G.; Kolawa, E.; So, F.C.T.; Nicolet, M.A.

    1986-01-01

    A metallization scheme to form reproducible and stable ohmic contacts to GaAs is described. The approach is based on the configuration: GaAs/X/Y/Z; where X is a thin metal film (e.g. Pt, Ti, Pd, Ru), Y is an electrically conducting diffusion barrier layer (TiN, W or W/sub 0.7/N/sub 0.3/), and Z is a thick metal layer (e.g. Ag) typically required for bonding or soldering purposes. The value and reproducibility of the contact resistance in these metallization systems results from the uniform steady-state solid-phase reaction of the metal X with GaAs. The stability of the contacts is achieved by the diffusion barrier layer Y, which not only confines the reaction of X with GaAs, but also prevents the top metal layer Z from interfering with this reaction. Applications of such contacts in fabricating stable solar cells are also discussed

  10. Analytical models of Ohmic heating and conventional heating in food processing

    Science.gov (United States)

    Serventi, A.; Bozzoli, F.; Rainieri, S.

    2017-11-01

    Ohmic heating is a food processing operation in which an electric current is passed through a food and the electrical resistance of the food causes the electric power to be transformed directly into heat. The heat is not delivered through a surface as in conventional heat exchangers but it is internally generated by Joule effect. Therefore, no temperature gradient is required and it origins quicker and more uniform heating within the food. On the other hand, it is associated with high energy costs and its use is limited to a particular range of food products with an appropriate electrical conductivity. Sterilization of foods by Ohmic heating has gained growing interest in the last few years. The aim of this study is to evaluate the benefits of Ohmic heating with respect to conventional heat exchangers under uniform wall temperature, a condition that is often present in industrial plants. This comparison is carried out by means of analytical models. The two different heating conditions are simulated under typical circumstances for the food industry. Particular attention is paid to the uniformity of the heat treatment and to the heating section length required in the two different conditions.

  11. Comparative Study Between Internal Ohmic Resistance and Capacity for Battery State of Health Estimation

    Directory of Open Access Journals (Sweden)

    M. Nisvo Ramadan

    2015-12-01

    Full Text Available In order to avoid battery failure, a battery management system (BMS is necessary. Battery state of charge (SOC and state of health (SOH are part of information provided by a BMS. This research analyzes methods to estimate SOH based lithium polymer battery on change of its internal resistance and its capacity. Recursive least square (RLS algorithm was used to estimate internal ohmic resistance while coloumb counting was used to predict the change in the battery capacity. For the estimation algorithm, the battery terminal voltage and current are set as the input variables. Some tests including static capacity test, pulse test, pulse variation test and before charge-discharge test have been conducted to obtain the required data. After comparing the two methods, the obtained results show that SOH estimation based on coloumb counting provides better accuracy than SOH estimation based on internal ohmic resistance. However, the SOH estimation based on internal ohmic resistance is faster and more reliable for real application

  12. Mathematical model of solid food pasteurization by ohmic heating: influence of process parameters.

    Science.gov (United States)

    Marra, Francesco

    2014-01-01

    Pasteurization of a solid food undergoing ohmic heating has been analysed by means of a mathematical model, involving the simultaneous solution of Laplace's equation, which describes the distribution of electrical potential within a food, the heat transfer equation, using a source term involving the displacement of electrical potential, the kinetics of inactivation of microorganisms likely to be contaminating the product. In the model, thermophysical and electrical properties as function of temperature are used. Previous works have shown the occurrence of heat loss from food products to the external environment during ohmic heating. The current model predicts that, when temperature gradients are established in the proximity of the outer ohmic cell surface, more cold areas are present at junctions of electrodes with lateral sample surface. For these reasons, colder external shells are the critical areas to be monitored, instead of internal points (typically geometrical center) as in classical pure conductive heat transfer. Analysis is carried out in order to understand the influence of pasteurisation process parameters on this temperature distribution. A successful model helps to improve understanding of these processing phenomenon, which in turn will help to reduce the magnitude of the temperature differential within the product and ultimately provide a more uniformly pasteurized product.

  13. Ohmic Heating: An Emerging Concept in Organic Synthesis.

    Science.gov (United States)

    Silva, Vera L M; Santos, Luis M N B F; Silva, Artur M S

    2017-06-12

    The ohmic heating also known as direct Joule heating, is an advanced thermal processing method, mainly used in the food industry to rapidly increase the temperature for either cooking or sterilization purposes. Its use in organic synthesis, in the heating of chemical reactors, is an emerging method that shows great potential, the development of which has started recently. This Concept article focuses on the use of ohmic heating as a new tool for organic synthesis. It presents the fundamentals of ohmic heating and makes a qualitative and quantitative comparison with other common heating methods. A brief description of the ohmic reactor prototype in operation is presented as well as recent examples of its use in organic synthesis at laboratory scale, thus showing the current state of the research. The advantages and limitations of this heating method, as well as its main current applications are also discussed. Finally, the prospects and potential implications of ohmic heating in future research in chemical synthesis are proposed. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Mechanisms of current flow in metal-semiconductor ohmic contacts

    International Nuclear Information System (INIS)

    Blank, T. V.; Gol'dberg, Yu. A.

    2007-01-01

    Published data on the properties of metal-semiconductor ohmic contacts and mechanisms of current flow in these contacts (thermionic emission, field emission, thermal-field emission, and also current flow through metal shunts) are reviewed. Theoretical dependences of the resistance of an ohmic contact on temperature and the charge-carrier concentration in a semiconductor were compared with experimental data on ohmic contacts to II-VI semiconductors (ZnSe, ZnO), III-V semiconductors (GaN, AlN, InN, GaAs, GaP, InP), Group IV semiconductors (SiC, diamond), and alloys of these semiconductors. In ohmic contacts based on lightly doped semiconductors, the main mechanism of current flow is thermionic emission with the metal-semiconductor potential barrier height equal to 0.1-0.2 eV. In ohmic contacts based on heavily doped semiconductors, the current flow is effected owing to the field emission, while the metal-semiconductor potential barrier height is equal to 0.3-0.5 eV. In alloyed In contacts to GaP and GaN, a mechanism of current flow that is not characteristic of Schottky diodes (current flow through metal shunts formed by deposition of metal atoms onto dislocations or other imperfections in semiconductors) is observed

  15. Ti(r) profiles from the JET neutron profile monitor for ohmic discharges

    Energy Technology Data Exchange (ETDEWEB)

    Esposito, B. (ENEA, Frascati (Italy). Centro Ricerche Energia); Marcus, F.B.; Conroy, S.; Jarvis, O.N.; Loughlin, M.J.; Sadler, G.; Belle, P. van (Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking); Adams, J.M.; Watkins, N. (AEA Industrial Technology, Harwell (United Kingdom))

    1991-01-01

    A study has been made of the neutron emissivity, using the JET neutron profile monitor, obtained for ohmically heated deuterium discharges. Both one-dimensional (1-D) best-fit inversion procedures and 2-D tomography have been used to deduce the radial profile of the neutron emission from the line-integral data. The profiles of ion temperature and ion thermal conductivity are then derived. The scaling of the ion thermal conductivity with plasma current is found to be opposite to that of neoclassical theory. (author) 4 refs., 5 figs.

  16. Start-up of the ohmic phase in JET

    International Nuclear Information System (INIS)

    Tanga, A.; Christiansen, J.P.; Cordey, J.G.; Ejima, S.; Kellman, A.; Lazzaro, E.; Lomas, P.J.; Thomas, P.R.

    1985-01-01

    JET has been designed to permit the study of plasmas in which alphaparticle heating is a significant part of the power balance. In order to have a sufficient thermonuclear yield and to trap the resulting alphaparticles, JET is similar in its dimensions and plasma current to the next generation of reactor-like devices such as NET, FER and INTOR. For this reason, the authors see the results from the study of the start-up of ohmically heated plasmas in JET as highly relevant. Discussed is the range that has been achieved in all major parameters with ohmic heating. Experiences with the wall conditioning technique and the results of ion cyclotron heating experiments in JET are outlined. This paper also describes the stages of plasma formation, current rise and ohmic flat-top

  17. Ohmic ignition of Neo-Alcator tokamak with adiabatic compression

    International Nuclear Information System (INIS)

    Inoue, Nobuyuki; Ogawa, Yuichi

    1992-01-01

    Ohmic ignition condition on axis of the DT tokamak plasma heated by minor radius and major radius adiabatic compression is studied assuming parabolic profiles for plasma parameters, elliptic plasma cross section, and Neo-Alcator confinement scaling. It is noticeable that magnetic compression reduces the necessary total plasma current for Ohmic ignition device. Typically in compact ignition tokamak of the minor radius of 0.47 m, major radius of 1.5 m and on-axis toroidal field of 20 T, the plasma current of 6.8 MA is sufficient for compression plasma, while that of 11.7 MA is for no compression plasma. Another example with larger major radius is also described. In such a device the large flux swing of Ohmic transformer is available for long burn. Application of magnetic compression saves the flux swing and thereby extends the burn time. (author)

  18. Computational studies of ohmic heating in the spheromak

    International Nuclear Information System (INIS)

    Olson, R.E.

    1983-01-01

    Time-dependent computational simulations using both single-fluid O-D and two-fluid 1 1/2-D models are developed for and utilized in an investigation of the ohmic heating of a spheromak plasma. The plasma density and composition, the applied magnetic field strength, the plasma size, and the plasma current density profile are considered for their effects on the spheromak heating rate and maximum achievable temperature. The feasibility of ohmic ignition of a reactor-size spheromak plasma is also contemplated

  19. Ohmic discharges in Tore Supra - Marfes and detached plasmas

    International Nuclear Information System (INIS)

    Vallet, J.C.

    1990-01-01

    The Tore Supra plasma characteristics are given. The observed discharges are either leaning on the graphite inner first wall or limited by movable pump limiters located outboard and at the bottom of the vacuum chamber. The particular plasma conditions which lead to marfes and detached plasmas in ohmically heated He and D2 discharges limited by the inner wall are investigated. The results show that the ratio of radiated power to ohmic power increase linearly with M.g. As M.g rises, attached plasma, marfe and detached plasma are sequentially observed. Detached plasma with an effective radius as small as. 7 times the limiter radius was observed on Tore Supra

  20. Effect of milk fat content on the performance of ohmic heating for inactivation of Escherichia coli O157:H7, Salmonella enterica Serovar Typhimurium and Listeria monocytogenes.

    Science.gov (United States)

    Kim, S-S; Kang, D-H

    2015-08-01

    The effect of milk fat content on ohmic heating compared to conventional heating for inactivation of food-borne pathogens was investigated. Sterile cream was mixed with sterile buffered peptone water and adjusted to 0, 3, 7, 10% (w/v) milk fat content. These samples with varying fat content were subjected to ohmic and conventional heating. The effect of milk fat on temperature increase and electrical conductivity were investigated. Also, the protective effect of milk fat on the inactivation of foodborne pathogens was studied. For conventional heating, temperatures of samples increased with time and were not significantly (P > 0.05) different regardless of fat content. Although the inactivation rate of Escherichia coli O157:H7, Salmonella Typhimurium and L. monocytogens decreased in samples of 10% fat content, a protective effect was not observed for conventional heating. In contrast with conventional heating, ohmic heating was significantly affected by milk fat content. Temperature increased more rapidly with lower fat content for ohmic heating due to higher electrical conductivity. Nonuniform heat generation of nonhomogeneous fat-containing samples was verified using a thermal infrared camera. Also, the protective effect of milk fat on E. coli O157:H7 and Listeria monocytogenes was observed in samples subjected to ohmic heating. These results indicate that food-borne pathogens can survive in nonhomogeneous fat-containing foods subjected to ohmic heating. Therefore, more attention is needed regarding ohmic heating than conventional heating for pasteurizing fat-containing foods. The importance of adequate pasteurization for high milk fat containing foods was identified. © 2015 The Society for Applied Microbiology.

  1. Density limit in FTU tokamak during Ohmic operation

    International Nuclear Information System (INIS)

    Frigione, D.; Pieroni, L.

    1993-01-01

    The understanding of the physical mechanisms that regulate the density limit in a Tokamak is very important in view of a future fusion reactor. On one hand density enters as a factor in the figure of merit needed to achieve a burning plasma, and on the other hand a high edge density is a prerequisite for avoiding excessive erosion of the first walls and to limit the impurity influx into the hot plasma core. Furthermore a reactor should work in a safe zone of the operation parameters in order to avoid disruptive instabilities. The density limit problem has been tackled since the 70's, but so far a unique physics picture has not still emerged. In the last few years, due to the availability of better diagnostics, especially for the plasma edge, the use of pellet injectors to fuel the plasma and the experience gained on many different Tokamak, a consensus has been reached on the edge density as the real parameter responsible for the density limit. There are still two main mechanisms invoked to explain this limit: one refers to the power balance between the heat conducted and/or convected across the plasma radius and the power lost by impurity line radiation at the edge. When the latter overcomes the former, shrinking of the current channel occurs, which leads to instabilities due to tearing modes (usually the m/n=2/1) and then to disruption. The other explanation, for now valid for divertor machines, is based on the particle and energy balance in the scrape off layer (SOL). The limit in the edge density is then associated with the thermal collapse of the divertor plasma. In this work we describe the experiments on the density limit in FTU with Ohmic heating, the reason why we also believe that the limit is on the edge density, and discuss its relation to a simple model based on the SOL power balance valid for a limiter Tokamak. (author) 7 refs., 4 figs

  2. Radial profiles of neutron emission from ohmic discharges in JET

    International Nuclear Information System (INIS)

    Cheetham, A.; Gottardi, N.; Jarvis, O.N.

    1989-01-01

    Neutron emission profiles from several ohmically heated discharges have been studied using a variety of analytical techniques to extract the ion temperature profiles which are found to agree well, both in shape and magnitude, with the electron temperature profiles as measured by the LIDAR Thomson scattering diagnostic. (author) 7 refs., 3 figs

  3. Physicochemical properties of masa and corn tortilla made by ohmic ...

    African Journals Online (AJOL)

    Instant corn flour obtained by ohmic heating (OHICF) was used to prepare masa and tortillas. In this study, the effect of average particle size, moisture, and the final temperature on the physicochemical properties of masa and tortillas elaborated from OHICF was evaluated and were compared with flour obtained by the ...

  4. Effect of composition on the polarization and ohmic resistances of ...

    Indian Academy of Sciences (India)

    2017-06-09

    Jun 9, 2017 ... Solid oxide fuel cell; composite cathodes; polarization resistance; ohmic resistance; ... of Oad on LSM, (iii) conversion of Oad into oxygen ion ... ions need to flow through the low temperature sintered ..... TPB's are present) suggest the formation of face-to-face con- ..... calculated using the following equation.

  5. Improved Ohmic-contact to AlGaN/GaN using Ohmic region recesses by self-terminating thermal oxidation assisted wet etching technique

    Science.gov (United States)

    Liu, J.; Wang, J.; Wang, H.; Zhu, L.; Wu, W.

    2017-06-01

    Lower Ti/Al/Ni/Au Ohmic contact resistance on AlGaN/GaN with wider rapid thermal annealing (RTA) temperature window was achieved using recessed Ohmic contact structure based on self-terminating thermal oxidation assisted wet etching technique (STOAWET), in comparison with conventional Ohmic contacts. Even at lower temperature such as 650°C, recessed structure by STOAWET could still obtain Ohmic contact with contact resistance of 1.97Ω·mm, while conventional Ohmic structure mainly featured as Schottky contact. Actually, both Ohmic contact recess and mesa isolation processes could be accomplished by STOAWET in one process step and the process window of STOAWET is wide, simplifying AlGaN/GaN HEMT device process. Our experiment shows that the isolation leakage current by STOAWET is about one order of magnitude lower than that by inductivity coupled plasma (ICP) performed on the same wafer.

  6. Design of a conductivity meter for highly insulating liquids

    Energy Technology Data Exchange (ETDEWEB)

    Medrano, M; Perez, A T; Soria-Hoyo, C [Dep. Electronica y Electromagnetismo, Facultad de Fisica, Universidad de Sevilla, Avda. Reina Mercedes s/n, 41012 Sevilla (Spain)

    2007-03-07

    The accurate measurement of the electrical conductivity of low conducting liquids is an important issue in many industrial applications. The lack of repeatability is a common problem to the available procedures and commercial techniques. In this paper, we present a device to measure the electrical conductivity of low conducting liquids. The variable inter-electrode gap allows us to assure the existence of an ohmic regime, since only under ohmic regime conditions is the value of the conductivity meaningful.

  7. Design of a conductivity meter for highly insulating liquids

    International Nuclear Information System (INIS)

    Medrano, M; Perez, A T; Soria-Hoyo, C

    2007-01-01

    The accurate measurement of the electrical conductivity of low conducting liquids is an important issue in many industrial applications. The lack of repeatability is a common problem to the available procedures and commercial techniques. In this paper, we present a device to measure the electrical conductivity of low conducting liquids. The variable inter-electrode gap allows us to assure the existence of an ohmic regime, since only under ohmic regime conditions is the value of the conductivity meaningful

  8. Investigation of the density turbulence in ohmic ASDEX plasmas

    International Nuclear Information System (INIS)

    Dodel, G.; Holtzhauer, E.

    1989-01-01

    A 119 μm homodyne laser scattering experiment is used on ASDEX to investigate wavenumber and frequency of the density fluctuations occuring in the different operational conditions of the machine. The changes of the density turbulence caused by additional heating are of primary interest with regard to a possible correlation to anomalous transport. Therefore, in the current experiment particular emphasis is placed on these investigations. On the other hand it is the ohmic phase which constitutes the least complicated physical situation in a tokamak and is therefore best suited to reveal the basic physical nature of the density turbulence. In the following we present a summary of our findings in the ohmic phase and make an attempt to compare these findings with what would be expected from the simplest model of density-gradient-driven driftwave turbulence saturated at the mixing-length level. (author) 3 refs., 4 figs

  9. Investigation of the density turbulence in ohmic ASDEX plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Dodel, G; Holtzhauer, E [Stuttgart Univ. (Germany, F.R.). Inst. fuer Plasmaforschung; Giannone, L.; Niedermeyer, H [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany, F.R.)

    1989-01-01

    A 119 {mu}m homodyne laser scattering experiment is used on ASDEX to investigate wavenumber and frequency of the density fluctuations occuring in the different operational conditions of the machine. The changes of the density turbulence caused by additional heating are of primary interest with regard to a possible correlation to anomalous transport. Therefore, in the current experiment particular emphasis is placed on these investigations. On the other hand it is the ohmic phase which constitutes the least complicated physical situation in a tokamak and is therefore best suited to reveal the basic physical nature of the density turbulence. In the following we present a summary of our findings in the ohmic phase and make an attempt to compare these findings with what would be expected from the simplest model of density-gradient-driven driftwave turbulence saturated at the mixing-length level. (author) 3 refs., 4 figs.

  10. The ohmic heating power supply for HL-1 tokamak

    International Nuclear Information System (INIS)

    Mingrui, Z.; Jiashun, C.

    1986-01-01

    A combination of capacitor banks, inductor and DC Fly wheel-Generator sets are used as ohmic heating power supply (OHPS) for HL-1, which is the largest tokamak in China. This system can give changeable waveform of current in a simple way, because of the use of protection for capacitor banks by changeable connection in easy way. Since the technology of forced zero current in the commutating breaker and synchronous self-triggering crowbar are used, the smooth conversion between the wave front provided by discharge of the capacitor banks and the flat top sustained by the inductor and flywheel realized. The performance of the system was tested by a dummy load and the system has been used in the HL-1 experiments. It is confirmed that this system is sufficiently available for the ohmic heating and has important effects on the long plasma lasting time on the order of 1 sec

  11. Transport and turbulence in TORE SUPRA ohmic discharges

    International Nuclear Information System (INIS)

    Garbet, X.; Payan, J.; Laviron, C.; Devynck, P.; Saha, S.K.; Capes, H.; Chen, X.P.; Coulon, J.P.; Gil, C.; Harris, G.; Hutter, T.; Pecquet, A.L.

    1992-01-01

    The mechanisms underlying the energy confinement behaviour in ohmic tokamak discharges are not yet understood. It is well known that the confinement time increases with the average density and saturates above a critical value of the density, but several explanations exist for this saturation. The present study is an analysis of a set of ohmic discharges in Tore Supra with I p =1.6 MA, B=4 T, R=2.35 m and a=0.78 m, where the average density was increased from 0.9 to 4.2 10 19 m -3 . For these plasma parameters, the energy confinement time given by magnetic measurements saturates for e > ≥ 2.5 10 19 m -3 . It is emphasized here that the onset of ionic turbulence is unlikely in Tore Supra. This conclusion relies on a transport analysis and turbulence measurements by CO 2 laser scattering, whose results are presented in this paper

  12. Parametric studies in ohmically heated plasmas in Heliotron E

    International Nuclear Information System (INIS)

    Mutoh, T.; Besshou, S.; Ijiri, Y.

    1983-01-01

    Parametric studies of volume averaged electron temperature and global electron energy confinement time /tau/epsilon /SUB e/ of ohmically heated Heliotron E plasmas have been performed using a data acquisition computer system. The scaling laws α (I /SUB OH/ x B/n /SUB e/) /SUP 1/2/ and /tau/epsilon /SUB e/ α n /SUP -1/2/ /SUB e/ x B/I /SUP 3/2/ /SUB OH/ are obtained directly by a code which fits the exponents of the plasma parameters ponents of the plasma parameters to the electron temperature and confinement time. The ohmically heated plasma confinement time /tau/epsilon /SUB e/ is shown to be related to the drift parameters xi (= V /SUB De/ /V /SUB Te/). The dependences of the energy confinement time on other plasma parameters is also presented. An investigation is made of the correlation between MHD activity and the confinement

  13. Effects of the ohmic current on collective scattering spectra

    International Nuclear Information System (INIS)

    Castiglioni, S.; Lontano, M.; Tartari, U.

    1993-01-01

    A numerical and analytical study of the modifications induced in the collective scattering spectra by the ohmic current governing the equilibrium magnetic configuration in toroidal plasmas is presented. The spectral density function is calculated assuming equilibrium distributions for the (bulk and impurity) ion species and a Spitzer-like distribution to describe the response of the electrons to the applied DC electric field. As expected, the spectral asymmetries can be non-negligibly enhanced in the region of the ion-acoustic frequency. They reach their maxima for tangential scattering geometries, where the magnetic effects on the spectra are negligible. This justifies the assumption of the non-magnetized spectra. A theoretically motivated potential is shown to exist for a more detailed experimental investigation of the feasibility of current-density measurements in ohmic plasmas, based on collective scattering. (author)

  14. Bias induced transition from an ohmic to a non-ohmic interface in supramolecular tunneling junctions with Ga2O3/EGaIn top electrodes.

    Science.gov (United States)

    Wimbush, Kim S; Fratila, Raluca M; Wang, Dandan; Qi, Dongchen; Liang, Cao; Yuan, Li; Yakovlev, Nikolai; Loh, Kian Ping; Reinhoudt, David N; Velders, Aldrik H; Nijhuis, Christian A

    2014-10-07

    This study describes that the current rectification ratio, R ≡ |J|(-2.0 V)/|J|(+2.0 V) for supramolecular tunneling junctions with a top-electrode of eutectic gallium indium (EGaIn) that contains a conductive thin (0.7 nm) supporting outer oxide layer (Ga2O3), increases by up to four orders of magnitude under an applied bias of >+1.0 V up to +2.5 V; these junctions did not change their electrical characteristics when biased in the voltage range of ±1.0 V. The increase in R is caused by the presence of water and ions in the supramolecular assemblies which react with the Ga2O3/EGaIn layer and increase the thickness of the Ga2O3 layer. This increase in the oxide thickness from 0.7 nm to ∼2.0 nm changed the nature of the monolayer-top-electrode contact from an ohmic to a non-ohmic contact. These results unambiguously expose the experimental conditions that allow for a safe bias window of ±1.0 V (the range of biases studies of charge transport using this technique are normally conducted) to investigate molecular effects in molecular electronic junctions with Ga2O3/EGaIn top-electrodes where electrochemical reactions are not significant. Our findings also show that the interpretation of data in studies involving applied biases of >1.0 V may be complicated by electrochemical side reactions which can be recognized by changes of the electrical characteristics as a function voltage cycling or in current retention experiments.

  15. Compound sawtooth study in ohmically heated TFTR plasmas

    International Nuclear Information System (INIS)

    Yamada, H.; McGuire, K.; Colchin, D.

    1985-09-01

    Compound sawtooth activity has been observed in ohmically heated, high current, high density TFTR plasmas. Commonly called ''double sawteeth,'' such sequences consist of a repetitive series of subordinate relaxations followed by a main relaxation with a different inversion radius. The period of such compound sawteeth can be as long as 100 msec. In other cases, however, no compound sawteeth or bursts of them can be observed in discharges with essentially the same parameters

  16. Statistical analyses of local transport coefficients in Ohmic ASDEX discharges

    International Nuclear Information System (INIS)

    Simmet, E.; Stroth, U.; Wagner, F.; Fahrbach, H.U.; Herrmann, W.; Kardaun, O.J.W.F.; Mayer, H.M.

    1991-01-01

    Tokamak energy transport is still an unsolved problem. Many theoretical models have been developed, which try to explain the anomalous high energy-transport coefficients. Up to now these models have been applied to global plasma parameters. A comparison of transport coefficients with global confinement time is only conclusive if the transport is dominated by one process across the plasma diameter. This, however, is not the case in most Ohmic confinement regimes, where at least three different transport mechanisms play an important role. Sawtooth activity leads to an increase in energy transport in the plasma centre. In the intermediate region turbulent transport is expected. Candidates here are drift waves and resistive fluid turbulences. At the edge, ballooning modes or rippling modes could dominate the transport. For the intermediate region, one can deduce theoretical scaling laws for τ E from turbulent theories. Predicted scalings reproduce the experimentally found density dependence of τ E in the linear Ohmic confinement regime (LOC) and the saturated regime (SOC), but they do not show the correct dependence on the isotope mass. The relevance of these transport theories can only be tested in comparing them to experimental local transport coefficients. To this purpose we have performed transport calculations on more than a hundred Ohmic ASDEX discharges. By Principal Component Analysis we determine the dimensionless components which dominate the transport coefficients and we compare the results to the predictions of various theories. (author) 6 refs., 2 figs., 1 tab

  17. Power balance in an Ohmically heated fusion reactor

    International Nuclear Information System (INIS)

    Christiansen, J.P.; Roberts, K.V.

    1982-01-01

    A simplified power-balance equation (zero-dimensional model) is used to study the performance of an Ohmically heated fusion reactor with emphasis on a pulsed reversed-field pinch concept (RFP). The energy confinement time tausub(E) is treated as an adjustable function, and empirical tokamak scaling laws are employed in the numerical estimates, which are supplemented by 1-D ATHENE code calculations. The known heating rates and energy losses are represented by the net energy replacement time tausub(W), which is exhibited as a surface in density (n) and temperature (T) space with a saddle point (nsub(*), Tsub(*)), the optimum ignition point. It is concluded that i) ignition by Ohmic heating is more practicable for the RFP reactor than for a tokamak reactor with the same tausub(E), (ii) if at fixed current the minor radius can be reduced or at fixed minor radius the current can be increased, then it is found that Ohmic ignition becomes more likely when present tokamak scaling laws are used. More definitive estimates require, however, a knowledge of tausub(E), which can only be obtained by establishing a reliable set of experimental RFP scaling laws and, in particular, by extending RFP experiments closer to the reactor regime. (author)

  18. Ohmic H-mode studies in TUMAN-3

    International Nuclear Information System (INIS)

    Lebedev, S.V.; Andrejko, M.V.; Askinazi, L.G.; Golant, V.E.; Kornev, V.A.; Levin, L.S.; Tukachinsky, A.S.; Tendler, M.

    1994-01-01

    The spontaneous transition from Ohmically heated limiter discharges into the regime with improved confinement termed as ''Ohmic H-mode'' has been investigated in ''TUMAN-3''. The typical signatures of H-mode in tokamaks with powerful auxiliary heating have been observed: sharp drop of D α radiation with simultaneous increase in the electron density and stored energy, suppression of the density fluctuations and establishing the steep gradient near the periphery. The crucial role of the radial electric field in the L-H transition was found in the experiments with boundary biasing. The possibility of initiating the H-mode using single pellet injection was demonstrated. In Ohmic H-mode strong dependencies of τ E on plasma current and on input power and weak dependence on density were found. Thermal energy confinement time enhanced by a factor of 10 compared to predictions of Neo-Alcator scaling. Longest energy confinement time (30 ms) was obtained in the small tokamak TUMAN-3. Absolute values of the energy confinement time are in agreement with scaling proposed for description of the ELM-free H-modes in devices with powerful auxiliary heating (''DIII-D/JET H-mode'' scaling). (author)

  19. Current-voltage curves of atomic-sized transition metal contacts: An explanation of why Au is ohmic and Pt is not

    DEFF Research Database (Denmark)

    Nielsen, S.K.; Brandbyge, Mads; Hansen, K.

    2002-01-01

    We present an experimental study of current-voltage (I-V) curves on atomic-sized Au and Pt contacts formed under cryogenic vacuum (4.2 K). Whereas I-V curves for Au are almost Ohmic, the conductance G=I/V for Pt decreases with increasing voltage, resulting in distinct nonlinear I-V behavior...

  20. Energy confinement scaling in tokamaks: some implications of recent experiments with ohmic and strong auxiliary heating

    International Nuclear Information System (INIS)

    Goldston, R.J.

    1984-02-01

    Recent results from confinement scaling experiments on tokamaks with ohmic and strong auxiliary heating are reviewed. An attempt is made to draw these results together into a low-density ohmic confinement scaling law, and a scaling law for confinement with auxiliary heating. The auxiliary heating confinement law may also serve to explain the saturation in tau/sub E/ vs anti n/sub e/ observed in some ohmic heating density scaling experiments

  1. Alternate ohmic heating coil arrangements for compact tokamak

    International Nuclear Information System (INIS)

    Dawson, J.W.; Moretti, A.; Stevens, H.C.; Thompson, K.

    1978-01-01

    The results for a number of ohmic heating (OH) coil arrangements which will allow the reduction of the major radius of Experimental Power Reactor (EPR) tokamaks will be given. In each case the results are compared, at least indirectly, to the reference case, which has the OH solenoid inside the central core of the reactor. The goal for the alternate geometries studied was to stay within the requirements imposed by the EPR conditions on the plasma and to produce as much or more OH V-s as the reference case

  2. Ohmic losses in coaxial resonators with longitudinal inner-outer corrugation

    Energy Technology Data Exchange (ETDEWEB)

    Shenyong Hou, A. [Terahertz Science and Technology Research Center, University of Electronics Science and Technology of China, Chengdu 610054 (China); Yangtze Normal University, Chongqing 408001 (China); Sheng Yu, B.; Hongfu Li, C.; Qixiang Zhao, D. [Terahertz Science and Technology Research Center, University of Electronics Science and Technology of China, Chengdu 610054 (China); Xiang Li, E. [Terahertz Science and Technology Research Center, University of Electronics Science and Technology of China, Chengdu 610054 (China); Queen Mary University of London, London E1 4NS (United Kingdom)

    2013-05-15

    In this paper, a coaxial resonator with longitudinal inner-outer corrugation is introduced. Its eigen-equation and expression of ohmic losses are derived. Ohmic losses in the cavity are investigated. Results show that ohmic losses in the outer and inner conductors share a similar variation trend, while the former is larger than the later. What's more, changes of the inner and outer slot depth and width induce different variations of ohmic losses on the surface of the inner and outer conductors.

  3. There's no place like Ohm: conduction in oxide thin films.

    Science.gov (United States)

    Scott, J F

    2014-04-09

    A pedagogical essay is given that alerts researchers to the errors inherent in assigning linear I(V) current-voltage dependences to Ohmic conduction. Such a linear I(V) is necessary but not sufficient, since other mechanisms, including Simmons' modification of the basic Schottky emission theory, also give linear I(V) at small applied voltages. Discrimination among Ohmic, Schottky, space-charge limited, and other models requires accurate thickness dependence I(d) data, where for Ohmic conduction I=a/d, whereas for interface-limited mechanisms such as Simmons/Schottky, I is nearly independent of d.

  4. Applicability of the lattice Boltzmann method to determine the ohmic resistance in equivalent resistor connections

    Science.gov (United States)

    Espinoza-Andaluz, Mayken; Barzola, Julio; Guarochico-Moreira, Víctor H.; Andersson, Martin

    2017-12-01

    Knowing the ohmic resistance in the materials allow to know in advance its electrical behavior when a potential difference is applied, and therefore the prediction of the electrical performance can be achieved in a most certain manner. Although the Lattice Boltzmann method (LBM) has been applied to solve several physical phenomena in complex geometries, it has only been used to describe the fluid phase, but applicability studies of LBM on the solid-electric-conducting material have not been carried out yet. The purpose of this paper is to demonstrate the accuracy of calculating the equivalent resistor connections using LBM. Several series and parallel resistor connections are effected. All the computations are carried out with 3D models, and the domain materials are designed by the authors.

  5. Magnetic Shear and Transport in ECRH Discharges of the TJ-II under Ohmic Induction

    Energy Technology Data Exchange (ETDEWEB)

    Lopez-Bruna, D.; Castejon, F.; Romero, J. A.; Estrada, T.; Medina, F.; Ochando, M.; Lopez-Fraguas, A.; Ascasibar, E.; Herranz, J.; Sanchez, E.; Luna, E. de la; Pastor, I.

    2006-07-01

    TJ-II is ha heliac type stellarator characterised by high, but almost constant, vacuum rotational transform throughout the confining volume. In ECRH plasmas, moderate induced ohmic currents (negligible heating and modification of the magnetic field nodules) are enough to disregard the bootstrap contribution, which allows us performing a fair calculation of the evolution of the rotational transform. We use the loop voltage diagnostic to estimate the plasma electrical conductivity. Then the evolution of the rotational transform and shear is related to changes in the profiles of electron and thermal diffusivities: negative shear correlates with decreasing diffusivities in the region of steepest density gradient; transport increases toward zero shear but the achieved positive values are too small to draw conclusions. The radial sweeping of lowest order rational magnetic surfaces does not determine the observed trends in transport. (Author)43 refs.

  6. Magnetic Shear and Transport in ECRH Discharges of the TJ-II under Ohmic Induction

    International Nuclear Information System (INIS)

    Lopez-Bruna, D.; Castejon, F.; Romero, J. A.; Estrada, T.; Medina, F.; Ochando, M.; Lopez-Fraguas, A.; Ascasibar, E.; Herranz, J.; Sanchez, E.; Luna, E. de la; Pastor, I.

    2006-01-01

    TJ-II is ha heliac type stellarator characterised by high, but almost constant, vacuum rotational transform throughout the confining volume. In ECRH plasmas, moderate induced ohmic currents (negligible heating and modification of the magnetic field nodules) are enough to disregard the bootstrap contribution, which allows us performing a fair calculation of the evolution of the rotational transform. We use the loop voltage diagnostic to estimate the plasma electrical conductivity. Then the evolution of the rotational transform and shear is related to changes in the profiles of electron and thermal diffusivities: negative shear correlates with decreasing diffusivities in the region of steepest density gradient; transport increases toward zero shear but the achieved positive values are too small to draw conclusions. The radial sweeping of lowest order rational magnetic surfaces does not determine the observed trends in transport. (Author)43 refs

  7. Ohmic H-mode and confinement in TCV

    International Nuclear Information System (INIS)

    Moret, J.-M.; Anton, M.; Barry, S.

    1995-01-01

    The unique flexibility of TCV for the creation of a wide variety of plasma shapes has been exploited to address some aspects of tokamak physics for which the shape may play an important role. The electron energy confinement time in limited ohmic L-mode plasmas whose elongation and triangularity have been varied (κ = 1.3 - 1.9, δ 0.1 - 0.7) has been observed to improve with elongation as κ 0.5 but to degrade with triangularity as (1 - 0.8 δ), for fixed safety factor. Ohmic H-modes have been obtained in several diverted and limited configurations, with some of the diverted discharges featuring large ELMs whose effects on the global confinement have been quantified. These effects depend on the configuration: in double null (DN) equilibria, a single ELM expels on average 2%, 6% and 2.5% of the particle, impurity and thermal energy content respectively, whilst in single null (SN) configurations, the corresponding numbers are 3.5%, 7% and 9%, indicative of larger ELM effects. The presence of absence of large ELMs in DN discharges has been actively controlled in a single discharge by alternately forcing one or other of the two X-points to lie on the separatrix, permitting stationary density and impurity content (Z eff ∼ 1.6) in long H-modes (1.5 s). (Author)

  8. Ohmic H-mode and confinement in TCV

    International Nuclear Information System (INIS)

    Moret, J.M.; Anton, M.; Barry, S.

    1995-01-01

    The unique flexibility of TCV for the creation of a wide variety of plasma shapes has been exploited to address some aspects of tokamak physics for which the shape may play an important role. The electron energy confinement time in limited ohmic L-mode plasmas whose elongation and triangularity have been varied, has been observed to improve with elongation as κ 0.5 but to degrade with triangularity as (1-0.8 δ), for fixed safety factor. Ohmic H-modes have been obtained in several diverted and limited configurations, with some of the diverted discharges featuring large ELMs whose effects on the global confinement have been quantified. These effects depend on the configuration: in double null (DN) equilibria, a single ELM expels on average 2%, 6% and 2.5% of the particle, impurity and thermal energy content respectively, whilst in single null (SN) configurations, the corresponding numbers are 3.5%, 7% and 9%, indicative of larger ELM effects. The presence or absence of large ELMs in DN discharges has been actively controlled in a single discharge by alternately forcing one or other of the two X-points to lie on the separatrix, permitting stationary density and impurity content (Z eff ≅1.6) in long H-modes (1.5 s). (author) 9 figs., 9 refs

  9. Hybrid polyketide synthases

    Energy Technology Data Exchange (ETDEWEB)

    Fortman, Jeffrey L.; Hagen, Andrew; Katz, Leonard; Keasling, Jay D.; Poust, Sean; Zhang, Jingwei; Zotchev, Sergey

    2016-05-10

    The present invention provides for a polyketide synthase (PKS) capable of synthesizing an even-chain or odd-chain diacid or lactam or diamine. The present invention also provides for a host cell comprising the PKS and when cultured produces the even-chain diacid, odd-chain diacid, or KAPA. The present invention also provides for a host cell comprising the PKS capable of synthesizing a pimelic acid or KAPA, and when cultured produces biotin.

  10. Dynamical determination of ohmic states of a cylindrical pinch

    International Nuclear Information System (INIS)

    Schnack, D.D.

    1980-04-01

    The dual problems of generation and sustainment of the reversed axial field are studied. It is shown that, if a cylindrical plasma is initially in an axisymmetric state with a sufficient degree of paramagnetism, field reversal can be attained by mode activity of a single helicity. The initial paramagnetism may be due to the method of pinch formation, as in fast experiments, or to a gradual altering of the pitch profile resulting from a succession of instabilities. Furthermore, if the total current is kept constant and energy loss and resistivity profiles are included in an ad hoc manner, one finds that the final steady state of the helical instability can be maintained for long times against resistive diffusion without the need for further unstable activity. These states, which possess zero order flow and possibly reversed axial field, represent steady equilibria which simultaneously satisfy force balance and Ohm's law, and are termed Ohmic states

  11. Modelling ohmic confinement experiments on the START tokamak

    International Nuclear Information System (INIS)

    Roach, C.M.

    1996-05-01

    Ohmic confinement data from the tight aspect ratio tokamak START has been analysed using the ASTRA transport simulation code. Neoclassical expressions have been modified to describe tight aspect ratio configurations, and the comparison between START data and models of anomalous transport has been made quantitative using the standard χ 2 test from statistics. Four confinement models (T11, Rebut-Lallia-Watkins, Lackner-Gottardi, and Taroni et al's Bohm model) have been compared with the START data. Three of the models are found to simulate START's electron temperature data moderately well, while Taroni et al's Bohm model overestimates electron temperatures in START by an order of magnitude. Thus comparison with START data tends to discriminate against Bohm models; these models are pessimistic or ITER. (author)

  12. Effect of Boronization on Ohmic Plasmas in NSTX

    International Nuclear Information System (INIS)

    Skinner, C.H.; Kugel, H.; Maingi, R.; Wampler, W.R.; Blanchard, W.; Bell, M.; Bell, R.; LeBlanc, B.; Gates, D.; Kaye, S.; LaMarche, P.; Menard, J.; Mueller, D.; Na, H.K.; Nishino, N.; Paul, S.; Sabbagh, S.; Soukhanovskii, V.

    2001-01-01

    Boronization of the National Spherical Torus Experiment (NSTX) has enabled access to higher density, higher confinement plasmas. A glow discharge with 4 mTorr helium and 10% deuterated trimethyl boron deposited 1.7 g of boron on the plasma facing surfaces. Ion beam analysis of witness coupons showed a B+C areal density of 10 to the 18 (B+C) cm to the -2 corresponding to a film thickness of 100 nm. Subsequent ohmic discharges showed oxygen emission lines reduced by x15, carbon emission reduced by two and copper reduced to undetectable levels. After boronization, the plasma current flattop time increased by 70% enabling access to higher density, higher confinement plasmas

  13. Ohmic heating of a spheromak to 100 eV

    Energy Technology Data Exchange (ETDEWEB)

    Jarboe, T.R.; Barnes, C.W.; Henins, I.; Hoida, H.W.; Knox, S.O.; Linford, R.K.; Sherwood, A.R.

    1984-01-01

    The first spheromaks with Thomson-scattering-measured electron temperatures of over 100 eV are described. The spheromak is generated by a magnetized coaxial plasma source in a background gas of 30 mTorr of H/sub 2/, and it is stably confined in an oblate 80 cm diam copper mesh flux conserver. The open mesh design allows rapid impurity transport out of the spheromak. The peak temperature, measured using multipoint Thomson scattering, is observed to rise from approximately 25 eV to over 100 eV in about 0.2 msec due to Ohmic heating from the decaying magnetic fields. Density (approx.5 x 10/sup 13/ cm/sup -3/) and magnetic fields (approximately 2 kG) are measured using interferometry and magnetic probes.

  14. Ohmic heating of a spheromak to 100 eV

    International Nuclear Information System (INIS)

    Jarboe, T.R.; Barnes, C.W.; Henins, I.; Hoida, H.W.; Knox, S.O.; Linford, R.K.; Sherwood, A.R.

    1984-01-01

    The first spheromaks with Thomson-scattering-measured electron temperatures of over 100 eV are described. The spheromak is generated by a magnetized coaxial plasma source in a background gas of 30 mTorr of H 2 , and it is stably confined in an oblate 80 cm diam copper mesh flux conserver. The open mesh design allows rapid impurity transport out of the spheromak. The peak temperature, measured using multipoint Thomson scattering, is observed to rise from approximately 25 eV to over 100 eV in about 0.2 msec due to Ohmic heating from the decaying magnetic fields. Density (approx.5 x 10 13 cm -3 ) and magnetic fields (approximately 2 kG) are measured using interferometry and magnetic probes

  15. Ultra-high-ohmic microstripline resistors for Coulomb blockade devices

    International Nuclear Information System (INIS)

    Lotkhov, Sergey V

    2013-01-01

    In this paper, we report on the fabrication and low-temperature characterization of ultra-high-ohmic microstripline resistors made of a thin film of weakly oxidized titanium. Nearly linear voltage–current characteristics were measured at temperatures down to T ∼ 20 mK for films with sheet resistivities as high as ∼7 kΩ, i.e. about an order of magnitude higher than our previous findings for weakly oxidized Cr. Our analysis indicates that such an improvement can help to create an advantageous high-impedance environment for different Coulomb blockade devices. Further properties of the Ti film addressed in this work show the promise of low-noise behavior of the resistors when applied in different realizations of the quantum standard of current. (paper)

  16. New fast switches for the Tore Supra ohmic heating circuit

    International Nuclear Information System (INIS)

    Zunino, K.; Bruneth, J.; Cara, P.; Louart, A.; Santagiustina, A.; Emelyanova, I.; Filippov, F.; Mikailov, N.

    2003-01-01

    The Tore-Supra ohmic heating circuit is equipped with four fast make switches and one fast opening switch. After many years of operation, it became necessary to substitute this equipment by modern components with similar ratings. An extensive research has been undertaken to find fast switches able to withstand more than 2500 operations per year without maintenance, at a make current of 54 kA, a voltage of 12 kV and with a closing time of less than 15 ms. At the end of the investigation, it was decided to replace the old components by fast mechanical switches proposed by the Efremov Institute and based on a prototype developed for ITER. This paper presents the technical requirements and the characteristics of the switches and describes the operational experience gained with these components during operating campaigns of 2002 and 2003. (authors)

  17. An ohmic heating circuit for the CASTOR tokamak

    International Nuclear Information System (INIS)

    Valovic, M.

    1989-07-01

    To extend the duration of the CASTOR tokamak discharge to the limit given by the toroidal magnetic field pulse, a simple ohmic heating circuit is proposed. It exploits two condenser banks charged to different voltages and switched by means of an ignitron switch. The circuit parameters are chosen so as to achieve optimum current ramp-up and flat-top phases. The choice of parameters was checked using a simple computer code, with the nonlinear magnetization of the transformer core being taken into account. The results of calculation are compared with those of an experimental test shot with a discharge current and duration of 19 kA and 40 ms, respectively. (J.U.). 3 figs., 4 refs

  18. An Arabidopsis callose synthase

    DEFF Research Database (Denmark)

    Ostergaard, Lars; Petersen, Morten; Mattsson, Ole

    2002-01-01

    in the Arabidopsis mpk4 mutant which exhibits systemic acquired resistance (SAR), elevated beta-1,3-glucan synthase activity, and increased callose levels. In addition, AtGsl5 is a likely target of salicylic acid (SA)-dependent SAR, since AtGsl5 mRNA accumulation is induced by SA in wild-type plants, while...... expression of the nahG salicylate hydroxylase reduces AtGsl5 mRNA levels in the mpk4 mutant. These results indicate that AtGsl5 is likely involved in callose synthesis in flowering tissues and in the mpk4 mutant....

  19. Monoterpene synthases from common sage (Salvia officinalis)

    Energy Technology Data Exchange (ETDEWEB)

    Croteau, Rodney Bruce (Pullman, WA); Wise, Mitchell Lynn (Pullman, WA); Katahira, Eva Joy (Pullman, WA); Savage, Thomas Jonathan (Christchurch 5, NZ)

    1999-01-01

    cDNAs encoding (+)-bornyl diphosphate synthase, 1,8-cineole synthase and (+)-sabinene synthase from common sage (Salvia officinalis) have been isolated and sequenced, and the corresponding amino acid sequences has been determined. Accordingly, isolated DNA sequences (SEQ ID No:1; SEQ ID No:3 and SEQ ID No:5) are provided which code for the expression of (+)-bornyl diphosphate synthase (SEQ ID No:2), 1,8-cineole synthase (SEQ ID No:4) and (+)-sabinene synthase SEQ ID No:6), respectively, from sage (Salvia officinalis). In other aspects, replicable recombinant cloning vehicles are provided which code for (+)-bornyl diphosphate synthase, 1,8-cineole synthase or (+)-sabinene synthase, or for a base sequence sufficiently complementary to at least a portion of (+)-bornyl diphosphate synthase, 1,8-cineole synthase or (+)-sabinene synthase DNA or RNA to enable hybridization therewith. In yet other aspects, modified host cells are provided that have been transformed, transfected, infected and/or injected with a recombinant cloning vehicle and/or DNA sequence encoding (+)-bornyl diphosphate synthase, 1,8-cineole synthase or (+)-sabinene synthase. Thus, systems and methods are provided for the recombinant expression of the aforementioned recombinant monoterpene synthases that may be used to facilitate their production, isolation and purification in significant amounts. Recombinant (+)-bornyl diphosphate synthase, 1,8-cineole synthase and (+)-sabinene synthase may be used to obtain expression or enhanced expression of (+)-bornyl diphosphate synthase, 1,8-cineole synthase and (+)-sabinene synthase in plants in order to enhance the production of monoterpenoids, or may be otherwise employed for the regulation or expression of (+)-bornyl diphosphate synthase, 1,8-cineole synthase and (+)-sabinene synthase, or the production of their products.

  20. Dual ohmic contact to N- and P-type silicon carbide

    Science.gov (United States)

    Okojie, Robert S. (Inventor)

    2013-01-01

    Simultaneous formation of electrical ohmic contacts to silicon carbide (SiC) semiconductor having donor and acceptor impurities (n- and p-type doping, respectively) is disclosed. The innovation provides for ohmic contacts formed on SiC layers having n- and p-doping at one process step during the fabrication of the semiconductor device. Further, the innovation provides a non-discriminatory, universal ohmic contact to both n- and p-type SiC, enhancing reliability of the specific contact resistivity when operated at temperatures in excess of 600.degree. C.

  1. Ohmic cooking of whole beef muscle--evaluation of the impact of a novel rapid ohmic cooking method on product quality.

    Science.gov (United States)

    Zell, Markus; Lyng, James G; Cronin, Denis A; Morgan, Desmond J

    2010-10-01

    Cylindrical cores of beef semitendinosus (500g) were cooked in a combined ohmic/convection heating system to low (72 degrees C, LTLT) and high (95 degrees C, HTST) target end-point temperatures. A control was also cooked to an end-point temperature of 72 degrees C at the coldest point. Microbial challenge studies on a model meat matrix confirmed product safety. Hunter L-values showed that ohmically heated meat had significantly (pHTST)) relative to the control (56.85). No significant texture differences (p>/=0.05) were suggested by Warner-Bratzler peak load values (34.09, 36.37 vs. 35.19N). Cook loss was significantly (pHTST and the control were more comparable (6.09 and 7.71, respectively). These results demonstrate considerable potential for this application of ohmic heating for whole meats. Copyright (c) 2010 The American Meat Science Association. Published by Elsevier Ltd. All rights reserved.

  2. Turbulence and energy confinement in TORE SUPRA ohmic discharges

    International Nuclear Information System (INIS)

    Garbet, X.; Payan, J.; Laviron, C.; Devynck, P.; Saha, S.K.; Capes, H.; Chen, X.P.; Coulon, J.P.; Gil, C.; Harris, G.; Hutter, T.; Pecquet, A.L.

    1992-06-01

    Results on confinement and turbulence from a set of ohmic discharges in Tore Supra are discussed. The attention is focused on the saturation of the energy confinement time and it is emphasized that this saturation could be explained by a saturation of the electron heat diffusivity. Ion behaviour is indeed governed by dilution and equipartition effects. Although the ion heat transport is never neoclassical, there is no enhanced degradation at the saturation. This behaviour is confirmed by turbulence measurements given by CO 2 laser coherent scattering. The density fluctuations level follows the electron heat diffusivity variations with the average density. Waves propagating in the ion diamagnetic direction are always present in turbulence frequency spectra. Thus, the saturation cannot be explained by the onset of an ion turbulence. The existence of an ion turbulence at the edge at all densities cannot be excluded. However, this ion feature in scattering spectra could be explained by a Doppler shift associated to an inversion point of the radial electric field at the edge

  3. Desgn of a 20-MJ superconducting ohmic-heating coil

    International Nuclear Information System (INIS)

    Singh, S.K.; Murphy, J.H.; Janocko, M.A.; Haller, H.E.; Litz, D.C.; Eckels, P.W.; Rogers, J.D.; Thullen, P.

    1979-01-01

    Conceptual designs of 20-MJ superconducting coils which were developed to demonstrate the feasibility of an ohmic-heating system were discussed. The superconductor materials were NbTi and Nb 3 Sn for the pool boil and forced-flow cooling, respectively. The coils were designed to be cryostable for bipolar operation from +7 to -7 tesla maximum field within one second. The structural design addresses the distribution of structure and structural materials used in the pulsed field environment. The cyclic stresses anticipated and the fatigue limits of the structural materials were examined in view of the operating life of the coil. The coils were designed to generate the flux swings while simultaneously meeting the limitations imposed by cooling, insulation, current density and the stresses in the materials. Both the pool and forced cooled conductors have the same criterion for cryostability, i.e., the conductor must return to the superconducting state from an initial temperature of 20 0 K while the full transport current is flowing through the conductor

  4. Ohmic metallization technology for wide band-gap semiconductors

    International Nuclear Information System (INIS)

    Iliadis, A.A.; Vispute, R.D.; Venkatesan, T.; Jones, K.A.

    2002-01-01

    Ohmic contact metallizations on p-type 6H-SiC and n-type ZnO using a novel approach of focused ion beam (FIB) surface-modification and direct-write metal deposition will be reviewed, and the properties of such focused ion beam assisted non-annealed contacts will be reported. The process uses a Ga focused ion beam to modify the surface of the semiconductor with different doses, and then introduces an organometallic compound in the Ga ion beam, to effect the direct-write deposition of a metal on the modified surface. Contact resistance measurements by the transmission line method produced values in the low 10 -4 Ω cm 2 range for surface-modified and direct-write Pt and W non-annealed contacts, and mid 10 -5 Ω cm 2 range for surface-modified and pulse laser deposited TiN contacts. An optimum Ga surface-modification dosage window is determined, within which the current transport mechanism of these contacts was found to proceed mainly by tunneling through the metal-modified-semiconductor interface layer

  5. Analysis of a global energy confinement database for JET ohmic plasmas

    International Nuclear Information System (INIS)

    Bracco, G.; Thomsen, K.

    1997-01-01

    A database containing global energy confinement data for JET ohmic plasmas in the campaigns from 1984 to 1992 has been established. An analysis is presented of this database and the results are compared with data from other tokamaks, such as the Axially Symmetric Divertor Experiment (ASDEX), Frascati Tokamak Upgrade (FTU) and Tore Supra. The trends of JET ohmic confinement appear to be similar to those observed on other tokamaks: a linear dependence of the global energy confinement time on density is observed up to a density value where a saturation is attained; this density value defines the border between the linear and the saturated ohmic confinement regimes; this border is shifted towards higher density values if the q value of the discharge is decreased; the global confinement time in the saturated ohmic regime increases less than linearly with the value of the magnetic field. (author). 20 refs, 13 figs, 4 tabs

  6. Ohmic Heating Technology and Its Application in Meaty Food: A Review

    OpenAIRE

    Rishi Richa; N. C. Shahi; Anupama Singh; U. C. Lohani; P. K. Omre; Anil Kumar; T. K. Bhattacharya

    2017-01-01

    The purpose of the current review paper is to investigate and analyze about the effects of ohmic heating (OH) different application in the field of fish, meat and its product and compare it with other conventional thermal methods of food processing such as thawing, heating, cooking etc. Food quality, food safety, convenience, freshness, healthy food, natural flavor and taste with extended shelf-life are the main criteria for the demand made by today’s consumers. Ohmic heating is a substitute ...

  7. Effects of Ohmic Heating on Microbial Counts and Denaturatiuon of Proteins in Milk

    OpenAIRE

    SUN, Huixian; KAWAMURA, Shuso; HIMOTO, Jun-ichi; ITOH, Kazuhiko; WADA, Tatsuhiko; KIMURA, Toshinori

    2008-01-01

    The aim of this study was to compare the inactivation effects of ohmic heating (internal heating by electric current) and conventional heating (external heating by hot water) on viable aerobes and Streptococcus thermophilus 2646 in milk under identical temperature history conditions. The effects of the two treatments on quality of milk were also compared by assessing degrees of protein denaturation in raw and sterilized milk (raw milk being sterilized by ohmic heating or conventional heating)...

  8. Effects of thin heavily Mg-doped GaN capping layer on ohmic contact formation of p-type GaN

    International Nuclear Information System (INIS)

    Wu, L L; Zhao, D G; Jiang, D S; Chen, P; Le, L C; Li, L; Liu, Z S; Zhang, S M; Zhu, J J; Wang, H; Zhang, B S; Yang, H

    2013-01-01

    The growth condition of thin heavily Mg-doped GaN capping layer and its effect on ohmic contact formation of p-type GaN were investigated. It is confirmed that the excessive Mg doping can effectively enhance the Ni/Au contact to p-GaN after annealing at 550 °C. When the flow rate ratio between Mg and Ga gas sources is 6.4% and the layer width is 25 nm, the capping layer grown at 850 °C exhibits the best ohmic contact properties with respect to the specific contact resistivity (ρ c ). This temperature is much lower than the conventional growth temperature of Mg-doped GaN, suggesting that the deep-level-defect induced band may play an important role in the conduction of capping layer. (paper)

  9. A thermal transport coefficient for ohmic and ICRF plasmas in alcator C-mode

    International Nuclear Information System (INIS)

    Daughton, W.; Coppi, B.; Greenwald, M.

    1996-01-01

    The energy confinement in plasmas produced by Alcator C-Mod machine is markedly different from that observed by previous high field compact machines such as Alcator A and C, FT, and more recently FTU. For ohmic plasmas at low and moderate densities, the confinement times routinely exceed those expected from the so-called open-quotes neo-Alcatorclose quotes scaling by a factor as high as three. For both ohmic and ICRF heated plasmas, the energy confinement time increases with the current and is approximately independent of the density. The similarity in the confinement between the ohmic and ICRF regimes opens the possibility that the thermal transport in Alcator C-Mod may be described by one transport coefficient for both regimes. We introduce a modified form of a transport coefficient previously used to describe ohmic plasmas in Alcator C-Mod. The coefficient is inspired by the properties of the so-called open-quotes ubiquitousclose quotes mode that can be excited in the presence of a significant fraction of trapped electrons and also includes the constraint of profile consistency. A detailed series of transport simulations are used to show that the proposed coefficient can reproduce the observed temperature profiles, loop voltage and energy confinement time for both ohmic and ICRF discharges. A total of nearly two dozen ohmic and ICRF Alcator C-Mod discharges have been fit over the range of parameter space available using this transport coefficient

  10. Effects of plasma treatment on the Ohmic characteristics of Ti/Al/Ti/Au contacts to n-AlGaN

    International Nuclear Information System (INIS)

    Cao, X. A.; Piao, H.; LeBoeuf, S. F.; Li, J.; Lin, J. Y.; Jiang, H. X.

    2006-01-01

    The effects of surface treatment using Cl 2 /BCl 3 and Ar inductive coupled plasmas on the Ohmic characteristics of Ti/Al/Ti/Au contacts to n-type Al x Ga 1-x N (x=0-0.5) were investigated. Plasma treatment significantly increased the surface conductivity of GaN and Al 0.1 Ga 0.9 N, leading to improved Ohmic behaviors of the contacts. However, it reduced the surface doping level in Al x Ga 1-x N (x≥0.3) and degraded the contact properties. Following a 900-1000 deg. C anneal, the Ti/Al/Ti/Au contacts to Al x Ga 1-x N (x=0-0.3) became truly Ohmic, with specific contact resistances of (3-7)x10 -5 Ω cm 2 , whereas the contact to Al 0.5 Ga 0.5 N remained rectifying even without the plasma treatment. X-ray photoelectron spectroscopy measurements confirmed that the Fermi level moved toward the conduction band in GaN after the plasma treatment, but it was pinned by plasma-induced deep-level states in Al 0.5 Ga 0.5 N. This study emphasizes the need to mitigate plasma damage introduced during the mesa etch step for AlGaN-based deep-UV emitters and detectors

  11. There’s no place like Ohm: conduction in oxide thin films

    International Nuclear Information System (INIS)

    Scott, J F

    2014-01-01

    A pedagogical essay is given that alerts researchers to the errors inherent in assigning linear I(V) current–voltage dependences to Ohmic conduction. Such a linear I(V) is necessary but not sufficient, since other mechanisms, including Simmons’ modification of the basic Schottky emission theory, also give linear I(V) at small applied voltages. Discrimination among Ohmic, Schottky, space-charge limited, and other models requires accurate thickness dependence I(d) data, where for Ohmic conduction I = a/d, whereas for interface-limited mechanisms such as Simmons/Schottky, I is nearly independent of d. (fast track communications)

  12. Electron quantum interferences and universal conductance fluctuations

    International Nuclear Information System (INIS)

    Benoit, A.; Pichard, J.L.

    1988-05-01

    Quantum interferences yield corrections to the classical ohmic behaviour predicted by Boltzmann theory in electronic transport: for instance the well-known ''weak localization'' effects. Furthermore, very recently, quantum interference effects have been proved to be responsible for statistically different phenomena, associated with Universal Conductance Fluctuations and observed on very small devices [fr

  13. Hopping Conductivity Enhanced by Microwave Radiation

    International Nuclear Information System (INIS)

    Ovadyahu, Z

    2012-01-01

    Hopping conductivity is enhanced when exposed to microwave (MW) fields. Data taken on several Anderson-localized systems and granular-aluminium are presented to illustrate the generality of the phenomenon. It is suggested that the effect is due to a field-enhanced hopping, which is the ac version of a non-ohmic effect familiar from studies in the dc transport regime.

  14. Optimization of ohmic heating parameters for polyphenoloxidase inactivation in not-from-concentrate elstar apple juice using RSM

    DEFF Research Database (Denmark)

    Abedelmaksoud, Tarek; Mohsen, Sobhy Mohamed; Duedahl-Olesen, Lene

    2018-01-01

    In this study, optimization of ohmic heating (OH) process parameters (temperature and voltage gradient) to inactivate polyphenoloxidase (PPO) of not-from-concentrate (NFC) apple juice was conducted. Response surface methodology was used for optimization of OH parameters, where the voltage gradient...... and temperature on the PPO activity in the NFC apple juice was evaluated. Then the optimized condition was used to produce the NFC apple juice and the quality parameters were evaluated and compared to NFC apple juice prepared by conventional heating (CH). The studied parameters were: PPO activity, total phenolic......, total carotenoids, ascorbic acid, cloud value, color as well as physical properties (i.e., TSS, acidity, electric conductivity and viscosity). The reduction of PPO activities was 97 and 91% for OH (at 40 V/cm and 80 °C) and CH (at 90 °C and 60 s), respectively. The reduction of the ascorbic acid...

  15. Enhanced piezoelectric output voltage and Ohmic behavior in Cr-doped ZnO nanorods

    International Nuclear Information System (INIS)

    Sinha, Nidhi; Ray, Geeta; Godara, Sanjay; Gupta, Manoj K.; Kumar, Binay

    2014-01-01

    Highlights: • Low cost highly crystalline Cr-doped ZnO nanorods were synthesized. • Enhancement in dielectric, piezoelectric and ferroelectric properties were observed. • A high output voltage was obtained in AFM. • Cr-doping resulted in enhanced conductivity and better Ohmic behavior in ZnO/Ag contact. - Abstract: Highly crystalline Cr-doped ZnO nanorods (NRs) were synthesized by solution technique. The size distribution was analyzed by high resolution tunneling electron microscope (HRTEM) and particle size analyzer. In atomic force microscope (AFM) studies, peak to peak 8 mV output voltage was obtained on the application of constant normal force of 25 nN. It showed high dielectric constant (980) with phase transition at 69 °C. Polarization vs. electric field (P–E) loops with remnant polarization (6.18 μC/cm 2 ) and coercive field (0.96 kV/cm) were obtained. In I–V studies, Cr-doping was found to reduce the rectifying behavior in the Ag/ZnO Schottky contact which is useful for field effect transistor (FET) and solar cell applications. With these excellent properties, Cr-doped ZnO NRs can be used in nanopiezoelectronics, charge storage and ferroelectric applications

  16. Effect of electropermeabilization by ohmic heating for inactivation of Escherichia coli O157:H7, Salmonella enterica serovar Typhimurium, and Listeria monocytogenes in buffered peptone water and apple juice.

    Science.gov (United States)

    Park, Il-Kyu; Kang, Dong-Hyun

    2013-12-01

    The effect of electric field-induced ohmic heating for inactivation of Escherichia coli O157:H7, Salmonella enterica serovar Typhimurium, and Listeria monocytogenes in buffered peptone water (BPW) (pH 7.2) and apple juice (pH 3.5; 11.8 °Brix) was investigated in this study. BPW and apple juice were treated at different temperatures (55°C, 58°C, and 60°C) and for different times (0, 10, 20, 25, and 30 s) by ohmic heating compared with conventional heating. The electric field strength was fixed at 30 V/cm and 60 V/cm for BPW and apple juice, respectively. Bacterial reduction resulting from ohmic heating was significantly different (Pheating at 58°C and 60°C in BPW and at 55°C, 58°C, and 60°C in apple juice for intervals of 0, 10, 20, 25, and 30 s. These results show that electric field-induced ohmic heating led to additional bacterial inactivation at sublethal temperatures. Transmission electron microscopy (TEM) observations and the propidium iodide (PI) uptake test were conducted after treatment at 60°C for 0, 10, 20, 25 and 30 s in BPW to observe the effects on cell permeability due to electroporation-caused cell damage. PI values when ohmic and conventional heating were compared were significantly different (Pheating can more effectively reduce bacterial populations at reduced temperatures and shorter time intervals, especially in acidic fruit juices such as apple juice. Therefore, loss of quality can be minimized in a pasteurization process incorporating ohmic heating.

  17. Energy confinement in Ohmic H-mode in TUMAN-3M

    International Nuclear Information System (INIS)

    Andrejko, M.V.; Askinazi, L.G.; Golant, V.E.; Kornev, V.A.; Lebedev, S.V.; Levin, L.S.; Tukachinsky, A.S.

    1997-01-01

    The spontaneous transition from Ohmically heated limiter discharges into the regime with improved confinement termed as ''Ohmic H-mode'' has been investigated in ''TUMAN-3''. The typical signatures of H-mode in tokamaks with powerful auxiliary heating have been observed: sharp drop of D α radiation with simultaneous increase in the electron density and stored energy, suppression of the density fluctuations and establishing the steep gradient near the periphery. In 1994 new vacuum vessel had been installed in TUMAN-3 tokamak. The vessel has the same sizes as old one (R 0 =0.55 m, a 1 =0.24 m). New vessel was designed to reduce mechanical stresses in the walls during B T ramp phase of a shot. Therefore modified device - TUMAN-3M is able to produce higher B T and I p , up to 2 T and 0.2 MA respectively. During first experimental run device was operated in Ohmic Regime. In these experiments the possibility to achieve Ohmic H-mode was studied. The study of the parametric dependencies of the energy confinement time in both OH and Ohmic H-mode was performed. In Ohmic H-mode strong dependencies of τ E on plasma current and on input power and weak dependence on density were found. Energy confinement time in TUMAN-3/TUMAN-3M Ohmic H-mode has revealed good agreement with JET/DIII-D/ASDEX scaling for ELM-free H-mode, resulting in very long τ E at the high plasma current discharges. (author)

  18. A variational master equation approach to quantum dynamics with off-diagonal coupling in a sub-Ohmic environment

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Ke-Wei [School of Science, Hangzhou Dianzi University, Hangzhou 310018 (China); Division of Materials Science, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore); Fujihashi, Yuta; Ishizaki, Akihito [Institute for Molecular Science, National Institutes of Natural Sciences, Okazaki 444-8585 (Japan); Zhao, Yang, E-mail: YZhao@ntu.edu.sg [Division of Materials Science, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore)

    2016-05-28

    A master equation approach based on an optimized polaron transformation is adopted for dynamics simulation with simultaneous diagonal and off-diagonal spin-boson coupling. Two types of bath spectral density functions are considered, the Ohmic and the sub-Ohmic. The off-diagonal coupling leads asymptotically to a thermal equilibrium with a nonzero population difference P{sub z}(t → ∞) ≠ 0, which implies localization of the system, and it also plays a role in restraining coherent dynamics for the sub-Ohmic case. Since the new method can extend to the stronger coupling regime, we can investigate the coherent-incoherent transition in the sub-Ohmic environment. Relevant phase diagrams are obtained for different temperatures. It is found that the sub-Ohmic environment allows coherent dynamics at a higher temperature than the Ohmic environment.

  19. Study of Ti/Si/Ti/Al/Ni/Au ohmic contact for AlGaN/GaN HEMT

    Science.gov (United States)

    Shostachenko, S. A.; Porokhonko, Y. A.; Zakharchenko, R. V.; Burdykin, M. S.; Ryzhuk, R. V.; Kargin, N. I.; Kalinin, B. V.; Belov, A. A.; Vasiliev, A. N.

    2017-12-01

    This paper is dedicated to the experimental investigation of Ohmic contacts to the n+-doped region of AlGaN/GaN transistor heterostructure based on Ti/Si/Ti/Al/Ni/Au metallization. Effect of annealing temperature on the specific resistance of Ohmic contact was studied. Ohmic contact with the resistance of 3.4·10-6 Ω·cm2 was formed by optimization of the annealing temperature and introduction of the additional doping silicon layer.

  20. Effects of combined gate and ohmic recess on GaN HEMTs

    Directory of Open Access Journals (Sweden)

    Sunil Kumar

    2016-09-01

    Full Text Available AlGaN/GaN, because of their superior material properties, are most suitable semiconductor material for High Electron Mobility Transistors (HEMTs. In this work we investigated the hidden physics behind these materials and studied the effect of recess technology in AlGaN/GaN HEMTs. The device under investigation is simulated for different recess depth using Silvaco-Atlas TCAD. Recess technology improves the performance of AlGaN/GaN HEMTs. We considered three kinds of recess technology gate, ohmic and combination of gate and ohmic. Gate recess improves transconductance gm but it reduces the drain current Id of the device under investigation. Ohmic recess improves the transconductance gm but it introduces leakage current Ig in the device. In order to use AlGaN/GaN for high voltage operation, both the transconductance and the drain current should be reasonably high which is obtained by combining both gate and ohmic recess technologies. A good balance in transconductance and drain current is achieved by combining both gate and ohmic recess technologies without any leakage current.

  1. Effect of ohmic heating processing conditions on color stability of fungal pigments.

    Science.gov (United States)

    Aguilar-Machado, Diederich; Morales-Oyervides, Lourdes; Contreras-Esquivel, Juan C; Aguilar, Cristóbal; Méndez-Zavala, Alejandro; Raso, Javier; Montañez, Julio

    2017-06-01

    The aim of this work was to analyze the effect of ohmic heating processing conditions on the color stability of a red pigment extract produced by Penicillium purpurogenum GH2 suspended in a buffer solution (pH 6) and in a beverage model system (pH 4). Color stability of pigmented extract was evaluated in the range of 60-90 ℃. The degradation pattern of pigments was well described by the first-order (fractional conversion) and Bigelow model. Degradation rate constants ranged between 0.009 and 0.088 min -1 in systems evaluated. Significant differences in the rate constant values of the ohmic heating-treated samples in comparison with conventional thermal treatment suggested a possible effect of the oscillating electric field generated during ohmic heating. The thermodynamic analysis also indicated differences in the color degradation mechanism during ohmic heating specifically when the pigment was suspended in the beverage model system. In general, red pigments produced by P. purpurogenum GH2 presented good thermal stability under the range of the evaluated experimental conditions, showing potential future applications in pasteurized food matrices using ohmic heating treatment.

  2. Apple snack enriched with L-arginine using vacuum impregnation/ohmic heating technology.

    Science.gov (United States)

    Moreno, Jorge; Echeverria, Julian; Silva, Andrea; Escudero, Andrea; Petzold, Guillermo; Mella, Karla; Escudero, Carlos

    2017-07-01

    Modern life has created a high demand for functional food, and in this context, emerging technologies such as vacuum impregnation and ohmic heating have been applied to generate functional foods. The aim of this research was to enrich the content of the semi-essential amino acid L-arginine in apple cubes using vacuum impregnation, conventional heating, and ohmic heating. Additionally, combined vacuum impregnation/conventional heating and vacuum impregnation/ohmic heating treatments were evaluated. The above treatments were applied at 30, 40 and 50  ℃ and combined with air-drying at 40 ℃ in order to obtain an apple snack rich in L-arginine. Both the impregnation kinetics of L-arginine and sample color were evaluated. The impregnated samples created using vacuum impregnation/ohmic heating at 50 ℃ presented a high content of L-arginine, an effect attributed primarily to electropermeabilization. Overall, vacuum impregnation/ohmic heating treatment at 50 ℃, followed by drying at 40 ℃, was the best process for obtaining an apple snack rich in L-arginine.

  3. Ohmic contacts on n-type β-Ga2O3 using AZO/Ti/Au

    Directory of Open Access Journals (Sweden)

    Patrick H. Carey IV

    2017-09-01

    Full Text Available AZO interlayers between n-Ga2O3 and Ti/Au metallization significantly enhance Ohmic contact formation after annealing at ≥ 300°C. Without the presence of the AZO, similar anneals produce only rectifying current-voltage characteristics. Transmission Line Measurements of the Au/Ti/AZO/Ga2O3 stacks showed the specific contact resistance and transfer resistance decreased sharply from as-deposited values with annealing. The minimum contact resistance and specific contact resistance of 0.42 Ω-mm and 2.82 × 10-5 Ω-cm2 were achieved after a relatively low temperature 400°C annealing. The conduction band offset between AZO and Ga2O3 is 0.79 eV and provides a favorable pathway for improved electron transport across this interface.

  4. Ohmic contacts on n-type β-Ga2O3 using AZO/Ti/Au

    Science.gov (United States)

    Carey, Patrick H.; Yang, Jiancheng; Ren, F.; Hays, David C.; Pearton, S. J.; Jang, Soohwan; Kuramata, Akito; Kravchenko, Ivan I.

    2017-09-01

    AZO interlayers between n-Ga2O3 and Ti/Au metallization significantly enhance Ohmic contact formation after annealing at ≥ 30 0°C. Without the presence of the AZO, similar anneals produce only rectifying current-voltage characteristics. Transmission Line Measurements of the Au/Ti/AZO/Ga2O3 stacks showed the specific contact resistance and transfer resistance decreased sharply from as-deposited values with annealing. The minimum contact resistance and specific contact resistance of 0.42 Ω-mm and 2.82 × 10-5 Ω-cm2 were achieved after a relatively low temperature 40 0°C annealing. The conduction band offset between AZO and Ga2O3 is 0.79 eV and provides a favorable pathway for improved electron transport across this interface.

  5. An investigation on the application of ohmic heating of cold water shrimp and brine mixtures

    DEFF Research Database (Denmark)

    Pedersen, Søren Juhl; Feyissa, Aberham Hailu; Brøkner Kavli, Sissel Therese

    2016-01-01

    Cooking is an important unit-operation in the production of cooked and peeled shrimps. The present study explores the feasibility of using ohmic heating for cooking of shrimps. The focus is on investigating the effects of different process parameters on heating time and quality of ohmic cooked...... shrimps (Pandalus Borelias). The shrimps were heated to a core temperature of 72 °C in a brine solution using a small batch ohmic heater. Three experiments were performed: 1) a comparative analyses of the temperature development between different sizes of shrimps and thickness (head and tail region...... of the shrimp) over varying salt concentrations (10 kg m−3 to 20 kg m−3) and electric field strengths (1150 V m−1 to 1725 V m−1) with the heating time as the response; 2) a 2 level factorial experiment for screening the impact of processing conditions using electric field strengths of 1250 V m−1 and 1580 V m−1...

  6. Minimization of Ohmic Losses for Domain Wall Motion in a Ferromagnetic Nanowire

    Science.gov (United States)

    Tretiakov, O. A.; Liu, Y.; Abanov, Ar.

    2010-11-01

    We study current-induced domain-wall motion in a narrow ferromagnetic wire. We propose a way to move domain walls with a resonant time-dependent current which dramatically decreases the Ohmic losses in the wire and allows driving of the domain wall with higher speed without burning the wire. For any domain-wall velocity we find the time dependence of the current needed to minimize the Ohmic losses. Below a critical domain-wall velocity specified by the parameters of the wire the minimal Ohmic losses are achieved by dc current. Furthermore, we identify the wire parameters for which the losses reduction from its dc value is the most dramatic.

  7. Minimization of Ohmic losses for domain wall motion in ferromagnetic nanowires

    Science.gov (United States)

    Abanov, Artem; Tretiakov, Oleg; Liu, Yang

    2011-03-01

    We study current-induced domain-wall motion in a narrow ferromagnetic wire. We propose a way to move domain walls with a resonant time-dependent current which dramatically decreases the Ohmic losses in the wire and allows driving of the domain wall with higher speed without burning the wire. For any domain wall velocity we find the time-dependence of the current needed to minimize the Ohmic losses. Below a critical domain-wall velocity specified by the parameters of the wire the minimal Ohmic losses are achieved by dc current. Furthermore, we identify the wire parameters for which the losses reduction from its dc value is the most dramatic. This work was supported by the NSF Grant No. 0757992 and Welch Foundation (A-1678).

  8. Improvement of Metal-Graphene Ohmic Contact Resistance in Bilayer Epitaxial Graphene Devices

    International Nuclear Information System (INIS)

    He Ze-Zhao; Yang Ke-Wu; Yu Cui; Li Jia; Liu Qing-Bin; Lu Wei-Li; Feng Zhi-Hong; Cai Shu-Jun

    2015-01-01

    We report on an improved metal-graphene ohmic contact in bilayer epitaxial graphene on a SiC substrate with contact resistance below 0.1 ω·mm. Monolayer and bilayer epitaxial graphenes are prepared on a 4H-SiC substrate in this work. Their contact resistances are measured by a transfer length method. An improved photoresist-free device fabrication method is used and is compared with the conventional device fabrication method. Compared with the monolayer graphene, the contact resistance R c of bilayer graphene improves from an average of 0.24 ω·mm to 0.1 ω·mm. Ohmic contact formation mechanism analysis by Landauer's approach reveals that the obtained low ohmic contact resistance in bilayer epitaxial graphene is due to their high carrier density, high carrier transmission probability, and p-type doping introduced by contact metal Au. (paper)

  9. Universal strategy for Ohmic hole injection into organic semiconductors with high ionization energies.

    Science.gov (United States)

    Kotadiya, Naresh B; Lu, Hao; Mondal, Anirban; Ie, Yutaka; Andrienko, Denis; Blom, Paul W M; Wetzelaer, Gert-Jan A H

    2018-04-01

    Barrier-free (Ohmic) contacts are a key requirement for efficient organic optoelectronic devices, such as organic light-emitting diodes, solar cells, and field-effect transistors. Here, we propose a simple and robust way of forming an Ohmic hole contact on organic semiconductors with a high ionization energy (IE). The injected hole current from high-work-function metal-oxide electrodes is improved by more than an order of magnitude by using an interlayer for which the sole requirement is that it has a higher IE than the organic semiconductor. Insertion of the interlayer results in electrostatic decoupling of the electrode from the semiconductor and realignment of the Fermi level with the IE of the organic semiconductor. The Ohmic-contact formation is illustrated for a number of material combinations and solves the problem of hole injection into organic semiconductors with a high IE of up to 6 eV.

  10. Modelling of Ohmic discharges in ADITYA tokamak using the Tokamak Simulation Code

    International Nuclear Information System (INIS)

    Bandyopadhyay, I; Ahmed, S M; Atrey, P K; Bhatt, S B; Bhattacharya, R; Chaudhury, M B; Deshpande, S P; Gupta, C N; Jha, R; Joisa, Y Shankar; Kumar, Vinay; Manchanda, R; Raju, D; Rao, C V S; Vasu, P

    2004-01-01

    Several Ohmic discharges of the ADITYA tokamak are simulated using the Tokamak Simulation Code (TSC), similar to that done earlier for the TFTR tokamak. Unlike TFTR, the dominant radiation process in ADITYA is through impurity line radiation. TSC can follow the experimental plasma current and position to very good accuracy. The thermal transport model of TSC including impurity line radiation gives a good match of the simulated results with experimental data for the Ohmic flux consumption, electron temperature and Z eff . Even the simulated magnetic probe signals are in reasonably good agreement with the experimental values

  11. Modelling of Ohmic discharges in ADITYA tokamak using the Tokamak Simulation Code

    Energy Technology Data Exchange (ETDEWEB)

    Bandyopadhyay, I; Ahmed, S M; Atrey, P K; Bhatt, S B; Bhattacharya, R; Chaudhury, M B; Deshpande, S P; Gupta, C N; Jha, R; Joisa, Y Shankar; Kumar, Vinay; Manchanda, R; Raju, D; Rao, C V S; Vasu, P [Institute for Plasma Research, Bhat, Gandhinagar 382428 (India)

    2004-09-01

    Several Ohmic discharges of the ADITYA tokamak are simulated using the Tokamak Simulation Code (TSC), similar to that done earlier for the TFTR tokamak. Unlike TFTR, the dominant radiation process in ADITYA is through impurity line radiation. TSC can follow the experimental plasma current and position to very good accuracy. The thermal transport model of TSC including impurity line radiation gives a good match of the simulated results with experimental data for the Ohmic flux consumption, electron temperature and Z{sub eff}. Even the simulated magnetic probe signals are in reasonably good agreement with the experimental values.

  12. Confinement requirements for OHMIC-compressive ignition of a Spheromak plasma

    International Nuclear Information System (INIS)

    Olson, R.; Gilligan, J.; Miley, G.

    1980-01-01

    The Moving Plasmoid Reactor (MPR) is an attractive alternative magnetic fusion scheme in which Spheromak plasmoids are envisioned to be formed, compressed, burned, and expanded as the plasmoids translate through a series of linear reactor modules. Although auxiliary heating of the plasmoids may be possible, the MPR scenario would be especially interesting if ohmic decay and compression along were sufficient to heat the plasmoids to an ignition temperature. In the present work, we will study the transport conditions under which a Spheromak plasmoid could be expected to reach ignition via a combination of ohmic and compression heating

  13. Confinement requirements for ohmic-compressive ignition of a Spheromak plasma

    International Nuclear Information System (INIS)

    Olson, R.E.; Miley, G.H.

    1981-01-01

    The Moving Plasmoid Reactor (MPR) is an attractive alternative magnetic fusion scheme in which Spheromak plasmoids are envisioned to be formed, compressed, burned, and expanded as the plasmoids translate through a series of linear reactor modules. Although auxiliary heating of the plasmoids may be possible, the MPR scenario would be especially interesting if ohmic decay and compression alone is sufficient to heat the plasmoids to an ignition temperature. In the present work, we examine the transport conditions under which a Spheromak plasmoid can be expected to reach ignition via a combination of ohmic and compression heating

  14. Pasteurization of citrus juices with ohmic heating to preserve the carotenoid profile

    OpenAIRE

    Achir , Nawel; Dhuique-Mayer , Claudie; Hadjal , Thiziri; Madani , Khodir; Pain , Jean-Pierre; Dornier , Manuel

    2016-01-01

    International audience; This study was carried out to assess, for the first time, the effect of ohmic heating on the carotenoid profile of two citrus fruit juices: grapefruit and blood orange. Two heat treatments were designed to obtain pasteurization values of 50 and 150 min (Tref= 70°C and z-value=10°C) with ohmic heating as compared to conventional heating. The results showed that xanthophyll losses could reach 70% for epoxyxanthophylls (cis-violaxanthin and cis-antheraxanthin) and 40% for...

  15. Highly Divergent Mitochondrial ATP Synthase Complexes in Tetrahymena thermophila

    NARCIS (Netherlands)

    Nina, Praveen Balabaskaran; Dudkina, Natalya V.; Kane, Lesley A.; van Eyk, Jennifer E.; Boekema, Egbert J.; Mather, Michael W.; Vaidya, Akhil B.; Eisen, Jonathan A.

    The F-type ATP synthase complex is a rotary nano-motor driven by proton motive force to synthesize ATP. Its F(1) sector catalyzes ATP synthesis, whereas the F(o) sector conducts the protons and provides a stator for the rotary action of the complex. Components of both F(1) and F(o) sectors are

  16. Engineering design solutions of flux swing with structural requirements for ohmic heating solenoids

    International Nuclear Information System (INIS)

    Smith, R.A.

    1977-01-01

    Here a more detailed publication is summarized which presents analytical methods with solutions that describe the structural behavior of ohmic heating solenoids to achieve a better understanding of the relationships between the functional variables that can provide the basis for recommended design improvements. The solutions relate the requirements imposed by structural integrity to the need for producing sufficient flux swing to initiate a plasma current in the tokamak fusion machine. A method is provided to perform a detailed structural analysis of every conducting turn in the radial build of the solenoid, and computer programmed listings for the closed form solutions are made available as part of the reference document. Distinction is made in deriving separate models for the regions of the solenoid where turn-to-turn radial contact is maintained with radial compression or with a bond in the presence of radial tension, and also where there is turn-to-turn radial separation due to the absence or the loss of bonding in the presence of would be radial tension. The derivations follow the theory of elasticity for a body possessing cylindrical anisotropy where the material properties are different in the radial and tangential directions. The formulations are made practical by presenting the methods for reducing stress and for relocating the relative position for potential turn-to-turn radial delamination by permitting an arbitrary traction at the outer radial surface of the solenoid in the form of pressure or displacement such as may be applied by a containment or a shrink fit structural cylinder

  17. Transparent conductive oxides for thin-film silicon solar cells

    NARCIS (Netherlands)

    Löffler, J.

    2005-01-01

    This thesis describes research on thin-film silicon solar cells with focus on the transparent conductive oxide (TCO) for such devices. In addition to the formation of a transparent and electrically conductive front electrode for the solar cell allowing photocurrent collection with low ohmic losses,

  18. The isotope effect on divertor conditions and neutral pumping in horizontal divertor configurations in JET-ILW Ohmic plasmas

    Directory of Open Access Journals (Sweden)

    J. Uljanovs

    2017-08-01

    Full Text Available Understanding the impact of isotope mass and divertor configuration on the divertor conditions and neutral pressures is critical for predicting the performance of the ITER divertor in DT operation. To address this need, ohmically heated hydrogen and deuterium plasma experiments were conducted in JET with the ITER-like wall in varying divertor configurations. In this study, these plasmas are simulated with EDGE2D-EIRENE outfitted with a sub-divertor model, to predict the neutral pressures in the plenum with similar fashion to the experiments. EDGE2D-EIRENE predictions show that the increased isotope mass results in up to a 25% increase in peak electron densities and 15% increase in peak ion saturation current at the outer target in deuterium when compared to hydrogen for all horizontal divertor configurations. Indicating that a change from hydrogen to deuterium as main fuel decreases the neutral mean free path, leading to higher neutral density in the divertor. Consequently, this mechanism also leads to higher neutral pressures in the sub-divertor. The experimental data provided by the hydrogen and deuterium ohmic discharges shows that closer proximity of the outer strike point to the pumping plenum results in a higher neutral pressure in the sub-divertor. The diaphragm capacitance gauge pressure measurements show that a two to three-fold increase in sub-divertor pressure was achieved in the corner and nearby horizontal configurations compared to the far-horizontal configurations, likely due to ballistic transport (with respect to the plasma facing components of the neutrals into the sub-divertor. The corner divertor configuration also indicates that a neutral expansion occurs during detachment, resulting in a sub-divertor neutral density plateau as a function of upstream density at the outer-mid plane.

  19. Highly divergent mitochondrial ATP synthase complexes in Tetrahymena thermophila.

    Directory of Open Access Journals (Sweden)

    Praveen Balabaskaran Nina

    2010-07-01

    Full Text Available The F-type ATP synthase complex is a rotary nano-motor driven by proton motive force to synthesize ATP. Its F(1 sector catalyzes ATP synthesis, whereas the F(o sector conducts the protons and provides a stator for the rotary action of the complex. Components of both F(1 and F(o sectors are highly conserved across prokaryotes and eukaryotes. Therefore, it was a surprise that genes encoding the a and b subunits as well as other components of the F(o sector were undetectable in the sequenced genomes of a variety of apicomplexan parasites. While the parasitic existence of these organisms could explain the apparent incomplete nature of ATP synthase in Apicomplexa, genes for these essential components were absent even in Tetrahymena thermophila, a free-living ciliate belonging to a sister clade of Apicomplexa, which demonstrates robust oxidative phosphorylation. This observation raises the possibility that the entire clade of Alveolata may have invented novel means to operate ATP synthase complexes. To assess this remarkable possibility, we have carried out an investigation of the ATP synthase from T. thermophila. Blue native polyacrylamide gel electrophoresis (BN-PAGE revealed the ATP synthase to be present as a large complex. Structural study based on single particle electron microscopy analysis suggested the complex to be a dimer with several unique structures including an unusually large domain on the intermembrane side of the ATP synthase and novel domains flanking the c subunit rings. The two monomers were in a parallel configuration rather than the angled configuration previously observed in other organisms. Proteomic analyses of well-resolved ATP synthase complexes from 2-D BN/BN-PAGE identified orthologs of seven canonical ATP synthase subunits, and at least 13 novel proteins that constitute subunits apparently limited to the ciliate lineage. A mitochondrially encoded protein, Ymf66, with predicted eight transmembrane domains could be a

  20. Reducing the acidity of Arabica coffee beans by ohmic fermentation technology

    Directory of Open Access Journals (Sweden)

    Reta

    2017-07-01

    Full Text Available Coffee is widely consumed not only because of its typical taste, but coffee has antioxidant properties because of its polygons, and it stimulates brain performance. The main problem with the consumption of coffee is its content of caffeine. Caffeine when consumed in excess, can increase muscle tension, stimulate the heart, and increase the secretion of gastric acid. In this research, we applied ohmic fermentation technology, which is specially designed to mimic the stomach. Arabica coffee has high acidity that needs to be reduced than Luwak coffee, although it is cheaper. Hence, the ohmic technology with a time and temperature variation were applied to measure the total acidity of the coffee to determine optimum fermentation conditions. Results revealed that the total acidity of the coffee varied with fermentation conditions (0.18% – 0.73%. Generally, the longer the fermentation and the higher the temperature, the lower the total acidity. The acidity of the Luwak coffee through natural fermentation was 2.34%, which is substantially higher than the total acidity from the ohmic samples. Ohmic-based fermentation technology, therefore, offers improvements in coffee quality.

  1. Characterization of recessed Ohmic contacts to AlGaN/GaN

    NARCIS (Netherlands)

    Hajlasz, M.; Donkers, J.J.T.M.; Sque, S.J.; Heil, S.B.S.; Gravesteijn, Dirk J; Rietveld, F.J.R.; Schmitz, Jurriaan

    2015-01-01

    In this work the choice of appropriate test structures and characterization methods for recessed Ohmic contacts to AlGaN/GaN is discussed. It is shown that, in the worst-case scenario, the prevailing assumption of identical sheet resistance between and under the contacts can lead to errors of up to

  2. Effect of ohmic heating of soymilk on urease inactivation and kinetic analysis in holding time.

    Science.gov (United States)

    Li, Fa-De; Chen, Chen; Ren, Jie; Wang, Ranran; Wu, Peng

    2015-02-01

    To verify the effect of the ohmic heating on the urease activity in the soymilk, the ohmic heating methods with the different electrical field conditions (the frequency and the voltage ranging from 50 to 10 kHz and from 160 to 220 V, respectively) were employed. The results showed that if the value of the urease activity measured with the quantitative spectrophotometry method was lower than 16.8 IU, the urease activity measured with the qualitative method was negative. The urease activity of the sample ohmically heated was significantly lower than that of the sample conventionally heated (P urease inactivation. In addition, the inactivation kinetics of the urease in the soymilk could be described with a biphasic model during holding time at a target temperature. Thus, it was concluded that the urease in the soymilk would contain 2 isoenzymes, one is the thermolabile fraction, the other the thermostable fraction, and that the thermostable isoenzyme could not be completely inactivated when the holding time increased, whether the soymilk was cooked with the conventional method or with the ohmic heating method. Therefore, the electric field had no effect on the inactivation of the thermostable isoenzyme of the urease. © 2015 Institute of Food Technologists®

  3. Internal transport barrier and β limit in ohmically heated plasma in TUMAN-3M

    International Nuclear Information System (INIS)

    Andreiko, M.V.; Askinazi, L.G.; Golant, V.E.

    2001-01-01

    An Internal Transport Barrier (ITB) was found in ohmically heated plasma in TUMAN-3M (R 0 =53 cm, a l =22 cm - circular limiter configuration, B t ≤0.7T, I p ≤175 kA, ≤6.0·10 19 m -3 ). The barrier reveals itself as a formation of a steep gradient on electron temperature and density radial profiles. The regions with reduced diffusion and electron thermal diffusivity are in between r=0.5a and r=0.7a. The ITB appears more frequently in the shots with higher plasma current. At lower currents (I p N limit in the ohmically heated plasma are presented. Stored energy was measured using diamagnetic loops and compared with W calculated from kinetic data obtained by Thomson scattering and microwave interferometry. Measurements of the stored energy and of the β were performed in the ohmic H-mode before and after boronization and in the scenario with the fast Current Ramp-Down in the ohmic H-mode. Maximum value of β T of 2.0 % and β N of 2 were achieved. The β N limit achieved is 'soft' (nondisruptive) limit. The stored energy slowly decays after the Current Ramp-Down. No correlation was found between beta restriction and MHD phenomena. (author)

  4. Internal transport barrier and β limit in ohmically heated plasma in TUMAN-3M

    International Nuclear Information System (INIS)

    Andreiko, M.V.; Askinazi, L.G.; Golant, V.E.

    1999-01-01

    An Internal Transport Barrier (ITB) was found in ohmically heated plasma in TUMAN-3M (R 0 = 53 cm, a l = 22 cm - circular limiter configuration, B t ≤ 0.7 T, I p ≤ 175 kA, ≤ 6.0·10 19 m -3 ). The barrier reveals itself as a formation of a steep gradient on electron temperature and density radial profiles. The regions with reduced diffusion and electron thermal diffusivity are in between r = 0.5a and r = 0.7a. The ITB appears more frequently in the shots with higher plasma current. At lower currents (I p N limit in the ohmically heated plasma are presented. Stored energy was measured using diamagnetic loops and compared with W calculated from kinetic data obtained by Thomson scattering and microwave interferometry. Measurements of the stored energy and of the β were performed in the ohmic H-mode before and after boronization and in the scenario with the fast Current Ramp-Down in the ohmic H-mode. Maximum value of β T of 2.0% and β N of 2 were achieved. The β N limit achieved is 'soft' (non-disruptive) limit. The stored energy slowly decays after the Current Ramp-Down. No correlation was found between beta restriction and MHD phenomena. (author)

  5. Impurity toroidal rotation and transport in Alcator C-Mod ohmic high confinement mode plasmas

    International Nuclear Information System (INIS)

    Rice, J. E.; Goetz, J. A.; Granetz, R. S.; Greenwald, M. J.; Hubbard, A. E.; Hutchinson, I. H.; Marmar, E. S.; Mossessian, D.; Pedersen, T. Sunn; Snipes, J. A.

    2000-01-01

    Central toroidal rotation and impurity transport coefficients have been determined in Alcator C-Mod [I. H. Hutchinson et al., Phys. Plasmas 1, 1511 (1994)] Ohmic high confinement mode (H-mode) plasmas from observations of x-ray emission following impurity injection. Rotation velocities up to 3x10 4 m/sec in the co-current direction have been observed in the center of the best Ohmic H-mode plasmas. Purely ohmic H-mode plasmas display many characteristics similar to ion cyclotron range of frequencies (ICRF) heated H-mode plasmas, including the scaling of the rotation velocity with plasma parameters and the formation of edge pedestals in the electron density and temperature profiles. Very long impurity confinement times (∼1 sec) are seen in edge localized mode-free (ELM-free) Ohmic H-modes and the inward impurity convection velocity profile has been determined to be close to the calculated neoclassical profile. (c) 2000 American Institute of Physics

  6. A new method for the compensation of ohmic drop in galvanic cells

    NARCIS (Netherlands)

    Kooijman, D.J.; Sluyters, J.H.

    Generally the ohmic potential drop in a galvanic cell that occurs if a rectangular pulse is led through the cell, is compensated by means of a well-known bridge circuit. A better method making use of a phase reverter is described and its features are discussed. Exchange current densities up to 1200

  7. Low ohmic multilayer contacts in lead-tin-telluride diode lasers

    International Nuclear Information System (INIS)

    Herrmann, K.; Sumpf, B.; Boehme, D.; Hannemann, M.

    1983-01-01

    The preparation and the influence of low ohmic multilayer thin film contacts of lead-salt homo- and heterolasers on the degradation of lasing parameters during recycling processes between low working temperatures and room temperatures storage are described and discussed in detail. (author)

  8. Schottky and Ohmic Au contacts on GaAs: Microscopic and electrical investigation

    International Nuclear Information System (INIS)

    Liliental-Weber, Z.; Gronsky, R.; Washburn, J.; Newman, N.; Spicer, W.E.; Weber, E.R.

    1986-01-01

    We report here a systematic study which uses electrical device measurements and transmission electron microscopy (TEM) methods to investigate the electrical, morphological, and structural properties of Au/GaAs Schottky diodes. The electrical characteristics of Au diodes formed on atomically clean and air-exposed GaAs(110) surfaces are found to change from rectifying to Ohmic behavior after annealing above the Au--Ga eutectic temperature (360 0 C). This change is shown to be due to an Ohmic-like contact at the periphery of the device. TEM studies of these structures indicate that the Ohmic peripheral current pathway can be correlated with the formation of near surface Ga-rich Au crystallites at the diode circumference upon annealing. Further evidence of the correlation of the Ohmic electrical characteristics with the morphology of the periphery comes from data which indicate that the removal of these Au crystallites by mesa etching is also accompanied with the elimination of the Ohmic current. The morphology of the overlayer was found to depend strongly on annealing and surface treatment. TEM indicates that the interface is flat and abrupt for all unannealed diodes, as well as for annealed diodes formed on atomically clean surfaces. For annealed diodes formed on the air-exposed surfaces, the metal--semiconductor interface contains large metallic protrusions extending up to several hundred angstroms into the semiconductor. For comparison to practical structures, the morphology of annealed diodes formed using typical commercial processing technology [i.e., formed on chemically prepared (100) surfaces annealed in forming gas] was also investigated using TEM. The interface for these structures is more complex than interfaces formed on the atomically clean and air-exposed cleaved (110) surfaces

  9. Scaling of energy confinement with minor radius, current and density in Doublet III Ohmically heated plasmas

    International Nuclear Information System (INIS)

    Ejima, S.; Petrie, T.W.; Riviere, A.C.

    1982-01-01

    The dependence of plasma energy confinement on minor radius, density and plasma current is described for Ohmically heated near-circular plasmas in Doublet III. A wide range of parameters is used for the study of scaling laws; the plasma minor radius defined by the flux surface in contact with limiter is varied by a factor of 2 (a = 44, 32, and 23 cm), the line average plasma density, nsub(e)-bar, is varied by a factor of 20 from 0.5 to 10 x 10 13 cm -3 (nsub(e)-bar R 0 /Bsub(T) = 0.3 to 6 x 10 14 cm -2 .kG -1 ) and the plasma current, I, is varied by a factor of 6 from 120 to 718 kA. The range of the limiter safety factor, qsub(L), is from 2 to 12. - For plasmas with a = 23 and 32 cm, the scaling law at low nsub(e)-bar for the gross electron energy confinement time can be written as (s, cm) tausub(Ee)sup(G) approx.= 3.6 x 10 -19 nsub(e)-bar a 2 qsub(c)sup(3/4), where qsub(c) = 2πa 2 Bsub(T)/μ 0 IR 0 . For the 44-cm plasmas, tausub(Ee)sup(G) is about 1.8 times less than predicted by this scaling, possibly owing to the change in limiter configuration and small plasma-wall separation and/or the aspect ratio change. At high nsub(e)-bar, tausub(Ee)sup(G) saturates and in many cases decreases with nsub(e)-bar but increases with I in a classical-like manner. The dependence of tausub(Ee)sup(G) on a is considerably weakened. The confinement behaviour can be explained by taking an ion thermal conductivity 2 to 7 times that given by Hinton-Hazeltine's neoclassical theory with a lumped-Zsub(eff) impurity model. Within this range the enhancement factor increases with a or a/R 0 . The electron thermal conductivity evaluated at half-temperature radius where most of the thermal insulation occurs sharply increases with average current density within that radius, but does not depend on a within the uncertainties of the measurements. (author)

  10. Trap-assisted tunneling in aluminum-doped ZnO/indium oxynitride nanodot interlayer Ohmic contacts on p-GaN

    Energy Technology Data Exchange (ETDEWEB)

    Ke, Wen-Cheng, E-mail: wcke@mail.ntust.edu.tw; Yang, Cheng-Yi [Department of Materials Science and Engineering, National Taiwan University of Science and Technology, Taipei 106, Taiwan (China); Lee, Fang-Wei; Chen, Wei-Kuo [Department of Electrophysics, National Chiao-Tung University, Hsin-Chu 300, Taiwan (China); Huang, Hao-Ping [Department of Mechanical Engineering, Yuan Ze University, Chung-Li 320, Taiwan (China)

    2015-10-21

    This study developed an Ohmic contact formation method for a ZnO:Al (AZO) transparent conductive layer on p-GaN films involving the introduction of an indium oxynitride (InON) nanodot interlayer. An antisurfactant pretreatment was used to grow InON nanodots on p-GaN films in a RF magnetron sputtering system. A low specific contact resistance of 1.12 × 10{sup −4} Ω cm{sup 2} was achieved for a sample annealed at 500 °C for 30 s in nitrogen ambient and embedded with an InON nanodot interlayer with a nanodot density of 6.5 × 10{sup 8} cm{sup −2}. By contrast, a sample annealed in oxygen ambient exhibited non-Ohmic behavior. X-ray photoemission spectroscopy results showed that the oxygen vacancy (V{sub o}) in the InON nanodots played a crucial role in carrier transport. The fitting I–V characteristic curves indicated that the hopping mechanism with an activation energy of 31.6 meV and trap site spacing of 1.1 nm dominated the carrier transport in the AZO/InON nanodot/p-GaN sample. Because of the high density of donor-like oxygen vacancy defects at the InON nanodot/p-GaN interface, positive charges from the underlying p-GaN films were absorbed at the interface. This led to positive charge accumulation, creating a narrow depletion layer; therefore, carriers from the AZO layer passed through InON nanodots by hopping transport, and subsequently tunneling through the interface to enter the p-GaN films. Thus, AZO Ohmic contact can be formed on p-GaN films by embedding an InON nanodot interlayer to facilitate trap-assisted tunneling.

  11. Effect of frequency and waveform on inactivation of Escherichia coli O157:H7 and Salmonella enterica Serovar Typhimurium in salsa by ohmic heating.

    Science.gov (United States)

    Lee, Su-Yeon; Ryu, Sangryeol; Kang, Dong-Hyun

    2013-01-01

    The effect of frequency of alternating current during ohmic heating on electrode corrosion, heating rate, inactivation of food-borne pathogens, and quality of salsa was investigated. The impact of waveform on heating rate was also investigated. Salsa was treated with various frequencies (60 Hz to 20 kHz) and waveforms (sine, square, and sawtooth) at a constant electric field strength of 12.5 V/cm. Electrode corrosion did not occur when the frequency exceeded 1 kHz. The heating rate of the sample was dependent on frequency up to 500 Hz, but there was no significant difference (P > 0.05) in the heating rate when the frequency was increased above 1 kHz. The electrical conductivity of the sample increased with a rise in the frequency. At a frequency of 60 Hz, the square wave produced a lower heating rate than that of sine and sawtooth waves. The heating rate between waveforms was not significantly (P > 0.05) different when the frequency was >500 Hz. As the frequency increased, the treatment time required to reduce Escherichia coli O157:H7 and Salmonella enterica serovar Typhimurium to below the detection limit (1 log CFU/g) decreased without affecting product quality. These results suggest that ohmic heating can be effectively used to pasteurize salsa and that the effect of inactivation is dependent on frequency and electrical conductivity rather than waveform.

  12. Electric conductivity and bootstrap current in tokamak

    International Nuclear Information System (INIS)

    Mao Jianshan; Wang Maoquan

    1996-12-01

    A modified Ohm's law for the electric conductivity calculation is presented, where the modified ohmic current can be compensated by the bootstrap current. A comparison of TEXT tokamak experiment with the theories shows that the modified Ohm's law is a more close approximation to the tokamak experiments than the classical and neoclassical theories and can not lead to the absurd result of Z eff <1, and the extended neoclassical theory would be not necessary. (3 figs.)

  13. Structural Basis of Catalysis in the Bacterial Monoterpene Synthases Linalool Synthase and 1,8-Cineole Synthase

    OpenAIRE

    Karuppiah, Vijaykumar; Ranaghan, Kara E.; Leferink, Nicole G. H.; Johannissen, Linus O.; Shanmugam, Muralidharan; Ní Cheallaigh, Aisling; Bennett, Nathan J.; Kearsey, Lewis J.; Takano, Eriko; Gardiner, John M.; van der Kamp, Marc W.; Hay, Sam; Mulholland, Adrian J.; Leys, David; Scrutton, Nigel S.

    2017-01-01

    Terpenoids form the largest and stereochemically most diverse class of natural products, and there is considerable interest in producing these by biocatalysis with whole cells or purified enzymes, and by metabolic engineering. The monoterpenes are an important class of terpenes and are industrially important as flavors and fragrances. We report here structures for the recently discovered Streptomyces clavuligerus monoterpene synthases linalool synthase (bLinS) and 1,8-cineole synthase (bCinS)...

  14. Low resistance and transparent Ag/AZO ohmic contact to p-GaN

    International Nuclear Information System (INIS)

    Han, T.; Wang, T.; Gan, X. W.; Wu, H.; Shi, Y.; Liu, C.

    2014-01-01

    Silver (Ag)/ aluminum-doped zinc oxide (AZO) films were deposited on p-GaN by using electron beam evaporation. After the annealing process, current -voltage (I-V) measurements were carried out to determine the characteristic of the contacts. The Ag/AZO films annealed at 600 .deg. C were found to present an ohmic contact behavior. The specific contact resistance was calculated to be 9.76 x 10 -4 Ωcm 2 and the transmittance was over 80% for visibly light. The atomic force microscope was used to measure the aggregation of Ag grains which may have been the main factor in the formation of the Ag/AZO ohmic contact to p-GaN.

  15. Methylation effect on the ohmic resistance of a poly-GC DNA-like chain

    Energy Technology Data Exchange (ETDEWEB)

    Moura, F.A.B.F. de, E-mail: fidelis@fis.ufal.br [Instituto de Física, Universidade Federal de Alagoas, Maceió AL 57072-970 (Brazil); Lyra, M.L. [Instituto de Física, Universidade Federal de Alagoas, Maceió AL 57072-970 (Brazil); Almeida, M.L. de; Ourique, G.S.; Fulco, U.L.; Albuquerque, E.L. [Departamento de Biofísica e Farmacologia, Universidade Federal do Rio Grande do Norte, 59072-970, Natal-RN (Brazil)

    2016-10-14

    We determine, by using a tight-binding model Hamiltonian, the characteristic current–voltage (IxV) curves of a 5-methylated cytosine single strand poly-GC DNA-like finite segment, considering the methyl groups attached laterally to a random fraction of the cytosine basis. Striking, we found that the methylation significantly impacts the ohmic resistance (R) of the DNA-like segments, indicating that measurements of R can be used as a biosensor tool to probe the presence of anomalous methylation. - Highlights: • Ohmic resistance of finite segments of poly-CG DNA-like segments. • Possibility for the development of biosensor devices. • Methylation effect and electronic transport in DNA-like segments.

  16. Dynamics of the sub-Ohmic spin-boson model: A time-dependent variational study

    International Nuclear Information System (INIS)

    Wu Ning; Duan Liwei; Zhao Yang; Li Xin

    2013-01-01

    The Dirac-Frenkel time-dependent variation is employed to probe the dynamics of the zero temperature sub-Ohmic spin-boson model with strong friction utilizing the Davydov D 1 ansatz. It is shown that initial conditions of the phonon bath have considerable influence on the dynamics. Counterintuitively, even in the very strong coupling regime, quantum coherence features still manage to survive under the polarized bath initial condition, while such features are absent under the factorized bath initial condition. In addition, a coherent-incoherent transition is found at a critical coupling strength α≈ 0.1 for s= 0.25 under the factorized bath initial condition. We quantify how faithfully our ansatz follows the Schrödinger equation, finding that the time-dependent variational approach is robust for strong dissipation and deep sub-Ohmic baths (s≪ 1).

  17. Investigation of the Energy Confinement in Ohmic and LHCD Plasmas in HT-7

    International Nuclear Information System (INIS)

    Zhang Xiaoqing; Wan Baonian; Shen Biao; Hu Xiwei; Qian Jinping; Fan Hengyu; Ding Yonghua

    2006-01-01

    Investigation of the energy confinement in ohmic and lower hybrid current drive (LHCD) plasmas in HT-7 has been performed. In ohmic discharges at low densities the global energy confinement time τ E increases almost linearly with the density, saturates at a critical density (2.5 x 10 13 /cm 3 for HT-7) and is nearly constant at higher densities. The energy confinement time is in good agreement with the Neo-Alcator scaling law at different densities and currents. In the LHCD plasmas the global energy confinement time similar to that of the L-mode discharges has been observed to be in good agreement with the low confinement mode (L mode) scaling law of ITER89-P in higher electron density and plasma current

  18. Real-time protection of the Ohmic heating coil force limits in DIII-D

    International Nuclear Information System (INIS)

    Broesch, J.D.; Scoville, J.T.; Hyatt, A.W.; Coon, R.M.

    1997-11-01

    The maximum safe operating limits of the DIII-D tokamak are determined by the force produced in the ohmic heating coil and the toroidal field coil during a plasma pulse. This force is directly proportional to the product of the current in the coils. Historically, the current limits for each coil were set statically before each pulse without regard for the time varying nature of the currents. In order to allow the full time-dependent capability of the ohmic coil to be used, a system was developed for monitoring the product of the currents dynamically and making appropriate adjustments in real time. This paper discusses the purpose, implementation, and results of this work

  19. Observations of core toroidal rotation reversals in Alcator C-Mod ohmic L-mode plasmas

    International Nuclear Information System (INIS)

    Rice, J.E.; Reinke, M.L.; Podpaly, Y.A.; Churchill, R.M.; Cziegler, I.; Dominguez, A.; Ennever, P.C.; Fiore, C.L.; Granetz, R.S.; Greenwald, M.J.; Hubbard, A.E.; Hughes, J.W.; Irby, J.H.; Ma, Y.; Marmar, E.S.; McDermott, R.M.; Porkolab, M.; Duval, B.P.; Bortolon, A.; Diamond, P.H.

    2011-01-01

    Direction reversals of intrinsic toroidal rotation have been observed in Alcator C-Mod ohmic L-mode plasmas following modest electron density or toroidal magnetic field ramps. The reversal process occurs in the plasma interior, inside of the q = 3/2 surface. For low density plasmas, the rotation is in the co-current direction, and can reverse to the counter-current direction following an increase in the electron density above a certain threshold. Reversals from the co- to counter-current direction are correlated with a sharp decrease in density fluctuations with k R ≥ 2 cm -1 and with frequencies above 70 kHz. The density at which the rotation reverses increases linearly with plasma current, and decreases with increasing magnetic field. There is a strong correlation between the reversal density and the density at which the global ohmic L-mode energy confinement changes from the linear to the saturated regime.

  20. Space charge limited conduction in CdSe thin films

    Indian Academy of Sciences (India)

    Unknown

    of trap limited space charge limited conduction (SCLC) at higher voltage. The transition voltage (Vt ) from ohmic to SCLC is found to be quite independent of ambient temperature as well as intensity of illumination. SCLC is explained on the basis of the exponential trap distribution in CdSe films. Trap depths estimated from.

  1. Ohmic heating of peaches in the wide range of frequencies (50 Hz to 1 MHz).

    Science.gov (United States)

    Shynkaryk, Mykola V; Ji, Taehyun; Alvarez, Valente B; Sastry, Sudhir K

    2010-09-01

    The ohmic heating (OH) rate of peaches was studied at fixed electric field strength of 60 V.cm⁻¹, square-shaped instant reversal bipolar pulses, and frequencies varying within 50 Hz to 1 MHz. Thermal damage of tissue was evaluated from electrical admittivity. It showed that the time for half disruption (τ(T)) of tissue was required more than 10 h at temperatures below 40 °C. However, cellular thermal disruption occurred almost instantly (τ(T) 90 °C). Electrical conductivity σ(o) and admittivity σ(o)* of tissue at T(o)= 0 °C and their temperature coefficients (m, m*) were calculated. For freeze-thawed tissues, σ and σ* as well as m and m* were nearly indifferent to the frequency. However, for the intact tissue, both σ(o), σ(o)* and m, m* were frequency dependent. For freeze-thawed product, the power factor (P) was approximately equal to 1 and indifferent to the frequency and temperature. On the other hand, strong frequency dependence was observed for intact tissue with the minimum P approximately equal to 0.68 in the range of tens of kHz. The time required to reach a target temperature t(f) was evaluated. The t(f) increased with frequency up to the middle of the range of tens of kHz and thereafter continuously decreased. Samples exposed to the low-frequency electric field demonstrated faster electro-thermal damage rates. The textural relaxation data supported more intense damage kinetics at low-frequency OH. It has been demonstrated that a combination of high-frequency OH with pasteurization at moderate temperature followed by rapid cooling minimizes texture degradation of peach tissue. In this study, we investigated the electric field frequency effect on the rate of OH of peaches. It was shown that the time required for reaching the target temperature is strongly dependent upon the frequency. Samples exposed to low-frequency OH demonstrated higher electro-thermal damage rates. It has been shown that the combination of high-frequency OH with

  2. Information of Zeff from the sawtooth-performances in the center of ohmic tokamak discharges

    International Nuclear Information System (INIS)

    Eberhagen, A.

    1987-09-01

    Achievement of information on the mean effective ion charge in the center of ohmic tokamak discharges from sawtooth-relaxations of the plasma is considered. This method is found to supply trustworthy results for usual tokamak parameters. While its application requires some effort in data analysis, it can provide a valuable determination of Z eff -data, independent of the information from bremsstrahlung radiation losses of the plasma. (orig.)

  3. Reducing the acidity of Arabica coffee beans by ohmic fermentation technology

    OpenAIRE

    Reta; Mursalim; Salengke; Junaedi, M.; Mariati; Sopade, P.

    2017-01-01

    Coffee is widely consumed not only because of its typical taste, but coffee has antioxidant properties because of its polygons, and it stimulates brain performance. The main problem with the consumption of coffee is its content of caffeine. Caffeine when consumed in excess, can increase muscle tension, stimulate the heart, and increase the secretion of gastric acid. In this research, we applied ohmic fermentation technology, which is specially designed to mimic the stomach. Arabica coffee has...

  4. Structural analysis of equilibrium and ohmic heating coil assemblies for the TFTR

    International Nuclear Information System (INIS)

    Chattopadhyay, S.

    1975-10-01

    The structural adequacy of the equilibrium and ohmic heating coils and their support systems for the TFTR device has been investigated. The capability of the coils to span ribs of the support structure has been established. The support structure has been found to be effective in resisting the magnetic forces in the coils. The bands encircling the outboard coils and the band tensioning devices have been found to perform adequately. The analysis is based on October 1975 conceptual design

  5. Ohmically heated toroidal experiment (OHTE) mobile ignition test reactor facility concept study

    International Nuclear Information System (INIS)

    Masson, L.S.; Watts, K.D.; Piscitella, R.R.; Sekot, J.P.; Drexler, R.L.

    1983-02-01

    This report presents the results of a study to evaluate the use of an existing nuclear test complex at the Idaho National Engineering Laboratory (INEL) for the assembly, testing, and remote maintenance of the ohmically heated toroidal experiment (OHTE) compact reactor. The portable reactor concept is described and its application to OHTE testing and maintenance requirements is developed. Pertinent INEL facilities are described and several test system configurations that apply to these facilities are developed and evaluated

  6. A new method of making ohmic contacts to p-GaN

    Energy Technology Data Exchange (ETDEWEB)

    Hernández-Gutierrez, C.A., E-mail: chernandez@fis.cinvestav.mx [DNyN, Cinvestav-IPN, México, DF, 07360 (Mexico); Kudriavtsev, Yu. [Departamento Ingeniería Eléctrica – SEES, Cinvestav-IPN, México, DF, 07360 (Mexico); Mota, Esteban [ESIME, Instituto Politécnico Nacional, México, DF, 07738 (Mexico); Hernández, A.G.; Escobosa-Echavarría, A.; Sánchez-Resendiz, V. [Departamento Ingeniería Eléctrica – SEES, Cinvestav-IPN, México, DF, 07360 (Mexico); Casallas-Moreno, Y.L.; López-López, M. [Departamento Física, Cinvestav-IPN, México, DF, 07360 (Mexico)

    2016-12-01

    Highlights: • Low resistance Ohmic contacts preparation is based on low energy high dose In{sup +} ion implantation into Metal/p-GaN to achieve a thin layer of In{sub x}Ga{sub 1-x}N just at the interface. • The specific ohmic contact was reduced from 10{sup −2} Ωcm{sup 2} to 2.5 × 10{sup −4} Ωcm{sup 2}. - Abstract: The structural, chemical, and electrical characteristics of In{sup +} ion-implanted Au/Ni, Au/Nb and Au/W ohmic contacts to p-GaN were investigated. After the preparation of Ni, Nb and W electrode on the surface of p-GaN, the metal/p-GaN contact interface was implanted by 30 keV In{sup +} ions with an implantation dose of 5 × 10{sup 15} ions/cm{sup 2} at room temperature to form a thin layer of In{sub x}Ga{sub 1-x}N located at the metal-semiconductor interface, achieved to reduce the specific contact resistance due to the improving quantum tunneling transport trough to the structure. The characterization was carried out by high-resolution X-ray diffraction, scanning electron microscopy, Raman spectroscopy, and secondary ion mass spectrometry to investigate the formation of ternary alloy, re-crystallization by rapid thermal annealing process after In{sup +} implantation, and the redistribution of elements. The specific contact resistance was extracted by current-voltage (I-V) curves using transmission line method; the lowest specific contact resistance of 2.5 × 10{sup −4} Ωcm{sup 2} was achieved for Au/Ni/p-In{sub x}Ga{sub 1-x}N/p-GaN ohmic contacts.

  7. Laser-annealed GaP OHMIC contacts for high-temperature devices

    International Nuclear Information System (INIS)

    Eknoyan, O.; Van der Hoeven, W.; Richardson, T.; Porter, W.A.; Coquat, J.A.

    1980-01-01

    The results of successful Nd:YAG laser annealed ohmic contacts on n-type GaP are reported. Comparisons on identical laser and thermal annealed contacts on the same substrates are performed. Aging investigations are also studied. The results indicate that laser annealed contacts have far superior electrical characteristics, much better surface morphology and are substantially more stable with aging than the same but thermally alloyed ones

  8. Ohmic ion temperature and thermal diffusivity profiles from the JET neutron emission profile monitor

    Energy Technology Data Exchange (ETDEWEB)

    Esposito, B. (ENEA, Frascati (Italy). Centro Ricerche Energia); Marcus, F.B.; Conroy, S.; Jarvis, O.N.; Loughlin, M.J.; Sadler, G.; Belle, P. van (Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking); Adams, J.M.; Watkins, N. (AEA Industrial Technology, Harwell (United Kingdom))

    1993-10-01

    The JET neutron emission profile monitor was used to study ohmically heated deuterium discharges. The radial profile of the neutron emissivity is deduced from the line-integral data. The profiles of ion temperature, T[sub i], and ion thermal diffusivity, [chi][sub i], are derived under steady-state conditions. The ion thermal diffusivity is higher than, and its scaling with plasma current opposite to, that predicted by neoclassical theory. (author).

  9. Ohmic ion temperature and thermal diffusivity profiles from the JET neutron emission profile monitor

    International Nuclear Information System (INIS)

    Esposito, B.

    1993-01-01

    The JET neutron emission profile monitor was used to study ohmically heated deuterium discharges. The radial profile of the neutron emissivity is deduced from the line-integral data. The profiles of ion temperature, T i , and ion thermal diffusivity, χ i , are derived under steady-state conditions. The ion thermal diffusivity is higher than, and its scaling with plasma current opposite to, that predicted by neoclassical theory. (author)

  10. Influence factors and temperature reliability of ohmic contact on AlGaN/GaN HEMTs

    Directory of Open Access Journals (Sweden)

    Liang Song

    2018-03-01

    Full Text Available In this paper, we have studied the performance of Ti/Al/Ni/Au ohmic contact with different Al and Au thicknesses and pretreatments. The temperature dependence of contact resistances (Rc was investigated and it shows that there are different optimal annealing temperatures with different metal thicknesses and pretreatments. The optimal annealing temperature is affected by Al and Au thickness and AlGaN thickness. The etched AlGaN barrier is useful to achieve good ohmic contact (0.24 Ω·mm with a low annealing temperature. Only the contact resistances of the samples with 130 nm Al layer kept stable and the contact resistances of the samples with 100nm and 160 nm Al layers increased with the measurement temperatures. The contact resistances showed a similar increase and then keep stable trend for all the samples in the long-term 400 °C aging process. The ohmic metal of 20/130/50/50 nm Ti/Al/Ni/Au with ICP etching is the superior candidate considering the contact resistance and reliability.

  11. Space chamber experiments of ohmic heating by high power microwave from the solar power satellite

    Energy Technology Data Exchange (ETDEWEB)

    Kaya, N.; Matsumoto, H.

    1981-12-01

    It is quantitatively predicted that a high power microwave from the Solar Power Satellite (SPS) nonlinearly interacts with the ionospheric plasma. The possible nonlinear interactions are ohmic heating, self-focusing and parametric instabilities. A rocket experiment called MINIX (Microwave-Ionosphere Nonlinear Interaction Experiment) has been attempted to examine these effects, but is note reported here. In parallel to the rocket experiment, a laboratory experiment in a space plasma simulation chamber has been carried out in order to examine ohmic heating in detail and to develop a system of the rocket experiment. Interesting results were observed and these results were utilized to revise the system of the rocket experiments. A significant microwave heating of plasma up to 150% temperature increase was observed with little electron density decrease. It was shown that the temperature increase is not due to the RF breakdown but to the ohmic heating in the simulated ionospheric plasma. These microwave effects have to be taken into account in the SPS Project in the future.

  12. AlGaN channel field effect transistors with graded heterostructure ohmic contacts

    Science.gov (United States)

    Bajaj, Sanyam; Akyol, Fatih; Krishnamoorthy, Sriram; Zhang, Yuewei; Rajan, Siddharth

    2016-09-01

    We report on ultra-wide bandgap (UWBG) Al0.75Ga0.25N channel metal-insulator-semiconductor field-effect transistors (MISFETs) with heterostructure engineered low-resistance ohmic contacts. The low intrinsic electron affinity of AlN (0.6 eV) leads to large Schottky barriers at the metal-AlGaN interface, resulting in highly resistive ohmic contacts. In this work, we use a reverse compositional graded n++ AlGaN contact layer to achieve upward electron affinity grading, leading to a low specific contact resistance (ρsp) of 1.9 × 10-6 Ω cm2 to n-Al0.75Ga0.25N channels (bandgap ˜5.3 eV) with non-alloyed contacts. We also demonstrate UWBG Al0.75Ga0.25N channel MISFET device operation employing the compositional graded n++ ohmic contact layer and 20 nm atomic layer deposited Al2O3 as the gate-dielectric.

  13. 1.0 MeV irradiation of OHMIC, MS, MIS contacts to InP

    International Nuclear Information System (INIS)

    Warren, C.E.; Wagner, B.F.; Anderson, W.A.

    1986-01-01

    The radiation effects of 1.0 MeV electrons with a dose of 10/sup 15/cm/sup -2/ to MS and MIS Schottky diodes on InP have been compared to the radiation effects of MIS diodes on GaAs and Si. The radiation effects to ohmic contacts were also investigated. The metal for the diodes on the InP was gold. Au/Ti/Al was used for the GaAs diodes and Cr for the silicon diodes. Oxide layers on InP were grown by anodization in 0.1 N KOH. Oxides to GaAs and Si were grown thermally. Ohmic contacts to InP were formed using AuGe/Ni and AuSn alloys, followed by annealing in N/sub 2//H/sub 2/ (85%/15%). Metal Semiconductor diodes on InP were found to be at least sensitive to the irradiation. The InP MS and MIS diodes showed only small changes in the current voltage (I-V) characteristic, whereas the GaAs and Si devices showed a decrease in reverse current after irradiation. The ohmic contact resistance was increased by a factor of 2 to 5 after irradiation

  14. Transport analysis of ohmic, L-mode and improved confinement discharges in FTU

    Energy Technology Data Exchange (ETDEWEB)

    Esposito, B [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Marinucci, M [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Romanelli, M [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Bracco, G [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Castaldo, C [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Cocilovo, V [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Giovannozzi, E [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Leigheb, M [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Monari, G [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Nowak, S [IFP CNR, Via R. Cozzi, 53, 20125 Milano (Italy); Sozzi, C [IFP CNR, Via R. Cozzi, 53, 20125 Milano (Italy); Tudisco, O [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Cesario, R [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Frigione, D [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Gormezano, C [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Granucci, G [IFP CNR, Via R. Cozzi, 53, 20125 Milano (Italy); Panaccione, L [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Pericoli-Ridolfini, V [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy); Pieroni, L [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati (Italy)

    2004-11-01

    A thorough investigation of confinement in Frascati Tokamak Upgrade has been carried out on a new database of ohmic, L-mode and advanced scenario discharges (multiple pellet-fuelled, radiation improved and internal transport barriers (ITBs)) obtained with the available auxiliary heating systems, namely electron cyclotron resonant heating, lower hybrid and ion Bernstein wave. A general agreement of the measured {tau}{sub E} with ITER97 L-mode scaling is found in ohmic and L-mode discharges. An improvement of the energy confinement time ({tau}{sub E}) of up to about 60% over the ITER97 L-mode scaling has been obtained in ITB discharges, together with a reduction in local electron transport in the region of high pressure gradient, and up to about 30% in pellet-fuelled discharges (where {tau}{sub E} as large as {approx}120 ms have been reached). The linear density dependence of {tau}{sub E} in ohmic discharges has been found to extend above the saturation density threshold in pellet-fuelled plasmas.

  15. Virtual Screening of Novel Glucosamine-6-Phosphate Synthase Inhibitors.

    Science.gov (United States)

    Lather, Amit; Sharma, Sunil; Khatkar, Anurag

    2018-01-01

    Infections caused by microorganisms are the major cause of death today. The tremendous and improper use of antimicrobial agents leads to antimicrobial resistance. Various currently available antimicrobial drugs are inadequate to control the infections and lead to various adverse drug reactions. Efforts based on computer-aided drug design (CADD) can excavate a large number of databases to generate new, potent hits and minimize the requirement of time as well as money for the discovery of newer antimicrobials. Pharmaceutical sciences also have made development with advances in drug designing concepts. The current research article focuses on the study of various G-6-P synthase inhibitors from literature cited molecular database. Docking analysis was conducted and ADMET data of various molecules was evaluated by Schrodinger Glide and PreADMET software, respectively. Here, the results presented efficacy of various inhibitors towards enzyme G-6-P synthase. Docking scores, binding energy and ADMET data of various molecules showed good inhibitory potential toward G-6-P synthase as compared to standard antibiotics. This novel antimicrobial drug target G-6-P synthase has not so extensively been explored for its application in antimicrobial therapy, so the work done so far proved highly essential. This article has helped the drug researchers and scientists to intensively explore about this wonderful antimicrobial drug target. The Schrodinger, Inc. (New York, USA) software was utilized to carry out the computational calculations and docking studies. The hardware configuration was Intel® core (TM) i5-4210U CPU @ 2.40GHz, RAM memory 4.0 GB under 64-bit window operating system. The ADMET data was calculated by using the PreADMET tool (PreADMET ver. 2.0). All the computational work was completed in the Laboratory for Enzyme Inhibition Studies, Department of Pharmaceutical Sciences, M.D. University, Rohtak, INDIA. Molecular docking studies were carried out to identify the binding

  16. Producing biofuels using polyketide synthases

    Science.gov (United States)

    Katz, Leonard; Fortman, Jeffrey L; Keasling, Jay D

    2013-04-16

    The present invention provides for a non-naturally occurring polyketide synthase (PKS) capable of synthesizing a carboxylic acid or a lactone, and a composition such that a carboxylic acid or lactone is included. The carboxylic acid or lactone, or derivative thereof, is useful as a biofuel. The present invention also provides for a recombinant nucleic acid or vector that encodes such a PKS, and host cells which also have such a recombinant nucleic acid or vector. The present invention also provides for a method of producing such carboxylic acids or lactones using such a PKS.

  17. Confinement studies of ohmically heated plasmas in TFTR

    International Nuclear Information System (INIS)

    Efthimion, P.C.; Bretz, N.L.; Bell, M.G.

    1985-03-01

    Systematic scans of density in large deuterium plasmas (a = 0.83 m) at several values of plasma current and toroidal magnetic field strength indicate that the total energy confinement time, tau/sub E/, is proportional to the line-average density anti n/sub e/ and the limiter q. Confinement times of approx. 0.3 s have been observed for anti n/sub e/ = 2.8 x 10 19 m -3 . Plasma size scaling experiments with plasmas of minor radii a = 0.83, 0.69, 0.55, and 0.41 m at constant limiter q reveal a confinement dependence on minor radius. The major-radius dependence of tau/sub E/, based on a comparison between TFTR and PLT results, is consistent with R 2 scaling. From the power balance, the thermal diffusivity chi/sub e/ is found to be significantly less than the INTOR value. In the a = 0.41 m plasmas, saturation of confinement is due to neoclassical ion conduction (chi/sub i/ neoclassical >> chi/sub e/)

  18. Effect of continuous ohmic heating to inactivate Escherichia coli O157:H7, Salmonella Typhimurium and Listeria monocytogenes in orange juice and tomato juice.

    Science.gov (United States)

    Lee, S-Y; Sagong, H-G; Ryu, S; Kang, D-H

    2012-04-01

    The purpose of this study was to investigate the efficacy of continuous ohmic heating for reducing Escherichia coli O157:H7, Salmonella Typhimurium and Listeria monocytogenes in orange juice and tomato juice. Orange juice and tomato juice were treated with electric field strengths in the range of 25-40 V cm(-1) for different treatment times. The temperature of the samples increased with increasing treatment time and electric field strength. The rate of temperature change for tomato juice was higher than for orange juice at all voltage gradients applied. Higher electric field strength or longer treatment time resulted in a greater reduction of pathogens. Escherichia coli O157:H7 was reduced by more than 5 log after 60-, 90- and 180-s treatments in orange juice with 40, 35 and 30 V cm(-1) electric field strength, respectively. In tomato juice, treatment with 25 V cm(-1) for 30 s was sufficient to achieve a 5-log reduction in E. coli O157:H7. Similar results were observed in Salm. Typhimurium and L. monocytogenes. The concentration of vitamin C in continuous ohmic heated juice was significantly higher than in conventionally heated juice (P pasteurize fruit and vegetable juices in a short operating time and that the effect of inactivation depends on applied electric field strengths, treatment time and electric conductivity. © 2012 The Authors. Journal of Applied Microbiology © 2012 The Society for Applied Microbiology.

  19. Heterooligomeric phosphoribosyl diphosphate synthase of Saccharomyces cerevisiae

    DEFF Research Database (Denmark)

    Hove-Jensen, Bjarne

    2004-01-01

    The yeast Saccharomyces cerevisiae contains five phosphoribosyl diphosphate (PRPP) synthase-homologous genes (PRS1-5), which specify PRPP synthase subunits 1-5. Expression of the five S. cerevisiae PRS genes individually in an Escherichia coli PRPP-less strain (Deltaprs) showed that a single PRS...

  20. Summary of experimental core turbulence characteristics in ohmic and electron cyclotron resonance heated discharges in T-10 tokamak plasmas

    International Nuclear Information System (INIS)

    Vershkov, V.A.; Shelukhin, D.A.; Soldatov, S.V.; Urazbaev, A.O.; Grashin, S.A.; Eliseev, L.G.; Melnikov, A.V.

    2005-01-01

    This report summarizes the results of experimental turbulence investigations carried out at T-10 for more than 10 years. The turbulence characteristics were investigated using correlation reflectometry, multipin Langmuir probe (MLP) and heavy ion beam probe diagnostics. The reflectometry capabilities were analysed using 2D full-wave simulations and verified by direct comparison using a MLP. The ohmic and electron cyclotron resonance heated discharges show the distinct transition from the core turbulence, having complex spectral structure, to the unstructured one in the scrape-off layer. The core turbulence includes 'broad band, quasi-coherent' features, arising due to the excitation of rational surfaces with high poloidal m-numbers, with a low frequency near zero and specific oscillations at 15-30 kHz. All experimentally measured properties of low frequency and high frequency quasi-coherent oscillations are in good agreement with predictions of linear theory for the ion temperature gradient/dissipative trapped electron mode instabilities. Significant local changes in the turbulence characteristics were observed at the edge velocity shear layer and in the core near q = 1 radius after switching off the electron cyclotron resonance heating (ECRH). The local decrease in the electron heat conductivity and decrease in the turbulence level could be evidence of the formation of an electron internal transport barrier. The dynamic behaviour of the core turbulence was also investigated for the case of fast edge cooling and the beginning phase of ECRH

  1. Development of high temperature stable Ohmic and Schottky contacts on n-gallium nitride

    Science.gov (United States)

    Khanna, Rohit

    In this work the effort was made to towards develop and investigate high temperature stable Ohmic and Schottky contacts for n type GaN. Various borides and refractory materials were incorporated in metallization scheme to best attain the desired effect of minimal degradation of contacts when placed at high temperatures. This work focuses on achieving a contact scheme using different borides which include two Tungsten Borides (namely W2B, W2B 5), Titanium Boride (TiB2), Chromium Boride (CrB2) and Zirconium Boride (ZrB2). Further a high temperature metal namely Iridium (Ir) was evaluated as a potential contact to n-GaN, as part of continuing improved device technology development. The main goal of this project was to investigate the most promising boride-based contact metallurgies on GaN, and finally to fabricate a High Electron Mobility Transistor (HEMT) and compare its reliability to a HEMT using present technology contact. Ohmic contacts were fabricated on n GaN using borides in the metallization scheme of Ti/Al/boride/Ti/Au. The characterization of the contacts was done using current-voltage measurements, scanning electron microscopy (SEM) and Auger Electron Spectroscopy (AES) measurements. The contacts formed gave specific contact resistance of the order of 10-5 to 10-6 Ohm-cm2. A minimum contact resistance of 1.5x10-6 O.cm 2 was achieved for the TiB2 based scheme at an annealing temperature of 850-900°C, which was comparable to a regular ohmic contact of Ti/Al/Ni/Au on n GaN. When some of borides contacts were placed on a hot plate or in hot oven for temperature ranging from 200°C to 350°C, the regular metallization contacts degraded before than borides ones. Even with a certain amount of intermixing of the metallization scheme the boride contacts showed minimal roughening and smoother morphology, which, in terms of edge acuity, is crucial for very small gate devices. Schottky contacts were also fabricated and characterized using all the five boride

  2. Threonine phosphorylation of rat liver glycogen synthase

    International Nuclear Information System (INIS)

    Arino, J.; Arro, M.; Guinovart, J.J.

    1985-01-01

    32 P-labeled glycogen synthase specifically immunoprecipitated from 32 P-phosphate incubated rat hepatocytes contains, in addition to [ 32 P] phosphoserine, significant levels of [ 32 P] phosphothreonine. When the 32 P-immunoprecipitate was cleaved with CNBr, the [ 32 P] phosphothreonine was recovered in the large CNBr fragment (CB-2, Mapp 28 Kd). Homogeneous rat liver glycogen synthase was phosphorylated by all the protein kinases able to phosphorylate CB-2 in vitro. After analysis of the immunoprecipitated enzyme for phosphoaminoacids, it was observed that only casein kinase II was able to phosphorylate on threonine and 32 P-phosphate was only found in CB-2. These results demonstrate that rat liver glycogen synthase is phosphorylated at threonine site(s) contained in CB-2 and strongly indicate that casein kinase II may play a role in the ''in vivo'' phosphorylation of liver glycogen synthase. This is the first protein kinase reported to phosphorylate threonine residues in liver glycogen synthase

  3. Glycogen Synthase Kinase-3β

    DEFF Research Database (Denmark)

    Munkholm, Klaus; Lenskjold, Toke; Jacoby, Anne Sophie

    2016-01-01

    cells were quantitated using enzyme immunometric assays. The activity of GSK-3β (serine-9-phosphorylated GSK-3β/total GSK-3β) was lower at baseline compared with follow-up. No significant mean change over time was observed in levels of total GSK-3β and serine-9-phosphorylated GSK-3β. Exploratory......Evidence indicates a role for glycogen synthase kinase-3β (GSK-3β) in the pathophysiology of mood disorders and in cognitive disturbances; however, the natural variation in GSK-3β activity over time is unknown. We aimed to investigate GSK-3β activity over time and its possible correlation...... with emotional lability, subjective mood fluctuations and cognitive function in healthy individuals. Thirty-seven healthy subjects were evaluated with neuropsychological tests and blood samples at baseline and 12-week follow-up. Total GSK-3β and serine-9-phosphorylated GSK-3β in peripheral blood mononuclear...

  4. Crystal structure of riboflavin synthase

    Energy Technology Data Exchange (ETDEWEB)

    Liao, D.-I.; Wawrzak, Z.; Calabrese, J.C.; Viitanen, P.V.; Jordan, D.B. (DuPont); (NWU)

    2010-03-05

    Riboflavin synthase catalyzes the dismutation of two molecules of 6,7-dimethyl-8-(1'-D-ribityl)-lumazine to yield riboflavin and 4-ribitylamino-5-amino-2,6-dihydroxypyrimidine. The homotrimer of 23 kDa subunits has no cofactor requirements for catalysis. The enzyme is nonexistent in humans and is an attractive target for antimicrobial agents of organisms whose pathogenicity depends on their ability to biosynthesize riboflavin. The first three-dimensional structure of the enzyme was determined at 2.0 {angstrom} resolution using the multiwavelength anomalous diffraction (MAD) method on the Escherichia coli protein containing selenomethionine residues. The homotrimer consists of an asymmetric assembly of monomers, each of which comprises two similar {beta} barrels and a C-terminal {alpha} helix. The similar {beta} barrels within the monomer confirm a prediction of pseudo two-fold symmetry that is inferred from the sequence similarity between the two halves of the protein. The {beta} barrels closely resemble folds found in phthalate dioxygenase reductase and other flavoproteins. The three active sites of the trimer are proposed to lie between pairs of monomers in which residues conserved among species reside, including two Asp-His-Ser triads and dyads of Cys-Ser and His-Thr. The proposed active sites are located where FMN (an analog of riboflavin) is modeled from an overlay of the {beta} barrels of phthalate dioxygenase reductase and riboflavin synthase. In the trimer, one active site is formed, and the other two active sites are wide open and exposed to solvent. The nature of the trimer configuration suggests that only one active site can be formed and be catalytically competent at a time.

  5. MHD-activity in ohmic, diverted and limited H-mode plasmas in TCV

    International Nuclear Information System (INIS)

    Pochelon, A.; Anton, M.; Buehlmann, F.; Dutch, M.J.; Duval, B.P.; Hirt, A.; Hofmann, F.; Joye, B.; Lister, J.B.; Llobet, X.; Martin, Y.; Moret, J.M.; Nieswand, C.; Pietrzyk, A.Z.; Tonetti, G.; Weisen, H.

    1994-01-01

    During its first year of operation the TCV tokamak has produced a variety of plasma configurations with currents in the range 150 to 800 kA and elongations in the range of 1.0 to 2.05. Ohmic H-modes have been obtained in diverted discharges and discharges limited on the graphite tiles inner wall. After boronisation in May 1994 H-modes with line average densities up to 1.7x10 20 m -3 , corresponding to a Murakami parameter of 10, were obtained. (author) 5 figs., 2 refs

  6. Design of constant current charging power supply for J-TEXT ohmic field capacitor banks

    International Nuclear Information System (INIS)

    Lv Shudong; Zhang Ming; Rao Bo; Yu Kexun; Yang Cheng

    2014-01-01

    The charging characteristic of the capacitor charging power supply was analyzed with practical series resonant topology. The method that setting two current taps and regulating PWM switching frequency was putted forward with close loop controlling algorithm to charge the multi-group capacitor banks with constant current. A capacitor charging power supply with the max output current 6.5 A and the max output voltage 2000 V is designed. Experimental results show that, this power supply can charge the four capacitor banks to any four different voltages in 1 minute with charging accuracy less than 1%, and meet the requirements of J-TEXT ohmic field power system. (authors)

  7. Transient snakes in an ohmic plasma associated with a minor disruption in the HT-7 Tokamak

    Energy Technology Data Exchange (ETDEWEB)

    Mao, Songtao; Xu, Liqing; Hu, Liqun; Chen, Kaiyun [Chinese Academy of Sciences, Hefei (China)

    2014-05-15

    A transient burst (∼2 ms, an order of the fast-particle slowdown timescale) of a spontaneous snake is observed for the first time in a HT-7 heavy impurity ohmic plasma. The features of the low-Z impurity snake are presented. The flatten electron profile due to the heavy impurity reveals the formation of a large magnetic island. The foot of the impurity accumulation is consistent with the location of the transient snake. The strong frequency-chirping behaviors and the spatial structures of the snake are also presented.

  8. Density fluctuations in ohmic-, L-mode an H-mode discharges of ASDEX

    Energy Technology Data Exchange (ETDEWEB)

    Dodel, G; Holzhauer, E [Stuttgart Univ. (Germany). Inst. fuer Plasmaforschung; Niedermeyer, H; Endler, M; Gerhardt, J; Giannone, L.; Wagner, F; Zohm, H [Max-Planck-Institut fuer Plasmaphysik, Garching (Germany)

    1991-01-01

    The 119 [mu]m laser scattering device ASDEX was used to investigate the direction of propagation and temporal development of density fluctuations. In ohmic discharges the density fluctuations propagate predominantly in the electron-diamagnetic direction and change direction with NI co-injection. A strong drop in total scattered power together with a further increase in the frequency shift is observed after the build-up of the transport barrier. Similar observations have been reported on other tokamaks. Due to the finite spatial resolution of the scattering system the variation of the fluctuations with local parameters cannot be sufficiently resolved to confirm their nature. (author) 5 refs., 3 figs.

  9. Density fluctuations in ohmic-, L-mode an H-mode discharges of ASDEX

    International Nuclear Information System (INIS)

    Dodel, G.; Holzhauer, E.

    1991-01-01

    The 119 μm laser scattering device ASDEX was used to investigate the direction of propagation and temporal development of density fluctuations. In ohmic discharges the density fluctuations propagate predominantly in the electron-diamagnetic direction and change direction with NI co-injection. A strong drop in total scattered power together with a further increase in the frequency shift is observed after the build-up of the transport barrier. Similar observations have been reported on other tokamaks. Due to the finite spatial resolution of the scattering system the variation of the fluctuations with local parameters cannot be sufficiently resolved to confirm their nature. (author) 5 refs., 3 figs

  10. Direct high-temperature ohmic heating of metals as liquid pipes.

    Science.gov (United States)

    Grosse, A V; Cahill, J A; Liddell, W L; Murphy, W J; Stokes, C S

    1968-05-03

    When a sufficiently high electric current is passed through a liquid metal, the electromagnetic pressure pinches off the liquid metal and interrupts the flow of current. For the first time the pinch effect has been overcome by use of centrifugal acceleration. By rotation of a pipe of liquid metal, tin or bismuth or their alloys, at sufficiently high speed, it can be heated electrically without intermission of the electric current. One may now heat liquid metallic substances, by resistive (ohmic) heating, to 5000 degrees K and perhaps higher temperatures.

  11. Backscattering analysis of AuGe-Ni ohmic contacts of n-GaAs

    International Nuclear Information System (INIS)

    Nassibian, A.G.; Kalkur, T.S.; Sutherland, G.J.; Cohen, D.

    1985-01-01

    AuGe-Ni is widely used for the fabrication of ohmic contacts to n-GaAs. The alloying behaviour of evaporated AuGe-Ni alloyed by furnace and Scanning Electron Beam, is characterised by Rutherford backscattering with 2MeV 4 He ions. Since the formation of alloyed AuGe-Ni contacts involves redistribution and diffusion of Ga, As, Ni, Ge and Au, it is difficult to separate the corresponding yields due to gold, Ga As, Ni and Ge in the spectrum. The technique used in the investigation involves assumption of depth distribution of elements and computing the resultant spectrum

  12. AlGaN/GaN high electron mobility transistors with implanted ohmic contacts

    International Nuclear Information System (INIS)

    Wang, H.T.; Tan, L.S.; Chor, E.F.

    2007-01-01

    Selective area silicon implantation for source/drain regions was integrated into the fabrication of molecular beam epitaxy-grown AlGaN/GaN HEMTs. Dopant activation was achieved by rapid thermal annealing at 1100 deg. C in flowing N 2 ambient for 120 s with an AlN encapsulation. Linear transmission line measurements showed that the resistance of the overlay Ti/Al/Ni/Au ohmic contacts was reduced by 61% compared to the control sample. After the Schottky Ni/Au gate formation, the typical DC characteristics displayed a higher current drive, smaller knee voltage and better gate control properties for HEMTs with implanted source and drain regions

  13. Hydrogen and deuterium pellet injection into ohmically and additionally ECR-heated TFR plasmas

    International Nuclear Information System (INIS)

    Drawin, H.W.

    1987-01-01

    The ablation clouds of hydrogen and deuterium pellets injected into ohmically and electron cyclotron resonance heated (ECRH) plasmas of the Fontenay-aux-Roses tokamak TFR have been photographed, their emission has been measured photoelectrically. Without ECRH the pellets penetrate deeply into the plasma, the clouds are striated. Injection during ECRH leads to ablation in the outer plasma region. The position of the ECR layer has no influence on the penetration depth which is only a few centimeters. The ablation clouds show no particular structure when ECRH is applied

  14. Ohmic Treatment of Pear Purées (cv. ‘Conference’ in Terms of Some Quality Related Attributes

    Directory of Open Access Journals (Sweden)

    Oana Viorela NISTOR

    2015-06-01

    Full Text Available The effect of ohmic treatment on some quality related characteristics of pear purée (cv. ‘Conference’ such as color, reducing sugars, total phenols, rheological behavior and microbial counts, was analyzed. The inactivation kinetics of pectin methyl esterase (PME in pear crude extract and purée were studied by conventional thermal and ohmic treatments. Thermal inactivation of PME in crude extract was described by a first-order kinetic model. The activation energy values suggested the presence of two isoenzymes with different thermostability. The ohmic heating reduced PME activity by 96% at 25 V·cm-1. Minimal changes induced by ohmic heating on above quality related aspects were observed. Supporting this statement, there were no significant changes in the nutritional and sensorial attributes. It was reported an increase of 3% of reducing sugar content for the ohmic heated samples. The phenolic content of the treated samples registered a reduction of 59% in comparison with fresh pear purée. The pear purée presented a non-Newtonian pseudoplastic behaviour. The Ostwald de Waele model was fitted to rheograms and the consistency coefficient (m and flow behavior index (n were determined. Results obtained for the microbial charge were higher in the control samples. Thus, microbial counts showed complete inactivation of yeast and mold at voltage gradient higher than 17.5 V·cm-1.

  15. Corona-induced electrohydrodynamic instabilities in low conducting liquids

    Energy Technology Data Exchange (ETDEWEB)

    Vega, F.; Perez, A.T. [Depto. Electronica y Electromagnetismo, Facultad de Fisica, Universidad de Sevilla, Avda. Reina Mercedes, s/n. 41012, Sevilla (Spain)

    2003-06-01

    The rose-window electrohydrodynamic (EHD) instability has been observed when a perpendicular field with an additional unipolar ion injection is applied onto a low conducting liquid surface. This instability has a characteristic pattern with cells five to 10 times greater than those observed in volume instabilities caused by unipolar injection. We have used corona discharge from a metallic point to perform some measurements of the rose-window instability in low conducting liquids. The results are compared to the linear theoretical criterion for an ohmic liquid. They confirmed that the minimum voltage for this instability is much lower than that for the interfacial instability in high conducting liquids. This was predicted theoretically in the dependence of the critical voltage as a function of the non-dimensional conductivity. It is shown that in a non-ohmic liquid the rose window appears as a secondary instability after the volume instability. (orig.)

  16. The cellulose synthase companion proteins act non-redundantly with CELLULOSE SYNTHASE INTERACTING1/POM2 and CELLULOSE SYNTHASE 6

    OpenAIRE

    Endler, Anne; Schneider, Rene; Kesten, Christopher; Lampugnani, Edwin R.; Persson, Staffan

    2016-01-01

    Cellulose is a cell wall constituent that is essential for plant growth and development, and an important raw material for a range of industrial applications. Cellulose is synthesized at the plasma membrane by massive cellulose synthase (CesA) complexes that track along cortical microtubules in elongating cells of Arabidopsis through the activity of the protein CELLULOSE SYNTHASE INTERACTING1 (CSI1). In a recent study we identified another family of proteins that also are associated with the ...

  17. Modelling the metal–semiconductor band structure in implanted ohmic contacts to GaN and SiC

    International Nuclear Information System (INIS)

    Pérez-Tomás, A; Fontserè, A; Placidi, M; Jennings, M R; Gammon, P M

    2013-01-01

    Here we present a method to model the metal–semiconductor (M–S) band structure to an implanted ohmic contact to a wide band gap semiconductor (WBG) such as GaN and SiC. The performance and understanding of the M–S contact to a WBG semiconductor is of great importance as it influences the overall performance of a semiconductor device. In this work we explore in a numerical fashion the ohmic contact properties to a WBG semiconductor taking into account the partial ionization of impurities and analysing its dependence on the temperature, the barrier height, the impurity level band energy and carrier concentration. The effect of the M–S Schottky barrier lowering and the Schottky barrier inhomogeneities are discussed. The model is applied to a fabricated ohmic contact to GaN where the M–S band structure can be completely determined. (paper)

  18. INCORPORATING AMBIPOLAR AND OHMIC DIFFUSION IN THE AMR MHD CODE RAMSES

    International Nuclear Information System (INIS)

    Masson, J.; Mulet-Marquis, C.; Chabrier, G.; Teyssier, R.; Hennebelle, P.

    2012-01-01

    We have implemented non-ideal magnetohydrodynamics (MHD) effects in the adaptive mesh refinement code RAMSES, namely, ambipolar diffusion and Ohmic dissipation, as additional source terms in the ideal MHD equations. We describe in details how we have discretized these terms using the adaptive Cartesian mesh, and how the time step is diminished with respect to the ideal case, in order to perform a stable time integration. We have performed a large suite of test runs, featuring the Barenblatt diffusion test, the Ohmic diffusion test, the C-shock test, and the Alfvén wave test. For the latter, we have performed a careful truncation error analysis to estimate the magnitude of the numerical diffusion induced by our Godunov scheme, allowing us to estimate the spatial resolution that is required to address non-ideal MHD effects reliably. We show that our scheme is second-order accurate, and is therefore ideally suited to study non-ideal MHD effects in the context of star formation and molecular cloud dynamics.

  19. The particle fluxes in the edge plasma during discharges with improved ohmic confinement in ASDEX

    International Nuclear Information System (INIS)

    Verbeek, H.; Poschenrieder, W.; Fu, J.K.; Soeldner, F.X.

    1989-01-01

    In the recent experimental period of ASDEX a new regime of improved ohmic confinement (IOC) was discovered. So far the energy confinement time τ E increased linearly with increasing line averaged density n e up to n e = 3·10 13 cm -3 saturated, however, at higher densities. In the new IOC regime τ E increases further with increasing n e up to ∼5·10 13 cm -3 . The IOC regime is achieved for D 2 discharges only since the last modification of the ASDEX divertor which substantially increased the recycling from the divertor through the divertor slits. It also led to a reduction in gas consumption for a discharge by a factor of about 2. As it appears, the high fuelling rate required during a fast ramp-up of the plasma density leads to a transition into the Saturated Ohmic Confinememt (SOC) regime. Vice versa, the strong reduction in the external gas feed when the preprogrammed density plateau is reached seems to be essential for establishing the IOC. It is characterized by a pronounced peaking of the density profile. During the transition from the SOC to the IOC regime large variations in the signals of all edge and divertor related diagnostics are observed. In this paper we concentrate on the results of the Low Energy Neutral Particle Analyser (LENA), the sniffer probe, on the mass spectrometers measuring the divertor exhaust pressure. (author) 7 refs., 2 figs

  20. Ohmic heating coil power supply using thyristor circuit breaker in a thermonuclear fusion device

    International Nuclear Information System (INIS)

    Tani, Keiji; Shimada, Ryuichi; Tamura, Sanae; Yabuno, Kohei; Koseki, Shoichiro.

    1982-01-01

    In a large scale Tokamak thermonuclear fusion device such as the critical plasma testing facility (JT60) presently under construction, mechanical breakers such as vacuum and air breakers are mostly used for interrupting DC heavy current which is supplied to the ohmic heating coils of inductive energy accumulation method. The practical use of the DC breakers employing thyristors has just been started because the history of thyristor development is short and thristors are still expensive, in spite of the advantages. In this paper, the circuit is investigated in which the excellent high speed controllability of thyristors is fully utilized, while the economy is taken into accout, and the experiment carried out with a unit model is described. It was found that a thyristor switch, which was constructed by connecting the high speed thyristors of peak off-state voltage rating 2,000 V and mean current rating 500 A in direct parallel, was able to interrupt 12.7 kA current in the power supply circuit of ohmic heating coils developed this time. In addition, the switch configuration was able to be greatly simplified. When the multistage raising of plasma current is required, the raise can be performed with a single thyristor breaker because it can make high speed control. Therefore, the capacity of the breaker can be doubly and drastically reduced. Also, if current unbalance might occur between thyristor switch units, it gives no problem since the time of reverse voltage after current interruption dispersed smaller as current increased. (Wakatsuki, Y.)

  1. W and WSix Ohmic contacts on p- and n-type GaN

    International Nuclear Information System (INIS)

    Cao, X.A.; Ren, F.; Pearton, S.J.; Zeitouny, A.; Eizenberg, M.; Zolper, J.C.; Abernathy, C.R.; Han, J.; Shul, R.J.; Lothian, J.R.

    1999-01-01

    W and WSi Ohmic contacts on both p- and n-type GaN have been annealed at temperatures from 300 to 1000 degree C. There is minimal reaction (≤100 Angstrom broadening of the metal/GaN interface) even at 1000 degree C. Specific contact resistances in the 10 -5 Ω cm 2 range are obtained for WSi x on Si-implanted GaN with a peak doping concentration of ∼5x10 20 cm -3 , after annealing at 950 degree C. On p-GaN, leaky Schottky diode behavior is observed for W, WSi x and Ni/Au contacts at room temperature, but true Ohmic characteristics are obtained at 250 - 300 degree C, where the specific contact resistances are, typically, in the 10 -2 Ω cm 2 range. The best contacts for W and WSi x are obtained after 700 degree C annealing for periods of 30 - 120 s. The formation of β-W 2 N interfacial phases appear to be important in determining the contact quality. copyright 1999 American Vacuum Society

  2. Design of TFTR movable limiter blades for ohmic and neutral-beam-heated plasmas

    International Nuclear Information System (INIS)

    Doll, D.W.; Ulrickson, M.A.; Cecchi, J.L.; Citrolo, J.C.; Weissenburger, D.; Bialek, J.

    1981-10-01

    A new set of movable limiter blades has been designed for TFTR that will meet both the requirements of the 4 MW ohmic heated and the 33 MW neutral beam heated plasmas. This is accomplished with three limiter blades each having and elliptical shape along the toroidal direction. Heat flux levels are acceptable for both ohmic heated and pre-strong compression plasmas. The construction consists of graphite tiles attached to cooled backing plates. The tiles have an average thickness of approx. 4.7 cm and are drawn against the backing plate with spring loaded fasteners that are keyed into the graphite. The cooled backing plate provides the structure for resisting disruption and fault induced loads. A set of rollers attached to the top and bottom blades allow them to be expanded and closed in order to vary the plasma surface for scaling experiments. Water cooling lines penetrate only the mid-plane port cover/support plate in such a way as to avoid bolted water connections inside the vacuum boundary and at the same time allow blade movement. Both the upper and lower blades are attached to the mid-plane limiter blade through pivots. Pivot connections are protected against arcing with an alumina coating and a shunt bar strap. Remote handling is considered throughout the design

  3. Effect of indirect ohmic heating on quality of ready-to-eat pineapple packed in plastic pouch

    Directory of Open Access Journals (Sweden)

    Hoang Pham

    2014-06-01

    Full Text Available Ready-to-eat fruits packed in sealed containers are highly perishable due to their intrinsic characteristics and lack of full thermal process. Ohmic heating has the advantages of rapid liquid heating through electrical current. The aim of this research was to investigate the effect of indirect ohmic heating on pH, total soluble solids, polyphenol oxidase activity, color and texture of ready-to-eat pineapple packed in a polypropylene pouch with 1% calcium chloride and 0.3% ascorbic acid packing solution. The pre-packed sample in a pouch was placed in the ohmic heating jar filled with 0.5% sodium chloride ohmic heating solution which was then ohmic heated at different voltage gradients (20, 30, 40 V/cm, to different packing solution temperatures (60, 70, 80°C for 60s. Samples were kept at 4°C for quality measurement. It was found that browning index of ready-to-eat pineapple treated with 20 V/cm at 80°C, 30 V/cm at 70°C and 80°C, 40 V/cm at 80°C did not change during 12 days cold storage (p>0.05. Polyphenol oxidase was inactivated when the temperature of the pineapple was 62°C or higher. After 10 days at 4°C, the pineapple heated with 30 V/cm at 70°C had much higher firmness than the un-heated sample kept at the same storage condition. Indirect ohmic heating of pre-packed ready-to-eat pineapple in polypropylene pouch with 30 V/cm at 70°C packing solution temperature for 60s could be used as minimal heating methods to maintain the quality of ready-to-eat fruits in 12 days at 4°C.

  4. Endothelial nitric oxide synthase gene polymorphisms associated ...

    African Journals Online (AJOL)

    STORAGESEVER

    2010-05-24

    May 24, 2010 ... chronic periodontitis (CP), 31 with gingivitis (G) and 50 healthy controls. Probing depth ..... Periodontal disease in pregnancy I. Prevalence and severity. ... endothelial nitric oxide synthase gene in premenopausal women with.

  5. Kinetics of Maillard reactions in model infant formula during UHT treatment using a static batch ohmic heater

    OpenAIRE

    Roux , Stéphanie; Courel , Mathilde; Ait-Ameur , Lamia; Birlouez-Aragon , Inès; Pain , Jean-Pierre

    2009-01-01

    The impact of a UHT treatment on a model infant formula was examined by assessing the advancement of Maillard reactions during a thermal treatment by ohmic heating. The heating and holding steps of the heat treatment were carried out in a static batch ohmic heater equipped with a nitrogen counter-pressure system, allowing reaching five temperature levels from 100 to 140 °C. A heat treatment was characterized by monitoring a holding time at a given temperature. Samples were taken during heatin...

  6. Capacitance measurements and AC conductivity of Nickel Phthalocyanine films

    International Nuclear Information System (INIS)

    Darwish, S.

    2005-01-01

    A C dark Current measurements of nickel phthalocyanine thin films using ohmic gold electrodes are investigated in the frequency range 30-10 Hz and within the temperature range 295-385 K. The A C conductivity as D Ac is found to vary as within the index s < 1, indicating a dominant hopping process at low temperatures. From the temperature dependence of A C conductivity, free carrier conduction with mean activation energy of 0.31 eV is observed at higher temperatures. Capacitance and loss tangent are found to be decreased with increasing frequency and increase with increasing temperature. Such characteristics are found to be in good qualitative agreement with existing equivalent circuit model assuming ohmic contacts

  7. Terpene synthases from Cannabis sativa.

    Directory of Open Access Journals (Sweden)

    Judith K Booth

    Full Text Available Cannabis (Cannabis sativa plants produce and accumulate a terpene-rich resin in glandular trichomes, which are abundant on the surface of the female inflorescence. Bouquets of different monoterpenes and sesquiterpenes are important components of cannabis resin as they define some of the unique organoleptic properties and may also influence medicinal qualities of different cannabis strains and varieties. Transcriptome analysis of trichomes of the cannabis hemp variety 'Finola' revealed sequences of all stages of terpene biosynthesis. Nine cannabis terpene synthases (CsTPS were identified in subfamilies TPS-a and TPS-b. Functional characterization identified mono- and sesqui-TPS, whose products collectively comprise most of the terpenes of 'Finola' resin, including major compounds such as β-myrcene, (E-β-ocimene, (--limonene, (+-α-pinene, β-caryophyllene, and α-humulene. Transcripts associated with terpene biosynthesis are highly expressed in trichomes compared to non-resin producing tissues. Knowledge of the CsTPS gene family may offer opportunities for selection and improvement of terpene profiles of interest in different cannabis strains and varieties.

  8. Terpene synthases from Cannabis sativa.

    Science.gov (United States)

    Booth, Judith K; Page, Jonathan E; Bohlmann, Jörg

    2017-01-01

    Cannabis (Cannabis sativa) plants produce and accumulate a terpene-rich resin in glandular trichomes, which are abundant on the surface of the female inflorescence. Bouquets of different monoterpenes and sesquiterpenes are important components of cannabis resin as they define some of the unique organoleptic properties and may also influence medicinal qualities of different cannabis strains and varieties. Transcriptome analysis of trichomes of the cannabis hemp variety 'Finola' revealed sequences of all stages of terpene biosynthesis. Nine cannabis terpene synthases (CsTPS) were identified in subfamilies TPS-a and TPS-b. Functional characterization identified mono- and sesqui-TPS, whose products collectively comprise most of the terpenes of 'Finola' resin, including major compounds such as β-myrcene, (E)-β-ocimene, (-)-limonene, (+)-α-pinene, β-caryophyllene, and α-humulene. Transcripts associated with terpene biosynthesis are highly expressed in trichomes compared to non-resin producing tissues. Knowledge of the CsTPS gene family may offer opportunities for selection and improvement of terpene profiles of interest in different cannabis strains and varieties.

  9. The role of titanium aluminide in n-gallium nitride ohmic contact technology

    Science.gov (United States)

    Pelto, Christopher M.

    Ohmic contacts are essential to the realization of efficient and affordable nitride-based electronic and optoelectronic devices. Currently, the most successful ohmic contact schemes to n-GaN are based on the Al/Ti bilayer structure, although the mechanism responsible for the low resistance in these contacts is not sufficiently understood. In this work, the intermetallic TiAl3 has been employed both as a model ohmic contact system to help understand the essential features of the Al/Ti standard contact, as well as a thermally stable oxidation cap for the bilayer structure. A quaternary isotherm of the Al-Ti-Ga-N system was calculated at 600°C, which showed that a sufficient phase topology was present to apply the exchange mechanism to the TiAl 3/GaN couple. The exchange mechanism rationalized the selection of the TiAl3 intermetallic by predicting that an Al-rich AlGaN layer will form at the metal/semiconductor interface. As part of the investigation of these novel contact systems, a thorough characterization was undertaken on both a standard Al/Ti and Au/Ni/Al/Ti contact to n-GaN in which the essential processing parameters and metallurgical properties were identified. The TiAl 3 contact was found to exhibit inferior electrical behavior compared to the Al/Ti bilayer, requiring significantly higher annealing temperatures to achieve comparable specific contact resistance. It is conjectured that this is due to the early formation of a TiN layer at the metal/semiconductor interface of the bilayer contact, even though both contacts are suspected to form the Al-rich nitride layer at higher temperature. As an oxidation cap, the TiAl3 metallization was found to provide much improved performance characteristics compared to the four-layer Au/Al/Ni/Ti standard. The TiAl 3/Al/Ti contact proved to achieve optimal performance at a much lower temperature than the standard, and furthermore showed complete insensitivity to the oxidation content of the annealing ambient. Reaction

  10. Achieving Ohmic Contact for High-quality MoS2 Devices on Hexagonal Boron Nitride

    Science.gov (United States)

    Cui, Xu

    MoS2, among many other transition metal dichalcogenides (TMDCs), holds great promise for future applications in nano-electronics, opto-electronics and mechanical devices due to its ultra-thin nature, flexibility, sizable band-gap, and unique spin-valley coupled physics. However, there are two main challenges that hinder careful study of this material. Firstly, it is hard to achieve Ohmic contacts to mono-layer MoS2, particularly at low temperatures (T) and low carrier densities. Secondly, materials' low quality and impurities introduced during the fabrication significantly limit the electron mobility of mono- and few-layer MoS2 to be substantially below theoretically predicted limits, which has hampered efforts to observe its novel quantum transport behaviours. Traditional low work function metals doesn't necessary provide good electron injection to thin MoS2 due to metal oxidation, Fermi level pinning, etc. To address the first challenge, we tried multiple contact schemes and found that mono-layer hexagonal boron nitride (h-BN) and cobalt (Co) provide robust Ohmic contact. The mono-layer spacer serves two advantageous purposes: it strongly interacts with the transition metal, reducing its work function by over 1 eV; and breaks the metal-TMDCs interaction to eliminate the interfacial states that cause Fermi level pinning. We measure a flat-band Schottky barrier of 16 meV, which makes thin tunnel barriers upon doping the channels, and thus achieve low-T contact resistance of 3 kohm.um at a carrier density of 5.3x10. 12/cm. 2. Similar to graphene, eliminating all potential sources of disorder and scattering is the key to achieving high performance in MoS2 devices. We developed a van der Waals heterostructure device platform where MoS2 layers are fully encapsulated within h-BN and electrically contacted in a multi-terminal geometry using gate-tunable graphene electrodes. The h-BN-encapsulation provides excellent protection from environmental factors, resulting in

  11. Establishing an upper bound on contact resistivity of ohmic contacts to n-GaN nanowires

    International Nuclear Information System (INIS)

    Blanchard, Paul; Bertness, Kris A; Harvey, Todd; Sanford, Norman

    2014-01-01

    Contact resistivity ρ c is an important figure of merit in evaluating and improving the performance of electronic and optoelectronic devices. Due to the small size, unique morphology, and uncertain transport properties of semiconductor nanowires (NWs), measuring ρ c of contacts to NWs can be particularly challenging. In this work, Si-doped n-GaN NWs were grown by molecular beam epitaxy. Four-contact structures with 20 nm Ti/200 nm Al contacts were fabricated on individual NWs by photolithography, and the contacts were annealed to achieve ohmic behavior. Two-point resistances R 23  and four-point collinear resistances R 23collinear  were measured between the middle two contacts on each NW. These resistances were then modeled by taking into account the non-uniform distribution of current flow along the length of each contact. Contrary to the assumption that the resistance difference R 23 −R 23collinear  is equal to the total contact resistance R c , the distributed-current-flow contact model shows that R 23 −R 23collinear  ≪ R c when ρ c is sufficiently small. Indeed, the measured R 23 −R 23collinear  was so small in these devices that it was within the measurement uncertainty, meaning that it was not possible to directly calculate ρ c from these data. However, it was possible to calculate an upper bound on ρ c for each device based on the largest possible value of R 23 −R 23collinear . In addition, we took into account the large uncertainties in the NW transport properties by numerically maximizing ρ c with respect to the uncertainty range of each measured and assumed parameter in the contact model. The resulting upper limits on ρ c ranged from 4.2 × 10 −6  to 7.6 × 10 −6  Ω cm 2 , indicating that 20 nm Ti/200 nm Al is a good choice of ohmic contact for moderately-doped n-GaN NWs. The measurement and numerical analysis demonstrated here offer a general approach to modeling ohmic contact resistivity via NW four

  12. D III-D divertor target heat flux measurements during Ohmic and neutral beam heating

    International Nuclear Information System (INIS)

    Hill, D.N.; Petrie, T.; Mahdavi, M.A.; Lao, L.; Howl, W.

    1988-01-01

    Time resolved power deposition profiles on the D III-D divertor target plates have been measured for Ohmic and neutral beam injection heated plasmas using fast response infrared thermography (τ ≤ 150 μs). Giant Edge Localized Modes have been observed which punctuate quiescent periods of good H-mode confinement and deposit more than 5% of the stored energy of the core plasma on the divertor armour tiles on millisecond time-scales. The heat pulse associated with these events arrives approximately 0.5 ms earlier on the outer leg of the divertor relative to the inner leg. The measured power deposition profiles are displaced relative to the separatrix intercepts on the target plates, and the peak heat fluxes are a function of core plasma density. (author). Letter-to-the-editor. 11 refs, 7 figs

  13. Conceptual designs of 50 kA 20 MJ superconducting ohmic heating coils

    International Nuclear Information System (INIS)

    Singh, S.K.; Murphy, J.H.; Janocko, M.A.; Haller, H.E.; Litz, D.C.; Eckels, P.W.; Rogers, J.D.; Thullen, P.

    1979-01-01

    Two designs of 20 Mj superconducting coils are described which were developed to demonstrate the feasibility of an ohmic heating system. NbTi and Nb;sub 3;Sn superconductors were considered for both 7 tesla and 9 tesla maximum fields. Cabled and braided conductors were investigated and the braided conductor is identified as the best alternative due to its high operating current densities and because of its porosity. The coils are designed to be cryostable for bipolar operation from +7 tesla to -7 tesla and from +9 tesla to -9 tesla maximum fields within 1 sec. The structural design addresses the distribution of structure and structural materials used in the pulsed field environment. Immersion cooled (pool boil) and forced flow cooled coils are described. 2 refs

  14. Fokker-Planck equation of the reduced Wigner function associated to an Ohmic quantum Langevin dynamics

    Science.gov (United States)

    Colmenares, Pedro J.

    2018-05-01

    This article has to do with the derivation and solution of the Fokker-Planck equation associated to the momentum-integrated Wigner function of a particle subjected to a harmonic external field in contact with an ohmic thermal bath of quantum harmonic oscillators. The strategy employed is a simplified version of the phenomenological approach of Schramm, Jung, and Grabert of interpreting the operators as c numbers to derive the quantum master equation arising from a twofold transformation of the Wigner function of the entire phase space. The statistical properties of the random noise comes from the integral functional theory of Grabert, Schramm, and Ingold. By means of a single Wigner transformation, a simpler equation than that mentioned before is found. The Wigner function reproduces the known results of the classical limit. This allowed us to rewrite the underdamped classical Langevin equation as a first-order stochastic differential equation with time-dependent drift and diffusion terms.

  15. Evolution of the electron temperature profile of ohmically heated plasmas in TFTR

    International Nuclear Information System (INIS)

    Taylor, G.; Efthimion, P.C.; Arunasalam, V.

    1985-08-01

    Blackbody electron cyclotron emission was used to ascertain and study the evolution and behavior of the electron temperature profile in ohmically heated plasmas in the Tokamak Fusion Test Reactor (TFTR). The emission was measured with absolutely calibrated millimeter wavelength radiometers. The temperature profile normalized to the central temperature and minor radius is observed to broaden substantially with decreasing limiter safety factor q/sub a/, and is insensitive to the plasma minor radius. Sawtooth activity was seen in the core of most TFTR discharges and appeared to be associated with a flattening of the electron temperature profile within the plasma core where q less than or equal to 1. Two types of sawtooth behavior were identified in large TFTR plasmas (minor radius, a less than or equal to 0.8 m) : a typically 35 to 40 msec period ''normal'' sawtooth, and a ''compound'' sawtooth with 70 to 80 msec period

  16. A 1.5 MJ cryostatic stable superconducting ohmic-heating coil

    International Nuclear Information System (INIS)

    Wang, S.-T.; Kim, S.H.; Praeg, W.F.; Krieger, C.I.

    1978-01-01

    As early as FY 1975, ANL had recognized the clear advantage of a superconducting ohmic-heating (OH) coil and proposed a five-year pulsed coil and power supply development program to ERDA. With modest funding made available by ERDA in FY 1977 and the use of substantial equipment inventory at ANL, a small but agressive development program was advanced to the construction of a 1.5 MJ model coil. The principle objective in building the 1.5 MJ ac coil is to demonstrate ac cryostability of a large coil with a dB/dt ranging from 2 T/s up to 14 T/s. The results of basic cable development and tests will be described. The design and construction of a prototype 1.5 MJ cryostable pulsed coil and its nonmetallic cryostat will be presented. (author)

  17. High reflectivity Ohmic contacts to n-GaN utilizing vacuum annealed aluminum

    KAUST Repository

    Yonkee, Benjamin P.; Young, Erin; DenBaars, Steven P; Speck, James S; Nakamura, Shuji

    2017-01-01

    Ohmic contacts to both c-plane and (202 ̅1 ̅) n-GaN are demonstrated using a pure aluminum layer which was vacuum annealed to prevent oxidation. Specific contact resistivities of 4.4 × 10-7 and 2.3 × 10-5 Ωcm2 were obtained without annealing for c-plane and (202 ̅1 ̅ ) samples respectively. A reflectivity of over 85% at 450 nm was measured for both samples. After a 300 °C anneal specific contact resistivities of 1.5 × 10-7 and 1.8 × 10-7 Ωcm2 were obtained for c-plane and (202 ̅1 ̅ ) samples respectively and the reflectivities remained higher than 80%.

  18. High reflectivity Ohmic contacts to n-GaN utilizing vacuum annealed aluminum

    KAUST Repository

    Yonkee, Benjamin P.

    2017-10-31

    Ohmic contacts to both c-plane and (202 ̅1 ̅) n-GaN are demonstrated using a pure aluminum layer which was vacuum annealed to prevent oxidation. Specific contact resistivities of 4.4 × 10-7 and 2.3 × 10-5 Ωcm2 were obtained without annealing for c-plane and (202 ̅1 ̅ ) samples respectively. A reflectivity of over 85% at 450 nm was measured for both samples. After a 300 °C anneal specific contact resistivities of 1.5 × 10-7 and 1.8 × 10-7 Ωcm2 were obtained for c-plane and (202 ̅1 ̅ ) samples respectively and the reflectivities remained higher than 80%.

  19. Optimisation of the Ti/Al/Ni/Au ohmic contact on AlGaN/GaN FET structures

    NARCIS (Netherlands)

    Jacobs, B.; Krämer, M.C.J.C.M.; Geluk, E.J.; Karouta, F.

    2002-01-01

    We present a systematic approach to reduce the resistance of ohmic contacts on AlGaN/GaN FET structures. We have optimised the Ti/Al/Ni/Au contact with respect to the metal composition and annealing conditions. Our optimised contact has a very low contact resistance of 0.2 ohm mm (7.3 x 10^-7 ohm

  20. Influence of infrared final cooking on color, texture and cooking characteristics of ohmically pre-cooked meatball.

    Science.gov (United States)

    Yildiz Turp, Gulen; Icier, Filiz; Kor, Gamze

    2016-04-01

    The objective of the current study was to improve the quality characteristics of ohmically pre-cooked beef meatballs via infrared cooking as a final stage. Samples were pre-cooked in a specially designed-continuous type ohmic cooker at a voltage gradient of 15.26 V/cm for 92 s. Infrared cooking was then applied to the pre-cooked samples at different combinations of heat fluxes (3.706, 5.678, and 8.475 kW/m(2)), application distances (10.5, 13.5, and 16.5 cm) and application durations (4, 8, and 12min). Effects of these parameters on color, texture and cooking characteristics of ohmically pre-cooked beef meatballs were investigated. The appearance of ohmically pre-cooked meatball samples was improved via infrared heating. A dark brown layer desired in cooked meatballs formed on the surface of the meatballs with lowest application distance (10.5 cm) and longest application duration (12 min). The texture of the samples was also improved with these parameters. However the cooking yield of the samples decreased at the longest application duration of infrared heating. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Indium gallium zinc oxide (IGZO)-based Ohmic contact formation on n-type gallium antimony (GaSb)

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Jeong-Hun; Jung, Hyun-Wook [Samsung-SKKU Graphene Center and School of Electronic and Electrical Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Jung, Woo-Shik [Department of Electrical Engineering, Stanford University, Stanford, CA 94305 (United States); Park, Jin-Hong, E-mail: jhpark9@skku.edu [Samsung-SKKU Graphene Center and School of Electronic and Electrical Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

    2014-02-14

    In this paper, Ohmic-like contact on n-type GaSb with on/off-current ratio of 1.64 is presented, which is formed at 500 °C by inserting IGZO between metal (Ni) and GaSb. The resulting Ohmic contact is systematically investigated by TOF-SIMS, HSC chemistry simulation, XPS, TEM, AFM, and J–V measurements. Two main factors contributing to the Ohmic contact formation are (1) InSb (or InGaSb) with narrow energy bandgap (providing low electron and hole barrier heights) formed by In diffusion from IGZO and Sb released by Ga oxidation, and (2) free Sb working as traps that induces tunneling current. - Highlights: • We demonstrate Ohmic-like contact on n-type GaSb with on/off-current ratio of 1.64. • The reverse current is increased by low electron barrier height and high TAT current. • The low electron barrier height is achieved by the formation of InGaSb. • Free Sb atoms also work as traps inducing high TAT current.

  2. Plasma-assisted ohmic contact for AlGaN/GaN heterostructure field-effect transistors

    International Nuclear Information System (INIS)

    Zhang, Jiaqi; Wang, Lei; Wang, Qingpeng; Jiang, Ying; Li, Liuan; Ao, Jin-Ping; Zhu, Huichao

    2016-01-01

    An Al-based ohmic process assisted by an inductively coupled plasma (ICP) recess treatment is proposed for AlGaN/GaN heterostructure field-effect transistors (HFETs) to realize ohmic contact, which is only needed to anneal at 500 °C. The recess treatment was done with SiCl 4 plasma with 100 W ICP power for 20 s and annealing at 575 °C for 1 min. Under these conditions, contact resistance of 0.52 Ωmm was confirmed. To suppress the ball-up phenomenon and improve the surface morphology, an Al/TiN structure was also fabricated with the same conditions. The contact resistance was further improved to 0.30 Ωmm. By using this plasma-assisted ohmic process, a gate-first HFET was fabricated. The device showed high drain current density and high transconductance. The leakage current of the TiN-gate device decreased to 10 −9 A, which was 5 orders of magnitude lower than that of the device annealed at 800 °C. The results showed that the low-temperature ohmic contact process assisted by ICP treatment is promising for the fabrication of gate-first and self-aligned gate HFETs. (paper)

  3. Enhanced TiC/SiC Ohmic contacts by ECR hydrogen plasma pretreatment and low-temperature post-annealing

    International Nuclear Information System (INIS)

    Liu, Bingbing; Qin, Fuwen; Wang, Dejun

    2015-01-01

    Highlights: • Low-temperature ECR microwave hydrogen plasma were pretreated for moderately doped (1 × 10"1"8 cm"−"3) SiC surfaces. • The relationship among Ohmic properties, the SiC surface properties and TiC/SiC interface properties were established. • Interface band structures were analyzed to elucidate the mechanism by which the Ohmic contacts were formed. - Abstract: We proposed an electronic cyclotron resonance (ECR) microwave hydrogen plasma pretreatment (HPT) for moderately doped (1 × 10"1"8 cm"−"3) SiC surfaces and formed ideal TiC/SiC Ohmic contacts with significantly low contact resistivity (1.5 × 10"−"5 Ω cm"2) after low-temperature annealing (600 °C). This is achieved by reducing barrier height at TiC/SiC interface because of the release of pinned Fermi level by surface flattening and SiC surface states reduction after HPT, as well as the generation of donor-type carbon vacancies, which reduced the depletion-layer width for electron tunneling after annealing. Interface band structures were analyzed to elucidate the mechanism of Ohmic contact formations.

  4. Design of a multistage 250 kJ capacitor bank for ohmic transformer of tokamak ''ADITYA''

    International Nuclear Information System (INIS)

    Sathyanarayana, K.; Saxena, Y.C.; John, P.I.; Pujara, H.D.; Jain, K.K.

    1993-01-01

    Tokamaks require toroidal loop voltage for breakdown of the neutral gas, current rise, and the flat top phase. The temporal profile of the loop voltage established by the change of flux linked by the ohmic transformer has to be a noncosine waveform. In this paper a multistage capacitor bank is described which was used to energize the ohmic transformer in tokamak ADITYA with a major radius of 0.75 m, minor radius of 0.25 m, and a toroidal field of 1.5 T at the plasma center. A combination of capacitors charged to different voltages are switched in at appropriate times, to realize an experimental demand for initial high loop voltage followed by a lower sustaining loop voltage. Theoretical prediction for the duration of the secondary loop voltage as a function of circuit parameters, for a fast bank operation of 6 kV, slow bank, 4--4.5 kV, and slow bank, 2--2.5 kV yield t 0 =1.25 mS, t 1 =4.95 mS, and t 2 =24.1 mS. These values are in close agreement to the measured values of t 0 =1.39 mS, t 1 =5.7 mS, and t 2 =23.7 mS. The trigger delays to the various capacitor bank sections are parameter dependent. To avoid repetitive adjustments in the delays, a novel scheme for consistent triggering is also highlighted

  5. Bayesian Analysis of Hot-Jupiter Radius Anomalies: Evidence for Ohmic Dissipation?

    Science.gov (United States)

    Thorngren, Daniel P.; Fortney, Jonathan J.

    2018-05-01

    The cause of hot-Jupiter radius inflation, where giant planets with {T}eq} > 1000 K are significantly larger than expected, is an open question and the subject of many proposed explanations. Many of these hypotheses postulate an additional anomalous power that heats planets’ convective interiors, leading to larger radii. Rather than examine these proposed models individually, we determine what anomalous powers are needed to explain the observed population’s radii, and consider which models are most consistent with this. We examine 281 giant planets with well-determined masses and radii and apply thermal evolution and Bayesian statistical models to infer the anomalous power as a fraction of (and varying with) incident flux ɛ(F) that best reproduces the observed radii. First, we observe that the inflation of planets below about M = 0.5 M J appears very different than their higher-mass counterparts, perhaps as the result of mass loss or an inefficient heating mechanism. As such, we exclude planets below this threshold. Next, we show with strong significance that ɛ(F) increases with {T}eq} toward a maximum of ∼2.5% at T eq ≈ 1500 K, and then decreases as temperatures increase further, falling to ∼0.2% at T eff = 2500 K. This high-flux decrease in inflation efficiency was predicted by the Ohmic dissipation model of giant planet inflation but not other models. We also show that the thermal tides model predicts far more variance in radii than is observed. Thus, our results provide evidence for the Ohmic dissipation model and a functional form for ɛ(F) that any future theories of hot-Jupiter radii can be tested against.

  6. Measurement of the drift velocities of electrons and holes in high-ohmic silicon

    International Nuclear Information System (INIS)

    Scharf, Christian

    2014-02-01

    Measurements of the drift velocities of electrons and holes as a function of the electric field and the temperature in high-ohmic silicon of crystal orientation are presented. Significant differences between our results and literature values are observed. A new parametrization of the mobility is introduced. Current transients of n-type pad diodes, generated by fast laser pulses, were investigated in order to determine the drift velocity of electrons and holes separately. Two diodes of high-ohmic silicon (1.5 kΩcm and 5.5 kΩcm) from different manufacturers were investigated as cross check. The drift velocities were determined at electric fields ranging from 5 kV/cm to 50 kV/cm at temperatures ranging from 233 K to 333 K. The mobility parameters were obtained by fitting a simulation of charge drift in silicon to the measurements. Using the convolution theorem the response function of the read-out circuit was determined with the Fourier transforms of the measurement and the simulation. The simulated transient current pulses with the new mobility parametrization are consistent with the measured ones for the temperature and electric field range investigated here. Additionally, the mobility results from the fit are consistent with the mobility determined using the simpler time-of-flight method in the field range where this method is applicable. However, our measurements show a difference of up to 14 % to the values by Canali et al. (1971). The difference to the mobility parametrization by Jacoboni et al. (1977) is up to 24 % while this parametrization is widely used for simulations of the direction due to the lack of data for silicon.

  7. Initial Thomson Scattering Survey of Local Helicity Injection and Ohmic Plasmas at the Pegasus Toroidal Experiment

    Science.gov (United States)

    Schlossberg, D. J.; Bodner, G. M.; Bongard, M. W.; Fonck, R. J.; Winz, G. R.

    2014-10-01

    A multipoint Thomson scattering diagnostic has recently been installed on the Pegasus ST. The system utilizes a frequency-doubled Nd:YAG laser (λ0 ~ 532 nm), spectrometers with volume phase holographic gratings, and a gated, intensified CCD camera. It provides measurements of Te and ne at 8 spatial locations for each spectrometer once per discharge. A new multiple aperture and beam dump system has been implemented to mitigate interference from stray light. This system has provided initial measurements in the core region of plasmas initiated by local helicity injection (LHI), as well as conventional Ohmic L- and H-mode discharges. Multi-shot averages of low-density (ne ~ 3 ×1018 m-3) , Ip ~ 0 . 1 MA LHI discharges show central Te ~ 75 eV at the end of the helicity injection phase. Ip ~ 0 . 13 MA Ohmic plasmas at moderate densities (ne ~ 2 ×1019 m-3) have core Te ~ 150 eV in L-mode. Generally, these plasmas do not reach transport equilibrium in the short 25 ms pulse length available. After an L-H transition, strong spectral broadening indicates increasing Te, to values above the range of the present spectrometer system with a high-dispersion VPH grating. Near-term system upgrades will focus on deploying a second spectrometer, with a lower-dispersion grating capable of measuring the 0.1-1.0 keV range. The second spectrometer system will also increase the available number of spatial channels, enabling study of H-mode pedestal structure. Work supported by US DOE Grant DE-FG02-96ER54375.

  8. Device for the measurement of electrically conductive bulk goods led through a pipeline

    International Nuclear Information System (INIS)

    Thyssen, H.; Breuer, G.

    1978-01-01

    The measuring section employed to detect the passage of spherical, graphite coated, electrically conducting fuel and/or blanket elements consists of a metal tube as the first electrode and another electrode, which is insulated from the first one, between which a spark gap is triggered by a sphere passing between them. The circuitry of the two electrodes includes a DC generator and a high ohmic resistor. The indication signals are generated by amplitude modulation by the interaction of the high ohmic resistor, the spark gap and a stray capacitance connected in parallel with the spark gap. The signals can be fed to the data processing system. (RW) [de

  9. Quantitative comparison of electron temperature fluctuations to nonlinear gyrokinetic simulations in C-Mod Ohmic L-mode discharges

    Energy Technology Data Exchange (ETDEWEB)

    Sung, C., E-mail: csung@physics.ucla.edu [University of California, Los Angeles, Los Angeles, California 90095 (United States); White, A. E.; Greenwald, M.; Howard, N. T. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Mikkelsen, D. R.; Churchill, R. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States); Holland, C. [University of California, San Diego, La Jolla, California 92093 (United States); Theiler, C. [Ecole Polytechnique Fédérale de Lausanne, SPC, Lausanne 1015 (Switzerland)

    2016-04-15

    Long wavelength turbulent electron temperature fluctuations (k{sub y}ρ{sub s} < 0.3) are measured in the outer core region (r/a > 0.8) of Ohmic L-mode plasmas at Alcator C-Mod [E. S. Marmar et al., Nucl. Fusion 49, 104014 (2009)] with a correlation electron cyclotron emission diagnostic. The relative amplitude and frequency spectrum of the fluctuations are compared quantitatively with nonlinear gyrokinetic simulations using the GYRO code [J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003)] in two different confinement regimes: linear Ohmic confinement (LOC) regime and saturated Ohmic confinement (SOC) regime. When comparing experiment with nonlinear simulations, it is found that local, electrostatic ion-scale simulations (k{sub y}ρ{sub s} ≲ 1.7) performed at r/a ∼ 0.85 reproduce the experimental ion heat flux levels, electron temperature fluctuation levels, and frequency spectra within experimental error bars. In contrast, the electron heat flux is robustly under-predicted and cannot be recovered by using scans of the simulation inputs within error bars or by using global simulations. If both the ion heat flux and the measured temperature fluctuations are attributed predominantly to long-wavelength turbulence, then under-prediction of electron heat flux strongly suggests that electron scale turbulence is important for transport in C-Mod Ohmic L-mode discharges. In addition, no evidence is found from linear or nonlinear simulations for a clear transition from trapped electron mode to ion temperature gradient turbulence across the LOC/SOC transition, and also there is no evidence in these Ohmic L-mode plasmas of the “Transport Shortfall” [C. Holland et al., Phys. Plasmas 16, 052301 (2009)].

  10. Bacillus caldolyticus prs gene encoding phosphoribosyldiphosphate synthase

    DEFF Research Database (Denmark)

    Krath, Britta N.; Hove-Jensen, Bjarne

    1996-01-01

    The prs gene, encoding phosphoribosyl-diphosphate (PRPP) synthase, as well as the flanking DNA sequences were cloned and sequenced from the Gram-positive thermophile, Bacillus caldolyticus. Comparison with the homologous sequences from the mesophile, Bacillus subtilis, revealed a gene (gca......D) encoding N-acetylglucosamine-l-phosphate uridyltransferase upstream of prs, and a gene homologous to ctc downstream of prs. cDNA synthesis with a B. caldolyticus gcaD-prs-ctc-specified mRNA as template, followed by amplification utilising the polymerase chain reaction indicated that the three genes are co......-transcribed. Comparison of amino acid sequences revealed a high similarity among PRPP synthases across a wide phylogenetic range. An E. coli strain harbouring the B. caldolyticus prs gene in a multicopy plasmid produced PRPP synthase activity 33-fold over the activity of a haploid B. caldolyticus strain. B. caldolyticus...

  11. Current Spreading Layer with High Transparency and Conductivity for near-ultraviolet light emitting diodes

    DEFF Research Database (Denmark)

    Lin, Li; Jensen, Flemming; Herstrøm, Berit

    Transparent conductive aluminum-doped zinc oxide (AZO) layer was deposited on GaN-based near-ultraviolet (NUV) light emitting epitaxial wafers as current spreading layer by a sputtering process. Efforts were made to improve the electrical properties of AZO in order to produce ohmic contact....

  12. Methionine synthase A2756G and reduced folate carrier1 A80G ...

    African Journals Online (AJOL)

    Aim of the study: To analyze the effect of methionine synthase (MTR) A2756G, and reduced folate carrier (RFC1) A80G gene polymorphisms on the maternal risk for DS. Patients: This study was conducted in the Medical Genetics Center, Ain-Shams University hospitals, on a total of 170 mothers of children, diagnosed with ...

  13. Cloning and expression of pineapple sucrosephosphate synthase ...

    African Journals Online (AJOL)

    A 1132-base pairs (bp) polymerase-chain-reaction product of sucrose-phosphate synthase (SPS) (EC 2.3.1.14) from pineapple (Ananas comosus cv. Comte de paris) fruit was cloned and nominated as Ac- SPS1. The sequence encodes a putative 377 amino acids protein containing two serine conserved features that had ...

  14. Endothelial nitric oxide synthase gene polymorphisms associated ...

    African Journals Online (AJOL)

    Endothelial nitric oxide synthase (NOS3) is involved in key steps of immune response. Genetic factors predispose individuals to periodontal disease. This study's aim was to explore the association between NOS3 gene polymorphisms and clinical parameters in patients with periodontal disease. Genomic DNA was obtained ...

  15. HAEM SYNTHASE AND COBALT PORPHYRIN SYNTHASE IN VARIOUS MICRO-ORGANISMS.

    Science.gov (United States)

    PORRA, R J; ROSS, B D

    1965-03-01

    1. The preparation of a crude extract of Clostridium tetanomorphum containing cobalt porphyrin synthase but little haem-synthase activity is described. 2. The properties of cobalt porphyrin synthase in the clostridial extracts is compared with the properties of a haem synthase present in crude extracts of the yeast Torulopsis utilis. 3. Cobalt porphyrin synthase in extracts of C. tetanomorphum inserts Co(2+) ions into the following dicarboxylic porphyrins in descending order of rate of insertion: meso-, deutero- and proto-porphyrins. Esterification renders meso- and deutero-porphyrins inactive as substrates. Neither the tetracarboxylic (coproporphyrin III) nor the octacarboxylic (uroporphyrin III) compounds are converted into cobalt porphyrins by the extract, but the non-enzymic incorporation of Co(2+) ions into these two porphyrins is rapid. These extracts are unable to insert Mn(2+), Zn(2+), Mg(2+) or Cu(2+) ions into mesoporphyrin. 4. Crude extracts of T. utilis readily insert both Co(2+) and Fe(2+) ions into deutero-, meso, and proto-porphyrins. Unlike the extracts of C. tetanomorphum, these preparations catalyse the insertion of Co(2+) ions into deuteroporphyrin more rapidly than into mesoporphyrin. This parallels the formation of haems by the T. utilis extract. 5. Cobalt porphyrin synthase is present in the particulate fraction of the extracts of C. tetanomorphum but requires a heat-stable factor present in the soluble fraction. This soluble factor can be replaced by GSH. 6. Cobalt porphyrin synthase in the clostridial extract is inhibited by iodoacetamide and to a smaller extent by p-chloromercuribenzoate and N-ethylmaleimide. The haem synthases of T. utilis and Micrococcus denitrificans are also inhibited by various thiol reagents.

  16. Two-step deposition of Al-doped ZnO on p-GaN to form ohmic contacts

    Science.gov (United States)

    Su, Xi; Zhang, Guozhen; Wang, Xiao; Chen, Chao; Wu, Hao; Liu, Chang

    2017-07-01

    Al-doped ZnO (AZO) thin films were deposited directly on p-GaN substrates by using a two-step deposition consisting of polymer assisted deposition (PAD) and atomic layer deposition (ALD) methods. Ohmic contacts of the AZO on p-GaN have been formed. The lowest sheet resistance of the two-step prepared AZO films reached to 145 Ω/sq, and the specific contact resistance reduced to 1.47 × 10-2 Ω·cm2. Transmittance of the AZO films remained above 80% in the visible region. The combination of PAD and ALD technique can be used to prepare p-type ohmic contacts for optoelectronics.

  17. Evolution of Electrically Active Defects in n-GaN During Heat Treatment Typical for Ohmic Contact Formation

    DEFF Research Database (Denmark)

    Boturchuk, Ievgen; Scheffler, Leopold Julian; Larsen, Arne Nylandsted

    2018-01-01

    Ohmic contact formation to n-type GaN often involves high temperature steps, for example sintering at about 800 °C in the case of Ti-based contacts. Such processing steps might cause changes in the distribution, concentration, and properties of the defects. The present work aims at contributing...... to the knowledge about defect evolution in GaN upon processing at different temperatures. The processing temperatures are selected according to fabrication procedures for commonly used ohmic contacts to n-GaN: 300 °C (In-based), 550 °C (Ta-based), and 800 °C (Ti-based). Properties and concentration of the defects...

  18. Enhancement of ohmic and stochastic heating by resonance effects in capacitive radio frequency discharges: a theoretical approach.

    Science.gov (United States)

    Mussenbrock, T; Brinkmann, R P; Lieberman, M A; Lichtenberg, A J; Kawamura, E

    2008-08-22

    In low-pressure capacitive radio frequency discharges, two mechanisms of electron heating are dominant: (i) Ohmic heating due to collisions of electrons with neutrals of the background gas and (ii) stochastic heating due to momentum transfer from the oscillating boundary sheath. In this work we show by means of a nonlinear global model that the self-excitation of the plasma series resonance which arises in asymmetric capacitive discharges due to nonlinear interaction of plasma bulk and sheath significantly affects both Ohmic heating and stochastic heating. We observe that the series resonance effect increases the dissipation by factors of 2-5. We conclude that the nonlinear plasma dynamics should be taken into account in order to describe quantitatively correct electron heating in asymmetric capacitive radio frequency discharges.

  19. Facet formation and ohmic contacts for laser diodes on non- and semipolar GaN

    Energy Technology Data Exchange (ETDEWEB)

    Rass, Jens; Ploch, Simon; Vogt, Patrick [Technische Universitaet Berlin (Germany). Institute of Solid State Physics; Wernicke, Tim; Redaelli, Luca; Einfeldt, Sven [Ferdinand- Braun-Institut fuer Hoechstfrequenztechnik, Berlin (Germany); Kneissl, Michael [Technische Universitaet Berlin (Germany). Institute of Solid State Physics; Ferdinand- Braun-Institut fuer Hoechstfrequenztechnik, Berlin (Germany)

    2009-07-01

    Group-III-Nitride heterostructures grown on nonpolar and semipolar planes allow the realization of highly efficient devices such as laser diodes and LEDs due to the reduction or elimination of the quantum confined Stark effect. However, the realization of these devices poses a number of challenges, in particular the formation of smooth laser facets and the fabrication of ohmic contacts. In this talk optimized schemes for facet formation and contact resistance reduction for nitride based devices on non- and semipolar planes are presented, and various concepts are discussed. We discuss a laser scribing process that allows the cleaving of facets along the c- and a-plane for devices grown on nonpolar substrates. For semipolar planes there is no low-index cleavage plane in order to form resonators along the projection of the c-axis. Therefore we have investigated etching techniques in order to produce flat facets perpendicular to the plane of growth. For the challenging formation of p-type contacts to GaN we discuss different methods such as chemical treatments, different metallization schemes and capping layers to reduce the contact resistivity.

  20. Radiation, impurity effects, instability characteristics and transport in Ohmically heated plasmas in the PLT tokamak

    International Nuclear Information System (INIS)

    Bol, K.; Arunasalam, V.; Bitter, M.

    1979-01-01

    Titanium-gettered deuterium plasmas, with graphite or steel limiters to define the plasma minor radius, have Zsub(eff) approximately 1 for 3x10 13 14 cm -3 . In ungettered discharges the density limit set by disruptions is about half the value in gettered discharges. The bolometrically measured energy flux from the whole plasma volume is 80-100% of the Ohmic input power for ungettered discharges and 50-70% for gettered ones. The strucutre of MHD modes continues to be intensively studied by means of soft X-ray detector arrays; however, the connection with the disruptive instability remains unclear. Microinstabilities, studied by means of a 2-mm homodyne scattering system, appear to be of sufficient magnitude to influence energy and particle transport. Ion energy confinement times in the central region of the plasma have been estimated to be 50-100ms. Gross electron energy confinement time increases linearly with density at constant temperature. The longest electron energy confinement times observed are approximately >40ms in dense gettered discharges, giving total energy confinement times approximately 80ms. (author)

  1. Power deposition to the pump limiters in Tore-Supra with ohmic plasmas

    International Nuclear Information System (INIS)

    Guilhem, D.; Chatelier, M.; Chappuis Fleury, I.; Klepper, C.

    1990-01-01

    The modification of power scrape-off-length, λq, and power deposition are studied both with the horizontal limiter alone and with the full set of 7 pump limiters for 1MW ohmic plasmas in TORE-SUPRA. By making spatially resolved infrared surface temperature measurements during the plasma discharge, the magnitude and distribution of the energy flux can be derived. For comparison, the surface temperature of the horizontal pump limiter is calculated with a finite element code using a 3D description of the field lines, an exponential scrape-off-layer, and the pump limiter geometry. From comparison of the infrared images of the limiter we derived that the λq for power deposition was slightly less than 9 mm (±1mm) which is in agreement with the predicted design value of 10 mm. For an 8 seconds discharge, the maximum surface temperature on the horizontal limiter is 450 0 C. Inserting the 7 limiters does not modify λq (which becomes 10 mm). The power is shared by all the limiters and the maximum surface temperature on the horizontal limiter decreased to 320 0 C. These λq values have been independently measured by the integrated energy deposition on the horizontal limiter and other internal structures 5 cm into the scrape-off layer. These values agree with the infrared measurements in the two cases

  2. On the breakdown modes and parameter space of Ohmic Tokamak startup

    Science.gov (United States)

    Peng, Yanli; Jiang, Wei; Zhang, Ya; Hu, Xiwei; Zhuang, Ge; Innocenti, Maria; Lapenta, Giovanni

    2017-10-01

    Tokamak plasma has to be hot. The process of turning the initial dilute neutral hydrogen gas at room temperature into fully ionized plasma is called tokamak startup. Even with over 40 years of research, the parameter ranges for the successful startup still aren't determined by numerical simulations but by trial and errors. However, in recent years it has drawn much attention due to one of the challenges faced by ITER: the maximum electric field for startup can't exceed 0.3 V/m, which makes the parameter range for successful startup narrower. Besides, this physical mechanism is far from being understood either theoretically or numerically. In this work, we have simulated the plasma breakdown phase driven by pure Ohmic heating using a particle-in-cell/Monte Carlo code, with the aim of giving a predictive parameter range for most tokamaks, even for ITER. We have found three situations during the discharge, as a function of the initial parameters: no breakdown, breakdown and runaway. Moreover, breakdown delay and volt-second consumption under different initial conditions are evaluated. In addition, we have simulated breakdown on ITER and confirmed that when the electric field is 0.3 V/m, the optimal pre-filling pressure is 0.001 Pa, which is in good agreement with ITER's design.

  3. Al and Cu Implantation into Silicon Substrate for Ohmic Contact in Solar Cell Fabrication

    International Nuclear Information System (INIS)

    Sri Sulamdari; Sudjatmoko; Wirjoadi; Yunanto; Bambang Siswanto

    2002-01-01

    Research on the implantation of Al and Cu ions into silicon substrate for ohmic contact in solar cell fabrication has been carried using ion accelerator machine. Al and Cu ions are from 98% Al and 99.9% Cu powder ionized in ion source system. provided in ion implantor machine. Before implantation process, (0.5 x 1) cm 2 N type and P type silicon were washed in water and then etched in Cp-4A solution. After that, P type silicon were implanted with Al ions and N type silicon were implanted with Cu ions with the ions dose from 10 13 ion/cm 2 - 10 16 ion/cm 2 and energy 20 keV - 80 keV. Implanted samples were then annealed at temperature 400 o C - 850 o C. Implanted and annealed samples were characterized their resistivities using four point probe FPP-5000. It was found that at full electrically active conditions the ρ s for N type was 1.30 x 10 8 Ω/sq, this was achieved at ion dose 10 13 ion/cm 2 and annealing temperature 500 o C. While for P type, the ρ s was 1.13 x 10 2 Ω/sq, this was achieved at ion dose 10 13 ion/cm 2 and energy 40 keV, and annealing temperature 500 o C. (author)

  4. Study of internal transport barriers in the initial phase of Ohmic discharges in TUMAN-3M

    International Nuclear Information System (INIS)

    Askinazi, L G; Bulanin, V V; Vildjunas, M I; Golant, V E; Gorokhov, M V; Kornev, V A; Krikunov, S V; Lebedev, S V; Petrov, A V; Rozhdestvensky, V V; Tukachinsky, A S; Zhubr, N A

    2004-01-01

    A regime with electron heat confinement improvement was recently found in the initial phase of discharges in the TUMAN-3M tokamak. An internal transport barrier (ITB) formation in this regime was confirmed by Thomson scattering measurements and by transport modelling. Two possible reasons for the ITB formation are discussed in the paper: by reduction of turbulent transport in the presence of low magnetic shear or by plasma sheared rotation. It is demonstrated that low magnetic shear formation is possible in the current ramp-up phase of the Ohmic discharge. The low magnetic shear does not seem to be the only reason for the transport reduction. Results of Doppler reflectometry measurements of poloidal rotation of density fluctuations are presented. It is found that core confinement improvement correlates with the appearance of sheared rotation of the density fluctuations and with a burst of the MHD activity. The ITB formation in the regime seems to be a result of a combined action of reduced magnetic shear and plasma sheared rotation

  5. Nonlinear error-field penetration in low density ohmically heated tokamak plasmas

    International Nuclear Information System (INIS)

    Fitzpatrick, R

    2012-01-01

    A theory is developed to predict the error-field penetration threshold in low density, ohmically heated, tokamak plasmas. The novel feature of the theory is that the response of the plasma in the vicinity of the resonant surface to the applied error-field is calculated from nonlinear drift-MHD (magnetohydrodynamical) magnetic island theory, rather than linear layer theory. Error-field penetration, and subsequent locked mode formation, is triggered once the destabilizing effect of the resonant harmonic of the error-field overcomes the stabilizing effect of the ion polarization current (caused by the propagation of the error-field-induced island chain in the local ion fluid frame). The predicted scaling of the error-field penetration threshold with engineering parameters is (b r /B T ) crit ∼n e B T -1.8 R 0 -0.25 , where b r is the resonant harmonic of the vacuum radial error-field at the resonant surface, B T the toroidal magnetic field-strength, n e the electron number density at the resonant surface and R 0 the major radius of the plasma. This scaling—in particular, the linear dependence of the threshold with density—is consistent with experimental observations. When the scaling is used to extrapolate from JET to ITER, the predicted ITER error-field penetration threshold is (b r /B T ) crit ∼ 5 × 10 −5 , which just lies within the expected capabilities of the ITER error-field correction system. (paper)

  6. Temperature dependent diffusion and epitaxial behavior of oxidized Au/Ni/p-GaN ohmic contact

    International Nuclear Information System (INIS)

    Hu, C.Y.; Qin, Z.X.; Feng, Z.X.; Chen, Z.Z.; Ding, Z.B.; Yang, Z.J.; Yu, T.J.; Hu, X.D.; Yao, S.D.; Zhang, G.Y.

    2006-01-01

    The temperature dependent diffusion and epitaxial behavior of oxidized Au/Ni/p-GaN ohmic contact were studied with Rutherford backscattering spectroscopy/channeling (RBS/C) and synchrotron X-ray diffraction (XRD). It is found that the Au diffuses to the surface of p-GaN to form an epitaxial structure on p-GaN after annealing at 450 deg. C. At the same time, the O diffuses to the metal-semiconductor interface and forms NiO. Both of them are suggested to be responsible for the sharp decrease in the specific contact resistance (ρ c ) at 450 deg. C. At 500 deg. C, the epitaxial structure of Au develops further and the O also diffuses deeper into the interface. As a result, the ρ c reaches the lowest value at this temperature. However, when annealing temperature reaches 600 deg. C, part or all of the interfacial NiO is detached from the p-GaN and diffuses out, which cause the ρ c to increase greatly

  7. Radiation losses and global energy balance for Ohmically heated discharges in ASDEX

    International Nuclear Information System (INIS)

    Mueller, E.R.; Behringer, K.; Niedermeyer, H.

    1982-01-01

    Global energy balance, radiation profiles and dominant impurity radiation sources are compared for Ohmically heated limiter and divertor discharges in the ASDEX tokamak. In discharges with a poloidal stainless-steel limiter, total radiation from the plasma is the dominant energy loss channel. The axisymmetric divertor reduces this volume-integrated radiation to 30-35% of the heating power and additional Ti-gettering halves it again to 10-15%. Local radiation losses in the plasma centre, which are mainly due to the presence of iron impurity ions, are reduced by about one order of magnitude. In high-current (Isub(p) = 400 kA) and high-density (nsub(e)-bar = 6 x 10 13 cm -3 ) ungettered divertor discharges, up to 55% of the heating power is dumped into a cold-gas target inside the divertor chambers. The bolometrically detected volume power losses in the chambers can mainly be attributed to neutral hydrogen atoms with kinetic energies of a few eV. In this parameter range, the divertor plasma is dominated by inelastic molecular and atomic processes, the main process being Franck-Condon dissociation of H 2 molecules. (author)

  8. Ti/Al Ohmic Contacts to n-Type GaN Nanowires

    Directory of Open Access Journals (Sweden)

    Gangfeng Ye

    2011-01-01

    Full Text Available Titanium/aluminum ohmic contacts to tapered n-type GaN nanowires with triangular cross-sections were studied. To extract the specific contact resistance, the commonly used transmission line model was adapted to the particular nanowire geometry. The most Al-rich composition of the contact provided a low specific contact resistance (mid 10−8 Ωcm2 upon annealing at 600 °C for 15 s, but it exhibited poor thermal stability due to oxidation of excess elemental Al remaining after annealing, as revealed by transmission electron microscopy. On the other hand, less Al-rich contacts required higher annealing temperatures (850 or 900 °C to reach a minimum specific contact resistance but exhibited better thermal stability. A spread in the specific contact resistance from contact to contact was tentatively attributed to the different facets that were contacted on the GaN nanowires with a triangular cross-section.

  9. Decoherence plus spontaneous symmetry breakdown generate the ''ohmic'' view of the state-vector collapse

    International Nuclear Information System (INIS)

    Ne'eman, Y.; Univ. of Texas, Austin, TX

    1993-06-01

    The collapse of the state-vector is described as a phase transition due to three features. First, there is the atrophying of indeterminacy for macroscopic objects -- including the measurement apparatus. Secondly, there is the environment decohering mechanism, as described by Zeh, Joos and others -- dominant in macroscopic objects. As a result, the classical background, an input in the Copenhagen prescriptions, is generated as an ''effective'' picture, similar to the ''effective'' introduction of Ohmic resistance or of thermodynamical variables, when going from the micro to the macroscopic; in this case, the collectivized substrate is provided by the multiplicity of photon scatterings, etc., on top of the effect of the large number of particles in macroscopic objects. Thirdly, there is the Everett ''branching'', i.e. the materialization of one of the now decoherent states, accompanied by the destruction of the other branches. By definition, quantum indeterminancy represents a symmetry; in a measurement, or in a branching, this symmetry is broken ''spontaneously'', involving a Ginzburg-Landau type potential with asymmetric minima, thus concretizing the quantum ''dice'' without the burden of ''many worlds''. The authors review and systematize the various phase transitions relating quantum to classical phenomena

  10. Confinement of ohmically heated plasmas and turbulent heating in high-magnetic field tokamak TRIAM-1

    Energy Technology Data Exchange (ETDEWEB)

    Hiraki, N; Itoh, S; Kawai, Y; Toi, K; Nakamura, K [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

    1979-12-01

    TRIAM-1, the tokamak device with high toroidal magnetic field, has been constructed to establish the scaling laws of advanced tokamak devices such as Alcator, and to study the possibility of the turbulent heating as a further economical heating method of the fusion oriented plasmas. The plasma parameters obtained by ohmic heating alone are as follows; central electron temperature T sub(e0) = 640 eV, central ion temperature T sub(i0) = 280 eV and line-average electron density n average sub(e) = 2.2 x 10/sup 14/ cm/sup -3/. The empirical scaling laws are investigated concerning T sub(e0), T sub(i0) and n average sub(e). The turbulent heating has been carried out by applying the high electric field in the toroidal direction to the typical tokamak discharge with T sub(i0) asymptotically equals 200 eV. The efficient ion heating is observed and T sub(i0) attains to about 600 eV.

  11. Limits on the field of ohmic heating solenoids, applied to a tokamak TNS

    International Nuclear Information System (INIS)

    Turner, L.R.

    1977-01-01

    If the ohmic heating solenoid for the TNS or other large tokamak is an ungraded cryostable superconducting solenoid, with NbTi at 4.2 K as the superconductor, then the smallest outer diameter is not achieved at the highest attainable field. There is a lower optimum field which minimizes the outer diameter for a given volt-second requirement. At higher fields the mean diameter decreases; but the high fields require more superconductor, more copper stabilizer, more stainless steel for support, and more liquid helium coolant. For the GA-ANL design for TNS, the optimum field is 7.55 T and the minimum outside diameter for the solenoid is 2.15 m. If, on the other hand, the solenoid is graded, with more NbTi, copper, and stainless steel on the inner turns where the field is higher, than the volt-seconds can always be increased, for a given outer diameter, by adding more turns at a higher field inside until either the critical field is reached or the solenoid bore is filled. However, the material and money required to add a few more volt-seconds increases rapidly with field

  12. Plasma interaction with tungsten samples in the COMPASS tokamak in ohmic ELMy H-modes

    International Nuclear Information System (INIS)

    Dimitrova, M; Weinzettl, V; Matejicek, J; Dejarnac, R; Stöckel, J; Havlicek, J; Panek, R; Popov, Tsv; Marinov, S; Costea, S

    2016-01-01

    This paper reports experimental results on plasma interaction with tungsten samples with or without pre-grown He fuzz. Under the experimental conditions, arcing was observed on the fuzzy tungsten samples, resulting in localized melting of the fuzz structure that did not extend into the bulk. The parallel power flux densities were obtained from the data measured by Langmuir probes embedded in the divertor tiles on the COMPASS tokamak. Measurements of the current-voltage probe characteristics were performed during ohmic ELMy H-modes reached in deuterium plasmas at a toroidal magnetic field B T = 1.15 T, plasma current I p = 300 kA and line-averaged electron density n e = 5×10 19 m -3 . The data obtained between the ELMs were processed by the recently published first-derivative probe technique for precise determination of the plasma potential and the electron energy distribution function (EEDF). The spatial profile of the EEDF shows that at the high-field side it is Maxwellian with a temperature of 5 -- 10 eV. The electron temperatures and the ion-saturation current density obtained were used to evaluate the radial distribution of the parallel power flux density as being in the order of 0.05 -- 7 MW/m 2 . (paper)

  13. Limits on the field of ohmic heating solenoids, applied to a tokamak TNS

    International Nuclear Information System (INIS)

    Turner, L.R.

    1978-01-01

    If the ohmic heating solenoid for the TNS or other large tokamak is an ungraded cryostable superconducting solenoid, with NbTi at 4.2 K as the superconductor, then the smallest outer diameter is not achieved at the highest attainable field. There is a lower optimum field which minimizes the outer diameter for a given volt-second requirement. At higher fields the mean diameter decreases; but the high fields require more superconductor, more copper stabilizer, more stainless steel for support, and more liquid helium coolant. For the GA-ANL design for TNS, the optimum field is 7.55 T and the minimum outside diameter for the solenoid is 2.15 m. If, on the other hand, the solenoid is graded, with more NbTi, copper, and stainless steel on the inner turns where the field is higher, then the volt-seconds can always be increased, for a given outer diameter, by adding more turns at a higher field inside until either the critical field is reached or the solenoid bore is filled. However, the material and money required to add a few more volt-seconds increases rapidly with field

  14. Investigation of silicon sensors quality as a function of the ohmic side processing technology

    CERN Document Server

    Bloch, P; Golubkov, S A; Golutvin, I A; Egorov, N; Konjkov, K; Kozlov, Y; Peisert, Anna; Sidorov, A; Zamiatin, N I; Cheremuhin, A E

    2002-01-01

    Silicon sensors designed for the CMS Preshower detector must have a high breakdown voltage in order to be fully efficient after a strong irradiation. Studies made by several groups left bracket 1,2,3 right bracket have underlined the importance of the p**+ side geometrical parameters, such as the metal width and the number and spacing of guard rings. We have in addition investigated the effects related to the ohmic side processing and found that the breakdown voltage depends strongly on the depth of the effective "dead" n**+ layer. By increasing this thickness from mum to 2.5mum, the fraction of sensors with breakdown voltage higher than 500V increased from 22% to more than 80%. On the other hand, it was noticed that the starting surface quality of the wafer (double side polished or single side polished) does not affect the detectors parameters for a given production technology. The thick n**+-layer protects against initial wafer surface and defects caused by the technological treatment during the detector pr...

  15. Method of separate determination of high-ohmic sample resistance and contact resistance

    Directory of Open Access Journals (Sweden)

    Vadim A. Golubiatnikov

    2015-09-01

    Full Text Available A method of separate determination of two-pole sample volume resistance and contact resistance is suggested. The method is applicable to high-ohmic semiconductor samples: semi-insulating gallium arsenide, detector cadmium-zinc telluride (CZT, etc. The method is based on near-contact region illumination by monochromatic radiation of variable intensity from light emitting diodes with quantum energies exceeding the band gap of the material. It is necessary to obtain sample photo-current dependence upon light emitting diode current and to find the linear portion of this dependence. Extrapolation of this linear portion to the Y-axis gives the cut-off current. As the bias voltage is known, it is easy to calculate sample volume resistance. Then, using dark current value, one can determine the total contact resistance. The method was tested for n-type semi-insulating GaAs. The contact resistance value was shown to be approximately equal to the sample volume resistance. Thus, the influence of contacts must be taken into account when electrophysical data are analyzed.

  16. Global gyrokinetic simulations of intrinsic rotation in ASDEX Upgrade Ohmic L-mode plasmas

    Science.gov (United States)

    Hornsby, W. A.; Angioni, C.; Lu, Z. X.; Fable, E.; Erofeev, I.; McDermott, R.; Medvedeva, A.; Lebschy, A.; Peeters, A. G.; The ASDEX Upgrade Team

    2018-05-01

    Non-linear, radially global, turbulence simulations of ASDEX Upgrade (AUG) plasmas are performed and the nonlinear generated intrinsic flow shows agreement with the intrinsic flow gradients measured in the core of Ohmic L-mode plasmas at nominal parameters. Simulations utilising the kinetic electron model show hollow intrinsic flow profiles as seen in a predominant number of experiments performed at similar plasma parameters. In addition, significantly larger flow gradients are seen than in a previous flux-tube analysis (Hornsby et al 2017 Nucl. Fusion 57 046008). Adiabatic electron model simulations can show a flow profile with opposing sign in the gradient with respect to a kinetic electron simulation, implying a reversal in the sign of the residual stress due to kinetic electrons. The shaping of the intrinsic flow is strongly determined by the density gradient profile. The sensitivity of the residual stress to variations in density profile curvature is calculated and seen to be significantly stronger than to neoclassical flows (Hornsby et al 2017 Nucl. Fusion 57 046008). This variation is strong enough on its own to explain the large variations in the intrinsic flow gradients seen in some AUG experiments. Analysis of the symmetry breaking properties of the turbulence shows that profile shearing is the dominant mechanism in producing a finite parallel wave-number, with turbulence gradient effects contributing a smaller portion of the parallel wave-vector.

  17. Effect of the ohmic drop in a RPC-LIKE chamber for measurements of electron transport parameters

    Energy Technology Data Exchange (ETDEWEB)

    Petri, Anna R.; Gonçalves, Josemary A.C.; Bueno, Carmen C., E-mail: annapetri@usp.br, E-mail: josemary@ipen.br, E-mail: ccbueno@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil); Mangiarotti, Alessio, E-mail: alessio@if.usp.br [Universidade de São Paulo (IF/USP), SP (Brazil). Instituto de Física

    2017-07-01

    The main advantage of Resistive Plate Chambers (RPCs), applied, for instance, in High-Energy Experiments and Positron Emission Tomography (PET), is that it is spark-protected due to the presence of, at least, one high resistive electrode. However, the ohmic drop across the latter can affect the charge multiplication significantly. In this work, we investigate this effect in a RPC-like chamber. The counter was filled with nitrogen at atmospheric pressure and the primary ionization was produced by the incidence of nitrogen pulsed laser beam on an aluminum cathode. The illumination area of the cathode was measured using a foil of millimetric paper overlaid on this electrode. In this way, the resistance of the glass anode could be estimated using the known resistivity of the glass (ρ=2×10{sup 12} Ω.cm). Therefore, the voltage drop across the dielectric was calculated by the product of the current across the gas gap and the anode resistance. In order to mitigate the effect of the resistive electrode, the laser beam intensity was limited by interposing metallic meshes between the laser and the chamber window. The dependence of the ohmic drop from the applied voltage was analyzed. The results obtained shown that, without the meshes, the ohmic drop corresponds up to 7% of the applied voltage, preventing the detection system to reach values of density-normalized electric fields in the gas gap (E{sub eff}/N) higher than 166 Td. By minimizing the laser beam intensity and, consequently, the primary ionization, the ohmic drop represented only 0.2% of the applied voltage, extending the E{sub eff} /N range up to 175 Td. (author)

  18. Experimental study of the β-limit in ohmic H-mode in the TUMAN-3M tokamak

    International Nuclear Information System (INIS)

    Lebedev, S.V.; Andreiko, M.V.; Askinazi, L.G.; Golant, V.E.; Kornev, V.A.; Krikunov, S.V.; Levin, L.S.; Rozhdestvensky, V.V.; Tukachinsky, A.S.; Yaroshevich, S.P.

    1998-01-01

    Because of its high confinement properties, the H-mode provides good opportunities to achieve high beta values in a tokamak. In this paper the results of an experimental study of β T and β N limits in the H-mode, obtained in a circular cross section tokamak without auxiliary heating are presented. The experiments were performed in the TUMAN-3M tokamak. The device has the following parameters: R 0 =0.53m, a s =0.22m (limiter configuration), B T ≤1.2T, I p ≤175kA, n-bar e ≤6.2x10 19 m -3 . The stored energy was measured using diamagnetic loops and compared with W calculated from kinetic data obtained by Thomson scattering and microwave interferometry. Measurements of the stored energy and of the β were performed in the ohmic H-mode before and after boronization and in the scenario with fast current ramp-down in ohmic H-mode. A maximum value of β T of 2.0% and β N of 2.0 were achieved. The β N limit achieved reveals itself as a 'soft' (non-disruptive) limit. The stored energy slowly decays after the current ramp-down. No correlation was found between beta restriction and MHD phenomena. Internal transport barrier (ITB) formation was observed in ohmic H-mode. An enhancement factor of 2.0 over ITER93H(ELM-free) was found in the ohmic H-mode with ITB. (author)

  19. Modeling of the L.F. turbulent spectrum during ohmic discharges, auxiliary heating and disruptions in Tokamak

    International Nuclear Information System (INIS)

    Truc, A.

    1983-07-01

    The spectrum of low frequency turbulence in the TFR tokamak, as observed along a central chord by a CO 2 laser light diffusion diagnostic, appears to be representable by four monomial branches joining to three vertices. This schematic representation permits to follow more easily the evolution of the turbulence during the life of the plasma, including the ohmic regime, the transitions to auxiliary heating and the minor and major disruptions

  20. Intermittent fluctuations in the Alcator C-Mod scrape-off layer for ohmic and high confinement mode plasmas

    Science.gov (United States)

    Garcia, O. E.; Kube, R.; Theodorsen, A.; LaBombard, B.; Terry, J. L.

    2018-05-01

    Plasma fluctuations in the scrape-off layer of the Alcator C-Mod tokamak in ohmic and high confinement modes have been analyzed using gas puff imaging data. In all cases investigated, the time series of emission from a single spatially resolved view into the gas puff are dominated by large-amplitude bursts, attributed to blob-like filament structures moving radially outwards and poloidally. There is a remarkable similarity of the fluctuation statistics in ohmic plasmas and in edge localized mode-free and enhanced D-alpha high confinement mode plasmas. Conditionally averaged waveforms have a two-sided exponential shape with comparable temporal scales and asymmetry, while the burst amplitudes and the waiting times between them are exponentially distributed. The probability density functions and the frequency power spectral densities are similar for all these confinement modes. These results provide strong evidence in support of a stochastic model describing the plasma fluctuations in the scrape-off layer as a super-position of uncorrelated exponential pulses. Predictions of this model are in excellent agreement with experimental measurements in both ohmic and high confinement mode plasmas. The stochastic model thus provides a valuable tool for predicting fluctuation-induced plasma-wall interactions in magnetically confined fusion plasmas.

  1. Influence of infrared final cooking on polycyclic aromatic hydrocarbon formation in ohmically pre-cooked beef meatballs.

    Science.gov (United States)

    Kendirci, Perihan; Icier, Filiz; Kor, Gamze; Onogur, Tomris Altug

    2014-06-01

    Effects of infrared cooking on polycyclic aromatic hydrocarbon (PAH) formation in ohmically pre-cooked beef meatballs were investigated. Samples were pre-cooked in a specially designed-continuous type ohmic cooking at a voltage gradient of 15.26V/cm for 92s. Infrared cooking was applied as a final cooking method at different combinations of heat fluxes (3.706, 5.678, 8.475kW/m(2)), application distances (10.5, 13.5, 16.5cm) and application durations (4, 8, 12min). PAHs were analyzed by using high performance liquid chromatography (HPLC) equipped with a fluorescence detector. The total PAH levels were detected to be between 4.47 and 64μg/kg. Benzo[a] pyrene (B[a]P) and PAH4 (sum of B[a]P, chrysene (Chr), benzo[a]anthracene (B[a]A) and benzo[b]fluoranthene (B[b]F)) levels detected in meatballs were below the EC limits. Ohmic pre-cooking followed by infrared cooking may be regarded as a safe cooking procedure of meatballs from a PAH contamination point of view. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Ohmic contact formation process on low n-type gallium arsenide (GaAs) using indium gallium zinc oxide (IGZO)

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Seong-Uk [Samsung-SKKU Graphene Center and School of Electronics and Electrical Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Product and Test Engineering Team, System LSI Division, Samsung Electronics Co., Ltd, Yongin 446-711 (Korea, Republic of); Jung, Woo-Shik [Department of Electrical Engineering, Stanford University, Stanford, CA 94305 (United States); Lee, In-Yeal; Jung, Hyun-Wook; Kim, Gil-Ho [Samsung-SKKU Graphene Center and School of Electronics and Electrical Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Park, Jin-Hong, E-mail: jhpark9@skku.edu [Samsung-SKKU Graphene Center and School of Electronics and Electrical Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

    2014-02-01

    Highlights: • We propose a method to fabricate non-gold Ohmic contact on low n-type GaAs with IGZO. • 0.15 A/cm{sup 2} on-current and 1.5 on/off-current ratio are achieved in the junction. • InAs and InGaAs formed by this process decrease an electron barrier height. • Traps generated by diffused O atoms also induce a trap-assisted tunneling phenomenon. - Abstract: Here, an excellent non-gold Ohmic contact on low n-type GaAs is demonstrated by using indium gallium zinc oxide and investigating through time of flight-secondary ion mass spectrometry, X-ray photoelectron spectroscopy, transmission electron microscopy, J–V measurement, and H [enthalpy], S [entropy], Cp [heat capacity] chemistry simulation. In is diffused through GaAs during annealing and reacts with As, forming InAs and InGaAs phases with lower energy bandgap. As a result, it decreases the electron barrier height, eventually increasing the reverse current. In addition, traps generated by diffused O atoms induce a trap-assisted tunneling phenomenon, increasing generation current and subsequently the reverse current. Therefore, an excellent Ohmic contact with 0.15 A/cm{sup 2} on-current density and 1.5 on/off-current ratio is achieved on n-type GaAs.

  3. Formation Process and Properties of Ohmic Contacts Containing Molybdenum to AlGaN/GaN Heterostructures

    Directory of Open Access Journals (Sweden)

    Wojciech Macherzynski

    2016-01-01

    Full Text Available Properties of wide bandgap semiconductors as chemical inertness to harsh conditions and possibility of working at high temperature ensure possible applications in the field as military, aerospace, automotive, engine monitoring, flame detection and solar UV detection. Requirements for ohmic contacts in semiconductor devices are determined by the proposed application. These contacts to AlGaN/GaN heterostructure for application as high temperature, high frequency and high power devices have to exhibit good surface morphology and low contact resistance. The latter is a crucial factor in limiting the development of high performance AlGaN/GaN devices. Lowering of the resistance is assured by rapid thermal annealing process. The paper present studies of Ti/Al/Mo/Au ohmic contacst annealed at temperature range from 825°C to 885°C in N2 atmosphere. The electrical parameters of examined samples as a function of the annealing process condition have been studied. Initially the annealing temperature increase caused lowering of the contacts resistance. The lowest value was noticed for the temperature of annealing equal to 885°C. Further increase of annealing temperature led to deterioration of contact resistance of investigated ohmic contacts.

  4. Thermal stability of Ni/Ti/Al ohmic contacts to p-type 4H-SiC

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Hailong; Shen, Huajun, E-mail: shenhuajun@ime.ac.cn; Tang, Yidan; Bai, Yun; Liu, Xinyu [Microwave Device and IC Department, Institute of Microelectronics of Chinese Academy of Sciences, Beijing 100029 (China); Zhang, Xufang [School of Physical Science and Technology, Lanzhou University, Lanzhou 730000 (China); Wu, Yudong; Liu, Kean [Zhuzhou CSR Times Electric Co., Ltd, ZhuZhou 412001 (China)

    2015-01-14

    Low resistivity Ni/Ti/Al ohmic contacts on p-type 4H-SiC epilayer were developed, and their thermal stabilities were also experimentally investigated through high temperature storage at 600 °C for 100 h. The contact resistance of the Al/Ti/Ni/SiC contacts degraded in different degrees, and the contact morphology deteriorated with the increases of the average surface roughness and interface voids. X-ray spectra showed that Ni{sub 2}Si and Ti{sub 3}SiC{sub 2}, which were formed during ohmic contact annealing and contributed to low contact resistivity, were stable under high temperature storage. The existence of the TiAl{sub 3} and NiAl{sub 3} intermetallic phases was helpful to prevent Al agglomeration on the interface and make the contacts thermally stable. Auger electron spectroscopy indicated that the incorporation of oxygen at the surface and interface led to the oxidation of Al or Ti resulting in increased contact resistance. Also, the formation of these oxides roughened the surface and interface. The temperature-dependence of the specific contact resistance indicated that a thermionic field emission mechanism dominates the current transport for contacts before and after the thermal treatment. It suggests that the Ni/Ti/Al composite ohmic contacts are promising for SiC devices to be used in high temperature applications.

  5. Disorder-induced enhancement of conductance in doped nanowires

    Institute of Scientific and Technical Information of China (English)

    Xu Ning; Wang Bao-Lin; Sun Hou-Qian; Kong Fan-Jie

    2010-01-01

    A new mechanism is proposed to explain the enhancement of conductance in doped nanowires. It is shown that the anomalous enhancement of conductance is due to surface doping. The conductance in doped nanowires increases with dopant concentration, which is qualitatively consistent with the existing experimental results. In addition, the I-V curves are linear and thus suggest that the metal electrodes make ohmic contacts to the shell-doped nanowires.The electric current increases with wire diameter (D) and decreases exponentially with wire length (L). Therefore, the doped nanowires have potential application in nanoscale electronic and optoelectronic devices.

  6. Electrical characterization and nanoscale surface morphology of optimized Ti/Al/Ta/Au ohmic contact for AlGaN/GaN HEMT.

    Science.gov (United States)

    Wang, Cong; Kim, Nam-Young

    2012-02-07

    Good ohmic contacts with low contact resistance, smooth surface morphology, and a well-defined edge profile are essential to ensure optimal device performances for the AlGaN/GaN high electron mobility transistors [HEMTs]. A tantalum [Ta] metal layer and an SiNx thin film were used for the first time as an effective diffusion barrier and encapsulation layer in the standard Ti/Al/metal/Au ohmic metallization scheme in order to obtain high quality ohmic contacts with a focus on the thickness of Ta and SiNx. It is found that the Ta thickness is the dominant factor affecting the contact resistance, while the SiNx thickness affects the surface morphology significantly. An optimized Ti/Al/Ta/Au ohmic contact including a 40-nm thick Ta barrier layer and a 50-nm thick SiNx encapsulation layer is preferred when compared with the other conventional ohmic contact stacks as it produces a low contact resistance of around 7.27 × 10-7 Ω·cm2 and an ultra-low nanoscale surface morphology with a root mean square deviation of around 10 nm. Results from the proposed study play an important role in obtaining excellent ohmic contact formation in the fabrication of AlGaN/GaN HEMTs.

  7. Optimized design of polarizers with low ohmic loss and any polarization state for the 28 GHz QUEST ECH/ECCD system

    Energy Technology Data Exchange (ETDEWEB)

    Tsujimura, Toru Ii, E-mail: tsujimura.tohru@nifs.ac.jp [National Institute for Fusion Science, National Institutes of Natural Sciences, Toki 509-5292 (Japan); Idei, Hiroshi [Research Institute for Applied Mechanics, Kyushu University, Kasuga 816-8580 (Japan); Kubo, Shin; Kobayashi, Sakuji [National Institute for Fusion Science, National Institutes of Natural Sciences, Toki 509-5292 (Japan)

    2017-01-15

    Highlights: • Ohmic loss was calculated on the grooved mirror surface in simulated polarizers. • Polarizers with a low ohmic loss feature were optimally designed for 28 GHz. • Smooth rounded-rectangular grooves were made by mechanical machining. • The designed polarizers can realize all polarization states. - Abstract: In a high-power long-pulse millimeter-wave transmission line for electron cyclotron heating and current drive (ECH/ECCD), the ohmic loss on the grooved mirror surface of polarizers is one of the important issues for reducing the transmission loss. In this paper, the ohmic loss on the mirror surface is evaluated in simulated real-scale polarizer miter bends for different groove parameters under a linearly-polarized incident wave excitation. The polarizers with low ohmic loss are optimally designed for a new 28 GHz transmission line on the QUEST spherical tokamak. The calculated optimum ohmic loss is restricted to only less than 1.5 times as large as the theoretical loss for a copper flat mirror at room temperature. The copper rounded-rectangular grooves of the polarizers were relatively easy to make smooth in mechanical machining and the resultant surface roughness was not more than 0.15 μm, which is only 0.38 times as large as the skin depth. The combination of the designed elliptical polarizer and the polarization rotator can also realize any polarization state of the reflected wave.

  8. Association of Endothelial Nitric Oxide Synthase Gene Polymorphisms With Acute Rejection in Liver Transplant Recipients.

    Science.gov (United States)

    Azarpira, Negar; Namazi, Soha; Malahi, Sayan; Kazemi, Kourosh

    2016-06-01

    Polymorphisms of the endothelial nitric oxide synthase gene have been associated with altered endothelial nitric oxide synthase activity. The purpose of this study was to investigate the relation between endothelial nitric oxide synthase -786T/C and 894G/T polymorphism and their haplotypes on the occurrence of acute rejection episodes in liver transplant recipients. We conducted a case control study in which 100 liver transplant recipients and 100 healthy controls were recruited from Shiraz Transplant Center. The patients used triple therapy including tacrolimus, mycophenolate mofetil, and prednisolone for immunosuppression maintenance. DNA was extracted from peripheral blood and endothelial nitric oxide synthase polymorphisms were determined by polymerase chain reaction and restriction fragment length polymorphism. Patients included 60 men and 40 women (mean age, 32.35 ± 10.2 y). There was a significant association of endothelial nitric oxide synthase 894G/T and acute rejection episode. The GT* gen-otype and acute rejection episodes had a significant association (odds ratio, 2.42; 95% confidence interval, 0.97-6.15; P = .03). The GG and GT* genotype and T* allele frequency were significantly different between patients and control subjects (P = .001). Haplotype TT* was higher in recipients than control subjects (odds ratio, 2.17; 95% confidence interval, 1.12-4.25; P = .01). Haplotype TG was higher in the control group (odds ratio, 0.62; 95% confidence interval, 0.40-0.96; P = .02). Our results suggest a relation between different endothelial nitric oxide synthase geno-types and risk of acute rejection episodes. However, further study is necessary to determine genetic susceptibility for transplant patients.

  9. From Schottky to Ohmic graphene contacts to AlGaN/GaN heterostructures: Role of the AlGaN layer microstructure

    International Nuclear Information System (INIS)

    Fisichella, G.; Greco, G.; Roccaforte, F.; Giannazzo, F.

    2014-01-01

    The electrical behaviour of graphene (Gr) contacts to Al x Ga 1−x N/GaN heterostructures has been investigated, focusing, in particular, on the impact of the AlGaN microstructure on the current transport at Gr/AlGaN interface. Two Al 0.25 Ga 0.75 N/GaN heterostructures with very different quality in terms of surface roughness and defectivity, as evaluated by atomic force microscopy (AFM) and transmission electron microscopy, were compared in this study, i.e., a uniform and defect-free sample and a sample with a high density of typical V-defects, which locally cause a reduction of the AlGaN thickness. Nanoscale resolution current voltage (I-V) measurements by an Au coated conductive AFM tip were carried out at several positions both on the bare and Gr-coated AlGaN surfaces. Rectifying contacts were found onto both bare AlGaN surfaces, but with a more inhomogeneous and lower Schottky barrier height (Φ B  ≈ 0.6 eV) for AlGaN with V-defects, with respect to the case of the uniform AlGaN (Φ B  ≈ 0.9 eV). Instead, very different electrical behaviours were observed in the presence of the Gr interlayer between the Au tip and AlGaN, i.e., a Schottky contact with reduced barrier height (Φ B ≈ 0.4 eV) for the uniform AlGaN and an Ohmic contact for the AlGaN with V-defects. Interestingly, excellent lateral uniformity of the local I-V characteristics was found in both cases and can be ascribed to an averaging effect of the Gr electrode over the AlGaN interfacial inhomogeneities. Due to the locally reduced AlGaN layer thickness, V defect act as preferential current paths from Gr to the 2DEG and can account for the peculiar Ohmic behaviour of Gr contacts on defective AlGaN

  10. Analysis and testing of the DIII-D ohmic heating coil lead repair clamp

    International Nuclear Information System (INIS)

    Reis, E.E.; Anderson, P.M.; Chin, E.; Robinson, J.I.

    1997-11-01

    DIII-D has been operating for the last year with limited volt-second capabilities due to structural failure of a conductor lead to one of the ohmic heating (OH) solenoids. The conductor failure was due to poor epoxy impregnation of the overwrap of the lead pack, resulting in copper fatigue and a water leak. A number of structural analyses were performed to assist in determining the failure scenario and to evaluate various repair options. A fatigue stress analysis of the leads with a failed epoxy overwrap indicated crack initiation after 1,000 cycles at the maximum operating conditions. The failure occurred in a very inaccessible area which restricted design repair options to concepts which could be implemented remotely. Several design options were considered for repairing the lead so that it can sustain the loads for 7.5 Vs conditions at full toroidal field. A clamp, along with preloaded banding straps and shim bags, provides a system that guarantees that the stress at the crack location is always compressive and prevents further crack growth in the conductor. Due to the limited space available for the repair, it was necessary to design the clamp system to operate at the material yield stress. The primary components of the clamp system were verified by load tests prior to installation. The main body of the clamp contains a load cell and potentiometer for monitoring the load-deflection characteristics of the clamp and conductors during plasma operation. Strain gages provides redundant instrumentation. If required, the preload on the conductors can be increased remotely by a special wrench attached to the clamp assembly

  11. Plasma rotation and radial electric field with a density ramp in an ohmically heated tokamak

    International Nuclear Information System (INIS)

    Duval, B.P.; Joye, B.; Marchal, B.

    1991-10-01

    Measurements of toroidal and poloidal rotation of the TCA plasma with Alfven Wave Heating and different levels of gas feed are reported. The temporal evolution of the rotation was inferred from intrinsic spectral lines of CV, CIII and, using injected helium gas, from HeII. The light collection optics and line intensity permitted the evolution of the plasma rotation to be measured with a time resolution of 2ms. The rotation velocities were used to deduce the radial electric field. With Alfven heating there was no observable change of this electric field that could have been responsible for the density rise which is characteristic of the RF experiments on TCA. The behaviour of the plasma rotation with different plasma density ramp rates was investigated. The toroidal rotation was observed to decrease with increasing plasma density. The poloidal rotation was observed to follow the value of the plasma density. With hard gas puffing, changes in the deduced radial electric field were found to coincide with changes in the peaking of the plasma density profile. Finally, with frozen pellet injection, the expected increase in the radial electric field due to the increased plasma density was not observed, which may explain the poorer confinement of the injected particles. Even in an ohmically heated tokamak, the measurement of the plasma rotation and the radial electric field are shown to be strongly related to the confinement. A thorough statistical analysis of the systematic errors is presented and a new and significant source of uncertainty in the experimental technique is identified. (author) 18 figs., 18 refs

  12. CTP synthase forms cytoophidia in the cytoplasm and nucleus

    International Nuclear Information System (INIS)

    Gou, Ke-Mian; Chang, Chia-Chun; Shen, Qing-Ji; Sung, Li-Ying; Liu, Ji-Long

    2014-01-01

    CTP synthase is an essential metabolic enzyme responsible for the de novo synthesis of CTP. Multiple studies have recently showed that CTP synthase protein molecules form filamentous structures termed cytoophidia or CTP synthase filaments in the cytoplasm of eukaryotic cells, as well as in bacteria. Here we report that CTP synthase can form cytoophidia not only in the cytoplasm, but also in the nucleus of eukaryotic cells. Both glutamine deprivation and glutamine analog treatment promote formation of cytoplasmic cytoophidia (C-cytoophidia) and nuclear cytoophidia (N-cytoophidia). N-cytoophidia are generally shorter and thinner than their cytoplasmic counterparts. In mammalian cells, both CTP synthase 1 and CTP synthase 2 can form cytoophidia. Using live imaging, we have observed that both C-cytoophidia and N-cytoophidia undergo multiple rounds of fusion upon glutamine analog treatment. Our study reveals the coexistence of cytoophidia in the cytoplasm and nucleus, therefore providing a good opportunity to investigate the intracellular compartmentation of CTP synthase. - Highlights: • CTP synthase forms cytoophidia not only in the cytoplasm but also in the nucleus. • Glutamine deprivation and Glutamine analogs promotes cytoophidium formation. • N-cytoophidia exhibit distinct morphology when compared to C-cytoophidia. • Both CTP synthase 1 and CTP synthase 2 form cytoophidia in mammalian cells. • Fusions of cytoophidia occur in the cytoplasm and nucleus

  13. CTP synthase forms cytoophidia in the cytoplasm and nucleus

    Energy Technology Data Exchange (ETDEWEB)

    Gou, Ke-Mian [MRC Functional Genomics Unit, Department of Physiology, Anatomy and Genetics, University of Oxford, Oxford OX1 3PT (United Kingdom); State Key Laboratory for Agrobiotechnology, College of Biological Sciences, China Agricultural University, Beijing 100193 (China); Chang, Chia-Chun [Institute of Biotechnology, National Taiwan University, Taipei, Taiwan, ROC (China); Shen, Qing-Ji [MRC Functional Genomics Unit, Department of Physiology, Anatomy and Genetics, University of Oxford, Oxford OX1 3PT (United Kingdom); Sung, Li-Ying, E-mail: liyingsung@ntu.edu.tw [Institute of Biotechnology, National Taiwan University, Taipei, Taiwan, ROC (China); Agricultural Biotechnology Research Center, Academia Sinica, Taipei 115, Taiwan, ROC (China); Liu, Ji-Long, E-mail: jilong.liu@dpag.ox.ac.uk [MRC Functional Genomics Unit, Department of Physiology, Anatomy and Genetics, University of Oxford, Oxford OX1 3PT (United Kingdom)

    2014-04-15

    CTP synthase is an essential metabolic enzyme responsible for the de novo synthesis of CTP. Multiple studies have recently showed that CTP synthase protein molecules form filamentous structures termed cytoophidia or CTP synthase filaments in the cytoplasm of eukaryotic cells, as well as in bacteria. Here we report that CTP synthase can form cytoophidia not only in the cytoplasm, but also in the nucleus of eukaryotic cells. Both glutamine deprivation and glutamine analog treatment promote formation of cytoplasmic cytoophidia (C-cytoophidia) and nuclear cytoophidia (N-cytoophidia). N-cytoophidia are generally shorter and thinner than their cytoplasmic counterparts. In mammalian cells, both CTP synthase 1 and CTP synthase 2 can form cytoophidia. Using live imaging, we have observed that both C-cytoophidia and N-cytoophidia undergo multiple rounds of fusion upon glutamine analog treatment. Our study reveals the coexistence of cytoophidia in the cytoplasm and nucleus, therefore providing a good opportunity to investigate the intracellular compartmentation of CTP synthase. - Highlights: • CTP synthase forms cytoophidia not only in the cytoplasm but also in the nucleus. • Glutamine deprivation and Glutamine analogs promotes cytoophidium formation. • N-cytoophidia exhibit distinct morphology when compared to C-cytoophidia. • Both CTP synthase 1 and CTP synthase 2 form cytoophidia in mammalian cells. • Fusions of cytoophidia occur in the cytoplasm and nucleus.

  14. The role of high work-function metallic nanodots on the performance of a-Si:H solar cells: offering ohmic contact to light trapping.

    Science.gov (United States)

    Kim, Jeehwan; Abou-Kandil, Ahmed; Fogel, Keith; Hovel, Harold; Sadana, Devendra K

    2010-12-28

    Addition of carbon into p-type "window" layers in hydrogenated amorphous silicon (a-Si:H) solar cells enhances short circuit currents and open circuit voltages by a great deal. However, a-Si:H solar cells with high carbon-doped "window" layers exhibit poor fill factors due to a Schottky barrier-like impedance at the interface between a-SiC:H windows and transparent conducting oxides (TCO), although they show maximized short circuit currents and open circuit voltages. The impedance is caused by an increasing mismatch between the work function of TCO and that of p-type a-SiC:H. Applying ultrathin high-work-function metals at the interface between the two materials results in an effective lowering of the work function mismatch and a consequent ohmic behavior. If the metal layer is sufficiently thin, then it forms nanodots rather than a continuous layer which provides light-scattering effect. We demonstrate 31% efficiency enhancement by using high-work-function materials for engineering the work function at the key interfaces to raise fill factors as well as photocurrents. The use of metallic interface layers in this work is a clear contrast to previous work where attempts were made to enhance the photocurrent using plasmonic metal nanodots on the solar cell surface.

  15. Improvement of Ohmic contacts on Ga2O3 through use of ITO-interlayers

    Energy Technology Data Exchange (ETDEWEB)

    Carey, Patrick H. [Univ. of Florida, Gainesville, FL (United States). Department of Chemical Engineering; Yang, Jiancheng [Univ. of Florida, Gainesville, FL (United States). Department of Chemical Engineering; Ren, Fan [Univ. of Florida, Gainesville, FL (United States). Department of Chemical Engineering; Hays, David C. [Univ. of Florida, Gainesville, FL (United States). Department of Materials Science and Engineering; Pearton, Stephen J. [Univ. of Florida, Gainesville, FL (United States). Department of Materials Science and Engineering; Kuramata, Akito [Tamura Corporation, Sayama (Japan). Japan and Novel Crystal Technology, Inc.; Kravchenko, Ivan I. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Center for Nanophase Materials Science (CNMS)

    2017-10-03

    In this work, the use of ITO interlayers between Ga2O3 and Ti/Au metallization is shown to produce Ohmic contacts after annealing in the range of 500–600 °C. Without the ITO, similar anneals do not lead to linear current–voltage characteristics. Transmission line measurements were used to extract the specific contact resistance of the Au/Ti/ITO/Ga2O3 stacks as a function of annealing temperature. Sheet, specific contact, and transfer resistances all decreased sharply from as-deposited values with annealing. The minimum transfer resistance and specific contact resistance of 0.60 Ω mm and 6.3 × 10-5 Ω cm2 were achieved after 600 °C annealing, respectively. Lastly, the conduction band offset between ITO and Ga2O3 is 0.32 eV and is consistent with the improved electron transport across the heterointerface.

  16. Lead-germanium ohmic contact on to gallium arsenide formed by the solid phase epitaxy of germanium: A microstructure study

    Science.gov (United States)

    Radulescu, Fabian

    2000-12-01

    Driven by the remarkable growth in the telecommunication market, the demand for more complex GaAs circuitry continued to increase in the last decade. As a result, the GaAs industry is faced with new challenges in its efforts to fabricate devices with smaller dimensions that would permit higher integration levels. One of the limiting factors is the ohmic contact metallurgy of the metal semiconductor field effect transistor (MESFET), which, during annealing, induces a high degree of lateral diffusion into the substrate. Because of its limited reaction with the substrate, the Pd-Ge contact seems to be the most promising candidate to be used in the next generation of MESFET's. The Pd-Ge system belongs to a new class of ohmic contacts to compound semiconductors, part of an alloying strategy developed only recently, which relies on solid phase epitaxy (SPE) and solid phase regrowth to "un-pin" the Fermi level at the surface of the compound semiconductor. However, implementing this alloy into an integrated process flow proved to be difficult due to our incomplete understanding of the microstructure evolution during annealing and its implications on the electrical properties of the contact. The microstructure evolution and the corresponding solid state reactions that take place during annealing of the Pd-Ge thin films on to GaAs were studied in connection with their effects on the electrical properties of the ohmic contact. The phase transformations sequence, transition temperatures and activation energies were determined by combining differential scanning calorimetry (DSC) for thermal analysis with transmission electron microscopy (TEM) for microstructure identification. In-situ TEM annealing experiments on the Pd/Ge/Pd/GaAs ohmic contact system have permitted real time determination of the evolution of contact microstructure. The kinetics of the solid state reactions, which occur during ohmic contact formation, were determined by measuring the grain growth rates

  17. Conducting Polymers

    Indian Academy of Sciences (India)

    would exhibit electronic conductivity, their conductivities (of compressed pellets) were indeed measured by others, and were found to be .... Polyaniline. Polyphenylene. Polypheny lene- vinylene. Table 1. G!NeRAl I ARTICl! structure. Maximum conductivity Stem Stability. Processability. ~. 1.5 x 105. Reacts with Film not n air.

  18. Clinical significance of Phosphatidyl Inositol Synthase overexpression in oral cancer

    International Nuclear Information System (INIS)

    Kaur, Jatinder; Sawhney, Meenakshi; DattaGupta, Siddartha; Shukla, Nootan K; Srivastava, Anurag; Ralhan, Ranju

    2010-01-01

    We reported increased levels of Phosphatidyl Inositol synthase (PI synthase), (enzyme that catalyses phosphatidyl inositol (PI) synthesis-implicated in intracellular signaling and regulation of cell growth) in smokeless tobacco (ST) exposed oral cell cultures by differential display. This study determined the clinical significance of PI synthase overexpression in oral squamous cell carcinoma (OSCC) and premalignant lesions (leukoplakia), and identified the downstream signaling proteins in PI synthase pathway that are perturbed by smokeless tobacco (ST) exposure. Tissue microarray (TMA) Immunohistochemistry, Western blotting, Confocal laser scan microscopy, RT-PCR were performed to define the expression of PI synthase in clinical samples and in oral cell culture systems. Significant increase in PI synthase immunoreactivity was observed in premalignant lesions and OSCCs as compared to oral normal tissues (p = 0.000). Further, PI synthase expression was significantly associated with de-differentiation of OSCCs, (p = 0.005) and tobacco consumption (p = 0.03, OR = 9.0). Exposure of oral cell systems to smokeless tobacco (ST) in vitro confirmed increase in PI synthase, Phosphatidylinositol 3-kinase (PI3K) and cyclin D1 levels. Collectively, increased PI synthase expression was found to be an early event in oral cancer and a target for smokeless tobacco

  19. Synergetic aspects of gas-discharge: lateral patterns in dc systems with a high ohmic barrier

    Science.gov (United States)

    Purwins, H.-G.; Stollenwerk, L.

    2014-12-01

    The understanding of self-organized patterns in spatially extended nonlinear dissipative systems is one of the most challenging subjects in modern natural sciences. Such patterns are also referred to as dissipative structures. We review this phenomenon in planar low temperature dc gas-discharge devices with a high ohmic barrier. It is demonstrated that for these systems a deep qualitative understanding of dissipative structures can be obtained from the point of view of synergetics. At the same time, a major contribution can be made to the general understanding of dissipative structures. The discharge spaces of the experimentally investigated systems, to good approximation, have translational and rotational symmetry by contraction. Nevertheless, a given system may exhibit stable current density distributions and related patterns that break these symmetries. Among the experimentally observed fundamental patterns one finds homogeneous isotropic states, fronts, periodic patterns, labyrinth structures, rotating spirals, target patterns and localized filaments. In addition, structures are observed that have the former as elementary building blocks. Finally, defect structures as well as irregular patterns are common phenomena. Such structures have been detected in numerous other driven nonlinear dissipative systems, as there are ac gas-discharge devices, semiconductors, chemical solutions, electrical networks and biological systems. Therefore, from the experimental observations it is concluded that the patterns in planar low temperature dc gas-discharge devices exhibit universal behavior. From the theoretical point of view, dissipative structures of the aforementioned kind are also referred to as attractors. The possible sets of attractors are an important characteristic of the system. The number and/or qualitative nature of attractors may change when changing parameters. The related bifurcation behavior is a central issue of the synergetic approach chosen in the present

  20. Synergetic aspects of gas-discharge: lateral patterns in dc systems with a high ohmic barrier

    International Nuclear Information System (INIS)

    Purwins, H-G; Stollenwerk, L

    2014-01-01

    The understanding of self-organized patterns in spatially extended nonlinear dissipative systems is one of the most challenging subjects in modern natural sciences. Such patterns are also referred to as dissipative structures. We review this phenomenon in planar low temperature dc gas-discharge devices with a high ohmic barrier. It is demonstrated that for these systems a deep qualitative understanding of dissipative structures can be obtained from the point of view of synergetics. At the same time, a major contribution can be made to the general understanding of dissipative structures. The discharge spaces of the experimentally investigated systems, to good approximation, have translational and rotational symmetry by contraction. Nevertheless, a given system may exhibit stable current density distributions and related patterns that break these symmetries. Among the experimentally observed fundamental patterns one finds homogeneous isotropic states, fronts, periodic patterns, labyrinth structures, rotating spirals, target patterns and localized filaments. In addition, structures are observed that have the former as elementary building blocks. Finally, defect structures as well as irregular patterns are common phenomena. Such structures have been detected in numerous other driven nonlinear dissipative systems, as there are ac gas-discharge devices, semiconductors, chemical solutions, electrical networks and biological systems. Therefore, from the experimental observations it is concluded that the patterns in planar low temperature dc gas-discharge devices exhibit universal behavior. From the theoretical point of view, dissipative structures of the aforementioned kind are also referred to as attractors. The possible sets of attractors are an important characteristic of the system. The number and/or qualitative nature of attractors may change when changing parameters. The related bifurcation behavior is a central issue of the synergetic approach chosen in the present

  1. Transport mechanisms in low-resistance ohmic contacts to p-InP formed by rapid thermal annealing

    DEFF Research Database (Denmark)

    Clausen, Thomas; Leistiko, Otto

    1993-01-01

    process is related to interdiffusion and compound formation between the metal elements and the InP. The onset of low specific contact resistance is characterized by a change in the dominant transport mechanism; from predominantly a combination of thermionic emission and field emission to purely thermionic......Thermionic emission across a very small effective Schottky barrier (0-0.2 eV) are reported as being the dominant transport process mechanism in very low-resistance ohmic contacts for conventional AuZn(Ni) metallization systems top-InP formed by rapid thermal annealing. The barrier modulation...

  2. III-V/Si wafer bonding using transparent, conductive oxide interlayers

    Energy Technology Data Exchange (ETDEWEB)

    Tamboli, Adele C., E-mail: Adele.Tamboli@nrel.gov; Hest, Maikel F. A. M. van; Steiner, Myles A.; Essig, Stephanie; Norman, Andrew G.; Bosco, Nick; Stradins, Paul [National Center for Photovoltaics, National Renewable Energy Laboratory, 15013 Denver West Pkwy, Golden, Colorado 80401 (United States); Perl, Emmett E. [Department of Electrical and Computer Engineering, University of California, Santa Barbara, California 93106-9560 (United States)

    2015-06-29

    We present a method for low temperature plasma-activated direct wafer bonding of III-V materials to Si using a transparent, conductive indium zinc oxide interlayer. The transparent, conductive oxide (TCO) layer provides excellent optical transmission as well as electrical conduction, suggesting suitability for Si/III-V hybrid devices including Si-based tandem solar cells. For bonding temperatures ranging from 100 °C to 350 °C, Ohmic behavior is observed in the sample stacks, with specific contact resistivity below 1 Ω cm{sup 2} for samples bonded at 200 °C. Optical absorption measurements show minimal parasitic light absorption, which is limited by the III-V interlayers necessary for Ohmic contact formation to TCOs. These results are promising for Ga{sub 0.5}In{sub 0.5}P/Si tandem solar cells operating at 1 sun or low concentration conditions.

  3. Neuronal nitric oxide synthase-deficient mice have impaired Renin release but normal blood pressure

    DEFF Research Database (Denmark)

    Sällström, Johan; Carlström, Mattias; Jensen, Boye L

    2008-01-01

    BackgroundNitric oxide deficiency is involved in the development of hypertension, but the mechanisms are currently unclear. This study was conducted to further elucidate the role of neuronal nitric oxide synthase (nNOS) in blood pressure regulation and renin release in relation to different sodiu......-116; doi:10.1038/ajh.2007.16American Journal of Hypertension (2008) 21 111-116; doi:10.1038/ajh.2007.16....

  4. Genomic Analysis of Terpene Synthase Family and Functional Characterization of Seven Sesquiterpene Synthases from Citrus sinensis

    Directory of Open Access Journals (Sweden)

    Berta Alquézar

    2017-08-01

    Full Text Available Citrus aroma and flavor, chief traits of fruit quality, are derived from their high content in essential oils of most plant tissues, including leaves, stems, flowers, and fruits. Accumulated in secretory cavities, most components of these oils are volatile terpenes. They contribute to defense against herbivores and pathogens, and perhaps also protect tissues against abiotic stress. In spite of their importance, our understanding of the physiological, biochemical, and genetic regulation of citrus terpene volatiles is still limited. The availability of the sweet orange (Citrus sinensis L. Osbeck genome sequence allowed us to characterize for the first time the terpene synthase (TPS family in a citrus type. CsTPS is one of the largest angiosperm TPS families characterized so far, formed by 95 loci from which just 55 encode for putative functional TPSs. All TPS angiosperm families, TPS-a, TPS-b, TPS-c, TPS-e/f, and TPS-g were represented in the sweet orange genome, with 28, 18, 2, 2, and 5 putative full length genes each. Additionally, sweet orange β-farnesene synthase, (Z-β-cubebene/α-copaene synthase, two β-caryophyllene synthases, and three multiproduct enzymes yielding β-cadinene/α-copaene, β-elemene, and β-cadinene/ledene/allo-aromandendrene as major products were identified, and functionally characterized via in vivo recombinant Escherichia coli assays.

  5. Chrysanthemyl diphosphate synthase operates in planta as a bifunctional enzyme with chrysanthemol synthase activity

    DEFF Research Database (Denmark)

    Yang, Ting; Gao, Liping; Hu, Hao

    2014-01-01

    Chrysanthemyl diphosphate synthase (CDS) is the first path-way-specific enzyme in the biosynthesis of pyrethrins, the most widely used plant-derived pesticide. CDS catalyzes c1′-2-3 cyclopropanation reactions of two molecules of dimethylallyl diphosphate (DMAPP) to yield chrysanthemyl diphosphate...

  6. Bias induced transition from an ohmic to a non-ohmic interface in supramolecular tunneling junctions with Ga2O3/EGaIn top electrodes

    NARCIS (Netherlands)

    Wimbush, K.S.; Fratila, R.M.; Wang, D.D.; Qi, D.C.; Liang, C.; Yuan, L.; Yakovlev, N.; Loh, K.P.; Reinhoudt, D.N.; Velders, A.H.; Nijhuis, C.A.

    2014-01-01

    This study describes that the current rectification ratio, R h equivalent to vertical bar J vertical bar(+2.0 V)/vertical bar J vertical bar(+2.0 V) for supramolecular tunneling junctions with a top-electrode of eutectic gallium indium (EGaIn) that contains a conductive thin (0.7 nm) supporting

  7. Analysis of Electron Thermal Diffusivity and Bootstrap Current in Ohmically Heated Discharges after Boronization in the HT-7 Tokamak

    International Nuclear Information System (INIS)

    Zhang, X.M.; Wan, B.N.

    2005-01-01

    Significant improvements of plasma performance after ICRF boronization have been achieved in the full range of HT-7 operation parameters. Electron power balance is analyzed in the steady state ohmic discharges of the HT-7 tokamak. The ratio of the total radiation power to ohmic input power increases with increasing the central line-averaged electron density, but decreases with plasma current. It is obviously decreased after wall conditioning. Electron heat diffusivity χ e deduced from the power balance analysis is reduced throughout the main plasma after boronization. χ e decreases with increasing central line-averaged electron density in the parameter range of our study. After boronization, the plasma current profile is broadened and a higher current can be easily obtained on the HT-7 tokamak experiment. It is expected that the fact that the bootstrap current increases after boronization will explain these phenomena. After boronization, the plasma pressure gradient and the electron temperature near the boundary are larger than before, these factors influencing that the ratio of bootstrap current to total plasma current increases from several percent to above 10%

  8. Lack of dependence on resonant error field of locked mode island size in ohmic plasmas in DIII-D

    Science.gov (United States)

    La Haye, R. J.; Paz-Soldan, C.; Strait, E. J.

    2015-02-01

    DIII-D experiments show that fully penetrated resonant n = 1 error field locked modes in ohmic plasmas with safety factor q95 ≳ 3 grow to similar large disruptive size, independent of resonant error field correction. Relatively small resonant (m/n = 2/1) static error fields are shielded in ohmic plasmas by the natural rotation at the electron diamagnetic drift frequency. However, the drag from error fields can lower rotation such that a bifurcation results, from nearly complete shielding to full penetration, i.e., to a driven locked mode island that can induce disruption. Error field correction (EFC) is performed on DIII-D (in ITER relevant shape and safety factor q95 ≳ 3) with either the n = 1 C-coil (no handedness) or the n = 1 I-coil (with ‘dominantly’ resonant field pitch). Despite EFC, which allows significantly lower plasma density (a ‘figure of merit’) before penetration occurs, the resulting saturated islands have similar large size; they differ only in the phase of the locked mode after typically being pulled (by up to 30° toroidally) in the electron diamagnetic drift direction as they grow to saturation. Island amplification and phase shift are explained by a second change-of-state in which the classical tearing index changes from stable to marginal by the presence of the island, which changes the current density profile. The eventual island size is thus governed by the inherent stability and saturation mechanism rather than the driving error field.

  9. Changes in core electron temperature fluctuations across the ohmic energy confinement transition in Alcator C-Mod plasmas

    International Nuclear Information System (INIS)

    Sung, C.; White, A.E.; Howard, N.T.; Oi, C.Y.; Rice, J.E.; Gao, C.; Ennever, P.; Porkolab, M.; Parra, F.; Ernst, D.; Walk, J.; Hughes, J.W.; Irby, J.; Kasten, C.; Hubbard, A.E.; Greenwald, M.J.; Mikkelsen, D.

    2013-01-01

    The first measurements of long wavelength (k y ρ s < 0.3) electron temperature fluctuations in Alcator C-Mod made with a new correlation electron cyclotron emission diagnostic support a long-standing hypothesis regarding the confinement transition from linear ohmic confinement (LOC) to saturated ohmic confinement (SOC). Electron temperature fluctuations decrease significantly (∼40%) crossing from LOC to SOC, consistent with a change from trapped electron mode (TEM) turbulence domination to ion temperature gradient (ITG) turbulence as the density is increased. Linear stability analysis performed with the GYRO code (Candy and Waltz 2003 J. Comput. Phys. 186 545) shows that TEMs are dominant for long wavelength turbulence in the LOC regime and ITG modes are dominant in the SOC regime at the radial location (ρ ∼ 0.8) where the changes in electron temperature fluctuations are measured. In contrast, deeper in the core (ρ < 0.8), linear stability analysis indicates that ITG modes remain dominant across the LOC/SOC transition. This radial variation suggests that the robust global changes in confinement of energy and momentum occurring across the LOC/SOC transition are correlated to local changes in the dominant turbulent mode near the edge. (paper)

  10. Density scaling on n  =  1 error field penetration in ohmically heated discharges in EAST

    Science.gov (United States)

    Wang, Hui-Hui; Sun, You-Wen; Shi, Tong-Hui; Zang, Qing; Liu, Yue-Qiang; Yang, Xu; Gu, Shuai; He, Kai-Yang; Gu, Xiang; Qian, Jin-Ping; Shen, Biao; Luo, Zheng-Ping; Chu, Nan; Jia, Man-Ni; Sheng, Zhi-Cai; Liu, Hai-Qing; Gong, Xian-Zu; Wan, Bao-Nian; Contributors, EAST

    2018-05-01

    Density scaling of error field penetration in EAST is investigated with different n  =  1 magnetic perturbation coil configurations in ohmically heated discharges. The density scalings of error field penetration thresholds under two magnetic perturbation spectra are br\\propto n_e0.5 and br\\propto n_e0.6 , where b r is the error field and n e is the line averaged electron density. One difficulty in understanding the density scaling is that key parameters other than density in determining the field penetration process may also be changed when the plasma density changes. Therefore, they should be determined from experiments. The estimated theoretical analysis (br\\propto n_e0.54 in lower density region and br\\propto n_e0.40 in higher density region), using the density dependence of viscosity diffusion time, electron temperature and mode frequency measured from the experiments, is consistent with the observed scaling. One of the key points to reproduce the observed scaling in EAST is that the viscosity diffusion time estimated from energy confinement time is almost constant. It means that the plasma confinement lies in saturation ohmic confinement regime rather than the linear Neo-Alcator regime causing weak density dependence in the previous theoretical studies.

  11. Low-resistance and highly transparent Ag/IZO ohmic contact to p-type GaN

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Han-Ki, E-mail: imdlhkkim@khu.ac.k [Department of Display Materials Engineering, Kyung Hee University, 1 Seochoen-dong, Yongin-si, Gyeonggi-do 446-701 (Korea, Republic of); Yi, Min-Su [Department of Materials Science and Engineering, Kyungpook National University, Sangju, Gyeongbuk, 742-711 (Korea, Republic of); Lee, Sung-Nam [Department of Engineering in Energy and Applied Chemistry, Silla University, Busan, 617-736 (Korea, Republic of)

    2009-05-29

    The electrical, structural, and optical characteristics of Ag/ZnO-doped In{sub 2}O{sub 3} (IZO) ohmic contacts to p-type GaN:Mg (2.5 x 10{sup 17} cm{sup -3}) were investigated. The Ag and IZO (10 nm/50 nm) layers were prepared by thermal evaporation and linear facing target sputtering, respectively. Although the as-deposited and 400 {sup o}C annealed samples showed rectifying behavior, the 500 and 600 {sup o}C annealed samples showed linear I-V characteristics indicative of the formation of an ohmic contact. The annealing of the contact at 600 {sup o}C for 3 min in a vacuum ({approx} 10{sup -3} Torr) resulted in the lowest specific contact resistivity of 1.8 x 10{sup -4} {Omega}.cm{sup 2} and high transparency of 78% at a wavelength of 470 nm. Using Auger electron spectroscopy, depth profiling and synchrotron X-ray scattering analysis, we suggested a possible mechanism to explain the annealing dependence of the electrical properties of the Ag/IZO contacts.

  12. Postannealing Effect at Various Gas Ambients on Ohmic Contacts of Pt/ZnO Nanobilayers toward Ultraviolet Photodetectors

    Directory of Open Access Journals (Sweden)

    Chung-Hua Chao

    2013-01-01

    Full Text Available This paper describes a fabrication and characterization of ultraviolet (UV photodetectors based on Ohmic contacts using Pt electrode onto the epitaxial ZnO (0002 thin film. Plasma enhanced chemical vapor deposition (PECVD system was employed to deposit ZnO (0002 thin films onto silicon substrates, and radio-frequency (RF magnetron sputtering was used to deposit Pt top electrode onto the ZnO thin films. The as-deposited Pt/ZnO nanobilayer samples were then annealed at 450∘C in two different ambients (argon and nitrogen to obtain optimal Ohmic contacts. The crystal structure, surface morphology, optical properties, and wettability of ZnO thin films were analyzed by X-ray diffraction (XRD, field emission scanning electron microscopy (FE-SEM, atomic force microscopy (AFM, photoluminescence (PL, UV-Vis-NIR spectrophotometer, and contact angle meter, respectively. Moreover, the photoconductivity of the Pt/ZnO nanobilayers was also investigated for UV photodetector application. The above results showed that the optimum ZnO sample was synthesized with gas flow rate ratio of 1 : 3 diethylzinc [DEZn, Zn(C2H52] to carbon dioxide (CO2 and then combined with Pt electrode annealed at 450∘C in argon ambient, exhibiting good crystallinity as well as UV photo responsibility.

  13. Microstructure of V-based ohmic contacts to AlGaN/GaN heterostructures at a reduced annealing temperature

    Energy Technology Data Exchange (ETDEWEB)

    Schmid, A., E-mail: alexander.schmid@physik.tu-freiberg.de; Schroeter, Ch.; Otto, R.; Heitmann, J. [Institute of Applied Physics, TU Bergakademie Freiberg, 09599 Freiberg (Germany); Schuster, M. [Namlab gGmbH, 01187 Dresden (Germany); Klemm, V.; Rafaja, D. [Institute of Materials Science, TU Bergakademie Freiberg, 09599 Freiberg (Germany)

    2015-02-02

    Ohmic contacts with V/Al/Ni/Au and V/Ni/Au metalization schemes were deposited on AlGaN/GaN heterostructures. The dependence of the specific contact resistance on the annealing conditions and the V:Al thickness ratio was shown. For an optimized electrode stack, a low specific contact resistance of 8.9 × 10{sup −6} Ω cm{sup 2} was achieved at an annealing temperature of 650 °C. Compared to the conventional Ti/Al/Ni/Au contact, this is a reduction of 150 K. The microstructure and contact formation at the AlGaN/metal interface were investigated by transmission electron microscopy including high-resolution micrographs and energy dispersive X-ray analysis. It was shown that for low-resistive contacts, the resistivity of the metalization has to be taken into account. The V:Al thickness ratio has an impact on the formation of different intermetallic phases and thus is crucial for establishing ohmic contacts at reduced annealing temperatures.

  14. The role of creep in the time-dependent resistance of Ohmic gold contacts in radio frequency microelectromechanical system devices

    Science.gov (United States)

    Rezvanian, O.; Brown, C.; Zikry, M. A.; Kingon, A. I.; Krim, J.; Irving, D. L.; Brenner, D. W.

    2008-07-01

    It is shown that measured and calculated time-dependent electrical resistances of closed gold Ohmic switches in radio frequency microelectromechanical system (rf-MEMS) devices are well described by a power law that can be derived from a single asperity creep model. The analysis reveals that the exponent and prefactor in the power law arise, respectively, from the coefficient relating creep rate to applied stress and the initial surface roughness. The analysis also shows that resistance plateaus are not, in fact, limiting resistances but rather result from the small coefficient in the power law. The model predicts that it will take a longer time for the contact resistance to attain a power law relation with each successive closing of the switch due to asperity blunting. Analysis of the first few seconds of the measured resistance for three successive openings and closings of one of the MEMS devices supports this prediction. This work thus provides guidance toward the rational design of Ohmic contacts with enhanced reliabilities by better defining variables that can be controlled through material selection, interface processing, and switch operation.

  15. Sequence analysis of cereal sucrose synthase genes and isolation ...

    African Journals Online (AJOL)

    SERVER

    2007-10-18

    Oct 18, 2007 ... sequencing of sucrose synthase gene fragment from sor- ghum using primers designed at their conserved exons. MATERIALS AND METHODS. Multiple sequence alignment. Sucrose synthase gene sequences of various cereals like rice, maize, and barley were accessed from NCBI Genbank database.

  16. Prostaglandin H synthase immunoreactivity in human gut. An immunohistochemical study

    DEFF Research Database (Denmark)

    Mikkelsen, H B; Rumessen, J J; Qvortrup, Klaus

    1991-01-01

    Prostaglandins exhibit a variety of actions on intestinal smooth muscle depending upon the type, dose and muscle layer studied. As the cellular origin of prostaglandin H (PGH) synthase has not been established with certainty in the human gut wall, we studied the localization of PGH synthase...

  17. Localization of nitric oxide synthase in human skeletal muscle

    DEFF Research Database (Denmark)

    Frandsen, Ulrik; Lopez-Figueroa, M.; Hellsten, Ylva

    1996-01-01

    The present study investigated the cellular localization of the neuronal type I and endothelial type III nitric oxide synthase in human skeletal muscle. Type I NO synthase immunoreactivity was found in the sarcolemma and the cytoplasm of all muscle fibres. Stronger immunoreactivity was expressed...

  18. Effects of nanoscale coatings on reliability of MEMS ohmic contact switches

    Science.gov (United States)

    Tremper, Amber Leigh

    also increases the dependence on force. This thesis also details that the relative contribution of contact resistance to the total measured resistance can be maximized by decreasing the probe spacing and tip radius. AFM testing of the layered systems showed that the coated samples had larger predicted plane strain moduli than the Au sample, in contrast to the nanoindentation testing. Thus, when the contact depth was kept sufficiently small, the contact stiffness increased as predicted by substrate models. When the contact depth was on the order of the coating thickness, the contact stiffness actually decreased. Additionally, the forceseparation plots showed that the Ru and Pt surfaces either accumulated large amounts of contamination or were less susceptible to being wiped clean than the Au film. Further, scratch testing of the Au film and Ru and Pt coatings show that the hard surface coatings reduce material removal and contact wear. Ultra-thin Ru and Pt surface coatings on Au films are shown to be improved material systems for ohmic contact switches. The wear is reduced for coated materials, while the resistance and power consumption through the coating are not significantly affected.

  19. Combined use of a field-plate and narrow p-barriers for a wide-pitch ohmic-side readout of the BELLE double-sided SVD

    International Nuclear Information System (INIS)

    Ikeda, H.; Matsuda, T.

    1997-01-01

    We explored wide-pitch ohmic-side structures for the BELLE SVD, where we proposed a field-plate structure combined with narrow p-barriers in between the readout electrodes of 90, 113, 180, and 226 μm-pitch detectors. The effect of the p-barriers was studied with a numerical model to trace the carrier trajectories. The charge collection and sharing properties were examined in practice for prototype small-size detectors with an IR pulse shining from either the junction side or the ohmic side. The channel separation capabilities were also shown to be appropriate under nominal operation conditions. (orig.)

  20. Heat conduction

    International Nuclear Information System (INIS)

    Grigull, U.; Sandner, H.

    1984-01-01

    Included are discussions of rates of heat transfer by conduction, the effects of varying and changing properties, thermal explosions, distributed heat sources, moving heat sources, and non-steady three-dimensional conduction processes. Throughout, the importance of thinking both numerically and symbolically is stressed, as this is essential to the development of the intuitive understanding of numerical values needed for successful designing. Extensive tables of thermophysical properties, including thermal conductivity and diffusivity, are presented. Also included are exact and approximate solutions to many of the problems that arise in practical situations

  1. A Comparison of the Effects of Neuronal Nitric Oxide Synthase and Inducible Nitric Oxide Synthase Inhibition on Cartilage Damage

    Directory of Open Access Journals (Sweden)

    Nevzat Selim Gokay

    2016-01-01

    Full Text Available The objective of this study was to investigate the effects of selective inducible nitric oxide synthase and neuronal nitric oxide synthase inhibitors on cartilage regeneration. The study involved 27 Wistar rats that were divided into five groups. On Day 1, both knees of 3 rats were resected and placed in a formalin solution as a control group. The remaining 24 rats were separated into 4 groups, and their right knees were surgically damaged. Depending on the groups, the rats were injected with intra-articular normal saline solution, neuronal nitric oxide synthase inhibitor 7-nitroindazole (50 mg/kg, inducible nitric oxide synthase inhibitor amino-guanidine (30 mg/kg, or nitric oxide precursor L-arginine (200 mg/kg. After 21 days, the right and left knees of the rats were resected and placed in formalin solution. The samples were histopathologically examined by a blinded evaluator and scored on 8 parameters. Although selective neuronal nitric oxide synthase inhibition exhibited significant (P=0.044 positive effects on cartilage regeneration following cartilage damage, it was determined that inducible nitric oxide synthase inhibition had no statistically significant effect on cartilage regeneration. It was observed that the nitric oxide synthase activation triggered advanced arthrosis symptoms, such as osteophyte formation. The fact that selective neuronal nitric oxide synthase inhibitors were observed to have mitigating effects on the severity of the damage may, in the future, influence the development of new agents to be used in the treatment of cartilage disorders.

  2. Electrical Conductivity.

    Science.gov (United States)

    Hershey, David R.; Sand, Susan

    1993-01-01

    Explains how electrical conductivity (EC) can be used to measure ion concentration in solutions. Describes instrumentation for the measurement, temperature dependence and EC, and the EC of common substances. (PR)

  3. Conduct Disorder

    Science.gov (United States)

    ... objections runs away from home often truant from school Children who exhibit these behaviors should receive a comprehensive evaluation by an experience mental health professional. Many children with a conduct disorder may ...

  4. Homospermidine synthase, the first pathway-specific enzyme of pyrrolizidine alkaloid biosynthesis, evolved from deoxyhypusine synthase

    Science.gov (United States)

    Ober, Dietrich; Hartmann, Thomas

    1999-01-01

    Pyrrolizidine alkaloids are preformed plant defense compounds with sporadic phylogenetic distribution. They are thought to have evolved in response to the selective pressure of herbivory. The first pathway-specific intermediate of these alkaloids is the rare polyamine homospermidine, which is synthesized by homospermidine synthase (HSS). The HSS gene from Senecio vernalis was cloned and shown to be derived from the deoxyhypusine synthase (DHS) gene, which is highly conserved among all eukaryotes and archaebacteria. DHS catalyzes the first step in the activation of translation initiation factor 5A (eIF5A), which is essential for eukaryotic cell proliferation and which acts as a cofactor of the HIV-1 Rev regulatory protein. Sequence comparison provides direct evidence for the evolutionary recruitment of an essential gene of primary metabolism (DHS) for the origin of the committing step (HSS) in the biosynthesis of pyrrolizidine alkaloids. PMID:10611289

  5. Nitric oxide synthase gene G298 allele

    International Nuclear Information System (INIS)

    Nagib El-Kilany, Galal E.; Nayel, Ehab; Hazzaa, Sahar

    2004-01-01

    Background: Nitric oxide (NO) has an important effect on blood pressure, arterial wall, and the basal release of endothelial NO in hypertension (HPN) may be reduced. Until now, there is no solid data revealing the potential role of the polymorphism of the nitric oxide synthase gene (NOS) in patients with HPN and microvascular angina. Aim: The aim of the present study is to investigate the gene of endothelial nitric oxide synthase (eNOS), as the polymorphism of this gene may be a putative candidate for HPN and initiate the process of atherosclerosis. Methods: Sixty participants were recruited for this study; 50 were hypertensive patients complaining of chest pain [30 of them have electrocardiogram (EKG) changes of ischemia], 20 had isolated HPN, and 10 healthy volunteers served as control. All patients underwent stress myocardial perfusion imaging (MPI) and coronary angiography. Genotyping of eNOS for all patients and controls was performed. The linkages between HPN, microvascular angina and eNOS gene polymorphism were investigated. Results: MPI and coronary angiography revealed that 15 patients had chest pain with true ischemia and reversible myocardial perfusion defects (multiple and mild) but normal epicardial coronary arteries (microvascular angina), while 15 patients had significant coronary artery disease (CAD), and 20 hypertensive patients showed normal perfusion scan and coronary angiography. The prevalence of the NOS G 298 allele was higher in the hypertensive group with microvascular angina (documented by MPI) than it was among the control participants (P<.005). The eNOS allele was significantly higher in the hypertensive group than in the control participants, but there was no significant difference in homozygote mutants among hypertensive participants, x-syndrome and patients with CAD. Conclusion: eNOS gene polymorphism is proved to be an important etiology in microvascular angina (x-syndrome) among hypertensive patients. In addition, the eNOS mutant

  6. Glycogen synthase activation by sugars in isolated hepatocytes.

    Science.gov (United States)

    Ciudad, C J; Carabaza, A; Bosch, F; Gòmez I Foix, A M; Guinovart, J J

    1988-07-01

    We have investigated the activation by sugars of glycogen synthase in relation to (i) phosphorylase a activity and (ii) changes in the intracellular concentration of glucose 6-phosphate and adenine nucleotides. All the sugars tested in this work present the common denominator of activating glycogen synthase. On the other hand, phosphorylase a activity is decreased by mannose and glucose, unchanged by galactose and xylitol, and increased by tagatose, glyceraldehyde, and fructose. Dihydroxyacetone exerts a biphasic effect on phosphorylase. These findings provide additional evidence proving that glycogen synthase can be activated regardless of the levels of phosphorylase a, clearly establishing that a nonsequential mechanism for the activation of glycogen synthase occurs in liver cells. The glycogen synthase activation state is related to the concentrations of glucose 6-phosphate and adenine nucleotides. In this respect, tagatose, glyceraldehyde, and fructose deplete ATP and increase AMP contents, whereas glucose, mannose, galactose, xylitol, and dihydroxyacetone do not alter the concentration of these nucleotides. In addition, all these sugars, except glyceraldehyde, increase the intracellular content of glucose 6-phosphate. The activation of glycogen synthase by sugars is reflected in decreases on both kinetic constants of the enzyme, M0.5 (for glucose 6-phosphate) and S0.5 (for UDP-glucose). We propose that hepatocyte glycogen synthase is activated by monosaccharides by a mechanism triggered by changes in glucose 6-phosphate and adenine nucleotide concentrations which have been described to modify glycogen synthase phosphatase activity. This mechanism represents a metabolite control of the sugar-induced activation of hepatocyte glycogen synthase.

  7. Conduct disorders

    NARCIS (Netherlands)

    Buitelaar, J.K.; Smeets, K.C.; Herpers, P.; Scheepers, F.; Glennon, J.; Rommelse, N.N.J.

    2013-01-01

    Conduct disorder (CD) is a frequently occurring psychiatric disorder characterized by a persistent pattern of aggressive and non-aggressive rule breaking antisocial behaviours that lead to considerable burden for the patients themselves, their family and society. This review paper updates diagnostic

  8. Quench of non-Markovian coherence in the deep sub-Ohmic spin–boson model: A unitary equilibration scheme

    International Nuclear Information System (INIS)

    Yao, Yao

    2015-01-01

    The deep sub-Ohmic spin–boson model shows a longstanding non-Markovian coherence at low temperature. Motivating to quench this robust coherence, the thermal effect is unitarily incorporated into the time evolution of the model, which is calculated by the adaptive time-dependent density matrix renormalization group algorithm combined with the orthogonal polynomials theory. Via introducing a unitary heating operator to the bosonic bath, the bath is heated up so that a majority portion of the bosonic excited states is occupied. It is found in this situation the coherence of the spin is quickly quenched even in the coherent regime, in which the non-Markovian feature dominates. With this finding we come up with a novel way to implement the unitary equilibration, the essential term of the eigenstate-thermalization hypothesis, through a short-time evolution of the model

  9. Formation of an internal transport barrier in the ohmic H-mode in the TUMAN-3M tokamak

    International Nuclear Information System (INIS)

    Andrejko, M.V.; Askinazi, L.G.; Golant, V.E.; Zhubr, N.A.; Kornev, V.A.; Krikunov, S.V.; Lebedev, S.V.; Levin, L.S.; Razdobarin, G.T.; Rozhdestvensky, V.V.; Smirnov, A.I.; Tukachinsky, A.S.; Yaroshevich, S.P.

    2000-01-01

    In experiments on studying the ohmic H-mode in the TUMAN-3M tokamak, it is found that, in high-current (I p ∼ 120-170 kA) discharges, a region with high electron-temperature and density gradients is formed in the plasma core. In this case, the energy confinement time τ E attains 9-18 ms, which is nearly twice as large as that predicted by the ELM-free ITER-93H scaling. This is evidence that the internal transport barrier in a plasma can exist without auxiliary heating. Calculations of the effective thermal diffusivity by the ASTRA transport code demonstrate a strong suppression of heat transport in the region where the temperature and density gradients are high

  10. Ohmic contacts to n+-GaN capped AlGaN/AlN/GaN high electron mobility transistors

    International Nuclear Information System (INIS)

    Wang Liang; Mohammed, Fitih M.; Ofuonye, Benedict; Adesida, Ilesanmi

    2007-01-01

    Investigations of Ti/Al/Mo/Au Ohmic contact formation, premetallization plasma treatment effects, and interfacial reactions for n + -GaN capped AlGaN/AlN/GaN heterostructures are presented. Ti thickness played an important role in determining contact performance. Transmission electron microscopy studies confirmed that thick Ti layer was necessary to fully consume the GaN cap and the top of AlGaN to enable a higher tunneling current flow. A direct correlation of plasma treatment conditions with I-V linearity, current level, and contact performance was established. The plasma-affected region is believed to extend over 20 nm into the AlGaN and GaN

  11. An “ohmic-first” self-terminating gate-recess technique for normally-off Al2O3/GaN MOSFET

    Science.gov (United States)

    Wang, Hongyue; Wang, Jinyan; Li, Mengjun; He, Yandong; Wang, Maojun; Yu, Min; Wu, Wengang; Zhou, Yang; Dai, Gang

    2018-04-01

    In this article, an ohmic-first AlGaN/GaN self-terminating gate-recess etching technique was demonstrated where ohmic contact formation is ahead of gate-recess-etching/gate-dielectric-deposition (GRE/GDD) process. The ohmic contact exhibits few degradations after the self-terminating gate-recess process. Besides, when comparing with that using the conventional fabrication process, the fabricated device using the ohmic-first fabrication process shows a better gate dielectric quality in terms of more than 3 orders lower forward gate leakage current, more than twice higher reverse breakdown voltage as well as better stability. Based on this proposed technique, the normally-off Al2O3/GaN MOSFET exhibits a threshold voltage (V th) of ˜1.8 V, a maximum drain current of ˜328 mA/mm, a forward gate leakage current of ˜10-6 A/mm and an off-state breakdown voltage of 218 V at room temperature. Meanwhile, high temperature characteristics of the device was also evaluated and small variations (˜7.6%) of the threshold voltage was confirmed up to 300 °C.

  12. Generation and Functional Evaluation of Designer Monoterpene Synthases.

    Science.gov (United States)

    Srividya, N; Lange, I; Lange, B M

    2016-01-01

    Monoterpene synthases are highly versatile enzymes that catalyze the first committed step in the pathways toward terpenoids, the structurally most diverse class of plant natural products. Recent advancements in our understanding of the reaction mechanism have enabled engineering approaches to develop mutant monoterpene synthases that produce specific monoterpenes. In this chapter, we are describing protocols to introduce targeted mutations, express mutant enzyme catalysts in heterologous hosts, and assess their catalytic properties. Mutant monoterpene synthases have the potential to contribute significantly to synthetic biology efforts aimed at producing larger amounts of commercially attractive monoterpenes. © 2016 Elsevier Inc. All rights reserved.

  13. Geranylfarnesyl diphosphate synthase from Methanosarcina mazei: Different role, different evolution

    International Nuclear Information System (INIS)

    Ogawa, Takuya; Yoshimura, Tohru; Hemmi, Hisashi

    2010-01-01

    The gene of (all-E) geranylfarnesyl diphosphate synthase that is responsible for the biosynthesis of methanophenazine, an electron carrier utilized for methanogenesis, was cloned from a methanogenic archaeon Methanosarcina mazei Goe1. The properties of the recombinant enzyme and the results of phylogenetic analysis suggest that the enzyme is closely related to (all-E) prenyl diphosphate synthases that are responsible for the biosynthesis of respiratory quinones, rather than to the enzymes involved in the biosynthesis of archaeal membrane lipids, including (all-E) geranylfarnesyl diphosphate synthase from a thermophilic archaeon.

  14. Evolution of the Turbulence Radial Wavenumber Spectrum near the L-H Transition in NSTX Ohmic Discharges

    Energy Technology Data Exchange (ETDEWEB)

    Kubota, S.; Peebles, W.A., E-mail: skubota@ucla.edu [UCLA, Los Angeles (United States); Bush, C. E.; Maingi, R. [Oak Ridge National Laboratory, Oak Ridge (United States); Zweben, S. J.; Bell, R.; Crocker, N.; Diallo, A.; Kaye, S.; LeBlanc, B. P.; Park, J. K.; Ren, Y. [Princeton Plasma Physics Laboratory, Princeton University, Princeton (United States); Maqueda, R. J. [Nova Photonics, Princeton (United States); Raman, R. [University of Washington, Seattle (United States)

    2012-09-15

    Full text: The measurement of radially extended meso-scale structures such as zonal flows and streamers, as well as the underlying microinstabilities driving them, is critical for understanding turbulence-driven transport in plasma devices. In particular, the shape and evolution of the radial wavenumber spectrum indicate details of the nonlinear spectral energy transfer, the spreading of turbulence, as well as the formation of transport barriers. In the National Spherical Torus Experiment (NSTX), the FMCW backscattering diagnostic is used to probe the turbulence radial wavenumber spectrum (k{sub r} = 0 - 22 cm-1 ) across the outboard minor radius near the L- to H-mode transition in Ohmic discharges. During the L-mode phase, a broad spectral component (k{sub r} {approx} 2 - 10 cm{sup -1} ) extends over a significant portion of the edge-core from R = 120 to 155 cm ({rho} = 0.4 - 0.95). At the L-H transition, turbulence is quenched across the measurable k{sub r} range at the ETB location, where the radial correlation length drops from {approx} 1.5 - 0.5 cm. The k{sub r} spectrum away from the ETB location is modified on a time scale of tens of microseconds, indicating that nonlocal turbulence dynamics are playing a strong role. Close to the L-H transition, oscillations in the density gradient and edge turbulence quenching become highly correlated. These oscillations are also present in Ohmic discharges without an L-H transition, but are far less frequent. Similar behavior is also seen near the L-H transition in NB-heated discharges. (author)

  15. Electrical conduction in 100 keV Kr+ ion implanted poly (ethylene terephthalate)

    Science.gov (United States)

    Goyal, P. K.; Kumar, V.; Gupta, Renu; Mahendia, S.; Anita, Kumar, S.

    2012-06-01

    Polyethylene terephthalate (PET) samples have been implanted to 100 keV Kr+ ions at the fluences 1×1015-- 1×1016 cm-2. From I-V characteristics, the conduction mechanism was found to be shifted from ohmic to space charge limited conduction (SCLC) after implantation. The surface conductivity of these implanted samples was found to increase with increasing implantation dose. The structural alterations in the Raman spectra of implanted PET samples indicate that such an increase in the conductivity may be attributed to the formation of conjugated double bonded carbonaceous structure in the implanted layer of PET.

  16. THREE-DIMENSIONAL ATMOSPHERIC CIRCULATION MODELS OF HD 189733b AND HD 209458b WITH CONSISTENT MAGNETIC DRAG AND OHMIC DISSIPATION

    International Nuclear Information System (INIS)

    Rauscher, Emily; Menou, Kristen

    2013-01-01

    We present the first three-dimensional circulation models for extrasolar gas giant atmospheres with geometrically and energetically consistent treatments of magnetic drag and ohmic dissipation. Atmospheric resistivities are continuously updated and calculated directly from the flow structure, strongly coupling the magnetic effects with the circulation pattern. We model the hot Jupiters HD 189733b (T eq ≈ 1200 K) and HD 209458b (T eq ≈ 1500 K) and test planetary magnetic field strengths from 0 to 30 G. We find that even at B = 3 G the atmospheric structure and circulation of HD 209458b are strongly influenced by magnetic effects, while the cooler HD 189733b remains largely unaffected, even in the case of B = 30 G and super-solar metallicities. Our models of HD 209458b indicate that magnetic effects can substantially slow down atmospheric winds, change circulation and temperature patterns, and alter observable properties. These models establish that longitudinal and latitudinal hot spot offsets, day-night flux contrasts, and planetary radius inflation are interrelated diagnostics of the magnetic induction process occurring in the atmospheres of hot Jupiters and other similarly forced exoplanets. Most of the ohmic heating occurs high in the atmosphere and on the dayside of the planet, while the heating at depth is strongly dependent on the internal heat flux assumed for the planet, with more heating when the deep atmosphere is hot. We compare the ohmic power at depth in our models, and estimates of the ohmic dissipation in the bulk interior (from general scaling laws), to evolutionary models that constrain the amount of heating necessary to explain the inflated radius of HD 209458b. Our results suggest that deep ohmic heating can successfully inflate the radius of HD 209458b for planetary magnetic field strengths of B ≥ 3-10 G.

  17. Phylogenomic and functional domain analysis of polyketide synthases in Fusarium

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Daren W.; Butchko, Robert A.; Baker, Scott E.; Proctor, Robert H.

    2012-02-01

    Fusarium species are ubiquitous in nature, cause a range of plant diseases, and produce a variety of chemicals often referred to as secondary metabolites. Although some fungal secondary metabolites affect plant growth or protect plants from other fungi and bacteria, their presence in grain based food and feed is more often associated with a variety of diseases in plants and in animals. Many of these structurally diverse metabolites are derived from a family of related enzymes called polyketide synthases (PKSs). A search of genomic sequence of Fusarium verticillioides, F. graminearum, F. oxysporum and Nectria haematococca (anamorph F. solani) identified a total of 58 PKS genes. To gain insight into how this gene family evolved and to guide future studies, we conducted a phylogenomic and functional domain analysis. The resulting genealogy suggested that Fusarium PKSs represent 34 different groups responsible for synthesis of different core metabolites. The analyses indicate that variation in the Fusarium PKS gene family is due to gene duplication and loss events as well as enzyme gain-of-function due to the acquisition of new domains or of loss-of-function due to nucleotide mutations. Transcriptional analysis indicate that the 16 F. verticillioides PKS genes are expressed under a range of conditions, further evidence that they are functional genes that confer the ability to produce secondary metabolites.

  18. Conservation and Role of Electrostatics in Thymidylate Synthase.

    Science.gov (United States)

    Garg, Divita; Skouloubris, Stephane; Briffotaux, Julien; Myllykallio, Hannu; Wade, Rebecca C

    2015-11-27

    Conservation of function across families of orthologous enzymes is generally accompanied by conservation of their active site electrostatic potentials. To study the electrostatic conservation in the highly conserved essential enzyme, thymidylate synthase (TS), we conducted a systematic species-based comparison of the electrostatic potential in the vicinity of its active site. Whereas the electrostatics of the active site of TS are generally well conserved, the TSs from minimal organisms do not conform to the overall trend. Since the genomes of minimal organisms have a high thymidine content compared to other organisms, the observation of non-conserved electrostatics was surprising. Analysis of the symbiotic relationship between minimal organisms and their hosts, and the genetic completeness of the thymidine synthesis pathway suggested that TS from the minimal organism Wigglesworthia glossinidia (W.g.b.) must be active. Four residues in the vicinity of the active site of Escherichia coli TS were mutated individually and simultaneously to mimic the electrostatics of W.g.b TS. The measured activities of the E. coli TS mutants imply that conservation of electrostatics in the region of the active site is important for the activity of TS, and suggest that the W.g.b. TS has the minimal activity necessary to support replication of its reduced genome.

  19. Laser diode with thermal conducting, current confining film

    Science.gov (United States)

    Hawrylo, Frank Z. (Inventor)

    1980-01-01

    A laser diode formed of a rectangular parallelopiped body of single crystalline semiconductor material includes regions of opposite conductivity type indium phosphide extending to opposite surfaces of the body. Within the body is a PN junction at which light can be generated. A stripe of a conductive material is on the surface of the body to which the P type region extends and forms an ohmic contact with the P type region. The stripe is spaced from the side surfaces of the body and extends to the end surfaces of the body. A film of germanium is on the portions of the surface of the P type region which is not covered by the conductive stripe. The germanium film serves to conduct heat from the body and forms a blocking junction with the P type region so as to confine the current through the body, across the light generating PN junction, away from the side surfaces of the body.

  20. Isolation of developing secondary xylem specific cellulose synthase ...

    Indian Academy of Sciences (India)

    The present study aimed at identifying developing secondary xylem specific cellulose synthase genes from .... the First strand cDNA synthesis kit (Fermentas, Pittsburgh,. USA). .... ing height of the rooted cutting, girth of the stem, leaf area.

  1. Cloning and expression of pineapple sucrose- phosphate synthase ...

    African Journals Online (AJOL)

    hope&shola

    2010-12-06

    Dec 6, 2010 ... phosphate; EDTA, ethylene diamine tetraacetic acid; Ivr, invertase; SS .... phenolics, tannins and artifacts due to differences of tissue composition ..... Banana sucrose-phosphate synthase gene expression during fruit ripening.

  2. Conductivity Probe

    Science.gov (United States)

    2008-01-01

    The Thermal and Electrical Conductivity Probe (TECP) for NASA's Phoenix Mars Lander took measurements in Martian soil and in the air. The needles on the end of the instrument were inserted into the Martian soil, allowing TECP to measure the propagation of both thermal and electrical energy. TECP also measured the humidity in the surrounding air. The needles on the probe are 15 millimeters (0.6 inch) long. The Phoenix Mission is led by the University of Arizona, Tucson, on behalf of NASA. Project management of the mission is by NASA's Jet Propulsion Laboratory, Pasadena, Calif. Spacecraft development is by Lockheed Martin Space Systems, Denver.

  3. Modulation of hyaluronan synthase activity in cellular membrane fractions

    OpenAIRE

    Vigetti, Davide; Genasetti, A; Karousou, Evgenia; Viola, Manuela; Clerici, M; Bartolini, B; Moretto, Paola; DE LUCA, Giancarlo; Hascall, Vc; Passi, Alberto

    2009-01-01

    Hyaluronan (HA), the only non-sulfated glycosaminoglycan, is involved in morphogenesis, wound healing, inflammation, angiogenesis, and cancer. In mammals, HA is synthesized by three homologous HA synthases, HAS1, HAS2, and HAS3, that polymerize the HA chain using UDP-glucuronic acid and UDP-N-acetylglucosamine as precursors. Since the amount of HA is critical in several pathophysiological conditions, we developed a non-radioactive assay for measuring the activity of HA synthases (HASs) in euk...

  4. Inhibitors of Fatty Acid Synthase for Prostate Cancer. Revision

    Science.gov (United States)

    2013-05-01

    acetyl- cholinesterase inhibitors have been developed, many with femtomolar binding affinities (7). This body of literature also confirms that the...AD_________________ Award Number: W81XWH-09-1-0204 TITLE: Inhibitors of Fatty Acid Synthase for...May 2013 2. REPORT TYPE Revised Final 3. DATES COVERED 01 May 2009-30 Apr 2013 4. TITLE AND SUBTITLE Inhibitors of Fatty Acid Synthase for

  5. Inhibitors of Fatty Acid Synthase for Prostate Cancer

    Science.gov (United States)

    2012-05-01

    compounds. For example, numerous classes of acetyl- cholinesterase inhibitors have been developed, m any with fe mtomolar binding affinities (7). This...AD_________________ Award Number: W81XWH-09-1-0204 TITLE: Inhibitors of Fatty Acid Synthase for...CONTRACT NUMBER Inhibitors of Fatty Acid Synthase for Prostate Cancer 5b. GRANT NUMBER W81XWH-09-1-0204 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR

  6. Homocystinuria due to cystathionine beta synthase deficiency

    Directory of Open Access Journals (Sweden)

    Rao T

    2008-01-01

    Full Text Available A two year-old male child presented with cutis marmorata congenita universalis, brittle hair, mild mental retardation, and finger spasms. Biochemical findings include increased levels of homocysteine in the blood-106.62 µmol/L (normal levels: 5.90-16µmol/L. Biochemical tests such as the silver nitroprusside and nitroprusside tests were positive suggesting homocystinuria. The patient was treated with oral pyridoxine therapy for three months. The child responded well to this therapy and the muscle spasms as well as skin manifestations such as cutis marmorata subsided. The treatment is being continued; the case is reported here because of its rarity. Homocysteinuria arising due to cystathionine beta-synthase (CBS deficiency is an autosomal recessive disorder of methionine metabolism that produces increased levels of urinary homocysteine and methionine It manifests itself in vascular, central nervous system, cutaneous, and connective tissue disturbances and phenotypically resembles Marfan′s syndrome. Skin manifestations include malar flush, thin hair, and cutis reticulata / marmorata.

  7. The Eucalyptus terpene synthase gene family.

    Science.gov (United States)

    Külheim, Carsten; Padovan, Amanda; Hefer, Charles; Krause, Sandra T; Köllner, Tobias G; Myburg, Alexander A; Degenhardt, Jörg; Foley, William J

    2015-06-11

    Terpenoids are abundant in the foliage of Eucalyptus, providing the characteristic smell as well as being valuable economically and influencing ecological interactions. Quantitative and qualitative inter- and intra- specific variation of terpenes is common in eucalypts. The genome sequences of Eucalyptus grandis and E. globulus were mined for terpene synthase genes (TPS) and compared to other plant species. We investigated the relative expression of TPS in seven plant tissues and functionally characterized five TPS genes from E. grandis. Compared to other sequenced plant genomes, Eucalyptus grandis has the largest number of putative functional TPS genes of any sequenced plant. We discovered 113 and 106 putative functional TPS genes in E. grandis and E. globulus, respectively. All but one TPS from E. grandis were expressed in at least one of seven plant tissues examined. Genomic clusters of up to 20 genes were identified. Many TPS are expressed in tissues other than leaves which invites a re-evaluation of the function of terpenes in Eucalyptus. Our data indicate that terpenes in Eucalyptus may play a wider role in biotic and abiotic interactions than previously thought. Tissue specific expression is common and the possibility of stress induction needs further investigation. Phylogenetic comparison of the two investigated Eucalyptus species gives insight about recent evolution of different clades within the TPS gene family. While the majority of TPS genes occur in orthologous pairs some clades show evidence of recent gene duplication, as well as loss of function.

  8. CONDUCTIVE CHANNEL FOR ENERGY TRANSMISSION

    Directory of Open Access Journals (Sweden)

    V. V. Apollonov

    2014-01-01

    Full Text Available Laser spark obtained by using a conical optics is much more appropriate to form conducting channels in atmosphere. Only two types of lasers are actively considered to be used in forming high-conductivity channels in atmosphere, controlled by laser spark: pulsed sub-microsecond gas and chemical lasers (CO2, DF and short pulse solid-state and UV lasers. Main advantage of short pulse lasers is their ability in forming of super long ionized channels with a characteristic diameter of ~100  µ  in atmosphere along the  beam propagation direction. At estimated electron densities below  10 ⋅ 16 cm–3 in these filaments and laser wavelengths in the range of 0,5–1,0 mm, the plasma barely absorbs laser radiation.  In this case, the length of the track composed of many filaments is determined by the laser intensity and may reach many kilometers at a femtosecond pulse energy of ~100 mJ. However, these lasers could not be used to form high-conductivity long channels in atmosphere. The ohmic resistance of this type a conducting channels turned out to be very high, and the gas in the channels could not be strongly heated (< 1 J. An electric breakdown controlled by radiation of femtosecond solid-state laser was implemented in only at a length of 3 m with a voltage of 2 MV across the discharge gap (670 kV/m.Not so long ago scientific group from P. N. Lebedev has improved that result, the discharge gap – 1 m had been broken under KrF laser irradiation when switching high-voltage (up to 390 kV/m electric discharge by 100-ns UV pulses. Our previous result  –  16 m long conducting channel controlled by a  laser spark at the voltage  –  3 MV  – was obtained more than 20 years ago in Russia and Japan by using pulsed CO2  laser with energy  –  0,5 kJ. An average electric field strength  was < 190 kV/m. It is still too much for efficient applications.

  9. Non-ohmic phenomena in Mn-doped BaTiO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Prades, Marta; Beltran, Hector; Cordoncillo, Eloisa [Departamento de Quimica Inorganica y Organica, Universitat Jaume I, Avda. Sos Baynat s/n, 12071 Castellon (Spain); Alonso, Pablo J. [Instituto de Ciencia de Materiales de Aragon, ICMA, Universidad de Zaragoza-C.S.I.C., C/Pedro Cerbuna 12, 50009 Zaragoza (Spain); Maso, Nahum; West, Anthony R. [Department of Materials Science and Engineering, University of Sheffield, Mappin Street, S1 3JD Sheffield (United Kingdom)

    2012-11-15

    We report here a novel effect in which the resistance of a semiconducting oxide ceramic increases on application of a small dc bias. The ceramic conducts at high temperatures by an n-type hopping mechanism. On application of a dc bias, conduction electrons are trapped at surface states and the resistance increases. On removal of the dc bias, the trapped electrons are released and the sample regains its original state. This effect is the mirror image of that seen with similar ceramics that conduct by a p-type mechanism whose resistance decreases reversibly on application of a small dc bias. These two phenomena together offer the possibility of novel switching devices and memristive applications, especially if the switching times can be reduced. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  10. Non-ohmic phenomena in Mn-doped BaTiO3

    International Nuclear Information System (INIS)

    Prades, Marta; Beltran, Hector; Cordoncillo, Eloisa; Alonso, Pablo J.; Maso, Nahum; West, Anthony R.

    2012-01-01

    We report here a novel effect in which the resistance of a semiconducting oxide ceramic increases on application of a small dc bias. The ceramic conducts at high temperatures by an n-type hopping mechanism. On application of a dc bias, conduction electrons are trapped at surface states and the resistance increases. On removal of the dc bias, the trapped electrons are released and the sample regains its original state. This effect is the mirror image of that seen with similar ceramics that conduct by a p-type mechanism whose resistance decreases reversibly on application of a small dc bias. These two phenomena together offer the possibility of novel switching devices and memristive applications, especially if the switching times can be reduced. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  11. On a two-layer Si_3N_4/SiO_2 dielectric mask for low-resistance ohmic contacts to AlGaN/GaN HEMTs

    International Nuclear Information System (INIS)

    Arutyunyan, S. S.; Pavlov, A. Yu.; Pavlov, B. Yu.; Tomosh, K. N.; Fedorov, Yu. V.

    2016-01-01

    The fabrication of a two-layer Si_3N_4/SiO_2 dielectric mask and features of its application in the technology of non-fired epitaxially grown ohmic contacts for high-power HEMTs on AlGaN/GaN heterostructures are described. The proposed Si_3N_4/SiO_2 mask allows the selective epitaxial growth of heavily doped ohmic contacts by nitride molecular-beam epitaxy and the fabrication of non-fired ohmic contacts with a resistance of 0.15–0.2 Ω mm and a smooth surface and edge morphology.

  12. Converting S-limonene synthase to pinene or phellandrene synthases reveals the plasticity of the active site.

    Science.gov (United States)

    Xu, Jinkun; Ai, Ying; Wang, Jianhui; Xu, Jingwei; Zhang, Yongkang; Yang, Dong

    2017-05-01

    S-limonene synthase is a model monoterpene synthase that cyclizes geranyl pyrophosphate (GPP) to form S-limonene. It is a relatively specific enzyme as the majority of its products are composed of limonene. In this study, we converted it to pinene or phellandrene synthases after introducing N345A/L423A/S454A or N345I mutations. Further studies on N345 suggest the polarity of this residue plays a critical role in limonene production by stabilizing the terpinyl cation intermediate. If it is mutated to a non-polar residue, further cyclization or hydride shifts occurs so the carbocation migrates towards the pyrophosphate, leading to the production of pinene or phellandrene. On the other hand, mutant enzymes that still possess a polar residue at this position produce limonene as the major product. N345 is not the only polar residue that may stabilize the terpinyl cation because it is not strictly conserved among limonene synthases across species and there are also several other polar residues in this area. These residues could form a "polar pocket" that may collectively play this stabilizing role. Our study provides important insights into the catalytic mechanism of limonene synthases. Furthermore, it also has wider implications on the evolution of terpene synthases. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Detection of inhomogeneities in membrane ohmic resistance in geometrically complex systems

    DEFF Research Database (Denmark)

    Svirskis, G; Hounsgaard, J; Gutman, A

    2000-01-01

    DC field-evoked transients in arbitrarily shaped neurons and syncytia were analyzed theoretically. In systems with homogeneous passive membrane properties, the transients develop much faster than the membrane discharges. Conductance of the proximal membrane could be larger due to the injury impos...

  14. Conduct disorders.

    Science.gov (United States)

    Buitelaar, Jan K; Smeets, Kirsten C; Herpers, Pierre; Scheepers, Floor; Glennon, Jeffrey; Rommelse, Nanda N J

    2013-02-01

    Conduct disorder (CD) is a frequently occurring psychiatric disorder characterized by a persistent pattern of aggressive and non-aggressive rule breaking antisocial behaviours that lead to considerable burden for the patients themselves, their family and society. This review paper updates diagnostic and therapeutic approaches to CD in the light of the forthcoming DSM-5 definition. The diagnostic criteria for CD will remain unchanged in DSM-5, but the introduction of a specifier of CD with a callous-unemotional (CU) presentation is new. Linked to this, we discuss the pros and cons of various other ways to subtype aggression/CD symptoms. Existing guidelines for CD are, with few exceptions, already of a relatively older date and emphasize that clinical assessment should be systematic and comprehensive and based on a multi-informant approach. Non-medical psychosocial interventions are recommended as the first option for the treatment of CD. There is a role for medication in the treatment of comorbid syndromes and/or in case of insufficient response to psychosocial interventions and severe and dangerous aggressive and violent behaviours.

  15. Sphingomyelin synthases regulate protein trafficking and secretion.

    Directory of Open Access Journals (Sweden)

    Marimuthu Subathra

    Full Text Available Sphingomyelin synthases (SMS1 and 2 represent a class of enzymes that transfer a phosphocholine moiety from phosphatidylcholine onto ceramide thus producing sphingomyelin and diacylglycerol (DAG. SMS1 localizes at the Golgi while SMS2 localizes both at the Golgi and the plasma membrane. Previous studies from our laboratory showed that modulation of SMS1 and, to a lesser extent, of SMS2 affected the formation of DAG at the Golgi apparatus. As a consequence, down-regulation of SMS1 and SMS2 reduced the localization of the DAG-binding protein, protein kinase D (PKD, to the Golgi. Since PKD recruitment to the Golgi has been implicated in cellular secretion through the trans golgi network (TGN, the effect of down-regulation of SMSs on TGN-to-plasma membrane trafficking was studied. Down regulation of either SMS1 or SMS2 significantly retarded trafficking of the reporter protein vesicular stomatitis virus G protein tagged with GFP (VSVG-GFP from the TGN to the cell surface. Inhibition of SMSs also induced tubular protrusions from the trans Golgi network reminiscent of inhibited TGN membrane fission. Since a recent study demonstrated the requirement of PKD activity for insulin secretion in beta cells, we tested the function of SMS in this model. Inhibition of SMS significantly reduced insulin secretion in rat INS-1 cells. Taken together these results provide the first direct evidence that both enzymes (SMS1 and 2 are capable of regulating TGN-mediated protein trafficking and secretion, functions that are compatible with PKD being a down-stream target for SMSs in the Golgi.

  16. The Tomato Terpene Synthase Gene Family1[W][OA

    Science.gov (United States)

    Falara, Vasiliki; Akhtar, Tariq A.; Nguyen, Thuong T.H.; Spyropoulou, Eleni A.; Bleeker, Petra M.; Schauvinhold, Ines; Matsuba, Yuki; Bonini, Megan E.; Schilmiller, Anthony L.; Last, Robert L.; Schuurink, Robert C.; Pichersky, Eran

    2011-01-01

    Compounds of the terpenoid class play numerous roles in the interactions of plants with their environment, such as attracting pollinators and defending the plant against pests. We show here that the genome of cultivated tomato (Solanum lycopersicum) contains 44 terpene synthase (TPS) genes, including 29 that are functional or potentially functional. Of these 29 TPS genes, 26 were expressed in at least some organs or tissues of the plant. The enzymatic functions of eight of the TPS proteins were previously reported, and here we report the specific in vitro catalytic activity of 10 additional tomato terpene synthases. Many of the tomato TPS genes are found in clusters, notably on chromosomes 1, 2, 6, 8, and 10. All TPS family clades previously identified in angiosperms are also present in tomato. The largest clade of functional TPS genes found in tomato, with 12 members, is the TPS-a clade, and it appears to encode only sesquiterpene synthases, one of which is localized to the mitochondria, while the rest are likely cytosolic. A few additional sesquiterpene synthases are encoded by TPS-b clade genes. Some of the tomato sesquiterpene synthases use z,z-farnesyl diphosphate in vitro as well, or more efficiently than, the e,e-farnesyl diphosphate substrate. Genes encoding monoterpene synthases are also prevalent, and they fall into three clades: TPS-b, TPS-g, and TPS-e/f. With the exception of two enzymes involved in the synthesis of ent-kaurene, the precursor of gibberellins, no other tomato TPS genes could be demonstrated to encode diterpene synthases so far. PMID:21813655

  17. Characterization of the human gene (TBXAS1) encoding thromboxane synthase.

    Science.gov (United States)

    Miyata, A; Yokoyama, C; Ihara, H; Bandoh, S; Takeda, O; Takahashi, E; Tanabe, T

    1994-09-01

    The gene encoding human thromboxane synthase (TBXAS1) was isolated from a human EMBL3 genomic library using human platelet thromboxane synthase cDNA as a probe. Nucleotide sequencing revealed that the human thromboxane synthase gene spans more than 75 kb and consists of 13 exons and 12 introns, of which the splice donor and acceptor sites conform to the GT/AG rule. The exon-intron boundaries of the thromboxane synthase gene were similar to those of the human cytochrome P450 nifedipine oxidase gene (CYP3A4) except for introns 9 and 10, although the primary sequences of these enzymes exhibited 35.8% identity each other. The 1.2-kb of the 5'-flanking region sequence contained potential binding sites for several transcription factors (AP-1, AP-2, GATA-1, CCAAT box, xenobiotic-response element, PEA-3, LF-A1, myb, basic transcription element and cAMP-response element). Primer-extension analysis indicated the multiple transcription-start sites, and the major start site was identified as an adenine residue located 142 bases upstream of the translation-initiation site. However, neither a typical TATA box nor a typical CAAT box is found within the 100-b upstream of the translation-initiation site. Southern-blot analysis revealed the presence of one copy of the thromboxane synthase gene per haploid genome. Furthermore, a fluorescence in situ hybridization study revealed that the human gene for thromboxane synthase is localized to band q33-q34 of the long arm of chromosome 7. A tissue-distribution study demonstrated that thromboxane synthase mRNA is widely expressed in human tissues and is particularly abundant in peripheral blood leukocyte, spleen, lung and liver. The low but significant levels of mRNA were observed in kidney, placenta and thymus.

  18. Liquid-infiltrated photonic crystals: Ohmic dissipation and broadening of modes

    DEFF Research Database (Denmark)

    Mortensen, Niels Asger; Ejsing, Louise Wellendorph; Xiao, Sanshui

    2006-01-01

    The pronounced light-matter interactions in photonic crystals make them interesting as opto-fludic "building blocks" for lab-on-a-chip applications. We show how conducting electrolytes cause dissipation and smearing of the density-of-states, thus altering decay dynamics of excited bio......-molecules dissolved in the electrolyte. Likewise, we find spatial damping of propagating modes, of the order dB/cm, for naturally occurring electrolytes such as drinking water or physiological salt water....

  19. Controlling interface oxygen for forming Ag ohmic contact to semi-polar (1 1 -2 2) plane p-type GaN

    Science.gov (United States)

    Park, Jae-Seong; Han, Jaecheon; Seong, Tae-Yeon

    2014-11-01

    Low-resistance Ag ohmic contacts to semi-polar (1 1 -2 2) p-GaN were developed by controlling interfacial oxide using a Zn layer. The 300 °C-annealed Zn/Ag samples showed ohmic behavior with a contact resistivity of 6.0 × 10-4 Ω cm2 better than that of Ag-only contacts (1.0 × 10-3 Ω cm2). The X-ray photoemission spectroscopy (XPS) results showed that annealing caused the indiffusion of oxygen at the contact/GaN interface, resulting in the formation of different types of interfacial oxides, viz. Ga-oxide and Ga-doped ZnO. Based on the XPS and electrical results, the possible mechanisms underlying the improved electrical properties of the Zn/Ag samples are discussed.

  20. Oxygen vacancy tuned Ohmic-Schottky conversion for enhanced performance in β-Ga{sub 2}O{sub 3} solar-blind ultraviolet photodetectors

    Energy Technology Data Exchange (ETDEWEB)

    Guo, D. Y.; Wu, Z. P.; An, Y. H.; Guo, X. C.; Chu, X. L.; Sun, C. L.; Tang, W. H., E-mail: whtang@bupt.edu.cn [School of Science, Beijing University of Posts and Telecommunications, Beijing 100876 (China); State Key Laboratory of Information Photonics and Optical Communications, Beijing University of Posts and Telecommunications, Beijing 100876 (China); Li, L. H. [Physics Department, The State University of New York at Potsdam, Potsdam, New York 13676-2294 (United States); Li, P. G., E-mail: pgli@zstu.edu.cn [School of Science, Beijing University of Posts and Telecommunications, Beijing 100876 (China); Center for Optoelectronics Materials and Devices, Department of Physics, Zhejiang Sci-Tech University, Hangzhou, 310018 Zhejiang (China)

    2014-07-14

    β-Ga{sub 2}O{sub 3} epitaxial thin films were deposited using laser molecular beam epitaxy technique and oxygen atmosphere in situ annealed in order to reduce the oxygen vacancy. Metal/semiconductor/metal structured photodetectors were fabricated using as-grown film and annealed film separately. Au/Ti electrodes were Ohmic contact with the as-grown films and Schottky contact with the annealed films. In compare with the Ohmic-type photodetector, the Schottky-type photodetector takes on lower dark current, higher photoresponse, and shorter switching time, which benefit from Schottky barrier controlling electron transport and the quantity of photogenerated carriers trapped by oxygen vacancy significant decreasing.

  1. Application of low frequency pulsed ohmic heating for inactivation of foodborne pathogens and MS-2 phage in buffered peptone water and tomato juice.

    Science.gov (United States)

    Kim, Sang-Soon; Choi, Won; Kang, Dong-Hyun

    2017-05-01

    The purpose of this study was to inactivate foodborne pathogens effectively by ohmic heating in buffered peptone water and tomato juice without causing electrode corrosion and quality degradation. Escherichia coli O157:H7, Salmonella Typhimurium, and Listeria monocytogenes were used as representative foodborne pathogens and MS-2 phage was used as a norovirus surrogate. Buffered peptone water and tomato juice inoculated with pathogens were treated with pulsed ohmic heating at different frequencies (0.06-1 kHz). Propidium iodide uptake values of bacterial pathogens were significantly (p heating is applicable to inactivate foodborne pathogens effectively without causing electrode corrosion and quality degradation in tomato juice. Copyright © 2016. Published by Elsevier Ltd.

  2. Ultralow nonalloyed Ohmic contact resistance to self aligned N-polar GaN high electron mobility transistors by In(Ga)N regrowth

    International Nuclear Information System (INIS)

    Dasgupta, Sansaptak; Nidhi,; Brown, David F.; Wu, Feng; Keller, Stacia; Speck, James S.; Mishra, Umesh K.

    2010-01-01

    Ultralow Ohmic contact resistance and a self-aligned device structure are necessary to reduce the effect of parasitic elements and obtain higher f t and f max in high electron mobility transistors (HEMTs). N-polar (0001) GaN HEMTs, offer a natural advantage over Ga-polar HEMTs, in terms of contact resistance since the contact is not made through a high band gap material [Al(Ga)N]. In this work, we extend the advantage by making use of polarization induced three-dimensional electron-gas through regrowth of graded InGaN and thin InN cap in the contact regions by plasma (molecular beam epitaxy), to obtain an ultralow Ohmic contact resistance of 27 Ω μm to a GaN 2DEG.

  3. Sucrose Phosphate Synthase and Sucrose Accumulation at Low Temperature 1

    Science.gov (United States)

    Guy, Charles L.; Huber, Joan L. A.; Huber, Steven C.

    1992-01-01

    The influence of growth temperature on the free sugar and sucrose phosphate synthase content and activity of spinach (Spinacia oleracea) leaf tissue was studied. When plants were grown at 25°C for 3 weeks and then transferred to a constant 5°C, sucrose, glucose, and fructose accumulated to high levels during a 14-d period. Predawn sugar levels increased from 14- to 20-fold over the levels present at the outset of the low-temperature treatment. Sucrose was the most abundant free sugar before, during, and after exposure to 5°C. Leaf sucrose phosphate synthase activity was significantly increased by the low-temperature treatment, whereas sucrose synthase and invertases were not. Synthesis of the sucrose phosphate synthase subunit was increased during and after low-temperature exposure and paralleled an increase in the steady-state level of the subunit. The increases in sucrose and its primary biosynthetic enzyme, sucrose phosphate synthase, are discussed in relation to adjustment of metabolism to low nonfreezing temperature and freezing stress tolerance. Images Figure 1 Figure 2 Figure 3 PMID:16652990

  4. Direct Observation of 2D Electrostatics and Ohmic Contacts in Template-Grown Graphene/WS2 Heterostructures.

    Science.gov (United States)

    Zheng, Changxi; Zhang, Qianhui; Weber, Bent; Ilatikhameneh, Hesameddin; Chen, Fan; Sahasrabudhe, Harshad; Rahman, Rajib; Li, Shiqiang; Chen, Zhen; Hellerstedt, Jack; Zhang, Yupeng; Duan, Wen Hui; Bao, Qiaoliang; Fuhrer, Michael S

    2017-03-28

    Large-area two-dimensional (2D) heterojunctions are promising building blocks of 2D circuits. Understanding their intriguing electrostatics is pivotal but largely hindered by the lack of direct observations. Here graphene-WS 2 heterojunctions are prepared over large areas using a seedless ambient-pressure chemical vapor deposition technique. Kelvin probe force microscopy, photoluminescence spectroscopy, and scanning tunneling microscopy characterize the doping in graphene-WS 2 heterojunctions as-grown on sapphire and transferred to SiO 2 with and without thermal annealing. Both p-n and n-n junctions are observed, and a flat-band condition (zero Schottky barrier height) is found for lightly n-doped WS 2 , promising low-resistance ohmic contacts. This indicates a more favorable band alignment for graphene-WS 2 than has been predicted, likely explaining the low barriers observed in transport experiments on similar heterojunctions. Electrostatic modeling demonstrates that the large depletion width of the graphene-WS 2 junction reflects the electrostatics of the one-dimensional junction between two-dimensional materials.

  5. Destruction of Bacillus cereus spores in a thick soy bean paste (doenjang) by continuous ohmic heating with five sequential electrodes.

    Science.gov (United States)

    Ryang, J H; Kim, N H; Lee, B S; Kim, C T; Rhee, M S

    2016-07-01

    This study selected spores from Bacillus cereus FSP-2 strain (the isolate from a commercial doenjang processing line) as the test strain which showed significantly higher thermal resistance (P 1·5 National Bureau of Standards units), treatment at 105°C for 60 s was selected and applied on a large scale (500 kg of product). Reliable and reproducible destruction of B. cereus spores occurred; the reductions achieved (to < 4 log CFU g(-1) ) met the Korean national standards. Scanning electron microscopy revealed microstructural alterations in the spores (shrinkage and a distorted outer spore coat). OH is an effective method for destroying B. cereus spores to ensure the microbiological quality and safety of a thick, highly viscous sauce. This study shows that an ohmic heating (OH) using a five sequential electrode system can effectively destroy highly heat-resistant Bacillus cereus spores which have been frequently found in a commercial doenjang processing line without perceivable quality change in the product. In addition, it may demonstrate high potential of the unique OH system used in this study that will further contribute to ensure microbiological quality and safety of crude sauces containing high levels of electrolyte other than doenjang as well. © 2016 The Society for Applied Microbiology.

  6. Role of stochasticity in turbulence and convective intermittent transport at the scrape off layer of Ohmic plasma in QUEST

    International Nuclear Information System (INIS)

    Banerjee, Santanu; Ishiguro, M.; Tashima, S.; Mishra, K.; Zushi, H.; Hanada, K.; Nakamura, K.; Idei, H.; Hasegawa, M.; Fujisawa, A.; Nagashima, Y.; Matsuoka, K.; Nishino, N.; Liu, H. Q.

    2014-01-01

    Statistical features of fluctuations are investigated using the fast camera imaging technique in the scrape of layer (SOL) of electron cyclotron resonance heated Ohmic plasma. Fluctuations in the SOL towards low field side are dominated by coherent convective structures (blobs). Two dimensional structures of the higher order moments (skewness s and kurtosis k) representing the shape of probability density function (PDF) are studied. s and k are seen to be functions of the magnetic field lines. s and k are consistently higher towards the bottom half of the vessel in the SOL showing the blob trajectory along the field lines from the top towards bottom of the vessel. Parabolic relation (k=As 2 +C) is observed between s and k near the plasma boundary, featuring steep density gradient region and at the far SOL. The coefficient A, obtained experimentally, indicates a shift of prominence from pure drift-wave instabilities towards fully developed turbulence. Numerical coefficients characterizing the Pearson system are derived which demonstrates the progressive deviation of the PDF from Gaussian towards gamma from the density gradient region, towards the far SOL. Based on a simple stochastic differential equation, a direct correspondence between the multiplicative noise amplitude, increased intermittency, and hence change in PDF is discussed

  7. Impact of Ohmic-Assisted Decoction on Bioactive Components Extracted from Yacon (Smallanthus sonchifolius Poepp. Leaves: Comparison with Conventional Decoction

    Directory of Open Access Journals (Sweden)

    Forough Khajehei

    2017-11-01

    Full Text Available Yacon (Smallanthus sonchifolius Poepp. leaves are a potentially rich source of bioactive compounds, such as phenolic acids and flavonoids. In this study, the effect of the extraction method (ohmic-assisted decoction (OH-DE and decoction (DE, yacon cultivar (red and white, and leaf age (young and old on the quality/quantity of extracted phytochemicals were investigated. Extraction yield, energy consumption, total phenolic content (TPC, total flavonoid content (TFC, ABTS and DPPH radical scavenging activity, and ferric reducing antioxidant power (FRAP were determined. Additionally, HPLC-DAD was used to identify the major individual phenolic and flavonoid compounds of yacon leaves. The results showed that a three-way interaction of process-variables (extraction method×yacon cultivar×age of leaves influenced the extraction yield, TPC, TFC, ABTS, and DPPH radical scavenging activity, and FRAP, significantly (p < 0.05. However, energy consumption of the extraction process was only affected by method of extraction (p < 0.05 and was halved when OH-DE was applied as compared to DE alone. Additionally, the phytochemical quality of extracts was either improved or comparable when OH-DE was used for extraction. Also, it was shown that yacon leaves contained considerable amounts of caffeic acid, chlorogenic acid, ferrulic acid, myricetin, p-coumaric acid, and rutin, while leaves of the red cultivar had higher contents of each compound compared to leaves of the white cultivar.

  8. Uncovering nonperturbative dynamics of the biased sub-Ohmic spin-boson model with variational matrix product states

    Science.gov (United States)

    Gonzalez-Ballestero, C.; Schröder, Florian A. Y. N.; Chin, Alex W.

    2017-09-01

    We study the dynamics of the biased sub-Ohmic spin-boson model by means of a time-dependent variational matrix product state (TDVMPS) algorithm. The evolution of both the system and the environment is obtained in the weak- and the strong-coupling regimes, respectively characterized by damped spin oscillations and by a nonequilibrium process where the spin freezes near its initial state, which are explicitly shown to arise from a variety of reactive environmental quantum dynamics. We also explore the rich phenomenology of the intermediate-coupling case, a nonperturbative regime where the system shows a complex dynamical behavior, combining features of both the weakly and the strongly coupled case in a sequential, time-retarded fashion. Our work demonstrates the potential of TDVMPS methods for exploring otherwise elusive, nonperturbative regimes of complex open quantum systems, and points to the possibilities of exploiting the qualitative, real-time modification of quantum properties induced by nonequilibrium bath dynamics in ultrafast transient processes.

  9. Investigation of optimum ohmic heating conditions for inactivation of Escherichia coli O157:H7, Salmonella enterica serovar Typhimurium, and Listeria monocytogenes in apple juice.

    Science.gov (United States)

    Park, Il-Kyu; Ha, Jae-Won; Kang, Dong-Hyun

    2017-05-19

    Control of foodborne pathogens is an important issue for the fruit juice industry and ohmic heating treatment has been considered as one of the promising antimicrobial interventions. However, to date, evaluation of the relationship between inactivation of foodborne pathogens and system performance efficiency based on differing soluble solids content of apple juice during ohmic heating treatment has not been well studied. This study aims to investigate effective voltage gradients of an ohmic heating system and corresponding sugar concentrations (°Brix) of apple juice for inactivating major foodborne pathogens (E. coli O157:H7, S. Typhimurium, and L. monocytogenes) while maintaining higher system performance efficiency. Voltage gradients of 30, 40, 50, and 60 V/cm were applied to 72, 48, 36, 24, and 18 °Brix apple juices. At all voltage levels, the lowest heating rate was observed in 72 °Brix apple juice and a similar pattern of temperature increase was shown in18-48 °Brix juice samples. System performance coefficients (SPC) under two treatment conditions (30 V/cm in 36 °Brix or 60 V/cm in 48 °Brix juice) were relatively greater than for other combinations. Meanwhile, 5-log reductions of the three foodborne pathogens were achieved after treatment for 60 s in 36 °Brix at 30 V/cm, but this same reduction was observed in 48 °Brix juice at 60 V/cm within 20 s without affecting product quality. With respect to both bactericidal efficiency and SPC values, 60 V/cm in 48 °Brix was the most effective ohmic heating treatment combination for decontaminating apple juice concentrates.

  10. Structural and electrical characterization of AuPtAlTi ohmic contacts to AlGaN/GaN with varying annealing temperature and Al content

    OpenAIRE

    Fay, Mike W.; Han, Y.; Brown, Paul D.; Harrison, Ian; Hilton, K.P.; Munday, A.; Wallis, D.; Balmer, R.S.; Uren, M.J.; Martin, T.

    2008-01-01

    The effect of varying annealing temperature and Al layer thickness on the structural and electrical characteristics of AuPtAlTi/AlGaN/GaN ohmic contact structures has been systematically investigated. The relationship between annealing temperature, Al content, interfacial microstructure, surface planarity and contact resistance is\\ud examined. In particular, the presence of a detrimental low temperature Pt-Al reaction is identified. This is implicated in both the requirement for a higher Al:T...

  11. Effect of rapid thermal annealing on the composition of Au/Ti/Al/Ti ohmic contacts for GaN-based microdevices

    International Nuclear Information System (INIS)

    Redondo-Cubero, A.; Ynsa, M.D.; Romero, M.F.; Alves, L.C.; Muñoz, E.

    2013-01-01

    The homogeneity of Au/Ti/Al/Ti ohmic contacts for AlGaN/GaN devices was analyzed as a function of the thickness of the Ti barrier (30 nm 50 nm, although several compositional deficiencies were identified in the distribution maps obtained with the ion microprobe, including the formation of craters. A clear interplay between Ti and Au was found, suggesting the relevance of lateral flows during the rapid thermal annealing

  12. Transport simulations of ohmic TFTR experiments with profile-consistent microinstability-based models for chi/sub e/ and chi/sub i/

    International Nuclear Information System (INIS)

    Redi, M.H.; Tang, W.M.; Efthimion, P.C.; Mikkelsen, D.R.; Schmidt, G.L.

    1987-03-01

    Transport simulations of ohmically heated TFTR experiments with recently developed profile-consistent microinstability models for the anomalous thermal diffusivities, chi/sub e/ and chi/sub i/, give good agreement with experimental data. The steady-state temperature profiles and the total energy confinement times, tau/sub e/, were found to agree for each of the ohmic TFTR experiments simulated, including three high radiation cases and two plasmas fueled by pellet injection. Both collisional and collisionless models are tested. The trapped-electron drift wave microinstability model results are consistent with the thermal confinement of large plasma ohmic experiments on TFTR. We also find that transport due to the toroidal ion temperature gradient (eta/sub i/) modes can cause saturation in tau/sub E/ at the highest densities comparable to that observed on TFTR and equivalent to a neoclassical anomaly factor of 3. Predictions based on stabilized eta/sub i/-mode-driven ion transport are found to be in agreement with the enhanced global energy confinement times for pellet-fueled plasmas. 33 refs., 26 figs., 4 tabs

  13. Electrical and structural properties of surfaces and interfaces in Ti/Al/Ni Ohmic contacts to p-type implanted 4H-SiC

    Science.gov (United States)

    Vivona, M.; Greco, G.; Bongiorno, C.; Lo Nigro, R.; Scalese, S.; Roccaforte, F.

    2017-10-01

    In this work, the electrical and structural properties of Ti/Al/Ni Ohmic contacts to p-type implanted silicon carbide (4H-SiC) were studied employing different techniques. With increasing the annealing temperature, an improvement of the electrical properties of the contacts is highlighted, until an Ohmic behavior is obtained at 950 °C, with a specific contact resistance ρc = 2.3 × 10-4 Ω cm2. A considerable intermixing of the metal layers occurred upon annealing, as a consequence of the formation of different phases, both in the uppermost part of the stack (mainly Al3Ni2) and at the interface with SiC, where the formation of preferentially aligned TiC is observed. The formation of an Ohmic contact was associated with the occurrence of the reaction and the disorder at the interface, where the current transport is dominated by the thermionic field emission mechanism with a barrier height of 0.56 eV.

  14. InAlN high electron mobility transistor Ti/Al/Ni/Au Ohmic contact optimisation assisted by in-situ high temperature transmission electron microscopy

    International Nuclear Information System (INIS)

    Smith, M. D.; Parbrook, P. J.; O'Mahony, D.; Conroy, M.; Schmidt, M.

    2015-01-01

    This paper correlates the micro-structural and electrical characteristics associated with annealing of metallic multi-layers typically used in the formation of Ohmic contacts to InAlN high electron mobility transistors. The multi-layers comprised Ti/Al/Ni/Au and were annealed via rapid thermal processing at temperatures up to 925 °C with electrical current-voltage analysis establishing the onset of Ohmic (linear IV) behaviour at 750–800 °C. In-situ temperature dependent transmission electron microscopy established that metallic diffusion and inter-mixing were initiated near a temperature of 500 °C. Around 800 °C, inter-diffusion of the metal and semiconductor (nitride) was observed, correlating with the onset of Ohmic electrical behaviour. The sheet resistance associated with the InAlN/AlN/GaN interface is highly sensitive to the anneal temperature, with the range depending on the Ti layer thickness. The relationship between contact resistivity and measurement temperature follow that predicted by thermionic field emission for contacts annealed below 850 °C, but deviated above this due to excessive metal-semiconductor inter-diffusion

  15. Evidence for reduction of the toroidal ITG instability in the transition from saturated to improved Ohmic confinement in the tokamak TEXTOR

    International Nuclear Information System (INIS)

    Kreter, A; Schweer, B; Tokar, M Z; Unterberg, B

    2003-01-01

    In high density Ohmically heated discharges in the tokamak TEXTOR a transition from the saturated Ohmic confinement (SOC) to the improved Ohmic confinement (IOC) was observed triggered by a sudden reduction of the external gas flow. The SOC-IOC transition was investigated regarding the influence of the toroidal ITG instability driven by the ion temperature gradient (ITG). The ion temperature profiles were measured with high radial resolution by means of charge-exchange recombination spectroscopy (CXRS) with a high-energetic diagnostic hydrogen beam recently installed at TEXTOR. On the basis of the measured ion temperature distributions the η i parameter (ratio of the density and ion temperature decay lengths) and the growth rate of the toroidal ITG instability were calculated. After the SOC-IOC transition η i drops and lies in a noticeably smaller radial region over the threshold for the toroidal ITG. In consequence of it, the IOC regime is characterized by a clear reduction of the ITG growth rate γ ITG which was calculated including finite Larmor radius effects. The steepening of the plasma density profile after the decrease of the external gas flow is the main reason for the reduction of the ITG growth rate and the subsequent confinement transition to the IOC regime

  16. Regulation of glycogen synthase kinase-3 during bipolar mania treatment.

    Science.gov (United States)

    Li, Xiaohong; Liu, Min; Cai, Zhuoji; Wang, Gang; Li, Xiaohua

    2010-11-01

    Bipolar disorder is a debilitating psychiatric illness presenting with recurrent mania and depression. The pathophysiology of bipolar disorder is poorly understood, and molecular targets in the treatment of bipolar disorder remain to be identified. Preclinical studies have suggested that glycogen synthase kinase-3 (GSK3) is a potential therapeutic target in bipolar disorder, but evidence of abnormal GSK3 in human bipolar disorder and its response to treatment is still lacking. This study was conducted in acutely ill type I bipolar disorder subjects who were hospitalized for a manic episode. The protein level and the inhibitory serine phosphorylation of GSK3 in peripheral blood mononuclear cells of bipolar manic and healthy control subjects were compared, and the response of GSK3 to antimanic treatment was evaluated. The levels of GSK3α and GSK3β in this group of bipolar manic subjects were higher than healthy controls. Symptom improvement during an eight-week antimanic treatment with lithium, valproate, and atypical antipsychotics was accompanied by a significant increase in the inhibitory serine phosphorylation of GSK3, but not the total level of GSK3, whereas concomitant electroconvulsive therapy treatment during a manic episode appeared to dampen the response of GSK3 to pharmacological treatment. Results of this study suggest that GSK3 can be modified during the treatment of bipolar mania. This finding in human bipolar disorder is in agreement with preclinical data suggesting that inhibition of GSK3 by increasing serine phosphorylation is a response of GSK3 to psychotropics used in bipolar disorder, supporting the notion that GSK3 is a promising molecular target in the pharmacological treatment of bipolar disorder. © 2010 John Wiley and Sons A/S.

  17. Bornyl-diphosphate synthase from Lavandula angustifolia: A major monoterpene synthase involved in essential oil quality.

    Science.gov (United States)

    Despinasse, Yolande; Fiorucci, Sébastien; Antonczak, Serge; Moja, Sandrine; Bony, Aurélie; Nicolè, Florence; Baudino, Sylvie; Magnard, Jean-Louis; Jullien, Frédéric

    2017-05-01

    Lavender essential oils (EOs) of higher quality are produced by a few Lavandula angustifolia cultivars and mainly used in the perfume industry. Undesirable compounds such as camphor and borneol are also synthesized by lavender leading to a depreciated EO. Here, we report the cloning of bornyl diphosphate synthase of lavender (LaBPPS), an enzyme that catalyzes the production of bornyl diphosphate (BPP) and then by-products such as borneol or camphor, from an EST library. Compared to the BPPS of Salvia officinalis, the functional characterization of LaBPPS showed several differences in amino acid sequence, and the distribution of catalyzed products. Molecular modeling of the enzyme's active site suggests that the carbocation intermediates are more stable in LaBPPS than in SoBPPS leading probably to a lower efficiency of LaBPPS to convert GPP into BPP. Quantitative RT-PCR performed from leaves and flowers at different development stages of L. angustifolia samples show a clear correlation between transcript level of LaBPPS and accumulation of borneol/camphor, suggesting that LaBPPS is mainly responsible of in vivo biosynthesis of borneol/camphor in fine lavender. A phylogenetic analysis of terpene synthases (TPS) pointed out the basal position of LaBPPS in the TPSb clade, suggesting that LaBPPS could be an ancestor of others lavender TPSb. Finally, borneol could be one of the first monoterpenes to be synthesized in the Lavandula subgenus. Knowledge gained from these experiments will facilitate future studies to improve the lavender oils through metabolic engineering or plant breeding. Accession numbers: LaBPPS: KM015221. Copyright © 2017. Published by Elsevier Ltd.

  18. Sesquiterpene Synthase-3-Hydroxy-3-Methylglutaryl Coenzyme A Synthase Fusion Protein Responsible for Hirsutene Biosynthesis in Stereum hirsutum.

    Science.gov (United States)

    Flynn, Christopher M; Schmidt-Dannert, Claudia

    2018-06-01

    The wood-rotting mushroom Stereum hirsutum is a known producer of a large number of namesake hirsutenoids, many with important bioactivities. Hirsutenoids form a structurally diverse and distinct class of sesquiterpenoids. No genes involved in hirsutenoid biosynthesis have yet been identified or their enzymes characterized. Here, we describe the cloning and functional characterization of a hirsutene synthase as an unexpected fusion protein of a sesquiterpene synthase (STS) with a C-terminal 3-hydroxy-3-methylglutaryl-coenzyme A (3-hydroxy-3-methylglutaryl-CoA) synthase (HMGS) domain. Both the full-length fusion protein and truncated STS domain are highly product-specific 1,11-cyclizing STS enzymes with kinetic properties typical of STSs. Complementation studies in Saccharomyces cerevisiae confirmed that the HMGS domain is also functional in vivo Phylogenetic analysis shows that the hirsutene synthase domain does not form a clade with other previously characterized sesquiterpene synthases from Basidiomycota. Comparative gene structure analysis of this hirsutene synthase with characterized fungal enzymes reveals a significantly higher intron density, suggesting that this enzyme may be acquired by horizontal gene transfer. In contrast, the HMGS domain is clearly related to other fungal homologs. This STS-HMGS fusion protein is part of a biosynthetic gene cluster that includes P450s and oxidases that are expressed and could be cloned from cDNA. Finally, this unusual fusion of a terpene synthase to an HMGS domain, which is not generally recognized as a key regulatory enzyme of the mevalonate isoprenoid precursor pathway, led to the identification of additional HMGS duplications in many fungal genomes, including the localization of HMGSs in other predicted sesquiterpenoid biosynthetic gene clusters. IMPORTANCE Hirsutenoids represent a structurally diverse class of bioactive sesquiterpenoids isolated from fungi. Identification of their biosynthetic pathways will provide

  19. Impaired glycogen synthase activity and mitochondrial dysfunction in skeletal muscle

    DEFF Research Database (Denmark)

    Højlund, Kurt; Beck-Nielsen, Henning

    2006-01-01

    Insulin resistance in skeletal muscle is a major hallmark of type 2 diabetes and an early detectable abnormality in the development of this disease. The cellular mechanisms of insulin resistance include impaired insulin-mediated muscle glycogen synthesis and increased intramyocellular lipid content......, whereas impaired insulin activation of muscle glycogen synthase represents a consistent, molecular defect found in both type 2 diabetic and high-risk individuals. Despite several studies of the insulin signaling pathway believed to mediate dephosphorylation and hence activation of glycogen synthase......, the molecular mechanisms responsible for this defect remain unknown. Recently, the use of phospho-specific antibodies in human diabetic muscle has revealed hyperphosphorylation of glycogen synthase at sites not regulated by the classical insulin signaling pathway. In addition, novel approaches such as gene...

  20. Class II recombinant phosphoribosyl diphosphate synthase from spinach

    DEFF Research Database (Denmark)

    Krath, B N; Hove-Jensen, B

    2001-01-01

    to other PRPP synthases the activity of spinach PRPP synthase isozyme 3 is independent of P(i), and the enzyme is inhibited by ribonucleoside diphosphates in a purely competitive manner, which indicates a lack of allosteric inhibition by these compounds. In addition spinach PRPP synthase isozyme 3 shows...... an unusual low specificity toward diphosphoryl donors by accepting dATP, GTP, CTP, and UTP in addition to ATP. The kinetic mechanism of the enzyme is an ordered steady state Bi Bi mechanism with K(ATP) and K(Rib-5-P) values of 170 and 110 micrometer, respectively, and a V(max) value of 13.1 micromol (min x...... mg of protein)(-1). The enzyme has an absolute requirement for magnesium ions, and maximal activity is obtained at 40 degrees C at pH 7.6....

  1. Conductive Au nanowires regulated by silk fibroin nanofibers

    Science.gov (United States)

    Dong, Bo-Ju; Lu, Qiang

    2014-03-01

    Conductive Au-biopolymer composites have promising applications in tissue engineering such as nerve tissue regeneration. In this study, silk fibroin nanofibers were formed in aqueous solution by regulating silk self-assembly process and then used as template for Au nanowire fabrication. We performed the synthesis of Au seeds by repeating the seeding cycles for several times in order to increase the density of Au seeds on the nanofibers. After electroless plating, densely decorated Au seeds grew into irregularly shaped particles following silk nanofiber to fill the gaps between particles and finally form uniform continuous nanowires. The conductive property of the Au-silk fibroin nanowires was studied with current-voltage ( I-V) measurement. A typical ohmic behavior was observed, which highlighted their potential applications in nerve tissue regeneration.

  2. Conduction mechanism of nitronyl-nitroxide molecular magnetic compounds

    Science.gov (United States)

    Dotti, N.; Heintze, E.; Slota, M.; Hübner, R.; Wang, F.; Nuss, J.; Dressel, M.; Bogani, L.

    2016-04-01

    We investigate the conduction mechanisms of nitronyl-nitroxide (NIT) molecular radicals, as useful for the creation of nanoscopic molecular spintronic devices, finding that it does not correspond to standard Mott behavior, as previously postulated. We provide a complete investigation using transport measurements, low-energy, sub-THz spectroscopy and introducing differently substituted phenyl appendages. We show that a nontrivial surface-charge-limited regime is present in addition to the standard low-voltage Ohmic conductance. Scaling analysis allows one to determine all the main transport parameters for the compounds and highlights the presence of charge-trapping effects. Comparison among the different compounds shows the relevance of intermolecular stacking between the aromatic ring of the phenyl appendix and the NIT motif in the creation of useful electron transport channels. The importance of intermolecular pathways is further highlighted by electronic structure calculations, which clarify the nature of the electronic channels and their effect on the Mott character of the compounds.

  3. Structure and mechanism of the diterpene cyclase ent-copalyl diphosphate synthase

    Energy Technology Data Exchange (ETDEWEB)

    Köksal, Mustafa; Hu, Huayou; Coates, Robert M.; Peters, Reuben J.; Christianson, David W. (UIUC); (Iowa State); (Penn)

    2011-09-20

    The structure of ent-copalyl diphosphate synthase reveals three {alpha}-helical domains ({alpha}, {beta} and {gamma}), as also observed in the related diterpene cyclase taxadiene synthase. However, active sites are located at the interface of the {beta}{gamma} domains in ent-copalyl diphosphate synthase but exclusively in the {alpha} domain of taxadiene synthase. Modular domain architecture in plant diterpene cyclases enables the evolution of alternative active sites and chemical strategies for catalyzing isoprenoid cyclization reactions.

  4. Predicting the catalytic sites of isopenicillin N synthase (IPNS ...

    African Journals Online (AJOL)

    Isopenicillin N synthase (IPNS) related Non-haem iron-dependent oxygenases and oxidases (NHIDOX) demonstrated a striking structural conservativeness, even with low protein sequence homology. It is evident that these enzymes have an architecturally similar catalytic centre with active ligands lining the reactive pocket.

  5. Studies on the Active Site of Deacetoxycephalosporin C Synthase

    NARCIS (Netherlands)

    Lloyd, Matthew D.; Lee, Hwei-Jen; Harlos, Karl; Zhang, Zhi-Hong; Baldwin, Jack E.; Schofield, Christopher J.; Charnock, John M.; Garner, C. David; Hara, Takane; Terwisscha van Scheltinga, Anke C.; Valegård, Karin; Viklund, Jenny A.C.; Hajdu, Janos; Andersson, Inger; Danielsson, Åke; Bhikhabhai, Rama

    1999-01-01

    The Fe(II) and 2-oxoglutarate-dependent dioxygenase deacetoxycephalosporin C synthase (DAOCS) from Streptomyces clavuligerus was expressed at ca 25% of total soluble protein in Escherichia coli and purified by an efficient large-scale procedure. Purified protein catalysed the conversions of

  6. Beta-Glucan Synthase Gene Expression in Pleurotus sp

    International Nuclear Information System (INIS)

    Azhar Mohamad; Nie, H.J.

    2016-01-01

    Pleurotus sp. is a popular edible mushroom, containing various functional component, in particular, Beta-glucan. Beta-glucans is a part of glucan family of polysaccharides and supposedly contribute to medicinal and nutritional value of Pleurotus.sp. In order to understand the distribution of Beta-glucan in Pleurotus.sp, the Beta-glucan synthase gene expression was determined and compared in different part of Pleurotus, namely mycelium, stripe and cap. The Pleurotus.sp RNA was extracted using commercial kit, employing Tissuelyser ll (Qiagen, USA) to disrupt the cell walls. Then the RNA was quantified by Nano drop (Thermo Fisher, USA) and visualized using denaturing agarose gel. RNA with good OD 260.280 reading (∼2.0) was chosen and converted to cDNA. Using Laccase synthase gene as home keeping gene, Beta-glucan synthase gene expression was quantified using CFX 96 Real Time PCR detection system (Biorad, USA). Preliminary result shows that Beta-glucan synthase was relatively expressed the most in stripe, followed by mycelium and barely in cap. (author)

  7. Isolation and expression of the Pneumocystis carinii thymidylate synthase gene

    DEFF Research Database (Denmark)

    Edman, U; Edman, J C; Lundgren, B

    1989-01-01

    The thymidylate synthase (TS) gene from Pneumocystis carinii has been isolated from complementary and genomic DNA libraries and expressed in Escherichia coli. The coding sequence of TS is 891 nucleotides, encoding a 297-amino acid protein of Mr 34,269. The deduced amino acid sequence is similar...

  8. Insight into Biochemical Characterization of Plant Sesquiterpene Synthases

    DEFF Research Database (Denmark)

    Manczak, Tom; Simonsen, Henrik Toft

    2016-01-01

    A fast and reproducible protocol was established for enzymatic characterization of plant sesquiterpene synthases that can incorporate radioactivity in their products. The method utilizes the 96-well format in conjunction with cluster tubes and enables processing of >200 samples a day. Along...... with reduced reagent usage, it allows further reduction in the use of radioactive isotopes and flammable organic solvents. The sesquiterpene synthases previously characterized were expressed in yeast, and the plant-derived Thapsia garganica kunzeaol synthase TgTPS2 was tested in this method. KM for TgTPS2...... was found to be 0.55 μM; the turnover number, kcat, was found to be 0.29 s-1, kcat for TgTPS2 is in agreement with that of terpene synthases of other plants, and kcat/KM was found to be 0.53 s-1 μM-1 for TgTPS2. The kinetic parameters were in agreement with previously published data....

  9. Endothelial nitric oxide synthase polymorphism G298T in ...

    Indian Academy of Sciences (India)

    Supplementary data: Endothelial nitric oxide synthase polymorphism G298T in association with oxidative DNA damage in coronary atherosclerosis. Rajesh G. Kumar, Mrudula K. Spurthi, Kishore G. Kumar, Sanjib K. Sahu and Surekha H. Rani. J. Genet. 91, 349–352. Table 1. The demographic and clinical data of the CHD ...

  10. ATP synthase--a marvellous rotary engine of the cell.

    Science.gov (United States)

    Yoshida, M; Muneyuki, E; Hisabori, T

    2001-09-01

    ATP synthase can be thought of as a complex of two motors--the ATP-driven F1 motor and the proton-driven Fo motor--that rotate in opposite directions. The mechanisms by which rotation and catalysis are coupled in the working enzyme are now being unravelled on a molecular scale.

  11. Contribution of granule bound starch synthase in kernel modification ...

    African Journals Online (AJOL)

    The role of gbssI and gbssII genes, encoding granule bound starch synthase enzyme I and II, respectively, in quality protein maize (QPM) were studied at different days after pollination (DAP). Total RNA was used for first strand cDNA synthesis using the ImpromIISriptTM reverse transcriptase. No detectable levels of gbssI ...

  12. Dihydropteroate synthase gene mutations in Pneumocystis and sulfa resistance

    DEFF Research Database (Denmark)

    Huang, Laurence; Crothers, Kristina; Atzori, Chiara

    2004-01-01

    in the dihydropteroate synthase (DHPS) gene. Similar mutations have been observed in P. jirovecii. Studies have consistently demonstrated a significant association between the use of sulfa drugs for PCP prophylaxis and DHPS gene mutations. Whether these mutations confer resistance to TMP-SMX or dapsone plus trimethoprim...

  13. Analysis of genetic variation of inducible nitric oxide synthase and ...

    African Journals Online (AJOL)

    The genetic diversity of 100 Malaysian native chickens was investigated using polymerase chain reaction-restriction fragment polymorphism (PCR-RFLP) for two candidate genes: inducible nitric oxide synthase (INOS) and natural resistance-associated macrophage protein 1 (NRAMP1). The two genes were selected ...

  14. Characterising the cellulose synthase complexes of cell walls

    NARCIS (Netherlands)

    Mansoori Zangir, N.

    2012-01-01

    One of the characteristics of the plant kingdom is the presence of a structural cell wall. Cellulose is a major component in both the primary and secondary cell walls of plants. In higher plants cellulose is synthesized by so called rosette protein complexes with cellulose synthases (CESAs) as

  15. Molecular cloning and characterization of strictosidine synthase, a ...

    African Journals Online (AJOL)

    Mitragynine is one of the most dominant indole alkaloids present in the leaves of Mitragyna speciosa, a species of Rubiaceae. This alkaloid is believed to be synthesized via condensation of the amino acid derivative, tryptamine and secologanine by the action of strictosidine synthase (STR). The cDNA clone encoding STR ...

  16. Functional Characterization of Sesquiterpene Synthase from Polygonum minus

    Directory of Open Access Journals (Sweden)

    Su-Fang Ee

    2014-01-01

    Full Text Available Polygonum minus is an aromatic plant, which contains high abundance of terpenoids, especially the sesquiterpenes C15H24. Sesquiterpenes were believed to contribute to the many useful biological properties in plants. This study aimed to functionally characterize a full length sesquiterpene synthase gene from P. minus. P. minus sesquiterpene synthase (PmSTS has a complete open reading frame (ORF of 1689 base pairs encoding a 562 amino acid protein. Similar to other sesquiterpene synthases, PmSTS has two large domains: the N-terminal domain and the C-terminal metal-binding domain. It also consists of three conserved motifs: the DDXXD, NSE/DTE, and RXR. A three-dimensional protein model for PmSTS built clearly distinguished the two main domains, where conserved motifs were highlighted. We also constructed a phylogenetic tree, which showed that PmSTS belongs to the angiosperm sesquiterpene synthase subfamily Tps-a. To examine the function of PmSTS, we expressed this gene in Arabidopsis thaliana. Two transgenic lines, designated as OE3 and OE7, were further characterized, both molecularly and functionally. The transgenic plants demonstrated smaller basal rosette leaves, shorter and fewer flowering stems, and fewer seeds compared to wild type plants. Gas chromatography-mass spectrometry analysis of the transgenic plants showed that PmSTS was responsible for the production of β-sesquiphellandrene.

  17. The geranylgeranyl pyrophosphate synthase gene from Ginkgo ...

    African Journals Online (AJOL)

    STORAGESEVER

    2009-04-06

    Apr 6, 2009 ... Ginkgo biloba is one of the oldest living plant species and often referred to as “a .... GbGGDPS were analyzed and the sequence comparison was conducted ... function of plant GGDPS genes (Zhu et al., 1997) and human and.

  18. Identifying the catalytic components of cellulose synthase and the maize mixed-linkage beta-glucan synthase

    Energy Technology Data Exchange (ETDEWEB)

    Nicholas C Carpita

    2009-04-20

    Five specific objectives of this project are to develop strategies to identify the genes that encode the catalytic components of "mixed-linkage" (1→3),(1→4)-beta-D-glucans in grasses, to determine the protein components of the synthase complex, and determine the biochemical mechanism of synthesis. We have used proteomic approaches to define intrinsic and extrinsic polypeptides of Golgi membranes that are associated with polysaccharide synthesis and trafficking. We were successful in producing recombinant catalytic domains of cellulose synthase genes and discovered that they dimerize upon concentration, indicating that two CesA proteins form the catalytic unit. We characterized a brittle stalk2 mutant as a defect in a COBRA-like protein that results in compromised lignin-cellulose interactions that decrease tissue flexibility. We used virus-induced gene silencing of barley cell wall polysaccharide synthesis by BSMV in an attempt to silence specific members of the cellulose synthase-like gene family. However, we unexpectedly found that regardless of the specificity of the target gene, whole gene interaction networks were silenced. We discovered the cause to be an antisense transcript of the cellulose synthase gene initiated small interfering RNAs that spread silencing to related genes.

  19. Isolation and functional characterization of a τ-cadinol synthase, a new sesquiterpene synthase from Lavandula angustifolia.

    Science.gov (United States)

    Jullien, Frédéric; Moja, Sandrine; Bony, Aurélie; Legrand, Sylvain; Petit, Cécile; Benabdelkader, Tarek; Poirot, Kévin; Fiorucci, Sébastien; Guitton, Yann; Nicolè, Florence; Baudino, Sylvie; Magnard, Jean-Louis

    2014-01-01

    In this paper we characterize three sTPSs: a germacrene D (LaGERDS), a (E)-β-caryophyllene (LaCARS) and a τ-cadinol synthase (LaCADS). τ-cadinol synthase is reported here for the first time and its activity was studied in several biological models including transiently or stably transformed tobacco species. Three dimensional structure models of LaCADS and Ocimum basilicum γ-cadinene synthase were built by homology modeling using the template structure of Gossypium arboreum δ-cadinene synthase. The depiction of their active site organization provides evidence of the global influence of the enzymes on the formation of τ-cadinol: instead of a unique amino-acid, the electrostatic properties and solvent accessibility of the whole active site in LaCADS may explain the stabilization of the cadinyl cation intermediate. Quantitative PCR performed from leaves and inflorescences showed two patterns of expression. LaGERDS and LaCARS were mainly expressed during early stages of flower development and, at these stages, transcript levels paralleled the accumulation of the corresponding terpene products (germacrene D and (E)-β-caryophyllene). By contrast, the expression level of LaCADS was constant in leaves and flowers. Phylogenetic analysis provided informative results on potential duplication process leading to sTPS diversification in lavender.

  20. Isolation of Persicaria minor sesquiterpene synthase promoter and its deletions for transgenic Arabidopsis thaliana

    Science.gov (United States)

    Omar, Aimi Farehah; Ismail, Ismanizan

    2016-11-01

    Sesquiterpene synthase (SS) catalyzes the formation of sesquiterpenes from farnesyl diphosphate (FDP) via carbocation intermediates. In this study, the promoter region of sesquiterpene synthase was isolated from Persicaria minor to identify possible cis-acting elements in the promoter. The full-length PmSS promoter of P. minor is 1824-bp sequences. The sequence was analyzed and several putative cis-acting regulatory elements were identified. Three cis-acting regulatory elements were selected for deletion analysis which are cis-acting element involved in wound responsiveness (WUN), cis - acting element involved in defense and stress responsiveness (TC) and cis-acting element involved in ABA responsiveness (ABRE). Series of deletions were conducted to assess the promoter activity producing three truncated fragments promoter; Prom 2 1606-bp, Prom 3 1144- bp, and Prom 4 921-bp. The full-length promoter and its deletion series were cloned into the pBGWFS7 vector which contain β-glucuronidase (GUS) gene and green fluorescent protein (GFP) as the reporter gene. All constructs were successfully transformed into Arabidopsis thaliana based on PCR of positive BASTA resistance plants.

  1. Evolutionary and mechanistic insights from the reconstruction of α-humulene synthases from a modern (+)-germacrene A synthase.

    Science.gov (United States)

    Gonzalez, Veronica; Touchet, Sabrina; Grundy, Daniel J; Faraldos, Juan A; Allemann, Rudolf K

    2014-10-15

    Germacrene A synthase (GAS) from Solidago canadensis catalyzes the conversion of farnesyl diphosphate (FDP) to the plant sesquiterpene (+)-germacrene A. After diphosphate expulsion, farnesyl cation reacts with the distal 10,11-double bond to afford germacrene A (>96%) and <2% α-humulene, which arises from 1,11-cyclization of FDP. The origin of the 1,11-activity of GAS was investigated by amino acid sequence alignments of 1,10- and 1,11-synthases and comparisons of X-ray crystal structures with the homology model of GAS; a triad [Thr 401-Gly 402-Gly 403] that might be responsible for the predominant 1,10-cyclization activity of GAS was identified. Replacement of Gly 402 with residues of increasing size led to a progressive increase of 1,11-cyclization. The catalytic robustness of these 1,10- /1,11-GAS variants point to Gly 402 as a functional switch of evolutionary significance and suggests that enzymes with strict functionalities have evolved from less specific ancestors through a small number of substitutions. Similar results were obtained with germacrene D synthase (GDS) upon replacement of the homologous active-site residue Gly 404: GDS-G404V generated approximately 20% bicyclogermacrene, a hydrocarbon with a cyclopropane ring that underlines the dual 1,10-/1,11-cyclization activity of this mutant. This suggests that the reaction pathways to germacrenes and humulenes might be connected through a bridged 1,10,11-carbocation intermediate or transition state that resembles bicyclogermacrene. Mechanistic studies using [1-(3)H1]-10-fluorofarnesyl diphosphate and deuterium-labeling experiments with [12,13-(2)H6]-FDP support a germacrene-humulene rearrangement linking 1,10- and 1,11-pathways. These results support the bioinformatics proposal that modern 1,10-synthases could have evolved from promiscuous 1,11-sesquiterpene synthases.

  2. Coexistence and competition of surface diffusion and geometric shielding in the growth of 1D bismuth nanostructures and their ohmic contact

    International Nuclear Information System (INIS)

    Tian, Ye; Jiang, Lianjun; Zhang, Xuejun; Deng, Yangbao; Deng, Shuguang

    2014-01-01

    We study the physical-vapor-deposition of 1D bismuth nanostructures. Bi nanowire elongating along [012] and/or [110] direction as well as anisotropic Bi nano-columns are physical-vapor-deposited successfully. The coexistence and competition of surface diffusion and geometric shielding are critical to their formation as well as growth mode transition among them. Since physical-vapor-deposition is a vacuum process, we make use of it to fabricate the ohmic contact to prevent the damage to the bismuth nanostructures brought by the etching to their thick surface oxide layer. (paper)

  3. Role of Ag-alloy in the thermal stability of Ag-based ohmic contact to GaN(0 0 0 1) surface

    International Nuclear Information System (INIS)

    Xiong, Zhihua; Qin, Zhenzhen; Zhao, Qian; Chen, Lanli

    2015-01-01

    First-principles calculations are performed to study Ag and Ag-alloy adsorption stability on GaN(0 0 0 1) surface. We find Ag only contact to GaN surface is unstable under high temperature. While Ag-alloy adsorption exhibits better adsorption stability and electronic properties than that of the Ag only contact,due to the enhanced interaction between Ag-alloy and GaN(0 0 0 1) surface. The Ag-alloy, particularly AgNi, is proposed to be used as very promising ohmic contact to GaN for practical applications

  4. Incompressible Steady Flow with Tensor Conductivity Leaving a Transverse Magnetic Field

    International Nuclear Information System (INIS)

    Witalis, E.A.

    1965-12-01

    The straight channel flow of an inviscid, incompressible fluid with tensor conductivity is considered when the flow leaves a region of constant transverse magnetic field. The channel walls are taken to be insulating, and an eddy current system arises. This is investigated by the method of magnetic field analysis as given by Witalis. The spatial distribution of magnetic field and ohmic power loss, both parallel and transverse to the flow, are given as functions of the Hall parameter with consideration also to the magnetic Reynolds number of the fluid. MHD power generator aspects of this problem and the results are discussed

  5. Incompressible Steady Flow with Tensor Conductivity Leaving a Transverse Magnetic Field

    Energy Technology Data Exchange (ETDEWEB)

    Witalis, E A

    1965-12-15

    The straight channel flow of an inviscid, incompressible fluid with tensor conductivity is considered when the flow leaves a region of constant transverse magnetic field. The channel walls are taken to be insulating, and an eddy current system arises. This is investigated by the method of magnetic field analysis as given by Witalis. The spatial distribution of magnetic field and ohmic power loss, both parallel and transverse to the flow, are given as functions of the Hall parameter with consideration also to the magnetic Reynolds number of the fluid. MHD power generator aspects of this problem and the results are discussed.

  6. In vitro biochemical characterization of all barley endosperm starch synthases

    DEFF Research Database (Denmark)

    Cuesta-Seijo, Jose A.; Nielsen, Morten M.; Ruzanski, Christian

    2016-01-01

    Starch is the main storage polysaccharide in cereals and the major source of calories in the human diet. It is synthesized by a panel of enzymes including five classes of starch synthases (SSs). While the overall starch synthase (SS) reaction is known, the functional differences between the five SS....... Here we provide a detailed biochemical study of the activity of all five classes of SSs in barley endosperm. Each enzyme was produced recombinantly in E. coli and the properties and modes of action in vitro were studied in isolation from other SSs and other substrate modifying activities. Our results...... define the mode of action of each SS class in unprecedented detail; we analyze their substrate selection, temperature dependence and stability, substrate affinity and temporal abundance during barley development. Our results are at variance with some generally accepted ideas about starch biosynthesis...

  7. ATP Synthase, a Target for Dementia and Aging?

    Science.gov (United States)

    Larrick, James W; Larrick, Jasmine W; Mendelsohn, Andrew R

    2018-02-01

    Advancing age is the biggest risk factor for development for the major life-threatening diseases in industrialized nations accounting for >90% of deaths. Alzheimer's dementia (AD) is among the most devastating. Currently approved therapies fail to slow progression of the disease, providing only modest improvements in memory. Recently reported work describes mechanistic studies of J147, a promising therapeutic molecule previously shown to rescue the severe cognitive deficits exhibited by aged, transgenic AD mice. Apparently, J147 targets the mitochondrial alpha-F1-ATP synthase (ATP5A). Modest inhibition of the ATP synthase modulates intracellular calcium to activate AMP-activated protein kinase to inhibit mammalian target of rapamycin, a known mechanism of lifespan extension from worms to mammals.

  8. Isolation and characterization of terpene synthases in cotton (Gossypium hirsutum).

    Science.gov (United States)

    Yang, Chang-Qing; Wu, Xiu-Ming; Ruan, Ju-Xin; Hu, Wen-Li; Mao, Yin-Bo; Chen, Xiao-Ya; Wang, Ling-Jian

    2013-12-01

    Cotton plants accumulate gossypol and related sesquiterpene aldehydes, which function as phytoalexins against pathogens and feeding deterrents to herbivorous insects. However, to date little is known about the biosynthesis of volatile terpenes in this crop. Herein is reported that 5 monoterpenes and 11 sesquiterpenes from extracts of a glanded cotton cultivar, Gossypium hirsutum cv. CCRI12, were detected by gas chromatography-mass spectrometry (GC-MS). By EST data mining combined with Rapid Amplification of cDNA Ends (RACE), full-length cDNAs of three terpene synthases (TPSs), GhTPS1, GhTPS2 and GhTPS3 were isolated. By in vitro assays of the recombinant proteins, it was found that GhTPS1 and GhTPS2 are sesquiterpene synthases: the former converted farnesyl pyrophosphate (FPP) into β-caryophyllene and α-humulene in a ratio of 2:1, whereas the latter produced several sesquiterpenes with guaia-1(10),11-diene as the major product. By contrast, GhTPS3 is a monoterpene synthase, which produced α-pinene, β-pinene, β-phellandrene and trace amounts of other monoterpenes from geranyl pyrophosphate (GPP). The TPS activities were also supported by Virus Induced Gene Silencing (VIGS) in the cotton plant. GhTPS1 and GhTPS3 were highly expressed in the cotton plant overall, whereas GhTPS2 was expressed only in leaves. When stimulated by mechanical wounding, Verticillium dahliae (Vde) elicitor or methyl jasmonate (MeJA), production of terpenes and expression of the corresponding synthase genes were induced. These data demonstrate that the three genes account for the biosynthesis of volatile terpenes of cotton, at least of this Upland cotton. Copyright © 2013 Elsevier Ltd. All rights reserved.

  9. Nitric oxide synthase isoforms in spontaneous and salt hypertension

    Czech Academy of Sciences Publication Activity Database

    Hojná, Silvie; Kuneš, Jaroslav; Zicha, Josef

    2007-01-01

    Roč. 25, Suppl. 2 (2007), S 338-S 338 ISSN 0263-6352. [European Meeting on Hypertension /17./. 15.06.2007-19.06.2007, Milan] R&D Projects: GA MŠk(CZ) 1M0510 Institutional research plan: CEZ:AV0Z50110509 Keywords : nitric oxide synthase isoforms * spontaneous and salt hypertension Subject RIV: FA - Cardiovascular Diseases incl. Cardiotharic Surgery

  10. Use of linalool synthase in genetic engineering of scent production

    Science.gov (United States)

    Pichersky, Eran

    1998-01-01

    A purified S-linalool synthase polypeptide from Clarkia breweri is disclosed as is the recombinant polypeptide and nucleic acid sequences encoding the polypeptide. Also disclosed are antibodies immunoreactive with the purified peptide and with recombinant versions of the polypeptide. Methods of using the nucleic acid sequences, as well as methods of enhancing the smell and the flavor of plants expressing the nucleic acid sequences are also disclosed.

  11. Trypanosoma brucei solanesyl-diphosphate synthase localizes to the mitochondrion

    Czech Academy of Sciences Publication Activity Database

    Lai, D.-H.; Bontempi, E. J.; Lukeš, Julius

    2012-01-01

    Roč. 183, č. 2 (2012), s. 189-192 ISSN 0166-6851 R&D Projects: GA ČR(CZ) GAP305/11/2179 Institutional support: RVO:60077344 Keywords : Trypanosoma brucei * Sleeping sickness * Ubiquinone * Solanesyl-diphosphate synthase * Digitonin permeabilization * In situ tagging Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 2.734, year: 2012 http://www.sciencedirect.com/science/article/pii/S0166685112000539

  12. Multi-substrate terpene synthases: their occurrence and physiological significance

    Directory of Open Access Journals (Sweden)

    Leila Pazouki

    2016-07-01

    Full Text Available Terpene synthases are responsible for synthesis of a large number of terpenes in plants using substrates provided by two distinct metabolic pathways, the mevalonate-dependent pathway that is located in cytosol and has been suggested to be responsible for synthesis of sesquiterpenes (C15, and 2-C-methyl-D-erythritol-4-phosphate pathway located in plastids and suggested to be responsible for the synthesis of hemi- (C5, mono- (C10 and diterpenes (C20. Recent advances in characterization of genes and enzymes responsible for substrate and end product biosynthesis as well as efforts in metabolic engineering have demonstrated existence of a number of multi-substrate terpene synthases. This review summarizes the progress in the characterization of such multi-substrate terpene synthases and suggests that the presence of multi-substrate use might have been significantly underestimated. Multi-substrate use could lead to important changes in terpene product profiles upon substrate profile changes under perturbation of metabolism in stressed plants as well as under certain developmental stages. We therefore argue that multi-substrate use can be significant under physiological conditions and can result in complicate modifications in terpene profiles.

  13. From bacterial to human dihydrouridine synthase: automated structure determination

    Energy Technology Data Exchange (ETDEWEB)

    Whelan, Fiona, E-mail: fiona.whelan@york.ac.uk; Jenkins, Huw T., E-mail: fiona.whelan@york.ac.uk [The University of York, Heslington, York YO10 5DD (United Kingdom); Griffiths, Samuel C. [University of Oxford, Headington, Oxford OX3 7BN (United Kingdom); Byrne, Robert T. [Ludwig-Maximilians-University Munich, Feodor-Lynen-Strasse 25, 81377 Munich (Germany); Dodson, Eleanor J.; Antson, Alfred A., E-mail: fiona.whelan@york.ac.uk [The University of York, Heslington, York YO10 5DD (United Kingdom)

    2015-06-30

    The crystal structure of a human dihydrouridine synthase, an enzyme associated with lung cancer, with 18% sequence identity to a T. maritima enzyme, has been determined at 1.9 Å resolution by molecular replacement after extensive molecular remodelling of the template. The reduction of uridine to dihydrouridine at specific positions in tRNA is catalysed by dihydrouridine synthase (Dus) enzymes. Increased expression of human dihydrouridine synthase 2 (hDus2) has been linked to pulmonary carcinogenesis, while its knockdown decreased cancer cell line viability, suggesting that it may serve as a valuable target for therapeutic intervention. Here, the X-ray crystal structure of a construct of hDus2 encompassing the catalytic and tRNA-recognition domains (residues 1–340) determined at 1.9 Å resolution is presented. It is shown that the structure can be determined automatically by phenix.mr-rosetta starting from a bacterial Dus enzyme with only 18% sequence identity and a significantly divergent structure. The overall fold of the human Dus2 is similar to that of bacterial enzymes, but has a larger recognition domain and a unique three-stranded antiparallel β-sheet insertion into the catalytic domain that packs next to the recognition domain, contributing to domain–domain interactions. The structure may inform the development of novel therapeutic approaches in the fight against lung cancer.

  14. From bacterial to human dihydrouridine synthase: automated structure determination

    International Nuclear Information System (INIS)

    Whelan, Fiona; Jenkins, Huw T.; Griffiths, Samuel C.; Byrne, Robert T.; Dodson, Eleanor J.; Antson, Alfred A.

    2015-01-01

    The crystal structure of a human dihydrouridine synthase, an enzyme associated with lung cancer, with 18% sequence identity to a T. maritima enzyme, has been determined at 1.9 Å resolution by molecular replacement after extensive molecular remodelling of the template. The reduction of uridine to dihydrouridine at specific positions in tRNA is catalysed by dihydrouridine synthase (Dus) enzymes. Increased expression of human dihydrouridine synthase 2 (hDus2) has been linked to pulmonary carcinogenesis, while its knockdown decreased cancer cell line viability, suggesting that it may serve as a valuable target for therapeutic intervention. Here, the X-ray crystal structure of a construct of hDus2 encompassing the catalytic and tRNA-recognition domains (residues 1–340) determined at 1.9 Å resolution is presented. It is shown that the structure can be determined automatically by phenix.mr-rosetta starting from a bacterial Dus enzyme with only 18% sequence identity and a significantly divergent structure. The overall fold of the human Dus2 is similar to that of bacterial enzymes, but has a larger recognition domain and a unique three-stranded antiparallel β-sheet insertion into the catalytic domain that packs next to the recognition domain, contributing to domain–domain interactions. The structure may inform the development of novel therapeutic approaches in the fight against lung cancer

  15. Dynamics of meso and thermo citrate synthases with implicit solvation

    Science.gov (United States)

    Cordeiro, J. M. M.

    The dynamics of hydration of meso and thermo citrate synthases has been investigated using the EEF1 methodology implemented with the CHARMM program. The native enzymes are composed of two identical subunits, each divided into a small and large domain. The dynamics behavior of both enzymes at 30°C and 60°C has been compared. The results of simulations show that during the hydration process, each subunit follows a different pathway of hydration, in spite of the identical sequence. The hydrated structures were compared with the crystalline structure, and the root mean square deviation (RMSD) of each residue along the trajectory was calculated. The regions with larger and smaller mobility were identified. In particular, helices belonging to the small domain are more mobile than those of the large domain. In contrast, the residues that constitute the active site show a much lower displacement compared with the crystalline structure. Hydration free energy calculations point out that Thermoplasma acidophilum citrate synthase (TCS) is more stable than chicken citrate synthase (CCS), at high temperatures. Such result has been ascribed to the higher number of superficial charges in the thermophilic homologue, which stabilizes the enzyme, while the mesophilic homologue denatures. These results are in accord with the experimental found that TCS keeps activity at temperatures farther apart from the catalysis regular temperature than the CCS.

  16. Mechanism of Action and Inhibition of dehydrosqualene Synthase

    Energy Technology Data Exchange (ETDEWEB)

    F Lin; C Liu; Y Liu; Y Zhang; K Wang; W Jeng; T Ko; R Cao; A Wang; E Oldfield

    2011-12-31

    'Head-to-head' terpene synthases catalyze the first committed steps in sterol and carotenoid biosynthesis: the condensation of two isoprenoid diphosphates to form cyclopropylcarbinyl diphosphates, followed by ring opening. Here, we report the structures of Staphylococcus aureus dehydrosqualene synthase (CrtM) complexed with its reaction intermediate, presqualene diphosphate (PSPP), the dehydrosqualene (DHS) product, as well as a series of inhibitors. The results indicate that, on initial diphosphate loss, the primary carbocation so formed bends down into the interior of the protein to react with C2,3 double bond in the prenyl acceptor to form PSPP, with the lower two-thirds of both PSPP chains occupying essentially the same positions as found in the two farnesyl chains in the substrates. The second-half reaction is then initiated by the PSPP diphosphate returning back to the Mg{sup 2+} cluster for ionization, with the resultant DHS so formed being trapped in a surface pocket. This mechanism is supported by the observation that cationic inhibitors (of interest as antiinfectives) bind with their positive charge located in the same region as the cyclopropyl carbinyl group; that S-thiolo-diphosphates only inhibit when in the allylic site; activity results on 11 mutants show that both DXXXD conserved domains are essential for PSPP ionization; and the observation that head-to-tail isoprenoid synthases as well as terpene cyclases have ionization and alkene-donor sites which spatially overlap those found in CrtM.

  17. Phytochelatin synthase activity as a marker of metal pollution

    Energy Technology Data Exchange (ETDEWEB)

    Zitka, Ondrej; Krystofova, Olga; Sobrova, Pavlina [Department of Chemistry and Biochemistry, Faculty of Agronomy, Mendel University in Brno, Zemedelska 1, CZ-613 00 Brno (Czech Republic); Adam, Vojtech [Department of Chemistry and Biochemistry, Faculty of Agronomy, Mendel University in Brno, Zemedelska 1, CZ-613 00 Brno (Czech Republic); Central European Institute of Technology, Brno University of Technology, Technicka 3058/10, CZ-616 00 Brno (Czech Republic); Zehnalek, Josef; Beklova, Miroslava [Department of Chemistry and Biochemistry, Faculty of Agronomy, Mendel University in Brno, Zemedelska 1, CZ-613 00 Brno (Czech Republic); Kizek, Rene, E-mail: kizek@sci.muni.cz [Department of Chemistry and Biochemistry, Faculty of Agronomy, Mendel University in Brno, Zemedelska 1, CZ-613 00 Brno (Czech Republic); Central European Institute of Technology, Brno University of Technology, Technicka 3058/10, CZ-616 00 Brno (Czech Republic)

    2011-08-30

    Highlights: {yields} New tool for determination of phytochelatin synthase activity. {yields} The optimization of experimental condition for determination of the enzyme activity. {yields} First evaluation of K{sub m} for the enzyme. {yields} The effects of cadmium (II) not only on the activity of the enzyme but also on K{sub m}. -- Abstract: The synthesis of phytochelatins is catalyzed by {gamma}-Glu-Cys dipeptidyl transpeptidase called phytochelatin synthase (PCS). Aim of this study was to suggest a new tool for determination of phytochelatin synthase activity in the tobacco BY-2 cells treated with different concentrations of the Cd(II). After the optimization steps, an experiment on BY-2 cells exposed to different concentrations of Cd(NO{sub 3}){sub 2} for 3 days was performed. At the end of the experiment, cells were harvested and homogenized. Reduced glutathione and cadmium (II) ions were added to the cell suspension supernatant. These mixtures were incubated at 35 {sup o}C for 30 min and analysed using high performance liquid chromatography coupled with electrochemical detector (HPLC-ED). The results revealed that PCS activity rises markedly with increasing concentration of cadmium (II) ions. The lowest concentration of the toxic metal ions caused almost three fold increase in PCS activity as compared to control samples. The activity of PCS (270 fkat) in treated cells was more than seven times higher in comparison to control ones. K{sub m} for PCS was estimated as 2.3 mM.

  18. Phytochelatin synthase activity as a marker of metal pollution

    International Nuclear Information System (INIS)

    Zitka, Ondrej; Krystofova, Olga; Sobrova, Pavlina; Adam, Vojtech; Zehnalek, Josef; Beklova, Miroslava; Kizek, Rene

    2011-01-01

    Highlights: → New tool for determination of phytochelatin synthase activity. → The optimization of experimental condition for determination of the enzyme activity. → First evaluation of K m for the enzyme. → The effects of cadmium (II) not only on the activity of the enzyme but also on K m . -- Abstract: The synthesis of phytochelatins is catalyzed by γ-Glu-Cys dipeptidyl transpeptidase called phytochelatin synthase (PCS). Aim of this study was to suggest a new tool for determination of phytochelatin synthase activity in the tobacco BY-2 cells treated with different concentrations of the Cd(II). After the optimization steps, an experiment on BY-2 cells exposed to different concentrations of Cd(NO 3 ) 2 for 3 days was performed. At the end of the experiment, cells were harvested and homogenized. Reduced glutathione and cadmium (II) ions were added to the cell suspension supernatant. These mixtures were incubated at 35 o C for 30 min and analysed using high performance liquid chromatography coupled with electrochemical detector (HPLC-ED). The results revealed that PCS activity rises markedly with increasing concentration of cadmium (II) ions. The lowest concentration of the toxic metal ions caused almost three fold increase in PCS activity as compared to control samples. The activity of PCS (270 fkat) in treated cells was more than seven times higher in comparison to control ones. K m for PCS was estimated as 2.3 mM.

  19. Longevity in vivo of primary cell wall cellulose synthases.

    Science.gov (United States)

    Hill, Joseph Lee; Josephs, Cooper; Barnes, William J; Anderson, Charles T; Tien, Ming

    2018-02-01

    Our work focuses on understanding the lifetime and thus stability of the three main cellulose synthase (CESA) proteins involved in primary cell wall synthesis of Arabidopsis. It had long been thought that a major means of CESA regulation was via their rapid degradation. However, our studies here have uncovered that AtCESA proteins are not rapidly degraded. Rather, they persist for an extended time in the plant cell. Plant cellulose is synthesized by membrane-embedded cellulose synthase complexes (CSCs). The CSC is composed of cellulose synthases (CESAs), of which three distinct isozymes form the primary cell wall CSC and another set of three isozymes form the secondary cell wall CSC. We determined the stability over time of primary cell wall (PCW) CESAs in Arabidopsis thaliana seedlings, using immunoblotting after inhibiting protein synthesis with cycloheximide treatment. Our work reveals very slow turnover for the Arabidopsis PCW CESAs in vivo. Additionally, we show that the stability of all three CESAs within the PCW CSC is altered by mutations in individual CESAs, elevated temperature, and light conditions. Together, these results suggest that CESA proteins are very stable in vivo, but that their lifetimes can be modulated by intrinsic and environmental cues.

  20. The primary defect in glycogen synthase activity is not based on increased glycogen synthase kinase-3a activity in diabetic myotubes

    DEFF Research Database (Denmark)

    Gaster, Michael; Brusgaard, Klaus; Handberg, Aa.

    2004-01-01

    The mechanism responsible for the diminished activation of glycogen synthase (GS) in diabetic myotubes remains unclear, but may involve increased activity and/or expression of glycogen synthase kinase-3 (GSK-3). In myotubes established from type 2 diabetic and healthy control subjects we determined...

  1. Conductivity in one-dimensional disordered Cs2TCNQ3 salts

    International Nuclear Information System (INIS)

    Messaoudi, M.; Duran, J.

    1984-01-01

    Room temperature, low frequency conductivity measurements of two isomers (I and II) of the Cs 2 TCNQ 3 compounds are made. The conductivity-voltage characteristic display informative data concerning the interaction between disorder and conductivity in these materials. The isomer I clearly exhibits a disorder-dominated conductivity as can be seen from deviations to the Ohmic law. The isomer II, on the contrary, shows up various features connected with the existence of stopping barriers. In particular, it is shown that the interdimensional crossover which takes place at low frequency plays a significant role in these experiments. Moreover the conductivity-voltage characteristic measured along the a axis (perpendicular to the stacking axis) displays a very interesting behavior whereby the disorder properties interplay in an unusual manner. (author)

  2. Enhancement of electrical conductivity of ion-implanted polymer films

    International Nuclear Information System (INIS)

    Brock, S.

    1985-01-01

    The electrical conductivity of ion-implanted films of Nylon 66, Polypropylene (PP), Poly(tetrafluoroethylene) (Teflon) and mainly Poly (ethylene terephthalate) (PET) was determined by DC measurements at voltages up to 4500 V and compared with the corresponding values of pristine films. Measurements were made at 21 0 C +/- 1 0 C and 65 +/- 2% RH. The electrical conductivity of PET films implanted with F + , Ar + , or As + ions at energies of 50 keV increases by seven orders of magnitude as the fluence increases from 1 x 10 18 to 1 x 10 20 ions/m 2 . The conductivity of films implanted with As + was approximately one order greater than those implanted with Ar + , which in turn was approximately one-half order greater than those implanted with F + . The conductivity of the most conductive film ∼1 S/m) was almost 14 orders of magnitude greater than the pristine PET film. Except for the three PET samples implanted at fluences near 1 x 10 20 ions/m 2 with F + , Ar + , and As + ions, all implanted films were ohmic up to an electric field strength of 600 kV/m. The temperature dependence of the conductivity of the three PET films implanted near a fluence of 1 x 10 20 ions/m 2 was measured over the range of 80 K < T < 300 K

  3. Synthesis and characterization of electrical conducting nanoporous carbon structures

    International Nuclear Information System (INIS)

    El Mir, L.; Kraiem, S.; Bengagi, M.; Elaloui, E.; Ouederni, A.; Alaya, S.

    2007-01-01

    Nanoporous organic xerogel compounds were prepared by sol-gel method from pyrogallol-formaldehyde (PF) mixtures in water using perchloric acid as catalyst. The preparation conditions of electrical conducting carbon (ECC) structures were explored by changing the pyrolysis temperature. The effect of this preparation parameters on the structural and electrical properties of the obtained ECCs were studied, respectively, by thermogravimetric analysis (TGA), nitrogen adsorption isotherms, IR spectroscopy and electrical conductivity measurements. The analysis of the obtained results revealed that, the polymeric insulating phase was transformed progressively with pyrolysis temperature into carbon conducting phase; this means the formation of long continuous conducting path for charge carriers when the carbon microparticles inside the structure agglomerated with thermal treatment and the samples exhibited tangible percolation behaviour where the percolation threshold can be determined by pyrolysis temperature. The temperature-dependent conductivity and the I(V) characteristics of the obtained ECC structures show a non-ohmic behaviour. The results obtained from TGA and differential thermal analyser (DTA) thermograms, scanning electron microscope (SEM) and transmission electron microscope (TEM) micrographs, IR spectroscopy and X-ray diffraction revealed that, the obtained ECC structures consist of amorphous and nanoporous electrical conducting carbon materials

  4. On a two-layer Si{sub 3}N{sub 4}/SiO{sub 2} dielectric mask for low-resistance ohmic contacts to AlGaN/GaN HEMTs

    Energy Technology Data Exchange (ETDEWEB)

    Arutyunyan, S. S., E-mail: spartakmain@gmail.com; Pavlov, A. Yu.; Pavlov, B. Yu.; Tomosh, K. N.; Fedorov, Yu. V. [Russian Academy of Sciences, Institute of Ultrahigh Frequency Semiconductor Electronics (Russian Federation)

    2016-08-15

    The fabrication of a two-layer Si{sub 3}N{sub 4}/SiO{sub 2} dielectric mask and features of its application in the technology of non-fired epitaxially grown ohmic contacts for high-power HEMTs on AlGaN/GaN heterostructures are described. The proposed Si{sub 3}N{sub 4}/SiO{sub 2} mask allows the selective epitaxial growth of heavily doped ohmic contacts by nitride molecular-beam epitaxy and the fabrication of non-fired ohmic contacts with a resistance of 0.15–0.2 Ω mm and a smooth surface and edge morphology.

  5. The Improvement of Electrical Characteristics of Pt/Ti Ohmic Contacts to Ga-Doped ZnO by Homogenized KrF Pulsed Excimer Laser Treatment

    Science.gov (United States)

    Oh, Min-Suk

    2018-04-01

    We investigated the effect of KrF excimer laser surface treatment on Pt/Ti ohmic contacts to Ga-doped n-ZnO ( N d = 4.3 × 1017 cm-3). The treatment of the n-ZnO surfaces by laser irradiation greatly improved the electrical characteristics of the metal contacts. The Pt/Ti ohmic layer on the laser-irradiated n-ZnO showed specific contact resistances of 2.5 × 10-4 ˜ 4.8 × 10-4 Ω cm2 depending on the laser energy density and gas ambient, which were about two orders of magnitude lower than that of the as-grown sample, 8.4 × 10-2 Ω cm2. X-ray photoelectron spectroscopy and photoluminescence measurements showed that the KrF excimer laser treatments increased the electron concentration near the surface region of the Ga-doped n-ZnO due to the preferential evaporation of oxygen atoms from the ZnO surface by the laser-induced dissociation of Zn-O bonds.

  6. Correlation between the electrical properties and the interfacial microstructures of TiAl-based ohmic contacts to p-type 4H-SiC

    Science.gov (United States)

    Tsukimoto, S.; Nitta, K.; Sakai, T.; Moriyama, M.; Murakami, Masanori

    2004-05-01

    In order to understand a mechanism of TiAl-based ohmic contact formation for p-type 4H-SiC, the electrical properties and microstructures of Ti/Al and Ni/Ti/Al contacts, which provided the specific contact resistances of approximately 2×10-5 Ω-cm2 and 7×10-5 Ω-cm2 after annealing at 1000°C and 800°C, respectively, were investigated using x-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). Ternary Ti3SiC2 carbide layers were observed to grow on the SiC surfaces in both the Ti/Al and the Ni/Ti/Al contacts when the contacts yielded low resistance. The Ti3SiC2 carbide layers with hexagonal structures had an epitaxial orientation relationship with the 4H-SiC substrates. The (0001)-oriented terraces were observed periodically at the interfaces between the carbide layers and the SiC, and the terraces were atomically flat. We believed the Ti3SiC2 carbide layers primarily reduced the high Schottky barrier height at the contact metal/p-SiC interface down to about 0.3 eV, and, thus, low contact resistances were obtained for p-type TiAl-based ohmic contacts.

  7. Influence of lateral and in-depth metal segregation on the patterning of ohmic contacts for GaN-based devices

    International Nuclear Information System (INIS)

    Redondo-Cubero, A; Alves, L C; Corregidor, V; Vázquez, L; Romero, M F; Muñoz, E; Pantellini, A; Lanzieri, C

    2014-01-01

    The lateral and in-depth metal segregation of Au/Ni/Al/Ti ohmic contacts for GaN-based high electron mobility transistors were analysed as a function of the Al barrier's thickness (d). The surface of the contacts, characterized by atomic force and scanning electron microscopy, shows a transition from a fractal network of rough and complex island-like structures towards smoother and cauliflower-like fronts with increasing d. Rutherford backscattering spectrometry and energy dispersive x-ray spectroscopy (EDXS) at different energies were used to confirm the in-depth intermixing of the metals relevant for the final contact resistance. EDXS mapping reveals a significant lateral segregation too, where the resulting patterns depend on two competing NiAl x and AuAl x phases, the intermixing being controlled by the available amount of Al. The optimum ohmic resistance is not affected by the patterning process, but is mainly dependent on the partial interdiffusion of the metals. (paper)

  8. Suites of Terpene Synthases Explain Differential Terpenoid Production in Ginger and Turmeric Tissues

    Science.gov (United States)

    Koo, Hyun Jo; Gang, David R.

    2012-01-01

    The essential oils of ginger (Zingiber officinale) and turmeric (Curcuma longa) contain a large variety of terpenoids, some of which possess anticancer, antiulcer, and antioxidant properties. Despite their importance, only four terpene synthases have been identified from the Zingiberaceae family: (+)-germacrene D synthase and (S)-β-bisabolene synthase from ginger rhizome, and α-humulene synthase and β-eudesmol synthase from shampoo ginger (Zingiber zerumbet) rhizome. We report the identification of 25 mono- and 18 sesquiterpene synthases from ginger and turmeric, with 13 and 11, respectively, being functionally characterized. Novel terpene synthases, (−)-caryolan-1-ol synthase and α-zingiberene/β-sesquiphellandrene synthase, which is responsible for formation of the major sesquiterpenoids in ginger and turmeric rhizomes, were also discovered. These suites of enzymes are responsible for formation of the majority of the terpenoids present in these two plants. Structures of several were modeled, and a comparison of sets of paralogs suggests how the terpene synthases in ginger and turmeric evolved. The most abundant and most important sesquiterpenoids in turmeric rhizomes, (+)-α-turmerone and (+)-β-turmerone, are produced from (−)-α-zingiberene and (−)-β-sesquiphellandrene, respectively, via α-zingiberene/β-sesquiphellandrene oxidase and a still unidentified dehydrogenase. PMID:23272109

  9. [BIOINFORMATIC SEARCH AND PHYLOGENETIC ANALYSIS OF THE CELLULOSE SYNTHASE GENES OF FLAX (LINUM USITATISSIMUM)].

    Science.gov (United States)

    Pydiura, N A; Bayer, G Ya; Galinousky, D V; Yemets, A I; Pirko, Ya V; Podvitski, T A; Anisimova, N V; Khotyleva, L V; Kilchevsky, A V; Blume, Ya B

    2015-01-01

    A bioinformatic search of sequences encoding cellulose synthase genes in the flax genome, and their comparison to dicots orthologs was carried out. The analysis revealed 32 cellulose synthase gene candidates, 16 of which are highly likely to encode cellulose synthases, and the remaining 16--cellulose synthase-like proteins (Csl). Phylogenetic analysis of gene products of cellulose synthase genes allowed distinguishing 6 groups of cellulose synthase genes of different classes: CesA1/10, CesA3, CesA4, CesA5/6/2/9, CesA7 and CesA8. Paralogous sequences within classes CesA1/10 and CesA5/6/2/9 which are associated with the primary cell wall formation are characterized by a greater similarity within these classes than orthologous sequences. Whereas the genes controlling the biosynthesis of secondary cell wall cellulose form distinct clades: CesA4, CesA7, and CesA8. The analysis of 16 identified flax cellulose synthase gene candidates shows the presence of at least 12 different cellulose synthase gene variants in flax genome which are represented in all six clades of cellulose synthase genes. Thus, at this point genes of all ten known cellulose synthase classes are identify in flax genome, but their correct classification requires additional research.

  10. Suites of terpene synthases explain differential terpenoid production in ginger and turmeric tissues.

    Directory of Open Access Journals (Sweden)

    Hyun Jo Koo

    Full Text Available The essential oils of ginger (Zingiber officinale and turmeric (Curcuma longa contain a large variety of terpenoids, some of which possess anticancer, antiulcer, and antioxidant properties. Despite their importance, only four terpene synthases have been identified from the Zingiberaceae family: (+-germacrene D synthase and (S-β-bisabolene synthase from ginger rhizome, and α-humulene synthase and β-eudesmol synthase from shampoo ginger (Zingiber zerumbet rhizome. We report the identification of 25 mono- and 18 sesquiterpene synthases from ginger and turmeric, with 13 and 11, respectively, being functionally characterized. Novel terpene synthases, (--caryolan-1-ol synthase and α-zingiberene/β-sesquiphellandrene synthase, which is responsible for formation of the major sesquiterpenoids in ginger and turmeric rhizomes, were also discovered. These suites of enzymes are responsible for formation of the majority of the terpenoids present in these two plants. Structures of several were modeled, and a comparison of sets of paralogs suggests how the terpene synthases in ginger and turmeric evolved. The most abundant and most important sesquiterpenoids in turmeric rhizomes, (+-α-turmerone and (+-β-turmerone, are produced from (--α-zingiberene and (--β-sesquiphellandrene, respectively, via α-zingiberene/β-sesquiphellandrene oxidase and a still unidentified dehydrogenase.

  11. Structure of the human beta-ketoacyl [ACP] synthase from the mitochondrial type II fatty acid synthase

    DEFF Research Database (Denmark)

    Christensen, Caspar Elo; Kragelund, Birthe B; von Wettstein-Knowles, Penny

    2007-01-01

    Two distinct ways of organizing fatty acid biosynthesis exist: the multifunctional type I fatty acid synthase (FAS) of mammals, fungi, and lower eukaryotes with activities residing on one or two polypeptides; and the dissociated type II FAS of prokaryotes, plastids, and mitochondria with individual...... activities encoded by discrete genes. The beta-ketoacyl [ACP] synthase (KAS) moiety of the mitochondrial FAS (mtKAS) is targeted by the antibiotic cerulenin and possibly by the other antibiotics inhibiting prokaryotic KASes: thiolactomycin, platensimycin, and the alpha-methylene butyrolactone, C75. The high...... degree of structural similarity between mitochondrial and prokaryotic KASes complicates development of novel antibiotics targeting prokaryotic KAS without affecting KAS domains of cytoplasmic FAS. KASes catalyze the C(2) fatty acid elongation reaction using either a Cys-His-His or Cys-His-Asn catalytic...

  12. Cloning and characterization of indole synthase (INS) and a putative tryptophan synthase α-subunit (TSA) genes from Polygonum tinctorium.

    Science.gov (United States)

    Jin, Zhehao; Kim, Jin-Hee; Park, Sang Un; Kim, Soo-Un

    2016-12-01

    Two cDNAs for indole-3-glycerol phosphate lyase homolog were cloned from Polygonum tinctorium. One encoded cytosolic indole synthase possibly in indigoid synthesis, whereas the other encoded a putative tryptophan synthase α-subunit. Indigo is an old natural blue dye produced by plants such as Polygonum tinctorium. Key step in plant indigoid biosynthesis is production of indole by indole-3-glycerol phosphate lyase (IGL). Two tryptophan synthase α-subunit (TSA) homologs, PtIGL-short and -long, were isolated by RACE PCR from P. tinctorium. The genome of the plant contained two genes coding for IGL. The short and the long forms, respectively, encoded 273 and 316 amino acid residue-long proteins. The short form complemented E. coli ΔtnaA ΔtrpA mutant on tryptophan-depleted agar plate signifying production of free indole, and thus was named indole synthase gene (PtINS). The long form, either intact or without the transit peptide sequence, did not complement the mutant and was tentatively named PtTSA. PtTSA was delivered into chloroplast as predicted by 42-residue-long targeting sequence, whereas PtINS was localized in cytosol. Genomic structure analysis suggested that a TSA duplicate acquired splicing sites during the course of evolution toward PtINS so that the targeting sequence-containing pre-mRNA segment was deleted as an intron. PtINS had about two to fivefolds higher transcript level than that of PtTSA, and treatment of 2,1,3-benzothiadiazole caused the relative transcript level of PtINS over PtTSA was significantly enhanced in the plant. The results indicate participation of PtINS in indigoid production.

  13. Development of a New Stretchable and Screen Printable Conductive Ink

    Science.gov (United States)

    Mohammed, Anwar A.

    Stretchable conductive ink is a key enabler for stretchable electronics. This thesis research focuses on the development of a new stretchable and screen printable conductive ink. After print and cure, this ink would be capable of being stretched by at least 500 cycles at 20% strain without increasing its resistance by more than 30 times the original resistance, while maintaining electrical and mechanical integrity. For a stretchable and screen-printable conductive ink, the correct morphology of the metal powder selected and the ability of the binder to be stretched after the sintering process, are both indispensable. This research has shown that a bi-modal mixture of fine and large-diameter silver flakes will improve stretchability. While the smaller flakes increase the conductivity and lower the sintering temperature, the larger flake particles promote ohmic connectivity during stretching. The bi-modal flake distribution increases connection points while enhancing packing density and lowering the thermal activation barrier. The polymer binder phase plays a crucial role in offering stretchability to the stretchable conductive inks. The silver flakes by themselves are not stretchable but they are contained within a stretchable binder system. The research demonstrates that commonly used printable ink binder when combined with large-chain polymers through a process known as 'elastomeric chain polymerization' will enable the conductive ink to become more stretchable. This research has shown that the new stretchable and screen printable silver conductive ink developed based upon the two insights mentioned above; (1) bi modal flakes to improve ohmic connectivity during stretching and (2) elastomeric chain polymerized binder system which could stretch even after the ink is sintered to the substrate, can exhibit an ink stretchability of at least 500 cycles at 20% strain while increasing the resistance by less than 30 times the original resistance. Wavy print patterns can

  14. Conductivity enhancement of ion tracks in tetrahedral amorphous carbon by doping with N, B, Cu and Fe

    International Nuclear Information System (INIS)

    Krauser, J.; Nix, A.-K.; Gehrke, H.-G.; Hofsäss, H.; Trautmann, C.; Weidinger, A.

    2012-01-01

    Conducting ion tracks are formed when high-energy heavy ions (e.g. 1 GeV Au) pass through tetrahedral amorphous carbon (ta-C). These nanowires with a diameter of about 8 nm are embedded in the insulating ta-C matrix and of interest for various nanotechnological applications. Usually the overall conductivity of the tracks and the current/voltage characteristics (Ohmic or non-Ohmic) vary strongly from track to track, even when measured on the same sample, indicating that the track formation is neither complete nor homogeneous. To improve the track conductivity, doping of ta-C with N, B, Cu, or Fe is investigated. Beneficial changes in track conductivity after doping compete with a conductivity increase of the surrounding matrix material. Best results are achieved by incorporation of 1 at.% Cu, while for different reasons, the improvement of the tracks remains moderate for N, B, and Fe doping. Conductivity enhancement of the tracks is assumed to develop during the ion track formation process by an increased number of localized states which contribute to the current transport.

  15. Self-organization process of a magnetohydrodynamic plasma in the presence of thermal conduction

    International Nuclear Information System (INIS)

    Zhu, Shao-ping; Horiuchi, Ritoku; Sato, Tetsuya; Watanabe, K.; Hayashi, T.; Todo, Y.; Watanabe, T.H.; Kageyama, A.; Takamaru, H.

    1995-12-01

    A self-organization process of a magnetohydrodynamic(MHD) plasma with a finite thermal conductivity is investigated by means of a three-dimensional MHD simulation. With no thermal conduction an MHD system self-organizes to a non-Taylor's state in which the electric current perpendicular to the magnetic field remains comparable to the parallel electric current. In the presence of thermal conductivity the perpendicular component of electric current and the nonuniformity of thermal pressure generated by driven reconnection tend to be smoothened. Thus, the self-organized state approaches to a force-free minimum energy state under the influence of thermal conduction. Detailed energy conversion processes are also studied to find that the rapid decay of magnetic energy during the self-organization process is caused not only through the ohmic heating, but also through the work done by the j x B force. (author)

  16. Monoterpene and sesquiterpene synthases and the origin of terpene skeletal diversity in plants.

    Science.gov (United States)

    Degenhardt, Jörg; Köllner, Tobias G; Gershenzon, Jonathan

    2009-01-01

    The multitude of terpene carbon skeletons in plants is formed by enzymes known as terpene synthases. This review covers the monoterpene and sesquiterpene synthases presenting an up-to-date list of enzymes reported and evidence for their ability to form multiple products. The reaction mechanisms of these enzyme classes are described, and information on how terpene synthase proteins mediate catalysis is summarized. Correlations between specific amino acid motifs and terpene synthase function are described, including an analysis of the relationships between active site sequence and cyclization type and a discussion of whether specific protein features might facilitate multiple product formation.

  17. Enhancement of vascular targeting by inhibitors of nitric oxide synthase

    International Nuclear Information System (INIS)

    Davis, Peter D.; Tozer, Gillian M.; Naylor, Matthew A.; Thomson, Peter; Lewis, Gemma; Hill, Sally A.

    2002-01-01

    Purpose: This study investigates the enhancement of the vascular targeting activity of the tubulin-binding agent combretastatin A4 phosphate (CA4P) by various inhibitors of nitric oxide synthases. Methods and Materials: The syngeneic tumors CaNT and SaS growing in CBA mice were used for this study. Reduction in perfused vascular volume was measured by injection of Hoechst 33342 24 h after drug administration. Necrosis (hematoxylin and eosin stain) was assessed also at 24 h after treatment. Combretastatin A4 phosphate was synthesized by a modification of the published procedure and the nitric oxide synthase inhibitors L-NNA, L-NMMA, L-NIO, L-NIL, S-MTC, S-EIT, AMP, AMT, and L-TC, obtained from commercial sources. Results: A statistically significant augmentation of the reduction in perfused vascular volume by CA4P in the CaNT tumor was observed with L-NNA, AMP, and AMT. An increase in CA4P-induced necrosis in the same tumor achieved significance with L-NNA, L-NMMA, L-NIL, and AMT. CA4P induced little necrosis in the SaS tumor, but combination with the inhibitors L-NNA, L-NMMA, L-NIO, S-EIT, and L-TC was effective. Conclusions: Augmentation of CA4P activity by nitric oxide synthase inhibitors of different structural classes supports a nitric oxide-related mechanism for this effect. L-NNA was the most effective inhibitor studied

  18. Incorporation of phosphate into glycogen by glycogen synthase.

    Science.gov (United States)

    Contreras, Christopher J; Segvich, Dyann M; Mahalingan, Krishna; Chikwana, Vimbai M; Kirley, Terence L; Hurley, Thomas D; DePaoli-Roach, Anna A; Roach, Peter J

    2016-05-01

    The storage polymer glycogen normally contains small amounts of covalently attached phosphate as phosphomonoesters at C2, C3 and C6 atoms of glucose residues. In the absence of the laforin phosphatase, as in the rare childhood epilepsy Lafora disease, the phosphorylation level is elevated and is associated with abnormal glycogen structure that contributes to the pathology. Laforin therefore likely functions in vivo as a glycogen phosphatase. The mechanism of glycogen phosphorylation is less well-understood. We have reported that glycogen synthase incorporates phosphate into glycogen via a rare side reaction in which glucose-phosphate rather than glucose is transferred to a growing polyglucose chain (Tagliabracci et al. (2011) Cell Metab13, 274-282). We proposed a mechanism to account for phosphorylation at C2 and possibly at C3. Our results have since been challenged (Nitschke et al. (2013) Cell Metab17, 756-767). Here we extend the evidence supporting our conclusion, validating the assay used for the detection of glycogen phosphorylation, measurement of the transfer of (32)P from [β-(32)P]UDP-glucose to glycogen by glycogen synthase. The (32)P associated with the glycogen fraction was stable to ethanol precipitation, SDS-PAGE and gel filtration on Sephadex G50. The (32)P-signal was not affected by inclusion of excess unlabeled UDP before analysis or by treatment with a UDPase, arguing against the signal being due to contaminating [β-(32)P]UDP generated in the reaction. Furthermore, [(32)P]UDP did not bind non-covalently to glycogen. The (32)P associated with glycogen was released by laforin treatment, suggesting that it was present as a phosphomonoester. The conclusion is that glycogen synthase can mediate the introduction of phosphate into glycogen, thereby providing a possible mechanism for C2, and perhaps C3, phosphorylation. Copyright © 2016 Elsevier Inc. All rights reserved.

  19. Microsomal prostaglandin E synthase-1 in rheumatic diseases

    Directory of Open Access Journals (Sweden)

    Marina eKorotkova

    2011-01-01

    Full Text Available Microsomal prostaglandin E synthase-1 (mPGES-1 is a well recognized target for the development of novel anti-inflammatory drugs that can reduce symptoms of inflammation in rheumatic diseases and other inflammatory conditions. In this review, we focus on mPGES-1 in rheumatic diseases with the aim to cover the most recent advances in the understanding of mPGES-1 in rheumatoid arthritis, osteoarthritis and inflammatory myopathies. Novel findings regarding regulation of mPGES1 cell expression as well as enzyme inhibitors are also summarized.

  20. Nitric oxide synthase expression and enzymatic activity in multiple sclerosis

    DEFF Research Database (Denmark)

    Broholm, H; Andersen, B; Wanscher, B

    2004-01-01

    We used post-mortem magnetic resonance imaging (MRI) guidance to obtain paired biopsies from the brains of four patients with clinical definite multiple sclerosis (MS). Samples were analyzed for the immunoreactivity (IR) of the three nitric oxide (NO) synthase isoforms [inducible, neuronal......NOS expressing cells in active lesions. NOS IR expressing cells were widely distributed in plaques, in white and gray matter that appeared normal macroscopically, and on MR. Endothelial NOS (eNOS) was highly expressed in intraparenchymal vascular endothelial cells of MS patients. A control group matched for age...

  1. Fatty acid synthase inhibitors isolated from Punica granatum L

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, He-Zhong [School of Life Science and Engineering, Southwest Jiaotong University, Chengdu, (China); Ma, Qing-Yun; Liang, Wen-Juan; Huang, Sheng-Zhuo; Dai, Hao-Fu; Wang, Peng-Cheng; Zhao, You-Xing, E-mail: zhaoyx1011@163.com [Institute of Tropical Bioscience and Biotechnology, Chinese Academy of Tropical Agricultural Sciences, Haikou (China); Fan, Hui-Jin; Ma, Xiao-Feng, E-mail: maxiaofeng@gucas.ac.cn [College of Life Sciences, Graduate University of Chinese Academy of Sciences, Beijing (China)

    2012-05-15

    The aim of this work is the isolation of fatty acid synthase (FAS) inhibitors from the ethyl acetate extracts of fruit peels of Punica granatum L. Bioassay-guided chemical investigation of the fruit peels resulted in the isolation of seventeen compounds mainly including triterpenoids and phenolic compounds, from which one new oleanane-type triterpene (punicaone) along with fourteen known compounds were isolated for the first time from this plant. Seven isolates were evaluated for inhibitory activities of FAS and two compounds showed to be active. Particularly, flavogallonic acid exhibited strong FAS inhibitory activity with IC{sub 50} value of 10.3 {mu}mol L{sup -1}. (author)

  2. Fatty acid synthase inhibitors isolated from Punica granatum L

    International Nuclear Information System (INIS)

    Jiang, He-Zhong; Ma, Qing-Yun; Liang, Wen-Juan; Huang, Sheng-Zhuo; Dai, Hao-Fu; Wang, Peng-Cheng; Zhao, You-Xing; Fan, Hui-Jin; Ma, Xiao-Feng

    2012-01-01

    The aim of this work is the isolation of fatty acid synthase (FAS) inhibitors from the ethyl acetate extracts of fruit peels of Punica granatum L. Bioassay-guided chemical investigation of the fruit peels resulted in the isolation of seventeen compounds mainly including triterpenoids and phenolic compounds, from which one new oleanane-type triterpene (punicaone) along with fourteen known compounds were isolated for the first time from this plant. Seven isolates were evaluated for inhibitory activities of FAS and two compounds showed to be active. Particularly, flavogallonic acid exhibited strong FAS inhibitory activity with IC 50 value of 10.3 μmol L -1 . (author)

  3. Thermodynamic and NMR analyses of NADPH binding to lipocalin-type prostaglandin D synthase

    International Nuclear Information System (INIS)

    Qin, Shubin; Shimamoto, Shigeru; Maruno, Takahiro; Kobayashi, Yuji; Kawahara, Kazuki; Yoshida, Takuya; Ohkubo, Tadayasu

    2015-01-01

    Lipocalin-type prostaglandin D synthase (L-PGDS) is one of the most abundant proteins in human cerebrospinal fluid (CSF) with dual functions as a prostaglandin D_2 (PGD_2) synthase and a transporter of lipophilic ligands. Recent studies revealed that L-PGDS plays important roles in protecting against various neuronal diseases induced by reactive oxygen species (ROS). However, the molecular mechanisms of such protective actions of L-PGDS remain unknown. In this study, we conducted thermodynamic and nuclear magnetic resonance (NMR) analyses, and demonstrated that L-PGDS binds to nicotinamide coenzymes, including NADPH, NADP"+, and NADH. Although a hydrophilic ligand is not common for L-PGDS, these ligands, especially NADPH showed specific interaction with L-PGDS at the upper pocket of its ligand-binding cavity with an unusually bifurcated shape. The binding affinity of L-PGDS for NADPH was comparable to that previously reported for NADPH oxidases and NADPH in vitro. These results suggested that L-PGDS potentially attenuates the activities of NADPH oxidases through interaction with NADPH. Given that NADPH is the substrate for NADPH oxidases that play key roles in neuronal cell death by generating excessive ROS, these results imply a novel linkage between L-PGDS and ROS. - Highlights: • Interactions of L-PGDS with nicotinamide coenzymes were studied by ITC and NMR. • The binding affinity of L-PGDS was strongest to NADPH among nicotinamide coenzymes. • NADPH binds to the upper part of L-PGDS ligand-binding cavity. • L-PGDS binds to both lipophilic and hydrophilic ligands. • This study implies a novel linkage between L-PGDS and reactive oxygen species.

  4. Thermodynamic and NMR analyses of NADPH binding to lipocalin-type prostaglandin D synthase

    Energy Technology Data Exchange (ETDEWEB)

    Qin, Shubin [Graduate School of Pharmaceutical Sciences, Osaka University, 1-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Shimamoto, Shigeru [Faculty of Science and Engineering, Kinki University, 3-4-1 Kowakae, Higashi-Osaka, Osaka 577-8502 (Japan); Maruno, Takahiro; Kobayashi, Yuji [Graduate School of Engineering, Osaka University, 2-1 Yamadaoka, Suita, Osaka 565-0871 (Japan); Kawahara, Kazuki; Yoshida, Takuya [Graduate School of Pharmaceutical Sciences, Osaka University, 1-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Ohkubo, Tadayasu, E-mail: ohkubo@phs.osaka-u.ac.jp [Graduate School of Pharmaceutical Sciences, Osaka University, 1-6 Yamadaoka, Suita, Osaka 565-0871 (Japan)

    2015-12-04

    Lipocalin-type prostaglandin D synthase (L-PGDS) is one of the most abundant proteins in human cerebrospinal fluid (CSF) with dual functions as a prostaglandin D{sub 2} (PGD{sub 2}) synthase and a transporter of lipophilic ligands. Recent studies revealed that L-PGDS plays important roles in protecting against various neuronal diseases induced by reactive oxygen species (ROS). However, the molecular mechanisms of such protective actions of L-PGDS remain unknown. In this study, we conducted thermodynamic and nuclear magnetic resonance (NMR) analyses, and demonstrated that L-PGDS binds to nicotinamide coenzymes, including NADPH, NADP{sup +}, and NADH. Although a hydrophilic ligand is not common for L-PGDS, these ligands, especially NADPH showed specific interaction with L-PGDS at the upper pocket of its ligand-binding cavity with an unusually bifurcated shape. The binding affinity of L-PGDS for NADPH was comparable to that previously reported for NADPH oxidases and NADPH in vitro. These results suggested that L-PGDS potentially attenuates the activities of NADPH oxidases through interaction with NADPH. Given that NADPH is the substrate for NADPH oxidases that play key roles in neuronal cell death by generating excessive ROS, these results imply a novel linkage between L-PGDS and ROS. - Highlights: • Interactions of L-PGDS with nicotinamide coenzymes were studied by ITC and NMR. • The binding affinity of L-PGDS was strongest to NADPH among nicotinamide coenzymes. • NADPH binds to the upper part of L-PGDS ligand-binding cavity. • L-PGDS binds to both lipophilic and hydrophilic ligands. • This study implies a novel linkage between L-PGDS and reactive oxygen species.

  5. Double diffusive magnetohydrodynamic heat and mass transfer of nanofluids over a nonlinear stretching/shrinking sheet with viscous-Ohmic dissipation and thermal radiation

    Directory of Open Access Journals (Sweden)

    Dulal Pal

    2017-03-01

    Full Text Available The study of magnetohydrodynamic (MHD convective heat and mass transfer near a stagnation-point flow over stretching/shrinking sheet of nanofluids is presented in this paper by considering thermal radiation, Ohmic heating, viscous dissipation and heat source/sink parameter effects. Non-similarity method is adopted for the governing basic equations before they are solved numerically using Runge-Kutta-Fehlberg method using shooting technique. The numerical results are validated by comparing the present results with previously published results. The focus of this paper is to study the effects of some selected governing parameters such as Richardson number, radiation parameter, Schimdt number, Eckert number and magnetic parameter on velocity, temperature and concentration profiles as well as on skin-friction coefficient, local Nusselt number and Sherwood number.

  6. On radiative-magnetoconvective heat and mass transfer of a nanofluid past a non-linear stretching surface with Ohmic heating and convective surface boundary condition

    Directory of Open Access Journals (Sweden)

    Shweta Mishra

    2016-12-01

    Full Text Available In this paper magnetoconvective heat and mass transfer characteristics of a two-dimensional steady flow of a nanofluid over a non-linear stretching sheet in the presence of thermal radiation, Ohmic heating and viscous dissipation have been investigated numerically. The model used for the nanofluid incorporates the effects of the Brownian motion and the presence of nanoparticles in the base fluid. The governing equations are transformed into a system of nonlinear ordinary differential equations by using similarity transformation. The numerical solutions are obtained by using fifth order Runge–Kutta–Fehlberg method with shooting technique. The non-dimensional parameters on velocity, temperature and concentration profiles and also on local Nusselt number and Sherwood number are discussed. The results indicate that the local skin friction coefficient decreases as the value of the magnetic parameter increases whereas the Nusselt number and Sherwood number increase as the values of the Brownian motion parameter and magnetic parameter increase.

  7. From coherent motion to localization: II. Dynamics of the spin-boson model with sub-Ohmic spectral density at zero temperature

    International Nuclear Information System (INIS)

    Wang Haobin; Thoss, Michael

    2010-01-01

    Graphical abstract: □□□ - Abstract: The dynamics of the spin-boson model at zero temperature is studied for a bath characterized by a sub-Ohmic spectral density. Using the numerically exact multilayer multiconfiguration time-dependent Hartree (ML-MCTDH) method, the population dynamics of the two-level subsystem has been investigated in a broad range of parameter space. The results show the transition of the dynamics from weakly damped coherent motion to localization upon increase of the system-bath coupling strength. Comparison of the exact ML-MCTDH simulations with the non-interacting blip approximation (NIBA) shows that the latter performs rather poorly in the weak coupling regime with small Kondo parameters. However, NIBA improves significantly upon increase in the coupling strength and is quantitatively correct in the strong coupling, nonadiabatic limit. The transition from coherent motion to localization as a function of the different parameters of the model is analyzed in some detail.

  8. Impact of recess etching and surface treatments on ohmic contacts regrown by molecular-beam epitaxy for AlGaN/GaN high electron mobility transistors

    Energy Technology Data Exchange (ETDEWEB)

    Joglekar, S.; Azize, M.; Palacios, T. [Microsystems Technology Laboratories, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, Massachusetts 02139 (United States); Beeler, M.; Monroy, E. [Université Grenoble-Alpes, 38000 Grenoble (France); CEA Grenoble, INAC-PHELIQS, 38000 Grenoble (France)

    2016-07-25

    Ohmic contacts fabricated by regrowth of n{sup +} GaN are favorable alternatives to metal-stack-based alloyed contacts in GaN-based high electron mobility transistors. In this paper, the influence of reactive ion dry etching prior to regrowth on the contact resistance in AlGaN/GaN devices is discussed. We demonstrate that the dry etch conditions modify the surface band bending, dangling bond density, and the sidewall depletion width, which influences the contact resistance of regrown contacts. The impact of chemical surface treatments performed prior to regrowth is also investigated. The sensitivity of the contact resistance to the surface treatments is found to depend upon the dangling bond density of the sidewall facets exposed after dry etching. A theoretical model has been developed in order to explain the observed trends.

  9. Molecular cloning and functional expression of geranylgeranyl pyrophosphate synthase from Coleus forskohlii Briq

    Directory of Open Access Journals (Sweden)

    Kawamukai Makoto

    2004-11-01

    Full Text Available Abstract Background Isopentenyl diphosphate (IPP, a common biosynthetic precursor to the labdane diterpene forskolin, has been biosynthesised via a non-mevalonate pathway. Geranylgeranyl diphosphate (GGPP synthase is an important branch point enzyme in terpenoid biosynthesis. Therefore, GGPP synthase is thought to be a key enzyme in biosynthesis of forskolin. Herein we report the first confirmation of the GGPP synthase gene in Coleus forskohlii Briq. Results The open reading frame for full-length GGPP synthase encodes a protein of 359 amino acids, in which 1,077 nucleotides long with calculated molecular mass of 39.3 kDa. Alignments of C. forskohlii GGPP synthase amino acid sequences revealed high homologies with other plant GGPP synthases. Several highly conserved regions, including two aspartate-rich motifs were identified. Transient expression of the N-terminal region of C. forskohlii GGPP synthase-GFP fusion protein in tobacco cells demonstrated subcellular localization in the chloroplast. Carotenoid production was observed in Escherichia coli harboring pACCAR25ΔcrtE from Erwinia uredovora and plasmid carrying C. forskohlii GGPP synthase. These results suggested that cDNA encoded functional GGPP synthase. Furthermore, C. forskohlii GGPP synthase expression was strong in leaves, decreased in stems and very little expression was observed in roots. Conclusion This investigation proposed that forskolin was synthesised via a non-mevalonate pathway. GGPP synthase is thought to be involved in the biosynthesis of forskolin, which is primarily synthesised in the leaves and subsequently accumulates in the stems and roots.

  10. Glycogen synthase from the parabasalian parasite Trichomonas vaginalis: An unusual member of the starch/glycogen synthase family.

    Science.gov (United States)

    Wilson, Wayne A; Pradhan, Prajakta; Madhan, Nayasha; Gist, Galen C; Brittingham, Andrew

    2017-07-01

    Trichomonas vaginalis, a parasitic protist, is the causative agent of the common sexually-transmitted infection trichomoniasis. The organism has long been known to synthesize substantial glycogen as a storage polysaccharide, presumably mobilizing this compound during periods of carbohydrate limitation, such as might be encountered during transmission between hosts. However, little is known regarding the enzymes of glycogen metabolism in T. vaginalis. We had previously described the identification and characterization of two forms of glycogen phosphorylase in the organism. Here, we measure UDP-glucose-dependent glycogen synthase activity in cell-free extracts of T. vaginalis. We then demonstrate that the TVAG_258220 open reading frame encodes a glycosyltransferase that is presumably responsible for this synthetic activity. We show that expression of TVAG_258220 in a yeast strain lacking endogenous glycogen synthase activity is sufficient to restore glycogen accumulation. Furthermore, when TVAG_258220 is expressed in bacteria, the resulting recombinant protein has glycogen synthase activity in vitro, transferring glucose from either UDP-glucose or ADP-glucose to glycogen and using both substrates with similar affinity. This protein is also able to transfer glucose from UDP-glucose or ADP-glucose to maltose and longer oligomers of glucose but not to glucose itself. However, with these substrates, there is no evidence of processivity and sugar transfer is limited to between one and three glucose residues. Taken together with our earlier work on glycogen phosphorylase, we are now well positioned to define both how T. vaginalis synthesizes and utilizes glycogen, and how these processes are regulated. Copyright © 2017 Elsevier B.V. and Société Française de Biochimie et Biologie Moléculaire (SFBBM). All rights reserved.

  11. Stereochemical course of enzyme-catalyzed aminopropyl transfer: spermidine synthase

    International Nuclear Information System (INIS)

    Kullberg, D.W.; Orr, G.R.; Coward, J.K.

    1986-01-01

    The R and S enantionmers of S-adenosyl-3-[ 2 H]3-(methylthio)-1-propylamine (decarboxylated S-adenosylmethionine), previously synthesized in this laboratory, were incubated with [1,4- 2 H 4 ]-putrescine in the presence of spermidine synthase from E. coli. The resulting chiral [ 2 H 5 ]spermidines were isolated and converted to their N 1 ,N 7 -dibocspermidine-N 4 -(1S,4R)-camphanamides. The derivatives were analyzed by 500 MHz 1 H-NMR and the configuration of the chiral center assigned by correlation with the spectra of synthetic chiral [ 2 H 3 ]dibocspermidine camphanamide standards. The enzyme-catalyzed aminopropyl transfer was shown to occur with net retention of configuration, indicative of a double-displacement mechanism. This result concurs with that of a previous steady-state kinetics study of spermidine synthase isolated from E. coli, but contradicts the single-displacement mechanism suggested by a stereochemical analysis of chiral spermidines biosynthesized in E. coli treated with chirally deuterated methionines. It also indicates that this aminopropyltransferase is mechanistically distinct from the methyltransferases, which have been shown to act via a single-displacement mechanism (net inversion at -CH 3 ) in all cases studied to date

  12. In Vitro Biochemical Characterization of All Barley Endosperm Starch Synthases

    Directory of Open Access Journals (Sweden)

    Jose Antonio Cuesta-Seijo

    2016-01-01

    Full Text Available Starch is the main storage polysaccharide in cereals and the major source of calories in the human diet. It is synthesized by a panel of enzymes including five classes of starch synthases (SSs. While the overall starch synthase (SS reaction is known, the functional differences between the five SS classes are poorly understood. Much of our knowledge comes from analyzing mutant plants with altered SS activities, but the resulting data are often difficult to interpret as a result of pleitropic effects, competition between enzymes, overlaps in enzyme activity and disruption of multi-enzyme complexes. Here we provide a detailed biochemical study of the activity of all five classes of SSs in barley endosperm. Each enzyme was produced recombinantly in E. coli and the properties and modes of action in vitro were studied in isolation from other SSs and other substrate modifying activities. Our results define the mode of action of each SS class in unprecedented detail; we analyze their substrate selection, temperature dependence and stability, substrate affinity and temporal abundance during barley development. Our results are at variance with some generally accepted ideas about starch biosynthesis and might lead to the reinterpretation of results obtained in planta. In particular, they indicate that granule bound SS is capable of processive action even in the absence of a starch matrix, that SSI has no elongation limit, and that SSIV, believed to be critical for the initiation of starch granules, has maltoligosaccharides and not polysaccharides as its preferred substrates.

  13. Modulation of hyaluronan synthase activity in cellular membrane fractions.

    Science.gov (United States)

    Vigetti, Davide; Genasetti, Anna; Karousou, Evgenia; Viola, Manuela; Clerici, Moira; Bartolini, Barbara; Moretto, Paola; De Luca, Giancarlo; Hascall, Vincent C; Passi, Alberto

    2009-10-30

    Hyaluronan (HA), the only non-sulfated glycosaminoglycan, is involved in morphogenesis, wound healing, inflammation, angiogenesis, and cancer. In mammals, HA is synthesized by three homologous HA synthases, HAS1, HAS2, and HAS3, that polymerize the HA chain using UDP-glucuronic acid and UDP-N-acetylglucosamine as precursors. Since the amount of HA is critical in several pathophysiological conditions, we developed a non-radioactive assay for measuring the activity of HA synthases (HASs) in eukaryotic cells and addressed the question of HAS activity during intracellular protein trafficking. We prepared three cellular fractions: plasma membrane, cytosol (containing membrane proteins mainly from the endoplasmic reticulum and Golgi), and nuclei. After incubation with UDP-sugar precursors, newly synthesized HA was quantified by polyacrylamide gel electrophoresis of fluorophore-labeled saccharides and high performance liquid chromatography. This new method measured HAS activity not only in the plasma membrane fraction but also in the cytosolic membranes. This new technique was used to evaluate the effects of 4-methylumbeliferone, phorbol 12-myristate 13-acetate, interleukin 1beta, platelet-derived growth factor BB, and tunicamycin on HAS activities. We found that HAS activity can be modulated by post-translational modification, such as phosphorylation and N-glycosylation. Interestingly, we detected a significant increase in HAS activity in the cytosolic membrane fraction after tunicamycin treatment. Since this compound is known to induce HA cable structures, this result links HAS activity alteration with the capability of the cell to promote HA cable formation.

  14. Glycogen synthase kinase 3: more than a namesake.

    Science.gov (United States)

    Rayasam, Geetha Vani; Tulasi, Vamshi Krishna; Sodhi, Reena; Davis, Joseph Alex; Ray, Abhijit

    2009-03-01

    Glycogen synthase kinase 3 (GSK3), a constitutively acting multi-functional serine threonine kinase is involved in diverse physiological pathways ranging from metabolism, cell cycle, gene expression, development and oncogenesis to neuroprotection. These diverse multiple functions attributed to GSK3 can be explained by variety of substrates like glycogen synthase, tau protein and beta catenin that are phosphorylated leading to their inactivation. GSK3 has been implicated in various diseases such as diabetes, inflammation, cancer, Alzheimer's and bipolar disorder. GSK3 negatively regulates insulin-mediated glycogen synthesis and glucose homeostasis, and increased expression and activity of GSK3 has been reported in type II diabetics and obese animal models. Consequently, inhibitors of GSK3 have been demonstrated to have anti-diabetic effects in vitro and in animal models. However, inhibition of GSK3 poses a challenge as achieving selectivity of an over achieving kinase involved in various pathways with multiple substrates may lead to side effects and toxicity. The primary concern is developing inhibitors of GSK3 that are anti-diabetic but do not lead to up-regulation of oncogenes. The focus of this review is the recent advances and the challenges surrounding GSK3 as an anti-diabetic therapeutic target.

  15. Polyketide synthases from poison hemlock (Conium maculatum L.).

    Science.gov (United States)

    Hotti, Hannu; Seppänen-Laakso, Tuulikki; Arvas, Mikko; Teeri, Teemu H; Rischer, Heiko

    2015-11-01

    Coniine is a toxic alkaloid, the biosynthesis of which is not well understood. A possible route, supported by evidence from labelling experiments, involves a polyketide formed by the condensation of one acetyl-CoA and three malonyl-CoAs catalysed by a polyketide synthase (PKS). We isolated PKS genes or their fragments from poison hemlock (Conium maculatum L.) by using random amplification of cDNA ends (RACE) and transcriptome analysis, and characterized three full-length enzymes by feeding different starter-CoAs in vitro. On the basis of our in vitro experiments, two of the three characterized PKS genes in poison hemlock encode chalcone synthases (CPKS1 and CPKS2), and one encodes a novel type of PKS (CPKS5). We show that CPKS5 kinetically favours butyryl-CoA as a starter-CoA in vitro. Our results suggest that CPKS5 is responsible for the initiation of coniine biosynthesis by catalysing the synthesis of the carbon backbone from one butyryl-CoA and two malonyl-CoAs. © 2015 FEBS.

  16. Amaryllidaceae Alkaloids as Potential Glycogen Synthase Kinase-3β Inhibitors

    Directory of Open Access Journals (Sweden)

    Daniela Hulcová

    2018-03-01

    Full Text Available Glycogen synthase kinase-3β (GSK-3β is a multifunctional serine/threonine protein kinase that was originally identified as an enzyme involved in the control of glycogen metabolism. It plays a key role in diverse physiological processes including metabolism, the cell cycle, and gene expression by regulating a wide variety of well-known substances like glycogen synthase, tau-protein, and β-catenin. Recent studies have identified GSK-3β as a potential therapeutic target in Alzheimer´s disease, bipolar disorder, stroke, more than 15 types of cancer, and diabetes. GSK-3β is one of the most attractive targets for medicinal chemists in the discovery, design, and synthesis of new selective potent inhibitors. In the current study, twenty-eight Amaryllidaceae alkaloids of various structural types were studied for their potency to inhibit GSK-3β. Promising results have been demonstrated by alkaloids of the homolycorine-{9-O-demethylhomolycorine (IC50 = 30.00 ± 0.71 µM, masonine (IC50 = 27.81 ± 0.01 μM}, and lycorine-types {caranine (IC50 = 30.75 ± 0.04 μM}.

  17. The crystal structure of human GDP-L-fucose synthase.

    Science.gov (United States)

    Zhou, Huan; Sun, Lihua; Li, Jian; Xu, Chunyan; Yu, Feng; Liu, Yahui; Ji, Chaoneng; He, Jianhua

    2013-09-01

    Human GDP-l-fucose synthase, also known as FX protein, synthesizes GDP-l-fucose from its substrate GDP-4-keto-6-deoxy-d-mannose. The reaction involves epimerization at both C-3 and C-5 followed by an NADPH-dependent reduction of the carbonyl at C-4. In this paper, the first crystal structure of human FX protein was determined at 2.37 Å resolution. The asymmetric unit of the crystal structure contains four molecules which form two homodimers. Each molecule consists of two domains, a Rossmann-fold NADPH-binding motif and a carboxyl terminal domain. Compared with the Escherichia coli GDP-l-fucose synthase, the overall structures of these two enzymes have four major differences. There are four loops in the structure of human FX protein corresponding to two α-helices and two β-sheets in that of the E. coli enzyme. Besides, there are seven different amino acid residues binding with NAPDH comparing human FX protein with that from E. coli. The structure of human FX reveals the key catalytic residues and could be useful for the design of drugs for the treatment of inflammation, auto-immune diseases, and possibly certain types of cancer.

  18. Prostaglandin E(2) synthase inhibition as a therapeutic target.

    Science.gov (United States)

    Iyer, Jitesh P; Srivastava, Punit K; Dev, Rishabh; Dastidar, Sunanda G; Ray, Abhijit

    2009-07-01

    Most NSAIDs function by inhibiting biosynthesis of PGE(2) by inhibition of COX-1 and/or COX-2. Since COX-1 has a protective function in the gastro-intestinal tract (GIT), non-selective inhibition of both cycloxy genases leads to moderate to severe gastro-intestinal intolerance. Attempts to identify selective inhibitors of COX-2, led to the identification of celecoxib and rofecoxib. However, long-term use of these drugs has serious adverse effects of sudden myocardial infarction and thrombosis. Drug-mediated imbalance in the levels of prostaglandin I(2) (PGI(2)) and thromboxane A(2) (TXA(2)) with a bias towards TXA(2) may be the primary reason for these events. This resulted in the drugs being withdrawn from the market, leaving a need for an effective and safe anti-inflammatory drug. Recently, the focus of research has shifted to enzymes downstream of COX in the prosta glandin biosynthetic pathway such as prostaglandin E(2) synthases. Microsomal prostaglandin E(2) synthase-1 (mPGES-1) specifically isomerizes PGH(2) to PGE(2), under inflammatory conditions. In this review, we examine the biology of mPGES-1 and its role in disease. Progress in designing molecules that can selectively inhibit mPGES-1 is reviewed. mPGES-1 has the potential to be a target for anti-inflammatory therapy, devoid of adverse GIT and cardiac effects and warrants further investigation.

  19. Chromosomal localization of the human and mouse hyaluronan synthase genes

    Energy Technology Data Exchange (ETDEWEB)

    Spicer, A.P.; McDonald, J.A. [Mayo Clinic Scottsdale, AZ (United States); Seldin, M.F. [Univ. of California Davis, CA (United States)] [and others

    1997-05-01

    We have recently identified a new vertebrate gene family encoding putative hyaluronan (HA) synthases. Three highly conserved related genes have been identified, designated HAS1, HAS2, and HAS3 in humans and Has1, Has2, and Has3 in the mouse. All three genes encode predicted plasma membrane proteins with multiple transmembrane domains and approximately 25% amino acid sequence identity to the Streptococcus pyogenes HA synthase, HasA. Furthermore, expression of any one HAS gene in transfected mammalian cells leads to high levels of HA biosynthesis. We now report the chromosomal localization of the three HAS genes in human and in mouse. The genes localized to three different positions within both the human and the mouse genomes. HAS1 was localized to the human chromosome 19q13.3-q13.4 boundary and Has1 to mouse Chr 17. HAS2 was localized to human chromosome 8q24.12 and Has2 to mouse Chr 15. HAS3 was localized to human chromosome 16q22.1 and Has3 to mouse Chr 8. The map position for HAS1 reinforces the recently reported relationship between a small region of human chromosome 19q and proximal mouse chromosome 17. HAS2 mapped outside the predicted critical region delineated for the Langer-Giedion syndrome and can thus be excluded as a candidate gene for this genetic syndrome. 33 refs., 2 figs.

  20. Selectivity of the surface binding site (SBS) on barley starch synthase I

    DEFF Research Database (Denmark)

    Wilkens, Casper; Cuesta-Seijo, Jose A.; Palcic, Monica

    2014-01-01

    Starch synthase I (SSI) from various sources has been shown to preferentially elongate branch chains of degree of polymerisation (DP) from 6–7 to produce chains of DP 8–12. In the recently determined crystal structure of barley starch synthase I (HvSSI) a so-called surface binding site (SBS) was ...

  1. Inhibition of the ATP Synthase Eliminates the Intrinsic Resistance of Staphylococcus aureus towards Polymyxins

    DEFF Research Database (Denmark)

    Vestergaard, Martin; Nøhr-Meldgaard, Katrine; Bojer, Martin Saxtorph

    2017-01-01

    , linezolid, daptomycin, and oxacillin were unchanged. ATP synthase activity is known to be inhibited by oligomycin A, and the presence of this compound increased polymyxin B-mediated killing of S. aureus Our results demonstrate that the ATP synthase contributes to intrinsic resistance of S. aureus towards...

  2. Creation of a high-amylose durum wheat through mutagenesis of starch synthase II (SSIIa)

    Science.gov (United States)

    In cereal seeds mutations in one or more starch synthases lead to decreased amylopectin and increased amylose content. Here, the impact of starch synthase IIa (SSIIa or SGP-1) mutations upon durum starch was investigated. A screen of durum accessions identified two lines lacking SGP-A1, the A geno...

  3. Cytidine triphosphate synthase activity and mRNA expression in normal human blood cells

    NARCIS (Netherlands)

    Verschuur, A. C.; van Gennip, A. H.; Muller, E. J.; Voûte, P. A.; Vreken, P.; van Kuilenburg, A. B.

    1999-01-01

    Cytidine triphosphate (CTP) synthase is one of the key enzymes in pyrimidine nucleotide anabolic pathways. The activity of this enzyme is elevated in various malignancies including acute lymphocytic leukemia (ALL). In this study we investigated the activity of CTP synthase in various human blood

  4. Cloning and sequence analysis of putative type II fatty acid synthase ...

    Indian Academy of Sciences (India)

    Prakash

    Cloning and sequence analysis of putative type II fatty acid synthase genes from Arachis hypogaea L. ... acyl carrier protein (ACP), malonyl-CoA:ACP transacylase, β-ketoacyl-ACP .... Helix II plays a dominant role in the interaction ... main distinguishing features of plant ACPs in plastids and ..... synthase component; J. Biol.

  5. Reduced methylation of the thromboxane synthase gene is correlated with its increased vascular expression in preeclampsia.

    Science.gov (United States)

    Mousa, Ahmad A; Strauss, Jerome F; Walsh, Scott W

    2012-06-01

    Preeclampsia is characterized by increased thromboxane and decreased prostacyclin levels, which predate symptoms, and can explain some of the clinical manifestations of preeclampsia, including hypertension and thrombosis. In this study, we examined DNA methylation of the promoter region of the thromboxane synthase gene (TBXAS1) and the expression of thromboxane synthase in systemic blood vessels of normal pregnant and preeclamptic women. Thromboxane synthase is responsible for the synthesis of thromboxane A(2), a potent vasoconstrictor and activator of platelets. We also examined the effect of experimentally induced DNA hypomethylation on the expression of thromboxane synthase in a neutrophil-like cell line (HL-60 cells) and in cultured vascular smooth muscle and endothelial cells. We found that DNA methylation of the TBXAS1 promoter was decreased and thromboxane synthase expression was increased in omental arteries of preeclamptic women as compared with normal pregnant women. Increased thromboxane synthase expression was observed in vascular smooth muscles cells, endothelial cells, and infiltrating neutrophils. Experimentally induced DNA hypomethylation only increased expression of thromboxane synthase in the neutrophil-like cell line, whereas tumor necrosis factor-α, a neutrophil product, increased its expression in cultured vascular smooth muscle cells. Our study suggests that epigenetic mechanisms and release of tumor necrosis factor-α by infiltrating neutrophils could contribute to the increased expression of thromboxane synthase in maternal systemic blood vessels, contributing to the hypertension and coagulation abnormalities associated with preeclampsia.

  6. Tunneling and resonant conductance in one-dimensional molecular structures

    International Nuclear Information System (INIS)

    Kozhushner, M.A.; Posvyanskii, V.S.; Oleynik, I.I.

    2005-01-01

    We present a theory of tunneling and resonant transitions in one-dimensional molecular systems which is based on Green's function theory of electron sub-barrier scattering off the structural units (or functional groups) of a molecular chain. We show that the many-electron effects are of paramount importance in electron transport and they are effectively treated using a formalism of sub-barrier scattering operators. The method which calculates the total scattering amplitude of the bridge molecule not only predicts the enhancement of the amplitude of tunneling transitions in course of tunneling electron transfer through onedimensional molecular structures but also allows us to interpret conductance mechanisms by calculating the bound energy spectrum of the tunneling electron, the energies being obtained as poles of the total scattering amplitude of the bridge molecule. We found that the resonant tunneling via bound states of the tunneling electron is the major mechanism of electron conductivity in relatively long organic molecules. The sub-barrier scattering technique naturally includes a description of tunneling in applied electric fields which allows us to calculate I-V curves at finite bias. The developed theory is applied to explain experimental findings such as bridge effect due to tunneling through organic molecules, and threshold versus Ohmic behavior of the conductance due to resonant electron transfer

  7. Multidimensional Heat Conduction

    DEFF Research Database (Denmark)

    Rode, Carsten

    1998-01-01

    Analytical theory of multidimensional heat conduction. General heat conduction equation in three dimensions. Steay state, analytical solutions. The Laplace equation. Method of separation of variables. Principle of superposition. Shape factors. Transient, multidimensional heat conduction....

  8. Carbon black reinforced C8 ether linked bismaleimide toughened electrically conducting epoxy nanocomposites

    International Nuclear Information System (INIS)

    Mandhakini, M.; Chandramohan, A.; Jayanthi, K.; Alagar, M.

    2014-01-01

    Highlight: • The toughness of the epoxy is improved with C8e-BMI. • Conduction through ohmic contact chain takes the leading mechanism for electrical conduction instead of tunneling with 5 wt% CB. • The phase segregation between epoxy/C8 e-BMI improves the toughness of the nanocomposite. • Both toughening and flexibilization effect is responsible for improvement in impact strength. • The largest challenge of appropriate balance between the electrical conductivity and mechanical behavior is attained in a cost effective manner. - Abstract: The present work deals with the toughening of brittle epoxy matrix with C8 ether linked bismaleimide (C8 e-BMI) and then study the reinforcing effect of carbon black (CB) in enhancing the conducting properties of insulating epoxy matrix. The Fourier transform infrared spectroscopy (FTIR) and Raman analysis indicate the formation of strong covalent bonds between CB and C8 e-BMI/epoxy matrix. The X-ray diffraction (XRD) and Field Emission Scanning Electron Microscope (FESEM) analysis indicate the event of phase separation in 5 wt% CB loaded epoxy C8 e-BMI nanocomposites. The impact strength increased up to 5 wt% of CB loading with particle pull and crack deflection to be driving mechanism for enhancing the toughness of the nanocomposite and beyond 5 wt% the impact strength started to decrease due to aggregation of CB. The dynamic mechanical analysis (DMA) also indicates the toughness of the nanocomposites was improved with 5 wt% of CB loading due to the phase segregation between epoxy and C8 e-BMI in the presence of CB. The electrical conductivity was also increased with 5 wt% of CB due to classical conduction by ohmic chain contact

  9. Functional specificity of cardiolipin synthase revealed by the identification of a cardiolipin synthase CrCLS1 in Chlamydomonas reinhardtii

    Directory of Open Access Journals (Sweden)

    Chun-Hsien eHung

    2016-01-01

    Full Text Available Phosphatidylglycerol (PG and cardiolipin (CL are two essential classes of phospholipid in plants and algae. Phosphatidylglycerophosphate synthase (PGPS and cardiolipin synthase (CLS involved in the biosynthesis of PG and CL belong to CDP-alcohol phosphotransferase and share overall amino acid sequence homology. However, it remains elusive whether PGPS and CLS are functionally distinct in vivo. Here, we report identification of a gene encoding CLS in Chlamydomonas reinhardtii, CrCLS1, and its functional compatibility. Whereas CrCLS1 did not complement the growth phenotype of a PGPS mutant of Synechocystis sp. PCC 6803, it rescued the temperature-sensitive growth phenotype, growth profile with different carbon sources, phospholipid composition and enzyme activity of ∆crd1, a CLS mutant of Saccharomyces cerevisiae. These results suggest that CrCLS1 encodes a functional CLS of C. reinhardtii as the first identified algal CLS, whose enzyme function is distinct from that of PGPSs from C. reinhardtii. Comparison of CDP-alcohol phosphotransferase motif between PGPS and CLS among different species revealed a possible additional motif that might define the substrate specificity of these closely related enzymes.

  10. Geranylgeranyl diphosphate synthase from Scoparia dulcis and Croton sublyratus. Plastid localization and conversion to a farnesyl diphosphate synthase by mutagenesis.

    Science.gov (United States)

    Sitthithaworn, W; Kojima, N; Viroonchatapan, E; Suh, D Y; Iwanami, N; Hayashi, T; Noji, M; Saito, K; Niwa, Y; Sankawa, U

    2001-02-01

    cDNAs encoding geranylgeranyl diphosphate synthase (GGPPS) of two diterpene-producing plants, Scoparia dulcis and Croton sublyratus, have been isolated using the homology-based polymerase chain reaction (PCR) method. Both clones contained highly conserved aspartate-rich motifs (DDXX(XX)D) and their N-terminal residues exhibited the characteristics of chloroplast targeting sequence. When expressed in Escherichia coli, both the full-length and truncated proteins in which the putative targeting sequence was deleted catalyzed the condensation of farnesyl diphosphate and isopentenyl diphosphate to produce geranylgeranyl diphosphate (GGPP). The structural factors determining the product length in plant GGPPSs were investigated by constructing S. dulcis GGPPS mutants on the basis of sequence comparison with the first aspartate-rich motif (FARM) of plant farnesyl diphosphate synthase. The result indicated that in plant GGPPSs small amino acids, Met and Ser, at the fourth and fifth positions before FARM and Pro and Cys insertion in FARM play essential roles in determination of product length. Further, when a chimeric gene comprised of the putative transit peptide of the S. dulcis GGPPS gene and a green fluorescent protein was introduced into Arabidopsis leaves by particle gun bombardment, the chimeric protein was localized in chloroplasts, indicating that the cloned S. dulcis GGPPS is a chloroplast protein.

  11. Riboflavin accumulation and characterization of cDNAs encoding lumazine synthase and riboflavin synthase in bitter melon (Momordica charantia).

    Science.gov (United States)

    Tuan, Pham Anh; Kim, Jae Kwang; Lee, Sanghyun; Chae, Soo Cheon; Park, Sang Un

    2012-12-05

    Riboflavin (vitamin B2) is the universal precursor of the coenzymes flavin mononucleotide and flavin adenine dinucleotide--cofactors that are essential for the activity of a wide variety of metabolic enzymes in animals, plants, and microbes. Using the RACE PCR approach, cDNAs encoding lumazine synthase (McLS) and riboflavin synthase (McRS), which catalyze the last two steps in the riboflavin biosynthetic pathway, were cloned from bitter melon (Momordica charantia), a popular vegetable crop in Asia. Amino acid sequence alignments indicated that McLS and McRS share high sequence identity with other orthologous genes and carry an N-terminal extension, which is reported to be a plastid-targeting sequence. Organ expression analysis using quantitative real-time RT PCR showed that McLS and McRS were constitutively expressed in M. charantia, with the strongest expression levels observed during the last stage of fruit ripening (stage 6). This correlated with the highest level of riboflavin content, which was detected during ripening stage 6 by HPLC analysis. McLS and McRS were highly expressed in the young leaves and flowers, whereas roots exhibited the highest accumulation of riboflavin. The cloning and characterization of McLS and McRS from M. charantia may aid the metabolic engineering of vitamin B2 in crops.

  12. Application of a Colorimetric Assay to Identify Putative Ribofuranosylaminobenzene 5'-Phosphate Synthase Genes Expressed with Activity in Escherichia coli

    OpenAIRE

    Bechard, Matthew E.; Chhatwal, Sonya; Garcia, Rosemarie E.; Rasche, Madeline E.

    2003-01-01

    Tetrahydromethanopterin (H4MPT) is a tetrahydrofolate analog originally discovered in methanogenic archaea, but later found in other archaea and bacteria. The extent to which H4MPT occurs among living organisms is unknown. The key enzyme which distinguishes the biosynthetic pathways of H4MPT and tetrahydrofolate is ribofuranosylaminobenzene 5'-phosphate synthase (RFAP synthase). Given the importance of RFAP synthase in H4MPT biosynthesis, the identification of putative RFAP synthase genes and...

  13. Cloning and heterologous expression of a novel subgroup of class IV polyhydroxyalkanoate synthase genes from the genus Bacillus.

    Science.gov (United States)

    Mizuno, Kouhei; Kihara, Takahiro; Tsuge, Takeharu; Lundgren, Benjamin R; Sarwar, Zaara; Pinto, Atahualpa; Nomura, Christopher T

    2017-01-01

    Many microorganisms harbor genes necessary to synthesize biodegradable plastics known as polyhydroxyalkanoates (PHAs). We surveyed a genomic database and discovered a new cluster of class IV PHA synthase genes (phaRC). These genes are different in sequence and operon structure from any previously reported PHA synthase. The newly discovered PhaRC synthase was demonstrated to produce PHAs in recombinant Escherichia coli.

  14. Altering the expression of two chitin synthase genes differentially affects the growth and morphology of Aspergillus oryzae

    DEFF Research Database (Denmark)

    Müller, Christian; Hjort, C.M.; Hansen, K.

    2002-01-01

    In Aspergillus oryzae, one full-length chitin synthase (chsB) and fragments of two other chitin synthases (csmA and chsC) were identified. The deduced amino acid sequence of chsB was similar (87% identity) to chsB from Aspergillus nidulans, which encodes a class III chitin synthase. The sequence...

  15. Conducting compositions of matter

    Science.gov (United States)

    Viswanathan, Tito (Inventor)

    2000-01-01

    The invention provides conductive compositions of matter, as well as methods for the preparation of the conductive compositions of matter, solutions comprising the conductive compositions of matter, and methods of preparing fibers or fabrics having improved anti-static properties employing the conductive compositions of matter.

  16. Corn silk induces nitric oxide synthase in murine macrophages.

    Science.gov (United States)

    Kim, Kyung A; Choi, Sang Kyu; Choi, Hye Seon

    2004-12-31

    Corn silk has been purified as an anticoagulant previously and the active component is a polysaccharide with a molecular mass of 135 kDa. It activates murine macrophages to induce nitric oxide synthase (NOS) and generate substantial amounts of NO in time and dose-dependent manners. It was detectable first at 15 h after stimulation by corn silk, peaked at 24 h, and undetectable by 48 h. Induction of NOS is inhibited by pyrolidine dithiocarbamate (PDTC) and genistein, an inhibitor of nuclear factor kappa B (NF-kappaB) and tyrosine kinase, respectively, indicating that iNOS stimulated by corn silk is associated with tyrosine kinase and NF-kappaB signaling pathways. IkappaB-alpha degradation was detectible at 10 min, and the level was restored at 120 min after treatment of corn silk. Corn silk induced nuclear translocation of NF-kappaB by phosphorylation and degradation of IkappaB-alpha.

  17. CTP synthase forms the cytoophidium in human hepatocellular carcinoma.

    Science.gov (United States)

    Chang, Chia-Chun; Jeng, Yung-Ming; Peng, Min; Keppeke, Gerson Dierley; Sung, Li-Ying; Liu, Ji-Long

    2017-12-15

    CTP synthase (CTPS) can aggregate into an intracellular macrostructure, the cytoophidium, in various organisms including human cells. Previous studies have shown that assembly of human CTPS cytoophidia may be correlated with the cellular metabolic status, and is able to promote the activity of CTPS. A correlation between the cytoophidium and cancer metabolism has been proposed but not yet been revealed. In the current study we provide clear evidence of the presence of CTPS cytoophidia in various human cancers and some non-cancerous tissues. Moreover, among 203 tissue samples of hepatocellular carcinoma, 56 (28%) samples exhibited many cytoophidia, whereas no cytoophidia were detected in adjacent non-cancerous hepatocytes for all samples. Our findings suggest that the CTPS cytoophidium may participate in the adaptive metabolism of human hepatocellular carcinoma. Copyright © 2017. Published by Elsevier Inc.

  18. Reduced ceramide synthase 2 activity causes progressive myoclonic epilepsy

    DEFF Research Database (Denmark)

    Mosbech, Mai-Britt; Olsen, Anne S B; Neess, Ditte

    2014-01-01

    between genes involved in SL metabolism and epilepsy. METHODS: We used quantitative real-time PCR, Western blotting, and enzymatic assays to determine the mRNA, protein, and activity levels of ceramide synthase 2 (CERS2) in fiibroblasts isolated from parental control subjects and from a patient diagnosed...... with progressive myoclonic epilepsy (PME). Mass spectrometry and fluorescence microscopy were used to examine the effects of reduced CERS2 activity on cellular lipid composition and plasma membrane functions. RESULTS: We identify a novel 27 kb heterozygous deletion including the CERS2 gene in a proband diagnosed...... with PME. Compared to parental controls, levels of CERS2 mRNA, protein, and activity were reduced by ˜50% in fibroblasts isolated from this proband, resulting in significantly reduced levels of ceramides and sphingomyelins containing the very long-chain fatty acids C24:0 and C26:0. The change in SL...

  19. Sphingomyelin Synthase 1 Is Essential for Male Fertility in Mice.

    Directory of Open Access Journals (Sweden)

    Anke Wittmann

    Full Text Available Sphingolipids and the derived gangliosides have critical functions in spermatogenesis, thus mutations in genes involved in sphingolipid biogenesis are often associated with male infertility. We have generated a transgenic mouse line carrying an insertion in the sphingomyelin synthase gene Sms1, the enzyme which generates sphingomyelin species in the Golgi apparatus. We describe the spermatogenesis defect of Sms1-/- mice, which is characterized by sloughing of spermatocytes and spermatids, causing progressive infertility of male homozygotes. Lipid profiling revealed a reduction in several long chain unsaturated phosphatidylcholins, lysophosphatidylcholins and sphingolipids in the testes of mutants. Multi-Spectral Optoacoustic Tomography indicated blood-testis barrier dysfunction. A supplementary diet of the essential omega-3 docosahexaenoic acid and eicosapentaenoic acid diminished germ cell sloughing from the seminiferous epithelium and restored spermatogenesis and fertility in 50% of previously infertile mutants. Our findings indicate that SMS1 has a wider than anticipated role in testis polyunsaturated fatty acid homeostasis and for male fertility.

  20. Cellulose synthases: new insights from crystallography and modeling.

    Science.gov (United States)

    Slabaugh, Erin; Davis, Jonathan K; Haigler, Candace H; Yingling, Yaroslava G; Zimmer, Jochen

    2014-02-01

    Detailed information about the structure and biochemical mechanisms of cellulose synthase (CelS) proteins remained elusive until a complex containing the catalytic subunit (BcsA) of CelS from Rhodobacter sphaeroides was crystalized. Additionally, a 3D structure of most of the cytosolic domain of a plant CelS (GhCESA1 from cotton, Gossypium hirsutum) was produced by computational modeling. This predicted structure contributes to our understanding of how plant CelS proteins may be similar and different as compared with BcsA. In this review, we highlight how these structures impact our understanding of the synthesis of cellulose and other extracellular polysaccharides. We show how the structures can be used to generate hypotheses for experiments testing mechanisms of glucan synthesis and translocation in plant CelS. Copyright © 2013 Elsevier Ltd. All rights reserved.

  1. Two Cycloartenol Synthases for Phytosterol Biosynthesis in Polygala tenuifolia Willd.

    Science.gov (United States)

    Jin, Mei Lan; Lee, Woo Moon; Kim, Ok Tae

    2017-11-15

    Oxidosqualene cyclases (OSCs) are enzymes that play a key role in control of the biosynthesis of phytosterols and triterpene saponins. In order to uncover OSC genes from Polygala tenuifolia seedlings induced by methyl jasmonate (MeJA), RNA-sequencing analysis was performed using the Illumina sequencing platform. A total of 148,488,632 high-quality reads from two samples (control and the MeJA treated) were generated. We screened genes related to phytosterol and triterpene saponin biosynthesis and analyzed the transcriptional changes of differentially expressed unigene (DEUG) values calculated by fragments per kilobase million (FPKM). In our datasets, two full-length cDNAs of putative OSC genes, PtCAS1 , and PtCAS2 , were found, in addition to the PtBS (β-amyrin synthase) gene reported in our previous studies and the two cycloartenol synthase genes of P. tenuifolia . All genes were isolated and characterized in yeast cells. The functional expression of the two PtCAS genes in yeast cells showed that the genes all produce a cycloartenol as the sole product. When qRT-PCR analysis from different tissues was performed, the expressions of PtCAS1 and PtCAS2 were highest in flowers and roots, respectively. After MeJA treatment, the transcripts of PtCAS1 and PtCAS2 genes increased by 1.5- and 2-fold, respectively. Given these results, we discuss the potential roles of the two PtCAS genes in relation to triterpenoid biosynthesis.

  2. Two Cycloartenol Synthases for Phytosterol Biosynthesis in Polygala tenuifolia Willd

    Directory of Open Access Journals (Sweden)

    Mei Lan Jin

    2017-11-01

    Full Text Available Oxidosqualene cyclases (OSCs are enzymes that play a key role in control of the biosynthesis of phytosterols and triterpene saponins. In order to uncover OSC genes from Polygala tenuifolia seedlings induced by methyl jasmonate (MeJA, RNA-sequencing analysis was performed using the Illumina sequencing platform. A total of 148,488,632 high-quality reads from two samples (control and the MeJA treated were generated. We screened genes related to phytosterol and triterpene saponin biosynthesis and analyzed the transcriptional changes of differentially expressed unigene (DEUG values calculated by fragments per kilobase million (FPKM. In our datasets, two full-length cDNAs of putative OSC genes, PtCAS1, and PtCAS2, were found, in addition to the PtBS (β-amyrin synthase gene reported in our previous studies and the two cycloartenol synthase genes of P. tenuifolia. All genes were isolated and characterized in yeast cells. The functional expression of the two PtCAS genes in yeast cells showed that the genes all produce a cycloartenol as the sole product. When qRT-PCR analysis from different tissues was performed, the expressions of PtCAS1 and PtCAS2 were highest in flowers and roots, respectively. After MeJA treatment, the transcripts of PtCAS1 and PtCAS2 genes increased by 1.5- and 2-fold, respectively. Given these results, we discuss the potential roles of the two PtCAS genes in relation to triterpenoid biosynthesis.

  3. The evolution of function in strictosidine synthase-like proteins.

    Science.gov (United States)

    Hicks, Michael A; Barber, Alan E; Giddings, Lesley-Ann; Caldwell, Jenna; O'Connor, Sarah E; Babbitt, Patricia C

    2011-11-01

    The exponential growth of sequence data provides abundant information for the discovery of new enzyme reactions. Correctly annotating the functions of highly diverse proteins can be difficult, however, hindering use of this information. Global analysis of large superfamilies of related proteins is a powerful strategy for understanding the evolution of reactions by identifying catalytic commonalities and differences in reaction and substrate specificity, even when only a few members have been biochemically or structurally characterized. A comparison of >2500 sequences sharing the six-bladed β-propeller fold establishes sequence, structural, and functional links among the three subgroups of the functionally diverse N6P superfamily: the arylesterase-like and senescence marker protein-30/gluconolactonase/luciferin-regenerating enzyme-like (SGL) subgroups, representing enzymes that catalyze lactonase and related hydrolytic reactions, and the so-called strictosidine synthase-like (SSL) subgroup. Metal-coordinating residues were identified as broadly conserved in the active sites of all three subgroups except for a few proteins from the SSL subgroup, which have been experimentally determined to catalyze the quite different strictosidine synthase (SS) reaction, a metal-independent condensation reaction. Despite these differences, comparison of conserved catalytic features of the arylesterase-like and SGL enzymes with the SSs identified similar structural and mechanistic attributes between the hydrolytic reactions catalyzed by the former and the condensation reaction catalyzed by SS. The results also suggest that despite their annotations, the great majority of these >500 SSL sequences do not catalyze the SS reaction; rather, they likely catalyze hydrolytic reactions typical of the other two subgroups instead. This prediction was confirmed experimentally for one of these proteins. Copyright © 2011 Wiley-Liss, Inc.

  4. Intestinal nitric oxide synthase activity changes during experimental colon obstruction.

    Science.gov (United States)

    Palásthy, Zsolt; Kaszaki, József; Lázár, György; Nagy, Sándor; Boros, Mihály

    2006-08-01

    The experiments in this study were designed to follow the time course of nitric oxide (NO) synthesis in the large bowel during acute mechanical ileus. Occlusion of the mid-transverse colon was maintained for 420 min in anesthetized dogs. Strain-gauge transducers were used to analyze motility changes on the hepatic and lienal flexures, respectively. Constitutive NO synthase (cNOS) and inducible NOS (iNOS) activities were determined in tissue biopsies, and plasma nitrite/nitrate (NOx) level was measured in the portal blood. Following completion of the baseline studies, the animals were treated with either 7-nitroindazole (7-NI, selective neuronal NOS inhibitor), or N-nitro-L-arginine (NNA, non-selective NOS inhibitor). In the sham-operated group the cNOS activities differed significantly in the oral and aboral tissue samples (oral: 102.9; versus aboral: 62.1 fmol/mg protein/min). The obstruction elicited a significant increase in portal NOx and elevated tissue inducible NO synthase (iNOS) activity. NNA treatment decreased the motility index in both intestinal segments for 60 min, but 120 min later the motility index was significantly elevated (2.5-fold increase in the oral part, and 1.8-fold enhancement in the aboral segment, respectively). Treatment with 7-NI decreased the cNOS activity in the oral and aboral parts by approximately 40% and 70%, respectively, and suppressed the motility increase in the aboral colon segment. The motility of the colon was either significantly increased or decreased, depending on the type and selectivity of the NOS inhibitor compounds applied. NO of neuronal origin is a transmitter that stimulates peristaltic activity; but an increased iNOS/nNOS ratio significantly moderates the obstruction-induced motility increase.

  5. Glycogen Synthase in Sertoli Cells: More Than Glycogenesis?

    Science.gov (United States)

    Maldonado, Rodrigo; Mancilla, Héctor; Villarroel-Espíndola, Franz; Slebe, Felipe; Slebe, Juan Carlos; Méndez, Raúl; Guinovart, Joan J; Concha, Ilona I

    2016-11-01

    Sertoli cell metabolism actively maintains the nutritional needs of germ cells. It has been described that after glucose incorporation in Sertoli cells, less than 1% is converted to glycogen suggesting low levels of glycogen synthase activity. Phosphorylation of muscle glycogen synthase (MGS) at serine 640 (pS640MGS) decreases its activity, and this form of the enzyme was discovered as a non-ribosomal protein that modulates the translation of a subset of transcripts in HeLa cells. The aim of our study was to functionally characterize MGS in cultured Sertoli cells, as well as to explore this new feature related to RNA molecules. We detected MGS in the cytoplasm of Sertoli cells as well as in the nuclei. The activity rates of the enzyme were extremely low indicating that MGS is expressed but almost inactive. Protein targeting to glycogen (PTG) overexpression was performed to activate MGS by dephosphorylation. PTG induced glycogen synthesis massively, confirming that this enzyme is present but inactive. This finding correlates with high levels of pS640MGS, which were assayed by phosphatase treatment. To explore a putative new function for MGS in Sertoli cells, we performed RNA immunoprecipitation coupled to microarray studies. The results revealed that MGS co-immunoprecipitated with the several mRNAs and also rRNAs. These findings indicate that MGS is expressed Sertoli cells but in an inactive form, and also support a possibly novel feature of this metabolic enzyme associated with RNA-related molecules. J. Cell. Biochem. 117: 2597-2607, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  6. Mutational, Phylogeny and Evolution Analyses of Salvia Copalyl Diphosphate Synthase

    International Nuclear Information System (INIS)

    Hao, D. C.; Thimmappa, R. B.; Xiao, P. G.

    2016-01-01

    The cyclization of geranylgeranyl diphosphate (GGPP) is catalyzed by copalyl diphosphate synthase (CPS), a class II diterpene synthase (diTPS), to form copalyl diphosphate (CPP), which is an essential substrate of a variety of diterpenes in secondary metabolism of angiosperm including Salvia medicinal plants. The protein environment of the N-terminal class II active site stabilizes the carbocation intermediates and maintains the catalytic activity of angiosperm class II diTPS. The virtual modeling and mutagenesis of the class II diTPS of Salvia miltiorrhiza (SmCPS) were accomplished to illuminate the catalytic activity of SmCPS. Terminal truncations and point mutations established the role of the Beta-Gamma domain and Alpha domain, i.e., they facilitate the flexible conformational change of the class II active site after substrate binding. E203 and K238 in the N-ter Gamma domain of SmCPS1 are functional in the substrate binding and conformational transition and might be essential in catalysis. Similar to other CPSs, the ensuing protonation of the GGPP substrate and coordination of the diphosphate group are governed by highly conserved residues in the DxDD motif of SmCPS, e.g., D372 of CPS1. Moreover, F256 and Y505 stabilize the carbocation and control the enzymatic activity during CPP formation. The amino acids of the predicted active sites, despite under purifying selection, vary greatly, corresponding to the functional flexibility of angiosperm CPSs. Molecular phylogeny and evolution analyses suggest early and ongoing evolution of labdane-related diterpenoid metabolism in angiosperm. (author)

  7. Isolation and functional effects of monoclonal antibodies binding to thymidylate synthase.

    Science.gov (United States)

    Jastreboff, M M; Todd, M B; Malech, H L; Bertino, J R

    1985-01-29

    Monoclonal antibodies against electrophoretically pure thymidylate synthase from HeLa cells have been produced. Antibodies (M-TS-4 and M-TS-9) from hybridoma clones were shown by enzyme-linked immunoassay to recognize thymidylate synthase from a variety of human cell lines, but they did not bind to thymidylate synthase from mouse cell lines. The strongest binding of antibodies was observed to enzyme from HeLa cells. These two monoclonal antibodies bind simultaneously to different antigenic sites on thymidylate synthase purified from HeLa cells, as reflected by a high additivity index and results of cross-linked radioimmunoassay. Both monoclonal antibodies inhibit the activity of thymidylate synthase from human cell lines. The strongest inhibition was observed with thymidylate synthase from HeLa cells. Monoclonal antibody M-TS-9 (IgM subclass) decreased the rate of binding of [3H]FdUMP to thymidylate synthase in the presence of 5,10-methylenetetrahydrofolate while M-TS-4 (IgG1) did not change the rate of ternary complex formation. These data indicate that the antibodies recognize different epitopes on the enzyme molecule.

  8. Nanoscale Soldering of Positioned Carbon Nanotubes using Highly Conductive Electron Beam Induced Gold Deposition

    DEFF Research Database (Denmark)

    Madsen, Dorte Nørgaard; Mølhave, Kristian; Mateiu, Ramona Valentina

    2003-01-01

    We have developed an in-situ method for controlled positioning of carbon nanotubes followed by highly conductive contacting of the nanotubes, using electron beam assisted deposition of gold. The positioning and soldering process takes place inside an Environmental Scanning Electron Microscope (E...... in a carbon matrix. Nanoscale soldering of multi-walled carbon nanotubes (MWNT) onto microelectrodes was achieved by deposition of a conducting gold line across a contact point between nanotube and electrode. The solderings were found to be mechanically stronger than the carbon nanotubes. We have positioned...... MWNTs to bridge the gap between two electrodes, and formed soldering bonds between the tube and each of the electrodes. All nanotube bridges showed ohmic resistances in the range 10-30 kΩ. We observed no increase in resistance after exposing the MWNT bridge to air for days....

  9. Systematic replacement of lysine with glutamine and alanine in Escherichia coli malate synthase G: effect on crystallization

    International Nuclear Information System (INIS)

    Anstrom, David M.; Colip, Leslie; Moshofsky, Brian; Hatcher, Eric; Remington, S. James

    2005-01-01

    Alanine and glutamine mutations were made to the same 15 lysine positions on the surface of E. coli malate synthase G and the impact on crystallization observed. The results support lysine replacement for improvement of crystallization and provide insight into site selection and type of amino-acid replacement. Two proposals recommend substitution of surface lysine residues as a means to improve the quality of protein crystals. In proposal I, substitution of lysine by alanine has been suggested to improve crystallization by reducing the entropic cost of ordering flexible side chains at crystal contacts. In proposal II, substitution of lysine by residues more commonly found in crystal contacts, such as glutamine, has been proposed to improve crystallization. 15 lysine residues on the surface of Escherichia coli malate synthase G, distributed over a variety of secondary structures, were individually mutated to both alanine and glutamine. For 28 variants, detailed studies of the effect on enzymatic activity and crystallization were conducted. This has permitted direct comparison of the relative effects of the two types of mutations. While none of the variants produced crystals suitable for X-ray structural determination, small crystals were obtained in a wide variety of conditions, in support of the general approach. Glutamine substitutions were found to be more effective than alanine in producing crystals, in support of proposal II. Secondary structure at the site of mutation does not appear to play a major role in determining the rate of success

  10. Structure of the dimeric form of CTP synthase from Sulfolobus solfataricus

    DEFF Research Database (Denmark)

    Lauritsen, Iben; Willemoës, Martin; Jensen, Kaj Frank

    2011-01-01

    CTP synthase catalyzes the last committed step in de novo pyrimidine-nucleotide biosynthesis. Active CTP synthase is a tetrameric enzyme composed of a dimer of dimers. The tetramer is favoured in the presence of the substrate nucleotides ATP and UTP; when saturated with nucleotide, the tetramer...... completely dominates the oligomeric state of the enzyme. Furthermore, phosphorylation has been shown to regulate the oligomeric states of the enzymes from yeast and human. The crystal structure of a dimeric form of CTP synthase from Sulfolobus solfataricus has been determined at 2.5 Å resolution...

  11. Nerve conduction velocity

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/003927.htm Nerve conduction velocity To use the sharing features on this page, please enable JavaScript. Nerve conduction velocity (NCV) is a test to see ...

  12. Conducting Polymeric Materials

    DEFF Research Database (Denmark)

    Hvilsted, Søren

    2016-01-01

    The overall objective of this collection is to provide the most recent developments within the various areas of conducting polymeric materials. The conductivity of polymeric materials is caused by electrically charged particles, ions, protons and electrons. Materials in which electrons...

  13. Space charge limited current conduction in Bi2Te3 thin films

    International Nuclear Information System (INIS)

    Sathyamoorthy, R.; Dheepa, J.; Velumani, S.

    2007-01-01

    Bi 2 Te 3 is known for its large thermoelectric coefficients and is widely used as a material for Peltier devices. Bi 2 Te 3 thin films with thicknesses in the range 125-300 A have been prepared by Flash Evaporation at a pressure of 10 -5 m bar on clean glass substrates at room temperature. An Al-Bi 2 Te 3 -Al sandwich structure has been used for electrical conduction properties in the temperature range 303 to 483 K. I-V characteristics showed Ohmic conduction in the low voltage region. In the higher voltage region, a Space Charge Limited Conduction (SCLC) takes place due to the presence of the trapping level. The transition voltage (V t ), between the Ohmic and the SCLC condition was proportional to the square of thickness. Further evidence for this conduction process was provided by the linear dependence of V t on t 2 and log J on log t. The hole concentration in the films were found to be n 0 = 1.65 * 10 10 m -3 . The carrier mobility increases with increasing temperature whereas the density of trapped charges decreases with increasing temperature. The barrier height decreases with an increase in temperature. The increase in the trapping concentration V t is correlated with ascending the degree of preferred orientation of the highest atomic density plane. The activation energy was estimated and the values found to decrease with increasing applied voltage. The zero field value of the activation energy is found to be 0.4 eV

  14. Application of a Colorimetric Assay to Identify Putative Ribofuranosylaminobenzene 5'-Phosphate Synthase Genes Expressed with Activity in Escherichia coli

    Directory of Open Access Journals (Sweden)

    Bechard Matthew E.

    2003-01-01

    Full Text Available Tetrahydromethanopterin (H4MPT is a tetrahydrofolate analog originally discovered in methanogenic archaea, but later found in other archaea and bacteria. The extent to which H4MPT occurs among living organisms is unknown. The key enzyme which distinguishes the biosynthetic pathways of H4MPT and tetrahydrofolate is ribofuranosylaminobenzene 5'-phosphate synthase (RFAP synthase. Given the importance of RFAP synthase in H4MPT biosynthesis, the identification of putative RFAP synthase genes and measurement of RFAP synthase activity would provide an indication of the presence of H4MPT in untested microorganisms. Investigation of putative archaeal RFAP synthase genes has been hampered by the tendency of the resulting proteins to form inactive inclusion bodies in Escherichia coli. The current work describes a colorimetric assay for measuring RFAP synthase activity, and two modified procedures for expressing recombinant RFAP synthase genes to produce soluble, active enzyme. By lowering the incubation temperature during expression, RFAP synthase from Archaeoglobus fulgidus was produced in E. coli and purified to homogeneity. The production of active RFAP synthase from Methanothermobacter thermautotrophicus was achieved by coexpression of the gene MTH0830 with a molecular chaperone. This is the first direct biochemical identification of a methanogen gene that codes for an active RFAP synthase.

  15. Application of a Colorimetric Assay to Identify Putative Ribofuranosylaminobenzene 5'-Phosphate Synthase Genes Expressed with Activity in Escherichia coli.

    Science.gov (United States)

    Bechard, Matthew E.; Chhatwal, Sonya; Garcia, Rosemarie E.; Rasche, Madeline E.

    2003-01-01

    Tetrahydromethanopterin (H(4)MPT) is a tetrahydrofolate analog originally discovered in methanogenic archaea, but later found in other archaea and bacteria. The extent to which H(4)MPT occurs among living organisms is unknown. The key enzyme which distinguishes the biosynthetic pathways of H(4)MPT and tetrahydrofolate is ribofuranosylaminobenzene 5'-phosphate synthase (RFAP synthase). Given the importance of RFAP synthase in H(4)MPT biosynthesis, the identification of putative RFAP synthase genes and measurement of RFAP synthase activity would provide an indication of the presence of H(4)MPT in untested microorganisms. Investigation of putative archaeal RFAP synthase genes has been hampered by the tendency of the resulting proteins to form inactive inclusion bodies in Escherichia coli. The current work describes a colorimetric assay for measuring RFAP synthase activity, and two modified procedures for expressing recombinant RFAP synthase genes to produce soluble, active enzyme. By lowering the incubation temperature during expression, RFAP synthase from Archaeoglobus fulgidus was produced in E. coli and purified to homogeneity. The production of active RFAP synthase from Methanothermobacter thermautotrophicus was achieved by coexpression of the gene MTH0830 with a molecular chaperone. This is the first direct biochemical identification of a methanogen gene that codes for an active RFAP synthase.

  16. Electrically conductive composite material

    Science.gov (United States)

    Clough, Roger L.; Sylwester, Alan P.

    1989-01-01

    An electrically conductive composite material is disclosed which comprises a conductive open-celled, low density, microcellular carbon foam filled with a non-conductive polymer or resin. The composite material is prepared in a two-step process consisting of first preparing the microcellular carbon foam from a carbonizable polymer or copolymer using a phase separation process, then filling the carbon foam with the desired non-conductive polymer or resin. The electrically conductive composites of the present invention has a uniform and consistant pattern of filler distribution, and as a result is superior over prior art materials when used in battery components, electrodes, and the like.

  17. Operation of ohmic Ti/Al/Pt/Au multilayer contacts to GaN at 600 °C in air

    Science.gov (United States)

    Hou, Minmin; Senesky, Debbie G.

    2014-08-01

    The high-temperature characteristics (at 600 °C) of Ti/Al/Pt/Au multilayer contacts to gallium nitride (GaN) in air are reported. Microfabricated circular-transfer-line-method test structures were subject to 10 h of thermal storage at 600 °C. Intermittent electrical characterization during thermal storage showed minimal variation in the contact resistance after 2 h and that the specific contact resistivity remained on the order of 10-5 Ω-cm2. In addition, the thermally stored multilayer contacts to GaN showed ohmic I-V characteristics when electrically probed at 600 °C. The microstructural analysis with atomic force microscopy showed minimal changes in surface roughness after thermal storage. Observations of the thermochemical reactions after thermal storage using Auger electron spectroscopy chemical depth profiling showed diffusion of Pt and minimal additional Al oxidation. The results support the use of Ti/Al/Pt/Au multilayer metallization for GaN-based sensors and electronic devices that will operate within a high-temperature and oxidizing ambient.

  18. Lifetime limitations of ohmic, contacting RF MEMS switches with Au, Pt and Ir contact materials due to accumulation of ‘friction polymer’ on the contacts

    International Nuclear Information System (INIS)

    Czaplewski, David A; Nordquist, Christopher D; Dyck, Christopher W; Patrizi, Gary A; Kraus, Garth M; Cowan, William D

    2012-01-01

    We present lifetime limitations and failure analysis of many packaged RF MEMS ohmic contacting switches with Au–Au, Au–Ir, and Au–Pt contact materials operating with 100 µN of contact force per contact in hermetically sealed glass wall packages. All metals were tested using the same switch design in a controlled environment to provide a comparison between the performance of the different materials and their corresponding failure mechanisms. The switch lifetimes of the different contact materials varied from several hundred cycles to 200 million cycles with different mechanisms causing failures for different contact materials. Switches with Au–Au contacts failed due to adhesion when thoroughly cleaned while switches with dissimilar metal contacts (Au–Ir and Au–Pt) operated without adhesion failures but failed due to carbon accumulation on the contacts even in a clean, packaged environment as a result of the catalytic behavior of the contact materials. Switch lifetimes correlated inversely with catalytic behavior of the contact metals. The data suggests the path to increase switch lifetime is to use favorable catalytic materials as contacts, design switches with higher contact forces to break through any residual contamination, and use cleaner, probably smaller, packages. (paper)

  19. Design and experimental results of feedback control of Ohmic-heating transformer magnetic flux by LHCD power in HT-7 Tokamak

    International Nuclear Information System (INIS)

    Yiyun Huang

    2006-01-01

    In order to make a research on long pulse or even steady state operation with non-inductive drive in plasma discharge, a new feedback control scheme instead of the previous one has been designed and operated in HT-7 [HT-7 team presented by J. Li, et al., Plasma Phys. Control. Fusion 42 (2) (2000) 135-146] Tokamak experiment, 2004. Consumption of iron-core transformer magnetic flux (MFT) is feedback controlled for the first time by power of lower hybrid current drive (LHCD) P LH , when the Ohmic-heating circuit current can maintain the plasma current I P constant with another feedback control loop, which make MFT evolve at alternating-change state to avoid flux saturation. Plasma current I P can be maintained steadily up to 120s in this operation mode at reduced plasma parameters (I P ∼50-100KA, average density n-bar e =0.4-0.5x10 19 m -3 , P LH =100-200KW). Design and experimental results are presented in the paper, which including control model analysis, configurations of control system and MFT feedback control experiments in HT-7. The high voltage power supply (HVPS) of LHCD is the main controller that regulates the LHCD power into the plasma to control the MFT

  20. Thermal degradation of ohmic contacts on semipolar (11-22) GaN films grown on m-plane (1-100) sapphire substrates

    International Nuclear Information System (INIS)

    Kim, Doo Soo; Kim, Deuk Young; Seo, Yong Gon; Kim, Ji Hoon; Hwang, Sung Min; Baik, Kwang Hyeon

    2012-01-01

    Semipolar (11-22) GaN films were grown on m-plane (1-100) sapphire substrates by using metalorganic chemical vapor deposition. The line widths of the omega rocking curves of the semipolar GaN films were 498 arcsec along the [11-23] GaN direction and 908 arcsec along the [10-10] GaN direction. The properties of the Ti/Al/Ni/Au metal contact were investigated using transmission-line-method patterns oriented in both the [11-23] GaN and the [10-10] GaN directions of semipolar (11-22) GaN. The minimum specific contact resistance of ∼3.6 x 10 -4 Ω·cm -2 was obtained on as-deposited metal contacts. The Ohmic contact properties of semipolar (11-22) GaN became degraded with increasing annealing temperature above 400 .deg. C. The thermal degradation of the metal contacts may be attributed to the surface property of N-polarity on the semipolar (11-22) GaN films. Also, the semipolar (11-22) GaN films did not show clear anisotropic behavior of the electrical properties for different azimuthal angles.

  1. Effect of the non-annealed ohmic-recess approach on temperature-dependent properties of a metamorphic high electron mobility transistor

    International Nuclear Information System (INIS)

    Chen, Li-Yang; Tsai, Tsung-Han; Chen, Tzu-Pin; Liu, Yi-Chun; Liu, Wen-Chau; Cheng, Shiou-Ying; Lour, Wen-Shiung; Tsai, Jung-Hui; Guo, Der-Feng

    2008-01-01

    The reliability-related properties of an InAlAs/InGaAs metamorphic high electron mobility transistor (MHEMT), using the non-annealed ohmic-recess (NAOR) approach, are studied and demonstrated. The NAOR device shows significantly improved dc and radio frequency (RF) performance over a wide temperature range (300–500 K). With a 1 × 100 µm 2 gate-dimension MHEMT by the NAOR approach, the considerably improved thermal stability and dc performances, including lower temperature variation coefficients on turn-on voltage (−1.38 mV K −1 ) and gate-drain breakdown voltage (−30.4 mV K −1 ), and on-resistance (2.41 × 10 −3 Ω mm K −1 ), are obtained as the temperature is increased from 300 to 500 K. For RF characteristics, the NAOR device also shows a low degradation rate on drain saturation current operating regimes (−5.52 × 10 −4 K −1 ) as the temperature is increased from 300 to 400 K. In addition, based on the lifetime tests, an activation energy of 1.33 eV and a projected median lifetime of 1.2 × 10 7 h at T ch = 125 °C are obtained for the NAOR MHEMT

  2. Variational dynamics of the sub-Ohmic spin-boson model on the basis of multiple Davydov D{sub 1} states

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Lu [Division of Materials Science, Nanyang Technological University, Singapore 639798 (Singapore); Department of Physics, Zhejiang University, Hangzhou 310027 (China); Chen, Lipeng; Zhao, Yang, E-mail: YZhao@ntu.edu.sg [Division of Materials Science, Nanyang Technological University, Singapore 639798 (Singapore); Zhou, Nengji [Department of Physics, Hangzhou Normal University, Hangzhou 310046 (China)

    2016-01-14

    Dynamics of the sub-Ohmic spin-boson model is investigated by employing a multitude of the Davydov D{sub 1} trial states, also known as the multi-D{sub 1} Ansatz. Accuracy in dynamics simulations is improved significantly over the single D{sub 1} Ansatz, especially in the weak system-bath coupling regime. The reliability of the multi-D{sub 1} Ansatz for various coupling strengths and initial conditions is also systematically examined, with results compared closely with those of the hierarchy equations of motion and the path integral Monte Carlo approaches. In addition, a coherent-incoherent phase crossover in the nonequilibrium dynamics is studied through the multi-D{sub 1} Ansatz. The phase diagram is obtained with a critical point s{sub c} = 0.4. For s{sub c} < s < 1, the coherent-to-incoherent crossover occurs at a certain coupling strength, while the coherent state recurs at a much larger coupling strength. For s < s{sub c}, only the coherent phase exists.

  3. Target-site resistance to acetolactate synthase (ALS)-inhibiting herbicides in Amaranthus palmeri from Argentina.

    Science.gov (United States)

    Larran, Alvaro S; Palmieri, Valeria E; Perotti, Valeria E; Lieber, Lucas; Tuesca, Daniel; Permingeat, Hugo R

    2017-12-01

    Herbicide-resistant weeds are a serious problem worldwide. Recently, two populations of Amaranthus palmeri with suspected cross-resistance to acetolactate synthase (ALS)-inhibiting herbicides (R1 and R2) were found by farmers in two locations in Argentina (Vicuña Mackenna and Totoras, respectively). We conducted studies to confirm and elucidate the mechanism of resistance. We performed in vivo dose-response assays, and confirmed that both populations had strong resistance to chlorimuron-ethyl, diclosulam and imazethapyr when compared with a susceptible population (S). In vitro ALS activity inhibition tests only indicated considerable resistance to imazethapyr and chlorimuron-ethyl, indicating that other non-target mechanisms could be involved in diclosulam resistance. Subsequently, molecular analysis of als nucleotide sequences revealed three single base-pair mutations producing substitutions in amino acids previously associated with resistance to ALS inhibitors, A122, W574, and S653. This is the first report of als resistance alleles in A. palmeri in Argentina. The data support the involvement of a target-site mechanism of resistance to ALS-inhibiting herbicides. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  4. Endothelial nitric oxide synthase deficiency influences normal cell cycle progression and apoptosis in trabecular meshwork cells

    Directory of Open Access Journals (Sweden)

    Qiong Liao

    2016-06-01

    Full Text Available AIM: To clarify how the endothelial nitric oxide synthase (eNOS, NOS3 make effect on outflow facility through the trabecular meshwork (TM. METHODS: Inhibition of NOS3 gene expression in human TM cells were conducted by three siRNAs. Then the mRNA and protein levels of NOS3 in siRNA-treated and negative control (NC cells were determined, still were the collagen, type IV, alpha 1 (COL4A1 and fibronectin 1 by real-time PCR and Western blot analysis. In addition, NOS3 concentrations in culture supernatant fluids of TM cells were measured. Cell cycle and cell apoptosis analysis were performed using flow cytometry. RESULTS: The mRNA level of NOS3 was decreased by three different siRNA interference, similar results were obtained not only of the relative levels of NOS3 protein, but also the expression levels of COL4A1 and fibronectin 1. The number of cells in S phase was decreased, while contrary result was obtained in G2 phase. The number of apoptotic cells in siRNA-treated groups were significant increased compared to the NC samples. CONCLUSION: Abnormal NOS3 expression can make effects on the proteins levels of extracellular matrix component (e.g. fibronectin 1 and COL4A1. Reduced NOS3 restrains the TM cell cycle progression at the G2/M-phase transition and induced cell apoptosis.

  5. Chronic inhibition of nitric oxide synthase augments the ACTH response to exercise.

    Science.gov (United States)

    Jankord, Ryan; McAllister, Richard M; Ganjam, Venkataseshu K; Laughlin, M Harold

    2009-03-01

    Exercise can activate the hypothalamo-pituitary-adrenocortical (HPA) axis, and regular exercise training can impact how the HPA axis responds to stress. The mechanism by which acute exercise induces HPA activity is unclear. Therefore, the purpose of this study was to test the hypothesis that nitric oxide modulates the neuroendocrine component of the HPA axis during exercise. Female Yucatan miniature swine were treated with N-nitro-l-arginine methyl ester (l-NAME) to test the effect of chronic nitric oxide synthase (NOS) inhibition on the ACTH response to exercise. In addition, we tested the effect of NOS inhibition on blood flow to tissues of the HPA axis and report the effects of handling and treadmill exercise on the plasma concentrations of ACTH and cortisol. Chronic NOS inhibition decreased plasma NO(x) levels by 44%, increased mean arterial blood pressure by 46%, and increased expression of neuronal NOS in carotid arteries. Vascular conductance was decreased in the frontal cortex, the hypothalamus, and the adrenal gland. Chronic NOS inhibition exaggerated the ACTH response to exercise. In contrast, chronic NOS inhibition decreased the ACTH response to restraint, suggesting that the role of NO in modulating HPA activity is stressor dependent. These results demonstrate that NOS activity modulates the response of the neuroendocrine component of the HPA axis during exercise stress.

  6. Scanning electrochemical microscopy for the fabrication of copper nanowires: Atomic contacts with quantized conductance, and molecular adsorption effect

    International Nuclear Information System (INIS)

    Janin, Marion; Ghilane, Jalal; Lacroix, Jean-Christophe

    2012-01-01

    Highlights: ► Electrochemistry and SECM to generate copper nanowires with quantized conductance. ► Stable atomic contacts lasting for several hundreds of seconds have been obtained. ► The quantized conductances are independent of the tip and gap size. ► The method allows contacts to be generated in the presence of chosen molecules. ► Four-electrode configuration opens the route to redox gated atomic contact. - Abstract: Scanning electrochemical microscopy, SECM, is proposed as a tool for the fabrication of copper nanowires. In a first step, configuration based on two electrodes, a platinum UME (cathode) and a copper substrate (anode), operating in the SECM configuration was employed. For nanowires generated in water the conductance changes stepwise and varies by integer values of the conductance quantum G 0 . The formation of atomic contacts is supported by the ohmic behavior of the I–V curve. It depends neither on the UME tip radius nor on the initial gap size between tip and substrate. Atomic contacts generated in aqueous solutions of sodium dodecyl sulfate (SDS) below the critical micellar concentration (CMC) have conductances below 1G 0 attributed to molecular adsorption on the contact. In some cases, the nanowires have low conductance, 0.01G 0 . The corresponding I–V curve shows tunneling rather than ohmic behavior, suggesting that molecular junctions are formed with a few surfactant molecules trapped between the two electrodes. Finally, copper nanowires with quantized conductance have been generated using the SECM operating in a four-electrode setup. Thanks to the reference electrode, this configuration leads to better control of the potential of each working electrode; this setup will make it possible to evaluate the conductance variation and/or modulation upon electrochemical stimuli.

  7. Molecular size estimation of plasma membrane β-glucan synthase from red beet root

    International Nuclear Information System (INIS)

    Sloan, M.E.; Eiberger, L.L.; Wasserman, B.P.

    1986-01-01

    Cellulose and cell wall β-D-glucans in higher plants are thought to be synthesized by the plasma membrane enzyme, β-glucan synthase. This enzyme has never been purified to homogeneity, hence its subunit composition is unknown. Partial purification of red beet root glucan synthase by glycerol density gradient centrifugation followed by SDS-PAGE yielded a highly enriched subunit of 68 kDa. Radiation inactivation of plasma membranes gave a molecular size the 450 kDa for the holoenzyme complex. This suggests that glucan synthase consists of 6 to 7 subunits and confirms electron microscope studies showing that glucan synthases exist as multi-subunit complexes embedded within the membrane

  8. SCREENING OF 6-PYRUVOYL-TETRAHYDROPTERIN SYNTHASE ACTIVITY DEFICIENCY AMONG HYPERP HENYLALANINEMIC PATIENTS

    Directory of Open Access Journals (Sweden)

    DURDI QUJEQ

    1999-10-01

    Full Text Available A deficiency of the phenylalanine hydroxylase activity or its cofactor tetrahydrobiopterin may"nlead to hyperphenylalamnemia and as a result, loss of IQ, poor school performance, and"nbehavior problems occurs. Deficiency in 6-pyruvoyl-tetrahydropterin synthase activity is the"nmajor cause of tetrahydrobiopterin deficient phenylketonuria. In this study, blood specimens"nfrom 165 healthy volunteers and 127 children with phenylketonuria were used to determine"nthe 6-pyruvoyl-tetrahydropterin synthase activity. It was found that the activity of 6-"npyruvoyl- tetrahydropterin synthase was decreased in comparison with control [23.46 +/-"n2.94, (mean +/- SD, mmol/ ml/h, n=I27 vs. 127.63 +/- 4.52, n=165, p<0.05]. Results of"nthis study indicate that examination of 6-pyruvoyl-tetrahydropterin synthase activity is helpful"nand may lead to the diagnosis cause of hyperphenylalaninemia.

  9. Mechanical Control of ATP Synthase Function: Activation Energy Difference between Tight and Loose Binding Sites

    KAUST Repository

    Beke-Somfai, Tamás; Lincoln, Per; Nordén, Bengt

    2010-01-01

    Despite exhaustive chemical and crystal structure studies, the mechanistic details of how FoF1-ATP synthase can convert mechanical energy to chemical, producing ATP, are still not fully understood. On the basis of quantum mechanical calculations

  10. Eukaryotic beta-alanine synthases are functionally related but have a high degree of structural diversity

    DEFF Research Database (Denmark)

    Gojkovic, Zoran; Sandrini, Michael; Piskur, Jure

    2001-01-01

    no pyrimidine catabolic pathway, it enabled growth on N-carbamyl- beta -alanine as the sole nitrogen source. The D. discoideum and D. melanogaster PYD3 gene products are similar to mammalian beta -alanine synthases. In contrast, the S. kluyveri protein is quite different from these and more similar to bacterial......beta -Alanine synthase (EC 3.5.1.6), which catalyzes the final step of pyrimidine catabolism, has only been characterized in mammals. A Saccharomyces kluyveri pyd3 mutant that is unable to grow on N-carbamy-beta -alanine as the sole nitrogen source and exhibits diminished beta -alanine synthase...... N- carbamyl amidohydrolases. All three beta -alanine synthases are to some degree related to various aspartate transcarbamylases, which catalyze the second step of the de novo pyrimidine biosynthetic pathway. PYD3 expression in yeast seems to be inducible by dihydrouracil and N...

  11. Citric acid production and citrate synthase genes in distinct strains of ...

    African Journals Online (AJOL)

    SAM

    2014-05-28

    May 28, 2014 ... synthase in lactic acid production by A. niger and with the ... A number of microorganisms, including both bacteria and fungi, possess the capacity ..... citric acid production by solid-state fermentation from cassava bagasse and ...

  12. Structure of an RNA dimer of a regulatory element from human thymidylate synthase mRNA

    OpenAIRE

    Dibrov, Sergey; McLean, Jaime; Hermann, Thomas

    2011-01-01

    An oligonucleotide representing a regulatory element of human thymidylate synthase mRNA has been crystallized as a dimer. The structure of the asymmetric dimer has been determined at 1.97 Å resolution.

  13. Seasonal influence on gene expression of monoterpene synthases in Salvia officinalis (Lamiaceae).

    Science.gov (United States)

    Grausgruber-Gröger, Sabine; Schmiderer, Corinna; Steinborn, Ralf; Novak, Johannes

    2012-03-01

    Garden sage (Salvia officinalis L., Lamiaceae) is one of the most important medicinal and aromatic plants and possesses antioxidant, antimicrobial, spasmolytic, astringent, antihidrotic and specific sensorial properties. The essential oil of the plant, formed mainly in very young leaves, is in part responsible for these activities. It is mainly composed of the monoterpenes 1,8-cineole, α- and β-thujone and camphor synthesized by the 1,8-cineole synthase, the (+)-sabinene synthase and the (+)-bornyl diphosphate synthase, respectively, and is produced and stored in epidermal glands. In this study, the seasonal influence on the formation of the main monoterpenes in young, still expanding leaves of field-grown sage plants was studied in two cultivars at the level of mRNA expression, analyzed by qRT-PCR, and at the level of end-products, analyzed by gas chromatography. All monoterpene synthases and monoterpenes were significantly influenced by cultivar and season. 1,8-Cineole synthase and its end product 1,8-cineole remained constant until August and then decreased slightly. The thujones increased steadily during the vegetative period. The transcript level of their corresponding terpene synthase, however, showed its maximum in the middle of the vegetative period and declined afterwards. Camphor remained constant until August and then declined, exactly correlated with the mRNA level of the corresponding terpene synthase. In summary, terpene synthase mRNA expression and respective end product levels were concordant in the case of 1,8-cineole (r=0.51 and 0.67 for the two cultivars, respectively; p<0.05) and camphor (r=0.75 and 0.82; p<0.05) indicating basically transcriptional control, but discordant for α-/β-thujone (r=-0.05 and 0.42; p=0.87 and 0.13, respectively). Copyright © 2011 Elsevier GmbH. All rights reserved.

  14. Improvement in the quality of hematopoietic prostaglandin D synthase crystals in a microgravity environment

    International Nuclear Information System (INIS)

    Tanaka, Hiroaki; Tsurumura, Toshiharu; Aritake, Kosuke; Furubayashi, Naoki; Takahashi, Sachiko; Yamanaka, Mari; Hirota, Erika; Sano, Satoshi; Sato, Masaru; Kobayashi, Tomoyuki; Tanaka, Tetsuo; Inaka, Koji; Urade, Yoshihiro

    2011-01-01

    Crystals of hematopoietic prostaglandin D synthase grown in microgravity show improved quality. Human hematopoietic prostaglandin synthase, one of the better therapeutic target enzymes for allergy and inflammation, was crystallized with 22 inhibitors and in three inhibitor-free conditions in microgravity. Most of the space-grown crystals showed better X-ray diffraction patterns than the terrestrially grown ones, indicating the advantage of a microgravity environment on protein crystallization, especially in the case of this protein

  15. Use of octaketide synthases to produce kermesic acid and flavokermesic acid

    DEFF Research Database (Denmark)

    2017-01-01

    A method for producing an octaketide derived aromatic compound of interest (e.g. carminic acid), wherein the method comprises (I): heterologous expression of a recombinantly introduced Type III polyketide synthase (PKS) gene encoding an octaketide synthase (OKS) to obtain non-reduced octaketide...... in vivo within the recombinant host cell and (II): converting in vivo the non-reduced octaketide of step (I) into a C14-C34 aromatic compound of interest (e.g. carminic acid)....

  16. Use of heterologous expressed polyketide synthase and small molecule foldases to make aromatic and cyclic compounds

    DEFF Research Database (Denmark)

    2016-01-01

    A method for producing individual or libraries of tri- to pentadecaketide-derived aromatic compounds of interest by heterologous expression of polyketide synthase and aromatase/cyclase in a recombinant host cell.......A method for producing individual or libraries of tri- to pentadecaketide-derived aromatic compounds of interest by heterologous expression of polyketide synthase and aromatase/cyclase in a recombinant host cell....

  17. Use of octaketide synthases to produce kermesic acid and flavokermesic acid

    DEFF Research Database (Denmark)

    2016-01-01

    A method for producing an octaketide derived aromatic compound of interest (e.g. carminic acid), wherein the method comprises (I): heterologous expression of a recombinantly introduced Type III polyketide synthase (PKS) gene encoding an octaketide synthase (OKS) to obtain non-reduced octaketide...... in vivo within the recombinant host cell and (II): converting in vivo the non-reduced octaketide of step (I) into a C14-C34 aromatic compound of interest (e.g. carminic acid)....

  18. The subcellular localization of yeast glycogen synthase is dependent upon glycogen content

    OpenAIRE

    Wilson, Wayne A.; Boyer, Michael P.; Davis, Keri D.; Burke, Michael; Roach, Peter J.

    2010-01-01

    The budding yeast, Saccharomyces cerevisiae, accumulates the storage polysaccharide glycogen in response to nutrient limitation. Glycogen synthase, the major form of which is encoded by the GSY2 gene, catalyzes the key regulated step in glycogen storage. Here, we utilize Gsy2p fusions to green fluorescent protein (GFP) to determine where glycogen synthase is located within cells. We demonstrate that the localization pattern of Gsy2-GFP depends upon the glycogen content of the cell. When glyco...

  19. The polyketide components of waxes and the Cer-cqu gene cluster encoding a novel polyketide synthase, the β-diketone synthase, DKS

    DEFF Research Database (Denmark)

    von Wettstein, Penny

    2017-01-01

    The primary function of the outermost, lipophilic layer of plant aerial surfaces, called the cuticle, is preventing non-stomatal water loss. Its exterior surface is often decorated with wax crystals, imparting a blue-grey color. Identification of the barley Cer-c, -q and -u genes forming the 101 kb...... Cer-cqu gene cluster encoding a novel polyketide synthase-the β-diketone synthase (DKS), a lipase/carboxyl transferase, and a P450 hydroxylase, respectively, establishes a new, major pathway for the synthesis of plant waxes. The major product is a β-diketone (14,16-hentriacontane) aliphatic that forms...

  20. Graphene Conductance Uniformity Mapping

    DEFF Research Database (Denmark)

    Buron, Jonas Christian Due; Petersen, Dirch Hjorth; Bøggild, Peter

    2012-01-01

    We demonstrate a combination of micro four-point probe (M4PP) and non-contact terahertz time-domain spectroscopy (THz-TDS) measurements for centimeter scale quantitative mapping of the sheet conductance of large area chemical vapor deposited graphene films. Dual configuration M4PP measurements......, demonstrated on graphene for the first time, provide valuable statistical insight into the influence of microscale defects on the conductance, while THz-TDS has potential as a fast, non-contact metrology method for mapping of the spatially averaged nanoscopic conductance on wafer-scale graphene with scan times......, dominating the microscale conductance of the investigated graphene film....