Sample records for suspended solids concentrations

  1. Ratios of total suspended solids to suspended sediment concentrations by particle size (United States)

    Selbig, W.R.; Bannerman, R.T.


    Wet-sieving sand-sized particles from a whole storm-water sample before splitting the sample into laboratory-prepared containers can reduce bias and improve the precision of suspended-sediment concentrations (SSC). Wet-sieving, however, may alter concentrations of total suspended solids (TSS) because the analytical method used to determine TSS may not have included the sediment retained on the sieves. Measuring TSS is still commonly used by environmental managers as a regulatory metric for solids in storm water. For this reason, a new method of correlating concentrations of TSS and SSC by particle size was used to develop a series of correction factors for SSC as a means to estimate TSS. In general, differences between TSS and SSC increased with greater particle size and higher sand content. Median correction factors to SSC ranged from 0.29 for particles larger than 500m to 0.85 for particles measuring from 32 to 63m. Great variability was observed in each fraction-a result of varying amounts of organic matter in the samples. Wide variability in organic content could reduce the transferability of the correction factors. ?? 2011 American Society of Civil Engineers.

  2. A study of metal ion adsorption at low suspended-solid concentrations (United States)

    Chang, Cecily C.Y.; Davis, J.A.; Kuwabara, J.S.


    A procedure for conducting adsorption studies at low suspended solid concentrations in natural waters (NaCl) concentration (0??1-0??002 m) and particle concentration (2-50 mg l-1). The lack of success of the Davis Leckie site bonding model in describing Zn(II) adsorption emphasizes the need for further studies of adsorption at low suspended-solid concentrations. ?? 1987.

  3. Impact of suspended solids concentration on sludge filterability in Full-scale membrane bioreactors

    NARCIS (Netherlands)

    Lousada Ferreira, M.D.C.; Van Lier, J.B.; Van der Graaf, J.H.J.M.


    The relation between activated sludge filterability and mixed liquor suspended solids (MLSS) concentration in membrane bioreactors (MBRs) is framed in a single hypothesis, explaining results seemingly contradictory. A total of 44 activated sludge samples were collected and analyzed on a variety of

  4. Influence of land use on total suspended solid and dissolved ion concentrations: Baton Rouge, Louisiana area

    Directory of Open Access Journals (Sweden)

    D. Carlson


    Full Text Available Past studies in the Baton Rouge, Louisiana area considered streamwater quality during storm events but ignored water quality during low flow periods. This study includes determination of streamwater quality during low flow time periods for none watersheds in East Baton Rouge Parish, Louisiana. These samples were collected during dry-low flow periods as indicated by water levels at USGS stream gauging sites for each stream. Chemical analysis for ions was completed using colorimeters and gravimetric analysis for total dissolved solids (TDS and total suspended solids (TSS. Land use appears to impact concentrations of ions, TDS and TSS in a variety of ways during periods of low flow. The two most rural watersheds, which are mainly underdeveloped, have higher concentrations of Fe and Mn. By contrast the three most urban watersheds, that are mainly commercial, industrial or residential, have higher concentrations of Si, SO4 and TDS.

  5. Calibration of a turbidity meter for making estimates of total suspended solids concentrations and beam attenuation coefficients in field experiments (United States)

    Usry, J. W.; Whitlock, C. H.


    Management of water resources such as a reservoir requires using analytical models which describe such parameters as the suspended sediment field. To select or develop an appropriate model requires making many measurements to describe the distribution of this parameter in the water column. One potential method for making those measurements expeditiously is to measure light transmission or turbidity and relate that parameter to total suspended solids concentrations. An instrument which may be used for this purpose was calibrated by generating curves of transmission measurements plotted against measured values of total suspended solids concentrations and beam attenuation coefficients. Results of these experiments indicate that field measurements made with this instrument using curves generated in this study should correlate with total suspended solids concentrations and beam attenuation coefficients in the water column within 20 percent.

  6. Suspended-sediment concentrations, yields, total suspended solids, turbidity, and particle-size fractions for selected rivers in Minnesota, 2007 through 2011 (United States)

    Ellison, Christopher A.; Savage, Brett E.; Johnson, Gregory D.


    Excessive sediment transport in rivers causes problems for flood control, soil conservation, irrigation, aquatic health, and navigation, as well as transporting harmful contaminants like organic chemicals and eutrophication-causing nutrients. In Minnesota, more than 5,800 miles of streams are identified as impaired by the Minnesota Pollution Control Agency (MPCA) due to elevated levels of suspended sediment. The U.S. Geological Survey, in cooperation with the MPCA, established a sediment monitoring network in 2007 and began systematic sampling of suspended-sediment concentration (SSC), total suspended solids (TSS), and turbidity in rivers across Minnesota to improve the understanding of fluvial sediment transport relations. Suspended-sediment samples were collected from 14 sites from 2007 through 2011. Analyses of these data indicated that the Zumbro River at Kellogg in southeast Minnesota had the highest mean SSC of 226 milligrams per liter (mg/L) followed by the Minnesota River at Mankato with a mean SSC of 193 mg/L. The single highest SSC of 1,250 mg/L was measured at the Zumbro River during the 2011 spring runoff. The lowest mean SSC of 21 mg/L was measured at Rice Creek in the northern Minneapolis-St. Paul metropolitan area. Total suspended solids (TSS) have been used as a measure of fluvial sediment by the MPCA since the early 1970s; however, TSS concentrations have been known to underrepresent the amount of suspended sediment. For this study, comparisons between concurrently sampled SSC and TSS indicated significant differences at every site, with SSC on average two times larger than TSS concentrations. Regression analysis indicated that 7 out of 14 sites had poor or no relation between SSC and streamflow. Only two sites, the Knife River and the Wild Rice River at Twin Valley, had strong correlations between SSC and streamflow, with coefficient of determination (R2) values of 0.82 and 0.80, respectively. In contrast, turbidity had moderate to strong

  7. Suspended-sediment concentrations, loads, total suspended solids, turbidity, and particle-size fractions for selected rivers in Minnesota, 2007 through 2011 (United States)

    Ellison, Christopher A.; Savage, Brett E.; Johnson, Gregory D.


    Sediment-laden rivers and streams pose substantial environmental and economic challenges. Excessive sediment transport in rivers causes problems for flood control, soil conservation, irrigation, aquatic health, and navigation, and transports harmful contaminants like organic chemicals and eutrophication-causing nutrients. In Minnesota, more than 5,800 miles of streams are identified as impaired by the Minnesota Pollution Control Agency (MPCA) due to elevated levels of suspended sediment. The U.S. Geological Survey, in cooperation with the MPCA, established a sediment monitoring network in 2007 and began systematic sampling of suspended-sediment concentrations (SSC), total suspended solids (TSS), and turbidity in rivers across Minnesota to improve the understanding of fluvial sediment transport relations. Suspended-sediment samples collected from 14 sites from 2007 through 2011 indicated that the Zumbro River at Kellogg in the driftless region of southeast Minnesota had the highest mean SSC of 226 milligrams per liter (mg/L) followed by the Minnesota River at Mankato with a mean SSC of 193 mg/L. During the 2011 spring runoff, the single highest SSC of 1,250 mg/L was measured at the Zumbro River. The lowest mean SSC of 21 mg/L was measured at Rice Creek in the northern Minneapolis- St. Paul metropolitan area. Total suspended solids (TSS) have been used as a measure of fluvial sediment by the MPCA since the early 1970s; however, TSS concentrations have been determined to underrepresent the amount of suspended sediment. Because of this, the MPCA was interested in quantifying the differences between SSC and TSS in different parts of the State. Comparisons between concurrently sampled SSC and TSS indicated significant differences at every site, with SSC on average two times larger than TSS concentrations. The largest percent difference between SSC and TSS was measured at the South Branch Buffalo River at Sabin, and the smallest difference was observed at the Des Moines

  8. A Landsat-based model for retrieving total suspended solids concentration of estuaries and coasts in China (United States)

    Wang, Chongyang; Chen, Shuisen; Li, Dan; Wang, Danni; Liu, Wei; Yang, Ji


    Retrieving total suspended solids (TSS) concentration accurately is essential for sustainable management of estuaries and coasts, which plays a key role in the interaction between hydrosphere, pedosphere and atmosphere. Although many TSS retrieval models have been published, the general inversion method that is applicable to different field conditions is still under research. In order to obtain a TSS remote sensing model that is suitable for estimating TSS concentrations with wide range in estuaries and coasts by Landsat imagery, after reviewing a number of Landsat-based TSS retrieval models and improving a comparatively better one among them, this study developed a quadratic model using the ratio of logarithmic transformation of red band and near-infrared band and logarithmic transformation of TSS concentration (QRLTSS) based on 119 in situ samples collected in 2006-2013 from five regions of China. It was found that the QRLTSS model works well and shows a satisfactory performance. The QRLTSS model based on Landsat TM (Thematic Mapper), ETM+ (Enhanced Thematic Mapper Plus) and OLI (Operational Land Imager) sensors explained about 72 % of the TSS concentration variation (TSS: 4.3-577.2 mg L-1, N = 84, P value proposed to solve the two-valued issue of the QRLTSS model and to retrieve TSS concentration from Landsat imagery. After a 6S model-based atmospheric correction of Landsat OLI and ETM+ imagery, the TSS concentrations of three regions (Moyangjiang River estuary, Pearl River estuary and Hanjiang River estuary) in Guangdong Province in China were mapped by the QRLTSS model. The results indicated that TSS concentrations in the three estuaries showed large variation ranging from 0.295 to 370.4 mg L-1. Meanwhile we found that TSS concentrations retrieved from Landsat imagery showed good validation accuracies with the synchronous water samples (TSS: 7-160 mg L-1, RMSE: 11.06 mg L-1, N = 22). The further validation from EO-1 Hyperion imagery also showed good

  9. Appropriate maximum holding times for analysis of total suspended solids concentration in water samples taken from open-channel waterways. (United States)

    Oudyn, Frederik W; Lyons, David J; Pringle, M J


    Many scientific laboratories follow, as standard practice, a relatively short maximum holding time (within 7 days) for the analysis of total suspended solids (TSS) in environmental water samples. In this study we have subsampled from bulk water samples stored at ∼4 °C in the dark, then analysed for TSS at time intervals up to 105 days after collection. The nonsignificant differences in TSS results observed over time demonstrates that storage at ∼4 °C in the dark is an effective method of preserving samples for TSS analysis, far past the 7-day standard practice. Extending the maximum holding time will ease the pressure on sample collectors and laboratory staff who until now have had to determine TSS within an impractically short period.

  10. The Applicability of the Distribution Coefficient, KD, Based on Non-Aggregated Particulate Samples from Lakes with Low Suspended Solids Concentrations.

    Directory of Open Access Journals (Sweden)

    Aine Marie Gormley-Gallagher

    Full Text Available Separate phases of metal partitioning behaviour in freshwater lakes that receive varying degrees of atmospheric contamination and have low concentrations of suspended solids were investigated to determine the applicability of the distribution coefficient, KD. Concentrations of Pb, Ni, Co, Cu, Cd, Cr, Hg and Mn were determined using a combination of filtration methods, bulk sample collection and digestion and Inductively Coupled Plasma-Mass Spectrometry (ICP-MS. Phytoplankton biomass, suspended solids concentrations and the organic content of the sediment were also analysed. By distinguishing between the phytoplankton and (inorganic lake sediment, transient variations in KD were observed. Suspended solids concentrations over the 6-month sampling campaign showed no correlation with the KD (n = 15 for each metal, p > 0.05 for Mn (r2 = 0.0063, Cu (r2 = 0.0002, Cr (r2 = 0.021, Ni (r2 = 0.0023, Cd (r2 = 0.00001, Co (r2 = 0.096, Hg (r2 = 0.116 or Pb (r2 = 0.164. The results implied that colloidal matter had less opportunity to increase the dissolved (filter passing fraction, which inhibited the spurious lowering of KD. The findings conform to the increasingly documented theory that the use of KD in modelling may mask true information on metal partitioning behaviour. The root mean square error of prediction between the directly measured total metal concentrations and those modelled based on the separate phase fractions were ± 3.40, 0.06, 0.02, 0.03, 0.44, 484.31, 80.97 and 0.1 μg/L for Pb, Cd, Mn, Cu, Hg, Ni, Cr and Co respectively. The magnitude of error suggests that the separate phase models for Mn and Cu can be used in distribution or partitioning models for these metals in lake water.

  11. The Applicability of the Distribution Coefficient, KD, Based on Non-Aggregated Particulate Samples from Lakes with Low Suspended Solids Concentrations. (United States)

    Gormley-Gallagher, Aine Marie; Douglas, Richard William; Rippey, Brian


    Separate phases of metal partitioning behaviour in freshwater lakes that receive varying degrees of atmospheric contamination and have low concentrations of suspended solids were investigated to determine the applicability of the distribution coefficient, KD. Concentrations of Pb, Ni, Co, Cu, Cd, Cr, Hg and Mn were determined using a combination of filtration methods, bulk sample collection and digestion and Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). Phytoplankton biomass, suspended solids concentrations and the organic content of the sediment were also analysed. By distinguishing between the phytoplankton and (inorganic) lake sediment, transient variations in KD were observed. Suspended solids concentrations over the 6-month sampling campaign showed no correlation with the KD (n = 15 for each metal, p > 0.05) for Mn (r2 = 0.0063), Cu (r2 = 0.0002, Cr (r2 = 0.021), Ni (r2 = 0.0023), Cd (r2 = 0.00001), Co (r2 = 0.096), Hg (r2 = 0.116) or Pb (r2 = 0.164). The results implied that colloidal matter had less opportunity to increase the dissolved (filter passing) fraction, which inhibited the spurious lowering of KD. The findings conform to the increasingly documented theory that the use of KD in modelling may mask true information on metal partitioning behaviour. The root mean square error of prediction between the directly measured total metal concentrations and those modelled based on the separate phase fractions were ± 3.40, 0.06, 0.02, 0.03, 0.44, 484.31, 80.97 and 0.1 μg/L for Pb, Cd, Mn, Cu, Hg, Ni, Cr and Co respectively. The magnitude of error suggests that the separate phase models for Mn and Cu can be used in distribution or partitioning models for these metals in lake water.

  12. Concentration, flux, and trend estimates with uncertainty for nutrients, chloride, and total suspended solids in tributaries of Lake Champlain, 1990–2014 (United States)

    Medalie, Laura


    The U.S. Geological Survey, in cooperation with the New England Interstate Water Pollution Control Commission and the Vermont Department of Environmental Conservation, estimated daily and 9-month concentrations and fluxes of total and dissolved phosphorus, total nitrogen, chloride, and total suspended solids from 1990 (or first available date) through 2014 for 18 tributaries of Lake Champlain. Estimates of concentration and flux, provided separately in Medalie (2016), were made by using the Weighted Regressions on Time, Discharge, and Season (WRTDS) regression model and update previously published WRTDS model results with recent data. Assessment of progress towards meeting phosphorus-reduction goals outlined in the Lake Champlain management plan relies on annual estimates of phosphorus flux. The percent change in annual concentration and flux is provided for two time periods. The R package EGRETci was used to estimate the uncertainty of the trend estimate. Differences in model specification and function between this study and previous studies that used WRTDS to estimate concentration and flux using data from Lake Champlain tributaries are described. Winter data were too sparse and nonrepresentative to use for estimates of concentration and flux but were sufficient for estimating the percentage of total annual flux over the period of record. Median winter-to-annual fractions ranged between 21 percent for total suspended solids and 27 percent for dissolved phosphorus. The winter contribution was largest for all constituents from the Mettawee River and smallest from the Ausable River. For the full record (1991 through 2014 for total and dissolved phosphorus and chloride and 1993 through 2014 for nitrogen and total suspended solids), 6 tributaries had decreasing trends in concentrations of total phosphorus, and 12 had increasing trends; concentrations of dissolved phosphorus decreased in 6 and increased in 8 tributaries; fluxes of total phosphorus decreased in 5 and

  13. Sedimentation of suspended solids in ultrasound field

    Directory of Open Access Journals (Sweden)

    Vikulina Vera


    Full Text Available Physical and chemical effects of aquatic environment that occur in an ultrasonic field change the sedimentation rate of coagulated suspension. This might only happen in case of cavitation of ultrasonic filed that causes a change of potentials of the medium. Research of the influence of ultrasonic vibrations on coagulation of suspended solids within water purification allows expanding their scope of implementation. The objective of the research is to estimate the effect of ultrasound on the sedimentation of the suspended solids, to determine of the efficiency of the process in relation to the dose of the coagulant, and to calculate the numerical values of the constants in the theoretical equation. The experiment condition was held in the water with the clay substances before the introduction of the coagulant. The method of magnetostriction ultrasonic generator was applied to receive ultrasonic vibration. Estimate of concentration of clay particles in water was performed using photometry. As a result of the research, the obtained data allow determining the increase in efficiency of suspended particles sedimentation related to the dose of coagulant, depending on time of ultrasonic treatment. The experiments confirmed the connection between the effect of sedimentation in the coagulation process, the coagulant dose and the time of scoring. Studies have shown that the increase in the duration of ultrasonic treatment causes a decrease of administered doses of coagulant.

  14. Organics and Suspended Solids Removal from Hospital

    Directory of Open Access Journals (Sweden)

    Fakhri Y. Hmood


    Full Text Available The Sequencing Batch Reactor (SBR method is used for treating samples of waste water taken from hospitals in Mosul. Many run periods are used (6-24 hours for             6 months. It is found that the organics and suspended solids removal increase with increasing the period of run, it is in the range ( 96-82 % and ( 100-95 % respectively, while the pH values are nearly neutral (7.05 to 7.5.     BOD5 and SS concentrations of the effluent are within the limits of Iraqi standards,  40:30 mg/l respectively. Hence, SBR method could be used for treating hospitals, small factories and some  residential sectors waste waters.  

  15. Accuracy of different sensors for the estimation of pollutant concentrations (total suspended solids, total and dissolved chemical oxygen demand) in wastewater and stormwater. (United States)

    Lepot, Mathieu; Aubin, Jean-Baptiste; Bertrand-Krajewski, Jean-Luc


    Many field investigations have used continuous sensors (turbidimeters and/or ultraviolet (UV)-visible spectrophotometers) to estimate with a short time step pollutant concentrations in sewer systems. Few, if any, publications compare the performance of various sensors for the same set of samples. Different surrogate sensors (turbidity sensors, UV-visible spectrophotometer, pH meter, conductivity meter and microwave sensor) were tested to link concentrations of total suspended solids (TSS), total and dissolved chemical oxygen demand (COD), and sensors' outputs. In the combined sewer at the inlet of a wastewater treatment plant, 94 samples were collected during dry weather, 44 samples were collected during wet weather, and 165 samples were collected under both dry and wet weather conditions. From these samples, triplicate standard laboratory analyses were performed and corresponding sensors outputs were recorded. Two outlier detection methods were developed, based, respectively, on the Mahalanobis and Euclidean distances. Several hundred regression models were tested, and the best ones (according to the root mean square error criterion) are presented in order of decreasing performance. No sensor appears as the best one for all three investigated pollutants.

  16. The spatial and temporal variation of total suspended solid concentration in Pearl River Estuary during 1987-2015 based on remote sensing. (United States)

    Wang, Chongyang; Li, Weijiao; Chen, Shuisen; Li, Dan; Wang, Danni; Liu, Jia


    The movement and migration of total suspended solid (TSS) are the essential component of global material cycling and change. Based on the TSS concentrations retrieved from 112 scenes of Landsat remote sensing imageries during 1987-2015, the spatial and temporal variations of TSS concentration in high flow season and low flow seasons of six sub-regions (west shoal, west channel, middle shoal, east channel, east shoal and Pearl River Estuary Chinese White Dolphin National Nature Reserve and its adjacent waters (NNR)) of Pearl River Estuary (PRE) were analyzed and compared by statistical simulation. It was found that TSS concentrations in east and west shoals were about 23mg/L and 64mg/L higher than that of the middle shoal, respectively. There was a significant decreasing trend of TSS concentration from the northwest (223.7mg/L) to southeast (51.4mg/L) of study area, with an average reduction of 5.86mg/Lperkm, which mainly attributes to unique interaction of runoff and tide in PRE. In high flow season, there existed a significant and definite annual cycle period (5-8years) of TSS concentration change primarily responding to the periodic variation of precipitation. There were five full-fledged period changes of TSS detected in west shoal and west channel (the years of changes in 1988, 1994, 1998, 2003, 2010, 2015), while there were the last four cycle periods found in middle shoal, east channel, east shoal and NNR only. TSS concentrations in shoals and channels of PRE showed a significant decreased trend mainly due to the dam construction at the same time, with an average annual TSS concentration decrease of 5.7-10.1mg/L in high flow season from 1988 to 2015. There was no significant change trend of TSS concentration in NNR before 2003, but the TSS concentration decreased significantly after the establishment of the NNR since June 2003, with an average annual decrease of 9.7mg/L from 2004 to 2015. It was deduced that man-made protection measures had a great influence

  17. Suspended sediment concentration and particle size distribution ...

    Indian Academy of Sciences (India)

    face area, shape, minerals and source) and conse- quent interaction with heavy metal concentrations. (HMCs). Recent studies have shown a growing awareness of the wider environmental significance of the suspended sediment loads transported by rivers and streams. This includes the importance of fine grain sediment in ...

  18. Twelve Years of Monitoring Phosphorus and Suspended-Solids Concentrations and Yields in the North Fork Ninnescah River above Cheney Reservoir, South-Central Kansas 1997-2008 (United States)

    Stone, Mandy L.; Graham, Jennifer L.; Ziegler, Andrew C.


    Cheney Reservoir, located on the North Fork Ninnescah River in south-central Kansas, is the primary water supply for the city of Wichita and an important recreational resource. Concerns about taste-and-odor occurrences in Cheney Reservoir have drawn attention to potential pollutants, including total phosphorus (TP) and total suspended solids (TSS). July 2009 was the 15th anniversary of the establishment of the Cheney Reservoir Watershed pollution management plan. The U.S. Geological Survey (USGS), in cooperation with the city of Wichita, has collected water-quality data in the basin since 1996, and has monitored water quality continuously on the North Fork Ninnescah River since 1998. This fact sheet describes 12 years (1997-2008) of computed TP and TSS data and compares these data with water-quality goals for the North Fork Ninnescah River, the main tributary to Cheney Reservoir.

  19. Experimental study of the viscosity of suspensions: effect of solid fraction, particle size and suspending liquid

    NARCIS (Netherlands)

    Konijn, B.J.; Sanderink, O.B.J.; Kruyt, Nicolaas P.


    The behaviour of nearly neutrally-buoyant suspensions has been studied experimentally, using a concentric-cylinder rheometer. The effect on the suspension viscosity of: (i) solid fraction, (ii) diameter of the solid, spherical particles, (iii) viscosity of the suspending liquid, and (iv) shear rate

  20. Measurements of solids concentration and axial solids velocity in gas-solid two-phase flows.

    NARCIS (Netherlands)

    Nieuwland, J.J.; Nieuwland, J.J.; Meijer, R.; Kuipers, J.A.M.; van Swaaij, Willibrordus Petrus Maria


    Several techniques reported in the literature for measuring solids concentration and solids velocity in (dense) gas-solid two-phase flow have been briefly reviewed. An optical measuring system, based on detection of light reflected by the suspended particles, has been developed to measure local

  1. Suspended sediment concentration profiles from synoptic satellite observations

    Digital Repository Service at National Institute of Oceanography (India)

    Ramakrishnan, R.; Rajawat, A; Chauhan, O.S.

    A method is developed to estimate vertical suspended sediment concentration (SSC) profiles in Gulf of Kachchh, from the sediment concentration values derived from synoptic observations of Ocean Colour Monitor (OCM). Under the influence of currents...

  2. Geochemistry of suspended and settling solids in two freshwater lakes.

    NARCIS (Netherlands)

    Koelmans, A.A.


    This study describes the 1987–1992 time variationof the bulk chemical composition, levels of heavymetals, arsenic, nitrogen and phosporous insuspended and settling solids in Lake Volkerak andLake Zoom (The Netherlands). Suspended and setlingsolids were collected with continuous flowcentrifuges and

  3. Comparison of Suspended Solid Separation in Advanced Storm Overflow Structures

    DEFF Research Database (Denmark)

    Larsen, Torben; Sørensen, Morten Steen


    This paper describes a laboratory investigation of the separation of suspended solids in a circular weir overflow and a vortex separator. The basic idea is to evaluate the efficiency of a vortical flow in the overflow chamber, and to compare these results with other overflow structures....

  4. Current-use insecticides, phosphates and suspended solids in the ...

    African Journals Online (AJOL)

    In Western Cape orchard areas, the last pesticide application of the growing season in summer takes place at the end of February. Pesticides, total phosphates and total suspended solids (TSS) were measured in the Lourens River at the beginning of April 1999 prior to the first rainfall of the rainy season and in the middle of ...

  5. Delineating Effects of Ionic Strength and Suspended Solids on Ammonia Volatilization from Dairy Manure Slurry (United States)

    Koirala, K.


    Ammonia emission is a major concern due to its adverse effects on animal and human health. Ionic strength and suspended solids play key roles in the ammonia volatilization process. These two parameters, however, are usually lumped together in form of total solids. The objective of this study was to separate the contribution of suspended solids (SS) from that of ionic strength (IS) on ammonia volatilization in liquid dairy manure. A two-way factorial experiment was conducted to simultaneously test the effects of IS and SS on ammonium dissociation: a key element of the ammonia volatilization process. The fraction of ammonia (β) in total ammoniacal nitrogen (TAN) was experimentally determined in a convective emission chamber, for each level of SS and IS, at a constant wind speed of 1.5 m s-1, and air and liquid temperature of 25°C. The two way analysis of variance showed a significant effect of SS concentration (p = 0.04) on fraction of ammonia in the liquid dairy manure, while the effect of ionic strength was marginal (p = 0.05). The highest dissociation of ammonium was observed in manure with the lowest SS concentration (0%) and the lowest ionic strength (0.10 mol L-1). Significant increases in suspended solids concentration and ionic strength were necessary to influence the ammonium dissociation in dairy manure. Results revealed that substantially high content of suspended solids (> 3.0%) or relatively high dilution of manure with water (30%) were necessary for these two parameters to play significant roles in the ammonia volatilization mechanism in liquid dairy manure. Results also showed that the β was more sensitive to the changes in suspended solids concentration than in the changes in ionic strength within the ranges of SS and IS examined in this study. Overall, the SS and IS effects on ammonium dissociation (and by extension on ammonia volatilization process) were thus found negligible within the normal ranges of liquid dairy manure characteristics.


    Directory of Open Access Journals (Sweden)

    N. Laili


    Full Text Available The Landsat-8 satellite imagery is now highly developed compares to the former of Landsat projects. Both land and water area are possibly mapped using this satellite sensor. Considerable approaches have been made to obtain a more accurate method for extracting the information of water area from the images. It is difficult to generate an accurate water quality information from Landsat images by using some existing algorithm provided by researchers. Even though, those algorithms have been validated in some water area, but the dynamic changes and the specific characteristics of each area make it necessary to get them evaluated and validated over another water area. This paper aims to make a new algorithm by correlating the measured and estimated TSS and Chla concentration. We collected in-situ remote sensing reflectance, TSS and Chl-a concentration in 9 stations surrounding the Poteran islands as well as Landsat 8 data on the same acquisition time of April 22, 2015. The regression model for estimating TSS produced high accuracy with determination coefficient (R2, NMAE and RMSE of 0.709; 9.67 % and 1.705 g/m3 respectively. Whereas, Chla retrieval algorithm produced R2 of 0.579; NMAE of 10.40% and RMSE of 51.946 mg/m3. By implementing these algorithms to Landsat 8 image, the estimated water quality parameters over Poteran island water ranged from 9.480 to 15.801 g/m3 and 238.546 to 346.627 mg/m3 for TSS and Chl-a respectively.


    Directory of Open Access Journals (Sweden)

    Aries Dwi Siswanto


    horizontal and vertical. Accumulation of suspended sediment (TSS horizontally greatly influenced by surface currents and waves generated by the wind. TSS discovery is supposed to influence the spreading on a vertical profile. The second condition of distribution of suspended sediment (TSS effect on optimizing the penetration of sunlight in the water. Suspended sediments (TSS became one of the important physical factor as an indicator of water conditions. This study aims to determine the distribution of Total Suspended Solid (TSS in the waters of Bangkalan. The main material used in this study is an example of water and environmental parameter data (tidal and brightness taken at 7 stations in August-September 2013 in the Madura Strait, Bangkalan. Gravimetric method (ISO-06-6989.3-2004 is used for the analysis of Total Suspended Solid (TSS. Environmental parameters data were analyzed descriptively. TSS analysis shows different value on some of the research station for TSS. Concentration per week low of 35 mg / L (Station 3, surface profile, the first week and the highest was 620 mg / L (Station 4, the basic profile, the first week. In general, concentrations of vertical TSS (from surface-basic tends to be greater, might be influenced by the type of substrate and flow parameters are likely to cause agitation in the basic profile. Environmental conditions (brightness and current shows that areas with high concentrations of TSS tend to have the value of a low brightness with the larger speed of currents.Keywords: brightness, current patterns, Total Suspended Solid (TSS

  8. Modeled summer background concentration nutrients and suspended sediment in the mid-continent (USA) great rivers (United States)

    We used regression models to predict background concentration of four water quality indictors: total nitrogen (N), total phosphorus (P), chloride, and total suspended solids (TSS), in the mid-continent (USA) great rivers, the Upper Mississippi, the Lower Missouri, and the Ohio. F...

  9. Nature of suspended particulate matter and concentrations of heavy ...

    African Journals Online (AJOL)

    The concentrations of metals in bottom sediment in the Tanzanian waters of Lake Victoria and the nature of suspended particulate matter (SPM) were analysed. The objective of the study was to compare levels of metals in sediment from different locations and to establish their sources. Metal concentrations were higher in ...

  10. Estimation of suspended sediment concentration by acoustic ...

    African Journals Online (AJOL)

    However, the acoustic properties of natural sediments vary and depend on many parameters such as particle size, shape, mineralogy and distribution of those parameters in sample. Therefore, this study was conducted to determine the possibility of soil sediment concentration with the f and equations, which were obtained ...

  11. Simulation of suspended sediment transport initialized with satellite derived suspended sediment concentrations (United States)

    Ramakrishnan, Ratheesh; Rajawat, A. S.


    Suspended sediment transport in the Gulf of Kachchh is simulated utilizing the suspended sediment concentration (SSC) derived from Oceansat OCM imagery, as the initial condition in MIKE-21 Mud Transport model. Optimization of the model mud parameters, like settling velocity and critical shear stress for erosion are realized with respect to the sediment size distribution and the bottom bed materials observed in the Gulf. Simulated SSCs are compared with alternate OCM derived SSC. The results are observed to be impetus where the model is able to generate the spatial dynamics of the sediment concentrations. Sediment dynamics like deposition, erosion and dispersion are explained with the simulated tidal currents and OCM derived sediment concentrations. Tidal range is observed as the important physical factor controlling the deposition and resuspension of sediments within the Gulf. From the simulation studies; maximum residual current velocities, tidal fronts and high turbulent zones are found to characterise the islands and shoals within the Gulf, which results in high sediment concentrations in those regions. Remarkable variability in the bathymetry of the Gulf, different bed materials and varying tidal conditions induces several circulation patterns and turbulence creating the unique suspended sediment concentration pattern in the Gulf.

  12. Dynamic modeling of total suspended solids in the wetland Jaboque, Bogotá (Colombia

    Directory of Open Access Journals (Sweden)

    Julio Eduardo Beltrán-Vargas


    Full Text Available We propose a dynamic simulation model to provide a general explanation for the behavior of total suspended solids in the Jaboque wetland (Bogotá DC. The analyses were performed in three areas with distinct physical and chemical characteristics. The model predicted concentrations of total suspended solids in the months of April, May, June, October and November. Values ranged from 85 mg L-1 and 101 mg L-1 with an average of 65.12 mg L-1 with a hydraulic time retention between eight and nine days per year for the first area, the second area between 57 and 69 with an average of 50 mg L-1 with a hydraulic time between 20 and 23 days per year and in the third area between 56 mg L-1 and 67 mg L-1 with a mean of 48.8 mg L-1 and a hydraulic retention time between 24 and 26 days per year. The months of December, January, February, August and September showed a tendency to have lower values. The estimated values of total suspended solids based on our model had an acceptable correspondence, R2 = 0.95, 0.71, 0.67, with the actual values in all cases. The relative error for each area was 0.10, 0.20 and 0.26, demonstrating that the model does not overestimate the results.

  13. 40 CFR 227.32 - Liquid, suspended particulate, and solid phases of a material. (United States)


    ... MATERIALS Definitions § 227.32 Liquid, suspended particulate, and solid phases of a material. (a) For the... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Liquid, suspended particulate, and solid phases of a material. 227.32 Section 227.32 Protection of Environment ENVIRONMENTAL PROTECTION...

  14. High suspended solids as a factor in reproductive failure of a freshwater mussel (United States)

    Andrew M. Gascho-Landis; Wendell R. Haag; James A. Stoeckel


    Elevated suspended solids are a widespread stressor of aquatic ecosystems, but their effects on growth and reproduction in freshwater mussels are largely unknown. We fertilized experimental ponds to create a gradient in total suspended solids (TSS) and examined the effects of TSS on growth, nutritional status, reproduction, and clearance rate in Ligumia subrostrata....

  15. Effects of temperature, total dissolved solids, and total suspended solids on survival and development rate of larval Arkansas River Shiner (United States)

    Mueller, Julia S.; Grabowski, Timothy B.; Brewer, Shannon K.; Worthington, Thomas A.


    Decreases in the abundance and diversity of stream fishes in the North American Great Plains have been attributed to habitat fragmentation, altered hydrological and temperature regimes, and elevated levels of total dissolved solids and total suspended solids. Pelagic-broadcast spawning cyprinids, such as the Arkansas River Shiner Notropis girardi, may be particularly vulnerable to these changing conditions because of their reproductive strategy. Our objectives were to assess the effects of temperature, total dissolved solids, and total suspended solids on the developmental and survival rates of Arkansas River Shiner larvae. Results suggest temperature had the greatest influence on the developmental rate of Arkansas River Shiner larvae. However, embryos exposed to the higher levels of total dissolved solids and total suspended solids reached developmental stages earlier than counterparts at equivalent temperatures. Although this rapid development may be beneficial in fragmented waters, our data suggest it may be associated with lower survival rates. Furthermore, those embryos incubating at high temperatures, or in high levels of total dissolved solids and total suspended solids resulted in less viable embryos and larvae than those incubating in all other temperature, total dissolved solid, and total suspended solid treatment groups. As the Great Plains ecoregion continues to change, these results may assist in understanding reasons for past extirpations and future extirpation threats as well as predict stream reaches capable of sustaining Arkansas River Shiners and other species with similar early life-history strategies.

  16. Pesticide survey in water and suspended solids from the Uruguay River Basin, Argentina. (United States)

    Williman, Celia; Munitz, Martín S; Montti, María I T; Medina, María B; Navarro, Agustín F; Ronco, Alicia E


    The Uruguay River is receptor of pollutants, such as pesticides, from agriculture activities along its course. The present study reports concentration levels of organochlorinate, organophosphorus, and other pesticides in water and suspended solids in nine sampling sites of the Uruguay River. Data analyses included principal component analysis (PCA) to assess differences between sampling sites contamination. Most of the tested pesticides were ubiquitous due to the widely use in the chemical control of pests implemented in the region. Detected concentrations of aldrin, chlordane, dieldrin, endrin, heptachlor epoxide, lindane, 4,4'-DDT, endosulfan, chlorpyrifos, diazinon, methyl-parathion, and malathion were found to be over regional and international concentration level guidelines, according to the European Union, the US Environmental Protection Agency, or the Argentinean Secretariat of Environment and Sustainable Development. For this reason, future studies in Uruguay River Basin are needed.

  17. Suspended-sediment and suspended-sand concentrations and loads for selected streams in the Mississippi River Basin, 1940-2009 (United States)

    Heimann, David C.; Cline, Teri L.; Glaspie, Lori M.


    This report presents suspended-sediment concentration and streamflow data, describes load-estimation techniques used in the computation of annual suspended-sediment loads, and presents annual suspended-sediment loads for 48 streamgaging stations within the Mississippi River Basin. Available published, unpublished, and computed annual total suspended-sediment and suspended-sand loads are presented for water years 1940 through 2009. When previously published annual loads were not available, total suspended-sediment and sand loads were computed using available data for water years 1949 through 2009. A table of suspended-sediment concentration and daily mean streamflow data used in the computation of annual loads is presented along with a table of compiled and computed annual suspended-sediment and suspended-sand loads, annual streamflows, and flow-weighted concentrations for the 48 stations.

  18. The clam (Chamelea gallina: evaluation of the effects of solids suspended in seawater on bivalve molluscs

    Directory of Open Access Journals (Sweden)

    Salvatora Angela Angioni


    Full Text Available The study was designed to evaluate the effects of solids in suspension in seawater on clams (Chamelea gallina. The aim was to investigate the possible correlation between the widespread deaths of clams in the coastal waters of the central and northern Adriatic in the last five years and increased concentrations of solids in suspension. The research involved conducting 96-hour tests on clams farmed in aquariums containing filtered seawater. The tests were preceded by a 7-day adaptation stage to allow the molluscs to acclimatise. During this period, the clams were fed on unicellular seaweed (Dunaliella tertiolecta. The molluscs were exposed to particles of solids in suspension consisting of pools of silica gel (SiO2 granules of various sizes, similar to those constituting silt, whose presence and suspension in the sea considerably increase after heavy rain and heavy seas. The study established that the number of deaths caused by solids suspended in seawater at the concentrations used in the tests was not statistically significant.

  19. Remote Sensing Studies of Suspended Sediment Concentration Variation in Barito Delta (United States)

    Arisanty, Deasy; Nur Saputra, Aswin


    The dynamic of suspended sediment concentration in Barito Delta depend on the process in upstream. Agriculture, mining, and illegal logging in Barito River upstream has an effect for suspended sediment concentration in Barito Delta. The objective of research is to estimate the variation of suspended sediment concentration in Barito Delta. The data of research consist of Landsat 7 in year 2011 and measurement result data of suspended sediment concentration both in wet season and dry season in year 2011. Data analysis is regression analysis to estimates the variation of suspended sediment concentration in Barito Delta. The method of research compares three types of spectral transformation for suspended sediment that is Normalized Suspended Material Index (NSMI), Normalized Differences Suspended Sediment Index (NDSSI), and band ratio (green/blue). The result of the transformation is compared with the value of the field measurement. Based on the result of the comparison can be known the suitable type of transformation for the suspended sediment estimation in Barito Delta. The result of research explains that NSMI has the highest value to estimate the variation of suspended sediment concentration in Barito Delta.

  20. Assessment of conservation easements, total phosphorus, and total suspended solids in West Fork Beaver Creek, Minnesota, 1999-2012 (United States)

    Christensen, Victoria G.; Kieta, Kristen A.


    This study examined conservation easements and their effectiveness at reducing phosphorus and solids transport to streams. The U.S. Geological Survey cooperated with the Minnesota Board of Water and Soil Resources and worked collaboratively with the Hawk Creek Watershed Project to examine the West Fork Beaver Creek Basin in Renville County, which has the largest number of Reinvest In Minnesota land retirement contracts in the State (as of 2013). Among all conservation easement programs, a total of 24,218 acres of agricultural land were retired throughout Renville County, and 2,718 acres were retired in the West Fork Beaver Creek Basin from 1987 through 2012. Total land retirement increased steadily from 1987 until 2000. In 2000, land retirement increased sharply because of the Minnesota River Conservation Reserve Enhancement Program, then leveled off when the program ended in 2002. Streamflow data were collected during 1999 through 2011, and total phosphorus and total suspended solids data were collected during 1999 through 2012. During this period, the highest peak streamflow of 1,320 cubic feet per second was in March 2010. Total phosphorus and total suspended solids are constituents that tend to increase with increases in streamflow. Annual flow-weighted mean total-phosphorus concentrations ranged from 0.140 to 0.759 milligrams per liter, and annual flow-weighted mean total suspended solids concentrations ranged from 21.3 to 217 milligrams per liter. Annual flow-weighted mean total phosphorus and total suspended solids concentrations decreased steadily during the first 4 years of water-quality sample collection. A downward trend in flow-weighted mean total-phosphorus concentrations was significant from 1999 through 2008; however, flow-weighted total-phosphorus concentrations increased substantially in 2009, and the total phosphorus trend was no longer significant. The high annual flow-weighted mean concentrations for total phosphorus and total suspended solids

  1. Treatment of wastewater containing a large amount of suspended solids by a novel multi-staged UASB reactor. (United States)

    Uemura, S; Harada, H; Ohashi, A; Torimura, S


    Treatment of artificial wastewater containing a large amount of suspended solids comprised of soybean processing waste and pig fodder was studied using a novel multi-staged upflow anaerobic sludge blanket reactor. The reactor consisted of three compartments, each containing a gas solid separator. The wastewater had chemical oxygen demand of approximately 21600 mg l(-1), suspended solids of 12800 mg l(-1), and an ammonia concentration of 945 mg l(-1). A continuous experiment without effluent circulation showed that the multi-staged reactor was not that effective for the treatment of wastewater containing a large amount of suspended solids. However, operation of the reactor with circulation of effluent enabled the reactor to achieve organic removal of 85% and approximately 70% methane conversion at loading rates of between 4.0 to 5.4 kg-chemical oxygen demand per cubic meter per day, meaning that the reactor was more effective when effluent was circulated. Morphological investigation revealed that the crude fiber in the sludge was partially degraded and that it had many small depressions on its surface. Evolved biogas may have become caught in these depressions of the fibers and caused washout of the sludge.

  2. High concentration suspended sediment measurments using acontinuous fiber optic in-stream transmissometer

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, Chris G.; Laycak, Danny T.; Hoppes, William; Tran,Nguyen T.; Shi, Frank G.


    Suspended sediment loads mobilized during high flow periods in rivers and streams are largely uncharacterized. In smaller and intermittent streams, a large storm may transport a majority of the annual sediment budget. Therefore monitoring techniques that can measure high suspended sediment concentrations at semi-continuous time intervals are needed. A Fiber optic In-stream Transmissometer (FIT) is presented for continuous measurement of high concentration suspended sediment in storm runoff. FIT performance and precision were demonstrated to be reasonably good for suspended sediment concentrations up to 10g/L. The FIT was compared to two commercially available turbidity devices and provided better precision and accuracy at both high and low concentrations. Both turbidity devices were unable to collect measurements at concentrations greater than 4 g/L. The FIT and turbidity measurements were sensitive to sediment particle size. Particle size dependence of transmittance and turbidity measurement poses the greatest problem for calibration to suspended sediment concentration. While the FIT was demonstrated to provide acceptable measurements of high suspended sediment concentrations, approaches to real-time suspended sediment detection need to address the particle size dependence in concentration measurements.

  3. Satellite estimates of wide-range suspended sediment concentrations in Changjiang (Yangtze) estuary using MERIS data

    NARCIS (Netherlands)

    Shen, F.; Verhoef, W.; Zhou, Y.; Salama, M.S.; Liu, X.


    The Changjiang (Yangtze) estuarine and coastal waters are characterized by suspended sediments over a wide range of concentrations from 20 to 2,500 mg l-1. Suspended sediment plays important roles in the estuarine and coastal system and environment. Previous algorithms for satellite estimates of

  4. Particle size distribution of suspended solids in the Chesapeake Bay entrance and adjacent shelf waters (United States)

    Byrnes, M. R.; Oertel, G. F.


    Characteristics of suspended solids, including total suspended matter, total suspended inorganics, total suspended organics, particle size distribution, and the presence of the ten most prominent particle types were determined. Four research vessels simultaneously collected samples along four transects. Samples were collected within a 2-hour period that coincided with the maximum ebb penetration of Chesapeake Bay outwelling. The distribution of primary and secondary particle size modes indicate the presence of a surface or near-surface plume, possibly associated with three sources: (1) runoff, (2) resuspension of material within the Bay, and/or (3) resuspension of material in the area of shoals at the Bay mouth. Additional supportive evidence for this conclusion is illustrated with ocean color scanner data.

  5. Surface clogging process modeling of suspended solids during urban stormwater aquifer recharge. (United States)

    Wang, Zijia; Du, Xinqiang; Yang, Yuesuo; Ye, Xueyan


    Aquifer recharge, which uses urban stormwater, is an effective technique to control the negative effects of groundwater over-exploitation, while clogging problems in infiltration systems remain the key restricting factor in broadening its practice. Quantitative understanding of the clogging process is still very poor. A laboratory study was conducted to understand surface physical clogging processes, with the primary aim of developing a model for predicting suspended solid clogging processes before aquifer recharge projects start. The experiments investigated the clogging characteristics of different suspended solid sizes in recharge water by using a series of one-dimensional fine quartz sand columns. The results showed that the smaller the suspended particles in recharge water, the farther the distance of movement and the larger the scope of clogging in porous media. Clogging extents in fine sand were 1 cm, for suspended particle size ranging from 0.075 to 0.0385 mm, and 2 cm, for particles less than 0.0385 mm. In addition, clogging development occurred more rapidly for smaller suspended solid particles. It took 48, 42, and 36 hr respectively, for large-, medium-, and small-sized particles to reach pre-determined clogging standards. An empirical formula and iteration model for the surface clogging evolution process were derived. The verification results obtained from stormwater recharge into fine sand demonstrated that the model could reflect the real laws of the surface clogging process.

  6. Occurrence and persistence of fungicides in bed sediments and suspended solids from three targeted use areas in the United States (United States)

    Smalling, Kelly L.; Reilly, Timothy J.; Sandstrom, Mark W.; Kuivila, Kathryn


    To document the environmental occurrence and persistence of fungicides, a robust and sensitive analytical method was used to measure 34 fungicides and an additional 57 current-use pesticides in bed sediments and suspended solids collected from areas of intense fungicide use within three geographic areas across the United States. Sampling sites were selected near or within agricultural research farms using prophylactic fungicides at rates and types typical of their geographic location. At least two fungicides were detected in 55% of the bed and 83% of the suspended solid samples and were detected in conjunction with herbicides and insecticides. Six fungicides were detected in all samples including pyraclostrobin (75%), boscalid (53%), chlorothalonil (41%) and zoxamide (22%). Pyraclostrobin, a strobilurin fungicide, used frequently in the United States on a variety of crops, was detected more frequently than p,p′-DDE, the primary degradate of p,p′-DDT, which is typically one of the most frequently occurring pesticides in sediments collected within highly agricultural areas. Maximum fungicide concentrations in bed sediments and suspended solids were 198 and 56.7 μg/kg dry weight, respectively. There is limited information on the occurrence, fate, and persistence of many fungicides in sediment and the environmental impacts are largely unknown. The results of this study indicate the importance of documenting the persistence of fungicides in the environment and the need for a better understanding of off-site transport mechanisms, particularly in areas where crops are grown that require frequent treatments to prevent fungal diseases.

  7. Basic hydraulic experiment on the saturated concentration of suspended load due to tsunamis (United States)

    Takahashi, Tomoyuki; Somekawa, Shiho


    When tsunamis arrive in the shallow sea, a huge amount of suspended load is generated by large velocity and strong turbulence. The suspended load causes the geomorphic processes of erosion and deposition. Because the suspended load cannot be increased endlessly, it should have the saturated concentration. Many numerical models of sediment transport due to tsunamis have assumed a constant value of 1% for the saturated concentration empirically. However, it is supposed as a function of velocity. In this study, a hydraulic experiment was carried out to investigate a relationship between velocity and the saturated concentration of suspended load when tsunamis attack. A water circulation pipe used in the experiment was 10 cm in a diameter, 260 cm in length and 50 cm in width. A velocity of water flow in the pipe had been controlled by two pumps and two valves. It was changed from 0.24 to 1.22 m/s. Various amounts of sand was spread on the bottom of pipe. The amount of sand was changed from 0.1 to 10% as converted in the concentration of suspended load if all sand suspended. A diameter and a density of the sand were 0.267 mm and 2.64 x 103 kg/m^3. A condition of sediment transport in the pipe was recorded by video camera from a transparent window at the side of pipe. The condition was judged as all sand particles were suspended or not. The former condition indicates that the concentration of suspended load is saturated and the latter does it is not saturated. When velocity was smaller than 0.47 m/s, there was no suspended load because of a weak tractive force. When velocity became larger, the suspended load was generated and the concentration also became higher. However, the concentration had the upper limit and surplus sand appeared on the bed of pipe when velocity became much larger. The condition gave the saturated concentration of suspended load. When velocity was 0.665 m/s, the saturated concentration was smaller than 1% which is used in many numerical simulations

  8. Solid and suspended/dissolved waste (N, P, O) from rainbow trout (Oncorynchus mykiss)

    DEFF Research Database (Denmark)

    Dalsgaard, Anne Johanne Tang; Pedersen, Per Bovbjerg


    Quantifying aquaculture waste into different waste fractions will make it possible to design different treatment setups for obtaining specific cleaning objectives. The aim of this study was therefore to measure “all” solid and suspended/dissolved (i.e. unsedimented) waste from juvenile rainbow...... trout (Oncorynchus mykiss) fed three commonly applied commercial diets, “all” waste referring to: total nitrogen (N), total ammonia nitrogen (TAN=NH3-N+NH4-N), total phosphorus (P), and organicmatter characterized by the chemical oxygen demand (COD) and the biological oxygen demand after 5 days (BOD5...... (ADCs) were used to calculate the solid amounts of undigested nutrients. These were subsequently used for calculating the solid COD output, verified by direct COD measurements. The output of solid and suspended/dissolved BOD5 and COD was measured in the second experiment. There were just minor...

  9. Development of a field test method for total suspended solids analysis. (United States)


    Total suspended solids (TSS) are all particles in water that will not pass through a glass fiber filter with a pore size less : than 2 m, including sediments, algae, nutrients, and metals. TSS is an important water quality parameter because of its ...

  10. Characterization and morphology of solids suspended in rain water; Caracterizacion y morfologia de solidos suspendidos en agua de lluvia

    Energy Technology Data Exchange (ETDEWEB)

    Iturbe G, J.L.; Lopez M, B.E.; Torre O, J. De la [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, Mexico D.F. (Mexico)


    This work presents the results obtained from the analysis of rain water in Mexico. The study treats over the characterization and morphology of the solids suspended in form of particles in the atmosphere. The solids suspended were obtained of the pluvial precipitations after these have been centrifuged. Subsequently of the separation, the particulate matter was analysed by Sem and X-ray dispersive energy.

  11. Infrared Spectroscopy of Noh Suspended in Solid Parahydrogen: Part Two (United States)

    Balabanoff, Morgan E.; Mutunga, Fredrick M.; Anderson, David T.


    The only report in the literature on the infrared spectroscopy of the parent oxynitrene NOH was performed using Ar matrix isolation spectroscopy at 10 K. In this previous study, they performed detailed isotopic studies to make definitive vibrational assignments. NOH is predicted by high-level calculations to be in a triplet ground electronic state, but the Ar matrix isolation spectra cannot be used to verify this triplet assignment. In our 2013 preliminary report, we showed that 193 nm in situ photolysis of NO trapped in solid parahydrogen can also be used to prepare the NOH molecule. Over the ensuing two years we have been studying the infrared spectroscopy of this species in more detail. The spectra reveal that NOH can undergo hindered rotation in solid parahydrogen such that we can observe both a-type and b-type rovibrational transitions for the O-H stretch vibrational mode, but only a-type for the mode assigned to the bend. In addition, both observed a-type infrared absorption features (bend and OH stretch) display fine structure; an intense central peak with weaker peaks spaced symmetrically to both lower and higher wavenumbers. The spacing between the peaks is nearly identical for both vibrational modes. We now believe this fine structure is due to spin-rotation interactions and we will present a detailed analysis of this fine structure. Currently, we are performing additional experiments aimed at making 15NOH to test these preliminary assignments. The most recent data and up-to-date analysis will be presented in this talk. G. Maier, H. P. Reisenauer, M. De Marco, Angew. Chem. Int. Ed. 38, 108-110 (1999). U. Bozkaya, J. M. Turney, Y. Yamaguchi, and H. F. Schaefer III, J. Chem. Phys. 136, 164303 (2012). David T. Anderson and Mahmut Ruzi, 68th Ohio State University International Symposium on Molecular Spectroscopy, talk TE01 (2013).

  12. Nutrient and suspended solids removal from petrochemical wastewater via microalgal biofilm cultivation. (United States)

    Hodges, Alan; Fica, Zachary; Wanlass, Jordan; VanDarlin, Jessica; Sims, Ronald


    Wastewater derived from petroleum refining currently accounts for 33.6 million barrels per day globally. Few wastewater treatment strategies exist to produce value-added products from petroleum refining wastewater. In this study, mixed culture microalgal biofilm-based treatment of petroleum refining wastewater using rotating algae biofilm reactors (RABRs) was compared with suspended-growth open pond lagoon reactors for removal of nutrients and suspended solids. Triplicate reactors were operated for 12 weeks and were continuously fed with petroleum refining wastewater. Effluent wastewater was monitored for nitrogen, phosphorus, total suspended solids (TSS), and chemical oxygen demand (COD). RABR treatment demonstrated a statistically significant increase in removal of nutrients and suspended solids, and increase in biomass productivity, compared to the open pond lagoon treatment. These trends translate to a greater potential for the production of biomass-based fuels, feed, and fertilizer as value-added products. This study is the first demonstration of the cultivation of mixed culture biofilm microalgae on petroleum refining wastewater for the dual purposes of treatment and biomass production. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Study of Suspended Solid in Constructed Wetland Using Rare Earth Elements (United States)

    Xiao, Z. X. Z.


    Constructed wetland (CW) is one of the commonly used technologies in wastewater treatment. By means of the biochemical interactions among water, microscopic organism, aquatic plant and sediments in natural environment CW can remove biochemical oxygen demand (BOD), ammoniacal nitrogen, suspended solid (SS) and heavy metals. In this study, rare earth elements (REEs) were used as a natural tracer for the study of SS in the CW. The studied CW, Hebao Island free water surface CW, is located in Chiayi County, south Taiwan. The CW is designed for removing SS and BOD due to the pollution from livestock farms in the upstream area. However, the removal of SS was not effective. In some cases, the SS concentration of inflow is even higher than that of outflow. That the sediments on the slope were flushed into the CW was considered as the main problem. After all the refinement, the issue has not improved yet. In the study, the water samples were filtered with 1.0μm filter paper. Then, part of water samples were digested by ultrapure nitric acid to obtain the water representing the total of dissolved and suspended matters. The others were filtered by 0.1μm filter, which represent the matters in dissolved form. REEs and most of metals were subsequently measured with ICP-MS. REEs generally have a unique source and would fractionate in certain regular patterns during biochemical reactions due to lanthanide contraction. They can be an excellent natural tracer in the environmental researches. After normalized by North American Shale Composite, the REEs pattern for the samples with the total of dissolved and suspended matters is characterized by a middle REE (MREE) enrichment and light REE (LREE) depletion. According to the previous theoretical studies, the MREE enrichment could be achieved by a selected adsorption of MREEs by organic matters, which is generally humic substance in natural surface water. It is suggested that the refinement of removal efficiency of SS should focus on

  14. Spatial and temporal variability of suspended-sediment concentrations in a shallow estuarine environment

    Directory of Open Access Journals (Sweden)

    Catherine A. Ruhl


    Full Text Available Shallow subembayments respond differently than deep channels to physical forces acting in estuaries. The U.S. Geological Survey measured suspended-sediment concentrations at five locations in Honker Bay, a shallow subembayment of San Francisco Bay, and the adjacent channel to investigate the spatial and temporal differences between deep and shallow estuarine environments. During the first freshwater pulse of the wet season, the channel tended to transport suspended sediments through the system, whereas the shallow area acted as off-channel storage where deposition would likely occur. Following the freshwater pulse, suspended-sediment concentrations were greater in Honker Bay than in the adjacent deep channel, due to the larger supply of erodible sediment on the bed. However, the tidal variability of suspended-sediment concentrations in both Honker Bay and in the adjacent channel was greater after the freshwater pulse than before. During wind events, suspended-sediment concentrations in the channel were not affected; however, wind played a crucial role in the resuspension of sediments in the shallows. Despite wind-wave sediment resuspension in Honker Bay, tidally averaged suspended-sediment flux was controlled by the flood-dominated currents.

  15. Electrodialytic extraction of Cu, Pb and Cl from municipal solid waste incineration fly ash suspended in water

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Lima, Ana Teresa; Pedersen, Anne Juul


    The possibility of using fly ash from municipal solid waste incineration (MSWI) in, for example, concrete is considered. MSWI fly ash, however, has too high a concentration of heavy metals, which may cause leaching problems during use or problems with waste handling at the end of the lifetime...... of the concrete. The Cl content in MSWI fly ash is also too high and will cause corrosion problems in reinforced concrete. The possibility of removing some of the unwanted heavy metals (Cu and Pb) together with Cl from an MSWI fly ash suspended in water using an electrodialytic separation method was investigated...

  16. Loads of nitrate, phosphorus, and total suspended solids from Indiana watersheds (United States)

    Bunch, Aubrey R.


    Transport of excess nutrients and total suspended solids (TSS) such as sediment by freshwater systems has led to degradation of aquatic ecosystems around the world. Nutrient and TSS loads from Midwestern states to the Mississippi River are a major contributor to the Gulf of Mexico Hypoxic Zone, an area of very low dissolved oxygen concentration in the Gulf of Mexico. To better understand Indiana’s contribution of nutrients and TSS to the Mississippi River, annual loads of nitrate plus nitrite as nitrogen, total phosphorus, and TSS were calculated for nine selected watersheds in Indiana using the load estimation model, S-LOADEST. Discrete water-quality samples collected monthly by the Indiana Department of Environmental Management’s Fixed Stations Monitoring Program from 2000–2010 and concurrent discharge data from the U. S. Geological Survey streamflow gages were used to create load models. Annual nutrient and TSS loads varied across Indiana by watershed and hydrologic condition. Understanding the loads from large river sites in Indiana is important for assessing contributions of nutrients and TSS to the Mississippi River Basin and in determining the effectiveness of best management practices in the state. Additionally, evaluation of loads from smaller upstream watersheds is important to characterize improvements at the local level and to identify priorities for reduction.

  17. Geospatial approach towards enumerative analysis of suspended sediment concentration for Ganges-Brahmaputra Bay (United States)

    Pandey, Palak; Kunte, Pravin D.


    This study presents an easy, modular, user-friendly, and flexible software package for processing of Landsat 7 ETM and Landsat 8 OLI-TIRS data for estimating suspended particulate matter concentrations in the coastal waters. This package includes 1) algorithm developed using freely downloadable SCILAB package, 2) ERDAS Models for iterative processing of Landsat images and 3) ArcMAP tool for plotting and map making. Utilizing SCILAB package, a module is written for geometric corrections, radiometric corrections and obtaining normalized water-leaving reflectance by incorporating Landsat 8 OLI-TIRS and Landsat 7 ETM+ data. Using ERDAS models, a sequence of modules are developed for iterative processing of Landsat images and estimating suspended particulate matter concentrations. Processed images are used for preparing suspended sediment concentration maps. The applicability of this software package is demonstrated by estimating and plotting seasonal suspended sediment concentration maps off the Bengal delta. The software is flexible enough to accommodate other remotely sensed data like Ocean Color monitor (OCM) data, Indian Remote Sensing data (IRS), MODIS data etc. by replacing a few parameters in the algorithm, for estimating suspended sediment concentration in coastal waters.

  18. Experimental Design of Electrocoagulation and Magnetic Technology for Enhancing Suspended Solids Removal from Synthetic Wastewater

    Directory of Open Access Journals (Sweden)

    Moh Faiqun Ni'am


    Full Text Available Design of experiments (DOE is one of the statistical method that is used as a tool to enhance and improve experimental quality. The changes to the variables of a process or system is supposed to give the optimal result (response and quite satisfactory. Experimental design can defined as a test or series of test series by varying the input variables (factors of a process that can known to cause changes in output (response. This paper presents the results of experimental design of wastewater treatment by electrocoagulation (EC technique. A combined magnet and electrocoagulation (EC technology were designed to increase settling velocity and to enhance suspended solid removal efficiencies from wastewater samples. In this experiment, a synthetic wastewater samples were prepared by mixing 700 mg of the milk powder in one litre of water and treated by using an acidic buffer solution. The monopolar iron (Fe plate anodes and cathodes were employed as electrodes. Direct current was varied in a range of between 0.5 and 1.1 A, and flowrate in a range of between 1.00 to 3.50 mL/s. One permanent magnets namely AlNiCo with a magnetic strength of 0.16T was used in this experiment. The results show that the magnetic field and the flowrate have major influences on suspended solids removal. The efficiency removals of suspended solids, turbidity and COD removal efficiencies at optimum conditions were found to be more than 85%, 95%, and 75%, respectively.

  19. Spatial and Temporal Dynamics of Fecal Coliform and Associated with Suspended Solids and Water within Five Northern California Estuaries. (United States)

    Lewis, David J; Atwill, Edward R; Pereira, Maria das Graças C; Bond, Ronald


    Fecal coliform and associated with suspended solids (SS) and water in five northern California estuaries were studied to document process influences and water quality monitoring biases affecting indicator bacteria concentrations. We collected and analyzed 2371 samples during 10 sampling events for the five studied estuaries. Concentrations during wet-season stormflow conditions were greater than during wet-season base flow and dry-season base flow conditions. Results also document concentration gradients across the length of the studied estuaries and with depth of sample collection. Highest concentrations were associated with shallow samples collected furthest inland. Corresponding decreases occurred the deeper and closer to the estuary mouth a sample was collected. Results also identify direct relationships of wind speed and discharge velocity and indirect relationship of tide stage to indicator bacteria concentrations. Bacteria associated with suspended solids (SS), after conversion to the same units of measurement (mass), were three orders of magnitude greater than in the water fraction. However, the mean proportion contributed by SS to composite water sample concentrations was 8% (SE 0.3) for fecal coliform and 7% (SE 0.3) for . Bacteria from the SS proportion is related to seasonality, tide stage, and discharge velocity that are consistent with mechanisms for entrainment, transport of SS, and reduced particle settling. These results are important for both managing and monitoring these systems by improving sample spatial and temporal context and corresponding bacteria concentration values across the freshwater-saltwater interface. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  20. Occurrence and persistence of fungicides in bed sediments and suspended solids from three targeted use areas in the United States. (United States)

    Smalling, Kelly L; Reilly, Timothy J; Sandstrom, Mark W; Kuivila, Kathryn M


    To document the environmental occurrence and persistence of fungicides, a robust and sensitive analytical method was used to measure 34 fungicides and an additional 57 current-use pesticides in bed sediments and suspended solids collected from areas of intense fungicide use within three geographic areas across the United States. Sampling sites were selected near or within agricultural research farms using prophylactic fungicides at rates and types typical of their geographic location. At least two fungicides were detected in 55% of the bed and 83% of the suspended solid samples and were detected in conjunction with herbicides and insecticides. Six fungicides were detected in all samples including pyraclostrobin (75%), boscalid (53%), chlorothalonil (41%) and zoxamide (22%). Pyraclostrobin, a strobilurin fungicide, used frequently in the United States on a variety of crops, was detected more frequently than p,p'-DDE, the primary degradate of p,p'-DDT, which is typically one of the most frequently occurring pesticides in sediments collected within highly agricultural areas. Maximum fungicide concentrations in bed sediments and suspended solids were 198 and 56.7 μg/kg dry weight, respectively. There is limited information on the occurrence, fate, and persistence of many fungicides in sediment and the environmental impacts are largely unknown. The results of this study indicate the importance of documenting the persistence of fungicides in the environment and the need for a better understanding of off-site transport mechanisms, particularly in areas where crops are grown that require frequent treatments to prevent fungal diseases. Published by Elsevier B.V.

  1. Field calibration of optical sensors for measuring suspended sediment concentration in the western Mediterranean

    Directory of Open Access Journals (Sweden)

    J. Guillén


    Full Text Available The water turbidity measured with optical methods (transmittance and backscattering is usually expressed as beam attenuation coefficient (BAC or formazin turbidity units (FTU. The transformation of these units to volumetric suspended sediment concentration (SSC units is not straightforward, and accurate calibrations are required in order to obtain valuable information on suspended sediment distributions and fluxes. In this paper, data from field calibrations between BAC, FTU and SSC are presented and best-fit calibration curves are shown. These calibrations represent an average from different marine environments of the western Mediterranean (from estuary to continental slope. However, the general curves can only be applied for descriptive or semi-quantitative purposes. Comparison of turbidity measurements using the same sensor with different calibration ranges shows the advantage of simultaneously combining two instruments calibrated in different ranges when significant changes in suspended sediment concentrations are expected.

  2. Nutrients and Suspended Solids in Surface Waters of the Upper Illinois River Basin in Illinois, Indiana, and Wisconsin, 1978-97 (United States)

    Sullivan, Daniel J.


    A retrospective analysis of selected data on nutrients and suspended solids in surface waters of the upper Illinois River Basin was done as part of the U.S. Geological Survey (USGS) National Water-Quality Assessment (NAWQA) Program. Approximately 91 percent of the upper Illinois River Basin is drained by three principal rivers: the Kankakee (and its major tributary, the Iroquois), the Des Plaines, and the Fox. The data analyzed were collected by the Illinois Environmental Protection Agency (IEPA), which operates 39 monitoring sites in the study area as part of its Ambient Water-Quality Monitoring Network, and included analyses for total ammonia nitrogen, total nitriteplus- nitrate nitrogen, total ammonia-plus-organic (total Kjeldahl) nitrogen, dissolved and total phosphorus, and total suspended solids and volatile solids. Nutrient and suspended-sediment data collected by the USGS as part of the upper Illinois River Basin NAWQA pilot study from 1987-90 were compared to IEPA data. For the 1978-97 period, in general, nutrient concentrations, with the exception of nitrate, were highest at streams in the urban areas of the Des Plaines River Basin. Streams in the Kankakee and Fox River Basins generally had lower concentrations, although the data indicate that concentrations increased in a downstream direction in these basins. These spatial patterns in nutrient concentrations correspond closely with land use in the respective basins. The elevated concentrations of ammonia and phosphorus in the urbanized Des Plaines River Basin, with respect to other sites in the study area, indicate that municipal- and industrial- waste discharges into streams of the basin increase concentrations of these nutrients in the receiving streams. In contrast, nitrate concentrations were highest in agricultural areas. Relatively large ratios of nitrogen to phosphorus and nitrate to ammonia are characteristic of agricultural drainage. On the other hand, urban tributaries were characterized by

  3. Feedbacks between bivalve density, flow, and suspended sediment concentration on patch stable states. (United States)

    Coco, Giovanni; Thrush, Simon F; Green, Malcolm O; Hewitt, Judi E


    We explore the role of biophysical feedbacks occurring at the patch scale (spatial scale of tens of meters) that influence bivalve physiological condition and affect patch stability by developing a numerical model for the pinnid bivalve, Atrina zelandica, in cohesive sediments. Simulated feedbacks involve bivalve density, flow conditions (assumed to be primarily influenced by local water depth and peak current speed), suspended sediment concentration (evaluated through a balance between background concentration, deposition, and erosion), and changes in the physiology of Atrina derived from empirical study. The model demonstrates that high bivalve density can lead to skimming flow and to a concomitant decrease in resuspension that will affect suspended sediment concentration over the patch directly feeding back on bivalve physiology. Consequently, for a given flow and background suspended sediment load, the stability of a patch directly depends on the size and density of bivalves in the patch. Although under a range of conditions patch stability is ensured independently of bivalve density, simulations clearly indicate that sudden changes in bivalve density or suspended sediment concentration can substantially affect patch structure and lead to different stable states. The model highlights the role of interactions between organisms, flow, and broader scale environmental conditions in providing a mechanistic explanation for the patchy occurrence of benthic suspension feeders.

  4. Estimating total suspended matter concentration in tropical waters of the Berau estuary, Indonesia

    NARCIS (Netherlands)

    Ambarwulan, W.; Verhoef, W.; Mannaerts, C.M.; Salama, M.S.


    This study presents the application of a semi-empirical approach, based on the Kubelka–Munk (K-M) model, to retrieve the total suspended matter (TSM) concentration of water bodies from ocean colour remote sensing. This approach is validated with in situ data sets compiled from the tropical waters of

  5. Spatio-temporal Analysis of suspended sediment Concentration in the Yongjiang Estuary Based on GOCI (United States)

    Kang, Yanyan; Dong, Chuan


    The concentration and spatio-temporal variation of suspended sediment concentration in the estuary area are of great significance to the nearshore engineering, port construction and coastal evolution. Based on multi-period GOCI images and corresponding measured suspended sediment concentration (SSC) data, three inversion models (the linear regression model, the power exponent model and the neural network model) were established after rapid atmospheric correction. The results show that the absolute error of the three models is 0.20, 0.16 and 0.10kg/m3 respectively, and the relative errors are 38%, 23% and 18% respectively. The accuracy of the neural network (8-17-17-1) is the best. The SSC distribution diagrams in an ebb and flow cycle are obtained using this ANN model. The results show that with Yongjiang estuary for segmentation, the high concentration area is located in the north and the lower is in the south around Jintang Island deeper water area. When the tide rises, the water flow disturbs a large amount of sediment, and then the sediment concentration increases and high area high concentrations water body moves along the SE-NW. When the tide falls, flow rate decreases and the sediment concentration decreases. However, with the falling tide, the concentration of suspended sediment in the northern sea areas gradually increases, and is higher than 1kg/m3, and gradually moves along the NW-SE until to the estuary.

  6. Concentration Measurements of Suspended Load using ADV with Influence of the Particle Size (United States)

    Schwarzwälder, Kordula


    ADV backscatter data can be used under certain conditions to gain information about the concentrations of suspended loads. This was shown in many studies before (Fugate and Friedrichs 2002; Chanson et al 2008; Ha et al. 2009). This paper reports on a pre-study to investigate the influence of particle size on concentration measurements for suspended sediment load with ADV. The study was conducted in a flume in the Oskar-von-Miller-Institute using fresh water from a river including the natural suspended load. The ADV used in the experiments was a Vectrino Profiler (Nortek). In addition water samples were taken for TSS and TOC. For the measurements a surge was generated in the flume to ensure that also particles of larger size will be present in the water phase. The measurements and samples were taken during the whole surge event. Therefore we were able to find a good correlation between the backscatter data of the ADV and the TSS as well as TOC results. For the decreasing part of the flow event the concentration of TOC in the suspended load of the water phase is decreasing much slower than the TSS and results in a damped decrease of the backscatter values. This means that the results for concentration measurements might be slightly influenced by the size of the particles. Further evaluations of measurements conducted with a LISST SL (Sequoia) will be investigated to show the trend of the particle sizes during this process and fortify this result. David C. Fugate, Carl T. Friedrichs, Determining concentration and fall velocity of estuarine particle populations using ADV, OBS and LISST, Continental Shelf Research, Volume 22, Issues 11-13, 2002 H.K. Ha, W.-Y. Hsu, J.P.-Y. Maa, Y.Y. Shao, C.W. Holland, Using ADV backscatter strength for measuring suspended cohesive sediment concentration, Continental Shelf Research, Volume 29, Issue 10, 2009 Hubert Chanson, Maiko Takeuchi, Mark Trevethan, Using turbidity and acoustic backscatter intensity as surrogate measures of

  7. Trends in Streamflow and Nutrient and Suspended-Sediment Concentrations and Loads in the Upper Mississippi, Ohio, Red, and Great Lakes River Basins, 1975-2004 (United States)

    Lorenz, David L.; Robertson, Dale M.; Hall, David W.; Saad, David A.


    Many actions have been taken to reduce nutrient and suspended-sediment concentrations and the amount of nutrients and sediment transported in streams as a result of the Clean Water Act and subsequent regulations. This report assesses how nutrient and suspended-sediment concentrations and loads in selected streams have changed during recent years to determine if these actions have been successful. Flow-adjusted and overall trends in concentrations and trends in loads from 1993 to 2004 were computed for total nitrogen, dissolved ammonia, total organic nitrogen plus ammonia, dissolved nitrite plus nitrate, total phosphorus, dissolved phosphorus, total suspended material (total suspended solids or suspended sediment), and total suspended sediment for 49 sites in the Upper Mississippi, Ohio, Red, and Great Lakes Basins. Changes in total nitrogen, total phosphorus, and total suspended-material loads were examined from 1975 to 2003 at six sites to provide a longer term context for the data examined from 1993 to 2004. Flow-adjusted trends in total nitrogen concentrations at 19 of 24 sites showed tendency toward increasing concentrations, and overall trends in total nitrogen concentrations at 16 of the 24 sites showed a general tendency toward increasing concentrations. The trends in these flow-adjusted total nitrogen concentrations are related to the changes in fertilizer nitrogen applications. Flow-adjusted trends in dissolved ammonia concentrations from 1993 to 2004 showed a widespread tendency toward decreasing concentrations. The widespread, downward trends in dissolved ammonia concentrations indicate that some of the ammonia reduction goals of the Clean Water Act are being met. Flow-adjusted and overall trends in total organic plus ammonia nitrogen concentrations from 1993 to 2004 did not show a distinct spatial pattern. Flow-adjusted and overall trends in dissolved nitrite plus nitrate concentrations from 1993 to 2004 also did not show a distinct spatial pattern

  8. Plutonium removal and diurnal variations of suspended sediment concentrations in the Great Miami River

    Energy Technology Data Exchange (ETDEWEB)

    Bobula, III, C. M.; Kennedy, C. W.; Bartelt, G. E.


    Effluent release experiments previously conducted downstream of the industrial outflal at Mound Laboratory have demonstrated that /sup 238/Pu which enters the aquatic environment as dissolved waste is rapidly adsorbed by suspended solids in the effluent pulse and that the dissolved/particulate distribution of /sup 238/Pu between release events congruent to 5 x 10/sup -2/./sup 3/ Reasonable estimates of the annual transport of /sup 239/ /sup 240/Pu based upon long-term discharge and sediment loading data have been reported for a large subwatershed in the upper reaches of the Great Miami River Basin. In this report data are given which characterize the short-term variability of suspended particulate transport downriver of a canal system contaminated with /sup 238/Pu.

  9. Temporal and spatial variations in total suspended and dissolved solids in the upper part of Manoa stream, Hawaii

    NARCIS (Netherlands)

    Augustijn, Dionysius C.M.; Fares, Ali; Tran, Dai Ngia


    Hawaiian watersheds are small, steep, and receive high intensity rainfall events of non-uniform distribution. These geographic and weather patterns result in flashy streams of strongly variable water quality even within various stream segments. Total suspended solids (TSS) and total dissolved solids

  10. A Comparison of Suspended Solids Sediment and Turbidity from MODIS and MERIS Imagery in the Three Gorges Dam Area, China (United States)

    Di Trapani, Antonio; Corbari, Chiara; Mancini, Marco


    The aim of this work is to evaluate turbidity magnitude and total suspended matter (TSM) concentrations of the Three Gorges Reservoir, China, applying different retrieval algorithms to satellite imagery (MOD09GQ and MERIS FRS L2) 250 m: turbidity and TSM values retrieved from the satellite scenes were correlated to discharge values measured daily on the ground, leading to relations between TSM and discharge. Applying the obtained relations to the discharge dataset made possible to have daily estimations of TSM values even for the days for which satellite scenes were lacking. The estimations from the various retrieval algorithms and sediment discharge values were compared with literature values of solid discharge measured on the ground.

  11. The effect of light direction and suspended cell concentrations on algal biofilm growth rates. (United States)

    Schnurr, Peter J; Espie, George S; Allen, D Grant


    Algae biofilms were grown in a semicontinuous flat plate biofilm photobioreactor to study the effects of light direction and suspended algal cell populations on algal biofilm growth. It was determined that, under the growth conditions and biofilm thicknesses studied, light direction had no effect on long-term algal biofilm growth (26 days); however, light direction did affect the concentration of suspended algal cells by influencing the photon flux density in the growth medium in the photobioreactors. This suspended algal cell population affected short-term (7 days) algae cell recruitment and algal biofilm growth, but additional studies showed that enhanced suspended algal cell populations did not affect biofilm growth rates over the long term (26 days). Studying profiles of light transmittance through biofilms as they grew showed that most of the light became attenuated by the biomass after just a few days of growth (88 % after 3 days). The estimated biofilm thicknesses after these few days of growth were approximately 150 μm. The light attenuation data suggests that, although the biofilms grew to 700-900 μm, under these light intensities, only the first few hundred micrometers of the biofilm is receiving enough light to be photosynthetically active. We postulate that this photosynthetically active layer of the biofilm grows adjacent to the light source, while the rest of the biofilm is in a stationary growth phase. The results of this study have implications for algal biofilm photobioreactor design and operation.

  12. Avaliação da concentração de mercúrio em sedimentos e material particulado no rio Acre, estado do Acre, Brasil Mercury concentration assessment in botton sediments and suspended solids from Acre river, in the State of Acre, Brazil

    Directory of Open Access Journals (Sweden)

    Artur Fernando Silva Mascarenhas


    Full Text Available A avaliação dos teores de mercúrio em sistemas aquáticos sem influência direta de fontes antropogênicas conhecidas não tem sido conduzida com freqüência na região Amazônica. Visando contribuir para esclarecer a ocorrência de valores elevados de Hg em peixes consumidos pela população de Rio Branco - AC, o Instituto Evandro Chagas - IEC, realizou um estudo para quantificar os teores de Hg em sedimentos de fundo e material particulado no rio Acre e alguns afluentes, além da caracterização físico-química das águas entre as cidades de Brasiléia e Assis Brasil. As amostras de sedimentos foram peneiradas na fração Mercury levels assessment in aquatic systems areas without influences of antropogenic sources have not been well studied in the Amazon region. For the identification of the origin of high values of Hg in fish consumed by population of Rio Branco City - AC, the Evandro Chagas Institute - IEC, studied the mercury levels in sediments, suspended solids and studied also the physical-chemical characterization of waters, in the Acre river and also some in afluents, between Brasiléia and Assis Brasil cities. Bottom sediments samples were sieved to <250 mesh fraction after drying. The suspended solid was obtained by precipitation with Al2SO4. About 250 mg of the material was submitted the acid digestion and the determinations of Hg were made by Could Vapor Atomic Absorption Spectrometry. The physical-chemical parameters pH, electric conductivity, temperature and dissolved total solids, were studied in the field, by potenciometric methods. The Hg levels in bottom sediments range 0,018 and 0,184 mug g-1, mean of 0,054 ± 0,034 mug g-1, while the suspended solids varied between 0,067 and 0,220 mug g-1, average of 0,098 ± 0,037 mug g-1. The waters were slightly acid with pH varying among 5,80 - 6,95 and conductivity electric 151,60 - 1.151,00 muS cm-1. The mercury levels in the analyzed materials was below of standard levels for

  13. Longitudinal trends and discontinuities in nutrients, chlorophyll, and suspended solids in the Upper Mississippi River: Implications for transport, processing, and export by large rivers (United States)

    Houser, J.N.; Bierman, D.W.; Burdis, R.M.; Soeken-Gittinger, L. A.


    Across the distances spanned by large rivers, there are important differences in catchment characteristics, tributary inputs, and river morphology that may cause longitudinal changes in nutrient, chlorophyll, and suspended solids concentrations. We investigated longitudinal and seasonal patterns in the Upper Mississippi River (UMR) using long-term data (1994-2005) from five study reaches that spanned 1300 km of the UMR. Lake Pepin, a natural lake in the most upstream study reach, had a clear effect on suspended material in the river. Suspended solids and total phosphorus (TP) concentrations were substantially lower downstream of the lake and percent organic material (OM%) in suspension was higher. Below L. Pepin, mean total and organic suspended solids (TSS, OSS) and TP increased downriver and exhibited approximately log-linear relationships with catchment area, whereas OM% declined substantially downriver. Despite the downriver increase in TSS and OSS, concentrations similar to those above L. Pepin do not occur until ~370 km downriver indicating the extent of the influence of L. Pepin on the UMR. Chlorophyll concentrations were lower in the most downstream study reach, likely reflecting the shorter residence time and poor light climate, but there was not a consistent longitudinal decline in chlorophyll across the study reaches. Dissolved silica (DSi), DSi:TN, and DSi:TP declined downriver suggesting that DSi uptake and sedimentation by river phytoplankton may be reducing DSi transport in the river, and indicating that the eutrophication of the river may contribute to a reduction of DSi export to the Gulf of Mexico. ?? 2010 US Government: USGS.

  14. Sediment Size Effects in Acoustic Doppler Velocimeter-Derived Estimates of Suspended Sediment Concentration

    Directory of Open Access Journals (Sweden)

    Mehmet Öztürk


    Full Text Available Backscatter output from a 10 MHz acoustic Doppler velocimeter (ADV was used to quantify suspended sediment concentrations in a laboratory setting using sand-sized particles. The experiments included (a well-sorted sand samples ranging in size from 0.112 to 0.420 mm, obtained by the sieving of construction sand, (b different, known mixtures of these well-sorted fractions, and (c sieved natural beach sand with median sizes ranging from 0.112 to 0.325 mm. The tested concentrations ranged from 25 to 3000 mg•L−1. The backscatter output was empirically related to concentration and sediment size, and when non-dimensionalized by acoustic wavelength, a dimensionless sediment size gradation coefficient. Size-dependent upper and lower bounds on measurable concentrations were also established empirically. The range of measurable conditions is broad enough to make the approach useful for sand sizes and concentrations commonly encountered in nature. A new method is proposed to determine concentrations in cases of mixed-size sediment suspensions when only calibration data for well-sorted constituent sands are available. This approach could potentially allow better estimates when the suspended load is derived from but is not fully representative of the bed material, and when the size characteristics of the suspended material are varying in time over the period of interest. Differences in results between the construction and beach sands suggest that sediment shape may also need to be considered, and point to the importance of calibrating to sediments encountered at the site of interest.

  15. Suspended solids and nutrient retention in rural constructed wetlands in cold climate (United States)

    Koskiaho, Jari; Siimekselä, Tiina; Puustinen, Markku


    Three constructed wetlands (CWs), two located in southern and one in central Finland, were monitored during 2013-2015. The southern CWs Hovi (0.6 ha wet area) and Rantamo-Seitteli (24 ha wet area) were monitored continuously by s::can nitro::lyser ( sensors. On average 10 pairs (inflow and outflow) of water samples were annually taken in the two southern CWs and 20 pairs in the northernmost Tarvaala CW (wet area 1.4 ha). In Tarvaala, a portable, continuously measuring Micromac 1000 -phosphate analyzer ( was also tested at the CW outlet in 2015. The CWs differed in their size, dimensioning (CW-to-catchment area ratio) and in the characteristics of their upstream catchments. The Hovi CW has 5.0% CW-to-catchment area ratio and 100% agricultural land use in its clayey catchment. The corresponding percentages were for the Rantamo-Seitteli CW (clayey catchment) 1.3% and 42%, and for the Tarvaala CW (coarse soil type in the catchment) 1.0% and 16%. The average annual total suspended solids (TSS) retentions in Hovi, Rantamo-Seitteli and Tarvaala CWs were 79%, 6% and 50%, respectively. The average annual total phosphorus (TP) retentions were 61% at Hovi, 22% at Rantamo-Seitteli and 23% at Tarvaala. The unexpectedly high TSS and TP retentions at Tarvaala were probably due to the coarse soil type with more readily settling particles than in two other CWs. In Hovi and Rantamo-Seitteli CWs also dissolved reactive phosphorus (DRP) was measured. The DRP retentions (83% at Hovi and 27% at Rantamo-Seitteli) were higher than those of TP, which was probably due to the high contents of P-binding Al- and Fe-oxides in the soil of these two CWs. In the Hovi CW, vivid biological activity (abundant vegetation, algae and microbes) might also have played a role. The average annual total nitrogen (TN) retentions in Hovi and Rantamo-Seitteli CWs were 66% and 14%, respectively. At Tarvaala, TN retention varied annually so that no net retention over the whole period

  16. Influence of sampling intake position on suspended solid measurements in sewers: two probability/time-series-based approaches. (United States)

    Sandoval, Santiago; Bertrand-Krajewski, Jean-Luc


    Total suspended solid (TSS) measurements in urban drainage systems are required for several reasons. Aiming to assess uncertainties in the mean TSS concentration due to the influence of sampling intake vertical position and vertical concentration gradients in a sewer pipe, two methods are proposed: a simplified method based on a theoretical vertical concentration profile (SM) and a time series grouping method (TSM). SM is based on flow rate and water depth time series. TSM requires additional TSS time series as input data. All time series are from the Chassieu urban catchment in Lyon, France (time series from 2007 with 2-min time step, 89 rainfall events). The probability of measuring a TSS value lower than the mean TSS along the vertical cross section (TSS underestimation) is about 0.88 with SM and about 0.64 with TSM. TSM shows more realistic TSS underestimation values (about 39 %) than SM (about 269 %). Interquartile ranges (IQR) over the probability values indicate that SM is more uncertain (IQR = 0.08) than TSM (IQR = 0.02). Differences between the two methods are mainly due to simplifications in SM (absence of TSS measurements). SM assumes a significant asymmetry of the TSS concentration profile along the vertical axis in the cross section. This is compatible with the distribution of TSS measurements found in the TSM approach. The methods provide insights towards an indicator of the measurement performance and representativeness for a TSS sampling protocol.

  17. Present and Reference Concentrations and Yields of Suspended Sediment in Streams in the Great Lakes Region and Adjacent Areas (United States)

    Robertson, Dale M.; Saad, David A.; Heisey, Dennis M.


    In-stream suspended sediment and siltation and downstream sedimentation are common problems in surface waters throughout the United States. The most effective way to improve surface waters impaired by sediments is to reduce the contributions from human activities rather than try to reduce loadings from natural sources. Total suspended sediment/solids (TSS) concentration data were obtained from 964 streams in the Great Lakes, Ohio, Upper Mississippi, and Souris-Red-Rainy River Basins from 1951 to 2002. These data were used to estimate median concentrations, loads, yields, and volumetrically (flow) weighted (VW) concentrations where streamflow data were available. SPAtial Regression-Tree Analysis (SPARTA) was applied to land-use-adjusted (residualized) TSS data and environmental-characteristic data to determine the natural factors that best described the distribution of median and VW TSS concentrations and yields and to delineate zones with similar natural factors affecting TSS, enabling reference or natural concentrations and yields to be estimated. Soil properties (clay and organic-matter content, erodibility, and permeability), basin slope, and land use (percentage of agriculture) were the factors most strongly related to the distribution of median and VW TSS concentrations. TSS yields were most strongly related to amount of precipitation and the resulting runoff, and secondarily to the factors related to high TSS concentrations. Reference median TSS concentrations ranged from 5 to 26 milligrams per liter (mg/L), reference median annual VW TSS concentrations ranged from 10 to 168 mg/L, and reference TSS yields ranged from about 980 to 90,000 kilograms per square kilometer per year. Independent streams (streams with no overlapping drainage areas) with TSS data were ranked by how much their water quality exceeded reference concentrations and yields. Most streams exceeding reference conditions were in the central part of the study area, where agricultural activities

  18. Influence of Rainfall Characteristics on Total Suspended Solids in Urban Runoff: A Case Study in Beijing, China

    Directory of Open Access Journals (Sweden)

    Yongwei Gong


    Full Text Available An urban rainfall-runoff water quality model was developed to simulate total suspend solids (TSS using the stormwater management model (SWMM for a 3.8 ha university campus in Beijing (approximately 76.5% impervious, and calibrated and validated against data from two observed rainfall events (221.2 and 16.6 mm rainfall. Model performance is satisfactory (Nash–Sutcliffe model efficiency 0.8 and 0.72 for flow and 0.74 and 0.51 for TSS concentration, respectively. A series of sensitivity model runs were conducted using the calibrated SWMM to study the influences of rainfall characteristics (rainfall hyetographs, depths and durations and surface flooding on the TSS concentration in outlet runoff of the catchment. The Pilgrim and Cordery rainfall distribution defines a first-quartile storm (the most severe and results in the highest peak discharge and TSS concentration at the outlet but the lowest outlet TSS load because of the highest TSS flood loss (32.3%. The simulated TSS pollutograph resulting from the Keifer and Chu rainfall distribution (with r = 0.5 is almost identical to that resulting from the alternating block rainfall distribution. Under the same rainfall hyetograph, simulated peak discharge and outlet TSS load are positively correlated (R2 = 0.95 to the rainfall depth as a function of the return period.

  19. Suspended sediment concentration and optical property observations of mixed-turbidity, coastal waters through multispectral ocean color inversion (United States)

    Multispectral satellite ocean color data from high-turbidity areas of the coastal ocean contain information about the surface concentrations and optical properties of suspended sediments and colored dissolved organic matter (CDOM). Empirical and semi-analytical inversion algorit...

  20. Estimation on the concentration of total suspended matter in Lombok Coastal using Landsat 8 OLI, Indonesia (United States)

    Emiyati; Manoppo, Anneke K. S.; Budhiman, Syarif


    Total Suspended Matter (TSM) are fine materials which suspended and floated in water column. Water column could be turbid due to TSM that reduces the depth of light penetration and causes low productivity in coastal waters. The objective of this study was to estimate TSM concentration using Landsat 8 OLI data in Lombok coastal waters Indonesia by using empirical and analytic approach between three visible bands of Landsat 8 OLI subsurface reflectance (OLI 2, OLI 3 and OLI 4) and field data. The accuracy of model was tested using error estimation and statistical analysis. Colour of waters, transparency and reflectance values showed, the clear water has high transparency and low reflectance while the turbid waters have low transparency and high reflectance. The estimation of TSM concentrations in Lombok coastal waters are 0.39 to 20.7 mg/l. TSM concentrations becoming high when it is on coast and low when it is far from the coast. The statistical analysis showed that TSM model from Landsat 8 OLI data could describe TSM from field measurement with correlation 91.8% and RMSE value 0.52. The t-test and f-test showed that the TSM derived from Landsat 8 OLI and TSM measured in field were not significantly different.

  1. Empirical model for estimating vertical concentration profiles of re-suspended, sediment-associated contaminants (United States)

    Zhu, H. W.; Cheng, P. D.; Li, W.; Chen, J. H.; Pang, Y.; Wang, D. Z.


    Vertical distribution processes of sediment contaminants in water were studied by flume experiments. Experimental results show that settling velocity of sediment particles and turbulence characteristics are the major hydrodynamic factors impacting distribution of pollutants, especially near the bottom where particle diameter is similar in size to vortex structure. Sediment distribution was uniform along the distance, while contaminant distribution slightly lagged behind the sediment. The smaller the initial sediment concentration was, the more time it took to achieve a uniform concentration distribution for suspended sediment. A contaminants transportation equation was established depending on mass conservation equations. Two mathematical estimation models of pollutant distribution in the overlying water considering adsorption and desorption were devised based on vertical distribution of suspended sediment: equilibrium partition model and dynamic micro-diffusion model. The ratio of time scale between the sediment movement and sorption can be used as the index of the models. When this ratio was large, the equilibrium assumption was reasonable, but when it was small, it might require dynamic micro-diffusion model.

  2. Analysing the correlations of long-term seasonal water quality parameters, suspended solids and total dissolved solids in a shallow reservoir with meteorological factors. (United States)

    Zhang, Chen; Zhang, Wenna; Huang, Yixuan; Gao, Xueping


    To explore the correlations among water quality parameters, suspended solids (SS) and total dissolved solids (TDS) with meteorological factors in a shallow reservoir in China, the long-term variations of water quality were considered. A non-parametric regression method, generalized additive models (GAM), was used to analyse the correlations among eleven physicochemical and biological parameters as well as three meteorological factors (wind speed, rainfall and solar radiation) which we collected from 2000 to 2011. The results indicate that the three meteorological factors may have positive effects on SS. Moreover, statistically significant correlations between many water quality parameters and SS or TDS were exhibited seasonally. The correlations between electrical conductivity (EC) and SS were opposite to correlations between EC and TDS. This finding reveals that TDS have a positive impact on EC, while EC negatively affects SS. The results indicated that many parameters, such as total nitrogen, total phosphorus, biological oxygen demand (BOD) and chemical oxygen demand (COD), were related to SS due to the adsorption of SS. Moreover, both positive and negative correlations between COD and TDS were observed in this freshwater reservoir. The positive correlation between chlorophyll a and SS suggested that the change of SS concentration in autumn was caused by the growth of algae. Meanwhile, significant correlations between SS and meteorological factors were also observed, indicating that meteorological factors had effects on SS dynamics. This study provides useful information regarding the correlations among water quality parameters, SS and TDS with meteorological factors in a freshwater reservoir.

  3. Study on submerged anaerobic membrane bioreactor (SAMBR) treating high suspended solids raw tannery wastewater for biogas production. (United States)

    Umaiyakunjaram, R; Shanmugam, P


    This study deals with the treatment of high suspended solids raw tannery wastewater using flat sheet Submerged Anaerobic Membrane (0.4μm) Bioreactor (SAMBR) acclimatized with hypersaline anaerobic seed sludge for recovering biogas. The treatability of SAMBR achieved higher CODremoval efficiency (90%) and biogas yield (0.160L.g(-1) CODremoved) coincided with high r(2) values between permeate flux and TSS (0.95), biogas and COD removed (0.96). The acidification of hypersaline influent wastewater by biogas mixing with high CO2, achieved quadruplet benefit of gas liquid and solid separation, in-situ pH and NH3 control, in-situ CH4 enrichment, and prevention of membrane fouling. The initial high VFA became stable as time elapsed reveals the hydrolysing ability of particulate COD into soluble COD and into biogas, confirms the suitability of SAMBR for high suspended solids tannery wastewater. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. A Seasonally Robust Empirical Algorithm to Retrieve Suspended Sediment Concentrations in the Scheldt River

    Directory of Open Access Journals (Sweden)

    Dries Raymaekers


    Full Text Available A seasonally robust algorithm for the retrieval of Suspended Particulate Matter (SPM in the Scheldt River from hyperspectral images is presented. This algorithm can be applied without the need to simultaneously acquire samples (from vessels and pontoons. Especially in dynamic environments such as estuaries, this leads to a large reduction of costs, both in equipment and personnel. The algorithm was established empirically using in situ data of the water-leaving reflectance obtained over the tidal cycle during different seasons and different years. Different bands and band combinations were tested. Strong correlations were obtained for exponential relationships between band ratios and SPM concentration. The best performing relationships are validated using airborne hyperspectral data acquired in June 2005 and October 2007 at different moments in the tidal cycle. A band ratio algorithm (710 nm/596 nm was successfully applied to a hyperspectral AHS image of the Scheldt River to obtain an SPM concentration map.

  5. Computing time-series suspended-sediment concentrations and loads from in-stream turbidity-sensor and streamflow data (United States)

    Rasmussen, Patrick P.; Gray, John R.; Glysson, G. Doug; Ziegler, Andrew C.


    Over the last decade, use of a method for computing suspended-sediment concentration and loads using turbidity sensors—primarily nephelometry, but also optical backscatter—has proliferated. Because an in- itu turbidity sensor is capa le of measuring turbidity instantaneously, a turbidity time series can be recorded and related directly to time-varying suspended-sediment concentrations. Depending on the suspended-sediment characteristics of the measurement site, this method can be more reliable and, in many cases, a more accurate means for computing suspended-sediment concentrations and loads than traditional U.S. Geological Survey computational methods. Guidelines and procedures for estimating time s ries of suspended-sediment concentration and loading as a function of turbidity and streamflow data have been published in a U.S. Geological Survey Techniques and Methods Report, Book 3, Chapter C4. This paper is a summary of these guidelines and discusses some of the concepts, s atistical procedures, and techniques used to maintain a multiyear suspended sediment time series.

  6. Spatial variability of suspended sediment concentration within a tidal marsh in San Francisco Estuary (United States)

    Swanson, K.; Drexler, J. Z.; Schoellhamer, D. H.; Buffington, K.; Takekawa, J.


    The sustainability of existing marshes and feasibility of future marsh restoration projects in San Francisco Estuary and elsewhere are threatened by a potential imbalance between accelerating sea-level rise and tidal marsh accretion rates. Marsh accretion is, in large part, dependent upon the availability of suspended sediment supplied from adjacent waterways. As water and sediment move across a marsh plain, suspended sediment settles and is trapped by vegetation near the source, resulting in less suspended-sediment concentration (SSC) and deposition in the interior of the marsh. Measurements of deposition and limited observations of SSC within marshes have confirmed a decrease in sediment supply and accumulation from the marsh edge to the marsh interiors, but the spatial variability of SSC has not been quantified in a manner that allows for comparison to a theoretical sediment transport model. For this study, transects of SSC were collected within a marsh at China Camp State Park in the San Francisco Estuary which demonstrate that a dominant pattern of settling can be quantified and generally matches the exponentially decreasing pattern of SSC predicted by a simple advection-settling model. The observed pattern suggests that sediment settling and marsh flow characteristics are consistent both spatially (between transects) and temporally (between monthly sampling events). However, deviations from the predicted pattern occurred systematically at some locations and are likely related to resuspension of sediment from the marsh surface or small, unmapped creek channels that supply sediment to the marsh. Despite these deviations, our data show this simple 1-D model of advection and settling can be used to generalize within-marsh sediment transport as a function of distance from the nearest sediment source.


    Directory of Open Access Journals (Sweden)

    Ir kasam


    Full Text Available digunakan sebagai air minum. Adapun parameter yang cukup tinggi pada air permukaan adalah bakteri E. Coli dan Total Suspended Solid (TSS. Salah satu alternative pengolahan untuk parameter bakteri E. Coli dan TSS adalah dengan filtrasi dengan membran filter. Membran keramik adalah salah satu alat yang bisa digunakan sebagai filter pada air permukaan. Penelitian ini bertujuan untuk mengetahui kinerja membran keramik dalam menurunkan E.Coli dan TSS pada air permukan. Metode penelitian dilakukan dengan menggunakan membran keramik ukuran diameter 10 cm dan tinggi 20 cm yang terbuat dari tanah lempung, pasir kwarsa dan serbuk gergaji dengan komposisi 7,5% (membran 1 dan 10% (membran 2 bertujuan untuk membuat porositas dan pembakaran pada temperatur 900 – 1200 oC. Selanjutnya air permukaan dialirkan pada membran keramik secara kontinyu. Pengujian E.Coli dan TSS dilakukan pada menit ke 30, 60, 90, 120, 150, dan 180 dari waktu pengaliran. Dari hasil pengujian E. Coli dan TSS, diketahui bahwa membran keramik dapat menurunkan parameter E.Coli dan TSS pada air permukaan. E. Coli menurun hingga 98% untuk kedua membran 7,5% dan 10 % serbuk gergaji. Sedangkan TSS menurun hingga 72,55% pada membran keramik 7,5 % dan 65,22% pada membran 10%.

  8. Quantification and Analysis of Suspended Sediments Concentration Using Mobile and Static Acoustic Doppler Current Profiler Instruments

    Directory of Open Access Journals (Sweden)

    Angga Dwinovantyo


    Full Text Available The application of Acoustic Doppler Current Profiler (ADCP can be used not only for measuring ocean currents, but also for quantifying suspended sediment concentrations (SSC from acoustic backscatter strength based on sonar principle. Suspended sediment has long been recognized as the largest sources of sea contaminant and must be considered as one of the important parameters in water quality of seawater. This research was to determine SSC from measured acoustic backscattered intensity of static and mobile ADCP. In this study, vertically mounted 400 kHz and 750 kHz static ADCP were deployed in Lembeh Strait, North Sulawesi. A mobile ADCP 307.2 kHz was also mounted on the boat and moved to the predefined cross-section, accordingly. The linear regression analysis of echo intensity measured by ADCP and by direct measurement methods showed that ADCP is a reliable method to measure SSC with correlation coefficient (r 0.92. Higher SSC was observed in low water compared to that in high water and near port area compared to those in observed areas. All of this analysis showed that the combination of static and mobile ADCP methods produces reasonably good spatial and temporal data of SSC.

  9. Modeling of suspended sediment concentrations under combined wave-current flow over rippled bed (United States)

    Lu, Jing; Wang, Xiao Hua; Babanin, Alexander V.; Aijaz, Saima; Sun, Younjong; Teng, Yong; Jung, Kyung-Tae; Qiao, Fangli


    Ripples appear and disappear dynamically on coastal bed. The bottom stress can significantly be enhanced when ripples appear, and then the sediment transport will be influenced by the ripple-enhanced stress. However, ripples' impact on suspended sediments is seldom discussed. In this study, a bedform (ripples) module based on combined wave and current flow is coupled with a bottom boundary layer (BBL) model. This BBL model outputs our improved bottom shear stress (BSS) to both the sediment model (UNSW-sed) and the hydrodynamic model (POM). Model results in Jervis Bay of Australia show that the simulated suspended sediment concentration (SSC) of an abrupt rising is significantly improved by considering ripples rather than setting a uniform roughness (Kb) without ripples. However, the SSC is still underestimated by using previous schemes. Differently from the previous estimation of ripple-enhanced shear velocity U∗ cwe , noted as U∗ cwe _ NL , we introduce an U∗ cwe improved by calculating through ripple-enhanced ripple-enhanced Kb , which is noted as U∗ cwe _Kb . Simulation shows that U∗ cwe _Kb produces significantly increased SSC under high wave conditions, resulting in reasonable agreements with the measurements. The wave friction factor fw is shown to play a crucial role in causing the difference between U∗ cwe _Kb and U∗ cwe _ NL .

  10. An interlaboratory study as useful tool for proficiency testing of chemical oxygen demand measurements using solid substrates and liquid samples with high suspended solid content. (United States)

    Raposo, F; de la Rubia, M A; Borja, R; Alaiz, M; Beltrán, J; Cavinato, C; Clinckspoor, M; Demirer, G; Diamadopoulos, E; Helmreich, B; Jenicek, P; Martí, N; Méndez, R; Noguerol, J; Pereira, F; Picard, S; Torrijos, M


    In 2008, the first Proficiency Testing Scheme of Chemical Oxygen Demand (1(st)COD-PT(ADG)) was conducted to assess the results obtained for different research groups whose field work is mainly anaerobic digestion. This study was performed using four samples, two solid samples as raw materials and two solid samples to prepare high concentration suspended solid solutions. Invitations were sent to a large number of laboratories, mainly to anaerobic digestion research groups. Finally, thirty labs from sixteen countries agreed to participate, but for different reasons four participants could not send any data. In total, twenty-six results were reported to the COD-PT coordinator. This study showed the importance of continuous participation in proficiency testing (PT) schemes in order to compare the results obtained. Taking into account the lack of a general standard method and high quality certified reference materials (CRMs), the traceability of COD determination is not currently easy to check. In addition, the spread of participants' results obtained was high and pointed to the advisability of using consensus values due to their unreliability. Therefore, the theoretical oxygen demand (ThOD) values were considered as assigned values for all the samples analysed. On the other hand, in this PT the established standard deviation (ESD) has been determined by the Horwitz modified function. Participants of this 1(st)COD-PT(ADG) were asked to give a short report on the analytical method used. Although all the participants used potassium dichromate as their oxidant reagent, their experimental procedures were very different. With the purpose of comparing the results obtained, the different experimental conditions used were classified into five methods, corresponding to two main categories, open and closed reflux. The performance of laboratories was expressed by the z-score, whose value is considered satisfactory when z-score

  11. Dynamics of suspended sediment concentration, flow discharge and sediment particle size interdependency to identify sediment source (United States)

    Sadeghi, Seyed Hamidreza; Singh, Vijay P.


    Spatiotemporal behavior of sediment yield is a key for proper watershed management. This study analyzed statistical characteristics and trends of suspended sediment concentration (SCS), flow discharge (FD) and sediment particle sizes using data from 24 gage stations scattered throughout the United States. Analysis showed significant time- and location-specific differences of these variables. The median values of SSC, FD and percentage of particle sizes smaller than 63 μm (P63) for all 24 gage stations were found to be 510.236 mg l-1 (right skewed), 45.406 m3 s-1 (left skewed) and 78.648% (right skewed), respectively. Most of the stations exhibited significant trends (P management practices which may call for local or regional planning based on natural (i.e., precipitation amount, type and erosivity, watershed area, and soil erodibility) and human-affected (i.e., land use and hydraulic structures and water resources management) factors governing the study variables.

  12. Prediction and forecast of Suspended Sediment Concentration (SSC) on the Upper Yangtze basin (United States)

    Matos, José Pedro; Hassan, Marwan; Lu, Xixi; Franca, Mário J.


    Sediment transport in suspension may represent 90% or more of the global annual flux of sediment. For instance, more than 99% of the sediment supplied to the sea by the Yangtze River is suspended load. Suspended load is an important component for understanding channel dynamics and landscape evolution. Sediments transported in suspension are a major source of nutrients for aquatic organisms in riparian and floodplain habitats, and play a beneficial role acting as a sink in the carbon cycle. Excess of fine sediments may also have adverse effects. It can impair fish spawning by riverbed clogging, disturb foraging efficiency of hunting of river fauna, cause algae and benthos scouring, reduce or inhibit exchanges through the hyporheic region. Accumulation of fine sediments in reservoirs reduces storage capacity. Although fine sediment dynamics has been the focus of many studies, the current knowledge of sediment sources, transfer, and storage is inadequate to address fine sediment dynamics in the landscape. The theoretical derivation of a complete model for suspended sediment transport at the basin scale, incorporating small scale processes of production and transport, is hindered because the underlying mechanisms are produced at different non-similar scales. Availability of long-term reliable data on suspended sediment dynamics is essential to improve our knowledge on transport processes and to develop reliable sediment prediction models. Over the last 60 years, the Yangtze River Commission has been measuring the daily Suspended Sediment Concentration (SSC) at the Pingshan station. This dataset provides a unique opportunity to examine temporal variability and controls of fine sediment dynamics in the Upper Yangtze basin. The objective of this study is to describe temporal variation of fine sediment dynamics at the Pingshan station making use of the extensive sediment monitoring program undertaken at that location. We test several strategies of prediction and forecast

  13. An investigation into the effectiveness of sand media amended with biochar to remove BOD5, suspended solids and coliforms using wetland mesocosms. (United States)

    de Rozari, P; Greenway, M; El Hanandeh, A


    Constructed wetland ecotechnologies (CWEs) are a promising solution to effectively treat domestic wastewater in developing countries at low cost. This paper reports the findings of the effectiveness of sand media amended with woody biochar and two plants species (Melaleuca quinquenervia and Cymbopogon citratus) in removing biological oxygen demand (BOD5), suspended solids and coliforms. The experimental design consisted of 21 vertical flow (VF) mesocosms. There were seven media treatments using sand amended with varying proportions of biochar. During the first 8 months, the mesocosms were loaded with secondary clarified wastewater (SCW) then septage. The influent had a 4-day hydraulic retention time. Samples were monitored for BOD5, total suspended solids (TSS), total volatile solids (TVS), total coliforms and faecal coliforms. In the first 8 months, there were no significant performance differences between media treatments in the outflow concentrations of BOD5, TSS and TVS. The significant differences occurred during the last 3 months; using septage with biochar additions performed better than pure sand. For coliforms, the significant differences occurred after 6 months. In conclusion, the addition of biochar was not effective for SCW. The VF mesocosms system proved to be more effective in removing BOD5, TSS, TVS and coliforms when septage was loaded into the media.

  14. [Retrieving for chlorophyll-a concentration and suspended substance concentration based on HJ-1A HIS image]. (United States)

    Yang, Ting; Zhang, Hui; Wang, Qiao; Zhao, Qiao-Hua


    Based on geometry correction using ERDAS software and radiation correction using 6S model for HJ-1A hyper-spectrum image (HSI) on May 2 in 2010 and the analysis of spectrum for water data and spectral data of hyper-spectrum image, this paper processes original spectrum data of 28 sample points using method of normalization and method of first-order derivation. Single-band and band combination are selected to establish inversion models of the concentration of chlorophyll-a and solid suspensions. Choosing the model with biggest correlation coefficient, the spatial distribution map of the concentration of chlorophyll-a and solid suspensions content in Taihu Lake is acquired. The research results show: Band-73 of hyper-spectrum image which has been normalized shows the biggest correlation coefficient of the concentration of chlorophyll-a, remote sensing sediment parameter shows the biggest correlation coefficient of the concentration of solid suspensions, the result is consistent with analysis of spectral data of hyper-spectrum image. Average relative errors of predicted and measured values are within 30 percent. Spatial distribution map of water quality is consistent with the result of field surveys. Therefore, based on reference of the analysis of sensitive band of spectrum for water data, HJ-1A hyper-spectrum image can give quantitative estimation of water quality parameters in Taihu Lake.

  15. Effects of suspended sediment concentration and grain size on three optical turbidity sensors (United States)

    Merten, Gustavo Henrique; Capel, Paul D.; Minella, Jean P.G.


    Purpose: Optical turbidity sensors have been successfully used to determine suspended sediment flux in rivers, assuming the relation between the turbidity signal and suspended sediment concentration (SSC) has been appropriately calibrated. Sediment size, shape and colour affect turbidity and are important to incorporate into the calibration process. Materials and methods: This study evaluates the effect of SSC and particle size (i.e. medium sand, fine sand, very fine sand, and fines (silt + clay)) on the sensitivity of the turbidity signal. Three different turbidity sensors were used, with photo detectors positioned at 90 and 180 degrees relative to the axis of incident light. Five different sediment ratios of sand:fines (0:100, 25:75, 50:50, 75:25 and 100:0) were also evaluated for a single SSC (1000 mg l-1). Results and discussion: The photo detectors positioned at 90 degrees were more sensitive than sensor positioned at 180 degrees in reading a wide variety of grain size particles. On average for the three turbidity sensors, the sensitivity for fines were 170, 40, and 4 times greater than sensitivities for medium sand, fine sand, and very fine sand, respectively. For an SSC of 1000 mg l-1 with the treatments composed of different proportions of sand and fines, the presence of sand in the mixture linearly reduced the turbidity signal. Conclusions: The results indicate that calibration of the turbidity signal should be carried out in situ and that the attenuation of the turbidity signal due to sand can be corrected, as long as the proportion of sand in the SSC can be estimated.

  16. Determination of suspended particulate matter concentration from turbidity measurements: particle size effects and calibration procedures (United States)

    Pfannkuche, J.; Schmidt, A.


    Measurements of suspended particulate matter concentration and turbidity point towards the possibility of a site-specific algorithm (SPM), relating SPM to nephelometric turbidity units (NTU). In this paper regression models are presented that account for changes in the relationship of SPM and NTU as a result of changes in particle properties. The models have been developed by the use of daily measurements of SPM concentration and a continuous record of turbidity for the period from June 1996 to February 2001 in the River Elbe, a major river in the eastern part of Germany.The effect of changes in the particle properties with increasing water discharge was taken into account by varying the slope of a linear regression equation according to a logistic function. Water discharge, Q, was defined to be the only variable of this function - as an adequate substitute of the parameter bottom shear stress, which cannot be measured directly. Measurements of flow velocity in the River Elbe show that bottom shear stress is related almost linearly to water discharge up to bankful discharges.Regression models with slopes varying continuously with hydraulic parameters may account for the effects resulting from changes of particle characteristics and thus may have some advantages compared with models with a constant slope or models calibrated for different seasons.

  17. [Remote sensing inversion mode of suspended particles concentration in Hangzhou Bay based on in situ measurement spectrum]. (United States)

    Wang, Fan; Zhou, Bin; Xu, Jian-Ming; Ling, Zai-Ying


    Suspended particles are one of major parameters of coastal water color remote sensing in China. The reflectances spectral of water were measured using an ASD field spectroscope, synchronously the suspended particles concentrations of surface water were acquired in Hangzhou Bay. Two remote sensing inversion models for suspended particles concentrations (SPC) were developed based on t hesimulated reflectance of MODIS & MERIS channels using artificial neural network (ANN) algorithm. Measurement results show that the total SPC of Hangzhou bay is comparatively high where the suspended sediments concentrations (SSC) are far more than chlorophyll concentrations, averagely 705 mg/L and 1.164 mg/m3, reseparately. The SPC in two measurement stations appears spatio-temporal variation, especially the short period change due to tidal cycle. There are two reflectance peaks in the measured spectral curves, one is between 650 nm to 750 nm, and the other is near 800 nm. The first order derivative curves of reflectance spectral indicate that the first reflectance peaks shift to long wavelength according to the increased SSC. The ANN models make full use of the spectral information in different channels which can simulate the pigment and non-pigment particles concentrations at same time. The fitting effects are preferable with R2 more than 0.95 for each model. The ANN mode can be used for satellite remote sensing inversion, especially MERIS data, because of its comparatively high spatial resolution.

  18. Suspended Particulates Concentration (PM10 under Unstable Atmospheric Conditions over Subtropical Urban Area (Qena, Egypt

    Directory of Open Access Journals (Sweden)

    M. El-Nouby Adam


    Full Text Available The main purpose of this study is to evaluate the suspended particulates (PM10 in the atmosphere under unstable atmospheric conditions. The variation of PM10 was investigated and primary statistics were employed. The results show that, the PM10 concentrations values ranged from 6.00 to 646.74 μg m−3. The average value of PM10 is equal to 114.32 μg m−3. The high values were recorded in April and May (155.17 μg m−3 and 171.82 μg m−3, respectively and the low values were noted in February and December (73.86 μg m−3 and 74.05 μg m−3, respectively. The average value of PM10 of the hot season (125.35 × 10−6 g m−3 was higher than its value for the cold season (89.27 μg m−3. In addition, the effect of weather elements (air temperature, humidity and wind on the concentration of PM10 was determined. The multiple R between PM10 and these elements ranged from 0.05 to 0.47 and its value increased to reach 0.73 for the monthly average of the database used. Finally, the PM10 concentrations were grouped depending on their associated atmospheric stability class. These average values were equal to 122.80 ± 9 μg m−3 (highly unstable or convective, 109.37 ± 12 μg m−3 (moderately unstable and 104.42 ± 15 μg m−3 (slightly unstable.

  19. Estimation of suspended sediment flux in streams using continuous turbidity and flow data coupled with laboratory concentrations (United States)

    Jack Lewis


    The widening use of sediment surrogate measurements such as turbidity necessitates consideration of new methods for estimating sediment flux. Generally, existing methods can be simply be used in new ways. The effectiveness of a method varies according to the quality of the surrogate data and its relation to suspended sediment concentration (SSC). For this discussion,...

  20. Acoustic doppler velocimeter backscatter for quantification of suspended sediment concentration in South San Francisco Bay (United States)

    Ozturk, Mehmet; Work, Paul


    A data set was acquired on a shallow mudflat in south San Francisco Bay that featured simultaneous, co-located optical and acoustic sensors for subsequent estimation of suspended sediment concentrations (SSC). The optical turbidity sensor output was converted to SSC via an empirical relation derived at a nearby site using bottle sample estimates of SSC. The acoustic data was obtained using an acoustic Doppler velocimeter. Backscatter and noise were combined to develop another empirical relation between the optical estimates of SSC and the relative backscatter from the acoustic velocimeter. The optical and acoustic approaches both reproduced similar general trends in the data and have merit. Some seasonal variation in the dataset was evident, with the two methods differing by greater or lesser amounts depending on which portion of the record was examined. It is hypothesized that this is the result of flocculation, affecting the two signals by different degrees, and that the significance or mechanism of the flocculation has some seasonal variability. In the earlier portion of the record (March), there is a clear difference that appears in the acoustic approach between ebb and flood periods, and this is not evident later in the record (May). The acoustic method has promise but it appears that characteristics of flocs that form and break apart may need to be accounted for to improve the power of the method. This may also be true of the optical method: both methods involve assuming that the sediment characteristics (size, size distribution, and shape) are constant

  1. Acoustic Doppler velocimeter backscatter for quantification of suspended sediment concentration in South San Francisco Bay, USA (United States)

    Öztürk, Mehmet; Work, Paul


    A data set was acquired on a shallow mudflat in south San Francisco Bay that featured simultaneous, co-located optical and acoustic sensors for subsequent estimation of suspended sediment concentrations (SSC). The optical turbidity sensor output was converted to SSC via an empirical relation derived at a nearby site using bottle sample estimates of SSC. The acoustic data was obtained using an acoustic Doppler velocimeter. Backscatter and noise were combined to develop another empirical relation between the optical estimates of SSC and the relative backscatter from the acoustic velocimeter. The optical and acoustic approaches both reproduced similar general trends in the data and have merit. Some seasonal variation in the dataset was evident, with the two methods differing by greater or lesser amounts depending on which portion of the record was examined. It is hypothesized that this is the result of flocculation, affecting the two signals by different degrees, and that the significance or mechanism of the flocculation has some seasonal variability. In the earlier portion of the record (March), there is a clear difference that appears in the acoustic approach between ebb and flood periods, and this is not evident later in the record (May). The acoustic method has promise but it appears that characteristics of flocs that form and break apart may need to be accounted for to improve the power of the method. This may also be true of the optical method: both methods involve assuming that the sediment characteristics (size, size distribution, and shape) are constant.

  2. Parameterization of Time-Averaged Suspended Sediment Concentration in the Nearshore

    Directory of Open Access Journals (Sweden)

    Hyun-Doug Yoon


    Full Text Available To quantify the effect of wave breaking turbulence on sediment transport in the nearshore, the vertical distribution of time-averaged suspended sediment concentration (SSC in the surf zone was parameterized in terms of the turbulent kinetic energy (TKE at different cross-shore locations, including the bar crest, bar trough, and inner surf zone. Using data from a large-scale laboratory experiment, a simple relationship was developed between the time-averaged SSC and the time-averaged TKE. The vertical variation of the time-averaged SSC was fitted to an equation analogous to the turbulent dissipation rate term. At the bar crest, the proposed equation was slightly modified to incorporate the effect of near-bed sediment processes and yielded reasonable agreement. This parameterization yielded the best agreement at the bar trough, with a coefficient of determination R2 ≥ 0.72 above the bottom boundary layer. The time-averaged SSC in the inner surf zone showed good agreement near the bed but poor agreement near the water surface, suggesting that there is a different sedimentation mechanism that controls the SSC in the inner surf zone.

  3. Remote sensing and water quality indicators in the Korean West coast: Spatio-temporal structures of MODIS-derived chlorophyll-a and total suspended solids. (United States)

    Kim, Hae-Cheol; Son, Seunghyun; Kim, Yong Hoon; Khim, Jong Seong; Nam, Jungho; Chang, Won Keun; Lee, Jung-Ho; Lee, Chang-Hee; Ryu, Jongseong


    The Yellow Sea is a shallow marginal sea with a large tidal range. In this study, ten areas located along the western coast of the Korean Peninsula are investigated with respect to remotely sensed water quality indicators derived from NASA MODIS aboard of the satellite Aqua. We found that there was a strong seasonal trend with spatial heterogeneity. In specific, a strong six-month phase-lag was found between chlorophyll-a and total suspended solid owing to their inversed seasonality, which could be explained by different dynamics and environmental settings. Chlorophyll-a concentration seemed to be dominantly influenced by temperature, while total suspended solid was largely governed by local tidal forcing and bottom topography. This study demonstrated the potential and applicability of satellite products in coastal management, and highlighted find that remote-sensing would be a promising tool in resolving orthogonality of large spatio-temporal scale variabilities when combining with proper time series analyses. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. The influence of air-suspended particulate concentration on the incidence of suicide attempts and exacerbation of schizophrenia (United States)

    Yackerson, Naomy S.; Zilberman, Arkadi; Todder, Doron; Kaplan, Zeev


    The main objective of this study was to evaluate the role of the concentration of solid air-suspended particles (SSP) in the incidence of mental disorders. The study is based on 1,871 cases, registered in the Beer-Sheva Mental Health Center (BS-MHC) at Ben-Gurion University (Israel) during a 16-month period from 2001 to 2002; 1,445 persons were hospitalized due to exacerbation of schizophrenia (ICD-10: F20-F29) and 426 after committing a suicide attempt using a variety of means as coded in the ICD-10 (ICD-10: X60-X84). Pearson and Spearman test correlations were used; the statistical significance was tested at p 0.3, p 0.2). A trend towards positive correlation ( ρ > 0.2, p psychotic attack ( N PS ) in periods with dominant eastern winds (4-9 am, local time) has been observed, while in the afternoon and evening hours (1-8 pm local time) with dominant western winds, N C and N PS are not correlated (p > 0.1). Obviously, concentration of SSP is not the one and only parameter of air pollution state determining meteorological-biological impact, involving incidence of mental disorders, although its role can scarcely be overstated. However, since it is one of the simplest measured parameters, it could be widely used and helpful in the daily struggle for human life comfort in semi-arid areas as well as urban and industrial surroundings, where air pollution reaches crucial values. This study may permit determination of the limits for different external factors, which do not overcome threshold values (without provoking avalanche situations), to single out the group of people at increased risk (with according degree of statistic probability), whose reactions to the weather violations can involve the outbreak of frustration points and prevent or alleviate detrimental mental effects.

  5. Prediction of suspended-sediment concentrations at selected sites in the Fountain Creek watershed, Colorado, 2008-09 (United States)

    Stogner, Sr., Robert W.; Nelson, Jonathan M.; McDonald, Richard R.; Kinzel, Paul J.; Mau, David P.


    In 2008, the U.S. Geological Survey (USGS), in cooperation with Pikes Peak Area Council of Governments, Colorado Water Conservation Board, Colorado Springs City Engineering, and the Lower Arkansas Valley Water Conservancy District, began a small-scale pilot study to evaluate the effectiveness of the use of a computational model of streamflow and suspended-sediment transport for predicting suspended-sediment concentrations and loads in the Fountain Creek watershed in Colorado. Increased erosion and sedimentation damage have been identified by the Fountain Creek Watershed Plan as key problems within the watershed. A recommendation in the Fountain Creek Watershed plan for management of the basin is to establish measurable criteria to determine if progress in reducing erosion and sedimentation damage is being made. The major objective of this study was to test a computational method to predict local suspended-sediment loads at two sites with different geomorphic characteristics in order to evaluate the feasibility of using such an approach to predict local suspended-sediment loads throughout the entire watershed. Detailed topographic surveys, particle-size data, and suspended-sediment samples were collected at two gaged sites: Monument Creek above Woodmen Road at Colorado Springs, Colorado (USGS gage 07103970), and Sand Creek above mouth at Colorado Springs, Colorado (USGS gage 07105600). These data were used to construct three-dimensional computational models of relatively short channel reaches at each site. The streamflow component of these models predicted a spatially distributed field of water-surface elevation, water velocity, and bed shear stress for a range of stream discharges. Using the model predictions, along with measured particle sizes, the sediment-transport component of the model predicted the suspended-sediment concentration throughout the reach of interest. These computed concentrations were used with predicted flow patterns and channel morphology to

  6. Report of meeting on measurement of suspended solids in the Meuse

    NARCIS (Netherlands)

    Joziasse, J.; Klaver, G.; Bakker, I.


    On June 19/20, 2007 a visit was paid to a suspended particulate matter (SPM) sampling and monitoring site in the Ourthe river (Liège region), between the confluence with the Vesdre river and the mouth of the Ourthe in the Meuse river. The next day, a workshop was organised in which backgrounds,

  7. Comparison of Suspended Solids and Turbidity Estimates from MODIS and MERIS Images in the Three Gorges Dam Area (United States)

    Di Trapani, Antonio; Corbari, Chiara; Mancini, Marco


    The aim of this work is to evaluate turbidity and total suspended matter (TSM) along the Yangtze river and the Three Gorges Reservoir, China, applying different retrieval algorithms to satellite imagery (MOD09GQ and MERIS FRS L2). Turbidity and TSM are then correlated to ground daily discharges, showing good correlations. Daily estimates of TSM are then obtained even for the days for which satellite scenes are not available, applying the obtained relations between ground discharge and satellite estimates of TSM. Daily satellite TSM are compared with literature values of solid discharge measurements.

  8. The effect of source suspended sediment concentration on the sediment dynamics of a macrotidal creek and salt marsh (United States)

    Poirier, Emma; van Proosdij, Danika; Milligan, Timothy G.


    Seasonal variability in the sediment dynamics of a Bay of Fundy tidal creek and salt marsh system was analyzed to better understand the ecomorphodynamics of a high suspended sediment concentration intertidal habitat. Data were collected over 62 tides for velocity, suspended sediment concentration, deposition, and grain size at four stations from the creek thalweg to the marsh surface. Five topographic surveys were also conducted throughout the 14-month study. Deposition rates per tide varied spatially from 56.4 g m-2 at the creek thalweg to 15.3 g m-2 at the marsh surface. Seasonal variations in deposition in the creek and marsh surface were from 38.0 g m-2 to 97.7 g m-2 and from 12.2 g m-2 to 19.6 g m-2 respectively. Deposition and erosion were greatest in late fall and winter. This seasonal change, led by higher suspended sediment concentrations, was observed in the creek and at the marsh bank but notably absent from the marsh edge and marsh surface. Sediments were predominantly deposited in floc form (76-83%). Because of high floc content, higher suspended sediment concentrations led to more rapid loss of sediment from suspension. With increasing sediment concentration, deposition increased in the tidal creek and at the marsh bank but not at the marsh edge or marsh surface. This suggests that in highly flocculated environments the water column clears fast enough that very little sediment remains in suspension when the water reaches the marsh and that the sediment concentration during marsh inundation is independent of the initial concentration in the creek.

  9. Remote Sensing Analysis of Temperature and Suspended Sediment Concentration in Ayeyarwady River in Myanmar (United States)

    Thanda Ko, Nyein; Rutten, Martine


    Detailed spatial coverage of water quality parameters are crucial to better manage rivers. However, collection of water quality parameters is both time consuming and costly for large rivers. This study demonstrates that Operational Land Image (OLI) Sensor on board of Landsat 8 can be successfully applied for the detection of spatial patterns of water temperature as well as suspended sediment concentration (SSC) using the Ayeyarwady river, Myanmar as a case study. Water temperature estimation was obtained from the brightness thermal Band 10 by using the Split-Window algorithm. The study finds that there is a close agreement between the remote sensing temperature and in-situ temperature with relative error in the range from 4.5% to 8.2%. The sediment load of Ayeyarwady river is ranked as the third-largest sediment load among the world's rivers but there is very little known about this important parameter, due to a lack of adequate gauge data. The single band reflectance of Landsat image (Band 5) seems a good indicator for the estimation of SSC with relative error in the range of less than 10% but the developed empirical formula by the power relation with the only seven ground reference points is uncertain to apply for the entire river basin. It is to note that an important constraint for the sediment analysis is the availability of spatial and temporal ground reference data. Future studies should also focus on the improvement of ground reference data points to become more reliable, because most of the river in Asia, especially in Myanmar, don't have readily available continuous ground sediment data points due to lack of measurement gauge stations through the river.

  10. Improving suspended sediment measurements by automatic samplers. (United States)

    Gettel, Melissa; Gulliver, John S; Kayhanian, Masoud; DeGroot, Gregory; Brand, Joshua; Mohseni, Omid; Erickson, Andrew J


    Suspended solids either as total suspended solids (TSS) or suspended sediment concentration (SSC) is an integral particulate water quality parameter that is important in assessing particle-bound contaminants. At present, nearly all stormwater runoff quality monitoring is performed with automatic samplers in which the sampling intake is typically installed at the bottom of a storm sewer or channel. This method of sampling often results in a less accurate measurement of suspended sediment and associated pollutants due to the vertical variation in particle concentration caused by particle settling. In this study, the inaccuracies associated with sampling by conventional intakes for automatic samplers have been verified by testing with known suspended sediment concentrations and known particle sizes ranging from approximately 20 μm to 355 μm under various flow rates. Experimental results show that, for samples collected at a typical automatic sampler intake position, the ratio of sampled to feed suspended sediment concentration is up to 6600% without an intake strainer and up to 300% with a strainer. When the sampling intake is modified with multiple sampling tubes and fitted with a wing to provide lift (winged arm sampler intake), the accuracy of sampling improves substantially. With this modification, the differences between sampled and feed suspended sediment concentration were more consistent and the sampled to feed concentration ratio was accurate to within 10% for particle sizes up to 250 μm.

  11. Hydrology, phosphorus, and suspended solids in five agricultural streams in the Lower Fox River and Green Bay Watersheds, Wisconsin, Water Years 2004-06 (United States)

    Graczyk, David J.; Robertson, Dale M.; Baumgart, Paul D.; Fermanich, Kevin J.


    A 3-year study was conducted by the U.S. Geological Survey and the University of Wisconsin-Green Bay to characterize water quality in agricultural streams in the Fox/Wolf watershed in northeastern Wisconsin and provide information to assist in the calibration of a watershed model for the area. Streamflow, phosphorus, and suspended solids data were collected between October 1, 2003, and September 30, 2006, in five streams, including Apple Creek, Ashwaubenon Creek, Baird Creek, Duck Creek, and the East River. During this study, total annual precipitation was close to the 30-year normal of 29.12 inches. The 3-year mean streamflow was highest in the East River (113 ft3/s), followed by Duck Creek (58.2 ft3/s), Apple Creek (26.9 ft3/s), Baird Creek (12.8 ft3/s), and Ashwaubenon Creek (9.1 ft3/s). On a yield basis, during these three years, the East River had the highest flow (0.78 ft3/s/mi2), followed by Baird Creek (0.61 ft3/s/mi2), Apple Creek (0.59 ft3/s/mi2), Duck Creek (0.54 ft3/s/mi2), and Ashwaubenon Creek (0.46 ft3/s/mi2). The overall median total suspended solids (TSS) concentration was highest in Baird Creek (73.5 mg/L), followed by Apple and Ashwaubenon Creeks (65 mg/L), East River (40 mg/L), and Duck Creek (30 mg/L). The median total phosphorus (TP) concentration was highest in Ashwaubenon Creek (0.60 mg/L), followed by Baird Creek (0.47 mg/L), Apple Creek (0.37 mg/L), East River (0.26 mg/L), and Duck Creek (0.22 mg/L).

  12. Chemical concentrations in water and suspended sediment, Green River to Lower Duwamish Waterway near Seattle, Washington, 2016–17 (United States)

    Conn, Kathleen E.; Black, Robert W.; Peterson, Norman T.; Senter, Craig A.; Chapman, Elena A.


    From August 2016 to March 2017, the U.S. Geological Survey (USGS) collected representative samples of filtered and unfiltered water and suspended sediment (including the colloidal fraction) at USGS streamgage 12113390 (Duwamish River at Golf Course, at Tukwila, Washington) during 13 periods of differing flow conditions. Samples were analyzed by Washington-State-accredited laboratories for a large suite of compounds, including metals, dioxins/furans, semivolatile compounds including polycyclic aromatic hydrocarbons, butyltins, the 209 polychlorinated biphenyl (PCB) congeners, and total and dissolved organic carbon. Concurrent with the chemistry sampling, water-quality field parameters were measured, and representative water samples were collected and analyzed for river suspended-sediment concentration and particle-size distribution. The results provide new data that can be used to estimate sediment and chemical loads transported by the Green River to the Lower Duwamish Waterway.

  13. Factors Impeding Enzymatic Wheat Gluten Hydrolysis at High Solid Concentrations

    NARCIS (Netherlands)

    Hardt, N.A.; Janssen, A.E.M.; Boom, R.M.; Goot, van der A.J.


    Enzymatic wheat gluten hydrolysis at high solid concentrations is advantageous from an environmental and economic point of view. However, increased wheat gluten concentrations result in a concentration effect with a decreased hydrolysis rate at constant enzyme-to-substrate ratios and a decreased

  14. Response of reef corals on a fringing reef flat to elevated suspended-sediment concentrations: Moloka‘i, Hawai‘i (United States)

    Jokiel, Paul L.; Rodgers, Ku'ulei S.; Storlazzi, Curt D.; Field, Michael E.; Lager, Claire V.; Lager, Dan


    A long-term (10 month exposure) experiment on effects of suspended sediment on the mortality, growth, and recruitment of the reef corals Montipora capitata and Porites compressa was conducted on the shallow reef flat off south Molokaʻi, Hawaiʻi. Corals were grown on wire platforms with attached coral recruitment tiles along a suspended solid concentration (SSC) gradient that ranged from 37 mg l−1 (inshore) to 3 mg l−1(offshore). Natural coral reef development on the reef flat is limited to areas with SSCs less than 10 mg l−1 as previously suggested in the scientific literature. However, the experimental corals held at much higher levels of turbidity showed surprisingly good survivorship and growth. High SSCs encountered on the reef flat reduced coral recruitment by one to three orders of magnitude compared to other sites throughout Hawaiʻi. There was a significant correlation between the biomass of macroalgae attached to the wire growth platforms at the end of the experiment and percentage of the corals showing mortality. We conclude that lack of suitable hard substrate, macroalgal competition, and blockage of recruitment on available substratum are major factors accounting for the low natural coral coverage in areas of high turbidity. The direct impact of high turbidity on growth and mortality is of lesser importance.

  15. Concentrations, loads, and yields of total phosphorus, total nitrogen, and suspended sediment and bacteria concentrations in the Wister Lake Basin, Oklahoma and Arkansas, 2011-13 (United States)

    Buck, Stephanie D.


    The Poteau Valley Improvement Authority uses Wister Lake in southeastern Oklahoma as a public water supply. Total phosphorus, total nitrogen, and suspended sediments from agricultural runoff and discharges from wastewater treatment plants and other sources have degraded water quality in the lake. As lake-water quality has degraded, water-treatment cost, chemical usage, and sludge production have increased for the Poteau Valley Improvement Authority. The U.S. Geological Survey (USGS), in cooperation with the Poteau Valley Improvement Authority, investigated and summarized concentrations of total phosphorus, total nitrogen, suspended sediment, and bacteria (Escherichia coli and Enterococcus sp.) in surface water flowing to Wister Lake. Estimates of total phosphorus, total nitrogen, and suspended sediment loads, yields, and flow-weighted mean concentrations of total phosphorus and total nitrogen concentrations were made for the Wister Lake Basin for a 3-year period from October 2010 through September 2013. Data from water samples collected at fixed time increments during base-flow conditions and during runoff conditions at the Poteau River at Loving, Okla. (USGS station 07247015), the Poteau River near Heavener, Okla. (USGS station 07247350), and the Fourche Maline near Leflore, Okla. (USGS station 07247650), water-quality stations were used to evaluate water quality over the range of streamflows in the basin. These data also were collected to estimate annual constituent loads and yields by using regression models. At the Poteau River stations, total phosphorus, total nitrogen, and suspended sediment concentrations in surface-water samples were significantly larger in samples collected during runoff conditions than in samples collected during base-flow conditions. At the Fourche Maline station, in contrast, concentrations of these constituents in water samples collected during runoff conditions were not significantly larger than concentrations during base

  16. Response of suspended sediment concentration to tidal dynamics at a site inside the mouth of an inlet: Jiaozhou Bay (China

    Directory of Open Access Journals (Sweden)

    S. L. Yang


    Full Text Available Observations of fair weather currents and suspended sediment concentrations (SSC were made using an acoustic Doppler current profiler and two YSI turbidity sensors over a neap to spring time cycle at a site near the inner mouth of a semi-enclosed mesotidal-macrotidal embayment (Jiaozhou Bay to examine the influence of tidal dynamics on concentration and transport of suspended sediment. During the investigation, SSC varied from about 3 to 16 mg L–1 at the surface and about 6 to 40 mg L–1 close to the bed, while the current velocity reached 79 cm s–1 at the surface and 61 cm s–1 near the bed. SSC was tidally cyclic. The near-bed instantaneous SSC was closely related to current velocity with almost no time lag, indicating that the variability of SSC was governed by current-induced settling/resuspension. At the surface, however, instantaneous SSC was poorly related to instantaneous current velocity because the peak SSC tended to occur around ebb slack water. This suggests that the surface SSC was controlled by horizontal advection from landward higher concentration areas. Both at the surface and near the bed, on the other hand, tidally-averaged SSC was well correlated to tidal range and current speed. Current velocity and SSC were flood-dominated for all the tides investigated, which resulted in significant landward residual suspended sediment transport at the study site. The observed flood dominance was mainly attributed to the location of the study site on the landward side of the bay’s inlet where flow separation is favoured during flood tide. It was concluded that tides are the dominant hydrodynamic component controlling the variability of SSC during fair weather at the study area. Keywords: sediment, concentration, suspension, advection, currents, shoalling effect, Jiaozhou Bay, China

  17. Using multi-frequency acoustic attenuation to monitor grain size and concentration of suspended sediment in rivers. (United States)

    Moore, S A; Le Coz, J; Hurther, D; Paquier, A


    Multi-frequency acoustic backscatter profiles recorded with side-looking acoustic Doppler current profilers are used to monitor the concentration and size of sedimentary particles suspended in fluvial environments. Data at 300, 600, and 1200 kHz are presented from the Isère River in France where the dominant particles in suspension are silt and clay sizes. The contribution of suspended sediment to the through-water attenuation was determined for three high concentration (> 100 mg/L) events and compared to theoretical values for spherical particles having size distributions that were measured by laser diffraction in water samples. Agreement was good for the 300 kHz data, but it worsened with increasing frequency. A method for the determination of grain size using multi-frequency attenuation data is presented considering models for spherical and oblate spheroidal particles. When the resulting size estimates are used to convert sediment attenuation to concentration, the spheroidal model provides the best agreement with optical estimates of concentration, but the aspect ratio and grain size that provide the best fit differ between events. The acoustic estimates of size were one-third the values from laser grain sizing. This agreement is encouraging considering optical and acoustical instruments measure different parameters.

  18. Saturation Concentrations of Suspended Fine Sediment : Computations with the Prandtl Mixing-Length Model

    NARCIS (Netherlands)

    Kranenburg, C.


    Adopting a 1DV numerical model including the standard k-eps turbulence model, Winterwerp et al. (1999) calculated a saturation concentration for an initially uniform distribution of fine sediment concentration in steady flow. At concentrations exceeding the saturation concentration the concentration

  19. Guidelines and Procedures for Computing Time-Series Suspended-Sediment Concentrations and Loads from In-Stream Turbidity-Sensor and Streamflow Data (United States)

    Rasmussen, Patrick P.; Gray, John R.; Glysson, G. Douglas; Ziegler, Andrew C.


    In-stream continuous turbidity and streamflow data, calibrated with measured suspended-sediment concentration data, can be used to compute a time series of suspended-sediment concentration and load at a stream site. Development of a simple linear (ordinary least squares) regression model for computing suspended-sediment concentrations from instantaneous turbidity data is the first step in the computation process. If the model standard percentage error (MSPE) of the simple linear regression model meets a minimum criterion, this model should be used to compute a time series of suspended-sediment concentrations. Otherwise, a multiple linear regression model using paired instantaneous turbidity and streamflow data is developed and compared to the simple regression model. If the inclusion of the streamflow variable proves to be statistically significant and the uncertainty associated with the multiple regression model results in an improvement over that for the simple linear model, the turbidity-streamflow multiple linear regression model should be used to compute a suspended-sediment concentration time series. The computed concentration time series is subsequently used with its paired streamflow time series to compute suspended-sediment loads by standard U.S. Geological Survey techniques. Once an acceptable regression model is developed, it can be used to compute suspended-sediment concentration beyond the period of record used in model development with proper ongoing collection and analysis of calibration samples. Regression models to compute suspended-sediment concentrations are generally site specific and should never be considered static, but they represent a set period in a continually dynamic system in which additional data will help verify any change in sediment load, type, and source.

  20. An isolation-enhanced quad-element antenna using suspended solid wires for LTE small-cell base stations (United States)

    Chen, Yen-Sheng; Zhou, Huang-Cheng


    This paper presents a multiple-input-multiple-output (MIMO) antenna that has four-unit elements enabled by an isolation technique for long-term evolution (LTE) small-cell base stations. While earlier studies on MIMO base-station antennas cope with either a lower LTE band (698-960 MHz) or an upper LTE band (1710-2690 MHz), the proposed antenna meets the full LTE specification, yet it uses the maximum number of unit elements to increase channel capacity. The antenna configuration is optimized for good impedance matching and high radiation efficiency. In particular, as the spacing between unit elements is so small that severe mutual coupling occurs, we propose a simple structure with extremely low costs to enhance the isolation. By using suspended solid wires interconnecting the position having strong coupled current of two adjacent elements, an isolation enhancement of 37 dB is achieved. Although solid wires inherently aim at direct-current applications, this work successfully employs such a low-cost technique to microwave antenna development. Experimental results have validated the design guidelines and the proposed configuration, showing that antenna performances including impedance matching, isolation, radiation features, signal correlation, and channel capacity gain are highly desired for LTE small-cell base stations.

  1. Coagulation-Sedimentation-Extraction Pretreatment Methods for The Removal of Suspended Solids and Residual Oil From Palm Oil Mill Effluent (Pome

    Directory of Open Access Journals (Sweden)

    Abdul Latif Ahmad, Norliza Ibrahim , Suzylawati Ismail and Subhash Bhatia


    Full Text Available Suspended solids and residual oil removal in a liquid are relevant to numerous research areas and industry. The suspended solid cannot be removed completely by plain settling. Large and heavy particles can settle out readily, but smaller and lighter particles settle very slowly or in some cases do not settle at all. Because of this, it requires efficient physical-chemical pretreatment methods.   Our current research is to study the pretreatment methods in the removal of suspended solids and residual oil content in POME. Preliminary analysis shows that POME contains 40,000 mg/L suspended solid and 4,000 mg/L oil and grease content that relatively very high compared to the maximum allowable limit by the Malaysian Department of Environment which are only 400 mg/L and 50 mg/L respectively. The methods chosen were coagulation-sedimentation method for suspended solids removal and solvent extraction for residual oil removal.  Jar test apparatus was used as the standard procedure for bench-scale testing and alum was used as the coagulant. Parameters studied were alum dosage, mixing time, mixing speed, sedimentation time and pH. For removal of residual oil, six different organic solvents; n-hexane, n-heptane, benzene, petroleum ether, pentane and petroleum benzene were used. For every solvent the effect of solvent ratio, mixing time, mixing speed and pH were analyzed. The results show that the optimum conditions in removal of suspended solid from POME were at pH 4.11, sedimentation time of 100 minutes and 150 rpm mixing speed with 1.5 hr mixing time. N-hexane give the best performance in extracting residual oil from POME with solvent to POME ratio of 6:10. It was estimated about 0.54 grams of oil and grease can be extracted with optimum variables at pH 4, mixing speed of 200 rpm, and 20 minutes mixing time.  Key Words: palm oil mill effluent, coagulation, suspended solid, residual oil, solvent extraction.

  2. Particulate flux calculation based on metal contents and suspended sediment concentrations relationship: case study of turbid alpine river (Isere, France) (United States)

    Dutordoir, Solene; Nemery, Julien; Guedron, Stéphane; Arnaud, Jérémy; Minaudo, Camille; Belleudy, Philippe; Landas-Maneval, Jacqueline; Rivière, Carlos


    In the context of increasing stress on aquatic environment, the improvement of pollutant flux quantification in large rivers presents a strong stake. Isere at Grenoble city (5570 km2) is an alpine river in the Northern French Alps with high suspended sediment transport reaching 10 to 20 g L-1 during floods. It is known that for elements like P, Ni, Mn, Cr, Pb, Fe et Al, most of river transport is done under particulate forms. Isere River is susceptible to transport particulate pollutants such as metals, given mining history and industrial activities at the upstream watershed. Moreover, this river receives Grenoble city's effluents (500 000 inhabitants) and stormwaters during rain events. Three metals (Hg, Ni, Pb) identified as priority substances regarding European Water Framework Directive and As known to be one of the most metal of concern were chosen in this study. High frequency samplings of suspended sediments were realized between 2011 and 2012 in order to evaluate the temporal variation of metals contents and to determine geochemical background during high flow periods. In the same sampling site (situated upstream urban effluents of Grenoble city), discharge and suspended sediment concentration by turbidity were measured at 30 min frequency by a monitoring station. The use of historical and new databases ranging between low and high discharge (10 years return flood) allowed determining relationships between metal contents and suspended sediment concentrations and discharges. Results show a good correlation for the studied metals and permit to defined the geochemical backgrounds for each metals measured above 0.5 g L-1, (Hg = 68 +/- 48 ng g-1, Ni = 30 +/- 10 mg g-1, Pb = 43 +/-13 mg g-1, As = 15 +/- 4 mg g-1). These models were validated on a separated period than the one used for the calibration and applied to calculate particulate metals concentrations and associated incertitude at 30 min frequency using SSC and discharge database. Cumulative 30 minutes

  3. Pyrosequencing Reveals Bacterial Communities in Unchlorinated Drinking Water Distribution System: An Integral Study of Bulk Water, Suspended Solids, Loose Deposits, and Pipe Wall Biofilm

    KAUST Repository

    Liu, G.


    The current understanding of drinking water distribution system (DWDS) microbiology is limited to pipe wall biofilm and bulk water; the contributions of particle-associated bacteria (from suspended solids and loose deposits) have long been neglected. Analyzing the composition and correlation of bacterial communities from different phases helped us to locate where most of the bacteria are and understand the interactions among these phases. In the present study, the bacteria from four critical phases of an unchlorinated DWDS, including bulk water, pipe wall biofilm, suspended solids, and loose deposits, were quantified and identified by adenosine triphosphate analysis and pyrosequencing, respectively. The results showed that the bulk water bacteria (including the contribution of suspended solids) contributed less than 2% of the total bacteria. The bacteria associated with loose deposits and pipe wall biofilm that accumulated in the DWDS accounted for over 98% of the total bacteria, and the contributions of bacteria in loose deposits and pipe wall biofilm were comparable. Depending on the amount of loose deposits, its contribution can be 7-fold higher than the pipe wall biofilm. Pyrosequencing revealed relatively stable bacterial communities in bulk water, pipe wall biofilm, and suspended solids throughout the distribution system; however, the communities present in loose deposits were dependent on the amount of loose deposits locally. Bacteria within the phases of suspended solids, loose deposits, and pipe wall biofilm were similar in phylogenetic composition. The bulk water bacteria (dominated by Polaromonas spp.) were clearly different from the bacteria from the other three phases (dominated by Sphingomonas spp.). This study highlighted that the integral DWDS ecology should include contributions from all of the four phases, especially the bacteria harbored by loose deposits. The accumulation of loose deposits and the aging process create variable microenvironments

  4. Pyrosequencing reveals bacterial communities in unchlorinated drinking water distribution system: an integral study of bulk water, suspended solids, loose deposits, and pipe wall biofilm. (United States)

    Liu, G; Bakker, G L; Li, S; Vreeburg, J H G; Verberk, J Q J C; Medema, G J; Liu, W T; Van Dijk, J C


    The current understanding of drinking water distribution system (DWDS) microbiology is limited to pipe wall biofilm and bulk water; the contributions of particle-associated bacteria (from suspended solids and loose deposits) have long been neglected. Analyzing the composition and correlation of bacterial communities from different phases helped us to locate where most of the bacteria are and understand the interactions among these phases. In the present study, the bacteria from four critical phases of an unchlorinated DWDS, including bulk water, pipe wall biofilm, suspended solids, and loose deposits, were quantified and identified by adenosine triphosphate analysis and pyrosequencing, respectively. The results showed that the bulk water bacteria (including the contribution of suspended solids) contributed less than 2% of the total bacteria. The bacteria associated with loose deposits and pipe wall biofilm that accumulated in the DWDS accounted for over 98% of the total bacteria, and the contributions of bacteria in loose deposits and pipe wall biofilm were comparable. Depending on the amount of loose deposits, its contribution can be 7-fold higher than the pipe wall biofilm. Pyrosequencing revealed relatively stable bacterial communities in bulk water, pipe wall biofilm, and suspended solids throughout the distribution system; however, the communities present in loose deposits were dependent on the amount of loose deposits locally. Bacteria within the phases of suspended solids, loose deposits, and pipe wall biofilm were similar in phylogenetic composition. The bulk water bacteria (dominated by Polaromonas spp.) were clearly different from the bacteria from the other three phases (dominated by Sphingomonas spp.). This study highlighted that the integral DWDS ecology should include contributions from all of the four phases, especially the bacteria harbored by loose deposits. The accumulation of loose deposits and the aging process create variable microenvironments

  5. Estimation of total suspended matter concentration from MODIS data using a neural network model in the China eastern coastal zone (United States)

    Chen, Jun; Quan, Wenting; Cui, Tingwei; Song, Qingjun


    The objectives of this study are to evaluate the applicability of three existing retrieval models of total suspended matter (TSM) in the Bohai, Yellow, and East China Seas (BYES), and to propose a multilayer back propagation neural network (MBPNN) model. Based on the comparison of TSM predicted by these models with in situ measurements taken in the BYES, it was found that the MBPNN model produces a superior performance to the three existing models selected. Near-infrared band-based and shortwave infrared band-based combined model was used to remove the atmospheric effects from the moderate resolution imaging spectroradiometer (MODIS) data, and the TSM concentration was quantified from the MODIS data after atmospheric correction using the MBPNN model. It was found that the MBPNN model produces 41.4% uncertainty in deriving TSM concentration from the MODIS data. The MBPNN model-based climatological seasonal mean TSM concentration indicated that the highest TSM concentrations were found around the river estuaries, while the lowest values were found in the far offshore regions of the BYES. The MBPNN model-based monthly mean TSM concentration revealed that the highest TSM concentrations occurred in February, and the lowest in July. The diffuse attenuation coefficient at 490 nm (Kd(490)) depended heavily on TSM concentration in the BYES. The significant relationship (R2 = 0.72, p TSM concentration indicated that the BYES waters are TSM dominated types.

  6. Estimation of suspended sediment concentration from Acoustic Doppler Current Profiler (ADCP) instrument: A case study of Lembeh Strait, North Sulawesi (United States)

    Dwinovantyo, Angga; Manik, Henry M.; Prartono, Tri; Susilohadi; Ilahude, Delyuzar


    Measurement of suspended sediment concentration (SSC) is one of the parameters needed to determine the characteristics of sediment transport. However, the measurement of SSC nowadays still uses conventional technique and it has limitations; especially in temporal resolution. With advanced technology, the measurement can use hydroacoustic technology such as Acoustic Doppler Current Profiler (ADCP). ADCP measures the intensity of backscatter as echo intensity unit from sediment particles. The frequency of ADCP used in this study was 400 kHz. The samples were measured and collected from Lembeh Strait, North Sulawesi. The highest concentration of suspended sediment was 98.89 mg L-1 and the lowest was 45.20 mg L-1. Time series data showed the tidal condition affected the SSC. From the research, we also made correction from sound signal losses effect such as spherical spreading and sound absorption to get more accurate results by eliminating these parameters in echo intensity data. Simple linear regression analysis at echo intensity measured from ADCP to direct measurement of SSC was performed to obtain the estimation of the SSC. The comparison result of estimation of SSC from ADCP measurements and SSC from laboratory analyses was insignificantly different based on t-test statistical analysis with 95% confidence interval percentage.

  7. In situ densimetric measurements as a surrogate for suspended-sediment concentrations in the Rio Puerco, New Mexico (United States)

    Brown, Jeb E.; Gray, John R.; Hornewer, Nancy J.


    Surrogate measurements of suspended-sediment concentration (SSC) are increasingly used to provide continuous, high-resolution, and demonstrably accurate data at a reasonable cost. Densimetric data, calculated from the difference between two in situ pressure measurements, exploit variations in real-time streamflow densities to infer SSCs. Unlike other suspendedsediment surrogate technologies based on bulk or digital optics, laser, or hydroacoustics, the accuracy of SSC data estimated using the pressure-difference (also referred to as densimetric) surrogate technology theoretically improves with increasing SCCs. Coupled with streamflow data, continuous suspended-sediment discharges can be calculated using SSC data estimated in real-time using the densimetric technology. The densimetric technology was evaluated at the Rio Puerco in New Mexico, a stream where SSC values regularly range from 10,000-200,000 milligrams per liter (mg/L) and have exceeded 500,000 mg/L. The constant-flow dual-orifice bubbler measures pressure using two precision pressure-transducer sensors at vertically aligned fixed locations in a water column. Water density is calculated from the temperature-compensated differential pressure and SSCs are inferred from the density data. A linear regression model comparing density values to field-measured SSC values yielded an R² of 0.74. Although the application of the densimetric surrogate is likely limited to fluvial systems with SSCs larger than about 10,000 mg/L, based on this and previous studies, the densimetric technology fills a void for monitoring streams with high SSCs.

  8. Physically based method for measuring suspended-sediment concentration and grain size using multi-frequency arrays of acoustic-doppler profilers (United States)

    Topping, David J.; Wright, Scott A.; Griffiths, Ronald; Dean, David


    As the result of a 12-year program of sediment-transport research and field testing on the Colorado River (6 stations in UT and AZ), Yampa River (2 stations in CO), Little Snake River (1 station in CO), Green River (1 station in CO and 2 stations in UT), and Rio Grande (2 stations in TX), we have developed a physically based method for measuring suspended-sediment concentration and grain size at 15-minute intervals using multifrequency arrays of acoustic-Doppler profilers. This multi-frequency method is able to achieve much higher accuracies than single-frequency acoustic methods because it allows removal of the influence of changes in grain size on acoustic backscatter. The method proceeds as follows. (1) Acoustic attenuation at each frequency is related to the concentration of silt and clay with a known grain-size distribution in a river cross section using physical samples and theory. (2) The combination of acoustic backscatter and attenuation at each frequency is uniquely related to the concentration of sand (with a known reference grain-size distribution) and the concentration of silt and clay (with a known reference grain-size distribution) in a river cross section using physical samples and theory. (3) Comparison of the suspended-sand concentrations measured at each frequency using this approach then allows theory-based calculation of the median grain size of the suspended sand and final correction of the suspended-sand concentration to compensate for the influence of changing grain size on backscatter. Although this method of measuring suspended-sediment concentration is somewhat less accurate than using conventional samplers in either the EDI or EWI methods, it is much more accurate than estimating suspended-sediment concentrations using calibrated pump measurements or single-frequency acoustics. Though the EDI and EWI methods provide the most accurate measurements of suspended-sediment concentration, these measurements are labor-intensive, expensive, and

  9. Impact Of Municipal Solid Waste On Trace Metal Concentrations In ...

    African Journals Online (AJOL)

    The impact of municipal solid waste on the levels of cadmium, copper, nickel, lead and zinc in herbage and soil samples within Abuja municipality was studied. The flame atomic absorption spectrophotometry was used in the determination of the metals. The average concentration of Cd, Cu, Ni, Pb and Zn in the herbage ...

  10. The effects of wind and rainfall on suspended sediment concentration related to the 2004 Indian Ocean tsunami. (United States)

    Zhang, XinFeng; Tang, DanLing; Li, ZiZhen; Zhang, FengPan


    The effects of rainfall and wind speed on the dynamics of suspended sediment concentration (SSC), during the 2004 Indian Ocean tsunami, were analyzed using spatial statistical models. The results showed a positive effect of wind speed on SSC, and inconsistent effects (positive and negative) of rainfall on SSC. The effects of wind speed and rainfall on SSC weakened immediately around the tsunami, indicating tsunami-caused floods and earthquake-induced shaking may have suddenly disturbed the ocean-atmosphere interaction processes, and thus weakened the effects of wind speed and rainfall on SSC. Wind speed and rainfall increased markedly, and reached their maximum values immediately after the tsunami week. Rainfall at this particular week exceeded twice the average for the same period over the previous 4years. The tsunami-affected air-sea interactions may have increased both wind speed and rainfall immediately after the tsunami week, which directly lead to the variations in SSC.

  11. Time-series MODIS image-based retrieval and distribution analysis of total suspended matter concentrations in Lake Taihu (China). (United States)

    Zhang, Yuchao; Lin, Shan; Liu, Jianping; Qian, Xin; Ge, Yi


    Although there has been considerable effort to use remotely sensed images to provide synoptic maps of total suspended matter (TSM), there are limited studies on universal TSM retrieval models. In this paper, we have developed a TSM retrieval model for Lake Taihu using TSM concentrations measured in situ and a time series of quasi-synchronous MODIS 250 m images from 2005. After simple geometric and atmospheric correction, we found a significant relationship (R = 0.8736, N = 166) between in situ measured TSM concentrations and MODIS band normalization difference of band 3 and band 1. From this, we retrieved TSM concentrations in eight regions of Lake Taihu in 2007 and analyzed the characteristic distribution and variation of TSM. Synoptic maps of model-estimated TSM of 2007 showed clear geographical and seasonal variations. TSM in Central Lake and Southern Lakeshore were consistently higher than in other regions, while TSM in East Taihu was generally the lowest among the regions throughout the year. Furthermore, a wide range of TSM concentrations appeared from winter to summer. TSM in winter could be several times that in summer.

  12. Retention of Ascorbic Acid and Solid Concentration via Centrifugal Freeze Concentration of Orange Juice

    Directory of Open Access Journals (Sweden)

    P. Orellana-Palma


    Full Text Available Freeze concentration of liquid foods produces high-quality concentrates while retaining the heat-labile compounds found in fresh samples. Centrifugal freeze concentration is a cryoconcentration method assisted by an external force, centrifugation, to enhance the separation of concentrate from the ice. When applying centrifugal freeze concentration to orange juice, after the third cryoconcentration cycle, the ascorbic acid content in the concentrate showed retention close to 70% of the initial value. After the third cycle, the solutes in the concentrate increased 4 times the initial value of the fresh sample with 70% efficiency. The color evaluation showed that the final concentrated fraction was darker than the fresh juice. The centrifugal freeze concentration in orange juice was effective for obtaining a high-quality concentrate with a higher concentration of solids and ascorbic acid retention.

  13. [Remote sensing estimation of total suspended matter concentration in Xin'anjiang Reservoir using Landsat 8 data]. (United States)

    Zhang, Yi-bo; Zhang, Yun-lin; Zha, Yong; Shi, Kun; Zhou, Yong-qiang; Wang, Ming-zhu


    Total suspended matter (TSM) plays an important role in determining the underwater light climate, which then affects the lake primary production. Therefore, TSM concentration is an important parameter for lake water quality and water environment assessment. This study developed an empirical estimation model and presented the spatial distribution of TSM concentration for the relatively clear Xin'anjiang Reservoir based on the in situ ground data and the matching Landsat 8 data. The results showed that Band 2, Band 3 and Band 8 of Landsat 8 data were the sensitive bands of TSM estimation in Xin'anjiang Reservoir with the linear determination coefficients of 0.37, 0.51 and 0.42, respectively. However, the linear models using Band 2, Band 3 and Band 8 could not give a reasonable and satisfying estimation accuracy. Therefore, a three-band combination estimation model of TSM concentration using Band 2, Band 3 and Band. 8 was calibrated and validated to improve the TSM concentration estimation accuracy. The determination coefficient, mean relative error and root mean square error were 0.92, 11% and 0.16 mg x L(-1), respectively for the three-band combination model. Overall, the TSM concentration was relatively low in Xin'anjiang Reservoir, ranging from 0. 04 to 24. 54 mg x L(-1) with a mean value of 2.19 mg x L(-1). Higher TSM concentrations were distributed in the nearshore zones and small bays such as Fengshuling bay, Fenkou bay, Weiping bay, Anyang bay, Dashu bay and Linqi bay, which were affected by input rivers rainfall and human dredging activity. Therefore, this study demonstrated that the combination of three bands using Landsat 8 data could be used to estimate the TSM concentration in the relatively clear Xin'anjiang Reservoir.

  14. The use of hand-held 35 mm color infrared imagery for estimates of suspended solids - A progress report. [in water pollution monitoring (United States)

    Miller, W. F.; Whisler, F. D.; Robinette, H. R.; Finnie, D.; Cannon, T.


    A cost-effective aerial surveillance technique is proposed for detection and identification of suspended solids which would be operational for both governmental monitoring organizations and private individuals operating catfish farms. Sixteen catfish ponds were flown daily for seven days using two hand-held 35 mm cameras with both Kodachrome X and Ektachrome infrared film. Hue, value, and chroma designations were recorded for each pond on each date by three interpreters, and the accepted color was that recorded by at least two of the interpreters, or if there was a three hue range, the median was accepted. Relations between suspended solids and color designations were analyzed graphically, and chroma was discarded due to an apparent lack of correlation. The data obtained were then analyzed by multiple regression. Significant correlations were revealed between hue and value and total and inorganic suspended solids. If perfected, this technique could be developed to sufficent accuracy for large-scale reconnaissance surveys to monitor the quality of rivers and streams.

  15. Resuspension and transport of suspended solids in Eurajoensalmi Bay. Final report of monitoring activities in 2009-2011; Resuspensio ja kiintoaineen kulkeutuminen Eurajoensalmessa. Vesistoemittausten loppuraportti

    Energy Technology Data Exchange (ETDEWEB)

    Mykkanen, J.; Kiirikki, M.; Lindfors, A. [Luode Consulting Oy, Espoo (Finland)


    The goal of monitoring activities carried out in Eurajoensalmi Bay was to indentify factors affecting dispersal of river waters and suspended solid matter in the estuary area. In addition to suspended solids load and dispersal of river water, also release of sedimented particles from the sea bed in resuspension was studied. River water quality and discharge as well as resuspension in Eurajoensalmi estuary area were monitored with Luode automatic monitoring stations equipped with water quality, water level, wave height and weather sensors. Dynamics of Eurajoensalmi estuary area was studied by installing profiling current meters (ADCP) and water quality sensors to the sea floor at the mouth of Eurajoensalmi. Spatial variation of surface water quality was monitored with a flow-through method from a moving vessel and manual profiling several times during the monitoring period. Collected data was processed and used in determining suspended solids balance of Eurajoensalmi Bay. The balance was determined by creating a regression model for water exchange and sediment flux over the cross section at the mouth of Eurajoensalmi. Regression model was created also to determine resuspension in Eurajoensalmi area. Sediment flux and resuspension were modeled using long term wind data from Kylmaepihlaja meteorological station as a variable to determine overall sediment balance of Eurajoensalmi.

  16. Estimating concentrations of fine-grained and total suspended sediment from close-range remote sensing imagery (United States)

    Mosbrucker, Adam; Spicer, Kurt R.; Christianson, Tami; Uhrich, Mark A.


    Fluvial sediment, a vital surface water resource, is hazardous in excess. Suspended sediment, the most prevalent source of impairment of river systems, can adversely affect flood control, navigation, fisheries and aquatic ecosystems, recreation, and water supply (e.g., Rasmussen et al., 2009; Qu, 2014). Monitoring programs typically focus on suspended-sediment concentration (SSC) and discharge (SSQ). These time-series data are used to study changes to basin hydrology, geomorphology, and ecology caused by disturbances. The U.S. Geological Survey (USGS) has traditionally used physical sediment sample-based methods (Edwards and Glysson, 1999; Nolan et al., 2005; Gray et al., 2008) to compute SSC and SSQ from continuous streamflow data using a sediment transport-curve (e.g., Walling, 1977) or hydrologic interpretation (Porterfield, 1972). Accuracy of these data is typically constrained by the resources required to collect and analyze intermittent physical samples. Quantifying SSC using continuous instream turbidity is rapidly becoming common practice among sediment monitoring programs. Estimations of SSC and SSQ are modeled from linear regression analysis of concurrent turbidity and physical samples. Sediment-surrogate technologies such as turbidity promise near real-time information, increased accuracy, and reduced cost compared to traditional physical sample-based methods (Walling, 1977; Uhrich and Bragg, 2003; Gray and Gartner, 2009; Rasmussen et al., 2009; Landers et al., 2012; Landers and Sturm, 2013; Uhrich et al., 2014). Statistical comparisons among SSQ computation methods show that turbidity-SSC regression models can have much less uncertainty than streamflow-based sediment transport-curves or hydrologic interpretation (Walling, 1977; Lewis, 1996; Glysson et al., 2001; Lee et al., 2008). However, computation of SSC and SSQ records from continuous instream turbidity data is not without challenges; some of these include environmental fouling, calibration, and

  17. suspended solids and metals

    African Journals Online (AJOL)

    33.084722,. −117.300000). Lake Ellyn. Rectangle n/a. Striegl and Cowan. (1987) ..... V pp. /D pp. (12). T o tal. TS. S. No n e. +0.86. D p p. (12). T o tal. Pb Zn. B elow m ed ian. A b o ve m ed ian. −. 0.9. 6. −. 0.82. Pb. B elo w an d ab o ve m ed ian. −.

  18. Extracellular polymeric substances, microbial activity and microbial community of biofilm and suspended sludge at different divalent cadmium concentrations. (United States)

    Wang, Zichao; Gao, Mengchun; Wei, Junfeng; Ma, Kedong; Zhang, Jing; Yang, Yusuo; Yu, Shuping


    The differences between biofilm and suspended sludge (S-sludge) in extracellular polymeric substances (EPS), microbial activity, and microbial community in an anoxic-aerobic sequencing batch biofilm reactor (SBBR) at different concentrations of divalent cadmium (Cd(II)) were investigated. As the increase of Cd(II) concentration from 0 to 50mgL(-1), the specific ammonium oxidation rate (SAOR), specific nitrite oxidation rate (SNOR), and specific nitrate reduction rate (SNRR) of biofilm decreased from 4.85, 5.22 and 45mgNg(-1) VSSh(-1) to 1.54, 2.38 and 26mgNg(-1)VSSh(-1), respectively, and the SAOR, SNOR and SNRR of S-sludge decreased from 4.80, 5.02 and 34mgNg(-1)VSSh(-1) to 1.46, 2.20 and 17mgNg(-1)VSSh(-1), respectively. Biofilm had higher protein (PN) content in EPS than S-sludge. Contrast to S-sludge, biofilm could provide Nitrobacter vulgaris, beta proteobacterium INBAF015, and Pseudoxanthomonas mexicana with the favorable conditions of growth and reproduction. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Effect of Hydrograph Separation on Suspended Sediment Concentration Predictions in a Forested Headwater with Thick Soil and Weathered Gneiss Layers

    Directory of Open Access Journals (Sweden)

    Naoki Kabeya


    Full Text Available Two-component hydrograph separation using oxygen-18 concentrations was conducted at a sediment runoff observation weir installed in a small subcatchment of a forested gneiss catchment in Japan. The mean soil thickness of this catchment is 7.27 m, which comprises 3.29 m of brown forest soil (A and B layers and a 3.98-m layer of heavily weathered gneiss. Data were collected for a storm on 20–21 May 2003, and the percentage of event water separated by the stable isotope ratio in comparison with the total rainfall amount was about 1%. This value is within the ratio of a riparian zone in a drainage area. Temporal variation of suspended sediment concentration exhibited higher correlation with the event water component than with the total runoff or pre-event water component. This shows that the riparian zone causes rainwater to flow out quickly during a rain event, and that this is an important area of sediment production and transportation in a forested headwater with thick soil and weathered gneiss layers.

  20. Transformation and sorption of illicit drug biomarkers in sewer systems: understanding the role of suspended solids in raw wastewater

    DEFF Research Database (Denmark)

    Ramin, Pedram; Brock, Andreas Libonati; Polesel, Fabio


    substrates (primary metabolic processes) and transformation of illicit drug biomarkers (secondary metabolic processes) by suspended biomass. Sixteen drug biomarkers were targeted, including mephedrone, methadone, cocaine, heroin, codeine and tetrahydrocannabinol (THC) and their major human metabolites. Batch...

  1. Removal of Cs{sup +}, Sr{sup 2+}, and Co{sup 2+} ions from the mixture of organics and suspended solids aqueous solutions by zeolites

    Energy Technology Data Exchange (ETDEWEB)

    Fang, Xiang Hong; Fang, Fang; Lu, Chun Hai [College of Nuclear Technology and Automation Engineering, Chengdu University of Technology, Chengdu (China); Zheng, Lei [Southwest University of Science and Technology, Key Laboratory of Solid Waste Treatment and Resource Recycle, Ministry of Education, Mianyang (China)


    Serving as an excellent adsorbent and inorganic ion exchanger in the water purification field, zeolite 4A has in this work presented a strong capability for purifying radioactive waste, such as Sr{sup 2+}, Cs{sup +}, and Co{sup 2+} in water. During the processes of decontamination and decommissioning of suspended solids and organics in low-level radioactive wastewater, the purification performance of zeolite 4A has been studied. Under ambient temperature and neutral condition, zeolite 4A absorbed simulated radionuclides such as Sr{sup 2+}, Cs{sup +}, and Co{sup 2+} with an absorption rate of almost 90%. Additionally, in alkaline condition, the adsorption percentage even approached 98.7%. After conducting research on suspended solids and organics of zeolite 4A for the treatment of radionuclides, it was found that the suspended clay was conducive to absorption, whereas the absorption of organics in solution was determined by the species of radionuclides and organics. Therefore, zeolite 4A has considerable potential in the treatment of radioactive wastewater.

  2. Removal of Cs+, Sr2+, and Co2+ Ions from the Mixture of Organics and Suspended Solids Aqueous Solutions by Zeolites

    Directory of Open Access Journals (Sweden)

    Xiang-Hong Fang


    Full Text Available Serving as an excellent adsorbent and inorganic ion exchanger in the water purification field, zeolite 4A has in this work presented a strong capability for purifying radioactive waste, such as Sr2+, Cs+, and Co2+ in water. During the processes of decontamination and decommissioning of suspended solids and organics in low-level radioactive wastewater, the purification performance of zeolite 4A has been studied. Under ambient temperature and neutral condition, zeolite 4A absorbed simulated radionuclides such as Sr2+, Cs+, and Co2+ with an absorption rate of almost 90%. Additionally, in alkaline condition, the adsorption percentage even approached 98.7%. After conducting research on suspended solids and organics of zeolite 4A for the treatment of radionuclides, it was found that the suspended clay was conducive to absorption, whereas the absorption of organics in solution was determined by the species of radionuclides and organics. Therefore, zeolite 4A has considerable potential in the treatment of radioactive wastewater.

  3. Improved estimates of filtered total mercury loadings and total mercury concentrations of solids from potential sources to Sinclair Inlet, Kitsap County, Washington (United States)

    Paulson, Anthony J.; Conn, Kathleen E.; DeWild, John F.


    . Studies of groundwater in the other two fill areas were conducted under worst-case higher high tidal conditions. A December 2011 study found that concentrations of filtered total mercury in the well in the fill area on the eastern boundary of the Bremerton naval complex were less than or equal to 11 nanograms per liter, indicating that releases from the eastern area were unlikely. In addition, concentrations of total mercury of solids were low (<3 milligrams per kilogram). In contrast, data from the November 2011 study indicated that the concentrations of filtered total mercury in the well located in the central fill area had tidally influenced concentrations of up to 500 nanograms per liter and elevated concentrations of total mercury of solids (29–41 milligrams per kilogram). This suggests that releases from this area, which has not been previously studied in detail, may be substantial. Previous measurements of total mercury of suspended solids in the dry dock discharges revealed high concentration of total mercury when suspended-solids concentrations were low. However, this result could have been owing to bias from sequential sampling during changing suspended‑solids concentrations. Sampling of two dry dock systems on the complex in a manner that precluded this bias confirmed that suspended-solids concentrations and total mercury concentrations of suspended solids varied considerably during pumping cycles. These new data result in revised estimates of solids loadings from the dry docks. Although most of the solids discharged by the dry docks seem to be recycled Operable Unit B Marine sediment, a total of about 3.2 metric tons of solids per year containing high concentrations of total mercury were estimated to be discharged by the two dry dock systems. A simple calculation, in which solids (from dry docks, the steam plant, and tidal flushing of the largest stormwater drain) are widely dispersed throughout Operable Unit B Marine, suggests that Bremerton naval complex

  4. A Semi-Analytical Model for Remote Sensing Retrieval of Suspended Sediment Concentration in the Gulf of Bohai, China

    Directory of Open Access Journals (Sweden)

    Jin-Ling Kong


    Full Text Available Suspended sediment concentration (SSC is one of the most critical parameters in ocean ecological environment evaluation and it can be determined using ocean color remote sensing (RS. The purpose of this study is to develop a model that provides a reliable and sensitive evaluation of SSC retrieval using RS data. Data were acquired for and gathered from the Gulf of Bohai where SSC levels are relatively low with an average value below 30 mg·L−1. The study indicates that the most sensitive band to SSC levels in the study area is the NIR band of Landsat5 TM images. A quadratic polynomial semi-analytical model appears to be the best retrieval model based on the relationship between the inherent optical properties (IOPs and apparent optical properties (AOPs of water as described by the quasi-analytical algorithm (QAA. The model has a higher precision and effectiveness for SSC retrieval than data-driven statistical models, especially when SSC level is relatively high. The average relative error and the root mean square error (RMSE are 12.32% and 4.53 mg·L−1, respectively, while the correlation coefficient between observed and estimated SSC by the model is 0.95. Using the proposed retrieval model and TM data, SSC levels of the entire study region in the Gulf of Bohai were estimated. These estimates can serve as the baseline for efficient monitoring of the ocean environment in the future.

  5. A MODIS-Based Retrieval Model of Suspended Particulate Matter Concentration for the Two Largest Freshwater Lakes in China

    Directory of Open Access Journals (Sweden)

    Fangyuan Chen


    Full Text Available Suspended particulate matter concentration (CSPM is a key parameter describing case-II water quality. Empirical and semi-empirical models are frequently developed and applied for estimating CSPM values from remote sensing images; however, they are usually region- or season-dependent. This study aimed to develop a Moderate Resolution Imaging Spectroradiometer (MODIS-based retrieval model of CSPM for Poyang and Dongting Lake together. The 89 CSPM measurements in Poyang and Dongting Lake as well as their corresponding MODIS Terra images were used to calibrate CSPM retrieval models, and the calibration results showed that the exponential models of MODIS red band and red minus shortwave infrared (SWIR band at 1240 nm both explained about 76% of the variation of CSPM of Poyang and Dongting Lake together. When the two models were applied to the validation datasets, the results indicated that the exponential model of red band obtained more stable CSPM estimations with no bias at a significance level of 0.05 in both lakes. The MODIS red-band-based model achieved acceptable results for estimating CSPM in both Poyang and Dongting Lake, and it provided a foundation for obtaining comparable spatiotemporal information of CSPM, which will be helpful for comparing, understanding, managing, and protecting the two aquatic ecosystems.

  6. Effect of Feedstock Concentration on Biogas Production by Inoculating Rumen Microorganisms in Biomass Solid Waste. (United States)

    Li, Na; Yang, Fenglin; Xiao, Huining; Zhang, Jian; Ping, Qingwei


    A methane production system with continuous stirred-tank reactor, rumen liquid as inoculate microorganisms, and paper mill excess sludge (PES) as feedstock was studied. The work mainly focused on revealing the effect of feedstock concentration on the biogas production, which was seldom reported previously for the current system. The optimal fermentation conditions were found as follows: pH = 7, T = 39 ± 1 °C, sludge retention time is 20 days, sludge with total solids (TS) are 1, 2, 3.5, 5, 10, and 13% in weight. Daily gas yields were measured, and biogas compositions were analyzed by gas chromatograph. Under such conditions, the optimum input TS was 10 wt%, and the biogas yield and volume gas productivity were 280.2 mL/g·TS and 1188.4 mL L-1·d-1, respectively. The proportions of CH4 and CO2 in the biogas were 65.1 and 34.2%. The CH4 yield reached 182.7 mL/g VS (volatile suspended solid), which was higher than previously reported values. The findings of this work have a significant effect on promoting the application of digesting PES by rumen microorganisms and further identified the technical parameter.

  7. Effects of wind farm construction on concentrations and fluxes of dissolved organic carbon and suspended sediment from peat catchments at Braes of Doune, central Scotland

    Directory of Open Access Journals (Sweden)

    I. Grieve


    Full Text Available This paper assesses the impacts of disturbance associated with the construction of a wind farm on fluxes of dissolved organic carbon (DOC and suspended sediment from a blanket peat catchment in central Scotland during the period immediately following completion of construction. Six streams draining the site were sampled on six dates from October 2006, when construction was completed, and an additional three control streams to the west of the site were sampled on the same dates. Turbidity and stage were recorded semi-continuously in the two largest streams (one disturbed and one control, which were also sampled during storm events. Absorbance (400 nm and DOC concentrations were determined on all samples, and suspended sediment was determined on the event samples. Absorbance and DOC were closely correlated in both the disturbed and undisturbed streams, with slightly greater absorbance per unit DOC in the disturbed streams. DOC concentrations in disturbed tributaries were always greater than those in undisturbed streams, with mean differences ranging from 2 to around 5 mg L-1. DOC and stage were positively correlated during events with maximum concentrations in excess of 30 mg L 1 at peak flow. Suspended sediment concentrations were markedly elevated in the disturbed stream with maximum concentrations at peak flow some 4–5 times greater than in the control. The colour of the sediment suggested that it was highly organic in nature at peak flow, and suspended particulate organic carbon represented a further loss of C from the site. Using flow-weighted mean DOC concentrations calculated for the storms monitored in autumn 2007, dissolved carbon losses can be estimated for the catchments of the disturbed and control streams. From these data the additional DOC loss related to disturbance associated with the wind farm is estimated at 5 g m-2.

  8. Investigation on dynamic calibration for an optical-fiber solids concentration probe in gas-solid two-phase flows. (United States)

    Xu, Guiling; Liang, Cai; Chen, Xiaoping; Liu, Daoyin; Xu, Pan; Shen, Liu; Zhao, Changsui


    This paper presents a review and analysis of the research that has been carried out on dynamic calibration for optical-fiber solids concentration probes. An introduction to the optical-fiber solids concentration probe was given. Different calibration methods of optical-fiber solids concentration probes reported in the literature were reviewed. In addition, a reflection-type optical-fiber solids concentration probe was uniquely calibrated at nearly full range of the solids concentration from 0 to packed bed concentration. The effects of particle properties (particle size, sphericity and color) on the calibration results were comprehensively investigated. The results show that the output voltage has a tendency to increase with the decreasing particle size, and the effect of particle color on calibration result is more predominant than that of sphericity.

  9. Investigation on Dynamic Calibration for an Optical-Fiber Solids Concentration Probe in Gas-Solid Two-Phase Flows

    Directory of Open Access Journals (Sweden)

    Changsui Zhao


    Full Text Available This paper presents a review and analysis of the research that has been carried out on dynamic calibration for optical-fiber solids concentration probes. An introduction to the optical-fiber solids concentration probe was given. Different calibration methods of optical-fiber solids concentration probes reported in the literature were reviewed. In addition, a reflection-type optical-fiber solids concentration probe was uniquely calibrated at nearly full range of the solids concentration from 0 to packed bed concentration. The effects of particle properties (particle size, sphericity and color on the calibration results were comprehensively investigated. The results show that the output voltage has a tendency to increase with the decreasing particle size, and the effect of particle color on calibration result is more predominant than that of sphericity.

  10. The influence of grain size, grain color, and suspended-sediment concentration on light attenuation: why fine-grained terrestrial sediment is bad for coral reef ecosystems (United States)

    Storlazzi, Curt; Norris, Benjamin; Rosenberger, Kurt


    Sediment has been shown to be a major stressor to coral reefs globally. Although many researchers have tested the impact of sedimentation on coral reef ecosystems in both the laboratory and the field and some have measured the impact of suspended sediment on the photosynthetic response of corals, there has yet to be a detailed investigation on how properties of the sediment itself can affect light availability for photosynthesis. We show that finer-grained and darker-colored sediment at higher suspended-sediment concentrations attenuates photosynthetically active radiation (PAR) significantly more than coarser, lighter-colored sediment at lower concentrations and provide PAR attenuation coefficients for various grain sizes, colors, and suspended-sediment concentrations that are needed for biophysical modeling. Because finer-grained sediment particles settle more slowly and are more susceptible to resuspension, they remain in the water column longer, thus causing greater net impact by reducing light essential for photosynthesis over a greater duration. This indicates that coral reef monitoring studies investigating sediment impacts should concentrate on measuring fine-grained lateritic and volcanic soils, as opposed to coarser-grained siliceous and carbonate sediment. Similarly, coastal restoration efforts and engineering solutions addressing long-term coral reef ecosystem health should focus on preferentially retaining those fine-grained soils rather than coarse silt and sand particles.

  11. Improving the description of the suspended particulate matter concentrations in the southern North Sea through assimilating remotely sensed data

    NARCIS (Netherlands)

    El Serafy, G.Y.; Eleveld, M.A.; Blaas, M.; van Kessel, T.; Gaytan Aguilar, S.; van der Woerd, H.J.


    The integration of remote sensing data of suspended particulate matter (SPM) into numerical models is useful to improve the understanding of the temporal and spatial behaviour of SPM in dynamic shelf seas. In this paper a generic method based on the Ensemble Kalman Filtering (EnKF) for assimilating

  12. Concentrations and transport of suspended sediment, nutrients, and pesticides in the lower Mississippi-Atchafalaya River subbasin during the 2011 Mississippi River flood, April through July (United States)

    Welch, Heather L.; Coupe, Richard H.; Aulenbach, Brent T.


    High streamflow associated with the April–July 2011 Mississippi River flood forced the simultaneous opening of the three major flood-control structures in the lower Mississippi-Atchafalaya River subbasin for the first time in history in order to manage the amount of water moving through the system. The U.S. Geological Survey (USGS) collected samples for analysis of field properties, suspended-sediment concentration, particle-size, total nitrogen, nitrate plus nitrite, total phosphorus, orthophosphate, and up to 136 pesticides at 11 water-quality stations and 2 flood-control structures in the lower Mississippi-Atchafalaya River subbasin from just above the confluence of the upper Mississippi and Ohio Rivers downstream from April through July 2011. Monthly fluxes of suspended sediment, suspended sand, total nitrogen, nitrate plus nitrite, total phosphorus, orthophosphate, atrazine, simazine, metolachlor, and acetochlor were estimated at 9 stations and 2 flood-control structures during the flood period. Although concentrations during the 2011 flood were within the range of what has been observed historically, concentrations decreased during peak streamflow on the lower Mississippi River. Prior to the 2011 flood, high concentrations of suspended sediment and nitrate were observed in March 2011 at stations downstream of the confluence of the upper Mississippi and Ohio Rivers, which probably resulted in a loss of available material for movement during the flood. In addition, the major contributor of streamflow to the lower Mississippi-Atchafalaya River subbasin during April and May was the Ohio River, whose water contained lower concentrations of suspended sediment, pesticides, and nutrients than water from the upper Mississippi River. Estimated fluxes for the 4-month flood period were still quite high and contributed approximately 50 percent of the estimated annual suspended sediment, nitrate, and total phosphorus fluxes in 2011; the largest fluxes were estimated at

  13. Concentration of lead, cadmium, and iron in sediment dust and total suspended particles before and after initialisation of integral production in iron and steel work plant Zenica. (United States)

    Prcanović, Halim; Duraković, Mirnes; Beganović, Sanela


    Poor air quality is a common fact for all areas with base industry. The city of Zenica was once the metallurgical centre of Ex-Yugoslavia and is therefore highly polluted at present. Air pollution peaked in 1987 when average concentration of pollutants was extremely high (daily average concentration of SO(2) was 1800 μg m(-3)). With the beginning of the war in 1992, integral production in the steel work plant was shut down, to be re-launched in 2008. Limit values for iron do not exist, but iron has been monitored in Zenica for the past 28 years because of the presence of steel works. Concentrations of cadmium and lead have also been measured because they are very much present in polluted areas with steel works. The concentration of mentioned elements in air deposit and total suspended particles before and after integral production in the steel work plant was re-launched is the subject of this paper. Total suspended particles were measured in two locations using German standard VDI 2463 Blatt 4. Sediment dust was measured in nine locations using Bergerhoff method. The concentration of iron, lead, and cadmium was performed in the chemical laboratory of the Metallurgical Institute "Kemal Kapetanović" Zenica using standard methods. Higher concentrations of these parameters during the period of integral production clearly point to the impact of steel works on Zenica valley.

  14. An investigation of spatial variation of suspended sediment concentration induced by a bay bridge based on Landsat TM and OLI data (United States)

    Cai, LiNa; Tang, DanLing; Li, CongYing


    This study investigates the spatial variation of suspended sediment concentration (SSC) induced by Hangzhou Bay Bridge (HBB) in the coastal waters of the East China Sea. Based on Landsat Thematic Mapper (TM), Operational Land Imager (OLI) data and in-situ measurements, spectral characteristics of waters in Hangzhou Bay and SSC retrieved from near infrared single band have been analyzed. The results revealed significant difference of SSC in the water on two sides of HBB. SSC increases downstream of the bridge under conditions of low turbidity (SSC 400 mg l-1) upstream. This study shows that the interaction of bridge piers and currents has important influences on SSC distribution by inducing hydrodynamic factors and by changing suspended sediment transport. Remotely sensed data with high spatial resolution as TM and OLI can be applied to investigate SSC variations induced by a bridge in the bay area.

  15. Monitoring the effects of disposal of fine sediments from maintenance dredging on suspended particulate matter concentration in the Belgian nearshore area (southern North Sea). (United States)

    Fettweis, Michael; Baeye, Matthias; Francken, Frederic; Lauwaert, Brigitte; Van den Eynde, Dries; Van Lancker, Vera; Martens, Chantal; Michielsen, Tinne


    The impact of continuous disposal of fine-grained sediments from maintenance dredging works on the suspended particulate matter concentration in a shallow nearshore turbidity maximum was investigated during dredging experiment (port of Zeebrugge, southern North Sea). Before, during and after the experiment monitoring of SPM concentration using OBS and ADV altimetry was carried out at a location 5 km west of the disposal site. A statistical analysis, based on the concept of populations and sub-sampling, was applied to evaluate the effect. The data revealed that the SPM concentration near the bed was on average more than two times higher during the dredging experiment. The disposed material was mainly transported in the benthic layer and resulted in a long-term increase of SPM concentration and formation of fluid mud layers. The study shows that SPM concentration can be used as an indicator of environmental changes if representative time series are available. Copyright © 2010 Elsevier Ltd. All rights reserved.

  16. Use of acoustic backscatter to estimate continuous suspended sediment and phosphorus concentrations in the Barton River, northern Vermont, 2010-2013 (United States)

    Medalie, Laura; Chalmers, Ann T.; Kiah, Richard G.; Copans, Benjamin


    The U.S. Geological Survey, in cooperation with the Vermont Department of Environmental Conservation, investigated the use of acoustic backscatter to estimate concentrations of suspended sediment and total phosphorus at the Barton River near Coventry, Vermont. The hypothesis was that acoustic backscatter—the reflection of sound waves off objects back to the source from which they came—measured by an acoustic Doppler profiler (ADP) and recorded as ancillary data for the calculation of discharge, also could be used to generate a continuous concentration record of suspended sediment and phosphorus at the streamgage, thereby deriving added value from the instrument. Suspended-sediment and phosphorus concentrations are of particular interest in Vermont, where impairment of surface waters by suspended sediments and phosphorus is a major concern. Regression models for estimating suspended-sediment concentrations (SSCs) and total phosphorus concentrations evaluated several independent variables: measured backscatter (MB), water-corrected backscatter (WCB), sediment-corrected backscatter (SCB), discharge, fluid-absorption coefficient, sediment-driven acoustic attenuation coefficient, and discharge hysteresis. The best regression equations for estimating SSC used backscatter as the predictor, reflecting the direct relation between acoustic backscatter and SSC. Backscatter was a better predictor of SSC than discharge in part because hysteresis between SSC and backscatter was less than for SSC and discharge. All three backscatter variables—MB, WCB, and SCB—performed equally as predictors of SSC and phosphorus concentrations at the Barton River site. The similar abilities to predict SSC among backscatter terms may partially be attributed to the low values and narrow range of the sediment-driven acoustic attenuation in the Barton River. The regression based on SCB was selected for estimating SSC because it removes potential bias caused by attenuation and temperature

  17. Suspended-sediment concentrations, bedload, particle sizes, surrogate measurements, and annual sediment loads for selected sites in the lower Minnesota River Basin, water years 2011 through 2016 (United States)

    Groten, Joel T.; Ellison, Christopher A.; Hendrickson, Jon S.


    Accurate measurements of fluvial sediment are important for assessing stream ecological health, calculating flood levels, computing sediment budgets, and managing and protecting water resources. Sediment-enriched rivers in Minnesota are a concern among Federal, State, and local governments because turbidity and sediment-laden waters are the leading impairments and affect more than 6,000 miles of rivers in Minnesota. The suspended sediment in the lower Minnesota River is deleterious, contributing about 75 to 90 percent of the suspended sediment being deposited into Lake Pepin. The Saint Paul District of the U.S. Army Corps of Engineers and the Lower Minnesota River Watershed District collaborate to maintain a navigation channel on the lower 14.7 miles of the Minnesota River through scheduled dredging operations. The Minnesota Pollution Control Agency has adopted a sediment-reduction strategy to reduce sediment in the Minnesota River by 90 percent by 2040.The U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, the Minnesota Pollution Control Agency, and the Lower Minnesota River Watershed District, collected suspended-sediment, bedload, and particle-size samples at five sites in the lower Minnesota River Basin during water years 2011 through 2014 and surrogate measurements of acoustic backscatter at one of these sites on the lower Minnesota River during water years 2012 through 2016 to quantify sediment loads and improve understanding of sediment-transport relations. Annual sediment loads were computed for calendar years 2011 through 2014.Data collected from water years 2011 through 2014 indicated that two tributaries, Le Sueur River and High Island Creek, had the highest sediment yield and concentrations of suspended sediment. These tributaries also had greater stream gradients than the sites on the Minnesota River. Suspended fines were greater than suspended sand at all sites in the study area. The range of median particle sizes matched

  18. Remote Sensing and Water Quality Indicators in the West Flood Canal Semarang City: Spatio-temporal Structures of Lansat-8 Derived Chlorophyll-a and Total Suspended Solids (United States)

    Subiyanto, Sawitri


    One of the waters that has been contaminated by industrial waste and domestic waste is the waters of West Flood Canal in Semarang City which is the estuary of the river system, which passes through the Western City of Semarang which is dense with residential and industrial. So, it is necessary to have information about the assessment of water quality in the estuary of the West Flood Canal. Remote sensing technology can analyze the results of recording the spectral characteristics of water with water quality parameters. One of the parameters for assessing water quality is Chlorophyll-a and Total Suspended Solid, can be estimated through remote sensing technology using multispectral Lansat-8 Satellite images data from April, June, and August, 2017 and there are three selected algorithms. Based on the results of TSS and Chlorophyll-A processing, the TSS shows values greater than or equal to 100 which can be said that West Flood Canal is damaged (hypertrophic). While the chlorophyll-a shows a value less than 100 indicating Eutrophic status (threatened). This is caused by the number of suspended materials in the water surface and also because of the disturbance of water vegetation in the form of weeds that destroy the function of the actual West Canal Flood.

  19. Decline in suspended sediment concentration delivered by the Changjiang (Yangtze) River into the East China Sea between 1956 and 2013 (United States)

    Dai, Zhijun; Fagherazzi, Sergio; Mei, Xuefei; Gao, Jinjuan


    The temporal evolution of suspended sediment concentration (SSC) in a river debouching into the ocean provides vital insights into erosion processes in the watershed and dictates the evolution of the inner continental shelf. While the delivery of sediment from rivers to the ocean has received special attention in the recent past, few studies focused on the variability and dynamics of river SSC, especially in the Changjiang (Yangtze) river, China, the longest river in Asia. Here, variations in SSC delivered by the Changjiang River to the East China Sea and possible causes of its variability were detected based on a long-term time series of daily SSC and monthly water discharge measured at the Datong gauging station. The SSC data are further compared to a hydrological analysis of yearly precipitation covering the entire catchment. The results indicate the presence of a decline in SSC in the period 1956-2013, which can be divided into three phases: (i) high SSC (0.69 kg/m3) in the wet season and low SSC (0.2 kg/m3) in the dry season from 1956 to 1970; (ii) relative high SSC (0.58 kg/m3) in the wet season and low SSC (0.15 kg/m3) in the dry season from 1971 to 2002; and (iii) low SSC (0.19 kg/m3) in the wet season and very low SSC (0.09 kg/m3) in the dry season after 2002. These three periods have a mean yearly SSC values of 0.62, 0.42, and 0.18 kg/m3, respectively. Compared with 1956-1970, the slope of the rating curve between SSC and water discharge decreased, respectively, by 2% and 30% during the period 1971-2002 and 2002-2013. Soil erosion, dam construction, and banks reinforcement along the Changjiang River are the main causes of SSC variations. Fluctuations in water discharge are also controlling the SSC long-term variations. Specifically, from 1956 to 1970, the effect of soil erosion overrules that of dam impoundment, which is likely responsible for the high SSC; during the period 1970-2002, the influence of dam impoundment increases while that of soil erosion

  20. Filtration and clearance rates of Anadara grandis juveniles (Pelecypoda, Arcidae with different temperatures and suspended matter concentrations

    Directory of Open Access Journals (Sweden)

    Anselmo Miranda-Baeza


    Full Text Available The mangrove cockle Anadara grandis (Broderip and Sowerby, 1829 is a potential candidate for aquaculture and for bioremediation of aquaculture effluents in the tropical and subtropical coastal areas of the eastern Pacific Ocean. Laboratory-produced spat are available, but there is no information on their responses to the range of environmental conditions to which they might be subject during the growth cycle. The aim of this study was to evaluate the filtration and clearance rates of A. grandis spat (shell length 9.50±0.37 mm with a food concentration (7.5 mg∙l-1 at four different temperatures (22, 25, 28 and 31 ºC, with pH = 7.5±0.2 and O2 concentration of 6.4±0.5 mg·l-1; experiment one; and with a temperature (25 °C and five concentrations of suspended matter (from 7.5 to 29 mg·l-1 and pH and O2 values of 7.9±0.2 and 6.8± 0.4 mg·l-1; experiment two. Filtration and clearance rates were highest at 25 ºC and significantly different (p.05. In the second experiment filtration increased according to the amount of food available, but there were no significant differences (p>.05 between 7.5 and 11 mg·l-1 and from 22.4 to 29 mg·l-1. The trend was similar for clearance, and in this case significant differences were found (pLa almeja Anadara grandis (Broderip and Sowerby, 1829 es un candidato potencial para la acuicultura y la biorremediación de efluentes acuícolas en las áreas costeras tropicales y subtropicales del océano Pacífico oriental. Se dispone de semilla producida en laboratorio, sin embargo no hay información sobre sus respuestas a los intervalos de las condiciones ambientales a las cuales puede estar sujeta durante el periodo de crecimiento. El objetivo de este estudio fue evaluar las tasas de filtración y de clarificación de semilla de A. grandis (largo de la concha= 9.50±0.37 mm con una concentración de alimento (7.5 mg∙l-1 y cuatro diferentes temperaturas (22, 25, 28 y 31 °C con pH= 7.5±0.2, concentración de O

  1. Characterization of naproxen-loaded solid SMEDDSs prepared by spray drying: the effect of the polysaccharide carrier and naproxen concentration. (United States)

    Čerpnjak, Katja; Zvonar, Alenka; Vrečer, Franc; Gašperlin, Mirjana


    The purpose of this study was to prepare solid SMEDDS (sSMEDDS) particles produced by spray-drying using maltodextrin (MD), hypromellose (HPMC), and a combination of the two as a solid carrier. Naproxen (NPX) as the model drug was dissolved (at 6% concentration) or partially suspended (at 18% concentration) in a liquid SMEDDS composed of Miglyol(®) 812, Peceol™, Gelucire(®) 44/14, and Solutol(®) HS 15. Among the sSMEDDSs tested, the MD-based sSMEDDSs (with a granular, smooth-surfaced, microspherical appearance) preserved the self-microemulsifying properties of liquid SMEDDSs and exhibited dissolution profiles similar to those of liquid SMEDDSs, irrespective of the concentration of NPX. In contrast, HPMC-based sSMEDDSs (irregular-shaped microparticles) exhibited slightly prolonged release times due to the polymeric nature of the carrier. Differential scanning calorimetry (DSC), X-ray powder diffraction (XRPD), and Raman mapping analysis confirmed molecularly dissolved NPX (at 6% of drug loading), whereas at 18% NPX loading drug is partially molecularly dissolved and partially in the crystalline state. Copyright © 2015. Published by Elsevier B.V.

  2. The effects of unpaved roads on suspended sediment concentration of third- to fifth-order streams- A case study from southern Brazil (United States)

    Thomaz, E. L.; Vestena, L. R.; Ramos-Scharron, C. E.


    Unpaved roads have earned a reputation of inducing adverse effects on downstream water resources by increasing suspended sediment concentration because they typically generate sediment at rates up to several orders of magnitude above background and because they may enhance the efficiency of sediment delivery to fluvial networks. Although much research has been conducted on road effects in forested landscapes, proper understanding of their hydro-geomorphic role in rural areas is still desired. Unpaved roads are fundamental in the agricultural systems employed for the cultivation of maize and black beans on topographically-steep, marginal lands of southern Brazil. Marginal lands generate a sizeable fraction of the agricultural production in the state of Paraná, one of Brazil's agricultural powerhouses. This study documents the localized impacts on suspended sediment concentration of seven unpaved road crossings in the Guarabiroba River Catchment, Paraná, Brazil. A total of 156 suspended sediment samples were manually collected both upstream and downstream of road-crossings between 22-Apr-09 and 26-Apr-10 during 14 rainfall events ranging between 16 and 96 mm in total rainfall. The average length of road directly delivering runoff to each crossing varied from 0.56 - 2.4 km, and the size of the catchment areas of the third to fifth order monitored streams ranged from 0.3 to 13.5 km2. In addition to stream samples, 78 samples representing unpaved road runoff were collected during the same rain events. Upstream and downstream mean concentration values were compared for each storm at every site based on a paired t-test analysis (0.05% level). Mean suspended sediment concentration at stream segments located upstream of road crossings was 0.04 mg L-1 (s.d. = 0.05 mg L-1), while the mean downstream concentration was 0.11 mg L-1 (s.d. = 0.14 mg L-1) or 2.9 times higher than upstream samples. Meanwhile, road runoff had an average concentration of 0.93 mg L-1 (s.d. = 0.97 mg

  3. Method for analysis of psychopharmaceuticals in real industrial wastewater and groundwater with suspended organic particulate matter using solid phase extraction disks extraction and ultra-high performance liquid chromatography/time-of-flight mass spectrometry. (United States)

    Křesinová, Zdena; Linhartová, Lucie; Petrů, Klára; Krejčová, Lucie; Šrédlová, Kamila; Lhotský, Ondřej; Kameník, Zdeněk; Cajthaml, Tomáš


    A rapid and reliable analytical method was developed for the quantitative determination of psychopharmaceuticals, their precursors and by-products in real contaminated samples from a pharmaceutical company in Olomouc (Czech Republic), based on SPE disk extraction and detection by ultra performance liquid chromatography, combined with time-of-flight mass spectrometry. The target compounds were quantified in the real whole-water samples (water including suspended particles), both in the presence of suspended particulate matter (SPM) and high concentrations of other organic pollutants. A total of nine compounds were analyzed which consisted of three commonly used antidepressants (tricyclic antidepressants and antipsychotics), one antitussive agent and five by-products or precursors. At first, the SPE disk method was developed for the extraction of water samples (dissolved analytes, recovery 84-104%) and pressurised liquid extraction technique was verified for solid matrices (sludge samples, recovery 81-95%). In order to evaluate the SPE disk technique for whole water samples containing SPM, non contaminated groundwater samples were also loaded with different amounts (100 and 300mgL(-1)) of real contaminated sludge originating from the same locality. The recoveries from the whole-water samples obtained by SPE disk method ranged between 67 and 119% after the addition of the most contaminated sludge. The final method was applied to several real groundwater (whole-water) samples from the industrial area and high concentrations (up to 10(3)μgL(-1)) of the target compounds were detected. The results of this study document and indicate the feasibility of the SPE disk method for analysis of groundwater. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. Retrieval of Chlorophyll-a and Total Suspended Solids Using Iterative Stepwise Elimination Partial Least Squares (ISE-PLS Regression Based on Field Hyperspectral Measurements in Irrigation Ponds in Higashihiroshima, Japan

    Directory of Open Access Journals (Sweden)

    Zuomin Wang


    Full Text Available Concentrations of chlorophyll-a (Chl-a and total suspended solids (TSS are significant parameters used to assess water quality. The objective of this study is to establish a quantitative model for estimating the Chl-a and the TSS concentrations in irrigation ponds in Higashihiroshima, Japan, using field hyperspectral measurements and statistical analysis. Field experiments were conducted in six ponds and spectral readings for Chl-a and TSS were obtained from six field observations in 2014. For statistical approaches, we used two spectral indices, the ratio spectral index (RSI and the normalized difference spectral index (NDSI, and a partial least squares (PLS regression. The predictive abilities were compared using the coefficient of determination (R2, the root mean squared error of cross validation (RMSECV and the residual predictive deviation (RPD. Overall, iterative stepwise elimination based on PLS (ISE–PLS, using the first derivative reflectance (FDR, showed the best predictive accuracy, for both Chl-a (R2 = 0.98, RMSECV = 6.15, RPD = 7.44 and TSS (R2 = 0.97, RMSECV = 1.91, RPD = 6.64. The important wavebands for estimating Chl-a (16.97% of all wavebands and TSS (8.38% of all wavebands were selected by ISE–PLS from all 501 wavebands over the 400–900 nm range. These findings suggest that ISE–PLS based on field hyperspectral measurements can be used to estimate water Chl-a and TSS concentrations in irrigation ponds.

  5. Factors influencing storm-generated suspended-sediment concentrations and loads in four basins of contrasting land use, humid-tropical Puerto Rico (United States)

    Gellis, Allen C.


    The significant characteristics controlling the variability in storm-generated suspended-sediment loads and concentrations were analyzed for four basins of differing land use (forest, pasture, cropland, and urbanizing) in humid-tropical Puerto Rico. Statistical analysis involved stepwise regression on factor scores. The explanatory variables were attributes of flow, hydrograph peaks, and rainfall, categorized into 5 flow periods: (1) the current storm hydrograph, (2) the flow and rainfall since the previous storm event, (3) the previous storm event, (4) 2nd previous storm event, and (5) the 3rd previous storm event. The response variables (storm generated sediment loads and concentrations) were analyzed for three portions of the storm hydrograph: (1) the entire storm, (2) the rising limb, and (3) the recessional limb. Hysteresis differences in sediment concentration between the rising and falling limb were also analyzed using these explanatory variables.

  6. Application of chitosan as flocculant for coprecipitation of Mn(II) and suspended solids from dual-alkali FGD regenerating process. (United States)

    Wu, Zhong-Biao; Ni, Wei-Min; Guan, Bao-Hong


    Heavy metals and suspended solid (SS) needed to be removed from the recirculation of dual-alkali flue gas desulfurization (FGD) system. The feasibility of coprecipitation of heavy metal and SS by water-soluble chitosan was studied in a lab scale experiment. The association between chitosan and metal ions was verified through DSC and FT-IR. The pH investigation revealed that at the pH ranged from 5 to 9, there were three stages for different actions: adsorption of chitosan for Mn(II), precipitation of manganese hydroxide and coprecipitation of manganese hydroxide and chitosan-Mn(II) complex. The ion selectivity experiments showed that the occurrence of Ca(II) in the solution had little influence on the adsorption of chitosan for Mn(II). The decrease rate of adsorption capacity was about 0.0023 mmol g(-1) per 1 mg L(-1) Ca(II). When adsorption and flocculation of chitosan occurred at the same time and at the sufficient addition of chitosan, chitosan not only made solids flocculate but also enhanced sorption capacity of chitosan. Application of chitosan for coprecipitation of Mn(II) and SS could remove Mn(II) efficiently and improve the settling characteristics of SS from dual-alkali FGD regenerating process.

  7. Atomistic Simulations of Dislocations in a Model BCC Multicomponent Concentrated Solid Solution Alloy (Postprint) (United States)


    Dislocations ; Atomistic simulations; Concentrated multicomponent solid solution alloy; BCC crystal 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF...This has implications for higher-scale modeling ( dislocation dynamics or crystal plasticity) of HEA alloys, relative to elemental BCC metals, which...AFRL-RX-WP-JA-2017-0302 ATOMISTIC SIMULATIONS OF DISLOCATIONS IN A MODEL BCC MULTICOMPONENT CONCENTRATED SOLID SOLUTION ALLOY

  8. Rheology of dilute acid hydrolyzed corn stover at high solids concentration (United States)

    M.R. Ehrhardt; T.O. Monz; T.W. Root; R.K. Connelly; Tim Scott; D.J. Klingenberg


    The rheological properties of acid hydrolyzed corn stover at high solids concentration (20–35 wt.%) were investigated using torque rheometry. These materials are yield stress fluids whose rheological properties can be well represented by the Bingham model. Yield stresses increase with increasing solids concentration and decrease with increasing hydrolysis reaction...

  9. Review of total suspended particles (TSP) and PM2.5 concentration variations in Asia during the years of 1998-2015. (United States)

    Fang, Guor-Cheng; Zhuang, Yuan-Jie; Cho, Meng-Hsien; Huang, Chao-Yang; Xiao, You-Fu; Tsai, Kai-Hsiang


    In Asian countries such as China, Malaysia, Pakistan, India, Taiwan, Korea, Japan and Hong Kong, ambient air total suspended particulates and PM2.5 concentration data were collected and discussed during the years of 1998-2015 in this study. The aim of the present study was to (1) investigate and collect ambient air total suspended particulates (TSP) and PM2.5 concentrations for Asian countries during the past two decades. (2) Discuss, analyze and compare those particulates (TSP and PM2.5) annual concentration distribution trends among those Asian countries during the past two decades. (3) Test the mean concentration differences in TSP and PM2.5 among the Asian countries during the past decades. The results indicated that the mean TSP concentration order was shown as China > Malaysia > Pakistan > India > Taiwan > Korea > Japan. In addition, the mean PM2.5 concentration order was shown as Vietnam > India > China > Hong Kong > Mongolia > Korea > Taiwan > Japan and the average percentages of PM2.5 concentrations for Taiwan, China, Japan, Korea, Hong Kong, Mongolia and Other (India and Vietnam) were 8, 21, 6, 8, 14, 13 and 30%, respectively, during the past two decades. Moreover, t test results revealed that there were significant mean TSP and PM2.5 concentration differences for either China or India to any of the countries such as Taiwan, Korea and Japan in Asia during the past two decades for this study. Noteworthy, China and India are both occupied more than 60% of the TSP and PM2.5 particulates concentrations out of all the Asia countries. As for Taiwan, the average PM2.5 concentration displayed increasing trend in the years of 1998-1999. However, it showed decreasing trend in the years of 2000-2010. As for Korea, the average PM2.5 concentrations showed decreasing trend during the years of 2001-2013. Finally, the average PM2.5 concentrations for Mongolia displayed increasing trend in the years of 2004-2013.

  10. Evaluating Suspended Particles Concentration of the Inside and Outside Air of the Classroom and Its Influencing Factors in Middle schools and High Schools of Yazd

    Directory of Open Access Journals (Sweden)

    MH Ehrampoosh


    Full Text Available Abstract Introduction: Airborne pollution in such public environments as schools has adverse health effects on pupils and teachers who spend a noticeable amount of time in the school. Therefore, this study aimed to measure the suspended particles concentration of indoor and outdoor air of Yazd schools as well as to determine the influencing parameters on the pollution intensity. Methods: This analytical cross-sectional study was conducted in 20 middle-schools and high schools of males and females in winter of 2013. The environmental aerosol monitoring device, (HAZ-DUST EPAM5000 model was used to measure the concentration of PM1, PM2.5 and PM10. The study data were analyzed via applying correlation, simple linear regression and means comparison tests. Moreover, the study results were compared with the standards of World health organization(WHO and Environmental Health Organization(EPA. Results: The mean concentration of PM10, PM2.5 and PM1 in indoor class air was reported higher compared to the outdoor air. The indoor and outdoor air quality of schools in terms of Air Quality Index9 (AQI Calculator indicated an average condition for PM10, and an unhealthy condition for PM2.5 in regard with the vulnerable groups. A significant relationship was detected between indoor and outdoor air concentration particles (P<0.05. The mean indoor per outdoor air particles ratio (I/O was 1.68, 1.31, 1.46 respectively for PM10, PM2.5, PM1. Conclusion: The study findings revealed a significant relationship between indoor and outdoor suspended particle concentration demonstrating the particles penetration into the classrooms. Therefore, utilizing appropriate air conditioner systems are regarded effective in order to mitigate indoor class pollution.  

  11. Ambient Air Ammonia (NH3) Concentration in Two Solid Waste ...

    African Journals Online (AJOL)



    May 22, 2017 ... ABSTRACT. This work monitored the level of ammonia in the ambient air of two major solid waste dump sites in Abakaliki urban, Ebonyi State, in the morning for a period of a month on the onset of wet season, using portable monitor based on electrochemical sensor. The result showed that site 1 had a ...

  12. Confirmatory sediment analyses and solid and suspended particulate phase bioassays on sediment from Oakland Inner Harbor, San Francisco, California

    Energy Technology Data Exchange (ETDEWEB)

    Word, J.Q.; Ward, J.A.; Apts, C.W.; Woodruff, D.L.; Barrows, M.E.; Cullinan, V.I.; Hyland, J.L.; Campbell, J.F.


    The US Army Corps of Engineers (USACE), San Francisco District, was authorized by the US Congress to deepen the navigation channels of Inner and Outer Oakland Harbor, California. During review of the environmental impact statement required for this dredging and disposal project, a panel of national experts approved the open-water disposal of dredged sediment from selected areas within the Inner Harbor, subject to results of confirmatory solid phase bioassays. The San Francisco District of the Corps requested the Battle/Marine Sciences Laboratory (MSL) to conduct these confirmatory studies. The studies provided technical data for an evaluation of the potential environmental impact of this project. Within extremely narrow time constraints, these studies provided chemical and biological information required by ocean dumping regulations to determine suitability of the Oakland Inner Harbor and turning basin sediment for ocean disposal. 23 refs., 18 figs., 45 tabs.

  13. Comparison of fluvial suspended-sediment concentrations and particle-size distributions measured with in-stream laser diffraction and in physical samples (United States)

    Czuba, Jonathan A.; Straub, Timothy D.; Curran, Christopher A.; Landers, Mark N.; Domanski, Marian M.


    Laser-diffraction technology, recently adapted for in-stream measurement of fluvial suspended-sediment concentrations (SSCs) and particle-size distributions (PSDs), was tested with a streamlined (SL), isokinetic version of the Laser In-Situ Scattering and Transmissometry (LISST) for measuring volumetric SSCs and PSDs ranging from 1.8-415 µm in 32 log-spaced size classes. Measured SSCs and PSDs from the LISST-SL were compared to a suite of 22 datasets (262 samples in all) of concurrent suspended-sediment and streamflow measurements using a physical sampler and acoustic Doppler current profiler collected during 2010-12 at 16 U.S. Geological Survey streamflow-gaging stations in Illinois and Washington (basin areas: 38 – 69,264 km2). An unrealistically low computed effective density (mass SSC / volumetric SSC) of 1.24 g/ml (95% confidence interval: 1.05-1.45 g/ml) provided the best-fit value (R2 = 0.95; RMSE = 143 mg/L) for converting volumetric SSC to mass SSC for over 2 orders of magnitude of SSC (12-2,170 mg/L; covering a substantial range of SSC that can be measured by the LISST-SL) despite being substantially lower than the sediment particle density of 2.67 g/ml (range: 2.56-2.87 g/ml, 23 samples). The PSDs measured by the LISST-SL were in good agreement with those derived from physical samples over the LISST-SL's measureable size range. Technical and operational limitations of the LISST-SL are provided to facilitate the collection of more accurate data in the future. Additionally, the spatial and temporal variability of SSC and PSD measured by the LISST-SL is briefly described to motivate its potential for advancing our understanding of suspended-sediment transport by rivers.

  14. Measurement differences between turbidity instruments, and their implications for suspended sediment concentration and load calculations: A sensor inter-comparison study. (United States)

    Rymszewicz, A; O'Sullivan, J J; Bruen, M; Turner, J N; Lawler, D M; Conroy, E; Kelly-Quinn, M


    The use of turbidity for indicating environmentally detrimental levels of suspended and colloidal matter in freshwater systems, and for defining acceptable water quality standards in national and European drinking water regulations, is well established. Turbidity is therefore frequently adopted as a surrogate for suspended sediment concentrations (SSC), or as a relative and objective measure of water clarity in monitoring programmes. Through systematic, controlled experimentation, we tested the response of 12 commercially available turbidity sensors, of various designs, to gauge their measurement consistency when benchmarked against pre-prepared sediment suspensions of known SSC. Results showed that despite calibration to a Formazin standard, sensor responses to identical SSC solutions (in the range of 20-1000 mg L(-1)) varied considerably. For a given SSC, up to five-fold differences in recorded turbidity were recorded across the tested instruments. Furthermore, inconsistent measurements were identified across instruments, regardless of whether they operated using backscatter or side-scatter optical principles. While the findings may have implications for compliance with turbidity-based water quality standards, they are less likely to be an issue when turbidity is being used as a surrogate for SSC, provided that instrument use remains constant and that instrument drift is not an issue. In this study, a field comparison of a subset of four study sensors showed that despite very different absolute turbidity readings for a given SSC, well correlated and reliable turbidity - SSC ratings were established (as evidenced by r(2) coefficients from 0.92 to 0.98). This led to reasonably consistent suspended sediment load estimates of between 64.7 and 70.8 tonnes for a rainfall event analysed. This study highlights the potential for issues to arise when interpreting water turbidity datasets that are often assumed to be comparable, in that measurement inconsistency of the

  15. Correlations of turbidity to suspended-sediment concentration in the Toutle River Basin, near Mount St. Helens, Washington, 2010-11 (United States)

    Uhrich, Mark A.; Kolasinac, Jasna; Booth, Pamela L.; Fountain, Robert L.; Spicer, Kurt R.; Mosbrucker, Adam R.


    Researchers at the U.S. Geological Survey, Cascades Volcano Observatory, investigated alternative methods for the traditional sample-based sediment record procedure in determining suspended-sediment concentration (SSC) and discharge. One such sediment-surrogate technique was developed using turbidity and discharge to estimate SSC for two gaging stations in the Toutle River Basin near Mount St. Helens, Washington. To provide context for the study, methods for collecting sediment data and monitoring turbidity are discussed. Statistical methods used include the development of ordinary least squares regression models for each gaging station. Issues of time-related autocorrelation also are evaluated. Addition of lagged explanatory variables was used to account for autocorrelation in the turbidity, discharge, and SSC data. Final regression model equations and plots are presented for the two gaging stations. The regression models support near-real-time estimates of SSC and improved suspended-sediment discharge records by incorporating continuous instream turbidity. Future use of such models may potentially lower the costs of sediment monitoring by reducing time it takes to collect and process samples and to derive a sediment-discharge record.

  16. N-alkanes and polycyclic aromatic hydrocarbons in total suspended particulates from the southeastern Tibetan Plateau: concentrations, seasonal variations, and sources. (United States)

    Chen, Yang; Cao, Junji; Zhao, Jing; Xu, Hongmei; Arimoto, Richard; Wang, Gehui; Han, Yongming; Shen, Zhenxing; Li, Guohui


    Sixty-two suspended particle (TSP) samples were collected from Lulang on the southeastern Tibetan Plateau from July 2008 and July 2009 to investigate the concentrations, seasonal variations, and sources of n-alkanes and polycyclic aromatic hydrocarbons (PAHs). Samples were analyzed using thermal-deposition gas chromatography mass spectrometry. The concentrations of particulate total n-alkanes ranged from 0.10 to 21.83 ng m(-3), with an annual mean of 1.25 ng m(-3); the PAHs ranged from 0.06 to 2.53, with a mean of 0.59 ng m(-3). Up to 70% of PAHs were 5- and 6-ring compounds. The n-alkanes and PAHs both showed higher concentrations in winter and lower concentrations in summer. Analyses of diagnostic ratios indicate that 6.4% to 58.9% (mean 24.9%) of the n-alkanes were from plant waxes. Source characterization studies, i.e. diagnostic ratio and positive factor matrix analysis, suggest that the PAHs were from biomass burning as well as from fossil fuel combustion. Backward trajectory analysis suggests that the biomass mass burning pollutants could be from South Asia and western China via long distance transport. The study contributes to a more comprehensive understanding of the concentrations, seasonal variations, and sources of n-alkanes and PAHs in a remote background area in Tibetan Plateau. © 2013. Published by Elsevier B.V. All rights reserved.

  17. Macromodel for assessing residential concentrations of combustion-generated pollutants: Model development and preliminary predictions for CO, NO/sub 2/, and respirable suspended particles

    Energy Technology Data Exchange (ETDEWEB)

    Traynor, G.W.; Aceti, J.C.; Apte, M.G.; Smith, B.V.; Green, L.L.; Smith-Reiser, A.; Novak, K.M.; Moses, D.O.


    A simulation model (also called a ''macromodel'') has been developed to predict residential air pollutant concentration distributions for specified populations. The model inputs include the market penetration of pollution sources, pollution source characteristics (e.g., emission rates, source usage rates), building characteristics (e.g., house volume, air exchange rates), and meteorological parameters (e.g., outside temperature). Four geographically distinct regions of the US have been modeled using Monte Carlo and deterministic simulation techniques. Single-source simulations were also conducted. The highest predicted CO and NO/sub 2/ residential concentrations were associated with the winter-time use of unvented gas and kerosene space heaters. The highest predicted respirable suspended particulate concentrations were associated with indoor cigarette smoking and the winter-time use of non-airtight wood stoves, radiant kerosene heaters, convective unvented gas space heaters, and oil forced-air furnaces. Future field studies in this area should (1) fill information gaps identified in this report, and (2) collect information on the macromodel input parameters to properly interpret the results. It is almost more important to measure the parameters that affect indoor concentration than it is to measure the concentrations themselves.

  18. Effects of Humic Acid and Suspended Solids on the Removal of Heavy Metals from Water by Adsorption onto Granular Activated Carbon

    Directory of Open Access Journals (Sweden)

    Danious P. Sounthararajah


    Full Text Available Heavy metals constitute some of the most dangerous pollutants of water, as they are toxic to humans, animals, and aquatic organisms. These metals are considered to be of major public health concern and, therefore, need to be removed. Adsorption is a common physico-chemical process used to remove heavy metals. Dissolved organic carbon (DOC and suspended solids (SS are associated pollutants in water systems that can interact with heavy metals during the treatment process. The interactions of DOC and SS during the removal of heavy metals by granular activated carbon were investigated in batch and fixed-bed column experiments. Batch adsorption studies indicated that Langmuir adsorption maxima for Pb, Cu, Zn, Cd, and Ni at pH 6.5 were 11.9, 11.8, 3.3, 2.0, and 1.8 mg/g, respectively. With the addition of humic acid (HA (DOC representative, they were 7.5, 3.7, 3.2, 1.6, and 2.5 mg/g, respectively. In the column experiment, no breakthrough (complete removal was obtained for Pb and Cu, but adding HA provided a breakthrough in removing these metals. For Zn, Cd and Ni, this breakthrough occurred even without HA being added. Adding kaolinite (representative of SS had no effect on Pb and Cu, but it did on the other metals.

  19. Removal of Suspended Solids in Anaerobically Digested Slurries of Livestock and Poultry Manure by Coagulation Using Different Dosages of Polyaluminum Chloride (United States)

    Li, P.; Zhang, C. J.; Zhao, T. K.; Zhong, H.


    In this study, anaerobically digested slurries of livestock and poultry manure were pretreated by coagulation-sedimentation using an inorganic polymer coagulant, polyaluminum chloride (PAC). The effect of different PAC dosages on suspended solids (SS) removal and pH in the biogas slurries was assessed to provide reference values for reducing the organic load of biogas slurry in the coagulation-sedimentation process and explore the feasibility of reducing the difficulty in subsequent utilization or processing of biogas slurry. The results showed that for the pig slurry containing approximately 5000 mg/L SS, the removal rate of SS reached up to 81.6% with the coagulant dosage of 0.28 g/L PAC. For the chicken slurry containing approximately 2600 mg/L SS, the removal rate of SS was 30.2% with the coagulant dosage of 0.33 g/L PAC. The removal rate of SS in both slurries of livestock and poultry manure exhibited a downward trend with high PAC dosage. Therefore, there is a need to control the PAC dosage in practical use. The pH changed little in the two types of biogas slurries after treatment with different PAC dosages and both were in line with the standard values specified in the “Standards for Irrigation Water Quality”.

  20. Efficient performance and the microbial community changes of submerged anaerobic membrane bioreactor in treatment of sewage containing cellulose suspended solid at 25°C. (United States)

    Watanabe, Ryoya; Nie, Yulun; Takahashi, Shintaro; Wakahara, Shinichiro; Li, Yu-You


    Influence of cellulose as suspended solid (SS) on the performance of submerged anaerobic membrane bioreactor (SAnMBR) was evaluated at 25°C using two types of synthetic sewage (SS contained or not). During the 110days operation, COD and BOD removal, CH4 gas recovery and cellulose accumulation were investigated in detail. The influence of cellulose as SS in sewage on the SAnMBR performance was not significant at HRT longer than12h and 65-72% of the influent COD was recovered as methane gas at HRT of 12h. At HRT of 6h, the quality of effluent got worse and the accumulation of cellulose was found in reactor. 16S rRNA analysis revealed that the microbial diversity distribution including Archaea and Bacteria changed due to the addition of SS in sewage and specific microbe for cellulose degradation such as Proteobacteria was detected. Sludge in SAnMBR could acclimate to characteristics of sewage by self-adaptation. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Effect of mixed liquor volatile suspended solids (MLVSS and hydraulic retention time (HRT on the performance of activated sludge process during the biotreatment of real textile wastewater

    Directory of Open Access Journals (Sweden)

    Kapil Kumar


    Full Text Available Adequate information is available on colour and organics removal in batch mode using pure microbial cultures from dye contaminated wastewater. There was a need to develop environment friendly and cost effective treatment technique for actual field conditions. Therefore, the present study was undertaken with an aim to evaluate the potential of acclimatized mixed microbial consortia for the removal of colour and organics from real textile wastewater. Experiments were performed in laboratory scale activated sludge process (ASP unit under steady state condition, varying mixed liquor volatile suspended solids (MLVSS (2500, 3500 and 5000 mg/l and hydraulic retention time (HRT (18, 24 and 36 h. The results showed that decolourization and chemical oxygen demand (COD removal increased with increase in MLVSS and HRT. At 18 h HRT, decolourization was found to be 46, 54 and 67%, which increased to 67, 75 and 90% (36 h HRT at 2500, 3500 and 5000 mg/l MLVSS, respectively. COD removal was found to be 62, 73 and 77% (at 18 h HRT which increased to 77, 85 and 91% (36 h HRT at 2000, 3500 and 5000 mg/l MLVSS, respectively. On the basis of the results obtained in this study suitable treatment techniques can be developed for the treatment of wastewater contaminated with variety of dyes in continuous mode of operation. This shall have the advantage of treatment of larger quantity of wastewater in shorter duration.

  2. Suspended microfluidics


    Casavant, Benjamin P.; Berthier, Erwin; Theberge, Ashleigh B.; Jean BERTHIER; Montanez-Sauri, Sara I.; Bischel, Lauren L.; Brakke, Kenneth; Hedman, Curtis J.; Bushman, Wade; Keller, Nancy P.; Beebe, David J.


    Although the field of microfluidics has made significant progress in bringing new tools to address biological questions, the accessibility and adoption of microfluidics within the life sciences are still limited. Open microfluidic systems have the potential to lower the barriers to adoption, but the absence of robust design rules has hindered their use. Here, we present an open microfluidic platform, suspended microfluidics, that uses surface tension to fill and maintain a fluid in microscale...

  3. Solid Solution Effects on the Tensile Behaviour of Concentrated Mg-Zn Alloys (United States)

    Blake, A. H.; Cáceres, C. H.

    Solute in solution hardens the basal planes but causes solid solution softening on the prismatic (and possibly pyramidal) planes in dilute (slip systems still occurs. Therefore, solid solution effects on the strain hardening rate and ductility of cast polycrystalline Mg-Zn alloys, with Zn contents between 0 and 2.4 at.% have been studied. A constant grain size was obtained in all alloys by adding a small amount of Zr to the melt. The strain-hardening rate is low for dilute concentrations increasing monotonically above 1 at.% Zn. The ductility goes through a maximum at very low concentrations of Zn, decreasing for higher concentrations. This suggests that the solid solution hardening gradually offsets the solid solution softening effects at high concentrations of Zn.

  4. Impact of the spatial resolution of satellite remote sensing sensors in the quantification of total suspended sediment concentration: A case study in turbid waters of Northern Western Australia (United States)

    Fearns, Peter


    The impact of anthropogenic activities on coastal waters is a cause of concern because such activities add to the total suspended sediment (TSS) budget of the coastal waters, which have negative impacts on the coastal ecosystem. Satellite remote sensing provides a powerful tool in monitoring TSS concentration at high spatiotemporal resolution, but coastal managers should be mindful that the satellite-derived TSS concentrations are dependent on the satellite sensor’s radiometric properties, atmospheric correction approaches, the spatial resolution and the limitations of specific TSS algorithms. In this study, we investigated the impact of different spatial resolutions of satellite sensor on the quantification of TSS concentration in coastal waters of northern Western Australia. We quantified the TSS product derived from MODerate resolution Imaging Spectroradiometer (MODIS)-Aqua, Landsat-8 Operational Land Image (OLI), and WorldView-2 (WV2) at native spatial resolutions of 250 m, 30 m and 2 m respectively and coarser spatial resolution (resampled up to 5 km) to quantify the impact of spatial resolution on the derived TSS product in different turbidity conditions. The results from the study show that in the waters of high turbidity and high spatial variability, the high spatial resolution WV2 sensor reported TSS concentration as high as 160 mg L-1 while the low spatial resolution MODIS-Aqua reported a maximum TSS concentration of 23.6 mg L-1. Degrading the spatial resolution of each satellite sensor for highly spatially variable turbid waters led to variability in the TSS concentrations of 114.46%, 304.68% and 38.2% for WV2, Landsat-8 OLI and MODIS-Aqua respectively. The implications of this work are particularly relevant in the situation of compliance monitoring where operations may be required to restrict TSS concentrations to a pre-defined limit. PMID:28380059

  5. Impact of the spatial resolution of satellite remote sensing sensors in the quantification of total suspended sediment concentration: A case study in turbid waters of Northern Western Australia.

    Directory of Open Access Journals (Sweden)

    Passang Dorji

    Full Text Available The impact of anthropogenic activities on coastal waters is a cause of concern because such activities add to the total suspended sediment (TSS budget of the coastal waters, which have negative impacts on the coastal ecosystem. Satellite remote sensing provides a powerful tool in monitoring TSS concentration at high spatiotemporal resolution, but coastal managers should be mindful that the satellite-derived TSS concentrations are dependent on the satellite sensor's radiometric properties, atmospheric correction approaches, the spatial resolution and the limitations of specific TSS algorithms. In this study, we investigated the impact of different spatial resolutions of satellite sensor on the quantification of TSS concentration in coastal waters of northern Western Australia. We quantified the TSS product derived from MODerate resolution Imaging Spectroradiometer (MODIS-Aqua, Landsat-8 Operational Land Image (OLI, and WorldView-2 (WV2 at native spatial resolutions of 250 m, 30 m and 2 m respectively and coarser spatial resolution (resampled up to 5 km to quantify the impact of spatial resolution on the derived TSS product in different turbidity conditions. The results from the study show that in the waters of high turbidity and high spatial variability, the high spatial resolution WV2 sensor reported TSS concentration as high as 160 mg L-1 while the low spatial resolution MODIS-Aqua reported a maximum TSS concentration of 23.6 mg L-1. Degrading the spatial resolution of each satellite sensor for highly spatially variable turbid waters led to variability in the TSS concentrations of 114.46%, 304.68% and 38.2% for WV2, Landsat-8 OLI and MODIS-Aqua respectively. The implications of this work are particularly relevant in the situation of compliance monitoring where operations may be required to restrict TSS concentrations to a pre-defined limit.

  6. Impact of the spatial resolution of satellite remote sensing sensors in the quantification of total suspended sediment concentration: A case study in turbid waters of Northern Western Australia. (United States)

    Dorji, Passang; Fearns, Peter


    The impact of anthropogenic activities on coastal waters is a cause of concern because such activities add to the total suspended sediment (TSS) budget of the coastal waters, which have negative impacts on the coastal ecosystem. Satellite remote sensing provides a powerful tool in monitoring TSS concentration at high spatiotemporal resolution, but coastal managers should be mindful that the satellite-derived TSS concentrations are dependent on the satellite sensor's radiometric properties, atmospheric correction approaches, the spatial resolution and the limitations of specific TSS algorithms. In this study, we investigated the impact of different spatial resolutions of satellite sensor on the quantification of TSS concentration in coastal waters of northern Western Australia. We quantified the TSS product derived from MODerate resolution Imaging Spectroradiometer (MODIS)-Aqua, Landsat-8 Operational Land Image (OLI), and WorldView-2 (WV2) at native spatial resolutions of 250 m, 30 m and 2 m respectively and coarser spatial resolution (resampled up to 5 km) to quantify the impact of spatial resolution on the derived TSS product in different turbidity conditions. The results from the study show that in the waters of high turbidity and high spatial variability, the high spatial resolution WV2 sensor reported TSS concentration as high as 160 mg L-1 while the low spatial resolution MODIS-Aqua reported a maximum TSS concentration of 23.6 mg L-1. Degrading the spatial resolution of each satellite sensor for highly spatially variable turbid waters led to variability in the TSS concentrations of 114.46%, 304.68% and 38.2% for WV2, Landsat-8 OLI and MODIS-Aqua respectively. The implications of this work are particularly relevant in the situation of compliance monitoring where operations may be required to restrict TSS concentrations to a pre-defined limit.

  7. Dissolved-solids sources, loads, yields, and concentrations in streams of the conterminous United States (United States)

    Anning, David W.; Flynn, Marilyn E.


    Recent studies have shown that excessive dissolved-solids concentrations in water can have adverse effects on the environment and on agricultural, domestic, municipal, and industrial water users. Such effects motivated the U.S. Geological Survey’s National Water Quality Assessment Program to develop a SPAtially-Referenced Regression on Watershed Attributes (SPARROW) model that has improved the understanding of sources, loads, yields, and concentrations of dissolved solids in streams of the conterminous United States.

  8. MFT homogeneity study at TNX: Final report on the low weight percent solids concentration

    Energy Technology Data Exchange (ETDEWEB)

    Jenkins, W.J.


    A statistical design and analysis of both elemental analyses and weight percent solids analyses data was utilized to evaluate the MFT homogeneity at low heel levels and low agitator speed at both high and low solids feed concentrations. The homogeneity was also evaluated at both low and high agitator speed at the 6000+ gallons static level. The dynamic level portion of the test simulated feeding the Melter from the MFT to evaluate the uniformity of the solids slurry composition (Frit-PHA-Sludge) entering the melter from the MFT. This final report provides the results and conclusions from the second half of the study, the low weight percent solids concentration portion, as well as a comparison with the results from the first half of the study, the high weight percent solids portion.

  9. Filterability and Sludge Concentration in Membrane Bioreactors

    NARCIS (Netherlands)

    Lousada-Ferreira, M.


    The Thesis entitled “Filterability and Sludge Concentration in Membrane Bioreactors” aims at explaining the relation between Mixed Liquid Suspended Solids (MLSS) concentration, the amount of solids in the wastewater being treated, also designated as sludge, and filterability, being the ability of

  10. Suspended solids and total phosphorus loads and their spatial differences in a lake-rich river basin as determined by automatic monitoring network. (United States)

    Koskiaho, Jari; Tattari, Sirkka; Röman, Elina


    Turbidity datasets recorded by sensors during 2009-2012 were collected in five observation sites in the 2046-km2 Karjaanjoki River Basin in southern Finland. From these and water sample-based data, total phosphorus (TP) and total suspended solids (TSS) fluxes were determined. Based on calculations made with combined sensor- and water sample-based dataset, the annual loading from the Karjaanjoki Basin in 2009-2012 varied between 11,300 and 23,900[corrected] kg of TP and 3300-8400 t of TSS. As compared with two other river basins discharging into the Baltic Sea in southern Finland, the TP loading from Karjaanjoki was low because the summed retention in the two major lakes Hiidenvesi and Lohjanjärvi was high: 48 and 49% of the TSS and TP loadings generated in their upstream catchments, respectively. Depending on how water sampling took place in relation to peak flow events, differences of annual fluxes as determined by "water samples only" vs. "sensors and water samples" data varied between -22 and 26 for TP and -31 and 39% for TSS. This study proved automatic monitoring being useful when spatial differences and lake retention of riverine fluxes are explored. Moreover, the loading estimates calculated on the base of well-functioning and well-maintained automatic monitoring system, supported with water sampling during periods when devices were off, are undoubtedly more accurate than those based on manual grab water sampling only. The findings of this study were in line with, and well contribute to, earlier Finnish and international research on automatic water quality monitoring.

  11. Quantum Critical Behavior in a Concentrated Ternary Solid Solution. (United States)

    Sales, Brian C; Jin, Ke; Bei, Hongbin; Stocks, G Malcolm; Samolyuk, German D; May, Andrew F; McGuire, Michael A


    The face centered cubic (fcc) alloy NiCoCrx with x ≈ 1 is found to be close to the Cr concentration where the ferromagnetic transition temperature, Tc, goes to 0. Near this composition these alloys exhibit a resistivity linear in temperature to 2 K, a linear magnetoresistance, an excess -TlnT (or power law) contribution to the low temperature heat capacity, and excess low temperature entropy. All of the low temperature electrical, magnetic and thermodynamic properties of the alloys with compositions near x ≈ 1 are not typical of a Fermi liquid and suggest strong magnetic fluctuations associated with a quantum critical region. The limit of extreme chemical disorder in this simple fcc material thus provides a novel and unique platform to study quantum critical behavior in a highly tunable system.

  12. Effect of solids concentration on removal of heavy metals from mine tailings via bioleaching. (United States)

    Liu, Yun-Guo; Zhou, Ming; Zeng, Guang-Ming; Li, Xin; Xu, Wei-Hua; Fan, Ting


    Mining of mineral ore and disposal of resulting waste tailings pose a significant risk to the surrounding environment. The objective of this work is to demonstrate the feasibility to remove heavy metals from mine tailings with the use of bioleaching and meanwhile to investigate the effect of solids concentration on removal of heavy metals from mine tailings by indigenous sulfur-oxidizing bacteria and the transformation of heavy metal forms after the bioleaching process. This work showed the laboratory results of bioleaching experiments on Pb-Zn-Cu mine tailings. The results showed that 98.08% Zn, 96.44% Cu, and 43.52% Pb could be removed from mine tailings by the bioleaching experiment after 13 days at 1% (w/v) solids concentration and the rates of pH reduction, ORP rise and sulfate production were reduced with the increase of solids concentration, due to the buffering capacity of mine tailing solids. The results also indicated that solid concentration 1% was found to be best to bacterial activity and metal solubilization of the five solids concentration tested (1%, 2%, 5%, 8% and 10%) under the chosen experimental conditions. In addition, the bioleaching had a significant impact on changes in partitioning of heavy metals.

  13. Starch industry wastewater for production of biopesticides--ramifications of solids concentrations. (United States)

    Vu, Khanh Dang; Tyagi, R D; Brar, S K; Valéro, J R; Surampalli, R Y


    Total solids (TS) concentrations ranging from 15 to 66 g L(-1) of starch industry wastewater (SIW) were tested as raw material for the production of Bacillus thuringiensis var. kurstaki HD-1 (Btk) biopesticide in shake flasks and a 15 L bench-scale fermenter. Shake flask studies revealed a higher delta-endotoxin concentration of Btk at 30 g L(-1) TS concentration and 2.5% (v v(-1)) volume of pre-culture. The fermenter experiments conducted using SIW at 30 g L(-1) TS concentration under controlled conditions of temperature, pH and dissolved oxygen showed higher spore count, enzyme production (protease and amylase) and delta-endotoxin concentration as compared with those of SIW at 15 g L(-1) TS concentration. The entomotoxicity, at the end of fermentation, with SIW at 30 g L(-1) solids concentration (17.8 x 10(9) SBU L(-1), measured against spruce budworm) was considerably higher as compared with entomotoxicity at 15 g L(-1) solids concentration (15.3 x 10(9) SBU L(-1)) and semi-synthetic medium (11.7 x 10(9) SBU L(-1)). The pellet, comprising spores and delta-endotoxin complex obtained after centrifugation and followed by resuspension (in supernatant) in one-tenth of the original volume, of SIW at 30 g L(-1) solids concentration media registered the highest potential for application (to protect forests against spruce budworm) than other media in term of entomotoxicity.

  14. Impact of sampling frequency on mean concentrations and estimated loads of suspended sediment in a Norwegian river: implications for water management. (United States)

    Skarbøvik, Eva; Stålnacke, Per; Bogen, Jim; Bønsnes, Truls E


    Reliable estimates of mean concentrations and loads of pollutants in rivers have become increasingly important for management purposes, particularly with the implementation of the European Union Water Framework Directive (WFD). Here, the Numedalslågen River (5500 km(2)) in southern Norway was used as a case study to evaluate the effects of sampling frequency on mean concentrations and estimated loads of suspended particulate matter (SPM). Daily monitoring data from five seasons (April/June-October/November 2001-2005) were analyzed, and three different load estimation techniques were tested: rating curves, linear interpolation, and the ratio method. The reliability of mean SPM concentrations improved with increasing sampling frequency, but even weekly sampling gave error rates as high as 70% in seasons with elevated sediment loads. Load estimates varied considerably depending on both the sampling frequency and the calculation method used. None of the methods provided consistently good results, but the lowest error rate was achieved when using the rating curve on data from fortnightly sampling and additional sampling during floods. Sampling at monthly intervals gave the highest error rates and cannot be recommended for any of the calculation methods applied here. SPM concentrations were correlated (r(2)>0.5) with arsenic, lead, nickel, orthophosphate, and total phosphorus in the Numedalslågen River. Therefore, the current findings may also have implications for substances other than SPM. The discussion considers examples from actual use of infrequently collected data, and it is advised that managers account for uncertainties in both concentration means and load estimates when assessing the state of a water body or planning mitigation measures. Copyright © 2012 Elsevier B.V. All rights reserved.

  15. Retrieval of total suspended matter (TSM) and chlorophyll-a (Chl-a) concentration from remote-sensing data for drinking water resources. (United States)

    Song, Kaishan; Li, Lin; Wang, Zongming; Liu, Dianwei; Zhang, Bai; Xu, Jingping; Du, Jia; Li, Linhai; Li, Shuai; Wang, Yuandong


    The concentrations of chlorophyll-a (Chl-a) and total suspended matter (TSM) are major water quality parameters that can be retrieved using remotely sensed data. Water sampling works were conducted on 15 July 2007 and 13 September 2008 concurrent with the Indian Remote-Sensing Satellite (IRS-P6) overpass of the Shitoukoumen Reservoir. Both empirical regression and back-propagation artificial neural network (ANN) models were established to estimate Chl-a and TSM concentration with both in situ and satellite-received radiances signals. It was found that empirical models performed well on the TSM concentration estimation with better accuracy (R (2) = 0.94, 0.91) than their performance on Chl-a concentration (R (2) = 0.62, 0.75) with IRS-P6 imagery data, and the models accuracy marginally improved with in situ spectra data. Our results indicated that the ANN model performed better for both Chl-a (R (2) = 0.91, 0.82) and TSM (R (2) = 0.98, 0.94) concentration estimation through in situ collected spectra; the same trend followed for IRS-P6 imagery data (R (2) = 0.75 and 0.90 for Chl-a; R (2) = 0.97 and 0.95 for TSM). The relative root mean square errors (RMSEs) from the empirical model for TSM (Chl-a) were less than 15% (respectively 27.2%) with both in situ and IRS-P6 imagery data, while the RMSEs were less than 7.5% (respectively 18.4%) from the ANN model. Future work still needs to be undertaken to derive the dynamic characteristic of Shitoukoumen Reservoir water quality with remotely sensed IRS-P6 or Landsat-TM data. The algorithms developed in this study will also need to be tested and refined with more imagery data acquisitions combined with in situ spectra data.

  16. Optimization of biological phosphorus and ammonia removal in a combined fixed and suspended growth wastewater treatment system: Final report

    Energy Technology Data Exchange (ETDEWEB)



    This project was conducted to optimize design and operational criteria for enhanced biological phosphorus removal and nitrification of ammonia in the fixed growth reactor-suspended growth reactor (FGR-SGR) process. The research completed the investigation of optimum hydraulic retention times for biological phosphorus removal in both the unaerated and aerated phases of the suspended growth components of the FGR-SGR system, including an assessment of the possibility of reducing suspended growth aeration requirements by using oxidized forms of nitrogen rather than dissolved oxygen for biological phosphorus uptake; investigated the effects on biological phosphorus removal and nitrification of varying the internal recycle flow rates; and investigated the optimum solids retention time, or the optimum operating mixed liquor suspended solids concentration, in the suspended growth component of the system for biological phosphorus removal and nitrification-denitrification.

  17. Particulate matter chemical component concentrations and sources in settings of household solid fuel use. (United States)

    Secrest, M H; Schauer, J J; Carter, E M; Baumgartner, J


    Particulate matter (PM) air pollution derives from combustion and non-combustion sources and consists of various chemical species that may differentially impact human health and climate. Previous reviews of PM chemical component concentrations and sources focus on high-income urban settings, which likely differ from the low- and middle-income settings where solid fuel (ie, coal, biomass) is commonly burned for cooking and heating. We aimed to summarize the concentrations of PM chemical components and their contributing sources in settings where solid fuel is burned. We searched the literature for studies that reported PM component concentrations from homes, personal exposures, and direct stove emissions under uncontrolled, real-world conditions. We calculated weighted mean daily concentrations for select PM components and compared sources of PM determined by source apportionment. Our search criteria yielded 48 studies conducted in 12 countries. Weighted mean daily cooking area concentrations of elemental carbon, organic carbon, and benzo(a)pyrene were 18.8 μg m-3 , 74.0 μg m-3 , and 155 ng m-3 , respectively. Solid fuel combustion explained 29%-48% of principal component/factor analysis variance and 41%-87% of PM mass determined by positive matrix factorization. Multiple indoor and outdoor sources impacted PM concentrations and composition in these settings, including solid fuel burning, mobile emissions, dust, and solid waste burning. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  18. Bench-Scale and Pilot-Scale Treatment Technologies for the Removal of Total Dissolved Solids from Coal Mine Water: A Review (United States)

    Coal mine water (CMW) is typically treated to remove suspended solids, acidity, and soluble metals, but high concentrations of total dissolved solids (TDS) have been reported to impact the environment at several CMW discharge points. Consequently, various states have establishe...

  19. A Semi-Analytic Model for Estimating Total Suspended Sediment Concentration in Turbid Coastal Waters of Northern Western Australia Using MODIS-Aqua 250 m Data

    Directory of Open Access Journals (Sweden)

    Passang Dorji


    Full Text Available Knowledge of the concentration of total suspended sediment (TSS in coastal waters is of significance to marine environmental monitoring agencies to determine the turbidity of water that serve as a proxy to estimate the availability of light at depth for benthic habitats. TSS models applicable to data collected by satellite sensors can be used to determine TSS with reasonable accuracy and of adequate spatial and temporal resolution to be of use for coastal water quality monitoring. Thus, a study is presented here where we develop a semi-analytic sediment model (SASM applicable to any sensor with red and near infrared (NIR bands. The calibration and validation of the SASM using bootstrap and cross-validation methods showed that the SASM applied to Moderate Resolution Imaging Spectroradiometer (MODIS-Aqua band 1 data retrieved TSS with a root mean square error (RMSE and mean averaged relative error (MARE of 5.75 mg/L and 33.33% respectively. The application of the SASM over our study region using MODIS-Aqua band 1 data showed that the SASM can be used to monitor the on-going, post and pre-dredging activities and identify daily TSS anomalies that are caused by natural and anthropogenic processes in coastal waters of northern Western Australia.

  20. Chemical composition shape form and size of suspended solids in the atmosphere carried by rain water; Composicion quimica, forma y tamano de solidos suspendidos en la atmosfera acarreados por el agua de lluvia

    Energy Technology Data Exchange (ETDEWEB)

    Iturbe G, J.L.; Lopez M, B.E.; Torre O, J. De la [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)


    The interest of this work is to know about shape form, size and chemical composition of the suspended solids in the atmosphere of Toluca city and which are carried by the rains. The harvest of the samples was carried out during january to november 1999. The separation of the particulate matter from the rain water was realized through centrifugation. The solids were analysed by Scanning Electron Microscopy to know the shape form and size and the chemical composition was determined by X-ray dispersive energy in general form and of some particles individually analysed. The p H was measured to the solutions and the quantification of some dissolved ions by the Icp technique was realized. The results of the solids showed C, O, Na, Mg, Al, Si, S, P, K, Ca, Ti and Fe. Moreover they present sizes which varying from a ten of nanometers until some tens of microns. (Author)

  1. Application of dimensionless sediment rating curves to predict suspended-sediment concentrations, bedload, and annual sediment loads for rivers in Minnesota (United States)

    Ellison, Christopher A.; Groten, Joel T.; Lorenz, David L.; Koller, Karl S.


    Consistent and reliable sediment data are needed by Federal, State, and local government agencies responsible for monitoring water quality, planning river restoration, quantifying sediment budgets, and evaluating the effectiveness of sediment reduction strategies. Heightened concerns about excessive sediment in rivers and the challenge to reduce costs and eliminate data gaps has guided Federal and State interests in pursuing alternative methods for measuring suspended and bedload sediment. Simple and dependable data collection and estimation techniques are needed to generate hydraulic and water-quality information for areas where data are unavailable or difficult to collect.The U.S. Geological Survey, in cooperation with the Minnesota Pollution Control Agency and the Minnesota Department of Natural Resources, completed a study to evaluate the use of dimensionless sediment rating curves (DSRCs) to accurately predict suspended-sediment concentrations (SSCs), bedload, and annual sediment loads for selected rivers and streams in Minnesota based on data collected during 2007 through 2013. This study included the application of DSRC models developed for a small group of streams located in the San Juan River Basin near Pagosa Springs in southwestern Colorado to rivers in Minnesota. Regionally based DSRC models for Minnesota also were developed and compared to DSRC models from Pagosa Springs, Colorado, to evaluate which model provided more accurate predictions of SSCs and bedload in Minnesota.Multiple measures of goodness-of-fit were developed to assess the effectiveness of DSRC models in predicting SSC and bedload for rivers in Minnesota. More than 600 dimensionless ratio values of SSC, bedload, and streamflow were evaluated and delineated according to Pfankuch stream stability categories of “good/fair” and “poor” to develop four Minnesota-based DSRC models. The basis for Pagosa Springs and Minnesota DSRC model effectiveness was founded on measures of goodness

  2. Nonisothermal nucleation in a solid solution of CuCl in glass: Concentration effect upon heating of the solid solution (United States)

    Leiman, V. I.; Ashkalunin, A. L.; Derkacheva, O. Yu.; Maksimov, V. M.


    The influence of the heating rate of a solid solution of CuCl in glass on the size distribution of the produced CuCl nanoparticles is studied. The distribution curves of CuCl nanocrystals are determined by the method of exciton-thermal analysis. It is established that the concentration of CuCl nanoparticles increases by ten times upon slowing the sample heating process from 2 to 60 min, while the mean radius of particles decreases almost twice. The concentration of CuCl nanoparticles passes through a maximum in the process of heating the sample. The numerical simulation of the nucleation upon slow heating of a solid solution showed that the formation of the concentration maximum of the new phase clusters is determined by a rapid increase in the critical radius owing to an increase in temperature and decrease in the solution supersaturation. As a result, the formation of new phase nuclei ceases at a certain temperature, and a part of the previously formed clusters dissolves.

  3. Simulation of streamflow and suspended-sediment concentrations and loads in the lower Nueces River watershed, downstream from Lake Corpus Christi to the Nueces Estuary, South Texas, 1958-2008 (United States)

    Ockerman, Darwin J.; Heitmuller, Franklin T.


    The U.S. Geological Survey (USGS), in cooperation with the U.S. Army Corps of Engineers-Fort Worth District, City of Corpus Christi, Guadalupe-Blanco River Authority, San Antonio River Authority, and San Antonio Water System, developed, calibrated, and tested a Hydrological Simulation Program ? FORTRAN (HSPF) watershed model to simulate streamflow and suspended-sediment concentrations and loads during 1958-2008 in the lower Nueces River watershed, downstream from Lake Corpus Christi to the Nueces Estuary in South Texas. Data available to simulate suspended-sediment concentrations and loads consisted of historical sediment data collected during 1942-82 in the study area and suspended-sediment concentration data collected periodically by the USGS during 2006-07 at three USGS streamflow-gaging stations, Nueces River near Mathis, Nueces River at Bluntzer, and Nueces River at Calallen. The Nueces River near Mathis station is downstream from Wesley E. Seale Dam, completed in 1958 to impound Lake Corpus Christi. Suspended-sediment data collected before and after completion of Wesley E. Seale Dam provide insights to the effects of the dam and reservoir on suspended-sediment loads transported by the lower Nueces River from downstream of the dam to the Nueces Estuary. Annual suspended-sediment loads at a site near the Nueces River at Mathis station were considerably lower, for a given annual mean discharge, after the dam was completed than before the dam was completed. Most of the suspended sediment transported by the Nueces River downstream from Wesley E. Seale Dam occurred during high-flow releases from the dam or during floods. During October 1964-September 1971, about 532,000 tons of suspended sediment were transported by the Nueces River near Mathis. Of this amount, about 473,000 tons, or about 89 percent, were transported by large runoff events (mean streamflow exceeding 1,000 cubic feet per second). To develop the watershed model to simulate suspended

  4. Estimating Production and Consumption of Solid Reactive Fe Phases in Marine Sediments from Concentration Profiles (United States)

    Devereux, R.; Lettmann, K.; Lehrter, J. C.; Beddick, D. L., Jr.; Yates, D. F.; Hoglund, M.; Rogers, J. E.; Jarvis, B.


    1D diffusion models may be used to estimate rates of production and consumption of dissolved metabolites in marine sediments but are applied less often to the solid phase. Here we used a numerical inverse method assuming steady state conditions to estimate solid phase Fe(III) and Fe(II) consumption and production rates, respectively, from sediment concentration profiles. First, porewater concentration profiles of dissolved inorganic carbon (DIC) and ammonium (NH4+) in muddy northern Gulf of Mexico sediments were analyzed by the model. The runs were used to fit model concentration outputs to sediment sample data, identify zones of production and consumption, and obtain modeled fluxes across the sediment-water interface that best matched experimentally-obtained flux rates. Modeled fluxes were sensitive to coefficients of sediment irrigation and bioturbation in addition to boundary concentrations. Assuming diffusion coefficients = 0 for solid phase minerals, drivers for estimating production and consumption rates from solid phase concentrations are then the rates of sedimentation and porewater advection, and coefficients of bioturbation and irrigation. Thus, applying the model with sediment irrigation and bioturbation terms obtained in the DIC and NH4+ runs, and replacing values of porosity with 1-porosity, rates of Fe(II) production closely matched rates of Fe(III) consumption at about 10-3 nmole cm-1 sec-1. High modeled Fe transformations occurred in the upper 3.5 cm of sediment. In addition, porewater Fe2+ and dissolved Mn concentration profiles both yielded modeled production in the top 0.5 cm of sediment with consumption below that suggesting a zone of precipitation as sulfide or carbonate minerals. These results demonstrate that simple 1D models can be applied to the solid phase of marine sediments and may additionally be helpful in estimating coefficients of sediment irrigation and bioturbation.

  5. Electronic energy migration in solid versus liquid host matrices for concentrated perylenediimide dye solutions. (United States)

    Colby, Kathryn A; Bardeen, Christopher J


    In this paper, we continue our evaluation of Forster-type theories of exciton diffusion in disordered environments. The perylenediimide dye Lumogen Red is used as a donor molecule in two different liquids, CHCl(3) and dimethylformamide, and the energy transfer to the acceptor molecule Rhodamine 700 is measured using time-resolved fluorescence decays. The exciton motion is measured over Lumogen Red concentrations ranging from 1 × 10(-4) to 5 × 10(-2) M, and the results are compared to previous results for exciton diffusion in a solid polymer. Depending on the theoretical approach used to analyze the data, we find that the energy migration in the liquids is a factor of 2-3 faster than in the solid polymer, even after taking molecular translation into account. Measurements for a Lumogen Red concentration of 10 mM in the different host environments yield diffusion constants ranging from 2.2 to 3.1 nm(2)/ns in the liquids, as compared to 1.1-1.2 nm(2)/ns in solid poly(methyl methacrylate) (PMMA). The results in the liquids are in good agreement with theoretical predictions and numerical simulations of previous workers, while the results in solid PMMA are 2-3 times slower. This discrepancy is discussed in the context of the rapid energetic averaging present in the liquid environments but absent in the solid matrix, where unfavorable configurations and low energy trapping sites are frozen in by the static disorder.

  6. Long-term effects of clear-cutting and site preparation on carbon, nitrogen, phosphorus and suspended solids export to boreal first order streams (United States)

    Palviainen, Marjo; Finér, Leena; Laurén, Ari; Launiainen, Samuli; Piirainen, Sirpa; Mattsson, Tuija; Starr, Mike


    Clear-cutting has been observed to generally increase leaching and element exports to adjacent watercourses. Most studies on the effects of clear-cutting on nutrient export in north European boreal forests have been short-term and were carried out in the 1970s and 1980s when forestry practices were different from those of today. Nowadays clear-cut areas are smaller, soil preparation methods are lighter (less soil disturbance), and buffer zones are left along watercourses. Several hundred thousand hectares of forests are clear-cut and soils are scarified before regeneration operations in Fennoscandia, but little is known of the long-term impacts of the current methods on the surface water quality. We studied the long-term (14 years) effects of clear-cutting and site preparation on runoff (mm) and the export of total nitrogen (total N), total organic nitrogen (TON), ammonium (NH4-N), nitrate (NO3-N), total phosphorus (total P), phosphate (PO4-P), total organic carbon (TOC) and suspended solids (SS) in two paired-catchments in Eastern Finland. In accordance with current forest management guidelines, clear cutting (stem-only removal) were carried out on 34% (C34) and 12% (C12) of the area of the treated catchments, scarification carried out after 2 years and planting with Scots pine seedlings after 3 years. Buffer zones were left between the clear-cut areas and the catchment outlet stream. In the case of the C34 catchment, clear-cutting increased annual runoff and exports of total N, TON, NO3-N, PO4-P and SS. Annual runoff increased by 4 - 102 mm (1-30%). The annual exports of total N, TON, NO3-N, PO4-P and SS increased by at most 0.36 (72%), 0.35 (76%), 0.15 (1056%), 0.002 (35%) and 2.0 (715%) kg/ha, respectively. For the C12 catchment, annual runoff did not change and only exports of PO4-P and SS increased. Annual export of PO4-P increased by at maximum 0.007 kg/ha (69%) and that of SS by at maximum 0.55 kg/ha (271%). Clear-cutting induced increases in runoff and

  7. Sorption of Arsenic from Desalination Concentrate onto Drinking Water Treatment Solids: Operating Conditions and Kinetics

    Directory of Open Access Journals (Sweden)

    Xuesong Xu


    Full Text Available Selective removal of arsenic from aqueous solutions with high salinity is required for safe disposal of the concentrate and protection of the environment. The use of drinking water treatment solids (DWTS to remove arsenic from reverse osmosis (RO concentrate was studied by batch sorption experiments. The impacts of solution chemistry, contact time, sorbent dosage, and arsenic concentration on sorption were investigated, and arsenic sorption kinetics and isotherms were modeled. The results indicated that DWTS were effective in removing arsenic from RO concentrate. The arsenic sorption process followed a pseudo-second-order kinetic model. Multilayer adsorption was simulated by Freundlich equation. The maximum sorption capacities were calculated to be 170 mg arsenic per gram of DWTS. Arsenic sorption was enhanced by surface precipitation onto the DWTS due to the high amount of calcium in the RO concentrate and the formation of ternary complexes between arsenic and natural organic matter (NOM bound by the polyvalent cations in DWTS. The interactions between arsenic and NOM in the solid phase and aqueous phase exhibited two-sided effects on arsenic sorption onto DWTS. NOM in aqueous solution hindered the arsenic sorption onto DWTS, while the high organic matter content in solid DWTS phase enhanced arsenic sorption.


    Sidman, Richard L.


    Fragments of freshly obtained retinas of several vertebrate species were studied by refractometry, with reference to the structure of the rods and cones. The findings allowed a reassessment of previous descriptions based mainly on fixed material. The refractometric method was used also to measure the refractice indices and to calculate the concentrations of solids and water in the various cell segments. The main quantitative data were confirmed by interference microscopy. When examined by the method of refractometry the outer segments of freshly prepared retinal rods appear homogeneous. Within a few minutes a single eccentric longitudinal fiber appears, and transverse striations may develop. These changes are attributed to imbibition of water and swelling in structures normally too small for detection by light microscopy. The central "core" of outer segments and the chromophobic disc between outer and inner segments appear to be artifacts resulting from shrinkage during dehydration. The fresh outer segments of cones, and the inner segments of rods and cones also are described and illustrated. The volumes, refractive indices, concentrations of solids, and wet and dry weights of various segments of the photoreceptor cells were tabulated. Rod outer segments of the different species vary more than 100-fold in volume and mass but all have concentrations of solids of 40 to 43 per cent. Cone outer segments contain only about 30 per cent solids. The myoids, paraboloids, and ellipsoids of the inner segments likewise have characteristic refractive indices and concentrations of solids. Some of the limitations and particular virtues of refractometry as a method for quantitative analysis of living cells are discussed in comparison with more conventional biochemical techniques. Also the shapes and refractive indices of the various segments of photoreceptor cells are considered in relation to the absorption and transmission of light. The Stiles-Crawford effect can be accounted

  9. Remoção de sólidos suspensos e totais em biofiltros operando com esgoto doméstico primário para reuso na agricultura Removal of suspended and total solids in biofilters operating with primary domestic sewage for reuse in agriculture

    Directory of Open Access Journals (Sweden)

    Rafael Oliveira Batista


    Full Text Available Este trabalho objetivou analisar a remoção de sólidos suspensos e totais em biofiltros, preenchidos com lixo compostado, bagaço de cana-de-açúcar e serragem de madeira, submetidos às taxas de aplicação do esgoto doméstico de 0,5, 1,0 e 1,5 m³ m-2 d-1, em Viçosa-MG. Para isso, foi montada uma bancada experimental, constituída de 27 biofiltros, em área experimental da Universidade Federal de Viçosa. As concentrações de sólidos suspensos e totais foram determinadas, mensalmente, durante período de 153 dias. O experimento foi montado no esquema de parcelas subsubdivididas, tendo, nas parcelas, as taxas de aplicação do esgoto doméstico; nas subparcelas, os tipos de material orgânico e, nas subsubparcelas, os períodos de avaliação, no delineamento em blocos casualizados, com três repetições. Os resultados indicaram que os biofiltros proporcionaram remoções de sólidos suspensos e totais de até 82 e 46%, no esgoto doméstico, após 153 dias de operação; a serragem de madeira foi o tipo de material orgânico filtrante com melhor desempenho no tratamento de esgoto doméstico; as aplicações de taxas de 0,5, 1,0 e 1,5 m³ m-2 d-1 de esgoto não apresentaram diferenças quanto à remoção de sólidos suspensos e totais; e a utilização de biofiltros minimiza a obstrução de emissores causada por sólidos suspensos, quando do aproveitamento agrícola de esgoto doméstico, por via do sistema de irrigação por gotejamento.This study aimed to evaluate the removal of suspended and total solids in biofilters filled with composted waste, sugar cane bagasse and sawdust submitted to the application rates of domestic sewage of 0.5, 1.0 and 1.5 m³ m-2 d-1 in Viçosa-MG. An experimental test unit was set up in experimental area of the Federal University of Viçosa. The concentrations of suspended and total solids were determined monthly during a period of 153 days. The experiment was arranged in a split split plot design, with

  10. Analytical determination of Chemical Oxygen Demand in samples considered to be difficult to analyse: solid substrates and liquid samples with high suspended solid concentrations

    DEFF Research Database (Denmark)

    Raposo, Francisco; Fernández-Cegrí, V.; De la Rubia, M.A.

    Chemical oxygen demand (COD) is a critical analytical parameter in the field of waste and wastewater treatment processes, and more specifically in anaerobic digestion processes. However, little is known about the COD measurement quality of anaerobic digestion samples. Taking into account the lack...

  11. Kinetics of mesophilic anaerobic digestion of the organic fraction of municipal solid waste: Influence of initial total solid concentration. (United States)

    Fernández, J; Pérez, M; Romero, L I


    The anaerobic mesophilic degradation of municipal waste has been studied in discontinuous lab-reactors with two different initial concentrations of OFMSW: R20, with 931.1mg DOC/L (20% TS), and R30, with 1423.4 mg DOC/L (30% TS). The anaerobic digestion process was favoured when it was carried on material with a total solids content of 20% in comparison to a similar process with 30% TS. A higher level of organic matter, in terms of DOC and VFA, 18.18% and 8.09% respect, was removed in the system with the lower amount of solids. The kinetics parameters showed higher active biomass and a higher coefficient for the production of methane at the lower loading. The highest maximum specific growth rate for the microorganisms (mu(MAX)) in the reactors with 20% TS, a value of 0.192 d(-1), was achieved in comparison to 0.131 d(-1) in the reactors with 30% TS. The inverse of the F:M ratio was higher in the R20 system with a value of 0.0104 (cf. 0.0006 in R30) and, as a result, the R30 system required longer hydrolytic and acidogenic stages. X(V0)/Y(X/S) and the yield coefficient for product generation (alpha(P/S)) were higher, by around 53%, for the R20 digester. Copyright 2010 Elsevier Ltd. All rights reserved.

  12. Relations between continuous real-time turbidity data and discrete suspended-sediment concentration samples in the Neosho and Cottonwood Rivers, east-central Kansas, 2009-2012 (United States)

    Foster, Guy M.


    The Neosho River and its primary tributary, the Cottonwood River, are the primary sources of inflow to the John Redmond Reservoir in east-central Kansas. Sedimentation rate in the John Redmond Reservoir was estimated as 743 acre-feet per year for 1964–2006. This estimated sedimentation rate is more than 80 percent larger than the projected design sedimentation rate of 404 acre-feet per year, and resulted in a loss of 40 percent of the conservation pool since its construction in 1964. To reduce sediment input into the reservoir, the Kansas Water Office implemented stream bank stabilization techniques along an 8.3 mile reach of the Neosho River during 2010 through 2011. The U.S. Geological Survey, in cooperation with the Kansas Water Office and funded in part through the Kansas State Water Plan Fund, operated continuous real-time water-quality monitors upstream and downstream from stream bank stabilization efforts before, during, and after construction. Continuously measured water-quality properties include streamflow, specific conductance, water temperature, and turbidity. Discrete sediment samples were collected from June 2009 through September 2012 and analyzed for suspended-sediment concentration (SSC), percentage of sediments less than 63 micrometers (sand-fine break), and loss of material on ignition (analogous to amount of organic matter). Regression models were developed to establish relations between discretely measured SSC samples, and turbidity or streamflow to estimate continuously SSC. Continuous water-quality monitors represented between 96 and 99 percent of the cross-sectional variability for turbidity, and had slopes between 0.91 and 0.98. Because consistent bias was not observed, values from continuous water-quality monitors were considered representative of stream conditions. On average, turbidity-based SSC models explained 96 percent of the variance in SSC. Streamflow-based regressions explained 53 to 60 percent of the variance. Mean squared

  13. Maximum solid concentrations of coal water slurries predicted by neural network models

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Jun; Li, Yanchang; Zhou, Junhu; Liu, Jianzhong; Cen, Kefa


    The nonlinear back-propagation (BP) neural network models were developed to predict the maximum solid concentration of coal water slurry (CWS) which is a substitute for oil fuel, based on physicochemical properties of 37 typical Chinese coals. The Levenberg-Marquardt algorithm was used to train five BP neural network models with different input factors. The data pretreatment method, learning rate and hidden neuron number were optimized by training models. It is found that the Hardgrove grindability index (HGI), moisture and coalification degree of parent coal are 3 indispensable factors for the prediction of CWS maximum solid concentration. Each BP neural network model gives a more accurate prediction result than the traditional polynomial regression equation. The BP neural network model with 3 input factors of HGI, moisture and oxygen/carbon ratio gives the smallest mean absolute error of 0.40%, which is much lower than that of 1.15% given by the traditional polynomial regression equation. (author)

  14. Implications of Industrial Processing Strategy on Cellulosic Ethanol Production at High Solids Concentrations

    DEFF Research Database (Denmark)

    Cannella, David

    The production of cellulosic ethanol is a biochemical process of not edible biomasses which contain the cellulose. The process involves the use of enzymes to hydrolyze the cellulose in fermentable sugars to finally produce ethanol via fermentative microorganisms (i.e. yeasts). These biomasses...... are the leftover of agricultural productions (straws), not edible crops (giant reed) or wood, thus the ethanol so produced is also called second generation (or 2G ethanol), which differs from the first generation produced from starch (sugar beets mostly). In the industrial production of cellulosic ethanol high...... solids strategy resulted critical for its cost effectiveness: high concentration of initial biomass it will lead to high concentration of the final product (ethanol), thus more convenient to isolate. This thesis investigate the implementation of a high solids loading concept into cellulosic ethanol...

  15. Influence of chemical disorder on energy dissipation and defect evolution in concentrated solid solution alloys (United States)

    Zhang, Yanwen; Stocks, G. Malcolm; Jin, Ke; Lu, Chenyang; Bei, Hongbin; Sales, Brian C.; Wang, Lumin; Béland, Laurent K.; Stoller, Roger E.; Samolyuk, German D.; Caro, Magdalena; Caro, Alfredo; Weber, William J.


    A grand challenge in materials research is to understand complex electronic correlation and non-equilibrium atomic interactions, and how such intrinsic properties and dynamic processes affect energy transfer and defect evolution in irradiated materials. Here we report that chemical disorder, with an increasing number of principal elements and/or altered concentrations of specific elements, in single-phase concentrated solid solution alloys can lead to substantial reduction in electron mean free path and orders of magnitude decrease in electrical and thermal conductivity. The subsequently slow energy dissipation affects defect dynamics at the early stages, and consequentially may result in less deleterious defects. Suppressed damage accumulation with increasing chemical disorder from pure nickel to binary and to more complex quaternary solid solutions is observed. Understanding and controlling energy dissipation and defect dynamics by altering alloy complexity may pave the way for new design principles of radiation-tolerant structural alloys for energy applications. PMID:26507943

  16. Pressure-assisted forming of non-concentric tubular cross sections with solid medium

    DEFF Research Database (Denmark)

    Alves, Luis M.; Silva, Carlos M.A.; Nielsen, Chris Valentin


    hydroforming) or elastomers (tube rubber forming) as pressuring medium, the subject matter of this article is centred in the utilization of low melting point, recyclable, metallic alloys as solid pressurizing medium. The aims and scope of the article are centred on the feasibility of forming straight carbon...... plastic deformation and prevent collapse can be successfully and effectively employed to fabricate non-concentric tubular cross sections for prototypes and small batches of lightweight components....

  17. Effect of mass transfer on concentration wave propagation during anaerobic digestion of solid waste. (United States)

    Vavilin, Vasily A; Shchelkanov, Micael Yu; Rytov, Sergey V


    A distributed model of anaerobic digestion of solid waste was developed to study effects of mass transfer on the rate of propagation of initiation methanogenic area. The diffusion and advection of volatile fatty acids (VFA) and methanogenic biomass were taken into account in the model of a one-dimensional (ID) reactor. It was considered that VFA inhibits both polymer hydrolysis and acetoclastic methanogenesis. This approach allows to view the bioreactor as an active medium that provokes concentration waves from some area of methanogenic initiation (local VFA depression) to the total reactor volume. The model shows that mass transfer-based acceleration of methane production in the reactor is possible when the intensity of VFA utilization in the methanogenic area is sufficient for a complete digestion of the incoming VFA. Otherwise, initiation methanogenic area will be suppressed by increasing concentration of VFA. The obtained results emphasize the importance of considering spatial heterogeneity of the reaction for the analysis of solid anaerobic digestion in bioreactors and landfills. The digestion of solid waste can be optimized by setting the low rate of mass transfer (mixing or leachate recirculation) during lag-phase of the reaction with subsequent increase in the mass transfer rate in parallel with the propagation of methanogenic population. In this case, the rate of concentration waves substantially increases.

  18. Evaluation of Laser In Situ Scattering Instrument for Measuring Concentration of Phytoplankton, Purple Sulfur Bacteria, and Suspended Inorganic Sediments in Lakes


    Serra, Teresa; Colomer, Jordi; Cristina, Xavier P.; Vila, Xavier; Arellano, Juan B.; Casamitjana, Xavier


    A laser in situ scattering and transmissometry (Lisst-100) probe has been used for estimating the particle-size distribution of phytopankton, purple photosynthetic sulphur bacteria (Chromatiaceae), and suspended inorganic sediments in different lakes. Results from Lisst-100 have been compared to laboratory measurements, such as those obtained by using a Galai laser size analyzer (GL), an optical microscope (OM), and a flow cytometer (FC). Although all of these instruments were shown to provid...

  19. Fluorescent material concentration dependency: Förster resonance energy transfer in quasi-solid state DSSCs (United States)

    Kim, Dong Woo; Jo, Hyun-Jun; Thogiti, Suresh; Yang, Weon Ki; Cheruku, Rajesh; Kim, Jae Hong


    Förster resonance energy transfer (FRET) is critical for wide spectral absorption, an increased dye loading, and photocurrent generation of dye-sensitized solar cells (DSSCs). This process consists of organic fluorescent materials (as an energy donor), and an organic dye (as an energy acceptor on TiO2 surfaces) with quasi-solid electrolyte. The judicious choice of the energy donor and acceptor facilitates a strong spectral overlap between the emission and absorption regions of the fluorescent materials and dye. This FRET process enhances the light-harvesting characteristics of quasi-solid state DSSCs. In this study, DSSCs containing different concentrations (0, 1, and 1.5 wt%) of a fluorescent material (FM) as the energy donor are investigated using FRET. The power conversion efficiency of DSSCs containing FMs in a quasi-solid electrolyte increased by 33% over a pristine cell. The optimized cell fabricated with the quasi-solid state DSSC containing 1.0 wt% FM shows a maximum efficiency of 3.38%, with a short-circuit current density ( J SC ) of 4.32 mA/cm-2, and an open-circuit voltage ( V OC ) of 0.68 V under illumination of simulated solar light (AM 1.5G, 100 mW/cm-2). [Figure not available: see fulltext.

  20. Evaluation of intake efficiencies and associated sediment-concentration errors in US D-77 bag-type and US D-96-type depth-integrating suspended-sediment samplers (United States)

    Sabol, Thomas A.; Topping, David J.


    Accurate measurements of suspended-sediment concentration require suspended-sediment samplers to operate isokinetically, within an intake-efficiency range of 1.0 ± 0.10, where intake efficiency is defined as the ratio of the velocity of the water through the sampler intake to the local ambient stream velocity. Local ambient stream velocity is defined as the velocity of the water in the river at the location of the nozzle, unaffected by the presence of the sampler. Results from Federal Interagency Sedimentation Project (FISP) laboratory experiments published in the early 1940s show that when the intake efficiency is less than 1.0, suspended-sediment samplers tend to oversample sediment relative to water, leading to potentially large positive biases in suspended-sediment concentration that are positively correlated with grain size. Conversely, these experiments show that, when the intake efficiency is greater than 1.0, suspended‑sediment samplers tend to undersample sediment relative to water, leading to smaller negative biases in suspended-sediment concentration that become slightly more negative as grain size increases. The majority of FISP sampler development and testing since the early 1990s has been conducted under highly uniform flow conditions via flume and slack-water tow tests, with relatively little work conducted under the greater levels of turbulence that exist in actual rivers. Additionally, all of this recent work has been focused on the hydraulic characteristics and intake efficiencies of these samplers, with no field investigations conducted on the accuracy of the suspended-sediment data collected with these samplers. When depth-integrating suspended-sediment samplers are deployed under the more nonuniform and turbulent conditions that exist in rivers, multiple factors may contribute to departures from isokinetic sampling, thus introducing errors into the suspended-sediment data collected by these samplers that may not be predictable on the basis

  1. Use of drinking water treatment solids for arsenate removal from desalination concentrate. (United States)

    Xu, Xuesong; Lin, Lu; Papelis, Charalambos; Myint, Maung; Cath, Tzahi Y; Xu, Pei


    Desalination of impaired water can be hindered by the limited options for concentrate disposal. Selective removal of specific contaminants using inexpensive adsorbents is an attractive option to address the challenges of concentrate management. In this study, two types of ferric-based drinking water treatment solids (DWTS) were examined for arsenate removal from reverse osmosis concentrate during continuous-flow once-through column experiments. Arsenate sorption was investigated under different operating conditions including pH, arsenate concentration, hydraulic retention time, loading rate, temperature, and moisture content of the DWTS. Arsenate removal by the DWTS was affected primarily by surface complexation, electrostatic interactions, and arsenate speciation. Results indicated that arsenate sorption was highly dependent on initial pH and initial arsenate concentration. Acidic conditions enhanced arsenate sorption as a result of weaker electrostatic repulsion between predominantly monovalent H2AsO4(-) and negatively charged particles in the DWTS. High initial arsenate concentration increased the driving force for arsenate sorption to the DWTS surface. Tests revealed that the potential risks associated with the use of DWTS include the leaching of organic contaminants and ammonia, which can be alleviated by using wet DWTS or discarding the initially treated effluent that contains high organic concentration. Copyright © 2015 Elsevier Inc. All rights reserved.

  2. Refractometer assessment of colostral and serum IgG and milk total solids concentrations in dairy cattle (United States)


    Background Estimation of the quantity of colostral IgG or serum IgG absorbed following ingestion of colostrum by calves is essential for monitoring the effectiveness of colostrum feeding practices on dairy farms. Milk total solids concentrations determination is a critical part of quality assessment of nonsaleable whole milk prior to feeding to calves. To date, on-farm methods to assess colostral IgG, serum IgG or milk total solids concentrations have been performed separately with various instruments. The objective of this study was to evaluate the diagnostic performance of a single electronic, hand-held refractometer for assessing colostral and serum IgG concentrations and milk total solids in dairy cattle. Colostral IgG, serum IgG and milk total solids concentrations were determined by the refractometer. Corresponding analysis of colostral and serum IgG concentrations were determined by radial immunodiffusion (RID) while milk total solids were determined by spectrophotometry. Sensitivity and specificity of the refractometer for colostrum and serum samples were calculated as determined by RID. Sensitivity and specificity of the refractometer for milk samples was calculated as determined by spectrophotometry. Results The sensitivity of the refractometer was 1 for colostral IgG, serum IgG and milk total solids determinations. Specificity of the refractometer was 0.66, 0.24 and 0 for colostral IgG, serum IgG and milk total solids determinations, respectively. The refractometer underestimated colostral IgG, serum IgG and milk total solids concentrations compared to the concentrations determined by RID or spectrophotometry. Conclusions The refractometer was an acceptable, rapid, convenient on-farm method for determining colostral IgG and milk total solids. The refractometer was not an acceptable method for determination of serum IgG concentrations as it severely underestimated the serum IgG concentrations. PMID:25125217

  3. Round Robin test for the determination of nitrogen concentration in solid Lithium

    Energy Technology Data Exchange (ETDEWEB)

    Favuzza, P., E-mail: [ENEA Center, Via Madonna del Piano 10, 50019 Sesto Fiorentino (Italy); Antonelli, A. [ENEA Research Center, Brasimone, 40035, Camugnano (Italy); Furukawa, T. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Groeschel, F. [KIT Research Center, Hermann-von-Helmholtz-Platz 1,76344 Eggenstein-Leopoldshafen (Germany); Hedinger, R. [F4E Research Center, Boltzmannstraße 2, 85748 Garching (Germany); Higashi, T. [University of Tokyo (Japan); Hirakawa, Y.; Iijima, M.; Ito, Y.; Kanemura, T. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Knaster, J. [IFMIF-EVEDA Project Team, Rokkasho (Japan); Kondo, H. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Miccichè, G.; Nitti, F.S. [ENEA Research Center, Brasimone, 40035, Camugnano (Italy); Ohira, S. [JAEA Research Center, Tokai-mura, Ibaraki (Japan); Severi, M. [University of Firenze, Via della Lastruccia 3, 50019 Sesto Fiorentino (Italy); Sugimoto, M. [JAEA Research Center, Rokkasho (Japan); Suzuki, A. [University of Tokyo (Japan); Traversi, R. [University of Firenze, Via della Lastruccia 3, 50019 Sesto Fiorentino (Italy); Wakai, E. [JAEA Research Center, Tokai-mura, Ibaraki (Japan)


    Highlights: • Nitrogen contained in solid Lithium is converted into Ammonium ion. • Ammonium ion is suitably quantified by ionic chromatograph or by Ammonia sensor. • Good agreement of the partner’s results has been achieved. • Maximum operative reproducibility and blank subtraction are necessary. - Abstract: Three different partners, ENEA, JAEA ed University of Tokyo, have been involved during 2014–2015 in the Round Robin experimentation for the assessment of the soundness of the analitycal procedure for the determination of the Nitrogen impurities contained inside a solid Lithium sample. Two different kinds of Lithium samples, differing by about an order of magnitude in Nitrogen concentration (∼230 wppm; ∼20–30 wppm), have been selected for this cross analysis. The agreement of the achieved results appears very good for what concerns the most concentrated Lithium and indicates each partner’s procedure is appropriate and intrinsecally able to lead to meaningful values, characterized by a relative uncertainty of just few %. The smaller agreement in the case of the less concentrated Lithium anyway points out that particular attention must be paid to reduce as much as possible any source of external contamination and highlights the importance of the proper blank subtraction.

  4. Evaluating turbidity and suspended-sediment concentration relations from the North Fork Toutle River basin near Mount St. Helens, Washington; annual, seasonal, event, and particle size variations - a preliminary analysis. (United States)

    Uhrich, Mark A.; Spicer, Kurt R.; Mosbrucker, Adam; Christianson, Tami


    Regression of in-stream turbidity with concurrent sample-based suspended-sediment concentration (SSC) has become an accepted method for producing unit-value time series of inferred SSC (Rasmussen et al., 2009). Turbidity-SSC regression models are increasingly used to generate suspended-sediment records for Pacific Northwest rivers (e.g., Curran et al., 2014; Schenk and Bragg, 2014; Uhrich and Bragg, 2003). Recent work developing turbidity-SSC models for the North Fork Toutle River in Southwest Washington (Uhrich et al., 2014), as well as other studies (Landers and Sturm, 2013, Merten et al., 2014), suggests that models derived from annual or greater datasets may not adequately reflect shorter term changes in turbidity-SSC relations, warranting closer inspection of such relations. In-stream turbidity measurements and suspended-sediment samples have been collected from the North Fork Toutle River since 2010. The study site, U.S. Geological Survey (USGS) streamgage 14240525 near Kid Valley, Washington, is 13 river km downstream of the debris avalanche emplaced by the 1980 eruption of Mount St. Helens (Lipman and Mullineaux, 1981), and 2 river km downstream of the large sediment retention structure (SRS) built from 1987–1989 to mitigate the associated sediment hazard. The debris avalanche extends roughly 25 km down valley from the edifice of the volcano and is the primary source of suspended sediment moving past the streamgage (NF Toutle-SRS). Other significant sources are debris flow events and sand deposits upstream of the SRS, which are periodically remobilized and transported downstream. Also, finer material often is derived from the clay-rich original debris avalanche deposit, while coarser material can derive from areas such as fluvially reworked terraces.

  5. Filterability and Sludge Concentration in Membrane Bioreactors


    Lousada-Ferreira, M.


    The Thesis entitled “Filterability and Sludge Concentration in Membrane Bioreactors” aims at explaining the relation between Mixed Liquid Suspended Solids (MLSS) concentration, the amount of solids in the wastewater being treated, also designated as sludge, and filterability, being the ability of the sludge to be filtrated through a membrane, in a wastewater treatment system designated as Membrane Bioreactor (MBR). An MBR is a wastewater treatment system that combines an activated sludge proc...

  6. Influência de diferentes teores de sólidos insolúveis suspensos nas características reológicas de sucos de abacaxi naturais e despectinizados Influence of different contents of insoluble suspended solidS on rheological characteristics of natural and despectinized pineapple juice

    Directory of Open Access Journals (Sweden)

    Alexandre José de Melo Queiroz


    Full Text Available Estudou-se, neste trabalho, a influência dos sólidos insolúveis suspensos nas características reológicas de sucos de abacaxi in natura e sucos tratados com enzima pectinolítica. Cada um dos dois tipos de suco foi estudado através de seis frações, divididas em quatro peneiradas, uma centrifugada e uma integral, representando seis teores de sólidos insolúveis suspensos. Os dados reométricos foram coletados através de um reômetro Haake rotovisco e os dados experimentais ajustados pelo modelo de Mizrahi-Berk. Das seis frações in natura, quatro apresentaram comportamento pseudoplástico, uma caracterizou-se como newtoniana e outra como dilatante enquanto das seis frações tratadas enzimaticamente cinco apresentaram comportamento pseudoplástico e uma caracterizou-se como newtoniana. O teor de sólidos insolúveis suspensos mostrou-se o principal fator responsável pelo comportamento reológico dos sucos de abacaxi naturais e despectinizados.The influence of insoluble suspended solid contents in rheological characteristics of pineapple juice, both natural and treated with pectinolytic enzymes, was studied. Each type of juice was examined by six fractions, divided into four sievings, one centrifuged and the others whole, representing six contents of insoluble suspended solids. The rheometric data were collected by means of Haake rotovisco rheometer and the experimental data were adjusted by the Mizrahi-Berk model. In the natural material four fractions showed pseudoplastic behaviour, one characterized as newtonian and the others as dilatant, whereas in the enzyme treated material, five fractions presented pseudoplastic behaviour and one was characterized as newtonian. The insoluble suspended solid content was found to be the principal factor responsible for this rheological behaviour of natural and despectinized pineapple juices.

  7. Estimating total suspended sediment yield with probability sampling (United States)

    Robert B. Thomas


    The ""Selection At List Time"" (SALT) scheme controls sampling of concentration for estimating total suspended sediment yield. The probability of taking a sample is proportional to its estimated contribution to total suspended sediment discharge. This procedure gives unbiased estimates of total suspended sediment yield and the variance of the...

  8. Dispersive suspended microextraction. (United States)

    Yang, Zhong-Hua; Liu, Yu; Lu, Yue-Le; Wu, Tong; Zhou, Zhi-Qiang; Liu, Dong-Hui


    A novel sample pre-treatment technique termed dispersive suspended microextraction (DSME) coupled with gas chromatography-flame photometric detection (GC-FPD) has been developed for the determination of eight organophosphorus pesticides (ethoprophos, malathion, chlorpyrifos, isocarbophos, methidathion, fenamiphos, profenofos, triazophos) in aqueous samples. In this method, both extraction and two phases' separation process were performed by the assistance of magnetic stirring. After separating the two phases, 1 μL of the suspended phase was injected into GC for further instrument analysis. Varieties of experiment factors which could affect the experiment results were optimized and the following were selected: 12.0 μL p-xylene was selected as extraction solvent, extraction speed was 1200 rpm, extraction time was 30 s, the restoration speed was 800 rpm, the restoration time was 8 min, and no salt was added. Under the optimum conditions, limits of detections (LODs) varied between 0.01 and 0.05 μg L(-1). The relative standard deviation (RSDs, n=6) ranged from 4.6% to 12.1%. The linearity was obtained by five points in the concentration range of 0.1-100.0 μg L(-1). Correlation coefficients (r) varied from 0.9964 to 0.9995. The enrichment factors (EFs) were between 206 and 243. In the final experiment, the developed method has been successfully applied to the determination of organophosphorus pesticides in wine and tap water samples and the obtained recoveries were between 83.8% and 101.3%. Compared with other pre-treatment methods, DSME has its own features and could achieve satisfied results for the analysis of trace components in complicated matrices. Copyright © 2011 Elsevier B.V. All rights reserved.

  9. Critical micelle concentration values for different surfactants measured with solid-phase microextraction fibers. (United States)

    Haftka, Joris J-H; Scherpenisse, Peter; Oetter, Günter; Hodges, Geoff; Eadsforth, Charles V; Kotthoff, Matthias; Hermens, Joop L M


    The amphiphilic nature of surfactants drives the formation of micelles at the critical micelle concentration (CMC). Solid-phase microextraction (SPME) fibers were used in the present study to measure CMC values of 12 nonionic, anionic, cationic, and zwitterionic surfactants. The SPME-derived CMC values were compared to values determined using a traditional surface tension method. At the CMC of a surfactant, a break in the relationship between the concentration in SPME fibers and the concentration in water is observed. The CMC values determined with SPME fibers deviated by less than a factor of 3 from values determined with a surface tension method for 7 out of 12 compounds. In addition, the fiber-water sorption isotherms gave information about the sorption mechanism to polyacrylate-coated SPME fibers. A limitation of the SPME method is that CMCs for very hydrophobic cationic surfactants cannot be determined when the cation exchange capacity of the SPME fibers is lower than the CMC value. The advantage of the SPME method over other methods is that CMC values of individual compounds in a mixture can be determined with this method. However, CMC values may be affected by the presence of compounds with other chain lengths in the mixture because of possible mixed micelle formation. Environ Toxicol Chem 2016;35:2173-2181. © 2016 SETAC. © 2016 SETAC.

  10. Landsat-Based Long-Term Monitoring of Total Suspended Matter Concentration Pattern Change in the Wet Season for Dongting Lake, China

    Directory of Open Access Journals (Sweden)

    Zhubin Zheng


    Full Text Available Assessing the impacts of environmental change and anthropogenic activities on the historical and current total suspended matter (TSM pattern in Dongting Lake, China, is a large challenge. We addressed this challenge by using more than three decades of Landsat data. Based on in situ measurements, we developed an algorithm based on the near-infrared (NIR band to estimate TSM in Dongting Lake. The algorithm was applied to Landsat images to derive TSM distribution maps from 1978 to 2013 in the wet season, revealing significant inter-annual and spatial variability. The relationship of TSM to water level, precipitation, and wind speed was analyzed, and we found that: (1 sand mining areas usually coincide with regions that have high TSM levels in Dongting Lake; (2 water level and seven-day precipitation were both important to TSM variation, but no significant relationship was found between TSM and wind speed or other meteorological data; (3 the increased level of sand mining in response to rapid economic growth has deeply influenced the TSM pattern since 2000 due to the resuspension of sediment; and (4 TSM variation might be associated with policy changes regarding the management of sand mining; it might also be affected by lower water levels caused by the impoundment of the Three Gorges Dam since 2000.

  11. Influence of Temperature, Agitation, Sludge Concentration and Solids Retention Time on Primary Sludge Fermentation

    Directory of Open Access Journals (Sweden)

    J. Sánchez Rubal


    Full Text Available The aim of this research was to determine the influence of temperature, agitation, sludge concentration, and solids retention time (SRT to obtain readily biodegradable organic matter on primary sludge (PS fermentation, which would be used as substrate in a biological nutrient removal (BNR process. Stirring and heating the sludge as well as increasing SRT improved the PS fermentation, producing a large amount of soluble chemical oxygen demand (SCOD. The influence of each operational parameter on PS hydrolysis was observed clearly. A great performance on SCOD production was obtained when the PS was stirred and heated for 3 days. However, PS concentration did not affect the fermentation. Sludge agitation is a simple process with minimal energy consumption. Warming the sludge is very interesting in those plants with anaerobic digestion, where heat energy is obtained from biogas. Therefore, PS fermentation can be improved with a minimum investment and leveraging existing resources in a wastewater treatment plant (WWTP. Fermenter volume can also be reduced if sludge is being heated and stirred during fermentation.

  12. Unique Challenges for Modeling Defect Dynamics in Concentrated Solid-Solution Alloys (United States)

    Zhao, Shijun; Weber, William J.; Zhang, Yanwen


    Recently developed concentrated solid solution alloys (CSAs) are shown to have improved performance under irradiation that depends strongly on the number of alloying elements, alloying species, and their concentrations. In contrast to conventional dilute alloys, CSAs are composed of multiple principal elements situated randomly in a simple crystalline lattice. As a result, the intrinsic disorder has a profound influence on energy dissipation pathways and defect evolution when these CSAs are subjected to energetic particle irradiation. Extraordinary irradiation resistance, including suppression of void formation by two orders of magnitude at an elevated temperature, has been achieved with increasing compositional complexity in CSAs. Unfortunately, the loss of translational invariance associated with the intrinsic chemical disorder poses great challenges to theoretical modeling at the electronic and atomic levels. Based on recent computer simulation results for a set of novel Ni-containing, face-centered cubic CSAs, we review theoretical modeling progress in handling disorder in CSAs and underscore the impact of disorder on defect dynamics. We emphasize in particular the unique challenges associated with the description of defect dynamics in CSAs.


    Directory of Open Access Journals (Sweden)



    Full Text Available Introduction In duration steps of collection, transfer and disposal of solid wastes and also change of solid wastes to compost, produced leachate includes various pollutants such as heavy metals. The amounts of heavy metals don"t easily degrate in environment and would be concentrated in food chain and caused many problems for environment and human. Thus, the goal of present research is to investigation of heavy metals concentration in municipal solid wastes leachate of Isfahan city and reduction method for this case. Methods. leachate from four transfer station and composting plant was sampled ten times and in the first stage, quality of samples was evaluated from pH, COD, total solids (TS, total volatile solids (TYS, total fixed solids (TFS and heavy metals such as Cadmium, Chromium, Zinc, Copper and Nickel viewpoints. Chemical coagulants such as lime, alum and ferric chloride were applied using the Jar test to reduce heavy metals concentration. Results. The results revealed that mean concentration of heavy metals Cd, Cr. Zn Cu and Ni in leachate was equal to 0.63, 1.22, 7.42, 2.15 and 2.22 mg/l respectively and also the results of statistical analysis (ANOVA showed no significant difference between heavy metals concentration in various stations (P > 0.05. The results of Jar test revealed that optimum pH for chemical precipitation, and also optimum concentration of the three coagulants were 2400, 1400 and 1000 mg/l respectively. Discussion. Under this study elements concentration of leachate as compared with effluent standard (Environmental Protection Agency were exceeded the limits. Alum with 75-95 percent removal has the highest effciency as compared to other coagulants, lime with 70-88 percent removal and ferric chloride with 65-85 percent removal are in next order. Erom economical aspect, lime is cost benefit, ferric chloride and alum are in raked next respectively.

  14. Spatial and temporal dynamics of suspended particle characteristics and composition in Navigation Pool 19 of the Upper Mississippi River (United States)

    Milde, Amanda S.


    Suspended particles are an essential component of large rivers influencing channel geomorphology, biogeochemical cycling of nutrients, and food web resources. The Upper Mississippi River (UMR) is a large floodplain river that exhibits pronounced spatiotemporal variation in environmental conditions and biota, providing an ideal environment for investigating dynamics of suspended particles in large river ecosystems. Here we investigated two questions: (1) How do suspended particle characteristics (e.g., size and morphology) vary temporally and spatially? and (2) What environmental variables have the strongest association with particle characteristics? Water sampling was conducted in June, August, and September of 2013 and 2014 in Navigation Pool 19 of the UMR. A FlowCAM particle imaging system was used to enumerate and measure particles 53–300 µm in diameter for size and shape characteristics (e.g., volume, elongation, and symmetry). Suspended particle characteristics varied considerably over space and time and were strongly associated with discharge and concentrations of nitrate + nitrite (NO3-) and soluble reactive phosphorous (SRP). Particle characteristics in backwaters were distinct from those in other habitats for most of the study period, likely due to reduced hydrologic connectivity and higher biotic production in backwaters. During low discharge, phytoplankton and zooplankton made up relatively greater proportions of the observed particles. Concurrently during low discharge, concentrations of chlorophyll, volatile suspended solids, and total phosphorous were higher. Our results suggest that there are complex interactions among space, time, discharge, and other environmental variables (e.g. water nutrients) which drive suspended particle dynamics in large rivers.

  15. Effects of spray-drying and choice of solid carriers on concentrations of Labrasol® and Transcutol® in solid self-microemulsifying drug delivery systems (SMEDDS)

    National Research Council Canada - National Science Library

    Li, Liang; Yi, Tao; Lam, Christopher Wai-Kei


    ...® are used widely as surfactant and solubilizer in the formulation of solid SMEDDS. We investigated the effects of spray-drying and the use of different solid carriers on concentrations of Labrasol® and Transcutol...

  16. New spray congealing atomizer for the microencapsulation of highly concentrated solid and liquid substances. (United States)

    Albertini, Beatrice; Passerini, Nadia; Pattarino, Franco; Rodriguez, Lorenzo


    A new pneumatic atomizer for spray congealing, called wide pneumatic nozzle (WPN), was developed. To evaluate its performance, microparticles containing highly concentrated either solid drug (Propafenone hydrochloride, PRF) or liquid nutraceutical (Vitamin E, VE) have been prepared and characterized. The results showed that the spray congealing nozzle enabled the production of spherical and not aggregated microparticles with high yields (95% w/w) and relatively narrow size distributions; moreover, increasing the viscosity of the suspension from 50 to 500 mPa s, the particle size increased. The loading of the drug was high for microspheres (50% for PRF and 30% for VE) and the encapsulation efficiency was good for all formulations. The drug release was easily modified according to the nature of the used excipients, as both lipophilic (carnauba wax, cetearyl and stearyl alcohols) and hydrophilic (PEG 4000) carriers were employed. Moreover the results evidenced that it was possible to encapsulate actives (VE) that are in a liquid form and to enhance their availability. In conclusion the developed spray congealing nozzle was able to nebulize very viscous systems that are usually not processed by conventional apparatus and to produce microspheres with high and uniform drug content.

  17. Development of a sensitive solid-phase radioimmunoassay for melanin-concentrating hormone

    Energy Technology Data Exchange (ETDEWEB)

    Eberle, A.N.; Baumann, J.B.; Girard, J. (Univ. Children' s Hospital, Basel (Switzerland)); Baker, B.I.; Kishida, M. (Univ. of Bath (England))


    A two-step solid-phase radioimmunoassay for melanin-concentrating hormone (MCH) was developed for direct determination of the hormone in plasma samples. To this end, synthetic MCH was coupled to bovine thyreoglobulin and the complex was injected into rabbits. Specific antisera of high titer were obtained which did not crossreact with other hormones. The IgGs were chemically linked to immunobeads, an acrylamide/acrylic acid polymer matrix. In the first step, plasma MCH was immunoextracted by incubation of diluted plasma samples with anti-MCH immunobeads. In the second step, the washed polymer was incubated with radioiodinated MCH tracer for titration of non-occupied sites. This procedure made it possible to determine as little as 4 pg MCH per ml of plasma. Application of the radioimmunoassay to plasma levels of black or white background-adapted trout showed a marked difference in circulating MCH: while trout on a black background contained a mean value of 29 {plus minus} 5.6 pg/ml, animals on a white background had 106 {plus minus} 19 pg/ml.

  18. Sorption behavior of selenium on humic acid under increasing selenium concentration or increasing solid/liquid ratio

    Energy Technology Data Exchange (ETDEWEB)

    Kamei-Ishikawa, Nao [Office of Biospheric Assessment for Waste Disposal, National Institute of Radiological Sciences, Anagawa 4-9-1, Inage, Chiba 263-8555 (Japan)], E-mail:; Nakamaru, Yasuo [Department of Bioproduction, Tokyo University of Agriculture, Yasaka 196, Abashiri, Hokkaido 099-2493 (Japan)], E-mail:; Tagami, Keiko [Office of Biospheric Assessment for Waste Disposal, National Institute of Radiological Sciences, Anagawa 4-9-1, Inage, Chiba 263-8555 (Japan)], E-mail:; Uchida, Shigeo [Office of Biospheric Assessment for Waste Disposal, National Institute of Radiological Sciences, Anagawa 4-9-1, Inage, Chiba 263-8555 (Japan)], E-mail:


    The sorption of selenium (Se) on humic acid (HA) was investigated in order to better understand the fate of stable and radioactive Se in soils and sediments. An ultrafiltration technique was used to determine size distributions of HA-sorbed-Se when increasing Se concentration and solid/liquid ratio. The results showed that the Se sorption onto HA followed the Freundlich isotherm. No solid/liquid ratio-dependence was observed especially when <3 kDa molecular size fraction was used from solid/liquid separation. The Freundlich isotherm parameters K{sub F} and n obtained using the <3 kDa molecular size fraction for solid/liquid separation were 3.7 x 10{sup 2} and 0.82, respectively. In addition, since dissolved HA increased with decreased ionic strength in the HA suspension, ionic strength could promote aggregation of HA. The conformational change of HA could affect the sorption behavior of Se on HA.

  19. Estuarine Suspended Sediment Dynamics: Observations Derived from over a Decade of Satellite Data

    Directory of Open Access Journals (Sweden)

    Anthony Reisinger


    Full Text Available Suspended sediment dynamics of Corpus Christi Bay, Texas, USA, a shallow-water wind-driven estuary, were investigated by combining field and satellite measurements of total suspended solids (TSS. An algorithm was developed to transform 500-m Moderate Resolution Imaging Spectroradiometer (MODIS Aqua satellite reflectance data into estimated TSS values. The algorithm was developed using a reflectance ratio regression of MODIS Band 1 (red and Band 3 (green with TSS measurements (n = 54 collected by the Texas Commission on Environmental Quality for Corpus Christi Bay and other Texas estuaries. The algorithm was validated by independently collected TSS measurements during the period of 2011–2014 with an uncertainty estimate of 13%. The algorithm was applied to the period of 2002–2014 to create a synoptic time series of TSS for Corpus Christi Bay. Potential drivers of long-term variability in suspended sediment were investigated. Median and IQR composites of suspended sediments were generated for seasonal wind regimes. From this analysis it was determined that long-term, spatial patterns of suspended sediment in the estuary are related to wind-wave resuspension during the predominant northerly and prevalent southeasterly seasonal wind regimes. The impact of dredging is also apparent in long-term patterns of Corpus Christi Bay as concentrations of suspended sediments over dredge spoil disposal sites are higher and more variable than surrounding areas, which is most likely due to their less consolidated sediments and shallower depths requiring less wave energy for sediment resuspension. This study highlights the advantage of how long-synoptic time series of TSS can be used to elucidate the major drivers of suspended sediments in estuaries.

  20. Analyzing freely dissolved concentrations of cationic surfactant utilizing ion-exchange capability of polyacrylate coated solid-phase microextraction fibers

    NARCIS (Netherlands)

    Chen, Y.|info:eu-repo/dai/nl/322994179; Droge, S.T.J.|info:eu-repo/dai/nl/304834017; Hermens, J.L.M.|info:eu-repo/dai/nl/069681384


    A 7-μm polyacrylate (PA) coated fiber was successfully employed to determine freely dissolved concentrations of cationic surfactants by solid-phase microextraction (SPME) and utilizing the capability of the PA-coating to sorb organic cations via ion-exchange at carboxylic groups. Measured

  1. Representation of solid and nutrient concentrations in irrigation water from tailwater recovery systems by surface water grab samples (United States)

    Tailwater recovery (TWR) systems are being implemented on agricultural landscapes to create an additional source of irrigation water. Existing studies have sampled TWR systems using grab samples; however, the applicability of solids and nutrient concentrations in these samples to water being irrigat...

  2. Regionally tuned algorithm to study the seasonal variation of suspended sediment concentration using IRS-P4 Ocean Colour Monitor data

    Directory of Open Access Journals (Sweden)

    Kumar Avinash


    The tuned regional algorithm was used to estimate SSC in 2004, 2005 and 2007 which shows the concentration varied from 1.13 to 28.1 mg/l in 2004, 1.84 to 23.12 mg/l in 2005 and 2 to 27.85 mg/l in 2007. Graphical and statistical methods using analysis of variance (ANOVA have shown significant seasonal variability and inter-station spatial variability in SSC. Peak concentrations were recorded in the post-monsoon followed by the pre-monsoon period. The wind, wave and current pattern associated with southwest monsoon possibly controls the seasonal distribution, while nearshore turbulence and littoral transport influence the spatial distribution. This paper clearly demonstrated the potential application of regionally tuned algorithm for SSC mapping to study the spatial and seasonal pattern in shallow water off southern Karnataka.

  3. Low concentration DNA extraction and recovery using a silica solid phase.

    Directory of Open Access Journals (Sweden)

    Constantinos Katevatis

    Full Text Available DNA extraction from clinical samples is commonly achieved with a silica solid phase extraction column in the presence of a chaotrope. Versions of these protocols have been adapted for point of care (POC diagnostic devices in miniaturized platforms, but commercial kits require a high amount of input DNA. Thus, when the input clinical sample contains less than 1 μg of total DNA, the target-specific DNA recovery from most of these protocols is low without supplementing the sample with exogenous carrier DNA. In fact, many clinical samples used in the development of POC diagnostics often exhibit target DNA concentrations as low as 3 ng/mL. With the broader goal of improving the yield and efficiency of nucleic acid-based POC devices for dilute samples, we investigated both DNA adsorption and recovery from silica particles by using 1 pg- 1 μg of DNA with a set of adsorption and elution buffers ranging in pH and chaotropic presence. In terms of adsorption, we found that low pH and the presence of chaotropic guanidinium thiocyanate (GuSCN enhanced DNA-silica adsorption. When eluting with a standard low-salt, high-pH buffer, > 70% of DNA was unrecoverable, except when DNA was initially adsorbed with 5 M GuSCN at pH 5.2. Unrecovered DNA was either not initially adsorbed or irreversibly bound on the silica surface. Recovery was improved when eluting with 95°C formamide and 1 M NaOH, which suggested that DNA-silica-chaotrope interactions are dominated by hydrophobic interactions and hydrogen bonding. While heated formamide and NaOH are non-ideal elution buffers for practical POC devices, the salient results are important for engineering a set of optimized reagents that could maximize nucleic acid recovery from a microfluidic DNA-silica-chaotrope system.

  4. Suspended silt concentrations in the lower Olifants River (Mpumalanga and the impact of silt releases from the Phalaborwa Barrage on water quality and fish survival

    Directory of Open Access Journals (Sweden)

    Y. Buermann


    Full Text Available Silt loads in the Olifants and Sabie river systems inside the Kruger National Park, were monitored by collecting water samples every consecutive week for a period of 20 months. The variation in silt concentration, changes in selected physico-chemical water quality variables and fish mortalities during flushing (i.e. release of silt, by sluicing of the Phalaborwa Barrage, were also monitored. The Olifants River inside the Kruger National Park carried high silt loads in summer; in the dry season the suspensoid load was greatly reduced. A similar pattern was observed in the Sabie River, but the silt loads were generally lower. It was apparent that silt loads released from the Phalaborwa Barrage led to large variations in the natural silt loads of the Olifants River. These increased amounts of silt (25 000 mg/1 to >70 000 mg/1 caused drastic reductions in the dissolved oxygen concentration of the water, ranging from >6 mg/1 to 0 mg/1. Depending on the severity and duration of the flushing, fish succumb to such silt loads. These findings, as well as published information, indicate that the management strategy of flushing to improve storage capacity is ecological unacceptable. It is therefore suggested that the use of the Phalaborwa Barrage as a future reservoir should be critically re-evaluated.

  5. On the origin and variability of suspended particulate matter (PM1, PM2.5 and PM10) concentrations in Cyprus. (United States)

    Pikridas, Michael; Vrekoussis, Mihalis; Mihalopoulos, Nikolaos; Kizas, Christos; Savvides, Chrysanthos; Sciare, Jean


    The Eastern Mediterranean (EM) lies at the crossroad of three different continents (Europe, Asia, and Africa). EM is a densely populated region including several cities with 3M inhabitants or more (e.g. Athens, Istanbul, Izmir, and Cairo). It has been identified as the most polluted area in Europe with respect to particulate matter (PM) mainly due to the combination of high photochemical activity, which causes pollutants to oxidize and partitioning in the particle phase, with the elevated pollutants emissions from neighboring regions. In addition, the proximity to Africa and the Middle East allows frequent transport of dust particles. At the center of the Eastern Mediterranean lies the island of Cyprus, which has received very little attention regarding its PM levels despite being the location in Europe most frequently impacted by air masses from the Middle East. Herewith, we present a historical PM archive that spans 2 decades. It involves ongoing monitoring on a daily basis of particulate matter with diameters smaller than 10 μm (PM10), 2.5 μm (PM2.5), and 1 μm (PM1) conducted in at least one, of the 12 currently existing air quality stations in Cyprus since 1997, 2005, and 2009, respectively. The most extended PM datasets correspond a) to the Agia Marina Xyliatou (AMX) monitoring station established at a remote area at the foothills of mount Troodos and b) that of the inland capital, Nicosia. Based on this long-term dataset, the diurnal, temporal and annual variability is assessed. Prior to 2010, PM10 concentration at all sites remained relatively constant, but at different levels, violating the annual EU legislated PM10 limit of 40 μg m-3. Since 2010, coarse mode levels have decreased at all sites. The reported decrease was equal to 30% at AMX. As a result, since 2010 the observed levels comply with the EU legislation threshold. Satellite observations of Aerosol Optical Thickness (AOT) Moderate Resolution Imaging Spectroradiometer (MODIS) onboard NASA

  6. Formation of concentrated solid clusters in a liquid-solid mixture by ultrasonic wave. Experimental considerations; Choonpa ni yoru suichu ryushi no cluster keisei. Jikkenteki kosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Imai, T. [Akita University, Akita (Japan). Mining College; Asakura, K.; Kaneko, T.; Nakajima, I. [Hokkaido University, Sapporo (Japan). Faculty of Engineering


    It is a well-known fact that a little fine dust in a glass tube containing a vibrating column of air disposes itself in recurring patterns. These stripped dust patterns are called as `Kundt`s Dust Figures` in honor of his discovery. The purpose of the present study is to apply the Kundt`s method to solid-liquid mixtures for making concentrated solid clusters in a tube. Ultrasonic wave was used as a source of vibration. Two types of polystyrene particles and fine titanium oxide particles (powder) were used for the experiments. As the results of the experiments, the neutrally buoyant polystyrene particles formed regular stripes of concentrated clusters in salt water. With increasing the particle concentration, the stripes of the clusters disappeared and a massive cluster was gradually formed at the upper part of the tube. The particles slightly heavier than liquid also made a massive cluster in the middle of the tube. The fine titanium oxide particles did not show clear cluster patterns, however, after draining the mixture, the particles remaining on the inside wall of the tube indicated the formation of weak stripes. 12 refs., 22 figs.

  7. Acoustic backscatter by suspended cohesive sediments: Field observations, Seine Estuary, France (United States)

    Sahin, Cihan; Verney, Romaric; Sheremet, Alexandru; Voulgaris, George


    Observations of suspended sediment size and concentration, flow and acoustic backscatter intensity collected on the Seine Estuary (France) are used to study the acoustic response in cohesive-sediment dominated environments. Estimates of suspended sediment concentration based on optical backscatter sensors and water samples are used to calibrate the acoustic backscatter intensity. The vertical structure of suspended sediment concentration is then estimated from acoustic backscatter information. To our knowledge, this is the first field application of the recently proposed model of acoustic scattering by flocculating suspensions based on the variation of particle density (floc-scattering model). The estimates of sediment concentration reproduce well the observations under different tidal (neap/spring) conditions, confirming the applicability of the new model in the field when detailed particle size measurements are available. When particle size measurements are not available, using estimated floc sizes based on the turbulence intensities may provide reasonable SSC profiles. During spring tide events (associated with strong currents, small flocs and large concentrations), the performances of the new floc-scattering model and the previous models given for solid particle-scattering are comparable. The floc-scattering model increases the quality of the SSC estimates especially during low-energy conditions characterized with larger flocs.

  8. Effect of water hardness and dissolved-solid concentration on hatching success and egg size in bighead carp (United States)

    Chapman, Duane C.; Deters, Joseph E.


    Bighead carp Hypophthalmichthys nobilis is an Asian species that has been introduced to the United States and is regarded as a highly undesirable invader. Soft water has been said to cause the bursting of Asian carp eggs and thus has been suggested as a factor that would limit the spread of this species. To evaluate this, we subjected fertilized eggs of bighead carp to waters with a wide range of hardness and dissolved-solid concentrations. Hatching rate and egg size were not significantly affected by the different water qualities. These results, combined with the low hardness (28–84 mg/L) of the Yangtze River (the primary natal habitat of Hypophthalmichthys spp.), suggest that managers and those performing risk assessments for the establishment of Hypophthalmichthys spp. should be cautious about treating low hardness and dissolved-solid concentrations as limiting factors.

  9. Development of a depth-integrated sample arm (DISA) to reduce solids stratification bias in stormwater sampling (United States)

    Selbig, William R.; ,; Roger T. Bannerman,


    A new depth-integrated sample arm (DISA) was developed to improve the representation of solids in stormwater, both organic and inorganic, by collecting a water quality sample from multiple points in the water column. Data from this study demonstrate the idea of vertical stratification of solids in storm sewer runoff. Concentrations of suspended sediment in runoff were statistically greater using a fixed rather than multipoint collection system. Median suspended sediment concentrations measured at the fixed location (near the pipe invert) were approximately double those collected using the DISA. In general, concentrations and size distributions of suspended sediment decreased with increasing vertical distance from the storm sewer invert. Coarser particles tended to dominate the distribution of solids near the storm sewer invert as discharge increased. In contrast to concentration and particle size, organic material, to some extent, was distributed homogenously throughout the water column, likely the result of its low specific density, which allows for thorough mixing in less turbulent water.

  10. Decadal-scale changes in dissolved-solids concentrations in groundwater used for public supply, Salt Lake Valley, Utah (United States)

    Thiros, Susan A.; Spangler, Larry


    Basin-fill aquifers are a major source of good-quality water for public supply in many areas of the southwestern United States and have undergone increasing development as populations have grown over time. During 2005, the basin-fill aquifer in Salt Lake Valley, Utah, provided approximately 75,000 acre-feet, or about 29 percent of the total amount of water used by a population of 967,000. Groundwater in the unconsolidated basin-fill deposits that make up the aquifer occurs under unconfined and confined conditions. Water in the shallow unconfined part of the groundwater system is susceptible to near-surface contamination and generally is not used as a source of drinking water. Groundwater for public supply is withdrawn from the deeper unconfined and confined parts of the system, termed the principal aquifer, because yields generally are greater and water quality is better (including lower dissolved-solids concentrations) than in the shallower parts of the system. Much of the water in the principal aquifer is derived from recharge in the adjacent Wasatch Range (mountain-block recharge). In many areas, the principal aquifer is separated from the overlying shallow aquifer by confining layers of less permeable, fine-grained sediment that inhibit the downward movement of water and any potential contaminants from the surface. Nonetheless, under certain hydrologic conditions, human-related activities can increase dissolved-solids concentrations in the principal aquifer and result in groundwater becoming unsuitable for consumption without treatment or mixing with water having lower dissolved-solids concentrations. Dissolved-solids concentrations in areas of the principal aquifer used for public supply typically are less than 500 milligrams per liter (mg/L), the U.S. Environmental Protection Agency (EPA) secondary (nonenforceable) drinking-water standard. However, substantial increases in dissolved-solids concentrations in the principal aquifer have been documented in some

  11. Effect of mixture ratio, solids concentration and hydraulic retention time on the anaerobic digestion of the organic fraction of municipal solid waste. (United States)

    Fongsatitkul, Prayoon; Elefsiniotis, Panagiotis; Wareham, David G


    This paper describes how the degradation of the organic fraction of municipal solid waste (OFMSW) is affected through codigestion with varying amounts of return activated sludge (RAS). Solid waste that had its inorganic fraction selectively removed was mixed with RAS in ratios of 100% OFMSW, 50% OFMSW/50% RAS, and 25% OFMSW/75% RAS. The total solids (TS) concentration was held at 8% and three anaerobic digester systems treating the mixtures were held (for the first run) at a total hydraulic retention time (HRT) of 28 days. Increasing amounts of RAS did not however improve the mixture's digestability, as indicated by little change and/or a drop in the main performance indices [including percentage volatile solids (VS) removal and specific gas production]. The optimum ratio in this research therefore appeared to be 100% OFMSW with an associated 85.1 ± 0.6% VS removal and 0.72 ± 0.01 L total gas g(- 1) VS. In the second run, the effect of increasing percentage of TS (8, 12% and 15%) at a system HRT of 28 days was observed to yield no improvement in the main performance indices (i.e. percentage VS removal and specific gas production). Finally, during the third run, variations in the total system HRT were investigated at an 8% TS, again using 100% OFMSW. Of the HRTs explored (23, 28 and 33 days), the longest HRT yielded the best performance overall, particularly in terms of specific gas production (0.77 ± 0.01 L total gas g(-1) VS).

  12. Comparison between in vitro properties of washed platelet concentrates suspended in M-sol and those in BRS-A, both of which were prepared with an automated cell processor. (United States)

    Iwama, Akira; Hirayama, Junichi; Nogawa, Masayuki; Shiba, Masayuki; Satake, Masahiro; Takamoto, Shigeru; Tadokoro, Kenji


    Washed platelet concentrate (WPC) is prepared manually in general, but automated preparation is desirable to minimize variation in the WPC quality and enhance WPC production. Recently, the software was improved for an automated cell processor (ACP) to control all processes of WPC preparation. M-sol and BRS-A, which are mixtures of medical solutions, are widely used for WPC preparation with a manual method in Japan. In this study, we prepared WPC suspended in M-sol (WPC-M) or BRS-A (WPC-B) with the ACP, and compared their in vitro properties during 7-day storage. PC was divided into two equal aliquots for WPC-M and WPC-B. A divided PC, medical solutions and disposable materials were set in the ACP, and it was started to prepare WPC-M or WPC-B on Day 0. Prepared WPC was stored on a flatbed shaker until Day 7. The pH of WPC-M and WPC-B was maintained above 6.8 during the 7-day storage. The differences in aggregation (%), HSR (%), P-selectin expression, GPIbα expression, and phosphatidylserine expression between WPC-M and WPC-B were minimal until Day 3. The in vitro properties of WPC-B are not markedly different from those of WPC-M until Day 3. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Impact of sound attenuation by suspended sediment on ADCP backscatter calibrations

    NARCIS (Netherlands)

    Sassi, M.G.; Hoitink, A.J.F.; Vermeulen, B.


    Although designed for velocity measurements, acoustic Doppler current profilers (ADCPs) are widely being used to monitor suspended particulate matter in rivers and in marine environments. To quantify mass concentrations of suspended matter, ADCP backscatter is generally calibrated with in situ

  14. A depth integrated model for suspended transport

    NARCIS (Netherlands)

    Galappatti, R.


    A new depth averaged model for suspended sediment transport in open channels has been developed based on an asymptotic solution to the two dimensional convection-diffusion equation in the vertical plane. The solution for the depth averaged concentration is derived from the bed boundary condition and

  15. Atmospheric trace metal concentrations in Suspended Particulate ...

    African Journals Online (AJOL)

    The particulate samples from where the metals were characterized and quantified, were collected between December 2007 and March 2008, using a Gravimetric technique a portable SKC 506673 High volume Gravimetric sampler. The air particulate samples were collected from the kitchens, living rooms and outdoor ...

  16. Suspended sediment concentration and particle size distribution ...

    Indian Academy of Sciences (India)

    ... particle size distribution (PSD) were correlated with HMC by using bivariate and multivariate regression models. Proposed models were then selected based on statistical criteria. The results showed high correlation between dissolved and particulate chromium content with efficiency coefficients beyond 77% ( > 0.001).

  17. Simulation of suspended sediment transport initialized with satellite ...

    Indian Academy of Sciences (India)

    Suspended sediment transport in the Gulf of Kachchh is simulated utilizing the suspended sediment concentration (SSC) derived from Oceansat OCM imagery, as the initial condition in MIKE-21 Mud. Transport model. Optimization of the model mud parameters, like settling velocity and critical shear stress for erosion are ...

  18. Simulation of suspended sediment transport initialized with satellite ...

    Indian Academy of Sciences (India)

    Suspended sediment transport in the Gulf of Kachchh is simulated utilizing the suspended sediment concentration (SSC) derived from Oceansat OCM imagery, as the initial condition in MIKE-21 Mud Transport model. Optimization of the model mud parameters, like settling velocity and critical shear stress for erosion are ...

  19. Successive membrane separation processes simplify concentration of lipases produced by Aspergillus niger by solid-state fermentation. (United States)

    Reinehr, Christian Oliveira; Treichel, Helen; Tres, Marcus Vinicius; Steffens, Juliana; Brião, Vandré Barbosa; Colla, Luciane Maria


    In this study, we developed a simplified method for producing, separating, and concentrating lipases derived from solid-state fermentation of agro-industrial residues by filamentous fungi. First, we used Aspergillus niger to produce lipases with hydrolytic activity. We analyzed the separation and concentration of enzymes using membrane separation processes. The sequential use of microfiltration and ultrafiltration processes made it possible to obtain concentrates with enzymatic activities much higher than those in the initial extract. The permeate flux was higher than 60 L/m2 h during microfiltration using 20- and 0.45-µm membranes and during ultrafiltration using 100- and 50-kDa membranes, where fouling was reversible during the filtration steps, thereby indicating that the fouling may be removed by cleaning processes. These results demonstrate the feasibility of lipase production using A. niger by solid-state fermentation of agro-industrial residues, followed by successive tangential filtration with membranes, which simplify the separation and concentration steps that are typically required in downstream processes.

  20. Effect of substrate concentration on dry mesophilic anaerobic digestion of organic fraction of municipal solid waste (OFMSW). (United States)

    Fernández, J; Pérez, M; Romero, L I


    The influence of total solid contents during anaerobic mesophilic treatment of the organic fraction of municipal solid waste (MSW) has been studied in this work. The work was performed in batch reactors of 1.7L capacity, during a period of 85-95 days. Two different organic substrate concentrations were studied: 931.1 mgDOC/L (20% TS) and 1423.4 mgDOC/L (30% TS). Experimental results showed that the reactor with 20% total solids content had significantly higher performance. Thus, the startup phase ended at 14 days and the total DOC removal was 67.53%. The startup in reactor R30 ended at 28 days obtaining 49.18% DOC removal. Also, the initial substrate concentration contributed substantially to the amount of methane in the biogas. Hence, the total methane production in the methanogenic phase was 7.01 L and 5.53 L at the end of the experiments for R20 and R30, respectively.

  1. Enzymatic hydrolysis and succinic acid fermentation from steam-exploded corn stalk at high solid concentration by recombinant Escherichia coli. (United States)

    Wu, Dexi; Li, Qiang; Wang, Dan; Dong, Yugang


    Steam-exploded corn stalk biomass was used as the substrate for succinic acid production via lignocellulose enzymatic hydrolysis and fermentation. Succinic acid fermentation was investigated in Escherichia coli strains overexpressing cyanobacterium Anabaena sp. 7120 ecaA gene encoding carbonic anhydrase (CA). For the washed steam-exploded corn stalk at 30 % substrate concentration, i.e., 30 % water-insoluble solids (WIS), enzymatic hydrolysis yielded 97.5 g/l glucose solution and a cellulose conversion of 73.6 %, thus a high succinic acid level up to 38.6 g/l. With the unwashed steam-exploded corn stalk, though a cellulose conversion of 71.2 % was obtained in hydrolysis at 30 % solid concentration (27.9 % WIS), its hydrolysate did not ferment at all, and the hydrolysate of 25 % solid loading containing 3.8 g/l acetic acid and 168.2 mg/l furfural exerted a strong inhibition on succinic acid production.

  2. Cable suspended windmill (United States)

    Farmer, Moses G. (Inventor)


    A windmill is disclosed which includes an airframe having an upwind end and a downwind end. The first rotor is rotatably connected to the airframe, and a generator is supported by the airframe and driven by the rotor. The airframe is supported vertically in an elevated disposition by poles which extend vertically upwardly from the ground and support cables which extend between the vertical poles. Suspension cables suspend the airframe from the support cable.

  3. Controlling thermal properties of dense gas fluidized beds for concentrated solar power by internal and external solids circulation (United States)

    Ammendola, Paola; Bareschino, Piero; Chirone, Riccardo; Salatino, Piero; Solimene, Roberto


    Fluidization technology displays a long record of success stories, mostly related to applications to thermal and thermochemical processes, which are fostering extension to novel and relatively unexplored fields. Application of fluidized beds to collection and thermal storage of solar radiation in Concentrated Solar Power (CSP) is one of the most promising, a field which poses challenging issues and great opportunities to fluidization scientists and technologists. The potential of this growing field calls for reconsideration of some of the typical design and operation guidelines and criteria, with the goal of exploiting the inherently good thermal performances of gas-fluidized beds at their best. "Creative" and non-conventional design and operation of fluidized beds, like those based on internal and external solids circulation, may be beneficial to the enhancement of thermal diffusivity and surface-to-bed heat transfer, improving the potential for application in the very demanding context of CSP with thermal energy storage. This paper investigated: i) a fluidized bed configuration with an uneven distribution of the fluidizing gas to promote vortices in the scale of bed height (internal solids circulation); ii) a dual fluidized bed configuration characterized by an external solids circulation achieved by the operation of a riser and a bubbling fluidized bed. CFD simulations showed the hydrodynamics conditions under which the internal solids circulation was established. The hydrodynamic characterization of the external solids circulation was achieved by an experimental study carried out with different cold models. The dual fluidized bed system was optimized in terms of operating conditions and geometrical features of the connections between two fluidized beds.

  4. Indoor concentrations of nitrogen dioxide and sulfur dioxide from burning solid fuels for cooking and heating in Yunnan Province, China. (United States)

    Seow, W J; Downward, G S; Wei, H; Rothman, N; Reiss, B; Xu, J; Bassig, B A; Li, J; He, J; Hosgood, H D; Wu, G; Chapman, R S; Tian, L; Wei, F; Caporaso, N E; Vermeulen, R; Lan, Q


    The Chinese national pollution census has indicated that the domestic burning of solid fuels is an important contributor to nitrogen dioxide (NO2 ) and sulfur dioxide (SO2 ) emissions in China. To characterize indoor NO2 and SO2 air concentrations in relation to solid fuel use and stove ventilation in the rural counties of Xuanwei and Fuyuan, in Yunnan Province, China, which have among the highest lung cancer rates in the nation, a total of 163 participants in 30 selected villages were enrolled. Indoor 24-h NO2 and SO2 samples were collected in each household over two consecutive days. Compared to smoky coal, smokeless coal use was associated with higher NO2 concentrations [geometric mean (GM) = 132 μg/m(3) for smokeless coal and 111 μg/m(3) for smoky coal, P = 0.065] and SO2 [limit of detection = 24 μg/m(3) ; percentage detected (%Detect) = 86% for smokeless coal and 40% for smoky coal, P < 0.001]. Among smoky coal users, significant variation of NO2 and SO2 air concentrations was observed across different stove designs and smoky coal sources in both counties. Model construction indicated that the measurements of both pollutants were influenced by stove design. This exposure assessment study has identified high levels of NO2 and SO2 as a result of burning solid fuels for cooking and heating. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  5. Effects of change in concentration of lead on the properties of Bi-2223 superconductor prepared through solid state reaction.

    Directory of Open Access Journals (Sweden)

    Moeen Piracha


    Full Text Available In this work, superconducting pellets without lead (Pb as well as with different concentrations of lead are prepared by solid state reaction. The prepared samples are then characterized using X-ray powder diffraction (XRD, scanning electron microscope (SEM, and energy-dispersive X-ray spectroscopy (EDX. The superconducting properties are examined using electrical resistivity and transport critical current density Jc. Our results show that the sample prepared with calcination of 48 hours with intermediate grinding has the ideal value of the superconducting transition temperature Tc and transport critical current density Jc.

  6. Depth-integrated suspended sediment and geochemical fluxes in large rivers: the Amazon River system (United States)

    Bouchez, J.; Lupker, M.; Gaillardet, J.; Metivier, F.; France-Lanord, C.; Maurice, L.


    Erosion and weathering produce a wide range of residual solid products, in terms of size, density, mineralogy and chemical composition. These solid products are then transported by rivers from the continents to the oceans as suspended particulate matter (SPM) and bedload. Large rivers account for an important part of this transfer of sediments at the global scale. In those rivers, deep channels allow for vertical differentiation, or sorting, of suspended sediment, following their size and density. This hydrodynamic sorting results in vertically heterogeneous depth-profiles in terms of SPM concentration and size distribution (e.g. Garcia, 2008), which in turn likely result in an heterogeneous chemical composition of SPM throughout channel depth (e.g. Galy, 2007), which has to be evaluated. We sampled river water of the main tributaries of the Amazon River system (in the lowland basin), at two distinct water-stages, at various depths following depth-profiles, using a point depth-sampler. After filtration, and SPM recovery, SPM concentration, grain size distribution and chemical composition were determined. River discharge and water velocity throughout the sampled cross-sections were recorded using Acoustic Doppler Current Profiler (ADCP). The large increase in SPM concentration with depth observed at most of the sampled depth-profiles is well accounted for by the Rouse model (e.g. Rouse, 1950). This analysis allows us to reliably infer the SPM concentration and grain size distribution throughout the sampled river cross-section, and thus to estimate the spatially-integrated instantaneous SPM flux using ADCP data (Bouchez et al., 2010). The study also emphasizes the potential role of particle aggregation, within the river system, as a complicating factor regarding the prediction of these depth-integrated SPM fluxes from easily measurable hydrodynamic parameters (surface SPM concentration and grain size, and water velocity). Then, using the previous analysis, combined

  7. An analytical protocol for the determination of total mercury concentrations in solid peat samples

    DEFF Research Database (Denmark)

    Roos-Barraclough, F; Givelet, N; Martinez-Cortizas, A


    Traditional peat sample preparation methods such as drying at high temperatures and milling may be unsuitable for Hg concentration determination in peats due to the possible presence of volatile Hg species, which could be lost during drying. Here, the effects of sample preparation and natural....... A comparison of two Hg profiles from an Arctic peat core, measured in frozen samples and in air-dried samples, revealed that no Hg losses occurred upon air-drying. A comparison of Hg concentrations in several plant species that make up peat, showed that some species (Pinus mugo, Sphagnum recurvum...... concentration in individual peat slices. Several subsamples from each peat slice are air dried, combined and measured for Hg using the AMA254, using a program of 30 s (drying), 125 s (decomposition) and 45 s (waiting). Bulk density and water content measurements are performed on every slice using separate...

  8. Anaerobic digestion of ultrasonicated sludge at different solids concentrations - Computation of mass-energy balance and greenhouse gas emissions. (United States)

    Pilli, Sridhar; Yan, S; Tyagi, R D; Surampalli, R Y


    Two cases of anaerobic digestion (AD) of sludge, namely (i) with pre-treatment and (ii) without pre-treatment, were assessed using mass-energy balance and the corresponding greenhouse gas (GHG) emissions. For a digestion period of 30 days, volatile solids degradation of the control sludge and the ultrasonicated secondary sludge was 51.4% and 60.1%, respectively. Mass balance revealed that the quantity of digestate required for dewatering, transport and land application was the lowest (20.2 × 10(6) g dry sludge/day) for ultrasonicated secondary sludge at 31.4 g TS/L. Furthermore, for ultrasonicated secondary sludge at 31.4 g TS/L, the maximum net energy (energy output - energy input) of total dry solids (TDS) was 7.89 × 10(-6) kWh/g and the energy ratio (output/input) was 1.0. GHG emissions were also reduced with an increase in the sludge solids concentration (i.e., 40.0 g TS/L < 30.0 g TS/L < 20.0 g TS/L). Ultrasonication pre-treatment proved to be efficient and beneficial for enhancing anaerobic digestion efficiency of the secondary sludge when compared to the primary and mixed sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Interactions between solid surfaces mediated by polyethylene oxide polymers: effect of polymer concentration. (United States)

    Wei, Xiaoling; Gong, Xiangjun; Ngai, To


    Using total internal reflection microscopy (TIRM), we have systematically measured the interactions between a microsphere and a flat hydrophilic surface in the presence of polyethylene oxide (PEO) polymer solution. Our results reveal that PEO significantly mediates the interaction forces between the two surfaces. At low polymer concentration, the interactions between two surfaces in the presence of PEO are mainly dominated by repulsive forces, originating from diffuse layer overlap. At intermediate polymer concentration, a long-range and weak attraction sets in. This force is likely attributed to the depletion attraction due to the presence of free PEO chains in bulk solution; however, a simple hard-sphere AO model fails to precisely describe the attraction. At high polymer concentration where PEO chains overlap, the attraction disappears, and levitation of the microsphere probe is detected. We argue that at this overlapping region, the correlation length of PEO chains is much smaller than the size of single PEO molecule, leading to weakening and disappearing of the depletion attraction. Finally, at very high concentration, oscillatory structural force is obviously found, indicating the significant structural ordering of the PEO chains under confinement.


    A rapid method for estimating polychlorinated biphenyl (PCB) concentrations in contaminated soils and sediments has been developed by coupling static subcritical water extraction with solid-phase microextraction (SPME). Soil, water, and internal standards are placed in a seale...

  11. Solid Liquid Extraction of Phenolic and Flavonoid Compounds from Cotinus coggygria and Concentration by Nanofiltration


    Koleva, V.; Simeonov, E


    Extraction kinetics of polyphenols and flavonoids from plant material and their separation and concentration by nanofiltration were investigated. The kinetics experiments were carried out with Cotinus coggygria. The influence of the extraction solvent on the extraction rate was defined. Four different extraction solvents or mixtures were applied – methanol, azeotropic ethanol, 50/50 ethanol/water mixture, and pure water. The optimum extraction rate of flavonoids and polyphenols was achieved b...

  12. Effects of spray-drying and choice of solid carriers on concentrations of Labrasol® and Transcutol® in solid self-microemulsifying drug delivery systems (SMEDDS). (United States)

    Li, Liang; Yi, Tao; Lam, Christopher Wai-Kei


    Solid self-microemulsifying drug delivery systems (SMEDDS) have been used increasingly for improving the bioavailability of hydrophobic drugs. Labrasol® and Transcutol® are used widely as surfactant and solubilizer in the formulation of solid SMEDDS. We investigated the effects of spray-drying and the use of different solid carriers on concentrations of Labrasol® and Transcutol® in solid SMEDDS with scutellarin as the formulated drug. Liquid and gas chromatography tandem mass spectrometry (LC-MS and GC-MS) methods were developed for measuring low concentrations of Labrasol® and Transcutol®. In the preparation of solid SMEDDS, lactose, hydroxypropylmethyl cellulose (HPMC) and microcrystalline cellulose (MCC) were used as solid carriers. Judging from the retention ratios of Labrasol® and Transcutol®, the droplet size of solid SMEDDS increased after spray-drying of liquid SMEDDS, and concentrations of these excipients decreased after the solidifying procedure. In such reduction, Lactose and HPMC were found to preserve Labrasol® and Transcutol® better than MCC during spray-drying, and the resultant droplet sizes were smaller than that of MCC. Labrasol® and Transcutol® showed good thermal stability at 60 °C degree for 10 days. It can be concluded that spray-drying could increase the droplet size of solid SMEDDS and decreased the concentration of Labrasol® and Transcutol® therein, while water-soluble solid carriers could preserve Labrasol® and Transcutol® better than insoluble carriers in the solid SMEDDS.

  13. Effects of Spray-Drying and Choice of Solid Carriers on Concentrations of Labrasol® and Transcutol® in Solid Self-Microemulsifying Drug Delivery Systems (SMEDDS

    Directory of Open Access Journals (Sweden)

    Christopher Wai-Kei Lam


    Full Text Available Solid self-microemulsifying drug delivery systems (SMEDDS have been used increasingly for improving the bioavailability of hydrophobic drugs. Labrasol® and Transcutol® are used widely as surfactant and solubilizer in the formulation of solid SMEDDS. We investigated the effects of spray-drying and the use of different solid carriers on concentrations of Labrasol® and Transcutol® in solid SMEDDS with scutellarin as the formulated drug. Liquid and gas chromatography tandem mass spectrometry (LC-MS and GC-MS methods were developed for measuring low concentrations of Labrasol® and Transcutol®. In the preparation of solid SMEDDS, lactose, hydroxypropylmethyl cellulose (HPMC and microcrystalline cellulose (MCC were used as solid carriers. Judging from the retention ratios of Labrasol® and Transcutol®, the droplet size of solid SMEDDS increased after spray-drying of liquid SMEDDS, and concentrations of these excipients decreased after the solidifying procedure. In such reduction, Lactose and HPMC were found to preserve Labrasol® and Transcutol® better than MCC during spray-drying, and the resultant droplet sizes were smaller than that of MCC. Labrasol® and Transcutol® showed good thermal stability at 60 °C degree for 10 days. It can be concluded that spray-drying could increase the droplet size of solid SMEDDS and decreased the concentration of Labrasol® and Transcutol® therein, while water-soluble solid carriers could preserve Labrasol® and Transcutol® better than insoluble carriers in the solid SMEDDS.

  14. Formation of Reversible Solid Electrolyte Interface on Graphite Surface from Concentrated Electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Dongping; Tao, Jinhui; Yan, Pengfei; Henderson, Wesley A.; Li, Qiuyan; Shao, Yuyan; Helm, Monte L.; Borodin, Oleg; Graff, Gordon L.; Polzin, Bryant; Wang, Chong-Min; Engelhard, Mark; Zhang, Ji-Guang; De Yoreo, James J.; Liu, Jun; Xiao, Jie


    Interfacial phenomena have always been key determinants for the performance of energy storage technologies. The solid electrolyte interfacial (SEI) layer, pervasive on the surfaces of battery electrodes for numerous chemical couples, directly affects the ion transport, charge transfer and lifespan of the entire energy system. Almost all SEI layers, however, are unstable resulting in the continuous consumption of the electrolyte. Typically, this leads to the accumulation of degradation products on/restructuring of the electrode surface and thus increased cell impedance, which largely limits the long-term operation of the electrochemical reactions. Herein, a completely new SEI formation mechanism has been discovered, in which the electrolyte components reversibly self-assemble into a protective surface coating on a graphite electrode upon changing the potential. In contrast to the established wisdom regarding the necessity of employing the solvent ethylene carbonate (EC) to form a protective SEI layer on graphite, a wide range of EC-free electrolytes are demonstrated for the reversible intercalation/deintercalation of Li+ cations within a graphite lattice, thereby providing tremendous flexibility in electrolyte tailoring for battery couples. This novel finding is broadly applicable and provides guidance for how to control interfacial reactions through the relationship between ion aggregation and solvent decomposition at polarized interfaces.

  15. Seasonal trends of benzo(apyrene in suspended particulate matter in urban areas of Belgrade, Serbia

    Directory of Open Access Journals (Sweden)

    Snežana Matić-Besarabić


    Full Text Available Polycyclic aromatic hydrocarbons (PAHs were identified to be one of the major toxic air pollutants in urban environment. PAHs are mostly formed during incomplete combustion or pyrolysis of organic material. According to Serbian National Legislation, benzo(apyrene (BaP concentration in total suspended particles (TSP in ambient air in the Belgrade metropolitan area has been determined in the last ten years, as a part of a local air pollution monitoring program performed by the Public Health Institute of Belgrade and funded by Belgrade’s Municipality. Air samples for analysis of BaP in suspended particleshave been collected (as 24 h sample once per month at selected onitoring sites within the municipal air quality monitoring network. At the beginning, according to National Regulation, all samples were taken as total suspended particles (TSP. Since mid-2008, the procedure of sampling methodology was harmonized with EU requirements and solid fraction PM10 has been collected and analyzed using GC/MS. In this study, we have analyzed results of TSP collected between 2005 and 2008. Looking through the results obtained during the period of a whole year, it can be noticed that concentrations of BaP were much higher during winter season at almost all measuring sites.

  16. Using solid-phase microextraction to determine partition coefficients to humic acids and bioavailable concentrations of hydrophobic chemicals

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, E.U.; Meijer, S.N.; Vaes, W.H.J.; Verhaar, H.J.M.; Hermens, J.L.M. [Utrecht Univ. (Netherlands). Research Inst. of Toxicology


    In the current study, the suitability of negligible depletion solid-phase microextraction (nd-SPME) to determine free fractions of chemicals in aquatic environments was explored. The potential interferences of the dissolved matrix (i.e., humic acids) with the SPME measurements were tested. Results show that nd-SPME measures only the freely dissolved fraction and that the measurements are not disturbed by the humic acids. In addition, nd-SPME was used to determine partition coefficients between dissolved organic carbon and water for four hydrophobic chemicals. Obtained values are in excellent agreement with previously reported data. Finally, the bioaccumulation of hexachlorobenzene and PCB 77 to Daphnia magna was determined in the presence and absence of humic acids. The bioconcentration factors (BCF) were calculated based on total as well as on free concentration. Lower BCF values are obtained in the presence of humic acids using total concentrations, whereas equal BCFs are found using free concentrations measured with nd-SPME. Therefore, the authors can conclude that negligible depletion SPME is a good technique to determine bioavailable concentrations of hydrophobic chemicals in aquatic environments.

  17. Remoção de sólidos suspensos na água de irrigação utilizando mantas sintéticas não tecidas Removal of suspended solids in irrigation water utilizing non-woven synthetic fabrics

    Directory of Open Access Journals (Sweden)

    Marcos E. Scatolini


    Full Text Available Com vistas à eficiência de remoção de sólidos em suspensão, quando utilizados em filtros para irrigação localizada, empregaram-se três tipos diferentes de manta sintética não tecida, além de elemento de tela e de disco. Como resultado, as mantas tiveram desempenho superior, ou seja, 27 a 29% de remoção de sólidos em suspensão, enquanto os elementos de tela e disco apresentaram apenas 19 a 20%; contudo, dentre as três mantas avaliadas não foram observadas diferenças significativas, o mesmo ocorrendo entre os elementos de tela e disco.The objective of this work was to verify the efficiency of trickle irrigation filters on the removal of suspended solids using as filter elements three different types of non-woven synthetic fabrics. Also, was conducted an experiment with disk and screen elements in order to compare with the non woven synthetic fabric element. The results have demonstrated that non-woven synthetic fabrics presented better performance, removing 27 to 29% of suspended solids, while screen and disk elements presented 19 to 20% removal. No significant differences were observed among the three fabrics evaluated as well as between the screen and disk elements

  18. Quantification of Surface Suspended Sediments along a River Dominated Coast with NOAA AVHRR and SeaWiFS Measurements: Louisiana, USA (United States)

    Myint, S. W.; Walker, N. D.


    The ability to quantify suspended sediment concentrations accurately over both time and space using satellite data has been a goal of many environmental researchers over the past few decades This study utilizes data acquired by the NOAA Advanced Very High Resolution Radiometer (AVHRR) and the Orbview-2 Sea-viewing wide field-of-view (SeaWiFS) ocean colour sensor, coupled with field measurements to develop statistical models for the estimation of near-surface suspended sediment and suspended solids "Ground truth" water samples were obtained via helicopter, small boat and automatic water sampler within a few hours of satellite overpasses The NOAA AVHRR atmospheric correction was modified for the high levels of turbidity along the Louisiana coast. Models were developed based on the field measurements and reflectance/radiance measurements in the visible and near infrared Channels of NOAA-14 and Orbview-2 SeaWiFS. The best models for predicting surface suspended sediment concentrations were obtained with a NOAA AVHRR Channel 1 (580-680nm) cubic model, Channel 2 (725-1100 nm) linear mod$ and SeaWiFs Channel 6 (660-68Onm) power modeL The suspended sediment models developed using SeaWiFS Channel 5 (545-565 nm) were inferior, a result that we attribute mainly to the atmospheric correction technique, the shallow depth of the water samples and absorption effects from non-sediment water constituents.

  19. Suspended sediments limit coral sperm availability (United States)

    Ricardo, Gerard F.; Jones, Ross J.; Clode, Peta L.; Humanes, Adriana; Negri, Andrew P.


    Suspended sediment from dredging activities and natural resuspension events represent a risk to the reproductive processes of coral, and therefore the ongoing maintenance of reefal populations. To investigate the underlying mechanisms that could reduce the fertilisation success in turbid water, we conducted several experiments exposing gametes of the corals Acropora tenuis and A. millepora to two sediment types. Sperm limitation was identified in the presence of siliciclastic sediment (230 and ~700 mg L−1), with 2–37 fold more sperm required to achieve maximum fertilisation rates, when compared with sediment-free treatments. This effect was more pronounced at sub-optimum sperm concentrations. Considerable (>45%) decreases in sperm concentration at the water’s surface was recorded in the presence of siliciclastic sediment and a >20% decrease for carbonate sediment. Electron microscopy then confirmed sediment entangled sperm and we propose entrapment and sinking is the primary mechanism reducing sperm available to the egg. Longer exposure to suspended sediments and gamete aging further decreased fertilisation success when compared with a shorter exposure. Collectively, these findings demonstrate that high concentrations of suspended sediments effectively remove sperm from the water’s surface during coral spawning events, reducing the window for fertilisation with potential subsequent flow-on effects for recruitment. PMID:26659008

  20. Multidrug, Anti-HIV Amorphous Solid Dispersions: Nature and Mechanisms of Impacts of Drugs on Each Other's Solution Concentrations. (United States)

    Arca, Hale Çiğdem; Mosquera-Giraldo, Laura I; Dahal, Durga; Taylor, Lynne S; Edgar, Kevin J


    Drug therapy has been instrumental in prolonging the lives of patients infected by human immunodeficiency virus (HIV). In order to combat development of resistance, therapies involving three or more drugs in combination are recommended by the World Health Organization (WHO) to suppress HIV and prevent development of acquired immune deficiency syndrome (AIDS). It is desirable for multidrug combinations to be coformulated into single dosage forms where possible, to promote patient convenience and adherence to dosage regimens, for which amorphous solid dispersion (ASD) is particularly well-suited. We investigated multidrug ASDs of three model anti-HIV drugs, ritonavir (Rit), etravirine (Etra), and efavirenz (Efa), in cellulosic polymer matrices. We hypothesized that the presence of multiple drugs would reduce crystallization tendency, thereby providing stable, supersaturating formulations for bioavailability enhancement. We explored new ASD polymers including cellulose acetate suberate (DSSub 0.9, CASub) and cellulose acetate adipate propionate (DSAd 0.9, CAAdP), and control commercial cellulosic polymers including 6-carboxycellulose acetate butyrate (CCAB) and carboxymethyl cellulose acetate butyrate (CMCAB). We succeeded in preparing three-drug ASDs containing very high drug loadings (45% drug total; 15% of each drug); each polymer tested was effective at stabilizing the amorphous drugs in the solid phase, as demonstrated by XRD, SEM, and DSC studies. In pH 6.8 dissolution studies ASDs released each anti-HIV drug over 8 h, affording supersaturated solutions of each drug, but unexpectedly failing in some cases to reach maximum possible supersaturation. In a second set of dissolution studies (pH 6.8), the cause of the observed solution concentration limitations was investigated by studying release from single- and two-drug ASDs. Concentrations of Rit, Etra, and Efa achieved from three-drug ASDs were higher than those achieved from crystalline drugs. Surprisingly

  1. Turbidity and suspended solids in the runoff susceptible of use for the artificial recharge of the deep granular aquifer subjacent to the town of San Luis de Potosi (Mexico); Turbidez y solidos en suspension de las aguas de escorrentia susceptibles de ser utilizadas en la recarga artificial del acuifero granular profundo subyacente a la ciudad de San Luis de Potosi (Mexico)

    Energy Technology Data Exchange (ETDEWEB)

    Murillo, J. M.


    This article presents an analysis of the turbidity and solid contents in suspension of the runoff that might be used for artificially recharging a deep granular aquifer located by San Luis de Potosi. The programmed artificial recharge operation corresponds to a type known as Aquifer Storage and Recovery (ASR). A series of equations to correlate the solids in suspension with turbidity and its validity are put forth. Reference is also made to the maximum content in suspended solids that operations of USR-type recharge can assume. Through this analysis, we were able to corroborate that turbidity varies over time according to an exponential function of the decreasing type, which accounts both for the deposition of particles that sediment exclusively due to the effect of gravity, and the action of certain mechanisms that favour coagulation and the natural flocculation of colloidal particles. Given that the operations of artificial recharge by means of USR require very rigorous conditions, in terms of the maximum contents of solids in suspension, the analysis has also been carried out for surface installations such as infiltration ponds. (Author) 24 refs.

  2. Final Technical Report: Using Solid Particles as Heat Transfer Fluid for use in Concentrating Solar Power (CSP) Plants

    Energy Technology Data Exchange (ETDEWEB)

    Lattanzi, Aaron [Univ. of Colorado, Boulder, CO (United States); Hrenya, Christine [Univ. of Colorado, Boulder, CO (United States)


    In today’s industrial economy, energy consumption has never been higher. Over the last 15 years the US alone has consumed an average of nearly 100 quadrillion BTUs per year [21]. A need for clean and renewable energy sources has become quite apparent. The SunShot Initiative is an ambitious effort taken on by the United States Department of Energy that targets the development of solar energy that is cost-competitive with other methods for generating electricity. Specifically, this work is concerned with the development of concentrating solar power plants (CSPs) with granular media as the heat transfer fluid (HTF) from the solar receiver. Unfortunately, the prediction of heat transfer in multiphase flows is not well understood. For this reason, our aim is to fundamentally advance the understanding of multiphase heat transfer, particularly in gas-solid flows, while providing quantitative input for the design of a near black body receiver (NBB) that uses solid grains (like sand) as the HTF. Over the course of this three-year project, a wide variety of contributions have been made to advance the state-of-the art description for non-radiative heat transfer in dense, gas-solid systems. Comparisons between a state-of-the-art continuum heat transfer model and discrete element method (DEM) simulations have been drawn. The results of these comparisons brought to light the limitations of the continuum model due to inherent assumptions in its derivation. A new continuum model was then developed for heat transfer at a solid boundary by rigorously accounting for the most dominant non-radiative heat transfer mechanism (particle-fluid-wall conduction). The new model is shown to be in excellent agreement with DEM data and captures the dependence of heat transfer on particle size, a dependency that previous continuum models were not capable of. DEM and the new continuum model were then employed to model heat transfer in a variety of receiver geometries. The results provided crucial

  3. Contribution of solid fuel, gas combustion, or tobacco smoke to indoor air pollutant concentrations in Irish and Scottish homes

    Energy Technology Data Exchange (ETDEWEB)

    Semple, S.; Garden, C. (Univ. of Aberdeen. Scottish Centre for Indoor Air, Div. of Applied Health Sciences (United Kingdom)); Galea, K.S.; Cowie, H.; Hurley, J.F.; Sanchez-Jimenez, A. (Scottish Centre for Indoor Air. Institute of Occupational Medicine, Edinburgh (United Kingdom)); Whelan, P.; Coggins, M. (National Univ. of Ireland Galway (Ireland)); Thorne, P.S. (Univ. of Iowa. Environmental Health Sciences Research Center, Iowa City, IA (United States)); Ayres, J.G. (Univ. of Birmingham. Institute of Occupational and Environmental Medicine (United Kingdom))


    There are limited data describing pollutant levels inside homes that burn solid fuel within developed country settings with most studies describing test conditions or the effect of interventions. This study recruited homes in Ireland and Scotland where open combustion processes take place. Open combustion was classified as coal, peat, or wood fuel burning, use of a gas cooker or stove, or where there is at least one resident smoker. Twenty-four-hour data on airborne concentrations of particulate matter <2.5 mu in size (PM{sub 2.5}), carbon monoxide (CO), endotoxin in inhalable dust and carbon dioxide (CO{sub 2}), together with 2-3 week averaged concentrations of nitrogen dioxide (NO{sub 2}) were collected in 100 houses during the winter and spring of 2009-2010. The geometric mean of the 24-h time-weighted-average (TWA) PM{sub 2.5} concentration was highest in homes with resident smokers (99 mu/m3- much higher than the WHO 24-h guidance value of 25 mu/m3). Lower geometric mean 24-h TWA levels were found in homes that burned coal (7 mu/m3) or wood (6 mu/m3) and in homes with gas cookers (7 mu/m3). In peat-burning homes, the average 24-h PM{sub 2.5} level recorded was 11 mu/m3. Airborne endotoxin, CO, CO{sub 2}, and NO{sub 2} concentrations were generally within indoor air quality guidance levels. (Author)

  4. Species sensitivity distributions for suspended clays, sediment burial, and grain size change in the marine environment. (United States)

    Smit, Mathijs G D; Holthaus, Karlijn I E; Trannum, Hilde C; Neff, Jerry M; Kjeilen-Eilertsen, Grete; Jak, Robbert G; Singsaas, Ivar; Huijbregts, Mark A J; Hendriks, A Jan


    Assessment of the environmental risk of discharges, containing both chemicals and suspended solids (e.g., drilling discharges to the marine environment), requires an evaluation of the effects of both toxic and nontoxic pollutants. To date, a structured evaluation scheme that can be used for prognostic risk assessments for nontoxic stress is lacking. In the present study we challenge this lack of information by the development of marine species sensitivity distributions (SSDs) for three nontoxic stressors: suspended clays, burial by sediment, and change in sediment grain size. Through a literature study, effect levels were obtained for suspended clays, as well as for burial of biota. Information on the species preference range for median grain size was used to assess the sensitivity of marine species to changes in grain size. The 50% hazardous concentrations (HC50) for suspended barite and bentonite based on 50% effect concentrations (EC50s) were 3,010 and 1,830 mg/L, respectively. For burial the 50% hazardous level (HL50) was 5.4 cm. For change in median grain size, two SSDs were constructed; one for reducing and one for increasing the median grain size. The HL50 for reducing the median grain size was 17.8 mum. For increasing the median grain size this value was 305 mum. The SSDs have been constructed by using information related to offshore oil- and gas-related activities. Nevertheless, the results of the present study may have broader implications. The hypothesis of the present study is that the SSD methodology developed for the evaluation of toxic stress can also be applied to evaluate nontoxic stressors, facilitating the incorporation of nontoxic stressors in prognostic risk assessment tools.

  5. Tidal influence on suspended sediment distribution and dispersal in the northern Andaman Sea and Gulf of Martaban

    Digital Repository Service at National Institute of Oceanography (India)

    Ramaswamy, V.; Rao, P.S.; Rao, K.H.; Thwin, S.; Rao, N.S.; Raiker, V.

    Surface and water column profiles of suspended matter collected during April-May 2002, and satellite images were used to study factors influencing suspended sediment concentrations (SSCs) and dispersal in the northern Andaman Sea and Gulf...

  6. Identifying and overcoming the effect of mass transfer limitation on decreased yield in enzymatic hydrolysis of lignocellulose at high solid concentrations. (United States)

    Du, Jian; Cao, Yuan; Liu, Guodong; Zhao, Jian; Li, Xuezhi; Qu, Yinbo


    Cellulose conversion decreases significantly with increasing solid concentrations during enzymatic hydrolysis of insoluble lignocellulosic materials. Here, mass transfer limitation was identified as a significant determining factor of this decrease by studying the hydrolysis of delignified corncob residue in shake flask, the most used reaction vessel in bench scale. Two mass transfer efficiency-related factors, mixing speed and flask filling, were shown to correlate closely with cellulose conversion at solid loadings higher than 15% DM. The role of substrate characteristics in mass transfer performance was also significant, which was revealed by the saccharification of two corn stover substrates with different pretreatment methods at the same solid loading. Several approaches including premix, fed-batch operation, and particularly the use of horizontal rotating reactor were shown to be valid in facilitating cellulose conversion via improving mass transfer efficiency at solid concentrations higher than 15% DM. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Characteristics of sediment data and annual suspended-sediment loads and yields for selected lower Missouri River mainstem and tributary stations, 1976-2008 (United States)

    Heimann, David C.; Rasmussen, Patrick P.; Cline, Teri L.; Pigue, Lori M.; Wagner, Holly R.


    Suspended-sediment data from 18 selected surface-water monitoring stations in the lower Missouri River Basin downstream from Gavins Point Dam were used in the computation of annual suspended-sediment and suspended-sand loads for 1976 through 2008. Three methods of suspended-sediment load determination were utilized and these included the subdivision method, regression of instantaneous turbidity with suspended-sediment concentrations at selected stations, and regression techniques using the Load Estimator (LOADEST) software. Characteristics of the suspended-sediment and streamflow data collected at the 18 monitoring stations and the tabulated annual suspended-sediment and suspended-sand loads and yields are presented.

  8. A space-charge treatment of the increased concentration of reactive species at the surface of a ceria solid solution

    Energy Technology Data Exchange (ETDEWEB)

    Zurhelle, Alexander F.; Souza, Roger A. de [Institute of Physical Chemistry, RWTH Aachen University (Germany); Tong, Xiaorui; Mebane, David S. [Department of Mechanical and Aerospace Engineering, West Virginia University, Morgantown, WV (United States); Klein, Andreas [Institute of Materials Science, TU Darmstadt (Germany)


    A space-charge theory applicable to concentrated solid solutions (Poisson-Cahn theory) was applied to describe quantitatively as a function of temperature and oxygen partial pressure published data obtained by in situ X-ray photoelectron spectroscopy (XPS) for the concentration of Ce{sup 3+} (the reactive species) at the surface of the oxide catalyst Ce{sub 0.8}Sm{sub 0.2}O{sub 1.9}. In contrast to previous theoretical treatments, these calculations clearly indicate that the surface is positively charged and compensated by an attendant negative space-charge zone. The high space-charge potential that develops at the surface (>0.8 V) is demonstrated to be hardly detectable by XPS measurements because of the short extent of the space-charge layer. This approach emphasizes the need to take into account defect interactions and to allow deviations from local charge neutrality when considering the surfaces of oxide catalysts. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Characterization of Solid Dispersion of Itraconazole Prepared by Solubilization in Concentrated Aqueous Solutions of Weak Organic Acids and Drying. (United States)

    Parikh, Tapan; Sandhu, Harpreet K; Talele, Tanaji T; Serajuddin, Abu T M


    The purpose of this study was to develop an amorphous solid dispersion (SD) of an extremely water-insoluble and very weakly basic drug, itraconazole (ITZ), by interaction with weak organic acids and then drying that would enhance dissolution rate of drug and physical stability of formulation. Aqueous solubility of ITZ in concentrated solutions of weak organic acids, such as glutaric, tartaric, malic and citric acid, was determined. Solutions with high drug solubility were dried using vacuum oven and the resulting SDs having 2 to 20% drug load were characterized by differential scanning calorimetry (DSC), powder X-ray diffractometry (PXRD) and attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy. The dissolution of SDs was initially studied in 250 mL of 0.1 N HCl (pH 1.1), and any undissolved solids were collected and analyzed by PXRD. The pH of the dissolution medium was then changed from 1.1 to 5.5, particle size of precipitates were measured, and drug concentrations in solution were determined by filtration through membrane filters of varying pore sizes. The aqueous solubility of ITZ was greatly enhanced in presence of weak acids. While the solubility of ITZ in water was ~4 ng/ mL, it increased to 25-40 mg per g of solution at 25°C and 200 mg per g of solution at 65°C at a high acid concentration leading to extremely high solubilization. PXRD of SDs indicated that ITZ was present in the amorphous form, wherein the acid formed a partially crystalline matrix. ATR-FTIR results showed possible weak interactions, such as hydrogen bonding, between drug and acid but there was no salt formation. SDs formed highly supersaturated solutions at pH 1.1 and had superior dissolution rate as compared to amorphous drug and physical mixtures of drug and acids. Following the change in pH from 1.1 to 5.5, ITZ precipitated as mostly nanoparticles, providing high surface area for relatively rapid redissolution. A method of highly solubilizing an

  10. Effects of Suspended Sediment on Early Life Stages of Smallmouth Bass (Micropterus dolomieu). (United States)

    Suedel, Burton C; Wilkens, Justin L; Kennedy, Alan J


    The resuspension of sediments caused by activities, such as dredging operations, is a concern in Great Lakes harbors where multiple fish species spawn. To address such concerns, smallmouth bass (Micropterus dolomieu) were exposed to uncontaminated suspended sediment (nominally 0, 100, 250, and 500 mg/L) continuously for 72 h to determine the effects on egg-hatching success and swim-up fry survival and growth. The test sediments were collected from two harbors: (1) fine-grained sediment in Grand Haven Harbor, Lake Michigan, and (2) coarser-grained sediment in Fairport Harbor, Lake Erie. Eggs exposed to total suspended solids (TSS) concentrations >100 mg/L resulted in decreased survival of post-hatch larval fish. Fry survival was >90 % at the highest exposure concentration (500 mg/L), but growth was decreased when the exposure concentration was >100 mg/L. Growth and survival of swim-up fry held for a 7- and 26-day post-exposure the grow-out period was variable suggesting that the sediment grain size and strain of fish may influence lingering effects after the cessation of exposure. The results suggest that exposed eggs hatched normally; however, newly hatched larvae, which are temporarily immobile, are more vulnerable to the effects of suspended sediment. The swim-up fry were found to be more sensitive to high TSS concentrations in sandy relative to silty sediment. These data represent a conservative exposure scenario that can be extrapolated to high-energy systems in the field to inform management decisions regarding the necessity for dredging windows or need to implement controls to protect M. dolomieu.

  11. An Integrated Instrumentation System for Velocity, Concentration and Mass Flow Rate Measurement of Solid Particles Based on Electrostatic and Capacitance Sensors

    Directory of Open Access Journals (Sweden)

    Jian Li


    Full Text Available The online and continuous measurement of velocity, concentration and mass flow rate of pneumatically conveyed solid particles for the high-efficiency utilization of energy and raw materials has become increasingly significant. In this paper, an integrated instrumentation system for the velocity, concentration and mass flow rate measurement of dense phase pneumatically conveyed solid particles based on electrostatic and capacitance sensorsis developed. The electrostatic sensors are used for particle mean velocity measurement in combination with the cross-correlation technique, while the capacitance sensor with helical surface-plate electrodes, which has relatively homogeneous sensitivity distribution, is employed for the measurement of particle concentration and its capacitance is measured by an electrostatic-immune AC-based circuit. The solid mass flow rate can be further calculated from the measured velocity and concentration. The developed instrumentation system for velocity and concentration measurement is verified and calibrated on a pulley rig and through static experiments, respectively. Finally the system is evaluated with glass beads on a gravity-fed rig. The experimental results demonstrate that the system is capable of the accurate solid mass flow rate measurement, and the relative error is within −3%–8% for glass bead mass flow rates ranging from 0.13 kg/s to 0.9 kg/s.

  12. Development of an Integrated Suspended Sediment Sampling System - Prototype Results (United States)

    Nerantzaki, Sofia; Moirogiorgou, Konstantia; Efstathiou, Dionissis; Giannakis, George; Voutsadaki, Stella; Zervakis, Michalis; Sibetheros, Ioannis A.; Zacharias, Ierotheos; Karatzas, George P.; Nikolaidis, Nikolaos P.


    The Mediterranean region is characterized by a unique micro-climate and a complex geologic and geomorphologic environment caused by its position in the Alpine orogenesis belt. Unique features of the region are the temporary rivers that are dry streams or streams with very low flow for most of the time over decadal time scales. One of their key characteristics is that they present flashy hydrographs with response times ranging from minutes to hours. It is crucial to monitor flash-flood events and observe their behavior since they can cause environmental degradation of the river's wider location area. The majority of sediment load is transferred during these flash events. Quantification of these fluxes through the development of new measuring devices is of outmost importance as it is the first step for a comprehensive understanding of the water quality, the soil erosion and erosion sources, and the sediment and nutrient transport routes. This work proposes an integrated suspended sediment sampling system which is implemented in a complex semi-arid Mediterranean watershed (i.e. the Koiliaris River Basin of Crete) with temporary flow tributaries and karstic springs. The system consists of sensors monitoring water stage and turbidity, an automated suspended sediment sampler, and an online camera recording video sequence of the river flow. Water stage and turbidity are continuously monitored and stage is converted to flow with the use of a rating curve; when either of these variables exceeds certain thresholds, the pump of the sediment sampler initiates sampling with a rotation proportional to the stage (flow weighted sampling). The water passes through a filter that captures the sediment, the solids are weighted after each storm and the data are converted to a total sediment flux. At the same time, the online camera derives optical measurements for the determination of the two-dimensional river flow velocity and the spatial sediment distribution by analyzing the Hue

  13. Progression towards optimization of viscosity of highly concentrated carbonaceous solid-water slurries by incorporating and modifying surface chemistry parameters with and without additives (United States)

    Mukherjee, Amrita

    Carbonaceous solid-water slurries (CSWS) are concentrated suspensions of coal, petcoke bitumen, pitch etc. in water which are used as feedstock for gasifiers. The high solid loading (60-75 wt.%) in the slurry increases CSWS viscosity. For easier handling and pumping of these highly loaded mixtures, low viscosities are desirable. Depending on the nature of the carbonaceous solid, solids loading in the slurry and the particle size distribution, viscosity of a slurry can vary significantly. Ability to accurately predict the viscosity of a slurry will provide a better control over the design of slurry transport system and for viscosity optimization. The existing viscosity prediction models were originally developed for hard-sphere suspensions and therefore do not take into account surface chemistry. As a result, the viscosity predictions using these models for CSWS are not very accurate. Additives are commonly added to decrease viscosity of the CSWS by altering the surface chemistry. Since additives are specific to CSWS, selection of appropriate additives is crucial. The goal of this research was to aid in optimization of CSWS viscosity through improved prediction and selection of appropriate additive. To incorporate effect of surface chemistry in the models predicting suspension viscosity, the effect of the different interfacial interactions caused by different surface chemistries has to be accounted for. Slurries of five carbonaceous solids with varying O/C ratio (to represent different surface chemistry parameters) were used for the study. To determine the interparticle interactions of the carbonaceous solids in water, interfacial energies were calculated on the basis of surface chemistries, characterized by contact angles and zeta potential measurements. The carbonaceous solid particles in the slurries were assumed to be spherical. Polar interaction energy (hydrophobic/hydrophilic interaction energy), which was observed to be 5-6 orders of magnitude higher than the

  14. Solid-state 51V MAS NMR spectroscopy determines component concentration and crystal phase in co-crystallised mixtures of vanadium complexes

    DEFF Research Database (Denmark)

    Nielsen, Ulla Gro; Hazell, Alan Charles; Skibsted, Jørgen Bengaard


    resonances are sensitive to intermolecular interactions specific to each crystal phase. The solid-state V-51 MAS NMR spectroscopic data show that the different phases do not co-precipitate but the concentration of the solute (which can be either 1 or 2) can vary. Thus co-crystallised mixtures of 1 and 2 can...


    Directory of Open Access Journals (Sweden)

    Sorin Anghel


    Full Text Available Sedimentation of suspensions process is important, especially in pollution and biologic studies. Unlike usual methods,as those using pipettes, aerometer or balances, the optical ones are nondestructive and more accurate. During thesedimentation produced by the braked fall off the solid particles in suspension, fluctuations induced by an oppositevertical diffusion occur. We used a scattering method, based on the attenuation of a laser beam, which allows plottingsedimentation curves (the dependence on time of the suspended solid particles concentration of the process. Weobtained an empirical relation describing sedimentation curves as a function of some main parameters (related toinitial concentration, height in suspension, dimensions of suspended solid particles and we performed a simulation ofthe experimental sedimentation curves using the obtained relation and Mathcad software facilities. We notice that theresults of these studies allow using a fast method in order to determine the sedimentation time, which often can be verylong.

  16. Biological nutrient and organic removal from meat packing wastewater with a unique sequence of suspended growth and fixed-film reactors. (United States)

    Lim, S J; Kim, S H; Fox, P


    A unique sequence of anaerobic filter/suspended anaerobic/aerobic (AO) reactor/aerobic filter system was developed to alleviate the drawbacks of conventional suspended growth and fixed growth systems. An anaerobic filter (AF) was used to efficiently produce volatile fatty acids (VFAs) prior to the aerobic suspended growth. A second anaerobic reactor was installed in the A/O return activated sludge line to improve phosphorus uptake by potentially controlling glycogen accumulating organisms (GAOs). One biological aerobic filter (BAF) was used for nitrification followed by an anoxic filter for denitrification and a second BAF was used for effluent polishing. The meat packing wastewater had a biochemical oxygen demand (BOD) of 853 mg/L and total nitrogen (T-N) and total phosphorus (T-P) concentrations of 61.1 mg/L and 5.8 mg/L, respectively. The BOD removal efficiency was 99.0-99.7% and the suspended solids (SS) concentration in the effluent was below 10 mg/L. The T-N removal efficiency was maintained at greater than 75.0% except at low C/N ratios. A high T-P removal efficiency, 74.7-83.9%, was also obtained when the system was operated at a hydraulic retention time of 15.7 hrs. The AF successfully produced VFAs that aided in phosphorus removal. Additionally, recycled concrete aggregate used as attachment media in the biological filters continuously provided micronutrients and stabilized the pH.

  17. Evaluating the Performance of the Mixture Model Coupled with High and Low Reynolds Turbulence Closures in the Numerical Description of Concentrated Solid-Liquid Flows of Settling Particles

    Directory of Open Access Journals (Sweden)

    R. Silva


    Full Text Available In this manuscript, Computational Fluid Dynamics (CFD studies applying the Mixture Model coupled with both a High Reynolds and a Low Reynolds k-ε turbulence closures, were used to describe experimental pressure gradients and particle concentration profiles from the literature, for concentrated solid-liquid flows of settling particles in a horizontal pipe above the critical deposition velocity. With this work a new Mixture Model formulation is presented, incorporating the Jones-Launder Low Reynolds k-ε turbulence closure, to overcome the excessive turbulence production observed in the numerical studies using the High Reynolds k-ε turbulence model. Additionally, this formulation provides a more accurate representation of the wall turbulence damping phenomena, observed in the experimental testing for the flow of higher particle concentrations suspensions and higher flow velocities. Knowledge on the conditions that cause turbulence attenuation on solid-liquid flows is still scarce in the literature and of considerable value for industrial applications.

  18. Simultaneous measurement of local particle movement, solids concentrations and bubble properties in fluidized bed reactors using a novel fiber optical technique

    Energy Technology Data Exchange (ETDEWEB)

    Tayebi, Davoud


    This thesis develops a new method for simultaneous measurements of local flow properties in highly concentrated multiphase flow systems such as gas-solid fluidized bed reactors. The method is based on fiber optical technique and tracer particles. A particle present in the measuring volume in front of the probe is marked with a fluorescent dye. A light source illuminates the particles and the detecting fibres receive reflected light from uncoated particles and fluorescent light from the tracer particle. Using optical filters, the fluorescent light can be distinguished and together with a small fraction of background light from uncoated particles can be used for determination of local flow properties. Using this method, one can simultaneously measure the local movement of a single tracer particle, local bubble properties and the local solids volume fractions in different positions in the bed. The method is independent of the physical properties of the tracer particles. It is also independent of the local solids concentrations in the range of 0 to 60 vol.-%, but is mainly designed for highly concentrated flow systems. A computer programme that uses good signals from at least three sensors simultaneously to calculate the tracer particle velocity in two dimensions have been developed. It also calculates the bubble properties and local solids volume fractions from the same time series. 251 refs., 150 figs., 5 tabs.

  19. Solubility and hydrolysis of Np(V) in dilute to concentrated alkaline NaCl solutions. Formation of Na-Np(V)-OH solid phases at 22 C

    Energy Technology Data Exchange (ETDEWEB)

    Petrov, Vladimir G. [Lomonosov Moscow State Univ. (Russian Federation). Dept. of Chemistry; Fellhauer, David; Gaona, Xavier; Dardenne, Kathy; Rothe, Joerg; Altmaier, Marcus [Karlsruhe Institute of Technology (Germany). Inst. for Nuclear Waste Disposal; Kalmykov, Stepan N. [Lomonosov Moscow State Univ. (Russian Federation). Dept. of Chemistry; NRC Kurchatov Institute, Moscow (Russian Federation)


    The solubility of Np(V) was investigated at T=22±2 C in alkaline NaCl solutions of different ionic strength (0.1-5.0 M). The solid phases controlling the solubility at different -log{sub 10} m{sub H{sup +}}(pH{sub m}) and NaCl concentration were characterized by XRD, quantitative chemical analysis, SEM-EDS and XAFS (both XANES and EXAFS). Aqueous phases in equilibrium with Np(V) solids were investigated for selected samples within 8.9≤pH{sub m}≤10.3 by UV-vis/NIR absorption spectroscopy. In 0.1 M NaCl, the experimental solubility of the initial greenish NpO{sub 2}OH(am) solid phase is in good agreement with previous results obtained in NaClO{sub 4} solutions, and is consistent with model calculations for fresh NpO{sub 2}OH(am) using the thermodynamic data selection in NEA-TDB. Below pH{sub m}∝11.5 and for all NaCl concentrations studied, Np concentration in equilibrium with the solid phase remained constant during the timeframe of this study (∝2 years). This observation is in contrast to the aging of the initial NpO{sub 2}OH(am) into a more crystalline modification with the same stoichiometry, NpO{sub 2}OH(am, aged), as reported in previous studies for concentrated NaClO{sub 4} and NaCl. Instead, the greenish NpO{sub 2}OH(am) transforms into a white solid phase in those systems with [NaCl]≥1.0 M and pH{sub m}≥11.5, and into two different pinkish phases above pH{sub m}∝13.2. The solid phase transformation is accompanied by a drop in Np solubility of 0.5-2 log{sub 10}-units (depending upon NaCl concentration). XANES analyses of green, white and pink phases confirm the predominance of Np(V) in all cases. Quantitative chemical analysis shows the incorporation of Na{sup +} in the original NpO{sub 2}OH(am) material, with Na:Np ≤ 0.3 for the greenish solids and 0.8 ≤ Na:Np ≤ 1.6 for the white and pinkish phases. XRD data confirms the amorphous character of the greenish phase, whereas white and pink solids show well-defined but discrepant XRD patterns

  20. Temperature signal in suspended sediment export from an Alpine catchment (United States)

    Costa, Anna; Molnar, Peter; Stutenbecker, Laura; Bakker, Maarten; Silva, Tiago A.; Schlunegger, Fritz; Lane, Stuart N.; Loizeau, Jean-Luc; Girardclos, Stéphanie


    Suspended sediment export from large Alpine catchments ( > 1000 km2) over decadal timescales is sensitive to a number of factors, including long-term variations in climate, the activation-deactivation of different sediment sources (proglacial areas, hillslopes, etc.), transport through the fluvial system, and potential anthropogenic impacts on the sediment flux (e.g. through impoundments and flow regulation). Here, we report on a marked increase in suspended sediment concentrations observed near the outlet of the upper Rhône River Basin in the mid-1980s. This increase coincides with a statistically significant step-like increase in basin-wide mean air temperature. We explore the possible explanations of the suspended sediment rise in terms of changes in water discharge (transport capacity), and the activation of different potential sources of fine sediment (sediment supply) in the catchment by hydroclimatic forcing. Time series of precipitation and temperature-driven snowmelt, snow cover, and ice melt simulated with a spatially distributed degree-day model, together with erosive rainfall on snow-free surfaces, are tested to explore possible reasons for the rise in suspended sediment concentration. We show that the abrupt change in air temperature reduced snow cover and the contribution of snowmelt, and enhanced ice melt. The results of statistical tests show that the onset of increased ice melt was likely to play a dominant role in the suspended sediment concentration rise in the mid-1980s. Temperature-driven enhanced melting of glaciers, which cover about 10 % of the catchment surface, can increase suspended sediment yields through an increased contribution of sediment-rich glacial meltwater, increased sediment availability due to glacier recession, and increased runoff from sediment-rich proglacial areas. The reduced extent and duration of snow cover in the catchment are also potential contributors to the rise in suspended sediment concentration through

  1. Edible fat structures at high solid fat concentrations: Evidence for the existence of oil-filled nanospaces (United States)

    Peyronel, Fernanda; Quinn, Bonnie; Marangoni, Alejandro G.; Pink, David A.


    We have characterized the surfaces of grain boundaries in edible oils with high solid fat content by combining ultra-small angle x-ray scattering (USAXS) with theoretical modelling and computer simulation. Our results will lead to understand the solid structures formed at the time of manufacturing fats like confectionery fats as well as pave the way for the engineering of innovative fat products. Edible fats are complex semi-solid materials where a solid structure entraps liquid oil. It was not until USAXS combined with modelling was used that the nano- to meso-structures for systems with less than 20% solids were understood. The interpretation of those results utilized models of crystalline nanoplatelets represented by rigid close-packed flat aggregates made of spheres and was allowed to aggregate using the Metropolis Monte Carlo technique. Here, we report on systems containing between 50% and 90% solids. We modelled the solid phase as being formed from seeds onto which solids condensed thereby giving rise to oil-filled nanospaces. The models predicted that the system (a) exhibits structures with fractal dimensions approximately 2, (b) a broad peak somewhat masking that slope, and (c) for smaller values of q, indications that the structures with fractal dimension approximately 2 are uniformly distributed in space. The interpretation of the experimental data was completely driven by these results. The computer simulation predictions were used in conjunction with the USAXS observations to conclude that the systems studied scattered from oil-cavities with sizes between ˜800 and ˜16 000 Å and possessed rough 2-dimensional walls.

  2. A comparison between ultraviolet disinfection and copper alginate beads within a vortex bioreactor for the deactivation of bacteria in simulated waste streams with high levels of colour, humic acid and suspended solids.

    Directory of Open Access Journals (Sweden)

    Simon F Thomas

    Full Text Available We show in this study that the combination of a swirl flow reactor and an antimicrobial agent (in this case copper alginate beads is a promising technique for the remediation of contaminated water in waste streams recalcitrant to UV-C treatment. This is demonstrated by comparing the viability of both common and UV-C resistant organisms in operating conditions where UV-C proves ineffective - notably high levels of solids and compounds which deflect UV-C. The swirl flow reactor is easy to construct from commonly available plumbing parts and may prove a versatile and powerful tool in waste water treatment in developing countries.

  3. Suspended sediment levels and turbidity along the Guadalquivir river related to the hydrological regimes (United States)

    Carpintero García, Miriam; Contreras Arribas, Eva; Jurado Lopez, Alicia; Aguilar Porro, Cristina; José Polo Gómez, María


    In Mediterranean watersheds, soil loss is enhanced by the marked seasonality and torrential character of the rainfall regime, together with the usually predominant agricultural usesd. This fact determines the nature and amount of the discharges to the fluvial network in the Guadalquivir River (Spain), where the dense reservoir network within the contributing areas to the main stream alters the original sediment dynamics, and the transport and deposition patterns along the river, especially in the final stretch. The Guadalquivir River basin is located in southern Spain, with a contributing area of 57500 km2. It is a Mediterranean basin with a mean annual rainfall of 600 mm year-1.The changes of soil uses in the basin are associated with an increase of the irrigated area (in 201290 ha until 2007 upstream) and olive area (in 311115 ha until 2007).The suspended sediment concentration in the river is very high, with extreme values up to 16 g/l in the final stretch, which includes the estuary, associated with persistent turbidity events forced by different combinations of conditions. The solids are very fine- textured due to the great length of the river and, mainly, the extreme trapping efficiency of the dense reservoir network upstream. This work shows the spatial-temporal evolution of the suspended sediment concentration and turbidity regime along the Guadalquivir river and its relation with the different soil uses in the different contribunting areas within the watershed, together with the dependence on the hydrological annual regime. Turbidity trends are estimatedby means of data from Landsat-7 ETM that were validated with the quantified suspended sediment concentration values obtained from both field campaigns and automated monitored control points along the river. The results show a time lag between fluvial contributions and suspended sediment concentration due to the intense regulation in the watershed, that is dependent on the storage capacity upstream, the

  4. Dynamic transport of suspended sediment by solitary wave: Experimental study (United States)

    cho, JaeNam; Kim, DongHyun; Hwang, KyuNam; Lee, SeungOh


    Solitary waves are able to transport a large amount of suspended sediment when approaching on the beach, which sometimes causes - serious beach erosion, especially in the east and south coastal lines in Korea. But it has rarely been known about the method how to evaluate or estimate the amount of beach erosion caused by solitary waves. Experimental assessment is necessary to comprehend the process of sediment transport on a slope. The prismatic rectangular channel is 12 m long, 0.8 m wide, and 0.75 m high. A sluice gate is applied at prismatic channel in order to produce the solitary waves. Upstream water depth is more than channel water depth and the sluice gate is suddenly opened to simulate conditions of solitary waves. A sand slope with a 1/6 and a sediment thickness is 0.03 m. The experimental sediments are used anthracite (d_50=1.547 mm ,C_u=1.38) and Jumoonjin sand (d_50=0.627 mm ,C_u=1.68). Specific laboratory equipment are designed to collect suspended sediment samples at the same time along the wave propagation at 5 points with evenly space. Each amount of sampling is approximately 25 ml and they are completely dried in oven over 24 hours according to the USGS (Guideline and standard techniques and method 3-C4). Two video cameras (Model No. : Sony, HDR-XR550) are mounted for capturing images at top and side-view when the processes of solitary wave and run up/down on slope. Also, this study are analyzed the correlation between Suspended sediment concentration and turbidity. Also, this study are analyzed the correlation between suspended sediment concentration and turbidity. Turbidity is used to verify suspended sediment concentration. Dimensionless analyses of experimental results carried out in this study. One dimensionless parameter is expressed with pressure of solitary wave on a slope to suspended sediment concentration, which is concerned about lifting force. The other is relate to drag force presenting with run up/down velocity on a slope and

  5. Suspended animation for delayed resuscitation. (United States)

    Safar, Peter J; Tisherman, Samuel A


    'Suspended animation for delayed resuscitation' is a new concept for attempting resuscitation from cardiac arrest of patients who currently (totally or temporarily) cannot be resuscitated, such as traumatic exsanguination cardiac arrest. Suspended animation means preservation of the viability of brain and organism during cardiac arrest, until restoration of stable spontaneous circulation or prolonged artificial circulation is possible. Suspended animation for exsanguination cardiac arrest of trauma victims would have to be induced within the critical first 5 min after the start of cardiac arrest no-flow, to buy time for transport and resuscitative surgery (hemostasis) performed during no-flow. Cardiac arrest is then reversed with all-out resuscitation, usually requiring cardiopulmonary bypass. Suspended animation has been explored and documented as effective in dogs in terms of long-term survival without brain damage after very prolonged cardiac arrest. In the 1990s, the Pittsburgh group achieved survival without brain damage in dogs after cardiac arrest of up to 90 min no-flow at brain (tympanic) temperature of 10 degrees C, with functionally and histologically normal brains. These studies used emergency cardiopulmonary bypass with heat exchanger or a single hypothermic saline flush into the aorta, which proved superior to pharmacologic strategies. For the large number of normovolemic sudden cardiac death victims, which currently cannot be resuscitated, more research in large animals is needed.

  6. Suspended biofilm carrier and activated sludge removal of acidic pharmaceuticals

    DEFF Research Database (Denmark)

    Falås, Per; Baillon-Dhumez, Aude; Andersen, Henrik Rasmus


    Removal of seven active pharmaceutical substances (ibuprofen, ketoprofen, naproxen, diclofenac, clofibric acid, mefenamic acid, and gemfibrozil) was assessed by batch experiments, with suspended biofilm carriers and activated sludge from several full-scale wastewater treatment plants. A distinct...... and attached solids for the carriers) of diclofenac, ketoprofen, gemfibrozil, clofibric acid and mefenamic acid compared to the sludges. Among the target pharmaceuticals, only ibuprofen and naproxen showed similar removal rates per unit biomass for the sludges and biofilm carriers. In contrast...

  7. Quantitative suspended sediment mapping using aircraft remotely sensed multispectral data. [in Virginia (United States)

    Johnson, R. W.


    Suspended sediment is an important environmental parameter for monitoring water quality, water movement, and land use. Quantitative suspended sediment determinations were made from analysis of aircraft remotely sensed multispectral digital data. A statistical analysis and derived regression equation were used to determine and plot quantitative suspended sediment concentration contours in the tidal James River, Virginia, on May 28, 1974. From the analysis, a single band, Band 8 (0.70-0.74 microns), was adequate for determining suspended sediment concentrations. A correlation coefficient of 0.89 was obtained with a mean inaccuracy of 23.5 percent for suspended sediment concentrations up to about 50 mg/l. Other water quality parameters - secchi disc depth and chlorophyll - also had high correlations with the remotely sensed data. Particle size distribution had only a fair correlation with the remotely sensed data.

  8. Spatial Distribution of Suspended Particulate Matter in Mtwapa ...

    African Journals Online (AJOL)

    Surface water concentrations of inorganic nutrients and suspended particulate matter (SPM) components from Mtwapa and Shirazi creeks in Kenya were measured and compared. This was aimed at assessing the contribution of phytoplankton carbon, particulate organic carbon (POC) and detritus on the total SPM pool, and ...

  9. Evaluation of the suspending properties of Abizia zygia gum on ...

    African Journals Online (AJOL)

    Method: The suspending properties of Albizia zygia gum (family Mimosoideae) were evaluated comparatively with those of Compound Tragacanth, Acacia and Gelatin at concentration range of 0.5 – 4.0%w/v in Sulphadimidine suspension. Characterization tests were carried out on purified Albizia zygia gum. Sedimentation ...

  10. 7 CFR 1206.21 - Suspend. (United States)


    ... part thereof during a particular period of time specified in the rule. ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE MANGO PROMOTION, RESEARCH, AND INFORMATION Mango Promotion, Research, and Information Order Definitions § 1206.21 Suspend. Suspend means to...

  11. Physical and biological changes of suspended particles in a free surface flow constructed wetland

    NARCIS (Netherlands)

    Mulling, B.T.M.; van den Boomen, R.M.; Claassen, T.H.L.; van der Geest, H.G.; Kappelhof, J.W.N.M.; Admiraal, W.


    Suspended particles are considered as contaminants in treated wastewater and can have profound effects on the biological, physical and chemical properties of receiving aquatic ecosystems, depending on the concentration, type and nature of the suspended particles. Constructed wetlands are known to

  12. Temporal and spatial changes of cadmium in the near-bottom suspended matter of the Pomeranian Bay - Arkona Deep system

    Directory of Open Access Journals (Sweden)

    Andrzej Staniszewski


    Full Text Available Owing to the high toxicity of cadmium (Cd towards biota and the considerable quantities of this element entering the environment from anthropogenic sources, interest in its biogeochemistry is increasing. This is also true for the marine environment, which serves as a sink for both natural and anthropogenic Cd loads entering the hydrosphere and the atmosphere. The distribution of Cd in the coastal zone of the marine environment is governed primarily by the flux of the so-called fluffy layer suspended matter (FLSM, which spreads across the top of the sea floor as a several-centimetre-thick layer containing highly concentrated suspended matter. Both total contents and solid speciation of Cd was measured in FLSM collected in the Pomeranian Bay - Arkona Deep system (Western Baltic Proper in the course of the three-year-long study. Seasonal changes in the total Cd content (0.5-1.8 µg g–1 dry matter were attributed to the contribution of organic suspensions originating from algal blooms. The decreasing content of Cd in FLSM offshore is due to the input of Cd-rich suspended matter from the River Odra (Oder, and the decreasing organic matter content in FLSM with increasing depth. The contribution of labile fractions (adsorbed and bound to iron III hydroxides was found to be from 50 to 75% of the total content. In view of the substantial mobility and bioavailability of the fractions, this is a highly alarming feature.

  13. Pre-concentration and determination of zinc in water samples by ligand assisted pseudo stirbar hollow fiber solid/liquid phase microextraction

    Directory of Open Access Journals (Sweden)

    Zarrin Es’haghi


    Full Text Available Pre-concentration and determination of Zn (II across a ligand assisted pseudo stirbar hollow fiber solid/liquid phase microextraction method in water samples has been investigated. All detections were carried out by differential pulse anodic stripping voltammetry (DPASV. The method involves microextraction and pre-concentration of Zn (II on the pseudo stir bar hollow fiber. Then desorption has been done using suitable solvent containing suitable ligand as complexing agent. The optimized conditions were obtained. The relationship between the peak current and concentration was linear over the range of 0.05–500 ng mL−1. The limit of detection was 0.015 ng mL−1. Under the optimized conditions, the pre-concentration factor is 5140. The applicability of the developed technique was evaluated by application to spiked, environmental water samples.

  14. Development of Efficient Sludge Collection Cones for Concentration of Raceway-Derived Solids in Recirculating Aquaculture Systems

    DEFF Research Database (Denmark)

    Rasmussen, Michael R.; Laursen, Jesper; McLean, E


    scale model. Based on this calibrated CFD model, five different principal designs of cones were evaluated. The results suggest that adjusting cone geometry can significantly enhance the efficiency of sludge collection in raceways. More efficient cone design will not only result in optimized solids...

  15. A strain of Saccharomyces cerevisiae evolved for fermentation of lignocellulosic biomass displays improved growth and fermentative ability in high solids concentrations and in the presence of inhibitory compounds

    Directory of Open Access Journals (Sweden)

    Hawkins Gary M


    Full Text Available Abstract Background Softwoods are the dominant source of lignocellulosic biomass in the northern hemisphere, and have been investigated worldwide as a renewable substrate for cellulosic ethanol production. One challenge to using softwoods, which is particularly acute with pine, is that the pretreatment process produces inhibitory compounds detrimental to the growth and metabolic activity of fermenting organisms. To overcome the challenge of bioconversion in the presence of inhibitory compounds, especially at high solids loading, a strain of Saccharomyces cerevisiae was subjected to evolutionary engineering and adaptation for fermentation of pretreated pine wood (Pinus taeda. Results An industrial strain of Saccharomyces, XR122N, was evolved using pretreated pine; the resulting daughter strain, AJP50, produced ethanol much more rapidly than its parent in fermentations of pretreated pine. Adaptation, by preculturing of the industrial yeast XR122N and the evolved strains in 7% dry weight per volume (w/v pretreated pine solids prior to inoculation into higher solids concentrations, improved fermentation performance of all strains compared with direct inoculation into high solids. Growth comparisons between XR122N and AJP50 in model hydrolysate media containing inhibitory compounds found in pretreated biomass showed that AJP50 exited lag phase faster under all conditions tested. This was due, in part, to the ability of AJP50 to rapidly convert furfural and hydroxymethylfurfural to their less toxic alcohol derivatives, and to recover from reactive oxygen species damage more quickly than XR122N. Under industrially relevant conditions of 17.5% w/v pretreated pine solids loading, additional evolutionary engineering was required to decrease the pronounced lag phase. Using a combination of adaptation by inoculation first into a solids loading of 7% w/v for 24 hours, followed by a 10% v/v inoculum (approximately equivalent to 1 g/L dry cell weight into 17

  16. International Odra project (IOP) 'Interdisciplinary German Polish studies on the behaviour of pollutants in the Oder system'. Sub project 4: the state of suspended particulate matter in the Odra River system. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Henning, K.H.; Damke, H.; Kasbohm, J.; Puff, T.; Breitenbach, E.; Theel, O.; Kiessling, A.


    The purpose of the present project was to characterise the pollutant freight of suspended matter and suspended-matter-borne sediments in the Oder river system on the basis of large samples drawn at selected sampling sites. One of the major goals was to assess and draw up a balance of the transport regime of suspended matter between the compartments water, suspended matter and sediments. Special attention was given to the composition and structure of suspended matter as well as to the distribution of trace elements in the various components. Furthermore, the study was intended to provide ecology-related information on the basis of selected biogenic components. Statements on the time course of pollution of estuarine waters and the Baltic Sea by way of the Oder can be derived from a characterisation of current fluviatile solids (suspended matter and suspended-matter-borne sediments) and determination of their quantitative proportions. The following research strategy was derived from these goals: for a characterisation of suspended matter in terms of composition, structure and biogenic origin it is necessary to determine the concentration of suspended matter, its granulometric composition, carbon and sulphur content, biogenic opal content, mineral content, phase composition, metal content, structure of suspended flakes and association of diatoms in the suspended flakes and on the periphyton. [German] Das Vorhaben ist darauf ausgerichtet, den Belastungszustand der Schwebstoffe und schwebstoffbuertigen Sedimente im Oderflusssystem anhand von Grossproben ausgewaehlter Probenahmeorte zu charakterisieren. Ein wesentliches Ziel ist die Beurteilung des Transportregimes der Schwebstoffe zwischen den Kompartimenten Wasser, Schwebstoff und Sediment sowie seine Bilanzierung. Dabei gilt die besondere Aufmerksamkeit der Zusammensetzung und der Struktur der Schwebstoffe sowie die Spurenelementspeziation an die unterschiedlichen Bestandteile. Weiterhin werden oekologische Aussagen

  17. Stability of flocculated particles in concentrated and high hydrophilic solid layer-by-layer (LBL) emulsions formed using whey proteins and gum Arabic. (United States)

    Lim, Aaron S L; Roos, Yrjö H


    The objective of the present study was to investigate flocculation in layer-by-layer (LBL) emulsion systems with high total solids content and deflocculation at various pH conditions, and the effects of whey protein isolate (WPI) concentration and total solids content on the stability of LBL emulsions. WPI (1.96% (1WPI) or 10.71% (10WPI), w/w in water) was prepared in water and high-pressure homogenized with sunflower oil (10%, w/w, of total emulsion). Gum Arabic (0.15%, w/w, in total emulsion) was added to assemble electrostatically on WPI at oil particle interfaces at pH3.5 using aqueous citric acid (10% w/w) forming LBL emulsion. The ζ-potential measurements showed charge reversal upon addition of gum Arabic solution into single layer (SL) emulsion confirming the formation of LBL interface. Trehalose:maltodextrin mixture (1:1, w/w, total emulsion, 28.57% (28) or 57.14% (57), w/w, in water) was used in the continuous phase. The high total solids content of the system results in depletion flocculation of the particles leading to bridging flocculation without coalescence as deflocculation into individual particles occurred with increasing pH from pH3.5 to pH6.5 in 10WPI systems. Deflocculation was evident in 10WPI-28 and 10WPI-57 as found from a decreased ζ-average diameter and visually under microscope. Coalescence was observed in 1WPI systems. Viscosity of the systems was significantly (P<0.05) increased with higher total solids content. Accelerated destabilization test showed that systems at higher WPI and total solids contents exhibited the highest stability against creaming. Deflocculation in LBL systems can be controlled by pH while high solids in the aqueous phase provide stability against creaming. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Hydrodynamic and suspended sediment transport controls on river mouth morphology (United States)

    Falcini, F.; Piliouras, A.; Garra, R.; Guerin, A.; Jerolmack, D. J.; Rowland, J.; Paola, C.


    mouths building into standing bodies of water have strikingly varied growth habits. This presents a compelling pattern formation problem that is also of great practical relevance for subsurface prediction and managing coastal wetlands. Here we present a generalized 2.5-dimensional potential vorticity (PV) theory that explains sedimentation patterns of a sediment-laden stationary jet by coupling an understanding of vorticity with suspended sediment concentration fields. We explore the physical meaning of this new sediment-PV definition, and its impact on outflow depositional patterns, by analyzing data from a shallow wall-bounded plane jet experiment and by discussing new theoretical insights. A key result is that lateral advection and diffusion of suspended sediment are directly proportional to jet vorticity, a feature that reveals the mechanistic process that forms elongated channels by focused levee deposition. The new PV theory constitutes a more generalized mathematical framework that expands the Rouse theory for the equilibrium of suspended sediment.

  19. Self-Suspended Suspensions of Covalently Grafted Hairy Nanoparticles

    KAUST Repository

    Choudhury, Snehashis


    © 2015 American Chemical Society. Dispersions of small particles in liquids have been studied continuously for almost two centuries for their ability to simultaneously advance understanding of physical properties of fluids and their widespread use in applications. In both settings, the suspending (liquid) and suspended (solid) phases are normally distinct and uncoupled on long length and time scales. In this study, we report on the synthesis and physical properties of a novel family of covalently grafted nanoparticles that exist as self-suspended suspensions with high particle loadings. In such suspensions, we find that the grafted polymer chains exhibit unusual multiscale structural transitions and enhanced conformational stability on subnanometer and nanometer length scales. On mesoscopic length scales, the suspensions display exceptional homogeneity and colloidal stability. We attribute this feature to steric repulsions between grafted chains and the space-filling constraint on the tethered chains in the single-component self-suspended materials, which inhibits phase segregation. On macroscopic length scales, the suspensions exist as neat fluids that exhibit soft glassy rheology and, counterintuitively, enhanced elasticity with increasing temperature. This feature is discussed in terms of increased interpenetration of the grafted chains and jamming of the nanoparticles. (Chemical Presented).

  20. Technological advances in suspended-sediment surrogate monitoring (United States)

    Gray, John R.; Gartner, Jeffrey W.


    Surrogate technologies to continuously monitor suspended sediment show promise toward supplanting traditional data collection methods requiring routine collection and analysis of water samples. Commercially available instruments operating on bulk optic (turbidity), laser optic, pressure difference, and acoustic backscatter principles are evaluated based on cost, reliability, robustness, accuracy, sample volume, susceptibility to biological fouling, and suitable range of mass concentration and particle size distribution. In situ turbidimeters are widely used. They provide reliable data where the point measurements can be reliably correlated to the river's mean cross section concentration value, effects of biological fouling can be minimized, and concentrations remain below the sensor's upper measurement limit. In situ laser diffraction instruments have similar limitations and can cost 6 times the approximate $5000 purchase price of a turbidimeter. However, laser diffraction instruments provide volumetric-concentration data in 32 size classes. Pressure differential instruments measure mass density in a water column, thus integrating substantially more streamflow than a point measurement. They are designed for monitoring medium-to-large concentrations, are generally unaffected by biological fouling, and cost about the same as a turbidimeter. However, their performance has been marginal in field applications. Acoustic Doppler profilers use acoustic backscatter to measure suspended sediment concentrations in orders of magnitude more streamflow than do instruments that rely on point measurements. The technology is relatively robust and generally immune to effects of biological fouling. Cost of a single-frequency device is about double that of a turbidimeter. Multifrequency arrays also provide the potential to resolve concentrations by clay silt versus sand size fractions. Multifrequency hydroacoustics shows the most promise for revolutionizing collection of continuous

  1. Yield effects on 2-methoxy-3-isobutylpyrazine concentration in cabernet sauvignon using a solid phase microextraction gas chromatography/mass spectrometry method. (United States)

    Chapman, Dawn M; Thorngate, John H; Matthews, Mark A; Guinard, Jean-Xavier; Ebeler, Susan E


    A rapid and automated solid phase microextraction (SPME) stable isotope dilution gas chromatography/mass spectrometry (GC-MS) method for 2-methoxy-3-isobutylpyrazine (MIBP) quantification in red wine was developed. Wines with 30% (w/v) NaCl and 2-methoxy-(2)H(3)-3-isobutylpyrazine internal standard were sampled with a 2 cm divinylbenzene/carboxen/poly(dimethylsiloxane) SPME fiber for 30 min at 40 degrees C and analyzed by GC-MS. The method was used to measure MIBP concentrations in Cabernet Sauvignon wines that were produced from six winter pruning treatments over two vintages. MIBP concentrations were significantly negatively correlated with buds per vine. In addition, the MIBP concentration was directly related to sensory vegetal intensity ratings obtained by descriptive analysis.

  2. Validation and application of the methodology for analysis of radon concentration in the air through the technique of solid state nuclear track detectors (SSNTD)

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Caroline de [Pontificia Universidade Catolica de Minas Gerais (PUC-Pocos), Pocos de Caldas, MG (Brazil); Comissao Nacional de Energia Nuclear (LAPOC/CNEN), Pocos de Caldas, MG (Brazil). Lab. de Pocos de Caldas; Silva, Nivaldo Carlos da, E-mail: [Comissao Nacional de Energia Nuclear (LAPOC/CNEN), Pocos de Caldas, MG (Brazil). Lab. de Pocos de Caldas


    Radon is a radioactive noble gas that occurs naturally in soil and could enter into residential. The decay products of radon are radioactive metals which, when inhaled, can be retained in the respiratory system, leading to an internal dose of radiation. The monitoring of radon levels in residences and workplaces is extremely important, since high concentrations of this gas can cause serious public health problems. This study analyzed the concentration of radon in the air in 94 work environments at the Laboratory of Pocos de Caldas - LAPOC/CNEN, including laboratories, administrative rooms, workshop, warehouse and guardhouse. The method employed in the monitoring was the technique of solid state nuclear track detectors, known as SSNTD. For calibration and validation of this method, controlled experiments were conducted in laboratory with specific instrumentation. The monitoring results indicated that most environments present radon concentrations above 100 Bq m{sup -3}, which is the reference level recommended by the World Health Organization. (author)

  3. Suspended sediment yield in Texas watersheds (United States)

    Coonrod, Julia Ellen Allred

    The Texas Water Development Board collected suspended sediment samples across the state of Texas for approximately 60 years. Until this research, no comprehensive analysis of the data had been conducted. This study compiles the suspended sediment data along with corresponding streamflow and rainfall. GIS programs are developed which characterize watersheds corresponding to the sediment gauging stations. The watersheds are characterized according to topography, climate, soils, and land use. All of the data is combined to form several SAS data sets which can subsequently be analyzed using regression. Annual data for all of the stations across the state are classified temporally and spatially to determine trends in the sediment yield. In general, the suspended sediment load increases with increasing runoff but no correlation exists with rainfall. However, the annual average rainfall can be used to classify the watersheds according to climate, which improves the correlation between sediment load and runoff. The watersheds with no dams have higher sediment loads than watersheds with dams. Dams in the drier parts of Texas reduce the sediment load more than dams in the wetter part of the state. Sediment rating curves are developed separately for each basin in Texas. All but one of the curves fall into a band which varies by about two orders of magnitude. The study analyzes daily time series data for the Lavaca River near Edna station. USGS data are used to improve the sediment rating curve by the addition of physically related variables and interaction terms. The model can explain an additional 41% of the variability in sediment concentration compared to a simple bivariate regression of sediment load and flow. The TWDB daily data for the Lavaca River near Edna station are used to quantify temporal trends. There is a high correlation between sediment load and flowrate for the Lavaca River. The correlation can be improved by considering a flow-squared term and by

  4. [Impacts of Sediment Disturbance on the Distribution of Suspended Particle Size and Phosphorus]. (United States)

    Guo, Jun-rui; Li, Da-peng; Liu, Yan-jian


    To clarify the influence of the sediments disturbance on the particle size distribution of suspended solids, and the influence of particle distribution on the forms of dissolved phosphorous in the overlaying water, the sediments and overlying water from Meiliang Bay, Taihu Lake, were used to conduct the indoor simulation experiments to investigate the particle size of suspended solids according to the Ubbelobde particle size criteria and the distribution of phosphorus compounds in the overlying water under the disturbance circumstances. The results indicated that the average proportions of small (0-10 microm), middle (10-20 microm) and large (> or = 20 microm) diameter particles presented different trends of increasing, decreasing and staying stable, respectively. It indicated the possible transformation of particle size of suspended solids from small-middle diameter to large diameter. In addition, the data of DTP/TP and DIP/TP showed a periodical variation with the corresponding periodical variety of particle diameter in suspended solids, while ns obvious variety of DTP and DIP was observed. It suggested that disturbance enhanced the ability of phosphorus immobilization by suspended solids. On the other band, the percentages of DTP in TP and DIP in TP were 19% and 13% under the disturbance, respectively, and they were obviously lower than those (DTP/TP, 80% and DIP/TP, 69% ) in the control. It indicated that tbs transformation of particle size of suspended solids from small-middle diameter to large diameter due to disturbance was in favor of tbe adsorption and sedimentation of dissolved phosphorus. Accordingly, the formation of particle phosphorus was enhanced. Therefore, it delayed the development of eutrophication in the water body.

  5. Sulfate and organic matter concentration in relation to hydrogen sulfide generation at inert solid waste landfill site - Limit value for gypsum. (United States)

    Asakura, Hiroshi


    In order to suggest a limit value for gypsum (CaSO4) for the suppression of hydrogen sulfide (H2S) generation at an inert solid waste landfill site, the relationship between raw material (SO4 and organic matter) for H2S generation and generated H2S concentration, and the balance of raw material (SO4) and product (H2S) considering generation and outflow were investigated. SO4 concentration should be less than approximately 100mg-SO4/L in order to suppress H2S generation to below 2000ppm. Total organic carbon (TOC) concentration should be less than approximately 200mg-C/L assuming a high SO4 concentration. The limit value for SO4 in the ground is 60mg-SO4/kg with 0.011wt% as gypsum dihydrate, i.e., approximately 1/10 of the limit value in inert waste as defined by the EU Council Decision (560mg-SO4/kg-waste). The limit value for SO4 in inert waste as defined by the EU Council Decision is high and TOC is strictly excluded. The cumulative amount of SO4 outflow through the liquid phase is much larger than that through the gas phase. SO4 concentration in pore water decreases with time, reaching half the initial concentration around day 100. SO4 reduction by rainfall can be expected in the long term. Copyright © 2015 Elsevier Ltd. All rights reserved.

  6. Extraction and RT-qPCR detection of enteroviruses from solid environmental matrixes: Method decision tree for different sample types and viral concentrations. (United States)

    Martín-Díaz, Julia; Lucena, Francisco


    Quantitative RT-PCR methods (RT-qPCR) are becoming increasingly desirable for the detection of enteric viruses in solid environmental matrixes such as sediments, soils and sewage sludge. However, effective methodologies that allow the extraction of high quality RNA ready for molecular quantification continue to be evaluated. In the present study, four different methods for enterovirus extraction from solid environmental matrixes were compared in terms of viral recovery and inhibitor removal. Three indirect methods based on glycine elution and concentration by ultracentrifugation were tested. The main differences between indirect methods were the sample to glycine buffer ratio, and the ultracentrifugation protocol applied. One commercial direct method was also tested. The indirect methods produced better results than the direct method. The ultracentrifugation led to viral losses in samples with high titers; however, as the virus concentration reduced, the ultracentrifugation became increasingly important for viral recovery. Two commercial RNA extraction kits were also evaluated and it was selected the most effective in removing RT-qPCR inhibitors. The results obtained allowed the development of a method decision tree with three versions that are suitable for different samples and viral concentrations. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Application of PAC and flocculants for improving settling of solid particles in oilfield wastewater with high salinity and Ca2. (United States)

    Liu, Guoliang; Zhang, Fusheng; Qu, Yuanzhi; Liu, He; Zhao, Lun; Cui, Mingyue; Ou, Yangjian; Geng, Dongshi


    The suspended solids in wastewater from Rekabak oilfield, Kazakhstan, were characterized and treated with flocculants to enhance settling. The wastewater contained a high concentration of total dissolved solids and calcium ion. Scanning electron microscopy and energy dispersive X-ray analyses showed that suspended solids were mainly composed of corrosion products (iron oxides) and silicon dioxide particles. Also, much salt deposition from wastewater caused a large increase in the suspended solids value. The settling of solid particles in wastewater was investigated by turbidity decrease within 60 min. The particle settling was enhanced by adding polyaluminum chloride (PAC) as coagulant and hydrolyzed polyacryamide (HPAM) or cationic polyacrylamide (CPAM) as flocculant. At optimal dose, the particle settling ability with PAC and CPAM was better than that with PAC and HPAM. Particle size analysis showed that HPAM or CPAM with high molecular weight played an important role for enlarging the particle size. The experiments with simulated wastewater showed that particle settling by using HPAM deteriorated significantly compared to that by CPAM at high calcium ion. This study provides further understanding about the effect of high salinity and Ca2+ on solids formation, flocculant performance and particle settling. Meanwhile, the results are also helpful to develop novel flocculants used for high salinity wastewater.

  8. Inhibitory effect of high calcium concentration on municipal solid waste leachate treatment by the activated sludge process. (United States)

    Xia, Yi; He, Pin Jing; Pu, Hong Xia; Lü, Fan; Shao, Li Ming; Zhang, Hua


    This research focused on the inhibitory effects of Ca on the aerobic biological treatment of landfill leachate containing extremely high Ca concentrations. When the Ca concentration in leachate to be treated was more than 4500 mg l-1, the total organic carbon removal rate was significantly reduced and the processing time to achieve the same removal efficiency was 1.4 times that in the control treatment without added Ca. In contrast, the total nitrogen and ammonia nitrogen (NH4+-N) removal efficiencies were positively related to the Ca concentration, increasing from 65.2% to 81.2% and from 69.2% to 83.7%, respectively, when the dosage of added Ca increased from zero to 8000 mg l-1. During aerobic treatment, the reductions of solution Ca concentration were in the range of 1003-2274 mg l-1 and were matched with increases in the Ca content in the residual sludge. The inhibition threshold of Ca in the leachate treated by the activated sludge process appeared to be 4500 mg l-1, which could be realized by controlling the influent Ca concentration and using an appropriate sludge return ratio in the activated sludge process.

  9. Rippling instabilities in suspended nanoribbons (United States)

    Wang, Hailong; Upmanyu, Moneesh


    Morphology mediates the interplay between the structure and electronic transport in atomically thin nanoribbons such as graphene as the relaxation of edge stresses occurs preferentially via out-of-plane deflections. In the case of end-supported suspended nanoribbons that we study here, past experiments and computations have identified a range of equilibrium morphologies, in particular, for graphene flakes, yet a unified understanding of their relative stability remains elusive. Here, we employ atomic-scale simulations and a composite framework based on isotropic elastic plate theory to chart out the morphological stability space of suspended nanoribbons with respect to intrinsic (ribbon elasticity) and engineered (ribbon geometry) parameters, and the combination of edge and body actuation. The computations highlight a rich morphological shape space that can be naturally classified into two competing shapes, bendinglike and twistlike, depending on the distribution of ripples across the interacting edges. The linearized elastic framework yields exact solutions for these rippled shapes. For compressive edge stresses, the body strain emerges as a key variable that controls their relative stability and in extreme cases stabilizes coexisting transverse ripples. Tensile edge stresses lead to dimples within the ribbon core that decay into the edges, a feature of obvious significance for stretchable nanoelectronics. The interplay between geometry and mechanics that we report should serve as a key input for quantifying the transport along these ribbons.

  10. The influence of blood sample storage time on the propofol concentration in plasma and solid blood elements. (United States)

    Dawidowicz, A L; Fijalkowska, A; Nestorowicz, A; Fornal, E


    In order to describe the changes of propofol concentration in whole blood and in its components during the blood storage we examined venous blood samples collected from patients anaesthetized either with or without propofol. Blood samples from patients anaesthetized without propofol were spike with propofol 45 min before analysis. Propofol concentration was examined in whole blood, plasma, rinsed formed elements and rinsed and lysed formed blood elements by means of HPLC after 1, 4, 7, 13, 21, 25 and 28 days of storage. There was significant decrease in plasma concentration of propofol during the first few days of sample storage followed by its increase during subsequent days. The opposite phenomenon was observed for formed blood elements. The findings support the hypothesis that propofol distribution between blood components changes in time. Copyright 2001 John Wiley & Sons, Ltd.

  11. Biohydrogen production from household solid waste (HSW) at extreme-thermophilic temperature (70 degrees C) - Influence of pH and acetate concentration

    DEFF Research Database (Denmark)

    Liu, Dawei; Min, Booki; Angelidaki, Irini


    Hydrogen production from household solid waste (HSW) was performed via dark fermentation by using an extreme-thermophilic mixed culture, and the effect of pH and acetate on the biohydrogen production was investigated. The highest hydrogen production yield was 257 +/- 25 mL/gVS(added) at the optimum...... pH of 7.0. Acetate was proved to be inhibiting the dark fermentation process at neutral pH, which indicates that the inhibition was caused by total acetate concentration not by undissociated acetate. Initial inhibition was detected at acetate concentration of 50 mM, while the hydrogen fermentation...... was seriously inhibited at acetate concentration of 200 mM. At 200 mM acetate concentration, the hydrogen yield was 36 +/- 25 mL/gVS(added), which was almost 7 times lower than the yield of 254 +/- 13 mL/gVS(added), which was achieved at lower acetate concentration (5-25 mM). Additional to the negative effect...

  12. Influence of substrate concentration and moisture content on the specific methanogenic activity of dry mesophilic municipal solid waste digestate spiked with propionate. (United States)

    Le Hyaric, Ronan; Chardin, Caroline; Benbelkacem, Hassen; Bollon, Julien; Bayard, Rémy; Escudié, Renaud; Buffière, Pierre


    The objective of this study was to evaluate the influence of substrate concentration and moisture content on the specific methanogenic activity (SMA) of a fresh dry mesophilic digestate from a municipal solid waste digester plant. For this purpose, SMA tests were performed under mesophilic conditions into glass bottles of 500 mL volume used as batch reactors, during a period of 20-25 days. Propionate was used as substrate at concentrations ranging from 1 to 10 gCOD/kg. Four moisture contents were studied: 65%, 75%, 80% and 82%. Experimental results showed that propionate concentration and moisture content strongly influenced the SMA. The highest SMA was observed at a substrate concentration of 10 gCOD/kg (11.3 mgCOD gVS(-1) d(-1) for the second dose of propionate) and at a moisture content of 82% (7.8 mgCOD gVS(-1) d(-1) for the second dose of propionate, at a concentration of 5 gCOD/kg). SMA was found to decrease linearly when decreasing the moisture content. Copyright © 2010 Elsevier Ltd. All rights reserved.

  13. Efficient conversion of high concentration of glycerol to Monacolin K by solid-state fermentation of Monascus purpureus using bagasse as carrier. (United States)

    Lu, Li-Ping; Zhang, Bo-Bo; Xu, Gan-Rong


    High concentration of glycerol was used as the sole carbon source for efficient production of Monacolin K (MK) by solid-state fermentation (SSF) of Monascus purpureus 9901 using agricultural residue (bagasse), as an inert carrier. A comparative study showed that MK production in SSF was about 5.5 times higher than that of submerged fermentation when 26 % of glycerol was used, which may be due to the formation of glycerol concentration gradients in the inert carrier and less catabolite repression in SSF. For enhancement of MK yield in SSF, the effects of different influential variables, such as glycerol concentration, nitrogen source and its concentration, initial moisture content, inoculum size and particle size of bagasse, were systematically examined. All the factors mentioned above had an effect on the MK production in SSF to some extent. The maximal yield of MK (12.9 mg/g) was achieved with 26 % glycerol, 5 % soybean meal, 51 % initial moisture content, 20 % inoculum size and 1 mm particle size of bagasse. The results in this study may expand our understanding on the application of SSF using agricultural residue as carrier for production of useful microbial metabolites, especially the efficient conversion of high concentration of glycerol to MK by Monascus purpureus.

  14. Effects of solids concentration, pH and carbon addition on the production rate and composition of volatile fatty acids in prefermenters using primary sewage sludge. (United States)

    Zeng, R J; Yuan, Z; Keller, J


    Increasing evidence is emerging that the performance of enhanced biological phosphorus removal (EBPR) systems relies on not only the total amount but also the composition of volatile fatty acids (VFAs). Domestic wastewater often contains limited amounts of VFAs with acetic acid typically being the dominating species. Consequently, prefermenters are often employed to generate additional VFAs to meet the demand for carbon by EBPR and/or denitrification processes. Limited knowledge is currently available on the effects of operational conditions on the production rate and composition of VFAs in prefermenters. In this study, a series of controlled batch experiments were conducted with sludge from a full-scale prefermenter to determine the impact of solids concentration, pH and addition of molasses on prefermentation processes. It was found that an increase in solids concentration enhanced total VFA production with an increased propionic acid fraction. The optimal pH for prefermentation was in the range of 6-7 with significant productivity loss when pH was below 5.5. Molasses addition significantly increased the production of VFAs particularly the propionic acid. However, the fermentation rate was likely limited by the biological activity of the sludge rather than by the amount of molasses added.

  15. Mucous Secretion and Cilia Beating Defend Developing Coral Larvae from Suspended Sediments.

    Directory of Open Access Journals (Sweden)

    Gerard F Ricardo

    Full Text Available Suspended sediments produced from dredging activities, or added to the sediment budget via river runoff, are a concern for marine resource managers. Understanding the impact of suspended sediments on critical life history stages of keystone species like corals is fundamental to effective management of coastlines and reefs. Coral embryos (Acropora tenuis and A. millepora and larvae (A. tenuis, A. millepora and Pocillopora acuta were subjected to a range of suspended sediment concentrations of different sediment types (siliciclastic and carbonate to assess concentration-response relationships on ecologically relevant endpoints, including survivorship and ability to metamorphose. Embryos were subjected to short (12 h suspended sediment exposures from ages of 3-12 hours old or a long (30 h exposure at 6 hours old. Neither the survivorship nor metamorphosis function of embryos were significantly affected by realistic sediment exposures to ~1000 mg L-1. However, some embryos exhibited a previously undescribed response to dynamically suspended sediments, which saw 10% of the embryos form negatively buoyant cocoons at siliciclastic suspended sediment concentrations ≥35 mg L-1. Scanning electron and optical microscopy confirmed the presence of a coating on these embryos, possibly mucus with incorporated sediment particles. Cocoon formation was common in embryos but not in larvae, and occurred more often after exposure to siliciclastic rather than carbonate sediments. Once transferred into sediment-free seawater, functional ~36-h-old embryos began emerging from the cocoons, coinciding with cilia development. Ciliated (> 36-h-old larvae exposed to suspended sediments for 60 h were also observed to secrete mucus and were similarly unaffected by suspended sediment concentrations to ~800 mg L-1. This study provides evidence that mucous secretion and cilia beating effectively protect coral embryos and larvae from suspended sediment and that these mechanisms

  16. The Influence of Suspended Inert Solid Particles on Zinc Corrosion

    DEFF Research Database (Denmark)

    Bech-Nielsen, Gregers


    The rate of corrosion of electroplated zinc in near-neutral chloride solutions can be lowered by as much as 75% by adding fine, inert particles of substances such as MnO2, Fe3O4, SiC and TiN to the well-stirred solution. Spreading of local areas of etching is also stopped. Copyright (C) 1996...

  17. Determination of lead and cadmium concentration limits in agricultural soil and municipal solid waste compost through an approach of zero tolerance to food contamination. (United States)

    Saha, Jayanta Kumar; Panwar, N R; Singh, M V


    Cadmium and lead are important environmental pollutants with high toxicity to animals and human. Soils, though have considerable metal immobilizing capability, can contaminate food chain via plants grown upon them when their built-up occurs to a large extent. Present experiment was carried out with the objective of quantifying the limits of Pb and Cd loading in soil for the purpose of preventing food chain contamination beyond background concentration levels. Two separate sets of pot experiment were carried out for these two heavy metals with graded levels of application doses of Pb at 0.4-150 mg/kg and Cd at 0.02-20 mg/kg to an acidic light textured alluvial soil. Spinach crop was grown for 50 days on these treated soils after a stabilization period of 2 months. Upper limit of background concentration levels (C(ul)) of these metals were calculated through statistical approach from the heavy metals concentration values in leaves of spinach crop grown in farmers' fields. Lead and Cd concentration limits in soil were calculated by dividing C(ul) with uptake response slope obtained from the pot experiment. Cumulative loading limits (concentration limits in soil minus contents in uncontaminated soil) for the experimental soil were estimated to be 170 kg Pb/ha and 0.8 kg Cd/ha. Based on certain assumptions on application rate and computed cumulative loading limit values, maximum permissible Pb and Cd concentration values in municipal solid waste (MSW) compost were proposed as 170 mg Pb/kg and 0.8 mg Cd/kg, respectively. In view of these limiting values, about 56% and 47% of the MSW compost samples from different cities are found to contain Pb and Cd in the safe range.

  18. Direct observation of solid-phase adsorbate concentration profile in powdered activated carbon particle to elucidate mechanism of high adsorption capacity on super-powdered activated carbon. (United States)

    Ando, Naoya; Matsui, Yoshihiko; Matsushita, Taku; Ohno, Koichi


    Decreasing the particle size of powdered activated carbon (PAC) by pulverization increases its adsorption capacities for natural organic matter (NOM) and polystyrene sulfonate (PSS, which is used as a model adsorbate). A shell adsorption mechanism in which NOM and PSS molecules do not completely penetrate the adsorbent particle and instead preferentially adsorb near the outer surface of the particle has been proposed as an explanation for this adsorption capacity increase. In this report, we present direct evidence to support the shell adsorption mechanism. PAC particles containing adsorbed PSS were sectioned with a focused ion beam, and the solid-phase PSS concentration profiles of the particle cross-sections were directly observed by means of field emission-scanning electron microscopy/energy-dispersive X-ray spectrometry (FE-SEM/EDXS). X-ray emission from sulfur, an index of PSS concentration, was higher in the shell region than in the inner region of the particles. The X-ray emission profile observed by EDXS did not agree completely with the solid-phase PSS concentration profile predicted by shell adsorption model analysis of the PSS isotherm data, but the observed and predicted profiles were not inconsistent when the analytical errors were considered. These EDXS results provide the first direct evidence that PSS is adsorbed mainly in the vicinity of the external surface of the PAC particles, and thus the results support the proposition that the increase in NOM and PSS adsorption capacity with decreasing particle size is due to the increase in external surface area on which the molecules can be adsorbed. Copyright © 2010 Elsevier Ltd. All rights reserved.

  19. Smart thorium and uranium determination exploiting renewable solid-phase extraction applied to environmental samples in a wide concentration range

    Energy Technology Data Exchange (ETDEWEB)

    Avivar, Jessica; Ferrer, Laura; Cerda, Victor [University of the Balearic Islands, Chemistry Department, Palma (Spain); Casas, Montserrat [University of the Balearic Islands, Physic Department, IFISC-CSIC, Palma (Spain)


    A smart fully automated system is proposed for determination of thorium and uranium in a wide concentration range, reaching environmental levels. The hyphenation of lab-on-valve (LOV) and multisyringe flow injection analysis (MSFIA), coupled to a long path length liquid waveguide capillary cell, allows the spectrophotometric determination of thorium and uranium in different types of environmental sample matrices achieving high selectivity and sensitivity levels. Online separation and preconcentration of thorium and uranium is carried out by means of Uranium and TEtraValents Actinides resin. The potential of the LOV-MSFIA makes possible the full automation of the system by the in-line regeneration of the column and its combination with a smart methodology is a step forward in automation. After elution, thorium(IV) and uranium(VI) are spectrophotometrically detected after reaction with arsenazo-III. We propose a rapid, inexpensive, and fully automated method to determine thorium(IV) and uranium(VI) in a wide concentration range (0-1,200 and 0-2,000 {mu}g L{sup -1} Th and U, respectively). Limits of detection reached are 5.9 {eta}g L{sup -1} of uranium and 60 {eta}g L{sup -1} of thorium. Different water sample matrices (seawater, well water, freshwater, tap water, and mineral water), and a channel sediment reference material which contained thorium and uranium were satisfactorily analyzed with the proposed method. (orig.)

  20. Abrasion properties of self-suspended hairy titanium dioxide nanomaterials (United States)

    Zhang, Jiao-xia; Liu, Si; Yan, Chao; Wang, Xiao-jing; Wang, Lei; Yu, Ya-ming; Li, Shi-yun


    Considering the excellent solubility of pyrrolidone ring organic compounds, the synthesized N-(trimethoxysilyl) propyl-N-methyl-2-pyrrolidone chlorides was tethered onto titanium dioxide (TiO2) nanoparticles to improve dispersion of TiO2, and then polyethylene oxide (PEO) oligomer through ion exchange embraced the tethered TiO2 to obtain a novel self-suspended hairy TiO2 nanomaterials without any solvent. A variety of techniques were carried out to illustrate the structure and properties of the self-suspended hairy TiO2 nanomaterials. It was found that TiO2 nanoparticles embody monodispersity in the hybrid system though the "false reunion" phenomenon occurring due to nonpermanent weak physical cross-linking. Remarkably, self-suspended hairy TiO2 nanomaterials exhibit lower viscosity, facilitating maneuverable and outstanding antifriction and wear resistance properties, due to the synergistic lubricating effect between spontaneously forming lubricating film and nano-lubrication of TiO2 cores, overcoming the deficiency of both solid and liquid lubricants. This make them promising candidates for the micro-electromechanic/nano-electromechanic systems (MEMS/NEMS).

  1. Temperature signal in suspended sediment export from an Alpine catchment

    Directory of Open Access Journals (Sweden)

    A. Costa


    Full Text Available Suspended sediment export from large Alpine catchments ( >  1000 km2 over decadal timescales is sensitive to a number of factors, including long-term variations in climate, the activation–deactivation of different sediment sources (proglacial areas, hillslopes, etc., transport through the fluvial system, and potential anthropogenic impacts on the sediment flux (e.g. through impoundments and flow regulation. Here, we report on a marked increase in suspended sediment concentrations observed near the outlet of the upper Rhône River Basin in the mid-1980s. This increase coincides with a statistically significant step-like increase in basin-wide mean air temperature. We explore the possible explanations of the suspended sediment rise in terms of changes in water discharge (transport capacity, and the activation of different potential sources of fine sediment (sediment supply in the catchment by hydroclimatic forcing. Time series of precipitation and temperature-driven snowmelt, snow cover, and ice melt simulated with a spatially distributed degree-day model, together with erosive rainfall on snow-free surfaces, are tested to explore possible reasons for the rise in suspended sediment concentration. We show that the abrupt change in air temperature reduced snow cover and the contribution of snowmelt, and enhanced ice melt. The results of statistical tests show that the onset of increased ice melt was likely to play a dominant role in the suspended sediment concentration rise in the mid-1980s. Temperature-driven enhanced melting of glaciers, which cover about 10 % of the catchment surface, can increase suspended sediment yields through an increased contribution of sediment-rich glacial meltwater, increased sediment availability due to glacier recession, and increased runoff from sediment-rich proglacial areas. The reduced extent and duration of snow cover in the catchment are also potential contributors to the rise in suspended sediment

  2. 23 Elemental Composition of Suspended Particulate Matter ...

    African Journals Online (AJOL)


    Elemental Composition of Suspended Particulate Matter Collected at Two Different. Heights above the Ground in A Sub-Urban Site in Kenya. Gitari W. M1, Kinyua A. M. 2, Kamau G. N3 and C. K. Gatebe C. K4. Abstract. Suspended particulate matter samples were collected in a sub-urban area in Nairobi over a 12 month ...

  3. Influence of near-bottom re-suspended sediment on benthic light availability

    DEFF Research Database (Denmark)

    Pedersen, Troels Møller; Gallegos, Charles L.; Nielsen, Søren Laurentius


    Increased light attenuation in the water column is a common consequence of the increased organic loading that accompanies anthropogenic eutrophication in coastal systems. Frequently, the best water quality correlate of the light attenuation coefficient is the total suspended solids, even in syste...

  4. Species sensitivity distributions for suspended clays, sediment burial and grain size change in the marine environment

    NARCIS (Netherlands)

    Smit, M.G.D.; Holthaus, K.I.E.; Trannum, H.C.; Neff, J.M.; Kjeilen-Eilertsen, G.; Jak, R.G.; Singsaas, I.; Huijbregts, M.A.J.; Hendriks, A.J.


    Assessment of the environmental risk of discharges, containing both chemicals and suspended solids (e.g., drilling discharges to the marine environment), requires an evaluation of the effects of both toxic and nontoxic pollutants. To date, a structured evaluation scheme that can be used for

  5. Determination of salicylic acid using a magnetic iron oxide nanoparticle-based solid-phase extraction procedure followed by an online concentration technique through micellar electrokinetic capillary chromatography. (United States)

    Chang, Yu-Hsuan; Huang, Chang-Wei; Fu, Shih-Feng; Wu, Mei-Yao; Wu, Tsunghsueh; Lin, Yang-Wei


    In this study, a magnetic iron oxide nanoparticle-based solid-phase extraction procedure combined with the online concentration and separation of salicylic acid (SA) through micellar electrokinetic chromatography-UV detection (MEKC-UV) was developed. Under optimal experimental conditions, a good linearity in the range of 0.01-100μmolL-1 was obtained with a coefficient of correlation of 0.9999. The detection sensitivity of the proposed method exhibited an approximately 1026-fold improvement compared with a single MEKC method without online concentration, and the detection limit (S/N=3) was 3.80nmolL-1. The repeatability of the method was evaluated using intraday and interday RSDs (11.5% and 17.0%, respectively). The method was used to determine SA concentrations in tobacco leaves (Nicotiana tabacum L. cv. Samsun) from the NN genotype, nn genotype, and Nt-NahG mutant strains, as well as in shampoo and ointment samples. Rapid extraction and separation (<50min), acceptable repeatability (RSD<17.0%), and high spiked recoveries (95.8%-102.4%) were observed for plants, detergents, and pharmaceuticals. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Spatio-temporal measurement of indoor particulate matter concentrations using a wireless network of low-cost sensors in households using solid fuels. (United States)

    Patel, Sameer; Li, Jiayu; Pandey, Apoorva; Pervez, Shamsh; Chakrabarty, Rajan K; Biswas, Pratim


    Many households use solid fuels for cooking and heating purposes. There is currently a knowledge gap in our understanding of the variations in indoor air quality throughout the household as most of the studies focus on the areas in the close proximity of the cookstove. A low-cost wireless particulate matter (PM) sensor network was developed and deployed in households in Raipur, India to establish the spatio-temporal variation of PM concentrations. The data from multiple sensors were acquired in real-time with a wireless system. Data collected from the sensors agreed well (R 2 =0.713) with the reference data collected from a commercially available instrument. Low spatial variability was observed within the kitchen due to its small size and poor ventilation - a common feature of most rural Indian kitchens. Due to insufficient ventilation from open doors and windows, high PM concentrations similar to those found in the kitchen were also found in the adjoining rooms. The same household showed significantly different post-extinguished cookstove PM concentration decay rates (0.26mg/m 3 -min and 0.87mg/m 3 -min) on different days, owing to varying natural air exchange rates (7.68m 3 /min and 37.40m 3 /min). Copyright © 2016 Elsevier Inc. All rights reserved.

  7. Why solid-state fermentation is more advantageous over submerged fermentation for converting high concentration of glycerol into Monacolin K by Monascus purpureus 9901: A mechanistic study. (United States)

    Zhang, Bo-Bo; Lu, Li-Ping; Xu, Gan-Rong


    The underlying mechanisms by which solid-state fermentation (SSF) was more advantageous over submerged fermentation (SmF) for converting high concentration of glycerol into Monacolin K by Monascus purpureus were investigated innovatively. First, the established kinetic models and kinetic parameters showed that the cell growth, Monacolin K formation and glycerol consumption in SSF were more rapid than those in SmF. Secondly, the comparison of fatty acid composition of mycelial cells indicated a better fluidity and permeability of the cell membrane in SSF than that of SmF, which was also consistent with the difference in the ratio of extracellular/intracellular Monacolin K between the two systems. Thirdly, the phenomenon of glycerol concentration gradient was verified in SSF, which could well explain the resistance effect to high concentration of glycerol in SSF. These new findings provide some important insights to the elucidation of the advantages of SSF for the synthesis of fungal secondary metabolites. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Concentration and sources of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) in surface soil near a municipal solid waste (MSW) landfill. (United States)

    Melnyk, A; Dettlaff, A; Kuklińska, K; Namieśnik, J; Wolska, L


    Due to a continuous demand of land for infrastructural and residential development there is a public concern about the condition of surface soil near municipal solid waste landfills. A total of 12 surface (0-20 cm) soil samples from a territory near a landfill were collected and the concentration of 16 PAHs and 7 PCB congeners were investigated in these samples. Limits of detection were in the range of 0.038-1.2 μg/kg for PAHs and 0.025-0.041 μg/kg for PCBs. The total concentration of ∑ PAHs ranged from 892 to 3514 μg/kg with a mean of 1974 μg/kg. The total concentration of ∑ PCBs ranged from 2.5 to 12 μg/kg with a mean of 4.5 μg/kg. Data analyses allowed to state that the PAHs in surface soils near a landfill were principally from pyrogenic sources. Due to air transport, PAHs forming at the landfill are transported outside the landfill. PCB origin is not connected with the landfill. Aroclor 1242 can be the source of PCBs in several samples. Copyright © 2015. Published by Elsevier B.V.

  9. Determining annual suspended sediment and sediment-associated trace element and nutrient fluxes (United States)

    Horowitz, A.J.


    Suspended sediment is a major factor in the biological and geochemical cycling of trace elements and nutrients in aquatic systems. The design of effective studies involving the collection, processing, and subsequent chemical analysis of suspended sediment requires a clear understanding of the problems associated with using this sample medium. This review summarizes the current state of knowledge relative to the various issues/problems associated with the collection of representative suspended sediment samples in fluvial systems. It also addresses issues associated with accurately determining the concentrations and fluxes of sediment-associated trace elements and nutrients.

  10. [Light absorption by suspended particulate matter in Chagan Lake, Jilin]. (United States)

    Wang, Yuan-Dong; Liu, Dian-Wei; Song, Kai-Shan; Zhang, Bai; Wang, Zong-Ming; Jiang, Guang-Ji; Tang, Xu-Guang; Lei, Xiao-Chun; Wu, Yan-Qing


    Spectral characteristics and the magnitudes of light absorption by suspended particulate matter were determined by spectrophotometry in this optically complex Lake Chagan waters for the purpose of surveying the natural variability of the absorption coefficients to parameterize the bio-optical models for converting satellite or in-situ water reflectance signatures into water quality information. Experiments were carried out on seasonal frozen Lake Chagan, one representative inland case-2 water body in Northeast of China. Particulate absorption properties analyzed using the field data on July 15th and October 12th 2009 were measured using the quantitative filter technique to produce absorption spectra containing several fractions that could be attributed to two main optical active constituents (OACs) phytoplankton pigments and non-algal particulates (mineral sediments, and organic detritus). Results suggested that the suspended particulate matter (SPM) concentration was higher while phytoplankton biomass (chlorophyll-a concentration) was lower in July and that in October. The spectral shape of total suspended particulate matter resembled that of non-algal particulates which contributed greater than phytoplankton in total particulate absorption during both periods. An obvious absorption peak occurring at around 440 nm exhibited an increase in phytoplankton contribution in October. Non-algal particulate absorption at 440 nm (a(NAP) (440)) had better correlation with total suspended particulate matter concentration than that with chlorophyll-a over the two periods. Light absorption by phytoplankton pigments in the Chagan lake region was generally lower than that of non-algal components. Chl. a dominating phytoplankton pigment composition functioned exponentially with its absorption coefficients at 440 and 675 nm specifically, the average values of which in July were 0.146 8 m2 x mg(-1) and 0.050 3 respectively while in October they were 0.153 3 and 0.013 2 m2 x mg(-1

  11. Separation and Pre-concentration of Cadmium, Copper, Lead, Nickel and Zinc by Solid-Liquid Extraction of their Cocrystallized Naphthalene Dithizone Chelate in Saline Matrices

    Directory of Open Access Journals (Sweden)

    Costa Antônio C. Spínola


    Full Text Available A procedure for separation and pre-concentration of trace amounts of cadmium, copper, lead, nickel, and zinc in brine samples has been proposed. It is based on the adsorption of metal ions onto dithizone co-crystallized with microcrystalline naphthalene, in the pH range 8.5-9.1. Nitric acid is used to back-extract the cations from the solid phase, which are measured by ICP-OES. Various parameters, such as the effect of pH, stirring time, and amounts of solid phase, have been studied in detail, to optimize the conditions for the determination of trace amounts of Cd, Cu, Pb, Ni and Zn in synthetic brine samples. The limits of detection values expressed in mug L-1 are 44 (Zn, 11 (Ni, 30 (Cd, 47 (Pb and 11 (Cu. The precision of the procedure was determined by running 10 replicate samples, each one containing 250 mug L-1 of each element and the relative standard deviations were 2.71 % (Cd, 2.15 % (Cu, 1.53 % (Pb, 2.47 % (Ni, and 2.78 % (Zn. The accuracy of the procedure was confirmed by applying the analyte additions method and the results indicated that quantitative recoveries (superscript three 95 % were obtained.

  12. Low-temperature (<200 oC solid-phase crystallization of high substitutional Sn concentration (∼10% GeSn on insulator enhanced by weak laser irradiation

    Directory of Open Access Journals (Sweden)

    Kenta Moto


    Full Text Available Low temperature (8% on insulating substrates is essential to realize next generation flexible electronics. To achieve this, a growth method of high quality GeSn films on insulating substrates by combination of laser irradiation and subsequent thermal annealing is developed. Here, the laser fluence is chosen as weak, which is below the critical fluence for crystallization of GeSn. It is clarified that for samples irradiated with weak laser fluence, complete crystallization of GeSn films is achieved by subsequent thermal annealing at ∼170 oC without incubation time. In addition, the quality of GeSn films obtained by this method is higher compared with conventional growth techniques such as melting growth by pulsed laser annealing or solid-phase crystallization (SPC without pre-laser irradiation. Substitutional Sn concentrations in the grown layers estimated by Raman spectroscopy measurements are 8-10%, which far exceed thermal equilibrium solid-solubility of Sn in Ge (∼2%. These phenomena are explained by generation of a limited number of nuclei by weak laser irradiation and lateral SPC by subsequent thermal annealing. This method will facilitate realization of next-generation high performance devices on flexible insulating substrates.

  13. Continuous-flow centrifugation to collect suspended sediment for chemical analysis (United States)

    Conn, Kathleen E.; Dinicola, Richard S.; Black, Robert W.; Cox, Stephen E.; Sheibley, Richard W.; Foreman, James R.; Senter, Craig A.; Peterson, Norman T.


    Recent advances in suspended-sediment monitoring tools and surrogate technologies have greatly improved the ability to quantify suspended-sediment concentrations and to estimate daily, seasonal, and annual suspended-sediment fluxes from rivers to coastal waters. However, little is known about the chemical composition of suspended sediment, and how it may vary spatially between water bodies and temporally within a single system owing to climate, seasonality, land use, and other natural and anthropogenic drivers. Many water-quality contaminants, such as organic and inorganic chemicals, nutrients, and pathogens, preferentially partition in sediment rather than water. Suspended sediment-bound chemical concentrations may be undetected during analysis of unfiltered water samples, owing to small water sample volumes and analytical limitations. Quantification of suspended sediment‑bound chemical concentrations is needed to improve estimates of total chemical concentrations, chemical fluxes, and exposure levels of aquatic organisms and humans in receiving environments. Despite these needs, few studies or monitoring programs measure the chemical composition of suspended sediment, largely owing to the difficulty in consistently obtaining samples of sufficient quality and quantity for laboratory analysis.A field protocol is described here utilizing continuous‑flow centrifugation for the collection of suspended sediment for chemical analysis. The centrifuge used for development of this method is small, lightweight, and portable for the field applications described in this protocol. Project scoping considerations, deployment of equipment and system layout options, and results from various field and laboratory quality control experiments are described. The testing confirmed the applicability of the protocol for the determination of many inorganic and organic chemicals sorbed on suspended sediment, including metals, pesticides, polycyclic aromatic hydrocarbons, and

  14. Normalization of glucose concentrations and deceleration of gastric emptying after solid meals during intravenous glucagon-like peptide 1 in patients with type 2 diabetes

    DEFF Research Database (Denmark)

    Meier, Juris J; Gallwitz, Baptist; Salmen, Stefan


    measures ANOVA and Duncan's post hoc test. Plasma glucose concentrations were equally normalized with all GLP-1 doses (P ...The effects of different i.v. doses of glucagon-like peptide 1 (GLP-1) on glucose homeostasis and gastric emptying were compared in patients with type 2 diabetes. Twelve patients with type 2 diabetes received three different infusion rates of GLP-1 (0.4, 0.8, and 1.2 pmol/kg x min) or placebo...... in the fasting state and after a solid test meal (containing [(13)C]octanoic acid). Blood was drawn for glucose, insulin, C-peptide, glucagon, and GLP-1 determinations. The gastric emptying rate was calculated from the (13)CO(2) excretion rates in breath samples. Statistics were determined using repeated...


    Energy Technology Data Exchange (ETDEWEB)

    Bamberger, Judith A.; Greenwood, Margaret S.; Lawler, Bruce D.; Sundaram, S. K.; Baer, Ellen BK; Hatchell, Brian K.; Hopkins, Derek F.; Kirihara, Leslie J.; Pekour, Mikhail S.; Sande, Susan; Yu, Xiao-Ying; Zuljevic, Nino


    Pulse jet mixing tests to suspend noncohesive solids in Newtonian liquid were conducted at three geometric scales. To understand the solids suspension process an ultrasonic concentration probe was used to measure the concentration of solids in the cloud during a pulse at various elevations and radial positions. The data are being analyzed to provide a model for predicting concentration as a function of elevation. This paper presents a simple single frequency ultrasonic measurement application that demonstrates the ability of ultrasonic sensors to measure slurry concentration based on signal attenuation. Sensor calibration data show that ultrasonic signal attenuation is proportional to the applied frequency and to the slurry volume fraction. Real-time measurements of ultrasonic signal attenuation were used to track the process of slurry mixing using single sensors and sensor arrays. Comparison of means of the ultrasonic measurements with means obtained from discrete extractive measurements show that the distributions overlap and cannot be statistically distinguished. The real-time ultrasonic sensor can be used as a primary measurement method or to reduce reliance upon extractive methods to measure slurry density.

  16. The chemistry of suspended particulate material in a highly contaminated embayment of Port Jackson (Australia) under quiescent, high-wind and heavy-rainfall conditions (United States)

    Birch, Gavin; O'Hea, Laura


    This study investigated physico-chemical characteristics of the water column and chemistry of suspended particulate material (SPM) under quiescent, high-wind and high-wind/heavy-rainfall conditions in Homebush Bay, a highly contaminated embayment of Port Jackson (Australia) to distinguish source and possible adverse effects to benthic and pelagic animals. Mean concentrations in surficial sediment were chemistry indicated these metals had multiple sources, i.e. the estuary, stormwater and industry. Mean total suspended solids (TSS) were 7, 17 and 20 mg L-1 during quiescent, high-rainfall and heavy rainfall/high wind conditions, respectively, whereas SPM Cd, Co, Cr, Cu, Ni, Pb and Zn concentrations varied between 13-25, 166-259, 127-198, 38-82, 236-305 and 605-865 μg g-1, respectively under these conditions. TSS and total water metal concentrations were lowest during quiescent conditions. High TSS and metal loads in surface water characterised high-rainfall events. Wind-induced resuspension contributed the greatest mass of SPM and metals to the water column. Benthic animals may be adversely affected by Pb and Zn in sediment. Total water Cu and Zn concentrations may pose a risk to filter-feeding animals in the water column due to resuspension of contaminated sediment.

  17. Magnetically suspended virtual divergent channel

    Energy Technology Data Exchange (ETDEWEB)

    Yamane, Ryuichiro [Kokushikan University, 4-28-1 Setagaya, Setagaya-ku, Tokyo 154-8515 (Japan)]. E-mail:; Oshiama, Shuzo [Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo 152-8552 (Japan); Park, Myeong-Kwan [Pusan National University, 30 Changjeon-dong, Kumjeong-ku, Pusan 609-735 (Korea, Republic of)


    Two permanent magnets are set face-to-face and inclined with each other to produce the long cuspidal magnetic field. The diamagnetic liquid is levitated and flows through it without contact with the solid walls as if it is in the virtual divergent channel. Analysis is made on the shape of the virtual channel, and the results are compared with the experimental ones. The divergence angle increases with the increase in the inclination of the magnets.

  18. Long-term continuous acoustical suspended-sediment measurements in rivers - Theory, application, bias, and error (United States)

    Topping, David J.; Wright, Scott A.


    It is commonly recognized that suspended-sediment concentrations in rivers can change rapidly in time and independently of water discharge during important sediment‑transporting events (for example, during floods); thus, suspended-sediment measurements at closely spaced time intervals are necessary to characterize suspended‑sediment loads. Because the manual collection of sufficient numbers of suspended-sediment samples required to characterize this variability is often time and cost prohibitive, several “surrogate” techniques have been developed for in situ measurements of properties related to suspended-sediment characteristics (for example, turbidity, laser-diffraction, acoustics). Herein, we present a new physically based method for the simultaneous measurement of suspended-silt-and-clay concentration, suspended-sand concentration, and suspended‑sand median grain size in rivers, using multi‑frequency arrays of single-frequency side‑looking acoustic-Doppler profilers. The method is strongly grounded in the extensive scientific literature on the incoherent scattering of sound by random suspensions of small particles. In particular, the method takes advantage of theory that relates acoustic frequency, acoustic attenuation, acoustic backscatter, suspended-sediment concentration, and suspended-sediment grain-size distribution. We develop the theory and methods, and demonstrate the application of the method at six study sites on the Colorado River and Rio Grande, where large numbers of suspended-sediment samples have been collected concurrently with acoustic attenuation and backscatter measurements over many years. The method produces acoustical measurements of suspended-silt-and-clay and suspended-sand concentration (in units of mg/L), and acoustical measurements of suspended-sand median grain size (in units of mm) that are generally in good to excellent agreement with concurrent physical measurements of these quantities in the river cross sections at

  19. Remote Sensing of Suspended Sediment Dynamics in the Mississippi Sound (United States)

    Merritt, D. N.; Skarke, A. D.; Silwal, S.; Dash, P.


    The Mississippi Sound is a semi-enclosed estuary between the coast of Mississippi and a chain of offshore barrier islands with relatively shallow water depths and high marine biodiversity that is wildly utilized for commercial fishing and public recreation. The discharge of sediment-laden rivers into the Mississippi Sound and the adjacent Northern Gulf of Mexico creates turbid plumes that can extend hundreds of square kilometers along the coast and persist for multiple days. The concentration of suspended sediment in these coastal waters is an important parameter in the calculation of regional sediment budgets as well as analysis of water-quality factors such as primary productivity, nutrient dynamics, and the transport of pollutants as well as pathogens. The spectral resolution, sampling frequency, and regional scale spatial domain associated with satellite based sensors makes remote sensing an ideal tool to monitor suspended sediment dynamics in the Northern Gulf of Mexico. Accordingly, the presented research evaluates the validity of published models that relate remote sensing reflectance with suspended sediment concentrations (SSC), for similar environmental settings, with 51 in situ observations of SSC from the Mississippi Sound. Additionally, regression analysis is used to correlate additional in situ observations of SSC in Mississippi Sound with coincident observations of visible and near-infrared band reflectance collected by the Moderate Resolution Imaging Spectroradiometer (MODIS) sensor aboard the Aqua satellite, in order to develop a site-specific empirical predictive model for SSC. Finally, specific parameters of the sampled suspended sediment such as grain size and mineralogy are analyzed in order to quantify their respective contributions to total remotely sensed reflectance.

  20. Concentration, partial characterization, and immobilization of lipase extract from P. brevicompactum by solid-state fermentation of babassu cake and castor bean cake. (United States)

    Silva, Marceli Fernandes; Freire, Denise M G; de Castro, Aline Machado; Di Luccio, Marco; Mazutti, Marcio A; Oliveira, J Vladimir; Treichel, Helen; de Oliveira, Débora


    One relevant limitation hindering the industrial application of microbial lipases has been attributed to their production cost, which is determined by the production yield, enzyme stability among other. The objective of this work was to evaluate the concentration and immobilization of lipase extracts from Penicillium brevicompactum obtained by solid-state fermentation of babassu cake and castor bean cake. The precipitation with ammonium sulfate 60% of saturation of crude extract obtained with babassu cake as raw material showed an enhancement in hydrolytic and esterification activities from 31.82 to 227.57 U/g and from 170.92 to 207.40 U/g, respectively. Concentrated lipase extracts showed preference to medium-chain triglycerides and fatty acids. It is shown that the enzyme activity is maintained during storage at low temperatures (4 and -10°C) for up to 30 days. Higher esterification activities were achieved when the lipase extract was immobilized in sodium alginate and activated coal.

  1. Aerial Photo Utilization in Estimating Suspended Sediment in the Wuryantoro Watershed, Wonogiri

    Directory of Open Access Journals (Sweden)

    Sugiharto Budi Santoso


    Full Text Available Suspended sediment load flowing out from a watershed is normally predicated by analysis os suspended sediment of water sample, and the volume of suspended sediment be calculated based on sediment concentration and river discharge. Such field measurements need a lot of field data and they are time consuming. Another method for prediction of suspended sediment by using remote sensing imagery data and recorded rainfall data. The objective of this research is to 1 examine the capability of remote sensing technique to obtain the parameters of the physical data of land in the prediction of suspended sediment; 2 examine the accuracy of the model for prediction suspended sediment. This research is carried out in Wuryantoro watershed, Wonogiri. The main data to obtain the parameters of the physical data of land is infrared aerial photograph on scale 1 : 10.000. the method that used in this research is interpretation of remote sensing imagery data, combined with rainfall data. The result show that the accuracy of landuse is 88.5%, the accuracy of slope is 87.67%. the accuracy of the prediction of suspended sediment by model A3 87.07%, model C1 86.63%, model C2 90.57%, model A8 84.13%, model A9 80.1%, and model C4 78.6%.

  2. The effects of sample scheduling and sample numbers on estimates of the annual fluxes of suspended sediment in fluvial systems (United States)

    Horowitz, Arthur J.; Clarke, Robin T.; Merten, Gustavo Henrique


    Since the 1970s, there has been both continuing and growing interest in developing accurate estimates of the annual fluvial transport (fluxes and loads) of suspended sediment and sediment-associated chemical constituents. This study provides an evaluation of the effects of manual sample numbers (from 4 to 12 year−1) and sample scheduling (random-based, calendar-based and hydrology-based) on the precision, bias and accuracy of annual suspended sediment flux estimates. The evaluation is based on data from selected US Geological Survey daily suspended sediment stations in the USA and covers basins ranging in area from just over 900 km2 to nearly 2 million km2 and annual suspended sediment fluxes ranging from about 4 Kt year−1 to about 200 Mt year−1. The results appear to indicate that there is a scale effect for random-based and calendar-based sampling schemes, with larger sample numbers required as basin size decreases. All the sampling schemes evaluated display some level of positive (overestimates) or negative (underestimates) bias. The study further indicates that hydrology-based sampling schemes are likely to generate the most accurate annual suspended sediment flux estimates with the fewest number of samples, regardless of basin size. This type of scheme seems most appropriate when the determination of suspended sediment concentrations, sediment-associated chemical concentrations, annual suspended sediment and annual suspended sediment-associated chemical fluxes only represent a few of the parameters of interest in multidisciplinary, multiparameter monitoring programmes. The results are just as applicable to the calibration of autosamplers/suspended sediment surrogates currently used to measure/estimate suspended sediment concentrations and ultimately, annual suspended sediment fluxes, because manual samples are required to adjust the sample data/measurements generated by these techniques so that they provide depth-integrated and cross

  3. Assessment of CO, CO2 and Suspended Particulate Matter Emissions

    Directory of Open Access Journals (Sweden)

    Bala Isah ABDULKARIM


    Full Text Available The concentrations of carbon oxides (CO and CO2 and suspended particulate matter at Benue Cement Company (BCC and Tse-Kucha community was investigated. Results obtained, shows that concentrations of carbon dioxide of 34.40ppm, 39.50 ppm, 48.50 ppm, 78.55 ppm, 65.25 ppm, 26.80 ppm and 29.5 ppm for quarry, raw mill, cement mill, Kiln, packing house, limestone stockpile and Tse-Kucha community respectively were below the maximum standard natural concentration of CO2 in atmosphere of 600ppm while concentrations of CO (1.25ppm - 4.00ppm measured in all the sample stations were below the Nigerian Ambient Air Quality Standards (NAAQS and WHO max limit of 10 ppm - 20 ppm for an 8-hourly average time. Lastly, the concentrations of suspended particulate matter of 375 μg/m3, 338 μg/m3 and 290 μg/m3 at the cement mill, packing house and raw mill respectively were also above the World Health Organization’s (WHO’s Guidelines and Standards for Ambient Air Quality which stipulates a range of 150 μg/m3 to 230 μg/m3 for a 24- hourly average.

  4. Method development for the concentration determination of a protein in human plasma utilizing 96-well solid-phase extraction and liquid chromatography/tandem mass spectrometric detection. (United States)

    Ji, Qin C; Gage, Eric M; Rodila, Ramona; Chang, Min S; El-Shourbagy, Tawakol A


    Although liquid chromatography/tandem mass spectrometry (LC/MS/MS) technology has been widely used for quantitative analysis of small organic molecules, it has been a challenging task to quantitatively analyze protein samples utilizing this technology in biological matrices for pre-clinical and clinical studies. Here we present our initial results in method development for the quantitative determination of rK5 protein concentrations in human plasma samples utilizing LC/MS/MS technology. A protein similar in structure to rK5, but with a slightly reduced molecular weight, was used as internal standard. A 96-well solid-phase extraction procedure was developed to effectively extract protein analytes from plasma samples. Quantitative analysis was obtained by a novel approach of protein monitoring that employed selective reaction monitoring (SRM). Even though mass spectrometry of the internal standard protein gave no fragment ions, SRM monitoring greatly reduced background interference. Using samples prepared in human plasma with sodium EDTA as anticoagulant, a correlation coefficient (r(2)) of 0.9940 was obtained by producing a single standard curve with the injection of six rows of standards with a concentration range from 100 ng/mL to 10 microg/mL. The mean analytical recovery for these standards ranged from 91.5 to 103.6%. The CVs for individual standard levels ranged from 3.7 to 20.9%. The experiment was also repeated using samples prepared in human plasma with sodium heparin as anticoagulant, which produced a correlation coefficient (r(2)) of 0.9952 obtained from a single standard curve with the injection of four rows of standards with a concentration range from 50 ng/mL to 10 microg/mL. The mean analytical recovery for the standards ranged from 96.2 to 104.6%. The CVs for individual standard levels ranged from 2.6 to 15.6%. Copyright 2003 John Wiley & Sons, Ltd.

  5. Matrix solid-phase dispersion on column clean-up/pre-concentration as a novel approach for fast isolation of abuse drugs from human hair. (United States)

    Míguez-Framil, Martha; Moreda-Piñeiro, Antonio; Bermejo-Barrera, Pilar; Alvarez-Freire, Iván; Tabernero, María Jesús; Bermejo, Ana María


    A simple and fast sample pre-treatment method based on matrix solid-phase dispersion (MSPD) for isolating cocaine, benzoylecgonine (BZE), codeine, morphine and 6-monoacethylmorphine (6-MAM) from human hair has been developed. The MSPD approach consisted of using alumina (1.80 g) as a dispersing agent and 0.6M hydrochloric acid (4 mL) as an extracting solvent. For a fixed hair sample mass of 0.050 g, the alumina mass to sample mass ratio obtained was 36. A previously conditioned Oasis HLB cartridge (2 mL methanol, plus 2 mL ultrapure water, plus 1 mL of 0.2M/0.2M sodium hydroxide/boric acid buffer solution at pH 9.2) was attached to the end of the MSPD syringe for on column clean-up of the hydrochloric acid extract and for transferring the target compounds to a suitable solvent for gas chromatography (GC) analysis. Therefore, the adsorbed analytes were directly eluted from the Oasis HLB cartridges with 2 mL of 2% acetic acid in methanol before concentration by N(2) stream evaporation and dry extract derivatization with N-methyl-tert-butylsilyltrifluoroacetamide (BSTFA) and chlorotrimethylsilane (TMCS). The optimization/evaluation of all the factors affecting the MSPD and on column clean-up procedures has led to a fast sample treatment, and analytes extraction and pre-concentration can be finished in approximately 30 min. The developed method has been applied to eight hair samples from poli-drug abusers and measured analyte concentrations have been found to be statistically similar (95% confidence interval) to those obtained after a conventional enzymatic hydrolysis method (Pronase E). Copyright © 2010. Published by Elsevier B.V.

  6. A novel solid-phase extraction for the concentration of sweeteners in water and analysis by ion-pair liquid chromatography-triple quadrupole mass spectrometry. (United States)

    Gan, Zhiwei; Sun, Hongwen; Wang, Ruonan; Feng, Biting


    A highly sensitive method for the simultaneous trace (ng/L) quantification of seven commonly used artificial sweeteners in a variety of water samples using solid-phase extraction and ion-pair high-performance liquid chromatography (HPLC) triple quadrupole mass spectrometer with an electrospray ionization source (ESI-MS) in negative ion multiple reaction monitoring mode was developed. Ten solid phase extraction (SPE) cartridges were tested to evaluate their applicability for the pre-concentration of the analytes, and their loading and eluting parameters were optimized. Satisfactory recoveries (77-99%) of all of the studied sweeteners were obtained using a Poly-Sery PWAX cartridge with 25 mM sodium acetate solution (pH 4) as wash buffer and methanol containing 1mM tris (hydroxymethyl) amino methane (TRIS) as eluent. The method is sound and does not require pH adjustment or buffering of water samples. The HPLC separation was performed on an Athena C18-WP column with water and acetonitrile, both containing 5mM ammonium acetate and 1mM TRIS as mobile phases, in gradient elution mode. The linearity, precision, and accuracy of the method were evaluated, and good reproducibility was obtained. Method quantification limits varied between 0.4 and 7.5 ng/L for different water samples. The post-extraction spike method was applied to assess matrix effects, and quantification was achieved using internal standard calibration to overcome the unavoidable matrix effects during ESI-MS analysis. The method was applied to the analysis of thirteen water samples from Tianjin, China, including wastewater, tap water, surface water, and groundwater. The method described here is time-saving, accurate and precise, and is suitable for monitoring artificial sweeteners in different water matrices. Copyright © 2012 Elsevier B.V. All rights reserved.

  7. The mineralogy and trace element constituents of suspended stream sediments of the Linggi River Basin, Malaysia (United States)

    Nather Khan, I. S. A.

    The mineralogy and trace element concentrations of suspended stream sediments were determined at selected stations in the Linggi River Basin, Malaysia, while conducting an intensive study on water quality and a biological assessment of water pollution in the basin. The minerals that were identified from the X-ray patterns of the suspended stream sediments are kaolinite, mica, feldspar and quartz. Kaolinite was the most abundant mineral, followed by mica. By considering mean concentrations of various trace elements, aluminum and manganese were the most abundant elements. Higher concentrations of copper and zinc at some stations were due to pollutants from the nearby Senawang Industrial Estate.

  8. Suspended and Bedload Sand dynamics in the Mekong River Channel and Export to the Coastal Ocean (United States)

    Stephens, J. D.; Di Leonardo, D. R.; Weathers, H. D., III; Allison, M. A.


    Two field campaigns were conducted in the tidal and estuarine reach of the Song Hau distributary of the Mekong River to examine the dynamics of sand transport and export to the coastal ocean. This study examines variation in suspended sand concentration and net transport with respect to changes in discharge between the October 2014 high discharge and March 2015 low discharge studies, and over semi-diurnal and spring-neap tidal cycles between Can Tho and the Tran De and Dinh An distributary channels in the Mekong Delta. Suspended sand concentrations were measured using a P-61 isokinetic suspended sediment sampler and a Sequoia Scientific LISST-100X used in vertical profiling mode. Stationary ADCP data are used to examine bed stress at cast sites. Bed load transport rates were calculated using a repeat multibeam transect methodology and dune translation rates with flow. Preliminary results indicate that suspended sand concentration increases towards the bed and is positively correlated with increasing shear stress controlled by river discharge and tides. However, sites with non-sandy bottoms, as indicated by multibeam bathymetry, have low suspended sand concentrations, suggesting a close linkage with a bed sand source. Bed load transport rates vary cross-sectionally with shear stress and are linked to dune size. Most bed load transport is taking place in or near the thalweg. The reduction in ebb flows at low discharge and the mantling of sand fields by salinity driven mud deposition, is suspected to control the low suspended sand concentrations observed in March. Results to date suggest that net sand export (suspended plus bed load) to the ocean occurs predominantly during the high discharge monsoon season.

  9. Evaluation of Spinacia oleracea L. leaves mucilage as an innovative suspending agent. (United States)

    Nayak, Amit Kumar; Pal, Dilipkumar; Pany, Dipti Ranjan; Mohanty, Biswaranjan


    The present study was undertaken to evaluate the mucilage isolated from Spinacia oleracea L. leaves, commonly named spinach (family: Amaranthaceae) as an innovative suspending agent. Zinc oxide suspensions (20% w/v) were prepared using the mucilage of S. oleracea L. leaves as a suspending agent, and it was evaluated for its stability by using parameters like, sedimentation profile, degree of flocculation, and redispersibility. The effect of the tested mucilage on the suspension was compared with various commonly used suspending agents, such as, tragacanth, bentonite, and sodium carboxymethyl cellulose (NaCMC) at concentrations of 0.5, 1.0, and 2.0% w/v. The results obtained indicated that the mucilage of S. oleracea L. leaves could be used as a suspending agent, and the performance was found to be superior to both tragacanth and bentonite.

  10. Evaluation of Spinacia oleracea L. leaves mucilage as an innovative suspending agent

    Directory of Open Access Journals (Sweden)

    Amit Kumar Nayak


    Full Text Available The present study was undertaken to evaluate the mucilage isolated from Spinacia oleracea L. leaves, commonly named spinach (family: Amaranthaceae as an innovative suspending agent. Zinc oxide suspensions (20% w/v were prepared using the mucilage of S. oleracea L. leaves as a suspending agent, and it was evaluated for its stability by using parameters like, sedimentation profile, degree of flocculation, and redispersibility. The effect of the tested mucilage on the suspension was compared with various commonly used suspending agents, such as, tragacanth, bentonite, and sodium carboxymethyl cellulose (NaCMC at concentrations of 0.5, 1.0, and 2.0% w/v. The results obtained indicated that the mucilage of S. oleracea L. leaves could be used as a suspending agent, and the performance was found to be superior to both tragacanth and bentonite.

  11. Optimal control of suspended sediment distribution model of Talaga lake (United States)

    Ratianingsih, R.; Resnawati, Azim, Mardlijah, Widodo, B.


    Talaga Lake is one of several lakes in Central Sulawesi that potentially to be managed in multi purposes scheme because of its characteristic. The scheme is addressed not only due to the lake maintenance because of its sediment but also due to the Algae farming for its biodiesel fuel. This paper governs a suspended sediment distribution model of Talaga lake. The model is derived from the two dimensional hydrodynamic shallow water equations of the mass and momentum conservation law of sediment transport. An order reduction of the model gives six equations of hyperbolic systems of the depth, two dimension directional velocities and sediment concentration while the bed elevation as the second order of turbulent diffusion and dispersion are neglected. The system is discreted and linearized such that could be solved numerically by box-Keller method for some initial and boundary condition. The solutions shows that the downstream velocity is play a role in transversal direction of stream function flow. The downstream accumulated sediment indicate that the suspended sediment and its changing should be controlled by optimizing the downstream velocity and transversal suspended sediment changing due to the ideal algae growth need.

  12. Dispersion of suspended material from an operating sand suction dredge in the Øresund (Denmark)

    DEFF Research Database (Denmark)

    Kiørboe, Thomas; Møhlenberg, F.


    The concentration of suspended material in the immediate vicinity of an operating sand suction dredge in the Oresund was 3-5000mg/l. Concentrations > 100 mg/l were restricted to a downstream distance of .apprx. 150m and ambient levels were reached within .apprx. 1 km of the dredge. The natural va...

  13. Effects of suspended sediment on the development and hatching of herring (Clupea harengus) eggs

    DEFF Research Database (Denmark)

    Kiørboe, Thomas; Frantsen, Erik; Jensen, Carsten


    Eggs of herring artificially fertilized in the laboratory, were exposed either to different constant concentrations of suspended silt (about 5-300 mg 1** minus **1) or to short-term high concentration (500 mg 1** minus **1) at different times during embryonic development. These experiments were...

  14. Suspended sediment transport around a large-scale laboratory breaker bar

    NARCIS (Netherlands)

    van der Zanden, Joep; van der A, D.A.; Hurther, D.; Caceres, I.; O' Donoghue, T.; Ribberink, Jan S.


    This paper presents novel insights into suspended sediment concentrations and fluxes under a large-scale laboratory plunging wave. Measurements of sediment concentrations and velocities were taken at 12 locations around an evolving breaker bar, covering the complete breaking region from shoaling to

  15. Levels of As, Pb, Cd and Fe in Suspended Particulate Matter (SPM ...

    African Journals Online (AJOL)

    Suspended Particulate Matter (SPM) collected from three different artisans' workshops was analyzed for As, Cd, Pb and Fe by Atomic Absorption Spectrophotometry (AAS). The range of SPM concentrations for the three workshops was 583-20,166Bg/m3. The highest concentrations of these elements were observed in Motor ...

  16. Effects of cadmium accumulation from suspended sediments and phytoplankton on the Oyster Saccostrea glomerata

    Energy Technology Data Exchange (ETDEWEB)

    Schmitz, Helena A.; Maher, William A., E-mail:; Taylor, Anne M.; Krikowa, Frank


    Highlights: • Saccostrea glomerata accumulated cadmium from sediments and phytoplankton. • Effects were similar for both pathways. • Antioxidant capacity, lipid peroxidation and lysosomal destabilisation were affected. • Clear exposure–dose–response relationships were demonstrated. - Abstract: Metals are accumulated by filter feeding organisms via water, ingestion of suspended sediments or food. The uptake pathway can affect metal toxicity. Saccostrea glomerata were exposed to cadmium through cadmium-spiked suspended sediments (19 and 93 μg/g dry mass) and cadmium-enriched phytoplankton (1.6–3 μg/g dry mass) and cadmium uptake and effects measured. Oysters accumulated appreciable amounts of cadmium from both low and high cadmium spiked suspended sediment treatments (5.9 ± 0.4 μg/g and 23 ± 2 μg/g respectively compared to controls 0.97 ± 0.05 μg/g dry mass). Only a small amount of cadmium was accumulated by ingestion of cadmium-enriched phytoplankton (1.9 ± 0.1 μg/g compared to controls 1.2 ± 0.1 μg/g). In the cadmium spiked suspended sediment experiments, most cadmium was desorbed from sediments and cadmium concentrations in S. glomerata were significantly related to dissolved cadmium concentrations (4–21 μg/L) in the overlying water. In the phytoplankton feeding experiment cadmium concentrations in overlying water were <0.01 μg/L. In both exposure experiments, cadmium-exposed oysters showed a significant reduction in total antioxidant capacity and significantly increased lipid peroxidation and percentage of destabilised lysosomes. Destabilised lysosomes in the suspended sediments experiments also resulted from stress of exposure to the suspended sediments. The study demonstrated that exposure to cadmium via suspended sediments and to low concentrations of cadmium through the ingestion of phytoplankton, can cause sublethal stress to S. glomerata.

  17. Solid/liquid partition coefficients (K{sub d}) and plant/soil concentration ratios (CR) for selected soils, tills and sediments at Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Sheppard, Steve (ECOMatters Inc. (Canada)); Sohlenius, Gustav (Sveriges geologiska undersoekning (Sweden)); Omberg, Lars-Gunnar (ALS Scandinavia AB (Sweden)); Borgiel, Mikael (Sveriges Vattenekologer AB (Sweden)); Grolander, Sara (Facilia AB (Sweden)); Norden, Sara (Svensk Kaernbraenslehantering AB (Sweden))


    Solid/liquid partition coefficients (K{sub d}) are used to indicate the relative mobility of radionuclides and elements of concern from nuclear fuel waste, as well as from other sources. To indicate the uptake of radionuclides in biota concentration ratios (CR) between soil and biota are used. This report summarized K{sub d} data for regolith and marine sediments based on concentrations of 69 indigenous stable elements measured from samples collected at the Forsmark site and CR data concerning cereals growing on these soils. The samples included 50 regolith samples from agricultural land and wetlands, 8 samples of till collected at different depths, and two marine sediment samples. In addition, cereal grains, stems and roots were collected from 4 sites for calculation of CRs. The regolith samples represented the major 5 deposits, which can be used as arable land, at the site (clayey till, glacial clay, clay gyttja and peat (cultivated and undisturbed)). K{sub d} values were generally lower for peat compared to clay soils. There were also clear differences in K{sub d} resulting from differences in soil chemistry within each regolith type. Soil pH was the most important factor, and K{sub d} values for many elements were lower in acidic clay soils compared to basic clay soils. Although there were only a few samples of sandy till and marine sediment, the K{sub d} values were generally consistent with the corresponding regolith K{sub d} values. Of the different cereal parts the grain always had the lowest CR. In most cases, the root CR was significantly higher than the grain CR, whereas only for a few elements were the grain and stem CR values different

  18. Solid sampling graphite furnace atomic absorption spectrometry for the direct analysis of microextraction solvent bars used for metal ultra-trace pre-concentration (United States)

    González-Álvarez, Rafael Jesús; Pinto, Juan J.; Bellido-Milla, Dolores; Moreno, Carlos


    The potential applicability of the continuum source solid sampling graphite furnace atomic absorption spectroscopy (CS SS-GF AAS) technique has been studied to carry out the direct analysis of microextraction solvent bars used for metal ultra-trace pre-concentration in natural waters. An optimisation of the temperature program was developed for this purpose. Preliminary chamber furnace studies were performed in order to understand the behaviour of the bars with the increasing temperature. Solvent bars were filled with an acceptor solution, impregnated with an organic extractant and placed into the chamber furnace to carry out several temperature programs. Results led to perform a correct optimisation of the drying and pyrolysis steps of the furnace temperature program, which was tested with silver once completed. Blank solvent bars as well as standards containing silver were measured, obtaining a calibration curve with a correlation coefficient of 0.991. The results exhibited good repeatability and reproducibility, with relative standard deviations below 10% in both cases, indicating a promising applicability of the CS SS-GF AAS technique to directly determine metallic species in microextraction solvent bars.

  19. Improved Friction and Wear of M50 Steel Composites Incorporated with ZnO as a Solid Lubricant with Different Concentrations Under Different Loads (United States)

    Essa, F. A.; Zhang, Qiaoxin; Huang, Xingjiu; Ibrahim, Ahmed Mohamed Mahmoud; Ali, Mohamed Kamal Ahmed; Abdelkareem, Mohamed A. A.; Elagouz, Ahmed


    This experimental study explores improving the tribological behavior of M50 steel using ZnO as a solid lubricant with different concentrations of 5, 10, 15, 20, and 25 wt.%. Tribological tests were conducted using pin-on-disk tribometer under different loads of 3, 6, 9, and 12 N and constant sliding speed of 0.2 m s-1 in air. XRD, EPMA, FESEM, EDS mapping, and XPS tests were performed to understand the major mechanisms leading to improve the tribological and mechanical properties of M50 composites. Results showed that the best tribological and mechanical properties were obtained at 20.0 wt.% of ZnO. Friction coefficient and wear rate were reduced by 52.909 and 70%, respectively, due to the formation of tribo-films on the worn surfaces. Furthermore, the hardness of M50 composites increased by 27.86%. Our study provides results with suggestions to overcome the challenges facing the technology when using M50 matrix composites in mechanical applications.

  20. Determination of traces of copper and zinc in honeys by the solid phase extraction pre-concentration followed by the flame atomic absorption spectrometry detection. (United States)

    Stecka, Helena; Jedryczko, Dominika; Welna, Maja; Pohl, Pawel


    A simple and fast solid phase extraction procedure was developed to pre-concentrate traces of Cu and Zn prior to their determination in honey samples by flame atomic absorption spectrometry. The sample preparation included dissolution of honey samples and the passage (at 20 ml/min) of resulting 10% m/v solutions (100 ml) through Dowex 50W × 8-400 resin beds in order to quantitatively retain Cu and Zn and separate them from the glucose and fructose matrix. Enriched Cu and Zn traces were recovered with 5.0 ml of a 3.0 mol/l HCl solution and quantified by flame atomic absorption spectrometry. The procedure proposed was used to analyze sixty nine commercially available and freshly ripened honey samples coming from the Lower Silesia region (Poland). It enabled to measure Cu and Zn within the range of 0.01-1.42 and 0.03-15.38 μg/g, respectively, with precision better than 4%. Accuracy, assessed on the basis of the recovery test and the comparison of results with those obtained using wet digestion and inductively coupled plasma optical emission spectrometry, was ranged from -4% to +6%. Detection limits of Cu and Zn achieved with this method were 5 and 7 ng/g, respectively.

  1. Effect of Iron Oxides (Ordinary and Nano and Municipal Solid Waste Compost (MSWC Coated Sulfur on Wheat (Triticum aestivum L. Plant Iron Concentration and Growth

    Directory of Open Access Journals (Sweden)

    S Mazaherinia


    Full Text Available Abstract A greenhouse study was conducted to compare the effects of ordinary iron oxide (0.02-0.06 mm and nano iron oxide (25-250 nm and five levels of both iron oxides (0, 0.05, 0.1, 0.5, and 1.0 %w/w and two levels of sulfurous granular compost (MSW (0 and 2% w/w on plant height, spike length, grain weight per spike, total plant dry matter weight and thousands grain weight of wheat. The experimental factors were combined in factorial arrangement in a completely randomized design with 3 replications. Results showed that nano iron oxide was superior over ordinary iron oxide in all parameters studied. Fe concentration, spike length, plant height, grain weight per spike, total plant dry weight and thousands grain weight showed increasing trend per increase in both of iron oxides levels. Also, all parameters studied in sulfurous granular compost (MSW treatment were superior over granular compost without sulfurous (MSW. This increase in all parameters were significantly higher when urban solid waste compost coated with sulfur coupled with nano iron oxide compared to urban sulfurous granular compost (MSW along with ordinary iron oxide. Keywords: Sulfurous granular compost (MSW, Nano and ordinary iron oxides, Wheat

  2. Finite Element Modeling of Suspended Particle Migration in Non-Newtonian Fluids

    Energy Technology Data Exchange (ETDEWEB)

    Altobelli, S.; Baer, T.; Mondy, L.; Rao, R.; Stephens, T.


    Shear-induced migration of particles is studied during the slow flow of suspensions of spheres (particle volume fraction {phi} = 0.50) in an inelastic but shear-thinning, suspending fluid in flow between counterrotating concentric cylinders, The conditions are such that nonhydrodynamic effects are negligible. The movement of particles away from the high shear rate region is more pronounced than in a Newtonian suspending liquid. We test a continuum constitutive model for the evolution of particle concentration in a flowing suspension proposed by Phillips et al. (1992) by using shear-thinning, suspending fluids. The fluid constitutive equation is Carreau-like in its shear-thinning behavior but also varies with the local particle concentration. The model is compared with the experimental data gathered with nuclear magnetic resonance (NMR) imaging.

  3. Introduction to suspended-sediment sampling (United States)

    Nolan, K. Michael; Gray, John R.; Glysson, G. Douglas


    Knowledge of the amount and timing of sediment transport in streams is important to those directly or indirectly responsible for developing and managing water and land resources. Such data are often used to judge the health of watershed and the success or failure of activities designed to mitigate adverse impacts of sediment on streams and stream habitats. This training class presents an introduction to methods currently used by the U.S. Geological Survey (USGS) to sample suspended-sediment concentrations in streams. The presentation is narrated, but you control the pace of the presentation. If the computer you are using can view 'MPEG' videos you will be able to take advantage of videos interspersed in the presentation. A test, found at the end of the presentation, can be taken to assess how well you understood the training material. The class, which is registered as class SW4416 with the National Training Center of the USGS, should take two or three hours to complete. In order to use the presentation provided via this Web page, you will need to download a large disc images (linked below) and 'burn' it to a blank CD-ROM using a CD-ROM recorder on your computer. The presentation will only run on a Windows-based personal computer (PC). The presentation was developed using Macromedia Director MX 20041 and is contained in the file 'SIR05-5077.exe' which should autolaunch. If it does not, the presentation can be started by double-clicking on the file name. A sound card and speakers are necessary to take advantage of narrations that accompany the presentation. Text of narrations is provided, if you are unable to listen to narrations. Instructions for installing and running the presentation are included in the file 'Tutorial.htm', which is on the CD. 1 Registered Trademark: Macromedia Incorporated

  4. A new protocol for the analysis of pharmaceuticals, pesticides, and hormones in sediments and suspended particulate matter from rivers and municipal wastewaters. (United States)

    Darwano, Hicham; Duy, Sung Vo; Sauvé, Sébastien


    We developed a protocol to quantify 12 emerging contaminants (ECs) (pharmaceuticals and hormones) and pesticides extracted from suspended particulate matter (SPM) of river water and municipal wastewaters samples as well as river sediments. The separation of suspended solids was realized using filtration of water samples. We tested a series of six different filter types. The effect of filtration on the concentrations of dissolved contaminants was evaluated to minimize losses of target compounds. The river sediment samples were lyophilized, and both SPM and sediment samples were subjected to ultrasonic extraction combined with C18 cartridge clean-up. Quantifications were realized using mass spectrometry. The method recoveries of all compounds ranged from 38 to 112 % in all studied matrices; poorer recoveries were achieved for sulfamethoxazole and diclofenac (as low as 38 %), whereas the recoveries for all other compounds in the wastewater treatment plant (WWTP) samples were between 68 and 111 %. The detection limits in sediments and SPM from river samples for the 12 analytes varied from 0.7 to 9.4 ng g(-1) and from 21 to 92 ng g(-1) for WWTP SPM samples. All targeted ECs were detected with concentrations ranging from 3 to 5,440 ng g(-1) in the studied matrices with the highest concentrations observed in WWTP SPM samples. A significant portion of the contaminants in a water sample is clearly associated with the suspended particulates. Optimization of water-treatment processes and environmental fate must absolutely consider the fraction of contaminants that is particulate-bound if one hopes to have a reasonable mass balance.

  5. Pulse Jet Mixing Tests With Noncohesive Solids

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Perry A.; Bamberger, Judith A.; Enderlin, Carl W.; Fort, James A.; Wells, Beric E.; Sundaram, S. K.; Scott, Paul A.; Minette, Michael J.; Smith, Gary L.; Burns, Carolyn A.; Greenwood, Margaret S.; Morgen, Gerald P.; Baer, Ellen BK; Snyder, Sandra F.; White, Michael K.; Piepel, Gregory F.; Amidan, Brett G.; Heredia-Langner, Alejandro


    This report summarizes results from pulse jet mixing (PJM) tests with noncohesive solids in Newtonian liquid. The tests were conducted during FY 2007 and 2008 to support the design of mixing systems for the Hanford Waste Treatment and Immobilization Plant (WTP). Tests were conducted at three geometric scales using noncohesive simulants, and the test data were used to develop models predicting two measures of mixing performance for full-scale WTP vessels. The models predict the cloud height (the height to which solids will be lifted by the PJM action) and the critical suspension velocity (the minimum velocity needed to ensure all solids are suspended off the floor, though not fully mixed). From the cloud height, the concentration of solids at the pump inlet can be estimated. The predicted critical suspension velocity for lifting all solids is not precisely the same as the mixing requirement for 'disturbing' a sufficient volume of solids, but the values will be similar and closely related. These predictive models were successfully benchmarked against larger scale tests and compared well with results from computational fluid dynamics simulations. The application of the models to assess mixing in WTP vessels is illustrated in examples for 13 distinct designs and selected operational conditions. The values selected for these examples are not final; thus, the estimates of performance should not be interpreted as final conclusions of design adequacy or inadequacy. However, this work does reveal that several vessels may require adjustments to design, operating features, or waste feed properties to ensure confidence in operation. The models described in this report will prove to be valuable engineering tools to evaluate options as designs are finalized for the WTP. Revision 1 refines data sets used for model development and summarizes models developed since the completion of Revision 0.

  6. Oscillation of a diamagnetic liquid bubble suspended by magnetic force

    Energy Technology Data Exchange (ETDEWEB)

    Yamane, R. E-mail:; Tomita, S.; Mai, J.; Park, M.K.; Oshima, S


    The levitation of the diamagnetic liquid droplet with the strong magnetic field is experimentally simulated, using the magnetic fluid as the surrounding fluid in place of air or gas, and the water bubble is levitated with the conventional permanent magnet. When the stepwise magnetic field is superposed, the suspended bubble behaves as a typical step response with the overshoot and viscous damping. The effects of the volume of the bubble, the strength of the magnetic field and the concentration of the magnetic fluid are investigated.

  7. Pulse Jet Mixing Tests With Noncohesive Solids

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Perry A.; Bamberger, Judith A.; Enderlin, Carl W.; Fort, James A.; Wells, Beric E.; Sundaram, S. K.; Scott, Paul A.; Minette, Michael J.; Smith, Gary L.; Burns, Carolyn A.; Greenwood, Margaret S.; Morgen, Gerald P.; Baer, Ellen BK; Snyder, Sandra F.; White, Michael; Piepel, Gregory F.; Amidan, Brett G.; Heredia-Langner, Alejandro; Bailey, Sharon A.; Bower, John C.; Denslow, Kayte M.; Eakin, David E.; Elmore, Monte R.; Gauglitz, Phillip A.; Guzman, Anthony D.; Hatchell, Brian K.; Hopkins, Derek F.; Hurley, David E.; Johnson, Michael D.; Kirihara, Leslie J.; Lawler, Bruce D.; Loveland, Jesse S.; Mullen, O Dennis; Pekour, Mikhail S.; Peters, Timothy J.; Robinson, Peter J.; Russcher, Michael S.; Sande, Susan; Santoso, Christian; Shoemaker, Steven V.; Silva, Steve M.; Smith, Devin E.; Su, Yin-Fong; Toth, James J.; Wiberg, John D.; Yu, Xiao-Ying; Zuljevic, Nino


    This report summarizes results from pulse jet mixing (PJM) tests with noncohesive solids in Newtonian liquid conducted during FY 2007 and 2008 to support the design of mixing systems for the Hanford Waste Treatment and Immobilization Plant (WTP). Tests were conducted at three geometric scales using noncohesive simulants. The test data were used to independently develop mixing models that can be used to predict full-scale WTP vessel performance and to rate current WTP mixing system designs against two specific performance requirements. One requirement is to ensure that all solids have been disturbed during the mixing action, which is important to release gas from the solids. The second requirement is to maintain a suspended solids concentration below 20 weight percent at the pump inlet. The models predict the height to which solids will be lifted by the PJM action, and the minimum velocity needed to ensure all solids have been lifted from the floor. From the cloud height estimate we can calculate the concentration of solids at the pump inlet. The velocity needed to lift the solids is slightly more demanding than "disturbing" the solids, and is used as a surrogate for this metric. We applied the models to assess WTP mixing vessel performance with respect to the two perform¬ance requirements. Each mixing vessel was evaluated against these two criteria for two defined waste conditions. One of the wastes was defined by design limits and one was derived from Hanford waste characterization reports. The assessment predicts that three vessel types will satisfy the design criteria for all conditions evaluated. Seven vessel types will not satisfy the performance criteria used for any of the conditions evaluated. The remaining three vessel types provide varying assessments when the different particle characteristics are evaluated. The assessment predicts that three vessel types will satisfy the design criteria for all conditions evaluated. Seven vessel types will not satisfy

  8. IUTAM symposium on hydrodynamic diffusion of suspended particles

    Energy Technology Data Exchange (ETDEWEB)

    Davis, R.H. [ed.


    Hydrodynamic diffusion refers to the fluctuating motion of nonBrownian particles (or droplets or bubbles) which occurs in a dispersion due to multiparticle interactions. For example, in a concentrated sheared suspension, particles do not move along streamlines but instead exhibit fluctuating motions as they tumble around each other. This leads to a net migration of particles down gradients in particle concentration and in shear rate, due to the higher frequency of encounters of a test particle with other particles on the side of the test particle which has higher concentration or shear rate. As another example, suspended particles subject to sedimentation, centrifugation, or fluidization, do not generally move relative to the fluid with a constant velocity, but instead experience diffusion-like fluctuations in velocity due to interactions with neighboring particles and the resulting variation in the microstructure or configuration of the suspended particles. In flowing granular materials, the particles interact through direct collisions or contacts (rather than through the surrounding fluid); these collisions also cause the particles to undergo fluctuating motions characteristic of diffusion processes. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

  9. Self-suspended permanent magnetic FePt ferrofluids

    KAUST Repository

    Dallas, Panagiotis


    We present the synthesis and characterization of a new class of self-suspended ferrofluids that exhibit remanent magnetization at room temperature. Our system relies on the chemisorption of a thiol-terminated ionic liquid with very low melting point on the surface of L10 FePt nanoparticles. In contrast, all types of ferrofluids previously reported employ either volatile solvents as the suspending media or superparamagnetic iron oxide nanoparticles (that lacks permanent magnetization) as the inorganic component. The ferrofluids do not show any sign of flocculation or phase separation, despite the strong interactions between the magnetic nanoparticles due to the strong chemisorption of the ionic liquid as evidenced by Raman spectroscopy and thermal analysis. Composites with high FePt loading (40 and 70. wt%) exhibit a pseudo solid-like rheological behavior and high remanent magnetization values (10.1 and 12.8. emu/g respectively). At lower FePt loading (12. wt%) a liquid like behavior is observed and the remanent and saturation magnetization values are 3.5 and 6.2. emu/g, respectively. The magnetic and flow properties of the materials can be easily fine tuned by controlling the type and amount of FePt nanoparticles used. © 2013 Elsevier Inc.

  10. Turbulence control of suspended matter aggregate size (United States)

    Jago, C. F.; Jones, S. E.; Rippeth, T. P.; Simpson, J. H.


    The size and properties of the aggregates which comprise suspended particulate matter (SPM) change on short time and length scales in shelf seas. There is experimental and theoretical evidence to suggest that turbulence plays a key role in aggregation but there is contradictory evidence with respect to disaggregation: it has been proposed that sinking stresses, rather than turbulent stresses, are the dominant control of disaggregation. But there is little observational evidence for turbulence control of particle properties. New observations are presented which provide compelling evidence for turbulence control of both aggregation and disaggregation. TKE dissipation and particle size were measured in situ at stratified sites in the northern North Sea in 110 m water depth during the period of weakening of the seasonal thermocline (in October/November) and in the Clyde Sea in 55 m water depth (April). There were similar vertical distributions of TKE dissipation E, SPM concentration C, and particle size D at both sites. At the base of the thermocline, there were minima in E and C, but a maximum in D, indicating that enhanced aggregation was occurring in this region of low turbulent stress. In the bottom mixed layer, E and C increased, while D decreased due to disaggregation in this region of increasing turbulent stress towards the seabed. Particles settling out of the low stress region at the base of the thermocline began to disaggregate when E increased to 3.2x10-6 watts m-2. D did not correlate directly with E because aggregation is a function of collision frequency (and hence of both C and E): this can be accounted for using a simplified theoretical aggregation model which treats flocs as self-similar fractal entities and allows simultaneous floc formation and break up, specified as functions of C and E. It was found that in the northern North Sea the measured D represents an equilibrium size predicted by the model, while in the Clyde Sea tidal variation in both C

  11. Contaminant Concentrations in Storm Water Entering the Sinclair/Dyes Inlet Subasin of the Puget Sound, USA During Storm Event and Baseflow Conditions (United States)


    total suspended solids (TSS); total organic carbon (TOC); total inorganic nitrogen (TIN); total Kjeldahl nitrogen (TKN); total phosphorus (TP); total...were determined for representative marine stations, streams, and storm water outfalls (Figure 1) during summer dry season baseflow (DSBF: May thru...October) and winter wet season baseflow (WSBF: November thru April) in 2001 and WSBF in 2005. DSBF contaminant concentrations were determined as the

  12. Suspended-sediment rating curve response to urbanization and wildfire, Santa Ana River, California (United States)

    Warrick, J.A.; Rubin, D.M.


    River suspended-sediment concentrations provide insights to the erosion and transport of materials from a landscape, and changes in concentrations with time may result from landscape processes or human disturbance. Here we show that suspended-sediment concentrations in the Santa Ana River, California, decreased 20-fold with respect to discharge during a 34-year period (1968−2001). These decreases cannot be attributed to changes in sampling technique or timing, nor to event or seasonal hysteresis. Annual peak and total discharge, however, reveal sixfold increases over the 34-year record, which largely explain the decreases in sediment concentration by a nonlinear dilution process. The hydrological changes were related to the widespread urbanization of the watershed, which resulted in increases in storm water discharge without detectable alteration of sediment discharge, thus reducing suspended-sediment concentrations. Periodic upland wildfire significantly increased water discharge, sediment discharge, and suspended-sediment concentrations and thus further altered the rating curve with time. Our results suggest that previous inventories of southern California sediment flux, which assume time-constant rating curves and extend these curves beyond the sampling history, may have substantially overestimated loads during the most recent decades.

  13. Transport of phosphorus, wash load and suspended sediment in the River Varde A in southwest Jutland, Denmark

    DEFF Research Database (Denmark)

    Thodsen, Hans; Hasholt, Bent; Pejrup, Morten


    Total phosphorus (TP) concentrations, suspended sediment concentrations (SSC) and wash load have been measured at three river monitoring stations in the River Varde Angstrom system since 1998. This provides the possibility of studying the link between SSC and wash load and concentrations of TP....... Transport rates of TP, suspended sediment and wash load at the three stations, calculated using rating curves, indicate the dependence of TP transport on the transport of suspended sediment and wash load. Two stations are located on tributaries flowing upstream of the third station located at a weir...... at the end of a small impoundment. Transport rates at the upstream stations were 57% higher for suspended sediment and 27% higher for wash load than at the downstream station, while transport of TP was the same. This indicates that phosphorus is transported adhered to the finest grain size fractions that do...

  14. Progress towards Acoustic Suspended Sediment Transport Monitoring: Fraser River, BC (United States)

    Attard, M. E.; Venditti, J. G.; Church, M. A.; Kostaschuk, R. A.


    Our ability to predict the timing and quantity of suspended sediment transport is limited because fine sand, silt and clay delivery are supply limited, requiring empirical modeling approaches of limited temporal stability. A solution is the development of continuous monitoring techniques capable of tracking sediment concentrations and grain-size. Here we examine sediment delivery from upstream sources to the lower Fraser River. The sediment budget of the lower Fraser River provides a long-term perspective of the net changes in the channels and in sediment delivery to Fraser Delta. The budget is based on historical sediment rating curves developed from data collected from 1965-1986 by the Water Survey of Canada. We explore the possibility of re-establishing the sediment-monitoring program using hydro-acoustics by evaluating the use of a 300 kHz side-looking acoustic Doppler current profiler (aDcp), mounted just downstream of the sand-gravel transition at Mission, for continuous measurement of suspended sediment transport. Complementary field observations include conventional bottle sampling with a P-63 sampler, vertical profiles with a downward-looking 600 kHz aDcp, and 1200 kHz aDcp discharge measurements. We have successfully completed calibration of the downward-looking aDcp with the P-63 samples; the side-looking aDcp signals remain under investigation. A comparison of several methods for obtaining total sediment flux indicates that suspended sediment concentration (SSC) closely follows discharge through the freshet and peaks in total SSC and sand SSC coincide with peak measurements of discharge. Low flows are dominated by fine sediment and grain size increases with higher flows. This research assesses several techniques for obtaining sediment flux and contributes to the understanding of sediment delivery to sand-bedded portions of the river.

  15. Local Algorithm for Monitoring Total Suspended Sediments in Micro-Watersheds Usin Drones and Remote Sensing Applications. Case Study: TEUSACÁ River, la Calera, Colombia (United States)

    Sáenz, N. A.; Paez, D. E.; Arango, C.


    An empirical relationship of Total Suspended Sediments (TSS) concentrations and reflectance values obtained with Drones' aerial photos and processed using remote sensing tools was set up as the main objective of this research. A local mathematic algorithm for the micro-watershed of the Teusacá River at La Calera, Colombia, was developed based on the computing of four component of bands from consumed-grade cameras obtaining from each their corresponding reflectance values from procedures for correcting digital camera imagery and using statistical analysis for study the fit and RMSE of 25 regressions. The assessment was characterized by the comparison of reflectance values and 34 in-situ data measurements concentrations between 1.6 and 33 mg L-1 taken from the superficial layer of the river in two campaigns. A large data set of empirical and referenced algorithm from literature were used to evaluate the accuracy and precision of the relationship. For estimation of TSS, a higher accuracy was achieved using the Tassan's algorithm with the BAND X/ BANDX ratio. The correlation coefficient with R2 = X demonstrate the feasibility of use remote sensed data with consumed-grade cameras as an effective tool for a frequent monitoring and controlling of water quality parameters such as Total Suspended Solids of watersheds, these being the most vulnerable and less compliance with environmental regulations.


    Directory of Open Access Journals (Sweden)

    N. A. Sáenz


    Full Text Available An empirical relationship of Total Suspended Sediments (TSS concentrations and reflectance values obtained with Drones’ aerial photos and processed using remote sensing tools was set up as the main objective of this research. A local mathematic algorithm for the micro-watershed of the Teusacá River at La Calera, Colombia, was developed based on the computing of four component of bands from consumed-grade cameras obtaining from each their corresponding reflectance values from procedures for correcting digital camera imagery and using statistical analysis for study the fit and RMSE of 25 regressions. The assessment was characterized by the comparison of reflectance values and 34 in-situ data measurements concentrations between 1.6 and 33 mg L−1 taken from the superficial layer of the river in two campaigns. A large data set of empirical and referenced algorithm from literature were used to evaluate the accuracy and precision of the relationship. For estimation of TSS, a higher accuracy was achieved using the Tassan’s algorithm with the BAND X/ BANDX ratio. The correlation coefficient with R2 = X demonstrate the feasibility of use remote sensed data with consumed-grade cameras as an effective tool for a frequent monitoring and controlling of water quality parameters such as Total Suspended Solids of watersheds, these being the most vulnerable and less compliance with environmental regulations.

  17. Medición de la concentración de sedimentos en suspensión mediante dispositivos ópticos y acústicos: aplicación en sistemas tropicales (Delta del río Mira, Colombia Measurement of suspended sediment concentration using optical and acoustic devices: application in tropical systems (Mira River Delta, Colombia

    Directory of Open Access Journals (Sweden)

    Juan Camilo Restrepo


    Full Text Available En los últimos años, la utilización de dispositivos ópticos (e.g. Optical Backscatter Sensor, OBS y acústicos (e.g. Acoustic Doppler Current Profiler-ADCP ha permitido monitorear con mayor resolución la variabilidad temporal y espacial de la concentración de sedimentos en suspensión (CSS en ambientes costeros y estuarinos. Sin embargo, la aplicación de estas técnicas en ambientes tropicales ha tenido un desarrollo incipiente. En el presente trabajo se implementó un procedimiento de calibración para un dispositivo OBS-3A, tomando como patrón de calibración sedimento seco y desagregado de la zona de estudio. Además, se presentan las correcciones a las que se debe someter la señal de respuesta del ADCP, debido a la dispersión geométrica, la atenuación del sonido por el agua y las partículas en suspensión, para que sea útil en la estimación de CSS. El ADCP y el OBS-3A se utilizaron para realizar mediciones de CSS en el sistema deltaico del río Mira (isla del Morro y desembocadura principal, ubicado sobre la costa del Pacífico colombiano, un ambiente costero tropical donde algunos factores oceanográficos y estuarinos son determinantes en la señal de respuesta de los equipos.In recent years, the use of optical (Optical Backscatter Sensor, OBS and acoustic (Acoustic Current Doppler Profiler, ADCP instruments has allowed monitoring the temporal and spatial variation of the suspended sediment concentration (SSC in coastal and estuarine environments with greater resolution. However, the development of the application of those techniques in tropical environments is incipient. For this study, an OBS-3A calibration procedure was implemented, taking dry and desegregated sediment from the study zone as a calibrating pattern. Moreover, we present the corrections required for the ADCP signal to be useful in the estimation of SSC due to geometrical spreading, the attenuation of sound by water, and the particles in suspension. The ADCP

  18. Methods for evaluating temporal groundwater quality data and results of decadal-scale changes in chloride, dissolved solids, and nitrate concentrations in groundwater in the United States, 1988-2010 (United States)

    Lindsey, Bruce D.; Rupert, Michael G.


    Decadal-scale changes in groundwater quality were evaluated by the U.S. Geological Survey National Water-Quality Assessment (NAWQA) Program. Samples of groundwater collected from wells during 1988-2000 - a first sampling event representing the decade ending the 20th century - were compared on a pair-wise basis to samples from the same wells collected during 2001-2010 - a second sampling event representing the decade beginning the 21st century. The data set consists of samples from 1,236 wells in 56 well networks, representing major aquifers and urban and agricultural land-use areas, with analytical results for chloride, dissolved solids, and nitrate. Statistical analysis was done on a network basis rather than by individual wells. Although spanning slightly more or less than a 10-year period, the two-sample comparison between the first and second sampling events is referred to as an analysis of decadal-scale change based on a step-trend analysis. The 22 principal aquifers represented by these 56 networks account for nearly 80 percent of the estimated withdrawals of groundwater used for drinking-water supply in the Nation. Well networks where decadal-scale changes in concentrations were statistically significant were identified using the Wilcoxon-Pratt signed-rank test. For the statistical analysis of chloride, dissolved solids, and nitrate concentrations at the network level, more than half revealed no statistically significant change over the decadal period. However, for networks that had statistically significant changes, increased concentrations outnumbered decreased concentrations by a large margin. Statistically significant increases of chloride concentrations were identified for 43 percent of 56 networks. Dissolved solids concentrations increased significantly in 41 percent of the 54 networks with dissolved solids data, and nitrate concentrations increased significantly in 23 percent of 56 networks. At least one of the three - chloride, dissolved solids, or

  19. Mutual relationships of suspended sediment, turbidity and visual clarity in New Zealand rivers

    Directory of Open Access Journals (Sweden)

    D. J. Ballantine


    Full Text Available Many river water quality monitoring programmes do not measure suspended particulate matter (SPM mass concentrations despite significant interest in its multiple effects on aquatic ecosystems. Regular monthly sampling usually intercepts rivers in baseflow when suspended sediment mass concentrations and fluxes are relatively low and not of particular interest. New Zealand’s National Rivers Water Quality Network (NRWQN is probably typical in not measuring SPM mass, although visual clarity and nephelometric turbidity are routinely measured. In order to better characterize SPM in NZ rivers, total suspended sediment (TSS was temporarily added to the NRWQN. Turbidity, visual clarity and TSS are mutually inter-related over all 77 sites, although with considerable data scatter. However, within individual rivers turbidity and visual clarity are typically fairly closely related to TSS and provide fair to excellent surrogates. Therefore, TSS need not be measured routinely because it can be estimated with sufficient precision for many purposes from visibility or turbidity.

  20. Recent Trends in Suspended Sediment Load & Water Quality in the Upper Chesapeake Bay (United States)

    Freeman, L. A.; Ackleson, S. G.


    The Chesapeake Bay spans several major cities on the US east coast and drains a large watershed (164,200 km2) to the Atlantic Ocean. Upstream deforestation and agriculture have led to a major decline in water quality (increased sediment and nutrient load) of the Bay over the past century. Sediment flux into the Chesapeake Bay is a natural process, but has become an environmental concern as land use changes have exacerbated natural suspended sediment loads and saturated the capacity of the estuary to filter and remove sediments. In situ measurements of suspended sediments and surface reflectance from the Potomac, Patapsco, and Severn River were used to develop algorithms that convert surface reflectance from Landsat (1-3, 4-5, 7, 8) imagery to suspended sediment concentration for the entire Chesapeake Bay. A unique time series of suspended sediment load in the Chesapeake Bay was compiled from Landsat imagery dating from 1977-2015. Particular focus is given to the upper Chesapeake Bay near Washington, DC and Baltimore, MD to understand urban effects. In particular, the Potomac, Patapsco, and Severn River are examined from both remote sensing and in situ measurements. Landsat imagery combined with in situ monitoring provides environmental scientists and resource managers with detailed trends in sediment distribution and concentration, a key measure of water quality. Trends of suspended sediment load in several rivers and the upper Chesapeake Bay will be presented, along with a discussion of suspended sediment algorithms for Landsat imagery. Advantages of Landsat 8 (improved signal-to-noise performance and more bands) versus previous sensors will be examined for suspended sediment applications.

  1. 9 CFR 201.81 - Suspended registrants. (United States)


    ... 201.81 Animals and Animal Products GRAIN INSPECTION, PACKERS AND STOCKYARDS ADMINISTRATION (PACKERS AND STOCKYARDS PROGRAMS), DEPARTMENT OF AGRICULTURE REGULATIONS UNDER THE PACKERS AND STOCKYARDS ACT Services § 201.81 Suspended registrants. No stockyard owner, packer, market agency, or dealer shall employ...

  2. Electrodialytic remediation of suspended mine tailings

    DEFF Research Database (Denmark)

    Hansen, Henrik K.; Rojo, Adrian; Pino, Denisse


    experiment at 40 mA, with approximately 137.5 g mine tailings on dry basis. The removal for a static (baseline) experiment only amounted 15% when passing approximately the same amount of charge through 130 g of mine tailings. The use of air bubbling to keep the tailings suspended increased the removal...

  3. Environmental toxicology: Acute effects of suspended particulate ...

    African Journals Online (AJOL)

    ... from the control values were found significant at 99% confidence level. Possible inhalatory problems are thus anticipated from prolonged accumulation of the dust in the respiratory system. KEY WORDS: Environmental toxicology, Suspended particulate matter, Dust analysis, Hematological indices, Wister albino rats. Bull.

  4. Environmental toxicology: Acute effects of suspended particulate ...

    African Journals Online (AJOL)

    The elemental contents of suspended particulate matter (dust) samples from Maiduguri, Nigeria, were determined which showed appreciably high levels for especially Pb, Fe, Cu, Zn, K, Ca, and. Na. Wister albino rats were exposed to graded doses of phosphate buffered saline carried dust particles. The hematological ...

  5. The Shape of Breasts Suspended in Liquid

    NARCIS (Netherlands)

    De Kleijn, S.C.; Rensen, W.H.J.


    Philips has designed an optical mammography machine. In this machine the breast is suspended into a cup in which the measurements take place. A special fluid is inserted into the cup to prevent the light from going around the breast instead of going through it but this fluid also weakens the signal.

  6. Flow Laminarization and Acceleration by Suspended Particles

    NARCIS (Netherlands)

    Bertsch, M.; Hulshof, J.; Prostokishin, V.M.


    In [Comm. Appl. Math. Comput. Sci., 4(2009), pp. 153-175], Barenblatt presents a model for partial laminarization and acceleration of shear flows by the presence of suspended particles of different sizes, and provides a formal asymptotic analysis of the resulting velocity equation. In the present

  7. Emulsifying and Suspending Properties of Enterolobium ...

    African Journals Online (AJOL)

    Background:The thermodynamic instability of emulsions and suspensions necessitate the incorporation of emulsifiers and suspending agents respectively, in order to stabilize the formulations and ensure administration of accurate doses. Objective:Enterolobium cyclocarpum gum was characterized and evaluated for its ...

  8. Altered translatability of messenger RNA from suspended anchorage-dependent fibroblasts: reversal upon cell attachment to a surface. (United States)

    Farmer, S R; Ben-Ze'av, A; Benecke, B J; Penman, S


    Anchorage-dependent cells, when forced into suspension culture, display a repertoire of dramatic, coordinated regulatory phenomena. Message production promptly decreases 5 gold but the cells maintain a constant amount of poly(A)+ by means of a concomitant stabilization of mRNA against decay. Protein synthesis shuts down much later and the mRNA is stored in a nonfunctioning state. In this study, the inactive mRNA is extracted from suspended cells and shown to have aberrant translation properties. Well defined polypeptides are apparently no longer synthesized when this mRNA directs protein formation in either reticulocyte or wheat germ-derived heterologous translation systems. Rather, shortened peptides are formed by this mRNA and these become smaller as mRNA is used from cells suspended for longer periods of time. Very few focused spots are formed when the aberrant polypeptides are analyzed in two-dimensional electrophoresis. The sedimentation properties of suspended cell mRNA and the size of poly(A) are unchanged from control monolayer cells. Cross-hybridization of cDNA transcribed from a control cell message population with suspended cell mRNA shows that all sequences are present in normal concentrations. While most identifiable spots disappear from the two-dimensional gel electropherograms of the protein products produced by suspended cell mRNA, a few polypeptides are still synthesized in relatively normal amounts. Conserved polypeptides are found in products of both the reticulocyte and wheat germ systems, but they are different products in each case. The lesion in the suspended cell mRNA does not seem to be at the 5' termini, since synthesis of the shortened peptides is fully sensitive to inhibition of pm7G. Cells that contain extensively modified message can resume protein synthesis when allowed to reattach to a solid substrate. There is an apparent remodification of mRNA to normal translatability within a few hours of cell reattachment, since mRNA from

  9. Element geochemical analysis of the contribution of aeolian sand to suspended sediment in desert stream flash floods. (United States)

    Jia, Xiaopeng; Wang, Haibing


    The interaction of wind and water in semiarid and arid areas usually leads to low-frequency flash flood events in desert rivers, which have adverse effects on river systems and ecology. In arid zones, many aeolian dune-fields terminate in stream channels and deliver aeolian sand to the channels. Although aeolian processes are common to many desert rivers, whether the aeolian processes contribute to fluvial sediment loss is still unknown. Here, we identified the aeolian-fluvial cycling process responsible for the high rate of suspended sediment transport in the Sudalaer desert stream in the Ordos plateau of China. On the basis of element geochemistry data analysis, we found that aeolian sand was similar to suspended sediment in element composition, which suggests that aeolian sand contributes to suspended sediment in flash floods. Scatter plots of some elements further confirm that aeolian sand is the major source of the suspended sediment. Factor analysis and the relation between some elements and suspended sediment concentration prove that the greater the aeolian process, the higher the suspended sediment concentration and the greater the contribution of aeolian sand to suspended sediment yield. We conclude that aeolian sand is the greatest contributor to flash floods in the Sudalaer desert stream.

  10. Element Geochemical Analysis of the Contribution of Aeolian Sand to Suspended Sediment in Desert Stream Flash Floods

    Directory of Open Access Journals (Sweden)

    Xiaopeng Jia


    Full Text Available The interaction of wind and water in semiarid and arid areas usually leads to low-frequency flash flood events in desert rivers, which have adverse effects on river systems and ecology. In arid zones, many aeolian dune-fields terminate in stream channels and deliver aeolian sand to the channels. Although aeolian processes are common to many desert rivers, whether the aeolian processes contribute to fluvial sediment loss is still unknown. Here, we identified the aeolian-fluvial cycling process responsible for the high rate of suspended sediment transport in the Sudalaer desert stream in the Ordos plateau of China. On the basis of element geochemistry data analysis, we found that aeolian sand was similar to suspended sediment in element composition, which suggests that aeolian sand contributes to suspended sediment in flash floods. Scatter plots of some elements further confirm that aeolian sand is the major source of the suspended sediment. Factor analysis and the relation between some elements and suspended sediment concentration prove that the greater the aeolian process, the higher the suspended sediment concentration and the greater the contribution of aeolian sand to suspended sediment yield. We conclude that aeolian sand is the greatest contributor to flash floods in the Sudalaer desert stream.

  11. Consequences of hydrological events on the delivery of suspended sediment and associated radionuclides from the Rhone River to the Mediterranean Sea

    Energy Technology Data Exchange (ETDEWEB)

    Eyrolle, Frederique; Antonelli, Christelle; Ferrand, Emmanuelle [IRSN, Saint Paul Lez Durance (France). Pole Radioprotection environnement, dechets et crise, PRP-ENV, Service d' Etude et de Surveillance de la Radioactivite dans l' Environnement; Raimbault, Patrick [Institut Mediterraneen d' Oceanologie, OSU Pytheas, Marseille (France); Aubert, Dominique [CEFREM, Univ. de Perpignan Via Domitia CNRS UMR, Perpignan (France); Jacquet, Stephanie; Radakovitch, Olivier; Raccasi, Guillaume [Aix-Marseille Univ.-CNR-IRD-College de France, Aix en Provence (France); Charmasson, Sabine [IRSN, La Seyne sur mer (France). Pole Radioprotection, environnement, dechets et crise, PRP-ENV, Service d' Etude et de Surveillance de la Radioactivite dans l' Environnement; Gurriaran, Rodolfo [IRSN, Orsay (France). Pole Radioprotection, environnement, dechets et crise, PRP-ENV, Service de Traitement des echantillos et de Metrologie pour l' Environnement


    level and fate of suspended solids and radionuclide concentrations during flood events occurring in a large river system that could be contaminated by chronic or accidental radioactive releases. These results are of fundamental importance for further interpretations of sediment dynamics at the river mouth.

  12. Observations of suspended sediment from ADCP and OBS measurements in a mud-dominated environment

    NARCIS (Netherlands)

    Hoitink, A.J.F.; Hoekstra, P.


    The ability of a 1.2-MHz Acoustic Doppler Current Profiler (ADCP) to measure suspended sediment concentration (SSC) and particle size variation in a mud-dominated environment has been investigated. Experiments were conducted in the Bay of Banten, Indonesia, where clays and silts in the range of 3-55

  13. Energy content of suspended detritus from Arabian Sea

    Digital Repository Service at National Institute of Oceanography (India)

    Krishnakumari, L.; Sumitra-Vijayaraghavan; Royan, J.P.

    Energy components of suspended matter included phytoplankton, zooplankton and detritus inclusive of microorganisms adsorbed to detritus. Of these, detritus contributed most of the energy (98%). The average caloric content of suspended detritus...

  14. The suspended sentence in French Criminal Law

    Directory of Open Access Journals (Sweden)

    Jovašević Dragan


    Full Text Available From the ancient times until today, criminal law has provided different criminal sanctions as measures of social control. These coercive measures are imposed on the criminal offender by the competent court and aimed at limitting the offender's rights and freedoms or depriving the offender of certain rights and freedoms. These sanctions are applied to the natural or legal persons who violate the norms of the legal order and injure or endanger other legal goods that enjoy legal protection. In order to effectively protect social values, criminal legislations in all countries predict a number of criminal sanctions. These are: 1 imprisonment, 2 precautions, 3 safety measures, 4 penalties for juveniles, and 5 sanctions for legal persons. Apart and instead of punishment, warning measures have a significant role in the jurisprudence. Since they emerged in the early 20th century in the system of criminal sanctions, there has been an increase in their application to criminal offenders, especially when it comes to first-time offenders who committed a negligent or accidental criminal act. Warnings are applied in case of crimes that do not have serious consequences, and whose perpetrators are not hardened and incorrigible criminals. All contemporary criminal legislations (including the French legilation provide a warning measure of suspended sentence. Suspended sentence is a conditional stay of execution of sentence of imprisonment for a specified time, provided that the convicted person does not commit another criminal offense and fulfills other obligations. This sanction applies if the following two conditions are fulfilled: a forma! -which is attached to the sentence of imprisonment; and b material -which is the court assessment that the application of this sanction is justified and necessary in a particular case. In many modern criminal legislations, there are two different types of suspended (conditional sentence: 1 ordinary (classical suspended

  15. Suspended sediment and turbidity after road construction/improvement and forest harvest in streams of the Trask River Watershed Study, Oregon (United States)

    Ivan Arismendi; Jeremiah D. Groom; Maryanne Reiter; Sherri L. Johnson; Liz Dent; Mark Meleason; Alba Argerich; Arne E. Skaugset


    Transport of fine-grained sediment from unpaved forest roads into streams is a concern due to the potential negative effects of additional suspended sediment on aquatic ecosystems. Here we compared turbidity and suspended sediment concentration (SSC) dynamics in five nonfish bearing coastal Oregon streams above and below road crossings, during three consecutive time...

  16. Assessment of suspended particulate matters and their heavy metal content in the ambient air of Mobarakeh city, Isfahan, Iran


    Avazali Saririan Mobarakeh; Bibi Fatemeh Nabavi; Mahnaz Nikaeen; Mohammad Mehdi Amin; Akbar Hassanzadeh; Kazem Nadafi


    Aim: This study was carried out to investigate the quality of Mobarakeh ambient air in terms of suspended particles and heavy metals. Material and Methods: The current study was carried out in Mobarakeh city, Isfahan, Iran. Air sampling was performed in three sites for a 1-year period (in 2007). Measurement of total suspended particles (TSP) and heavy metals was achieved using high volume air sampler with fiberglass filter. The concentration of heavy metals, including Pb, Ni, Zn, Fe, and ...

  17. Temporal variability of suspended sediment sources in an alpine catchment combining river/rainfall monitoring and sediment fingerprinting


    Navratil, O.; Evrard, O.; Esteves, Michel; Legout, C.; Ayrault, S.; Nemery, J.; Mate-Marin, A.; Ahmadi, M.; Lefevre, I.; Poirel, A.; Bonte, P.


    Influence of the rainfall regime on erosion and transfer of suspended sediment in a 905-km(2) mountainous catchment of the southern French Alps was investigated by combining sediment monitoring, rainfall data, and sediment fingerprinting (based on geochemistry and radionuclide concentrations). Suspended sediment yields were monitored between October 2007 and December 2009 in four subcatchments (22-713km(2)). Automatic sediment sampling was triggered during floods to trace the sediment origin ...

  18. Growth and energetics in Spisula subtruncata (Da Costa) and the effect of suspended bottom material

    DEFF Research Database (Denmark)

    Møhlenberg, F.; Kiørboe, Thomas


    The influence of suspended bottom material (0-25 mg/l) and algal cells (Phaeodactylum tricornutum) (0-500 .mu.g dry org wt[organic weight]/l) on clearance, growth and energetics in S. subtruncata (da Costa) was studied. Clearance and respiration rate were independent of concentrations of algae...... bottom material on growth is due to a higher efficiency of assimilation of the ingested algae and/or the utilization of organic matter in the suspended bottom material. The efficiency of algal assimilation decreased from 76% at a low (150 .mu.g dry org wt/l) to 33% at a high (500 .mu.g) algal...

  19. Optomechanics for thermal characterization of suspended graphene (United States)

    Dolleman, Robin J.; Houri, Samer; Davidovikj, Dejan; Cartamil-Bueno, Santiago J.; Blanter, Yaroslav M.; van der Zant, Herre S. J.; Steeneken, Peter G.


    The thermal response of graphene is expected to be extremely fast due to its low heat capacity and high thermal conductivity. In this work, the thermal response of suspended single-layer graphene membranes is investigated by characterization of their mechanical motion in response to a high-frequency modulated laser. A characteristic delay time τ between the optical intensity and mechanical motion is observed, which is attributed to the time required to raise the temperature of the membrane. We find, however, that the measured time constants are significantly larger than the predicted ones based on values of the specific heat and thermal conductivity. In order to explain the discrepancy between measured and modeled τ , a model is proposed that takes a thermal boundary resistance at the edge of the graphene drum into account. The measurements provide a noninvasive way to characterize thermal properties of suspended atomically thin membranes, providing information that can be hard to obtain by other means.

  20. Skin permeation of lidocaine from crystal suspended oily formulations. (United States)

    Matsui, Rakan; Hasegawa, Masaaki; Ishida, Masami; Ebata, Toshiya; Namiki, Noriyuki; Sugibayashi, Kenji


    In vitro permeation of lidocaine (lidocaine base, LID) through excised rat skin was investigated using several LID-suspended oily formulations. The first skin permeation of LID from an LID-suspended oily solution such as liquid paraffin (LP), isopropyl myristate (IPM), polyoxyethylene (2) oleylether (BO-2), and diethyl sebacate (DES) was evaluated and compared with that from polyethylene glycol 400 (PEG400) solution, a hydrophilic base. The obtained permeation rate of LID, Japp, from PEG400, LP, IPM, BO-2, and DES was in the order of DES>BO-2=IPM>LP>PEG400, and increased with LID solubility in the oily solvents, although LID crystals were dispersed in all solvents. Subsequently, oily formulations that consisted of different ratios of the first oily solvent (IPM, BO-2, or DES) (each 0-20%), the second oily solvent (LP) and an oily mixture of microcrystalline wax/white petrolatum/paraffin (1/5/4) were evaluated. BO-2 groups at a concentration of 5% and 10% had the highest Japp among the oily formulations, although a higher BO-2 resulted in lower skin permeation. In addition, pretreatment with BO-2 increased the skin permeation of LID. These results suggest that the penetration enhancing effect by the system may be related to the skin penetration of BO-2 itself. Finally, mathematical analysis was done to evaluate the effect of BO-2, and it was shown that BO-2 improved the LID solubility in stratum corneum lipids to efficiently enhance the LID permeation through skin.

  1. The role of suspension events in cross-shore and longshore suspended sediment transport in the surf zone (United States)

    Jaffe, Bruce E.


    Suspension of sand in the surf zone is intermittent. Especially striking in a time series of concentration are periods of intense suspension, suspension events, when the water column suspended sediment concentration is an order of magnitude greater than the mean concentration. The prevalence, timing, and contribution of suspension events to cross-shore and longshore suspended sediment transport are explored using field data collected in the inner half of the surf zone during a large storm at Duck, NC. Suspension events are defined as periods when the concentration is above a threshold. Events tended to occur during onshore flow under the wave crest, resulting in an onshore contribution to the suspended sediment transport. Even though large events occurred less than 10 percent of the total time, at some locations onshore transport associated with suspension events was greater than mean-current driven offshore-directed transport during non-event periods, causing the net suspended sediment transport to be onshore. Events and fluctuations in longshore velocity were not correlated. However, events did increase the longshore suspended sediment transport by approximately the amount they increase the mean concentration, which can be up to 35%. Because of the lack of correlation, the longshore suspended sediment transport can be modeled without considering the details of the intensity and time of events as the vertical integration of the product of the time-averaged longshore velocity and an event-augmented time-averaged concentration. However, to accurately model cross-shore suspended sediment transport, the timing and intensity of suspension events must be reproduced.

  2. Flow modelling to estimate suspended sediment travel times for two Canadian Deltas

    Directory of Open Access Journals (Sweden)

    S. R. Fassnacht


    Full Text Available The approximate travel times for suspended sediment transport through two multi-channel networks are estimated using flow modelling. The focus is on the movement of high sediment concentrations that travel rapidly downstream. Since suspended sediment transport through river confluences and bifurcation movement is poorly understood, it is assumed that the sediment moves at approximately the average channel velocity during periods of high sediment load movement. Calibration of the flow model is discussed, with an emphasis on the incorporation of cross-section data, that are not referenced to a datum, using a continuous water surface profile. Various flow regimes are examined for the Mackenzie and the Slave River Deltas in the Northwest Territories, Canada, and a significant variation in travel times is illustrated. One set of continuous daily sediment measurements throughout the Mackenzie Delta is used to demonstrate that the travel time estimates are reasonable. Keywords: suspended sediment; multi-channel river systems; flow modelling; sediment transport

  3. Remoção de sólidos em suspensão na água residuária da despolpa de frutos do cafeeiro em filtros constituídos por pergaminho de grãos de café submetido a compressões Removal of suspended solids in the wastewater of the coffee shrub cherry pulping by filters constituted by parchment of the coffee beans subjected to compressions

    Directory of Open Access Journals (Sweden)

    Antonio T. de Matos


    Full Text Available A remoção de sólidos em suspensão é fundamental para que se possa aplicar a água residuária gerada na despolpa de frutos do cafeeiro (ARC na fertirrigação de culturas agrícolas. Dentre as opções disponíveis para efetuar a remoção de SS da ARC, está o uso de filtros orgânicos. Este trabalho foi desenvolvido com o objetivo de avaliar a influência do grau de compressão na redução do volume e na eficiência do pergaminho, utilizado como material filtrante, na remoção de sólidos em suspensão (SS na ARC. Numa primeira etapa, foram realizados ensaios nos quais corpos-de-prova de pergaminho triturado (retido entre as peneiras de 2,5 e 3 mm e não-triturado (na condição em que é produzido foram submetidos a diferentes compressões para a redução do volume das colunas filtrantes em 5; 10; 15; 20; 25 e 28%. Numa segunda etapa, os corpos-de-prova foram utilizados como material filtrante da ARC para a avaliação da sua capacidade de remoção de SS presentes nessa água residuária. O pergaminho triturado ofereceu maior resistência à compressão e proporcionou, para as mesmas reduções volumétricas no material filtrante, maior eficiência na remoção de SS da ARC do que o pergaminho não-triturado. Reduções na faixa de 10% a 15% no volume do filtro constituído por pergaminho triturado foram suficientes para obter satisfatórias eficiências na remoção de SS da ARC, enquanto, para filtros constituídos de pergaminho não-triturado, as reduções de volume devem ser superiores a 25%.The removal of suspended solids (SS is fundamental to apply the wastewater from the coffee shrub cherry pulping (ARC on agricultural crops fertigation. Among the available options for the removal of SS from ARC is the use of organic filters. This study was carried out to evaluate the influence of the compression degree on either volume reduction or parchment efficiency, when used as medium filter for the removal of suspended solids (SS in

  4. Quantification of caffeine in dietary supplements and energy drinks by solid-surface fluorescence using a pre-concentration step on multi-walled carbon nanotubes and Rhodamine B. (United States)

    Talio, María Carolina; Acosta, María Gimena; Alesso, Magdalena; Luconi, Marta O; Fernández, Liliana P


    A new method for the determination of caffeine, a non-fluorescent analyte, based on the enhancement of the fluorescence of Rhodamine B dye on a membrane filter modified with multi-walled carbon nanotubes is proposed. The method comprises pre-concentration of caffeine on a solid support by chemofiltration in buffered solution onto multi-walled carbon nanotubes previously oxidised and dispersed in cationic surfactant admicelles. The effect of experimental parameters, including the nature of the buffer and pH, the nature of the solid support, filtration flow rate, dye and carbon nanotube concentration, and the nature of the surfactant and concentration were investigated by means univariation assays. Under optimum experimental conditions, the pre-concentration system gave detection and quantification limits of 0.3 and 1.1 µg l(-1), respectively. A wide linear range was achieved varying from concentrations of 1.1 to 9.7 × 103 µg l(-1) (r(2) = 0.999). Satisfactory recovery values were obtained using the method of standard addition, confirming the feasibility of this method for caffeine determination in energising dietary supplements and energy drinks.

  5. Cumulative effects of suspended sediments, organic nutrients and temperature stress on early life history stages of the coral Acropora tenuis (United States)

    Humanes, Adriana; Ricardo, Gerard F.; Willis, Bette L.; Fabricius, Katharina E.; Negri, Andrew P.


    Coral reproduction is vulnerable to both declining water quality and warming temperatures, with simultaneous exposures likely compounding the negative impact of each stressor. We investigated how early life processes of the coral Acropora tenuis respond to increasing levels of suspended sediments in combination with temperature or organic nutrients. Fertilization success and embryo development were more sensitive to suspended sediments than to high temperatures or nutrient enrichment, while larval development (after acquisition of cilia) and settlement success were predominantly affected by thermal stress. Fertilization success was reduced 80% by suspended sediments, and up to 24% by temperature, while the addition of nutrients to suspended sediments had no further impact. Larval survivorship was unaffected by any of these treatments. However, settlement success of larvae developing from treatment-exposed embryos was negatively affected by all three stressors (e.g. up to 55% by suspended sediments), while exposure only during later larval stages predominantly responded to temperature stress. Environmentally relevant levels of suspended sediments and temperature had the greatest impacts, affecting more processes than the combined impacts of sediments and nutrients. These results suggest that management strategies to maintain suspended sediments at low concentrations during coral spawning events will benefit coral recruitment, especially with warming climate.

  6. Turbidity and suspended sediment in the upper Esopus Creek watershed, Ulster County, New York (United States)

    McHale, Michael R.; Siemion, Jason


    Suspended-sediment concentrations (SSCs) and turbidity were measured for 2 to 3 years at 14 monitoring sites throughout the upper Esopus Creek watershed in the Catskill Mountains of New York State. The upper Esopus Creek watershed is part of the New York City water-supply system that supplies water to more than 9 million people every day. Turbidity, caused primarily by high concentrations of inorganic suspended particles, is a potential water-quality concern because it colors the water and can reduce the effectiveness of drinking-water disinfection. The purposes of this study were to quantify concentrations of suspended sediment and turbidity levels, to estimate suspended-sediment loads within the upper Esopus Creek watershed, and to investigate the relations between SSC and turbidity. Samples were collected at four locations along the main channel of Esopus Creek and at all of the principal tributaries. Samples were collected monthly and during storms and were analyzed for SSC and turbidity in the laboratory. Turbidity was also measured every 15 minutes at six of the sampling stations with in situ turbidity probes.

  7. Effect of low oxygen concentrations on growth and alpha-amylase production of Aspergillus oryzae in model solid-state fermentation systems

    NARCIS (Netherlands)

    Rahardjo, Y.S.P.; Sie, S.; Weber, F.J.; Tramper, J.; Rinzema, A.


    Oxygen transfer in the fungal mat is a major concern in solid-state fermentation (SSF). Oxygen supply into the mycelial layers is hampered by diffusion limitation. For aerobic fungi, like Aspergillus oryzae, this oxygen depletion can be a severely limiting factor for growth and metabolite

  8. Development of All-Solid-State Sensors for Measurement of Nitric Oxide and Ammonia Concentrations by Optical Absorption in Particle-Laden Combustion Exhaust Streams

    Energy Technology Data Exchange (ETDEWEB)

    Jerald A. Caton; Kalyan Annamalai; Robert P. Lucht


    An all-solid-state continuous-wave (cw) laser system for ultraviolet absorption measurements of the nitric oxide (NO) molecule has been developed and demonstrated. For the NO sensor, 250 nW of tunable cw ultraviolet radiation is produced by sum-frequency-mixing of 532-nm radiation from a diode-pumped Nd:YAG laser and tunable 395-nm radiation from an external cavity diode laser (ECDL). The sum-frequency-mixing process occurs in a beta-barium borate crystal. The nitric oxide absorption measurements are performed by tuning the ECDL and scanning the sum-frequency-mixed radiation over strong nitric oxide absorption lines near 226 nm. In Year 1 of the research, the nitric oxide sensor was used for measurements in the exhaust of a coal-fired laboratory combustion facility. The Texas A&M University boiler burner facility is a 30 kW (100,000 Btu/hr) downward-fired furnace with a steel shell encasing ceramic insulation. Measurements of nitric oxide concentration in the exhaust stream were performed after modification of the facility for laser based NOx diagnostics. The diode-laser-based ultraviolet absorption measurements were successful even when the beam was severely attenuated by particulate in the exhaust stream and window fouling. Single-laser-sweep measurements were demonstrated with an effective time resolution of 100 msec, limited at this time by the scan rate of our mechanically tuned ECDL system. In Year 2, the Toptica ECDL in the original system was replaced with a Sacher Lasers ECDL. The mode-hop-free tuning range and tuning rate of the Toptica ECDL were 25 GHz and a few Hz, respectively. The mode-hop-free tuning range and tuning rate of the Sacher Lasers ECDL were 90 GHz and a few hundred Hz, respectively. The Sacher Lasers ECDL thus allows us to scan over the entire NO absorption line and to determine the absorption baseline with increased accuracy and precision. The increased tuning rate is an advantage in that data can be acquired much more rapidly and the

  9. Quantifying suspended sediment loads delivered to Cheney Reservoir, Kansas: Temporal patterns and management implications (United States)

    Stone, Mandy L.; Juracek, Kyle E.; Graham, Jennifer; Foster, Guy


    Cheney Reservoir, constructed during 1962 to 1965, is the primary water supply for the city of Wichita, the largest city in Kansas. Sediment is an important concern for the reservoir as it degrades water quality and progressively decreases water storage capacity. Long-term data collection provided a unique opportunity to estimate the annual suspended sediment loads for the entire history of the reservoir. To quantify and characterize sediment loading to Cheney Reservoir, discrete suspended sediment samples and continuously measured streamflow data were collected from the North Fork Ninnescah River, the primary inflow to Cheney Reservoir, over a 48-year period. Continuous turbidity data also were collected over a 15-year period. These data were used together to develop simple linear regression models to compute continuous suspended sediment concentrations and loads from 1966 to 2013. The inclusion of turbidity as an additional explanatory variable with streamflow improved regression model diagnostics and increased the amount of variability in suspended sediment concentration explained by 14%. Using suspended sediment concentration from the streamflow-only model, the average annual suspended sediment load was 102,517 t (113,006 tn) and ranged from 4,826 t (5,320 tn) in 1966 to 967,569 t (1,066,562 tn) in 1979. The sediment load in 1979 accounted for about 20% of the total load over the 48-year history of the reservoir and 92% of the 1979 sediment load occurred in one 24-hour period during a 1% annual exceedance probability flow event (104-year flood). Nearly 60% of the reservoir sediment load during the 48-year study period occurred in 5 years with extreme flow events (9% to 1% annual exceedance probability, or 11- to 104-year flood events). A substantial portion (41%) of sediment was transported to the reservoir during five storm events spanning only eight 24-hour periods during 1966 to 2013. Annual suspended sediment load estimates based on streamflow were, on

  10. Platform for monitoring water and solid fluxes in mountainous rivers (United States)

    Nord, Guillaume; Esteves, Michel; Aubert, Coralie; Belleudy, Philippe; Coulaud, Catherine; Bois, Jérôme; Geay, Thomas; Gratiot, Nicolas; Legout, Cédric; Mercier, Bernard; Némery, Julien; Michielin, Yoann


    The project aims to develop a platform that electronically integrates a set of existing sensors for the continuous measurement at high temporal frequency of water and solid fluxes (bed load and suspension), characteristics of suspended solids (distribution in particle size, settling velocity of the particles) and other variables on water quality (color, nutrient concentration). The project is preferentially intended for rivers in mountainous catchments draining areas from 10 to 1000 km², with high suspended sediment concentrations (maxima between 10 and 300 g/l) and highly dynamic behavior, water discharge varying of several orders of magnitude in a short period of time (a few hours). The measurement of water and solid fluxes in this type of river remains a challenge and, to date, there is no built-in device on the market to continuously monitor all these variables. The development of this platform is based on a long experience of measurement of sediment fluxes in rivers within the French Critical Zone Observatories (, especially in the Draix-Bléone ( and OHMCV ( observatories. The choice was made to integrate in the platform instruments already available on the market and currently used by the scientific community (water level radar, surface velocity radar, turbidity sensor, automatic water sampler, video camera) and to include also newly developed instruments (System for the Characterization of Aggregates and Flocs - see EGU2016-8542 - and hydrophone) or commercial instruments (spectrophotometer and radiometer) to be tested in surface water with high suspended sediment concentration. Priority is given to non-intrusive instruments due to their robustness in this type of environment with high destructive potential. Development work includes the construction of a platform prototype "smart" and remotely configurable for implantation in an isolated environment (absence of electric

  11. Pre-aged soil organic carbon as a major component of the Yellow River suspended load: Regional significance and global relevance (United States)

    Tao, Shuqin; Eglinton, Timothy I.; Montluçon, Daniel B.; McIntyre, Cameron; Zhao, Meixun


    Large rivers connect the continents and the oceans, and corresponding material fluxes have a global impact on marine biogeochemistry. The Yellow River transports vast quantities of suspended sediments to the ocean, yet the nature of the particulate organic carbon (POC) carried by this system is not well known. The focus of this study is to characterize the sources, composition and age of suspended POC collected near the terminus of this river system, focusing on the abundance and carbon isotopic composition (13C and 14C) of specific biomarkers. The concentrations of vascular plant wax lipids (long-chain (≥C24) n-alkanes, n-fatty acids) and POC co-varied with total suspended solid (TSS) concentrations, indicating that both were controlled by the overall terrestrial sediment flux. POC exhibited relatively uniform δ13C values (-23.8 to -24.2‰), and old radiocarbon ages (4000-4640 yr). However, different biomarkers exhibited a wide range of 14C ages. Short-chain (C16, C18) fatty acid 14C ages were variable but generally the youngest organic components (from 502 yr to modern), suggesting they reflect recently biosynthesized material. Lignin phenol 14C ages were also variable and relatively young (1070 yr to modern), suggesting rapid export of carbon from terrestrial primary production. In contrast, long-chain plant wax lipids display relatively uniform and significantly older 14C ages (1500-1800 yr), likely reflecting inputs of pre-aged, mineral-associated soil OC from the Yellow River drainage basin. Even-carbon-numbered n-alkanes yielded the oldest 14C ages (up to 26 000 yr), revealing the presence of fossil (petrogenic) OC. Two isotopic mass balance approaches were explored to quantitively apportion different OC sources in Yellow River suspended sediments. Results indicate that the dominant component of POC (53-57%) is substantially pre-aged (1510-1770 yr), and likely sourced from the extensive loess-paleosol deposits outcropping within the drainage basin. Of


    Directory of Open Access Journals (Sweden)

    Abdullah Abdullah


    Full Text Available The pineapple waste is contain high concentration of biodegradable organic material and suspended solid. As a result it has a high BOD and extremes of pH conditions. The pineapple wastes juice contains mainly sucrose, glucose, fructose and other nutrients. The characterisation this waste is needed to reduce it by  recycling to get raw material or  for  conversion into useful product of higher value added products such as organic acid, methane , ethanol, SCP and enzyme. Analysis of sugar indicates that liquid waste contains mainly sucrose, glucose and fructose.  The dominant sugar was fructose, glucose and sucrose.  The fructose and glucose levels were similar to each other, with fructose usually slightly higher than glucose. The total sugar and citric acid content were 73.76 and 2.18 g/l. The sugar content in solid waste is glucose and fructose was 8.24 and 12.17 %, no sucrose on this waste

  13. Surface tension of Nanofluid-type fuels containing suspended nanomaterials. (United States)

    Tanvir, Saad; Qiao, Li


    The surface tension of ethanol and n-decane based nanofluid fuels containing suspended aluminum (Al), aluminum oxide (Al2O3), and boron (B) nanoparticles as well as dispersible multi-wall carbon nanotubes (MWCNTs) were measured using the pendant drop method by solving the Young-Laplace equation. The effects of nanoparticle concentration, size and the presence of a dispersing agent (surfactant) on surface tension were determined. The results show that surface tension increases both with particle concentration (above a critical concentration) and particle size for all cases. This is because the Van der Waals force between particles at the liquid/gas interface increases surface free energy and thus increases surface tension. At low particle concentrations, however, addition of particles has little influence on surface tension because of the large distance between particles. An exception is when a surfactant was used or when (MWCNTs) was involved. For such cases, the surface tension decreases compared to the pure base fluid. The hypothesis is the polymer groups attached to (MWCNTs) and the surfactant layer between a particle and the surround fluid increases the electrostatic force between particles and thus reduce surface energy and surface tension.

  14. Surface tension of Nanofluid-type fuels containing suspended nanomaterials (United States)


    The surface tension of ethanol and n-decane based nanofluid fuels containing suspended aluminum (Al), aluminum oxide (Al2O3), and boron (B) nanoparticles as well as dispersible multi-wall carbon nanotubes (MWCNTs) were measured using the pendant drop method by solving the Young-Laplace equation. The effects of nanoparticle concentration, size and the presence of a dispersing agent (surfactant) on surface tension were determined. The results show that surface tension increases both with particle concentration (above a critical concentration) and particle size for all cases. This is because the Van der Waals force between particles at the liquid/gas interface increases surface free energy and thus increases surface tension. At low particle concentrations, however, addition of particles has little influence on surface tension because of the large distance between particles. An exception is when a surfactant was used or when (MWCNTs) was involved. For such cases, the surface tension decreases compared to the pure base fluid. The hypothesis is the polymer groups attached to (MWCNTs) and the surfactant layer between a particle and the surround fluid increases the electrostatic force between particles and thus reduce surface energy and surface tension. PMID:22513039

  15. The effects of colloidal SiO2 and inhibitor on the solid deposit formation in geothermal water of low hardness

    Directory of Open Access Journals (Sweden)

    Stanković Novica J.


    Full Text Available Low solubility of SiO2 and its occurrence in geothermal waters in the form of ionic, colloidal and suspended state are the main cause of the solid deposit occurrence. Certain chemical types of silica, under the influence of Fe2+, Al3+, F−, OH- ions and other micro-constituents, and due to significantly decreased solubility of SiO2, stimulate nucleation, particle growth and solid deposit formation. The aim of this paper is to inhibit the process of nucleation and solid deposit formation by adding originally designed inhibitor in the form of an emulsion, when the total concentration of the present and added colloidal SiO2 is beyond the solubility limit (120 mg/dm3. By turbidimetric, SEM, EDS and XRD analysis, the processes of solid deposit formation were investigated in Vranjska Banja (Serbia spa geothermal water source (water hardness of 4ºdH, and theoretical and practical conclusions were made.

  16. Monitoring of suspended sediment in South Tyrol (United States)

    Nadalet, Rudi; Dinale, Roberto; Pernter, Martin; Maraldo, Luca; Peterlin, Dieter; Richter, Arnold; Comiti, Francesco


    In the context of the EU Water Framework Directive (WFD), which aims to achieve a good status of European water bodies, the Hydrographic Office of the Autonomous Province of Bolzano (Italy) extended in 2014 its institutional activities including the monitoring of suspended sediment in the river channel network. Currently, the only active monitoring station is on the Adige River at the gauging station of Ponte Adige near Bolzano (drainage area 2705 km2). The applied monitoring strategy and the data analysis concept are both based on the guidelines issued by the Austrian Federal Ministry of Agriculture, Forestry, Environment and Water Management (BMLFUW). The results indicates that the temporal variability strongly differs during the investigated period (2014-2015). In addition to the analysis of precipitation and water discharge, temperature and lightning activity were also included to better understand the sediment transport dynamics observed at the station. In summer 2015, the combination of constantly high daily temperature throughout the Adige basin (which drove intense glacier melting in the headwaters) with a high frequency of convective rainfall events (90% more than in 2014, obtained through lightning detection), led to an annual mass of transported suspended sediment of 260000 t. Interestingly, this value is similar to the one estimated for 2014 (300000 t), which was characterized by very different meteorological conditions (colder and wetter summer), but with the occurrence of an important flood in August, which transported half of the annual amount. Finally, we can conclude that the adopted monitoring strategy is applicable for institutional aims in terms of costs as well as in terms of time effort. During the next years, other stations for suspended sediment monitoring are planned to be installed in the Province to cover the most important river segments.

  17. Active noise cancellation in a suspended interferometer

    CERN Document Server

    Driggers, Jennifer C; Pepper, Keenan; Adhikari, Rana


    We demonstrate feed-forward vibration isolation on a suspended Fabry-Perot interferometer using Wiener filtering and a variant of the common Least Mean Square (LMS) adaptive filter algorithm. We compare the experimental results with theoretical estimates of the cancellation efficiency. Using data from the recent LIGO Science Run, we also estimate the impact of this technique on full scale gravitational wave interferometers. In the future, we expect to use this technique to also remove acoustic, magnetic, and gravitational noise perturbations from the LIGO interferometers. This noise cancellation technique is simple enough to implement in standard laboratory environments and can be used to improve SNR for a variety of high precision experiments.

  18. Geodetic monitoring of suspended particles in rivers (United States)

    Kamnik, Rok; Maksimova, Daria; Kovačič, Boštjan


    There is a trend in modern approach to the management of space of collecting the spatial data, in order to obtain useful information. In this paper a research of suspended particles in the river Drava and Mura will be introduced. The goal is to connect different fields of water management in countries where the rivers Drava and Mura flows in purpose of water management sustainability. The methods such as GNSS for mapping cross sections of the river, the use of ADCP (Acoustic Doppler Current Profiler) measurement system and water sampling to monitor sediment in the water will be presented.

  19. Safety Harness For Work Under Suspended Load (United States)

    Sunoo, Su Young


    Safety device protects worker under suspended engine or other heavy load. Mechanically linked with load so if load should fall, worker yanked safely away. Worker wears chest-plate vest with straps crossing eye on back. Lower safety cable connected to eye extends horizontally away from worker to nearby wall, wrapped on pulley and extends upward to motion amplifier or reducer. Safety cables transform any sudden downward motion of overhanging load into rapid sideways motion of worker. Net catches worker, preventing worker from bumping against wall.

  20. Suspended-sediment loads in the lower Stillaguamish River, Snohomish County, Washington, 2014–15 (United States)

    Anderson, Scott A.; Curran, Christopher A.; Grossman, Eric E.


    Continuous records of discharge and turbidity at a U.S. Geological Survey (USGS) streamgage in the lower Stillaguamish River were paired with discrete measurements of suspended-sediment concentration (SSC) in order to estimate suspended-sediment loads over the water years 2014 and 2015. First, relations between turbidity and SSC were developed and used to translate the continuous turbidity record into a continuous estimate of SSC. Those concentrations were then used to predict suspended-sediment loads based on the current discharge record, reported at daily intervals. Alternative methods were used to in-fill a small number of days with either missing periods of turbidity or discharge records. Uncertainties in our predictions at daily and annual time scales were estimated based on the parameter uncertainties in our turbidity-SSC regressions. Daily loads ranged from as high as 121,000 tons during a large autumn storm to as low as –56 tons, when tidal return flow moved more sediment upstream than river discharge did downstream. Annual suspended-sediment loads for both water years were close to 1.4 ± 0.2 million tons.

  1. Vertical Distribution of Suspended Sediment under Steady Flow: Existing Theories and Fractional Derivative Model

    Directory of Open Access Journals (Sweden)

    Shiqian Nie


    Full Text Available The fractional advection-diffusion equation (fADE model is a new approach to describe the vertical distribution of suspended sediment concentration in steady turbulent flow. However, the advantages and parameter definition of the fADE model in describing the sediment suspension distribution are still unclear. To address this knowledge gap, this study first reviews seven models, including the fADE model, for the vertical distribution of suspended sediment concentration in steady turbulent flow. The fADE model, among others, describes both Fickian and non-Fickian diffusive characteristics of suspended sediment, while the other six models assume that the vertical diffusion of suspended sediment follows Fick’s first law. Second, this study explores the sensitivity of the fractional index of the fADE model to the variation of particle sizes and sediment settling velocities, based on experimental data collected from the literatures. Finally, empirical formulas are developed to relate the fractional derivative order to particle size and sediment settling velocity. These formulas offer river engineers a substitutive way to estimate the fractional derivative order in the fADE model.


    National Research Council Canada - National Science Library

    N A Sáenz; D E Paez; C Arango


      An empirical relationship of Total Suspended Sediments (TSS) concentrations and reflectance values obtained with Drones' aerial photos and processed using remote sensing tools was set up as the main objective of this research...

  3. REE in suspended particulate matter and sediment of the Zuari estuary and adjacent shelf, western India: Influence of mining and estuarine turbidity

    Digital Repository Service at National Institute of Oceanography (India)

    Shynu, R.; Rao, V.P.; Parthiban, G.; Balakrishnan, S.; Narvekar, T.; Kessarkar, P.M.

    Concentrations of Al, Fe, Mn and rare earth elements (REE) were measured in 122 samples of suspended particulate matter (SPM) and 70 surficial sediments from the Zuari estuary and the adjacent shelf to understand their distribution, provenance...

  4. An extensive study of the concentrations of particulate/dissolved radiocaesium derived from the Fukushima Dai-ichi Nuclear Power Plant accident in various river systems and their relationship with catchment inventory. (United States)

    Yoshimura, Kazuya; Onda, Yuichi; Sakaguchi, Aya; Yamamoto, Masayoshi; Matsuura, Yuki


    An extensive investigation of particulate radiocaesium in suspended solids and dissolved radiocaesium in river water was undertaken at 30 sites in Fukushima and Miyagi Prefectures in December 2012, and their relationships with catchment inventory and the solid/liquid distribution coefficient (Kd) were evaluated. Rivers located in the coastal region on the north side of the Fukushima Dai-ichi Nuclear Power Plant exhibited relatively higher particulate radiocaesium concentrations. Significant correlations were found between concentrations of particulate/dissolved radiocaesium and average catchment inventories, indicating that the concentrations of particulate/dissolved radiocaesium could be approximated from the catchment inventory. Particulate radiocaesium concentration was significantly correlated with dissolved radiocaesium concentration (with the exception of concentrations measured in estuaries), and the geometric mean Kd was calculated as 3.6 × 10(5) with a 95% confidence interval of 2.6-5.1 × 10(5). Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Aluminum Doped Parahydrogen Solids

    National Research Council Canada - National Science Library

    Fajardo, Mario


    ...) solids doped with large (- 1 %) concentrations of Al atoms. We incorporated into our apparatus a commercially available effusive Al atom source capable of delivering Al atom fluxes in excess of 10(exp 17...

  6. Tratamento anaeróbio de resíduos sólidos orgânicos com alta e baixa concentração de sólidos Anaerobic treatment of organic solid waste with high and low concentrations of solids

    Directory of Open Access Journals (Sweden)

    Valderi D. Leite


    Full Text Available A finalidade principal deste trabalho foi estudar o tratamento anaeróbio de resíduos sólidos orgânicos com alta e baixa concentração de sólidos. O sistema experimental se compunha de dois reatores com capacidade unitária de 2.200 L, enquanto o substrato utilizado era composto de resíduos sólidos vegetais e lodo de esgotos sanitários, sendo um dos reatores alimentado com substrato contendo 20% de sólidos totais (80% de umidade e o outro com apenas 5% de sólidos totais (95% de umidade. Verificou-se, quando da utilização de substrato contendo 5% (percentagem em peso de sólidos totais, que o tempo de retenção de sólidos requerido para que fossem alcançados 80% de redução da massa de DQO aplicada, foi de 90 dias, propiciando uma taxa de produção de gás metano de 0,25 Nm³ CH4 kg-1 DQO Aplicada. Com relação ao substrato contendo 20% de sólidos totais, o tempo de retenção de sólidos requerido para bioestabilizar 80% da massa de DQO aplicada, foi de 270 dias, com taxa de produção de gás metano de 0,10 Nm³ CH4 kg-1 DQO Aplicada.In this study the anaerobic treatment of organic solid waste with high and low concentrations of solids was studied. The experimental system comprised of two reactors, with unitary capacity of 2,200 L, while the used substrate was composed of solid vegetable waste and sludge. One of the reactors was loaded with substrate containing 20% of total solids and the other with only 5% of total solids on weight basis. It was verified that, for the substrate containing 5% of total solids, the retention time of solids required for 80% reduction of the applied COD mass was 90 days, during which the methane gas production rate was of 0.25 Nm³ kg-1 COD Applied; whereas in the substrate containing 20% of total solids, the retention time of solids required for biostabilization of 80% of the mass of applied COD was 270 days, with a methane gas production rate of 0.1 Nm³ CH4 kg-1 COD Applied.

  7. Elastic properties of suspended multilayer WSe2 (United States)

    Zhang, Rui; Koutsos, Vasileios; Cheung, Rebecca


    We report the experimental determination of the elastic properties of suspended multilayer WSe2, a promising two-dimensional (2D) semiconducting material combined with high optical quality. The suspended WSe2 membranes have been fabricated by mechanical exfoliation of bulk WSe2 and transfer of the exfoliated multilayer WSe2 flakes onto SiO2/Si substrates pre-patterned with hole arrays. Then, indentation experiments have been performed on these membranes with an atomic force microscope. The results show that the 2D elastic modulus of the multilayer WSe2 membranes increases linearly while the prestress decreases linearly as the number of layers increases. The interlayer interaction in WSe2 has been observed to be strong enough to prevent the interlayer sliding during the indentation experiments. The Young's modulus of multilayer WSe2 (167.3 ± 6.7 GPa) is statistically independent of the thickness of the membranes, whose value is about two thirds of other most investigated 2D semiconducting transition metal dichalcogenides, namely, MoS2 and WS2. Moreover, the multilayer WSe2 can endure ˜12.4 GPa stress and ˜7.3% strain without fracture or mechanical degradation. The 2D WSe2 can be an attractive semiconducting material for application in flexible optoelectronic devices and nano-electromechanical systems.

  8. Method for forming suspended micromechanical structures (United States)

    Fleming, James G.


    A micromachining method is disclosed for forming a suspended micromechanical structure from {111} crystalline silicon. The micromachining method is based on the use of anisotropic dry etching to define lateral features of the structure which are etched down into a {111}-silicon substrate to a first etch depth, thereby forming sidewalls of the structure. The sidewalls are then coated with a protection layer, and the substrate is dry etched to a second etch depth to define a spacing of the structure from the substrate. A selective anisotropic wet etchant (e.g. KOH, EDP, TMAH, NaOH or CsOH) is used to laterally undercut the structure between the first and second etch depths, thereby forming a substantially planar lower surface of the structure along a {111} crystal plane that is parallel to an upper surface of the structure. The lateral extent of undercutting by the wet etchant is controlled and effectively terminated by either timing the etching, by the location of angled {111}-silicon planes or by the locations of preformed etch-stops. This present method allows the formation of suspended micromechanical structures having large vertical dimensions and large masses while allowing for detailed lateral features which can be provided by dry etch definition. Additionally, the method of the present invention is compatible with the formation of electronic circuitry on the substrate.

  9. Estimation of Constituent Concentrations, Loads, and Yields in Streams of Johnson County, Northeast Kansas, Using Continuous Water-Quality Monitoring and Regression Models, October 2002 through December 2006 (United States)

    Rasmussen, Teresa J.; Lee, Casey J.; Ziegler, Andrew C.


    Johnson County is one of the most rapidly developing counties in Kansas. Population growth and expanding urban land use affect the quality of county streams, which are important for human and environmental health, water supply, recreation, and aesthetic value. This report describes estimates of streamflow and constituent concentrations, loads, and yields in relation to watershed characteristics in five Johnson County streams using continuous in-stream sensor measurements. Specific conductance, pH, water temperature, turbidity, and dissolved oxygen were monitored in five watersheds from October 2002 through December 2006. These continuous data were used in conjunction with discrete water samples to develop regression models for continuously estimating concentrations of other constituents. Continuous regression-based concentrations were estimated for suspended sediment, total suspended solids, dissolved solids and selected major ions, nutrients (nitrogen and phosphorus species), and fecal-indicator bacteria. Continuous daily, monthly, seasonal, and annual loads were calculated from concentration estimates and streamflow. The data are used to describe differences in concentrations, loads, and yields and to explain these differences relative to watershed characteristics. Water quality at the five monitoring sites varied according to hydrologic conditions; contributing drainage area; land use (including degree of urbanization); relative contributions from point and nonpoint constituent sources; and human activity within each watershed. Dissolved oxygen (DO) concentrations were less than the Kansas aquatic-life-support criterion of 5.0 mg/L less than 10 percent of the time at all sites except Indian Creek, which had DO concentrations less than the criterion about 15 percent of the time. Concentrations of suspended sediment, chloride (winter only), indicator bacteria, and pesticides were substantially larger during periods of increased streamflow. Suspended

  10. Elemental Spatiotemporal Variations of Total Suspended Particles in Jeddah City

    Directory of Open Access Journals (Sweden)

    Mohammad W. Kadi


    Full Text Available Elements associated with total suspended particulate matter (TSP in Jeddah city were determined. Using high-volume samplers, TSP samples were simultaneously collected over a one-year period from seven sampling sites. Samples were analyzed for Al, Ba, Ca, Cu, Mg, Fe, Mn, Zn, Ti, V, Cr, Co, Ni, As, and Sr. Results revealed great dependence of element contents on spatial and temporal variations. Two sites characterized by busy roads, workshops, heavy population, and heavy trucking have high levels of all measured elements. Concentrations of most elements at the two sites exhibit strong spatial gradients and concentrations of elements at these sites are higher than other locations. The highest concentrations of elements were observed during June–August because of dust storms, significant increase in energy consumption, and active surface winds. Enrichment factors of elements at the high-level sites have values in the range >10~60 while for Cu and Zn the enrichment factors are much higher (~0–>700 indicating that greater percentage of TSP composition for these three elements in air comes from anthropogenic activities.

  11. Separation of solids and disinfection for agronomical use of the effluent from a UASB reactor. (United States)

    Sundefeld Junior, G C; Piveli, R P; Cutolo, S A; Ferreira Filho, S S; Santos, J G


    The present work addresses the preparation of the effluent from a full-scale upflow anaerobic sludge blanket (UASB) reactor for drip irrigation of orange crops. The pilot plant included a lamella plate clarifier followed by a geo-textile blanket filter and a UV disinfection reactor. The clarifier operated with a surface load of 115 m(3)m(-2)d(-1), whereas the filter operated with 10 m(3)m(-2)d(-1). The UV reactor was an open-channel type and the effective dose was approximately 2.8 W h m(-3). The effluent of the UASB reactor received 0.5 mg L(-1) cationic polyelectrolyte before entering the high-rate clarifier. Suspended solids' concentrations and Escherichia coli and helminth egg's densities were monitored throughout the treatment system for 12 months. Results showed that the total suspended solids concentration in the filter effluent was lower than 7 mg L(-1) and helminth density was below 1.0 egg L(-1). The UV disinfection demonstrated the ability to produce a final effluent with E. coli density lower than 10(3)MPN/100 mL (MPN: most probable number) during the entire process. Thus, the World Health Organization standards for unrestricted crop use were met. Agronomic interest parameters were controlled and it was possible to identify the important contribution of treated sewage in terms of the main nutrients.

  12. Environmentally-suspended sediment production of the Nasia River ...

    African Journals Online (AJOL)

    The study assessed the level of suspended sediment produced in the Nasia River Basin. Hydrological and meteorological data and water samples were used for the study. Average suspended sediment yield (33 years) in the basin was 19.90 t/km2/yr. With mean annual runoff of 439.13m3/s, 322.43 t/yr suspended sediment ...

  13. Documentation of hydrochemical-facies data and ranges of dissolved-solids concentrations for the northern Atlantic Coastal Plain aquifer system, New Jersey, Delaware, Maryland, Virginia and North Carolina supplement to Professional paper 1404-L (United States)

    Meisler, Harold; Knobel, L.L.


    Hydrochemical-facies data and ranges of dissolved- solids concentrations used to construct hydrochemical-facies maps and sections for U.S. Geological Survey Professional Paper 1404-L have not been previously published. In this report, the data are contained on a 3-1/2 high-density diskette in a file presented in American International Standard Code for Information Exchange (ASCII) format. The file requires about 0.2 megabyte of disk space on an IBM-compatible microcomputer using the MS-DOS operating system.

  14. Determination of chemical oxygen demand in heterogeneous solid or semisolid samples using a novel method combining solid dilutions as a preparation step followed by optimized closed reflux and colorimetric measurement. (United States)

    Noguerol-Arias, Joan; Rodríguez-Abalde, Angela; Romero-Merino, Eva; Flotats, Xavier


    This paper reports the development of an innovative sample preparation method for the determination of the chemical oxygen demand (COD) in heterogeneous solid or semisolid samples, with high suspended solids and COD concentrations, using an optimized closed reflux colorimetric method. The novel method, named solid dilution (SD), is based on a different technique of sample preparation, diluting the sample with magnesium sulfate (MgSO(4)) previous to COD determination. With this, it is possible to obtain a solid homogeneous mixture much more easily analyzable. Besides, a modification of concentration and ratio of reagents was optimized to make the closed reflux colorimetric method suitable for complex substrates with COD levels ranging from 5 to 2500 g O(2) kg(-1) TS. The optimized method has been tested with potassium hydrogen phthalate (KHP) as primary solid standard and using different solid or semiliquid substrates like pig slaughterhouse waste and sewage sludge, among others. Finally, the optimized method (SD/SM-CRC) was intensively tested in comparison to the standard titrimetric method (SM-ORT) using different certified reference materials (CRM). The developed method was found to give higher accuracy, 1.4% relative standard deviation (RSD) vs 10.4%, and bias of 2.8% vs 8.0%, in comparison to the standard open reflux titrimetric method.

  15. Near bed suspended sediment flux by single turbulent events (United States)

    Amirshahi, Seyed Mohammad; Kwoll, Eva; Winter, Christian


    The role of small scale single turbulent events in the vertical mixing of near bed suspended sediments was explored in a shallow shelf sea environment. High frequency velocity and suspended sediment concentration (SSC; calibrated from the backscatter intensity) were collected using an Acoustic Doppler Velocimeter (ADV). Using quadrant analysis, the despiked velocity time series was divided into turbulent events and small background fluctuations. Reynolds stress and Turbulent Kinetic Energy (TKE) calculated from all velocity samples, were compared to the same turbulent statistics calculated only from velocity samples classified as turbulent events (Reevents and TKEevents). The comparison showed that Reevents and TKEevents was increased 3 and 1.6 times, respectively, when small background fluctuations were removed and that the correlation with SSC for TKE could be improved through removal of the latter. The correlation between instantaneous vertical turbulent flux (w ‧) and SSC fluctuations (SSC ‧) exhibits a tidal pattern with the maximum correlation at peak ebb and flood currents, when strong turbulent events appear. Individual turbulent events were characterized by type, strength, duration and length. Cumulative vertical turbulent sediment fluxes and average SSC associated with individual turbulent events were calculated. Over the tidal cycle, ejections and sweeps were the most dominant events, transporting 50% and 36% of the cumulative vertical turbulent event sediment flux, respectively. Although the contribution of outward interactions to the vertical turbulent event sediment flux was low (11%), single outward interaction events were capable of inducing similar SSC ‧ as sweep events. The results suggest that on time scales of tens of minutes to hours, TKE may be appropriate to quantify turbulence in sediment transport studies, but that event characteristics, particular the upward turbulent flux need to be accounted for when considering sediment transport

  16. Thematic mapper research in the earth sciences: Small scale patches of suspended matter and phytoplankton in the Elbe River Estuary, German Bight and Tidal Flats (United States)

    Grassl, H.; Doerffer, R.; Fischer, J.; Brockmann, C.; Stoessel, M.


    A Thematic Mapper (TM) field experiment was followed by a data analysis to determine TM capabilities for analysis of suspended matter and phytoplankton. Factor analysis showed that suspended matter concentration, atmospheric scattering, and sea surface temperature can be retrieved as independent factors which determine the variation in the TM data over water areas. Spectral channels in the near infrared open the possibility of determining the Angstrom exponent better than for the coastal zone color scanner. The suspended matter distribution may then be calculated by the absolute radiance of channel 2 or 3 or the ratio of both. There is no indication of whether separation of chlorophyll is possible. The distribution of suspended matter and sea surface temperature can be observed with the expected fine structure. A good correlation between water depth and suspended matter distribution as found from ship data can now be analyzed for an entire area by the synoptic view of the TM scenes.

  17. Sediment fingerprinting to determine the source of suspended sediment in a southern Piedmont stream. (United States)

    Mukundan, R; Radcliffe, D E; Ritchie, J C; Risse, L M; McKinley, R A


    Thousands of stream miles in the southern Piedmont region are impaired because of high levels of suspended sediment. It is unclear if the source is upland erosion from agricultural sources or bank erosion of historic sediment deposited in the flood plains between 1830 and 1930 when cotton farming was extensive. The objective of this study was to determine the source of high stream suspended sediment concentrations in a typical southern Piedmont watershed using sediment fingerprinting techniques. Twenty-one potential tracers were tested for their ability to discriminate between sources, conservative behavior, and lack of redundancy. Tracer concentrations were determined in potential sediment sources (forests, pastures, row crop fields, stream banks, and unpaved roads and construction sites), and suspended sediment samples collected from the stream and analyzed using mixing models. Results indicated that 137Cs and 15N were the best tracers to discriminate potential sediment sources in this watershed. The delta15N values showed distinct signatures in all the potential suspended sediment sources, and delta15N was a unique tracer to differentiate stream bank soil from upland subsurface soils, such as soil from construction sites, unpaved roads, ditches, and field gullies. Mixing models showed that about 60% of the stream suspended sediment originated from eroding stream banks, 23 to 30% from upland subsoil sources (e.g., construction sites and unpaved roads), and about 10 to 15% from pastures. The results may be applicable to other watersheds in the Piedmont depending on the extent of urbanization occurring in these watersheds. Better understanding of the sources of fine sediment has practical implications on the type of sediment control measures to be adopted. Investment of resources in improving water quality should consider the factors causing stream bank erosion and erosion from unpaved roads and construction sites to water quality impairment.

  18. Exposure of clownfish larvae to suspended sediment levels found on the Great Barrier Reef: Impacts on gill structure and microbiome. (United States)

    Hess, Sybille; Wenger, Amelia S; Ainsworth, Tracy D; Rummer, Jodie L


    Worldwide, increasing coastal development has played a major role in shaping coral reef species assemblages, but the mechanisms underpinning distribution patterns remain poorly understood. Recent research demonstrated delayed development in larval fishes exposed to suspended sediment, highlighting the need to further understand the interaction between suspended sediment as a stressor and energetically costly activities such as growth and development that are essential to support biological fitness. We examined the gill morphology and the gill microbiome in clownfish larvae (Amphiprion percula) exposed to suspended sediment concentrations (using Australian bentonite) commonly found on the inshore Great Barrier Reef. The gills of larvae exposed to 45 mg L(-1) of suspended sediment had excessive mucous discharge and growth of protective cell layers, resulting in a 56% thicker gill epithelium compared to fish from the control group. Further, we found a shift from 'healthy' to pathogenic bacterial communities on the gills, which could increase the disease susceptibility of larvae. The impact of suspended sediments on larval gills may represent an underlying mechanism behind the distribution patterns of fish assemblages. Our findings underscore the necessity for future coastal development to consider adverse effects of suspended sediments on fish recruitment, and consequently fish populations and ecosystem health.

  19. Biologically Induced Deposition of Fine Suspended Particles by Filter-Feeding Bivalves in Land-Based Industrial Marine Aquaculture Wastewater (United States)

    Zhou, Yi; Zhang, Shaojun; Liu, Ying; Yang, Hongsheng


    Industrial aquaculture wastewater contains large quantities of suspended particles that can be easily broken down physically. Introduction of macro-bio-filters, such as bivalve filter feeders, may offer the potential for treatment of fine suspended matter in industrial aquaculture wastewater. In this study, we employed two kinds of bivalve filter feeders, the Pacific oyster Crassostrea gigas and the blue mussel Mytilus galloprovincialis, to deposit suspended solids from marine fish aquaculture wastewater in flow-through systems. Results showed that the biodeposition rate of suspended particles by C. gigas (shell height: 8.67±0.99 cm) and M. galloprovincialis (shell height: 4.43±0.98 cm) was 77.84±7.77 and 6.37±0.67 mg ind−1•d−1, respectively. The total solid suspension (TSS) deposition rates of oyster and mussel treatments were 3.73±0.27 and 2.76±0.20 times higher than that of the control treatment without bivalves, respectively. The TSS deposition rates of bivalve treatments were significantly higher than the natural sedimentation rate of the control treatment (Paquaculture wastewater, and simultaneously yield value-added biological products. PMID:25250730

  20. Biologically induced deposition of fine suspended particles by filter-feeding bivalves in land-based industrial marine aquaculture wastewater. (United States)

    Zhou, Yi; Zhang, Shaojun; Liu, Ying; Yang, Hongsheng


    Industrial aquaculture wastewater contains large quantities of suspended particles that can be easily broken down physically. Introduction of macro-bio-filters, such as bivalve filter feeders, may offer the potential for treatment of fine suspended matter in industrial aquaculture wastewater. In this study, we employed two kinds of bivalve filter feeders, the Pacific oyster Crassostrea gigas and the blue mussel Mytilus galloprovincialis, to deposit suspended solids from marine fish aquaculture wastewater in flow-through systems. Results showed that the biodeposition rate of suspended particles by C. gigas (shell height: 8.67 ± 0.99 cm) and M. galloprovincialis (shell height: 4.43 ± 0.98 cm) was 77.84 ± 7.77 and 6.37 ± 0.67 mg ind(-1) • d(-1), respectively. The total solid suspension (TSS) deposition rates of oyster and mussel treatments were 3.73 ± 0.27 and 2.76 ± 0.20 times higher than that of the control treatment without bivalves, respectively. The TSS deposition rates of bivalve treatments were significantly higher than the natural sedimentation rate of the control treatment (P treatments were significantly lower than those in the sediments of the control (P aquaculture wastewater, and simultaneously yield value-added biological products.

  1. Development of methodology and correlations to predict solids concentration profile during oil well drilling static periods; Desenvolvimento de metodologia e correlacoes para previsao de perfil de concentracao de solidos durante a perfuracao de pocos de petroleo em periodos de estatica

    Energy Technology Data Exchange (ETDEWEB)

    Gandelman, Roni Abensur [Centro de Pesquisas da Petrobras (CENPES). Gerencia de Interacao Rocha-Fluido (Brazil)], e-mail:; Pinto, Gustavo Henrique Vieira Pereira [E and P Norte-Nordeste. Gerencia de Intervencao e Perfuracao de Pocos - BA (Brazil)], e-mail:


    One of the main function of drilling fluid is to transport solids, generated by the bit, to the surface. Therefore, gelation is an important and desirable drilling fluid characteristic as it avoids solids sedimentation during pump -off periods. However, when circulation is resumed, an extra energy is required to break the gelled structure. Consequently, bottom-hole pressure peaks are observed and this may represent an operational risk if the fracture pressure is reached. The risk is especially high in narrow operational window scenarios, typical of deep and ultra-deep water environments. On the other hand, gelled fluids may not avoid some heavier and/or larger particles settling. It is therefore important to understand how particles settle in gelled fluids (and while the gelled structure is forming) to predict the solid concentration profiles during and after pump -off periods. This prediction is very important as it can help operators to avoid operational problems. This study developed a methodology to predict particles sedimentation in gelled fluids and pressure peaks when circulation is resumed. To develop the correlations and predict pressure peaks, several experiments were carried out with rheometers and field viscosimeters in transient and stationary conditions. The results were used to build a model that is currently being used with very promising results. (author)

  2. Rheology Measurements for Online Monitoring of Solids in Activated Sludge Reactors of Municipal Wastewater Treatment Plant

    Directory of Open Access Journals (Sweden)

    Luciano Piani


    Full Text Available Rheological behaviour of recycled sludge from a secondary clarifier of a municipal wastewater treatment plant was studied by using the rate controlled coaxial cylinder viscometer Rotovisko-Haake 20, system M5-osc., measuring device NV. The tests (hysteresis cycles were performed under continuous flow conditions and following an ad hoc measurement protocol. Sludge shear stress versus shear rate curves were fitted very satisfactorily by rheological models. An experimental equation correlating the solid concentration of sludge to relative viscosity and fitting satisfactorily flow curves at different Total Suspended Solids (TTS% was obtained. Application of the empirical correlation should allow the monitoring of the proper functioning of a wastewater treatment plant measuring viscosity of sludge.

  3. Tracking suspended particle transport via radium isotopes ((226)Ra and (228)Ra) through the Apalachicola-Chattahoochee-Flint River system. (United States)

    Peterson, Richard N; Burnett, William C; Opsahl, Stephen P; Santos, Isaac R; Misra, Sambuddha; Froelich, Philip N


    Suspended particles in rivers can carry metals, nutrients, and pollutants downstream which can become bioactive in estuaries and coastal marine waters. In river systems with multiple sources of both suspended particles and contamination sources, it is important to assess the hydrologic conditions under which contaminated particles can be delivered to downstream ecosystems. The Apalachicola-Chattahoochee-Flint (ACF) River system in the southeastern United States represents an ideal system to study these hydrologic impacts on particle transport through a heavily-impacted river (the Chattahoochee River) and one much less impacted by anthropogenic activities (the Flint River). We demonstrate here the utility of natural radioisotopes as tracers of suspended particles through the ACF system, where particles contaminated with arsenic (As) and antimony (Sb) have been shown to be contributed from coal-fired power plants along the Chattahoochee River, and have elevated concentrations in the surficial sediments of the Apalachicola Bay Delta. Radium isotopes ((228)Ra and (226)Ra) on suspended particles should vary throughout the different geologic provinces of this river system, allowing differentiation of the relative contributions of the Chattahoochee and Flint Rivers to the suspended load delivered to Lake Seminole, the Apalachicola River, and ultimately to Apalachicola Bay. We also use various geochemical proxies ((40)K, organic carbon, and calcium) to assess the relative composition of suspended particles (lithogenic, organic, and carbonate fractions, respectively) under a range of hydrologic conditions. During low (base) flow conditions, the Flint River contributed 70% of the suspended particle load to both the Apalachicola River and the bay, whereas the Chattahoochee River became the dominant source during higher discharge, contributing 80% of the suspended load to the Apalachicola River and 62% of the particles entering the estuary. Neither of these hydrologic

  4. The phosphorus content of fluvial suspended sediment in three lowland groundwater-dominated catchments (United States)

    Ballantine, Deborah J.; Walling, Desmond E.; Collins, Adrian L.; Leeks, Graham J. L.


    SummaryThis paper reports an investigation of the phosphorus (P) content of fluvial suspended sediment samples collected from three lowland groundwater-dominated agricultural catchments in the UK. In-stream trap samplers were installed at a total of 21 locations in the catchments of the Rivers Frome and Piddle in Dorset and in the Upper Tern in Shropshire, UK. Time-integrated suspended sediment samples ( n = 187) were collected at regular intervals over a period of 22 months and analysed for total phosphorus (TP), inorganic phosphorus (IP), organic phosphorus (OP) and algal available phosphorus (AAP). TP concentrations varied between sampling sites in the Rivers Frome and Piddle, allowing key P inputs to be identified, while fractionation of P assisted in identifying the nature of these inputs. There was also significant variation in both the TP concentration and the concentration of individual fractions between the Frome and Piddle catchments and the Upper Tern. These contrasts were attributed to the differing underlying geologies, since the Frome and Piddle are underlain predominantly by chalk, whilst the Upper Tern is underlain by sandstone, and also to the different soil types present. The TP content of suspended sediment collected from the Frome catchment showed a statistically significant relationship with specific surface area, but this relationship was not found for the remaining catchments. Temporal variation in P concentrations at both the seasonal and event scale was also investigated. Seasonal variations were noted for TP concentrations and for the concentrations of IP, OP and AAP in all the study catchments, but no consistent seasonal patterns were discernible. Maximum and minimum concentrations of the individual fractions occurred during different months in each of the study catchments, suggesting that different controls operated in the individual catchments. Short-term temporal variations in TP concentrations were documented for two high flow events

  5. Comparison of semipermeable membrane device (SPMD) and large-volume solid-phase extraction techniques to measure water concentrations of 4,4'-DDT, 4,4'-DDE, and 4,4'-DDD in Lake Chelan, Washington. (United States)

    Ellis, Steven G; Booij, Kees; Kaputa, Mike


    Semipermeable membrane devices (SPMDs) spiked with the performance reference compound PCB29 were deployed 6.1 m above the sediments of Lake Chelan, Washington, for a period of 27 d, to estimate the dissolved concentrations of 4,4'-DDT, 4,4'-DDE, and 4,4'-DDD. Water concentrations were estimated using methods proposed in 2002 and newer equations published in 2006 to determine how the application of the newer equations affects historical SPMD data that used the older method. The estimated concentrations of DDD, DDE, and DDD calculated using the older method were 1.5-2.9 times higher than the newer method. SPMD estimates from both methods were also compared to dissolved and particulate DDT concentrations measured directly by processing large volumes of water through a large-volume solid-phase extraction device (Infiltrex 300). SPMD estimates of DDD+DDE+DDT (SigmaDDT) using the older and newer methods were lower than Infiltrex concentrations by factors of 1.1 and 2.3, respectively. All measurements of DDT were below the Washington State water quality standards for the protection of human health (0.59 ng l(-1)) and aquatic life (1.0 ng l(-1)).

  6. Suspended Sediment and Phosphorus Removal in a Woodchip Filter System Treating Agricultural Wash Water. (United States)

    Choudhury, Tahina; Robertson, Will Dean; Finnigan, Darryl S


    Woodchip filters have received attention in recent years for their ability to sustain denitrification activity across multiyear time frames. However, in some freshwater aquatic ecosystems, P rather than N is the nutrient considered most responsible for eutrophication. Previous studies have indicated that woodchip filters have limited ability to remove dissolved P, but in agricultural terrain, P export in watercourses is often dominated by particulate P (PP). Woodchip media, because of their high porosity and permeability and the surface roughness of the particles, could be effective for PP removal. In this study, we tested a woodchip filter for its ability to remove suspended sediment and associated PP at a farm in southern Ontario, Canada, where vegetable wash water with extremely high total suspended solids (TSS) was generated. The treatment system consisted of a 12.3-m concrete sedimentation tank and a slightly larger woodchip filter (16.1 m) installed in a subsurface trench. During 7 mo of full-scale operation, treating 10.8 m d, the filter system removed 71% of influent total P (TP) averaging 8.8 mg L and 99% of TSS averaging 5800 mg L, with most of the removal occurring in the tank and a lesser amount (6-16%) occurring in the woodchip filter. Almost all of the TP removal was associated with PP (91% removal) because dissolved P, averaging 1.5 mg L in the wash water, was little changed. Woodchip filters, when coupled with a solids settling tank, have the potential to provide high-capacity, low-maintenance treatment of suspended solids and associated particulate P in turbid waters. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  7. Tratamento anaeróbio de resíduos orgânicos com baixa concentração de sólidos Anaerobic treatment of organic wastes with low concentration of solids

    Directory of Open Access Journals (Sweden)

    Maria L. D. de Luna


    Full Text Available Este trabalho foi realizado com o objetivo de avaliar o desempenho de reator anaeróbio compartimentado no tratamento de resíduos sólidos orgânicos com baixa concentração de sólidos. O reator anaeróbio compartimentado possuía capacidade unitária de 2.200 litros, era dividido em seis câmaras de iguais dimensões e foi operado com tempo de retenção de sólidos de 90 dias. Os resíduos sólidos orgânicos utilizados para alimentação do reator eram constituídos de resíduos sólidos vegetais e de lodo de esgoto sanitário na proporção de 80% e 20%, respectivamente. A mistura desses dois tipos de resíduos originava o substrato, o qual, após a correção da umidade para 95% (percentagem em massa, era alimentado ao reator. A eficiência de redução de material carbonáceo situou-se em torno de 80%, com carga orgânica aplicada de 9,3 kg R SO m-3 dia-1. A taxa de produção de biogás obtida foi de 5,6 L kg-1substrato (base úmida, com percentagem em volume de 50% de gás metano.The object of this study was to evaluate the use of a compartmented anaerobic reactor to treat organic solid waste with low concentration of solids. The reactor with a total capacity of 2.200 liters, divided into 6 equal chambers, was operated at a solid retention time of 90 days. The organic solids used to feed the reactor were comprised by vegetable residues and sanitary sludge in the proportion 80% and 20% respectively. The mixture of these two types of residues after the humidity correction to 95% (percentage by weight was used to feed the reactor. The removal efficiency of carbonaceous material was approximately 80% at an organic loading of 9.3 kg residual organic solids m-3 d-1. The rate of biogas production was 5.6 L kg-1substrate (wet weight with a methane concentration of 50% by volume.

  8. Design consideration for magnetically suspended flywheel systems (United States)

    Anand, D.; Kirk, J. A.; Frommer, D. A.


    Consideration is given to the design, fabrication, and testing of a magnetically suspended flywheel system for energy storage applications in space. The device is the prototype of a system combining passive suspension of the flywheel plate by samarium cobalt magnets and active control in the radial direction using eight separate magnetic coils. The bearing assembly was machined from a nickel-iron alloy, and the machine parts are all hydrogen annealed. Slots in the magnetic plate allow four independent quadrants for control. The motor/generator component of the system is a brushless dc-permanent magnetic/ironless engine using electronic communication. The system has been tested at over 2500 rpm with satisfactory results. The system characteristics of the flywheel for application in low earth orbit (LEO) are given in a table.

  9. Batch fabrication of nanotubes suspended between microelectrodes

    DEFF Research Database (Denmark)

    Mateiu, Ramona Valentina; Stöckli, T.; Knapp, H. F.


    We report a fabrication method, which uses standard UV-lithography to pattern the catalyst for the chemical vapour deposition(CVD) of suspended double clamped single walled carbon nanotubes. By using an aqueous solution of Fe(NO3)3 the patterning of the catalyst material onto microelectrodes can...... be done with a simple lift-off process with standard photolithographic resist. An applied electric field is sustained between the microelectrodes during CVD to guide the nanotube growth. Comparison with simulations shows that the location and the orientation of the grown carbon nanotubes (CNT) correspond...... to the regions of maximum electric field, enabling accurate positioning of a nanotube by controlling the shape of the microelectrodes. The CNT bridges are deflected tens of nm when a DC voltage is applied between the nanotube and a gate microelectrode indicating that the clamping through the catalyst particles...

  10. Treating municipal solid waste leachate in a pilot scale upflow anaerobic sludge blanket reactor under tropical temperature

    Directory of Open Access Journals (Sweden)

    Abbas Alizadeh Shooshtari


    Full Text Available Aims: The objective of this study was to investigate an Upflow Anaerobic Sludge Blanket (UASB reactor efficiency in treating municipal landfill leachate, under tropical temperature. Materials and Methods: A 30-liter pilot-scale UASB reactor was used to treat the municipal solid waste leachate, under tropical temperature, for 230 days. The reactor was inoculated with 10 liters of anaerobic sludge from an anaerobic digester, in an agro industry′s wastewater treatment plant. The Volatile Suspended Solids (VSS of sludge were 65 g/L, with volatile suspended solids to suspended solids (VSS/SS ratio of 0.74. The reactor was operated in mesophilic (34 - 39°C temperature. Results: After reaching a stable operation, the reactor was exposed to raw leachate, with mean chemical oxygen demand (COD concentrations of 35 g/L. The leachate was diluted to 9 - 10 g/L at Organic Loading Rates (OLRs of 2, 6, 12, 15 g COD/L.d and decreased again to 12 g COD/L.d, resulting in 45, 76, 84, 68, and 79% removal efficiency and increased again to 87% removal efficiency for COD, at Hydraulic Retention Times (HRTs of 6, 1.6, 0.83, and 0.67 days, respectively, in the UASB. In the reactor used in this study, the heavy metals were removed by adsorption on biomass, and the maximum removal rate was 68% for Zinc (Zn. Conclusions: It was concluded that the optimum OLR for diluted leachate up to 10 g COD/l, was 12 g COD/L.d at an HRT of 0.67 day (16 hours.

  11. Substantial export of suspended sediment to the global oceans from glacial erosion in Greenland (United States)

    Overeem, I.; Hudson, B. D.; Syvitski, J. P. M.; Mikkelsen, A. B.; Hasholt, B.; van den Broeke, M. R.; Noël, B. P. Y.; Morlighem, M.


    Limited measurements along Greenland's remote coastline hamper quantification of the sediment and associated nutrients draining the Greenland ice sheet, despite the potential influence of river-transported suspended sediment on phytoplankton blooms and carbon sequestration. Here we calibrate satellite imagery to estimate suspended sediment concentration for 160 proglacial rivers across Greenland. Combining these suspended sediment reconstructions with numerical calculations of meltwater runoff, we quantify the amount and spatial pattern of sediment export from the ice sheet. We find that, although runoff from Greenland represents only 1.1% of the Earth's freshwater flux, the Greenland ice sheet produces approximately 8% of the modern fluvial export of suspended sediment to the global ocean. Sediment loads are highly variable between rivers, consistent with observed differences in ice dynamics and thus with control by glacial erosion. Rivers that originate from deeply incised, fast-moving glacial tongues form distinct sediment-export hotspots: just 15% of Greenland's rivers transport 80% of the total sediment load of the ice sheet. We conclude that future acceleration of melt and ice sheet flow may increase sediment delivery from Greenland to its fjords and the nearby ocean.

  12. Influence of thermal hydrolysis-anaerobic digestion treatment of wastewater solids on concentrations of Triclosan, Triclocarban, and their transformation products in biosolids (United States)

    The growing concern worldwide regarding the presence of emerging contaminants in biosolids calls for a better understanding of how different treatment technologies at water resource recovery facilities (WRRFs) can influence concentrations prior to biosolids land application. This study focuses on t...

  13. An assessment of the suspended sediment rating curve approach for load estimation on the Rivers Bandon and Owenabue, Ireland (United States)

    Harrington, Seán T.; Harrington, Joseph R.


    This paper presents an assessment of the suspended sediment rating curve approach for load estimation on the Rivers Bandon and Owenabue in Ireland. The rivers, located in the South of Ireland, are underlain by sandstone, limestones and mudstones, and the catchments are primarily agricultural. A comprehensive database of suspended sediment data is not available for rivers in Ireland. For such situations, it is common to estimate suspended sediment concentrations from the flow rate using the suspended sediment rating curve approach. These rating curves are most commonly constructed by applying linear regression to the logarithms of flow and suspended sediment concentration or by applying a power curve to normal data. Both methods are assessed in this paper for the Rivers Bandon and Owenabue. Turbidity-based suspended sediment loads are presented for each river based on continuous (15 min) flow data and the use of turbidity as a surrogate for suspended sediment concentration is investigated. A database of paired flow rate and suspended sediment concentration values, collected between the years 2004 and 2011, is used to generate rating curves for each river. From these, suspended sediment load estimates using the rating curve approach are estimated and compared to the turbidity based loads for each river. Loads are also estimated using stage and seasonally separated rating curves and daily flow data, for comparison purposes. The most accurate load estimate on the River Bandon is found using a stage separated power curve, while the most accurate load estimate on the River Owenabue is found using a general power curve. Maximum full monthly errors of - 76% to + 63% are found on the River Bandon with errors of - 65% to + 359% found on the River Owenabue. The average monthly error on the River Bandon is - 12% with an average error of + 87% on the River Owenabue. The use of daily flow data in the load estimation process does not result in a significant loss of accuracy on