WorldWideScience

Sample records for surfactant triton x-100

  1. Utilization of Triton X-100 and polyethylene glycols during surfactant-mediated biodegradation of diesel fuel

    International Nuclear Information System (INIS)

    Wyrwas, Bogdan; Chrzanowski, Łukasz; Ławniczak, Łukasz; Szulc, Alicja; Cyplik, Paweł; Białas, Wojciech; Szymański, Andrzej; Hołderna-Odachowska, Aleksandra

    2011-01-01

    Highlights: ► Efficient degradation of Triton X-100 under both aerobic and aerobic conditions. ► Triton X-100 was most likely degraded via the ‘central fission’ mechanism. ► Preferential degradation of Triton X-100 over diesel oil. ► The presence of surfactants decreased diesel oil biodegradation efficiency. - Abstract: The hypothesis regarding preferential biodegradation of surfactants applied for enhancement of microbial hydrocarbons degradation was studied. At first the microbial degradation of sole Triton X-100 by soil isolated hydrocarbon degrading bacterial consortium was confirmed under both full and limited aeration with nitrate as an electron acceptor. Triton X-100 (600 mg/l) was utilized twice as fast for aerobic conditions (t 1/2 = 10.3 h), compared to anaerobic conditions (t 1/2 = 21.8 h). HPLC/ESI-MS analysis revealed the preferential biodegradation trends in both components classes of commercial Triton X-100 (alkylphenol ethoxylates) as well as polyethylene glycols. The obtained results suggest that the observed changes in the degree of ethoxylation for polyethylene glycol homologues occurred as a consequence of the ‘central fission’ mechanism during Triton X-100 biodegradation. Subsequent experiments with Triton X-100 at approx. CMC concentration (150 mg/l) and diesel oil supported our initial hypothesis that the surfactant would become the preferred carbon source even for hydrocarbon degrading bacteria. Regardless of aeration regimes Triton X-100 was utilized within 48–72 h. Efficiency of diesel oil degradation was decreased in the presence of surfactant for aerobic conditions by approx. 25% reaching 60 instead of 80% noted for experiments without surfactant. No surfactant influence was observed for anaerobic conditions.

  2. Surfactant-enhanced remediation of a trichloroethene-contaminated aquifer. 1. Transport of triton X-100

    Science.gov (United States)

    Smith, J.A.; Sahoo, D.; Mclellan, H.M.; Imbrigiotta, T.E.

    1997-01-01

    Transport of a nonionic surfactant (Triton X-100) at aqueous concentrations less than 400 mg/L through a trichloroethene-contaminated sand-and-gravel aquifer at Picatinny Arsenal, NJ, has been studied through a series of laboratory and field experiments. In the laboratory, batch and column experiments were conducted to quantify the rate and amount of Triton X-100 sorption to the aquifer sediments. In the field, a 400 mg/L aqueous Triton X-100 solution was injected into the aquifer at a rate of 26.5 L/min for a 35-d period. The transport of Triton X-100 was monitored by sampling and analysis of groundwater at six locations surrounding the injection well. Equilibrium batch sorption experiments showed that Triton X-100 sorbs strongly and nonlinearly to the field soil with the sharpest inflection point of the isotherm occurring at an equilibrium aqueous Triton X-100 concentration close to critical micelle concentration. Batch, soil column, and field experimental data were analyzed with zero-, one-, and two- dimensional (respectively) transient solute transport models with either equilibrium or rate-limited sorption. These analyses reveal that Triton X- 100 sorption to the aquifer solids is slow relative to advective and dispersive transport and that an equilibrium sorption model cannot simulate accurately the observed soil column and field data. Comparison of kinetic sorption parameters from batch, column, and field transport data indicate that both physical heterogeneities and Triton X-100 mass transfer between water and soil contribute to the kinetic transport effects.Transport of a nonionic surfactant (Triton X-100) at aqueous concentrations less than 400 mg/L through a trichloroethene-contaminated sand-and-gravel aquifer was studied. Equilibrium batch sorption experiments showed that Triton X-100 sorbs strongly and nonlinearly to the field soil with the sharpest inflection point of the isotherm occurring at an equilibrium aqueous Triton X-100 concentration close to

  3. Thermodynamics of non-ionic surfactant Triton X-100-cationic surfactants mixtures at the cloud point

    International Nuclear Information System (INIS)

    Batigoec, Cigdem; Akbas, Halide; Boz, Mesut

    2011-01-01

    Highlights: → Non-ionic surfactants are used as emulsifier and solubilizate in such as textile, detergent and cosmetic. → Non-ionic surfactants occur phase separation at temperature as named the cloud point in solution. → Dimeric surfactants have attracted increasing attention due to their superior surface activity. → The positive values of ΔG cp 0 indicate that the process proceeds nonspontaneous. - Abstract: This study investigates the effects of gemini and conventional cationic surfactants on the cloud point (CP) of the non-ionic surfactant Triton X-100 (TX-100) in aqueous solutions. Instead of visual observation, a spectrophotometer was used for measurement of the cloud point temperatures. The thermodynamic parameters of these mixtures were calculated at different cationic surfactant concentrations. The gemini surfactants of the alkanediyl-α-ω-bis (alkyldimethylammonium) dibromide type, on the one hand, with different alkyl groups containing m carbon atoms and an ethanediyl spacer, referred to as 'm-2-m' (m = 10, 12, and 16) and, on the other hand, with -C 16 alkyl groups and different spacers containing s carbon atoms, referred to as '16-s-16' (s = 6 and 10) were synthesized, purified and characterized. Additions of the cationic surfactants to the TX-100 solution increased the cloud point temperature of the TX-100 solution. It was accepted that the solubility of non-ionic surfactant containing polyoxyethylene (POE) hydrophilic chain was a maximum at the cloud point so that the thermodynamic parameters were calculated at this temperature. The results showed that the standard Gibbs free energy (ΔG cp 0 ), the enthalpy (ΔH cp 0 ) and the entropy (ΔS cp 0 ) of the clouding phenomenon were found positive in all cases. The standard free energy (ΔG cp 0 ) increased with increasing hydrophobic alkyl chain for both gemini and conventional cationic surfactants; however, it decreased with increasing surfactant concentration.

  4. Chemiluminescence determination of surfactant Triton X-100 in environmental water with luminol-hydrogen peroxide system

    Directory of Open Access Journals (Sweden)

    Qiu Chaokun

    2009-07-01

    Full Text Available Abstract Background The rapid, simple determination of surfactants in environmental samples is essential because of the extensive use and its potential as contaminants. We describe a simple, rapid chemiluminescence method for the direct determination of the non-ionic surfactant Triton X-100 (polyethylene glycol tert-octylphenyl ether in environmental water samples. The optimized experimental conditions were selected, and the mechanism of the Luminol-H2O2-Triton X-100 chemiluminesence system was also studied. Results The novel chemiluminescence method for the determination of non-ionic surfactant Triton X-100 was based on the phenomenon that Triton X-100 greatly enhanced the CL signal of the luminol-H2O2 system. The alkaline medium of luminol and the pH value obviously affected the results. Luminol concentration and hydrogen peroxide concentration also affected the results. The optimal conditions were: Na2CO3 being the medium, pH value 12.5, luminol concentration 1.0 × 10-4 mol L-1, H2O2 concentration 0.4 mol L-1. The possible mechanism was studied and proposed. Conclusion Under the optimal conditions, the standard curve was drawn up and quotas were evaluated. The linear range was 2 × 10-4 g·mL-1-4 × 10-2 g·mL-1 (w/v, and the detection limit was 3.97 × 10-5 g·mL-1 Triton X-100 (w/v. The relative standard deviation was less than 4.73% for 2 × 10-2 g·mL-1 (w/v Triton X-100 (n = 7. This method has been applied to the determination of Triton X-100 in environmental water samples. The desirable recovery ratio was between 96%–102% and the relative standard deviation was 2.5%–3.3%. The luminescence mechanism was also discussed in detail based on the fluorescence spectrum and the kinetic curve, and demonstrated that Triton X-100-luminol-H2O2 was a rapid reaction.

  5. Thermodynamics of non-ionic surfactant Triton X-100-cationic surfactants mixtures at the cloud point

    Energy Technology Data Exchange (ETDEWEB)

    Batigoec, Cigdem [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey); Akbas, Halide, E-mail: hakbas34@yahoo.com [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey); Boz, Mesut [Department of Chemistry, Faculty of Sciences, Trakya University, 22030 Edirne (Turkey)

    2011-12-15

    Highlights: > Non-ionic surfactants are used as emulsifier and solubilizate in such as textile, detergent and cosmetic. > Non-ionic surfactants occur phase separation at temperature as named the cloud point in solution. > Dimeric surfactants have attracted increasing attention due to their superior surface activity. > The positive values of {Delta}G{sub cp}{sup 0} indicate that the process proceeds nonspontaneous. - Abstract: This study investigates the effects of gemini and conventional cationic surfactants on the cloud point (CP) of the non-ionic surfactant Triton X-100 (TX-100) in aqueous solutions. Instead of visual observation, a spectrophotometer was used for measurement of the cloud point temperatures. The thermodynamic parameters of these mixtures were calculated at different cationic surfactant concentrations. The gemini surfactants of the alkanediyl-{alpha}-{omega}-bis (alkyldimethylammonium) dibromide type, on the one hand, with different alkyl groups containing m carbon atoms and an ethanediyl spacer, referred to as 'm-2-m' (m = 10, 12, and 16) and, on the other hand, with -C{sub 16} alkyl groups and different spacers containing s carbon atoms, referred to as '16-s-16' (s = 6 and 10) were synthesized, purified and characterized. Additions of the cationic surfactants to the TX-100 solution increased the cloud point temperature of the TX-100 solution. It was accepted that the solubility of non-ionic surfactant containing polyoxyethylene (POE) hydrophilic chain was a maximum at the cloud point so that the thermodynamic parameters were calculated at this temperature. The results showed that the standard Gibbs free energy ({Delta}G{sub cp}{sup 0}), the enthalpy ({Delta}H{sub cp}{sup 0}) and the entropy ({Delta}S{sub cp}{sup 0}) of the clouding phenomenon were found positive in all cases. The standard free energy ({Delta}G{sub cp}{sup 0}) increased with increasing hydrophobic alkyl chain for both gemini and conventional cationic

  6. Membrane-surfactant interactions. The role of surfactant in mitochondrial complex III-phospholipid-Triton X-100 mixed micelles

    International Nuclear Information System (INIS)

    Valpuesta, J.M.; Arrondo, J.L.; Barbero, M.C.; Pons, M.; Goni, F.M.

    1986-01-01

    Complex III (ubiquinol-cytochrome c reductase) was purified from beef heart mitochondria in the form of protein-phospholipid-Triton X-100 mixed micelles (about 1:80:100 molar ratio). Detergent may be totally removed by sucrose density gradient centrifugation, and the resulting lipoprotein complexes retain full enzyme activity. In order to understand the role of surfactant in the mixed micelles, and the interaction of Triton X-100 with integral membrane proteins and phospholipid bilayers, both the protein-lipid-surfactant mixed micelles and the detergent-free lipoprotein system were examined from the point of view of particle size and ultrastructure, enzyme activity, tryptophan fluorescence quenching, 31P NMR, and Fourier transform infrared spectroscopy. The NMR and IR spectroscopic studies show that surfactant withdrawal induces a profound change in phospholipid architecture, from a micellar to a lamellar-like phase. However, electron microscopic observations fail to reveal the existence of lipid bilayers in the absence of detergent. We suggest that, under these conditions, the lipid:protein molar ratio (80:1) is too low to permit the formation of lipid bilayer planes, but the relative orientation and mobility of phospholipids with respect to proteins is similar to that of the lamellar phase. Protein conformational changes are also detected as a consequence of surfactant removal. Fourier transform infrared spectroscopy indicates an increase of peptide beta-structure in the absence of Triton X-100; changes in the amide II/amide I intensity ratio are also detected, although the precise meaning of these observations is unclear

  7. Cloud Point Extraction of Toxic Reactive Black 5 Dye from Water Samples Using Triton X-100 as Nonionic Surfactant

    Directory of Open Access Journals (Sweden)

    Raziyeh Mousavi

    2011-01-01

    Full Text Available A surfactant mediated cloud point extraction (CPE procedure has been developed to remove color from wastewater containing reactive black 5, using triton x-100 (TX-100 as non-ionic surfactant. The effects of the concentration of the surfactant, pH, temperature and salt concentration on the different concentrations of dye have been studied and optimum conditions were obtained for the removal of reactive black 5 (RB 5. The concentration of RB 5 in the dilute phase was measured using UV-Vis spectrophotometer. It was found that the separation of phases was complete and the recovery of RB 5 was very effective in the presence of NaCl as an electrolyte. The results showed that up to 600 mg L-1 of RB 5 can quantitatively be removed (>97% by cloud point extraction procedure in a single extraction using optimum conditions.

  8. Cloud point extraction for the determination of heavy metals by nonionic surfactant Triton X-100 and PAN

    International Nuclear Information System (INIS)

    Cabrera Puig, I.; Perez Gramatges, A.

    2006-01-01

    A novel methodology for extraction and preconcentration of trace metals based on cloud point phenomenon was applied to the analysis of Co(II), Cu(II), Cd(II), Pb(II) y Ni(II) in a certified reference material (CRM), using Triton X-100 as nonionic surfactant, and AAS for the determination. Different parameters that can influence the extraction efficiency were studied, such as pH and ionic strength of the solution. The precision, accuracy and detection limits of the method were determined using a CRM from the Environmental Analysis Laboratory of InSTEC. We applied our methodology to the detection of the metals in naturals waters (Almendares river and tap water) . The data obtained presented in this work is part of the validation file of the proposed analytical procedure for the determination of heavy metals

  9. Conductometric study of sodium dodecyl sulfate - nonionic surfactant (Triton X-100, Tween 20, Tween 60, Tween 80 or Tween 85 mixed micelles in aqueous solution

    Directory of Open Access Journals (Sweden)

    Ćirin Dejan M.

    2012-01-01

    Full Text Available The present study is concerned with the determination of the critical micelle concentration (cmc of mixed micelles of sodium dodecyl sulfate with one of five nonionic surfactants (Triton X-100, Tween 20, Tween 60, Tween 80 or Tween 85 from conductance measurements. Based on the calculated values of the β parameters we have noticed that SDS-nonionic surfactants mostly showed strong synergistic effect. It was found that nonionic surfactants with mainly longer and more hydrophobic tail show stronger interactions with hydrophobic part of SDS, thus expressing stronger synergism. In SDS-Tween 80 binary system the strongest synergistic effect was noticed. SDS-Tween 85 micellar system showed antagonistic effect, most probably because the presence of the double bond in its three hydrophobic tails (three C18 tails makes it sterically rigid.

  10. The influence of Triton X-100 surfactant on the morphology and properties of zinc sulfide nanoparticles for applications in azo dyes degradation

    International Nuclear Information System (INIS)

    Dumbrava, Anca; Berger, Daniela; Prodan, Gabriel; Matei, Cristian; Moscalu, Florin; Diacon, Aurel

    2017-01-01

    Herein we report the synthesis, by two different routes, of ZnS nanoparticles capped with Triton X-100 (TX), which were characterized by X-ray diffraction, transmission electron microscopy, high resolution electron microscopy, selected area electron diffraction, energy dispersive X-ray spectroscopy, FTIR spectroscopy, UV–visible spectroscopy, photoluminescence spectroscopy, and surface area measurements. The TX-capped ZnS nanopowders have a very good photocatalytic activity and high specific surface area, depending on the synthesis route; e.g. an azo dye solution is almost complete photobleached in only 60 min (a photocatalytic activity of 97.79%) using TX-capped ZnS nanopowder, with specific surface area of 191 m 2 /g, and further a photocatalytic activity of 99.75% was achieved in 120 min. Based on the photocatalytic results, the ZnS nanopowders can be considered suitable catalysts for a green, very efficient and quick strategy for removing of organic pollutants from wastewaters. - Highlights: • Triton X-100 was used as surfactant in ZnS nanopowders synthesis by two methods. • Triton X-capped ZnS nanoparticles with high specific surface area were synthesized. • A very high capacity for bleaching an azo dye solution was evidenced. • Some of ZnS powders properties were crucially modified by the synthesis technique.

  11. The influence of Triton X-100 surfactant on the morphology and properties of zinc sulfide nanoparticles for applications in azo dyes degradation

    Energy Technology Data Exchange (ETDEWEB)

    Dumbrava, Anca, E-mail: adumbrava@univ-ovidius.ro [Department of Chemistry and Chemical Engineering, Ovidius University of Constanta, 124 Mamaia Blvd., Constanta 900527 (Romania); Berger, Daniela, E-mail: danaberger01@yahoo.com [University Politehnica of Bucharest, Department of Inorganic Chemistry, Physical Chemistry and Electrochemistry, Polizu Street 1-7, Bucharest 011061 (Romania); Prodan, Gabriel [Electron Microscopy Laboratory, Ovidius University of Constanta, 124 Mamaia Blvd., Constanta 900527 (Romania); Matei, Cristian [University Politehnica of Bucharest, Department of Inorganic Chemistry, Physical Chemistry and Electrochemistry, Polizu Street 1-7, Bucharest 011061 (Romania); Moscalu, Florin [Department of Physics, Ovidius University of Constanta, 124 Mamaia Blvd., Constanta 900527 (Romania); Diacon, Aurel [University Politehnica of Bucharest, Department of Bioresources and Polymer Science, Polizu Street 1-7, Bucharest 011061 (Romania)

    2017-06-01

    Herein we report the synthesis, by two different routes, of ZnS nanoparticles capped with Triton X-100 (TX), which were characterized by X-ray diffraction, transmission electron microscopy, high resolution electron microscopy, selected area electron diffraction, energy dispersive X-ray spectroscopy, FTIR spectroscopy, UV–visible spectroscopy, photoluminescence spectroscopy, and surface area measurements. The TX-capped ZnS nanopowders have a very good photocatalytic activity and high specific surface area, depending on the synthesis route; e.g. an azo dye solution is almost complete photobleached in only 60 min (a photocatalytic activity of 97.79%) using TX-capped ZnS nanopowder, with specific surface area of 191 m{sup 2}/g, and further a photocatalytic activity of 99.75% was achieved in 120 min. Based on the photocatalytic results, the ZnS nanopowders can be considered suitable catalysts for a green, very efficient and quick strategy for removing of organic pollutants from wastewaters. - Highlights: • Triton X-100 was used as surfactant in ZnS nanopowders synthesis by two methods. • Triton X-capped ZnS nanoparticles with high specific surface area were synthesized. • A very high capacity for bleaching an azo dye solution was evidenced. • Some of ZnS powders properties were crucially modified by the synthesis technique.

  12. Oxygen effect in the radiolysis of triton X-100 aqueous solution

    International Nuclear Information System (INIS)

    Perkowski, J.; Mayer, J.

    1994-01-01

    Experiments with Triton X-100 as a model surfactant were performed under steady-state conditions, using deoxygenated solutions as well as those saturated with N 2 O, O 2 or N 2 O/O 2 mixtures. The Triton x-100 decomposition yield was dependent on the O 2 content of the irradiated system. Oxygen promoted surfactant decomposition in aqueous solution containing only Triton X-100. (author) 13 refs.; 1 tab

  13. Binding Of Ferrocyphen By Sds, Ctab And Triton X-100 In Water ...

    African Journals Online (AJOL)

    SDS), cetyltrimethylammonium bromide (CTAB) and Triton X-100 surfactants was studied spectrophotometrically in water-ethanol medium. The equilibrium binding constant (Kb) and the number of binding sites (n) per surfactant monomer were ...

  14. Triton X-100 catalyzed synthesis of α-aminophosphonates

    Directory of Open Access Journals (Sweden)

    Nemallapudi Bakthavatchala Reddy

    2016-09-01

    Full Text Available Synthesis of α-aminophosphonates by a three-component condensation of an aldehyde, amines and dialkyl phosphites in the presence of a non-ionic surfactant Triton X-100 catalyst at 70 °C in aqueous medium is accomplished. The advantages are high yield, mild reaction conditions, simple work-up and eco-friendliness. All the newly-synthesized compounds (4a–j exhibited moderate in vitro antibacterial and antifungal activities.

  15. Radiation chemistry connection with the positronium formation in aqueous solution of triton X-100

    International Nuclear Information System (INIS)

    Das, S.K.; Ganguly, B.N.

    1996-01-01

    Positronium formation bears its connection to radiation chemical phenomenon. This has been demonstrated here to probe the micelle formation and further structural changes in Triton X-100 surfactant solution. (author). 6 refs., 3 figs

  16. Triton X-100 as a complete liquid scintillation cocktail for counting aqueous solutions and ionic nutrient salts

    International Nuclear Information System (INIS)

    Reed, D.W.

    1984-01-01

    Triton X-100, used alone, was found to act as a complete liquid scintillation cocktail. Triton X-100 acted as a scintillator and the effect was not due to Cerenkov radiation. A variety of other commercially available surfactants also acted as scintillators, but with different levels of efficiency. Triton X-100/water combinations were suitable for counting aqueous solutions of 33 P and 86 Rb and the count rate was stable over extended periods of time. Triton X-100/toluene combinations also yielded high counting efficiencies. Triton X-100 was more sensitive to quenching than standard cocktails containing fluors. (author)

  17. Role of triton X-100 and hydrothermal treatment on the morphological features of nanoporous hydroxyapatite nanorods

    Energy Technology Data Exchange (ETDEWEB)

    Iyyappan, E.; Wilson, P., E-mail: catwils@gmail.com; Sheela, K.; Ramya, R.

    2016-06-01

    Hydroxyapatite (HA) particles were synthesized using Ca(NO{sub 3}){sub 2}·4H{sub 2}O and (NH{sub 4}){sub 2}HPO{sub 4} as precursors with varying contents of non-ionic surfactant viz., triton X-100 (organic modifier) via co-precipitation method followed by hydrothermal treatment. The prepared HA particles have been characterized by X-ray diffraction (XRD), Fourier Transform Infrared spectroscopy (FT-IR), Energy Dispersive X-ray Analysis (EDX), High Resolution Scanning Electron Microscopy (HRSEM), High Resolution Transmission Electron Microscopy (HRTEM) and Nitrogen adsorption–desorption experiments. The XRD and FTIR studies indicate the formation of HA phase in all the synthesized samples. The specific roles of triton X-100 and hydrothermal treatment in dispersing and in directing the crystal growth respectively have been discussed by comparing the observations from individual experiments using triton X-100 and hydrothermal treatment with that of combined protocol involving both. The plausible mechanism for the individual roles of both triton X-100 and hydrothermal treatment have been proposed. - Highlights: • Nanoporous HA nanorods are synthesized via triton X-100 assisted hydrothermal treatment. • Triton X-100 hinder the agglomeration of HA primary particles • Hydrothermal treatment increase the aspect ratio of the HA particles • Oriented attachment of HA particles occurs under hydrothermal treatment facilitated by triton X-100 stabilized HA collides • The percentage of mesopore volume is higher for hydrothermally treated samples.

  18. Role of triton X-100 and hydrothermal treatment on the morphological features of nanoporous hydroxyapatite nanorods

    International Nuclear Information System (INIS)

    Iyyappan, E.; Wilson, P.; Sheela, K.; Ramya, R.

    2016-01-01

    Hydroxyapatite (HA) particles were synthesized using Ca(NO 3 ) 2 ·4H 2 O and (NH 4 ) 2 HPO 4 as precursors with varying contents of non-ionic surfactant viz., triton X-100 (organic modifier) via co-precipitation method followed by hydrothermal treatment. The prepared HA particles have been characterized by X-ray diffraction (XRD), Fourier Transform Infrared spectroscopy (FT-IR), Energy Dispersive X-ray Analysis (EDX), High Resolution Scanning Electron Microscopy (HRSEM), High Resolution Transmission Electron Microscopy (HRTEM) and Nitrogen adsorption–desorption experiments. The XRD and FTIR studies indicate the formation of HA phase in all the synthesized samples. The specific roles of triton X-100 and hydrothermal treatment in dispersing and in directing the crystal growth respectively have been discussed by comparing the observations from individual experiments using triton X-100 and hydrothermal treatment with that of combined protocol involving both. The plausible mechanism for the individual roles of both triton X-100 and hydrothermal treatment have been proposed. - Highlights: • Nanoporous HA nanorods are synthesized via triton X-100 assisted hydrothermal treatment. • Triton X-100 hinder the agglomeration of HA primary particles • Hydrothermal treatment increase the aspect ratio of the HA particles • Oriented attachment of HA particles occurs under hydrothermal treatment facilitated by triton X-100 stabilized HA collides • The percentage of mesopore volume is higher for hydrothermally treated samples

  19. SOME PHYSICOCHEMICAL PROPERTIES OF OCTYLPHENOL ETHOXYLATE NONIONICS (TRITON X-100, TRITON X-114 AND TRITON X-405 AND THE TEMPERATURE EFFECT ON THIS PROPERTIES

    Directory of Open Access Journals (Sweden)

    Taliha Sidim

    2016-11-01

    Full Text Available Surface tensions and condutvities of aqueous solutions of nonionic surfactants at various concentrations were measured at diffferent temperatures.The critical micelle concentration (CMC of aqueous solutions of three different octylphenol ethoxylate nonionics(Triton X-114, Triton X-100 and Triton X-405 are determined at different temperatures.The effect of the ethylene oxide chain length and temperature on the CMC is also determined.

  20. Fluorometric sensing of Triton X-100 based organized media in water by a MOF

    Energy Technology Data Exchange (ETDEWEB)

    Dey, Biswajit, E-mail: bdeychem@gmail.com [Department of Chemistry, Visva-Bharati University, Santiniketan 731235 (India); Mondal, Ranjan Kumar; Dhibar, Subhendu [Department of Chemistry, Visva-Bharati University, Santiniketan 731235 (India); Chattopadhyay, Asoke Prasun [Department of Chemistry, University of Kalyani, Kalyani 741235 (India); Bhattacharya, Subhash Chandra [Department of Chemistry, Jadavpur University, Kolkata 700032 (India)

    2016-04-15

    The fluorescent property of the aqueous solution of a metal organic framework (MOF) of Mn(II), having a sedimentary rocks like microstructure in solid-state, has been investigated. The luminescent feature of the the aqueous solution of MOF has been employed for studying the interactions of MOF with different surfactants including neutral, cationic, and anionic types in water medium. Interestingly, the MOF can very selective sense Triton X-100 based micelle in water medium. During the sensing process the fluorescent monomer of the MOF gets accommodated at the palisade layer of Triton X-100 in water medium and this has also been justified by simple fluorescence spectral and FE-SEM microstructural analysis. Thus, a MOF of Mn(II) can act as a selective fluorescent sensor for Triton X-100 based organized medium in water. - Highlights: • Microstructural and crystallographic studies of a water-soluble MOF are performed. • The luminescent property of MOF in water medium is explored. • The interaction between Triton X-100 and the MOF in water medium is studied by fluorometric and microstructural analysis. • The MOF acts as a selective fluorometric sensor for the Triton X-100 based organized media in water. • The monomer of MOF presents in the Triton X-100 micelle in water.

  1. Fluorometric sensing of Triton X-100 based organized media in water by a MOF

    International Nuclear Information System (INIS)

    Dey, Biswajit; Mondal, Ranjan Kumar; Dhibar, Subhendu; Chattopadhyay, Asoke Prasun; Bhattacharya, Subhash Chandra

    2016-01-01

    The fluorescent property of the aqueous solution of a metal organic framework (MOF) of Mn(II), having a sedimentary rocks like microstructure in solid-state, has been investigated. The luminescent feature of the the aqueous solution of MOF has been employed for studying the interactions of MOF with different surfactants including neutral, cationic, and anionic types in water medium. Interestingly, the MOF can very selective sense Triton X-100 based micelle in water medium. During the sensing process the fluorescent monomer of the MOF gets accommodated at the palisade layer of Triton X-100 in water medium and this has also been justified by simple fluorescence spectral and FE-SEM microstructural analysis. Thus, a MOF of Mn(II) can act as a selective fluorescent sensor for Triton X-100 based organized medium in water. - Highlights: • Microstructural and crystallographic studies of a water-soluble MOF are performed. • The luminescent property of MOF in water medium is explored. • The interaction between Triton X-100 and the MOF in water medium is studied by fluorometric and microstructural analysis. • The MOF acts as a selective fluorometric sensor for the Triton X-100 based organized media in water. • The monomer of MOF presents in the Triton X-100 micelle in water.

  2. APPLICATION OF TRITON X-100 COATED POLY VINYL ...

    African Journals Online (AJOL)

    Preferred Customer

    including sodium dodecyl sulfate (SDS), Triton X-100, cetyltrimethylammonium bromide. (CTAB) and n-dodecytrimethylammonium bromide (DTAB) with the purity of analytical grade was purchased from E. Merck, Darmstadt, Germany and were used as received. Doubly distilled deionized water was used throughout.

  3. Pulse radiolysis of Triton X-100 aqueous solution

    International Nuclear Information System (INIS)

    Perkowski, J.; Mayer, J.

    1990-01-01

    Pulse radiolysis of deaerated aqueous solutions of 4 · 10 -5 -2.4 · 10 -3 mol · dm -3 Triton X-100 gives rise to a transient species originating from the reactions of OH radicals and H atoms. The rate constants of these reactions were found to be 8.8 · 10 9 mol -1 · dm 3 · s -1 and 1.25 · 10 9 mol -1 · dm 3 · s -1 , respectively, for Triton X-100 concentrations below CMC. The corresponding transient species were found to decay according to second order kinetics. The mechanism of the reactions, including concentration effects is discussed. (author) 18 refs.; 3 figs

  4. Sorption of Triton X-100 on soil organic matter fractions: kinetics and isotherms.

    Science.gov (United States)

    Zhang, Guangzhi; Hu, Hao; Sun, Weiling; Ni, Jinren

    2009-01-01

    Kinetics and isotherms of Triton X-100 sorption on soil, base-extracted soil (BE), humic acid (HA) and humin (HM) were investigated respectively to get better understanding on characteristics of the surfactant sorption onto different soil organic matters (SOMs). It was demonstrated that the kinetics results could be satisfactorily described by the pseudo-second order model. The half of the time to reach equilibrium (t1/2) for different sorbents followed the sequence of soil > HA > BE > HM. Furthermore, the calculated equilibrium sorption capacity (C(eq)) was found in the sequence of HA > BE > HM > soil, which agreed well with the experimental results. The isotherms of Triton X-100 sorption on soil and HA could be well described by the S-type isotherm, but BE and HM by the L-type. The isotherms of all the four sorbents were found reasonably fitted to the Langmuir equation. The K(d) value, defined as the ratio of Triton X-100 in sorbent and in the equilibrium solution for given concentrations, generally followed the order of HM > HA > soil > BE. Separated HM and HA showed high affinity for Triton X-100, but the HA and HM in soil and BE were tightly bounded by the minerals. Thus, the HA on the soil surface might dominate the sorption, whereas the bounded HM would play a key role upon the surfactants being penetrated inside the soil.

  5. Use of resistant mutants to study the interaction of triton X-100 with Staphylococcus aureus.

    OpenAIRE

    Raychaudhuri, D; Chatterjee, A N

    1985-01-01

    Staphylococcus aureus mutants resistant to the nonionic detergent Triton X-100, isolated from the wild-type strain H and the autolysin-deficient strain RUS3, could grow and divide in broth containing 5% (vol/vol) Triton X-100, while growth of the parental strains was markedly inhibited above the critical micellar concentration (0.02%) of the detergent. Growth-inhibitory concentrations of Triton X-100 killed wild-type cells without demonstrable cellular lysis. Triton X-100 stimulated autolysin...

  6. Bioavailability of hydrocarbons to bacterial consortia during Triton X-100 mediated biodegradation in aqueous media.

    Science.gov (United States)

    Pęziak, Daria; Piotrowska, Aleksandra; Marecik, Roman; Lisiecki, Piotr; Woźniak, Marta; Szulc, Alicja; Ławniczak, Łukasz; Chrzanowski, Łukasz

    2013-01-01

    The aim of our study was to investigate the effect of Triton X-100 on the biodegradation efficiency of hexadecane and phenanthrene carried out by two bacterial consortia. It was established that the tested consortia were not able to directly uptake compounds closed in micelles. It was observed that in micellar systems the nonionic synthetic surfactant was preferentially degraded (the degradation efficiency of Triton X-100 after 21 days was 70% of the initial concentration - 500 mg/l), followed by a lesser decomposition of hydrocarbon released from the micelles (30% for hexadecane and 20% for phenanthrene). However, when hydrocarbons were used as the sole carbon source, 70% of hexadecane and 30% of phenanthrene were degraded. The degradation of the surfactant did not contribute to notable shifts in bacterial community dynamics, as determined by Real-Time PCR. The obtained results suggest that if surfactant-supplementation is to be used as an integral part of a bioremediation process, then possible bioavailability decrease due to entrapment of the contaminant into surfactant micelles should also be taken into consideration, as this phenomenon may have a negative impact on the biodegradation efficiency. Surfactant-induced mobilization of otherwise recalcitrant hydrocarbons may contribute to the spreading of contaminants in the environment and prevent their biodegradation.

  7. Interactions between selected bile salts and Triton X-100 or sodium lauryl ether sulfate

    Directory of Open Access Journals (Sweden)

    Ćirin Dejan M

    2011-12-01

    Full Text Available Abstract Background In order to develop colloidal drug carriers with desired properties, it is important to determine physico-chemical characteristics of these systems. Bile salt mixed micelles are extensively studied as novel drug delivery systems. The objective of the present investigation is to develop and characterize mixed micelles of nonionic (Triton X-100 or anionic (sodium lauryl ether sulfate surfactant having oxyethylene groups in the polar head and following bile salts: cholate, deoxycholate and 7-oxodeoxycholate. Results The micellization behaviour of binary anionic-nonionic and anionic-anionic surfactant mixtures was investigated by conductivity and surface tension measurements. The results of the study have been analyzed using Clint's, Rubingh's, and Motomura's theories for mixed binary systems. The negative values of the interaction parameter indicate synergism between micelle building units. It was noticed that Triton X-100 and sodium lauryl ether sulfate generate the weakest synergistic interactions with sodium deoxycholate, while 7-oxodeoxycholate creates the strongest attractive interaction with investigated co-surfactants. Conclusion It was concluded that increased synergistic interactions can be attributed to the larger number of hydrophilic groups at α side of the bile salts. Additionally, 7-oxo group of 7-oxodeoxycholate enhance attractive interactions with selected co-surfactants more than 7-hydroxyl group of sodium cholate.

  8. Kinetics of solubilization with Triton X-100 of egg-yolk lecithin bilayers containing cholesterol

    OpenAIRE

    Hobai, Stefan

    2001-01-01

    The titration solubilization of multilamellar egg-yolk lecithin liposomes (MLV-EYL) with Triton X-100 was studied by rectangular optical diffusimetric measurements as a function of cholesterol (Chol) concentration. It was determinated the variation of optic percentage diffu-sion (per mmol surfactant), DDif%/mmol TX-100, in the course of solubilization of MLV-EYL-Chol system with TX-100 10mM. The statistical analysis of the titration curves can reveal the contribution of cholesterol to the sta...

  9. Removal of Bound Triton X-100 from Purified Bovine Heart Cytochrome bc1

    OpenAIRE

    Varhač, Rastislav; Robinson, Neal C.; Musatov, Andrej

    2009-01-01

    Cytochrome bc1 isolated from Triton X-100 solubilized mitochondrial membranes contains up to 120 nmol of Triton X-100 bound per nmol of the enzyme. Purified cytochrome bc1 is fully active; however, protein bound Triton X-100 significantly interferes with structural studies of the enzyme. Removal of Triton X-100 bound to bovine cytochrome bc1 was accomplished by incubation with Bio-Beads SM-2 in presence of sodium cholate. Sodium cholate is critical since it does not interfere with the adsorpt...

  10. Non-immunological precipitation by the neutral detergent triton X-100 in agar gel diffusion.

    OpenAIRE

    Mansheim, B J; Stenstrom, M L

    1980-01-01

    Triton X-100 can be used to clarify vague immunoprecipitin lines from bacterial antigens; however, non-immunological precipitation can lead to mistaken interpretation of immunodiffusion results. If Triton X-100 is added directly to the gel during preparation rather than to the antigen well, this detergent artifact can be eliminated.

  11. Interactions of dipeptides with Triton X-100 in aqueous solution: A volumetric and spectroscopic study

    International Nuclear Information System (INIS)

    Yan, Zhenning; Wu, Shuangyan; Pan, Qi; Geng, Rui; Gu, Bixin; Wang, Jianji

    2014-01-01

    Highlights: • The values of V 2,ϕ o and Δ t V° are positive. • Interactions of Triton X-100 with charged and polar groups of dipeptides dominate. • Addition of dipeptide in water decreases the c cmc and the aggregation number of Triton X-100. • The affinity between dipeptide and Triton X-100 micelle increases with the increase in the length of alkyl chain of peptides. • Triton X-100 interacts with dipeptides more weakly than SDS. -- Abstract: The interactions of dipeptides with Triton X-100 in aqueous solution have been investigated by means of density, fluorescence spectroscopy and UV–vis spectroscopy. The standard partial molar volume (V 2,ϕ o ), standard partial molar volume of transfer for dipeptide from water to aqueous Triton X-100 solution (Δ t V o ) and partial molar expansibility (E ϕ o ) have been calculated from density data. Fluorescence spectroscopy was used to estimate the critical micellar concentration (c cmc ) and micelle aggregation number of Triton X-100 in aqueous dipeptide solutions. Effects of temperature and hydrocarbon chain length of dipeptides on the volumetric properties of dipeptide and critical micelle concentration (c cmc ) of Triton X-100 were examined. The pyrene fluorescence spectra were also used to study the change of micropolarity produced by the interactions of Triton X-100 with dipeptides. From the results of UV–vis absorption spectra, the binding constant between dipeptide and Triton X-100 above the c cmc was determined. The results have been interpreted in terms of solute–solvent interactions and structural changes in the mixed solutions

  12. Crude soybean hull peroxidase treatment of phenol in synthetic and real wastewater: enzyme economy enhanced by Triton X-100.

    Science.gov (United States)

    Steevensz, Aaron; Madur, Sneha; Feng, Wei; Taylor, Keith E; Bewtra, Jatinder K; Biswas, Nihar

    2014-02-05

    Soybean peroxidase (SBP)-catalyzed removal of phenol from wastewater has been demonstrated as a feasible wastewater treatment strategy and a non-ionic surfactant, Triton X-100, has the potential for increasing the enzyme economy of the process. Systematic studies on the enzyme-surfactant system have been lacking as well as demonstration of its applicability to industrial wastewater. This paper addresses those two gaps, the latter based on real wastewater from alkyd resin manufacture. The minimum effective Triton X-100 concentrations for crude SBP-catalyzed phenol conversion (≥95%) over 1-10 mM showed a linear trend. To illustrate translation of such lab results to real-world samples, this data were used to optimize crude SBP needed for phenol conversion over that concentration range. Triton X-100 increases enzyme economy by 10- to 13-fold. This treatment protocol was directly applied to tote-scale (700-1000 L) treatment of alkyd resin wastewater, with phenol ranging from 7 to 28 mM and total organic carbon content of >40 g/L, using a crude SBP extract derived from dry soybean hulls by simple aqueous elution. This extract can be used to remove phenol from a complex industrial wastewater and the process is markedly more efficient in the presence of Triton X-100. The water is thus rendered amenable to conventional biological treatment whilst the hulls could still be used in feed, thus adding further value to the crop. Copyright © 2013 Elsevier Inc. All rights reserved.

  13. Heat transfer in nucleate pool boiling of aqueous SDS and triton X-100 solutions

    Energy Technology Data Exchange (ETDEWEB)

    Wasekar, Vivek M. [Tata Steel Limited, Department of Research and Development, Jamshedpur (India)

    2009-09-15

    Variation in degree of surface wettability is presented through the application of Cooper's correlative approach (h{proportional_to}M{sup -0.5}q{sub w}''0.67) for computing enhancement ({phi}) in nucleate pool boiling of aqueous solutions of SDS and Triton X-100 and its presentation with Marangoni parameter ({chi}) that represents the dynamic convection effects due to surface tension gradients. Dynamic spreading coefficient defined as {sigma} {sub dyn}N{sub a}, which relates spreading and wetting characteristics with the active nucleation site density on the heated surface and bubble evolution process, represents cavity filling and activation process and eliminates the concentration dependence of nucleate pool boiling heat transfer in boiling of aqueous surfactant solutions. Using the dynamic spreading coefficient ({sigma}{sub dyn}N{sub a}=0.09q{sub w}''0.71), correlation predictions within {+-}15% for both SDS and triton X-100 solutions for low heat flux boiling condition (q{sub w}''{<=} 100 kW/m {sup 2}) characterised primarily by isolated bubble regime are presented. (orig.)

  14. Photochemical assessment of UO2+2 complexation in Triton X-100 micellar system

    International Nuclear Information System (INIS)

    Das, S.K.; Ganguly, B.N.

    1994-01-01

    This is a report on the spectral characteristics of UO 2 +2 in the excited state in the Triton X-100 micellar medium. The downward curving of the Stern-Volmer plot explains the two kinds of populations of UO 2 +2 upon micellization. A blue shift of the quenched emission is ascribed due to the collisional encounter of UO 2 +2 with the head groups of Triton X-100. (author). 5 refs., 2 figs

  15. Association of nerve growth factor receptors with the triton X-100 cytoskeleton of PC12 cells

    International Nuclear Information System (INIS)

    Vale, R.D.; Ignatius, M.J.; Shooter, E.M.

    1985-01-01

    Triton X-100 solubilizes membranes of PC12 cells and leaves behind a nucleus and an array of cytoskeletal filaments. Nerve growth factor (NGF) receptors are associated with this Triton X-100-insoluble residue. Two classes of NGF receptors are found on PC12 cells which display rapid and slow dissociating kinetics. Although rapidly dissociating binding is predominant (greater than 75%) in intact cells, the majority of binding to the Triton X-100 cytoskeleton is slowly dissociating (greater than 75%). Rapidly dissociating NGF binding on intact cells can be converted to a slowly dissociating form by the plant lectin wheat germ agglutinin (WGA). This lectin also increases the number of receptors which associate with the Triton X-100 cytoskeleton by more than 10-fold. 125 I-NGF bound to receptors can be visualized by light microscopy autoradiography in Triton X-100-insoluble residues of cell bodies, as well as growth cones and neurites. The WGA-induced association with the cytoskeleton, however, is not specific for the NGF receptor. Concentrations of WGA which change the Triton X-100 solubility of membrane glycoproteins are similar to those required to alter the kinetic state of the NGF receptor. Both events may be related to the crossbridging of cell surface proteins induced by this multivalent lectin

  16. Resistance of human erythrocyte membranes to Triton X-100 and C12E8.

    Science.gov (United States)

    Crepaldi Domingues, Cleyton; Ciana, Annarita; Buttafava, Armando; Balduini, Cesare; de Paula, Eneida; Minetti, Giampaolo

    2009-01-01

    Lipid rafts are microdomains enriched in cholesterol and sphingolipids that contain specific membrane proteins. The resistance of domains to extraction by nonionic detergents at 4 degrees C is the commonly used method to characterize these structures that are operationally defined as detergent-resistant membranes (DRMs). Because the selectivity of different detergents in defining membrane rafts has been questioned, we have compared DRMs from human erythrocytes prepared with two detergents: Triton X-100 and C12E8. The DRMs obtained presented a cholesterol/protein mass ratio three times higher than in the whole membrane. Flotillin-2 was revealed in trace amounts in DRMs obtained with C12E8, but it was almost completely confined within the DRM fraction with Triton X-100. Differently, stomatin was found distributed in DRM and non-DRM fractions for both detergents. We have also measured the order parameter (S) of nitroxide spin labels inserted into DRMs by means of electron paramagnetic resonance. The 5- and 16-stearic acid spin label revealed significantly higher S values for DRMs obtained with either Triton X-100 or C12E8 in comparison to intact cells, while the difference in the S values between Triton X-100 and C12E8 DRMs was not statistically significant. Our results suggest that although the acyl chain packing is similar in DRMs prepared with either Triton X-100 or C12E8 detergent, protein content is dissimilar, with flotillin-2 being selectively enriched in Triton X-100 DRMs.

  17. A photochemical study of uranyl ion interaction with the Triton X-100 micellar system

    International Nuclear Information System (INIS)

    Das, S.K.; Ganguly, B.N.

    1996-01-01

    This is a report on the spectroscopic characteristics of UO 2 2+ in the excited state in Triton X-100 micellar medium. It also indicates some important results of viscosity and surface tension measurements of the system which have direct relevance to the spectroscopic investigation in the excited state. The quenching of the UO 2 2+ fluorescence due to Triton X-100, upon micellization in the aqueous medium, reveals two kinds of microenvironments of the fluorophore from the Stern-Volmer plot. This has been verified by flash photolytic measurements. A blue shift of the quenched emission spectrum is ascribed to the collisional encounter of UO 2 1 + with the head groups of Triton X-100

  18. Characterization of the Recombinant Thermostable Lipase (Pf2001 from Pyrococcus furiosus: Effects of Thioredoxin Fusion Tag and Triton X-100

    Directory of Open Access Journals (Sweden)

    Sylvia Maria Campbell Alquéres

    2011-01-01

    Full Text Available In this work, the lipase from Pyrococcus furiosus encoded by ORF PF2001 was expressed with a fusion protein (thioredoxin in Escherichia coli. The purified enzymes with the thioredoxin tag (TRX−PF2001Δ60 and without the thioredoxin tag (PF2001Δ60 were characterized, and various influences of Triton X-100 were determined. The optimal temperature for both enzymes was 80°C. Although the thioredoxin presence did not influence the optimum temperature, the TRX−PF2001Δ60 presented specific activity twice lower than the enzyme PF2001Δ60. The enzyme PF2001Δ60 was assayed using MUF-acetate, MUF-heptanoate, and MUF-palmitate. MUF-heptanoate was the preferred substrate of this enzyme. The chelators EDTA and EGTA increased the enzyme activity by 97 and 70%, respectively. The surfactant Triton X-100 reduced the enzyme activity by 50% and lowered the optimum temperature to 60°C. However, the thermostability of the enzyme PF2001Δ60 was enhanced with Triton X-100.

  19. EFFECT OF VITIS VINIFERA AGAINST TRITON X 100 INDUCED HYPERLIPIDAEMIA IN RATS

    OpenAIRE

    Masani YA; Mathew N; Chakraborty M; Kamath JV

    2012-01-01

    To evaluate the effect of Vitis vinfera fruit juice (VVFJ) against Triton X 100 induced hyperlipidaemia. Wister strain rats were treated with atorvastatin (ATOR-10mg/kg, p.o.), low and high dose of Vitis vinifera fruit juice (VVFJ- 100 and 500mg/kg) orally for 0, 24 and 44 hours after treated with Triton X 100 (400mg/kg, p.o). 4 hour after the last dose, blood was collected from all the animals and the separated serum was subjected for the estimation of serum lipoproteins level such as Trigly...

  20. Förster Resonance Energy Transfer (FRET) from Triton X-100 to 4-benzothiazol-2-yl-phenol: Varying FRET efficiency with CMC of the donor (Triton X-100)

    International Nuclear Information System (INIS)

    Paul, Bijan Kumar; Ganguly, Aniruddha; Karmakar, Saswati; Guchhait, Nikhil

    2013-01-01

    A heterocyclic compound viz., 4-benzothiazol-2-yl-phenol (4B2YP) has been synthesized and its photophysics have been examined through steady-state absorption, emission and time resolved emission spectroscopic techniques, in brief. Then 4B2YP has been exploited as an acceptor in the Förster Resonance Energy Transfer (FRET) process from photoexcited benzene aromatic nucleus of Triton X-100 (TX-100) surfactant. Dependence of the energy transfer efficiency on the donor concentration with respect to its critical micelle concentration (CMC) is clearly reflected in the study. High values of Stern–Volmer constant (K SV ) for quenching of the donor fluorescence in the presence of the acceptor suggest the operation of long-range dipole–dipole interaction in the course of energy transfer process, while the inference is aptly supported from time resolved fluorescence decay results. Experimental results show maximum FRET efficiency at the CMC of the donor (TX-100). -- Highlights: • FRET from neutral surfactant Triton X-100 to chromophore 4-benzothiazol-2-yl-phenol. • Steady state and time resolved spectroscopy. • Long-range dipole–dipole interaction responsible for FRET. • FRET efficiency as a measure of CMC of surfactant

  1. Förster Resonance Energy Transfer (FRET) from Triton X-100 to 4-benzothiazol-2-yl-phenol: Varying FRET efficiency with CMC of the donor (Triton X-100)

    Energy Technology Data Exchange (ETDEWEB)

    Paul, Bijan Kumar, E-mail: bijan.paul.chem.cu@gmail.com [Department of Chemistry, University of Calcutta, 92 A.P.C. Road, Calcutta 700009 (India); Ganguly, Aniruddha [Department of Chemistry, University of Calcutta, 92 A.P.C. Road, Calcutta 700009 (India); Karmakar, Saswati [Department of Chemistry, Sree Chaitanya College, Habra, North 24 Parganas (India); Guchhait, Nikhil, E-mail: nguchhait@yahoo.com [Department of Chemistry, University of Calcutta, 92 A.P.C. Road, Calcutta 700009 (India)

    2013-11-15

    A heterocyclic compound viz., 4-benzothiazol-2-yl-phenol (4B2YP) has been synthesized and its photophysics have been examined through steady-state absorption, emission and time resolved emission spectroscopic techniques, in brief. Then 4B2YP has been exploited as an acceptor in the Förster Resonance Energy Transfer (FRET) process from photoexcited benzene aromatic nucleus of Triton X-100 (TX-100) surfactant. Dependence of the energy transfer efficiency on the donor concentration with respect to its critical micelle concentration (CMC) is clearly reflected in the study. High values of Stern–Volmer constant (K{sub SV}) for quenching of the donor fluorescence in the presence of the acceptor suggest the operation of long-range dipole–dipole interaction in the course of energy transfer process, while the inference is aptly supported from time resolved fluorescence decay results. Experimental results show maximum FRET efficiency at the CMC of the donor (TX-100). -- Highlights: • FRET from neutral surfactant Triton X-100 to chromophore 4-benzothiazol-2-yl-phenol. • Steady state and time resolved spectroscopy. • Long-range dipole–dipole interaction responsible for FRET. • FRET efficiency as a measure of CMC of surfactant.

  2. A small-angle neutron scattering study of the structure of graphitized carbon black aggregates in Triton X-100/water solutions

    DEFF Research Database (Denmark)

    Garamus, V.M.; Pedersen, J.S.

    1998-01-01

    The structure of graphitized carbon black (CB) aggregates dispersed in water solutions with a non-ionic surfactant are studied by small-angle neutron scattering using contrast variation by heavy/light water mixing. The addition of CB to Triton X-100/water mixtures shifts the critical micelle...

  3. Tuning intermicellar potential of Triton X-100– anthranilic acid mixed ...

    Indian Academy of Sciences (India)

    Structural parameters of micelles formed by Triton X-100 in the presence of solubilized anthranilic acid at different pH values was investigated using light scattering and small angle neutron scattering. Analysis of the SANS data indicate that micelles are oblate ellipsoidal in nature with little variation in the dimensions, in the ...

  4. Tuning intermicellar potential of Triton X-100– anthranilic acid mixed ...

    Indian Academy of Sciences (India)

    the attractive interaction between the micelles diminishes. The interaction potential between Triton X-100 micelles can be thought of as the sum of the attractive van der Walls interaction and Coulombic repulsion due to charged anthranilic molecules on the surface of the micelles. Assuming a Yukawa form of the potential for ...

  5. Energy transfer in triton-X 100 micelles: a fluorescence study

    Science.gov (United States)

    Saha, D. C.; Ray, K.; Misra, T. N.

    2000-03-01

    The study of fluorescence energy transfer from the phenyl groups of the micellar triton X-100 (TX-100) to solubilised 1-pyrene butyric acid (PBA) has been carried out. Through the analysis of the donor fluorescence quenching energy transfer efficiency has been determined. The observed donor-acceptor separation suggests that pyrene molecules are distributed uniformly in the micellar core.

  6. Solvation dynamics in triton-X-100 and triton-X-165 micelles: Effect of micellar size and hydration

    Science.gov (United States)

    Kumbhakar, Manoj; Nath, Sukhendu; Mukherjee, Tulsi; Pal, Haridas

    2004-09-01

    Dynamic Stokes' shift measurements using coumarin 153 as the fluorescence probe have been carried out to study solvation dynamics in two nonionic micelles, viz., triton-X-100 (TX-100) and triton-X-165 (TX-165). In both the micelles, the solvent relaxation dynamics is biexponential in nature. While the fast solvation time τs1 is seen to be almost similar for both the micelles, the slow solvation time τs2 is found to be appreciably smaller in TX-165 than in TX-100 micelle. Dynamic light scattering measurements indicate that the TX-165 micelles are substantially smaller in size than that of TX-100. Assuming similar core size for both the micelles, as expected from the similar chemical structures of the nonpolar ends for both the surfactants, the Palisade layer is also indicated to be substantially thinner for TX-165 micelles than that of TX-100. The aggregation number of TX-165 micelles is also found to be substantially smaller than that of TX-100 micelles. Fluorescence spectral studies of C153 dye in the two micelles indicate that the Palisade layer of TX-165 micelles is more polar than that of TX-100 micelles. Fluorescence anisotropy measurements indicate that the microviscosity in the Palisade layer of TX-165 micelles is also lower than that of TX-100 micelles. Based on these results it is inferred that the structure of the Palisade layer of TX-165 micelles is quite loose and have higher degree hydration in comparison to that of TX-100 micelles. Due to these structural differences in the Palisade layers of TX-165 and TX-100 micelles the solvation dynamics is faster in the former micelles than in the latter. It has been further inferred that in the present systems the collective response of the water molecules at somewhat away from the probes is responsible for the faster component of the solvation time, which does not reflect much of the structural changes of the micellar Palisade layer. On the contrary, the slower solvation time component, which is mainly due to

  7. Permeabilization and lysis of Pseudomonas pseudoalcaligenes cells by triton X-100 for efficient production of D-malate

    NARCIS (Netherlands)

    Werf, M.J. van der; Hartmans, S.; Tweel, W.J.J. van den

    1995-01-01

    Pseudomonas pseudoalcaligenes can only form d-malate from maleate after incubation of the cells with a solvent or a detergent. The effect of the detergent Triton X-100 on d-malate production was studied in more detail. The longer the cells were incubated with Triton X-100, the higher was the

  8. Adsorption of triton X100 and potassium hydrogen phthalate on granular activated carbon from date pits

    Energy Technology Data Exchange (ETDEWEB)

    Merzougui, Z.; Nedjah, S.; Azoudj, Y.; Addoun, F. [Laboratoire d' etude physic-chimique des materiaux et application a l' environnement, Faculte de Chimie, USTHB (Algeria)], E-mail: zmerzougi@yahoo.fr

    2011-07-01

    Activated carbons, thanks to their versatility, are being used in the water treatment sector to absorb pollutants. Several factors influence the adsorption capacity of activated carbon and the aim of this study was to assess the effects of the porous texture and chemical nature of activated carbons on the adsorption of triton X100 and potassium hydrogen phthalate. Activated carbons used in this study were prepared from date pits with ZnCl2, KOH and H3PO4 by carbonization without adjuvant and adsorption of triton X100 and potassium hydrogen phthalate was conducted at 298K. Results showed that activated carbons prepared from date pits have a great potential for removing organic and inorganic pollutants from water and that the adsorption potential depends on the degree of activation of the activated carbons and on the compounds to absorb. This study highlighted that an increase of the carbon surface area and porosity results in a better adsorption capacity.

  9. Synthesis and characterization of novel N-substituted poly aniline by Triton X-100

    International Nuclear Information System (INIS)

    Arsalani, N.; Khavei, M.; Entezami, A. A.

    2003-01-01

    A new N-substituted poly aniline is synthesized by insertion of polyether chain in the form of Triton X-100 onto the poly aniline backbone. In the preparation method, firstly the emeraldine base poly aniline was reacted with Na H to produce the N-anionic doped poly aniline and then contacted with chlorinated Triton X-100. The prepared N-substituted poly aniline was characterized by UV-vis, FTIR, 1 H NMR spectroscopy techniques and elemental analysis. The physical properties of synthesized polymer such as electrical conductivity, thermal and electro activity properties were also studied. The prepared polymer has good solubility in common organic solvents such as T HF and chloroform

  10. Positronium reactions in the Triton X-100-p-nitro phenol system

    International Nuclear Information System (INIS)

    Kumar Das, S.; Nandi Ganguly, B.

    1997-01-01

    The positronium reactions have been used as a probe to study the solubilization of p-nitro phenol within the micellar phase of a Triton X-100 solution and the corresponding changes in the molecular association phenomenon. The presence of p-nitro phenol resulted in an enhancement of micellization which has been corroborated by surface tension measurements. This paper also lays emphasis on the secondary aggregation phenomenon of Triton X-100 molecules at the far post-micellar stage (∼ 10-15 mM). The solubilization of p-nitro phenol at various stages of aggregation has been discussed through the interaction with positronium atoms by setting up a kinetic model and reaction equilibria. (author)

  11. Radiolytic syntheses of hollow UO2 nanospheres in Triton X-100-based lyotropic liquid crystals

    International Nuclear Information System (INIS)

    Wang, Yongming; Chen, Qingde; Shen, Xinghai

    2017-01-01

    Hollow nanospheres (φ: 60-80 nm, wall thickness: 10-20 nm), consisted of UO 2 nanoparticles (φ: 3-5 nm), were successfully prepared in a Triton X-100-water (50:50, w/w) hexagonal lyotropic liquid crystal (LLC) by γ-irradiation, where water soluble ammonium uranyl tricarbonate was added as precursor. The product was stable at least up to 300 C. Furthermore, whether the nanospheres were hollow or not, and the wall thickness of the hollow nanospheres could be easily controlled via adjusting dose rate. While in the Triton X-100 based micellar systems, only solid nanospheres were obtained. At last, a possible combination mechanism containing adsorption, aggregation and fracturing processes was proposed.

  12. Micelle size modulation and phase behavior in MEGA-10/Triton X-100 mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Naous, M., E-mail: elzahraadz@yahoo.fr; Molina-Bolívar, J.A.; Ruiz, C. Carnero, E-mail: ccarnero@uma.es

    2014-12-20

    Highlights: • The size of micelles was studied as a function of the micellar composition, NaCl addition and temperature. • Cloud point can be modulated by changing both micellar composition and NaCl addition. • The energetic quantities at the cloud point were evaluated and discussed. - Abstract: This paper reports the effect of temperature and NaCl addition on micelle size and phase behavior in mixtures of N-decanoyl-N-methylglucamide (MEGA-10) and p-tert-octyl-phenoxy polyethylene (9.5) ether (Triton X-100 or TX100). The size of mixed micelles, as determined by dynamic light scattering (DLS), was found to increase with temperature but to be less pronounced at higher proportions of MEGA-10 in the solution. The cloud point was found to increase with an initial increase in the percentage of sugar-based surfactant in the mixture. This phase separation was sensitive to the presence of NaCl in the micellar solution, which induced a cloud point depression, thereby suggesting that the presence of electrolyte produces a marked alteration of the hydration layer of micelles. A thermodynamic analysis was performed assuming the clouding phenomenon to be a liquid–liquid phase-separation process. The resulting ΔG{sub CP}{sup 0} values were positive for all solutions. The cloud point process was exothermic in nature for the mixed micellar system, as proven by the negative value of ΔH{sub CP}{sup 0}. The process was more exothermic as the proportion of sugar-based surfactant in the mixed micelle increased (with and without NaCl in the solution). Furthermore, the negative values of ΔS{sub CP}{sup 0} indicate that the association of micelles in the clouding phenomenon is entropically unfavorable. It was observed from the enthalpy–temperature plots that the change in heat capacity is negative, thus indicating the important role played by dehydration in this thermodynamic process. This study found that the enthalpy–entropy compensation relationship holds for this

  13. Triton X-100 inhibits agonist-induced currents and suppresses benzodiazepine modulation of GABA(A) receptors in Xenopus oocytes

    DEFF Research Database (Denmark)

    Søgaard, Rikke; Ebert, Bjarke; Klaerke, Dan

    2009-01-01

    Changes in lipid bilayer elastic properties have been proposed to underlie the modulation of voltage-gated Na(+) and L-type Ca(2+) channels and GABA(A) receptors by amphiphiles. The amphiphile Triton X-100 increases the elasticity of lipid bilayers at micromolar concentrations, assessed from its...... effects on gramicidin channel A appearance rate and lifetime in artificial lipid bilayers. In the present study, the pharmacological action of Triton-X 100 on GABA(A) receptors expressed in Xenopus laevis oocytes was examined. Triton-X 100 inhibited GABA(A) alpha(1)beta(3)gamma(2S) receptor currents...... in a noncompetitive, time- and voltage-dependent manner and increased the apparent rate and extent of desensitization at 10 muM, which is 30 fold below the critical micelle concentration. In addition, Triton X-100 induced picrotoxin-sensitive GABA(A) receptor currents and suppressed allosteric modulation...

  14. Delivery of Optical Contrast Agents using Triton-X100, Part 1: Reversible permeabilization of live cells for intracellular labeling

    OpenAIRE

    van de Ven, Anne L; Adler-Storthz, Karen; Richards-Kortum, Rebecca

    2009-01-01

    Effective delivery of optical contrast agents into live cells remains a significant challenge. We sought to determine whether Triton-X100, a detergent commonly used for membrane isolation and protein purification, could be used to effectively and reversibly permeabilize live cells for delivery of targeted optical contrast agents. Although Triton-X100 is widely recognized as a good cell permeabilization agent, no systematic study has evaluated the efficiency, reproducibility, and reversibility...

  15. Effects of gamma radiation on phase behaviour and critical micelle concentration of Triton X-100 aqueous solutions

    International Nuclear Information System (INIS)

    Valdes Diaz, G.; Rodriguez-Calvo, S.; Perez-Gramatges, A.; Rapado-Paneque, M.; Fernandez-Lima, F. A.; Ponciano, C. R.; Silveira, E. F. . E-mail. apgram@instec.cu

    2007-01-01

    Ionising radiation used for sterilisation can have an effect on the physico-chemical properties of pharmaceutically relevant excipient systems, affecting therefore the stability of the formulation. The effect of gamma irradiation on the phase behaviour (cloud point - CP) and critical micelle concentration (CMC) of aqueous solutions of Triton X-100, used as a model nonionic surfactant, is investigated in this paper. Micellar solutions irradiated with ?-rays in a dose range between 0 and 70 kGy, including the sterilisation range of pharmaceutical preparations, were analysed using mass spectrometry. Results show a slight shift in molecular mass distribution of ethoxylated surfactant, which indicates degradation of polyethoxylated chains by water radical attacks. This fact, combined with the formation of cross-linked species, is considered to be responsible for the decrease observed in CP and CMC values of micellar solutions at all absorbed doses. There is no spectroscopic evidence of radiation damage to aromatic ring or hydrocarbon tail of surfactant. Models based on Flory-Huggins theory were employed to estimate CP from changes in mass distribution and to obtain cross-linking fractions. (Author)

  16. Polypyrrole nanoparticles fabricated via Triton X-100 micelles template approach and their acetone gas sensing property

    Energy Technology Data Exchange (ETDEWEB)

    Li, Fake; Li, Hang [Department of Clinical Laboratory Medcine, Research Institute of Surgery, Daping Hospital, Third Military Medical University, Chongqing 400042 (China); Jiang, Hongmin [26th Research Institute, Chinese Electronics Scientific and Technical Group Company, Chongqing 400060 (China); Zhang, Kejun; Chang, Kai; Jia, Shuangrong; Jiang, Wenbin; Shang, Ya; Lu, Weiping [Department of Clinical Laboratory Medcine, Research Institute of Surgery, Daping Hospital, Third Military Medical University, Chongqing 400042 (China); Deng, Shaoli, E-mail: dengsl072@yahoo.com.cn [Department of Clinical Laboratory Medcine, Research Institute of Surgery, Daping Hospital, Third Military Medical University, Chongqing 400042 (China); Chen, Ming, E-mail: chenming1971@yahoo.com [Department of Clinical Laboratory Medcine, Research Institute of Surgery, Daping Hospital, Third Military Medical University, Chongqing 400042 (China)

    2013-09-01

    Nano-scaled polypyrrole (PPy) particles have been successfully synthesized with the help of Triton X-100 micelles via soft template approach. The polypyrrole nanoparticles have been spin-coated on surface acoustic wave (SAW) transducers to demonstrate their sensing capability toward acetone gas exposure. Field Emission Scanning Electron Microscopes (FE-SEM) and Fourier transform infrared (FT-IR) spectroscopy have been utilized to characterize these PPy nanoparticles. The PPy nanoparticles have an average diameter of 95 nm. The responses of the sensors are linearly associated with the acetone concentrations in the range from 5.5 ppm to 80 ppm. In response to 5.5 ppm acetone exposure, the response and recovery time are 9 s and 8.3 s, respectively. SAW sensors coated with PPy nanoparticles were potentially useful to detect acetone.

  17. Polypyrrole nanoparticles fabricated via Triton X-100 micelles template approach and their acetone gas sensing property

    International Nuclear Information System (INIS)

    Li, Fake; Li, Hang; Jiang, Hongmin; Zhang, Kejun; Chang, Kai; Jia, Shuangrong; Jiang, Wenbin; Shang, Ya; Lu, Weiping; Deng, Shaoli; Chen, Ming

    2013-01-01

    Nano-scaled polypyrrole (PPy) particles have been successfully synthesized with the help of Triton X-100 micelles via soft template approach. The polypyrrole nanoparticles have been spin-coated on surface acoustic wave (SAW) transducers to demonstrate their sensing capability toward acetone gas exposure. Field Emission Scanning Electron Microscopes (FE-SEM) and Fourier transform infrared (FT-IR) spectroscopy have been utilized to characterize these PPy nanoparticles. The PPy nanoparticles have an average diameter of 95 nm. The responses of the sensors are linearly associated with the acetone concentrations in the range from 5.5 ppm to 80 ppm. In response to 5.5 ppm acetone exposure, the response and recovery time are 9 s and 8.3 s, respectively. SAW sensors coated with PPy nanoparticles were potentially useful to detect acetone.

  18. Pharmacological Screening ofTrachyspermum ammifor Antihyperlipidemic Activity in Triton X-100 Induced Hyperlipidemia Rat Model.

    Science.gov (United States)

    Saleem, Uzma; Riaz, Saba; Ahmad, Bashir; Saleem, Mohammad

    2017-12-01

    Mortality rate is increasing due to cardiovascular problems throughout the world. These cardiac problems are directly associated with dyslipidemia. The aim of this study was to evaluate the antihyperlipidemic effect of aqueous extract and methanol extract of Trachyspermum ammi at 1 g/kg, 3 g/kg, and 5 g/kg dose levels in rats. For this purpose, 45 male albino rats were used and randomly divided into nine equal groups ( n = 5). The lipid levels were increased after 24 h of single intraperitoneal injection of Triton X-100 (100 mg/kg) in rats. Aqueous and methanol extracts equivalent to 1 g/kg, 3 g/kg, and 5 g/kg were administered orally to the rats for 21 days. Atorvastatin (10 mg/kg) was used as standard drug. Blood samples were collected at 0, 2 nd , 9 th , 16 th , and 23 rd day by a direct cardiac puncture in Vacuette ® heparin tubes. Serum was separated and then analyzed for lipid profile, liver function test (LFT), and renal function test (RFT) using standard diagnostic kits. Results showed that extracts at 3 g/kg and 5 g/kg decreased the levels of total cholesterol, triglyceride, and low-density lipoprotein and increased high-density lipoprotein concentration in serum. T. ammi also decreased LFT and RFT parameters at the end of the study. T. ammi possessed antioxidant and antihyperlipidemic activities along with hepato- and nephro-protective effects. Aqueous and methanol extracts of T. ammi were administered orally at 1-, 3-, and 5 g/kg doses to hyperlipidemic rats (Triton X-100 induced hyperlipidemia) and atorvastatin (10 mg/kg, orally) was used as standard drug. Methanol extract at 5 g/kg showed antihyperlipidemic effect that is identical to that of standard drug. Abbreviations Used: LDL: Low-density lipoprotein; TC: Total cholesterol; VLDL: Very low-density lipoprotein; HDL: High-density lipoprotein; T. ammi : Trachyspermum ammi ; WHO: World Health Organization; CAD: Coronary artery disease; BHT: Butylated hydroxytoluene; BUN: Blood urea nitrogen; AST

  19. Pharmacological Screening of Trachyspermum ammi for Antihyperlipidemic Activity in Triton X-100 Induced Hyperlipidemia Rat Model

    Science.gov (United States)

    Saleem, Uzma; Riaz, Saba; Ahmad, Bashir; Saleem, Mohammad

    2017-01-01

    Background: Mortality rate is increasing due to cardiovascular problems throughout the world. These cardiac problems are directly associated with dyslipidemia. Aim: The aim of this study was to evaluate the antihyperlipidemic effect of aqueous extract and methanol extract of Trachyspermum ammi at 1 g/kg, 3 g/kg, and 5 g/kg dose levels in rats. Materials and Methods: For this purpose, 45 male albino rats were used and randomly divided into nine equal groups (n = 5). The lipid levels were increased after 24 h of single intraperitoneal injection of Triton X-100 (100 mg/kg) in rats. Aqueous and methanol extracts equivalent to 1 g/kg, 3 g/kg, and 5 g/kg were administered orally to the rats for 21 days. Atorvastatin (10 mg/kg) was used as standard drug. Blood samples were collected at 0, 2nd, 9th, 16th, and 23rd day by a direct cardiac puncture in Vacuette® heparin tubes. Serum was separated and then analyzed for lipid profile, liver function test (LFT), and renal function test (RFT) using standard diagnostic kits. Results: Results showed that extracts at 3 g/kg and 5 g/kg decreased the levels of total cholesterol, triglyceride, and low-density lipoprotein and increased high-density lipoprotein concentration in serum. T. ammi also decreased LFT and RFT parameters at the end of the study. Conclusion: T. ammi possessed antioxidant and antihyperlipidemic activities along with hepato- and nephro-protective effects. SUMMARY Aqueous and methanol extracts of T. ammi were administered orally at 1-, 3-, and 5 g/kg doses to hyperlipidemic rats (Triton X-100 induced hyperlipidemia) and atorvastatin (10 mg/kg, orally) was used as standard drug. Methanol extract at 5 g/kg showed antihyperlipidemic effect that is identical to that of standard drug. Abbreviations Used: LDL: Low-density lipoprotein; TC: Total cholesterol; VLDL: Very low-density lipoprotein; HDL: High-density lipoprotein; T. ammi: Trachyspermum ammi; WHO: World Health Organization; CAD: Coronary artery disease; BHT

  20. Solvent extraction of lanthanoid, yttrium and some polyvalent metal ions with phosphoric acid esters of Triton X-100

    International Nuclear Information System (INIS)

    Yoshida, Isao; Hirasawa, Jun'ichi; Tsumagari, Hiroto; Ueno, Keihei; Takagi, Makoto.

    1986-01-01

    Polyoxyethylene chain-containing nonionic surfactant, Triton X-100 (decaethyleneglycol mono(4-(1,1,3,3-tetramethylbutyl)phenyl) ether; ROH) was derived to phosphate mono-, di-, and tri-esters RH 2 PO 4 , R 2 HPO 4 and R 3 PO 4 ; abbreviated as MTP, DTP and TTP, respectively) and the metal extraction behavior of these phosphate esters was studied in 1,2-dichloroethane-water system with particular emphasis on lanthanoid(III), yttrium(III), and some other polyvalent metal ions. The extraction was carried out at pH 2 in the presence (for TTP) or in the absence (for MTP and DTP) of picric acid. The metal extraction ability of these extractants followed the order of MTP > DTP > TTP under these extraction conditions. In the extraction by MTP and DTP, the extractability of lanthanoid ions increased with the increase in their atomic number. Mean separation factor of thirteen pairs of adjacent lanthanoids was evaluated to be 1.7 for MTP and 1.4 for DTP. On the other hand, the corresponding values for TTP was almost unity. None of these compounds practically extracted other polyvalent metal ions except iron ion. Iron(III) ion was extracted with MTP and with DTP to a similar level to those of lanthanoid ions. (author)

  1. Dielectric properties of water in Triton X-100 (nonionic detergent)-water mixtures

    International Nuclear Information System (INIS)

    Asami, Koji

    2007-01-01

    Dielectric measurements were carried out for mixtures of Triton X-100 (TX, a nonionic detergent with a poly(ethylene oxide) chain) and water with or without electrolytes over a frequency range of 1 MHz to 10 GHz to study the structure and dynamics of water molecules in the mixtures. Dielectric relaxation was found above 100 MHz, being assigned to the dielectric relaxation of water. The intensity of the dielectric relaxation was proportional to the water content above 0 deg. C. Below the freezing temperature of bulk water, the relaxation intensity decreased at TX concentrations (C TX ) below 50 wt% at -10 deg. Cand below 60 wt% at -20 deg. Cbecause frozen water shifts the dielectric relaxation to a frequency region far below 1 MHz. This indicated that there is no bulk water at C TX above 50 wt% and that at least two water molecules per ethylene oxide (EO) unit are tightly associated with the ethylene oxide chain. The low-frequency conductivity of the mixtures of TX and electrolyte solutions was well represented by Bruggeman's mixture equation at C TX below 40 wt%, if two water molecules per EO unit form an insulating shell surrounding TX micelles

  2. Time-dependent association between platelet-bound fibrinogen and the Triton X-100 insoluble cytoskeleton

    International Nuclear Information System (INIS)

    Peerschke, E.I.

    1991-01-01

    Previous studies indicated a correlation between the formation of EDTA-resistant (irreversible) platelet-fibrinogen interactions and platelet cytoskeleton formation. The present study explored the direct association of membrane-bound fibrinogen with the Triton X-100 insoluble cytoskeleton of aspirin-treated, gel-filtered platelets, activated but not aggregated with 20 mumol/L adenosine diphosphate (ADP) or 150 mU/mL human thrombin (THR) when bound fibrinogen had become resistant to dissociation by EDTA. Conversion of exogenous 125I-fibrinogen to fibrin was prevented by adding Gly-Pro-Arg and neutralizing THR with hirudin before initiating binding studies. After 60 minutes at 22 degrees C, the cytoskeleton of ADP-treated platelets contained 20% +/- 12% (mean +/- SD, n = 14) of membrane-bound 125I-fibrinogen, representing 10% to 50% of EDTA-resistant fibrinogen binding. The THR-activated cytoskeleton contained 45% +/- 15% of platelet bound fibrinogen, comprising 80% to 100% of EDTA-resistant fibrinogen binding. 125I-fibrinogen was not recovered with platelet cytoskeletons if binding was inhibited by the RGDS peptide, excess unlabeled fibrinogen, or disruption of the glycoprotein (GP) IIb-IIIa complex by EDTA-treatment. Both development of EDTA-resistant fibrinogen binding and fibrinogen association with the cytoskeleton were time dependent and reached maxima 45 to 60 minutes after fibrinogen binding to stimulated platelets. Although a larger cytoskeleton formed after platelet stimulation with thrombin as compared with ADP, no change in cytoskeleton composition was noted with development of EDTA-resistant fibrinogen binding

  3. Radiolytic syntheses of hollow UO{sub 2} nanospheres in Triton X-100-based lyotropic liquid crystals

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yongming; Chen, Qingde; Shen, Xinghai [Peking Univ., Beijing (China). Fundamental Science on Radiochemistry and Radiation Chemistry Lab.

    2017-08-01

    Hollow nanospheres (φ: 60-80 nm, wall thickness: 10-20 nm), consisted of UO{sub 2} nanoparticles (φ: 3-5 nm), were successfully prepared in a Triton X-100-water (50:50, w/w) hexagonal lyotropic liquid crystal (LLC) by γ-irradiation, where water soluble ammonium uranyl tricarbonate was added as precursor. The product was stable at least up to 300 C. Furthermore, whether the nanospheres were hollow or not, and the wall thickness of the hollow nanospheres could be easily controlled via adjusting dose rate. While in the Triton X-100 based micellar systems, only solid nanospheres were obtained. At last, a possible combination mechanism containing adsorption, aggregation and fracturing processes was proposed.

  4. Multinuclear NMR characterization of CTAB-hexanol-water, sodium oleate-butanol-water and triton X-100-decanol-water microemulsions

    International Nuclear Information System (INIS)

    Nagy, J.B.; Bodart-Ravet, I.; Derouane, E.G.; Gourgue, A.; Verfaillie, J.P.

    1989-01-01

    Multinuclear NMR is a very valuable tool to characterize micellar systems or microemulsions. It allows one to determine c.m.c. values, to study the dissolution of organic molecules, the solvation of cations and anions, the structural changes occurring in a ternary diagram, the mobility of the molecules, etc. This review paper essentially deals with the characterization of cationic (CTAB-hexanol-water), anionic (sodium oleate-butanol-water) and neutral (Triton X-100-decanol-water) reversed micelles. The use of paramagnetic ions [Ni(II), CO(II), Fe(III), etc.] is particularly emphasized to characterize the site of solubilization and their interaction with surfactant and cosurfactant molecules 13 C-NMR). It is concluded, that the metallic ions are basically solvated in the inner water cores and one or more hexanol molecules are included in their first coordination shells in the CTAB-hexanol-water microemulsions. In the Triton X-100-decanol-water microemulsions, both decanol and Triton X-100 molecules enter the first coordination shell of Co(II) ions which are dissolved in both aqeous water cores and the organic medium. 19 F-NMR of a fluorinated probe molecule is particularly useful to study the size of the inner water cores. The method is based on the partition of the molecules between the interface and the organic medium. However, this method has to be applied with great care, and the computed data have to be compared to other physico-chemical results. Both 19 F- and 23 Na-NMR results show a great variation of the behaviour of the sodium oleate-butanol-water system in the so-called bicontinuous region. The Na + ions are oriented independently on a hypothetical inverse micellar droplet. (author). 43 refs.; 18 figs.; 7 tabs

  5. Colorimetric detection of melamine in milk based on Triton X-100 modified gold nanoparticles and its paper-based application

    Science.gov (United States)

    Gao, Nan; Huang, Pengcheng; Wu, Fangying

    2018-03-01

    In this study, we have developed a method for rapid, highly efficient and selective detection of melamine. The negatively charged citrate ions form an electrostatic layer on gold nanoparticles (AuNPs) and keep the NPs dispersed and stable. When citrate-capped AuNPs were further modified with Triton X-100, it stabilized the AuNPs against the conditions of high ionic strength and a broad pH range. However, the addition of melamine caused the destabilization and aggregation of NPs. This may be attributed to the interaction between melamine and the AuNPs through the ligand exchange with citrate ions on the surface of AuNPs leading Triton X-100 to be removed. As a result, the AuNPs were unstable, resulting in the aggregation. The aggregation induced a wine red-to-blue color change, and a new absorption peak around 630 nm appeared. Triton X-100-AuNPs could selectively detect melamine at the concentration as low as 5.1 nM. This probe was successfully applied to detect melamine in milk. Furthermore, paper-based quantitative detection system using this colorimetric probe was also demonstrated by integrating with a smartphone.

  6. Spectrofotometric determination of copper in sugar cane spirit using biquinoline in the presence of ethanol and Triton X-100.

    Science.gov (United States)

    do Nascimento Rocha, Sarah Adriana; Dantas, Alaílson Falcão; Jaeger, Helena Valli; Costa, Antônio Celso Spínola; Leão, Elsimar dos Santos; Gonçalves, Mara Rúbia

    2008-12-15

    The present paper proposes a method for molecular spectrophotometric determination of copper in sugar cane spirits. The copper(I) reacts with biquinoline forming a pink complex with maximum absorption at 545 nm. The reaction occurs in the presence of hydroxylamine, ethanol and Triton X-100 tensioative. Determination of copper is possible in a linear range 0.2-20.0 mgL(-1) with a detection limit 0.05 mgL(-1). The great advantages of the proposed methodology are the elimination of liquid-liquid extraction step and the use of toxic organics solvents, like dioxane, to dissolve the reagent.

  7. Application of Triton X-100 coated poly vinyl chloride as new solid ...

    African Journals Online (AJOL)

    The influences of the analytical parameters including pH, ligand amount, surfactant type and concentration, eluting condition and sample volume on metal ions recovery were investigated. The method has been ... KEY WORDS: Surfactant coated PVC, Atomic absorption spectrometry, Solid phase extraction. Bull. Chem. Soc.

  8. Cholesterol Oxidase/Triton X-100 Parked Microelectrodes for the Detection of Cholesterol in Plasma Membrane at Single Cells.

    Science.gov (United States)

    Xu, Haiyan; Zhou, Shuai; Jiang, Dechen; Chen, Hong-Yuan

    2018-01-16

    The classic electrochemical analysis of plasma membrane cholesterol at single cells utilizes a cholesterol oxidase modified microelectrode that oxidizes local cholesterol efflux from the plasma membrane to generate hydrogen peroxide for the electrochemical quantification. In this letter, a mixture of cholesterol oxidase and Triton X-100 was filled in the microcapillary that could park at the Pt layer coated tip due to slow hydrodynamic flow. During the contact of the tip with the cellular membrane, Triton X-100 at the tip permeabilized the contacted membrane to release cholesterol for the reaction with cholesterol oxidase. As compared with the linkage of cholesterol oxidase at the electrode surface, the oxidase parked in aqueous solution at the tip had a higher turnover rate resulting in larger electrochemical signal for single cell analysis. More charge collected at acyl-coA:cholesterol acyltransferase (ACAT) inhibited cells supported that this novel detection strategy could monitor the flunctation of membrane cholesterol at single cells. The successful detection of plasma membrane cholesterol at single cells using the oxidase parked microelectrode will provide a special strategy for the fabrication of biosensor that permits the integration of more molecules without functional groups at the electrode to measure active and inactive molecules in the plasma membrane. Moreover, the larger electrochemical signals collected could further increase the spatial resolution for single cell electrochemical analysis.

  9. Large transient nonproton ion movements in purple membrane suspensions are abolished by solubilization in Triton X-100.

    Science.gov (United States)

    Marinetti, T; Mauzerall, D

    1986-09-01

    Light-induced release/uptake of both protons and other ions cause transient changes in conductivity in suspensions of purple membrane (PM) fragments (Marinetti, Tim, and David Mauzerall, 1983, Proc. Natl. Acad. Sci. USA, 80:178-180). We find that the release/uptake of nonproton ions with quantum yield greater than 1 is observed at most pHs and ionic strengths. Only at both low pH and low ionic strength is the conductivity transient mostly due to protons. Our hypothesis is that during the photocycle, changes occur in the PM's dense surface charge distribution that result in changes in the number of counterions bound or condensed at the membrane surface. To test this, the PM structure was perturbed with the nonionic detergent Triton X-100. Immediately after addition, Triton does not abolish the nonproton ion movements; in fact at low detergent concentrations (0.02% vol/vol) the signal amplitudes increased considerably. However, when PM is completely solubilized into monomers in Triton, the conductivity transients are due to protons alone, though at lower quantum yield compared with native PM. These results suggest that changes in the surface charge distribution in native PM's photocycle could contribute to proton transfer between the aqueous phase and bR itself.

  10. [EFFECT OF TRITON X-100 ON LIPOSOME MEDIATED BONE MORPHOGENETIC PROTEIN 2 BY TRANSFECTION OF RAT BONE MARROW MESENCHYMAL STEM CELLS].

    Science.gov (United States)

    Xia, Delin; Huang, Mingke; Fu, Guangxing; Ma, Zheng; Wu, Shuangjiang; Zhou, Hangyu

    2015-01-01

    To study the effect of Triton X-100 promoting liposome-mediated bone morphogenetic protein 2 (BMP-2) gene transfection of rat bone marrow mesenchymal stem cells (BMSCs). BMSCs were separated and cultured from the femur and tibia of healthy Wistar rats (8-week-old, male). The 3rd passage BMSCs identified by detecting the surface antigen were used to transfect. The optimum concentration of Triton X-100 for liposome mediated gene transfection was determined with ELISA meter by the way of MTT. In optimum concentration of Triton X-100, liposome mediated BMP-2 gene was transfected to BMSCs. The experiment was divided into 3 groups according to types of trasfection agents: BMSCs were transfected with Triton X-100+liposome+BMP-2 (experimental group), with liposome+ BMP-2 (conventional transfection group), and untransfected BMSCs served as blank control group. After 48 hours of transfecting, the green fluorescent protein (GFP) in cells was detected through inverted fluorescence microscope. After 72 hours of transfection, real-time fluorescence quantitative PCR was applied to measure the mRNA expression of BMP-2. 0.01% Triton X-100 was determined to be the optimum concentration for not only making the BMSCs maintain vitality, but also achieving a certain effect on BMSCs. After trasfecting for 48 hours, GFP was observed through inverted fluorescence microscope in the experimental group and conventional transfection group, but was not observed in the blank control group. After trasfecting for 72 hours, the relative BMP-2 mRNA expression level was 5.94 ± 0.12 in the experimental group, and was 4.99 ± 0.08 in the conventional transfection group, showing significant difference (t = 360.28, P = 0.02). The transfection efficiency was increased by 19% in the experimental group. 0.010% Triton X-100 can promote the liposome mediated BMP-2 gene transfection of rat BMSUs, and can improve the transfection efficiency.

  11. Comparative proteomics of Staphylococcus aureus and the response of methicillin-resistant and methicillin-sensitive strains to Triton X-100

    DEFF Research Database (Denmark)

    Cordwell, Stuart J; Larsen, Martin Røssel; Cole, Rebecca T

    2002-01-01

    . Comparative maps were used to characterize the S. aureus response to treatment with Triton X-100 (TX-100), a detergent that has been shown to reduce methicillin resistance independently of an interaction with the mecA-encoded penicillin-binding protein 2a. In response to growth of the bacteria in the presence...

  12. Molecular basis of interactions between mitochondrial proteins and hydroxyapatite in the presence of Triton X-100, as revealed by proteomic and recombinant techniques.

    Science.gov (United States)

    Yamamoto, Takenori; Tamaki, Haruna; Katsuda, Chie; Nakatani, Kiwami; Terauchi, Satsuki; Terada, Hiroshi; Shinohara, Yasuo

    2013-08-02

    Hydroxyapatite chromatography is a very important step in the purification of voltage-dependent anion channels (VDACs) and several members of solute carrier family 25 (Slc25) from isolated mitochondria. In the presence of Triton X-100, VDACs and Slc25 members present a peculiar property, i.e., a lack of interaction with hydroxyapatite, resulting in their presence in the flow-through fraction of hydroxyapatite chromatography. This property has allowed selective isolation of VDACs and Slc25 members from a mixture of total mitochondrial proteins. However, the reason why only these few proteins are selectively obtained in the presence of Triton X-100 from the flow-though fraction of hydroxyapatite chromatography has not yet been adequately understood. In this study, when we examined the protein species in the flow-through fractions by proteomic analysis, VDAC isoforms, Slc25 members, and some other membrane proteins were identified. All the mitochondrial proteins had in common high hydrophobicity over their entire protein sequences. When the proteins were fused to soluble proteins, the fused proteins showed affinity for hydroxyapatite even in the presence of Triton X-100. Based on these results, we discussed the molecular basis of the interactions between proteins and hydroxyapatite in the presence of Triton X-100. Copyright © 2013 Elsevier B.V. All rights reserved.

  13. Streamlined Membrane Proteome Preparation for Shotgun Proteomics Analysis with Triton X-100 Cloud Point Extraction and Nanodiamond Solid Phase Extraction

    Directory of Open Access Journals (Sweden)

    Minh D. Pham

    2016-05-01

    Full Text Available While mass spectrometry (MS plays a key role in proteomics research, characterization of membrane proteins (MP by MS has been a challenging task because of the presence of a host of interfering chemicals in the hydrophobic protein extraction process, and the low protease digestion efficiency. We report a sample preparation protocol, two-phase separation with Triton X-100, induced by NaCl, with coomassie blue added for visualizing the detergent-rich phase, which streamlines MP preparation for SDS-PAGE analysis of intact MP and shot-gun proteomic analyses. MP solubilized in the detergent-rich milieu were then sequentially extracted and fractionated by surface-oxidized nanodiamond (ND at three pHs. The high MP affinity of ND enabled extensive washes for removal of salts, detergents, lipids, and other impurities to ensure uncompromised ensuing purposes, notably enhanced proteolytic digestion and down-stream mass spectrometric (MS analyses. Starting with a typical membranous cellular lysate fraction harvested with centrifugation/ultracentrifugation, MP purities of 70%, based on number (not weight of proteins identified by MS, was achieved; the weight-based purity can be expected to be much higher.

  14. UV-A photooxidation of β-carotene in Triton X-100 micelles by nitrodiphenyl ether herbicides

    International Nuclear Information System (INIS)

    Orr, G.L.; Hogan, M.E.

    1985-01-01

    Photooxidation of β-carotene in Triton X-100 micelles was stimulated by lipophilic nitrodiphenyl ether herbicides at concentrations as low as 5 μM after 15 min in UV radiation (UV-A between 315 and 400 nm). Bleaching of β-carotene by acifluorfen-methyl [methyl 5-[2-chloro-4-(trifluoromethyl)phenoxy]-2-nitrobenzoate] was proportional to UV-A intensity and independent of pH. White light (400-700 nm) alone was without effect. At pH 6.5, 100 μM acifluorfen [sodium 5-[2-chloro-4-(trifluoromethyl)phenoxy]-2-nitrobenzoate], a water-soluble nitrodiphenyl ether, stimulated photooxidation of β-carotene after 15 min in UV-A radiation. Activity of 200 μM acifluorfen was enhanced at pHs between 3.5 and 6.5. The chlorodiphenyl ether analogue of acifluorfen-methyl, methyl 5-[2-chloro-4-(trifluoromethyl)phenoxy]-2-chlorobenzoate, exhibited little activity at 200 μM and 200 μM phenyl ether was without effect. Activation energy for acifluorfen-methyl stimulated β-carotene photooxidation near 20 and 30 0 C was 40.3 and 5.6 kJ mol -1 , respectively. Subsequent to UV-A exposure and placement into darkness no further bleaching of β-carotene was detected, indicating that reactive species were generated only in light and consumed quickly in darkness

  15. High transmittance cadmium oxysulfide Cd(S,O) buffer layer grown by triton X-100 mediated chemical bath deposition for thin-film heterojunction solar cells

    Science.gov (United States)

    Ballipinar, Faruk; Rastogi, A. C.

    2017-01-01

    Polycrystalline 100-190 nm Cd(S,O) n-type semiconductor thin films of high transparency in the visible range are deposited by a surfactant Triton X-100 mediated chemical bath deposition process. The crystalline structure of the films revealed by X-ray diffraction data shows a cubic-CdO phase signified by (111) and (200) planes alongside the (002), (220), and (110) planes from hexagonal-CdS. The invariance of the 2θ position of the (002) CdS diffraction is interpreted in terms of the growth of the composite film essentially by the formation of a dilute interstitial alloy of CdO and CdS. This is confirmed by Raman spectra which, besides the CdS 1LO and 2LO modes at 300 and 600 cm-1, also show Raman lines from CdO at 1098 cm-1 and 952 cm-1 assigned as overtone of 2LO phonon modes and 556 cm-1 due to band crossing between LO and TO modes of CdO. Optical spectra of Cd(S,O) films show a median transmittance of >85% compared to ˜70% for CdS films in the 550-1000 nm wavelength range. The Cd(S,O) films show optical bandgap varying from 2.34 to 2.26 eV with increasing CdO fraction but retain high sub-bandgap transmission and sharp band edge threshold. The Cd(S,O) films thus offer an alternative to the CdS buffer layer in the heterojunction solar cells, which has major shortcoming of poor stability and high sub-bandgap absorption. The photoluminescence spectra of Cd(S,O) films show three green bands, of which one is the near band edge transition at 511.5 nm, the same as in CdS, the second band at 526.0 nm that red shifted from the CdS position is due to shallow donor-acceptor defects arising from structural change due to CdO, and the third band at 543.6 nm (2.28 eV) originates from direct band transition in CdO. The growth mechanism of Cd(S,O) films is described, which invokes that the Triton X-100 molecule modifies the microenvironment around adsorbed [Cd(NH3)4]2+ species, thereby inducing two concurrent reactions, one with SH- species that cause CdS formation and the

  16. Extraction and separation of tungsten (VI) from aqueous media with Triton X-100-ammonium sulfate-water aqueous two-phase system without any extractant.

    Science.gov (United States)

    Yongqiang Zhang; Tichang Sun; Tieqiang Lu; Chunhuan Yan

    2016-11-25

    An aqueous two-phase system composed of Triton X-100-(NH 4 ) 2 SO 4 -H 2 O was proposed for extraction and separation of tungsten(VI) from aqueous solution without using any extractant. The effects of aqueous pH, concentration of ammonium sulfate, Triton X-100 and tungsten, extracting temperature on the extraction of tungsten were investigated. The extraction of tungsten has remarkable relationship with aqueous pH and are to above 90% at pH=1.0-3.0 under studied pH range (pH=1.0-7.0) and increases gradually with increasing Triton X-100 concentration, but decreases slightly with increasing ammonium sulfate concentration. The extraction percentage of tungsten is hardly relevant to temperature but its distribution coefficient linearly increases with increasing temperature within 303.15-343.15K. The distribution coefficient of tungsten increases with the increase of initial tungsten concentration (0.1-3%) and temperature (303.15 K-333.15K). The solubilization capacity of tungsten in Triton X-100 micellar phase is independent of temperature. FT-IR analysis reveals that there is no evident interaction between polytungstate anion and ether oxygen unit in Triton X-100, and DLS analysis indicates that zeta potential of Triton X-100 micellar phase have a little change from positive to negative after extracting tungsten. Based on the above-mentioned results, it can be deduced that polytungstate anions are solubilized in hydrophilic outer shell of Triton X-100 micelles by electrostatic attraction depending on its relatively high hydrophobic nature. The stripping of tungsten is mainly influenced by temperature and can be easily achieved to 95% in single stage stripping. The tungsten (VI) is separated out from solution containing Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Al(III), Cr(III) and Mn(II) under the suitable conditions. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Chemical synthesis of flower-like hybrid Cu(OH)2/CuO electrode: Application of polyvinyl alcohol and triton X-100 to enhance supercapacitor performance.

    Science.gov (United States)

    Shinde, S K; Fulari, V J; Kim, D-Y; Maile, N C; Koli, R R; Dhaygude, H D; Ghodake, G S

    2017-08-01

    In this research article, we report hybrid nanomaterials of copper hydroxide/copper oxide (Cu(OH) 2 /CuO). A thin films were prepared by using a facile and cost-effective successive ionic layer adsorption and reaction (SILAR) method. As-synthesized and hybrid Cu(OH) 2 /CuO with two different surfactants polyvinyl alcohol (PVA) and triton-X 100 (TRX-100) was prepared having distinct morphological, structural, and supercapacitor properties. The surface of the thin film samples were examined by scanning electron microscopy (SEM). A nanoflower-like morphology of the Cu(OH) 2 /CuO nanostructures arranged vertically was evidenced on the stainless steel substrate. The surface was well covered by nanoflake-like morphology and formed a uniform Cu(OH) 2 /CuO nanostructures after treating with surfactants. X-ray diffraction patterns were used to confirm the hybrid phase of Cu(OH) 2 /CuO materials. The electrochemical properties of the pristine Cu(OH) 2 /CuO, PVA:Cu(OH) 2 /CuO, TRX-100:Cu(OH) 2 /CuO films were observed by cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy technique. The electrochemical examination reveals that the Cu(OH) 2 /CuO electrode has excellent specific capacitance, 292, 533, and 443Fg -1 with pristine, PVA, and TRX-100, respectively in 1M Na 2 SO 4 electrolyte solution. The cyclic voltammograms (CV) of Cu(OH) 2 /CuO electrode shows positive role of the PVA and TRX-100 to enhance supercapacitor performance. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Determination of trace amounts of nickel(II) with α-(2-Benzimidazolyl)-α',α''-(N-5-nitro-2-pyridyl hydrazone) toluene in the presence of triton X-100 by fluorescence method

    International Nuclear Information System (INIS)

    Park, Chan Il; Kim, Hyun Soo; Cha, Ki Won

    2000-01-01

    A method is described for the fluorimetric determination of nicke, based on the formation of Ni(II)-α-(2-Benzimidazolyl)-α',α''-(N-5-nitro-2-pyridyl hydrazone)-toluene complex in the presence of a non-ionic surfactant. The complex has practically no fluorescence in the absence of surfactant, but the addition of Triton X-100 makes possible the fluorimetric determination of low concentrations of Ni(II) as it enhances the fluorescence intensity of the complex by up to about 5-fold. This method is very sensitive and selective for the direct determination of nickel ion. The optimum conditions are a Triton X-100 concentration of 2.0 mL (5.0%, v/v) and pH 9.0 ± 0.2 (ammonium chloride-ammonia buffer). The fluorescence is measured at 337 nm of emission wavelength under 300 nm of excitation wavelength. The fluorescence intensity is a linear function of the concentration of Ni(II) in the range 5-70 ng/mL, and the detection limit is 2.0 ng/mL. The proposed method has been successfully applied to the determination of trace amounts of Ni(II) in food and human hair samples

  19. Zirconium-titanium-phosphate nanoparticles. Triton X-100 based size modification, characterization and application in radiochemical separation

    Energy Technology Data Exchange (ETDEWEB)

    Chakraborty, R.; Sen, B.; Chattopadhyay, P. [Burdwan Univ. (India). Dept. of Chemistry

    2014-07-01

    Zirconium-titanium-phosphate nanoparticles (ZTP) of different sizes were synthesized using tritron X-100 (polyethylene glycol-p-isooctylphenyl ether) surfactant. The materials were characterized by FTIR and powdered X-ray diffraction (XRD). The structural and morphological details of the material were obtained by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The SEM study was followed by energy dispersive spectroscopic analysis (EDS) for elemental analysis of the sample. The important peaks of the XRD spectra were analyzed to determine the probable composition of the material. The particle sizes were determined by dynamic light scattering (DLS) method. Ion exchange capacity was measured for different metal ions with sizes of the ZTP nanoparticles and size-dependent ion exchange property of the material was investigated thoroughly. The nanomaterial of the smallest size of around 5 nm was employed to separate carrier-free {sup 137m}Ba from {sup 137}Cs in column chromatographic technique using 1.0 M HNO{sub 3} as eluting agent at pH = 5. (orig.)

  20. Toltrazuril mixed nanomicelle delivery system based on sodium deoxycholate-Brij C20 polyethylene ether-triton x100: Characterization, solubility, and bioavailability study.

    Science.gov (United States)

    Zhang, Li; Ren, Dandan; Zhou, Jianyu; Peng, Guangneng; Shu, Gang; Yuan, Zhixiang; Shi, Fei; Zhao, Ling; Yin, Lizi; Fan, Guoqing; Liu, Chang; Fu, Hualin

    2018-03-01

    Toltrazuril (Tol) is a broad-spectrum anticoccidiosis drug that is widely used in the prevention and treatment of coccidiosis infection in poultry and mammals. However, the drug has poor aqueous solubility (25 °C, 0.41 μg/mL), and its dose escalation for systemic administration remains challenging. We engineered a Tol mixed nanomicelle (TMNM) delivery system based on sodium deoxycholate-Brij C20 polyethylene ether-triton x100 (NaDC-Brij58-Tx100) as surfactants by film hydration method. The physical properties of TMNM were characterized, and the pharmacokinetic parameters of Tol and TMNM were compared. The average particle size, drug loading, saturated solubility, and critical micelle concentration (CMC) of the TMNM system were 12.28 ± 0.48 nm, 3.38 ± 0.12%, 3921.70 ± 0.01 μg/mL (8170-fold compared with Tol), and 0.0172 mg/mL, respectively. Transmission electron microscopy (TEM), scanning electron microscopy (SEM) micrographs, differential scanning calorimetry (DSC) and X-ray diffraction (XRD) were performed, and the results showed TMNM formation. Furthermore, the TMNM had greater bioavailability (215%) than the Tol solution. The significant increase in the drug solubility and bioavailability of TMNM suggested the TMNM is a potential oral and parenteral delivery system for Tol and has wide application prospects in the clinical context. Copyright © 2017 Elsevier B.V. All rights reserved.

  1. High-Yield and Sustainable Production of Phosphatidylserine in Purely Aqueous Solutions via Adsorption of Phosphatidylcholine on Triton-X-100-Modified Silica.

    Science.gov (United States)

    Zhang, Xiaoli; Li, Binglin; Wang, Jiao; Li, Huanyu; Zhao, Binxia

    2017-12-13

    Triton X-100 was covalently bound to a surface of silica and acted as an anchor molecule to facilitate the adsorption of phosphatidylcholine (PC) in a purely aqueous solution. The silica-adsorbed PC obtained was successfully used for phospholipase D (PLD)-mediated transphosphatidylation in the production of phosphatidylserine (PS). Organic solvents were completely avoided in the whole production process. The PC loading and PS yield reached 98.9 and 99.0%, respectively. Two adsorption models were studied, and the relevant parameters were calculated to help us understand the adsorption and reaction processes deeply. In addition, the silica-adsorbed PC provides a promising way to continuously biosynthesize PS. A packed-bed reactor was employed to demonstrate the process flow of the continuous production of PS. The recyclability and stability of the Triton-X-100-modified silica were excellent, as demonstrated by its use 30 times during continuous operation without any loss of the productivity.

  2. Rho-kinase inhibition attenuates calcium-induced contraction in β-escin but not Triton X-100 permeabilized rabbit femoral artery.

    Science.gov (United States)

    Clelland, Lyndsay J; Browne, Brendan M; Alvarez, Silvina M; Miner, Amy S; Ratz, Paul H

    2011-09-01

    K+-depolarization (KCl) of smooth muscle has long been known to cause Ca2+-dependent contraction, but only recently has this G protein-coupled receptor (GPCR)-independent stimulus been associated with rhoA kinase (ROCK)-dependent myosin light chain (MLC) phosphatase inhibition and Ca2+ sensitization. This study examined effects of ROCK inhibition on the concentration-response curves (CRCs) generated in femoral artery by incrementally adding increasing concentrations of KCl to intact tissues, and Ca2+ to tissues permeabilized with Triton X-100, β-escin and α-toxin. For a comparison, tissue responses were assessed also in the presence of protein kinase C (PKC) and MLC kinase inhibition. The ROCK inhibitor H-1152 induced a strong concentration-dependent inhibition of a KCl CRC. A relatively low GF-109203X concentration (1 μM) sufficient to inhibit conventional PKC isotypes also inhibited the KCl CRC but did not affect the maximum tension. ROCK inhibitors had no effect on the Ca2+ CRC induced in Triton X-100 or α-toxin permeabilized tissues, but depressed the maximum contraction induced in β-escin permeabilized tissue. GF-109203X at 1 μM depressed the maximum Ca2+-dependent contraction induced in α-toxin permeabilized tissue and had no effect on the Ca2+ CRC induced in Triton X-100 permeabilized tissue. The MLC kinase inhibitor wortmannin (1 μM) strongly depression the Ca2+ CRCs in tissues permeabilized with Triton X-100, α-toxin and β-escin. H-1152 inhibited contractions induced by a single exposure to a submaximum [Ca2+] (pCa 6) in both rabbit and mouse femoral arteries. These data indicate that β-escin permeabilized muscle preserves GPCR-independent, Ca2+- and ROCK-dependent, Ca2+ sensitization.

  3. ATP-induced reactivation of ram testicular, cauda epididymal, and ejaculated spermatozoa extracted with Triton X-100.

    Science.gov (United States)

    White, I G; Voglmayr, J K

    1986-02-01

    It was possible to demembrante and reactivate not only freshly collected testicular, cauda epididymal, and ejaculated ram sperm but also sperm that had been stored for several days at 0 degrees C and for several months at -196 degrees C in rete testis fluid or egg yolk citrate media. Sperm were usually washed free of seminal plasma before demembranation, but this was not essential for reactivation. Bovine serum albumin (1.0%) in the wash medium increased the survival of sperm, but more than 0.25% in the extraction medium decreased reactivation. A macro-molecular component of cauda epididymal fluid also inhibited the reactivation of testicular sperm. Triton X-100 concentrations between 0.01% and 1.00% in the extraction medium were satisfactory for demembranating the sperm. Rapid cooling (i.e., cold shock) mimicked the effect of detergent in making the sperm responsive to added ATP and demonstrated that damage to ram sperm in cold shock does not involve the axoneme. Ejaculated and cauda sperm were reactivated immediately on addition of ATP and activity persisted for up to 10 min. Testicular sperm, on the other hand, required about 4 min to become fully reactivated. The optimal ATP concentration for activation of sperm was 0.1-1.0 mM. Magnesium ions (0.1-1.0 mM) were important for reactivation, and testicular sperm required a higher magnesium concentration than did cauda or ejaculated sperm. Manganese ions were almost as effective as magnesium for reactivating cauda epididymal and ejaculated sperm. Cobalt and cadmium ions were much less active for cauda and ejaculated sperm and none of these ions were effective for testicular sperm. Fluoride (25-50 mM) inhibited reactivation. The presence of 50 microM cAMP in the extraction medium or preincubation of testicular sperm with theophylline or caffeine increased low levels of activation, but this was not evident with ejaculated or cauda sperm. We conclude that the motor apparatus is already functionally assembled in

  4. Phase behaviour and microstructure of the micro-emulsions composed of cholinium-based ionic liquid, Triton X-100 and water

    International Nuclear Information System (INIS)

    Pei, Yuanchao; Huang, Yanjie; Li, Lin; Wang, Jianji

    2014-01-01

    Highlights: • The microemulsions composed of cholinium-based ionic liquid, Triton X-100 and water have been prepared and characterised. • Ternary phase diagrams of the microemulsions have been established at T = 298.15 K. • The microemulsions exhibit IL-in-water, bicontinuous and water-in-IL microstructures. • Droplets with the size smaller than 20 nm are formed in these IL-based microemulsions. - Abstract: In this paper, micro-emulsions composed of cholinium-based ionic liquids (ILs), octylphenol ethoxylate (Triton X-100) and water were prepared. These ternary systems were found to be stable over 12 months at room temperature. Their phase behaviour was investigated by using cloud titrations, and their microstructures were characterised by means of cyclic voltammetry and electrical conductance measurements at T = 298.15 K. It was shown that the micro-emulsions exhibited IL-in-water, bi-continuous and water-in-IL microstructures. Dynamic light scattering data suggest that Triton X-100 forms micelles in water, which were swelled by the ILs added. Droplets with the size about 20 nm were formed in these IL-based micro-emulsions, and the droplet size increased with the increase of the IL concentrations. These IL-based micro-emulsions may have potential in drug delivery, chemical reactions and nanomaterial preparation as a new type of nanoreactors

  5. Inhibitory effect of non-ionic surfactants of the TRITON-X series on the corrosion of carbon steel in sulphuric acid

    International Nuclear Information System (INIS)

    Fuchs-Godec, R.

    2007-01-01

    The corrosion inhibition characteristics of non-ionic surfactants of the TRITON-X series, known as TRITON-X-100 and TRITON-X-405, on stainless steel (SS) type X4Cr13 in sulphuric acid were investigated by potentiodynamic polarisation measurements. It was found that these surfactants act as good inhibitors of the corrosion of stainless steel in 2 mol L -1 H 2 SO 4 solution, but the inhibition efficiency strongly depends on the electrode potential. The polarisation data showed that the non-ionic surfactants used in this study acted as mixed-type inhibitors and adsorb on the stainless steel surface, in agreement with the Flory-Huggins adsorption isotherm. Calculated ΔG ads values are -57.79 kJ mol -1 for TRITON-X-100, and -87.5 kJ mol -1 for TRITON-X-405. From the molecular structure it can be supposed that these surfactants adsorb on the metal surface through two lone pairs of electrons on the oxygen atoms of the hydrophilic head group, suggesting a chemisorption mechanism

  6. Application of Triton X-100 coated poly vinyl chloride as new solid phase for preconcentration of Fe3+, Cu2+ and Zn2+ ions and their flame atomic absorption spectrometric determinations

    Directory of Open Access Journals (Sweden)

    Mehrorang Ghaedi

    2010-04-01

    Full Text Available A selective, sensitive and efficient method for preconcentration of trace amounts of Cu(II, Fe(II and Zn(II ions based on the uptake of their complexes with 3-((indolin-3-yl(phenylmethylindoline (IYPMI loaded on Triton X-100 coated poly vinyl chloride has been reported. The influences of the analytical parameters including pH, ligand amount, surfactant type and concentration, eluting condition and sample volume on metal ions recovery were investigated. The method has been successfully applied for the extraction of these ions content in some real samples of soil and plants. The extraction efficiency was > 97% with low relative standard deviation (RSD < 2.4% and the preconcentration factor of 90 (5 mL elution volume for a 450 mL of sample volume.

  7. Intermolecular electron transfer between coumarin dyes and aromatic amines in Triton-X-100 micellar solutions: Evidence for Marcus inverted region

    International Nuclear Information System (INIS)

    Kumbhakar, Manoj; Nath, Sukhendu; Mukherjee, Tulsi; Pal, Haridas

    2004-01-01

    Photoinduced electron transfer (ET) between coumarin dyes and aromatic amines has been investigated in Triton-X-100 micellar solutions and the results have been compared with those observed earlier in homogeneous medium. Significant static quenching of the coumarin fluorescence due to the presence of high concentration of amines around the coumarin fluorophore in the micelles has been observed in steady-state fluorescence studies. Time-resolved studies with nanosecond resolutions mostly show the dynamic part of the quenching for the excited coumarin dyes by the amine quenchers. A correlation of the quenching rate constants, estimated from the time-resolved measurements, with the free energy changes (ΔG 0 ) of the ET reactions shows the typical bell shaped curve as predicted by Marcus outer-sphere ET theory. The inversion in the ET rates for the present systems occurs at an exergonicity (-ΔG 0 ) of ∼0.7-0.8 eV, which is unusually low considering the polarity of the Palisade layer of the micelles where the reactants reside. Present results have been rationalized on the basis of the two dimensional ET model assuming that the solvent relaxation in micellar media is much slower than the rate of the ET process. Detailed analysis of the experimental data shows that the diffusional model of the bimolecular quenching kinetics is not applicable for the ET reactions in the micellar solutions. In the present systems, the reactions can be better visualized as equivalent to intramolecular electron transfer processes, with statistical distribution of the donors and acceptors in the micelles. A low electron coupling (V el ) parameter is estimated from the correlation of the experimentally observed and the theoretically calculated ET rates, which indicates that the average donor-acceptor separation in the micellar ET reactions is substantially larger than for the donor-acceptor contact distance. Comparison of the V el values in the micellar solution and in the donor

  8. Intermolecular electron transfer between coumarin dyes and aromatic amines in Triton-X-100 micellar solutions: Evidence for Marcus inverted region

    Science.gov (United States)

    Kumbhakar, Manoj; Nath, Sukhendu; Mukherjee, Tulsi; Pal, Haridas

    2004-02-01

    Photoinduced electron transfer (ET) between coumarin dyes and aromatic amines has been investigated in Triton-X-100 micellar solutions and the results have been compared with those observed earlier in homogeneous medium. Significant static quenching of the coumarin fluorescence due to the presence of high concentration of amines around the coumarin fluorophore in the micelles has been observed in steady-state fluorescence studies. Time-resolved studies with nanosecond resolutions mostly show the dynamic part of the quenching for the excited coumarin dyes by the amine quenchers. A correlation of the quenching rate constants, estimated from the time-resolved measurements, with the free energy changes (ΔG0) of the ET reactions shows the typical bell shaped curve as predicted by Marcus outer-sphere ET theory. The inversion in the ET rates for the present systems occurs at an exergonicity (-ΔG0) of ~0.7-0.8 eV, which is unusually low considering the polarity of the Palisade layer of the micelles where the reactants reside. Present results have been rationalized on the basis of the two dimensional ET model assuming that the solvent relaxation in micellar media is much slower than the rate of the ET process. Detailed analysis of the experimental data shows that the diffusional model of the bimolecular quenching kinetics is not applicable for the ET reactions in the micellar solutions. In the present systems, the reactions can be better visualized as equivalent to intramolecular electron transfer processes, with statistical distribution of the donors and acceptors in the micelles. A low electron coupling (Vel) parameter is estimated from the correlation of the experimentally observed and the theoretically calculated ET rates, which indicates that the average donor-acceptor separation in the micellar ET reactions is substantially larger than for the donor-acceptor contact distance. Comparison of the Vel values in the micellar solution and in the donor-acceptor close

  9. Comparative proteomics of Staphylococcus aureus and the response of methicillin-resistant and methicillin-sensitive strains to Triton X-100

    DEFF Research Database (Denmark)

    Cordwell, Stuart J; Larsen, Martin Røssel; Cole, Rebecca T

    2002-01-01

    profiles of S. aureus strains COL (methicillin-resistant) and 8325 (methicillin-sensitive). Reference mapping via this approach identified 377 proteins that corresponded to 266 distinct ORFs. Amongst these identified proteins were 14 potential virulence factors. The production of 41 'hypothetical' proteins....... Comparative maps were used to characterize the S. aureus response to treatment with Triton X-100 (TX-100), a detergent that has been shown to reduce methicillin resistance independently of an interaction with the mecA-encoded penicillin-binding protein 2a. In response to growth of the bacteria in the presence...

  10. Simultaneous Spectrophotometric Determination of Copper, Nickel, and Zinc Using 1-(2-Thiazolylazo)-2-Naphthol in the Presence of Triton X-100 Using Chemometric Methods

    International Nuclear Information System (INIS)

    Low, Kah Hin; Zain, Sharifuddin Md; Abas, Mhd. Radzi; Misran, Misni; Mohd, Mustafa Ali

    2009-01-01

    Multivariate models were developed for the simultaneous spectrophotometric determination of copper (II), nickel (II) and zinc (II) in water with 1-(2-thiazolylazo)-2-naphthol as chromogenic reagent in the presence of Triton X-100. To overcome the drawback of spectral interferences, principal component regression (PCR) and partial least square (PLS) multivariate calibration approaches were applied. Performances were validated with several test sets, and their results were then compared. In general, no significant difference in analytical performance between PLS and PCR models. The root mean square error of prediction (RMSEP) using three components for Cu 2+ , Ni 2+ and Zn 2+ were 0.018, 0.010, 0.011 ppm, respectively. Figures of merit such as sensitivity, analytical sensitivity, limit of detection (LOD) were also estimated. High reliability was achieved when the proposed procedure was applied to simultaneous determination of Cu 2+ , Ni 2+ and Zn 2+ in synthetic mixture and tap water

  11. Cloud point extraction and speciation of iron(3) of 10-7-10-6 M level using 8-quinolinol derivatives and triton X-100

    International Nuclear Information System (INIS)

    Ohashi, K.; Ougiyanagi, J.; Choi, S.Y.; Ito, H.; Imura, H.

    2001-01-01

    The cloud point extraction behaviour, specification, and determination of traces of iron(III) with 8-quinolinol derivatives (HA), such as 8-quinolinol (HQ), 2-methyl-8-quinolinol (HMQ), and 2-methyl-5-octyl-oxy-methyl-8-quinolinol (HMO 8 Q) were investigated. Above pH 4.0, more than 95% of iron(III) was extracted with 5.00 x 10 -2 M HQ, HMQ, and HMO 8 Q in 4 (v/v)% Triton X-100. The proposed method was applied to the determination of iron(III) in the Riverine Water Reference (JAC 0031 and JAC 0032) by graphite furnace atomic absorption spectrometry. The results agreed well with the certified values within 2% of the RSD. (authors)

  12. Separation of Cr(III) from Cr(VI) by Triton X-100 Cerium (Iv) Phosphate as a Surface Active Ion Exchanger

    International Nuclear Information System (INIS)

    El-Azony, K.M.; Ismail Aydia, M.; El-Mohty, A.A.

    2010-01-01

    A new and simple high-performance liquid chromatography (HPLC) method with ultraviolet (UV) detection has been developed for the determination of both Cr (III) and Cr (VI) ions. Chromium species were determined by HPLC using a stationary phase consisting of a reversed phase column (Nucleosil phenyl column; 250 mm x 4.6 mm,5 μm), and a mobile phase consisting of a mixture of methanol: water(70 : 30 v/v), in which the complexing agent di-(2-ethylhexyl) phosphoric acid (DEHPA) was dissolved. The UV detection was carried out at wavelength 650 nm. Separation of Cr (III) from Cr (VI) on Triton X-100 cerium(IV) phosphate(TX-100 CeP) as a surface active ion exchanger was investigated. TX-100 CeP has been synthesized, characterized using IR, X-Ray, TGA/DTA and elemental analysis. The ion exchange capacity and chemical stability in different HCl concentration have been studied

  13. Obtaining Soluble Folded Proteins from Inclusion Bodies Using Sarkosyl, Triton X-100, and CHAPS: Application to LB and M9 Minimal Media.

    Science.gov (United States)

    Massiah, Michael A; Wright, Katharine M; Du, Haijuan

    2016-04-01

    This unit describes a straightforward and efficient method of using sarkosyl to solubilize and recover difficult recombinant proteins, such as GST- and His6 -tagged fusion proteins, that are overexpressed in E. coli. This protocol is especially useful for rescuing recombinant proteins overexpressed in M9 minimal medium. Sarkosyl added to lysis buffers helps with both protein solubility and cell lysis. Higher percentage sarkosyl (up to 10%) can extract >95% of soluble protein from inclusion bodies. In the case of sarkosyl-solubilized GST-fusion proteins, batch-mode affinity purification requires addition of a specific ratio of Triton X-100 and CHAPS, while sarkosyl-solubilized His6 -tagged fusion proteins can be directly purified on Ni(2+) resin columns. Proteins purified by this method could be widely used in biological assays, structure analysis and mass spectrum assay. Copyright © 2016 John Wiley & Sons, Inc.

  14. The role of Triton surfactant in anisotropic etching of {1 1 0} reflective planes on (1 0 0) silicon

    Science.gov (United States)

    Resnik, Drago; Vrtacnik, Danilo; Aljancic, Uros; Mozek, Matej; Amon, Slavko

    2005-06-01

    Etching characteristics and properties of {1 1 0} silicon crystal planes used as 45° optical mirrors for deflecting optical beams from/to optical fibers were investigated. Fiber aligning grooves and passive mirror-like planes were realized by wet micromachining of (1 0 0) silicon in KOH IPA and TMAH IPA systems. Implementation of Triton-x-100 surfactant as an additive to 25% TMAH in anisotropic etching of {1 1 0} silicon passive mirror planes is reported and discussed. It was found that Triton-x-100 contents in the range of 10 200 ppm to the 25% TMAH water etchant significantly increase the anisotropy mostly by decreasing the {1 1 0} etch rate and retaining the {1 0 0} etch rate. It is also shown that {1 1 0} surface roughness is substantially improved compared to two other etching systems. Furthermore, efficient convex corner underetching reduction is demonstrated. The results of optical characterization of passive mirrors with 632 nm incident light show reduced scattering of reflected optical beam due to improved microroughness for mirrors made by TMAH Triton. For the reflection of the optical beam with 1.33 µm and 1.54 µm wavelengths, sputtered layer of gold is used as reflective coating on silicon mirrors thus increasing the reflected optical beam intensity by an additional 8%.

  15. Two-step preparation of nano-scaled magnetic chitosan particles using Triton X-100 reversed-phase water-in-oil microemulsion system

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Zhengkun; Jiang, Feihong [College of Food Science and Engineering, Northwest A and F University, Yangling, Shaanxi 712100 (China); Lee, Tung-Ching, E-mail: lee@aesop.rutgers.edu [Department of Food Science, Rutgers, the State University of New Jersey, 65 Dudley Road, New Brunswick, NJ 08901 (United States); Yue, Tianli, E-mail: yuetl305@nwsuaf.edu.cn [College of Food Science and Engineering, Northwest A and F University, Yangling, Shaanxi 712100 (China)

    2013-12-25

    Highlights: •A new two-step route for nano-scaled magnetic chitosan particles preparation. •Triton X-100 reversed-phase microemulsion system was used for chitosan coating. •Narrow size distribution of magnetic chitosan nanoparticles was achieved. •Quantitative evaluation of recoverability for the magnetic chitosan nanoparticles. -- Abstract: A new two-step route for the preparation of nano-scaled magnetic chitosan particles has been developed, different from reported one-step in situ preparation and two-step preparation method of reversed-phase suspension, Triton X-100 reversed-phase water-in-oil microemulsion encapsulation method was employed in coating the pre-prepared Fe{sub 3}O{sub 4} nanoparticles with chitosan. The resultant magnetic chitosan particles owned a narrow size distribution ranging from 50 to 92 nm. X-ray diffraction patterns (XRD) indicated that the chitosan coating procedure did not change the spinal structure of Fe{sub 3}O{sub 4} magnetic nanoparticles. The results of Fourier transform infrared (FTIR) analysis and thermogravimetric analysis (TGA) demonstrated that the chitosan was coated on Fe{sub 3}O{sub 4} nanoparticles and its average mass content was ∼50%. The saturated magnetization of the magnetic Fe{sub 3}O{sub 4}/chitosan nanoparticles reached 18.62 emu/g, meanwhile, the nanoparticles showed the characteristics of superparamagnetism. The magnetic chitosan nanoparticles showed a high recoverability of 99.99% in 10 min when pH exceeded 4. The results suggested that the as-prepared magnetic chitosan particles were nano-scaled with a narrow size distribution and a high recoverability.

  16. Two-step preparation of nano-scaled magnetic chitosan particles using Triton X-100 reversed-phase water-in-oil microemulsion system

    International Nuclear Information System (INIS)

    Zhou, Zhengkun; Jiang, Feihong; Lee, Tung-Ching; Yue, Tianli

    2013-01-01

    Highlights: •A new two-step route for nano-scaled magnetic chitosan particles preparation. •Triton X-100 reversed-phase microemulsion system was used for chitosan coating. •Narrow size distribution of magnetic chitosan nanoparticles was achieved. •Quantitative evaluation of recoverability for the magnetic chitosan nanoparticles. -- Abstract: A new two-step route for the preparation of nano-scaled magnetic chitosan particles has been developed, different from reported one-step in situ preparation and two-step preparation method of reversed-phase suspension, Triton X-100 reversed-phase water-in-oil microemulsion encapsulation method was employed in coating the pre-prepared Fe 3 O 4 nanoparticles with chitosan. The resultant magnetic chitosan particles owned a narrow size distribution ranging from 50 to 92 nm. X-ray diffraction patterns (XRD) indicated that the chitosan coating procedure did not change the spinal structure of Fe 3 O 4 magnetic nanoparticles. The results of Fourier transform infrared (FTIR) analysis and thermogravimetric analysis (TGA) demonstrated that the chitosan was coated on Fe 3 O 4 nanoparticles and its average mass content was ∼50%. The saturated magnetization of the magnetic Fe 3 O 4 /chitosan nanoparticles reached 18.62 emu/g, meanwhile, the nanoparticles showed the characteristics of superparamagnetism. The magnetic chitosan nanoparticles showed a high recoverability of 99.99% in 10 min when pH exceeded 4. The results suggested that the as-prepared magnetic chitosan particles were nano-scaled with a narrow size distribution and a high recoverability

  17. Estabilización y desestabilización por adsorción sobre coloides modelo de Triton X-100

    Directory of Open Access Journals (Sweden)

    Romero-Cano, M. S.

    2000-08-01

    Full Text Available The colloidal stability of polystyrene particles with different surface functional groups (sulfate and carboxyl has been studied after adsorption of Triton X-100. The coverage degree and the medium pH were the main factors in this study. Three different types of colloidal stabilization were found, which can be clasified as a function of the relationship between the atractive interaction energy (VA, Van der Waals type and the steric interaction energy (VS, repulsive type: electrostatic (VS = 0, electrosteric (VS < ⎥VA⎥, and steric (VS > ⎥VA⎥. The main difference between these stabilization types is the response against the electrolyte concentration: the first and second cases are affected by electrolyte addition, while the third one does not.

    Se ha estudiado la estabilidad coloidal de partículas de poliestireno con diferente funcionalidad superficial (sulfato y carboxilo después de la adsorción de Triton X-100. El grado de recubrimiento y el pH del medio fueron variables fundamentales en el estudio. Se han encontrado tres tipos diferentes de estabilización coloidal que pueden clasificarse en función de la relación entre la energía de interacción atractiva de van der Waals (VA y la energía de interacción repulsiva de origen estérico (VS: electrostático (VS = 0, electroestérico (VS < ⎥VA⎥ y estérico (VS >⎥VA⎥. La diferencia fundamental entre estos tres tipos de estabilización es la respuesta frente a la concentración de electrolito: los dos primeros son sensibles a la adición del mismo mientras que el último no lo es. Adicionalmente se han encontrado fenómenos de desestabilización, no predichos por la teoría DLVO extendida, los cuales dependen de la funcionalidad superficial, del grado de recubrimiento y del pH del medio de dispersión.

  18. Separation of Cr(III) from Cr(VI) by Triton X-100 cerium(IV) phosphate as a surface active ion exchanger

    International Nuclear Information System (INIS)

    El-Azony, K.M.; Ismail Aydia, M.; El-Mohty, A.A.

    2011-01-01

    Triton X-100 cerium(IV) phosphate (TX-100CeP) was synthesized and characterized by using IR, X-ray, TGA/DT and the elemental analysis. The chemical stability of TX-100CeP versus the different concentrations of HCl acid was studied before and after its exposure to the radiation dose (30 K Gray). The effect of HCl concentration on separation of Cr(III) from Cr(VI) by using TX-100CeP as surface active ion exchanger was also studied. A novel method was achieved for the quantifying of Cr(III) and Cr(VI) ions by using the high-performance liquid chromatography (HPLC) at wavelength 650 nm, a stationary phase consists of reversed phase column (Nucleosil phenyl column; 250 x 4.6 mm, 5 μm), and a mobile phase consists of 0.001 M di-(2-ethylhexyl) phosphoric acid (DEHPA) in methanol:water (70:30 v/v). The retention times were 7.0 and 8.5 min, for the Cr(III) and Cr(VI), respectively. The exchange capacity of Cr(III) was quantified (2.1 meq/g) onto the TX-100CeP. (author)

  19. Electrochemical characterization of Si in tetra-methyl ammonium hydroxide (TMAH) and TMAH:Triton-X-100 solutions under white light effects

    Science.gov (United States)

    Conway, Elizabeth M.; Cunnane, Vincent J.

    2002-03-01

    An experimental study of the electrochemical characteristics of the silicon/tetra-methyl ammonium hydroxide (TMAH) junction under dark and white light conditions are investigated for both n- and p-type Si. The presence of Triton-X-100 (TX100) in the TMAH solution under white light conditions is also studied. Cyclic voltammetry (CV) and ex situ atomic force microscopy (AFM) are employed to study the white light effects on the etching characteristics of silicon in TMAH and TMAH:TX100. It was found that the passivation peak potential shifted significantly for both n- and p-type Si under white light conditions. The positions of the flatband potential for n- and p-type Si were predicted by CV under illumination. Finally, etch rate studies and preliminary surface roughness measurements were performed on p(100) Si in TMAH under both dark and white light conditions. These latter studies concluded that a reduction in the vertical surface roughness occurred in the presence of white light.

  20. Impact of ultrasonication time on elution of super heavy oil and its biomarkers from aging soils using a Triton X-100 micellar solution

    International Nuclear Information System (INIS)

    Ji Guodong; Zhou Guohui

    2010-01-01

    An ultrasound-enhanced elution system with Triton X-100 solution was used to remediate aging soils contaminated with super heavy oil. We used GC/MS, SEM, and X-ray diffraction (XRD) to analyze the effect of ultrasonic time (0-1800 s) on the elution of super heavy oil and its three characteristic biomarkers (C 26-34 17α 25-norhopanes, C 26-28 triaromatic steroid [TAS], and C 27-29 methyl triaromatic steroid [MTAS]). The oil and biomarkers remaining in the treated soils followed similar second-order functions with increasing ultrasonication times. Biomarker elution was closely related to carbon numbers in the marker. For C 26-34 17α 25-norhopanes, the smaller molecules were more readily eluted during 0-360 s ultrasound. This trend was reversed upon application of ultrasound during 1080-1800 s, with improved elution of larger molecules and elution followed a similar second-order function. For C 26-28 TAS, smaller molecules were more readily eluted but the elution of larger molecules followed a similar second-order function. For C 27-29 MTAS, elution of larger molecules was close to that of C 26-34 17α 25-norhopanes. Results of SEM and XRD indicated that the mineral and chemical compositions of soils eluted at ultrasonication times of 1080-1800 s closely resembled clean soils.

  1. Picosecond studies of excitation transport in a finite volume: The clustered transport system octadecyl rhodamine B in triton X-100 micelles

    International Nuclear Information System (INIS)

    Ediger, M.D.; Domingue, R.P.; Fayer, M.D.

    1984-01-01

    A detailed experimental and theoretical examination of electronic excited state transport in the finite volume system, octadecyl rhodamine B molecules in triton X-100 micelles, is presented. Picosecond fluorescence mixing and transient grating techniques were used to examine systems in which the average number of chromophores per micelle ranged from 0.1 to 11. Because of the clustering of chromophores in the small micelles, the energy transport observed is extremely efficient. A statistical mechanical theory, based on a density expansion with a Pade approximant, is developed for donor--donor transport on a spherical surface. This theory accurately accounts for the experimental data with only the micelle radius as an adjustable parameter. The radius obtained from this procedure is in good agreement with determinations by other methods. This demonstrates that quantitative information about the spatial extent of chromophore distributions in small volumes can be obtained when appropriate finite volume energy transport theories are employed. It is shown that theories developed for infinite volumes are not applicable to systems such as the ones considered here. Finally the partitioning of rhodamine B and octadecyl rhodamine B between aqueous and micellar phases is measured, and lifetimes and rotation times are reported

  2. Improvement on D-xylose to Xylitol Biotransformation by Candida guilliermondii Using Cells Permeabilized with Triton X-100 and Selected Process Conditions.

    Science.gov (United States)

    Cortez, Daniela Vieira; Mussatto, Solange I; Roberto, Inês Conceição

    2016-11-01

    Cells of Candida guilliermondii permeabilized with Triton X-100 were able to efficiently produce xylitol from a medium composed only by D-xylose and MgCl 2 ·6H 2 O in potassium phosphate buffer, at 35 °C and pH 6.5. Under these conditions, the results were similar to those obtained when cofactor and co-substrate or nutrients were added to the medium (about 95 % D-xylose was assimilated producing 42 g/L of xylitol, corresponding to 0.80 g/g yield and 2.65 g/L h volumetric productivity). Furthermore, the permeabilized cells kept the D-xylose assimilation in about 90 % and the xylitol production in approx. 40 g/L during three bioconversion cycles of 16 h each. These values are highly relevant when compared to others reported in the literature using enzyme technology and fermentative process, thereby demonstrating the effectiveness of the proposed method. The present study reveals that the use of permeabilized cells is an interesting alternative to obtain high xylitol productivity using low cost medium formulation. This approach may allow the future development of xylitol production from xylose present in lignocellulosic biomass, with additional potential for implementation in biorefinery strategies.

  3. Synergistic Cardioprotective Effects of Combined Chromium Picolinate and Atorvastatin Treatment in Triton X-100-Induced Hyperlipidemia in Rats: Impact on Some Biochemical Markers.

    Science.gov (United States)

    Shafik, Noha M; Baalash, Amal; Ebeid, Abla M

    2017-12-01

    Hyperlipidemia is one of the major risk factors for atherosclerosis and ischemic heart disease. Chromium (Cr) mineral is playing a crucial role in glucose and lipid homeostasis. The aim of this study was to evaluate the protective effects of combined chromium picolinate (CrPic) and atorvastatin treatment against hyperlipidemia-induced cardiac injury. Seventy-five male albino rats were divided into five groups (15 rats each). Hyperlipidemia was induced by intraperitoneal injection of a single dose of Triton X-100 (300 mg/kg body weight (b.w) (group ІІ). Treatment of hyperlipidemic rats was induced by daily administration of CrPic at a dose of 200 μg/kg b.w/day (group ІІІ), atorvastatin at a dose of 10 mg/kg/day (group IV), and combined treatment with both (group V) by gavage for 7 days. At the end of experiment, serum and heart tissues were obtained. Hyperlipidemia was confirmed by histopathology of heart tissues, marked serum dyslipidemia, increased atherogenic indices, and values of ischemia-modified albumin. In addition to increased values of proprotein convertase subtilisin/kexin type 9, activity of 3-hydroxy-3-methylglutaryl coenzyme A reductase enzyme and high relative expression levels of pentraxin-3 were observed. However, paraoxonase-1 activity was markedly decreased in the hyperlipidemic group. Significant improvement in all assessed parameters was observed in the rat group treated with both CrPic and atorvastatin. It can be concluded that combined CrPic and atorvastatin treatments had synergistic cardioprotective effects against hyperlipidemia which may be through modulating atherosclerosis as well as cardiac and aortic damage and/or activation of anti-inflammatory and anti-oxidant pathways, thus reversing endothelial dysfunction.

  4. Separation of Methylene Blue Dye from Aqueous Solution Using Triton X-114 Surfactant

    Directory of Open Access Journals (Sweden)

    Arunagiri Appusamy

    2014-01-01

    Full Text Available In this study, the interaction energy between Triton X-114 surfactant + methylene blue or water and methylene blue + water was investigated using Hartree-Fock (HF theory with 6-31G* basis set. The results of structures and interaction energies show that these complexes have good physical and chemical interactions at atom and molecular levels. However, the Triton X-114 surfactant + methylene blue complex shows stronger molecular interaction compared to other complexes systems. The order of the interaction energy is 4303.472023 (Triton X-114 surfactant + water > -1222.962 (methylene blue + water > -3573.28 (Triton X-114 surfactant + methylene blue kJ·mole−1. Subsequently, the cloud point extraction was carried out for 15 ppm of methylene blue in a mixture at 313.15 and 323.15 K over the surfactant concentration range from 0.01 M to 0.1 M. From the measured data, the excess molar volume was calculated for both phases. The results show a positive deviation in the dilute phase and a negative deviation in the surfactant rich phase. It is confirmed that the interaction between Triton X-114 and methylene blue is stronger than other complex systems due to the presence of chemical and structural orientation. The concentration of dyes and surfactant in the feed mixture and temperature effect in both phases has been studied. In addition, the thermodynamics feasibility and efficiency of the process have also been investigated.

  5. Monitoring corrosion and corrosion control of iron in HCl by non-ionic surfactants of the TRITON-X series - Part II. Temperature effect, activation energies and thermodynamics of adsorption

    International Nuclear Information System (INIS)

    Amin, Mohammed A.; Ahmed, M.A.; Arida, H.A.; Arslan, Taner; Saracoglu, Murat; Kandemirli, Fatma

    2011-01-01

    Research highlights: → TX-305 exhibits inhibiting properties for iron corrosion more than TX-165 and TX 100. → Inhibition efficiency increases with temperature, suggesting chemical adsorption. → The three tested surfactants act as mixed-type inhibitors with cathodic predominance. → Validation of corrosion rates measured by Tafel extrapolation method is confirmed. - Abstract: The inhibition characteristics of non-ionic surfactants of the TRITON-X series, namely TRITON-X-100 (TX-100), TRITON-X-165 (TX-165) and TRITON-X-305 (TX-305), on the corrosion of iron was studied in 1.0 M HCl solutions as a function of inhibitor concentration (0.005-0.075 g L -1 ) and solution temperature (278-338 K). Measurements were conducted based on Tafel extrapolation method. Electrochemical frequency modulation (EFM), a non-destructive corrosion measurement technique that can directly give values of corrosion current without prior knowledge of Tafel constants, is also presented. Experimental corrosion rates determined by the Tafel extrapolation method were compared with corrosion rates obtained by the EFM technique and an independent method of chemical analysis. The chemical method of confirmation of the corrosion rates involved determination of the dissolved cation, using ICP-AES (inductively coupled plasma atomic emission spectrometry). The aim was to confirm validation of corrosion rates measured by the Tafel extrapolation method. Results obtained showed that, in all cases, the inhibition efficiency increased with increase in temperature, suggesting that chemical adsorption occurs. The adsorptive behaviour of the three surfactants followed Temkin-type isotherm. The standard free energies of adsorption decreased with temperature, reflecting better inhibition performance. These findings confirm chemisorption of the tested inhibitors. Thermodynamic activation functions of the dissolution process were also calculated as a function of each inhibitor concentration. All the results

  6. Effect of Surfactants on Plasmid DNA Stability and Release from ...

    African Journals Online (AJOL)

    Purpose: To evaluate the effect of surfactants on plasmid DNA during preparation and release from polylactic glycolide (PLGA) microspheres. Methods: Various surfactants, both ionic and non-ionic (Span, Tween, Triton X100, cetyltrimethylammonium bromide and sodium dodecyl sulphate), were added during the ...

  7. Surfactant assisted electrodeposition of MnO{sub 2} thin films: Improved supercapacitive properties

    Energy Technology Data Exchange (ETDEWEB)

    Dubal, D.P. [Thin Film Physics Laboratory, Department of Physics, Shivaji University, Kolhapur 416004 (M.S.) (India); School of Materials Science and Engineering, Gwangju Institute of Science and Technology, 261 Cheomdan-gwagiro, Buk-gu, Gwangju 500-712 (Korea, Republic of); Kim, W.B. [School of Materials Science and Engineering, Gwangju Institute of Science and Technology, 261 Cheomdan-gwagiro, Buk-gu, Gwangju 500-712 (Korea, Republic of); Lokhande, C.D., E-mail: l_chandrakant@yahoo.com [Thin Film Physics Laboratory, Department of Physics, Shivaji University, Kolhapur 416004 (M.S.) (India)

    2011-10-13

    Highlights: > Effect of Triton X-100 on physico-chemical properties of MnO{sub 2} films. > High supercapacitance of 345 F g{sup -1}. > Charge-discharge, impedance spectroscopy. - Abstract: In order to obtain a high specific capacitance, MnO{sub 2} thin films have been electrodeposited in the presence of a neutral surfactant (Triton X-100). These films were further characterized by means of X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy (FESEM) and contact angle measurement. The XRD studies revealed that the electrodeposited MnO{sub 2} films are amorphous and addition of Triton X-100 does not change its amorphous nature. The electrodeposited films of MnO{sub 2} in the presence of the Triton X-100 possess greater porosity and hence greater surface area in relation to the films prepared in the absence of the surfactant. Wettability test showed that the MnO{sub 2} film becomes superhydrophilic from hydrophilic due to Triton X-100. Supercapacitance properties of MnO{sub 2} thin films studied by cyclic voltammetry, galvanostatic charge-discharge cycling and impedance spectroscopy showed maximum supercapacitance for MnO{sub 2} films deposited in presence of Triton X-100 is 345 F g{sup -1}.

  8. Surfactant assisted electrodeposition of MnO2 thin films: Improved supercapacitive properties

    International Nuclear Information System (INIS)

    Dubal, D.P.; Kim, W.B.; Lokhande, C.D.

    2011-01-01

    Highlights: → Effect of Triton X-100 on physico-chemical properties of MnO 2 films. → High supercapacitance of 345 F g -1 . → Charge-discharge, impedance spectroscopy. - Abstract: In order to obtain a high specific capacitance, MnO 2 thin films have been electrodeposited in the presence of a neutral surfactant (Triton X-100). These films were further characterized by means of X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy (FESEM) and contact angle measurement. The XRD studies revealed that the electrodeposited MnO 2 films are amorphous and addition of Triton X-100 does not change its amorphous nature. The electrodeposited films of MnO 2 in the presence of the Triton X-100 possess greater porosity and hence greater surface area in relation to the films prepared in the absence of the surfactant. Wettability test showed that the MnO 2 film becomes superhydrophilic from hydrophilic due to Triton X-100. Supercapacitance properties of MnO 2 thin films studied by cyclic voltammetry, galvanostatic charge-discharge cycling and impedance spectroscopy showed maximum supercapacitance for MnO 2 films deposited in presence of Triton X-100 is 345 F g -1 .

  9. Preparation, Characterization and Performance Studies of Active PVDF Ultrafiltration-Surfactants Membranes Containing PVP as Additive

    International Nuclear Information System (INIS)

    Nur Izzah Md Fadilah; Abdul Rahman Hassan

    2016-01-01

    The role of surfactants in the formation of active Poly(vinylidene fluoride) (PVDF) ultrafiltration (AUF) membranes was studied. The effect combination of surfactants that are Sodium dodecyl sulfate (SDS)/ Tween 80 and Tween 80/ Triton X-100 formulations on performance and morphological structures were investigated for the first time. The influence of surfactants blends on the membrane pores was also examined. Experimental data showed that combination of Tween 80/ Triton X-100 give the highest BSA permeation flux with a value of 285.51 Lm -2 h -1 . With combination of SDS/ Tween 80, the AUF membrane showed the highest protein rejection up to 93 % and 79 % for Bovine Serum Albumin (BSA) and Egg Albumin (EA), respectively. Moreover, membranes characterization demonstrated that the addition of SDS/ Tween 80 and Tween 80/ Triton X-100 were found to affect the performance, surface morphologies and membrane pores of AUF PVDF membranes. (author)

  10. Mobilization of arsenic from contaminated sediment by anionic and nonionic surfactants.

    Science.gov (United States)

    Liang, Chuan; Peng, Xianjia

    2017-06-01

    The increasing manufacture of surfactants and their wide application in industry, agriculture and household detergents have resulted in large amounts of surfactant residuals being discharged into water and distributed into sediment. Surfactants have the potential to enhance arsenic mobility, leading to risks to the environment and even human beings. In this study, batch and column experiments were conducted to investigate arsenic mobilization from contaminated sediment by the commercial anionic surfactants sodium dodecylbenzenesulfonate (SDBS), sodium dodecyl sulfate (SDS), sodium laureth sulfate (AES) and nonionic surfactants phenyl-polyethylene glycol (Triton X-100) and polyethylene glycol sorbitan monooleate (Tween-80). The ability of surfactants to mobilize arsenic followed the order AES>SDBS>SDS≈Triton X-100>Tween 80. Arsenic mobilization by AES and Triton X-100 increased greatly with the increase of surfactant concentration and pH, while arsenic release by SDBS, SDS and Tween-80 slightly increased. The divalent ion Ca 2+ caused greater reduction of arsenic mobilization than Na + . Sequential extraction experiments showed that the main fraction of arsenic mobilized was the specifically adsorbed fraction. Solid phase extraction showed that arsenate (As(V)) was the main species mobilized by surfactants, accounting for 65.05%-77.68% of the total mobilized arsenic. The mobilization of arsenic was positively correlated with the mobilization of iron species. The main fraction of mobilized arsenic was the dissolved fraction, accounting for 70% of total mobilized arsenic. Copyright © 2016. Published by Elsevier B.V.

  11. Enhanced production of pigments by addition of surfactants in submerged fermentation of Monascus purpureus H1102.

    Science.gov (United States)

    Wang, Yonghui; Zhang, Bobo; Lu, Liping; Huang, Yan; Xu, Ganrong

    2013-10-01

    The production of pigments by Monascus spp. has attracted increasing attention. Modification of the cell membrane structure by addition of surfactants has proved to be effective for the secretion of intracellular metabolites. Hence in this study the effects and underlying mechanism of surfactants on the production of pigments in submerged fermentation of Monascus purpureus H1102 were systematically investigated. Various surfactants exerted significant but different impacts on the biomass and production of pigments. The maximum production of pigment (304.3 U mL(-1) ) and highest extracellular/intracellular pigment ratio (1.46) were achieved when 15 g L(-1) Triton X-100 was added at 24 h of fermentation, corresponding to significant increases of 88.4 and 240% respectively compared with the control. Meanwhile, the concentration of citrinin (0.94 mg L(-1) ) was 20.6% lower than that of the control. A further study on the fatty acid composition of M. purpureus H1102 showed that the unsaturated/saturated fatty acid ratio and the index of unsaturated fatty acid increased significantly with the addition of Triton X-100. The addition of surfactant Triton X-100 could greatly enhance the production of pigment. It was suggested that Triton X-100 facilitated the secretion of intracellular pigment and therefore enhanced pigment production accordingly. © 2013 Society of Chemical Industry.

  12. Effect of surfactants on the spectrofluorimetric properties of zearalenone

    International Nuclear Information System (INIS)

    Appell, Michael; Bosma, Wayne B.

    2011-01-01

    The chemiluminescent properties of the estrogenic mycotoxin zearalenone in the presence of aqueous micellar media were investigated using steady state fluorescence techniques. Micelles of surfactants sodium dodecyl sulfate (SDS), hexadecyltrimethylammonium bromide (CTAB), and non-ionic Triton X-100 enhanced the fluorescence intensity of zearalenone in aqueous solutions. The binding constants have been determined and indicate zearalenone has the highest affinity for Triton X-100, followed by CTAB, and then by SDS. The encapsulation of zearalenone by the micelles studied is spontaneous and exothermic. The selective microenvironments provided by organized micellar systems offer an attractive medium to modulate fluorescence detection of zearalenone. - Highlights: → Surfactants can selectively modulate the fluorescence detection of zearalenone. → Binding studies provide information on the zearalenone-surfactant interactions. → Fluorescence intensity of zearalenone is related to the micelle microenvironment.

  13. Role of a non-ionic surfactant in direct electron transfer-type bioelectrocatalysis by fructose dehydrogenase

    International Nuclear Information System (INIS)

    Kawai, Shota; Yakushi, Toshiharu; Matsushita, Kazunobu; Kitazumi, Yuki; Shirai, Osamu; Kano, Kenji

    2015-01-01

    Highlights: • Addition of Triton ® X-100 (1%) completely quenches the FDH-catalyzed current at hydrophobic electrode, but causes only small competitive effect at hydrophilic electrode. • Quartz crystal microbalance measurements support the adsorption of FDH and Triton ® X-100 on both of the electrodes. • The surfactant forms a monolayer on the hydrophobic electrode and FDH adsorbs on the surfactant monolayer. • The surfactant forms a bilayer on the hydrophilic electrode and FDH is embedded in the bilayer to communicate with the electrode. - ABSTRACT: A heterotrimeric membrane-bound fructose dehydrogenase (FDH) from Gluconobacter japonicus NBRC3260 contains FAD in subunit I and three heme C moieties in subunit II as the redox centers, and is one of the direct electron transfer (DET)-type redox enzymes. FDH-catalyzed current density of fructose oxidation at hydrophilic mercaptoethanol (MEtOH)-modified Au electrode is much larger than that at hydrophobic mercaptoethane (MEtn)-modified Au electrode. Addition of a non-ionic surfactant Triton ® X-100 (1%) completely quenches the catalytic current at the MEtn-modified Au electrode, while only small competitive effect is observed at the MEtOH-modified Au electrode. Quartz crystal microbalance measurements support the adsorption of FDH and Triton ® X-100 on both of the modified electrodes. We propose a model to explain the phenomenon as follows. The surfactant forms a monolayer on the hydrophobic MEtn-modified electrode with strong hydrophobic interaction, and FDH adsorbs on the surface of the surfactant monolayer. The monolayer inhibits the electron transfer from FDH to the electrode. On the other hand, the surfactant forms a bilayer on the hydrophilic MEtOH-modified electrode. The interaction between the surfactant bilayer and the hydrophilic electrode is relatively weak so that FDH replaces the surfactant and is embedded in the bilayer to communicate electrochemically with the hydrophilic electrode

  14. Monitoring corrosion and corrosion control of iron in HCl by non-ionic surfactants of the TRITON-X series - Part III. Immersion time effects and theoretical studies

    International Nuclear Information System (INIS)

    Amin, Mohammed A.; Ahmed, M.A.; Arida, H.A.; Kandemirli, Fatma; Saracoglu, Murat; Arslan, Taner; Basaran, Murat A.

    2011-01-01

    Graphical abstract: . Display Omitted Research highlights: → The inhibition effect of TX-100, TX-165 and TX-305 on iron corrosion in 1.0 M HCl was studied. → TX-305 inhibited iron corrosion more effectively than TX-100 and TX-165. → In most cases, inhibition efficiency increased with time during the first 60 min of immersion, then decreased. → Calculated quantum chemical parameters confirmed the experimental inhibition efficiencies of the tested surfactants. - Abstract: The inhibition performance of three selected non-ionic surfactants of the TRITON-X series, namely TRITONX-100 (TX-100), TRITON-X-165 (TX-165) and TRITON-X-305 (TX-305), on the corrosion of iron was studied in 1.0 M HCl solutions as a function of inhibitor concentration (0.01-0.20 g L -1 ) and immersion time (0.0-8 h) at 298 K. Measurements were conducted based on Tafel polarization, LPR and impedance studies. At high frequencies, the impedance spectrum showed a depressed capacitive loop in the complex impedance plane, whose diameter is a function of the immersion time and the type and concentration of the introduced surfactant. In all cases, an inductive loop was observed in the low frequency and this could be attributed to the adsorption behavior. The inhibition efficiency increased with immersion time, reached a maximum and then decreased. This was attributed to the orientation change of adsorbed surfactant molecules. TX-305 inhibited iron corrosion more effectively than TX-100 and TX-165. The frontier orbital energies, the energy gap between frontier orbitals, dipole moments (μ), charges on the C and O atoms, the polarizabilities, and the quantum chemical descriptors were calculated. The quantum chemical calculation results inferred that for the HOMO representing the condensed Fukui function for an electrophilic attack (f k + ), the contributions belong to the phenyl group and the oxygen atom attached to the phenyl group for each tested surfactant. Quantitative structure

  15. Determination of some solubilization parameters with surfactants of egg-yolk lecithin multilamellar vesicles by static light-scattering measurements

    OpenAIRE

    Hobai, St.; Fazakas, Zita

    2000-01-01

    Effective surfactant:phospholipid ratios (i.e. molar ratios in the mixed aggregates, vesicles or micelles) have been determined by static light-scattering for the interaction of egg-yolk lecithin (EYL) multilamellar vesicles (MLV) with Triton X-100 (TX-100), sodium deoxycholate (DOCNa) and cetyltrimethylammonium bromide (CTMB). The suspension of MLV-EYL was mixed with appropriate volumes of surfactant solution and was left overnight to reaches thermodynamic equilibrium. Rectan-gular optic dif...

  16. Surfactant use with nitrate-based bioremediation

    International Nuclear Information System (INIS)

    Wilson, B.H.; Hutchins, S.R.; West, C.C.

    1995-01-01

    This study presents results of an initial survey on the effect of six surfactants on the biodegradation of petroleum hydrocarbons in bioremediation applications using nitrate as the electron acceptor. Aquifer material from Park City, Kansas, was used for the study. The three atomic surfactants chosen were Steol CS-330, Dowfax 8390 and sodium dodecylbenzene sulfonate (SDBS); the three nonionic surfactants were T-MAZ-60, Triton X-100, and Igepal CO-660. Both Steol CS-330 and T-MAZ-60 biodegraded under denitrifying conditions. The Steol inhibited biodegradation of benzene, toluene, ethylbenzene, xylenes, and trimethylbenzenes (BTEXTMB). Only toluene was rapidly degraded in the presence of T-MAZ-60. Biodegradation of all compounds, including toluene, appears to be inhibited by Dowfax 8390 and SDBS. No biodegradation of Dowfax 8390 or SDBS was observed. SDBS inhibited denitrification, but Dowfax 8390 did not. For the microcosms containing Triton X-100 or Igepal CO-660, removal of toluene, ethylbenzene, m-xylene, 1,3,5-TMB, and 1,2,4-TMB were similar to their removals in the no-surfactant treatment. These two surfactants did not biodegrade, did not inhibit biodegradation of the alkylbenzenes, and did not inhibit denitrification. Further studies are continuing with aquifer material from Eglin Air Force Base

  17. Perstraction of Intracellular Pigments through Submerged Fermentation of Talaromyces spp. in a Surfactant Rich Media: A Novel Approach for Enhanced Pigment Recovery

    Directory of Open Access Journals (Sweden)

    Lourdes Morales-Oyervides

    2017-06-01

    Full Text Available A high percentage of the pigments produced by Talaromyces spp. remains inside the cell, which could lead to a high product concentration inhibition. To overcome this issue an extractive fermentation process, perstraction, was suggested, which involves the extraction of the intracellular products out of the cell by using a two-phase system during the fermentation. The present work studied the effect of various surfactants on secretion of intracellular pigments produced by Talaromyces spp. in submerged fermentation. Surfactants used were: non-ionic surfactants (Tween 80, Span 20 and Triton X-100 and a polyethylene glycerol polymer 8000, at different concentrations (5, 20, 35 g/L. The highest extracellular pigment yield (16 OD500nm was reached using Triton X-100 (35 g/L, which was 44% higher than the control (no surfactant added. The effect of addition time of the selected surfactant was further studied. The highest extracellular pigment concentration (22 OD500nm was achieved when the surfactant was added at 120 h of fermentation. Kinetics of extracellular and intracellular pigments were examined. Total pigment at the end of the fermentation using Triton X-100 was 27.7% higher than the control, confirming that the use of surfactants partially alleviated the product inhibition during the pigment production culture.

  18. Surfactant-dependent macrophage response to polypyrrole-based coatings electrodeposited on Ti6Al7Nb alloy

    Energy Technology Data Exchange (ETDEWEB)

    Mindroiu, Mihaela [University Polytechnica of Bucharest, Faculty of Applied Chemistry and Materials Science, 1-7 Polizu, 011061, Bucharest (Romania); Ion, Raluca [University of Bucharest, Department of Biochemistry and Molecular Biology, 91-95 Spl. Independentei, 050095, Bucharest (Romania); Pirvu, Cristian [University Polytechnica of Bucharest, Faculty of Applied Chemistry and Materials Science, 1-7 Polizu, 011061, Bucharest (Romania); Cimpean, Anisoara, E-mail: anisoara.cimpean@bio.unibuc.ro [University of Bucharest, Department of Biochemistry and Molecular Biology, 91-95 Spl. Independentei, 050095, Bucharest (Romania)

    2013-08-01

    In this study, polypyrrole (PPy) films were successfully synthesized on Ti6Al7Nb alloy by potentiostatic polymerization in the presence of poly(sodium 4-styrenesulfonate) (NaPSS), t-octylphenoxy polyethoxyethanol (Triton X-100) and N-dodecyl-β-D-maltoside (DM) surfactants. Atomic force microscopy (AFM) analysis of the PPy/surfactant composite films revealed a granular structure characterized by a lower surface roughness than un-modified PPy films. The results demonstrated that addition of surfactants, namely Triton X-100 and DM, can improve electrochemical film stability and corrosion resistance. Further, Triton X-100 enhanced the adhesive strength of PPy films to the substrate. The surfactant type also showed a great influence on the surface wettability, the highest hydrophilic character being observed in the case of PPy/PSS film. Few studies have been devoted to the elucidation of inflammatory cell response to PPy-based materials. Therefore, RAW 264.7 macrophages were cultured on PPy-surfactant films to determine whether they elicit a differential cell behavior in terms of cell adhesion, proliferation, cellular morphology and cytokine secretion. Our results highlight the dependence of macrophage response on the surfactants used in the pyrrole polymerization process and suggest that the immune response to biomaterials coated with PPy films might be controlled by the choice of surfactant molecules. Highlights: • We electrodeposited polypyrrole films on Ti6Al7Nb alloy using three surfactants. • Differences in electrostability and wettability of polypyrrole films were found. • Triton X increased and NaPSS decreased the adhesion of polypyrrole films to Ti6Al7Nb. • Cytoskeletal architecture and macrophage activation were affected by surfactants. • The hydrophilic PPy/PSS coating elicited the lowest inflammatory response.

  19. Surfactant-dependent macrophage response to polypyrrole-based coatings electrodeposited on Ti6Al7Nb alloy

    International Nuclear Information System (INIS)

    Mindroiu, Mihaela; Ion, Raluca; Pirvu, Cristian; Cimpean, Anisoara

    2013-01-01

    In this study, polypyrrole (PPy) films were successfully synthesized on Ti6Al7Nb alloy by potentiostatic polymerization in the presence of poly(sodium 4-styrenesulfonate) (NaPSS), t-octylphenoxy polyethoxyethanol (Triton X-100) and N-dodecyl-β-D-maltoside (DM) surfactants. Atomic force microscopy (AFM) analysis of the PPy/surfactant composite films revealed a granular structure characterized by a lower surface roughness than un-modified PPy films. The results demonstrated that addition of surfactants, namely Triton X-100 and DM, can improve electrochemical film stability and corrosion resistance. Further, Triton X-100 enhanced the adhesive strength of PPy films to the substrate. The surfactant type also showed a great influence on the surface wettability, the highest hydrophilic character being observed in the case of PPy/PSS film. Few studies have been devoted to the elucidation of inflammatory cell response to PPy-based materials. Therefore, RAW 264.7 macrophages were cultured on PPy-surfactant films to determine whether they elicit a differential cell behavior in terms of cell adhesion, proliferation, cellular morphology and cytokine secretion. Our results highlight the dependence of macrophage response on the surfactants used in the pyrrole polymerization process and suggest that the immune response to biomaterials coated with PPy films might be controlled by the choice of surfactant molecules. Highlights: • We electrodeposited polypyrrole films on Ti6Al7Nb alloy using three surfactants. • Differences in electrostability and wettability of polypyrrole films were found. • Triton X increased and NaPSS decreased the adhesion of polypyrrole films to Ti6Al7Nb. • Cytoskeletal architecture and macrophage activation were affected by surfactants. • The hydrophilic PPy/PSS coating elicited the lowest inflammatory response

  20. Influences and mechanisms of surfactants on pyrene biodegradation based on interactions of surfactant with a Klebsiella oxytoca strain.

    Science.gov (United States)

    Zhang, Dong; Zhu, Lizhong; Li, Feng

    2013-08-01

    Surfactant-enhanced bioremediation has been proposed as a promising technology for the treatment of organic polluted soils; however its application has been hindered by the controversial influences and mechanisms of surfactants on the biodegradation of hydrophobic organic compounds. To address this problem, effects of five surfactants on the sorption and biodegradation of pyrene by Klebsiella oxytoca PYR-1, as well as their interactions with bacterial cell surface and membrane lipids were investigated. We found that surfactants enhanced or inhibited pyrene biodegradation depending on their effects on the sorption of pyrene onto bacterial cell, which occurred mainly through modifying cell surface hydrophobicity (such as Tween series surfactants) or disrupting bacterial membrane (such as Triton X-100), respectively. A relatively high positive correlation (Psurfactant, indicating that surfactant-induced sorption played the dominant role during pyrene biodegradation. Copyright © 2013 Elsevier Ltd. All rights reserved.

  1. DDT uptake by arbuscular mycorrhizal alfalfa and depletion in soil as influenced by soil application of a non-ionic surfactant

    International Nuclear Information System (INIS)

    Wu Naiying; Zhang Shuzhen; Huang Honglin; Shan Xiaoquan; Christie, Peter; Wang Youshan

    2008-01-01

    A greenhouse pot experiment was conducted to investigate the colonization of alfalfa roots by the arbuscular mycorrhizal (AM) fungus Glomus etunicatum and application of the non-ionic surfactant Triton X-100 on DDT uptake by alfalfa and depletion in soil. Mycorrhizal colonization led to an increase in the accumulation of DDT in roots but a decrease in shoots. The combination of AM inoculation and Triton X-100 application enhanced DDT uptake by both the roots and shoots. Application of Triton X-100 gave much lower residual concentrations of DDT in the bulk soil than in the rhizosphere soil or in the bulk soil without Triton X-100. AM colonization significantly increased bacterial and fungal counts and dehydrogenase activity in the rhizosphere soil. The combined AM inoculation of plants and soil application of surfactant may have potential as a biotechnological approach for the decontamination of soil polluted with DDT. - Combined colonization of alfalfa roots by an arbuscular mycorrhizal fungus and addition of non-ionic surfactant to the soil promoted root and shoot uptake and soil dissipation of DDT

  2. Surfactant-enhanced remediation of a trichloroethene-contaminated aquifer. 2. Transport of TCE

    Science.gov (United States)

    Sahoo, D.; Smith, J.A.; Imbrigiotta, T.E.; Mclellan, H.M.

    1998-01-01

    Field studies were conducted under an induced gradient in a trichloroethene (TCE)-contaminated aquifer at Picatinny Arsenal, NJ, to study (a) the rate-limited desorption of TCE from aquifer sediments to water and (b) the effect of a surfactant (Triton X-100) on the desorption and transport of TCE. Clean water was injected into the contaminated aquifer for 206 day. Triton X-100 was added for a 36-day period (days 36-71 from the start of clean water injection). The effect of Triton X-100 on the desorption and transport of TCE in the field was examined by observing the concentrations of these two solutes in four monitoring wells 3-9 m from the injection wells. These data show a small but discernible increase in the TCE concentration in two of the wells corresponding approximately to the time when surfactant reaches the wells; in the other two monitoring wells, the increase in TCE concentration is negligible. A solute transport model that assumes local sorption equilibrium and used a laboratory-derived distribution coefficient could not adequately describe TCE desorption and transport observed in the aquifer. Two model formulations that accounted for rate-limited sorption - two-site and multisite models - fit the data well. TCE concentrations after surfactant injection were underpredicted by the models unless mass transfer rate was increased to account for the effect of surfactant on the rate of TCE desorption. The concentration data from the two wells and the model analysis suggest that the rate of TCE desorption is increased (by approximately 30%) as a result of Triton X-100 injection.Field studies were conducted under an induced gradient in a trichloroethene (TCE)-contaminated aquifer at Picatinny Arsenal, NJ, to study (a) the rate-limited desorption of TCE from aquifer sediments to water and (b) the effect of a surfactant (Triton X-100) on the desorption and transport of TCE. Clean water was injected into the contaminated aquifer for 206 day. Triton X-100 was added

  3. Polydiacetylene sensor interaction with food sanitizers and surfactants.

    Science.gov (United States)

    Zhang, Yueyuan; Northcutt, Julie; Hanks, Tim; Miller, Ian; Pennington, Bill; Jelinek, Raz; Han, Inyee; Dawson, Paul

    2017-04-15

    Polydiacetylene (PDA) vesicles are of interest as biosensors, particularly for pathogenic bacteria. As part of a food monitoring system, interaction with food sanitizers/surfactants was investigated. PDA vesicles were prepared by inkjet-printing, photopolymerized and characterized by dynamic light scattering (DLS) and UV/Vis spectroscopy. The optical response of PDA vesicles at various concentrations verses a fixed sanitizer/surfactant concentration was determined using a two variable factorial design. Sanitizer/surfactant response at various concentrations over time was also measured. Results indicated that only Vigilquat and TritonX-100 interacted with PDA vesicles giving visible colour change out of 8 sanitizers/surfactants tested. PDA vesicle concentration, sanitizer/surfactant concentration, and time all had a significant (P<0.0001) effect on colour change. As they are highly sensitive to the presence of Vigilquat and TritonX-100, PDA sensors could be used to detect chemical residues as well as for detection of various contaminants in the food industry. Copyright © 2016. Published by Elsevier Ltd.

  4. Interactions between Surfactants in Solution and Electrospun Protein Fibers: Effects on Release Behavior and Fiber Properties

    DEFF Research Database (Denmark)

    Boutrup Stephansen, Karen; García-Díaz, María; Jessen, Flemming

    2016-01-01

    , and drug delivery. In the present study, we present a systematic investigation of how surfactants and proteins, as physiologically relevant components, interact with insulin-loaded fish sarcoplasmic protein (FSP) electrospun fibers (FSP-Ins fibers) in solution and thereby affect fiber properties...... such as accessible surface hydrophilicity, physical stability, and release characteristics of an encapsulated drug. Interactions between insulin-loaded protein fibers and five anionic surfactants (sodium taurocholate, sodium taurodeoxycholate, sodium glycocholate, sodium glycodeoxycholate, and sodium dodecyl sulfate......), a cationic surfactant (benzalkonium chloride), and a neutral surfactant (Triton X-100) were studied. The anionic surfactants increased the insulin release in a concentration-dependent manner, whereas the neutral surfactant had no significant effect on the release. Interestingly, only minute amounts...

  5. Bubble-size distributions produced by wall injection of air into flowing freshwater, saltwater and surfactant solutions

    Science.gov (United States)

    Winkel, Eric S.; Ceccio, Steven L.; Dowling, David R.; Perlin, Marc

    2004-12-01

    As air is injected into a flowing liquid, the resultant bubble characteristics depend on the properties of the injector, near-wall flow, and flowing liquid. Previous research has shown that near-wall bubbles can significantly reduce skin-friction drag. Air was injected into the turbulent boundary layer on a test section wall of a water tunnel containing various concentrations of salt and surfactant (Triton-X-100, Union Carbide). Photographic records show that the mean bubble diameter decreased monotonically with increasing salt and surfactant concentrations. Here, 33 ppt saltwater bubbles had one quarter, and 20 ppm Triton-X-100 bubbles had one half of the mean diameter of freshwater bubbles.

  6. Surfactant media for constant-current coulometry. Application for the determination of antioxidants in pharmaceuticals

    Energy Technology Data Exchange (ETDEWEB)

    Ziyatdinova, Guzel, E-mail: Ziyatdinovag@mail.ru [Analytical Chemistry Department, A.M. Butlerov Institute of Chemistry, Kazan (Volga Region) Federal University, Kremlyevskaya, 18, Kazan 420008 (Russian Federation); Ziganshina, Endzhe; Budnikov, Herman [Analytical Chemistry Department, A.M. Butlerov Institute of Chemistry, Kazan (Volga Region) Federal University, Kremlyevskaya, 18, Kazan 420008 (Russian Federation)

    2012-09-26

    Highlights: Black-Right-Pointing-Pointer Applicability of surfactants in constant-current coulometry is shown for the first time. Black-Right-Pointing-Pointer Reactions of antioxidants with electrogenerated titrants in surfactant media are investigated. Black-Right-Pointing-Pointer Water insoluble antioxidants can be determined in water media with addition of surfactants. Black-Right-Pointing-Pointer Coulometric determination of antioxidants in pharmaceutical dosage forms using surfactants media is developed. - Abstract: Effect of surfactant presence on electrochemical generation of titrants has been evaluated and discussed for the first time. Cationic (1-dodecylpyridinium and cetylpyridinium bromide), anionic (sodium dodecyl sulfate) and nonionic (Triton X100 and Brij{sup Registered-Sign} 35) surfactants as well as nonionic high molecular weight polymer (PEG 4000) do not react with the electrogenerated bromine, iodine and hexacyanoferrate(III) ions. The electrogenerated chlorine chemically interact with Triton X100 and Brij{sup Registered-Sign} 35. The allowable range of surfactants concentrations providing 100% current yield has been found. Chain-breaking low molecular weight antioxidants (ascorbic acid, rutin, {alpha}-tocopherol and retinol) were determined by reaction with the electrogenerated titrants in surfactant media. Nonionic and cationic surfactants can be used for the determination of antioxidants by reaction with the electrogenerated halogens. On contrary, cationic surfactants gives significantly overstated results of antioxidants determination with electrogenerated hexacyanoferrate(III) ions. The use of surfactants in coulometry of {alpha}-tocopherol and retinol provides their solubilization and allows to perform titration in water media. Simple, express and reliable coulometric approach for determination of {alpha}-tocopherol, rutin and ascorbic acid in pharmaceuticals using surfactant media has been developed. The relative standard deviation of the

  7. The effect of surfactants on the electropolishing behavior of copper in orthophosphoric acid

    Energy Technology Data Exchange (ETDEWEB)

    Taha, A.A., E-mail: asia_taha@yahoo.com; Ahmed, A.M.; Rahman, H.H. Abdel; Abouzeid, F.M.

    2013-07-15

    The electropolishing behavior of copper was studied in orthophosphoric acid with Triton X-100, sodium dodecyl sulphate and cetyl pyridinium chloride as additives for improving the finish obtained on copper surface. This was investigated by measuring and comparing anode potential-limiting current relationships in solutions of gradually increasing concentration of surfactants. The addition of surfactants to the electropolishing solution results in a lower limiting current. This confirms the mass transport of dissolved species from the anode surface to the bulk of solution as the rate-determining step in the presence of three surfactants in all concentrations investigated. Scanning electron microscope (SEM), atomic force microscope (AFM) and measured brightness values were used to investigate the copper surface after electropolishing and the results were compared to polishing done in absence of surfactants. According to SEM images and brightness values, addition of Triton X-100 was effective to enhance levelling and brightening more than sodium dodecyl sulphate and cetyl pyridinium chloride. AFM analysis showed that the roughness values (R{sub a}) for an electropolished copper surface, in presence of surfactants, is significantly lower than in absence of surfactants. Different reaction conditions and the physical properties of solutions are studied to obtain dimensionless correlation among all these parameters.

  8. Cytotoxic effect of organic solvents and surfactant agents on Acanthamoeba castellanii cysts.

    Science.gov (United States)

    Ezz Eldin, Hayam Mohamed; Sarhan, Rania Mohamed

    2014-05-01

    Acanthamoeba castellanii is a protozoan parasite that may cause sight-threatening keratitis in some individuals. Its eradication is difficult because the trophozoites encyst making organisms highly resistant to anti-amoebic drugs. To test new anti-Acanthamoeba agents, usually having low water solubility, organic solvents and surfactant agents should be used. Therefore, the lethal effect of different concentrations of the solvents acetone, methanol, ethanol, and DMSO and surfactant agents Tween 20, Tween 80, and Triton X-100 was tested. The minimal inhibitory concentrations (MIC) were determined against Acanthamoeba cysts. Results of the present study showed that the MIC for ethanol, methanol, acetone and DMSO was 25, 12.5, 12.5, and 10%, respectively and for Tween 20, Tween 80, and Triton X-100 was 0.25, 0.06, and 0.03%, respectively. There was no significant inhibitory effect on the multiplication of Acanthamoeba cysts as compared to parasite control when using the concentrations 3.12% for ethanol, 1.6% for methanol and acetone, 1.25% for DMSO, and 0.016% for Tween 20. On the other hand, both Tween 80 and Triton X-100 showed highly significant difference in comparison to parasite control almost among all the range of concentrations used in this study, and both showed lethal effect of 19 and 27.2%, respectively at their least concentration.

  9. Modification of shape oscillations of an attached bubble by surfactants

    Directory of Open Access Journals (Sweden)

    Tihon J.

    2013-04-01

    Full Text Available Surface-active agents (surfactants, e.g. washing agents strongly modifies properties of gas-liquid interface. We have carried out extensive experiments, in which we study effect of surfactants on the shape oscillations of a bubble, which is attached at a tip of a capillary. In the experiments, shape oscillations of a bubble are invoked by a motion of a capillary, to which the bubble is injected. Decaying oscillations are recorded and their frequency and damping are evaluated. By changing the excitation frequency, three lowest oscillation modes are studied. Experiments were repeated in aqueous solution of several surfactants (terpineol, SDS, CTAB, Triton X-100, Triton X-45 at various concentrations. Generally, these features are observed: Initially a surfactant addition leads to an increase of the oscillation frequency (though surface tension is decreasing; this effect can be attributed to the increasing interfacial elasticity. The decay time of oscillation is strongly decreasing, as a consequence of energy dissipation linked with Marangoni stresses. At a certain critical concentration, frequency decreases abruptly and the decay time passes by a minimum. With further addition of surfactant, frequency decreases, and the decay time slightly lengthens. Above critical micelle concentration, all these parameters stabilize. Interestingly, the critical concentration, at which frequency drop occurs, depends on mode order. This clearly shows that the frequency drop and minimum decay time are not a consequence of some abrupt change of interfacial properties, but are a consequence of some phenomena, which still need to be explained.

  10. Modification of shape oscillations of an attached bubble by surfactants

    Science.gov (United States)

    Vobecká, L.; Vejražka, J.; Tihon, J.

    2013-04-01

    Surface-active agents (surfactants, e.g. washing agents) strongly modifies properties of gas-liquid interface. We have carried out extensive experiments, in which we study effect of surfactants on the shape oscillations of a bubble, which is attached at a tip of a capillary. In the experiments, shape oscillations of a bubble are invoked by a motion of a capillary, to which the bubble is injected. Decaying oscillations are recorded and their frequency and damping are evaluated. By changing the excitation frequency, three lowest oscillation modes are studied. Experiments were repeated in aqueous solution of several surfactants (terpineol, SDS, CTAB, Triton X-100, Triton X-45) at various concentrations. Generally, these features are observed: Initially a surfactant addition leads to an increase of the oscillation frequency (though surface tension is decreasing); this effect can be attributed to the increasing interfacial elasticity. The decay time of oscillation is strongly decreasing, as a consequence of energy dissipation linked with Marangoni stresses. At a certain critical concentration, frequency decreases abruptly and the decay time passes by a minimum. With further addition of surfactant, frequency decreases, and the decay time slightly lengthens. Above critical micelle concentration, all these parameters stabilize. Interestingly, the critical concentration, at which frequency drop occurs, depends on mode order. This clearly shows that the frequency drop and minimum decay time are not a consequence of some abrupt change of interfacial properties, but are a consequence of some phenomena, which still need to be explained.

  11. Effects of various surfactants on the dispersion stability and electrical conductivity of surface modified graphene

    Energy Technology Data Exchange (ETDEWEB)

    Uddin, Md. Elias [WCU Program, Department of BIN Fusion Technology, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Kuila, Tapas [Surface Engineering and Tribology, CSIR – Central Mechanical Engineering Research Institute, Durgapur 721 302 (India); Nayak, Ganesh Chandra [Department of Applied Chemistry, ISM Dhanbad, Dhanbad 826 004, Jharkhand (India); Kim, Nam Hoon [Department of Hydrogen and Fuel Cell Engineering, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Ku, Bon-Cheol [Institute of Advanced Composite Materials, Korea Institute of Science and Technology, Dunsan-ri, Bongdong-eup, Wanju-gun, Jeollabuk-do 864-9 (Korea, Republic of); Lee, Joong Hee, E-mail: jhl@chonbuk.ac.kr [WCU Program, Department of BIN Fusion Technology, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of); Department of Hydrogen and Fuel Cell Engineering, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of)

    2013-06-15

    Highlights: ► Water dispersible graphene has been prepared using ionic and non-ionic surfactants. ► XPS and FTIR spectra analysis confirm surface modification and reduction of GO. ► The highest water dispersibility is observed in the graphene modified with of SDBS. ► The best properties of modified graphene is achieved with GO/surfactant ratio of two. -- Abstract: Ionic and non-ionic surfactant functionalized, water dispersible graphene were prepared to investigate the effects on the dispersion stability and electrical conductivity of graphene. In this study, sodium dodecyl benzene sulfonate (SDBS), sodium dodecyl sulfate and 4-(1,1,3,3-tetramethylbutyl) phenyl-polyethylene glycol (Triton X-100) were used as ionic and non-ionic surfactants. The effects of surfactant concentrations on the dispersibility and electrical conductivity of the surface modified graphene were investigated. The dispersion stability of SDBS functionalized graphene (SDBS-G) was found to be best in water at 1.5 mg ml{sup −1}. X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy analysis indicate that the presence of surfactants does not prevent the reduction of graphene oxide (GO). These measurements also demonstrated that the surfactants were present on the surface of graphene, resulting in the formation of functionalized graphene. The thickness of different functionalized graphene was measured by Atomic force microscopy and varied significantly with different surfactants. The thermal properties of the functionalized graphene were also found to be dependent on the nature of the surfactants. The electrical conductivity of SDBS-G (108 S m{sup −1}) was comparatively higher than SDS and Triton X-100 functionalized graphene.

  12. Effects of various surfactants on the dispersion stability and electrical conductivity of surface modified graphene

    International Nuclear Information System (INIS)

    Uddin, Md. Elias; Kuila, Tapas; Nayak, Ganesh Chandra; Kim, Nam Hoon; Ku, Bon-Cheol; Lee, Joong Hee

    2013-01-01

    Highlights: ► Water dispersible graphene has been prepared using ionic and non-ionic surfactants. ► XPS and FTIR spectra analysis confirm surface modification and reduction of GO. ► The highest water dispersibility is observed in the graphene modified with of SDBS. ► The best properties of modified graphene is achieved with GO/surfactant ratio of two. -- Abstract: Ionic and non-ionic surfactant functionalized, water dispersible graphene were prepared to investigate the effects on the dispersion stability and electrical conductivity of graphene. In this study, sodium dodecyl benzene sulfonate (SDBS), sodium dodecyl sulfate and 4-(1,1,3,3-tetramethylbutyl) phenyl-polyethylene glycol (Triton X-100) were used as ionic and non-ionic surfactants. The effects of surfactant concentrations on the dispersibility and electrical conductivity of the surface modified graphene were investigated. The dispersion stability of SDBS functionalized graphene (SDBS-G) was found to be best in water at 1.5 mg ml −1 . X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy analysis indicate that the presence of surfactants does not prevent the reduction of graphene oxide (GO). These measurements also demonstrated that the surfactants were present on the surface of graphene, resulting in the formation of functionalized graphene. The thickness of different functionalized graphene was measured by Atomic force microscopy and varied significantly with different surfactants. The thermal properties of the functionalized graphene were also found to be dependent on the nature of the surfactants. The electrical conductivity of SDBS-G (108 S m −1 ) was comparatively higher than SDS and Triton X-100 functionalized graphene

  13. NMR study of the dynamics of cationic gemini surfactant 14-2-14 in mixed solutions with conventional surfactants.

    Science.gov (United States)

    Jiang, Yan; Lu, Xing-Yu; Chen, Hong; Mao, Shi-Zhen; Liu, Mai-Li; Luo, Ping-Ya; Du, You-Ru

    2009-06-18

    Three kinds of conventional surfactants, namely, two nonionic surfactants [polyethylene glycol (23) lauryl ether (Brij-35) and Triton X-100 (TX-100)], one cationic surfactant [n-tetradecyltrimethyl ammonium bromide (TTAB)], and an anionic surfactant [sodium n-dodecyl sulfate (SDS)}, were mixed into the quaternary ammonium gemini surfactant [C(14)H(29)N(+)(CH(3))(2)](2)(CH(2))(2).2Br(-) (14-2-14) in aqueous solution. The exchange rate constants between 14-2-14 molecules in the mixed micelles and those in the bulk solution were detected using two nuclear magnetic resonance (NMR) methods: one-dimensional (1D) line shape analysis and two-dimensional (2D) exchange spectroscopy (EXSY). The results obtained from these two methods were consistent. Both showed that mixing a nonionic conventional surfactant, either Brij-35 or TX-100, enhanced the exchange process between the 14-2-14 molecules in the mixed micelles and those in the bulk solution. In contrast, the anionic surfactant SDS and the cationic surfactant TTAB slowed the process slightly.

  14. Optimizing the surfactant for the aqueous processing of LiFePO{sub 4} composite electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Porcher, W.; Jouanneau, S. [Commissariat a l' Energie Atomique, 38054 Grenoble Cedex 9 (France); Lestriez, B.; Guyomard, D. [Institut des Materiaux Jean Rouxel (IMN), Universite de Nantes, CNRS, 44322 Nantes Cedex 3 (France)

    2010-05-01

    Aqueous processing would reduce the costs associated with the making of the composite electrode. To achieve the incorporation and the dispersion of the carbon black (CB) conductive agent in aqueous slurries, a surfactant is needed. In this paper, three surfactants are compared, an anionic one, the sodium dodecyle sulphate (SDS), a non-ionic one, the isooctylphenylether of polyoxyethylene called commercially Triton X-100 and a cationic one, the hexadecyltrimethylammonium bromide (CTAB), by using rheology and laser granulometry measurements on electrode slurries on one hand, and SEM observations, porosity and adhesion measurements and electrochemical testing on composite electrodes on the other hand. Ionic surfactants were found to be not suitable because a corrosion of the aluminium current collector occurred. The utilization of Triton X-100 favoured a more homogeneous CB distribution, resulted in a better electronic wiring of the active material particles and higher rate behavior of the electrode. Optimal electrochemical performances are obtained for an optimal surfactant concentration which depends on the BET surface area of the CB powder. (author)

  15. Effects of surfactants on graphene oxide nanoparticles transport in saturated porous media.

    Science.gov (United States)

    Fan, Wei; Jiang, Xuehui; Lu, Ying; Huo, Mingxin; Lin, Shanshan; Geng, Zhi

    2015-09-01

    Transport behaviors of graphene oxide nanoparticles (GONPs) in saturated porous media were examined as a function of the presence and concentration of anionic surfactant (SDBS) and non-ionic surfactant (Triton X-100) under different ionic strength (IS). The results showed that the GONPs were retained obviously in the sand columns at both IS of 50 and 200mmol/L, and they were more mobile at lower IS. The presence and concentration of surfactants could enhance the GONP transport, particularly as observed at higher IS. It was interesting to see that the GONP transport was surfactant type dependent, and SDBS was more effective to facilitate GONP transport than Triton X-100 in our experimental conditions. The advection-dispersion-retention numerical modeling followed this trend and depicted the difference quantitatively. Derjaguin-Landau-Verwey-Overbeek (DLVO) interaction calculations also were performed to interpret these effects, indicating that secondary minimum deposition was critical in this study. Copyright © 2015. Published by Elsevier B.V.

  16. The effect of surfactants on electrohydrodynamic jet printing and the performance of organic field-effect transistors.

    Science.gov (United States)

    Li, Xinlin; Jeong, Yong Jin; Jang, Jaeyoung; Lim, Sooman; Kim, Se Hyun

    2018-01-03

    In this article, we report on the direct writing of multi-walled carbon nanotube (MWCNT) composite inks based on three different surfactants via the electrohydrodynamic (EHD) jet printing technique. All three surfactants, including two types of polymeric surfactants and an ionic surfactant, successfully dispersed the MWCNTs in the ink medium. Although the MWCNT composite with the ionic surfactant could not be printed by the EHD process, the MWCNT composites with polymeric surfactants could be successfully printed using this technique. Furthermore, the printed lines exhibited different electrical and electronic characteristics, depending on the type of surfactant. A large amount of the poly(4-styrenesulfonic acid) (PSS) surfactant was required to disperse the MWCNTs in ethanol, whereas a smaller amount of polymeric Triton X-100 (TX100) was required to obtain a MWCNT composite suspension in distilled water, and therefore, the printed lines of the latter provided higher conductivities. In addition, the surface potential and charge carrier injection properties of the EHD-printed MWCNT lines depended on the type of surfactant in the MWCNT composite. Finally, organic field-effect transistors (OFETs) employing source/drain electrodes based on MWCNT/surfactant composites exhibited opposing electrical characteristics depending on the type of surfactant. The MWCNT/PSS lines showed excellent electrical performance when used as electrodes in p-type OFETs, whereas the MWCNT/TX100 lines exhibited excellent performance when used as electrodes in n-type OFETs.

  17. Investigation on Minimum Film Boiling Point of Highly Heated Vertical Metal Rod in Aqueous Surfactant Solution

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chi Young; Kim, Jae Han [Pukyong Nat’l Univ., Busan (Korea, Republic of)

    2017-09-15

    In this study, experiments were conducted on the MFB(minimum film boiling) point of highly heated vertical metal rod quenched in aqueous surfactant solution at various temperature conditions. The aqueous Triton X-100 solution(100 wppm) and pure water were used as the liquid pool. Their temperatures ranged from 77 °C to 100 °C. A stainless steel vertical rod of initial center temperature of 500 °C was used as a test specimen. In both liquid pools, as the liquid temperature decreased, the time to reach the MFB point decreased with a parallel increase in the temperature and heat flux of the MFB point. However, over the whole present temperature range, in the aqueous Triton X-100 solution, the time to reach the MFB point was longer, while the temperature and heat flux of the MFB point were reduced when compared with pure water. Based on the present experimental data, this study proposed the empirical correlations to predict the MFB temperature of a high temperature vertical metal rod in pure water and in aqueous Triton X-100 solution.

  18. Antigenic properties of the envelope of influenza virus rendered soluble by surfactant-solvent systems

    Science.gov (United States)

    Larin, N. M.; Gallimore, P. H.

    1971-01-01

    Dissociating chemical treatments employing surfactant-solvent systems were applied to purified influenza A and B viruses to obtain viral preparations possessing a significantly higher or lower haemagglutinating activity than the intact virus. All preparations, whether with high or low haemagglutinating activity, with the exception of envelope protein solubilized by Triton X-100, were significantly lacking in the ability to excite the formation of haemagglutination-inhibiting and virus-neutralizing antibodies in inoculated ferrets. In contrast to other treatments, Triton X-100 treatment of virus significantly enhanced the antigenicity of viral protein as judged by virus neutralization and haemagglutination inhibition tests. Yet the haemagglutinating activity of the envelope protein solubilized with Triton X-100 was about 1% that of the intact virus. Results suggest that the correlation assumed to exist between the haemagglutinating activity of influenza virus and its ability to excite the formation of humoral antibodies is coincidental. Another important point is that the specific antigenicity of viral protein may be lost or enhanced owing to effects, other than solubilization, by surface-active agents. PMID:5291750

  19. Pyrene removal from contaminated soil using electrokinetic process combined with surfactant

    Directory of Open Access Journals (Sweden)

    Seyed Enayat Hashemi

    2015-07-01

    Full Text Available Background: Pyrene is one of the stable polycyclic aromatic hydrocarbons that is considered as an important pollutants, because of extensive distribution in the environment and carcinogenic and mutagenic properties. Among the various treatment techniques, electrokinetic method is an environmental- friendly process for organic and mineral pollutants adsorbed to soil with fine pore size the same as clay and low hydraulic conductivity soils. For improving the efficiency of pyrene removal from soil, soulobilization of pyrene from soil could be used by surfactants. Materials and Methods : In this study, clay soil was selected as model because of the specific properties. Combined method using surfactant and electrokinetic was applied for pyrene removal from soil. Experiments were designed using response surface methodology (RSM, and effect of three variables includes surfactant concentration, voltage and surfactant type were evaluated for pyrene removal from contaminated soil. Results: Pyrene removal using anionic surfactants(SDS and nonionic surfactants(TX100 as a solubilizing agents has high removal efficiency. In the optimum condition with 95% confidence coefficient, utilizing mixed surfactants of sodium dodecyl sulfate and triton X-100 with the same volume, induced of 18.54 volt and 6.53 percent surfactant concentration have 94.6% pyrene removal efficiency. Conclusion:: Results of this study shows that electrokinetic process combined with surfactant as solubilizing agent could be applied as an efficient method for treating the pyrene-contaminated soils.

  20. A conductometric investigation of hydroxypropylmethyl cellulose/sodium dodecyl sulfate/nonionic surfactant systems

    Directory of Open Access Journals (Sweden)

    Petrović Lidija B.

    2014-01-01

    Full Text Available Surfactant mixtures are very often used in various cosmetic and pharmaceutical products because they commonly act in synergism and provide more favorable properties than the single surfactants. At the same time, the 9 presence of polymers in mixtures of surfactants may lead to molecular interactions thereby affecting product stability and activity. For these reasons it is very important to determine the surfactant interactions influence on 1micellization and mixed micellization, as well as polymer-surfactants mixed micelles interactions. In this work we examined self-aggregation of nonionic surfactants, polysorbate 20 (Tween 20, polyoxyethylene octylphenyl ether (Triton X100 and polyoxyethylene-polyoxypropylene block copolymer (Pluronic F68 with ionic surfactant, sodium dodecylsulfate, in aqueous solution at 40ºC using conductometric titration method. It was found that concentration region for mixed micelle formation depends on nonionic surfactant characteristics and its concentration. Formation of surfactants mixed micelles in the presence of nonionic polymer, hydroxypropylmethyl cellulose, and their binding to polymer hydrophobic sites, were investigated too. Analysis of obtained results points to different kinds of interactions in investigated systems, which are crucial for their application. [Projekat Ministarstva nauke Republike Srbije, br. III 46010

  1. Spectrophotometric determination of molybdenum with non-ionic surfactant and thiocyanate

    International Nuclear Information System (INIS)

    Hayashi, Kenjiro; Yamamoto, Atsuo; Fujimura, Yasue; Ito, Saburo.

    1980-01-01

    Although the molybdenum (V)-thiocyanate complex is quite stable in non-aqueous solvent such as ether, the complex in dilute acidic solution is unstable. However, this unstable complex was stabilized remarkably by addition of some non-ionic surfactant such as Triton X-100 (alkylphenolpolyoxyethylene ether). The application of this stabilizing effect of the surfactant to the photometric determination of trace amounts of molybdenum with thiocyanate resulted in an increase in the sensitivity. The rate of formation of the Mo(V)-SCN complex was affected by the presence of ferrous ion and its rate constant was proportional to the concentration of Fe(II). The stabilizing effect of the surfactant on the yellowish orange coloration can be understood if we assume that the Mo(V)-SCN complex is incorporated into the micelles of Triton X-100 as [H 2 + , MoO(CNS) 5 2- ]. The optimum condition for the determination of molybdenum is as follows: concentration of sulfuric acid, 0.22 mol dm -3 ; Triton X-100, 0.8%; ascorbic acid, 0.32 mol dm -3 ; thiocyanate, 0.30 mol dm -3 ; iron, 40 mg dm -3 ; standing time for coloration, 10 min and more. Beer's law was obeyed over the range (1 -- 233) μg/50 cm 3 . The molar absorption coefficient at 468 nm was 1.7 2 x 10 4 cm -1 mol -1 dm 3 . The maximum permissible limits of foreign ions (mg/50 cm 3 ) were as follows: Ni(30); Co(12); W(VI) (2); Cu, Zn, V(V) (3); Cr(VI) (5). Large amounts of iron interfered, but this interference was removed by addition of the same amount of iron to the reagent blank. Trace amounts of molybdenum in steel was determined by this method with satisfactory results. (author)

  2. Preparation of Melamine - Formaldehyde Microcapsules Containing Hexadecane as a Phase Change Material: The Effect of Surfactants Type and Concentration

    Directory of Open Access Journals (Sweden)

    Zeinab Alinejad

    2013-05-01

    Full Text Available Microcapsules containing n-hexadecane (HD as the core and melamineformaldehyde (MF prepolymer as the shell were prepared by in-situ dispersion polymerization. The effects of surfactants type and amount were studied in relation to the morphology and thermal properties of microcapsules. The morphology of the microcapsules was studied using scanning electron microscopy (SEM and thermal properties were detected by differential scanning calorimetry (DSC and thermogravimetric analysis (TGA. SEM images showed that the increase in the amount of Triton X-100 (non-ionic to SDS (ionic ratio resulted in the agglomeration of the prepared microcapsules. This increase led also to lower encapsulated hexadecane and thermal stability of microcapsules. As a result, the optimum composition of the above surfactants for obtaining higher thermal stability and proper morphology wasfound to be 20 wt% of Triton X-100 and 80 wt% of SDS in the recipe. The optimum total amounts of surfactants was 4 wt%, which resulted in spherical and separate microcapsules. DSC and TGA analyses revealed that a sample prepared with 4 wt% of surfactants was not only successful in encapsulation of hexadecane but also showedhigher thermal stability compared with other formulations.

  3. Tuning intermicellar potential of Triton X-100– anthranilic acid mixed ...

    Indian Academy of Sciences (India)

    solubilized anthranilic acid at different pH values was investigated using light scattering and small angle neutron scattering. Analysis of the SANS data indicate that micelles are oblate ellipsoidal in nature with little variation in the dimensions, in the investigated pH range (from 0.5 to 6.0). The interaction potential of the ...

  4. The Utilization of Triton X-100 for Enhanced Two-Dimensional Liquid-Phase Proteomics

    OpenAIRE

    Kim, Mina; Lee, Sang-Hee; Min, Jiho; Kobayashi, Fumihisa; Um, Hyun-Ju; Kim, Yang-Hoon

    2011-01-01

    One of the main challenges in proteomics lies in obtaining a high level of reproducible fractionation of the protein samples. Automated two-dimensional liquid phase fractionation (PF2D) system manufactured by Beckman Coulter provides a process well suited for proteome studies. However, the protein recovery efficiency of such system is low when a protocol recommended by the manufacturer is used for metaproteome profiling of environmental sample. In search of an alternative method that can over...

  5. Tuning intermicellar potential of Triton X-100–anthranilic acid mixed ...

    Indian Academy of Sciences (India)

    A similar variation is observed in the cloud point of the micelles with pH. The observed variation in the interaction potential with pH of the micellar solution can be explained in terms of the reversal of charge on anthranilic acid due to shift in the acid–base equilibrium. The variation in interaction potential and cloud point with ...

  6. Different behaviour of GPCRs from rat brain cortex when exposed to Triton X-100

    Czech Academy of Sciences Publication Activity Database

    Rudajev, Vladimír; Stöhr, Jiří; Bouřová, Lenka; Lisý, Václav; Novotný, Jiří; Svoboda, Petr

    2007-01-01

    Roč. 101, Suppl.1 (2007), s. 52-52 ISSN 0022-3042. [European Society for Neurochemistry Meeting /17./. 19.05.2007-22.05.2007, Salamanca] Institutional research plan: CEZ:AV0Z50110509 Keywords : cpo1 * detergent resistant membrane domains * GABAB receptor * Beta-adrenergic receptor Subject RIV: ED - Physiology

  7. Surfactant mediated extraction of total phenolic contents (TPC) and antioxidants from fruits juices.

    Science.gov (United States)

    Sharma, Shweta; Kori, Shivpoojan; Parmar, Ankush

    2015-10-15

    The aim of this study was to enhance the extraction of total phenolic contents (TPC) and antioxidants from fruit juices by the application of surfactants formulations instead of conventional solvents (methanol, ethanol and acetone). A variety of fruit infusions: apple red delicious (apple (rd)) (Malus domestica), Mcintosh apple (apple (i)) (Malus pumila), sweet lemon (Citrus limetta) and mango (Magnifera indica) were studied. Effect of water, organic solvents and five different aqueous surfactant formulations viz. SDS, Brij-35, Brij-58, Triton X-100 and Span-40 were explored for the extraction of TPC and determining the antioxidant activity (AA). The TPC and AA (%) were determined using Folin-Ciocalteu (FCA) and DPPH assay, respectively. The effect of surfactant type, concentration and common organic solvents on the extraction of TPC and AA (%) was studied using UV-visible spectrophotometric technique. Among all the extracting systems employed, Brij-58 showed the highest extraction efficiency. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. In vitro surfactant structure-toxicity relationships: implications for surfactant use in sexually transmitted infection prophylaxis and contraception.

    Directory of Open Access Journals (Sweden)

    Ângela S Inácio

    Full Text Available BACKGROUND: The need for woman-controlled, cheap, safe, effective, easy-to-use and easy-to-store topical applications for prophylaxis against sexually transmitted infections (STIs makes surfactant-containing formulations an interesting option that requires a more fundamental knowledge concerning surfactant toxicology and structure-activity relationships. METHODOLOGY/PRINCIPAL FINDINGS: We report in vitro effects of surfactant concentration, exposure time and structure on the viability of mammalian cell types typically encountered in the vagina, namely, fully polarized and confluent epithelial cells, confluent but non-polarized epithelial-like cells, dendritic cells, and human sperm. Representatives of the different families of commercially available surfactants--nonionic (Triton X-100 and monolaurin, zwitterionic (DDPS, anionic (SDS, and cationic (C(nTAB (n = 10 to 16, C(12PB, and C(12BZK--were examined. Triton X-100, monolaurin, DDPS and SDS were toxic to all cell types at concentrations around their critical micelle concentration (CMC suggesting a non-selective mode of action involving cell membrane destabilization and/or destruction. All cationic surfactants were toxic at concentrations far below their CMC and showed significant differences in their toxicity toward polarized as compared with non-polarized cells. Their toxicity was also dependent on the chemical nature of the polar head group. Our results suggest an intracellular locus of action for cationic surfactants and show that their structure-activity relationships could be profitably exploited for STI prophylaxis in vaginal gel formulations. The therapeutic indices comparing polarized epithelial cell toxicity to sperm toxicity for all surfactants examined, except C(12PB and C(12BZK, does not justify their use as contraceptive agents. C(12PB and C(12BZK are shown to have a narrow therapeutic index recommending caution in their use in contraceptive formulations. CONCLUSIONS

  9. In vitro surfactant structure-toxicity relationships: implications for surfactant use in sexually transmitted infection prophylaxis and contraception.

    Science.gov (United States)

    Inácio, Ângela S; Mesquita, Katia A; Baptista, Marta; Ramalho-Santos, João; Vaz, Winchil L C; Vieira, Otília V

    2011-01-01

    The need for woman-controlled, cheap, safe, effective, easy-to-use and easy-to-store topical applications for prophylaxis against sexually transmitted infections (STIs) makes surfactant-containing formulations an interesting option that requires a more fundamental knowledge concerning surfactant toxicology and structure-activity relationships. We report in vitro effects of surfactant concentration, exposure time and structure on the viability of mammalian cell types typically encountered in the vagina, namely, fully polarized and confluent epithelial cells, confluent but non-polarized epithelial-like cells, dendritic cells, and human sperm. Representatives of the different families of commercially available surfactants--nonionic (Triton X-100 and monolaurin), zwitterionic (DDPS), anionic (SDS), and cationic (C(n)TAB (n = 10 to 16), C(12)PB, and C(12)BZK)--were examined. Triton X-100, monolaurin, DDPS and SDS were toxic to all cell types at concentrations around their critical micelle concentration (CMC) suggesting a non-selective mode of action involving cell membrane destabilization and/or destruction. All cationic surfactants were toxic at concentrations far below their CMC and showed significant differences in their toxicity toward polarized as compared with non-polarized cells. Their toxicity was also dependent on the chemical nature of the polar head group. Our results suggest an intracellular locus of action for cationic surfactants and show that their structure-activity relationships could be profitably exploited for STI prophylaxis in vaginal gel formulations. The therapeutic indices comparing polarized epithelial cell toxicity to sperm toxicity for all surfactants examined, except C(12)PB and C(12)BZK, does not justify their use as contraceptive agents. C(12)PB and C(12)BZK are shown to have a narrow therapeutic index recommending caution in their use in contraceptive formulations. Our results contribute to understanding the mechanisms involved in

  10. Removal of 226Ra and 228Ra from TENORM sludge waste using surfactants solutions.

    Science.gov (United States)

    Attallah, M F; Hamed, Mostafa M; El Afifi, E M; Aly, H F

    2015-01-01

    The feasibility of using surfactants as extracting agent for the removal of radium species from TENORM sludge produced from petroleum industry is evaluated. In this investigation cationic and nonionic surfactants were used as extracting agents for the removal of radium radionuclides from the sludge waste. Two surfactants namely cetyltrimethylammonium bromide (CTAB) and Triton X-100 (TX100) were investigated as the extracting agents. Different parameters affecting the removal of both (226)Ra and (228)Ra by the two surfactants as well as their admixture were studied by the batch technique. These parameters include effect of shaking time, surfactants concentration and temperature as well as the effect of surfactants admixture. It was found that, higher solution temperature improves the removal efficiency of radium species. Combined extraction of nonionic and cationic surfactants produces synergistic effect in removal both (226)Ra and (228)Ra, where the removals reached 84% and 80% for (226)Ra and (228)Ra, respectively, were obtained using surfactants admixture. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. On the formation of new reverse micelles: a comparative study of benzene/surfactants/ionic liquids systems using UV-visible absorption spectroscopy and dynamic light scattering.

    Science.gov (United States)

    Falcone, R Darío; Correa, N Mariano; Silber, Juana J

    2009-09-15

    The microenvironment of the polar core generated in different ionic liquid reverse micelle (IL RM) systems were investigated using the solvatochromic behavior of 1-methyl-8-oxyquinolinium betaine (QB) as an absorption probe and dynamic light scattering (DLS) technique. The novel RM systems consist of two different ILs--1-butyl-3-methylimidazolium tetrafluoroborate (bmimBF4) and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (bmimTf2N)--sequestrated by two different surfactants--Triton X-100 (TX-100) and benzyl-n-hexadecyldimethylammonium chloride (BHDC)--in order to make IL/surfactant/benzene RMs. The effect of the variation of Ws (Ws=[IL]/[surfactant]) on the QB spectroscopy was used to characterize these nonaqueous RMs. DLS results confirm the formation of these IL RM systems because increasing Ws increases the droplet sizes. Moreover it is demonstrated that the structure of the sequestrated ILs depends strongly on the type of surfactant use to create the RMs.

  12. Effect of various surfactants (cationic, anionic and non-ionic) on the growth of Aspergillus parasiticus (NRRL 2999) in relation to aflatoxin production.

    Science.gov (United States)

    Tanuja, Kosuri; Hemalatha, K; Karuna, Rupula; Sashidhar Rao, B

    2010-08-01

    The effect of surfactants (two cationic, one anionic and three non-ionic) at 0.001, 0.01, 0.1 and 1.0 % concentrations on aflatoxin production, ergosterol content and sugar consumption by Aspergillus parasiticus (NRRL 2999) in YES liquid culture medium is reported. At 0.01% concentration, the cationic surfactants, cetyl dimethyl ammonium bromide (CDAB) and dodecyl trimethyl ammonium bromide (DTAB), and the anionic surfactant, sodium dodecyl sulfate (SDS), completely inhibited spore germination, while DTAB also inhibited the production of ergosterol and toxin (p lauryl ether (Brij-35) and ethoxylated p-tert-octylphenol (Triton X-100) delayed the spore germination up to day 5 at all concentrations and inhibited toxin and ergosterol production at 0.001% concentration. The affect was found to be dose-dependent from 0.001% to 1%, for Triton X-100 only. Positive correlation between ergosterol content and toxin production in the presence of different surfactants at various time periods (3, 5, 7, 9 and 12 days) was found. Tween-20 was most effective in inhibiting toxin production on day 7, when aflatoxin production was found to be maximal in control group. Sugar consumption was directly proportional to the ergosterol content, showing a significant correlation with aflatoxin production.

  13. Influence of nonionic surfactants on the potentiometric response of hydrogen ion-selective polymeric membrane electrodes.

    Science.gov (United States)

    Espadas-Torre, C; Bakker, E; Barker, S; Meyerhoff, M E

    1996-05-01

    The influence of poly(ethylene oxide)-based nonionic surfactants (i.e., Triton X-100 and Brij 35) in the sample phase on the response properties of hydrogen ion-selective polymeric membrane electrodes containing mobile (lipophilic amines) or covalently bound (aminated-poly-(vinyl chloride)) hydrogen ion carriers is reported. In the presence of these nonionic surfactants, membrane electrode response toward interfering cation activity (e.g., Na+) in the sample phase is increased substantially and the pH measuring range shortened. The degree of cation interference for pH measurements is shown to correlate with the basicity of the hydrogen ion carrier doped within the membrane phase. The observed deterioration in selectivity arises from the partitioning of the surfactant into the membrane and concomitant extraction of metal cations by the surfactants in the organic phase. The effect of nonionic surfactants on pH electrodes prepared with aminated-PVC membranes is shown to be more complex, with additional large shifts in EMF values apparently arising from multidentate interactions between the surfactant molecules and the polymeric amine in the membrane, leading to a change in the apparent pKa values for the amine sites. The effects induced by nonionic surfactants on the EMF response function of hydrogen ion-selective polymeric membrane electrodes are modeled, and experimental results are shown to correlate well with theoretical predictions.

  14. Effect of Four Commonly Used Dissolution Media Surfactants on Pancreatin Proteolytic Activity.

    Science.gov (United States)

    Guncheva, Maya; Stippler, Erika

    2017-05-01

    Proteolytic enzymes are often used in dissolution testing of cross-linked gelatin capsules that do not conform to the dissolution specification. Their catalytic activity, however, can be affected when they are added to a dissolution media containing solubility enhancers, such as surfactants. The aim of this study was to assess the activity of pancreatic proteases in presence of four commonly used surfactants. We found that pancreatin exhibits remarkable proteolytic activity in the presence of Tween 80, even at the concentrations as high as 250 times its critical micelle concentration (cmc) in water, whereas, Triton X-100 enhanced the proteolytic activity of pancreatin when added at concentrations above its cmc in water. Both surfactants are non-ionic surfactants. On the other hand, sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide (CTAB), which are ionic surfactants, have a detrimental effect on the proteolytic activity of pancreatin. For example, a 50% reduction of the pancreatin activity was found in samples which contain a minor amount of SDS (0.05% w/v) in comparison to a surfactant-free reaction. Additionally, no activity was observed for the pancreatin-SDS samples which were incubated for 30 min at 40°C prior to testing. CTAB had an impact on pancreatin activity at concentrations higher than its cmc. Data from this manuscript can be used as a benchmark for optimization of the dissolution procedures that require use of both surfactants and enzymes.

  15. Triton burnup in JET

    International Nuclear Information System (INIS)

    Chipsham, E.; Jarvis, O.N.; Sadler, G.

    1989-01-01

    Triton burnup measurements have been made at JET using time-integrated copper activation and time-resolved silicon detector techniques. The results confirm the classical nature of both the confinement and the slowing down of the 1 MeV tritons in a plasma. (author) 8 refs., 3 figs

  16. Global Warming on Triton

    Science.gov (United States)

    Elliot, J. L.; Hammel, H. B.; Wasserman, L. H.; Franz, O. G.; McDonald, S. W.; Person, M. J.; Olkin, C. B.; Dunham, E. J.; Spencer, J. R.; Stansberry, J. A.; hide

    1998-01-01

    Triton, Neptune's largest moon, has been predicted to undergo significant seasonal changes that would reveal themselves as changes in its mean frost temperature. But whether this temperature should at the present time be increasing, decreasing or constant depends on a number of parameters (such as the thermal properties of the surface, and frost migration patterns) that are unknown. Here we report observations of a recent stellar occultation by Triton which, when combined with earlier results, show that Triton has undergone a period of global warming since 1989. Our most conservative estimates of the rate of temperature and surface-pressure increase during this period imply that the atmosphere is doubling in bulk every 10 years, significantly faster than predicted by any published frost model for Triton. Our result suggests that permanent polar caps on Triton play a c dominant role in regulating seasonal atmospheric changes. Similar processes should also be active on Pluto.

  17. Synthesis of Mesoporous Nanocrystalline Zirconia by Surfactant-Assisted Hydrothermal Approach.

    Science.gov (United States)

    Nath, Soumav; Biswas, Ashik; Kour, Prachi P; Sarma, Loka S; Sur, Ujjal Kumar; Ankamwar, Balaprasad G

    2018-08-01

    In this paper, we have reported the chemical synthesis of thermally stable mesoporous nanocrystalline zirconia with high surface area using a surfactant-assisted hydrothermal approach. We have employed different type of surfactants such as CTAB, SDS and Triton X-100 in our synthesis. The synthesized nanocrystalline zirconia multistructures exhibit various morphologies such as rod, mortar-pestle with different particle sizes. We have characterized the zirconia multistructures by X-ray diffraction study, Field emission scanning electron microscopy, Attenuated total refection infrared spectroscopy, UV-Vis spectroscopy and photoluminescence spectroscopy. The thermal stability of as synthesized zirconia multistructures was studied by thermo gravimetric analysis, which shows the high thermal stability of nanocrystalline zirconia around 900 °C temperature.

  18. Surfactant-induced mobilisation of trace metals from estuarine sediment: Implications for contaminant bioaccessibility and remediation

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Anu [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Turner, Andrew [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)], E-mail: aturner@plymouth.ac.uk

    2009-02-15

    The mobilisation of metals (Al, Fe, Cd, Cu, Mn, Ni, Pb, Sn, Zn) from contaminated estuarine sediment has been examined using commercially available surfactants. Metal release by the anionic surfactant, sodium dodecyl sulphate (SDS), increased with increasing amphiphile concentration up to and above its critical micelle concentration (CMC). Metal mobilisation by the bile acid salt, sodium taurocholate, and the nonionic surfactant, Triton X-100, however, did not vary with amphiphile concentration. SDS was the most efficient surfactant in mobilising metals from the sample, and Cd, Cu and Ni were released to the greatest extents (12-18% of total metal at [SDS] > CMC). Metal mobilisation appeared to proceed via complexation with anionic amphiphiles and denudation of hydrophobic host phases. Surfactants may play an important role in the solubilisation of metals in the digestive environment of deposit-feeding animals and, potentially, in the remediation of metal-contaminated soil and sediment. - Significant quantities of metals are mobilised from estuarine sediment by commercially available surfactants.

  19. Sono-electroanalysis of copper: enhanced detection and determination in the presence of surfactants.

    Science.gov (United States)

    Hardcastle, Joanna Lorraine; Hignett, Geraldine; Melville, James L; Compton, Richard G

    2002-04-01

    Surfactant adsorption has been shown to have a passivating effect on the electrode surface during anodic stripping voltammetric measurements. In the present work the feasibility of sono-anodic stripping analysis for the determination of copper in aqueous media contaminated with surfactant has been studied at an unmodified bare glassy carbon electrode. We illustrate the deleterious effect of three common surfactants, sodium dodecyl sulfate (SDS), dodecyl pyridinium chloride (DPC) and Triton-X 100 (TX-100) on conventional electroanalysis. The analogous sono-electroanalytical response was investigated for each surfactant at ultrasound intensities above and below the cavitation threshold. The enhancement in the stripping signal observed is attributed to the increased mass transport due to acoustic streaming and above the cavitation threshold the intensity of cavitational events is significantly increased leading to shearing of adsorbed surfactant molecules from the surface. As a result accurate analyses for SDS concentrations up to 100 ppm are possible, with analytical signals visible in solutions of SDS and TX-100 of 1000 ppm. Analysis is reported in high concentration of surfactant with use of sono-solvent double extraction. The power of this technique is clearly illustrated by the ability to obtain accurate measurements of copper concentration from starting solutions containing 1000 ppm SDS or TX-100. This was also exemplified by analysis of the low concentration 0.3 microM Cu(II) solution giving a percentage recovery of 94% in the presence of 1000 ppm SDS or TX-100.

  20. Influence of MWCNT/surfactant dispersions on the mechanical properties of Portland cement pastes

    Science.gov (United States)

    Rodríguez, B.; Quintero, J. H.; Arias, Y. P.; Mendoza-Reales, O. A.; Ochoa-Botero, J. C.; Toledo-Filho, R. D.

    2017-12-01

    This work studies the reinforcing effect of Multi Walled Carbon Nanotubes (MWCNT) on cement pastes. A 0.35% solid concentration of MWCNT in powder was dispersed in deionized water with sodium dodecyl sulfate (cationic surfactant), cetylpyridinium chloride (anionic surfactant) and triton X-100 (amphoteric surfactant) using an ultrasonic tip processor. Three concentrations of each surfactant (1mM, 10mM and 100mM) were tested, and all samples were sonicated until an adequate dispersion degree was obtained. Cement pastes with additions of carbon nanotubes of 0.15% by mass of cement were produced in two steps; first the dispersions of MWCNT were combined with the mixing water using an ultrasonic tip processor to guarantee homogeneity, and then cement was added and mixed until a homogeneous paste was obtained. Direct tensile strength, apparent density and open porosity of the pastes were measured after 7 days of curing. It was found that the MWCNT/surfactants dispersions decrease the mechanical properties of the cement based matrix due to an increased porosity caused by the presence of surfactants.

  1. Effect of Surfactants on Mechanical, Thermal, and Photostability of a Monoclonal Antibody.

    Science.gov (United States)

    Agarkhed, Meera; O'Dell, Courtney; Hsieh, Ming-Ching; Zhang, Jingming; Goldstein, Joel; Srivastava, Arvind

    2018-01-01

    The purpose of this work was to evaluate the effect of commonly used surfactants (at 0.01% w/v concentration) on mechanical, thermal, and photostability of a monoclonal antibody (MAb1) of IgG1 sub-class and to evaluate the minimum concentration of surfactant (Polysorbate 80) required in protecting MAb1 from mechanical stress. Surfactants evaluated were non-ionic surfactants, Polysorbate 80, Polysorbate 20, Pluronic F-68 (polyoxyethylene-polyoxypropylene block polymer), Brij 35 (polyoxyethylene lauryl ether), Triton X-100, and an anionic surfactant, Caprylic acid (1-Heptanecarboxylic acid). After evaluating effect of surfactants and determining stabilizing effect of Polysorbate 80 against mechanical stress without compromising thermal and photostability of MAb1, the minimum concentration of Polysorbate 80 required for mechanical stability was further examined. Polysorbate 80 concentration was varied from 0 to 0.02%. Mechanical stability was evaluated by agitation of MAb1 at 300 rotations per minute at room temperature for 72 h. Samples were analyzed for purity by SEC-HPLC, turbidity by absorbance at 350 nm, visible particles by visual inspection, and sub-visible particles by light obscuration technique on a particle analyzer. All non-ionic surfactants tested showed a similar effect in protecting against mechanical stress and did not exhibit any significant negative effect on thermal and photostability. However, Caprylic acid had a slightly negative effect on mechanical and photostability when compared to the non-ionic surfactants or sample without surfactant. This work demonstrated that polysorbate 80 is better than other surfactants tested and that a concentration of at least 0.005% (w/v) Polysorbate 80 is needed to protect MAb1 against mechanical stress.

  2. Interactions between Surfactants in Solution and Electrospun Protein Fibers: Effects on Release Behavior and Fiber Properties.

    Science.gov (United States)

    Stephansen, Karen; García-Díaz, María; Jessen, Flemming; Chronakis, Ioannis S; Nielsen, Hanne M

    2016-03-07

    Intermolecular interaction phenomena occurring between endogenous compounds, such as proteins and bile salts, and electrospun compounds are so far unreported, despite the exposure of fibers to such biorelevant compounds when applied for biomedical purposes, e.g., tissue engineering, wound healing, and drug delivery. In the present study, we present a systematic investigation of how surfactants and proteins, as physiologically relevant components, interact with insulin-loaded fish sarcoplasmic protein (FSP) electrospun fibers (FSP-Ins fibers) in solution and thereby affect fiber properties such as accessible surface hydrophilicity, physical stability, and release characteristics of an encapsulated drug. Interactions between insulin-loaded protein fibers and five anionic surfactants (sodium taurocholate, sodium taurodeoxycholate, sodium glycocholate, sodium glycodeoxycholate, and sodium dodecyl sulfate), a cationic surfactant (benzalkonium chloride), and a neutral surfactant (Triton X-100) were studied. The anionic surfactants increased the insulin release in a concentration-dependent manner, whereas the neutral surfactant had no significant effect on the release. Interestingly, only minute amounts of insulin were released from the fibers when benzalkonium chloride was present. The FSP-Ins fibers appeared dense after incubation with this cationic surfactant, whereas high fiber porosity was observed after incubation with anionic or neutral surfactants. Contact angle measurements and staining with the hydrophobic dye 8-anilino-1-naphthalenesulfonic acid indicated that the FSP-Ins fibers were hydrophobic, and showed that the fiber surface properties were affected differently by the surfactants. Bovine serum albumin also affected insulin release in vitro, indicating that also proteins may affect the fiber performance in an in vivo setting.

  3. Acidity Constants Determination of Triazine Dye Derivative in the presence of some Surfactants by Multiwavelength Spectrophotometric and Spectrofluorimetric

    Directory of Open Access Journals (Sweden)

    Ali Yeganeh Faal

    2014-03-01

    Full Text Available In this work, acidity constants protonated form of 4.4'-bis astilbene-2,2'-disulfonic-disodium salts (TRIAZ have been determined spectrophotometrically and spectrofluorimetrically at 25◦C and ionic strength of 0.1M KNO3. A program based on MCR-ALS applied for determination of acidity constants. The results show that the peak values of dye are influenced by the presence of anionic, cationic, and nonionic surfactants. The effects of sodium dodecyl sulfate (SDS, Triton X-100 (TX-100 and cetyl trimethyl ammonium bromide (CTAB as a surface-active agent on the acidic and basic forms, and the spectral properties of dye were studied. Also, we determined the critical micelle concentration (CMC for these surfactants by spectrophotometric and spectrofluorimetric triazine dye probes. In addition, by using of evolving factor analysis (EFA and multivariate curve resolution alternative least squares (MCR-ALS methods, acidity constants were acquired.

  4. Synthesis and characterization of anionic/nonionic surfactant-interceded iron-doped TiO{sub 2} to enhance sorbent/photo-catalytic properties

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Ajit; Lee, Byeong-Kyu, E-mail: bklee@ulsan.ac.kr

    2015-09-15

    We investigated the synthesis, characterization, and application of surfactant-interceded Fe nanoparticle-doped TiO{sub 2} (TiO{sub 2}/Fe-S1 and TiO{sub 2}/Fe-S2) that were used as adsorbents and photo-catalysts for the removal of As(V) ions from aqueous media. Two types of surfactant (anionic (sodium dodecyl sulfate), S1 and non-ionic (Triton X-100), S2) were used to obtain the separation and mono-dispersion of Fe(III) ions in the reaction solution. The nanocomposites were characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), UV–vis, scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX) and elemental mapping analysis before and after As(V) removal. The Langmuir capacities (q{sub e}, mg/g) of the sodium dodecyl sulfate (SDS) and Triton X-100 interceded nanocomposites (TiO{sub 2}/Fe-S1 and TiO{sub 2}/Fe-S2, respectively) for arsenic removal were determined to be 65.79 and 50.76 mg/g, respectively, in aqueous media with As(V) concentration ranges of 0–10 mg/L at pH 6.5. - Highlights: • Fe(III) doped TiO{sub 2} nanocomposite was prepared with surfactant. • Anionic surfactant SDS enhanced the transfer of Fe(III) ions to TiO{sub 2}. • Surfactant-interceded nanocomposite enhanced As(V) removal. • Arsenic removal efficiency was as follows: dark phase>visible phase>UV region.

  5. Surfactant-enhanced bioremediation of PAH- and PCB-contaminated soils

    International Nuclear Information System (INIS)

    Ghosh, M.M.; Yeom, I.T.; Shi, Z.; Cox, C.D.; Robinson, K.G.

    1995-01-01

    The role of surfactants in the desorption of soil-bound polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) was investigated. The solubilization of individual PAHs in an extract of a weathered, coal tar-contaminated soil containing a mixture of PAHs and other petroleum derivatives was found to be significantly less than that for pure compounds. Batch soil washing with Triton X-100 (a commercial, nonionic alkyl phenol ethoxylate) was found to increase the effective diffusion rate of PAHs from the contaminated soil by four orders of magnitude compared to that obtained by gas purging when the results were analyzed using a radial diffusion model. At concentrations of up to 24 times its critical micelle concentration (CMC), Triton X-100 did not seem to enhance hydrocarbon degradation in the coal tar-contaminated soil; however, the biosurfactant rhamnolipid R1, at a concentration of 50x CMC, increased the rate of mineralization of 4,4'-chlorinated biphenyl mobilized from a laboratory-contaminated soil by more than 60 times

  6. Degradation of PAH in a creosote-contaminated soil. A comparison between the effects of willows (Salix viminalis), wheat straw and a nonionic surfactant.

    Science.gov (United States)

    Hultgren, Jenny; Pizzul, Leticia; Castillo, María del Pilar; Granhall, Ulf

    2010-01-01

    The degradation of polyaromatic hydrocarbons (PAH) in an aged creosote-contaminated soil in the presence of Salix viminalis was investigated in a greenhouse experiment. Phenanthrene and pyrene were degraded 100% and 80%, respectively, in the presence of plants but only 68% and 63% without plants. The effects of the nonionic surfactant Triton X-100 or the addition of straw, without plants, were also studied. The addition of straw had no effect on PAH degradation compared to the control Pyrene degradation with Triton X-100 at low concentrations (0.06 microl g(-1) DW) was comparable to that with plants but was less for anthracene and phenanthrene. The treatments with plants were, according to SIR measurements, dominated by active microorganisms (98.8% of the biomass), whereas all treatments without plants contained mostly dormant or non-growing microorganisms (1.7-2.0% active). Viable counts and active biomass were highly correlated in all treatments and demonstrated that S. viminalis greatly increased microbial populations. Dominant bacteria were grouped according to Gram, fluorescence and oxidase tests and revealed differences between treatments. The presence of S. viminalis or the surfactant enhanced PAH degradation, primarily by a rhizosphere effect on the microbial activity in the former case and by increased bioavailability in the latter case.

  7. Comparative study of the physicochemical properties of aqueous solutions of the hydrocarbon and fluorocarbon surfactants and their ternary mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Szymczyk, Katarzyna, E-mail: katarzyna.szymczyk@poczta.umcs.lublin.pl

    2014-03-03

    Highlights: • Acoustic properties of hydrocarbon and fluorocarbon surfactants were studied. • Auerbach’s relation is not proper for mixtures with fluorocarbon surfactants. • Values of the hydration number decreases at concentrations higher than CMC. • FSO100 and its mixtures are the strongest chaotropes. - Abstract: Speed of sound and density of aqueous solutions of hydrocarbon p-(1,1,3,3-tetramethylbutyl) phenoxypoly(ethyleneglycols) (Triton X-100 (TX100), Triton X-165 (TX165)) and fluorocarbon (Zonyl FSN-100 (FSN100), Zonyl FSO-100 (FSO100)) surfactants as well as their ternary mixtures were measured at 293 K. Taking into account these values and the literature data of the surface tension and viscosity of the studied systems, the values of the isentropic compressibility, apparent specific adiabatic compressibility, hydration number, apparent specific volume and Jones Dole’s A and B-coefficients were determined. For the systems containing FSO100 also the values of dB/dT were determined on the basis of the values of viscosity measured at different temperatures. Next, the calculated thermodynamic properties have been discussed in the term of intermolecular interactions between the components of the mixtures.

  8. Investigation of formation constant of complex of a new synthesized tripodal ligand with Cu2+ using rank annihilation factor analysis in surfactant media

    Directory of Open Access Journals (Sweden)

    R. Golbedaghi

    2014-01-01

    Full Text Available The complex formation between a newly synthesized tripodal ligand and the cation Cu2+ in water and surfactant media was studied spectrophotometrically using rank annihilation factor analysis (RAFA. According to molar ratio data the stoichiometry of complexation between the ligand and the cation Cu2+ was 1:1. Formation constant of this complex was derived using RAFA on spectrophotometric data. The performance of the method has been evaluated by using synthetic data. Also concentration and spectral profiles of ligand and complex can be obtained by using the stability constant and appropriate equations. The effect of surfactants such as sodium dodecyl sulfate (SDS, cetyltrimethylammonium bromide (CTAB and Triton X-100 on complex formation constant of Cu2+ with the ligand was investigated.

  9. pH dependent fluorescence switching in salicylideneaniline: ‘off–on–off’ operation controlled by surfactant micelles

    Energy Technology Data Exchange (ETDEWEB)

    Das, Diganta Kumar, E-mail: digkdas@yahoo.com; Dutta, Kaku

    2014-01-15

    Salaniline, a condensation product of salicylaldehyde and aniline, shows “off–on” fluorescent behaviour with pH in 1:1 (v/v) CH{sub 3}CN:H{sub 2}O and when 3% (w/v) anionic sodium dodecylsulphate (SDS) surfactant is present. The fluorescent switch behaviour of salaniline is forced to “off–on–off” type by 3% (w/v) neutral triton X-100 (TX-100) and 3% (w/v) cationic cetyltrimethylammonium bromide (CTAB) surfactant. The fluorescent “on” window is observed in the pH range 8.0–12.5 for TX-100 and 7.0–11.0 for CTAB. Different charge nature of the surfactants affects the protonation/deprotonation behaviour of salaniline differently, hence the photoinduced electron transfer (PET) processes and the fluorescent switch behaviour. -- Highlights: • Salicylideneaniline act as pH dependent “off–on” fluorescent switch in 1:1 (v/v) CH{sub 3}CN:H{sub 2}O. • In surfactant micelles TX-100 (neutral) and CTAB (positive) make the fluorescent switch “off–on–off” type while in. • In surfactant micelle SDS (negative) the pH dependent fluorescent switch is “off–on” type.

  10. FTIR AND NMR STUDIES OF ADSORBED TRITON X-114 IN MCM-41 MATERIALS

    Directory of Open Access Journals (Sweden)

    Paulina Taba

    2010-06-01

    Full Text Available One source of water pollutions is caused by the high use of surface-active agents (surfactants by industries and households. As a consequence, it is required to remove such substances from the environment One of the important and widely used methods for removal of substances from solution is adsorption. In this research, MCM-41 and its modification MCM41-TMCS were used to adsorb nonionic surfactant, Triton X-114. FTIR and NMR methods were used to study the interaction between the surfactants and the adsorbents. MCM-41 was synthesized hydrothermally at 100 oC and its modification was conducted by silylation of MCM-41 with trimethylchloro silane (MCM41-TMCS. Both unmodified and modified MCM-41 can adsorb the surfactant. The amount adsorbed in the unmodified material is higher than that in the modified one. The interaction of Triton X-114 with MCM-41 was hydrogen bonding between the silanol groups in MCM-41 and hydroxyl groups of Triton X-114. For modified samples, Triton X-114 interacted with alkylsilyl groups mostly through hydrophobic interaction. It is more likely that the interaction was through C12, C13, C26 and C27 of Triton X-114.    Keywords: FTIR, NMR, adsorbed Triton X-114, MCM-41 materials

  11. Effect of surfactant addition on ultrasonic leaching of trace elements from plant samples in inductively coupled plasma-atomic emission spectrometry

    Science.gov (United States)

    Borkowska-Burnecka, Jolanta; Jankowiak, Urszula; Zyrnicki, Wieslaw; Anna Wilk, Kazimiera

    2004-04-01

    The applicability of surfactants in sample preparation of plant materials followed by analysis by inductively coupled plasma atomic emission spectrometry has been examined. Reference materials (INCT-MPH-2-Mixed Polish Herbs, INCT-TL-1 black tea leaves and CTA-VTL-2 -Virginia tobacco leaves) and commercially available tea leaves were analyzed. Effects of addition surfactants (Triton X-100, didodecyldimethylammonium bromide and cetyltrimethylammonium bromide) on efficiency of ultrasonic leaching of elements from the plant samples and on plasma parameters were investigated. Low concentrations of the surfactants in solutions did not affect, in practice, analytical line intensities and the nebulization process. Quantitative recovery of some elements could be obtained by ultrasonic diluted acid leaching with the aid of surfactants. However, the element recovery depended on type of surfactant, as well as element and sample material. Plasma parameters, i.e. the excitation temperatures of Ar I, Fe II and Ca II as well as the electron number density and the Mg II/Mg I intensity ratio did not vary significantly due to the surfactants in solutions.

  12. Differential modulation of the chaperone-like activity of HSP-1/2, a major protein of horse seminal plasma by anionic and cationic surfactants.

    Science.gov (United States)

    Kumar, C Sudheer; Swamy, Musti J

    2017-03-01

    The major protein of equine seminal plasma, HSP-1/2 exhibits chaperone-like activity (CLA) by protecting various target proteins against thermal, chemical and oxidative stress. Polydispersity and surface hydrophobicity of HSP-1/2 were found to be important for its CLA. Surfactants are known to alter certain properties of proteins, e.g. hydrophobicity, charge and conformation either by altering properties of the medium or by direct binding. In the current study, thermal aggregation of alcohol dehydrogenase (ADH) and enolase has been studied in the presence of HSP-1/2, different surfactants and their combinations. The results obtained show that anionic surfactants (SDS, sodium dodecyl benzene sulfate) and neutral surfactants (tween-20, triton X-100) increase the CLA of HSP-1/2 and also inhibit aggregation of the target proteins independently. On the other hand, cationic surfactants (CTAB, alanine palmityl ester) increased the thermal aggregation of ADH and enolase and also decreased the CLA of HSP-1/2. These results are of significant interest as they show that surfactants such as SDS and tween-20 can potentially be used as anti-aggregation agents to prevent thermal aggregation of target proteins. Copyright © 2016 Elsevier B.V. All rights reserved.

  13. Effect of surfactants on the aggregation of pyronin B and pyronin Y in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Arik, Mustafa; Meral, Kadem [Department of Chemistry, Faculty of Sciences, Atatuerk University, 25240 Erzurum (Turkey); Onganer, Yavuz, E-mail: yonganer@atauni.edu.t [Department of Chemistry, Faculty of Sciences, Atatuerk University, 25240 Erzurum (Turkey)

    2009-06-15

    Molecular dynamics of pyronin B (PyB) and pyronin Y (PyY) in aqueous solution containing different surfactants were investigated by using absorption and fluorescence spectroscopy techniques. First, the interactions of PyB and PyY with the negatively charged surfactant sodium dodecyl sulphate (SDS) were investigated in the below and above critical micelle concentration (cmc). The H-aggregate formation of the dye compounds was observed for below the cmc of SDS surfactant. The absorbance of H-aggregate absorption band of PyB and PyY decreased according to the aggregate-monomer equilibrium by increasing SDS surfactant concentration towards the cmc. Therefore, equilibrium constants of the aggregate formation and oscillator strengths of monomer and aggregate of the dye compounds were calculated from spectral studies. Moreover, aggregate formation dynamics was discussed in terms of thermodynamic functions by using temperature studies. The interactions of PyB and PyY with the positively charged hexadecyltrimethylammonium bromide (CTAB) and neutral Triton X-100 (TX-100) were also studied and it was observed that there was no aggregate formation on the absorption and fluorescence spectra for below and above the cmc.

  14. Controlled synthesis of La1−xSrxCrO3 nanoparticles by hydrothermal method with nonionic surfactant and their ORR activity in alkaline medium

    International Nuclear Information System (INIS)

    Choi, Bo Hyun; Park, Shin-Ae; Park, Bong Kyu; Chun, Ho Hwan; Kim, Yong-Tae

    2013-01-01

    Graphical abstract: We demonstrate that Sr-doped LaCrO 3 nanoparticles were successfully prepared by the hydrothermal synthesis method using the nonionic surfactant Triton X-100 and the applicability of La 1−x Sr x CrO 3 to oxygen reduction reaction (ORR) electrocatalysis in an alkaline medium. Compared with the nanoparticles synthesized by the coprecipitation method, they showed enhanced ORR activity. - Highlights: • Sr-doped LaCrO 3 nanoparticles were successfully prepared by the hydrothermal method using the nonionic surfactant. • Homogeneously shaped and sized Sr-doped LaCrO 3 nanoparticles were readily obtained. • Compared with the nanoparticles synthesized by the coprecipitation method, they showed an enhanced ORR activity. • The main origin was revealed to be the decreased particle size due to the nonionic surfactant. - Abstract: Sr-doped LaCrO 3 nanoparticles were prepared by the hydrothermal method with the nonionic surfactant Triton X-100 followed by heat treatment at 1000 °C for 10 h. The obtained perovskite nanoparticles had smaller particle size (about 100 nm) and more uniform size distribution than those synthesized by the conventional coprecipitation method. On the other hand, it was identified with the material simulation that the electronic structure change by Sr doping was negligible, because the initially unfilled e g -band was not affected by the p-type doping. Finally, the perovskite nanoparticles synthesized by hydrothermal method showed much higher ORR activity by over 200% at 0.8 V vs. RHE than those by coprecipitation method

  15. Purification and spectroscopic characterization of photosystem II reaction center complexes isolated with or without Triton X-100.

    NARCIS (Netherlands)

    Eijckelhoff, C.; van Roon, H.; Groot, M.L.; van Grondelle, R.; Dekker, J.P.

    1996-01-01

    The pigment composition of the isolated photosystem II reaction center complex in its most stable and pure form currently is a matter of considerable debate. In this contribution, we present a new method based on a combination of gel filtration chromatography and diode array detection to analyze the

  16. Opposing Roles of the Staphylococcus aureus Virulence Regulators, Agr and Sar, in Triton X-100- and Penicillin-Induced Autolysis

    OpenAIRE

    Fujimoto, David F.; Bayles, Kenneth W.

    1998-01-01

    The regulation of murein hydrolases is a critical aspect of peptidoglycan growth and metabolism. In the present study, we demonstrate that mutations within the Staphylococcus aureus virulence factor regulatory genes, agr and sar, affect autolysis, resulting in decreased and increased autolysis rates, respectively. Zymographic analyses of these mutant strains suggest that agr and sar exert their effects on autolysis, in part, by modulating murein hydrolase expression and/or activity.

  17. Collisional Cascades Following Triton's Capture

    Science.gov (United States)

    Cuk, Matija; Hamilton, Douglas P.; Stewart-Mukhopadhyay, Sarah T.

    2017-10-01

    Neptune's moon Triton is widely thought to have been captured from heliocentric orbit, most likely through binary dissociation (Agnor and Hamilton, 2006). Triton's original eccentric orbit must have been subsequently circularized by satellite tides (Goldreich et al. 1989). Cuk and Gladman (2005) found that Kozai oscillations make early tidal evolution inefficient, and have proposed that collisions between Triton and debris from pre-existing satellites was the dominant mechanism of shrinking Triton's large post-capture orbit. However, Cuk and Hamilton (DPS 2016), using numerical simulations and results of Stewart and Leinhardt (2012), have found that collisions between regular satellites are unlikely to be destructive, while collisions between prograde moons and Triton are certainly erosive if not catastrophic. An obvious outcome would be pre-existing moon material gradually grinding down Triton and making it reaccrete in the local Laplace plane, in conflict with Triton's large current inclination. We propose that the crucial ingredient for understanding the early evolution of the Neptunian system are the collisions between the moons and the prograde and retrograde debris originating from the pre-existing moons and Triton. In particular, we expect early erosive impact(s) on Triton to generate debris that will, in subsequent collisions, disrupt the regular satellites. If the retrograde material were to dominate at some planetocentric distances, the end result may be a large cloud or disk of retrograde debris that would be accreted by Triton, shrinking Triton's orbit. Some of the prograde debris could survive in a compact disk interior to Triton's pericenter, eventually forming the inner moons of Neptune. We will present results of numerical modeling of these complex dynamical processes at the meeting.

  18. The reversed-flow gas chromatography technique as a tool for the study of the evaporation retardation of SO2 and (CH3)2S from water by soluble surfactants.

    Science.gov (United States)

    Sevastos, D; Kotsalos, E; Koliadima, A

    2017-02-01

    In the present work the evaporation retardation of SO 2 and (CH 3 ) 2 S (=DMS) from water by soluble surfactants was studied by the Reversed-Flow Gas Chromatography (R.F.G.C.) technique. Using suitable mathematical analysis, rate coefficients, k c , for the transfer of SO 2 and DMS from pure or artificial sea water to the atmospheric environment were determined in the presence or the absence of surfactants. The efficiency of the three surfactants used (CTAB, TRITON X-100 and SDS) to retard the evaporation rate of SO 2 and DMS from water was estimated by the decrease of the k c values in the presence of the three surfactants, compared to those in the absence of surfactants. The more efficient surfactant for the retardation evaporation of SO 2 from both the pure and the artificial sea water was found to be the cationic CTAB surfactant, as the maximum decreases of the k c values were found to be 4.61×10 -3 cms -1 (number of films, n=1) and 3.07×10 -3 cms -1 (n=3), respectively. On the other hand, more efficient surfactant for the retardation evaporation of DMS from pure water was found to be the non-ionic TRITON X-100, in which the decrease of the k c value was estimated to be 18.20×10 -3 cms -1 (n=3) and from artificial sea water the cationic CTAB surfactant in which the decrease of the k c value was found to be 8.24×10 -3 cms -1 (n=3). Finally, the precision of the R.F.G.C. method in studying the retardation effect of various surfactants in the transfer of SO 2 and DMS from the water body to the atmosphere is estimated (mean value 96.69%), and the experimental values of k c are compared with those given in the literature. Copyright © 2016 Elsevier B.V. All rights reserved.

  19. Influence of synthetic surfactants on the uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca

    Energy Technology Data Exchange (ETDEWEB)

    Masakorala, Kanaji [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom); Turner, Andrew [School of Earth, Ocean and Environmental Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)], E-mail: aturner@plymouth.ac.uk; Brown, Murray T. [School of Biological Sciences, University of Plymouth, Drake Circus, Plymouth PL4 8AA (United Kingdom)

    2008-12-15

    Uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca, has been studied in the presence of an anionic (sodium dodecyl sulphate, SDS), cationic (hexadecyltrimethylammonium bromide; HDTMA) and non-ionic (Triton X-100; TX) surfactant. Compared with the surfactant-free system, metal sorption was reduced in the presence of SDS or TX. Neither surfactant, however, had any measurable impact on cell membrane permeability, determined by leakage of dissolved free amino acids (DFAA), or on metal internalisation. We attribute these observations to the stabilisation of aqueous Cd and Pb by SDS and the shielding of otherwise amenable sorption sites by TX. Presence of HDTMA resulted in a reduction in the extent of both sorption and internalisation of all metals and a significant increase in the leakage of DFAA. Thus, by enhancing membrane permeability, HDTMA exerts the greatest influence on metal behaviour in the presence of U. lactuca. - Synthetic surfactants exert a significant impact on the uptake and internalisation of metals by a marine macroalga.

  20. Influence of synthetic surfactants on the uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca

    International Nuclear Information System (INIS)

    Masakorala, Kanaji; Turner, Andrew; Brown, Murray T.

    2008-01-01

    Uptake of Pd, Cd and Pb by the marine macroalga, Ulva lactuca, has been studied in the presence of an anionic (sodium dodecyl sulphate, SDS), cationic (hexadecyltrimethylammonium bromide; HDTMA) and non-ionic (Triton X-100; TX) surfactant. Compared with the surfactant-free system, metal sorption was reduced in the presence of SDS or TX. Neither surfactant, however, had any measurable impact on cell membrane permeability, determined by leakage of dissolved free amino acids (DFAA), or on metal internalisation. We attribute these observations to the stabilisation of aqueous Cd and Pb by SDS and the shielding of otherwise amenable sorption sites by TX. Presence of HDTMA resulted in a reduction in the extent of both sorption and internalisation of all metals and a significant increase in the leakage of DFAA. Thus, by enhancing membrane permeability, HDTMA exerts the greatest influence on metal behaviour in the presence of U. lactuca. - Synthetic surfactants exert a significant impact on the uptake and internalisation of metals by a marine macroalga

  1. Controlled synthesis of La{sub 1−x}Sr{sub x}CrO{sub 3} nanoparticles by hydrothermal method with nonionic surfactant and their ORR activity in alkaline medium

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Bo Hyun; Park, Shin-Ae [Energy System Major, School of Mechanical Engineering, Pusan National University, Busan 609-735 (Korea, Republic of); Park, Bong Kyu [GIFT Center, Pusan National University, Busan, 609-735 (Korea, Republic of); Chun, Ho Hwan, E-mail: chunahh@pusan.ac.kr [Global Core Research Center for Ships and Offshore Plants(GCRC-SOP), Pusan National University, Busan, 609-735 (Korea, Republic of); Kim, Yong-Tae, E-mail: yongtae@pusan.ac.kr [Energy System Major, School of Mechanical Engineering, Pusan National University, Busan 609-735 (Korea, Republic of)

    2013-10-15

    Graphical abstract: We demonstrate that Sr-doped LaCrO{sub 3} nanoparticles were successfully prepared by the hydrothermal synthesis method using the nonionic surfactant Triton X-100 and the applicability of La{sub 1−x}Sr{sub x}CrO{sub 3} to oxygen reduction reaction (ORR) electrocatalysis in an alkaline medium. Compared with the nanoparticles synthesized by the coprecipitation method, they showed enhanced ORR activity. - Highlights: • Sr-doped LaCrO{sub 3} nanoparticles were successfully prepared by the hydrothermal method using the nonionic surfactant. • Homogeneously shaped and sized Sr-doped LaCrO{sub 3} nanoparticles were readily obtained. • Compared with the nanoparticles synthesized by the coprecipitation method, they showed an enhanced ORR activity. • The main origin was revealed to be the decreased particle size due to the nonionic surfactant. - Abstract: Sr-doped LaCrO{sub 3} nanoparticles were prepared by the hydrothermal method with the nonionic surfactant Triton X-100 followed by heat treatment at 1000 °C for 10 h. The obtained perovskite nanoparticles had smaller particle size (about 100 nm) and more uniform size distribution than those synthesized by the conventional coprecipitation method. On the other hand, it was identified with the material simulation that the electronic structure change by Sr doping was negligible, because the initially unfilled e{sub g}-band was not affected by the p-type doping. Finally, the perovskite nanoparticles synthesized by hydrothermal method showed much higher ORR activity by over 200% at 0.8 V vs. RHE than those by coprecipitation method.

  2. The Combined Effects of Light-wind and Surfactants on Spilling Breakers

    Science.gov (United States)

    Duncan, J. H.; Liu, X.; Wang, D.

    2010-11-01

    Spilling breaking waves in the presence of light-winds and surfactants were studied experimentally in a wind-wave tank. The breaking waves were mechanically generated with a single wave maker motion that produces a weak spilling breaker in clean water without wind. Separate experiments were performed with the same wave maker motion and very low wind speeds in clean water and in water with various concentrations of Triton X-100 (a soluble surfactant). The crest-profiles of the waves along the center plane of the tank were measured with a cinematic laser-induced fluorescence technique. In clean water with a wind speed lower than 2.3 m/s (the minimum wind speed of wind-generated waves in our tank), the wave breaking is initiated with a bulge-capillary-ripple pattern. When the wind speed is above 2.3 m/s, wind waves are generated. These wind waves steepen on the front face of the crest of the mechanically generated waves and trigger breaking of these larger scale waves. In the presence of surfactants, the bulge-capillary-ripple pattern occurs at even higher wind speeds (3 m/s). Geometrical parameters describing the wave crest shape were found to scale with the wind speed to the third power.

  3. Temperature-dependent adsorption of surfactant molecules and associated crystallization kinetics of noncentrosymmetric Fe(IO{sub 3}){sub 3} nanorods in microemulsions

    Energy Technology Data Exchange (ETDEWEB)

    El-Kass, Moustafa [Université de Savoie, Laboratoire SYMME, BP 80439, 74944 Annecy Le Vieux Cedex (France); Ladj, Rachid [Université de Savoie, Laboratoire SYMME, BP 80439, 74944 Annecy Le Vieux Cedex (France); Université Lyon1, CNRS, UMR 5007, LAGEP, CPE, 43 bd 11 Novembre 1918, F-69622 Villeurbanne (France); Mugnier, Yannick, E-mail: Yannick.Mugnier@univ-savoie.fr [Université de Savoie, Laboratoire SYMME, BP 80439, 74944 Annecy Le Vieux Cedex (France); Le Dantec, Ronan [Université de Savoie, Laboratoire SYMME, BP 80439, 74944 Annecy Le Vieux Cedex (France); Hadji, Rachid [Institut Jean Lamour, UMR CNRS n°7198, Université de Lorraine, Nancy 1, BP 239, 54506 Vandoeuvre-lès-Nancy Cedex (France); Marty, Jean-Christophe [Université de Savoie, Laboratoire SYMME, BP 80439, 74944 Annecy Le Vieux Cedex (France); Rouxel, Didier [Institut Jean Lamour, UMR CNRS n°7198, Université de Lorraine, Nancy 1, BP 239, 54506 Vandoeuvre-lès-Nancy Cedex (France); Durand, Christiane [Université de Savoie, Laboratoire SYMME, BP 80439, 74944 Annecy Le Vieux Cedex (France); Fontvieille, Dominique [UMR CARRTEL (INRA/Université de Savoie), Laboratoire de Microbiologie Aquatique, BP 511, 74203 Thonon Cedex (France); Rogalska, Ewa [Structure et Réactivité des Systèmes Moléculaires Complexes, UMR 7565, Nancy Université, BP 70239, 54506 Vandoeuvre-lès-Nancy cedex (France); and others

    2013-11-15

    Graphical abstract: - Highlights: • Crystallization of Fe(IO{sub 3}){sub 3} in microemulsions probed by hyper-Rayleigh scattering. • A faster growth and a better shape control of nanorods are obtained at 80 °C. • Different persistent cell deformations are related to the crystallization kinetics. • A temperature-dependent adsorption of surfactants on nanorods is suggested. - Abstract: Aggregation-induced crystallization of iron iodate nanorods within organic–inorganic aggregates of primary amorphous precursors is probed by time-dependent hyper-Rayleigh scattering measurements in Triton X-100 based-microemulsions. In the context of a growing interest of noncentrosymmetric oxide nanomaterials in multi-photon bioimaging, we demonstrate by a combination of X-ray diffraction and electron microscopy that an increase in the synthesis of temperature results in faster crystallization kinetics and in a better shape-control of the final Fe(IO{sub 3}){sub 3} nanorods. For initial microemulsions of fixed composition, room-temperature synthesis leads to bundles of 1–3 μm long nanorods, whereas shorter individual nanorods are obtained when the temperature is increased. Results are interpreted in terms of kinetically unfavorable mesoscale transformations due to the strong binding interactions with Triton molecules. The interplay between the nanorod crystallization kinetics and their corresponding unit cell deformation, evidenced by lattice parameter refinements, is attributed to a temperature-dependent adsorption of surfactants molecules at the organic–inorganic interface.

  4. A novel aqueous micellar two-phase system composed of surfactant and sorbitol for purification of pectinase enzyme from Psidium guajava and recycling phase components.

    Science.gov (United States)

    Amid, Mehrnoush; Murshid, Fara Syazana; Manap, Mohd Yazid; Hussin, Muhaini

    2015-01-01

    A novel aqueous two-phase system composed of a surfactant and sorbitol was employed for the first time to purify pectinase from Psidium guajava. The influences of different parameters, including the type and concentration of the surfactant and the concentration and composition of the surfactant/sorbitol ratio, on the partitioning behavior and recovery of pectinase were investigated. Moreover, the effects of system pH and the crude load on purification fold and the yield of purified pectinase were studied. The experimental results indicated that the pectinase was partitioned into surfactant-rich top phase, and the impurities were partitioned into the sorbitol-rich bottom phase with the novel method involving an ATPS composed of 26% (w/w) Triton X-100 and 23% (w/w) sorbitol at 54.2% of the TLL crude load of 20% (w/w) at pH 6.0. The enzyme was successfully recovered by this method with a high purification factor of 15.2 and a yield of 98.3%, whereas the phase components were also recovered and recycled at rates above 96%. This study demonstrated that this novel ATPS method can be used as an efficient and economical alternative to the traditional ATPS for the purification and recovery of the valuable enzyme.

  5. A Novel Aqueous Micellar Two-Phase System Composed of Surfactant and Sorbitol for Purification of Pectinase Enzyme from Psidium guajava and Recycling Phase Components

    Science.gov (United States)

    Murshid, Fara Syazana; Manap, Mohd Yazid; Hussin, Muhaini

    2015-01-01

    A novel aqueous two-phase system composed of a surfactant and sorbitol was employed for the first time to purify pectinase from Psidium guajava. The influences of different parameters, including the type and concentration of the surfactant and the concentration and composition of the surfactant/sorbitol ratio, on the partitioning behavior and recovery of pectinase were investigated. Moreover, the effects of system pH and the crude load on purification fold and the yield of purified pectinase were studied. The experimental results indicated that the pectinase was partitioned into surfactant-rich top phase, and the impurities were partitioned into the sorbitol-rich bottom phase with the novel method involving an ATPS composed of 26% (w/w) Triton X-100 and 23% (w/w) sorbitol at 54.2% of the TLL crude load of 20% (w/w) at pH 6.0. The enzyme was successfully recovered by this method with a high purification factor of 15.2 and a yield of 98.3%, whereas the phase components were also recovered and recycled at rates above 96%. This study demonstrated that this novel ATPS method can be used as an efficient and economical alternative to the traditional ATPS for the purification and recovery of the valuable enzyme. PMID:25756051

  6. Effect of xylanase, urea, Tween and Triton additives on bioethanol production of corn stover

    Science.gov (United States)

    Xin, Xiu; Lu, Jie; Yang, Rui-Feng; Song, Wen-jing; Li, Hai-ming; Wang, Hai-song; Zhou, Jing-hui

    2017-03-01

    Corn stover is a potential source of renewable biomass for conversion to bioethanol. Fed-batch semi-simultaneous saccharifcation and fermentation (S-SSF) of corn stover pretreated by liquid hot water (LHW) was investigated. The present study aimed to confirm the influence of xylanase, urea, Tween and Triton additives on bioethanol. Results show that the positive effect of xylanase, urea, Tween was observed. High ethanol concentration requires the addition of xylanase in the stage of saccharification. The optimal amount of xylanase was 0.2 g/g biomass and addition of Triton (Triton X-100) increases the effect of xylanase. Urea has a promotion effect on the whole fermentation process.When adding 0.1% urea in the fermentation stage,the best promoting rate is 24.2%. In the longitudinal comparison of the Tween series, under the same experimental conditions, the promoting effect of Tween series: Tween 40 > Tween 80 > Tween 20 > Tween 60.

  7. Indication of critical micelle concentration of nonionic surfactants with large emission change using water-soluble conjugated polymer as molecular light switch

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Lilin, E-mail: sunlilin126@126.com [Anhui Key Laboratory of Chemo-Biosensing, College of Chemistry and Materials Science, Anhui Normal University, Wuhu 241000 (China); Hao, Dan; Zhang, Ping; Qian, Zhangsheng; Shen, Weili [Anhui Key Laboratory of Chemo-Biosensing, College of Chemistry and Materials Science, Anhui Normal University, Wuhu 241000 (China); Shao, Taili [Anhui Key Laboratory of Chemo-Biosensing, College of Chemistry and Materials Science, Anhui Normal University, Wuhu 241000 (China); Department of Pharmacy, Wannan Medical College, Wuhu 241000 (China); Zhu, Changqing, E-mail: zhucq@mail.ahnu.edu.cn [Anhui Key Laboratory of Chemo-Biosensing, College of Chemistry and Materials Science, Anhui Normal University, Wuhu 241000 (China)

    2013-02-15

    A new near-infrared water-soluble conjugated polymer, i.e. poly [2,5-di (propyloxysulfonate)-1,4-phenylene-ethynylene-9,10-anthrylene] (PPEASO3) was synthesized to investigate its interaction with surfactants. It was found that PPEASO3 has only a weak fluorescence emission at about 670 nm due to its self-aggregation in water and in aqueous solution containing a low concentration of nonionic surfactants, i.e. below their critical micelle concentration (CMC). However, a dramatic fluorescence enhancement with a large emission blue-shift (>40 nm) was found once the concentration of nonionic surfactants reached the CMC (especially for Triton X-100). An orange fluorescence could be observed even with naked-eyes under UV-lamp, which gave a direct indication for the micelle forming process and provided a simple method for the CMC determination of the nonionic surfactants. The CMC values determined by this method were in good agreement with those obtained by other techniques. The dramatic emission change observed could be ascribed to the intensive hydrophobic interaction between PPEASO3 and surfactants micelle, which greatly disrupts the aggregation of the polymer and increase the fluorescence efficiency of PPEASO3. Highlights: Black-Right-Pointing-Pointer Investigated the interaction of a new water-soluble conjugated polymer with surfactants. Black-Right-Pointing-Pointer The dramatic fluorescence enhancement and emission blue-shift were observed at the CMC. Black-Right-Pointing-Pointer The obvious emission color change could be observed with naked-eyes under UV-lamp. Black-Right-Pointing-Pointer Gave a direct indication for the micelle forming process. Black-Right-Pointing-Pointer Provided a simple method for the CMC determination of the nonionic surfactants.

  8. Study of the influence of surfactants on the activity coefficients and mass transfer coefficients of methanol in aqueous mixtures by reversed-flow gas chromatography.

    Science.gov (United States)

    Kotsalos, Efthimios; Brezovska, Boryana; Sevastos, Dimitrios; Vagena, Artemis; Koliadima, Athanasia; Kapolos, John; Karaiskakis, George

    2017-11-17

    This work focuses on the influences of surfactants on the activity coefficients, γ, of methanol in binary mixtures with water, as well as on the mass transfer coefficients, k c , for the evaporation of methanol, which is a ubiquitous component in the troposphere, from mixtures of methanol with water at various surfactant's and methanol's concentrations. The technique used is the Reversed-Flow Gas Chromatography (R.F.G.C.), a version of Inverse Gas Chromatography, which allows determining both parameters by performing only one experiment for the k c parameter and two experiments for the γ parameter. The k c and γ values decrease in the presence of the three surfactants used (CTAB, SDS, TRITON X-100) at all methanol's and surfactant's concentrations. The decrease in the methanol's molar fraction, at constant number of surfactant films leads to a decrease in the k c and γ values, while the decrease in the surfactant's concentration, at constant methanol's molar fraction leads to an increase in both the k c and γ parameters. Mass transfer coefficients for the evaporation of methanol at the surfactant films, are also calculated which are approximately between 4 and 5 orders of magnitude larger than the corresponding mass transfer coefficients at the liquid films. Finally, thicknesses of the boundary layer of methanol in the mixtures of methanol with water were determined. The quantities found are compared with those given in the literature or calculated theoretically using various empirical equations. The precision of the R.F.G.C. method for measuring γ and k c parameters is approximately high (94.3-98.0%), showing that R.F.G.C. can be used with success not only for the thermodynamic study of solutions, but also for the interphase transport. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Iron selenide films by aerosol assisted chemical vapor deposition from single source organometallic precursor in the presence of surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Hussain, Raja Azadar [Department of Chemistry, Quaid-i-Azam University, 45320 Islamabad (Pakistan); Badshah, Amin, E-mail: aminbadshah@yahoo.com [Department of Chemistry, Quaid-i-Azam University, 45320 Islamabad (Pakistan); Younis, Adnan [School of Materials Science and Engineering, University of New South Wales, Sydney 2052, NSW (Australia); Khan, Malik Dilshad [Department of Chemistry, Quaid-i-Azam University, 45320 Islamabad (Pakistan); Akhtar, Javeed [Department of Physics, COMSATS Institute of Information Technology, Park Road, Chak Shahzad, Islamabad (Pakistan)

    2014-09-30

    This article presents the synthesis and characterization (multinuclear nuclear magnetic resonance, Fourier transform infrared spectroscopy, carbon–hydrogen–nitrogen–sulfur analyzer, atomic absorption spectrometry and thermogravimetric analysis) of a single source organometallic precursor namely 1-acetyl-3-(4-ferrocenylphenyl)selenourea for the fabrication of iron selenide (FeSe) films on glass substrates using aerosol assisted chemical vapor deposition (AACVD). The changes in the morphologies of the films have been monitored by the use of two different surfactants i.e. triton X-100 and tetraoctylphosphonium bromide during AACVD. The role of surfactant has been evaluated by examining the interaction of the surfactants with the precursor by using UV–vis spectroscopy and cyclic voltammetry. The fabricated FeSe films have been characterized with powder X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy. - Highlights: • Ferrocene incorporated selenourea (FIS) has been synthesized and characterized. • FeSe thin films have been fabricated from FIS. • Mechanism of film growth was studied with cyclic voltammetry and UV–vis spectroscopy.

  10. Surfactant-assisted hydrothermal synthesis of TiO2/reduced graphene oxide nanocomposites and their photocatalytic performances

    Science.gov (United States)

    Hu, Ju; Li, Hansheng; Muhammad, Sohail; Wu, Qin; Zhao, Yun; Jiao, Qingze

    2017-09-01

    Titanium dioxide/reduced graphene oxide nanocomposites (TiO2/RGO-X, X=S, T or C, was denoted sodium dodecyl benzene sulfonate, Triton X-100 and cetyl trimethyl ammonium bromide, respectively) were synthesized using a one-step surfactant-assisted hydrothermal method. The characterization of phase structure and morphology of the as-obtained nanocomposites reveals that TiO2 in the TiO2/RGO-X exhibits the morphologies of nanoparticles, nanowires and array-like nanowires on the surface of RGO, respectively. Compared with the control TiO2/RGO nanocomposite, TiO2/RGO-X presents an excellent photocatalytic activity. With uniform array-like TiO2 nanowires on the surface of RGO, the TiO2/RGO-C shows a significant enhancement in the photocatalytic efficiency. Besides, a deeper insight into the growth mechanism of TiO2/RGO nanocomposites is put forward. This work indicates that the surfactant-assisted hydrothermal method is an effective approach to improve the structure, morphology and photocatalytic performance of TiO2/RGO composites. Moreover, the surfactants with various types can interact with the precursors of TiO2 and RGO in different ways.

  11. Triton's streaks as windblown dust

    Science.gov (United States)

    Sagan, Carl; Chyba, Christopher

    1990-01-01

    Explanations for the surface streaks observed by Voyager 2 on Triton's southern hemisphere are discussed. It is shown that, despite Triton's tenuous atmosphere, low-cohesion dust trains with diameters of about 5 micron or less may be carried into suspension by aeolian surface shear stress, given expected geostrophic wind speeds of about 10 m/s. For geyser-like erupting dust plumes, it is shown that dust-settling time scales and expected wind velocities can produce streaks with length scales in good agreement with those of the streaks. Thus, both geyserlike eruptions or direct lifting by surface winds appear to be viable mechanisms for the origin of the streaks.

  12. Color and chemistry on Triton

    Science.gov (United States)

    Thompson, W. Reid; Sagan, Carl

    1990-01-01

    The surface of Triton is very bright but shows subtle yellow to peach hues which probably arise from the production of colored organic compounds from CH4 + N2 and other simple species. In order to investigate possible relationships between chemical processes and the observed surface distribution of chromophores, the surface units are classified according to color/albedo properties, the rates of production of organic chromophores by the action of ultraviolet light and high-energy charged particles is estimated, and rates, spectral properties, and expected seasonal redistribution processes are compared to suggest possible origins of the colors seen on Triton's surface.

  13. Soil remediation: humic acids as natural surfactants in the washings of highly contaminated soils

    International Nuclear Information System (INIS)

    Conte, Pellegrino; Agretto, Anna; Spaccini, Riccardo; Piccolo, Alessandro

    2005-01-01

    The remediation of the highly contaminated site around the former chemical plant of ACNA (near Savona) in Northern Italy is a top priority in Italy. The aim of the present work was to contribute in finding innovative and environmental-friendly technology to remediate soils from the ACNA contaminated site. Two soils sampled from the ACNA site (A and B), differing in texture and amount and type of organic contaminants, were subjected to soil washings by comparing the removal efficiency of water, two synthetic surfactants, sodium dodecylsulphate (SDS) and Triton X-100 (TX100), and a solution of a natural surfactant, a humic acid (HA) at its critical micelle concentration (CMC). The extraction of pollutants by sonication and soxhlet was conducted before and after the soil washings. Soil A was richer in polycyclic aromatic hydrocarbons, whereas soil B had a larger content of thiophenes. Sonication resulted more analytically efficient in the fine-textured soil B. The coarse-textured soil A was extracted with a general equal efficiency also by soxhlet. Clean-up by water was unable to exhaustively remove contaminants from the two soils, whereas all the organic surfactants revealed very similar efficiencies (up to 90%) in the removal of the contaminants from the soils. Hence, the use of solutions of natural HAs appears as a better choice for soil washings of highly polluted soils due to their additional capacity to promote microbial activity, in contrast to synthetic surfactants, for a further natural attenuation in washed soils. - Solutions of natural humic acids appear to be a better choice for washing highly polluted soils

  14. Redesigning TRACER trial after TRITON.

    Science.gov (United States)

    Serebruany, Victor L

    2015-10-15

    Designing of smart clinical trials is critical for regulatory approval and future drug utilization. Importantly, trial design should be reconsidered if the interim analyses suggest unexpected harm, or conflicting results were yielded from the other trials within the same therapeutic area. With regard to antiplatelet agents, the perfect example is redesigning of the ongoing PRoFESS trial by eliminating aspirin from clopidogrel arm after the earlier MATCH trial results became available. The goal was to aseess the unchanged TRACER trial design in light of the evidence yielded from the earlier completed TRITON trial. TRACER was designed as a triple versus dual antiplatelet trial in NSTEMI patients with no previous long-term outcome data supporting such aggressive strategy. TRITON data represented dual versus dual antiplatelet therapy, and became available before TRACER enrollment starts revealing prasugrel front-loaded early vascular benefit predominantly in STEMI patients with the growing over time bleeding and cancer risks. Moreover, large prasugrel NSTEMI TRITON cohort exhibited trend towards excess mortality in experimental arm warning against aggressive TRACER design. The long-term TRITON results in general, and especially in the NSTEMI patients challenge unchanged TRACER trial design. Applying dual, rather than triple antiplatelet therapy protocol modification should be considered in TRACER to minimize bleeding, cancer, and non-cardiovascular death risks. Copyright © 2015. Published by Elsevier Ireland Ltd.

  15. Description of the Triton reactor; Pile Triton, rapport descriptif

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1967-09-01

    The Triton reactor is an enriched uranium pool type reactor. It began operation in 1959, after a divergence made on the June 30 the same year. Devoted to studies of radiation protection, its core can be displaced in the longitudinal direction. The pool can be separated in two unequal compartments by a wall. The Triton core is placed in a small compartment, the Nereide core in the big compartment. A third compartment without water is called Naiade II, is separated by a concrete wall in which is made a window closed by an aluminium plate (2.50 m x 2.70 m). The Naiade II hole is useful for protection experiments using the Nereide core. After a complete refitting, the power of the triton reactor that reached progressively from 1.2 MW to 2 MW, then 3 MW has reached in August 1965 6.5 MW. The reactor has been specialized in irradiations in fix position, the core become fix, the nereide core has been hung mobile. Since it has been used for structure materials irradiation, for radioelements fabrication and fundamental research. The following descriptions are valid for the period after August 1965. [French] Le reacteur Triton est un reacteur piscine, a uranium enrichi. Il est entre en fonctionnement en 1959, apres une divergence effectuee le 30 juin de cette meme annee. Destine a des etudes de protection contre les rayonnements, son coeur pouvait se deplacer dans le sens longitudinal. La piscine peut etre separee en deux compartiments inegaux par un batardeau. Le coeur triton est place dans le petit compartiment, le coeur Nereide dans le grand compartiment. Un troisieme compartiment sans eau, appele Naiade II, est separe par une paroi en beton dans laquelle est amenagee une fenetre obturee par une plaque d'aluminium (2,50 m x 2,70 m). La fosse Naiade II sert a des experiences de protection utilisant le coeur nereide. Apres une refonte complete, la puissance du reacteur triton qui etait passee progressivement de 1,2 MW a 2 MW, puis 3 MW, a atteint en aout 1965 6, 5 MW

  16. Determination of a method for extraction of coenzyme Q10 in human plasma: optimization of the use of surfactants and other variables

    Directory of Open Access Journals (Sweden)

    Claudia Cristina Ferreiro-Barros

    2012-06-01

    Full Text Available Objective: To establish a routine for the extraction of the total levelsof CoQ10 in human plasma through the Ultra High Performance LiquidChromatography (UHPLC. Methods: Two extraction protocolswere tested: a methanol: hexane and b 1-propanol. The followingparameters were analyzed: extraction temperature (19ºC and 4ºC,extraction tubes (glass and polypropylene, and surfactants (SDS,Triton X-100, Tween-20 at different concentrations, i.e., 1%,3%, 5% and 10%. Results: The results showed that the methodof extraction of CoQ10 in a sample of human plasma at 4ºC, usingsolvents methanol: hexane (85:15, v/v in the presence of surfactantTween-20 at 3% and polypropylene tubes showed better efficiencyand reproducibility when compared to the method with 1-propanol.Conclusion: By the analyses performed, it was possible to observethat the addition of the surfactant Tween-20 promoted an increasein the recovery of CoQ10 by the methanol:hexane extraction method.This method showed good reproducibility, with a low coefficient ofvariation and high sensitivity, since CoQ10 was detected in samplesof plasma of a control individual using a UV-type detector. The useof UHPLC equipment allowed a total analysis with total run time of3.5 minutes, enabling the rapid achievement of results, consideredmandatory for laboratory routines.

  17. Natural Surfactant Enrichments in the Atlantic Ocean Between 50°N and 50°S: Data from the Atlantic Meridional Transect, Oct-Nov 2014

    Science.gov (United States)

    Sabbaghzadeh, B.; Upstill-Goddard, R. C.; Nightingale, P. D.; Beale, R.

    2016-02-01

    Surfactants that decrease air-sea gas exchange by suppressing the gas transfer velocity (kw) show variable enrichments in the sea surface microlayer (SML) relative to the underlying water. This reflects variability in the rates of surfactant production and consumption. Total surfactant activity (SA: equivalent to Triton-X-100, mgL -1) was determined daily between the UK and the Falkland Islands, during cruise 24 of the Atlantic Meridional Transect programme (AMT 24). Samples were simultaneously obtained from the SML (Garrett screen), from the ship's underway system (inlet at 7m) and in hydrocasts to 500m. SA analysis was by hanging mercury drop electrode polarography (Metrohm 797 VA Computrace). SA enrichment factors (EF: SML SA / underlying water SA) >1 were observed at most locations, showing the SML to be consistently SA-enriched along the entire cruise transect. The persistence of these enrichments up to wind speeds 12m s-¹ support previous conclusions regarding the stability of the SML under high winds. More specifically, SA in the SML was up to four-fold higher in the Atlantic Northern Hemisphere than in the Atlantic Southern Hemisphere. Even so, EF values were not significantly different between the two hemispheres (p >0.05). These various findings have potentially important implications for kw variability across ocean basin scales.

  18. Exploring Triton with multiple landers

    Science.gov (United States)

    Balint, Tibor S.

    2005-01-01

    In our pathway for Outer Planetary Exploration several mission concepts were considered, based on the proposed JIMO mission architecture. This paper describes a JIMO follow-on mission concept to Neptunes largest moon. Triton is a target of interest for outer solar system studies. It has a highly inclined retrograde orbit, suggesting that it may have been a Kuiper Belt object captured by Neptune. Given this assumption its composition, which may include organic materials, would be of significant scientific interest.

  19. Description of the Triton reactor

    International Nuclear Information System (INIS)

    1967-09-01

    The Triton reactor is an enriched uranium pool type reactor. It began operation in 1959, after a divergence made on the June 30 the same year. Devoted to studies of radiation protection, its core can be displaced in the longitudinal direction. The pool can be separated in two unequal compartments by a wall. The Triton core is placed in a small compartment, the Nereide core in the big compartment. A third compartment without water is called Naiade II, is separated by a concrete wall in which is made a window closed by an aluminium plate (2.50 m x 2.70 m). The Naiade II hole is useful for protection experiments using the Nereide core. After a complete refitting, the power of the triton reactor that reached progressively from 1.2 MW to 2 MW, then 3 MW has reached in August 1965 6.5 MW. The reactor has been specialized in irradiations in fix position, the core become fix, the nereide core has been hung mobile. Since it has been used for structure materials irradiation, for radioelements fabrication and fundamental research. The following descriptions are valid for the period after August 1965 [fr

  20. Effect of presence of benzene ring in surfactant hydrophobic chain on the transformation towards one dimensional aggregate

    Directory of Open Access Journals (Sweden)

    Rabah A. Khalil

    2015-07-01

    Full Text Available The formation of wormlike micelle and the following significant changes in rheological properties suffer misunderstanding from both theoretical and fundamental aspects. Recently, we have introduced a theory for interpreting such important phenomenon which is referred to as critical intermolecular forces (CIF. The theory has stated that the hydrophobic effect is the main factor for the formation of worm-like aggregates. Therefore, it seems interesting to check out the validity of this new physical insight through investigating the presence of benzene ring as less hydrophobic group in contrast to that of alkyl in surfactant tail. The mixture of anionic sodium dodecylbenzenesulphonate (SDBS and cationic cetyltrimethylammonium bromide (CTAB shows a high dynamic viscosity peak at the ratio of 80/20 of 3 wt.% CTAB/SDBS indicating the formation of wormlike micelles. The thermodynamic properties have been evaluated for this mixture exhibiting good agreement with the rheological changes. Interestingly, the results show the presence of benzene ring (in SDBS causing a negative effect towards the formation of one dimensional aggregate in contrast to previous results which support the proposed CIF theory. The presence of nonionic surfactant TritonX-100 in binary and ternary systems of SDBS and CTAB prohibits the formation of wormlike micelles.

  1. Magnetic surfactants

    OpenAIRE

    Brown, P.; Alan Hatton, T.; Eastoe, J.

    2015-01-01

    Surfactants are ubiquitous, being important commodity chemicals with wide industrial applications, and essential components of living organisms. With stimuli-responsive surfactants, self-assembly and physicochemical properties of a wide variety of materials may be readily manipulated, both reversibly and irreversibly. Until recently, magnetically responsive surfactants had not been reported. This review reports the recent progress in magnetoresponsive surfactants, covering control of interfac...

  2. Mixed micelles of polyethylene glycol (23) lauryl ether with ionic surfactants studied by proton 1D and 2D NMR.

    Science.gov (United States)

    Gao, Hong-Chang; Zhao, Sui; Mao, Shi-Zhen; Yuan, Han-Zhen; Yu, Jia-Yong; Shen, Lian-Fang; Du, You-Ru

    2002-05-01

    (1)H NMR chemical shift, spin-lattice relaxation time, spin-spin relaxation time, self-diffusion coefficient, and two-dimensional nuclear Overhauser enhancement (2D NOESY) measurements have been used to study the nonionic-ionic surfactant mixed micelles. Cetyl trimethyl ammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) were used as the ionic surfactants and polyethylene glycol (23) lauryl ether (Brij-35) as the nonionic surfactant. The two systems are both with varying molar ratios of CTAB/Brij-35 (C/B) and SDS/Brij-35 (S/B) ranging from 0.5 to 2, respectively, at a constant concentration of 6 mM for Brij-35 in aqueous solutions. Results give information about the relative arrangement of the surfactant molecules in the mixed micelles. In the former system, the trimethyl groups attached to the polar heads of the CTAB molecules are located between the first oxy-ethylene groups next to the hydrophobic chains of Brij-35 molecules. These oxy-ethylene groups gradually move outward from the hydrophobic core of the mixed micelle with an increase in C/B in the mixed solution. In contrast to the case of the CTAB/Triton X-100 system, the long flexible hydrophilic poly oxy-ethylene chains, which are in the exterior part of the mixed micelles, remain coiled, but looser, surrounding the hydrophobic core. There is almost no variation in conformation of the hydrophilic chains of Brij-35 molecules in the mixed micelles of the SDS/Brij-35 system as the S/B increases. The hydrophobic chains of both CTAB and SDS are co-aggregated with Brij-35, respectively, in their mixed micellar cores.

  3. A novel liquid/liquid extraction process composed of surfactant and acetonitrile for purification of polygalacturonase enzyme from Durio zibethinus.

    Science.gov (United States)

    Amid, Mehrnoush; Manap, Yazid; Azmira, Farhana; Hussin, Muhaini; Sarker, Zaidul Islam

    2015-07-01

    Polygalacturonase is one of the important enzymes used in various industries such as food, detergent, pharmaceutical, textile, pulp and paper. A novel liquid/liquid extraction process composed of surfactant and acetonitrile was employed for the first time to purify polygalacturonase from Durio zibethinus. The influences of different parameters such as type and concentration of surfactants, concentrations of acetonitrile and composition of surfactant/acetonitrile on partitioning behavior and recovery of polygalacturonase was investigated. Moreover, the effect of pH of system and crude load on purification fold and yield of purified polygalacturonase were studied. The results of the experiment indicated the polygalacturonase was partitioned into surfactant top rich phase with impurities being partitioned into acetonitrile bottom rich phase in the novel method of liquid/liquid process composed of 23% (w/w) Triton X-100 and 19% (w/w) acetonitrile, at 55.6% of TLL (tie line length) crude load of 25% (w/w) at pH 6.0. Recovery and recycling of components also was measured in each successive step of liquid/liquid extraction process. The enzyme was successfully recovered by the method with a high purification factor of 14.3 and yield of 97.3% while phase components were also recovered and recycled above 95%. This study demonstrated that the novel method of liquid/liquid extraction process can be used as an efficient and economical extraction method rather than the traditional methods of extraction for the purification and recovery of the valuable enzyme. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. A Surfactant-Induced Functional Modulation of a Global Virulence Regulator from Staphylococcus aureus.

    Directory of Open Access Journals (Sweden)

    Sukhendu Mandal

    Full Text Available Triton X-100 (TX-100, a useful non-ionic surfactant, reduced the methicillin resistance in Staphylococcus aureus significantly. Many S. aureus proteins were expressed in the presence of TX-100. SarA, one of the TX-100-induced proteins, acts as a global virulence regulator in S. aureus. To understand the effects of TX-100 on the structure, and function of SarA, a recombinant S. aureus SarA (rSarA and its derivative (C9W have been investigated in the presence of varying concentrations of this surfactant using various probes. Our data have revealed that both rSarA and C9W bind to the cognate DNA with nearly similar affinity in the absence of TX-100. Interestingly, their DNA binding activities have been significantly increased in the presence of pre-micellar concentration of TX-100. The increase of TX-100 concentrations to micellar or post-micellar concentration did not greatly enhance their activities further. TX-100 molecules have altered the secondary and tertiary structures of both proteins to some extents. Size of the rSarA-TX-100 complex appears to be intermediate to those of rSarA and TX-100. Additional analyses show a relatively moderate interaction between C9W and TX-100. Binding of TX-100 to C9W has, however, occurred by a cooperative pathway particularly at micellar and higher concentrations of this surfactant. Taken together, TX-100-induced structural alteration of rSarA and C9W might be responsible for their increased DNA binding activity. As TX-100 has stabilized the somewhat weaker SarA-DNA complex effectively, it could be used to study its structure in the future.

  5. Photophysics of a solvent sensitive keto-tetrahydrocarbazole based fluorophore and its interaction with triethylamine: A spectroscopic inquest under surfactant and β-CD confinement

    Science.gov (United States)

    Mitra, Amrit Krishna; Ghosh, Sujay; Sarangi, Manas Kumar; Chakraborty, Suchandra; Saha, Chandan; Basu, Samita

    2014-09-01

    In this communication, we wish to report solution phase photophysics of 6,7-dimethoxy-3-methyl-2,3,4,9-tetrahydro-1H-carbazol-1-one (DMMTCO) and its interaction with a simple aliphatic organic donor, triethylamine (TEA) in different environments using absorption, steady-state and time-resolved fluorescence techniques. We have chosen ten solvents of varied nature and have observed that the fluorescence emission maximum of the compound is sensitive to the ET(30) value of the solvent. Quantum yield of the fluorophore is found to be higher in polar aprotic solvents like DMSO, DMF and ACN. When the fluorophore interacts with an anionic surfactant solution of sodium dodecyl sulphate (SDS), a hypsochromic shift of 17 nm is observed with respect to pure aqueous medium as the concentration of the surfactant increases. On switching over to the neutral surfactant of Triton X-100, a hypsochromic shift of 29 nm with respect to pure aqueous medium is witnessed as the concentration surges. Likewise, with the increase in concentration of β-cyclodextrin, we have noted a hypsochromic shift of 26 nm. In all of the above mentioned occasions, we have perceived hypsochromic shifts along with concomitant increase in fluorescence intensity. These observations regarding the organised media indicate that the immediate surrounding around the probe gets modified with the increase in surfactant and β-cyclodextrin concentration. TEA is a simple organic molecule that interacts with DMMTCO in a differing manner when we change the atmosphere from purely homogeneous to surfactant environment. In the confined medium, we observe the formation of a ground state complex, which is not that much appreciable in the case of homogeneous solvents.

  6. Thermophysical and spectroscopic studies of room temperature ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate in Tritons

    International Nuclear Information System (INIS)

    Chaudhary, Ganga Ram; Bansal, Shafila; Mehta, S.K.; Ahluwalia, A.S.

    2012-01-01

    Highlights: ► Thermophysical studies of new formulations of [BMIM][PF 6 ]+TX(45,100) have been made. ► Strong intermolecular interactions between [BMIM][PF 6 ] and TX (45, 100) is observed. ► Magnitude of interactions increases with the addition of oxyethylene groups in TX. ► With rise in temperature, intermolecular interactions increases. ► Spectroscopic studies show that interactions are via aromatic rings of RTIL and TX. - Abstract: The thermophysical properties viz. density ρ, speed of sound u, and specific conductivity κ of pure room temperature ionic liquid (1-butyl-3-methylimidazolium hexafluorophosphate) and its binary formulations with Triton X-45 and Triton X-100 have been studied over the entire composition range at different temperatures (293.15 to 323.15) K. Excess molar volume V E , deviation in isentropic compressibility ΔK S , partial molar excess volume V i E , deviation in partial molar isentropic compressibility ΔK S,i , deviation in specific conductivity Δκ have also been estimated and analysed. Spectroscopic properties (IR, 1 H and 13 C NMR) of these mixtures have been investigated in order to understand the structural and interactional behaviour of formulations studied. The magnitude of interactions between the two components increases with addition of number of oxyethylene groups in Tritons and with rise in temperature. Spectroscopic measurements indicate that interactions are mainly taking place through the five member ring of room temperature ionic liquid and six member ring of Tritons.

  7. Influence of charged microenvironment on redox potential and ...

    Indian Academy of Sciences (India)

    Unknown

    triton X-100 (Sigma) are from Merck and used as received. The surfactants used are cetyltrimethyl- ammonium bromide (CTAB), triton X-100 (TX-100) and sodiumdodecyl sulphate (SDS). These are cationic, neutral and anionic respectively. Surfactant solutions used are 3% (w/v) surfactant in dimethyl formamide. (DMF).

  8. Triton Blushes: A Clue to Global Warming?

    Science.gov (United States)

    Buratti, B. J.; Hicks, M. D.; Newburn, R. L., Jr.

    1998-01-01

    The large Neptunian satellite Triton is a geologically active body that apparently undergoes complex seasonal changes in its 165 year journey around the sun. Because it is the vehicle for the seasonal transport of volatiles, Triton's atmosphere is expected to undergo large changes in temperature and pressure on a time scale of decades.

  9. Effect of surfactants on the morphology of FeSe films fabricated from ...

    Indian Academy of Sciences (India)

    ... solvent system and reactor type) except the use of three different concentrations of two different surfactants i.e., triton and span. Seven thin films were characterized with PXRD, SEM, AFM, EDS and EDS mapping. The mechanism of the interaction of surfactant with MeP2F was determined with cyclic voltammetry (CV) and ...

  10. Effects of Benzalkonium Chloride, Proxel LV, P3 Hypochloran, Triton X-100 and DOWFAX 63N10 on anaerobic digestion processes

    DEFF Research Database (Denmark)

    Flores, German Antonio Enriquez; Fotidis, Ioannis; Karakashev, Dimitar Borisov

    2015-01-01

    and continuous (up-flow anaerobic sludge blanket, UASB) reactors with biochemical-industrial wastewater, as substrate. In batch experiments, half-maximal inhibitory concentrations (IC50) for the tested xenobiotics were found to be 13.1, 1003, 311.5 and 24.3 mg L1 for BKC, PRX, DWF and TRX, respectively while HPC...

  11. UJI EFEK EKSTRAK ETANOL 96% ANGGUR MERAH (Vitis vinifera TERHADAP PENURUNAN KADAR TRIGLISERIDA PADA TIKUS PUTIH (Rattus Novergicus YANG DIINDUKSI TRITON X-100

    Directory of Open Access Journals (Sweden)

    Frans Saputra

    2017-01-01

    Full Text Available Buah anggur merah diduga memiliki kandungan pterostilbene, resveratrol, proantosianidin dan likopen yang memiliki efek terhadap penurunan kadar trigliserida. Penelitian ini bersifat eksperimental laboratorium dengan metode pre and post test with control group design. Objek penelitian 25 ekor tikus putih jantan, Rattus Novergicus, berat badan 150-200 gram, berumur 3-4 bulan yang dibagi menjadi 5 kelompok dengan teknik simple random sampling, kontrol negatif (aquadest, kontrol positif (Simvastatin 0,2mg/200gramBB/hari, kelompok perlakuan dosis I (100mg/200gramBB/hari, dosis II (250mg/200gramBB/hari, dosis III (500mg/200gramBB/ hari. Ekstrak etanol anggur merah dosis I, dosis II, dosis IIIdapat menurunkan kadar trigliserida darah dengan rerata penurunan secara berturut-turut adalah 147,4mg/dL, 135,2mg/dL, 97,2mg/dL. Pada uji statistic menggunakan one-way ANOVA didapatkan nilai p=0,000 (p<0,05, sehingga terdapat perbedaan signifikan kadar trigliserida darah tikus putih antar kelompok. Ekstrak etanol 96% anggur merah dosis 100mg; 250 dan 500 /200 gramBB/hari dapat menurunkan kadar trigliserida darah tikus putih.   Kata kunci :Ekstrak Anggur Merah, Trigliserida, Rattus Novergicus

  12. Numerical simulation of the SLAC X-100 klystron using RKTW2D

    International Nuclear Information System (INIS)

    Ryne, R.D.; Vlieks, A.E.

    1991-05-01

    We have performed numerical simulations of the X-100 klystron being developed at Stanford Linear Accelerator Center. The X-100 is being developed as a possible source for the next generation of linear collider, and will be required to produce ∼100 MW of power for a duration of ∼800 ns. Our simulations were performed using the simulation programs RKTW1D and RKTW2D, developed at Lawrence Livermore National Laboratory. The codes were used to investigate the operation of the klystron over a wide range of operating conditions. We will present comparisons of the simulation results with experimental results. 3 refs., 5 figs

  13. Role of surfactant derived intermediates in the efficacy and mechanism for radiation chemical degradation of a hydrophobic azo dye, 1-phenylazo-2-naphthol.

    Science.gov (United States)

    Das, Laboni; Chatterjee, Suchandra; Naik, Devidas B; Adhikari, Soumyakanti

    2015-11-15

    A combined methodology involving gamma and pulse radiolysis, product analysis and toxicity studies has been adopted to comprehend the degradation process of a model hydrophobic azo dye, 1-phenylazo-2-naphthol, emphasizing the role of the surfactant, which is an integral part of textile waste. Two new and important findings are underlined in this article. The first is the direct attestation of the hydrazyl radical-parent adduct, formed in the reaction of the dye with e(-)aq followed by protonation and subsequent addition to the unreacted dye molecule. This has been confirmed from concentration dependent studies. Secondly, we have clearly shown that in the reaction of hydroxyl radical with the dye in Triton X-100 media, the initially produced TX radicals cause reductive degradation of the dye. Identification and detailed analysis of HPLC and GCMS data reveals that similar products are formed in both the reactions of e(-)aq and OH radicals. Moreover, the cytotoxicity of 10(-4)moldm(-3) dye was found to be reduced significantly after irradiation. Thus, the present study not only depicts new pathways for the degradation of hydrophobic azo dye, but also demonstrates the role of a surfactant in the entire process. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. Did Triton Destroy Neptune's First Moons?

    Science.gov (United States)

    Kohler, Susanna

    2017-11-01

    Neptunes moon system is not what we would expect for a gas giant in our solar system. Scientists have now explored the possibility that Neptune started its life with an ordinary system of moons that was later destroyed by the capture of its current giant moon, Triton.An Odd SystemOur current understanding of giant-planet formation predicts a period of gas accretion to build up the large size of these planets. According to models, the circumplanetary gas disks that surround the planets during this time then become the birthplaces of the giant planets satellite systems, producing systems of co-planar and prograde (i.e., orbiting in the same direction as the planets rotation) satellites similar to the many-moon systems of Jupiter or Saturn.Tritons orbit is tilted relative to the inner Neptunian satellite orbits. [NASA, ESA, and A. Feild (STScI)]Neptune, however, is quirky. This gas giant has surprisingly few satellites only 14 compared to, say, the nearly 70 moons of Jupiter and most of them are extremely small. One of Neptunes moons is an exception to this, however: Triton, which contains 99.7% of the mass of Neptunes entire satellite system!Tritons orbit has a number of unusual properties. The orbit is retrograde Triton orbits in the opposite direction as Neptunes rotation which is unique behavior among large moons in our solar system. Tritons orbit is also highly inclined, and yet the moons path is nearly circular and lies very close to Neptune.The distribution of impact velocities in the authors simulations for primordial satellite interactions with Triton, in three cases of different satellite mass ratios. In the low-mass case a third of the mass ratio of the Uranian satellite system 88% of simulations ended with Triton surviving on its high-inclination orbit. The survival rate was only 12% in the high-mass case. [Adapted from Rufu et al. 2017]How did this monster of a satellite get its strange properties, and why is Neptunes system so odd compared to what we

  15. A Novel Aqueous Two Phase System Composed of Surfactant and Xylitol for the Purification of Lipase from Pumpkin (Cucurbita moschata) Seeds and Recycling of Phase Components.

    Science.gov (United States)

    Amid, Mehrnoush; Manap, Mohd Yazid; Hussin, Muhaini; Mustafa, Shuhaimi

    2015-06-17

    Lipase is one of the more important enzymes used in various industries such as the food, detergent, pharmaceutical, textile, and pulp and paper sectors. A novel aqueous two-phase system composed of surfactant and xylitol was employed for the first time to purify lipase from Cucurbita moschata. The influence of different parameters such as type and concentration of surfactants, and the composition of the surfactant/xylitol mixtures on the partitioning behavior and recovery of lipase was investigated. Moreover, the effect of system pH and crude load on the degree of purification and yield of the purified lipase were studied. The results indicated that the lipase was partitioned into the top surfactant rich phase while the impurities partitioned into the bottom xylitol-rich phase using an aqueous two phase system composed of 24% (w/w) Triton X-100 and 20% (w/w) xylitol, at 56.2% of tie line length (TLL), (TTL is one of the important parameters in this study and it is determined from a bimodal curve in which the tie-line connects two nodes on the bimodal, that represent concentration of phase components in the top and bottom phases) and a crude load of 25% (w/w) at pH 8.0. Recovery and recycling of components was also measured in each successive step process. The enzyme was successfully recovered by the proposed method with a high purification factor of 16.4 and yield of 97.4% while over 97% of the phase components were also recovered and recycled. This study demonstrated that the proposed novel aqueous two phase system method is more efficient and economical than the traditional aqueous two phase system method for the purification and recovery of the valuable enzyme lipase.

  16. A Novel Aqueous Two Phase System Composed of Surfactant and Xylitol for the Purification of Lipase from Pumpkin (Cucurbita moschata Seeds and Recycling of Phase Components

    Directory of Open Access Journals (Sweden)

    Mehrnoush Amid

    2015-06-01

    Full Text Available Lipase is one of the more important enzymes used in various industries such as the food, detergent, pharmaceutical, textile, and pulp and paper sectors. A novel aqueous two-phase system composed of surfactant and xylitol was employed for the first time to purify lipase from Cucurbita moschata. The influence of different parameters such as type and concentration of surfactants, and the composition of the surfactant/xylitol mixtures on the partitioning behavior and recovery of lipase was investigated. Moreover, the effect of system pH and crude load on the degree of purification and yield of the purified lipase were studied. The results indicated that the lipase was partitioned into the top surfactant rich phase while the impurities partitioned into the bottom xylitol-rich phase using an aqueous two phase system composed of 24% (w/w Triton X-100 and 20% (w/w xylitol, at 56.2% of tie line length (TLL, (TTL is one of the important parameters in this study and it is determined from a bimodal curve in which the tie-line connects two nodes on the bimodal, that represent concentration of phase components in the top and bottom phases and a crude load of 25% (w/w at pH 8.0. Recovery and recycling of components was also measured in each successive step process. The enzyme was successfully recovered by the proposed method with a high purification factor of 16.4 and yield of 97.4% while over 97% of the phase components were also recovered and recycled. This study demonstrated that the proposed novel aqueous two phase system method is more efficient and economical than the traditional aqueous two phase system method for the purification and recovery of the valuable enzyme lipase.

  17. Comparison of several ethanol productions using xylanase, inorganic salts, surfactant

    Science.gov (United States)

    Wu, Yan; Lu, Jie; Yang, Rui-feng; Song, Wen-jing; Li, Hai-ming; Wang, Hai-song; Zhou, Jing-hui

    2017-03-01

    Liquid hot water (LHW) pretreatment is an effective and environmentally friendly method to produce bioethanol with lignocellulosic materials. Corn stover was pretreated with liquid hot water (LHW) and then subjected to semi-simultaneous saccharification and fermentation (S-SSF) to obtain high ethanol concentration and yield. The present study aimed to confirm the effect of several additives on the fermentation digestibility of unwashed WIS of corn stover pretreated with LHW. So we also investigated the process, such as enzyme addition, inorganic salts, surfactant and different loading Triton. Results show that high ethanol concentration is necessary to add xylanase in the stage of saccharification. The ethanol concentration increased mainly with magnesium ion on fermentation. Comparing with Tween 80, Span 80 and Polyethylene glycol, Triton is the best surfactant. In contrast to using xylanase and Triton respectively, optimization can make up the lack of stamina and improve effect of single inorganic salts.

  18. From X100 to Vectorwise: opportunities, challenges and things most researchers do not think about

    NARCIS (Netherlands)

    M. Zukowski (Marcin); P.A. Boncz (Peter)

    2012-01-01

    textabstractIn 2008 a group of researchers behind the X100 database kernel created Vectorwise: a spin-o which together with the Actian corporation (previously Ingres) worked on bringing this technology to the market. Today, Vectorwise is a popular product and one of the examples of conversion of a

  19. Research and Development of Ultra-High Strength X100 Welded Pipe

    Science.gov (United States)

    Chuanguo, Zhang; Lei, Zheng; Ping, Hu; Bei, Zhang; Kougen, Wu; Weifeng, Huang

    Ultra-high strength X100 welded pipe can be used in the construction of long distance oil and gas pipeline to improve transmission capacity and reduce operation cost. By using the way of thermo-simulation and pilot rolling, the CCT (Continuous Cooling Transformation) diagram and the relationship between ACC (Accelerated Cooling) parameters, microstructure and mechanical properties were studied for the designed X100 pipeline steel with low carbon, high manganese and niobium micro-alloyed composition in lab. The analysis of CCT diagram indicates that the suitable hardness and microstructure can be obtained in the cooling rate of 20 80°C/sec. The pilot rolling results show that the ACC cooling start temperature below Ar3 phase transformation point is beneficial to increase uniform elongation, and the cooling stop temperature of 150 350°C is helpful to obtain high strength and toughness combination. Based on the research conclusions, the X100 plate and UOE pipe with dimension in O.D.1219×W.T.14.8mm, O.D.1219×W.T.17.8mm, designed for the natural gas transmission pipeline, were trial produced. The manufactured pipe body impact absorbed energy at -10°C is over 250J. The DWTT shear area ratio at 0°C is over 85%. The transverse strength meets the X100 grade requirement, and uniform elongation is over 4%. The X100 plate and UOE pipe with dimension in O.D.711×W.T.20.0mm, O.D.711×W.T.12.5mm, designed for an offshore engineering, were also trial produced. The average impact absorbed energy of pipe body at -30°C is over 200J. The average impact absorbed energy of HAZ (Heat-affected zone) and WM (Welded Seam) at -30°C is over 100J. And the good pipe shapes were obtained

  20. Investigation of electrokinetic and electrorheological properties of polyindole prepared in the presence of a surfactant

    Energy Technology Data Exchange (ETDEWEB)

    Unal, H. Ibrahim, E-mail: hiunal@gazi.edu.tr [Gazi University, Chemistry Department, Smart Materials Research Lab., Ankara (Turkey); Sahan, Bekir; Erol, Ozlem [Gazi University, Chemistry Department, Smart Materials Research Lab., Ankara (Turkey)

    2012-05-15

    Highlights: Black-Right-Pointing-Pointer Aggregated morphology was determined for PIN, spherical and porous hollows and everniae form morphologies were recorded for SPIN. Black-Right-Pointing-Pointer The PIN/SO and SPIN/SO systems showed almost similar electrokinetic attitudes and a typical shear thinning non-Newtonian viscoelastic behavior, vibration damping capability at elevated frequencies, and enhanced storage moduli with increasing temperature. Black-Right-Pointing-Pointer Non-linear recoverable viscoelastic manner was revealed from the creep-recovery experiments under external electric field. - Abstract: In this study, synthesis of polyindole (PIN) was carried out without and with the presence of a sodium dodecyl sulfate (SDS) surfactant (SPIN), using FeCl{sub 3} as an oxidizing agent. The synthesized materials were subjected to various characterizations techniques namely: particle size, magnetic susceptibility, elemental analysis, density, conductivity, dielectric constant, FTIR, {sup 1}H NMR, TGA, XRD, and SEM. Characterization results revealed the successful preparation of the homopolymers of PIN and SPIN. Zeta ({zeta})-potentials of the samples were measured in aqueous and non-aqueous (silicone oil, SO) media. Electrokinetic properties of PIN and SPIN in aqueous media were determined by {zeta}-potential measurements in the presence of various electrolytes (NaCl, BaCl{sub 2}, AlCl{sub 3}, Na{sub 2}SO{sub 4}) and surfactants (cetyltrimethyl ammonium bromide, SDS, and Triton X-100). Besides, the effect of pH onto {zeta}-potentials of the materials was also examined. The suspensions prepared in SO were subjected to external electric field strength and their electrorheological (ER) properties were investigated. Then the effects of shear rate, frequency, and temperature onto ER activities of the suspensions were examined. Further, creep and creep-recovery tests were applied to the PIN/SO and SPIN/SO suspension systems and reversible non-linear viscoelastic

  1. Synthesis and characterization of pharmaceutical surfactant templated mesoporous silica: Its application to controlled delivery of duloxetine

    Energy Technology Data Exchange (ETDEWEB)

    Mani, Ganesh; Pushparaj, Hemalatha; Peng, Mei Mei; Muthiahpillai, Palanichamy [Department of Chemical Engineering, Hanseo University, Seosan-si 356 706 (Korea, Republic of); Udhumansha, Ubaidulla [Department of Chemical Engineering, Hanseo University, Seosan-si 356 706 (Korea, Republic of); Department of Pharmaceutics, C.L. Baid Metha College of Pharmacy, Chennai (India); Jang, Hyun Tae, E-mail: htjang@hanseo.ac.kr [Department of Chemical Engineering, Hanseo University, Seosan-si 356 706 (Korea, Republic of)

    2014-03-01

    Graphical abstract: - Highlights: • Usefulness of dual pharmaceutical surfactants in silica synthesis was evaluated. • Effects of concentration of secondary template (Tween-40) were studied. • Effects of fixed solvothermal condition on mesostructure formation were studied. • Duloxetine drug loading capability was studied. • Sustained release of duloxetine was evaluated. - Abstract: A new group of mesoporous silica nanoparticles (MSNs) were synthesized using combination pharmaceutical surfactants, Triton X-100 and Tween-40 as template and loaded with duloxetine hydrochloride (DX), for improving the sustained release of DX and patterns with high drug loading. Agglomerated spherical silica MSNs were synthesized by sol–gel and solvothermal methods. The calcined and drug loaded MSNs were characterized using X-ray diffraction (XRD), Braunner–Emmett–Teller (BET), thermogravimetric analysis (TGA), Fourier-transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), diffuse reflectance ultraviolet–visible (DRS-UV–vis) spectroscopy. MSNs with high surface area and pore volume were selected and studied for their DX loading and release. The selected MSNs can accommodate a maximum of 34% DX within it. About 90% was released at 200 h and hence, the synthesized MSNs were capable of engulfing DX and sustain its release. Further form the Ritger and Peppas, Higuchi model for mechanism drug release from all the MSN matrices follows anomalous transport or Non-Fickian diffusion with the ‘r’ and ‘n’ value 0.9 and 0.45 < n < 1, respectively. So, from this study it could be concluded that the MSNs synthesized using pharmaceutical templates were better choice of reservoir for the controlled delivery of drug which requires sustained release.

  2. Atrazine and Diuron partitioning within a soil-water-surfactant system

    Science.gov (United States)

    Wang, P.; Keller, A.

    2006-12-01

    The interaction between pesticide and soil and water is even more complex in the presence of surfactants. In this study, batch equilibrium was employed to study the sorption of surfactants and the partitioning behaviors of Atrazine and Diuron within a soil-water-surfactant system. Five soils and four surfactants (nonionic Triton- 100, cationic Benzalkonium Chloride (BC), anionic Linear Alkylbenzenesulfonate (LAS), and anionic Sodium Dodecyl Sulfate (SDS)) were used. All surfactant sorption isotherms exhibited an initial linear increase at low surfactant concentrations but reached an asymptotic value as the surfactant concentrations increased. Among the surfactants, BC had the highest sorption onto all soils, followed by Triton-100 and then by LAS and SDS, implying that the nature of the charge significantly influences surfactant sorption. Sorption of either Triton-100 or BC was highly correlated with soil Cation Exchange Capacity (CEC) while that of LAS and SDS was complicated by the presence of Ca2+ and Mg2+ in the aqueous phase and the CEC sites. Both LAS and SDS formed complexes with Ca2+ and Mg2+, resulting in a significant decrease in the detergency of the surfactants. At high surfactant concentrations and with micelles present in the aqueous phase, the micelles formed a more competitive partitioning site for the pesticides, resulting in less pesticide sorbed to the soil. At low Triton-100 and BC concentration, the sorption of the surfactants first resulted in less Atrazine sorption but more Diuron sorption, implying competition between the surfactants and Atrazine, which serves as an indirect evidence that there is a different sorption mechanism for Atrazine. Atrazine is a weak base and it protonates and becomes positively charged near particle surfaces where the pH is much lower than in the bulk solution. The protonated Atrazine may then be held on the CEC sites via electrostatic attraction. Triton-100, LAS and SDS sorbed on the soil showed similar

  3. The Atmospheric Structure of Triton and Pluto

    Science.gov (United States)

    Elliot, James L.

    1998-01-01

    The goal of this research was to better determine the atmospheric structures of Triton and Pluto through further analysis of three occultation data sets obtained with the Kuiper Airborne Observatory (KAO.) As the research progressed, we concentrated our efforts on the Triton data, as this appeared to be the most fruitful. Three papers have been prepared as a result of this research. The first paper presents new results about Triton's atmospheric structure from the analysis of all ground-based stellar occultation data recorded to date, including one single-chord occultation recorded on 1993 July 10 and nine occultation lightcurves from the double-star event on 1995 August 14. These stellar occultation observations made both in the visible and in the infrared have good spatial coverage of Triton, including the first Triton central-flash observations, and are the first data to probe the altitude level 20-100 km on Triton. The small-planet lightcurve model of J. L. Elliot and L. A. Young was generalized to include stellar flux refracted by the far limb, and then fitted to the data. Values of the pressure, derived from separate immersion and emersion chords, show no significant trends with latitude, indicating that Triton's atmosphere is spherically symmetric at approximately 50 km altitude to within the error of the measurements; however, asymmetry observed in the central flash indicates the atmosphere is not homogenous at the lowest levels probed (approximately 20 km altitude). From the average of the 1995 occultation data, the equivalent isothermal temperature of the atmosphere is 47 plus or minus 1 K and the atmospheric pressure at 1400 km radius (approximately 50 km altitude) is 1.4 plus or minus 0.1 microbar. Both of these are not consistent with a model based on Voyager UVS and RSS observations in 1989. The atmospheric temperature from the occultation is 5 K colder than that predicted by the model and the observed pressure is a factor of 1.8 greater than the

  4. Enhanced Production and Characterization of a Solvent Stable Amylase from Solvent Tolerant Bacillus tequilensis RG-01: Thermostable and Surfactant Resistant

    Directory of Open Access Journals (Sweden)

    Soni Tiwari

    2014-01-01

    Full Text Available Ten bacterial strains isolated from the soil samples in the presence of cyclohexane were screened for amylase production. Among them, culture RG-01 was adjudged as the best amylase producer and was identified as Bacillus tequilensis from MTCC, Chandigarh. The isolate showed maximum amylase production (8100 U/mL in the presence of starch, peptone, and Ca2+ ions at 55°C pH 7.0 within 24 h of incubation. The enzyme was stable in the presence of n-dodecane, isooctane, n-decane, xylene, toluene, n-hexane, n-butanol, and cyclohexane, respectively. The presence of benzene, methanol, and ethanol marginally reduced the amylase stability, respectively. The enzyme was showed it 100% activity at 55°C and pH 7.0 with 119% and 127% stability at 55°C and pH 7.0, respectively. The enzyme was also stable in the presence of SDS, Tween-40, Tween-60, and Tween-80 (1% and was found stimulatory effect, respectively. Only Triton-X-100 showed a moderate inhibitory effect (5% on amylase activity. This isolate (Bacillus tequilensis RG-01 may be useful in several industrial applications owing to its thermotolerant and organic solvents and surfactants resistance characteristics.

  5. Enhanced production and characterization of a solvent stable amylase from solvent tolerant Bacillus tequilensis RG-01: thermostable and surfactant resistant.

    Science.gov (United States)

    Tiwari, Soni; Shukla, Neha; Mishra, Pooja; Gaur, Rajeeva

    2014-01-01

    Ten bacterial strains isolated from the soil samples in the presence of cyclohexane were screened for amylase production. Among them, culture RG-01 was adjudged as the best amylase producer and was identified as Bacillus tequilensis from MTCC, Chandigarh. The isolate showed maximum amylase production (8100 U/mL) in the presence of starch, peptone, and Ca(2+) ions at 55°C pH 7.0 within 24 h of incubation. The enzyme was stable in the presence of n-dodecane, isooctane, n-decane, xylene, toluene, n-hexane, n-butanol, and cyclohexane, respectively. The presence of benzene, methanol, and ethanol marginally reduced the amylase stability, respectively. The enzyme was showed it 100% activity at 55°C and pH 7.0 with 119% and 127% stability at 55°C and pH 7.0, respectively. The enzyme was also stable in the presence of SDS, Tween-40, Tween-60, and Tween-80 (1%) and was found stimulatory effect, respectively. Only Triton-X-100 showed a moderate inhibitory effect (5%) on amylase activity. This isolate (Bacillus tequilensis RG-01) may be useful in several industrial applications owing to its thermotolerant and organic solvents and surfactants resistance characteristics.

  6. Study on 3D surfactant assisted electrokinetic remediation of 1,2,4-trichlorobenzene in low permeability soil

    Science.gov (United States)

    Qiao, W.; Ye, S.; Wu, J.

    2014-12-01

    Electrickinetic(EK) is a promising remediation technology because of its capability to remediate soils with low permeability. It has been used for heavy metals and organic pollutant(OPs) contaminated soils. As the most OPs are poor solubility and strong sorption capacity, combined EK technology is usually used, for example, EK combined with surfactants. Numerous combined EK tests are done in one-dimension(1D) column, however, it is proved that there is a big gap between 1D tests and field application. The objectives of this study are to investigate the remediation efficiency and EK behavior of 1,2,4-trichlorobenzene(1,2,4-TCB) contaminated clay enhanced by surfactants in a three-dimension reactor with 28cm length×15cm width×16cm height. 1,2,4-TCB was one of the main contaminants at a field site in Nanjing, China, where the polluted soils are clay. Soil filled in EK cell was divided into six layers in depth, and each layer was divided into six parts in length and three parts in width. There were 108 specimens in total which realized 3D monitoring the effects of EK. Triton X-100(Exp1) and Tween80(Exp2) dissolved in NaCO3/NaHCO3 buffer respectively, were used as the anode purging solution. The distributions of soil pH and water content showed that the buffer was sufficient to neutralize H+ produced at anode and the direction of electroosmotic flow(EOF) remained constant. Exp2 generated a higher EOF than Exp1, but remediation efficiencies were not satisfactory so far. The concentration of 1,2,4-TCB in soil reached a peak and nadir in the normalized distances of 0.75 and 0.9 from cathode after 5 days, respectively. The 1,2,4-TCB concentration in the peak was almost twice as much as the initial concentration. It suggested that 1,2,4-TCB was desorbed from soil by surfactants and was transported from anode to cathode by EOF, which proved the capability of EK with surfactants to move 1,2,4-TCB in clay. The concentration of 1,2,4-TCB in the normalized distances of 0

  7. Diagnosis of spontaneous bacterial peritonitis: Role of tween 80 and triton X in ascitic fluid cultures

    Directory of Open Access Journals (Sweden)

    Iyer R

    2009-01-01

    Full Text Available A patient with alcoholic cirrhosis of the liver, portal hypertension with hepatic encephalopathy and spontaneous bacterial peritonitis (SBP was admitted in an obtunded condition. Attempts at delineating the aetiology of the SBP using conventional cultures as well as automated systems were not successful. The use of non-anionic surfactant agents such as Tween 80-incorporated blood agar and Triton X treatment of the specimens facilitated the growth of Klebsiella pneumoniae from the ascitic fluid, which otherwise would have been concluded to represent culture-negative neutrocytic ascites. Thus, the use of the aforementioned agents could be explored in elucidating the aetiology of body cavity infections when conventional methods fail.

  8. Tensiometric, fluorescence and 1H NMR study of mixed micellization of non-steroidal anti-inflammatory drug sodium salt of ibuprofen in the presence of non-ionic surfactant in aqueous/urea solutions

    International Nuclear Information System (INIS)

    Rub, Malik Abdul; Khan, Farah; Sheikh, Mohmad Shafi; Azum, Naved; Asiri, Abdullah M.

    2016-01-01

    Highlights: • Interaction between (IBF + TX-100) mixtures has been investigated. • (IBF + TX-100) mixtures exhibit synergistic behavior. • Urea increases the surface charge of the micelles resulting halt of the micelles formation. • N agg , K sv and dielectric constant of mixed systems have also been evaluated. • 1 H NMR data suggested that IBF and TX-100 interacts through hydrophobic as well as hydrophillic interaction. - Abstract: The desirable surface/bulk properties for specific applications of drug sodium salt of ibuprofen (IBF) and Triton X-100 (TX-100) can be achieved by adjusting mainly the composition of these systems. The interactions of anionic drug IBF with non-ionic surfactant TX-100 micelles have been investigated using tensiometry, fluorometry and 1 H NMR in aqueous as well in 250 mmol⋅kg −1 urea solutions. Different theoretical models like Clint, Rubingh, and Rosen, etc. were utilized to get information about the nature of interaction between these two in bulk and at the interface. These models disclose that the non-ideal behavior with attractive interaction in bulk and at the interface exists. The steady-state fluorescence quenching study was employed to evaluate micelle aggregation numbers (N agg ), which signify the involvement of surfactant was forever higher compared to IBF. Stern–Volmer binding constants (K sv ), micropolarity (I 1 /I 3 ) and dielectric constant (D exp ) of the mixtures are also obtained using fluorescence method. By the addition of urea raise in the surface charge of the micelles was observed followed by halt of the micellization of drug and surfactant as well as their mixture, therefore cmc values increases followed by decrease in aggregation number. The 1 H NMR resonance intensity variations were paralleled by upfield shifts in the resonance frequencies, due to an increased shielding of IBF happening from closeness of the non-ionic TX-100 surfactant.

  9. Role of surfactant derived intermediates in the efficacy and mechanism for radiation chemical degradation of a hydrophobic azo dye, 1-phenylazo-2-naphthol

    Energy Technology Data Exchange (ETDEWEB)

    Das, Laboni [Radiation & Photochemistry Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Chatterjee, Suchandra [Food Technology Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Naik, Devidas B. [Radiation & Photochemistry Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Adhikari, Soumyakanti, E-mail: asoumya@barc.gov.in [Radiation & Photochemistry Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

    2015-11-15

    Highlights: • Demonstration of the role of surfactant in the degradation of the hydrophobic dye. • First direct observation of the formation of “hydrazyl radical-parent” adduct. • Similar products obtained in the reaction of e{sup −}{sub aq} and ·OH radical in TX-100 medium. • Significant reduction in cytotoxicity of irradiated dye in aqueous–organic medium. • New mechanistic pathway could be delineated. - Abstract: A combined methodology involving gamma and pulse radiolysis, product analysis and toxicity studies has been adopted to comprehend the degradation process of a model hydrophobic azo dye, 1-phenylazo-2-naphthol, emphasizing the role of the surfactant, which is an integral part of textile waste. Two new and important findings are underlined in this article. The first is the direct attestation of the hydrazyl radical-parent adduct, formed in the reaction of the dye with e{sup −}{sub aq} followed by protonation and subsequent addition to the unreacted dye molecule. This has been confirmed from concentration dependent studies. Secondly, we have clearly shown that in the reaction of hydroxyl radical with the dye in Triton X-100 media, the initially produced TX radicals cause reductive degradation of the dye. Identification and detailed analysis of HPLC and GCMS data reveals that similar products are formed in both the reactions of e{sup −}{sub aq} and ·OH radicals. Moreover, the cytotoxicity of 10{sup −4} mol dm{sup −3} dye was found to be reduced significantly after irradiation. Thus, the present study not only depicts new pathways for the degradation of hydrophobic azo dye, but also demonstrates the role of a surfactant in the entire process.

  10. Erosion Behaviour of API X100 Pipeline Steel at Various Impact Angles and Particle Speeds

    Directory of Open Access Journals (Sweden)

    Paul C. Okonkwo

    2016-09-01

    Full Text Available Erosion is the gradual removal of material due to solid particle impingement and results in a failure of pipeline materials. In this study, a series of erosion tests were carried out to investigate the influence of particle speed and impact angle on the erosion mechanism of API X100 pipeline steel. A dry erosion machine was used as the test equipment, while the particle speed ranged from 20 to 80 m/s and impact angles of 30° and 90° were used as test parameters. The eroded API X100 steel surface was characterized using scanning electron microscope (SEM and X-ray photoelectron spectroscopy (XPS. The weight loss and erosion rate were also investigated. The results showed that at a 90° impact angle, a ploughing mechanism was occurring on the tested specimens, while material removal through low-angle cutting was the dominant mechanism at lower impact angles. Embedment of alumina particles on the target steel surface, micro-cutting, and low-angle cutting were observed at low impact angles. Therefore, the scratches, cuttings, and severe ploughings observed on some failed oil and gas pipelines could be attributed to the erosion mechanism.

  11. Evaluating the Passivation of Corrosion of API-X100 Steel with Cyclic Voltammetry

    Science.gov (United States)

    Eliyan, Faysal Fayez; Alfantazi, Akram

    2017-10-01

    In this research, cyclic voltammetry, in oxygen-free low bicarbonate-carbonate solutions, was used to study the corrosion reactions of a high-strength steel, API-X100. With cycles of different scan ranges, the effects of cycling, transpassivation, and cathodic reduction on the electrochemistry of the passive films were analyzed. It was found that carbonate in higher concentrations reduces the anodic activity and the cathodic reactions of the surface. Bicarbonate in small concentrations in solutions that contained low carbonate concentrations catalyzed dissolution and disrupted the formation of the passive films, in reference to the measured anodic currents. From the experiments, there was electrochemical evidence that with more cycles, the passive films were growing thicker, the transpassivation deteriorated the passive films, and during the cathodic reduction, the dissolution was occurring at lower potentials to facilitate later the passivation at higher potentials.

  12. Magnetic behavior of NixFe(100-x) (65=<x=<100) nanowire arrays

    International Nuclear Information System (INIS)

    Navas, D.; Asenjo, A.; Jaafar, M.; Pirota, K.R.; Hernandez-Velez, M.; Sanz, R.; Lee, W.; Nielsch, K.; Batallan, F.; Vazquez, M.

    2005-01-01

    Arrays of magnetic nanowires with composition Ni x Fe (100-x) (65= 2 and 105nm lattice parameter of hexagonal symmetry, is achieved by self-ordering process, and characterized by SEM and AFM. Magnetic behavior of the arrays has been determined by VSM. Maximum coercivity of around 1.23kOe and reduced remanence (about 0.8 saturation magnetization) is observed for x=77, while minimum values are observed for x=100. Detailed AFM and MFM studies allow us to gain additional information of the filling degree of pores which can result in a distributed nanowires length that finally correlates with a deterioration of macroscopic magnetic behavior of the array

  13. A simple and realistic triton wave function

    International Nuclear Information System (INIS)

    Lomnitz-Adler, J.; Pandharipande, V.R.

    1980-01-01

    We propose a simple triton wave function that consists of a product of three correlation operators operating on a three-body spin-isospin state. This wave function is formally similar to that used in the recent variational theories of nuclear matter, the main difference being in the long-range behavior of the correlation operators. Variational calculations are carried out with the Reid potential, using this wave function in the so-called 'symmetrized product' and 'independent pair' forms. The triton energy and density distributions obtained with the symmetrized product wave function agree with those obtained in Faddeev and other variational calculations using harmonic oscillator states. The proposed wave function and calculational methods can be easily generalized to treat the four-nucleon α-particle. (orig.)

  14. Triton - Stratospheric molecules and organic sediments

    Science.gov (United States)

    Thompson, W. Reid; Singh, Sushil K.; Khare, B. N.; Sagan, Carl

    1989-01-01

    Continuous-flow plasma discharge techniques show production rates of hydrocarbons and nitriles in N2 + CH4 atmospheres appropriate to the stratosphere of Titan, and indicate that a simple eddy diffusion model together with the observed electron flux quantitatively matches the Voyager IRIS observations for all the hydrocarbons, except for the simplest ones. Charged particle chemistry is very important in Triton's stratosphere. In the more CH4-rich case of Titan, many hydrocarbons and nitriles are produced in high yield. If N2 is present, the CH4 fraction is low, but hydrocarbons and nitriles are produced in fair yield, abundances of HCN and C2H2 in Triton's stratosphere exceed 10 to the 19th molecules/sq cm per sec, and NCCN, C3H4, and other species are predicted to be present. These molecules may be detected by IRIS if the stratosphere is as warm as expected. Both organic haze and condensed gases will provide a substantial UV and visible opacity in Triton's atmosphere.

  15. Effect of surfactants on the morphology of FeSe films fabricated from ...

    Indian Academy of Sciences (India)

    All the films were prepared via similar experimental conditions (temperature, flow rate, concentration, solvent system and reactor type) except the use of three different concentrations of two different surfactants i.e., triton and span. Seven thin films were characterized with PXRD, SEM, AFM, EDS and EDS mapping.

  16. Calculation of triton confinement and burn-up in tokamaks

    International Nuclear Information System (INIS)

    Anderson, D.; Battistoni, P.

    1987-01-01

    An analytical investigation is made of the confinement and subsequent burn-up of fusion produced tritons in a deuterium Tokamak plasma. Explicit approximations are obtained for the triton confinement factor, clearly displaying the scaling with physical parameters. The importance of pitch angle scattering losses during the triton slowing down is also estimated. A comparison with experiments and numerical calculations on the FT Tokamak slows good qualitative agreement. (authors)

  17. Effect of three representative surfactants on methane hydrate formation rate and induction time

    Directory of Open Access Journals (Sweden)

    Mostafa keshavarz Moraveji

    2017-06-01

    Full Text Available The effects of three types of surfactants on methane hydrate formation process were investigated. Three different classes of surfactants involving anionic (sodium dodecyl sulfonate, cationic (hexadecyl trimethyl ammonium bromide and non-ionic (poly oxy ethylene (40 octyl phenyl ether have been used. Thermodynamics of hydrate formation, formation rate, kinetic constants and induction time in the presence of surfactants with various concentrations were analyzed. Critical micelle concentrations (CMCs of these surfactants in water were determined by induction time measurements in various concentrations under methane hydrate formation conditions. The critical micelle concentration (CMC at the methane hydrate formation conditions for SDS, HTABr and TritonX-405 solutions were obtained at 450, 380 and 950 ppm, respectively. The experimental results indicated that hydrate formation rate increased with the use of surfactants for all concentrations and induction time decreased. It was found that for surfactants, CMC at hydrate formation conditions was less than CMC at ambient conditions.

  18. Deposition and release kinetics of nano-TiO2 in saturated porous media: Effects of solution ionic strength and surfactants

    International Nuclear Information System (INIS)

    Godinez, Itzel G.; Darnault, Christophe J.G.; Khodadoust, Amid P.; Bogdan, Dorin

    2013-01-01

    The aggregation, transport and deposition kinetics (i.e. attachment and release) of TiO 2 nanoparticles (nano-TiO 2 ) were investigated as a function of ionic strength and the presence of anionic (sodium dodecylbenzene sulfonate, SDBS) and non-ionic (Triton X-100) surfactants in 100% critical micelle concentration (CMC). The electrolyte concentration of the suspensions dictated the kinetic stability of nano-TiO 2 thus influencing the transport and retention of the nanoaggregates in the saturated porous medium. With increasing ionic strength, the interaction between approaching nano-TiO 2 and nano-TiO 2 already deposited onto collectors surfaces seemed to be more favorable than the interaction between approaching nano-TiO 2 and bare collectors surfaces. The abrupt and gradual reduction in electrolyte concentration during the flushing cycles of the column experiments induced the release of previously deposited nano-TiO 2 suggesting attachment of nano-TiO 2 through secondary energy minimum. Highlights: ► This study focuses on aggregation, transport and deposition kinetics of nano-TiO 2 . ► Ionic strength and surfactants impact nano-TiO 2 transport in saturated porous media. ► Previously deposited nano-TiO 2 serve as preferential sites for subsequent deposition. ► Changes in solution chemistry cause nanodeposits to release a portion of nano-TiO 2 . -- Previously deposited nano-TiO 2 serve as preferential sites for subsequent deposition and changes in solution chemistry cause nanodeposits to release a portion of nano-TiO 2

  19. Malignant Triton Tumor (MTT) of the neck

    DEFF Research Database (Denmark)

    Sørensen, Kristine Bjørndal; Godballe, Christian; Krogdahl, Annelise

    2006-01-01

    Malignant Triton Tumor (MTT) is a rare, malignant periphere nerve sheath tumor with rhabdomyoblastic differentiation. One third of described MTT's were located at the head and neck region. One third of these are associated with neurofibromatosis type 1. MTT most often appears in the third decade....... MTT's are very aggressive tumors with early metastases and the overall survival is poor (26%). Therefore, early diagnosis and correct treatment is of utmost importance. We report a case of MTT of the left supraclavicular region in a 41-year-old man. We present the pathological findings, both light...

  20. Characterization of alkaline lipase from Fusarium oxysporum and the effect of different surfactants and detergents on the enzyme activity Caracterização de lipase alcalina de Fusarium oxysporum e o efeito de diferentes surfactantes e detergentes sobre a atividade enzimática

    Directory of Open Access Journals (Sweden)

    Janaina Nicanuzia dos Prazeres

    2006-12-01

    Full Text Available Nowadays, there is a tendency of use of low temperature in laundry cleaning for both environmental and economical reasons, which makes the use of enzymes in detergent products indispensable. Since lipases are efficient catalyst both in solution and at the water-liquid interface, they are potentially suitable for lipid stain removal applications in industrial laundry and household detergents. The effect of different commercial detergents and surfactants on enzymatic activity of lipase from Fusarium oxysporum was observed through p-nitrophenylpalmitate (pNPP assay. The enzyme was compatible with various ionic and non-ionic surfactants as well as commercial detergents. Lipase activity was strongly inhibited by Sodium Dodecyl Sulphate (SDS, but not by Triton X-100 and Triton X-114. The best assay conditions observed for this lipase were pH 8.0 and 50ºC. The enzyme was stable at alkaline pH and remained 93% of residual activity during 1 h incubation at 60ºC. The highest lipase activity was measured with triglycerides of middle and long chain fatty acids (C8-C18. This enzyme showed a variable specifity/hydrolytic activity towards various fats and oils. All these properties and its resistance towards various surfactants and tolerance to commercial detergents make this lipase a potential additive for detergent formulation.Atualmente, há uma tendência de utilizar baixas temperaturas em limpeza de lavanderia por razões ambientais e econômicas, situações estas que tornam indispensáveis o uso de enzimas em produtos detergentes. Devido às lipases serem excelentes catalisadoras em soluções e em interface água-óleo, elas são potencialmente apropriadas para aplicação na remoção de manchas de gorduras em lavanderia industrial e detergentes domésticos. O efeito de diferentes detergentes comerciais e surfactantes sobre a atividade enzimática da lipase de Fusarium oxysporum foi observado através de ensaios com p-nitrofenilpalmitato (pNPP. A

  1. Colloid and surfactant

    International Nuclear Information System (INIS)

    Kuk, Yun Hwan; Lee, Jeong Jung; Cho, Sun Chae; Ryeo, Su Dong

    1995-08-01

    This book consists of two parts about colloid and surfactant. The first parts has explanations colloid and surface science, which deal with creation and properties of colloidal particles, surfactant and micelle colloid, property of surfactant, membranes, absorption of surface science, electrokinetic phenomenon, emulsion, foam and rheology. The second part mentions surfactant on anionic surfactant with five types, amphoteric surface active agent, non-ionic surface active agent and use of surfactant.

  2. Study on the Toughness of X100 Pipeline Steel Heat Affected Zone

    Science.gov (United States)

    Li, Xueda; Shang, Chengjia; Ma, Xiaoping; Subramanian, S. V.

    Microstructure-property correlation of heat affected zone (HAZ) in X100 longitudinal submerged arc welding (LSAW) real weld joint was studied in this paper. Coarse grained (CG) HAZ and intercritically reheated coarse grained (ICCG) HAZ were characterized by optical microscope (OM), electron backscattered diffraction (EBSD). The microstructure of CGHAZ is mostly composed of granular bainite with low density of high angle boundaries (HAB). Prior austenite grain size is 80μm. In ICCGHAZ, coarse prior austenite grains were decorated by coarse necklacing martensite-austenite (M-A) constituents. Different layers were observed within M-A constituent, which may be martensite and austenite layers. Charpy absorbed energy of two different HAZ regions (ICCGHAZ containing and non-containing regions) was recorded using instrumental Charpy impact test machine. The results showed that the existence of ICCGHAZ resulted in the sharp drop of Charpy absorbed energy from 180J to 50J, while the existence of only CGHAZ could still lead to good toughness. The fracture surface was 60% brittle in the absence of ICCGHAZ, and 100% brittle in the presence of ICCGHAZ in the impact tested samples. The underlying reason is the microstructure of ICCGHAZ consisted of granular bainite and upper bainite with necklace-type M-A constituent along the grain boundaries. Cleavage fracture initiated from M-A constituent, either through cracking of M-A or debonding from the matrix, was observed at the fracture surface of ICCGHAZ. The presence of necklace type M-A constituent in ICCGHAZ notably increases the susceptibility of cleavage microcrack nucleation. Furthermore, the study of secondary microcracks beneath the CGHAZ and the ICCGHAZ through EBSD suggested that the fracture mechanism changes from nucleation-controlled in the CGHAZ to propagation-controlled in the ICCGHAZ because of the presence of necklace-type M-A constituent in the ICCGHAZ region. Both fracture mechanism contribute to the poor

  3. Lead preconcentration in synthetic samples with triton x-114 in the cloud point extraction and analysis by atomic absorption (EAAF)

    International Nuclear Information System (INIS)

    Zegarra Pisconti, Marixa; Cjuno Huanca, Jesus

    2015-01-01

    A methodology was developed about lead preconcentration in water samples that were added dithizone as complexing agent, previously dissolved in the nonionic surfactant Triton X-114, until the formation of the critical micelle concentration and the cloud point temperature. The centrifuged system gave a precipitate with high concentrations of Pb (II) that was measured by atomic absorption spectroscopy with flame (EAAF). The method has proved feasible to be implemented as a method of preconcentration and analysis of Pb in aqueous samples with concentrations less than 1 ppm. Several parameters were evaluated to obtain a percentage recovery of 89.8%. (author)

  4. Interpretation and significance of reverse chevron-shaped markings on fracture surfaces of API X100 pipeline steels

    International Nuclear Information System (INIS)

    Sowards, Jeffrey W.; McCowan, Chris N.; Drexler, Elizabeth S.

    2012-01-01

    Highlights: ► We investigated fractures of X100 steel linepine produced during fracture mechanics testing. ► Fractures exhibited a unique chevron pattern that points in the direction of crack propagation. ► A qualitative model is proposed to explain the fracture pattern formation. ► Findings indicate that careful interpretation of ductile material fractures is necessary. - Abstract: Fracture surfaces of X100 pipeline steels were examined with optical and electron microscopy after crack tip opening angle fracture testing. Some fracture surfaces exhibited chevron-shaped fracture patterns that are markedly different from classic chevron fracture. The chevron-shaped markings on the X100 fracture surfaces point in the direction of crack growth, rather than towards the location of fracture initiation, as observed in classic cases of chevron fracture. Existing models, predicting formation of chevron fracture patterns, do not explain the fracture behavior observed for X100 steel. A mechanism is proposed where reverse chevron-shaped patterns are developed due to the shape of the crack front itself. The chevron shape forms as a result of crack tunneling, and the overall pattern is developed on the fracture surface due to intermittent crack growth, resulting in alternating regions (bands) of fast fracture and slower, more ductile fracture. The contrast between these bands of alternating fracture defines the chevron. Care should be taken during interpretation of intermittent chevron markings on fractures of ductile materials, as they may point away from rather than towards the origin of fracture.

  5. [Exogenous surfactant therapy: new synthetic surfactants].

    Science.gov (United States)

    Lacaze-Masmonteil, Th

    2008-06-01

    There are numerous pulmonary conditions in which qualitative or quantitative anomalies of the surfactant system have been demonstrated. In premature newborns with immature lungs, a functional deficit in surfactant is the main physiopathologic mechanism of the neonatal respiratory distress syndrome (RDS). Since the landmark pilot study of Fujiwara, published more than 20 years ago, the efficacy of exogenous surfactant for the treatment of neonatal RDS has been established by numerous controlled studies and meta-analyses. Enlightened by a growing insight into both the structure and function of the different surfactant components, a new generation of synthetic surfactants has been developed. Various complementary approaches have confirmed the fundamental role of the two hydrophobic proteins, SP-B and SP-C, in the surfactant system, thus opening the way to the design of analogues, either by chemical synthesis or expression in a prokaryotic system. An example of these peptide-containing synthetic surfactant preparations, lucinactant (Surfaxin), has been recently tested in comparison to a synthetic surfactant that does not contain protein as well as to animal derived surfactant preparations. Major clinical outcomes between lucinactant and animal-derived surfactant preparations were fund similar in two randomized controlled trials, opening the way to a new generation of synthetic surfactants in the near future.

  6. Escaping 1 MeV tritons in TFTR

    International Nuclear Information System (INIS)

    Zweben, S.J.; Strachan, J.D.; Boivin, R.; Cavallo, A.; Fredrickson, E.D.; McGuire, K.; Mynick, H.E.; White, R.B.

    1989-01-01

    1 MeV tritons created by D-D reactions can simulate the 'single-particle' behavior expected with 3.5 MeV D-T alphas, since the gyroradii and slowing-down of these two particles are similar. This paper describes measurements of the flux of escaping 1 MeV tritons from the TFTR plasma during high power D 0 →D neutral beam injection, and shows that in most cases the observed triton loss is consistent with the classical (single-particle) first-orbit loss model. In this model tritons are lost if their first orbit intersects the wall due to their large banana width, while almost all tritons confined on their first orbit should stay confined until thermalized. The triton detectors are ZnS(Ag) scintillator screens housed in light-tight boxes located just outside the plasma boundary at the bottom of the TFTR vessel. They are particle 'pinhole' cameras which can resolve the triton flux vs. pitch angle (to ±5 o ), energy (to ±50 %), and time (to <20 μsec). The 2-D images of triton flux onto these scintillators are optically coupled to either an intensified TV camera or to photomultiplyer tubes for fast time resolution. The soft x-ray background in an earlier prototype has been eliminated. Although there are presently 8 such detectors in TFTR, this paper discusses results from only the detector located just below the vessel center (R=259 cm, r=102 cm). Note that the '1 MeV triton' signal discussed below also has about a 30 % contribution from 3 MeV protons; however, since these two particles have identical gyroradii they should behave alike. 5 refs., 5 figs

  7. Evidence for the di-triton resonance in 6He

    International Nuclear Information System (INIS)

    Akimune, H.; Yamagata, T.; Nakayama, S.

    2002-01-01

    A di-triton cluster state at highly excited energies in 6 He has been investigated via the ( 7 Li, 7 Be) reaction with an incident energy of 65 MeV/A. Decay charged-particles from excited states in 6 He were measured in coincidence with 7 Be ejectiles using solid-state detectors. A prominent bump was observed at E x =18 MeV in the binary triton decay channel. The branching ratio of the binary triton decay channel from this bump was 100% based on the spectrum decomposition analysis. (author)

  8. Flow Behaviour of Alkali, Surfactant, and Xanthan Solutions Used for Enhanced Oil Recovery Fluidité des solutions d'alcali, de tensio-actif et de xanthane utilisées pour la récupération assistée du pétrole

    Directory of Open Access Journals (Sweden)

    Nasr-El-Din H. A.

    2006-11-01

    Full Text Available An experimental study was conducted to examine the effects of various alkalis, surfactants and brines on the viscosity of dilute aqueous solutions of two xanthan materials containing medium and high pyruvate content, over a wide range of parameters. The effect of alkalis on the flow curves of xanthan solutions depended on alkali type and concentration, shear rate and pyruvate content of xanthan. Strong alkalis caused partial degradation of the xanthan molecules. As a result, a fast and significant reduction in apparent viscosity occurred, especially with the high pyruvate xanthan. This drop was only noticeable at low shear rates. Buffered alkalis were less detrimental to the viscosity of xanthan solutions. Triton X-100 up to 10 wt% had no significant effect on the flow curves of both xanthan materials. Neodol 25-3S caused noticeable changes only in the flow curves of the high pyruvate xanthan. Triton X-100 up to 10 wt% in the presence of alkali had no significant effect on the flow curves of either xanthan material. The addition of anionic surfactants at low concentrations slightly decreased the viscosity of alkali/xanthan solutions. A significant viscosity enhancement was observed at higher surfactant concentrations over a narrow range of alkali concentrations. This behaviour was only observed with anionic surfactants and was due to the formation of surfactant aggregates. The effect of sodium chloride on the apparent viscosity of xanthan solutions depended on polymer concentration and the pyruvate content of xanthan. Only the high pyruvate polymer at high polymer concentrations (= 1 wtO/o showed a dramatic increase in the apparent viscosity upon the addition of sodium chloride. At low polymer concentrations, calcium chloride had a more detrimental effect on the viscosity of the high pyruvate xanthan than sodium chloride. Une étude expérimentale a été effectuée pour examiner les effets de divers alcalis, tensioactifs et saumures sur la

  9. Deuteron-, triton - and alpha - clusters in nuclear matter

    International Nuclear Information System (INIS)

    Bando, H.; Coelho, H.T.; Delfino, A.

    1981-01-01

    It is studied with a simple model how deuteron-, triton- and α-clusters behave concerning their cluster structure identities during the scatterring process and just after reaching nuclear matter of finite size. (Author) [pt

  10. Triton Hopper: Exploring Neptune's Captured Kuiper Belt Object

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose a hopper vehicle using a radioisotope thermal rocket engine, using in-situ propellant, to explore Neptune's moon Triton. This moon is thought to be a...

  11. Voyager IRIS Measurements of Triton's Thermal Emission: Impllications for Pluto?

    Science.gov (United States)

    Stansberry, John A.; Spencer, John; Linscott, Ivan

    2015-11-01

    The New Horizons Pluto encounter data set includes unique observations obtained using the Radio Science experiment to measure the night-side thermal emission at centimeter wavelengths, well beyond the emission peak (in the 70 to 100 micron range). 26 years ago the Voyager 2 Infrared Interferometer Spectrometer (IRIS) obtained spectra in the 30 - 50 micron wavelength range to try and detect thermal emission from Pluto's sibling, Triton. Conrath etal. (1989) analyzed 16 of the IRIS spectra of Triton's dayside and derived a weak limit of 36 K - 41 K. We have analysed those, and an additional 75 spectra, to refine the limits on the temperature of Triton's surface, and to explore diurnal differences in the thermal emission. Triton results from other Voyager instruments provide important constraints on our interpretation of the IRIS data, as do Spitzer measurements of Pluto's thermal emission.For unit-emissivity, average temperature is 34 K, inconsistent with the pressure of Triton's atmosphere (13 - 19 microbar), the presence of beta-phase nitrogen ice on the surface, and the likely presence ofwarm regions on the surface. The atmospheric pressure requires nitrogen ice temperatures of 37.4 K - 38.1 K, which in turn requires emissivity of 0.31--0.53. Such a low emissivity in this spectral region might be expected if the surface is dominated by nitrogen or methane ice. Averages of data subsets show evidence for brightness temperature variations across Triton's surface. Surprisingly, the data seem to indicate that Triton's nightside equatorial region was warmer than on the dayside.These Voyager results for Triton provide a useful context for interpreting New Horizons and ALMA observations of emission from Pluto in the sub-millimeter and centimeter region. JWST will be capable of detecting Triton's and Pluto's 10 - 28 micron thermal emission, although scattered light from Neptune may be an issue for the Triton. Combined with new capabilities of ALMA to measure the sub

  12. Thermally cleavable surfactants

    Science.gov (United States)

    McElhanon, James R [Manteca, CA; Simmons, Blake A [San Francisco, CA; Zifer, Thomas [Manteca, CA; Jamison, Gregory M [Albuquerque, NM; Loy, Douglas A [Albuquerque, NM; Rahimian, Kamyar [Albuquerque, NM; Long, Timothy M [Urbana, IL; Wheeler, David R [Albuquerque, NM; Staiger, Chad L [Albuquerque, NM

    2006-04-04

    Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments and the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

  13. Thermally cleavable surfactants

    Science.gov (United States)

    McElhanon, James R [Manteca, CA; Simmons, Blake A [San Francisco, CA; Zifer, Thomas [Manteca, CA; Jamison, Gregory M [Albuquerque, NM; Loy, Douglas A [Albuquerque, NM; Rahimian, Kamyar [Albuquerque, NM; Long, Timothy M [Urbana, IL; Wheeler, David R [Albuquerque, NM; Staiger, Chad L [Albuquerque, NM

    2009-11-24

    Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

  14. Studies of Triton X-165-beta-cyclodextrin interactions using both extrinsic and intrinsic fluorescence.

    Science.gov (United States)

    Mahata, Atanu; Bose, Debosreeta; Ghosh, Debanjana; Jana, Barnali; Bhattacharya, Bhaswati; Sarkar, Deboleena; Chattopadhyay, Nitin

    2010-07-15

    The interaction of beta-cyclodextrin with the non-ionic micelle-forming surfactant Triton X-165 (TX-165) has been studied using steady state fluorescence and fluorescence anisotropy techniques. Both extrinsic and intrinsic fluorescence have been exploited for the purpose. Phenosafranin (PSF), a cationic phenazinium dye, has been used as the extrinsic probe while fluorescence of TX-165 has served as the intrinsic one. PSF shows discernible interactions with both TX-165 and beta-CD. The experimental results reveal that the extent of interaction of PSF with TX-165 is greater than with beta-CD. However, addition of beta-CD to a micellar solution of TX-165 containing PSF leads to a disruption of the micelles whereby the fluorophore is released from the micellar environment to the bulk aqueous phase. It has been substantiated that an inclusion complex is formed between the non-ionic surfactant and the cyclodextrin. A 1:1 stoichiometry of the TX-165-beta-CD inclusion complex has been proposed. Such a complexation between TX-165 and beta-CD results in an inhibition in the micellization process of TX-165 leading to an enhancement in the apparent CMC value. The inferences are drawn from a series of experiments, viz., binding studies, determination of micropolarity, heavy-ion quenching studies and steady state fluorescence anisotropy experiments monitoring both extrinsic and intrinsic fluorescences. Copyright 2010 Elsevier Inc. All rights reserved.

  15. sodium dodecyl sulphate (SDS)

    Indian Academy of Sciences (India)

    Unknown

    sodium dodecyl sulphate, SDS) showed a marked effect, although there are some reports where cationic (cetyl trimethyl ammonium bromide, CTAB) and neutral (Triton X-100) surfactants have also shown changes in the. *For correspondence ...

  16. Gemini (dimeric) Surfactants

    Indian Academy of Sciences (India)

    Gemini, surfactants, micelle. Figure 1. Schematic repre- sentation of the gemini sur- factant structure. B S Sekhon. A gemini surfactant (GS) consists of two conventional surfactant molecules chemically bonded together by a spacer. The two terminal hydrocarbon tails can be short or long; the two polar head groups can be ...

  17. Corrosion behavior and characteristics of the product film of API X100 steel in acidic simulated soil solution

    Science.gov (United States)

    Du, Cui-wei; Zhao, Tian-liang; Liu, Zhi-yong; Li, Xiao-gang; Zhang, Da-wei

    2016-02-01

    The short-term corrosion behavior of API X100 steel in an acidic simulated soil was investigated by electrochemical measurements and soaking experiments, followed by corrosion morphology observations and X-ray photoelectron spectroscopy analyses. The results show that X100 steel exhibits an obvious pitting susceptibility in an acidic soil environment. Pits nucleate after approximately 10 h of immersion. Along with the nucleation and growth of the pits, the charge-transfer resistance and open-circuit potential first increase sharply, then decrease slowly, and eventually reach a steady state. The maxima of the charge-transfer resistance and open-circuit potential are attained at approximately 10 h. The evolution of the electrochemical process is confirmed by the analysis of the product film. The product film exhibits a porous and loose structure and could not protect the substrate well. The product film is primarily composed of ferrous carbonate and ferrous hydroxide (Fe(OH)2). The concentration of Fe(OH)2 in the product film increases from the inside to the outside layer.

  18. Enhanced photocatalytic degradation of norfloxacin in aqueous Bi{sub 2}WO{sub 6} dispersions containing nonionic surfactant under visible light irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Lin, E-mail: tanglin@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Wang, Jiajia [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Zeng, Guangming, E-mail: zgming@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Liu, Yani; Deng, Yaocheng; Zhou, Yaoyu; Tang, Jing; Wang, Jingjing; Guo, Zhi [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China)

    2016-04-05

    Highlights: • TX100 strongly enhanced the adsorption and photodegradation of NOF in Bi{sub 2}WO{sub 6} dispersions under visible light irradiation (400–750 nm). • Cu{sup 2+} (10 mM) significantly suppressed the photocatalytic degradation of NOF. • FT-IR demonstrated that the NOF adsorbed on Bi{sub 2}WO{sub 6} was completely degraded. • Three possible photocatalytic degradation pathways of NOF were proposed, according to the HPLC/MS/MS analysis. - Abstract: Photocatalytic degradation is an alternative method to remove pharmaceutical compounds in water, however it is hard to achieve efficient rate because of the poor solubility of pharmaceutical compounds in water. This study investigated the photodegradation of norfloxacin in a nonionic surfactant Triton-X100 (TX100)/Bi{sub 2}WO{sub 6} dispersion under visible light irradiation (400–750 nm). It was found that the degradation of poorly soluble NOF can be strongly enhanced with the addition of TX100. TX100 was adsorbed strongly on Bi{sub 2}WO{sub 6} surface and accelerated NOF photodegradation at the critical micelle concentration (CMC = 0.25 mM). Higher TX100 concentration (>0.25 mM) lowered the degradation rate. In the presence of TX100, the degradation rate reached the maximum value when the pH value was 8.06. FTIR analyses demonstrated that the adsorbed NOF on the catalyst was completely degraded after 2 h irradiation. According to the intermediates identified by HPLC/MS/MS, three possible degradation pathways were proposed to include addition of hydroxyl radical to quinolone ring, elimination of piperazynilic ring in fluoroquinolone molecules, and replacement of F atoms on the aromatic ring by hydroxyl radicals.

  19. Pluto and Triton: Interactions Between Volatiles and Dynamics

    Science.gov (United States)

    Rubincam, D. P.

    2001-01-01

    Volatiles moving across the surfaces of Pluto and Triton can give rise to interesting dynamical consequences. Conversely, measurement of dynamical states can help constrain the movement of volatiles and interior structure of both bodies. Polar wander may theoretically occur on both Triton and Pluto. Triton's obliquity is low, so that the equatorial regions receive more insolation than the poles. Hence there is a tendency for nitrogen ice to sublime at the equator and condense at the poles, creating polar caps. If the nitrogen supply is large enough, then these caps could move in approximately 10(exp 5) years the global equivalent of 200 m of ice to the poles. At this point the equatorial moment of inertia becomes larger than the moment of inertia measured about the rotation axis, so that Triton overbalances and becomes dynamically unstable. The satellite then undergoes polar wander, restoring stability when the new equator contains the excess matter. Hence the pole may be continually wandering. Neptune raises a permanent tidal bulge on Triton, so that the satellite's surface is elongated like a football, with the long axis pointing at Neptune. This is expected to be the axis about which the pole wanders. Volatile migration would resurface the satellite to some depth and wandering would disturb leading side/trailing side crater statistics. Additional information is contained in the original extended abstract.

  20. Complementary experimental-simulational study of surfactant micellar phase in the extraction process of metallic ions: Effects of temperature and salt concentration

    Science.gov (United States)

    Soto-Ángeles, Alan Gustavo; Rodríguez-Hidalgo, María del Rosario; Soto-Figueroa, César; Vicente, Luis

    2018-02-01

    The thermoresponsive micellar phase behaviour that exhibits the Triton-X-100 micelles by temperature effect and addition of salt in the extraction process of metallic ions was explored from mesoscopic and experimental points. In the theoretical study, we analyse the formation of Triton-X-100 micelles, load and stabilization of dithizone molecules and metallic ions extraction inside the micellar core at room temperature; finally, a thermal analysis is presented. In the experimental study, the spectrophotometric outcomes confirm the solubility of the copper-dithizone complex in the micellar core, as well as the extraction of metallic ions of aqueous environment via a cloud-point at 332.2 K. The micellar solutions with salt present a low absorbance value compared with the micellar solutions without salt. The decrease in the absorbance value is attributed to a change in the size of hydrophobic region of colloidal micelles. All transitory stages of extraction process are discussed and analysed in this document.

  1. Triton burnup measurements in KSTAR using a neutron activation system

    Science.gov (United States)

    Jo, Jungmin; Cheon, MunSeong; Kim, Jun Young; Rhee, T.; Kim, Junghee; Shi, Yue-Jiang; Isobe, M.; Ogawa, K.; Chung, Kyoung-Jae; Hwang, Y. S.

    2016-11-01

    Measurements of the time-integrated triton burnup for deuterium plasma in Korea Superconducting Tokamak Advanced Research (KSTAR) have been performed following the simultaneous detection of the d-d and d-t neutrons. The d-d neutrons were measured using a 3He proportional counter, fission chamber, and activated indium sample, whereas the d-t neutrons were detected using activated silicon and copper samples. The triton burnup ratio from KSTAR discharges is found to be in the range 0.01%-0.50% depending on the plasma conditions. The measured burnup ratio is compared with the prompt loss fraction of tritons calculated with the Lorentz orbit code and the classical slowing-down time. The burnup ratio is found to increase as plasma current and classical slowing-down time increase.

  2. A thermal model for the seasonal nitrogen cycle on Triton

    Science.gov (United States)

    Hansen, Candice J.; Paige, David A.

    1992-01-01

    The seasonal N2-cycle model presently used to characterize such observed phenomena on Triton as atmospheric pressure and surface albedo features at the time of the Voyager encounter incorporates diurnal and seasonal subsurface heat conduction, and can account for the heat capacity of N2 frost deposits. The results obtained by this model differ from those of previous studies in that they do not predict the seasonal freezing-out of the Triton atmosphere; even for a wide range of input parameters, the bright southern polar cap is seen as rather unlikely to be N2. The results support the microphysical arguments for the presence of either dark or smooth translucent N2 frosts on the Triton surface.

  3. Replanteamiento de la Estrategia 100x100 a partir de un Índice de Desarrollo Humano para Localidades

    Directory of Open Access Journals (Sweden)

    Francisco José Zamudio-Sánchez

    2016-01-01

    Full Text Available En este artículo se presenta un índice para medir el desarrollo humano. Se toman como bases conceptuales los principios de Amartya Sen y, como forma operativa, una métrica estadística. Comparamos los resultados de un conjunto de municipios con el índice propuesto, contra los municipios incluidos en la denominada Estrategia 100x100. La selección indica que la estrategia debe ser modificada y que el índice propuesto se relaciona mejor con otros índices sociales actualmente usados. Nuestra metodología es muy general para construir un índice y puede ser usada para obtener medidas de otras características sociales.

  4. Surfactants in tribology

    CERN Document Server

    Biresaw, Girma

    2014-01-01

    Surface science and tribology play very critical roles in many industries. Manufacture and use of almost all consumer and industrial products rely on the application of advanced surface and tribological knowledge. The fourth in a series, Surfactants in Tribology, Volume 4 provides an update on research and development activities connecting surfactants and tribological phenomena. Written by renowned subject matter experts, the book demonstrates how improved design of surfactants can be harnessed to control tribological phenomena. Profusely illustrated and copiously referenced, the chapters also

  5. Genetics Home Reference: surfactant dysfunction

    Science.gov (United States)

    ... Email Facebook Twitter Home Health Conditions Surfactant dysfunction Surfactant dysfunction Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Surfactant dysfunction is a lung disorder that causes breathing ...

  6. Structure-Property-Fracture Mechanism Correlation in Heat-Affected Zone of X100 Ferrite-Bainite Pipeline Steel

    Science.gov (United States)

    Li, Xueda; Ma, Xiaoping; Subramanian, S. V.; Misra, R. D. K.; Shang, Chengjia

    2015-03-01

    Structural performance of a weld joint primarily depends on the microstructural characteristics of heat-affected zone (HAZ). In this regard, the HAZ in X100 ferrite-bainite pipeline steel was studied by separating the HAZ into intercritically reheated coarse-grained (ICCG) HAZ containing and non-containing regions. These two regions were individually evaluated for Charpy impact toughness and characterized by electron back-scattered diffraction (EBSD). Low toughness of ~50 J was obtained when the notch of impact specimen encountered ICCGHAZ and high toughness of ~180 J when the notch did not contain ICCGHAZ. Fracture surface was ~60 pct brittle in the absence of ICCGHAZ, and 95 pct brittle (excluding shear lip) in the presence of ICCGHAZ in the impact tested samples. The underlying reason is the microstructure of ICCGHAZ consisted of granular bainite and upper bainite with necklace-type martensite-austenite (M-A) constituent along grain boundaries. The presence of necklace-type M-A constituent notably increases the susceptibility of cleavage microcrack nucleation. ICCGHAZ was found to be both the initiation site of the whole fracture and cleavage facet initiation site during brittle fracture propagation stage. Furthermore, the study of secondary microcracks beneath CGHAZ and ICCGHAZ through EBSD suggested that the fracture mechanism changes from nucleation-controlled in CGHAZ to propagation-controlled in ICCGHAZ because of the presence of necklace-type M-A constituent in ICCGHAZ. Both fracture mechanisms contribute to the poor toughness of the sample contained ICCGHAZ.

  7. Fundamentals of surfactant sputtering

    International Nuclear Information System (INIS)

    Hofsaess, Hans; Zhang Kun

    2009-01-01

    We introduce a new sputter technique, utilizing the steady-state coverage of a substrate surface with up to 10 16 cm -2 of foreign atoms simultaneously during sputter erosion by combined ion irradiation and atom deposition. These atoms strongly modify the substrate sputter yield on atomic to macroscopic length scales and therefore act as surfactant atoms (a blend of 'surface active agent'). Depending on the surfactant-substrate combination, the novel technique allows enhanced surface smoothing, generation of novel surface patterns, shaping of surfaces and formation of ultra-thin films. Sputter yield attenuation is demonstrated for sputtering of Si and Fe substrates and different surfactant species using 5 keV Xe ions at different incidence angles and fluences up to 10 17 cm -2 . Analytical approaches and Monte Carlo simulations are used to predict the sputtering yield attenuation as function of surfactant coverage. For sputtering of Si with Au surfactants we observe high sputter yields despite a steady-state surfactant coverage, which can be explained by strong ion-induced interdiffusion of substrate and surfactant atoms and the formation of a buried Au x Si surfactant layer in dynamic equilibrium.

  8. Dynamic covalent surfactants

    NARCIS (Netherlands)

    Minkenberg, C.B.

    2012-01-01

    In this thesis the development of surfactant aggregates with fast exchange dynamics between the aggregated and non-aggregated state is described. Dynamic surfactant exchange plays an important role in natural systems, for instance in cell signaling, cell division, and uptake and release of cargo.

  9. Pulmonary surfactant and lung transplantation

    NARCIS (Netherlands)

    Erasmus, Michiel Elardus

    1997-01-01

    Pulmonary surfactant lowers the surface tension at the air-water interface inside the alveolus. This is achieved by adsorption of surfactant phospholipids at the air-water interface, a process controlled by surfactant-associated proteins, such as SP-A. In this way, surfactant prevents collapse of

  10. A study of triton radiative capture in some light nuclei

    International Nuclear Information System (INIS)

    Schaeffer, Michel.

    1975-01-01

    The aim of this work is to complete the knowledge of the nucleon Giant Dipole Resonance (G.D.R.) by means of the study of radiative capture of complex particles: tritons. The following reactions were studied: 12 C(t,γ 0 ) 15 N, 16 O(t,γ) 19 F, 20 Ne(t,γ) 23 Na, 24 Mg(t,γ 0 ) 27 Al, 24 Mg(t,γ 1 ) 27 Al*, 23 Na(t,γ 0 ) 26 Mg, 23 Na(t,γ) 26 Mg* between between 1.5 and 3.5MeV incident triton energy. The detector was a 25x30cm NaI(Tl) crystal [fr

  11. Simulation of triton burn-up in JET plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Loughlin, M.J.; Balet, B.; Jarvis, O.N.; Stubberfield, P.M. [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking

    1994-07-01

    This paper presents the first triton burn-up calculations for JET plasmas using the transport code TRANSP. Four hot ion H-mode deuterium plasmas are studied. For these discharges, the 2.5 MeV emission rises rapidly and then collapses abruptly. This phenomenon is not fully understood but in each case the collapse phase is associated with a large impurity influx known as the ``carbon bloom``. The peak 14 MeV emission occurs at this time, somewhat later than that of the 2.5 MeV neutron peak. The present results give a clear indication that there are no significant departures from classical slowing down and spatial diffusion for tritons in JET plasmas. (authors). 7 refs., 3 figs., 1 tab.

  12. Surfactants in the environment.

    Science.gov (United States)

    Ivanković, Tomislav; Hrenović, Jasna

    2010-03-01

    Surfactants are a diverse group of chemicals that are best known for their wide use in detergents and other cleaning products. After use, residual surfactants are discharged into sewage systems or directly into surface waters, and most of them end up dispersed in different environmental compartments such as soil, water or sediment. The toxic effects of surfactants on various aquatic organisms are well known. In general, surfactants are present in the environment at levels below toxicity and in Croatia below the national limit. Most surfactants are readily biodegradable and their amount is greatly reduced with secondary treatment in wastewater treatment plants. The highest concern is the release of untreated wastewater or wastewater that has undergone primary treatment alone. The discharge of wastewater polluted with massive quantities of surfactants could have serious effects on the ecosystem. Future studies of surfactant toxicities and biodegradation are necessary to withdraw highly toxic and non-biodegradable compounds from commercial use and replace them with more environmentally friendly ones.

  13. Characterization of impregnated GDC nano structures and their functionality in LSM based cathodes

    DEFF Research Database (Denmark)

    Klemensø, Trine; Chatzichristodoulou, Christodoulos; Nielsen, Jimmi

    2012-01-01

    Porous composite cathodes of LSM–YSZ (lanthanum strontium manganite and yttria stabilized zirconia) were impregnated with GDC (gadolinia doped ceria) nano particles. The impregnation process was varied using none or different surfactants (Triton X-45, Triton X-100, P123), and the quantity...

  14. Structure of Triton's atmosphere from the occultation of Tr176

    Science.gov (United States)

    Sicardy, B.; Mousis, O.; Beisker, W.; Hummel, E.; Hubbard, W. B.; Hill, R.; Reitsema, H. J.; Anderson, P.; Ball, L.; Downs, B.; Hutcheon, S.; Moy, M.; Nielsen, G.; Pink, I.; Walters, R.

    1998-09-01

    The occultation of the star Tr176 by Triton (Mc Donald & Elliot, AJ 109, 1352, 1995) was observed on 18 July 1997 from three stations in Queensland, Australia (Bundaberg, Ducabrook and Lochington) and one station in Texas, USA (Brownsville). All observations were made with CCD (no filter) and with portable C14 telescopes, except at Bundaberg, where a fixed 48-cm telescope was used. Time sampling rate ranges from 0.33 sec (Bundaberg) to 0.66 sec (Ducabrook and Lochington), with the intermediate value 0.5 sec at Brownsville. Isothermal fits were performed to the lightcurves in order to determine the isothermal temperature, T_iso, and the radius at half-level, R_{1/2}, of Triton's atmosphere (assumed to be composed of pure N_2). Considering the level of noise, we cannot detect any departure from isothermal profiles, and we do not see any deviations from spherical shape. A global fit yields T_iso = 53.7 +/- 2 K and R_{1/2} = 1456 +/- 3 km. We also derive the pressure at 1400 km: p1400 = 1.9 +/- 0.3 mu bars. We will discuss these results and compare them with previous works obtained by Voyager teams from the 1989 observations, and by Olkin et al. (Icarus 129, 178, 1997), who analyze two Triton occultations observed in July 1993 (Tr60) and August 1995 (Tr148). We observe a general increase of pressure at 1400 km, since Olkin et al. derive p1400 = 1.4 +/- 0.1 mu bars from the Tr148 event. This result is actually confirmed by a recent work by Elliot et al., (Nature 393, 765 1998), who note a global warming on Triton, based in particular on a new HST occultation observation in November 1997 (Tr180).

  15. Stabilizing two IgG1 monoclonal antibodies by surfactants: Balance between aggregation prevention and structure perturbation.

    Science.gov (United States)

    Wang, Shujing; Wu, Guoliang; Zhang, Xinyi; Tian, Zhou; Zhang, Ning; Hu, Tao; Dai, Weiguo; Qian, Feng

    2017-05-01

    Surfactants are widely used as stabilizers in the biopharmaceutical formulations to minimize protein aggregation. Under a fixed stress condition, the protecting and destabilizing effects of surfactants are hypothesized to be highly dependent on the species and concentrations of surfactants and mAb. Therefore, we here studied the aggregation-prevention and structure-perturbation effects of eight commonly used surfactants (Tw20, Tw80, Brij35, Chaps, TrX-100, SDS, Pluronic F68 and F127) on two IgG1 solution formulations under agitation, using analytical methodologies including visual inspection, OD 350 measurement, HPLC-SEC, circular dicroism, fluorescence spectroscopy and differential scanning calorimetry. We found that: (1) With concentrations range from 0.02 to 2mg/mL, nonionic surfactants were found to offer efficient aggregation-prevention effect, which is superior than the ionic surfactants; and higher surfactant concentration prevented mAb aggregation better especially under prolonged stability test under stress conditions. (2) The surfactant induced structure-perturbation emerged when even higher surfactant concentration (≥2mg/mL) was used, and such effect was surfactant-property dependent; and (3) the two IgG1 demonstrated different aggregation mechanisms and surfactant dependency, especially at high mAb concentrations. In conclusion, surfactants usage in mAb formulations, including the types and concentrations, should strike an optimal balance between the desirable aggregation-prevention and the detrimental structure-perturbation effects, while the consideration of mAb aggregation mechanism and concentration is also required for surfactant assessment. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Metathesis depolymerizable surfactants

    Science.gov (United States)

    Jamison, Gregory M [Albuquerque, NM; Wheeler, David R [Albuquerque, NM; Loy, Douglas A [Tucson, AZ; Simmons, Blake A [San Francisco, CA; Long, Timothy M [Evanston, IL; McElhanon, James R [Manteca, CA; Rahimian, Kamyar [Albuquerque, NM; Staiger, Chad L [Albuquerque, NM

    2008-04-15

    A class of surfactant molecules whose structure includes regularly spaced unsaturation in the tail group and thus, can be readily decomposed by ring-closing metathesis, and particularly by the action of a transition metal catalyst, to form small molecule products. These small molecules are designed to have increased volatility and/or enhanced solubility as compared to the original surfactant molecule and are thus easily removed by solvent extraction or vacuum extraction at low temperature. By producing easily removable decomposition products, the surfactant molecules become particularly desirable as template structures for preparing meso- and microstructural materials with tailored properties.

  17. Neptune's Triton: A moon rich in dry ice and carbon

    Science.gov (United States)

    Prentice, A. J. R.

    1989-01-01

    The encounter of the spacecraft Voyager 2 with Neptune and its large satellite Triton in August 1989 will provide a crucial test of ideas regarding the origin and chemical composition of the outer solar system. In this pre-encounter publication, the possibility is quantified that Titron is a captured moon which, like Pluto and Charon, originally condensed as a major planetesimal within the gas ring that was shed by the contracting protosolar cloud at Neptune's orbit. Ideas of supersonic convective turbulence are used to compute the gas pressure, temperature and rat of catalytic synthesis of CH4, CO2, and C(s) within the protosolar cloud, assuming that all C is initially present as CO. The calculations lead to a unique composition for Triton, Pluto, Charon: each body consists of, by mass, 18 1/2 percent solid CO2 ice, 4 percent graphite, 1/2 percent CH4 ice, 29 percent methanated water ice and 48 percent of anhydrous rock. This mix has a density consistent with that of the Pluto-Charon system and yields a predicted mean density for Triton of 2.20 + or - 0.5 g/cu cm, for satellite radius equal to 1,750 km.

  18. Psychoanalytic and musical ambiguity: the tritone in gee, officer krupke.

    Science.gov (United States)

    Jaffee Nagel, Julie

    2010-02-01

    The poignant and timeless Broadway musical West Side Story is viewed from the standpoint of taking musical forms as psychoanalytic data. The musical configuration of notes called the tritone (or diabolus in musica) is taken as a sonic metaphor expressing ambiguity both in musical vocabulary and in mental life. The tritone, which historically and harmonically represents instability, is heard throughout the score and emphasizes the intrapsychic, interpersonal, and social dramas that unfold within and between the two gangs in West Side Story. Particular emphasis is given to the comic but exceedingly sober song Gee, Officer Krupke. Bernstein's sensitivity to the ambiguity and tension inherent in the tritone in West Side Story is conceptualized as an intersection of music theory and theories of mind; this perspective holds implications for clinical practice and transports psychoanalytic concepts from the couch to the Broadway stage and into the community to address the complexities of love, hate, aggression, prejudice, and violence. Ultimately, West Side Story cross-pollinates music and theater, as well as music and psychoanalytic concepts.

  19. Pitch jnd and the tritone paradox: The linguistic nexus

    Science.gov (United States)

    Safari, Kourosh

    2002-11-01

    Previous research has shown a connection between absolute pitch (the ability to name a specific pitch in the absence of any reference) and native competence in a tone language (Deutsch, 1990). In tone languages, tone is one of the features which determines the lexical meaning of a word. This study investigates the relationship between native competence in a tone language and the just noticeable difference of pitch. Furthermore, the tritone paradox studies have shown that subjects hear two tritones (with bell-shaped spectral envelopes) as either ascending or descending depending on their linguistic backgrounds (Deutsch, 1987). It is hypothesized that the native speakers of tone languages have a higher JND for pitch, and hear the two tones of the tritone paradox as ascending, whereas, native speakers of nontone languages hear them as descending. This study will indicate the importance of early musical training for the development of acute tone sensitivity. It will also underline the importance of language and culture in the way it shapes our musical understanding. The significance of this study will be in the areas of music education and pedagogy.

  20. Comparative calculations and parametric studies using HELIOS and TRITON. Technical report; Vergleichsrechnungen und Parameterstudien mit HELIOS und TRITON. Technischer Bericht

    Energy Technology Data Exchange (ETDEWEB)

    Sommer, Fabian

    2017-05-15

    In the frame of the project ''evaluation and feasibility of a validation for computational codes for criticality and burnout calculations for the use in systems with boiling water reactor fuel'' the burnout code HELIOS for the calculation of inventories was used which allows due to the fast routines Monte-Carlo based sensitivity and uncertainty analyses. The calculated neutron multiplication factor for the HELIOS based calculations were compared with TRITON results.

  1. Surfactive stabilization of multi-walled carbon nanotube dispersions with dissolved humic substances

    Energy Technology Data Exchange (ETDEWEB)

    Chappell, Mark A. [Environmental Laboratory, Engineering Research and Development Center, US Army Corps of Engineers, 3909 Halls Ferry Road, Vicksburg, MS 39180 (United States)], E-mail: mark.a.chappell@usace.army.mil; George, Aaron J.; Dontsova, Katerina M.; Porter, Beth E. [SpecPro, Inc., 4815 Bradford Drive, Suite 201, Huntsville, AL 35805 (United States); Price, Cynthia L. [Environmental Laboratory, Engineering Research and Development Center, US Army Corps of Engineers, 3909 Halls Ferry Road, Vicksburg, MS 39180 (United States); Zhou Pingheng; Morikawa, Eizi [J. Bennett Johnston Sr. Center for Advanced Microstructures and Devices, Louisiana State University, 6980 Jefferson Highway, Baton Rouge, LA 70806 (United States); Kennedy, Alan J.; Steevens, Jeffery A. [Environmental Laboratory, Engineering Research and Development Center, US Army Corps of Engineers, 3909 Halls Ferry Road, Vicksburg, MS 39180 (United States)

    2009-04-15

    Soil humic substances (HS) stabilize carbon nanotube (CNT) dispersions, a mechanism we hypothesized arose from the surfactive nature of HS. Experiments dispersing multi-walled CNT in solutions of dissolved Aldrich humic acid (HA) or water-extractable Catlin soil HS demonstrated enhanced stability at 150 and 300 mg L{sup -1} added Aldrich HA and Catlin HS, respectively, corresponding with decreased CNT mean particle diameter (MPD) and polydispersivity (PD) of 250 nm and 0.3 for Aldrich HA and 450 nm and 0.35 for Catlin HS. Analogous trends in MPD and PD were observed with addition of the surfactants Brij 35, Triton X-405, and SDS, corresponding to surfactant sorption maximum. NEXAFS characterization showed that Aldrich HA contained highly surfactive domains while Catlin soil possessed a mostly carbohydrate-based structure. This work demonstrates that the chemical structure of humic materials in natural waters is directly linked to their surfactive ability to disperse CNT released into the environment. - Suspensions of multi-walled carbon nanotubes are stabilized by relatively low concentrations of dissolved humic substances in solution through surfactive mechanisms.

  2. Phosphine oxide surfactants revisited.

    Science.gov (United States)

    Stubenrauch, Cosima; Preisig, Natalie; Laughlin, Robert G

    2016-04-01

    This review summarizes everything we currently know about the nonionic surfactants alkyl dimethyl (C(n)DMPO) and alkyl diethyl (C(n)DEPO) phosphine oxide (PO surfactants). The review starts with the synthesis and the general properties (Section 2) of these compounds and continues with their interfacial properties (Section 3) such as surface tension, surface rheology, interfacial tension and adsorption at solid surfaces. We discuss studies on thin liquid films and foams stabilized by PO surfactants (Section 4) as well as studies on their self-assembly into lyotropic liquid crystals and microemulsions, respectively (Section 5). We aim at encouraging colleagues from both academia and industry to take on board PO surfactants whenever possible and feasible because of their broad variety of excellent properties. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Neuroprotection of Grape Seed Extract and Pyridoxine against Triton-Induced Neurotoxicity

    Directory of Open Access Journals (Sweden)

    Heba M. Abdou

    2016-01-01

    Full Text Available Triton WR-1339 administration causes neurotoxicity. Natural products and herbal extracts can attenuate cerebral injury. In the present study, we investigated the neuroprotective role of grape seed extract and/or vitamin B6 against triton-induced neurotoxicity. Thirty-five adult male albino rats of the Sprague-Dawley strain, weighing 140–145 g, were divided into five groups: control, triton, grape seed extract + triton, grape seed extract + triton + vitamin B6, and vitamin B6 + triton. The hematological and biochemical analyses were carried out. Alteration in iNOS mRNA gene expression was determined using reverse-transcriptase PCR analysis. In addition, qualitative DNA fragmentation was examined using agarose gel electrophoresis. Triton-treatment caused significant disturbances in the hematological parameters, the neurological functions, and the antioxidant profile. Also, triton significantly increased the iNOS mRNA expression and DNA damage. Our results showed that grape seed extract and/or vitamin B6 could attenuate all the examined parameters. These natural substances could exhibit protective effects against triton-induced neurological damage because of their antioxidative and antiapoptotic capacities.

  4. TRITON: graphic software for rational engineering of enzymes.

    Science.gov (United States)

    Damboský, J; Prokop, M; Koca, J

    2001-01-01

    Engineering of the catalytic properties of enzymes requires knowledge about amino acid residues interacting with the transition state of the substrate. TRITON is a graphic software package for modelling enzymatic reactions for the analysis of essential interactions between the enzyme and its substrate and for in silico construction of protein mutants. The reactions are modelled using semi-empirical quantum-mechanic methods and the protein mutants are constructed by homology modelling. The users are guided through the calculation and data analysis by wizards.

  5. A new cartography for the Triton and Nereide reactors

    International Nuclear Information System (INIS)

    Debiar, A.; Loverini, M.J.; Annibal, M.

    1997-01-01

    Triton and Nereide are two reactors from the first generation of pool type reactors, and have been dismantled between 1982 and 1986; they are to be used as a test and certification station for dismantling materials. Since 1993, they are continuously monitored. In 1983, a first reactivity balance was carried out, showing an equivalent residual activity inferior to 1.3 curie, which was followed by the classification of the facilities and its thorough cleaning. A new cartography of the radiological state of the site is in course, before its final decommissioning

  6. Investigation of fusion proton and triton emission in ASDEX

    International Nuclear Information System (INIS)

    Leinberger, U.

    1991-01-01

    A diagnostic method of measuring the fusion rate profile was developed on ASDEX. The collimated protons and tritons from d-d fusion reaction are simultaneously detected by a semiconductor counter at a single position in the vacuum vessel for different viewing directions. The detection efficiency profiles for these viewing directions are numerically calculated from the measured currents in the coils and assumed plasma current distributions. Folding the detection efficiency profile with a fusion rate profile yields the proton and triton fluxes to the detector. Comparison with measured fluxes allows one to find a fusion rate profile in agreement with the experimental data. In certain cases the detection efficiency profile strongly on the plasma current density profile, and information on the current distribution in the plasma can thus be achieved. It was proved that the spectra from rotating plasmas are in accordance with the theory of a rotating thermal plasma. Deviations can only be found in the case of strong vignetting of the detection efficiency by structures in the vacuum vessel. (orig.)

  7. Charge-exchange reactions with a secondary triton beam

    CERN Document Server

    Sherrill, B M; Austin, S M; Bazin, D; Berg, A; Berg, G P A; Caggiano, J; Daito, I; Fujimura, H; Fujita, Y; Fujiwara, M; Hara, K; Harakeh, M N; Jänecke, J; Kawabata, T; Navin, A; Roberts, D A; Steiner, M

    1999-01-01

    A secondary triton beam from fragmentation of 560-MeV alpha-particles has been used in a high-resolution (t, sup 3 He) charge-exchange experiment at intermediate bombarding energies. The experiment was carried out at the National Superconducting Cyclotron Laboratory using a sup 4 He beam from the K1200 cyclotron. The radioactive triton beam of (0.5-1.0)x10 sup 6 particles/s with a mean energy of 350 MeV was produced in a production target of the A1200 fragment separator and transported to the target position of the S800 magnetic spectrometer. Ray-tracing and dispersion-matching techniques were employed to detect sup 3 He particles from the sup 1 sup 2 C(t, sup 3 He) sup 1 sup 2 B reaction near 0 deg. . An energy resolution of DELTA E approx 160 keV or DELTA E/E approx 4.6x10 sup - sup 4 (FWHM) was achieved. This is an improvement over our previous results and opens the possibility for studying high-resolution (n,p)-type reactions at intermediate bombarding energies. (author)

  8. Diseases of Pulmonary Surfactant Homeostasis

    Science.gov (United States)

    Whitsett, Jeffrey A.; Wert, Susan E.; Weaver, Timothy E.

    2015-01-01

    Advances in physiology and biochemistry have provided fundamental insights into the role of pulmonary surfactant in the pathogenesis and treatment of preterm infants with respiratory distress syndrome. Identification of the surfactant proteins, lipid transporters, and transcriptional networks regulating their expression has provided the tools and insights needed to discern the molecular and cellular processes regulating the production and function of pulmonary surfactant prior to and after birth. Mutations in genes regulating surfactant homeostasis have been associated with severe lung disease in neonates and older infants. Biophysical and transgenic mouse models have provided insight into the mechanisms underlying surfactant protein and alveolar homeostasis. These studies have provided the framework for understanding the structure and function of pulmonary surfactant, which has informed understanding of the pathogenesis of diverse pulmonary disorders previously considered idiopathic. This review considers the pulmonary surfactant system and the genetic causes of acute and chronic lung disease caused by disruption of alveolar homeostasis. PMID:25621661

  9. Coacervation with surfactants: From single-chain surfactants to gemini surfactants.

    Science.gov (United States)

    Zhao, Weiwei; Wang, Yilin

    2017-01-01

    Coacervation is a spontaneous process during which a colloidal dispersion separates into two immiscible liquid phases: a colloid-rich liquid phase in equilibrium with a diluted phase. Coacervation is usually divided into simple coacervation and complex coacervation according to the number of components. Surfactant-based coacervation normally contains traditional single-chain surfactants. With the development of surfactants, gemini surfactants with two amphiphilic moieties have been applied to form coacervation. This review summarizes the development of simple coacervation and complex coacervation in the systems of single-chain surfactants and gemini surfactants. Simple coacervation in surfactant solutions with additives or at elevated temperature and complex coacervation in surfactant/polymer mixtures by changing charge densities, molecular weight, ionic strength, pH, or temperature are reviewed. The comparison between gemini surfactants and corresponding monomeric single-chain surfactants reveals that the unique structures of gemini surfactants endow them with higher propensity to generate coacervation. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. The Sendai triton calculation with three-nucleon potentials

    International Nuclear Information System (INIS)

    Sasakawa, T.

    1986-01-01

    Where can we see the effects of quarks remains a fundamental question in nuclear theory physics. A bold approach is to try to reproduce physical quantities theoretically by utilizing a quark picture with imagination. A conservative but safer approach may be to study the triton as thoroughly as possible using realistic two- and three-nucleon potentials. We are taking the latter approach. In fact, our calculation of the EMC effect, which was one thought to be a realization of the quark-gluon picture of nuclei, suggests that we might not have to make recourse to this picture. The calculation was done for 3 He, while experimental data for 4 He are shown. We hope that an experiment for 3 He is done soon, to check whether our conservative approach actually works for the EMC effect. (orig./WL)

  11. Particle-size dependent sorption and desorption of pesticides within a water-soil-nonionic surfactant system.

    Science.gov (United States)

    Wang, Peng; Keller, Arturo A

    2008-05-01

    Although nonionic surfactants have been considered in surfactant-aided soil washing systems, there is little information on the particle-size dependence of these processes, and this may have significant implications for the design of these systems. In this study, Triton-100 (TX) was selected to study its effect on the sorption and desorption of two pesticides (Atrazine and Diuron) from different primary soil size fractions (clay, silt, and sand fractions) under equilibrium sorption and sequential desorption. Soil properties, TX sorption, and pesticide sorption and desorption all exhibited significant particle-size dependence. The cation exchange capacity (CEC) of the bulk soils and the soil fractions determined TX sorption capacity, which in turn determined the desorption efficiency. Desorption of pesticide out of the clay raction is the limiting factor in a surfactant-aided washing system. The solubilization efficiency of the individual surfactant micelles decreased as the amount of surfactant added to the systems increased. Thus, instead of attempting to wash the bulk soil, a better strategy might be to either (1) use only the amount of surfactant that is sufficient to clean the coarse fraction, then separate the fine fraction, and dispose or treat it separately, or (2) to separate the coarse fractions mechanically and then treatthe coarse and fine fractions separately. These results may be applicable to many other hydrophobic organic compounds such as polyaromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) strongly sorbed onto soils and sediments.

  12. Ex situ characterization of metallurgical inclusions in X100 pipeline steel before and after immersion in a neutral pH bicarbonate solution

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yingbo; Liu, Jie [Key Laboratory of Advanced Ceramics and Machining Technology (Ministry of Education), School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Deng, Yida [Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin 300072 (China); Han, Xiaopeng [Key Laboratory of Advanced Ceramics and Machining Technology (Ministry of Education), School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Hu, Wenbin [Key Laboratory of Advanced Ceramics and Machining Technology (Ministry of Education), School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin 300072 (China); Zhong, Cheng, E-mail: cheng.zhong@tju.edu.cn [Key Laboratory of Advanced Ceramics and Machining Technology (Ministry of Education), School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China)

    2016-07-15

    The initiation of corrosion pits in pipeline steels plays an important role in the development of stress corrosion cracking. In order to reveal the effect of inclusions on corrosion initiation sites and also to clarify contradictory results from previous literature, we proposed an ex situ characterization method that is allowed to characterize exactly the same inclusion or location of the surface of steel before and after corrosion tests. The time-dependent corrosion behaviour of the inclusions and the surrounding X100 steel matrix at the same area before and after early stage immersion in a near-neutral pH bicarbonate solution was investigated by ex situ scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) analysis and localized electrochemical impedance spectroscopy (LEIS). The sizes of most inclusions in X100 steel are below 3 μm. The results challenge the long-held opinion of previous work that corrosion pit initiations are related with the inclusions. It has been found that most of the inclusions remain stable (intact) during the whole testing time although severe corrosion occurs on the matrix of the steel. The chemical composition of the inclusion greatly affects the chemical stability of the inclusion. SiO{sub 2} inclusions and complex inclusions with a high SiO{sub 2} content remain intact although obvious general corrosion occurs on the steel matrix under the investigated immersion period. Inclusions with little Si, such as Al–Mg–Ca–O enriched inclusions, totally disappear after certain immersion time. During the immersion, the corrosion product tends to deposit at the interstice between the inclusion and steel matrix. - Highlights: • Ex situ characterization of metallurgical inclusions in X100 pipeline steel. • The pipeline steel was immersed in neutral pH bicarbonate solution. • Majority of inclusions remain stable during the whole testing time. • The chemical stability of metallurgical inclusions depends on the SiO{sub 2

  13. Ex situ characterization of metallurgical inclusions in X100 pipeline steel before and after immersion in a neutral pH bicarbonate solution

    International Nuclear Information System (INIS)

    Li, Yingbo; Liu, Jie; Deng, Yida; Han, Xiaopeng; Hu, Wenbin; Zhong, Cheng

    2016-01-01

    The initiation of corrosion pits in pipeline steels plays an important role in the development of stress corrosion cracking. In order to reveal the effect of inclusions on corrosion initiation sites and also to clarify contradictory results from previous literature, we proposed an ex situ characterization method that is allowed to characterize exactly the same inclusion or location of the surface of steel before and after corrosion tests. The time-dependent corrosion behaviour of the inclusions and the surrounding X100 steel matrix at the same area before and after early stage immersion in a near-neutral pH bicarbonate solution was investigated by ex situ scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) analysis and localized electrochemical impedance spectroscopy (LEIS). The sizes of most inclusions in X100 steel are below 3 μm. The results challenge the long-held opinion of previous work that corrosion pit initiations are related with the inclusions. It has been found that most of the inclusions remain stable (intact) during the whole testing time although severe corrosion occurs on the matrix of the steel. The chemical composition of the inclusion greatly affects the chemical stability of the inclusion. SiO 2 inclusions and complex inclusions with a high SiO 2 content remain intact although obvious general corrosion occurs on the steel matrix under the investigated immersion period. Inclusions with little Si, such as Al–Mg–Ca–O enriched inclusions, totally disappear after certain immersion time. During the immersion, the corrosion product tends to deposit at the interstice between the inclusion and steel matrix. - Highlights: • Ex situ characterization of metallurgical inclusions in X100 pipeline steel. • The pipeline steel was immersed in neutral pH bicarbonate solution. • Majority of inclusions remain stable during the whole testing time. • The chemical stability of metallurgical inclusions depends on the SiO 2 content.

  14. Triton burnup study using scintillating fiber detector on JT-60U

    Energy Technology Data Exchange (ETDEWEB)

    Harano, Hideki [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

    1997-09-01

    The DT fusion reactor cannot be realized without knowing how the fusion-produced 3.5 MeV {alpha} particles behave. The {alpha} particles` behavior can be simulated using the 1 MeV triton. To investigate the 1 MeV triton`s behavior, a new type of directional 14 MeV neutron detector, scintillating fiber (Sci-Fi) detector has been developed and installed on JT-60U in the cooperation with LANL as part of a US-Japan collaboration. The most remarkable feature of the Sci-Fi detector is that the plastic scintillating fibers are employed for the neutron sensor head. The Sci-Fi detector measures and extracts the DT neutrons from the fusion radiation field in high time resolution (10 ms) and wide dynamic range (3 decades). Triton burnup analysis code TBURN has been made in order to analyze the time evolution of DT neutron emission rate obtained by the Sci-Fi detector. The TBURN calculations reproduced the measurements fairly well, and the validity of the calculation model that the slowing down of the 1 MeV triton was classical was confirmed. The Sci-Fi detector`s directionality indicated the tendency that the DT neutron emission profile became more and more peaked with the time progress. In this study, in order to examine the effect of the toroidal field ripple on the triton burnup, R{sub p}-scan and n{sub e}-scan experiments have been performed. The R{sub p}-scan experiment indicates that the triton`s transport was increased as the ripple amplitude over the triton became larger. In the n{sub e}-scan experiment, the DT neutron emission showed the characteristic changes after the gas puffing injection. It was theoretically confirmed that the gas puffing was effective for the collisionality scan. (J.P.N.) 127 refs.

  15. The influence of thermal inertia on temperatures and frost stability on Triton

    Science.gov (United States)

    Spencer, John R.; Moore, Jeffrey M.

    1992-01-01

    It is presently argued, in view of (1) a thermal inertia model for the surface of Triton which (like previous ones) predicts a monotonic recession of permanent N2 deposits toward the poles and very little seasonal N2 frost in the southern hemisphere, and (2) new spectroscopic evidence for nonvolatile CO2 on Triton's bright southern hemisphere, that much of that bright southern material is not N2. Such bright southern hemisphere volatiles may allow the formation of seasonal frosts, thereby helping to explain the observed spectroscopic changes of Triton during the last decade.

  16. MICROBIAL SURFACTANTS. I. GLYCOLIPIDS

    Directory of Open Access Journals (Sweden)

    Pirog T. Р.

    2014-02-01

    Full Text Available The review is devoted to surface-active glycolipids. The general characteristics, the physiological role of the rhamnolipids, trehalose lipids, sophorolipids, mannosylerythritol lipids and their traditional producers — the representatives of the genera Pseudozyma, Pseudomonas, Rhodococcus and Candida are given. The detailed analysis of the chemical structure, the stages of the biosynthesis and the regulation of some low molecular glycolipids are done. The own experimental data concerning the synthesis intensification, the physiological role and the practical use of Rhodococcus erythropolis IMV Ac-5017, Acinetobacter calcoaceticus IMV B-7241 and Nocardia vaccinii IMV B-7405 surfactants, which are a complex of the glyco-, phospho-, amino- and neutral lipids (glycolipids of all strains are presented by trehalose mycolates are summarized. It was found that R. erythropolis IMV Ac-5017, A. calcoaceticus IMV B-7241 and N. vaccinii IMV B-7405 surfactants have protective, antimicrobial and antiadhesive properties. It was shown that R. erythropolis IMV Ac-5017, A. calcoaceticus IMV B-7241 and N. vaccinii IMV B-7405 surfactants preparation of cultural liquid intensified the degradation of oil in water due to the activation of the natural petroleum-oxidizing microflora.

  17. Surfactants at the Design Limit.

    Science.gov (United States)

    Czajka, Adam; Hazell, Gavin; Eastoe, Julian

    2015-08-04

    This article analyzes how the individual structural elements of surfactant molecules affect surface properties, in particular, the point of reference defined by the limiting surface tension at the aqueous cmc, γcmc. Particular emphasis is given to how the chemical nature and structure of the hydrophobic tails influence γcmc. By comparing the three different classes of surfactants, fluorocarbon, silicone, and hydrocarbon, a generalized surface packing index is introduced which is independent of the chemical nature of the surfactants. This parameter ϕcmc represents the volume fraction of surfactant chain fragments in a surface film at the aqueous cmc. It is shown that ϕcmc is a useful index for understanding the limiting surface tension of surfactants and can be useful for designing new superefficient surfactants.

  18. Effects of H2S/HS- on Stress Corrosion Cracking Behavior of X100 Pipeline Steel Under Simulated Sulfate-Reducing Bacteria Metabolite Conditions

    Science.gov (United States)

    Liu, Q.; Li, Z.; Liu, Z. Y.; Li, X. G.; Wang, S. Q.

    2017-04-01

    The effect of H2S/HS-, which simulates the main metabolites of sulfate-reducing bacteria (SRB), on the electrochemical and stress corrosion cracking (SCC) behaviors of X100 steel was investigated in a near-neutral solution. The results showed that different H2S/HS- contents mainly affected the cathodic process of X100 electrochemical corrosion. As the concentration of H2S/HS- increased, the corrosion potential was shifted negatively, the corrosion current density was considerably increased, and the corrosion rate was linearly increased. Different rust layers with shifting structures were formed under different conditions and had different effects on electrochemical behaviors. However, sulfide mainly promoted local corrosion processes. With the synergistic effects of stress and H2S/HS-, SCC susceptibility was considerably enhanced. The accelerated process of hydrogen evolution by sulfide was crucial in enhancing SCC processes. In brief, the trace H2S/HS- generated by SRB metabolites played a positive role in promoting SCC.

  19. Increased release of fermentable sugars from elephant grass by enzymatic hydrolysis in the presence of surfactants

    International Nuclear Information System (INIS)

    Menegol, Daiane; Scholl, Angélica Luisi; Fontana, Roselei Claudete; Dillon, Aldo José Pinheiro; Camassola, Marli

    2014-01-01

    Highlights: • Milling is an attractive method to enhance the enzymatic hydrolysis of biomass. • Surfactants improve the efficiency of lignocellulose enzymatic hydrolysis. • Pretreatment with NaOH, smaller particle size and Tween 80® were more efficient. - Abstract: In the search for renewable energy sources, elephant grass is an alternative substrate for ethanol production, but this substrate must be hydrolyzed by cellulases and xylanases to liberate fermentable sugars. During enzymatic hydrolysis, cellulase activity is reduced by the irreversible adsorption of cellulase onto cellulose, decreasing the rate of hydrolysis. Adding surfactants during hydrolysis can improve the process. The effects of Tween® and Triton® surfactants on the enzymatic hydrolysis of elephant grass were evaluated in this context. The data indicate that pretreatment with sodium hydroxide, along with a smaller particle size (0.075–0.152 mm) and the use of Tween 80®, increased the efficiency of releasing reducing sugars from pretreated elephant grass biomass. Thus, it is possible to reduce grinding costs in second-generation ethanol production through the use of surfactants, as they allow efficient hydrolysis of larger biomass particles

  20. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 2000-present, Longwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Incoming Longwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  1. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 2000-present, Longwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Incoming Longwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  2. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 2000-present, Longwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Incoming Longwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  3. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 2000-present, Longwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Incoming Longwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  4. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 1980-present, Position

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Position data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  5. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1980-present, Position

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Position data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  6. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1991-present, Net Shortwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Net Shortwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  7. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 2000-present, Net Longwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Net Longwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  8. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1998-present, Barometric (Air) Pressure

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Barometric (Air) Pressure data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  9. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1977-present, Air Temperature

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Air Temperature data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  10. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1987-present, Salinity

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Salinity data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  11. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1989-present, Wind Stress

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Wind Stress data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  12. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1980-present, Position

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Position data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  13. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1980-present, Position

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Position data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  14. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1977-present, Currents

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Currents data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  15. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1992-present, Sea Surface Salinity

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Sea Surface Salinity data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  16. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 2000-present, Buoyancy Flux

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Buoyancy Flux data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  17. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 2000-present, Net Longwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Net Longwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  18. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1987-present, Potential Density Anomaly

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Potential Density Anomaly (sigma-theta) data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  19. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1989-present, Sensible Heat Flux

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Sensible Heat Flux data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  20. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1989-present, Sensible Heat Flux

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Sensible Heat Flux data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  1. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1977-present, Temperature

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Temperature data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  2. Effects of sawtooth crashes on beam ions and fusion product tritons in JET

    International Nuclear Information System (INIS)

    Marcus, F.B.; Hone, M.A.; Jarvis, O.N.; Loughlin, M.J.; Sadler, G.

    1994-01-01

    The effect of a sawtooth crash on the radial distribution of the slowing down fusion product tritons and on beams ions, is examined with measurements of the 2.5 MeV and 14 MeV neutron emission line-integrals before and after sawtooth crashes. In deuterium discharges, the 14 MeV neutron production was wholly attributable to burnup of the 1 MeV fusion product tritons from d-d fusion. The local emissivity of 14 MeV neutrons, and hence of the profile of thermalizing tritons, is shown to be only weakly affected by crashes in the discharges studied. This is in contradiction with the apparent behaviour of injected beam ions as deduced from a study of the considerable changes in local emissivity of the 2.5 MeV neutrons. Nevertheless, the behaviour of the fusion product tritons is consistent with the scaling of the beam injected deuterium. 1 ref., 6 figs

  3. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1989-present, Sensible Heat Flux

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Sensible Heat Flux data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  4. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 1989-present, Relative Humidity

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Relative Humidity data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  5. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1989-present, Relative Humidity

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Relative Humidity data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  6. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1989-present, Relative Humidity

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Relative Humidity data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  7. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1989-present, Relative Humidity

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Relative Humidity data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  8. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 1989-present, Wind Stress

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Wind Stress data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  9. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1988-2015, ADCP

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Acoustic Doppler Current Profiler (ADCP) water currents data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA...

  10. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 1988-2015, ADCP

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Acoustic Doppler Current Profiler (ADCP) water currents data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA...

  11. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1997-present, Heat Flux Due To Rain

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Heat Flux Due To Rain data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  12. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 1997-present, Precipitation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Precipitation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  13. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1901-present, Downgoing Shortwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Downgoing Shortwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  14. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1991-present, Downgoing Shortwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Downgoing Shortwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  15. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1997-present, Precipitation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Precipitation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  16. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 1991-present, Downgoing Shortwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Downgoing Shortwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  17. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1991-present, Downgoing Shortwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Downgoing Shortwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  18. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1997-present, Precipitation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Precipitation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  19. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1989-present, Wind Stress

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Wind Stress data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  20. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1998-present, Barometric (Air) Pressure

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Barometric (Air) Pressure data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  1. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 1992-present, Sea Surface Salinity

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Sea Surface Salinity data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  2. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 2000-present, Net Longwave Radiation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Net Longwave Radiation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  3. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1992-present, Sigma-Theta

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Sigma-Theta (Potential Density Anomaly) data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  4. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 1997-present, Evaporation Minus Precipitation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Evaporation Minus Precipitation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  5. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1977-present, Currents

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Currents data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  6. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1977-present, 20C Isotherm Depth

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly 20C Isotherm Depth data (the depth at which the ocean temperature is 20C) from the TAO/TRITON (Pacific Ocean,...

  7. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1989-present, Evaporation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Evaporation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  8. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1997-present, Evaporation Minus Precipitation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Evaporation Minus Precipitation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  9. Effects of sawtooth crashes on beam ions and fusion product tritons in JET

    Energy Technology Data Exchange (ETDEWEB)

    Marcus, F.B.; Hone, M.A.; Jarvis, O.N.; Loughlin, M.J.; Sadler, G. [Commission of the European Communities, Abingdon (United Kingdom). JET Joint Undertaking; Adams, J.M.; Bond, D.S.; Watkins, N. [UKAEA Harwell Lab. (United Kingdom). Energy Technology Div.; Howarth, P.J.A. [Birmingham Univ. (United Kingdom)

    1994-07-01

    The effect of a sawtooth crash on the radial distribution of the slowing down fusion product tritons and on beams ions, is examined with measurements of the 2.5 MeV and 14 MeV neutron emission line-integrals before and after sawtooth crashes. In deuterium discharges, the 14 MeV neutron production was wholly attributable to burnup of the 1 MeV fusion product tritons from d-d fusion. The local emissivity of 14 MeV neutrons, and hence of the profile of thermalizing tritons, is shown to be only weakly affected by crashes in the discharges studied. This is in contradiction with the apparent behaviour of injected beam ions as deduced from a study of the considerable changes in local emissivity of the 2.5 MeV neutrons. Nevertheless, the behaviour of the fusion product tritons is consistent with the scaling of the beam injected deuterium. 1 ref., 6 figs.

  10. TAO/TRITON, RAMA, and PIRATA Buoys, Monthly, 1989-present, Evaporation

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has monthly Evaporation data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  11. TAO/TRITON, RAMA, and PIRATA Buoys, Daily, 1992-present, Sea Surface Salinity

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has daily Sea Surface Salinity data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  12. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 1977-present, Temperature

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day Temperature data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  13. TAO/TRITON, RAMA, and PIRATA Buoys, Quarterly, 1980-present, Heat Content

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has quarterly Heat Content data from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/ ), RAMA (Indian Ocean,...

  14. Surfactant phosphatidylcholine metabolism and surfactant function in preterm, ventilated lambs

    International Nuclear Information System (INIS)

    Jobe, A.H.; Ikegami, M.; Seidner, S.R.; Pettenazzo, A.; Ruffini, L.

    1989-01-01

    Preterm lambs were delivered at 138 days gestational age and ventilated for periods up to 24 h in order to study surfactant metabolism and surfactant function. The surfactant-saturated phosphatidylcholine pool in the alveolar wash was 13 +/- 4 mumol/kg and did not change from 10 min to 24 h after birth. Trace amounts of labeled natural sheep surfactant were mixed with fetal lung fluid at birth. By 24 h, 80% of the label had become lung-tissue-associated, yet there was no loss of label from phosphatidylcholine in the lungs when calculated as the sum of the lung tissue plus alveolar wash. De novo synthesized phosphatidylcholine was labeled with choline given by intravascular injection at 1 h of age. Labeled phosphatidylcholine accumulated in the lung tissue linearly to 24 h, and the labeled phosphatidylcholine moved through lamellar body to alveolar pools. The turnover time for alveolar phosphatidylcholine was estimated to be about 13 h, indicating an active metabolic pool. A less surface-active surfactant fraction recovered as a supernatant after centrifugation of the alveolar washes at 40,000 x g increased from birth to 10 min of ventilation, but no subsequent changes in the distribution of surfactant phosphatidylcholine in surfactant fractions occurred. The results were consistent with recycling pathway(s) that maintained surface-active surfactant pools in preterm ventilated lambs

  15. Study of surfactant-added TMAH for applications in DRIE and wet etching-based micromachining

    Science.gov (United States)

    Tang, B.; Shikida, M.; Sato, K.; Pal, P.; Amakawa, H.; Hida, H.; Fukuzawa, K.

    2010-06-01

    In this paper, etching anisotropy is evaluated for a number of different crystallographic orientations of silicon in a 0.1 vol% Triton-X-100 added 25 wt% tetramethylammonium hydroxide (TMAH) solution using a silicon hemisphere. The research is primarily aimed at developing advanced applications of wet etching in microelectromechanical systems (MEMS). The etching process is carried out at different temperatures in the range of 61-81 °C. The etching results of silicon hemisphere and different shapes of three-dimensional structures in {1 0 0}- and {1 1 0}-Si surfaces are analyzed. Significantly important anisotropy, different from a traditional etchant (e.g. pure KOH and TMAH), is investigated to extend the applications of the wet etching process in silicon bulk micromachining. The similar etching behavior of exact and vicinal {1 1 0} and {1 1 1} planes in TMAH + Triton is utilized selectively to remove the scalloping from deep reactive-ion etching (DRIE) etched profiles. The direct application of the present research is demonstrated by fabricating a cylindrical lens with highly smooth etched surface finish. The smoothness of a micro-lens at different locations is measured qualitatively by a scanning electron microscope and quantitatively by an atomic force microscope. The present paper provides a simple and effective fabrication method of the silicon micro-lens for optical MEMS applications.

  16. ADSORPTION OF SURFACTANT ON CLAYS

    Science.gov (United States)

    Surfactants used to enhance remediation of soils by soil washing are often lost in the process. Neither the amount nor the cause of this loss is known. It is assumed that clays present in the soil are responsible for the loss of the surfactant. In this papere, adsorption prope...

  17. Surfactant monitoring by foam generation

    Science.gov (United States)

    Mullen, Ken I.

    1997-01-01

    A device for monitoring the presence or absence of active surfactant or other surface active agents in a solution or flowing stream based on the formation of foam or bubbles is presented. The device detects the formation of foam with a light beam or conductivity measurement. The height or density of the foam can be correlated to the concentration of the active surfactant present.

  18. 400Gb/s (4 x 100Gb/s) orthogonal PDM-RZ-QPSK DWDM signal transmission over 1040km SMF-28.

    Science.gov (United States)

    Yu, Jianjun; Zhou, Xiang; Huang, Ming-Fang; Qian, Dayou; Ji, Philip N; Wang, Ting; Magill, Peter

    2009-09-28

    We have generated 4 x 100-Gb/s orthogonal WDM optical signal by employing polarization-division-multiplexed (PDM) return-to-zero (RZ) QPSK modulation format and tight optical filtering technique. The required optical signal-to-noise ratio (OSNR) at bit error ratio (BER) of 2 x 10(-3) for the 400 Gb/s orthogonal DWDM signal is measured to be approximately 22.8 dB/0.1 nm. After transmission over 1040-km standard single mode fiber (EDFA-only amplification, 80-km amplifier span and fully receiver-side electrical dispersion compensation), the measured BER for all the four orthogonal subchannels are smaller than 2 x 10(-3).

  19. Corrosion Cyclic Voltammetry of Two Types of Heat-Affected Zones (HAZs) of API-X100 Steel in Bicarbonate Solutions

    Science.gov (United States)

    Eliyan, Faysal Fayez; Alfantazi, Akram

    2014-12-01

    This paper examined the electrochemical corrosion behavior and corrosion products of two types of heat-affected HAZs made from API-X100 steel. Cyclic voltammetry, with different scan rates and potential ranges at 10 cycles, was applied to analyze the interdependent corrosion reactions of cathodic reduction, anodic dissolution, passivation, and transpassivation. The HAZ cooled at 60 K/s, from a peak temperature of 1470 K (1197 °C) that was held for 15 seconds, exhibited better passivation and lower cathodic activity than the HAZ cooled at 10 K/s. Increasing bicarbonate concentration, from 0.05 and 0.2 to 0.6 M, increases the anodic activity and cathodic reduction, but accordingly protects the active surfaces and enhances passivation.

  20. MICROBIAL SURFACTANTS IN ENVIRONMENTAL TECHNOLOGIES

    Directory of Open Access Journals (Sweden)

    T. P. Pirog

    2015-08-01

    Full Text Available It was shown literature and own experimental data concerning the use of microbial surface active glycolipids (rhamno-, sophoro- and trehalose lipids and lipopeptides for water and soil purification from oil and other hydrocarbons, removing toxic heavy metals (Cu2+, Cd2+, Ni2+, Pb2+, degradation of complex pollution (oil and other hydrocarbons with heavy metals, and the role of microbial surfactants in phytoremediation processes. The factors that limit the use of microbial surfactants in environmental technologies are discussed. Thus, at certain concentrations biosurfactant can exhibit antimicrobial properties and inhibit microorganisms destructing xenobiotics. Microbial biodegradability of surfactants may also reduce the effectiveness of bioremediation. Development of effective technologies using microbial surfactants should include the following steps: monitoring of contaminated sites to determine the nature of pollution and analysis of the autochthonous microbiota; determining the mode of surfactant introduction (exogenous addition of stimulation of surfactant synthesis by autochthonous microbiota; establishing an optimal concentration of surfactant to prevent exhibition of antimicrobial properties and rapid biodegradation; research both in laboratory and field conditions.

  1. Structural Studies of Protein-Surfactant Complexes

    International Nuclear Information System (INIS)

    Chodankar, S. N.; Aswal, V. K.; Wagh, A. G.

    2008-01-01

    The structure of protein-surfactant complexes of two proteins bovine serum albumin (BSA) and lysozyme in presence of anionic surfactant sodium dodecyl sulfate (SDS) has been studied using small-angle neutron scattering (SANS). It is observed that these two proteins form different complex structures with the surfactant. While BSA protein undergoes unfolding on addition of surfactant, lysozyme does not show any unfolding even up to very high surfactant concentrations. The unfolding of BSA protein is caused by micelle-like aggregation of surfactant molecules in the complex. On the other hand, for lysozyme protein there is only binding of individual surfactant molecules to protein. Lysozyme in presence of higher surfactant concentrations has protein-surfactant complex structure coexisting with pure surfactant micelles

  2. Activity, stability and kinetic parameters for α-chymotrypsin catalysed ...

    Indian Academy of Sciences (India)

    Three typical surfactants were selected based on their head group charges: a non-ionic surfactant Triton-X 100 and two zwitterionic sulphobetaine surfactants of the type CH2+1N+Me2 (CH2)3 SO 3 − (n = 10; SB3-10, n = 16; SB3-16). The kinetic parameters (such as cat and M) of the -CT at 27°C were determined ...

  3. Surfactant Membrane Phases Containing Mixtures of Hydrocarbon and Fluorocarbon Surfactants

    International Nuclear Information System (INIS)

    de Campo, Liliana; Warr, G.G.

    2005-01-01

    Full text: We describe the structure and stability of sponge and lamellar phases comprising mixtures of hydrocarbon and fluorocarbon surfactants. Such mixtures can show limited miscibility with each other, forming for example coexisting populations of hydrocarbon rich and fluorocarbon rich micelles under some circumstances. Our system is based on the well-characterised lamellar and sponge phases of cetylpyridinium chloride, hexanol and 0.2M brine, into which the partially fluorinated surfactant N-1H,1H,2H,2H-tridecafluorooctylpyridinium chloride is incorporated. By probing the structures with SAXS (small angle x-ray scattering) and SANS (small angle neutron scattering) using contrast variation, and by characterizing the dynamic properties with dynamic light scattering, we will describe the effect of incorporating the fluorinated surfactant on the phase equilibria and properties of the surfactant membrane structures. (authors)

  4. Influence of elastase-induced emphysema and the inhalation of an irritant aerosol on deposition and retention of an inhaled insoluble aerosol in Fischer-344 rats

    International Nuclear Information System (INIS)

    Damon, E.G.; Mokler, B.V.; Jones, R.K.

    1983-01-01

    The purpose of this study was to assess the effects of elastase-induced pulmonary emphysema and the inhalation of an irritant aerosol (Triton X-100, a nonionic surfactant similar to those used in a number of pressurized consumer products) on pulmonary deposition and retention of an insoluble test aerosol, 59 FE-labeled Fe 2 O 3 . Untreated rats or rats pretreated by intratracheal in stillation with elastase were exposed to an aerosol of 59 Fe-labeled Fe 2 O 3 either 18 hr or 7 days after exposure to aerosslized Triton X-100 which was administered in doses of 20, 100, or 200 μg/g of lung. Rats pretreated with elastase had significantly lower pulmonary deposition of 59 Fe than the untreated controls (p 2 O 3 was unaffected by pretreatment with Triton X-100. Elastase treatment alone had no effect on retention of Fe 2 O 3 . Triton X-100 administered 18 hr prior to exposure of rats to Fe 2 O 3 aerosol resulted in dose-related increases in whole-body retention of 59 Fe. When rats were exposed to Triton X-100 7 days before exposure to Fe 2 O 3 , increased retention of 59 Fe was noted only in those treated at the highest Triton X-100 dose level (200 μg/g). 20 references, 5 tables

  5. Treatment with exogenous surfactant stimulates endogenous surfactant synthesis in premature infants with respiratory distress syndrome

    NARCIS (Netherlands)

    Bunt, JEH; Carnielli, VP; Janssen, DJ; Wattimena, JLD; Hop, WC; Sauer, PJ; Zimmermann, LJI

    2000-01-01

    Objective: Treatment of preterm infants with respiratory distress syndrome (RDS) with exogenous surfactant has greatly improved clinical outcome. Some infants require multiple doses, and it has not been studied whether these large amounts of exogenous surfactant disturb endogenous surfactant

  6. Micellar phase boundaries under the influence of ethyl alcohol

    International Nuclear Information System (INIS)

    Bergeron, Denis E.

    2016-01-01

    The Compton spectrum quenching technique is used to monitor the effect of ethyl alcohol (EtOH) additions on phase boundaries in two systems. In toluenic solutions of the nonionic surfactant, Triton X-100, EtOH shifts the boundary separating the first clear phase from the first turbid phase to higher water:surfactant ratios. In a commonly used scintillant, Ultima Gold AB, the critical micelle concentration is not shifted. The molecular interactions behind the observations and implications for liquid scintillation counting are discussed. - Highlights: • Compton spectrum quenching technique applied to find micellar phase boundaries. • Toluenic Triton X-100 and Ultima Gold AB investigated. • Ethyl alcohol affects phase boundaries in Triton X-100, not in Ultima Gold AB. • Phase boundary observations discussed in terms of relevant molecular interactions.

  7. Polarized triton scattering from 26Mg, 27Al and 28Si at 17 MeV

    International Nuclear Information System (INIS)

    Hardekopf, R.A.; Brown, R.E.; Correll, F.D.; Ohlsen, G.G.

    1980-01-01

    Differential-cross-section and analyzing-power angular distributions were measured for 17 MeV tritons elastically scattered from targets of 26 Mg, 27 Al, and 28 Si in the angular range 20 to 160 0 . The experiment was performed at the Los Alamos Scientific Laboratory Van de Graaff facility using the Lamb-shift polarized triton source and the supercube scattering chamber. A pair of detector telescopes with angular resolutions of +-0.4 0 detected the reaction products, with mass identification and storage performed by an on-line computer. The triton beam intensity available at the target was about 70 nA with a polarization of 0.77. The target thicknesses were about 3 mg/cm 2 , although thinner targets were used for the 27 Al forward-angle data

  8. Burnup of fusion produced tritons and 3He ions in PLT and PDX

    International Nuclear Information System (INIS)

    Heidbrink, W.W.; Chrien, R.E.; Strachan, J.D.

    1982-09-01

    The d(d,p)t and d(d,n) 3 He fusion reactions produce 1 MeV tritons and 0.8 MeV 3 He ions which can subsequently undergo d(t,n)α and d( 3 He,p)α fusion reactions. The magnitude of this triton and 3 He ion burnup was measured on the PLT and PDX tokamaks by detection of the 14 MeV neutron and 15 MeV proton emission. In discharges with B/sub phi/ greater than or equal to 2 T, the measured 3 He burnup agrees well with predictions based on classical theories of ion confinement and slowing down, while the triton burnup was about four times lower than theoretically predicted. In discharges with weaker toroidal fields, the burnup of both ions fell by more than a factor of ten

  9. Biomimicry of surfactant protein C.

    Science.gov (United States)

    Brown, Nathan J; Johansson, Jan; Barron, Annelise E

    2008-10-01

    Since the widespread use of exogenous lung surfactant to treat neonatal respiratory distress syndrome, premature infant survival and respiratory morbidity have dramatically improved. Despite the effectiveness of the animal-derived surfactant preparations, there still remain some concerns and difficulties associated with their use. This has prompted investigation into the creation of synthetic surfactant preparations. However, to date, no clinically used synthetic formulation is as effective as the natural material. This is largely because the previous synthetic formulations lacked analogues of the hydrophobic proteins of the lung surfactant system, SP-B and SP-C, which are critical functional constituents. As a result, recent investigation has turned toward the development of a new generation of synthetic, biomimetic surfactants that contain synthetic phospholipids along with a mimic of the hydrophobic protein portion of lung surfactant. In this Account, we detail our efforts in creating accurate mimics of SP-C for use in a synthetic surfactant replacement therapy. Despite SP-C's seemingly simple structure, the predominantly helical protein is extraordinarily challenging to work with given its extreme hydrophobicity and structural instability, which greatly complicates the creation of an effective SP-C analogue. Drawing inspiration from Nature, two promising biomimetic approaches have led to the creation of rationally designed biopolymers that recapitulate many of SP-C's molecular features. The first approach utilizes detailed SP-C structure-activity relationships and amino acid folding propensities to create a peptide-based analogue, SP-C33. In SP-C33, the problematic and metastable polyvaline helix is replaced with a structurally stable polyleucine helix and includes a well-placed positive charge to prevent aggregation. SP-C33 is structurally stable and eliminates the association propensity of the native protein. The second approach follows the same design

  10. Four-channel ZnS scintillator measurements of escaping tritons in TFTR

    Energy Technology Data Exchange (ETDEWEB)

    Zweben, S.J.

    1988-10-01

    A four-channel scintillation detector capable of measuring tritons, protons, and alphas escaping from a tokamak plasma was operated during the 1986 run period of the Tokamak Fusion Test Reactor (TFTR). Signals consistent with the expected 1 MeV triton behavior have been observed during deuterium operation. Backgrounds associated with neutrons, gammas, and soft x-rays have been evaluated in situ. Such a detector should be capable of measuring escaping alphas during the D/T phase of TFTR. 16 refs., 10 figs.

  11. Triton-3He relative and differential flows and the high density behavior of nuclear symmetry

    International Nuclear Information System (INIS)

    Yong, Gaochan; Li, Baoan; Chen, Liewen

    2010-01-01

    Using a transport model coupled with a phase-space coalescence after-burner we study the triton- 3 He relative and differential transverse flows in semi-central 132 Sn + 124 Sn reactions at a beam energy of 400 MeV/nucleon. We find that the triton- 3 He pairs carry interesting information about the density dependence of the nuclear symmetry energy. The t- 3 He relative flow can be used as a particularly powerful probe of the high-density behavior of the nuclear symmetry energy. (author)

  12. Four-channel ZnS scintillator measurements of escaping tritons in TFTR

    International Nuclear Information System (INIS)

    Zweben, S.J.

    1988-10-01

    A four-channel scintillation detector capable of measuring tritons, protons, and alphas escaping from a tokamak plasma was operated during the 1986 run period of the Tokamak Fusion Test Reactor (TFTR). Signals consistent with the expected 1 MeV triton behavior have been observed during deuterium operation. Backgrounds associated with neutrons, gammas, and soft x-rays have been evaluated in situ. Such a detector should be capable of measuring escaping alphas during the D/T phase of TFTR. 16 refs., 10 figs

  13. Tritons for the study of the charge-exchange reactions with the LHE streamer chamber: status and some possibilities

    International Nuclear Information System (INIS)

    Avramenko, S.A.; Belikov, Yu.A.; Golokhvastov, A.I.; Kirillov, A.D.; Khorozov, S.A.; Komolov, L.N.; Lukstin'sh, Yu.; Rukoyatkin, P.A.

    1997-01-01

    The 6 and 9 GeV/c secondary tritons, produced in the 4 He+A→ 3 H+X reaction, were used to study the charge-exchange reactions using a streamer chamber in magnetic field. The triton formation schemes, the beam parameters achieved as well as a way to reduce the beam momentum spread are given in the paper

  14. Modeling of the water gap in BWR fuel elements using SCALE/TRITON; Modellierung des Wasserspalts bei SWR-BE mit SCALE/TRITON

    Energy Technology Data Exchange (ETDEWEB)

    Tittelbach, S.; Chernykh, M. [WTI Wissenschaftlich-Technische Ingenieurberatung GmbH, Juelich (Germany)

    2012-11-01

    The authors show that an adequate modeling of the water gap in BWR fuel element models using the code TRITON requires an explicit consideration of the Dancoff factors. The analysis of three modeling options reveals that considering the moderating effects of the water gap coolant for the peripheral fuel elements the resulting deviations of the U-235 and Pu-239 concentrations are significantly reduced. The increased temporal calculation efforts are justified with respect to the burnup credits for criticality safety analyses.

  15. Fungal growth on anion surfactant medium.

    Science.gov (United States)

    Hamada, Nobuo; Abe, Niichiro

    2009-12-01

    Before the present study, no fungi using anion surfactant as a nutrient had been identified, although some fungi were known to use nonion surfactant. Washing water collected from 63 washing machines was inoculated onto 0.1% LAS (Sodium dodecyl benzenesulfonate) anion surfactant media to identify fungi that can feed on anion-surfactant. Small dark colonies of fungi were found on several of the Petri-dishes from 12 days after inoculation. These were identified as Cladophialophora boppii and Exophiala spinifera using morphological features and rDNA data. A number of the isolates of C. boppii specifically were recognized as using anion surfactant as a nutrient. The growth characteristics of the two fungal species were examined on surfactant media of three kinds. Apart from anion surfactant, the fungi were also able to grow on nonion surfactant and on soap. The application of these fungi for environmental cleansing after detergent pollution is also discussed.

  16. Synthesis of carbohydrate-based surfactants

    Science.gov (United States)

    Pemberton, Jeanne E.; Polt, Robin L.; Maier, Raina M.

    2016-11-22

    The present invention provides carbohydrate-based surfactants and methods for producing the same. Methods for producing carbohydrate-based surfactants include using a glycosylation promoter to link a carbohydrate or its derivative to a hydrophobic compound.

  17. Optimized triton X-114 assisted lipopolysaccharide (LPS) removal method reveals the immunomodulatory effect of food proteins

    NARCIS (Netherlands)

    Teodorowicz, Malgorzata; Perdijk, Olaf; Verhoek, Iris; Govers, Coen; Savelkoul, Huub F.J.; Tang, Yongfu; Wichers, Harry; Broersen, Kerensa

    2017-01-01

    Scope Investigations into the immunological response of proteins is often masked by lipopolysaccharide (LPS) contamination. We report an optimized Triton X-114 (TX-114) based LPS extraction method for β-lactoglobulin (BLG) and soy protein extract suitable for cell-based immunological assays.

  18. Optimized triton X-114 assisted lipopolysaccharide (LPS) removal method reveals the immunomodulatory effect of food proteins

    NARCIS (Netherlands)

    Teodorowicz, Malgorzata; Perdijk, Olaf; Verhoek, Iris; Govers, Coen; Savelkoul, Huub F.J.; Tang, Yongfu; Wichers, Harry; Broersen, Kerensa

    2017-01-01

    Scope Investigations into the immunological response of proteins is often masked by lipopolysaccharide (LPS) contamination. We report an optimized Triton X-114 (TX-114) based LPS extraction method for β-lactoglobulin (BLG) and soy protein extract suitable for cell-based immunological assays. Methods

  19. The asymptotic D-state to S-state ratio of triton

    Indian Academy of Sciences (India)

    dictions of the asymptotic D-state to S-state ratio of triton are calculated to more fully evaluate the adequacy of the ... deuteron radiative capture was also calculated at thermal neutron energies, using pionless. EFT up to N2LO ... necessary for this work and the derivation of the integral equation describing neutron– deuteron ...

  20. TAO/TRITON, RAMA, and PIRATA Buoys, 5-Day, 1977-present, 20C Isotherm Depth

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has 5-day 20C Isotherm Depth data (the depth at which the ocean temperature is 20C) from the TAO/TRITON (Pacific Ocean, https://www.pmel.noaa.gov/gtmba/...

  1. Surfactant Therapy of ALI and ARDS

    OpenAIRE

    Raghavendran, K; Willson, D; Notter, RH

    2011-01-01

    This article examines exogenous lung surfactant replacement therapy and its utility in mitigating clinical acute lung injury (ALI) and the acute respiratory distress syndrome (ARDS). Biophysical research has documented that lung surfactant dysfunction can be reversed or mitigated by increasing surfactant concentration, and multiple studies in animals with ALI/ARDS have shown that respiratory function and pulmonary mechanics in vivo can be improved by exogenous surfactant administration. Exoge...

  2. Cationic surfactants as the hydrolytic micellar catalysts

    OpenAIRE

    Janošcová, Petra

    2013-01-01

    Cationic surfactants as the hydrolytic micellar catalysts Petra Janošcová The effectiveness of hydrolytic cleavage of the pesticide fenitrothionin cationic surfactants micellar media has been tested. All used surfactants increased the rate of fenitrothionhydrolysis, which was the evidence of micellar catalysis. For some surfactants decreases has been evident at the highest rate of hydrolysis concentrations. It has been the result of a phenomenon called the effect of empty micelles. High hydro...

  3. ICE MINERALOGY ACROSS AND INTO THE SURFACES OF PLUTO, TRITON, AND ERIS

    International Nuclear Information System (INIS)

    Tegler, S. C.; Grundy, W. M.; Olkin, C. B.; Young, L. A.; Romanishin, W.; Cornelison, D. M.; Khodadadkouchaki, R.

    2012-01-01

    We present three near-infrared spectra of Pluto taken with the Infrared Telescope Facility and SpeX, an optical spectrum of Triton taken with the MMT and the Red Channel Spectrograph, and previously published spectra of Pluto, Triton, and Eris. We combine these observations with a two-phase Hapke model and gain insight into the ice mineralogy on Pluto, Triton, and Eris. Specifically, we measure the methane-nitrogen mixing ratio across and into the surfaces of these icy dwarf planets. In addition, we present a laboratory experiment that demonstrates it is essential to model methane bands in spectra of icy dwarf planets with two methane phases—one highly diluted by nitrogen and the other rich in methane. For Pluto, we find bulk, hemisphere-averaged, methane abundances of 9.1% ± 0.5%, 7.1% ± 0.4%, and 8.2% ± 0.3% for sub-Earth longitudes of 10°, 125°, and 257°. Application of the Wilcoxon rank sum test to our measurements finds these small differences are statistically significant. For Triton, we find bulk, hemisphere-averaged, methane abundances of 5.0% ± 0.1% and 5.3% ± 0.4% for sub-Earth longitudes of 138° and 314°. Application of the Wilcoxon rank sum test to our measurements finds the differences are not statistically significant. For Eris, we find a bulk, hemisphere-averaged, methane abundance of 10% ± 2%. Pluto, Triton, and Eris do not exhibit a trend in methane-nitrogen mixing ratio with depth into their surfaces over the few centimeter range probed by these observations. This result is contrary to the expectation that since visible light penetrates deeper into a nitrogen-rich surface than the depths from which thermal emission emerges, net radiative heating at depth would drive preferential sublimation of nitrogen leading to an increase in the methane abundance with depth.

  4. Binding of cationic surfactants to humic substances

    NARCIS (Netherlands)

    Ishiguro, M.; Tan, W.; Koopal, L.K.

    2007-01-01

    Commercial surfactants are introduced into the environment either through waste products or site-specific contamination. The amphiphilic nature of both surfactants and humic substances (HS) leads to their mutual attraction especially when surfactant and HS are oppositely charged. Binding of the

  5. Surfactant adsorption to soil components and soils

    NARCIS (Netherlands)

    Ishiguro, Munehide; Koopal, Luuk K.

    2016-01-01

    Soils are complex and widely varying mixtures of organic matter and inorganic materials; adsorption of surfactants to soils is therefore related to the soil composition. We first discuss the properties of surfactants, including the critical micelle concentration (CMC) and surfactant adsorption on

  6. A soft and conductive PDMS-PEG block copolymer as a compliant electrode for dielectric elastomers

    DEFF Research Database (Denmark)

    A Razak, Aliff Hisyam; Szabo, Peter; Skov, Anne Ladegaard

    -methyl pyrrolidinone) with 1 wt% of surfactant (Triton X-100). The dispersion of MWCNTs in PDMS-PEG systemis shown in figure 2 where MWCNTs (dark areas) are well-distributed in the system indicating an acceptable dispersional though some big clusters appear in the optical microscope image. The conductivity of 4 phr...

  7. An Evaluation of Emulsions in Wear-Metal-in-Oil Analyses | Fischer ...

    African Journals Online (AJOL)

    The oil samples were treated with acid and emulsified in water (1% w/w) using tetralin as a solvent and Triton X-100 as a surfactant. The performance characteristics (detection limits, accuracy, precision and spike recovery) of the emulsion methodology were evaluated. The calibration for the emulsion method compared ...

  8. Experimental investigation of thermophysical properties, entropy generation and convective heat transfer for a nitrogen-doped graphene nanofluid in a laminar flow regime

    DEFF Research Database (Denmark)

    Mehrali, Mohammad; Sadeghinezhad, Emad; Rosen, Marc A.

    2016-01-01

    Nitrogen-doped graphene (NDG) nanofluids are prepared using a two-step method in an aqueous solution of 0.025. wt% Triton X-100 as a surfactant with various nanosheets at several concentrations (0.01, 0.02, 0.04, 0.06. wt%). The results are reported of experiments on the thermal conductivity...

  9. Untitled

    African Journals Online (AJOL)

    The bulky ferrocyphen [Dicyano-bis-(1, 10-. Phenanthroline) Iron lll complex, with significant hydrophobic character and the three surfactants, SDS. (sodium dodecylsulphate), CTAB. (cetyltrimethylammonium bromide) and Triton X-. 100 were especially selected for their overall varying hydrophobicity. Since binding in some ...

  10. Persurf, a new method to improve surfactant delivery: a study in surfactant depleted rats.

    Directory of Open Access Journals (Sweden)

    Wolfram Burkhardt

    Full Text Available PURPOSE: Exogenous surfactant is not very effective in adults with ARDS, since surfactant does not reach atelectatic alveoli. Perfluorocarbons (PFC can recruit atelectatic areas but do not replace impaired endogenous surfactant. A surfactant-PFC-mixture could combine benefits of both therapies. The aim of the proof-of-principal-study was to produce a PFC-in-surfactant emulsion (Persurf and to test in surfactant depleted Wistar rats whether Persurf achieves I. a more homogenous pulmonary distribution and II. a more homogenous recruitment of alveoli when compared with surfactant or PFC alone. METHODS: Three different PFC were mixed with surfactant and phospholipid concentration in the emulsion was measured. After surfactant depletion, animals either received 30 ml/kg of PF5080, 100 mg/kg of stained (green dye Curosurf™ or 30 ml/kg of Persurf. Lungs were fixated after 1 hour of ventilation and alveolar aeration and surfactant distribution was estimated by a stereological approach. RESULTS: Persurf contained 3 mg/ml phospholipids and was stable for more than 48 hours. Persurf-administration improved oxygenation. Histological evaluation revealed a more homogenous surfactant distribution and alveolar inflation when compared with surfactant treated animals. CONCLUSIONS: In surfactant depleted rats administration of PFC-in-surfactant emulsion leads to a more homogenous distribution and aeration of the lung than surfactant alone.

  11. Protective effect of Tritone (Livosone) on oxidative DNA damage and its hepatoprotective potential against various hepatotoxic agent in wistar rats.

    Science.gov (United States)

    Medhekar, Sheetal Kashinath; Jadhav, Tejas Pandurang; Sasane, Vishal Sadashiv; Shende, Vikas Suresh; Aloorkar, Nagesh Hanmantrao; Chincholkar, Anjali Baburao; Soman, Girish Sudhakar; Kulkarni, Ajit Shankarrao

    2017-03-02

    To evaluate antioxidant activity, DNA damage inhibition and hepatoprotecitve potential of polyherbal formulation Tritone (Livosone). In vitro antioxidant activity of Tritone formulation was performed by using DPPH assay. Hepatoprotecitve potential of Tritone was evaluated against various hepatotoxic agents including Paracetamol (2g/kg b. wt p.o. single dose on 15th day), Galactosamine (400mg/kg b. wt. i.p. single dose on 8th day) and Alcohol (30% p.o.1ml/100g of rat for 15days). Tritone formulation at the doses of (40.5, 81 and 162mg/kg) and standard silymarin (100mg/kg) and Liv52 (270mg/kg) were administered p.o. The hepatoprotective assessment was done by estimating biochemical parameters: SGOT, SGPT, ALP and Total Bilirubin total protein and ChE levels. Additionally histopathological and DNA fragmentation study of Tritone was also performed. Administration of hepatotoxins (paracetamol, D-GaiN and alcohol) in experimental animals showed significant biochemical, histological deterioration and DNA fragmentation. Pretreatment with Tritone (Livosone) shows significant reduction in serum SGOT, SGPT, ALP and total bilirubin levels and shows significant elevation in total protein and cholinesterase (ChE) levels compared to groups treated with hepatotoxic agents. Histopathological observations of rat liver pretreated with Tritone (Livosone) shows significant protection against hepatic damage. Inhibition of DNA fragmentation by Tritone indicates protective effect of formulation on liver at molecular level. Finally all the results were compared with standard drugs Silymarin and Liv52. Correlation of antioxidant activity, biochemical results, histopathological changes and inhibition of DNA damage after treatment with Tritone shows maximum hepatoprotective potential at dose 81mg/kg and 162mg/kg. Copyright © 2016 Elsevier GmbH. All rights reserved.

  12. Surfactant gene polymorphisms and interstitial lung diseases

    Directory of Open Access Journals (Sweden)

    Pantelidis Panagiotis

    2001-11-01

    Full Text Available Abstract Pulmonary surfactant is a complex mixture of phospholipids and proteins, which is present in the alveolar lining fluid and is essential for normal lung function. Alterations in surfactant composition have been reported in several interstitial lung diseases (ILDs. Furthermore, a mutation in the surfactant protein C gene that results in complete absence of the protein has been shown to be associated with familial ILD. The role of surfactant in lung disease is therefore drawing increasing attention following the elucidation of the genetic basis underlying its surface expression and the proof of surfactant abnormalities in ILD.

  13. Calcium-tolerant anionic surfactants

    NARCIS (Netherlands)

    Kooreman, Alexander

    1995-01-01

    One of the problems of applying anionic surfactants in, for example, laundry detergents is the precipitation of calcium salts. Much effort has been directed towards avoiding precipitation. There are at least three ways for tackling the problem. The first involves the use of a large quantity of

  14. Surfactant -- Where Are We in 2003?

    Directory of Open Access Journals (Sweden)

    JF Lewis

    2004-01-01

    Full Text Available Surfactant research has progressed over the past several years to the extent that exogenous surfactant administration in patients with the acute respiratory distress syndrome (ARDS is now being evaluated. Unfortunately, clinical responses have been variable, and we now need to take a look at how surfactant is altered in this disease so that more effective treatment strategies can be developed. This review briefly discusses the biophysical and host defense properties of surfactant, the impact of mechanical ventilation (MV on the endogenous surfactant system and the most recent clinical data involving exogenous surfactant administration in patients with ARDS. Discussions regarding future directions of surfactant research both in ARDS and diseases other than acute lung injury are included.

  15. Tritons and tritides as the solute and diffusing species in ceramic tritium breeders

    International Nuclear Information System (INIS)

    Fischer, A.K.; Johnson, C.E.

    1987-01-01

    Intragranular diffusion of tritium is an inherent participant in the process of releasing tritium from lithium-containing ceramics that are used to breed tritium in a fusion reactor. The nature of this transport is reviewed in terms of the understanding established for the mechanism of hydrogen migration in other oxides, namely, that the diffusing species is the proton and that it moves from oxide ion to oxide ion, thereby giving rise to apparent hydroxide migration. Analogously, the triton, transiently bonded to successive oxides and forming successive tritoxides, is taken to be the dominant migrating species in ceramic breeders. In addition, tritide becomes a significant participant at low oxygen activity. The relationship of tritons and tritides as the migrating species to the observed release of both reduced and oxidized forms can be understood in terms of the thermodynamic conditions that prevail. Mechanisms exist that can be proposed to rationalize the participation of these species

  16. Present state and chemical evolution of the atmospheres of Titan, Triton, and Pluto

    International Nuclear Information System (INIS)

    Lunine, J.I.; Atreya, S.K.; Pollack, J.B.

    1989-01-01

    An evaluation is made of the current understanding of the atmospheres of Titan, Triton, and Pluto, as well as of theoretical models for their origin and evolution. All three atmospheres contain methane, while Titan, and probably Triton, have nitrogen. The primary driver in the evolution of the Titan atmosphere has been the irreversible photolysis of methane. If a surface reservoir of liquid methane exists to resupply the atmosphere, it is subject to enrichment in ethane due to the long-term photolysis of methane. The key issue in the origin and early evolution of Titan's atmosphere is the source of molecular nitrogen; two schemes for the conversion of ammonia to nitrogen have been considered

  17. Adsorption of dimeric surfactants in lamellar silicates

    Energy Technology Data Exchange (ETDEWEB)

    Balcerzak, Mateusz; Pietralik, Zuzanna [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland); Domka, Ludwik [Department of Metalorganic Chemistry, Faculty of Chemistry, A. Mickiewicz University, Grunwaldzka 6, 60-780 Poznań (Poland); Skrzypczak, Andrzej [Institute of Chemical Technology, Poznań University of Technology, Berdychowo 4, 60-965 Poznań (Poland); Kozak, Maciej, E-mail: mkozak@amu.edu.pl [Department of Macromolecular Physics, Faculty of Physics, A. Mickiewicz University, Umultowska 85, 61-614 Poznań (Poland)

    2015-12-01

    Highlights: • The intercalation of dimeric surfactants changed the morphology of MMT samples. • XRD indicated structures formed by surfactant molecules in interlayer space. • The four-step thermal decomposition of dimeric surfactant, confirms intercalation. - Abstract: The adsorption of different types of cationic surfactants in lamellar silicates changes their surface character from hydrophilic to hydrophobic. This study was undertaken to obtain lamellar silicates modified by a series of novel dimeric (gemini) surfactants of different length alkyl chains and to characterise these organophilised materials. Synthetic sodium montmorillonite SOMASIF® ME 100 (M) and enriched bentonite of natural origin (Nanoclay – hydrophilic bentonite®) were organophilised with dimeric (gemini) surfactants (1,1′-(1,4-butanediyl)bis(alkoxymethyl)imidazolium dichlorides). As a result of surfactant molecule adsorption in interlamellar space, the d-spacing (d{sub 001}) increased from 0.97 nm (for the anhydrous structure) to 2.04 nm. A Fourier transform infrared spectroscopy (FTIR) analysis of the modified systems reveals bands assigned to the stretching vibrations of the CH{sub 2} and CH{sub 3} groups and the scissoring vibrations of the NH group from the structure of the dimeric surfactants. Thermogravimetric (TG) and derivative thermogravimetric (DTG) studies imply a four-stage process of surfactant decomposition. Scanning electron microscopy (SEM) images provide information on the influence of dimeric surfactant intercalation into the silicate structures. Particles of the modified systems show a tendency toward the formation of irregularly shaped agglomerates.

  18. A conservative SPH method for surfactant dynamics

    Science.gov (United States)

    Adami, S.; Hu, X. Y.; Adams, N. A.

    2010-03-01

    In this paper, a Lagrangian particle method is proposed for the simulation of multiphase flows with surfactant. The model is based on the multiphase smoothed particle hydrodynamics (SPH) framework of Hu and Adams (2006) [1]. Surface-active agents (surfactants) are incorporated into our method by a scalar quantity describing the local concentration of molecules in the bulk phase and on the interface. The surfactant dynamics are written in conservative form, thus global mass of surfactant is conserved exactly. The transport model of the surfactant accounts for advection and diffusion. Within our method, we can simulate insoluble surfactant on an arbitrary interface geometry as well as interfacial transport such as adsorption or desorption. The flow-field dynamics and the surfactant dynamics are coupled through a constitutive equation, which relates the local surfactant concentration to the local surface-tension coefficient. Hence, the surface-tension model includes capillary and Marangoni-forces. The present numerical method is validated by comparison with analytic solutions for diffusion and for surfactant dynamics. More complex simulations of an oscillating bubble, the bubble deformation in a shear flow, and of a Marangoni-force driven bubble show the capabilities of our method to simulate interfacial flows with surfactants.

  19. Solid methane on Triton and Pluto - 3- to 4-micron spectrophotometry

    Science.gov (United States)

    Spencer, John R.; Buie, Marc W.; Bjoraker, Gordon L.

    1990-01-01

    Methane has been identified in the Pluto/Charon system on the basis of absorption features in the reflectance spectrum at 1.5 and 2.3 microns; attention is presently given to observations of a 3.25 micron-centered deep absorption feature in Triton and Pluto/Charon system reflectance spectra. This absorption may indicate the presence of solid methane, constituting either the dominant surface species or a mixture with a highly transparent substance, such as N2 frost.

  20. A rare case of retroperitoneal malignant triton tumor invading renal vein and small intestine

    Directory of Open Access Journals (Sweden)

    Mijović Žaklina

    2013-01-01

    Full Text Available Introduction. Malignant Triton tumor is a very rare malignant peripheral nerve sheath tumor with rhabdomyosarcomatous differentiation. Most of those tumors occur in patients with von Recklinghausen’s disease or as a late complication of irradiation and commonly seen in the head, neck, extremities and trunk. Case report. We reported retroperitoneal malignant Triton tumor in a 57-year-old female patient. Skin lesions were not present, and there was no family history of neurofibromatosis or previous irradiation. The presented case is one of a few recorded in the specialized literature that occurs in the retroperitoneal space in sporadic form. In this case, tumor consisted of a multilobular mass was in close relation with the abdominal aorta and inferior vena cava and involved the renal vein with gross invasion of the small intestine. The patient underwent total resection of the tumor and left nefrectomy was performed. The small intestine 10 cm in length was also resected and end-to-end anastomosis was conducted. The postoperative course was uneventful and the patient was discharged from the hospital ten days after the surgery. Conclusion. Diagnostically, it is crucial to recognize this uncommon histological variant because malignant Triton tumor has a worse prognosis than classic malignant peripheral nerve sheath tumor does. The use of the immunohistochemistry is essential in making the correct diagnosis. Only appropriate pathological evaluation supported by immunostaining with S-100 protein and desmin confirmed the diagnosis. Aggressive surgical management treatment improves the prognosis of such cases with adjuvant radiotherapy.

  1. Spectral-motion aftereffects and the tritone paradox among Canadian subjects.

    Science.gov (United States)

    Dawe, L A; Platt, J R; Welsh, E

    1998-02-01

    The effect of spectral motion on the tritone paradox was investigated by pretesting subjects residing in southwestern Ontario, Canada, on the tritone task, presenting them with a continuous ascending or descending chromatic scale created using Shepard tones, and then retesting them on the tritone task. Results indicated a negative-motion aftereffect that affected the orientation of the pitch class circle. Differential effects of perceived pitch height on the lower portion of the pitch class circle and of adaptation on the upper portion of the pitch class circle were found in the pre- and postadaptation data, respectively. The implications of this dissociation are discussed. In addition, since our subjects lived relatively close to the U.S. border, the experimental pretests allowed us to examine the hypothesis that a canonical American pitch template similar to that found among "Californian" subjects (Deutsch, 1991) is propagated by linguistic influences of media such as television and radio (Ragozzine & Deutsch, 1994). A survey of our subjects indicated that overall, the majority of time engaged in listening to the radio and watching television or movies was spent with American sources. Despite this, and despite the fact that subjects had widely varying language and cultural backgrounds, a tight distribution of peak-pitch classes was found that is indicative of a "British" pitch template (Deutsch, 1991) for every subject tested.

  2. A study on the treatment of radioactive slurry liquid waste

    International Nuclear Information System (INIS)

    Jeong, Gyeong Hwan; Chung, U. S.; Baik, S. T.; Park, S. K.; Moon, J.S.; Jung, K.J.

    1998-12-01

    The influence of anionic flocculants on the dewatering of radioactive slurries has been investigated in a laboratory-scale vacuum filtration unit. Simultaneously the influence of certain surfactants on the dewatering of radioactive slurries with anionic flocculants has also been investigated. Test results show that the flocculated filter cake generally contains higher residual water than the unflocculated cake. The non-ionic surfactant Triton X-100 was effective in reducing the moisture content of the cake

  3. Surfactants in tribology, v.3

    CERN Document Server

    Biresaw, Girma

    2013-01-01

    The manufacture and use of almost every consumer and industrial product rely on application of advanced knowledge in surface science and tribology. These two disciplines are of critical importance in major economic sectors, such as mining, agriculture, manufacturing (including metals, plastics, wood, computers, MEMS, NEMS, appliances), construction, transportation, and medical instruments, transplants, and diagnostic devices. An up-to-date reference with contributions by experts in surface science and tribology, Surfactants in Tribology, Volume 3 discusses some of the underlying tribological a

  4. Enhanced Oil Recovery with Surfactant Flooding

    DEFF Research Database (Denmark)

    Sandersen, Sara Bülow

    Enhanced oil recovery (EOR) is being increasingly applied in the oil industry and several different technologies have emerged during, the last decades in order to optimize oil recovery after conventional recovery methods have been applied. Surfactant flooding is an EOR technique in which the phase...... behavior inside the reservoir can be manipulated by the injection of surfactants and co-surfactants, creating advantageous conditions in order to mobilize trapped oil. Correctly designed surfactant systems together with the crude oil can create microemulsions at the interface between crude oil and water......, thus reducing the interfacial tension (IFT) to ultra low (0.001 mN/m), which consequently will mobilize the residual oil and result in improved oil recovery. This EOR technology is, however, made challenging by a number of factors, such as the adsorption of surfactant and co-surfactant to the rock...

  5. Acute Pathophysiological Effects of Intratracheal Instillation of Budesonide and Exogenous Surfactant in a Neonatal Surfactant-depleted Piglet Model

    Directory of Open Access Journals (Sweden)

    Chia-Feng Yang

    2010-08-01

    Conclusions: Intratracheal instillation of surfactant or surfactant plus budesonide can improve oxygenation and pulmonary histologic outcome in neonatal surfactant-depleted lungs. The additional use of budesonide does not disturb the function of the exogenous surfactant. Intratracheal administration of a corticosteroid combined with surfactant may be an effective method for alleviating local pulmonary inflammation in severe RDS.

  6. Cationic versus anionic surfactant in tuning the structure and interaction of nanoparticle, protein, and surfactant complexes.

    Science.gov (United States)

    Mehan, Sumit; Aswal, Vinod K; Kohlbrecher, Joachim

    2014-08-26

    The structure and interaction in complexes of anionic Ludox HS40 silica nanoparticle, anionic bovine serum albumin (BSA) protein, and cationic dodecyl trimethylammonium bromide (DTAB) surfactant have been studied using small-angle neutron scattering (SANS). The results are compared with similar complexes having anionic sodium dodecyl sulfate (SDS) surfactant (Mehan, S; Chinchalikar, A. J.; Kumar, S.; Aswal, V. K.; Schweins, R. Langmuir 2013, 29, 11290). In both cases (DTAB and SDS), the structure in nanoparticle-protein-surfactant complexes is predominantly determined by the interactions of the individual two-component systems. The nanoparticle-surfactant (mediated through protein-surfactant complex) and protein-surfactant interactions for DTAB, but nanoparticle-protein (mediated through protein-surfactant complex) and protein-surfactant interactions for SDS, are found to be responsible for the resultant structure of nanoparticle-protein-surfactant complexes. Irrespective of the charge on the surfactant, the cooperative binding of surfactant with protein leads to micellelike clusters of surfactant formed along the unfolded protein chain. The adsorption of these protein-surfactant complexes for DTAB on oppositely charged nanoparticles gives rise to the protein-surfactant complex-mediated aggregation of nanoparticles (similar to that of DTAB surfactant). It is unlike that of depletion-induced aggregation of nanoparticles with nonadsorption of protein-surfactant complexes for SDS in similarly charged nanoparticle systems (similar to that of protein alone). The modifications in nanoparticle aggregation as well as unfolding of protein in these systems as compared to the corresponding two-component systems have also been examined by selectively contrast matching the constituents.

  7. Surfactant-enhanced cellulose nanocrystal Pickering emulsions.

    Science.gov (United States)

    Hu, Zhen; Ballinger, Sarah; Pelton, Robert; Cranston, Emily D

    2015-02-01

    The effect of surfactants on the properties of Pickering emulsions stabilized by cellulose nanocrystals (CNCs) was investigated. Electrophoretic mobility, interfacial tension, confocal microscopy and three-phase contact angle measurements were used to elucidate the interactions between anionic CNCs and cationic alkyl ammonium surfactants didecyldimethylammonium bromide (DMAB) and cetyltrimethylammonium bromide (CTAB). Both surfactants were found to adsorb onto CNCs with concentration-dependent morphology. At low concentrations, individual surfactant molecules adsorbed with alkyl tails pointing outward leading to hydrophobic CNCs. At higher concentrations, above the surfactant's apparent critical micelle concentration, surfactant aggregate morphologies on CNCs were inferred and the hydrophobicity of CNCs decreased. DMAB, which has two alkyl tails, rendered the CNCs more hydrophobic than CTAB which has only a single alkyl tail, at all surfactant concentrations. The change in CNC wettability from surfactant adsorption was directly linked to emulsion properties; adding surfactant increased the emulsion stability, decreased the droplet size, and controlled the internal phase of CNC Pickering emulsions. More specifically, a double transitional phase inversion, from oil-in-water to water-in-oil and back to oil-in-water, was observed for emulsions with CNCs and increasing amounts of DMAB (the more hydrophobic surfactant). With CNCs and CTAB, no phase inversion was induced. This work represents the first report of CNC Pickering emulsions with surfactants as well as the first CNC Pickering emulsions that can be phase inverted. The ability to surface modify CNCs in situ and tailor emulsions by adding surfactants may extend the potential of CNCs to new liquid formulations and extruded/spray-dried materials. Copyright © 2014 Elsevier Inc. All rights reserved.

  8. Interactions between surfactants and hydrolytic enzymes.

    Science.gov (United States)

    Holmberg, Krister

    2017-12-05

    Hydrolytic enzymes are combined with surfactants in many types of formulations, for instance detergents and personal care products. If the surfactant interacts with the enzyme there may be conformational changes that eventually lead to loss of the enzymatic activity. From a practical point of view it is important to understand the nature and magnitude of these interactions. After an introduction of the topic the review briefly discusses enzyme catalyzed reactions where surfactants are substrates for the enzyme. The rest of the review relates to associations between surfactants and hydrolytic enzymes without the surfactant being a substrate in the reaction. A discussion about general principles for such interactions is followed by a survey of the relevant literature related to four important types of hydrolytic enzymes: lipases, proteases, amylases and cellulases. It is shown in the review that the effect exerted by the surfactant differs between the different types of enzymes; it is therefore difficult to make general statements about which surfactants are most detrimental to the activity of hydrolytic enzymes. However, as a general rule nonionic surfactants can be regarded as more benign to an enzyme than anionic and cationic surfactants. This difference can be ascribed to the difference in binding mode. Whereas a nonionic surfactant only binds to the enzyme through hydrophobic interactions, an ionic surfactant can bind by a combination of electrostatic attraction and hydrophobic interaction. This latter type of binding can be strong and lead to conformational changes already at very low surfactant concentration, often far below its critical micelle concentration. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Phase transitions in surfactant monolayers

    International Nuclear Information System (INIS)

    Casson, B.D.

    1998-01-01

    Two-dimensional phase transitions have been studied in surfactant monolayers at the air/water interface by sum-frequency spectroscopy and ellipsometry. In equilibrium monolayers of medium-chain alcohols C n H 2n+1 OH (n = 9-14) a transition from a two-dimensional crystalline phase to a liquid was observed at temperatures above the bulk melting point. The small population of gauche defects in the solid phase increased only slightly at the phase transition. A model of the hydrocarbon chains as freely rotating rigid rods allowed the area per molecule and chain tilt in the liquid phase to be determined. The area per molecule, chain tilt and density of the liquid phase all increased with increasing chain length, but for each chain length the density was higher than in a bulk liquid hydrocarbon. In a monolayer of decanol adsorbed at the air/water interface a transition from a two-dimensional liquid to a gas was observed. A clear discontinuity in the coefficient of ellipticity as a function of temperature showed that the transition is first-order. This result suggests that liquid-gas phase transitions in surfactant monolayers may be more widespread than once thought. A solid-liquid phase transition has also been studied in mixed monolayers of dodecanol with an anionic surfactant (sodium dodecyl sulphate) and with a homologous series of cationic surfactants (alkyltrimethylammonium bromides: C n TABs, n = 12, 14, 16). The composition and structure of the mixed monolayers was studied above and below the phase transition. At low temperatures the mixed monolayers were as densely packed as a monolayer of pure dodecanol in its solid phase. At a fixed temperature the monolayers under-went a first-order phase transition to form a phase that was less dense and more conformationally disordered. The proportion of ionic surfactant in the mixed monolayer was greatest in the high temperature phase. As the chain length of the C n TAB increased the number of conformational defects

  10. Significant effect of surfactant micelles on pH dependent fluorescent off-on-off behavior of Salicylaldehyde-2,4-Dinitrophenylhydrazone

    Energy Technology Data Exchange (ETDEWEB)

    Goswami, Priyanka [Department of Chemistry, Gauhati University, Guwahati 781 014 (India); Das, Diganta K., E-mail: digkdas@yahoo.co [Department of Chemistry, Gauhati University, Guwahati 781 014 (India)

    2011-04-15

    The fluorescence response to pH of 2,4 dinitrophenolhydrazone in 1:1 CH{sub 3}OH:H{sub 2}O and micellar mediums-negatively charged sodium dodecylsulphate (SDS), positively charged cetyltrimethyl ammonium bromide (CTAB) and neutral Triton X-100 (TX-100), is reported. At pH 4.0 the fluorescence of the molecule can be switched 'on' by selecting CTAB as the solvent. At pH 6.0 if the medium is TX-100 the fluorescence is 'off', but remains 'on' for the other three solvents. At pH 8.0, fluorescence is 'on' in the solvents except CTAB. SDS and TX-100 switch the fluorescence 'on' at pH 13.0 but for the other two solvents the fluorescence is 'off'. - Research highlights: The fluorescence response to pH of Salicylaldehyde-2,4 Dinitrophenolhydrazone in 1:1 CH{sub 3}OH:H{sub 2}O and in positively charged cetyltrimethyl ammonium bromide (CTAB) micellar medium shows 'off-on-off' behavior. In negatively charged sodium dodecylsulphate (SDS) the response of fluorescence of Salicylaldehyde-2,4 Dinitrophenolhydrazone to pH is 'off-on-on' type while in neutral Triton X-100 it is 'off-on-1/2on' type. At a given pH, fluorescence of 2,4 dinitrophenolhydrazone can be made 'on' or 'off' by selecting an appropriate pH.

  11. Surfactant nebulisation : lung function, surfactant distribution and pulmonary blood flow distribution in lung lavaged rabbits

    NARCIS (Netherlands)

    Dijk, Peter H.; Heikamp, A; Bambang Oetomo, Sidarto

    1997-01-01

    Objective: Surfactant nebulisation is a promising alternative to surfactant instillation in newborns with the respiratory distress syndrome. Although less surfactant is deposited in the lung, it improves gas exchange, probably due to a superior distribution. We hypothesize that a more uniform

  12. Solubilization of Hydrophobic Dyes in Surfactant Solutions

    Directory of Open Access Journals (Sweden)

    Ali Reza Tehrani-Bagha

    2013-02-01

    Full Text Available In this paper, the use of surfactants for solubilization of hydrophobic organic dyes (mainly solvent and disperse dyes has been reviewed. The effect of parameters such as the chemical structures of the surfactant and the dye, addition of salt and of polyelectrolytes, pH, and temperature on dye solubilization has been discussed. Surfactant self-assemble into micelles in aqueous solution and below the concentration where this occurs—the critical micelle concentration (CMC—there is no solubilization. Above the CMC, the amount of solubilized dye increases linearly with the increase in surfactant concentration. It is demonstrated that different surfactants work best for different dyes. In general, nonionic surfactants have higher solubilization power than anionic and cationic surfactants. It is likely that the reason for the good performance of nonionic surfactants is that they allow dyes to be accommodated not only in the inner, hydrocarbon part of the micelle but also in the headgroup shell. It is demonstrated that the location of a dye in a surfactant micelle can be assessed from the absorption spectrum of the dye-containing micellar solution.

  13. Remediation using trace element humate surfactant

    Science.gov (United States)

    Riddle, Catherine Lynn; Taylor, Steven Cheney; Bruhn, Debra Fox

    2016-08-30

    A method of remediation at a remediation site having one or more undesirable conditions in which one or more soil characteristics, preferably soil pH and/or elemental concentrations, are measured at a remediation site. A trace element humate surfactant composition is prepared comprising a humate solution, element solution and at least one surfactant. The prepared trace element humate surfactant composition is then dispensed onto the remediation site whereby the trace element humate surfactant composition will reduce the amount of undesirable compounds by promoting growth of native species activity. By promoting native species activity, remediation occurs quickly and environmental impact is minimal.

  14. Solvent extraction of lanthanoid and yttrium ions with poly(oxyethylene)alkylphenylether

    International Nuclear Information System (INIS)

    Yoshida, Isao; Takeshita, Ryo-ichi; Ueno, Keihei; Takagi, Makoto.

    1986-01-01

    Solvent extraction of lanthanoid and yttrium ions(M 3+ ) was investigated in a water-dichloroethane system using poly(oxyethylene)-type nonionic surfactants such as Triton X-100 and Triton X-405(L) and picrate ion(A - ) as extraction agent and pairing anion, respectively. The result of extraction studies at various extraction agent concentrations and at various picrate ion concentrations, suggested that the composition of the extracted species was MLA 3 . Among the lanthanoid ions investigated, the ions such as Nd 3+ , Sm 3+ , Eu 3+ , and Gd 3+ gave relatively larger distribution ratios than the other lanthanoid ions, while the yttrium ion was the least extractable among the metal ions investigated. The distribution ratio with extraction agent Triton X-405 was about ten times larger than those with Triton X-100. (author)

  15. Hemolysis by surfactants--A review.

    Science.gov (United States)

    Manaargadoo-Catin, Magalie; Ali-Cherif, Anaïs; Pougnas, Jean-Luc; Perrin, Catherine

    2016-02-01

    An overview of the use of surfactants for erythrocyte lysis and their cell membrane action mechanisms is given. Erythrocyte membrane characteristics and its association with the cell cytoskeleton are presented in order to complete understanding of the erythrocyte membrane distortion. Cell homeostasis disturbances caused by surfactants might induce changes starting from shape modification to cell lysis. Two main mechanisms are hypothesized in literature which are osmotic lysis and lysis by solubilization even if the boundary between them is not clearly defined. Another specific mechanism based on the formation of membrane pores is suggested in the particular case of saponins. The lytic potency of a surfactant is related to its affinity for the membrane and the modification of the lipid membrane curvature. This is to be related to the surfactant shape defined by its hydrophobic and hydrophilic moieties but also by experimental conditions. As a consequence, prediction of the hemolytic potency of a given surfactant is challenging. Several studies are focused on the relation between surfactant erythrolytic potency and their physico-chemical parameters such as the critical micellar concentration (CMC), the hydrophile-lipophile balance (HLB), the surfactant membrane/water partition coefficient (K) or the packing parameter (P). The CMC is one of the most important factors considered even if a lytic activity cut-off effect points out that the only consideration of CMC not enough predictive. The relation K.CMC must be considered in addition to the CMC to predict the surfactant lytic capacity within the same family of non ionic surfactant. Those surfactant structure/lytic activity studies demonstrate the requirement to take into account a combination of physico-chemical parameters to understand and foresee surfactant lytic potency. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. DILUTE SURFACTANT METHODS FOR CARBONATE FORMATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Kishore K. Mohanty

    2003-07-01

    There are many carbonate reservoirs in US (and the world) with light oil and fracture pressure below its minimum miscibility pressure (or reservoir may be naturally fractured). Many carbonate reservoirs are naturally fractured. Waterflooding is effective in fractured reservoirs, if the formation is water-wet. Many fractured carbonate reservoirs, however, are mixed-wet and recoveries with conventional methods are low (less than 10%). Thermal and miscible tertiary recovery techniques are not effective in these reservoirs. Surfactant flooding (or huff-n-puff) is the only hope, yet it was developed for sandstone reservoirs in the past. The goal of this research is to evaluate dilute (hence relatively inexpensive) surfactant methods for carbonate formations and identify conditions under which they can be effective. We have conducted adsorption, phase behavior, interfacial tension (IFT) and wettability studies. Addition of Na{sub 2}CO{sub 3} decreases IFT with a minimum at about 0.2 M. Addition of surfactant decreases IFT further. In the absence of surfactant the minerals are oil-wet after aging with crude oil. Addition of surfactant solution decreases the contact angle to intermediate-wet for many surfactants and water-wet for one surfactant. Addition of Na{sub 2}CO{sub 3} decreases anionic surfactant adsorption on calcite surface. Plans for the next quarter include conducting core adsorption, phase behavior, wettability and mobilization studies.

  17. of surfactant replacement therapy at Johannesburg Hospital ...

    African Journals Online (AJOL)

    Objective. To assess the impact of surfactant replacement therapy (SRl) on the outcome of hyaline membrane disease (HMD) and to assess the cost implications of a policy of selective administration of artificial surfactant. Design. The short-term outcome of 103 newborns ventilated for HMD (61 selected for SRT according to ...

  18. Surfactant protein D in newborn infants

    DEFF Research Database (Denmark)

    Dahl, Marianne; Juvonen, Pekka Olavi; Holmskov, Uffe

    2005-01-01

    Surfactant protein D (SP-D) is a collectin that plays an important role in the innate immune system. The role of SP-D in the metabolism of surfactant is as yet quite unclear. The aims of this study were to establish normal values of SP-D in the umbilical cord blood and capillary blood of mature...

  19. Surfactant effects on soil aggregate tensile strength

    Science.gov (United States)

    Little is known regarding a soil aggregate's tensile strength response to surfactants that may be applied to alleviate soil water repellency. Two laboratory investigations were performed to determine surfactant effects on the tensile strength of 1) Ap horizons of nine wettable, agricultural soils co...

  20. Measuring surfactant concentration in plating solutions

    Science.gov (United States)

    Bonivert, William D.; Farmer, Joseph C.; Hachman, John T.

    1989-01-01

    An arrangement for measuring the concentration of surfactants in a electrolyte containing metal ions includes applying a DC bias voltage and a modulated voltage to a counter electrode. The phase angle between the modulated voltage and the current response to the modulated voltage at a working electrode is correlated to the surfactant concentration.

  1. Surfactant Adsorption: A Revised Physical Chemistry Lab

    Science.gov (United States)

    Bresler, Marc R.; Hagen, John P.

    2008-01-01

    Many physical chemistry lab courses include an experiment in which students measure surface tension as a function of surfactant concentration. In the traditional experiment, the data are fit to the Gibbs isotherm to determine the molar area for the surfactant, and the critical micelle concentration is used to calculate the Gibbs energy of micelle…

  2. Surfactants and submicron sea spray generation

    NARCIS (Netherlands)

    Sellegri, K.; O'Dowd, C.D.; Yoon, Y.J.; Jennings, S.G.; Leeuw, G. de

    2006-01-01

    Laboratory experiments have been carried out to elucidate the role of surfactants on the primary marine aerosol production of submicron marine aerosols. A synthetic surfactant SDS was used in conjunction with artificially generated seawater, and the resultant bubble-mediated aerosol produced was

  3. Hypolipidemic action of chrysin on Triton WR-1339-induced hyperlipidemia in female C57BL/6 mice

    Directory of Open Access Journals (Sweden)

    Micheli Stéfani Zarzecki

    2014-01-01

    Full Text Available Chrysin (5,7-dihydroxyflavone is a flavonoid, natural component of traditional medicinal herbs, present in honey, propolis and many plant extracts. The objective of this study was to investigate the hypolipidemic properties of chrysin on Triton WR-1339-induced hyperlipidemia in female C57BL/6 mice. Triton WR-1339 was administered intraperitoneally (400 mg/kg to overnight-fasted mice to develop acute hyperlipidemia. Chrysin was administered orally (10 mg/kg 30 min before Triton WR-1339. At 24 h after Triton WR-1339 injection, blood samples were collected to measure plasma lipid levels. The hepatic thiobarbituric acid reactive substances (TBARS, carbonyl content, non-protein sulfhydryl (NPSH and ascorbic acid (AA levels, as well as catalase (CAT and superoxide dismutase (SOD activity were recorded. Chrysin administration significantly decreased total cholesterol levels. In addition, it partially decreased non-high density lipoprotein-cholesterol and triglycerides levels in plasma of hyperlipidaemic mice. In addition chrysin administration prevented the increase on TBARS levels and prevented the decrease in SOD activity induced by Triton WR-1339. These findings indicated that chrysin was able to decrease plasma lipids concentration and that its antioxidant properties was, at least in part, involved in the hypolipidaemic action of chrysin.

  4. Origin and Evolution of Nitrogen on Titan, Enceladus, Triton, and Pluto

    Science.gov (United States)

    Atreya, S. K.; Niemann, H. B.; Mahaffy, P. R.; Owen, T. C.

    2007-01-01

    Nitrogen, together with carbon, hydrogen, oxygen, phosphorus and sulfur (CHNOPS), plays a central role in life as we know it. Indeed, molecular nitrogen is the most abundant component of the terrestrial atmosphere, and second only to carbon dioxide on Mars and Venus. The Voyager and Cassini-Huygens observations show that copious nitrogen is present on Titan also, comprising some 95% by volume of this moon's 1500 millibar atmosphere. After water vapor, it may be the most abundant (4%) of the gases around tiny Enceladus, as revealed by the recent Cassini observations. A thin nitrogen atmosphere is found even on the coldest of the solar system bodies, Triton and Pluto. The available evidence on nitrogen isotopes and the heavy noble gases suggests that Titan acquired its nitrogen largely in the form of ammonia. Subsequent chemical evolution, beginning with the photolysis of NH3 on primordial Titan, led to the nitrogen atmosphere we see on Titan today. This is also the scenario for the origin of nitrogen on the terrestrial planets. Contrary to Titan, the colder outer solar system objects, Triton and Pluto, neither had the luxury of receiving much arnmonia in the first place, nor of photolyzing whatever little ammonia they did receive in the planetesimals that formed them. On the other hand, it is plausible the planetesimals were capable of trapping and delivering molecular nitrogen directly to Triton and Pluto, unlike Titan. The origin of nitrogen on Enceladus is somewhat enigmatic. A scenario similar to Titan's, but with a role for the interior processes, may be at work. In this paper, we will discuss the source and loss of nitrogen for the above objects, and why Ganymede, the largest moon in the solar system, is nitrogen starved.

  5. Dengue virus inactivation by minipool TnBP/Triton X-45 treatment of plasma and cryoprecipitate.

    Science.gov (United States)

    Burnouf, T; Chou, M-L; Cheng, L-H; Li, Z-R; Wu, Y-W; El-Ekiaby, M; Tsai, K-H

    2013-01-01

    A minipool solvent/detergent (S/D; 1% TnBP/1% Triton X-45; 31°C) process was developed for viral inactivation of plasma and cryoprecipitate used for transfusion. The goal of this study was to determine the rate and extent of inactivation of dengue virus (DENV) during this process. DENV-1 was propagated using C6/36 mosquito cells to an infectivity titre close to 9 log and spiked (10% v/v) into individual plasma and cryoprecipitate samples from two distinct donors. Samples were taken right after spiking and during viral inactivation treatment by 1% TnBP-1% Triton X-45 at 31°C. DENV-1 infectivity was assessed on Vero E6 cells by a focus-forming assay (FFA). Culture medium and complement-inactivated plasma were used as experimental controls. Experiments were done in duplicate. DENV-1 infectivity was 7·5 log in spiked plasma and 7·1 and 7·3 log in spiked cryoprecipitate. There was no loss of DENV-1 infectivity in the spiked materials, nor in the controls not subjected to S/D treatment. No infectivity was found in plasma and cryoprecipitate subjected to S/D treatment at the first time-point evaluated (10 min). DENV-1 was strongly inactivated in plasma and cryoprecipitate, respectively, within 10 min of 1% TnBP/1% Triton X-45 treatment at 31°C. These data provide a reassurance of the safety of such S/D-treated plasma and cryoprecipitate with regard to the risk of transmission of all DENV serotypes and other flaviviruses. © 2012 The Author(s). Vox Sanguinis © 2012 International Society of Blood Transfusion.

  6. TRITON vs POLARIS. Comparison Between Two Modules for LWRs Modelling in SCALE 6.2

    Energy Technology Data Exchange (ETDEWEB)

    Labarile, A.; Barrachina, T.; Miró, R.; Verdú, G.

    2015-07-01

    -One of them challenges more important in the research of reactors nuclear is the development of codes of best estimate that allow decrease them uncertainties of them calculations increasing the reliability of the results. You will also need sensitivity and uncertainty analysis and validation of the implemented code. This work offers a comparison of two modules of SCALE-6.2 for the case of a reactor's water to pressure (PWR). Based is in data from plant of the reactor Three thousands Island-1 is has calculated the keff and the cross sections effective with two modules in two dimensions (2-D) of the program SCALE: TRITON and POLARIS. TRITON is a module already validated for the calculation of the transport as POLARIS is located in distribution from end of the 2014. The objective is to compare the results of keff and cross sections of two simulations, and carry out a sensitivity analysis and uncertainty of the results. In TRITON and POLARIS calculations have been made to fuel elements of the PWR Three thousand Island-1, in two different configurations (with and without control rods), condition of stop in hot (HZP) and condition of full power (HFP). The results are presented in this work. A good correlation between the results of two simulations has found and, in addition, POLARIS module has presented less computational time and good stability in the parameters. After having compared the results obtained, a sensitivity analysis has been carried out to confirm the validation of two modules and study the influence of uncertainties in the calculation of the fuel element. (Author)

  7. Retroperitoneal "triton" tumor. Report of a case and review of literature

    Directory of Open Access Journals (Sweden)

    Palacios Acosta José Martín

    2014-07-01

    Full Text Available The triton tumor was described in 1932 by Masson, as a peripheral nerve sheath malignancy with rabdomioblástica differentiation. The retroperitoneal location is extremely rare, only nine cases have been reported in children. The clinical picture depends on the size of the tumor and the organs involved, their retroperitoneal location is usually asymptomatic. The mainstay of treatment is the surgical excision of the tumor. We report the case of a child with retroperitoneal location of the tumor. A complete resection of it was performed. The patient had an uneventful postoperative course. He is currently under control. There is no evidence of relapse.

  8. Triton X-114 cloud point extraction to subfractionate blood plasma proteins for two-dimensional gel electrophoresis

    DEFF Research Database (Denmark)

    Jessen, Flemming; Wulff, Tune

    2015-01-01

    A simple and reproducible procedure for enrichment of a plasma protein subfraction suitable for two-dimensional polyacrylamide gel electrophoresis (2DE) was developed, using a Triton X-114-based cloud point extraction (CPE). Appropriate conditions for such a CPE procedure were found by SDS......-PAGE to be a plasma protein concentration of about 10mg/ml in 3% (w/v) Triton X-114. 2DE of proteins obtained by CPE of 400μl of human plasma revealed about 200 spots constituting a spot pattern very different from the pattern of total plasma. The CPE procedure only had a limited contribution to the technical......-sterol acyltransferase, serum amyloid A, and serum paraoxonase/arylesterase 1, which are proteins of a hydrophobic nature, as in plasma they relate to lipoprotein particles. Thus, Triton X-114-based CPE is a simple plasma prefractionation tool, attractive for detailed 2DE studies of hydrophobic plasma proteins...

  9. Exogenous Pulmonary Surfactant as a Vehicle for Antimicrobials: Assessment of Surfactant-Antibacterial Interactions In Vitro

    Directory of Open Access Journals (Sweden)

    Alexei Birkun

    2014-01-01

    Full Text Available Owing to its unique surface-active properties, an exogenous pulmonary surfactant may become a promising drug delivery agent, in particular, acting as a vehicle for antibiotics in topical treatment of pneumonia. The purpose of this study was to assess a mutual influence of natural surfactant preparation and three antibiotics (amikacin, cefepime, and colistimethate sodium in vitro and to identify appropriate combination(s for subsequent in vivo investigations of experimental surfactant/antibiotic mixtures. Influence of antibiotics on surface-active properties of exogenous surfactant was assessed using the modified Pattle method. Effects of exogenous surfactant on antibacterial activity of antimicrobials against Staphylococcus aureus, Klebsiella pneumoniae, and Pseudomonas aeruginosa were evaluated using conventional microbiologic procedures. Addition of amikacin or cefepime to surfactant had no significant influence on surface-active properties of the latter. Obvious reduction of surface-active properties was confirmed for surfactant/colistimethate composition. When suspended with antibiotics, surfactant either had no impact on their antimicrobial activity (amikacin or exerted mild to moderate influence (reduction of cefepime bactericidal activity and increase of colistimethate bacteriostatic activity against S. aureus and P. aeruginosa. Considering favorable compatibility profile, the surfactant/amikacin combination is advisable for subsequent investigation of joint surfactant/antibacterial therapy in animals with bacterial pneumonia.

  10. Exogenous Pulmonary Surfactant as a Vehicle for Antimicrobials: Assessment of Surfactant-Antibacterial Interactions In Vitro

    Science.gov (United States)

    2014-01-01

    Owing to its unique surface-active properties, an exogenous pulmonary surfactant may become a promising drug delivery agent, in particular, acting as a vehicle for antibiotics in topical treatment of pneumonia. The purpose of this study was to assess a mutual influence of natural surfactant preparation and three antibiotics (amikacin, cefepime, and colistimethate sodium) in vitro and to identify appropriate combination(s) for subsequent in vivo investigations of experimental surfactant/antibiotic mixtures. Influence of antibiotics on surface-active properties of exogenous surfactant was assessed using the modified Pattle method. Effects of exogenous surfactant on antibacterial activity of antimicrobials against Staphylococcus aureus, Klebsiella pneumoniae, and Pseudomonas aeruginosa were evaluated using conventional microbiologic procedures. Addition of amikacin or cefepime to surfactant had no significant influence on surface-active properties of the latter. Obvious reduction of surface-active properties was confirmed for surfactant/colistimethate composition. When suspended with antibiotics, surfactant either had no impact on their antimicrobial activity (amikacin) or exerted mild to moderate influence (reduction of cefepime bactericidal activity and increase of colistimethate bacteriostatic activity against S. aureus and P. aeruginosa). Considering favorable compatibility profile, the surfactant/amikacin combination is advisable for subsequent investigation of joint surfactant/antibacterial therapy in animals with bacterial pneumonia. PMID:24876994

  11. Different effects of surfactant proteins B and C - implications for development of synthetic surfactants.

    Science.gov (United States)

    Curstedt, Tore; Johansson, Jan

    2010-06-01

    Treatment of premature newborn rabbits with synthetic surfactants containing a surfactant protein C analogue in a simple phospholipid mixture gives similar tidal volumes as treatment with poractant alfa (Curosurf(R)) but ventilation with a positive end-expiratory pressure (PEEP) is needed for this synthetic surfactant to stabilize the alveoli at end-expiration. The effect on lung gas volumes seems to depend on the structure of the peptide since treatment with a synthetic surfactant containing the 21-residue peptide (LysLeu(4))(4)Lys (KL(4)) gives low lung gas volumes in experiments also performed with PEEP. Surfactant preparations containing both surfactant proteins B and C or their analogues prevent alveolar collapse at end-expiration even if ventilated without PEEP. Treatment of premature newborn rabbits with different natural surfactants indicates that both the lipid composition and the proteins are important in order to stabilize the alveoli at end-expiration. Synthetic surfactants containing two peptides may be able to replace natural surfactants within the near future but more trials need to be performed before any conclusion can be drawn about the ideal composition of this new generation of synthetic surfactants. Copyright 2010 S. Karger AG, Basel.

  12. Effect of the treatment with Euterpe oleracea Mart. oil in rats with Triton-induced dyslipidemia.

    Science.gov (United States)

    E Souza, Belmira S Faria; Carvalho, Helison O; Ferreira, Irlon M; da Cunha, Edilson L; Barros, Albenise Santana; Taglialegna, Talisson; Carvalho, José C T

    2017-06-01

    Dyslipidemias are defined as changes in lipid metabolism that have abnormal concentrations of lipids or lipoproteins in the bloodstream. Chronic increase in triglyceride and low-density lipoprotein (LDL-c) levels are known as risk factors for the atherogenesis process as well as other cardiovascular diseases (CVDs). The magnitude of the problems caused by dyslipidemias impels research by new agents that act in the prevention and control. Thus, products from the Amazonian biodiversity, such as Euterpe oleracea oil (OFEO), rich in unsaturated fatty acids (UFAs), constitutes a study source for the treatment of alterations in lipid metabolism. The present study aims to investigate the effect of OFEO treatment in rats with Triton-induced dyslipidemia (Tyloxapol WR1339). The physicochemical and chromatographic results confirmed the chemical composition of OFEO with a predominance of UFAs (67.83%), with Oleic acid being the majority (54.32%). At Triton-induced dyslipidemia, the animals treated with OFEO and Simvastatin showed a significant reduction in total cholesterol levels, with values ​​of 121.7±29.5 (pdyslipidemia, acting as antihypercholesterolemic and antihypertriglyceridemic, thus possibly contributing as a preventive agent for CVDs. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  13. Evaluation of hypolipidemic Marrubium vulgare effect in Triton WR-1339-induced hyperlipidemia in mice.

    Science.gov (United States)

    Ibrahim, Abeer Y; Hendawy, Saber F; Elsayed, Ahmed A A; Omer, Elsayed A

    2016-05-01

    To evaluate the hypocholesterolemic and hypotriglyceridemic activities of four Marrbium vulgare herb extracts using Triton WR-1339-induced hyperlipidemia in mice. Hyperlipidemia was developed by intraperitoneal injection of Triton (200 mg/kg body weight). The animals were divided into main four groups of eight mice each: normal control group, hyperlipidemic control group, hyperlipidemic plus tween-40 control and treated group. The fourth one was divided into four subgroups, petroleum ether extract group, chloroform extract group, ethyl acetate extract group and methanol extract treated group each of them contains two sub-sub group for treating animals with two doses at 0.1 and 0.25 LD50. After 7 h and 24 h of treatment, the intragastric administration of all extracts caused a significant decrease of plasma total cholesterol. Triglyceride levels were also significantly lowered by all extracts while petroleum ether produced the lowest decreasing level. Similar results were observed for LDL-cholesterol concentrations. Furthermore, more polar extracts (methanol and ethyl acetate)-soluble fractions showed a significant ameliorative action on elevated atherogenic index (AI) and LDL/HDL-C ratios, while these atherogenic markers were not statistically suppressed by the chloroform and petroleum ether-soluble extract. The findings indicated that Marrubium may contain polar products able to lower plasma lipid concentrations and might be beneficial in treatment of hyperlipidemia and atherosclerosis. Copyright © 2016 Hainan Medical College. Production and hosting by Elsevier B.V. All rights reserved.

  14. Time-resolved triton burnup measurement using the scintillating fiber detector in the Large Helical Device

    Science.gov (United States)

    Ogawa, K.; Isobe, M.; Nishitani, T.; Murakami, S.; Seki, R.; Nakata, M.; Takada, E.; Kawase, H.; Pu, N.; LHD Experiment Group

    2018-03-01

    Time-resolved measurement of triton burnup is performed with a scintillating fiber detector system in the deuterium operation of the large helical device. The scintillating fiber detector system is composed of the detector head consisting of 109 scintillating fibers having a diameter of 1 mm and a length of 100 mm embedded in the aluminum substrate, the magnetic registrant photomultiplier tube, and the data acquisition system equipped with 1 GHz sampling rate analogies to digital converter and the field programmable gate array. The discrimination level of 150 mV was set to extract the pulse signal induced by 14 MeV neutrons according to the pulse height spectra obtained in the experiment. The decay time of 14 MeV neutron emission rate after neutral beam is turned off measured by the scintillating fiber detector. The decay time is consistent with the decay time of total neutron emission rate corresponding to the 14 MeV neutrons measured by the neutron flux monitor as expected. Evaluation of the diffusion coefficient is conducted using a simple classical slowing-down model FBURN code. It is found that the diffusion coefficient of triton is evaluated to be less than 0.2 m2 s-1.

  15. SCALE Continuous-Energy Monte Carlo Depletion with Parallel KENO in TRITON

    International Nuclear Information System (INIS)

    Goluoglu, Sedat; Bekar, Kursat B.; Wiarda, Dorothea

    2012-01-01

    The TRITON sequence of the SCALE code system is a powerful and robust tool for performing multigroup (MG) reactor physics analysis using either the 2-D deterministic solver NEWT or the 3-D Monte Carlo transport code KENO. However, as with all MG codes, the accuracy of the results depends on the accuracy of the MG cross sections that are generated and/or used. While SCALE resonance self-shielding modules provide rigorous resonance self-shielding, they are based on 1-D models and therefore 2-D or 3-D effects such as heterogeneity of the lattice structures may render final MG cross sections inaccurate. Another potential drawback to MG Monte Carlo depletion is the need to perform resonance self-shielding calculations at each depletion step for each fuel segment that is being depleted. The CPU time and memory required for self-shielding calculations can often eclipse the resources needed for the Monte Carlo transport. This summary presents the results of the new continuous-energy (CE) calculation mode in TRITON. With the new capability, accurate reactor physics analyses can be performed for all types of systems using the SCALE Monte Carlo code KENO as the CE transport solver. In addition, transport calculations can be performed in parallel mode on multiple processors.

  16. Small angle neutron scattering study of doxorubicin–surfactant ...

    Indian Academy of Sciences (India)

    The binding affinity of doxorubicin within the micelle carrier is enhanced through complex formation of drug and anionic surfactant, aerosol OT (AOT). Electrostatic binding of doxorubicin with negatively charged surfactants leads to the formation of hydrophobic drug–surfactant complexes. Surfactant-induced partitioning of ...

  17. Characterizing adsorption of associating surfactants on carbonates surfaces.

    Science.gov (United States)

    Jian, Guoqing; Puerto, Maura; Wehowsky, Anna; Miller, Clarence; Hirasaki, George J; Biswal, Sibani L

    2018-03-01

    The adsorption of anionic surfactants onto positively charged carbonate minerals is typically high due to electrostatic interactions. By blending anionic surfactants with cationic or zwitterionic surfactants, which naturally form surfactant complexes, surfactant adsorption is expected to be influenced by a competition between surfactant complexes and surfactant-surface interactions. The adsorption behavior of surfactant blends known to form complexes was investigated. The surfactants probed include an anionic C 15-18 internal olefin sulfonate (IOS), a zwitterionic lauryl betaine (LB), and an anionic C 13 -alcohol polyethylene glycol ether carboxylic acid (L38). An analytical method based on high-performance liquid chromatography evaporative light scattering detector (HPLC-ELSD) was developed to measure three individual surfactant concentrations from a blended surfactant solution. The adsorption of the individual surfactants and surfactant blends were systematically investigated on different mineral surfaces using varying brine solutions. LB adsorption on calcite surfaces was found to be significantly increased when blended with IOS or L38 since it forms surfactant complexes that partition to the surface. However, the total adsorption of the LB-IOS-L38 solution on dolomite decreased from 3.09 mg/m 2 to 1.97 mg/m 2 when blended together compared to summing the adsorption values of individual surfactants, which highlights the importance of mixed surfactant association. Copyright © 2017 Elsevier Inc. All rights reserved.

  18. Enhancing the performance of dye-sensitized solar cells by incorporating nanosilicate platelets in gel electrolyte

    KAUST Repository

    Lai, Yi-Hsuan

    2009-10-01

    Two kinds of gel-type dye-sensitized solar cells (DSSCs), composed of two types of electrolytes, were constructed and the respective cell performance was evaluated in this study. One electrolyte, TEOS-Triton X-100 gel, was based on a hybrid organic/inorganic gel electrolyte made by the sol-gel method and the other was based on poly(vinyidene fluoride-co-hexafluoro propylene) (PVDF-HFP) copolymer. TEOS-Triton X-100 gel was based on the reticulate structure of silica, formed by hydrolysis, and condensation of tetraethoxysilane (TEOS), while its organic subphase was a mixture of surfactant (Triton X-100) and ionic liquid electrolytes. Both DSSC gel-type electrolytes were composed of iodine, 1-propy-3-methyl-imidazolium iodide, and 3-methoxypropionitrile to create the redox couple of I3 -/I-. Based on the results obtained from the I-V characteristics, it was found that the optimal iodine concentrations for the TEOS-Triton X-100 gel electrolyte and PVDF-HFP gel electrolyte are 0.05 M and 0.1 M, respectively. Although the increase in the iodine concentration could enhance the short-circuit current density (JSC), a further increase in the iodine concentration would reduce the JSC due to increased dark current. Therefore, the concentration of I2 is a significant factor in determining the performance of DSSCs. In order to enhance cell performance, the addition of nanosilicate platelets (NSPs) in the above-mentioned gel electrolytes was investigated. By incorporating NSP-Triton X-100 into the electrolytes, the JSC of the cells increased due to the decrease of diffusion resistance, while the open circuit voltage (VOC) remained almost the same. As the loading of the NSP-Triton X-100 in the TEOS-Triton X-100 gel electrolyte increased to 0.5 wt%, the JSC and the conversion efficiency increased from 8.5 to 12 mA/cm2 and from 3.6% to 4.7%, respectively. However, the JSC decreased as the loading of NSP-Triton X-100 exceeded 0.5 wt%. At higher NSP-Triton X-100 loading, NSPs acted as

  19. DNA compaction by azobenzene-containing surfactant

    International Nuclear Information System (INIS)

    Zakrevskyy, Yuriy; Kopyshev, Alexey; Lomadze, Nino; Santer, Svetlana; Morozova, Elena; Lysyakova, Ludmila; Kasyanenko, Nina

    2011-01-01

    We report on the interaction of cationic azobenzene-containing surfactant with DNA investigated by absorption and fluorescence spectroscopy, dynamic light scattering, and atomic force microscopy. The properties of the surfactant can be controlled with light by reversible switching of the azobenzene unit, incorporated into the surfactant tail, between a hydrophobic trans (visible irradiation) and a hydrophilic cis (UV irradiation) configuration. The influence of the trans-cis isomerization of the azobenzene on the compaction process of DNA molecules and the role of both isomers in the formation and colloidal stability of DNA-surfactant complexes is discussed. It is shown that the trans isomer plays a major role in the DNA compaction process. The influence of the cis isomer on the DNA coil configuration is rather small. The construction of a phase diagram of the DNA concentration versus surfactant/DNA charge ratio allows distancing between three major phases: colloidally stable and unstable compacted globules, and extended coil conformation. There is a critical concentration of DNA above which the compacted globules can be hindered from aggregation and precipitation by adding an appropriate amount of the surfactant in the trans configuration. This is because of the compensation of hydrophobicity of the globules with an increasing amount of the surfactant. Below the critical DNA concentration, the compacted globules are colloidally stable and can be reversibly transferred with light to an extended coil state.

  20. Surfactants tailored by the class Actinobacteria

    Directory of Open Access Journals (Sweden)

    Johannes H Kügler

    2015-03-01

    Full Text Available Gloablly, the drive towards the establishment of a bio-based economy has resulted in an increased need for bio-based applications. This, in turn, has served as a driving force for the discovery and application of novel biosurfactants. The class Actinobacteria represents a vast group of microorganisms with the ability to produce a diverse range of secondary metabolites, including surfactants. Understanding the extensive nature of the biosurfactants produced by actinobacterial strains can assist in finding novel biosurfactants with new potential applications. This review therefore presents a comprehensive overview of the knowledge available on actinobacterial surfactants, the chemical structures that have been completely or partly elucidated, as well as the identity of the biosurfactant-producing strains. Producer strains of not yet elucidated compounds are discussed, as well as the original habitats of all the producer strains, which seems to indicate that biosurfactant production is environmentally driven. Methodology applied in the isolation, purification and structural elucidation of the different types of surface active compounds, as well as surfactant activity tests, are also discussed. Overall, actinobacterial surfactants can be summarized to include the dominantly occurring trehalose-comprising surfactants, other non-trehalose containing glycolipids, lipopeptides and the more rare actinobacterial surfactants. The lack of structural information on a large proportion of actinobacterial surfactants should be considered as a driving force to further explore the abundance and diversity of these compounds. This would allow for a better understanding of actinobacterial surface active compounds and their potential for biotechnological application.

  1. Surfactants tailored by the class Actinobacteria

    Science.gov (United States)

    Kügler, Johannes H.; Le Roes-Hill, Marilize; Syldatk, Christoph; Hausmann, Rudolf

    2015-01-01

    Globally the change towards the establishment of a bio-based economy has resulted in an increased need for bio-based applications. This, in turn, has served as a driving force for the discovery and application of novel biosurfactants. The class Actinobacteria represents a vast group of microorganisms with the ability to produce a diverse range of secondary metabolites, including surfactants. Understanding the extensive nature of the biosurfactants produced by actinobacterial strains can assist in finding novel biosurfactants with new potential applications. This review therefore presents a comprehensive overview of the knowledge available on actinobacterial surfactants, the chemical structures that have been completely or partly elucidated, as well as the identity of the biosurfactant-producing strains. Producer strains of not yet elucidated compounds are discussed, as well as the original habitats of all the producer strains, which seems to indicate that biosurfactant production is environmentally driven. Methodology applied in the isolation, purification and structural elucidation of the different types of surface active compounds, as well as surfactant activity tests, are also discussed. Overall, actinobacterial surfactants can be summarized to include the dominantly occurring trehalose-comprising surfactants, other non-trehalose containing glycolipids, lipopeptides and the more rare actinobacterial surfactants. The lack of structural information on a large proportion of actinobacterial surfactants should be considered as a driving force to further explore the abundance and diversity of these compounds. This would allow for a better understanding of actinobacterial surface active compounds and their potential for biotechnological application. PMID:25852670

  2. Tunable, antibacterial activity of silicone polyether surfactants.

    Science.gov (United States)

    Khan, Madiha F; Zepeda-Velazquez, Laura; Brook, Michael A

    2015-08-01

    Silicone surfactants are used in a variety of applications, however, limited data is available on the relationship between surfactant structure and biological activity. A series of seven nonionic, silicone polyether surfactants with known structures was tested for in vitro antibacterial activity against Escherichia coli BL21. The compounds varied in their hydrophobic head, comprised of branched silicone structures with 3-10 siloxane linkages and, in two cases, phenyl substitution, and hydrophilic tail of 8-44 poly(ethylene glycol) units. The surfactants were tested at three concentrations: below, at, and above their Critical Micelle Concentrations (CMC) against 5 concentrations of E. coli BL21 in a three-step assay comprised of a 14-24h turbidometric screen, a live-dead stain and viable colony counts. The bacterial concentration had little effect on antibacterial activity. For most of the surfactants, antibacterial activity was higher at concentrations above the CMC. Surfactants with smaller silicone head groups had as much as 4 times the bioactivity of surfactants with larger groups, with the smallest hydrophobe exhibiting potency equivalent to sodium dodecyl sulfate (SDS). Smaller PEG chains were similarly associated with higher potency. These data link lower micelle stability and enhanced permeability of smaller silicone head groups to antibacterial activity. The results demonstrate that simple manipulation of nonionic silicone polyether structure leads to significant changes in antibacterial activity. Copyright © 2015 Elsevier B.V. All rights reserved.

  3. Rhamnolipids--next generation surfactants?

    Science.gov (United States)

    Müller, Markus Michael; Kügler, Johannes H; Henkel, Marius; Gerlitzki, Melanie; Hörmann, Barbara; Pöhnlein, Martin; Syldatk, Christoph; Hausmann, Rudolf

    2012-12-31

    The demand for bio-based processes and materials in the petrochemical industry has significantly increased during the last decade because of the expected running out of petroleum. This trend can be ascribed to three main causes: (1) the increased use of renewable resources for chemical synthesis of already established product classes, (2) the replacement of chemical synthesis of already established product classes by new biotechnological processes based on renewable resources, and (3) the biotechnological production of new molecules with new features or better performances than already established comparable chemically synthesized products. All three approaches are currently being pursued for surfactant production. Biosurfactants are a very promising and interesting substance class because they are based on renewable resources, sustainable, and biologically degradable. Alkyl polyglycosides are chemically synthesized biosurfactants established on the surfactant market. The first microbiological biosurfactants on the market were sophorolipids. Of all currently known biosurfactants, rhamnolipids have the highest potential for becoming the next generation of biosurfactants introduced on the market. Although the metabolic pathways and genetic regulation of biosynthesis are known qualitatively, the quantitative understanding relevant for bioreactor cultivation is still missing. Additionally, high product titers have been exclusively described with vegetable oil as sole carbon source in combination with Pseudomonas aeruginosa strains. Competitive productivity is still out of reach for heterologous hosts or non-pathogenic natural producer strains. Thus, on the one hand there is a need to gain a deeper understanding of the regulation of rhamnolipid production on process and cellular level during bioreactor cultivations. On the other hand, there is a need for metabolizable renewable substrates, which do not compete with food and feed. A sustainable bioeconomy approach should

  4. Gemini surfactants from natural amino acids.

    Science.gov (United States)

    Pérez, Lourdes; Pinazo, Aurora; Pons, Ramon; Infante, Mrosa

    2014-03-01

    In this review, we report the most important contributions in the structure, synthesis, physicochemical (surface adsorption, aggregation and phase behaviour) and biological properties (toxicity, antimicrobial activity and biodegradation) of Gemini natural amino acid-based surfactants, and some potential applications, with an emphasis on the use of these surfactants as non-viral delivery system agents. Gemini surfactants derived from basic (Arg, Lys), neutral (Ser, Ala, Sar), acid (Asp) and sulphur containing amino acids (Cys) as polar head groups, and Geminis with amino acids/peptides in the spacer chain are reviewed. © 2013.

  5. Mechanism of bacterial inactivation by cationic surfactants

    Energy Technology Data Exchange (ETDEWEB)

    Pavlova, I.B.; Samoylenko, I.I.

    1985-03-01

    The mechanism of bacteriocidal action of the cationic surfactant dimethylbenzylammonium chloride was studied on exposure of Staphylococcus aureus, Streptococcus faecium, Bacillus subtilis and Escherichia coli to different concentrations of the agent and determinations of survival plots. The data showed that the surfactant was bacteriocidal for all the bacteria tested at a concentration of 0.0001%, but more efficient in the case of the gram positives. Electron microscopy showed considerable damage and dissarrangement of the cytoplasmic membrane, indicating that the killing mechanism involved this organelle. It appears that cationic surfactants may constitute effective disinfectant preparations. 9 references, 2 figures.

  6. Surfactant-Assisted Coal Liquefaction

    Science.gov (United States)

    Hickey, Gregory S.; Sharma, Pramod K.

    1993-01-01

    Obtaining liquid fuels from coal which are economically competitive with those obtained from petroleum based sources is a significant challenge for the researcher as well as the chemical industry. Presently, the economics of coal liquefaction are not favorable because of relatively intense processing conditions (temperatures of 430 degrees C and pressures of 2200 psig), use of a costly catalyst, and a low quality product slate of relatively high boiling fractions. The economics could be made more favorable by achieving adequate coal conversions at less intense processing conditions and improving the product slate. A study has been carried out to examine the effect of a surfactant in reducing particle agglomeration and improving hydrodynamics in the coal liquefaction reactor to increase coal conversions...

  7. Synthesis of bimetallic nanocompositions AuxPd1-x/γ-Al2O3 for catalytic CO oxidation

    Science.gov (United States)

    Zaytsev, S. Yu.; Plyusnin, P. E.; Slavinskaya, E. M.; Shubin, Yu. V.

    2017-11-01

    Colloidal suspensions of AuxPd1-x nanoalloys were prepared via hydrazine co-reduction of [AuCl4]- and [PdCl4]2- complex anions in aqueous solution. High molecular weight polymeric compounds polyvinylpyrrolidone (PVP), polyvinyl alcohol (PVA), and cryptoionic surfactants (AF-6 and AF-12 neonols, Triton X-100) were used as surface capping agents. Nanoparticles prepared under different experimental conditions were immobilized on γ-Al2O3 supports. The removal of the capping agents from the surface of the active particles was achieved through calcination of samples in oxidative atmosphere (air, 500 °C). This pretreatment of the catalysts significantly enhances their performance. Powder XRD, TEM, and EDX were employed to characterize the structure, size, and composition of the AuxPd1-x/γ-Al2O3 catalysts. The immobilized particles consist of uniformly mixed alloys having multi-domain face-centered cubic structure with typical crystallite size of 3-6 nm. The activity of the prepared samples was examined with temperature-programmed CO oxidation reaction (TP-CO+O2). Triton X-100 surfactant is superior in a number of parameters. Among all AuxPd1-x/γ-Al2O3 catalysts tested, the one stabilized with Triton X-100 (0.4%Au-0.2%Pd@Triton X-100) was found to have the highest activity for conversion of CO into CO2.

  8. Effect of mesoporous g-C3N4 substrate on catalytic oxidation of CO over Co3O4

    Science.gov (United States)

    Yang, Heng; Lv, Kangle; Zhu, Junjiang; Li, Qin; Tang, Dingguo; Ho, Wingkei; Li, Mei; Carabineiro, Sónia A. C.

    2017-04-01

    Mesoporous graphitic carbon nitride (mpg-CN) was synthesized using Triton X-100, a surfactant containing a hydrophilic polyethylene oxide group and a tert-octyl-phenyl hydrophobic moiety, as a soft template. The obtained mpg-CN was used as a support for Co3O4, and this supported catalyst was used for CO oxidation. The effects of the amount of Triton X-100, weight ratio of Co3O4 to mpg-CN and calcination temperature on the catalytic performances for CO oxidation of Co3O4/mpg-CN composites were systematically studied. It was found that the presence of Triton X-100 not only retarded the polymerization of dicyandiamide, but also affected the microstructure of Co3O4. Bubbles formed because of the hydrophobic group of the surfactant Triton X-100 can be act as a soft template for the synthesis of mesoporous g-C3N4. The enhanced catalytic activity of Co3O4/mpg-CN was attributed to a synergistic effect, enlarged BET surface areas, increased Co3+ and lattice oxygen contents, and the porous structure of mpg-CN support. The high stability of 12.5% Co3O4/mpg-CN(1.0) makes it a promising catalyst for practical applications.

  9. Isolation of Surfactant-Resistant Bacteria from Natural, Surfactant-Rich Marine Habitats▿

    OpenAIRE

    Plante, Craig J.; Coe, Kieran M.; Plante, Rebecca G.

    2008-01-01

    Environmental remediation efforts often utilize either biodegradative microbes or surfactants, but not in combination. Coupling both strategies holds the potential to dramatically increase the rate and extent of remediation because surfactants can enhance the bioavailability of contaminants to microbes. However, many surfactants permeabilize bacterial cell membranes and are effective disinfectants. An important goal then is to find or genetically modify microorganisms that possess both desira...

  10. Pulmonary Surfactants for Acute and Chronic Lung Diseases (Part I

    Directory of Open Access Journals (Sweden)

    O. A. Rozenberg

    2014-01-01

    Full Text Available Part 1 of the review gives information on the composition and properties of a pulmonary surfactant and quantitative and qual itative impairments in the pulmonary surfactant system in different neonatal and adult abnormalities and describes the composition of commercial synthetic and natural surfactants. The results of surfactant therapy for respiratory distress syndrome and other lung diseases with secondary surfactant deficiency in the newborns are analyzed.

  11. Lung surfactant levels are regulated by Ig-Hepta/GPR116 by monitoring surfactant protein D.

    Directory of Open Access Journals (Sweden)

    Taku Fukuzawa

    Full Text Available Lung surfactant is a complex mixture of lipids and proteins, which is secreted from the alveolar type II epithelial cell and coats the surface of alveoli as a thin layer. It plays a crucial role in the prevention of alveolar collapse through its ability to reduce surface tension. Under normal conditions, surfactant homeostasis is maintained by balancing its release and the uptake by the type II cell for recycling and the internalization by alveolar macrophages for degradation. Little is known about how the surfactant pool is monitored and regulated. Here we show, by an analysis of gene-targeted mice exhibiting massive accumulation of surfactant, that Ig-Hepta/GPR116, an orphan receptor, is expressed on the type II cell and sensing the amount of surfactant by monitoring one of its protein components, surfactant protein D, and its deletion results in a pulmonary alveolar proteinosis and emphysema-like pathology. By a coexpression experiment with Sp-D and the extracellular region of Ig-Hepta/GPR116 followed by immunoprecipitation, we identified Sp-D as the ligand of Ig-Hepta/GPR116. Analyses of surfactant metabolism in Ig-Hepta(+/+ and Ig-Hepta(-/- mice by using radioactive tracers indicated that the Ig-Hepta/GPR116 signaling system exerts attenuating effects on (i balanced synthesis of surfactant lipids and proteins and (ii surfactant secretion, and (iii a stimulating effect on recycling (uptake in response to elevated levels of Sp-D in alveolar space.

  12. Surface film formation in vitro by infant and therapeutic surfactants: role of surfactant protein B.

    Science.gov (United States)

    Danhaive, Olivier; Chapin, Cheryl; Horneman, Hart; Cogo, Paola E; Ballard, Philip L

    2015-02-01

    Pulmonary surfactant provides an alveolar surface-active film that is critical for normal lung function. Our objective was to determine in vitro film formation properties of therapeutic and infant surfactants and the influence of surfactant protein (SP)-B content. We used a multiwell fluorescent assay measuring maximum phospholipid surface accumulation (Max), phospholipid concentration required for half-maximal film formation (½Max), and time for maximal accumulation (tMax). Among five therapeutic surfactants, calfactant (highest SP-B content) had film formation values similar to natural surfactant, and addition of SP-B to beractant (lowest SP-B) normalized its Max value. Addition of budesonide to calfactant did not adversely affect film formation. In tracheal aspirates of preterm infants with evolving chronic lung disease, SP-B content correlated with ½Max and tMax values, and SP-B supplementation of SP-B-deficient infant surfactant restored normal film formation. Reconstitution of normal surfactant indicated a role for both SP-B and SP-C in film formation. Film formation in vitro differs among therapeutic surfactants and is highly dependent on SP-B content in infant surfactant. The results support a critical role of SP-B for promoting surface film formation.

  13. Poly(ethylene oxide) surfactant polymers

    OpenAIRE

    VACHEETHASANEE, KATANCHALEE; WANG, SHUWU; QIU, YONGXING; MARCHANT, ROGER E.

    2004-01-01

    We report on a series of structurally well-defined surfactant polymers that undergo surface-induced self-assembly on hydrophobic biomaterial surfaces. The surfactant polymers consist of a poly(vinyl amine) backbone with poly(ethylene oxide) and hexanal pendant groups. The poly(vinyl amine) (PVAm) was synthesized by hydrolysis of poly(N-vinyl formamide) following free radical polymerization of N-vinyl formamide. Hexanal and aldehyde-terminated poly (ethyleneoxide) (PEO) were simultaneously att...

  14. [Optimizing synthesis of conjugates of superoxide dismutase and catalase with aldehyde dextrans in surfactant microemulsions in heptane].

    Science.gov (United States)

    Eremin, A N; Metelitsa, D I

    1997-01-01

    Stable microemulsions in heptane retaining considerable amounts of the polar phase were obtained by using Aerosol OT (AOT), Triton X-45, and catalase. Conjugates of superoxide dismutase (SOD) and catalase with aldehyde dextrans (AD) were synthesized in surfactant microemulsions in heptane. Effects of the reaction duration, the microemulsion polar phase volume, and concentrations of enzymes and modifiers on the properties of these conjugates were studied. The catalytic properties of conjugates depended on the nature of the surfactants used to stabilize the microemulsions, the initial concentration of protein in the reaction mixture, and the enzyme: modifier ratio. The degree of modification of the enzymes and the stabilities of their conjugates during isolation from microemulsions by a water-acetone solution depended on the concentration of the AD used. The catalytic properties of the conjugates synthesized were compared, and their stabilities in the presence of H2O2 were described. We suggested a simple method of transformation of whole kinetic curves of H2O2 conversion in coordinates 1/ln([H2O2]0/[H2O2]t - 1/t for simultaneous measurement of the constant of the catalase inactivation rate by H2O2 (Cin, S-1) and the rate constant of the catalase complex 1 interaction with the second H2O2 molecule (C2, M-1 S-1). This method was tested experimentally. Values C2 and Cin for catalase and its conjugates with ADs were compared, and these results were discussed.

  15. Neuropeptides encoded within a neural transcriptome of the giant triton snail Charonia tritonis, a Crown-of-Thorns Starfish predator.

    Science.gov (United States)

    Bose, U; Suwansa-Ard, S; Maikaeo, L; Motti, C A; Hall, M R; Cummins, S F

    2017-12-01

    Neuropeptides represent a diverse class of signaling molecules originating from neural tissues. These chemical modulators orchestrate complex physiological events including those associated with growth and reproduction. De novo transcriptome sequencing of a cerebral ganglion library of the endangered giant triton snail (Charonia tritonis) was undertaken in an effort to identify key neuropeptides that control or influence its physiology. The giant triton snail is considered a primary predator of the corallivore Acanthaster planci (Crown-of-Thorns Starfish) that is responsible for a significant loss in coral cover on reefs in the Indo-Pacific. The transcriptome library was assembled into contigs, and then bioinformatic analysis was used to identify a repertoire of 38 giant triton snail neuropeptide precursor genes, and various isoforms, that encode conserved molluscan neuropeptides. C. tritonis neuropeptides show overall precursor organisation consistent with those of other molluscs. These include those neuropeptides associated with mollusc reproduction such as the APGWamide, buccalin, conopressin, gonadotropin-releasing hormone (GnRH), NKY and egg-laying hormone. These data provide a foundation for further studies targeted towards the functional characterisation of neuropeptides to further understand aspects of the biology of the giant triton snail, such as elucidating its reproductive neuroendocrine pathway to allow the development of knowledge based captive breeding programs. Copyright © 2017 Elsevier Inc. All rights reserved.

  16. Hypolipidemic effect and antioxidant activity of glycoprotein isolated from Ulmus davidiana Nakai in Triton WR-1339-treated mouse.

    Science.gov (United States)

    Ko, Jeong-Hyeon; Lee, Sei-Jung; Lim, Kye-Taek

    2007-01-01

    The glycoprotein isolated from Ulmus davidiana Nakai (UDN) (UDN glycoprotein) has a molecular weight of 116 kDa and consists of 78.65% carbohydrate content and 21.35% protein content. In the present study, we investigated the hypolipidemic effect of UDN glycoprotein on Triton WR-1339-induced mice. With pretreatment with UDN glycoprotein, the triacylglycerol (TAG), total cholesterol and low density lipoprotein-cholesterol (LDL-C) concentrations were significantly reduced, whereas high density lipoprotein-cholesterol (HDL-C) concentration was increased in the plasma of Triton WR-1339-induced mice. With respect to antioxidative activity, UDN glycoprotein significantly decreased the level of thiobarbituric acid reactive substances (TBARS) and improved activities of catalase and glutathione peroxidase (GPx), without an apparent change of superoxide dismutase (SOD) activity. Also UDN glycoprotein significantly increased nitric oxide (NO) production in Triton WR-1339-induced mice. These results indicate that UDN glycoprotein has a hypolipidemic effect, possesses antioxidant activity and has an ability to stimulate NO production. Thus, we speculate that UDN glycoprotein is an example of natural compound that lowers plasma lipid level together with having an antioxidant function in Triton WR-1339-induced mice.

  17. Determination of the ratio of axial-vector-to-vector weak coupling constants for beta decay of triton

    CERN Document Server

    Akulov, Y A

    2002-01-01

    Data on the chemical shifts of half-lives for atomic and molecular tritium were used to determine the ratio of axial-vector-to-vector weak coupling constants for beta decay of triton (G sub A /G sub V) sub t = -1.2646 +- 0.0035

  18. DILUTE SURFACTANT METHODS FOR CARBONATE FORMATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Kishore K. Mohanty

    2003-07-01

    There are many carbonate reservoirs in US (and the world) with light oil and fracture pressure below its minimum miscibility pressure (or reservoir may be naturally fractured). Many carbonate reservoirs are naturally fractured. Waterflooding is effective in fractured reservoirs, if the formation is water-wet. Many fractured carbonate reservoirs, however, are mixed-wet and recoveries with conventional methods are low (less than 10%). Thermal and miscible tertiary recovery techniques are not effective in these reservoirs. Surfactant flooding (or huff-n-puff) is the only hope, yet it was developed for sandstone reservoirs in the past. The goal of this research is to evaluate dilute (hence relatively inexpensive) surfactant methods for carbonate formations and identify conditions under which they can be effective. We have conducted adsorption, phase behavior and wettability studies. Addition of Na{sub 2}CO{sub 3} decreases IFT with a minimum at about 0.2 M. Addition of surfactant decreases IFT further. In the absence of surfactant the minerals are oil wet after aging with crude oil. Addition of surfactant solution decreases the contact angle to intermediate wettability. Addition of Na{sub 2}CO{sub 3} decreases anionic surfactant adsorption on calcite surface. Plans for the next quarter include conducting adsorption, phase behavior and wettability studies.

  19. [Deficiency of surfactant protein: Case report].

    Science.gov (United States)

    Milet, María Beatriz; Mena N, Patricia; Pérez, Héctor I; Espinoza, Tatiana

    Congenital surfactant deficiency is a condition infrequently diagnosed in newborns. A clinical case is presented of surfactant protein B deficiency. A review is performed on the study, treatment and differential diagnosis of surfactant protein deficiencies and infant chronic interstitial lung disease. The case is presented of a term newborn that developed respiratory distress, recurrent pulmonary opacification, and a transient response to the administration of surfactant. Immunohistochemical and genetic studies confirmed the diagnosis of surfactant protein B deficiency. Pulmonary congenital anomalies require a high index of suspicion. Surfactant protein B deficiency is clinically progressive and fatal in the majority of the cases, similar to that of ATP binding cassette subfamily A member 3 (ABCA3) deficiency. Protein C deficiency is insidious and may present with a radiological pulmonary interstitial pattern. Due to the similarity in the histological pattern, genetic studies help to achieve greater certainty in the prognosis and the possibility of providing adequate genetic counselling. Copyright © 2016 Sociedad Chilena de Pediatría. Publicado por Elsevier España, S.L.U. All rights reserved.

  20. 3X-100 blade field test.

    Energy Technology Data Exchange (ETDEWEB)

    Zayas, Jose R.; Johnson, Wesley D.

    2008-03-01

    In support of a Work-For-Other (WFO) agreement between the Wind Energy Technology Department at Sandia National Laboratories and 3TEX, one of the three Micon 65/13M wind turbines at the USDA Agriculture Research Service (ARS) center in Bushland, Texas, has been used to test a set of 9 meter wind turbine blades, manufactured by TPI composites using the 3TEX carbon material for the spar cap. Data collected from the test has been analyzed to evaluate both the aerodynamic performance and the structural response from the blades. The blades aerodynamic and structural performance, the meteorological inflow and the wind turbine structural response has been monitored with an array of 57 instruments: 15 to characterize the blades, 13 to characterize inflow, and 15 to characterize the time-varying state of the turbine. For the test, data was sampled at a rate of 40 Hz using the ATLAS II (Accurate GPS Time-Linked Data Acquisition System) data acquisition system. The system features a time-synchronized continuous data stream and telemetered data from the turbine rotor. This paper documents the instruments and infrastructure that have been developed to monitor these blades, turbines and inflow, as well as both modeling and field testing results.

  1. Interactions of organic contaminants with mineral-adsorbed surfactants

    Science.gov (United States)

    Zhu, L.; Chen, B.; Tao, S.; Chiou, C.T.

    2003-01-01

    Sorption of organic contaminants (phenol, p-nitrophenol, and naphthalene) to natural solids (soils and bentonite) with and without myristylpyridinium bromide (MPB) cationic surfactant was studied to provide novel insight to interactions of contaminants with the mineral-adsorbed surfactant. Contaminant sorption coefficients with mineral-adsorbed surfactants, Kss, show a strong dependence on surfactant loading in the solid. At low surfactant levels, the Kss values increased with increasing sorbed surfactant mass, reached a maximum, and then decreased with increasing surfactant loading. The Kss values for contaminants were always higher than respective partition coefficients with surfactant micelles (Kmc) and natural organic matter (Koc). At examined MPB concentrations in water the three organic contaminants showed little solubility enhancement by MPB. At low sorbed-surfactant levels, the resulting mineral-adsorbed surfactant via the cation-exchange process appears to form a thin organic film, which effectively "adsorbs" the contaminants, resulting in very high Kss values. At high surfactant levels, the sorbed surfactant on minerals appears to form a bulklike medium that behaves essentially as a partition phase (rather than an adsorptive surface), with the resulting Kss being significantly decreased and less dependent on the MPB loading. The results provide a reference to the use of surfactants for remediation of contaminated soils/sediments or groundwater in engineered surfactant-enhanced washing.

  2. Membrane fouling and wetting in membrane distillation and their mitigation by novel membranes with special wettability.

    Science.gov (United States)

    Wang, Zhangxin; Lin, Shihong

    2017-04-01

    Membrane distillation (MD) has been identified as a promising technology to desalinate the hypersaline wastewaters from fracking and other industries. However, conventional hydrophobic MD membranes are highly susceptible to fouling and/or wetting by the hydrophobic and/or amphiphilic constituents in these wastewaters of complex compositions. This study systematically investigates the impact of the surface wetting properties on the membrane wetting and/or fouling behaviors in MD. Specifically, we compare the wetting and fouling resistance of three types of membranes of different wetting properties, including hydrophobic and omniphobic membranes as well as composite membranes with a hydrophobic substrate and a superhydrophilic top surface. We challenged the MD membranes with hypersaline feed solutions that contained a relatively high concentration of crude oil with and without added synthetic surfactants, Triton X-100. We found that the composite membranes with superhydrophilic top surface were robustly resistant to oil fouling in the absence of Triton X-100, but were subject to pore wetting in the presence of Triton X-100. On the other hand, the omniphobic membranes were easily fouled by oil-in-water emulsion without Triton X-100, but successfully sustained stable MD performance with Triton X-100 stabilized oil-in-water emulsion as the feed solution. In contrast, the conventional hydrophobic membranes failed readily regardless whether Triton X-100 was present, although via different mechanisms. These findings are corroborated by contact angle measures as well as oil-probe force spectroscopy. This study provides a holistic picture regarding how a hydrophobic membrane fails in MD and how we can leverage membranes with special wettability to prevent membrane failure in MD operations. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Surfactant nebulization versus instillation during high frequency ventilation in surfactant-deficient rabbits

    NARCIS (Netherlands)

    Dijk, Peter H.; Heikamp, A; Bambang Oetomo, Sidarto

    1998-01-01

    Surfactant nebulization improves lung function at low alveolar doses of surfactant. However, efficiency of nebulization is low, and lung deposition seems to depend on lung aeration. High frequency ventilation (HFV) has been shown to improve lung aeration. We hypothesize that the combination of HFV

  4. Size control of surfactant vesicles made by a mixture of cationic surfactants and organic derivatives.

    Science.gov (United States)

    Kim, Tae-Hwan; Han, Young-Soo; Jang, Jong-Dae; Seong, Baek-Seok

    2014-10-01

    Spontaneous size-controllable vesicles that are prepared by a mixture of surfactants with different alkyl chain lengths (n-alkyltrimethylammonium bromide, C(n)TAB) and an organic derivative (5-methyl salicylic acid, 5mS) in aqueous solution have been investigated. When the organic derivative 5mS is mixed with the C(n)TAB surfactants in aqueous solution, the surfactant vesicles are spontaneously formed above a certain 5mS concentration. Small angle neutron scattering reveals that the core radius of surfactant vesicles is clearly increased from ca. 31 nm to ca. 97 nm with the alkyl chain length of surfactants while the bilayer thickness of the vesicles is nearly constant. The structure of surfactant vesicles maintains against temperature change ranging from 30 degrees C to 45 degrees C, showing no structural change. These results can provide thermally stable surfactant vesicles with various sizes and constant bilayer thickness that may possess a different permeability and may allow the surfactant vesicle to be used in gene or drug delivery for a variety of goods.

  5. Surfactant Delivery into the Lung

    Science.gov (United States)

    Grotberg, James; Filoche, Marcel

    2014-11-01

    We have developed a multiscale, compartmentalized model of surfactant and liquid delivery into the lung. Assuming liquid plug propagation, the airway compartment accounts for the plug's volume deposition (coating) on the airway wall, while the bifurcation compartment accounts for plug splitting from the parent airway to the two daughter airways. Generally the split is unequal due to gravity and geometry effects. Both the deposition ratio RD (deposition volume/airway volume), and the splitting ratio, RS, of the daughters volumes are solved independently from one another. Then they are used in a 3D airway network geometry to achieve the distribution of delivery into the lung. The airway geometry is selected for neonatal as well as adult applications, and can be advanced from symmetric, to stochastically asymmetric, to personalized. RD depends primarily on the capillary number, Ca, while RS depends on Ca, the Reynolds number, Re, the Bond number, Bo, the dose volume, VD, and the branch angles. The model predicts the distribution of coating on the airway walls and the remaining plug volume delivered to the alveolar region at the end of the tree. Using this model, we are able to simulate and test various delivery protocols, in order to optimize delivery and improve the respiratory function.

  6. Dilute Surfactant Methods for Carbonate Formations

    Energy Technology Data Exchange (ETDEWEB)

    Kishore K. Mohanty

    2006-02-01

    There are many fractured carbonate reservoirs in US (and the world) with light oil. Waterflooding is effective in fractured reservoirs, if the formation is water-wet. Many fractured carbonate reservoirs, however, are mixed-wet and recoveries with conventional methods are low (less than 10%). The process of using dilute anionic surfactants in alkaline solutions has been investigated in this work for oil recovery from fractured oil-wet carbonate reservoirs both experimentally and numerically. This process is a surfactant-aided gravity drainage where surfactant diffuses into the matrix, lowers IFT and contact angle, which decrease capillary pressure and increase oil relative permeability enabling gravity to drain the oil up. Anionic surfactants have been identified which at dilute concentration of 0.05 wt% and optimal salinity can lower the interfacial tension and change the wettability of the calcite surface to intermediate/water-wet condition as well or better than the cationic surfactant DTAB with a West Texas crude oil. The force of adhesion in AFM of oil-wet regions changes after anionic surfactant treatment to values similar to those of water-wet regions. The AFM topography images showed that the oil-wetting material was removed from the surface by the anionic surfactant treatment. Adsorption studies indicate that the extent of adsorption for anionic surfactants on calcite minerals decreases with increase in pH and with decrease in salinity. Surfactant adsorption can be minimized in the presence of Na{sub 2}CO{sub 3}. Laboratory-scale surfactant brine imbibition experiments give high oil recovery (20-42% OOIP in 50 days; up to 60% in 200 days) for initially oil-wet cores through wettability alteration and IFT reduction. Small (<10%) initial gas saturation does not affect significantly the rate of oil recovery in the imbibition process, but larger gas saturation decreases the oil recovery rate. As the core permeability decreases, the rate of oil recovery reduces

  7. Role of linker groups between hydrophilic and hydrophobic moieties of cationic surfactants on oligonucleotide-surfactant interactions.

    Science.gov (United States)

    Santhiya, Deenan; Dias, Rita S; Shome, Anshupriya; Das, Prasanta Kumar; Miguel, Maria G; Lindman, Björn; Maiti, Souvik

    2009-12-15

    The interaction between DNA and amino-acid-based surfactants with different linker groups was investigated by gel electrophoresis, ethidium bromide exclusion assays, circular dichroism, and melting temperature determinations. The studies showed that the strength of the interaction between the oligonucleotides and the surfactants is highly dependent on the linker of the surfactant. For ester surfactants, no significant interaction was observed for surfactant-to-DNA charge ratios up to 12. On the other hand, amide surfactants were shown to interact strongly with the oligonucleotides; these surfactants could displace up to 75% of the ethidium bromide molecules bound to the DNA and induced significant changes in the circular dichroism spectra. When comparing the headgroups of the surfactants, it was observed that surfactants with more hydrophobic headgroups (proline vs alanine) interacted more strongly with the DNA, in good agreement with previous studies.

  8. The effects of alkylammonium counterions on the aggregation of fluorinated surfactants and surfactant ionic liquids.

    Science.gov (United States)

    Pottage, Matthew J; Greaves, Tamar L; Garvey, Christopher J; Tabor, Rico F

    2016-08-01

    The effects of organic counterions with varying carbon number on surfactant aggregation have been analysed by coupling perfluorooctanoate surfactant anions with various alkylammonium counterions. Both the degree of substitution (primary to tertiary) and alkyl chain length (0-3 carbons) of the counterions were varied to provide a comprehensive matrix of geometries and lipophilicities. Surface activity was measured using pendant drop tensiometry, while temperature-controlled small-angle neutron scattering was used to probe changes in aggregation morphology. It was found that the use of such alkylammonium counterions resulted in a strong preference for bilayer formation even at low surfactant concentration (surfactant-rich lamellar phase coexists with a dilute micellar phase. The results indicate that aggregation is controlled by a delicate balance of counterion size, hydrophilicity and diffuseness of charge, providing new methods for the subtle control of surfactant solutions. Crown Copyright © 2016. Published by Elsevier Inc. All rights reserved.

  9. Spectrophotometric determination of uranium using 2-(2- Thiazolylazo-p-Cresol (TAC in the presence of surfactants

    Directory of Open Access Journals (Sweden)

    Teixeira Leonardo Sena Gomes

    1999-01-01

    Full Text Available A sensitive and selective spectrophotometric method is proposed for the rapid determination of uranium using 2-(2- Thiazolylazo-p-Cresol (TAC. The reaction between TAC and uranium (VI is instantaneous at pH 6.5 and the absorbance remains stable for over 3 h. N-cetyl-N,N,N-trimethylamonium bromide (CTAB and triton X-100 are used for increasing the sensitivity and solubility of the system respectively. The method allows the determination of uranium in the range from 0.30 to 12.0 mug mL-1 with a molar absorptivity of 1.31 x 10(4 L mol-1 cm-1 and features a detection limit of 26 ng mL-1 at 588 nm. The selectivity of the reagent was improved by the use of (1,2-cyclohexylenedinitrilo tetraacetic acid (CyDTA as masking agent. The proposed method has been successfully applied to the determination of uranium in mine drainage waters. The precision (R.S.D. < 2% and the accuracy obtained were satisfactory.

  10. Surfactants and the Mechanics of Respiration

    Science.gov (United States)

    Jbaily, Abdulrahman; Szeri, Andrew J.

    2016-11-01

    Alveoli are small sacs found at the end of terminal bronchioles in human lungs with a mean diameter of 200 μm. A thin layer of fluid (hypophase) coats the inner face of an alveolus and is in contact with the air in the lungs. The thickness of this layer varies among alveoli, but is in the range of 0.1 to 0.5 μm for many portions of the alveolar network. The interfacial tension σ at the air-hypophase interface tends to favor collapse of the alveolus, and resists its expansion during inhalation. Type II alveolar cells synthesize and secrete a mixture of phospholipids and proteins called pulmonary surfactant. These surfactant molecules adsorb to the interface causing σ of water at body temperature is 70 mN/m and falls to an equilibrium value of 25 mN/m when surfactants are present. Also, in a dynamic sense, it is known that σ is reduced to near 0 during exhalation when the surfactant film compresses. In this work, the authors develop a mechanical and transport model of the alveolus to study the effect of surfactants on various aspects of respiration. The model is composed of three principal parts: (i) air movement into and out of the alveolus; (ii) a balance of linear momentum across the two-layered membrane of the alveolus (hypophase and elastic wall); and (iii) a pulmonary surfactant transport problem in the hypophase. The goal is to evaluate the influence of pulmonary surfactant on respiratory mechanics.

  11. Isolation of surfactant-resistant bacteria from natural, surfactant-rich marine habitats.

    Science.gov (United States)

    Plante, Craig J; Coe, Kieran M; Plante, Rebecca G

    2008-08-01

    Environmental remediation efforts often utilize either biodegradative microbes or surfactants, but not in combination. Coupling both strategies holds the potential to dramatically increase the rate and extent of remediation because surfactants can enhance the bioavailability of contaminants to microbes. However, many surfactants permeabilize bacterial cell membranes and are effective disinfectants. An important goal then is to find or genetically modify microorganisms that possess both desirable degradative capabilities and the ability to thrive in the presence of surfactants. The guts of some marine invertebrates, particularly deposit feeders, have previously been shown to contain high levels of biosurfactants. Our primary aim was to mine these natural, surfactant-rich habitats for surfactant-resistant bacteria. Relative to sediment porewaters, the gut contents of two polychaete deposit feeders, Nereis succinea and Amphitrite ornata, exhibited a significantly higher ratio of bacteria resistant to both cationic and anionic surfactants. In contrast, bacteria in the gut fluids of a holothuroid, Leptosynapta tenuis, showed surfactant susceptibility similar to that of bacteria from sediments. Analyses of 16S rRNA gene sequences revealed that the majority of surfactant-resistant isolates were previously undescribed species of the genus Vibrio or were of a group most closely related to Spongiobacter spp. We also tested a subset of resistant bacteria for the production of biosurfactants. The majority did produce biosurfactants, as demonstrated via the oil-spreading method, but in all cases, production was relatively weak under the culture conditions employed. Novel surfactant-resistant, biosurfactant-producing bacteria, and the habitats from which they were isolated, provide a new source pool for potential microorganisms to be exploited in the in situ bioremediation of marine sediments.

  12. Isolation of Surfactant-Resistant Bacteria from Natural, Surfactant-Rich Marine Habitats▿

    Science.gov (United States)

    Plante, Craig J.; Coe, Kieran M.; Plante, Rebecca G.

    2008-01-01

    Environmental remediation efforts often utilize either biodegradative microbes or surfactants, but not in combination. Coupling both strategies holds the potential to dramatically increase the rate and extent of remediation because surfactants can enhance the bioavailability of contaminants to microbes. However, many surfactants permeabilize bacterial cell membranes and are effective disinfectants. An important goal then is to find or genetically modify microorganisms that possess both desirable degradative capabilities and the ability to thrive in the presence of surfactants. The guts of some marine invertebrates, particularly deposit feeders, have previously been shown to contain high levels of biosurfactants. Our primary aim was to mine these natural, surfactant-rich habitats for surfactant-resistant bacteria. Relative to sediment porewaters, the gut contents of two polychaete deposit feeders, Nereis succinea and Amphitrite ornata, exhibited a significantly higher ratio of bacteria resistant to both cationic and anionic surfactants. In contrast, bacteria in the gut fluids of a holothuroid, Leptosynapta tenuis, showed surfactant susceptibility similar to that of bacteria from sediments. Analyses of 16S rRNA gene sequences revealed that the majority of surfactant-resistant isolates were previously undescribed species of the genus Vibrio or were of a group most closely related to Spongiobacter spp. We also tested a subset of resistant bacteria for the production of biosurfactants. The majority did produce biosurfactants, as demonstrated via the oil-spreading method, but in all cases, production was relatively weak under the culture conditions employed. Novel surfactant-resistant, biosurfactant-producing bacteria, and the habitats from which they were isolated, provide a new source pool for potential microorganisms to be exploited in the in situ bioremediation of marine sediments. PMID:18586977

  13. A comparison study of the 1MeV triton burn-up in JET using the HECTOR and SOCRATE codes

    International Nuclear Information System (INIS)

    Gorini, G.; Kovanen, M.A.

    1988-01-01

    The burn-up of the 1MeV tritons in deuterium plasmas has been measured in JET for various plasma conditions. To interpret these measurements the containment, slowing down and burn-up of fast tritons needs to be modelled with a reasonable accuracy. The numerical code SOCRATE has been written for this specific purpose and a second code, HECTOR, has been adapted to study the triton burn-up problem. In this paper we compare the results from the two codes in order to exclude possible errors in the numerical models, to assess their accuracy and to study the sensitivity of the calculation to various physical effects. (author)

  14. Recovering hydrocarbons with surfactants from lignin

    Energy Technology Data Exchange (ETDEWEB)

    Naae, D.G.; Whittington, L.E.; Ledoux, W.A.; Debons, F.E.

    1988-11-29

    This patent describes a method of recovering hydrocarbons from an underground hydrocarbon formation penetrated by at least one injection well and at least one production well, which comprises: injecting into the formation through an injection well a surfactant slug comprising about 0.1% to about 10% by weight of surfactants produced from lignin, the surfactants produced by placing lignin in contact with water, converting the lignin into low molecular weight lignin phenols by reducing the lignin in the presence of a reducing agent of carbon monoxide or hydrogen creating a reduction reaction mixture comprising oil soluble lignin phenols, the reduction occurring at a temperature greater than about 200/sup 0/C and a pressure greater than about 100 psi, recovering the oil soluble lignin phenols from the reduction mixture, and converting the lignin phenols into lignin surfactants by a reaction selected from the group consisting of alkoxylation, sulfonation, sulfation, aklylation, sulfomethylation, and alkoxysulfation; injecting into the formation through the injection well a drive fluid to push the surfactant slug towards a production well; and recovering hydrocarbons at the production well.

  15. History of surfactant up to 1980.

    Science.gov (United States)

    Obladen, Michael

    2005-01-01

    Remarkable insight into disturbed lung mechanics of preterm infants was gained in the 18th and 19th century by the founders of obstetrics and neonatology who not only observed respiratory failure but also designed devices to treat it. Surfactant research followed a splendid and largely logical growth curve. Pathological changes in the immature lung were characterized in Germany by Virchow in 1854 and by Hochheim in 1903. The Swiss physiologist von Neergard fully understood surfactant function in 1929, but his paper was ignored for 25 years. The physical properties of surfactant were recognized in the early 1950s from research on warfare chemicals by Pattle in Britain and by Radford and Clements in the United States. The causal relationship of respiratory distress syndrome (RDS) and surfactant deficiency was established in the USA by Avery and Mead in 1959. The Australian obstetrician Liggins induced lung maturity with glucocorticoids in 1972, but his discovery was not fully believed for another 20 years. A century of basic research was rewarded when Fujiwara introduced surfactant substitution in Japan in 1980 for treatment and prevention of RDS. Copyright 2005 S. Karger AG, Basel

  16. Surface shear inviscidity of soluble surfactants.

    Science.gov (United States)

    Zell, Zachary A; Nowbahar, Arash; Mansard, Vincent; Leal, L Gary; Deshmukh, Suraj S; Mecca, Jodi M; Tucker, Christopher J; Squires, Todd M

    2014-03-11

    Foam and emulsion stability has long been believed to correlate with the surface shear viscosity of the surfactant used to stabilize them. Many subtleties arise in interpreting surface shear viscosity measurements, however, and correlations do not necessarily indicate causation. Using a sensitive technique designed to excite purely surface shear deformations, we make the most sensitive and precise measurements to date of the surface shear viscosity of a variety of soluble surfactants, focusing on SDS in particular. Our measurements reveal the surface shear viscosity of SDS to be below the sensitivity limit of our technique, giving an upper bound of order 0.01 μN·s/m. This conflicts directly with almost all previous studies, which reported values up to 10(3)-10(4) times higher. Multiple control and complementary measurements confirm this result, including direct visualization of monolayer deformation, for SDS and a wide variety of soluble polymeric, ionic, and nonionic surfactants of high- and low-foaming character. No soluble, small-molecule surfactant was found to have a measurable surface shear viscosity, which seriously undermines most support for any correlation between foam stability and surface shear rheology of soluble surfactants.

  17. Foaming behaviour of polymer-surfactant solutions

    International Nuclear Information System (INIS)

    Cervantes-MartInez, Alfredo; Maldonado, Amir

    2007-01-01

    We study the effect of a non-ionic amphiphilic polymer (PEG-100 stearate also called Myrj 59) on the foaming behaviour of aqueous solutions of an anionic surfactant (sodium dodecyl sulfate or SDS). The SDS concentration was kept fixed while the Myrj 59 concentration was varied. Measurements of foamability, surface tension and electrical conductivity were carried out. The results show two opposite effects depending on the polymer concentration: foamability is higher when the Myrj 59 concentration is low; however, it decreases considerably when the polymer concentration is increased. This behaviour is due to the polymer adsorption at the air/liquid interface at lower polymer concentrations, and to the formation of a polymer-surfactant complex in the bulk at higher concentrations. The results are confirmed by surface tension and electrical conductivity measurements, which are interpreted in terms of the microstructure of the polymer-surfactant solutions. The observed behaviour is due to the amphiphilic nature of the studied polymer. The increased hydrophobicity of Myrj 59, compared to that of water-soluble polymers like PEG or PEO, increases its 'reactivity' towards SDS, i.e. the strength of its interaction with this anionic surfactant. Our results show that hydrophobically modified polymers have potential applications as additives in order to control the foaming properties of surfactant solutions

  18. Syntheses of surfactants from oleochemical epoxides

    Directory of Open Access Journals (Sweden)

    Warwel Siegfried

    2001-01-01

    Full Text Available Sugar-based surfactants were obtained in good yields (up to 100% under mild conditions (70°C, methanol or mixtures of methanol and water by ring-opening of terminal epoxides with aminopolyols, derived from glucose. Reaction of N-methyl glucamine with epoxides from even-numbered C4-C18 alpha-olefins or from terminal unsaturated fatty acid methyl esters leads to linear products, while corresponding reactions with N-dodecyl glucamine or glucamine yield surfactants with different Y-structures. Products obtained by conversion of omega-epoxy fatty acid methyl esters were saponificated with NaOH or hydrolyzed enzymatically to sodium salts or free acids respectively, which are amphoteric surfactants. Studies of the surfactants at different pH-values demonstrate different surface active properties in aqueous solutions. Critical micelle concentrations (c.m.c. in a range between 2 and 500mg/l and surface tensions of 25-40mN/m were measured for several of the synthesized sugar-based surfactants. The ring-opening products are rather poor foamers, whereas some of the corresponding hydrobromides show good foaming properties.

  19. Flotação da mistura argila-quartzo com surfactantes e estudos de pilarização

    Directory of Open Access Journals (Sweden)

    Janaina Piasson

    2011-01-01

    Full Text Available Clay is often employed as a catalyst, but quartz impurities can decrease the catalytic efficiency. Fine particles of clay can be purified by flotation. We examined the cationic surfactant hexadecyltrimethylammonium bromide (HTAB, the anionic sodium dodecyl sulfate (SDS and the non-ionic TRITON X-100 for separating the quartz impurities from clay. Using X-ray diffraction, the separation was monitored for changes in the peaks corresponding to clay and quartz. Cationic surfactant HTAB was most effective in separating the quartz-clay mixture and the selectivity can be explained by internal adsorption of the surfactant onto the clay and external adsorption onto the quartz.

  20. Probing nanoparticle effect in protein-surfactant complexes

    Science.gov (United States)

    Mehan, Sumit; Aswal, V. K.; Kohlbrecher, J.

    2015-06-01

    SANS experiments have been carried to probe the role of anionic silica nanoparticles in the anionic BSA protein-cationic DTAB surfactant complexes. In protein-surfactant complex, surfactant molecules aggregate to form micelle-like clusters along the unfolded polypeptide chains of the protein. The nanoparticle aggregation mediated by oppositely charged protein-surfactant complex coexists with the free protein-surfactant complexes in the nanoparticle-protein-surfactant system. There is rearrangement of micelles in adsorbed protein-surfactant complex on nanoparticles in leading to their (nanoparticle) aggregation. On the other hand, the unfolding of protein in free protein-surfactant complex is found to be significantly enhanced in presence of nanoparticles.

  1. Synthesis of mesoporous nano-hydroxyapatite by using zwitterions surfactant

    Science.gov (United States)

    Mesoporous nano-hydroxyapatite (mn-HAP) was successfully synthesized via a novel micelle-templating method using lauryl dimethylaminoacetic acid as zwitterionic surfactant. The systematic use of such a surfactant in combination with microwave energy inputenables the precise contr...

  2. Fullerene surfactants and their use in polymer solar cells

    Science.gov (United States)

    Jen, Kwan-Yue; Yip, Hin-Lap; Li, Chang-Zhi

    2015-12-15

    Fullerene surfactant compounds useful as interfacial layer in polymer solar cells to enhance solar cell efficiency. Polymer solar cell including a fullerene surfactant-containing interfacial layer intermediate cathode and active layer.

  3. Recent food applications of microbial surfactants.

    Science.gov (United States)

    Nitschke, Marcia; Silva, Sumária Sousa E

    2016-07-20

    Owing to their natural origin and environmental compatibility, interest in microbial surfactants or biosurfactants has gained attention during last few years. These characteristics fulfill the demand of regulatory agencies and society to use more sustained and green chemicals. Microbial-derived surfactants can replace synthetic surfactants in a great variety of industrial applications as detergents, foaming, emulsifiers, solubilizers, and wetting agents. Change in the trend of consumers toward natural from synthetic additives and the increasing health and environmental concerns have created demand for new "green" additives in foods. Apart from their inherent surface-active properties, biosurfactants have shown antimicrobial and anti-biofilm activities against food pathogens; therefore, biosurfactants can be versatile additives or ingredients of food processing. These interesting applications will be discussed in this review.

  4. Surfactant mediated liquid phase exfoliation of graphene

    Science.gov (United States)

    Narayan, Rekha; Kim, Sang Ouk

    2015-10-01

    Commercialization of graphene based applications inevitably requires cost effective mass production. From the early days of research on graphene, direct liquid phase exfoliation (LPE) of graphite has been considered as the most promising strategy to produce high-quality mono or few-layer graphene sheets in solvent dispersion forms. Substantial success has been achieved thus far in the LPE of graphene employing numerous solvent systems and suitable surfactants. This invited review article principally showcase the recent research progress as well as shortcomings of surfactant assisted LPE of graphene. In particular, a comprehensive assessment of the quality and yield of the graphene sheets produced by different categories of the surfactants are summarized. Future direction of LPE methods is also proposed for the eventual success of commercial applications.

  5. Nanotube Dispersions Made With Charged Surfactant

    Science.gov (United States)

    Kuper, Cynthia; Kuzma, Mike

    2006-01-01

    Dispersions (including monodispersions) of nanotubes in water at relatively high concentrations have been formulated as prototypes of reagents for use in making fibers, films, and membranes based on single-walled carbon nanotubes (SWNTs). Other than water, the ingredients of a dispersion of this type include one or more charged surfactant(s) and carbon nanotubes derived from the HiPco(TradeMark) (or equivalent) process. Among reagents known to be made from HiPco(TradeMark)(or equivalent) SWNTs, these are the most concentrated and are expected to be usable in processing of bulk structures and materials. Test data indicate that small bundles of SWNTs and single SWNTs at concentrations up to 1.1 weight percent have been present in water plus surfactant. This development is expected to contribute to the growth of an industry based on applied carbon nanotechnology. There are expected to be commercial applications in aerospace, avionics, sporting goods, automotive products, biotechnology, and medicine.

  6. Surfactant studies for bench-scale operation

    Science.gov (United States)

    Hickey, Gregory S.; Sharma, Pramod K.

    1993-01-01

    A phase 2 study has been initiated to investigate surfactant-assisted coal liquefaction, with the objective of quantifying the enhancement in liquid yields and product quality. This report covers the second quarter of work. The major accomplishments were: completion of coal liquefaction autoclave reactor runs with Illinois number 6 coal at processing temperatures of 300, 325, and 350 C, and pressures of 1800 psig; analysis of the filter cake and the filtrate obtained from the treated slurry in each run; and correlation of the coal conversions and the liquid yield quality to the surfactant concentration. An increase in coal conversions and upgrading of the liquid product quality due to surfactant addition was observed for all runs.

  7. Brine-resistant sulfonate surfactants for enhanced oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Stournas, S.

    1983-01-01

    One of the most severe limitations of surfactant waterflooding is the instability of the commonly employed surfactants in the usual ionic environments of oil reservoirs. A specific modification to the usual structure of sulfonate surfactants not only makes them immune to high concentrations of monovalent and divalent cations, but also enables them to act as stabilizer of the common surfactants and to displace tertiary oil in brines of high salinity and divalent ion content.

  8. A Review on Progress in QSPR Studies for Surfactants

    OpenAIRE

    Zhengwu Wang; Xiaoyi Zhang; Jiwei Hu

    2010-01-01

    This paper presents a review on recent progress in quantitative structure-property relationship (QSPR) studies of surfactants and applications of various molecular descriptors. QSPR studies on critical micelle concentration (cmc) and surface tension (γ) of surfactants are introduced. Studies on charge distribution in ionic surfactants by quantum chemical calculations and its effects on the structures and properties of the colloids of surfactants are also reviewed. The trends of QSPR studies o...

  9. Novel surfactant-selective membrane electrode based on polyelectrolyte-surfactant complex.

    Science.gov (United States)

    Zorin, Ivan; Scherbinina, Tatiana; Fetin, Petr; Makarov, Ivan; Bilibin, Alexander

    2014-12-01

    Novel class of active ionophores for surfactant selective electrodes is proposed. PVC membrane doped with polyelectrolyte-surfactant stoichiometric complex is used for ion-selective electrode construction responsive to cetyltrimethyl ammonium bromide and related surfactants. New ionophore is quite stable and completely insoluble in aqueous media in wide range of pH. The electrode displays nearly Nernstian slope in CTAB concentration range 10(-6)-10(-3)M. Polyelectrolyte platform allows to design wide range of different ionophores responsive to cationic organic substances. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. Methods for constraining surface properties and volatile migration on Phoebe, Triton, Pluto, and the moon

    Science.gov (United States)

    Miller, Charles Frederick

    The surface properties and surface volatile content of rocky bodies contain clues as to the formation and subsequent evolution of our Solar System. Many Solar System bodies retain essentially pristine subsurface volatiles, but their surface volatiles have often undergone chemical processing from UV irradiation and heating from impacts over millennia. The result is a wide range of surface properties observed today. We analyze the surfaces of these primitive bodies with the goal of deducing their evolutionary history. To this end, we employed three targeted analysis methods to characterize the surface properties and/or volatile distribution of three Solar System satellites. We derived photometric properties of Saturn's moon Phoebe from observations taken at low solar phase angles and corn-pared these results to those published for other Solar System objects. We conclude that Phoebe's surface has similarities to both Jupiter family comets and Kuiper Belt Objects (KBOs), supporting the conjecture that Phoebe migrated to Saturn the outer Solar System. We converted a General Circulation Model (GCM) to simulate the atmospheric motion of Neptune's moon Triton. We used this model to investigate the effect of N2 surface frosts on Triton's global atmospheric circulation. Our simulations identified specific atmospheric thermal conditions that led to wind speeds and directions consistent with the motion of erupting geysers captured by Voyager 2 images. Finally, we developed an 3-D n-body ballistic plume model to analyze the geometry and dynamics of the ejecta plume created by the impact of the Lunar CRater Observation and Sensing Satellite (LCROSS) on the Moon. LCROSS was designed to detect water content in lunar regolith, but also served as a test bed for comparing the properties of a large-scale, controlled impact with laboratory impact experiments. By comparing plume simulation results to our observations of the LCROSS impact, we confirmed the predictions that the LCROSS

  11. Enhancing enzymatic hydrolysis of coconut husk through Pseudomonas aeruginosa AP 029/GLVIIA rhamnolipid preparation.

    Science.gov (United States)

    de Araújo, Cynthia Kérzia Costa; de Oliveira Campos, Alan; de Araújo Padilha, Carlos Eduardo; de Sousa Júnior, Francisco Canindé; do Nascimento, Ruthinéia Jéssica Alves; de Macedo, Gorete Ribeiro; Dos Santos, Everaldo Silvino

    2017-08-01

    This work investigated the influence of chemical (Triton X-100) and biological surfactant preparation (rhamnolipids) in coconut husk hydrolysis that was subjected to pretreatment with acid-alkali or alkaline hydrogen peroxide. The natural and pretreated biomass was characterized using the National Renewable Energy Laboratory protocol analysis as well as X-ray diffraction and scanning electron microscopy. The results demonstrated that in terms of the total reducing sugars, there was no significant difference between the hydrolysis using Triton X-100 and rhamnolipids, regardless of the pretreatment. A cellulosic conversion value as high as 33.0% was obtained in experiments with rhamnolipids. The coconut husk was observed to be a potential biomass that could produce second generation ethanol, and the rhamnolipid preparation can be used to support for the enzymatic hydrolysis, enhancing the advantage of cellulose conversion into glucose over chemical surfactants because it is an environmentally friendly approach. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Surfactant therapy in late preterm infants

    Directory of Open Access Journals (Sweden)

    Murat Yurdakök

    2013-06-01

    Full Text Available Late preterm (LPT neonates are at a high risk for respiratory distress soon after birth due to respiratory distress syndrome (RDS, transient tachypnea of the newborn, persistent pulmonary hypertension, and pneumonia along with an increased need for surfactant replacement therapy, continuous positive airway pressure, and ventilator support when compared with the term neonates. In the past, studies on outcomes of infants with respiratory distress have primarily focused on extremely premature infants, leading to a gap in knowledge and understanding of the developmental biology and mechanism of pulmonary diseases in LPT neonates. Surfactant deficiency is the most frequent etiology of RDS in very preterm and moderately preterm infants, while cesarean section and lung infection play major roles in RDS development in LPT infants. The clinical presentation and the response to surfactant therapy in LPT infants may be different than that seen in very preterm infants. Incidence of pneumonia and occurrence of pneumothorax are significantly higher in LPT and term infants. High rates of pneumonia in these infants may result in direct injury to the type II alveolar cells of the lung with decreasing synthesis, release, and processing of surfactant. Increased permeability of the alveolar capillary membrane to both fluid and solutes is known to result in entry of plasma proteins into the alveolar hypophase, further inhibiting the surface properties of surfactant. However, the oxygenation index value do not change dramatically after ventilation or surfactant administration in LPT infants with RDS compared to very preterm infants. These finding may indicate a different pathogenesis of RDS in late preterm and term infants. In conclusion, surfactant therapy may be of significant benefit in LPT infants with serious respiratory failure secondary to a number of insults. However, optimal timing and dose of administration are not so clear in this group. Additional

  13. INTERACTIONS BETWEEN WATER-SOLUBLE NONIONIC POLYMERS AND SURFACTANT AGGREGATES

    NARCIS (Netherlands)

    BRACKMAN, JC; ENGBERTS, JBFN; Herb, CA; Prudhomme, RK

    1994-01-01

    The influence of the chemical structure and charge of the surfactant on polymer-micelle interaction has been studied using various ionic and non-ionic surfactants, and surfactants of which the charge can be varied by (de)protonation. Octylthioglucoside, dodecyldimethylamine-oxide, alkylphosphates,

  14. Phenanthrene partitioning in sediment-surfactant-fresh/saline water systems

    International Nuclear Information System (INIS)

    Sun Hongwen; Wu Wenling; Wang Lei

    2009-01-01

    The objective of this study was to investigate the influence of salinity on the effectiveness of surfactants in the remediation of sediments contaminated with phenanthrene (PHE). This is an example of a more general application of surfactants in removing hydrophobic organic compounds (HOCs) from contaminated soil/sediment in saline environments via in-situ enhanced sorption or ex-situ soil washing. Salinity effects on surfactant micelle formation and PHE partitioning into solution surfactant micelles and sorbed surfactant were investigated. The critical micelle concentration of surfactants decreased, and PHE partition between surfactant micelles and water increased with increasing salinity. Carbon-normalized partition coefficients (K ss ) of PHE onto the sorbed cationic surfactant increased significantly with increasing salinity, which illustrates a more pronounced immobilization of PHE by cationic surfactant in a saline system. Reduction of PHE sorption by anionic surfactant was more pronounced in the saline system, indicating that the anionic surfactant has a higher soil washing effectiveness in saline systems. - The effectiveness of surfactant-enhanced remediation technology was promoted when applying it in estuarine environment with a higher salinity.

  15. The Inhibiting or Accelerating Effect of Different Surfactants on ...

    African Journals Online (AJOL)

    NICO

    The course of differential capacity curves of the electric double layer at the mercury electrode/surfactant solution interface was described for three different surfactants from different groups. Using square-wave voltammetry (SWV) it was found that the surfactants had a varying effect on the kinetics of electroreduction of Zn2+ ...

  16. Micellization of a Cationic Surfactant in Mixed Aqueous and Non ...

    African Journals Online (AJOL)

    Reception

    surfactant molecules arrange themselves in bulk solutions into aggregates otherwise called micelles when the interface is fully saturated with the surfactant molecules. Micelle formation is driven by hydrophobic effect but opposed by electrostatic repulsion of the ionic head group (Jiang et al., 2009). Cationic surfactants like ...

  17. Adsorption of anionic surfactants in limestone medium during oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Canbolat, Serhat; Bagci, Suat [Middle East Technical Univ., Dept. of Petroleum and Natural Gas Engineering, Ankara (Turkey)

    2004-07-15

    Foam-forming surfactant performance was evaluated by several experimental methods (interfacial tension, foam stability, corefloods) using commercial surfactants. There is considerable interest in the use of foam-forming surfactants for mobility control in water flood. To provide effective mobility control, the injected surfactant must propagate from the injection well toward the production well. One of the important parameters affecting propagation of foam-forming surfactant through the reservoir is the retention of surfactant due to its adsorption on reservoir rock. The determination of the adsorption of foam-forming surfactants in limestone reservoirs is important for the residual oil recovery efficiency. Adsorption measurements, recovery efficiencies, and surfactant and alkaline flooding experiments carried out with the representative of the selected surfactants alkaline solutions, linear alkyl benzene sulphonic acid (LABSA), sodium lauryl ether sulfate (SLES), and NaOH in a limestone medium. These surfactants were selected with respect to their foaming ability. Calibration curves formed by pH measurements were used to determine the correct adsorption amount of the used surfactants and recovery efficiency of these surfactants compared with base waterflooding. The results showed that LABSA adsorbed more than SLES in limestone reservoirs. The recovery efficiency of SLES was higher than the recovery efficiency of LABSA, and they decreased the recovery efficiency with respect to only the water injection case. (Author)

  18. Effects of selected surfactants on soil microbial activity

    Science.gov (United States)

    Surfactants (surface-active agents) facilitate and accentuate the emulsifying, dispersing, spreading, and wetting properties of liquids. Surfactants are used in industry to reduce the surface tension of liquid and to solubilize compounds. For agricultural pest management, surfactants are an import...

  19. Description of WWER-440 fuel assembly 3D depletion model developed with TRITON6 code (SCALE 6.0)

    International Nuclear Information System (INIS)

    2014-07-01

    One of the key components strongly influencing the accuracy of burnup credit methodology is precision of spent nuclear fuel isotopic composition prediction. To enhance the accuracy of spent nuclear fuel isotopic composition prediction modeling 3D depletion model of WWER-440 nuclear fuel was developed by TRITON6. TRITON6 couples ORIGEN-S depletion code with 3D neutron transport solver KENO-VI. This kind of coupling allows updating the ORIGEN-S cross-section libraries by 3D problem-dependent neutron fluxes computed by KENO-VI hence significantly improving the accuracy of isotopic composition predications. WWER-440 fuel assembly destructive experimental results carried out by RIAR Dimitrovgrad are planned to be used for verification and validation of developed model. Therefore WWER-440 fuel assembly model was developed with taking into account peculiarities in destructive experimental results

  20. OSS (Outer Solar System): A fundamental and planetary physics mission to Neptune, Triton and the Kuiper Belt

    OpenAIRE

    Christophe, Bruno; Spilker, Linda J.; Anderson, John D.; André, Nicolas; Asmar, Sami W.; Aurnou, Jonathan; Banfield, Don; Barucci, Antonella; Bertolami, Orfeu; Bingham, Robert; Brown, Patrick; Cecconi, Baptiste; Courty, Jean-Michel; Dittus, Hansjörg; Fletcher, Leigh N.

    2011-01-01

    The present OSS mission continues a long and bright tradition by associating the communities of fundamental physics and planetary sciences in a single mission with ambitious goals in both domains. OSS is an M-class mission to explore the Neptune system almost half a century after flyby of the Voyager 2 spacecraft. Several discoveries were made by Voyager 2, including the Great Dark Spot (which has now disappeared) and Triton's geysers. Voyager 2 revealed the dynamics of Neptune's atmosphere a...